package/boot/uboot-sunxi/patches/003-add-theobroma-a31-pangolin.patch

   1 diff -ruN a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
   2 --- a/arch/arm/dts/Makefile     2016-01-12 15:06:54.000000000 +0100
   3 +++ b/arch/arm/dts/Makefile     2016-01-30 15:31:50.000000000 +0100
   4 @@ -142,6 +142,7 @@
   5         sun6i-a31-m9.dtb \
   6         sun6i-a31-mele-a1000g-quad.dtb \
   7         sun6i-a31-mixtile-loftq.dtb \
   8 +       sun6i-a31-pangolin.dtb \
   9         sun6i-a31s-cs908.dtb \
  10         sun6i-a31s-primo81.dtb \
  11         sun6i-a31s-sinovoip-bpi-m2.dtb
  12 diff -ruN a/arch/arm/dts/sun6i-a31.dtsi b/arch/arm/dts/sun6i-a31.dtsi
  13 --- a/arch/arm/dts/sun6i-a31.dtsi       2016-01-12 15:06:54.000000000 +0100
  14 +++ b/arch/arm/dts/sun6i-a31.dtsi       2016-01-31 15:06:47.000000000 +0100
  15 @@ -643,6 +643,13 @@
  16                                 allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
  17                         };
  18
  19 +                       i2c3_pins_a: i2c3@0 {
  20 +                               allwinner,pins = "PB5", "PB6";
  21 +                               allwinner,function = "i2c3";
  22 +                               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
  23 +                               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
  24 +                       };
  25 +
  26                         mmc0_pins_a: mmc0@0 {
  27                                 allwinner,pins = "PF0", "PF1", "PF2",
  28                                                  "PF3", "PF4", "PF5";
  29 diff -ruN a/arch/arm/dts/sun6i-a31-pangolin.dts b/arch/arm/dts/sun6i-a31-pangolin.dts
  30 --- a/arch/arm/dts/sun6i-a31-pangolin.dts       1970-01-01 01:00:00.000000000 +0100
  31 +++ b/arch/arm/dts/sun6i-a31-pangolin.dts       2016-02-09 01:21:44.965168099 +0100
  32 @@ -0,0 +1,292 @@
  33 +/*
  34 + * Copyright 2015, Theobroma Systems Design und Consulting GmbH
  35 + *
  36 + * This file is dual-licensed: you can use it either under the terms
  37 + * of the GPL or the X11 license, at your option. Note that this dual
  38 + * licensing only applies to this file, and not this project as a
  39 + * whole.
  40 + *
  41 + *  a) This file is free software; you can redistribute it and/or
  42 + *     modify it under the terms of the GNU General Public License as
  43 + *     published by the Free Software Foundation; either version 2 of the
  44 + *     License, or (at your option) any later version.
  45 + *
  46 + *     This file is distributed in the hope that it will be useful,
  47 + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
  48 + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  49 + *     GNU General Public License for more details.
  50 + *
  51 + * Or, alternatively,
  52 + *
  53 + *  b) Permission is hereby granted, free of charge, to any person
  54 + *     obtaining a copy of this software and associated documentation
  55 + *     files (the "Software"), to deal in the Software without
  56 + *     restriction, including without limitation the rights to use,
  57 + *     copy, modify, merge, publish, distribute, sublicense, and/or
  58 + *     sell copies of the Software, and to permit persons to whom the
  59 + *     Software is furnished to do so, subject to the following
  60 + *     conditions:
  61 + *
  62 + *     The above copyright notice and this permission notice shall be
  63 + *     included in all copies or substantial portions of the Software.
  64 + *
  65 + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
  66 + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
  67 + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
  68 + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
  69 + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
  70 + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
  71 + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
  72 + *     OTHER DEALINGS IN THE SOFTWARE.
  73 + */
  74 +
  75 +/dts-v1/;
  76 +#include "sun6i-a31.dtsi"
  77 +#include "sunxi-common-regulators.dtsi"
  78 +
  79 +#include <dt-bindings/gpio/gpio.h>
  80 +#include <dt-bindings/pinctrl/sun4i-a10.h>
  81 +
  82 +/ {
  83 +       model = "Theobroma Systems A31 Pangolin";
  84 +       compatible = "tsd,a31-pangolin", "allwinner,sun6i-a31";
  85 +
  86 +       aliases {
  87 +               serial0 = &uart0;
  88 +               serial2 = &uart2;
  89 +               spi0 = &spi0;
  90 +               spi1 = &spi1;
  91 +               spi2 = &spi2;
  92 +               spi3 = &spi3;
  93 +       };
  94 +
  95 +       chosen {
  96 +               stdout-path = "serial2:115200n8";
  97 +       };
  98 +};
  99 +
 100 +&ehci0 {
 101 +       status = "okay";
 102 +};
 103 +
 104 +&ohci0 {
 105 +       status = "okay";
 106 +};
 107 +
 108 +&ehci1 {
 109 +       status = "okay";
 110 +};
 111 +
 112 +&ohci1 {
 113 +       status = "okay";
 114 +};
 115 +
 116 +&ohci2 {
 117 +       status = "okay";
 118 +};
 119 +
 120 +&gmac {
 121 +       pinctrl-names = "default";
 122 +       pinctrl-0 = <&gmac_pins_rgmii_a>;
 123 +       phy = <&phy1>;
 124 +       phy-mode = "rgmii";
 125 +       snps,reset-gpio = <&pio 0 7 GPIO_ACTIVE_LOW>;
 126 +       snps,reset-active-low;
 127 +       snps,reset-delays-us = <0 10000 30000>;
 128 +       status = "okay";
 129 +
 130 +       phy1: ethernet-phy@4 {
 131 +               reg = <4>;
 132 +       };
 133 +};
 134 +
 135 +&i2c0 {
 136 +       pinctrl-names = "default";
 137 +       pinctrl-0 = <&i2c0_pins_a>;
 138 +       status = "okay";
 139 +};
 140 +
 141 +&i2c1 {
 142 +       pinctrl-names = "default";
 143 +       pinctrl-0 = <&i2c1_pins_a>;
 144 +       status = "okay";
 145 +};
 146 +
 147 +&i2c2 {
 148 +       pinctrl-names = "default";
 149 +       pinctrl-0 = <&i2c2_pins_a>;
 150 +       status = "okay";
 151 +};
 152 +
 153 +&i2c3 {
 154 +       pinctrl-names = "default";
 155 +       pinctrl-0 = <&i2c3_pins_a>;
 156 +       status = "okay";
 157 +
 158 +       rtc_twi: rtc@6f {
 159 +        compatible = "isil,isl1208";
 160 +        reg = <0x6f>;
 161 +       };
 162 +       fan: fan@18 {
 163 +               compatible = "ti,amc6821";
 164 +               reg = <0x18>;
 165 +               cooling-min-state = <0>;
 166 +               cooling-max-state = <9>;
 167 +               #cooling-cells = <2>;
 168 +       };
 169 +};
 170 +
 171 +&spi0 {
 172 +       status = "okay";
 173 +
 174 +       flash: flash@0 {
 175 +               compatible = "spansion,m25p40";
 176 +               spi-max-frequency = <16000000>;
 177 +               spi-cpol;
 178 +               spi-cpha;
 179 +       };
 180 +};
 181 +
 182 +&spi1 {
 183 +       status = "okay";
 184 +};
 185 +
 186 +&ir {
 187 +       pinctrl-names = "default";
 188 +       pinctrl-0 = <&ir_pins_a>;
 189 +       status = "okay";
 190 +};
 191 +
 192 +&mmc0 {
 193 +       pinctrl-names = "default";
 194 +       pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_pangolin>;
 195 +       vmmc-supply = <&reg_vcc3v0>;
 196 +       bus-width = <4>;
 197 +       cd-gpios = <&pio 2 19 GPIO_ACTIVE_LOW>; /* PC19 */
 198 +       status = "okay";
 199 +};
 200 +
 201 +&mmc0_pins_a {
 202 +       /* external pull-ups missing for some pins */
 203 +       allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 204 +};
 205 +
 206 +&mmc2 {
 207 +       pinctrl-names = "default";
 208 +       pinctrl-0 = <&mmc2_pins_a>;
 209 +       vmmc-supply = <&reg_vcc3v0>;
 210 +       bus-width = <8>;
 211 +       non-removable;
 212 +       status = "okay";
 213 +};
 214 +
 215 +&pio {
 216 +       mmc0_cd_pin_pangolin: mmc0_cd_pin@0 {
 217 +               allwinner,pins = "PC19";
 218 +               allwinner,function = "gpio_in";
 219 +               allwinner,drive = <SUN4I_PINCTRL_10_MA>;
 220 +               allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 221 +       };
 222 +
 223 +       leds_pins_pangolin: led_pins@0 {
 224 +               allwinner,pins = "PH7", "PC16";
 225 +               allwinner,function = "gpio_out";
 226 +               allwinner,drive = <SUN4I_PINCTRL_20_MA>;
 227 +               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 228 +       };
 229 +
 230 +       mmc2_pins_a: mmc2@0 {
 231 +               allwinner,pins = "PC6","PC7","PC8","PC9","PC10","PC11",
 232 +                               "PC12","PC13","PC14","PC15";
 233 +               allwinner,function = "mmc2";
 234 +               allwinner,drive = <SUN4I_PINCTRL_30_MA>;
 235 +               allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
 236 +       };
 237 +};
 238 +
 239 +&p2wi {
 240 +       status = "okay";
 241 +
 242 +       axp221: pmic@68 {
 243 +               compatible = "x-powers,axp221";
 244 +               reg = <0x68>;
 245 +               interrupt-parent = <&nmi_intc>;
 246 +               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 247 +               interrupt-controller;
 248 +               #interrupt-cells = <1>;
 249 +               dcdc1-supply = <&vcc_3v0>;
 250 +               dcdc5-supply = <&vcc_dram>;
 251 +
 252 +               regulators {
 253 +                       x-powers,dcdc-freq = <3000>;
 254 +
 255 +                       vcc_3v0: dcdc1 {
 256 +                               regulator-always-on;
 257 +                               regulator-min-microvolt = <3000000>;
 258 +                               regulator-max-microvolt = <3000000>;
 259 +                               regulator-name = "vcc-3v0";
 260 +                       };
 261 +
 262 +                       vdd_cpu: dcdc2 {
 263 +                               regulator-always-on;
 264 +                               regulator-min-microvolt = <700000>;
 265 +                               regulator-max-microvolt = <1320000>;
 266 +                               regulator-name = "vdd-cpu";
 267 +                       };
 268 +
 269 +                       vdd_gpu: dcdc3 {
 270 +                               regulator-always-on;
 271 +                               regulator-min-microvolt = <700000>;
 272 +                               regulator-max-microvolt = <1320000>;
 273 +                               regulator-name = "vdd-gpu";
 274 +                       };
 275 +
 276 +                       vdd_sys_dll: dcdc4 {
 277 +                               regulator-always-on;
 278 +                               regulator-min-microvolt = <1100000>;
 279 +                               regulator-max-microvolt = <1100000>;
 280 +                               regulator-name = "vdd-sys-dll";
 281 +                       };
 282 +
 283 +                       vcc_dram: dcdc5 {
 284 +                               regulator-always-on;
 285 +                               regulator-min-microvolt = <1500000>;
 286 +                               regulator-max-microvolt = <1500000>;
 287 +                               regulator-name = "vcc-dram";
 288 +                       };
 289 +
 290 +                       vcc_wifi: aldo1 {
 291 +                               regulator-min-microvolt = <3300000>;
 292 +                               regulator-max-microvolt = <3300000>;
 293 +                               regulator-name = "vcc_wifi";
 294 +                       };
 295 +
 296 +                       avcc: aldo3 {
 297 +                               regulator-always-on;
 298 +                               regulator-min-microvolt = <3000000>;
 299 +                               regulator-max-microvolt = <3000000>;
 300 +                               regulator-name = "avcc";
 301 +                       };
 302 +               };
 303 +       };
 304 +};
 305 +
 306 +&uart0 {
 307 +       pinctrl-names = "default";
 308 +       pinctrl-0 = <&uart0_pins_a>;
 309 +       status = "okay";
 310 +};
 311 +
 312 +&usb1_vbus_pin_a {
 313 +       allwinner,pins = "PD23";
 314 +};
 315 +
 316 +&reg_usb1_vbus {
 317 +       gpio = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD 23 */
 318 +       status = "okay";
 319 +};
 320 +
 321 +&usbphy {
 322 +       status = "okay";
 323 +       usb1_vbus-supply = <&reg_usb1_vbus>;
 324 +};
 325 diff -ruN a/configs/pangolin_defconfig b/configs/pangolin_defconfig
 326 --- a/configs/pangolin_defconfig        1970-01-01 01:00:00.000000000 +0100
 327 +++ b/configs/pangolin_defconfig        2016-01-30 14:43:59.000000000 +0100
 328 @@ -0,0 +1,36 @@
 329 +CONFIG_SUNXI_PANGOLIN=y
 330 +CONFIG_SPL=y
 331 +CONFIG_SYS_EXTRA_OPTIONS="USB_EHCI,SUNXI_GMAC,RGMII"
 332 +CONFIG_DEFAULT_DEVICE_TREE="sun6i-a31-pangolin"
 333 +CONFIG_VIDEO_VGA_VIA_LCD=y
 334 +CONFIG_VIDEO_VGA_EXTERNAL_DAC_EN="PH25"
 335 +CONFIG_ARM=y
 336 +CONFIG_ARCH_SUNXI=y
 337 +CONFIG_MACH_SUN6I=y
 338 +CONFIG_DRAM_CHANNELS=1
 339 +CONFIG_DRAM_CLK=360
 340 +CONFIG_DRAM_ZQ=70
 341 +CONFIG_AXP_DCDC1_VOLT=3300
 342 +CONFIG_AXP_ALDO1_VOLT=0
 343 +CONFIG_AXP_ALDO2_VOLT=1800
 344 +CONFIG_AXP_ALDO3_VOLT=3000
 345 +CONFIG_AXP_DLDO4_VOLT=3300
 346 +CONFIG_AXP_ELDO1_VOLT=1200
 347 +CONFIG_AXP_ELDO2_VOLT=2500
 348 +CONFIG_AXP_ELDO3_VOLT=3300
 349 +CONFIG_MMC_SUNXI_SLOT_EXTRA=2
 350 +CONFIG_CONS_INDEX=3
 351 +# Vbus gpio for usb1
 352 +CONFIG_USB1_VBUS_PIN=""
 353 +# No Vbus gpio for usb2
 354 +CONFIG_USB2_VBUS_PIN=""
 355 +CONFIG_USB=y
 356 +CONFIG_DM_USB=y
 357 +CONFIG_USB_EHCI=y
 358 +CONFIG_USB_KEYBOARD=y
 359 +CONFIG_DM_ETH=y
 360 +CONFIG_CMD_IMLS=n
 361 +CONFIG_ETH_DESIGNWARE=y
 362 +CONFIG_DM_SPI=y
 363 +CONFIG_DM_SPI_FLASH=y
 364 +CONFIG_SUNXI_SPI=y
 365 diff --git a/board/sunxi/Kconfig b/board/sunxi/Kconfig
 366 index e155c4c..1b147b2 100644
 367 --- a/board/sunxi/Kconfig
 368 +++ b/board/sunxi/Kconfig
 369 @@ -15,7 +15,6 @@ config SUNXI_GEN_SUN6I
 370         separate ahb reset control registers, custom pmic bus, new style
 371         watchdog, etc.
 372
 373 -
 374  choice
 375         prompt "Sunxi SoC Variant"
 376         optional
 377 @@ -80,6 +79,14 @@ config MACH_SUN8I
 378         bool
 379         default y if MACH_SUN8I_A23 || MACH_SUN8I_A33
 380
 381 +choice
 382 +       prompt "Sunxi Board Variant"
 383 +       optional
 384 +
 385 +config SUNXI_PANGOLIN
 386 +       bool "Theobroma A31 uQ7 Board"
 387 +
 388 +endchoice
 389
 390  config DRAM_CLK
 391         int "sunxi dram clock speed"
 392 --
 393 cgit v0.10.2
 394