target/linux/ath79/dts/qca9558_ocedo_ursus.dts

   1 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
   2 /dts-v1/;
   3
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/input/input.h>
   6
   7 #include "qca955x.dtsi"
   8
   9 / {
  10         compatible = "ocedo,ursus", "qca,qca9558";
  11         model = "OCEDO Ursus";
  12
  13         leds {
  14                 compatible = "gpio-leds";
  15
  16                 wifi2 {
  17                         label = "ursus:green:wlan2g";
  18                         gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
  19                         linux,default-trigger = "phy1tpt";
  20                 };
  21
  22                 wifi5 {
  23                         label = "ursus:green:wlan5g";
  24                         gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
  25                         linux,default-trigger = "phy0tpt";
  26                 };
  27         };
  28 };
  29
  30 &pcie1 {
  31         status = "okay";
  32 };
  33
  34 &uart {
  35         status = "okay";
  36 };
  37
  38 &pll {
  39         clocks = <&extosc>;
  40 };
  41
  42 &spi {
  43         status = "okay";
  44         num-cs = <1>;
  45
  46         flash@0 {
  47                 compatible = "jedec,spi-nor";
  48                 reg = <0>;
  49                 spi-max-frequency = <25000000>;
  50
  51                 partitions {
  52                         compatible = "fixed-partitions";
  53                         #address-cells = <1>;
  54                         #size-cells = <1>;
  55
  56                         uboot: partition@0 {
  57                                 label = "u-boot";
  58                                 reg = <0x000000 0x040000>;
  59                                 read-only;
  60                         };
  61
  62                         partition@40000 {
  63                                 label = "u-boot-env";
  64                                 reg = <0x040000 0x010000>;
  65                         };
  66
  67                         partition@50000 {
  68                                 compatible = "denx,uimage";
  69                                 label = "firmware";
  70                                 reg = <0x050000 0x740000>;
  71                         };
  72
  73                         partition@790000 {
  74                                 label = "vendor";
  75                                 reg = <0x790000 0x740000>;
  76                                 read-only;
  77                         };
  78
  79                         partition@ed0000 {
  80                                 label = "data";
  81                                 reg = <0xed0000 0x110000>;
  82                                 read-only;
  83                         };
  84
  85                         partition@fe0000 {
  86                                 label = "id";
  87                                 reg = <0xfe0000 0x010000>;
  88                                 read-only;
  89                         };
  90
  91                         art: partition@ff0000 {
  92                                 label = "art";
  93                                 reg = <0xff0000 0x010000>;
  94                                 read-only;
  95                         };
  96                 };
  97         };
  98 };
  99
 100 &wmac {
 101         status = "okay";
 102
 103         mtd-cal-data = <&art 0x1000>;
 104         mtd-mac-address = <&art 0x06>;
 105 };
 106
 107 &mdio0 {
 108         status = "okay";
 109
 110         phy1: ethernet-phy@1 {
 111                 reg = <1>;
 112         };
 113
 114         phy2: ethernet-phy@2 {
 115                 reg = <2>;
 116                 at803x-override-sgmii-link-check;
 117         };
 118 };
 119
 120 &eth0 {
 121         status = "okay";
 122         mtd-mac-address = <&art 0x00>;
 123
 124         phy-mode = "rgmii-rxid";
 125         phy-handle = <&phy1>;
 126         pll-data = <0x8e000000 0x80000101 0x80001313>;
 127
 128         gmac_config: gmac-config {
 129                 device = <&gmac>;
 130
 131                 rxdv-delay = <3>;
 132                 rxd-delay = <3>;
 133                 txen-delay = <0>;
 134                 txd-delay = <0>;
 135                 rgmii-enabled = <1>;
 136         };
 137 };
 138
 139 &eth1 {
 140         status = "okay";
 141         mtd-mac-address = <&art 0x12>;
 142         phy-handle = <&phy2>;
 143         pll-data = <0x3000101 0x101 0x1313>;
 144         qca955x-sgmii-fixup;
 145 };