1 // SPDX-License-Identifier: GPL-2.0-or-later
3 #include "qcom-ipq4019.dtsi"
4 #include <dt-bindings/gpio/gpio.h>
5 #include <dt-bindings/input/input.h>
6 #include <dt-bindings/soc/qcom,tcsr.h>
9 model = "EnGenius EAP1300";
10 compatible = "engenius,eap1300", "qcom,ipq4019";
22 compatible = "qcom,tcsr";
23 reg = <0x1949000 0x100>;
24 qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
28 compatible = "qcom,tcsr";
29 reg = <0x1953000 0x1000>;
30 qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
34 compatible = "qcom,tcsr";
35 reg = <0x1957000 0x100>;
36 qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
57 compatible = "gpio-keys";
61 gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
62 linux,code = <KEY_RESTART>;
68 led-failsafe = &power;
74 compatible = "gpio-leds";
77 label = "eap1300:orange:power";
78 gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
82 label = "eap1300:blue:lan";
83 gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
87 label = "eap1300:blue:mesh";
88 gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
92 label = "eap1300:blue:wlan2g";
93 gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
97 label = "eap1300:yellow:wlan5g";
98 gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
104 serial_pins: serial_pinmux {
106 pins = "gpio60", "gpio61";
107 function = "blsp_uart0";
112 spi_0_pins: spi_0_pinmux {
114 function = "blsp_spi0";
115 pins = "gpio54", "gpio55", "gpio56", "gpio57";
116 drive-strength = <12>;
122 drive-strength = <2>;
134 pinctrl-0 = <&spi_0_pins>;
135 pinctrl-names = "default";
137 cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
140 compatible = "jedec,spi-nor";
142 spi-max-frequency = <24000000>;
144 compatible = "fixed-partitions";
145 #address-cells = <1>;
150 reg = <0x00000000 0x00040000>;
155 reg = <0x00040000 0x00020000>;
160 reg = <0x00060000 0x00060000>;
165 reg = <0x000c0000 0x00010000>;
169 label = "0:DDRPARAMS";
170 reg = <0x000d0000 0x00010000>;
174 label = "0:APPSBLENV";
175 reg = <0x000e0000 0x00010000>;
180 reg = <0x000f0000 0x00090000>;
185 reg = <0x00180000 0x00010000>;
189 compatible = "denx,fit";
191 reg = <0x190000 0x1dc0000>;
194 label = "u-boot-env";
195 reg = <0x01f50000 0x00010000>;
197 partition10@1f60000 {
198 label = "userconfig";
199 reg = <0x01f60000 0x000a0000>;
206 pinctrl-0 = <&serial_pins>;
207 pinctrl-names = "default";
225 qcom,ath10k-calibration-variant = "EnGenius-EAP1300";
230 qcom,ath10k-calibration-variant = "EnGenius-EAP1300";