include $(TOPDIR)/rules.mk include $(INCLUDE_DIR)/image.mk DEVICE_VARS += RAS_BOARD RAS_ROOTFS_SIZE RAS_VERSION define Device/Default PROFILES := Default KERNEL_DEPENDS = $$(wildcard $(DTS_DIR)/$$(DEVICE_DTS).dts) KERNEL_INITRAMFS_PREFIX := $$(IMG_PREFIX)-$(1)-initramfs KERNEL_PREFIX := $$(IMAGE_PREFIX) KERNEL_LOADADDR := 0x80208000 SUPPORTED_DEVICES := $(subst _,$(comma),$(1)) IMAGE/sysupgrade.bin = sysupgrade-tar | append-metadata IMAGE/sysupgrade.bin/squashfs := endef define Device/FitImage KERNEL_SUFFIX := -fit-uImage.itb KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb KERNEL_NAME := Image endef define Device/FitImageLzma KERNEL_SUFFIX := -fit-uImage.itb KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb KERNEL_NAME := Image endef define Device/FitzImage KERNEL_SUFFIX := -fit-zImage.itb KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb KERNEL_NAME := zImage endef define Device/UbiFit KERNEL_IN_UBI := 1 IMAGES := nand-factory.ubi nand-sysupgrade.bin IMAGE/nand-factory.ubi := append-ubi IMAGE/nand-sysupgrade.bin := sysupgrade-tar | append-metadata endef define Device/DniImage KERNEL_SUFFIX := -fit-uImage.itb KERNEL = kernel-bin | gzip | fit gzip $$(DTS_DIR)/$$(DEVICE_DTS).dtb KERNEL_NAME := Image NETGEAR_BOARD_ID := NETGEAR_HW_ID := IMAGES := factory.img sysupgrade.bin IMAGE/factory.img := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | netgear-dni IMAGE/sysupgrade.bin := append-kernel | pad-offset 64k 64 | append-uImage-fakehdr filesystem | append-rootfs | pad-rootfs | append-metadata endef DEVICE_VARS += NETGEAR_BOARD_ID NETGEAR_HW_ID define Build/SenaoFW -$(STAGING_DIR_HOST)/bin/mksenaofw \ -n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \ -c $(DATECODE) -w $(2) -x $(CW_VER) -t 0 \ -e $@ \ -o $@.new @cp $@.new $@ endef define Device/8dev_jalapeno $(call Device/FitImage) $(call Device/UbiFit) DEVICE_DTS := qcom-ipq4018-jalapeno BLOCKSIZE := 128k PAGESIZE := 2048 DEVICE_TITLE := 8devices Jalapeno endef TARGET_DEVICES += 8dev_jalapeno define Device/alfa-network_ap120c-ac $(call Device/FitImage) $(call Device/UbiFit) DEVICE_TITLE := ALFA Network AP120C-AC DEVICE_DTS := qcom-ipq4018-ap120c-ac DEVICE_PACKAGES := ipq-wifi-alfa-network_ap120c-ac kmod-usb-acm \ kmod-tpm-i2c-atmel uboot-envtools BLOCKSIZE := 128k PAGESIZE := 2048 IMAGE_SIZE := 65536k IMAGES := nand-factory.bin nand-sysupgrade.bin IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand endef TARGET_DEVICES += alfa-network_ap120c-ac define Device/asus_map-ac2200 $(call Device/FitImageLzma) DEVICE_DTS := qcom-ipq4019-map-ac2200 DEVICE_TITLE := ASUS Lyra MAP-AC2200 IMAGES := sysupgrade.bin DEVICE_PACKAGES := ipq-wifi-asus_map-ac2200 ath10k-firmware-qca9888-ct kmod-ath3k endef TARGET_DEVICES += asus_map-ac2200 define Device/asus_rt-ac58u $(call Device/FitImageLzma) DEVICE_DTS := qcom-ipq4018-rt-ac58u BLOCKSIZE := 128k PAGESIZE := 2048 DTB_SIZE := 65536 DEVICE_TITLE := Asus RT-AC58U IMAGE_SIZE := 20439364 FILESYSTEMS := squashfs # Someone - in their infinite wisdom - decided to put the firmware # version in front of the image name \03\00\00\04 => Version 3.0.0.4 # Since u-boot works with strings we either need another fixup step # to add a version... or we are very careful not to add '\0' into that # string and call it a day.... Yeah, we do the latter! UIMAGE_NAME:=$(shell echo -e '\03\01\01\01RT-AC58U') IMAGES := sysupgrade.bin DEVICE_PACKAGES := kmod-usb-ledtrig-usbport endef TARGET_DEVICES += asus_rt-ac58u define Device/avm_fritzbox-4040 $(call Device/FitImageLzma) DEVICE_DTS := qcom-ipq4018-fritz4040 BOARD_NAME := fritz4040 DEVICE_TITLE := AVM Fritz!Box 4040 IMAGE_SIZE := 29753344 UBOOT_PATH := $(STAGING_DIR_IMAGE)/uboot-fritz4040.bin UBOOT_PARTITION_SIZE := 524288 IMAGES = eva.bin sysupgrade.bin IMAGE/eva.bin := append-uboot | pad-to $$$$(UBOOT_PARTITION_SIZE) | append-kernel | append-rootfs | pad-rootfs IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata DEVICE_PACKAGES := fritz-tffs fritz-caldata endef TARGET_DEVICES += avm_fritzbox-4040 define Device/avm_fritzbox-7530 $(call Device/FitImageLzma) DEVICE_DTS := qcom-ipq4019-fritzbox-7530 DEVICE_TITLE := AVM Fritz!Box 7530 DEVICE_PACKAGES := fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzbox-7530 IMAGES := sysupgrade.bin endef TARGET_DEVICES += avm_fritzbox-7530 define Device/avm_fritzrepeater-3000 $(call Device/FitImageLzma) DEVICE_DTS := qcom-ipq4019-fritzrepeater-3000 DEVICE_TITLE := AVM Fritz!Repeater 3000 DEVICE_PACKAGES := ath10k-firmware-qca9984-ct fritz-caldata fritz-tffs-nand ipq-wifi-avm_fritzrepeater-3000 IMAGES := sysupgrade.bin endef TARGET_DEVICES += avm_fritzrepeater-3000 define Device/compex_wpj428 $(call Device/FitImage) DEVICE_DTS := qcom-ipq4028-wpj428 DEVICE_DTS_CONFIG := config@4 BLOCKSIZE := 64k DEVICE_TITLE := Compex WPJ428 IMAGE_SIZE := 31232k KERNEL_SIZE := 4096k IMAGES = sysupgrade.bin IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata DEVICE_PACKAGES := kmod-gpio-beeper endef TARGET_DEVICES += compex_wpj428 define Device/engenius_eap1300 $(call Device/FitImage) DEVICE_TITLE := EnGenius EAP1300 DEVICE_DTS_CONFIG := config@4 BOARD_NAME := eap1300 DEVICE_DTS := qcom-ipq4018-eap1300 KERNEL_SIZE := 5120k IMAGE_SIZE := 25344k IMAGES := sysupgrade.bin IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata DEVICE_PACKAGES := ipq-wifi-engenius_eap1300 endef TARGET_DEVICES += engenius_eap1300 define Device/engenius_ens620ext $(call Device/FitImage) DEVICE_DTS := qcom-ipq4018-ens620ext DEVICE_DTS_CONFIG := config@4 BLOCKSIZE := 64k PAGESIZE := 256 DEVICE_TITLE := EnGenius ENS620EXT BOARD_NAME := ENS620EXT VENDOR_ID := 0x0101 PRODUCT_ID := 0x79 PRODUCT_ID_NEW := 0xA4 DATECODE := 190507 FW_VER := 3.1.2 FW_VER_NEW := 3.5.6 CW_VER := 1.8.99 IMAGE_SIZE := 21823488 KERNEL_SIZE := 5120k FILESYSTEMS := squashfs IMAGES := sysupgrade.bin factory_30.bin factory_35.bin IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | append-metadata IMAGE/factory_30.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-rootfs | pad-rootfs | check-size $$$$(IMAGE_SIZE) | SenaoFW $$$$(PRODUCT_ID) $$$$(FW_VER) IMAGE/factory_35.bin := qsdk-ipq-factory-nor | check-size $$$$(IMAGE_SIZE) | SenaoFW $$$$(PRODUCT_ID_NEW) $$$$(FW_VER_NEW) DEVICE_PACKAGES := ipq-wifi-engenius_ens620ext endef TARGET_DEVICES += engenius_ens620ext define Device/glinet_gl-b1300 $(call Device/FitImage) DEVICE_TITLE := GL.iNet GL-B1300 BOARD_NAME := gl-b1300 DEVICE_DTS := qcom-ipq4029-gl-b1300 KERNEL_SIZE := 4096k IMAGE_SIZE := 26624k IMAGES := sysupgrade.bin IMAGE/sysupgrade.bin := append-kernel |append-rootfs | pad-rootfs | append-metadata endef TARGET_DEVICES += glinet_gl-b1300 define Device/linksys_ea6350v3 # The Linksys EA6350v3 has a uboot bootloader that does not # support either booting lzma kernel images nor booting UBI # partitions. This uboot, however, supports raw kernel images and # gzipped images. # # As for the time of writing this, the device will boot the kernel # from a fixed address with a fixed length of 3MiB. Also, the # device has a hard-coded kernel command line that requieres the # rootfs and alt_rootfs to be in mtd11 and mtd13 respectively. # Oh... and the kernel partition overlaps with the rootfs # partition (the same for alt_kernel and alt_rootfs). # # If you are planing re-partitioning the device, you may want to # keep those details in mind: # 1. The kernel adresses you should honor are 0x00000000 and # 0x02800000 respectively. # 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size. # 3. You can use 'zImage', but not a raw 'Image' packed with lzma. # 4. The kernel command line from uboot is harcoded to boot with # rootfs either in mtd11 or mtd13. $(call Device/FitzImage) DEVICE_TITLE := Linksys EA6350v3 DEVICE_DTS := qcom-ipq4018-ea6350v3 BLOCKSIZE := 128k PAGESIZE := 2048 KERNEL_SIZE := 3145728 IMAGE_SIZE := 38797312 UBINIZE_OPTS := -E 5 IMAGES := factory.bin sysupgrade.bin IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA6350v3 DEVICE_PACKAGES := ipq-wifi-linksys_ea6350v3 uboot-envtools endef TARGET_DEVICES += linksys_ea6350v3 define Device/meraki_mr33 $(call Device/FitImage) DEVICE_DTS := qcom-ipq4029-mr33 BLOCKSIZE := 131072 PAGESIZE := 2048 DEVICE_TITLE := Cisco Meraki MR33 IMAGES = sysupgrade.bin DEVICE_PACKAGES := -swconfig ath10k-firmware-qca9887-ct endef TARGET_DEVICES += meraki_mr33 define Device/netgear_ex61x0v2 $(call Device/DniImage) DEVICE_DTS_CONFIG := config@4 NETGEAR_BOARD_ID := EX6150v2series NETGEAR_HW_ID := 29765285+16+0+128+2x2 endef define Device/netgear_ex6100v2 $(call Device/netgear_ex61x0v2) DEVICE_DTS := qcom-ipq4018-ex6100v2 DEVICE_TITLE := Netgear EX6100v2 endef TARGET_DEVICES += netgear_ex6100v2 define Device/netgear_ex6150v2 $(call Device/netgear_ex61x0v2) DEVICE_DTS := qcom-ipq4018-ex6150v2 DEVICE_TITLE := Netgear EX6150v2 endef TARGET_DEVICES += netgear_ex6150v2 define Device/openmesh_a42 $(call Device/FitImageLzma) DEVICE_DTS := qcom-ipq4018-a42 DEVICE_DTS_CONFIG := config@om.a42 BLOCKSIZE := 64k DEVICE_TITLE := OpenMesh A42 KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE) IMAGE_SIZE := 15616k IMAGES = factory.bin sysupgrade.bin IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A42 IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata DEVICE_PACKAGES := uboot-envtools endef TARGET_DEVICES += openmesh_a42 define Device/openmesh_a62 $(call Device/FitImageLzma) DEVICE_DTS := qcom-ipq4019-a62 DEVICE_DTS_CONFIG := config@om.a62 BLOCKSIZE := 64k DEVICE_TITLE := OpenMesh A62 KERNEL = kernel-bin | lzma | fit lzma $$(DTS_DIR)/$$(DEVICE_DTS).dtb | pad-to $$(BLOCKSIZE) IMAGE_SIZE := 15552k IMAGES = factory.bin sysupgrade.bin IMAGE/factory.bin := append-rootfs | pad-rootfs | openmesh-image ce_type=A62 IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | sysupgrade-tar rootfs=$$$$@ | append-metadata DEVICE_PACKAGES := ath10k-firmware-qca9888-ct uboot-envtools endef TARGET_DEVICES += openmesh_a62 define Device/qcom_ap-dk01.1-c1 DEVICE_TITLE := QCA AP-DK01.1-C1 BOARD_NAME := ap-dk01.1-c1 DEVICE_DTS := qcom-ipq4019-ap.dk01.1-c1 KERNEL_INSTALL := 1 KERNEL_SIZE := 4096k IMAGE_SIZE := 26624k $(call Device/FitImage) IMAGES := sysupgrade.bin IMAGE/sysupgrade.bin := append-kernel | pad-to $$$${KERNEL_SIZE} | append-rootfs | pad-rootfs | append-metadata endef TARGET_DEVICES += qcom_ap-dk01.1-c1 define Device/qcom_ap-dk04.1-c1 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_DTS := qcom-ipq4019-ap.dk04.1-c1 KERNEL_INSTALL := 1 KERNEL_SIZE := 4048k BLOCKSIZE := 128k PAGESIZE := 2048 BOARD_NAME := ap-dk04.1-c1 DEVICE_TITLE := QCA AP-DK04.1-C1 endef TARGET_DEVICES += qcom_ap-dk04.1-c1 define Device/qxwlan_e2600ac-c1 $(call Device/FitImage) DEVICE_TITLE := Qxwlan E2600AC-C1 (nor flash) BOARD_NAME := e2600ac-c1 DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c1 KERNEL_SIZE := 4096k IMAGE_SIZE := 31232k IMAGES := sysupgrade.bin IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac endef TARGET_DEVICES += qxwlan_e2600ac-c1 define Device/qxwlan_e2600ac-c2 $(call Device/FitImage) $(call Device/UbiFit) DEVICE_DTS := qcom-ipq4019-qxwlan-e2600ac-c2 KERNEL_INSTALL := 1 BLOCKSIZE := 128k PAGESIZE := 2048 DEVICE_TITLE := Qxwlan E2600AC-C2 (nornand flash) DEVICE_PACKAGES := ipq-wifi-qxwlan_e2600ac endef TARGET_DEVICES += qxwlan_e2600ac-c2 define Device/zyxel_nbg6617 $(call Device/FitImageLzma) DEVICE_DTS := qcom-ipq4018-nbg6617 DEVICE_TITLE := ZyXEL NBG6617 ROOTFS_SIZE := 24960k RAS_BOARD := NBG6617 RAS_ROOTFS_SIZE := 19840k RAS_VERSION := "$(VERSION_DIST) $(REVISION)" IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata IMAGES := sysupgrade.bin factory.bin # The ZyXEL firmware allows flashing thru the web-gui only when the rootfs is # at least as large as the one of the initial firmware image (not the current # one on the device). This only applies to the Web-UI, the bootlaoder ignores # this minimum-size. However, the larger image can be flashed both ways. IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k | check-size $$$$(ROOTFS_SIZE) | zyxel-ras-image separate-kernel IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-rootfs | check-size $$$$(ROOTFS_SIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata DEVICE_PACKAGES := uboot-envtools kmod-usb-ledtrig-usbport endef TARGET_DEVICES += zyxel_nbg6617 define Device/zyxel_wre6606 $(call Device/FitImage) DEVICE_TITLE := ZyXEL WRE6606 DEVICE_DTS_CONFIG := config@4 DEVICE_DTS := qcom-ipq4018-wre6606 IMAGES := sysupgrade.bin IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata endef TARGET_DEVICES += zyxel_wre6606 $(eval $(call BuildImage))