#include "vr9.dtsi"

#include <dt-bindings/input/input.h>
#include <dt-bindings/mips/lantiq_rcu_gphy.h>

/ {
	compatible = "arcadyan,vgv7510kw22", "lantiq,xway", "lantiq,vr9";

	chosen {
		bootargs = "console=ttyLTQ0,115200 mem=62M vpe1_load_addr=0x83e00000 vpe1_mem=2M maxvpes=1 maxtcs=1 nosmp";
	};

	aliases {
		led-boot = &power_green;
		led-failsafe = &power_red;
		led-running = &power_green;
		led-upgrade = &power_green;

		led-dsl = &dsl;
		led-internet = &internet_green;
		led-wifi = &wifi;
	};

	memory@0 {
		device_type = "memory";
		reg = <0x0 0x4000000>;
	};

	keys {
		compatible = "gpio-keys-polled";
		poll-interval = <100>;

		reset {
			label = "reset";
			gpios = <&gpio 6 GPIO_ACTIVE_LOW>;
			linux,code = <KEY_RESTART>;
		};

		wps {
			label = "wps";
			gpios = <&gpio 9 GPIO_ACTIVE_LOW>;
			linux,code = <KEY_WPS_BUTTON>;
		};
	};

	leds {
		compatible = "gpio-leds";

		dsl: dsl {
			label = "green:dsl";
			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
		};

		internet_red {
			label = "red:internet";
			gpios = <&gpio 10 GPIO_ACTIVE_LOW>;
		};

		info_red {
			label = "red:info";
			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
		};

		power_green: power {
			label = "green:power";
			gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
			default-state = "keep";
		};

		info_green {
			label = "green:info";
			gpios = <&gpio 15 GPIO_ACTIVE_LOW>;
		};

		internet_green: internet_green {
			label = "green:internet";
			gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
		};

		wifi: wifi {
			label = "green:wlan";
			gpios = <&gpio 20 GPIO_ACTIVE_LOW>;
		};

		power_red: power2 {
			label = "red:power";
			gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
		};

		phone {
			label = "green:telefon";
			gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
		};
	};

	usb_vbus: regulator-usb-vbus {
		compatible = "regulator-fixed";

		regulator-name = "USB_VBUS";

		regulator-min-microvolt = <5000000>;
		regulator-max-microvolt = <5000000>;

		gpio = <&gpio 47 GPIO_ACTIVE_HIGH>;
		enable-active-high;
	};
};

&eth0 {
	mtd-mac-address = <&boardconfig 0x16>;
};

&gphy0 {
	lantiq,gphy-mode = <GPHY_MODE_FE>;
};

&gphy1 {
	lantiq,gphy-mode = <GPHY_MODE_FE>;
};

&gpio {
	pinctrl-names = "default";
	pinctrl-0 = <&state_default>, <&gphy0_led1_pins>;

	state_default: pinmux {
		pci-rst {
			lantiq,pins = "io21";
			lantiq,open-drain = <0>;
			lantiq,pull = <0>;
			lantiq,output = <1>;
		};
	};
};

&gswip {
	pinctrl-0 = <&mdio_pins>,
		    <&gphy0_led0_pins>,
		    <&gphy1_led0_pins>, <&gphy1_led1_pins>;
	pinctrl-names = "default";
};

&gswip_mdio {
	phy1: ethernet-phy@1 {
		reg = <0x1>;
	};
	phy11: ethernet-phy@11 {
		reg = <0x11>;
	};
	phy12: ethernet-phy@12 {
		reg = <0x12>;
	};
	phy13: ethernet-phy@13 {
		reg = <0x13>;
	};
	phy14: ethernet-phy@14 {
		reg = <0x14>;
	};
};

&gswip_ports {
	port@0 {
		reg = <0>;
		label = "wan";
		phy-mode = "mii";
		phy-handle = <&phy1>;
	};
	port@2 {
		reg = <2>;
		label = "lan2";
		phy-mode = "internal";
		phy-handle = <&phy11>;
	};
	port@3 {
		reg = <3>;
		label = "lan1";
		phy-mode = "internal";
		phy-handle = <&phy12>;
	};
	port@4 {
		reg = <4>;
		label = "lan4";
		phy-mode = "internal";
		phy-handle = <&phy13>;
	};
	port@5 {
		reg = <5>;
		label = "lan3";
		phy-mode = "internal";
		phy-handle = <&phy14>;
	};
};

&localbus {
	flash@0 {
		compatible = "lantiq,nor";
		bank-width = <2>;
		reg = <0 0x0 0x1000000>;

		partitions {
			compatible = "fixed-partitions";
			#address-cells = <1>;
			#size-cells = <1>;

			boardconfig: partition@fe0000 {
				label = "board_config";
				reg = <0xfe0000 0x20000>;
				read-only;
			};
		};
	};
};

&pci0 {
	status = "okay";
	gpio-reset = <&gpio 21 GPIO_ACTIVE_HIGH>;

	wifi@1814,3592 {
		compatible = "pci1814,3592";
		reg = <0x7000 0 0 0 0>;
		ralink,mtd-eeprom = <&boardconfig 0x410>;
		ralink,mtd-eeprom-swap;
		mtd-mac-address = <&boardconfig 0x16>;
		mac-address-increment = <1>;
	};
};

&pcie0 {
	status = "disabled";
};

&usb_phy0 {
	status = "okay";
};

&usb0 {
	status = "okay";
	vbus-supply = <&usb_vbus>;
};

&vmmc {
	status = "okay";
	gpios = <&gpio 30 GPIO_ACTIVE_HIGH  //fxs relay
			 &gpio 31 GPIO_ACTIVE_HIGH  //still unknown
			 &gpio 3  GPIO_ACTIVE_HIGH>; //reset_slic?
};