--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+#include <common.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/ddr.h>
+#include <asm/arch/ubus4.h>
+#include <spl.h>
+#if defined(CONFIG_BCMBCA_PMC)
+#include "pmc_drv.h"
+#include "asm/arch/BPCM.h"
+#endif
+
+#if defined(CONFIG_TPL_BUILD)
+static void enable_ns_access(void)
+{
+ BIUCFG->bac.bac_permission |= 0x33; // Linux access to BAC_CPU_THERM_TEMP
+}
+
+/*this function is used to turn on CCI from secure mode
+* * it also turns snooping enable for S5 CPU interface*/
+static void cci500_enable(void)
+{
+ /*Enable access from E2 and below */
+ CCI500->secr_acc |= SECURE_ACCESS_UNSECURE_ENABLE;
+}
+#endif
+
+#if !defined(CONFIG_SPL_BUILD)
+void print_chipinfo(void)
+{
+ unsigned int chipId = (PERF->RevID & CHIP_ID_MASK) >> CHIP_ID_SHIFT;
+ unsigned int revId = PERF->RevID & REV_ID_MASK;
+
+ printf("Chip ID: BCM%X_%X\n",chipId,revId);
+}
+#endif
+
+#if defined(CONFIG_BCMBCA_PMC)
+
+void boost_cpu_clock(void)
+{
+ printf("set cpu freq to 1700MHz\n");
+ set_cpu_freq(1700);
+ pll_ch_freq_set(PMB_ADDR_BIU_PLL, 1, 3000/600); // raise ACEBIU clock rate to 600 MHz
+}
+
+int set_cpu_freq(int freqMHz)
+{
+ int mdiv;
+
+ if( freqMHz > 1700 || freqMHz < 485 )
+ {
+ printf("%dMHz is not supported\n", freqMHz);
+ return -1;
+ }
+
+ /* VCO at 3.4GHz, mdiv = Fvco/target frequency */
+ mdiv = 3400/freqMHz;
+
+ pll_ch_freq_set(PMB_ADDR_BIU_PLL, 0, mdiv);
+
+ return 3400/mdiv;
+}
+#endif
+
+int bcmbca_get_boot_device(void)
+{
+ if ((MISC->miscStrapBus&MISC_STRAP_BUS_BOOT_SEL_NAND_MASK) == MISC_STRAP_BUS_BOOT_NAND)
+ return BOOT_DEVICE_NAND;
+
+ if ((MISC->miscStrapBus&MISC_STRAP_BUS_BOOT_SEL_MASK) == MISC_STRAP_BUS_BOOT_SPI_NAND)
+ return BOOT_DEVICE_SPI;
+
+ if ((MISC->miscStrapBus&MISC_STRAP_BUS_BOOT_SEL_MASK) == MISC_STRAP_BUS_BOOT_EMMC)
+ return BOOT_DEVICE_MMC1;
+
+ printf("Error: boot_sel straps are not set correctly\n");
+
+ return BOOT_DEVICE_NONE;
+}
+
+int arch_cpu_init(void)
+{
+#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_TPL_BUILD)
+
+ u32 frq = COUNTER_FREQUENCY;
+
+ spl_ddrinit_prepare();
+
+ /* set arch timer frequency */
+ asm volatile("mcr p15, 0, %0, c14, c0, 0" : : "r" (frq));
+ /* enable system timer */
+ BIUCFG->TSO_CNTCR |= 1;
+
+ /* enable unalgined access */
+ set_cr(get_cr() & ~CR_A);
+#endif
+
+#if defined(CONFIG_TPL_BUILD)
+ enable_ns_access();
+ cci500_enable();
+#endif
+
+
+ return 0;
+}
+
+void arch_cpu_deinit()
+{
+}
+
+int get_nr_cpus()
+{
+ uint32_t nr_cpus;
+
+ if (bcm_otp_get_nr_cpus(&nr_cpus)) {
+ printf("Error: failed to read cpu core from OTP\n");
+ nr_cpus = 4;
+ } else {
+ if (nr_cpus >= 0 && nr_cpus <= 4)
+ nr_cpus = 4;
+ else
+ nr_cpus = 8 - nr_cpus;
+ }
+
+ return nr_cpus;
+}
+
+#if !defined(CONFIG_TPL_ATF)
+void boot_secondary_cpu(unsigned long vector)
+{
+ uint32_t cpu = 1;
+ uint32_t nr_cpus = get_nr_cpus();
+ ARM_CONTROL_REG ctrl_reg;
+
+ printf("boot secondary cpu from 0x%lx\n", vector);
+
+ *(volatile uint32_t*)(BOOTLUT_BASE+0x20) = vector;
+
+ while (cpu < nr_cpus) {
+ int stat;
+
+ stat = PowerOnDevice(PMB_ADDR_ORION_CPU0 + cpu);
+ if (stat != kPMC_NO_ERROR)
+ printf("failed to power on secondary cpu %d - sts %d\n", cpu, stat);
+
+ stat = ReadBPCMRegister(PMB_ADDR_BIU_BPCM, ARMBPCMRegOffset(arm_control), &ctrl_reg.Reg32);
+ ctrl_reg.Bits.cpu_reset_n &= ~(0x1 << cpu);
+ stat |= WriteBPCMRegister(PMB_ADDR_BIU_BPCM, ARMBPCMRegOffset(arm_control), ctrl_reg.Reg32);
+ if (stat != kPMC_NO_ERROR)
+ printf("failed to boot secondary cpu %d - sts %d\n", cpu, stat);
+
+ cpu++;
+ }
+
+ return;
+}
+#endif