config BUSYBOX_CONFIG_ADJTIMEX
bool "adjtimex (4.7 kb)"
default BUSYBOX_DEFAULT_ADJTIMEX
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Adjtimex reads and optionally sets adjustment parameters for
the Linux clock adjustment algorithm.
config BUSYBOX_CONFIG_BEEP
bool "beep (2.4 kb)"
default BUSYBOX_DEFAULT_BEEP
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
The beep applets beeps in a given freq/Hz.
config BUSYBOX_CONFIG_CONSPY
bool "conspy (10 kb)"
default BUSYBOX_DEFAULT_CONSPY
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
A text-mode VNC like program for Linux virtual terminals.
example: conspy NUM shared access to console num
config BUSYBOX_CONFIG_DEVFSD
bool "devfsd (obsolete)"
default BUSYBOX_DEFAULT_DEVFSD
- select BUSYBOX_CONFIG_PLATFORM_LINUX
select BUSYBOX_CONFIG_FEATURE_SYSLOG
help
This is deprecated and should NOT be used anymore.
config BUSYBOX_CONFIG_FEATURE_DEVFS
bool "Use devfs names for all devices (obsolete)"
default BUSYBOX_DEFAULT_FEATURE_DEVFS
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
This is obsolete and should NOT be used anymore.
Use linux >= 2.6 (optionally with hotplug) and mdev instead!
config BUSYBOX_CONFIG_FBSPLASH
bool "fbsplash (26 kb)"
default BUSYBOX_DEFAULT_FBSPLASH
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Shows splash image and progress bar on framebuffer device.
Can be used during boot phase of an embedded device.
config BUSYBOX_CONFIG_HDPARM
bool "hdparm (25 kb)"
default BUSYBOX_DEFAULT_HDPARM
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Get/Set hard drive parameters. Primarily intended for ATA
drives.
config BUSYBOX_CONFIG_I2CGET
bool "i2cget (5.5 kb)"
default BUSYBOX_DEFAULT_I2CGET
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Read from I2C/SMBus chip registers.
config BUSYBOX_CONFIG_I2CSET
bool "i2cset (6.7 kb)"
default BUSYBOX_DEFAULT_I2CSET
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Set I2C registers.
config BUSYBOX_CONFIG_I2CDUMP
bool "i2cdump (7.1 kb)"
default BUSYBOX_DEFAULT_I2CDUMP
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Examine I2C registers.
config BUSYBOX_CONFIG_I2CDETECT
bool "i2cdetect (7.1 kb)"
default BUSYBOX_DEFAULT_I2CDETECT
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Detect I2C chips.
config BUSYBOX_CONFIG_I2CTRANSFER
bool "i2ctransfer (4.0 kb)"
default BUSYBOX_DEFAULT_I2CTRANSFER
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Send user-defined I2C messages in one transfer.
config BUSYBOX_CONFIG_LSSCSI
bool "lsscsi (2.5 kb)"
default BUSYBOX_DEFAULT_LSSCSI
- #select PLATFORM_LINUX
help
lsscsi is a utility for displaying information about SCSI buses in the
system and devices connected to them.
default BUSYBOX_DEFAULT_MICROCOM
help
The poor man's minicom utility for chatting with serial port devices.
+config BUSYBOX_CONFIG_MIM
+ bool "mim (0.5 kb)"
+ default BUSYBOX_DEFAULT_MIM
+ depends on BUSYBOX_CONFIG_FEATURE_SH_EMBEDDED_SCRIPTS
+ help
+ Run a script from a Makefile-like specification file.
+ Unlike 'make' dependencies aren't supported.
config BUSYBOX_CONFIG_MT
bool "mt (2.5 kb)"
default BUSYBOX_DEFAULT_MT
config BUSYBOX_CONFIG_NANDWRITE
bool "nandwrite (4.8 kb)"
default BUSYBOX_DEFAULT_NANDWRITE
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Write to the specified MTD device, with bad blocks awareness
config BUSYBOX_CONFIG_NANDDUMP
bool "nanddump (5.2 kb)"
default BUSYBOX_DEFAULT_NANDDUMP
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Dump the content of raw NAND chip
config BUSYBOX_CONFIG_PARTPROBE
bool "partprobe (3.5 kb)"
default BUSYBOX_DEFAULT_PARTPROBE
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Ask kernel to rescan partition table.
config BUSYBOX_CONFIG_RAIDAUTORUN
bool "raidautorun (1.3 kb)"
default BUSYBOX_DEFAULT_RAIDAUTORUN
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
raidautorun tells the kernel md driver to
search and start RAID arrays.
bool "readahead (1.5 kb)"
default BUSYBOX_DEFAULT_READAHEAD
depends on BUSYBOX_CONFIG_LFS
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Preload the files listed on the command line into RAM cache so that
subsequent reads on these files will not block on disk I/O.
config BUSYBOX_CONFIG_RFKILL
bool "rfkill (4.4 kb)"
default BUSYBOX_DEFAULT_RFKILL # doesn't build on Ubuntu 9.04
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Enable/disable wireless devices.
config BUSYBOX_CONFIG_RX
bool "rx (2.9 kb)"
default BUSYBOX_DEFAULT_RX
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Receive files using the Xmodem protocol.
config BUSYBOX_CONFIG_SETFATTR
config BUSYBOX_CONFIG_SETSERIAL
bool "setserial (6.9 kb)"
default BUSYBOX_DEFAULT_SETSERIAL
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Retrieve or set Linux serial port.
config BUSYBOX_CONFIG_STRINGS
config BUSYBOX_CONFIG_UBIATTACH
bool "ubiattach (4.2 kb)"
default BUSYBOX_DEFAULT_UBIATTACH
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Attach MTD device to an UBI device.
config BUSYBOX_CONFIG_UBIDETACH
bool "ubidetach (4.1 kb)"
default BUSYBOX_DEFAULT_UBIDETACH
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Detach MTD device from an UBI device.
config BUSYBOX_CONFIG_UBIMKVOL
bool "ubimkvol (5.3 kb)"
default BUSYBOX_DEFAULT_UBIMKVOL
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Create a UBI volume.
config BUSYBOX_CONFIG_UBIRMVOL
bool "ubirmvol (4.9 kb)"
default BUSYBOX_DEFAULT_UBIRMVOL
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Delete a UBI volume.
config BUSYBOX_CONFIG_UBIRSVOL
bool "ubirsvol (4.2 kb)"
default BUSYBOX_DEFAULT_UBIRSVOL
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Resize a UBI volume.
config BUSYBOX_CONFIG_UBIUPDATEVOL
bool "ubiupdatevol (5.2 kb)"
default BUSYBOX_DEFAULT_UBIUPDATEVOL
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Update a UBI volume.
config BUSYBOX_CONFIG_UBIRENAME
bool "ubirename (2.4 kb)"
default BUSYBOX_DEFAULT_UBIRENAME
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
Utility to rename UBI volumes
config BUSYBOX_CONFIG_VOLNAME
config BUSYBOX_CONFIG_WATCHDOG
bool "watchdog (5.3 kb)"
default BUSYBOX_DEFAULT_WATCHDOG
- select BUSYBOX_CONFIG_PLATFORM_LINUX
help
The watchdog utility is used with hardware or software watchdog
device drivers. It opens the specified watchdog device special file
projects / openwrt / staging / mkresin.git / blobdiff