ath79: fix boardname of GL.iNet GL-AR150

[openwrt/openwrt.git] / target / linux / ath79 / dts / ar9330_glinet_ar150.dts

diff --git a/target/linux/ath79/dts/ar9330_glinet_ar150.dts b/target/linux/ath79/dts/ar9330_glinet_ar150.dts
deleted file mode 100644 (file)
index fbc3acd..0000000
--- a/target/linux/ath79/dts/ar9330_glinet_ar150.dts
+++ /dev/null
@@ -1,145 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-#include "ar9330.dtsi"
-
-/ {
-       model = "GL.iNet GL-AR150";
-       compatible = "glinet,ar150", "qca,ar9330";
-
-       aliases {
-               serial0 = &uart;
-               led-boot = &wlan;
-               led-failsafe = &wlan;
-               led-upgrade = &wlan;
-       };
-
-       leds {
-               compatible = "gpio-leds";
-
-               wlan: wlan {
-                       label = "gl-ar150:orange:wlan";
-                       gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
-                       linux,default-trigger = "phy0tpt";
-               };
-
-               lan {
-                       label = "gl-ar150:green:lan";
-                       gpios = <&gpio 13 GPIO_ACTIVE_HIGH>;
-               };
-
-               wan {
-                       label = "gl-ar150:green:wan";
-                       gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
-               };
-       };
-
-       keys {
-               compatible = "gpio-keys-polled";
-               poll-interval = <100>;
-
-               manual {
-                       label = "manual";
-                       linux,code = <BTN_7>;
-                       gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
-               };
-
-               auto {
-                       label = "auto";
-                       linux,code = <BTN_8>;
-                       gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
-               };
-
-               reset {
-                       label = "reset";
-                       linux,code = <KEY_RESTART>;
-                       gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
-               };
-       };
-};
-
-&uart {
-       status = "okay";
-};
-
-&gpio {
-       status = "okay";
-};
-
-&usb {
-       dr_mode = "host";
-       status = "okay";
-};
-
-&usb_phy {
-       status = "okay";
-       gpios = <&gpio 6 GPIO_ACTIVE_HIGH>;
-};
-
-&spi {
-       num-chipselects = <1>;
-       status = "okay";
-
-       flash@0 {
-               compatible = "jedec,spi-nor";
-               spi-max-frequency = <104000000>;
-               reg = <0>;
-
-               partitions {
-                       compatible = "fixed-partitions";
-                       #address-cells = <1>;
-                       #size-cells = <1>;
-
-                       partition@0 {
-                               label = "u-boot";
-                               reg = <0x000000 0x040000>;
-                               read-only;
-                       };
-
-                       partition@1 {
-                               label = "u-boot-env";
-                               reg = <0x040000 0x010000>;
-                       };
-
-                       partition@2 {
-                               compatible = "denx,uimage";
-                               label = "firmware";
-                               reg = <0x050000 0xfa0000>;
-                       };
-
-                       art: partition@3 {
-                               label = "ART";
-                               reg = <0xff0000 0x010000>;
-                               read-only;
-                       };
-               };
-       };
-};
-
-&eth0 {
-       status = "okay";
-
-       mtd-mac-address = <&art 0x0>;
-};
-
-&eth1 {
-       status = "okay";
-
-       mtd-mac-address = <&art 0x0>;
-
-       gmac-config {
-               device = <&gmac>;
-
-               switch-phy-addr-swap = <0>;
-               switch-phy-swap = <0>;
-       };
-};
-
-&wmac {
-       status = "okay";
-       mtd-cal-data = <&art 0x1000>;
-       mtd-mac-address = <&art 0x0>;
-};