--- /dev/null
+#ifndef __AR531X_H
+#define __AR531X_H
+
+#include <ar531x_platform.h>
+#include "ar5312.h"
+#include "ar5315.h"
+
+#define MIPS_CPU_IRQ_BASE 0x00
+#define AR531X_HIGH_PRIO 0x10
+#define AR531X_MISC_IRQ_BASE 0x20
+#define AR531X_GPIO_IRQ_BASE 0x30
+
+/* Software's idea of interrupts handled by "CPU Interrupt Controller" */
+#define AR531X_IRQ_NONE MIPS_CPU_IRQ_BASE+0
+#define AR531X_IRQ_CPU_CLOCK MIPS_CPU_IRQ_BASE+7 /* C0_CAUSE: 0x8000 */
+
+/* Miscellaneous interrupts, which share IP6 */
+#define AR531X_MISC_IRQ_NONE AR531X_MISC_IRQ_BASE+0
+#define AR531X_MISC_IRQ_TIMER AR531X_MISC_IRQ_BASE+1
+#define AR531X_MISC_IRQ_AHB_PROC AR531X_MISC_IRQ_BASE+2
+#define AR531X_MISC_IRQ_AHB_DMA AR531X_MISC_IRQ_BASE+3
+#define AR531X_MISC_IRQ_GPIO AR531X_MISC_IRQ_BASE+4
+#define AR531X_MISC_IRQ_UART0 AR531X_MISC_IRQ_BASE+5
+#define AR531X_MISC_IRQ_UART0_DMA AR531X_MISC_IRQ_BASE+6
+#define AR531X_MISC_IRQ_WATCHDOG AR531X_MISC_IRQ_BASE+7
+#define AR531X_MISC_IRQ_LOCAL AR531X_MISC_IRQ_BASE+8
+#define AR531X_MISC_IRQ_COUNT 9
+
+/* GPIO Interrupts [0..7], share AR531X_MISC_IRQ_GPIO */
+#define AR531X_GPIO_IRQ_NONE AR531X_MISC_IRQ_BASE+0
+#define AR531X_GPIO_IRQ(n) AR531X_MISC_IRQ_BASE+(n)+1
+#define AR531X_GPIO_IRQ_COUNT 22
+
+#define sysRegRead(phys) \
+ (*(volatile u32 *)KSEG1ADDR(phys))
+
+#define sysRegWrite(phys, val) \
+ ((*(volatile u32 *)KSEG1ADDR(phys)) = (val))
+
+/*
+ * This is board-specific data that is stored in a "fixed" location in flash.
+ * It is shared across operating systems, so it should not be changed lightly.
+ * The main reason we need it is in order to extract the ethernet MAC
+ * address(es).
+ */
+struct ar531x_boarddata {
+ u32 magic; /* board data is valid */
+#define AR531X_BD_MAGIC 0x35333131 /* "5311", for all 531x platforms */
+ u16 cksum; /* checksum (starting with BD_REV 2) */
+ u16 rev; /* revision of this struct */
+#define BD_REV 4
+ char boardName[64]; /* Name of board */
+ u16 major; /* Board major number */
+ u16 minor; /* Board minor number */
+ u32 config; /* Board configuration */
+#define BD_ENET0 0x00000001 /* ENET0 is stuffed */
+#define BD_ENET1 0x00000002 /* ENET1 is stuffed */
+#define BD_UART1 0x00000004 /* UART1 is stuffed */
+#define BD_UART0 0x00000008 /* UART0 is stuffed (dma) */
+#define BD_RSTFACTORY 0x00000010 /* Reset factory defaults stuffed */
+#define BD_SYSLED 0x00000020 /* System LED stuffed */
+#define BD_EXTUARTCLK 0x00000040 /* External UART clock */
+#define BD_CPUFREQ 0x00000080 /* cpu freq is valid in nvram */
+#define BD_SYSFREQ 0x00000100 /* sys freq is set in nvram */
+#define BD_WLAN0 0x00000200 /* Enable WLAN0 */
+#define BD_MEMCAP 0x00000400 /* CAP SDRAM @ memCap for testing */
+#define BD_DISWATCHDOG 0x00000800 /* disable system watchdog */
+#define BD_WLAN1 0x00001000 /* Enable WLAN1 (ar5212) */
+#define BD_ISCASPER 0x00002000 /* FLAG for AR2312 */
+#define BD_WLAN0_2G_EN 0x00004000 /* FLAG for radio0_2G */
+#define BD_WLAN0_5G_EN 0x00008000 /* FLAG for radio0_2G */
+#define BD_WLAN1_2G_EN 0x00020000 /* FLAG for radio0_2G */
+#define BD_WLAN1_5G_EN 0x00040000 /* FLAG for radio0_2G */
+ u16 resetConfigGpio; /* Reset factory GPIO pin */
+ u16 sysLedGpio; /* System LED GPIO pin */
+
+ u32 cpuFreq; /* CPU core frequency in Hz */
+ u32 sysFreq; /* System frequency in Hz */
+ u32 cntFreq; /* Calculated C0_COUNT frequency */
+
+ u8 wlan0Mac[6];
+ u8 enet0Mac[6];
+ u8 enet1Mac[6];
+
+ u16 pciId; /* Pseudo PCIID for common code */
+ u16 memCap; /* cap bank1 in MB */
+
+ /* version 3 */
+ u8 wlan1Mac[6]; /* (ar5212) */
+};
+
+
+extern char *board_config;
+extern char *radio_config;
+extern void serial_setup(unsigned long mapbase, unsigned int uartclk);
+extern int ar531x_find_config(char *flash_limit);
+
+extern void ar5312_misc_intr_init(int irq_base);
+extern void ar5312_irq_dispatch(void);
+extern void ar5312_plat_setup(void);
+
+extern void ar5315_misc_intr_init(int irq_base);
+extern asmlinkage void ar5315_irq_dispatch(void);
+extern void ar5315_plat_setup(void);
+
+#endif
projects / openwrt / staging / florian.git / blobdiff