bcm63xx: drop kernel 5.10 support

[openwrt/staging/noltari.git] / target / linux / bcm63xx / patches-5.10 / 531-board_bcm6348-bt-voyager-2500v-bb.patch

diff --git a/target/linux/bcm63xx/patches-5.10/531-board_bcm6348-bt-voyager-2500v-bb.patch b/target/linux/bcm63xx/patches-5.10/531-board_bcm6348-bt-voyager-2500v-bb.patch
deleted file mode 100644 (file)
index 39728c4..0000000
--- a/target/linux/bcm63xx/patches-5.10/531-board_bcm6348-bt-voyager-2500v-bb.patch
+++ /dev/null
@@ -1,49 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -3230,6 +3230,22 @@ void __init board_bcm963xx_init(void)
-               val &= MPI_CSBASE_BASE_MASK;
-       }
-       boot_addr = (u8 *)KSEG1ADDR(val);
-+      pr_info("Boot address 0x%08x\n",(unsigned int)boot_addr);
-+
-+      /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
-+      /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
-+      /* Loading firmware from the CFE Prompt always loads to Bank 0 */
-+      /* Do an early check of CFE and then select bank 0 */
-+
-+      if (boot_addr == (u8 *)0xbf800000) {
-+              u8 *tmp_boot_addr = (u8*)0xbfc00000;
-+
-+              bcm63xx_nvram_init(tmp_boot_addr + BCM963XX_NVRAM_OFFSET);
-+              if (!strcmp(bcm63xx_nvram_get_name(), "V2500V_BB")) {
-+                      pr_info("V2500V: nvram bank 0\n");
-+                      boot_addr = tmp_boot_addr;
-+              }
-+      }
- 
-       /* dump cfe version */
-       cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
---- a/arch/mips/bcm63xx/dev-flash.c
-+++ b/arch/mips/bcm63xx/dev-flash.c
-@@ -21,6 +21,7 @@
- #include <linux/spi/spi.h>
- #include <linux/spi/flash.h>
- 
-+#include <bcm63xx_board.h>
- #include <bcm63xx_cpu.h>
- #include <bcm63xx_dev_flash.h>
- #include <bcm63xx_regs.h>
-@@ -256,6 +257,13 @@ int __init bcm63xx_flash_register(void)
-                       val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-                       val &= MPI_CSBASE_BASE_MASK;
- 
-+                      /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
-+                      /* Loading from CFE always uses Bank 0 */
-+                      if (!strcmp(board_get_name(), "V2500V_BB")) {
-+                              pr_info("V2500V: Start in Bank 0\n");
-+                              val = val + 0x400000; // Select Bank 0 start address
-+                      }
-+
-                       mtd_resources[0].start = val;
-                       mtd_resources[0].end = 0x1FFFFFFF;
-               }