remove the brcm-2.4 target, it will no longer be supported in future releases. please...

[openwrt/svn-archive/archive.git] / target / linux / brcm-2.4 / patches / 012-aec62xx.patch

diff --git a/target/linux/brcm-2.4/patches/012-aec62xx.patch b/target/linux/brcm-2.4/patches/012-aec62xx.patch
deleted file mode 100644 (file)
index 7010daf..0000000
--- a/target/linux/brcm-2.4/patches/012-aec62xx.patch
+++ /dev/null
@@ -1,100 +0,0 @@
---- a/drivers/ide/pci/aec62xx.c
-+++ b/drivers/ide/pci/aec62xx.c
-@@ -3,6 +3,8 @@
-  *
-  * Copyright (C) 1999-2002    Andre Hedrick <andre@linux-ide.org>
-  *
-+ * With Broadcom 4780 patches
-+ *
-  */
- 
- #include <linux/module.h>
-@@ -329,7 +331,11 @@ static int aec62xx_config_drive_xfer_rat
-       ide_hwif_t *hwif        = HWIF(drive);
-       struct hd_driveid *id   = drive->id;
- 
-+#ifndef CONFIG_BCM947XX
-       if ((id->capability & 1) && drive->autodma) {
-+#else
-+      if (1) {
-+#endif
-               /* Consult the list of known "bad" drives */
-               if (hwif->ide_dma_bad_drive(drive))
-                       goto fast_ata_pio;
-@@ -414,10 +420,60 @@ static unsigned int __init init_chipset_
- {
-       int bus_speed = system_bus_clock();
- 
-+#ifndef CONFIG_BCM947XX
-       if (dev->resource[PCI_ROM_RESOURCE].start) {
-               pci_write_config_dword(dev, PCI_ROM_ADDRESS, dev->resource[PCI_ROM_RESOURCE].start | PCI_ROM_ADDRESS_ENABLE);
-               printk(KERN_INFO "%s: ROM enabled at 0x%08lx\n", name, dev->resource[PCI_ROM_RESOURCE].start);
-       }
-+#else
-+      if (dev->resource[PCI_ROM_RESOURCE].start) {
-+              pci_write_config_dword(dev, PCI_ROM_ADDRESS,
-+                                      dev->resource[PCI_ROM_RESOURCE].
-+                                      start | PCI_ROM_ADDRESS_ENABLE);
-+      } else {
-+              pci_write_config_dword(dev, PCI_ROM_ADDRESS,
-+                                      dev->resource[PCI_ROM_RESOURCE].
-+                                      start);
-+      }
-+
-+      /* Set IDE controller parameters manually - FIXME: replace magic values */
-+      {
-+              byte setting;
-+
-+              pci_write_config_word(dev, PCI_COMMAND, 0x0007);
-+              //pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x5A);
-+              pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x13);
-+
-+              pci_write_config_byte(dev, 0x40, 0x31);
-+              pci_write_config_byte(dev, 0x41, 0x31);
-+              pci_write_config_byte(dev, 0x42, 0x31);
-+              pci_write_config_byte(dev, 0x43, 0x31);
-+              // Set IDE Command Speed
-+              pci_write_config_byte(dev, 0x48, 0x31);
-+
-+              // Disable WriteSubSysID & PIOROM
-+              pci_read_config_byte(dev, 0x49, &setting);
-+              setting &= 0x07;
-+              pci_write_config_byte(dev, 0x49, setting);
-+
-+              // Enable PCI burst & INTA & PCI memory read multiple, FIFO threshold=80
-+              pci_read_config_byte(dev, 0x4A, &setting);
-+              //setting = (setting & 0xFE) | 0xA8;
-+              setting = (setting & 0xFE) | 0xD8;
-+              setting = (setting & 0xF7);
-+              pci_write_config_byte(dev, 0x4A, setting);
-+
-+              //pci_write_config_byte(dev, 0x4B, 0x20);
-+              pci_write_config_byte(dev, 0x4B, 0x2C);
-+              //pci_write_config_byte(dev, 0x4B, 0x0C);
-+
-+              // Set PreRead count: 512 byte
-+              pci_write_config_byte(dev, 0x4C, 0);
-+              pci_write_config_word(dev, 0x4D, 0x0002);
-+              pci_write_config_byte(dev, 0x54, 0);
-+              pci_write_config_word(dev, 0x55, 0x0002);
-+      }
-+#endif
- 
- #if defined(DISPLAY_AEC62XX_TIMINGS) && defined(CONFIG_PROC_FS)
-       aec_devs[n_aec_devs++] = dev;
-@@ -500,6 +556,7 @@ static void __init init_setup_aec62xx (s
- 
- static void __init init_setup_aec6x80 (struct pci_dev *dev, ide_pci_device_t *d)
- {
-+#ifndef CONFIG_BCM947XX /* Causes OOPS on BCM4780 */
-       unsigned long bar4reg = pci_resource_start(dev, 4);
- 
-       if (inb(bar4reg+2) & 0x10) {
-@@ -512,6 +569,7 @@ static void __init init_setup_aec6x80 (s
-                       strcpy(d->name, "AEC6280R");
-       }
- 
-+#endif
-       ide_setup_pci_device(dev, d);
- }
-