brcm2708: remove linux 4.4 support

[openwrt/staging/yousong.git] / target / linux / brcm2708 / patches-4.4 / 0201-Add-overlay-and-enable-support-for-QCA7000-board.patch

diff --git a/target/linux/brcm2708/patches-4.4/0201-Add-overlay-and-enable-support-for-QCA7000-board.patch b/target/linux/brcm2708/patches-4.4/0201-Add-overlay-and-enable-support-for-QCA7000-board.patch
deleted file mode 100644 (file)
index 7576f61..0000000
--- a/target/linux/brcm2708/patches-4.4/0201-Add-overlay-and-enable-support-for-QCA7000-board.patch
+++ /dev/null
@@ -1,127 +0,0 @@
-From 358feb7def17978e9a3c45c1971b42d36ff89545 Mon Sep 17 00:00:00 2001
-From: Michael Heimpold <michael.heimpold@i2se.com>
-Date: Fri, 29 Jan 2016 12:00:37 +0100
-Subject: [PATCH] Add overlay and enable support for QCA7000 board
-
-This adds a device tree overlay for the QCA7000 which can be used
-when attaching an I2SE's PLC Stamp micro EVK to the Raspberry Pi.
-
-This Evaluation Board embeds a QCA7000 chip, a Homeplug Green PHY
-powerline chip from Qualcomm/Atheros for the Internet of Things.
-
-This patch also enables the required QCA7000 driver module
-in the default configurations.
-
-Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
-Signed-off-by: Michael Heimpold <michael.heimpold@i2se.com>
----
- arch/arm/boot/dts/overlays/Makefile            |  1 +
- arch/arm/boot/dts/overlays/README              |  8 ++++
- arch/arm/boot/dts/overlays/qca7000-overlay.dts | 52 ++++++++++++++++++++++++++
- arch/arm/configs/bcm2709_defconfig             |  1 +
- arch/arm/configs/bcmrpi_defconfig              |  1 +
- 5 files changed, 63 insertions(+)
- create mode 100644 arch/arm/boot/dts/overlays/qca7000-overlay.dts
-
---- a/arch/arm/boot/dts/overlays/Makefile
-+++ b/arch/arm/boot/dts/overlays/Makefile
-@@ -48,6 +48,7 @@ dtbo-$(RPI_DT_OVERLAYS) += pitft28-resis
- dtbo-$(RPI_DT_OVERLAYS) += pps-gpio.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pwm.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += pwm-2chan.dtbo
-+dtbo-$(RPI_DT_OVERLAYS) += qca7000.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += raspidac3.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += rpi-backlight.dtbo
- dtbo-$(RPI_DT_OVERLAYS) += rpi-dac.dtbo
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -625,6 +625,14 @@ Params: pin                     Output p
-         clock                   PWM clock frequency (informational)
- 
- 
-+Name:   qca7000
-+Info:   I2SE's Evaluation Board for PLC Stamp micro
-+Load:   dtoverlay=qca7000,<param>=<val>
-+Params: int_pin                 GPIO pin for interrupt signal (default 23)
-+
-+        speed                   SPI bus speed (default 12 MHz)
-+
-+
- Name:   raspidac3
- Info:   Configures the RaspiDAV Rev.3x audio card
- Load:   dtoverlay=raspidac3
---- /dev/null
-+++ b/arch/arm/boot/dts/overlays/qca7000-overlay.dts
-@@ -0,0 +1,52 @@
-+// Overlay for the Qualcomm Atheros QCA7000 on I2SE's PLC Stamp micro EVK
-+// Visit: https://www.i2se.com/product/plc-stamp-micro-evk for details
-+
-+/dts-v1/;
-+/plugin/;
-+
-+/ {
-+      compatible = "brcm,bcm2708";
-+
-+      fragment@0 {
-+              target = <&spi0>;
-+              __overlay__ {
-+                      /* needed to avoid dtc warning */
-+                      #address-cells = <1>;
-+                      #size-cells = <0>;
-+
-+                      status = "okay";
-+
-+                      spidev@0 {
-+                              status = "disabled";
-+                      };
-+
-+                      eth1: qca7000@0 {
-+                              compatible = "qca,qca7000";
-+                              reg = <0>; /* CE0 */
-+                              pinctrl-names = "default";
-+                              pinctrl-0 = <&eth1_pins>;
-+                              interrupt-parent = <&gpio>;
-+                              interrupts = <23 0x1>; /* rising edge */
-+                              spi-max-frequency = <12000000>;
-+                              status = "okay";
-+                      };
-+              };
-+      };
-+
-+      fragment@1 {
-+              target = <&gpio>;
-+              __overlay__ {
-+                      eth1_pins: eth1_pins {
-+                              brcm,pins = <23>;
-+                              brcm,function = <0>; /* in */
-+                              brcm,pull = <0>; /* none */
-+                      };
-+              };
-+      };
-+
-+      __overrides__ {
-+              int_pin = <&eth1>, "interrupts:0",
-+                        <&eth1_pins>, "brcm,pins:0";
-+              speed   = <&eth1>, "spi-max-frequency:0";
-+      };
-+};
---- a/arch/arm/configs/bcm2709_defconfig
-+++ b/arch/arm/configs/bcm2709_defconfig
-@@ -446,6 +446,7 @@ CONFIG_NETCONSOLE=m
- CONFIG_TUN=m
- CONFIG_VETH=m
- CONFIG_ENC28J60=m
-+CONFIG_QCA7000=m
- CONFIG_MDIO_BITBANG=m
- CONFIG_PPP=m
- CONFIG_PPP_BSDCOMP=m
---- a/arch/arm/configs/bcmrpi_defconfig
-+++ b/arch/arm/configs/bcmrpi_defconfig
-@@ -439,6 +439,7 @@ CONFIG_NETCONSOLE=m
- CONFIG_TUN=m
- CONFIG_VETH=m
- CONFIG_ENC28J60=m
-+CONFIG_QCA7000=m
- CONFIG_MDIO_BITBANG=m
- CONFIG_PPP=m
- CONFIG_PPP_BSDCOMP=m