renumber patches accordingly

[openwrt/openwrt.git] / target / linux / brcm63xx / patches-2.6.37 / 454-board_V2500V.patch

diff --git a/target/linux/brcm63xx/patches-2.6.37/454-board_V2500V.patch b/target/linux/brcm63xx/patches-2.6.37/454-board_V2500V.patch
deleted file mode 100644 (file)
index 9c4eb89..0000000
--- a/target/linux/brcm63xx/patches-2.6.37/454-board_V2500V.patch
+++ /dev/null
@@ -1,112 +0,0 @@
---- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
-+++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
-@@ -901,6 +901,63 @@ static struct board_info __initdata boar
-       },
- };
- 
-+      static struct board_info __initdata board_V2500V_BB = {
-+        .name                           = "V2500V_BB",
-+        .expected_cpu_id                = 0x6348,
-+
-+        .has_uart0                      = 1,
-+        .has_enet0                      = 1,
-+        .has_enet1                      = 1,
-+        .has_pci                        = 1,
-+
-+        .enet0 = {
-+                .has_phy                = 1,
-+                .use_internal_phy       = 1,
-+        },
-+        .enet1 = {
-+                .force_speed_100        = 1,
-+                .force_duplex_full      = 1,
-+        },
-+
-+      .leds = {
-+              {
-+                      .name           = "power:green",
-+                      .gpio           = 0,
-+                      .active_low     = 1,
-+                      .default_trigger = "default-on",
-+              },
-+              {
-+                      .name           = "power:red",
-+                      .gpio           = 1,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "adsl",
-+                      .gpio           = 2,
-+                      .active_low     = 1,
-+              },
-+              {       .name           = "ppp",
-+                      .gpio           = 3,
-+                      .active_low     = 1,
-+              },
-+              {
-+                      .name           = "wireless",
-+                      .gpio           = 6,
-+                      .active_low     = 1,
-+              },
-+      },
-+      .buttons = {
-+              {
-+                      .desc           = "reset",
-+                      .gpio           = 31,
-+                      .active_low     = 1,
-+                      .type           = EV_KEY,
-+                      .code           = KEY_RESTART,
-+                      .threshold      = 3,
-+              },
-+      },
-+};
-+
- #endif
- 
- /*
-@@ -1953,6 +2010,7 @@ static const struct board_info __initdat
-       &board_spw500v,
-       &board_ct536_ct5621,
-       &board_96348sv,
-+      &board_V2500V_BB,
- #endif
- 
- #ifdef CONFIG_BCM63XX_CPU_6358
-@@ -2101,6 +2159,22 @@ void __init board_prom_init(void)
-               val &= MPI_CSBASE_BASE_MASK;
-       }
-       boot_addr = (u8 *)KSEG1ADDR(val);
-+      printk(KERN_INFO PFX "Boot address 0x%08x\n",(unsigned int)boot_addr);
-+
-+      /* BT Voyager 2500V (RTA1046VW PCB) has 8 Meg flash used as two */
-+      /* banks of 4 Meg. The byte at 0xBF800000 identifies the back to use.*/
-+      /* Loading firmware from the CFE Prompt always loads to Bank 0 */
-+      /* Do an early check of CFE and then select bank 0 */
-+
-+              if (boot_addr == (u8 *)0xbf800000) {
-+              u8 *tmp_boot_addr;
-+              tmp_boot_addr = (u8 *)0xbfc00000; // Address of Bank 0
-+              memcpy(&nvram, tmp_boot_addr + BCM963XX_NVRAM_OFFSET, sizeof(nvram));
-+              if (!strcmp(nvram.name, "V2500V_BB")) {
-+                      printk(KERN_INFO PFX "V2500V: nvram bank 0\n");
-+                      boot_addr = (u8 *)0xbfc00000; // Bank 0
-+              }
-+      }
- 
-       /* dump cfe version */
-       cfe = boot_addr + BCM963XX_CFE_VERSION_OFFSET;
-@@ -2308,6 +2382,14 @@ int __init board_register_devices(void)
-               val = bcm_mpi_readl(MPI_CSBASE_REG(0));
-               val &= MPI_CSBASE_BASE_MASK;
-       }
-+
-+      /* BT Voyager 2500V has 8 Meg flash in two 4 Meg banks */
-+      /* Loading from CFE always uses Bank 0 */
-+      if (!strcmp(board.name, "V2500V_BB")) {
-+              printk(KERN_INFO PFX "V2500V: Start in Bank 0\n");
-+              val = val + 0x400000; // Select Bank 0 start address
-+              }
-+
-       mtd_resources[0].start = val;
-       mtd_resources[0].end = 0x1FFFFFFF;
-