treewide: remove files for building 5.10 kernel

[openwrt/openwrt.git] / target / linux / generic / backport-5.10 / 705-net-phy-at803x-select-correct-page-on-config-init.patch

diff --git a/target/linux/generic/backport-5.10/705-net-phy-at803x-select-correct-page-on-config-init.patch b/target/linux/generic/backport-5.10/705-net-phy-at803x-select-correct-page-on-config-init.patch
deleted file mode 100644 (file)
index 00be403..0000000
--- a/target/linux/generic/backport-5.10/705-net-phy-at803x-select-correct-page-on-config-init.patch
+++ /dev/null
@@ -1,108 +0,0 @@
-From c329e5afb42ff0a88285eb4d8a391a18793e4777 Mon Sep 17 00:00:00 2001
-From: David Bauer <mail@david-bauer.net>
-Date: Thu, 15 Apr 2021 03:26:50 +0200
-Subject: [PATCH] net: phy: at803x: select correct page on config init
-
-The Atheros AR8031 and AR8033 expose different registers for SGMII/Fiber
-as well as the copper side of the PHY depending on the BT_BX_REG_SEL bit
-in the chip configure register.
-
-The driver assumes the copper side is selected on probe, but this might
-not be the case depending which page was last selected by the
-bootloader. Notably, Ubiquiti UniFi bootloaders show this behavior.
-
-Select the copper page when probing to circumvent this.
-
-Signed-off-by: David Bauer <mail@david-bauer.net>
-Signed-off-by: David S. Miller <davem@davemloft.net>
----
- drivers/net/phy/at803x.c | 50 +++++++++++++++++++++++++++++++++++++++-
- 1 file changed, 49 insertions(+), 1 deletion(-)
-
---- a/drivers/net/phy/at803x.c
-+++ b/drivers/net/phy/at803x.c
-@@ -139,6 +139,9 @@
- #define ATH8035_PHY_ID 0x004dd072
- #define AT8030_PHY_ID_MASK                    0xffffffef
- 
-+#define AT803X_PAGE_FIBER             0
-+#define AT803X_PAGE_COPPER            1
-+
- MODULE_DESCRIPTION("Qualcomm Atheros AR803x PHY driver");
- MODULE_AUTHOR("Matus Ujhelyi");
- MODULE_LICENSE("GPL");
-@@ -190,6 +193,35 @@ static int at803x_debug_reg_mask(struct
-       return phy_write(phydev, AT803X_DEBUG_DATA, val);
- }
- 
-+static int at803x_write_page(struct phy_device *phydev, int page)
-+{
-+      int mask;
-+      int set;
-+
-+      if (page == AT803X_PAGE_COPPER) {
-+              set = AT803X_BT_BX_REG_SEL;
-+              mask = 0;
-+      } else {
-+              set = 0;
-+              mask = AT803X_BT_BX_REG_SEL;
-+      }
-+
-+      return __phy_modify(phydev, AT803X_REG_CHIP_CONFIG, mask, set);
-+}
-+
-+static int at803x_read_page(struct phy_device *phydev)
-+{
-+      int ccr = __phy_read(phydev, AT803X_REG_CHIP_CONFIG);
-+
-+      if (ccr < 0)
-+              return ccr;
-+
-+      if (ccr & AT803X_BT_BX_REG_SEL)
-+              return AT803X_PAGE_COPPER;
-+
-+      return AT803X_PAGE_FIBER;
-+}
-+
- static int at803x_enable_rx_delay(struct phy_device *phydev)
- {
-       return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0, 0,
-@@ -508,6 +540,7 @@ static int at803x_probe(struct phy_devic
- {
-       struct device *dev = &phydev->mdio.dev;
-       struct at803x_priv *priv;
-+      int ret;
- 
-       priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
-       if (!priv)
-@@ -515,7 +548,20 @@ static int at803x_probe(struct phy_devic
- 
-       phydev->priv = priv;
- 
--      return at803x_parse_dt(phydev);
-+      ret = at803x_parse_dt(phydev);
-+      if (ret)
-+              return ret;
-+
-+      /* Some bootloaders leave the fiber page selected.
-+       * Switch to the copper page, as otherwise we read
-+       * the PHY capabilities from the fiber side.
-+       */
-+      if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
-+              ret = phy_select_page(phydev, AT803X_PAGE_COPPER);
-+              ret = phy_restore_page(phydev, AT803X_PAGE_COPPER, ret);
-+      }
-+
-+      return ret;
- }
- 
- static void at803x_remove(struct phy_device *phydev)
-@@ -1097,6 +1143,8 @@ static struct phy_driver at803x_driver[]
-       .get_wol                = at803x_get_wol,
-       .suspend                = at803x_suspend,
-       .resume                 = at803x_resume,
-+      .read_page              = at803x_read_page,
-+      .write_page             = at803x_write_page,
-       /* PHY_GBIT_FEATURES */
-       .read_status            = at803x_read_status,
-       .aneg_done              = at803x_aneg_done,