--- /dev/null
+From 0f03d9bfa1da1d26cb950e4b35b1ff7b9be1828f Mon Sep 17 00:00:00 2001
+From: =?UTF-8?q?Ar=C4=B1n=C3=A7=20=C3=9CNAL?= <arinc.unal@arinc9.com>
+Date: Mon, 22 Jan 2024 08:35:56 +0300
+Subject: [PATCH 27/48] net: dsa: mt7530: improve code path for setting up port
+ 5
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+There're two code paths for setting up port 5:
+
+mt7530_setup()
+-> mt7530_setup_port5()
+
+mt753x_phylink_mac_config()
+-> mt753x_mac_config()
+ -> mt7530_mac_config()
+ -> mt7530_setup_port5()
+
+Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5
+is used as a CPU, DSA, or user port, mt7530_setup_port5() from
+mt753x_phylink_mac_config() won't run. That is because priv->p5_interface
+set on mt7530_setup_port5() will match state->interface on
+mt753x_phylink_mac_config() which will stop running mt7530_setup_port5()
+again.
+
+Therefore, mt7530_setup_port5() will never run from
+mt753x_phylink_mac_config().
+
+Address this by not running mt7530_setup_port5() from mt7530_setup() if
+port 5 is used as a CPU, DSA, or user port. This driver isn't in the
+dsa_switches_apply_workarounds[] array so phylink will always be present.
+
+To keep the cases where port 5 isn't controlled by phylink working as
+before, preserve the mt7530_setup_port5() call from mt7530_setup().
+
+Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when
+"priv" is allocated.
+
+Move setting the interface to a more specific location. It's supposed to be
+overwritten if PHY muxing is detected.
+
+Improve the comment which explains the process.
+
+Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
+Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
+Link: https://lore.kernel.org/r/20240122-for-netnext-mt7530-improvements-1-v3-5-042401f2b279@arinc9.com
+Signed-off-by: Jakub Kicinski <kuba@kernel.org>
+---
+ drivers/net/dsa/mt7530.c | 17 ++++++++---------
+ 1 file changed, 8 insertions(+), 9 deletions(-)
+
+--- a/drivers/net/dsa/mt7530.c
++++ b/drivers/net/dsa/mt7530.c
+@@ -2353,16 +2353,15 @@ mt7530_setup(struct dsa_switch *ds)
+ return ret;
+
+ /* Setup port 5 */
+- priv->p5_intf_sel = P5_DISABLED;
+- interface = PHY_INTERFACE_MODE_NA;
+-
+ if (!dsa_is_unused_port(ds, 5)) {
+ priv->p5_intf_sel = P5_INTF_SEL_GMAC5;
+- ret = of_get_phy_mode(dsa_to_port(ds, 5)->dn, &interface);
+- if (ret && ret != -ENODEV)
+- return ret;
+ } else {
+- /* Scan the ethernet nodes. look for GMAC1, lookup used phy */
++ /* Scan the ethernet nodes. Look for GMAC1, lookup the used PHY.
++ * Set priv->p5_intf_sel to the appropriate value if PHY muxing
++ * is detected.
++ */
++ interface = PHY_INTERFACE_MODE_NA;
++
+ for_each_child_of_node(dn, mac_np) {
+ if (!of_device_is_compatible(mac_np,
+ "mediatek,eth-mac"))
+@@ -2393,6 +2392,8 @@ mt7530_setup(struct dsa_switch *ds)
+ of_node_put(phy_node);
+ break;
+ }
++
++ mt7530_setup_port5(ds, interface);
+ }
+
+ #ifdef CONFIG_GPIOLIB
+@@ -2403,8 +2404,6 @@ mt7530_setup(struct dsa_switch *ds)
+ }
+ #endif /* CONFIG_GPIOLIB */
+
+- mt7530_setup_port5(ds, interface);
+-
+ /* Flush the FDB table */
+ ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL);
+ if (ret < 0)