-#include "qcom-ipq8064-v1.0.dtsi"
+#include "qcom-ipq8064-v2.0-smb208.dtsi"
#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
/ {
model = "Netgear Nighthawk X4 R7500v2";
compatible = "netgear,r7500v2", "qcom,ipq8064";
memory@0 {
- reg = <0x42000000 0xe000000>;
+ reg = <0x42000000 0x1e000000>;
device_type = "memory";
};
reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
+ rsvd@5fe00000 {
+ reg = <0x5fe00000 0x200000>;
+ reusable;
};
};
aliases {
- serial0 = &uart4;
mdio-gpio0 = &mdio0;
+
+ led-boot = &power;
+ led-failsafe = &power;
+ led-running = &power;
+ led-upgrade = &power;
};
chosen {
bootargs = "rootfstype=squashfs noinitrd";
- linux,stdout-path = "serial0:115200n8";
};
- soc {
- pinmux@800000 {
- i2c4_pins: i2c4_pinmux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- bias-disable;
- };
+ keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&button_pins>;
+ pinctrl-names = "default";
- nand_pins: nand_pins {
- mux {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38", "gpio39",
- "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
- pullups {
- pins = "gpio39";
- bias-pull-up;
- };
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- bias-bus-hold;
- };
- };
+ wifi {
+ label = "wifi";
+ gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ debounce-interval = <60>;
+ wakeup-source;
+ };
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- };
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ debounce-interval = <60>;
+ wakeup-source;
+ };
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ debounce-interval = <60>;
+ wakeup-source;
};
+ };
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "ok";
- serial@16340000 {
- status = "ok";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ usb1 {
+ label = "amber:usb1";
+ gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
};
- sata-phy@1b400000 {
- status = "ok";
+ usb3 {
+ label = "amber:usb3";
+ gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
};
- sata@29000000 {
- status = "ok";
+ status {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_AMBER>;
+ gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
};
- phy@100f8800 { /* USB3 port 1 HS phy */
- status = "ok";
+ internet {
+ label = "white:internet";
+ gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
};
- phy@100f8830 { /* USB3 port 1 SS phy */
- status = "ok";
+ wan {
+ function = LED_FUNCTION_WAN;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
};
- phy@110f8800 { /* USB3 port 0 HS phy */
- status = "ok";
+ wps {
+ function = LED_FUNCTION_WPS;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
};
- phy@110f8830 { /* USB3 port 0 SS phy */
- status = "ok";
+ esata {
+ label = "white:esata";
+ gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
};
- usb30@0 {
- status = "ok";
+ power: power {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_WHITE>;
+ gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
};
- usb30@1 {
- status = "ok";
+ wifi {
+ label = "white:wifi";
+ gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
};
+ };
+};
+
+&adm_dma {
+ status = "okay";
+};
- pcie0: pci@1b500000 {
- status = "ok";
- reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio6", "gpio54", "gpio65";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
};
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+ "gpio24","gpio26", "gpio53", "gpio64";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ usb0_pwr_en_pins: usb0_pwr_en_pins {
+ mux {
+ pins = "gpio15";
+ function = "gpio";
+ drive-strength = <12>;
+ bias-pull-down;
+ output-high;
+ };
+ };
- pcie1: pci@1b700000 {
- status = "ok";
- reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
+ usb1_pwr_en_pins: usb1_pwr_en_pins {
+ mux {
+ pins = "gpio16", "gpio68";
+ function = "gpio";
+ drive-strength = <12>;
+ bias-pull-down;
+ output-high;
};
+ };
+};
+
+&sata_phy {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&hs_phy_0 {
+ status = "okay";
+};
- nand@1ac00000 {
- status = "ok";
+&ss_phy_0 {
+ status = "okay";
+};
+
+&usb3_0 {
+ status = "okay";
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
+ pinctrl-0 = <&usb0_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&hs_phy_1 {
+ status = "okay";
+};
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
+&ss_phy_1 {
+ status = "okay";
+};
+
+&usb3_1 {
+ status = "okay";
+
+ pinctrl-0 = <&usb1_pwr_en_pins>;
+ pinctrl-names = "default";
+};
+
+&pcie0 {
+ status = "okay";
+ reset-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pcie0_pins>;
+ pinctrl-names = "default";
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi@1,0 {
+ compatible = "pci168c,0040";
+ reg = <0x00010000 0 0 0 0>;
+
+ nvmem-cells = <&macaddr_art_6 1>, <&precal_art_1000>;
+ nvmem-cell-names = "mac-address", "pre-calibration";
+ };
+ };
+};
+
+&pcie1 {
+ status = "okay";
+ reset-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&pcie1_pins>;
+ pinctrl-names = "default";
+ max-link-speed = <1>;
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi@1,0 {
+ compatible = "pci168c,0040";
+ reg = <0x00010000 0 0 0 0>;
+
+ nvmem-cells = <&macaddr_art_6 2>, <&precal_art_5000>;
+ nvmem-cell-names = "mac-address", "pre-calibration";
+ };
+ };
+};
+&nand {
+ status = "okay";
+
+ nand@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ nand-is-boot-medium;
+ qcom,boot-partitions = <0x0 0x1180000>;
+
+ partitions {
+ compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
read-only;
};
- art: art@1200000 {
+ art@1200000 {
label = "art";
reg = <0x1200000 0x0140000>;
read-only;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ macaddr_art_0: macaddr@0 {
+ reg = <0x0 0x6>;
+ };
+
+ macaddr_art_6: macaddr@6 {
+ compatible = "mac-base";
+ reg = <0x6 0x6>;
+ #nvmem-cell-cells = <1>;
+ };
+
+ precal_art_1000: precal@1000 {
+ reg = <0x1000 0x2f20>;
+ };
+
+ precal_art_5000: precal@5000 {
+ reg = <0x5000 0x2f20>;
+ };
+ };
};
artbak: art@1340000 {
kernel@1480000 {
label = "kernel";
- reg = <0x1480000 0x0200000>;
+ reg = <0x1480000 0x0400000>;
};
- ubi@1680000 {
+ ubi@1880000 {
label = "ubi";
- reg = <0x1680000 0x1E00000>;
- };
-
- netgear@3480000 {
- label = "netgear";
- reg = <0x3480000 0x4480000>;
- read-only;
+ reg = <0x1880000 0x6080000>;
};
reserve@7900000 {
reg = <0x7900000 0x0700000>;
read-only;
};
+ };
+ };
+};
- firmware@1480000 {
- label = "firmware";
- reg = <0x1480000 0x2000000>;
- };
+&mdio0 {
+ status = "okay";
- };
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ switch@10 {
+ compatible = "qca,qca8337";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x10>;
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
+ ports {
#address-cells = <1>;
#size-cells = <0>;
- gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
- phy0: ethernet-phy@0 {
- device_type = "ethernet-phy";
+ port@0 {
reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0xaa545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- >;
+ label = "cpu";
+ ethernet = <&gmac1>;
+ phy-mode = "rgmii";
+ tx-internal-delay-ps = <1000>;
+ rx-internal-delay-ps = <1000>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
};
- phy4: ethernet-phy@4 {
- device_type = "ethernet-phy";
- reg = <4>;
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-mode = "internal";
+ phy-handle = <&phy_port1>;
};
- };
-
- gmac1: ethernet@37200000 {
- status = "ok";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
- mtd-mac-address = <&art 6>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-mode = "internal";
+ phy-handle = <&phy_port2>;
};
- };
- gmac2: ethernet@37400000 {
- status = "ok";
- phy-mode = "sgmii";
- qcom,id = <2>;
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ phy-mode = "internal";
+ phy-handle = <&phy_port3>;
+ };
- mtd-mac-address = <&art 0>;
+ port@4 {
+ reg = <4>;
+ label = "lan4";
+ phy-mode = "internal";
+ phy-handle = <&phy_port4>;
+ };
- fixed-link {
- speed = <1000>;
- full-duplex;
+ port@5 {
+ reg = <5>;
+ label = "wan";
+ phy-mode = "internal";
+ phy-handle = <&phy_port5>;
};
- };
- };
- gpio-keys {
- compatible = "gpio-keys";
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&gmac2>;
+ phy-mode = "sgmii";
+ qca,sgmii-enable-pll;
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 6 1>;
- linux,code = <KEY_WLAN>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
};
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 1>;
- linux,code = <KEY_RESTART>;
- };
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 1>;
- linux,code = <KEY_WPS_BUTTON>;
- };
- };
+ phy_port1: phy@0 {
+ reg = <0>;
+ };
- gpio-leds {
- compatible = "gpio-leds";
+ phy_port2: phy@1 {
+ reg = <1>;
+ };
- usb1 {
- label = "r7500v2:amber:usb1";
- gpios = <&qcom_pinmux 7 0>;
- };
+ phy_port3: phy@2 {
+ reg = <2>;
+ };
- usb3 {
- label = "r7500v2:amber:usb3";
- gpios = <&qcom_pinmux 8 0>;
- };
+ phy_port4: phy@3 {
+ reg = <3>;
+ };
- status {
- label = "r7500v2:amber:status";
- gpios = <&qcom_pinmux 9 0>;
+ phy_port5: phy@4 {
+ reg = <4>;
+ };
};
+ };
+};
- internet {
- label = "r7500v2:white:internet";
- gpios = <&qcom_pinmux 22 0>;
- };
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
- wan {
- label = "r7500v2:white:wan";
- gpios = <&qcom_pinmux 23 0>;
- };
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
- wps {
- label = "r7500v2:white:wps";
- gpios = <&qcom_pinmux 24 0>;
- };
+ nvmem-cells = <&macaddr_art_6 0>;
+ nvmem-cell-names = "mac-address";
- esata {
- label = "r7500v2:white:esata";
- gpios = <&qcom_pinmux 26 0>;
- };
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
- power {
- label = "r7500v2:white:power";
- gpios = <&qcom_pinmux 53 0>;
- default-state = "on";
- };
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
- rfkill {
- label = "r7500v2:white:rfkill";
- gpios = <&qcom_pinmux 64 0>;
- };
+ nvmem-cells = <&macaddr_art_0>;
+ nvmem-cell-names = "mac-address";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
};
};
-
-&adm_dma {
- status = "ok";
-};