+++ /dev/null
-#include "qcom-ipq8064-v2.0.dtsi"
-
-#include <dt-bindings/input/input.h>
-
-/ {
- model = "Netgear Nighthawk X4 D7800";
- compatible = "netgear,d7800", "qcom,ipq8064";
-
- memory@0 {
- reg = <0x42000000 0xe000000>;
- device_type = "memory";
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
- rsvd@41200000 {
- reg = <0x41200000 0x300000>;
- no-map;
- };
- };
-
- aliases {
- serial0 = &gsbi4_serial;
- mdio-gpio0 = &mdio0;
-
- led-boot = &power_white;
- led-failsafe = &power_amber;
- led-running = &power_white;
- led-upgrade = &power_amber;
- };
-
- chosen {
- bootargs = "rootfstype=squashfs noinitrd";
- stdout-path = "serial0:115200n8";
- };
-
- soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- nand_pins: nand_pins {
- disable {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
-
- pullups {
- pins = "gpio39";
- function = "nand";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-bus-hold;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- usb0_pwr_en_pins: usb0_pwr_en_pins {
- mux {
- pins = "gpio15";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
-
- usb1_pwr_en_pins: usb1_pwr_en_pins {
- mux {
- pins = "gpio16", "gpio68";
- function = "gpio";
- drive-strength = <12>;
- bias-pull-down;
- output-high;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- serial@16340000 {
- status = "okay";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- sata-phy@1b400000 {
- status = "okay";
- };
-
- sata@29000000 {
- ports-implemented = <0x1>;
- status = "okay";
- };
-
- usb3_0: usb3@110f8800 {
- status = "okay";
-
- pinctrl-0 = <&usb0_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- usb3_1: usb3@100f8800 {
- status = "okay";
-
- pinctrl-0 = <&usb1_pwr_en_pins>;
- pinctrl-names = "default";
- };
-
- pcie0: pci@1b500000 {
- status = "okay";
- reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie0_pins>;
- pinctrl-names = "default";
- };
-
- pcie1: pci@1b700000 {
- status = "okay";
- reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&pcie1_pins>;
- pinctrl-names = "default";
- force_gen1 = <1>;
- };
-
- nand@1ac00000 {
- status = "okay";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- cs0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- qcadata@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art: art@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
- };
-
- artbak: art@1340000 {
- label = "artbak";
- reg = <0x1340000 0x0140000>;
- read-only;
- };
-
- kernel@1480000 {
- label = "kernel";
- reg = <0x1480000 0x0400000>;
- };
-
- ubi@1880000 {
- label = "ubi";
- reg = <0x1880000 0x1C00000>;
- };
-
- netgear@3480000 {
- label = "netgear";
- reg = <0x3480000 0x4480000>;
- read-only;
- };
-
- reserve@7900000 {
- label = "reserve";
- reg = <0x7900000 0x0700000>;
- read-only;
- };
- };
- };
- };
-
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
- <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy0: ethernet-phy@0 {
- reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0x6a545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- >;
- };
-
- phy4: ethernet-phy@4 {
- reg = <4>;
- };
- };
-
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "rgmii";
- phy-handle = <&phy4>;
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&art 6>;
- };
-
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&art 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- keys {
- compatible = "gpio-keys";
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- wifi {
- label = "wifi";
- gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RFKILL>;
- };
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
-
- wps {
- label = "wps";
- gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_WPS_BUTTON>;
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- usb1 {
- label = "white:usb1";
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb2 {
- label = "white:usb2";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
-
- power_amber: power_amber {
- label = "amber:power";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- wan_white {
- label = "white:wan";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
-
- wan_amber {
- label = "amber:wan";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- wps {
- label = "white:wps";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- };
-
- esata {
- label = "white:esata";
- gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
-
- power_white: power_white {
- label = "white:power";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- wifi {
- label = "white:wifi";
- gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&adm_dma {
- status = "okay";
-};
projects / openwrt / openwrt.git / blobdiff