+// SPDX-License-Identifier: GPL-2.0
/dts-v1/;
#include "skeleton.dtsi"
CPU_SPC: spc {
compatible = "qcom,idle-state-spc",
"arm,idle-state";
+ status = "okay";
entry-latency-us = <400>;
exit-latency-us = <900>;
min-residency-us = <3000>;
cpu-pmu {
compatible = "qcom,krait-pmu";
- interrupts = <1 10 0x304>;
+ interrupts = <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_LEVEL_HIGH)>;
};
reserved-memory {
clock-names = "ahbix-clk",
"mi2s-osr-clk",
"mi2s-bit-clk";
- interrupts = <0 85 1>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "lpass-irq-lpaif";
reg = <0x28100000 0x10000>;
reg-names = "lpass-lpaif";
reg = <0x108000 0x1000>;
qcom,ipc = <&l2cc 0x8 2>;
- interrupts = <0 19 0>,
- <0 21 0>,
- <0 22 0>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "ack",
"err",
"wakeup";
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
- interrupts = <0 16 0x4>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
pcie0_pins: pcie0_pinmux {
mux {
pins = "gpio3";
function = "pcie1_rst";
- drive-strength = <2>;
+ drive-strength = <12>;
bias-disable;
};
};
mux {
pins = "gpio48";
function = "pcie2_rst";
- drive-strength = <2>;
+ drive-strength = <12>;
bias-disable;
};
};
mux {
pins = "gpio63";
function = "pcie3_rst";
- drive-strength = <2>;
+ drive-strength = <12>;
bias-disable;
output-low;
};
};
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ drive-strength = <10>;
+ bias-none;
+ };
+ };
+
+ leds_pins: leds_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9",
+ "gpio26", "gpio53";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ output-low;
+ };
+ };
+
+ buttons_pins: buttons_pins {
+ mux {
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
};
intc: interrupt-controller@2000000 {
};
timer@200a000 {
- compatible = "qcom,kpss-timer", "qcom,msm-timer";
- interrupts = <1 1 0x301>,
- <1 2 0x301>,
- <1 3 0x301>,
- <1 4 0x301>,
- <1 5 0x301>;
+ compatible = "qcom,kpss-timer",
+ "qcom,kpss-wdt-ipq8064", "qcom,msm-timer";
+ interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_EDGE_RISING)>,
+ <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_EDGE_RISING)>,
+ <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_EDGE_RISING)>,
+ <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_EDGE_RISING)>,
+ <GIC_PPI 5 (GIC_CPU_MASK_SIMPLE(2) |
+ IRQ_TYPE_EDGE_RISING)>;
reg = <0x0200a000 0x100>;
clock-frequency = <25000000>,
<32768>;
};
saw0: regulator@2089000 {
- compatible = "qcom,saw2", "syscon";
+ compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon";
reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
regulator;
};
saw1: regulator@2099000 {
- compatible = "qcom,saw2", "syscon";
+ compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon";
reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
regulator;
};
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x12490000 0x1000>,
<0x12480000 0x1000>;
- interrupts = <0 195 0x0>;
+ interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI2_UART_CLK>, <&gcc GSBI2_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
i2c@124a0000 {
compatible = "qcom,i2c-qup-v1.1.1";
reg = <0x124a0000 0x1000>;
- interrupts = <0 196 0>;
+ interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
clock-names = "core", "iface";
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x16340000 0x1000>,
<0x16300000 0x1000>;
- interrupts = <0 152 0x0>;
+ interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
i2c@16380000 {
compatible = "qcom,i2c-qup-v1.1.1";
reg = <0x16380000 0x1000>;
- interrupts = <0 153 0>;
+ interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
clock-names = "core", "iface";
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x1a240000 0x1000>,
<0x1a200000 0x1000>;
- interrupts = <0 154 0x0>;
+ interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
clock-names = "core", "iface";
status = "disabled";
i2c@1a280000 {
compatible = "qcom,i2c-qup-v1.1.1";
reg = <0x1a280000 0x1000>;
- interrupts = <0 155 0>;
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
clock-names = "core", "iface";
spi@1a280000 {
compatible = "qcom,spi-qup-v1.1.1";
reg = <0x1a280000 0x1000>;
- interrupts = <0 155 0>;
+ interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
clock-names = "core", "iface";
};
};
+ gsbi7: gsbi@16600000 {
+ status = "disabled";
+ compatible = "qcom,gsbi-v1.0.0";
+ cell-index = <7>;
+ reg = <0x16600000 0x100>;
+ clocks = <&gcc GSBI7_H_CLK>;
+ clock-names = "iface";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ syscon-tcsr = <&tcsr>;
+
+ gsbi7_serial: serial@16640000 {
+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+ reg = <0x16640000 0x1000>,
+ <0x16600000 0x1000>;
+ interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
+ clock-names = "core", "iface";
+ status = "disabled";
+ };
+ };
+
sata_phy: sata-phy@1b400000 {
compatible = "qcom,ipq806x-sata-phy";
reg = <0x1b400000 0x200>;
status = "disabled";
};
- sata@29000000 {
+ sata: sata@29000000 {
compatible = "qcom,ipq806x-ahci", "generic-ahci";
reg = <0x29000000 0x180>;
- ports-implemented = <0x1>;
-
- interrupts = <0 209 0x0>;
+ interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc SFAB_SATA_S_H_CLK>,
<&gcc SATA_H_CLK>,
reg = <0x900000 0x3680>;
nvmem-cells = <&tsens_calib>, <&tsens_backup>;
nvmem-cell-names = "calib", "calib_backup";
- interrupts = <0 178 0>;
+ interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
#thermal-sensor-cells = <1>;
};
compatible = "syscon";
reg = <0x01200600 0x100>;
};
+
+ hs_phy_0: hs_phy_0 {
+ compatible = "qcom,dwc3-hs-usb-phy";
+ regmap = <&usb3_0>;
+ clocks = <&gcc USB30_0_UTMI_CLK>;
+ clock-names = "ref";
+ #phy-cells = <0>;
+ };
- hs_phy_1: phy@100f8800 {
- compatible = "qcom,dwc3-hs-usb-phy";
- reg = <0x100f8800 0x30>;
- clocks = <&gcc USB30_1_UTMI_CLK>;
- clock-names = "ref";
- #phy-cells = <0>;
-
- status = "disabled";
- };
-
- ss_phy_1: phy@100f8830 {
- compatible = "qcom,dwc3-ss-usb-phy";
- reg = <0x100f8830 0x30>;
- clocks = <&gcc USB30_1_MASTER_CLK>;
- clock-names = "ref";
- #phy-cells = <0>;
-
- status = "disabled";
- };
-
- hs_phy_0: phy@110f8800 {
- compatible = "qcom,dwc3-hs-usb-phy";
- reg = <0x110f8800 0x30>;
- clocks = <&gcc USB30_0_UTMI_CLK>;
- clock-names = "ref";
- #phy-cells = <0>;
-
- status = "disabled";
- };
-
- ss_phy_0: phy@110f8830 {
- compatible = "qcom,dwc3-ss-usb-phy";
- reg = <0x110f8830 0x30>;
- clocks = <&gcc USB30_0_MASTER_CLK>;
- clock-names = "ref";
- #phy-cells = <0>;
-
- status = "disabled";
- };
+ ss_phy_0: ss_phy_0 {
+ compatible = "qcom,dwc3-ss-usb-phy";
+ regmap = <&usb3_0>;
+ clocks = <&gcc USB30_0_MASTER_CLK>;
+ clock-names = "ref";
+ #phy-cells = <0>;
+ };
- usb3_0: usb30@0 {
- compatible = "qcom,dwc3";
+ usb3_0: usb3@110f8800 {
+ compatible = "qcom,dwc3", "syscon";
#address-cells = <1>;
#size-cells = <1>;
+ reg = <0x110f8800 0x8000>;
clocks = <&gcc USB30_0_MASTER_CLK>;
clock-names = "core";
ranges;
resets = <&gcc USB30_0_MASTER_RESET>;
- reset-names = "usb30_0_mstr_rst";
+ reset-names = "master";
status = "disabled";
dwc3_0: dwc3@11000000 {
compatible = "snps,dwc3";
reg = <0x11000000 0xcd00>;
- interrupts = <0 110 0x4>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
phys = <&hs_phy_0>, <&ss_phy_0>;
phy-names = "usb2-phy", "usb3-phy";
dr_mode = "host";
snps,dis_u3_susphy_quirk;
};
};
+
+ hs_phy_1: hs_phy_1 {
+ compatible = "qcom,dwc3-hs-usb-phy";
+ regmap = <&usb3_1>;
+ clocks = <&gcc USB30_1_UTMI_CLK>;
+ clock-names = "ref";
+ #phy-cells = <0>;
+ };
- usb3_1: usb30@1 {
- compatible = "qcom,dwc3";
+ ss_phy_1: ss_phy_1 {
+ compatible = "qcom,dwc3-ss-usb-phy";
+ regmap = <&usb3_1>;
+ clocks = <&gcc USB30_1_MASTER_CLK>;
+ clock-names = "ref";
+ #phy-cells = <0>;
+ };
+
+ usb3_1: usb3@100f8800 {
+ compatible = "qcom,dwc3", "syscon";
#address-cells = <1>;
#size-cells = <1>;
+ reg = <0x100f8800 0x8000>;
clocks = <&gcc USB30_1_MASTER_CLK>;
clock-names = "core";
ranges;
resets = <&gcc USB30_1_MASTER_RESET>;
- reset-names = "usb30_1_mstr_rst";
+ reset-names = "master";
status = "disabled";
dwc3_1: dwc3@10000000 {
compatible = "snps,dwc3";
reg = <0x10000000 0xcd00>;
- interrupts = <0 205 0x4>;
+ interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
phys = <&hs_phy_1>, <&ss_phy_1>;
phy-names = "usb2-phy", "usb3-phy";
dr_mode = "host";
ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000 /* downstream I/O */
0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */
- interrupts = <GIC_SPI 35 IRQ_TYPE_NONE>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000 /* downstream I/O */
0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
- interrupts = <GIC_SPI 57 IRQ_TYPE_NONE>;
+ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000 /* downstream I/O */
0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */
- interrupts = <GIC_SPI 71 IRQ_TYPE_NONE>;
+ interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
adm_dma: dma@18300000 {
compatible = "qcom,adm";
reg = <0x18300000 0x100000>;
- interrupts = <0 170 0>;
+ interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
#dma-cells = <1>;
clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
status = "disabled";
};
- nand@1ac00000 {
+ nand: nand@1ac00000 {
compatible = "qcom,ipq806x-nand";
reg = <0x1ac00000 0x800>;
};
gmac0: ethernet@37000000 {
- device_type = "network";
compatible = "qcom,ipq806x-gmac";
reg = <0x37000000 0x200000>;
interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
};
gmac1: ethernet@37200000 {
- device_type = "network";
compatible = "qcom,ipq806x-gmac";
reg = <0x37200000 0x200000>;
interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
};
gmac2: ethernet@37400000 {
- device_type = "network";
compatible = "qcom,ipq806x-gmac";
reg = <0x37400000 0x200000>;
interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
};
gmac3: ethernet@37600000 {
- device_type = "network";
compatible = "qcom,ipq806x-gmac";
reg = <0x37600000 0x200000>;
interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
sdcc1bam:dma@12402000 {
compatible = "qcom,bam-v1.3.0";
reg = <0x12402000 0x8000>;
- interrupts = <0 98 0>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc SDC1_H_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
sdcc3bam:dma@12182000 {
compatible = "qcom,bam-v1.3.0";
reg = <0x12182000 0x8000>;
- interrupts = <0 96 0>;
+ interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc SDC3_H_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
};
amba {
- compatible = "arm,amba-bus";
+ compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
+
sdcc1: sdcc@12400000 {
status = "disabled";
compatible = "arm,pl18x", "arm,primecell";
projects / openwrt / staging / ynezz.git / blobdiff