--- /dev/null
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Netgear Nighthawk X4 R7500";
+ compatible = "netgear,r7500", "qcom,ipq8064";
+
+ memory@0 {
+ reg = <0x42000000 0xe000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &gsbi4_serial;
+ mdio-gpio0 = &mdio0;
+
+ led-boot = &power_white;
+ led-failsafe = &power_amber;
+ led-running = &power_white;
+ led-upgrade = &power_amber;
+ };
+
+ chosen {
+ bootargs = "rootfstype=squashfs noinitrd";
+ linux,stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ pinmux@800000 {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio6", "gpio54", "gpio65";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ i2c4_pins: i2c4_pinmux {
+ mux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+ "gpio24","gpio26", "gpio53", "gpio64";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ mux {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38", "gpio39",
+ "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+ pullups {
+ pins = "gpio39";
+ bias-pull-up;
+ };
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ bias-bus-hold;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+ };
+
+ gsbi@16300000 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "ok";
+ serial@16340000 {
+ status = "ok";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+ };
+
+ sata-phy@1b400000 {
+ status = "ok";
+ };
+
+ sata@29000000 {
+ status = "ok";
+ };
+
+ phy@100f8800 { /* USB3 port 1 HS phy */
+ status = "ok";
+ };
+
+ phy@100f8830 { /* USB3 port 1 SS phy */
+ status = "ok";
+ };
+
+ phy@110f8800 { /* USB3 port 0 HS phy */
+ status = "ok";
+ };
+
+ phy@110f8830 { /* USB3 port 0 SS phy */
+ status = "ok";
+ };
+
+ usb30@0 {
+ status = "ok";
+ };
+
+ usb30@1 {
+ status = "ok";
+ };
+
+ pcie0: pci@1b500000 {
+ status = "ok";
+ };
+
+ pcie1: pci@1b700000 {
+ status = "ok";
+ };
+
+ nand@1ac00000 {
+ status = "ok";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qcadata@0 {
+ label = "qcadata";
+ reg = <0x0000000 0x0c80000>;
+ read-only;
+ };
+
+ APPSBL@c80000 {
+ label = "APPSBL";
+ reg = <0x0c80000 0x0500000>;
+ read-only;
+ };
+
+ APPSBLENV@1180000 {
+ label = "APPSBLENV";
+ reg = <0x1180000 0x0080000>;
+ read-only;
+ };
+
+ art: art@1200000 {
+ label = "art";
+ reg = <0x1200000 0x0140000>;
+ read-only;
+ };
+
+ kernel@1340000 {
+ label = "kernel";
+ reg = <0x1340000 0x0200000>;
+ };
+
+ ubi@1540000 {
+ label = "ubi";
+ reg = <0x1540000 0x1800000>;
+ };
+
+ netgear@2d40000 {
+ label = "netgear";
+ reg = <0x2d40000 0x0c00000>;
+ read-only;
+ };
+
+ reserve@3940000 {
+ label = "reserve";
+ reg = <0x3940000 0x46c0000>;
+ read-only;
+ };
+
+ firmware@1340000 {
+ label = "firmware";
+ reg = <0x1340000 0x1a00000>;
+ };
+
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH &qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
+ };
+
+ phy4: ethernet-phy@4 {
+ device_type = "ethernet-phy";
+ reg = <4>;
+ };
+ };
+
+ gmac1: ethernet@37200000 {
+ status = "ok";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&art 6>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ gmac2: ethernet@37400000 {
+ status = "ok";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&art 0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ rpm@108000 {
+ pinctrl-0 = <&i2c4_pins>;
+ pinctrl-names = "default";
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&button_pins>;
+ pinctrl-names = "default";
+
+ wifi {
+ label = "wifi";
+ gpios = <&qcom_pinmux 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ usb1 {
+ label = "r7500:white:usb1";
+ gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb2 {
+ label = "r7500:white:usb2";
+ gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ power_amber: power_amber {
+ label = "r7500:amber:power";
+ gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ wan_white {
+ label = "r7500:white:wan";
+ gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
+ };
+
+ wan_amber {
+ label = "r7500:amber:wan";
+ gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
+ };
+
+ wps {
+ label = "r7500:white:wps";
+ gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ esata {
+ label = "r7500:white:esata";
+ gpios = <&qcom_pinmux 26 GPIO_ACTIVE_HIGH>;
+ };
+
+ power_white: power_white {
+ label = "r7500:white:power";
+ gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ };
+
+ wifi {
+ label = "r7500:white:wifi";
+ gpios = <&qcom_pinmux 64 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&adm_dma {
+ status = "ok";
+};
projects / openwrt / staging / blogic.git / blobdiff