};
aliases {
- serial0 = &gsbi4_serial;
mdio-gpio0 = &mdio0;
led-boot = &power_white;
chosen {
bootargs = "rootfstype=squashfs noinitrd";
- stdout-path = "serial0:115200n8";
- };
-
- soc {
- pinmux@800000 {
- button_pins: button_pins {
- mux {
- pins = "gpio6", "gpio54", "gpio65";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- i2c4_pins: i2c4_pinmux {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
- "gpio24","gpio26", "gpio53", "gpio64";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- mdio0_pins: mdio0_pins {
- mux {
- pins = "gpio0", "gpio1";
- function = "gpio";
- drive-strength = <8>;
- bias-disable;
- };
- };
-
- nand_pins: nand_pins {
- disable {
- pins = "gpio34", "gpio35", "gpio36",
- "gpio37", "gpio38";
- function = "nand";
- drive-strength = <10>;
- bias-disable;
- };
-
- pullups {
- pins = "gpio39";
- function = "nand";
- drive-strength = <10>;
- bias-pull-up;
- };
-
- hold {
- pins = "gpio40", "gpio41", "gpio42",
- "gpio43", "gpio44", "gpio45",
- "gpio46", "gpio47";
- function = "nand";
- drive-strength = <10>;
- bias-bus-hold;
- };
- };
-
- rgmii2_pins: rgmii2_pins {
- mux {
- pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
- "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
- function = "rgmii2";
- drive-strength = <8>;
- bias-disable;
- };
- };
- };
-
- gsbi@16300000 {
- qcom,mode = <GSBI_PROT_I2C_UART>;
- status = "okay";
- serial@16340000 {
- status = "okay";
- };
- /*
- * The i2c device on gsbi4 should not be enabled.
- * On ipq806x designs gsbi4 i2c is meant for exclusive
- * RPM usage. Turning this on in kernel manifests as
- * i2c failure for the RPM.
- */
- };
-
- sata-phy@1b400000 {
- status = "okay";
- };
-
- sata@29000000 {
- status = "okay";
- };
-
- usb3_0: usb3@110f8800 {
- clocks = <&gcc USB30_1_MASTER_CLK>;
- status = "okay";
- };
-
- usb3_1: usb3@100f8800 {
- clocks = <&gcc USB30_0_MASTER_CLK>;
- status = "okay";
- };
-
- pcie0: pci@1b500000 {
- status = "okay";
- };
-
- pcie1: pci@1b700000 {
- status = "okay";
- force_gen1 = <1>;
- };
-
- nand-controller@1ac00000 {
- status = "okay";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- nand@0 {
- reg = <0>;
- compatible = "qcom,nandcs";
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- qcadata@0 {
- label = "qcadata";
- reg = <0x0000000 0x0c80000>;
- read-only;
- };
-
- APPSBL@c80000 {
- label = "APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- APPSBLENV@1180000 {
- label = "APPSBLENV";
- reg = <0x1180000 0x0080000>;
- read-only;
- };
-
- art: art@1200000 {
- label = "art";
- reg = <0x1200000 0x0140000>;
- read-only;
- };
-
- kernel@1340000 {
- label = "kernel";
- reg = <0x1340000 0x0400000>;
- };
-
- ubi@1740000 {
- label = "ubi";
- reg = <0x1740000 0x1600000>;
- };
-
- netgear@2d40000 {
- label = "netgear";
- reg = <0x2d40000 0x0c00000>;
- read-only;
- };
-
- reserve@3940000 {
- label = "reserve";
- reg = <0x3940000 0x46c0000>;
- read-only;
- };
- };
- };
- };
-
- mdio0: mdio {
- compatible = "virtual,mdio-gpio";
- #address-cells = <1>;
- #size-cells = <0>;
- gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
- <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- phy0: ethernet-phy@0 {
- reg = <0>;
- qca,ar8327-initvals = <
- 0x00004 0x7600000 /* PAD0_MODE */
- 0x00008 0x1000000 /* PAD5_MODE */
- 0x0000c 0x80 /* PAD6_MODE */
- 0x000e4 0x6a545 /* MAC_POWER_SEL */
- 0x000e0 0xc74164de /* SGMII_CTRL */
- 0x0007c 0x4e /* PORT0_STATUS */
- 0x00094 0x4e /* PORT6_STATUS */
- >;
- };
-
- phy4: ethernet-phy@4 {
- reg = <4>;
- };
- };
-
- gmac1: ethernet@37200000 {
- status = "okay";
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- mtd-mac-address = <&art 6>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- gmac2: ethernet@37400000 {
- status = "okay";
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- mtd-mac-address = <&art 0>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
};
keys {
};
};
+&qcom_pinmux {
+ button_pins: button_pins {
+ mux {
+ pins = "gpio6", "gpio54", "gpio65";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ led_pins: led_pins {
+ mux {
+ pins = "gpio7", "gpio8", "gpio9", "gpio22", "gpio23",
+ "gpio24","gpio26", "gpio53", "gpio64";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+};
+
+&gsbi4 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "okay";
+ serial@16340000 {
+ status = "okay";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+};
+
+&sata_phy {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&usb3_0 {
+ clocks = <&gcc USB30_1_MASTER_CLK>;
+ status = "okay";
+};
+
+&usb3_1 {
+ clocks = <&gcc USB30_0_MASTER_CLK>;
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+ force_gen1 = <1>;
+};
+
+&nand_controller {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand@0 {
+ reg = <0>;
+ compatible = "qcom,nandcs";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+ nand-ecc-step-size = <512>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qcadata@0 {
+ label = "qcadata";
+ reg = <0x0000000 0x0c80000>;
+ read-only;
+ };
+
+ APPSBL@c80000 {
+ label = "APPSBL";
+ reg = <0x0c80000 0x0500000>;
+ read-only;
+ };
+
+ APPSBLENV@1180000 {
+ label = "APPSBLENV";
+ reg = <0x1180000 0x0080000>;
+ read-only;
+ };
+
+ art: art@1200000 {
+ label = "art";
+ reg = <0x1200000 0x0140000>;
+ read-only;
+ };
+
+ kernel@1340000 {
+ label = "kernel";
+ reg = <0x1340000 0x0400000>;
+ };
+
+ ubi@1740000 {
+ label = "ubi";
+ reg = <0x1740000 0x1600000>;
+ };
+
+ netgear@2d40000 {
+ label = "netgear";
+ reg = <0x2d40000 0x0c00000>;
+ read-only;
+ };
+
+ reserve@3940000 {
+ label = "reserve";
+ reg = <0x3940000 0x46c0000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&mdio0 {
+ status = "okay";
+
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0x6a545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
+ };
+
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ };
+};
+
+&gmac1 {
+ status = "okay";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&art 6>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
+&gmac2 {
+ status = "okay";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&art 0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+};
+
&tcsr {
qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>;
compatible = "qcom,tcsr";
projects / openwrt / openwrt.git / blobdiff