+++ /dev/null
-// SPDX-License-Identifier: BSD-3-Clause
-/*
- * Copyright (C) 2017 Christian Mehlis <christian@m3hlis.de>
- * Copyright (C) 2018 Mathias Kresin <dev@kresin.me>
- * All rights reserved.
- */
-
-#include "qcom-ipq8064-v1.0.dtsi"
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/soc/qcom,tcsr.h>
-
-/ {
- compatible = "compex,wpq864", "qcom,ipq8064";
- model = "Compex WPQ864";
-
- aliases {
- mdio-gpio0 = &mdio0;
- ethernet0 = &gmac1;
- ethernet1 = &gmac0;
-
- led-boot = &led_pass;
- led-failsafe = &led_fail;
- led-running = &led_pass;
- led-upgrade = &led_pass;
- };
-
- leds {
- compatible = "gpio-leds";
-
- pinctrl-0 = <&led_pins>;
- pinctrl-names = "default";
-
- rss4 {
- label = "green:rss4";
- gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>;
- };
-
- rss3 {
- label = "green:rss3";
- gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>;
- default-state = "keep";
- };
-
- rss2 {
- label = "orange:rss2";
- gpios = <&qcom_pinmux 25 GPIO_ACTIVE_HIGH>;
- };
-
- rss1 {
- label = "red:rss1";
- gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>;
- };
-
- led_pass: pass {
- label = "green:pass";
- gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
- };
-
- led_fail: fail {
- label = "green:fail";
- gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
- };
-
- usb {
- function = LED_FUNCTION_USB;
- color = <LED_COLOR_ID_GREEN>;
- gpios = <&qcom_pinmux 7 GPIO_ACTIVE_HIGH>;
- };
-
- usb-pcie {
- label = "green:usb-pcie";
- gpios = <&qcom_pinmux 8 GPIO_ACTIVE_HIGH>;
- };
- };
-
- keys {
- compatible = "gpio-keys";
-
- pinctrl-0 = <&button_pins>;
- pinctrl-names = "default";
-
- reset {
- label = "reset";
- gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- debounce-interval = <60>;
- wakeup-source;
- };
- };
-
- beeper {
- compatible = "gpio-beeper";
-
- pinctrl-0 = <&beeper_pins>;
- pinctrl-names = "default";
-
- gpios = <&qcom_pinmux 55 GPIO_ACTIVE_HIGH>;
- };
-};
-
-&rpm {
- pinctrl-0 = <&rpm_pins>;
- pinctrl-names = "default";
-};
-
-&nand {
- status = "okay";
-
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
-
- mt29f2g08abbeah4@0 {
- compatible = "qcom,nandcs";
-
- reg = <0>;
-
- nand-ecc-strength = <4>;
- nand-bus-width = <8>;
- nand-ecc-step-size = <512>;
-
- nand-is-boot-medium;
- qcom,boot-partitions = <0x0 0x1180000 0x5340000 0x10c0000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- label = "0:SBL1";
- reg = <0x0000000 0x0040000>;
- read-only;
- };
-
- partition@40000 {
- label = "0:MIBIB";
- reg = <0x0040000 0x0140000>;
- read-only;
- };
-
- partition@180000 {
- label = "0:SBL2";
- reg = <0x0180000 0x0140000>;
- read-only;
- };
-
- partition@2c0000 {
- label = "0:SBL3";
- reg = <0x02c0000 0x0280000>;
- read-only;
- };
-
- partition@540000 {
- label = "0:DDRCONFIG";
- reg = <0x0540000 0x0120000>;
- read-only;
- };
-
- partition@660000 {
- label = "0:SSD";
- reg = <0x0660000 0x0120000>;
- read-only;
- };
-
- partition@780000 {
- label = "0:TZ";
- reg = <0x0780000 0x0280000>;
- read-only;
- };
-
- partition@a00000 {
- label = "0:RPM";
- reg = <0x0a00000 0x0280000>;
- read-only;
- };
-
- partition@c80000 {
- label = "0:APPSBL";
- reg = <0x0c80000 0x0500000>;
- read-only;
- };
-
- partition@1180000 {
- label = "0:APPSBLENV";
- reg = <0x1180000 0x0080000>;
- };
-
- partition@1200000 {
- label = "0:ART";
- reg = <0x1200000 0x0140000>;
- };
-
- partition@1340000 {
- label = "ubi";
- reg = <0x1340000 0x4000000>;
- };
-
- partition@5340000 {
- label = "0:BOOTCONFIG";
- reg = <0x5340000 0x0060000>;
- };
-
- partition@53a0000 {
- label = "0:SBL2_1";
- reg = <0x53a0000 0x0140000>;
- read-only;
- };
-
- partition@54e0000 {
- label = "0:SBL3_1";
- reg = <0x54e0000 0x0280000>;
- read-only;
- };
-
- partition@5760000 {
- label = "0:DDRCONFIG_1";
- reg = <0x5760000 0x0120000>;
- read-only;
- };
-
- partition@5880000 {
- label = "0:SSD_1";
- reg = <0x5880000 0x0120000>;
- read-only;
- };
-
- partition@59a0000 {
- label = "0:TZ_1";
- reg = <0x59a0000 0x0280000>;
- read-only;
- };
-
- partition@5c20000 {
- label = "0:RPM_1";
- reg = <0x5c20000 0x0280000>;
- read-only;
- };
-
- partition@5ea0000 {
- label = "0:BOOTCONFIG1";
- reg = <0x5ea0000 0x0060000>;
- };
-
- partition@5f00000 {
- label = "0:APPSBL_1";
- reg = <0x5f00000 0x0500000>;
- read-only;
- };
-
- partition@6400000 {
- label = "ubi_1";
- reg = <0x6400000 0x4000000>;
- };
-
- partition@a400000 {
- label = "unused";
- reg = <0xa400000 0x5c00000>;
- };
- };
- };
-};
-
-&adm_dma {
- status = "okay";
-};
-
-&mdio0 {
- status = "okay";
-
- pinctrl-0 = <&mdio0_pins>;
- pinctrl-names = "default";
-
- switch@10 {
- compatible = "qca,qca8337";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0x10>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "cpu";
- ethernet = <&gmac1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <1000>;
- rx-internal-delay-ps = <1000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- port@1 {
- reg = <1>;
- label = "lan1";
- phy-mode = "internal";
- phy-handle = <&phy_port1>;
- };
-
- port@2 {
- reg = <2>;
- label = "lan2";
- phy-mode = "internal";
- phy-handle = <&phy_port2>;
- };
-
- port@3 {
- reg = <3>;
- label = "lan3";
- phy-mode = "internal";
- phy-handle = <&phy_port3>;
- };
-
- port@4 {
- reg = <4>;
- label = "lan4";
- phy-mode = "internal";
- phy-handle = <&phy_port4>;
- };
-
- port@5 {
- reg = <5>;
- label = "wan";
- phy-mode = "internal";
- phy-handle = <&phy_port5>;
- };
-
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&gmac2>;
- phy-mode = "sgmii";
- qca,sgmii-enable-pll;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy_port1: phy@0 {
- reg = <0>;
- };
-
- phy_port2: phy@1 {
- reg = <1>;
- };
-
- phy_port3: phy@2 {
- reg = <2>;
- };
-
- phy_port4: phy@3 {
- reg = <3>;
- };
-
- phy_port5: phy@4 {
- reg = <4>;
- };
- };
- };
-};
-
-&gmac1 {
- status = "okay";
-
- pinctrl-0 = <&rgmii2_pins>;
- pinctrl-names = "default";
-
- phy-mode = "rgmii";
- qcom,id = <1>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gmac2 {
- status = "okay";
-
- phy-mode = "sgmii";
- qcom,id = <2>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
-};
-
-&gsbi4_serial {
- pinctrl-0 = <&uart0_pins>;
- pinctrl-names = "default";
-};
-
-&flash {
- compatible = "jedec,spi-nor";
-};
-
-&sata_phy {
- status = "disabled";
-};
-
-&sata {
- status = "disabled";
-};
-
-&hs_phy_0 {
- status = "okay";
-};
-
-&ss_phy_0 {
- status = "okay";
-
- rx_eq = <2>;
- tx_deamp_3_5db = <32>;
- mpll = <160>;
-};
-
-&usb3_0 {
- status = "okay";
-};
-
-&hs_phy_1 {
- status = "okay";
-};
-
-&ss_phy_1 {
- status = "okay";
-
- rx_eq = <2>;
- tx_deamp_3_5db = <32>;
- mpll = <160>;
-};
-
-&usb3_1 {
- status = "okay";
-};
-
-&pcie0 {
- status = "okay";
-
- /delete-property/ pinctrl-0;
- /delete-property/ pinctrl-names;
- /delete-property/ perst-gpios;
-};
-
-&pcie1 {
- status = "okay";
-};
-
-&pcie2 {
- status = "okay";
-
- /delete-property/ pinctrl-0;
- /delete-property/ pinctrl-names;
- /delete-property/ perst-gpios;
-};
-
-&qcom_pinmux {
- pinctrl-names = "default";
- pinctrl-0 = <&state_default>;
-
- state_default: pinctrl0 {
- pcie0_pcie2_perst {
- pins = "gpio3";
- function = "gpio";
- drive-strength = <2>;
- bias-disable;
- output-high;
- };
- };
-
- led_pins: led_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9", "gpio22",
- "gpio23", "gpio24", "gpio25", "gpio53";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- button_pins: button_pins {
- mux {
- pins = "gpio54";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- beeper_pins: beeper_pins {
- mux {
- pins = "gpio55";
- function = "gpio";
- drive-strength = <2>;
- bias-pull-up;
- };
- };
-
- rpm_pins: rpm_pins {
- mux {
- pins = "gpio12", "gpio13";
- function = "gsbi4";
- drive-strength = <10>;
- bias-disable;
- };
- };
-
- uart0_pins: uart0_pins {
- mux {
- pins = "gpio10", "gpio11";
- function = "gsbi4";
- drive-strength = <10>;
- bias-disable;
- };
- };
-
- spi_pins: spi_pins {
- mux {
- pins = "gpio18", "gpio19";
- function = "gsbi5";
- drive-strength = <10>;
- bias-pull-down;
- };
-
- clk {
- pins = "gpio21";
- function = "gsbi5";
- drive-strength = <12>;
- bias-pull-down;
- };
-
- cs {
- pins = "gpio20";
- function = "gpio";
- drive-strength = <10>;
- bias-pull-up;
- };
- };
-};
-
-&tcsr {
- qcom,usb-ctrl-select = <TCSR_USB_SELECT_USB3_DUAL>;
-};
projects / openwrt / openwrt.git / blobdiff