sunxi: 6.6: remove upstreamed patches

[openwrt/staging/blocktrron.git] / target / linux / sunxi / patches-6.6 / 004-v6.2-arm64-dts-allwinner-h616-OrangePi-Zero-2-Add-USB-nodes.patch

diff --git a/target/linux/sunxi/patches-6.6/004-v6.2-arm64-dts-allwinner-h616-OrangePi-Zero-2-Add-USB-nodes.patch b/target/linux/sunxi/patches-6.6/004-v6.2-arm64-dts-allwinner-h616-OrangePi-Zero-2-Add-USB-nodes.patch
deleted file mode 100644 (file)
index a544e48..0000000
--- a/target/linux/sunxi/patches-6.6/004-v6.2-arm64-dts-allwinner-h616-OrangePi-Zero-2-Add-USB-nodes.patch
+++ /dev/null
@@ -1,81 +0,0 @@
-From db5f028309ede13767e2ba356c1975ac37a4fd6c Mon Sep 17 00:00:00 2001
-From: Andre Przywara <andre.przywara@arm.com>
-Date: Mon, 31 Oct 2022 11:13:57 +0000
-Subject: [PATCH] arm64: dts: allwinner: h616: OrangePi Zero 2: Add USB nodes
-
-The OrangePi Zero 2 has one USB-A host port, VBUS is provided by
-a GPIO controlled regulator.
-The USB-C port is meant to power the board, but is also connected to
-the USB 0 port, which we configure as an MUSB peripheral.
-
-Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
-Link: https://lore.kernel.org/r/20221031111358.3387297-7-andre.przywara@arm.com
-Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
----
- .../allwinner/sun50i-h616-orangepi-zero2.dts  | 41 +++++++++++++++++++
- 1 file changed, 41 insertions(+)
-
---- a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
-+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
-@@ -49,8 +49,24 @@
-               regulator-max-microvolt = <5000000>;
-               regulator-always-on;
-       };
-+
-+      reg_usb1_vbus: regulator-usb1-vbus {
-+              compatible = "regulator-fixed";
-+              regulator-name = "usb1-vbus";
-+              regulator-min-microvolt = <5000000>;
-+              regulator-max-microvolt = <5000000>;
-+              vin-supply = <&reg_vcc5v>;
-+              enable-active-high;
-+              gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
-+      };
-+};
-+
-+&ehci1 {
-+      status = "okay";
- };
- 
-+/* USB 2 & 3 are on headers only. */
-+
- &emac0 {
-       pinctrl-names = "default";
-       pinctrl-0 = <&ext_rgmii_pins>;
-@@ -76,6 +92,10 @@
-       status = "okay";
- };
- 
-+&ohci1 {
-+      status = "okay";
-+};
-+
- &r_rsb {
-       status = "okay";
- 
-@@ -211,3 +231,24 @@
-       pinctrl-0 = <&uart0_ph_pins>;
-       status = "okay";
- };
-+
-+&usbotg {
-+      /*
-+       * PHY0 pins are connected to a USB-C socket, but a role switch
-+       * is not implemented: both CC pins are pulled to GND.
-+       * The VBUS pins power the device, so a fixed peripheral mode
-+       * is the best choice.
-+       * The board can be powered via GPIOs, in this case port0 *can*
-+       * act as a host (with a cable/adapter ignoring CC), as VBUS is
-+       * then provided by the GPIOs. Any user of this setup would
-+       * need to adjust the DT accordingly: dr_mode set to "host",
-+       * enabling OHCI0 and EHCI0.
-+       */
-+      dr_mode = "peripheral";
-+      status = "okay";
-+};
-+
-+&usbphy {
-+      usb1_vbus-supply = <&reg_usb1_vbus>;
-+      status = "okay";
-+};