X-Git-Url: http://git.openwrt.org/?a=blobdiff_plain;f=target%2Flinux%2Fifxmips%2Ffiles-2.6.33%2Farch%2Fmips%2Finclude%2Fasm%2Fmach-ifxmips%2Fifxmips_gptu.h;fp=target%2Flinux%2Fifxmips%2Ffiles-2.6.33%2Farch%2Fmips%2Finclude%2Fasm%2Fmach-ifxmips%2Fifxmips_gptu.h;h=330c3cfd55bdb90a57f78c87b9fb65f7bfb8ff27;hb=c54867d4916de29b2e0d15da222677522a8acc52;hp=0000000000000000000000000000000000000000;hpb=cfb1bf79f93524eb11f471dad57478baacc055cb;p=openwrt%2Fsvn-archive%2Farchive.git diff --git a/target/linux/ifxmips/files-2.6.33/arch/mips/include/asm/mach-ifxmips/ifxmips_gptu.h b/target/linux/ifxmips/files-2.6.33/arch/mips/include/asm/mach-ifxmips/ifxmips_gptu.h new file mode 100644 index 0000000000..330c3cfd55 --- /dev/null +++ b/target/linux/ifxmips/files-2.6.33/arch/mips/include/asm/mach-ifxmips/ifxmips_gptu.h @@ -0,0 +1,155 @@ +#ifndef __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ +#define __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ + + +/****************************************************************************** + Copyright (c) 2002, Infineon Technologies. All rights reserved. + + No Warranty + Because the program is licensed free of charge, there is no warranty for + the program, to the extent permitted by applicable law. Except when + otherwise stated in writing the copyright holders and/or other parties + provide the program "as is" without warranty of any kind, either + expressed or implied, including, but not limited to, the implied + warranties of merchantability and fitness for a particular purpose. The + entire risk as to the quality and performance of the program is with + you. should the program prove defective, you assume the cost of all + necessary servicing, repair or correction. + + In no event unless required by applicable law or agreed to in writing + will any copyright holder, or any other party who may modify and/or + redistribute the program as permitted above, be liable to you for + damages, including any general, special, incidental or consequential + damages arising out of the use or inability to use the program + (including but not limited to loss of data or data being rendered + inaccurate or losses sustained by you or third parties or a failure of + the program to operate with any other programs), even if such holder or + other party has been advised of the possibility of such damages. +******************************************************************************/ + + +/* + * #################################### + * Definition + * #################################### + */ + +/* + * Available Timer/Counter Index + */ +#define TIMER(n, X) (n * 2 + (X ? 1 : 0)) +#define TIMER_ANY 0x00 +#define TIMER1A TIMER(1, 0) +#define TIMER1B TIMER(1, 1) +#define TIMER2A TIMER(2, 0) +#define TIMER2B TIMER(2, 1) +#define TIMER3A TIMER(3, 0) +#define TIMER3B TIMER(3, 1) + +/* + * Flag of Timer/Counter + * These flags specify the way in which timer is configured. + */ +/* Bit size of timer/counter. */ +#define TIMER_FLAG_16BIT 0x0000 +#define TIMER_FLAG_32BIT 0x0001 +/* Switch between timer and counter. */ +#define TIMER_FLAG_TIMER 0x0000 +#define TIMER_FLAG_COUNTER 0x0002 +/* Stop or continue when overflowing/underflowing. */ +#define TIMER_FLAG_ONCE 0x0000 +#define TIMER_FLAG_CYCLIC 0x0004 +/* Count up or counter down. */ +#define TIMER_FLAG_UP 0x0000 +#define TIMER_FLAG_DOWN 0x0008 +/* Count on specific level or edge. */ +#define TIMER_FLAG_HIGH_LEVEL_SENSITIVE 0x0000 +#define TIMER_FLAG_LOW_LEVEL_SENSITIVE 0x0040 +#define TIMER_FLAG_RISE_EDGE 0x0010 +#define TIMER_FLAG_FALL_EDGE 0x0020 +#define TIMER_FLAG_ANY_EDGE 0x0030 +/* Signal is syncronous to module clock or not. */ +#define TIMER_FLAG_UNSYNC 0x0000 +#define TIMER_FLAG_SYNC 0x0080 +/* Different interrupt handle type. */ +#define TIMER_FLAG_NO_HANDLE 0x0000 +#if defined(__KERNEL__) + #define TIMER_FLAG_CALLBACK_IN_IRQ 0x0100 +#endif // defined(__KERNEL__) +#define TIMER_FLAG_SIGNAL 0x0300 +/* Internal clock source or external clock source */ +#define TIMER_FLAG_INT_SRC 0x0000 +#define TIMER_FLAG_EXT_SRC 0x1000 + + +/* + * ioctl Command + */ +#define GPTU_REQUEST_TIMER 0x01 /* General method to setup timer/counter. */ +#define GPTU_FREE_TIMER 0x02 /* Free timer/counter. */ +#define GPTU_START_TIMER 0x03 /* Start or resume timer/counter. */ +#define GPTU_STOP_TIMER 0x04 /* Suspend timer/counter. */ +#define GPTU_GET_COUNT_VALUE 0x05 /* Get current count value. */ +#define GPTU_CALCULATE_DIVIDER 0x06 /* Calculate timer divider from given freq.*/ +#define GPTU_SET_TIMER 0x07 /* Simplified method to setup timer. */ +#define GPTU_SET_COUNTER 0x08 /* Simplified method to setup counter. */ + +/* + * Data Type Used to Call ioctl + */ +struct gptu_ioctl_param { + unsigned int timer; /* In command GPTU_REQUEST_TIMER, GPTU_SET_TIMER, and * + * GPTU_SET_COUNTER, this field is ID of expected * + * timer/counter. If it's zero, a timer/counter would * + * be dynamically allocated and ID would be stored in * + * this field. * + * In command GPTU_GET_COUNT_VALUE, this field is * + * ignored. * + * In other command, this field is ID of timer/counter * + * allocated. */ + unsigned int flag; /* In command GPTU_REQUEST_TIMER, GPTU_SET_TIMER, and * + * GPTU_SET_COUNTER, this field contains flags to * + * specify how to configure timer/counter. * + * In command GPTU_START_TIMER, zero indicate start * + * and non-zero indicate resume timer/counter. * + * In other command, this field is ignored. */ + unsigned long value; /* In command GPTU_REQUEST_TIMER, this field contains * + * init/reload value. * + * In command GPTU_SET_TIMER, this field contains * + * frequency (0.001Hz) of timer. * + * In command GPTU_GET_COUNT_VALUE, current count * + * value would be stored in this field. * + * In command GPTU_CALCULATE_DIVIDER, this field * + * contains frequency wanted, and after calculation, * + * divider would be stored in this field to overwrite * + * the frequency. * + * In other command, this field is ignored. */ + int pid; /* In command GPTU_REQUEST_TIMER and GPTU_SET_TIMER, * + * if signal is required, this field contains process * + * ID to which signal would be sent. * + * In other command, this field is ignored. */ + int sig; /* In command GPTU_REQUEST_TIMER and GPTU_SET_TIMER, * + * if signal is required, this field contains signal * + * number which would be sent. * + * In other command, this field is ignored. */ +}; + +/* + * #################################### + * Data Type + * #################################### + */ +typedef void (*timer_callback)(unsigned long arg); + +extern int ifxmips_request_timer(unsigned int, unsigned int, unsigned long, unsigned long, unsigned long); +extern int ifxmips_free_timer(unsigned int); +extern int ifxmips_start_timer(unsigned int, int); +extern int ifxmips_stop_timer(unsigned int); +extern int ifxmips_reset_counter_flags(u32 timer, u32 flags); +extern int ifxmips_get_count_value(unsigned int, unsigned long *); +extern u32 ifxmips_cal_divider(unsigned long); +extern int ifxmips_set_timer(unsigned int, unsigned int, int, int, unsigned int, unsigned long, unsigned long); +extern int ifxmips_set_counter(unsigned int timer, unsigned int flag, + u32 reload, unsigned long arg1, unsigned long arg2); + +#endif /* __DANUBE_GPTU_DEV_H__2005_07_26__10_19__ */