mvebu: add support for Fortinet FortiGate 50E

Fortinet FortiGate 50E (FG-50E) is a UTM, based on Armada 385 (88F6820).

Specification:

- SoC          : Marvell Armada 385 88F6820
- RAM          : DDR3 2 GiB (4x Micron MT41K512M8DA-107, "D9SGQ")
- Flash        : SPI-NOR 128 MiB (Macronix MX66L1G45GMI-10G)
- Ethernet     : 7x 10/100/1000 Mbps
  - LAN 1-5    : Marvell 88E6176
  - WAN 1, 2   : Marvell 88E1512 (2x)
- LEDs/Keys    : 18x/1x
- UART         : "CONSOLE" port (RJ-45, RS-232C level)
  - port       : ttyS0
  - settings   : 9600bps 8n1
  - assignment : 1:NC , 2:NC , 3:TXD, 4:GND,
                 5:GND, 6:RXD, 7:NC , 8:NC
  - note       : compatible with Cisco console cable
- HW Monitoring: nuvoTon NCT7802Y
- Power        : 12 VDC, 2 A
  - plug       : Molex 5557-02R

Flash instruction using initramfs image:

1. Power on FG-50E and interrupt to show bootmenu
2. Call "[R]: Review TFTP parameters.", check TFTP parameters and
   connect computer to "Image download port" in the parameters
3. Prepare TFTP server with the parameters obtained above
4. Rename OpenWrt initramfs image to "image.out" and put to TFTP
   directory
5. Call "[T]: Initiate TFTP firmware transfer." to download initramfs
   image from TFTP server
6. Type "r" key when the following message is showed, to boot initramfs
   image without flashing to spi-nor flash

   "Save as Default firmware/Backup firmware/Run image without saving:[D/B/R]?"

7. On initramfs image, backup mtd if needed

   minimum:

   - "firmware-info"
   - "kernel"
   - "rootfs"

7. On initramfs image, upload sysupgrade image to the device and perform
   sysupgrade
8. Wait ~200 seconds to complete flashing and rebooting.
   If the device is booted with stock firmware, login to bootmenu and
   call "[B]: Boot with backup firmware and set as default." to set the
   first OS image as default and boot it.

Notes:

- All "SPEED" LEDs(Green/Amber) of LAN and 1000M "SPEED" LEDs(Green) of
  WAN1/2 are connected to GPIO expander. There is no way to indicate
  link speed of networking device on Linux Kernel/OpenWrt, so those LEDs
  cannot be handled like stock firmware.
  On OpenWrt, use netdev(link) trigger instead.

- Both colors of Bi-color LEDs on the front panel cannot be turned on at
  the same time.

- "PWR" and "Logo" LEDs are connected to power source directly.

- The following partitions are added for OpenWrt.
  These partitions are contained in "uboot" partition (0x0-0x1fffff) on
  stock firmware.

  - "firmware-info"
  - "dtb"
  - "u-boot-env"
  - "board-info"

Image header for bootmenu tftp:

  0x0 - 0xf  : ?
 0x10 - 0x2f : Image Name
 0x30 - 0x17f: ?
0x180 - 0x183: Kernel Offset*
0x184 - 0x187: Kernel Length*
0x188 - 0x18b: RootFS Offset (ext2)*
0x18c - 0x18f: RootFS Length (ext2)*
0x190 - 0x193: DTB Offset
0x194 - 0x197: DTB Length
0x198 - 0x19b: Data Offset (jffs2)
0x19c - 0x19f: Data Length (jffs2)
0x1a0 - 0x1ff: ?

*: required for initramfs image

MAC addresses:

(eth0): 70:4C:A5:xx:xx:7C (board-info, 0xd880 (hex))
WAN 1 : 70:4C:A5:xx:xx:7D
WAN 2 : 70:4C:A5:xx:xx:7E
LAN 1 : 70:4C:A5:xx:xx:7F
LAN 2 : 70:4C:A5:xx:xx:80
LAN 3 : 70:4C:A5:xx:xx:81
LAN 4 : 70:4C:A5:xx:xx:82
LAN 5 : 70:4C:A5:xx:xx:83

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>

diff --git a/target/linux/mvebu/cortexa9/base-files/etc/board.d/01_leds b/target/linux/mvebu/cortexa9/base-files/etc/board.d/01_leds
index 2b045d094574420f292739d95c2fccdbf50eed06..bfc589e6c01cbfc63e680b3bee9e19ce2ccf548b 100644 (file)
--- a/target/linux/mvebu/cortexa9/base-files/etc/board.d/01_leds
+++ b/target/linux/mvebu/cortexa9/base-files/etc/board.d/01_leds
@@ -15,6 +15,15 @@ ctera,c200-v2)
        ucidef_set_led_usbport "usb2" "USB2" "green:usb-2" "usb1-port1" "usb2-port1"
        ucidef_set_led_usbport "usb3" "USB3" "green:usb-1" "usb1-port2" "usb2-port2"
        ;;
+fortinet,fg-50e)
+       ucidef_set_led_netdev "wan1_link" "WAN1 Link" "green:speed_wan1" "eth1" "link"
+       ucidef_set_led_netdev "wan2_link" "WAN2 Link" "green:speed_wan2" "eth2" "link"
+       ucidef_set_led_netdev "lan1_link" "LAN1 Link" "green:speed_lan1" "lan1" "link"
+       ucidef_set_led_netdev "lan2_link" "LAN2 Link" "green:speed_lan2" "lan2" "link"
+       ucidef_set_led_netdev "lan3_link" "LAN3 Link" "green:speed_lan3" "lan3" "link"
+       ucidef_set_led_netdev "lan4_link" "LAN4 Link" "green:speed_lan4" "lan4" "link"
+       ucidef_set_led_netdev "lan5_link" "LAN5 Link" "green:speed_lan5" "lan5" "link"
+       ;;
 kobol,helios4)
        ucidef_set_led_usbport "USB" "USB" "helios4:green:usb" "usb1-port1" "usb2-port1" "usb3-port1" "usb4-port1" "usb5-port1"
        ;;

diff --git a/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network b/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network
index d2229fe6bfbc329dde7c22700c5f489a205c1ecf..9db29d52df5a6a9abdf1e70ae7b1dfac0e0084de 100644 (file)
--- a/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network
+++ b/target/linux/mvebu/cortexa9/base-files/etc/board.d/02_network
@@ -18,6 +18,9 @@ mvebu_setup_interfaces()
        cznic,turris-omnia)
                ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3 lan4" "eth2"
                ;;
+       fortinet,fg-50e)
+               ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5" "eth1 eth2"
+               ;;
        iptime,nas1dual)
                ucidef_set_interface_lan "eth0 eth1" "dhcp"
                ;;

diff --git a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/fortinet.sh b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/fortinet.sh
new file mode 100644 (file)
index 0000000..a2742aa
--- /dev/null
+++ b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/fortinet.sh
@@ -0,0 +1,54 @@
+. /lib/functions.sh
+
+fortinet_fwinfo_blocks() {
+       local fwinfo_mtd="$(find_mtd_part firmware-info)"
+       local offset="$1"
+       local len="$2"
+       local blks
+
+       if [ -z "$fwinfo_mtd" ]; then
+               echo "WARN: MTD device \"firmware-info\" not found"
+               return 1
+       fi
+
+       blks=$((len / 0x200))
+       [ $((len % 0x200)) -gt 0 ] && blks=$((blks + 1))
+       blks=$(printf "%04x" $blks)
+       printf "fwinfo: offset-> 0x%x, blocks-> 0x%s (len: 0x%08x)\n" \
+               $offset $blks $len
+
+       printf "\x${blks:2:2}\x${blks:0:2}" | \
+               dd bs=2 count=1 seek=$((offset / 2)) conv=notrunc of=${fwinfo_mtd}
+}
+
+fortinet_do_upgrade() {
+       local board_dir="$(tar tf "$1" | grep -m 1 '^sysupgrade-.*/$')"
+       local kern_mtd="$(find_mtd_part kernel)"
+       local root_mtd="$(find_mtd_part rootfs)"
+       local kern_len root_len
+
+       board_dir="${board_dir%/}"
+
+       if [ -z "$kern_mtd" ] || [ -z "$root_mtd" ]; then
+               echo "ERROR: MTD device \"kernel\" or \"rootfs\" not found"
+               umount -a
+               reboot -f
+       fi
+
+       kern_len=$( (tar xOf "$1" "$board_dir/kernel" | wc -c) 2> /dev/null)
+       root_len=$( (tar xOf "$1" "$board_dir/root" | wc -c) 2> /dev/null)
+
+       if [ -z "$kern_len" ] || [ -z "$root_len" ]; then
+               echo "ERROR: failed to get length of new kernel or rootfs"
+               umount -a
+               reboot -f
+       fi
+
+       fortinet_fwinfo_blocks "0x184" "$kern_len"
+       fortinet_fwinfo_blocks "0x18c" "$root_len"
+
+       tar xOf "$1" "$board_dir/kernel" | \
+               mtd write - "kernel"
+       tar xOf "$1" "$board_dir/root" | \
+               mtd ${UPGRADE_BACKUP:+-j "${UPGRADE_BACKUP}"} write - "rootfs"
+}

diff --git a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
index 9019c1aeff5c1fa6ff14d5d4a70551194dbdc69d..fbbb68e05eb93df023d287d9de837c0d0e90d4a3 100755 (executable)
--- a/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
+++ b/target/linux/mvebu/cortexa9/base-files/lib/upgrade/platform.sh
@@ -52,6 +52,9 @@ platform_do_upgrade() {
        solidrun,clearfog-pro-a1)
                legacy_sdcard_do_upgrade "$1"
                ;;
+       fortinet,fg-50e)
+               fortinet_do_upgrade "$1"
+               ;;
        linksys,wrt1200ac|\
        linksys,wrt1900ac-v1|\
        linksys,wrt1900ac-v2|\

diff --git a/target/linux/mvebu/files/arch/arm/boot/dts/armada-385-fortinet-fg-50e.dts b/target/linux/mvebu/files/arch/arm/boot/dts/armada-385-fortinet-fg-50e.dts
new file mode 100644 (file)
index 0000000..506e01f
--- /dev/null
+++ b/target/linux/mvebu/files/arch/arm/boot/dts/armada-385-fortinet-fg-50e.dts
@@ -0,0 +1,491 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include "armada-385.dtsi"
+
+/ {
+       model = "Fortinet FortiGate 50E";
+       compatible = "fortinet,fg-50e", "marvell,armada385", "marvell,armada380";
+
+       aliases {
+               led-boot = &led_status_green;
+               led-failsafe = &led_status_red;
+               led-running = &led_status_green;
+               led-upgrade = &led_status_green;
+               label-mac-device = &eth0;
+       };
+
+       chosen {
+               stdout-path = "serial0:9600n8";
+       };
+
+       memory@0 {
+               device_type = "memory";
+               reg = <0x00000000 0x80000000>; /* 2GB */
+       };
+
+       soc {
+               ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+                         MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+                         MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+                         MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+                         MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
+       };
+
+       gpio-keys {
+               compatible = "gpio-keys";
+               pinctrl-names = "default";
+               pinctrl-0 = <&pmx_gpio_keys_pins>;
+
+               reset {
+                       label = "reset";
+                       linux,code = <KEY_RESTART>;
+                       gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
+               };
+       };
+
+       gpio-leds {
+               compatible = "gpio-leds";
+               pinctrl-names = "default";
+               pinctrl-0 = <&pmx_gpio_leds_pins>;
+
+               led-0 {
+                       label = "red:alarm";
+                       gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_RED>;
+                       function = LED_FUNCTION_ALARM;
+               };
+
+               led-1 {
+                       label = "red:ha";
+                       gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_RED>;
+               };
+
+               led_status_green: led-2 {
+                       label = "green:sta";
+                       gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_GREEN>;
+                       function = LED_FUNCTION_STATUS;
+               };
+
+               led-3 {
+                       label = "green:ha";
+                       gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_GREEN>;
+               };
+
+               led-4 {
+                       label = "amber:alarm";
+                       gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_AMBER>;
+                       function = LED_FUNCTION_ALARM;
+               };
+
+               led_status_red: led-5 {
+                       label = "red:sta";
+                       gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_RED>;
+                       function = LED_FUNCTION_STATUS;
+               };
+
+               led-6 {
+                       label = "green:speed_wan1";
+                       gpios = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+                       color = <LED_COLOR_ID_GREEN>;
+               };
+
+               led-7 {
+                       label = "green:speed_wan2";
+                       gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+                       color = <LED_COLOR_ID_GREEN>;
+               };
+
+               led-8 {
+                       label = "amber:speed_lan5";
+                       gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+                       color = <LED_COLOR_ID_AMBER>;
+               };
+
+               led-9 {
+                       label = "green:speed_lan5";
+                       gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+                       color = <LED_COLOR_ID_GREEN>;
+               };
+
+               led-10 {
+                       label = "green:speed_lan4";
+                       gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_GREEN>;
+               };
+
+               led-11 {
+                       label = "amber:speed_lan4";
+                       gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_AMBER>;
+               };
+
+               led-12 {
+                       label = "amber:speed_lan3";
+                       gpios = <&gpio2 6 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_AMBER>;
+               };
+
+               led-13 {
+                       label = "green:speed_lan3";
+                       gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_GREEN>;
+               };
+
+               led-14 {
+                       label = "green:speed_lan1";
+                       gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_GREEN>;
+               };
+
+               led-15 {
+                       label = "amber:speed_lan1";
+                       gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_AMBER>;
+               };
+
+               led-16 {
+                       label = "green:speed_lan2";
+                       gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_GREEN>;
+               };
+
+               led-17 {
+                       label = "amber:speed_lan2";
+                       gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
+                       color = <LED_COLOR_ID_AMBER>;
+               };
+       };
+
+       reg_usb_vbus: regulator-usb-vbus {
+               compatible = "fixed-regulator";
+               regulator-name = "usb-vbus";
+               regulator-min-microvolt = <5000000>;
+               regulator-max-microvolt = <5000000>;
+               gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
+               regulator-always-on;
+       };
+};
+
+&i2c0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&i2c0_pins>;
+       status = "okay";
+
+       gpio2: gpio@24 {
+               compatible = "nxp,pca9555";
+               reg = <0x24>;
+               gpio-controller;
+               #gpio-cells = <0x2>;
+       };
+
+       hwmon@28 {
+               compatible = "nuvoton,nct7802";
+               reg = <0x28>;
+       };
+};
+
+&uart0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart0_pins>;
+       status = "okay";
+};
+
+&pinctrl {
+       pmx_phy_switch_pins: phy-switch-pins {
+               marvell,pins = "mpp19", "mpp20", "mpp23", "mpp34", "mpp41";
+               marvell,function = "gpio";
+       };
+
+       pmx_gpio_leds_pins: gpio-leds-pins {
+               marvell,pins = "mpp30", "mpp32", "mpp33", "mpp35",
+                              "mpp45", "mpp47";
+               marvell,function = "gpio";
+       };
+
+       pmx_usb_pins: usb-pins {
+               marvell,pins = "mpp53";
+               marvell,function = "gpio";
+       };
+
+       pmx_gpio_keys_pins: gpio-keys-pins {
+               marvell,pins = "mpp54";
+               marvell,function = "gpio";
+       };
+};
+
+&bm {
+       status = "okay";
+};
+
+&bm_bppi {
+       status = "okay";
+};
+
+&eth0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&ge0_rgmii_pins>;
+       status = "okay";
+
+       phy-connection-type = "rgmii-id";
+       buffer-manager = <&bm>;
+       bm,pool-long = <0>;
+       bm,pool-short = <1>;
+       nvmem-cells = <&macaddr_bdinfo_d880>;
+       nvmem-cell-names = "mac-address";
+
+       fixed-link {
+               speed = <1000>;
+               full-duplex;
+       };
+};
+
+&eth1 {
+       status = "okay";
+
+       phy-handle = <&ethphy0>;
+       phy-connection-type = "sgmii";
+       buffer-manager = <&bm>;
+       bm,pool-long = <2>;
+       nvmem-cells = <&macaddr_bdinfo_d880>;
+       nvmem-cell-names = "mac-address";
+       mac-address-increment = <1>;
+};
+
+&eth2 {
+       status = "okay";
+
+       phy-handle = <&ethphy1>;
+       phy-connection-type = "sgmii";
+       buffer-manager = <&bm>;
+       bm,pool-long = <3>;
+       nvmem-cells = <&macaddr_bdinfo_d880>;
+       nvmem-cell-names = "mac-address";
+       mac-address-increment = <2>;
+};
+
+&mdio {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mdio_pins>, <&pmx_phy_switch_pins>;
+
+       /* Marvell 88E1512 */
+       ethphy0: ethernet-phy@0 {
+               compatible = "ethernet-phy-id0141,0dd1",
+                            "ethernet-phy-ieee802.3-c22";
+               reg = <0>;
+               interrupt-parent = <&gpio0>;
+               interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+               reset-gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
+               /*
+                * LINK/ACT   (Green): LED[0], Active Low
+                * SPEED 100M (Amber): LED[1], Active High
+                */
+               marvell,reg-init = <3 16 0 0x71>,
+                                  <3 17 0 0x4>;
+       };
+
+       /* Marvell 88E1512 */
+       ethphy1: ethernet-phy@1 {
+               compatible = "ethernet-phy-id0141,0dd1",
+                            "ethernet-phy-ieee802.3-c22";
+               reg = <1>;
+               interrupt-parent = <&gpio1>;
+               interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+               reset-gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+               /*
+                * LINK/ACT   (Green): LED[0], Active Low
+                * SPEED 100M (Amber): LED[1], Active High
+                */
+               marvell,reg-init = <3 16 0 0x71>,
+                                  <3 17 0 0x4>;
+       };
+
+       /* Marvell 88E6176 */
+       switch@2 {
+               compatible = "marvell,mv88e6085";
+               reg = <0x2>;
+               reset-gpios = <&gpio0 19 GPIO_ACTIVE_LOW>;
+
+               ports {
+                       #address-cells = <1>;
+                       #size-cells = <0>;
+
+                       port@0 {
+                               reg = <0>;
+                               label = "lan5";
+                               nvmem-cells = <&macaddr_bdinfo_d880>;
+                               nvmem-cell-names = "mac-address";
+                               mac-address-increment = <7>;
+                       };
+
+                       port@1 {
+                               reg = <1>;
+                               label = "lan4";
+                               nvmem-cells = <&macaddr_bdinfo_d880>;
+                               nvmem-cell-names = "mac-address";
+                               mac-address-increment = <6>;
+                       };
+
+                       port@2 {
+                               reg = <2>;
+                               label = "lan3";
+                               nvmem-cells = <&macaddr_bdinfo_d880>;
+                               nvmem-cell-names = "mac-address";
+                               mac-address-increment = <5>;
+                       };
+
+                       port@3 {
+                               reg = <3>;
+                               label = "lan2";
+                               nvmem-cells = <&macaddr_bdinfo_d880>;
+                               nvmem-cell-names = "mac-address";
+                               mac-address-increment = <4>;
+                       };
+
+                       port@4 {
+                               reg = <4>;
+                               label = "lan1";
+                               nvmem-cells = <&macaddr_bdinfo_d880>;
+                               nvmem-cell-names = "mac-address";
+                               mac-address-increment = <3>;
+                       };
+
+                       port@6 {
+                               reg = <6>;
+                               ethernet = <&eth0>;
+                               phy-connection-type = "rgmii-id";
+
+                               fixed-link {
+                                       speed = <1000>;
+                                       full-duplex;
+                               };
+                       };
+               };
+       };
+};
+
+&usb3_0 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&pmx_usb_pins>;
+       status = "okay";
+
+       vbus-supply = <&reg_usb_vbus>;
+};
+
+&spi1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&spi1_pins>;
+       status = "okay";
+
+       flash@0 {
+               compatible = "jedec,spi-nor";
+               reg = <0>;
+               spi-max-frequency = <50000000>;
+
+               partitions {
+                       compatible = "fixed-partitions";
+                       #address-cells = <1>;
+                       #size-cells = <1>;
+
+                       partition@0 {
+                               reg = <0x0 0x1c0000>;
+                               label = "u-boot";
+                               read-only;
+                       };
+
+                       partition@1c0000 {
+                               reg = <0x1c0000 0x10000>;
+                               label = "firmware-info";
+
+                               /*
+                                *  0x10 - 0x2f : image name (image1)
+                                *  0x30 - 0x4f : image name (image2)
+                                * 0x170 (1byte): active image (0x0/0x1)
+                                * 0x184 - 0x185: kernel block count (image1)
+                                * 0x18c - 0x18d: rootfs block count (image1)
+                                * 0x194 - 0x195: kernel block count (image2)
+                                * 0x19c - 0x19d: rootfs block count (image2)
+                                * 0x1be (1byte): bit7 -> active flag (image1)?
+                                * 0x1ce (1byte): bit7 -> active flag (image2)?
+                                *
+                                * Note: block size --> 0x200 (512 bytes)
+                                */
+                       };
+
+                       partition@1d0000 {
+                               reg = <0x1d0000 0x10000>;
+                               label = "dtb";
+                               read-only;
+                       };
+
+                       partition@1e0000 {
+                               reg = <0x1e0000 0x10000>;
+                               label = "u-boot-env";
+                               read-only;
+                       };
+
+                       partition@1f0000 {
+                               reg = <0x1f0000 0x10000>;
+                               label = "board-info";
+                               read-only;
+
+                               compatible = "nvmem-cells";
+                               #address-cells = <1>;
+                               #size-cells = <1>;
+
+                               macaddr_bdinfo_d880: macaddr@d880 {
+                                       reg = <0xd880 0x6>;
+                               };
+                       };
+
+                       partition@200000 {
+                               reg = <0x200000 0x600000>;
+                               label = "kernel";
+                       };
+
+                       partition@800000 {
+                               reg = <0x800000 0x1800000>;
+                               label = "rootfs";
+                       };
+
+                       partition@2000000 {
+                               reg = <0x2000000 0x600000>;
+                               label = "kn2";
+                               read-only;
+                       };
+
+                       partition@2600000 {
+                               reg = <0x2600000 0x1800000>;
+                               label = "rfs2";
+                               read-only;
+                       };
+
+                       partition@3e00000 {
+                               reg = <0x3e00000 0x1200000>;
+                               label = "part1";
+                               read-only;
+                       };
+
+                       partition@5000000 {
+                               reg = <0x5000000 0x1200000>;
+                               label = "part2";
+                               read-only;
+                       };
+
+                       partition@6200000 {
+                               reg = <0x6200000 0x1e00000>;
+                               label = "config";
+                               read-only;
+                       };
+               };
+       };
+};

diff --git a/target/linux/mvebu/image/cortexa9.mk b/target/linux/mvebu/image/cortexa9.mk
index 56381ab5f85e5813afa8a886eff5e8aa24b22420..248f1cd6fdfdabd6b60c90b84a93fb6429de67f9 100644 (file)
--- a/target/linux/mvebu/image/cortexa9.mk
+++ b/target/linux/mvebu/image/cortexa9.mk
@@ -3,6 +3,19 @@
 # Copyright (C) 2012-2016 OpenWrt.org
 # Copyright (C) 2016 LEDE-project.org
 
+define Build/fortigate-header
+  ( \
+    dd if=/dev/zero bs=384 count=1 2>/dev/null; \
+    datalen=$$(wc -c $@ | cut -d' ' -f1); \
+    datalen=$$(printf "%08x" $$datalen); \
+    datalen="$${datalen:6:2}$${datalen:4:2}$${datalen:2:2}$${datalen:0:2}"; \
+    printf $$(echo "00020000$${datalen}ffff0000ffff0000" | sed 's/../\\x&/g'); \
+    dd if=/dev/zero bs=112 count=1 2>/dev/null; \
+    cat $@; \
+  ) > $@.new
+  mv $@.new $@
+endef
+
 define Device/dsa-migration
   DEVICE_COMPAT_VERSION := 1.1
   DEVICE_COMPAT_MESSAGE := Config cannot be migrated from swconfig to DSA
@@ -84,6 +97,21 @@ define Device/cznic_turris-omnia
 endef
 TARGET_DEVICES += cznic_turris-omnia
 
+define Device/fortinet_fg-50e
+  DEVICE_VENDOR := Fortinet
+  DEVICE_MODEL := FortiGate 50E
+  SOC := armada-385
+  KERNEL := kernel-bin | append-dtb
+  KERNEL_INITRAMFS := kernel-bin | append-dtb | fortigate-header | \
+    gzip-filename FGT50E
+  KERNEL_SIZE := 6144k
+  DEVICE_DTS := armada-385-fortinet-fg-50e
+  IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \
+    sysupgrade-tar rootfs=$$$$@ | append-metadata
+  DEVICE_PACKAGES := kmod-hwmon-nct7802
+endef
+TARGET_DEVICES += fortinet_fg-50e
+
 define Device/globalscale_mirabox
   $(Device/NAND-512K)
   DEVICE_VENDOR := Globalscale