SUBTARGETS:=generic
KERNEL_PATCHVER:=4.19
+KERNEL_TESTING_PATCHVER:=5.4
KERNELNAME:=zImage Image dtbs
--- /dev/null
+CONFIG_64BIT_TIME=y
+# CONFIG_ADIN_PHY is not set
+CONFIG_ALIGNMENT_TRAP=y
+# CONFIG_AL_FIC is not set
+# CONFIG_APQ_GCC_8084 is not set
+# CONFIG_APQ_MMCC_8084 is not set
+CONFIG_AR40XX_PHY=y
+CONFIG_ARCH_32BIT_OFF_T=y
+CONFIG_ARCH_CLOCKSOURCE_DATA=y
+CONFIG_ARCH_HAS_BINFMT_FLAT=y
+CONFIG_ARCH_HAS_DEBUG_VIRTUAL=y
+CONFIG_ARCH_HAS_ELF_RANDOMIZE=y
+CONFIG_ARCH_HAS_FORTIFY_SOURCE=y
+CONFIG_ARCH_HAS_GCOV_PROFILE_ALL=y
+CONFIG_ARCH_HAS_KCOV=y
+CONFIG_ARCH_HAS_KEEPINITRD=y
+CONFIG_ARCH_HAS_MEMBARRIER_SYNC_CORE=y
+CONFIG_ARCH_HAS_PHYS_TO_DMA=y
+CONFIG_ARCH_HAS_SETUP_DMA_OPS=y
+CONFIG_ARCH_HAS_SET_MEMORY=y
+CONFIG_ARCH_HAS_STRICT_KERNEL_RWX=y
+CONFIG_ARCH_HAS_STRICT_MODULE_RWX=y
+CONFIG_ARCH_HAS_TEARDOWN_DMA_OPS=y
+CONFIG_ARCH_HAS_TICK_BROADCAST=y
+CONFIG_ARCH_HAVE_CUSTOM_GPIO_H=y
+CONFIG_ARCH_HIBERNATION_POSSIBLE=y
+CONFIG_ARCH_IPQ40XX=y
+CONFIG_ARCH_KEEP_MEMBLOCK=y
+# CONFIG_ARCH_MDM9615 is not set
+CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y
+# CONFIG_ARCH_MILBEAUT is not set
+# CONFIG_ARCH_MSM8960 is not set
+# CONFIG_ARCH_MSM8974 is not set
+# CONFIG_ARCH_MSM8X60 is not set
+CONFIG_ARCH_MULTIPLATFORM=y
+CONFIG_ARCH_MULTI_V6_V7=y
+CONFIG_ARCH_MULTI_V7=y
+CONFIG_ARCH_NR_GPIO=0
+CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y
+CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y
+CONFIG_ARCH_QCOM=y
+# CONFIG_ARCH_RDA is not set
+CONFIG_ARCH_SUPPORTS_ATOMIC_RMW=y
+CONFIG_ARCH_SUPPORTS_BIG_ENDIAN=y
+CONFIG_ARCH_SUPPORTS_UPROBES=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_ARCH_USE_BUILTIN_BSWAP=y
+CONFIG_ARCH_USE_CMPXCHG_LOCKREF=y
+CONFIG_ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT=y
+CONFIG_ARCH_WANT_GENERAL_HUGETLB=y
+CONFIG_ARCH_WANT_IPC_PARSE_VERSION=y
+CONFIG_ARM=y
+CONFIG_ARM_AMBA=y
+CONFIG_ARM_APPENDED_DTB=y
+CONFIG_ARM_ARCH_TIMER=y
+CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y
+# CONFIG_ARM_ATAG_DTB_COMPAT is not set
+CONFIG_ARM_CPUIDLE=y
+CONFIG_ARM_CPU_SUSPEND=y
+# CONFIG_ARM_CPU_TOPOLOGY is not set
+# CONFIG_ARM_ERRATA_814220 is not set
+# CONFIG_ARM_ERRATA_857271 is not set
+# CONFIG_ARM_ERRATA_857272 is not set
+CONFIG_ARM_GIC=y
+CONFIG_ARM_HAS_SG_CHAIN=y
+CONFIG_ARM_L1_CACHE_SHIFT=6
+CONFIG_ARM_L1_CACHE_SHIFT_6=y
+# CONFIG_ARM_LPAE is not set
+CONFIG_ARM_PATCH_IDIV=y
+CONFIG_ARM_PATCH_PHYS_VIRT=y
+# CONFIG_ARM_QCOM_CPUFREQ_HW is not set
+# CONFIG_ARM_SMMU is not set
+# CONFIG_ARM_SP805_WATCHDOG is not set
+CONFIG_ARM_THUMB=y
+# CONFIG_ARM_THUMBEE is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_ARM_VIRT_EXT=y
+CONFIG_AT803X_PHY=y
+CONFIG_AUTO_ZRELADDR=y
+# CONFIG_BACKLIGHT_CLASS_DEVICE is not set
+CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_MQ_PCI=y
+CONFIG_BOUNCE=y
+# CONFIG_CACHE_L2X0 is not set
+CONFIG_CC_CAN_LINK=y
+CONFIG_CC_HAS_ASM_INLINE=y
+CONFIG_CC_HAS_KASAN_GENERIC=y
+CONFIG_CC_HAS_WARN_MAYBE_UNINITIALIZED=y
+# CONFIG_CHARGER_LT3651 is not set
+# CONFIG_CHARGER_UCS1002 is not set
+CONFIG_CLKDEV_LOOKUP=y
+CONFIG_CLKSRC_QCOM=y
+CONFIG_CLONE_BACKWARDS=y
+CONFIG_COMMON_CLK=y
+# CONFIG_COMMON_CLK_FIXED_MMIO is not set
+CONFIG_COMMON_CLK_QCOM=y
+# CONFIG_COMMON_CLK_SI5341 is not set
+CONFIG_COMPAT_32BIT_TIME=y
+# CONFIG_COUNTER is not set
+CONFIG_CPUFREQ_DT=y
+CONFIG_CPUFREQ_DT_PLATDEV=y
+CONFIG_CPU_32v6K=y
+CONFIG_CPU_32v7=y
+CONFIG_CPU_ABRT_EV7=y
+# CONFIG_CPU_BIG_ENDIAN is not set
+# CONFIG_CPU_BPREDICT_DISABLE is not set
+CONFIG_CPU_CACHE_V7=y
+CONFIG_CPU_CACHE_VIPT=y
+CONFIG_CPU_COPY_V6=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
+# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set
+CONFIG_CPU_FREQ_GOV_ATTR_SET=y
+CONFIG_CPU_FREQ_GOV_COMMON=y
+# CONFIG_CPU_FREQ_GOV_CONSERVATIVE is not set
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
+# CONFIG_CPU_FREQ_GOV_POWERSAVE is not set
+# CONFIG_CPU_FREQ_GOV_USERSPACE is not set
+CONFIG_CPU_FREQ_STAT=y
+CONFIG_CPU_HAS_ASID=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_ICACHE_MISMATCH_WORKAROUND is not set
+CONFIG_CPU_IDLE=y
+CONFIG_CPU_IDLE_GOV_LADDER=y
+CONFIG_CPU_IDLE_GOV_MENU=y
+# CONFIG_CPU_IDLE_GOV_TEO is not set
+CONFIG_CPU_IDLE_MULTIPLE_DRIVERS=y
+CONFIG_CPU_PABRT_V7=y
+CONFIG_CPU_PM=y
+CONFIG_CPU_RMAP=y
+CONFIG_CPU_SPECTRE=y
+CONFIG_CPU_THERMAL=y
+CONFIG_CPU_THUMB_CAPABLE=y
+CONFIG_CPU_TLB_V7=y
+CONFIG_CPU_V7=y
+CONFIG_CRC16=y
+# CONFIG_CRC32_SARWATE is not set
+CONFIG_CRC32_SLICEBY8=y
+CONFIG_CRYPTO_ACOMP2=y
+# CONFIG_CRYPTO_ADIANTUM is not set
+CONFIG_CRYPTO_AEAD=y
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_AKCIPHER2=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_CTR=y
+CONFIG_CRYPTO_DEFLATE=y
+CONFIG_CRYPTO_DES=y
+# CONFIG_CRYPTO_DEV_ATMEL_SHA204A is not set
+CONFIG_CRYPTO_DEV_QCE=y
+CONFIG_CRYPTO_DEV_QCOM_RNG=y
+CONFIG_CRYPTO_DRBG=y
+CONFIG_CRYPTO_DRBG_HMAC=y
+CONFIG_CRYPTO_DRBG_MENU=y
+CONFIG_CRYPTO_ECB=y
+# CONFIG_CRYPTO_ECRDSA is not set
+# CONFIG_CRYPTO_ESSIV is not set
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_HASH_INFO=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_HW=y
+CONFIG_CRYPTO_JITTERENTROPY=y
+CONFIG_CRYPTO_KPP2=y
+CONFIG_CRYPTO_LIB_AES=y
+CONFIG_CRYPTO_LIB_DES=y
+CONFIG_CRYPTO_LIB_SHA256=y
+CONFIG_CRYPTO_LZO=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_NULL=y
+CONFIG_CRYPTO_NULL2=y
+# CONFIG_CRYPTO_OFB is not set
+CONFIG_CRYPTO_RNG=y
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_RNG_DEFAULT=y
+CONFIG_CRYPTO_SEQIV=y
+CONFIG_CRYPTO_SHA256=y
+# CONFIG_CRYPTO_STREEBOG is not set
+CONFIG_CRYPTO_XTS=y
+# CONFIG_CRYPTO_XXHASH is not set
+CONFIG_CRYPTO_ZSTD=y
+CONFIG_DCACHE_WORD_ACCESS=y
+CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S"
+CONFIG_DEBUG_MISC=y
+# CONFIG_DEBUG_PLIST is not set
+# CONFIG_DEBUG_USER is not set
+# CONFIG_DMABUF_SELFTESTS is not set
+CONFIG_DMADEVICES=y
+CONFIG_DMA_DECLARE_COHERENT=y
+CONFIG_DMA_ENGINE=y
+CONFIG_DMA_OF=y
+CONFIG_DMA_REMAP=y
+CONFIG_DMA_SHARED_BUFFER=y
+CONFIG_DMA_VIRTUAL_CHANNELS=y
+CONFIG_DTC=y
+CONFIG_DT_IDLE_STATES=y
+CONFIG_DYNAMIC_DEBUG=y
+CONFIG_EDAC_ATOMIC_SCRUB=y
+CONFIG_EDAC_SUPPORT=y
+CONFIG_EEPROM_AT24=y
+# CONFIG_EEPROM_EE1004 is not set
+# CONFIG_ENERGY_MODEL is not set
+CONFIG_ESSEDMA=y
+# CONFIG_EXFAT_FS is not set
+CONFIG_EXTCON=y
+# CONFIG_FIELDBUS_DEV is not set
+CONFIG_FIXED_PHY=y
+CONFIG_FIX_EARLYCON_MEM=y
+# CONFIG_FSL_QDMA is not set
+# CONFIG_FS_VERITY is not set
+# CONFIG_FW_LOADER_COMPRESS is not set
+CONFIG_FW_LOADER_PAGED_BUF=y
+CONFIG_GENERIC_ALLOCATOR=y
+CONFIG_GENERIC_BUG=y
+CONFIG_GENERIC_CLOCKEVENTS=y
+CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y
+CONFIG_GENERIC_CPU_AUTOPROBE=y
+CONFIG_GENERIC_EARLY_IOREMAP=y
+CONFIG_GENERIC_IDLE_POLL_SETUP=y
+CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y
+CONFIG_GENERIC_IRQ_MULTI_HANDLER=y
+CONFIG_GENERIC_IRQ_SHOW=y
+CONFIG_GENERIC_IRQ_SHOW_LEVEL=y
+CONFIG_GENERIC_MSI_IRQ=y
+CONFIG_GENERIC_MSI_IRQ_DOMAIN=y
+CONFIG_GENERIC_PCI_IOMAP=y
+CONFIG_GENERIC_PHY=y
+CONFIG_GENERIC_PINCONF=y
+CONFIG_GENERIC_PINCTRL_GROUPS=y
+CONFIG_GENERIC_PINMUX_FUNCTIONS=y
+CONFIG_GENERIC_SCHED_CLOCK=y
+CONFIG_GENERIC_SMP_IDLE_THREAD=y
+CONFIG_GENERIC_STRNCPY_FROM_USER=y
+CONFIG_GENERIC_STRNLEN_USER=y
+CONFIG_GENERIC_TIME_VSYSCALL=y
+CONFIG_GPIOLIB=y
+CONFIG_GPIOLIB_IRQCHIP=y
+CONFIG_GPIO_74X164=y
+# CONFIG_GPIO_AMD_FCH is not set
+# CONFIG_GPIO_CADENCE is not set
+# CONFIG_GPIO_GW_PLD is not set
+# CONFIG_GPIO_SAMA5D2_PIOBU is not set
+CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_WATCHDOG=y
+# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set
+# CONFIG_GVE is not set
+# CONFIG_HABANA_AI is not set
+CONFIG_HANDLE_DOMAIN_IRQ=y
+CONFIG_HARDEN_BRANCH_PREDICTOR=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_HAS_DMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_IOPORT_MAP=y
+CONFIG_HAVE_ARCH_AUDITSYSCALL=y
+CONFIG_HAVE_ARCH_BITREVERSE=y
+CONFIG_HAVE_ARCH_JUMP_LABEL=y
+CONFIG_HAVE_ARCH_KGDB=y
+CONFIG_HAVE_ARCH_PFN_VALID=y
+CONFIG_HAVE_ARCH_SECCOMP_FILTER=y
+CONFIG_HAVE_ARCH_THREAD_STRUCT_WHITELIST=y
+CONFIG_HAVE_ARCH_TRACEHOOK=y
+CONFIG_HAVE_ARM_ARCH_TIMER=y
+CONFIG_HAVE_ARM_SMCCC=y
+CONFIG_HAVE_CLK=y
+CONFIG_HAVE_CLK_PREPARE=y
+CONFIG_HAVE_CONTEXT_TRACKING=y
+CONFIG_HAVE_C_RECORDMCOUNT=y
+CONFIG_HAVE_DEBUG_KMEMLEAK=y
+CONFIG_HAVE_DMA_CONTIGUOUS=y
+CONFIG_HAVE_DYNAMIC_FTRACE=y
+CONFIG_HAVE_DYNAMIC_FTRACE_WITH_REGS=y
+CONFIG_HAVE_EBPF_JIT=y
+CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
+CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y
+CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_HAVE_IDE=y
+CONFIG_HAVE_IRQ_TIME_ACCOUNTING=y
+CONFIG_HAVE_LD_DEAD_CODE_DATA_ELIMINATION=y
+CONFIG_HAVE_MOD_ARCH_SPECIFIC=y
+CONFIG_HAVE_NET_DSA=y
+CONFIG_HAVE_OPROFILE=y
+CONFIG_HAVE_OPTPROBES=y
+CONFIG_HAVE_PCI=y
+CONFIG_HAVE_PERF_EVENTS=y
+CONFIG_HAVE_PERF_REGS=y
+CONFIG_HAVE_PERF_USER_STACK_DUMP=y
+CONFIG_HAVE_PROC_CPU=y
+CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y
+CONFIG_HAVE_RSEQ=y
+CONFIG_HAVE_SMP=y
+CONFIG_HAVE_SYSCALL_TRACEPOINTS=y
+CONFIG_HAVE_UID16=y
+CONFIG_HAVE_VIRT_CPU_ACCOUNTING_GEN=y
+# CONFIG_HEADERS_INSTALL is not set
+# CONFIG_HEADER_TEST is not set
+CONFIG_HIGHMEM=y
+# CONFIG_HIGHPTE is not set
+CONFIG_HWSPINLOCK=y
+CONFIG_HWSPINLOCK_QCOM=y
+CONFIG_HW_RANDOM=y
+CONFIG_HW_RANDOM_OPTEE=y
+CONFIG_HZ_FIXED=0
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
+# CONFIG_I2C_NVIDIA_GPU is not set
+CONFIG_I2C_QUP=y
+# CONFIG_I3C is not set
+# CONFIG_IGC is not set
+# CONFIG_IKHEADERS is not set
+CONFIG_INITRAMFS_SOURCE=""
+# CONFIG_INIT_ON_ALLOC_DEFAULT_ON is not set
+# CONFIG_INIT_ON_FREE_DEFAULT_ON is not set
+CONFIG_INIT_STACK_NONE=y
+# CONFIG_INTERCONNECT is not set
+# CONFIG_IOMMU_DEBUGFS is not set
+# CONFIG_IOMMU_IO_PGTABLE_ARMV7S is not set
+# CONFIG_IOMMU_IO_PGTABLE_LPAE is not set
+CONFIG_IOMMU_SUPPORT=y
+CONFIG_IO_URING=y
+CONFIG_IPQ_GCC_4019=y
+# CONFIG_IPQ_GCC_806X is not set
+# CONFIG_IPQ_GCC_8074 is not set
+# CONFIG_IPQ_LCC_806X is not set
+CONFIG_IRQCHIP=y
+CONFIG_IRQ_DOMAIN=y
+CONFIG_IRQ_DOMAIN_HIERARCHY=y
+CONFIG_IRQ_FORCED_THREADING=y
+CONFIG_IRQ_WORK=y
+CONFIG_KASAN_STACK=1
+# CONFIG_KPSS_XCC is not set
+# CONFIG_KRAITCC is not set
+# CONFIG_LCD_CLASS_DEVICE is not set
+# CONFIG_LEDS_AN30259A is not set
+# CONFIG_LEDS_LM3532 is not set
+CONFIG_LEDS_LP5562=y
+CONFIG_LEDS_LP55XX_COMMON=y
+# CONFIG_LEDS_TRIGGER_AUDIO is not set
+# CONFIG_LEDS_TRIGGER_PATTERN is not set
+CONFIG_LIBFDT=y
+CONFIG_LOCK_DEBUGGING_SUPPORT=y
+# CONFIG_LOCK_EVENT_COUNTS is not set
+CONFIG_LOCK_SPIN_ON_OWNER=y
+CONFIG_LSM="lockdown,yama,loadpin,safesetid,integrity"
+CONFIG_LZO_COMPRESS=y
+CONFIG_LZO_DECOMPRESS=y
+CONFIG_MDIO_BITBANG=y
+CONFIG_MDIO_BUS=y
+# CONFIG_MDIO_BUS_MUX_MULTIPLEXER is not set
+CONFIG_MDIO_DEVICE=y
+CONFIG_MDIO_GPIO=y
+CONFIG_MDIO_IPQ40XX=y
+# CONFIG_MDM_GCC_9615 is not set
+# CONFIG_MDM_LCC_9615 is not set
+CONFIG_MEMFD_CREATE=y
+# CONFIG_MFD_LOCHNAGAR is not set
+# CONFIG_MFD_MAX77650 is not set
+# CONFIG_MFD_QCOM_RPM is not set
+# CONFIG_MFD_ROHM_BD70528 is not set
+# CONFIG_MFD_SPMI_PMIC is not set
+# CONFIG_MFD_STMFX is not set
+# CONFIG_MFD_STPMIC1 is not set
+CONFIG_MFD_SYSCON=y
+# CONFIG_MFD_TQMX86 is not set
+CONFIG_MIGHT_HAVE_CACHE_L2X0=y
+CONFIG_MIGRATION=y
+# CONFIG_MISC_ALCOR_PCI is not set
+CONFIG_MODULES_USE_ELF_REL=y
+# CONFIG_MODULE_ALLOW_MISSING_NAMESPACE_IMPORTS is not set
+# CONFIG_MSM_GCC_8660 is not set
+# CONFIG_MSM_GCC_8916 is not set
+# CONFIG_MSM_GCC_8960 is not set
+# CONFIG_MSM_GCC_8974 is not set
+# CONFIG_MSM_GCC_8994 is not set
+# CONFIG_MSM_GCC_8996 is not set
+# CONFIG_MSM_GCC_8998 is not set
+# CONFIG_MSM_LCC_8960 is not set
+# CONFIG_MSM_MMCC_8960 is not set
+# CONFIG_MSM_MMCC_8974 is not set
+# CONFIG_MSM_MMCC_8996 is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_HYPERBUS is not set
+CONFIG_MTD_NAND_CORE=y
+# CONFIG_MTD_RAW_NAND is not set
+CONFIG_MTD_SPI_NAND=y
+CONFIG_MTD_SPI_NOR=y
+CONFIG_MTD_SPLIT_FIRMWARE=y
+CONFIG_MTD_SPLIT_FIT_FW=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_BEB_LIMIT=20
+CONFIG_MTD_UBI_BLOCK=y
+# CONFIG_MTD_UBI_FASTMAP is not set
+# CONFIG_MTD_UBI_GLUEBI is not set
+CONFIG_MTD_UBI_WL_THRESHOLD=4096
+CONFIG_MUTEX_SPIN_ON_OWNER=y
+CONFIG_NEED_DMA_MAP_STATE=y
+CONFIG_NEON=y
+CONFIG_NET_DEVLINK=y
+CONFIG_NET_DSA=y
+# CONFIG_NET_DSA_LANTIQ_GSWIP is not set
+# CONFIG_NET_DSA_MICROCHIP_KSZ8795 is not set
+# CONFIG_NET_DSA_MICROCHIP_KSZ9477 is not set
+CONFIG_NET_DSA_QCA8K=y
+# CONFIG_NET_DSA_SJA1105 is not set
+# CONFIG_NET_DSA_TAG_8021Q is not set
+# CONFIG_NET_DSA_TAG_BRCM is not set
+# CONFIG_NET_DSA_TAG_BRCM_PREPEND is not set
+# CONFIG_NET_DSA_TAG_GSWIP is not set
+# CONFIG_NET_DSA_TAG_KSZ is not set
+# CONFIG_NET_DSA_TAG_LAN9303 is not set
+# CONFIG_NET_DSA_TAG_MTK is not set
+CONFIG_NET_DSA_TAG_QCA=y
+# CONFIG_NET_DSA_TAG_SJA1105 is not set
+# CONFIG_NET_DSA_TAG_TRAILER is not set
+# CONFIG_NET_DSA_VITESSE_VSC73XX_PLATFORM is not set
+# CONFIG_NET_DSA_VITESSE_VSC73XX_SPI is not set
+CONFIG_NET_FLOW_LIMIT=y
+CONFIG_NET_PTP_CLASSIFY=y
+# CONFIG_NET_SCH_TAPRIO is not set
+CONFIG_NET_SWITCHDEV=y
+CONFIG_NET_VENDOR_GOOGLE=y
+CONFIG_NET_VENDOR_PENSANDO=y
+# CONFIG_NI_XGE_MANAGEMENT_ENET is not set
+CONFIG_NLS=y
+CONFIG_NO_HZ=y
+CONFIG_NO_HZ_COMMON=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_NR_CPUS=4
+# CONFIG_NULL_TTY is not set
+CONFIG_NVMEM=y
+# CONFIG_NVMEM_REBOOT_MODE is not set
+CONFIG_NVMEM_SYSFS=y
+CONFIG_OF=y
+CONFIG_OF_ADDRESS=y
+CONFIG_OF_EARLY_FLATTREE=y
+CONFIG_OF_FLATTREE=y
+CONFIG_OF_GPIO=y
+CONFIG_OF_IRQ=y
+CONFIG_OF_KOBJ=y
+CONFIG_OF_MDIO=y
+CONFIG_OF_NET=y
+CONFIG_OF_RESERVED_MEM=y
+CONFIG_OLD_SIGACTION=y
+CONFIG_OLD_SIGSUSPEND3=y
+CONFIG_OPTEE=y
+CONFIG_OPTEE_SHM_NUM_PRIV_PAGES=1
+# CONFIG_PACKING is not set
+CONFIG_PADATA=y
+CONFIG_PAGE_OFFSET=0xC0000000
+CONFIG_PCI=y
+CONFIG_PCIEAER=y
+CONFIG_PCIEPORTBUS=y
+# CONFIG_PCIE_BW is not set
+CONFIG_PCIE_DW=y
+CONFIG_PCIE_DW_HOST=y
+CONFIG_PCIE_QCOM=y
+CONFIG_PCI_DISABLE_COMMON_QUIRKS=y
+CONFIG_PCI_DOMAINS=y
+CONFIG_PCI_DOMAINS_GENERIC=y
+# CONFIG_PCI_MESON is not set
+CONFIG_PCI_MSI=y
+CONFIG_PCI_MSI_IRQ_DOMAIN=y
+# CONFIG_PCI_V3_SEMI is not set
+CONFIG_PERF_USE_VMALLOC=y
+CONFIG_PGTABLE_LEVELS=2
+CONFIG_PHYLIB=y
+CONFIG_PHYLINK=y
+# CONFIG_PHY_CADENCE_DP is not set
+# CONFIG_PHY_CADENCE_DPHY is not set
+# CONFIG_PHY_CADENCE_SIERRA is not set
+# CONFIG_PHY_FSL_IMX8MQ_USB is not set
+# CONFIG_PHY_MIXEL_MIPI_DPHY is not set
+# CONFIG_PHY_OCELOT_SERDES is not set
+# CONFIG_PHY_QCOM_APQ8064_SATA is not set
+CONFIG_PHY_QCOM_IPQ4019_USB=y
+# CONFIG_PHY_QCOM_IPQ806X_SATA is not set
+# CONFIG_PHY_QCOM_PCIE2 is not set
+# CONFIG_PHY_QCOM_QMP is not set
+# CONFIG_PHY_QCOM_QUSB2 is not set
+# CONFIG_PHY_QCOM_UFS is not set
+CONFIG_PINCTRL=y
+# CONFIG_PINCTRL_APQ8064 is not set
+# CONFIG_PINCTRL_APQ8084 is not set
+CONFIG_PINCTRL_IPQ4019=y
+# CONFIG_PINCTRL_IPQ8064 is not set
+# CONFIG_PINCTRL_IPQ8074 is not set
+# CONFIG_PINCTRL_MDM9615 is not set
+CONFIG_PINCTRL_MSM=y
+# CONFIG_PINCTRL_MSM8660 is not set
+# CONFIG_PINCTRL_MSM8916 is not set
+# CONFIG_PINCTRL_MSM8960 is not set
+# CONFIG_PINCTRL_MSM8994 is not set
+# CONFIG_PINCTRL_MSM8996 is not set
+# CONFIG_PINCTRL_MSM8998 is not set
+# CONFIG_PINCTRL_OCELOT is not set
+# CONFIG_PINCTRL_QCOM_SPMI_PMIC is not set
+# CONFIG_PINCTRL_QCOM_SSBI_PMIC is not set
+# CONFIG_PINCTRL_QCS404 is not set
+# CONFIG_PINCTRL_SC7180 is not set
+# CONFIG_PINCTRL_SDM660 is not set
+# CONFIG_PINCTRL_SDM845 is not set
+# CONFIG_PINCTRL_SM8150 is not set
+# CONFIG_PINCTRL_STMFX is not set
+CONFIG_PM_OPP=y
+CONFIG_POWER_RESET=y
+CONFIG_POWER_RESET_MSM=y
+CONFIG_POWER_SUPPLY=y
+CONFIG_PPS=y
+# CONFIG_PRINTK_CALLER is not set
+CONFIG_PRINTK_TIME=y
+# CONFIG_PSI is not set
+CONFIG_PTP_1588_CLOCK=y
+# CONFIG_PVPANIC is not set
+CONFIG_QCOM_A53PLL=y
+CONFIG_QCOM_BAM_DMA=y
+# CONFIG_QCOM_COMMAND_DB is not set
+# CONFIG_QCOM_EBI2 is not set
+# CONFIG_QCOM_GENI_SE is not set
+# CONFIG_QCOM_GSBI is not set
+# CONFIG_QCOM_HFPLL is not set
+# CONFIG_QCOM_IOMMU is not set
+# CONFIG_QCOM_LLCC is not set
+# CONFIG_QCOM_PDC is not set
+CONFIG_QCOM_PM=y
+CONFIG_QCOM_QFPROM=y
+# CONFIG_QCOM_RMTFS_MEM is not set
+CONFIG_QCOM_SCM=y
+CONFIG_QCOM_SCM_32=y
+# CONFIG_QCOM_SCM_DOWNLOAD_MODE_DEFAULT is not set
+CONFIG_QCOM_SMEM=y
+# CONFIG_QCOM_SMSM is not set
+# CONFIG_QCOM_SOCINFO is not set
+CONFIG_QCOM_TCSR=y
+# CONFIG_QCOM_TSENS is not set
+CONFIG_QCOM_WDT=y
+# CONFIG_QCS_GCC_404 is not set
+# CONFIG_QCS_TURING_404 is not set
+# CONFIG_QRTR is not set
+# CONFIG_RANDOM_TRUST_BOOTLOADER is not set
+CONFIG_RAS=y
+CONFIG_RATIONAL=y
+CONFIG_RCU_CPU_STALL_TIMEOUT=21
+CONFIG_RCU_NEED_SEGCBLIST=y
+CONFIG_RCU_STALL_COMMON=y
+# CONFIG_REED_SOLOMON_TEST is not set
+CONFIG_REFCOUNT_FULL=y
+CONFIG_REGMAP=y
+CONFIG_REGMAP_I2C=y
+CONFIG_REGMAP_MMIO=y
+CONFIG_REGMAP_SPI=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_FIXED_VOLTAGE=y
+# CONFIG_REGULATOR_QCOM_SPMI is not set
+CONFIG_REGULATOR_VCTRL=y
+CONFIG_RESET_CONTROLLER=y
+# CONFIG_RESET_QCOM_AOSS is not set
+# CONFIG_RESET_QCOM_PDC is not set
+CONFIG_RFS_ACCEL=y
+CONFIG_RPS=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_I2C_AND_SPI=y
+CONFIG_RWSEM_SPIN_ON_OWNER=y
+# CONFIG_SDM_CAMCC_845 is not set
+# CONFIG_SDM_DISPCC_845 is not set
+# CONFIG_SDM_GCC_660 is not set
+# CONFIG_SDM_GCC_845 is not set
+# CONFIG_SDM_GPUCC_845 is not set
+# CONFIG_SDM_LPASSCC_845 is not set
+# CONFIG_SDM_VIDEOCC_845 is not set
+CONFIG_SERIAL_8250_FSL=y
+# CONFIG_SERIAL_AMBA_PL011 is not set
+# CONFIG_SERIAL_FSL_LINFLEXUART is not set
+CONFIG_SERIAL_MCTRL_GPIO=y
+CONFIG_SERIAL_MSM=y
+CONFIG_SERIAL_MSM_CONSOLE=y
+# CONFIG_SERIAL_SIFIVE is not set
+# CONFIG_SFP is not set
+CONFIG_SGL_ALLOC=y
+# CONFIG_SHUFFLE_PAGE_ALLOCATOR is not set
+CONFIG_SMP=y
+CONFIG_SMP_ON_UP=y
+# CONFIG_SM_GCC_8150 is not set
+CONFIG_SPARSE_IRQ=y
+CONFIG_SPI=y
+CONFIG_SPI_BITBANG=y
+CONFIG_SPI_GPIO=y
+CONFIG_SPI_MASTER=y
+CONFIG_SPI_MEM=y
+# CONFIG_SPI_MTK_QUADSPI is not set
+# CONFIG_SPI_QCOM_QSPI is not set
+CONFIG_SPI_QUP=y
+CONFIG_SPMI=y
+CONFIG_SPMI_MSM_PMIC_ARB=y
+# CONFIG_SPMI_PMIC_CLKDIV is not set
+CONFIG_SRCU=y
+CONFIG_SWCONFIG=y
+CONFIG_SWCONFIG_LEDS=y
+CONFIG_SWPHY=y
+CONFIG_SWP_EMULATE=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_TEE=y
+# CONFIG_TEST_BLACKHOLE_DEV is not set
+# CONFIG_TEST_MEMCAT_P is not set
+# CONFIG_TEST_MEMINIT is not set
+# CONFIG_TEST_STACKINIT is not set
+# CONFIG_TEST_STRSCPY is not set
+# CONFIG_TEST_VMALLOC is not set
+# CONFIG_TEST_XARRAY is not set
+CONFIG_THERMAL=y
+CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y
+CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0
+CONFIG_THERMAL_GOV_STEP_WISE=y
+CONFIG_THERMAL_OF=y
+# CONFIG_THUMB2_KERNEL is not set
+CONFIG_TICK_CPU_ACCOUNTING=y
+CONFIG_TIMER_OF=y
+CONFIG_TIMER_PROBE=y
+# CONFIG_TI_CPSW_PHY_SEL is not set
+CONFIG_TREE_RCU=y
+CONFIG_TREE_SRCU=y
+# CONFIG_TRUSTED_FOUNDATIONS is not set
+CONFIG_UBIFS_FS=y
+CONFIG_UBIFS_FS_ADVANCED_COMPR=y
+CONFIG_UBIFS_FS_LZO=y
+CONFIG_UBIFS_FS_ZLIB=y
+CONFIG_UBIFS_FS_ZSTD=y
+CONFIG_UBSAN_ALIGNMENT=y
+# CONFIG_UDMABUF is not set
+CONFIG_UEVENT_HELPER_PATH=""
+CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h"
+# CONFIG_UNICODE is not set
+CONFIG_UNIX_SCM=y
+CONFIG_UNWINDER_ARM=y
+# CONFIG_UNWINDER_FRAME_POINTER is not set
+CONFIG_USB=y
+CONFIG_USB_COMMON=y
+# CONFIG_USB_CONN_GPIO is not set
+# CONFIG_USB_EHCI_HCD is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USE_OF=y
+# CONFIG_VALIDATE_FS_PARSER is not set
+CONFIG_VDSO=y
+CONFIG_VFP=y
+CONFIG_VFPv3=y
+CONFIG_WATCHDOG_CORE=y
+CONFIG_WATCHDOG_OPEN_TIMEOUT=0
+# CONFIG_XILINX_SDFEC is not set
+CONFIG_XPS=y
+CONFIG_XXHASH=y
+CONFIG_XZ_DEC_ARM=y
+CONFIG_XZ_DEC_BCJ=y
+CONFIG_ZBOOT_ROM_BSS=0
+CONFIG_ZBOOT_ROM_TEXT=0
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZSTD_COMPRESS=y
+CONFIG_ZSTD_DECOMPRESS=y
--- /dev/null
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2017, Sven Eckelmann <sven.eckelmann@openmesh.com>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "OpenMesh A42";
+ compatible = "openmesh,a42";
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2: usb2@60f8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ aliases {
+ led-boot = &power;
+ led-failsafe = &power;
+ led-running = &power;
+ led-upgrade = &power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ red {
+ label = "a42:red:status";
+ gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-off";
+ };
+
+ power: green {
+ label = "a42:green:status";
+ gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ blue {
+ label = "a42:blue:status";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-off";
+ };
+ };
+
+ watchdog {
+ compatible = "linux,wdt-gpio";
+ gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+ hw_algo = "toggle";
+ /* hw_margin_ms is actually 300s but driver limits it to 60s */
+ hw_margin_ms = <60000>;
+ always-running;
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ /* partitions are passed via bootloader */
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <2 0x20>;
+};
+
+&gmac1 {
+ qcom,phy_mdio_addr = <3>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <1 0x10>;
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "OM-A42";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "OM-A42";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "ALFA Network AP120C-AC";
+ compatible = "alfa-network,ap120c-ac";
+
+ aliases {
+ led-boot = &status;
+ led-failsafe = &status;
+ led-running = &status;
+ led-upgrade = &status;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ status: status {
+ label = "ap120c-ac:blue:status";
+ gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+
+ wan {
+ label = "ap120c-ac:amber:wan";
+ gpios = <&qca8075 19 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan2g {
+ label = "ap120c-ac:green:wlan2g";
+ gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wlan5g {
+ label = "ap120c-ac:red:wlan5g";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy1tpt";
+ };
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ counter@4a1000 {
+ compatible = "qcom,qca-gcnt";
+ reg = <0x4a1000 0x4>;
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2@60f8800 {
+ status = "okay";
+ };
+
+ usb3@8af8800 {
+ status = "okay";
+
+ dwc3@8a00000 {
+ phys = <&usb3_hs_phy>;
+ phy-names = "usb2-phy";
+ };
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ qca8075: ess-switch@c000000 {
+ status = "okay";
+
+ switch_lan_bmp = <0x10>;
+ switch_wan_bmp = <0x20>;
+
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_i2c3 {
+ status = "okay";
+
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+
+ tpm@29 {
+ compatible = "atmel,at97sc3204t";
+ reg = <0x29>;
+ };
+};
+
+&blsp1_spi1 {
+ status = "okay";
+
+ pinctrl-0 = <&spi0_pins>;
+ pinctrl-names = "default";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>,
+ <&tlmm 4 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+
+ partition@d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+
+ partition@e0000 {
+ label = "APPSBLENV";
+ reg = <0x000e0000 0x00010000>;
+ };
+
+ partition@f0000 {
+ label = "APPSBL";
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+
+ partition@170000 {
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+
+ partition@180000 {
+ label = "priv_data1";
+ reg = <0x00180000 0x00010000>;
+ read-only;
+ };
+
+ partition@190000 {
+ label = "priv_data2";
+ reg = <0x00190000 0x00010000>;
+ read-only;
+ };
+ };
+ };
+
+ nand@1 {
+ compatible = "spi-nand";
+ reg = <1>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "rootfs1";
+ reg = <0x00000000 0x04000000>;
+ };
+
+ partition@4000000 {
+ label = "rootfs2";
+ reg = <0x04000000 0x04000000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ status = "okay";
+
+ pinctrl-0 = <&serial0_pins>;
+ pinctrl-names = "default";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,forced_duplex = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,phy_mdio_addr = <3>;
+ qcom,poll_required = <1>;
+ vlan_tag = <1 0x10>;
+};
+
+&gmac1 {
+ qcom,forced_duplex = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <1>;
+ vlan_tag = <2 0x20>;
+};
+
+&tlmm {
+ i2c0_pins: i2c0_pinmux {
+ mux_i2c {
+ function = "blsp_i2c0";
+ pins = "gpio58", "gpio59";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ mdio_pins: mdio_pinmux {
+ mux_mdio {
+ pins = "gpio53";
+ function = "mdio";
+ bias-pull-up;
+ };
+
+ mux_mdc {
+ pins = "gpio52";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ serial0_pins: serial0_pinmux {
+ mux_uart {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi0_pins: spi0_pinmux {
+ mux_spi {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ mux_cs {
+ function = "gpio";
+ pins = "gpio54", "gpio4";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "ALFA-Network-AP120C-AC";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "EZVIZ CS-W3-WD1200G EUP";
+ compatible = "ezviz,cs-w3-wd1200g-eup";
+
+ aliases {
+ led-boot = &led_status_green;
+ led-failsafe = &led_status_red;
+ led-running = &led_status_blue;
+ led-upgrade = &led_status_green;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <5000>;
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status_red: status_red {
+ label = "cs-w3-wd1200g-eup:red:status";
+ gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_green: status_green {
+ label = "cs-w3-wd1200g-eup:green:status";
+ gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
+ };
+
+ led_status_blue: status_blue {
+ label = "cs-w3-wd1200g-eup:blue:status";
+ gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio53";
+ function = "mdio";
+ bias-pull-up;
+ };
+
+ mux_2 {
+ pins = "gpio52";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0@0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+
+ partition1@40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+
+ partition2@60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+
+ partition3@c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+
+ partition4@d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+
+ partition5@E0000 {
+ label = "APPSBLENV";
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+
+ partition6@F0000 {
+ label = "APPSBL";
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+
+ partition7@170000 {
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+
+ partition9@580000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x00180000 0x00e80000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "ezviz-cs-w3-wd1200g-eup";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "ezviz-cs-w3-wd1200g-eup";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "D-Link DAP 2610";
+ compatible = "dlink,dap-2610";
+
+ aliases {
+ led-boot = &led_red;
+ led-failsafe = &led_red;
+ led-running = &led_green;
+ led-upgrade = &led_red;
+ };
+
+ soc {
+ edma@c080000 {
+ qcom,num_gmac = <1>;
+ status = "ok";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ rng@22000 {
+ status = "ok";
+ };
+
+ crypto@8e3a000 {
+ status = "ok";
+ };
+
+ watchdog@b017000 {
+ status = "ok";
+ };
+
+ ess-switch@c000000 {
+ status = "ok";
+ switch_lan_bmp = <0x20>;
+ switch_wan_bmp = <0x00>;
+ };
+
+ ess-psgmii@98000 {
+ status = "ok";
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_red: red {
+ label = "dap-2610:red:power";
+ gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
+ };
+
+ led_green: green {
+ label = "dap-2610:green:power";
+ gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "ok";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "fixed-partitions";
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+ partition@40000 {
+ label = "MIBIB";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+ partition@60000 {
+ label = "QSEE";
+ reg = <0x60000 0x60000>;
+ read-only;
+ };
+ partition@c0000 {
+ label = "CDT";
+ reg = <0xc0000 0x10000>;
+ read-only;
+ };
+ partition@d0000 {
+ label = "DDRPARAMS";
+ reg = <0xd0000 0x10000>;
+ read-only;
+ };
+ partition@e0000 {
+ label = "APPSBLENV";
+ reg = <0xe0000 0x10000>;
+ read-only;
+ };
+ partition@f0000 {
+ label = "APPSBL";
+ reg = <0xf0000 0x80000>;
+ read-only;
+ };
+ partition@170000 {
+ label = "ART";
+ reg = <0x170000 0x10000>;
+ read-only;
+ };
+ partition@180000 {
+ compatible = "wrg";
+ label = "firmware";
+ reg = <0x180000 0xdc0000>;
+ };
+ partition@fb0000 {
+ label = "rgbd";
+ reg = <0xfb0000 0x10000>;
+ read-only;
+ };
+ partition@fc0000 {
+ label = "bdcfg";
+ reg = <0xfc0000 0x10000>;
+ read-only;
+ };
+ partition@fd0000 {
+ label = "langpack";
+ reg = <0xfd0000 0x20000>;
+ read-only;
+ };
+ partition@ff0000 {
+ label = "certificate";
+ reg = <0xff0000 0x10000>;
+ read-only;
+ };
+ partition@f40000 {
+ label = "captival";
+ reg = <0xf40000 0x70000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&blsp_dma {
+ status = "ok";
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "ok";
+};
+
+&cryptobam {
+ status = "ok";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <1 0x20>;
+};
+
+&mdio {
+ status = "ok";
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ mux {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ mux_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&wifi0 {
+ status = "ok";
+ qcom,ath10k-calibration-variant = "dlink,dap-2610";
+};
+
+&wifi1 {
+ status = "ok";
+ qcom,ath10k-calibration-variant = "dlink,dap-2610";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Linksys EA6350v3";
+ compatible = "linksys,ea6350v3";
+
+ aliases {
+ led-boot = &power;
+ led-failsafe = &power;
+ led-running = &power;
+ led-upgrade = &power;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2@60f8800 {
+ status = "okay";
+ };
+
+ usb3@8af8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power: status {
+ label = "EA6350v3:green:status";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "linksys-ea6350v3";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "linksys-ea6350v3";
+};
+
+
+&blsp_dma {
+ status = "okay";
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ mux {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ mux_cs {
+ function = "gpio";
+ pins = "gpio54", "gpio59";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp1_spi1 { /* BLSP1 QUP1 */
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>,
+ <&tlmm 59 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ SBL1@0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ MBIB@40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ QSEE@60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+ CDT@c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+ APPSBLENV@d0000 {
+ label = "APPSBLENV";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+ APPSBL@e0000 {
+ label = "APPSBL"; /* uboot */
+ reg = <0x000e0000 0x00080000>;
+ read-only;
+ };
+ ART@160000 {
+ label = "ART";
+ reg = <0x00160000 0x00010000>;
+ read-only;
+ };
+ u_env@170000 {
+ label = "u_env";
+ reg = <0x00170000 0x00020000>;
+ };
+ s_env@190000 {
+ label = "s_env";
+ reg = <0x00190000 0x00020000>;
+ };
+ devinfo@1b0000 {
+ label = "devinfo";
+ reg = <0x001b0000 0x00010000>;
+ };
+ /* 0x001c0000 - 0x00200000 unused */
+ };
+ };
+
+ flash@1 {
+ status = "okay";
+ compatible = "spi-nand";
+ reg = <1>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ kernel@0 {
+ label = "kernel";
+ reg = <0x00000000 0x02800000>;
+ };
+ rootfs@300000 {
+ label = "rootfs";
+ reg = <0x00300000 0x02500000>;
+ };
+ alt_kernel@2800000 {
+ label = "alt_kernel";
+ reg = <0x02800000 0x02800000>;
+ };
+ alt_rootfs@2b00000 {
+ label = "alt_rootfs";
+ reg = <0x02b00000 0x02500000>;
+ };
+ sysdiag@5000000 {
+ label = "sysdiag";
+ reg = <0x05000000 0x00100000>;
+ };
+ syscfg@5100000 {
+ label = "syscfg";
+ reg = <0x05100000 0x02F00000>;
+ };
+ /* 0x00000000 - 0x08000000: 128 MiB */
+ };
+ };
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "EnGenius EAP1300";
+ compatible = "engenius,eap1300";
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ aliases {
+ led-boot = &power;
+ led-failsafe = &power;
+ led-running = &power;
+ led-upgrade = &power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power: orange {
+ label = "eap1300:orange:power";
+ gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+ };
+
+ lan {
+ label = "eap1300:blue:lan";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ mesh {
+ label = "eap1300:blue:mesh";
+ gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan2g {
+ label = "eap1300:blue:wlan2g";
+ gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan5g {
+ label = "eap1300:yellow:wlan5g";
+ gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio54", "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ m25p80@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "0:SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ partition1@40000 {
+ label = "0:MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ partition2@60000 {
+ label = "0:QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+ partition3@c0000 {
+ label = "0:CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+ partition4@d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+ partition5@e0000 {
+ label = "0:APPSBLENV";
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+ partition6@f0000 {
+ label = "0:APPSBL";
+ reg = <0x000f0000 0x00090000>;
+ read-only;
+ };
+ partition7@180000 {
+ label = "0:ART";
+ reg = <0x00180000 0x00010000>;
+ read-only;
+ };
+ partition8@190000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x190000 0x1dc0000>;
+ };
+ partition9@1f50000 {
+ label = "u-boot-env";
+ reg = <0x01f50000 0x00010000>;
+ };
+ partition10@1f60000 {
+ label = "userconfig";
+ reg = <0x01f60000 0x000a0000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ vlan_tag = <2 0x20>;
+};
+
+&gmac1 {
+ vlan_tag = <1 0x10>;
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "EnGenius-EAP1300";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "EnGenius-EAP1300";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "EnGenius EMD1";
+ compatible = "engenius,emd1";
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ switch_lan_bmp = <0x20>;
+ switch_wan_bmp = <0x00>;
+ };
+
+ edma@c080000 {
+ status = "okay";
+ qcom,num_gmac = <1>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: power {
+ label = "emd1:white:power";
+ gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan2g {
+ label = "emd1:red:wlan2g";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wlan5g {
+ label = "emd1:blue:wlan5g";
+ gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ mesh {
+ label = "emd1:orange:mesh";
+ gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio54", "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0@0 {
+ label = "0:SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ partition1@40000 {
+ label = "0:MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ partition2@60000 {
+ label = "0:QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+ partition3@c0000 {
+ label = "0:CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+ partition4@d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+ partition5@e0000 {
+ label = "0:APPSBLENV";
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+ partition6@f0000 {
+ label = "0:APPSBL";
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+ partition7@170000 {
+ label = "0:ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+ partition8@180000 {
+ label = "userconfig";
+ reg = <0x00180000 0x00080000>;
+ read-only;
+ };
+ partition9@200000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x200000 0x01e00000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <1 0x20>;
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "EnGenius-EMD1";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "EnGenius-EMD1";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "EnGenius ENS620EXT";
+ compatible = "engenius,ens620ext";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ aliases {
+ led-boot = &power;
+ led-failsafe = &power;
+ led-running = &power;
+ led-upgrade = &power;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+
+ /*
+ * Disable the broken restart as a workaround for the buggy
+ * 3.0.0/3.0.1 U-boots that ship with the device.
+ * Note: The watchdog is now used to restart this device.
+ */
+ restart@4ab000 {
+ status = "disabled";
+ };
+ };
+
+ buttons {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power: power {
+ label = "ens620ext:amber:power";
+ gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+ };
+
+ lan1 {
+ label = "ens620ext:green:lan1";
+ gpios = <&tlmm 1 GPIO_ACTIVE_LOW>;
+ };
+
+ lan2 {
+ label = "ens620ext:green:lan2";
+ gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan2G {
+ label = "ens620ext:green:wlan2G";
+ gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan5G {
+ label = "ens620ext:green:wlan5G";
+ gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ mux {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ mux_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp1_spi1 { /* BLSP1 QUP1 */
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ partition@40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ partition@60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+ partition@c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+ partition@d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+ partition@e0000 {
+ label = "APPSBLENV"; /* uboot env*/
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+ partition@f0000 {
+ label = "APPSBL"; /* uboot */
+ reg = <0x000f0000 0x00090000>;
+ read-only;
+ };
+ partition@180000 {
+ label = "ART";
+ reg = <0x00180000 0x00010000>;
+ read-only;
+ };
+ partition@190000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x00190000 0x14d0000>;
+ };
+ partition@1660000 {
+ label = "failsafe";
+ reg = <0x01660000 0x008F0000>;
+ read-only;
+ };
+ partition@1f50000 {
+ label = "u-boot-env";
+ reg = <0x01f50000 0x00010000>;
+ read-only;
+ };
+ partition@1f60000 {
+ label = "userconfig";
+ reg = <0x01f60000 0x000a0000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "EnGenius-ENS620EXT";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "EnGenius-ENS620EXT";
+};
--- /dev/null
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, David Bauer <mail@david-bauer.net>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4018-ex61x0v2.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Netgear EX6100v2";
+ compatible = "netgear,ex6100v2";
+};
+
+&wifi0 {
+ qcom,ath10k-calibration-variant = "Netgear-EX6100v2";
+};
+
+&wifi1 {
+ qcom,ath10k-calibration-variant = "Netgear-EX6100v2";
+};
--- /dev/null
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, David Bauer <mail@david-bauer.net>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4018-ex61x0v2.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Netgear EX6150v2";
+ compatible = "netgear,ex6150v2";
+};
+
+&wifi0 {
+ qcom,ath10k-calibration-variant = "Netgear-EX6150v2";
+};
+
+&wifi1 {
+ qcom,ath10k-calibration-variant = "Netgear-EX6150v2";
+};
--- /dev/null
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, David Bauer <mail@david-bauer.net>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Netgear EX61X0v2";
+ compatible = "netgear,ex61x0v2";
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ qcom,num_gmac = <1>;
+ };
+ };
+
+ aliases {
+ led-boot = &power_amber;
+ led-failsafe = &power_amber;
+ led-running = &power_green;
+ led-upgrade = &power_amber;
+ label-mac-device = &gmac0;
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ led_spi {
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sck-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+ mosi-gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+ num-chipselects = <0>;
+
+ led_gpio: led_gpio@0 {
+ compatible = "fairchild,74hc595";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ registers-number = <1>;
+ spi-max-frequency = <1000000>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power_amber: power_amber {
+ label = "ex61x0v2:amber:power";
+ gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>;
+ };
+
+ power_green: power_green {
+ label = "ex61x0v2:green:power";
+ gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>;
+ };
+
+ right {
+ label = "ex61x0v2:blue:right";
+ gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>;
+ };
+
+ left {
+ label = "ex61x0v2:blue:left";
+ gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>;
+ };
+
+ client_green {
+ label = "ex61x0v2:green:client";
+ gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>;
+ };
+
+ client_red {
+ label = "ex61x0v2:red:client";
+ gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>;
+ };
+
+ router_green {
+ label = "ex61x0v2:green:router";
+ gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>;
+ };
+
+ router_red {
+ label = "ex61x0v2:red:router";
+ gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "ex61x0v2:green:wps";
+ gpios = <&tlmm 1 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ mx25l12805d@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0@0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+
+ partition1@40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+
+ partition2@60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+
+ partition3@c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+
+ partition4@d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+
+ partition5@E0000 {
+ label = "APPSBLENV";
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+
+ partition6@F0000 {
+ label = "APPSBL";
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+
+ partition7@170000 {
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+
+ partition8@180000 {
+ label = "config";
+ reg = <0x00180000 0x00010000>;
+ read-only;
+ };
+
+ partition9@190000 {
+ label = "pot";
+ reg = <0x00190000 0x00010000>;
+ read-only;
+ };
+
+ partition10@1a0000 {
+ label = "dnidata";
+ reg = <0x001a0000 0x00010000>;
+ read-only;
+ };
+
+ partition11@1b0000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x001b0000 0x00e10000>;
+ };
+
+ partition12@fc0000 {
+ label = "language";
+ reg = <0x00fc0000 0x00040000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+};
+
+&wifi1 {
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "AVM FRITZ!Box 4040";
+ compatible = "avm,fritzbox-4040";
+
+ aliases {
+ led-boot = &power;
+ led-failsafe = &flash;
+ led-running = &power;
+ led-upgrade = &flash;
+ label-mac-device = &gmac0;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2@60f8800 {
+ status = "okay";
+ };
+
+ usb3@8af8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ qca8075: ess-switch@c000000 {
+ status = "okay";
+
+ #gpio-cells = <2>;
+ gpio-controller;
+
+ enable-usb-power {
+ gpio-hog;
+ line-name = "enable USB3 power";
+ gpios = <7 GPIO_ACTIVE_HIGH>;
+ output-high;
+ };
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wlan {
+ label = "wlan";
+ gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ switch-leds {
+ compatible = "gpio-leds";
+
+ wlan {
+ label = "fritz4040:green:wlan";
+ gpios = <&qca8075 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ panic: info_red {
+ label = "fritz4040:red:info";
+ gpios = <&qca8075 3 GPIO_ACTIVE_HIGH>;
+ panic-indicator;
+ };
+
+ wan {
+ label = "fritz4040:green:wan";
+ gpios = <&qca8075 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ power: power {
+ label = "fritz4040:green:power";
+ gpios = <&qca8075 11 GPIO_ACTIVE_HIGH>;
+ };
+
+ lan {
+ label = "fritz4040:green:lan";
+ gpios = <&qca8075 13 GPIO_ACTIVE_HIGH>;
+ };
+
+ flash: info_amber {
+ label = "fritz4040:amber:info";
+ gpios = <&qca8075 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ mux {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ mux_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 { /* BLSP1 QUP1 */
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ status = "okay";
+ m25p,fast-read;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0@0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ partition1@40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ partition2@60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+ partition3@c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+ partition4@d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+ partition5@e0000 {
+ label = "APPSBLENV"; /* uboot env - empty */
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+ partition6@f0000 {
+ label = "urlader"; /* APPSBL */
+ reg = <0x000f0000 0x0002dc000>;
+ read-only;
+ };
+ partition7@11dc00 {
+ /* make a backup of this partition! */
+ label = "urlader_config";
+ reg = <0x0011dc00 0x00002400>;
+ read-only;
+ };
+ partition8@120000 {
+ label = "tffs1";
+ reg = <0x00120000 0x00080000>;
+ read-only;
+ };
+ partition9@1a0000 {
+ label = "tffs2";
+ reg = <0x001a0000 0x00080000>;
+ read-only;
+ };
+ partition10@220000 {
+ label = "uboot";
+ reg = <0x00220000 0x00080000>;
+ read-only;
+ };
+ partition11@2A0000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x002a0000 0x01c60000>;
+ };
+ partition12@1f00000 {
+ label = "jffs2";
+ reg = <0x01f00000 0x00100000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "AVM-FRITZBox-4040";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "AVM-FRITZBox-4040";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (c) 2018, Robert Marko <robimarko@gmail.com>
+
+#include "qcom-ipq4018-jalapeno.dtsi"
+
+/ {
+ model = "8devices Jalapeno";
+ compatible = "8dev,jalapeno";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+// Copyright (c) 2018, Robert Marko <robimarko@gmail.com>
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ counter@4a1000 {
+ compatible = "qcom,qca-gcnt";
+ reg = <0x4a1000 0x4>;
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ status = "okay";
+
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2: usb2@60f8800 {
+ status = "okay";
+ };
+
+ usb3: usb3@8af8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+
+ switch_lan_bmp = <0x10>; /* lan port bitmap */
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+};
+
+&tlmm {
+ mdio_pins: mdio_pinmux {
+ pinmux_1 {
+ pins = "gpio53";
+ function = "mdio";
+ };
+
+ pinmux_2 {
+ pins = "gpio52";
+ function = "mdc";
+ };
+
+ pinconf {
+ pins = "gpio52", "gpio53";
+ bias-pull-up;
+ };
+ };
+
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54", "gpio59";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ status = "okay";
+
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 59 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ status = "okay";
+
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+
+ partition@d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+
+ partition@e0000 {
+ label = "APPSBLENV"; /* uboot env*/
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+
+ partition@f0000 {
+ label = "APPSBL"; /* uboot */
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+
+ partition@170000 {
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+ };
+ };
+
+ spi-nand@1 {
+ status = "okay";
+
+ compatible = "spi-nand";
+ reg = <1>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "ubi";
+ reg = <0x00000000 0x08000000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ status = "okay";
+
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,poll_required = <1>;
+ qcom,poll_required_dynamic = <1>;
+ qcom,phy_mdio_addr = <3>;
+ vlan_tag = <1 0x10>;
+};
+
+&gmac1 {
+ qcom,poll_required = <1>;
+ qcom,poll_required_dynamic = <1>;
+ qcom,phy_mdio_addr = <4>;
+ vlan_tag = <2 0x20>;
+};
+
+&wifi0 {
+ status = "okay";
+
+ qcom,ath10k-calibration-variant = "8devices-Jalapeno";
+};
+
+&wifi1 {
+ status = "okay";
+
+ qcom,ath10k-calibration-variant = "8devices-Jalapeno";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2019, CRISIS INNOVATION LAB d.o.o.
+ * Author: Robert Marko <robert@meshpoint.me>
+ */
+
+#include "qcom-ipq4018-jalapeno.dtsi"
+
+/ {
+ model = "Crisis Innovation Lab MeshPoint.One";
+ compatible = "cilab,meshpoint-one";
+
+ aliases {
+ led-boot = &led_status;
+ led-failsafe = &led_status;
+ led-running = &led_status;
+ led-upgrade = &led_status;
+ };
+
+ soc {
+ i2c-gpio {
+ status = "okay";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ compatible = "i2c-gpio";
+ gpios = <&tlmm 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN) /* sda */
+ &tlmm 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN) /* scl */
+ >;
+
+ bme280@76 {
+ status = "okay";
+
+ compatible = "bosch,bme280";
+ reg = <0x76>;
+ };
+
+ pcf2129@51 {
+ status = "okay";
+
+ compatible = "nxp,pcf2129";
+ reg = <0x51>;
+ };
+
+ ina230@40 {
+ status = "okay";
+
+ compatible = "ti,ina230";
+ reg = <0x40>;
+ shunt-resistor = <2000>;
+ };
+
+ ina230@44 {
+ status = "okay";
+
+ compatible = "ti,ina230";
+ reg = <0x44>;
+ shunt-resistor = <2000>;
+ };
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART >;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_status: status {
+ label = "meshpoint-one:blue:status";
+ gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "ZyXEL NBG6617";
+ compatible = "zyxel,nbg6617";
+
+ chosen {
+ /*
+ * the vendor u-boot adds root and mtdparts cmdline parameters
+ * which we don't want... but we have to overwrite them or else
+ * the kernel will take them at face value.
+ */
+ bootargs-append = " mtdparts= root=31:13";
+ };
+
+ aliases {
+ led-boot = &power;
+ led-failsafe = &power;
+ led-running = &power;
+ led-upgrade = &power;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2@60f8800 {
+ status = "okay";
+
+ dwc3@6000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb2_port1: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+ };
+ };
+
+ usb3@8af8800 {
+ status = "okay";
+
+ dwc3@8a00000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb3_port1: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+
+ usb3_port2: port@2 {
+ reg = <2>;
+ #trigger-source-cells = <0>;
+ };
+ };
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wlan {
+ label = "wlan";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ linux,code = <KEY_RFKILL>;
+ linux,input-type = <EV_SW>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ power: power {
+ label = "nbg6617:green:power";
+ gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ usb {
+ label = "nbg6617:green:usb";
+ gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ trigger-sources = <&usb2_port1>, <&usb3_port1>, <&usb3_port2>;
+ linux,default-trigger = "usbport";
+ };
+
+ wlan2G {
+ label = "nbg6617:green:wlan2G";
+ gpios = <&tlmm 58 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan5G {
+ label = "nbg6617:green:wlan5G";
+ gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ wps {
+ label = "nbg6617:green:wps";
+ gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+ spi_0_pins: spi_0_pinmux {
+ mux {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ mux_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+ };
+ led_pins: led_pinmux {
+ mux {
+ pins = "gpio0", "gpio1", "gpio3", "gpio5", "gpio58";
+ drive-strength = <0x8>;
+ bias-disable;
+ output-low;
+ };
+ };
+};
+
+&blsp1_spi1 { /* BLSP1 QUP1 */
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ mx25l25635f@0 {
+ compatible = "mx25l25635f", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ status = "okay";
+ m25p,fast-read;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0@0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ partition1@40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ partition2@60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+ partition3@c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+ partition4@d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+ partition5@e0000 {
+ label = "APPSBL"; /* u-boot */
+ reg = <0x000e0000 0x00080000>;
+ /* U-Boot Standalone App "zloader" is located at 0x64000 */
+ read-only;
+ };
+ partition6@160000 {
+ label = "APPSBLENV"; /* u-boot env */
+ reg = <0x00160000 0x00010000>;
+ };
+ partition7@170000 {
+ /* make a backup of this partition! */
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+ partition8@180000 {
+ label = "kernel";
+ reg = <0x00180000 0x00400000>;
+ };
+ partition9@580000 {
+ label = "dualflag";
+ reg = <0x00580000 0x00010000>;
+ read-only;
+ };
+ partition10@590000 {
+ label = "header";
+ reg = <0x00590000 0x00010000>;
+ };
+ partition11@5a0000 {
+ label = "romd";
+ reg = <0x005a0000 0x00100000>;
+ read-only;
+ };
+ partition12@6a0000 {
+ label = "not_root_data";
+ /*
+ * for some strange reason, someone at ZyXEL
+ * had the "great" idea to put the rootfs_data
+ * in front of rootfs... Don't do that!
+ * As a result this one, full MebiByte remains
+ * unused.
+ */
+ reg = <0x006a0000 0x00100000>;
+ };
+ partition13@7a0000 {
+ label = "rootfs";
+ reg = <0x007a0000 0x01860000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "ZyXEL-NBG6617";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "ZyXEL-NBG6617";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "ASUS RT-AC58U";
+ compatible = "asus,rt-ac58u";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x8000000>;
+ };
+
+ aliases {
+ led-boot = &led_power;
+ led-failsafe = &led_power;
+ led-running = &led_power;
+ led-upgrade = &led_power;
+ };
+
+ chosen {
+ bootargs-append = " ubi.mtd=UBI_DEV";
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb3@8af8800 {
+ status = "okay";
+
+ dwc3@8a00000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb3_port1: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+
+ usb3_port2: port@2 {
+ reg = <2>;
+ #trigger-source-cells = <0>;
+ };
+ };
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_power: status {
+ label = "rt-ac58u:blue:status";
+ gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ wan {
+ label = "rt-ac58u:blue:wan";
+ gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan2G {
+ label = "rt-ac58u:blue:wlan2G";
+ gpios = <&tlmm 58 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wlan5G {
+ label = "rt-ac58u:blue:wlan5G";
+ gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ usb {
+ label = "rt-ac58u:blue:usb";
+ gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+ trigger-sources = <&usb3_port1>, <&usb3_port2>;
+ linux,default-trigger = "usbport";
+ };
+
+ lan {
+ label = "rt-ac58u:blue:lan";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ mux {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ mux_cs {
+ function = "gpio";
+ pins = "gpio54", "gpio59";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp1_spi1 { /* BLSP1 QUP1 */
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>,
+ <&tlmm 59 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ /*
+ * U-boot looks for "n25q128a11" node,
+ * if we don't have it, it will spit out the following warning:
+ * "ipq: fdt fixup unable to find compatible node".
+ */
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ linux,modalias = "m25p80", "mx25l1606e", "n25q128a11";
+ spi-max-frequency = <30000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ partition@40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ partition@60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+ partition@c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+ partition@d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+ partition@e0000 {
+ label = "APPSBLENV"; /* uboot env*/
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+ partition@f0000 {
+ label = "APPSBL"; /* uboot */
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+ partition@170000 {
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+ /* 0x00180000 - 0x00200000 unused */
+ };
+ };
+
+ spi-nand@1 {
+ compatible = "spi-nand";
+ reg = <1>;
+ spi-max-frequency = <30000000>;
+
+ /*
+ * U-boot looks for "spinand,mt29f" node,
+ * if we don't have it, it will spit out the following warning:
+ * "ipq: fdt fixup unable to find compatible node".
+ */
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ /*
+ * TODO: change to label = "ubi" once we drop 4.14.
+ * also drop the bootargs-append and all the
+ * userspace CI_UBIPART="UBI_DEV" remains.
+ */
+ label = "UBI_DEV";
+ reg = <0x00000000 0x08000000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "RT-AC58U";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "RT-AC58U";
+};
--- /dev/null
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2018, David Bauer <mail@david-bauer.net>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "ZyXEL WRE6606";
+ compatible = "zyxel,wre6606";
+
+ aliases {
+ led-boot = &power;
+ led-failsafe = &power;
+ led-running = &power;
+ led-upgrade = &power;
+ };
+
+ chosen {
+ bootargs-append = " mtdparts=";
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ qcom,num_gmac = <1>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wps {
+ label = "wre6606:green:wps";
+ gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan5g_green {
+ label = "wre6606:green:wlan5g";
+ gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ power: power {
+ label = "wre6606:green:power";
+ gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan5g_red {
+ label = "wre6606:red:wlan5g";
+ gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan2g_red {
+ label = "wre6606:red:wlan2g";
+ gpios = <&tlmm 58 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan2g_green {
+ label = "wre6606:green:wlan2g";
+ gpios = <&tlmm 59 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ mx25l12805d@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0@0 {
+ label = "SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+
+ partition1@40000 {
+ label = "MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+
+ partition2@60000 {
+ label = "QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+
+ partition3@c0000 {
+ label = "CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+
+ partition4@d0000 {
+ label = "DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+
+ partition5@E0000 {
+ label = "APPSBLENV";
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+
+ partition6@F0000 {
+ label = "APPSBL";
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+
+ partition7@170000 {
+ label = "ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+
+ partition8@180000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x00180000 0x00ce0000>;
+ };
+
+ partition9@e60000 {
+ label = "manufacture";
+ reg = <0x00e60000 0x00050000>;
+ read-only;
+ };
+
+ partition10@eb0000 {
+ label = "storage";
+ reg = <0x00eb0000 0x00150000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "ZyXEL-WRE6606";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "ZyXEL-WRE6606";
+};
--- /dev/null
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2017-2018, Sven Eckelmann <sven.eckelmann@openmesh.com>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "OpenMesh A62";
+ compatible = "openmesh,a62";
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2: usb2@60f8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ switch_lan_bmp = <0x10>;
+ switch_wan_bmp = <0x20>;
+
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART >;
+ };
+ };
+
+ aliases {
+ led-boot = &power;
+ led-failsafe = &power;
+ led-running = &power;
+ led-upgrade = &power;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ red {
+ label = "a62:red:status";
+ gpios = <&tlmm 43 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-off";
+ };
+
+ power: green {
+ label = "a62:green:status";
+ gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+ };
+
+ blue {
+ label = "a62:blue:status";
+ gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-off";
+ };
+ };
+
+ watchdog {
+ compatible = "linux,wdt-gpio";
+ gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
+ hw_algo = "toggle";
+ /* hw_margin_ms is actually 300s but driver limits it to 60s */
+ hw_margin_ms = <60000>;
+ always-running;
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ enable-usb-power {
+ gpio-hog;
+ gpios = <58 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "enable USB2 power";
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+ m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+ /* partitions are passed via bootloader */
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <3>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <1 0x10>;
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi2: wifi@1,0 {
+ compatible = "qcom,ath10k";
+ status = "okay";
+ reg = <0x00010000 0 0 0 0>;
+ qcom,ath10k-calibration-variant = "OM-A62";
+ ieee80211-freq-limit = <5170000 5350000>;
+ };
+ };
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "OM-A62";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "OM-A62";
+ ieee80211-freq-limit = <5470000 5875000>;
+};
--- /dev/null
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019-ap.dk04.1.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. IPQ40xx/AP-DK04.1-C1";
+};
--- /dev/null
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK04.1";
+ compatible = "qcom,ipq4019";
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ pinctrl@1000000 {
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ serial_1_pins: serial1_pinmux {
+ mux {
+ pins = "gpio8", "gpio9";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pinmux {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ };
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio12";
+ };
+ pinconf {
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pinconf_cs {
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ i2c_0_pins: i2c_0_pinmux {
+ pinmux {
+ function = "blsp_i2c0";
+ pins = "gpio10", "gpio11";
+ };
+ pinconf {
+ pins = "gpio10", "gpio11";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+
+ pullups {
+ pins = "gpio52", "gpio53", "gpio58",
+ "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+ };
+
+ blsp_dma: dma@7884000 {
+ status = "okay";
+ };
+
+ spi0: spi@78b5000 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+ mx25l25635e@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0>;
+ compatible = "mx25l25635e";
+ spi-max-frequency = <24000000>;
+ };
+ };
+
+ i2c0: i2c@78b7000 { /* BLSP1 QUP2 */
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+ };
+
+ serial@78af000 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ serial@78b0000 {
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ usb3_ss_phy: ssphy@9a000 {
+ status = "okay";
+ };
+
+ usb3_hs_phy: hsphy@a6000 {
+ status = "okay";
+ };
+
+ usb3: usb3@8af8800 {
+ status = "okay";
+ };
+
+ usb2_hs_phy: hsphy@a8000 {
+ status = "okay";
+ };
+
+ usb2: usb2@60f8800 {
+ status = "okay";
+ };
+
+ cryptobam: dma@8e04000 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ qpic_bam: dma@7984000 {
+ status = "okay";
+ };
+
+ nand: qpic-nand@79b0000 {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+ };
+};
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+ *
+ * Copyright (c) 2018 Peng Zhang <sd20@qxwlan.com>
+ *
+ */
+
+#include "qcom-ipq4019-e2600ac.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Qxwlan E2600AC c1";
+ compatible = "qxwlan,e2600ac-c1";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
+
+ flash@0 {
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "0:SBL1";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+ partition@40000 {
+ label = "0:MIBIB";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+ partition@60000 {
+ label = "0:QSEE";
+ reg = <0x60000 0x60000>;
+ read-only;
+ };
+ partition@c0000 {
+ label = "0:CDT";
+ reg = <0xc0000 0x10000>;
+ read-only;
+ };
+ partition@d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0xd0000 0x10000>;
+ read-only;
+ };
+ partition@e0000 {
+ label = "0:APPSBLENV";
+ reg = <0xe0000 0x10000>;
+ read-only;
+ };
+ partition@f0000 {
+ label = "0:APPSBL";
+ reg = <0xf0000 0x80000>;
+ read-only;
+ };
+ partition@170000 {
+ label = "0:ART";
+ reg = <0x170000 0x10000>;
+ read-only;
+ };
+ partition@180000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x180000 0x1e80000>;
+ };
+ };
+ };
+};
+
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+ *
+ * Copyright (c) 2018 Peng Zhang <sd20@qxwlan.com>
+ *
+ */
+
+#include "qcom-ipq4019-e2600ac.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Qxwlan E2600AC c2";
+ compatible = "qxwlan,e2600ac-c2";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
+
+ flash@0 {
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "0:SBL1";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+ partition@40000 {
+ label = "0:MIBIB";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+ partition@60000 {
+ label = "0:QSEE";
+ reg = <0x60000 0x60000>;
+ read-only;
+ };
+ partition@c0000 {
+ label = "0:CDT";
+ reg = <0xc0000 0x10000>;
+ read-only;
+ };
+ partition@d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0xd0000 0x10000>;
+ read-only;
+ };
+ partition@e0000 {
+ label = "0:APPSBLENV";
+ reg = <0xe0000 0x10000>;
+ read-only;
+ };
+ partition@f0000 {
+ label = "0:APPSBL";
+ reg = <0xf0000 0x80000>;
+ read-only;
+ };
+ partition@170000 {
+ label = "0:ART";
+ reg = <0x170000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "ubi";
+ reg = <0x00000000 0x04000000>;
+ };
+ };
+ };
+};
+
+&tlmm {
+ nand_pins: nand-pins {
+
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+};
+
--- /dev/null
+/* SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+ *
+ * Copyright (c) 2018 Peng Zhang <sd20@qxwlan.com>
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+
+ model = "Qxwlan E2600AC";
+ compatible = "qcom,ipq4019";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>; /* 256MB */
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2: usb2@60f8800 {
+ status = "okay";
+
+ dwc3@6000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb2_port1: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+ };
+ };
+
+ serial@78af000 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ serial@78b0000 {
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ i2c@78b7000 { /* BLSP1 QUP2 */
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+ };
+
+ usb3: usb3@8af8800 {
+ status = "okay";
+
+ dwc3@8a00000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb3_port1: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+
+ usb3_port2: port@2 {
+ reg = <2>;
+ #trigger-source-cells = <0>;
+ };
+ };
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led1 {
+ label = "e2600ac:green:wlan0";
+ gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
+ };
+
+ led2 {
+ label = "e2600ac:green:wlan1";
+ gpios = <&tlmm 36 GPIO_ACTIVE_LOW>;
+ };
+
+ led3 {
+ label = "e2600ac:green:usb";
+ gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&usb2_port1>, <&usb3_port1>, <&usb3_port2>;
+ linux,default-trigger = "usbport";
+ };
+
+ led4 {
+ label = "e2600ac:green:ctrl1";
+ gpios = <&tlmm 51 GPIO_ACTIVE_LOW>;
+ };
+
+ led5 {
+ label = "e2600ac:green:ctrl2";
+ gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+ };
+
+ led6 {
+ label = "e2600ac:green:ctrl3";
+ gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&tlmm {
+ i2c_0_pins: i2c-0-pinmux {
+ mux {
+ pins = "gpio20", "gpio21";
+ function = "blsp_i2c0";
+ bias-disable;
+ };
+ };
+
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+ mux_2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ serial_0_pins: serial0-pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ serial_1_pins: serial1_pinmux {
+ mux {
+ pins = "gpio8", "gpio9";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pinmux {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "Qxwlan-E2600AC";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "Qxwlan-E2600AC";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/*
+ * Device Tree Source for Linksys EA8300 (Dallas)
+ *
+ * Copyright (C) 2019 Jeff Kletsky
+ *
+ */
+
+/dts-v1/;
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Linksys EA8300 (Dallas)";
+ compatible = "linksys,ea8300", "qcom,ipq4019";
+
+
+ aliases {
+ led-boot = &led_wps_amber;
+ led-failsafe = &led_wps;
+ led-running = &led_linksys;
+ led-upgrade = &led_world;
+ serial0 = &blsp1_uart1;
+ };
+
+
+ leds {
+ compatible = "gpio-leds";
+
+ // Retain node names from running OEM on EA8300
+
+ // Front panel LEDs, top to bottom
+
+ led_plug: diag {
+ label = "ea8300:amber:plug";
+ gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_world: internet {
+ label = "ea8300:amber:world";
+ gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_wps: wps {
+ label = "ea8300:white:wps";
+ gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_wps_amber: wps_amber {
+ label = "ea8300:amber:wps";
+ gpios = <&tlmm 22 GPIO_ACTIVE_HIGH>;
+ panic-indicator;
+ };
+
+ led_linksys: pwr {
+ label = "ea8300:white:linksys";
+ gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+ };
+
+ // On back panel, above USB socket
+
+ led_usb: usb {
+ label = "ea8300:green:usb";
+ gpios = <&tlmm 61 GPIO_ACTIVE_LOW>;
+ trigger-sources = <&usb3_port1>, <&usb3_port2>,
+ <&usb2_port1>;
+ linux,default-trigger = "usbport";
+ };
+ };
+
+
+ keys {
+ compatible = "gpio-keys";
+
+ button@0 {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
+ };
+
+ button@1 {
+ label = "wps";
+ linux,code = <KEY_WPS_BUTTON>;
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+
+ //
+ // OEM U-Boot provides either
+ // init=/sbin/init rootfstype=ubifs ubi.mtd=11,2048 \
+ // root=ubi0:ubifs rootwait rw
+ // or the same with ubi.mtd=13,2048
+ //
+
+ chosen {
+ bootargs-append = " root=/dev/ubiblock0_0 rootfstype=squashfs ro";
+ };
+
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2@60f8800 {
+ status = "okay";
+
+ dwc3@6000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb2_port1: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+ };
+ };
+
+ usb3@8af8800 {
+ status = "okay";
+
+ dwc3@8a00000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb3_port1: port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+
+ usb3_port2: port@2 {
+ reg = <2>;
+ #trigger-source-cells = <0>;
+ };
+ };
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+};
+
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ status = "okay";
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&nand {
+ status = "okay";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "sbl1";
+ reg = <0x0 0x100000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "mibib";
+ reg = <0x100000 0x100000>;
+ read-only;
+ };
+
+ partition@200000 {
+ label = "qsee";
+ reg = <0x200000 0x100000>;
+ read-only;
+ };
+
+ partition@300000 {
+ label = "cdt";
+ reg = <0x300000 0x80000>;
+ read-only;
+ };
+
+ partition@380000 {
+ label = "appsblenv";
+ reg = <0x380000 0x80000>;
+ read-only;
+ };
+
+ partition@400000 {
+ label = "ART";
+ reg = <0x400000 0x80000>;
+ read-only;
+ };
+
+ partition@480000 {
+ label = "appsbl";
+ reg = <0x480000 0x200000>;
+ read-only;
+ };
+
+ partition@680000 {
+ label = "u_env";
+ reg = <0x680000 0x80000>;
+ // writable -- U-Boot environment
+ };
+
+ partition@700000 {
+ label = "s_env";
+ reg = <0x700000 0x40000>;
+ // writable -- Boot counter records
+ };
+
+ partition@740000 {
+ label = "devinfo";
+ reg = <0x740000 0x40000>;
+ read-only;
+ };
+
+ partition@780000 {
+ label = "kernel";
+ reg = <0x780000 0x5800000>;
+ };
+
+ partition@a80000 {
+ label = "rootfs";
+ reg = <0xa80000 0x5500000>;
+ };
+
+ partition@5f80000 {
+ label = "alt_kernel";
+ reg = <0x5f80000 0x5800000>;
+ };
+
+ partition@6280000 {
+ label = "alt_rootfs";
+ reg = <0x6280000 0x5500000>;
+ };
+
+ partition@b780000 {
+ label = "sysdiag";
+ reg = <0xb780000 0x100000>;
+ read-only;
+ };
+
+ partition@b880000 {
+ label = "syscfg";
+ reg = <0xb880000 0x4680000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&pcie0 {
+ status = "okay";
+
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi2: wifi@1,0 {
+ compatible = "qcom,ath10k";
+ reg = <0x00010000 0 0 0 0>;
+ };
+ };
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&tlmm {
+ serial_0_pins: serial0-pinmux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ // gpio61 controls led_usb
+
+ pulldowns {
+ pins = "gpio55", "gpio56", "gpio57",
+ "gpio60", "gpio62", "gpio63",
+ "gpio64", "gpio65", "gpio66",
+ "gpio67", "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "linksys-ea8300-fcc";
+};
+
+&wifi1 {
+ status = "okay";
+ ieee80211-freq-limit = <5170000 5330000>;
+ qcom,ath10k-calibration-variant = "linksys-ea8300-fcc";
+};
+
+&wifi2 {
+ status = "okay";
+ ieee80211-freq-limit = <5490000 5835000>;
+ qcom,ath10k-calibration-variant = "linksys-ea8300-fcc";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "AVM FRITZ!Box 7530";
+ compatible = "avm,fritzbox-7530";
+
+ aliases {
+ led-boot = &power_green;
+ led-failsafe = &info_red;
+ led-running = &power_green;
+ led-upgrade = &info_green;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb3@8af8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ qcom,num_gmac = <1>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wlan {
+ label = "wlan";
+ gpios = <&tlmm 42 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 41 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ dect {
+ label = "dect";
+ gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_PHONE>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ info_red: info_red {
+ label = "fritzbox-7530:red:info";
+ gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+ };
+
+ info_green: info {
+ label = "fritzbox-7530:green:info";
+ gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan {
+ label = "fritzbox-7530:green:wlan";
+ gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+ };
+
+ fon {
+ label = "fritzbox-7530:green:fon";
+ gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ };
+
+ power_green: power {
+ label = "fritzbox-7530:green:power";
+ gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
+ };
+
+ wps {
+ label = "fritzbox-7530:green:wps";
+ gpios = <&tlmm 45 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&tlmm {
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+
+ usb-power {
+ line-name = "enable USB3 power";
+ gpios = <49 GPIO_ACTIVE_HIGH>;
+ gpio-hog;
+ output-high;
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x000000 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "MIBIB";
+ reg = <0x080000 0x80000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "QSEE";
+ reg = <0x100000 0x80000>;
+ read-only;
+ };
+
+ partition@180000 {
+ label = "CDT";
+ reg = <0x180000 0x40000>;
+ read-only;
+ };
+
+ partition@1c0000 {
+ label = "QSEE_B";
+ reg = <0x1c0000 0x80000>;
+ read-only;
+ };
+
+ partition@240000 {
+ label = "urlader0";
+ reg = <0x240000 0x40000>;
+ read-only;
+ };
+
+ partition@280000 {
+ label = "urlader1";
+ reg = <0x280000 0x40000>;
+ read-only;
+ };
+
+ partition@2c0000 {
+ label = "nand-tffs";
+ reg = <0x2c0000 0x840000>;
+ read-only;
+ };
+
+ partition@b00000 {
+ /* 'kernel1' in AVM firmware */
+ label = "uboot0";
+ reg = <0xb00000 0x400000>;
+ };
+
+ partition@f00000 {
+ /* 'kernel2' in AVM firmware */
+ label = "uboot1";
+ reg = <0xf00000 0x400000>;
+ };
+
+ partition@1300000 {
+ label = "ubi";
+ reg = <0x1300000 0x6d00000>;
+ };
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "AVM-FRITZBox-7530";
+};
+
+&pcie0 {
+ status = "okay";
+
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ dsl@1,0 {
+ compatible = "intel,vrx518";
+ status = "okay";
+ reg = <0x00010000 0 0 0 0>;
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "AVM FRITZ!Repeater 1200";
+ compatible = "avm,fritzrepeater-1200";
+
+ aliases {
+ led-boot = &power_green;
+ led-failsafe = &power_red;
+ led-running = &power_green;
+ led-upgrade = &power_red;
+ label-mac-device = &wifi0;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII_RGMII5>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ switch_mac_mode = <0x3>; /* mac mode for RGMII RMII */
+ switch_lan_bmp = <0x0>; /* lan port bitmap */
+ switch_wan_bmp = <0x10>; /* wan port bitmap */
+ };
+
+ edma@c080000 {
+ status = "okay";
+ phy-mode = "rgmii-rxid";
+ qcom,num_gmac = <1>;
+ qcom,single-phy;
+ };
+ };
+
+ key {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "WPS button";
+ gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power_red: power_red {
+ label = "fritzwlan-1200:red:power";
+ gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
+ };
+
+ power_green: power_green {
+ label = "fritzwlan-1200:green:power";
+ gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+ };
+
+ power_yellow {
+ label = "fritzwlan-1200:yellow:power";
+ gpios = <&tlmm 49 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&tlmm {
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+ mux_2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ phy-reset {
+ line-name = "PHY-reset";
+ gpios = <19 GPIO_ACTIVE_HIGH>;
+ gpio-hog;
+ output-high;
+ };
+
+ phy-reset-2 {
+ line-name = "PHY-reset-2";
+ gpios = <47 GPIO_ACTIVE_HIGH>;
+ gpio-hog;
+ output-high;
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "MIBIB";
+ reg = <0x80000 0x80000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "QSEE";
+ reg = <0x100000 0x80000>;
+ read-only;
+ };
+
+ partition@180000 {
+ label = "CDT";
+ reg = <0x180000 0x40000>;
+ read-only;
+ };
+
+ partition@1c0000 {
+ label = "QSEE_B";
+ reg = <0x1c0000 0x80000>;
+ read-only;
+ };
+
+ partition@240000 {
+ label = "urlader0";
+ reg = <0x240000 0x40000>;
+ read-only;
+ };
+
+ partition@280000 {
+ label = "urlader1";
+ reg = <0x280000 0x40000>;
+ read-only;
+ };
+
+ partition@2c0000 {
+ label = "nand-tffs";
+ reg = <0x2c0000 0x840000>;
+ read-only;
+ };
+
+ partition@b00000 {
+ /* 'kernel1' in AVM firmware */
+ label = "uboot0";
+ reg = <0xb00000 0x400000>;
+ };
+
+ partition@f00000 {
+ /* 'kernel2' in AVM firmware */
+ label = "uboot1";
+ reg = <0xf00000 0x400000>;
+ };
+
+ partition@1300000 {
+ label = "ubi";
+ reg = <0x1300000 0x6d00000>;
+ };
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-1200";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-1200";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <0>;
+ qcom,poll_required = <1>;
+ vlan_tag = <0 0x20>;
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "AVM FRITZ!Repeater 3000";
+ compatible = "avm,fritzrepeater-3000";
+
+ aliases {
+ led-boot = &power_led;
+ led-failsafe = &power_led;
+ led-running = &power_led;
+ led-upgrade = &power_led;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+
+ switch_lan_bmp = <0x10>;
+ switch_wan_bmp = <0x20>;
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ key {
+ compatible = "gpio-keys";
+
+ connect {
+ label = "Connect";
+ gpios = <&tlmm 10 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ connect_red {
+ label = "fritzwlan-3000:red:connect";
+ gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+ };
+
+ connect_green {
+ label = "fritzwlan-3000:green:connect";
+ gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+ };
+
+ connect_blue {
+ label = "fritzwlan-3000:blue:connect";
+ gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
+ };
+
+ power_led: power {
+ label = "fritzwlan-3000:green:power";
+ gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&tlmm {
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x000000 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "MIBIB";
+ reg = <0x080000 0x80000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "QSEE";
+ reg = <0x100000 0x80000>;
+ read-only;
+ };
+
+ partition@180000 {
+ label = "CDT";
+ reg = <0x180000 0x40000>;
+ read-only;
+ };
+
+ partition@1c0000 {
+ label = "QSEE_B";
+ reg = <0x1c0000 0x80000>;
+ read-only;
+ };
+
+ partition@240000 {
+ label = "urlader0";
+ reg = <0x240000 0x40000>;
+ read-only;
+ };
+
+ partition@280000 {
+ label = "urlader1";
+ reg = <0x280000 0x40000>;
+ read-only;
+ };
+
+ partition@2c0000 {
+ label = "nand-tffs";
+ reg = <0x2c0000 0x840000>;
+ read-only;
+ };
+
+ partition@b00000 {
+ /* 'kernel1' in AVM firmware */
+ label = "uboot0";
+ reg = <0xb00000 0x400000>;
+ };
+
+ partition@f00000 {
+ /* 'kernel2' in AVM firmware */
+ label = "uboot1";
+ reg = <0xf00000 0x400000>;
+ };
+
+ partition@1300000 {
+ label = "ubi";
+ reg = <0x1300000 0x6d00000>;
+ };
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ /* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
+ qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-3000";
+};
+
+&wifi1 {
+ status = "okay";
+ ieee80211-freq-limit = <5170000 5350000>;
+ /* BDFs are identical for the FRITZ!Box 7530 and the FRITZ!Repeater 3000 */
+ qcom,ath10k-calibration-variant = "AVM-FRITZRepeater-3000";
+};
+
+&pcie0 {
+ status = "okay";
+
+ perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi@1,0 {
+ /* QCA9984 */
+ compatible = "qcom,ath10k";
+ status = "okay";
+ reg = <0x00010000 0 0 0 0>;
+ ieee80211-freq-limit = <5470000 5875000>;
+ /* Uses the reference BDF */
+ };
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/dts-v1/;
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "ASUS Lyra MAP-AC2200";
+ compatible = "asus,map-ac2200";
+
+ aliases {
+ led-boot = &led_blue0;
+ led-failsafe = &led_red0;
+ led-running = &led_blue0;
+ led-upgrade = &led_red0;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2@60f8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "SBL1";
+ reg = <0x0 0x80000>;
+ read-only;
+ };
+
+ partition@80000 {
+ label = "MIBIB";
+ reg = <0x80000 0x80000>;
+ read-only;
+ };
+
+ partition@100000 {
+ label = "QSEE";
+ reg = <0x100000 0x100000>;
+ read-only;
+ };
+
+ partition@200000 {
+ label = "CDT";
+ reg = <0x200000 0x80000>;
+ read-only;
+ };
+
+ partition@280000 {
+ label = "APPSBL";
+ reg = <0x280000 0x140000>;
+ read-only;
+ };
+
+ partition@3c0000 {
+ label = "APPSBLENV";
+ reg = <0x3c0000 0x40000>;
+ read-only;
+ };
+
+ partition@400000 {
+ label = "ubi";
+ reg = <0x400000 0x7c00000>;
+ };
+ };
+ };
+};
+
+&tlmm {
+ i2c_0_pins: i2c_0_pinmux {
+ pinmux {
+ function = "blsp_i2c0";
+ pins = "gpio20", "gpio21";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio52", "gpio53", "gpio58",
+ "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "ASUS-MAP-AC2200";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "ASUS-MAP-AC2200";
+ ieee80211-freq-limit = <5470000 5875000>;
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi2: wifi@1,0 {
+ compatible = "qcom,ath10k";
+ status = "okay";
+ reg = <0x00010000 0 0 0 0>;
+ qcom,ath10k-calibration-variant = "ASUS-MAP-AC2200";
+ ieee80211-freq-limit = <5170000 5350000>;
+ };
+ };
+};
+
+&usb2_hs_phy {
+ /* Bluetooth module attached via USB */
+ status = "okay";
+};
+
+&blsp1_i2c3 {
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ led-controller@32 {
+ /* 9-channel RGB LED controller */
+ compatible = "national,lp5523";
+ reg = <0x32>;
+ clock-mode = [01];
+
+ led_blue0: blue0 {
+ chan-name = "blue0";
+ label = "map-ac2200:blue:chan0";
+ led-cur = [fa];
+ max-cur = [ff];
+ };
+
+ blue1 {
+ chan-name = "blue1";
+ label = "map-ac2200:blue:chan1";
+ led-cur = [fa];
+ max-cur = [ff];
+ };
+
+ blue2 {
+ chan-name = "blue2";
+ label = "map-ac2200:blue:chan2";
+ led-cur = [fa];
+ max-cur = [ff];
+ };
+
+ led_green0: green0 {
+ chan-name = "green0";
+ label = "map-ac2200:green:chan0";
+ led-cur = [fa];
+ max-cur = [ff];
+ };
+
+ green1 {
+ chan-name = "green1";
+ label = "map-ac2200:green:chan1";
+ led-cur = [fa];
+ max-cur = [ff];
+ };
+
+ green2 {
+ chan-name = "green2";
+ label = "map-ac2200:green:chan2";
+ led-cur = [fa];
+ max-cur = [ff];
+ };
+
+ led_red0: red0 {
+ chan-name = "red0";
+ label = "map-ac2200:red:chan0";
+ led-cur = [fa];
+ max-cur = [ff];
+ };
+
+ red1 {
+ chan-name = "red1";
+ label = "map-ac2200:red:chan1";
+ led-cur = [fa];
+ max-cur = [ff];
+ };
+
+ red2 {
+ chan-name = "red2";
+ label = "map-ac2200:red:chan2";
+ led-cur = [fa];
+ max-cur = [ff];
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "qcom-ipq4019-u4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Unielec U4019 (32M)";
+ compatible = "unielec,u4019-32m","unielec,u4019","qcom,ipq4019";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
+
+ flash@0 {
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <24000000>;
+ broken-flash-reset;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "0:SBL1";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+ partition@40000 {
+ label = "0:MIBIB";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+ partition@60000 {
+ label = "0:QSEE";
+ reg = <0x60000 0x60000>;
+ read-only;
+ };
+ partition@c0000 {
+ label = "0:CDT";
+ reg = <0xc0000 0x10000>;
+ read-only;
+ };
+ partition@d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0xd0000 0x10000>;
+ read-only;
+ };
+ partition@e0000 {
+ label = "0:APPSBLENV";
+ reg = <0xe0000 0x10000>;
+ read-only;
+ };
+ partition@f0000 {
+ label = "0:APPSBL";
+ reg = <0xf0000 0x80000>;
+ read-only;
+ };
+ partition@170000 {
+ label = "0:ART";
+ reg = <0x170000 0x10000>;
+ read-only;
+ };
+ partition@180000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x180000 0x1e80000>;
+ };
+ };
+ };
+};
+
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ compatible = "unielec,u4019","qcom,ipq4019";
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <2000>;
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2@60f8800 {
+ status = "okay";
+
+ dwc3@6000000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+ };
+ };
+
+ usb3@8af8800 {
+ status = "okay";
+
+ dwc3@8a00000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@1 {
+ reg = <1>;
+ #trigger-source-cells = <0>;
+ };
+
+ port@2 {
+ reg = <2>;
+ #trigger-source-cells = <0>;
+ };
+ };
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+
+ aliases {
+ led-boot = &led_status;
+ led-failsafe = &led_status;
+ led-running = &led_status;
+ led-upgrade = &led_status;
+ serial0 = &blsp1_uart1;
+ serial1 = &blsp1_uart2;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&led_pins>;
+ pinctrl-names = "default";
+
+ led_status: led2 {
+ label = "u4019:green:led2";
+ gpios = <&tlmm 68 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&blsp1_uart2 {
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&tlmm {
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+ mux_2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ serial_0_pins: serial0-pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+ serial_1_pins: serial1_pinmux {
+ mux {
+ pins = "gpio8", "gpio9";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pinmux {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ led_pins: led_pinmux {
+ mux {
+ function = "gpio";
+ pins = "gpio68";
+ bias-disabled;
+ output-low;
+ };
+ };
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+};
+
+&wifi1 {
+ status = "okay";
+};
--- /dev/null
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Nguyen Dinh Phi <phi_nguyen@compex.com.sg>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Compex WPJ419";
+ compatible = "compex,wpj419", "qcom,ipq4019";
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ reserved-memory {
+ ranges;
+ rsvd1@87000000 {
+ /* Reserved for other subsystem */
+ reg = <0x87000000 0x500000>;
+ no-map;
+ };
+ wifi_dump@87500000 {
+ reg = <0x87500000 0x600000>;
+ no-map;
+ };
+
+ rsvd2@87B00000 {
+ /* Reserved for other subsystem */
+ reg = <0x87B00000 0x500000>;
+ no-map;
+ };
+ };
+
+ chosen {
+ bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1 clk_ignore_unused";
+ };
+
+ soc {
+ pinctrl@1000000 {
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+
+ mux_2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ serial_1_pins: serial1_pinmux {
+ mux {
+ pins = "gpio8", "gpio9", "gpio10", "gpio11";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pinmux {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ bias-disable;
+ };
+
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio12";
+ bias-disable;
+ output-high;
+ };
+ };
+
+ i2c_0_pins: i2c_0_pinmux {
+ mux {
+ pins = "gpio20", "gpio21";
+ function = "blsp_i2c0";
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio52", "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+
+ led_0_pins: led0_pinmux {
+ mux_1 {
+ pins = "gpio36";
+ function = "led0";
+ bias-pull-down;
+ };
+ mux_2 {
+ pins = "gpio40";
+ function = "led4";
+ bias-pull-down;
+ };
+ };
+ };
+
+ blsp_dma: dma@7884000 {
+ status = "okay";
+ };
+
+ spi_0: spi@78b5000 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>, <&tlmm 41 GPIO_ACTIVE_HIGH>;
+ num-cs = <2>;
+
+ flash0@0 {
+ reg = <0>;
+ compatible = "jedec,spi-nor";
+ spi-max-frequency = <24000000>;
+ broken-flash-reset;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "0:SBL1";
+ reg = <0x000000 0x040000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "0:MIBIB";
+ reg = <0x040000 0x020000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "0:QSEE";
+ reg = <0x060000 0x060000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "0:CDT";
+ reg = <0x0c0000 0x010000>;
+ read-only;
+ };
+
+ partition@d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0x0d0000 0x010000>;
+ read-only;
+ };
+
+ partition@e0000 {
+ label = "u-boot-env";
+ reg = <0x0e0000 0x010000>;
+ };
+
+ partition@f0000 {
+ label = "u-boot";
+ reg = <0x0f0000 0x080000>;
+ read-only;
+ };
+
+ partition@170000 {
+ label = "0:ART";
+ reg = <0x170000 0x010000>;
+ read-only;
+ };
+ };
+ };
+
+ nand@1 {
+ reg = <1>;
+ status = "okay";
+ compatible = "spi-nand";
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /* The device has 128MB, but we can only address
+ * 64MB because of the bootloader's default settings.
+ * This is due to the old mt29f driver,
+ * which detected the deivce with only 64MB
+ */
+ partition@0 {
+ label = "ubi";
+ reg = <0x0000000 0x4000000>;
+ };
+ };
+ };
+ };
+
+ mdio@90000 {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ reset-gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <5000>;
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ i2c_0: i2c@78b7000 {
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+ status = "ok";
+ };
+
+ serial@78af000 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ serial@78b0000 {
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ usb3_ss_phy: ssphy@9a000 {
+ status = "okay";
+ };
+
+ usb3_hs_phy: hsphy@a6000 {
+ status = "okay";
+ };
+
+ usb3: usb3@8af8800 {
+ status = "okay";
+ };
+
+ usb2_hs_phy: hsphy@a8000 {
+ status = "okay";
+ };
+
+ usb2: usb2@60f8800 {
+ status = "okay";
+ };
+
+ cryptobam: dma@8e04000 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ switch_lan_bmp = <0x1e>;
+ switch_wan_bmp = <0x20>;
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+
+ qpic_bam: dma@7984000 {
+ status = "okay";
+ };
+
+ pcie0: pci@40000000 {
+ status = "okay";
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+ };
+
+ nand: qpic-nand@79b0000 {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+ };
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <2 0x20>;
+};
+
+&gmac1 {
+ qcom,phy_mdio_addr = <3>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <1 0x10>;
+};
+
+&wifi0 {
+ status = "okay";
+};
+
+&wifi1 {
+ status = "okay";
+};
--- /dev/null
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2017, Christian Mehlis <christian@m3hlis.de>
+ * Copyright (c) 2017-2018, Sven Eckelmann <sven.eckelmann@openmesh.com>
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Compex WPJ428";
+ compatible = "compex,wpj428";
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2: usb2@60f8800 {
+ status = "okay";
+ };
+
+ usb3: usb3@8af8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ switch_lan_bmp = <0x10>;
+ switch_wan_bmp = <0x20>;
+
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ aliases {
+ led-boot = &status;
+ led-failsafe = &status;
+ led-upgrade = &status;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ status: rss4 {
+ label = "wpj428:green:rss4";
+ gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ rss3 {
+ label = "wpj428:green:rss3";
+ gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ beeper: beeper {
+ compatible = "gpio-beeper";
+ gpios = <&tlmm 58 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ m25p80@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition0@0 {
+ label = "0:SBL1";
+ reg = <0x00000000 0x00040000>;
+ read-only;
+ };
+ partition1@40000 {
+ label = "0:MIBIB";
+ reg = <0x00040000 0x00020000>;
+ read-only;
+ };
+ partition2@60000 {
+ label = "0:QSEE";
+ reg = <0x00060000 0x00060000>;
+ read-only;
+ };
+ partition3@c0000 {
+ label = "0:CDT";
+ reg = <0x000c0000 0x00010000>;
+ read-only;
+ };
+ partition4@d0000 {
+ label = "0:DDRPARAMS";
+ reg = <0x000d0000 0x00010000>;
+ read-only;
+ };
+ partition5@e0000 {
+ label = "0:APPSBLENV"; /* uboot env*/
+ reg = <0x000e0000 0x00010000>;
+ read-only;
+ };
+ partition5@f0000 {
+ label = "0:APPSBL"; /* uboot */
+ reg = <0x000f0000 0x00080000>;
+ read-only;
+ };
+ partition5@170000 {
+ label = "0:ART";
+ reg = <0x00170000 0x00010000>;
+ read-only;
+ };
+ partition6@180000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x00180000 0x01e80000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <2 0x20>;
+};
+
+&gmac1 {
+ qcom,phy_mdio_addr = <3>;
+ qcom,poll_required = <1>;
+ qcom,forced_speed = <1000>;
+ qcom,forced_duplex = <1>;
+ vlan_tag = <1 0x10>;
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+};
+
+&wifi1 {
+ status = "okay";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Aruba AP-303";
+ compatible = "aruba,ap-303";
+
+ aliases {
+ led-boot = &led_system_green;
+ led-failsafe = &led_system_red;
+ led-running = &led_system_green;
+ led-upgrade = &led_system_red;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+
+ /delete-node/ ethernet-phy@0;
+ /delete-node/ ethernet-phy@2;
+ /delete-node/ ethernet-phy@3;
+ /delete-node/ ethernet-phy@4;
+
+ ethernet-phy@5 {
+ reg = <0x5>;
+ };
+ };
+
+ counter@4a1000 {
+ compatible = "qcom,qca-gcnt";
+ reg = <0x4a1000 0x4>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII_RGMII5>;
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ switch_mac_mode = <0x3>; /* mac mode for RGMII RMII */
+ switch_lan_bmp = <0x0>; /* lan port bitmap */
+ switch_wan_bmp = <0x10>; /* wan port bitmap */
+ };
+
+ edma@c080000 {
+ qcom,single-phy;
+ qcom,num_gmac = <1>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+ };
+
+ i2c_0: i2c@78b7000 {
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+ status = "ok";
+
+ tpm@29 {
+ /* No Driver */
+ compatible = "atmel,at97sc3203";
+ reg = <0x29>;
+ read-only;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wifi_green {
+ label = "ap-303:green:wifi";
+ gpios = <&tlmm 39 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wifi_amber {
+ label = "ap-303:amber:wifi";
+ gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ led_system_red: system_red {
+ label = "ap-303:red:system";
+ gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_system_green: system_green {
+ label = "ap-303:green:system";
+ gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ gpios = <&tlmm 50 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ /* Texas Instruments CC2540T BLE radio */
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&blsp1_uart2 {
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <5>;
+ qcom,poll_required = <1>;
+ vlan_tag = <0 0x20>;
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&tlmm {
+ /*
+ * In addition to the Pins listed below,
+ * the following GPIOs have "features":
+ * 54 - out - active low to force HW reset
+ * 41 - out - active low to reset TPM
+ * 43 - out - active low to reset BLE radio
+ * 19 - in - active high when DC powered
+ */
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+ mux_2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ nand_pins: nand_pins {
+ pullups {
+ pins = "gpio53", "gpio58", "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio12";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+ i2c_0_pins: i2c_0_pinmux {
+ mux {
+ pins = "gpio10", "gpio11";
+ function = "blsp_i2c0";
+ drive-strength = <4>;
+ bias-disable;
+ };
+ };
+
+ serial_0_pins: serial_0_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ serial_1_pins: serial_1_pinmux {
+ mux {
+ pins = "gpio8", "gpio9";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ phy-reset {
+ line-name = "PHY-reset";
+ gpios = <42 GPIO_ACTIVE_HIGH>;
+ gpio-hog;
+ output-high;
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ /* 'aos0' in Aruba firmware */
+ label = "aos0";
+ reg = <0x0 0x2000000>;
+ read-only;
+ };
+
+ partition@2000000 {
+ /* 'aos1' in AVM firmware */
+ label = "ubi";
+ reg = <0x2000000 0x2000000>;
+ };
+
+ partition@4000000 {
+ label = "aruba-ubifs";
+ reg = <0x4000000 0x4000000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ * There is no partition map for the NOR flash
+ * in the stock firmware.
+ *
+ * All partitions here are based on offsets
+ * found in the U-Boot GPL code and information
+ * from smem.
+ */
+
+ partition@0 {
+ label = "sbl1";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "mibib";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "qsee";
+ reg = <0x60000 0x60000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "cdt";
+ reg = <0xc0000 0x10000>;
+ read-only;
+ };
+
+ partition@d0000 {
+ label = "ddrparams";
+ reg = <0xd0000 0x10000>;
+ read-only;
+ };
+
+ partition@e0000 {
+ label = "ART";
+ reg = <0xe0000 0x10000>;
+ read-only;
+ };
+
+ partition@f0000 {
+ label = "appsbl";
+ reg = <0xf0000 0xf0000>;
+ read-only;
+ };
+
+ partition@1e0000 {
+ label = "mfginfo";
+ reg = <0x1e0000 0x10000>;
+ read-only;
+ };
+
+ partition@1f0000 {
+ label = "apcd";
+ reg = <0x1f0000 0x10000>;
+ read-only;
+ };
+
+ partition@200000 {
+ label = "osss";
+ reg = <0x200000 0x180000>;
+ read-only;
+ };
+
+ partition@380000 {
+ /* This is empty */
+ label = "appsblenv";
+ reg = <0x380000 0x10000>;
+ read-only;
+ };
+
+ partition@390000 {
+ label = "pds";
+ reg = <0x390000 0x10000>;
+ read-only;
+ };
+
+ partition@3a0000 {
+ label = "fcache";
+ reg = <0x3a0000 0x10000>;
+ read-only;
+ };
+
+ partition@3b0000 {
+ /* Called osss1 in smem */
+ label = "u-boot-env-bak";
+ reg = <0x3b0000 0x10000>;
+ read-only;
+ };
+
+ partition@3f0000 {
+ label = "u-boot-env";
+ reg = <0x3f0000 0x10000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "Aruba-AP-303";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "Aruba-AP-303";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Aruba AP-303H";
+ compatible = "aruba,ap-303h";
+
+ aliases {
+ led-boot = &led_system_green;
+ led-failsafe = &led_system_red;
+ led-running = &led_system_green;
+ led-upgrade = &led_system_amber;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+
+ reset-gpios = <&tlmm 19 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <2000>;
+ };
+
+ counter@4a1000 {
+ compatible = "qcom,qca-gcnt";
+ reg = <0x4a1000 0x4>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2@60f8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+
+ i2c_0: i2c@78b7000 {
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+ status = "ok";
+
+ tpm@29 {
+ /* No Driver */
+ compatible = "atmel,at97sc3203";
+ reg = <0x29>;
+ read-only;
+ };
+
+ power-monitor@40 {
+ /* No driver */
+ compatible = "isl,isl28022";
+ reg = <0x40>;
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ wifi_green {
+ label = "ap-303h:green:wifi";
+ gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ wifi_amber {
+ label = "ap-303h:amber:wifi";
+ gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy1tpt";
+ };
+
+ pse {
+ label = "ap-303h:green:pse";
+ gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_system_red: system_red {
+ label = "ap-303h:red:system";
+ gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_system_green: system_green {
+ label = "ap-303h:green:system";
+ gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ led_system_amber: system_amber {
+ label = "ap-303h:amber:system";
+ gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "Reset button";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&blsp1_uart2 {
+ /* Texas Instruments CC2540T BLE radio */
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&tlmm {
+ /*
+ * In addition to the Pins listed below,
+ * the following GPIOs have "features":
+ * 39 - out - active low to force HW reset
+ * 32 - out - active low to reset TPM
+ * 43 - out - active low to reset BLE radio
+ * 41 - out - pulse to set warm reset status
+ * 34 - out - active low to enable PSE port
+ * 22 - in - active low when 802.3at powered
+ * 29 - in - active high when DC powered
+ * 40 - in - active low when reset due to cold HW reset
+ * 30 - in - active low when USB overcurrent detected
+ * 35 - in - interrupt line for power monitor chip
+ * 31 - in - active low when PSE port active
+ */
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+ mux_2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pin {
+ function = "blsp_spi0";
+ pins = "gpio13", "gpio14", "gpio15";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pin_cs {
+ function = "gpio";
+ pins = "gpio12", "gpio59";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+
+ i2c_0_pins: i2c_0_pinmux {
+ mux {
+ pins = "gpio20", "gpio21";
+ function = "blsp_i2c0";
+ drive-strength = <4>;
+ bias-disable;
+ };
+ };
+
+ serial_0_pins: serial_0_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ serial_1_pins: serial_1_pinmux {
+ mux {
+ pins = "gpio8", "gpio9";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ usb-power {
+ line-name = "USB-power";
+ gpios = <23 GPIO_ACTIVE_HIGH>;
+ gpio-hog;
+ output-high;
+ };
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>, <&tlmm 59 GPIO_ACTIVE_HIGH>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ /*
+ * There is no partition map for the NOR flash
+ * in the stock firmware.
+ *
+ * All partitions here are based on offsets
+ * found in the U-Boot GPL code and information
+ * from smem.
+ */
+
+ partition@0 {
+ label = "sbl1";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "mibib";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "qsee";
+ reg = <0x60000 0x60000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "cdt";
+ reg = <0xc0000 0x10000>;
+ read-only;
+ };
+
+ partition@d0000 {
+ label = "ddrparams";
+ reg = <0xd0000 0x10000>;
+ read-only;
+ };
+
+ partition@e0000 {
+ label = "appsblenv";
+ reg = <0xe0000 0x10000>;
+ read-only;
+ };
+
+ partition@f0000 {
+ label = "appsbl";
+ reg = <0xf0000 0x100000>;
+ read-only;
+ };
+
+ partition@1e0000 {
+ label = "ART";
+ reg = <0x1f0000 0x10000>;
+ read-only;
+ };
+
+ partition@1f0000 {
+ label = "osss";
+ reg = <0x200000 0x170000>;
+ read-only;
+ };
+
+ partition@200000 {
+ label = "pds";
+ reg = <0x370000 0x10000>;
+ read-only;
+ };
+
+ partition@380000 {
+ label = "apcd";
+ reg = <0x380000 0x10000>;
+ read-only;
+ };
+
+ partition@390000 {
+ label = "mfginfo";
+ reg = <0x390000 0x10000>;
+ read-only;
+ };
+
+ partition@3a0000 {
+ label = "fcache";
+ reg = <0x3a0000 0x10000>;
+ read-only;
+ };
+
+ partition@3b0000 {
+ /* Called osss1 in smem */
+ label = "u-boot-env-bak";
+ reg = <0x3b0000 0x10000>;
+ read-only;
+ };
+
+ partition@3f0000 {
+ label = "u-boot-env";
+ reg = <0x3c0000 0x40000>;
+ read-only;
+ };
+ };
+ };
+
+ flash@1 {
+ status = "okay";
+
+ compatible = "spi-nand";
+ reg = <1>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ /* 'aos0' in Aruba firmware */
+ label = "aos0";
+ reg = <0x0 0x2000000>;
+ read-only;
+ };
+
+ partition@2000000 {
+ /* 'aos1' in Aruba firmware */
+ label = "ubi";
+ reg = <0x2000000 0x2000000>;
+ };
+
+ partition@4000000 {
+ label = "aruba-ubifs";
+ reg = <0x4000000 0x4000000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "Aruba-AP-303";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "Aruba-AP-303";
+};
--- /dev/null
+/* Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+ * copyright notice and this permission notice appear in all copies.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
+ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ *
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "GL.iNet GL-B1300";
+ compatible = "glinet,gl-b1300";
+
+ aliases {
+ led-boot = &power;
+ led-failsafe = &power;
+ led-running = &power;
+ led-upgrade = &power;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ };
+
+ ess-psgmii@98000 {
+ status = "okay";
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@194b000 {
+ /* select hostmode */
+ compatible = "qcom,tcsr";
+ reg = <0x194b000 0x100>;
+ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+ status = "okay";
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ usb2@60f8800 {
+ status = "okay";
+ };
+
+ usb3@8af8800 {
+ status = "okay";
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ status = "okay";
+ switch_lan_bmp = <0x18>;
+ switch_wan_bmp = <0x20>;
+ };
+
+ edma@c080000 {
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ wps {
+ label = "wps";
+ gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power: power {
+ label = "gl-b1300:green:power";
+ gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ mesh {
+ label = "gl-b1300:green:mesh";
+ gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
+ };
+
+ wlan {
+ label = "gl-b1300:green:wlan";
+ gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&blsp1_spi1 {
+ pinctrl-0 = <&spi_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
+
+ mx25l25635f@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <24000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ SBL1@0 {
+ label = "SBL1";
+ reg = <0x0 0x40000>;
+ read-only;
+ };
+
+ MIBIB@40000 {
+ label = "MIBIB";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+
+ QSEE@60000 {
+ label = "QSEE";
+ reg = <0x60000 0x60000>;
+ read-only;
+ };
+
+ CDT@c0000 {
+ label = "CDT";
+ reg = <0xc0000 0x10000>;
+ read-only;
+ };
+
+ DDRPARAMS@d0000 {
+ label = "DDRPARAMS";
+ reg = <0xd0000 0x10000>;
+ read-only;
+ };
+
+ APPSBLENV@e0000 {
+ label = "APPSBLENV";
+ reg = <0xe0000 0x10000>;
+ read-only;
+ };
+
+ APPSBL@f0000 {
+ label = "APPSBL";
+ reg = <0xf0000 0x80000>;
+ read-only;
+ };
+
+ ART@170000 {
+ label = "ART";
+ reg = <0x170000 0x10000>;
+ read-only;
+ };
+
+ firmware@180000 {
+ compatible = "denx,fit";
+ label = "firmware";
+ reg = <0x180000 0x1e80000>;
+ };
+ };
+ };
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&tlmm {
+ serial_pins: serial_pinmux {
+ mux {
+ pins = "gpio60", "gpio61";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ spi_0_pins: spi_0_pinmux {
+ pinmux {
+ function = "blsp_spi0";
+ pins = "gpio55", "gpio56", "gpio57";
+ };
+ pinmux_cs {
+ function = "gpio";
+ pins = "gpio54";
+ };
+ pinconf {
+ pins = "gpio55", "gpio56", "gpio57";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ pinconf_cs {
+ pins = "gpio54";
+ drive-strength = <2>;
+ bias-disable;
+ output-high;
+ };
+ };
+};
+
+&usb2_hs_phy {
+ status = "okay";
+};
+
+&usb3_hs_phy {
+ status = "okay";
+};
+
+&usb3_ss_phy {
+ status = "okay";
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "GL-B1300";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "GL-B1300";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for Meraki MR33 (Stinkbug)
+ *
+ * Copyright (C) 2017 Chris Blake <chrisrblake93@gmail.com>
+ * Copyright (C) 2017 Christian Lamparter <chunkeey@googlemail.com>
+ *
+ * Based on Cisco Meraki DTS from GPL release r25-linux-3.14-20170427
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without
+ * any warranty of any kind, whether express or implied.
+ */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+ model = "Meraki MR33 Access Point";
+ compatible = "meraki,mr33";
+
+ aliases {
+ led-boot = &status_green;
+ led-failsafe = &status_red;
+ led-running = &status_green;
+ led-upgrade = &power_orange;
+ };
+
+ /* Do we really need this defined? */
+ memory {
+ device_type = "memory";
+ reg = <0x80000000 0x10000000>;
+ };
+
+ soc {
+ rng@22000 {
+ status = "okay";
+ };
+
+ mdio@90000 {
+ status = "okay";
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+ };
+
+ /* It is a 56-bit counter that supplies the count to the ARM arch
+ timers and without upstream driver */
+ counter@4a1000 {
+ compatible = "qcom,qca-gcnt";
+ reg = <0x4a1000 0x4>;
+ };
+
+ ess_tcsr@1953000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1953000 0x1000>;
+ qcom,ess-interface-select = <TCSR_ESS_PSGMII_RGMII5>;
+ };
+
+ tcsr@1949000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1949000 0x100>;
+ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+ };
+
+ tcsr@1957000 {
+ compatible = "qcom,tcsr";
+ reg = <0x1957000 0x100>;
+ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+ };
+
+ serial@78b0000 {
+ pinctrl-0 = <&serial_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ bluetooth {
+ compatible = "ti,cc2650";
+ enable-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ crypto@8e3a000 {
+ status = "okay";
+ };
+
+ watchdog@b017000 {
+ status = "okay";
+ };
+
+ ess-switch@c000000 {
+ switch_mac_mode = <0x3>; /* mac mode for RGMII RMII */
+ switch_lan_bmp = <0x0>; /* lan port bitmap */
+ switch_wan_bmp = <0x10>; /* wan port bitmap */
+ };
+
+ edma@c080000 {
+ qcom,single-phy;
+ qcom,num_gmac = <1>;
+ phy-mode = "rgmii-rxid";
+ status = "okay";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ label = "reset";
+ gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power_orange: power {
+ label = "mr33:orange:power";
+ gpios = <&tlmm 49 GPIO_ACTIVE_LOW>;
+ panic-indicator;
+ };
+ };
+};
+
+&blsp_dma {
+ status = "okay";
+};
+
+&blsp1_uart1 {
+ pinctrl-0 = <&serial_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cryptobam {
+ status = "okay";
+};
+
+&gmac0 {
+ qcom,phy_mdio_addr = <1>;
+ qcom,poll_required = <1>;
+ vlan_tag = <0 0x20>;
+};
+
+&blsp1_i2c3 {
+ pinctrl-0 = <&i2c_0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ at24@50 {
+ compatible = "atmel,24c64";
+ pagesize = <32>;
+ reg = <0x50>;
+ read-only; /* This holds our MAC & Meraki board-data */
+ };
+};
+
+&blsp1_i2c4 {
+ pinctrl-0 = <&i2c_1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ led-controller@30 {
+ compatible = "ti,lp5562";
+ reg = <0x30>;
+ clock-mode = /bits/8 <2>;
+ enable-gpio = <&tlmm 48 GPIO_ACTIVE_HIGH>;
+
+ /* RGB led */
+ status_red: chan0 {
+ chan-name = "mr33:red:status";
+ led-cur = /bits/ 8 <0x20>;
+ max-cur = /bits/ 8 <0x60>;
+ };
+
+ status_green: chan1 {
+ chan-name = "mr33:green:status";
+ led-cur = /bits/ 8 <0x20>;
+ max-cur = /bits/ 8 <0x60>;
+ };
+
+ chan2 {
+ chan-name = "mr33:blue:status";
+ led-cur = /bits/ 8 <0x20>;
+ max-cur = /bits/ 8 <0x60>;
+ };
+
+ chan3 {
+ chan-name = "mr33:white:status";
+ led-cur = /bits/ 8 <0x20>;
+ max-cur = /bits/ 8 <0x60>;
+ };
+ };
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ nand@0 {
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "sbl1";
+ reg = <0x00000000 0x00100000>;
+ read-only;
+ };
+ partition@100000 {
+ label = "mibib";
+ reg = <0x00100000 0x00100000>;
+ read-only;
+ };
+ partition@200000 {
+ label = "bootconfig";
+ reg = <0x00200000 0x00100000>;
+ read-only;
+ };
+ partition@300000 {
+ label = "qsee";
+ reg = <0x00300000 0x00100000>;
+ read-only;
+ };
+ partition@400000 {
+ label = "qsee_alt";
+ reg = <0x00400000 0x00100000>;
+ read-only;
+ };
+ partition@500000 {
+ label = "cdt";
+ reg = <0x00500000 0x00080000>;
+ read-only;
+ };
+ partition@580000 {
+ label = "cdt_alt";
+ reg = <0x00580000 0x00080000>;
+ read-only;
+ };
+ partition@600000 {
+ label = "ddrparams";
+ reg = <0x00600000 0x00080000>;
+ read-only;
+ };
+ partition@700000 {
+ label = "u-boot";
+ reg = <0x00700000 0x00200000>;
+ read-only;
+ };
+ partition@900000 {
+ label = "u-boot-backup";
+ reg = <0x00900000 0x00200000>;
+ read-only;
+ };
+ partition@b00000 {
+ label = "ART";
+ reg = <0x00b00000 0x00080000>;
+ read-only;
+ };
+ partition@c00000 {
+ label = "ubi";
+ reg = <0x00c00000 0x07000000>;
+ /*
+ * Do not try to allocate the remaining
+ * 4 MiB to this ubi partition. It will
+ * confuse the u-boot and it might not
+ * find the kernel partition anymore.
+ */
+ };
+ };
+ };
+};
+
+&pcie0 {
+ status = "okay";
+ perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+ bridge@0,0 {
+ reg = <0x00000000 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ wifi2: wifi@1,0 {
+ compatible = "qcom,ath10k";
+ status = "okay";
+ reg = <0x00010000 0 0 0 0>;
+ };
+ };
+};
+
+&qpic_bam {
+ status = "okay";
+};
+
+&tlmm {
+ /*
+ * GPIO43 should be 0/1 whenever the unit is
+ * powered through PoE or AC-Adapter.
+ * That said, playing with this seems to
+ * reset the AP.
+ */
+
+ mdio_pins: mdio_pinmux {
+ mux_1 {
+ pins = "gpio6";
+ function = "mdio";
+ bias-pull-up;
+ };
+ mux_2 {
+ pins = "gpio7";
+ function = "mdc";
+ bias-pull-up;
+ };
+ };
+
+ serial_0_pins: serial_pinmux {
+ mux {
+ pins = "gpio16", "gpio17";
+ function = "blsp_uart0";
+ bias-disable;
+ };
+ };
+
+ serial_1_pins: serial1_pinmux {
+ mux {
+ /* We use the i2c-0 pins for serial_1 */
+ pins = "gpio8", "gpio9";
+ function = "blsp_uart1";
+ bias-disable;
+ };
+ };
+
+ i2c_0_pins: i2c_0_pinmux {
+ pinmux {
+ function = "blsp_i2c0";
+ pins = "gpio20", "gpio21";
+ };
+ pinconf {
+ pins = "gpio20", "gpio21";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ i2c_1_pins: i2c_1_pinmux {
+ pinmux {
+ function = "blsp_i2c1";
+ pins = "gpio34", "gpio35";
+ };
+ pinconf {
+ pins = "gpio34", "gpio35";
+ drive-strength = <16>;
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ /*
+ * There are 18 pins. 15 pins are common between LCD and NAND.
+ * The QPIC controller arbitrates between LCD and NAND. Of the
+ * remaining 4, 2 are for NAND and 2 are for LCD exclusively.
+ *
+ * The meraki source hints that the bluetooth module claims
+ * pin 52 as well. But sadly, there's no data whenever this
+ * is a NAND or LCD exclusive pin or not.
+ */
+
+ pullups {
+ pins = "gpio52", "gpio53", "gpio58",
+ "gpio59";
+ function = "qpic";
+ bias-pull-up;
+ };
+
+ pulldowns {
+ pins = "gpio54", "gpio55", "gpio56",
+ "gpio57", "gpio60", "gpio61",
+ "gpio62", "gpio63", "gpio64",
+ "gpio65", "gpio66", "gpio67",
+ "gpio68", "gpio69";
+ function = "qpic";
+ bias-pull-down;
+ };
+ };
+};
+
+&wifi0 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "Meraki-MR33";
+};
+
+&wifi1 {
+ status = "okay";
+ qcom,ath10k-calibration-variant = "Meraki-MR33";
+};
--- /dev/null
+#
+## Makefile for the Qualcomm Atheros ethernet edma driver
+#
+
+
+obj-$(CONFIG_ESSEDMA) += essedma.o
+
+essedma-objs := edma_axi.o edma.o edma_ethtool.o
+
--- /dev/null
+/*
+ * Copyright (c) 2014 - 2016, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for
+ * any purpose with or without fee is hereby granted, provided that the
+ * above copyright notice and this permission notice appear in all copies.
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT
+ * OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include <linux/platform_device.h>
+#include <linux/if_vlan.h>
+#include "ess_edma.h"
+#include "edma.h"
+
+extern struct net_device *edma_netdev[EDMA_MAX_PORTID_SUPPORTED];
+bool edma_stp_rstp;
+u16 edma_ath_eth_type;
+
+/* edma_skb_priority_offset()
+ * get edma skb priority
+ */
+static unsigned int edma_skb_priority_offset(struct sk_buff *skb)
+{
+ return (skb->priority >> 2) & 1;
+}
+
+/* edma_alloc_tx_ring()
+ * Allocate Tx descriptors ring
+ */
+static int edma_alloc_tx_ring(struct edma_common_info *edma_cinfo,
+ struct edma_tx_desc_ring *etdr)
+{
+ struct platform_device *pdev = edma_cinfo->pdev;
+
+ /* Initialize ring */
+ etdr->size = sizeof(struct edma_sw_desc) * etdr->count;
+ etdr->sw_next_to_fill = 0;
+ etdr->sw_next_to_clean = 0;
+
+ /* Allocate SW descriptors */
+ etdr->sw_desc = vzalloc(etdr->size);
+ if (!etdr->sw_desc) {
+ dev_err(&pdev->dev, "buffer alloc of tx ring failed=%p", etdr);
+ return -ENOMEM;
+ }
+
+ /* Allocate HW descriptors */
+ etdr->hw_desc = dma_alloc_coherent(&pdev->dev, etdr->size, &etdr->dma,
+ GFP_KERNEL);
+ if (!etdr->hw_desc) {
+ dev_err(&pdev->dev, "descriptor allocation for tx ring failed");
+ vfree(etdr->sw_desc);
+ return -ENOMEM;
+ }
+
+ return 0;
+}
+
+/* edma_free_tx_ring()
+ * Free tx rings allocated by edma_alloc_tx_rings
+ */
+static void edma_free_tx_ring(struct edma_common_info *edma_cinfo,
+ struct edma_tx_desc_ring *etdr)
+{
+ struct platform_device *pdev = edma_cinfo->pdev;
+
+ if (likely(etdr->dma))
+ dma_free_coherent(&pdev->dev, etdr->size, etdr->hw_desc,
+ etdr->dma);
+
+ vfree(etdr->sw_desc);
+ etdr->sw_desc = NULL;
+}
+
+/* edma_alloc_rx_ring()
+ * allocate rx descriptor ring
+ */
+static int edma_alloc_rx_ring(struct edma_common_info *edma_cinfo,
+ struct edma_rfd_desc_ring *erxd)
+{
+ struct platform_device *pdev = edma_cinfo->pdev;
+
+ erxd->size = sizeof(struct edma_sw_desc) * erxd->count;
+ erxd->sw_next_to_fill = 0;
+ erxd->sw_next_to_clean = 0;
+
+ /* Allocate SW descriptors */
+ erxd->sw_desc = vzalloc(erxd->size);
+ if (!erxd->sw_desc)
+ return -ENOMEM;
+
+ /* Alloc HW descriptors */
+ erxd->hw_desc = dma_alloc_coherent(&pdev->dev, erxd->size, &erxd->dma,
+ GFP_KERNEL);
+ if (!erxd->hw_desc) {
+ vfree(erxd->sw_desc);
+ return -ENOMEM;
+ }
+
+ /* Initialize pending_fill */
+ erxd->pending_fill = 0;
+
+ return 0;
+}
+
+/* edma_free_rx_ring()
+ * Free rx ring allocated by alloc_rx_ring
+ */
+static void edma_free_rx_ring(struct edma_common_info *edma_cinfo,
+ struct edma_rfd_desc_ring *rxdr)
+{
+ struct platform_device *pdev = edma_cinfo->pdev;
+
+ if (likely(rxdr->dma))
+ dma_free_coherent(&pdev->dev, rxdr->size, rxdr->hw_desc,
+ rxdr->dma);
+
+ vfree(rxdr->sw_desc);
+ rxdr->sw_desc = NULL;
+}
+
+/* edma_configure_tx()
+ * Configure transmission control data
+ */
+static void edma_configure_tx(struct edma_common_info *edma_cinfo)
+{
+ u32 txq_ctrl_data;
+
+ txq_ctrl_data = (EDMA_TPD_BURST << EDMA_TXQ_NUM_TPD_BURST_SHIFT);
+ txq_ctrl_data |= EDMA_TXQ_CTRL_TPD_BURST_EN;
+ txq_ctrl_data |= (EDMA_TXF_BURST << EDMA_TXQ_TXF_BURST_NUM_SHIFT);
+ edma_write_reg(EDMA_REG_TXQ_CTRL, txq_ctrl_data);
+}
+
+
+/* edma_configure_rx()
+ * configure reception control data
+ */
+static void edma_configure_rx(struct edma_common_info *edma_cinfo)
+{
+ struct edma_hw *hw = &edma_cinfo->hw;
+ u32 rss_type, rx_desc1, rxq_ctrl_data;
+
+ /* Set RSS type */
+ rss_type = hw->rss_type;
+ edma_write_reg(EDMA_REG_RSS_TYPE, rss_type);
+
+ /* Set RFD burst number */
+ rx_desc1 = (EDMA_RFD_BURST << EDMA_RXQ_RFD_BURST_NUM_SHIFT);
+
+ /* Set RFD prefetch threshold */
+ rx_desc1 |= (EDMA_RFD_THR << EDMA_RXQ_RFD_PF_THRESH_SHIFT);
+
+ /* Set RFD in host ring low threshold to generte interrupt */
+ rx_desc1 |= (EDMA_RFD_LTHR << EDMA_RXQ_RFD_LOW_THRESH_SHIFT);
+ edma_write_reg(EDMA_REG_RX_DESC1, rx_desc1);
+
+ /* Set Rx FIFO threshold to start to DMA data to host */
+ rxq_ctrl_data = EDMA_FIFO_THRESH_128_BYTE;
+
+ if (!edma_cinfo->is_single_phy) {
+ /* Set RX remove vlan bit */
+ rxq_ctrl_data |= EDMA_RXQ_CTRL_RMV_VLAN;
+ }
+
+ edma_write_reg(EDMA_REG_RXQ_CTRL, rxq_ctrl_data);
+}
+
+/* edma_alloc_rx_buf()
+ * does skb allocation for the received packets.
+ */
+static int edma_alloc_rx_buf(struct edma_common_info
+ *edma_cinfo,
+ struct edma_rfd_desc_ring *erdr,
+ int cleaned_count, int queue_id)
+{
+ struct platform_device *pdev = edma_cinfo->pdev;
+ struct edma_rx_free_desc *rx_desc;
+ struct edma_sw_desc *sw_desc;
+ struct sk_buff *skb;
+ unsigned int i;
+ u16 prod_idx, length;
+ u32 reg_data;
+
+ if (cleaned_count > erdr->count)
+ cleaned_count = erdr->count - 1;
+
+ i = erdr->sw_next_to_fill;
+
+ while (cleaned_count) {
+ sw_desc = &erdr->sw_desc[i];
+ length = edma_cinfo->rx_head_buffer_len;
+
+ if (sw_desc->flags & EDMA_SW_DESC_FLAG_SKB_REUSE) {
+ skb = sw_desc->skb;
+
+ /* Clear REUSE Flag */
+ sw_desc->flags &= ~EDMA_SW_DESC_FLAG_SKB_REUSE;
+ } else {
+ /* alloc skb */
+ skb = netdev_alloc_skb_ip_align(edma_netdev[0], length);
+ if (!skb) {
+ /* Better luck next round */
+ break;
+ }
+ }
+
+ if (edma_cinfo->page_mode) {
+ struct page *pg = alloc_page(GFP_ATOMIC);
+
+ if (!pg) {
+ dev_kfree_skb_any(skb);
+ break;
+ }
+
+ sw_desc->dma = dma_map_page(&pdev->dev, pg, 0,
+ edma_cinfo->rx_page_buffer_len,
+ DMA_FROM_DEVICE);
+ if (dma_mapping_error(&pdev->dev,
+ sw_desc->dma)) {
+ __free_page(pg);
+ dev_kfree_skb_any(skb);
+ break;
+ }
+
+ skb_fill_page_desc(skb, 0, pg, 0,
+ edma_cinfo->rx_page_buffer_len);
+ sw_desc->flags = EDMA_SW_DESC_FLAG_SKB_FRAG;
+ sw_desc->length = edma_cinfo->rx_page_buffer_len;
+ } else {
+ sw_desc->dma = dma_map_single(&pdev->dev, skb->data,
+ length, DMA_FROM_DEVICE);
+ if (dma_mapping_error(&pdev->dev,
+ sw_desc->dma)) {
+ dev_kfree_skb_any(skb);
+ break;
+ }
+
+ sw_desc->flags = EDMA_SW_DESC_FLAG_SKB_HEAD;
+ sw_desc->length = length;
+ }
+
+ /* Update the buffer info */
+ sw_desc->skb = skb;
+ rx_desc = (&((struct edma_rx_free_desc *)(erdr->hw_desc))[i]);
+ rx_desc->buffer_addr = cpu_to_le64(sw_desc->dma);
+ if (++i == erdr->count)
+ i = 0;
+ cleaned_count--;
+ }
+
+ erdr->sw_next_to_fill = i;
+
+ if (i == 0)
+ prod_idx = erdr->count - 1;
+ else
+ prod_idx = i - 1;
+
+ /* Update the producer index */
+ edma_read_reg(EDMA_REG_RFD_IDX_Q(queue_id), ®_data);
+ reg_data &= ~EDMA_RFD_PROD_IDX_BITS;
+ reg_data |= prod_idx;
+ edma_write_reg(EDMA_REG_RFD_IDX_Q(queue_id), reg_data);
+
+ /* If we couldn't allocate all the buffers
+ * we increment the alloc failure counters
+ */
+ if (cleaned_count)
+ edma_cinfo->edma_ethstats.rx_alloc_fail_ctr++;
+
+ return cleaned_count;
+}
+
+/* edma_init_desc()
+ * update descriptor ring size, buffer and producer/consumer index
+ */
+static void edma_init_desc(struct edma_common_info *edma_cinfo)
+{
+ struct edma_rfd_desc_ring *rfd_ring;
+ struct edma_tx_desc_ring *etdr;
+ int i = 0, j = 0;
+ u32 data = 0;
+ u16 hw_cons_idx = 0;
+
+ /* Set the base address of every TPD ring. */
+ for (i = 0; i < edma_cinfo->num_tx_queues; i++) {
+ etdr = edma_cinfo->tpd_ring[i];
+
+ /* Update descriptor ring base address */
+ edma_write_reg(EDMA_REG_TPD_BASE_ADDR_Q(i), (u32)etdr->dma);
+ edma_read_reg(EDMA_REG_TPD_IDX_Q(i), &data);
+
+ /* Calculate hardware consumer index */
+ hw_cons_idx = (data >> EDMA_TPD_CONS_IDX_SHIFT) & 0xffff;
+ etdr->sw_next_to_fill = hw_cons_idx;
+ etdr->sw_next_to_clean = hw_cons_idx;
+ data &= ~(EDMA_TPD_PROD_IDX_MASK << EDMA_TPD_PROD_IDX_SHIFT);
+ data |= hw_cons_idx;
+
+ /* update producer index */
+ edma_write_reg(EDMA_REG_TPD_IDX_Q(i), data);
+
+ /* update SW consumer index register */
+ edma_write_reg(EDMA_REG_TX_SW_CONS_IDX_Q(i), hw_cons_idx);
+
+ /* Set TPD ring size */
+ edma_write_reg(EDMA_REG_TPD_RING_SIZE,
+ edma_cinfo->tx_ring_count &
+ EDMA_TPD_RING_SIZE_MASK);
+ }
+
+ for (i = 0, j = 0; i < edma_cinfo->num_rx_queues; i++) {
+ rfd_ring = edma_cinfo->rfd_ring[j];
+ /* Update Receive Free descriptor ring base address */
+ edma_write_reg(EDMA_REG_RFD_BASE_ADDR_Q(j),
+ (u32)(rfd_ring->dma));
+ j += ((edma_cinfo->num_rx_queues == 4) ? 2 : 1);
+ }
+
+ data = edma_cinfo->rx_head_buffer_len;
+ if (edma_cinfo->page_mode)
+ data = edma_cinfo->rx_page_buffer_len;
+
+ data &= EDMA_RX_BUF_SIZE_MASK;
+ data <<= EDMA_RX_BUF_SIZE_SHIFT;
+
+ /* Update RFD ring size and RX buffer size */
+ data |= (edma_cinfo->rx_ring_count & EDMA_RFD_RING_SIZE_MASK)
+ << EDMA_RFD_RING_SIZE_SHIFT;
+
+ edma_write_reg(EDMA_REG_RX_DESC0, data);
+
+ /* Disable TX FIFO low watermark and high watermark */
+ edma_write_reg(EDMA_REG_TXF_WATER_MARK, 0);
+
+ /* Load all of base address above */
+ edma_read_reg(EDMA_REG_TX_SRAM_PART, &data);
+ data |= 1 << EDMA_LOAD_PTR_SHIFT;
+ edma_write_reg(EDMA_REG_TX_SRAM_PART, data);
+}
+
+/* edma_receive_checksum
+ * Api to check checksum on receive packets
+ */
+static void edma_receive_checksum(struct edma_rx_return_desc *rd,
+ struct sk_buff *skb)
+{
+ skb_checksum_none_assert(skb);
+
+ /* check the RRD IP/L4 checksum bit to see if
+ * its set, which in turn indicates checksum
+ * failure.
+ */
+ if (rd->rrd6 & EDMA_RRD_CSUM_FAIL_MASK)
+ return;
+
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+}
+
+/* edma_clean_rfd()
+ * clean up rx resourcers on error
+ */
+static void edma_clean_rfd(struct edma_rfd_desc_ring *erdr, u16 index)
+{
+ struct edma_rx_free_desc *rx_desc;
+ struct edma_sw_desc *sw_desc;
+
+ rx_desc = (&((struct edma_rx_free_desc *)(erdr->hw_desc))[index]);
+ sw_desc = &erdr->sw_desc[index];
+ if (sw_desc->skb) {
+ dev_kfree_skb_any(sw_desc->skb);
+ sw_desc->skb = NULL;
+ }
+
+ memset(rx_desc, 0, sizeof(struct edma_rx_free_desc));
+}
+
+/* edma_rx_complete_fraglist()
+ * Complete Rx processing for fraglist skbs
+ */
+static void edma_rx_complete_stp_rstp(struct sk_buff *skb, int port_id, struct edma_rx_return_desc *rd)
+{
+ int i;
+ u32 priority;
+ u16 port_type;
+ u8 mac_addr[EDMA_ETH_HDR_LEN];
+
+ port_type = (rd->rrd1 >> EDMA_RRD_PORT_TYPE_SHIFT)
+ & EDMA_RRD_PORT_TYPE_MASK;
+ /* if port type is 0x4, then only proceed with
+ * other stp/rstp calculation
+ */
+ if (port_type == EDMA_RX_ATH_HDR_RSTP_PORT_TYPE) {
+ u8 bpdu_mac[6] = {0x01, 0x80, 0xc2, 0x00, 0x00, 0x00};
+
+ /* calculate the frame priority */
+ priority = (rd->rrd1 >> EDMA_RRD_PRIORITY_SHIFT)
+ & EDMA_RRD_PRIORITY_MASK;
+
+ for (i = 0; i < EDMA_ETH_HDR_LEN; i++)
+ mac_addr[i] = skb->data[i];
+
+ /* Check if destination mac addr is bpdu addr */
+ if (!memcmp(mac_addr, bpdu_mac, 6)) {
+ /* destination mac address is BPDU
+ * destination mac address, then add
+ * atheros header to the packet.
+ */
+ u16 athr_hdr = (EDMA_RX_ATH_HDR_VERSION << EDMA_RX_ATH_HDR_VERSION_SHIFT) |
+ (priority << EDMA_RX_ATH_HDR_PRIORITY_SHIFT) |
+ (EDMA_RX_ATH_HDR_RSTP_PORT_TYPE << EDMA_RX_ATH_PORT_TYPE_SHIFT) | port_id;
+ skb_push(skb, 4);
+ memcpy(skb->data, mac_addr, EDMA_ETH_HDR_LEN);
+ *(uint16_t *)&skb->data[12] = htons(edma_ath_eth_type);
+ *(uint16_t *)&skb->data[14] = htons(athr_hdr);
+ }
+ }
+}
+
+/*
+ * edma_rx_complete_fraglist()
+ * Complete Rx processing for fraglist skbs
+ */
+static int edma_rx_complete_fraglist(struct sk_buff *skb, u16 num_rfds, u16 length, u32 sw_next_to_clean,
+ u16 *cleaned_count, struct edma_rfd_desc_ring *erdr, struct edma_common_info *edma_cinfo)
+{
+ struct platform_device *pdev = edma_cinfo->pdev;
+ struct edma_hw *hw = &edma_cinfo->hw;
+ struct sk_buff *skb_temp;
+ struct edma_sw_desc *sw_desc;
+ int i;
+ u16 size_remaining;
+
+ skb->data_len = 0;
+ skb->tail += (hw->rx_head_buff_size - 16);
+ skb->len = skb->truesize = length;
+ size_remaining = length - (hw->rx_head_buff_size - 16);
+
+ /* clean-up all related sw_descs */
+ for (i = 1; i < num_rfds; i++) {
+ struct sk_buff *skb_prev;
+ sw_desc = &erdr->sw_desc[sw_next_to_clean];
+ skb_temp = sw_desc->skb;
+
+ dma_unmap_single(&pdev->dev, sw_desc->dma,
+ sw_desc->length, DMA_FROM_DEVICE);
+
+ if (size_remaining < hw->rx_head_buff_size)
+ skb_put(skb_temp, size_remaining);
+ else
+ skb_put(skb_temp, hw->rx_head_buff_size);
+
+ /*
+ * If we are processing the first rfd, we link
+ * skb->frag_list to the skb corresponding to the
+ * first RFD
+ */
+ if (i == 1)
+ skb_shinfo(skb)->frag_list = skb_temp;
+ else
+ skb_prev->next = skb_temp;
+ skb_prev = skb_temp;
+ skb_temp->next = NULL;
+
+ skb->data_len += skb_temp->len;
+ size_remaining -= skb_temp->len;
+
+ /* Increment SW index */
+ sw_next_to_clean = (sw_next_to_clean + 1) & (erdr->count - 1);
+ (*cleaned_count)++;
+ }
+
+ return sw_next_to_clean;
+}
+
+/* edma_rx_complete_paged()
+ * Complete Rx processing for paged skbs
+ */
+static int edma_rx_complete_paged(struct sk_buff *skb, u16 num_rfds, u16 length, u32 sw_next_to_clean,
+ u16 *cleaned_count, struct edma_rfd_desc_ring *erdr, struct edma_common_info *edma_cinfo)
+{
+ struct platform_device *pdev = edma_cinfo->pdev;
+ struct sk_buff *skb_temp;
+ struct edma_sw_desc *sw_desc;
+ int i;
+ u16 size_remaining;
+
+ skb_frag_t *frag = &skb_shinfo(skb)->frags[0];
+
+ /* Setup skbuff fields */
+ skb->len = length;
+
+ if (likely(num_rfds <= 1)) {
+ skb->data_len = length;
+ skb->truesize += edma_cinfo->rx_page_buffer_len;
+ skb_fill_page_desc(skb, 0, skb_frag_page(frag),
+ 16, length);
+ } else {
+ skb_frag_size_sub(frag, 16);
+ skb->data_len = skb_frag_size(frag);
+ skb->truesize += edma_cinfo->rx_page_buffer_len;
+ size_remaining = length - skb_frag_size(frag);
+
+ skb_fill_page_desc(skb, 0, skb_frag_page(frag),
+ 16, skb_frag_size(frag));
+
+ /* clean-up all related sw_descs */
+ for (i = 1; i < num_rfds; i++) {
+ sw_desc = &erdr->sw_desc[sw_next_to_clean];
+ skb_temp = sw_desc->skb;
+ frag = &skb_shinfo(skb_temp)->frags[0];
+ dma_unmap_page(&pdev->dev, sw_desc->dma,
+ sw_desc->length, DMA_FROM_DEVICE);
+
+ if (size_remaining < edma_cinfo->rx_page_buffer_len)
+ skb_frag_size_set(frag, size_remaining);
+
+ skb_fill_page_desc(skb, i, skb_frag_page(frag),
+ 0, skb_frag_size(frag));
+
+ skb_shinfo(skb_temp)->nr_frags = 0;
+ dev_kfree_skb_any(skb_temp);
+
+ skb->data_len += skb_frag_size(frag);
+ skb->truesize += edma_cinfo->rx_page_buffer_len;
+ size_remaining -= skb_frag_size(frag);
+
+ /* Increment SW index */
+ sw_next_to_clean = (sw_next_to_clean + 1) & (erdr->count - 1);
+ (*cleaned_count)++;
+ }
+ }
+
+ return sw_next_to_clean;
+}
+
+/*
+ * edma_rx_complete()
+ * Main api called from the poll function to process rx packets.
+ */
+static u16 edma_rx_complete(struct edma_common_info *edma_cinfo,
+ int *work_done, int work_to_do, int queue_id,
+ struct napi_struct *napi)
+{
+ struct platform_device *pdev = edma_cinfo->pdev;
+ struct edma_rfd_desc_ring *erdr = edma_cinfo->rfd_ring[queue_id];
+ struct net_device *netdev;
+ struct edma_adapter *adapter;
+ struct edma_sw_desc *sw_desc;
+ struct sk_buff *skb;
+ struct edma_rx_return_desc *rd;
+ u16 hash_type, rrd[8], cleaned_count = 0, length = 0, num_rfds = 1,
+ sw_next_to_clean, hw_next_to_clean = 0, vlan = 0, ret_count = 0;
+ u32 data = 0;
+ u8 *vaddr;
+ int port_id, i, drop_count = 0;
+ u32 priority;
+ u16 count = erdr->count, rfd_avail;
+ u8 queue_to_rxid[8] = {0, 0, 1, 1, 2, 2, 3, 3};
+
+ cleaned_count = erdr->pending_fill;
+ sw_next_to_clean = erdr->sw_next_to_clean;
+
+ edma_read_reg(EDMA_REG_RFD_IDX_Q(queue_id), &data);
+ hw_next_to_clean = (data >> EDMA_RFD_CONS_IDX_SHIFT) &
+ EDMA_RFD_CONS_IDX_MASK;
+
+ do {
+ while (sw_next_to_clean != hw_next_to_clean) {
+ if (!work_to_do)
+ break;
+
+ sw_desc = &erdr->sw_desc[sw_next_to_clean];
+ skb = sw_desc->skb;
+
+ /* Unmap the allocated buffer */
+ if (likely(sw_desc->flags & EDMA_SW_DESC_FLAG_SKB_HEAD))
+ dma_unmap_single(&pdev->dev, sw_desc->dma,
+ sw_desc->length, DMA_FROM_DEVICE);
+ else
+ dma_unmap_page(&pdev->dev, sw_desc->dma,
+ sw_desc->length, DMA_FROM_DEVICE);
+
+ /* Get RRD */
+ if (edma_cinfo->page_mode) {
+ vaddr = kmap_atomic(skb_frag_page(&skb_shinfo(skb)->frags[0]));
+ memcpy((uint8_t *)&rrd[0], vaddr, 16);
+ rd = (struct edma_rx_return_desc *)rrd;
+ kunmap_atomic(vaddr);
+ } else {
+ rd = (struct edma_rx_return_desc *)skb->data;
+ }
+
+ /* Check if RRD is valid */
+ if (!(rd->rrd7 & EDMA_RRD_DESC_VALID)) {
+ edma_clean_rfd(erdr, sw_next_to_clean);
+ sw_next_to_clean = (sw_next_to_clean + 1) &
+ (erdr->count - 1);
+ cleaned_count++;
+ continue;
+ }
+
+ /* Get the number of RFDs from RRD */
+ num_rfds = rd->rrd1 & EDMA_RRD_NUM_RFD_MASK;
+
+ /* Get Rx port ID from switch */
+ port_id = (rd->rrd1 >> EDMA_PORT_ID_SHIFT) & EDMA_PORT_ID_MASK;
+ if ((!port_id) || (port_id > EDMA_MAX_PORTID_SUPPORTED)) {
+ dev_err(&pdev->dev, "Invalid RRD source port bit set");
+ for (i = 0; i < num_rfds; i++) {
+ edma_clean_rfd(erdr, sw_next_to_clean);
+ sw_next_to_clean = (sw_next_to_clean + 1) & (erdr->count - 1);
+ cleaned_count++;
+ }
+ continue;
+ }
+
+ /* check if we have a sink for the data we receive.
+ * If the interface isn't setup, we have to drop the
+ * incoming data for now.
+ */
+ netdev = edma_cinfo->portid_netdev_lookup_tbl[port_id];
+ if (!netdev) {
+ edma_clean_rfd(erdr, sw_next_to_clean);
+ sw_next_to_clean = (sw_next_to_clean + 1) &
+ (erdr->count - 1);
+ cleaned_count++;
+ continue;
+ }
+ adapter = netdev_priv(netdev);
+
+ /* This code is added to handle a usecase where high
+ * priority stream and a low priority stream are
+ * received simultaneously on DUT. The problem occurs
+ * if one of the Rx rings is full and the corresponding
+ * core is busy with other stuff. This causes ESS CPU
+ * port to backpressure all incoming traffic including
+ * high priority one. We monitor free descriptor count
+ * on each CPU and whenever it reaches threshold (< 80),
+ * we drop all low priority traffic and let only high
+ * priotiy traffic pass through. We can hence avoid
+ * ESS CPU port to send backpressure on high priroity
+ * stream.
+ */
+ priority = (rd->rrd1 >> EDMA_RRD_PRIORITY_SHIFT)
+ & EDMA_RRD_PRIORITY_MASK;
+ if (likely(!priority && !edma_cinfo->page_mode && (num_rfds <= 1))) {
+ rfd_avail = (count + sw_next_to_clean - hw_next_to_clean - 1) & (count - 1);
+ if (rfd_avail < EDMA_RFD_AVAIL_THR) {
+ sw_desc->flags = EDMA_SW_DESC_FLAG_SKB_REUSE;
+ sw_next_to_clean = (sw_next_to_clean + 1) & (erdr->count - 1);
+ adapter->stats.rx_dropped++;
+ cleaned_count++;
+ drop_count++;
+ if (drop_count == 3) {
+ work_to_do--;
+ (*work_done)++;
+ drop_count = 0;
+ }
+ if (cleaned_count >= EDMA_RX_BUFFER_WRITE) {
+ /* If buffer clean count reaches 16, we replenish HW buffers. */
+ ret_count = edma_alloc_rx_buf(edma_cinfo, erdr, cleaned_count, queue_id);
+ edma_write_reg(EDMA_REG_RX_SW_CONS_IDX_Q(queue_id),
+ sw_next_to_clean);
+ cleaned_count = ret_count;
+ erdr->pending_fill = ret_count;
+ }
+ continue;
+ }
+ }
+
+ work_to_do--;
+ (*work_done)++;
+
+ /* Increment SW index */
+ sw_next_to_clean = (sw_next_to_clean + 1) &
+ (erdr->count - 1);
+
+ cleaned_count++;
+
+ /* Get the packet size and allocate buffer */
+ length = rd->rrd6 & EDMA_RRD_PKT_SIZE_MASK;
+
+ if (edma_cinfo->page_mode) {
+ /* paged skb */
+ sw_next_to_clean = edma_rx_complete_paged(skb, num_rfds, length, sw_next_to_clean, &cleaned_count, erdr, edma_cinfo);
+ if (!pskb_may_pull(skb, ETH_HLEN)) {
+ dev_kfree_skb_any(skb);
+ continue;
+ }
+ } else {
+ /* single or fraglist skb */
+
+ /* Addition of 16 bytes is required, as in the packet
+ * first 16 bytes are rrd descriptors, so actual data
+ * starts from an offset of 16.
+ */
+ skb_reserve(skb, 16);
+ if (likely((num_rfds <= 1) || !edma_cinfo->fraglist_mode)) {
+ skb_put(skb, length);
+ } else {
+ sw_next_to_clean = edma_rx_complete_fraglist(skb, num_rfds, length, sw_next_to_clean, &cleaned_count, erdr, edma_cinfo);
+ }
+ }
+
+ if (edma_stp_rstp) {
+ edma_rx_complete_stp_rstp(skb, port_id, rd);
+ }
+
+ skb->protocol = eth_type_trans(skb, netdev);
+
+ /* Record Rx queue for RFS/RPS and fill flow hash from HW */
+ skb_record_rx_queue(skb, queue_to_rxid[queue_id]);
+ if (netdev->features & NETIF_F_RXHASH) {
+ hash_type = (rd->rrd5 >> EDMA_HASH_TYPE_SHIFT);
+ if ((hash_type > EDMA_HASH_TYPE_START) && (hash_type < EDMA_HASH_TYPE_END))
+ skb_set_hash(skb, rd->rrd2, PKT_HASH_TYPE_L4);
+ }
+
+#ifdef CONFIG_NF_FLOW_COOKIE
+ skb->flow_cookie = rd->rrd3 & EDMA_RRD_FLOW_COOKIE_MASK;
+#endif
+ edma_receive_checksum(rd, skb);
+
+ /* Process VLAN HW acceleration indication provided by HW */
+ if (unlikely(adapter->default_vlan_tag != rd->rrd4)) {
+ vlan = rd->rrd4;
+ if (likely(rd->rrd7 & EDMA_RRD_CVLAN))
+ __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), vlan);
+ else if (rd->rrd1 & EDMA_RRD_SVLAN)
+ __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021AD), vlan);
+ }
+
+ /* Update rx statistics */
+ adapter->stats.rx_packets++;
+ adapter->stats.rx_bytes += length;
+
+ /* Check if we reached refill threshold */
+ if (cleaned_count >= EDMA_RX_BUFFER_WRITE) {
+ ret_count = edma_alloc_rx_buf(edma_cinfo, erdr, cleaned_count, queue_id);
+ edma_write_reg(EDMA_REG_RX_SW_CONS_IDX_Q(queue_id),
+ sw_next_to_clean);
+ cleaned_count = ret_count;
+ erdr->pending_fill = ret_count;
+ }
+
+ /* At this point skb should go to stack */
+ napi_gro_receive(napi, skb);
+ }
+
+ /* Check if we still have NAPI budget */
+ if (!work_to_do)
+ break;
+
+ /* Read index once again since we still have NAPI budget */
+ edma_read_reg(EDMA_REG_RFD_IDX_Q(queue_id), &data);
+ hw_next_to_clean = (data >> EDMA_RFD_CONS_IDX_SHIFT) &
+ EDMA_RFD_CONS_IDX_MASK;
+ } while (hw_next_to_clean != sw_next_to_clean);
+
+ erdr->sw_next_to_clean = sw_next_to_clean;
+
+ /* Refill here in case refill threshold wasn't reached */
+ if (likely(cleaned_count)) {
+ ret_count = edma_alloc_rx_buf(edma_cinfo, erdr, cleaned_count, queue_id);
+ erdr->pending_fill = ret_count;
+ if (ret_count) {
+ if (net_ratelimit())
+ dev_dbg(&pdev->dev, "Not all buffers was reallocated");
+ }
+
+ edma_write_reg(EDMA_REG_RX_SW_CONS_IDX_Q(queue_id),
+ erdr->sw_next_to_clean);
+ }
+
+ return erdr->pending_fill;
+}
+
+/* edma_delete_rfs_filter()
+ * Remove RFS filter from switch
+ */
+static int edma_delete_rfs_filter(struct edma_adapter *adapter,
+ struct edma_rfs_filter_node *filter_node)
+{
+ int res = -1;
+
+ struct flow_keys *keys = &filter_node->keys;
+
+ if (likely(adapter->set_rfs_rule))
+ res = (*adapter->set_rfs_rule)(adapter->netdev,
+ flow_get_u32_src(keys), flow_get_u32_dst(keys),
+ keys->ports.src, keys->ports.dst,
+ keys->basic.ip_proto, filter_node->rq_id, 0);
+
+ return res;
+}
+
+/* edma_add_rfs_filter()
+ * Add RFS filter to switch
+ */
+static int edma_add_rfs_filter(struct edma_adapter *adapter,
+ struct flow_keys *keys, u16 rq,
+ struct edma_rfs_filter_node *filter_node)
+{
+ int res = -1;
+
+ struct flow_keys *dest_keys = &filter_node->keys;
+
+ memcpy(dest_keys, &filter_node->keys, sizeof(*dest_keys));
+/*
+ dest_keys->control = keys->control;
+ dest_keys->basic = keys->basic;
+ dest_keys->addrs = keys->addrs;
+ dest_keys->ports = keys->ports;
+ dest_keys.ip_proto = keys->ip_proto;
+*/
+ /* Call callback registered by ESS driver */
+ if (likely(adapter->set_rfs_rule))
+ res = (*adapter->set_rfs_rule)(adapter->netdev, flow_get_u32_src(keys),
+ flow_get_u32_dst(keys), keys->ports.src, keys->ports.dst,
+ keys->basic.ip_proto, rq, 1);
+
+ return res;
+}
+
+/* edma_rfs_key_search()
+ * Look for existing RFS entry
+ */
+static struct edma_rfs_filter_node *edma_rfs_key_search(struct hlist_head *h,
+ struct flow_keys *key)
+{
+ struct edma_rfs_filter_node *p;
+
+ hlist_for_each_entry(p, h, node)
+ if (flow_get_u32_src(&p->keys) == flow_get_u32_src(key) &&
+ flow_get_u32_dst(&p->keys) == flow_get_u32_dst(key) &&
+ p->keys.ports.src == key->ports.src &&
+ p->keys.ports.dst == key->ports.dst &&
+ p->keys.basic.ip_proto == key->basic.ip_proto)
+ return p;
+ return NULL;
+}
+
+/* edma_initialise_rfs_flow_table()
+ * Initialise EDMA RFS flow table
+ */
+static void edma_initialise_rfs_flow_table(struct edma_adapter *adapter)
+{
+ int i;
+
+ spin_lock_init(&adapter->rfs.rfs_ftab_lock);
+
+ /* Initialize EDMA flow hash table */
+ for (i = 0; i < EDMA_RFS_FLOW_ENTRIES; i++)
+ INIT_HLIST_HEAD(&adapter->rfs.hlist_head[i]);
+
+ adapter->rfs.max_num_filter = EDMA_RFS_FLOW_ENTRIES;
+ adapter->rfs.filter_available = adapter->rfs.max_num_filter;
+ adapter->rfs.hashtoclean = 0;
+
+ /* Add timer to get periodic RFS updates from OS */
+ timer_setup(&adapter->rfs.expire_rfs, edma_flow_may_expire, 0);
+ mod_timer(&adapter->rfs.expire_rfs, jiffies + HZ / 4);
+}
+
+/* edma_free_rfs_flow_table()
+ * Free EDMA RFS flow table
+ */
+static void edma_free_rfs_flow_table(struct edma_adapter *adapter)
+{
+ int i;
+
+ /* Remove sync timer */
+ del_timer_sync(&adapter->rfs.expire_rfs);
+ spin_lock_bh(&adapter->rfs.rfs_ftab_lock);
+
+ /* Free EDMA RFS table entries */
+ adapter->rfs.filter_available = 0;
+
+ /* Clean-up EDMA flow hash table */
+ for (i = 0; i < EDMA_RFS_FLOW_ENTRIES; i++) {
+ struct hlist_head *hhead;
+ struct hlist_node *tmp;
+ struct edma_rfs_filter_node *filter_node;
+ int res;
+
+ hhead = &adapter->rfs.hlist_head[i];
+ hlist_for_each_entry_safe(filter_node, tmp, hhead, node) {
+ res = edma_delete_rfs_filter(adapter, filter_node);
+ if (res < 0)
+ dev_warn(&adapter->netdev->dev,
+ "EDMA going down but RFS entry %d not allowed to be flushed by Switch",
+ filter_node->flow_id);
+ hlist_del(&filter_node->node);
+ kfree(filter_node);
+ }
+ }
+ spin_unlock_bh(&adapter->rfs.rfs_ftab_lock);
+}
+
+/* edma_tx_unmap_and_free()
+ * clean TX buffer
+ */
+static inline void edma_tx_unmap_and_free(struct platform_device *pdev,
+ struct edma_sw_desc *sw_desc)
+{
+ struct sk_buff *skb = sw_desc->skb;
+
+ if (likely((sw_desc->flags & EDMA_SW_DESC_FLAG_SKB_HEAD) ||
+ (sw_desc->flags & EDMA_SW_DESC_FLAG_SKB_FRAGLIST)))
+ /* unmap_single for skb head area */
+ dma_unmap_single(&pdev->dev, sw_desc->dma,
+ sw_desc->length, DMA_TO_DEVICE);
+ else if (sw_desc->flags & EDMA_SW_DESC_FLAG_SKB_FRAG)
+ /* unmap page for paged fragments */
+ dma_unmap_page(&pdev->dev, sw_desc->dma,
+ sw_desc->length, DMA_TO_DEVICE);
+
+ if (likely(sw_desc->flags & EDMA_SW_DESC_FLAG_LAST))
+ dev_kfree_skb_any(skb);
+
+ sw_desc->flags = 0;
+}
+
+/* edma_tx_complete()
+ * Used to clean tx queues and update hardware and consumer index
+ */
+static void edma_tx_complete(struct edma_common_info *edma_cinfo, int queue_id)
+{
+ struct edma_tx_desc_ring *etdr = edma_cinfo->tpd_ring[queue_id];
+ struct edma_sw_desc *sw_desc;
+ struct platform_device *pdev = edma_cinfo->pdev;
+ int i;
+
+ u16 sw_next_to_clean = etdr->sw_next_to_clean;
+ u16 hw_next_to_clean;
+ u32 data = 0;
+
+ edma_read_reg(EDMA_REG_TPD_IDX_Q(queue_id), &data);
+ hw_next_to_clean = (data >> EDMA_TPD_CONS_IDX_SHIFT) & EDMA_TPD_CONS_IDX_MASK;
+
+ /* clean the buffer here */
+ while (sw_next_to_clean != hw_next_to_clean) {
+ sw_desc = &etdr->sw_desc[sw_next_to_clean];
+ edma_tx_unmap_and_free(pdev, sw_desc);
+ sw_next_to_clean = (sw_next_to_clean + 1) & (etdr->count - 1);
+ }
+
+ etdr->sw_next_to_clean = sw_next_to_clean;
+
+ /* update the TPD consumer index register */
+ edma_write_reg(EDMA_REG_TX_SW_CONS_IDX_Q(queue_id), sw_next_to_clean);
+
+ /* Wake the queue if queue is stopped and netdev link is up */
+ for (i = 0; i < EDMA_MAX_NETDEV_PER_QUEUE && etdr->nq[i] ; i++) {
+ if (netif_tx_queue_stopped(etdr->nq[i])) {
+ if ((etdr->netdev[i]) && netif_carrier_ok(etdr->netdev[i]))
+ netif_tx_wake_queue(etdr->nq[i]);
+ }
+ }
+}
+
+/* edma_get_tx_buffer()
+ * Get sw_desc corresponding to the TPD
+ */
+static struct edma_sw_desc *edma_get_tx_buffer(struct edma_common_info *edma_cinfo,
+ struct edma_tx_desc *tpd, int queue_id)
+{
+ struct edma_tx_desc_ring *etdr = edma_cinfo->tpd_ring[queue_id];
+ return &etdr->sw_desc[tpd - (struct edma_tx_desc *)etdr->hw_desc];
+}
+
+/* edma_get_next_tpd()
+ * Return a TPD descriptor for transfer
+ */
+static struct edma_tx_desc *edma_get_next_tpd(struct edma_common_info *edma_cinfo,
+ int queue_id)
+{
+ struct edma_tx_desc_ring *etdr = edma_cinfo->tpd_ring[queue_id];
+ u16 sw_next_to_fill = etdr->sw_next_to_fill;
+ struct edma_tx_desc *tpd_desc =
+ (&((struct edma_tx_desc *)(etdr->hw_desc))[sw_next_to_fill]);
+
+ etdr->sw_next_to_fill = (etdr->sw_next_to_fill + 1) & (etdr->count - 1);
+
+ return tpd_desc;
+}
+
+/* edma_tpd_available()
+ * Check number of free TPDs
+ */
+static inline u16 edma_tpd_available(struct edma_common_info *edma_cinfo,
+ int queue_id)
+{
+ struct edma_tx_desc_ring *etdr = edma_cinfo->tpd_ring[queue_id];
+
+ u16 sw_next_to_fill;
+ u16 sw_next_to_clean;
+ u16 count = 0;
+
+ sw_next_to_clean = etdr->sw_next_to_clean;
+ sw_next_to_fill = etdr->sw_next_to_fill;
+
+ if (likely(sw_next_to_clean <= sw_next_to_fill))
+ count = etdr->count;
+
+ return count + sw_next_to_clean - sw_next_to_fill - 1;
+}
+
+/* edma_tx_queue_get()
+ * Get the starting number of the queue
+ */
+static inline int edma_tx_queue_get(struct edma_adapter *adapter,
+ struct sk_buff *skb, int txq_id)
+{
+ /* skb->priority is used as an index to skb priority table
+ * and based on packet priority, correspong queue is assigned.
+ */
+ return adapter->tx_start_offset[txq_id] + edma_skb_priority_offset(skb);
+}
+
+/* edma_tx_update_hw_idx()
+ * update the producer index for the ring transmitted
+ */
+static void edma_tx_update_hw_idx(struct edma_common_info *edma_cinfo,
+ struct sk_buff *skb, int queue_id)
+{
+ struct edma_tx_desc_ring *etdr = edma_cinfo->tpd_ring[queue_id];
+ u32 tpd_idx_data;
+
+ /* Read and update the producer index */
+ edma_read_reg(EDMA_REG_TPD_IDX_Q(queue_id), &tpd_idx_data);
+ tpd_idx_data &= ~EDMA_TPD_PROD_IDX_BITS;
+ tpd_idx_data |= (etdr->sw_next_to_fill & EDMA_TPD_PROD_IDX_MASK)
+ << EDMA_TPD_PROD_IDX_SHIFT;
+
+ edma_write_reg(EDMA_REG_TPD_IDX_Q(queue_id), tpd_idx_data);
+}
+
+/* edma_rollback_tx()
+ * Function to retrieve tx resources in case of error
+ */
+static void edma_rollback_tx(struct edma_adapter *adapter,
+ struct edma_tx_desc *start_tpd, int queue_id)
+{
+ struct edma_tx_desc_ring *etdr = adapter->edma_cinfo->tpd_ring[queue_id];
+ struct edma_sw_desc *sw_desc;
+ struct edma_tx_desc *tpd = NULL;
+ u16 start_index, index;
+
+ start_index = start_tpd - (struct edma_tx_desc *)(etdr->hw_desc);
+
+ index = start_index;
+ while (index != etdr->sw_next_to_fill) {
+ tpd = (&((struct edma_tx_desc *)(etdr->hw_desc))[index]);
+ sw_desc = &etdr->sw_desc[index];
+ edma_tx_unmap_and_free(adapter->pdev, sw_desc);
+ memset(tpd, 0, sizeof(struct edma_tx_desc));
+ if (++index == etdr->count)
+ index = 0;
+ }
+ etdr->sw_next_to_fill = start_index;
+}
+
+/* edma_tx_map_and_fill()
+ * gets called from edma_xmit_frame
+ *
+ * This is where the dma of the buffer to be transmitted
+ * gets mapped
+ */
+static int edma_tx_map_and_fill(struct edma_common_info *edma_cinfo,
+ struct edma_adapter *adapter, struct sk_buff *skb, int queue_id,
+ unsigned int flags_transmit, u16 from_cpu, u16 dp_bitmap,
+ bool packet_is_rstp, int nr_frags)
+{
+ struct edma_sw_desc *sw_desc = NULL;
+ struct platform_device *pdev = edma_cinfo->pdev;
+ struct edma_tx_desc *tpd = NULL, *start_tpd = NULL;
+ struct sk_buff *iter_skb;
+ int i = 0;
+ u32 word1 = 0, word3 = 0, lso_word1 = 0, svlan_tag = 0;
+ u16 buf_len, lso_desc_len = 0;
+
+ /* It should either be a nr_frags skb or fraglist skb but not both */
+ BUG_ON(nr_frags && skb_has_frag_list(skb));
+
+ if (skb_is_gso(skb)) {
+ /* TODO: What additional checks need to be performed here */
+ if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV4) {
+ lso_word1 |= EDMA_TPD_IPV4_EN;
+ ip_hdr(skb)->check = 0;
+ tcp_hdr(skb)->check = ~csum_tcpudp_magic(ip_hdr(skb)->saddr,
+ ip_hdr(skb)->daddr, 0, IPPROTO_TCP, 0);
+ } else if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV6) {
+ lso_word1 |= EDMA_TPD_LSO_V2_EN;
+ ipv6_hdr(skb)->payload_len = 0;
+ tcp_hdr(skb)->check = ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr,
+ &ipv6_hdr(skb)->daddr, 0, IPPROTO_TCP, 0);
+ } else
+ return -EINVAL;
+
+ lso_word1 |= EDMA_TPD_LSO_EN | ((skb_shinfo(skb)->gso_size & EDMA_TPD_MSS_MASK) << EDMA_TPD_MSS_SHIFT) |
+ (skb_transport_offset(skb) << EDMA_TPD_HDR_SHIFT);
+ } else if (flags_transmit & EDMA_HW_CHECKSUM) {
+ u8 css, cso;
+ cso = skb_checksum_start_offset(skb);
+ css = cso + skb->csum_offset;
+
+ word1 |= (EDMA_TPD_CUSTOM_CSUM_EN);
+ word1 |= (cso >> 1) << EDMA_TPD_HDR_SHIFT;
+ word1 |= ((css >> 1) << EDMA_TPD_CUSTOM_CSUM_SHIFT);
+ }
+
+ if (skb->protocol == htons(ETH_P_PPP_SES))
+ word1 |= EDMA_TPD_PPPOE_EN;
+
+ if (flags_transmit & EDMA_VLAN_TX_TAG_INSERT_FLAG) {
+ switch(skb->vlan_proto) {
+ case htons(ETH_P_8021Q):
+ word3 |= (1 << EDMA_TX_INS_CVLAN);
+ word3 |= skb_vlan_tag_get(skb) << EDMA_TX_CVLAN_TAG_SHIFT;
+ break;
+ case htons(ETH_P_8021AD):
+ word1 |= (1 << EDMA_TX_INS_SVLAN);
+ svlan_tag = skb_vlan_tag_get(skb) << EDMA_TX_SVLAN_TAG_SHIFT;
+ break;
+ default:
+ dev_err(&pdev->dev, "no ctag or stag present\n");
+ goto vlan_tag_error;
+ }
+ } else if (flags_transmit & EDMA_VLAN_TX_TAG_INSERT_DEFAULT_FLAG) {
+ word3 |= (1 << EDMA_TX_INS_CVLAN);
+ word3 |= (adapter->default_vlan_tag) << EDMA_TX_CVLAN_TAG_SHIFT;
+ }
+
+ if (packet_is_rstp) {
+ word3 |= dp_bitmap << EDMA_TPD_PORT_BITMAP_SHIFT;
+ word3 |= from_cpu << EDMA_TPD_FROM_CPU_SHIFT;
+ } else {
+ word3 |= adapter->dp_bitmap << EDMA_TPD_PORT_BITMAP_SHIFT;
+ }
+
+ buf_len = skb_headlen(skb);
+
+ if (lso_word1) {
+ if (lso_word1 & EDMA_TPD_LSO_V2_EN) {
+
+ /* IPv6 LSOv2 descriptor */
+ start_tpd = tpd = edma_get_next_tpd(edma_cinfo, queue_id);
+ sw_desc = edma_get_tx_buffer(edma_cinfo, tpd, queue_id);
+ sw_desc->flags |= EDMA_SW_DESC_FLAG_SKB_NONE;
+
+ /* LSOv2 descriptor overrides addr field to pass length */
+ tpd->addr = cpu_to_le16(skb->len);
+ tpd->svlan_tag = svlan_tag;
+ tpd->word1 = word1 | lso_word1;
+ tpd->word3 = word3;
+ }
+
+ tpd = edma_get_next_tpd(edma_cinfo, queue_id);
+ if (!start_tpd)
+ start_tpd = tpd;
+ sw_desc = edma_get_tx_buffer(edma_cinfo, tpd, queue_id);
+
+ /* The last buffer info contain the skb address,
+ * so skb will be freed after unmap
+ */
+ sw_desc->length = lso_desc_len;
+ sw_desc->flags |= EDMA_SW_DESC_FLAG_SKB_HEAD;
+
+ sw_desc->dma = dma_map_single(&adapter->pdev->dev,
+ skb->data, buf_len, DMA_TO_DEVICE);
+ if (dma_mapping_error(&pdev->dev, sw_desc->dma))
+ goto dma_error;
+
+ tpd->addr = cpu_to_le32(sw_desc->dma);
+ tpd->len = cpu_to_le16(buf_len);
+
+ tpd->svlan_tag = svlan_tag;
+ tpd->word1 = word1 | lso_word1;
+ tpd->word3 = word3;
+
+ /* The last buffer info contain the skb address,
+ * so it will be freed after unmap
+ */
+ sw_desc->length = lso_desc_len;
+ sw_desc->flags |= EDMA_SW_DESC_FLAG_SKB_HEAD;
+
+ buf_len = 0;
+ }
+
+ if (likely(buf_len)) {
+
+ /* TODO Do not dequeue descriptor if there is a potential error */
+ tpd = edma_get_next_tpd(edma_cinfo, queue_id);
+
+ if (!start_tpd)
+ start_tpd = tpd;
+
+ sw_desc = edma_get_tx_buffer(edma_cinfo, tpd, queue_id);
+
+ /* The last buffer info contain the skb address,
+ * so it will be free after unmap
+ */
+ sw_desc->length = buf_len;
+ sw_desc->flags |= EDMA_SW_DESC_FLAG_SKB_HEAD;
+ sw_desc->dma = dma_map_single(&adapter->pdev->dev,
+ skb->data, buf_len, DMA_TO_DEVICE);
+ if (dma_mapping_error(&pdev->dev, sw_desc->dma))
+ goto dma_error;
+
+ tpd->addr = cpu_to_le32(sw_desc->dma);
+ tpd->len = cpu_to_le16(buf_len);
+
+ tpd->svlan_tag = svlan_tag;
+ tpd->word1 = word1 | lso_word1;
+ tpd->word3 = word3;
+ }
+
+ /* Walk through all paged fragments */
+ while (nr_frags--) {
+ skb_frag_t *frag = &skb_shinfo(skb)->frags[i];
+ buf_len = skb_frag_size(frag);
+ tpd = edma_get_next_tpd(edma_cinfo, queue_id);
+ sw_desc = edma_get_tx_buffer(edma_cinfo, tpd, queue_id);
+ sw_desc->length = buf_len;
+ sw_desc->flags |= EDMA_SW_DESC_FLAG_SKB_FRAG;
+
+ sw_desc->dma = skb_frag_dma_map(&pdev->dev, frag, 0, buf_len, DMA_TO_DEVICE);
+
+ if (dma_mapping_error(NULL, sw_desc->dma))
+ goto dma_error;
+
+ tpd->addr = cpu_to_le32(sw_desc->dma);
+ tpd->len = cpu_to_le16(buf_len);
+
+ tpd->svlan_tag = svlan_tag;
+ tpd->word1 = word1 | lso_word1;
+ tpd->word3 = word3;
+ i++;
+ }
+
+ /* Walk through all fraglist skbs */
+ skb_walk_frags(skb, iter_skb) {
+ buf_len = iter_skb->len;
+ tpd = edma_get_next_tpd(edma_cinfo, queue_id);
+ sw_desc = edma_get_tx_buffer(edma_cinfo, tpd, queue_id);
+ sw_desc->length = buf_len;
+ sw_desc->dma = dma_map_single(&adapter->pdev->dev,
+ iter_skb->data, buf_len, DMA_TO_DEVICE);
+
+ if (dma_mapping_error(NULL, sw_desc->dma))
+ goto dma_error;
+
+ tpd->addr = cpu_to_le32(sw_desc->dma);
+ tpd->len = cpu_to_le16(buf_len);
+ tpd->svlan_tag = svlan_tag;
+ tpd->word1 = word1 | lso_word1;
+ tpd->word3 = word3;
+ sw_desc->flags |= EDMA_SW_DESC_FLAG_SKB_FRAGLIST;
+ }
+
+ if (tpd)
+ tpd->word1 |= 1 << EDMA_TPD_EOP_SHIFT;
+
+ sw_desc->skb = skb;
+ sw_desc->flags |= EDMA_SW_DESC_FLAG_LAST;
+
+ return 0;
+
+dma_error:
+ edma_rollback_tx(adapter, start_tpd, queue_id);
+ dev_err(&pdev->dev, "TX DMA map failed\n");
+vlan_tag_error:
+ return -ENOMEM;
+}
+
+/* edma_check_link()
+ * check Link status
+ */
+static int edma_check_link(struct edma_adapter *adapter)
+{
+ struct phy_device *phydev = adapter->phydev;
+
+ if (!(adapter->poll_required))
+ return __EDMA_LINKUP;
+
+ if (phydev->link)
+ return __EDMA_LINKUP;
+
+ return __EDMA_LINKDOWN;
+}
+
+/* edma_adjust_link()
+ * check for edma link status
+ */
+void edma_adjust_link(struct net_device *netdev)
+{
+ int status;
+ struct edma_adapter *adapter = netdev_priv(netdev);
+ struct phy_device *phydev = adapter->phydev;
+
+ if (!test_bit(__EDMA_UP, &adapter->state_flags))
+ return;
+
+ status = edma_check_link(adapter);
+
+ if (status == __EDMA_LINKUP && adapter->link_state == __EDMA_LINKDOWN) {
+ dev_info(&adapter->pdev->dev, "%s: GMAC Link is up with phy_speed=%d\n", netdev->name, phydev->speed);
+ adapter->link_state = __EDMA_LINKUP;
+ if (adapter->edma_cinfo->is_single_phy) {
+ ess_set_port_status_speed(adapter->edma_cinfo, phydev,
+ ffs(adapter->dp_bitmap) - 1);
+ }
+ netif_carrier_on(netdev);
+ if (netif_running(netdev))
+ netif_tx_wake_all_queues(netdev);
+ } else if (status == __EDMA_LINKDOWN && adapter->link_state == __EDMA_LINKUP) {
+ dev_info(&adapter->pdev->dev, "%s: GMAC Link is down\n", netdev->name);
+ adapter->link_state = __EDMA_LINKDOWN;
+ netif_carrier_off(netdev);
+ netif_tx_stop_all_queues(netdev);
+ }
+}
+
+/* edma_get_stats()
+ * Statistics api used to retreive the tx/rx statistics
+ */
+struct net_device_stats *edma_get_stats(struct net_device *netdev)
+{
+ struct edma_adapter *adapter = netdev_priv(netdev);
+
+ return &adapter->stats;
+}
+
+/* edma_xmit()
+ * Main api to be called by the core for packet transmission
+ */
+netdev_tx_t edma_xmit(struct sk_buff *skb,
+ struct net_device *net_dev)
+{
+ struct edma_adapter *adapter = netdev_priv(net_dev);
+ struct edma_common_info *edma_cinfo = adapter->edma_cinfo;
+ struct edma_tx_desc_ring *etdr;
+ u16 from_cpu, dp_bitmap, txq_id;
+ int ret, nr_frags = 0, num_tpds_needed = 1, queue_id;
+ unsigned int flags_transmit = 0;
+ bool packet_is_rstp = false;
+ struct netdev_queue *nq = NULL;
+
+ if (skb_shinfo(skb)->nr_frags) {
+ nr_frags = skb_shinfo(skb)->nr_frags;
+ num_tpds_needed += nr_frags;
+ } else if (skb_has_frag_list(skb)) {
+ struct sk_buff *iter_skb;
+
+ skb_walk_frags(skb, iter_skb)
+ num_tpds_needed++;
+ }
+
+ if (num_tpds_needed > EDMA_MAX_SKB_FRAGS) {
+ dev_err(&net_dev->dev,
+ "skb received with fragments %d which is more than %lu",
+ num_tpds_needed, EDMA_MAX_SKB_FRAGS);
+ dev_kfree_skb_any(skb);
+ adapter->stats.tx_errors++;
+ return NETDEV_TX_OK;
+ }
+
+ if (edma_stp_rstp) {
+ u16 ath_hdr, ath_eth_type;
+ u8 mac_addr[EDMA_ETH_HDR_LEN];
+ ath_eth_type = ntohs(*(uint16_t *)&skb->data[12]);
+ if (ath_eth_type == edma_ath_eth_type) {
+ packet_is_rstp = true;
+ ath_hdr = htons(*(uint16_t *)&skb->data[14]);
+ dp_bitmap = ath_hdr & EDMA_TX_ATH_HDR_PORT_BITMAP_MASK;
+ from_cpu = (ath_hdr & EDMA_TX_ATH_HDR_FROM_CPU_MASK) >> EDMA_TX_ATH_HDR_FROM_CPU_SHIFT;
+ memcpy(mac_addr, skb->data, EDMA_ETH_HDR_LEN);
+
+ skb_pull(skb, 4);
+
+ memcpy(skb->data, mac_addr, EDMA_ETH_HDR_LEN);
+ }
+ }
+
+ /* this will be one of the 4 TX queues exposed to linux kernel */
+ txq_id = skb_get_queue_mapping(skb);
+ queue_id = edma_tx_queue_get(adapter, skb, txq_id);
+ etdr = edma_cinfo->tpd_ring[queue_id];
+ nq = netdev_get_tx_queue(net_dev, txq_id);
+
+ local_bh_disable();
+ /* Tx is not handled in bottom half context. Hence, we need to protect
+ * Tx from tasks and bottom half
+ */
+
+ if (num_tpds_needed > edma_tpd_available(edma_cinfo, queue_id)) {
+ /* not enough descriptor, just stop queue */
+ netif_tx_stop_queue(nq);
+ local_bh_enable();
+ dev_dbg(&net_dev->dev, "Not enough descriptors available");
+ edma_cinfo->edma_ethstats.tx_desc_error++;
+ return NETDEV_TX_BUSY;
+ }
+
+ /* Check and mark VLAN tag offload */
+ if (!adapter->edma_cinfo->is_single_phy) {
+ if (unlikely(skb_vlan_tag_present(skb)))
+ flags_transmit |= EDMA_VLAN_TX_TAG_INSERT_FLAG;
+ else if (adapter->default_vlan_tag)
+ flags_transmit |= EDMA_VLAN_TX_TAG_INSERT_DEFAULT_FLAG;
+ }
+
+ /* Check and mark checksum offload */
+ if (likely(skb->ip_summed == CHECKSUM_PARTIAL))
+ flags_transmit |= EDMA_HW_CHECKSUM;
+
+ /* Map and fill descriptor for Tx */
+ ret = edma_tx_map_and_fill(edma_cinfo, adapter, skb, queue_id,
+ flags_transmit, from_cpu, dp_bitmap, packet_is_rstp, nr_frags);
+ if (ret) {
+ dev_kfree_skb_any(skb);
+ adapter->stats.tx_errors++;
+ goto netdev_okay;
+ }
+
+ /* Update SW producer index */
+ edma_tx_update_hw_idx(edma_cinfo, skb, queue_id);
+
+ /* update tx statistics */
+ adapter->stats.tx_packets++;
+ adapter->stats.tx_bytes += skb->len;
+
+netdev_okay:
+ local_bh_enable();
+ return NETDEV_TX_OK;
+}
+
+/*
+ * edma_flow_may_expire()
+ * Timer function called periodically to delete the node
+ */
+void edma_flow_may_expire(struct timer_list *t)
+{
+ struct edma_rfs_flow_table *table = from_timer(table, t, expire_rfs);
+ struct edma_adapter *adapter =
+ container_of(table, typeof(*adapter), rfs);
+ int j;
+
+ spin_lock_bh(&adapter->rfs.rfs_ftab_lock);
+ for (j = 0; j < EDMA_RFS_EXPIRE_COUNT_PER_CALL; j++) {
+ struct hlist_head *hhead;
+ struct hlist_node *tmp;
+ struct edma_rfs_filter_node *n;
+ bool res;
+
+ hhead = &adapter->rfs.hlist_head[adapter->rfs.hashtoclean++];
+ hlist_for_each_entry_safe(n, tmp, hhead, node) {
+ res = rps_may_expire_flow(adapter->netdev, n->rq_id,
+ n->flow_id, n->filter_id);
+ if (res) {
+ int ret;
+ ret = edma_delete_rfs_filter(adapter, n);
+ if (ret < 0)
+ dev_dbg(&adapter->netdev->dev,
+ "RFS entry %d not allowed to be flushed by Switch",
+ n->flow_id);
+ else {
+ hlist_del(&n->node);
+ kfree(n);
+ adapter->rfs.filter_available++;
+ }
+ }
+ }
+ }
+
+ adapter->rfs.hashtoclean = adapter->rfs.hashtoclean & (EDMA_RFS_FLOW_ENTRIES - 1);
+ spin_unlock_bh(&adapter->rfs.rfs_ftab_lock);
+ mod_timer(&adapter->rfs.expire_rfs, jiffies + HZ / 4);
+}
+
+/* edma_rx_flow_steer()
+ * Called by core to to steer the flow to CPU
+ */
+int edma_rx_flow_steer(struct net_device *dev, const struct sk_buff *skb,
+ u16 rxq, u32 flow_id)
+{
+ struct flow_keys keys;
+ struct edma_rfs_filter_node *filter_node;
+ struct edma_adapter *adapter = netdev_priv(dev);
+ u16 hash_tblid;
+ int res;
+
+ if (skb->protocol == htons(ETH_P_IPV6)) {
+ dev_err(&adapter->pdev->dev, "IPv6 not supported\n");
+ res = -EINVAL;
+ goto no_protocol_err;
+ }
+
+ /* Dissect flow parameters
+ * We only support IPv4 + TCP/UDP
+ */
+ res = skb_flow_dissect_flow_keys(skb, &keys, 0);
+ if (!((keys.basic.ip_proto == IPPROTO_TCP) || (keys.basic.ip_proto == IPPROTO_UDP))) {
+ res = -EPROTONOSUPPORT;
+ goto no_protocol_err;
+ }
+
+ /* Check if table entry exists */
+ hash_tblid = skb_get_hash_raw(skb) & EDMA_RFS_FLOW_ENTRIES_MASK;
+
+ spin_lock_bh(&adapter->rfs.rfs_ftab_lock);
+ filter_node = edma_rfs_key_search(&adapter->rfs.hlist_head[hash_tblid], &keys);
+
+ if (filter_node) {
+ if (rxq == filter_node->rq_id) {
+ res = -EEXIST;
+ goto out;
+ } else {
+ res = edma_delete_rfs_filter(adapter, filter_node);
+ if (res < 0)
+ dev_warn(&adapter->netdev->dev,
+ "Cannot steer flow %d to different queue",
+ filter_node->flow_id);
+ else {
+ adapter->rfs.filter_available++;
+ res = edma_add_rfs_filter(adapter, &keys, rxq, filter_node);
+ if (res < 0) {
+ dev_warn(&adapter->netdev->dev,
+ "Cannot steer flow %d to different queue",
+ filter_node->flow_id);
+ } else {
+ adapter->rfs.filter_available--;
+ filter_node->rq_id = rxq;
+ filter_node->filter_id = res;
+ }
+ }
+ }
+ } else {
+ if (adapter->rfs.filter_available == 0) {
+ res = -EBUSY;
+ goto out;
+ }
+
+ filter_node = kmalloc(sizeof(*filter_node), GFP_ATOMIC);
+ if (!filter_node) {
+ res = -ENOMEM;
+ goto out;
+ }
+
+ res = edma_add_rfs_filter(adapter, &keys, rxq, filter_node);
+ if (res < 0) {
+ kfree(filter_node);
+ goto out;
+ }
+
+ adapter->rfs.filter_available--;
+ filter_node->rq_id = rxq;
+ filter_node->filter_id = res;
+ filter_node->flow_id = flow_id;
+ filter_node->keys = keys;
+ INIT_HLIST_NODE(&filter_node->node);
+ hlist_add_head(&filter_node->node, &adapter->rfs.hlist_head[hash_tblid]);
+ }
+
+out:
+ spin_unlock_bh(&adapter->rfs.rfs_ftab_lock);
+no_protocol_err:
+ return res;
+}
+
+/* edma_register_rfs_filter()
+ * Add RFS filter callback
+ */
+int edma_register_rfs_filter(struct net_device *netdev,
+ set_rfs_filter_callback_t set_filter)
+{
+ struct edma_adapter *adapter = netdev_priv(netdev);
+
+ spin_lock_bh(&adapter->rfs.rfs_ftab_lock);
+
+ if (adapter->set_rfs_rule) {
+ spin_unlock_bh(&adapter->rfs.rfs_ftab_lock);
+ return -1;
+ }
+
+ adapter->set_rfs_rule = set_filter;
+ spin_unlock_bh(&adapter->rfs.rfs_ftab_lock);
+
+ return 0;
+}
+
+/* edma_alloc_tx_rings()
+ * Allocate rx rings
+ */
+int edma_alloc_tx_rings(struct edma_common_info *edma_cinfo)
+{
+ struct platform_device *pdev = edma_cinfo->pdev;
+ int i, err = 0;
+
+ for (i = 0; i < edma_cinfo->num_tx_queues; i++) {
+ err = edma_alloc_tx_ring(edma_cinfo, edma_cinfo->tpd_ring[i]);
+ if (err) {
+ dev_err(&pdev->dev, "Tx Queue alloc %u failed\n", i);
+ return err;
+ }
+ }
+
+ return 0;
+}
+
+/* edma_free_tx_rings()
+ * Free tx rings
+ */
+void edma_free_tx_rings(struct edma_common_info *edma_cinfo)
+{
+ int i;
+
+ for (i = 0; i < edma_cinfo->num_tx_queues; i++)
+ edma_free_tx_ring(edma_cinfo, edma_cinfo->tpd_ring[i]);
+}
+
+/* edma_free_tx_resources()
+ * Free buffers associated with tx rings
+ */
+void edma_free_tx_resources(struct edma_common_info *edma_cinfo)
+{
+ struct edma_tx_desc_ring *etdr;
+ struct edma_sw_desc *sw_desc;
+ struct platform_device *pdev = edma_cinfo->pdev;
+ int i, j;
+
+ for (i = 0; i < edma_cinfo->num_tx_queues; i++) {
+ etdr = edma_cinfo->tpd_ring[i];
+ for (j = 0; j < EDMA_TX_RING_SIZE; j++) {
+ sw_desc = &etdr->sw_desc[j];
+ if (sw_desc->flags & (EDMA_SW_DESC_FLAG_SKB_HEAD |
+ EDMA_SW_DESC_FLAG_SKB_FRAG | EDMA_SW_DESC_FLAG_SKB_FRAGLIST))
+ edma_tx_unmap_and_free(pdev, sw_desc);
+ }
+ }
+}
+
+/* edma_alloc_rx_rings()
+ * Allocate rx rings
+ */
+int edma_alloc_rx_rings(struct edma_common_info *edma_cinfo)
+{
+ struct platform_device *pdev = edma_cinfo->pdev;
+ int i, j, err = 0;
+
+ for (i = 0, j = 0; i < edma_cinfo->num_rx_queues; i++) {
+ err = edma_alloc_rx_ring(edma_cinfo, edma_cinfo->rfd_ring[j]);
+ if (err) {
+ dev_err(&pdev->dev, "Rx Queue alloc%u failed\n", i);
+ return err;
+ }
+ j += ((edma_cinfo->num_rx_queues == 4) ? 2 : 1);
+ }
+
+ return 0;
+}
+
+/* edma_free_rx_rings()
+ * free rx rings
+ */
+void edma_free_rx_rings(struct edma_common_info *edma_cinfo)
+{
+ int i, j;
+
+ for (i = 0, j = 0; i < edma_cinfo->num_rx_queues; i++) {
+ edma_free_rx_ring(edma_cinfo, edma_cinfo->rfd_ring[j]);
+ j += ((edma_cinfo->num_rx_queues == 4) ? 2 : 1);
+ }
+}
+
+/* edma_free_queues()
+ * Free the queues allocaated
+ */
+void edma_free_queues(struct edma_common_info *edma_cinfo)
+{
+ int i , j;
+
+ for (i = 0; i < edma_cinfo->num_tx_queues; i++) {
+ if (edma_cinfo->tpd_ring[i])
+ kfree(edma_cinfo->tpd_ring[i]);
+ edma_cinfo->tpd_ring[i] = NULL;
+ }
+
+ for (i = 0, j = 0; i < edma_cinfo->num_rx_queues; i++) {
+ if (edma_cinfo->rfd_ring[j])
+ kfree(edma_cinfo->rfd_ring[j]);
+ edma_cinfo->rfd_ring[j] = NULL;
+ j += ((edma_cinfo->num_rx_queues == 4) ? 2 : 1);
+ }
+
+ edma_cinfo->num_rx_queues = 0;
+ edma_cinfo->num_tx_queues = 0;
+
+ return;
+}
+
+/* edma_free_rx_resources()
+ * Free buffers associated with tx rings
+ */
+void edma_free_rx_resources(struct edma_common_info *edma_cinfo)
+{
+ struct edma_rfd_desc_ring *erdr;
+ struct edma_sw_desc *sw_desc;
+ struct platform_device *pdev = edma_cinfo->pdev;
+ int i, j, k;
+
+ for (i = 0, k = 0; i < edma_cinfo->num_rx_queues; i++) {
+ erdr = edma_cinfo->rfd_ring[k];
+ for (j = 0; j < EDMA_RX_RING_SIZE; j++) {
+ sw_desc = &erdr->sw_desc[j];
+ if (likely(sw_desc->flags & EDMA_SW_DESC_FLAG_SKB_HEAD)) {
+ dma_unmap_single(&pdev->dev, sw_desc->dma,
+ sw_desc->length, DMA_FROM_DEVICE);
+ edma_clean_rfd(erdr, j);
+ } else if ((sw_desc->flags & EDMA_SW_DESC_FLAG_SKB_FRAG)) {
+ dma_unmap_page(&pdev->dev, sw_desc->dma,
+ sw_desc->length, DMA_FROM_DEVICE);
+ edma_clean_rfd(erdr, j);
+ }
+ }
+ k += ((edma_cinfo->num_rx_queues == 4) ? 2 : 1);
+
+ }
+}
+
+/* edma_alloc_queues_tx()
+ * Allocate memory for all rings
+ */
+int edma_alloc_queues_tx(struct edma_common_info *edma_cinfo)
+{
+ int i;
+
+ for (i = 0; i < edma_cinfo->num_tx_queues; i++) {
+ struct edma_tx_desc_ring *etdr;
+ etdr = kzalloc(sizeof(struct edma_tx_desc_ring), GFP_KERNEL);
+ if (!etdr)
+ goto err;
+ etdr->count = edma_cinfo->tx_ring_count;
+ edma_cinfo->tpd_ring[i] = etdr;
+ }
+
+ return 0;
+err:
+ edma_free_queues(edma_cinfo);
+ return -1;
+}
+
+/* edma_alloc_queues_rx()
+ * Allocate memory for all rings
+ */
+int edma_alloc_queues_rx(struct edma_common_info *edma_cinfo)
+{
+ int i, j;
+
+ for (i = 0, j = 0; i < edma_cinfo->num_rx_queues; i++) {
+ struct edma_rfd_desc_ring *rfd_ring;
+ rfd_ring = kzalloc(sizeof(struct edma_rfd_desc_ring),
+ GFP_KERNEL);
+ if (!rfd_ring)
+ goto err;
+ rfd_ring->count = edma_cinfo->rx_ring_count;
+ edma_cinfo->rfd_ring[j] = rfd_ring;
+ j += ((edma_cinfo->num_rx_queues == 4) ? 2 : 1);
+ }
+ return 0;
+err:
+ edma_free_queues(edma_cinfo);
+ return -1;
+}
+
+/* edma_clear_irq_status()
+ * Clear interrupt status
+ */
+void edma_clear_irq_status()
+{
+ edma_write_reg(EDMA_REG_RX_ISR, 0xff);
+ edma_write_reg(EDMA_REG_TX_ISR, 0xffff);
+ edma_write_reg(EDMA_REG_MISC_ISR, 0x1fff);
+ edma_write_reg(EDMA_REG_WOL_ISR, 0x1);
+};
+
+/* edma_configure()
+ * Configure skb, edma interrupts and control register.
+ */
+int edma_configure(struct edma_common_info *edma_cinfo)
+{
+ struct edma_hw *hw = &edma_cinfo->hw;
+ u32 intr_modrt_data;
+ u32 intr_ctrl_data = 0;
+ int i, j, ret_count;
+
+ edma_read_reg(EDMA_REG_INTR_CTRL, &intr_ctrl_data);
+ intr_ctrl_data &= ~(1 << EDMA_INTR_SW_IDX_W_TYP_SHIFT);
+ intr_ctrl_data |= hw->intr_sw_idx_w << EDMA_INTR_SW_IDX_W_TYP_SHIFT;
+ edma_write_reg(EDMA_REG_INTR_CTRL, intr_ctrl_data);
+
+ edma_clear_irq_status();
+
+ /* Clear any WOL status */
+ edma_write_reg(EDMA_REG_WOL_CTRL, 0);
+ intr_modrt_data = (EDMA_TX_IMT << EDMA_IRQ_MODRT_TX_TIMER_SHIFT);
+ intr_modrt_data |= (EDMA_RX_IMT << EDMA_IRQ_MODRT_RX_TIMER_SHIFT);
+ edma_write_reg(EDMA_REG_IRQ_MODRT_TIMER_INIT, intr_modrt_data);
+ edma_configure_tx(edma_cinfo);
+ edma_configure_rx(edma_cinfo);
+
+ /* Allocate the RX buffer */
+ for (i = 0, j = 0; i < edma_cinfo->num_rx_queues; i++) {
+ struct edma_rfd_desc_ring *ring = edma_cinfo->rfd_ring[j];
+ ret_count = edma_alloc_rx_buf(edma_cinfo, ring, ring->count, j);
+ if (ret_count) {
+ dev_dbg(&edma_cinfo->pdev->dev, "not all rx buffers allocated\n");
+ }
+ j += ((edma_cinfo->num_rx_queues == 4) ? 2 : 1);
+ }
+
+ /* Configure descriptor Ring */
+ edma_init_desc(edma_cinfo);
+ return 0;
+}
+
+/* edma_irq_enable()
+ * Enable default interrupt generation settings
+ */
+void edma_irq_enable(struct edma_common_info *edma_cinfo)
+{
+ struct edma_hw *hw = &edma_cinfo->hw;
+ int i, j;
+
+ edma_write_reg(EDMA_REG_RX_ISR, 0xff);
+ for (i = 0, j = 0; i < edma_cinfo->num_rx_queues; i++) {
+ edma_write_reg(EDMA_REG_RX_INT_MASK_Q(j), hw->rx_intr_mask);
+ j += ((edma_cinfo->num_rx_queues == 4) ? 2 : 1);
+ }
+ edma_write_reg(EDMA_REG_TX_ISR, 0xffff);
+ for (i = 0; i < edma_cinfo->num_tx_queues; i++)
+ edma_write_reg(EDMA_REG_TX_INT_MASK_Q(i), hw->tx_intr_mask);
+}
+
+/* edma_irq_disable()
+ * Disable Interrupt
+ */
+void edma_irq_disable(struct edma_common_info *edma_cinfo)
+{
+ int i;
+
+ for (i = 0; i < EDMA_MAX_RECEIVE_QUEUE; i++)
+ edma_write_reg(EDMA_REG_RX_INT_MASK_Q(i), 0x0);
+
+ for (i = 0; i < EDMA_MAX_TRANSMIT_QUEUE; i++)
+ edma_write_reg(EDMA_REG_TX_INT_MASK_Q(i), 0x0);
+ edma_write_reg(EDMA_REG_MISC_IMR, 0);
+ edma_write_reg(EDMA_REG_WOL_IMR, 0);
+}
+
+/* edma_free_irqs()
+ * Free All IRQs
+ */
+void edma_free_irqs(struct edma_adapter *adapter)
+{
+ struct edma_common_info *edma_cinfo = adapter->edma_cinfo;
+ int i, j;
+ int k = ((edma_cinfo->num_rx_queues == 4) ? 1 : 2);
+
+ for (i = 0; i < CONFIG_NR_CPUS; i++) {
+ for (j = edma_cinfo->edma_percpu_info[i].tx_start; j < (edma_cinfo->edma_percpu_info[i].tx_start + 4); j++)
+ free_irq(edma_cinfo->tx_irq[j], &edma_cinfo->edma_percpu_info[i]);
+
+ for (j = edma_cinfo->edma_percpu_info[i].rx_start; j < (edma_cinfo->edma_percpu_info[i].rx_start + k); j++)
+ free_irq(edma_cinfo->rx_irq[j], &edma_cinfo->edma_percpu_info[i]);
+ }
+}
+
+/* edma_enable_rx_ctrl()
+ * Enable RX queue control
+ */
+void edma_enable_rx_ctrl(struct edma_hw *hw)
+{
+ u32 data;
+
+ edma_read_reg(EDMA_REG_RXQ_CTRL, &data);
+ data |= EDMA_RXQ_CTRL_EN;
+ edma_write_reg(EDMA_REG_RXQ_CTRL, data);
+}
+
+
+/* edma_enable_tx_ctrl()
+ * Enable TX queue control
+ */
+void edma_enable_tx_ctrl(struct edma_hw *hw)
+{
+ u32 data;
+
+ edma_read_reg(EDMA_REG_TXQ_CTRL, &data);
+ data |= EDMA_TXQ_CTRL_TXQ_EN;
+ edma_write_reg(EDMA_REG_TXQ_CTRL, data);
+}
+
+/* edma_stop_rx_tx()
+ * Disable RX/TQ Queue control
+ */
+void edma_stop_rx_tx(struct edma_hw *hw)
+{
+ u32 data;
+
+ edma_read_reg(EDMA_REG_RXQ_CTRL, &data);
+ data &= ~EDMA_RXQ_CTRL_EN;
+ edma_write_reg(EDMA_REG_RXQ_CTRL, data);
+ edma_read_reg(EDMA_REG_TXQ_CTRL, &data);
+ data &= ~EDMA_TXQ_CTRL_TXQ_EN;
+ edma_write_reg(EDMA_REG_TXQ_CTRL, data);
+}
+
+/* edma_reset()
+ * Reset the EDMA
+ */
+int edma_reset(struct edma_common_info *edma_cinfo)
+{
+ struct edma_hw *hw = &edma_cinfo->hw;
+
+ edma_irq_disable(edma_cinfo);
+
+ edma_clear_irq_status();
+
+ edma_stop_rx_tx(hw);
+
+ return 0;
+}
+
+/* edma_fill_netdev()
+ * Fill netdev for each etdr
+ */
+int edma_fill_netdev(struct edma_common_info *edma_cinfo, int queue_id,
+ int dev, int txq_id)
+{
+ struct edma_tx_desc_ring *etdr;
+ int i = 0;
+
+ etdr = edma_cinfo->tpd_ring[queue_id];
+
+ while (etdr->netdev[i])
+ i++;
+
+ if (i >= EDMA_MAX_NETDEV_PER_QUEUE)
+ return -1;
+
+ /* Populate the netdev associated with the tpd ring */
+ etdr->netdev[i] = edma_netdev[dev];
+ etdr->nq[i] = netdev_get_tx_queue(edma_netdev[dev], txq_id);
+
+ return 0;
+}
+
+/* edma_set_mac()
+ * Change the Ethernet Address of the NIC
+ */
+int edma_set_mac_addr(struct net_device *netdev, void *p)
+{
+ struct sockaddr *addr = p;
+
+ if (!is_valid_ether_addr(addr->sa_data))
+ return -EINVAL;
+
+ if (netif_running(netdev))
+ return -EBUSY;
+
+ memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len);
+ return 0;
+}
+
+/* edma_set_stp_rstp()
+ * set stp/rstp
+ */
+void edma_set_stp_rstp(bool rstp)
+{
+ edma_stp_rstp = rstp;
+}
+
+/* edma_assign_ath_hdr_type()
+ * assign atheros header eth type
+ */
+void edma_assign_ath_hdr_type(int eth_type)
+{
+ edma_ath_eth_type = eth_type & EDMA_ETH_TYPE_MASK;
+}
+
+/* edma_get_default_vlan_tag()
+ * Used by other modules to get the default vlan tag
+ */
+int edma_get_default_vlan_tag(struct net_device *netdev)
+{
+ struct edma_adapter *adapter = netdev_priv(netdev);
+
+ if (adapter->default_vlan_tag)
+ return adapter->default_vlan_tag;
+
+ return 0;
+}
+
+/* edma_open()
+ * gets called when netdevice is up, start the queue.
+ */
+int edma_open(struct net_device *netdev)
+{
+ struct edma_adapter *adapter = netdev_priv(netdev);
+ struct platform_device *pdev = adapter->edma_cinfo->pdev;
+
+ netif_tx_start_all_queues(netdev);
+ edma_initialise_rfs_flow_table(adapter);
+ set_bit(__EDMA_UP, &adapter->state_flags);
+
+ /* if Link polling is enabled, in our case enabled for WAN, then
+ * do a phy start, else always set link as UP
+ */
+ if (adapter->poll_required) {
+ if (!IS_ERR(adapter->phydev)) {
+ phy_start(adapter->phydev);
+ phy_start_aneg(adapter->phydev);
+ adapter->link_state = __EDMA_LINKDOWN;
+ } else {
+ dev_dbg(&pdev->dev, "Invalid PHY device for a link polled interface\n");
+ }
+ } else {
+ adapter->link_state = __EDMA_LINKUP;
+ netif_carrier_on(netdev);
+ }
+
+ return 0;
+}
+
+
+/* edma_close()
+ * gets called when netdevice is down, stops the queue.
+ */
+int edma_close(struct net_device *netdev)
+{
+ struct edma_adapter *adapter = netdev_priv(netdev);
+
+ edma_free_rfs_flow_table(adapter);
+ netif_carrier_off(netdev);
+ netif_tx_stop_all_queues(netdev);
+
+ if (adapter->poll_required) {
+ if (!IS_ERR(adapter->phydev))
+ phy_stop(adapter->phydev);
+ }
+
+ adapter->link_state = __EDMA_LINKDOWN;
+
+ /* Set GMAC state to UP before link state is checked
+ */
+ clear_bit(__EDMA_UP, &adapter->state_flags);
+
+ return 0;
+}
+
+/* edma_poll
+ * polling function that gets called when the napi gets scheduled.
+ *
+ * Main sequence of task performed in this api
+ * is clear irq status -> clear_tx_irq -> clean_rx_irq->
+ * enable interrupts.
+ */
+int edma_poll(struct napi_struct *napi, int budget)
+{
+ struct edma_per_cpu_queues_info *edma_percpu_info = container_of(napi,
+ struct edma_per_cpu_queues_info, napi);
+ struct edma_common_info *edma_cinfo = edma_percpu_info->edma_cinfo;
+ u32 reg_data;
+ u32 shadow_rx_status, shadow_tx_status;
+ int queue_id;
+ int i, work_done = 0;
+ u16 rx_pending_fill;
+
+ /* Store the Rx/Tx status by ANDing it with
+ * appropriate CPU RX?TX mask
+ */
+ edma_read_reg(EDMA_REG_RX_ISR, ®_data);
+ edma_percpu_info->rx_status |= reg_data & edma_percpu_info->rx_mask;
+ shadow_rx_status = edma_percpu_info->rx_status;
+ edma_read_reg(EDMA_REG_TX_ISR, ®_data);
+ edma_percpu_info->tx_status |= reg_data & edma_percpu_info->tx_mask;
+ shadow_tx_status = edma_percpu_info->tx_status;
+
+ /* Every core will have a start, which will be computed
+ * in probe and stored in edma_percpu_info->tx_start variable.
+ * We will shift the status bit by tx_start to obtain
+ * status bits for the core on which the current processing
+ * is happening. Since, there are 4 tx queues per core,
+ * we will run the loop till we get the correct queue to clear.
+ */
+ while (edma_percpu_info->tx_status) {
+ queue_id = ffs(edma_percpu_info->tx_status) - 1;
+ edma_tx_complete(edma_cinfo, queue_id);
+ edma_percpu_info->tx_status &= ~(1 << queue_id);
+ }
+
+ /* Every core will have a start, which will be computed
+ * in probe and stored in edma_percpu_info->tx_start variable.
+ * We will shift the status bit by tx_start to obtain
+ * status bits for the core on which the current processing
+ * is happening. Since, there are 4 tx queues per core, we
+ * will run the loop till we get the correct queue to clear.
+ */
+ while (edma_percpu_info->rx_status) {
+ queue_id = ffs(edma_percpu_info->rx_status) - 1;
+ rx_pending_fill = edma_rx_complete(edma_cinfo, &work_done,
+ budget, queue_id, napi);
+
+ if (likely(work_done < budget)) {
+ if (rx_pending_fill) {
+ /* reschedule poll() to refill rx buffer deficit */
+ work_done = budget;
+ break;
+ }
+ edma_percpu_info->rx_status &= ~(1 << queue_id);
+ } else {
+ break;
+ }
+ }
+
+ /* Clear the status register, to avoid the interrupts to
+ * reoccur.This clearing of interrupt status register is
+ * done here as writing to status register only takes place
+ * once the producer/consumer index has been updated to
+ * reflect that the packet transmission/reception went fine.
+ */
+ edma_write_reg(EDMA_REG_RX_ISR, shadow_rx_status);
+ edma_write_reg(EDMA_REG_TX_ISR, shadow_tx_status);
+
+ /* If budget not fully consumed, exit the polling mode */
+ if (likely(work_done < budget)) {
+ napi_complete(napi);
+
+ /* re-enable the interrupts */
+ for (i = 0; i < edma_cinfo->num_rxq_per_core; i++)
+ edma_write_reg(EDMA_REG_RX_INT_MASK_Q(edma_percpu_info->rx_start + i), 0x1);
+ for (i = 0; i < edma_cinfo->num_txq_per_core; i++)
+ edma_write_reg(EDMA_REG_TX_INT_MASK_Q(edma_percpu_info->tx_start + i), 0x1);
+ }
+
+ return work_done;
+}
+
+/* edma interrupt()
+ * interrupt handler
+ */
+irqreturn_t edma_interrupt(int irq, void *dev)
+{
+ struct edma_per_cpu_queues_info *edma_percpu_info = (struct edma_per_cpu_queues_info *) dev;
+ struct edma_common_info *edma_cinfo = edma_percpu_info->edma_cinfo;
+ int i;
+
+ /* Unmask the TX/RX interrupt register */
+ for (i = 0; i < edma_cinfo->num_rxq_per_core; i++)
+ edma_write_reg(EDMA_REG_RX_INT_MASK_Q(edma_percpu_info->rx_start + i), 0x0);
+
+ for (i = 0; i < edma_cinfo->num_txq_per_core; i++)
+ edma_write_reg(EDMA_REG_TX_INT_MASK_Q(edma_percpu_info->tx_start + i), 0x0);
+
+ napi_schedule(&edma_percpu_info->napi);
+
+ return IRQ_HANDLED;
+}
--- /dev/null
+/*
+ * Copyright (c) 2014 - 2016, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for
+ * any purpose with or without fee is hereby granted, provided that the
+ * above copyright notice and this permission notice appear in all copies.
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT
+ * OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef _EDMA_H_
+#define _EDMA_H_
+
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/types.h>
+#include <linux/errno.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/etherdevice.h>
+#include <linux/skbuff.h>
+#include <linux/io.h>
+#include <linux/vmalloc.h>
+#include <linux/pagemap.h>
+#include <linux/smp.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/clk.h>
+#include <linux/kernel.h>
+#include <linux/device.h>
+#include <linux/sysctl.h>
+#include <linux/phy.h>
+#include <linux/of_net.h>
+#include <net/checksum.h>
+#include <net/ip6_checksum.h>
+#include <asm-generic/bug.h>
+#include "ess_edma.h"
+
+#define EDMA_CPU_CORES_SUPPORTED 4
+#define EDMA_MAX_PORTID_SUPPORTED 5
+#define EDMA_MAX_VLAN_SUPPORTED EDMA_MAX_PORTID_SUPPORTED
+#define EDMA_MAX_PORTID_BITMAP_INDEX (EDMA_MAX_PORTID_SUPPORTED + 1)
+#define EDMA_MAX_PORTID_BITMAP_SUPPORTED 0x1f /* 0001_1111 = 0x1f */
+#define EDMA_MAX_NETDEV_PER_QUEUE 4 /* 3 Netdev per queue, 1 space for indexing */
+
+#define EDMA_MAX_RECEIVE_QUEUE 8
+#define EDMA_MAX_TRANSMIT_QUEUE 16
+
+/* WAN/LAN adapter number */
+#define EDMA_WAN 0
+#define EDMA_LAN 1
+
+/* VLAN tag */
+#define EDMA_LAN_DEFAULT_VLAN 1
+#define EDMA_WAN_DEFAULT_VLAN 2
+
+#define EDMA_DEFAULT_GROUP1_VLAN 1
+#define EDMA_DEFAULT_GROUP2_VLAN 2
+#define EDMA_DEFAULT_GROUP3_VLAN 3
+#define EDMA_DEFAULT_GROUP4_VLAN 4
+#define EDMA_DEFAULT_GROUP5_VLAN 5
+
+/* Queues exposed to linux kernel */
+#define EDMA_NETDEV_TX_QUEUE 4
+#define EDMA_NETDEV_RX_QUEUE 4
+
+/* Number of queues per core */
+#define EDMA_NUM_TXQ_PER_CORE 4
+#define EDMA_NUM_RXQ_PER_CORE 2
+
+#define EDMA_TPD_EOP_SHIFT 31
+
+#define EDMA_PORT_ID_SHIFT 12
+#define EDMA_PORT_ID_MASK 0x7
+
+/* tpd word 3 bit 18-28 */
+#define EDMA_TPD_PORT_BITMAP_SHIFT 18
+
+#define EDMA_TPD_FROM_CPU_SHIFT 25
+
+#define EDMA_FROM_CPU_MASK 0x80
+#define EDMA_SKB_PRIORITY_MASK 0x38
+
+/* TX/RX descriptor ring count */
+/* should be a power of 2 */
+#define EDMA_RX_RING_SIZE 128
+#define EDMA_TX_RING_SIZE 128
+
+/* Flags used in paged/non paged mode */
+#define EDMA_RX_HEAD_BUFF_SIZE_JUMBO 256
+#define EDMA_RX_HEAD_BUFF_SIZE 1540
+
+/* MAX frame size supported by switch */
+#define EDMA_MAX_JUMBO_FRAME_SIZE 9216
+
+/* Configurations */
+#define EDMA_INTR_CLEAR_TYPE 0
+#define EDMA_INTR_SW_IDX_W_TYPE 0
+#define EDMA_FIFO_THRESH_TYPE 0
+#define EDMA_RSS_TYPE 0
+#define EDMA_RX_IMT 0x0020
+#define EDMA_TX_IMT 0x0050
+#define EDMA_TPD_BURST 5
+#define EDMA_TXF_BURST 0x100
+#define EDMA_RFD_BURST 8
+#define EDMA_RFD_THR 16
+#define EDMA_RFD_LTHR 0
+
+/* RX/TX per CPU based mask/shift */
+#define EDMA_TX_PER_CPU_MASK 0xF
+#define EDMA_RX_PER_CPU_MASK 0x3
+#define EDMA_TX_PER_CPU_MASK_SHIFT 0x2
+#define EDMA_RX_PER_CPU_MASK_SHIFT 0x1
+#define EDMA_TX_CPU_START_SHIFT 0x2
+#define EDMA_RX_CPU_START_SHIFT 0x1
+
+/* FLags used in transmit direction */
+#define EDMA_HW_CHECKSUM 0x00000001
+#define EDMA_VLAN_TX_TAG_INSERT_FLAG 0x00000002
+#define EDMA_VLAN_TX_TAG_INSERT_DEFAULT_FLAG 0x00000004
+
+#define EDMA_SW_DESC_FLAG_LAST 0x1
+#define EDMA_SW_DESC_FLAG_SKB_HEAD 0x2
+#define EDMA_SW_DESC_FLAG_SKB_FRAG 0x4
+#define EDMA_SW_DESC_FLAG_SKB_FRAGLIST 0x8
+#define EDMA_SW_DESC_FLAG_SKB_NONE 0x10
+#define EDMA_SW_DESC_FLAG_SKB_REUSE 0x20
+
+
+#define EDMA_MAX_SKB_FRAGS (MAX_SKB_FRAGS + 1)
+
+/* Ethtool specific list of EDMA supported features */
+#define EDMA_SUPPORTED_FEATURES (SUPPORTED_10baseT_Half \
+ | SUPPORTED_10baseT_Full \
+ | SUPPORTED_100baseT_Half \
+ | SUPPORTED_100baseT_Full \
+ | SUPPORTED_1000baseT_Full)
+
+/* Recevie side atheros Header */
+#define EDMA_RX_ATH_HDR_VERSION 0x2
+#define EDMA_RX_ATH_HDR_VERSION_SHIFT 14
+#define EDMA_RX_ATH_HDR_PRIORITY_SHIFT 11
+#define EDMA_RX_ATH_PORT_TYPE_SHIFT 6
+#define EDMA_RX_ATH_HDR_RSTP_PORT_TYPE 0x4
+
+/* Transmit side atheros Header */
+#define EDMA_TX_ATH_HDR_PORT_BITMAP_MASK 0x7F
+#define EDMA_TX_ATH_HDR_FROM_CPU_MASK 0x80
+#define EDMA_TX_ATH_HDR_FROM_CPU_SHIFT 7
+
+#define EDMA_TXQ_START_CORE0 8
+#define EDMA_TXQ_START_CORE1 12
+#define EDMA_TXQ_START_CORE2 0
+#define EDMA_TXQ_START_CORE3 4
+
+#define EDMA_TXQ_IRQ_MASK_CORE0 0x0F00
+#define EDMA_TXQ_IRQ_MASK_CORE1 0xF000
+#define EDMA_TXQ_IRQ_MASK_CORE2 0x000F
+#define EDMA_TXQ_IRQ_MASK_CORE3 0x00F0
+
+#define EDMA_ETH_HDR_LEN 12
+#define EDMA_ETH_TYPE_MASK 0xFFFF
+
+#define EDMA_RX_BUFFER_WRITE 16
+#define EDMA_RFD_AVAIL_THR 80
+
+#define EDMA_GMAC_NO_MDIO_PHY PHY_MAX_ADDR
+
+extern int ssdk_rfs_ipct_rule_set(__be32 ip_src, __be32 ip_dst,
+ __be16 sport, __be16 dport,
+ uint8_t proto, u16 loadbalance, bool action);
+struct edma_ethtool_statistics {
+ u32 tx_q0_pkt;
+ u32 tx_q1_pkt;
+ u32 tx_q2_pkt;
+ u32 tx_q3_pkt;
+ u32 tx_q4_pkt;
+ u32 tx_q5_pkt;
+ u32 tx_q6_pkt;
+ u32 tx_q7_pkt;
+ u32 tx_q8_pkt;
+ u32 tx_q9_pkt;
+ u32 tx_q10_pkt;
+ u32 tx_q11_pkt;
+ u32 tx_q12_pkt;
+ u32 tx_q13_pkt;
+ u32 tx_q14_pkt;
+ u32 tx_q15_pkt;
+ u32 tx_q0_byte;
+ u32 tx_q1_byte;
+ u32 tx_q2_byte;
+ u32 tx_q3_byte;
+ u32 tx_q4_byte;
+ u32 tx_q5_byte;
+ u32 tx_q6_byte;
+ u32 tx_q7_byte;
+ u32 tx_q8_byte;
+ u32 tx_q9_byte;
+ u32 tx_q10_byte;
+ u32 tx_q11_byte;
+ u32 tx_q12_byte;
+ u32 tx_q13_byte;
+ u32 tx_q14_byte;
+ u32 tx_q15_byte;
+ u32 rx_q0_pkt;
+ u32 rx_q1_pkt;
+ u32 rx_q2_pkt;
+ u32 rx_q3_pkt;
+ u32 rx_q4_pkt;
+ u32 rx_q5_pkt;
+ u32 rx_q6_pkt;
+ u32 rx_q7_pkt;
+ u32 rx_q0_byte;
+ u32 rx_q1_byte;
+ u32 rx_q2_byte;
+ u32 rx_q3_byte;
+ u32 rx_q4_byte;
+ u32 rx_q5_byte;
+ u32 rx_q6_byte;
+ u32 rx_q7_byte;
+ u32 tx_desc_error;
+ u32 rx_alloc_fail_ctr;
+};
+
+struct edma_mdio_data {
+ struct mii_bus *mii_bus;
+ void __iomem *membase;
+ int phy_irq[PHY_MAX_ADDR];
+};
+
+/* EDMA LINK state */
+enum edma_link_state {
+ __EDMA_LINKUP, /* Indicate link is UP */
+ __EDMA_LINKDOWN /* Indicate link is down */
+};
+
+/* EDMA GMAC state */
+enum edma_gmac_state {
+ __EDMA_UP /* use to indicate GMAC is up */
+};
+
+/* edma transmit descriptor */
+struct edma_tx_desc {
+ __le16 len; /* full packet including CRC */
+ __le16 svlan_tag; /* vlan tag */
+ __le32 word1; /* byte 4-7 */
+ __le32 addr; /* address of buffer */
+ __le32 word3; /* byte 12 */
+};
+
+/* edma receive return descriptor */
+struct edma_rx_return_desc {
+ u16 rrd0;
+ u16 rrd1;
+ u16 rrd2;
+ u16 rrd3;
+ u16 rrd4;
+ u16 rrd5;
+ u16 rrd6;
+ u16 rrd7;
+};
+
+/* RFD descriptor */
+struct edma_rx_free_desc {
+ __le32 buffer_addr; /* buffer address */
+};
+
+/* edma hw specific data */
+struct edma_hw {
+ u32 __iomem *hw_addr; /* inner register address */
+ struct edma_adapter *adapter; /* netdevice adapter */
+ u32 rx_intr_mask; /*rx interrupt mask */
+ u32 tx_intr_mask; /* tx interrupt nask */
+ u32 misc_intr_mask; /* misc interrupt mask */
+ u32 wol_intr_mask; /* wake on lan interrupt mask */
+ bool intr_clear_type; /* interrupt clear */
+ bool intr_sw_idx_w; /* interrupt software index */
+ u32 rx_head_buff_size; /* Rx buffer size */
+ u8 rss_type; /* rss protocol type */
+};
+
+/* edma_sw_desc stores software descriptor
+ * SW descriptor has 1:1 map with HW descriptor
+ */
+struct edma_sw_desc {
+ struct sk_buff *skb;
+ dma_addr_t dma; /* dma address */
+ u16 length; /* Tx/Rx buffer length */
+ u32 flags;
+};
+
+/* per core related information */
+struct edma_per_cpu_queues_info {
+ struct napi_struct napi; /* napi associated with the core */
+ u32 tx_mask; /* tx interrupt mask */
+ u32 rx_mask; /* rx interrupt mask */
+ u32 tx_status; /* tx interrupt status */
+ u32 rx_status; /* rx interrupt status */
+ u32 tx_start; /* tx queue start */
+ u32 rx_start; /* rx queue start */
+ struct edma_common_info *edma_cinfo; /* edma common info */
+};
+
+/* edma specific common info */
+struct edma_common_info {
+ struct edma_tx_desc_ring *tpd_ring[16]; /* 16 Tx queues */
+ struct edma_rfd_desc_ring *rfd_ring[8]; /* 8 Rx queues */
+ struct platform_device *pdev; /* device structure */
+ struct net_device *netdev[EDMA_MAX_PORTID_SUPPORTED];
+ struct net_device *portid_netdev_lookup_tbl[EDMA_MAX_PORTID_BITMAP_INDEX];
+ struct ctl_table_header *edma_ctl_table_hdr;
+ int num_gmac;
+ struct edma_ethtool_statistics edma_ethstats; /* ethtool stats */
+ int num_rx_queues; /* number of rx queue */
+ u32 num_tx_queues; /* number of tx queue */
+ u32 tx_irq[16]; /* number of tx irq */
+ u32 rx_irq[8]; /* number of rx irq */
+ u32 from_cpu; /* from CPU TPD field */
+ u32 num_rxq_per_core; /* Rx queues per core */
+ u32 num_txq_per_core; /* Tx queues per core */
+ u16 tx_ring_count; /* Tx ring count */
+ u16 rx_ring_count; /* Rx ring*/
+ u16 rx_head_buffer_len; /* rx buffer length */
+ u16 rx_page_buffer_len; /* rx buffer length */
+ u32 page_mode; /* Jumbo frame supported flag */
+ u32 fraglist_mode; /* fraglist supported flag */
+ struct edma_hw hw; /* edma hw specific structure */
+ struct edma_per_cpu_queues_info edma_percpu_info[CONFIG_NR_CPUS]; /* per cpu information */
+ spinlock_t stats_lock; /* protect edma stats area for updation */
+ struct timer_list edma_stats_timer;
+ bool is_single_phy;
+ void __iomem *ess_hw_addr;
+ struct clk *ess_clk;
+};
+
+/* transimit packet descriptor (tpd) ring */
+struct edma_tx_desc_ring {
+ struct netdev_queue *nq[EDMA_MAX_NETDEV_PER_QUEUE]; /* Linux queue index */
+ struct net_device *netdev[EDMA_MAX_NETDEV_PER_QUEUE];
+ /* Array of netdevs associated with the tpd ring */
+ void *hw_desc; /* descriptor ring virtual address */
+ struct edma_sw_desc *sw_desc; /* buffer associated with ring */
+ int netdev_bmp; /* Bitmap for per-ring netdevs */
+ u32 size; /* descriptor ring length in bytes */
+ u16 count; /* number of descriptors in the ring */
+ dma_addr_t dma; /* descriptor ring physical address */
+ u16 sw_next_to_fill; /* next Tx descriptor to fill */
+ u16 sw_next_to_clean; /* next Tx descriptor to clean */
+};
+
+/* receive free descriptor (rfd) ring */
+struct edma_rfd_desc_ring {
+ void *hw_desc; /* descriptor ring virtual address */
+ struct edma_sw_desc *sw_desc; /* buffer associated with ring */
+ u16 size; /* bytes allocated to sw_desc */
+ u16 count; /* number of descriptors in the ring */
+ dma_addr_t dma; /* descriptor ring physical address */
+ u16 sw_next_to_fill; /* next descriptor to fill */
+ u16 sw_next_to_clean; /* next descriptor to clean */
+ u16 pending_fill; /* fill pending from previous iteration */
+};
+
+/* edma_rfs_flter_node - rfs filter node in hash table */
+struct edma_rfs_filter_node {
+ struct flow_keys keys;
+ u32 flow_id; /* flow_id of filter provided by kernel */
+ u16 filter_id; /* filter id of filter returned by adaptor */
+ u16 rq_id; /* desired rq index */
+ struct hlist_node node; /* edma rfs list node */
+};
+
+/* edma_rfs_flow_tbl - rfs flow table */
+struct edma_rfs_flow_table {
+ u16 max_num_filter; /* Maximum number of filters edma supports */
+ u16 hashtoclean; /* hash table index to clean next */
+ int filter_available; /* Number of free filters available */
+ struct hlist_head hlist_head[EDMA_RFS_FLOW_ENTRIES];
+ spinlock_t rfs_ftab_lock;
+ struct timer_list expire_rfs; /* timer function for edma_rps_may_expire_flow */
+};
+
+/* EDMA net device structure */
+struct edma_adapter {
+ struct net_device *netdev; /* netdevice */
+ struct platform_device *pdev; /* platform device */
+ struct edma_common_info *edma_cinfo; /* edma common info */
+ struct phy_device *phydev; /* Phy device */
+ struct edma_rfs_flow_table rfs; /* edma rfs flow table */
+ struct net_device_stats stats; /* netdev statistics */
+ set_rfs_filter_callback_t set_rfs_rule;
+ u32 flags;/* status flags */
+ unsigned long state_flags; /* GMAC up/down flags */
+ u32 forced_speed; /* link force speed */
+ u32 forced_duplex; /* link force duplex */
+ u32 link_state; /* phy link state */
+ u32 phy_mdio_addr; /* PHY device address on MII interface */
+ u32 poll_required; /* check if link polling is required */
+ u32 tx_start_offset[CONFIG_NR_CPUS]; /* tx queue start */
+ u32 default_vlan_tag; /* vlan tag */
+ u32 dp_bitmap;
+ uint8_t phy_id[MII_BUS_ID_SIZE + 3];
+};
+
+int edma_alloc_queues_tx(struct edma_common_info *edma_cinfo);
+int edma_alloc_queues_rx(struct edma_common_info *edma_cinfo);
+int edma_open(struct net_device *netdev);
+int edma_close(struct net_device *netdev);
+void edma_free_tx_resources(struct edma_common_info *edma_c_info);
+void edma_free_rx_resources(struct edma_common_info *edma_c_info);
+int edma_alloc_tx_rings(struct edma_common_info *edma_cinfo);
+int edma_alloc_rx_rings(struct edma_common_info *edma_cinfo);
+void edma_free_tx_rings(struct edma_common_info *edma_cinfo);
+void edma_free_rx_rings(struct edma_common_info *edma_cinfo);
+void edma_free_queues(struct edma_common_info *edma_cinfo);
+void edma_irq_disable(struct edma_common_info *edma_cinfo);
+int edma_reset(struct edma_common_info *edma_cinfo);
+int edma_poll(struct napi_struct *napi, int budget);
+netdev_tx_t edma_xmit(struct sk_buff *skb,
+ struct net_device *netdev);
+int edma_configure(struct edma_common_info *edma_cinfo);
+void edma_irq_enable(struct edma_common_info *edma_cinfo);
+void edma_enable_tx_ctrl(struct edma_hw *hw);
+void edma_enable_rx_ctrl(struct edma_hw *hw);
+void edma_stop_rx_tx(struct edma_hw *hw);
+void edma_free_irqs(struct edma_adapter *adapter);
+irqreturn_t edma_interrupt(int irq, void *dev);
+void edma_write_reg(u16 reg_addr, u32 reg_value);
+void edma_read_reg(u16 reg_addr, volatile u32 *reg_value);
+struct net_device_stats *edma_get_stats(struct net_device *netdev);
+int edma_set_mac_addr(struct net_device *netdev, void *p);
+int edma_rx_flow_steer(struct net_device *dev, const struct sk_buff *skb,
+ u16 rxq, u32 flow_id);
+int edma_register_rfs_filter(struct net_device *netdev,
+ set_rfs_filter_callback_t set_filter);
+void edma_flow_may_expire(struct timer_list *t);
+void edma_set_ethtool_ops(struct net_device *netdev);
+void edma_set_stp_rstp(bool tag);
+void edma_assign_ath_hdr_type(int tag);
+int edma_get_default_vlan_tag(struct net_device *netdev);
+void edma_adjust_link(struct net_device *netdev);
+int edma_fill_netdev(struct edma_common_info *edma_cinfo, int qid, int num, int txq_id);
+void edma_read_append_stats(struct edma_common_info *edma_cinfo);
+void edma_change_tx_coalesce(int usecs);
+void edma_change_rx_coalesce(int usecs);
+void edma_get_tx_rx_coalesce(u32 *reg_val);
+void edma_clear_irq_status(void);
+void ess_set_port_status_speed(struct edma_common_info *edma_cinfo,
+ struct phy_device *phydev, uint8_t port_id);
+#endif /* _EDMA_H_ */
--- /dev/null
+/*
+ * Copyright (c) 2014 - 2016, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for
+ * any purpose with or without fee is hereby granted, provided that the
+ * above copyright notice and this permission notice appear in all copies.
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT
+ * OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include <linux/cpu_rmap.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
+#include <linux/timer.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/clk.h>
+#include <linux/string.h>
+#include <linux/reset.h>
+#include "edma.h"
+#include "ess_edma.h"
+
+/* Weight round robin and virtual QID mask */
+#define EDMA_WRR_VID_SCTL_MASK 0xffff
+
+/* Weight round robin and virtual QID shift */
+#define EDMA_WRR_VID_SCTL_SHIFT 16
+
+char edma_axi_driver_name[] = "ess_edma";
+static const u32 default_msg = NETIF_MSG_DRV | NETIF_MSG_PROBE |
+ NETIF_MSG_LINK | NETIF_MSG_TIMER | NETIF_MSG_IFDOWN | NETIF_MSG_IFUP;
+
+static u32 edma_hw_addr;
+
+char edma_tx_irq[16][64];
+char edma_rx_irq[8][64];
+struct net_device *edma_netdev[EDMA_MAX_PORTID_SUPPORTED];
+static u16 tx_start[4] = {EDMA_TXQ_START_CORE0, EDMA_TXQ_START_CORE1,
+ EDMA_TXQ_START_CORE2, EDMA_TXQ_START_CORE3};
+static u32 tx_mask[4] = {EDMA_TXQ_IRQ_MASK_CORE0, EDMA_TXQ_IRQ_MASK_CORE1,
+ EDMA_TXQ_IRQ_MASK_CORE2, EDMA_TXQ_IRQ_MASK_CORE3};
+
+static u32 edma_default_ltag __read_mostly = EDMA_LAN_DEFAULT_VLAN;
+static u32 edma_default_wtag __read_mostly = EDMA_WAN_DEFAULT_VLAN;
+static u32 edma_default_group1_vtag __read_mostly = EDMA_DEFAULT_GROUP1_VLAN;
+static u32 edma_default_group2_vtag __read_mostly = EDMA_DEFAULT_GROUP2_VLAN;
+static u32 edma_default_group3_vtag __read_mostly = EDMA_DEFAULT_GROUP3_VLAN;
+static u32 edma_default_group4_vtag __read_mostly = EDMA_DEFAULT_GROUP4_VLAN;
+static u32 edma_default_group5_vtag __read_mostly = EDMA_DEFAULT_GROUP5_VLAN;
+static u32 edma_rss_idt_val = EDMA_RSS_IDT_VALUE;
+static u32 edma_rss_idt_idx;
+
+static int edma_weight_assigned_to_q __read_mostly;
+static int edma_queue_to_virtual_q __read_mostly;
+static bool edma_enable_rstp __read_mostly;
+static int edma_athr_hdr_eth_type __read_mostly;
+
+static int page_mode;
+module_param(page_mode, int, 0);
+MODULE_PARM_DESC(page_mode, "enable page mode");
+
+static int overwrite_mode;
+module_param(overwrite_mode, int, 0);
+MODULE_PARM_DESC(overwrite_mode, "overwrite default page_mode setting");
+
+static int jumbo_mru = EDMA_RX_HEAD_BUFF_SIZE;
+module_param(jumbo_mru, int, 0);
+MODULE_PARM_DESC(jumbo_mru, "enable fraglist support");
+
+static int num_rxq = 4;
+module_param(num_rxq, int, 0);
+MODULE_PARM_DESC(num_rxq, "change the number of rx queues");
+
+void edma_write_reg(u16 reg_addr, u32 reg_value)
+{
+ writel(reg_value, ((void __iomem *)(edma_hw_addr + reg_addr)));
+}
+
+void edma_read_reg(u16 reg_addr, volatile u32 *reg_value)
+{
+ *reg_value = readl((void __iomem *)(edma_hw_addr + reg_addr));
+}
+
+static void ess_write_reg(struct edma_common_info *edma, u16 reg_addr, u32 reg_value)
+{
+ writel(reg_value, ((void __iomem *)
+ ((unsigned long)edma->ess_hw_addr + reg_addr)));
+}
+
+static void ess_read_reg(struct edma_common_info *edma, u16 reg_addr,
+ volatile u32 *reg_value)
+{
+ *reg_value = readl((void __iomem *)
+ ((unsigned long)edma->ess_hw_addr + reg_addr));
+}
+
+static int ess_reset(struct edma_common_info *edma)
+{
+ struct device_node *switch_node = NULL;
+ struct reset_control *ess_rst;
+ u32 regval;
+
+ switch_node = of_find_node_by_name(NULL, "ess-switch");
+ if (!switch_node) {
+ pr_err("switch-node not found\n");
+ return -EINVAL;
+ }
+
+ ess_rst = of_reset_control_get(switch_node, "ess_rst");
+ of_node_put(switch_node);
+
+ if (IS_ERR(ess_rst)) {
+ pr_err("failed to find ess_rst!\n");
+ return -ENOENT;
+ }
+
+ reset_control_assert(ess_rst);
+ msleep(10);
+ reset_control_deassert(ess_rst);
+ msleep(100);
+ reset_control_put(ess_rst);
+
+ /* Enable only port 5 <--> port 0
+ * bits 0:6 bitmap of ports it can fwd to */
+#define SET_PORT_BMP(r,v) \
+ ess_read_reg(edma, r, ®val); \
+ ess_write_reg(edma, r, ((regval & ~0x3F) | v));
+
+ SET_PORT_BMP(ESS_PORT0_LOOKUP_CTRL,0x20);
+ SET_PORT_BMP(ESS_PORT1_LOOKUP_CTRL,0x00);
+ SET_PORT_BMP(ESS_PORT2_LOOKUP_CTRL,0x00);
+ SET_PORT_BMP(ESS_PORT3_LOOKUP_CTRL,0x00);
+ SET_PORT_BMP(ESS_PORT4_LOOKUP_CTRL,0x00);
+ SET_PORT_BMP(ESS_PORT5_LOOKUP_CTRL,0x01);
+ ess_write_reg(edma, ESS_RGMII_CTRL, 0x400);
+ ess_write_reg(edma, ESS_PORT0_STATUS, ESS_PORT_1G_FDX);
+ ess_write_reg(edma, ESS_PORT5_STATUS, ESS_PORT_1G_FDX);
+ ess_write_reg(edma, ESS_PORT0_HEADER_CTRL, 0);
+#undef SET_PORT_BMP
+
+ /* forward multicast and broadcast frames to CPU */
+ ess_write_reg(edma, ESS_FWD_CTRL1,
+ (ESS_PORTS_ALL << ESS_FWD_CTRL1_UC_FLOOD_S) |
+ (ESS_PORTS_ALL << ESS_FWD_CTRL1_MC_FLOOD_S) |
+ (ESS_PORTS_ALL << ESS_FWD_CTRL1_BC_FLOOD_S));
+
+ return 0;
+}
+
+void ess_set_port_status_speed(struct edma_common_info *edma,
+ struct phy_device *phydev, uint8_t port_id)
+{
+ uint16_t reg_off = ESS_PORT0_STATUS + (4 * port_id);
+ uint32_t reg_val = 0;
+
+ ess_read_reg(edma, reg_off, ®_val);
+
+ /* reset the speed bits [0:1] */
+ reg_val &= ~ESS_PORT_STATUS_SPEED_INV;
+
+ /* set the new speed */
+ switch(phydev->speed) {
+ case SPEED_1000: reg_val |= ESS_PORT_STATUS_SPEED_1000; break;
+ case SPEED_100: reg_val |= ESS_PORT_STATUS_SPEED_100; break;
+ case SPEED_10: reg_val |= ESS_PORT_STATUS_SPEED_10; break;
+ default: reg_val |= ESS_PORT_STATUS_SPEED_INV; break;
+ }
+
+ /* check full/half duplex */
+ if (phydev->duplex) {
+ reg_val |= ESS_PORT_STATUS_DUPLEX_MODE;
+ } else {
+ reg_val &= ~ESS_PORT_STATUS_DUPLEX_MODE;
+ }
+
+ ess_write_reg(edma, reg_off, reg_val);
+}
+
+/* edma_change_tx_coalesce()
+ * change tx interrupt moderation timer
+ */
+void edma_change_tx_coalesce(int usecs)
+{
+ u32 reg_value;
+
+ /* Here, we right shift the value from the user by 1, this is
+ * done because IMT resolution timer is 2usecs. 1 count
+ * of this register corresponds to 2 usecs.
+ */
+ edma_read_reg(EDMA_REG_IRQ_MODRT_TIMER_INIT, ®_value);
+ reg_value = ((reg_value & 0xffff) | ((usecs >> 1) << 16));
+ edma_write_reg(EDMA_REG_IRQ_MODRT_TIMER_INIT, reg_value);
+}
+
+/* edma_change_rx_coalesce()
+ * change rx interrupt moderation timer
+ */
+void edma_change_rx_coalesce(int usecs)
+{
+ u32 reg_value;
+
+ /* Here, we right shift the value from the user by 1, this is
+ * done because IMT resolution timer is 2usecs. 1 count
+ * of this register corresponds to 2 usecs.
+ */
+ edma_read_reg(EDMA_REG_IRQ_MODRT_TIMER_INIT, ®_value);
+ reg_value = ((reg_value & 0xffff0000) | (usecs >> 1));
+ edma_write_reg(EDMA_REG_IRQ_MODRT_TIMER_INIT, reg_value);
+}
+
+/* edma_get_tx_rx_coalesce()
+ * Get tx/rx interrupt moderation value
+ */
+void edma_get_tx_rx_coalesce(u32 *reg_val)
+{
+ edma_read_reg(EDMA_REG_IRQ_MODRT_TIMER_INIT, reg_val);
+}
+
+void edma_read_append_stats(struct edma_common_info *edma_cinfo)
+{
+ uint32_t *p;
+ int i;
+ u32 stat;
+
+ spin_lock_bh(&edma_cinfo->stats_lock);
+ p = (uint32_t *)&(edma_cinfo->edma_ethstats);
+
+ for (i = 0; i < EDMA_MAX_TRANSMIT_QUEUE; i++) {
+ edma_read_reg(EDMA_REG_TX_STAT_PKT_Q(i), &stat);
+ *p += stat;
+ p++;
+ }
+
+ for (i = 0; i < EDMA_MAX_TRANSMIT_QUEUE; i++) {
+ edma_read_reg(EDMA_REG_TX_STAT_BYTE_Q(i), &stat);
+ *p += stat;
+ p++;
+ }
+
+ for (i = 0; i < EDMA_MAX_RECEIVE_QUEUE; i++) {
+ edma_read_reg(EDMA_REG_RX_STAT_PKT_Q(i), &stat);
+ *p += stat;
+ p++;
+ }
+
+ for (i = 0; i < EDMA_MAX_RECEIVE_QUEUE; i++) {
+ edma_read_reg(EDMA_REG_RX_STAT_BYTE_Q(i), &stat);
+ *p += stat;
+ p++;
+ }
+
+ spin_unlock_bh(&edma_cinfo->stats_lock);
+}
+
+static void edma_statistics_timer(struct timer_list *t)
+{
+ struct edma_common_info *edma_cinfo =
+ from_timer(edma_cinfo, t, edma_stats_timer);
+
+ edma_read_append_stats(edma_cinfo);
+
+ mod_timer(&edma_cinfo->edma_stats_timer, jiffies + 1*HZ);
+}
+
+static int edma_enable_stp_rstp(struct ctl_table *table, int write,
+ void __user *buffer, size_t *lenp,
+ loff_t *ppos)
+{
+ int ret;
+
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
+ if (write)
+ edma_set_stp_rstp(edma_enable_rstp);
+
+ return ret;
+}
+
+static int edma_ath_hdr_eth_type(struct ctl_table *table, int write,
+ void __user *buffer, size_t *lenp,
+ loff_t *ppos)
+{
+ int ret;
+
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
+ if (write)
+ edma_assign_ath_hdr_type(edma_athr_hdr_eth_type);
+
+ return ret;
+}
+
+static int edma_change_default_lan_vlan(struct ctl_table *table, int write,
+ void __user *buffer, size_t *lenp,
+ loff_t *ppos)
+{
+ struct edma_adapter *adapter;
+ int ret;
+
+ if (!edma_netdev[1]) {
+ pr_err("Netdevice for default_lan does not exist\n");
+ return -1;
+ }
+
+ adapter = netdev_priv(edma_netdev[1]);
+
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
+
+ if (write)
+ adapter->default_vlan_tag = edma_default_ltag;
+
+ return ret;
+}
+
+static int edma_change_default_wan_vlan(struct ctl_table *table, int write,
+ void __user *buffer, size_t *lenp,
+ loff_t *ppos)
+{
+ struct edma_adapter *adapter;
+ int ret;
+
+ if (!edma_netdev[0]) {
+ pr_err("Netdevice for default_wan does not exist\n");
+ return -1;
+ }
+
+ adapter = netdev_priv(edma_netdev[0]);
+
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
+
+ if (write)
+ adapter->default_vlan_tag = edma_default_wtag;
+
+ return ret;
+}
+
+static int edma_change_group1_vtag(struct ctl_table *table, int write,
+ void __user *buffer, size_t *lenp,
+ loff_t *ppos)
+{
+ struct edma_adapter *adapter;
+ struct edma_common_info *edma_cinfo;
+ int ret;
+
+ if (!edma_netdev[0]) {
+ pr_err("Netdevice for Group 1 does not exist\n");
+ return -1;
+ }
+
+ adapter = netdev_priv(edma_netdev[0]);
+ edma_cinfo = adapter->edma_cinfo;
+
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
+
+ if (write)
+ adapter->default_vlan_tag = edma_default_group1_vtag;
+
+ return ret;
+}
+
+static int edma_change_group2_vtag(struct ctl_table *table, int write,
+ void __user *buffer, size_t *lenp,
+ loff_t *ppos)
+{
+ struct edma_adapter *adapter;
+ struct edma_common_info *edma_cinfo;
+ int ret;
+
+ if (!edma_netdev[1]) {
+ pr_err("Netdevice for Group 2 does not exist\n");
+ return -1;
+ }
+
+ adapter = netdev_priv(edma_netdev[1]);
+ edma_cinfo = adapter->edma_cinfo;
+
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
+
+ if (write)
+ adapter->default_vlan_tag = edma_default_group2_vtag;
+
+ return ret;
+}
+
+static int edma_change_group3_vtag(struct ctl_table *table, int write,
+ void __user *buffer, size_t *lenp,
+ loff_t *ppos)
+{
+ struct edma_adapter *adapter;
+ struct edma_common_info *edma_cinfo;
+ int ret;
+
+ if (!edma_netdev[2]) {
+ pr_err("Netdevice for Group 3 does not exist\n");
+ return -1;
+ }
+
+ adapter = netdev_priv(edma_netdev[2]);
+ edma_cinfo = adapter->edma_cinfo;
+
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
+
+ if (write)
+ adapter->default_vlan_tag = edma_default_group3_vtag;
+
+ return ret;
+}
+
+static int edma_change_group4_vtag(struct ctl_table *table, int write,
+ void __user *buffer, size_t *lenp,
+ loff_t *ppos)
+{
+ struct edma_adapter *adapter;
+ struct edma_common_info *edma_cinfo;
+ int ret;
+
+ if (!edma_netdev[3]) {
+ pr_err("Netdevice for Group 4 does not exist\n");
+ return -1;
+ }
+
+ adapter = netdev_priv(edma_netdev[3]);
+ edma_cinfo = adapter->edma_cinfo;
+
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
+
+ if (write)
+ adapter->default_vlan_tag = edma_default_group4_vtag;
+
+ return ret;
+}
+
+static int edma_change_group5_vtag(struct ctl_table *table, int write,
+ void __user *buffer, size_t *lenp,
+ loff_t *ppos)
+{
+ struct edma_adapter *adapter;
+ struct edma_common_info *edma_cinfo;
+ int ret;
+
+ if (!edma_netdev[4]) {
+ pr_err("Netdevice for Group 5 does not exist\n");
+ return -1;
+ }
+
+ adapter = netdev_priv(edma_netdev[4]);
+ edma_cinfo = adapter->edma_cinfo;
+
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
+
+ if (write)
+ adapter->default_vlan_tag = edma_default_group5_vtag;
+
+ return ret;
+}
+
+static int edma_set_rss_idt_value(struct ctl_table *table, int write,
+ void __user *buffer, size_t *lenp,
+ loff_t *ppos)
+{
+ int ret;
+
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
+ if (write && !ret)
+ edma_write_reg(EDMA_REG_RSS_IDT(edma_rss_idt_idx),
+ edma_rss_idt_val);
+ return ret;
+}
+
+static int edma_set_rss_idt_idx(struct ctl_table *table, int write,
+ void __user *buffer, size_t *lenp,
+ loff_t *ppos)
+{
+ int ret;
+ u32 old_value = edma_rss_idt_idx;
+
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
+ if (!write || ret)
+ return ret;
+
+ if (edma_rss_idt_idx >= EDMA_NUM_IDT) {
+ pr_err("Invalid RSS indirection table index %d\n",
+ edma_rss_idt_idx);
+ edma_rss_idt_idx = old_value;
+ return -EINVAL;
+ }
+ return ret;
+}
+
+static int edma_weight_assigned_to_queues(struct ctl_table *table, int write,
+ void __user *buffer, size_t *lenp,
+ loff_t *ppos)
+{
+ int ret, queue_id, weight;
+ u32 reg_data, data, reg_addr;
+
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
+ if (write) {
+ queue_id = edma_weight_assigned_to_q & EDMA_WRR_VID_SCTL_MASK;
+ if (queue_id < 0 || queue_id > 15) {
+ pr_err("queue_id not within desired range\n");
+ return -EINVAL;
+ }
+
+ weight = edma_weight_assigned_to_q >> EDMA_WRR_VID_SCTL_SHIFT;
+ if (weight < 0 || weight > 0xF) {
+ pr_err("queue_id not within desired range\n");
+ return -EINVAL;
+ }
+
+ data = weight << EDMA_WRR_SHIFT(queue_id);
+
+ reg_addr = EDMA_REG_WRR_CTRL_Q0_Q3 + (queue_id & ~0x3);
+ edma_read_reg(reg_addr, ®_data);
+ reg_data &= ~(1 << EDMA_WRR_SHIFT(queue_id));
+ edma_write_reg(reg_addr, data | reg_data);
+ }
+
+ return ret;
+}
+
+static int edma_queue_to_virtual_queue_map(struct ctl_table *table, int write,
+ void __user *buffer, size_t *lenp,
+ loff_t *ppos)
+{
+ int ret, queue_id, virtual_qid;
+ u32 reg_data, data, reg_addr;
+
+ ret = proc_dointvec(table, write, buffer, lenp, ppos);
+ if (write) {
+ queue_id = edma_queue_to_virtual_q & EDMA_WRR_VID_SCTL_MASK;
+ if (queue_id < 0 || queue_id > 15) {
+ pr_err("queue_id not within desired range\n");
+ return -EINVAL;
+ }
+
+ virtual_qid = edma_queue_to_virtual_q >>
+ EDMA_WRR_VID_SCTL_SHIFT;
+ if (virtual_qid < 0 || virtual_qid > 8) {
+ pr_err("queue_id not within desired range\n");
+ return -EINVAL;
+ }
+
+ data = virtual_qid << EDMA_VQ_ID_SHIFT(queue_id);
+
+ reg_addr = EDMA_REG_VQ_CTRL0 + (queue_id & ~0x3);
+ edma_read_reg(reg_addr, ®_data);
+ reg_data &= ~(1 << EDMA_VQ_ID_SHIFT(queue_id));
+ edma_write_reg(reg_addr, data | reg_data);
+ }
+
+ return ret;
+}
+
+static struct ctl_table edma_table[] = {
+ {
+ .procname = "default_lan_tag",
+ .data = &edma_default_ltag,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = edma_change_default_lan_vlan
+ },
+ {
+ .procname = "default_wan_tag",
+ .data = &edma_default_wtag,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = edma_change_default_wan_vlan
+ },
+ {
+ .procname = "weight_assigned_to_queues",
+ .data = &edma_weight_assigned_to_q,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = edma_weight_assigned_to_queues
+ },
+ {
+ .procname = "queue_to_virtual_queue_map",
+ .data = &edma_queue_to_virtual_q,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = edma_queue_to_virtual_queue_map
+ },
+ {
+ .procname = "enable_stp_rstp",
+ .data = &edma_enable_rstp,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = edma_enable_stp_rstp
+ },
+ {
+ .procname = "athr_hdr_eth_type",
+ .data = &edma_athr_hdr_eth_type,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = edma_ath_hdr_eth_type
+ },
+ {
+ .procname = "default_group1_vlan_tag",
+ .data = &edma_default_group1_vtag,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = edma_change_group1_vtag
+ },
+ {
+ .procname = "default_group2_vlan_tag",
+ .data = &edma_default_group2_vtag,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = edma_change_group2_vtag
+ },
+ {
+ .procname = "default_group3_vlan_tag",
+ .data = &edma_default_group3_vtag,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = edma_change_group3_vtag
+ },
+ {
+ .procname = "default_group4_vlan_tag",
+ .data = &edma_default_group4_vtag,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = edma_change_group4_vtag
+ },
+ {
+ .procname = "default_group5_vlan_tag",
+ .data = &edma_default_group5_vtag,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = edma_change_group5_vtag
+ },
+ {
+ .procname = "edma_rss_idt_value",
+ .data = &edma_rss_idt_val,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = edma_set_rss_idt_value
+ },
+ {
+ .procname = "edma_rss_idt_idx",
+ .data = &edma_rss_idt_idx,
+ .maxlen = sizeof(int),
+ .mode = 0644,
+ .proc_handler = edma_set_rss_idt_idx
+ },
+ {}
+};
+
+static int ess_parse(struct edma_common_info *edma)
+{
+ struct device_node *switch_node;
+ int ret = -EINVAL;
+
+ switch_node = of_find_node_by_name(NULL, "ess-switch");
+ if (!switch_node) {
+ pr_err("cannot find ess-switch node\n");
+ goto out;
+ }
+
+ edma->ess_hw_addr = of_io_request_and_map(switch_node,
+ 0, KBUILD_MODNAME);
+ if (!edma->ess_hw_addr) {
+ pr_err("%s ioremap fail.", __func__);
+ goto out;
+ }
+
+ edma->ess_clk = of_clk_get_by_name(switch_node, "ess_clk");
+ ret = clk_prepare_enable(edma->ess_clk);
+out:
+ of_node_put(switch_node);
+ return ret;
+}
+
+/* edma_axi_netdev_ops
+ * Describe the operations supported by registered netdevices
+ *
+ * static const struct net_device_ops edma_axi_netdev_ops = {
+ * .ndo_open = edma_open,
+ * .ndo_stop = edma_close,
+ * .ndo_start_xmit = edma_xmit_frame,
+ * .ndo_set_mac_address = edma_set_mac_addr,
+ * }
+ */
+static const struct net_device_ops edma_axi_netdev_ops = {
+ .ndo_open = edma_open,
+ .ndo_stop = edma_close,
+ .ndo_start_xmit = edma_xmit,
+ .ndo_set_mac_address = edma_set_mac_addr,
+#ifdef CONFIG_RFS_ACCEL
+ .ndo_rx_flow_steer = edma_rx_flow_steer,
+ .ndo_register_rfs_filter = edma_register_rfs_filter,
+ .ndo_get_default_vlan_tag = edma_get_default_vlan_tag,
+#endif
+ .ndo_get_stats = edma_get_stats,
+};
+
+/* edma_axi_probe()
+ * Initialise an adapter identified by a platform_device structure.
+ *
+ * The OS initialization, configuring of the adapter private structure,
+ * and a hardware reset occur in the probe.
+ */
+static int edma_axi_probe(struct platform_device *pdev)
+{
+ struct edma_common_info *edma_cinfo;
+ struct edma_hw *hw;
+ struct edma_adapter *adapter[EDMA_MAX_PORTID_SUPPORTED];
+ struct resource *res;
+ struct device_node *np = pdev->dev.of_node;
+ struct device_node *pnp;
+ struct device_node *mdio_node = NULL;
+ struct platform_device *mdio_plat = NULL;
+ struct mii_bus *miibus = NULL;
+ struct edma_mdio_data *mdio_data = NULL;
+ int i, j, k, err = 0;
+ int portid_bmp;
+ int idx = 0, idx_mac = 0;
+
+ if (CONFIG_NR_CPUS != EDMA_CPU_CORES_SUPPORTED) {
+ dev_err(&pdev->dev, "Invalid CPU Cores\n");
+ return -EINVAL;
+ }
+
+ if ((num_rxq != 4) && (num_rxq != 8)) {
+ dev_err(&pdev->dev, "Invalid RX queue, edma probe failed\n");
+ return -EINVAL;
+ }
+ edma_cinfo = kzalloc(sizeof(struct edma_common_info), GFP_KERNEL);
+ if (!edma_cinfo) {
+ err = -ENOMEM;
+ goto err_alloc;
+ }
+
+ edma_cinfo->pdev = pdev;
+
+ of_property_read_u32(np, "qcom,num_gmac", &edma_cinfo->num_gmac);
+ if (edma_cinfo->num_gmac > EDMA_MAX_PORTID_SUPPORTED) {
+ pr_err("Invalid DTSI Entry for qcom,num_gmac\n");
+ err = -EINVAL;
+ goto err_cinfo;
+ }
+
+ /* Initialize the netdev array before allocation
+ * to avoid double free
+ */
+ for (i = 0 ; i < edma_cinfo->num_gmac ; i++)
+ edma_netdev[i] = NULL;
+
+ for (i = 0 ; i < edma_cinfo->num_gmac ; i++) {
+ edma_netdev[i] = alloc_etherdev_mqs(sizeof(struct edma_adapter),
+ EDMA_NETDEV_TX_QUEUE, EDMA_NETDEV_RX_QUEUE);
+
+ if (!edma_netdev[i]) {
+ dev_err(&pdev->dev,
+ "net device alloc fails for index=%d\n", i);
+ err = -ENODEV;
+ goto err_ioremap;
+ }
+
+ SET_NETDEV_DEV(edma_netdev[i], &pdev->dev);
+ platform_set_drvdata(pdev, edma_netdev[i]);
+ edma_cinfo->netdev[i] = edma_netdev[i];
+ }
+
+ /* Fill ring details */
+ edma_cinfo->num_tx_queues = EDMA_MAX_TRANSMIT_QUEUE;
+ edma_cinfo->num_txq_per_core = (EDMA_MAX_TRANSMIT_QUEUE / 4);
+ edma_cinfo->tx_ring_count = EDMA_TX_RING_SIZE;
+
+ /* Update num rx queues based on module parameter */
+ edma_cinfo->num_rx_queues = num_rxq;
+ edma_cinfo->num_rxq_per_core = ((num_rxq == 4) ? 1 : 2);
+
+ edma_cinfo->rx_ring_count = EDMA_RX_RING_SIZE;
+
+ hw = &edma_cinfo->hw;
+
+ /* Fill HW defaults */
+ hw->tx_intr_mask = EDMA_TX_IMR_NORMAL_MASK;
+ hw->rx_intr_mask = EDMA_RX_IMR_NORMAL_MASK;
+
+ of_property_read_u32(np, "qcom,page-mode", &edma_cinfo->page_mode);
+ of_property_read_u32(np, "qcom,rx_head_buf_size",
+ &hw->rx_head_buff_size);
+
+ if (overwrite_mode) {
+ dev_info(&pdev->dev, "page mode overwritten");
+ edma_cinfo->page_mode = page_mode;
+ }
+
+ if (jumbo_mru)
+ edma_cinfo->fraglist_mode = 1;
+
+ if (edma_cinfo->page_mode)
+ hw->rx_head_buff_size = EDMA_RX_HEAD_BUFF_SIZE_JUMBO;
+ else if (edma_cinfo->fraglist_mode)
+ hw->rx_head_buff_size = jumbo_mru;
+ else if (!hw->rx_head_buff_size)
+ hw->rx_head_buff_size = EDMA_RX_HEAD_BUFF_SIZE;
+
+ hw->misc_intr_mask = 0;
+ hw->wol_intr_mask = 0;
+
+ hw->intr_clear_type = EDMA_INTR_CLEAR_TYPE;
+ hw->intr_sw_idx_w = EDMA_INTR_SW_IDX_W_TYPE;
+
+ /* configure RSS type to the different protocol that can be
+ * supported
+ */
+ hw->rss_type = EDMA_RSS_TYPE_IPV4TCP | EDMA_RSS_TYPE_IPV6_TCP |
+ EDMA_RSS_TYPE_IPV4_UDP | EDMA_RSS_TYPE_IPV6UDP |
+ EDMA_RSS_TYPE_IPV4 | EDMA_RSS_TYPE_IPV6;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+ edma_cinfo->hw.hw_addr = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(edma_cinfo->hw.hw_addr)) {
+ err = PTR_ERR(edma_cinfo->hw.hw_addr);
+ goto err_ioremap;
+ }
+
+ edma_hw_addr = (u32)edma_cinfo->hw.hw_addr;
+
+ /* Parse tx queue interrupt number from device tree */
+ for (i = 0; i < edma_cinfo->num_tx_queues; i++)
+ edma_cinfo->tx_irq[i] = platform_get_irq(pdev, i);
+
+ /* Parse rx queue interrupt number from device tree
+ * Here we are setting j to point to the point where we
+ * left tx interrupt parsing(i.e 16) and run run the loop
+ * from 0 to 7 to parse rx interrupt number.
+ */
+ for (i = 0, j = edma_cinfo->num_tx_queues, k = 0;
+ i < edma_cinfo->num_rx_queues; i++) {
+ edma_cinfo->rx_irq[k] = platform_get_irq(pdev, j);
+ k += ((num_rxq == 4) ? 2 : 1);
+ j += ((num_rxq == 4) ? 2 : 1);
+ }
+
+ edma_cinfo->rx_head_buffer_len = edma_cinfo->hw.rx_head_buff_size;
+ edma_cinfo->rx_page_buffer_len = PAGE_SIZE;
+
+ err = edma_alloc_queues_tx(edma_cinfo);
+ if (err) {
+ dev_err(&pdev->dev, "Allocation of TX queue failed\n");
+ goto err_tx_qinit;
+ }
+
+ err = edma_alloc_queues_rx(edma_cinfo);
+ if (err) {
+ dev_err(&pdev->dev, "Allocation of RX queue failed\n");
+ goto err_rx_qinit;
+ }
+
+ err = edma_alloc_tx_rings(edma_cinfo);
+ if (err) {
+ dev_err(&pdev->dev, "Allocation of TX resources failed\n");
+ goto err_tx_rinit;
+ }
+
+ err = edma_alloc_rx_rings(edma_cinfo);
+ if (err) {
+ dev_err(&pdev->dev, "Allocation of RX resources failed\n");
+ goto err_rx_rinit;
+ }
+
+ /* Initialize netdev and netdev bitmap for transmit descriptor rings */
+ for (i = 0; i < edma_cinfo->num_tx_queues; i++) {
+ struct edma_tx_desc_ring *etdr = edma_cinfo->tpd_ring[i];
+ int j;
+
+ etdr->netdev_bmp = 0;
+ for (j = 0; j < EDMA_MAX_NETDEV_PER_QUEUE; j++) {
+ etdr->netdev[j] = NULL;
+ etdr->nq[j] = NULL;
+ }
+ }
+
+ if (of_property_read_bool(np, "qcom,mdio_supported")) {
+ mdio_node = of_find_compatible_node(NULL, NULL,
+ "qcom,ipq4019-mdio");
+ if (!mdio_node) {
+ dev_err(&pdev->dev, "cannot find mdio node by phandle");
+ err = -EIO;
+ goto err_mdiobus_init_fail;
+ }
+
+ mdio_plat = of_find_device_by_node(mdio_node);
+ if (!mdio_plat) {
+ dev_err(&pdev->dev,
+ "cannot find platform device from mdio node");
+ of_node_put(mdio_node);
+ err = -EIO;
+ goto err_mdiobus_init_fail;
+ }
+
+ mdio_data = dev_get_drvdata(&mdio_plat->dev);
+ if (!mdio_data) {
+ dev_err(&pdev->dev,
+ "cannot get mii bus reference from device data");
+ of_node_put(mdio_node);
+ err = -EIO;
+ goto err_mdiobus_init_fail;
+ }
+
+ miibus = mdio_data->mii_bus;
+ }
+
+ if (of_property_read_bool(np, "qcom,single-phy") &&
+ edma_cinfo->num_gmac == 1) {
+ err = ess_parse(edma_cinfo);
+ if (!err)
+ err = ess_reset(edma_cinfo);
+ if (err)
+ goto err_single_phy_init;
+ else
+ edma_cinfo->is_single_phy = true;
+ }
+
+ for_each_available_child_of_node(np, pnp) {
+ const char *mac_addr;
+
+ /* this check is needed if parent and daughter dts have
+ * different number of gmac nodes
+ */
+ if (idx_mac == edma_cinfo->num_gmac) {
+ of_node_put(np);
+ break;
+ }
+
+ mac_addr = of_get_mac_address(pnp);
+ if (mac_addr)
+ memcpy(edma_netdev[idx_mac]->dev_addr, mac_addr, ETH_ALEN);
+
+ idx_mac++;
+ }
+
+ /* Populate the adapter structure register the netdevice */
+ for (i = 0; i < edma_cinfo->num_gmac; i++) {
+ int k, m;
+
+ adapter[i] = netdev_priv(edma_netdev[i]);
+ adapter[i]->netdev = edma_netdev[i];
+ adapter[i]->pdev = pdev;
+ for (j = 0; j < CONFIG_NR_CPUS; j++) {
+ m = i % 2;
+ adapter[i]->tx_start_offset[j] =
+ ((j << EDMA_TX_CPU_START_SHIFT) + (m << 1));
+ /* Share the queues with available net-devices.
+ * For instance , with 5 net-devices
+ * eth0/eth2/eth4 will share q0,q1,q4,q5,q8,q9,q12,q13
+ * and eth1/eth3 will get the remaining.
+ */
+ for (k = adapter[i]->tx_start_offset[j]; k <
+ (adapter[i]->tx_start_offset[j] + 2); k++) {
+ if (edma_fill_netdev(edma_cinfo, k, i, j)) {
+ pr_err("Netdev overflow Error\n");
+ goto err_register;
+ }
+ }
+ }
+
+ adapter[i]->edma_cinfo = edma_cinfo;
+ edma_netdev[i]->netdev_ops = &edma_axi_netdev_ops;
+ edma_netdev[i]->max_mtu = 9000;
+ edma_netdev[i]->features = NETIF_F_HW_CSUM | NETIF_F_RXCSUM
+ | NETIF_F_HW_VLAN_CTAG_TX
+ | NETIF_F_HW_VLAN_CTAG_RX | NETIF_F_SG |
+ NETIF_F_TSO | NETIF_F_TSO6 | NETIF_F_GRO;
+ edma_netdev[i]->hw_features = NETIF_F_HW_CSUM | NETIF_F_RXCSUM |
+ NETIF_F_HW_VLAN_CTAG_RX
+ | NETIF_F_SG | NETIF_F_TSO | NETIF_F_TSO6 |
+ NETIF_F_GRO;
+ edma_netdev[i]->vlan_features = NETIF_F_HW_CSUM | NETIF_F_SG |
+ NETIF_F_TSO | NETIF_F_TSO6 |
+ NETIF_F_GRO;
+ edma_netdev[i]->wanted_features = NETIF_F_HW_CSUM | NETIF_F_SG |
+ NETIF_F_TSO | NETIF_F_TSO6 |
+ NETIF_F_GRO;
+
+#ifdef CONFIG_RFS_ACCEL
+ edma_netdev[i]->features |= NETIF_F_RXHASH | NETIF_F_NTUPLE;
+ edma_netdev[i]->hw_features |= NETIF_F_RXHASH | NETIF_F_NTUPLE;
+ edma_netdev[i]->vlan_features |= NETIF_F_RXHASH | NETIF_F_NTUPLE;
+ edma_netdev[i]->wanted_features |= NETIF_F_RXHASH | NETIF_F_NTUPLE;
+#endif
+ edma_set_ethtool_ops(edma_netdev[i]);
+
+ /* This just fill in some default MAC address
+ */
+ if (!is_valid_ether_addr(edma_netdev[i]->dev_addr)) {
+ random_ether_addr(edma_netdev[i]->dev_addr);
+ pr_info("EDMA using MAC@ - using");
+ pr_info("%02x:%02x:%02x:%02x:%02x:%02x\n",
+ *(edma_netdev[i]->dev_addr),
+ *(edma_netdev[i]->dev_addr + 1),
+ *(edma_netdev[i]->dev_addr + 2),
+ *(edma_netdev[i]->dev_addr + 3),
+ *(edma_netdev[i]->dev_addr + 4),
+ *(edma_netdev[i]->dev_addr + 5));
+ }
+
+ err = register_netdev(edma_netdev[i]);
+ if (err)
+ goto err_register;
+
+ /* carrier off reporting is important to
+ * ethtool even BEFORE open
+ */
+ netif_carrier_off(edma_netdev[i]);
+
+ /* Allocate reverse irq cpu mapping structure for
+ * receive queues
+ */
+#ifdef CONFIG_RFS_ACCEL
+ edma_netdev[i]->rx_cpu_rmap =
+ alloc_irq_cpu_rmap(EDMA_NETDEV_RX_QUEUE);
+ if (!edma_netdev[i]->rx_cpu_rmap) {
+ err = -ENOMEM;
+ goto err_rmap_alloc_fail;
+ }
+#endif
+ }
+
+ for (i = 0; i < EDMA_MAX_PORTID_BITMAP_INDEX; i++)
+ edma_cinfo->portid_netdev_lookup_tbl[i] = NULL;
+
+ for_each_available_child_of_node(np, pnp) {
+ const uint32_t *vlan_tag = NULL;
+ int len;
+
+ /* this check is needed if parent and daughter dts have
+ * different number of gmac nodes
+ */
+ if (idx == edma_cinfo->num_gmac)
+ break;
+
+ /* Populate port-id to netdev lookup table */
+ vlan_tag = of_get_property(pnp, "vlan_tag", &len);
+ if (!vlan_tag) {
+ pr_err("Vlan tag parsing Failed.\n");
+ goto err_rmap_alloc_fail;
+ }
+
+ adapter[idx]->default_vlan_tag = of_read_number(vlan_tag, 1);
+ vlan_tag++;
+ portid_bmp = of_read_number(vlan_tag, 1);
+ adapter[idx]->dp_bitmap = portid_bmp;
+
+ portid_bmp = portid_bmp >> 1; /* We ignore CPU Port bit 0 */
+ while (portid_bmp) {
+ int port_bit = ffs(portid_bmp);
+
+ if (port_bit > EDMA_MAX_PORTID_SUPPORTED)
+ goto err_rmap_alloc_fail;
+ edma_cinfo->portid_netdev_lookup_tbl[port_bit] =
+ edma_netdev[idx];
+ portid_bmp &= ~(1 << (port_bit - 1));
+ }
+
+ if (!of_property_read_u32(pnp, "qcom,poll_required",
+ &adapter[idx]->poll_required)) {
+ if (adapter[idx]->poll_required) {
+ of_property_read_u32(pnp, "qcom,phy_mdio_addr",
+ &adapter[idx]->phy_mdio_addr);
+ of_property_read_u32(pnp, "qcom,forced_speed",
+ &adapter[idx]->forced_speed);
+ of_property_read_u32(pnp, "qcom,forced_duplex",
+ &adapter[idx]->forced_duplex);
+
+ /* create a phyid using MDIO bus id
+ * and MDIO bus address
+ */
+ snprintf(adapter[idx]->phy_id,
+ MII_BUS_ID_SIZE + 3, PHY_ID_FMT,
+ miibus->id,
+ adapter[idx]->phy_mdio_addr);
+ }
+ } else {
+ adapter[idx]->poll_required = 0;
+ adapter[idx]->forced_speed = SPEED_1000;
+ adapter[idx]->forced_duplex = DUPLEX_FULL;
+ }
+
+ idx++;
+ }
+
+ edma_cinfo->edma_ctl_table_hdr = register_net_sysctl(&init_net,
+ "net/edma",
+ edma_table);
+ if (!edma_cinfo->edma_ctl_table_hdr) {
+ dev_err(&pdev->dev, "edma sysctl table hdr not registered\n");
+ goto err_unregister_sysctl_tbl;
+ }
+
+ /* Disable all 16 Tx and 8 rx irqs */
+ edma_irq_disable(edma_cinfo);
+
+ err = edma_reset(edma_cinfo);
+ if (err) {
+ err = -EIO;
+ goto err_reset;
+ }
+
+ /* populate per_core_info, do a napi_Add, request 16 TX irqs,
+ * 8 RX irqs, do a napi enable
+ */
+ for (i = 0; i < CONFIG_NR_CPUS; i++) {
+ u8 rx_start;
+
+ edma_cinfo->edma_percpu_info[i].napi.state = 0;
+
+ netif_napi_add(edma_netdev[0],
+ &edma_cinfo->edma_percpu_info[i].napi,
+ edma_poll, 64);
+ napi_enable(&edma_cinfo->edma_percpu_info[i].napi);
+ edma_cinfo->edma_percpu_info[i].tx_mask = tx_mask[i];
+ edma_cinfo->edma_percpu_info[i].rx_mask = EDMA_RX_PER_CPU_MASK
+ << (i << EDMA_RX_PER_CPU_MASK_SHIFT);
+ edma_cinfo->edma_percpu_info[i].tx_start = tx_start[i];
+ edma_cinfo->edma_percpu_info[i].rx_start =
+ i << EDMA_RX_CPU_START_SHIFT;
+ rx_start = i << EDMA_RX_CPU_START_SHIFT;
+ edma_cinfo->edma_percpu_info[i].tx_status = 0;
+ edma_cinfo->edma_percpu_info[i].rx_status = 0;
+ edma_cinfo->edma_percpu_info[i].edma_cinfo = edma_cinfo;
+
+ /* Request irq per core */
+ for (j = edma_cinfo->edma_percpu_info[i].tx_start;
+ j < tx_start[i] + 4; j++) {
+ sprintf(&edma_tx_irq[j][0], "edma_eth_tx%d", j);
+ err = request_irq(edma_cinfo->tx_irq[j],
+ edma_interrupt,
+ 0,
+ &edma_tx_irq[j][0],
+ &edma_cinfo->edma_percpu_info[i]);
+ if (err)
+ goto err_reset;
+ }
+
+ for (j = edma_cinfo->edma_percpu_info[i].rx_start;
+ j < (rx_start +
+ ((edma_cinfo->num_rx_queues == 4) ? 1 : 2));
+ j++) {
+ sprintf(&edma_rx_irq[j][0], "edma_eth_rx%d", j);
+ err = request_irq(edma_cinfo->rx_irq[j],
+ edma_interrupt,
+ 0,
+ &edma_rx_irq[j][0],
+ &edma_cinfo->edma_percpu_info[i]);
+ if (err)
+ goto err_reset;
+ }
+
+#ifdef CONFIG_RFS_ACCEL
+ for (j = edma_cinfo->edma_percpu_info[i].rx_start;
+ j < rx_start + 2; j += 2) {
+ err = irq_cpu_rmap_add(edma_netdev[0]->rx_cpu_rmap,
+ edma_cinfo->rx_irq[j]);
+ if (err)
+ goto err_rmap_add_fail;
+ }
+#endif
+ }
+
+ /* Used to clear interrupt status, allocate rx buffer,
+ * configure edma descriptors registers
+ */
+ err = edma_configure(edma_cinfo);
+ if (err) {
+ err = -EIO;
+ goto err_configure;
+ }
+
+ /* Configure RSS indirection table.
+ * 128 hash will be configured in the following
+ * pattern: hash{0,1,2,3} = {Q0,Q2,Q4,Q6} respectively
+ * and so on
+ */
+ for (i = 0; i < EDMA_NUM_IDT; i++)
+ edma_write_reg(EDMA_REG_RSS_IDT(i), EDMA_RSS_IDT_VALUE);
+
+ /* Configure load balance mapping table.
+ * 4 table entry will be configured according to the
+ * following pattern: load_balance{0,1,2,3} = {Q0,Q1,Q3,Q4}
+ * respectively.
+ */
+ edma_write_reg(EDMA_REG_LB_RING, EDMA_LB_REG_VALUE);
+
+ /* Configure Virtual queue for Tx rings
+ * User can also change this value runtime through
+ * a sysctl
+ */
+ edma_write_reg(EDMA_REG_VQ_CTRL0, EDMA_VQ_REG_VALUE);
+ edma_write_reg(EDMA_REG_VQ_CTRL1, EDMA_VQ_REG_VALUE);
+
+ /* Configure Max AXI Burst write size to 128 bytes*/
+ edma_write_reg(EDMA_REG_AXIW_CTRL_MAXWRSIZE,
+ EDMA_AXIW_MAXWRSIZE_VALUE);
+
+ /* Enable All 16 tx and 8 rx irq mask */
+ edma_irq_enable(edma_cinfo);
+ edma_enable_tx_ctrl(&edma_cinfo->hw);
+ edma_enable_rx_ctrl(&edma_cinfo->hw);
+
+ for (i = 0; i < edma_cinfo->num_gmac; i++) {
+ if (adapter[i]->poll_required) {
+ int phy_mode = of_get_phy_mode(np);
+
+ if (phy_mode < 0)
+ phy_mode = PHY_INTERFACE_MODE_SGMII;
+ adapter[i]->phydev =
+ phy_connect(edma_netdev[i],
+ (const char *)adapter[i]->phy_id,
+ &edma_adjust_link,
+ phy_mode);
+ if (IS_ERR(adapter[i]->phydev)) {
+ dev_dbg(&pdev->dev, "PHY attach FAIL");
+ err = -EIO;
+ goto edma_phy_attach_fail;
+ } else {
+ linkmode_set_bit(ETHTOOL_LINK_MODE_Pause_BIT,
+ adapter[i]->phydev->advertising);
+ linkmode_set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
+ adapter[i]->phydev->advertising);
+ linkmode_set_bit(ETHTOOL_LINK_MODE_Pause_BIT,
+ adapter[i]->phydev->supported);
+ linkmode_set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT,
+ adapter[i]->phydev->supported);
+ }
+ } else {
+ adapter[i]->phydev = NULL;
+ }
+ }
+
+ spin_lock_init(&edma_cinfo->stats_lock);
+
+ timer_setup(&edma_cinfo->edma_stats_timer, edma_statistics_timer, 0);
+ mod_timer(&edma_cinfo->edma_stats_timer, jiffies + 1*HZ);
+
+ return 0;
+
+edma_phy_attach_fail:
+ miibus = NULL;
+err_configure:
+#ifdef CONFIG_RFS_ACCEL
+ for (i = 0; i < edma_cinfo->num_gmac; i++) {
+ free_irq_cpu_rmap(adapter[i]->netdev->rx_cpu_rmap);
+ adapter[i]->netdev->rx_cpu_rmap = NULL;
+ }
+#endif
+err_rmap_add_fail:
+ edma_free_irqs(adapter[0]);
+ for (i = 0; i < CONFIG_NR_CPUS; i++)
+ napi_disable(&edma_cinfo->edma_percpu_info[i].napi);
+err_reset:
+err_unregister_sysctl_tbl:
+err_rmap_alloc_fail:
+ for (i = 0; i < edma_cinfo->num_gmac; i++)
+ unregister_netdev(edma_netdev[i]);
+err_register:
+err_single_phy_init:
+ iounmap(edma_cinfo->ess_hw_addr);
+ clk_disable_unprepare(edma_cinfo->ess_clk);
+err_mdiobus_init_fail:
+ edma_free_rx_rings(edma_cinfo);
+err_rx_rinit:
+ edma_free_tx_rings(edma_cinfo);
+err_tx_rinit:
+ edma_free_queues(edma_cinfo);
+err_rx_qinit:
+err_tx_qinit:
+ iounmap(edma_cinfo->hw.hw_addr);
+err_ioremap:
+ for (i = 0; i < edma_cinfo->num_gmac; i++) {
+ if (edma_netdev[i])
+ free_netdev(edma_netdev[i]);
+ }
+err_cinfo:
+ kfree(edma_cinfo);
+err_alloc:
+ return err;
+}
+
+/* edma_axi_remove()
+ * Device Removal Routine
+ *
+ * edma_axi_remove is called by the platform subsystem to alert the driver
+ * that it should release a platform device.
+ */
+static int edma_axi_remove(struct platform_device *pdev)
+{
+ struct edma_adapter *adapter = netdev_priv(edma_netdev[0]);
+ struct edma_common_info *edma_cinfo = adapter->edma_cinfo;
+ struct edma_hw *hw = &edma_cinfo->hw;
+ int i;
+
+ for (i = 0; i < edma_cinfo->num_gmac; i++)
+ unregister_netdev(edma_netdev[i]);
+
+ edma_stop_rx_tx(hw);
+ for (i = 0; i < CONFIG_NR_CPUS; i++)
+ napi_disable(&edma_cinfo->edma_percpu_info[i].napi);
+
+ edma_irq_disable(edma_cinfo);
+ edma_write_reg(EDMA_REG_RX_ISR, 0xff);
+ edma_write_reg(EDMA_REG_TX_ISR, 0xffff);
+#ifdef CONFIG_RFS_ACCEL
+ for (i = 0; i < edma_cinfo->num_gmac; i++) {
+ free_irq_cpu_rmap(edma_netdev[i]->rx_cpu_rmap);
+ edma_netdev[i]->rx_cpu_rmap = NULL;
+ }
+#endif
+
+ for (i = 0; i < edma_cinfo->num_gmac; i++) {
+ struct edma_adapter *adapter = netdev_priv(edma_netdev[i]);
+
+ if (adapter->phydev)
+ phy_disconnect(adapter->phydev);
+ }
+
+ del_timer_sync(&edma_cinfo->edma_stats_timer);
+ edma_free_irqs(adapter);
+ unregister_net_sysctl_table(edma_cinfo->edma_ctl_table_hdr);
+ iounmap(edma_cinfo->ess_hw_addr);
+ clk_disable_unprepare(edma_cinfo->ess_clk);
+ edma_free_tx_resources(edma_cinfo);
+ edma_free_rx_resources(edma_cinfo);
+ edma_free_tx_rings(edma_cinfo);
+ edma_free_rx_rings(edma_cinfo);
+ edma_free_queues(edma_cinfo);
+ for (i = 0; i < edma_cinfo->num_gmac; i++)
+ free_netdev(edma_netdev[i]);
+
+ kfree(edma_cinfo);
+
+ return 0;
+}
+
+static const struct of_device_id edma_of_mtable[] = {
+ {.compatible = "qcom,ess-edma" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, edma_of_mtable);
+
+static struct platform_driver edma_axi_driver = {
+ .driver = {
+ .name = edma_axi_driver_name,
+ .of_match_table = edma_of_mtable,
+ },
+ .probe = edma_axi_probe,
+ .remove = edma_axi_remove,
+};
+
+module_platform_driver(edma_axi_driver);
+
+MODULE_AUTHOR("Qualcomm Atheros Inc");
+MODULE_DESCRIPTION("QCA ESS EDMA driver");
+MODULE_LICENSE("GPL");
--- /dev/null
+/*
+ * Copyright (c) 2015 - 2016, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for
+ * any purpose with or without fee is hereby granted, provided that the
+ * above copyright notice and this permission notice appear in all copies.
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT
+ * OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#include <linux/ethtool.h>
+#include <linux/netdevice.h>
+#include <linux/string.h>
+#include "edma.h"
+
+struct edma_ethtool_stats {
+ uint8_t stat_string[ETH_GSTRING_LEN];
+ uint32_t stat_offset;
+};
+
+#define EDMA_STAT(m) offsetof(struct edma_ethtool_statistics, m)
+#define DRVINFO_LEN 32
+
+/* Array of strings describing statistics
+ */
+static const struct edma_ethtool_stats edma_gstrings_stats[] = {
+ {"tx_q0_pkt", EDMA_STAT(tx_q0_pkt)},
+ {"tx_q1_pkt", EDMA_STAT(tx_q1_pkt)},
+ {"tx_q2_pkt", EDMA_STAT(tx_q2_pkt)},
+ {"tx_q3_pkt", EDMA_STAT(tx_q3_pkt)},
+ {"tx_q4_pkt", EDMA_STAT(tx_q4_pkt)},
+ {"tx_q5_pkt", EDMA_STAT(tx_q5_pkt)},
+ {"tx_q6_pkt", EDMA_STAT(tx_q6_pkt)},
+ {"tx_q7_pkt", EDMA_STAT(tx_q7_pkt)},
+ {"tx_q8_pkt", EDMA_STAT(tx_q8_pkt)},
+ {"tx_q9_pkt", EDMA_STAT(tx_q9_pkt)},
+ {"tx_q10_pkt", EDMA_STAT(tx_q10_pkt)},
+ {"tx_q11_pkt", EDMA_STAT(tx_q11_pkt)},
+ {"tx_q12_pkt", EDMA_STAT(tx_q12_pkt)},
+ {"tx_q13_pkt", EDMA_STAT(tx_q13_pkt)},
+ {"tx_q14_pkt", EDMA_STAT(tx_q14_pkt)},
+ {"tx_q15_pkt", EDMA_STAT(tx_q15_pkt)},
+ {"tx_q0_byte", EDMA_STAT(tx_q0_byte)},
+ {"tx_q1_byte", EDMA_STAT(tx_q1_byte)},
+ {"tx_q2_byte", EDMA_STAT(tx_q2_byte)},
+ {"tx_q3_byte", EDMA_STAT(tx_q3_byte)},
+ {"tx_q4_byte", EDMA_STAT(tx_q4_byte)},
+ {"tx_q5_byte", EDMA_STAT(tx_q5_byte)},
+ {"tx_q6_byte", EDMA_STAT(tx_q6_byte)},
+ {"tx_q7_byte", EDMA_STAT(tx_q7_byte)},
+ {"tx_q8_byte", EDMA_STAT(tx_q8_byte)},
+ {"tx_q9_byte", EDMA_STAT(tx_q9_byte)},
+ {"tx_q10_byte", EDMA_STAT(tx_q10_byte)},
+ {"tx_q11_byte", EDMA_STAT(tx_q11_byte)},
+ {"tx_q12_byte", EDMA_STAT(tx_q12_byte)},
+ {"tx_q13_byte", EDMA_STAT(tx_q13_byte)},
+ {"tx_q14_byte", EDMA_STAT(tx_q14_byte)},
+ {"tx_q15_byte", EDMA_STAT(tx_q15_byte)},
+ {"rx_q0_pkt", EDMA_STAT(rx_q0_pkt)},
+ {"rx_q1_pkt", EDMA_STAT(rx_q1_pkt)},
+ {"rx_q2_pkt", EDMA_STAT(rx_q2_pkt)},
+ {"rx_q3_pkt", EDMA_STAT(rx_q3_pkt)},
+ {"rx_q4_pkt", EDMA_STAT(rx_q4_pkt)},
+ {"rx_q5_pkt", EDMA_STAT(rx_q5_pkt)},
+ {"rx_q6_pkt", EDMA_STAT(rx_q6_pkt)},
+ {"rx_q7_pkt", EDMA_STAT(rx_q7_pkt)},
+ {"rx_q0_byte", EDMA_STAT(rx_q0_byte)},
+ {"rx_q1_byte", EDMA_STAT(rx_q1_byte)},
+ {"rx_q2_byte", EDMA_STAT(rx_q2_byte)},
+ {"rx_q3_byte", EDMA_STAT(rx_q3_byte)},
+ {"rx_q4_byte", EDMA_STAT(rx_q4_byte)},
+ {"rx_q5_byte", EDMA_STAT(rx_q5_byte)},
+ {"rx_q6_byte", EDMA_STAT(rx_q6_byte)},
+ {"rx_q7_byte", EDMA_STAT(rx_q7_byte)},
+ {"tx_desc_error", EDMA_STAT(tx_desc_error)},
+ {"rx_alloc_fail_ctr", EDMA_STAT(rx_alloc_fail_ctr)},
+};
+
+#define EDMA_STATS_LEN ARRAY_SIZE(edma_gstrings_stats)
+
+/* edma_get_strset_count()
+ * Get strset count
+ */
+static int edma_get_strset_count(struct net_device *netdev,
+ int sset)
+{
+ switch (sset) {
+ case ETH_SS_STATS:
+ return EDMA_STATS_LEN;
+ default:
+ netdev_dbg(netdev, "%s: Invalid string set", __func__);
+ return -EOPNOTSUPP;
+ }
+}
+
+
+/* edma_get_strings()
+ * get stats string
+ */
+static void edma_get_strings(struct net_device *netdev, uint32_t stringset,
+ uint8_t *data)
+{
+ uint8_t *p = data;
+ uint32_t i;
+
+ switch (stringset) {
+ case ETH_SS_STATS:
+ for (i = 0; i < EDMA_STATS_LEN; i++) {
+ memcpy(p, edma_gstrings_stats[i].stat_string,
+ min((size_t)ETH_GSTRING_LEN,
+ strlen(edma_gstrings_stats[i].stat_string)
+ + 1));
+ p += ETH_GSTRING_LEN;
+ }
+ break;
+ }
+}
+
+/* edma_get_ethtool_stats()
+ * Get ethtool statistics
+ */
+static void edma_get_ethtool_stats(struct net_device *netdev,
+ struct ethtool_stats *stats, uint64_t *data)
+{
+ struct edma_adapter *adapter = netdev_priv(netdev);
+ struct edma_common_info *edma_cinfo = adapter->edma_cinfo;
+ int i;
+ uint8_t *p = NULL;
+
+ edma_read_append_stats(edma_cinfo);
+
+ for(i = 0; i < EDMA_STATS_LEN; i++) {
+ p = (uint8_t *)&(edma_cinfo->edma_ethstats) +
+ edma_gstrings_stats[i].stat_offset;
+ data[i] = *(uint32_t *)p;
+ }
+}
+
+/* edma_get_drvinfo()
+ * get edma driver info
+ */
+static void edma_get_drvinfo(struct net_device *dev,
+ struct ethtool_drvinfo *info)
+{
+ strlcpy(info->driver, "ess_edma", DRVINFO_LEN);
+ strlcpy(info->bus_info, "axi", ETHTOOL_BUSINFO_LEN);
+}
+
+/* edma_nway_reset()
+ * Reset the phy, if available.
+ */
+static int edma_nway_reset(struct net_device *netdev)
+{
+ return -EINVAL;
+}
+
+/* edma_get_wol()
+ * get wake on lan info
+ */
+static void edma_get_wol(struct net_device *netdev,
+ struct ethtool_wolinfo *wol)
+{
+ wol->supported = 0;
+ wol->wolopts = 0;
+}
+
+/* edma_get_msglevel()
+ * get message level.
+ */
+static uint32_t edma_get_msglevel(struct net_device *netdev)
+{
+ return 0;
+}
+
+/* edma_get_settings()
+ * Get edma settings
+ */
+#if 0
+static int edma_get_settings(struct net_device *netdev,
+ struct ethtool_cmd *ecmd)
+{
+ struct edma_adapter *adapter = netdev_priv(netdev);
+
+ if (adapter->poll_required) {
+ struct phy_device *phydev = NULL;
+ uint16_t phyreg;
+
+ if ((adapter->forced_speed != SPEED_UNKNOWN)
+ && !(adapter->poll_required))
+ return -EPERM;
+
+ phydev = adapter->phydev;
+
+ ecmd->advertising = phydev->advertising;
+ ecmd->autoneg = phydev->autoneg;
+
+ if (adapter->link_state == __EDMA_LINKDOWN) {
+ ecmd->speed = SPEED_UNKNOWN;
+ ecmd->duplex = DUPLEX_UNKNOWN;
+ } else {
+ ecmd->speed = phydev->speed;
+ ecmd->duplex = phydev->duplex;
+ }
+
+ ecmd->phy_address = adapter->phy_mdio_addr;
+
+ phyreg = (uint16_t)phy_read(adapter->phydev, MII_LPA);
+ if (phyreg & LPA_10HALF)
+ ecmd->lp_advertising |= ADVERTISED_10baseT_Half;
+
+ if (phyreg & LPA_10FULL)
+ ecmd->lp_advertising |= ADVERTISED_10baseT_Full;
+
+ if (phyreg & LPA_100HALF)
+ ecmd->lp_advertising |= ADVERTISED_100baseT_Half;
+
+ if (phyreg & LPA_100FULL)
+ ecmd->lp_advertising |= ADVERTISED_100baseT_Full;
+
+ phyreg = (uint16_t)phy_read(adapter->phydev, MII_STAT1000);
+ if (phyreg & LPA_1000HALF)
+ ecmd->lp_advertising |= ADVERTISED_1000baseT_Half;
+
+ if (phyreg & LPA_1000FULL)
+ ecmd->lp_advertising |= ADVERTISED_1000baseT_Full;
+ } else {
+ /* If the speed/duplex for this GMAC is forced and we
+ * are not polling for link state changes, return the
+ * values as specified by platform. This will be true
+ * for GMACs connected to switch, and interfaces that
+ * do not use a PHY.
+ */
+ if (!(adapter->poll_required)) {
+ if (adapter->forced_speed != SPEED_UNKNOWN) {
+ /* set speed and duplex */
+ ethtool_cmd_speed_set(ecmd, SPEED_1000);
+ ecmd->duplex = DUPLEX_FULL;
+
+ /* Populate capabilities advertised by self */
+ ecmd->advertising = 0;
+ ecmd->autoneg = 0;
+ ecmd->port = PORT_TP;
+ ecmd->transceiver = XCVR_EXTERNAL;
+ } else {
+ /* non link polled and non
+ * forced speed/duplex interface
+ */
+ return -EIO;
+ }
+ }
+ }
+
+ return 0;
+}
+
+/* edma_set_settings()
+ * Set EDMA settings
+ */
+static int edma_set_settings(struct net_device *netdev,
+ struct ethtool_cmd *ecmd)
+{
+ struct edma_adapter *adapter = netdev_priv(netdev);
+ struct phy_device *phydev = NULL;
+
+ if ((adapter->forced_speed != SPEED_UNKNOWN) &&
+ !adapter->poll_required)
+ return -EPERM;
+
+ phydev = adapter->phydev;
+ phydev->advertising = ecmd->advertising;
+ phydev->autoneg = ecmd->autoneg;
+ phydev->speed = ethtool_cmd_speed(ecmd);
+ phydev->duplex = ecmd->duplex;
+
+ genphy_config_aneg(phydev);
+
+ return 0;
+}
+#endif
+
+/* edma_get_coalesce
+ * get interrupt mitigation
+ */
+static int edma_get_coalesce(struct net_device *netdev,
+ struct ethtool_coalesce *ec)
+{
+ u32 reg_val;
+
+ edma_get_tx_rx_coalesce(®_val);
+
+ /* We read the Interrupt Moderation Timer(IMT) register value,
+ * use lower 16 bit for rx and higher 16 bit for Tx. We do a
+ * left shift by 1, because IMT resolution timer is 2usecs.
+ * Hence the value given by the register is multiplied by 2 to
+ * get the actual time in usecs.
+ */
+ ec->tx_coalesce_usecs = (((reg_val >> 16) & 0xffff) << 1);
+ ec->rx_coalesce_usecs = ((reg_val & 0xffff) << 1);
+
+ return 0;
+}
+
+/* edma_set_coalesce
+ * set interrupt mitigation
+ */
+static int edma_set_coalesce(struct net_device *netdev,
+ struct ethtool_coalesce *ec)
+{
+ if (ec->tx_coalesce_usecs)
+ edma_change_tx_coalesce(ec->tx_coalesce_usecs);
+ if (ec->rx_coalesce_usecs)
+ edma_change_rx_coalesce(ec->rx_coalesce_usecs);
+
+ return 0;
+}
+
+/* edma_set_priv_flags()
+ * Set EDMA private flags
+ */
+static int edma_set_priv_flags(struct net_device *netdev, u32 flags)
+{
+ return 0;
+}
+
+/* edma_get_priv_flags()
+ * get edma driver flags
+ */
+static u32 edma_get_priv_flags(struct net_device *netdev)
+{
+ return 0;
+}
+
+/* edma_get_ringparam()
+ * get ring size
+ */
+static void edma_get_ringparam(struct net_device *netdev,
+ struct ethtool_ringparam *ring)
+{
+ struct edma_adapter *adapter = netdev_priv(netdev);
+ struct edma_common_info *edma_cinfo = adapter->edma_cinfo;
+
+ ring->tx_max_pending = edma_cinfo->tx_ring_count;
+ ring->rx_max_pending = edma_cinfo->rx_ring_count;
+}
+
+/* Ethtool operations
+ */
+static const struct ethtool_ops edma_ethtool_ops = {
+ .get_drvinfo = &edma_get_drvinfo,
+ .get_link = ðtool_op_get_link,
+ .get_msglevel = &edma_get_msglevel,
+ .nway_reset = &edma_nway_reset,
+ .get_wol = &edma_get_wol,
+// .get_settings = &edma_get_settings,
+// .set_settings = &edma_set_settings,
+ .get_strings = &edma_get_strings,
+ .get_sset_count = &edma_get_strset_count,
+ .get_ethtool_stats = &edma_get_ethtool_stats,
+ .get_coalesce = &edma_get_coalesce,
+ .set_coalesce = &edma_set_coalesce,
+ .get_priv_flags = edma_get_priv_flags,
+ .set_priv_flags = edma_set_priv_flags,
+ .get_ringparam = edma_get_ringparam,
+};
+
+/* edma_set_ethtool_ops
+ * Set ethtool operations
+ */
+void edma_set_ethtool_ops(struct net_device *netdev)
+{
+ netdev->ethtool_ops = &edma_ethtool_ops;
+}
--- /dev/null
+/*
+ * Copyright (c) 2014 - 2016, The Linux Foundation. All rights reserved.
+ *
+ * Permission to use, copy, modify, and/or distribute this software for
+ * any purpose with or without fee is hereby granted, provided that the
+ * above copyright notice and this permission notice appear in all copies.
+ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
+ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
+ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
+ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
+ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT
+ * OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
+ */
+
+#ifndef _ESS_EDMA_H_
+#define _ESS_EDMA_H_
+
+#include <linux/types.h>
+
+struct edma_adapter;
+struct edma_hw;
+
+/* register definition */
+#define EDMA_REG_MAS_CTRL 0x0
+#define EDMA_REG_TIMEOUT_CTRL 0x004
+#define EDMA_REG_DBG0 0x008
+#define EDMA_REG_DBG1 0x00C
+#define EDMA_REG_SW_CTRL0 0x100
+#define EDMA_REG_SW_CTRL1 0x104
+
+/* Interrupt Status Register */
+#define EDMA_REG_RX_ISR 0x200
+#define EDMA_REG_TX_ISR 0x208
+#define EDMA_REG_MISC_ISR 0x210
+#define EDMA_REG_WOL_ISR 0x218
+
+#define EDMA_MISC_ISR_RX_URG_Q(x) (1 << x)
+
+#define EDMA_MISC_ISR_AXIR_TIMEOUT 0x00000100
+#define EDMA_MISC_ISR_AXIR_ERR 0x00000200
+#define EDMA_MISC_ISR_TXF_DEAD 0x00000400
+#define EDMA_MISC_ISR_AXIW_ERR 0x00000800
+#define EDMA_MISC_ISR_AXIW_TIMEOUT 0x00001000
+
+#define EDMA_WOL_ISR 0x00000001
+
+/* Interrupt Mask Register */
+#define EDMA_REG_MISC_IMR 0x214
+#define EDMA_REG_WOL_IMR 0x218
+
+#define EDMA_RX_IMR_NORMAL_MASK 0x1
+#define EDMA_TX_IMR_NORMAL_MASK 0x1
+#define EDMA_MISC_IMR_NORMAL_MASK 0x80001FFF
+#define EDMA_WOL_IMR_NORMAL_MASK 0x1
+
+/* Edma receive consumer index */
+#define EDMA_REG_RX_SW_CONS_IDX_Q(x) (0x220 + ((x) << 2)) /* x is the queue id */
+/* Edma transmit consumer index */
+#define EDMA_REG_TX_SW_CONS_IDX_Q(x) (0x240 + ((x) << 2)) /* x is the queue id */
+
+/* IRQ Moderator Initial Timer Register */
+#define EDMA_REG_IRQ_MODRT_TIMER_INIT 0x280
+#define EDMA_IRQ_MODRT_TIMER_MASK 0xFFFF
+#define EDMA_IRQ_MODRT_RX_TIMER_SHIFT 0
+#define EDMA_IRQ_MODRT_TX_TIMER_SHIFT 16
+
+/* Interrupt Control Register */
+#define EDMA_REG_INTR_CTRL 0x284
+#define EDMA_INTR_CLR_TYP_SHIFT 0
+#define EDMA_INTR_SW_IDX_W_TYP_SHIFT 1
+#define EDMA_INTR_CLEAR_TYPE_W1 0
+#define EDMA_INTR_CLEAR_TYPE_R 1
+
+/* RX Interrupt Mask Register */
+#define EDMA_REG_RX_INT_MASK_Q(x) (0x300 + ((x) << 2)) /* x = queue id */
+
+/* TX Interrupt mask register */
+#define EDMA_REG_TX_INT_MASK_Q(x) (0x340 + ((x) << 2)) /* x = queue id */
+
+/* Load Ptr Register
+ * Software sets this bit after the initialization of the head and tail
+ */
+#define EDMA_REG_TX_SRAM_PART 0x400
+#define EDMA_LOAD_PTR_SHIFT 16
+
+/* TXQ Control Register */
+#define EDMA_REG_TXQ_CTRL 0x404
+#define EDMA_TXQ_CTRL_IP_OPTION_EN 0x10
+#define EDMA_TXQ_CTRL_TXQ_EN 0x20
+#define EDMA_TXQ_CTRL_ENH_MODE 0x40
+#define EDMA_TXQ_CTRL_LS_8023_EN 0x80
+#define EDMA_TXQ_CTRL_TPD_BURST_EN 0x100
+#define EDMA_TXQ_CTRL_LSO_BREAK_EN 0x200
+#define EDMA_TXQ_NUM_TPD_BURST_MASK 0xF
+#define EDMA_TXQ_TXF_BURST_NUM_MASK 0xFFFF
+#define EDMA_TXQ_NUM_TPD_BURST_SHIFT 0
+#define EDMA_TXQ_TXF_BURST_NUM_SHIFT 16
+
+#define EDMA_REG_TXF_WATER_MARK 0x408 /* In 8-bytes */
+#define EDMA_TXF_WATER_MARK_MASK 0x0FFF
+#define EDMA_TXF_LOW_WATER_MARK_SHIFT 0
+#define EDMA_TXF_HIGH_WATER_MARK_SHIFT 16
+#define EDMA_TXQ_CTRL_BURST_MODE_EN 0x80000000
+
+/* WRR Control Register */
+#define EDMA_REG_WRR_CTRL_Q0_Q3 0x40c
+#define EDMA_REG_WRR_CTRL_Q4_Q7 0x410
+#define EDMA_REG_WRR_CTRL_Q8_Q11 0x414
+#define EDMA_REG_WRR_CTRL_Q12_Q15 0x418
+
+/* Weight round robin(WRR), it takes queue as input, and computes
+ * starting bits where we need to write the weight for a particular
+ * queue
+ */
+#define EDMA_WRR_SHIFT(x) (((x) * 5) % 20)
+
+/* Tx Descriptor Control Register */
+#define EDMA_REG_TPD_RING_SIZE 0x41C
+#define EDMA_TPD_RING_SIZE_SHIFT 0
+#define EDMA_TPD_RING_SIZE_MASK 0xFFFF
+
+/* Transmit descriptor base address */
+#define EDMA_REG_TPD_BASE_ADDR_Q(x) (0x420 + ((x) << 2)) /* x = queue id */
+
+/* TPD Index Register */
+#define EDMA_REG_TPD_IDX_Q(x) (0x460 + ((x) << 2)) /* x = queue id */
+
+#define EDMA_TPD_PROD_IDX_BITS 0x0000FFFF
+#define EDMA_TPD_CONS_IDX_BITS 0xFFFF0000
+#define EDMA_TPD_PROD_IDX_MASK 0xFFFF
+#define EDMA_TPD_CONS_IDX_MASK 0xFFFF
+#define EDMA_TPD_PROD_IDX_SHIFT 0
+#define EDMA_TPD_CONS_IDX_SHIFT 16
+
+/* TX Virtual Queue Mapping Control Register */
+#define EDMA_REG_VQ_CTRL0 0x4A0
+#define EDMA_REG_VQ_CTRL1 0x4A4
+
+/* Virtual QID shift, it takes queue as input, and computes
+ * Virtual QID position in virtual qid control register
+ */
+#define EDMA_VQ_ID_SHIFT(i) (((i) * 3) % 24)
+
+/* Virtual Queue Default Value */
+#define EDMA_VQ_REG_VALUE 0x240240
+
+/* Tx side Port Interface Control Register */
+#define EDMA_REG_PORT_CTRL 0x4A8
+#define EDMA_PAD_EN_SHIFT 15
+
+/* Tx side VLAN Configuration Register */
+#define EDMA_REG_VLAN_CFG 0x4AC
+
+#define EDMA_TX_CVLAN 16
+#define EDMA_TX_INS_CVLAN 17
+#define EDMA_TX_CVLAN_TAG_SHIFT 0
+
+#define EDMA_TX_SVLAN 14
+#define EDMA_TX_INS_SVLAN 15
+#define EDMA_TX_SVLAN_TAG_SHIFT 16
+
+/* Tx Queue Packet Statistic Register */
+#define EDMA_REG_TX_STAT_PKT_Q(x) (0x700 + ((x) << 3)) /* x = queue id */
+
+#define EDMA_TX_STAT_PKT_MASK 0xFFFFFF
+
+/* Tx Queue Byte Statistic Register */
+#define EDMA_REG_TX_STAT_BYTE_Q(x) (0x704 + ((x) << 3)) /* x = queue id */
+
+/* Load Balance Based Ring Offset Register */
+#define EDMA_REG_LB_RING 0x800
+#define EDMA_LB_RING_ENTRY_MASK 0xff
+#define EDMA_LB_RING_ID_MASK 0x7
+#define EDMA_LB_RING_PROFILE_ID_MASK 0x3
+#define EDMA_LB_RING_ENTRY_BIT_OFFSET 8
+#define EDMA_LB_RING_ID_OFFSET 0
+#define EDMA_LB_RING_PROFILE_ID_OFFSET 3
+#define EDMA_LB_REG_VALUE 0x6040200
+
+/* Load Balance Priority Mapping Register */
+#define EDMA_REG_LB_PRI_START 0x804
+#define EDMA_REG_LB_PRI_END 0x810
+#define EDMA_LB_PRI_REG_INC 4
+#define EDMA_LB_PRI_ENTRY_BIT_OFFSET 4
+#define EDMA_LB_PRI_ENTRY_MASK 0xf
+
+/* RSS Priority Mapping Register */
+#define EDMA_REG_RSS_PRI 0x820
+#define EDMA_RSS_PRI_ENTRY_MASK 0xf
+#define EDMA_RSS_RING_ID_MASK 0x7
+#define EDMA_RSS_PRI_ENTRY_BIT_OFFSET 4
+
+/* RSS Indirection Register */
+#define EDMA_REG_RSS_IDT(x) (0x840 + ((x) << 2)) /* x = No. of indirection table */
+#define EDMA_NUM_IDT 16
+#define EDMA_RSS_IDT_VALUE 0x64206420
+
+/* Default RSS Ring Register */
+#define EDMA_REG_DEF_RSS 0x890
+#define EDMA_DEF_RSS_MASK 0x7
+
+/* RSS Hash Function Type Register */
+#define EDMA_REG_RSS_TYPE 0x894
+#define EDMA_RSS_TYPE_NONE 0x01
+#define EDMA_RSS_TYPE_IPV4TCP 0x02
+#define EDMA_RSS_TYPE_IPV6_TCP 0x04
+#define EDMA_RSS_TYPE_IPV4_UDP 0x08
+#define EDMA_RSS_TYPE_IPV6UDP 0x10
+#define EDMA_RSS_TYPE_IPV4 0x20
+#define EDMA_RSS_TYPE_IPV6 0x40
+#define EDMA_RSS_HASH_MODE_MASK 0x7f
+
+#define EDMA_REG_RSS_HASH_VALUE 0x8C0
+
+#define EDMA_REG_RSS_TYPE_RESULT 0x8C4
+
+#define EDMA_HASH_TYPE_START 0
+#define EDMA_HASH_TYPE_END 5
+#define EDMA_HASH_TYPE_SHIFT 12
+
+#define EDMA_RFS_FLOW_ENTRIES 1024
+#define EDMA_RFS_FLOW_ENTRIES_MASK (EDMA_RFS_FLOW_ENTRIES - 1)
+#define EDMA_RFS_EXPIRE_COUNT_PER_CALL 128
+
+/* RFD Base Address Register */
+#define EDMA_REG_RFD_BASE_ADDR_Q(x) (0x950 + ((x) << 2)) /* x = queue id */
+
+/* RFD Index Register */
+#define EDMA_REG_RFD_IDX_Q(x) (0x9B0 + ((x) << 2))
+
+#define EDMA_RFD_PROD_IDX_BITS 0x00000FFF
+#define EDMA_RFD_CONS_IDX_BITS 0x0FFF0000
+#define EDMA_RFD_PROD_IDX_MASK 0xFFF
+#define EDMA_RFD_CONS_IDX_MASK 0xFFF
+#define EDMA_RFD_PROD_IDX_SHIFT 0
+#define EDMA_RFD_CONS_IDX_SHIFT 16
+
+/* Rx Descriptor Control Register */
+#define EDMA_REG_RX_DESC0 0xA10
+#define EDMA_RFD_RING_SIZE_MASK 0xFFF
+#define EDMA_RX_BUF_SIZE_MASK 0xFFFF
+#define EDMA_RFD_RING_SIZE_SHIFT 0
+#define EDMA_RX_BUF_SIZE_SHIFT 16
+
+#define EDMA_REG_RX_DESC1 0xA14
+#define EDMA_RXQ_RFD_BURST_NUM_MASK 0x3F
+#define EDMA_RXQ_RFD_PF_THRESH_MASK 0x1F
+#define EDMA_RXQ_RFD_LOW_THRESH_MASK 0xFFF
+#define EDMA_RXQ_RFD_BURST_NUM_SHIFT 0
+#define EDMA_RXQ_RFD_PF_THRESH_SHIFT 8
+#define EDMA_RXQ_RFD_LOW_THRESH_SHIFT 16
+
+/* RXQ Control Register */
+#define EDMA_REG_RXQ_CTRL 0xA18
+#define EDMA_FIFO_THRESH_TYPE_SHIF 0
+#define EDMA_FIFO_THRESH_128_BYTE 0x0
+#define EDMA_FIFO_THRESH_64_BYTE 0x1
+#define EDMA_RXQ_CTRL_RMV_VLAN 0x00000002
+#define EDMA_RXQ_CTRL_EN 0x0000FF00
+
+/* AXI Burst Size Config */
+#define EDMA_REG_AXIW_CTRL_MAXWRSIZE 0xA1C
+#define EDMA_AXIW_MAXWRSIZE_VALUE 0x0
+
+/* Rx Statistics Register */
+#define EDMA_REG_RX_STAT_BYTE_Q(x) (0xA30 + ((x) << 2)) /* x = queue id */
+#define EDMA_REG_RX_STAT_PKT_Q(x) (0xA50 + ((x) << 2)) /* x = queue id */
+
+/* WoL Pattern Length Register */
+#define EDMA_REG_WOL_PATTERN_LEN0 0xC00
+#define EDMA_WOL_PT_LEN_MASK 0xFF
+#define EDMA_WOL_PT0_LEN_SHIFT 0
+#define EDMA_WOL_PT1_LEN_SHIFT 8
+#define EDMA_WOL_PT2_LEN_SHIFT 16
+#define EDMA_WOL_PT3_LEN_SHIFT 24
+
+#define EDMA_REG_WOL_PATTERN_LEN1 0xC04
+#define EDMA_WOL_PT4_LEN_SHIFT 0
+#define EDMA_WOL_PT5_LEN_SHIFT 8
+#define EDMA_WOL_PT6_LEN_SHIFT 16
+
+/* WoL Control Register */
+#define EDMA_REG_WOL_CTRL 0xC08
+#define EDMA_WOL_WK_EN 0x00000001
+#define EDMA_WOL_MG_EN 0x00000002
+#define EDMA_WOL_PT0_EN 0x00000004
+#define EDMA_WOL_PT1_EN 0x00000008
+#define EDMA_WOL_PT2_EN 0x00000010
+#define EDMA_WOL_PT3_EN 0x00000020
+#define EDMA_WOL_PT4_EN 0x00000040
+#define EDMA_WOL_PT5_EN 0x00000080
+#define EDMA_WOL_PT6_EN 0x00000100
+
+/* MAC Control Register */
+#define EDMA_REG_MAC_CTRL0 0xC20
+#define EDMA_REG_MAC_CTRL1 0xC24
+
+/* WoL Pattern Register */
+#define EDMA_REG_WOL_PATTERN_START 0x5000
+#define EDMA_PATTERN_PART_REG_OFFSET 0x40
+
+
+/* TX descriptor fields */
+#define EDMA_TPD_HDR_SHIFT 0
+#define EDMA_TPD_PPPOE_EN 0x00000100
+#define EDMA_TPD_IP_CSUM_EN 0x00000200
+#define EDMA_TPD_TCP_CSUM_EN 0x0000400
+#define EDMA_TPD_UDP_CSUM_EN 0x00000800
+#define EDMA_TPD_CUSTOM_CSUM_EN 0x00000C00
+#define EDMA_TPD_LSO_EN 0x00001000
+#define EDMA_TPD_LSO_V2_EN 0x00002000
+#define EDMA_TPD_IPV4_EN 0x00010000
+#define EDMA_TPD_MSS_MASK 0x1FFF
+#define EDMA_TPD_MSS_SHIFT 18
+#define EDMA_TPD_CUSTOM_CSUM_SHIFT 18
+
+/* RRD descriptor fields */
+#define EDMA_RRD_NUM_RFD_MASK 0x000F
+#define EDMA_RRD_SVLAN 0x8000
+#define EDMA_RRD_FLOW_COOKIE_MASK 0x07FF;
+
+#define EDMA_RRD_PKT_SIZE_MASK 0x3FFF
+#define EDMA_RRD_CSUM_FAIL_MASK 0xC000
+#define EDMA_RRD_CVLAN 0x0001
+#define EDMA_RRD_DESC_VALID 0x8000
+
+#define EDMA_RRD_PRIORITY_SHIFT 4
+#define EDMA_RRD_PRIORITY_MASK 0x7
+#define EDMA_RRD_PORT_TYPE_SHIFT 7
+#define EDMA_RRD_PORT_TYPE_MASK 0x1F
+
+#define ESS_RGMII_CTRL 0x0004
+
+/* Port status registers */
+#define ESS_PORT0_STATUS 0x007C
+#define ESS_PORT1_STATUS 0x0080
+#define ESS_PORT2_STATUS 0x0084
+#define ESS_PORT3_STATUS 0x0088
+#define ESS_PORT4_STATUS 0x008C
+#define ESS_PORT5_STATUS 0x0090
+
+#define ESS_PORT_STATUS_HDX_FLOW_CTL 0x80
+#define ESS_PORT_STATUS_DUPLEX_MODE 0x40
+#define ESS_PORT_STATUS_RX_FLOW_EN 0x20
+#define ESS_PORT_STATUS_TX_FLOW_EN 0x10
+#define ESS_PORT_STATUS_RX_MAC_EN 0x08
+#define ESS_PORT_STATUS_TX_MAC_EN 0x04
+#define ESS_PORT_STATUS_SPEED_INV 0x03
+#define ESS_PORT_STATUS_SPEED_1000 0x02
+#define ESS_PORT_STATUS_SPEED_100 0x01
+#define ESS_PORT_STATUS_SPEED_10 0x00
+
+#define ESS_PORT_1G_FDX (ESS_PORT_STATUS_DUPLEX_MODE | ESS_PORT_STATUS_RX_FLOW_EN | \
+ ESS_PORT_STATUS_TX_FLOW_EN | ESS_PORT_STATUS_RX_MAC_EN | \
+ ESS_PORT_STATUS_TX_MAC_EN | ESS_PORT_STATUS_SPEED_1000)
+
+#define PHY_STATUS_REG 0x11
+#define PHY_STATUS_SPEED 0xC000
+#define PHY_STATUS_SPEED_SHIFT 14
+#define PHY_STATUS_DUPLEX 0x2000
+#define PHY_STATUS_DUPLEX_SHIFT 13
+#define PHY_STATUS_SPEED_DUPLEX_RESOLVED 0x0800
+#define PHY_STATUS_CARRIER 0x0400
+#define PHY_STATUS_CARRIER_SHIFT 10
+
+/* Port lookup control registers */
+#define ESS_PORT0_LOOKUP_CTRL 0x0660
+#define ESS_PORT1_LOOKUP_CTRL 0x066C
+#define ESS_PORT2_LOOKUP_CTRL 0x0678
+#define ESS_PORT3_LOOKUP_CTRL 0x0684
+#define ESS_PORT4_LOOKUP_CTRL 0x0690
+#define ESS_PORT5_LOOKUP_CTRL 0x069C
+
+#define ESS_PORT0_HEADER_CTRL 0x009C
+
+#define ESS_PORTS_ALL 0x3f
+
+#define ESS_FWD_CTRL1 0x0624
+#define ESS_FWD_CTRL1_UC_FLOOD BITS(0, 7)
+#define ESS_FWD_CTRL1_UC_FLOOD_S 0
+#define ESS_FWD_CTRL1_MC_FLOOD BITS(8, 7)
+#define ESS_FWD_CTRL1_MC_FLOOD_S 8
+#define ESS_FWD_CTRL1_BC_FLOOD BITS(16, 7)
+#define ESS_FWD_CTRL1_BC_FLOOD_S 16
+#define ESS_FWD_CTRL1_IGMP BITS(24, 7)
+#define ESS_FWD_CTRL1_IGMP_S 24
+
+#endif /* _ESS_EDMA_H_ */
--- /dev/null
+From 61a3bd10082b0e861b4e1bc451a92e20181a52f5 Mon Sep 17 00:00:00 2001
+From: Felix Fietkau <nbd@nbd.name>
+Date: Mon, 23 Jul 2018 16:17:35 +0200
+Subject: [PATCH] soc: qcom: spm: add SCM probe dependency
+
+Check for SCM availability before attempting to use SPM. SPM probe will
+fail otherwise.
+
+Signed-off-by: Felix Fietkau <nbd@nbd.name>
+Signed-off-by: John Crispin <john@phrozen.org>
+Signed-off-by: Andy Gross <andy.gross@linaro.org>
+---
+ drivers/soc/qcom/spm.c | 3 +++
+ 1 file changed, 3 insertions(+)
+
+--- a/drivers/soc/qcom/spm.c
++++ b/drivers/soc/qcom/spm.c
+@@ -219,6 +219,9 @@ static int __init qcom_cpuidle_init(stru
+ cpumask_t mask;
+ bool use_scm_power_down = false;
+
++ if (!qcom_scm_is_available())
++ return -EPROBE_DEFER;
++
+ for (i = 0; ; i++) {
+ state_node = of_parse_phandle(cpu_node, "cpu-idle-states", i);
+ if (!state_node)
--- /dev/null
+From 8a4540321e8bcf7a5b485c332a2e78f3501c78ed Mon Sep 17 00:00:00 2001
+From: Robert Marko <robimarko@gmail.com>
+Date: Thu, 29 Nov 2018 22:29:36 +0100
+Subject: [PATCH] ipq40xx: Fix booting secondary cores
+
+Add the second part of old 071-qcom-ipq4019-use-v2-of-the-kpss-bringup-mechanism.patch
+We dont modify the patch itself as its upstream and this change is not.
+
+Originally added by Mantas Pucka Mantas Pucka <mantas@8devices.com>
+
+Signed-off-by: Robert Marko <robimarko@gmail.com>
+---
+ arch/arm/boot/dts/qcom-ipq4019.dtsi | 7 +++++++
+ 1 file changed, 7 insertions(+)
+
+--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
+@@ -132,6 +132,7 @@
+ L2: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
++ qcom,saw = <&saw_l2>;
+ };
+ };
+
+@@ -344,6 +345,12 @@
+ regulator;
+ };
+
++ saw_l2: regulator@b012000 {
++ compatible = "qcom,saw2";
++ reg = <0xb012000 0x1000>;
++ regulator;
++ };
++
+ blsp1_uart1: serial@78af000 {
+ compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+ reg = <0x78af000 0x200>;
--- /dev/null
+From 89b43d59ec8c9cda588555eb1f2754dd19ef5144 Mon Sep 17 00:00:00 2001
+From: Christian Lamparter <chunkeey@gmail.com>
+Date: Sun, 22 Jul 2018 12:07:57 +0200
+Subject: [PATCH 8/8] ARM: qcom: Add IPQ4019 SoC support
+
+Add support for the Qualcomm Atheros IPQ4019 SoC.
+
+Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ arch/arm/Makefile | 1 +
+ arch/arm/mach-qcom/Kconfig | 5 +++++
+ 2 files changed, 6 insertions(+)
+
+--- a/arch/arm/Makefile
++++ b/arch/arm/Makefile
+@@ -150,6 +150,7 @@ textofs-$(CONFIG_ARCH_MSM8X60) := 0x0020
+ textofs-$(CONFIG_ARCH_MSM8960) := 0x00208000
+ textofs-$(CONFIG_ARCH_MESON) := 0x00208000
+ textofs-$(CONFIG_ARCH_AXXIA) := 0x00308000
++textofs-$(CONFIG_ARCH_IPQ40XX) := 0x00208000
+
+ # Machine directory name. This list is sorted alphanumerically
+ # by CONFIG_* macro name.
+--- a/arch/arm/mach-qcom/Kconfig
++++ b/arch/arm/mach-qcom/Kconfig
+@@ -27,4 +27,9 @@ config ARCH_MDM9615
+ bool "Enable support for MDM9615"
+ select CLKSRC_QCOM
+
++config ARCH_IPQ40XX
++ bool "Enable support for IPQ40XX"
++ select CLKSRC_QCOM
++ select HAVE_ARM_ARCH_TIMER
++
+ endif
--- /dev/null
+From 5f01733dc755dfadfa51b7b3c6c160e632fc6002 Mon Sep 17 00:00:00 2001
+From: John Crispin <john@phrozen.org>
+Date: Tue, 24 Jul 2018 15:09:36 +0200
+Subject: [PATCH 1/3] dt-bindings: phy-qcom-ipq4019-usb: add binding document
+
+This patch adds the binding documentation for the HS/SS USB PHY found
+inside Qualcom Dakota SoCs.
+
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ .../bindings/phy/phy-qcom-ipq4019-usb.txt | 21 +++++++++++++++++++++
+ 1 file changed, 21 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/phy/phy-qcom-ipq4019-usb.txt
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/phy/phy-qcom-ipq4019-usb.txt
+@@ -0,0 +1,21 @@
++Qualcom Dakota HS/SS USB PHY
++
++Required properties:
++ - compatible: "qcom,usb-ss-ipq4019-phy",
++ "qcom,usb-hs-ipq4019-phy"
++ - reg: offset and length of the registers
++ - #phy-cells: should be 0
++ - resets: the reset controllers as listed below
++ - reset-names: the names of the reset controllers
++ "por_rst" - the POR reset line for SS and HS phys
++ "srif_rst" - the SRIF reset line for HS phys
++Example:
++
++hsphy@a8000 {
++ compatible = "qcom,usb-hs-ipq4019-phy";
++ phy-cells = <0>;
++ reg = <0xa8000 0x40>;
++ resets = <&gcc USB2_HSPHY_POR_ARES>,
++ <&gcc USB2_HSPHY_S_ARES>;
++ reset-names = "por_rst", "srif_rst";
++};
--- /dev/null
+From 633f0e08498aebfdb932bd71319b4cb136709499 Mon Sep 17 00:00:00 2001
+From: John Crispin <john@phrozen.org>
+Date: Tue, 24 Jul 2018 14:45:49 +0200
+Subject: [PATCH 2/3] phy: qcom-ipq4019-usb: add driver for QCOM/IPQ4019
+
+Add a driver to setup the USB phy on Qualcom Dakota SoCs.
+The driver sets up HS and SS phys. In case of HS some magic values need to
+be written to magic offsets. These were taken from the SDK driver.
+
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ drivers/phy/qualcomm/Kconfig | 7 ++
+ drivers/phy/qualcomm/Makefile | 1 +
+ drivers/phy/qualcomm/phy-qcom-ipq4019-usb.c | 188 ++++++++++++++++++++++++++++
+ 3 files changed, 196 insertions(+)
+ create mode 100644 drivers/phy/qualcomm/phy-qcom-ipq4019-usb.c
+
+--- a/drivers/phy/qualcomm/Kconfig
++++ b/drivers/phy/qualcomm/Kconfig
+@@ -17,6 +17,13 @@ config PHY_QCOM_APQ8064_SATA
+ depends on OF
+ select GENERIC_PHY
+
++config PHY_QCOM_IPQ4019_USB
++ tristate "Qualcomm IPQ4019 USB PHY module"
++ depends on OF && ARCH_QCOM
++ select GENERIC_PHY
++ help
++ Support for the USB PHY on QCOM IPQ4019/Dakota chipsets.
++
+ config PHY_QCOM_IPQ806X_SATA
+ tristate "Qualcomm IPQ806x SATA SerDes/PHY driver"
+ depends on ARCH_QCOM
+--- /dev/null
++++ b/drivers/phy/qualcomm/phy-qcom-ipq4019-usb.c
+@@ -0,0 +1,188 @@
++/*
++ * Copyright (C) 2018 John Crispin <john@phrozen.org>
++ *
++ * Based on code from
++ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/delay.h>
++#include <linux/err.h>
++#include <linux/io.h>
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/mutex.h>
++#include <linux/of_platform.h>
++#include <linux/phy/phy.h>
++#include <linux/platform_device.h>
++#include <linux/reset.h>
++
++/*
++ * Magic registers copied from the SDK driver code
++ */
++#define PHY_CTRL0_ADDR 0x000
++#define PHY_CTRL1_ADDR 0x004
++#define PHY_CTRL2_ADDR 0x008
++#define PHY_CTRL3_ADDR 0x00C
++#define PHY_CTRL4_ADDR 0x010
++#define PHY_MISC_ADDR 0x024
++#define PHY_IPG_ADDR 0x030
++
++#define PHY_CTRL0_VAL 0xA4600015
++#define PHY_CTRL1_VAL 0x09500000
++#define PHY_CTRL2_VAL 0x00058180
++#define PHY_CTRL3_VAL 0x6DB6DCD6
++#define PHY_CTRL4_VAL 0x836DB6DB
++#define PHY_MISC_VAL 0x3803FB0C
++#define PHY_IPG_VAL 0x47323232
++
++struct ipq4019_usb_phy {
++ struct device *dev;
++ struct phy *phy;
++ void __iomem *base;
++ struct reset_control *por_rst;
++ struct reset_control *srif_rst;
++};
++
++static int ipq4019_ss_phy_power_off(struct phy *_phy)
++{
++ struct ipq4019_usb_phy *phy = phy_get_drvdata(_phy);
++
++ reset_control_assert(phy->por_rst);
++ msleep(10);
++
++ return 0;
++}
++
++static int ipq4019_ss_phy_power_on(struct phy *_phy)
++{
++ struct ipq4019_usb_phy *phy = phy_get_drvdata(_phy);
++
++ ipq4019_ss_phy_power_off(_phy);
++
++ reset_control_deassert(phy->por_rst);
++
++ return 0;
++}
++
++static struct phy_ops ipq4019_usb_ss_phy_ops = {
++ .power_on = ipq4019_ss_phy_power_on,
++ .power_off = ipq4019_ss_phy_power_off,
++};
++
++static int ipq4019_hs_phy_power_off(struct phy *_phy)
++{
++ struct ipq4019_usb_phy *phy = phy_get_drvdata(_phy);
++
++ reset_control_assert(phy->por_rst);
++ msleep(10);
++
++ reset_control_assert(phy->srif_rst);
++ msleep(10);
++
++ return 0;
++}
++
++static int ipq4019_hs_phy_power_on(struct phy *_phy)
++{
++ struct ipq4019_usb_phy *phy = phy_get_drvdata(_phy);
++
++ ipq4019_hs_phy_power_off(_phy);
++
++ reset_control_deassert(phy->srif_rst);
++ msleep(10);
++
++ writel(PHY_CTRL0_VAL, phy->base + PHY_CTRL0_ADDR);
++ writel(PHY_CTRL1_VAL, phy->base + PHY_CTRL1_ADDR);
++ writel(PHY_CTRL2_VAL, phy->base + PHY_CTRL2_ADDR);
++ writel(PHY_CTRL3_VAL, phy->base + PHY_CTRL3_ADDR);
++ writel(PHY_CTRL4_VAL, phy->base + PHY_CTRL4_ADDR);
++ writel(PHY_MISC_VAL, phy->base + PHY_MISC_ADDR);
++ writel(PHY_IPG_VAL, phy->base + PHY_IPG_ADDR);
++ msleep(10);
++
++ reset_control_deassert(phy->por_rst);
++
++ return 0;
++}
++
++static struct phy_ops ipq4019_usb_hs_phy_ops = {
++ .power_on = ipq4019_hs_phy_power_on,
++ .power_off = ipq4019_hs_phy_power_off,
++};
++
++static const struct of_device_id ipq4019_usb_phy_of_match[] = {
++ { .compatible = "qcom,usb-hs-ipq4019-phy", .data = &ipq4019_usb_hs_phy_ops},
++ { .compatible = "qcom,usb-ss-ipq4019-phy", .data = &ipq4019_usb_ss_phy_ops},
++ { },
++};
++MODULE_DEVICE_TABLE(of, ipq4019_usb_phy_of_match);
++
++static int ipq4019_usb_phy_probe(struct platform_device *pdev)
++{
++ struct device *dev = &pdev->dev;
++ struct resource *res;
++ struct phy_provider *phy_provider;
++ struct ipq4019_usb_phy *phy;
++ const struct of_device_id *match;
++
++ match = of_match_device(ipq4019_usb_phy_of_match, &pdev->dev);
++ if (!match)
++ return -ENODEV;
++
++ phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
++ if (!phy)
++ return -ENOMEM;
++
++ phy->dev = &pdev->dev;
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ phy->base = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(phy->base)) {
++ dev_err(dev, "failed to remap register memory\n");
++ return PTR_ERR(phy->base);
++ }
++
++ phy->por_rst = devm_reset_control_get(phy->dev, "por_rst");
++ if (IS_ERR(phy->por_rst)) {
++ if (PTR_ERR(phy->por_rst) != -EPROBE_DEFER)
++ dev_err(dev, "POR reset is missing\n");
++ return PTR_ERR(phy->por_rst);
++ }
++
++ phy->srif_rst = devm_reset_control_get_optional(phy->dev, "srif_rst");
++ if (IS_ERR(phy->srif_rst))
++ return PTR_ERR(phy->srif_rst);
++
++ phy->phy = devm_phy_create(dev, NULL, match->data);
++ if (IS_ERR(phy->phy)) {
++ dev_err(dev, "failed to create PHY\n");
++ return PTR_ERR(phy->phy);
++ }
++ phy_set_drvdata(phy->phy, phy);
++
++ phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
++
++ return PTR_ERR_OR_ZERO(phy_provider);
++}
++
++static struct platform_driver ipq4019_usb_phy_driver = {
++ .probe = ipq4019_usb_phy_probe,
++ .driver = {
++ .of_match_table = ipq4019_usb_phy_of_match,
++ .name = "ipq4019-usb-phy",
++ }
++};
++module_platform_driver(ipq4019_usb_phy_driver);
++
++MODULE_DESCRIPTION("QCOM/IPQ4019 USB phy driver");
++MODULE_AUTHOR("John Crispin <john@phrozen.org>");
++MODULE_LICENSE("GPL v2");
+--- a/drivers/phy/qualcomm/Makefile
++++ b/drivers/phy/qualcomm/Makefile
+@@ -1,6 +1,7 @@
+ # SPDX-License-Identifier: GPL-2.0
+ obj-$(CONFIG_PHY_ATH79_USB) += phy-ath79-usb.o
+ obj-$(CONFIG_PHY_QCOM_APQ8064_SATA) += phy-qcom-apq8064-sata.o
++obj-$(CONFIG_PHY_QCOM_IPQ4019_USB) += phy-qcom-ipq4019-usb.o
+ obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
+ obj-$(CONFIG_PHY_QCOM_QMP) += phy-qcom-qmp.o
+ obj-$(CONFIG_PHY_QCOM_QUSB2) += phy-qcom-qusb2.o
--- /dev/null
+From 1fc7d5523e21ed140fed43c4dde011a3b6d9ba08 Mon Sep 17 00:00:00 2001
+From: John Crispin <john@phrozen.org>
+Date: Tue, 24 Jul 2018 14:47:55 +0200
+Subject: [PATCH 3/3] qcom: ipq4019: add USB devicetree nodes
+
+This patch makes USB work on the Dakota EVB.
+
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi | 20 ++++++++
+ arch/arm/boot/dts/qcom-ipq4019.dtsi | 74 +++++++++++++++++++++++++++
+ 2 files changed, 94 insertions(+)
+
+--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
+@@ -109,5 +109,25 @@
+ wifi@a800000 {
+ status = "ok";
+ };
++
++ usb3_ss_phy: ssphy@9a000 {
++ status = "ok";
++ };
++
++ usb3_hs_phy: hsphy@a6000 {
++ status = "ok";
++ };
++
++ usb3: usb3@8af8800 {
++ status = "ok";
++ };
++
++ usb2_hs_phy: hsphy@a8000 {
++ status = "ok";
++ };
++
++ usb2: usb2@60f8800 {
++ status = "ok";
++ };
+ };
+ };
+--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
+@@ -568,5 +568,79 @@
+ "legacy";
+ status = "disabled";
+ };
++
++ usb3_ss_phy: ssphy@9a000 {
++ compatible = "qcom,usb-ss-ipq4019-phy";
++ #phy-cells = <0>;
++ reg = <0x9a000 0x800>;
++ reg-names = "phy_base";
++ resets = <&gcc USB3_UNIPHY_PHY_ARES>;
++ reset-names = "por_rst";
++ status = "disabled";
++ };
++
++ usb3_hs_phy: hsphy@a6000 {
++ compatible = "qcom,usb-hs-ipq4019-phy";
++ #phy-cells = <0>;
++ reg = <0xa6000 0x40>;
++ reg-names = "phy_base";
++ resets = <&gcc USB3_HSPHY_POR_ARES>, <&gcc USB3_HSPHY_S_ARES>;
++ reset-names = "por_rst", "srif_rst";
++ status = "disabled";
++ };
++
++ usb3@8af8800 {
++ compatible = "qcom,dwc3";
++ reg = <0x8af8800 0x100>;
++ #address-cells = <1>;
++ #size-cells = <1>;
++ clocks = <&gcc GCC_USB3_MASTER_CLK>,
++ <&gcc GCC_USB3_SLEEP_CLK>,
++ <&gcc GCC_USB3_MOCK_UTMI_CLK>;
++ clock-names = "master", "sleep", "mock_utmi";
++ ranges;
++ status = "disabled";
++
++ dwc3@8a00000 {
++ compatible = "snps,dwc3";
++ reg = <0x8a00000 0xf8000>;
++ interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
++ phys = <&usb3_hs_phy>, <&usb3_ss_phy>;
++ phy-names = "usb2-phy", "usb3-phy";
++ dr_mode = "host";
++ };
++ };
++
++ usb2_hs_phy: hsphy@a8000 {
++ compatible = "qcom,usb-hs-ipq4019-phy";
++ #phy-cells = <0>;
++ reg = <0xa8000 0x40>;
++ reg-names = "phy_base";
++ resets = <&gcc USB2_HSPHY_POR_ARES>, <&gcc USB2_HSPHY_S_ARES>;
++ reset-names = "por_rst", "srif_rst";
++ status = "disabled";
++ };
++
++ usb2@60f8800 {
++ compatible = "qcom,dwc3";
++ reg = <0x60f8800 0x100>;
++ #address-cells = <1>;
++ #size-cells = <1>;
++ clocks = <&gcc GCC_USB2_MASTER_CLK>,
++ <&gcc GCC_USB2_SLEEP_CLK>,
++ <&gcc GCC_USB2_MOCK_UTMI_CLK>;
++ clock-names = "master", "sleep", "mock_utmi";
++ ranges;
++ status = "disabled";
++
++ dwc3@6000000 {
++ compatible = "snps,dwc3";
++ reg = <0x6000000 0xf8000>;
++ interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
++ phys = <&usb2_hs_phy>;
++ phy-names = "usb2-phy";
++ dr_mode = "host";
++ };
++ };
+ };
+ };
--- /dev/null
+From patchwork Mon May 21 20:57:38 2018
+Content-Type: text/plain; charset="utf-8"
+MIME-Version: 1.0
+Content-Transfer-Encoding: 7bit
+Subject: [v5,3/4] ARM: dts: qcom: add gpio-ranges property
+X-Patchwork-Submitter: Christian Lamparter <chunkeey@gmail.com>
+X-Patchwork-Id: 917856
+Message-Id: <0ae3376606a89bcdf3fe753a5c967f7103699e09.1526935804.git.chunkeey@gmail.com>
+To: linux-gpio@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
+ linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org
+Cc: Bjorn Andersson <bjorn.andersson@linaro.org>,
+ Linus Walleij <linus.walleij@linaro.org>,
+ Stephen Boyd <sboyd@kernel.org>, David Brown <david.brown@linaro.org>,
+ Rob Herring <robh+dt@kernel.org>, Mark Rutland <mark.rutland@arm.com>,
+ Andy Gross <andy.gross@linaro.org>,
+ Sven Eckelmann <sven.eckelmann@openmesh.com>
+Date: Mon, 21 May 2018 22:57:38 +0200
+From: Christian Lamparter <chunkeey@gmail.com>
+List-Id: <linux-gpio.vger.kernel.org>
+
+This patch adds the gpio-ranges property to almost all of
+the Qualcomm ARM platforms that utilize the pinctrl-msm
+framework.
+
+The gpio-ranges property is part of the gpiolib subsystem.
+As a result, the binding text is available in section
+"2.1 gpio- and pin-controller interaction" of
+Documentation/devicetree/bindings/gpio/gpio.txt
+
+For more information please see the patch titled:
+"pinctrl: msm: fix gpio-hog related boot issues" from
+this series.
+
+Reported-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
+Tested-by: Sven Eckelmann <sven.eckelmann@openmesh.com> [ipq4019]
+Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
+Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
+Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
+---
+To help with git bisect, the DT update patch has been intentionally
+placed after the "pinctrl: msm: fix gpio-hog related boot issues".
+Otherwise - if the order was reveresed - and bisect decides to split
+between these two patches, the gpiochip_add_pin_ranges() function
+will be executed twice with the same parameters for the same pinctrl.
+---
+ arch/arm/boot/dts/qcom-apq8064.dtsi | 1 +
+ arch/arm/boot/dts/qcom-apq8084.dtsi | 1 +
+ arch/arm/boot/dts/qcom-ipq4019.dtsi | 1 +
+ arch/arm/boot/dts/qcom-ipq8064.dtsi | 1 +
+ arch/arm/boot/dts/qcom-mdm9615.dtsi | 1 +
+ arch/arm/boot/dts/qcom-msm8660.dtsi | 1 +
+ arch/arm/boot/dts/qcom-msm8960.dtsi | 1 +
+ arch/arm/boot/dts/qcom-msm8974.dtsi | 1 +
+ arch/arm64/boot/dts/qcom/ipq8074.dtsi | 3 ++-
+ arch/arm64/boot/dts/qcom/msm8916.dtsi | 1 +
+ arch/arm64/boot/dts/qcom/msm8992.dtsi | 1 +
+ arch/arm64/boot/dts/qcom/msm8994.dtsi | 1 +
+ arch/arm64/boot/dts/qcom/msm8996.dtsi | 1 +
+ 13 files changed, 14 insertions(+), 1 deletion(-)
+
+--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
+@@ -206,6 +206,7 @@
+ compatible = "qcom,ipq4019-pinctrl";
+ reg = <0x01000000 0x300000>;
+ gpio-controller;
++ gpio-ranges = <&tlmm 0 0 100>;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
--- /dev/null
+From f2b87dc1028b710ec8ce25808b9d21f92b376184 Mon Sep 17 00:00:00 2001
+From: Christian Lamparter <chunkeey@googlemail.com>
+Date: Sun, 11 Mar 2018 14:41:31 +0100
+Subject: [PATCH 2/2] clk: fix apss cpu overclocking
+
+There's an interaction issue between the clk changes:"
+clk: qcom: ipq4019: Add the apss cpu pll divider clock node
+clk: qcom: ipq4019: remove fixed clocks and add pll clocks
+" and the cpufreq-dt.
+
+cpufreq-dt is now spamming the kernel-log with the following:
+
+[ 1099.190658] cpu cpu0: dev_pm_opp_set_rate: failed to find current OPP
+for freq 761142857 (-34)
+
+This only happens on certain devices like the Compex WPJ428
+and AVM FritzBox!4040. However, other devices like the Asus
+RT-AC58U and Meraki MR33 work just fine.
+
+The issue stem from the fact that all higher CPU-Clocks
+are achieved by switching the clock-parent to the P_DDRPLLAPSS
+(ddrpllapss). Which is set by Qualcomm's proprietary bootcode
+as part of the DDR calibration.
+
+For example, the FB4040 uses 256 MiB Nanya NT5CC128M16IP clocked
+at round 533 MHz (ddrpllsdcc = 190285714 Hz).
+
+whereas the 128 MiB Nanya NT5CC64M16GP-DI in the ASUS RT-AC58U is
+clocked at a slightly higher 537 MHz ( ddrpllsdcc = 192000000 Hz).
+
+This patch attempts to fix the issue by modifying
+clk_cpu_div_round_rate(), clk_cpu_div_set_rate(), clk_cpu_div_recalc_rate()
+to use a new qcom_find_freq_close() function, which returns the closest
+matching frequency, instead of the next higher. This way, the SoC in
+the FB4040 (with its max clock speed of 710.4 MHz) will no longer
+try to overclock to 761 MHz.
+
+Fixes: d83dcacea18 ("clk: qcom: ipq4019: Add the apss cpu pll divider clock node")
+Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ drivers/clk/qcom/gcc-ipq4019.c | 34 +++++++++++++++++++++++++++++++---
+ 1 file changed, 31 insertions(+), 3 deletions(-)
+
+--- a/drivers/clk/qcom/gcc-ipq4019.c
++++ b/drivers/clk/qcom/gcc-ipq4019.c
+@@ -1251,6 +1251,29 @@ static const struct clk_fepll_vco gcc_fe
+ .reg = 0x2f020,
+ };
+
++
++const struct freq_tbl *qcom_find_freq_close(const struct freq_tbl *f,
++ unsigned long rate)
++{
++ const struct freq_tbl *last = NULL;
++
++ for ( ; f->freq; f++) {
++ if (rate == f->freq)
++ return f;
++
++ if (f->freq > rate) {
++ if (!last ||
++ (f->freq - rate) < (rate - last->freq))
++ return f;
++ else
++ return last;
++ }
++ last = f;
++ }
++
++ return last;
++}
++
+ /*
+ * Round rate function for APSS CPU PLL Clock divider.
+ * It looks up the frequency table and returns the next higher frequency
+@@ -1263,7 +1286,7 @@ static long clk_cpu_div_round_rate(struc
+ struct clk_hw *p_hw;
+ const struct freq_tbl *f;
+
+- f = qcom_find_freq(pll->freq_tbl, rate);
++ f = qcom_find_freq_close(pll->freq_tbl, rate);
+ if (!f)
+ return -EINVAL;
+
+@@ -1286,7 +1309,7 @@ static int clk_cpu_div_set_rate(struct c
+ u32 mask;
+ int ret;
+
+- f = qcom_find_freq(pll->freq_tbl, rate);
++ f = qcom_find_freq_close(pll->freq_tbl, rate);
+ if (!f)
+ return -EINVAL;
+
+@@ -1313,6 +1336,7 @@ static unsigned long
+ clk_cpu_div_recalc_rate(struct clk_hw *hw,
+ unsigned long parent_rate)
+ {
++ const struct freq_tbl *f;
+ struct clk_fepll *pll = to_clk_fepll(hw);
+ u32 cdiv, pre_div;
+ u64 rate;
+@@ -1333,7 +1357,11 @@ clk_cpu_div_recalc_rate(struct clk_hw *h
+ rate = clk_fepll_vco_calc_rate(pll, parent_rate) * 2;
+ do_div(rate, pre_div);
+
+- return rate;
++ f = qcom_find_freq_close(pll->freq_tbl, rate);
++ if (!f)
++ return rate;
++
++ return f->freq;
+ };
+
+ static const struct clk_ops clk_regmap_cpu_div_ops = {
--- /dev/null
+From 09f145f417a5d64d6b8d4476699dfb0eccc6c784 Mon Sep 17 00:00:00 2001
+From: Abhishek Sahu <absahu@codeaurora.org>
+Date: Tue, 7 May 2019 10:14:05 +0300
+Subject: [PATCH] ipq40xx: fix high resolution timer
+
+Cherry-picked from CAF QSDK repo.
+Original commit message:
+The kernel is failing in switching the timer for high resolution
+mode and clock source operates in 10ms resolution. The always-on
+property needs to be given for timer device tree node to make
+clock source working in 1ns resolution.
+
+Change-Id: I7c00b3c74d97c2a30ac9f05e18b511a0550fd459
+Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
+Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
+---
+ arch/arm/boot/dts/qcom-ipq4019.dtsi | 1 +
+ 1 file changed, 1 insertion(+)
+
+--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
+@@ -171,6 +171,7 @@
+ <1 4 0xf08>,
+ <1 1 0xf08>;
+ clock-frequency = <48000000>;
++ always-on;
+ };
+
+ soc {
--- /dev/null
+From: Eneas U de Queiroz <cotequeiroz@gmail.com>
+Subject: [PATCH] crypto: qce - add CRYPTO_ALG_KERN_DRIVER_ONLY flag
+
+Set the CRYPTO_ALG_KERN_DRIVER_ONLY flag to all algorithms exposed by
+the qce driver, since they are all hardware accelerated, accessible
+through a kernel driver only, and not available directly to userspace.
+
+Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
+
+--- a/drivers/crypto/qce/ablkcipher.c
++++ b/drivers/crypto/qce/ablkcipher.c
+@@ -370,7 +370,7 @@ static int qce_ablkcipher_register_one(c
+
+ alg->cra_priority = 300;
+ alg->cra_flags = CRYPTO_ALG_TYPE_ABLKCIPHER | CRYPTO_ALG_ASYNC |
+- CRYPTO_ALG_NEED_FALLBACK;
++ CRYPTO_ALG_NEED_FALLBACK | CRYPTO_ALG_KERN_DRIVER_ONLY;
+ alg->cra_ctxsize = sizeof(struct qce_cipher_ctx);
+ alg->cra_alignmask = 0;
+ alg->cra_type = &crypto_ablkcipher_type;
+--- a/drivers/crypto/qce/sha.c
++++ b/drivers/crypto/qce/sha.c
+@@ -503,7 +503,7 @@ static int qce_ahash_register_one(const
+ base = &alg->halg.base;
+ base->cra_blocksize = def->blocksize;
+ base->cra_priority = 300;
+- base->cra_flags = CRYPTO_ALG_ASYNC;
++ base->cra_flags = CRYPTO_ALG_ASYNC | CRYPTO_ALG_KERN_DRIVER_ONLY;
+ base->cra_ctxsize = sizeof(struct qce_sha_ctx);
+ base->cra_alignmask = 0;
+ base->cra_module = THIS_MODULE;
--- /dev/null
+From 480c1f7648fc586db12d6003c717c23667a4fcf0 Mon Sep 17 00:00:00 2001
+From: Ram Chandra Jangir <rjangir@codeaurora.org>
+Date: Tue, 28 Mar 2017 22:35:33 +0530
+Subject: [PATCH] clk: qcom: ipq4019: add ess reset
+
+Added the ESS reset in IPQ4019 GCC.
+
+Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
+---
+ drivers/clk/qcom/gcc-ipq4019.c | 11 +++++++++++
+ include/dt-bindings/clock/qcom,gcc-ipq4019.h | 11 +++++++++++
+ 2 files changed, 22 insertions(+)
+
+diff --git a/drivers/clk/qcom/gcc-ipq4019.c b/drivers/clk/qcom/gcc-ipq4019.c
+index b2dc68efd5c8..a8672c5870a5 100644
+--- a/drivers/clk/qcom/gcc-ipq4019.c
++++ b/drivers/clk/qcom/gcc-ipq4019.c
+@@ -1744,6 +1744,17 @@ static const struct qcom_reset_map gcc_ipq4019_resets[] = {
+ [GCC_TCSR_BCR] = {0x22000, 0},
+ [GCC_MPM_BCR] = {0x24000, 0},
+ [GCC_SPDM_BCR] = {0x25000, 0},
++ [ESS_MAC1_ARES] = {0x1200C, 0},
++ [ESS_MAC2_ARES] = {0x1200C, 1},
++ [ESS_MAC3_ARES] = {0x1200C, 2},
++ [ESS_MAC4_ARES] = {0x1200C, 3},
++ [ESS_MAC5_ARES] = {0x1200C, 4},
++ [ESS_PSGMII_ARES] = {0x1200C, 5},
++ [ESS_MAC1_CLK_DIS] = {0x1200C, 8},
++ [ESS_MAC2_CLK_DIS] = {0x1200C, 9},
++ [ESS_MAC3_CLK_DIS] = {0x1200C, 10},
++ [ESS_MAC4_CLK_DIS] = {0x1200C, 11},
++ [ESS_MAC5_CLK_DIS] = {0x1200C, 12},
+ };
+
+ static const struct regmap_config gcc_ipq4019_regmap_config = {
+diff --git a/include/dt-bindings/clock/qcom,gcc-ipq4019.h b/include/dt-bindings/clock/qcom,gcc-ipq4019.h
+index 7e8a7be6dcda..b8f0cdcd9ec0 100644
+--- a/include/dt-bindings/clock/qcom,gcc-ipq4019.h
++++ b/include/dt-bindings/clock/qcom,gcc-ipq4019.h
+@@ -165,5 +165,16 @@
+ #define GCC_QDSS_BCR 69
+ #define GCC_MPM_BCR 70
+ #define GCC_SPDM_BCR 71
++#define ESS_MAC1_ARES 72
++#define ESS_MAC2_ARES 73
++#define ESS_MAC3_ARES 74
++#define ESS_MAC4_ARES 75
++#define ESS_MAC5_ARES 76
++#define ESS_PSGMII_ARES 77
++#define ESS_MAC1_CLK_DIS 78
++#define ESS_MAC2_CLK_DIS 79
++#define ESS_MAC3_CLK_DIS 80
++#define ESS_MAC4_CLK_DIS 81
++#define ESS_MAC5_CLK_DIS 82
+
+ #endif
+--
+2.20.1
+
--- /dev/null
+From 158acdbf0336f601971637f988b57a6a67a0869b Mon Sep 17 00:00:00 2001
+From: David Bauer <mail@david-bauer.net>
+Date: Sun, 15 Dec 2019 13:10:50 +0100
+Subject: [PATCH] mtd: spi-nor: Add support for mx25r3235f
+
+Add MTD support for the Macronix MX25R3235F SPI NOR chip from Macronix.
+The chip has 4MB of total capacity, divided into a total of 64 sectors,
+each 64KB sized. The chip also supports 4KB large sectors.
+Additionally, it supports dual and quad read modes.
+
+Signed-off-by: David Bauer <mail@david-bauer.net>
+---
+ drivers/mtd/spi-nor/spi-nor.c | 2 ++
+ 1 file changed, 2 insertions(+)
+
+--- a/drivers/mtd/spi-nor/spi-nor.c
++++ b/drivers/mtd/spi-nor/spi-nor.c
+@@ -1091,6 +1091,8 @@ static const struct flash_info spi_nor_i
+ { "mx25u6435f", INFO(0xc22537, 0, 64 * 1024, 128, SECT_4K) },
+ { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
+ { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
++ { "mx25r3235f", INFO(0xc22816, 0, 64 * 1024, 64,
++ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "mx25u12835f", INFO(0xc22538, 0, 64 * 1024, 256,
+ SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
+ { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
--- /dev/null
+--- a/drivers/net/phy/Kconfig
++++ b/drivers/net/phy/Kconfig
+@@ -519,6 +519,13 @@ config XILINX_GMII2RGMII
+ the Reduced Gigabit Media Independent Interface(RGMII) between
+ Ethernet physical media devices and the Gigabit Ethernet controller.
+
++config MDIO_IPQ40XX
++ tristate "Qualcomm Atheros ipq40xx MDIO interface"
++ depends on HAS_IOMEM && OF
++ ---help---
++ This driver supports the MDIO interface found in Qualcomm
++ Atheros ipq40xx Soc chip.
++
+ endif # PHYLIB
+
+ config MICREL_KS8995MA
+--- a/drivers/net/phy/Makefile
++++ b/drivers/net/phy/Makefile
+@@ -48,6 +48,7 @@ obj-$(CONFIG_MDIO_CAVIUM) += mdio-cavium
+ obj-$(CONFIG_MDIO_GPIO) += mdio-gpio.o
+ obj-$(CONFIG_MDIO_HISI_FEMAC) += mdio-hisi-femac.o
+ obj-$(CONFIG_MDIO_I2C) += mdio-i2c.o
++obj-$(CONFIG_MDIO_IPQ40XX) += mdio-ipq40xx.o
+ obj-$(CONFIG_MDIO_MOXART) += mdio-moxart.o
+ obj-$(CONFIG_MDIO_MSCC_MIIM) += mdio-mscc-miim.o
+ obj-$(CONFIG_MDIO_OCTEON) += mdio-octeon.o
+--- /dev/null
++++ b/drivers/net/phy/mdio-ipq40xx.c
+@@ -0,0 +1,196 @@
++/*
++ * Copyright (c) 2015-2016, The Linux Foundation. All rights reserved.
++ *
++ * Permission to use, copy, modify, and/or distribute this software for
++ * any purpose with or without fee is hereby granted, provided that the
++ * above copyright notice and this permission notice appear in all copies.
++ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
++ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
++ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
++ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
++ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
++ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT
++ * OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
++ */
++
++#include <linux/delay.h>
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/mutex.h>
++#include <linux/io.h>
++#include <linux/of_address.h>
++#include <linux/of_mdio.h>
++#include <linux/phy.h>
++#include <linux/platform_device.h>
++
++#define MDIO_CTRL_0_REG 0x40
++#define MDIO_CTRL_1_REG 0x44
++#define MDIO_CTRL_2_REG 0x48
++#define MDIO_CTRL_3_REG 0x4c
++#define MDIO_CTRL_4_REG 0x50
++#define MDIO_CTRL_4_ACCESS_BUSY BIT(16)
++#define MDIO_CTRL_4_ACCESS_START BIT(8)
++#define MDIO_CTRL_4_ACCESS_CODE_READ 0
++#define MDIO_CTRL_4_ACCESS_CODE_WRITE 1
++#define CTRL_0_REG_DEFAULT_VALUE 0x150FF
++
++#define IPQ40XX_MDIO_RETRY 1000
++#define IPQ40XX_MDIO_DELAY 10
++
++struct ipq40xx_mdio_data {
++ struct mii_bus *mii_bus;
++ void __iomem *membase;
++ struct device *dev;
++};
++
++static int ipq40xx_mdio_wait_busy(struct ipq40xx_mdio_data *am)
++{
++ int i;
++
++ for (i = 0; i < IPQ40XX_MDIO_RETRY; i++) {
++ unsigned int busy;
++
++ busy = readl(am->membase + MDIO_CTRL_4_REG) &
++ MDIO_CTRL_4_ACCESS_BUSY;
++ if (!busy)
++ return 0;
++
++ /* BUSY might take to be cleard by 15~20 times of loop */
++ udelay(IPQ40XX_MDIO_DELAY);
++ }
++
++ dev_err(am->dev, "%s: MDIO operation timed out\n", am->mii_bus->name);
++
++ return -ETIMEDOUT;
++}
++
++static int ipq40xx_mdio_read(struct mii_bus *bus, int mii_id, int regnum)
++{
++ struct ipq40xx_mdio_data *am = bus->priv;
++ int value = 0;
++ unsigned int cmd = 0;
++
++ lockdep_assert_held(&bus->mdio_lock);
++
++ if (ipq40xx_mdio_wait_busy(am))
++ return -ETIMEDOUT;
++
++ /* issue the phy address and reg */
++ writel((mii_id << 8) | regnum, am->membase + MDIO_CTRL_1_REG);
++
++ cmd = MDIO_CTRL_4_ACCESS_START|MDIO_CTRL_4_ACCESS_CODE_READ;
++
++ /* issue read command */
++ writel(cmd, am->membase + MDIO_CTRL_4_REG);
++
++ /* Wait read complete */
++ if (ipq40xx_mdio_wait_busy(am))
++ return -ETIMEDOUT;
++
++ /* Read data */
++ value = readl(am->membase + MDIO_CTRL_3_REG);
++
++ return value;
++}
++
++static int ipq40xx_mdio_write(struct mii_bus *bus, int mii_id, int regnum,
++ u16 value)
++{
++ struct ipq40xx_mdio_data *am = bus->priv;
++ unsigned int cmd = 0;
++
++ lockdep_assert_held(&bus->mdio_lock);
++
++ if (ipq40xx_mdio_wait_busy(am))
++ return -ETIMEDOUT;
++
++ /* issue the phy address and reg */
++ writel((mii_id << 8) | regnum, am->membase + MDIO_CTRL_1_REG);
++
++ /* issue write data */
++ writel(value, am->membase + MDIO_CTRL_2_REG);
++
++ cmd = MDIO_CTRL_4_ACCESS_START|MDIO_CTRL_4_ACCESS_CODE_WRITE;
++ /* issue write command */
++ writel(cmd, am->membase + MDIO_CTRL_4_REG);
++
++ /* Wait write complete */
++ if (ipq40xx_mdio_wait_busy(am))
++ return -ETIMEDOUT;
++
++ return 0;
++}
++
++static int ipq40xx_mdio_probe(struct platform_device *pdev)
++{
++ struct ipq40xx_mdio_data *am;
++ struct resource *res;
++ int i;
++
++ am = devm_kzalloc(&pdev->dev, sizeof(*am), GFP_KERNEL);
++ if (!am)
++ return -ENOMEM;
++
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ if (!res) {
++ dev_err(&pdev->dev, "no iomem resource found\n");
++ return -ENXIO;
++ }
++
++ am->membase = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(am->membase)) {
++ dev_err(&pdev->dev, "unable to ioremap registers\n");
++ return PTR_ERR(am->membase);
++ }
++
++ am->mii_bus = devm_mdiobus_alloc(&pdev->dev);
++ if (!am->mii_bus)
++ return -ENOMEM;
++
++ writel(CTRL_0_REG_DEFAULT_VALUE, am->membase + MDIO_CTRL_0_REG);
++
++ am->mii_bus->name = "ipq40xx_mdio";
++ am->mii_bus->read = ipq40xx_mdio_read;
++ am->mii_bus->write = ipq40xx_mdio_write;
++ am->mii_bus->priv = am;
++ am->mii_bus->parent = &pdev->dev;
++ snprintf(am->mii_bus->id, MII_BUS_ID_SIZE, "%s", dev_name(&pdev->dev));
++
++ am->dev = &pdev->dev;
++ platform_set_drvdata(pdev, am);
++
++ return of_mdiobus_register(am->mii_bus, pdev->dev.of_node);
++}
++
++static int ipq40xx_mdio_remove(struct platform_device *pdev)
++{
++ struct ipq40xx_mdio_data *am = platform_get_drvdata(pdev);
++
++ mdiobus_unregister(am->mii_bus);
++
++ return 0;
++}
++
++static const struct of_device_id ipq40xx_mdio_dt_ids[] = {
++ { .compatible = "qcom,ipq4019-mdio" },
++ { }
++};
++MODULE_DEVICE_TABLE(of, ipq40xx_mdio_dt_ids);
++
++static struct platform_driver ipq40xx_mdio_driver = {
++ .probe = ipq40xx_mdio_probe,
++ .remove = ipq40xx_mdio_remove,
++ .driver = {
++ .name = "ipq40xx-mdio",
++ .of_match_table = ipq40xx_mdio_dt_ids,
++ },
++};
++
++module_platform_driver(ipq40xx_mdio_driver);
++
++#define DRV_VERSION "1.0"
++
++MODULE_DESCRIPTION("IPQ40XX MDIO interface driver");
++MODULE_AUTHOR("Qualcomm Atheros");
++MODULE_VERSION(DRV_VERSION);
++MODULE_LICENSE("Dual BSD/GPL");
--- /dev/null
+From 09ed737593f71bcca08a537a6c15264a1a6add08 Mon Sep 17 00:00:00 2001
+From: Christian Lamparter <chunkeey@gmail.com>
+Date: Sun, 20 Nov 2016 01:10:33 +0100
+Subject: [PATCH] dts: ipq4019: add mdio node for ethernet
+
+This patch adds the mdio device-tree node.
+This is where the switch is connected to, so it's needed
+for the ethernet interfaces.
+
+Note: The driver isn't anywhere close to be upstream,
+so the info might change.
+---
+ arch/arm/boot/dts/qcom-ipq4019.dtsi | 28 ++++++++++++++++++++++++++++
+ 1 file changed, 28 insertions(+)
+
+--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
+@@ -571,6 +571,34 @@
+ status = "disabled";
+ };
+
++ mdio: mdio@90000 {
++ #address-cells = <1>;
++ #size-cells = <0>;
++ compatible = "qcom,ipq4019-mdio";
++ reg = <0x90000 0x64>;
++ status = "disabled";
++
++ ethphy0: ethernet-phy@0 {
++ reg = <0>;
++ };
++
++ ethphy1: ethernet-phy@1 {
++ reg = <1>;
++ };
++
++ ethphy2: ethernet-phy@2 {
++ reg = <2>;
++ };
++
++ ethphy3: ethernet-phy@3 {
++ reg = <3>;
++ };
++
++ ethphy4: ethernet-phy@4 {
++ reg = <4>;
++ };
++ };
++
+ usb3_ss_phy: ssphy@9a000 {
+ compatible = "qcom,usb-ss-ipq4019-phy";
+ #phy-cells = <0>;
--- /dev/null
+From 9deeec35dd3b628b95624e41d4e04acf728991ba Mon Sep 17 00:00:00 2001
+From: Christian Lamparter <chunkeey@gmail.com>
+Date: Sun, 20 Nov 2016 02:20:54 +0100
+Subject: [PATCH] dts: ipq4019: add PHY/switch nodes
+
+This patch adds both the "qcom,ess-switch" and "qcom,ess-psgmii"
+nodes which are needed for the ar40xx.c driver to initialize the
+switch.
+
+Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
+---
+ arch/arm/boot/dts/qcom-ipq4019.dtsi | 23 +++++++++++++++++++++++
+ 1 file changed, 23 insertions(+)
+
+--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
+@@ -599,6 +599,29 @@
+ };
+ };
+
++ ess-switch@c000000 {
++ compatible = "qcom,ess-switch";
++ reg = <0xc000000 0x80000>;
++ switch_access_mode = "local bus";
++ resets = <&gcc ESS_RESET>;
++ reset-names = "ess_rst";
++ clocks = <&gcc GCC_ESS_CLK>;
++ clock-names = "ess_clk";
++ switch_cpu_bmp = <0x1>;
++ switch_lan_bmp = <0x1e>;
++ switch_wan_bmp = <0x20>;
++ switch_mac_mode = <0>; /* PORT_WRAPPER_PSGMII */
++ switch_initvlas = <0x7c 0x54>;
++ status = "disabled";
++ };
++
++ ess-psgmii@98000 {
++ compatible = "qcom,ess-psgmii";
++ reg = <0x98000 0x800>;
++ psgmii_access_mode = "local bus";
++ status = "disabled";
++ };
++
+ usb3_ss_phy: ssphy@9a000 {
+ compatible = "qcom,usb-ss-ipq4019-phy";
+ #phy-cells = <0>;
--- /dev/null
+From 7c129254adb1093d10a62ed7bf7b956fcc6ffe34 Mon Sep 17 00:00:00 2001
+From: Rakesh Nair <ranair@codeaurora.org>
+Date: Wed, 20 Jul 2016 15:02:01 +0530
+Subject: [PATCH] net: IPQ4019 needs rfs/vlan_tag callbacks in
+ netdev_ops
+
+Add callback support to get default vlan tag and register
+receive flow steering filter.
+
+Used by IPQ4019 ess-edma driver.
+
+BUG=chrome-os-partner:33096
+TEST=none
+
+Change-Id: I266070e4a0fbe4a0d9966fe79a71e50ec4f26c75
+Signed-off-by: Rakesh Nair <ranair@codeaurora.org>
+Reviewed-on: https://chromium-review.googlesource.com/362203
+Commit-Ready: Grant Grundler <grundler@chromium.org>
+Tested-by: Grant Grundler <grundler@chromium.org>
+Reviewed-by: Grant Grundler <grundler@chromium.org>
+---
+ include/linux/netdevice.h | 13 +++++++++++++
+ 1 file changed, 13 insertions(+)
+
+--- a/include/linux/netdevice.h
++++ b/include/linux/netdevice.h
+@@ -739,6 +739,16 @@ struct xps_map {
+ #define XPS_MIN_MAP_ALLOC ((L1_CACHE_ALIGN(offsetof(struct xps_map, queues[1])) \
+ - sizeof(struct xps_map)) / sizeof(u16))
+
++#ifdef CONFIG_RFS_ACCEL
++typedef int (*set_rfs_filter_callback_t)(struct net_device *dev,
++ __be32 src,
++ __be32 dst,
++ __be16 sport,
++ __be16 dport,
++ u8 proto,
++ u16 rxq_index,
++ u32 action);
++#endif
+ /*
+ * This structure holds all XPS maps for device. Maps are indexed by CPU.
+ */
+@@ -1353,6 +1363,9 @@ struct net_device_ops {
+ const struct sk_buff *skb,
+ u16 rxq_index,
+ u32 flow_id);
++ int (*ndo_register_rfs_filter)(struct net_device *dev,
++ set_rfs_filter_callback_t set_filter);
++ int (*ndo_get_default_vlan_tag)(struct net_device *net);
+ #endif
+ int (*ndo_add_slave)(struct net_device *dev,
+ struct net_device *slave_dev,
--- /dev/null
+--- a/drivers/net/phy/Kconfig
++++ b/drivers/net/phy/Kconfig
+@@ -526,6 +526,13 @@ config MDIO_IPQ40XX
+ This driver supports the MDIO interface found in Qualcomm
+ Atheros ipq40xx Soc chip.
+
++config AR40XX_PHY
++ tristate "Driver for Qualcomm Atheros IPQ40XX switches"
++ depends on HAS_IOMEM && OF
++ select SWCONFIG
++ ---help---
++ This is the driver for Qualcomm Atheros IPQ40XX ESS switches.
++
+ endif # PHYLIB
+
+ config MICREL_KS8995MA
+--- a/drivers/net/phy/Makefile
++++ b/drivers/net/phy/Makefile
+@@ -62,6 +62,7 @@ obj-y += $(sfp-obj-y) $(sfp-obj-m)
+
+ obj-$(CONFIG_AMD_PHY) += amd.o
+ obj-$(CONFIG_AQUANTIA_PHY) += aquantia.o
++obj-$(CONFIG_AR40XX_PHY) += ar40xx.o
+ obj-$(CONFIG_AX88796B_PHY) += ax88796b.o
+ obj-$(CONFIG_AT803X_PHY) += at803x.o
+ obj-$(CONFIG_BCM63XX_PHY) += bcm63xx.o
+--- /dev/null
++++ b/drivers/net/phy/ar40xx.c
+@@ -0,0 +1,2090 @@
++/*
++ * Copyright (c) 2016, The Linux Foundation. All rights reserved.
++ *
++ * Permission to use, copy, modify, and/or distribute this software for
++ * any purpose with or without fee is hereby granted, provided that the
++ * above copyright notice and this permission notice appear in all copies.
++ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
++ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
++ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
++ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
++ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
++ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT
++ * OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
++ */
++
++#include <linux/module.h>
++#include <linux/list.h>
++#include <linux/bitops.h>
++#include <linux/switch.h>
++#include <linux/delay.h>
++#include <linux/phy.h>
++#include <linux/clk.h>
++#include <linux/reset.h>
++#include <linux/lockdep.h>
++#include <linux/workqueue.h>
++#include <linux/of_device.h>
++#include <linux/of_address.h>
++#include <linux/mdio.h>
++#include <linux/gpio.h>
++
++#include "ar40xx.h"
++
++static struct ar40xx_priv *ar40xx_priv;
++
++#define MIB_DESC(_s , _o, _n) \
++ { \
++ .size = (_s), \
++ .offset = (_o), \
++ .name = (_n), \
++ }
++
++static const struct ar40xx_mib_desc ar40xx_mibs[] = {
++ MIB_DESC(1, AR40XX_STATS_RXBROAD, "RxBroad"),
++ MIB_DESC(1, AR40XX_STATS_RXPAUSE, "RxPause"),
++ MIB_DESC(1, AR40XX_STATS_RXMULTI, "RxMulti"),
++ MIB_DESC(1, AR40XX_STATS_RXFCSERR, "RxFcsErr"),
++ MIB_DESC(1, AR40XX_STATS_RXALIGNERR, "RxAlignErr"),
++ MIB_DESC(1, AR40XX_STATS_RXRUNT, "RxRunt"),
++ MIB_DESC(1, AR40XX_STATS_RXFRAGMENT, "RxFragment"),
++ MIB_DESC(1, AR40XX_STATS_RX64BYTE, "Rx64Byte"),
++ MIB_DESC(1, AR40XX_STATS_RX128BYTE, "Rx128Byte"),
++ MIB_DESC(1, AR40XX_STATS_RX256BYTE, "Rx256Byte"),
++ MIB_DESC(1, AR40XX_STATS_RX512BYTE, "Rx512Byte"),
++ MIB_DESC(1, AR40XX_STATS_RX1024BYTE, "Rx1024Byte"),
++ MIB_DESC(1, AR40XX_STATS_RX1518BYTE, "Rx1518Byte"),
++ MIB_DESC(1, AR40XX_STATS_RXMAXBYTE, "RxMaxByte"),
++ MIB_DESC(1, AR40XX_STATS_RXTOOLONG, "RxTooLong"),
++ MIB_DESC(2, AR40XX_STATS_RXGOODBYTE, "RxGoodByte"),
++ MIB_DESC(2, AR40XX_STATS_RXBADBYTE, "RxBadByte"),
++ MIB_DESC(1, AR40XX_STATS_RXOVERFLOW, "RxOverFlow"),
++ MIB_DESC(1, AR40XX_STATS_FILTERED, "Filtered"),
++ MIB_DESC(1, AR40XX_STATS_TXBROAD, "TxBroad"),
++ MIB_DESC(1, AR40XX_STATS_TXPAUSE, "TxPause"),
++ MIB_DESC(1, AR40XX_STATS_TXMULTI, "TxMulti"),
++ MIB_DESC(1, AR40XX_STATS_TXUNDERRUN, "TxUnderRun"),
++ MIB_DESC(1, AR40XX_STATS_TX64BYTE, "Tx64Byte"),
++ MIB_DESC(1, AR40XX_STATS_TX128BYTE, "Tx128Byte"),
++ MIB_DESC(1, AR40XX_STATS_TX256BYTE, "Tx256Byte"),
++ MIB_DESC(1, AR40XX_STATS_TX512BYTE, "Tx512Byte"),
++ MIB_DESC(1, AR40XX_STATS_TX1024BYTE, "Tx1024Byte"),
++ MIB_DESC(1, AR40XX_STATS_TX1518BYTE, "Tx1518Byte"),
++ MIB_DESC(1, AR40XX_STATS_TXMAXBYTE, "TxMaxByte"),
++ MIB_DESC(1, AR40XX_STATS_TXOVERSIZE, "TxOverSize"),
++ MIB_DESC(2, AR40XX_STATS_TXBYTE, "TxByte"),
++ MIB_DESC(1, AR40XX_STATS_TXCOLLISION, "TxCollision"),
++ MIB_DESC(1, AR40XX_STATS_TXABORTCOL, "TxAbortCol"),
++ MIB_DESC(1, AR40XX_STATS_TXMULTICOL, "TxMultiCol"),
++ MIB_DESC(1, AR40XX_STATS_TXSINGLECOL, "TxSingleCol"),
++ MIB_DESC(1, AR40XX_STATS_TXEXCDEFER, "TxExcDefer"),
++ MIB_DESC(1, AR40XX_STATS_TXDEFER, "TxDefer"),
++ MIB_DESC(1, AR40XX_STATS_TXLATECOL, "TxLateCol"),
++};
++
++static u32
++ar40xx_read(struct ar40xx_priv *priv, int reg)
++{
++ return readl(priv->hw_addr + reg);
++}
++
++static u32
++ar40xx_psgmii_read(struct ar40xx_priv *priv, int reg)
++{
++ return readl(priv->psgmii_hw_addr + reg);
++}
++
++static void
++ar40xx_write(struct ar40xx_priv *priv, int reg, u32 val)
++{
++ writel(val, priv->hw_addr + reg);
++}
++
++static u32
++ar40xx_rmw(struct ar40xx_priv *priv, int reg, u32 mask, u32 val)
++{
++ u32 ret;
++
++ ret = ar40xx_read(priv, reg);
++ ret &= ~mask;
++ ret |= val;
++ ar40xx_write(priv, reg, ret);
++ return ret;
++}
++
++static void
++ar40xx_psgmii_write(struct ar40xx_priv *priv, int reg, u32 val)
++{
++ writel(val, priv->psgmii_hw_addr + reg);
++}
++
++static void
++ar40xx_phy_dbg_write(struct ar40xx_priv *priv, int phy_addr,
++ u16 dbg_addr, u16 dbg_data)
++{
++ struct mii_bus *bus = priv->mii_bus;
++
++ mutex_lock(&bus->mdio_lock);
++ bus->write(bus, phy_addr, AR40XX_MII_ATH_DBG_ADDR, dbg_addr);
++ bus->write(bus, phy_addr, AR40XX_MII_ATH_DBG_DATA, dbg_data);
++ mutex_unlock(&bus->mdio_lock);
++}
++
++static void
++ar40xx_phy_dbg_read(struct ar40xx_priv *priv, int phy_addr,
++ u16 dbg_addr, u16 *dbg_data)
++{
++ struct mii_bus *bus = priv->mii_bus;
++
++ mutex_lock(&bus->mdio_lock);
++ bus->write(bus, phy_addr, AR40XX_MII_ATH_DBG_ADDR, dbg_addr);
++ *dbg_data = bus->read(bus, phy_addr, AR40XX_MII_ATH_DBG_DATA);
++ mutex_unlock(&bus->mdio_lock);
++}
++
++static void
++ar40xx_phy_mmd_write(struct ar40xx_priv *priv, u32 phy_id,
++ u16 mmd_num, u16 reg_id, u16 reg_val)
++{
++ struct mii_bus *bus = priv->mii_bus;
++
++ mutex_lock(&bus->mdio_lock);
++ bus->write(bus, phy_id,
++ AR40XX_MII_ATH_MMD_ADDR, mmd_num);
++ bus->write(bus, phy_id,
++ AR40XX_MII_ATH_MMD_DATA, reg_id);
++ bus->write(bus, phy_id,
++ AR40XX_MII_ATH_MMD_ADDR,
++ 0x4000 | mmd_num);
++ bus->write(bus, phy_id,
++ AR40XX_MII_ATH_MMD_DATA, reg_val);
++ mutex_unlock(&bus->mdio_lock);
++}
++
++static u16
++ar40xx_phy_mmd_read(struct ar40xx_priv *priv, u32 phy_id,
++ u16 mmd_num, u16 reg_id)
++{
++ u16 value;
++ struct mii_bus *bus = priv->mii_bus;
++
++ mutex_lock(&bus->mdio_lock);
++ bus->write(bus, phy_id,
++ AR40XX_MII_ATH_MMD_ADDR, mmd_num);
++ bus->write(bus, phy_id,
++ AR40XX_MII_ATH_MMD_DATA, reg_id);
++ bus->write(bus, phy_id,
++ AR40XX_MII_ATH_MMD_ADDR,
++ 0x4000 | mmd_num);
++ value = bus->read(bus, phy_id, AR40XX_MII_ATH_MMD_DATA);
++ mutex_unlock(&bus->mdio_lock);
++ return value;
++}
++
++/* Start of swconfig support */
++
++static void
++ar40xx_phy_poll_reset(struct ar40xx_priv *priv)
++{
++ u32 i, in_reset, retries = 500;
++ struct mii_bus *bus = priv->mii_bus;
++
++ /* Assume RESET was recently issued to some or all of the phys */
++ in_reset = GENMASK(AR40XX_NUM_PHYS - 1, 0);
++
++ while (retries--) {
++ /* 1ms should be plenty of time.
++ * 802.3 spec allows for a max wait time of 500ms
++ */
++ usleep_range(1000, 2000);
++
++ for (i = 0; i < AR40XX_NUM_PHYS; i++) {
++ int val;
++
++ /* skip devices which have completed reset */
++ if (!(in_reset & BIT(i)))
++ continue;
++
++ val = mdiobus_read(bus, i, MII_BMCR);
++ if (val < 0)
++ continue;
++
++ /* mark when phy is no longer in reset state */
++ if (!(val & BMCR_RESET))
++ in_reset &= ~BIT(i);
++ }
++
++ if (!in_reset)
++ return;
++ }
++
++ dev_warn(&bus->dev, "Failed to reset all phys! (in_reset: 0x%x)\n",
++ in_reset);
++}
++
++static void
++ar40xx_phy_init(struct ar40xx_priv *priv)
++{
++ int i;
++ struct mii_bus *bus;
++ u16 val;
++
++ bus = priv->mii_bus;
++ for (i = 0; i < AR40XX_NUM_PORTS - 1; i++) {
++ ar40xx_phy_dbg_read(priv, i, AR40XX_PHY_DEBUG_0, &val);
++ val &= ~AR40XX_PHY_MANU_CTRL_EN;
++ ar40xx_phy_dbg_write(priv, i, AR40XX_PHY_DEBUG_0, val);
++ mdiobus_write(bus, i,
++ MII_ADVERTISE, ADVERTISE_ALL |
++ ADVERTISE_PAUSE_CAP |
++ ADVERTISE_PAUSE_ASYM);
++ mdiobus_write(bus, i, MII_CTRL1000, ADVERTISE_1000FULL);
++ mdiobus_write(bus, i, MII_BMCR, BMCR_RESET | BMCR_ANENABLE);
++ }
++
++ ar40xx_phy_poll_reset(priv);
++}
++
++static void
++ar40xx_port_phy_linkdown(struct ar40xx_priv *priv)
++{
++ struct mii_bus *bus;
++ int i;
++ u16 val;
++
++ bus = priv->mii_bus;
++ for (i = 0; i < AR40XX_NUM_PORTS - 1; i++) {
++ mdiobus_write(bus, i, MII_CTRL1000, 0);
++ mdiobus_write(bus, i, MII_ADVERTISE, 0);
++ mdiobus_write(bus, i, MII_BMCR, BMCR_RESET | BMCR_ANENABLE);
++ ar40xx_phy_dbg_read(priv, i, AR40XX_PHY_DEBUG_0, &val);
++ val |= AR40XX_PHY_MANU_CTRL_EN;
++ ar40xx_phy_dbg_write(priv, i, AR40XX_PHY_DEBUG_0, val);
++ /* disable transmit */
++ ar40xx_phy_dbg_read(priv, i, AR40XX_PHY_DEBUG_2, &val);
++ val &= 0xf00f;
++ ar40xx_phy_dbg_write(priv, i, AR40XX_PHY_DEBUG_2, val);
++ }
++}
++
++static void
++ar40xx_set_mirror_regs(struct ar40xx_priv *priv)
++{
++ int port;
++
++ /* reset all mirror registers */
++ ar40xx_rmw(priv, AR40XX_REG_FWD_CTRL0,
++ AR40XX_FWD_CTRL0_MIRROR_PORT,
++ (0xF << AR40XX_FWD_CTRL0_MIRROR_PORT_S));
++ for (port = 0; port < AR40XX_NUM_PORTS; port++) {
++ ar40xx_rmw(priv, AR40XX_REG_PORT_LOOKUP(port),
++ AR40XX_PORT_LOOKUP_ING_MIRROR_EN, 0);
++
++ ar40xx_rmw(priv, AR40XX_REG_PORT_HOL_CTRL1(port),
++ AR40XX_PORT_HOL_CTRL1_EG_MIRROR_EN, 0);
++ }
++
++ /* now enable mirroring if necessary */
++ if (priv->source_port >= AR40XX_NUM_PORTS ||
++ priv->monitor_port >= AR40XX_NUM_PORTS ||
++ priv->source_port == priv->monitor_port) {
++ return;
++ }
++
++ ar40xx_rmw(priv, AR40XX_REG_FWD_CTRL0,
++ AR40XX_FWD_CTRL0_MIRROR_PORT,
++ (priv->monitor_port << AR40XX_FWD_CTRL0_MIRROR_PORT_S));
++
++ if (priv->mirror_rx)
++ ar40xx_rmw(priv, AR40XX_REG_PORT_LOOKUP(priv->source_port), 0,
++ AR40XX_PORT_LOOKUP_ING_MIRROR_EN);
++
++ if (priv->mirror_tx)
++ ar40xx_rmw(priv, AR40XX_REG_PORT_HOL_CTRL1(priv->source_port),
++ 0, AR40XX_PORT_HOL_CTRL1_EG_MIRROR_EN);
++}
++
++static int
++ar40xx_sw_get_ports(struct switch_dev *dev, struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++ u8 ports = priv->vlan_table[val->port_vlan];
++ int i;
++
++ val->len = 0;
++ for (i = 0; i < dev->ports; i++) {
++ struct switch_port *p;
++
++ if (!(ports & BIT(i)))
++ continue;
++
++ p = &val->value.ports[val->len++];
++ p->id = i;
++ if ((priv->vlan_tagged & BIT(i)) ||
++ (priv->pvid[i] != val->port_vlan))
++ p->flags = BIT(SWITCH_PORT_FLAG_TAGGED);
++ else
++ p->flags = 0;
++ }
++ return 0;
++}
++
++static int
++ar40xx_sw_set_ports(struct switch_dev *dev, struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++ u8 *vt = &priv->vlan_table[val->port_vlan];
++ int i;
++
++ *vt = 0;
++ for (i = 0; i < val->len; i++) {
++ struct switch_port *p = &val->value.ports[i];
++
++ if (p->flags & BIT(SWITCH_PORT_FLAG_TAGGED)) {
++ if (val->port_vlan == priv->pvid[p->id])
++ priv->vlan_tagged |= BIT(p->id);
++ } else {
++ priv->vlan_tagged &= ~BIT(p->id);
++ priv->pvid[p->id] = val->port_vlan;
++ }
++
++ *vt |= BIT(p->id);
++ }
++ return 0;
++}
++
++static int
++ar40xx_reg_wait(struct ar40xx_priv *priv, u32 reg, u32 mask, u32 val,
++ unsigned timeout)
++{
++ int i;
++
++ for (i = 0; i < timeout; i++) {
++ u32 t;
++
++ t = ar40xx_read(priv, reg);
++ if ((t & mask) == val)
++ return 0;
++
++ usleep_range(1000, 2000);
++ }
++
++ return -ETIMEDOUT;
++}
++
++static int
++ar40xx_mib_op(struct ar40xx_priv *priv, u32 op)
++{
++ int ret;
++
++ lockdep_assert_held(&priv->mib_lock);
++
++ /* Capture the hardware statistics for all ports */
++ ar40xx_rmw(priv, AR40XX_REG_MIB_FUNC,
++ AR40XX_MIB_FUNC, (op << AR40XX_MIB_FUNC_S));
++
++ /* Wait for the capturing to complete. */
++ ret = ar40xx_reg_wait(priv, AR40XX_REG_MIB_FUNC,
++ AR40XX_MIB_BUSY, 0, 10);
++
++ return ret;
++}
++
++static void
++ar40xx_mib_fetch_port_stat(struct ar40xx_priv *priv, int port, bool flush)
++{
++ unsigned int base;
++ u64 *mib_stats;
++ int i;
++ u32 num_mibs = ARRAY_SIZE(ar40xx_mibs);
++
++ WARN_ON(port >= priv->dev.ports);
++
++ lockdep_assert_held(&priv->mib_lock);
++
++ base = AR40XX_REG_PORT_STATS_START +
++ AR40XX_REG_PORT_STATS_LEN * port;
++
++ mib_stats = &priv->mib_stats[port * num_mibs];
++ if (flush) {
++ u32 len;
++
++ len = num_mibs * sizeof(*mib_stats);
++ memset(mib_stats, 0, len);
++ return;
++ }
++ for (i = 0; i < num_mibs; i++) {
++ const struct ar40xx_mib_desc *mib;
++ u64 t;
++
++ mib = &ar40xx_mibs[i];
++ t = ar40xx_read(priv, base + mib->offset);
++ if (mib->size == 2) {
++ u64 hi;
++
++ hi = ar40xx_read(priv, base + mib->offset + 4);
++ t |= hi << 32;
++ }
++
++ mib_stats[i] += t;
++ }
++}
++
++static int
++ar40xx_mib_capture(struct ar40xx_priv *priv)
++{
++ return ar40xx_mib_op(priv, AR40XX_MIB_FUNC_CAPTURE);
++}
++
++static int
++ar40xx_mib_flush(struct ar40xx_priv *priv)
++{
++ return ar40xx_mib_op(priv, AR40XX_MIB_FUNC_FLUSH);
++}
++
++static int
++ar40xx_sw_set_reset_mibs(struct switch_dev *dev,
++ const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++ unsigned int len;
++ int ret;
++ u32 num_mibs = ARRAY_SIZE(ar40xx_mibs);
++
++ mutex_lock(&priv->mib_lock);
++
++ len = priv->dev.ports * num_mibs * sizeof(*priv->mib_stats);
++ memset(priv->mib_stats, 0, len);
++ ret = ar40xx_mib_flush(priv);
++
++ mutex_unlock(&priv->mib_lock);
++ return ret;
++}
++
++static int
++ar40xx_sw_set_vlan(struct switch_dev *dev, const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ priv->vlan = !!val->value.i;
++ return 0;
++}
++
++static int
++ar40xx_sw_get_vlan(struct switch_dev *dev, const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ val->value.i = priv->vlan;
++ return 0;
++}
++
++static int
++ar40xx_sw_set_mirror_rx_enable(struct switch_dev *dev,
++ const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ mutex_lock(&priv->reg_mutex);
++ priv->mirror_rx = !!val->value.i;
++ ar40xx_set_mirror_regs(priv);
++ mutex_unlock(&priv->reg_mutex);
++
++ return 0;
++}
++
++static int
++ar40xx_sw_get_mirror_rx_enable(struct switch_dev *dev,
++ const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ mutex_lock(&priv->reg_mutex);
++ val->value.i = priv->mirror_rx;
++ mutex_unlock(&priv->reg_mutex);
++ return 0;
++}
++
++static int
++ar40xx_sw_set_mirror_tx_enable(struct switch_dev *dev,
++ const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ mutex_lock(&priv->reg_mutex);
++ priv->mirror_tx = !!val->value.i;
++ ar40xx_set_mirror_regs(priv);
++ mutex_unlock(&priv->reg_mutex);
++
++ return 0;
++}
++
++static int
++ar40xx_sw_get_mirror_tx_enable(struct switch_dev *dev,
++ const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ mutex_lock(&priv->reg_mutex);
++ val->value.i = priv->mirror_tx;
++ mutex_unlock(&priv->reg_mutex);
++ return 0;
++}
++
++static int
++ar40xx_sw_set_mirror_monitor_port(struct switch_dev *dev,
++ const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ mutex_lock(&priv->reg_mutex);
++ priv->monitor_port = val->value.i;
++ ar40xx_set_mirror_regs(priv);
++ mutex_unlock(&priv->reg_mutex);
++
++ return 0;
++}
++
++static int
++ar40xx_sw_get_mirror_monitor_port(struct switch_dev *dev,
++ const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ mutex_lock(&priv->reg_mutex);
++ val->value.i = priv->monitor_port;
++ mutex_unlock(&priv->reg_mutex);
++ return 0;
++}
++
++static int
++ar40xx_sw_set_mirror_source_port(struct switch_dev *dev,
++ const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ mutex_lock(&priv->reg_mutex);
++ priv->source_port = val->value.i;
++ ar40xx_set_mirror_regs(priv);
++ mutex_unlock(&priv->reg_mutex);
++
++ return 0;
++}
++
++static int
++ar40xx_sw_get_mirror_source_port(struct switch_dev *dev,
++ const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ mutex_lock(&priv->reg_mutex);
++ val->value.i = priv->source_port;
++ mutex_unlock(&priv->reg_mutex);
++ return 0;
++}
++
++static int
++ar40xx_sw_set_linkdown(struct switch_dev *dev,
++ const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ if (val->value.i == 1)
++ ar40xx_port_phy_linkdown(priv);
++ else
++ ar40xx_phy_init(priv);
++
++ return 0;
++}
++
++static int
++ar40xx_sw_set_port_reset_mib(struct switch_dev *dev,
++ const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++ int port;
++ int ret;
++
++ port = val->port_vlan;
++ if (port >= dev->ports)
++ return -EINVAL;
++
++ mutex_lock(&priv->mib_lock);
++ ret = ar40xx_mib_capture(priv);
++ if (ret)
++ goto unlock;
++
++ ar40xx_mib_fetch_port_stat(priv, port, true);
++
++unlock:
++ mutex_unlock(&priv->mib_lock);
++ return ret;
++}
++
++static int
++ar40xx_sw_get_port_mib(struct switch_dev *dev,
++ const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++ u64 *mib_stats;
++ int port;
++ int ret;
++ char *buf = priv->buf;
++ int i, len = 0;
++ u32 num_mibs = ARRAY_SIZE(ar40xx_mibs);
++
++ port = val->port_vlan;
++ if (port >= dev->ports)
++ return -EINVAL;
++
++ mutex_lock(&priv->mib_lock);
++ ret = ar40xx_mib_capture(priv);
++ if (ret)
++ goto unlock;
++
++ ar40xx_mib_fetch_port_stat(priv, port, false);
++
++ len += snprintf(buf + len, sizeof(priv->buf) - len,
++ "Port %d MIB counters\n",
++ port);
++
++ mib_stats = &priv->mib_stats[port * num_mibs];
++ for (i = 0; i < num_mibs; i++)
++ len += snprintf(buf + len, sizeof(priv->buf) - len,
++ "%-12s: %llu\n",
++ ar40xx_mibs[i].name,
++ mib_stats[i]);
++
++ val->value.s = buf;
++ val->len = len;
++
++unlock:
++ mutex_unlock(&priv->mib_lock);
++ return ret;
++}
++
++static int
++ar40xx_sw_set_vid(struct switch_dev *dev, const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ priv->vlan_id[val->port_vlan] = val->value.i;
++ return 0;
++}
++
++static int
++ar40xx_sw_get_vid(struct switch_dev *dev, const struct switch_attr *attr,
++ struct switch_val *val)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ val->value.i = priv->vlan_id[val->port_vlan];
++ return 0;
++}
++
++static int
++ar40xx_sw_get_pvid(struct switch_dev *dev, int port, int *vlan)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++ *vlan = priv->pvid[port];
++ return 0;
++}
++
++static int
++ar40xx_sw_set_pvid(struct switch_dev *dev, int port, int vlan)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ /* make sure no invalid PVIDs get set */
++ if (vlan >= dev->vlans)
++ return -EINVAL;
++
++ priv->pvid[port] = vlan;
++ return 0;
++}
++
++static void
++ar40xx_read_port_link(struct ar40xx_priv *priv, int port,
++ struct switch_port_link *link)
++{
++ u32 status;
++ u32 speed;
++
++ memset(link, 0, sizeof(*link));
++
++ status = ar40xx_read(priv, AR40XX_REG_PORT_STATUS(port));
++
++ link->aneg = !!(status & AR40XX_PORT_AUTO_LINK_EN);
++ if (link->aneg || (port != AR40XX_PORT_CPU))
++ link->link = !!(status & AR40XX_PORT_STATUS_LINK_UP);
++ else
++ link->link = true;
++
++ if (!link->link)
++ return;
++
++ link->duplex = !!(status & AR40XX_PORT_DUPLEX);
++ link->tx_flow = !!(status & AR40XX_PORT_STATUS_TXFLOW);
++ link->rx_flow = !!(status & AR40XX_PORT_STATUS_RXFLOW);
++
++ speed = (status & AR40XX_PORT_SPEED) >>
++ AR40XX_PORT_STATUS_SPEED_S;
++
++ switch (speed) {
++ case AR40XX_PORT_SPEED_10M:
++ link->speed = SWITCH_PORT_SPEED_10;
++ break;
++ case AR40XX_PORT_SPEED_100M:
++ link->speed = SWITCH_PORT_SPEED_100;
++ break;
++ case AR40XX_PORT_SPEED_1000M:
++ link->speed = SWITCH_PORT_SPEED_1000;
++ break;
++ default:
++ link->speed = SWITCH_PORT_SPEED_UNKNOWN;
++ break;
++ }
++}
++
++static int
++ar40xx_sw_get_port_link(struct switch_dev *dev, int port,
++ struct switch_port_link *link)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++
++ ar40xx_read_port_link(priv, port, link);
++ return 0;
++}
++
++static const struct switch_attr ar40xx_sw_attr_globals[] = {
++ {
++ .type = SWITCH_TYPE_INT,
++ .name = "enable_vlan",
++ .description = "Enable VLAN mode",
++ .set = ar40xx_sw_set_vlan,
++ .get = ar40xx_sw_get_vlan,
++ .max = 1
++ },
++ {
++ .type = SWITCH_TYPE_NOVAL,
++ .name = "reset_mibs",
++ .description = "Reset all MIB counters",
++ .set = ar40xx_sw_set_reset_mibs,
++ },
++ {
++ .type = SWITCH_TYPE_INT,
++ .name = "enable_mirror_rx",
++ .description = "Enable mirroring of RX packets",
++ .set = ar40xx_sw_set_mirror_rx_enable,
++ .get = ar40xx_sw_get_mirror_rx_enable,
++ .max = 1
++ },
++ {
++ .type = SWITCH_TYPE_INT,
++ .name = "enable_mirror_tx",
++ .description = "Enable mirroring of TX packets",
++ .set = ar40xx_sw_set_mirror_tx_enable,
++ .get = ar40xx_sw_get_mirror_tx_enable,
++ .max = 1
++ },
++ {
++ .type = SWITCH_TYPE_INT,
++ .name = "mirror_monitor_port",
++ .description = "Mirror monitor port",
++ .set = ar40xx_sw_set_mirror_monitor_port,
++ .get = ar40xx_sw_get_mirror_monitor_port,
++ .max = AR40XX_NUM_PORTS - 1
++ },
++ {
++ .type = SWITCH_TYPE_INT,
++ .name = "mirror_source_port",
++ .description = "Mirror source port",
++ .set = ar40xx_sw_set_mirror_source_port,
++ .get = ar40xx_sw_get_mirror_source_port,
++ .max = AR40XX_NUM_PORTS - 1
++ },
++ {
++ .type = SWITCH_TYPE_INT,
++ .name = "linkdown",
++ .description = "Link down all the PHYs",
++ .set = ar40xx_sw_set_linkdown,
++ .max = 1
++ },
++};
++
++static const struct switch_attr ar40xx_sw_attr_port[] = {
++ {
++ .type = SWITCH_TYPE_NOVAL,
++ .name = "reset_mib",
++ .description = "Reset single port MIB counters",
++ .set = ar40xx_sw_set_port_reset_mib,
++ },
++ {
++ .type = SWITCH_TYPE_STRING,
++ .name = "mib",
++ .description = "Get port's MIB counters",
++ .set = NULL,
++ .get = ar40xx_sw_get_port_mib,
++ },
++};
++
++const struct switch_attr ar40xx_sw_attr_vlan[] = {
++ {
++ .type = SWITCH_TYPE_INT,
++ .name = "vid",
++ .description = "VLAN ID (0-4094)",
++ .set = ar40xx_sw_set_vid,
++ .get = ar40xx_sw_get_vid,
++ .max = 4094,
++ },
++};
++
++/* End of swconfig support */
++
++static int
++ar40xx_wait_bit(struct ar40xx_priv *priv, int reg, u32 mask, u32 val)
++{
++ int timeout = 20;
++ u32 t;
++
++ while (1) {
++ t = ar40xx_read(priv, reg);
++ if ((t & mask) == val)
++ return 0;
++
++ if (timeout-- <= 0)
++ break;
++
++ usleep_range(10, 20);
++ }
++
++ pr_err("ar40xx: timeout for reg %08x: %08x & %08x != %08x\n",
++ (unsigned int)reg, t, mask, val);
++ return -ETIMEDOUT;
++}
++
++static int
++ar40xx_atu_flush(struct ar40xx_priv *priv)
++{
++ int ret;
++
++ ret = ar40xx_wait_bit(priv, AR40XX_REG_ATU_FUNC,
++ AR40XX_ATU_FUNC_BUSY, 0);
++ if (!ret)
++ ar40xx_write(priv, AR40XX_REG_ATU_FUNC,
++ AR40XX_ATU_FUNC_OP_FLUSH |
++ AR40XX_ATU_FUNC_BUSY);
++
++ return ret;
++}
++
++static void
++ar40xx_ess_reset(struct ar40xx_priv *priv)
++{
++ reset_control_assert(priv->ess_rst);
++ mdelay(10);
++ reset_control_deassert(priv->ess_rst);
++ /* Waiting for all inner tables init done.
++ * It cost 5~10ms.
++ */
++ mdelay(10);
++
++ pr_info("ESS reset ok!\n");
++}
++
++/* Start of psgmii self test */
++
++static void
++ar40xx_malibu_psgmii_ess_reset(struct ar40xx_priv *priv)
++{
++ u32 n;
++ struct mii_bus *bus = priv->mii_bus;
++ /* reset phy psgmii */
++ /* fix phy psgmii RX 20bit */
++ mdiobus_write(bus, 5, 0x0, 0x005b);
++ /* reset phy psgmii */
++ mdiobus_write(bus, 5, 0x0, 0x001b);
++ /* release reset phy psgmii */
++ mdiobus_write(bus, 5, 0x0, 0x005b);
++
++ for (n = 0; n < AR40XX_PSGMII_CALB_NUM; n++) {
++ u16 status;
++
++ status = ar40xx_phy_mmd_read(priv, 5, 1, 0x28);
++ if (status & BIT(0))
++ break;
++ /* Polling interval to check PSGMII PLL in malibu is ready
++ * the worst time is 8.67ms
++ * for 25MHz reference clock
++ * [512+(128+2048)*49]*80ns+100us
++ */
++ mdelay(2);
++ }
++
++ /*check malibu psgmii calibration done end..*/
++
++ /*freeze phy psgmii RX CDR*/
++ mdiobus_write(bus, 5, 0x1a, 0x2230);
++
++ ar40xx_ess_reset(priv);
++
++ /*check psgmii calibration done start*/
++ for (n = 0; n < AR40XX_PSGMII_CALB_NUM; n++) {
++ u32 status;
++
++ status = ar40xx_psgmii_read(priv, 0xa0);
++ if (status & BIT(0))
++ break;
++ /* Polling interval to check PSGMII PLL in ESS is ready */
++ mdelay(2);
++ }
++
++ /* check dakota psgmii calibration done end..*/
++
++ /* relesae phy psgmii RX CDR */
++ mdiobus_write(bus, 5, 0x1a, 0x3230);
++ /* release phy psgmii RX 20bit */
++ mdiobus_write(bus, 5, 0x0, 0x005f);
++}
++
++static void
++ar40xx_psgmii_single_phy_testing(struct ar40xx_priv *priv, int phy)
++{
++ int j;
++ u32 tx_ok, tx_error;
++ u32 rx_ok, rx_error;
++ u32 tx_ok_high16;
++ u32 rx_ok_high16;
++ u32 tx_all_ok, rx_all_ok;
++ struct mii_bus *bus = priv->mii_bus;
++
++ mdiobus_write(bus, phy, 0x0, 0x9000);
++ mdiobus_write(bus, phy, 0x0, 0x4140);
++
++ for (j = 0; j < AR40XX_PSGMII_CALB_NUM; j++) {
++ u16 status;
++
++ status = mdiobus_read(bus, phy, 0x11);
++ if (status & AR40XX_PHY_SPEC_STATUS_LINK)
++ break;
++ /* the polling interval to check if the PHY link up or not
++ * maxwait_timer: 750 ms +/-10 ms
++ * minwait_timer : 1 us +/- 0.1us
++ * time resides in minwait_timer ~ maxwait_timer
++ * see IEEE 802.3 section 40.4.5.2
++ */
++ mdelay(8);
++ }
++
++ /* enable check */
++ ar40xx_phy_mmd_write(priv, phy, 7, 0x8029, 0x0000);
++ ar40xx_phy_mmd_write(priv, phy, 7, 0x8029, 0x0003);
++
++ /* start traffic */
++ ar40xx_phy_mmd_write(priv, phy, 7, 0x8020, 0xa000);
++ /* wait for all traffic end
++ * 4096(pkt num)*1524(size)*8ns(125MHz)=49.9ms
++ */
++ mdelay(50);
++
++ /* check counter */
++ tx_ok = ar40xx_phy_mmd_read(priv, phy, 7, 0x802e);
++ tx_ok_high16 = ar40xx_phy_mmd_read(priv, phy, 7, 0x802d);
++ tx_error = ar40xx_phy_mmd_read(priv, phy, 7, 0x802f);
++ rx_ok = ar40xx_phy_mmd_read(priv, phy, 7, 0x802b);
++ rx_ok_high16 = ar40xx_phy_mmd_read(priv, phy, 7, 0x802a);
++ rx_error = ar40xx_phy_mmd_read(priv, phy, 7, 0x802c);
++ tx_all_ok = tx_ok + (tx_ok_high16 << 16);
++ rx_all_ok = rx_ok + (rx_ok_high16 << 16);
++ if (tx_all_ok == 0x1000 && tx_error == 0) {
++ /* success */
++ priv->phy_t_status &= (~BIT(phy));
++ } else {
++ pr_info("PHY %d single test PSGMII issue happen!\n", phy);
++ priv->phy_t_status |= BIT(phy);
++ }
++
++ mdiobus_write(bus, phy, 0x0, 0x1840);
++}
++
++static void
++ar40xx_psgmii_all_phy_testing(struct ar40xx_priv *priv)
++{
++ int phy, j;
++ struct mii_bus *bus = priv->mii_bus;
++
++ mdiobus_write(bus, 0x1f, 0x0, 0x9000);
++ mdiobus_write(bus, 0x1f, 0x0, 0x4140);
++
++ for (j = 0; j < AR40XX_PSGMII_CALB_NUM; j++) {
++ for (phy = 0; phy < AR40XX_NUM_PORTS - 1; phy++) {
++ u16 status;
++
++ status = mdiobus_read(bus, phy, 0x11);
++ if (!(status & BIT(10)))
++ break;
++ }
++
++ if (phy >= (AR40XX_NUM_PORTS - 1))
++ break;
++ /* The polling interva to check if the PHY link up or not */
++ mdelay(8);
++ }
++ /* enable check */
++ ar40xx_phy_mmd_write(priv, 0x1f, 7, 0x8029, 0x0000);
++ ar40xx_phy_mmd_write(priv, 0x1f, 7, 0x8029, 0x0003);
++
++ /* start traffic */
++ ar40xx_phy_mmd_write(priv, 0x1f, 7, 0x8020, 0xa000);
++ /* wait for all traffic end
++ * 4096(pkt num)*1524(size)*8ns(125MHz)=49.9ms
++ */
++ mdelay(50);
++
++ for (phy = 0; phy < AR40XX_NUM_PORTS - 1; phy++) {
++ u32 tx_ok, tx_error;
++ u32 rx_ok, rx_error;
++ u32 tx_ok_high16;
++ u32 rx_ok_high16;
++ u32 tx_all_ok, rx_all_ok;
++
++ /* check counter */
++ tx_ok = ar40xx_phy_mmd_read(priv, phy, 7, 0x802e);
++ tx_ok_high16 = ar40xx_phy_mmd_read(priv, phy, 7, 0x802d);
++ tx_error = ar40xx_phy_mmd_read(priv, phy, 7, 0x802f);
++ rx_ok = ar40xx_phy_mmd_read(priv, phy, 7, 0x802b);
++ rx_ok_high16 = ar40xx_phy_mmd_read(priv, phy, 7, 0x802a);
++ rx_error = ar40xx_phy_mmd_read(priv, phy, 7, 0x802c);
++ tx_all_ok = tx_ok + (tx_ok_high16<<16);
++ rx_all_ok = rx_ok + (rx_ok_high16<<16);
++ if (tx_all_ok == 0x1000 && tx_error == 0) {
++ /* success */
++ priv->phy_t_status &= ~BIT(phy + 8);
++ } else {
++ pr_info("PHY%d test see issue!\n", phy);
++ priv->phy_t_status |= BIT(phy + 8);
++ }
++ }
++
++ pr_debug("PHY all test 0x%x \r\n", priv->phy_t_status);
++}
++
++void
++ar40xx_psgmii_self_test(struct ar40xx_priv *priv)
++{
++ u32 i, phy;
++ struct mii_bus *bus = priv->mii_bus;
++
++ ar40xx_malibu_psgmii_ess_reset(priv);
++
++ /* switch to access MII reg for copper */
++ mdiobus_write(bus, 4, 0x1f, 0x8500);
++ for (phy = 0; phy < AR40XX_NUM_PORTS - 1; phy++) {
++ /*enable phy mdio broadcast write*/
++ ar40xx_phy_mmd_write(priv, phy, 7, 0x8028, 0x801f);
++ }
++ /* force no link by power down */
++ mdiobus_write(bus, 0x1f, 0x0, 0x1840);
++ /*packet number*/
++ ar40xx_phy_mmd_write(priv, 0x1f, 7, 0x8021, 0x1000);
++ ar40xx_phy_mmd_write(priv, 0x1f, 7, 0x8062, 0x05e0);
++
++ /*fix mdi status */
++ mdiobus_write(bus, 0x1f, 0x10, 0x6800);
++ for (i = 0; i < AR40XX_PSGMII_CALB_NUM; i++) {
++ priv->phy_t_status = 0;
++
++ for (phy = 0; phy < AR40XX_NUM_PORTS - 1; phy++) {
++ ar40xx_rmw(priv, AR40XX_REG_PORT_LOOKUP(phy + 1),
++ AR40XX_PORT_LOOKUP_LOOPBACK,
++ AR40XX_PORT_LOOKUP_LOOPBACK);
++ }
++
++ for (phy = 0; phy < AR40XX_NUM_PORTS - 1; phy++)
++ ar40xx_psgmii_single_phy_testing(priv, phy);
++
++ ar40xx_psgmii_all_phy_testing(priv);
++
++ if (priv->phy_t_status)
++ ar40xx_malibu_psgmii_ess_reset(priv);
++ else
++ break;
++ }
++
++ if (i >= AR40XX_PSGMII_CALB_NUM)
++ pr_info("PSGMII cannot recover\n");
++ else
++ pr_debug("PSGMII recovered after %d times reset\n", i);
++
++ /* configuration recover */
++ /* packet number */
++ ar40xx_phy_mmd_write(priv, 0x1f, 7, 0x8021, 0x0);
++ /* disable check */
++ ar40xx_phy_mmd_write(priv, 0x1f, 7, 0x8029, 0x0);
++ /* disable traffic */
++ ar40xx_phy_mmd_write(priv, 0x1f, 7, 0x8020, 0x0);
++}
++
++void
++ar40xx_psgmii_self_test_clean(struct ar40xx_priv *priv)
++{
++ int phy;
++ struct mii_bus *bus = priv->mii_bus;
++
++ /* disable phy internal loopback */
++ mdiobus_write(bus, 0x1f, 0x10, 0x6860);
++ mdiobus_write(bus, 0x1f, 0x0, 0x9040);
++
++ for (phy = 0; phy < AR40XX_NUM_PORTS - 1; phy++) {
++ /* disable mac loop back */
++ ar40xx_rmw(priv, AR40XX_REG_PORT_LOOKUP(phy + 1),
++ AR40XX_PORT_LOOKUP_LOOPBACK, 0);
++ /* disable phy mdio broadcast write */
++ ar40xx_phy_mmd_write(priv, phy, 7, 0x8028, 0x001f);
++ }
++
++ /* clear fdb entry */
++ ar40xx_atu_flush(priv);
++}
++
++/* End of psgmii self test */
++
++static void
++ar40xx_mac_mode_init(struct ar40xx_priv *priv, u32 mode)
++{
++ if (mode == PORT_WRAPPER_PSGMII) {
++ ar40xx_psgmii_write(priv, AR40XX_PSGMII_MODE_CONTROL, 0x2200);
++ ar40xx_psgmii_write(priv, AR40XX_PSGMIIPHY_TX_CONTROL, 0x8380);
++ }
++}
++
++static
++int ar40xx_cpuport_setup(struct ar40xx_priv *priv)
++{
++ u32 t;
++
++ t = AR40XX_PORT_STATUS_TXFLOW |
++ AR40XX_PORT_STATUS_RXFLOW |
++ AR40XX_PORT_TXHALF_FLOW |
++ AR40XX_PORT_DUPLEX |
++ AR40XX_PORT_SPEED_1000M;
++ ar40xx_write(priv, AR40XX_REG_PORT_STATUS(0), t);
++ usleep_range(10, 20);
++
++ t |= AR40XX_PORT_TX_EN |
++ AR40XX_PORT_RX_EN;
++ ar40xx_write(priv, AR40XX_REG_PORT_STATUS(0), t);
++
++ return 0;
++}
++
++static void
++ar40xx_init_port(struct ar40xx_priv *priv, int port)
++{
++ u32 t;
++
++ ar40xx_rmw(priv, AR40XX_REG_PORT_STATUS(port),
++ AR40XX_PORT_AUTO_LINK_EN, 0);
++
++ ar40xx_write(priv, AR40XX_REG_PORT_HEADER(port), 0);
++
++ ar40xx_write(priv, AR40XX_REG_PORT_VLAN0(port), 0);
++
++ t = AR40XX_PORT_VLAN1_OUT_MODE_UNTOUCH << AR40XX_PORT_VLAN1_OUT_MODE_S;
++ ar40xx_write(priv, AR40XX_REG_PORT_VLAN1(port), t);
++
++ t = AR40XX_PORT_LOOKUP_LEARN;
++ t |= AR40XX_PORT_STATE_FORWARD << AR40XX_PORT_LOOKUP_STATE_S;
++ ar40xx_write(priv, AR40XX_REG_PORT_LOOKUP(port), t);
++}
++
++void
++ar40xx_init_globals(struct ar40xx_priv *priv)
++{
++ u32 t;
++
++ /* enable CPU port and disable mirror port */
++ t = AR40XX_FWD_CTRL0_CPU_PORT_EN |
++ AR40XX_FWD_CTRL0_MIRROR_PORT;
++ ar40xx_write(priv, AR40XX_REG_FWD_CTRL0, t);
++
++ /* forward multicast and broadcast frames to CPU */
++ t = (AR40XX_PORTS_ALL << AR40XX_FWD_CTRL1_UC_FLOOD_S) |
++ (AR40XX_PORTS_ALL << AR40XX_FWD_CTRL1_MC_FLOOD_S) |
++ (AR40XX_PORTS_ALL << AR40XX_FWD_CTRL1_BC_FLOOD_S);
++ ar40xx_write(priv, AR40XX_REG_FWD_CTRL1, t);
++
++ /* enable jumbo frames */
++ ar40xx_rmw(priv, AR40XX_REG_MAX_FRAME_SIZE,
++ AR40XX_MAX_FRAME_SIZE_MTU, 9018 + 8 + 2);
++
++ /* Enable MIB counters */
++ ar40xx_rmw(priv, AR40XX_REG_MODULE_EN, 0,
++ AR40XX_MODULE_EN_MIB);
++
++ /* Disable AZ */
++ ar40xx_write(priv, AR40XX_REG_EEE_CTRL, 0);
++
++ /* set flowctrl thershold for cpu port */
++ t = (AR40XX_PORT0_FC_THRESH_ON_DFLT << 16) |
++ AR40XX_PORT0_FC_THRESH_OFF_DFLT;
++ ar40xx_write(priv, AR40XX_REG_PORT_FLOWCTRL_THRESH(0), t);
++}
++
++static void
++ar40xx_malibu_init(struct ar40xx_priv *priv)
++{
++ int i;
++ struct mii_bus *bus;
++ u16 val;
++
++ bus = priv->mii_bus;
++
++ /* war to enable AZ transmitting ability */
++ ar40xx_phy_mmd_write(priv, AR40XX_PSGMII_ID, 1,
++ AR40XX_MALIBU_PSGMII_MODE_CTRL,
++ AR40XX_MALIBU_PHY_PSGMII_MODE_CTRL_ADJUST_VAL);
++ for (i = 0; i < AR40XX_NUM_PORTS - 1; i++) {
++ /* change malibu control_dac */
++ val = ar40xx_phy_mmd_read(priv, i, 7,
++ AR40XX_MALIBU_PHY_MMD7_DAC_CTRL);
++ val &= ~AR40XX_MALIBU_DAC_CTRL_MASK;
++ val |= AR40XX_MALIBU_DAC_CTRL_VALUE;
++ ar40xx_phy_mmd_write(priv, i, 7,
++ AR40XX_MALIBU_PHY_MMD7_DAC_CTRL, val);
++ if (i == AR40XX_MALIBU_PHY_LAST_ADDR) {
++ /* to avoid goes into hibernation */
++ val = ar40xx_phy_mmd_read(priv, i, 3,
++ AR40XX_MALIBU_PHY_RLP_CTRL);
++ val &= (~(1<<1));
++ ar40xx_phy_mmd_write(priv, i, 3,
++ AR40XX_MALIBU_PHY_RLP_CTRL, val);
++ }
++ }
++
++ /* adjust psgmii serdes tx amp */
++ mdiobus_write(bus, AR40XX_PSGMII_ID, AR40XX_PSGMII_TX_DRIVER_1_CTRL,
++ AR40XX_MALIBU_PHY_PSGMII_REDUCE_SERDES_TX_AMP);
++}
++
++static int
++ar40xx_hw_init(struct ar40xx_priv *priv)
++{
++ u32 i;
++
++ ar40xx_ess_reset(priv);
++
++ if (priv->mii_bus)
++ ar40xx_malibu_init(priv);
++ else
++ return -1;
++
++ ar40xx_psgmii_self_test(priv);
++ ar40xx_psgmii_self_test_clean(priv);
++
++ ar40xx_mac_mode_init(priv, priv->mac_mode);
++
++ for (i = 0; i < priv->dev.ports; i++)
++ ar40xx_init_port(priv, i);
++
++ ar40xx_init_globals(priv);
++
++ return 0;
++}
++
++/* Start of qm error WAR */
++
++static
++int ar40xx_force_1g_full(struct ar40xx_priv *priv, u32 port_id)
++{
++ u32 reg;
++
++ if (port_id < 0 || port_id > 6)
++ return -1;
++
++ reg = AR40XX_REG_PORT_STATUS(port_id);
++ return ar40xx_rmw(priv, reg, AR40XX_PORT_SPEED,
++ (AR40XX_PORT_SPEED_1000M | AR40XX_PORT_DUPLEX));
++}
++
++static
++int ar40xx_get_qm_status(struct ar40xx_priv *priv,
++ u32 port_id, u32 *qm_buffer_err)
++{
++ u32 reg;
++ u32 qm_val;
++
++ if (port_id < 1 || port_id > 5) {
++ *qm_buffer_err = 0;
++ return -1;
++ }
++
++ if (port_id < 4) {
++ reg = AR40XX_REG_QM_PORT0_3_QNUM;
++ ar40xx_write(priv, AR40XX_REG_QM_DEBUG_ADDR, reg);
++ qm_val = ar40xx_read(priv, AR40XX_REG_QM_DEBUG_VALUE);
++ /* every 8 bits for each port */
++ *qm_buffer_err = (qm_val >> (port_id * 8)) & 0xFF;
++ } else {
++ reg = AR40XX_REG_QM_PORT4_6_QNUM;
++ ar40xx_write(priv, AR40XX_REG_QM_DEBUG_ADDR, reg);
++ qm_val = ar40xx_read(priv, AR40XX_REG_QM_DEBUG_VALUE);
++ /* every 8 bits for each port */
++ *qm_buffer_err = (qm_val >> ((port_id-4) * 8)) & 0xFF;
++ }
++
++ return 0;
++}
++
++static void
++ar40xx_sw_mac_polling_task(struct ar40xx_priv *priv)
++{
++ static int task_count;
++ u32 i;
++ u32 reg, value;
++ u32 link, speed, duplex;
++ u32 qm_buffer_err;
++ u16 port_phy_status[AR40XX_NUM_PORTS];
++ static u32 qm_err_cnt[AR40XX_NUM_PORTS] = {0, 0, 0, 0, 0, 0};
++ static u32 link_cnt[AR40XX_NUM_PORTS] = {0, 0, 0, 0, 0, 0};
++ struct mii_bus *bus = NULL;
++
++ if (!priv || !priv->mii_bus)
++ return;
++
++ bus = priv->mii_bus;
++
++ ++task_count;
++
++ for (i = 1; i < AR40XX_NUM_PORTS; ++i) {
++ port_phy_status[i] =
++ mdiobus_read(bus, i-1, AR40XX_PHY_SPEC_STATUS);
++ speed = link = duplex = port_phy_status[i];
++ speed &= AR40XX_PHY_SPEC_STATUS_SPEED;
++ speed >>= 14;
++ link &= AR40XX_PHY_SPEC_STATUS_LINK;
++ link >>= 10;
++ duplex &= AR40XX_PHY_SPEC_STATUS_DUPLEX;
++ duplex >>= 13;
++
++ if (link != priv->ar40xx_port_old_link[i]) {
++ ++link_cnt[i];
++ /* Up --> Down */
++ if ((priv->ar40xx_port_old_link[i] ==
++ AR40XX_PORT_LINK_UP) &&
++ (link == AR40XX_PORT_LINK_DOWN)) {
++ /* LINK_EN disable(MAC force mode)*/
++ reg = AR40XX_REG_PORT_STATUS(i);
++ ar40xx_rmw(priv, reg,
++ AR40XX_PORT_AUTO_LINK_EN, 0);
++
++ /* Check queue buffer */
++ qm_err_cnt[i] = 0;
++ ar40xx_get_qm_status(priv, i, &qm_buffer_err);
++ if (qm_buffer_err) {
++ priv->ar40xx_port_qm_buf[i] =
++ AR40XX_QM_NOT_EMPTY;
++ } else {
++ u16 phy_val = 0;
++
++ priv->ar40xx_port_qm_buf[i] =
++ AR40XX_QM_EMPTY;
++ ar40xx_force_1g_full(priv, i);
++ /* Ref:QCA8337 Datasheet,Clearing
++ * MENU_CTRL_EN prevents phy to
++ * stuck in 100BT mode when
++ * bringing up the link
++ */
++ ar40xx_phy_dbg_read(priv, i-1,
++ AR40XX_PHY_DEBUG_0,
++ &phy_val);
++ phy_val &= (~AR40XX_PHY_MANU_CTRL_EN);
++ ar40xx_phy_dbg_write(priv, i-1,
++ AR40XX_PHY_DEBUG_0,
++ phy_val);
++ }
++ priv->ar40xx_port_old_link[i] = link;
++ } else if ((priv->ar40xx_port_old_link[i] ==
++ AR40XX_PORT_LINK_DOWN) &&
++ (link == AR40XX_PORT_LINK_UP)) {
++ /* Down --> Up */
++ if (priv->port_link_up[i] < 1) {
++ ++priv->port_link_up[i];
++ } else {
++ /* Change port status */
++ reg = AR40XX_REG_PORT_STATUS(i);
++ value = ar40xx_read(priv, reg);
++ priv->port_link_up[i] = 0;
++
++ value &= ~(AR40XX_PORT_DUPLEX |
++ AR40XX_PORT_SPEED);
++ value |= speed | (duplex ? BIT(6) : 0);
++ ar40xx_write(priv, reg, value);
++ /* clock switch need such time
++ * to avoid glitch
++ */
++ usleep_range(100, 200);
++
++ value |= AR40XX_PORT_AUTO_LINK_EN;
++ ar40xx_write(priv, reg, value);
++ /* HW need such time to make sure link
++ * stable before enable MAC
++ */
++ usleep_range(100, 200);
++
++ if (speed == AR40XX_PORT_SPEED_100M) {
++ u16 phy_val = 0;
++ /* Enable @100M, if down to 10M
++ * clock will change smoothly
++ */
++ ar40xx_phy_dbg_read(priv, i-1,
++ 0,
++ &phy_val);
++ phy_val |=
++ AR40XX_PHY_MANU_CTRL_EN;
++ ar40xx_phy_dbg_write(priv, i-1,
++ 0,
++ phy_val);
++ }
++ priv->ar40xx_port_old_link[i] = link;
++ }
++ }
++ }
++
++ if (priv->ar40xx_port_qm_buf[i] == AR40XX_QM_NOT_EMPTY) {
++ /* Check QM */
++ ar40xx_get_qm_status(priv, i, &qm_buffer_err);
++ if (qm_buffer_err) {
++ ++qm_err_cnt[i];
++ } else {
++ priv->ar40xx_port_qm_buf[i] =
++ AR40XX_QM_EMPTY;
++ qm_err_cnt[i] = 0;
++ ar40xx_force_1g_full(priv, i);
++ }
++ }
++ }
++}
++
++static void
++ar40xx_qm_err_check_work_task(struct work_struct *work)
++{
++ struct ar40xx_priv *priv = container_of(work, struct ar40xx_priv,
++ qm_dwork.work);
++
++ mutex_lock(&priv->qm_lock);
++
++ ar40xx_sw_mac_polling_task(priv);
++
++ mutex_unlock(&priv->qm_lock);
++
++ schedule_delayed_work(&priv->qm_dwork,
++ msecs_to_jiffies(AR40XX_QM_WORK_DELAY));
++}
++
++static int
++ar40xx_qm_err_check_work_start(struct ar40xx_priv *priv)
++{
++ mutex_init(&priv->qm_lock);
++
++ INIT_DELAYED_WORK(&priv->qm_dwork, ar40xx_qm_err_check_work_task);
++
++ schedule_delayed_work(&priv->qm_dwork,
++ msecs_to_jiffies(AR40XX_QM_WORK_DELAY));
++
++ return 0;
++}
++
++/* End of qm error WAR */
++
++static int
++ar40xx_vlan_init(struct ar40xx_priv *priv)
++{
++ int port;
++ unsigned long bmp;
++
++ /* By default Enable VLAN */
++ priv->vlan = 1;
++ priv->vlan_table[AR40XX_LAN_VLAN] = priv->cpu_bmp | priv->lan_bmp;
++ priv->vlan_table[AR40XX_WAN_VLAN] = priv->cpu_bmp | priv->wan_bmp;
++ priv->vlan_tagged = priv->cpu_bmp;
++ bmp = priv->lan_bmp;
++ for_each_set_bit(port, &bmp, AR40XX_NUM_PORTS)
++ priv->pvid[port] = AR40XX_LAN_VLAN;
++
++ bmp = priv->wan_bmp;
++ for_each_set_bit(port, &bmp, AR40XX_NUM_PORTS)
++ priv->pvid[port] = AR40XX_WAN_VLAN;
++
++ return 0;
++}
++
++static void
++ar40xx_mib_work_func(struct work_struct *work)
++{
++ struct ar40xx_priv *priv;
++ int err;
++
++ priv = container_of(work, struct ar40xx_priv, mib_work.work);
++
++ mutex_lock(&priv->mib_lock);
++
++ err = ar40xx_mib_capture(priv);
++ if (err)
++ goto next_port;
++
++ ar40xx_mib_fetch_port_stat(priv, priv->mib_next_port, false);
++
++next_port:
++ priv->mib_next_port++;
++ if (priv->mib_next_port >= priv->dev.ports)
++ priv->mib_next_port = 0;
++
++ mutex_unlock(&priv->mib_lock);
++
++ schedule_delayed_work(&priv->mib_work,
++ msecs_to_jiffies(AR40XX_MIB_WORK_DELAY));
++}
++
++static void
++ar40xx_setup_port(struct ar40xx_priv *priv, int port, u32 members)
++{
++ u32 t;
++ u32 egress, ingress;
++ u32 pvid = priv->vlan_id[priv->pvid[port]];
++
++ if (priv->vlan) {
++ egress = AR40XX_PORT_VLAN1_OUT_MODE_UNMOD;
++ ingress = AR40XX_IN_SECURE;
++ } else {
++ egress = AR40XX_PORT_VLAN1_OUT_MODE_UNTOUCH;
++ ingress = AR40XX_IN_PORT_ONLY;
++ }
++
++ t = pvid << AR40XX_PORT_VLAN0_DEF_SVID_S;
++ t |= pvid << AR40XX_PORT_VLAN0_DEF_CVID_S;
++ ar40xx_write(priv, AR40XX_REG_PORT_VLAN0(port), t);
++
++ t = AR40XX_PORT_VLAN1_PORT_VLAN_PROP;
++ t |= egress << AR40XX_PORT_VLAN1_OUT_MODE_S;
++ ar40xx_write(priv, AR40XX_REG_PORT_VLAN1(port), t);
++
++ t = members;
++ t |= AR40XX_PORT_LOOKUP_LEARN;
++ t |= ingress << AR40XX_PORT_LOOKUP_IN_MODE_S;
++ t |= AR40XX_PORT_STATE_FORWARD << AR40XX_PORT_LOOKUP_STATE_S;
++ ar40xx_write(priv, AR40XX_REG_PORT_LOOKUP(port), t);
++}
++
++static void
++ar40xx_vtu_op(struct ar40xx_priv *priv, u32 op, u32 val)
++{
++ if (ar40xx_wait_bit(priv, AR40XX_REG_VTU_FUNC1,
++ AR40XX_VTU_FUNC1_BUSY, 0))
++ return;
++
++ if ((op & AR40XX_VTU_FUNC1_OP) == AR40XX_VTU_FUNC1_OP_LOAD)
++ ar40xx_write(priv, AR40XX_REG_VTU_FUNC0, val);
++
++ op |= AR40XX_VTU_FUNC1_BUSY;
++ ar40xx_write(priv, AR40XX_REG_VTU_FUNC1, op);
++}
++
++static void
++ar40xx_vtu_load_vlan(struct ar40xx_priv *priv, u32 vid, u32 port_mask)
++{
++ u32 op;
++ u32 val;
++ int i;
++
++ op = AR40XX_VTU_FUNC1_OP_LOAD | (vid << AR40XX_VTU_FUNC1_VID_S);
++ val = AR40XX_VTU_FUNC0_VALID | AR40XX_VTU_FUNC0_IVL;
++ for (i = 0; i < AR40XX_NUM_PORTS; i++) {
++ u32 mode;
++
++ if ((port_mask & BIT(i)) == 0)
++ mode = AR40XX_VTU_FUNC0_EG_MODE_NOT;
++ else if (priv->vlan == 0)
++ mode = AR40XX_VTU_FUNC0_EG_MODE_KEEP;
++ else if ((priv->vlan_tagged & BIT(i)) ||
++ (priv->vlan_id[priv->pvid[i]] != vid))
++ mode = AR40XX_VTU_FUNC0_EG_MODE_TAG;
++ else
++ mode = AR40XX_VTU_FUNC0_EG_MODE_UNTAG;
++
++ val |= mode << AR40XX_VTU_FUNC0_EG_MODE_S(i);
++ }
++ ar40xx_vtu_op(priv, op, val);
++}
++
++static void
++ar40xx_vtu_flush(struct ar40xx_priv *priv)
++{
++ ar40xx_vtu_op(priv, AR40XX_VTU_FUNC1_OP_FLUSH, 0);
++}
++
++static int
++ar40xx_sw_hw_apply(struct switch_dev *dev)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++ u8 portmask[AR40XX_NUM_PORTS];
++ int i, j;
++
++ mutex_lock(&priv->reg_mutex);
++ /* flush all vlan entries */
++ ar40xx_vtu_flush(priv);
++
++ memset(portmask, 0, sizeof(portmask));
++ if (priv->vlan) {
++ for (j = 0; j < AR40XX_MAX_VLANS; j++) {
++ u8 vp = priv->vlan_table[j];
++
++ if (!vp)
++ continue;
++
++ for (i = 0; i < dev->ports; i++) {
++ u8 mask = BIT(i);
++
++ if (vp & mask)
++ portmask[i] |= vp & ~mask;
++ }
++
++ ar40xx_vtu_load_vlan(priv, priv->vlan_id[j],
++ priv->vlan_table[j]);
++ }
++ } else {
++ /* 8021q vlan disabled */
++ for (i = 0; i < dev->ports; i++) {
++ if (i == AR40XX_PORT_CPU)
++ continue;
++
++ portmask[i] = BIT(AR40XX_PORT_CPU);
++ portmask[AR40XX_PORT_CPU] |= BIT(i);
++ }
++ }
++
++ /* update the port destination mask registers and tag settings */
++ for (i = 0; i < dev->ports; i++)
++ ar40xx_setup_port(priv, i, portmask[i]);
++
++ ar40xx_set_mirror_regs(priv);
++
++ mutex_unlock(&priv->reg_mutex);
++ return 0;
++}
++
++static int
++ar40xx_sw_reset_switch(struct switch_dev *dev)
++{
++ struct ar40xx_priv *priv = swdev_to_ar40xx(dev);
++ int i, rv;
++
++ mutex_lock(&priv->reg_mutex);
++ memset(&priv->vlan, 0, sizeof(struct ar40xx_priv) -
++ offsetof(struct ar40xx_priv, vlan));
++
++ for (i = 0; i < AR40XX_MAX_VLANS; i++)
++ priv->vlan_id[i] = i;
++
++ ar40xx_vlan_init(priv);
++
++ priv->mirror_rx = false;
++ priv->mirror_tx = false;
++ priv->source_port = 0;
++ priv->monitor_port = 0;
++
++ mutex_unlock(&priv->reg_mutex);
++
++ rv = ar40xx_sw_hw_apply(dev);
++ return rv;
++}
++
++static int
++ar40xx_start(struct ar40xx_priv *priv)
++{
++ int ret;
++
++ ret = ar40xx_hw_init(priv);
++ if (ret)
++ return ret;
++
++ ret = ar40xx_sw_reset_switch(&priv->dev);
++ if (ret)
++ return ret;
++
++ /* at last, setup cpu port */
++ ret = ar40xx_cpuport_setup(priv);
++ if (ret)
++ return ret;
++
++ schedule_delayed_work(&priv->mib_work,
++ msecs_to_jiffies(AR40XX_MIB_WORK_DELAY));
++
++ ar40xx_qm_err_check_work_start(priv);
++
++ return 0;
++}
++
++static const struct switch_dev_ops ar40xx_sw_ops = {
++ .attr_global = {
++ .attr = ar40xx_sw_attr_globals,
++ .n_attr = ARRAY_SIZE(ar40xx_sw_attr_globals),
++ },
++ .attr_port = {
++ .attr = ar40xx_sw_attr_port,
++ .n_attr = ARRAY_SIZE(ar40xx_sw_attr_port),
++ },
++ .attr_vlan = {
++ .attr = ar40xx_sw_attr_vlan,
++ .n_attr = ARRAY_SIZE(ar40xx_sw_attr_vlan),
++ },
++ .get_port_pvid = ar40xx_sw_get_pvid,
++ .set_port_pvid = ar40xx_sw_set_pvid,
++ .get_vlan_ports = ar40xx_sw_get_ports,
++ .set_vlan_ports = ar40xx_sw_set_ports,
++ .apply_config = ar40xx_sw_hw_apply,
++ .reset_switch = ar40xx_sw_reset_switch,
++ .get_port_link = ar40xx_sw_get_port_link,
++};
++
++/* Start of phy driver support */
++
++static const u32 ar40xx_phy_ids[] = {
++ 0x004dd0b1,
++ 0x004dd0b2, /* AR40xx */
++};
++
++static bool
++ar40xx_phy_match(u32 phy_id)
++{
++ int i;
++
++ for (i = 0; i < ARRAY_SIZE(ar40xx_phy_ids); i++)
++ if (phy_id == ar40xx_phy_ids[i])
++ return true;
++
++ return false;
++}
++
++static bool
++is_ar40xx_phy(struct mii_bus *bus)
++{
++ unsigned i;
++
++ for (i = 0; i < 4; i++) {
++ u32 phy_id;
++
++ phy_id = mdiobus_read(bus, i, MII_PHYSID1) << 16;
++ phy_id |= mdiobus_read(bus, i, MII_PHYSID2);
++ if (!ar40xx_phy_match(phy_id))
++ return false;
++ }
++
++ return true;
++}
++
++static int
++ar40xx_phy_probe(struct phy_device *phydev)
++{
++ if (!is_ar40xx_phy(phydev->mdio.bus))
++ return -ENODEV;
++
++ ar40xx_priv->mii_bus = phydev->mdio.bus;
++ phydev->priv = ar40xx_priv;
++ if (phydev->mdio.addr == 0)
++ ar40xx_priv->phy = phydev;
++
++ phydev->supported |= SUPPORTED_1000baseT_Full;
++ phydev->advertising |= ADVERTISED_1000baseT_Full;
++ return 0;
++}
++
++static void
++ar40xx_phy_remove(struct phy_device *phydev)
++{
++ ar40xx_priv->mii_bus = NULL;
++ phydev->priv = NULL;
++}
++
++static int
++ar40xx_phy_config_init(struct phy_device *phydev)
++{
++ return 0;
++}
++
++static int
++ar40xx_phy_read_status(struct phy_device *phydev)
++{
++ if (phydev->mdio.addr != 0)
++ return genphy_read_status(phydev);
++
++ return 0;
++}
++
++static int
++ar40xx_phy_config_aneg(struct phy_device *phydev)
++{
++ if (phydev->mdio.addr == 0)
++ return 0;
++
++ return genphy_config_aneg(phydev);
++}
++
++static struct phy_driver ar40xx_phy_driver = {
++ .phy_id = 0x004d0000,
++ .name = "QCA Malibu",
++ .phy_id_mask = 0xffff0000,
++ .features = PHY_BASIC_FEATURES,
++ .probe = ar40xx_phy_probe,
++ .remove = ar40xx_phy_remove,
++ .config_init = ar40xx_phy_config_init,
++ .config_aneg = ar40xx_phy_config_aneg,
++ .read_status = ar40xx_phy_read_status,
++};
++
++static uint16_t ar40xx_gpio_get_phy(unsigned int offset)
++{
++ return offset / 4;
++}
++
++static uint16_t ar40xx_gpio_get_reg(unsigned int offset)
++{
++ return 0x8074 + offset % 4;
++}
++
++static void ar40xx_gpio_set(struct gpio_chip *gc, unsigned int offset,
++ int value)
++{
++ struct ar40xx_priv *priv = gpiochip_get_data(gc);
++
++ ar40xx_phy_mmd_write(priv, ar40xx_gpio_get_phy(offset), 0x7,
++ ar40xx_gpio_get_reg(offset),
++ value ? 0xA000 : 0x8000);
++}
++
++static int ar40xx_gpio_get(struct gpio_chip *gc, unsigned offset)
++{
++ struct ar40xx_priv *priv = gpiochip_get_data(gc);
++
++ return ar40xx_phy_mmd_read(priv, ar40xx_gpio_get_phy(offset), 0x7,
++ ar40xx_gpio_get_reg(offset)) == 0xA000;
++}
++
++static int ar40xx_gpio_get_dir(struct gpio_chip *gc, unsigned offset)
++{
++ return 0; /* only out direction */
++}
++
++static int ar40xx_gpio_dir_out(struct gpio_chip *gc, unsigned offset,
++ int value)
++{
++ /*
++ * the direction out value is used to set the initial value.
++ * support of this function is required by leds-gpio.c
++ */
++ ar40xx_gpio_set(gc, offset, value);
++ return 0;
++}
++
++static void ar40xx_register_gpio(struct device *pdev,
++ struct ar40xx_priv *priv,
++ struct device_node *switch_node)
++{
++ struct gpio_chip *gc;
++ int err;
++
++ gc = devm_kzalloc(pdev, sizeof(*gc), GFP_KERNEL);
++ if (!gc)
++ return;
++
++ gc->label = "ar40xx_gpio",
++ gc->base = -1,
++ gc->ngpio = 5 /* mmd 0 - 4 */ * 4 /* 0x8074 - 0x8077 */,
++ gc->parent = pdev;
++ gc->owner = THIS_MODULE;
++
++ gc->get_direction = ar40xx_gpio_get_dir;
++ gc->direction_output = ar40xx_gpio_dir_out;
++ gc->get = ar40xx_gpio_get;
++ gc->set = ar40xx_gpio_set;
++ gc->can_sleep = true;
++ gc->label = priv->dev.name;
++ gc->of_node = switch_node;
++
++ err = devm_gpiochip_add_data(pdev, gc, priv);
++ if (err != 0)
++ dev_err(pdev, "Failed to register gpio %d.\n", err);
++}
++
++/* End of phy driver support */
++
++/* Platform driver probe function */
++
++static int ar40xx_probe(struct platform_device *pdev)
++{
++ struct device_node *switch_node;
++ struct device_node *psgmii_node;
++ const __be32 *mac_mode;
++ struct clk *ess_clk;
++ struct switch_dev *swdev;
++ struct ar40xx_priv *priv;
++ u32 len;
++ u32 num_mibs;
++ struct resource psgmii_base = {0};
++ struct resource switch_base = {0};
++ int ret;
++
++ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
++ if (!priv)
++ return -ENOMEM;
++
++ platform_set_drvdata(pdev, priv);
++ ar40xx_priv = priv;
++
++ switch_node = of_node_get(pdev->dev.of_node);
++ if (of_address_to_resource(switch_node, 0, &switch_base) != 0)
++ return -EIO;
++
++ priv->hw_addr = devm_ioremap_resource(&pdev->dev, &switch_base);
++ if (IS_ERR(priv->hw_addr)) {
++ dev_err(&pdev->dev, "Failed to ioremap switch_base!\n");
++ return PTR_ERR(priv->hw_addr);
++ }
++
++ /*psgmii dts get*/
++ psgmii_node = of_find_node_by_name(NULL, "ess-psgmii");
++ if (!psgmii_node) {
++ dev_err(&pdev->dev, "Failed to find ess-psgmii node!\n");
++ return -EINVAL;
++ }
++
++ if (of_address_to_resource(psgmii_node, 0, &psgmii_base) != 0)
++ return -EIO;
++
++ priv->psgmii_hw_addr = devm_ioremap_resource(&pdev->dev, &psgmii_base);
++ if (IS_ERR(priv->psgmii_hw_addr)) {
++ dev_err(&pdev->dev, "psgmii ioremap fail!\n");
++ return PTR_ERR(priv->psgmii_hw_addr);
++ }
++
++ mac_mode = of_get_property(switch_node, "switch_mac_mode", &len);
++ if (!mac_mode) {
++ dev_err(&pdev->dev, "Failed to read switch_mac_mode\n");
++ return -EINVAL;
++ }
++ priv->mac_mode = be32_to_cpup(mac_mode);
++
++ ess_clk = of_clk_get_by_name(switch_node, "ess_clk");
++ if (ess_clk)
++ clk_prepare_enable(ess_clk);
++
++ priv->ess_rst = devm_reset_control_get(&pdev->dev, "ess_rst");
++ if (IS_ERR(priv->ess_rst)) {
++ dev_err(&pdev->dev, "Failed to get ess_rst control!\n");
++ return PTR_ERR(priv->ess_rst);
++ }
++
++ if (of_property_read_u32(switch_node, "switch_cpu_bmp",
++ &priv->cpu_bmp) ||
++ of_property_read_u32(switch_node, "switch_lan_bmp",
++ &priv->lan_bmp) ||
++ of_property_read_u32(switch_node, "switch_wan_bmp",
++ &priv->wan_bmp)) {
++ dev_err(&pdev->dev, "Failed to read port properties\n");
++ return -EIO;
++ }
++
++ ret = phy_driver_register(&ar40xx_phy_driver, THIS_MODULE);
++ if (ret) {
++ dev_err(&pdev->dev, "Failed to register ar40xx phy driver!\n");
++ return -EIO;
++ }
++
++ mutex_init(&priv->reg_mutex);
++ mutex_init(&priv->mib_lock);
++ INIT_DELAYED_WORK(&priv->mib_work, ar40xx_mib_work_func);
++
++ /* register switch */
++ swdev = &priv->dev;
++
++ swdev->alias = dev_name(&priv->mii_bus->dev);
++
++ swdev->cpu_port = AR40XX_PORT_CPU;
++ swdev->name = "QCA AR40xx";
++ swdev->vlans = AR40XX_MAX_VLANS;
++ swdev->ports = AR40XX_NUM_PORTS;
++ swdev->ops = &ar40xx_sw_ops;
++ ret = register_switch(swdev, NULL);
++ if (ret)
++ goto err_unregister_phy;
++
++ num_mibs = ARRAY_SIZE(ar40xx_mibs);
++ len = priv->dev.ports * num_mibs *
++ sizeof(*priv->mib_stats);
++ priv->mib_stats = devm_kzalloc(&pdev->dev, len, GFP_KERNEL);
++ if (!priv->mib_stats) {
++ ret = -ENOMEM;
++ goto err_unregister_switch;
++ }
++
++ ar40xx_start(priv);
++
++ if (of_property_read_bool(switch_node, "gpio-controller"))
++ ar40xx_register_gpio(&pdev->dev, ar40xx_priv, switch_node);
++
++ return 0;
++
++err_unregister_switch:
++ unregister_switch(&priv->dev);
++err_unregister_phy:
++ phy_driver_unregister(&ar40xx_phy_driver);
++ platform_set_drvdata(pdev, NULL);
++ return ret;
++}
++
++static int ar40xx_remove(struct platform_device *pdev)
++{
++ struct ar40xx_priv *priv = platform_get_drvdata(pdev);
++
++ cancel_delayed_work_sync(&priv->qm_dwork);
++ cancel_delayed_work_sync(&priv->mib_work);
++
++ unregister_switch(&priv->dev);
++
++ phy_driver_unregister(&ar40xx_phy_driver);
++
++ return 0;
++}
++
++static const struct of_device_id ar40xx_of_mtable[] = {
++ {.compatible = "qcom,ess-switch" },
++ {}
++};
++
++struct platform_driver ar40xx_drv = {
++ .probe = ar40xx_probe,
++ .remove = ar40xx_remove,
++ .driver = {
++ .name = "ar40xx",
++ .of_match_table = ar40xx_of_mtable,
++ },
++};
++
++module_platform_driver(ar40xx_drv);
++
++MODULE_DESCRIPTION("IPQ40XX ESS driver");
++MODULE_LICENSE("Dual BSD/GPL");
+--- /dev/null
++++ b/drivers/net/phy/ar40xx.h
+@@ -0,0 +1,337 @@
++/*
++ * Copyright (c) 2016, The Linux Foundation. All rights reserved.
++ *
++ * Permission to use, copy, modify, and/or distribute this software for
++ * any purpose with or without fee is hereby granted, provided that the
++ * above copyright notice and this permission notice appear in all copies.
++ * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
++ * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
++ * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
++ * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
++ * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
++ * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT
++ * OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
++ */
++
++ #ifndef __AR40XX_H
++#define __AR40XX_H
++
++#define AR40XX_MAX_VLANS 128
++#define AR40XX_NUM_PORTS 6
++#define AR40XX_NUM_PHYS 5
++
++#define BITS(_s, _n) (((1UL << (_n)) - 1) << _s)
++
++struct ar40xx_priv {
++ struct switch_dev dev;
++
++ u8 __iomem *hw_addr;
++ u8 __iomem *psgmii_hw_addr;
++ u32 mac_mode;
++ struct reset_control *ess_rst;
++ u32 cpu_bmp;
++ u32 lan_bmp;
++ u32 wan_bmp;
++
++ struct mii_bus *mii_bus;
++ struct phy_device *phy;
++
++ /* mutex for qm task */
++ struct mutex qm_lock;
++ struct delayed_work qm_dwork;
++ u32 port_link_up[AR40XX_NUM_PORTS];
++ u32 ar40xx_port_old_link[AR40XX_NUM_PORTS];
++ u32 ar40xx_port_qm_buf[AR40XX_NUM_PORTS];
++
++ u32 phy_t_status;
++
++ /* mutex for switch reg access */
++ struct mutex reg_mutex;
++
++ /* mutex for mib task */
++ struct mutex mib_lock;
++ struct delayed_work mib_work;
++ int mib_next_port;
++ u64 *mib_stats;
++
++ char buf[2048];
++
++ /* all fields below will be cleared on reset */
++ bool vlan;
++ u16 vlan_id[AR40XX_MAX_VLANS];
++ u8 vlan_table[AR40XX_MAX_VLANS];
++ u8 vlan_tagged;
++ u16 pvid[AR40XX_NUM_PORTS];
++
++ /* mirror */
++ bool mirror_rx;
++ bool mirror_tx;
++ int source_port;
++ int monitor_port;
++};
++
++#define AR40XX_PORT_LINK_UP 1
++#define AR40XX_PORT_LINK_DOWN 0
++#define AR40XX_QM_NOT_EMPTY 1
++#define AR40XX_QM_EMPTY 0
++
++#define AR40XX_LAN_VLAN 1
++#define AR40XX_WAN_VLAN 2
++
++enum ar40xx_port_wrapper_cfg {
++ PORT_WRAPPER_PSGMII = 0,
++};
++
++struct ar40xx_mib_desc {
++ u32 size;
++ u32 offset;
++ const char *name;
++};
++
++#define AR40XX_PORT_CPU 0
++
++#define AR40XX_PSGMII_MODE_CONTROL 0x1b4
++#define AR40XX_PSGMII_ATHR_CSCO_MODE_25M BIT(0)
++
++#define AR40XX_PSGMIIPHY_TX_CONTROL 0x288
++
++#define AR40XX_MII_ATH_MMD_ADDR 0x0d
++#define AR40XX_MII_ATH_MMD_DATA 0x0e
++#define AR40XX_MII_ATH_DBG_ADDR 0x1d
++#define AR40XX_MII_ATH_DBG_DATA 0x1e
++
++#define AR40XX_STATS_RXBROAD 0x00
++#define AR40XX_STATS_RXPAUSE 0x04
++#define AR40XX_STATS_RXMULTI 0x08
++#define AR40XX_STATS_RXFCSERR 0x0c
++#define AR40XX_STATS_RXALIGNERR 0x10
++#define AR40XX_STATS_RXRUNT 0x14
++#define AR40XX_STATS_RXFRAGMENT 0x18
++#define AR40XX_STATS_RX64BYTE 0x1c
++#define AR40XX_STATS_RX128BYTE 0x20
++#define AR40XX_STATS_RX256BYTE 0x24
++#define AR40XX_STATS_RX512BYTE 0x28
++#define AR40XX_STATS_RX1024BYTE 0x2c
++#define AR40XX_STATS_RX1518BYTE 0x30
++#define AR40XX_STATS_RXMAXBYTE 0x34
++#define AR40XX_STATS_RXTOOLONG 0x38
++#define AR40XX_STATS_RXGOODBYTE 0x3c
++#define AR40XX_STATS_RXBADBYTE 0x44
++#define AR40XX_STATS_RXOVERFLOW 0x4c
++#define AR40XX_STATS_FILTERED 0x50
++#define AR40XX_STATS_TXBROAD 0x54
++#define AR40XX_STATS_TXPAUSE 0x58
++#define AR40XX_STATS_TXMULTI 0x5c
++#define AR40XX_STATS_TXUNDERRUN 0x60
++#define AR40XX_STATS_TX64BYTE 0x64
++#define AR40XX_STATS_TX128BYTE 0x68
++#define AR40XX_STATS_TX256BYTE 0x6c
++#define AR40XX_STATS_TX512BYTE 0x70
++#define AR40XX_STATS_TX1024BYTE 0x74
++#define AR40XX_STATS_TX1518BYTE 0x78
++#define AR40XX_STATS_TXMAXBYTE 0x7c
++#define AR40XX_STATS_TXOVERSIZE 0x80
++#define AR40XX_STATS_TXBYTE 0x84
++#define AR40XX_STATS_TXCOLLISION 0x8c
++#define AR40XX_STATS_TXABORTCOL 0x90
++#define AR40XX_STATS_TXMULTICOL 0x94
++#define AR40XX_STATS_TXSINGLECOL 0x98
++#define AR40XX_STATS_TXEXCDEFER 0x9c
++#define AR40XX_STATS_TXDEFER 0xa0
++#define AR40XX_STATS_TXLATECOL 0xa4
++
++#define AR40XX_REG_MODULE_EN 0x030
++#define AR40XX_MODULE_EN_MIB BIT(0)
++
++#define AR40XX_REG_MIB_FUNC 0x034
++#define AR40XX_MIB_BUSY BIT(17)
++#define AR40XX_MIB_CPU_KEEP BIT(20)
++#define AR40XX_MIB_FUNC BITS(24, 3)
++#define AR40XX_MIB_FUNC_S 24
++#define AR40XX_MIB_FUNC_NO_OP 0x0
++#define AR40XX_MIB_FUNC_FLUSH 0x1
++
++#define AR40XX_REG_PORT_STATUS(_i) (0x07c + (_i) * 4)
++#define AR40XX_PORT_SPEED BITS(0, 2)
++#define AR40XX_PORT_STATUS_SPEED_S 0
++#define AR40XX_PORT_TX_EN BIT(2)
++#define AR40XX_PORT_RX_EN BIT(3)
++#define AR40XX_PORT_STATUS_TXFLOW BIT(4)
++#define AR40XX_PORT_STATUS_RXFLOW BIT(5)
++#define AR40XX_PORT_DUPLEX BIT(6)
++#define AR40XX_PORT_TXHALF_FLOW BIT(7)
++#define AR40XX_PORT_STATUS_LINK_UP BIT(8)
++#define AR40XX_PORT_AUTO_LINK_EN BIT(9)
++#define AR40XX_PORT_STATUS_FLOW_CONTROL BIT(12)
++
++#define AR40XX_REG_MAX_FRAME_SIZE 0x078
++#define AR40XX_MAX_FRAME_SIZE_MTU BITS(0, 14)
++
++#define AR40XX_REG_PORT_HEADER(_i) (0x09c + (_i) * 4)
++
++#define AR40XX_REG_EEE_CTRL 0x100
++#define AR40XX_EEE_CTRL_DISABLE_PHY(_i) BIT(4 + (_i) * 2)
++
++#define AR40XX_REG_PORT_VLAN0(_i) (0x420 + (_i) * 0x8)
++#define AR40XX_PORT_VLAN0_DEF_SVID BITS(0, 12)
++#define AR40XX_PORT_VLAN0_DEF_SVID_S 0
++#define AR40XX_PORT_VLAN0_DEF_CVID BITS(16, 12)
++#define AR40XX_PORT_VLAN0_DEF_CVID_S 16
++
++#define AR40XX_REG_PORT_VLAN1(_i) (0x424 + (_i) * 0x8)
++#define AR40XX_PORT_VLAN1_PORT_VLAN_PROP BIT(6)
++#define AR40XX_PORT_VLAN1_OUT_MODE BITS(12, 2)
++#define AR40XX_PORT_VLAN1_OUT_MODE_S 12
++#define AR40XX_PORT_VLAN1_OUT_MODE_UNMOD 0
++#define AR40XX_PORT_VLAN1_OUT_MODE_UNTAG 1
++#define AR40XX_PORT_VLAN1_OUT_MODE_TAG 2
++#define AR40XX_PORT_VLAN1_OUT_MODE_UNTOUCH 3
++
++#define AR40XX_REG_VTU_FUNC0 0x0610
++#define AR40XX_VTU_FUNC0_EG_MODE BITS(4, 14)
++#define AR40XX_VTU_FUNC0_EG_MODE_S(_i) (4 + (_i) * 2)
++#define AR40XX_VTU_FUNC0_EG_MODE_KEEP 0
++#define AR40XX_VTU_FUNC0_EG_MODE_UNTAG 1
++#define AR40XX_VTU_FUNC0_EG_MODE_TAG 2
++#define AR40XX_VTU_FUNC0_EG_MODE_NOT 3
++#define AR40XX_VTU_FUNC0_IVL BIT(19)
++#define AR40XX_VTU_FUNC0_VALID BIT(20)
++
++#define AR40XX_REG_VTU_FUNC1 0x0614
++#define AR40XX_VTU_FUNC1_OP BITS(0, 3)
++#define AR40XX_VTU_FUNC1_OP_NOOP 0
++#define AR40XX_VTU_FUNC1_OP_FLUSH 1
++#define AR40XX_VTU_FUNC1_OP_LOAD 2
++#define AR40XX_VTU_FUNC1_OP_PURGE 3
++#define AR40XX_VTU_FUNC1_OP_REMOVE_PORT 4
++#define AR40XX_VTU_FUNC1_OP_GET_NEXT 5
++#define AR40XX7_VTU_FUNC1_OP_GET_ONE 6
++#define AR40XX_VTU_FUNC1_FULL BIT(4)
++#define AR40XX_VTU_FUNC1_PORT BIT(8, 4)
++#define AR40XX_VTU_FUNC1_PORT_S 8
++#define AR40XX_VTU_FUNC1_VID BIT(16, 12)
++#define AR40XX_VTU_FUNC1_VID_S 16
++#define AR40XX_VTU_FUNC1_BUSY BIT(31)
++
++#define AR40XX_REG_FWD_CTRL0 0x620
++#define AR40XX_FWD_CTRL0_CPU_PORT_EN BIT(10)
++#define AR40XX_FWD_CTRL0_MIRROR_PORT BITS(4, 4)
++#define AR40XX_FWD_CTRL0_MIRROR_PORT_S 4
++
++#define AR40XX_REG_FWD_CTRL1 0x624
++#define AR40XX_FWD_CTRL1_UC_FLOOD BITS(0, 7)
++#define AR40XX_FWD_CTRL1_UC_FLOOD_S 0
++#define AR40XX_FWD_CTRL1_MC_FLOOD BITS(8, 7)
++#define AR40XX_FWD_CTRL1_MC_FLOOD_S 8
++#define AR40XX_FWD_CTRL1_BC_FLOOD BITS(16, 7)
++#define AR40XX_FWD_CTRL1_BC_FLOOD_S 16
++#define AR40XX_FWD_CTRL1_IGMP BITS(24, 7)
++#define AR40XX_FWD_CTRL1_IGMP_S 24
++
++#define AR40XX_REG_PORT_LOOKUP(_i) (0x660 + (_i) * 0xc)
++#define AR40XX_PORT_LOOKUP_MEMBER BITS(0, 7)
++#define AR40XX_PORT_LOOKUP_IN_MODE BITS(8, 2)
++#define AR40XX_PORT_LOOKUP_IN_MODE_S 8
++#define AR40XX_PORT_LOOKUP_STATE BITS(16, 3)
++#define AR40XX_PORT_LOOKUP_STATE_S 16
++#define AR40XX_PORT_LOOKUP_LEARN BIT(20)
++#define AR40XX_PORT_LOOKUP_LOOPBACK BIT(21)
++#define AR40XX_PORT_LOOKUP_ING_MIRROR_EN BIT(25)
++
++#define AR40XX_REG_ATU_FUNC 0x60c
++#define AR40XX_ATU_FUNC_OP BITS(0, 4)
++#define AR40XX_ATU_FUNC_OP_NOOP 0x0
++#define AR40XX_ATU_FUNC_OP_FLUSH 0x1
++#define AR40XX_ATU_FUNC_OP_LOAD 0x2
++#define AR40XX_ATU_FUNC_OP_PURGE 0x3
++#define AR40XX_ATU_FUNC_OP_FLUSH_LOCKED 0x4
++#define AR40XX_ATU_FUNC_OP_FLUSH_UNICAST 0x5
++#define AR40XX_ATU_FUNC_OP_GET_NEXT 0x6
++#define AR40XX_ATU_FUNC_OP_SEARCH_MAC 0x7
++#define AR40XX_ATU_FUNC_OP_CHANGE_TRUNK 0x8
++#define AR40XX_ATU_FUNC_BUSY BIT(31)
++
++#define AR40XX_REG_QM_DEBUG_ADDR 0x820
++#define AR40XX_REG_QM_DEBUG_VALUE 0x824
++#define AR40XX_REG_QM_PORT0_3_QNUM 0x1d
++#define AR40XX_REG_QM_PORT4_6_QNUM 0x1e
++
++#define AR40XX_REG_PORT_HOL_CTRL1(_i) (0x974 + (_i) * 0x8)
++#define AR40XX_PORT_HOL_CTRL1_EG_MIRROR_EN BIT(16)
++
++#define AR40XX_REG_PORT_FLOWCTRL_THRESH(_i) (0x9b0 + (_i) * 0x4)
++#define AR40XX_PORT0_FC_THRESH_ON_DFLT 0x60
++#define AR40XX_PORT0_FC_THRESH_OFF_DFLT 0x90
++
++#define AR40XX_PHY_DEBUG_0 0
++#define AR40XX_PHY_MANU_CTRL_EN BIT(12)
++
++#define AR40XX_PHY_DEBUG_2 2
++
++#define AR40XX_PHY_SPEC_STATUS 0x11
++#define AR40XX_PHY_SPEC_STATUS_LINK BIT(10)
++#define AR40XX_PHY_SPEC_STATUS_DUPLEX BIT(13)
++#define AR40XX_PHY_SPEC_STATUS_SPEED BITS(14, 2)
++
++/* port forwarding state */
++enum {
++ AR40XX_PORT_STATE_DISABLED = 0,
++ AR40XX_PORT_STATE_BLOCK = 1,
++ AR40XX_PORT_STATE_LISTEN = 2,
++ AR40XX_PORT_STATE_LEARN = 3,
++ AR40XX_PORT_STATE_FORWARD = 4
++};
++
++/* ingress 802.1q mode */
++enum {
++ AR40XX_IN_PORT_ONLY = 0,
++ AR40XX_IN_PORT_FALLBACK = 1,
++ AR40XX_IN_VLAN_ONLY = 2,
++ AR40XX_IN_SECURE = 3
++};
++
++/* egress 802.1q mode */
++enum {
++ AR40XX_OUT_KEEP = 0,
++ AR40XX_OUT_STRIP_VLAN = 1,
++ AR40XX_OUT_ADD_VLAN = 2
++};
++
++/* port speed */
++enum {
++ AR40XX_PORT_SPEED_10M = 0,
++ AR40XX_PORT_SPEED_100M = 1,
++ AR40XX_PORT_SPEED_1000M = 2,
++ AR40XX_PORT_SPEED_ERR = 3,
++};
++
++#define AR40XX_MIB_WORK_DELAY 2000 /* msecs */
++
++#define AR40XX_QM_WORK_DELAY 100
++
++#define AR40XX_MIB_FUNC_CAPTURE 0x3
++
++#define AR40XX_REG_PORT_STATS_START 0x1000
++#define AR40XX_REG_PORT_STATS_LEN 0x100
++
++#define AR40XX_PORTS_ALL 0x3f
++
++#define AR40XX_PSGMII_ID 5
++#define AR40XX_PSGMII_CALB_NUM 100
++#define AR40XX_MALIBU_PSGMII_MODE_CTRL 0x6d
++#define AR40XX_MALIBU_PHY_PSGMII_MODE_CTRL_ADJUST_VAL 0x220c
++#define AR40XX_MALIBU_PHY_MMD7_DAC_CTRL 0x801a
++#define AR40XX_MALIBU_DAC_CTRL_MASK 0x380
++#define AR40XX_MALIBU_DAC_CTRL_VALUE 0x280
++#define AR40XX_MALIBU_PHY_RLP_CTRL 0x805a
++#define AR40XX_PSGMII_TX_DRIVER_1_CTRL 0xb
++#define AR40XX_MALIBU_PHY_PSGMII_REDUCE_SERDES_TX_AMP 0x8a
++#define AR40XX_MALIBU_PHY_LAST_ADDR 4
++
++static inline struct ar40xx_priv *
++swdev_to_ar40xx(struct switch_dev *swdev)
++{
++ return container_of(swdev, struct ar40xx_priv, dev);
++}
++
++#endif
--- /dev/null
+Index: linux-5.4.11/drivers/net/phy/ar40xx.c
+===================================================================
+--- linux-5.4.11.orig/drivers/net/phy/ar40xx.c
++++ linux-5.4.11/drivers/net/phy/ar40xx.c
+@@ -1808,8 +1808,8 @@ ar40xx_phy_probe(struct phy_device *phyd
+ if (phydev->mdio.addr == 0)
+ ar40xx_priv->phy = phydev;
+
+- phydev->supported |= SUPPORTED_1000baseT_Full;
+- phydev->advertising |= ADVERTISED_1000baseT_Full;
++ phy_set_max_speed(phydev, SPEED_1000);
++ linkmode_copy(phydev->advertising, phydev->supported);
+ return 0;
+ }
+
+@@ -2021,6 +2021,12 @@ static int ar40xx_probe(struct platform_
+ /* register switch */
+ swdev = &priv->dev;
+
++ if (priv->mii_bus == NULL) {
++ dev_err(&pdev->dev, "Probe failed - Missing PHYs!\n");
++ ret = -ENODEV;
++ goto err_missing_phy;
++ }
++
+ swdev->alias = dev_name(&priv->mii_bus->dev);
+
+ swdev->cpu_port = AR40XX_PORT_CPU;
+@@ -2052,6 +2058,7 @@ err_unregister_switch:
+ unregister_switch(&priv->dev);
+ err_unregister_phy:
+ phy_driver_unregister(&ar40xx_phy_driver);
++err_missing_phy:
+ platform_set_drvdata(pdev, NULL);
+ return ret;
+ }
--- /dev/null
+From 12e9319da1adacac92930c899c99f0e1970cac11 Mon Sep 17 00:00:00 2001
+From: Christian Lamparter <chunkeey@googlemail.com>
+Date: Thu, 19 Jan 2017 02:01:31 +0100
+Subject: [PATCH 33/38] NET: add qualcomm essedma ethernet driver
+
+Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
+---
+ drivers/net/ethernet/qualcomm/Kconfig | 9 +++++++++
+ drivers/net/ethernet/qualcomm/Makefile | 1 +
+ 2 files changed, 10 insertions(+)
+
+Index: linux-5.4.11/drivers/net/ethernet/qualcomm/Kconfig
+===================================================================
+--- linux-5.4.11.orig/drivers/net/ethernet/qualcomm/Kconfig
++++ linux-5.4.11/drivers/net/ethernet/qualcomm/Kconfig
+@@ -62,4 +62,13 @@ config QCOM_EMAC
+
+ source "drivers/net/ethernet/qualcomm/rmnet/Kconfig"
+
++config ESSEDMA
++ tristate "Qualcomm Atheros ESS Edma support"
++ ---help---
++ This driver supports ethernet edma adapter.
++ Say Y to build this driver.
++
++ To compile this driver as a module, choose M here. The module
++ will be called essedma.ko.
++
+ endif # NET_VENDOR_QUALCOMM
+Index: linux-5.4.11/drivers/net/ethernet/qualcomm/Makefile
+===================================================================
+--- linux-5.4.11.orig/drivers/net/ethernet/qualcomm/Makefile
++++ linux-5.4.11/drivers/net/ethernet/qualcomm/Makefile
+@@ -10,5 +10,6 @@ obj-$(CONFIG_QCA7000_UART) += qcauart.o
+ qcauart-objs := qca_uart.o
+
+ obj-y += emac/
++obj-$(CONFIG_ESSEDMA) += essedma/
+
+ obj-$(CONFIG_RMNET) += rmnet/
--- /dev/null
+From c611d3780fa101662a822d10acf8feb04ca97409 Mon Sep 17 00:00:00 2001
+From: Christian Lamparter <chunkeey@gmail.com>
+Date: Sun, 20 Nov 2016 01:01:10 +0100
+Subject: [PATCH] dts: ipq4019: add ethernet essedma node
+
+This patch adds the device-tree node for the ethernet
+interfaces.
+
+Note: The driver isn't anywhere close to be upstream,
+so the info might change.
+
+Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
+---
+ arch/arm/boot/dts/qcom-ipq4019.dtsi | 60 +++++++++++++++++++++++++++++++++++++
+ 1 file changed, 60 insertions(+)
+
+--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
+@@ -44,6 +44,8 @@
+ spi1 = &blsp1_spi2;
+ i2c0 = &blsp1_i2c3;
+ i2c1 = &blsp1_i2c4;
++ ethernet0 = &gmac0;
++ ethernet1 = &gmac1;
+ };
+
+ cpus {
+@@ -622,6 +624,64 @@
+ status = "disabled";
+ };
+
++ edma@c080000 {
++ compatible = "qcom,ess-edma";
++ reg = <0xc080000 0x8000>;
++ qcom,page-mode = <0>;
++ qcom,rx_head_buf_size = <1540>;
++ qcom,mdio_supported;
++ qcom,poll_required = <1>;
++ qcom,num_gmac = <2>;
++ interrupts = <0 65 IRQ_TYPE_EDGE_RISING
++ 0 66 IRQ_TYPE_EDGE_RISING
++ 0 67 IRQ_TYPE_EDGE_RISING
++ 0 68 IRQ_TYPE_EDGE_RISING
++ 0 69 IRQ_TYPE_EDGE_RISING
++ 0 70 IRQ_TYPE_EDGE_RISING
++ 0 71 IRQ_TYPE_EDGE_RISING
++ 0 72 IRQ_TYPE_EDGE_RISING
++ 0 73 IRQ_TYPE_EDGE_RISING
++ 0 74 IRQ_TYPE_EDGE_RISING
++ 0 75 IRQ_TYPE_EDGE_RISING
++ 0 76 IRQ_TYPE_EDGE_RISING
++ 0 77 IRQ_TYPE_EDGE_RISING
++ 0 78 IRQ_TYPE_EDGE_RISING
++ 0 79 IRQ_TYPE_EDGE_RISING
++ 0 80 IRQ_TYPE_EDGE_RISING
++ 0 240 IRQ_TYPE_EDGE_RISING
++ 0 241 IRQ_TYPE_EDGE_RISING
++ 0 242 IRQ_TYPE_EDGE_RISING
++ 0 243 IRQ_TYPE_EDGE_RISING
++ 0 244 IRQ_TYPE_EDGE_RISING
++ 0 245 IRQ_TYPE_EDGE_RISING
++ 0 246 IRQ_TYPE_EDGE_RISING
++ 0 247 IRQ_TYPE_EDGE_RISING
++ 0 248 IRQ_TYPE_EDGE_RISING
++ 0 249 IRQ_TYPE_EDGE_RISING
++ 0 250 IRQ_TYPE_EDGE_RISING
++ 0 251 IRQ_TYPE_EDGE_RISING
++ 0 252 IRQ_TYPE_EDGE_RISING
++ 0 253 IRQ_TYPE_EDGE_RISING
++ 0 254 IRQ_TYPE_EDGE_RISING
++ 0 255 IRQ_TYPE_EDGE_RISING>;
++
++ status = "disabled";
++
++ gmac0: gmac0 {
++ local-mac-address = [00 00 00 00 00 00];
++ vlan_tag = <1 0x1f>;
++ };
++
++ gmac1: gmac1 {
++ local-mac-address = [00 00 00 00 00 00];
++ qcom,phy_mdio_addr = <4>;
++ qcom,poll_required = <1>;
++ qcom,forced_speed = <1000>;
++ qcom,forced_duplex = <1>;
++ vlan_tag = <2 0x20>;
++ };
++ };
++
+ usb3_ss_phy: ssphy@9a000 {
+ compatible = "qcom,usb-ss-ipq4019-phy";
+ #phy-cells = <0>;
--- /dev/null
+From c611d3780fa101662a822d10acf8feb04ca97409 Mon Sep 17 00:00:00 2001
+From: Christian Lamparter <chunkeey@gmail.com>
+Date: Sun, 20 Nov 2016 01:01:10 +0100
+Subject: [PATCH] dts: ipq4019: add ethernet ipqess node
+
+This patch adds the device-tree node for the ipqess ethernet
+interfaces.
+
+Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
+---
+ arch/arm/boot/dts/qcom-ipq4019.dtsi | 60 +++++++++++++++++++++++++++++++++++++
+ 1 file changed, 60 insertions(+)
+
+--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
+@@ -617,6 +618,53 @@
+ status = "disabled";
+ };
+
++ gmac: ethernet@c080000 {
++ compatible = "qcom,ipq4019-ess-edma";
++ reg = <0xc080000 0x8000>;
++ interrupts = <GIC_SPI 65 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 66 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 67 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 68 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 69 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 70 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 71 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 72 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 73 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 74 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 76 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 77 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 80 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 240 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 241 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 242 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 243 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 244 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 245 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 246 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 247 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 248 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 249 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 250 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 251 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 252 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 253 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 254 IRQ_TYPE_EDGE_RISING>,
++ <GIC_SPI 255 IRQ_TYPE_EDGE_RISING>;
++
++ status = "disabled";
++
++ phy-mode = "internal";
++ fixed-link {
++ speed = <1000>;
++ full-duplex;
++ pause;
++ asym-pause;
++ };
++ };
++
+ usb3_ss_phy: ssphy@9a000 {
+ compatible = "qcom,usb-ss-ipq4019-phy";
+ #phy-cells = <0>;
--- /dev/null
+From: Christian Lamparter <chunkeey@googlemail.com>
+Subject: SoC: add qualcomm syscon
+--- a/drivers/soc/qcom/Makefile
++++ b/drivers/soc/qcom/Makefile
+@@ -18,6 +18,7 @@ obj-$(CONFIG_QCOM_SMEM_STATE) += smem_st
+ obj-$(CONFIG_QCOM_SMP2P) += smp2p.o
+ obj-$(CONFIG_QCOM_SMSM) += smsm.o
+ obj-$(CONFIG_QCOM_WCNSS_CTRL) += wcnss_ctrl.o
++obj-$(CONFIG_QCOM_TCSR) += qcom_tcsr.o
+ obj-$(CONFIG_QCOM_APR) += apr.o
+ obj-$(CONFIG_QCOM_LLCC) += llcc-slice.o
+ obj-$(CONFIG_QCOM_SDM845_LLCC) += llcc-sdm845.o
+--- a/drivers/soc/qcom/Kconfig
++++ b/drivers/soc/qcom/Kconfig
+@@ -146,6 +146,13 @@ config QCOM_SMSM
+ Say yes here to support the Qualcomm Shared Memory State Machine.
+ The state machine is represented by bits in shared memory.
+
++config QCOM_TCSR
++ tristate "QCOM Top Control and Status Registers"
++ depends on ARCH_QCOM
++ help
++ Say y here to enable TCSR support. The TCSR provides control
++ functions for various peripherals.
++
+ config QCOM_WCNSS_CTRL
+ tristate "Qualcomm WCNSS control driver"
+ depends on ARCH_QCOM
+--- /dev/null
++++ b/drivers/soc/qcom/qcom_tcsr.c
+@@ -0,0 +1,98 @@
++/*
++ * Copyright (c) 2014, The Linux foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License rev 2 and
++ * only rev 2 as published by the free Software foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or fITNESS fOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/clk.h>
++#include <linux/err.h>
++#include <linux/io.h>
++#include <linux/module.h>
++#include <linux/of.h>
++#include <linux/of_platform.h>
++#include <linux/platform_device.h>
++
++#define TCSR_USB_PORT_SEL 0xb0
++#define TCSR_USB_HSPHY_CONFIG 0xC
++
++#define TCSR_ESS_INTERFACE_SEL_OFFSET 0x0
++#define TCSR_ESS_INTERFACE_SEL_MASK 0xf
++
++#define TCSR_WIFI0_GLB_CFG_OFFSET 0x0
++#define TCSR_WIFI1_GLB_CFG_OFFSET 0x4
++#define TCSR_PNOC_SNOC_MEMTYPE_M0_M2 0x4
++
++static int tcsr_probe(struct platform_device *pdev)
++{
++ struct resource *res;
++ const struct device_node *node = pdev->dev.of_node;
++ void __iomem *base;
++ u32 val;
++
++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++ base = devm_ioremap_resource(&pdev->dev, res);
++ if (IS_ERR(base))
++ return PTR_ERR(base);
++
++ if (!of_property_read_u32(node, "qcom,usb-ctrl-select", &val)) {
++ dev_err(&pdev->dev, "setting usb port select = %d\n", val);
++ writel(val, base + TCSR_USB_PORT_SEL);
++ }
++
++ if (!of_property_read_u32(node, "qcom,usb-hsphy-mode-select", &val)) {
++ dev_info(&pdev->dev, "setting usb hs phy mode select = %x\n", val);
++ writel(val, base + TCSR_USB_HSPHY_CONFIG);
++ }
++
++ if (!of_property_read_u32(node, "qcom,ess-interface-select", &val)) {
++ u32 tmp = 0;
++ dev_info(&pdev->dev, "setting ess interface select = %x\n", val);
++ tmp = readl(base + TCSR_ESS_INTERFACE_SEL_OFFSET);
++ tmp = tmp & (~TCSR_ESS_INTERFACE_SEL_MASK);
++ tmp = tmp | (val&TCSR_ESS_INTERFACE_SEL_MASK);
++ writel(tmp, base + TCSR_ESS_INTERFACE_SEL_OFFSET);
++ }
++
++ if (!of_property_read_u32(node, "qcom,wifi_glb_cfg", &val)) {
++ dev_info(&pdev->dev, "setting wifi_glb_cfg = %x\n", val);
++ writel(val, base + TCSR_WIFI0_GLB_CFG_OFFSET);
++ writel(val, base + TCSR_WIFI1_GLB_CFG_OFFSET);
++ }
++
++ if (!of_property_read_u32(node, "qcom,wifi_noc_memtype_m0_m2", &val)) {
++ dev_info(&pdev->dev,
++ "setting wifi_noc_memtype_m0_m2 = %x\n", val);
++ writel(val, base + TCSR_PNOC_SNOC_MEMTYPE_M0_M2);
++ }
++
++ return 0;
++}
++
++static const struct of_device_id tcsr_dt_match[] = {
++ { .compatible = "qcom,tcsr", },
++ { },
++};
++
++MODULE_DEVICE_TABLE(of, tcsr_dt_match);
++
++static struct platform_driver tcsr_driver = {
++ .driver = {
++ .name = "tcsr",
++ .owner = THIS_MODULE,
++ .of_match_table = tcsr_dt_match,
++ },
++ .probe = tcsr_probe,
++};
++
++module_platform_driver(tcsr_driver);
++
++MODULE_AUTHOR("Andy Gross <agross@codeaurora.org>");
++MODULE_DESCRIPTION("QCOM TCSR driver");
++MODULE_LICENSE("GPL v2");
+--- /dev/null
++++ b/include/dt-bindings/soc/qcom,tcsr.h
+@@ -0,0 +1,48 @@
++/* Copyright (c) 2014, The Linux Foundation. All rights reserved.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License version 2 and
++ * only version 2 as published by the Free Software Foundation.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ */
++#ifndef __DT_BINDINGS_QCOM_TCSR_H
++#define __DT_BINDINGS_QCOM_TCSR_H
++
++#define TCSR_USB_SELECT_USB3_P0 0x1
++#define TCSR_USB_SELECT_USB3_P1 0x2
++#define TCSR_USB_SELECT_USB3_DUAL 0x3
++
++/* IPQ40xx HS PHY Mode Select */
++#define TCSR_USB_HSPHY_HOST_MODE 0x00E700E7
++#define TCSR_USB_HSPHY_DEVICE_MODE 0x00C700E7
++
++/* IPQ40xx ess interface mode select */
++#define TCSR_ESS_PSGMII 0
++#define TCSR_ESS_PSGMII_RGMII5 1
++#define TCSR_ESS_PSGMII_RMII0 2
++#define TCSR_ESS_PSGMII_RMII1 4
++#define TCSR_ESS_PSGMII_RMII0_RMII1 6
++#define TCSR_ESS_PSGMII_RGMII4 9
++
++/*
++ * IPQ40xx WiFi Global Config
++ * Bit 30:AXID_EN
++ * Enable AXI master bus Axid translating to confirm all txn submitted by order
++ * Bit 24: Use locally generated socslv_wxi_bvalid
++ * 1: use locally generate socslv_wxi_bvalid for performance.
++ * 0: use SNOC socslv_wxi_bvalid.
++ */
++#define TCSR_WIFI_GLB_CFG 0x41000000
++
++/* IPQ40xx MEM_TYPE_SEL_M0_M2 Select Bit 26:24 - 2 NORMAL */
++#define TCSR_WIFI_NOC_MEMTYPE_M0_M2 0x02222222
++
++/* TCSR A/B REG */
++#define IPQ806X_TCSR_REG_A_ADM_CRCI_MUX_SEL 0
++#define IPQ806X_TCSR_REG_B_ADM_CRCI_MUX_SEL 1
++
++#endif
--- /dev/null
+--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
++++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
+@@ -15,6 +15,7 @@
+ */
+
+ #include "qcom-ipq4019.dtsi"
++#include <dt-bindings/soc/qcom,tcsr.h>
+
+ / {
+ model = "Qualcomm Technologies, Inc. IPQ4019/AP-DK01.1";
+@@ -29,6 +30,32 @@
+ };
+
+ soc {
++ tcsr@194b000 {
++ /* select hostmode */
++ compatible = "qcom,tcsr";
++ reg = <0x194b000 0x100>;
++ qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
++ status = "ok";
++ };
++
++ ess_tcsr@1953000 {
++ compatible = "qcom,tcsr";
++ reg = <0x1953000 0x1000>;
++ qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
++ };
++
++ tcsr@1949000 {
++ compatible = "qcom,tcsr";
++ reg = <0x1949000 0x100>;
++ qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
++ };
++
++ tcsr@1957000 {
++ compatible = "qcom,tcsr";
++ reg = <0x1957000 0x100>;
++ qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
++ };
++
+ rng@22000 {
+ status = "ok";
+ };
+@@ -74,14 +101,6 @@
+ pinctrl-names = "default";
+ status = "ok";
+ cs-gpios = <&tlmm 54 0>;
+-
+- mx25l25635e@0 {
+- #address-cells = <1>;
+- #size-cells = <1>;
+- reg = <0>;
+- compatible = "mx25l25635e";
+- spi-max-frequency = <24000000>;
+- };
+ };
+
+ serial@78af000 {
+@@ -110,6 +129,22 @@
+ status = "ok";
+ };
+
++ mdio@90000 {
++ status = "okay";
++ };
++
++ ess-switch@c000000 {
++ status = "okay";
++ };
++
++ ess-psgmii@98000 {
++ status = "okay";
++ };
++
++ edma@c080000 {
++ status = "okay";
++ };
++
+ usb3_ss_phy: ssphy@9a000 {
+ status = "ok";
+ };
+--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1-c1.dts
++++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1-c1.dts
+@@ -18,5 +18,73 @@
+
+ / {
+ model = "Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1";
++ compatible = "qcom,ap-dk01.1-c1", "qcom,ap-dk01.2-c1";
+
++ memory {
++ device_type = "memory";
++ reg = <0x80000000 0x10000000>;
++ };
++};
++
++&blsp1_spi1 {
++ mx25l25635f@0 {
++ compatible = "mx25l25635f", "jedec,spi-nor";
++ #address-cells = <1>;
++ #size-cells = <1>;
++ reg = <0>;
++ spi-max-frequency = <24000000>;
++
++ SBL1@0 {
++ label = "SBL1";
++ reg = <0x0 0x40000>;
++ read-only;
++ };
++ MIBIB@40000 {
++ label = "MIBIB";
++ reg = <0x40000 0x20000>;
++ read-only;
++ };
++ QSEE@60000 {
++ label = "QSEE";
++ reg = <0x60000 0x60000>;
++ read-only;
++ };
++ CDT@c0000 {
++ label = "CDT";
++ reg = <0xc0000 0x10000>;
++ read-only;
++ };
++ DDRPARAMS@d0000 {
++ label = "DDRPARAMS";
++ reg = <0xd0000 0x10000>;
++ read-only;
++ };
++ APPSBLENV@e0000 {
++ label = "APPSBLENV";
++ reg = <0xe0000 0x10000>;
++ read-only;
++ };
++ APPSBL@f0000 {
++ label = "APPSBL";
++ reg = <0xf0000 0x80000>;
++ read-only;
++ };
++ ART@170000 {
++ label = "ART";
++ reg = <0x170000 0x10000>;
++ read-only;
++ };
++ kernel@180000 {
++ label = "kernel";
++ reg = <0x180000 0x400000>;
++ };
++ rootfs@580000 {
++ label = "rootfs";
++ reg = <0x580000 0x1600000>;
++ };
++ firmware@180000 {
++ label = "firmware";
++ reg = <0x180000 0x1a00000>;
++ };
++ };
+ };
--- /dev/null
+From a10fab12a927e60b7141a602e740d70cb4d09e4a Mon Sep 17 00:00:00 2001
+From: John Crispin <john@phrozen.org>
+Date: Thu, 9 Mar 2017 11:03:18 +0100
+Subject: [PATCH] arm: boot: add dts files
+
+Signed-off-by: John Crispin <john@phrozen.org>
+---
+ arch/arm/boot/dts/Makefile | 23 +++++++++++++++++++++++
+ 1 file changed, 23 insertions(+)
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -785,11 +785,42 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+ qcom-apq8074-dragonboard.dtb \
+ qcom-apq8084-ifc6540.dtb \
+ qcom-apq8084-mtp.dtb \
++ qcom-ipq4018-a42.dtb \
++ qcom-ipq4018-ap120c-ac.dtb \
++ qcom-ipq4018-dap-2610.dtb \
++ qcom-ipq4018-cs-w3-wd1200g-eup.dtb \
++ qcom-ipq4018-ea6350v3.dtb \
++ qcom-ipq4018-eap1300.dtb \
++ qcom-ipq4018-emd1.dtb \
++ qcom-ipq4018-ens620ext.dtb \
++ qcom-ipq4018-ex6100v2.dtb \
++ qcom-ipq4018-ex6150v2.dtb \
++ qcom-ipq4018-fritzbox-4040.dtb \
++ qcom-ipq4018-jalapeno.dtb \
++ qcom-ipq4018-meshpoint-one.dtb \
++ qcom-ipq4018-nbg6617.dtb \
++ qcom-ipq4018-rt-ac58u.dtb \
++ qcom-ipq4018-wre6606.dtb \
+ qcom-ipq4019-ap.dk01.1-c1.dtb \
+ qcom-ipq4019-ap.dk04.1-c1.dtb \
+ qcom-ipq4019-ap.dk04.1-c3.dtb \
+ qcom-ipq4019-ap.dk07.1-c1.dtb \
+ qcom-ipq4019-ap.dk07.1-c2.dtb \
++ qcom-ipq4019-a62.dtb \
++ qcom-ipq4019-fritzbox-7530.dtb \
++ qcom-ipq4019-fritzrepeater-1200.dtb \
++ qcom-ipq4019-fritzrepeater-3000.dtb \
++ qcom-ipq4019-ea8300.dtb \
++ qcom-ipq4019-map-ac2200.dtb \
++ qcom-ipq4019-e2600ac-c1.dtb \
++ qcom-ipq4019-e2600ac-c2.dtb \
++ qcom-ipq4019-u4019-32m.dtb \
++ qcom-ipq4019-wpj419.dtb \
++ qcom-ipq4028-wpj428.dtb \
++ qcom-ipq4029-ap-303.dtb \
++ qcom-ipq4029-ap-303h.dtb \
++ qcom-ipq4029-gl-b1300.dtb \
++ qcom-ipq4029-mr33.dtb \
+ qcom-ipq8064-ap148.dtb \
+ qcom-msm8660-surf.dtb \
+ qcom-msm8960-cdp.dtb \
--- /dev/null
+Index: linux-5.4.5/drivers/of/fdt.c
+===================================================================
+--- linux-5.4.5.orig/drivers/of/fdt.c
++++ linux-5.4.5/drivers/of/fdt.c
+@@ -1059,6 +1059,9 @@ int __init early_init_dt_scan_chosen(uns
+ p = of_get_flat_dt_prop(node, "bootargs", &l);
+ if (p != NULL && l > 0)
+ strlcpy(data, p, min(l, COMMAND_LINE_SIZE));
++ p = of_get_flat_dt_prop(node, "bootargs-append", &l);
++ if (p != NULL && l > 0)
++ strlcat(data, p, min_t(int, strlen(data) + (int)l, COMMAND_LINE_SIZE));
+
+ /*
+ * CONFIG_CMDLINE is meant to be a default in case nothing else