--- /dev/null
+#include "qcom-ipq8064-v1.0.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "TP-Link Archer C2600";
+ compatible = "tplink,c2600", "qcom,ipq8064";
+
+ memory@0 {
+ reg = <0x42000000 0x1e000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &uart4;
+ mdio-gpio0 = &mdio0;
+ };
+
+ chosen {
+ linux,stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ pinmux@800000 {
+ i2c4_pins: i2c4_pinmux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ bias-disable;
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ drive-strength = <10>;
+ bias-none;
+ };
+ };
+
+ nand_pins: nand_pins {
+ mux {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38", "gpio39",
+ "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+
+ pullups {
+ pins = "gpio39";
+ bias-pull-up;
+ };
+
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ bias-bus-hold;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+ };
+
+ gsbi@16300000 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "ok";
+ serial@16340000 {
+ status = "ok";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+ };
+
+ gsbi5: gsbi@1a200000 {
+ qcom,mode = <GSBI_PROT_SPI>;
+ status = "ok";
+
+ spi4: spi@1a280000 {
+ status = "ok";
+ spi-max-frequency = <50000000>;
+
+ pinctrl-0 = <&spi_pins>;
+ pinctrl-names = "default";
+
+ cs-gpios = <&qcom_pinmux 20 0>;
+
+ flash: m25p80@0 {
+ compatible = "s25fl256s1";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+
+ SBL1@0 {
+ label = "SBL1";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+ MIBIB@20000 {
+ label = "MIBIB";
+ reg = <0x20000 0x20000>;
+ read-only;
+ };
+ SBL2@40000 {
+ label = "SBL2";
+ reg = <0x40000 0x20000>;
+ read-only;
+ };
+ SBL3@60000 {
+ label = "SBL3";
+ reg = <0x60000 0x30000>;
+ read-only;
+ };
+ DDRCONFIG@90000 {
+ label = "DDRCONFIG";
+ reg = <0x90000 0x10000>;
+ read-only;
+ };
+ SSD@a0000 {
+ label = "SSD";
+ reg = <0xa0000 0x10000>;
+ read-only;
+ };
+ TZ@b0000 {
+ label = "TZ";
+ reg = <0xb0000 0x30000>;
+ read-only;
+ };
+ RPM@e0000 {
+ label = "RPM";
+ reg = <0xe0000 0x20000>;
+ read-only;
+ };
+ fs-uboot@100000 {
+ label = "fs-uboot";
+ reg = <0x100000 0x70000>;
+ read-only;
+ };
+ uboot-env@170000 {
+ label = "uboot-env";
+ reg = <0x170000 0x40000>;
+ read-only;
+ };
+ radio@1b0000 {
+ label = "radio";
+ reg = <0x1b0000 0x40000>;
+ read-only;
+ };
+ os-image@1f0000 {
+ label = "os-image";
+ reg = <0x1f0000 0x200000>;
+ };
+ rootfs@3f0000 {
+ label = "rootfs";
+ reg = <0x3f0000 0x1b00000>;
+ };
+ defaultmac: default-mac@1ef0000 {
+ label = "default-mac";
+ reg = <0x1ef0000 0x00200>;
+ read-only;
+ };
+ pin@1ef0200 {
+ label = "pin";
+ reg = <0x1ef0200 0x00200>;
+ read-only;
+ };
+ product-info@1ef0400 {
+ label = "product-info";
+ reg = <0x1ef0400 0x0fc00>;
+ read-only;
+ };
+ partition-table@1f00000 {
+ label = "partition-table";
+ reg = <0x1f00000 0x10000>;
+ read-only;
+ };
+ soft-version@1f10000 {
+ label = "soft-version";
+ reg = <0x1f10000 0x10000>;
+ read-only;
+ };
+ support-list@1f20000 {
+ label = "support-list";
+ reg = <0x1f20000 0x10000>;
+ read-only;
+ };
+ profile@1f30000 {
+ label = "profile";
+ reg = <0x1f30000 0x10000>;
+ read-only;
+ };
+ default-config@1f40000 {
+ label = "default-config";
+ reg = <0x1f40000 0x10000>;
+ read-only;
+ };
+ user-config@1f50000 {
+ label = "user-config";
+ reg = <0x1f50000 0x40000>;
+ read-only;
+ };
+ qos-db@1f90000 {
+ label = "qos-db";
+ reg = <0x1f90000 0x40000>;
+ read-only;
+ };
+ usb-config@1fd0000 {
+ label = "usb-config";
+ reg = <0x1fd0000 0x10000>;
+ read-only;
+ };
+ log@1fe0000 {
+ label = "log";
+ reg = <0x1fe0000 0x20000>;
+ read-only;
+ };
+ };
+ };
+ };
+
+ phy@100f8800 { /* USB3 port 1 HS phy */
+ status = "ok";
+ };
+
+ phy@100f8830 { /* USB3 port 1 SS phy */
+ status = "ok";
+ };
+
+ phy@110f8800 { /* USB3 port 0 HS phy */
+ status = "ok";
+ };
+
+ phy@110f8830 { /* USB3 port 0 SS phy */
+ status = "ok";
+ };
+
+ usb30@0 {
+ status = "ok";
+ };
+
+ usb30@1 {
+ status = "ok";
+ };
+
+ pcie0: pci@1b500000 {
+ status = "ok";
+ phy-tx0-term-offset = <7>;
+ };
+
+ pcie1: pci@1b700000 {
+ status = "ok";
+ phy-tx0-term-offset = <7>;
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0xaa545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
+ };
+
+ phy4: ethernet-phy@4 {
+ device_type = "ethernet-phy";
+ reg = <4>;
+ };
+ };
+
+ gmac1: ethernet@37200000 {
+ status = "ok";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&defaultmac 0x8>;
+ mtd-mac-address-increment = <1>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ gmac2: ethernet@37400000 {
+ status = "ok";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&defaultmac 0x8>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ wifi {
+ label = "wifi";
+ gpios = <&qcom_pinmux 49 1>;
+ linux,code = <KEY_WLAN>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 64 1>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 1>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ ledgeneral {
+ label = "ledgeneral";
+ gpios = <&qcom_pinmux 16 1>;
+ linux,code = <KEY_DOLLAR>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ lan {
+ label = "lan:blue";
+ gpios = <&qcom_pinmux 6 0>;
+ };
+ usb4 {
+ label = "usb_4:blue";
+ gpios = <&qcom_pinmux 7 0>;
+ };
+ usb2 {
+ label = "usb_2:blue";
+ gpios = <&qcom_pinmux 8 0>;
+ };
+ wps {
+ label = "wps:blue";
+ gpios = <&qcom_pinmux 9 0>;
+ };
+ wan_blue {
+ label = "wan:blue";
+ gpios = <&qcom_pinmux 33 1>;
+ };
+ status {
+ label = "status:blue";
+ gpios = <&qcom_pinmux 53 0>;
+ default-state = "on";
+ };
+ ledgnr {
+ label = "ledgnr:blue";
+ gpios = <&qcom_pinmux 66 0>;
+ };
+ };
+};
+
+&adm_dma {
+ status = "ok";
+};
--- /dev/null
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Netgear Nighthawk X4 D7800";
+ compatible = "netgear,d7800", "qcom,ipq8064";
+
+ memory@0 {
+ reg = <0x42000000 0xe000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &uart4;
+ mdio-gpio0 = &mdio0;
+ };
+
+ chosen {
+ bootargs = "rootfstype=squashfs noinitrd";
+ linux,stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ pinmux@800000 {
+ i2c4_pins: i2c4_pinmux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ bias-disable;
+ };
+
+ pcie0_pins: pcie0_pinmux {
+ mux {
+ pins = "gpio3";
+ function = "pcie1_rst";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ pcie1_pins: pcie1_pinmux {
+ mux {
+ pins = "gpio48";
+ function = "pcie2_rst";
+ drive-strength = <12>;
+ bias-disable;
+ };
+ };
+
+ nand_pins: nand_pins {
+ mux {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38", "gpio39",
+ "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+ pullups {
+ pins = "gpio39";
+ bias-pull-up;
+ };
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ bias-bus-hold;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+ };
+
+ gsbi@16300000 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "ok";
+ serial@16340000 {
+ status = "ok";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+ };
+
+ sata-phy@1b400000 {
+ status = "ok";
+ };
+
+ sata@29000000 {
+ status = "ok";
+ };
+
+ phy@100f8800 { /* USB3 port 1 HS phy */
+ status = "ok";
+ };
+
+ phy@100f8830 { /* USB3 port 1 SS phy */
+ status = "ok";
+ };
+
+ phy@110f8800 { /* USB3 port 0 HS phy */
+ status = "ok";
+ };
+
+ phy@110f8830 { /* USB3 port 0 SS phy */
+ status = "ok";
+ };
+
+ usb30@0 {
+ status = "ok";
+ };
+
+ usb30@1 {
+ status = "ok";
+ };
+
+ pcie0: pci@1b500000 {
+ status = "ok";
+ reset-gpio = <&qcom_pinmux 3 0>;
+ pinctrl-0 = <&pcie0_pins>;
+ pinctrl-names = "default";
+ };
+
+ pcie1: pci@1b700000 {
+ status = "ok";
+ reset-gpio = <&qcom_pinmux 48 0>;
+ pinctrl-0 = <&pcie1_pins>;
+ pinctrl-names = "default";
+ };
+
+ nand@1ac00000 {
+ status = "ok";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qcadata@0 {
+ label = "qcadata";
+ reg = <0x0000000 0x0c80000>;
+ read-only;
+ };
+
+ APPSBL@c80000 {
+ label = "APPSBL";
+ reg = <0x0c80000 0x0500000>;
+ read-only;
+ };
+
+ APPSBLENV@1180000 {
+ label = "APPSBLENV";
+ reg = <0x1180000 0x0080000>;
+ read-only;
+ };
+
+ art: art@1200000 {
+ label = "art";
+ reg = <0x1200000 0x0140000>;
+ read-only;
+ };
+
+ artbak: art@1340000 {
+ label = "artbak";
+ reg = <0x1340000 0x0140000>;
+ read-only;
+ };
+
+ kernel@1480000 {
+ label = "kernel";
+ reg = <0x1480000 0x0200000>;
+ };
+
+ ubi@1680000 {
+ label = "ubi";
+ reg = <0x1680000 0x1E00000>;
+ };
+
+ netgear@3480000 {
+ label = "netgear";
+ reg = <0x3480000 0x4480000>;
+ read-only;
+ };
+
+ reserve@7900000 {
+ label = "reserve";
+ reg = <0x7900000 0x0700000>;
+ read-only;
+ };
+
+ firmware@1480000 {
+ label = "firmware";
+ reg = <0x1480000 0x2000000>;
+ };
+
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0xaa545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
+ };
+
+ phy4: ethernet-phy@4 {
+ device_type = "ethernet-phy";
+ reg = <4>;
+ };
+ };
+
+ gmac1: ethernet@37200000 {
+ status = "ok";
+ phy-mode = "rgmii";
+ phy-handle = <&phy4>;
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&art 6>;
+ };
+
+ gmac2: ethernet@37400000 {
+ status = "ok";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&art 0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ wifi {
+ label = "wifi";
+ gpios = <&qcom_pinmux 6 1>;
+ linux,code = <KEY_WLAN>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 54 1>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 1>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ usb1 {
+ label = "d7800:amber:usb1";
+ gpios = <&qcom_pinmux 7 0>;
+ };
+
+ usb3 {
+ label = "d7800:amber:usb3";
+ gpios = <&qcom_pinmux 8 0>;
+ };
+
+ status {
+ label = "d7800:amber:status";
+ gpios = <&qcom_pinmux 9 0>;
+ };
+
+ internet {
+ label = "d7800:white:internet";
+ gpios = <&qcom_pinmux 22 0>;
+ };
+
+ wan {
+ label = "d7800:white:wan";
+ gpios = <&qcom_pinmux 23 0>;
+ };
+
+ wps {
+ label = "d7800:white:wps";
+ gpios = <&qcom_pinmux 24 0>;
+ };
+
+ esata {
+ label = "d7800:white:esata";
+ gpios = <&qcom_pinmux 26 0>;
+ };
+
+ power {
+ label = "d7800:white:power";
+ gpios = <&qcom_pinmux 53 0>;
+ default-state = "on";
+ };
+
+ rfkill {
+ label = "d7800:white:rfkill";
+ gpios = <&qcom_pinmux 64 0>;
+ };
+
+ wifi5g {
+ label = "d7800:white:wifi5g";
+ gpios = <&qcom_pinmux 67 0>;
+ };
+ };
+};
+
+&adm_dma {
+ status = "ok";
+};
--- /dev/null
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Linksys EA8500 WiFi Router";
+ compatible = "linksys,ea8500", "qcom,ipq8064";
+
+ memory@0 {
+ reg = <0x42000000 0x1e000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &uart4;
+ mdio-gpio0 = &mdio0;
+ };
+
+ chosen {
+ bootargs = "console=ttyMSM0,115200n8";
+ linux,stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ pinmux@800000 {
+ i2c4_pins: i2c4_pinmux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ bias-disable;
+ };
+
+ spi_pins: spi_pins {
+ mux {
+ pins = "gpio18", "gpio19", "gpio21";
+ function = "gsbi5";
+ drive-strength = <10>;
+ bias-none;
+ };
+ };
+ nand_pins: nand_pins {
+ mux {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38", "gpio39",
+ "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+ pullups {
+ pins = "gpio39";
+ bias-pull-up;
+ };
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ bias-bus-hold;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+
+
+ };
+
+ gsbi@16300000 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "ok";
+ serial@16340000 {
+ status = "ok";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+ };
+
+ sata-phy@1b400000 {
+ status = "ok";
+ };
+
+ sata@29000000 {
+ status = "ok";
+ };
+
+ phy@100f8800 { /* USB3 port 1 HS phy */
+ status = "ok";
+ };
+
+ phy@100f8830 { /* USB3 port 1 SS phy */
+ status = "ok";
+ };
+
+ phy@110f8800 { /* USB3 port 0 HS phy */
+ status = "ok";
+ };
+
+ phy@110f8830 { /* USB3 port 0 SS phy */
+ status = "ok";
+ };
+
+ usb30@0 {
+ status = "ok";
+ };
+
+ usb30@1 {
+ status = "ok";
+ };
+
+ pcie0: pci@1b500000 {
+ status = "ok";
+ phy-tx0-term-offset = <7>;
+ };
+
+ pcie1: pci@1b700000 {
+ status = "ok";
+ phy-tx0-term-offset = <7>;
+ };
+
+ pcie2: pci@1b900000 {
+ status = "ok";
+ phy-tx0-term-offset = <7>;
+ };
+
+ nand@1ac00000 {
+ status = "ok";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ SBL1@0 {
+ label = "SBL1";
+ reg = <0x0000000 0x0040000>;
+ read-only;
+ };
+
+ MIBIB@40000 {
+ label = "MIBIB";
+ reg = <0x0040000 0x0140000>;
+ read-only;
+ };
+
+ SBL2@180000 {
+ label = "SBL2";
+ reg = <0x0180000 0x0140000>;
+ read-only;
+ };
+
+ SBL3@2c0000 {
+ label = "SBL3";
+ reg = <0x02c0000 0x0280000>;
+ read-only;
+ };
+
+ DDRCONFIG@540000 {
+ label = "DDRCONFIG";
+ reg = <0x0540000 0x0120000>;
+ read-only;
+ };
+
+ SSD@660000 {
+ label = "SSD";
+ reg = <0x0660000 0x0120000>;
+ read-only;
+ };
+
+ TZ@780000 {
+ label = "TZ";
+ reg = <0x0780000 0x0280000>;
+ read-only;
+ };
+
+ RPM@a00000 {
+ label = "RPM";
+ reg = <0x0a00000 0x0280000>;
+ read-only;
+ };
+
+ art: art@c80000 {
+ label = "art";
+ reg = <0x0c80000 0x0140000>;
+ read-only;
+ };
+
+ APPSBL@dc0000 {
+ label = "APPSBL";
+ reg = <0x0dc0000 0x0100000>;
+ read-only;
+ };
+
+ u_env@ec0000 {
+ label = "u_env";
+ reg = <0x0ec0000 0x0040000>;
+ };
+
+ s_env@f00000 {
+ label = "s_env";
+ reg = <0x0f00000 0x0040000>;
+ };
+
+ devinfo@f40000 {
+ label = "devinfo";
+ reg = <0x0f40000 0x0040000>;
+ };
+
+ linux@f80000 {
+ label = "kernel1";
+ reg = <0x0f80000 0x2800000>; /* 3 MB spill to rootfs*/
+ };
+
+ rootfs@1280000 {
+ label = "rootfs1";
+ reg = <0x1280000 0x2500000>;
+ };
+
+ linux2@3780000 {
+ label = "kernel2";
+ reg = <0x3780000 0x2800000>;
+ };
+
+ rootfs2@3a80000 {
+ label = "rootfs2";
+ reg = <0x3a80000 0x2500000>;
+ };
+
+ syscfg@5f80000 {
+ label = "syscfg";
+ reg = <0x5f80000 0x2080000>;
+ };
+
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0xaa545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
+ };
+
+ phy4: ethernet-phy@4 {
+ device_type = "ethernet-phy";
+ reg = <4>;
+ };
+ };
+
+ gmac1: ethernet@37200000 {
+ status = "ok";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+ qcom,phy_mdio_addr = <4>;
+ qcom,poll_required = <1>;
+ qcom,rgmii_delay = <0>;
+ qcom,emulation = <0>;
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ //lan
+ gmac2: ethernet@37400000 {
+ status = "ok";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+ qcom,phy_mdio_addr = <0>; /* none */
+ qcom,poll_required = <0>; /* no polling */
+ qcom,rgmii_delay = <0>;
+ qcom,emulation = <0>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ adm_dma: dma@18300000 {
+ status = "ok";
+ };
+
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ rfkill {
+ label = "rfkill"; /* WIFI on-off*/
+ gpios = <&qcom_pinmux 67 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RFKILL>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART >;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ wps {
+ label = "ea8500:green:wps";
+ gpios = <&qcom_pinmux 53 0>;
+ default-state = "off";
+ };
+
+ power {
+ label = "ea8500:white:power";
+ gpios = <&qcom_pinmux 6 1>;
+ default-state = "off";
+ linux,default-trigger = "heartbeat";
+ };
+
+ wifi {
+ label = "ea8500:green:wifi";
+ gpios = <&qcom_pinmux 54 0>;
+ default-state = "off";
+ };
+ };
+};
--- /dev/null
+#include "qcom-ipq8064-v1.0.dtsi"
+
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Netgear Nighthawk X4 R7500";
+ compatible = "netgear,r7500", "qcom,ipq8064";
+
+ memory@0 {
+ reg = <0x42000000 0xe000000>;
+ device_type = "memory";
+ };
+
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ rsvd@41200000 {
+ reg = <0x41200000 0x300000>;
+ no-map;
+ };
+ };
+
+ aliases {
+ serial0 = &uart4;
+ mdio-gpio0 = &mdio0;
+ };
+
+ chosen {
+ bootargs = "rootfstype=squashfs noinitrd";
+ linux,stdout-path = "serial0:115200n8";
+ };
+
+ soc {
+ pinmux@800000 {
+ i2c4_pins: i2c4_pinmux {
+ pins = "gpio12", "gpio13";
+ function = "gsbi4";
+ bias-disable;
+ };
+
+ nand_pins: nand_pins {
+ mux {
+ pins = "gpio34", "gpio35", "gpio36",
+ "gpio37", "gpio38", "gpio39",
+ "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ function = "nand";
+ drive-strength = <10>;
+ bias-disable;
+ };
+ pullups {
+ pins = "gpio39";
+ bias-pull-up;
+ };
+ hold {
+ pins = "gpio40", "gpio41", "gpio42",
+ "gpio43", "gpio44", "gpio45",
+ "gpio46", "gpio47";
+ bias-bus-hold;
+ };
+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ pins = "gpio0", "gpio1";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+
+ rgmii2_pins: rgmii2_pins {
+ mux {
+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
+ function = "rgmii2";
+ drive-strength = <8>;
+ bias-disable;
+ };
+ };
+ };
+
+ gsbi@16300000 {
+ qcom,mode = <GSBI_PROT_I2C_UART>;
+ status = "ok";
+ serial@16340000 {
+ status = "ok";
+ };
+ /*
+ * The i2c device on gsbi4 should not be enabled.
+ * On ipq806x designs gsbi4 i2c is meant for exclusive
+ * RPM usage. Turning this on in kernel manifests as
+ * i2c failure for the RPM.
+ */
+ };
+
+ sata-phy@1b400000 {
+ status = "ok";
+ };
+
+ sata@29000000 {
+ status = "ok";
+ };
+
+ phy@100f8800 { /* USB3 port 1 HS phy */
+ status = "ok";
+ };
+
+ phy@100f8830 { /* USB3 port 1 SS phy */
+ status = "ok";
+ };
+
+ phy@110f8800 { /* USB3 port 0 HS phy */
+ status = "ok";
+ };
+
+ phy@110f8830 { /* USB3 port 0 SS phy */
+ status = "ok";
+ };
+
+ usb30@0 {
+ status = "ok";
+ };
+
+ usb30@1 {
+ status = "ok";
+ };
+
+ pcie0: pci@1b500000 {
+ status = "ok";
+ };
+
+ pcie1: pci@1b700000 {
+ status = "ok";
+ };
+
+ nand@1ac00000 {
+ status = "ok";
+
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+
+ nand-ecc-strength = <4>;
+ nand-bus-width = <8>;
+
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ qcadata@0 {
+ label = "qcadata";
+ reg = <0x0000000 0x0c80000>;
+ read-only;
+ };
+
+ APPSBL@c80000 {
+ label = "APPSBL";
+ reg = <0x0c80000 0x0500000>;
+ read-only;
+ };
+
+ APPSBLENV@1180000 {
+ label = "APPSBLENV";
+ reg = <0x1180000 0x0080000>;
+ read-only;
+ };
+
+ art: art@1200000 {
+ label = "art";
+ reg = <0x1200000 0x0140000>;
+ read-only;
+ };
+
+ kernel@1340000 {
+ label = "kernel";
+ reg = <0x1340000 0x0200000>;
+ };
+
+ ubi@1540000 {
+ label = "ubi";
+ reg = <0x1540000 0x1800000>;
+ };
+
+ netgear@2d40000 {
+ label = "netgear";
+ reg = <0x2d40000 0x0c00000>;
+ read-only;
+ };
+
+ reserve@3940000 {
+ label = "reserve";
+ reg = <0x3940000 0x46c0000>;
+ read-only;
+ };
+
+ firmware@1340000 {
+ label = "firmware";
+ reg = <0x1340000 0x1a00000>;
+ };
+
+ };
+
+ mdio0: mdio {
+ compatible = "virtual,mdio-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
+ pinctrl-0 = <&mdio0_pins>;
+ pinctrl-names = "default";
+
+ phy0: ethernet-phy@0 {
+ device_type = "ethernet-phy";
+ reg = <0>;
+ qca,ar8327-initvals = <
+ 0x00004 0x7600000 /* PAD0_MODE */
+ 0x00008 0x1000000 /* PAD5_MODE */
+ 0x0000c 0x80 /* PAD6_MODE */
+ 0x000e4 0xaa545 /* MAC_POWER_SEL */
+ 0x000e0 0xc74164de /* SGMII_CTRL */
+ 0x0007c 0x4e /* PORT0_STATUS */
+ 0x00094 0x4e /* PORT6_STATUS */
+ >;
+ };
+
+ phy4: ethernet-phy@4 {
+ device_type = "ethernet-phy";
+ reg = <4>;
+ };
+ };
+
+ gmac1: ethernet@37200000 {
+ status = "ok";
+ phy-mode = "rgmii";
+ qcom,id = <1>;
+
+ pinctrl-0 = <&rgmii2_pins>;
+ pinctrl-names = "default";
+
+ mtd-mac-address = <&art 6>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ gmac2: ethernet@37400000 {
+ status = "ok";
+ phy-mode = "sgmii";
+ qcom,id = <2>;
+
+ mtd-mac-address = <&art 0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ wifi {
+ label = "wifi";
+ gpios = <&qcom_pinmux 6 1>;
+ linux,code = <KEY_WLAN>;
+ };
+
+ reset {
+ label = "reset";
+ gpios = <&qcom_pinmux 54 1>;
+ linux,code = <KEY_RESTART>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&qcom_pinmux 65 1>;
+ linux,code = <KEY_WPS_BUTTON>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ usb1 {
+ label = "r7500:amber:usb1";
+ gpios = <&qcom_pinmux 7 0>;
+ };
+
+ usb3 {
+ label = "r7500:amber:usb3";
+ gpios = <&qcom_pinmux 8 0>;
+ };
+
+ status {
+ label = "r7500:amber:status";
+ gpios = <&qcom_pinmux 9 0>;
+ };
+
+ internet {
+ label = "r7500:white:internet";
+ gpios = <&qcom_pinmux 22 0>;
+ };
+
+ wan {
+ label = "r7500:white:wan";
+ gpios = <&qcom_pinmux 23 0>;
+ };
+
+ wps {
+ label = "r7500:white:wps";
+ gpios = <&qcom_pinmux 24 0>;
+ };
+
+ esata {
+ label = "r7500:white:esata";
+ gpios = <&qcom_pinmux 26 0>;
+ };
+
+ power {
+ label = "r7500:white:power";
+ gpios = <&qcom_pinmux 53 0>;
+ default-state = "on";
+ };
+
+ rfkill {
+ label = "r7500:white:rfkill";
+ gpios = <&qcom_pinmux 64 0>;
+ };
+
+ wifi5g {
+ label = "r7500:white:wifi5g";
+ gpios = <&qcom_pinmux 67 0>;
+ };
+ };
+};
+
+&adm_dma {
+ status = "ok";
+};
+++ /dev/null
-From 7e77aa188a7a7c4391856a9e5ef5ef58f769e679 Mon Sep 17 00:00:00 2001
-From: Jonas Gorski <jogo@openwrt.org>
-Date: Sun, 9 Aug 2015 13:02:38 +0200
-Subject: [PATCH] ARM: qcom: add Netgear Nighthawk X4 R7500 device tree
-
-Signed-off-by: Jonas Gorski <jogo@openwrt.org>
----
- arch/arm/boot/dts/Makefile | 1 +
- arch/arm/boot/dts/qcom-ipq8064-r7500.dts | 370 +++++++++++++++++++++++++++++++
- 2 files changed, 371 insertions(+)
- create mode 100644 arch/arm/boot/dts/qcom-ipq8064-r7500.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -452,6 +452,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
- qcom-apq8084-mtp.dtb \
- qcom-ipq8064-ap148.dtb \
- qcom-ipq8064-db149.dtb \
-+ qcom-ipq8064-r7500.dtb \
- qcom-msm8660-surf.dtb \
- qcom-msm8960-cdp.dtb \
- qcom-msm8974-sony-xperia-honami.dtb
---- /dev/null
-+++ b/arch/arm/boot/dts/qcom-ipq8064-r7500.dts
-@@ -0,0 +1,342 @@
-+#include "qcom-ipq8064-v1.0.dtsi"
-+
-+#include <dt-bindings/input/input.h>
-+
-+/ {
-+ model = "Netgear Nighthawk X4 R7500";
-+ compatible = "netgear,r7500", "qcom,ipq8064";
-+
-+ memory@0 {
-+ reg = <0x42000000 0xe000000>;
-+ device_type = "memory";
-+ };
-+
-+ reserved-memory {
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ ranges;
-+ rsvd@41200000 {
-+ reg = <0x41200000 0x300000>;
-+ no-map;
-+ };
-+ };
-+
-+ aliases {
-+ serial0 = &uart4;
-+ mdio-gpio0 = &mdio0;
-+ };
-+
-+ chosen {
-+ bootargs = "rootfstype=squashfs noinitrd";
-+ linux,stdout-path = "serial0:115200n8";
-+ };
-+
-+ soc {
-+ pinmux@800000 {
-+ i2c4_pins: i2c4_pinmux {
-+ pins = "gpio12", "gpio13";
-+ function = "gsbi4";
-+ bias-disable;
-+ };
-+
-+ nand_pins: nand_pins {
-+ mux {
-+ pins = "gpio34", "gpio35", "gpio36",
-+ "gpio37", "gpio38", "gpio39",
-+ "gpio40", "gpio41", "gpio42",
-+ "gpio43", "gpio44", "gpio45",
-+ "gpio46", "gpio47";
-+ function = "nand";
-+ drive-strength = <10>;
-+ bias-disable;
-+ };
-+ pullups {
-+ pins = "gpio39";
-+ bias-pull-up;
-+ };
-+ hold {
-+ pins = "gpio40", "gpio41", "gpio42",
-+ "gpio43", "gpio44", "gpio45",
-+ "gpio46", "gpio47";
-+ bias-bus-hold;
-+ };
-+ };
-+
-+ mdio0_pins: mdio0_pins {
-+ mux {
-+ pins = "gpio0", "gpio1";
-+ function = "gpio";
-+ drive-strength = <8>;
-+ bias-disable;
-+ };
-+ };
-+
-+ rgmii2_pins: rgmii2_pins {
-+ mux {
-+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
-+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
-+ function = "rgmii2";
-+ drive-strength = <8>;
-+ bias-disable;
-+ };
-+ };
-+ };
-+
-+ gsbi@16300000 {
-+ qcom,mode = <GSBI_PROT_I2C_UART>;
-+ status = "ok";
-+ serial@16340000 {
-+ status = "ok";
-+ };
-+ /*
-+ * The i2c device on gsbi4 should not be enabled.
-+ * On ipq806x designs gsbi4 i2c is meant for exclusive
-+ * RPM usage. Turning this on in kernel manifests as
-+ * i2c failure for the RPM.
-+ */
-+ };
-+
-+ sata-phy@1b400000 {
-+ status = "ok";
-+ };
-+
-+ sata@29000000 {
-+ status = "ok";
-+ };
-+
-+ phy@100f8800 { /* USB3 port 1 HS phy */
-+ status = "ok";
-+ };
-+
-+ phy@100f8830 { /* USB3 port 1 SS phy */
-+ status = "ok";
-+ };
-+
-+ phy@110f8800 { /* USB3 port 0 HS phy */
-+ status = "ok";
-+ };
-+
-+ phy@110f8830 { /* USB3 port 0 SS phy */
-+ status = "ok";
-+ };
-+
-+ usb30@0 {
-+ status = "ok";
-+ };
-+
-+ usb30@1 {
-+ status = "ok";
-+ };
-+
-+ pcie0: pci@1b500000 {
-+ status = "ok";
-+ };
-+
-+ pcie1: pci@1b700000 {
-+ status = "ok";
-+ };
-+
-+ nand@1ac00000 {
-+ status = "ok";
-+
-+ pinctrl-0 = <&nand_pins>;
-+ pinctrl-names = "default";
-+
-+ nand-ecc-strength = <4>;
-+ nand-bus-width = <8>;
-+
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+
-+ qcadata@0 {
-+ label = "qcadata";
-+ reg = <0x0000000 0x0c80000>;
-+ read-only;
-+ };
-+
-+ APPSBL@c80000 {
-+ label = "APPSBL";
-+ reg = <0x0c80000 0x0500000>;
-+ read-only;
-+ };
-+
-+ APPSBLENV@1180000 {
-+ label = "APPSBLENV";
-+ reg = <0x1180000 0x0080000>;
-+ read-only;
-+ };
-+
-+ art: art@1200000 {
-+ label = "art";
-+ reg = <0x1200000 0x0140000>;
-+ read-only;
-+ };
-+
-+ kernel@1340000 {
-+ label = "kernel";
-+ reg = <0x1340000 0x0200000>;
-+ };
-+
-+ ubi@1540000 {
-+ label = "ubi";
-+ reg = <0x1540000 0x1800000>;
-+ };
-+
-+ netgear@2d40000 {
-+ label = "netgear";
-+ reg = <0x2d40000 0x0c00000>;
-+ read-only;
-+ };
-+
-+ reserve@3940000 {
-+ label = "reserve";
-+ reg = <0x3940000 0x46c0000>;
-+ read-only;
-+ };
-+
-+ firmware@1340000 {
-+ label = "firmware";
-+ reg = <0x1340000 0x1a00000>;
-+ };
-+
-+ };
-+
-+ mdio0: mdio {
-+ compatible = "virtual,mdio-gpio";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
-+ pinctrl-0 = <&mdio0_pins>;
-+ pinctrl-names = "default";
-+
-+ phy0: ethernet-phy@0 {
-+ device_type = "ethernet-phy";
-+ reg = <0>;
-+ qca,ar8327-initvals = <
-+ 0x00004 0x7600000 /* PAD0_MODE */
-+ 0x00008 0x1000000 /* PAD5_MODE */
-+ 0x0000c 0x80 /* PAD6_MODE */
-+ 0x000e4 0xaa545 /* MAC_POWER_SEL */
-+ 0x000e0 0xc74164de /* SGMII_CTRL */
-+ 0x0007c 0x4e /* PORT0_STATUS */
-+ 0x00094 0x4e /* PORT6_STATUS */
-+ >;
-+ };
-+
-+ phy4: ethernet-phy@4 {
-+ device_type = "ethernet-phy";
-+ reg = <4>;
-+ };
-+ };
-+
-+ gmac1: ethernet@37200000 {
-+ status = "ok";
-+ phy-mode = "rgmii";
-+ qcom,id = <1>;
-+
-+ pinctrl-0 = <&rgmii2_pins>;
-+ pinctrl-names = "default";
-+
-+ mtd-mac-address = <&art 6>;
-+
-+ fixed-link {
-+ speed = <1000>;
-+ full-duplex;
-+ };
-+ };
-+
-+ gmac2: ethernet@37400000 {
-+ status = "ok";
-+ phy-mode = "sgmii";
-+ qcom,id = <2>;
-+
-+ mtd-mac-address = <&art 0>;
-+
-+ fixed-link {
-+ speed = <1000>;
-+ full-duplex;
-+ };
-+ };
-+ };
-+
-+ gpio-keys {
-+ compatible = "gpio-keys";
-+
-+ wifi {
-+ label = "wifi";
-+ gpios = <&qcom_pinmux 6 1>;
-+ linux,code = <KEY_WLAN>;
-+ };
-+
-+ reset {
-+ label = "reset";
-+ gpios = <&qcom_pinmux 54 1>;
-+ linux,code = <KEY_RESTART>;
-+ };
-+
-+ wps {
-+ label = "wps";
-+ gpios = <&qcom_pinmux 65 1>;
-+ linux,code = <KEY_WPS_BUTTON>;
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+
-+ usb1 {
-+ label = "r7500:amber:usb1";
-+ gpios = <&qcom_pinmux 7 0>;
-+ };
-+
-+ usb3 {
-+ label = "r7500:amber:usb3";
-+ gpios = <&qcom_pinmux 8 0>;
-+ };
-+
-+ status {
-+ label = "r7500:amber:status";
-+ gpios = <&qcom_pinmux 9 0>;
-+ };
-+
-+ internet {
-+ label = "r7500:white:internet";
-+ gpios = <&qcom_pinmux 22 0>;
-+ };
-+
-+ wan {
-+ label = "r7500:white:wan";
-+ gpios = <&qcom_pinmux 23 0>;
-+ };
-+
-+ wps {
-+ label = "r7500:white:wps";
-+ gpios = <&qcom_pinmux 24 0>;
-+ };
-+
-+ esata {
-+ label = "r7500:white:esata";
-+ gpios = <&qcom_pinmux 26 0>;
-+ };
-+
-+ power {
-+ label = "r7500:white:power";
-+ gpios = <&qcom_pinmux 53 0>;
-+ default-state = "on";
-+ };
-+
-+ rfkill {
-+ label = "r7500:white:rfkill";
-+ gpios = <&qcom_pinmux 64 0>;
-+ };
-+
-+ wifi5g {
-+ label = "r7500:white:wifi5g";
-+ gpios = <&qcom_pinmux 67 0>;
-+ };
-+ };
-+};
-+
-+&adm_dma {
-+ status = "ok";
-+};
--- /dev/null
+From 7e77aa188a7a7c4391856a9e5ef5ef58f769e679 Mon Sep 17 00:00:00 2001
+From: Jonas Gorski <jogo@openwrt.org>
+Date: Sun, 9 Aug 2015 13:02:38 +0200
+Subject: [PATCH] ARM: qcom: add Netgear Nighthawk X4 R7500 device tree
+
+Signed-off-by: Jonas Gorski <jogo@openwrt.org>
+---
+ arch/arm/boot/dts/Makefile | 1 +
+ arch/arm/boot/dts/qcom-ipq8064-r7500.dts | 370 +++++++++++++++++++++++++++++++
+ 2 files changed, 371 insertions(+)
+ create mode 100644 arch/arm/boot/dts/qcom-ipq8064-r7500.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -506,7 +506,11 @@
+ qcom-apq8084-ifc6540.dtb \
+ qcom-apq8084-mtp.dtb \
+ qcom-ipq8064-ap148.dtb \
++ qcom-ipq8064-c2600.dtb \
++ qcom-ipq8064-d7800.dtb \
+ qcom-ipq8064-db149.dtb \
++ qcom-ipq8064-ea8500.dtb \
++ qcom-ipq8064-r7500.dtb \
+ qcom-msm8660-surf.dtb \
+ qcom-msm8960-cdp.dtb \
+ qcom-msm8974-sony-xperia-honami.dtb
+++ /dev/null
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -362,6 +362,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
- qcom-ipq8064-ap148.dtb \
- qcom-ipq8064-db149.dtb \
- qcom-ipq8064-r7500.dtb \
-+ qcom-ipq8064-d7800.dtb \
- qcom-msm8660-surf.dtb \
- qcom-msm8960-cdp.dtb \
- qcom-msm8974-sony-xperia-honami.dtb
---- /dev/null
-+++ b/arch/arm/boot/dts/qcom-ipq8064-d7800.dts
-@@ -0,0 +1,368 @@
-+#include "qcom-ipq8064-v1.0.dtsi"
-+
-+#include <dt-bindings/input/input.h>
-+
-+/ {
-+ model = "Netgear Nighthawk X4 D7800";
-+ compatible = "netgear,d7800", "qcom,ipq8064";
-+
-+ memory@0 {
-+ reg = <0x42000000 0xe000000>;
-+ device_type = "memory";
-+ };
-+
-+ reserved-memory {
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ ranges;
-+ rsvd@41200000 {
-+ reg = <0x41200000 0x300000>;
-+ no-map;
-+ };
-+ };
-+
-+ aliases {
-+ serial0 = &uart4;
-+ mdio-gpio0 = &mdio0;
-+ };
-+
-+ chosen {
-+ bootargs = "rootfstype=squashfs noinitrd";
-+ linux,stdout-path = "serial0:115200n8";
-+ };
-+
-+ soc {
-+ pinmux@800000 {
-+ i2c4_pins: i2c4_pinmux {
-+ pins = "gpio12", "gpio13";
-+ function = "gsbi4";
-+ bias-disable;
-+ };
-+
-+ pcie0_pins: pcie0_pinmux {
-+ mux {
-+ pins = "gpio3";
-+ function = "pcie1_rst";
-+ drive-strength = <12>;
-+ bias-disable;
-+ };
-+ };
-+
-+ pcie1_pins: pcie1_pinmux {
-+ mux {
-+ pins = "gpio48";
-+ function = "pcie2_rst";
-+ drive-strength = <12>;
-+ bias-disable;
-+ };
-+ };
-+
-+ nand_pins: nand_pins {
-+ mux {
-+ pins = "gpio34", "gpio35", "gpio36",
-+ "gpio37", "gpio38", "gpio39",
-+ "gpio40", "gpio41", "gpio42",
-+ "gpio43", "gpio44", "gpio45",
-+ "gpio46", "gpio47";
-+ function = "nand";
-+ drive-strength = <10>;
-+ bias-disable;
-+ };
-+ pullups {
-+ pins = "gpio39";
-+ bias-pull-up;
-+ };
-+ hold {
-+ pins = "gpio40", "gpio41", "gpio42",
-+ "gpio43", "gpio44", "gpio45",
-+ "gpio46", "gpio47";
-+ bias-bus-hold;
-+ };
-+ };
-+
-+ mdio0_pins: mdio0_pins {
-+ mux {
-+ pins = "gpio0", "gpio1";
-+ function = "gpio";
-+ drive-strength = <8>;
-+ bias-disable;
-+ };
-+ };
-+
-+ rgmii2_pins: rgmii2_pins {
-+ mux {
-+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
-+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
-+ function = "rgmii2";
-+ drive-strength = <8>;
-+ bias-disable;
-+ };
-+ };
-+ };
-+
-+ gsbi@16300000 {
-+ qcom,mode = <GSBI_PROT_I2C_UART>;
-+ status = "ok";
-+ serial@16340000 {
-+ status = "ok";
-+ };
-+ /*
-+ * The i2c device on gsbi4 should not be enabled.
-+ * On ipq806x designs gsbi4 i2c is meant for exclusive
-+ * RPM usage. Turning this on in kernel manifests as
-+ * i2c failure for the RPM.
-+ */
-+ };
-+
-+ sata-phy@1b400000 {
-+ status = "ok";
-+ };
-+
-+ sata@29000000 {
-+ status = "ok";
-+ };
-+
-+ phy@100f8800 { /* USB3 port 1 HS phy */
-+ status = "ok";
-+ };
-+
-+ phy@100f8830 { /* USB3 port 1 SS phy */
-+ status = "ok";
-+ };
-+
-+ phy@110f8800 { /* USB3 port 0 HS phy */
-+ status = "ok";
-+ };
-+
-+ phy@110f8830 { /* USB3 port 0 SS phy */
-+ status = "ok";
-+ };
-+
-+ usb30@0 {
-+ status = "ok";
-+ };
-+
-+ usb30@1 {
-+ status = "ok";
-+ };
-+
-+ pcie0: pci@1b500000 {
-+ status = "ok";
-+ reset-gpio = <&qcom_pinmux 3 0>;
-+ pinctrl-0 = <&pcie0_pins>;
-+ pinctrl-names = "default";
-+ };
-+
-+ pcie1: pci@1b700000 {
-+ status = "ok";
-+ reset-gpio = <&qcom_pinmux 48 0>;
-+ pinctrl-0 = <&pcie1_pins>;
-+ pinctrl-names = "default";
-+ };
-+
-+ nand@1ac00000 {
-+ status = "ok";
-+
-+ pinctrl-0 = <&nand_pins>;
-+ pinctrl-names = "default";
-+
-+ nand-ecc-strength = <4>;
-+ nand-bus-width = <8>;
-+
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+
-+ qcadata@0 {
-+ label = "qcadata";
-+ reg = <0x0000000 0x0c80000>;
-+ read-only;
-+ };
-+
-+ APPSBL@c80000 {
-+ label = "APPSBL";
-+ reg = <0x0c80000 0x0500000>;
-+ read-only;
-+ };
-+
-+ APPSBLENV@1180000 {
-+ label = "APPSBLENV";
-+ reg = <0x1180000 0x0080000>;
-+ read-only;
-+ };
-+
-+ art: art@1200000 {
-+ label = "art";
-+ reg = <0x1200000 0x0140000>;
-+ read-only;
-+ };
-+
-+ artbak: art@1340000 {
-+ label = "artbak";
-+ reg = <0x1340000 0x0140000>;
-+ read-only;
-+ };
-+
-+ kernel@1480000 {
-+ label = "kernel";
-+ reg = <0x1480000 0x0200000>;
-+ };
-+
-+ ubi@1680000 {
-+ label = "ubi";
-+ reg = <0x1680000 0x1E00000>;
-+ };
-+
-+ netgear@3480000 {
-+ label = "netgear";
-+ reg = <0x3480000 0x4480000>;
-+ read-only;
-+ };
-+
-+ reserve@7900000 {
-+ label = "reserve";
-+ reg = <0x7900000 0x0700000>;
-+ read-only;
-+ };
-+
-+ firmware@1480000 {
-+ label = "firmware";
-+ reg = <0x1480000 0x2000000>;
-+ };
-+
-+ };
-+
-+ mdio0: mdio {
-+ compatible = "virtual,mdio-gpio";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
-+ pinctrl-0 = <&mdio0_pins>;
-+ pinctrl-names = "default";
-+
-+ phy0: ethernet-phy@0 {
-+ device_type = "ethernet-phy";
-+ reg = <0>;
-+ qca,ar8327-initvals = <
-+ 0x00004 0x7600000 /* PAD0_MODE */
-+ 0x00008 0x1000000 /* PAD5_MODE */
-+ 0x0000c 0x80 /* PAD6_MODE */
-+ 0x000e4 0xaa545 /* MAC_POWER_SEL */
-+ 0x000e0 0xc74164de /* SGMII_CTRL */
-+ 0x0007c 0x4e /* PORT0_STATUS */
-+ 0x00094 0x4e /* PORT6_STATUS */
-+ >;
-+ };
-+
-+ phy4: ethernet-phy@4 {
-+ device_type = "ethernet-phy";
-+ reg = <4>;
-+ };
-+ };
-+
-+ gmac1: ethernet@37200000 {
-+ status = "ok";
-+ phy-mode = "rgmii";
-+ phy-handle = <&phy4>;
-+ qcom,id = <1>;
-+
-+ pinctrl-0 = <&rgmii2_pins>;
-+ pinctrl-names = "default";
-+
-+ mtd-mac-address = <&art 6>;
-+ };
-+
-+ gmac2: ethernet@37400000 {
-+ status = "ok";
-+ phy-mode = "sgmii";
-+ qcom,id = <2>;
-+
-+ mtd-mac-address = <&art 0>;
-+
-+ fixed-link {
-+ speed = <1000>;
-+ full-duplex;
-+ };
-+ };
-+ };
-+
-+ gpio-keys {
-+ compatible = "gpio-keys";
-+
-+ wifi {
-+ label = "wifi";
-+ gpios = <&qcom_pinmux 6 1>;
-+ linux,code = <KEY_WLAN>;
-+ };
-+
-+ reset {
-+ label = "reset";
-+ gpios = <&qcom_pinmux 54 1>;
-+ linux,code = <KEY_RESTART>;
-+ };
-+
-+ wps {
-+ label = "wps";
-+ gpios = <&qcom_pinmux 65 1>;
-+ linux,code = <KEY_WPS_BUTTON>;
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+
-+ usb1 {
-+ label = "d7800:amber:usb1";
-+ gpios = <&qcom_pinmux 7 0>;
-+ };
-+
-+ usb3 {
-+ label = "d7800:amber:usb3";
-+ gpios = <&qcom_pinmux 8 0>;
-+ };
-+
-+ status {
-+ label = "d7800:amber:status";
-+ gpios = <&qcom_pinmux 9 0>;
-+ };
-+
-+ internet {
-+ label = "d7800:white:internet";
-+ gpios = <&qcom_pinmux 22 0>;
-+ };
-+
-+ wan {
-+ label = "d7800:white:wan";
-+ gpios = <&qcom_pinmux 23 0>;
-+ };
-+
-+ wps {
-+ label = "d7800:white:wps";
-+ gpios = <&qcom_pinmux 24 0>;
-+ };
-+
-+ esata {
-+ label = "d7800:white:esata";
-+ gpios = <&qcom_pinmux 26 0>;
-+ };
-+
-+ power {
-+ label = "d7800:white:power";
-+ gpios = <&qcom_pinmux 53 0>;
-+ default-state = "on";
-+ };
-+
-+ rfkill {
-+ label = "d7800:white:rfkill";
-+ gpios = <&qcom_pinmux 64 0>;
-+ };
-+
-+ wifi5g {
-+ label = "d7800:white:wifi5g";
-+ gpios = <&qcom_pinmux 67 0>;
-+ };
-+ };
-+};
-+
-+&adm_dma {
-+ status = "ok";
-+};
+++ /dev/null
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -506,6 +506,7 @@
- qcom-apq8084-ifc6540.dtb \
- qcom-apq8084-mtp.dtb \
- qcom-ipq8064-ap148.dtb \
-+ qcom-ipq8064-c2600.dtb \
- qcom-ipq8064-db149.dtb \
- qcom-ipq8064-r7500.dtb \
- qcom-ipq8064-d7800.dtb \
---- /dev/null
-+++ b/arch/arm/boot/dts/qcom-ipq8064-c2600.dts
-@@ -0,0 +1,412 @@
-+#include "qcom-ipq8064-v1.0.dtsi"
-+#include <dt-bindings/input/input.h>
-+
-+/ {
-+ model = "TP-Link Archer C2600";
-+ compatible = "tplink,c2600", "qcom,ipq8064";
-+
-+ memory@0 {
-+ reg = <0x42000000 0x1e000000>;
-+ device_type = "memory";
-+ };
-+
-+ reserved-memory {
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ ranges;
-+ rsvd@41200000 {
-+ reg = <0x41200000 0x300000>;
-+ no-map;
-+ };
-+ };
-+
-+ aliases {
-+ serial0 = &uart4;
-+ mdio-gpio0 = &mdio0;
-+ };
-+
-+ chosen {
-+ linux,stdout-path = "serial0:115200n8";
-+ };
-+
-+ soc {
-+ pinmux@800000 {
-+ i2c4_pins: i2c4_pinmux {
-+ pins = "gpio12", "gpio13";
-+ function = "gsbi4";
-+ bias-disable;
-+ };
-+
-+ spi_pins: spi_pins {
-+ mux {
-+ pins = "gpio18", "gpio19", "gpio21";
-+ function = "gsbi5";
-+ drive-strength = <10>;
-+ bias-none;
-+ };
-+ };
-+
-+ nand_pins: nand_pins {
-+ mux {
-+ pins = "gpio34", "gpio35", "gpio36",
-+ "gpio37", "gpio38", "gpio39",
-+ "gpio40", "gpio41", "gpio42",
-+ "gpio43", "gpio44", "gpio45",
-+ "gpio46", "gpio47";
-+ function = "nand";
-+ drive-strength = <10>;
-+ bias-disable;
-+ };
-+
-+ pullups {
-+ pins = "gpio39";
-+ bias-pull-up;
-+ };
-+
-+ hold {
-+ pins = "gpio40", "gpio41", "gpio42",
-+ "gpio43", "gpio44", "gpio45",
-+ "gpio46", "gpio47";
-+ bias-bus-hold;
-+ };
-+ };
-+
-+ mdio0_pins: mdio0_pins {
-+ mux {
-+ pins = "gpio0", "gpio1";
-+ function = "gpio";
-+ drive-strength = <8>;
-+ bias-disable;
-+ };
-+ };
-+
-+ rgmii2_pins: rgmii2_pins {
-+ mux {
-+ pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
-+ "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
-+ function = "rgmii2";
-+ drive-strength = <8>;
-+ bias-disable;
-+ };
-+ };
-+ };
-+
-+ gsbi@16300000 {
-+ qcom,mode = <GSBI_PROT_I2C_UART>;
-+ status = "ok";
-+ serial@16340000 {
-+ status = "ok";
-+ };
-+ /*
-+ * The i2c device on gsbi4 should not be enabled.
-+ * On ipq806x designs gsbi4 i2c is meant for exclusive
-+ * RPM usage. Turning this on in kernel manifests as
-+ * i2c failure for the RPM.
-+ */
-+ };
-+
-+ gsbi5: gsbi@1a200000 {
-+ qcom,mode = <GSBI_PROT_SPI>;
-+ status = "ok";
-+
-+ spi4: spi@1a280000 {
-+ status = "ok";
-+ spi-max-frequency = <50000000>;
-+
-+ pinctrl-0 = <&spi_pins>;
-+ pinctrl-names = "default";
-+
-+ cs-gpios = <&qcom_pinmux 20 0>;
-+
-+ flash: m25p80@0 {
-+ compatible = "s25fl256s1";
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ spi-max-frequency = <50000000>;
-+ reg = <0>;
-+
-+ SBL1@0 {
-+ label = "SBL1";
-+ reg = <0x0 0x20000>;
-+ read-only;
-+ };
-+ MIBIB@20000 {
-+ label = "MIBIB";
-+ reg = <0x20000 0x20000>;
-+ read-only;
-+ };
-+ SBL2@40000 {
-+ label = "SBL2";
-+ reg = <0x40000 0x20000>;
-+ read-only;
-+ };
-+ SBL3@60000 {
-+ label = "SBL3";
-+ reg = <0x60000 0x30000>;
-+ read-only;
-+ };
-+ DDRCONFIG@90000 {
-+ label = "DDRCONFIG";
-+ reg = <0x90000 0x10000>;
-+ read-only;
-+ };
-+ SSD@a0000 {
-+ label = "SSD";
-+ reg = <0xa0000 0x10000>;
-+ read-only;
-+ };
-+ TZ@b0000 {
-+ label = "TZ";
-+ reg = <0xb0000 0x30000>;
-+ read-only;
-+ };
-+ RPM@e0000 {
-+ label = "RPM";
-+ reg = <0xe0000 0x20000>;
-+ read-only;
-+ };
-+ fs-uboot@100000 {
-+ label = "fs-uboot";
-+ reg = <0x100000 0x70000>;
-+ read-only;
-+ };
-+ uboot-env@170000 {
-+ label = "uboot-env";
-+ reg = <0x170000 0x40000>;
-+ read-only;
-+ };
-+ radio@1b0000 {
-+ label = "radio";
-+ reg = <0x1b0000 0x40000>;
-+ read-only;
-+ };
-+ os-image@1f0000 {
-+ label = "os-image";
-+ reg = <0x1f0000 0x200000>;
-+ };
-+ rootfs@3f0000 {
-+ label = "rootfs";
-+ reg = <0x3f0000 0x1b00000>;
-+ };
-+ defaultmac: default-mac@1ef0000 {
-+ label = "default-mac";
-+ reg = <0x1ef0000 0x00200>;
-+ read-only;
-+ };
-+ pin@1ef0200 {
-+ label = "pin";
-+ reg = <0x1ef0200 0x00200>;
-+ read-only;
-+ };
-+ product-info@1ef0400 {
-+ label = "product-info";
-+ reg = <0x1ef0400 0x0fc00>;
-+ read-only;
-+ };
-+ partition-table@1f00000 {
-+ label = "partition-table";
-+ reg = <0x1f00000 0x10000>;
-+ read-only;
-+ };
-+ soft-version@1f10000 {
-+ label = "soft-version";
-+ reg = <0x1f10000 0x10000>;
-+ read-only;
-+ };
-+ support-list@1f20000 {
-+ label = "support-list";
-+ reg = <0x1f20000 0x10000>;
-+ read-only;
-+ };
-+ profile@1f30000 {
-+ label = "profile";
-+ reg = <0x1f30000 0x10000>;
-+ read-only;
-+ };
-+ default-config@1f40000 {
-+ label = "default-config";
-+ reg = <0x1f40000 0x10000>;
-+ read-only;
-+ };
-+ user-config@1f50000 {
-+ label = "user-config";
-+ reg = <0x1f50000 0x40000>;
-+ read-only;
-+ };
-+ qos-db@1f90000 {
-+ label = "qos-db";
-+ reg = <0x1f90000 0x40000>;
-+ read-only;
-+ };
-+ usb-config@1fd0000 {
-+ label = "usb-config";
-+ reg = <0x1fd0000 0x10000>;
-+ read-only;
-+ };
-+ log@1fe0000 {
-+ label = "log";
-+ reg = <0x1fe0000 0x20000>;
-+ read-only;
-+ };
-+ };
-+ };
-+ };
-+
-+ phy@100f8800 { /* USB3 port 1 HS phy */
-+ status = "ok";
-+ };
-+
-+ phy@100f8830 { /* USB3 port 1 SS phy */
-+ status = "ok";
-+ };
-+
-+ phy@110f8800 { /* USB3 port 0 HS phy */
-+ status = "ok";
-+ };
-+
-+ phy@110f8830 { /* USB3 port 0 SS phy */
-+ status = "ok";
-+ };
-+
-+ usb30@0 {
-+ status = "ok";
-+ };
-+
-+ usb30@1 {
-+ status = "ok";
-+ };
-+
-+ pcie0: pci@1b500000 {
-+ status = "ok";
-+ phy-tx0-term-offset = <7>;
-+ };
-+
-+ pcie1: pci@1b700000 {
-+ status = "ok";
-+ phy-tx0-term-offset = <7>;
-+ };
-+
-+ mdio0: mdio {
-+ compatible = "virtual,mdio-gpio";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>;
-+ pinctrl-0 = <&mdio0_pins>;
-+ pinctrl-names = "default";
-+
-+ phy0: ethernet-phy@0 {
-+ device_type = "ethernet-phy";
-+ reg = <0>;
-+ qca,ar8327-initvals = <
-+ 0x00004 0x7600000 /* PAD0_MODE */
-+ 0x00008 0x1000000 /* PAD5_MODE */
-+ 0x0000c 0x80 /* PAD6_MODE */
-+ 0x000e4 0xaa545 /* MAC_POWER_SEL */
-+ 0x000e0 0xc74164de /* SGMII_CTRL */
-+ 0x0007c 0x4e /* PORT0_STATUS */
-+ 0x00094 0x4e /* PORT6_STATUS */
-+ >;
-+ };
-+
-+ phy4: ethernet-phy@4 {
-+ device_type = "ethernet-phy";
-+ reg = <4>;
-+ };
-+ };
-+
-+ gmac1: ethernet@37200000 {
-+ status = "ok";
-+ phy-mode = "rgmii";
-+ qcom,id = <1>;
-+
-+ pinctrl-0 = <&rgmii2_pins>;
-+ pinctrl-names = "default";
-+
-+ mtd-mac-address = <&defaultmac 0x8>;
-+ mtd-mac-address-increment = <1>;
-+
-+ fixed-link {
-+ speed = <1000>;
-+ full-duplex;
-+ };
-+ };
-+
-+ gmac2: ethernet@37400000 {
-+ status = "ok";
-+ phy-mode = "sgmii";
-+ qcom,id = <2>;
-+
-+ mtd-mac-address = <&defaultmac 0x8>;
-+
-+ fixed-link {
-+ speed = <1000>;
-+ full-duplex;
-+ };
-+ };
-+ };
-+
-+ gpio-keys {
-+ compatible = "gpio-keys";
-+
-+ wifi {
-+ label = "wifi";
-+ gpios = <&qcom_pinmux 49 1>;
-+ linux,code = <KEY_WLAN>;
-+ };
-+
-+ reset {
-+ label = "reset";
-+ gpios = <&qcom_pinmux 64 1>;
-+ linux,code = <KEY_RESTART>;
-+ };
-+
-+ wps {
-+ label = "wps";
-+ gpios = <&qcom_pinmux 65 1>;
-+ linux,code = <KEY_WPS_BUTTON>;
-+ };
-+ ledgeneral {
-+ label = "ledgeneral";
-+ gpios = <&qcom_pinmux 16 1>;
-+ linux,code = <KEY_DOLLAR>;
-+ };
-+ };
-+
-+ gpio-leds {
-+ compatible = "gpio-leds";
-+
-+ lan {
-+ label = "lan:blue";
-+ gpios = <&qcom_pinmux 6 0>;
-+ };
-+ usb4 {
-+ label = "usb_4:blue";
-+ gpios = <&qcom_pinmux 7 0>;
-+ };
-+ usb2 {
-+ label = "usb_2:blue";
-+ gpios = <&qcom_pinmux 8 0>;
-+ };
-+ wps {
-+ label = "wps:blue";
-+ gpios = <&qcom_pinmux 9 0>;
-+ };
-+ wan_blue {
-+ label = "wan:blue";
-+ gpios = <&qcom_pinmux 33 1>;
-+ };
-+ status {
-+ label = "status:blue";
-+ gpios = <&qcom_pinmux 53 0>;
-+ default-state = "on";
-+ };
-+ ledgnr {
-+ label = "ledgnr:blue";
-+ gpios = <&qcom_pinmux 66 0>;
-+ };
-+ };
-+};
-+
-+&adm_dma {
-+ status = "ok";
-+};
projects / openwrt / staging / jogo.git / commitdiff