From: Óscar García Amor Date: Tue, 20 Sep 2022 11:24:43 +0000 (+0200) Subject: ramips: add support for Cudy WR1300 v2 X-Git-Url: http://git.openwrt.org/?a=commitdiff_plain;h=62efb34071cff2e15bff85b00040520dad7d6097;hp=18801f26485e3a0dcb79dc9f9b174aed5821b758;p=openwrt%2Fstaging%2Fstintel.git ramips: add support for Cudy WR1300 v2 Specifications: - SoC: MediaTek MT7621AT - RAM: 128 MB (DDR3) - Flash: 16 MB (SPI NOR) - WiFi: MediaTek MT7603E, MediaTek MT7613BE - Switch: 1 WAN, 4 LAN (Gigabit) - Ports: 1 USB 3.0 - Buttons: Reset, WPS - LEDs: System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS - Power: DC 12V 1A tip positive Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: - Loads only signed manufacture firmware due to bootloader RSA verification - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 - connect to any lan ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button for image to download - See http://www.cudytech.com/newsinfo/547425.html Signed-off-by: Óscar García Amor --- diff --git a/target/linux/ramips/dts/mt7621_cudy_wr1300-v1.dts b/target/linux/ramips/dts/mt7621_cudy_wr1300-v1.dts new file mode 100644 index 0000000000..4062c46e3e --- /dev/null +++ b/target/linux/ramips/dts/mt7621_cudy_wr1300-v1.dts @@ -0,0 +1,217 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include + +/ { + compatible = "cudy,wr1300-v1", "mediatek,mt7621-soc"; + model = "Cudy WR1300 v1"; + + aliases { + led-boot = &led_sys; + led-failsafe = &led_sys; + led-running = &led_sys; + led-upgrade = &led_sys; + label-mac-device = &gmac0; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_sys: sys { + label = "green:sys"; + gpios = <&gpio 15 GPIO_ACTIVE_HIGH>; + }; + + usb { + label = "green:usb"; + gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; + trigger-sources = <&xhci_ehci_port1>, <&ehci_port2>; + linux,default-trigger = "usbport"; + }; + + wps { + label = "green:wps"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <80000000>; + m25p,fast-read; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x50000 0xf80000>; + }; + + partition@fd0000 { + label = "debug"; + reg = <0xfd0000 0x10000>; + read-only; + }; + + partition@fe0000 { + label = "backup"; + reg = <0xfe0000 0x10000>; + read-only; + }; + + bdinfo: partition@ff0000 { + label = "bdinfo"; + reg = <0xff0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + compatible = "pci14c3,7603"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0000>; + nvmem-cells = <&macaddr_bdinfo_de00>; + nvmem-cell-names = "mac-address"; + ieee80211-freq-limit = <2400000 2500000>; + + led { + led-active-low; + }; + }; +}; + +&pcie1 { + wifi@0,0 { + compatible = "pci14c3,7662"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x8000>; + nvmem-cells = <&macaddr_bdinfo_de00>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <2>; + ieee80211-freq-limit = <5000000 6000000>; + + led { + led-sources = <2>; + led-active-low; + }; + }; +}; + +&gmac0 { + nvmem-cells = <&macaddr_bdinfo_de00>; + nvmem-cell-names = "mac-address"; +}; + +&gmac1 { + status = "okay"; + label = "wan"; + phy-handle = <ðphy4>; + + nvmem-cells = <&macaddr_bdinfo_de00>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <1>; +}; + +&mdio { + ethphy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "lan4"; + }; + + port@1 { + status = "okay"; + label = "lan3"; + }; + + port@2 { + status = "okay"; + label = "lan2"; + }; + + port@3 { + status = "okay"; + label = "lan1"; + }; + }; +}; + +&state_default { + gpio { + groups = "wdt", "i2c", "jtag"; + function = "gpio"; + }; +}; + +&bdinfo { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_bdinfo_de00: macaddr@de00 { + reg = <0xde00 0x6>; + }; +}; diff --git a/target/linux/ramips/dts/mt7621_cudy_wr1300-v2.dts b/target/linux/ramips/dts/mt7621_cudy_wr1300-v2.dts new file mode 100644 index 0000000000..5c8b047e76 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_cudy_wr1300-v2.dts @@ -0,0 +1,199 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include + +/ { + compatible = "cudy,wr1300-v2", "mediatek,mt7621-soc"; + model = "Cudy WR1300 v2"; + + aliases { + led-boot = &led_sys; + led-failsafe = &led_sys; + led-running = &led_sys; + led-upgrade = &led_sys; + label-mac-device = &gmac0; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_sys: sys { + label = "green:sys"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "green:wps"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <80000000>; + m25p,fast-read; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x50000 0xf80000>; + }; + + partition@fd0000 { + label = "debug"; + reg = <0xfd0000 0x10000>; + read-only; + }; + + partition@fe0000 { + label = "backup"; + reg = <0xfe0000 0x10000>; + read-only; + }; + + bdinfo: partition@ff0000 { + label = "bdinfo"; + reg = <0xff0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie1 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0000>; + nvmem-cells = <&macaddr_bdinfo_de00>; + nvmem-cell-names = "mac-address"; + }; +}; + +&pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x8000>; + nvmem-cells = <&macaddr_bdinfo_de00>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <2>; + }; +}; + +&gmac0 { + nvmem-cells = <&macaddr_bdinfo_de00>; + nvmem-cell-names = "mac-address"; +}; + +&gmac1 { + status = "okay"; + label = "wan"; + phy-handle = <ðphy4>; + + nvmem-cells = <&macaddr_bdinfo_de00>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <1>; +}; + +&mdio { + ethphy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "lan4"; + }; + + port@1 { + status = "okay"; + label = "lan3"; + }; + + port@2 { + status = "okay"; + label = "lan2"; + }; + + port@3 { + status = "okay"; + label = "lan1"; + }; + }; +}; + +&state_default { + gpio { + groups = "wdt", "i2c", "jtag"; + function = "gpio"; + }; +}; + +&bdinfo { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_bdinfo_de00: macaddr@de00 { + reg = <0xde00 0x6>; + }; +}; diff --git a/target/linux/ramips/dts/mt7621_cudy_wr1300.dts b/target/linux/ramips/dts/mt7621_cudy_wr1300.dts deleted file mode 100644 index 2398612847..0000000000 --- a/target/linux/ramips/dts/mt7621_cudy_wr1300.dts +++ /dev/null @@ -1,217 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0-or-later OR MIT - -#include "mt7621.dtsi" - -#include -#include - -/ { - compatible = "cudy,wr1300", "mediatek,mt7621-soc"; - model = "Cudy WR1300"; - - aliases { - led-boot = &led_sys; - led-failsafe = &led_sys; - led-running = &led_sys; - led-upgrade = &led_sys; - label-mac-device = &gmac0; - }; - - chosen { - bootargs = "console=ttyS0,115200"; - }; - - keys { - compatible = "gpio-keys"; - - reset { - label = "reset"; - gpios = <&gpio 18 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - - wps { - label = "wps"; - gpios = <&gpio 3 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - leds { - compatible = "gpio-leds"; - - led_sys: sys { - label = "green:sys"; - gpios = <&gpio 15 GPIO_ACTIVE_HIGH>; - }; - - usb { - label = "green:usb"; - gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; - trigger-sources = <&xhci_ehci_port1>, <&ehci_port2>; - linux,default-trigger = "usbport"; - }; - - wps { - label = "green:wps"; - gpios = <&gpio 13 GPIO_ACTIVE_LOW>; - }; - }; -}; - -&spi0 { - status = "okay"; - - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <80000000>; - m25p,fast-read; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x0 0x30000>; - read-only; - }; - - partition@30000 { - label = "u-boot-env"; - reg = <0x30000 0x10000>; - read-only; - }; - - factory: partition@40000 { - label = "factory"; - reg = <0x40000 0x10000>; - read-only; - }; - - partition@50000 { - compatible = "denx,uimage"; - label = "firmware"; - reg = <0x50000 0xf80000>; - }; - - partition@fd0000 { - label = "debug"; - reg = <0xfd0000 0x10000>; - read-only; - }; - - partition@fe0000 { - label = "backup"; - reg = <0xfe0000 0x10000>; - read-only; - }; - - bdinfo: partition@ff0000 { - label = "bdinfo"; - reg = <0xff0000 0x10000>; - read-only; - }; - }; - }; -}; - -&pcie { - status = "okay"; -}; - -&pcie0 { - wifi@0,0 { - compatible = "pci14c3,7603"; - reg = <0x0000 0 0 0 0>; - mediatek,mtd-eeprom = <&factory 0x0000>; - nvmem-cells = <&macaddr_bdinfo_de00>; - nvmem-cell-names = "mac-address"; - ieee80211-freq-limit = <2400000 2500000>; - - led { - led-active-low; - }; - }; -}; - -&pcie1 { - wifi@0,0 { - compatible = "pci14c3,7662"; - reg = <0x0000 0 0 0 0>; - mediatek,mtd-eeprom = <&factory 0x8000>; - nvmem-cells = <&macaddr_bdinfo_de00>; - nvmem-cell-names = "mac-address"; - mac-address-increment = <2>; - ieee80211-freq-limit = <5000000 6000000>; - - led { - led-sources = <2>; - led-active-low; - }; - }; -}; - -&gmac0 { - nvmem-cells = <&macaddr_bdinfo_de00>; - nvmem-cell-names = "mac-address"; -}; - -&gmac1 { - status = "okay"; - label = "wan"; - phy-handle = <ðphy4>; - - nvmem-cells = <&macaddr_bdinfo_de00>; - nvmem-cell-names = "mac-address"; - mac-address-increment = <1>; -}; - -&mdio { - ethphy4: ethernet-phy@4 { - reg = <4>; - }; -}; - -&switch0 { - ports { - port@0 { - status = "okay"; - label = "lan4"; - }; - - port@1 { - status = "okay"; - label = "lan3"; - }; - - port@2 { - status = "okay"; - label = "lan2"; - }; - - port@3 { - status = "okay"; - label = "lan1"; - }; - }; -}; - -&state_default { - gpio { - groups = "wdt", "i2c", "jtag"; - function = "gpio"; - }; -}; - -&bdinfo { - compatible = "nvmem-cells"; - #address-cells = <1>; - #size-cells = <1>; - - macaddr_bdinfo_de00: macaddr@de00 { - reg = <0xde00 0x6>; - }; -}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index 2e7d0689be..de10da7cb6 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -444,15 +444,28 @@ define Device/bolt_arion endef TARGET_DEVICES += bolt_arion -define Device/cudy_wr1300 +define Device/cudy_wr1300-v1 $(Device/dsa-migration) IMAGE_SIZE := 15872k DEVICE_VENDOR := Cudy DEVICE_MODEL := WR1300 + DEVICE_VARIANT := v1 DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb2 kmod-usb3 \ kmod-usb-ledtrig-usbport + SUPPORTED_DEVICES += cudy,wr1300 R10 +endef +TARGET_DEVICES += cudy_wr1300-v1 + +define Device/cudy_wr1300-v2 + $(Device/dsa-migration) + IMAGE_SIZE := 15872k + DEVICE_VENDOR := Cudy + DEVICE_MODEL := WR1300 + DEVICE_VARIANT := v2 + DEVICE_PACKAGES := kmod-mt7603 kmod-mt7615e kmod-mt7663-firmware-ap + SUPPORTED_DEVICES += cudy,wr1300 R23 endef -TARGET_DEVICES += cudy_wr1300 +TARGET_DEVICES += cudy_wr1300-v2 define Device/cudy_wr2100 $(Device/dsa-migration)