Petr Štetiar [Fri, 4 Jan 2019 14:57:07 +0000 (15:57 +0100)]
ath79: ag71xx: Enable tx hang workaround for the rest of ar724x SoCs
In ar71xx we check for stuck DMA on devices which fall in the is_ar724x
SoC group (ar724x, ar933x, ar934x, qca9533, tp9343, qca955x, qca956x).
In ath79 we're currently performing this check only for devices with
ar7240 SoC, so this patch tries to sync the dma stuck checking behavior
with what is being done in ar71xx.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Wed, 3 Apr 2019 08:05:26 +0000 (10:05 +0200)]
ar71xx: ag71xx: Fix broken networking on some devices (FS#2177)
It was reported, that latest ar71xx builds have broken networking on
TP-Link TL-WPA8630 and Nanostation M5 XW devices and that by reverting
the offending commit, everything is back to normal.
Fixes: d3506d1 ("ar71xx: ag71xx: fix compile error when enabling debug")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Sat, 17 Nov 2018 07:01:55 +0000 (08:01 +0100)]
ar71xx: Add support for Ubiquity Bullet M (XW)
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART: 1 UART on PCB marked as J1 with 115200 8N1 config
LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
UART connection details
.---------------------------------.
| |
[ETH] J1 [ANT]
| o VCC o RX o TX o GND |
`---------------------------------'
Flashing instructions using recovery method over TFTP
1. Unplug the ethernet cable from the router.
2. Using paper clip press and hold the router's reset button. Make sure
you can feel it depressed by the paper clip. Do not release the button
until step 4.
3. While keeping the reset button pressed in, plug the ethernet cable
back into the AP. Keep the reset button depressed until you see the
device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
LED2/LED4), this may take up to 25 seconds.
4. You may release the reset button, now the device should be in TFTP
transfer mode.
5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
should work.
6. Plug the PoE injector's LAN cable directly to your computer.
7. Start tftp client and issue following commands:
tftp> binary
tftp> connect 192.168.1.20
tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin
Tested only on Bullet M2HP.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 19 Nov 2018 20:44:50 +0000 (21:44 +0100)]
ar71xx: ubnt-m-xw: Fix factory image flashing using TFTP recovery
This is backport of the same functionality in ath79, from commit
d42a7c469 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP
recovery method")
Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:
All future airOS versions will be signed in this way and not allow
unsigned firmware to be loaded except via TFTP.
U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:
Hit any key to stop autoboot: 0
Setting default IP 192.168.1.20
Starting TFTP server...
Receiving file from 192.168.1.25:38438
Received
4981148 bytes
Firmware check failed! (1)
By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:
Received
3801500 bytes
Firmware Version: XW.ar934x.v6.0.4-42.OpenWrt-r9766+2-
be42e44
Setting U-Boot environment variables
Un-Protected 1 sectors
Erasing Flash.... done
Patch provided by AREDN[3] project, tested on Bullet M2 XW.
1. https://help.ubnt.com/hc/en-us/articles/
204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Fri, 23 Nov 2018 09:33:24 +0000 (10:33 +0100)]
imx6: Add support for Toradex Apalis family of CoMs
This patch adds support for the following computer on modules (CoM) from
Toradex[A]:
Apalis iMX6 Quad 2GB IT - i.MX 6Quad 800MHz, 2GB DDR3, 4GB eMMC
-40° to +85° C Temp
Apalis iMX6 Quad 1GB - i.MX 6Quad 1GHz, 1GB DDR3, 4GB eMMC
0° to +70° C Temp
Apalis iMX6 Dual 1GB IT - i.MX 6Dual 800MHz, 1GB DDR3, 4GB eMMC
-40° to +85° C Temp
Apalis iMX6 Dual 512MB - i.MX 6Dual 1GHz, 512MB DDR3, 4GB eMMC
0° to +70° C Temp
I've developed and tested it on Quad 2GB IT v1.1A and Dual 512MB v1.1A
CoMs, using Ixora[B] carrier board v1.0A, but it should hopefuly work on
Eval[C] board as well.
A. https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-freescale-imx-6
B. https://www.toradex.com/products/carrier-board/ixora-carrier-board
C. https://www.toradex.com/products/carrier-board/apalis-evaluation-board
Flashing/recovery instructions:
1. Download and compile imx_loader for OpenWrt from
https://github.com/ynezz/imx_loader
2. Enter recovery mode as desribed in
https://developer.toradex.com/knowledge-base/imx-recovery-mode
3. Connect board via USB to the host computer, check that it's connected
by lsusb:
15a2:0054 Freescale Semiconductor, Inc. i.MX 6Dual/6Quad SystemOnChip
in RecoveryMode
4. Copy following OpenWrt images to imx_loader directory:
SPL
u-boot.img
u-boot-with-spl.imx
openwrt-imx6-apalis-recovery.scr
openwrt-imx6-apalis-squashfs.combined.bin
5. Run imx_usb in imx_loader directory
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Fri, 23 Nov 2018 08:25:13 +0000 (09:25 +0100)]
imx6: image: Split imx6-sdcard image for reusability
I'm going to reuse the imx6-sdcard image commands for building of Apalis
eMMC images.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Tue, 27 Nov 2018 20:22:41 +0000 (21:22 +0100)]
uboot-envtools: imx6: Add support for Toradex Apalis board family
This patch is needed in order to be able to use fw_{set,print}env
commands.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 26 Nov 2018 22:31:53 +0000 (23:31 +0100)]
uboot-imx6: Add support for Toradex Apalis board family
This patch is needed in order to properly boot OpenWrt bootscript.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hans Dedecker [Mon, 8 Apr 2019 07:53:25 +0000 (09:53 +0200)]
glibc: update to latest 2.27 commit [BZ #22964]
de9d4aa353 ja_JP locale: Add entry for the new Japanese era [BZ #22964]
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Koen Vandeputte [Mon, 8 Apr 2019 12:15:26 +0000 (14:15 +0200)]
kernel: bump 4.19 to 4.19.34
Refreshed all patches.
Removed:
- 030-PCI-dwc-skip-MSI-init-if-MSIs-have-been-explicitly-d.patch
Altered:
- 366-netfilter-nf_flow_table-clean-up-and-fix-dst-handlin.patch
- 650-netfilter-add-xt_OFFLOAD-target.patch
- 662-remove_pfifo_fast.patch
- 332-arc-add-OWRTDTB-section.patch
- 100-clocksource-drivers-arch_timer-Workaround-for-Allwin.patch
- 702-phy_add_aneg_done_function.patch
New symbols:
- ARC_IRQ_NO_AUTOSAVE
- SUN50I_ERRATUM_UNKNOWN1
Compile-tested: cns3xxx, imx6, sunxi
Runtime-tested: cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 8 Apr 2019 11:39:00 +0000 (13:39 +0200)]
kernel: bump 4.14 to 4.14.111
Refreshed all patches.
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 8 Apr 2019 11:37:02 +0000 (13:37 +0200)]
kernel: bump 4.9 to 4.9.168
Refreshed all patches.
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Fri, 5 Apr 2019 08:58:45 +0000 (10:58 +0200)]
kernel: bump 4.14 to 4.14.110
Refreshed all patches.
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Fri, 5 Apr 2019 08:55:56 +0000 (10:55 +0200)]
kernel: bump 4.9 to 4.9.167
Refreshed all patches.
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Hans Dedecker [Sun, 7 Apr 2019 18:22:19 +0000 (20:22 +0200)]
dropbear: bump to 2019.78
Fix dbclient regression in 2019.77. After exiting the terminal would be left
in a bad state. Reported by Ryan Woodsmall
drop patch applied upstream:
010-tty-modes-werent-reset-for-client.patch
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Stijn Tintel [Sun, 7 Apr 2019 16:36:30 +0000 (19:36 +0300)]
ubox: bump to git HEAD
5130fa4 kmodloader: fix and optimize loading of failed modules
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Tomasz Maciej Nowak [Sun, 7 Apr 2019 13:15:36 +0000 (15:15 +0200)]
tools: cbootimage: depend on automake
Fix missing aclocal reported by buildbot.
Fixes: 8595bb0 ("tools: add cbootimage for tegra")
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Christian Lamparter [Sat, 6 Apr 2019 18:29:35 +0000 (20:29 +0200)]
firmware-utils: fix nec-enc build on older architectures
This patch enable gnu99 mode for the nec-enc utility which
fixes the following build-breaking errors on some older
architectures.
nec-enc.c: In function ‘xor_data’:
nec-enc.c:34:2: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode
for (int i = 0; i < len; i++) {
^~~
nec-enc.c:34:2: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 to compile your code
nec-enc.c: In function ‘main’:
nec-enc.c:101:3: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode
for (int i = 0; i < n; i++) {
^~~
Spotted-By: Buildbot
Fixes: fac27643f057 ("firmware-utils: add nec-enc")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Kip Porterfield [Fri, 5 Apr 2019 23:46:33 +0000 (19:46 -0400)]
ramips: correct DTS for Belkin F9K1109v1 to include switch definition
Add switch definition for the rtl8367b switch to the DTS/DTSi for
the Belkin F9K1109v1 that was mistakenly omitted from the initial
commit.
Fixes: 017ec068e3df (ramips: add support for Belkin F9K1109v1)
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
INAGAKI Hiroshi [Sat, 16 Mar 2019 04:27:32 +0000 (13:27 +0900)]
ath79: add support for NEC Aterm WG1200CR
NEC Aterm WG1200CR is a 2.4/5 GHz band 11ac router,
based on Qualcomm Atheros QCA9563.
Specification:
- SoC : Qualcomm Atheros QCA9563
- RAM : DDR2 128 MiB
- Flash : SPI-NOR 8 MiB
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : QCA9563 (SoC)
- 5 GHz : QCA9888
- Ethernet : 2x 10/100/1000 Mbps
- Switch : QCA8334
- LEDs/Input : 12x/4x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB
- JP1: Vcc, GND, NC, TX, RX from power connector side
- 115200 bps
Flash instruction using factory image:
1. Boot WG1200CR normaly
2. Access to "http://192.168.10.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt factory image and click update ("更新") button
to perform firmware update
4. Wait ~150 seconds to complete flashing
Known issues:
- cannot be controlled LEDs other than Power (Green/Red)
- only Power LEDs are connected to SoC GPIO; other LEDs
connected to the gpiochip on ath10k chip (QCA9888)
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [commit
message formatting]
INAGAKI Hiroshi [Sat, 16 Mar 2019 04:19:24 +0000 (13:19 +0900)]
firmware-utils: add nec-enc
nec-enc provides firmware encoding/decoding with model specific key
for NEC devices.
known devices:
- Aterm WF1200CR
- Aterm WG1200CR
- Aterm WG2600HS
usage:
nec-enc -i infile -o outfile -k key
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[checkpatch fixes, marked usage as noreturn, added static function,
moved buf* from stack to the global data segment]
Chuanhong Guo [Fri, 29 Mar 2019 09:46:36 +0000 (17:46 +0800)]
ramips: backport mt7621-spi from linux-next-
20190329
Upstream driver has gone through a series of cleanup and was moved
from drivers/staging into drivers/spi. Backport it to replace our
messy driver.
Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de>
[LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module]
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Tian Xiao bo <peterwillcn@gmail.com>
[Newifi-D2 MediaTek MT7621 ver:1 eco:3]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Eneas U de Queiroz [Thu, 28 Mar 2019 16:58:07 +0000 (16:58 +0000)]
build: remove sgid permission from tar
Otherwise tar will keep the sgid bit when running
from a sgid-set directory, resulting in a different
file being generated.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[reworked commit message, removed DMARC]
Michael Heimpold [Tue, 26 Mar 2019 21:09:14 +0000 (22:09 +0100)]
wpan-tools: clean up Makefile
When we only call the default, we do not need to define it explicitly.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Michael Heimpold [Tue, 26 Mar 2019 21:09:24 +0000 (22:09 +0100)]
fconfig: cleanup Makefile
We do not need to define an empty Build/Configure since
the default checks for existing ./configure and does nothing
in case nothing is found.
Similar for Build/Compile: we can remove the definition
when we only call the default.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Rosen Penev [Wed, 27 Mar 2019 07:50:16 +0000 (00:50 -0700)]
tools/xz: Compile with PIC to fix linking errors
I made a similar change to this here:
https://github.com/openwrt/packages/pull/8159
However, it turns out this did not fix the problem as the problem has to
do with tools/xz and not the xz package. The error is the same and causes
linking errors as can be seen above.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Adrian Schmutzler [Wed, 27 Mar 2019 18:14:34 +0000 (19:14 +0100)]
ath79: Utilize tplink-safeloader definition
Currently, tplink-safeloader definition is only used a base for
another common definition.
This patch adjusts tplink-safeloader so it can be actually used
for some targets in generic-tp-link.mk.
This patch is cosmetic except for the order of
"check-size $$$$(IMAGE_SIZE)" and "append-metadata" exchanged
for the tplink_re350k-v1 .
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [dealed with
tplink_cpe210-v2 and tplink_cpe210-v3, removed tplink-safeloader-uimage's
extra IMAGE/sysupgrade.bin rule]
Rosen Penev [Wed, 27 Mar 2019 20:39:49 +0000 (13:39 -0700)]
kernel: Add RIPEMD160 module
After getting rid of cryptsetup's heavy openssl dependency, there is now
the problem of missing RIPEMD160 support. RIPEMD160 is used for True/Vera
crypt volumes as well as old LUKS1 ones.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
David Bauer [Thu, 28 Mar 2019 19:58:04 +0000 (20:58 +0100)]
ramips: enable R6120 USB power
Enable the USB power for the Netgear R6120. Otherwise, no power is
supplied to an attached USB device.
Signed-off-by: David Bauer <mail@david-bauer.net>
Michael Gray [Sun, 17 Mar 2019 11:46:59 +0000 (22:46 +1100)]
tools: tplink-safeloader: add C7v5 KR Support
The added entry originates from TP-Links latest Archer C7 v5 KR firmware.
Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
Tomasz Maciej Nowak [Thu, 21 Mar 2019 17:03:39 +0000 (18:03 +0100)]
ath79: engenius epg5000: add leds migration script
With transition from ar71xx to ath79 some of devices change their naming
of LEDs. When upgrading from ar71xx target images this will require the
user to adjust previously working configuration. This commit adds
migration script which can be used to rename old names to new ones.
With this previously working configuration will be automatically
adjusted, wihtout user intervention.
This commit adds migration case for EnGenius EPG5000, the wireless LEDs
names have changed from epg5000:blue:wlan2-g and epg5000:blue:wlan-5g to
epg5000:blue:wlan2g and epg5000:blue:wlan5g.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Thu, 21 Mar 2019 17:03:38 +0000 (18:03 +0100)]
base-files: add leds migration
Currently leds migration scripts in ar71xx and lantiq share a lot of
logic and introducing leds migration to another target would mean
copying this code, again. Therefore add common logic to library in
base-files package.
Suggested-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Zhao Yu [Mon, 11 Mar 2019 16:21:58 +0000 (16:21 +0000)]
ramips: add support for Youku YK-L2
Hardware spec:
CPU: MTK MT7621A
RAM: 256MB
ROM: 16MB SPI Flash
WiFi: MT7603EN + MT7612EN
Button: 2 buttons (reset, wps)
LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB)
Ethernet: 3 ports, 2 LAN + 1 WAN
Other: USB3.0
Flashing instructions:
Visit the openwrt forum topic for this router:
https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692
to get the bootloader and unlock firmware.
0. upgrade your router with the telnet firmware via the
firmware upgrade page on the webui.
1. telnet 192.168.11.1 from your PC
2. Download the pb-boot-youku_l2-
20190317-
61b6d33.bin and transfer
it to the /tmp directory of the router.
3. mtd write /tmp/pb-boot-youku_l2-
20190317-
61b6d33.bin Bootloader
4. turn off the power
5. Push the reset button while turning on the router and
wait until LED start blinking (~10sec.)
6. Connect Ethernet port and goto http://192.168.1.1.
7. Upload the firmware to firmware restore page in webui.
Signed-off-by: Zhao Yu <574249312@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the
flashing instructions, fixed author]
Jason A. Donenfeld [Sat, 6 Apr 2019 11:24:09 +0000 (13:24 +0200)]
wireguard: bump to 0.0.
20190406
* allowedips: initialize list head when removing intermediate nodes
Fix for an important regression in removing allowed IPs from the last
snapshot. We have new test cases to catch these in the future as well.
* tools: warn if an AllowedIP has a nonzero host part
If you try to run `wg set wg0 peer ... allowed-ips 192.168.1.82/24`, wg(8)
will now print a warning. Even though we mask this automatically down to
192.168.1.0/24, usually when people specify it like this, it's a mistake.
* wg-quick: add 'strip' subcommand
The new strip subcommand prints the config file to stdout after stripping
it of all wg-quick-specific options. This enables tricks such as:
`wg addconf $DEV <(wg-quick strip $DEV)`.
* tools: avoid unneccessary next_peer assignments in sort_peers()
Small C optimization the compiler was probably already doing.
* peerlookup: rename from hashtables
* allowedips: do not use __always_inline
* device: use skb accessor functions where possible
Suggested tweaks from Dave Miller.
* blake2s: simplify
* blake2s: remove outlen parameter from final
The blake2s implementation has been simplified, since we don't use any of the
fancy tree hashing parameters or the like. We also no longer separate the
output length at initialization time from the output length at finalization
time.
* global: the _bh variety of rcu helpers have been unified
* compat: nf_nat_core.h was removed upstream
* compat: backport skb_mark_not_on_list
The usual assortment of compat fixes for Linux 5.1.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Daniel Engberg [Thu, 7 Feb 2019 23:41:47 +0000 (23:41 +0000)]
target/octeon: Add Linux 4.19 support
This commit adds support for Linux 4.19 kernel, various cleanups
listed below.
Drop 170-cisco-hack.patch as these devices never seems to have been
supported.
Unset kernel symbols:
* CONFIG_CAVIUM_CN63XXP1=y
No supported hardware uses CN63XXP1 and it causes "slight decrease in
performance"
Source: https://cateee.net/lkddb/web-lkddb/CAVIUM_CN63XXP1.html
* CONFIG_USB_OCTEON_EHCI=y
CONFIG_USB_OCTEON_OHCI=y
Deprecated
Source: https://cateee.net/lkddb/web-lkddb/USB_OCTEON_EHCI.html
https://cateee.net/lkddb/web-lkddb/USB_OCTEON_OHCI.html
Removed kernel symbols:
* # CONFIG_ARCH_HIBERNATION_POSSIBLE=y
* CONFIG_ARCH_SUSPEND_POSSIBLE=y
These are not in if you do a vanilla config of a MIPS Octeon kernel
and I can't find any references about support on this platform.
* # CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
* CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
No need to have this in by default, not defined in most other targets
* CONFIG_CRASH_CORE=y
Can't find any documentation why this should be enabled by default
* CONFIG_DEBUG_INFO=y
Set by https://github.com/openwrt/openwrt/blob/master/config/Config-kernel.in#L134
* CONFIG_DEBUG_SPINLOCK=y
No need to have this in by default
* CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=120
Already set by default
Source: https://cateee.net/lkddb/web-lkddb/DEFAULT_HUNG_TASK_TIMEOUT.html
* CONFIG_DETECT_HUNG_TASK=y
No need to have this in by default, not defined in most other targets
* CONFIG_HAVE_DEBUG_KMEMLEAK=y
No need to have this in by default, not defined in most other targets
* CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
No need to have this in by default
* CONFIG_HAVE_IDE=y
None of the supported devices have IDE
* CONFIG_HZ=250
* # CONFIG_HZ_100 is not set
* CONFIG_HZ_250=y
This is broken with generic config
* CONFIG_KALLSYMS=y
No need to have this in by default, not defined in most other targets
* CONFIG_KEXEC=y
* CONFIG_KEXEC_CORE=y
No need to have this in by default, not defined in most other targets
* CONFIG_HAVE_KVM=y
No need to have this in by default
* CONFIG_SCHED_DEBUG=y
No need to have this in by default, not defined in most other targets
* CONFIG_SYSFS_DEPRECATED=y
Deprecated symbol
Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED.html
* CONFIG_SYSFS_DEPRECATED_V2=y
Discouraged usage in general
Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED_V2.html
* CONFIG_UNINLINE_SPIN_UNLOCK=y
No need to have this in by default, not defined in most other targets
Source: https://github.com/openSUSE/kernel/blob/master/lib/Kconfig.debug#L1137
* CONFIG_ZLIB_INFLATE=y
No need to have this in by default, not defined in most other targets
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Tomasz Maciej Nowak [Thu, 28 Mar 2019 17:07:09 +0000 (18:07 +0100)]
mvebu: sysupgrade: sdcard: keep user added partitons
Currently sysupgrade overwrites whole disk and destroys partitions added
by user. Sync the sysupgrade code with the one present in x86 target to
remedy this behaviour.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Thu, 28 Mar 2019 17:07:08 +0000 (18:07 +0100)]
mvebu: base-files: autodetect upgrade device
Since some boards could be also booted from other mediums than SD card,
lets make the upgrade block device autodetected.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Thu, 28 Mar 2019 17:07:07 +0000 (18:07 +0100)]
mvebu: shrink amount of packages and reorganize them
Since most of devices using SD card image to boot, use ext4 as boot
files system we can drop fat fs related packages. Also move packages
which are added repeatedly across subtargets to their default packages,
with droping the ones that are enabled in target kernel configugation.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Thu, 28 Mar 2019 17:07:06 +0000 (18:07 +0100)]
mvebu: use ext4 for clearfog image bootfs
This will allow to drop additional packages and shrink image size.
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Thu, 28 Mar 2019 17:07:05 +0000 (18:07 +0100)]
mvebu: make bootfs size for sdcard image configurable
Let's take this oportunity to implement boot-part and rootfs-part feature
flags.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Luis Araneda [Mon, 1 Apr 2019 03:33:08 +0000 (00:33 -0300)]
zynq: replace storage related configs by packages
Select build-in packages by default and remove the
associated kernel configs
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Luis Araneda [Mon, 1 Apr 2019 03:33:07 +0000 (00:33 -0300)]
zynq: replace CAN kconfig options by device packages
The options are managed on a generic way by the can
kmod packages
Additionally, select can packages only for devices that
currently has CAN enabled, which is only the ZC702
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Luis Araneda [Mon, 1 Apr 2019 03:33:06 +0000 (00:33 -0300)]
kernel: can: add Xilinx CAN IP kernel module package
This driver is required to use the CAN IP on devices
from the zynq target
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Luis Araneda [Mon, 1 Apr 2019 03:33:05 +0000 (00:33 -0300)]
zynq: kernel: remove video/camera kconfig options
The options are managed on a generic way by video packages
Additionally, only one of the currently supported boards
has a camera interface, but it requires programming
the FPGA fabric first
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Luis Araneda [Mon, 1 Apr 2019 03:33:04 +0000 (00:33 -0300)]
zynq: kernel: remove sound kconfig options
The options are managed on a generic way by the sound
kmod packages
Additionally, none of the currently supported boards have
sound support out of the box, as they require programming
the FPGA fabric first
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Luis Araneda [Mon, 1 Apr 2019 03:33:03 +0000 (00:33 -0300)]
kernel: sound: add missing symbol to sound-soc-core
This fixes compilation on zynq target when migrating
to sound kmod packages
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Luis Araneda [Mon, 1 Apr 2019 03:33:02 +0000 (00:33 -0300)]
zynq: kernel: refresh config
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Hauke Mehrtens [Thu, 28 Mar 2019 15:00:43 +0000 (16:00 +0100)]
mac80211: update to version 4.19.32-1
The removed patches are now integrated in the upstream kernel.
Refresh all patches on top of the new backports release.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Josef Schlehofer [Fri, 29 Mar 2019 23:51:58 +0000 (00:51 +0100)]
mbedtls: update to version 2.16.1
Refreshed patches
Signed-off-by: Josef Schlehofer <josef.schlehofer@nic.cz>
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Tomasz Maciej Nowak [Mon, 1 Apr 2019 17:25:44 +0000 (19:25 +0200)]
tegra: add kernel 4.19 support
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Mon, 1 Apr 2019 17:25:43 +0000 (19:25 +0200)]
tegra: add support for CompuLab TrimSlice
It is a small form factor computer with rich amount of expansion ports.
Some hardware specs and supported features in this commit:
CPU: NVIDIA Tegra 2 @ 1GHz
RAM: 1GB DDR2-667
Storage: SDHC card slot
µSDHC card slot
USB to SATA bridge (depends on model)
1MB SPI NOR flash for bootloader (single partition)
LAN: RTL8111DL GbE
WIFI: RT3070 b/g/n with external antenna (depends on model)
RTC: EM3027 (mapped as rtc0; with battery backup)
Tegra 2 built-in (mapped as rtc1)
Sound: Analog/Digital (TLV320AIC23b; S/PDIF not tested)
Connectors: 4x USB 2.0
RS232 (mini serial)
HDMI
DVI-D (depends on model, not supported atm)
Extension connector (24 pin ZIF, 0.5mm pitch):
2X UART
SPI
JTAG (1.8V)
Other: power button with green led (not functional for early revisions
without programmed PMIC)
2x GPIO configurable green led
TrimSlice uses U-Boot placed in NOR flash. Boots Linux from any media
connected to USB, SATA or SD card inserted in slot. Can also boot from
TFTP. To run OpenWrt one needs to update U-Boot to fairly recent version
(the versions, pre-dts/dts provided by CompuLab won't suffice):
1. Boot TrimSlice into Your current linux distro,
2. Download trimslice-spi.img from u-boot-trimslice subdir,
3. Install mtd-utils,
4. Run following commands:
flash_erase /dev/mtd0 0 256
nandwrite /dev/mtd0 trimslice-spi.img
5. Poweroff, insert SD card with OpenWrt, boot and enjoy.
If by some obstacle You can't follow those instructions, it is possible
to flash U-Boot using serial console.
1. Insert FAT or EXT2/EXT3 formatted SD card with trimslice-spi.img,
2. Interrupt boot process to enter U-Boot command line,
3. Run following commands:
${fs}load mmc 0 0x04080000 trimslice-spi.img
sf probe 0
sf erase 0 0x100000
sf write 0x04080000 0x0 ${filesize}
reset
4. Poweroff, insert SD card with OpenWrt, boot and enjoy.
If something went wrong with one of above steps, there is simple
recovery option:
1. Open the µSD slot security door to access the recovery-boot button,
2. Insert SD card with OpenWrt to the front slot while unpowered,
3. Power on the TrimSlice while pressing the recovery-boot button,
4. With this it should boot straigth to OpenWrt, from there download
trimslice-spi.img and execute following commands:
mtd erase /dev/mtd0
mtd write trimslice-spi.img /dev/mtd0
5. Reboot, now it should boot straigth to OpenWrt, without pressing the
recovery-boot button, with proper U-Boot flashed.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Mon, 1 Apr 2019 17:25:42 +0000 (19:25 +0200)]
kernel: package rtc-em3027 module
Support for Microelectronic EM3027 real time clock chip.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Mon, 1 Apr 2019 17:25:41 +0000 (19:25 +0200)]
uboot-tegra: add U-Boot for tegra boards
Add U-Boot for NVIDIA Tegra based boards, with the first being CompuLab
TrimSlice. This is part of initial support for this board.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Mon, 1 Apr 2019 17:25:40 +0000 (19:25 +0200)]
tools: add cbootimage-configs for tegra
This provides board configuraion tables for various Tegra boards needed
by cbootimage tool to create flashable bootloader images.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Mon, 1 Apr 2019 17:25:39 +0000 (19:25 +0200)]
tools: add cbootimage for tegra
Tegra BCT and bootable flash image generator/compiler
>From documentation:
This project provides a tool which compiles BCT (Boot Configuration
Table) images to place into the boot flash of a Tegra-based device.
The tool will either:
a) Compile a textual representation of a BCT into a binary image.
b) Generate an entire boot image from a previously compiled BCT and a
bootloader binary.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tomasz Maciej Nowak [Mon, 1 Apr 2019 17:25:38 +0000 (19:25 +0200)]
tegra: add new target
New target introduces initial support for NVIDIA Tegra SoC based devices.
It focuses on Tegra 2 CPUs, for successors supporting NEON instruction
set the target should be split in two subtargets.
This initial commit doesn't create any device image, it's groundwork
for further additions.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Daniel Engberg [Fri, 5 Apr 2019 17:43:59 +0000 (17:43 +0000)]
curl: Update to 7.64.1
Update curl to 7.64.1
Remove deprecated patch
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Hans Dedecker [Fri, 5 Apr 2019 09:57:54 +0000 (11:57 +0200)]
odhcpd: update to latest git HEAD
65a9519 ndp: create ICMPv6 socket per interface
c6dae8e router: create ICMPv6 socket per interface
e7b1d4b treewide: initialize properly file descriptors
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Michael Heimpold [Tue, 2 Apr 2019 19:48:11 +0000 (21:48 +0200)]
base-files/hotplug: fix dedicated group for tty devices
Commit
124ab1dc0a and
5523ee3459 introduced the assignment of the
group "tty" to /dev/tty* devices in order to support unprivileged
user access to serial devices.
However, due to an improperly rebased commit this feature broke.
This patch restores the lost hunk in hotplug.json file to
re-introduce this feature and also renames the existing "tty" group
to "dialout" as this is the more typical name for such a group
on desktop systems.
Fixes: 5209cfa534 ("procd: fix hotplug.json syntax")
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Rafał Miłecki [Thu, 4 Apr 2019 09:31:28 +0000 (11:31 +0200)]
kernel: b53: add support for kernels 5.0+
It adjusts b53 code to upstream changes from the commit
3c1bcc8614db
("net: ethernet: Convert phydev advertize and supported from u32 to link
mode").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Thu, 4 Apr 2019 09:18:27 +0000 (11:18 +0200)]
kernel: backport upstream ubifs default compression selection fix
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Rafał Miłecki [Thu, 4 Apr 2019 07:31:41 +0000 (09:31 +0200)]
kernel: fix rtcache compilation with 4.18+ with IPv6 support
Please note that modified code isn't currently being compiled with
kernels 4.19+ due to the dropped CONFIG_NF_CONNTRACK_IPV6 in upstream
Linux. That requires a separated fix.
This fixes:
net/netfilter/nf_conntrack_rtcache.c: In function 'nf_rtcache_get_cookie':
net/netfilter/nf_conntrack_rtcache.c:82:11: error: 'const struct rt6_info' has no member named 'rt6i_node'; did you mean 'rt6i_idev'?
if (rt->rt6i_node)
^~~~~~~~~
rt6i_idev
IPv6 structs were reworked in upstream kernel by:
commit
a64efe142f5e ("net/ipv6: introduce fib6_info struct and helpers")
commit
77634cc67dc1 ("net/ipv6: Remove unused code and variables for rt6_info")
commit
93c2fb253d17 ("net/ipv6: Rename fib6_info struct elements")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Felix Fietkau [Sat, 30 Mar 2019 09:09:32 +0000 (10:09 +0100)]
mac80211: set noscan=1 if sta/adhoc/mesh interfaces are present
Fixes channel selection issues and suppresses an unnecessary extra scan
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 23 Mar 2019 08:59:35 +0000 (09:59 +0100)]
mac80211: improve performance by deferring tx queue selection
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Felix Fietkau [Sat, 23 Mar 2019 13:29:00 +0000 (14:29 +0100)]
ramips: implement vlan rx offload on MT7621
Avoids the overhead of software VLAN untagging in the network stack
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Magnus Kroken [Tue, 2 Apr 2019 20:18:44 +0000 (22:18 +0200)]
openvpn: openssl: explicitly depend on deprecated APIs
OpenVPN as of 2.4.7 uses some OpenSSL APIs that are deprecated in
OpenSSL >= 1.1.0.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [white space fix]
Adrian Schmutzler [Mon, 25 Mar 2019 17:46:26 +0000 (18:46 +0100)]
ath79: Add support for TP-Link CPE210 v2
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on
for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
This is based on the support patch for the identical CPE210 v3
by Mario Schroen <m.schroen@web.de>.
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Mario Schroen [Sun, 31 Mar 2019 19:07:03 +0000 (21:07 +0200)]
ath79: Add support for TP-Link CPE210 v3
Specifications:
* SoC: Qualcomm Atheros QCA9533 (650MHz)
* RAM: 64MB
* Storage: 8 MB SPI NOR
* Wireless: 2.4GHz N based built into SoC 2x2
* Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI or TFTP
To get to TFTP recovery just hold reset button while powering
on for around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Thanks to robimarko for the work inside the ar71xx tree.
Thanks to adrianschmutzler for deep discussion and fixes.
Signed-off-by: Mario Schroen <m.schroen@web.de>
[Split into DTS/DTSI, read-only config partition in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
[renamed dtsi filename, light subject touches]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Robert Marko [Sat, 11 Aug 2018 15:32:48 +0000 (17:32 +0200)]
ar71xx: Add support for TP-Link CPE210 v3
Looks identical to the v2.
This PR adds support for a popular low-cost 2.4GHz N based AP
Specifications:
- SoC: Qualcomm Atheros QCA9533 (650MHz)
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC 2x2
- Ethernet: 1x 100/10 Mbps, integrated into SoC, 24V POE IN
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[Rebased, adjusted for separate tplink-safeloader entry, dynamic partitioning]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Adrian Schmutzler [Tue, 26 Mar 2019 10:41:57 +0000 (11:41 +0100)]
ar71xx: Use dynamic partitions for TP-Link CPE210 v2
This is also helpful to add support in ath79.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hans Dedecker [Mon, 1 Apr 2019 21:08:58 +0000 (23:08 +0200)]
netifd: update to latest git HEAD
361b3e4 proto-shell: return error in case setup fails
a97297d interface: set interface in TEARDOWN state when checking link state
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Petr Štetiar [Mon, 1 Apr 2019 11:53:31 +0000 (13:53 +0200)]
build: image: Fix off-by-one in DTC kernel version checks
It was reported to me on IRC today, that my change causes issues with
kernel versions between 4.14 and 4.19.
It's because I've wrongly used `git describe` in order to get kernel
version where we should disable noisy DTC checks, but I should've used
`git tag --contains` instead.
Fixes: cbbef976e2b ("build: dtc: Disable noisy warnings by default")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Petr Štetiar [Mon, 1 Apr 2019 10:03:50 +0000 (12:03 +0200)]
ar71xx: ens202ext: Fix whitespace issues
I've missed leading whitespace issues in the original patch, so fixing
it in this commit. Thanks to pepe2k for letting me know.
Fixes: d260813d ("ar71xx: ens202ext: Fix VLAN switch")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Magnus Kroken [Wed, 27 Mar 2019 19:07:58 +0000 (20:07 +0100)]
openvpn: update to 2.4.7
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
Kabuli Chana [Sun, 3 Mar 2019 20:53:23 +0000 (13:53 -0700)]
mwlwifi: Fix pcie timeout issue
Increase MAX_WAIT_FW_COMPLETE_ITERATIONS to 10000 as before commit
e5e0700 to prevent timeout as reported here: #308 (Original OP issue is
probably not related though as his post preceeds commit
e5e0700).
compile/test target mvebu/mamba, rango
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
[commit subject and message tweaks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
David Bauer [Fri, 29 Mar 2019 15:16:18 +0000 (16:16 +0100)]
ramips: add missing SPDX identifier for EX6150
This adds the SPDX license identifier for the NETGEAR EX6150. It was
missed when submitting the original patch.
Signed-off-by: David Bauer <mail@david-bauer.net>
Michael Pratt [Fri, 22 Feb 2019 05:28:50 +0000 (00:28 -0500)]
ar71xx: ens202ext: Fix VLAN switch
The target ENS202EXT was just recently added right before the stable
release of Openwrt 18.
It flashes fine, but the physical switch is almost impossible to use
until you have a VLAN set up. Tested on two devices.
The actual problem is that eth0 represents nothing for whatever reason.
In other words, both WAN and LAN are running from eth1. There may be an
underlying problem in the build, but for now, I assume that this is
correct and that a VLAN switch is an appropriate fix.
Also, it's virtually impossible to get the switch running right through
LuCI. It is one thing to get a switch to appear, but attempting to
configure it breaks the whole thing. The VLAN has to be set up
perfectly, otherwise, interfaces will not start up, and one is forced to
reset settings, OR, the new LuCI feature kicks in and reverses any
steps. It is extremely difficult to determine which virtual ports
correspond to which physical ethernet ports without being able to set up
the switch in LuCI.
Temporary Workaround: followed directions here
[openwrt/luci#867](https://github.com/openwrt/luci/issues/867)
Reviewed-by: Marty Plummer <hanetzer@startmail.com>
Signed-off-by: Michael Pratt <mpratt51@gmail.com>
[commit author fix, subject fix, message text wrap]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Christian Lamparter [Sat, 30 Mar 2019 09:33:47 +0000 (10:33 +0100)]
ath10k-firmware: update Candela Tech firmware images
Release notes since last time:
Release notes for wave-1 / 10.1:
2019-03-28: Fix sometimes using bad TID for management frames
in htt-mgt mode. (Backported from wave2, looks
like bug would be the same though.)
Release notes for wave-2 / 10.4:
2019-03-28: Fix off-channel scanning while associated in
proxy-station mode.
2019-03-29: Fix sometimes sending mgt frames on wrong tid when
using htt-mgt. This bug has been around since I first
enabled htt-mgt mode.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hans Dedecker [Fri, 29 Mar 2019 14:45:28 +0000 (15:45 +0100)]
odhcpd: update to latest git HEAD
7798d50 netlink: rework IPv4 address refresh logic
0b20876 netlink: rework IPv6 address refresh logic
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Koen Vandeputte [Thu, 28 Mar 2019 11:59:20 +0000 (12:59 +0100)]
kernel: bump 4.14 to 4.14.109
Refreshed all patches.
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Thu, 28 Mar 2019 11:57:03 +0000 (12:57 +0100)]
kernel: bump 4.9 to 4.9.166
Refreshed all patches.
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Rosen Penev [Thu, 14 Feb 2019 21:15:29 +0000 (13:15 -0800)]
ramips: Increase GB-PC1 SPI frequency to 80MHz
The specific flash chip used (W25Q256FVEM) accepts 50MHz for read
requests and higher for others. 104MHz for fast reads. ramips seems to
be limited to 80MHz based on testing with higher values (no speedup).
Based on upstream commit:
97738374a310b9116f9c33832737e517226d3722
time dd if=/dev/mtdblock3 of=/dev/null bs=64k from 42.96s to 7.01s
[test done with backported upstream v4.19 driver[1], for numbers on
stock 4.14 driver please take a look at `ramips: Increase GB-PC2 SPI
frequency to 80MHz` commit message]
1. https://github.com/openwrt/openwrt/pull/1578
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[expanded note about spi driver version]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Rosen Penev [Fri, 29 Mar 2019 06:01:30 +0000 (23:01 -0700)]
ramips: Increase GB-PC2 SPI frequency to 80MHz
The flash chip on the board (Spansion S25FL256SAIF00) is rated to
support at least 50MHz for normal read requests according to the
datasheet. 133MHz for fast reads. However, ramips seems to be limited to
80MHz.
>From testing this, higher values do not improve speeds.
time dd if=/dev/mtdblock3 of=/dev/null bs=64k from
42.82s to 14.09s.
boot speed is also faster:
[ 66.884087] procd: - init - vs
[ 48.976049] procd: - init -
Since spi speed was requested:
[ 3.538884] spi-mt7621
1e000b00.spi: sys_freq:
225000000
CPU is 900MHz:
[ 0.000000] CPU Clock: 900MHz
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[fixed commit message by adding missing 0 in the spi-mt7621 clock output]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
David Bauer [Thu, 21 Mar 2019 14:55:09 +0000 (15:55 +0100)]
ramips: add Netgear EX6150
SoC: MediaTek MT7621
RAM: 64M (Winbond W9751G6KB-25)
FLASH: 16MB (Macronix MX25L12835F)
WiFi: MediaTek MT7662E bgn 2SS
WiFi: MediaTek MT7662E nac 2SS
BTN: ON/OFF - Reset - WPS - AP/Extender toggle
LED: - Arrow Right (blue)
- Arrow Left (blue)
- WiFi 1 (red/green)
- WiFi 2 (red/green)
- Power (green/amber)
- WPS (Green)
UART: UART is present as Pads on the backside of the PCB. They are
located on the other side of the Ethernet port.
3.3V - GND - TX - RX / 57600-8N1
3.3V is the nearest one to the antenna connectors
Installation
------------
Update the factory image via the Netgear web-interfaces (by default:
192.168.1.250/24).
You can also use the factory image with the nmrpflash tool.
For more information see https://github.com/jclehner/nmrpflash
Signed-off-by: David Bauer <mail@david-bauer.net>
[merge conflict in 02_network, flash@0 node rename, wlan DTS triggers]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Vladimir Kot [Sat, 12 Jan 2019 09:43:28 +0000 (18:43 +0900)]
ramips: add support for ZyXEL Keenetic Start
Device specification:
- SoC: RT5350F
- CPU Frequency: 360 MHz
- Flash Chip: Winbond 25Q32 (4096 KiB)
- RAM: 32768 KiB
- 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN)
- 1x external, non-detachable antenna
- UART (J1) header on PCB (57800 8n1)
- Wireless: SoC-intergated: 2.4GHz 802.11bgn
- USB: None
- 3x LED, 2x button
Flash instruction:
1. Configure PC with static IP 192.168.1.2/24 and start TFTP server.
2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin"
to "kstart_recovery.bin" and place it in TFTP server directory.
3. Connect PC with one of LAN ports, press the reset button, power up
the router and keep button pressed until power LED start blinking.
4. Router will download file from TFTP server, write it to flash and reboot.
Signed-off-by: Vladimir Kot <vova28rus@gmail.com>
[fixed git commit author and whitespace issues in DTS]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Tobias Welz [Fri, 11 Jan 2019 23:37:43 +0000 (00:37 +0100)]
ramips: add support for WIZnet WizFi630S board
The WIZnet WizFi630S board is in the miniPCIe form factor.
SoC: Mediatek MT7688AN
RAM: 128MB
Flash: 32Mb
WiFi: 2.4GHz
Ethernet: 3x 100Mbit
USB: 1 (USB 2.0)
serial ports: 2 (1x full, 1xlite)
Flash and recovery instructions: Use the factory installed u-boot boot
loader. It is available on UART2 (115200,8,n,1). Then get the
sysupgrade image from a tftp server.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
[whitespace and device name in makefile fixes]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Daniel Golle [Thu, 28 Mar 2019 14:09:38 +0000 (15:09 +0100)]
iwinfo: Fix 802.11ad channel to frequency
c2cfe9d iwinfo: Fix 802.11ad channel to frequency
Fixes
9725aa271a ("iwinfo: update to latest git HEAD")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Petr Štetiar [Thu, 28 Mar 2019 11:57:08 +0000 (12:57 +0100)]
fstools: update to the latest master branch
ff1ded6 libfstools: Fix overflow of F2FS_MINSIZE constant
bc2c876 libfstools: Print error in case of loop blkdev failure
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Alexander Couzens [Sat, 16 Mar 2019 22:19:04 +0000 (23:19 +0100)]
package/uboot-omap: backport patches to fix build
* 106: fix build when libfdt-devel is installed on host
* 107: fix stdbool.h includes
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Daniel Golle [Wed, 27 Mar 2019 21:59:03 +0000 (22:59 +0100)]
wireguard: introduce 'nohostroute' option
Instead of creating host-routes depending on fwmark as (accidentally)
pushed by commit
1e8bb50b93 ("wireguard: do not add host-dependencies if fwmark is set")
use a new config option 'nohostroute' to explicitely prevent creation
of the route to the endpoint.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Wed, 27 Mar 2019 21:52:05 +0000 (22:52 +0100)]
IB: fix generating .profile.mk for profiles without metadata
Fixes
d6fa04a437 ("IB: include SUPPORTED_DEVICES in 'make info' output")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Daniel Golle [Tue, 19 Mar 2019 15:47:17 +0000 (16:47 +0100)]
wireguard: do not add host-dependencies if fwmark is set
The 'fwmark' option is used to define routing traffic to
wireguard endpoints to go through specific routing tables.
In that case it doesn't make sense to setup routes for
host-dependencies in the 'main' table, so skip setting host
dependencies if 'fwmark' is set.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hans Dedecker [Wed, 27 Mar 2019 20:03:02 +0000 (21:03 +0100)]
odhcpd: update to latest git HEAD (FS#2204)
420945c netlink: fix IPv6 address updates (FS#2204)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Koen Vandeputte [Wed, 27 Mar 2019 15:46:39 +0000 (16:46 +0100)]
kernel: fix missing dependency in 4.14.108
The 4.14.108 bump introduced a missing dependency when building
specific netfilters.
Thsi was not seen as the error does not occur on all targets.
Thanks to Jo-Philipp Wich for providing the fix
Fixes: af6c86dbe56e ("kernel: bump 4.14 to 4.14.108")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Felix Fietkau [Wed, 27 Mar 2019 12:03:01 +0000 (13:03 +0100)]
mt76: update to the latest version
f2a18f5 mt76x02: introduce mt76x02_beacon.c
91ade88 mt76x02: add hrtimer for pre TBTT for USB
6370485 mt76x02: introduce beacon_ops
37af803 mt76x02u: implement beacon_ops
41d6190 mt76x02: generalize some mmio beaconing functions
dcccc04 mt76x02u: add sta_ps
5ac5289 mt76x02: disable HW encryption for group frames
e284cc2 mt76x02u: implement pre TBTT work for USB
77e56b8 mt76x02: make beacon slots bigger for USB
d4c740f mt76x02u: add mt76_release_buffered_frames
65e6344 mt76: unify set_tim
f720e49 mt76x02: enable AP mode for USB
cf1838d mt76usb: change mt76u_submit_buf
16b2ccf mt76: remove rx_page_lock
e1bfbeb mt76usb: change mt76u_fill_rx_sg arguments
e9c0171 mt76usb: use usb_dev private data
a4eb5db mt76usb: remove mt76u_buf redundant fileds
3f9b68d mt76usb: move mt76u_buf->done to queue entry
4a366bd mt76usb: remove mt76u_buf and use urb directly
0904bc4 mt76usb: remove MT_RXQ_MAIN queue from mt76u_urb_alloc
42f2899 mt76usb: resue mt76u_urb_alloc for tx
4d4d73a mt76usb: remove unneded sg_init_table
57309c7 mt76usb: allocate urb and sg as linear data
2e89721 mt76usb: remove queue variable from rx_tasklet
30a256a mt76x02: remove extra_tx_headroom (obsoleted by mac8211 skb aligning)
ae166b0 Revert "mt76: mt7603: store software PN/IV in wcid"
bf6e72d Revert "mt76: mt76x02: store software PN/IV in wcid"
a11b673 mt76: fix tx power issues
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Koen Vandeputte [Mon, 25 Mar 2019 10:40:22 +0000 (11:40 +0100)]
kernel: bump 4.14 to 4.14.108
Refreshed all patches.
Altered patches:
- 950-0033-i2c-bcm2835-Add-debug-support.patch
Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Koen Vandeputte [Mon, 25 Mar 2019 10:37:17 +0000 (11:37 +0100)]
kernel: bump 4.9 to 4.9.165
Refreshed all patches.
Compile-tested on: ar7
Runtime-tested on: none
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Stijn Tintel [Tue, 26 Mar 2019 17:35:55 +0000 (19:35 +0200)]
scripts/gen_image_generic.sh: fail on errors
The script always exits with value 0, even if some of the commands fail.
This can potentially create broken, unbootable images, e.g. when
make_ext4fs fails due to TARGET_KERNEL_PARTSIZE being too small for the
kernel. Avoid this by failing the script when any command fails.
Acked-by: Jo-Philipp Wich <jo@mein.io>
Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Koen Vandeputte [Fri, 22 Mar 2019 12:02:40 +0000 (13:02 +0100)]
ar71xx: add support for MikroTik RouterBOARD 922UAGS-5HPacD
This patch adds support for the MikroTik RouterBOARD 922UAGS-5HPacD
with a built-in 802.11ac High-Power radio (31dBm).
See https://mikrotik.com/product/RB922UAGS-5HPacD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9557 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9882 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE-in 24V
- SFP: 1x host
- USB: 1x 2.0 type A
- PCIe: 1x Mini slot (also contains USB 2.0 for 3G/LTE modems)
- SIM slot: 1x mini-SIM
Working:
- Board/system detection
- NAND storage detection
- PCIe
- USB: Type A & mini PCIe
- Wireless
- Ethernet
- LED's (excl. SFP and RSSI levels)
- Reset button
- Sysupgrade
Not working:
- SFP cage
Installation:
- Boot vmlinux-initramfs image via BOOTP/TFTP and then flash sysupgrade
image using "sysupgrade -n"
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Hauke Mehrtens [Thu, 21 Mar 2019 16:57:00 +0000 (17:57 +0100)]
mvebu: Add dependency to kmod-i2c-mux-pca954x for armada-macchiatobin
This driver is needed for the I2C mux on the board.
Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>