openwrt/openwrt.git
2 years agox86: geode: fix package nameing kmod-crypto-ebc does not exist
Florian Eckert [Tue, 22 Feb 2022 10:43:32 +0000 (11:43 +0100)]
x86: geode: fix package nameing kmod-crypto-ebc does not exist

This commit fixes the package naming that was added by commit:
e1e4cbde5ceb228e60fff1fc752cb90d9a7df2ab

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2 years agobcm63xx: Fast 2704n: configure the WAN port
Daniel González Cabanelas [Wed, 23 Feb 2022 17:35:23 +0000 (18:35 +0100)]
bcm63xx: Fast 2704n: configure the WAN port

The Sagem/Plusnet F@ST2704N has a red label in ethernet port 4. Its purpose is
to be used as Fibre/WAN with the stock firmware.

Configure the Eth4 as WAN.

Fixes: fbbb977772 (brcm63xx: Tune the network configuration for several
routers)

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2 years agompc85xx: HiveAP-330: add tmp125 temperature sensor
Christian Lamparter [Thu, 17 Feb 2022 20:15:54 +0000 (21:15 +0100)]
mpc85xx: HiveAP-330: add tmp125 temperature sensor

the Aerohive HiveAP-330 and HiveAP-350 come equipped
with an TI TMP125 temperature chip. This patch wires
up the necessary support for this sensor and exposes
it through hwmon / thermal sensor framework. Upstream
support is coming, but it has to go through hwmon-next
first.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agokernel: add disabled PSTORE+REED_SOLOMON symbols for 5.4
Christian Lamparter [Fri, 25 Feb 2022 07:13:36 +0000 (08:13 +0100)]
kernel: add disabled PSTORE+REED_SOLOMON symbols for 5.4

The last remaining 5.4 target currently chokes because the
symbols haven't been disabled like for 5.10.

Fixes: 97158fe10e60 ("kernel: package ramoops pstore-ram crash log storage")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agomac80211: add #if guards against 5.4 compile failures
Christian Lamparter [Fri, 25 Feb 2022 07:11:36 +0000 (08:11 +0100)]
mac80211: add #if guards against 5.4 compile failures

Both struct net_device_path_ctx and struct net_device_path
are not available in 5.4. This causes an build error on the
bcm63xx target.

|mac80211/driver-ops.h: In function 'drv_net_fill_forward_path':
|driver-ops.h:1502:57: error: passing argument 4 of
|'local->ops->net_fill_forward_path' from incompatible pointer type
| [-Werror=incompatible-pointer-types]
| 1502 |                          ctx, path);
|      |                          ^~~
|      |                            |
|      |                         struct net_device_path_ctx *

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agotools/quilt: update to 0.67
Rosen Penev [Fri, 25 Feb 2022 04:19:32 +0000 (20:19 -0800)]
tools/quilt: update to 0.67

  - Call pager with original LANG environment variable
  - Consistently complain early if no series file is found
  - Fix handling of symbolic links by several commands
  - Tighten the patch format parsing
  - Reuse the shell (performance)
  - Document the series file format further
  - Document that quilt loads /etc/quilt.quiltrc
  - configure: Make stat configurable
  - series: Minor optimizations
  - setup: Don't obey the settings of any englobing .pc
  - setup: Default to fast mode
  - quilt.el: Fix documentation of quilt-pc-directory
  - quilt.el: Load /etc/quilt.quiltrc if ~/.quiltrc doesn't exist
  - quilt.el: Fix quilt-editable when QUILT_PATCHES_PREFIX is set

Refresh patches.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
[add changelog]
Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agoCI: build changes in tools/ on ubuntu/macos
Paul Spooren [Fri, 25 Feb 2022 11:28:46 +0000 (12:28 +0100)]
CI: build changes in tools/ on ubuntu/macos

This commits adds GitHub CI to check that all tools compile on both
Ubuntu and macOS. Since running in parrallel this should also detect
badly set depdendencies within tools/Makefile.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agobcm4908: fix USB PHY support
Rafał Miłecki [Fri, 25 Feb 2022 09:47:08 +0000 (10:47 +0100)]
bcm4908: fix USB PHY support

This fixes problem with USB PHY not handling some USB 3.0 devices.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2 years agokernel: generic: add missing 5.10 symbols
Rui Salvaterra [Thu, 24 Feb 2022 20:52:16 +0000 (20:52 +0000)]
kernel: generic: add missing 5.10 symbols

Add the following kconfig symbols (disabled):

CONFIG_DEFAULT_FQ
CONFIG_DEFAULT_CODEL
CONFIG_DEFAULT_SFQ

Also resort the config with the kconfig.pl script.

Fixes: f39872d966 ("kernel: generic: select the fq_codel qdisc by default")
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2 years agoipq806x: kernel crash log ramoops storage for R7800 and XR500
Hannu Nyman [Tue, 22 Feb 2022 18:11:23 +0000 (20:11 +0200)]
ipq806x: kernel crash log ramoops storage for R7800 and XR500

Define the kernel crash log storage ramoops/pstore feature
for R7800 and its sister XR500.

Reference to the ramoops admin guide in upstream Linux:
https://www.kernel.org/doc/html/v5.10/admin-guide/ramoops.html

Tested with R7800.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
2 years agokernel: package ramoops pstore-ram crash log storage
Hannu Nyman [Wed, 9 Feb 2022 21:54:47 +0000 (23:54 +0200)]
kernel: package ramoops pstore-ram crash log storage

Package the ability to log kernel crashes to 'ramoops' pstore
files into RAM in /sys/fs/pstore

Reference to the ramoops admin guide in upstream Linux:
https://www.kernel.org/doc/html/v5.10/admin-guide/ramoops.html

The files in RAM survive a warm reboot, but not a cold reboot.

Note: kmod-ramoops selects kmod-pstore and kmod-reed-solomon.

The feature can be used by selecting the kmod-ramoops and
adding a ramoops reserved-memory definition to the device DTS.
Example from R7800:

       reserved-memory {
                rsvd@5fe00000 {
                        reg = <0x5fe00000 0x200000>;
                        reusable;
                };

                ramoops@42100000 {
                        compatible = "ramoops";
                        reg = <0x42100000 0x40000>;
                        record-size = <0x4000>;
                        console-size = <0x4000>;
                        ftrace-size = <0x4000>;
                        pmsg-size = <0x4000>;
                };
        };

If no definition has been made in DTS, no crash log is stored
for the device.

Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(added CONFIG_EFI_VARS_PSTORE disable)

2 years agox86: grub2: search for the "kernel" filesystem on all disks
Jax Jiang [Thu, 10 Feb 2022 17:46:55 +0000 (01:46 +0800)]
x86: grub2: search for the "kernel" filesystem on all disks

Previously, grub2 was hardcoded to always look on "hd0" for the
kernel.

This works well when the system only had a single disk.
But if there was a second disk/stick present, it may have look
on the wrong drive because of enumeration races.

This patch utilizes grub2 search function to look for a filesystem
with the label "kernel". This works thanks to existing setup in
scripts/gen_image_generic.sh. Which sets the "kernel" label on
both the fat and ext4 filesystem variants.

Signed-off-by: Jax Jiang <jax.jiang.007@gmail.com>
Suggested-by: Alberto Bursi <bobafetthotmail@gmail.com> (MX100 WA)
(word wrapped, slightly rewritten commit message, removed MX100 WA)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agoRevert "bcm27xx: bcm27xx: update defconfig"
Christian Lamparter [Thu, 24 Feb 2022 16:21:42 +0000 (17:21 +0100)]
Revert "bcm27xx: bcm27xx: update defconfig"

This reverts all four commits
dbb45421bab "bcm27xx: bcm2708: update defconfig"
332f69583ad "bcm27xx: bcm2709: update defconfig"
a478202d74b "bcm27xx: bcm2710: update defconfig"
82da1dfd69a "bcm27xx: bcm2711: update defconfig"

this also highlighted an unrelated kconfig failure
that warrants investigation. But for now it is important
for the bcm27xx target to come back again.

|*
|* Restart config...
|*
|*
|* Allow override default queue discipline
|*
|Allow override default queue discipline (NET_SCH_DEFAULT) [Y/n/?] y
|  Default queuing discipline
|    1. Fair Queue (DEFAULT_FQ) (NEW)
|    2. Controlled Delay (DEFAULT_CODEL) (NEW)
|  > 3. Fair Queue Controlled Delay (DEFAULT_FQ_CODEL)
|    4. Stochastic Fair Queue (DEFAULT_SFQ) (NEW)
|    5. Priority FIFO Fast (DEFAULT_PFIFO_FAST)
|  choice[1-5?]:
|Error in reading or end of file.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agoat91: add support for sama7g5-ek board
Claudiu Beznea [Fri, 4 Feb 2022 14:17:03 +0000 (16:17 +0200)]
at91: add support for sama7g5-ek board

Add support for SAMA7G5-EK board.
Hardware:
- SoC: SAMA7G5
- RAM: Aliance Memory AS4C256M16D3LC (4 Gbit DDR3L)
- SD/MMC: 1 standard 4bit SD Card interface
- USB: 1 Micro-AB host/device, 1 Type-A host, 1 Type-C host
- CAN: 2 interfaces
- Ethernet: 10/100 port, 1Gbps port
- Wi-Fi/BT: 1 optional interface
- Audio: 1 SPDIF RX port, 1 SPDIF TX port, 4 digital microphones
- Camera: 1 RPi CSI camera interface
- Debug: 1 J-Link-OB + CDC, 1 JTAG
- LEDs: 1 RGB
- Buttons: 4 push buttons
- Expansions: 1 RPi Expansion connector, 2 mikroBUS connectors
- Power management: 1 power management IC, 1 power consumption
  measurement device

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2 years agoat91: add kernel support for sama7g5 soc
Claudiu Beznea [Fri, 4 Feb 2022 13:57:50 +0000 (15:57 +0200)]
at91: add kernel support for sama7g5 soc

Add kernel support for SAMA7G5 by back-porting mainline kernel patches.
Among SAMA7G5 features could be remembered:
- ARM Cortex-A7
- double data rate multi-port dynamic RAM controller supporting DDR2,
  DDR3, DDR3L, LPDDR2, LPDDR3 up to 533MHz
- peripherals for audio, video processing
- 1 gigabit + 1 megabit Ethernet controllers
- 6 CAN controllers
- trust zone support
- DVFS for CPU
- criptography IPs

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2 years agouboot-at91: update to linux4sam-2021.10
Claudiu Beznea [Fri, 4 Feb 2022 13:27:51 +0000 (15:27 +0200)]
uboot-at91: update to linux4sam-2021.10

Update uboot-at91 to linux4sam-2021.10 version.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2 years agoat91bootstrap: update to v3.10.4, v4.0.1
Claudiu Beznea [Fri, 4 Feb 2022 13:24:55 +0000 (15:24 +0200)]
at91bootstrap: update to v3.10.4, v4.0.1

AT91Bootstrap version 4 is available only for SAM9X60, SAMA5D2, SAMA5D3,
SAMA5D4, SAMA7G5. Thus use v4.0.1 for the above targets and v3.10.4 for
the rest of them. With the switch to v4 AT91Bootstrap binaries are now
on build/binaries. Take also this into account. Also, patches directory
is not needed anymore with the version update.

Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
2 years agobase-file: remove password aging feature form /etc/shadow
Rucke Teg [Tue, 22 Feb 2022 21:53:25 +0000 (22:53 +0100)]
base-file: remove password aging feature form /etc/shadow

In the default shadow file, as visible in the failsafe mode, the user
root has value of `0` set in  the 3rd field, the date of last password
change. This setting means that the password needs to be changed the
next time the user will log in the system. `dropbear` server is ignoring
this setting but `openssh-server` tries to enforce it and fails in the
failsafe mode because the rootfs is R/O.

Disable the password aging feature for user root by setting the 3rd
filed empty.

Signed-off-by: Rucke Teg <rucketeg@protonmail.com>
2 years agohostapd: SAE - Enable hunting-and-pecking and H2E
Nick Lowe [Mon, 21 Feb 2022 17:51:48 +0000 (17:51 +0000)]
hostapd: SAE - Enable hunting-and-pecking and H2E

Enable both the hunting-and-pecking loop and hash-to-element mechanisms
by default in OpenWRT with SAE.

Commercial Wi-Fi solutions increasingly frequently now ship with both
hunting-and-pecking and hash-to-element (H2E) enabled by default as this
is more secure and more performant than offering hunting-and-pecking
alone for H2E capable clients.

The hunting and pecking loop mechanism is inherently fragile and prone to
timing-based side channels in its design and is more computationally
intensive to perform. Hash-to-element (H2E) is its long-term
replacement to address these concerns.

For clients that only support the hunting-and-pecking loop mechanism,
this is still available to use by default.

For clients that in addition support, or were to require, the
hash-to-element (H2E) mechanism, this is then available for use.

Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
2 years agoCI: allow dots in commit subject area
Paul Spooren [Wed, 23 Feb 2022 18:51:43 +0000 (19:51 +0100)]
CI: allow dots in commit subject area

Due to a limited grep pattern, subjects containing dots like `image.mk`
were falsely reported as problematic. Extend pattern to allow dots.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agotools: use https for bc mirrors
Paul Spooren [Wed, 23 Feb 2022 21:34:25 +0000 (22:34 +0100)]
tools: use https for bc mirrors

All mirrors offer encrypted downloads, use it.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agomvebu: add targz feature flag
Paul Spooren [Wed, 23 Feb 2022 20:20:22 +0000 (21:20 +0100)]
mvebu: add targz feature flag

Adding the feature flag automatically creates a a rootfs.tar.gz files
which can be used for Docker rootfs containers.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agoRevert "scripts/diffconfig.sh: ensure config/conf is built"
Petr Štetiar [Thu, 24 Feb 2022 10:41:27 +0000 (11:41 +0100)]
Revert "scripts/diffconfig.sh: ensure config/conf is built"

This reverts commit c0849c1d9c17ba96a37b67363b5551c065e9f50d as it seems
to introduce regression in config.buildinfo files produced at least by
buildbots:

 $ curl -s https://downloads.openwrt.org/snapshots/targets/ath79/generic/config.buildinfo | head -2
 make[3]: Entering directory '/builder/shared-workdir/build'
 make[3]: Leaving directory '/builder/shared-workdir/build'

References: https://github.com/openwrt/openwrt/issues/9297#issuecomment-1049719381
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agowolfssl: fix API breakage of SSL_get_verify_result
Petr Štetiar [Tue, 22 Feb 2022 19:00:28 +0000 (20:00 +0100)]
wolfssl: fix API breakage of SSL_get_verify_result

Backport fix for API breakage of SSL_get_verify_result() introduced in
v5.1.1-stable.  In v4.8.1-stable SSL_get_verify_result() used to return
X509_V_OK when used on LE powered sites or other sites utilizing
relaxed/alternative cert chain validation feature. After an update to
v5.1.1-stable that API calls started returning X509_V_ERR_INVALID_CA
error and thus rendered all such connection attempts imposible:

 $ docker run -it openwrt/rootfs:x86_64-21.02.2 sh -c "wget https://letsencrypt.org"
 Downloading 'https://letsencrypt.org'
 Connecting to 18.159.128.50:443
 Connection error: Invalid SSL certificate

Fixes: #9283
References: https://github.com/wolfSSL/wolfssl/issues/4879
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agomediatek: mt7623: drop RAMFS_COPY_BIN
Daniel Golle [Tue, 22 Feb 2022 19:18:51 +0000 (19:18 +0000)]
mediatek: mt7623: drop RAMFS_COPY_BIN

fwtool is now always part of the sysupgrade stage2 ramdisk, so drop
the no longer needed RAMFS_COPY_BIN variable.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agomediatek: mt7622: drop RAMFS_COPY_BIN and RAMFS_COPY_DATA
Daniel Golle [Tue, 22 Feb 2022 18:50:25 +0000 (18:50 +0000)]
mediatek: mt7622: drop RAMFS_COPY_BIN and RAMFS_COPY_DATA

Now that both, fw_printenv/fw_setenv and fwtool are always present
during stage2 sysupgrade, we no longer need to list them in
RAMFS_COPY_BIN and RAMFS_COPY_DATA in platform.sh.
Drop both variables as they are now unneeded.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agobase-files: make sure tools are present in sysupgrade ramdisk
Daniel Golle [Tue, 22 Feb 2022 18:04:34 +0000 (18:04 +0000)]
base-files: make sure tools are present in sysupgrade ramdisk

Not all targets create /var/lock or touch /var/lock/fw_printenv.lock in
their platform.sh. This is problematic as fw_printenv then fails in
case /var/lock/fw_printenv.lock has not been created by previous calls
to fw_printenv/fw_setenv before sysupgrade is run.

Targets using fw_printenv/fw_setenv during sysupgrade:
 * ath79/*
 * ipq40xx/*
 * ipq806x/*
 * kirkwood/*
 * layerscape/*
 * mediatek/mt7622
 * mvebu/*
 * ramips/*
 * realtek/*

Targets currently using additional steps in /lib/upgrade/platform.sh
to make sure /var/lock/fw_printenv.lock (or at least /var/lock)
actually exists:
 * ath79/* (openmesh devices)
 * ipq40xx/* (linksys devices)
 * ipq806x/* (linksys devices)
 * kirkwood/* (linksys devices)
 * layerscape/*
 * mvebu/cortexa9 (linksys devices)

Given that accessing the U-Boot environment during sysupgrade is not
uncommon and the situation across targets is currently quite diverse,
just make sure both tools as well fw_env.config are always copied to
the ramdisk used for sysupgrade. Also make sure /var/lock always
exists.

This now allows to remove copying of fw_printenv/fw_setenv as well as
fw_env.config, creation of /var/lock or even /var/lock/fw_printenv.lock
from lib/upgrade/platform.sh or files included there.

As the same applies also to 'fwtool' which is used by generic eMMC
sysupgrade, also always copy that to ramdisk.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agoscripts/diffconfig.sh: ensure config/conf is built
Eneas U de Queiroz [Mon, 21 Feb 2022 17:44:43 +0000 (14:44 -0300)]
scripts/diffconfig.sh: ensure config/conf is built

diffconfig.sh runs ./scripts/config/conf, but it does not get built
with 'make {menu,x,n}config.  Call 'make ./scripts/config/conf' to
ensure it's been built befpre running it.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2 years agobuild: toplevel.mk: fix missing kconfig dependency tracking
Petr Štetiar [Mon, 21 Feb 2022 10:50:39 +0000 (11:50 +0100)]
build: toplevel.mk: fix missing kconfig dependency tracking

Toplevel Make is not aware about changes in the `scripts/config/*conf`
targets and this is causing issues for during update to that part of
build tree, where one needs to handle this manually by either force
rebuilding the targets or running `make config-clean`. Fix this by
forcing the rebuild if necessary.

Fixes: #9297
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agoopenssl: configure engines with uci
Eneas U de Queiroz [Mon, 21 Feb 2022 00:09:30 +0000 (21:09 -0300)]
openssl: configure engines with uci

This uses uci to configure engines, by generating a list of enabled
engines in /var/etc/ssl/engines.cnf from engines configured in
/etc/config/openssl:

    config engine 'devcrypto'
            option enabled '1'

Currently the only options implemented are 'enabled', which defaults to
true and enables the named engine, and the 'force' option, that enables
the engine even if the init script thinks the engine does not exist.

The existence test is to check for either a configuration file
/etc/ssl/engines.cnf.d/%ENGINE%.cnf, or a shared object file
/usr/lib/engines-1.1/%ENGINE%.so.

The engine list is generated by an init script which is set to run after
'log' because it informs the engines being enabled or skipped.  It
should run before any service using OpenSSL as the crypto library,
otherwise the service will not use any engine.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2 years agoopenssl: configure engine packages during install
Eneas U de Queiroz [Mon, 21 Feb 2022 00:09:29 +0000 (21:09 -0300)]
openssl: configure engine packages during install

This enables an engine during its package's installation, by adding it
to the engines list in /etc/ssl/engines.cnf.d/engines.cnf.

The engine build system was reworked, with the addition of an engine.mk
file that groups some of the engine packages' definitions, and could be
used by out of tree engines as well.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2 years agoopenssl: config engines in /etc/ssl/engines.cnf.d
Eneas U de Queiroz [Mon, 21 Feb 2022 00:09:28 +0000 (21:09 -0300)]
openssl: config engines in /etc/ssl/engines.cnf.d

This changes the configuration of engines from the global openssl.cnf to
files in the /etc/ssl/engines.cnf.d directory.  The engines.cnf file has
the list of enabled engines, while each engine has its own configuration
file installed under /etc/ssl/engines.cnf.d.

Patches were refreshed with --zero-commit.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2 years agoath79: image: use 'kmod-usb-chipidea2' for AR933x devices
Piotr Dymacz [Mon, 21 Feb 2022 21:15:45 +0000 (22:15 +0100)]
ath79: image: use 'kmod-usb-chipidea2' for AR933x devices

AR933x based devices should include 'kmod-usb-chipidea2' for USB
support. Fixes: #9243.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agoath79: image: drop 'BOARDNAME' from devices recipes
Piotr Dymacz [Sun, 20 Feb 2022 11:43:38 +0000 (12:43 +0100)]
ath79: image: drop 'BOARDNAME' from devices recipes

The 'BOARDNAME' variable is part of target configuration and shouldn't
be part of a device's image recipe.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2 years agoqosify: update to the latest version
Felix Fietkau [Sun, 20 Feb 2022 17:13:02 +0000 (18:13 +0100)]
qosify: update to the latest version

65b42032063f interface: add missing autorate-ingress options

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agorealtek: remove debugging code from timer
Sander Vanheule [Sun, 20 Feb 2022 16:17:18 +0000 (17:17 +0100)]
realtek: remove debugging code from timer

Remove some (dead) debugging code from the Realtek timer to clean up the
sources of this driver.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2 years agorealtek: use DT provided address for timers
Sander Vanheule [Sun, 20 Feb 2022 16:17:17 +0000 (17:17 +0100)]
realtek: use DT provided address for timers

The I/O base address for the timers was hardcoded into the driver,
or derived from the HW IRQ number as an even more horrible hack. All
supported SoC families have these timers, but with hardcoded addresses
the code cannot be reused right now.

Request the timer's base address from the DT specification, and store it
in a private struct for future reference.

Matching the second interrupt specifier, the address range for the
second timer is added to the DT specification.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2 years agorealtek: clean up RTL930x timer DT node
Sander Vanheule [Sun, 20 Feb 2022 16:17:16 +0000 (17:17 +0100)]
realtek: clean up RTL930x timer DT node

The Realtek timer node for RTL930x doesn't have any child nodes, making
the use of '#address-cells' quite pointless. It is also not an interrupt
controller, meaning it makes no sense to define '#interrupt-cells'.

The I/O address for this node is also wrong, but this is hidden by the
fact that the driver associated with this node bypasses the usual DT
machinery and does it's own thing. Correct the address to have a sane
value, even though it isn't actually used.

Fixes: a75b9e3ecb61 ("realtek: Adding RTL930X sub-target")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2 years agorealtek: ZyXEL GS1900-48: fix system LED polarity
Sander Vanheule [Sun, 20 Feb 2022 15:25:45 +0000 (16:25 +0100)]
realtek: ZyXEL GS1900-48: fix system LED polarity

When driven by a GPIO pin, the system LED needs to be configured as
active high. Otherwise the LED switches off after booting and
initialisation.

Fixes: 47f5a0a3eed5 ("realtek: Add support for ZyXEL GS1900-48 Switch")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2 years agorealtek: ZyXEL GS1900-48: drop status from gpio1
Sander Vanheule [Sun, 20 Feb 2022 15:25:44 +0000 (16:25 +0100)]
realtek: ZyXEL GS1900-48: drop status from gpio1

The default value for a DT node's status property is already "okay", so
there's no need to specify it again. Drop the status property to clean
up the DTS.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2 years agorealtek: use higher priority for timer interrupts
Sander Vanheule [Sun, 20 Feb 2022 15:25:43 +0000 (16:25 +0100)]
realtek: use higher priority for timer interrupts

The assigned output index for the event timers was quite low, lower even
than the ethernet interrupt. This means that high network load could
preempt timer interrupts, possibly leading to all sorts of strange
behaviour.

Increase the interrupt output index of the event timers to 5, which is
the highest priority output and corresponds to the (otherwise unused)
MIPS CPU timer interrupt.

Fixes: a75b9e3ecb61 ("realtek: Adding RTL930X sub-target")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2 years agorealtek: move RTL8231 definitions to board files
Sander Vanheule [Sun, 20 Feb 2022 15:25:42 +0000 (16:25 +0100)]
realtek: move RTL8231 definitions to board files

The RTL8231 is an external chip, and not part of the SoC. That means
it is more appropriate to define it in the board specific (base) files,
instead of the DT include for the SoC itself.

Moving the RTL8231 definition also ensures that boards with no GPIO
expander, or an alternative one, don't have a useless gpio1 node label
defined.

Tested on a Netgear GS110TPPv1.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
2 years agorealtek: fix node addresses for RTL839x
Sander Vanheule [Sun, 20 Feb 2022 15:25:41 +0000 (16:25 +0100)]
realtek: fix node addresses for RTL839x

The address in some node names doesn't match the actual offset specified
in the DT node. Update the names to fix this.

While fixing the node names, also drop the unused node labels.

Fixes: 0a7565e53653 ("realtek: Update rtl839x.dtsi for realtek,rtl-intc, new gpio controller remove RTL8231 node")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2 years agorealtek: consolidate bootargs again
Sander Vanheule [Sun, 20 Feb 2022 15:25:40 +0000 (16:25 +0100)]
realtek: consolidate bootargs again

Bootargs for devices in the realtek target were previously consolidated
in commit af2cfbda2bf5 ("realtek: Consolidate bootargs"), since all
devices currently use the same arguments.

Commit a75b9e3ecb61 ("realtek: Adding RTL930X sub-target") reverted this
without any argumentation, so let's undo that.

Commit 0b8dfe085180 ("realtek: Add RTL931X sub-target") introduced the
old bootargs also for RTL931x, without providing any actual device
support. Until that is done, let's assume vendors will have done what
they did before, and use a baud rate of 115200.

Fixes: a75b9e3ecb61 ("realtek: Adding RTL930X sub-target")
Signed-off-by: Sander Vanheule <sander@svanheule.net>
2 years agomvebu: cortexa72: enable ARM_ARMADA_8K_CPUFREQ
Matthew Hagan [Thu, 17 Feb 2022 00:04:32 +0000 (00:04 +0000)]
mvebu: cortexa72: enable ARM_ARMADA_8K_CPUFREQ

Enable the AP806's cpufreq driver. This driver is compatible with the
Armada 7K and 8K platforms.

Tested-by: Stijn Segers <foss@volatilesystems.org> (RB5009UG+S+IN)
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
2 years agouboot-mvebu: backport pending patches for Marvell A38x
Josef Schlehofer [Thu, 17 Feb 2022 09:01:29 +0000 (10:01 +0100)]
uboot-mvebu: backport pending patches for Marvell A38x

100-ddr-marvell-a38x-fix-BYTE_HOMOGENEOUS_SPLIT_OUT-deci.patch [1]:
SoC Marvell A38x is used in Turris Omnia, and we thought that with recent
fiddling around DDR training to fix it once for all, there were
reproduced the issue in the upcoming new revision Turris Omnia boards.

101-arm-mvebu-spl-Add-option-to-reset-the-board-on-DDR-t.patch [2]:
This is useful when some board may occasionally fail with DDR training,
and it adds the option to reset the board on the DDR training failure

102-arm-mvebu-turris_omnia-Reset-the-board-immediately-o.patch [3]:
This enables the option CONFIG_DDR_RESET_ON_TRAINING_FAILURE (added by
101 patch), so the Turris Omnia board is restarted immediately, and it
does not require to reset the board manually or wait 120s for MCU to
reset the board

[1] https://patchwork.ozlabs.org/project/uboot/patch/20220217000837.13003-1-kabel@kernel.org/
[2] https://patchwork.ozlabs.org/project/uboot/patch/20220217000849.13028-1-kabel@kernel.org/
[3] https://patchwork.ozlabs.org/project/uboot/patch/20220217000849.13028-2-kabel@kernel.org/

Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
2 years agobcm27xx: bcm2711: update defconfig
John Audia [Wed, 9 Feb 2022 11:18:44 +0000 (06:18 -0500)]
bcm27xx: bcm2711: update defconfig

Enabled CONFIG_ALL_KMODS and ran make kernel_menuconfig against
bcm2711 to update defconfig.  Some of the removed symbols are
present in target/linux/generic/config-5.10 while others were
removed by the make target.

Signed-off-by: John Audia <graysky@archlinux.us>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (wrapped)
2 years agobcm27xx: bcm2710: update defconfig
John Audia [Wed, 9 Feb 2022 11:30:14 +0000 (06:30 -0500)]
bcm27xx: bcm2710: update defconfig

Enabled CONFIG_ALL_KMODS and ran make kernel_menuconfig against
bcm2710 to update defconfig.  Some of the removed symbols are
present in target/linux/generic/config-5.10 while others were
removed by the make target.

Signed-off-by: John Audia <graysky@archlinux.us>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (wrapped)
2 years agobcm27xx: bcm2709: update defconfig
John Audia [Wed, 9 Feb 2022 11:34:20 +0000 (06:34 -0500)]
bcm27xx: bcm2709: update defconfig

Enabled CONFIG_ALL_KMODS and ran make kernel_menuconfig against
bcm2709 to update defconfig.  Some of the removed symbols are
present in target/linux/generic/config-5.10 while others were
removed by the make target.

Signed-off-by: John Audia <graysky@archlinux.us>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (wrapped)
2 years agobcm27xx: bcm2708: update defconfig
John Audia [Wed, 9 Feb 2022 11:39:05 +0000 (06:39 -0500)]
bcm27xx: bcm2708: update defconfig

Enabled CONFIG_ALL_KMODS and ran make kernel_menuconfig against
bcm2708 to update defconfig.  Some of the removed symbols are
present in target/linux/generic/config-5.10 while others were
removed by the make target.

Signed-off-by: John Audia <graysky@archlinux.us>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (wrapped)
2 years agomac80211: add debug compile option for rtw88 devices
Florian Eckert [Tue, 1 Feb 2022 12:37:24 +0000 (13:37 +0100)]
mac80211: add debug compile option for rtw88 devices

This commit adds the following package compile options.

CONFIG_PACKAGE_RTW88_DEBGUG:
Compile the driver with additional debug logging output

CONFIG_PACKAGE_RTW88_DEBGUGFS:
Add the possibility to map information about the driver rtw88 into
debugfs.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
2 years agoipq40xx: mikrotik: fix LED script
Robert Marko [Sun, 20 Feb 2022 11:39:26 +0000 (12:39 +0100)]
ipq40xx: mikrotik: fix LED script

Fix the missing ;; after the cAP ac case in /e/b/01_leds.

Fixes: 93d9119 ("ipq40xx: add MikroTik cAP ac support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (minor touch-up)
2 years agoath79: uboot-envtools: fix partition for ZTE MF286
Lech Perczak [Thu, 17 Feb 2022 20:47:23 +0000 (21:47 +0100)]
ath79: uboot-envtools: fix partition for ZTE MF286

By mistake, a wrong partition for U-boot environment was introduced for
ZTE MF286 while adding support, when flash layout wasn't finalized. Fix
that, according to the actual flash layout:
dev:    size   erasesize  name
mtd0: 00140000 00020000 "fota-flag"
mtd1: 00140000 00020000 "caldata"
mtd2: 00140000 00020000 "mac"
mtd3: 00f40000 00020000 "ubiconcat0"
mtd4: 00400000 00020000 "kernel"
mtd5: 06900000 00020000 "ubiconcat1"
mtd6: 00080000 00010000 "u-boot"
mtd7: 00020000 00010000 "u-boot-env"
mtd8: 07840000 00020000 "ubi"

Fixes: 8c78a13bfc1f ("ath79: support ZTE MF286")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
2 years agoipq806x: disable Linksys EA7500v1 and EA8500
Christian Lamparter [Sat, 19 Feb 2022 19:26:01 +0000 (20:26 +0100)]
ipq806x: disable Linksys EA7500v1 and EA8500

The kernel of both images will no longer fit into
the 3072KiB / 3MiB kernel partition:
|Image Name:   ARM OpenWrt Linux-5.10.100
|Created:      Sat Feb 19 00:11:55 2022
|Image Type:   ARM Linux Kernel Image (uncompressed)
|Data Size:    3147140 Bytes = 3073.38 KiB = 3.00 MiB

Disable both targets for now, until a solution is available.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agompc85xx: fix KEY_RFKILL vs KEY_RFKill
Christian Lamparter [Sat, 19 Feb 2022 22:09:34 +0000 (23:09 +0100)]
mpc85xx: fix KEY_RFKILL vs KEY_RFKill

This fixes a buildbot builder error:
Error: arch/powerpc/boot/dts/tl-wdr4900-v1.dts:245.18-19 syntax error

Fixes: 256e1dbc7d09 ("mpc85xx: utilize dt-binding definitions for keys + gpios")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agonetifd: bump to version 2022-02-20
Petr Štetiar [Sun, 20 Feb 2022 09:51:04 +0000 (10:51 +0100)]
netifd: bump to version 2022-02-20

Contains following changes:

 136006b88826 cmake: fix usage of implicit library and include paths
 bc0e84d689e2 netifd: interface-ip: don't set fib6 policies if ipv6 disabled

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agoramips: clean up Makefile formatting
Nick McKinney [Thu, 13 Jan 2022 20:56:37 +0000 (15:56 -0500)]
ramips: clean up Makefile formatting

Use correct indent in target/linux/ramips/image/mt7621.mk
to be consistent with the rest of the file.

Signed-off-by: Nick McKinney <nick@ndmckinney.net>
[rephrase commit message as Adrian suggested, fix a6004ns-m indent]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2 years agoramips: mt7621: print size of factory initramfs-image if it's too big
Sven Roederer [Tue, 20 Jul 2021 23:30:41 +0000 (01:30 +0200)]
ramips: mt7621: print size of factory initramfs-image if it's too big

It's helpful to know the current and maximal size of the imagefiles if the
creation fails.

Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
2 years agoath79: fix wndr4500v3 lan port order to match case
Graham Cole [Sun, 20 Feb 2022 02:45:01 +0000 (21:45 -0500)]
ath79: fix wndr4500v3 lan port order to match case

The LED and LAN port numbering on the case of wndr4500v3 devices are
reversed relative to the wndr4300v2. I created this patch to so that the
ordering in OpenWRT will be consistent with that.

Signed-off-by: Graham Cole <diakka@gmail.com>
2 years agoramips: add support for ipTIME A3002MESH
Yoonji Park [Fri, 11 Feb 2022 14:18:39 +0000 (23:18 +0900)]
ramips: add support for ipTIME A3002MESH

Add support for ipTIME A3002MESH.

Hardware:
- SoC: MediaTek MT7621AT (880MHz, Duel-Core)
- RAM: DDR3 128MB
- Flash: XMC XM25QH128AHIG (SPI-NOR 16MB)
- WiFi: MediaTek MT7615D (2.4GHz, 5GHz, DBDC)
- Ethernet: MediaTek MT7530 (WAN x1, LAN x2, SoC built-in)
- UART: [GND, RX, TX, 3.3V] (57600 8N1, J4)

MAC addresses:
| interface |        MAC        |     source     | comment
|-----------|-------------------|----------------|----------
|       LAN | 70:XX:XX:5X:XX:X3 |                |
|       WAN | 70:XX:XX:5X:XX:X1 | u-boot 0x1fc40 |
|   WLAN 2G | 72:XX:XX:4X:XX:X0 |                |
|   WLAN 5G | 70:XX:XX:5X:XX:X0 | factory 0x4    |
|           | 70:XX:XX:5X:XX:X0 | u-boot 0x1fc20 | unknown
|           | 70:XX:XX:5X:XX:X2 | factory 0x8004 | unknown

- WLAN 2G MAC address is not the same as stock firmware since OpenWrt
  uses LAN MAC address with local bit sets.

Installation:
1. Flash initramfs image. This can be done using stock web ui or TFTP
2. Connect to OpenWrt with an SSH connection to 192.168.1.1
3. Perform sysupgrade with sysupgrade image

Revert to stock firmware:
- Flash stock firmware via OEM TFTP Recovery mode
- Perform sysupgrade with stock image

TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1

Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
[wrap/rephrase commit message]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2 years agoRevert "ramips: increase spi-max-frequency for ipTIME mt7620 devices"
Sungbo Eo [Sat, 19 Feb 2022 15:19:31 +0000 (00:19 +0900)]
Revert "ramips: increase spi-max-frequency for ipTIME mt7620 devices"

This reverts commit 13a185bf8acb67da4a68873e560876c0e60b1a87.

There was a report that one A1004ns device fails to detect its flash
chip correctly:

[    1.470297] spi-nor spi0.0: unrecognized JEDEC id bytes: e0 10 0c 40 10 08
[    1.484110] spi-nor: probe of spi0.0 failed with error -2

It also uses a different flash chip model:
* in my hand: Winbond W25Q128FVSIG (SOIC-8)
* reported: Macronix MX25L12845EMI-10G (SOP-16)

Reducing spi-max-frequency solved the detection failure. Hence revert.

Reported-by: Koasing <koasing@gmail.com>
Tested-by: Koasing <koasing@gmail.com>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2 years agowireless-regdb: update to version 2022.02.18
Sungbo Eo [Sat, 19 Feb 2022 01:46:01 +0000 (10:46 +0900)]
wireless-regdb: update to version 2022.02.18

e061299 wireless-regdb: Raise DFS TX power limit to 250 mW (24 dBm) for the US
2ce78ed wireless-regdb: Update regulatory rules for Croatia (HR) on 6GHz
0d39f4c wireless-regdb: Update regulatory rules for South Korea (KR)
acad231 wireless-regdb: Update regulatory rules for France (FR) on 6 and 60 GHz
ea83a82 wireless-regdb: add support for US S1G channels
4408149 wireless-regdb: add 802.11ah bands to world regulatory domain
5f3cadc wireless-regdb: Update regulatory rules for Spain (ES) on 6GHz
e0ac69b Revert "wireless-regdb: Update regulatory rules for South Korea (KR)"
40e5e80 wireless-regdb: Update regulatory rules for South Korea (KR)
e427ff2 wireless-regdb: Update regulatory rules for China (CN)
0970116 wireless-regdb: Update regulatory rules for the Netherlands (NL) on 6GHz
4dac44b wireless-regdb: update regulatory database based on preceding changes

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2 years agoath79: utilize nvmem on Netgear EX7300 v2
Sungbo Eo [Tue, 8 Feb 2022 16:32:47 +0000 (01:32 +0900)]
ath79: utilize nvmem on Netgear EX7300 v2

mtd-mac-address should no longer be used after commit 5ae2e786395c
("kernel: drop support for mtd-mac-address"). Convert it to nvmem-cells.

While at it, also convert OpenWrt's custom mtd-cal-data property and
userspace pre-calibration data extraction to the nvmem implementation.

Note: nvmem-cells in QCN5502 wmac has not been tested.

Fixes: c32008a37b81 ("ath79: add partial support for Netgear EX7300v2")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2 years agoapm821xx: WNDR4700: use upstream tc654 cooling devices
Christian Lamparter [Sat, 12 Feb 2022 18:53:37 +0000 (19:53 +0100)]
apm821xx: WNDR4700: use upstream tc654 cooling devices

Upstream hwmon-maintainer had various comments about
the changes to the tc654 driver. These have been
addressed and the cooling device support is destined
for inclusion.

One of the comments was the change of the cooling states
scaling. No longer the driver uses the same values as the
hwmon interface, instead the states are now the 17 states
the tc654 supports.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agokernel: add kmod-hwmon-lm70 support
Christian Lamparter [Thu, 17 Feb 2022 15:10:42 +0000 (16:10 +0100)]
kernel: add kmod-hwmon-lm70 support

package hwmon's lm70.ko. This module supports the
National Semiconductor/TI LM70,LM71,LM74 and
TI TMP121,TMP122,TMP123 and TMP124 chips (all SPI).

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agompc85xx: add HiveAP-350 alternative name for HiveAP-330
Christian Lamparter [Sun, 13 Feb 2022 12:11:56 +0000 (13:11 +0100)]
mpc85xx: add HiveAP-350 alternative name for HiveAP-330

The HiveAP-350 has six external antennas connectors.
(It also has twice the flash?)

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agompc85xx: utilize dt-binding definitions for keys + gpios
Christian Lamparter [Sun, 13 Feb 2022 12:14:03 +0000 (13:14 +0100)]
mpc85xx: utilize dt-binding definitions for keys + gpios

include the device-tree binding headers that provide definitions
for keys codes and gpios in the device-tree files.

Random bonus: merge tl-wdr4900-v1's uboot with the nvmem-node.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agompc85xx: change legacy "eeprom" compatible
Christian Lamparter [Sun, 13 Feb 2022 11:46:37 +0000 (12:46 +0100)]
mpc85xx: change legacy "eeprom" compatible

silences the following message:
> eeprom 0-0051: eeprom driver is deprecated, please use at24 instead

The chip was likely a Dallas Semiconductor and later MAXIM part
before Analog Devices, Inc. bought MAXIM.

From the datasheet:

"The DS28CN01 combines 1024 bits of EEPROM with challenge-and-response
authentication security implemented with the FIPS 180-1/180-2 and
ISO/IEC 10118-3 Secure Hash Algorithm (SHA-1)."

...

"Write Access Requires Knowledge of the Secret
and the Capability of Computing and Transmitting
a 160-Bit MAC as Authorization"

OpenWrt doesn't use it. There's no in-kernel driver
from what I know. Let's document that the chip is
at the location.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agompc85xx: update lp5521 led-controller node for 5.10
Christian Lamparter [Sun, 13 Feb 2022 10:18:04 +0000 (11:18 +0100)]
mpc85xx: update lp5521 led-controller node for 5.10

The tricolor LED which is controlled by a lp5521 needed
some maintenance as the driver failed to load in the
current v5.10 image:
| lp5521: probe of 0-0032 failed with error -22

This is because the device-tree needed to be updated
to match the latest led coloring and function trends.

 - removed the device name from the label
 - added color/function properties
 - added required reg and cells properties

For reference a disabled multicolor/RGB is added since this
reflects the real hardware. Unfortunately, the multicolor
sysfs interface isn't supported by yet.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agompc85xx: Patch HiveAP 330 u-boot to fix boot
Martin Kennedy [Wed, 22 Dec 2021 18:08:33 +0000 (13:08 -0500)]
mpc85xx: Patch HiveAP 330 u-boot to fix boot

When Kernel 5.10 was enabled for mpc85xx, the kernel once again became too
large upon decompression (>7MB or so) to decompress itself on boot (see
FS#4110[1]).

There have been many attempts to fix booting from a compressed kernel on
the HiveAP-330:

b683f1c36d8a ("mpc85xx: Use gzip compressed kernel on HiveAP-330")
98089bb8ba82 ("mpc85xx: Use uncompressed kernel on the HiveAP-330")
26cb167a5ca7 ("mpc85xx: Fix Aerohive HiveAP-330 initramfs image")

We can no longer compress the kernel due to size, and the stock bootloader
does not support any other types of compression. Since an uncompressed
kernel no longer fits in the 8MiB kernel partition at 0x2840000, we need to
patch u-boot to autoboot by running variable which isn't set by the
bootloader on each autoboot.

This commit repartitions the HiveAP, requiring a new COMPAT_VERSION,
and uses the DEVICE_COMPAT_MESSAGE to guide the user to patch u-boot,
which changes the variable run on boot to be `owrt_boot`; the user can
then set the value of that variable appropriately.

The following has been documented in the device's OpenWrt wiki page:
<https://openwrt.org/toh/aerohive/hiveap-330>. Please look there
first/too for more information.

The from-stock and upgrade from a previous installation now becomes:

0) setup a network with a dhcp server and a tftp server at serverip
(192.168.1.101) with the initramfs image in the servers root directory.

1) Hook into UART (9600 baud) and enter U-Boot. You may need to enter
a password of administrator or AhNf?d@ta06 if prompted. If the password
doesn't work. Try reseting the device by pressing and holding the reset
button with the stock OS.

2) Once in U-Boot, set the new owrt_boot and tftp+boot the initramfs image:
   Use copy and paste!

 # fw_setenv owrt_boot 'setenv bootargs \"console=ttyS0,$baudrate\";bootm 0xEC040000 - 0xEC000000'
 # save
 # dhcp
 # setenv bootargs console=ttyS0,$baudrate
 # tftpboot 0x1000000 192.168.1.101:openwrt-mpc85xx-p1020-aerohive_hiveap-330-initramfs-kernel.bin
 # bootm

3) Once openwrt booted:
carefully copy and paste this into the root shell. One step at a time

  # 3.0 install kmod-mtd-rw from the internet and load it

  opkg update; opkg install kmod-mtd-rw
  insmod mtd-rw i_want_a_brick=y

  # 3.1 create scripts that modifies uboot

cat <<- "EOF" > /tmp/uboot-update.sh
  . /lib/functions/system.sh
  cp "/dev/mtd$(find_mtd_index 'u-boot')" /tmp/uboot
  cp /tmp/uboot /tmp/uboot_patched
  ofs=$(strings -n80 -td < /tmp/uboot | grep '^ [0-9]* setenv bootargs.*cp\.l' | cut -f2 -d' ')
  for off in $ofs; do
    printf "run owrt_boot;            " | dd of=/tmp/uboot_patched bs=1 seek=${off} conv=notrunc
  done
  md5sum /tmp/uboot*
EOF

  # 3.2 run the script to do the modification

  sh /tmp/uboot-update.sh

  # verify that /tmp/uboot and /tmp/uboot_patched are good
  #
  # my uboot was: (is printed during boot)
  # U-Boot 2009.11 (Jan 12 2017 - 00:27:25), Build: jenkins-HiveOS-Honolulu_AP350_Rel-245
  #
  # d84b45a2e8aca60d630fbd422efc6b39  /tmp/uboot
  # 6dc420f24c2028b9cf7f0c62c0c7f692  /tmp/uboot_patched
  # 98ebc7e7480ce9148cd2799357a844b0  /tmp/uboot-update.sh <-- just for reference

  # 3.3 this produces the /tmp/u-boot_patched file.

  mtd write /tmp/uboot_patched u-boot

3) scp over the sysupgrade file to /tmp/ and run sysupgrade to flash OpenWrt:

  sysupgrade -n /tmp/openwrt-mpc85xx-p1020-aerohive_hiveap-330-squashfs-sysupgrade.bin

4) after the reboot, you are good to go.

Other notes:

- Note that after this sysupgrade, the AP will be unavailable for 7 minutes
  to reformat flash. The tri-color LED does not blink in any way to
  indicate this, though there is no risk in interrupting this process,
  other than the jffs2 reformat being reset.

- Add a uci-default to fix the compat version. This will prevent updates
  from previous versions without going through the installation process.

- Enable CONFIG_MTD_SPLIT_UIMAGE_FW and adjust partitioning to combine
  the kernel and rootfs into a single dts partition to maximize storage
  space, though in practice the kernel can grow no larger than 16MiB due
  to constraints of the older mpc85xx u-boot platform.

- Because of that limit, KERNEL_SIZE has been raised to 16m.

- A .tar.gz of the u-boot source for the AP330 (a.k.a. Goldengate) can
  be found here[2].

- The stock-jffs2 partition is also removed to make more space -- this
  is possible only now that it is no longer split away from the rootfs.

- the console-override is gone. The device will now get the console
  through the bootargs. This has the advantage that you can set a different
  baudrate in uboot and the linux kernel will stick with it!

- due to the repartitioning, the partition layout and names got a makeover.

- the initramfs+fdt method is now combined into a MultiImage initramfs.
  The separate fdt download is no longer needed.

- added uboot-envtools to the mpc85xx target. All targets have uboot and
  this way its available in the initramfs.

[1]: https://bugs.openwrt.org/index.php?do=details&task_id=4110
[2]: magnet:?xt=urn:btih:e53b27006979afb632af5935fa0f2affaa822a59

Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
(rewrote parts of the commit message, Initramfs-MultiImage,
dropped bootargs-override, added wiki entry + link, uboot-envtools)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agoksmbd: add out-of-tree module
Rosen Penev [Tue, 21 Dec 2021 01:58:38 +0000 (17:58 -0800)]
ksmbd: add out-of-tree module

ksmbd is an upstream linux alternative to Samba which is lighterweight
and more performant, especially on underpowered devices.

Moving it here from the packages feed as it is now an upstream kernel
module. Also easier to update as version updates can be coordinated better

The next LTS kernel (5.15) has this included. A depend on kernel < 5.15
will need to be added later.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2 years agolinux/modules: split up oid_registry
Rosen Penev [Thu, 10 Feb 2022 02:58:29 +0000 (18:58 -0800)]
linux/modules: split up oid_registry

This will be needed by ksmbd in a following commit.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2 years agotarget/linux: add help text to kernel config
Rosen Penev [Thu, 10 Feb 2022 02:46:15 +0000 (18:46 -0800)]
target/linux: add help text to kernel config

These options will be used for ksmbd. Once kernel 5.15
makes it in, this patch can go away.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2 years agox86: fix support for Sophos SG/XG wireless products
Raylynn Knight [Thu, 10 Feb 2022 07:25:27 +0000 (02:25 -0500)]
x86: fix support for Sophos SG/XG wireless products

Correct typo that caused network interfaces for Sophos
SG/XG wireless devices to not be configured properly.

Tested on Sophos SG 135wr2, Sophos XG 125wr2 and
Sophos SG 105wr1

Signed-off-by: Raylynn Knight <rayknight@me.com>
2 years agomvebu: mark all mtd partitions on GL.iNet GL-MV1000 read-only
Enrico Mioso [Thu, 10 Feb 2022 13:35:49 +0000 (14:35 +0100)]
mvebu: mark all mtd partitions on GL.iNet GL-MV1000 read-only

On this device, two of the three defined MTD partitions are
automatically set to read-only, since they do not end at an
erase/write block boundary.

In particular, the only partition remaining writable is the
one holding the u-boot bootloader.

Mark all of the partitions read-only, at least until a better
understanding of why the layout has been laid out this way is
gained.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2 years agoipq806x: update defconfig
John Audia [Wed, 9 Feb 2022 21:01:01 +0000 (16:01 -0500)]
ipq806x: update defconfig

Enabled `CONFIG_ALL_KMODS` and ran `make kernel_menuconfig` against
ipq806x to update defconfig.

The removed symbols are in fact present in
target/linux/generic/config-5.10. CONFIG_MDIO_DEVRES
was likely added due to this:
<https://elixir.bootlin.com/linux/v5.10.100/source/drivers/net/phy/Kconfig#L16>

Signed-off-by: John Audia <graysky@archlinux.us>
2 years agoipq806x: TP-Link VR2600v convert legacy partitioning
Christian Lamparter [Sun, 6 Feb 2022 16:21:08 +0000 (17:21 +0100)]
ipq806x: TP-Link VR2600v convert legacy partitioning

This device still had the legacy flash partitioning.
This is a problem, because neither the nvmem-cells
for mac-address and calibration. Nor the denx,uimage
mtd-splitter compatible would be picked up.

The patch also changes the node-names of the flash
and partition nodes to hopefully meet all the
current FDT trends.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agoipq40xx: document pcie wifi chip on the GL.Inet GL-B2200
Christian Lamparter [Mon, 14 Feb 2022 20:14:34 +0000 (21:14 +0100)]
ipq40xx: document pcie wifi chip on the GL.Inet GL-B2200

Enrico provided a bootlog that shows the chip is a WAVE-2 QCA9888v2:

> pci 0000:01:00.0: [168c:0056] type 00 class 0x028000
> [...]
> ath10k 5.15 driver, optimized for CT firmware, probing pci device: 0x56.
> ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 [...] chip_id 0x00000000 sub 0000:0000
> ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9888-fW-13-5ae337bb1 api 5  features mfp,[...]
> ath10k_pci 0000:01:00.0: board_file api 2 bmi_id N/A crc32 6535d835
> ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal file max-sta 32 raw 0 hwcrypto 1

this patch switches the device over to pre-calibration.
(this is more or less cosmetic)

Reported-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agoipq40xx: limit available radio channels for GL.iNet GL-B2200
Enrico Mioso [Fri, 11 Feb 2022 09:46:00 +0000 (10:46 +0100)]
ipq40xx: limit available radio channels for GL.iNet GL-B2200

The PCIe and built-in 5GHZ radios are meant to operate on different
frequency bands. The hardware enforces this via RF filters.
Add this information to allow software enforcing it as well.
Credits to Piotr Dymacz for the invaluable help.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2 years agoapm821xx: add alternative names for supported devices
Christian Lamparter [Sun, 13 Feb 2022 12:29:23 +0000 (13:29 +0100)]
apm821xx: add alternative names for supported devices

with the introduction of the DEVICE_ALTX_VENDOR, DEVICE_ALTX_MODEL
multiple/sibiling devices can seemingly supported by one device entry.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2 years agoramips: add Ubiquiti EdgePoint R6 as alt name
Nick Hainke [Sat, 19 Feb 2022 07:35:10 +0000 (08:35 +0100)]
ramips: add Ubiquiti EdgePoint R6 as alt name

The Ubiquiti EdgePoint R6 is identical to the EdgeRouter X SFP.
However, it fits well into outdoor environments due to its water-proven
case.

More specifications: 9715beb04c74 ("ramips: add support for Ubiquiti
EdgeRouter X-SFP")

Signed-off-by: Nick Hainke <vincent@systemli.org>
2 years agohostapd: fallback to psk when generating r0kh/r1kh
Eneas U de Queiroz [Fri, 7 Jan 2022 20:19:36 +0000 (17:19 -0300)]
hostapd: fallback to psk when generating r0kh/r1kh

The 80211r r0kh and r1kh defaults are generated from the md5sum of
"$mobility_domain/$auth_secret".  auth_secret is only set when using EAP
authentication, but the default key is used for SAE/PSK as well.  In
this case,  auth_secret is empty, and the default value of the key can
be computed from the SSID alone.

Fallback to using $key when auth_secret is empty.  While at it, rename
the variable holding the generated key from 'key' to 'ft_key', to avoid
clobbering the PSK.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
[make ft_key local]
Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agohostapd: add STA extended capabilities to get_clients
David Bauer [Wed, 16 Feb 2022 22:09:51 +0000 (23:09 +0100)]
hostapd: add STA extended capabilities to get_clients

Add the STAs extended capabilities to the ubus STA information. This
way, external daemons can be made aware of a STAs capabilities.

This field is of an array type and contains 0 or more bytes of a STAs
advertised extended capabilities.

Signed-off-by: David Bauer <mail@david-bauer.net>
2 years agonet: ethernet: mtk_eth_soc: add ipv6 flow offload support
David Bentham [Thu, 30 Dec 2021 19:55:48 +0000 (19:55 +0000)]
net: ethernet: mtk_eth_soc: add ipv6 flow offload support

Add the missing IPv6 flow offloading support for routing only.
Hardware flow offloading is done by the packet processing engine (PPE)
of the Ethernet MAC and as it doesn't support mangling of IPv6 packets,
IPv6 NAT cannot be supported.

Signed-off-by: David Bentham <db260179@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2 years agobuild: scripts/config - update to kconfig-v5.14
Eneas U de Queiroz [Wed, 24 Nov 2021 21:25:43 +0000 (18:25 -0300)]
build: scripts/config - update to kconfig-v5.14

Functional Changes
---------- -------
- make 'imply' not impose any restrictions: allow symbols implied by y
  to become m
- change "modules" from sub-option to first-level attribute

Bugfixes
--------
- nconf: fix core dump when searching in empty menu
- nconf: stop endless search loops
- xconfig: fix content of the main widget
- xconfig: fix support for the split view mode

Other Changes
----- -------
- highlight xconfig 'comment' lines with '***'
- xconfig: navigate menus on hyperlinks
- xconfig: drop support for Qt4
- improve host ncurses detection

Update the 'option modules' usage to just 'modules' in Config.in.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2 years agoath79: Add support for Ubiquiti NanoBeam AC Gen1 XC
Daniel González Cabanelas [Sun, 16 Jan 2022 18:00:19 +0000 (19:00 +0100)]
ath79: Add support for Ubiquiti NanoBeam AC Gen1 XC

The Ubiquiti NanoBeam AC Gen1 XC (NBE-5AC-19) is an outdoor 802.11ac CPE
with a waterproof casing (ultrasonically welded) and bulb shaped.

Hardware:
 - SoC: Qualcomm Atheros QCA9558
 - RAM: 128 MB DDR2
 - Flash: 16 MB SPI NOR
 - Ethernet: 1x GbE, AR8033 phy connected via SGMII
 - PSU: 24 Vdc passive PoE
 - WiFi 5 GHz: Qualcomm Atheros QCA988X
 - Buttons: 1x reset
 - LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue
 - Internal antenna: 19 dBi planar

Installation from stock airOS firmware:
 - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at
   https://openwrt.org/toh/ubiquiti/common

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2 years agobase-files: add support for heartbeat led trigger
Alexey Smirnov [Tue, 4 Jan 2022 07:11:51 +0000 (10:11 +0300)]
base-files: add support for heartbeat led trigger

This patch adds support for creation heartbeat led trigger with,
for example, this command:

ucidef_set_led_heartbeat "..." "..." "..."

from /etc/board.d/01_leds.

Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
2 years agox86: geode: add kmod-crypto-ebc needed for hw acceleration
Paul Fertser [Fri, 21 Jan 2022 17:12:29 +0000 (20:12 +0300)]
x86: geode: add kmod-crypto-ebc needed for hw acceleration

Module kmod-crypto-hw-geode provides accelerated cbc(aes) and ecb(aes)
but the software implementation is also needed when AES key size isn't
128 so that the operation can fall back. Add the kmod so that it would
all work as expected out of the box.

Tested-by: timur_davletshin
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2 years agogpio-nxp-74hc153: remove package
Mauri Sandberg [Sat, 5 Feb 2022 23:07:11 +0000 (01:07 +0200)]
gpio-nxp-74hc153: remove package

This module was used solely by Buffalo WZR-HP-G300NH devices
and has become obsolete with the introduction of gpio-cascade.

Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
2 years agoath79: use gpio-cascade for Buffalo WZR-HP-G300NH
Mauri Sandberg [Sat, 5 Feb 2022 23:07:10 +0000 (01:07 +0200)]
ath79: use gpio-cascade for Buffalo WZR-HP-G300NH

Switch to a generic GPIO cascade driver.

Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [missing commit description]
2 years agokernel: add package kmod-gpio-cascade
Mauri Sandberg [Sat, 5 Feb 2022 23:07:09 +0000 (01:07 +0200)]
kernel: add package kmod-gpio-cascade

Adds kernel module for Generic GPIO cascade.

Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [missing commit description]
2 years agokernel: add package kmod-multiplexer
Mauri Sandberg [Sat, 5 Feb 2022 23:07:08 +0000 (01:07 +0200)]
kernel: add package kmod-multiplexer

Adds new kernel module for GPIO controlled multiplexer support.

Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [missing commit description]
2 years agokernel: 5.10: backport gpio-cascade and related symbols
Mauri Sandberg [Sat, 5 Feb 2022 23:07:07 +0000 (01:07 +0200)]
kernel: 5.10: backport gpio-cascade and related symbols

The patch is under review at [1].

Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
[1] http://patchwork.ozlabs.org/project/linux-gpio/patch/20211026191506.3099-3-maukka@ext.kapsi.fi/

2 years agoconfig: build: cleanup whitespace issue
Petr Štetiar [Thu, 3 Feb 2022 11:13:00 +0000 (12:13 +0100)]
config: build: cleanup whitespace issue

In order to have it tidy.

Signed-off-by: Petr Štetiar <ynezz@true.cz>
2 years agoprocd: update to git HEAD
Daniel Golle [Sat, 19 Feb 2022 00:10:18 +0000 (00:10 +0000)]
procd: update to git HEAD

 a87d010 uxc: remove unused printf parameter
 ad65249 instance: exit in case asprintf() fails

Build with glibc should again work after this commit.

Fixes: e9e61d76fd ("procd: update to git HEAD")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agorealtek: fix locking bug in rtl838x_hw_receive()
Birger Koblitz [Fri, 18 Feb 2022 11:01:53 +0000 (12:01 +0100)]
realtek: fix locking bug in rtl838x_hw_receive()

A Locking bug in the packet receive path was introduced with PR
#4973. The following patch prevents the driver from locking
after a few minutes with an endless flow of

[ 1434.185085] rtl838x-eth 1b00a300.ethernet eth0: Ring contention: r: 0, last a28000f4, cur a28000f8
[ 1434.208971] rtl838x-eth 1b00a300.ethernet eth0: Ring contention: r: 0, last a28000f4, cur a28000fc
[ 1434.794800] rtl838x-eth 1b00a300.ethernet eth0: Ring contention: r: 0, last a28000f4, cur a28000fc
[ 1435.049187] rtl838x-eth 1b00a300.ethernet eth0: Ring contention: r: 0, last a28000f4, cur a28000fc

Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Birger Koblitz <mail@birger-koblitz.de>
2 years agoprocd: update to git HEAD
Daniel Golle [Fri, 18 Feb 2022 02:57:52 +0000 (02:57 +0000)]
procd: update to git HEAD

 df1123e uxc: add support for user-defined settings
 0272c7c uxc: allow editing settings using 'create'
 a839518 uxc: clean up error handling

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2 years agosunix: fix typo in kmod-ata-core
Paul Spooren [Thu, 17 Feb 2022 23:50:24 +0000 (00:50 +0100)]
sunix: fix typo in kmod-ata-core

There was a missing `k` in the package name.
s/mod-ata-core/kmod-ata-core

Signed-off-by: Paul Spooren <mail@aparcar.org>
2 years agorealtek: add RTL8231 chip detection
Sander Vanheule [Sat, 20 Nov 2021 19:11:34 +0000 (20:11 +0100)]
realtek: add RTL8231 chip detection

When initialising the driver, check if the RTL8231 chip is actually
present at the specified address. If the READY_CODE value does not match
the expected value, return -ENXIO to fail probing.

This should help users to figure out which address an RTL8231 is
configured to use, if measuring pull-up/-down resistors is not an
option.

On an unsuccesful probe, the driver will log:
    [    0.795364] Probing RTL8231 GPIOs
    [    0.798978] rtl8231_init called, MDIO bus ID: 30
    [    0.804194] rtl8231-gpio rtl8231-gpio: no device found at bus address 30

When a device is found, only the first two lines will be logged:
    [    0.453698] Probing RTL8231 GPIOs
    [    0.457312] rtl8231_init called, MDIO bus ID: 31

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
2 years agorealtek: always require SMI bus ID for RTL8231
Sander Vanheule [Sat, 20 Nov 2021 19:11:33 +0000 (20:11 +0100)]
realtek: always require SMI bus ID for RTL8231

The SMI bus ID for RTL8231 currently defaults to 0, and can be
overridden from the devicetree. However, there is no value check on the
DT-provided value, aside from masking which would only cause value
wrap-around.

Change the driver to always require the "indirect-access-bus-id"
property, as there is no real reason to use 0 as default, and perform a
sanity check on the value when probing. This allows the other parts of
the driver to be simplified a bit.

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>