--- a/nl80211.h
+++ b/nl80211.h
-@@ -249,6 +249,22 @@
+@@ -11,7 +11,7 @@
+ * Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
+ * Copyright 2008 Colin McCabe <colin@cozybit.com>
+ * Copyright 2015-2017 Intel Deutschland GmbH
+- * Copyright (C) 2018-2019 Intel Corporation
++ * Copyright (C) 2018-2020 Intel Corporation
+ *
+ * Permission to use, copy, modify, and/or distribute this software for any
+ * purpose with or without fee is hereby granted, provided that the above
+@@ -249,6 +249,45 @@
*/
/**
+ * %NL80211_ATTR_VLAN_ID.
+ */
+
++/**
++ * DOC: TID configuration
++ *
++ * TID config support can be checked in the %NL80211_ATTR_TID_CONFIG
++ * attribute given in wiphy capabilities.
++ *
++ * The necessary configuration parameters are mentioned in
++ * &enum nl80211_tid_config_attr and it will be passed to the
++ * %NL80211_CMD_SET_TID_CONFIG command in %NL80211_ATTR_TID_CONFIG.
++ *
++ * If the configuration needs to be applied for specific peer then the MAC
++ * address of the peer needs to be passed in %NL80211_ATTR_MAC, otherwise the
++ * configuration will be applied for all the connected peers in the vif except
++ * any peers that have peer specific configuration for the TID by default; if
++ * the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer specific values
++ * will be overwritten.
++ *
++ * All this configuration is valid only for STA's current connection
++ * i.e. the configuration will be reset to default when the STA connects back
++ * after disconnection/roaming, and this configuration will be cleared when
++ * the interface goes down.
++ */
++
+/**
* enum nl80211_commands - supported nl80211 commands
*
* @NL80211_CMD_UNSPEC: unspecified command to catch errors
-@@ -571,6 +587,14 @@
+@@ -571,6 +610,14 @@
* set of BSSID,frequency parameters is used (i.e., either the enforcing
* %NL80211_ATTR_MAC,%NL80211_ATTR_WIPHY_FREQ or the less strict
* %NL80211_ATTR_MAC_HINT and %NL80211_ATTR_WIPHY_FREQ_HINT).
* %NL80211_ATTR_PREV_BSSID can be used to request a reassociation within
* the ESS in case the device is already associated and an association with
* a different BSS is desired.
-@@ -2373,6 +2397,12 @@ enum nl80211_commands {
+@@ -1101,6 +1148,9 @@
+ * peer MAC address and %NL80211_ATTR_FRAME is used to specify the frame
+ * content. The frame is ethernet data.
+ *
++ * @NL80211_CMD_SET_TID_CONFIG: Data frame TID specific configuration
++ * is passed using %NL80211_ATTR_TID_CONFIG attribute.
++ *
+ * @NL80211_CMD_MAX: highest used command number
+ * @__NL80211_CMD_AFTER_LAST: internal use
+ */
+@@ -1325,6 +1375,8 @@ enum nl80211_commands {
+
+ NL80211_CMD_PROBE_MESH_LINK,
+
++ NL80211_CMD_SET_TID_CONFIG,
++
+ /* add new commands above here */
+
+ /* used to define NL80211_CMD_MAX below */
+@@ -1580,7 +1632,8 @@ enum nl80211_commands {
+ * flag is included, then control port frames are sent over NL80211 instead
+ * using %CMD_CONTROL_PORT_FRAME. If control port routing over NL80211 is
+ * to be used then userspace must also use the %NL80211_ATTR_SOCKET_OWNER
+- * flag.
++ * flag. When used with %NL80211_ATTR_CONTROL_PORT_NO_PREAUTH, pre-auth
++ * frames are not forwared over the control port.
+ *
+ * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
+ * We recommend using nested, driver-specific attributes within this.
+@@ -2373,6 +2426,53 @@ enum nl80211_commands {
* the allowed channel bandwidth configurations. (u8 attribute)
* Defined by IEEE P802.11ay/D4.0 section 9.4.2.251, Table 13.
*
+ * @NL80211_ATTR_VLAN_ID: VLAN ID (1..4094) for the station and VLAN group key
+ * (u16).
+ *
++ * @NL80211_ATTR_HE_BSS_COLOR: nested attribute for BSS Color Settings.
++ *
++ * @NL80211_ATTR_IFTYPE_AKM_SUITES: nested array attribute, with each entry
++ * using attributes from &enum nl80211_iftype_akm_attributes. This
++ * attribute is sent in a response to %NL80211_CMD_GET_WIPHY indicating
++ * supported AKM suites capability per interface. AKMs advertised in
++ * %NL80211_ATTR_AKM_SUITES are default capabilities if AKM suites not
++ * advertised for a specific interface type.
++ *
++ * @NL80211_ATTR_TID_CONFIG: TID specific configuration in a
++ * nested attribute with &enum nl80211_tid_config_attr sub-attributes;
++ * on output (in wiphy attributes) it contains only the feature sub-
++ * attributes.
++ *
++ * @NL80211_ATTR_CONTROL_PORT_NO_PREAUTH: disable preauth frame rx on control
++ * port in order to forward/receive them as ordinary data frames.
++ *
++ * @NL80211_ATTR_PMK_LIFETIME: Maximum lifetime for PMKSA in seconds (u32,
++ * dot11RSNAConfigPMKReauthThreshold; 0 is not a valid value).
++ * An optional parameter configured through %NL80211_CMD_SET_PMKSA.
++ * Drivers that trigger roaming need to know the lifetime of the
++ * configured PMKSA for triggering the full vs. PMKSA caching based
++ * authentication. This timeout helps authentication methods like SAE,
++ * where PMK gets updated only by going through a full (new SAE)
++ * authentication instead of getting updated during an association for EAP
++ * authentication. No new full authentication within the PMK expiry shall
++ * result in a disassociation at the end of the lifetime.
++ *
++ * @NL80211_ATTR_PMK_REAUTH_THRESHOLD: Reauthentication threshold time, in
++ * terms of percentage of %NL80211_ATTR_PMK_LIFETIME
++ * (u8, dot11RSNAConfigPMKReauthThreshold, 1..100). This is an optional
++ * parameter configured through %NL80211_CMD_SET_PMKSA. Requests the
++ * driver to trigger a full authentication roam (without PMKSA caching)
++ * after the reauthentication threshold time, but before the PMK lifetime
++ * has expired.
++ *
++ * Authentication methods like SAE need to be able to generate a new PMKSA
++ * entry without having to force a disconnection after the PMK timeout. If
++ * no roaming occurs between the reauth threshold and PMK expiration,
++ * disassociation is still forced.
++ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_GAIN: Configured antenna gain. Used to reduce
+ * transmit power to stay within regulatory limits. u32, dBi.
+ *
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
-@@ -2835,6 +2865,10 @@ enum nl80211_attrs {
+@@ -2835,6 +2935,21 @@ enum nl80211_attrs {
NL80211_ATTR_WIPHY_EDMG_CHANNELS,
NL80211_ATTR_WIPHY_EDMG_BW_CONFIG,
+ NL80211_ATTR_VLAN_ID,
+
++ NL80211_ATTR_HE_BSS_COLOR,
++
++ NL80211_ATTR_IFTYPE_AKM_SUITES,
++
++ NL80211_ATTR_TID_CONFIG,
++
++ NL80211_ATTR_CONTROL_PORT_NO_PREAUTH,
++
++ NL80211_ATTR_PMK_LIFETIME,
++ NL80211_ATTR_PMK_REAUTH_THRESHOLD,
++
+ NL80211_ATTR_WIPHY_ANTENNA_GAIN,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
-@@ -5484,6 +5518,14 @@ enum nl80211_feature_flags {
+@@ -3554,6 +3669,8 @@ enum nl80211_wmm_rule {
+ * @NL80211_FREQUENCY_ATTR_WMM: this channel has wmm limitations.
+ * This is a nested attribute that contains the wmm limitation per AC.
+ * (see &enum nl80211_wmm_rule)
++ * @NL80211_FREQUENCY_ATTR_NO_HE: HE operation is not allowed on this channel
++ * in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
+ * currently defined
+ * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
+@@ -3583,6 +3700,7 @@ enum nl80211_frequency_attr {
+ NL80211_FREQUENCY_ATTR_NO_20MHZ,
+ NL80211_FREQUENCY_ATTR_NO_10MHZ,
+ NL80211_FREQUENCY_ATTR_WMM,
++ NL80211_FREQUENCY_ATTR_NO_HE,
+
+ /* keep last */
+ __NL80211_FREQUENCY_ATTR_AFTER_LAST,
+@@ -3780,6 +3898,7 @@ enum nl80211_sched_scan_match_attr {
+ * @NL80211_RRF_NO_HT40PLUS: channels can't be used in HT40+ operation
+ * @NL80211_RRF_NO_80MHZ: 80MHz operation not allowed
+ * @NL80211_RRF_NO_160MHZ: 160MHz operation not allowed
++ * @NL80211_RRF_NO_HE: HE operation not allowed
+ */
+ enum nl80211_reg_rule_flags {
+ NL80211_RRF_NO_OFDM = 1<<0,
+@@ -3797,6 +3916,7 @@ enum nl80211_reg_rule_flags {
+ NL80211_RRF_NO_HT40PLUS = 1<<14,
+ NL80211_RRF_NO_80MHZ = 1<<15,
+ NL80211_RRF_NO_160MHZ = 1<<16,
++ NL80211_RRF_NO_HE = 1<<17,
+ };
+
+ #define NL80211_RRF_PASSIVE_SCAN NL80211_RRF_NO_IR
+@@ -4503,6 +4623,7 @@ enum nl80211_key_default_types {
+ * See &enum nl80211_key_default_types.
+ * @NL80211_KEY_MODE: the mode from enum nl80211_key_mode.
+ * Defaults to @NL80211_KEY_RX_TX.
++ * @NL80211_KEY_DEFAULT_BEACON: flag indicating default Beacon frame key
+ *
+ * @__NL80211_KEY_AFTER_LAST: internal
+ * @NL80211_KEY_MAX: highest key attribute
+@@ -4518,6 +4639,7 @@ enum nl80211_key_attributes {
+ NL80211_KEY_TYPE,
+ NL80211_KEY_DEFAULT_TYPES,
+ NL80211_KEY_MODE,
++ NL80211_KEY_DEFAULT_BEACON,
+
+ /* keep last */
+ __NL80211_KEY_AFTER_LAST,
+@@ -4674,6 +4796,69 @@ enum nl80211_tx_power_setting {
+ };
+
+ /**
++ * enum nl80211_tid_config - TID config state
++ * @NL80211_TID_CONFIG_ENABLE: Enable config for the TID
++ * @NL80211_TID_CONFIG_DISABLE: Disable config for the TID
++ */
++enum nl80211_tid_config {
++ NL80211_TID_CONFIG_ENABLE,
++ NL80211_TID_CONFIG_DISABLE,
++};
++
++/* enum nl80211_tid_config_attr - TID specific configuration.
++ * @NL80211_TID_CONFIG_ATTR_PAD: pad attribute for 64-bit values
++ * @NL80211_TID_CONFIG_ATTR_VIF_SUPP: a bitmap (u64) of attributes supported
++ * for per-vif configuration; doesn't list the ones that are generic
++ * (%NL80211_TID_CONFIG_ATTR_TIDS, %NL80211_TID_CONFIG_ATTR_OVERRIDE).
++ * @NL80211_TID_CONFIG_ATTR_PEER_SUPP: same as the previous per-vif one, but
++ * per peer instead.
++ * @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribue, if no peer
++ * is selected, if set indicates that the new configuration overrides
++ * all previous peer configurations, otherwise previous peer specific
++ * configurations should be left untouched. If peer is selected then
++ * it will reset particular TID configuration of that peer and it will
++ * not accept other TID config attributes along with peer.
++ * @NL80211_TID_CONFIG_ATTR_TIDS: a bitmask value of TIDs (bit 0 to 7)
++ * Its type is u16.
++ * @NL80211_TID_CONFIG_ATTR_NOACK: Configure ack policy for the TID.
++ * specified in %NL80211_TID_CONFIG_ATTR_TID. see %enum nl80211_tid_config.
++ * Its type is u8.
++ * @NL80211_TID_CONFIG_ATTR_RETRY_SHORT: Number of retries used with data frame
++ * transmission, user-space sets this configuration in
++ * &NL80211_CMD_SET_TID_CONFIG. It is u8 type, min value is 1 and
++ * the max value is advertised by the driver in this attribute on
++ * output in wiphy capabilities.
++ * @NL80211_TID_CONFIG_ATTR_RETRY_LONG: Number of retries used with data frame
++ * transmission, user-space sets this configuration in
++ * &NL80211_CMD_SET_TID_CONFIG. Its type is u8, min value is 1 and
++ * the max value is advertised by the driver in this attribute on
++ * output in wiphy capabilities.
++ * @NL80211_TID_CONFIG_ATTR_AMPDU_CTRL: Enable/Disable aggregation for the TIDs
++ * specified in %NL80211_TID_CONFIG_ATTR_TIDS. Its type is u8, using
++ * the values from &nl80211_tid_config.
++ * @NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL: Enable/Disable RTS_CTS for the TIDs
++ * specified in %NL80211_TID_CONFIG_ATTR_TIDS. It is u8 type, using
++ * the values from &nl80211_tid_config.
++ */
++enum nl80211_tid_config_attr {
++ __NL80211_TID_CONFIG_ATTR_INVALID,
++ NL80211_TID_CONFIG_ATTR_PAD,
++ NL80211_TID_CONFIG_ATTR_VIF_SUPP,
++ NL80211_TID_CONFIG_ATTR_PEER_SUPP,
++ NL80211_TID_CONFIG_ATTR_OVERRIDE,
++ NL80211_TID_CONFIG_ATTR_TIDS,
++ NL80211_TID_CONFIG_ATTR_NOACK,
++ NL80211_TID_CONFIG_ATTR_RETRY_SHORT,
++ NL80211_TID_CONFIG_ATTR_RETRY_LONG,
++ NL80211_TID_CONFIG_ATTR_AMPDU_CTRL,
++ NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL,
++
++ /* keep last */
++ __NL80211_TID_CONFIG_ATTR_AFTER_LAST,
++ NL80211_TID_CONFIG_ATTR_MAX = __NL80211_TID_CONFIG_ATTR_AFTER_LAST - 1
++};
++
++/**
+ * enum nl80211_packet_pattern_attr - packet pattern attribute
+ * @__NL80211_PKTPAT_INVALID: invalid number for nested attribute
+ * @NL80211_PKTPAT_PATTERN: the pattern, values where the mask has
+@@ -5484,6 +5669,26 @@ enum nl80211_feature_flags {
* @NL80211_EXT_FEATURE_SAE_OFFLOAD: Device wants to do SAE authentication in
* station mode (SAE password is passed as part of the connect command).
*
+ * @NL80211_EXT_FEATURE_AQL: The driver supports the Airtime Queue Limit (AQL)
+ * feature, which prevents bufferbloat by using the expected transmission
+ * time to limit the amount of data buffered in the hardware.
++ *
++ * @NL80211_EXT_FEATURE_BEACON_PROTECTION: The driver supports Beacon protection
++ * and can receive key configuration for BIGTK using key indexes 6 and 7.
++ *
++ * @NL80211_EXT_FEATURE_CONTROL_PORT_NO_PREAUTH: The driver can disable the
++ * forwarding of preauth frames over the control port. They are then
++ * handled as ordinary data frames.
++ *
++ * @NL80211_EXT_FEATURE_PROTECTED_TWT: Driver supports protected TWT frames
++ *
++ * @NL80211_EXT_FEATURE_DEL_IBSS_STA: The driver supports removing stations
++ * in IBSS mode, essentially by dropping their state.
+ *
* @NUM_NL80211_EXT_FEATURES: number of extended features.
* @MAX_NL80211_EXT_FEATURES: highest extended feature index.
*/
-@@ -5529,6 +5571,8 @@ enum nl80211_ext_feature_index {
+@@ -5529,6 +5734,12 @@ enum nl80211_ext_feature_index {
NL80211_EXT_FEATURE_EXT_KEY_ID,
NL80211_EXT_FEATURE_STA_TX_PWR,
NL80211_EXT_FEATURE_SAE_OFFLOAD,
+ NL80211_EXT_FEATURE_VLAN_OFFLOAD,
+ NL80211_EXT_FEATURE_AQL,
++ NL80211_EXT_FEATURE_BEACON_PROTECTION,
++ NL80211_EXT_FEATURE_CONTROL_PORT_NO_PREAUTH,
++ NL80211_EXT_FEATURE_PROTECTED_TWT,
++ NL80211_EXT_FEATURE_DEL_IBSS_STA,
/* add new features before the definition below */
NUM_NL80211_EXT_FEATURES,
+@@ -6151,12 +6362,14 @@ enum nl80211_ftm_responder_stats {
+ * @NL80211_PREAMBLE_HT: HT preamble
+ * @NL80211_PREAMBLE_VHT: VHT preamble
+ * @NL80211_PREAMBLE_DMG: DMG preamble
++ * @NL80211_PREAMBLE_HE: HE preamble
+ */
+ enum nl80211_preamble {
+ NL80211_PREAMBLE_LEGACY,
+ NL80211_PREAMBLE_HT,
+ NL80211_PREAMBLE_VHT,
+ NL80211_PREAMBLE_DMG,
++ NL80211_PREAMBLE_HE,
+ };
+
+ /**
+@@ -6349,6 +6562,10 @@ enum nl80211_peer_measurement_attrs {
+ * is valid)
+ * @NL80211_PMSR_FTM_CAPA_ATTR_MAX_FTMS_PER_BURST: u32 attribute indicating
+ * the maximum FTMs per burst (if not present anything is valid)
++ * @NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED: flag attribute indicating if
++ * trigger based ranging measurement is supported
++ * @NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED: flag attribute indicating
++ * if non trigger based ranging measurement is supported
+ *
+ * @NUM_NL80211_PMSR_FTM_CAPA_ATTR: internal
+ * @NL80211_PMSR_FTM_CAPA_ATTR_MAX: highest attribute number
+@@ -6364,6 +6581,8 @@ enum nl80211_peer_measurement_ftm_capa {
+ NL80211_PMSR_FTM_CAPA_ATTR_BANDWIDTHS,
+ NL80211_PMSR_FTM_CAPA_ATTR_MAX_BURSTS_EXPONENT,
+ NL80211_PMSR_FTM_CAPA_ATTR_MAX_FTMS_PER_BURST,
++ NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED,
++ NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED,
+
+ /* keep last */
+ NUM_NL80211_PMSR_FTM_CAPA_ATTR,
+@@ -6393,6 +6612,20 @@ enum nl80211_peer_measurement_ftm_capa {
+ * @NL80211_PMSR_FTM_REQ_ATTR_REQUEST_LCI: request LCI data (flag)
+ * @NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC: request civic location data
+ * (flag)
++ * @NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED: request trigger based ranging
++ * measurement (flag).
++ * This attribute and %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED are
++ * mutually exclusive.
++ * if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
++ * %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
++ * ranging will be used.
++ * @NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED: request non trigger based
++ * ranging measurement (flag)
++ * This attribute and %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED are
++ * mutually exclusive.
++ * if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
++ * %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
++ * ranging will be used.
+ *
+ * @NUM_NL80211_PMSR_FTM_REQ_ATTR: internal
+ * @NL80211_PMSR_FTM_REQ_ATTR_MAX: highest attribute number
+@@ -6409,6 +6642,8 @@ enum nl80211_peer_measurement_ftm_req {
+ NL80211_PMSR_FTM_REQ_ATTR_NUM_FTMR_RETRIES,
+ NL80211_PMSR_FTM_REQ_ATTR_REQUEST_LCI,
+ NL80211_PMSR_FTM_REQ_ATTR_REQUEST_CIVICLOC,
++ NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED,
++ NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED,
+
+ /* keep last */
+ NUM_NL80211_PMSR_FTM_REQ_ATTR,
+@@ -6548,5 +6783,51 @@ enum nl80211_obss_pd_attributes {
+ NL80211_HE_OBSS_PD_ATTR_MAX = __NL80211_HE_OBSS_PD_ATTR_LAST - 1,
+ };
+
++/**
++ * enum nl80211_bss_color_attributes - BSS Color attributes
++ * @__NL80211_HE_BSS_COLOR_ATTR_INVALID: Invalid
++ *
++ * @NL80211_HE_BSS_COLOR_ATTR_COLOR: the current BSS Color.
++ * @NL80211_HE_BSS_COLOR_ATTR_DISABLED: is BSS coloring disabled.
++ * @NL80211_HE_BSS_COLOR_ATTR_PARTIAL: the AID equation to be used..
++ *
++ * @__NL80211_HE_BSS_COLOR_ATTR_LAST: Internal
++ * @NL80211_HE_BSS_COLOR_ATTR_MAX: highest BSS Color attribute.
++ */
++enum nl80211_bss_color_attributes {
++ __NL80211_HE_BSS_COLOR_ATTR_INVALID,
++
++ NL80211_HE_BSS_COLOR_ATTR_COLOR,
++ NL80211_HE_BSS_COLOR_ATTR_DISABLED,
++ NL80211_HE_BSS_COLOR_ATTR_PARTIAL,
++
++ /* keep last */
++ __NL80211_HE_BSS_COLOR_ATTR_LAST,
++ NL80211_HE_BSS_COLOR_ATTR_MAX = __NL80211_HE_BSS_COLOR_ATTR_LAST - 1,
++};
++
++/**
++ * enum nl80211_iftype_akm_attributes - interface type AKM attributes
++ * @__NL80211_IFTYPE_AKM_ATTR_INVALID: Invalid
++ *
++ * @NL80211_IFTYPE_AKM_ATTR_IFTYPES: nested attribute containing a flag
++ * attribute for each interface type that supports AKM suites specified in
++ * %NL80211_IFTYPE_AKM_ATTR_SUITES
++ * @NL80211_IFTYPE_AKM_ATTR_SUITES: an array of u32. Used to indicate supported
++ * AKM suites for the specified interface types.
++ *
++ * @__NL80211_IFTYPE_AKM_ATTR_LAST: Internal
++ * @NL80211_IFTYPE_AKM_ATTR_MAX: highest interface type AKM attribute.
++ */
++enum nl80211_iftype_akm_attributes {
++ __NL80211_IFTYPE_AKM_ATTR_INVALID,
++
++ NL80211_IFTYPE_AKM_ATTR_IFTYPES,
++ NL80211_IFTYPE_AKM_ATTR_SUITES,
++
++ /* keep last */
++ __NL80211_IFTYPE_AKM_ATTR_LAST,
++ NL80211_IFTYPE_AKM_ATTR_MAX = __NL80211_IFTYPE_AKM_ATTR_LAST - 1,
++};
+
+ #endif /* __LINUX_NL80211_H */
projects / openwrt / openwrt.git / blobdiff