--- a/nl80211.h
+++ b/nl80211.h
-@@ -252,9 +252,13 @@
- * DOC: SAE authentication offload
+@@ -2527,6 +2527,9 @@ enum nl80211_commands {
+ * override mask. Used with NL80211_ATTR_S1G_CAPABILITY in
+ * NL80211_CMD_ASSOCIATE or NL80211_CMD_CONNECT.
*
- * By setting @NL80211_EXT_FEATURE_SAE_OFFLOAD flag drivers can indicate they
-- * support offloading SAE authentication for WPA3-Personal networks. In
-- * %NL80211_CMD_CONNECT the password for SAE should be specified using
-- * %NL80211_ATTR_SAE_PASSWORD.
-+ * support offloading SAE authentication for WPA3-Personal networks in station
-+ * mode. Similarly @NL80211_EXT_FEATURE_SAE_OFFLOAD_AP flag can be set by
-+ * drivers indicating the offload support in AP mode.
-+ *
-+ * The password for SAE should be specified using %NL80211_ATTR_SAE_PASSWORD in
-+ * %NL80211_CMD_CONNECT and %NL80211_CMD_START_AP for station and AP mode
-+ * respectively.
- */
-
- /**
-@@ -647,13 +651,9 @@
- * authentication/association or not receiving a response from the AP.
- * Non-zero %NL80211_ATTR_STATUS_CODE value is indicated in that case as
- * well to remain backwards compatible.
-- * When establishing a security association, drivers that support 4 way
-- * handshake offload should send %NL80211_CMD_PORT_AUTHORIZED event when
-- * the 4 way handshake is completed successfully.
- * @NL80211_CMD_ROAM: Notification indicating the card/driver roamed by itself.
-- * When a security association was established with the new AP (e.g. if
-- * the FT protocol was used for roaming or the driver completed the 4 way
-- * handshake), this event should be followed by an
-+ * When a security association was established on an 802.1X network using
-+ * fast transition, this event should be followed by an
- * %NL80211_CMD_PORT_AUTHORIZED event.
- * @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify
- * userspace that a connection was dropped by the AP or due to other
-@@ -1067,13 +1067,11 @@
- * @NL80211_CMD_DEL_PMK: For offloaded 4-Way handshake, delete the previously
- * configured PMK for the authenticator address identified by
- * %NL80211_ATTR_MAC.
-- * @NL80211_CMD_PORT_AUTHORIZED: An event that indicates that the 4 way
-- * handshake was completed successfully by the driver. The BSSID is
-- * specified with %NL80211_ATTR_MAC. Drivers that support 4 way handshake
-- * offload should send this event after indicating 802.11 association with
-- * %NL80211_CMD_CONNECT or %NL80211_CMD_ROAM. If the 4 way handshake failed
-- * %NL80211_CMD_DISCONNECT should be indicated instead.
-- *
-+ * @NL80211_CMD_PORT_AUTHORIZED: An event that indicates an 802.1X FT roam was
-+ * completed successfully. Drivers that support 4 way handshake offload
-+ * should send this event after indicating 802.1X FT assocation with
-+ * %NL80211_CMD_ROAM. If the 4 way handshake failed %NL80211_CMD_DISCONNECT
-+ * should be indicated instead.
- * @NL80211_CMD_CONTROL_PORT_FRAME: Control Port (e.g. PAE) frame TX request
- * and RX notification. This command is used both as a request to transmit
- * a control port frame and as a notification that a control port frame
-@@ -2082,10 +2080,10 @@ enum nl80211_commands {
- * operation).
- * @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information
- * for the time while performing a channel switch.
-- * @NL80211_ATTR_CSA_C_OFF_BEACON: An array of offsets (u16) to the channel
-- * switch counters in the beacons tail (%NL80211_ATTR_BEACON_TAIL).
-- * @NL80211_ATTR_CSA_C_OFF_PRESP: An array of offsets (u16) to the channel
-- * switch counters in the probe response (%NL80211_ATTR_PROBE_RESP).
-+ * @NL80211_ATTR_CNTDWN_OFFS_BEACON: An array of offsets (u16) to the channel
-+ * switch or color change counters in the beacons tail (%NL80211_ATTR_BEACON_TAIL).
-+ * @NL80211_ATTR_CNTDWN_OFFS_PRESP: An array of offsets (u16) to the channel
-+ * switch or color change counters in the probe response (%NL80211_ATTR_PROBE_RESP).
- *
- * @NL80211_ATTR_RXMGMT_FLAGS: flags for nl80211_send_mgmt(), u32.
- * As specified in the &enum nl80211_rxmgmt_flags.
-@@ -2515,6 +2513,23 @@ enum nl80211_commands {
- * @NL80211_ATTR_HE_6GHZ_CAPABILITY: HE 6 GHz Band Capability element (from
- * association request when used with NL80211_CMD_NEW_STATION).
- *
-+ * @NL80211_ATTR_FILS_DISCOVERY: Optional parameter to configure FILS
-+ * discovery. It is a nested attribute, see
-+ * &enum nl80211_fils_discovery_attributes.
-+ *
-+ * @NL80211_ATTR_UNSOL_BCAST_PROBE_RESP: Optional parameter to configure
-+ * unsolicited broadcast probe response. It is a nested attribute, see
-+ * &enum nl80211_unsol_bcast_probe_resp_attributes.
-+ *
-+ * @NL80211_ATTR_S1G_CAPABILITY: S1G Capability information element (from
-+ * association request when used with NL80211_CMD_NEW_STATION)
-+ * @NL80211_ATTR_S1G_CAPABILITY_MASK: S1G Capability Information element
-+ * override mask. Used with NL80211_ATTR_S1G_CAPABILITY in
-+ * NL80211_CMD_ASSOCIATE or NL80211_CMD_CONNECT.
-+ *
+ * @NL80211_ATTR_WIPHY_ANTENNA_GAIN: Configured antenna gain. Used to reduce
+ * transmit power to stay within regulatory limits. u32, dBi.
+ *
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
-@@ -2821,8 +2836,8 @@ enum nl80211_attrs {
- NL80211_ATTR_CH_SWITCH_COUNT,
- NL80211_ATTR_CH_SWITCH_BLOCK_TX,
- NL80211_ATTR_CSA_IES,
-- NL80211_ATTR_CSA_C_OFF_BEACON,
-- NL80211_ATTR_CSA_C_OFF_PRESP,
-+ NL80211_ATTR_CNTDWN_OFFS_BEACON,
-+ NL80211_ATTR_CNTDWN_OFFS_PRESP,
-
- NL80211_ATTR_RXMGMT_FLAGS,
-
-@@ -2997,6 +3012,15 @@ enum nl80211_attrs {
+@@ -3016,6 +3019,8 @@ enum nl80211_attrs {
+ NL80211_ATTR_S1G_CAPABILITY,
+ NL80211_ATTR_S1G_CAPABILITY_MASK,
- NL80211_ATTR_HE_6GHZ_CAPABILITY,
-
-+ NL80211_ATTR_FILS_DISCOVERY,
-+
-+ NL80211_ATTR_UNSOL_BCAST_PROBE_RESP,
-+
-+ NL80211_ATTR_S1G_CAPABILITY,
-+ NL80211_ATTR_S1G_CAPABILITY_MASK,
-+
+ NL80211_ATTR_WIPHY_ANTENNA_GAIN,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
-@@ -3009,6 +3033,8 @@ enum nl80211_attrs {
- #define NL80211_ATTR_MESH_PARAMS NL80211_ATTR_MESH_CONFIG
- #define NL80211_ATTR_IFACE_SOCKET_OWNER NL80211_ATTR_SOCKET_OWNER
- #define NL80211_ATTR_SAE_DATA NL80211_ATTR_AUTH_DATA
-+#define NL80211_ATTR_CSA_C_OFF_BEACON NL80211_ATTR_CNTDWN_OFFS_BEACON
-+#define NL80211_ATTR_CSA_C_OFF_PRESP NL80211_ATTR_CNTDWN_OFFS_PRESP
-
- /*
- * Allow user space programs to use #ifdef on new attributes by defining them
-@@ -3186,6 +3212,18 @@ enum nl80211_he_gi {
- NL80211_RATE_INFO_HE_GI_3_2,
- };
-
-+/**
-+ * enum nl80211_he_ltf - HE long training field
-+ * @NL80211_RATE_INFO_HE_1xLTF: 3.2 usec
-+ * @NL80211_RATE_INFO_HE_2xLTF: 6.4 usec
-+ * @NL80211_RATE_INFO_HE_4xLTF: 12.8 usec
-+ */
-+enum nl80211_he_ltf {
-+ NL80211_RATE_INFO_HE_1XLTF,
-+ NL80211_RATE_INFO_HE_2XLTF,
-+ NL80211_RATE_INFO_HE_4XLTF,
-+};
-+
- /**
- * enum nl80211_he_ru_alloc - HE RU allocation values
- * @NL80211_RATE_INFO_HE_RU_ALLOC_26: 26-tone RU allocation
-@@ -3725,6 +3763,16 @@ enum nl80211_wmm_rule {
- * @NL80211_FREQUENCY_ATTR_NO_HE: HE operation is not allowed on this channel
- * in current regulatory domain.
- * @NL80211_FREQUENCY_ATTR_OFFSET: frequency offset in KHz
-+ * @NL80211_FREQUENCY_ATTR_1MHZ: 1 MHz operation is allowed
-+ * on this channel in current regulatory domain.
-+ * @NL80211_FREQUENCY_ATTR_2MHZ: 2 MHz operation is allowed
-+ * on this channel in current regulatory domain.
-+ * @NL80211_FREQUENCY_ATTR_4MHZ: 4 MHz operation is allowed
-+ * on this channel in current regulatory domain.
-+ * @NL80211_FREQUENCY_ATTR_8MHZ: 8 MHz operation is allowed
-+ * on this channel in current regulatory domain.
-+ * @NL80211_FREQUENCY_ATTR_16MHZ: 16 MHz operation is allowed
-+ * on this channel in current regulatory domain.
- * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
- * currently defined
- * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
-@@ -3756,6 +3804,11 @@ enum nl80211_frequency_attr {
- NL80211_FREQUENCY_ATTR_WMM,
- NL80211_FREQUENCY_ATTR_NO_HE,
- NL80211_FREQUENCY_ATTR_OFFSET,
-+ NL80211_FREQUENCY_ATTR_1MHZ,
-+ NL80211_FREQUENCY_ATTR_2MHZ,
-+ NL80211_FREQUENCY_ATTR_4MHZ,
-+ NL80211_FREQUENCY_ATTR_8MHZ,
-+ NL80211_FREQUENCY_ATTR_16MHZ,
-
- /* keep last */
- __NL80211_FREQUENCY_ATTR_AFTER_LAST,
-@@ -4049,6 +4102,7 @@ enum nl80211_user_reg_hint_type {
- * receiving frames destined to the local BSS
- * @NL80211_SURVEY_INFO_MAX: highest survey info attribute number
- * currently defined
-+ * @NL80211_SURVEY_INFO_FREQUENCY_OFFSET: center frequency offset in KHz
- * @__NL80211_SURVEY_INFO_AFTER_LAST: internal use
- */
- enum nl80211_survey_info {
-@@ -4064,6 +4118,7 @@ enum nl80211_survey_info {
- NL80211_SURVEY_INFO_TIME_SCAN,
- NL80211_SURVEY_INFO_PAD,
- NL80211_SURVEY_INFO_TIME_BSS_RX,
-+ NL80211_SURVEY_INFO_FREQUENCY_OFFSET,
-
- /* keep last */
- __NL80211_SURVEY_INFO_AFTER_LAST,
-@@ -4741,6 +4796,10 @@ enum nl80211_key_attributes {
- * @NL80211_TXRATE_VHT: VHT rates allowed for TX rate selection,
- * see &struct nl80211_txrate_vht
- * @NL80211_TXRATE_GI: configure GI, see &enum nl80211_txrate_gi
-+ * @NL80211_TXRATE_HE: HE rates allowed for TX rate selection,
-+ * see &struct nl80211_txrate_he
-+ * @NL80211_TXRATE_HE_GI: configure HE GI, 0.8us, 1.6us and 3.2us.
-+ * @NL80211_TXRATE_HE_LTF: configure HE LTF, 1XLTF, 2XLTF and 4XLTF.
- * @__NL80211_TXRATE_AFTER_LAST: internal
- * @NL80211_TXRATE_MAX: highest TX rate attribute
- */
-@@ -4750,6 +4809,9 @@ enum nl80211_tx_rate_attributes {
- NL80211_TXRATE_HT,
- NL80211_TXRATE_VHT,
- NL80211_TXRATE_GI,
-+ NL80211_TXRATE_HE,
-+ NL80211_TXRATE_HE_GI,
-+ NL80211_TXRATE_HE_LTF,
-
- /* keep last */
- __NL80211_TXRATE_AFTER_LAST,
-@@ -4767,6 +4829,15 @@ struct nl80211_txrate_vht {
- __u16 mcs[NL80211_VHT_NSS_MAX];
- };
-
-+#define NL80211_HE_NSS_MAX 8
-+/**
-+ * struct nl80211_txrate_he - HE MCS/NSS txrate bitmap
-+ * @mcs: MCS bitmap table for each NSS (array index 0 for 1 stream, etc.)
-+ */
-+struct nl80211_txrate_he {
-+ __u16 mcs[NL80211_HE_NSS_MAX];
-+};
-+
- enum nl80211_txrate_gi {
- NL80211_TXRATE_DEFAULT_GI,
- NL80211_TXRATE_FORCE_SGI,
-@@ -5821,6 +5892,15 @@ enum nl80211_feature_flags {
- * handshake with PSK in AP mode (PSK is passed as part of the start AP
- * command).
- *
-+ * @NL80211_EXT_FEATURE_SAE_OFFLOAD_AP: Device wants to do SAE authentication
-+ * in AP mode (SAE password is passed as part of the start AP command).
-+ *
-+ * @NL80211_EXT_FEATURE_FILS_DISCOVERY: Driver/device supports FILS discovery
-+ * frames transmission
-+ *
-+ * @NL80211_EXT_FEATURE_UNSOL_BCAST_PROBE_RESP: Driver/device supports
-+ * unsolicited broadcast probe response transmission
-+ *
- * @NUM_NL80211_EXT_FEATURES: number of extended features.
- * @MAX_NL80211_EXT_FEATURES: highest extended feature index.
- */
-@@ -5878,6 +5958,9 @@ enum nl80211_ext_feature_index {
- NL80211_EXT_FEATURE_CONTROL_PORT_OVER_NL80211_TX_STATUS,
- NL80211_EXT_FEATURE_OPERATING_CHANNEL_VALIDATION,
- NL80211_EXT_FEATURE_4WAY_HANDSHAKE_AP_PSK,
-+ NL80211_EXT_FEATURE_SAE_OFFLOAD_AP,
-+ NL80211_EXT_FEATURE_FILS_DISCOVERY,
-+ NL80211_EXT_FEATURE_UNSOL_BCAST_PROBE_RESP,
-
- /* add new features before the definition below */
- NUM_NL80211_EXT_FEATURES,
-@@ -5992,6 +6075,8 @@ enum nl80211_timeout_reason {
- * @NL80211_SCAN_FLAG_FREQ_KHZ: report scan results with
- * %NL80211_ATTR_SCAN_FREQ_KHZ. This also means
- * %NL80211_ATTR_SCAN_FREQUENCIES will not be included.
-+ * @NL80211_SCAN_FLAG_COLOCATED_6GHZ: scan for colocated APs reported by
-+ * 2.4/5 GHz APs
- */
- enum nl80211_scan_flags {
- NL80211_SCAN_FLAG_LOW_PRIORITY = 1<<0,
-@@ -6008,6 +6093,7 @@ enum nl80211_scan_flags {
- NL80211_SCAN_FLAG_RANDOM_SN = 1<<11,
- NL80211_SCAN_FLAG_MIN_PREQ_CONTENT = 1<<12,
- NL80211_SCAN_FLAG_FREQ_KHZ = 1<<13,
-+ NL80211_SCAN_FLAG_COLOCATED_6GHZ = 1<<14,
- };
-
- /**
-@@ -6910,6 +6996,13 @@ enum nl80211_peer_measurement_ftm_resp {
- *
- * @NL80211_HE_OBSS_PD_ATTR_MIN_OFFSET: the OBSS PD minimum tx power offset.
- * @NL80211_HE_OBSS_PD_ATTR_MAX_OFFSET: the OBSS PD maximum tx power offset.
-+ * @NL80211_HE_OBSS_PD_ATTR_NON_SRG_MAX_OFFSET: the non-SRG OBSS PD maximum
-+ * tx power offset.
-+ * @NL80211_HE_OBSS_PD_ATTR_BSS_COLOR_BITMAP: bitmap that indicates the BSS color
-+ * values used by members of the SRG.
-+ * @NL80211_HE_OBSS_PD_ATTR_PARTIAL_BSSID_BITMAP: bitmap that indicates the partial
-+ * BSSID values used by members of the SRG.
-+ * @NL80211_HE_OBSS_PD_ATTR_SR_CTRL: The SR Control field of SRP element.
- *
- * @__NL80211_HE_OBSS_PD_ATTR_LAST: Internal
- * @NL80211_HE_OBSS_PD_ATTR_MAX: highest OBSS PD attribute.
-@@ -6919,6 +7012,10 @@ enum nl80211_obss_pd_attributes {
-
- NL80211_HE_OBSS_PD_ATTR_MIN_OFFSET,
- NL80211_HE_OBSS_PD_ATTR_MAX_OFFSET,
-+ NL80211_HE_OBSS_PD_ATTR_NON_SRG_MAX_OFFSET,
-+ NL80211_HE_OBSS_PD_ATTR_BSS_COLOR_BITMAP,
-+ NL80211_HE_OBSS_PD_ATTR_PARTIAL_BSSID_BITMAP,
-+ NL80211_HE_OBSS_PD_ATTR_SR_CTRL,
-
- /* keep last */
- __NL80211_HE_OBSS_PD_ATTR_LAST,
-@@ -6972,4 +7069,64 @@ enum nl80211_iftype_akm_attributes {
- NL80211_IFTYPE_AKM_ATTR_MAX = __NL80211_IFTYPE_AKM_ATTR_LAST - 1,
- };
-
-+/**
-+ * enum nl80211_fils_discovery_attributes - FILS discovery configuration
-+ * from IEEE Std 802.11ai-2016, Annex C.3 MIB detail.
-+ *
-+ * @__NL80211_FILS_DISCOVERY_ATTR_INVALID: Invalid
-+ *
-+ * @NL80211_FILS_DISCOVERY_ATTR_INT_MIN: Minimum packet interval (u32, TU).
-+ * Allowed range: 0..10000 (TU = Time Unit)
-+ * @NL80211_FILS_DISCOVERY_ATTR_INT_MAX: Maximum packet interval (u32, TU).
-+ * Allowed range: 0..10000 (TU = Time Unit)
-+ * @NL80211_FILS_DISCOVERY_ATTR_TMPL: Template data for FILS discovery action
-+ * frame including the headers.
-+ *
-+ * @__NL80211_FILS_DISCOVERY_ATTR_LAST: Internal
-+ * @NL80211_FILS_DISCOVERY_ATTR_MAX: highest attribute
-+ */
-+enum nl80211_fils_discovery_attributes {
-+ __NL80211_FILS_DISCOVERY_ATTR_INVALID,
-+
-+ NL80211_FILS_DISCOVERY_ATTR_INT_MIN,
-+ NL80211_FILS_DISCOVERY_ATTR_INT_MAX,
-+ NL80211_FILS_DISCOVERY_ATTR_TMPL,
-+
-+ /* keep last */
-+ __NL80211_FILS_DISCOVERY_ATTR_LAST,
-+ NL80211_FILS_DISCOVERY_ATTR_MAX = __NL80211_FILS_DISCOVERY_ATTR_LAST - 1
-+};
-+
-+/*
-+ * FILS discovery template minimum length with action frame headers and
-+ * mandatory fields.
-+ */
-+#define NL80211_FILS_DISCOVERY_TMPL_MIN_LEN 42
-+
-+/**
-+ * enum nl80211_unsol_bcast_probe_resp_attributes - Unsolicited broadcast probe
-+ * response configuration. Applicable only in 6GHz.
-+ *
-+ * @__NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INVALID: Invalid
-+ *
-+ * @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INT: Maximum packet interval (u32, TU).
-+ * Allowed range: 0..20 (TU = Time Unit). IEEE P802.11ax/D6.0
-+ * 26.17.2.3.2 (AP behavior for fast passive scanning).
-+ * @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_TMPL: Unsolicited broadcast probe response
-+ * frame template (binary).
-+ *
-+ * @__NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_LAST: Internal
-+ * @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_MAX: highest attribute
-+ */
-+enum nl80211_unsol_bcast_probe_resp_attributes {
-+ __NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INVALID,
-+
-+ NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INT,
-+ NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_TMPL,
-+
-+ /* keep last */
-+ __NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_LAST,
-+ NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_MAX =
-+ __NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_LAST - 1
-+};
- #endif /* __LINUX_NL80211_H */
projects / openwrt / openwrt.git / blobdiff