--- /dev/null
+--- a/arch/mips/ath79/mach-ap136.c
++++ b/arch/mips/ath79/mach-ap136.c
+@@ -18,23 +18,29 @@
+ *
+ */
+
+-#include <linux/pci.h>
+-#include <linux/ath9k_platform.h>
++#include <linux/platform_device.h>
++#include <linux/ar8216_platform.h>
+
+-#include "machtypes.h"
++#include <asm/mach-ath79/ar71xx_regs.h>
++
++#include "common.h"
++#include "pci.h"
++#include "dev-ap9x-pci.h"
+ #include "dev-gpio-buttons.h"
++#include "dev-eth.h"
+ #include "dev-leds-gpio.h"
+-#include "dev-spi.h"
++#include "dev-m25p80.h"
++#include "dev-nfc.h"
+ #include "dev-usb.h"
+ #include "dev-wmac.h"
+-#include "pci.h"
++#include "machtypes.h"
+
+-#define AP136_GPIO_LED_STATUS_RED 14
+-#define AP136_GPIO_LED_STATUS_GREEN 19
+ #define AP136_GPIO_LED_USB 4
+-#define AP136_GPIO_LED_WLAN_2G 13
+ #define AP136_GPIO_LED_WLAN_5G 12
++#define AP136_GPIO_LED_WLAN_2G 13
++#define AP136_GPIO_LED_STATUS_RED 14
+ #define AP136_GPIO_LED_WPS_RED 15
++#define AP136_GPIO_LED_STATUS_GREEN 19
+ #define AP136_GPIO_LED_WPS_GREEN 20
+
+ #define AP136_GPIO_BTN_WPS 16
+@@ -43,37 +49,39 @@
+ #define AP136_KEYS_POLL_INTERVAL 20 /* msecs */
+ #define AP136_KEYS_DEBOUNCE_INTERVAL (3 * AP136_KEYS_POLL_INTERVAL)
+
+-#define AP136_WMAC_CALDATA_OFFSET 0x1000
+-#define AP136_PCIE_CALDATA_OFFSET 0x5000
++#define AP136_MAC0_OFFSET 0
++#define AP136_MAC1_OFFSET 6
++#define AP136_WMAC_CALDATA_OFFSET 0x1000
++#define AP136_PCIE_CALDATA_OFFSET 0x5000
+
+ static struct gpio_led ap136_leds_gpio[] __initdata = {
+ {
+- .name = "qca:green:status",
++ .name = "ap136:green:status",
+ .gpio = AP136_GPIO_LED_STATUS_GREEN,
+ .active_low = 1,
+ },
+ {
+- .name = "qca:red:status",
++ .name = "ap136:red:status",
+ .gpio = AP136_GPIO_LED_STATUS_RED,
+ .active_low = 1,
+ },
+ {
+- .name = "qca:green:wps",
++ .name = "ap136:green:wps",
+ .gpio = AP136_GPIO_LED_WPS_GREEN,
+ .active_low = 1,
+ },
+ {
+- .name = "qca:red:wps",
++ .name = "ap136:red:wps",
+ .gpio = AP136_GPIO_LED_WPS_RED,
+ .active_low = 1,
+ },
+ {
+- .name = "qca:red:wlan-2g",
++ .name = "ap136:red:wlan-2g",
+ .gpio = AP136_GPIO_LED_WLAN_2G,
+ .active_low = 1,
+ },
+ {
+- .name = "qca:red:usb",
++ .name = "ap136:red:usb",
+ .gpio = AP136_GPIO_LED_USB,
+ .active_low = 1,
+ }
+@@ -98,65 +106,169 @@ static struct gpio_keys_button ap136_gpi
+ },
+ };
+
+-static struct ath79_spi_controller_data ap136_spi0_data = {
+- .cs_type = ATH79_SPI_CS_TYPE_INTERNAL,
+- .cs_line = 0,
++static struct ar8327_pad_cfg ap136_ar8327_pad0_cfg;
++static struct ar8327_pad_cfg ap136_ar8327_pad6_cfg;
++
++static struct ar8327_platform_data ap136_ar8327_data = {
++ .pad0_cfg = &ap136_ar8327_pad0_cfg,
++ .pad6_cfg = &ap136_ar8327_pad6_cfg,
++ .port0_cfg = {
++ .force_link = 1,
++ .speed = AR8327_PORT_SPEED_1000,
++ .duplex = 1,
++ .txpause = 1,
++ .rxpause = 1,
++ },
++ .port6_cfg = {
++ .force_link = 1,
++ .speed = AR8327_PORT_SPEED_1000,
++ .duplex = 1,
++ .txpause = 1,
++ .rxpause = 1,
++ },
+ };
+
+-static struct spi_board_info ap136_spi_info[] = {
++static struct mdio_board_info ap136_mdio0_info[] = {
+ {
+- .bus_num = 0,
+- .chip_select = 0,
+- .max_speed_hz = 25000000,
+- .modalias = "mx25l6405d",
+- .controller_data = &ap136_spi0_data,
+- }
++ .bus_id = "ag71xx-mdio.0",
++ .phy_addr = 0,
++ .platform_data = &ap136_ar8327_data,
++ },
+ };
+
+-static struct ath79_spi_platform_data ap136_spi_data = {
+- .bus_num = 0,
+- .num_chipselect = 1,
+-};
++static void __init ap136_gmac_setup(void)
++{
++ void __iomem *base;
++ u32 t;
+
+-#ifdef CONFIG_PCI
+-static struct ath9k_platform_data ap136_ath9k_data;
++ base = ioremap(QCA955X_GMAC_BASE, QCA955X_GMAC_SIZE);
+
+-static int ap136_pci_plat_dev_init(struct pci_dev *dev)
+-{
+- if (dev->bus->number == 1 && (PCI_SLOT(dev->devfn)) == 0)
+- dev->dev.platform_data = &ap136_ath9k_data;
++ t = __raw_readl(base + QCA955X_GMAC_REG_ETH_CFG);
+
+- return 0;
+-}
++ t &= ~(QCA955X_ETH_CFG_RGMII_EN | QCA955X_ETH_CFG_GE0_SGMII);
++ t |= QCA955X_ETH_CFG_RGMII_EN;
+
+-static void __init ap136_pci_init(u8 *eeprom)
+-{
+- memcpy(ap136_ath9k_data.eeprom_data, eeprom,
+- sizeof(ap136_ath9k_data.eeprom_data));
++ __raw_writel(t, base + QCA955X_GMAC_REG_ETH_CFG);
+
+- ath79_pci_set_plat_dev_init(ap136_pci_plat_dev_init);
+- ath79_register_pci();
++ iounmap(base);
+ }
+-#else
+-static inline void ap136_pci_init(void) {}
+-#endif /* CONFIG_PCI */
+
+-static void __init ap136_setup(void)
++static void __init ap136_common_setup(void)
+ {
+ u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
+
++ ath79_register_m25p80(NULL);
++
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(ap136_leds_gpio),
+ ap136_leds_gpio);
+ ath79_register_gpio_keys_polled(-1, AP136_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(ap136_gpio_keys),
+ ap136_gpio_keys);
+- ath79_register_spi(&ap136_spi_data, ap136_spi_info,
+- ARRAY_SIZE(ap136_spi_info));
++
+ ath79_register_usb();
+- ath79_register_wmac(art + AP136_WMAC_CALDATA_OFFSET);
+- ap136_pci_init(art + AP136_PCIE_CALDATA_OFFSET);
++ ath79_register_nfc();
++
++ ath79_register_wmac(art + AP136_WMAC_CALDATA_OFFSET, NULL);
++
++ ap136_gmac_setup();
++
++ ath79_register_mdio(0, 0x0);
++
++ ath79_init_mac(ath79_eth0_data.mac_addr, art + AP136_MAC0_OFFSET, 0);
++
++ mdiobus_register_board_info(ap136_mdio0_info,
++ ARRAY_SIZE(ap136_mdio0_info));
++
++ /* GMAC0 is connected to the RMGII interface */
++ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_RGMII;
++ ath79_eth0_data.phy_mask = BIT(0);
++ ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
++
++ ath79_register_eth(0);
++
++ /* GMAC1 is connected tot eh SGMII interface */
++ ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
++ ath79_eth1_data.speed = SPEED_1000;
++ ath79_eth1_data.duplex = DUPLEX_FULL;
++
++ ath79_register_eth(1);
++}
++
++static void __init ap136_010_setup(void)
++{
++ u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
++
++ /* GMAC0 of the AR8327 switch is connected to GMAC0 via RGMII */
++ ap136_ar8327_pad0_cfg.mode = AR8327_PAD_MAC_RGMII;
++ ap136_ar8327_pad0_cfg.txclk_delay_en = true;
++ ap136_ar8327_pad0_cfg.rxclk_delay_en = true;
++ ap136_ar8327_pad0_cfg.txclk_delay_sel = AR8327_CLK_DELAY_SEL1;
++ ap136_ar8327_pad0_cfg.rxclk_delay_sel = AR8327_CLK_DELAY_SEL2;
++
++ /* GMAC6 of the AR8327 switch is connected to GMAC1 via SGMII */
++ ap136_ar8327_pad6_cfg.mode = AR8327_PAD_MAC_SGMII;
++ ap136_ar8327_pad6_cfg.rxclk_delay_en = true;
++ ap136_ar8327_pad6_cfg.rxclk_delay_sel = AR8327_CLK_DELAY_SEL0;
++
++ ath79_eth0_pll_data.pll_1000 = 0xa6000000;
++ ath79_eth1_pll_data.pll_1000 = 0x03000101;
++
++ ap136_common_setup();
++ ap91_pci_init(art + AP136_PCIE_CALDATA_OFFSET, NULL);
+ }
+
+ MIPS_MACHINE(ATH79_MACH_AP136_010, "AP136-010",
+ "Atheros AP136-010 reference board",
+- ap136_setup);
++ ap136_010_setup);
++
++static void __init ap136_020_common_setup(void)
++{
++ /* GMAC0 of the AR8327 switch is connected to GMAC1 via SGMII */
++ ap136_ar8327_pad0_cfg.mode = AR8327_PAD_MAC_SGMII;
++ ap136_ar8327_pad0_cfg.sgmii_delay_en = true;
++
++ /* GMAC6 of the AR8327 switch is connected to GMAC0 via RGMII */
++ ap136_ar8327_pad6_cfg.mode = AR8327_PAD_MAC_RGMII;
++ ap136_ar8327_pad6_cfg.txclk_delay_en = true;
++ ap136_ar8327_pad6_cfg.rxclk_delay_en = true;
++ ap136_ar8327_pad6_cfg.txclk_delay_sel = AR8327_CLK_DELAY_SEL1;
++ ap136_ar8327_pad6_cfg.rxclk_delay_sel = AR8327_CLK_DELAY_SEL2;
++
++ ath79_eth0_pll_data.pll_1000 = 0x56000000;
++ ath79_eth1_pll_data.pll_1000 = 0x03000101;
++
++ ap136_common_setup();
++}
++
++static void __init ap136_020_setup(void)
++{
++ u8 *art = (u8 *) KSEG1ADDR(0x1fff0000);
++
++ ap136_020_common_setup();
++ ap91_pci_init(art + AP136_PCIE_CALDATA_OFFSET, NULL);
++}
++
++MIPS_MACHINE(ATH79_MACH_AP136_020, "AP136-020",
++ "Atheros AP136-020 reference board",
++ ap136_020_setup);
++
++/*
++ * AP135-020 is similar to AP136-020, any future AP135 specific init
++ * code can be added here.
++ */
++static void __init ap135_020_setup(void)
++{
++ ap136_leds_gpio[0].name = "ap135:green:status";
++ ap136_leds_gpio[1].name = "ap135:red:status";
++ ap136_leds_gpio[2].name = "ap135:green:wps";
++ ap136_leds_gpio[3].name = "ap135:red:wps";
++ ap136_leds_gpio[4].name = "ap135:red:wlan-2g";
++ ap136_leds_gpio[5].name = "ap135:red:usb";
++
++ ap136_020_common_setup();
++ ath79_register_pci();
++}
++
++MIPS_MACHINE(ATH79_MACH_AP135_020, "AP135-020",
++ "Atheros AP135-020 reference board",
++ ap135_020_setup);
+--- a/arch/mips/ath79/machtypes.h
++++ b/arch/mips/ath79/machtypes.h
+@@ -18,7 +18,9 @@ enum ath79_mach_type {
+ ATH79_MACH_GENERIC = 0,
+ ATH79_MACH_AP121, /* Atheros AP121 reference board */
+ ATH79_MACH_AP121_MINI, /* Atheros AP121-MINI reference board */
++ ATH79_MACH_AP135_020, /* Atheros AP135-020 reference board */
+ ATH79_MACH_AP136_010, /* Atheros AP136-010 reference board */
++ ATH79_MACH_AP136_020, /* Atheros AP136-020 reference board */
+ ATH79_MACH_AP81, /* Atheros AP81 reference board */
+ ATH79_MACH_DB120, /* Atheros DB120 reference board */
+ ATH79_MACH_PB44, /* Atheros PB44 reference board */
+--- a/arch/mips/ath79/Kconfig
++++ b/arch/mips/ath79/Kconfig
+@@ -16,16 +16,17 @@ config ATH79_MACH_AP121
+ Atheros AP121 reference board.
+
+ config ATH79_MACH_AP136
+- bool "Atheros AP136 reference board"
++ bool "Atheros AP136/AP135 reference board"
+ select SOC_QCA955X
+ select ATH79_DEV_GPIO_BUTTONS
+ select ATH79_DEV_LEDS_GPIO
++ select ATH79_DEV_NFC
+ select ATH79_DEV_SPI
+ select ATH79_DEV_USB
+ select ATH79_DEV_WMAC
+ help
+ Say 'Y' here if you want your kernel to support the
+- Atheros AP136 reference board.
++ Atheros AP136 or AP135 reference boards.
+
+ config ATH79_MACH_AP81
+ bool "Atheros AP81 reference board"
projects / openwrt / openwrt.git / blobdiff