brcm2708: rename target to bcm27xx

[openwrt/openwrt.git] / target / linux / brcm2708 / patches-4.19 / 950-0677-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch

diff --git a/target/linux/brcm2708/patches-4.19/950-0677-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch b/target/linux/brcm2708/patches-4.19/950-0677-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch
deleted file mode 100644 (file)
index 30fa9b3..0000000
--- a/target/linux/brcm2708/patches-4.19/950-0677-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch
+++ /dev/null
@@ -1,77 +0,0 @@
-From 2d8a780a994098f7c532b712abd7298e0bca5a12 Mon Sep 17 00:00:00 2001
-From: Dave Stevenson <dave.stevenson@raspberrypi.org>
-Date: Wed, 28 Aug 2019 13:34:30 +0100
-Subject: [PATCH] media: dt-bindings: Add binding for the Sony IMX219
- sensor
-
-The IMX219 is an 8MPix CSI2 sensor, supporting 2 or 4 data lanes.
-Document the binding for this device.
-
-Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
----
- .../devicetree/bindings/media/i2c/imx219.txt  | 59 +++++++++++++++++++
- 1 file changed, 59 insertions(+)
- create mode 100644 Documentation/devicetree/bindings/media/i2c/imx219.txt
-
---- /dev/null
-+++ b/Documentation/devicetree/bindings/media/i2c/imx219.txt
-@@ -0,0 +1,59 @@
-+* Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor
-+
-+The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor with
-+an active array size of 3280H x 2464V. It is programmable through I2C
-+interface. The I2C address is fixed to 0x10 as per sensor data sheet.
-+Image data is sent through MIPI CSI-2, which is configured as either 2 or 4
-+data lanes.
-+
-+Required Properties:
-+- compatible: value should be "sony,imx219" for imx219 sensor
-+- reg: I2C bus address of the device
-+- clocks: reference to the xclk input clock.
-+- clock-names: should be "xclk".
-+- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
-+- AVDD-supply: Analog voltage supply, 2.8 volts
-+- DVDD-supply: Digital core voltage supply, 1.2 volts
-+
-+Optional Properties:
-+- xclr-gpios: reference to the GPIO connected to the xclr pin, if any. Must be
-+            released after all supplies are applied.
-+            This is an active high signal to the imx219.
-+
-+The imx219 device node should contain one 'port' child node with
-+an 'endpoint' subnode. For further reading on port node refer to
-+Documentation/devicetree/bindings/media/video-interfaces.txt.
-+
-+Endpoint node required properties for CSI-2 connection are:
-+- remote-endpoint: a phandle to the bus receiver's endpoint node.
-+- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
-+- data-lanes: should be set to <1 2>, or  <1 2 3 4> (two or four lane CSI-2
-+  supported)
-+
-+Example:
-+      sensor@10 {
-+              compatible = "sony,imx219";
-+              reg = <0x10>;
-+              #address-cells = <1>;
-+              #size-cells = <0>;
-+              clocks = <&imx219_clk>;
-+              clock-names = "xclk";
-+              xclr-gpios = <&gpio_sensor 0 0>;
-+              DOVDD-supply = <&vgen4_reg>; /* 1.8v */
-+              AVDD-supply = <&vgen3_reg>;  /* 2.8v */
-+              DVDD-supply = <&vgen2_reg>;  /* 1.2v */
-+
-+              imx219_clk: camera-clk {
-+                      compatible = "fixed-clock";
-+                      #clock-cells = <0>;
-+                      clock-frequency = <24000000>;
-+              };
-+
-+              port {
-+                      sensor_out: endpoint {
-+                              remote-endpoint = <&csiss_in>;
-+                              clock-lanes = <0>;
-+                              data-lanes = <1 2>;
-+                      };
-+              };
-+      };