brcm2708: rename target to bcm27xx

[openwrt/openwrt.git] / target / linux / brcm2708 / patches-4.19 / 950-0806-ARM-dts-Remove-bcm2838-rpi-4-b.dts.patch

diff --git a/target/linux/brcm2708/patches-4.19/950-0806-ARM-dts-Remove-bcm2838-rpi-4-b.dts.patch b/target/linux/brcm2708/patches-4.19/950-0806-ARM-dts-Remove-bcm2838-rpi-4-b.dts.patch
deleted file mode 100644 (file)
index 7a0b8c5..0000000
--- a/target/linux/brcm2708/patches-4.19/950-0806-ARM-dts-Remove-bcm2838-rpi-4-b.dts.patch
+++ /dev/null
@@ -1,146 +0,0 @@
-From 8aa8fd89094952e3201b927fb846ba61b30cab6b Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil@raspberrypi.org>
-Date: Wed, 29 Jan 2020 11:29:06 +0000
-Subject: [PATCH] ARM: dts: Remove bcm2838-rpi-4-b.dts
-
-Upstream are not going to use the bcm2838 identifier, so begin the
-cleanup by removing the suggested upstream Pi 4 .dts file.
-
-Signed-off-by: Phil Elwell <phil@raspberrypi.org>
----
- arch/arm/boot/dts/Makefile            |   1 -
- arch/arm/boot/dts/bcm2838-rpi-4-b.dts | 118 --------------------------
- 2 files changed, 119 deletions(-)
- delete mode 100644 arch/arm/boot/dts/bcm2838-rpi-4-b.dts
-
---- a/arch/arm/boot/dts/Makefile
-+++ b/arch/arm/boot/dts/Makefile
-@@ -95,7 +95,6 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
-       bcm2836-rpi-2-b.dtb \
-       bcm2837-rpi-3-b.dtb \
-       bcm2837-rpi-3-b-plus.dtb \
--      bcm2838-rpi-4-b.dtb \
-       bcm2835-rpi-zero.dtb \
-       bcm2835-rpi-zero-w.dtb
- dtb-$(CONFIG_ARCH_BCM_5301X) += \
---- a/arch/arm/boot/dts/bcm2838-rpi-4-b.dts
-+++ /dev/null
-@@ -1,118 +0,0 @@
--// SPDX-License-Identifier: GPL-2.0
--/dts-v1/;
--#include "bcm2838.dtsi"
--#include "bcm2835-rpi.dtsi"
--#include "bcm2838-rpi.dtsi"
--
--/ {
--      compatible = "raspberrypi,4-model-b", "brcm,bcm2711";
--      model = "Raspberry Pi 4 Model B";
--
--      chosen {
--              /* 8250 auxiliary UART instead of pl011 */
--              stdout-path = "serial1:115200n8";
--      };
--
--      memory@0 {
--              reg = <0 0 0x40000000>;
--      };
--
--      leds {
--              act {
--                      gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
--              };
--
--              pwr {
--                      label = "PWR";
--                      gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
--              };
--      };
--
--      wifi_pwrseq: wifi-pwrseq {
--              compatible = "mmc-pwrseq-simple";
--              reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
--      };
--
--      sd_io_1v8_reg: sd_io_1v8_reg {
--              status = "okay";
--              compatible = "regulator-gpio";
--              vin-supply = <&vdd_5v0_reg>;
--              regulator-name = "vdd-sd-io";
--              regulator-min-microvolt = <1800000>;
--              regulator-max-microvolt = <3300000>;
--              regulator-boot-on;
--              regulator-always-on;
--              regulator-settling-time-us = <5000>;
--
--              gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
--              states = <1800000 0x1
--                        3300000 0x0>;
--      };
--};
--
--&firmware {
--      expgpio: gpio {
--              compatible = "raspberrypi,firmware-gpio";
--              gpio-controller;
--              #gpio-cells = <2>;
--              gpio-line-names = "BT_ON",
--                                "WL_ON",
--                                "PWR_LED_OFF",
--                                "GLOBAL_RESET",
--                                "VDD_SD_IO_SEL",
--                                "CAM_GPIO",
--                                "",
--                                "";
--              status = "okay";
--      };
--};
--
--&pwm1 {
--      pinctrl-names = "default";
--      pinctrl-0 = <&pwm0_gpio40 &pwm1_gpio41>;
--      status = "okay";
--};
--
--/* SDHCI is used to control the SDIO for wireless */
--&sdhci {
--      #address-cells = <1>;
--      #size-cells = <0>;
--      pinctrl-names = "default";
--      pinctrl-0 = <&emmc_gpio34>;
--      status = "okay";
--      bus-width = <4>;
--      non-removable;
--      mmc-pwrseq = <&wifi_pwrseq>;
--
--      brcmf: wifi@1 {
--              reg = <1>;
--              compatible = "brcm,bcm4329-fmac";
--      };
--};
--
--/* EMMC2 is used to drive the SD card */
--&emmc2 {
--      status = "okay";
--      broken-cd;
--      vqmmc-supply = <&sd_io_1v8_reg>;
--};
--
--/* uart0 communicates with the BT module */
--&uart0 {
--      pinctrl-names = "default";
--      pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32 &gpclk2_gpio43>;
--      status = "okay";
--
--      bluetooth {
--              compatible = "brcm,bcm43438-bt";
--              max-speed = <2000000>;
--              shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
--      };
--};
--
--/* uart1 is mapped to the pin header */
--&uart1 {
--      pinctrl-names = "default";
--      pinctrl-0 = <&uart1_gpio14>;
--      status = "okay";
--};