+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0-only OR MIT
-
-#include "qcom-ipq4019.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/soc/qcom,tcsr.h>
-
-/ {
- model = "Aruba AP-303H";
- compatible = "aruba,ap-303h";
-
- aliases {
- led-boot = &led_system_green;
- led-failsafe = &led_system_red;
- led-running = &led_system_green;
- led-upgrade = &led_system_amber;
- };
-
- memory {
- device_type = "memory";
- reg = <0x80000000 0x10000000>;
- };
-
- soc {
- rng@22000 {
- status = "okay";
- };
-
- mdio@90000 {
- status = "okay";
- pinctrl-0 = <&mdio_pins>;
- pinctrl-names = "default";
-
- reset-gpios = <&tlmm 19 GPIO_ACTIVE_LOW>;
- reset-delay-us = <2000>;
- };
-
- counter@4a1000 {
- compatible = "qcom,qca-gcnt";
- reg = <0x4a1000 0x4>;
- };
-
- ess_tcsr@1953000 {
- compatible = "qcom,tcsr";
- reg = <0x1953000 0x1000>;
- qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
- };
-
- tcsr@1949000 {
- compatible = "qcom,tcsr";
- reg = <0x1949000 0x100>;
- qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
- };
-
- tcsr@194b000 {
- compatible = "qcom,tcsr";
- reg = <0x194b000 0x100>;
- qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
- };
-
- tcsr@1957000 {
- compatible = "qcom,tcsr";
- reg = <0x1957000 0x100>;
- qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
- };
-
- usb2@60f8800 {
- status = "okay";
- };
-
- crypto@8e3a000 {
- status = "okay";
- };
-
- watchdog@b017000 {
- status = "okay";
- };
-
- i2c_0: i2c@78b7000 {
- pinctrl-0 = <&i2c_0_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- tpm@29 {
- /* No Driver */
- compatible = "atmel,at97sc3203";
- reg = <0x29>;
- read-only;
- };
-
- power-monitor@40 {
- /* No driver */
- compatible = "isl,isl28022";
- reg = <0x40>;
- };
- };
- };
-
- leds {
- compatible = "gpio-leds";
-
- wifi_green {
- label = "green:wifi";
- gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "phy0tpt";
- };
-
- wifi_amber {
- label = "amber:wifi";
- gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "phy1tpt";
- };
-
- pse {
- label = "green:pse";
- gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
- };
-
- led_system_red: system_red {
- label = "red:system";
- gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
- };
-
- led_system_green: system_green {
- label = "green:system";
- gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>;
- };
-
- led_system_amber: system_amber {
- label = "amber:system";
- gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
- };
- };
-
- keys {
- compatible = "gpio-keys";
-
- reset {
- label = "Reset button";
- gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
- linux,code = <KEY_RESTART>;
- };
- };
-};
-
-&blsp_dma {
- status = "okay";
-};
-
-&blsp1_uart1 {
- pinctrl-0 = <&serial_0_pins>;
- pinctrl-names = "default";
- status = "okay";
-};
-
-&blsp1_uart2 {
- /* Texas Instruments CC2540T BLE radio */
- pinctrl-0 = <&serial_1_pins>;
- pinctrl-names = "default";
- status = "okay";
-};
-
-&cryptobam {
- status = "okay";
-};
-
-&qpic_bam {
- status = "okay";
-};
-
-&tlmm {
- /*
- * In addition to the Pins listed below,
- * the following GPIOs have "features":
- * 39 - out - active low to force HW reset
- * 32 - out - active low to reset TPM
- * 43 - out - active low to reset BLE radio
- * 41 - out - pulse to set warm reset status
- * 34 - out - active low to enable PSE port
- * 22 - in - active low when 802.3at powered
- * 29 - in - active high when DC powered
- * 40 - in - active low when reset due to cold HW reset
- * 30 - in - active low when USB overcurrent detected
- * 35 - in - interrupt line for power monitor chip
- * 31 - in - active low when PSE port active
- */
- mdio_pins: mdio_pinmux {
- mux_1 {
- pins = "gpio6";
- function = "mdio";
- bias-pull-up;
- };
- mux_2 {
- pins = "gpio7";
- function = "mdc";
- bias-pull-up;
- };
- };
-
- spi_0_pins: spi_0_pinmux {
- pin {
- function = "blsp_spi0";
- pins = "gpio13", "gpio14", "gpio15";
- drive-strength = <12>;
- bias-disable;
- };
- pin_cs {
- function = "gpio";
- pins = "gpio12", "gpio59";
- drive-strength = <2>;
- bias-disable;
- output-high;
- };
- };
-
- i2c_0_pins: i2c_0_pinmux {
- mux {
- pins = "gpio20", "gpio21";
- function = "blsp_i2c0";
- drive-strength = <4>;
- bias-disable;
- };
- };
-
- serial_0_pins: serial_0_pinmux {
- mux {
- pins = "gpio16", "gpio17";
- function = "blsp_uart0";
- bias-disable;
- };
- };
-
- serial_1_pins: serial_1_pinmux {
- mux {
- pins = "gpio8", "gpio9";
- function = "blsp_uart1";
- bias-disable;
- };
- };
-
- usb-power {
- line-name = "USB-power";
- gpios = <23 GPIO_ACTIVE_HIGH>;
- gpio-hog;
- output-high;
- };
-};
-
-&blsp1_spi1 {
- pinctrl-0 = <&spi_0_pins>;
- pinctrl-names = "default";
- status = "okay";
- cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>, <&tlmm 59 GPIO_ACTIVE_HIGH>;
-
- flash@0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <24000000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- /*
- * There is no partition map for the NOR flash
- * in the stock firmware.
- *
- * All partitions here are based on offsets
- * found in the U-Boot GPL code and information
- * from smem.
- */
-
- partition@0 {
- label = "sbl1";
- reg = <0x0 0x40000>;
- read-only;
- };
-
- partition@40000 {
- label = "mibib";
- reg = <0x40000 0x20000>;
- read-only;
- };
-
- partition@60000 {
- label = "qsee";
- reg = <0x60000 0x60000>;
- read-only;
- };
-
- partition@c0000 {
- label = "cdt";
- reg = <0xc0000 0x10000>;
- read-only;
- };
-
- partition@d0000 {
- label = "ddrparams";
- reg = <0xd0000 0x10000>;
- read-only;
- };
-
- partition@e0000 {
- label = "appsblenv";
- reg = <0xe0000 0x10000>;
- read-only;
- };
-
- partition@f0000 {
- label = "appsbl";
- reg = <0xf0000 0x100000>;
- read-only;
- };
-
- partition@1e0000 {
- label = "ART";
- reg = <0x1f0000 0x10000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- precal_art_1000: precal@1000 {
- reg = <0x1000 0x2f20>;
- };
-
- precal_art_5000: precal@5000 {
- reg = <0x5000 0x2f20>;
- };
- };
- };
-
- partition@1f0000 {
- label = "osss";
- reg = <0x200000 0x170000>;
- read-only;
- };
-
- partition@200000 {
- label = "pds";
- reg = <0x370000 0x10000>;
- read-only;
- };
-
- partition@380000 {
- label = "apcd";
- reg = <0x380000 0x10000>;
- read-only;
- };
-
- partition@390000 {
- label = "mfginfo";
- reg = <0x390000 0x10000>;
- read-only;
-
- nvmem-layout {
- compatible = "fixed-layout";
- #address-cells = <1>;
- #size-cells = <1>;
-
- macaddr_mfginfo_1d: macaddr@1d {
- reg = <0x1d 0x6>;
- };
-
- macaddr_mfginfo_45: macaddr@45 {
- compatible = "mac-base";
- reg = <0x45 0x6>;
- #nvmem-cell-cells = <1>;
- };
- };
- };
-
- partition@3a0000 {
- label = "fcache";
- reg = <0x3a0000 0x10000>;
- read-only;
- };
-
- partition@3b0000 {
- /* Called osss1 in smem */
- label = "u-boot-env-bak";
- reg = <0x3b0000 0x10000>;
- read-only;
- };
-
- partition@3f0000 {
- label = "u-boot-env";
- reg = <0x3c0000 0x40000>;
- read-only;
- };
- };
- };
-
- flash@1 {
- status = "okay";
-
- compatible = "spi-nand";
- reg = <1>;
- spi-max-frequency = <24000000>;
-
- partitions {
- compatible = "fixed-partitions";
- #address-cells = <1>;
- #size-cells = <1>;
-
- partition@0 {
- /* 'aos0' in Aruba firmware */
- label = "aos0";
- reg = <0x0 0x2000000>;
- read-only;
- };
-
- partition@2000000 {
- /* 'aos1' in Aruba firmware */
- label = "ubi";
- reg = <0x2000000 0x2000000>;
- };
-
- partition@4000000 {
- label = "aruba-ubifs";
- reg = <0x4000000 0x4000000>;
- read-only;
- };
- };
- };
-};
-
-&usb2_hs_phy {
- status = "okay";
-};
-
-&gmac {
- status = "okay";
-};
-
-&switch {
- status = "okay";
-};
-
-&swport2 {
- status = "okay";
-
- label = "lan1";
-};
-
-&swport3 {
- status = "okay";
-
- label = "lan2";
-};
-
-&swport4 {
- status = "okay";
-
- label = "lan3";
-};
-
-&swport5 {
- status = "okay";
-
- label = "wan";
-};
-
-&wifi0 {
- status = "okay";
- nvmem-cell-names = "pre-calibration", "mac-address";
- nvmem-cells = <&precal_art_1000>, <&macaddr_mfginfo_45 0>;
- qcom,ath10k-calibration-variant = "Aruba-AP-303";
-};
-
-&wifi1 {
- status = "okay";
- nvmem-cell-names = "pre-calibration", "mac-address";
- nvmem-cells = <&precal_art_5000>, <&macaddr_mfginfo_45 1>;
- qcom,ath10k-calibration-variant = "Aruba-AP-303";
-};
projects / openwrt / openwrt.git / blobdiff