ipq806x: remove support for kernel 4.19

[openwrt/openwrt.git] / target / linux / ipq806x / files-4.19 / arch / arm / boot / dts / qcom-ipq8064-ap148.dts

diff --git a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
deleted file mode 100644 (file)
index 02f60c9..0000000
--- a/target/linux/ipq806x/files-4.19/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
+++ /dev/null
@@ -1,229 +0,0 @@
-#include "qcom-ipq8064-v1.0.dtsi"
-
-/ {
-       model = "Qualcomm Technologies, Inc. IPQ8064/AP-148";
-       compatible = "qcom,ipq8064-ap148", "qcom,ipq8064";
-
-       memory@0 {
-               reg = <0x42000000 0x1e000000>;
-               device_type = "memory";
-       };
-
-       reserved-memory {
-               #address-cells = <1>;
-               #size-cells = <1>;
-               ranges;
-               rsvd@41200000 {
-                       reg = <0x41200000 0x300000>;
-                       no-map;
-               };
-       };
-
-       aliases {
-               serial0 = &gsbi4_serial;
-               mdio-gpio0 = &mdio0;
-       };
-
-       chosen {
-               stdout-path = "serial0:115200n8";
-       };
-
-       soc {
-               mdio0: mdio {
-                       compatible = "virtual,mdio-gpio";
-                       #address-cells = <1>;
-                       #size-cells = <0>;
-                       gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
-                               <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
-                       pinctrl-0 = <&mdio0_pins>;
-                       pinctrl-names = "default";
-
-                       phy0: ethernet-phy@0 {
-                               reg = <0>;
-                               qca,ar8327-initvals = <
-                                       0x00004 0x7600000   /* PAD0_MODE */
-                                       0x00008 0x1000000   /* PAD5_MODE */
-                                       0x0000c 0x80        /* PAD6_MODE */
-                                       0x000e4 0x6a545     /* MAC_POWER_SEL */
-                                       0x000e0 0xc74164de  /* SGMII_CTRL */
-                                       0x0007c 0x4e        /* PORT0_STATUS */
-                                       0x00094 0x4e        /* PORT6_STATUS */
-                                       >;
-                       };
-
-                       phy4: ethernet-phy@4 {
-                               reg = <4>;
-                       };
-               };
-       };
-};
-
-&qcom_pinmux {
-       i2c4_pins: i2c4_pinmux {
-               pins = "gpio12", "gpio13";
-               function = "gsbi4";
-               bias-disable;
-       };
-
-       nand_pins: nand_pins {
-               disable {
-                       pins = "gpio34", "gpio35", "gpio36",
-                              "gpio37", "gpio38";
-                       function = "nand";
-                       drive-strength = <10>;
-                       bias-disable;
-               };
-
-               pullups {
-                       pins = "gpio39";
-                       function = "nand";
-                       drive-strength = <10>;
-                       bias-pull-up;
-               };
-
-               hold {
-                       pins = "gpio40", "gpio41", "gpio42",
-                              "gpio43", "gpio44", "gpio45",
-                              "gpio46", "gpio47";
-                       function = "nand";
-                       drive-strength = <10>;
-                       bias-bus-hold;
-               };
-       };
-
-       mdio0_pins: mdio0_pins {
-               mux {
-                       pins = "gpio0", "gpio1";
-                       function = "gpio";
-                       drive-strength = <8>;
-                       bias-disable;
-               };
-       };
-
-       rgmii2_pins: rgmii2_pins {
-               mux {
-                       pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32",
-                              "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62" ;
-                       function = "rgmii2";
-                       drive-strength = <8>;
-                       bias-disable;
-               };
-       };
-};
-
-&adm_dma {
-       status = "okay";
-};
-
-&gsbi4 {
-       qcom,mode = <GSBI_PROT_I2C_UART>;
-       status = "okay";
-
-       serial@16340000 {
-               status = "okay";
-       };
-
-       /*
-       * The i2c device on gsbi4 should not be enabled.
-       * On ipq806x designs gsbi4 i2c is meant for exclusive
-       * RPM usage. Turning this on in kernel manifests as
-       * i2c failure for the RPM.
-       */
-};
-
-&gsbi5 {
-       qcom,mode = <GSBI_PROT_SPI>;
-       status = "okay";
-
-       spi4: spi@1a280000 {
-               status = "okay";
-               spi-max-frequency = <50000000>;
-
-               pinctrl-0 = <&spi_pins>;
-               pinctrl-names = "default";
-
-               cs-gpios = <&qcom_pinmux 20 0>;
-
-               flash: m25p80@0 {
-                       compatible = "s25fl256s1";
-                       #address-cells = <1>;
-                       #size-cells = <1>;
-                       spi-max-frequency = <50000000>;
-                       reg = <0>;
-
-                       partitions {
-                               compatible = "qcom,smem";
-                       };
-               };
-       };
-};
-
-&usb3_0 {
-       status = "okay";
-};
-
-&usb3_1 {
-       status = "okay";
-};
-
-&pcie0 {
-       status = "okay";
-};
-
-&pcie1 {
-       status = "okay";
-       force_gen1 = <1>;
-};
-
-&nand {
-       status = "okay";
-
-       pinctrl-0 = <&nand_pins>;
-       pinctrl-names = "default";
-
-       cs0 {
-               reg = <0>;
-               compatible = "qcom,nandcs";
-
-               nand-ecc-strength = <4>;
-               nand-bus-width = <8>;
-               nand-ecc-step-size = <512>;
-
-               partitions {
-                       compatible = "qcom,smem";
-               };
-       };
-};
-
-&gmac1 {
-       status = "okay";
-       phy-mode = "rgmii";
-       qcom,id = <1>;
-
-       pinctrl-0 = <&rgmii2_pins>;
-       pinctrl-names = "default";
-
-       fixed-link {
-               speed = <1000>;
-               full-duplex;
-       };
-};
-
-&gmac2 {
-       status = "okay";
-       phy-mode = "sgmii";
-       qcom,id = <2>;
-
-       fixed-link {
-               speed = <1000>;
-               full-duplex;
-       };
-};
-
-&sata_phy {
-       status = "okay";
-};
-
-&sata {
-       status = "okay";
-};