--- /dev/null
+/*
+ * Copyright (C) 2013 Realtek Semiconductor Corp.
+ * All Rights Reserved.
+ *
+ * Unless you and Realtek execute a separate written software license
+ * agreement governing use of this software, this software is licensed
+ * to you under the terms of the GNU General Public License version 2,
+ * available at https://www.gnu.org/licenses/old-licenses/gpl-2.0.txt
+ *
+ * $Revision: 76306 $
+ * $Date: 2017-03-08 15:13:58 +0800 (週三, 08 三月 2017) $
+ *
+ * Purpose : RTL8367C switch high-level API for RTL8367C
+ * Feature : LED related functions
+ *
+ */
+#include <rtl8367c_asicdrv_led.h>
+/* Function Name:
+ * rtl8367c_setAsicLedIndicateInfoConfig
+ * Description:
+ * Set Leds indicated information mode
+ * Input:
+ * ledno - LED group number. There are 1 to 1 led mapping to each port in each led group
+ * config - Support 16 types configuration
+ * Output:
+ * None
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * RT_ERR_OUT_OF_RANGE - input parameter out of range
+ * Note:
+ * The API can set LED indicated information configuration for each LED group with 1 to 1 led mapping to each port.
+ * Definition LED Statuses Description
+ * 0000 LED_Off LED pin Tri-State.
+ * 0001 Dup/Col Collision, Full duplex Indicator. Blinking every 43ms when collision happens. Low for full duplex, and high for half duplex mode.
+ * 0010 Link/Act Link, Activity Indicator. Low for link established. Link/Act Blinks every 43ms when the corresponding port is transmitting or receiving.
+ * 0011 Spd1000 1000Mb/s Speed Indicator. Low for 1000Mb/s.
+ * 0100 Spd100 100Mb/s Speed Indicator. Low for 100Mb/s.
+ * 0101 Spd10 10Mb/s Speed Indicator. Low for 10Mb/s.
+ * 0110 Spd1000/Act 1000Mb/s Speed/Activity Indicator. Low for 1000Mb/s. Blinks every 43ms when the corresponding port is transmitting or receiving.
+ * 0111 Spd100/Act 100Mb/s Speed/Activity Indicator. Low for 100Mb/s. Blinks every 43ms when the corresponding port is transmitting or receiving.
+ * 1000 Spd10/Act 10Mb/s Speed/Activity Indicator. Low for 10Mb/s. Blinks every 43ms when the corresponding port is transmitting or receiving.
+ * 1001 Spd100 (10)/Act 10/100Mb/s Speed/Activity Indicator. Low for 10/100Mb/s. Blinks every 43ms when the corresponding port is transmitting or receiving.
+ * 1010 Fiber Fiber link Indicator. Low for Fiber.
+ * 1011 Fault Auto-negotiation Fault Indicator. Low for Fault.
+ * 1100 Link/Rx Link, Activity Indicator. Low for link established. Link/Rx Blinks every 43ms when the corresponding port is transmitting.
+ * 1101 Link/Tx Link, Activity Indicator. Low for link established. Link/Tx Blinks every 43ms when the corresponding port is receiving.
+ * 1110 Master Link on Master Indicator. Low for link Master established.
+ * 1111 LED_Force Force LED output, LED output value reference
+ */
+ret_t rtl8367c_setAsicLedIndicateInfoConfig(rtk_uint32 ledno, rtk_uint32 config)
+{
+ ret_t retVal;
+ CONST rtk_uint16 bits[RTL8367C_LEDGROUPNO] = {RTL8367C_LED0_CFG_MASK, RTL8367C_LED1_CFG_MASK, RTL8367C_LED2_CFG_MASK};
+
+ if(ledno >= RTL8367C_LEDGROUPNO)
+ return RT_ERR_OUT_OF_RANGE;
+
+ if(config >= LEDCONF_END)
+ return RT_ERR_OUT_OF_RANGE;
+
+ retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_CONFIGURATION, RTL8367C_LED_CONFIG_SEL_OFFSET, 0);
+ if(retVal != RT_ERR_OK)
+ return retVal;
+
+ return rtl8367c_setAsicRegBits(RTL8367C_REG_LED_CONFIGURATION, bits[ledno], config);
+}
+/* Function Name:
+ * rtl8367c_getAsicLedIndicateInfoConfig
+ * Description:
+ * Get Leds indicated information mode
+ * Input:
+ * ledno - LED group number. There are 1 to 1 led mapping to each port in each led group
+ * pConfig - Support 16 types configuration
+ * Output:
+ * None
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * RT_ERR_OUT_OF_RANGE - input parameter out of range
+ * Note:
+ * None
+ */
+ret_t rtl8367c_getAsicLedIndicateInfoConfig(rtk_uint32 ledno, rtk_uint32* pConfig)
+{
+ CONST rtk_uint16 bits[RTL8367C_LEDGROUPNO]= {RTL8367C_LED0_CFG_MASK, RTL8367C_LED1_CFG_MASK, RTL8367C_LED2_CFG_MASK};
+
+ if(ledno >= RTL8367C_LEDGROUPNO)
+ return RT_ERR_OUT_OF_RANGE;
+
+ /* Get register value */
+ return rtl8367c_getAsicRegBits(RTL8367C_REG_LED_CONFIGURATION, bits[ledno], pConfig);
+}
+/* Function Name:
+ * rtl8367c_setAsicLedGroupMode
+ * Description:
+ * Set Led Group mode
+ * Input:
+ * mode - LED mode
+ * Output:
+ * None
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * RT_ERR_OUT_OF_RANGE - input parameter out of range
+ * Note:
+ * None
+ */
+ret_t rtl8367c_setAsicLedGroupMode(rtk_uint32 mode)
+{
+ ret_t retVal;
+
+ /* Invalid input parameter */
+ if(mode >= RTL8367C_LED_MODE_END)
+ return RT_ERR_OUT_OF_RANGE;
+
+ retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_CONFIGURATION, RTL8367C_LED_CONFIG_SEL_OFFSET, 1);
+ if(retVal != RT_ERR_OK)
+ return retVal;
+
+ return rtl8367c_setAsicRegBits(RTL8367C_REG_LED_CONFIGURATION, RTL8367C_DATA_LED_MASK, mode);
+}
+/* Function Name:
+ * rtl8367c_getAsicLedGroupMode
+ * Description:
+ * Get Led Group mode
+ * Input:
+ * pMode - LED mode
+ * Output:
+ * None
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * Note:
+ * None
+ */
+ret_t rtl8367c_getAsicLedGroupMode(rtk_uint32* pMode)
+{
+ ret_t retVal;
+ rtk_uint32 regData;
+
+ retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_LED_CONFIGURATION, RTL8367C_LED_CONFIG_SEL_OFFSET, ®Data);
+ if(retVal != RT_ERR_OK)
+ return retVal;
+
+ if(regData!=1)
+ return RT_ERR_FAILED;
+
+ return rtl8367c_getAsicRegBits(RTL8367C_REG_LED_CONFIGURATION, RTL8367C_DATA_LED_MASK, pMode);
+}
+/* Function Name:
+ * rtl8367c_setAsicForceLeds
+ * Description:
+ * Set group LED mode
+ * Input:
+ * port - Physical port number (0~7)
+ * group - LED group number
+ * mode - LED mode
+ * Output:
+ * None
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * RT_ERR_PORT_ID - Invalid port number
+ * RT_ERR_OUT_OF_RANGE - input parameter out of range
+ * Note:
+ * None
+ */
+ret_t rtl8367c_setAsicForceLed(rtk_uint32 port, rtk_uint32 group, rtk_uint32 mode)
+{
+ rtk_uint16 regAddr;
+ ret_t retVal;
+
+ /* Invalid input parameter */
+ if(port > RTL8367C_PORTIDMAX)
+ return RT_ERR_PORT_ID;
+
+ if(group >= RTL8367C_LEDGROUPNO)
+ return RT_ERR_OUT_OF_RANGE;
+
+ if(mode >= LEDFORCEMODE_END)
+ return RT_ERR_OUT_OF_RANGE;
+ /* Set Related Registers */
+ if(port < 8){
+ regAddr = RTL8367C_LED_FORCE_MODE_BASE + (group << 1);
+ if((retVal = rtl8367c_setAsicRegBits(regAddr, 0x3 << (port * 2), mode)) != RT_ERR_OK)
+ return retVal;
+ }else if(port >= 8){
+ regAddr = RTL8367C_REG_CPU_FORCE_LED0_CFG1 + (group << 1);
+ if((retVal = rtl8367c_setAsicRegBits(regAddr, 0x3 << ((port-8) * 2), mode)) != RT_ERR_OK)
+ return retVal;
+ }
+
+ return RT_ERR_OK;
+}
+/* Function Name:
+ * rtl8367c_getAsicForceLed
+ * Description:
+ * Get group LED mode
+ * Input:
+ * port - Physical port number (0~7)
+ * group - LED group number
+ * pMode - LED mode
+ * Output:
+ * None
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * RT_ERR_PORT_ID - Invalid port number
+ * RT_ERR_OUT_OF_RANGE - input parameter out of range
+ * Note:
+ * None
+ */
+ret_t rtl8367c_getAsicForceLed(rtk_uint32 port, rtk_uint32 group, rtk_uint32* pMode)
+{
+ rtk_uint16 regAddr;
+ ret_t retVal;
+
+ /* Invalid input parameter */
+ if(port > RTL8367C_PORTIDMAX)
+ return RT_ERR_PORT_ID;
+
+ if(group >= RTL8367C_LEDGROUPNO)
+ return RT_ERR_INPUT;
+
+ /* Get Related Registers */
+ if(port < 8){
+ regAddr = RTL8367C_LED_FORCE_MODE_BASE + (group << 1);
+ if((retVal = rtl8367c_getAsicRegBits(regAddr, 0x3 << (port * 2), pMode)) != RT_ERR_OK)
+ return retVal;
+ }else if(port >= 8){
+ regAddr = RTL8367C_REG_CPU_FORCE_LED0_CFG1 + (group << 1);
+ if((retVal = rtl8367c_getAsicRegBits(regAddr, 0x3 << ((port-8) * 2), pMode)) != RT_ERR_OK)
+ return retVal;
+ }
+
+ return RT_ERR_OK;
+}
+/* Function Name:
+ * rtl8367c_setAsicForceGroupLed
+ * Description:
+ * Turn on/off Led of all ports
+ * Input:
+ * group - LED group number
+ * mode - 0b00:normal mode, 0b01:force blink, 0b10:force off, 0b11:force on
+ * Output:
+ * None
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * RT_ERR_OUT_OF_RANGE - input parameter out of range
+ * Note:
+ * None
+ */
+ret_t rtl8367c_setAsicForceGroupLed(rtk_uint32 groupmask, rtk_uint32 mode)
+{
+ ret_t retVal;
+ rtk_uint32 i,bitmask;
+ CONST rtk_uint16 bits[3]= {0x0004,0x0010,0x0040};
+
+ /* Invalid input parameter */
+ if(groupmask > RTL8367C_LEDGROUPMASK)
+ return RT_ERR_OUT_OF_RANGE;
+
+ if(mode >= LEDFORCEMODE_END)
+ return RT_ERR_OUT_OF_RANGE;
+
+ bitmask = 0;
+ for(i = 0; i < RTL8367C_LEDGROUPNO; i++)
+ {
+ if(groupmask & (1 << i))
+ {
+ bitmask = bitmask | bits[i];
+ }
+
+ }
+
+ retVal = rtl8367c_setAsicRegBits(RTL8367C_LED_FORCE_CTRL, RTL8367C_LED_FORCE_MODE_MASK, bitmask);
+
+ retVal = rtl8367c_setAsicRegBits(RTL8367C_LED_FORCE_CTRL, RTL8367C_FORCE_MODE_MASK, mode);
+
+ if(LEDFORCEMODE_NORMAL == mode)
+ retVal = rtl8367c_setAsicRegBits(RTL8367C_LED_FORCE_CTRL, RTL8367C_LED_FORCE_MODE_MASK, 0);
+
+ return retVal;
+}
+/* Function Name:
+ * rtl8367c_getAsicForceGroupLed
+ * Description:
+ * Turn on/off Led of all ports
+ * Input:
+ * group - LED group number
+ * pMode - 0b00:normal mode, 0b01:force blink, 0b10:force off, 0b11:force on
+ * Output:
+ * None
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * Note:
+ * None
+ */
+ret_t rtl8367c_getAsicForceGroupLed(rtk_uint32* groupmask, rtk_uint32* pMode)
+{
+ ret_t retVal;
+ rtk_uint32 i,regData;
+ CONST rtk_uint16 bits[3] = {0x0004,0x0010,0x0040};
+
+ /* Get Related Registers */
+ if((retVal = rtl8367c_getAsicRegBits(RTL8367C_LED_FORCE_CTRL, RTL8367C_LED_FORCE_MODE_MASK, ®Data)) != RT_ERR_OK)
+ return retVal;
+
+ for(i = 0; i< RTL8367C_LEDGROUPNO; i++)
+ {
+ if((regData & bits[i]) == bits[i])
+ {
+ *groupmask = *groupmask | (1 << i);
+ }
+ }
+
+ return rtl8367c_getAsicRegBits(RTL8367C_LED_FORCE_CTRL, RTL8367C_FORCE_MODE_MASK, pMode);
+}
+/* Function Name:
+ * rtl8367c_setAsicLedBlinkRate
+ * Description:
+ * Set led blinking rate at mode 0 to mode 3
+ * Input:
+ * blinkRate - Support 6 blink rates
+ * Output:
+ * None
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * RT_ERR_OUT_OF_RANGE - input parameter out of range
+ * Note:
+ * LED blink rate can be at 43ms, 84ms, 120ms, 170ms, 340ms and 670ms
+ */
+ret_t rtl8367c_setAsicLedBlinkRate(rtk_uint32 blinkRate)
+{
+ if(blinkRate >= LEDBLINKRATE_END)
+ return RT_ERR_OUT_OF_RANGE;
+
+ return rtl8367c_setAsicRegBits(RTL8367C_REG_LED_MODE, RTL8367C_SEL_LEDRATE_MASK, blinkRate);
+}
+/* Function Name:
+ * rtl8367c_getAsicLedBlinkRate
+ * Description:
+ * Get led blinking rate at mode 0 to mode 3
+ * Input:
+ * pBlinkRate - Support 6 blink rates
+ * Output:
+ * None
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * Note:
+ * None
+ */
+ret_t rtl8367c_getAsicLedBlinkRate(rtk_uint32* pBlinkRate)
+{
+ return rtl8367c_getAsicRegBits(RTL8367C_REG_LED_MODE, RTL8367C_SEL_LEDRATE_MASK, pBlinkRate);
+}
+/* Function Name:
+ * rtl8367c_setAsicLedForceBlinkRate
+ * Description:
+ * Set LEd blinking rate for force mode led
+ * Input:
+ * blinkRate - Support 6 blink rates
+ * Output:
+ * None
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * RT_ERR_OUT_OF_RANGE - input parameter out of range
+ * Note:
+ * None
+ */
+ret_t rtl8367c_setAsicLedForceBlinkRate(rtk_uint32 blinkRate)
+{
+ if(blinkRate >= LEDFORCERATE_END)
+ return RT_ERR_OUT_OF_RANGE;
+
+ return rtl8367c_setAsicRegBits(RTL8367C_REG_LED_MODE, RTL8367C_FORCE_RATE_MASK, blinkRate);
+}
+/* Function Name:
+ * rtl8367c_getAsicLedForceBlinkRate
+ * Description:
+ * Get LED blinking rate for force mode led
+ * Input:
+ * pBlinkRate - Support 6 blink rates
+ * Output:
+ * None
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * Note:
+ * None
+ */
+ret_t rtl8367c_getAsicLedForceBlinkRate(rtk_uint32* pBlinkRate)
+{
+ return rtl8367c_getAsicRegBits(RTL8367C_REG_LED_MODE, RTL8367C_FORCE_RATE_MASK, pBlinkRate);
+}
+
+/*
+@func ret_t | rtl8367c_setAsicLedGroupEnable | Turn on/off Led of all system ports
+@parm rtk_uint32 | group | LED group id.
+@parm rtk_uint32 | portmask | LED port mask.
+@rvalue RT_ERR_OK | Success.
+@rvalue RT_ERR_SMI | SMI access error.
+@rvalue RT_ERR_PORT_ID | Invalid port number.
+@rvalue RT_ERR_INPUT | Invalid input value.
+@comm
+ The API can turn on/off leds of dedicated port while indicated information configuration of LED group is set to force mode.
+ */
+ret_t rtl8367c_setAsicLedGroupEnable(rtk_uint32 group, rtk_uint32 portmask)
+{
+ ret_t retVal;
+ rtk_uint32 regAddr;
+ rtk_uint32 regDataMask;
+
+ if ( group >= RTL8367C_LEDGROUPNO )
+ return RT_ERR_INPUT;
+
+ regAddr = RTL8367C_REG_PARA_LED_IO_EN1 + group/2;
+ regDataMask = 0xFF << ((group%2)*8);
+ retVal = rtl8367c_setAsicRegBits(regAddr, regDataMask, portmask&0xff);
+ if(retVal != RT_ERR_OK)
+ return retVal;
+
+ regAddr = RTL8367C_REG_PARA_LED_IO_EN3;
+ regDataMask = 0x3 << (group*2);
+ retVal = rtl8367c_setAsicRegBits(regAddr, regDataMask, (portmask>>8)&0x7);
+ if(retVal != RT_ERR_OK)
+ return retVal;
+
+
+ return RT_ERR_OK;
+}
+
+/*
+@func ret_t | rtl8367c_getAsicLedGroupEnable | Get on/off status of Led of all system ports
+@parm rtk_uint32 | group | LED group id.
+@parm rtk_uint32 | *portmask | LED port mask.
+@rvalue RT_ERR_OK | Success.
+@rvalue RT_ERR_SMI | SMI access error.
+@rvalue RT_ERR_PORT_ID | Invalid port number.
+@rvalue RT_ERR_INPUT | Invalid input value.
+@comm
+ The API can turn on/off leds of dedicated port while indicated information configuration of LED group is set to force mode.
+ */
+ret_t rtl8367c_getAsicLedGroupEnable(rtk_uint32 group, rtk_uint32 *portmask)
+{
+ ret_t retVal;
+ rtk_uint32 regAddr;
+ rtk_uint32 regDataMask,regData;
+
+ if ( group >= RTL8367C_LEDGROUPNO )
+ return RT_ERR_INPUT;
+
+ regAddr = RTL8367C_REG_PARA_LED_IO_EN1 + group/2;
+ regDataMask = 0xFF << ((group%2)*8);
+ retVal = rtl8367c_getAsicRegBits(regAddr, regDataMask, portmask);
+ if(retVal != RT_ERR_OK)
+ return retVal;
+
+
+ regAddr = RTL8367C_REG_PARA_LED_IO_EN3;
+ regDataMask = 0x3 << (group*2);
+ retVal = rtl8367c_getAsicRegBits(regAddr, regDataMask, ®Data);
+ if(retVal != RT_ERR_OK)
+ return retVal;
+
+ *portmask = (regData << 8) | *portmask;
+
+ return RT_ERR_OK;
+}
+
+/*
+@func ret_t | rtl8367c_setAsicLedOperationMode | Set LED operation mode
+@parm rtk_uint32 | mode | LED mode. 1:scan mode 1, 2:parallel mode, 3:mdx mode (serial mode)
+@rvalue RT_ERR_OK | Success.
+@rvalue RT_ERR_SMI | SMI access error.
+@rvalue RT_ERR_INPUT | Invalid input value.
+@comm
+ The API can turn on/off led serial mode and set signal to active high/low.
+ */
+ret_t rtl8367c_setAsicLedOperationMode(rtk_uint32 mode)
+{
+ ret_t retVal;
+
+ /* Invalid input parameter */
+ if( mode >= LEDOP_END)
+ return RT_ERR_INPUT;
+
+ switch(mode)
+ {
+ case LEDOP_PARALLEL:
+ if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_LED_SELECT_OFFSET, 0))!= RT_ERR_OK)
+ return retVal;
+ /*Disable serial CLK mode*/
+ if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SCAN0_LED_IO_EN1,RTL8367C_LED_SERI_CLK_EN_OFFSET, 0))!= RT_ERR_OK)
+ return retVal;
+ /*Disable serial DATA mode*/
+ if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SCAN0_LED_IO_EN1,RTL8367C_LED_SERI_DATA_EN_OFFSET, 0))!= RT_ERR_OK)
+ return retVal;
+ break;
+ case LEDOP_SERIAL:
+ if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_LED_SELECT_OFFSET, 1))!= RT_ERR_OK)
+ return retVal;
+ /*Enable serial CLK mode*/
+ if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SCAN0_LED_IO_EN1,RTL8367C_LED_SERI_CLK_EN_OFFSET, 1))!= RT_ERR_OK)
+ return retVal;
+ /*Enable serial DATA mode*/
+ if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_SCAN0_LED_IO_EN1,RTL8367C_LED_SERI_DATA_EN_OFFSET, 1))!= RT_ERR_OK)
+ return retVal;
+ break;
+ default:
+ return RT_ERR_INPUT;
+ break;
+ }
+
+ return RT_ERR_OK;
+}
+
+
+/*
+@func ret_t | rtl8367c_getAsicLedOperationMode | Get LED OP mode setup
+@parm rtk_uint32*| mode | LED mode. 1:scan mode 1, 2:parallel mode, 3:mdx mode (serial mode)
+@rvalue RT_ERR_OK | Success.
+@rvalue RT_ERR_SMI | SMI access error.
+@rvalue RT_ERR_INPUT | Invalid input value.
+@comm
+ The API can get LED serial mode setup and get signal active high/low.
+ */
+ret_t rtl8367c_getAsicLedOperationMode(rtk_uint32 *mode)
+{
+ ret_t retVal;
+ rtk_uint32 regData;
+
+ if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_LED_SELECT_OFFSET, ®Data))!= RT_ERR_OK)
+ return retVal;
+
+ if (regData == 1)
+ *mode = LEDOP_SERIAL;
+ else if (regData == 0)
+ *mode = LEDOP_PARALLEL;
+ else
+ return RT_ERR_FAILED;
+
+ return RT_ERR_OK;
+}
+
+/*
+@func ret_t | rtl8367c_setAsicLedSerialModeConfig | Set LED serial mode
+@parm rtk_uint32 | active | Active High or Low.
+@rvalue RT_ERR_OK | Success.
+@rvalue RT_ERR_SMI | SMI access error.
+@rvalue RT_ERR_INPUT | Invalid input value.
+@comm
+ The API can turn on/off led serial mode and set signal to active high/low.
+ */
+ret_t rtl8367c_setAsicLedSerialModeConfig(rtk_uint32 active, rtk_uint32 serimode)
+{
+ ret_t retVal;
+
+ /* Invalid input parameter */
+ if( active >= LEDSERACT_MAX)
+ return RT_ERR_INPUT;
+ if( serimode >= LEDSER_MAX)
+ return RT_ERR_INPUT;
+
+ /* Set Active High or Low */
+ if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_SERI_LED_ACT_LOW_OFFSET, active)) != RT_ERR_OK)
+ return retVal;
+
+ /*set to 8G mode (not 16G mode)*/
+ if((retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_MODE, RTL8367C_DLINK_TIME_OFFSET, serimode))!= RT_ERR_OK)
+ return retVal;
+
+
+ return RT_ERR_OK;
+}
+
+
+/*
+@func ret_t | rtl8367c_getAsicLedSerialModeConfig | Get LED serial mode setup
+@parm rtk_uint32*| active | Active High or Low.
+@rvalue RT_ERR_OK | Success.
+@rvalue RT_ERR_SMI | SMI access error.
+@rvalue RT_ERR_INPUT | Invalid input value.
+@comm
+ The API can get LED serial mode setup and get signal active high/low.
+ */
+ret_t rtl8367c_getAsicLedSerialModeConfig(rtk_uint32 *active, rtk_uint32 *serimode)
+{
+ ret_t retVal;
+
+ if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_SERI_LED_ACT_LOW_OFFSET, active))!= RT_ERR_OK)
+ return retVal;
+
+ /*get to 8G mode (not 16G mode)*/
+ if((retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_LED_MODE, RTL8367C_DLINK_TIME_OFFSET, serimode))!= RT_ERR_OK)
+ return retVal;
+
+ return RT_ERR_OK;
+}
+
+
+/*
+@func ret_t | rtl8367c_setAsicLedOutputEnable | Set LED output enable
+@parm rtk_uint32 | enabled | enable or disalbe.
+@rvalue RT_ERR_OK | Success.
+@rvalue RT_ERR_SMI | SMI access error.
+@rvalue RT_ERR_INPUT | Invalid input value.
+@comm
+ The API can turn on/off LED output Enable
+ */
+ret_t rtl8367c_setAsicLedOutputEnable(rtk_uint32 enabled)
+{
+ ret_t retVal;
+ rtk_uint32 regdata;
+
+ if (enabled == 1)
+ regdata = 0;
+ else
+ regdata = 1;
+
+ /* Enable/Disable H/W IGMP/MLD */
+ retVal = rtl8367c_setAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_LED_IO_DISABLE_OFFSET, regdata);
+
+ return retVal;
+}
+
+
+/*
+@func ret_t | rtl8367c_getAsicLedOutputEnable | Get LED serial mode setup
+@parm rtk_uint32*| active | Active High or Low.
+@rvalue RT_ERR_OK | Success.
+@rvalue RT_ERR_SMI | SMI access error.
+@rvalue RT_ERR_INPUT | Invalid input value.
+@comm
+ The API can get LED serial mode setup and get signal active high/low.
+ */
+ret_t rtl8367c_getAsicLedOutputEnable(rtk_uint32 *ptr_enabled)
+{
+ ret_t retVal;
+ rtk_uint32 regdata;
+
+ retVal = rtl8367c_getAsicRegBit(RTL8367C_REG_LED_SYS_CONFIG, RTL8367C_LED_IO_DISABLE_OFFSET, ®data);
+ if (retVal != RT_ERR_OK)
+ return retVal;
+
+ if (regdata == 1)
+ *ptr_enabled = 0;
+ else
+ *ptr_enabled = 1;
+
+ return RT_ERR_OK;
+}
+
+/* Function Name:
+ * rtl8367c_setAsicLedSerialOutput
+ * Description:
+ * Set serial LED output group and portmask.
+ * Input:
+ * output - Serial LED output group
+ * pmask - Serial LED output portmask
+ * Output:
+ * None
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * RT_ERR_OUT_OF_RANGE - input parameter out of range
+ * Note:
+ * None
+ */
+ret_t rtl8367c_setAsicLedSerialOutput(rtk_uint32 output, rtk_uint32 pmask)
+{
+ ret_t retVal;
+
+ retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SERIAL_LED_CTRL, RTL8367C_SERIAL_LED_GROUP_NUM_MASK, output);
+ if (retVal != RT_ERR_OK)
+ return retVal;
+
+ retVal = rtl8367c_setAsicRegBits(RTL8367C_REG_SERIAL_LED_CTRL, RTL8367C_SERIAL_LED_PORT_EN_MASK, pmask);
+ if (retVal != RT_ERR_OK)
+ return retVal;
+
+ return RT_ERR_OK;
+}
+
+/* Function Name:
+ * rtl8367c_getAsicLedSerialOutput
+ * Description:
+ * Get serial LED output group and portmask.
+ * Input:
+ * None
+ * Output:
+ * pOutput - Serial LED output group
+ * pPmask - Serial LED output portmask
+ * Return:
+ * RT_ERR_OK - Success
+ * RT_ERR_SMI - SMI access error
+ * RT_ERR_OUT_OF_RANGE - input parameter out of range
+ * Note:
+ * None
+ */
+ret_t rtl8367c_getAsicLedSerialOutput(rtk_uint32 *pOutput, rtk_uint32 *pPmask)
+{
+ ret_t retVal;
+
+ if(pOutput == NULL)
+ return RT_ERR_NULL_POINTER;
+
+ if(pPmask == NULL)
+ return RT_ERR_NULL_POINTER;
+
+ retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_SERIAL_LED_CTRL, RTL8367C_SERIAL_LED_GROUP_NUM_MASK, pOutput);
+ if (retVal != RT_ERR_OK)
+ return retVal;
+
+ retVal = rtl8367c_getAsicRegBits(RTL8367C_REG_SERIAL_LED_CTRL, RTL8367C_SERIAL_LED_PORT_EN_MASK, pPmask);
+ if (retVal != RT_ERR_OK)
+ return retVal;
+
+ return RT_ERR_OK;
+}
+
projects / openwrt / openwrt.git / blobdiff