sunxi: initial 3.14 patchset

[openwrt/openwrt.git] / target / linux / sunxi / patches-3.14 / 232-2-dt-sun7i-add-bluetooth-to-cubietruck.patch

diff --git a/target/linux/sunxi/patches-3.14/232-2-dt-sun7i-add-bluetooth-to-cubietruck.patch b/target/linux/sunxi/patches-3.14/232-2-dt-sun7i-add-bluetooth-to-cubietruck.patch
new file mode 100644 (file)
index 0000000..e41eb82
--- /dev/null
+++ b/target/linux/sunxi/patches-3.14/232-2-dt-sun7i-add-bluetooth-to-cubietruck.patch
@@ -0,0 +1,78 @@
+From 7ed66f828ad1ae46226ad7c1b56466d5ae6d67b9 Mon Sep 17 00:00:00 2001
+From: Chen-Yu Tsai <wens@csie.org>
+Date: Thu, 26 Dec 2013 17:15:47 +0800
+Subject: [PATCH] ARM: dts: sun7i: add bluetooth module to CubieTruck DTS
+
+The CubieTruck has an AMPAK AP6210 WiFi+Bluetooth module. The
+Bluetooth part is a BCM20710 IC connected to UART2 in the A20
+SoC. The IC also takes a 32.768 KHz low power clock input, a power
+enable signal and a wake signal via GPIO.
+
+The Bluetooth module supports out-of-band interrupt signaling via
+GPIO, but this is not supported in this patch.
+---
+ arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 36 ++++++++++++++++++++++++++++++
+ 1 file changed, 36 insertions(+)
+
+diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
+index 2444806..9a127d1 100644
+--- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
++++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts
+@@ -105,6 +105,20 @@
+                               allwinner,drive = <0>;
+                               allwinner,pull = <0>;
+                       };
++
++                      bt_pwr_pin: bt_pwr_pin@0 {
++                              allwinner,pins = "PH18";
++                              allwinner,function = "gpio_out";
++                              allwinner,drive = <0>;
++                              allwinner,pull = <0>;
++                      };
++
++                      bt_wake_pin: bt_wake_pin@0 {
++                              allwinner,pins = "PH24";
++                              allwinner,function = "gpio_out";
++                              allwinner,drive = <0>;
++                              allwinner,pull = <0>;
++                      };
+               };
+ 
+               uart0: serial@01c28000 {
+@@ -113,6 +127,12 @@
+                       status = "okay";
+               };
+ 
++              uart2: serial@01c28800 {
++                      pinctrl-names = "default";
++                      pinctrl-0 = <&uart2_pins_a>;
++                      status = "okay";
++              };
++
+               i2c0: i2c@01c2ac00 {
+                       pinctrl-names = "default";
+                       pinctrl-0 = <&i2c0_pins_a>;
+@@ -194,4 +214,20 @@
+               enable-active-high;
+               gpio = <&pio 7 9 0>;
+       };
++
++      rfkill-switches {
++              compatible = "simple-bus";
++              pinctrl-names = "default";
++
++              rfkill_bt {
++                      compatible = "rfkill-gpio";
++                      pinctrl-0 = <&bt_pwr_pin>, <&clk_out_a_pins_a>;
++                      rfkill-name = "bt";
++                      rfkill-type = <2>;
++                      bt_shutdown-gpios = <0>, <&pio 7 18 0>; /* PH18 */
++                      bt_reset-gpios = <&pio 7 24 0>; /* PH24 */
++                      clocks = <&clk_out_a>;
++                      clock-frequency = <32768>;
++              };
++      };
+ };
+-- 
+2.0.3
+