ar71xx: add support for OCEDO Koala
authorDavid Bauer <mail@david-bauer.net>
Tue, 29 May 2018 15:00:53 +0000 (17:00 +0200)
committerJohn Crispin <john@phrozen.org>
Thu, 7 Jun 2018 07:31:58 +0000 (09:31 +0200)
commite36f8b3f3980903d5cefc51fe274c19c7a0719f2
tree9b3a86a9d695efc09b565dcf88f14dbe28da7253
parenta84962ea35e4e97f1c4a42f2eac0242cc2cbd879
ar71xx: add support for OCEDO Koala

This commit adds support for the OCEDO Koala

SOC: Qualcomm QCA9558 (Scorpion)
RAM:    128MB
FLASH:  16MiB
WLAN1:  QCA9558 2.4 GHz 802.11bgn 3x3
WLAN2:  QCA9880 5 GHz 802.11nac 3x3
INPUT:  RESET button
LED:    Power, LAN, WiFi 2.4, WiFi 5, SYS
Serial: Header Next to Black metal shield
        Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V)
        The Serial setting is 115200-8-N-1.

Tested and working:
 - Ethernet
 - 2.4 GHz WiFi
 - 5 GHz WiFi
 - TFTP boot from ramdisk image
 - Installation via ramdisk image
 - OpenWRT sysupgrade
 - Buttons
 - LEDs

Installation seems to be possible only through booting an OpenWRT
ramdisk image.

Hold down the reset button while powering on the device. It will load a
ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8.

Note: depending on the present software, the device might also try to
pull a file called 'koala-uimage-factory'. Only the name differs, it
is still used as a ramdisk image.

Wait for the ramdisk image to boot. OpenWRT can be written to the flash
via sysupgrade or mtd.

Due to the flip-flop bootloader which we not (yet) support, you need to
set the partition the bootloader is selecting. It is possible from the
initramfs image with

 > fw_setenv bootcmd run bootcmd_1

Afterwards you can reboot the device.

Signed-off-by: David Bauer <mail@david-bauer.net>
14 files changed:
package/boot/uboot-envtools/files/ar71xx
target/linux/ar71xx/base-files/etc/board.d/01_leds
target/linux/ar71xx/base-files/etc/board.d/02_network
target/linux/ar71xx/base-files/etc/diag.sh
target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
target/linux/ar71xx/base-files/lib/ar71xx.sh
target/linux/ar71xx/base-files/lib/upgrade/platform.sh
target/linux/ar71xx/config-4.9
target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
target/linux/ar71xx/files/arch/mips/ath79/Makefile
target/linux/ar71xx/files/arch/mips/ath79/mach-koala.c [new file with mode: 0644]
target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
target/linux/ar71xx/generic/config-default
target/linux/ar71xx/image/generic-senao.mk