--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
-@@ -8,6 +8,8 @@
+@@ -10,6 +10,8 @@
#include <dt-bindings/reset/qcom,gcc-ipq806x.h>
#include <dt-bindings/soc/qcom,gsbi.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
#address-cells = <1>;
-@@ -28,6 +30,16 @@
+@@ -30,6 +32,16 @@
next-level-cache = <&L2>;
qcom,acc = <&acc0>;
qcom,saw = <&saw0>;
};
cpu1: cpu@1 {
-@@ -38,14 +50,350 @@
+@@ -40,11 +52,125 @@
next-level-cache = <&L2>;
qcom,acc = <&acc1>;
qcom,saw = <&saw1>;
};
};
-+ thermal-zones {
-+ tsens_tz_sensor0 {
-+ polling-delay-passive = <0>;
-+ polling-delay = <0>;
-+ thermal-sensors = <&tsens 0>;
-+
-+ trips {
-+ cpu-critical {
-+ temperature = <105000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+
-+ cpu-hot {
-+ temperature = <95000>;
-+ hysteresis = <2000>;
-+ type = "hot";
-+ };
-+ };
-+ };
-+
-+ tsens_tz_sensor1 {
-+ polling-delay-passive = <0>;
-+ polling-delay = <0>;
-+ thermal-sensors = <&tsens 1>;
-+
-+ trips {
-+ cpu-critical {
-+ temperature = <105000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+
-+ cpu-hot {
-+ temperature = <95000>;
-+ hysteresis = <2000>;
-+ type = "hot";
-+ };
-+ };
-+ };
-+
-+ tsens_tz_sensor2 {
-+ polling-delay-passive = <0>;
-+ polling-delay = <0>;
-+ thermal-sensors = <&tsens 2>;
-+
-+ trips {
-+ cpu-critical {
-+ temperature = <105000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+
-+ cpu-hot {
-+ temperature = <95000>;
-+ hysteresis = <2000>;
-+ type = "hot";
-+ };
-+ };
-+ };
-+
-+ tsens_tz_sensor3 {
-+ polling-delay-passive = <0>;
-+ polling-delay = <0>;
-+ thermal-sensors = <&tsens 3>;
-+
-+ trips {
-+ cpu-critical {
-+ temperature = <105000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+
-+ cpu-hot {
-+ temperature = <95000>;
-+ hysteresis = <2000>;
-+ type = "hot";
-+ };
-+ };
-+ };
-+
-+ tsens_tz_sensor4 {
-+ polling-delay-passive = <0>;
-+ polling-delay = <0>;
-+ thermal-sensors = <&tsens 4>;
-+
-+ trips {
-+ cpu-critical {
-+ temperature = <105000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+
-+ cpu-hot {
-+ temperature = <95000>;
-+ hysteresis = <2000>;
-+ type = "hot";
-+ };
-+ };
-+ };
-+
-+ tsens_tz_sensor5 {
-+ polling-delay-passive = <0>;
-+ polling-delay = <0>;
-+ thermal-sensors = <&tsens 5>;
-+
-+ trips {
-+ cpu-critical {
-+ temperature = <105000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+
-+ cpu-hot {
-+ temperature = <95000>;
-+ hysteresis = <2000>;
-+ type = "hot";
-+ };
-+ };
-+ };
-+
-+ tsens_tz_sensor6 {
-+ polling-delay-passive = <0>;
-+ polling-delay = <0>;
-+ thermal-sensors = <&tsens 6>;
-+
-+ trips {
-+ cpu-critical {
-+ temperature = <105000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+
-+ cpu-hot {
-+ temperature = <95000>;
-+ hysteresis = <2000>;
-+ type = "hot";
-+ };
-+ };
-+ };
-+
-+ tsens_tz_sensor7 {
-+ polling-delay-passive = <0>;
-+ polling-delay = <0>;
-+ thermal-sensors = <&tsens 7>;
-+
-+ trips {
-+ cpu-critical {
-+ temperature = <105000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+
-+ cpu-hot {
-+ temperature = <95000>;
-+ hysteresis = <2000>;
-+ type = "hot";
-+ };
-+ };
-+ };
-+
-+ tsens_tz_sensor8 {
-+ polling-delay-passive = <0>;
-+ polling-delay = <0>;
-+ thermal-sensors = <&tsens 8>;
-+
-+ trips {
-+ cpu-critical {
-+ temperature = <105000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+
-+ cpu-hot {
-+ temperature = <95000>;
-+ hysteresis = <2000>;
-+ type = "hot";
-+ };
-+ };
-+ };
-+
-+ tsens_tz_sensor9 {
-+ polling-delay-passive = <0>;
-+ polling-delay = <0>;
-+ thermal-sensors = <&tsens 9>;
-+
-+ trips {
-+ cpu-critical {
-+ temperature = <105000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+
-+ cpu-hot {
-+ temperature = <95000>;
-+ hysteresis = <2000>;
-+ type = "hot";
-+ };
-+ };
-+ };
-+
-+ tsens_tz_sensor10 {
-+ polling-delay-passive = <0>;
-+ polling-delay = <0>;
-+ thermal-sensors = <&tsens 10>;
-+
-+ trips {
-+ cpu-critical {
-+ temperature = <105000>;
-+ hysteresis = <2000>;
-+ type = "critical";
-+ };
-+
-+ cpu-hot {
-+ temperature = <95000>;
-+ hysteresis = <2000>;
-+ type = "hot";
-+ };
-+ };
-+ };
-+ };
-+
- memory {
- device_type = "memory";
- reg = <0x0 0x0>;
-@@ -93,6 +441,15 @@
+@@ -317,6 +443,15 @@
};
};
firmware {
scm {
compatible = "qcom,scm-ipq806x", "qcom,scm";
-@@ -120,6 +477,78 @@
- reg-names = "lpass-lpaif";
- };
-
-+ L2: l2-cache {
-+ compatible = "qcom,krait-cache", "cache";
-+ cache-level = <2>;
-+ qcom,saw = <&saw_l2>;
-+
-+ clocks = <&kraitcc 4>;
-+ clock-names = "l2";
-+ l2-supply = <&smb208_s1a>;
-+ operating-points-v2 = <&opp_table_l2>;
-+ };
-+
-+ rpm: rpm@108000 {
-+ compatible = "qcom,rpm-ipq8064";
-+ reg = <0x108000 0x1000>;
-+ qcom,ipc = <&l2cc 0x8 2>;
-+
-+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
-+ <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
-+ <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
-+ interrupt-names = "ack", "err", "wakeup";
-+
-+ clocks = <&gcc RPM_MSG_RAM_H_CLK>;
-+ clock-names = "ram";
-+
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+
-+ rpmcc: clock-controller {
-+ compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
-+ #clock-cells = <1>;
-+ };
-+
-+ regulators {
-+ compatible = "qcom,rpm-smb208-regulators";
-+
-+ smb208_s1a: s1a {
-+ regulator-min-microvolt = <1050000>;
-+ regulator-max-microvolt = <1150000>;
-+
-+ qcom,switch-mode-frequency = <1200000>;
-+ };
-+
-+ smb208_s1b: s1b {
-+ regulator-min-microvolt = <1050000>;
-+ regulator-max-microvolt = <1150000>;
-+
-+ qcom,switch-mode-frequency = <1200000>;
-+ };
-+
-+ smb208_s2a: s2a {
-+ regulator-min-microvolt = < 800000>;
-+ regulator-max-microvolt = <1250000>;
-+
-+ qcom,switch-mode-frequency = <1200000>;
-+ };
-+
-+ smb208_s2b: s2b {
-+ regulator-min-microvolt = < 800000>;
-+ regulator-max-microvolt = <1250000>;
-+
-+ qcom,switch-mode-frequency = <1200000>;
-+ };
-+ };
-+ };
-+
-+ rng@1a500000 {
-+ compatible = "qcom,prng";
-+ reg = <0x1a500000 0x200>;
-+ clocks = <&gcc PRNG_CLK>;
-+ clock-names = "core";
-+ };
-+
- qcom_pinmux: pinmux@800000 {
- compatible = "qcom,ipq8064-pinctrl";
- reg = <0x800000 0x4000>;
-@@ -160,6 +589,15 @@
+@@ -384,6 +519,15 @@
};
};
spi_pins: spi_pins {
mux {
pins = "gpio18", "gpio19", "gpio21";
-@@ -169,6 +607,53 @@
+@@ -437,6 +581,27 @@
+ bias-bus-hold;
};
};
-
-+ nand_pins: nand_pins {
-+ disable {
-+ pins = "gpio34", "gpio35", "gpio36",
-+ "gpio37", "gpio38";
-+ function = "nand";
-+ drive-strength = <10>;
-+ bias-disable;
-+ };
-+
-+ pullups {
-+ pins = "gpio39";
-+ function = "nand";
-+ drive-strength = <10>;
-+ bias-pull-up;
-+ };
-+
-+ hold {
-+ pins = "gpio40", "gpio41", "gpio42",
-+ "gpio43", "gpio44", "gpio45",
-+ "gpio46", "gpio47";
-+ function = "nand";
-+ drive-strength = <10>;
-+ bias-bus-hold;
-+ };
-+ };
+
+ mdio0_pins: mdio0_pins {
+ mux {
+ bias-disable;
+ };
+ };
-+
- leds_pins: leds_pins {
- mux {
- pins = "gpio7", "gpio8", "gpio9",
-@@ -231,6 +716,17 @@
- clock-output-names = "acpu1_aux";
};
-+ l2cc: clock-controller@2011000 {
-+ compatible = "qcom,kpss-gcc", "syscon";
-+ reg = <0x2011000 0x1000>;
-+ clock-output-names = "acpu_l2_aux";
-+ };
-+
-+ kraitcc: clock-controller {
-+ compatible = "qcom,krait-cc-v1";
-+ #clock-cells = <1>;
-+ };
-+
- saw0: regulator@2089000 {
- compatible = "qcom,saw2", "qcom,apq8064-saw2-v1.1-cpu", "syscon";
- reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
-@@ -243,6 +739,52 @@
+ intc: interrupt-controller@2000000 {
+@@ -513,6 +678,17 @@
regulator;
};
+ compatible = "syscon";
+ reg = <0x12100000 0x10000>;
+ };
-+
-+ gsbi1: gsbi@12440000 {
-+ compatible = "qcom,gsbi-v1.0.0";
-+ cell-index = <1>;
-+ reg = <0x12440000 0x100>;
-+ clocks = <&gcc GSBI1_H_CLK>;
-+ clock-names = "iface";
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ ranges;
-+ status = "disabled";
-+
-+ syscon-tcsr = <&tcsr>;
-+
-+ gsbi1_serial: serial@12450000 {
-+ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-+ reg = <0x12450000 0x100>,
-+ <0x12400000 0x03>;
-+ interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
-+ clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>;
-+ clock-names = "core", "iface";
-+ status = "disabled";
-+ };
-+
-+ gsbi1_i2c: i2c@12460000 {
-+ compatible = "qcom,i2c-qup-v1.1.1";
-+ reg = <0x12460000 0x1000>;
-+ interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
-+ clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
-+ clock-names = "core", "iface";
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ status = "disabled";
-+ };
-+ };
+
gsbi2: gsbi@12480000 {
compatible = "qcom,gsbi-v1.0.0";
cell-index = <2>;
-@@ -368,6 +910,33 @@
+@@ -568,6 +910,33 @@
};
};
gsbi7: gsbi@16600000 {
status = "disabled";
compatible = "qcom,gsbi-v1.0.0";
-@@ -389,6 +958,19 @@
+@@ -589,6 +958,19 @@
clock-names = "core", "iface";
status = "disabled";
};
};
sata_phy: sata-phy@1b400000 {
-@@ -478,6 +1060,95 @@
- #reset-cells = <1>;
+@@ -761,6 +937,17 @@
+ };
};
-+ sfpb_mutex_block: syscon@1200600 {
-+ compatible = "syscon";
-+ reg = <0x01200600 0x100>;
-+ };
-+
-+ hs_phy_0: hs_phy_0 {
-+ compatible = "qcom,ipq806x-usb-phy-hs";
-+ reg = <0x110f8800 0x30>;
-+ clocks = <&gcc USB30_0_UTMI_CLK>;
-+ clock-names = "ref";
-+ #phy-cells = <0>;
-+ };
-+
-+ ss_phy_0: ss_phy_0 {
-+ compatible = "qcom,ipq806x-usb-phy-ss";
-+ reg = <0x110f8830 0x30>;
-+ clocks = <&gcc USB30_0_MASTER_CLK>;
-+ clock-names = "ref";
-+ #phy-cells = <0>;
-+ };
-+
-+ usb3_0: usb3@110f8800 {
-+ compatible = "qcom,dwc3", "syscon";
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ reg = <0x110f8800 0x8000>;
-+ clocks = <&gcc USB30_0_MASTER_CLK>;
-+ clock-names = "core";
-+
-+ ranges;
-+
-+ resets = <&gcc USB30_0_MASTER_RESET>;
-+ reset-names = "master";
-+
-+ status = "disabled";
-+
-+ dwc3_0: dwc3@11000000 {
-+ compatible = "snps,dwc3";
-+ reg = <0x11000000 0xcd00>;
-+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
-+ phys = <&hs_phy_0>, <&ss_phy_0>;
-+ phy-names = "usb2-phy", "usb3-phy";
-+ dr_mode = "host";
-+ snps,dis_u3_susphy_quirk;
-+ };
-+ };
++ L2: l2-cache {
++ compatible = "qcom,krait-cache", "cache";
++ cache-level = <2>;
++ qcom,saw = <&saw_l2>;
+
-+ hs_phy_1: hs_phy_1 {
-+ compatible = "qcom,ipq806x-usb-phy-hs";
-+ reg = <0x100f8800 0x30>;
-+ clocks = <&gcc USB30_1_UTMI_CLK>;
-+ clock-names = "ref";
-+ #phy-cells = <0>;
++ clocks = <&kraitcc 4>;
++ clock-names = "l2";
++ l2-supply = <&smb208_s1a>;
++ operating-points-v2 = <&opp_table_l2>;
+ };
+
-+ ss_phy_1: ss_phy_1 {
-+ compatible = "qcom,ipq806x-usb-phy-ss";
-+ reg = <0x100f8830 0x30>;
-+ clocks = <&gcc USB30_1_MASTER_CLK>;
-+ clock-names = "ref";
-+ #phy-cells = <0>;
+ rpm: rpm@108000 {
+ compatible = "qcom,rpm-ipq8064";
+ reg = <0x108000 0x1000>;
+@@ -828,6 +1015,11 @@
+ clock-output-names = "acpu_l2_aux";
+ };
+
++ kraitcc: clock-controller {
++ compatible = "qcom,krait-cc-v1";
++ #clock-cells = <1>;
+ };
+
-+ usb3_1: usb3@100f8800 {
-+ compatible = "qcom,dwc3", "syscon";
-+ #address-cells = <1>;
-+ #size-cells = <1>;
-+ reg = <0x100f8800 0x8000>;
-+ clocks = <&gcc USB30_1_MASTER_CLK>;
-+ clock-names = "core";
-+
-+ ranges;
-+
-+ resets = <&gcc USB30_1_MASTER_RESET>;
-+ reset-names = "master";
-+
-+ status = "disabled";
-+
-+ dwc3_1: dwc3@10000000 {
-+ compatible = "snps,dwc3";
-+ reg = <0x10000000 0xcd00>;
-+ interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
-+ phys = <&hs_phy_1>, <&ss_phy_1>;
-+ phy-names = "usb2-phy", "usb3-phy";
-+ dr_mode = "host";
-+ snps,dis_u3_susphy_quirk;
-+ };
+ lcc: clock-controller@28000000 {
+ compatible = "qcom,lcc-ipq8064";
+ reg = <0x28000000 0x1000>;
+@@ -835,6 +1027,11 @@
+ #reset-cells = <1>;
+ };
+
++ sfpb_mutex_block: syscon@1200600 {
++ compatible = "syscon";
++ reg = <0x01200600 0x100>;
+ };
+
pcie0: pci@1b500000 {
compatible = "qcom,pcie-ipq8064";
reg = <0x1b500000 0x1000
-@@ -739,6 +1410,59 @@
- status = "disabled";
+@@ -1188,6 +1385,21 @@
+ };
};
-+ adm_dma: dma@18300000 {
-+ compatible = "qcom,adm";
-+ reg = <0x18300000 0x100000>;
-+ interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
-+ #dma-cells = <1>;
-+
-+ clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
-+ clock-names = "core", "iface";
-+
-+ resets = <&gcc ADM0_RESET>,
-+ <&gcc ADM0_PBUS_RESET>,
-+ <&gcc ADM0_C0_RESET>,
-+ <&gcc ADM0_C1_RESET>,
-+ <&gcc ADM0_C2_RESET>;
-+ reset-names = "clk", "pbus", "c0", "c1", "c2";
-+ qcom,ee = <0>;
-+
-+ status = "disabled";
-+ };
-+
-+ nand_controller: nand-controller@1ac00000 {
-+ compatible = "qcom,ipq806x-nand";
-+ reg = <0x1ac00000 0x800>;
-+
-+ clocks = <&gcc EBI2_CLK>,
-+ <&gcc EBI2_AON_CLK>;
-+ clock-names = "core", "aon";
-+
-+ dmas = <&adm_dma 3>;
-+ dma-names = "rxtx";
-+ qcom,cmd-crci = <15>;
-+ qcom,data-crci = <3>;
-+
-+ status = "disabled";
-+
-+ #address-cells = <1>;
-+ #size-cells = <0>;
-+ };
+
+ mdio0: mdio@37000000 {
+ #address-cells = <1>;
vsdcc_fixed: vsdcc-regulator {
compatible = "regulator-fixed";
regulator-name = "SDCC Power";
-@@ -814,4 +1538,17 @@
+@@ -1262,4 +1474,17 @@
};
};
};
projects / openwrt / staging / chunkeey.git / blobdiff