From 8299d1f057439f94c6a4412e2e5c5082b82a30c9 Mon Sep 17 00:00:00 2001 From: =?utf8?q?=C3=81lvaro=20Fern=C3=A1ndez=20Rojas?= Date: Sat, 21 Aug 2021 10:54:34 +0200 Subject: [PATCH] bcm27xx: add kernel 5.10 support MIME-Version: 1.0 Content-Type: text/plain; charset=utf8 Content-Transfer-Encoding: 8bit Rebased RPi foundation patches on linux 5.10.59, removed applied and reverted patches, wireless patches and defconfig patches. bcm2708: boot tested on RPi B+ v1.2 bcm2709: boot tested on RPi 4B v1.1 4G bcm2711: boot tested on RPi 4B v1.1 4G Signed-off-by: Álvaro Fernández Rojas --- target/linux/bcm27xx/bcm2708/config-5.10 | 366 + target/linux/bcm27xx/bcm2709/config-5.10 | 464 + target/linux/bcm27xx/bcm2710/config-5.10 | 448 + target/linux/bcm27xx/bcm2711/config-5.10 | 463 + target/linux/bcm27xx/modules/sound.mk | 20 + target/linux/bcm27xx/modules/video.mk | 8 +- ...vert-702b94bff3c50542a6e4ab9a4f4cef0.patch | 99 + ...23-properly-handle-oscillator-stop-b.patch | 56 + ...ing-bcm2835-audio-Drop-DT-dependency.patch | 96 + ...v-Fix-CS-polarity-if-GPIO-descriptor.patch | 32 + ...lbox-avoid-timer-start-from-callback.patch | 58 + ...smsx95xx-fix-crimes-against-truesize.patch | 47 + ...ental-Enable-turbo_mode-and-packetsi.patch | 43 + ...ow-mac-address-to-be-set-in-smsc95xx.patch | 96 + ...e_resource-against-resources-without.patch | 28 + ...cm2836-Avoid-Invalid-trigger-warning.patch | 24 + ...0011-irqchip-bcm2835-Add-FIQ-support.patch | 127 + ...hip-irq-bcm2835-Add-2836-FIQ-support.patch | 99 + ...ompletely-disable-the-spidev-warning.patch | 24 + ...5-Load-driver-early-and-support-lega.patch | 101 + ...0015-firmware-Updated-mailbox-header.patch | 27 + ...rtc-Add-SPI-alias-for-pcf2123-driver.patch | 20 + ...835-Support-setting-reboot-partition.patch | 102 + ...-off-rather-than-busy-spinning-when-.patch | 23 + ...-Make-RASPBERRYPI_POWER-depend-on-PM.patch | 19 + ...cks-early-during-the-boot-process-so.patch | 45 + ...void-initialising-if-already-enabled.patch | 25 + ...Mark-used-PLLs-and-dividers-CRITICAL.patch | 28 + ...lk-bcm2835-Add-claim-clocks-property.patch | 120 + ...35-Read-max-core-clock-from-firmware.patch | 115 + ...Demote-deferral-errors-to-INFO-level.patch | 35 + .../950-0026-Update-vfpmodule.c.patch | 137 + ...0-0027-i2c-bcm2835-Add-debug-support.patch | 189 + ...-0028-mm-Remove-the-PFN-busy-warning.patch | 25 + ...bcm2836-Remove-regmap-and-syscon-use.patch | 112 + ...8xx-Enable-LEDs-and-auto-negotiation.patch | 48 + ...1-Don-t-use-DT-aliases-for-numbering.patch | 29 + ...0032-amba_pl011-Round-input-clock-up.patch | 86 + ...-Insert-mb-for-correct-FIFO-handling.patch | 27 + ...Add-cts-event-workaround-DT-property.patch | 50 + ...011-Make-TX-optimisation-conditional.patch | 85 + ...y-amba-pl011-Add-un-throttle-support.patch | 61 + ...011-Avoid-rare-write-when-full-error.patch | 42 + ...Set-base-to-0-give-expected-gpio-num.patch | 22 + ...0039-Main-bcm2708-bcm2709-linux-port.patch | 150 + .../950-0040-Add-dwc_otg-driver.patch | 61618 ++++++++++++++++ .../950-0041-bcm2708-framebuffer-driver.patch | 3559 + ...lti-frame-buffer-support-from-the-Pi.patch | 828 + ...50-0043-fbdev-add-FBIOCOPYAREA-ioctl.patch | 337 + ...nsole-framebuffer-imageblit-function.patch | 209 + ...45-dmaengine-Add-support-for-BCM2708.patch | 640 + ...046-MMC-added-alternative-MMC-driver.patch | 1933 + ...dhost-driver-and-an-overlay-to-enabl.patch | 2481 + ...m-driver-for-querying-firmware-memor.patch | 488 + ...device-for-rootless-user-GPIO-access.patch | 299 + .../950-0050-Add-SMI-driver.patch | 1910 + ...950-0051-Add-Chris-Boot-s-i2c-driver.patch | 660 + ...0-0052-char-broadcom-Add-vcio-module.patch | 254 + ...irmware-bcm2835-Support-ARCH_BCM270x.patch | 83 + ...BCM2708-Add-core-Device-Tree-support.patch | 26485 +++++++ ...wr_led-and-the-required-input-trigge.patch | 169 + ...dded-Device-IDs-for-August-DVB-T-205.patch | 22 + ...o_user-and-__copy_from_user-performa.patch | 1586 + ...off-Allow-it-to-work-on-Raspberry-Pi.patch | 35 + ...d-Raspberry-Pi-Sense-HAT-core-driver.patch | 852 + ...all-the-downstream-rpi-sound-card-dr.patch | 15106 ++++ ...when-module-probes-before-i2c-module.patch | 46 + ...lay-add-backlight-driver-and-overlay.patch | 172 + ...bcm2835-virtgpio-Virtual-GPIO-driver.patch | 256 + ...064-OF-DT-Overlay-configfs-interface.patch | 427 + ...i_h5-Don-t-send-conf_req-when-ACTIVE.patch | 23 + ...und-Robin-dispatch-IRQs-between-CPUs.patch | 72 + ...ware-emulation-of-deprecated-instruc.patch | 28 + ...68-cache-export-clean-and-invalidate.patch | 53 + ...-AXI-performance-monitor-driver-2222.patch | 691 + ...m2835-Set-Serial-number-and-Revision.patch | 63 + ...Q-Fix-bad-mode-in-data-abort-handler.patch | 116 + ...FIQs-to-avoid-__irq_startup-warnings.patch | 36 + ...ware-Export-the-general-transaction-.patch | 32 + ...so-set-bus-numbers-from-reg-property.patch | 35 + ...ear-option-to-pps-gpio-via-dtoverlay.patch | 21 + ...78xx-Read-initial-EEE-status-from-DT.patch | 40 + ...fault-mouse-polling-interval-to-60Hz.patch | 32 + ...to-export-gpio-used-by-gpio-poweroff.patch | 57 + ...pberrypi-Notify-firmware-of-a-reboot.patch | 84 + ...bcm2835-Calc.-FIQ_START-at-boot-time.patch | 66 + ...fs-Use-of_overlay_fdt_apply-API-call.patch | 114 + ...Disable-TCP-Segmentation-Offload-TSO.patch | 56 + ...e-enabling-of-EEE-into-PHY-init-code.patch | 64 + .../950-0084-Add-rpi-poe-fan-driver.patch | 581 + ...SPI_DRV-should-select-DVB_CXD2880-wi.patch | 20 + ...i-Prevent-voltage-low-warnings-from-.patch | 75 + ...rypi-Add-backward-compatible-get_thr.patch | 79 + ...is7xx-Don-t-spin-if-no-data-received.patch | 23 + ...step_wise-add-support-for-hysteresis.patch | 94 + ...step_wise-avoid-throttling-at-hyster.patch | 22 + ...950-0091-Update-issue-templates-2736.patch | 47 + ...xx-Support-auto-downshift-to-100Mb-s.patch | 91 + ...rypi-Report-the-fw-variant-during-pr.patch | 101 + ...e-link-events-to-minimize-poll-storm.patch | 45 + ...xx-EEE-support-is-now-a-PHY-property.patch | 26 + ...ma-Add-support-for-per-channel-flags.patch | 48 + ...8-Add-backup-switchover-mode-support.patch | 50 + ...use-default-alignment-for-rx-buffers.patch | 23 + ...ov5647-Add-set_fmt-and-get_fmt-calls.patch | 47 + ...dia-ov5647-Add-support-for-PWDN-GPIO.patch | 92 + ...-support-for-non-continuous-clock-mo.patch | 79 + ...-tc358743-Increase-FIFO-level-to-374.patch | 31 + ...ix-connected-active-CSI-2-lane-repor.patch | 74 + ...-Add-support-for-972Mbit-s-link-freq.patch | 79 + ...743-Check-I2C-succeeded-during-probe.patch | 98 + ...180-Default-to-the-first-valid-input.patch | 45 + ...v7180-Add-YPrPb-support-for-ADV7282M.patch | 24 + ...Add-helper-defines-for-printing-FOUR.patch | 28 + ...-Document-BCM283x-CSI2-CCP2-receiver.patch | 103 + ...-Add-entry-for-BCM2835-Unicam-driver.patch | 28 + ...eturn-an-appropriate-colorspace-from.patch | 98 + ...chiq-Avoid-use-of-bool-in-structures.patch | 24 + ...chiq-Add-support-for-event-callbacks.patch | 356 + ...vices-Support-sending-data-to-MMAL-p.patch | 42 + ...2-Allow-exporting-of-a-struct-dmabuf.patch | 83 + ...iq-Fix-client_component-for-64-bit-k.patch | 35 + ...-bcm2835-Use-zd-when-printing-size_t.patch | 24 + ...-ov5647-Use-gpiod_set_value_cansleep.patch | 54 + ...iq-Add-in-the-Bayer-encoding-formats.patch | 51 + ...iq-Update-mmal_parameters.h-with-rec.patch | 56 + ...iq-Free-the-event-context-for-contro.patch | 28 + ...-vchiq-Fix-memory-leak-in-error-path.patch | 76 + ...ake-GPIO-an-output-for-strong-pullup.patch | 27 + ...24-arm-bcm2835-Fix-FIQ-early-ioremap.patch | 73 + ...arm-bcm2835-DMA-can-only-address-1GB.patch | 25 + ...rng-iproc-rng200-Add-BCM2838-support.patch | 153 + ...i-iproc-Fix-vmmc-regulators-on-iProc.patch | 46 + ...128-vchiq-Add-36-bit-address-support.patch | 202 + ...835-pcm.c-Support-multichannel-audio.patch | 46 + ...genet-constrain-max-DMA-burst-length.patch | 20 + ...Better-coalescing-parameter-defaults.patch | 43 + ...-link-energy-detect-powerdown-for-ex.patch | 31 + ...2835-enable-shared-interrupt-support.patch | 35 + ...clk-bcm2835-Don-t-wait-for-pllh-lock.patch | 38 + ...-bcm-bcm2835-pm-Add-support-for-2711.patch | 102 + ...support-for-setting-leaf-clock-rates.patch | 53 + ...w-reparenting-leaf-clocks-while-they.patch | 71 + ...-for-updating-interrupt-endpoint-int.patch | 104 + ...hci_fixup_endpoint-for-interval-adju.patch | 129 + ...fixup_endpoint-after-mangling-interv.patch | 23 + ...cm2835-Add-bcm2838-compatible-string.patch | 20 + ...50-0142-drm-v3d-Add-support-for-2711.patch | 20 + ...-flush-if-the-device-is-currently-of.patch | 52 + ...4-drm-v3d-Hook-up-the-runtime-PM-ops.patch | 34 + ...or-host-controllers-that-don-t-updat.patch | 90 + ...35-Set-clock-stretch-timeout-to-35ms.patch | 47 + ...bcm2835-Avoid-null-pointer-exception.patch | 29 + ...-drm-v3d-HACK-gut-runtime-pm-for-now.patch | 109 + ...m-v3d-Clock-V3D-down-when-not-in-use.patch | 161 + ...-chardev-for-mmap-ing-the-RPiVid-con.patch | 441 + ...ce-quirks-for-Freeway-Airmouse-T3-an.patch | 63 + ...152-Add-HDMI1-facility-to-the-driver.patch | 85 + ...t-Workaround-2-for-Pi4-Ethernet-fail.patch | 51 + ...ore-event-ring-segment-table-entries.patch | 60 + ...155-configs-arm64-bcm2711-Enable-V3D.patch | 28 + ...arch-arm-Add-model-string-to-cpuinfo.patch | 36 + ...Add-Revision-Serial-Model-to-cpuinfo.patch | 58 + ...s-Add-binding-for-the-Sony-IMX219-se.patch | 77 + ...0-0159-v4l2-Add-a-Greyworld-AWB-mode.patch | 34 + ...cm2835-camera-Add-greyworld-AWB-mode.patch | 37 + ...61-drm-v3d-Delete-pm_runtime-support.patch | 62 + ....dtbo-overlays-to-be-built-piecemeal.patch | 36 + ...oard-clk-and-pinctrl-to-bcm2711-comp.patch | 26 + ...-device-names-check-for-enable-state.patch | 139 + ...binding-for-the-Infineon-IRS1125-sen.patch | 66 + ...driver-for-the-Infineon-IRS1125-dept.patch | 1231 + ...-clear-MMU-control-bits-on-exception.patch | 34 + ...Suppress-all-but-the-first-MMU-error.patch | 39 + ...950-0169-drm-v3d-Plug-dma_fence-leak.patch | 28 + ...m-Register-vcsm-cma-as-a-platform-dr.patch | 40 + ...m-Register-bcm2835-codec-as-a-platfo.patch | 40 + ...-bcmgenet-The-second-IRQ-is-optional.patch | 24 + ...ow-ethernet-LED-mode-to-be-set-via-d.patch | 46 + ...nge-the-default-ethernet-LED-actions.patch | 33 + ...Handle-missing-clock-more-gracefully.patch | 27 + ...-clock-so-firmware-knows-we-are-usin.patch | 27 + ...Allow-cpufreq-driver-to-also-adjust-.patch | 25 + ...0-0178-clk-bcm2835-Disable-v3d-clock.patch | 58 + ...ma_mask-as-well-as-coherent_dma_mask.patch | 27 + ...m-Set-up-dma-ranges-on-child-devices.patch | 33 + ...e-the-old-dma-controller-for-OF-conf.patch | 51 + ...ckport-BCM2711-support-from-upstream.patch | 47 + ...lise-rpi-firmware-before-clk-bcm2835.patch | 47 + ...hiq_arm-Give-vchiq-children-DT-nodes.patch | 39 + ...trl-bcm2835-Remove-gpiochip-on-error.patch | 25 + ...2835-Change-init-order-for-gpio-hogs.patch | 78 + ...2835-Accept-fewer-than-expected-IRQs.patch | 31 + ...s-char-vcio-Use-common-compat-header.patch | 23 + ...-bcm2708_fb-Use-common-compat-header.patch | 23 + ...f-overlay-Correct-symbol-path-fixups.patch | 37 + ...-Add-DT-docs-for-Brcmstb-PCIe-device.patch | 77 + ...ow-.dtbo-overlays-to-be-built-adjust.patch | 26 + ...t-Disable-skip_umac_reset-by-default.patch | 23 + ...cc-Add-packed-10bit-YUV-4-2-0-format.patch | 55 + ...uapi-hevc-Add-scaling-matrix-control.patch | 150 + ...-uapi-hevc-Add-segment-address-field.patch | 61 + ...uapi-Add-hevc-ctrls-for-WPP-decoding.patch | 40 + ...h-Add-a-format-for-column-YUV4-2-0-m.patch | 302 + ...s-media-Add-binding-for-the-Raspberr.patch | 106 + ...a-Add-Raspberry-Pi-V4L2-H265-decoder.patch | 4341 ++ ...-0201-mmc-sdhci-Silence-MMC-warnings.patch | 42 + ...k-Add-a-binding-for-the-RPi-Firmware.patch | 63 + ...lay-vc4-hdmi-Add-BCM2711-HDMI-contro.patch | 174 + ...the-pitch-is-only-valid-for-linear-f.patch | 39 + ...verlays-Fix-dtc-warnings-in-i2c-gpio.patch | 24 + ...ar-rpivid-Remove-legacy-name-support.patch | 53 + ...CS_HIGH-if-GPIO-descriptors-are-used.patch | 57 + ...ar-rpivid-Don-t-map-more-than-wanted.patch | 51 + ...icam-Driver-for-CCP2-CSI2-camera-int.patch | 2709 + ...core-Add-sensor-ancillary-data-V4L2-.patch | 85 + ...EDIA_BUS_FMT_SENSOR_DATA-media-bus-f.patch | 64 + ...icam-Add-support-for-mulitple-device.patch | 1084 + ...cm2835-unicam-Add-embedded-data-node.patch | 1170 + ...icam-Use-dummy-buffer-if-none-have-b.patch | 308 + ...icam-Disable-event-related-ioctls-on.patch | 31 + ...icam-Add-support-for-the-FRAME_SYNC-.patch | 55 + ...ertise-embedded-data-node-on-media-p.patch | 336 + ...icam-Re-fetch-mbus-code-from-subdev-.patch | 49 + ...core-Add-ISP-statistics-output-V4L2-.patch | 94 + ...trls-Add-CID-base-for-the-bcm2835-is.patch | 169 + ...q-Load-bcm2835_isp-driver-from-vchiq.patch | 39 + ...35-dma-Add-proper-40-bit-DMA-support.patch | 801 + ...Make-the-i2c-gpio-overlay-safe-again.patch | 32 + ...-Declare-that-the-driver-can-create-.patch | 27 + ...-return-codes-from-ov5647_write-ov56.patch | 74 + ...-basic-support-for-multiple-sensor-m.patch | 407 + ...-V4L2-controls-for-analogue-gain-exp.patch | 277 + ...ov5647-Add-extra-10-bit-sensor-modes.patch | 549 + ...nge-defaults-to-better-match-raw-cam.patch | 59 + ...-Add-support-for-g_selection-to-refl.patch | 206 + ...67-Fixup-error-path-to-release-mutex.patch | 29 + ...c-ov5647-Support-V4L2_CID_PIXEL_RATE.patch | 131 + ...7-Set-V4L2_SUBDEV_FL_HAS_EVENTS-flag.patch | 143 + ...5647-Add-support-for-V4L2_CID_VBLANK.patch | 205 + ...-Neither-analogue-gain-nor-exposure-.patch | 58 + ...5647-Use-member-names-in-mode-tables.patch | 111 + ...-Advertise-the-correct-exposure-rang.patch | 119 + ...icam-Add-support-for-VIDIOC_-S-G-_SE.patch | 82 + ...icam-Do-not-stop-streaming-in-unicam.patch | 28 + ...icam-Fix-reference-counting-in-unica.patch | 38 + ...i2c-tc358743-Fix-fallthrough-warning.patch | 20 + ...835-unicam-Fix-uninitialized-warning.patch | 21 + ...8_fb-Disable-FB-if-no-displays-found.patch | 34 + ...a-i2c-Add-IMX477-CMOS-sensor-binding.patch | 130 + ...835-unicam-Always-service-interrupts.patch | 51 + ...6is7xx-Fix-for-hardware-flow-control.patch | 70 + ...vices-mmal-vchiq-Update-parameters-l.patch | 28 + ...vices-bcm2835-camera-Request-headers.patch | 30 + .../950-0249-kbuild-Disable-gcc-plugins.patch | 28 + ...icam-Retain-packing-information-on-G.patch | 48 + ...251-zswap-Defer-zswap-initialisation.patch | 125 + ...cm2835-Set-base-for-bcm2711-GPIO-to-.patch | 27 + ...chiq_arm-Clean-up-40-bit-DMA-support.patch | 174 + ...icam-change-minimum-number-of-vb2_qu.patch | 28 + ...ble-HDMI-audio-when-vc4-is-used-3640.patch | 33 + ...-t-prevent-IRQ-usage-of-output-GPIOs.patch | 50 + ...mstb-Add-DT-property-to-control-L1SS.patch | 79 + ...125-Using-i2c_transfer-for-ic2-reads.patch | 65 + ...s1125-Refactoring-and-debug-messages.patch | 123 + ...omic-access-to-imager-reconfiguratio.patch | 381 + ...5-Keep-HW-in-sync-after-imager-reset.patch | 181 + ...m2835-audio-Add-missing-MODULE_ALIAS.patch | 30 + ...move-the-downstream-version-of-bcm28.patch | 3175 + ...icam-Driver-for-CCP2-CSI2-camera-int.patch | 3150 + ...icam-Add-support-for-get_mbus_config.patch | 56 + ...icam-Avoid-gcc-warning-over-0-on-end.patch | 27 + ...-set-the-format-before-VIDIOC_SUBDEV.patch | 40 + ...mx290-Add-support-for-74.25MHz-clock.patch | 264 + ...-Correct-range-for-V4L2_CID_GAIN-to-.patch | 26 + ...-Convert-HMAX-setting-into-V4L2_CID_.patch | 159 + ...x290-Add-support-for-V4L2_CID_VBLANK.patch | 141 + ...0-Add-exposure-control-to-the-driver.patch | 93 + ...i2c-imx290-Add-H-and-V-flip-controls.patch | 83 + ...s-media-i2c-Add-mono-version-to-IMX2.patch | 36 + ...-Add-support-for-the-mono-sensor-var.patch | 185 + ...-Switch-set_hmax-to-use-imx290_write.patch | 43 + ...50-bcm2835aux-defer-if-clock-is-zero.patch | 28 + ...l-format-for-MIPI-packed-12bit-luma-.patch | 95 + ...l-format-for-MIPI-packed-14bit-luma-.patch | 104 + ...icam-Add-support-for-12bit-mono-pack.patch | 25 + ...icam-Add-support-for-14bit-mono-sour.patch | 29 + ...icam-Add-support-for-unpacked-14bit-.patch | 42 + ...83-bcm2835-dma-Add-NO_WAIT_RESP-flag.patch | 54 + ...950-0284-media-i2c-add-ov9281-driver.patch | 1218 + ...-fix-mclk-issue-when-probe-multiple-.patch | 60 + ...-add-enum_frame_interval-function-fo.patch | 97 + ...-Fixup-for-recent-kernel-releases-an.patch | 681 + ...-i2c-ov9281-Read-chip-ID-via-2-reads.patch | 42 + ...-Explicitly-set-v-h-blank-on-mode-ch.patch | 46 + ...-Add-support-for-g_selection-to-repo.patch | 156 + ...-Set-the-colorspace-fields-in-the-fo.patch | 31 + ...icam-Reinstate-V4L2_CAP_READWRITE-in.patch | 28 + ...icam-Ensure-type-is-VIDEO_CAPTURE-in.patch | 36 + ...icam-Set-VPU-min-clock-freq-to-250Mh.patch | 127 + ...835-unicam-Update-documentation-with.patch | 38 + ...ov5647-Parse-and-register-properties.patch | 49 + ...950-0297-leds-Add-the-actpwr-trigger.patch | 235 + ...chiq_arm-children-inherit-DMA-config.patch | 36 + ...835-dma-Advertise-the-full-DMA-range.patch | 77 + ...v7-Force-misalignment-of-early-stmia.patch | 60 + ...icam-Select-MEDIA_CONTROLLER-and-VID.patch | 27 + ...ivid-Select-MEDIA_CONTROLLER-and-MED.patch | 32 + ...icam-Drop-WARN-on-uing-direct-cache-.patch | 34 + ...43-Only-allow-supported-pixel-fmts-i.patch | 30 + ...ov9281-Add-support-for-8-bit-readout.patch | 188 + ...835-mmc-uninitialized_var-is-no-more.patch | 20 + ...elist_table-is-now-productlist_table.patch | 20 + ...mplement-a-DMA-pool-for-small-bulk-t.patch | 122 + ...-Add-enum-for-RPI_FIRMWARE_FRAMEBUFF.patch | 23 + ...cec_available-flag-as-always-support.patch | 44 + ...e-dma-configuration-from-the-HVS-or-.patch | 54 + ...D_CTL_WHOLSMP-and-HD_CTL_CHALIGN_SET.patch | 42 + .../950-0313-vc4_hdmi-Set-HDMI_MAI_FMT.patch | 124 + ...-vc4-add-iec958-controls-to-vc4_hdmi.patch | 119 + ...move-setup-from-hw_params-to-prepare.patch | 58 + ...enable-HBR-MAI-format-on-HBR-streams.patch | 25 + ...firmware-logic-for-MAI-threshold-set.patch | 47 + ...t-VC4_HDMI_MAI_CONFIG_FORMAT_REVERSE.patch | 24 + ...ort-for-DRM_FORMAT_P030-to-vc4-plane.patch | 163 + ...ort-for-YUV-color-encodings-and-rang.patch | 139 + ...0-0321-drm-vc4-Add-firmware-kms-mode.patch | 2364 + ...-as-an-acceptable-node-for-dma-range.patch | 27 + ...2c-Add-driver-for-Sony-IMX477-sensor.patch | 2266 + ...-Add-support-for-adaptive-frame-cont.patch | 182 + ...-Return-correct-result-on-sensor-id-.patch | 25 + ...imx477-Parse-and-register-properties.patch | 45 + ...835-unicam-Always-service-interrupts.patch | 51 + ...835-unicam-Fix-uninitialized-warning.patch | 21 + ...icam-Fixup-review-comments-from-Hans.patch | 244 + ...icam-Retain-packing-information-on-G.patch | 48 + ...icam-change-minimum-number-of-vb2_qu.patch | 28 + ...tft-Add-support-for-display-variants.patch | 205 + ...33-rpivid_h265-Fix-width-height-typo.patch | 21 + ...et-bcmgenet-Reset-RBUF-on-first-open.patch | 70 + ...com-char-drivers-back-to-build-files.patch | 30 + ...se-sched_frame-for-periodic-QHs-that.patch | 33 + ...camera-Replace-deprecated-V4L2_PIX_F.patch | 30 + ...04_services-Add-new-vc-sm-cma-driver.patch | 2926 + ...hiq-mmal-Add-support-for-14bit-Bayer.patch | 27 + ...l-vchiq-Add-monochrome-image-formats.patch | 29 + ...iq-Use-vc-sm-cma-to-support-zero-cop.patch | 162 + ...services-Add-a-V4L2-M2M-codec-driver.patch | 3070 + ...-reserve-channel-0-if-legacy-dma-dri.patch | 32 + ...isp-Add-bcm2835-isp-uapi-header-file.patch | 338 + ...vices-ISP-Add-a-more-complex-ISP-pro.patch | 2406 + ...resent-but-empty-dmas-disables-audio.patch | 33 + ...gfs-node-that-dumps-the-current-disp.patch | 70 + .../950-0348-gpio-Add-gpio-fsm-driver.patch | 1182 + ...the-HDMI-registers-into-the-debugfs-.patch | 97 + ...-dts-bcm271x-Use-a53-pmu-drop-RPI364.patch | 67 + ...ion-to-disable-composite-to-vc4-kms-.patch | 36 + ...Correct-link-frequency-to-match-the-.patch | 25 + ...0-0353-dts-Add-CM4-to-arm64-dt-files.patch | 28 + ...-the-2711-HVS-as-a-suitable-DMA-node.patch | 24 + ...-quirks-add-link-TRB-quirk-for-VL805.patch | 61 + ...dy-the-Raspberry-Pi-Makefile-entries.patch | 43 + ...35-audio-Add-disable-headphones-flag.patch | 34 + ...isable-headphone-audio-on-Zeroes-CM4.patch | 42 + ...s-Enable-headphone-audio-in-audremap.patch | 26 + ...pseudo_pallete-to-prevent-crash-on-f.patch | 30 + ...ARM-dts-Expand-PCIe-space-on-BCM2711.patch | 30 + ...nimise-header-and-fix-build-warnings.patch | 887 + ...50-0363-gpio-fsm-Fix-a-build-warning.patch | 22 + ...-0364-rpivid_h625-Fix-build-warnings.patch | 68 + ...-0365-bcm2708_fb-Fix-a-build-warning.patch | 22 + .../950-0366-PiFi-40-Devicetree-files.patch | 91 + ...-PiFi-40-driver-Makefile-and-Kconfig.patch | 332 + ...35-pcm-Fix-up-multichannel-pcm-audio.patch | 55 + ...-Ignore-params-after-the-partition-n.patch | 29 + ...rypi-Add-support-for-tryonce-reboot-.patch | 72 + ...it-out-the-BCM54213PE-from-the-BCM54.patch | 71 + ...roadcom-Add-bcm54213pe-configuration.patch | 34 + ...MAX31856-support-to-maxtherm-overlay.patch | 102 + ...0374-ARM-dts-Add-bcm2711-rpi-400.dts.patch | 657 + ...ecate-and-delete-the-sdtweak-overlay.patch | 112 + ...7xx-Remove-enable_headphones-setting.patch | 110 + ...dmi-Report-that-3d-stereo-is-allowed.patch | 20 + ...tb-Restore-initial-fundamental-reset.patch | 35 + ...nused-infoframe-packet-RAM-registers.patch | 45 + ...-Poll-the-device-if-no-interrupt-is-.patch | 98 + ...n-overlay-for-the-EDT-FT5406-touchsc.patch | 96 + ...rrypi-touchscreen-Use-independent-I2.patch | 58 + ...rrypi-ts-Insert-delay-before-polling.patch | 26 + ...upport-for-RaspberryPi-7-panel-over-.patch | 100 + .../950-0385-mcp251xfd-add-overlay.patch | 283 + ...v9281-Add-1280x720-and-640x480-modes.patch | 209 + ...ings-Add-compatible-for-BCM2711-DSI1.patch | 23 + ...e-compatible-string-for-BCM2711-DSI1.patch | 23 + ...-vc4-Correct-DSI-register-definition.patch | 34 + .../950-0390-Allo-boss2-driver.patch | 1185 + .../950-0391-Add-allo-boss2-overlay.patch | 98 + ...llo-Piano-Plus-dac-driver-for-5.4.y-.patch | 30 + ...icam-Correctly-handle-error-propagat.patch | 27 + ...icam-Return-early-from-stop_streamin.patch | 64 + ...icam-Clear-clock-state-when-stopping.patch | 25 + ...-PCI-brcmstb-Advertise-MSI-X-support.patch | 27 + ...dts-CM4-audio-pins-are-not-connected.patch | 21 + ...dd-PCF85063-and-PCF85063A-to-i2c-rtc.patch | 339 + ...ys-Fix-cut-and-paste-error-in-README.patch | 24 + ...codec-Ensure-OUTPUT-timestamps-are-a.patch | 53 + ...-Ack-pending-PHY-ints-when-resetting.patch | 32 + ...-overlays-mpu6050-Add-addr-parameter.patch | 36 + ...malize_zpos-conditional-on-using-fkm.patch | 29 + ...missing-addresses-to-ads1015-ads1115.patch | 41 + ...2c-imx477-Selection-compliance-fixes.patch | 80 + ...vices-codec-Add-support-for-CID-MPEG.patch | 64 + ...vices-codec-Clear-last-buf-dequeued-.patch | 37 + ...the-full-state-to-CRTC-atomic-enable.patch | 1183 + ...-the-full-state-to-CRTC-atomic_check.patch | 1027 + ...the-full-state-to-CRTC-atomic-begin-.patch | 1018 + ...n-the-HVS-atomic-hooks-to-the-new-AP.patch | 109 + ...ss-the-atomic-state-to-encoder-hooks.patch | 161 + ...-t-access-the-connector-state-in-res.patch | 35 + ...hdmi-Create-a-custom-connector-state.patch | 88 + ...re-pixel-frequency-in-the-connector-.patch | 97 + ...-the-connector-state-pixel-rate-for-.patch | 102 + ...drm-vc4-hdmi-Enable-10-12-bpc-output.patch | 203 + ...18-drm-vc4-Fixup-fkms-for-API-change.patch | 50 + ...Rebuild-upstream-with-latest-ovmerge.patch | 291 + ...for-Seeed-Studio-CAN-BUS-FD-HAT-4034.patch | 217 + ...-0421-vc-sm-cma-fixed-kbuild-problem.patch | 30 + ...vices-codec-Fix-logical-precedence-i.patch | 36 + ...vices-Add-additional-unpacked-raw-fo.patch | 51 + ...codec-Add-the-unpacked-16bpp-raw-for.patch | 167 + ...codec-Log-the-number-of-excess-suppo.patch | 43 + ...isp-Add-the-unpacked-16bpp-raw-forma.patch | 174 + ...isp-Log-the-number-of-excess-support.patch | 29 + ...bcm2835-dma-Add-DMA_WIDE_SOURCE-and-.patch | 64 + ...ma-Move-WAIT_RESP-from-extra-to-info.patch | 25 + ...void-losing-CS-flags-after-interrupt.patch | 21 + ...DE_SOURCE-and-DMA_WIDE_DEST-for-hdmi.patch | 43 + ...-Bump-hdmi-audio-dma-panic-priority-.patch | 33 + ...2c-ov5647-Selection-compliance-fixes.patch | 88 + ...eed-Studio-CAN-BUS-FD-HAT-a-v2-postf.patch | 286 + ...rlay-for-Seeed-Studio-CAN-BUS-FD-HAT.patch | 192 + ...verlays-add-wm8960-soundcard-overlay.patch | 129 + ...dd-spi-override-to-merus-amp-overlay.patch | 44 + ...regulator-node-to-all-downstream-Pi-.patch | 328 + ...e-sensor-overlays-to-use-cam1_reg-wh.patch | 243 + ...an-fd-hat-clarify-how-to-identify-HA.patch | 45 + ...erlays-Make-the-i2c-gpio-overlay-saf.patch | 26 + ...verlays-Fix-dtc-warnings-in-i2c-gpio.patch | 28 + ...isp-Add-colour-denoise-configuration.patch | 56 + ...vices-ISP-Add-colour-denoise-control.patch | 75 + ...s-nvmem-Add-bindings-for-rmem-driver.patch | 75 + ...r-to-expose-reserved-memory-as-nvmem.patch | 163 + ...Add-reserved-memory-template-to-hold.patch | 60 + ...around-fix-for-zero-length-transfers.patch | 50 + ...nce-unavoidable-dtc-overlay-warnings.patch | 31 + ...overlays-to-support-Hifiberry-AMP100.patch | 132 + ...iberry-DAC-driver-for-Hifiberry-AMP1.patch | 238 + ...are-Pi400-and-CM4-have-no-audio-pins.patch | 41 + ...-Replace-V4L2_CID_GAIN-with-V4L2_CID.patch | 38 + ...-Fix-number-of-controls-in-v4l2_ctrl.patch | 28 + ...cm-Select-BRCMSTB_L2_IRQ-for-bcm2835.patch | 37 + ...ate-the-CEC-clock-divider-on-HSM-rat.patch | 31 + ...7-drm-vc4-hdmi-Introduce-a-CEC-clock.patch | 60 + ...c4-hdmi-Split-the-interrupt-handlers.patch | 141 + ...-Support-BCM2711-CEC-interrupt-setup.patch | 116 + ...-t-register-the-CEC-adapter-if-there.patch | 37 + ...ay-bcm2711-hdmi-Add-CEC-and-hotplug-.patch | 51 + ...711-Add-the-CEC-interrupt-controller.patch | 58 + ...bsc_intr-and-aon_intr-by-default-and.patch | 38 + ...464-bcm2711-Remove-old-GIC-interrupt.patch | 30 + ...camera-Fix-the-cherry-pick-of-AWB-Gr.patch | 28 + .../950-0466-Overlays-for-PiFi-Mini-amp.patch | 83 + ...-PiFi-Mini-to-rpi-simple-soundcard.c.patch | 144 + ...w-formats-with-different-colour-spac.patch | 712 + ...C-Pro-fix-for-the-PLL-when-changing-.patch | 56 + ...picture-line-bug-in-all-ov9281-modes.patch | 38 + ...d-hflip-and-vflip-controls-to-ov9281.patch | 112 + ...name-num-soft-gpios-to-avoid-warning.patch | 32 + ...ame-gpio-fsm-property-num-soft-gpios.patch | 38 + ...static-metadata-type-field-numbering.patch | 31 + ...metadata-property-to-the-VC5-HDMI-co.patch | 99 + ...ector-check-to-trigger-mode_change-w.patch | 67 + ...pivid-Fix-crash-when-CMA-alloc-fails.patch | 118 + ...r-dpi-without-DE-and-PCLK-for-VGA666.patch | 30 + ...n-overlay-for-the-VGA666-when-used-w.patch | 153 + ...he-default-DPI-format-to-being-18bpp.patch | 34 + ...how-state-info-in-sys-class-gpio-fsm.patch | 184 + ...io-fsm-Fix-shutdown-timeout-handling.patch | 26 + ...-demo-Ensure-all-LEDs-are-turned-off.patch | 26 + ...7-Remove-auto-frame-length-adjusting.patch | 142 + ...-Add-very-long-exposure-control-to-t.patch | 126 + ...-Fix-up-exposure-calcuations-and-ran.patch | 59 + ...-Handle-exposure-correctly-when-vbla.patch | 42 + .../950-0488-DAC-overlays-4154.patch | 153 + ...7-Fix-crop-height-for-2028x1080-mode.patch | 25 + ...mx477-Replace-existing-1012x760-mode.patch | 197 + ...-Remove-internal-v4l2_mbus_framefmt-.patch | 70 + ...477-Remove-unused-function-parameter.patch | 34 + ...erlays-i2c-rtc-Add-the-Dallas-DS1340.patch | 63 + ...overlays-Update-the-upstream-overlay.patch | 25 + ...-Always-request-for-user-confirmatio.patch | 45 + ...-Always-request-for-user-confirmatio.patch | 43 + ...icam-Fix-bug-in-buffer-swapping-logi.patch | 75 + ...iases-to-different-AES-implementatio.patch | 105 + ...prove-the-i2c-rtc-i2c_csi_dsi-option.patch | 50 + ...n-buffered-mode-run-jobs-if-either-p.patch | 33 + ...codec-Correct-logging-of-size_t-to-z.patch | 34 + ...codec-Add-support-for-pixel-aspect-r.patch | 82 + ...codec-Implement-additional-g_selecti.patch | 35 + ...aging-bcm2835-codec-Add-VC-1-support.patch | 29 + ...rm-Avoid-full-hdmi-audio-fifo-writes.patch | 32 + ...-hdmi-audio-axi-priority-to-avoid-lo.patch | 36 + ...0-0507-overlays-gpio-led-new-overlay.patch | 191 + ...-overlays-Add-pcie-32bit-dma-overlay.patch | 86 + ...2711-Add-aliases-for-additional-SPIs.patch | 55 + ...-fan-less-noisy-in-cool-environments.patch | 24 + ...-source-offsets-with-DRM_FORMAT_P030.patch | 71 + ...ne-Remove-subpixel-positioning-check.patch | 62 + ...-raspberrypi-Also-support-HEVC-clock.patch | 20 + ...-clock-from-fixed-to-firmware-driver.patch | 37 + ...15-rpivid-Request-maximum-hevc-clock.patch | 51 + ...m2835-camera-Add-support-for-DMABUFs.patch | 37 + ...taging-fbtft-Add-minipitft13-variant.patch | 105 + ...518-overlays-Add-minipitft13-overlay.patch | 100 + ...0519-overlays-ghost-amp-Minor-tweaks.patch | 71 + ...ays-Add-README-entry-for-minipitft13.patch | 30 + ...s-update-bcm2711-rpi-cm4.dts-and-400.patch | 205 + ...ix-source-offsets-with-DRM_FORMAT_P0.patch | 30 + ...ix-clang-Wignored-attributes-warning.patch | 36 + ...ang-Wsometimes-uninitialized-warning.patch | 21 + ...ang-Wpointer-bool-conversion-warning.patch | 24 + ...50-0526-Update-Allo-Piano-Dac-Driver.patch | 277 + ...eate-a-helper-to-attach-the-hdr_outp.patch | 99 + ...r-Add-helper-to-compare-HDR-metadata.patch | 168 + ...950-0529-drm-vc4-Use-the-new-helpers.patch | 62 + ...d-a-helper-to-attach-the-colorspace-.patch | 66 + ...nal-the-proper-colorimetry-info-in-t.patch | 50 + ...-Fix-memory-leak-from-not-detaching-.patch | 77 + ...e-Support-2020-colourspace-for-yuv-p.patch | 105 + ...vice-quirks-for-A4Tech-FHD-1080p-web.patch | 45 + ...sb_autopm_get_interface-for-devices-.patch | 33 + ...rlays-ghost-amp-Add-DAC-mute-control.patch | 86 + ...37-clk-Introduce-a-clock-request-API.patch | 284 + ...Convert-to-the-new-clock-request-API.patch | 79 + ...Convert-to-the-new-clock-request-API.patch | 42 + ...m2835-unicam-Switch-to-new-clock-api.patch | 53 + ...-0541-rpivid-Switch-to-new-clock-api.patch | 54 + ...ovide-missing-documentation-for-some.patch | 72 + ...x-a-couple-of-spelling-errors-in-fw_.patch | 34 + ...153_ecm-support-ECM-mode-for-RTL8153.patch | 320 + ...45-net-usb-r8152-use-new-tasklet-API.patch | 41 + ...veral-functions-about-phy-patch-requ.patch | 198 + ...t-the-flow-of-power-cut-for-RTL8153B.patch | 134 + ...152-enable-U1-U2-for-USB_SPEED_SUPER.patch | 47 + ...f-the-pointer-of-the-function-exists.patch | 51 + ...r8152-replace-netif_err-with-dev_err.patch | 36 + ...rtl_set_eee_plus-and-r8153b_green_en.patch | 89 + ...ter-fram-gap-time-depending-on-speed.patch | 75 + ...just-rtl8152_check_firmware-function.patch | 152 + ...8152-add-help-function-to-change-mtu.patch | 157 + .../950-0555-r8152-support-new-chips.patch | 2886 + ...port-PHY-firmware-for-RTL8156-series.patch | 691 + ...rch-the-configuration-of-vendor-mode.patch | 79 + ...58-rpivid-Only-clk_request_done-once.patch | 26 + ...9-dwc_otg-fix-an-undeclared-variable.patch | 24 + ...rv-Remove-the-DSI-pointer-in-vc4_drv.patch | 66 + ...snprintf-for-the-PHY-clocks-instead-.patch | 66 + ...c4-dsi-Introduce-a-variant-structure.patch | 191 + ...563-drm-vc4-dsi-Add-support-for-DSI0.patch | 44 + ...i-Add-configuration-for-BCM2711-DSI1.patch | 53 + ...drm-vc4-Correct-pixel-order-for-DSI0.patch | 27 + ...-dsi0-as-the-correct-vc4-encoder-typ.patch | 29 + ...7-drm-vc4-Fix-dsi0-interrupt-support.patch | 188 + ...ect-stop-condition-to-vc4_dsi_encode.patch | 30 + ...-fixup-modes-that-haven-t-been-reset.patch | 24 + ...070me05000-Use-gpiod_set_value_cansl.patch | 67 + ...verlays-for-JDI-LT070ME05000-1200x19.patch | 216 + ...quests-Ignore-if-the-pointer-is-null.patch | 22 + ...-drm-vc4-hvs-Make-the-HVS-bind-first.patch | 41 + ...-Properly-compute-the-BVB-clock-rate.patch | 55 + ...75-drm-vc4-hdmi-Enable-the-scrambler.patch | 142 + ...c4-hdmi-Raise-the-maximum-clock-rate.patch | 30 + ...i-Handle-case-when-bvb-clock-is-null.patch | 45 + ...erlays-spi-rtc-Add-ds3232-and-ds3234.patch | 125 + ...address-for-BCM2711-in-the-devicetre.patch | 72 + ...vc4-Separate-VEC-compatible-variants.patch | 106 + ...eference-the-request-pointer-after-t.patch | 30 + ...codec-Fix-support-for-levels-4.1-and.patch | 36 + ...codec-Set-the-colourspace-appropriat.patch | 83 + ...cm2835-codec-Pass-corrupt-frame-flag.patch | 42 + ...camera-Add-support-for-H264-levels-4.patch | 58 + ...codec-Do-not-update-crop-from-S_FMT-.patch | 36 + ...ing-bcm2835-isp-Fix-compiler-warning.patch | 25 + ...low-multiple-gpio-shutdown-instances.patch | 42 + ...ADME-improve-the-gpio-poweroff-guide.patch | 30 + ...0-SQUASH-overlays-Fix-typo-in-README.patch | 21 + ...ff-Remember-the-old-poweroff-handler.patch | 53 + ...LCLK-modes-even-if-horz-timing-is-od.patch | 42 + ...overlays-Add-ugreen-dabboard-overlay.patch | 101 + ...m2711-rpi-400-Limit-MDIO-clock-speed.patch | 23 + ...-bcm2835-Increase-the-CS-limit-to-24.patch | 38 + ...96-clk-Always-clamp-the-rounded-rate.patch | 28 + ...ss-the-drm_atomic_state-to-config_pv.patch | 46 + ...-crtc-Fix-vc4_get_crtc_encoder-logic.patch | 83 + ...kup-the-encoder-from-the-register-at.patch | 104 + ...mplify-the-connector-state-retrieval.patch | 52 + ...Rely-on-interrupts-to-handle-hotplug.patch | 78 + ...mi-Add-a-workqueue-to-set-scrambling.patch | 91 + ...vc4-drm-hdmi-Fix-missing-declaration.patch | 21 + ...erlays-merus-amp-remove-spi-override.patch | 27 + ...2c-ov5647-Correct-pixel-array-offset.patch | 25 + ...-ov5647-Correct-minimum-VBLANK-value.patch | 26 + ...-Fix-v4l2-compliance-failure-subscri.patch | 34 + ...ys-Add-pinctrl-names-to-i2c0-overlay.patch | 25 + ...e-__symbols__-i2c0-from-i2c0-overlay.patch | 31 + ...ove-the-need-to-have-num_entry_point.patch | 980 + ...-0611-media-rpivid-Convert-to-MPLANE.patch | 329 + ...-Add-an-enable-count-to-irq-claim-Qs.patch | 234 + ...dia-Add-media_request_-pin-unpin-API.patch | 94 + ...-a-Pass0-to-accumulate-slices-and-re.patch | 1049 + ...media-rpivid-Map-cmd-buffer-directly.patch | 160 + ...rove-values-returned-when-setting-ou.patch | 216 + ...rove-stream_on-off-conformance-clock.patch | 260 + ...rove-SPS-PPS-error-handling-validati.patch | 256 + ...ensirion-sgp30-to-i2c-sensor-overlay.patch | 54 + ...s-Remove-deleted-merus-amp-parameter.patch | 23 + ...bh1750-and-ccs811-to-i2c-sensor-4334.patch | 96 + ...622-Add-Raspberry-Pi-PoE-HAT-support.patch | 394 + ...23-overlays-Add-rpi-poe-plus-overlay.patch | 75 + ...nge-of-Broadcast-RGB-mode-needs-a-mo.patch | 62 + ...-ssd1331-spi-support-for-OLED-screen.patch | 129 + ...-clock-detection-problem-of-the-PRO-.patch | 38 + ...mpressed-frames-to-set-sizeimage-438.patch | 47 + ...-Fix-for-long-exposure-limit-calcula.patch | 26 + ...st-amp-Change-early-disable-sequence.patch | 43 + ...vc4-Make-vc4_crtc_get_encoder-public.patch | 45 + ...codec-Support-IEC958-encoded-PCM-for.patch | 53 + ...odec-Rework-to-support-more-controls.patch | 76 + ...ec958-split-status-creation-and-fill.patch | 209 + ...-ASoC-hdmi-codec-Add-iec958-controls.patch | 113 + ...5-ASoC-hdmi-codec-Add-a-prepare-hook.patch | 202 + ...950-0636-drm-vc4-Register-HDMI-codec.patch | 492 + ...-vc4-hdmi-Remove-redundant-variables.patch | 111 + ...1-Tune-DMA-parameters-for-HDMI-audio.patch | 35 + ...oup-Disable-cgroup-memory-by-default.patch | 85 + ...90-Support-60fps-in-2-lane-operation.patch | 309 + ...90-Fix-the-pixel-rate-at-148.5Mpix-s.patch | 49 + ...-Fix-clock-setup-register-assignment.patch | 49 + ...-encoder-to-vc4_crtc_config_pv-proto.patch | 43 + ...ork-the-encoder-retrieval-code-again.patch | 96 + ...0-0645-drm-vc4-crtc-Add-some-logging.patch | 38 + ...rage-the-load-tracker-on-the-BCM2711.patch | 121 + ...vc4-Fix-timings-for-interlaced-modes.patch | 83 + ...on-t-create-hvs_load_tracker-on-fkms.patch | 23 + ...-H265-aux-ent-reuse-of-the-same-slot.patch | 151 + ...-interface-in-mode6-for-18-bit-color.patch | 214 + ...-dpi18cpadhi-vc4-kms-dpi-at056tn53v1.patch | 163 + ...x-pixel-wrap-issue-with-DVP-teardown.patch | 62 + ...v9281-Remove-override-of-subdev-name.patch | 28 + ...-a-fixed-rate-for-the-HSM-clock-on-B.patch | 140 + ...Enable-the-scrambler-on-reconnection.patch | 54 + ...vices-isp-Set-the-YUV420-YVU420-form.patch | 39 + ...vicetree-Add-documentation-for-imx37.patch | 142 + ...erlays-Add-overlay-for-imx378-sensor.patch | 288 + ...-Extend-driver-to-support-imx378-sen.patch | 190 + ...-i2c-rtc-and-i2c-rtc-gpio-share-RTCs.patch | 918 + ...k-raspberrypi-Remove-unused-property.patch | 40 + ...play-vc4-Add-phandle-to-the-firmware.patch | 31 + ...rypi-Add-RPI_FIRMWARE_NOTIFY_DISPLAY.patch | 25 + ...onflicting-framebuffers-before-calli.patch | 35 + ...y-the-firmware-when-DRM-is-in-charge.patch | 54 + ...dts-rpi-Add-the-firmware-node-to-vc4.patch | 40 + ...-the-device-on-error-in-pre_crtc_con.patch | 65 + ...it-the-CEC-disable-enable-functions-.patch | 109 + ...e-sure-the-device-is-powered-with-CE.patch | 45 + ...-missing-clk_disable_unprepare-on-er.patch | 28 + ...n-if-we-access-the-controller-while-.patch | 47 + ...e-initial-register-read-after-pm_run.patch | 37 + ...ify-firmware-of-display-done-with-km.patch | 43 + ...g-Update-NetBSD-usb.h-header-licence.patch | 33 + ...p-devm-interrupt-handler-for-CEC-int.patch | 106 + ...p-devm-interrupt-handler-for-hotplug.patch | 111 + ...y-call-into-DRM-framework-if-registe.patch | 35 + ...rmal-Don-t-clamp-temperature-at-zero.patch | 24 + ...icam-Forward-input-status-from-subde.patch | 53 + ...d-overlay-for-Chipdip-I2S-master-DAC.patch | 94 + ...duce-an-atomic_commit_setup-function.patch | 95 + ...-after-free-gotcha-with-private-obje.patch | 44 + ...mplify-a-bit-the-global-atomic_check.patch | 44 + ...-t-poll-for-the-infoframes-status-on.patch | 63 + ...n-the-HVS-atomic-hooks-to-the-new-AP.patch | 87 + ...ate-pointer-directly-in-atomic_check.patch | 136 + ...nnecessary-drm_plane_cleanup-wrapper.patch | 39 + ...c4-plane-Remove-redundant-assignment.patch | 26 + ...9-drm-automatic-legacy-gamma-support.patch | 458 + ...l-state-to-connectors-atomic-functio.patch | 371 + ...c4-replace-idr_init-by-idr_init_base.patch | 32 + ..._regs-Mark-some-data-sets-as-__maybe.patch | 59 + ...drm-vc4-remove-unneeded-variable-ret.patch | 35 + ...rlay-for-cap1106-capacitive-touch-se.patch | 94 + ...in-calculations-for-the-right-bottom.patch | 38 + ...x-margin-calculations-for-the-right-.patch | 38 + ...cm2711-fold-in-the-correct-interrupt.patch | 33 + ...d-overlay-for-Si446x-Transceiver-SPI.patch | 100 + ...99-drm-vc4-Fix-timings-for-VEC-modes.patch | 148 + ...drm-vc4-Refactor-VEC-TV-mode-setting.patch | 167 + ...drm-vc4-Fix-definition-of-PAL-M-mode.patch | 77 + ...support-for-more-analog-TV-standards.patch | 148 + ...tting-the-TV-norm-via-module-paramet.patch | 144 + ...drm-vc4-Refactor-mode-checking-logic.patch | 85 + ...-Fix-typo-when-getting-firmware-node.patch | 21 + ...ts-bcm2711-Tidy-the-HDMI-I2C-aliases.patch | 110 + ...477-Fix-framerates-for-1332x990-mode.patch | 25 + ...0708-drm-uapi-Add-USB-connector-type.patch | 49 + ...-0709-drm-Add-GUD-USB-Display-driver.patch | 2676 + .../950-0710-drm-gud-fix-sizeof-use.patch | 38 + ...11-drm-gud-Remove-unneeded-semicolon.patch | 73 + ...2-drm-gud-cleanup-coding-style-a-bit.patch | 41 + ...m-gud-Free-buffers-on-device-removal.patch | 60 + ...Use-scatter-gather-USB-bulk-transfer.patch | 204 + ...715-drm-gud-Add-Raspberry-Pi-Pico-ID.patch | 31 + ...gud-Add-async_flush-module-parameter.patch | 55 + ...e-sure-the-controller-is-powered-up-.patch | 65 + ...ays-Set-CMA-to-512MB-on-Pi-4-for-vc4.patch | 151 + ...ARM-dts-Correct-CM4-PHY-MDIO-address.patch | 29 + ...ase-the-core-clock-based-on-HVS-load.patch | 249 + ...-the-core-clock-to-a-minimum-of-500M.patch | 40 + ...te-and-rename-chipdip-i2s-master-dac.patch | 148 + ...0723-ASoC-bcm-Add-chipdip-dac-driver.patch | 325 + ...50-0724-char-vc_mem-Delete-dead-code.patch | 24 + ...dd-Ablic-S35390A-to-i2c-rtc-and-gpio.patch | 73 + ...rientation-and-rotation-parameter-to.patch | 210 + ...mx290-Add-fwnode-properties-controls.patch | 48 + ...v9281-Add-fwnode-properties-controls.patch | 56 + ...v7251-Add-fwnode-properties-controls.patch | 48 + ...ys-Reduce-Pi-4-vc4-CMA-size-to-320MB.patch | 42 + ...Update-display-GPIO-declarations-for.patch | 24 + ...rlays-Add-midi-uart-2345-overlay.dts.patch | 234 + ...und-for-bogus-SET_DEQ_PENDING-endpoi.patch | 41 + ...-overlays-Add-TI-BQ32000-RTC-support.patch | 102 + ...ses-to-ep_state-in-xhci_endpoint_res.patch | 43 + ...36-ARM-dts-Adapt-to-upstream-changes.patch | 304 + ...-poe-plus-Improve-the-cooling-levels.patch | 29 + ...efiles-dt-Always-set-on-ARCH_BCM2835.patch | 35 + .../960-hwrng-iproc-set-quality-to-1000.patch | 25 + 745 files changed, 227568 insertions(+), 2 deletions(-) create mode 100644 target/linux/bcm27xx/bcm2708/config-5.10 create mode 100644 target/linux/bcm27xx/bcm2709/config-5.10 create mode 100644 target/linux/bcm27xx/bcm2710/config-5.10 create mode 100644 target/linux/bcm27xx/bcm2711/config-5.10 create mode 100644 target/linux/bcm27xx/patches-5.10/950-0001-arm-partially-revert-702b94bff3c50542a6e4ab9a4f4cef0.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0002-Revert-rtc-pcf8523-properly-handle-oscillator-stop-b.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0003-Revert-staging-bcm2835-audio-Drop-DT-dependency.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0004-Revert-spi-spidev-Fix-CS-polarity-if-GPIO-descriptor.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0005-Revert-mailbox-avoid-timer-start-from-callback.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0006-smsx95xx-fix-crimes-against-truesize.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0007-smsc95xx-Experimental-Enable-turbo_mode-and-packetsi.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0008-Allow-mac-address-to-be-set-in-smsc95xx.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0009-Protect-__release_resource-against-resources-without.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0010-irq-bcm2836-Avoid-Invalid-trigger-warning.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0011-irqchip-bcm2835-Add-FIQ-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0012-irqchip-irq-bcm2835-Add-2836-FIQ-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0013-spi-spidev-Completely-disable-the-spidev-warning.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0014-dmaengine-bcm2835-Load-driver-early-and-support-lega.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0015-firmware-Updated-mailbox-header.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0016-rtc-Add-SPI-alias-for-pcf2123-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0017-watchdog-bcm2835-Support-setting-reboot-partition.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0018-reboot-Use-power-off-rather-than-busy-spinning-when-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0019-bcm-Make-RASPBERRYPI_POWER-depend-on-PM.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0020-Register-the-clocks-early-during-the-boot-process-so.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0021-bcm2835-rng-Avoid-initialising-if-already-enabled.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0022-clk-bcm2835-Mark-used-PLLs-and-dividers-CRITICAL.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0023-clk-bcm2835-Add-claim-clocks-property.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0024-clk-bcm2835-Read-max-core-clock-from-firmware.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0025-sound-Demote-deferral-errors-to-INFO-level.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0026-Update-vfpmodule.c.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0027-i2c-bcm2835-Add-debug-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0028-mm-Remove-the-PFN-busy-warning.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0029-irqchip-irq-bcm2836-Remove-regmap-and-syscon-use.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0030-lan78xx-Enable-LEDs-and-auto-negotiation.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0031-amba_pl011-Don-t-use-DT-aliases-for-numbering.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0032-amba_pl011-Round-input-clock-up.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0033-amba_pl011-Insert-mb-for-correct-FIFO-handling.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0034-amba_pl011-Add-cts-event-workaround-DT-property.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0035-tty-amba-pl011-Make-TX-optimisation-conditional.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0036-tty-amba-pl011-Add-un-throttle-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0037-tty-amba-pl011-Avoid-rare-write-when-full-error.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0038-pinctrl-bcm2835-Set-base-to-0-give-expected-gpio-num.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0039-Main-bcm2708-bcm2709-linux-port.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0040-Add-dwc_otg-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0041-bcm2708-framebuffer-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0042-Pulled-in-the-multi-frame-buffer-support-from-the-Pi.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0043-fbdev-add-FBIOCOPYAREA-ioctl.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0044-Speed-up-console-framebuffer-imageblit-function.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0045-dmaengine-Add-support-for-BCM2708.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0046-MMC-added-alternative-MMC-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0047-Adding-bcm2835-sdhost-driver-and-an-overlay-to-enabl.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0048-vc_mem-Add-vc_mem-driver-for-querying-firmware-memor.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0049-Add-dev-gpiomem-device-for-rootless-user-GPIO-access.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0050-Add-SMI-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0051-Add-Chris-Boot-s-i2c-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0052-char-broadcom-Add-vcio-module.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0053-firmware-bcm2835-Support-ARCH_BCM270x.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0054-BCM2708-Add-core-Device-Tree-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0055-BCM270x_DT-Add-pwr_led-and-the-required-input-trigge.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0056-Added-Device-IDs-for-August-DVB-T-205.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0057-Improve-__copy_to_user-and-__copy_from_user-performa.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0058-gpio-poweroff-Allow-it-to-work-on-Raspberry-Pi.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0059-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0060-Add-support-for-all-the-downstream-rpi-sound-card-dr.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0061-Fixes-a-problem-when-module-probes-before-i2c-module.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0062-rpi_display-add-backlight-driver-and-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0063-bcm2835-virtgpio-Virtual-GPIO-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0064-OF-DT-Overlay-configfs-interface.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0065-hci_h5-Don-t-send-conf_req-when-ACTIVE.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0066-ARM64-Round-Robin-dispatch-IRQs-between-CPUs.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0067-ARM64-Force-hardware-emulation-of-deprecated-instruc.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0068-cache-export-clean-and-invalidate.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0069-AXI-performance-monitor-driver-2222.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0070-ARM-bcm2835-Set-Serial-number-and-Revision.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0071-dwc-otg-FIQ-Fix-bad-mode-in-data-abort-handler.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0072-ARM-Activate-FIQs-to-avoid-__irq_startup-warnings.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0073-raspberrypi-firmware-Export-the-general-transaction-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0074-i2c-gpio-Also-set-bus-numbers-from-reg-property.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0075-added-capture_clear-option-to-pps-gpio-via-dtoverlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0076-lan78xx-Read-initial-EEE-status-from-DT.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0077-hid-Reduce-default-mouse-polling-interval-to-60Hz.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0078-Add-ability-to-export-gpio-used-by-gpio-poweroff.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0079-firmware-raspberrypi-Notify-firmware-of-a-reboot.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0080-irqchip-irq-bcm2835-Calc.-FIQ_START-at-boot-time.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0081-of-configfs-Use-of_overlay_fdt_apply-API-call.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0082-net-lan78xx-Disable-TCP-Segmentation-Offload-TSO.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0083-lan78xx-Move-enabling-of-EEE-into-PHY-init-code.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0084-Add-rpi-poe-fan-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0085-cxd2880-CXD2880_SPI_DRV-should-select-DVB_CXD2880-wi.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0086-hwmon-raspberrypi-Prevent-voltage-low-warnings-from-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0087-firmware-raspberrypi-Add-backward-compatible-get_thr.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0088-sc16is7xx-Don-t-spin-if-no-data-received.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0089-drivers-thermal-step_wise-add-support-for-hysteresis.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0090-drivers-thermal-step_wise-avoid-throttling-at-hyster.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0091-Update-issue-templates-2736.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0092-net-lan78xx-Support-auto-downshift-to-100Mb-s.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0093-firmware-raspberrypi-Report-the-fw-variant-during-pr.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0094-lan78xx-Debounce-link-events-to-minimize-poll-storm.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0095-lan78xx-EEE-support-is-now-a-PHY-property.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0096-bcm2835-dma-Add-support-for-per-channel-flags.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0097-rtc-rv3028-Add-backup-switchover-mode-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0098-lan78xx-use-default-alignment-for-rx-buffers.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0099-media-ov5647-Add-set_fmt-and-get_fmt-calls.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0100-media-ov5647-Add-support-for-PWDN-GPIO.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0101-media-ov5647-Add-support-for-non-continuous-clock-mo.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0102-media-tc358743-Increase-FIFO-level-to-374.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0103-media-tc358743-fix-connected-active-CSI-2-lane-repor.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0104-media-tc358743-Add-support-for-972Mbit-s-link-freq.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0105-media-tc358743-Check-I2C-succeeded-during-probe.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0106-media-adv7180-Default-to-the-first-valid-input.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0107-media-adv7180-Add-YPrPb-support-for-ADV7282M.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0108-media-videodev2-Add-helper-defines-for-printing-FOUR.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0109-dt-bindings-Document-BCM283x-CSI2-CCP2-receiver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0110-MAINTAINERS-Add-entry-for-BCM2835-Unicam-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0111-media-tc358743-Return-an-appropriate-colorspace-from.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0112-staging-mmal-vchiq-Avoid-use-of-bool-in-structures.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0113-staging-mmal-vchiq-Add-support-for-event-callbacks.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0114-staging-vc04_services-Support-sending-data-to-MMAL-p.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0115-media-videobuf2-Allow-exporting-of-a-struct-dmabuf.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0116-staging-mmal-vchiq-Fix-client_component-for-64-bit-k.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0117-clk-clk-bcm2835-Use-zd-when-printing-size_t.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0118-media-ov5647-Use-gpiod_set_value_cansleep.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0119-staging-mmal_vchiq-Add-in-the-Bayer-encoding-formats.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0120-staging-mmal-vchiq-Update-mmal_parameters.h-with-rec.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0121-staging-mmal-vchiq-Free-the-event-context-for-contro.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0122-staging-mmal-vchiq-Fix-memory-leak-in-error-path.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0123-w1-w1-gpio-Make-GPIO-an-output-for-strong-pullup.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0124-arm-bcm2835-Fix-FIQ-early-ioremap.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0125-arm-bcm2835-DMA-can-only-address-1GB.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0126-hwrng-iproc-rng200-Add-BCM2838-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0127-mmc-sdhci-iproc-Fix-vmmc-regulators-on-iProc.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0128-vchiq-Add-36-bit-address-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0129-bcm2835-pcm.c-Support-multichannel-audio.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0130-bcmgenet-constrain-max-DMA-burst-length.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0131-bcmgenet-Better-coalescing-parameter-defaults.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0132-net-genet-enable-link-energy-detect-powerdown-for-ex.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0133-spi-bcm2835-enable-shared-interrupt-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0134-clk-bcm2835-Don-t-wait-for-pllh-lock.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0135-soc-bcm-bcm2835-pm-Add-support-for-2711.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0136-clk-bcm2835-Add-support-for-setting-leaf-clock-rates.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0137-clk-bcm2835-Allow-reparenting-leaf-clocks-while-they.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0138-usb-add-plumbing-for-updating-interrupt-endpoint-int.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0139-xhci-implement-xhci_fixup_endpoint-for-interval-adju.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0140-usbhid-call-usb_fixup_endpoint-after-mangling-interv.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0141-arm-bcm2835-Add-bcm2838-compatible-string.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0142-drm-v3d-Add-support-for-2711.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0143-drm-v3d-Skip-MMU-flush-if-the-device-is-currently-of.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0144-drm-v3d-Hook-up-the-runtime-PM-ops.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0146-i2c-bcm2835-Set-clock-stretch-timeout-to-35ms.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0147-clk-bcm2835-Avoid-null-pointer-exception.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0148-drm-v3d-HACK-gut-runtime-pm-for-now.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0149-drm-v3d-Clock-V3D-down-when-not-in-use.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0150-drivers-char-add-chardev-for-mmap-ing-the-RPiVid-con.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0151-hid-usb-Add-device-quirks-for-Freeway-Airmouse-T3-an.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0152-Add-HDMI1-facility-to-the-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0153-net-bcmgenet-Workaround-2-for-Pi4-Ethernet-fail.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0154-xhci-Use-more-event-ring-segment-table-entries.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0155-configs-arm64-bcm2711-Enable-V3D.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0156-arch-arm-Add-model-string-to-cpuinfo.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0157-arch-arm64-Add-Revision-Serial-Model-to-cpuinfo.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0158-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0159-v4l2-Add-a-Greyworld-AWB-mode.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0160-staging-bcm2835-camera-Add-greyworld-AWB-mode.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0161-drm-v3d-Delete-pm_runtime-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0162-kbuild-Allow-.dtbo-overlays-to-be-built-piecemeal.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0163-ARM-bcm-Switch-board-clk-and-pinctrl-to-bcm2711-comp.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0164-Rename-HDMI-ALSA-device-names-check-for-enable-state.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0165-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0166-media-i2c-Add-a-driver-for-the-Infineon-IRS1125-dept.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0167-drm-v3d-Don-t-clear-MMU-control-bits-on-exception.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0168-drm-v3d-Suppress-all-but-the-first-MMU-error.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0169-drm-v3d-Plug-dma_fence-leak.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0170-staging-vchiq_arm-Register-vcsm-cma-as-a-platform-dr.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0171-staging-vchiq_arm-Register-bcm2835-codec-as-a-platfo.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0172-net-bcmgenet-The-second-IRQ-is-optional.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0173-net-phy-2711-Allow-ethernet-LED-mode-to-be-set-via-d.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0174-net-phy-2711-Change-the-default-ethernet-LED-actions.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0175-v3d_drv-Handle-missing-clock-more-gracefully.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0176-v3d_gem-Kick-the-clock-so-firmware-knows-we-are-usin.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0177-clk-raspberrypi-Allow-cpufreq-driver-to-also-adjust-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0178-clk-bcm2835-Disable-v3d-clock.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0179-drm-v3d-Set-dma_mask-as-well-as-coherent_dma_mask.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0180-staging-vchiq_arm-Set-up-dma-ranges-on-child-devices.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0181-staging-vchiq-Use-the-old-dma-controller-for-OF-conf.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0182-ARM-bcm-Backport-BCM2711-support-from-upstream.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0183-Initialise-rpi-firmware-before-clk-bcm2835.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0184-staging-vchiq_arm-Give-vchiq-children-DT-nodes.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0185-pinctrl-bcm2835-Remove-gpiochip-on-error.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0186-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0187-pinctrl-bcm2835-Accept-fewer-than-expected-IRQs.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0188-drivers-char-vcio-Use-common-compat-header.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0189-video-fbdev-bcm2708_fb-Use-common-compat-header.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0190-of-overlay-Correct-symbol-path-fixups.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0191-dt-bindings-pci-Add-DT-docs-for-Brcmstb-PCIe-device.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0192-Kbuild-Allow-.dtbo-overlays-to-be-built-adjust.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0193-bcmgenet-Disable-skip_umac_reset-by-default.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0194-drm-fourcc-Add-packed-10bit-YUV-4-2-0-format.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0195-media-uapi-hevc-Add-scaling-matrix-control.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0196-media-uapi-hevc-Add-segment-address-field.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0197-media-uapi-Add-hevc-ctrls-for-WPP-decoding.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0198-media-videodev2.h-Add-a-format-for-column-YUV4-2-0-m.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0199-media-dt-bindings-media-Add-binding-for-the-Raspberr.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0200-staging-media-Add-Raspberry-Pi-V4L2-H265-decoder.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0201-mmc-sdhci-Silence-MMC-warnings.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0202-dt-bindings-clock-Add-a-binding-for-the-RPi-Firmware.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0203-dt-bindings-display-vc4-hdmi-Add-BCM2711-HDMI-contro.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0204-drm-Checking-of-the-pitch-is-only-valid-for-linear-f.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0205-overlays-Fix-dtc-warnings-in-i2c-gpio.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0206-driver-char-rpivid-Remove-legacy-name-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0207-spi-Force-CS_HIGH-if-GPIO-descriptors-are-used.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0208-driver-char-rpivid-Don-t-map-more-than-wanted.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0209-media-bcm2835-unicam-Driver-for-CCP2-CSI2-camera-int.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0210-media-uapi-v4l2-core-Add-sensor-ancillary-data-V4L2-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0211-media-uapi-Add-MEDIA_BUS_FMT_SENSOR_DATA-media-bus-f.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0212-media-bcm2835-unicam-Add-support-for-mulitple-device.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0213-media-bcm2835-unicam-Add-embedded-data-node.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0214-media-bcm2835-unicam-Use-dummy-buffer-if-none-have-b.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0215-media-bcm2835-unicam-Disable-event-related-ioctls-on.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0216-media-bcm2835-unicam-Add-support-for-the-FRAME_SYNC-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0217-media-imx219-Advertise-embedded-data-node-on-media-p.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0218-media-bcm2835-unicam-Re-fetch-mbus-code-from-subdev-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0219-media-uapi-v4l2-core-Add-ISP-statistics-output-V4L2-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0220-media-uapi-v4l-ctrls-Add-CID-base-for-the-bcm2835-is.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0221-staging-vchiq-Load-bcm2835_isp-driver-from-vchiq.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0222-bcm2835-dma-Add-proper-40-bit-DMA-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0223-overlays-Make-the-i2c-gpio-overlay-safe-again.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0224-media-i2c-imx219-Declare-that-the-driver-can-create-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0225-media-ov5647-Fix-return-codes-from-ov5647_write-ov56.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0226-media-ov5647-Add-basic-support-for-multiple-sensor-m.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0227-media-ov5647-Add-V4L2-controls-for-analogue-gain-exp.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0228-media-ov5647-Add-extra-10-bit-sensor-modes.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0229-media-ov5647-change-defaults-to-better-match-raw-cam.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0230-media-i2c-ov5647-Add-support-for-g_selection-to-refl.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0231-media-i2c-ov5467-Fixup-error-path-to-release-mutex.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0232-media-i2c-ov5647-Support-V4L2_CID_PIXEL_RATE.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0233-media-i2c-ov5647-Set-V4L2_SUBDEV_FL_HAS_EVENTS-flag.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0234-media-i2c-ov5647-Add-support-for-V4L2_CID_VBLANK.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0235-media-i2c-ov5647-Neither-analogue-gain-nor-exposure-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0236-media-i2c-ov5647-Use-member-names-in-mode-tables.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0237-media-i2c-ov5647-Advertise-the-correct-exposure-rang.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0238-media-bcm2835-unicam-Add-support-for-VIDIOC_-S-G-_SE.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0239-media-bcm2835-unicam-Do-not-stop-streaming-in-unicam.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0240-media-bcm2835-unicam-Fix-reference-counting-in-unica.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0241-media-i2c-tc358743-Fix-fallthrough-warning.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0242-media-bcm2835-unicam-Fix-uninitialized-warning.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0243-video-bcm2708_fb-Disable-FB-if-no-displays-found.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0244-dt-bindings-media-i2c-Add-IMX477-CMOS-sensor-binding.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0245-media-bcm2835-unicam-Always-service-interrupts.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0246-sc16is7xx-Fix-for-hardware-flow-control.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0247-staging-vc04_services-mmal-vchiq-Update-parameters-l.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0248-staging-vc04_services-bcm2835-camera-Request-headers.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0249-kbuild-Disable-gcc-plugins.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0250-media-bcm2835-unicam-Retain-packing-information-on-G.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0251-zswap-Defer-zswap-initialisation.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0252-SQUASH-pinctrl-bcm2835-Set-base-for-bcm2711-GPIO-to-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0253-staging-vchiq_arm-Clean-up-40-bit-DMA-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0254-media-bcm2835-unicam-change-minimum-number-of-vb2_qu.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0255-snd_bcm2835-disable-HDMI-audio-when-vc4-is-used-3640.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0256-gpiolib-Don-t-prevent-IRQ-usage-of-output-GPIOs.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0257-PCI-brcmstb-Add-DT-property-to-control-L1SS.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0258-media-irs1125-Using-i2c_transfer-for-ic2-reads.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0259-media-irs1125-Refactoring-and-debug-messages.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0260-media-irs1125-Atomic-access-to-imager-reconfiguratio.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0261-media-irs1125-Keep-HW-in-sync-after-imager-reset.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0262-staging-bcm2835-audio-Add-missing-MODULE_ALIAS.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0263-drivers-media-Remove-the-downstream-version-of-bcm28.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0264-media-bcm2835-unicam-Driver-for-CCP2-CSI2-camera-int.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0265-media-bcm2835-unicam-Add-support-for-get_mbus_config.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0266-media-bcm2835-unicam-Avoid-gcc-warning-over-0-on-end.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0267-media-i2c-imx290-set-the-format-before-VIDIOC_SUBDEV.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0268-media-i2c-imx290-Add-support-for-74.25MHz-clock.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0269-media-i2c-imx290-Correct-range-for-V4L2_CID_GAIN-to-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0270-media-i2c-imx290-Convert-HMAX-setting-into-V4L2_CID_.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0271-media-i2c-imx290-Add-support-for-V4L2_CID_VBLANK.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0272-media-i2c-imx290-Add-exposure-control-to-the-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0273-media-i2c-imx290-Add-H-and-V-flip-controls.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0274-media-dt-bindings-media-i2c-Add-mono-version-to-IMX2.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0275-media-i2c-imx290-Add-support-for-the-mono-sensor-var.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0276-media-i2c-imx290-Switch-set_hmax-to-use-imx290_write.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0277-serial-8250-bcm2835aux-defer-if-clock-is-zero.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0278-media-Add-a-pixel-format-for-MIPI-packed-12bit-luma-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0279-media-Add-a-pixel-format-for-MIPI-packed-14bit-luma-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0280-media-bcm2835-unicam-Add-support-for-12bit-mono-pack.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0281-media-bcm2835-unicam-Add-support-for-14bit-mono-sour.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0282-media-bcm2835-unicam-Add-support-for-unpacked-14bit-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0283-bcm2835-dma-Add-NO_WAIT_RESP-flag.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0284-media-i2c-add-ov9281-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0285-media-i2c-ov9281-fix-mclk-issue-when-probe-multiple-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0286-media-i2c-ov9281-add-enum_frame_interval-function-fo.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0287-media-i2c-ov9281-Fixup-for-recent-kernel-releases-an.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0288-media-i2c-ov9281-Read-chip-ID-via-2-reads.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0289-media-i2c-imx290-Explicitly-set-v-h-blank-on-mode-ch.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0290-media-i2c-imx290-Add-support-for-g_selection-to-repo.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0291-media-i2c-imx290-Set-the-colorspace-fields-in-the-fo.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0292-media-bcm2835-unicam-Reinstate-V4L2_CAP_READWRITE-in.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0293-media-bcm2835-unicam-Ensure-type-is-VIDEO_CAPTURE-in.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0294-media-bcm2835-unicam-Set-VPU-min-clock-freq-to-250Mh.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0295-dt-bindings-bcm2835-unicam-Update-documentation-with.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0296-media-i2c-ov5647-Parse-and-register-properties.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0297-leds-Add-the-actpwr-trigger.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0298-staging-vchiq_arm-children-inherit-DMA-config.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0299-bcm2835-dma-Advertise-the-full-DMA-range.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0300-ARM-proc-v7-Force-misalignment-of-early-stmia.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0301-media-bcm2835-unicam-Select-MEDIA_CONTROLLER-and-VID.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0302-staging-media-rpivid-Select-MEDIA_CONTROLLER-and-MED.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0303-media-bcm2835-unicam-Drop-WARN-on-uing-direct-cache-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0304-media-i2c-tc358743-Only-allow-supported-pixel-fmts-i.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0305-media-i2c-ov9281-Add-support-for-8-bit-readout.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0306-bcm2835-mmc-uninitialized_var-is-no-more.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0307-dwc_otg-whitelist_table-is-now-productlist_table.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0308-vchiq_2835_arm-Implement-a-DMA-pool-for-small-bulk-t.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0309-include-firmware-Add-enum-for-RPI_FIRMWARE_FRAMEBUFF.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0310-vc4_hdmi-Remove-cec_available-flag-as-always-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0311-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0312-vc4_hdmi-Set-HD_CTL_WHOLSMP-and-HD_CTL_CHALIGN_SET.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0313-vc4_hdmi-Set-HDMI_MAI_FMT.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0314-drm-vc4-add-iec958-controls-to-vc4_hdmi.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0315-drm-vc4-move-setup-from-hw_params-to-prepare.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0316-drm-vc4-enable-HBR-MAI-format-on-HBR-streams.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0317-vc4_hdmi-Remove-firmware-logic-for-MAI-threshold-set.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0318-vc_hdmi-Set-VC4_HDMI_MAI_CONFIG_FORMAT_REVERSE.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0319-drm-vc4-Add-support-for-DRM_FORMAT_P030-to-vc4-plane.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0320-drm-vc4-Add-support-for-YUV-color-encodings-and-rang.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0321-drm-vc4-Add-firmware-kms-mode.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0322-drm-vc4-Add-FKMS-as-an-acceptable-node-for-dma-range.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0323-media-i2c-Add-driver-for-Sony-IMX477-sensor.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0324-media-i2c-imx477-Add-support-for-adaptive-frame-cont.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0325-media-i2c-imx477-Return-correct-result-on-sensor-id-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0326-media-i2c-imx477-Parse-and-register-properties.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0327-media-bcm2835-unicam-Always-service-interrupts.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0328-media-bcm2835-unicam-Fix-uninitialized-warning.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0329-media-bcm2835-unicam-Fixup-review-comments-from-Hans.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0330-media-bcm2835-unicam-Retain-packing-information-on-G.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0331-media-bcm2835-unicam-change-minimum-number-of-vb2_qu.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0332-staging-fbtft-Add-support-for-display-variants.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0333-rpivid_h265-Fix-width-height-typo.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0334-net-bcmgenet-Reset-RBUF-on-first-open.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0335-char-Add-broadcom-char-drivers-back-to-build-files.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0336-dwc_otg-initialise-sched_frame-for-periodic-QHs-that.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0337-staging-bcm2835-camera-Replace-deprecated-V4L2_PIX_F.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0338-staging-vc04_services-Add-new-vc-sm-cma-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0339-staging-vchiq-mmal-Add-support-for-14bit-Bayer.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0340-staging-mmal-vchiq-Add-monochrome-image-formats.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0341-staging-mmal-vchiq-Use-vc-sm-cma-to-support-zero-cop.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0342-staging-vc04_services-Add-a-V4L2-M2M-codec-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0343-bcm2835-dma-only-reserve-channel-0-if-legacy-dma-dri.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0344-uapi-bcm2835-isp-Add-bcm2835-isp-uapi-header-file.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0345-staging-vc04_services-ISP-Add-a-more-complex-ISP-pro.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0346-drm-vc4-A-present-but-empty-dmas-disables-audio.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0347-drm-vc4-Add-debugfs-node-that-dumps-the-current-disp.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0348-gpio-Add-gpio-fsm-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0349-drm-vc4-Add-all-the-HDMI-registers-into-the-debugfs-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0350-ARM-dts-bcm271x-Use-a53-pmu-drop-RPI364.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0351-overlays-Add-option-to-disable-composite-to-vc4-kms-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0352-overlays-imx219-Correct-link-frequency-to-match-the-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0353-dts-Add-CM4-to-arm64-dt-files.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0354-drm-vc4-Add-the-2711-HVS-as-a-suitable-DMA-node.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0356-dts-Tidy-the-Raspberry-Pi-Makefile-entries.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0357-staging-bcm2835-audio-Add-disable-headphones-flag.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0358-ARM-dts-Disable-headphone-audio-on-Zeroes-CM4.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0359-overlays-Enable-headphone-audio-in-audremap.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0360-rpisense-fb-Set-pseudo_pallete-to-prevent-crash-on-f.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0361-ARM-dts-Expand-PCIe-space-on-BCM2711.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0362-dwc_otg-Minimise-header-and-fix-build-warnings.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0363-gpio-fsm-Fix-a-build-warning.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0364-rpivid_h625-Fix-build-warnings.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0365-bcm2708_fb-Fix-a-build-warning.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0366-PiFi-40-Devicetree-files.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0367-PiFi-40-driver-Makefile-and-Kconfig.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0368-bcm2835-pcm-Fix-up-multichannel-pcm-audio.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0369-watchdog-bcm2835-Ignore-params-after-the-partition-n.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0370-firmware-raspberrypi-Add-support-for-tryonce-reboot-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0371-phy-broadcom-split-out-the-BCM54213PE-from-the-BCM54.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0372-phy-broadcom-Add-bcm54213pe-configuration.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0373-overlays-Add-MAX31856-support-to-maxtherm-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0374-ARM-dts-Add-bcm2711-rpi-400.dts.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0375-overlays-Deprecate-and-delete-the-sdtweak-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0376-ARM-dts-bcm27xx-Remove-enable_headphones-setting.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0377-vc4_hdmi-Report-that-3d-stereo-is-allowed.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0378-PCI-brcmstb-Restore-initial-fundamental-reset.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0379-vc4-Clear-unused-infoframe-packet-RAM-registers.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0380-Input-edt-ft5x06-Poll-the-device-if-no-interrupt-is-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0381-dtoverlays-Add-an-overlay-for-the-EDT-FT5406-touchsc.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0382-drm-panel-raspberrypi-touchscreen-Use-independent-I2.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0383-drm-panel-raspberrypi-ts-Insert-delay-before-polling.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0384-Add-devicetree-support-for-RaspberryPi-7-panel-over-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0385-mcp251xfd-add-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0386-media-ov9281-Add-1280x720-and-640x480-modes.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0387-dt-bindings-Add-compatible-for-BCM2711-DSI1.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0388-dt-Use-compatible-string-for-BCM2711-DSI1.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0389-drm-vc4-Correct-DSI-register-definition.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0390-Allo-boss2-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0391-Add-allo-boss2-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0392-Overlay-Update-Allo-Piano-Plus-dac-driver-for-5.4.y-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0393-media-bcm2835-unicam-Correctly-handle-error-propagat.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0394-media-bcm2835-unicam-Return-early-from-stop_streamin.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0395-media-bcm2835-unicam-Clear-clock-state-when-stopping.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0396-PCI-brcmstb-Advertise-MSI-X-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0397-ARM-dts-CM4-audio-pins-are-not-connected.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0398-overlays-Add-PCF85063-and-PCF85063A-to-i2c-rtc.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0399-overlays-Fix-cut-and-paste-error-in-README.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0400-staging-bcm2835-codec-Ensure-OUTPUT-timestamps-are-a.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0401-net-lan78xx-Ack-pending-PHY-ints-when-resetting.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0402-overlays-mpu6050-Add-addr-parameter.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0403-drm-vc4-Make-normalize_zpos-conditional-on-using-fkm.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0404-overlays-Add-missing-addresses-to-ads1015-ads1115.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0405-media-i2c-imx477-Selection-compliance-fixes.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0406-staging-vc04_services-codec-Add-support-for-CID-MPEG.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0407-staging-vc04_services-codec-Clear-last-buf-dequeued-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0408-drm-atomic-Pass-the-full-state-to-CRTC-atomic-enable.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0409-drm-atomic-Pass-the-full-state-to-CRTC-atomic_check.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0410-drm-atomic-Pass-the-full-state-to-CRTC-atomic-begin-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0411-drm-vc4-hvs-Align-the-HVS-atomic-hooks-to-the-new-AP.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0412-drm-vc4-Pass-the-atomic-state-to-encoder-hooks.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0413-drm-vc4-hdmi-Don-t-access-the-connector-state-in-res.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0414-drm-vc4-hdmi-Create-a-custom-connector-state.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0415-drm-vc4-hdmi-Store-pixel-frequency-in-the-connector-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0416-drm-vc4-hdmi-Use-the-connector-state-pixel-rate-for-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0417-drm-vc4-hdmi-Enable-10-12-bpc-output.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0418-drm-vc4-Fixup-fkms-for-API-change.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0419-overlays-Rebuild-upstream-with-latest-ovmerge.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0420-Add-overlay-for-Seeed-Studio-CAN-BUS-FD-HAT-4034.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0421-vc-sm-cma-fixed-kbuild-problem.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0422-staging-vc04-services-codec-Fix-logical-precedence-i.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0423-staging-vc04_services-Add-additional-unpacked-raw-fo.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0424-staging-bcm2835-codec-Add-the-unpacked-16bpp-raw-for.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0425-staging-bcm2835-codec-Log-the-number-of-excess-suppo.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0426-staging-bcm2835-isp-Add-the-unpacked-16bpp-raw-forma.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0427-staging-bcm2835-isp-Log-the-number-of-excess-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0428-bcm2835-dma-Add-bcm2835-dma-Add-DMA_WIDE_SOURCE-and-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0429-bcm2835-dma-Move-WAIT_RESP-from-extra-to-info.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0430-bcm2835-dma-Avoid-losing-CS-flags-after-interrupt.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0431-dt-Enable-DMA_WIDE_SOURCE-and-DMA_WIDE_DEST-for-hdmi.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0432-bcm2711-rpi.dtsi-Bump-hdmi-audio-dma-panic-priority-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0433-media-i2c-ov5647-Selection-compliance-fixes.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0434-overlays-give-Seeed-Studio-CAN-BUS-FD-HAT-a-v2-postf.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0435-overlays-Add-overlay-for-Seeed-Studio-CAN-BUS-FD-HAT.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0436-overlays-add-wm8960-soundcard-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0437-overlays-add-spi-override-to-merus-amp-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0438-dt-Add-a-camera-regulator-node-to-all-downstream-Pi-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0439-dtoverlays-Update-sensor-overlays-to-use-cam1_reg-wh.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0440-overlays-seeed-can-fd-hat-clarify-how-to-identify-HA.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0441-SQUASH-Revert-overlays-Make-the-i2c-gpio-overlay-saf.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0442-SQUASH-Revert-overlays-Fix-dtc-warnings-in-i2c-gpio.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0443-uapi-bcm2835-isp-Add-colour-denoise-configuration.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0444-staging-vc04_services-ISP-Add-colour-denoise-control.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0445-dt-bindings-nvmem-Add-bindings-for-rmem-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0446-nvmem-Add-driver-to-expose-reserved-memory-as-nvmem.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0447-ARM-dts-bcm2711-Add-reserved-memory-template-to-hold.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0448-spi-bcm2835-Workaround-fix-for-zero-length-transfers.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0449-kbuild-Silence-unavoidable-dtc-overlay-warnings.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0450-Adds-the-DT-overlays-to-support-Hifiberry-AMP100.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0451-Enhances-the-Hifiberry-DAC-driver-for-Hifiberry-AMP1.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0452-ARM-dts-Declare-Pi400-and-CM4-have-no-audio-pins.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0453-media-i2c-imx290-Replace-V4L2_CID_GAIN-with-V4L2_CID.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0454-media-i2c-imx290-Fix-number-of-controls-in-v4l2_ctrl.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0455-ARM-bcm-Select-BRCMSTB_L2_IRQ-for-bcm2835.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0456-drm-vc4-hdmi-Update-the-CEC-clock-divider-on-HSM-rat.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0457-drm-vc4-hdmi-Introduce-a-CEC-clock.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0458-drm-vc4-hdmi-Split-the-interrupt-handlers.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0459-drm-vc4-hdmi-Support-BCM2711-CEC-interrupt-setup.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0460-drm-vc4-hdmi-Don-t-register-the-CEC-adapter-if-there.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0461-dt-binding-display-bcm2711-hdmi-Add-CEC-and-hotplug-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0462-ARM-dts-bcm2711-Add-the-CEC-interrupt-controller.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0463-bcm2711-Disable-bsc_intr-and-aon_intr-by-default-and.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0464-bcm2711-Remove-old-GIC-interrupt.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0465-staging-bcm2835-camera-Fix-the-cherry-pick-of-AWB-Gr.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0466-Overlays-for-PiFi-Mini-amp.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0467-Added-PiFi-Mini-to-rpi-simple-soundcard.c.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0468-bcm2835-isp-Allow-formats-with-different-colour-spac.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0469-Hifiberry-DAC-ADC-Pro-fix-for-the-PLL-when-changing-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0470-Fixed-picture-line-bug-in-all-ov9281-modes.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0471-Added-hflip-and-vflip-controls-to-ov9281.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0472-gpio-fsm-Rename-num-soft-gpios-to-avoid-warning.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0473-overlays-Rename-gpio-fsm-property-num-soft-gpios.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0474-drm-fix-HDR-static-metadata-type-field-numbering.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0475-drm-vc4-Add-HDR-metadata-property-to-the-VC5-HDMI-co.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0476-drm-vc4-Add-connector-check-to-trigger-mode_change-w.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0477-staging-rpivid-Fix-crash-when-CMA-alloc-fails.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0478-dt-Add-option-for-dpi-without-DE-and-PCLK-for-VGA666.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0479-dtoverlays-Add-an-overlay-for-the-VGA666-when-used-w.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0480-drm-vc4-Change-the-default-DPI-format-to-being-18bpp.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0481-gpio-fsm-Show-state-info-in-sys-class-gpio-fsm.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0482-gpio-fsm-Fix-shutdown-timeout-handling.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0483-overlays-fsm-demo-Ensure-all-LEDs-are-turned-off.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0484-media-i2c-imx477-Remove-auto-frame-length-adjusting.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0485-media-i2c-imx477-Add-very-long-exposure-control-to-t.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0486-media-i2c-imx290-Fix-up-exposure-calcuations-and-ran.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0487-media-i2c-imx290-Handle-exposure-correctly-when-vbla.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0488-DAC-overlays-4154.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0489-media-i2c-imx477-Fix-crop-height-for-2028x1080-mode.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0490-media-i2c-imx477-Replace-existing-1012x760-mode.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0491-media-i2c-imx477-Remove-internal-v4l2_mbus_framefmt-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0492-media-i2c-imx477-Remove-unused-function-parameter.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0493-overlays-i2c-rtc-Add-the-Dallas-DS1340.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0494-overlays-Update-the-upstream-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0495-Revert-Bluetooth-Always-request-for-user-confirmatio.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0496-Revert-Bluetooth-Always-request-for-user-confirmatio.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0497-media-bcm2835-unicam-Fix-bug-in-buffer-swapping-logi.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0498-Assign-crypto-aliases-to-different-AES-implementatio.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0499-overlays-Improve-the-i2c-rtc-i2c_csi_dsi-option.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0500-media-v4l2_m2m-In-buffered-mode-run-jobs-if-either-p.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0501-staging-bcm2835-codec-Correct-logging-of-size_t-to-z.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0502-staging-bcm2835-codec-Add-support-for-pixel-aspect-r.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0503-staging-bcm2835-codec-Implement-additional-g_selecti.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0504-staging-bcm2835-codec-Add-VC-1-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0505-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0506-vc4-drm-Increase-hdmi-audio-axi-priority-to-avoid-lo.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0507-overlays-gpio-led-new-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0508-overlays-Add-pcie-32bit-dma-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0509-ARM-dts-bcm2711-Add-aliases-for-additional-SPIs.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0510-Make-rpi-poe-fan-less-noisy-in-cool-environments.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0511-vc4-drm-Fix-source-offsets-with-DRM_FORMAT_P030.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0512-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0513-clk-raspberrypi-Also-support-HEVC-clock.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0514-dt-Switch-hevc-clock-from-fixed-to-firmware-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0515-rpivid-Request-maximum-hevc-clock.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0516-staging-bcm2835-camera-Add-support-for-DMABUFs.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0517-staging-fbtft-Add-minipitft13-variant.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0518-overlays-Add-minipitft13-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0519-overlays-ghost-amp-Minor-tweaks.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0520-overlays-Add-README-entry-for-minipitft13.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0521-ARM-dts-update-bcm2711-rpi-cm4.dts-and-400.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0522-vc4-drm-SQUASH-Fix-source-offsets-with-DRM_FORMAT_P0.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0523-dwc-otg-fix-clang-Wignored-attributes-warning.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0524-dwc-otg-fix-clang-Wsometimes-uninitialized-warning.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0525-dwc-otg-fix-clang-Wpointer-bool-conversion-warning.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0526-Update-Allo-Piano-Dac-Driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0527-drm-connector-Create-a-helper-to-attach-the-hdr_outp.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0528-drm-connector-Add-helper-to-compare-HDR-metadata.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0529-drm-vc4-Use-the-new-helpers.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0530-drm-connector-Add-a-helper-to-attach-the-colorspace-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0531-drm-vc4-hdmi-Signal-the-proper-colorimetry-info-in-t.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0532-staging-vcsm-cma-Fix-memory-leak-from-not-detaching-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0533-vc4-kms-vc4_plane-Support-2020-colourspace-for-yuv-p.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0534-sound-usb-add-device-quirks-for-A4Tech-FHD-1080p-web.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0535-sound-usb-call-usb_autopm_get_interface-for-devices-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0536-overlays-ghost-amp-Add-DAC-mute-control.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0537-clk-Introduce-a-clock-request-API.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0538-drm-vc4-hdmi-Convert-to-the-new-clock-request-API.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0539-drm-vc4-hdmi-Convert-to-the-new-clock-request-API.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0540-bcm2835-unicam-Switch-to-new-clock-api.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0541-rpivid-Switch-to-new-clock-api.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0542-net-usb-r8152-Provide-missing-documentation-for-some.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0543-net-usb-r8152-Fix-a-couple-of-spelling-errors-in-fw_.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0544-net-usb-r8153_ecm-support-ECM-mode-for-RTL8153.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0545-net-usb-r8152-use-new-tasklet-API.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0546-r8152-replace-several-functions-about-phy-patch-requ.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0547-r8152-adjust-the-flow-of-power-cut-for-RTL8153B.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0548-r8152-enable-U1-U2-for-USB_SPEED_SUPER.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0549-r8152-check-if-the-pointer-of-the-function-exists.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0550-r8152-replace-netif_err-with-dev_err.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0551-r8152-spilt-rtl_set_eee_plus-and-r8153b_green_en.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0552-r8152-set-inter-fram-gap-time-depending-on-speed.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0553-r8152-adjust-rtl8152_check_firmware-function.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0554-r8152-add-help-function-to-change-mtu.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0555-r8152-support-new-chips.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0556-r8152-support-PHY-firmware-for-RTL8156-series.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0557-r8152-search-the-configuration-of-vendor-mode.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0558-rpivid-Only-clk_request_done-once.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0559-dwc_otg-fix-an-undeclared-variable.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0560-drm-vc4-drv-Remove-the-DSI-pointer-in-vc4_drv.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0561-drm-vc4-dsi-Use-snprintf-for-the-PHY-clocks-instead-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0562-drm-vc4-dsi-Introduce-a-variant-structure.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0563-drm-vc4-dsi-Add-support-for-DSI0.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0564-drm-vc4-dsi-Add-configuration-for-BCM2711-DSI1.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0565-drm-vc4-Correct-pixel-order-for-DSI0.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0566-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0567-drm-vc4-Fix-dsi0-interrupt-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0568-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0569-drm-atomic-Don-t-fixup-modes-that-haven-t-been-reset.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0570-drm-panel-jdi-lt070me05000-Use-gpiod_set_value_cansl.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0571-dtoverlays-Add-overlays-for-JDI-LT070ME05000-1200x19.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0572-clk-requests-Ignore-if-the-pointer-is-null.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0573-drm-vc4-hvs-Make-the-HVS-bind-first.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0574-drm-vc4-hdmi-Properly-compute-the-BVB-clock-rate.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0575-drm-vc4-hdmi-Enable-the-scrambler.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0576-drm-vc4-hdmi-Raise-the-maximum-clock-rate.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0577-vc4-drm-hdmi-Handle-case-when-bvb-clock-is-null.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0578-overlays-spi-rtc-Add-ds3232-and-ds3234.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0579-drm-vc4-Fix-VEC-address-for-BCM2711-in-the-devicetre.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0580-drm-vc4-Separate-VEC-compatible-variants.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0581-clk-requests-Dereference-the-request-pointer-after-t.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0582-staging-bcm2835-codec-Fix-support-for-levels-4.1-and.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0583-staging-bcm2835-codec-Set-the-colourspace-appropriat.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0584-staging-bcm2835-codec-Pass-corrupt-frame-flag.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0585-staging-bcm2835-camera-Add-support-for-H264-levels-4.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0586-staging-bcm2835-codec-Do-not-update-crop-from-S_FMT-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0587-staging-bcm2835-isp-Fix-compiler-warning.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0588-overlays-Allow-multiple-gpio-shutdown-instances.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0589-overlays-README-improve-the-gpio-poweroff-guide.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0590-SQUASH-overlays-Fix-typo-in-README.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0591-gpio-poweroff-Remember-the-old-poweroff-handler.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0592-drm-vc4-Allow-DBLCLK-modes-even-if-horz-timing-is-od.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0593-overlays-Add-ugreen-dabboard-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0594-ARM-dts-bcm2711-rpi-400-Limit-MDIO-clock-speed.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0595-spi-bcm2835-Increase-the-CS-limit-to-24.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0596-clk-Always-clamp-the-rounded-rate.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0597-drm-vc4-crtc-Pass-the-drm_atomic_state-to-config_pv.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0598-drm-vc4-crtc-Fix-vc4_get_crtc_encoder-logic.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0599-drm-vc4-crtc-Lookup-the-encoder-from-the-register-at.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0600-drm-vc4-hdmi-Simplify-the-connector-state-retrieval.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0601-drm-vc4-hdmi-Rely-on-interrupts-to-handle-hotplug.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0602-drm-vc4-hdmi-Add-a-workqueue-to-set-scrambling.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0603-vc4-drm-hdmi-Fix-missing-declaration.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0604-overlays-merus-amp-remove-spi-override.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0605-media-i2c-ov5647-Correct-pixel-array-offset.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0606-media-i2c-ov5647-Correct-minimum-VBLANK-value.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0607-media-i2c-ov5647-Fix-v4l2-compliance-failure-subscri.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0608-dtoverlays-Add-pinctrl-names-to-i2c0-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0609-dtoverlays-Update-__symbols__-i2c0-from-i2c0-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0610-media-rpivid-Remove-the-need-to-have-num_entry_point.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0611-media-rpivid-Convert-to-MPLANE.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0612-media-rpivid-Add-an-enable-count-to-irq-claim-Qs.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0613-RFC-media-Add-media_request_-pin-unpin-API.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0614-media-rpivid-Add-a-Pass0-to-accumulate-slices-and-re.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0615-media-rpivid-Map-cmd-buffer-directly.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0616-media-rpivid-Improve-values-returned-when-setting-ou.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0617-media-rpivid-Improve-stream_on-off-conformance-clock.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0618-media-rpivid-Improve-SPS-PPS-error-handling-validati.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0619-overlays-add-sensirion-sgp30-to-i2c-sensor-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0620-overlays-Remove-deleted-merus-amp-parameter.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0621-overlays-add-bh1750-and-ccs811-to-i2c-sensor-4334.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0622-Add-Raspberry-Pi-PoE-HAT-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0623-overlays-Add-rpi-poe-plus-overlay.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0624-drm-vc4-FKMS-Change-of-Broadcast-RGB-mode-needs-a-mo.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0625-overlays-Add-ssd1331-spi-support-for-OLED-screen.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0626-Fixes-an-onboard-clock-detection-problem-of-the-PRO-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0627-bcm2835-Allow-compressed-frames-to-set-sizeimage-438.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0628-media-i2c-imx477-Fix-for-long-exposure-limit-calcula.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0629-overlays-ghost-amp-Change-early-disable-sequence.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0630-drm-vc4-Make-vc4_crtc_get_encoder-public.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0631-ASoC-codec-hdmi-codec-Support-IEC958-encoded-PCM-for.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0632-ASoC-hdmi-codec-Rework-to-support-more-controls.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0633-snd-iec958-split-status-creation-and-fill.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0634-ASoC-hdmi-codec-Add-iec958-controls.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0635-ASoC-hdmi-codec-Add-a-prepare-hook.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0636-drm-vc4-Register-HDMI-codec.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0637-drm-vc4-hdmi-Remove-redundant-variables.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0638-ARM-dts-bcm2711-Tune-DMA-parameters-for-HDMI-audio.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0639-cgroup-Disable-cgroup-memory-by-default.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0640-media-i2c-imx290-Support-60fps-in-2-lane-operation.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0641-media-i2c-imx290-Fix-the-pixel-rate-at-148.5Mpix-s.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0642-media-i2c-imx290-Fix-clock-setup-register-assignment.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0643-drm-vc4-crtc-Add-encoder-to-vc4_crtc_config_pv-proto.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0644-drm-vc4-crtc-Rework-the-encoder-retrieval-code-again.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0645-drm-vc4-crtc-Add-some-logging.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0646-drm-vc4-Leverage-the-load-tracker-on-the-BCM2711.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0647-drm-vc4-Fix-timings-for-interlaced-modes.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0648-drm-vc4-Don-t-create-hvs_load_tracker-on-fkms.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0649-media-rpivid-Fix-H265-aux-ent-reuse-of-the-same-slot.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0650-Support-RPi-DPI-interface-in-mode6-for-18-bit-color.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0651-overlays-Add-dpi18cpadhi-vc4-kms-dpi-at056tn53v1.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0652-drm-vc4-Fix-pixel-wrap-issue-with-DVP-teardown.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0653-media-i2c-ov9281-Remove-override-of-subdev-name.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0654-drm-vc4-hdmi-Use-a-fixed-rate-for-the-HSM-clock-on-B.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0655-drm-vc4-hdmi-Enable-the-scrambler-on-reconnection.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0656-staging-vc04_services-isp-Set-the-YUV420-YVU420-form.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0657-Documentation-devicetree-Add-documentation-for-imx37.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0658-overlays-Add-overlay-for-imx378-sensor.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0659-media-i2c-imx477-Extend-driver-to-support-imx378-sen.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0660-overlays-Make-i2c-rtc-and-i2c-rtc-gpio-share-RTCs.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0661-dt-bindings-clk-raspberrypi-Remove-unused-property.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0662-dt-bindings-display-vc4-Add-phandle-to-the-firmware.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0663-firmware-raspberrypi-Add-RPI_FIRMWARE_NOTIFY_DISPLAY.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0664-drm-vc4-Remove-conflicting-framebuffers-before-calli.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0665-drm-vc4-Notify-the-firmware-when-DRM-is-in-charge.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0666-ARM-dts-rpi-Add-the-firmware-node-to-vc4.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0667-drm-vc4-hdmi-Put-the-device-on-error-in-pre_crtc_con.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0668-drm-vc4-hdmi-Split-the-CEC-disable-enable-functions-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0669-drm-vc4-hdmi-Make-sure-the-device-is-powered-with-CE.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0670-drm-vc4-hdmi-Add-missing-clk_disable_unprepare-on-er.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0671-drm-vc4-hdmi-Warn-if-we-access-the-controller-while-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0672-drm-vc4-hdmi-Move-initial-register-read-after-pm_run.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0673-vc4-drv-Only-notify-firmware-of-display-done-with-km.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0674-dwc_otg-Update-NetBSD-usb.h-header-licence.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0675-drm-vc4-hdmi-Drop-devm-interrupt-handler-for-CEC-int.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0676-drm-vc4-hdmi-Drop-devm-interrupt-handler-for-hotplug.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0677-drm-vc4-hdmi-Only-call-into-DRM-framework-if-registe.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0678-bcm2711_thermal-Don-t-clamp-temperature-at-zero.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0679-media-bcm2835-unicam-Forward-input-status-from-subde.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0680-overlays-Add-overlay-for-Chipdip-I2S-master-DAC.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0681-drm-Introduce-an-atomic_commit_setup-function.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0682-drm-Document-use-after-free-gotcha-with-private-obje.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0683-drm-vc4-Simplify-a-bit-the-global-atomic_check.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0684-drm-vc4-hdmi-Don-t-poll-for-the-infoframes-status-on.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0685-drm-vc4-hvs-Align-the-HVS-atomic-hooks-to-the-new-AP.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0686-drm-Use-the-state-pointer-directly-in-atomic_check.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0687-drm-vc4-Remove-unnecessary-drm_plane_cleanup-wrapper.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0688-drm-vc4-plane-Remove-redundant-assignment.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0689-drm-automatic-legacy-gamma-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0690-drm-Pass-the-full-state-to-connectors-atomic-functio.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0691-drm-vc4-replace-idr_init-by-idr_init_base.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0692-drm-vc4-vc4_hdmi_regs-Mark-some-data-sets-as-__maybe.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0693-drm-vc4-remove-unneeded-variable-ret.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0694-overlays-Add-overlay-for-cap1106-capacitive-touch-se.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0695-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0696-ydrm-vc4-fkms-Fix-margin-calculations-for-the-right-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0697-ARM-dts-bcm2711-fold-in-the-correct-interrupt.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0698-overlays-Add-overlay-for-Si446x-Transceiver-SPI.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0699-drm-vc4-Fix-timings-for-VEC-modes.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0700-drm-vc4-Refactor-VEC-TV-mode-setting.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0701-drm-vc4-Fix-definition-of-PAL-M-mode.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0702-drm-vc4-Add-support-for-more-analog-TV-standards.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0703-drm-vc4-Allow-setting-the-TV-norm-via-module-paramet.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0704-drm-vc4-Refactor-mode-checking-logic.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0705-drm-vc4-Fix-typo-when-getting-firmware-node.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0706-ARM-dts-bcm2711-Tidy-the-HDMI-I2C-aliases.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0707-media-i2c-imx477-Fix-framerates-for-1332x990-mode.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0708-drm-uapi-Add-USB-connector-type.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0709-drm-Add-GUD-USB-Display-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0710-drm-gud-fix-sizeof-use.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0711-drm-gud-Remove-unneeded-semicolon.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0712-drm-gud-cleanup-coding-style-a-bit.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0713-drm-gud-Free-buffers-on-device-removal.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0714-drm-gud-Use-scatter-gather-USB-bulk-transfer.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0715-drm-gud-Add-Raspberry-Pi-Pico-ID.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0716-drm-gud-Add-async_flush-module-parameter.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0717-drm-vc4-hdmi-Make-sure-the-controller-is-powered-up-.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0718-overlays-Set-CMA-to-512MB-on-Pi-4-for-vc4.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0719-ARM-dts-Correct-CM4-PHY-MDIO-address.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0720-drm-vc4-Increase-the-core-clock-based-on-HVS-load.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0721-drm-vc4-Increase-the-core-clock-to-a-minimum-of-500M.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0722-overlays-Update-and-rename-chipdip-i2s-master-dac.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0723-ASoC-bcm-Add-chipdip-dac-driver.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0724-char-vc_mem-Delete-dead-code.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0725-overlays-Add-Ablic-S35390A-to-i2c-rtc-and-gpio.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0726-dtoverlays-Add-orientation-and-rotation-parameter-to.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0727-media-i2c-imx290-Add-fwnode-properties-controls.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0728-media-i2c-ov9281-Add-fwnode-properties-controls.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0729-media-i2c-ov7251-Add-fwnode-properties-controls.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0730-overlays-Reduce-Pi-4-vc4-CMA-size-to-320MB.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0731-Revert-overlays-Update-display-GPIO-declarations-for.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0732-overlays-Add-midi-uart-2345-overlay.dts.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0733-usb-xhci-workaround-for-bogus-SET_DEQ_PENDING-endpoi.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0734-overlays-Add-TI-BQ32000-RTC-support.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0735-xhci-guard-accesses-to-ep_state-in-xhci_endpoint_res.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0736-ARM-dts-Adapt-to-upstream-changes.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0737-overlays-rpi-poe-plus-Improve-the-cooling-levels.patch create mode 100644 target/linux/bcm27xx/patches-5.10/950-0738-Makefiles-dt-Always-set-on-ARCH_BCM2835.patch create mode 100644 target/linux/bcm27xx/patches-5.10/960-hwrng-iproc-set-quality-to-1000.patch diff --git a/target/linux/bcm27xx/bcm2708/config-5.10 b/target/linux/bcm27xx/bcm2708/config-5.10 new file mode 100644 index 0000000000..094765abdc --- /dev/null +++ b/target/linux/bcm27xx/bcm2708/config-5.10 @@ -0,0 +1,366 @@ +# CONFIG_AIO is not set +CONFIG_ALIGNMENT_TRAP=y +CONFIG_ARCH_32BIT_OFF_T=y +CONFIG_ARCH_BCM=y +CONFIG_ARCH_BCM2835=y +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +CONFIG_ARCH_KEEP_MEMBLOCK=y +CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y +CONFIG_ARCH_MULTIPLATFORM=y +CONFIG_ARCH_MULTI_V6=y +CONFIG_ARCH_MULTI_V6_V7=y +CONFIG_ARCH_NR_GPIO=0 +CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y +CONFIG_ARCH_SELECT_MEMORY_MODEL=y +CONFIG_ARCH_SPARSEMEM_ENABLE=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARM=y +CONFIG_ARM_AMBA=y +CONFIG_ARM_CPU_SUSPEND=y +CONFIG_ARM_ERRATA_411920=y +CONFIG_ARM_HAS_SG_CHAIN=y +CONFIG_ARM_L1_CACHE_SHIFT=5 +CONFIG_ARM_PATCH_PHYS_VIRT=y +CONFIG_ARM_RASPBERRYPI_CPUFREQ=y +CONFIG_ARM_THUMB=y +CONFIG_ARM_TIMER_SP804=y +CONFIG_ARM_UNWIND=y +CONFIG_AUTO_ZRELADDR=y +CONFIG_BCM2708_VCMEM=y +# CONFIG_BCM2711_THERMAL is not set +CONFIG_BCM2835_DEVGPIOMEM=y +CONFIG_BCM2835_FAST_MEMCPY=y +CONFIG_BCM2835_MBOX=y +CONFIG_BCM2835_POWER=y +# CONFIG_BCM2835_SMI is not set +CONFIG_BCM2835_THERMAL=y +CONFIG_BCM2835_TIMER=y +CONFIG_BCM2835_VCHIQ=y +# CONFIG_BCM2835_VCHIQ_MMAL is not set +CONFIG_BCM2835_WDT=y +CONFIG_BCM_VCIO=y +# CONFIG_BCM_VC_SM_CMA is not set +CONFIG_BCM_VIDEOCORE=y +CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y +# CONFIG_BLK_DEV_INITRD is not set +CONFIG_BLK_DEV_LOOP=y +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +CONFIG_BLK_DEV_SD=y +CONFIG_BLK_PM=y +CONFIG_BLK_SCSI_REQUEST=y +CONFIG_BRCMSTB_L2_IRQ=y +CONFIG_BRCM_CHAR_DRIVERS=y +# CONFIG_CACHE_L2X0 is not set +CONFIG_CLKDEV_LOOKUP=y +CONFIG_CLKSRC_MMIO=y +CONFIG_CLK_BCM2711_DVP=y +CONFIG_CLK_BCM2835=y +CONFIG_CLK_RASPBERRYPI=y +CONFIG_CLONE_BACKWARDS=y +CONFIG_CMA=y +CONFIG_CMA_ALIGNMENT=8 +CONFIG_CMA_AREAS=7 +# CONFIG_CMA_DEBUG is not set +# CONFIG_CMA_DEBUGFS is not set +CONFIG_CMA_SIZE_MBYTES=5 +# CONFIG_CMA_SIZE_SEL_MAX is not set +CONFIG_CMA_SIZE_SEL_MBYTES=y +# CONFIG_CMA_SIZE_SEL_MIN is not set +# CONFIG_CMA_SIZE_SEL_PERCENTAGE is not set +CONFIG_COMMON_CLK=y +CONFIG_COMPAT_32BIT_TIME=y +CONFIG_CONFIGFS_FS=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_CONTIG_ALLOC=y +CONFIG_CPUFREQ_DT=y +CONFIG_CPUFREQ_DT_PLATDEV=y +CONFIG_CPU_32v6=y +CONFIG_CPU_32v6K=y +CONFIG_CPU_ABRT_EV6=y +CONFIG_CPU_CACHE_V6=y +CONFIG_CPU_CACHE_VIPT=y +CONFIG_CPU_COPY_V6=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y +CONFIG_CPU_FREQ=y +CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y +# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set +CONFIG_CPU_FREQ_GOV_ATTR_SET=y +CONFIG_CPU_FREQ_GOV_COMMON=y +CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y +CONFIG_CPU_FREQ_GOV_ONDEMAND=y +CONFIG_CPU_FREQ_GOV_PERFORMANCE=y +CONFIG_CPU_FREQ_GOV_POWERSAVE=y +CONFIG_CPU_FREQ_GOV_USERSPACE=y +CONFIG_CPU_FREQ_STAT=y +CONFIG_CPU_HAS_ASID=y +CONFIG_CPU_IDLE=y +CONFIG_CPU_IDLE_GOV_LADDER=y +CONFIG_CPU_IDLE_GOV_MENU=y +CONFIG_CPU_PABRT_V6=y +CONFIG_CPU_PM=y +CONFIG_CPU_THUMB_CAPABLE=y +CONFIG_CPU_TLB_V6=y +CONFIG_CPU_V6K=y +CONFIG_CRC16=y +CONFIG_CRYPTO_CRC32=y +CONFIG_CRYPTO_CRC32C=y +CONFIG_CRYPTO_GF128MUL=y +CONFIG_CRYPTO_NULL2=y +CONFIG_CRYPTO_RNG2=y +CONFIG_DCACHE_WORD_ACCESS=y +CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_DEBUG_INFO=y +CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S" +CONFIG_DMABUF_HEAPS=y +CONFIG_DMABUF_HEAPS_CMA=y +CONFIG_DMABUF_HEAPS_SYSTEM=y +CONFIG_DMADEVICES=y +CONFIG_DMA_BCM2708=y +CONFIG_DMA_BCM2835=y +CONFIG_DMA_CMA=y +CONFIG_DMA_ENGINE=y +CONFIG_DMA_OF=y +CONFIG_DMA_OPS=y +CONFIG_DMA_REMAP=y +CONFIG_DMA_SHARED_BUFFER=y +CONFIG_DMA_VIRTUAL_CHANNELS=y +CONFIG_DNOTIFY=y +CONFIG_DTC=y +CONFIG_DUMMY_CONSOLE=y +CONFIG_EDAC_ATOMIC_SCRUB=y +CONFIG_EDAC_SUPPORT=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_EXT4_FS=y +CONFIG_EXT4_FS_POSIX_ACL=y +CONFIG_EXT4_FS_SECURITY=y +CONFIG_F2FS_FS=y +CONFIG_FB=y +CONFIG_FB_BCM2708=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_IMAGEBLIT=y +CONFIG_FB_CMDLINE=y +# CONFIG_FB_RPISENSE is not set +CONFIG_FB_SIMPLE=y +CONFIG_FIQ=y +CONFIG_FIXED_PHY=y +CONFIG_FIX_EARLYCON_MEM=y +CONFIG_FONT_8x16=y +CONFIG_FONT_8x8=y +CONFIG_FONT_SUPPORT=y +# CONFIG_FPE_FASTFPE is not set +# CONFIG_FPE_NWFPE is not set +CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set +CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y +CONFIG_FREEZER=y +CONFIG_FS_IOMAP=y +CONFIG_FS_MBCACHE=y +CONFIG_FS_POSIX_ACL=y +CONFIG_FW_CACHE=y +CONFIG_FW_LOADER_PAGED_BUF=y +CONFIG_GENERIC_ALLOCATOR=y +CONFIG_GENERIC_BUG=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CPU_AUTOPROBE=y +CONFIG_GENERIC_EARLY_IOREMAP=y +CONFIG_GENERIC_IDLE_POLL_SETUP=y +CONFIG_GENERIC_IRQ_CHIP=y +CONFIG_GENERIC_IRQ_MULTI_HANDLER=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_IRQ_SHOW_LEVEL=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_PINCONF=y +CONFIG_GENERIC_PINCTRL_GROUPS=y +CONFIG_GENERIC_PINMUX_FUNCTIONS=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_STRNCPY_FROM_USER=y +CONFIG_GENERIC_STRNLEN_USER=y +CONFIG_GPIOLIB=y +CONFIG_GPIOLIB_IRQCHIP=y +# CONFIG_GPIO_BCM_VIRT is not set +# CONFIG_GPIO_FSM is not set +CONFIG_GPIO_RASPBERRYPI_EXP=y +CONFIG_HANDLE_DOMAIN_IRQ=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT_MAP=y +CONFIG_HW_CONSOLE=y +CONFIG_HW_RANDOM=y +CONFIG_HW_RANDOM_BCM2835=y +CONFIG_HZ_FIXED=0 +CONFIG_I2C=y +# CONFIG_I2C_BCM2708 is not set +CONFIG_I2C_BOARDINFO=y +# CONFIG_I2C_BRCMSTB is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_INPUT=y +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +CONFIG_IRQCHIP=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_WORK=y +CONFIG_JBD2=y +CONFIG_KERNEL_GZIP=y +# CONFIG_KERNEL_XZ is not set +CONFIG_LEDS_GPIO=y +CONFIG_LEDS_TRIGGER_ACTPWR=y +CONFIG_LEDS_TRIGGER_INPUT=y +CONFIG_LIBFDT=y +CONFIG_LLD_VERSION=0 +CONFIG_LOCK_DEBUGGING_SUPPORT=y +CONFIG_LOGO=y +CONFIG_LOGO_LINUX_CLUT224=y +# CONFIG_LOGO_LINUX_MONO is not set +# CONFIG_LOGO_LINUX_VGA16 is not set +CONFIG_MAC_PARTITION=y +CONFIG_MAGIC_SYSRQ=y +CONFIG_MAILBOX=y +# CONFIG_MAILBOX_TEST is not set +CONFIG_MAX_RAW_DEVS=256 +CONFIG_MDIO_BUS=y +CONFIG_MDIO_DEVICE=y +CONFIG_MDIO_DEVRES=y +CONFIG_MEMFD_CREATE=y +CONFIG_MEMORY_ISOLATION=y +CONFIG_MFD_CORE=y +# CONFIG_MFD_RPISENSE_CORE is not set +CONFIG_MFD_SYSCON=y +CONFIG_MIGHT_HAVE_CACHE_L2X0=y +CONFIG_MIGRATION=y +CONFIG_MMC=y +CONFIG_MMC_BCM2835=y +CONFIG_MMC_BCM2835_DMA=y +CONFIG_MMC_BCM2835_MMC=y +CONFIG_MMC_BCM2835_PIO_DMA_BARRIER=2 +CONFIG_MMC_BCM2835_SDHOST=y +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_MINORS=32 +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_PLTFM=y +CONFIG_MODULES_USE_ELF_REL=y +# CONFIG_MTD is not set +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NEED_PER_CPU_KM=y +CONFIG_NLS=y +CONFIG_NLS_ASCII=y +CONFIG_NO_HZ=y +CONFIG_NO_HZ_COMMON=y +CONFIG_NO_HZ_IDLE=y +CONFIG_NVMEM=y +# CONFIG_NVMEM_RMEM is not set +CONFIG_OABI_COMPAT=y +CONFIG_OF=y +CONFIG_OF_ADDRESS=y +CONFIG_OF_CONFIGFS=y +CONFIG_OF_DYNAMIC=y +CONFIG_OF_EARLY_FLATTREE=y +CONFIG_OF_FLATTREE=y +CONFIG_OF_GPIO=y +CONFIG_OF_IRQ=y +CONFIG_OF_KOBJ=y +CONFIG_OF_MDIO=y +CONFIG_OF_NET=y +CONFIG_OF_OVERLAY=y +CONFIG_OF_RESOLVE=y +CONFIG_OLD_SIGACTION=y +CONFIG_OLD_SIGSUSPEND3=y +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PGTABLE_LEVELS=2 +CONFIG_PHYLIB=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_BCM2835=y +CONFIG_PM=y +CONFIG_PM_CLK=y +CONFIG_PM_GENERIC_DOMAINS=y +CONFIG_PM_GENERIC_DOMAINS_OF=y +CONFIG_PM_GENERIC_DOMAINS_SLEEP=y +CONFIG_PM_OPP=y +CONFIG_PM_SLEEP=y +CONFIG_POWER_SUPPLY=y +CONFIG_PRINTK_TIME=y +CONFIG_RASPBERRYPI_FIRMWARE=y +CONFIG_RASPBERRYPI_POWER=y +CONFIG_RATIONAL=y +# CONFIG_RAVE_SP_CORE is not set +CONFIG_RAW_DRIVER=y +CONFIG_REGMAP=y +CONFIG_REGMAP_MMIO=y +CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y +CONFIG_RESET_CONTROLLER=y +# CONFIG_RESET_RASPBERRYPI is not set +CONFIG_RESET_SIMPLE=y +# CONFIG_RPIVID_MEM is not set +# CONFIG_RPI_POE_POWER is not set +CONFIG_SCSI=y +# CONFIG_SCSI_LOWLEVEL is not set +# CONFIG_SCSI_PROC_FS is not set +CONFIG_SERIAL_8250_BCM2835AUX=y +# CONFIG_SERIAL_8250_DMA is not set +CONFIG_SERIAL_8250_EXTENDED=y +CONFIG_SERIAL_8250_FSL=y +CONFIG_SERIAL_8250_NR_UARTS=1 +CONFIG_SERIAL_8250_RUNTIME_UARTS=0 +CONFIG_SERIAL_8250_SHARE_IRQ=y +CONFIG_SERIAL_AMBA_PL011=y +CONFIG_SERIAL_AMBA_PL011_CONSOLE=y +CONFIG_SERIAL_DEV_BUS=y +# CONFIG_SERIAL_DEV_CTRL_TTYPORT is not set +CONFIG_SERIAL_MCTRL_GPIO=y +CONFIG_SERIAL_OF_PLATFORM=y +CONFIG_SG_POOL=y +CONFIG_SMSC_PHY=y +CONFIG_SPARSE_IRQ=y +CONFIG_SRCU=y +# CONFIG_STRIP_ASM_SYMS is not set +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y +CONFIG_SWPHY=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +# CONFIG_TEXTSEARCH is not set +CONFIG_THERMAL=y +CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y +CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0 +CONFIG_THERMAL_GOV_STEP_WISE=y +CONFIG_THERMAL_OF=y +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_TIMER_OF=y +CONFIG_TIMER_PROBE=y +CONFIG_TINY_SRCU=y +CONFIG_TMPFS_POSIX_ACL=y +CONFIG_UEVENT_HELPER_PATH="" +# CONFIG_UID16 is not set +CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h" +CONFIG_UNWINDER_ARM=y +CONFIG_USB=y +CONFIG_USB_ANNOUNCE_NEW_DEVICES=y +CONFIG_USB_COMMON=y +CONFIG_USB_DWCOTG=y +CONFIG_USB_NET_DRIVERS=y +CONFIG_USB_NET_SMSC95XX=y +CONFIG_USB_STORAGE=y +CONFIG_USB_SUPPORT=y +CONFIG_USB_UAS=y +CONFIG_USB_USBNET=y +CONFIG_USE_OF=y +CONFIG_VFP=y +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_VT_CONSOLE_SLEEP=y +CONFIG_VT_HW_CONSOLE_BINDING=y +CONFIG_WATCHDOG_CORE=y +CONFIG_XZ_DEC_ARM=y +CONFIG_XZ_DEC_BCJ=y +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_ZBOOT_ROM_TEXT=0x0 diff --git a/target/linux/bcm27xx/bcm2709/config-5.10 b/target/linux/bcm27xx/bcm2709/config-5.10 new file mode 100644 index 0000000000..a04ee1ddd9 --- /dev/null +++ b/target/linux/bcm27xx/bcm2709/config-5.10 @@ -0,0 +1,464 @@ +# CONFIG_AIO is not set +CONFIG_ALIGNMENT_TRAP=y +CONFIG_ARCH_32BIT_OFF_T=y +CONFIG_ARCH_BCM=y +CONFIG_ARCH_BCM2835=y +# CONFIG_ARCH_BCM_HR2 is not set +CONFIG_ARCH_DMA_ADDR_T_64BIT=y +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +CONFIG_ARCH_KEEP_MEMBLOCK=y +CONFIG_ARCH_MIGHT_HAVE_PC_PARPORT=y +CONFIG_ARCH_MULTIPLATFORM=y +CONFIG_ARCH_MULTI_V6_V7=y +CONFIG_ARCH_MULTI_V7=y +CONFIG_ARCH_NR_GPIO=0 +CONFIG_ARCH_OPTIONAL_KERNEL_RWX=y +CONFIG_ARCH_OPTIONAL_KERNEL_RWX_DEFAULT=y +CONFIG_ARCH_SELECT_MEMORY_MODEL=y +CONFIG_ARCH_SPARSEMEM_ENABLE=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARM=y +CONFIG_ARM_AMBA=y +CONFIG_ARM_ARCH_TIMER=y +CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y +CONFIG_ARM_CPU_SUSPEND=y +CONFIG_ARM_GIC=y +CONFIG_ARM_HAS_SG_CHAIN=y +CONFIG_ARM_L1_CACHE_SHIFT=6 +CONFIG_ARM_L1_CACHE_SHIFT_6=y +CONFIG_ARM_LPAE=y +CONFIG_ARM_PATCH_IDIV=y +CONFIG_ARM_PATCH_PHYS_VIRT=y +CONFIG_ARM_RASPBERRYPI_CPUFREQ=y +CONFIG_ARM_THUMB=y +CONFIG_ARM_TIMER_SP804=y +CONFIG_ARM_UNWIND=y +CONFIG_ARM_VIRT_EXT=y +CONFIG_ASSOCIATIVE_ARRAY=y +CONFIG_AUTO_ZRELADDR=y +CONFIG_BCM2708_VCMEM=y +CONFIG_BCM2711_THERMAL=y +CONFIG_BCM2835_DEVGPIOMEM=y +CONFIG_BCM2835_MBOX=y +CONFIG_BCM2835_POWER=y +# CONFIG_BCM2835_SMI is not set +CONFIG_BCM2835_THERMAL=y +CONFIG_BCM2835_TIMER=y +CONFIG_BCM2835_VCHIQ=y +# CONFIG_BCM2835_VCHIQ_MMAL is not set +CONFIG_BCM2835_WDT=y +CONFIG_BCM7XXX_PHY=y +CONFIG_BCMGENET=y +CONFIG_BCM_NET_PHYLIB=y +CONFIG_BCM_VCIO=y +# CONFIG_BCM_VC_SM_CMA is not set +CONFIG_BCM_VIDEOCORE=y +CONFIG_BINFMT_FLAT_ARGVP_ENVP_ON_STACK=y +# CONFIG_BLK_DEV_INITRD is not set +CONFIG_BLK_DEV_LOOP=y +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +CONFIG_BLK_DEV_SD=y +CONFIG_BLK_MQ_PCI=y +CONFIG_BLK_PM=y +CONFIG_BLK_SCSI_REQUEST=y +CONFIG_BOUNCE=y +CONFIG_BRCMSTB_L2_IRQ=y +CONFIG_BRCM_CHAR_DRIVERS=y +CONFIG_BROADCOM_PHY=y +# CONFIG_CACHE_L2X0 is not set +CONFIG_CLKDEV_LOOKUP=y +CONFIG_CLKSRC_MMIO=y +CONFIG_CLK_BCM2711_DVP=y +CONFIG_CLK_BCM2835=y +CONFIG_CLK_RASPBERRYPI=y +CONFIG_CLONE_BACKWARDS=y +CONFIG_CMA=y +CONFIG_CMA_ALIGNMENT=8 +CONFIG_CMA_AREAS=7 +# CONFIG_CMA_DEBUG is not set +# CONFIG_CMA_DEBUGFS is not set +CONFIG_CMA_SIZE_MBYTES=5 +# CONFIG_CMA_SIZE_SEL_MAX is not set +CONFIG_CMA_SIZE_SEL_MBYTES=y +# CONFIG_CMA_SIZE_SEL_MIN is not set +# CONFIG_CMA_SIZE_SEL_PERCENTAGE is not set +CONFIG_COMMON_CLK=y +CONFIG_COMPAT_32BIT_TIME=y +CONFIG_CONFIGFS_FS=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_CONTIG_ALLOC=y +CONFIG_CPUFREQ_DT=y +CONFIG_CPUFREQ_DT_PLATDEV=y +CONFIG_CPU_32v6K=y +CONFIG_CPU_32v7=y +CONFIG_CPU_ABRT_EV7=y +CONFIG_CPU_CACHE_V7=y +CONFIG_CPU_CACHE_VIPT=y +CONFIG_CPU_COPY_V6=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y +CONFIG_CPU_FREQ=y +CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y +# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set +CONFIG_CPU_FREQ_GOV_ATTR_SET=y +CONFIG_CPU_FREQ_GOV_COMMON=y +CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y +CONFIG_CPU_FREQ_GOV_ONDEMAND=y +CONFIG_CPU_FREQ_GOV_PERFORMANCE=y +CONFIG_CPU_FREQ_GOV_POWERSAVE=y +CONFIG_CPU_FREQ_GOV_USERSPACE=y +CONFIG_CPU_FREQ_STAT=y +CONFIG_CPU_HAS_ASID=y +CONFIG_CPU_IDLE=y +CONFIG_CPU_IDLE_GOV_LADDER=y +CONFIG_CPU_IDLE_GOV_MENU=y +CONFIG_CPU_PABRT_V7=y +CONFIG_CPU_PM=y +CONFIG_CPU_RMAP=y +CONFIG_CPU_SPECTRE=y +CONFIG_CPU_THUMB_CAPABLE=y +CONFIG_CPU_TLB_V7=y +CONFIG_CPU_V7=y +CONFIG_CRC16=y +CONFIG_CRYPTO_CBC=y +CONFIG_CRYPTO_CRC32=y +CONFIG_CRYPTO_CRC32C=y +CONFIG_CRYPTO_CTS=y +CONFIG_CRYPTO_DRBG=y +CONFIG_CRYPTO_DRBG_HMAC=y +CONFIG_CRYPTO_DRBG_MENU=y +CONFIG_CRYPTO_ECB=y +CONFIG_CRYPTO_GF128MUL=y +CONFIG_CRYPTO_HMAC=y +CONFIG_CRYPTO_JITTERENTROPY=y +CONFIG_CRYPTO_LIB_SHA256=y +CONFIG_CRYPTO_NULL2=y +CONFIG_CRYPTO_RNG=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_RNG_DEFAULT=y +CONFIG_CRYPTO_SEQIV=y +CONFIG_CRYPTO_SHA256=y +CONFIG_CRYPTO_SHA512=y +CONFIG_CRYPTO_XTS=y +CONFIG_DCACHE_WORD_ACCESS=y +CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_DEBUG_INFO=y +CONFIG_DEBUG_LL_INCLUDE="mach/debug-macro.S" +CONFIG_DIMLIB=y +CONFIG_DMABUF_HEAPS=y +CONFIG_DMABUF_HEAPS_CMA=y +CONFIG_DMABUF_HEAPS_SYSTEM=y +CONFIG_DMADEVICES=y +CONFIG_DMA_BCM2708=y +CONFIG_DMA_BCM2835=y +CONFIG_DMA_CMA=y +CONFIG_DMA_ENGINE=y +CONFIG_DMA_OF=y +CONFIG_DMA_OPS=y +CONFIG_DMA_REMAP=y +CONFIG_DMA_SHARED_BUFFER=y +CONFIG_DMA_VIRTUAL_CHANNELS=y +CONFIG_DNOTIFY=y +CONFIG_DTC=y +CONFIG_DUMMY_CONSOLE=y +CONFIG_EDAC_ATOMIC_SCRUB=y +CONFIG_EDAC_SUPPORT=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_EXT4_FS=y +CONFIG_EXT4_FS_POSIX_ACL=y +CONFIG_EXT4_FS_SECURITY=y +CONFIG_EXTCON=y +CONFIG_F2FS_FS=y +CONFIG_FB=y +CONFIG_FB_BCM2708=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_IMAGEBLIT=y +CONFIG_FB_CMDLINE=y +# CONFIG_FB_RPISENSE is not set +CONFIG_FB_SIMPLE=y +CONFIG_FIQ=y +CONFIG_FIXED_PHY=y +CONFIG_FIX_EARLYCON_MEM=y +CONFIG_FONT_8x16=y +CONFIG_FONT_8x8=y +CONFIG_FONT_SUPPORT=y +# CONFIG_FPE_FASTFPE is not set +# CONFIG_FPE_NWFPE is not set +CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set +CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y +CONFIG_FREEZER=y +CONFIG_FS_ENCRYPTION=y +CONFIG_FS_ENCRYPTION_ALGS=y +CONFIG_FS_IOMAP=y +CONFIG_FS_MBCACHE=y +CONFIG_FS_POSIX_ACL=y +CONFIG_FW_CACHE=y +CONFIG_FW_LOADER_PAGED_BUF=y +CONFIG_GENERIC_ALLOCATOR=y +CONFIG_GENERIC_ARCH_TOPOLOGY=y +CONFIG_GENERIC_BUG=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y +CONFIG_GENERIC_CPU_AUTOPROBE=y +CONFIG_GENERIC_EARLY_IOREMAP=y +CONFIG_GENERIC_GETTIMEOFDAY=y +CONFIG_GENERIC_IDLE_POLL_SETUP=y +CONFIG_GENERIC_IRQ_CHIP=y +CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y +CONFIG_GENERIC_IRQ_MIGRATION=y +CONFIG_GENERIC_IRQ_MULTI_HANDLER=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_IRQ_SHOW_LEVEL=y +CONFIG_GENERIC_MSI_IRQ=y +CONFIG_GENERIC_MSI_IRQ_DOMAIN=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_PHY=y +CONFIG_GENERIC_PINCONF=y +CONFIG_GENERIC_PINCTRL_GROUPS=y +CONFIG_GENERIC_PINMUX_FUNCTIONS=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_STRNCPY_FROM_USER=y +CONFIG_GENERIC_STRNLEN_USER=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GENERIC_VDSO_32=y +CONFIG_GPIOLIB=y +CONFIG_GPIOLIB_IRQCHIP=y +CONFIG_GPIO_BCM_VIRT=y +# CONFIG_GPIO_FSM is not set +CONFIG_GPIO_RASPBERRYPI_EXP=y +CONFIG_HANDLE_DOMAIN_IRQ=y +CONFIG_HARDEN_BRANCH_PREDICTOR=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT_MAP=y +CONFIG_HAVE_SMP=y +CONFIG_HIGHMEM=y +CONFIG_HIGHPTE=y +CONFIG_HOTPLUG_CPU=y +CONFIG_HW_CONSOLE=y +CONFIG_HW_RANDOM=y +CONFIG_HW_RANDOM_BCM2835=y +CONFIG_HW_RANDOM_IPROC_RNG200=y +CONFIG_HZ_FIXED=0 +CONFIG_I2C=y +# CONFIG_I2C_BCM2708 is not set +CONFIG_I2C_BOARDINFO=y +# CONFIG_I2C_BRCMSTB is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_INPUT=y +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +CONFIG_IRQCHIP=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_DOMAIN_HIERARCHY=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_WORK=y +CONFIG_JBD2=y +CONFIG_KEYS=y +CONFIG_LEDS_GPIO=y +CONFIG_LEDS_TRIGGER_ACTPWR=y +CONFIG_LEDS_TRIGGER_INPUT=y +CONFIG_LIBFDT=y +CONFIG_LLD_VERSION=0 +CONFIG_LOCK_DEBUGGING_SUPPORT=y +CONFIG_LOCK_SPIN_ON_OWNER=y +CONFIG_LOGO=y +CONFIG_LOGO_LINUX_CLUT224=y +# CONFIG_LOGO_LINUX_MONO is not set +# CONFIG_LOGO_LINUX_VGA16 is not set +CONFIG_MAC_PARTITION=y +CONFIG_MAGIC_SYSRQ=y +CONFIG_MAILBOX=y +# CONFIG_MAILBOX_TEST is not set +CONFIG_MAX_RAW_DEVS=256 +CONFIG_MDIO_BCM_UNIMAC=y +CONFIG_MDIO_BUS=y +CONFIG_MDIO_DEVICE=y +CONFIG_MDIO_DEVRES=y +CONFIG_MEMFD_CREATE=y +CONFIG_MEMORY_ISOLATION=y +CONFIG_MFD_CORE=y +# CONFIG_MFD_RPISENSE_CORE is not set +CONFIG_MFD_SYSCON=y +CONFIG_MICROCHIP_PHY=y +CONFIG_MIGHT_HAVE_CACHE_L2X0=y +CONFIG_MIGRATION=y +CONFIG_MMC=y +CONFIG_MMC_BCM2835=y +CONFIG_MMC_BCM2835_DMA=y +CONFIG_MMC_BCM2835_MMC=y +CONFIG_MMC_BCM2835_PIO_DMA_BARRIER=2 +CONFIG_MMC_BCM2835_SDHOST=y +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_MINORS=32 +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_IO_ACCESSORS=y +CONFIG_MMC_SDHCI_IPROC=y +# CONFIG_MMC_SDHCI_PCI is not set +CONFIG_MMC_SDHCI_PLTFM=y +CONFIG_MODULES_USE_ELF_REL=y +# CONFIG_MTD is not set +CONFIG_MUTEX_SPIN_ON_OWNER=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NEON=y +CONFIG_NET_FLOW_LIMIT=y +CONFIG_NLS=y +CONFIG_NLS_ASCII=y +CONFIG_NOP_USB_XCEIV=y +CONFIG_NO_HZ=y +CONFIG_NO_HZ_COMMON=y +CONFIG_NO_HZ_IDLE=y +CONFIG_NR_CPUS=4 +CONFIG_NVMEM=y +# CONFIG_NVMEM_RMEM is not set +CONFIG_OABI_COMPAT=y +CONFIG_OF=y +CONFIG_OF_ADDRESS=y +CONFIG_OF_CONFIGFS=y +CONFIG_OF_DYNAMIC=y +CONFIG_OF_EARLY_FLATTREE=y +CONFIG_OF_FLATTREE=y +CONFIG_OF_GPIO=y +CONFIG_OF_IRQ=y +CONFIG_OF_KOBJ=y +CONFIG_OF_MDIO=y +CONFIG_OF_NET=y +CONFIG_OF_OVERLAY=y +CONFIG_OF_RESOLVE=y +CONFIG_OLD_SIGACTION=y +CONFIG_OLD_SIGSUSPEND3=y +CONFIG_PADATA=y +CONFIG_PAGE_OFFSET=0xC0000000 +CONFIG_PCI=y +CONFIG_PCIEAER=y +CONFIG_PCIEPORTBUS=y +CONFIG_PCIE_BRCMSTB=y +CONFIG_PCIE_PME=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_DOMAINS_GENERIC=y +CONFIG_PCI_MSI=y +CONFIG_PCI_MSI_IRQ_DOMAIN=y +CONFIG_PERF_USE_VMALLOC=y +CONFIG_PGTABLE_LEVELS=3 +CONFIG_PHYLIB=y +CONFIG_PHYS_ADDR_T_64BIT=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_BCM2835=y +CONFIG_PM=y +CONFIG_PM_CLK=y +CONFIG_PM_GENERIC_DOMAINS=y +CONFIG_PM_GENERIC_DOMAINS_OF=y +CONFIG_PM_GENERIC_DOMAINS_SLEEP=y +CONFIG_PM_OPP=y +CONFIG_PM_SLEEP=y +CONFIG_PM_SLEEP_SMP=y +CONFIG_POWER_SUPPLY=y +CONFIG_PRINTK_TIME=y +CONFIG_RAS=y +CONFIG_RASPBERRYPI_FIRMWARE=y +CONFIG_RASPBERRYPI_POWER=y +CONFIG_RATIONAL=y +# CONFIG_RAVE_SP_CORE is not set +CONFIG_RAW_DRIVER=y +CONFIG_RCU_NEED_SEGCBLIST=y +CONFIG_RCU_STALL_COMMON=y +CONFIG_REGMAP=y +CONFIG_REGMAP_MMIO=y +CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y +CONFIG_REGULATOR_GPIO=y +CONFIG_RESET_CONTROLLER=y +CONFIG_RESET_RASPBERRYPI=y +CONFIG_RESET_SIMPLE=y +CONFIG_RFS_ACCEL=y +# CONFIG_RPIVID_MEM is not set +# CONFIG_RPI_POE_POWER is not set +CONFIG_RPS=y +CONFIG_RWSEM_SPIN_ON_OWNER=y +CONFIG_SCSI=y +# CONFIG_SCSI_LOWLEVEL is not set +# CONFIG_SCSI_PROC_FS is not set +CONFIG_SERIAL_8250_BCM2835AUX=y +# CONFIG_SERIAL_8250_DMA is not set +CONFIG_SERIAL_8250_EXTENDED=y +CONFIG_SERIAL_8250_FSL=y +CONFIG_SERIAL_8250_NR_UARTS=1 +CONFIG_SERIAL_8250_RUNTIME_UARTS=0 +CONFIG_SERIAL_8250_SHARE_IRQ=y +CONFIG_SERIAL_AMBA_PL011=y +CONFIG_SERIAL_AMBA_PL011_CONSOLE=y +CONFIG_SERIAL_DEV_BUS=y +# CONFIG_SERIAL_DEV_CTRL_TTYPORT is not set +CONFIG_SERIAL_MCTRL_GPIO=y +CONFIG_SERIAL_OF_PLATFORM=y +CONFIG_SG_POOL=y +CONFIG_SMP=y +CONFIG_SMP_ON_UP=y +CONFIG_SMSC_PHY=y +CONFIG_SPARSE_IRQ=y +CONFIG_SRCU=y +# CONFIG_STRIP_ASM_SYMS is not set +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y +CONFIG_SWIOTLB=y +CONFIG_SWPHY=y +CONFIG_SWP_EMULATE=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_SYS_SUPPORTS_HUGETLBFS=y +# CONFIG_TEXTSEARCH is not set +CONFIG_THERMAL=y +CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y +CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0 +CONFIG_THERMAL_GOV_STEP_WISE=y +CONFIG_THERMAL_OF=y +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_TIMER_OF=y +CONFIG_TIMER_PROBE=y +CONFIG_TMPFS_POSIX_ACL=y +CONFIG_TREE_RCU=y +CONFIG_TREE_SRCU=y +CONFIG_UEVENT_HELPER_PATH="" +# CONFIG_UID16 is not set +CONFIG_UNCOMPRESS_INCLUDE="debug/uncompress.h" +CONFIG_UNWINDER_ARM=y +CONFIG_USB=y +CONFIG_USB_ANNOUNCE_NEW_DEVICES=y +CONFIG_USB_COMMON=y +CONFIG_USB_DWCOTG=y +# CONFIG_USB_ETH is not set +CONFIG_USB_GADGET=y +CONFIG_USB_LAN78XX=y +CONFIG_USB_NET_DRIVERS=y +CONFIG_USB_NET_SMSC95XX=y +CONFIG_USB_PCI=y +CONFIG_USB_PHY=y +CONFIG_USB_STORAGE=y +CONFIG_USB_SUPPORT=y +CONFIG_USB_UAS=y +# CONFIG_USB_UHCI_HCD is not set +CONFIG_USB_USBNET=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_PCI=y +CONFIG_USB_XHCI_PLATFORM=y +CONFIG_USE_OF=y +CONFIG_VFP=y +CONFIG_VFPv3=y +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_VT_CONSOLE_SLEEP=y +CONFIG_VT_HW_CONSOLE_BINDING=y +CONFIG_WATCHDOG_CORE=y +CONFIG_XPS=y +CONFIG_XZ_DEC_ARM=y +CONFIG_XZ_DEC_BCJ=y +CONFIG_ZBOOT_ROM_BSS=0 +CONFIG_ZBOOT_ROM_TEXT=0 diff --git a/target/linux/bcm27xx/bcm2710/config-5.10 b/target/linux/bcm27xx/bcm2710/config-5.10 new file mode 100644 index 0000000000..d9598a9464 --- /dev/null +++ b/target/linux/bcm27xx/bcm2710/config-5.10 @@ -0,0 +1,448 @@ +CONFIG_64BIT=y +# CONFIG_AIO is not set +CONFIG_ARCH_BCM2835=y +CONFIG_ARCH_DMA_ADDR_T_64BIT=y +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +CONFIG_ARCH_KEEP_MEMBLOCK=y +CONFIG_ARCH_MMAP_RND_BITS=18 +CONFIG_ARCH_MMAP_RND_BITS_MAX=24 +CONFIG_ARCH_MMAP_RND_BITS_MIN=18 +CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN=11 +CONFIG_ARCH_PROC_KCORE_TEXT=y +CONFIG_ARCH_SELECT_MEMORY_MODEL=y +CONFIG_ARCH_SPARSEMEM_DEFAULT=y +CONFIG_ARCH_SPARSEMEM_ENABLE=y +CONFIG_ARCH_STACKWALK=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARM64=y +CONFIG_ARM64_4K_PAGES=y +CONFIG_ARM64_CNP=y +CONFIG_ARM64_ERRATUM_1165522=y +CONFIG_ARM64_ERRATUM_1286807=y +CONFIG_ARM64_ERRATUM_819472=y +CONFIG_ARM64_ERRATUM_824069=y +CONFIG_ARM64_ERRATUM_826319=y +CONFIG_ARM64_ERRATUM_827319=y +CONFIG_ARM64_ERRATUM_832075=y +CONFIG_ARM64_ERRATUM_843419=y +CONFIG_ARM64_HW_AFDBM=y +CONFIG_ARM64_MODULE_PLTS=y +CONFIG_ARM64_PAGE_SHIFT=12 +CONFIG_ARM64_PAN=y +CONFIG_ARM64_PA_BITS=48 +CONFIG_ARM64_PA_BITS_48=y +CONFIG_ARM64_PTR_AUTH=y +CONFIG_ARM64_SVE=y +CONFIG_ARM64_TAGGED_ADDR_ABI=y +CONFIG_ARM64_UAO=y +CONFIG_ARM64_VA_BITS=39 +CONFIG_ARM64_VA_BITS_39=y +CONFIG_ARM64_VHE=y +CONFIG_ARM64_WORKAROUND_CLEAN_CACHE=y +CONFIG_ARM64_WORKAROUND_REPEAT_TLBI=y +CONFIG_ARM64_WORKAROUND_SPECULATIVE_AT=y +CONFIG_ARM_AMBA=y +CONFIG_ARM_ARCH_TIMER=y +CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y +CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND=y +CONFIG_ARM_GIC=y +CONFIG_ARM_GIC_V2M=y +CONFIG_ARM_GIC_V3=y +CONFIG_ARM_GIC_V3_ITS=y +CONFIG_ARM_GIC_V3_ITS_PCI=y +CONFIG_ARM_PSCI_FW=y +CONFIG_ARM_RASPBERRYPI_CPUFREQ=y +CONFIG_ARM_TIMER_SP804=y +CONFIG_ASSOCIATIVE_ARRAY=y +CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y +CONFIG_BCM2708_VCMEM=y +# CONFIG_BCM2711_THERMAL is not set +CONFIG_BCM2835_DEVGPIOMEM=y +CONFIG_BCM2835_MBOX=y +CONFIG_BCM2835_POWER=y +# CONFIG_BCM2835_SMI is not set +CONFIG_BCM2835_THERMAL=y +CONFIG_BCM2835_VCHIQ=y +# CONFIG_BCM2835_VCHIQ_MMAL is not set +CONFIG_BCM2835_WDT=y +CONFIG_BCM_VCIO=y +# CONFIG_BCM_VC_SM_CMA is not set +CONFIG_BCM_VIDEOCORE=y +# CONFIG_BLK_DEV_INITRD is not set +CONFIG_BLK_DEV_LOOP=y +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +CONFIG_BLK_DEV_SD=y +CONFIG_BLK_MQ_PCI=y +CONFIG_BLK_PM=y +CONFIG_BLK_SCSI_REQUEST=y +CONFIG_BOUNCE=y +CONFIG_BRCMSTB_L2_IRQ=y +CONFIG_BRCM_CHAR_DRIVERS=y +CONFIG_CAVIUM_ERRATUM_22375=y +CONFIG_CAVIUM_ERRATUM_23154=y +CONFIG_CAVIUM_ERRATUM_27456=y +CONFIG_CAVIUM_TX2_ERRATUM_219=y +CONFIG_CC_HAVE_STACKPROTECTOR_SYSREG=y +CONFIG_CLKDEV_LOOKUP=y +CONFIG_CLKSRC_MMIO=y +CONFIG_CLK_BCM2711_DVP=y +CONFIG_CLK_BCM2835=y +CONFIG_CLK_RASPBERRYPI=y +CONFIG_CLONE_BACKWARDS=y +CONFIG_CMA=y +CONFIG_CMA_ALIGNMENT=8 +CONFIG_CMA_AREAS=7 +# CONFIG_CMA_DEBUG is not set +# CONFIG_CMA_DEBUGFS is not set +CONFIG_CMA_SIZE_MBYTES=5 +# CONFIG_CMA_SIZE_SEL_MAX is not set +CONFIG_CMA_SIZE_SEL_MBYTES=y +# CONFIG_CMA_SIZE_SEL_MIN is not set +# CONFIG_CMA_SIZE_SEL_PERCENTAGE is not set +CONFIG_COMMON_CLK=y +CONFIG_COMMON_CLK_XGENE=y +# CONFIG_COMPAT_32BIT_TIME is not set +CONFIG_CONFIGFS_FS=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_CONTIG_ALLOC=y +CONFIG_CPUFREQ_DT=y +CONFIG_CPUFREQ_DT_PLATDEV=y +CONFIG_CPU_FREQ=y +CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y +# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set +CONFIG_CPU_FREQ_GOV_ATTR_SET=y +CONFIG_CPU_FREQ_GOV_COMMON=y +CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y +CONFIG_CPU_FREQ_GOV_ONDEMAND=y +CONFIG_CPU_FREQ_GOV_PERFORMANCE=y +CONFIG_CPU_FREQ_GOV_POWERSAVE=y +CONFIG_CPU_FREQ_GOV_USERSPACE=y +CONFIG_CPU_FREQ_STAT=y +CONFIG_CPU_IDLE=y +CONFIG_CPU_IDLE_GOV_LADDER=y +CONFIG_CPU_IDLE_GOV_MENU=y +CONFIG_CPU_PM=y +CONFIG_CPU_RMAP=y +CONFIG_CRC16=y +CONFIG_CRYPTO_CBC=y +CONFIG_CRYPTO_CRC32=y +CONFIG_CRYPTO_CRC32C=y +CONFIG_CRYPTO_CTS=y +CONFIG_CRYPTO_DRBG=y +CONFIG_CRYPTO_DRBG_HMAC=y +CONFIG_CRYPTO_DRBG_MENU=y +CONFIG_CRYPTO_ECB=y +CONFIG_CRYPTO_GF128MUL=y +CONFIG_CRYPTO_HMAC=y +CONFIG_CRYPTO_JITTERENTROPY=y +CONFIG_CRYPTO_LIB_SHA256=y +CONFIG_CRYPTO_NULL2=y +CONFIG_CRYPTO_RNG=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_RNG_DEFAULT=y +CONFIG_CRYPTO_SEQIV=y +CONFIG_CRYPTO_SHA256=y +CONFIG_CRYPTO_SHA512=y +CONFIG_CRYPTO_XTS=y +CONFIG_DCACHE_WORD_ACCESS=y +CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_DEBUG_INFO=y +CONFIG_DMABUF_HEAPS=y +CONFIG_DMABUF_HEAPS_CMA=y +CONFIG_DMABUF_HEAPS_SYSTEM=y +CONFIG_DMADEVICES=y +CONFIG_DMA_BCM2708=y +CONFIG_DMA_BCM2835=y +CONFIG_DMA_CMA=y +CONFIG_DMA_DIRECT_REMAP=y +CONFIG_DMA_ENGINE=y +CONFIG_DMA_OF=y +CONFIG_DMA_REMAP=y +CONFIG_DMA_SHARED_BUFFER=y +CONFIG_DMA_VIRTUAL_CHANNELS=y +CONFIG_DNOTIFY=y +CONFIG_DTC=y +CONFIG_DUMMY_CONSOLE=y +CONFIG_EDAC_SUPPORT=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_EXT4_FS=y +CONFIG_EXT4_FS_POSIX_ACL=y +CONFIG_EXT4_FS_SECURITY=y +CONFIG_EXTCON=y +CONFIG_F2FS_FS=y +CONFIG_FB=y +CONFIG_FB_BCM2708=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_IMAGEBLIT=y +CONFIG_FB_CMDLINE=y +# CONFIG_FB_RPISENSE is not set +CONFIG_FB_SIMPLE=y +CONFIG_FIXED_PHY=y +CONFIG_FIX_EARLYCON_MEM=y +# CONFIG_FLATMEM_MANUAL is not set +CONFIG_FONT_8x16=y +CONFIG_FONT_8x8=y +CONFIG_FONT_SUPPORT=y +CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set +CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y +CONFIG_FRAME_POINTER=y +CONFIG_FREEZER=y +CONFIG_FSL_ERRATUM_A008585=y +CONFIG_FS_ENCRYPTION=y +CONFIG_FS_ENCRYPTION_ALGS=y +CONFIG_FS_IOMAP=y +CONFIG_FS_MBCACHE=y +CONFIG_FS_POSIX_ACL=y +CONFIG_FUJITSU_ERRATUM_010001=y +CONFIG_FW_CACHE=y +CONFIG_FW_LOADER_PAGED_BUF=y +CONFIG_GENERIC_ALLOCATOR=y +CONFIG_GENERIC_ARCH_TOPOLOGY=y +CONFIG_GENERIC_BUG=y +CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y +CONFIG_GENERIC_CPU_AUTOPROBE=y +CONFIG_GENERIC_CPU_VULNERABILITIES=y +CONFIG_GENERIC_CSUM=y +CONFIG_GENERIC_EARLY_IOREMAP=y +CONFIG_GENERIC_GETTIMEOFDAY=y +CONFIG_GENERIC_IDLE_POLL_SETUP=y +CONFIG_GENERIC_IRQ_CHIP=y +CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y +CONFIG_GENERIC_IRQ_MIGRATION=y +CONFIG_GENERIC_IRQ_MULTI_HANDLER=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_IRQ_SHOW_LEVEL=y +CONFIG_GENERIC_MSI_IRQ=y +CONFIG_GENERIC_MSI_IRQ_DOMAIN=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_PINCONF=y +CONFIG_GENERIC_PINCTRL_GROUPS=y +CONFIG_GENERIC_PINMUX_FUNCTIONS=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_STRNCPY_FROM_USER=y +CONFIG_GENERIC_STRNLEN_USER=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GPIOLIB=y +CONFIG_GPIOLIB_IRQCHIP=y +CONFIG_GPIO_BCM_VIRT=y +# CONFIG_GPIO_FSM is not set +CONFIG_GPIO_RASPBERRYPI_EXP=y +CONFIG_HANDLE_DOMAIN_IRQ=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT_MAP=y +CONFIG_HOLES_IN_ZONE=y +CONFIG_HOTPLUG_CPU=y +CONFIG_HW_CONSOLE=y +CONFIG_HW_RANDOM=y +CONFIG_HW_RANDOM_BCM2835=y +CONFIG_I2C=y +# CONFIG_I2C_BCM2708 is not set +CONFIG_I2C_BOARDINFO=y +# CONFIG_I2C_BRCMSTB is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000 +CONFIG_INPUT=y +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +CONFIG_IRQCHIP=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_DOMAIN_HIERARCHY=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_WORK=y +CONFIG_JBD2=y +CONFIG_KEYS=y +CONFIG_LEDS_GPIO=y +CONFIG_LEDS_TRIGGER_ACTPWR=y +CONFIG_LEDS_TRIGGER_INPUT=y +CONFIG_LIBFDT=y +CONFIG_LLD_VERSION=0 +CONFIG_LOCK_DEBUGGING_SUPPORT=y +CONFIG_LOCK_SPIN_ON_OWNER=y +CONFIG_LOGO=y +CONFIG_LOGO_LINUX_CLUT224=y +# CONFIG_LOGO_LINUX_MONO is not set +# CONFIG_LOGO_LINUX_VGA16 is not set +CONFIG_MAC_PARTITION=y +CONFIG_MAGIC_SYSRQ=y +CONFIG_MAILBOX=y +# CONFIG_MAILBOX_TEST is not set +CONFIG_MAX_RAW_DEVS=256 +CONFIG_MDIO_BUS=y +CONFIG_MDIO_DEVICE=y +CONFIG_MDIO_DEVRES=y +CONFIG_MEMFD_CREATE=y +CONFIG_MEMORY_ISOLATION=y +CONFIG_MFD_CORE=y +# CONFIG_MFD_RPISENSE_CORE is not set +CONFIG_MFD_SYSCON=y +CONFIG_MICROCHIP_PHY=y +CONFIG_MIGRATION=y +CONFIG_MMC=y +CONFIG_MMC_BCM2835=y +CONFIG_MMC_BCM2835_DMA=y +CONFIG_MMC_BCM2835_MMC=y +CONFIG_MMC_BCM2835_PIO_DMA_BARRIER=2 +CONFIG_MMC_BCM2835_SDHOST=y +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_MINORS=32 +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_IO_ACCESSORS=y +CONFIG_MMC_SDHCI_IPROC=y +# CONFIG_MMC_SDHCI_PCI is not set +CONFIG_MMC_SDHCI_PLTFM=y +CONFIG_MODULES_USE_ELF_RELA=y +# CONFIG_MTD is not set +CONFIG_MUTEX_SPIN_ON_OWNER=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NEED_SG_DMA_LENGTH=y +CONFIG_NET_FLOW_LIMIT=y +CONFIG_NLS=y +CONFIG_NLS_ASCII=y +CONFIG_NO_HZ=y +CONFIG_NO_HZ_COMMON=y +CONFIG_NO_HZ_IDLE=y +CONFIG_NR_CPUS=4 +CONFIG_NVMEM=y +# CONFIG_NVMEM_RMEM is not set +CONFIG_OF=y +CONFIG_OF_ADDRESS=y +CONFIG_OF_CONFIGFS=y +CONFIG_OF_DYNAMIC=y +CONFIG_OF_EARLY_FLATTREE=y +CONFIG_OF_FLATTREE=y +CONFIG_OF_GPIO=y +CONFIG_OF_IRQ=y +CONFIG_OF_KOBJ=y +CONFIG_OF_MDIO=y +CONFIG_OF_NET=y +CONFIG_OF_OVERLAY=y +CONFIG_OF_RESOLVE=y +CONFIG_PADATA=y +CONFIG_PARTITION_PERCPU=y +CONFIG_PCI=y +# CONFIG_PCIE_BRCMSTB is not set +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_DOMAINS_GENERIC=y +CONFIG_PCI_MSI=y +CONFIG_PCI_MSI_IRQ_DOMAIN=y +CONFIG_PGTABLE_LEVELS=3 +CONFIG_PHYLIB=y +CONFIG_PHYS_ADDR_T_64BIT=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_BCM2835=y +CONFIG_PM=y +CONFIG_PM_CLK=y +CONFIG_PM_GENERIC_DOMAINS=y +CONFIG_PM_GENERIC_DOMAINS_OF=y +CONFIG_PM_GENERIC_DOMAINS_SLEEP=y +CONFIG_PM_OPP=y +CONFIG_PM_SLEEP=y +CONFIG_PM_SLEEP_SMP=y +CONFIG_POWER_RESET=y +CONFIG_POWER_SUPPLY=y +CONFIG_PRINTK_TIME=y +CONFIG_QUEUED_RWLOCKS=y +CONFIG_QUEUED_SPINLOCKS=y +CONFIG_RASPBERRYPI_FIRMWARE=y +CONFIG_RASPBERRYPI_POWER=y +CONFIG_RATIONAL=y +# CONFIG_RAVE_SP_CORE is not set +CONFIG_RAW_DRIVER=y +CONFIG_RCU_NEED_SEGCBLIST=y +CONFIG_RCU_STALL_COMMON=y +CONFIG_REGMAP=y +CONFIG_REGMAP_MMIO=y +CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y +CONFIG_REGULATOR_GPIO=y +CONFIG_RESET_CONTROLLER=y +# CONFIG_RESET_RASPBERRYPI is not set +CONFIG_RESET_SIMPLE=y +CONFIG_RFS_ACCEL=y +CONFIG_RODATA_FULL_DEFAULT_ENABLED=y +# CONFIG_RPIVID_MEM is not set +# CONFIG_RPI_POE_POWER is not set +CONFIG_RPS=y +CONFIG_RWSEM_SPIN_ON_OWNER=y +CONFIG_SCSI=y +# CONFIG_SCSI_LOWLEVEL is not set +# CONFIG_SCSI_PROC_FS is not set +CONFIG_SERIAL_8250_BCM2835AUX=y +# CONFIG_SERIAL_8250_DMA is not set +CONFIG_SERIAL_8250_EXTENDED=y +CONFIG_SERIAL_8250_FSL=y +CONFIG_SERIAL_8250_NR_UARTS=1 +CONFIG_SERIAL_8250_RUNTIME_UARTS=0 +CONFIG_SERIAL_8250_SHARE_IRQ=y +CONFIG_SERIAL_AMBA_PL011=y +CONFIG_SERIAL_AMBA_PL011_CONSOLE=y +CONFIG_SERIAL_DEV_BUS=y +# CONFIG_SERIAL_DEV_CTRL_TTYPORT is not set +CONFIG_SERIAL_MCTRL_GPIO=y +CONFIG_SERIAL_OF_PLATFORM=y +CONFIG_SG_POOL=y +CONFIG_SMP=y +CONFIG_SMSC_PHY=y +CONFIG_SPARSEMEM=y +CONFIG_SPARSEMEM_EXTREME=y +CONFIG_SPARSEMEM_MANUAL=y +CONFIG_SPARSEMEM_VMEMMAP=y +CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y +CONFIG_SPARSE_IRQ=y +CONFIG_SRCU=y +# CONFIG_STRIP_ASM_SYMS is not set +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y +CONFIG_SWIOTLB=y +CONFIG_SWPHY=y +CONFIG_SYSCTL_EXCEPTION_TRACE=y +CONFIG_SYS_SUPPORTS_HUGETLBFS=y +# CONFIG_TEXTSEARCH is not set +CONFIG_THERMAL=y +CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y +CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0 +CONFIG_THERMAL_GOV_STEP_WISE=y +CONFIG_THERMAL_OF=y +CONFIG_THERMAL_WRITABLE_TRIPS=y +CONFIG_THREAD_INFO_IN_TASK=y +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_TIMER_OF=y +CONFIG_TIMER_PROBE=y +CONFIG_TMPFS_POSIX_ACL=y +CONFIG_TREE_RCU=y +CONFIG_TREE_SRCU=y +CONFIG_UEVENT_HELPER_PATH="" +CONFIG_UNMAP_KERNEL_AT_EL0=y +CONFIG_USB=y +CONFIG_USB_ANNOUNCE_NEW_DEVICES=y +CONFIG_USB_COMMON=y +CONFIG_USB_DWCOTG=y +CONFIG_USB_LAN78XX=y +CONFIG_USB_NET_DRIVERS=y +CONFIG_USB_NET_SMSC95XX=y +CONFIG_USB_STORAGE=y +CONFIG_USB_SUPPORT=y +CONFIG_USB_UAS=y +CONFIG_USB_USBNET=y +CONFIG_VMAP_STACK=y +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_VT_CONSOLE_SLEEP=y +CONFIG_VT_HW_CONSOLE_BINDING=y +CONFIG_WATCHDOG_CORE=y +CONFIG_XPS=y +CONFIG_XZ_DEC_ARM=y +CONFIG_XZ_DEC_BCJ=y +CONFIG_ZONE_DMA32=y diff --git a/target/linux/bcm27xx/bcm2711/config-5.10 b/target/linux/bcm27xx/bcm2711/config-5.10 new file mode 100644 index 0000000000..4fd9dc5ddc --- /dev/null +++ b/target/linux/bcm27xx/bcm2711/config-5.10 @@ -0,0 +1,463 @@ +CONFIG_64BIT=y +# CONFIG_AIO is not set +CONFIG_ARCH_BCM2835=y +CONFIG_ARCH_DMA_ADDR_T_64BIT=y +CONFIG_ARCH_HIBERNATION_POSSIBLE=y +CONFIG_ARCH_KEEP_MEMBLOCK=y +CONFIG_ARCH_MMAP_RND_BITS=18 +CONFIG_ARCH_MMAP_RND_BITS_MAX=24 +CONFIG_ARCH_MMAP_RND_BITS_MIN=18 +CONFIG_ARCH_MMAP_RND_COMPAT_BITS_MIN=11 +CONFIG_ARCH_PROC_KCORE_TEXT=y +CONFIG_ARCH_SELECT_MEMORY_MODEL=y +CONFIG_ARCH_SPARSEMEM_DEFAULT=y +CONFIG_ARCH_SPARSEMEM_ENABLE=y +CONFIG_ARCH_STACKWALK=y +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_ARM64=y +CONFIG_ARM64_4K_PAGES=y +CONFIG_ARM64_CNP=y +CONFIG_ARM64_ERRATUM_1165522=y +CONFIG_ARM64_ERRATUM_1286807=y +CONFIG_ARM64_ERRATUM_819472=y +CONFIG_ARM64_ERRATUM_824069=y +CONFIG_ARM64_ERRATUM_826319=y +CONFIG_ARM64_ERRATUM_827319=y +CONFIG_ARM64_ERRATUM_832075=y +CONFIG_ARM64_ERRATUM_843419=y +CONFIG_ARM64_HW_AFDBM=y +CONFIG_ARM64_MODULE_PLTS=y +CONFIG_ARM64_PAGE_SHIFT=12 +CONFIG_ARM64_PAN=y +CONFIG_ARM64_PA_BITS=48 +CONFIG_ARM64_PA_BITS_48=y +CONFIG_ARM64_PTR_AUTH=y +CONFIG_ARM64_SVE=y +CONFIG_ARM64_TAGGED_ADDR_ABI=y +CONFIG_ARM64_UAO=y +CONFIG_ARM64_VA_BITS=39 +CONFIG_ARM64_VA_BITS_39=y +CONFIG_ARM64_VHE=y +CONFIG_ARM64_WORKAROUND_CLEAN_CACHE=y +CONFIG_ARM64_WORKAROUND_REPEAT_TLBI=y +CONFIG_ARM64_WORKAROUND_SPECULATIVE_AT=y +CONFIG_ARM_AMBA=y +CONFIG_ARM_ARCH_TIMER=y +CONFIG_ARM_ARCH_TIMER_EVTSTREAM=y +CONFIG_ARM_ARCH_TIMER_OOL_WORKAROUND=y +CONFIG_ARM_GIC=y +CONFIG_ARM_GIC_V2M=y +CONFIG_ARM_GIC_V3=y +CONFIG_ARM_GIC_V3_ITS=y +CONFIG_ARM_GIC_V3_ITS_PCI=y +CONFIG_ARM_PSCI_FW=y +CONFIG_ARM_RASPBERRYPI_CPUFREQ=y +CONFIG_ARM_TIMER_SP804=y +CONFIG_ASSOCIATIVE_ARRAY=y +CONFIG_AUDIT_ARCH_COMPAT_GENERIC=y +CONFIG_BCM2708_VCMEM=y +CONFIG_BCM2711_THERMAL=y +CONFIG_BCM2835_DEVGPIOMEM=y +CONFIG_BCM2835_MBOX=y +CONFIG_BCM2835_POWER=y +# CONFIG_BCM2835_SMI is not set +# CONFIG_BCM2835_THERMAL is not set +CONFIG_BCM2835_VCHIQ=y +# CONFIG_BCM2835_VCHIQ_MMAL is not set +CONFIG_BCM2835_WDT=y +CONFIG_BCM7XXX_PHY=y +CONFIG_BCMGENET=y +CONFIG_BCM_NET_PHYLIB=y +CONFIG_BCM_VCIO=y +# CONFIG_BCM_VC_SM_CMA is not set +CONFIG_BCM_VIDEOCORE=y +# CONFIG_BLK_DEV_INITRD is not set +CONFIG_BLK_DEV_LOOP=y +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=4096 +CONFIG_BLK_DEV_SD=y +CONFIG_BLK_MQ_PCI=y +CONFIG_BLK_PM=y +CONFIG_BLK_SCSI_REQUEST=y +CONFIG_BOUNCE=y +CONFIG_BRCMSTB_L2_IRQ=y +CONFIG_BRCM_CHAR_DRIVERS=y +CONFIG_BROADCOM_PHY=y +CONFIG_CAVIUM_ERRATUM_22375=y +CONFIG_CAVIUM_ERRATUM_23154=y +CONFIG_CAVIUM_ERRATUM_27456=y +CONFIG_CAVIUM_TX2_ERRATUM_219=y +CONFIG_CC_HAVE_STACKPROTECTOR_SYSREG=y +CONFIG_CLKDEV_LOOKUP=y +CONFIG_CLKSRC_MMIO=y +CONFIG_CLK_BCM2711_DVP=y +CONFIG_CLK_BCM2835=y +CONFIG_CLK_RASPBERRYPI=y +CONFIG_CLONE_BACKWARDS=y +CONFIG_CMA=y +CONFIG_CMA_ALIGNMENT=8 +CONFIG_CMA_AREAS=7 +# CONFIG_CMA_DEBUG is not set +# CONFIG_CMA_DEBUGFS is not set +CONFIG_CMA_SIZE_MBYTES=5 +# CONFIG_CMA_SIZE_SEL_MAX is not set +CONFIG_CMA_SIZE_SEL_MBYTES=y +# CONFIG_CMA_SIZE_SEL_MIN is not set +# CONFIG_CMA_SIZE_SEL_PERCENTAGE is not set +CONFIG_COMMON_CLK=y +CONFIG_COMMON_CLK_XGENE=y +# CONFIG_COMPAT_32BIT_TIME is not set +CONFIG_CONFIGFS_FS=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_CONTIG_ALLOC=y +CONFIG_CPUFREQ_DT=y +CONFIG_CPUFREQ_DT_PLATDEV=y +CONFIG_CPU_FREQ=y +CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y +# CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE is not set +CONFIG_CPU_FREQ_GOV_ATTR_SET=y +CONFIG_CPU_FREQ_GOV_COMMON=y +CONFIG_CPU_FREQ_GOV_CONSERVATIVE=y +CONFIG_CPU_FREQ_GOV_ONDEMAND=y +CONFIG_CPU_FREQ_GOV_PERFORMANCE=y +CONFIG_CPU_FREQ_GOV_POWERSAVE=y +CONFIG_CPU_FREQ_GOV_USERSPACE=y +CONFIG_CPU_FREQ_STAT=y +CONFIG_CPU_IDLE=y +CONFIG_CPU_IDLE_GOV_LADDER=y +CONFIG_CPU_IDLE_GOV_MENU=y +CONFIG_CPU_PM=y +CONFIG_CPU_RMAP=y +CONFIG_CRC16=y +CONFIG_CRYPTO_CBC=y +CONFIG_CRYPTO_CRC32=y +CONFIG_CRYPTO_CRC32C=y +CONFIG_CRYPTO_CTS=y +CONFIG_CRYPTO_DRBG=y +CONFIG_CRYPTO_DRBG_HMAC=y +CONFIG_CRYPTO_DRBG_MENU=y +CONFIG_CRYPTO_ECB=y +CONFIG_CRYPTO_GF128MUL=y +CONFIG_CRYPTO_HMAC=y +CONFIG_CRYPTO_JITTERENTROPY=y +CONFIG_CRYPTO_LIB_SHA256=y +CONFIG_CRYPTO_NULL2=y +CONFIG_CRYPTO_RNG=y +CONFIG_CRYPTO_RNG2=y +CONFIG_CRYPTO_RNG_DEFAULT=y +CONFIG_CRYPTO_SEQIV=y +CONFIG_CRYPTO_SHA256=y +CONFIG_CRYPTO_SHA512=y +CONFIG_CRYPTO_XTS=y +CONFIG_DCACHE_WORD_ACCESS=y +CONFIG_DEBUG_BUGVERBOSE=y +CONFIG_DEBUG_INFO=y +CONFIG_DIMLIB=y +CONFIG_DMABUF_HEAPS=y +CONFIG_DMABUF_HEAPS_CMA=y +CONFIG_DMABUF_HEAPS_SYSTEM=y +CONFIG_DMADEVICES=y +CONFIG_DMA_BCM2708=y +CONFIG_DMA_BCM2835=y +CONFIG_DMA_CMA=y +CONFIG_DMA_DIRECT_REMAP=y +CONFIG_DMA_ENGINE=y +CONFIG_DMA_OF=y +CONFIG_DMA_REMAP=y +CONFIG_DMA_SHARED_BUFFER=y +CONFIG_DMA_VIRTUAL_CHANNELS=y +CONFIG_DNOTIFY=y +CONFIG_DTC=y +CONFIG_DUMMY_CONSOLE=y +CONFIG_EDAC_SUPPORT=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_EXT4_FS=y +CONFIG_EXT4_FS_POSIX_ACL=y +CONFIG_EXT4_FS_SECURITY=y +CONFIG_EXTCON=y +CONFIG_F2FS_FS=y +CONFIG_FB=y +CONFIG_FB_BCM2708=y +CONFIG_FB_CFB_COPYAREA=y +CONFIG_FB_CFB_FILLRECT=y +CONFIG_FB_CFB_IMAGEBLIT=y +CONFIG_FB_CMDLINE=y +# CONFIG_FB_RPISENSE is not set +CONFIG_FB_SIMPLE=y +CONFIG_FIXED_PHY=y +CONFIG_FIX_EARLYCON_MEM=y +# CONFIG_FLATMEM_MANUAL is not set +CONFIG_FONT_8x16=y +CONFIG_FONT_8x8=y +CONFIG_FONT_SUPPORT=y +CONFIG_FRAMEBUFFER_CONSOLE=y +# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set +CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y +CONFIG_FRAME_POINTER=y +CONFIG_FREEZER=y +CONFIG_FSL_ERRATUM_A008585=y +CONFIG_FS_ENCRYPTION=y +CONFIG_FS_ENCRYPTION_ALGS=y +CONFIG_FS_IOMAP=y +CONFIG_FS_MBCACHE=y +CONFIG_FS_POSIX_ACL=y +CONFIG_FUJITSU_ERRATUM_010001=y +CONFIG_FW_CACHE=y +CONFIG_FW_LOADER_PAGED_BUF=y +CONFIG_GENERIC_ALLOCATOR=y +CONFIG_GENERIC_ARCH_TOPOLOGY=y +CONFIG_GENERIC_BUG=y +CONFIG_GENERIC_BUG_RELATIVE_POINTERS=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_GENERIC_CLOCKEVENTS_BROADCAST=y +CONFIG_GENERIC_CPU_AUTOPROBE=y +CONFIG_GENERIC_CPU_VULNERABILITIES=y +CONFIG_GENERIC_CSUM=y +CONFIG_GENERIC_EARLY_IOREMAP=y +CONFIG_GENERIC_GETTIMEOFDAY=y +CONFIG_GENERIC_IDLE_POLL_SETUP=y +CONFIG_GENERIC_IRQ_CHIP=y +CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK=y +CONFIG_GENERIC_IRQ_MIGRATION=y +CONFIG_GENERIC_IRQ_MULTI_HANDLER=y +CONFIG_GENERIC_IRQ_SHOW=y +CONFIG_GENERIC_IRQ_SHOW_LEVEL=y +CONFIG_GENERIC_MSI_IRQ=y +CONFIG_GENERIC_MSI_IRQ_DOMAIN=y +CONFIG_GENERIC_PCI_IOMAP=y +CONFIG_GENERIC_PHY=y +CONFIG_GENERIC_PINCONF=y +CONFIG_GENERIC_PINCTRL_GROUPS=y +CONFIG_GENERIC_PINMUX_FUNCTIONS=y +CONFIG_GENERIC_SCHED_CLOCK=y +CONFIG_GENERIC_SMP_IDLE_THREAD=y +CONFIG_GENERIC_STRNCPY_FROM_USER=y +CONFIG_GENERIC_STRNLEN_USER=y +CONFIG_GENERIC_TIME_VSYSCALL=y +CONFIG_GPIOLIB=y +CONFIG_GPIOLIB_IRQCHIP=y +CONFIG_GPIO_BCM_VIRT=y +# CONFIG_GPIO_FSM is not set +CONFIG_GPIO_RASPBERRYPI_EXP=y +CONFIG_HANDLE_DOMAIN_IRQ=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT_MAP=y +CONFIG_HOLES_IN_ZONE=y +CONFIG_HOTPLUG_CPU=y +CONFIG_HW_CONSOLE=y +CONFIG_HW_RANDOM=y +# CONFIG_HW_RANDOM_BCM2835 is not set +CONFIG_HW_RANDOM_IPROC_RNG200=y +CONFIG_I2C=y +# CONFIG_I2C_BCM2708 is not set +CONFIG_I2C_BOARDINFO=y +# CONFIG_I2C_BRCMSTB is not set +CONFIG_IKCONFIG=y +CONFIG_IKCONFIG_PROC=y +CONFIG_ILLEGAL_POINTER_VALUE=0xdead000000000000 +CONFIG_INPUT=y +CONFIG_INPUT_MOUSEDEV=y +# CONFIG_INPUT_MOUSEDEV_PSAUX is not set +CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024 +CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768 +CONFIG_IRQCHIP=y +CONFIG_IRQ_DOMAIN=y +CONFIG_IRQ_DOMAIN_HIERARCHY=y +CONFIG_IRQ_FORCED_THREADING=y +CONFIG_IRQ_WORK=y +CONFIG_JBD2=y +CONFIG_KEYS=y +CONFIG_LEDS_GPIO=y +CONFIG_LEDS_TRIGGER_ACTPWR=y +CONFIG_LEDS_TRIGGER_INPUT=y +CONFIG_LIBFDT=y +CONFIG_LLD_VERSION=0 +CONFIG_LOCK_DEBUGGING_SUPPORT=y +CONFIG_LOCK_SPIN_ON_OWNER=y +CONFIG_LOGO=y +CONFIG_LOGO_LINUX_CLUT224=y +# CONFIG_LOGO_LINUX_MONO is not set +# CONFIG_LOGO_LINUX_VGA16 is not set +CONFIG_MAC_PARTITION=y +CONFIG_MAGIC_SYSRQ=y +CONFIG_MAILBOX=y +# CONFIG_MAILBOX_TEST is not set +CONFIG_MAX_RAW_DEVS=256 +CONFIG_MDIO_BCM_UNIMAC=y +CONFIG_MDIO_BUS=y +CONFIG_MDIO_DEVICE=y +CONFIG_MDIO_DEVRES=y +CONFIG_MEMFD_CREATE=y +CONFIG_MEMORY_ISOLATION=y +CONFIG_MFD_CORE=y +# CONFIG_MFD_RPISENSE_CORE is not set +CONFIG_MFD_SYSCON=y +CONFIG_MIGRATION=y +CONFIG_MMC=y +CONFIG_MMC_BCM2835=y +CONFIG_MMC_BCM2835_DMA=y +CONFIG_MMC_BCM2835_MMC=y +CONFIG_MMC_BCM2835_PIO_DMA_BARRIER=2 +CONFIG_MMC_BCM2835_SDHOST=y +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_MINORS=32 +CONFIG_MMC_SDHCI=y +CONFIG_MMC_SDHCI_IO_ACCESSORS=y +CONFIG_MMC_SDHCI_IPROC=y +# CONFIG_MMC_SDHCI_PCI is not set +CONFIG_MMC_SDHCI_PLTFM=y +CONFIG_MODULES_USE_ELF_RELA=y +# CONFIG_MTD is not set +CONFIG_MUTEX_SPIN_ON_OWNER=y +CONFIG_NEED_DMA_MAP_STATE=y +CONFIG_NEED_SG_DMA_LENGTH=y +CONFIG_NET_FLOW_LIMIT=y +CONFIG_NLS=y +CONFIG_NLS_ASCII=y +CONFIG_NOP_USB_XCEIV=y +CONFIG_NO_HZ=y +CONFIG_NO_HZ_COMMON=y +CONFIG_NO_HZ_IDLE=y +CONFIG_NR_CPUS=4 +CONFIG_NVMEM=y +# CONFIG_NVMEM_RMEM is not set +CONFIG_OF=y +CONFIG_OF_ADDRESS=y +CONFIG_OF_CONFIGFS=y +CONFIG_OF_DYNAMIC=y +CONFIG_OF_EARLY_FLATTREE=y +CONFIG_OF_FLATTREE=y +CONFIG_OF_GPIO=y +CONFIG_OF_IRQ=y +CONFIG_OF_KOBJ=y +CONFIG_OF_MDIO=y +CONFIG_OF_NET=y +CONFIG_OF_OVERLAY=y +CONFIG_OF_RESOLVE=y +CONFIG_PADATA=y +CONFIG_PARTITION_PERCPU=y +CONFIG_PCI=y +CONFIG_PCIEAER=y +CONFIG_PCIEPORTBUS=y +CONFIG_PCIE_BRCMSTB=y +CONFIG_PCIE_PME=y +CONFIG_PCI_DOMAINS=y +CONFIG_PCI_DOMAINS_GENERIC=y +CONFIG_PCI_MSI=y +CONFIG_PCI_MSI_IRQ_DOMAIN=y +CONFIG_PGTABLE_LEVELS=3 +CONFIG_PHYLIB=y +CONFIG_PHYS_ADDR_T_64BIT=y +CONFIG_PINCTRL=y +CONFIG_PINCTRL_BCM2835=y +CONFIG_PM=y +CONFIG_PM_CLK=y +CONFIG_PM_GENERIC_DOMAINS=y +CONFIG_PM_GENERIC_DOMAINS_OF=y +CONFIG_PM_GENERIC_DOMAINS_SLEEP=y +CONFIG_PM_OPP=y +CONFIG_PM_SLEEP=y +CONFIG_PM_SLEEP_SMP=y +CONFIG_POWER_RESET=y +CONFIG_POWER_SUPPLY=y +CONFIG_PRINTK_TIME=y +CONFIG_QUEUED_RWLOCKS=y +CONFIG_QUEUED_SPINLOCKS=y +CONFIG_RAS=y +CONFIG_RASPBERRYPI_FIRMWARE=y +CONFIG_RASPBERRYPI_POWER=y +CONFIG_RATIONAL=y +# CONFIG_RAVE_SP_CORE is not set +CONFIG_RAW_DRIVER=y +CONFIG_RCU_NEED_SEGCBLIST=y +CONFIG_RCU_STALL_COMMON=y +CONFIG_REGMAP=y +CONFIG_REGMAP_MMIO=y +CONFIG_REGULATOR=y +CONFIG_REGULATOR_FIXED_VOLTAGE=y +CONFIG_REGULATOR_GPIO=y +CONFIG_RESET_CONTROLLER=y +CONFIG_RESET_RASPBERRYPI=y +CONFIG_RESET_SIMPLE=y +CONFIG_RFS_ACCEL=y +CONFIG_RODATA_FULL_DEFAULT_ENABLED=y +# CONFIG_RPIVID_MEM is not set +# CONFIG_RPI_POE_POWER is not set +CONFIG_RPS=y +CONFIG_RWSEM_SPIN_ON_OWNER=y +CONFIG_SCSI=y +# CONFIG_SCSI_LOWLEVEL is not set +# CONFIG_SCSI_PROC_FS is not set +CONFIG_SERIAL_8250_BCM2835AUX=y +# CONFIG_SERIAL_8250_DMA is not set +CONFIG_SERIAL_8250_EXTENDED=y +CONFIG_SERIAL_8250_FSL=y +CONFIG_SERIAL_8250_NR_UARTS=1 +CONFIG_SERIAL_8250_RUNTIME_UARTS=0 +CONFIG_SERIAL_8250_SHARE_IRQ=y +CONFIG_SERIAL_AMBA_PL011=y +CONFIG_SERIAL_AMBA_PL011_CONSOLE=y +CONFIG_SERIAL_DEV_BUS=y +# CONFIG_SERIAL_DEV_CTRL_TTYPORT is not set +CONFIG_SERIAL_MCTRL_GPIO=y +CONFIG_SERIAL_OF_PLATFORM=y +CONFIG_SG_POOL=y +CONFIG_SMP=y +CONFIG_SPARSEMEM=y +CONFIG_SPARSEMEM_EXTREME=y +CONFIG_SPARSEMEM_MANUAL=y +CONFIG_SPARSEMEM_VMEMMAP=y +CONFIG_SPARSEMEM_VMEMMAP_ENABLE=y +CONFIG_SPARSE_IRQ=y +CONFIG_SRCU=y +# CONFIG_STRIP_ASM_SYMS is not set +CONFIG_SUSPEND=y +CONFIG_SUSPEND_FREEZER=y +CONFIG_SWIOTLB=y +CONFIG_SWPHY=y +CONFIG_SYSCTL_EXCEPTION_TRACE=y +CONFIG_SYS_SUPPORTS_HUGETLBFS=y +# CONFIG_TEXTSEARCH is not set +CONFIG_THERMAL=y +CONFIG_THERMAL_DEFAULT_GOV_STEP_WISE=y +CONFIG_THERMAL_EMERGENCY_POWEROFF_DELAY_MS=0 +CONFIG_THERMAL_GOV_STEP_WISE=y +CONFIG_THERMAL_OF=y +CONFIG_THERMAL_WRITABLE_TRIPS=y +CONFIG_THREAD_INFO_IN_TASK=y +CONFIG_TICK_CPU_ACCOUNTING=y +CONFIG_TIMER_OF=y +CONFIG_TIMER_PROBE=y +CONFIG_TMPFS_POSIX_ACL=y +CONFIG_TREE_RCU=y +CONFIG_TREE_SRCU=y +CONFIG_UEVENT_HELPER_PATH="" +CONFIG_UNMAP_KERNEL_AT_EL0=y +CONFIG_USB=y +CONFIG_USB_ANNOUNCE_NEW_DEVICES=y +CONFIG_USB_COMMON=y +CONFIG_USB_DWCOTG=y +# CONFIG_USB_ETH is not set +CONFIG_USB_GADGET=y +CONFIG_USB_PCI=y +CONFIG_USB_PHY=y +CONFIG_USB_STORAGE=y +CONFIG_USB_SUPPORT=y +CONFIG_USB_UAS=y +# CONFIG_USB_UHCI_HCD is not set +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_PCI=y +CONFIG_USB_XHCI_PLATFORM=y +CONFIG_VMAP_STACK=y +CONFIG_VT=y +CONFIG_VT_CONSOLE=y +CONFIG_VT_CONSOLE_SLEEP=y +CONFIG_VT_HW_CONSOLE_BINDING=y +CONFIG_WATCHDOG_CORE=y +CONFIG_XPS=y +CONFIG_XZ_DEC_ARM=y +CONFIG_XZ_DEC_BCJ=y +CONFIG_ZONE_DMA32=y diff --git a/target/linux/bcm27xx/modules/sound.mk b/target/linux/bcm27xx/modules/sound.mk index dab31d8132..5073e5ff50 100644 --- a/target/linux/bcm27xx/modules/sound.mk +++ b/target/linux/bcm27xx/modules/sound.mk @@ -365,6 +365,26 @@ endef $(eval $(call KernelPackage,sound-soc-audioinjector-pi-soundcard)) +define KernelPackage/sound-soc-chipdip-dac + TITLE:=Support for ChipDip DAC + KCONFIG:= \ + CONFIG_SND_BCM2708_SOC_CHIPDIP_DAC + FILES:= \ + $(LINUX_DIR)/sound/soc/bcm/snd-soc-chipdip-dac.ko + AUTOLOAD:=$(call AutoLoad,68,snd-soc-chipdip-dac) + DEPENDS:= \ + kmod-sound-soc-bcm2835-i2s \ + @LINUX_5_10 + $(call AddDepends/sound) +endef + +define KernelPackage/sound-soc-chipdip-dac/description + This package contains support for ChipDip DAC +endef + +$(eval $(call KernelPackage,sound-soc-chipdip-dac)) + + define KernelPackage/sound-soc-digidac1-soundcard TITLE:=Support for RRA DigiDAC1 KCONFIG:= \ diff --git a/target/linux/bcm27xx/modules/video.mk b/target/linux/bcm27xx/modules/video.mk index 2eff4a45d5..f480831caf 100644 --- a/target/linux/bcm27xx/modules/video.mk +++ b/target/linux/bcm27xx/modules/video.mk @@ -6,7 +6,9 @@ define KernelPackage/camera-bcm2835 TITLE:=BCM2835 Camera KCONFIG:= \ CONFIG_VIDEO_BCM2835 \ - CONFIG_VIDEO_BCM2835_MMAL + CONFIG_VIDEO_BCM2835_MMAL \ + CONFIG_VIDEO_BCM2835_UNICAM=n \ + CONFIG_VIDEO_ISP_BCM2835=n FILES:= \ $(LINUX_DIR)/drivers/staging/vc04_services/bcm2835-camera/bcm2835-v4l2.ko AUTOLOAD:=$(call AutoLoad,65,bcm2835-v4l2) @@ -31,12 +33,14 @@ define KernelPackage/drm-vc4 KCONFIG:= \ CONFIG_DRM_VC4 \ CONFIG_DRM_VC4_HDMI_CEC=y \ + CONFIG_DRM_GUD=n \ CONFIG_DRM_V3D=n \ CONFIG_DRM_TVE200=n FILES:= \ $(LINUX_DIR)/drivers/gpu/drm/vc4/vc4.ko \ $(LINUX_DIR)/drivers/gpu/drm/drm_kms_helper.ko \ - $(LINUX_DIR)/drivers/media/cec/cec.ko + $(LINUX_DIR)/drivers/media/cec/cec.ko@lt5.10 \ + $(LINUX_DIR)/drivers/media/cec/core/cec.ko@ge5.10 AUTOLOAD:=$(call AutoProbe,vc4) endef diff --git a/target/linux/bcm27xx/patches-5.10/950-0001-arm-partially-revert-702b94bff3c50542a6e4ab9a4f4cef0.patch b/target/linux/bcm27xx/patches-5.10/950-0001-arm-partially-revert-702b94bff3c50542a6e4ab9a4f4cef0.patch new file mode 100644 index 0000000000..87c90f8c16 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0001-arm-partially-revert-702b94bff3c50542a6e4ab9a4f4cef0.patch @@ -0,0 +1,99 @@ +From c966ee565b122d840d7aac4c07c53b0d679d2d33 Mon Sep 17 00:00:00 2001 +From: Dan Pasanen +Date: Thu, 21 Sep 2017 09:55:42 -0500 +Subject: [PATCH] arm: partially revert + 702b94bff3c50542a6e4ab9a4f4cef093262fe65 + +* Re-expose some dmi APIs for use in VCSM +--- + arch/arm/include/asm/cacheflush.h | 21 +++++++++++++++++++++ + arch/arm/include/asm/glue-cache.h | 2 ++ + arch/arm/mm/proc-macros.S | 2 ++ + arch/arm/mm/proc-syms.c | 3 +++ + 4 files changed, 28 insertions(+) + +--- a/arch/arm/include/asm/cacheflush.h ++++ b/arch/arm/include/asm/cacheflush.h +@@ -91,6 +91,21 @@ + * DMA Cache Coherency + * =================== + * ++ * dma_inv_range(start, end) ++ * ++ * Invalidate (discard) the specified virtual address range. ++ * May not write back any entries. If 'start' or 'end' ++ * are not cache line aligned, those lines must be written ++ * back. ++ * - start - virtual start address ++ * - end - virtual end address ++ * ++ * dma_clean_range(start, end) ++ * ++ * Clean (write back) the specified virtual address range. ++ * - start - virtual start address ++ * - end - virtual end address ++ * + * dma_flush_range(start, end) + * + * Clean and invalidate the specified virtual address range. +@@ -112,6 +127,8 @@ struct cpu_cache_fns { + void (*dma_map_area)(const void *, size_t, int); + void (*dma_unmap_area)(const void *, size_t, int); + ++ void (*dma_inv_range)(const void *, const void *); ++ void (*dma_clean_range)(const void *, const void *); + void (*dma_flush_range)(const void *, const void *); + } __no_randomize_layout; + +@@ -137,6 +154,8 @@ extern struct cpu_cache_fns cpu_cache; + * is visible to DMA, or data written by DMA to system memory is + * visible to the CPU. + */ ++#define dmac_inv_range cpu_cache.dma_inv_range ++#define dmac_clean_range cpu_cache.dma_clean_range + #define dmac_flush_range cpu_cache.dma_flush_range + + #else +@@ -156,6 +175,8 @@ extern void __cpuc_flush_dcache_area(voi + * is visible to DMA, or data written by DMA to system memory is + * visible to the CPU. + */ ++extern void dmac_inv_range(const void *, const void *); ++extern void dmac_clean_range(const void *, const void *); + extern void dmac_flush_range(const void *, const void *); + + #endif +--- a/arch/arm/include/asm/glue-cache.h ++++ b/arch/arm/include/asm/glue-cache.h +@@ -155,6 +155,8 @@ static inline void nop_dma_unmap_area(co + #define __cpuc_coherent_user_range __glue(_CACHE,_coherent_user_range) + #define __cpuc_flush_dcache_area __glue(_CACHE,_flush_kern_dcache_area) + ++#define dmac_inv_range __glue(_CACHE,_dma_inv_range) ++#define dmac_clean_range __glue(_CACHE,_dma_clean_range) + #define dmac_flush_range __glue(_CACHE,_dma_flush_range) + #endif + +--- a/arch/arm/mm/proc-macros.S ++++ b/arch/arm/mm/proc-macros.S +@@ -334,6 +334,8 @@ ENTRY(\name\()_cache_fns) + .long \name\()_flush_kern_dcache_area + .long \name\()_dma_map_area + .long \name\()_dma_unmap_area ++ .long \name\()_dma_inv_range ++ .long \name\()_dma_clean_range + .long \name\()_dma_flush_range + .size \name\()_cache_fns, . - \name\()_cache_fns + .endm +--- a/arch/arm/mm/proc-syms.c ++++ b/arch/arm/mm/proc-syms.c +@@ -27,6 +27,9 @@ EXPORT_SYMBOL(__cpuc_flush_user_all); + EXPORT_SYMBOL(__cpuc_flush_user_range); + EXPORT_SYMBOL(__cpuc_coherent_kern_range); + EXPORT_SYMBOL(__cpuc_flush_dcache_area); ++EXPORT_SYMBOL(dmac_inv_range); ++EXPORT_SYMBOL(dmac_clean_range); ++EXPORT_SYMBOL(dmac_flush_range); + #else + EXPORT_SYMBOL(cpu_cache); + #endif diff --git a/target/linux/bcm27xx/patches-5.10/950-0002-Revert-rtc-pcf8523-properly-handle-oscillator-stop-b.patch b/target/linux/bcm27xx/patches-5.10/950-0002-Revert-rtc-pcf8523-properly-handle-oscillator-stop-b.patch new file mode 100644 index 0000000000..3e26f97313 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0002-Revert-rtc-pcf8523-properly-handle-oscillator-stop-b.patch @@ -0,0 +1,56 @@ +From f4888774b6bf2f68fa2b389690eee07d7e8efdb9 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 29 Oct 2018 14:45:45 +0000 +Subject: [PATCH] Revert "rtc: pcf8523: properly handle oscillator stop + bit" + +This reverts commit ede44c908d44b166a5b6bd7caacd105c2ff5a70f. + +See: https://github.com/raspberrypi/firmware/issues/1065 + +Signed-off-by: Phil Elwell +--- + drivers/rtc/rtc-pcf8523.c | 25 ++++++++++++++++++++++--- + 1 file changed, 22 insertions(+), 3 deletions(-) + +--- a/drivers/rtc/rtc-pcf8523.c ++++ b/drivers/rtc/rtc-pcf8523.c +@@ -205,8 +205,28 @@ static int pcf8523_rtc_read_time(struct + if (err < 0) + return err; + +- if (regs[0] & REG_SECONDS_OS) +- return -EINVAL; ++ if (regs[0] & REG_SECONDS_OS) { ++ /* ++ * If the oscillator was stopped, try to clear the flag. Upon ++ * power-up the flag is always set, but if we cannot clear it ++ * the oscillator isn't running properly for some reason. The ++ * sensible thing therefore is to return an error, signalling ++ * that the clock cannot be assumed to be correct. ++ */ ++ ++ regs[0] &= ~REG_SECONDS_OS; ++ ++ err = pcf8523_write(client, REG_SECONDS, regs[0]); ++ if (err < 0) ++ return err; ++ ++ err = pcf8523_read(client, REG_SECONDS, ®s[0]); ++ if (err < 0) ++ return err; ++ ++ if (regs[0] & REG_SECONDS_OS) ++ return -EAGAIN; ++ } + + tm->tm_sec = bcd2bin(regs[0] & 0x7f); + tm->tm_min = bcd2bin(regs[1] & 0x7f); +@@ -242,7 +262,6 @@ static int pcf8523_rtc_set_time(struct d + return err; + + regs[0] = REG_SECONDS; +- /* This will purposely overwrite REG_SECONDS_OS */ + regs[1] = bin2bcd(tm->tm_sec); + regs[2] = bin2bcd(tm->tm_min); + regs[3] = bin2bcd(tm->tm_hour); diff --git a/target/linux/bcm27xx/patches-5.10/950-0003-Revert-staging-bcm2835-audio-Drop-DT-dependency.patch b/target/linux/bcm27xx/patches-5.10/950-0003-Revert-staging-bcm2835-audio-Drop-DT-dependency.patch new file mode 100644 index 0000000000..97b7ee0d9c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0003-Revert-staging-bcm2835-audio-Drop-DT-dependency.patch @@ -0,0 +1,96 @@ +From 2aa4bd3751f6792bf00d59e4d9cd8a5550872cdb Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Fri, 15 Mar 2019 21:11:10 +0000 +Subject: [PATCH] Revert "staging: bcm2835-audio: Drop DT dependency" + +This reverts commit b7491a9fca2dc2535b9dc922550a37c5baae9d3d. +--- + .../vc04_services/bcm2835-audio/bcm2835.c | 31 +++++++++++++------ + 1 file changed, 22 insertions(+), 9 deletions(-) + +--- a/drivers/staging/vc04_services/bcm2835-audio/bcm2835.c ++++ b/drivers/staging/vc04_services/bcm2835-audio/bcm2835.c +@@ -6,13 +6,13 @@ + #include + #include + #include ++#include + + #include "bcm2835.h" + + static bool enable_hdmi; + static bool enable_headphones; + static bool enable_compat_alsa = true; +-static int num_channels = MAX_SUBSTREAMS; + + module_param(enable_hdmi, bool, 0444); + MODULE_PARM_DESC(enable_hdmi, "Enables HDMI virtual audio device"); +@@ -21,8 +21,6 @@ MODULE_PARM_DESC(enable_headphones, "Ena + module_param(enable_compat_alsa, bool, 0444); + MODULE_PARM_DESC(enable_compat_alsa, + "Enables ALSA compatibility virtual audio device"); +-module_param(num_channels, int, 0644); +-MODULE_PARM_DESC(num_channels, "Number of audio channels (default: 8)"); + + static void bcm2835_devm_free_vchi_ctx(struct device *dev, void *res) + { +@@ -296,19 +294,28 @@ static int snd_add_child_devices(struct + static int snd_bcm2835_alsa_probe(struct platform_device *pdev) + { + struct device *dev = &pdev->dev; ++ u32 numchans; + int err; + +- if (num_channels <= 0 || num_channels > MAX_SUBSTREAMS) { +- num_channels = MAX_SUBSTREAMS; +- dev_warn(dev, "Illegal num_channels value, will use %u\n", +- num_channels); ++ err = of_property_read_u32(dev->of_node, "brcm,pwm-channels", ++ &numchans); ++ if (err) { ++ dev_err(dev, "Failed to get DT property 'brcm,pwm-channels'"); ++ return err; ++ } ++ ++ if (numchans == 0 || numchans > MAX_SUBSTREAMS) { ++ numchans = MAX_SUBSTREAMS; ++ dev_warn(dev, ++ "Illegal 'brcm,pwm-channels' value, will use %u\n", ++ numchans); + } + + err = bcm2835_devm_add_vchi_ctx(dev); + if (err) + return err; + +- err = snd_add_child_devices(dev, num_channels); ++ err = snd_add_child_devices(dev, numchans); + if (err) + return err; + +@@ -330,6 +337,12 @@ static int snd_bcm2835_alsa_resume(struc + + #endif + ++static const struct of_device_id snd_bcm2835_of_match_table[] = { ++ { .compatible = "brcm,bcm2835-audio",}, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, snd_bcm2835_of_match_table); ++ + static struct platform_driver bcm2835_alsa_driver = { + .probe = snd_bcm2835_alsa_probe, + #ifdef CONFIG_PM +@@ -338,6 +351,7 @@ static struct platform_driver bcm2835_al + #endif + .driver = { + .name = "bcm2835_audio", ++ .of_match_table = snd_bcm2835_of_match_table, + }, + }; + module_platform_driver(bcm2835_alsa_driver); +@@ -345,4 +359,3 @@ module_platform_driver(bcm2835_alsa_driv + MODULE_AUTHOR("Dom Cobley"); + MODULE_DESCRIPTION("Alsa driver for BCM2835 chip"); + MODULE_LICENSE("GPL"); +-MODULE_ALIAS("platform:bcm2835_audio"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0004-Revert-spi-spidev-Fix-CS-polarity-if-GPIO-descriptor.patch b/target/linux/bcm27xx/patches-5.10/950-0004-Revert-spi-spidev-Fix-CS-polarity-if-GPIO-descriptor.patch new file mode 100644 index 0000000000..012ff54aa3 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0004-Revert-spi-spidev-Fix-CS-polarity-if-GPIO-descriptor.patch @@ -0,0 +1,32 @@ +From 086a38a1e0eea3b7cbb207384b92d5dc82c62454 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 20 Apr 2020 13:41:10 +0100 +Subject: [PATCH] Revert "spi: spidev: Fix CS polarity if GPIO + descriptors are used" + +This reverts commit 83b2a8fe43bda0c11981ad6afa5dd0104d78be28. +--- + drivers/spi/spidev.c | 5 ----- + 1 file changed, 5 deletions(-) + +--- a/drivers/spi/spidev.c ++++ b/drivers/spi/spidev.c +@@ -402,7 +402,6 @@ spidev_ioctl(struct file *filp, unsigned + else + retval = get_user(tmp, (u32 __user *)arg); + if (retval == 0) { +- struct spi_controller *ctlr = spi->controller; + u32 save = spi->mode; + + if (tmp & ~SPI_MODE_MASK) { +@@ -410,10 +409,6 @@ spidev_ioctl(struct file *filp, unsigned + break; + } + +- if (ctlr->use_gpio_descriptors && ctlr->cs_gpiods && +- ctlr->cs_gpiods[spi->chip_select]) +- tmp |= SPI_CS_HIGH; +- + tmp |= spi->mode & ~SPI_MODE_MASK; + spi->mode = (u16)tmp; + retval = spi_setup(spi); diff --git a/target/linux/bcm27xx/patches-5.10/950-0005-Revert-mailbox-avoid-timer-start-from-callback.patch b/target/linux/bcm27xx/patches-5.10/950-0005-Revert-mailbox-avoid-timer-start-from-callback.patch new file mode 100644 index 0000000000..5ec683ff6a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0005-Revert-mailbox-avoid-timer-start-from-callback.patch @@ -0,0 +1,58 @@ +From a8fb0d43b8acd25d68a0d2c24fd0260393148447 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 3 Nov 2020 11:49:53 +0000 +Subject: [PATCH] Revert "mailbox: avoid timer start from callback" + +This reverts commit c7dacf5b0f32957b24ef29df1207dc2cd8307743. + +The Pi 400 shutdown/poweroff mechanism relies on being able to set +a GPIO on the expander in the pm_power_off handler, something that +requires two mailbox calls - GET_GPIO_STATE and SET_GPIO_STATE. A +recent kernel change introduces a reasonable possibility that the +GET call doesn't completes, and bisecting led to a commit from +October that changes the timer usage of the mailbox. + +My theory is that there is a race condition in the new code that breaks +the poll timer, but that it normally goes unnoticed because subsequent +mailbox activity wakes it up again. The power-off mailbox calls happen +at a time when other subsystems have been shut down, so if one of them +fails then there is nothing to allow it to recover. + +See: https://github.com/raspberrypi/linux/issues/3941 + +Signed-off-by: Phil Elwell +--- + drivers/mailbox/mailbox.c | 12 +++++------- + 1 file changed, 5 insertions(+), 7 deletions(-) + +--- a/drivers/mailbox/mailbox.c ++++ b/drivers/mailbox/mailbox.c +@@ -82,12 +82,9 @@ static void msg_submit(struct mbox_chan + exit: + spin_unlock_irqrestore(&chan->lock, flags); + +- /* kick start the timer immediately to avoid delays */ +- if (!err && (chan->txdone_method & TXDONE_BY_POLL)) { +- /* but only if not already active */ +- if (!hrtimer_active(&chan->mbox->poll_hrt)) +- hrtimer_start(&chan->mbox->poll_hrt, 0, HRTIMER_MODE_REL); +- } ++ if (!err && (chan->txdone_method & TXDONE_BY_POLL)) ++ /* kick start the timer immediately to avoid delays */ ++ hrtimer_start(&chan->mbox->poll_hrt, 0, HRTIMER_MODE_REL); + } + + static void tx_tick(struct mbox_chan *chan, int r) +@@ -125,10 +122,11 @@ static enum hrtimer_restart txdone_hrtim + struct mbox_chan *chan = &mbox->chans[i]; + + if (chan->active_req && chan->cl) { +- resched = true; + txdone = chan->mbox->ops->last_tx_done(chan); + if (txdone) + tx_tick(chan, 0); ++ else ++ resched = true; + } + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0006-smsx95xx-fix-crimes-against-truesize.patch b/target/linux/bcm27xx/patches-5.10/950-0006-smsx95xx-fix-crimes-against-truesize.patch new file mode 100644 index 0000000000..163dd76e1c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0006-smsx95xx-fix-crimes-against-truesize.patch @@ -0,0 +1,47 @@ +From dbfae4876cd4c8525a0100f19307f16cf7fb384a Mon Sep 17 00:00:00 2001 +From: Steve Glendinning +Date: Thu, 19 Feb 2015 18:47:12 +0000 +Subject: [PATCH] smsx95xx: fix crimes against truesize + +smsc95xx is adjusting truesize when it shouldn't, and following a recent patch from Eric this is now triggering warnings. + +This patch stops smsc95xx from changing truesize. + +Signed-off-by: Steve Glendinning +--- + drivers/net/usb/smsc95xx.c | 10 ++++++++-- + 1 file changed, 8 insertions(+), 2 deletions(-) + +--- a/drivers/net/usb/smsc95xx.c ++++ b/drivers/net/usb/smsc95xx.c +@@ -67,6 +67,10 @@ static bool turbo_mode = true; + module_param(turbo_mode, bool, 0644); + MODULE_PARM_DESC(turbo_mode, "Enable multiple frames per Rx transaction"); + ++static bool truesize_mode = false; ++module_param(truesize_mode, bool, 0644); ++MODULE_PARM_DESC(truesize_mode, "Report larger truesize value"); ++ + static int __must_check __smsc95xx_read_reg(struct usbnet *dev, u32 index, + u32 *data, int in_pm) + { +@@ -1827,7 +1831,8 @@ static int smsc95xx_rx_fixup(struct usbn + if (dev->net->features & NETIF_F_RXCSUM) + smsc95xx_rx_csum_offload(skb); + skb_trim(skb, skb->len - 4); /* remove fcs */ +- skb->truesize = size + sizeof(struct sk_buff); ++ if (truesize_mode) ++ skb->truesize = size + sizeof(struct sk_buff); + + return 1; + } +@@ -1845,7 +1850,8 @@ static int smsc95xx_rx_fixup(struct usbn + if (dev->net->features & NETIF_F_RXCSUM) + smsc95xx_rx_csum_offload(ax_skb); + skb_trim(ax_skb, ax_skb->len - 4); /* remove fcs */ +- ax_skb->truesize = size + sizeof(struct sk_buff); ++ if (truesize_mode) ++ ax_skb->truesize = size + sizeof(struct sk_buff); + + usbnet_skb_return(dev, ax_skb); + } diff --git a/target/linux/bcm27xx/patches-5.10/950-0007-smsc95xx-Experimental-Enable-turbo_mode-and-packetsi.patch b/target/linux/bcm27xx/patches-5.10/950-0007-smsc95xx-Experimental-Enable-turbo_mode-and-packetsi.patch new file mode 100644 index 0000000000..025b052333 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0007-smsc95xx-Experimental-Enable-turbo_mode-and-packetsi.patch @@ -0,0 +1,43 @@ +From 5792c081bb959c57b381439e40d07c919193a993 Mon Sep 17 00:00:00 2001 +From: Sam Nazarko +Date: Fri, 1 Apr 2016 17:27:21 +0100 +Subject: [PATCH] smsc95xx: Experimental: Enable turbo_mode and + packetsize=2560 by default + +See: http://forum.kodi.tv/showthread.php?tid=285288 +--- + drivers/net/usb/smsc95xx.c | 14 +++++++++----- + 1 file changed, 9 insertions(+), 5 deletions(-) + +--- a/drivers/net/usb/smsc95xx.c ++++ b/drivers/net/usb/smsc95xx.c +@@ -71,6 +71,10 @@ static bool truesize_mode = false; + module_param(truesize_mode, bool, 0644); + MODULE_PARM_DESC(truesize_mode, "Report larger truesize value"); + ++static int packetsize = 2560; ++module_param(packetsize, int, 0644); ++MODULE_PARM_DESC(packetsize, "Override the RX URB packet size"); ++ + static int __must_check __smsc95xx_read_reg(struct usbnet *dev, u32 index, + u32 *data, int in_pm) + { +@@ -905,13 +909,13 @@ static int smsc95xx_reset(struct usbnet + + if (!turbo_mode) { + burst_cap = 0; +- dev->rx_urb_size = MAX_SINGLE_PACKET_SIZE; ++ dev->rx_urb_size = packetsize ? packetsize : MAX_SINGLE_PACKET_SIZE; + } else if (dev->udev->speed == USB_SPEED_HIGH) { +- burst_cap = DEFAULT_HS_BURST_CAP_SIZE / HS_USB_PKT_SIZE; +- dev->rx_urb_size = DEFAULT_HS_BURST_CAP_SIZE; ++ dev->rx_urb_size = packetsize ? packetsize : DEFAULT_HS_BURST_CAP_SIZE; ++ burst_cap = dev->rx_urb_size / HS_USB_PKT_SIZE; + } else { +- burst_cap = DEFAULT_FS_BURST_CAP_SIZE / FS_USB_PKT_SIZE; +- dev->rx_urb_size = DEFAULT_FS_BURST_CAP_SIZE; ++ dev->rx_urb_size = packetsize ? packetsize : DEFAULT_FS_BURST_CAP_SIZE; ++ burst_cap = dev->rx_urb_size / FS_USB_PKT_SIZE; + } + + netif_dbg(dev, ifup, dev->net, "rx_urb_size=%ld\n", diff --git a/target/linux/bcm27xx/patches-5.10/950-0008-Allow-mac-address-to-be-set-in-smsc95xx.patch b/target/linux/bcm27xx/patches-5.10/950-0008-Allow-mac-address-to-be-set-in-smsc95xx.patch new file mode 100644 index 0000000000..1cf4d21a57 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0008-Allow-mac-address-to-be-set-in-smsc95xx.patch @@ -0,0 +1,96 @@ +From a5e86e4e7cc86e6a24844d758d2258c8b23f18f0 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Tue, 26 Mar 2013 17:26:38 +0000 +Subject: [PATCH] Allow mac address to be set in smsc95xx + +Signed-off-by: popcornmix +--- + drivers/net/usb/smsc95xx.c | 56 ++++++++++++++++++++++++++++++++++++++ + 1 file changed, 56 insertions(+) + +--- a/drivers/net/usb/smsc95xx.c ++++ b/drivers/net/usb/smsc95xx.c +@@ -50,6 +50,7 @@ + #define SUSPEND_SUSPEND3 (0x08) + #define SUSPEND_ALLMODES (SUSPEND_SUSPEND0 | SUSPEND_SUSPEND1 | \ + SUSPEND_SUSPEND2 | SUSPEND_SUSPEND3) ++#define MAC_ADDR_LEN (6) + + struct smsc95xx_priv { + u32 mac_cr; +@@ -75,6 +76,10 @@ static int packetsize = 2560; + module_param(packetsize, int, 0644); + MODULE_PARM_DESC(packetsize, "Override the RX URB packet size"); + ++static char *macaddr = ":"; ++module_param(macaddr, charp, 0); ++MODULE_PARM_DESC(macaddr, "MAC address"); ++ + static int __must_check __smsc95xx_read_reg(struct usbnet *dev, u32 index, + u32 *data, int in_pm) + { +@@ -761,6 +766,53 @@ static int smsc95xx_ioctl(struct net_dev + return phy_mii_ioctl(netdev->phydev, rq, cmd); + } + ++/* Check the macaddr module parameter for a MAC address */ ++static int smsc95xx_is_macaddr_param(struct usbnet *dev, u8 *dev_mac) ++{ ++ int i, j, got_num, num; ++ u8 mtbl[MAC_ADDR_LEN]; ++ ++ if (macaddr[0] == ':') ++ return 0; ++ ++ i = 0; ++ j = 0; ++ num = 0; ++ got_num = 0; ++ while (j < MAC_ADDR_LEN) { ++ if (macaddr[i] && macaddr[i] != ':') { ++ got_num++; ++ if ('0' <= macaddr[i] && macaddr[i] <= '9') ++ num = num * 16 + macaddr[i] - '0'; ++ else if ('A' <= macaddr[i] && macaddr[i] <= 'F') ++ num = num * 16 + 10 + macaddr[i] - 'A'; ++ else if ('a' <= macaddr[i] && macaddr[i] <= 'f') ++ num = num * 16 + 10 + macaddr[i] - 'a'; ++ else ++ break; ++ i++; ++ } else if (got_num == 2) { ++ mtbl[j++] = (u8) num; ++ num = 0; ++ got_num = 0; ++ i++; ++ } else { ++ break; ++ } ++ } ++ ++ if (j == MAC_ADDR_LEN) { ++ netif_dbg(dev, ifup, dev->net, "Overriding MAC address with: " ++ "%02x:%02x:%02x:%02x:%02x:%02x\n", mtbl[0], mtbl[1], mtbl[2], ++ mtbl[3], mtbl[4], mtbl[5]); ++ for (i = 0; i < MAC_ADDR_LEN; i++) ++ dev_mac[i] = mtbl[i]; ++ return 1; ++ } else { ++ return 0; ++ } ++} ++ + static void smsc95xx_init_mac_address(struct usbnet *dev) + { + /* maybe the boot loader passed the MAC address in devicetree */ +@@ -783,6 +835,10 @@ static void smsc95xx_init_mac_address(st + } + } + ++ /* Check module parameters */ ++ if (smsc95xx_is_macaddr_param(dev, dev->net->dev_addr)) ++ return; ++ + /* no useful static MAC address found. generate a random one */ + eth_hw_addr_random(dev->net); + netif_dbg(dev, ifup, dev->net, "MAC address set to eth_random_addr\n"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0009-Protect-__release_resource-against-resources-without.patch b/target/linux/bcm27xx/patches-5.10/950-0009-Protect-__release_resource-against-resources-without.patch new file mode 100644 index 0000000000..db51c15cd8 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0009-Protect-__release_resource-against-resources-without.patch @@ -0,0 +1,28 @@ +From f146f2bb597fe00b6c2e5da169a766dc8ab2a4fa Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 13 Mar 2015 12:43:36 +0000 +Subject: [PATCH] Protect __release_resource against resources without + parents + +Without this patch, removing a device tree overlay can crash here. + +Signed-off-by: Phil Elwell +--- + kernel/resource.c | 6 ++++++ + 1 file changed, 6 insertions(+) + +--- a/kernel/resource.c ++++ b/kernel/resource.c +@@ -214,6 +214,12 @@ static int __release_resource(struct res + { + struct resource *tmp, **p, *chd; + ++ if (!old->parent) { ++ WARN(old->sibling, "sibling but no parent"); ++ if (old->sibling) ++ return -EINVAL; ++ return 0; ++ } + p = &old->parent->child; + for (;;) { + tmp = *p; diff --git a/target/linux/bcm27xx/patches-5.10/950-0010-irq-bcm2836-Avoid-Invalid-trigger-warning.patch b/target/linux/bcm27xx/patches-5.10/950-0010-irq-bcm2836-Avoid-Invalid-trigger-warning.patch new file mode 100644 index 0000000000..3a611e0919 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0010-irq-bcm2836-Avoid-Invalid-trigger-warning.patch @@ -0,0 +1,24 @@ +From 55a3a6691b480c57613f9db3a0e1aca02b7f68c1 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 9 Feb 2017 14:33:30 +0000 +Subject: [PATCH] irq-bcm2836: Avoid "Invalid trigger warning" + +Initialise the level for each IRQ to avoid a warning from the +arm arch timer code. + +Signed-off-by: Phil Elwell +--- + drivers/irqchip/irq-bcm2836.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/irqchip/irq-bcm2836.c ++++ b/drivers/irqchip/irq-bcm2836.c +@@ -128,7 +128,7 @@ static int bcm2836_map(struct irq_domain + irq_set_percpu_devid(irq); + irq_domain_set_info(d, irq, hw, chip, d->host_data, + handle_percpu_devid_irq, NULL, NULL); +- irq_set_status_flags(irq, IRQ_NOAUTOEN); ++ irq_set_status_flags(irq, IRQ_NOAUTOEN | IRQ_TYPE_LEVEL_LOW); + + return 0; + } diff --git a/target/linux/bcm27xx/patches-5.10/950-0011-irqchip-bcm2835-Add-FIQ-support.patch b/target/linux/bcm27xx/patches-5.10/950-0011-irqchip-bcm2835-Add-FIQ-support.patch new file mode 100644 index 0000000000..95a4819ae1 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0011-irqchip-bcm2835-Add-FIQ-support.patch @@ -0,0 +1,127 @@ +From ad12646921360036adf7ecdcf1325b9a880b316a Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= +Date: Fri, 12 Jun 2015 19:01:05 +0200 +Subject: [PATCH] irqchip: bcm2835: Add FIQ support +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Add a duplicate irq range with an offset on the hwirq's so the +driver can detect that enable_fiq() is used. +Tested with downstream dwc_otg USB controller driver. + +Signed-off-by: Noralf Trønnes +Reviewed-by: Eric Anholt +Acked-by: Stephen Warren +--- + arch/arm/mach-bcm/Kconfig | 1 + + drivers/irqchip/irq-bcm2835.c | 51 +++++++++++++++++++++++++++++++---- + 2 files changed, 47 insertions(+), 5 deletions(-) + +--- a/arch/arm/mach-bcm/Kconfig ++++ b/arch/arm/mach-bcm/Kconfig +@@ -161,6 +161,7 @@ config ARCH_BCM2835 + select ARM_TIMER_SP804 + select HAVE_ARM_ARCH_TIMER if ARCH_MULTI_V7 + select BCM2835_TIMER ++ select FIQ + select PINCTRL + select PINCTRL_BCM2835 + select MFD_CORE +--- a/drivers/irqchip/irq-bcm2835.c ++++ b/drivers/irqchip/irq-bcm2835.c +@@ -45,7 +45,7 @@ + #include + + /* Put the bank and irq (32 bits) into the hwirq */ +-#define MAKE_HWIRQ(b, n) ((b << 5) | (n)) ++#define MAKE_HWIRQ(b, n) (((b) << 5) | (n)) + #define HWIRQ_BANK(i) (i >> 5) + #define HWIRQ_BIT(i) BIT(i & 0x1f) + +@@ -62,9 +62,13 @@ + + #define REG_FIQ_CONTROL 0x0c + #define FIQ_CONTROL_ENABLE BIT(7) ++#define REG_FIQ_ENABLE FIQ_CONTROL_ENABLE ++#define REG_FIQ_DISABLE 0 + + #define NR_BANKS 3 + #define IRQS_PER_BANK 32 ++#define NUMBER_IRQS MAKE_HWIRQ(NR_BANKS, 0) ++#define FIQ_START (NR_IRQS_BANK0 + MAKE_HWIRQ(NR_BANKS - 1, 0)) + + static const int reg_pending[] __initconst = { 0x00, 0x04, 0x08 }; + static const int reg_enable[] __initconst = { 0x18, 0x10, 0x14 }; +@@ -89,14 +93,38 @@ static void __exception_irq_entry bcm283 + struct pt_regs *regs); + static void bcm2836_chained_handle_irq(struct irq_desc *desc); + ++static inline unsigned int hwirq_to_fiq(unsigned long hwirq) ++{ ++ hwirq -= NUMBER_IRQS; ++ /* ++ * The hwirq numbering used in this driver is: ++ * BASE (0-7) GPU1 (32-63) GPU2 (64-95). ++ * This differ from the one used in the FIQ register: ++ * GPU1 (0-31) GPU2 (32-63) BASE (64-71) ++ */ ++ if (hwirq >= 32) ++ return hwirq - 32; ++ ++ return hwirq + 64; ++} ++ + static void armctrl_mask_irq(struct irq_data *d) + { +- writel_relaxed(HWIRQ_BIT(d->hwirq), intc.disable[HWIRQ_BANK(d->hwirq)]); ++ if (d->hwirq >= NUMBER_IRQS) ++ writel_relaxed(REG_FIQ_DISABLE, intc.base + REG_FIQ_CONTROL); ++ else ++ writel_relaxed(HWIRQ_BIT(d->hwirq), ++ intc.disable[HWIRQ_BANK(d->hwirq)]); + } + + static void armctrl_unmask_irq(struct irq_data *d) + { +- writel_relaxed(HWIRQ_BIT(d->hwirq), intc.enable[HWIRQ_BANK(d->hwirq)]); ++ if (d->hwirq >= NUMBER_IRQS) ++ writel_relaxed(REG_FIQ_ENABLE | hwirq_to_fiq(d->hwirq), ++ intc.base + REG_FIQ_CONTROL); ++ else ++ writel_relaxed(HWIRQ_BIT(d->hwirq), ++ intc.enable[HWIRQ_BANK(d->hwirq)]); + } + + static struct irq_chip armctrl_chip = { +@@ -142,8 +170,9 @@ static int __init armctrl_of_init(struct + if (!base) + panic("%pOF: unable to map IC registers\n", node); + +- intc.domain = irq_domain_add_linear(node, MAKE_HWIRQ(NR_BANKS, 0), +- &armctrl_ops, NULL); ++ intc.base = base; ++ intc.domain = irq_domain_add_linear(node, NUMBER_IRQS * 2, ++ &armctrl_ops, NULL); + if (!intc.domain) + panic("%pOF: unable to create IRQ domain\n", node); + +@@ -186,6 +215,18 @@ static int __init armctrl_of_init(struct + set_handle_irq(bcm2835_handle_irq); + } + ++ /* Make a duplicate irq range which is used to enable FIQ */ ++ for (b = 0; b < NR_BANKS; b++) { ++ for (i = 0; i < bank_irqs[b]; i++) { ++ irq = irq_create_mapping(intc.domain, ++ MAKE_HWIRQ(b, i) + NUMBER_IRQS); ++ BUG_ON(irq <= 0); ++ irq_set_chip(irq, &armctrl_chip); ++ set_irq_flags(irq, IRQF_VALID | IRQF_PROBE); ++ } ++ } ++ init_FIQ(FIQ_START); ++ + return 0; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0012-irqchip-irq-bcm2835-Add-2836-FIQ-support.patch b/target/linux/bcm27xx/patches-5.10/950-0012-irqchip-irq-bcm2835-Add-2836-FIQ-support.patch new file mode 100644 index 0000000000..f8ca67ca2b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0012-irqchip-irq-bcm2835-Add-2836-FIQ-support.patch @@ -0,0 +1,99 @@ +From 18774f96f2766eb711d462842626ae603110c18e Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= +Date: Fri, 23 Oct 2015 16:26:55 +0200 +Subject: [PATCH] irqchip: irq-bcm2835: Add 2836 FIQ support +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: Noralf Trønnes +--- + drivers/irqchip/irq-bcm2835.c | 43 +++++++++++++++++++++++++++++++++-- + 1 file changed, 41 insertions(+), 2 deletions(-) + +--- a/drivers/irqchip/irq-bcm2835.c ++++ b/drivers/irqchip/irq-bcm2835.c +@@ -41,8 +41,11 @@ + #include + #include + #include ++#include ++#include + + #include ++#include + + /* Put the bank and irq (32 bits) into the hwirq */ + #define MAKE_HWIRQ(b, n) (((b) << 5) | (n)) +@@ -60,6 +63,9 @@ + #define BANK0_VALID_MASK (BANK0_HWIRQ_MASK | BANK1_HWIRQ | BANK2_HWIRQ \ + | SHORTCUT1_MASK | SHORTCUT2_MASK) + ++#undef ARM_LOCAL_GPU_INT_ROUTING ++#define ARM_LOCAL_GPU_INT_ROUTING 0x0c ++ + #define REG_FIQ_CONTROL 0x0c + #define FIQ_CONTROL_ENABLE BIT(7) + #define REG_FIQ_ENABLE FIQ_CONTROL_ENABLE +@@ -86,6 +92,7 @@ struct armctrl_ic { + void __iomem *enable[NR_BANKS]; + void __iomem *disable[NR_BANKS]; + struct irq_domain *domain; ++ struct regmap *local_regmap; + }; + + static struct armctrl_ic intc __read_mostly; +@@ -119,12 +126,35 @@ static void armctrl_mask_irq(struct irq_ + + static void armctrl_unmask_irq(struct irq_data *d) + { +- if (d->hwirq >= NUMBER_IRQS) ++ if (d->hwirq >= NUMBER_IRQS) { ++ if (num_online_cpus() > 1) { ++ unsigned int data; ++ int ret; ++ ++ if (!intc.local_regmap) { ++ pr_err("FIQ is disabled due to missing regmap\n"); ++ return; ++ } ++ ++ ret = regmap_read(intc.local_regmap, ++ ARM_LOCAL_GPU_INT_ROUTING, &data); ++ if (ret) { ++ pr_err("Failed to read int routing %d\n", ret); ++ return; ++ } ++ ++ data &= ~0xc; ++ data |= (1 << 2); ++ regmap_write(intc.local_regmap, ++ ARM_LOCAL_GPU_INT_ROUTING, data); ++ } ++ + writel_relaxed(REG_FIQ_ENABLE | hwirq_to_fiq(d->hwirq), + intc.base + REG_FIQ_CONTROL); +- else ++ } else { + writel_relaxed(HWIRQ_BIT(d->hwirq), + intc.enable[HWIRQ_BANK(d->hwirq)]); ++ } + } + + static struct irq_chip armctrl_chip = { +@@ -215,6 +245,15 @@ static int __init armctrl_of_init(struct + set_handle_irq(bcm2835_handle_irq); + } + ++ if (is_2836) { ++ intc.local_regmap = ++ syscon_regmap_lookup_by_compatible("brcm,bcm2836-arm-local"); ++ if (IS_ERR(intc.local_regmap)) { ++ pr_err("Failed to get local register map. FIQ is disabled for cpus > 1\n"); ++ intc.local_regmap = NULL; ++ } ++ } ++ + /* Make a duplicate irq range which is used to enable FIQ */ + for (b = 0; b < NR_BANKS; b++) { + for (i = 0; i < bank_irqs[b]; i++) { diff --git a/target/linux/bcm27xx/patches-5.10/950-0013-spi-spidev-Completely-disable-the-spidev-warning.patch b/target/linux/bcm27xx/patches-5.10/950-0013-spi-spidev-Completely-disable-the-spidev-warning.patch new file mode 100644 index 0000000000..1d2398cc53 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0013-spi-spidev-Completely-disable-the-spidev-warning.patch @@ -0,0 +1,24 @@ +From 8469be136aebf9fe06746ec47e4495c77d5522f5 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 14 Jul 2015 10:26:09 +0100 +Subject: [PATCH] spi: spidev: Completely disable the spidev warning + +An alternative strategy would be to use "rpi,spidev" instead, but that +would require many Raspberry Pi Device Tree changes. + +Signed-off-by: Phil Elwell +--- + drivers/spi/spidev.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/spi/spidev.c ++++ b/drivers/spi/spidev.c +@@ -733,7 +733,7 @@ static int spidev_probe(struct spi_devic + * compatible string, it is a Linux implementation thing + * rather than a description of the hardware. + */ +- WARN(spi->dev.of_node && ++ WARN(0 && spi->dev.of_node && + of_device_is_compatible(spi->dev.of_node, "spidev"), + "%pOF: buggy DT: spidev listed directly in DT\n", spi->dev.of_node); + diff --git a/target/linux/bcm27xx/patches-5.10/950-0014-dmaengine-bcm2835-Load-driver-early-and-support-lega.patch b/target/linux/bcm27xx/patches-5.10/950-0014-dmaengine-bcm2835-Load-driver-early-and-support-lega.patch new file mode 100644 index 0000000000..f4cf804581 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0014-dmaengine-bcm2835-Load-driver-early-and-support-lega.patch @@ -0,0 +1,101 @@ +From 1fafff0383c50bbbb2d5bb3205923904f3f55ce8 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= +Date: Sat, 3 Oct 2015 22:22:55 +0200 +Subject: [PATCH] dmaengine: bcm2835: Load driver early and support + legacy API +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Load driver early since at least bcm2708_fb doesn't support deferred +probing and even if it did, we don't want the video driver deferred. +Support the legacy DMA API which is needed by bcm2708_fb. +Don't mask out channel 2. + +Signed-off-by: Noralf Trønnes +--- + drivers/dma/Kconfig | 2 +- + drivers/dma/bcm2835-dma.c | 26 +++++++++++++++++++++++++- + 2 files changed, 26 insertions(+), 2 deletions(-) + +--- a/drivers/dma/Kconfig ++++ b/drivers/dma/Kconfig +@@ -134,7 +134,7 @@ config COH901318 + + config DMA_BCM2835 + tristate "BCM2835 DMA engine support" +- depends on ARCH_BCM2835 ++ depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709 + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + +--- a/drivers/dma/bcm2835-dma.c ++++ b/drivers/dma/bcm2835-dma.c +@@ -25,6 +25,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -36,6 +37,7 @@ + + #define BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED 14 + #define BCM2835_DMA_CHAN_NAME_SIZE 8 ++#define BCM2835_DMA_BULK_MASK BIT(0) + + /** + * struct bcm2835_dmadev - BCM2835 DMA controller +@@ -906,6 +908,9 @@ static int bcm2835_dma_probe(struct plat + base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(base)) + return PTR_ERR(base); ++ rc = bcm_dmaman_probe(pdev, base, BCM2835_DMA_BULK_MASK); ++ if (rc) ++ dev_err(&pdev->dev, "Failed to initialize the legacy API\n"); + + od->base = base; + +@@ -951,6 +956,9 @@ static int bcm2835_dma_probe(struct plat + goto err_no_dma; + } + ++ /* Channel 0 is used by the legacy API */ ++ chans_available &= ~BCM2835_DMA_BULK_MASK; ++ + /* get irqs for each channel that we support */ + for (i = 0; i <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; i++) { + /* skip masked out channels */ +@@ -1025,6 +1033,7 @@ static int bcm2835_dma_remove(struct pla + { + struct bcm2835_dmadev *od = platform_get_drvdata(pdev); + ++ bcm_dmaman_remove(pdev); + dma_async_device_unregister(&od->ddev); + bcm2835_dma_free(od); + +@@ -1040,7 +1049,22 @@ static struct platform_driver bcm2835_dm + }, + }; + +-module_platform_driver(bcm2835_dma_driver); ++static int bcm2835_dma_init(void) ++{ ++ return platform_driver_register(&bcm2835_dma_driver); ++} ++ ++static void bcm2835_dma_exit(void) ++{ ++ platform_driver_unregister(&bcm2835_dma_driver); ++} ++ ++/* ++ * Load after serial driver (arch_initcall) so we see the messages if it fails, ++ * but before drivers (module_init) that need a DMA channel. ++ */ ++subsys_initcall(bcm2835_dma_init); ++module_exit(bcm2835_dma_exit); + + MODULE_ALIAS("platform:bcm2835-dma"); + MODULE_DESCRIPTION("BCM2835 DMA engine driver"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0015-firmware-Updated-mailbox-header.patch b/target/linux/bcm27xx/patches-5.10/950-0015-firmware-Updated-mailbox-header.patch new file mode 100644 index 0000000000..ec1e48a047 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0015-firmware-Updated-mailbox-header.patch @@ -0,0 +1,27 @@ +From b7ad81911a06fd8047ca36c07bd49d8317833502 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Mon, 25 Jan 2016 17:25:12 +0000 +Subject: [PATCH] firmware: Updated mailbox header + +--- + include/soc/bcm2835/raspberrypi-firmware.h | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/include/soc/bcm2835/raspberrypi-firmware.h ++++ b/include/soc/bcm2835/raspberrypi-firmware.h +@@ -9,6 +9,8 @@ + #include + #include + ++#define RPI_FIRMWARE_CHAN_FB 1 ++ + struct rpi_firmware; + + enum rpi_firmware_property_status { +@@ -159,5 +161,6 @@ static inline struct rpi_firmware *rpi_f + return NULL; + } + #endif ++int rpi_firmware_transaction(struct rpi_firmware *fw, u32 chan, u32 data); + + #endif /* __SOC_RASPBERRY_FIRMWARE_H__ */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0016-rtc-Add-SPI-alias-for-pcf2123-driver.patch b/target/linux/bcm27xx/patches-5.10/950-0016-rtc-Add-SPI-alias-for-pcf2123-driver.patch new file mode 100644 index 0000000000..383b28bdcc --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0016-rtc-Add-SPI-alias-for-pcf2123-driver.patch @@ -0,0 +1,20 @@ +From d9fa2c594a6dfd5f538c50eaa6a06449d06c5a8e Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 15 Jun 2016 16:48:41 +0100 +Subject: [PATCH] rtc: Add SPI alias for pcf2123 driver + +Without this alias, Device Tree won't cause the driver +to be loaded. + +See: https://github.com/raspberrypi/linux/pull/1510 +--- + drivers/rtc/rtc-pcf2123.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/rtc/rtc-pcf2123.c ++++ b/drivers/rtc/rtc-pcf2123.c +@@ -465,3 +465,4 @@ module_spi_driver(pcf2123_driver); + MODULE_AUTHOR("Chris Verges "); + MODULE_DESCRIPTION("NXP PCF2123 RTC driver"); + MODULE_LICENSE("GPL"); ++MODULE_ALIAS("spi:rtc-pcf2123"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0017-watchdog-bcm2835-Support-setting-reboot-partition.patch b/target/linux/bcm27xx/patches-5.10/950-0017-watchdog-bcm2835-Support-setting-reboot-partition.patch new file mode 100644 index 0000000000..e33b5d4bcf --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0017-watchdog-bcm2835-Support-setting-reboot-partition.patch @@ -0,0 +1,102 @@ +From 351b9cbfc6aed837c7e23462d7109372de22e2bb Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= +Date: Fri, 7 Oct 2016 16:50:59 +0200 +Subject: [PATCH] watchdog: bcm2835: Support setting reboot partition +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +The Raspberry Pi firmware looks at the RSTS register to know which +partition to boot from. The reboot syscall command +LINUX_REBOOT_CMD_RESTART2 supports passing in a string argument. + +Add support for passing in a partition number 0..63 to boot from. +Partition 63 is a special partiton indicating halt. +If the partition doesn't exist, the firmware falls back to partition 0. + +Signed-off-by: Noralf Trønnes +--- + drivers/watchdog/bcm2835_wdt.c | 49 +++++++++++++++++++--------------- + 1 file changed, 27 insertions(+), 22 deletions(-) + +--- a/drivers/watchdog/bcm2835_wdt.c ++++ b/drivers/watchdog/bcm2835_wdt.c +@@ -32,13 +32,7 @@ + #define PM_RSTC_WRCFG_SET 0x00000030 + #define PM_RSTC_WRCFG_FULL_RESET 0x00000020 + #define PM_RSTC_RESET 0x00000102 +- +-/* +- * The Raspberry Pi firmware uses the RSTS register to know which partition +- * to boot from. The partition value is spread into bits 0, 2, 4, 6, 8, 10. +- * Partition 63 is a special partition used by the firmware to indicate halt. +- */ +-#define PM_RSTS_RASPBERRYPI_HALT 0x555 ++#define PM_RSTS_PARTITION_CLR 0xfffffaaa + + #define SECS_TO_WDOG_TICKS(x) ((x) << 16) + #define WDOG_TICKS_TO_SECS(x) ((x) >> 16) +@@ -97,9 +91,24 @@ static unsigned int bcm2835_wdt_get_time + return WDOG_TICKS_TO_SECS(ret & PM_WDOG_TIME_SET); + } + +-static void __bcm2835_restart(struct bcm2835_wdt *wdt) ++/* ++ * The Raspberry Pi firmware uses the RSTS register to know which partiton ++ * to boot from. The partiton value is spread into bits 0, 2, 4, 6, 8, 10. ++ * Partiton 63 is a special partition used by the firmware to indicate halt. ++ */ ++ ++static void __bcm2835_restart(struct bcm2835_wdt *wdt, u8 partition) + { +- u32 val; ++ u32 val, rsts; ++ ++ rsts = (partition & BIT(0)) | ((partition & BIT(1)) << 1) | ++ ((partition & BIT(2)) << 2) | ((partition & BIT(3)) << 3) | ++ ((partition & BIT(4)) << 4) | ((partition & BIT(5)) << 5); ++ ++ val = readl_relaxed(wdt->base + PM_RSTS); ++ val &= PM_RSTS_PARTITION_CLR; ++ val |= PM_PASSWORD | rsts; ++ writel_relaxed(val, wdt->base + PM_RSTS); + + /* use a timeout of 10 ticks (~150us) */ + writel_relaxed(10 | PM_PASSWORD, wdt->base + PM_WDOG); +@@ -117,7 +126,13 @@ static int bcm2835_restart(struct watchd + { + struct bcm2835_wdt *wdt = watchdog_get_drvdata(wdog); + +- __bcm2835_restart(wdt); ++ unsigned long long val; ++ u8 partition = 0; ++ ++ if (data && !kstrtoull(data, 0, &val) && val <= 63) ++ partition = val; ++ ++ __bcm2835_restart(wdt, partition); + + return 0; + } +@@ -152,19 +167,9 @@ static struct watchdog_device bcm2835_wd + static void bcm2835_power_off(void) + { + struct bcm2835_wdt *wdt = bcm2835_power_off_wdt; +- u32 val; +- +- /* +- * We set the watchdog hard reset bit here to distinguish this reset +- * from the normal (full) reset. bootcode.bin will not reboot after a +- * hard reset. +- */ +- val = readl_relaxed(wdt->base + PM_RSTS); +- val |= PM_PASSWORD | PM_RSTS_RASPBERRYPI_HALT; +- writel_relaxed(val, wdt->base + PM_RSTS); + +- /* Continue with normal reset mechanism */ +- __bcm2835_restart(wdt); ++ /* Partition 63 tells the firmware that this is a halt */ ++ __bcm2835_restart(wdt, 63); + } + + static int bcm2835_wdt_probe(struct platform_device *pdev) diff --git a/target/linux/bcm27xx/patches-5.10/950-0018-reboot-Use-power-off-rather-than-busy-spinning-when-.patch b/target/linux/bcm27xx/patches-5.10/950-0018-reboot-Use-power-off-rather-than-busy-spinning-when-.patch new file mode 100644 index 0000000000..36d8bbce24 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0018-reboot-Use-power-off-rather-than-busy-spinning-when-.patch @@ -0,0 +1,23 @@ +From e722eb6ced1ad7a162782fe10dd5d4225a6b4e0d Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Tue, 5 Apr 2016 19:40:12 +0100 +Subject: [PATCH] reboot: Use power off rather than busy spinning when + halt is requested + +--- + arch/arm/kernel/reboot.c | 4 +--- + 1 file changed, 1 insertion(+), 3 deletions(-) + +--- a/arch/arm/kernel/reboot.c ++++ b/arch/arm/kernel/reboot.c +@@ -102,9 +102,7 @@ void machine_shutdown(void) + */ + void machine_halt(void) + { +- local_irq_disable(); +- smp_send_stop(); +- while (1); ++ machine_power_off(); + } + + /* diff --git a/target/linux/bcm27xx/patches-5.10/950-0019-bcm-Make-RASPBERRYPI_POWER-depend-on-PM.patch b/target/linux/bcm27xx/patches-5.10/950-0019-bcm-Make-RASPBERRYPI_POWER-depend-on-PM.patch new file mode 100644 index 0000000000..663fde1233 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0019-bcm-Make-RASPBERRYPI_POWER-depend-on-PM.patch @@ -0,0 +1,19 @@ +From 0bc33dc51825662d4fc7a46c5e622de00e5cbf80 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Wed, 9 Nov 2016 13:02:52 +0000 +Subject: [PATCH] bcm: Make RASPBERRYPI_POWER depend on PM + +--- + drivers/soc/bcm/Kconfig | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/soc/bcm/Kconfig ++++ b/drivers/soc/bcm/Kconfig +@@ -17,6 +17,7 @@ config RASPBERRYPI_POWER + bool "Raspberry Pi power domain driver" + depends on ARCH_BCM2835 || (COMPILE_TEST && OF) + depends on RASPBERRYPI_FIRMWARE=y ++ depends on PM + select PM_GENERIC_DOMAINS if PM + help + This enables support for the RPi power domains which can be enabled diff --git a/target/linux/bcm27xx/patches-5.10/950-0020-Register-the-clocks-early-during-the-boot-process-so.patch b/target/linux/bcm27xx/patches-5.10/950-0020-Register-the-clocks-early-during-the-boot-process-so.patch new file mode 100644 index 0000000000..4c83d165c6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0020-Register-the-clocks-early-during-the-boot-process-so.patch @@ -0,0 +1,45 @@ +From 41e34cd05d40eca6674e25eb9a85e5f7992d4e83 Mon Sep 17 00:00:00 2001 +From: Martin Sperl +Date: Fri, 2 Sep 2016 16:45:27 +0100 +Subject: [PATCH] Register the clocks early during the boot process, so + that special/critical clocks can get enabled early on in the boot process + avoiding the risk of disabling a clock, pll_divider or pll when a claiming + driver fails to install propperly - maybe it needs to defer. + +Signed-off-by: Martin Sperl +--- + drivers/clk/bcm/clk-bcm2835.c | 15 +++++++++++++-- + 1 file changed, 13 insertions(+), 2 deletions(-) + +--- a/drivers/clk/bcm/clk-bcm2835.c ++++ b/drivers/clk/bcm/clk-bcm2835.c +@@ -2295,8 +2295,15 @@ static int bcm2835_clk_probe(struct plat + if (ret) + return ret; + +- return of_clk_add_hw_provider(dev->of_node, of_clk_hw_onecell_get, ++ ret = of_clk_add_hw_provider(dev->of_node, of_clk_hw_onecell_get, + &cprman->onecell); ++ if (ret) ++ return ret; ++ ++ /* note that we have registered all the clocks */ ++ dev_dbg(dev, "registered %d clocks\n", asize); ++ ++ return 0; + } + + static const struct cprman_plat_data cprman_bcm2835_plat_data = { +@@ -2322,7 +2329,11 @@ static struct platform_driver bcm2835_cl + .probe = bcm2835_clk_probe, + }; + +-builtin_platform_driver(bcm2835_clk_driver); ++static int __init __bcm2835_clk_driver_init(void) ++{ ++ return platform_driver_register(&bcm2835_clk_driver); ++} ++core_initcall(__bcm2835_clk_driver_init); + + MODULE_AUTHOR("Eric Anholt "); + MODULE_DESCRIPTION("BCM2835 clock driver"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0021-bcm2835-rng-Avoid-initialising-if-already-enabled.patch b/target/linux/bcm27xx/patches-5.10/950-0021-bcm2835-rng-Avoid-initialising-if-already-enabled.patch new file mode 100644 index 0000000000..bace3071d5 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0021-bcm2835-rng-Avoid-initialising-if-already-enabled.patch @@ -0,0 +1,25 @@ +From 102d9fbd0a8d762835a9f9a7917e9eace3a9d84e Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Tue, 6 Dec 2016 17:05:39 +0000 +Subject: [PATCH] bcm2835-rng: Avoid initialising if already enabled + +Avoids the 0x40000 cycles of warmup again if firmware has already used it +--- + drivers/char/hw_random/bcm2835-rng.c | 6 ++++-- + 1 file changed, 4 insertions(+), 2 deletions(-) + +--- a/drivers/char/hw_random/bcm2835-rng.c ++++ b/drivers/char/hw_random/bcm2835-rng.c +@@ -102,8 +102,10 @@ static int bcm2835_rng_init(struct hwrng + } + + /* set warm-up count & enable */ +- rng_writel(priv, RNG_WARMUP_COUNT, RNG_STATUS); +- rng_writel(priv, RNG_RBGEN, RNG_CTRL); ++ if (!(rng_readl(priv, RNG_CTRL) & RNG_RBGEN)) { ++ rng_writel(priv, RNG_WARMUP_COUNT, RNG_STATUS); ++ rng_writel(priv, RNG_RBGEN, RNG_CTRL); ++ } + + return ret; + } diff --git a/target/linux/bcm27xx/patches-5.10/950-0022-clk-bcm2835-Mark-used-PLLs-and-dividers-CRITICAL.patch b/target/linux/bcm27xx/patches-5.10/950-0022-clk-bcm2835-Mark-used-PLLs-and-dividers-CRITICAL.patch new file mode 100644 index 0000000000..4a0f1c5ad6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0022-clk-bcm2835-Mark-used-PLLs-and-dividers-CRITICAL.patch @@ -0,0 +1,28 @@ +From 3af9c4ed5775b7675e679a80a381eafe2ce726ae Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 13 Feb 2017 17:20:08 +0000 +Subject: [PATCH] clk-bcm2835: Mark used PLLs and dividers CRITICAL + +The VPU configures and relies on several PLLs and dividers. Mark all +enabled dividers and their PLLs as CRITICAL to prevent the kernel from +switching them off. + +Signed-off-by: Phil Elwell +--- + drivers/clk/bcm/clk-bcm2835.c | 5 +++++ + 1 file changed, 5 insertions(+) + +--- a/drivers/clk/bcm/clk-bcm2835.c ++++ b/drivers/clk/bcm/clk-bcm2835.c +@@ -1384,6 +1384,11 @@ bcm2835_register_pll_divider(struct bcm2 + divider->div.hw.init = &init; + divider->div.table = NULL; + ++ if (!(cprman_read(cprman, data->cm_reg) & data->hold_mask)) { ++ init.flags |= CLK_IS_CRITICAL; ++ divider->div.flags |= CLK_IS_CRITICAL; ++ } ++ + divider->cprman = cprman; + divider->data = divider_data; + diff --git a/target/linux/bcm27xx/patches-5.10/950-0023-clk-bcm2835-Add-claim-clocks-property.patch b/target/linux/bcm27xx/patches-5.10/950-0023-clk-bcm2835-Add-claim-clocks-property.patch new file mode 100644 index 0000000000..efd1ccd268 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0023-clk-bcm2835-Add-claim-clocks-property.patch @@ -0,0 +1,120 @@ +From 05cae664e29e510111cf24f2beb1c31cba09bcce Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 13 Feb 2017 17:20:08 +0000 +Subject: [PATCH] clk-bcm2835: Add claim-clocks property + +The claim-clocks property can be used to prevent PLLs and dividers +from being marked as critical. It contains a vector of clock IDs, +as defined by dt-bindings/clock/bcm2835.h. + +Use this mechanism to claim PLLD_DSI0, PLLD_DSI1, PLLH_AUX and +PLLH_PIX for the vc4_kms_v3d driver. + +Signed-off-by: Phil Elwell +--- + drivers/clk/bcm/clk-bcm2835.c | 45 ++++++++++++++++++++++++++++++++--- + 1 file changed, 42 insertions(+), 3 deletions(-) + +--- a/drivers/clk/bcm/clk-bcm2835.c ++++ b/drivers/clk/bcm/clk-bcm2835.c +@@ -1312,6 +1312,8 @@ static const struct clk_ops bcm2835_vpu_ + .debug_init = bcm2835_clock_debug_init, + }; + ++static bool bcm2835_clk_is_claimed(const char *name); ++ + static struct clk_hw *bcm2835_register_pll(struct bcm2835_cprman *cprman, + const void *data) + { +@@ -1329,6 +1331,9 @@ static struct clk_hw *bcm2835_register_p + init.ops = &bcm2835_pll_clk_ops; + init.flags = pll_data->flags | CLK_IGNORE_UNUSED; + ++ if (!bcm2835_clk_is_claimed(pll_data->name)) ++ init.flags |= CLK_IS_CRITICAL; ++ + pll = kzalloc(sizeof(*pll), GFP_KERNEL); + if (!pll) + return NULL; +@@ -1384,9 +1389,11 @@ bcm2835_register_pll_divider(struct bcm2 + divider->div.hw.init = &init; + divider->div.table = NULL; + +- if (!(cprman_read(cprman, data->cm_reg) & data->hold_mask)) { +- init.flags |= CLK_IS_CRITICAL; +- divider->div.flags |= CLK_IS_CRITICAL; ++ if (!(cprman_read(cprman, divider_data->cm_reg) & divider_data->hold_mask)) { ++ if (!bcm2835_clk_is_claimed(divider_data->source_pll)) ++ init.flags |= CLK_IS_CRITICAL; ++ if (!bcm2835_clk_is_claimed(divider_data->name)) ++ divider->div.flags |= CLK_IS_CRITICAL; + } + + divider->cprman = cprman; +@@ -1443,6 +1450,15 @@ static struct clk_hw *bcm2835_register_c + init.flags = clock_data->flags | CLK_IGNORE_UNUSED; + + /* ++ * Some GPIO clocks for ethernet/wifi PLLs are marked as ++ * critical (since some platforms use them), but if the ++ * firmware didn't have them turned on then they clearly ++ * aren't actually critical. ++ */ ++ if ((cprman_read(cprman, clock_data->ctl_reg) & CM_ENABLE) == 0) ++ init.flags &= ~CLK_IS_CRITICAL; ++ ++ /* + * Pass the CLK_SET_RATE_PARENT flag if we are allowed to propagate + * rate changes on at least of the parents. + */ +@@ -2221,6 +2237,8 @@ static const struct bcm2835_clk_desc clk + .ctl_reg = CM_PERIICTL), + }; + ++static bool bcm2835_clk_claimed[ARRAY_SIZE(clk_desc_array)]; ++ + /* + * Permanently take a reference on the parent of the SDRAM clock. + * +@@ -2240,6 +2258,19 @@ static int bcm2835_mark_sdc_parent_criti + return clk_prepare_enable(parent); + } + ++static bool bcm2835_clk_is_claimed(const char *name) ++{ ++ int i; ++ ++ for (i = 0; i < ARRAY_SIZE(clk_desc_array); i++) { ++ const char *clk_name = *(const char **)(clk_desc_array[i].data); ++ if (!strcmp(name, clk_name)) ++ return bcm2835_clk_claimed[i]; ++ } ++ ++ return false; ++} ++ + static int bcm2835_clk_probe(struct platform_device *pdev) + { + struct device *dev = &pdev->dev; +@@ -2249,6 +2280,7 @@ static int bcm2835_clk_probe(struct plat + const size_t asize = ARRAY_SIZE(clk_desc_array); + const struct cprman_plat_data *pdata; + size_t i; ++ u32 clk_id; + int ret; + + pdata = of_device_get_match_data(&pdev->dev); +@@ -2267,6 +2299,13 @@ static int bcm2835_clk_probe(struct plat + if (IS_ERR(cprman->regs)) + return PTR_ERR(cprman->regs); + ++ memset(bcm2835_clk_claimed, 0, sizeof(bcm2835_clk_claimed)); ++ for (i = 0; ++ !of_property_read_u32_index(pdev->dev.of_node, "claim-clocks", ++ i, &clk_id); ++ i++) ++ bcm2835_clk_claimed[clk_id]= true; ++ + memcpy(cprman->real_parent_names, cprman_parent_names, + sizeof(cprman_parent_names)); + of_clk_parent_fill(dev->of_node, cprman->real_parent_names, diff --git a/target/linux/bcm27xx/patches-5.10/950-0024-clk-bcm2835-Read-max-core-clock-from-firmware.patch b/target/linux/bcm27xx/patches-5.10/950-0024-clk-bcm2835-Read-max-core-clock-from-firmware.patch new file mode 100644 index 0000000000..8ad9a6edc7 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0024-clk-bcm2835-Read-max-core-clock-from-firmware.patch @@ -0,0 +1,115 @@ +From 6ac8a6c58b51d02780b7a1fc882df33ae2560798 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 6 Mar 2017 09:06:18 +0000 +Subject: [PATCH] clk-bcm2835: Read max core clock from firmware + +The VPU is responsible for managing the core clock, usually under +direction from the bcm2835-cpufreq driver but not via the clk-bcm2835 +driver. Since the core frequency can change without warning, it is +safer to report the maximum clock rate to users of the core clock - +I2C, SPI and the mini UART - to err on the safe side when calculating +clock divisors. + +If the DT node for the clock driver includes a reference to the +firmware node, use the firmware API to query the maximum core clock +instead of reading the divider registers. + +Prior to this patch, a "100KHz" I2C bus was sometimes clocked at about +160KHz. In particular, switching to the 4.9 kernel was likely to break +SenseHAT usage on a Pi3. + +Signed-off-by: Phil Elwell +--- + drivers/clk/bcm/clk-bcm2835.c | 39 ++++++++++++++++++++++++++++++++++- + 1 file changed, 38 insertions(+), 1 deletion(-) + +--- a/drivers/clk/bcm/clk-bcm2835.c ++++ b/drivers/clk/bcm/clk-bcm2835.c +@@ -35,6 +35,7 @@ + #include + #include + #include ++#include + + #define CM_PASSWORD 0x5a000000 + +@@ -295,6 +296,8 @@ + #define SOC_BCM2711 BIT(1) + #define SOC_ALL (SOC_BCM2835 | SOC_BCM2711) + ++#define VCMSG_ID_CORE_CLOCK 4 ++ + /* + * Names of clocks used within the driver that need to be replaced + * with an external parent's name. This array is in the order that +@@ -313,6 +316,7 @@ static const char *const cprman_parent_n + struct bcm2835_cprman { + struct device *dev; + void __iomem *regs; ++ struct rpi_firmware *fw; + spinlock_t regs_lock; /* spinlock for all clocks */ + unsigned int soc; + +@@ -1016,6 +1020,30 @@ static unsigned long bcm2835_clock_get_r + return bcm2835_clock_rate_from_divisor(clock, parent_rate, div); + } + ++static unsigned long bcm2835_clock_get_rate_vpu(struct clk_hw *hw, ++ unsigned long parent_rate) ++{ ++ struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw); ++ struct bcm2835_cprman *cprman = clock->cprman; ++ ++ if (cprman->fw) { ++ struct { ++ u32 id; ++ u32 val; ++ } packet; ++ ++ packet.id = VCMSG_ID_CORE_CLOCK; ++ packet.val = 0; ++ ++ if (!rpi_firmware_property(cprman->fw, ++ RPI_FIRMWARE_GET_MAX_CLOCK_RATE, ++ &packet, sizeof(packet))) ++ return packet.val; ++ } ++ ++ return bcm2835_clock_get_rate(hw, parent_rate); ++} ++ + static void bcm2835_clock_wait_busy(struct bcm2835_clock *clock) + { + struct bcm2835_cprman *cprman = clock->cprman; +@@ -1304,7 +1332,7 @@ static int bcm2835_vpu_clock_is_on(struc + */ + static const struct clk_ops bcm2835_vpu_clock_clk_ops = { + .is_prepared = bcm2835_vpu_clock_is_on, +- .recalc_rate = bcm2835_clock_get_rate, ++ .recalc_rate = bcm2835_clock_get_rate_vpu, + .set_rate = bcm2835_clock_set_rate, + .determine_rate = bcm2835_clock_determine_rate, + .set_parent = bcm2835_clock_set_parent, +@@ -2279,6 +2307,7 @@ static int bcm2835_clk_probe(struct plat + const struct bcm2835_clk_desc *desc; + const size_t asize = ARRAY_SIZE(clk_desc_array); + const struct cprman_plat_data *pdata; ++ struct device_node *fw_node; + size_t i; + u32 clk_id; + int ret; +@@ -2299,6 +2328,14 @@ static int bcm2835_clk_probe(struct plat + if (IS_ERR(cprman->regs)) + return PTR_ERR(cprman->regs); + ++ fw_node = of_parse_phandle(dev->of_node, "firmware", 0); ++ if (fw_node) { ++ struct rpi_firmware *fw = rpi_firmware_get(NULL); ++ if (!fw) ++ return -EPROBE_DEFER; ++ cprman->fw = fw; ++ } ++ + memset(bcm2835_clk_claimed, 0, sizeof(bcm2835_clk_claimed)); + for (i = 0; + !of_property_read_u32_index(pdev->dev.of_node, "claim-clocks", diff --git a/target/linux/bcm27xx/patches-5.10/950-0025-sound-Demote-deferral-errors-to-INFO-level.patch b/target/linux/bcm27xx/patches-5.10/950-0025-sound-Demote-deferral-errors-to-INFO-level.patch new file mode 100644 index 0000000000..d97a97eedf --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0025-sound-Demote-deferral-errors-to-INFO-level.patch @@ -0,0 +1,35 @@ +From 2a0e0c15c001bfde3666f159552e414217fe44ac Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 9 Feb 2017 14:36:44 +0000 +Subject: [PATCH] sound: Demote deferral errors to INFO level + +At present there is no mechanism to specify driver load order, +which can lead to deferrals and repeated retries until successful. +Since this situation is expected, reduce the dmesg level to +INFO and mention that the operation will be retried. + +Signed-off-by: Phil Elwell +--- + sound/soc/soc-core.c | 4 ++-- + 1 file changed, 2 insertions(+), 2 deletions(-) + +--- a/sound/soc/soc-core.c ++++ b/sound/soc/soc-core.c +@@ -1016,7 +1016,7 @@ int snd_soc_add_pcm_runtime(struct snd_s + for_each_link_cpus(dai_link, i, cpu) { + asoc_rtd_to_cpu(rtd, i) = snd_soc_find_dai(cpu); + if (!asoc_rtd_to_cpu(rtd, i)) { +- dev_info(card->dev, "ASoC: CPU DAI %s not registered\n", ++ dev_info(card->dev, "ASoC: CPU DAI %s not registered - will retry\n", + cpu->dai_name); + goto _err_defer; + } +@@ -1027,7 +1027,7 @@ int snd_soc_add_pcm_runtime(struct snd_s + for_each_link_codecs(dai_link, i, codec) { + asoc_rtd_to_codec(rtd, i) = snd_soc_find_dai(codec); + if (!asoc_rtd_to_codec(rtd, i)) { +- dev_info(card->dev, "ASoC: CODEC DAI %s not registered\n", ++ dev_info(card->dev, "ASoC: CODEC DAI %s not registered- will retry\n", + codec->dai_name); + goto _err_defer; + } diff --git a/target/linux/bcm27xx/patches-5.10/950-0026-Update-vfpmodule.c.patch b/target/linux/bcm27xx/patches-5.10/950-0026-Update-vfpmodule.c.patch new file mode 100644 index 0000000000..51bf29b14c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0026-Update-vfpmodule.c.patch @@ -0,0 +1,137 @@ +From 55f18cc01fc9c93999ea935f7d869d136f5204ed Mon Sep 17 00:00:00 2001 +From: Claggy3 +Date: Sat, 11 Feb 2017 14:00:30 +0000 +Subject: [PATCH] Update vfpmodule.c + +Christopher Alexander Tobias Schulze - May 2, 2015, 11:57 a.m. +This patch fixes a problem with VFP state save and restore related +to exception handling (panic with message "BUG: unsupported FP +instruction in kernel mode") present on VFP11 floating point units +(as used with ARM1176JZF-S CPUs, e.g. on first generation Raspberry +Pi boards). This patch was developed and discussed on + + https://github.com/raspberrypi/linux/issues/859 + +A precondition to see the crashes is that floating point exception +traps are enabled. In this case, the VFP11 might determine that a FPU +operation needs to trap at a point in time when it is not possible to +signal this to the ARM11 core any more. The VFP11 will then set the +FPEXC.EX bit and store the trapped opcode in FPINST. (In some cases, +a second opcode might have been accepted by the VFP11 before the +exception was detected and could be reported to the ARM11 - in this +case, the VFP11 also sets FPEXC.FP2V and stores the second opcode in +FPINST2.) + +If FPEXC.EX is set, the VFP11 will "bounce" the next FPU opcode issued +by the ARM11 CPU, which will be seen by the ARM11 as an undefined opcode +trap. The VFP support code examines the FPEXC.EX and FPEXC.FP2V bits +to decide what actions to take, i.e., whether to emulate the opcodes +found in FPINST and FPINST2, and whether to retry the bounced instruction. + +If a user space application has left the VFP11 in this "pending trap" +state, the next FPU opcode issued to the VFP11 might actually be the +VSTMIA operation vfp_save_state() uses to store the FPU registers +to memory (in our test cases, when building the signal stack frame). +In this case, the kernel crashes as described above. + +This patch fixes the problem by making sure that vfp_save_state() is +always entered with FPEXC.EX cleared. (The current value of FPEXC has +already been saved, so this does not corrupt the context. Clearing +FPEXC.EX has no effects on FPINST or FPINST2. Also note that many +callers already modify FPEXC by setting FPEXC.EN before invoking +vfp_save_state().) + +This patch also addresses a second problem related to FPEXC.EX: After +returning from signal handling, the kernel reloads the VFP context +from the user mode stack. However, the current code explicitly clears +both FPEXC.EX and FPEXC.FP2V during reload. As VFP11 requires these +bits to be preserved, this patch disables clearing them for VFP +implementations belonging to architecture 1. There should be no +negative side effects: the user can set both bits by executing FPU +opcodes anyway, and while user code may now place arbitrary values +into FPINST and FPINST2 (e.g., non-VFP ARM opcodes) the VFP support +code knows which instructions can be emulated, and rejects other +opcodes with "unhandled bounce" messages, so there should be no +security impact from allowing reloading FPEXC.EX and FPEXC.FP2V. + +Signed-off-by: Christopher Alexander Tobias Schulze +--- + arch/arm/vfp/vfpmodule.c | 25 +++++++++++++++++++------ + 1 file changed, 19 insertions(+), 6 deletions(-) + +--- a/arch/arm/vfp/vfpmodule.c ++++ b/arch/arm/vfp/vfpmodule.c +@@ -176,8 +176,11 @@ static int vfp_notifier(struct notifier_ + * case the thread migrates to a different CPU. The + * restoring is done lazily. + */ +- if ((fpexc & FPEXC_EN) && vfp_current_hw_state[cpu]) ++ if ((fpexc & FPEXC_EN) && vfp_current_hw_state[cpu]) { ++ /* vfp_save_state oopses on VFP11 if EX bit set */ ++ fmxr(FPEXC, fpexc & ~FPEXC_EX); + vfp_save_state(vfp_current_hw_state[cpu], fpexc); ++ } + #endif + + /* +@@ -454,13 +457,16 @@ static int vfp_pm_suspend(void) + /* if vfp is on, then save state for resumption */ + if (fpexc & FPEXC_EN) { + pr_debug("%s: saving vfp state\n", __func__); ++ /* vfp_save_state oopses on VFP11 if EX bit set */ ++ fmxr(FPEXC, fpexc & ~FPEXC_EX); + vfp_save_state(&ti->vfpstate, fpexc); + + /* disable, just in case */ + fmxr(FPEXC, fmrx(FPEXC) & ~FPEXC_EN); + } else if (vfp_current_hw_state[ti->cpu]) { + #ifndef CONFIG_SMP +- fmxr(FPEXC, fpexc | FPEXC_EN); ++ /* vfp_save_state oopses on VFP11 if EX bit set */ ++ fmxr(FPEXC, (fpexc & ~FPEXC_EX) | FPEXC_EN); + vfp_save_state(vfp_current_hw_state[ti->cpu], fpexc); + fmxr(FPEXC, fpexc); + #endif +@@ -523,7 +529,8 @@ void vfp_sync_hwstate(struct thread_info + /* + * Save the last VFP state on this CPU. + */ +- fmxr(FPEXC, fpexc | FPEXC_EN); ++ /* vfp_save_state oopses on VFP11 if EX bit set */ ++ fmxr(FPEXC, (fpexc & ~FPEXC_EX) | FPEXC_EN); + vfp_save_state(&thread->vfpstate, fpexc | FPEXC_EN); + fmxr(FPEXC, fpexc); + } +@@ -589,6 +596,7 @@ int vfp_restore_user_hwstate(struct user + struct thread_info *thread = current_thread_info(); + struct vfp_hard_struct *hwstate = &thread->vfpstate.hard; + unsigned long fpexc; ++ u32 fpsid = fmrx(FPSID); + + /* Disable VFP to avoid corrupting the new thread state. */ + vfp_flush_hwstate(thread); +@@ -611,8 +619,12 @@ int vfp_restore_user_hwstate(struct user + /* Ensure the VFP is enabled. */ + fpexc |= FPEXC_EN; + +- /* Ensure FPINST2 is invalid and the exception flag is cleared. */ +- fpexc &= ~(FPEXC_EX | FPEXC_FP2V); ++ /* Mask FPXEC_EX and FPEXC_FP2V if not required by VFP arch */ ++ if ((fpsid & FPSID_ARCH_MASK) != (1 << FPSID_ARCH_BIT)) { ++ /* Ensure FPINST2 is invalid and the exception flag is cleared. */ ++ fpexc &= ~(FPEXC_EX | FPEXC_FP2V); ++ } ++ + hwstate->fpexc = fpexc; + + hwstate->fpinst = ufp_exc->fpinst; +@@ -726,7 +738,8 @@ void kernel_neon_begin(void) + cpu = get_cpu(); + + fpexc = fmrx(FPEXC) | FPEXC_EN; +- fmxr(FPEXC, fpexc); ++ /* vfp_save_state oopses on VFP11 if EX bit set */ ++ fmxr(FPEXC, fpexc & ~FPEXC_EX); + + /* + * Save the userland NEON/VFP state. Under UP, diff --git a/target/linux/bcm27xx/patches-5.10/950-0027-i2c-bcm2835-Add-debug-support.patch b/target/linux/bcm27xx/patches-5.10/950-0027-i2c-bcm2835-Add-debug-support.patch new file mode 100644 index 0000000000..f481af1f9d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0027-i2c-bcm2835-Add-debug-support.patch @@ -0,0 +1,189 @@ +From ee7f5d2470712e25e2bde81ead7c191a3eff41e2 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= +Date: Tue, 1 Nov 2016 15:15:41 +0100 +Subject: [PATCH] i2c: bcm2835: Add debug support +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +This adds a debug module parameter to aid in debugging transfer issues +by printing info to the kernel log. When enabled, status values are +collected in the interrupt routine and msg info in +bcm2835_i2c_start_transfer(). This is done in a way that tries to avoid +affecting timing. Having printk in the isr can mask issues. + +debug values (additive): +1: Print info on error +2: Print info on all transfers +3: Print messages before transfer is started + +The value can be changed at runtime: +/sys/module/i2c_bcm2835/parameters/debug + +Example output, debug=3: +[ 747.114448] bcm2835_i2c_xfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1] +[ 747.114463] bcm2835_i2c_xfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1] +[ 747.117809] start_transfer: msg(1/2) write addr=0x54, len=2 flags= [i2c1] +[ 747.117825] isr: remain=2, status=0x30000055 : TA TXW TXD TXE [i2c1] +[ 747.117839] start_transfer: msg(2/2) read addr=0x54, len=32 flags= [i2c1] +[ 747.117849] isr: remain=32, status=0xd0000039 : TA RXR TXD RXD [i2c1] +[ 747.117861] isr: remain=20, status=0xd0000039 : TA RXR TXD RXD [i2c1] +[ 747.117870] isr: remain=8, status=0x32 : DONE TXD RXD [i2c1] + +Signed-off-by: Noralf Trønnes +--- + drivers/i2c/busses/i2c-bcm2835.c | 99 +++++++++++++++++++++++++++++++- + 1 file changed, 98 insertions(+), 1 deletion(-) + +--- a/drivers/i2c/busses/i2c-bcm2835.c ++++ b/drivers/i2c/busses/i2c-bcm2835.c +@@ -51,6 +51,18 @@ + #define BCM2835_I2C_CDIV_MIN 0x0002 + #define BCM2835_I2C_CDIV_MAX 0xFFFE + ++static unsigned int debug; ++module_param(debug, uint, 0644); ++MODULE_PARM_DESC(debug, "1=err, 2=isr, 3=xfer"); ++ ++#define BCM2835_DEBUG_MAX 512 ++struct bcm2835_debug { ++ struct i2c_msg *msg; ++ int msg_idx; ++ size_t remain; ++ u32 status; ++}; ++ + struct bcm2835_i2c_dev { + struct device *dev; + void __iomem *regs; +@@ -63,8 +75,78 @@ struct bcm2835_i2c_dev { + u32 msg_err; + u8 *msg_buf; + size_t msg_buf_remaining; ++ struct bcm2835_debug debug[BCM2835_DEBUG_MAX]; ++ unsigned int debug_num; ++ unsigned int debug_num_msgs; + }; + ++static inline void bcm2835_debug_add(struct bcm2835_i2c_dev *i2c_dev, u32 s) ++{ ++ if (!i2c_dev->debug_num_msgs || i2c_dev->debug_num >= BCM2835_DEBUG_MAX) ++ return; ++ ++ i2c_dev->debug[i2c_dev->debug_num].msg = i2c_dev->curr_msg; ++ i2c_dev->debug[i2c_dev->debug_num].msg_idx = ++ i2c_dev->debug_num_msgs - i2c_dev->num_msgs; ++ i2c_dev->debug[i2c_dev->debug_num].remain = i2c_dev->msg_buf_remaining; ++ i2c_dev->debug[i2c_dev->debug_num].status = s; ++ i2c_dev->debug_num++; ++} ++ ++static void bcm2835_debug_print_status(struct bcm2835_i2c_dev *i2c_dev, ++ struct bcm2835_debug *d) ++{ ++ u32 s = d->status; ++ ++ pr_info("isr: remain=%zu, status=0x%x : %s%s%s%s%s%s%s%s%s%s [i2c%d]\n", ++ d->remain, s, ++ s & BCM2835_I2C_S_TA ? "TA " : "", ++ s & BCM2835_I2C_S_DONE ? "DONE " : "", ++ s & BCM2835_I2C_S_TXW ? "TXW " : "", ++ s & BCM2835_I2C_S_RXR ? "RXR " : "", ++ s & BCM2835_I2C_S_TXD ? "TXD " : "", ++ s & BCM2835_I2C_S_RXD ? "RXD " : "", ++ s & BCM2835_I2C_S_TXE ? "TXE " : "", ++ s & BCM2835_I2C_S_RXF ? "RXF " : "", ++ s & BCM2835_I2C_S_ERR ? "ERR " : "", ++ s & BCM2835_I2C_S_CLKT ? "CLKT " : "", ++ i2c_dev->adapter.nr); ++} ++ ++static void bcm2835_debug_print_msg(struct bcm2835_i2c_dev *i2c_dev, ++ struct i2c_msg *msg, int i, int total, ++ const char *fname) ++{ ++ pr_info("%s: msg(%d/%d) %s addr=0x%02x, len=%u flags=%s%s%s%s%s%s%s [i2c%d]\n", ++ fname, i, total, ++ msg->flags & I2C_M_RD ? "read" : "write", msg->addr, msg->len, ++ msg->flags & I2C_M_TEN ? "TEN" : "", ++ msg->flags & I2C_M_RECV_LEN ? "RECV_LEN" : "", ++ msg->flags & I2C_M_NO_RD_ACK ? "NO_RD_ACK" : "", ++ msg->flags & I2C_M_IGNORE_NAK ? "IGNORE_NAK" : "", ++ msg->flags & I2C_M_REV_DIR_ADDR ? "REV_DIR_ADDR" : "", ++ msg->flags & I2C_M_NOSTART ? "NOSTART" : "", ++ msg->flags & I2C_M_STOP ? "STOP" : "", ++ i2c_dev->adapter.nr); ++} ++ ++static void bcm2835_debug_print(struct bcm2835_i2c_dev *i2c_dev) ++{ ++ struct bcm2835_debug *d; ++ unsigned int i; ++ ++ for (i = 0; i < i2c_dev->debug_num; i++) { ++ d = &i2c_dev->debug[i]; ++ if (d->status == ~0) ++ bcm2835_debug_print_msg(i2c_dev, d->msg, d->msg_idx, ++ i2c_dev->debug_num_msgs, "start_transfer"); ++ else ++ bcm2835_debug_print_status(i2c_dev, d); ++ } ++ if (i2c_dev->debug_num >= BCM2835_DEBUG_MAX) ++ pr_info("BCM2835_DEBUG_MAX reached\n"); ++} ++ + static inline void bcm2835_i2c_writel(struct bcm2835_i2c_dev *i2c_dev, + u32 reg, u32 val) + { +@@ -252,6 +334,7 @@ static void bcm2835_i2c_start_transfer(s + bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_A, msg->addr); + bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_DLEN, msg->len); + bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, c); ++ bcm2835_debug_add(i2c_dev, ~0); + } + + static void bcm2835_i2c_finish_transfer(struct bcm2835_i2c_dev *i2c_dev) +@@ -278,6 +361,7 @@ static irqreturn_t bcm2835_i2c_isr(int t + u32 val, err; + + val = bcm2835_i2c_readl(i2c_dev, BCM2835_I2C_S); ++ bcm2835_debug_add(i2c_dev, val); + + err = val & (BCM2835_I2C_S_CLKT | BCM2835_I2C_S_ERR); + if (err) { +@@ -344,6 +428,13 @@ static int bcm2835_i2c_xfer(struct i2c_a + unsigned long time_left; + int i; + ++ if (debug) ++ i2c_dev->debug_num_msgs = num; ++ ++ if (debug > 2) ++ for (i = 0; i < num; i++) ++ bcm2835_debug_print_msg(i2c_dev, &msgs[i], i + 1, num, __func__); ++ + for (i = 0; i < (num - 1); i++) + if (msgs[i].flags & I2C_M_RD) { + dev_warn_once(i2c_dev->dev, +@@ -362,6 +453,10 @@ static int bcm2835_i2c_xfer(struct i2c_a + + bcm2835_i2c_finish_transfer(i2c_dev); + ++ if (debug > 1 || (debug && (!time_left || i2c_dev->msg_err))) ++ bcm2835_debug_print(i2c_dev); ++ i2c_dev->debug_num_msgs = 0; ++ i2c_dev->debug_num = 0; + if (!time_left) { + bcm2835_i2c_writel(i2c_dev, BCM2835_I2C_C, + BCM2835_I2C_C_CLEAR); +@@ -372,7 +467,9 @@ static int bcm2835_i2c_xfer(struct i2c_a + if (!i2c_dev->msg_err) + return num; + +- dev_dbg(i2c_dev->dev, "i2c transfer failed: %x\n", i2c_dev->msg_err); ++ if (debug) ++ dev_err(i2c_dev->dev, "i2c transfer failed: %x\n", ++ i2c_dev->msg_err); + + if (i2c_dev->msg_err & BCM2835_I2C_S_ERR) + return -EREMOTEIO; diff --git a/target/linux/bcm27xx/patches-5.10/950-0028-mm-Remove-the-PFN-busy-warning.patch b/target/linux/bcm27xx/patches-5.10/950-0028-mm-Remove-the-PFN-busy-warning.patch new file mode 100644 index 0000000000..6d12c3f308 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0028-mm-Remove-the-PFN-busy-warning.patch @@ -0,0 +1,25 @@ +From a432a3f7142e7e76fd1708debe509ffbea3a3658 Mon Sep 17 00:00:00 2001 +From: Eric Anholt +Date: Thu, 18 Dec 2014 16:07:15 -0800 +Subject: [PATCH] mm: Remove the PFN busy warning + +See commit dae803e165a11bc88ca8dbc07a11077caf97bbcb -- the warning is +expected sometimes when using CMA. However, that commit still spams +my kernel log with these warnings. + +Signed-off-by: Eric Anholt +--- + mm/page_alloc.c | 2 -- + 1 file changed, 2 deletions(-) + +--- a/mm/page_alloc.c ++++ b/mm/page_alloc.c +@@ -8594,8 +8594,6 @@ int alloc_contig_range(unsigned long sta + + /* Make sure the range is really isolated. */ + if (test_pages_isolated(outer_start, end, 0)) { +- pr_info_ratelimited("%s: [%lx, %lx) PFNs busy\n", +- __func__, outer_start, end); + ret = -EBUSY; + goto done; + } diff --git a/target/linux/bcm27xx/patches-5.10/950-0029-irqchip-irq-bcm2836-Remove-regmap-and-syscon-use.patch b/target/linux/bcm27xx/patches-5.10/950-0029-irqchip-irq-bcm2836-Remove-regmap-and-syscon-use.patch new file mode 100644 index 0000000000..73866d6f54 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0029-irqchip-irq-bcm2836-Remove-regmap-and-syscon-use.patch @@ -0,0 +1,112 @@ +From 9ab633ec6dd4bb60c13486c8474cf30045c0a422 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 23 Jan 2018 16:52:45 +0000 +Subject: [PATCH] irqchip: irq-bcm2836: Remove regmap and syscon use + +The syscon node defines a register range that duplicates that used by +the local_intc node on bcm2836/7. Since irq-bcm2835 and irq-bcm2836 are +built in and always present together (both drivers are enabled by +CONFIG_ARCH_BCM2835), it is possible to replace the syscon usage with a +global variable that simplifies the code. Doing so does lose the +locking provided by regmap, but as only one side is using the regmap +interface (irq-bcm2835 uses readl and write) there is no loss of +atomicity. + +See: https://github.com/raspberrypi/firmware/issues/926 + +Signed-off-by: Phil Elwell +--- + drivers/irqchip/irq-bcm2835.c | 32 ++++++++++++-------------------- + drivers/irqchip/irq-bcm2836.c | 5 +++++ + 2 files changed, 17 insertions(+), 20 deletions(-) + +--- a/drivers/irqchip/irq-bcm2835.c ++++ b/drivers/irqchip/irq-bcm2835.c +@@ -41,8 +41,6 @@ + #include + #include + #include +-#include +-#include + + #include + #include +@@ -92,7 +90,7 @@ struct armctrl_ic { + void __iomem *enable[NR_BANKS]; + void __iomem *disable[NR_BANKS]; + struct irq_domain *domain; +- struct regmap *local_regmap; ++ void __iomem *local_base; + }; + + static struct armctrl_ic intc __read_mostly; +@@ -129,24 +127,20 @@ static void armctrl_unmask_irq(struct ir + if (d->hwirq >= NUMBER_IRQS) { + if (num_online_cpus() > 1) { + unsigned int data; +- int ret; + +- if (!intc.local_regmap) { +- pr_err("FIQ is disabled due to missing regmap\n"); ++ if (!intc.local_base) { ++ pr_err("FIQ is disabled due to missing arm_local_intc\n"); + return; + } + +- ret = regmap_read(intc.local_regmap, +- ARM_LOCAL_GPU_INT_ROUTING, &data); +- if (ret) { +- pr_err("Failed to read int routing %d\n", ret); +- return; +- } ++ data = readl_relaxed(intc.local_base + ++ ARM_LOCAL_GPU_INT_ROUTING); + + data &= ~0xc; + data |= (1 << 2); +- regmap_write(intc.local_regmap, +- ARM_LOCAL_GPU_INT_ROUTING, data); ++ writel_relaxed(data, ++ intc.local_base + ++ ARM_LOCAL_GPU_INT_ROUTING); + } + + writel_relaxed(REG_FIQ_ENABLE | hwirq_to_fiq(d->hwirq), +@@ -246,12 +240,10 @@ static int __init armctrl_of_init(struct + } + + if (is_2836) { +- intc.local_regmap = +- syscon_regmap_lookup_by_compatible("brcm,bcm2836-arm-local"); +- if (IS_ERR(intc.local_regmap)) { +- pr_err("Failed to get local register map. FIQ is disabled for cpus > 1\n"); +- intc.local_regmap = NULL; +- } ++ extern void __iomem * __attribute__((weak)) arm_local_intc; ++ intc.local_base = arm_local_intc; ++ if (!intc.local_base) ++ pr_err("Failed to get local intc base. FIQ is disabled for cpus > 1\n"); + } + + /* Make a duplicate irq range which is used to enable FIQ */ +--- a/drivers/irqchip/irq-bcm2836.c ++++ b/drivers/irqchip/irq-bcm2836.c +@@ -22,6 +22,9 @@ struct bcm2836_arm_irqchip_intc { + + static struct bcm2836_arm_irqchip_intc intc __read_mostly; + ++void __iomem *arm_local_intc; ++EXPORT_SYMBOL_GPL(arm_local_intc); ++ + static void bcm2836_arm_irqchip_mask_per_cpu_irq(unsigned int reg_offset, + unsigned int bit, + int cpu) +@@ -323,6 +326,8 @@ static int __init bcm2836_arm_irqchip_l1 + panic("%pOF: unable to map local interrupt registers\n", node); + } + ++ arm_local_intc = intc.base; ++ + bcm2835_init_local_timer_frequency(); + + intc.domain = irq_domain_add_linear(node, LAST_IRQ + 1, diff --git a/target/linux/bcm27xx/patches-5.10/950-0030-lan78xx-Enable-LEDs-and-auto-negotiation.patch b/target/linux/bcm27xx/patches-5.10/950-0030-lan78xx-Enable-LEDs-and-auto-negotiation.patch new file mode 100644 index 0000000000..56f54587a1 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0030-lan78xx-Enable-LEDs-and-auto-negotiation.patch @@ -0,0 +1,48 @@ +From 021908b753875198daddfa9e77a0d2fd8004a469 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 17 Oct 2017 15:04:29 +0100 +Subject: [PATCH] lan78xx: Enable LEDs and auto-negotiation + +For applications of the LAN78xx that don't have valid programmed +EEPROMs or OTPs, enabling both LEDs and auto-negotiation by default +seems reasonable. + +Signed-off-by: Phil Elwell +--- + drivers/net/usb/lan78xx.c | 11 +++++++++++ + 1 file changed, 11 insertions(+) + +--- a/drivers/net/usb/lan78xx.c ++++ b/drivers/net/usb/lan78xx.c +@@ -2453,6 +2453,11 @@ static int lan78xx_reset(struct lan78xx_ + int ret = 0; + unsigned long timeout; + u8 sig; ++ bool has_eeprom; ++ bool has_otp; ++ ++ has_eeprom = !lan78xx_read_eeprom(dev, 0, 0, NULL); ++ has_otp = !lan78xx_read_otp(dev, 0, 0, NULL); + + ret = lan78xx_read_reg(dev, HW_CFG, &buf); + buf |= HW_CFG_LRST_; +@@ -2506,6 +2511,9 @@ static int lan78xx_reset(struct lan78xx_ + + ret = lan78xx_read_reg(dev, HW_CFG, &buf); + buf |= HW_CFG_MEF_; ++ /* If no valid EEPROM and no valid OTP, enable the LEDs by default */ ++ if (!has_eeprom && !has_otp) ++ buf |= HW_CFG_LED0_EN_ | HW_CFG_LED1_EN_; + ret = lan78xx_write_reg(dev, HW_CFG, buf); + + ret = lan78xx_read_reg(dev, USB_CFG0, &buf); +@@ -2561,6 +2569,9 @@ static int lan78xx_reset(struct lan78xx_ + buf |= MAC_CR_AUTO_DUPLEX_ | MAC_CR_AUTO_SPEED_; + } + } ++ /* If no valid EEPROM and no valid OTP, enable AUTO negotiation */ ++ if (!has_eeprom && !has_otp) ++ buf |= MAC_CR_AUTO_DUPLEX_ | MAC_CR_AUTO_SPEED_; + ret = lan78xx_write_reg(dev, MAC_CR, buf); + + ret = lan78xx_read_reg(dev, MAC_TX, &buf); diff --git a/target/linux/bcm27xx/patches-5.10/950-0031-amba_pl011-Don-t-use-DT-aliases-for-numbering.patch b/target/linux/bcm27xx/patches-5.10/950-0031-amba_pl011-Don-t-use-DT-aliases-for-numbering.patch new file mode 100644 index 0000000000..ffd59bc969 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0031-amba_pl011-Don-t-use-DT-aliases-for-numbering.patch @@ -0,0 +1,29 @@ +From a79b4327445a827be28b9939592da8e812a19b29 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 23 Feb 2016 17:26:48 +0000 +Subject: [PATCH] amba_pl011: Don't use DT aliases for numbering + +The pl011 driver looks for DT aliases of the form "serial", +and if found uses as the device ID. This can cause +/dev/ttyAMA0 to become /dev/ttyAMA1, which is confusing if the +other serial port is provided by the 8250 driver which doesn't +use the same logic. +--- + drivers/tty/serial/amba-pl011.c | 5 +++++ + 1 file changed, 5 insertions(+) + +--- a/drivers/tty/serial/amba-pl011.c ++++ b/drivers/tty/serial/amba-pl011.c +@@ -2599,7 +2599,12 @@ static int pl011_setup_port(struct devic + if (IS_ERR(base)) + return PTR_ERR(base); + ++ /* Don't use DT serial aliases - it causes the device to ++ be renumbered to ttyAMA1 if it is the second serial port in the ++ system, even though the other one is ttyS0. The 8250 driver ++ doesn't use this logic, so always remains ttyS0. + index = pl011_probe_dt_alias(index, dev); ++ */ + + uap->old_cr = 0; + uap->port.dev = dev; diff --git a/target/linux/bcm27xx/patches-5.10/950-0032-amba_pl011-Round-input-clock-up.patch b/target/linux/bcm27xx/patches-5.10/950-0032-amba_pl011-Round-input-clock-up.patch new file mode 100644 index 0000000000..9a9b345b67 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0032-amba_pl011-Round-input-clock-up.patch @@ -0,0 +1,86 @@ +From e3f28ae66fd94f4a7a10099a96d6dd5273904943 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 1 Mar 2017 16:07:39 +0000 +Subject: [PATCH] amba_pl011: Round input clock up + +The UART clock is initialised to be as close to the requested +frequency as possible without exceeding it. Now that there is a +clock manager that returns the actual frequencies, an expected +48MHz clock is reported as 47999625. If the requested baudrate +== requested clock/16, there is no headroom and the slight +reduction in actual clock rate results in failure. + +Detect cases where it looks like a "round" clock was chosen and +adjust the reported clock to match that "round" value. As the +code comment says: + +/* + * If increasing a clock by less than 0.1% changes it + * from ..999.. to ..000.., round up. + */ + +Signed-off-by: Phil Elwell +--- + drivers/tty/serial/amba-pl011.c | 23 +++++++++++++++++++++-- + 1 file changed, 21 insertions(+), 2 deletions(-) + +--- a/drivers/tty/serial/amba-pl011.c ++++ b/drivers/tty/serial/amba-pl011.c +@@ -1642,6 +1642,23 @@ static void pl011_put_poll_char(struct u + + #endif /* CONFIG_CONSOLE_POLL */ + ++unsigned long pl011_clk_round(unsigned long clk) ++{ ++ unsigned long scaler; ++ ++ /* ++ * If increasing a clock by less than 0.1% changes it ++ * from ..999.. to ..000.., round up. ++ */ ++ scaler = 1; ++ while (scaler * 100000 < clk) ++ scaler *= 10; ++ if ((clk + scaler - 1)/scaler % 1000 == 0) ++ clk = (clk/scaler + 1) * scaler; ++ ++ return clk; ++} ++ + static int pl011_hwinit(struct uart_port *port) + { + struct uart_amba_port *uap = +@@ -1658,7 +1675,7 @@ static int pl011_hwinit(struct uart_port + if (retval) + return retval; + +- uap->port.uartclk = clk_get_rate(uap->clk); ++ uap->port.uartclk = pl011_clk_round(clk_get_rate(uap->clk)); + + /* Clear pending error and receive interrupts */ + pl011_write(UART011_OEIS | UART011_BEIS | UART011_PEIS | +@@ -2313,7 +2330,7 @@ static int pl011_console_setup(struct co + plat->init(); + } + +- uap->port.uartclk = clk_get_rate(uap->clk); ++ uap->port.uartclk = pl011_clk_round(clk_get_rate(uap->clk)); + + if (uap->vendor->fixed_options) { + baud = uap->fixed_baud; +@@ -2530,6 +2547,7 @@ static struct uart_driver amba_reg = { + .cons = AMBA_CONSOLE, + }; + ++#if 0 + static int pl011_probe_dt_alias(int index, struct device *dev) + { + struct device_node *np; +@@ -2561,6 +2579,7 @@ static int pl011_probe_dt_alias(int inde + + return ret; + } ++#endif + + /* unregisters the driver also if no more ports are left */ + static void pl011_unregister_port(struct uart_amba_port *uap) diff --git a/target/linux/bcm27xx/patches-5.10/950-0033-amba_pl011-Insert-mb-for-correct-FIFO-handling.patch b/target/linux/bcm27xx/patches-5.10/950-0033-amba_pl011-Insert-mb-for-correct-FIFO-handling.patch new file mode 100644 index 0000000000..8a341f2a0c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0033-amba_pl011-Insert-mb-for-correct-FIFO-handling.patch @@ -0,0 +1,27 @@ +From f44d321993ccf1707f5774dc443b900adae5d9d5 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 29 Sep 2017 10:32:19 +0100 +Subject: [PATCH] amba_pl011: Insert mb() for correct FIFO handling + +The pl011 register accessor functions use the _relaxed versions of the +standard readl() and writel() functions, meaning that there are no +automatic memory barriers. When polling a FIFO status register to check +for fullness, it is necessary to ensure that any outstanding writes have +completed; otherwise the flags are effectively stale, making it possible +that the next write is to a full FIFO. + +Signed-off-by: Phil Elwell +--- + drivers/tty/serial/amba-pl011.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/tty/serial/amba-pl011.c ++++ b/drivers/tty/serial/amba-pl011.c +@@ -1377,6 +1377,7 @@ static bool pl011_tx_char(struct uart_am + return false; /* unable to transmit character */ + + pl011_write(c, uap, REG_DR); ++ mb(); + uap->port.icount.tx++; + + return true; diff --git a/target/linux/bcm27xx/patches-5.10/950-0034-amba_pl011-Add-cts-event-workaround-DT-property.patch b/target/linux/bcm27xx/patches-5.10/950-0034-amba_pl011-Add-cts-event-workaround-DT-property.patch new file mode 100644 index 0000000000..08ce5b4bf6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0034-amba_pl011-Add-cts-event-workaround-DT-property.patch @@ -0,0 +1,50 @@ +From 8ccf96729972504acf4ca0e1868278ba549e0f5a Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 29 Sep 2017 10:32:19 +0100 +Subject: [PATCH] amba_pl011: Add cts-event-workaround DT property + +The BCM2835 PL011 implementation seems to have a bug that can lead to a +transmission lockup if CTS changes frequently. A workaround was added to +the driver with a vendor-specific flag to enable it, but this flag is +currently not set for ARM implementations. + +Add a "cts-event-workaround" property to Pi DTBs and use the presence +of that property to force the flag to be enabled in the driver. + +See: https://github.com/raspberrypi/linux/issues/1280 + +Signed-off-by: Phil Elwell +--- + Documentation/devicetree/bindings/serial/pl011.yaml | 6 ++++++ + drivers/tty/serial/amba-pl011.c | 5 +++++ + 2 files changed, 11 insertions(+) + +--- a/Documentation/devicetree/bindings/serial/pl011.yaml ++++ b/Documentation/devicetree/bindings/serial/pl011.yaml +@@ -98,6 +98,12 @@ properties: + $ref: /schemas/types.yaml#/definitions/uint32 + default: 3000 + ++ cts-event-workaround: ++ description: ++ Enables the (otherwise vendor-specific) workaround for the ++ CTS-induced TX lockup. ++ type: boolean ++ + required: + - compatible + - reg +--- a/drivers/tty/serial/amba-pl011.c ++++ b/drivers/tty/serial/amba-pl011.c +@@ -2686,6 +2686,11 @@ static int pl011_probe(struct amba_devic + if (IS_ERR(uap->clk)) + return PTR_ERR(uap->clk); + ++ if (of_property_read_bool(dev->dev.of_node, "cts-event-workaround")) { ++ vendor->cts_event_workaround = true; ++ dev_info(&dev->dev, "cts_event_workaround enabled\n"); ++ } ++ + uap->reg_offset = vendor->reg_offset; + uap->vendor = vendor; + uap->fifosize = vendor->get_fifosize(dev); diff --git a/target/linux/bcm27xx/patches-5.10/950-0035-tty-amba-pl011-Make-TX-optimisation-conditional.patch b/target/linux/bcm27xx/patches-5.10/950-0035-tty-amba-pl011-Make-TX-optimisation-conditional.patch new file mode 100644 index 0000000000..f7316fb3e6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0035-tty-amba-pl011-Make-TX-optimisation-conditional.patch @@ -0,0 +1,85 @@ +From 28c2408f991d97de5e3d1da9711cf5486f411d02 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 11 Jul 2019 13:13:39 +0100 +Subject: [PATCH] tty: amba-pl011: Make TX optimisation conditional + +pl011_tx_chars takes a "from_irq" parameter to reduce the number of +register accesses. When from_irq is true the function assumes that the +FIFO is half empty and writes up to half a FIFO's worth of bytes +without polling the FIFO status register, the reasoning being that +the function is being called as a result of the TX interrupt being +raised. This logic would work were it not for the fact that +pl011_rx_chars, called from pl011_int before pl011_tx_chars, releases +the spinlock before calling tty_flip_buffer_push. + +A user thread writing to the UART claims the spinlock and ultimately +calls pl011_tx_chars with from_irq set to false. This reverts to the +older logic that polls the FIFO status register before sending every +byte. If this happen on an SMP system during the section of the IRQ +handler where the spinlock has been released, then by the time the TX +interrupt handler is called, the FIFO may already be full, and any +further writes are likely to be lost. + +The fix involves adding a per-port flag that is true iff running from +within the interrupt handler and the spinlock has not yet been released. +This flag is then used as the value for the from_irq parameter of +pl011_tx_chars, causing polling to be used in the unsafe case. + +Fixes: 1e84d22322ce ("serial/amba-pl011: Refactor and simplify TX FIFO handling") + +Signed-off-by: Phil Elwell +--- + drivers/tty/serial/amba-pl011.c | 7 ++++++- + 1 file changed, 6 insertions(+), 1 deletion(-) + +--- a/drivers/tty/serial/amba-pl011.c ++++ b/drivers/tty/serial/amba-pl011.c +@@ -265,6 +265,7 @@ struct uart_amba_port { + unsigned int old_cr; /* state during shutdown */ + unsigned int fixed_baud; /* vendor-set fixed baud rate */ + char type[12]; ++ bool irq_locked; /* in irq, unreleased lock */ + #ifdef CONFIG_DMA_ENGINE + /* DMA stuff */ + bool using_tx_dma; +@@ -811,6 +812,7 @@ __acquires(&uap->port.lock) + if (!uap->using_tx_dma) + return; + ++ uap->irq_locked = 0; + dmaengine_terminate_async(uap->dmatx.chan); + + if (uap->dmatx.queued) { +@@ -937,6 +939,7 @@ static void pl011_dma_rx_chars(struct ua + fifotaken = pl011_fifo_to_tty(uap); + } + ++ uap->irq_locked = 0; + spin_unlock(&uap->port.lock); + dev_vdbg(uap->port.dev, + "Took %d chars from DMA buffer and %d chars from the FIFO\n", +@@ -1341,6 +1344,7 @@ __acquires(&uap->port.lock) + { + pl011_fifo_to_tty(uap); + ++ uap->irq_locked = 0; + spin_unlock(&uap->port.lock); + tty_flip_buffer_push(&uap->port.state->port); + /* +@@ -1474,6 +1478,7 @@ static irqreturn_t pl011_int(int irq, vo + int handled = 0; + + spin_lock_irqsave(&uap->port.lock, flags); ++ uap->irq_locked = 1; + status = pl011_read(uap, REG_RIS) & uap->im; + if (status) { + do { +@@ -1493,7 +1498,7 @@ static irqreturn_t pl011_int(int irq, vo + UART011_CTSMIS|UART011_RIMIS)) + pl011_modem_status(uap); + if (status & UART011_TXIS) +- pl011_tx_chars(uap, true); ++ pl011_tx_chars(uap, uap->irq_locked); + + if (pass_counter-- == 0) + break; diff --git a/target/linux/bcm27xx/patches-5.10/950-0036-tty-amba-pl011-Add-un-throttle-support.patch b/target/linux/bcm27xx/patches-5.10/950-0036-tty-amba-pl011-Add-un-throttle-support.patch new file mode 100644 index 0000000000..35d0aba042 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0036-tty-amba-pl011-Add-un-throttle-support.patch @@ -0,0 +1,61 @@ +From 3cec61f1b19a6f589f8b2aef97977e1c38eb7b70 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 24 Jan 2020 11:38:28 +0000 +Subject: [PATCH] tty: amba-pl011: Add un/throttle support + +The PL011 driver lacks throttle and unthrottle methods. As a result, +sending more data to the Pi than it can immediately sink while CRTSCTS +is enabled causes a NULL pointer to be followed. + +Add a throttle handler that disables the RX interrupts, and an +unthrottle handler that reenables them. + +Signed-off-by: Phil Elwell +--- + drivers/tty/serial/amba-pl011.c | 28 ++++++++++++++++++++++++++++ + 1 file changed, 28 insertions(+) + +--- a/drivers/tty/serial/amba-pl011.c ++++ b/drivers/tty/serial/amba-pl011.c +@@ -1317,6 +1317,32 @@ static void pl011_start_tx(struct uart_p + pl011_start_tx_pio(uap); + } + ++static void pl011_throttle(struct uart_port *port) ++{ ++ struct uart_amba_port *uap = ++ container_of(port, struct uart_amba_port, port); ++ unsigned long flags; ++ ++ spin_lock_irqsave(&uap->port.lock, flags); ++ uap->im &= ~(UART011_RTIM | UART011_RXIM); ++ pl011_write(uap->im, uap, REG_IMSC); ++ spin_unlock_irqrestore(&uap->port.lock, flags); ++} ++ ++static void pl011_unthrottle(struct uart_port *port) ++{ ++ struct uart_amba_port *uap = ++ container_of(port, struct uart_amba_port, port); ++ unsigned long flags; ++ ++ spin_lock_irqsave(&uap->port.lock, flags); ++ uap->im |= UART011_RTIM; ++ if (!pl011_dma_rx_running(uap)) ++ uap->im |= UART011_RXIM; ++ pl011_write(uap->im, uap, REG_IMSC); ++ spin_unlock_irqrestore(&uap->port.lock, flags); ++} ++ + static void pl011_stop_rx(struct uart_port *port) + { + struct uart_amba_port *uap = +@@ -2156,6 +2182,8 @@ static const struct uart_ops amba_pl011_ + .stop_tx = pl011_stop_tx, + .start_tx = pl011_start_tx, + .stop_rx = pl011_stop_rx, ++ .throttle = pl011_throttle, ++ .unthrottle = pl011_unthrottle, + .enable_ms = pl011_enable_ms, + .break_ctl = pl011_break_ctl, + .startup = pl011_startup, diff --git a/target/linux/bcm27xx/patches-5.10/950-0037-tty-amba-pl011-Avoid-rare-write-when-full-error.patch b/target/linux/bcm27xx/patches-5.10/950-0037-tty-amba-pl011-Avoid-rare-write-when-full-error.patch new file mode 100644 index 0000000000..8d0ec37042 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0037-tty-amba-pl011-Avoid-rare-write-when-full-error.patch @@ -0,0 +1,42 @@ +From e9addfee683ceabeae5da9dc5503fef536f7385a Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 29 Jan 2020 09:35:19 +0000 +Subject: [PATCH] tty: amba-pl011: Avoid rare write-when-full error + +Under some circumstances on BCM283x processors data loss can be +observed - a single byte missing from the TX output stream. These bytes +are always the last byte of a batch of 8 written from pl011_tx_chars +when from_irq is true, meaning that the FIFO full flag is not checked +before writing. + +The transmit optimisation relies on the FIFO being half-empty when the +TX interrupt is raised. Instrumenting the driver further showed that +the failure case correlated with the TX FIFO full flag being set at the +point where the last byte was written to the data register, which +explains the data loss but not how the FIFO appeared to be prematurely +full. A possible explanation is that a FIFO write was in flight at the +time the interrupt was raised, but as yet there is no hypothesis as to +how this might occur. + +In the absence of a clear understanding of the failure mechanism, avoid +the problem by checking the FIFO levels before writing the last byte of +the group, which will have minimal performance impact. + +Signed-off-by: Phil Elwell +--- + drivers/tty/serial/amba-pl011.c | 4 ++++ + 1 file changed, 4 insertions(+) + +--- a/drivers/tty/serial/amba-pl011.c ++++ b/drivers/tty/serial/amba-pl011.c +@@ -1438,6 +1438,10 @@ static bool pl011_tx_chars(struct uart_a + if (likely(from_irq) && count-- == 0) + break; + ++ if (likely(from_irq) && count == 0 && ++ pl011_read(uap, REG_FR) & UART01x_FR_TXFF) ++ break; ++ + if (!pl011_tx_char(uap, xmit->buf[xmit->tail], from_irq)) + break; + diff --git a/target/linux/bcm27xx/patches-5.10/950-0038-pinctrl-bcm2835-Set-base-to-0-give-expected-gpio-num.patch b/target/linux/bcm27xx/patches-5.10/950-0038-pinctrl-bcm2835-Set-base-to-0-give-expected-gpio-num.patch new file mode 100644 index 0000000000..d8bb4c1f73 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0038-pinctrl-bcm2835-Set-base-to-0-give-expected-gpio-num.patch @@ -0,0 +1,22 @@ +From 68ef623a719071e05f5d62270c7bee35a2984452 Mon Sep 17 00:00:00 2001 +From: notro +Date: Thu, 10 Jul 2014 13:59:47 +0200 +Subject: [PATCH] pinctrl-bcm2835: Set base to 0 give expected gpio + numbering + +Signed-off-by: Noralf Tronnes +--- + drivers/pinctrl/bcm/pinctrl-bcm2835.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c ++++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c +@@ -362,7 +362,7 @@ static const struct gpio_chip bcm2835_gp + .get = bcm2835_gpio_get, + .set = bcm2835_gpio_set, + .set_config = gpiochip_generic_config, +- .base = -1, ++ .base = 0, + .ngpio = BCM2835_NUM_GPIOS, + .can_sleep = false, + }; diff --git a/target/linux/bcm27xx/patches-5.10/950-0039-Main-bcm2708-bcm2709-linux-port.patch b/target/linux/bcm27xx/patches-5.10/950-0039-Main-bcm2708-bcm2709-linux-port.patch new file mode 100644 index 0000000000..ec4df9cbae --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0039-Main-bcm2708-bcm2709-linux-port.patch @@ -0,0 +1,150 @@ +From 0ef60858b9927024cd310038c97976e27e4daada Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Sun, 12 May 2013 12:24:19 +0100 +Subject: [PATCH] Main bcm2708/bcm2709 linux port +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: popcornmix +Signed-off-by: Noralf Trønnes + +bcm2709: Drop platform smp and timer init code + +irq-bcm2836 handles this through these functions: +bcm2835_init_local_timer_frequency() +bcm2836_arm_irqchip_smp_init() + +Signed-off-by: Noralf Trønnes + +bcm270x: Use watchdog for reboot/poweroff + +The watchdog driver already has support for reboot/poweroff. +Make use of this and remove the code from the platform files. + +Signed-off-by: Noralf Trønnes + +board_bcm2835: Remove coherent dma pool increase - API has gone +--- + arch/arm/mach-bcm/Kconfig | 1 + + arch/arm/mm/proc-v6.S | 15 ++++++++++++--- + drivers/irqchip/irq-bcm2835.c | 7 ++++++- + drivers/mailbox/bcm2835-mailbox.c | 18 ++++++++++++++++-- + 4 files changed, 35 insertions(+), 6 deletions(-) + +--- a/arch/arm/mach-bcm/Kconfig ++++ b/arch/arm/mach-bcm/Kconfig +@@ -165,6 +165,7 @@ config ARCH_BCM2835 + select PINCTRL + select PINCTRL_BCM2835 + select MFD_CORE ++ select MFD_SYSCON if ARCH_MULTI_V7 + help + This enables support for the Broadcom BCM2711 and BCM283x SoCs. + This SoC is used in the Raspberry Pi and Roku 2 devices. +--- a/arch/arm/mm/proc-v6.S ++++ b/arch/arm/mm/proc-v6.S +@@ -70,10 +70,19 @@ ENDPROC(cpu_v6_reset) + * + * IRQs are already disabled. + */ ++ ++/* See jira SW-5991 for details of this workaround */ + ENTRY(cpu_v6_do_idle) +- mov r1, #0 +- mcr p15, 0, r1, c7, c10, 4 @ DWB - WFI may enter a low-power mode +- mcr p15, 0, r1, c7, c0, 4 @ wait for interrupt ++ .align 5 ++ mov r1, #2 ++1: subs r1, #1 ++ nop ++ mcreq p15, 0, r1, c7, c10, 4 @ DWB - WFI may enter a low-power mode ++ mcreq p15, 0, r1, c7, c0, 4 @ wait for interrupt ++ nop ++ nop ++ nop ++ bne 1b + ret lr + + ENTRY(cpu_v6_dcache_clean_area) +--- a/drivers/irqchip/irq-bcm2835.c ++++ b/drivers/irqchip/irq-bcm2835.c +@@ -43,7 +43,9 @@ + #include + + #include ++#ifndef CONFIG_ARM64 + #include ++#endif + + /* Put the bank and irq (32 bits) into the hwirq */ + #define MAKE_HWIRQ(b, n) (((b) << 5) | (n)) +@@ -72,6 +74,7 @@ + #define NR_BANKS 3 + #define IRQS_PER_BANK 32 + #define NUMBER_IRQS MAKE_HWIRQ(NR_BANKS, 0) ++#undef FIQ_START + #define FIQ_START (NR_IRQS_BANK0 + MAKE_HWIRQ(NR_BANKS - 1, 0)) + + static const int reg_pending[] __initconst = { 0x00, 0x04, 0x08 }; +@@ -253,10 +256,12 @@ static int __init armctrl_of_init(struct + MAKE_HWIRQ(b, i) + NUMBER_IRQS); + BUG_ON(irq <= 0); + irq_set_chip(irq, &armctrl_chip); +- set_irq_flags(irq, IRQF_VALID | IRQF_PROBE); ++ irq_set_probe(irq); + } + } ++#ifndef CONFIG_ARM64 + init_FIQ(FIQ_START); ++#endif + + return 0; + } +--- a/drivers/mailbox/bcm2835-mailbox.c ++++ b/drivers/mailbox/bcm2835-mailbox.c +@@ -45,12 +45,15 @@ + #define MAIL1_WRT (ARM_0_MAIL1 + 0x00) + #define MAIL1_STA (ARM_0_MAIL1 + 0x18) + ++/* On ARCH_BCM270x these come through (arm_control.h ) */ ++#ifndef ARM_MS_FULL + /* Status register: FIFO state. */ + #define ARM_MS_FULL BIT(31) + #define ARM_MS_EMPTY BIT(30) + + /* Configuration register: Enable interrupts. */ + #define ARM_MC_IHAVEDATAIRQEN BIT(0) ++#endif + + struct bcm2835_mbox { + void __iomem *regs; +@@ -145,7 +148,7 @@ static int bcm2835_mbox_probe(struct pla + return -ENOMEM; + spin_lock_init(&mbox->lock); + +- ret = devm_request_irq(dev, irq_of_parse_and_map(dev->of_node, 0), ++ ret = devm_request_irq(dev, platform_get_irq(pdev, 0), + bcm2835_mbox_irq, 0, dev_name(dev), mbox); + if (ret) { + dev_err(dev, "Failed to register a mailbox IRQ handler: %d\n", +@@ -195,7 +198,18 @@ static struct platform_driver bcm2835_mb + }, + .probe = bcm2835_mbox_probe, + }; +-module_platform_driver(bcm2835_mbox_driver); ++ ++static int __init bcm2835_mbox_init(void) ++{ ++ return platform_driver_register(&bcm2835_mbox_driver); ++} ++arch_initcall(bcm2835_mbox_init); ++ ++static void __init bcm2835_mbox_exit(void) ++{ ++ platform_driver_unregister(&bcm2835_mbox_driver); ++} ++module_exit(bcm2835_mbox_exit); + + MODULE_AUTHOR("Lubomir Rintel "); + MODULE_DESCRIPTION("BCM2835 mailbox IPC driver"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0040-Add-dwc_otg-driver.patch b/target/linux/bcm27xx/patches-5.10/950-0040-Add-dwc_otg-driver.patch new file mode 100644 index 0000000000..754dd45aa5 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0040-Add-dwc_otg-driver.patch @@ -0,0 +1,61618 @@ +From 8c7c80cd6068b80a4bde7276ff79964de48d4ed0 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Wed, 1 May 2013 19:46:17 +0100 +Subject: [PATCH] Add dwc_otg driver +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: popcornmix + +usb: dwc: fix lockdep false positive + +Signed-off-by: Kari Suvanto + +usb: dwc: fix inconsistent lock state + +Signed-off-by: Kari Suvanto + +Add FIQ patch to dwc_otg driver. Enable with dwc_otg.fiq_fix_enable=1. Should give about 10% more ARM performance. +Thanks to Gordon and Costas + +Avoid dynamic memory allocation for channel lock in USB driver. Thanks ddv2005. + +Add NAK holdoff scheme. Enabled by default, disable with dwc_otg.nak_holdoff_enable=0. Thanks gsh + +Make sure we wait for the reset to finish + +dwc_otg: fix bug in dwc_otg_hcd.c resulting in silent kernel + memory corruption, escalating to OOPS under high USB load. + +dwc_otg: Fix unsafe access of QTD during URB enqueue + +In dwc_otg_hcd_urb_enqueue during qtd creation, it was possible that the +transaction could complete almost immediately after the qtd was assigned +to a host channel during URB enqueue, which meant the qtd pointer was no +longer valid having been completed and removed. Usually, this resulted in +an OOPS during URB submission. By predetermining whether transactions +need to be queued or not, this unsafe pointer access is avoided. + +This bug was only evident on the Pi model A where a device was attached +that had no periodic endpoints (e.g. USB pendrive or some wlan devices). + +dwc_otg: Fix incorrect URB allocation error handling + +If the memory allocation for a dwc_otg_urb failed, the kernel would OOPS +because for some reason a member of the *unallocated* struct was set to +zero. Error handling changed to fail correctly. + +dwc_otg: fix potential use-after-free case in interrupt handler + +If a transaction had previously aborted, certain interrupts are +enabled to track error counts and reset where necessary. On IN +endpoints the host generates an ACK interrupt near-simultaneously +with completion of transfer. In the case where this transfer had +previously had an error, this results in a use-after-free on +the QTD memory space with a 1-byte length being overwritten to +0x00. + +dwc_otg: add handling of SPLIT transaction data toggle errors + +Previously a data toggle error on packets from a USB1.1 device behind +a TT would result in the Pi locking up as the driver never handled +the associated interrupt. Patch adds basic retry mechanism and +interrupt acknowledgement to cater for either a chance toggle error or +for devices that have a broken initial toggle state (FT8U232/FT232BM). + +dwc_otg: implement tasklet for returning URBs to usbcore hcd layer + +The dwc_otg driver interrupt handler for transfer completion will spend +a very long time with interrupts disabled when a URB is completed - +this is because usb_hcd_giveback_urb is called from within the handler +which for a USB device driver with complicated processing (e.g. webcam) +will take an exorbitant amount of time to complete. This results in +missed completion interrupts for other USB packets which lead to them +being dropped due to microframe overruns. + +This patch splits returning the URB to the usb hcd layer into a +high-priority tasklet. This will have most benefit for isochronous IN +transfers but will also have incidental benefit where multiple periodic +devices are active at once. + +dwc_otg: fix NAK holdoff and allow on split transactions only + +This corrects a bug where if a single active non-periodic endpoint +had at least one transaction in its qh, on frnum == MAX_FRNUM the qh +would get skipped and never get queued again. This would result in +a silent device until error detection (automatic or otherwise) would +either reset the device or flush and requeue the URBs. + +Additionally the NAK holdoff was enabled for all transactions - this +would potentially stall a HS endpoint for 1ms if a previous error state +enabled this interrupt and the next response was a NAK. Fix so that +only split transactions get held off. + +dwc_otg: Call usb_hcd_unlink_urb_from_ep with lock held in completion handler + +usb_hcd_unlink_urb_from_ep must be called with the HCD lock held. Calling it +asynchronously in the tasklet was not safe (regression in +c4564d4a1a0a9b10d4419e48239f5d99e88d2667). + +This change unlinks it from the endpoint prior to queueing it for handling in +the tasklet, and also adds a check to ensure the urb is OK to be unlinked +before doing so. + +NULL pointer dereference kernel oopses had been observed in usb_hcd_giveback_urb +when a USB device was unplugged/replugged during data transfer. This effect +was reproduced using automated USB port power control, hundreds of replug +events were performed during active transfers to confirm that the problem was +eliminated. + +USB fix using a FIQ to implement split transactions + +This commit adds a FIQ implementaion that schedules +the split transactions using a FIQ so we don't get +held off by the interrupt latency of Linux + +dwc_otg: fix device attributes and avoid kernel warnings on boot + +dcw_otg: avoid logging function that can cause panics + +See: https://github.com/raspberrypi/firmware/issues/21 +Thanks to cleverca22 for fix + +dwc_otg: mask correct interrupts after transaction error recovery + +The dwc_otg driver will unmask certain interrupts on a transaction +that previously halted in the error state in order to reset the +QTD error count. The various fine-grained interrupt handlers do not +consider that other interrupts besides themselves were unmasked. + +By disabling the two other interrupts only ever enabled in DMA mode +for this purpose, we can avoid unnecessary function calls in the +IRQ handler. This will also prevent an unneccesary FIQ interrupt +from being generated if the FIQ is enabled. + +dwc_otg: fiq: prevent FIQ thrash and incorrect state passing to IRQ + +In the case of a transaction to a device that had previously aborted +due to an error, several interrupts are enabled to reset the error +count when a device responds. This has the side-effect of making the +FIQ thrash because the hardware will generate multiple instances of +a NAK on an IN bulk/interrupt endpoint and multiple instances of ACK +on an OUT bulk/interrupt endpoint. Make the FIQ mask and clear the +associated interrupts. + +Additionally, on non-split transactions make sure that only unmasked +interrupts are cleared. This caused a hard-to-trigger but serious +race condition when you had the combination of an endpoint awaiting +error recovery and a transaction completed on an endpoint - due to +the sequencing and timing of interrupts generated by the dwc_otg core, +it was possible to confuse the IRQ handler. + +Fix function tracing + +dwc_otg: whitespace cleanup in dwc_otg_urb_enqueue + +dwc_otg: prevent OOPSes during device disconnects + +The dwc_otg_urb_enqueue function is thread-unsafe. In particular the +access of urb->hcpriv, usb_hcd_link_urb_to_ep, dwc_otg_urb->qtd and +friends does not occur within a critical section and so if a device +was unplugged during activity there was a high chance that the +usbcore hub_thread would try to disable the endpoint with partially- +formed entries in the URB queue. This would result in BUG() or null +pointer dereferences. + +Fix so that access of urb->hcpriv, enqueuing to the hardware and +adding to usbcore endpoint URB lists is contained within a single +critical section. + +dwc_otg: prevent BUG() in TT allocation if hub address is > 16 + +A fixed-size array is used to track TT allocation. This was +previously set to 16 which caused a crash because +dwc_otg_hcd_allocate_port would read past the end of the array. + +This was hit if a hub was plugged in which enumerated as addr > 16, +due to previous device resets or unplugs. + +Also add #ifdef FIQ_DEBUG around hcd->hub_port_alloc[], which grows +to a large size if 128 hub addresses are supported. This field is +for debug only for tracking which frame an allocate happened in. + +dwc_otg: make channel halts with unknown state less damaging + +If the IRQ received a channel halt interrupt through the FIQ +with no other bits set, the IRQ would not release the host +channel and never complete the URB. + +Add catchall handling to treat as a transaction error and retry. + +dwc_otg: fiq_split: use TTs with more granularity + +This fixes certain issues with split transaction scheduling. + +- Isochronous multi-packet OUT transactions now hog the TT until + they are completed - this prevents hubs aborting transactions + if they get a periodic start-split out-of-order +- Don't perform TT allocation on non-periodic endpoints - this + allows simultaneous use of the TT's bulk/control and periodic + transaction buffers + +This commit will mainly affect USB audio playback. + +dwc_otg: fix potential sleep while atomic during urb enqueue + +Fixes a regression introduced with eb1b482a. Kmalloc called from +dwc_otg_hcd_qtd_add / dwc_otg_hcd_qtd_create did not always have +the GPF_ATOMIC flag set. Force this flag when inside the larger +critical section. + +dwc_otg: make fiq_split_enable imply fiq_fix_enable + +Failing to set up the FIQ correctly would result in +"IRQ 32: nobody cared" errors in dmesg. + +dwc_otg: prevent crashes on host port disconnects + +Fix several issues resulting in crashes or inconsistent state +if a Model A root port was disconnected. + +- Clean up queue heads properly in kill_urbs_in_qh_list by + removing the empty QHs from the schedule lists +- Set the halt status properly to prevent IRQ handlers from + using freed memory +- Add fiq_split related cleanup for saved registers +- Make microframe scheduling reclaim host channels if + active during a disconnect +- Abort URBs with -ESHUTDOWN status response, informing + device drivers so they respond in a more correct fashion + and don't try to resubmit URBs +- Prevent IRQ handlers from attempting to handle channel + interrupts if the associated URB was dequeued (and the + driver state was cleared) + +dwc_otg: prevent leaking URBs during enqueue + +A dwc_otg_urb would get leaked if the HCD enqueue function +failed for any reason. Free the URB at the appropriate points. + +dwc_otg: Enable NAK holdoff for control split transactions + +Certain low-speed devices take a very long time to complete a +data or status stage of a control transaction, producing NAK +responses until they complete internal processing - the USB2.0 +spec limit is up to 500mS. This causes the same type of interrupt +storm as seen with USB-serial dongles prior to c8edb238. + +In certain circumstances, usually while booting, this interrupt +storm could cause SD card timeouts. + +dwc_otg: Fix for occasional lockup on boot when doing a USB reset + +dwc_otg: Don't issue traffic to LS devices in FS mode + +Issuing low-speed packets when the root port is in full-speed mode +causes the root port to stop responding. Explicitly fail when +enqueuing URBs to a LS endpoint on a FS bus. + +Fix ARM architecture issue with local_irq_restore() + +If local_fiq_enable() is called before a local_irq_restore(flags) where +the flags variable has the F bit set, the FIQ will be erroneously disabled. + +Fixup arch_local_irq_restore to avoid trampling the F bit in CPSR. + +Also fix some of the hacks previously implemented for previous dwc_otg +incarnations. + +dwc_otg: fiq_fsm: Base commit for driver rewrite + +This commit removes the previous FIQ fixes entirely and adds fiq_fsm. + +This rewrite features much more complete support for split transactions +and takes into account several OTG hardware bugs. High-speed +isochronous transactions are also capable of being performed by fiq_fsm. + +All driver options have been removed and replaced with: + - dwc_otg.fiq_enable (bool) + - dwc_otg.fiq_fsm_enable (bool) + - dwc_otg.fiq_fsm_mask (bitmask) + - dwc_otg.nak_holdoff (unsigned int) + +Defaults are specified such that fiq_fsm behaves similarly to the +previously implemented FIQ fixes. + +fiq_fsm: Push error recovery into the FIQ when fiq_fsm is used + +If the transfer associated with a QTD failed due to a bus error, the HCD +would retry the transfer up to 3 times (implementing the USB2.0 +three-strikes retry in software). + +Due to the masking mechanism used by fiq_fsm, it is only possible to pass +a single interrupt through to the HCD per-transfer. + +In this instance host channels would fall off the radar because the error +reset would function, but the subsequent channel halt would be lost. + +Push the error count reset into the FIQ handler. + +fiq_fsm: Implement timeout mechanism + +For full-speed endpoints with a large packet size, interrupt latency +runs the risk of the FIQ starting a transaction too late in a full-speed +frame. If the device is still transmitting data when EOF2 for the +downstream frame occurs, the hub will disable the port. This change is +not reflected in the hub status endpoint and the device becomes +unresponsive. + +Prevent high-bandwidth transactions from being started too late in a +frame. The mechanism is not guaranteed: a combination of bit stuffing +and hub latency may still result in a device overrunning. + +fiq_fsm: fix bounce buffer utilisation for Isochronous OUT + +Multi-packet isochronous OUT transactions were subject to a few bounday +bugs. Fix them. + +Audio playback is now much more robust: however, an issue stands with +devices that have adaptive sinks - ALSA plays samples too fast. + +dwc_otg: Return full-speed frame numbers in HS mode + +The frame counter increments on every *microframe* in high-speed mode. +Most device drivers expect this number to be in full-speed frames - this +caused considerable confusion to e.g. snd_usb_audio which uses the +frame counter to estimate the number of samples played. + +fiq_fsm: save PID on completion of interrupt OUT transfers + +Also add edge case handling for interrupt transports. + +Note that for periodic split IN, data toggles are unimplemented in the +OTG host hardware - it unconditionally accepts any PID. + +fiq_fsm: add missing case for fiq_fsm_tt_in_use() + +Certain combinations of bitrate and endpoint activity could +result in a periodic transaction erroneously getting started +while the previous Isochronous OUT was still active. + +fiq_fsm: clear hcintmsk for aborted transactions + +Prevents the FIQ from erroneously handling interrupts +on a timed out channel. + +fiq_fsm: enable by default + +fiq_fsm: fix dequeues for non-periodic split transactions + +If a dequeue happened between the SSPLIT and CSPLIT phases of the +transaction, the HCD would never receive an interrupt. + +fiq_fsm: Disable by default + +fiq_fsm: Handle HC babble errors + +The HCTSIZ transfer size field raises a babble interrupt if +the counter wraps. Handle the resulting interrupt in this case. + +dwc_otg: fix interrupt registration for fiq_enable=0 + +Additionally make the module parameter conditional for wherever +hcd->fiq_state is touched. + +fiq_fsm: Enable by default + +dwc_otg: Fix various issues with root port and transaction errors + +Process the host port interrupts correctly (and don't trample them). +Root port hotplug now functional again. + +Fix a few thinkos with the transaction error passthrough for fiq_fsm. + +fiq_fsm: Implement hack for Split Interrupt transactions + +Hubs aren't too picky about which endpoint we send Control type split +transactions to. By treating Interrupt transfers as Control, it is +possible to use the non-periodic queue in the OTG core as well as the +non-periodic FIFOs in the hub itself. This massively reduces the +microframe exclusivity/contention that periodic split transactions +otherwise have to enforce. + +It goes without saying that this is a fairly egregious USB specification +violation, but it works. + +Original idea by Hans Petter Selasky @ FreeBSD.org. + +dwc_otg: FIQ support on SMP. Set up FIQ stack and handler on Core 0 only. + +dwc_otg: introduce fiq_fsm_spin(un|)lock() + +SMP safety for the FIQ relies on register read-modify write cycles being +completed in the correct order. Several places in the DWC code modify +registers also touched by the FIQ. Protect these by a bare-bones lock +mechanism. + +This also makes it possible to run the FIQ and IRQ handlers on different +cores. + +fiq_fsm: fix build on bcm2708 and bcm2709 platforms + +dwc_otg: put some barriers back where they should be for UP + +bcm2709/dwc_otg: Setup FIQ on core 1 if >1 core active + +dwc_otg: fixup read-modify-write in critical paths + +Be more careful about read-modify-write on registers that the FIQ +also touches. + +Guard fiq_fsm_spin_lock with fiq_enable check + +fiq_fsm: Falling out of the state machine isn't fatal + +This edge case can be hit if the port is disabled while the FIQ is +in the middle of a transaction. Make the effects less severe. + +Also get rid of the useless return value. + +squash: dwc_otg: Allow to build without SMP + +usb: core: make overcurrent messages more prominent + +Hub overcurrent messages are more serious than "debug". Increase loglevel. + +usb: dwc_otg: Don't use dma_to_virt() + +Commit 6ce0d20 changes dma_to_virt() which breaks this driver. +Open code the old dma_to_virt() implementation to work around this. + +Limit the use of __bus_to_virt() to cases where transfer_buffer_length +is set and transfer_buffer is not set. This is done to increase the +chance that this driver will also work on ARCH_BCM2835. + +transfer_buffer should not be NULL if the length is set, but the +comment in the code indicates that there are situations where this +might happen. drivers/usb/isp1760/isp1760-hcd.c also has a similar +comment pointing to a possible: 'usb storage / SCSI bug'. + +Signed-off-by: Noralf Trønnes + +dwc_otg: Fix crash when fiq_enable=0 + +dwc_otg: fiq_fsm: Make high-speed isochronous strided transfers work properly + +Certain low-bandwidth high-speed USB devices (specialist audio devices, +compressed-frame webcams) have packet intervals > 1 microframe. + +Stride these transfers in the FIQ by using the start-of-frame interrupt +to restart the channel at the right time. + +dwc_otg: Force host mode to fix incorrect compute module boards + +dwc_otg: Add ARCH_BCM2835 support + +Signed-off-by: Noralf Trønnes + +dwc_otg: Simplify FIQ irq number code + +Dropping ATAGS means we can simplify the FIQ irq number code. +Also add error checking on the returned irq number. + +Signed-off-by: Noralf Trønnes + +dwc_otg: Remove duplicate gadget probe/unregister function + +dwc_otg: Properly set the HFIR + +Douglas Anderson reported: + +According to the most up to date version of the dwc2 databook, the FRINT +field of the HFIR register should be programmed to: +* 125 us * (PHY clock freq for HS) - 1 +* 1000 us * (PHY clock freq for FS/LS) - 1 + +This is opposed to older versions of the doc that claimed it should be: +* 125 us * (PHY clock freq for HS) +* 1000 us * (PHY clock freq for FS/LS) + +and reported lower timing jitter on a USB analyser + +dcw_otg: trim xfer length when buffer larger than allocated size is received + +dwc_otg: Don't free qh align buffers in atomic context + +dwc_otg: Enable the hack for Split Interrupt transactions by default + +dwc_otg.fiq_fsm_mask=0xF has long been a suggestion for users with audio stutters or other USB bandwidth issues. +So far we are aware of many success stories but no failure caused by this setting. +Make it a default to learn more. + +See: https://www.raspberrypi.org/forums/viewtopic.php?f=28&t=70437 + +Signed-off-by: popcornmix + +dwc_otg: Use kzalloc when suitable + +dwc_otg: Pass struct device to dma_alloc*() + +This makes it possible to get the bus address from Device Tree. + +Signed-off-by: Noralf Trønnes + +dwc_otg: fix summarize urb->actual_length for isochronous transfers + +Kernel does not copy input data of ISO transfers to userspace +if actual_length is set only in ISO transfers and not summarized +in urb->actual_length. Fixes raspberrypi/linux#903 + +fiq_fsm: Use correct states when starting isoc OUT transfers + +In fiq_fsm_start_next_periodic() if an isochronous OUT transfer +was selected, no regard was given as to whether this was a single-packet +transfer or a multi-packet staged transfer. + +For single-packet transfers, this had the effect of repeatedly sending +OUT packets with bogus data and lengths. + +Eventually if the channel was repeatedly enabled enough times, this +would lock up the OTG core and no further bus transfers would happen. + +Set the FSM state up properly if we select a single-packet transfer. + +Fixes https://github.com/raspberrypi/linux/issues/1842 + +dwc_otg: make nak_holdoff work as intended with empty queues + +If URBs reading from non-periodic split endpoints were dequeued and +the last transfer from the endpoint was a NAK handshake, the resulting +qh->nak_frame value was stale which would result in unnecessarily long +polling intervals for the first subsequent transfer with a fresh URB. + +Fixup qh->nak_frame in dwc_otg_hcd_urb_dequeue and also guard against +a case where a single URB is submitted to the endpoint, a NAK was +received on the transfer immediately prior to receiving data and the +device subsequently resubmits another URB past the qh->nak_frame interval. + +Fixes https://github.com/raspberrypi/linux/issues/1709 + +dwc_otg: fix split transaction data toggle handling around dequeues + +See https://github.com/raspberrypi/linux/issues/1709 + +Fix several issues regarding endpoint state when URBs are dequeued +- If the HCD is disconnected, flush FIQ-enabled channels properly +- Save the data toggle state for bulk endpoints if the last transfer + from an endpoint where URBs were dequeued returned a data packet +- Reset hc->start_pkt_count properly in assign_and_init_hc() + +dwc_otg: fix several potential crash sources + +On root port disconnect events, the host driver state is cleared and +in-progress host channels are forcibly stopped. This doesn't play +well with the FIQ running in the background, so: +- Guard the disconnect callback with both the host spinlock and FIQ + spinlock +- Move qtd dereference in dwc_otg_handle_hc_fsm() after the early-out + so we don't dereference a qtd that has gone away +- Turn catch-all BUG()s in dwc_otg_handle_hc_fsm() into warnings. + +dwc_otg: delete hcd->channel_lock + +The lock serves no purpose as it is only held while the HCD spinlock +is already being held. + +dwc_otg: remove unnecessary dma-mode channel halts on disconnect interrupt + +Host channels are already halted in kill_urbs_in_qh_list() with the +subsequent interrupt processing behaving as if the URB was dequeued +via HCD callback. + +There's no need to clobber the host channel registers a second time +as this exposes races between the driver and host channel resulting +in hcd->free_hc_list becoming corrupted. + +dwcotg: Allow to build without FIQ on ARM64 + +Signed-off-by: popcornmix + +dwc_otg: make periodic scheduling behave properly for FS buses + +If the root port is in full-speed mode, transfer times at 12mbit/s +would be calculated but matched against high-speed quotas. + +Reinitialise hcd->frame_usecs[i] on each port enable event so that +full-speed bandwidth can be tracked sensibly. + +Also, don't bother using the FIQ for transfers when in full-speed +mode - at the slower bus speed, interrupt frequency is reduced by +an order of magnitude. + +Related issue: https://github.com/raspberrypi/linux/issues/2020 + +dwc_otg: fiq_fsm: Make isochronous compatibility checks work properly + +Get rid of the spammy printk and local pointer mangling. +Also, there is a nominal benefit for using fiq_fsm for isochronous +transfers in FS mode (~1.1k IRQs per second vs 2.1k IRQs per second) +so remove the root port speed check. + +dwc_otg: add module parameter int_ep_interval_min + +Add a module parameter (defaulting to ignored) that clamps the polling rate +of high-speed Interrupt endpoints to a minimum microframe interval. + +The parameter is modifiable at runtime as it is used when activating new +endpoints (such as on device connect). + +dwc_otg: fiq_fsm: Add non-periodic TT exclusivity constraints + +Certain hub types do not discriminate between pipe direction (IN or OUT) +when considering non-periodic transfers. Therefore these hubs get confused +if multiple transfers are issued in different directions with the same +device address and endpoint number. + +Constrain queuing non-periodic split transactions so they are performed +serially in such cases. + +Related: https://github.com/raspberrypi/linux/issues/2024 + +dwc_otg: Fixup change to DRIVER_ATTR interface + +dwc_otg: Fix compilation warnings + +Signed-off-by: Phil Elwell + +USB_DWCOTG: Disable building dwc_otg as a module (#2265) + +When dwc_otg is built as a module, build will fail with the following +error: + +ERROR: "DWC_TASK_HI_SCHEDULE" [drivers/usb/host/dwc_otg/dwc_otg.ko] undefined! +scripts/Makefile.modpost:91: recipe for target '__modpost' failed +make[1]: *** [__modpost] Error 1 +Makefile:1199: recipe for target 'modules' failed +make: *** [modules] Error 2 + +Even if the error is solved by including the missing +DWC_TASK_HI_SCHEDULE function, the kernel will panic when loading +dwc_otg. + +As a workaround, simply prevent user from building dwc_otg as a module +as the current kernel does not support it. + +See: https://github.com/raspberrypi/linux/issues/2258 + +Signed-off-by: Malik Olivier Boussejra + +dwc_otg: New timer API + +dwc_otg: Fix removed ACCESS_ONCE->READ_ONCE + +dwc_otg: don't unconditionally force host mode in dwc_otg_cil_init() + +Add the ability to disable force_host_mode for those that want to use +dwc_otg in both device and host modes. + +dwc_otg: Fix a regression when dequeueing isochronous transfers + +In 282bed95 (dwc_otg: make nak_holdoff work as intended with empty queues) +the dequeue mechanism was changed to leave FIQ-enabled transfers to run +to completion - to avoid leaving hub TT buffers with stale packets lying +around. + +This broke FIQ-accelerated isochronous transfers, as this then meant that +dozens of transfers were performed after the dequeue function returned. + +Restore the state machine fence for isochronous transfers. + +fiq_fsm: rewind DMA pointer for OUT transactions that fail (#2288) + +See: https://github.com/raspberrypi/linux/issues/2140 + +dwc_otg: add smp_mb() to prevent driver state corruption on boot + +Occasional crashes have been seen where the FIQ code dereferences +invalid/random pointers immediately after being set up, leading to +panic on boot. + +The crash occurs as the FIQ code races against hcd_init_fiq() and +the hcd_init_fiq() code races against the outstanding memory stores +from dwc_otg_hcd_init(). Use explicit barriers after touching +driver state. + +usb: dwc_otg: fix memory corruption in dwc_otg driver + +[Upstream commit 51b1b6491752ac066ee8d32cc66042fcc955fef6] + +The move from the staging tree to the main tree exposed a +longstanding memory corruption bug in the dwc2 driver. The +reordering of the driver initialization caused the dwc2 driver +to corrupt the initialization data of the sdhci driver on the +Raspberry Pi platform, which made the bug show up. + +The error is in calling to_usb_device(hsotg->dev), since ->dev +is not a member of struct usb_device. The easiest fix is to +just remove the offending code, since it is not really needed. + +Thanks to Stephen Warren for tracking down the cause of this. + +Reported-by: Andre Heider +Tested-by: Stephen Warren +Signed-off-by: Paul Zimmerman +Signed-off-by: Greg Kroah-Hartman +[lukas: port from upstream dwc2 to out-of-tree dwc_otg driver] +Signed-off-by: Lukas Wunner + +usb: dwb_otg: Fix unreachable switch statement warning + +This warning appears with GCC 7.3.0 from toolchains.bootlin.com: + +../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c: In function ‘fiq_fsm_update_hs_isoc’: +../drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c:595:61: warning: statement will never be executed [-Wswitch-unreachable] + st->hctsiz_copy.b.xfersize = nrpackets * st->hcchar_copy.b.mps; + ~~~~~~~~~~~~~~~~~^~~~ + +Signed-off-by: Nathan Chancellor + +dwc_otg: fiq_fsm: fix incorrect DMA register offset calculation + +Rationalise the offset and update all call sites. + +Fixes https://github.com/raspberrypi/linux/issues/2408 + +dwc_otg: fix bug with port_addr assignment for single-TT hubs + +See https://github.com/raspberrypi/linux/issues/2734 + +The "Hub Port" field in the split transaction packet was always set +to 1 for single-TT hubs. The majority of single-TT hub products +apparently ignore this field and broadcast to all downstream enabled +ports, which masked the issue. A subset of hub devices apparently +need the port number to be exact or split transactions will fail. + +usb: dwc_otg: Clean up build warnings on 64bit kernels + +No functional changes. Almost all are changes to logging lines. + +Signed-off-by: Dave Stevenson + +usb: dwc_otg: Use dma allocation for mphi dummy_send buffer + +The FIQ driver used a kzalloc'ed buffer for dummy_send, +passing a kernel virtual address to the hardware block. +The buffer is only ever used for a dummy read, so it +should be harmless, but there is the chance that it will +cause exceptions. + +Use a dma allocation so that we have a genuine bus address, +and read from that. +Free the allocation when done for good measure. + +Signed-off-by: Dave Stevenson + +dwc_otg: only do_split when we actually need to do a split + +The previous test would fail if the root port was in fullspeed mode +and there was a hub between the FS device and the root port. While +the transfer worked, the schedule mangling performed for high-speed +split transfers would break leading to an 8ms polling interval. + +dwc_otg: fix locking around dequeueing and killing URBs + +kill_urbs_in_qh_list() is practically only ever called with the fiq lock +already held, so don't spinlock twice in the case where we need to cancel +an isochronous transfer. + +Also fix up a case where the global interrupt register could be read with +the fiq lock not held. + +Fixes the deadlock seen in https://github.com/raspberrypi/linux/issues/2907 + +ARM64/DWC_OTG: Port dwc_otg driver to ARM64 + +In ARM64, the FIQ mechanism used by this driver is not current +implemented. As a workaround, reqular IRQ is used instead +of FIQ. + +In a separate change, the IRQ-CPU mapping is round robined +on ARM64 to increase concurrency and allow multiple interrupts +to be serviced at a time. This reduces the need for FIQ. + +Tests Run: + +This mechanism is most likely to break when multiple USB devices +are attached at the same time. So the system was tested under +stress. + +Devices: + +1. USB Speakers playing back a FLAC audio through VLC + at 96KHz.(Higher then typically, but supported on my speakers). + +2. sftp transferring large files through the buildin ethernet + connection which is connected through USB. + +3. Keyboard and mouse attached and being used. + +Although I do occasionally hear some glitches, the music seems to +play quite well. + +Signed-off-by: Michael Zoran + +usb: dwc_otg: Clean up interrupt claiming code + +The FIQ/IRQ interrupt number identification code is scattered through +the dwc_otg driver. Rationalise it, simplifying the code and solving +an existing issue. + +See: https://github.com/raspberrypi/linux/issues/2612 + +Signed-off-by: Phil Elwell + +dwc_otg: Choose appropriate IRQ handover strategy + +2711 has no MPHI peripheral, but the ARM Control block can fake +interrupts. Use the size of the DTB "mphi" reg block to determine +which is required. + +Signed-off-by: Phil Elwell + +usb: host: dwc_otg: fix compiling in separate directory + +The dwc_otg Makefile does not respect the O=path argument correctly: +include paths in CFLAGS are given relatively to object path, not source +path. Compiling in a separate directory yields #include errors. + +Signed-off-by: Marek Behún + +dwc_otg: use align_buf for small IN control transfers (#3150) + +The hardware will do a 4-byte write to memory on any IN packet received +that is between 1 and 3 bytes long. This tramples memory in the uvcvideo +driver, as it uses a sequence of 1- and 2-byte control transfers to +query the min/max/range/step of each individual camera control and +gives us buffers that are offsets into a struct. + +Catch small control transfers in the data phase and use the align_buf +to bounce the correct number of bytes into the URB's buffer. + +In general, short packets on non-control endpoints should be OK as URBs +should have enough buffer space for a wMaxPacket size transfer. + +See: https://github.com/raspberrypi/linux/issues/3148 + +Signed-off-by: Jonathan Bell + +dwc_otg: Declare DMA capability with HCD_DMA flag + +Following [1], USB controllers have to declare DMA capabilities in +order for them to be used by adding the HCD_DMA flag to their hc_driver +struct. + +[1] 7b81cb6bddd2 ("usb: add a HCD_DMA flag instead of guestimating DMA capabilities") + +Signed-off-by: Phil Elwell + +dwc_otg: checking the urb->transfer_buffer too early (#3332) + +After enable the HIGHMEM and VMSPLIT_3G, the dwc_otg driver doesn't +work well on Pi2/3 boards with 1G physical ram. Users experience +the failure when copying a file of 600M size to the USB stick. And +at the same time, the dmesg shows: +usb 1-1.1.2: reset high-speed USB device number 8 using dwc_otg +sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK +blk_update_request: I/O error, dev sda, sector 3024048 op 0x1:(WRITE) flags 0x4000 phys_seg 15 prio class 0 + +When this happens, the sg_buf sent to the driver is located in the +highmem region, the usb_sg_init() in the core/message.c will leave +transfer_buffer to NULL if the sg_buf is in highmem, but in the +dwc_otg driver, it returns -EINVAL unconditionally if transfer_buffer +is NULL. + +The driver can handle the situation of buffer to be NULL, if it is in +DMA mode, it will convert an address from transfer_dma. + +But if the conversion fails or it is in the PIO mode, we should check +buffer and return -EINVAL if it is NULL. + +BugLink: https://bugs.launchpad.net/bugs/1852510 +Signed-off-by: Hui Wang + +dwc_otg: constrain endpoint max packet and transfer size on split IN + +The hcd would unconditionally set the transfer length to the endpoint +packet size for non-isoc IN transfers. If the remaining buffer length +was less than the length of returned data, random memory would get +scribbled over, with bad effects if it crossed a page boundary. + +Force a babble error if this happens by limiting the max transfer size +to the available buffer space. DMA will stop writing to memory on a +babble condition. + +The hardware expects xfersize to be an integer multiple of maxpacket +size, so override hcchar.b.mps as well. + +Signed-off-by: Jonathan Bell + +dwc_otg: fiq_fsm: pause when cancelling split transactions + +Non-periodic splits will DMA to/from the driver-provided transfer_buffer, +which may be freed immediately after the dequeue call returns. Block until +we know the transfer is complete. + +A similar delay is needed when cleaning up disconnects, as the FIQ could +have started a periodic transfer in the previous microframe to the one +that triggered a disconnect. + +Signed-off-by: Jonathan Bell + +dwc_otg: fiq_fsm: add a barrier on entry into FIQ handler(s) + +On BCM2835, there is no hardware guarantee that multiple outstanding +reads to different peripherals will complete in-order. The FIQ code +uses peripheral reads without barriers for performance, so in the case +where a read to a slow peripheral was issued immediately prior to FIQ +entry, the first peripheral read that the FIQ did could end up with +wrong read data returned. + +Add dsb(sy) on entry so that all outstanding reads are retired. + +The FIQ only issues reads to the dwc_otg core, so per-read barriers +in the handler itself are not required. + +On BCM2836 and BCM2837 the barrier is not strictly required due to +differences in how the peripheral bus is implemented, but having +arch-specific handlers that introduce different latencies is risky. + +Signed-off-by: Jonathan Bell +--- + arch/arm/include/asm/irqflags.h | 16 +- + arch/arm/kernel/fiqasm.S | 4 + + drivers/usb/Makefile | 1 + + drivers/usb/core/generic.c | 1 + + drivers/usb/core/hub.c | 2 +- + drivers/usb/core/message.c | 79 + + drivers/usb/core/otg_productlist.h | 114 +- + drivers/usb/gadget/file_storage.c | 3676 +++++++++ + drivers/usb/host/Kconfig | 10 + + drivers/usb/host/Makefile | 1 + + drivers/usb/host/dwc_common_port/Makefile | 58 + + .../usb/host/dwc_common_port/Makefile.fbsd | 17 + + .../usb/host/dwc_common_port/Makefile.linux | 49 + + drivers/usb/host/dwc_common_port/changes.txt | 174 + + .../usb/host/dwc_common_port/doc/doxygen.cfg | 270 + + drivers/usb/host/dwc_common_port/dwc_cc.c | 532 ++ + drivers/usb/host/dwc_common_port/dwc_cc.h | 224 + + .../host/dwc_common_port/dwc_common_fbsd.c | 1308 +++ + .../host/dwc_common_port/dwc_common_linux.c | 1409 ++++ + .../host/dwc_common_port/dwc_common_nbsd.c | 1275 +++ + drivers/usb/host/dwc_common_port/dwc_crypto.c | 308 + + drivers/usb/host/dwc_common_port/dwc_crypto.h | 111 + + drivers/usb/host/dwc_common_port/dwc_dh.c | 291 + + drivers/usb/host/dwc_common_port/dwc_dh.h | 106 + + drivers/usb/host/dwc_common_port/dwc_list.h | 594 ++ + drivers/usb/host/dwc_common_port/dwc_mem.c | 245 + + drivers/usb/host/dwc_common_port/dwc_modpow.c | 636 ++ + drivers/usb/host/dwc_common_port/dwc_modpow.h | 34 + + .../usb/host/dwc_common_port/dwc_notifier.c | 319 + + .../usb/host/dwc_common_port/dwc_notifier.h | 122 + + drivers/usb/host/dwc_common_port/dwc_os.h | 1276 +++ + drivers/usb/host/dwc_common_port/usb.h | 946 +++ + drivers/usb/host/dwc_otg/Makefile | 85 + + drivers/usb/host/dwc_otg/doc/doxygen.cfg | 224 + + drivers/usb/host/dwc_otg/dummy_audio.c | 1574 ++++ + drivers/usb/host/dwc_otg/dwc_cfi_common.h | 142 + + drivers/usb/host/dwc_otg/dwc_otg_adp.c | 854 ++ + drivers/usb/host/dwc_otg/dwc_otg_adp.h | 80 + + drivers/usb/host/dwc_otg/dwc_otg_attr.c | 1212 +++ + drivers/usb/host/dwc_otg/dwc_otg_attr.h | 89 + + drivers/usb/host/dwc_otg/dwc_otg_cfi.c | 1876 +++++ + drivers/usb/host/dwc_otg/dwc_otg_cfi.h | 320 + + drivers/usb/host/dwc_otg/dwc_otg_cil.c | 7146 +++++++++++++++++ + drivers/usb/host/dwc_otg/dwc_otg_cil.h | 1464 ++++ + drivers/usb/host/dwc_otg/dwc_otg_cil_intr.c | 1601 ++++ + drivers/usb/host/dwc_otg/dwc_otg_core_if.h | 705 ++ + drivers/usb/host/dwc_otg/dwc_otg_dbg.h | 117 + + drivers/usb/host/dwc_otg/dwc_otg_driver.c | 1772 ++++ + drivers/usb/host/dwc_otg/dwc_otg_driver.h | 86 + + drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c | 1431 ++++ + drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.h | 399 + + drivers/usb/host/dwc_otg/dwc_otg_fiq_stub.S | 80 + + drivers/usb/host/dwc_otg/dwc_otg_hcd.c | 4356 ++++++++++ + drivers/usb/host/dwc_otg/dwc_otg_hcd.h | 870 ++ + drivers/usb/host/dwc_otg/dwc_otg_hcd_ddma.c | 1134 +++ + drivers/usb/host/dwc_otg/dwc_otg_hcd_if.h | 421 + + drivers/usb/host/dwc_otg/dwc_otg_hcd_intr.c | 2757 +++++++ + drivers/usb/host/dwc_otg/dwc_otg_hcd_linux.c | 1086 +++ + drivers/usb/host/dwc_otg/dwc_otg_hcd_queue.c | 970 +++ + drivers/usb/host/dwc_otg/dwc_otg_os_dep.h | 200 + + drivers/usb/host/dwc_otg/dwc_otg_pcd.c | 2725 +++++++ + drivers/usb/host/dwc_otg/dwc_otg_pcd.h | 273 + + drivers/usb/host/dwc_otg/dwc_otg_pcd_if.h | 361 + + drivers/usb/host/dwc_otg/dwc_otg_pcd_intr.c | 5148 ++++++++++++ + drivers/usb/host/dwc_otg/dwc_otg_pcd_linux.c | 1262 +++ + drivers/usb/host/dwc_otg/dwc_otg_regs.h | 2550 ++++++ + drivers/usb/host/dwc_otg/test/Makefile | 16 + + drivers/usb/host/dwc_otg/test/dwc_otg_test.pm | 337 + + .../usb/host/dwc_otg/test/test_mod_param.pl | 133 + + drivers/usb/host/dwc_otg/test/test_sysfs.pl | 193 + + 70 files changed, 60241 insertions(+), 16 deletions(-) + create mode 100644 drivers/usb/gadget/file_storage.c + create mode 100644 drivers/usb/host/dwc_common_port/Makefile + create mode 100644 drivers/usb/host/dwc_common_port/Makefile.fbsd + create mode 100644 drivers/usb/host/dwc_common_port/Makefile.linux + create mode 100644 drivers/usb/host/dwc_common_port/changes.txt + create mode 100644 drivers/usb/host/dwc_common_port/doc/doxygen.cfg + create mode 100644 drivers/usb/host/dwc_common_port/dwc_cc.c + create mode 100644 drivers/usb/host/dwc_common_port/dwc_cc.h + create mode 100644 drivers/usb/host/dwc_common_port/dwc_common_fbsd.c + create mode 100644 drivers/usb/host/dwc_common_port/dwc_common_linux.c + create mode 100644 drivers/usb/host/dwc_common_port/dwc_common_nbsd.c + create mode 100644 drivers/usb/host/dwc_common_port/dwc_crypto.c + create mode 100644 drivers/usb/host/dwc_common_port/dwc_crypto.h + create mode 100644 drivers/usb/host/dwc_common_port/dwc_dh.c + create mode 100644 drivers/usb/host/dwc_common_port/dwc_dh.h + create mode 100644 drivers/usb/host/dwc_common_port/dwc_list.h + create mode 100644 drivers/usb/host/dwc_common_port/dwc_mem.c + create mode 100644 drivers/usb/host/dwc_common_port/dwc_modpow.c + create mode 100644 drivers/usb/host/dwc_common_port/dwc_modpow.h + create mode 100644 drivers/usb/host/dwc_common_port/dwc_notifier.c + create mode 100644 drivers/usb/host/dwc_common_port/dwc_notifier.h + create mode 100644 drivers/usb/host/dwc_common_port/dwc_os.h + create mode 100644 drivers/usb/host/dwc_common_port/usb.h + create mode 100644 drivers/usb/host/dwc_otg/Makefile + create mode 100644 drivers/usb/host/dwc_otg/doc/doxygen.cfg + create mode 100644 drivers/usb/host/dwc_otg/dummy_audio.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_cfi_common.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_adp.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_adp.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_attr.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_attr.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_cfi.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_cfi.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_cil.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_cil.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_cil_intr.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_core_if.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_dbg.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_driver.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_driver.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_fiq_stub.S + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd_ddma.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd_if.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd_intr.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd_linux.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_hcd_queue.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_os_dep.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_pcd.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_pcd.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_pcd_if.h + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_pcd_intr.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_pcd_linux.c + create mode 100644 drivers/usb/host/dwc_otg/dwc_otg_regs.h + create mode 100644 drivers/usb/host/dwc_otg/test/Makefile + create mode 100644 drivers/usb/host/dwc_otg/test/dwc_otg_test.pm + create mode 100644 drivers/usb/host/dwc_otg/test/test_mod_param.pl + create mode 100644 drivers/usb/host/dwc_otg/test/test_sysfs.pl + +--- a/arch/arm/include/asm/irqflags.h ++++ b/arch/arm/include/asm/irqflags.h +@@ -163,13 +163,23 @@ static inline unsigned long arch_local_s + } + + /* +- * restore saved IRQ & FIQ state ++ * restore saved IRQ state + */ + #define arch_local_irq_restore arch_local_irq_restore + static inline void arch_local_irq_restore(unsigned long flags) + { +- asm volatile( +- " msr " IRQMASK_REG_NAME_W ", %0 @ local_irq_restore" ++ unsigned long temp = 0; ++ flags &= ~(1 << 6); ++ asm volatile ( ++ " mrs %0, cpsr" ++ : "=r" (temp) ++ : ++ : "memory", "cc"); ++ /* Preserve FIQ bit */ ++ temp &= (1 << 6); ++ flags = flags | temp; ++ asm volatile ( ++ " msr cpsr_c, %0 @ local_irq_restore" + : + : "r" (flags) + : "memory", "cc"); +--- a/arch/arm/kernel/fiqasm.S ++++ b/arch/arm/kernel/fiqasm.S +@@ -47,3 +47,7 @@ ENTRY(__get_fiq_regs) + mov r0, r0 @ avoid hazard prior to ARMv4 + ret lr + ENDPROC(__get_fiq_regs) ++ ++ENTRY(__FIQ_Branch) ++ mov pc, r8 ++ENDPROC(__FIQ_Branch) +--- a/drivers/usb/Makefile ++++ b/drivers/usb/Makefile +@@ -9,6 +9,7 @@ obj-$(CONFIG_USB_COMMON) += common/ + obj-$(CONFIG_USB) += core/ + obj-$(CONFIG_USB_SUPPORT) += phy/ + ++obj-$(CONFIG_USB_DWCOTG) += host/ + obj-$(CONFIG_USB_DWC3) += dwc3/ + obj-$(CONFIG_USB_DWC2) += dwc2/ + obj-$(CONFIG_USB_ISP1760) += isp1760/ +--- a/drivers/usb/core/generic.c ++++ b/drivers/usb/core/generic.c +@@ -190,6 +190,7 @@ int usb_choose_configuration(struct usb_ + dev_warn(&udev->dev, + "no configuration chosen from %d choice%s\n", + num_configs, plural(num_configs)); ++ dev_warn(&udev->dev, "No support over %dmA\n", udev->bus_mA); + } + return i; + } +--- a/drivers/usb/core/hub.c ++++ b/drivers/usb/core/hub.c +@@ -5494,7 +5494,7 @@ static void port_event(struct usb_hub *h + port_dev->over_current_count++; + port_over_current_notify(port_dev); + +- dev_dbg(&port_dev->dev, "over-current change #%u\n", ++ dev_notice(&port_dev->dev, "over-current change #%u\n", + port_dev->over_current_count); + usb_clear_port_feature(hdev, port1, + USB_PORT_FEAT_C_OVER_CURRENT); +--- a/drivers/usb/core/message.c ++++ b/drivers/usb/core/message.c +@@ -2129,6 +2129,85 @@ free_interfaces: + if (cp->string == NULL && + !(dev->quirks & USB_QUIRK_CONFIG_INTF_STRINGS)) + cp->string = usb_cache_string(dev, cp->desc.iConfiguration); ++/* Uncomment this define to enable the HS Electrical Test support */ ++#define DWC_HS_ELECT_TST 1 ++#ifdef DWC_HS_ELECT_TST ++ /* Here we implement the HS Electrical Test support. The ++ * tester uses a vendor ID of 0x1A0A to indicate we should ++ * run a special test sequence. The product ID tells us ++ * which sequence to run. We invoke the test sequence by ++ * sending a non-standard SetFeature command to our root ++ * hub port. Our dwc_otg_hcd_hub_control() routine will ++ * recognize the command and perform the desired test ++ * sequence. ++ */ ++ if (dev->descriptor.idVendor == 0x1A0A) { ++ /* HSOTG Electrical Test */ ++ dev_warn(&dev->dev, "VID from HSOTG Electrical Test Fixture\n"); ++ ++ if (dev->bus && dev->bus->root_hub) { ++ struct usb_device *hdev = dev->bus->root_hub; ++ dev_warn(&dev->dev, "Got PID 0x%x\n", dev->descriptor.idProduct); ++ ++ switch (dev->descriptor.idProduct) { ++ case 0x0101: /* TEST_SE0_NAK */ ++ dev_warn(&dev->dev, "TEST_SE0_NAK\n"); ++ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), ++ USB_REQ_SET_FEATURE, USB_RT_PORT, ++ USB_PORT_FEAT_TEST, 0x300, NULL, 0, HZ); ++ break; ++ ++ case 0x0102: /* TEST_J */ ++ dev_warn(&dev->dev, "TEST_J\n"); ++ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), ++ USB_REQ_SET_FEATURE, USB_RT_PORT, ++ USB_PORT_FEAT_TEST, 0x100, NULL, 0, HZ); ++ break; ++ ++ case 0x0103: /* TEST_K */ ++ dev_warn(&dev->dev, "TEST_K\n"); ++ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), ++ USB_REQ_SET_FEATURE, USB_RT_PORT, ++ USB_PORT_FEAT_TEST, 0x200, NULL, 0, HZ); ++ break; ++ ++ case 0x0104: /* TEST_PACKET */ ++ dev_warn(&dev->dev, "TEST_PACKET\n"); ++ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), ++ USB_REQ_SET_FEATURE, USB_RT_PORT, ++ USB_PORT_FEAT_TEST, 0x400, NULL, 0, HZ); ++ break; ++ ++ case 0x0105: /* TEST_FORCE_ENABLE */ ++ dev_warn(&dev->dev, "TEST_FORCE_ENABLE\n"); ++ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), ++ USB_REQ_SET_FEATURE, USB_RT_PORT, ++ USB_PORT_FEAT_TEST, 0x500, NULL, 0, HZ); ++ break; ++ ++ case 0x0106: /* HS_HOST_PORT_SUSPEND_RESUME */ ++ dev_warn(&dev->dev, "HS_HOST_PORT_SUSPEND_RESUME\n"); ++ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), ++ USB_REQ_SET_FEATURE, USB_RT_PORT, ++ USB_PORT_FEAT_TEST, 0x600, NULL, 0, 40 * HZ); ++ break; ++ ++ case 0x0107: /* SINGLE_STEP_GET_DEVICE_DESCRIPTOR setup */ ++ dev_warn(&dev->dev, "SINGLE_STEP_GET_DEVICE_DESCRIPTOR setup\n"); ++ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), ++ USB_REQ_SET_FEATURE, USB_RT_PORT, ++ USB_PORT_FEAT_TEST, 0x700, NULL, 0, 40 * HZ); ++ break; ++ ++ case 0x0108: /* SINGLE_STEP_GET_DEVICE_DESCRIPTOR execute */ ++ dev_warn(&dev->dev, "SINGLE_STEP_GET_DEVICE_DESCRIPTOR execute\n"); ++ usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0), ++ USB_REQ_SET_FEATURE, USB_RT_PORT, ++ USB_PORT_FEAT_TEST, 0x800, NULL, 0, 40 * HZ); ++ } ++ } ++ } ++#endif /* DWC_HS_ELECT_TST */ + + /* Now that the interfaces are installed, re-enable LPM. */ + usb_unlocked_enable_lpm(dev); +--- a/drivers/usb/core/otg_productlist.h ++++ b/drivers/usb/core/otg_productlist.h +@@ -11,33 +11,82 @@ + static struct usb_device_id productlist_table[] = { + + /* hubs are optional in OTG, but very handy ... */ ++#define CERT_WITHOUT_HUBS ++#if defined(CERT_WITHOUT_HUBS) ++{ USB_DEVICE( 0x0000, 0x0000 ), }, /* Root HUB Only*/ ++#else + { USB_DEVICE_INFO(USB_CLASS_HUB, 0, 0), }, + { USB_DEVICE_INFO(USB_CLASS_HUB, 0, 1), }, ++{ USB_DEVICE_INFO(USB_CLASS_HUB, 0, 2), }, ++#endif + + #ifdef CONFIG_USB_PRINTER /* ignoring nonstatic linkage! */ + /* FIXME actually, printers are NOT supposed to use device classes; + * they're supposed to use interface classes... + */ +-{ USB_DEVICE_INFO(7, 1, 1) }, +-{ USB_DEVICE_INFO(7, 1, 2) }, +-{ USB_DEVICE_INFO(7, 1, 3) }, ++//{ USB_DEVICE_INFO(7, 1, 1) }, ++//{ USB_DEVICE_INFO(7, 1, 2) }, ++//{ USB_DEVICE_INFO(7, 1, 3) }, + #endif + + #ifdef CONFIG_USB_NET_CDCETHER + /* Linux-USB CDC Ethernet gadget */ +-{ USB_DEVICE(0x0525, 0xa4a1), }, ++//{ USB_DEVICE(0x0525, 0xa4a1), }, + /* Linux-USB CDC Ethernet + RNDIS gadget */ +-{ USB_DEVICE(0x0525, 0xa4a2), }, ++//{ USB_DEVICE(0x0525, 0xa4a2), }, + #endif + + #if IS_ENABLED(CONFIG_USB_TEST) + /* gadget zero, for testing */ +-{ USB_DEVICE(0x0525, 0xa4a0), }, ++//{ USB_DEVICE(0x0525, 0xa4a0), }, + #endif + ++/* OPT Tester */ ++{ USB_DEVICE( 0x1a0a, 0x0101 ), }, /* TEST_SE0_NAK */ ++{ USB_DEVICE( 0x1a0a, 0x0102 ), }, /* Test_J */ ++{ USB_DEVICE( 0x1a0a, 0x0103 ), }, /* Test_K */ ++{ USB_DEVICE( 0x1a0a, 0x0104 ), }, /* Test_PACKET */ ++{ USB_DEVICE( 0x1a0a, 0x0105 ), }, /* Test_FORCE_ENABLE */ ++{ USB_DEVICE( 0x1a0a, 0x0106 ), }, /* HS_PORT_SUSPEND_RESUME */ ++{ USB_DEVICE( 0x1a0a, 0x0107 ), }, /* SINGLE_STEP_GET_DESCRIPTOR setup */ ++{ USB_DEVICE( 0x1a0a, 0x0108 ), }, /* SINGLE_STEP_GET_DESCRIPTOR execute */ ++ ++/* Sony cameras */ ++{ USB_DEVICE_VER(0x054c,0x0010,0x0410, 0x0500), }, ++ ++/* Memory Devices */ ++//{ USB_DEVICE( 0x0781, 0x5150 ), }, /* SanDisk */ ++//{ USB_DEVICE( 0x05DC, 0x0080 ), }, /* Lexar */ ++//{ USB_DEVICE( 0x4146, 0x9281 ), }, /* IOMEGA */ ++//{ USB_DEVICE( 0x067b, 0x2507 ), }, /* Hammer 20GB External HD */ ++{ USB_DEVICE( 0x0EA0, 0x2168 ), }, /* Ours Technology Inc. (BUFFALO ClipDrive)*/ ++//{ USB_DEVICE( 0x0457, 0x0150 ), }, /* Silicon Integrated Systems Corp. */ ++ ++/* HP Printers */ ++//{ USB_DEVICE( 0x03F0, 0x1102 ), }, /* HP Photosmart 245 */ ++//{ USB_DEVICE( 0x03F0, 0x1302 ), }, /* HP Photosmart 370 Series */ ++ ++/* Speakers */ ++//{ USB_DEVICE( 0x0499, 0x3002 ), }, /* YAMAHA YST-MS35D USB Speakers */ ++//{ USB_DEVICE( 0x0672, 0x1041 ), }, /* Labtec USB Headset */ ++ + { } /* Terminating entry */ + }; + ++static inline void report_errors(struct usb_device *dev) ++{ ++ /* OTG MESSAGE: report errors here, customize to match your product */ ++ dev_info(&dev->dev, "device Vendor:%04x Product:%04x is not supported\n", ++ le16_to_cpu(dev->descriptor.idVendor), ++ le16_to_cpu(dev->descriptor.idProduct)); ++ if (USB_CLASS_HUB == dev->descriptor.bDeviceClass){ ++ dev_printk(KERN_CRIT, &dev->dev, "Unsupported Hub Topology\n"); ++ } else { ++ dev_printk(KERN_CRIT, &dev->dev, "Attached Device is not Supported\n"); ++ } ++} ++ ++ + static int is_targeted(struct usb_device *dev) + { + struct usb_device_id *id = productlist_table; +@@ -87,16 +136,57 @@ static int is_targeted(struct usb_device + continue; + + return 1; +- } ++ /* NOTE: can't use usb_match_id() since interface caches ++ * aren't set up yet. this is cut/paste from that code. ++ */ ++ for (id = whitelist_table; id->match_flags; id++) { ++#ifdef DEBUG ++ dev_dbg(&dev->dev, ++ "ID: V:%04x P:%04x DC:%04x SC:%04x PR:%04x \n", ++ id->idVendor, ++ id->idProduct, ++ id->bDeviceClass, ++ id->bDeviceSubClass, ++ id->bDeviceProtocol); ++#endif + +- /* add other match criteria here ... */ ++ if ((id->match_flags & USB_DEVICE_ID_MATCH_VENDOR) && ++ id->idVendor != le16_to_cpu(dev->descriptor.idVendor)) ++ continue; ++ ++ if ((id->match_flags & USB_DEVICE_ID_MATCH_PRODUCT) && ++ id->idProduct != le16_to_cpu(dev->descriptor.idProduct)) ++ continue; ++ ++ /* No need to test id->bcdDevice_lo != 0, since 0 is never ++ greater than any unsigned number. */ ++ if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_LO) && ++ (id->bcdDevice_lo > le16_to_cpu(dev->descriptor.bcdDevice))) ++ continue; ++ ++ if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_HI) && ++ (id->bcdDevice_hi < le16_to_cpu(dev->descriptor.bcdDevice))) ++ continue; ++ ++ if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_CLASS) && ++ (id->bDeviceClass != dev->descriptor.bDeviceClass)) ++ continue; ++ ++ if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_SUBCLASS) && ++ (id->bDeviceSubClass != dev->descriptor.bDeviceSubClass)) ++ continue; ++ ++ if ((id->match_flags & USB_DEVICE_ID_MATCH_DEV_PROTOCOL) && ++ (id->bDeviceProtocol != dev->descriptor.bDeviceProtocol)) ++ continue; + ++ return 1; ++ } ++ } + +- /* OTG MESSAGE: report errors here, customize to match your product */ +- dev_err(&dev->dev, "device v%04x p%04x is not supported\n", +- le16_to_cpu(dev->descriptor.idVendor), +- le16_to_cpu(dev->descriptor.idProduct)); ++ /* add other match criteria here ... */ + ++ report_errors(dev); + return 0; + } + +--- /dev/null ++++ b/drivers/usb/gadget/file_storage.c +@@ -0,0 +1,3676 @@ ++/* ++ * file_storage.c -- File-backed USB Storage Gadget, for USB development ++ * ++ * Copyright (C) 2003-2008 Alan Stern ++ * All rights reserved. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions ++ * are met: ++ * 1. Redistributions of source code must retain the above copyright ++ * notice, this list of conditions, and the following disclaimer, ++ * without modification. ++ * 2. Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in the ++ * documentation and/or other materials provided with the distribution. ++ * 3. The names of the above-listed copyright holders may not be used ++ * to endorse or promote products derived from this software without ++ * specific prior written permission. ++ * ++ * ALTERNATIVELY, this software may be distributed under the terms of the ++ * GNU General Public License ("GPL") as published by the Free Software ++ * Foundation, either version 2 of that License or (at your option) any ++ * later version. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS ++ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ++ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR ++ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR ++ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF ++ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING ++ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ */ ++ ++ ++/* ++ * The File-backed Storage Gadget acts as a USB Mass Storage device, ++ * appearing to the host as a disk drive or as a CD-ROM drive. In addition ++ * to providing an example of a genuinely useful gadget driver for a USB ++ * device, it also illustrates a technique of double-buffering for increased ++ * throughput. Last but not least, it gives an easy way to probe the ++ * behavior of the Mass Storage drivers in a USB host. ++ * ++ * Backing storage is provided by a regular file or a block device, specified ++ * by the "file" module parameter. Access can be limited to read-only by ++ * setting the optional "ro" module parameter. (For CD-ROM emulation, ++ * access is always read-only.) The gadget will indicate that it has ++ * removable media if the optional "removable" module parameter is set. ++ * ++ * The gadget supports the Control-Bulk (CB), Control-Bulk-Interrupt (CBI), ++ * and Bulk-Only (also known as Bulk-Bulk-Bulk or BBB) transports, selected ++ * by the optional "transport" module parameter. It also supports the ++ * following protocols: RBC (0x01), ATAPI or SFF-8020i (0x02), QIC-157 (0c03), ++ * UFI (0x04), SFF-8070i (0x05), and transparent SCSI (0x06), selected by ++ * the optional "protocol" module parameter. In addition, the default ++ * Vendor ID, Product ID, release number and serial number can be overridden. ++ * ++ * There is support for multiple logical units (LUNs), each of which has ++ * its own backing file. The number of LUNs can be set using the optional ++ * "luns" module parameter (anywhere from 1 to 8), and the corresponding ++ * files are specified using comma-separated lists for "file" and "ro". ++ * The default number of LUNs is taken from the number of "file" elements; ++ * it is 1 if "file" is not given. If "removable" is not set then a backing ++ * file must be specified for each LUN. If it is set, then an unspecified ++ * or empty backing filename means the LUN's medium is not loaded. Ideally ++ * each LUN would be settable independently as a disk drive or a CD-ROM ++ * drive, but currently all LUNs have to be the same type. The CD-ROM ++ * emulation includes a single data track and no audio tracks; hence there ++ * need be only one backing file per LUN. ++ * ++ * Requirements are modest; only a bulk-in and a bulk-out endpoint are ++ * needed (an interrupt-out endpoint is also needed for CBI). The memory ++ * requirement amounts to two 16K buffers, size configurable by a parameter. ++ * Support is included for both full-speed and high-speed operation. ++ * ++ * Note that the driver is slightly non-portable in that it assumes a ++ * single memory/DMA buffer will be useable for bulk-in, bulk-out, and ++ * interrupt-in endpoints. With most device controllers this isn't an ++ * issue, but there may be some with hardware restrictions that prevent ++ * a buffer from being used by more than one endpoint. ++ * ++ * Module options: ++ * ++ * file=filename[,filename...] ++ * Required if "removable" is not set, names of ++ * the files or block devices used for ++ * backing storage ++ * serial=HHHH... Required serial number (string of hex chars) ++ * ro=b[,b...] Default false, booleans for read-only access ++ * removable Default false, boolean for removable media ++ * luns=N Default N = number of filenames, number of ++ * LUNs to support ++ * nofua=b[,b...] Default false, booleans for ignore FUA flag ++ * in SCSI WRITE(10,12) commands ++ * stall Default determined according to the type of ++ * USB device controller (usually true), ++ * boolean to permit the driver to halt ++ * bulk endpoints ++ * cdrom Default false, boolean for whether to emulate ++ * a CD-ROM drive ++ * transport=XXX Default BBB, transport name (CB, CBI, or BBB) ++ * protocol=YYY Default SCSI, protocol name (RBC, 8020 or ++ * ATAPI, QIC, UFI, 8070, or SCSI; ++ * also 1 - 6) ++ * vendor=0xVVVV Default 0x0525 (NetChip), USB Vendor ID ++ * product=0xPPPP Default 0xa4a5 (FSG), USB Product ID ++ * release=0xRRRR Override the USB release number (bcdDevice) ++ * buflen=N Default N=16384, buffer size used (will be ++ * rounded down to a multiple of ++ * PAGE_CACHE_SIZE) ++ * ++ * If CONFIG_USB_FILE_STORAGE_TEST is not set, only the "file", "serial", "ro", ++ * "removable", "luns", "nofua", "stall", and "cdrom" options are available; ++ * default values are used for everything else. ++ * ++ * The pathnames of the backing files and the ro settings are available in ++ * the attribute files "file", "nofua", and "ro" in the lun subdirectory of ++ * the gadget's sysfs directory. If the "removable" option is set, writing to ++ * these files will simulate ejecting/loading the medium (writing an empty ++ * line means eject) and adjusting a write-enable tab. Changes to the ro ++ * setting are not allowed when the medium is loaded or if CD-ROM emulation ++ * is being used. ++ * ++ * This gadget driver is heavily based on "Gadget Zero" by David Brownell. ++ * The driver's SCSI command interface was based on the "Information ++ * technology - Small Computer System Interface - 2" document from ++ * X3T9.2 Project 375D, Revision 10L, 7-SEP-93, available at ++ * . The single exception ++ * is opcode 0x23 (READ FORMAT CAPACITIES), which was based on the ++ * "Universal Serial Bus Mass Storage Class UFI Command Specification" ++ * document, Revision 1.0, December 14, 1998, available at ++ * . ++ */ ++ ++ ++/* ++ * Driver Design ++ * ++ * The FSG driver is fairly straightforward. There is a main kernel ++ * thread that handles most of the work. Interrupt routines field ++ * callbacks from the controller driver: bulk- and interrupt-request ++ * completion notifications, endpoint-0 events, and disconnect events. ++ * Completion events are passed to the main thread by wakeup calls. Many ++ * ep0 requests are handled at interrupt time, but SetInterface, ++ * SetConfiguration, and device reset requests are forwarded to the ++ * thread in the form of "exceptions" using SIGUSR1 signals (since they ++ * should interrupt any ongoing file I/O operations). ++ * ++ * The thread's main routine implements the standard command/data/status ++ * parts of a SCSI interaction. It and its subroutines are full of tests ++ * for pending signals/exceptions -- all this polling is necessary since ++ * the kernel has no setjmp/longjmp equivalents. (Maybe this is an ++ * indication that the driver really wants to be running in userspace.) ++ * An important point is that so long as the thread is alive it keeps an ++ * open reference to the backing file. This will prevent unmounting ++ * the backing file's underlying filesystem and could cause problems ++ * during system shutdown, for example. To prevent such problems, the ++ * thread catches INT, TERM, and KILL signals and converts them into ++ * an EXIT exception. ++ * ++ * In normal operation the main thread is started during the gadget's ++ * fsg_bind() callback and stopped during fsg_unbind(). But it can also ++ * exit when it receives a signal, and there's no point leaving the ++ * gadget running when the thread is dead. So just before the thread ++ * exits, it deregisters the gadget driver. This makes things a little ++ * tricky: The driver is deregistered at two places, and the exiting ++ * thread can indirectly call fsg_unbind() which in turn can tell the ++ * thread to exit. The first problem is resolved through the use of the ++ * REGISTERED atomic bitflag; the driver will only be deregistered once. ++ * The second problem is resolved by having fsg_unbind() check ++ * fsg->state; it won't try to stop the thread if the state is already ++ * FSG_STATE_TERMINATED. ++ * ++ * To provide maximum throughput, the driver uses a circular pipeline of ++ * buffer heads (struct fsg_buffhd). In principle the pipeline can be ++ * arbitrarily long; in practice the benefits don't justify having more ++ * than 2 stages (i.e., double buffering). But it helps to think of the ++ * pipeline as being a long one. Each buffer head contains a bulk-in and ++ * a bulk-out request pointer (since the buffer can be used for both ++ * output and input -- directions always are given from the host's ++ * point of view) as well as a pointer to the buffer and various state ++ * variables. ++ * ++ * Use of the pipeline follows a simple protocol. There is a variable ++ * (fsg->next_buffhd_to_fill) that points to the next buffer head to use. ++ * At any time that buffer head may still be in use from an earlier ++ * request, so each buffer head has a state variable indicating whether ++ * it is EMPTY, FULL, or BUSY. Typical use involves waiting for the ++ * buffer head to be EMPTY, filling the buffer either by file I/O or by ++ * USB I/O (during which the buffer head is BUSY), and marking the buffer ++ * head FULL when the I/O is complete. Then the buffer will be emptied ++ * (again possibly by USB I/O, during which it is marked BUSY) and ++ * finally marked EMPTY again (possibly by a completion routine). ++ * ++ * A module parameter tells the driver to avoid stalling the bulk ++ * endpoints wherever the transport specification allows. This is ++ * necessary for some UDCs like the SuperH, which cannot reliably clear a ++ * halt on a bulk endpoint. However, under certain circumstances the ++ * Bulk-only specification requires a stall. In such cases the driver ++ * will halt the endpoint and set a flag indicating that it should clear ++ * the halt in software during the next device reset. Hopefully this ++ * will permit everything to work correctly. Furthermore, although the ++ * specification allows the bulk-out endpoint to halt when the host sends ++ * too much data, implementing this would cause an unavoidable race. ++ * The driver will always use the "no-stall" approach for OUT transfers. ++ * ++ * One subtle point concerns sending status-stage responses for ep0 ++ * requests. Some of these requests, such as device reset, can involve ++ * interrupting an ongoing file I/O operation, which might take an ++ * arbitrarily long time. During that delay the host might give up on ++ * the original ep0 request and issue a new one. When that happens the ++ * driver should not notify the host about completion of the original ++ * request, as the host will no longer be waiting for it. So the driver ++ * assigns to each ep0 request a unique tag, and it keeps track of the ++ * tag value of the request associated with a long-running exception ++ * (device-reset, interface-change, or configuration-change). When the ++ * exception handler is finished, the status-stage response is submitted ++ * only if the current ep0 request tag is equal to the exception request ++ * tag. Thus only the most recently received ep0 request will get a ++ * status-stage response. ++ * ++ * Warning: This driver source file is too long. It ought to be split up ++ * into a header file plus about 3 separate .c files, to handle the details ++ * of the Gadget, USB Mass Storage, and SCSI protocols. ++ */ ++ ++ ++/* #define VERBOSE_DEBUG */ ++/* #define DUMP_MSGS */ ++ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++ ++#include "gadget_chips.h" ++ ++ ++ ++/* ++ * Kbuild is not very cooperative with respect to linking separately ++ * compiled library objects into one module. So for now we won't use ++ * separate compilation ... ensuring init/exit sections work to shrink ++ * the runtime footprint, and giving us at least some parts of what ++ * a "gcc --combine ... part1.c part2.c part3.c ... " build would. ++ */ ++#include "usbstring.c" ++#include "config.c" ++#include "epautoconf.c" ++ ++/*-------------------------------------------------------------------------*/ ++ ++#define DRIVER_DESC "File-backed Storage Gadget" ++#define DRIVER_NAME "g_file_storage" ++#define DRIVER_VERSION "1 September 2010" ++ ++static char fsg_string_manufacturer[64]; ++static const char fsg_string_product[] = DRIVER_DESC; ++static const char fsg_string_config[] = "Self-powered"; ++static const char fsg_string_interface[] = "Mass Storage"; ++ ++ ++#include "storage_common.c" ++ ++ ++MODULE_DESCRIPTION(DRIVER_DESC); ++MODULE_AUTHOR("Alan Stern"); ++MODULE_LICENSE("Dual BSD/GPL"); ++ ++/* ++ * This driver assumes self-powered hardware and has no way for users to ++ * trigger remote wakeup. It uses autoconfiguration to select endpoints ++ * and endpoint addresses. ++ */ ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++ ++/* Encapsulate the module parameter settings */ ++ ++static struct { ++ char *file[FSG_MAX_LUNS]; ++ char *serial; ++ bool ro[FSG_MAX_LUNS]; ++ bool nofua[FSG_MAX_LUNS]; ++ unsigned int num_filenames; ++ unsigned int num_ros; ++ unsigned int num_nofuas; ++ unsigned int nluns; ++ ++ bool removable; ++ bool can_stall; ++ bool cdrom; ++ ++ char *transport_parm; ++ char *protocol_parm; ++ unsigned short vendor; ++ unsigned short product; ++ unsigned short release; ++ unsigned int buflen; ++ ++ int transport_type; ++ char *transport_name; ++ int protocol_type; ++ char *protocol_name; ++ ++} mod_data = { // Default values ++ .transport_parm = "BBB", ++ .protocol_parm = "SCSI", ++ .removable = 0, ++ .can_stall = 1, ++ .cdrom = 0, ++ .vendor = FSG_VENDOR_ID, ++ .product = FSG_PRODUCT_ID, ++ .release = 0xffff, // Use controller chip type ++ .buflen = 16384, ++ }; ++ ++ ++module_param_array_named(file, mod_data.file, charp, &mod_data.num_filenames, ++ S_IRUGO); ++MODULE_PARM_DESC(file, "names of backing files or devices"); ++ ++module_param_named(serial, mod_data.serial, charp, S_IRUGO); ++MODULE_PARM_DESC(serial, "USB serial number"); ++ ++module_param_array_named(ro, mod_data.ro, bool, &mod_data.num_ros, S_IRUGO); ++MODULE_PARM_DESC(ro, "true to force read-only"); ++ ++module_param_array_named(nofua, mod_data.nofua, bool, &mod_data.num_nofuas, ++ S_IRUGO); ++MODULE_PARM_DESC(nofua, "true to ignore SCSI WRITE(10,12) FUA bit"); ++ ++module_param_named(luns, mod_data.nluns, uint, S_IRUGO); ++MODULE_PARM_DESC(luns, "number of LUNs"); ++ ++module_param_named(removable, mod_data.removable, bool, S_IRUGO); ++MODULE_PARM_DESC(removable, "true to simulate removable media"); ++ ++module_param_named(stall, mod_data.can_stall, bool, S_IRUGO); ++MODULE_PARM_DESC(stall, "false to prevent bulk stalls"); ++ ++module_param_named(cdrom, mod_data.cdrom, bool, S_IRUGO); ++MODULE_PARM_DESC(cdrom, "true to emulate cdrom instead of disk"); ++ ++/* In the non-TEST version, only the module parameters listed above ++ * are available. */ ++#ifdef CONFIG_USB_FILE_STORAGE_TEST ++ ++module_param_named(transport, mod_data.transport_parm, charp, S_IRUGO); ++MODULE_PARM_DESC(transport, "type of transport (BBB, CBI, or CB)"); ++ ++module_param_named(protocol, mod_data.protocol_parm, charp, S_IRUGO); ++MODULE_PARM_DESC(protocol, "type of protocol (RBC, 8020, QIC, UFI, " ++ "8070, or SCSI)"); ++ ++module_param_named(vendor, mod_data.vendor, ushort, S_IRUGO); ++MODULE_PARM_DESC(vendor, "USB Vendor ID"); ++ ++module_param_named(product, mod_data.product, ushort, S_IRUGO); ++MODULE_PARM_DESC(product, "USB Product ID"); ++ ++module_param_named(release, mod_data.release, ushort, S_IRUGO); ++MODULE_PARM_DESC(release, "USB release number"); ++ ++module_param_named(buflen, mod_data.buflen, uint, S_IRUGO); ++MODULE_PARM_DESC(buflen, "I/O buffer size"); ++ ++#endif /* CONFIG_USB_FILE_STORAGE_TEST */ ++ ++ ++/* ++ * These definitions will permit the compiler to avoid generating code for ++ * parts of the driver that aren't used in the non-TEST version. Even gcc ++ * can recognize when a test of a constant expression yields a dead code ++ * path. ++ */ ++ ++#ifdef CONFIG_USB_FILE_STORAGE_TEST ++ ++#define transport_is_bbb() (mod_data.transport_type == USB_PR_BULK) ++#define transport_is_cbi() (mod_data.transport_type == USB_PR_CBI) ++#define protocol_is_scsi() (mod_data.protocol_type == USB_SC_SCSI) ++ ++#else ++ ++#define transport_is_bbb() 1 ++#define transport_is_cbi() 0 ++#define protocol_is_scsi() 1 ++ ++#endif /* CONFIG_USB_FILE_STORAGE_TEST */ ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++ ++struct fsg_dev { ++ /* lock protects: state, all the req_busy's, and cbbuf_cmnd */ ++ spinlock_t lock; ++ struct usb_gadget *gadget; ++ ++ /* filesem protects: backing files in use */ ++ struct rw_semaphore filesem; ++ ++ /* reference counting: wait until all LUNs are released */ ++ struct kref ref; ++ ++ struct usb_ep *ep0; // Handy copy of gadget->ep0 ++ struct usb_request *ep0req; // For control responses ++ unsigned int ep0_req_tag; ++ const char *ep0req_name; ++ ++ struct usb_request *intreq; // For interrupt responses ++ int intreq_busy; ++ struct fsg_buffhd *intr_buffhd; ++ ++ unsigned int bulk_out_maxpacket; ++ enum fsg_state state; // For exception handling ++ unsigned int exception_req_tag; ++ ++ u8 config, new_config; ++ ++ unsigned int running : 1; ++ unsigned int bulk_in_enabled : 1; ++ unsigned int bulk_out_enabled : 1; ++ unsigned int intr_in_enabled : 1; ++ unsigned int phase_error : 1; ++ unsigned int short_packet_received : 1; ++ unsigned int bad_lun_okay : 1; ++ ++ unsigned long atomic_bitflags; ++#define REGISTERED 0 ++#define IGNORE_BULK_OUT 1 ++#define SUSPENDED 2 ++ ++ struct usb_ep *bulk_in; ++ struct usb_ep *bulk_out; ++ struct usb_ep *intr_in; ++ ++ struct fsg_buffhd *next_buffhd_to_fill; ++ struct fsg_buffhd *next_buffhd_to_drain; ++ ++ int thread_wakeup_needed; ++ struct completion thread_notifier; ++ struct task_struct *thread_task; ++ ++ int cmnd_size; ++ u8 cmnd[MAX_COMMAND_SIZE]; ++ enum data_direction data_dir; ++ u32 data_size; ++ u32 data_size_from_cmnd; ++ u32 tag; ++ unsigned int lun; ++ u32 residue; ++ u32 usb_amount_left; ++ ++ /* The CB protocol offers no way for a host to know when a command ++ * has completed. As a result the next command may arrive early, ++ * and we will still have to handle it. For that reason we need ++ * a buffer to store new commands when using CB (or CBI, which ++ * does not oblige a host to wait for command completion either). */ ++ int cbbuf_cmnd_size; ++ u8 cbbuf_cmnd[MAX_COMMAND_SIZE]; ++ ++ unsigned int nluns; ++ struct fsg_lun *luns; ++ struct fsg_lun *curlun; ++ /* Must be the last entry */ ++ struct fsg_buffhd buffhds[]; ++}; ++ ++typedef void (*fsg_routine_t)(struct fsg_dev *); ++ ++static int exception_in_progress(struct fsg_dev *fsg) ++{ ++ return (fsg->state > FSG_STATE_IDLE); ++} ++ ++/* Make bulk-out requests be divisible by the maxpacket size */ ++static void set_bulk_out_req_length(struct fsg_dev *fsg, ++ struct fsg_buffhd *bh, unsigned int length) ++{ ++ unsigned int rem; ++ ++ bh->bulk_out_intended_length = length; ++ rem = length % fsg->bulk_out_maxpacket; ++ if (rem > 0) ++ length += fsg->bulk_out_maxpacket - rem; ++ bh->outreq->length = length; ++} ++ ++static struct fsg_dev *the_fsg; ++static struct usb_gadget_driver fsg_driver; ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static int fsg_set_halt(struct fsg_dev *fsg, struct usb_ep *ep) ++{ ++ const char *name; ++ ++ if (ep == fsg->bulk_in) ++ name = "bulk-in"; ++ else if (ep == fsg->bulk_out) ++ name = "bulk-out"; ++ else ++ name = ep->name; ++ DBG(fsg, "%s set halt\n", name); ++ return usb_ep_set_halt(ep); ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* ++ * DESCRIPTORS ... most are static, but strings and (full) configuration ++ * descriptors are built on demand. Also the (static) config and interface ++ * descriptors are adjusted during fsg_bind(). ++ */ ++ ++/* There is only one configuration. */ ++#define CONFIG_VALUE 1 ++ ++static struct usb_device_descriptor ++device_desc = { ++ .bLength = sizeof device_desc, ++ .bDescriptorType = USB_DT_DEVICE, ++ ++ .bcdUSB = cpu_to_le16(0x0200), ++ .bDeviceClass = USB_CLASS_PER_INTERFACE, ++ ++ /* The next three values can be overridden by module parameters */ ++ .idVendor = cpu_to_le16(FSG_VENDOR_ID), ++ .idProduct = cpu_to_le16(FSG_PRODUCT_ID), ++ .bcdDevice = cpu_to_le16(0xffff), ++ ++ .iManufacturer = FSG_STRING_MANUFACTURER, ++ .iProduct = FSG_STRING_PRODUCT, ++ .iSerialNumber = FSG_STRING_SERIAL, ++ .bNumConfigurations = 1, ++}; ++ ++static struct usb_config_descriptor ++config_desc = { ++ .bLength = sizeof config_desc, ++ .bDescriptorType = USB_DT_CONFIG, ++ ++ /* wTotalLength computed by usb_gadget_config_buf() */ ++ .bNumInterfaces = 1, ++ .bConfigurationValue = CONFIG_VALUE, ++ .iConfiguration = FSG_STRING_CONFIG, ++ .bmAttributes = USB_CONFIG_ATT_ONE | USB_CONFIG_ATT_SELFPOWER, ++ .bMaxPower = CONFIG_USB_GADGET_VBUS_DRAW / 2, ++}; ++ ++ ++static struct usb_qualifier_descriptor ++dev_qualifier = { ++ .bLength = sizeof dev_qualifier, ++ .bDescriptorType = USB_DT_DEVICE_QUALIFIER, ++ ++ .bcdUSB = cpu_to_le16(0x0200), ++ .bDeviceClass = USB_CLASS_PER_INTERFACE, ++ ++ .bNumConfigurations = 1, ++}; ++ ++static int populate_bos(struct fsg_dev *fsg, u8 *buf) ++{ ++ memcpy(buf, &fsg_bos_desc, USB_DT_BOS_SIZE); ++ buf += USB_DT_BOS_SIZE; ++ ++ memcpy(buf, &fsg_ext_cap_desc, USB_DT_USB_EXT_CAP_SIZE); ++ buf += USB_DT_USB_EXT_CAP_SIZE; ++ ++ memcpy(buf, &fsg_ss_cap_desc, USB_DT_USB_SS_CAP_SIZE); ++ ++ return USB_DT_BOS_SIZE + USB_DT_USB_SS_CAP_SIZE ++ + USB_DT_USB_EXT_CAP_SIZE; ++} ++ ++/* ++ * Config descriptors must agree with the code that sets configurations ++ * and with code managing interfaces and their altsettings. They must ++ * also handle different speeds and other-speed requests. ++ */ ++static int populate_config_buf(struct usb_gadget *gadget, ++ u8 *buf, u8 type, unsigned index) ++{ ++ enum usb_device_speed speed = gadget->speed; ++ int len; ++ const struct usb_descriptor_header **function; ++ ++ if (index > 0) ++ return -EINVAL; ++ ++ if (gadget_is_dualspeed(gadget) && type == USB_DT_OTHER_SPEED_CONFIG) ++ speed = (USB_SPEED_FULL + USB_SPEED_HIGH) - speed; ++ function = gadget_is_dualspeed(gadget) && speed == USB_SPEED_HIGH ++ ? (const struct usb_descriptor_header **)fsg_hs_function ++ : (const struct usb_descriptor_header **)fsg_fs_function; ++ ++ /* for now, don't advertise srp-only devices */ ++ if (!gadget_is_otg(gadget)) ++ function++; ++ ++ len = usb_gadget_config_buf(&config_desc, buf, EP0_BUFSIZE, function); ++ ((struct usb_config_descriptor *) buf)->bDescriptorType = type; ++ return len; ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* These routines may be called in process context or in_irq */ ++ ++/* Caller must hold fsg->lock */ ++static void wakeup_thread(struct fsg_dev *fsg) ++{ ++ /* Tell the main thread that something has happened */ ++ fsg->thread_wakeup_needed = 1; ++ if (fsg->thread_task) ++ wake_up_process(fsg->thread_task); ++} ++ ++ ++static void raise_exception(struct fsg_dev *fsg, enum fsg_state new_state) ++{ ++ unsigned long flags; ++ ++ /* Do nothing if a higher-priority exception is already in progress. ++ * If a lower-or-equal priority exception is in progress, preempt it ++ * and notify the main thread by sending it a signal. */ ++ spin_lock_irqsave(&fsg->lock, flags); ++ if (fsg->state <= new_state) { ++ fsg->exception_req_tag = fsg->ep0_req_tag; ++ fsg->state = new_state; ++ if (fsg->thread_task) ++ send_sig_info(SIGUSR1, SEND_SIG_FORCED, ++ fsg->thread_task); ++ } ++ spin_unlock_irqrestore(&fsg->lock, flags); ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* The disconnect callback and ep0 routines. These always run in_irq, ++ * except that ep0_queue() is called in the main thread to acknowledge ++ * completion of various requests: set config, set interface, and ++ * Bulk-only device reset. */ ++ ++static void fsg_disconnect(struct usb_gadget *gadget) ++{ ++ struct fsg_dev *fsg = get_gadget_data(gadget); ++ ++ DBG(fsg, "disconnect or port reset\n"); ++ raise_exception(fsg, FSG_STATE_DISCONNECT); ++} ++ ++ ++static int ep0_queue(struct fsg_dev *fsg) ++{ ++ int rc; ++ ++ rc = usb_ep_queue(fsg->ep0, fsg->ep0req, GFP_ATOMIC); ++ if (rc != 0 && rc != -ESHUTDOWN) { ++ ++ /* We can't do much more than wait for a reset */ ++ WARNING(fsg, "error in submission: %s --> %d\n", ++ fsg->ep0->name, rc); ++ } ++ return rc; ++} ++ ++static void ep0_complete(struct usb_ep *ep, struct usb_request *req) ++{ ++ struct fsg_dev *fsg = ep->driver_data; ++ ++ if (req->actual > 0) ++ dump_msg(fsg, fsg->ep0req_name, req->buf, req->actual); ++ if (req->status || req->actual != req->length) ++ DBG(fsg, "%s --> %d, %u/%u\n", __func__, ++ req->status, req->actual, req->length); ++ if (req->status == -ECONNRESET) // Request was cancelled ++ usb_ep_fifo_flush(ep); ++ ++ if (req->status == 0 && req->context) ++ ((fsg_routine_t) (req->context))(fsg); ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* Bulk and interrupt endpoint completion handlers. ++ * These always run in_irq. */ ++ ++static void bulk_in_complete(struct usb_ep *ep, struct usb_request *req) ++{ ++ struct fsg_dev *fsg = ep->driver_data; ++ struct fsg_buffhd *bh = req->context; ++ ++ if (req->status || req->actual != req->length) ++ DBG(fsg, "%s --> %d, %u/%u\n", __func__, ++ req->status, req->actual, req->length); ++ if (req->status == -ECONNRESET) // Request was cancelled ++ usb_ep_fifo_flush(ep); ++ ++ /* Hold the lock while we update the request and buffer states */ ++ smp_wmb(); ++ spin_lock(&fsg->lock); ++ bh->inreq_busy = 0; ++ bh->state = BUF_STATE_EMPTY; ++ wakeup_thread(fsg); ++ spin_unlock(&fsg->lock); ++} ++ ++static void bulk_out_complete(struct usb_ep *ep, struct usb_request *req) ++{ ++ struct fsg_dev *fsg = ep->driver_data; ++ struct fsg_buffhd *bh = req->context; ++ ++ dump_msg(fsg, "bulk-out", req->buf, req->actual); ++ if (req->status || req->actual != bh->bulk_out_intended_length) ++ DBG(fsg, "%s --> %d, %u/%u\n", __func__, ++ req->status, req->actual, ++ bh->bulk_out_intended_length); ++ if (req->status == -ECONNRESET) // Request was cancelled ++ usb_ep_fifo_flush(ep); ++ ++ /* Hold the lock while we update the request and buffer states */ ++ smp_wmb(); ++ spin_lock(&fsg->lock); ++ bh->outreq_busy = 0; ++ bh->state = BUF_STATE_FULL; ++ wakeup_thread(fsg); ++ spin_unlock(&fsg->lock); ++} ++ ++ ++#ifdef CONFIG_USB_FILE_STORAGE_TEST ++static void intr_in_complete(struct usb_ep *ep, struct usb_request *req) ++{ ++ struct fsg_dev *fsg = ep->driver_data; ++ struct fsg_buffhd *bh = req->context; ++ ++ if (req->status || req->actual != req->length) ++ DBG(fsg, "%s --> %d, %u/%u\n", __func__, ++ req->status, req->actual, req->length); ++ if (req->status == -ECONNRESET) // Request was cancelled ++ usb_ep_fifo_flush(ep); ++ ++ /* Hold the lock while we update the request and buffer states */ ++ smp_wmb(); ++ spin_lock(&fsg->lock); ++ fsg->intreq_busy = 0; ++ bh->state = BUF_STATE_EMPTY; ++ wakeup_thread(fsg); ++ spin_unlock(&fsg->lock); ++} ++ ++#else ++static void intr_in_complete(struct usb_ep *ep, struct usb_request *req) ++{} ++#endif /* CONFIG_USB_FILE_STORAGE_TEST */ ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* Ep0 class-specific handlers. These always run in_irq. */ ++ ++#ifdef CONFIG_USB_FILE_STORAGE_TEST ++static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh) ++{ ++ struct usb_request *req = fsg->ep0req; ++ static u8 cbi_reset_cmnd[6] = { ++ SEND_DIAGNOSTIC, 4, 0xff, 0xff, 0xff, 0xff}; ++ ++ /* Error in command transfer? */ ++ if (req->status || req->length != req->actual || ++ req->actual < 6 || req->actual > MAX_COMMAND_SIZE) { ++ ++ /* Not all controllers allow a protocol stall after ++ * receiving control-out data, but we'll try anyway. */ ++ fsg_set_halt(fsg, fsg->ep0); ++ return; // Wait for reset ++ } ++ ++ /* Is it the special reset command? */ ++ if (req->actual >= sizeof cbi_reset_cmnd && ++ memcmp(req->buf, cbi_reset_cmnd, ++ sizeof cbi_reset_cmnd) == 0) { ++ ++ /* Raise an exception to stop the current operation ++ * and reinitialize our state. */ ++ DBG(fsg, "cbi reset request\n"); ++ raise_exception(fsg, FSG_STATE_RESET); ++ return; ++ } ++ ++ VDBG(fsg, "CB[I] accept device-specific command\n"); ++ spin_lock(&fsg->lock); ++ ++ /* Save the command for later */ ++ if (fsg->cbbuf_cmnd_size) ++ WARNING(fsg, "CB[I] overwriting previous command\n"); ++ fsg->cbbuf_cmnd_size = req->actual; ++ memcpy(fsg->cbbuf_cmnd, req->buf, fsg->cbbuf_cmnd_size); ++ ++ wakeup_thread(fsg); ++ spin_unlock(&fsg->lock); ++} ++ ++#else ++static void received_cbi_adsc(struct fsg_dev *fsg, struct fsg_buffhd *bh) ++{} ++#endif /* CONFIG_USB_FILE_STORAGE_TEST */ ++ ++ ++static int class_setup_req(struct fsg_dev *fsg, ++ const struct usb_ctrlrequest *ctrl) ++{ ++ struct usb_request *req = fsg->ep0req; ++ int value = -EOPNOTSUPP; ++ u16 w_index = le16_to_cpu(ctrl->wIndex); ++ u16 w_value = le16_to_cpu(ctrl->wValue); ++ u16 w_length = le16_to_cpu(ctrl->wLength); ++ ++ if (!fsg->config) ++ return value; ++ ++ /* Handle Bulk-only class-specific requests */ ++ if (transport_is_bbb()) { ++ switch (ctrl->bRequest) { ++ ++ case US_BULK_RESET_REQUEST: ++ if (ctrl->bRequestType != (USB_DIR_OUT | ++ USB_TYPE_CLASS | USB_RECIP_INTERFACE)) ++ break; ++ if (w_index != 0 || w_value != 0 || w_length != 0) { ++ value = -EDOM; ++ break; ++ } ++ ++ /* Raise an exception to stop the current operation ++ * and reinitialize our state. */ ++ DBG(fsg, "bulk reset request\n"); ++ raise_exception(fsg, FSG_STATE_RESET); ++ value = DELAYED_STATUS; ++ break; ++ ++ case US_BULK_GET_MAX_LUN: ++ if (ctrl->bRequestType != (USB_DIR_IN | ++ USB_TYPE_CLASS | USB_RECIP_INTERFACE)) ++ break; ++ if (w_index != 0 || w_value != 0 || w_length != 1) { ++ value = -EDOM; ++ break; ++ } ++ VDBG(fsg, "get max LUN\n"); ++ *(u8 *) req->buf = fsg->nluns - 1; ++ value = 1; ++ break; ++ } ++ } ++ ++ /* Handle CBI class-specific requests */ ++ else { ++ switch (ctrl->bRequest) { ++ ++ case USB_CBI_ADSC_REQUEST: ++ if (ctrl->bRequestType != (USB_DIR_OUT | ++ USB_TYPE_CLASS | USB_RECIP_INTERFACE)) ++ break; ++ if (w_index != 0 || w_value != 0) { ++ value = -EDOM; ++ break; ++ } ++ if (w_length > MAX_COMMAND_SIZE) { ++ value = -EOVERFLOW; ++ break; ++ } ++ value = w_length; ++ fsg->ep0req->context = received_cbi_adsc; ++ break; ++ } ++ } ++ ++ if (value == -EOPNOTSUPP) ++ VDBG(fsg, ++ "unknown class-specific control req " ++ "%02x.%02x v%04x i%04x l%u\n", ++ ctrl->bRequestType, ctrl->bRequest, ++ le16_to_cpu(ctrl->wValue), w_index, w_length); ++ return value; ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* Ep0 standard request handlers. These always run in_irq. */ ++ ++static int standard_setup_req(struct fsg_dev *fsg, ++ const struct usb_ctrlrequest *ctrl) ++{ ++ struct usb_request *req = fsg->ep0req; ++ int value = -EOPNOTSUPP; ++ u16 w_index = le16_to_cpu(ctrl->wIndex); ++ u16 w_value = le16_to_cpu(ctrl->wValue); ++ ++ /* Usually this just stores reply data in the pre-allocated ep0 buffer, ++ * but config change events will also reconfigure hardware. */ ++ switch (ctrl->bRequest) { ++ ++ case USB_REQ_GET_DESCRIPTOR: ++ if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD | ++ USB_RECIP_DEVICE)) ++ break; ++ switch (w_value >> 8) { ++ ++ case USB_DT_DEVICE: ++ VDBG(fsg, "get device descriptor\n"); ++ device_desc.bMaxPacketSize0 = fsg->ep0->maxpacket; ++ value = sizeof device_desc; ++ memcpy(req->buf, &device_desc, value); ++ break; ++ case USB_DT_DEVICE_QUALIFIER: ++ VDBG(fsg, "get device qualifier\n"); ++ if (!gadget_is_dualspeed(fsg->gadget) || ++ fsg->gadget->speed == USB_SPEED_SUPER) ++ break; ++ /* ++ * Assume ep0 uses the same maxpacket value for both ++ * speeds ++ */ ++ dev_qualifier.bMaxPacketSize0 = fsg->ep0->maxpacket; ++ value = sizeof dev_qualifier; ++ memcpy(req->buf, &dev_qualifier, value); ++ break; ++ ++ case USB_DT_OTHER_SPEED_CONFIG: ++ VDBG(fsg, "get other-speed config descriptor\n"); ++ if (!gadget_is_dualspeed(fsg->gadget) || ++ fsg->gadget->speed == USB_SPEED_SUPER) ++ break; ++ goto get_config; ++ case USB_DT_CONFIG: ++ VDBG(fsg, "get configuration descriptor\n"); ++get_config: ++ value = populate_config_buf(fsg->gadget, ++ req->buf, ++ w_value >> 8, ++ w_value & 0xff); ++ break; ++ ++ case USB_DT_STRING: ++ VDBG(fsg, "get string descriptor\n"); ++ ++ /* wIndex == language code */ ++ value = usb_gadget_get_string(&fsg_stringtab, ++ w_value & 0xff, req->buf); ++ break; ++ ++ case USB_DT_BOS: ++ VDBG(fsg, "get bos descriptor\n"); ++ ++ if (gadget_is_superspeed(fsg->gadget)) ++ value = populate_bos(fsg, req->buf); ++ break; ++ } ++ ++ break; ++ ++ /* One config, two speeds */ ++ case USB_REQ_SET_CONFIGURATION: ++ if (ctrl->bRequestType != (USB_DIR_OUT | USB_TYPE_STANDARD | ++ USB_RECIP_DEVICE)) ++ break; ++ VDBG(fsg, "set configuration\n"); ++ if (w_value == CONFIG_VALUE || w_value == 0) { ++ fsg->new_config = w_value; ++ ++ /* Raise an exception to wipe out previous transaction ++ * state (queued bufs, etc) and set the new config. */ ++ raise_exception(fsg, FSG_STATE_CONFIG_CHANGE); ++ value = DELAYED_STATUS; ++ } ++ break; ++ case USB_REQ_GET_CONFIGURATION: ++ if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD | ++ USB_RECIP_DEVICE)) ++ break; ++ VDBG(fsg, "get configuration\n"); ++ *(u8 *) req->buf = fsg->config; ++ value = 1; ++ break; ++ ++ case USB_REQ_SET_INTERFACE: ++ if (ctrl->bRequestType != (USB_DIR_OUT| USB_TYPE_STANDARD | ++ USB_RECIP_INTERFACE)) ++ break; ++ if (fsg->config && w_index == 0) { ++ ++ /* Raise an exception to wipe out previous transaction ++ * state (queued bufs, etc) and install the new ++ * interface altsetting. */ ++ raise_exception(fsg, FSG_STATE_INTERFACE_CHANGE); ++ value = DELAYED_STATUS; ++ } ++ break; ++ case USB_REQ_GET_INTERFACE: ++ if (ctrl->bRequestType != (USB_DIR_IN | USB_TYPE_STANDARD | ++ USB_RECIP_INTERFACE)) ++ break; ++ if (!fsg->config) ++ break; ++ if (w_index != 0) { ++ value = -EDOM; ++ break; ++ } ++ VDBG(fsg, "get interface\n"); ++ *(u8 *) req->buf = 0; ++ value = 1; ++ break; ++ ++ default: ++ VDBG(fsg, ++ "unknown control req %02x.%02x v%04x i%04x l%u\n", ++ ctrl->bRequestType, ctrl->bRequest, ++ w_value, w_index, le16_to_cpu(ctrl->wLength)); ++ } ++ ++ return value; ++} ++ ++ ++static int fsg_setup(struct usb_gadget *gadget, ++ const struct usb_ctrlrequest *ctrl) ++{ ++ struct fsg_dev *fsg = get_gadget_data(gadget); ++ int rc; ++ int w_length = le16_to_cpu(ctrl->wLength); ++ ++ ++fsg->ep0_req_tag; // Record arrival of a new request ++ fsg->ep0req->context = NULL; ++ fsg->ep0req->length = 0; ++ dump_msg(fsg, "ep0-setup", (u8 *) ctrl, sizeof(*ctrl)); ++ ++ if ((ctrl->bRequestType & USB_TYPE_MASK) == USB_TYPE_CLASS) ++ rc = class_setup_req(fsg, ctrl); ++ else ++ rc = standard_setup_req(fsg, ctrl); ++ ++ /* Respond with data/status or defer until later? */ ++ if (rc >= 0 && rc != DELAYED_STATUS) { ++ rc = min(rc, w_length); ++ fsg->ep0req->length = rc; ++ fsg->ep0req->zero = rc < w_length; ++ fsg->ep0req_name = (ctrl->bRequestType & USB_DIR_IN ? ++ "ep0-in" : "ep0-out"); ++ rc = ep0_queue(fsg); ++ } ++ ++ /* Device either stalls (rc < 0) or reports success */ ++ return rc; ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* All the following routines run in process context */ ++ ++ ++/* Use this for bulk or interrupt transfers, not ep0 */ ++static void start_transfer(struct fsg_dev *fsg, struct usb_ep *ep, ++ struct usb_request *req, int *pbusy, ++ enum fsg_buffer_state *state) ++{ ++ int rc; ++ ++ if (ep == fsg->bulk_in) ++ dump_msg(fsg, "bulk-in", req->buf, req->length); ++ else if (ep == fsg->intr_in) ++ dump_msg(fsg, "intr-in", req->buf, req->length); ++ ++ spin_lock_irq(&fsg->lock); ++ *pbusy = 1; ++ *state = BUF_STATE_BUSY; ++ spin_unlock_irq(&fsg->lock); ++ rc = usb_ep_queue(ep, req, GFP_KERNEL); ++ if (rc != 0) { ++ *pbusy = 0; ++ *state = BUF_STATE_EMPTY; ++ ++ /* We can't do much more than wait for a reset */ ++ ++ /* Note: currently the net2280 driver fails zero-length ++ * submissions if DMA is enabled. */ ++ if (rc != -ESHUTDOWN && !(rc == -EOPNOTSUPP && ++ req->length == 0)) ++ WARNING(fsg, "error in submission: %s --> %d\n", ++ ep->name, rc); ++ } ++} ++ ++ ++static int sleep_thread(struct fsg_dev *fsg) ++{ ++ int rc = 0; ++ ++ /* Wait until a signal arrives or we are woken up */ ++ for (;;) { ++ try_to_freeze(); ++ set_current_state(TASK_INTERRUPTIBLE); ++ if (signal_pending(current)) { ++ rc = -EINTR; ++ break; ++ } ++ if (fsg->thread_wakeup_needed) ++ break; ++ schedule(); ++ } ++ __set_current_state(TASK_RUNNING); ++ fsg->thread_wakeup_needed = 0; ++ return rc; ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static int do_read(struct fsg_dev *fsg) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ u32 lba; ++ struct fsg_buffhd *bh; ++ int rc; ++ u32 amount_left; ++ loff_t file_offset, file_offset_tmp; ++ unsigned int amount; ++ ssize_t nread; ++ ++ /* Get the starting Logical Block Address and check that it's ++ * not too big */ ++ if (fsg->cmnd[0] == READ_6) ++ lba = get_unaligned_be24(&fsg->cmnd[1]); ++ else { ++ lba = get_unaligned_be32(&fsg->cmnd[2]); ++ ++ /* We allow DPO (Disable Page Out = don't save data in the ++ * cache) and FUA (Force Unit Access = don't read from the ++ * cache), but we don't implement them. */ ++ if ((fsg->cmnd[1] & ~0x18) != 0) { ++ curlun->sense_data = SS_INVALID_FIELD_IN_CDB; ++ return -EINVAL; ++ } ++ } ++ if (lba >= curlun->num_sectors) { ++ curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; ++ return -EINVAL; ++ } ++ file_offset = ((loff_t) lba) << curlun->blkbits; ++ ++ /* Carry out the file reads */ ++ amount_left = fsg->data_size_from_cmnd; ++ if (unlikely(amount_left == 0)) ++ return -EIO; // No default reply ++ ++ for (;;) { ++ ++ /* Figure out how much we need to read: ++ * Try to read the remaining amount. ++ * But don't read more than the buffer size. ++ * And don't try to read past the end of the file. ++ */ ++ amount = min((unsigned int) amount_left, mod_data.buflen); ++ amount = min((loff_t) amount, ++ curlun->file_length - file_offset); ++ ++ /* Wait for the next buffer to become available */ ++ bh = fsg->next_buffhd_to_fill; ++ while (bh->state != BUF_STATE_EMPTY) { ++ rc = sleep_thread(fsg); ++ if (rc) ++ return rc; ++ } ++ ++ /* If we were asked to read past the end of file, ++ * end with an empty buffer. */ ++ if (amount == 0) { ++ curlun->sense_data = ++ SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; ++ curlun->sense_data_info = file_offset >> curlun->blkbits; ++ curlun->info_valid = 1; ++ bh->inreq->length = 0; ++ bh->state = BUF_STATE_FULL; ++ break; ++ } ++ ++ /* Perform the read */ ++ file_offset_tmp = file_offset; ++ nread = vfs_read(curlun->filp, ++ (char __user *) bh->buf, ++ amount, &file_offset_tmp); ++ VLDBG(curlun, "file read %u @ %llu -> %d\n", amount, ++ (unsigned long long) file_offset, ++ (int) nread); ++ if (signal_pending(current)) ++ return -EINTR; ++ ++ if (nread < 0) { ++ LDBG(curlun, "error in file read: %d\n", ++ (int) nread); ++ nread = 0; ++ } else if (nread < amount) { ++ LDBG(curlun, "partial file read: %d/%u\n", ++ (int) nread, amount); ++ nread = round_down(nread, curlun->blksize); ++ } ++ file_offset += nread; ++ amount_left -= nread; ++ fsg->residue -= nread; ++ ++ /* Except at the end of the transfer, nread will be ++ * equal to the buffer size, which is divisible by the ++ * bulk-in maxpacket size. ++ */ ++ bh->inreq->length = nread; ++ bh->state = BUF_STATE_FULL; ++ ++ /* If an error occurred, report it and its position */ ++ if (nread < amount) { ++ curlun->sense_data = SS_UNRECOVERED_READ_ERROR; ++ curlun->sense_data_info = file_offset >> curlun->blkbits; ++ curlun->info_valid = 1; ++ break; ++ } ++ ++ if (amount_left == 0) ++ break; // No more left to read ++ ++ /* Send this buffer and go read some more */ ++ bh->inreq->zero = 0; ++ start_transfer(fsg, fsg->bulk_in, bh->inreq, ++ &bh->inreq_busy, &bh->state); ++ fsg->next_buffhd_to_fill = bh->next; ++ } ++ ++ return -EIO; // No default reply ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static int do_write(struct fsg_dev *fsg) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ u32 lba; ++ struct fsg_buffhd *bh; ++ int get_some_more; ++ u32 amount_left_to_req, amount_left_to_write; ++ loff_t usb_offset, file_offset, file_offset_tmp; ++ unsigned int amount; ++ ssize_t nwritten; ++ int rc; ++ ++ if (curlun->ro) { ++ curlun->sense_data = SS_WRITE_PROTECTED; ++ return -EINVAL; ++ } ++ spin_lock(&curlun->filp->f_lock); ++ curlun->filp->f_flags &= ~O_SYNC; // Default is not to wait ++ spin_unlock(&curlun->filp->f_lock); ++ ++ /* Get the starting Logical Block Address and check that it's ++ * not too big */ ++ if (fsg->cmnd[0] == WRITE_6) ++ lba = get_unaligned_be24(&fsg->cmnd[1]); ++ else { ++ lba = get_unaligned_be32(&fsg->cmnd[2]); ++ ++ /* We allow DPO (Disable Page Out = don't save data in the ++ * cache) and FUA (Force Unit Access = write directly to the ++ * medium). We don't implement DPO; we implement FUA by ++ * performing synchronous output. */ ++ if ((fsg->cmnd[1] & ~0x18) != 0) { ++ curlun->sense_data = SS_INVALID_FIELD_IN_CDB; ++ return -EINVAL; ++ } ++ /* FUA */ ++ if (!curlun->nofua && (fsg->cmnd[1] & 0x08)) { ++ spin_lock(&curlun->filp->f_lock); ++ curlun->filp->f_flags |= O_DSYNC; ++ spin_unlock(&curlun->filp->f_lock); ++ } ++ } ++ if (lba >= curlun->num_sectors) { ++ curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; ++ return -EINVAL; ++ } ++ ++ /* Carry out the file writes */ ++ get_some_more = 1; ++ file_offset = usb_offset = ((loff_t) lba) << curlun->blkbits; ++ amount_left_to_req = amount_left_to_write = fsg->data_size_from_cmnd; ++ ++ while (amount_left_to_write > 0) { ++ ++ /* Queue a request for more data from the host */ ++ bh = fsg->next_buffhd_to_fill; ++ if (bh->state == BUF_STATE_EMPTY && get_some_more) { ++ ++ /* Figure out how much we want to get: ++ * Try to get the remaining amount, ++ * but not more than the buffer size. ++ */ ++ amount = min(amount_left_to_req, mod_data.buflen); ++ ++ /* Beyond the end of the backing file? */ ++ if (usb_offset >= curlun->file_length) { ++ get_some_more = 0; ++ curlun->sense_data = ++ SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; ++ curlun->sense_data_info = usb_offset >> curlun->blkbits; ++ curlun->info_valid = 1; ++ continue; ++ } ++ ++ /* Get the next buffer */ ++ usb_offset += amount; ++ fsg->usb_amount_left -= amount; ++ amount_left_to_req -= amount; ++ if (amount_left_to_req == 0) ++ get_some_more = 0; ++ ++ /* Except at the end of the transfer, amount will be ++ * equal to the buffer size, which is divisible by ++ * the bulk-out maxpacket size. ++ */ ++ set_bulk_out_req_length(fsg, bh, amount); ++ start_transfer(fsg, fsg->bulk_out, bh->outreq, ++ &bh->outreq_busy, &bh->state); ++ fsg->next_buffhd_to_fill = bh->next; ++ continue; ++ } ++ ++ /* Write the received data to the backing file */ ++ bh = fsg->next_buffhd_to_drain; ++ if (bh->state == BUF_STATE_EMPTY && !get_some_more) ++ break; // We stopped early ++ if (bh->state == BUF_STATE_FULL) { ++ smp_rmb(); ++ fsg->next_buffhd_to_drain = bh->next; ++ bh->state = BUF_STATE_EMPTY; ++ ++ /* Did something go wrong with the transfer? */ ++ if (bh->outreq->status != 0) { ++ curlun->sense_data = SS_COMMUNICATION_FAILURE; ++ curlun->sense_data_info = file_offset >> curlun->blkbits; ++ curlun->info_valid = 1; ++ break; ++ } ++ ++ amount = bh->outreq->actual; ++ if (curlun->file_length - file_offset < amount) { ++ LERROR(curlun, ++ "write %u @ %llu beyond end %llu\n", ++ amount, (unsigned long long) file_offset, ++ (unsigned long long) curlun->file_length); ++ amount = curlun->file_length - file_offset; ++ } ++ ++ /* Don't accept excess data. The spec doesn't say ++ * what to do in this case. We'll ignore the error. ++ */ ++ amount = min(amount, bh->bulk_out_intended_length); ++ ++ /* Don't write a partial block */ ++ amount = round_down(amount, curlun->blksize); ++ if (amount == 0) ++ goto empty_write; ++ ++ /* Perform the write */ ++ file_offset_tmp = file_offset; ++ nwritten = vfs_write(curlun->filp, ++ (char __user *) bh->buf, ++ amount, &file_offset_tmp); ++ VLDBG(curlun, "file write %u @ %llu -> %d\n", amount, ++ (unsigned long long) file_offset, ++ (int) nwritten); ++ if (signal_pending(current)) ++ return -EINTR; // Interrupted! ++ ++ if (nwritten < 0) { ++ LDBG(curlun, "error in file write: %d\n", ++ (int) nwritten); ++ nwritten = 0; ++ } else if (nwritten < amount) { ++ LDBG(curlun, "partial file write: %d/%u\n", ++ (int) nwritten, amount); ++ nwritten = round_down(nwritten, curlun->blksize); ++ } ++ file_offset += nwritten; ++ amount_left_to_write -= nwritten; ++ fsg->residue -= nwritten; ++ ++ /* If an error occurred, report it and its position */ ++ if (nwritten < amount) { ++ curlun->sense_data = SS_WRITE_ERROR; ++ curlun->sense_data_info = file_offset >> curlun->blkbits; ++ curlun->info_valid = 1; ++ break; ++ } ++ ++ empty_write: ++ /* Did the host decide to stop early? */ ++ if (bh->outreq->actual < bh->bulk_out_intended_length) { ++ fsg->short_packet_received = 1; ++ break; ++ } ++ continue; ++ } ++ ++ /* Wait for something to happen */ ++ rc = sleep_thread(fsg); ++ if (rc) ++ return rc; ++ } ++ ++ return -EIO; // No default reply ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static int do_synchronize_cache(struct fsg_dev *fsg) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ int rc; ++ ++ /* We ignore the requested LBA and write out all file's ++ * dirty data buffers. */ ++ rc = fsg_lun_fsync_sub(curlun); ++ if (rc) ++ curlun->sense_data = SS_WRITE_ERROR; ++ return 0; ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static void invalidate_sub(struct fsg_lun *curlun) ++{ ++ struct file *filp = curlun->filp; ++ struct inode *inode = filp->f_path.dentry->d_inode; ++ unsigned long rc; ++ ++ rc = invalidate_mapping_pages(inode->i_mapping, 0, -1); ++ VLDBG(curlun, "invalidate_mapping_pages -> %ld\n", rc); ++} ++ ++static int do_verify(struct fsg_dev *fsg) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ u32 lba; ++ u32 verification_length; ++ struct fsg_buffhd *bh = fsg->next_buffhd_to_fill; ++ loff_t file_offset, file_offset_tmp; ++ u32 amount_left; ++ unsigned int amount; ++ ssize_t nread; ++ ++ /* Get the starting Logical Block Address and check that it's ++ * not too big */ ++ lba = get_unaligned_be32(&fsg->cmnd[2]); ++ if (lba >= curlun->num_sectors) { ++ curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; ++ return -EINVAL; ++ } ++ ++ /* We allow DPO (Disable Page Out = don't save data in the ++ * cache) but we don't implement it. */ ++ if ((fsg->cmnd[1] & ~0x10) != 0) { ++ curlun->sense_data = SS_INVALID_FIELD_IN_CDB; ++ return -EINVAL; ++ } ++ ++ verification_length = get_unaligned_be16(&fsg->cmnd[7]); ++ if (unlikely(verification_length == 0)) ++ return -EIO; // No default reply ++ ++ /* Prepare to carry out the file verify */ ++ amount_left = verification_length << curlun->blkbits; ++ file_offset = ((loff_t) lba) << curlun->blkbits; ++ ++ /* Write out all the dirty buffers before invalidating them */ ++ fsg_lun_fsync_sub(curlun); ++ if (signal_pending(current)) ++ return -EINTR; ++ ++ invalidate_sub(curlun); ++ if (signal_pending(current)) ++ return -EINTR; ++ ++ /* Just try to read the requested blocks */ ++ while (amount_left > 0) { ++ ++ /* Figure out how much we need to read: ++ * Try to read the remaining amount, but not more than ++ * the buffer size. ++ * And don't try to read past the end of the file. ++ */ ++ amount = min((unsigned int) amount_left, mod_data.buflen); ++ amount = min((loff_t) amount, ++ curlun->file_length - file_offset); ++ if (amount == 0) { ++ curlun->sense_data = ++ SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; ++ curlun->sense_data_info = file_offset >> curlun->blkbits; ++ curlun->info_valid = 1; ++ break; ++ } ++ ++ /* Perform the read */ ++ file_offset_tmp = file_offset; ++ nread = vfs_read(curlun->filp, ++ (char __user *) bh->buf, ++ amount, &file_offset_tmp); ++ VLDBG(curlun, "file read %u @ %llu -> %d\n", amount, ++ (unsigned long long) file_offset, ++ (int) nread); ++ if (signal_pending(current)) ++ return -EINTR; ++ ++ if (nread < 0) { ++ LDBG(curlun, "error in file verify: %d\n", ++ (int) nread); ++ nread = 0; ++ } else if (nread < amount) { ++ LDBG(curlun, "partial file verify: %d/%u\n", ++ (int) nread, amount); ++ nread = round_down(nread, curlun->blksize); ++ } ++ if (nread == 0) { ++ curlun->sense_data = SS_UNRECOVERED_READ_ERROR; ++ curlun->sense_data_info = file_offset >> curlun->blkbits; ++ curlun->info_valid = 1; ++ break; ++ } ++ file_offset += nread; ++ amount_left -= nread; ++ } ++ return 0; ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static int do_inquiry(struct fsg_dev *fsg, struct fsg_buffhd *bh) ++{ ++ u8 *buf = (u8 *) bh->buf; ++ ++ static char vendor_id[] = "Linux "; ++ static char product_disk_id[] = "File-Stor Gadget"; ++ static char product_cdrom_id[] = "File-CD Gadget "; ++ ++ if (!fsg->curlun) { // Unsupported LUNs are okay ++ fsg->bad_lun_okay = 1; ++ memset(buf, 0, 36); ++ buf[0] = 0x7f; // Unsupported, no device-type ++ buf[4] = 31; // Additional length ++ return 36; ++ } ++ ++ memset(buf, 0, 8); ++ buf[0] = (mod_data.cdrom ? TYPE_ROM : TYPE_DISK); ++ if (mod_data.removable) ++ buf[1] = 0x80; ++ buf[2] = 2; // ANSI SCSI level 2 ++ buf[3] = 2; // SCSI-2 INQUIRY data format ++ buf[4] = 31; // Additional length ++ // No special options ++ sprintf(buf + 8, "%-8s%-16s%04x", vendor_id, ++ (mod_data.cdrom ? product_cdrom_id : ++ product_disk_id), ++ mod_data.release); ++ return 36; ++} ++ ++ ++static int do_request_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ u8 *buf = (u8 *) bh->buf; ++ u32 sd, sdinfo; ++ int valid; ++ ++ /* ++ * From the SCSI-2 spec., section 7.9 (Unit attention condition): ++ * ++ * If a REQUEST SENSE command is received from an initiator ++ * with a pending unit attention condition (before the target ++ * generates the contingent allegiance condition), then the ++ * target shall either: ++ * a) report any pending sense data and preserve the unit ++ * attention condition on the logical unit, or, ++ * b) report the unit attention condition, may discard any ++ * pending sense data, and clear the unit attention ++ * condition on the logical unit for that initiator. ++ * ++ * FSG normally uses option a); enable this code to use option b). ++ */ ++#if 0 ++ if (curlun && curlun->unit_attention_data != SS_NO_SENSE) { ++ curlun->sense_data = curlun->unit_attention_data; ++ curlun->unit_attention_data = SS_NO_SENSE; ++ } ++#endif ++ ++ if (!curlun) { // Unsupported LUNs are okay ++ fsg->bad_lun_okay = 1; ++ sd = SS_LOGICAL_UNIT_NOT_SUPPORTED; ++ sdinfo = 0; ++ valid = 0; ++ } else { ++ sd = curlun->sense_data; ++ sdinfo = curlun->sense_data_info; ++ valid = curlun->info_valid << 7; ++ curlun->sense_data = SS_NO_SENSE; ++ curlun->sense_data_info = 0; ++ curlun->info_valid = 0; ++ } ++ ++ memset(buf, 0, 18); ++ buf[0] = valid | 0x70; // Valid, current error ++ buf[2] = SK(sd); ++ put_unaligned_be32(sdinfo, &buf[3]); /* Sense information */ ++ buf[7] = 18 - 8; // Additional sense length ++ buf[12] = ASC(sd); ++ buf[13] = ASCQ(sd); ++ return 18; ++} ++ ++ ++static int do_read_capacity(struct fsg_dev *fsg, struct fsg_buffhd *bh) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ u32 lba = get_unaligned_be32(&fsg->cmnd[2]); ++ int pmi = fsg->cmnd[8]; ++ u8 *buf = (u8 *) bh->buf; ++ ++ /* Check the PMI and LBA fields */ ++ if (pmi > 1 || (pmi == 0 && lba != 0)) { ++ curlun->sense_data = SS_INVALID_FIELD_IN_CDB; ++ return -EINVAL; ++ } ++ ++ put_unaligned_be32(curlun->num_sectors - 1, &buf[0]); ++ /* Max logical block */ ++ put_unaligned_be32(curlun->blksize, &buf[4]); /* Block length */ ++ return 8; ++} ++ ++ ++static int do_read_header(struct fsg_dev *fsg, struct fsg_buffhd *bh) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ int msf = fsg->cmnd[1] & 0x02; ++ u32 lba = get_unaligned_be32(&fsg->cmnd[2]); ++ u8 *buf = (u8 *) bh->buf; ++ ++ if ((fsg->cmnd[1] & ~0x02) != 0) { /* Mask away MSF */ ++ curlun->sense_data = SS_INVALID_FIELD_IN_CDB; ++ return -EINVAL; ++ } ++ if (lba >= curlun->num_sectors) { ++ curlun->sense_data = SS_LOGICAL_BLOCK_ADDRESS_OUT_OF_RANGE; ++ return -EINVAL; ++ } ++ ++ memset(buf, 0, 8); ++ buf[0] = 0x01; /* 2048 bytes of user data, rest is EC */ ++ store_cdrom_address(&buf[4], msf, lba); ++ return 8; ++} ++ ++ ++static int do_read_toc(struct fsg_dev *fsg, struct fsg_buffhd *bh) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ int msf = fsg->cmnd[1] & 0x02; ++ int start_track = fsg->cmnd[6]; ++ u8 *buf = (u8 *) bh->buf; ++ ++ if ((fsg->cmnd[1] & ~0x02) != 0 || /* Mask away MSF */ ++ start_track > 1) { ++ curlun->sense_data = SS_INVALID_FIELD_IN_CDB; ++ return -EINVAL; ++ } ++ ++ memset(buf, 0, 20); ++ buf[1] = (20-2); /* TOC data length */ ++ buf[2] = 1; /* First track number */ ++ buf[3] = 1; /* Last track number */ ++ buf[5] = 0x16; /* Data track, copying allowed */ ++ buf[6] = 0x01; /* Only track is number 1 */ ++ store_cdrom_address(&buf[8], msf, 0); ++ ++ buf[13] = 0x16; /* Lead-out track is data */ ++ buf[14] = 0xAA; /* Lead-out track number */ ++ store_cdrom_address(&buf[16], msf, curlun->num_sectors); ++ return 20; ++} ++ ++ ++static int do_mode_sense(struct fsg_dev *fsg, struct fsg_buffhd *bh) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ int mscmnd = fsg->cmnd[0]; ++ u8 *buf = (u8 *) bh->buf; ++ u8 *buf0 = buf; ++ int pc, page_code; ++ int changeable_values, all_pages; ++ int valid_page = 0; ++ int len, limit; ++ ++ if ((fsg->cmnd[1] & ~0x08) != 0) { // Mask away DBD ++ curlun->sense_data = SS_INVALID_FIELD_IN_CDB; ++ return -EINVAL; ++ } ++ pc = fsg->cmnd[2] >> 6; ++ page_code = fsg->cmnd[2] & 0x3f; ++ if (pc == 3) { ++ curlun->sense_data = SS_SAVING_PARAMETERS_NOT_SUPPORTED; ++ return -EINVAL; ++ } ++ changeable_values = (pc == 1); ++ all_pages = (page_code == 0x3f); ++ ++ /* Write the mode parameter header. Fixed values are: default ++ * medium type, no cache control (DPOFUA), and no block descriptors. ++ * The only variable value is the WriteProtect bit. We will fill in ++ * the mode data length later. */ ++ memset(buf, 0, 8); ++ if (mscmnd == MODE_SENSE) { ++ buf[2] = (curlun->ro ? 0x80 : 0x00); // WP, DPOFUA ++ buf += 4; ++ limit = 255; ++ } else { // MODE_SENSE_10 ++ buf[3] = (curlun->ro ? 0x80 : 0x00); // WP, DPOFUA ++ buf += 8; ++ limit = 65535; // Should really be mod_data.buflen ++ } ++ ++ /* No block descriptors */ ++ ++ /* The mode pages, in numerical order. The only page we support ++ * is the Caching page. */ ++ if (page_code == 0x08 || all_pages) { ++ valid_page = 1; ++ buf[0] = 0x08; // Page code ++ buf[1] = 10; // Page length ++ memset(buf+2, 0, 10); // None of the fields are changeable ++ ++ if (!changeable_values) { ++ buf[2] = 0x04; // Write cache enable, ++ // Read cache not disabled ++ // No cache retention priorities ++ put_unaligned_be16(0xffff, &buf[4]); ++ /* Don't disable prefetch */ ++ /* Minimum prefetch = 0 */ ++ put_unaligned_be16(0xffff, &buf[8]); ++ /* Maximum prefetch */ ++ put_unaligned_be16(0xffff, &buf[10]); ++ /* Maximum prefetch ceiling */ ++ } ++ buf += 12; ++ } ++ ++ /* Check that a valid page was requested and the mode data length ++ * isn't too long. */ ++ len = buf - buf0; ++ if (!valid_page || len > limit) { ++ curlun->sense_data = SS_INVALID_FIELD_IN_CDB; ++ return -EINVAL; ++ } ++ ++ /* Store the mode data length */ ++ if (mscmnd == MODE_SENSE) ++ buf0[0] = len - 1; ++ else ++ put_unaligned_be16(len - 2, buf0); ++ return len; ++} ++ ++ ++static int do_start_stop(struct fsg_dev *fsg) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ int loej, start; ++ ++ if (!mod_data.removable) { ++ curlun->sense_data = SS_INVALID_COMMAND; ++ return -EINVAL; ++ } ++ ++ // int immed = fsg->cmnd[1] & 0x01; ++ loej = fsg->cmnd[4] & 0x02; ++ start = fsg->cmnd[4] & 0x01; ++ ++#ifdef CONFIG_USB_FILE_STORAGE_TEST ++ if ((fsg->cmnd[1] & ~0x01) != 0 || // Mask away Immed ++ (fsg->cmnd[4] & ~0x03) != 0) { // Mask LoEj, Start ++ curlun->sense_data = SS_INVALID_FIELD_IN_CDB; ++ return -EINVAL; ++ } ++ ++ if (!start) { ++ ++ /* Are we allowed to unload the media? */ ++ if (curlun->prevent_medium_removal) { ++ LDBG(curlun, "unload attempt prevented\n"); ++ curlun->sense_data = SS_MEDIUM_REMOVAL_PREVENTED; ++ return -EINVAL; ++ } ++ if (loej) { // Simulate an unload/eject ++ up_read(&fsg->filesem); ++ down_write(&fsg->filesem); ++ fsg_lun_close(curlun); ++ up_write(&fsg->filesem); ++ down_read(&fsg->filesem); ++ } ++ } else { ++ ++ /* Our emulation doesn't support mounting; the medium is ++ * available for use as soon as it is loaded. */ ++ if (!fsg_lun_is_open(curlun)) { ++ curlun->sense_data = SS_MEDIUM_NOT_PRESENT; ++ return -EINVAL; ++ } ++ } ++#endif ++ return 0; ++} ++ ++ ++static int do_prevent_allow(struct fsg_dev *fsg) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ int prevent; ++ ++ if (!mod_data.removable) { ++ curlun->sense_data = SS_INVALID_COMMAND; ++ return -EINVAL; ++ } ++ ++ prevent = fsg->cmnd[4] & 0x01; ++ if ((fsg->cmnd[4] & ~0x01) != 0) { // Mask away Prevent ++ curlun->sense_data = SS_INVALID_FIELD_IN_CDB; ++ return -EINVAL; ++ } ++ ++ if (curlun->prevent_medium_removal && !prevent) ++ fsg_lun_fsync_sub(curlun); ++ curlun->prevent_medium_removal = prevent; ++ return 0; ++} ++ ++ ++static int do_read_format_capacities(struct fsg_dev *fsg, ++ struct fsg_buffhd *bh) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ u8 *buf = (u8 *) bh->buf; ++ ++ buf[0] = buf[1] = buf[2] = 0; ++ buf[3] = 8; // Only the Current/Maximum Capacity Descriptor ++ buf += 4; ++ ++ put_unaligned_be32(curlun->num_sectors, &buf[0]); ++ /* Number of blocks */ ++ put_unaligned_be32(curlun->blksize, &buf[4]); /* Block length */ ++ buf[4] = 0x02; /* Current capacity */ ++ return 12; ++} ++ ++ ++static int do_mode_select(struct fsg_dev *fsg, struct fsg_buffhd *bh) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ ++ /* We don't support MODE SELECT */ ++ curlun->sense_data = SS_INVALID_COMMAND; ++ return -EINVAL; ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static int halt_bulk_in_endpoint(struct fsg_dev *fsg) ++{ ++ int rc; ++ ++ rc = fsg_set_halt(fsg, fsg->bulk_in); ++ if (rc == -EAGAIN) ++ VDBG(fsg, "delayed bulk-in endpoint halt\n"); ++ while (rc != 0) { ++ if (rc != -EAGAIN) { ++ WARNING(fsg, "usb_ep_set_halt -> %d\n", rc); ++ rc = 0; ++ break; ++ } ++ ++ /* Wait for a short time and then try again */ ++ if (msleep_interruptible(100) != 0) ++ return -EINTR; ++ rc = usb_ep_set_halt(fsg->bulk_in); ++ } ++ return rc; ++} ++ ++static int wedge_bulk_in_endpoint(struct fsg_dev *fsg) ++{ ++ int rc; ++ ++ DBG(fsg, "bulk-in set wedge\n"); ++ rc = usb_ep_set_wedge(fsg->bulk_in); ++ if (rc == -EAGAIN) ++ VDBG(fsg, "delayed bulk-in endpoint wedge\n"); ++ while (rc != 0) { ++ if (rc != -EAGAIN) { ++ WARNING(fsg, "usb_ep_set_wedge -> %d\n", rc); ++ rc = 0; ++ break; ++ } ++ ++ /* Wait for a short time and then try again */ ++ if (msleep_interruptible(100) != 0) ++ return -EINTR; ++ rc = usb_ep_set_wedge(fsg->bulk_in); ++ } ++ return rc; ++} ++ ++static int throw_away_data(struct fsg_dev *fsg) ++{ ++ struct fsg_buffhd *bh; ++ u32 amount; ++ int rc; ++ ++ while ((bh = fsg->next_buffhd_to_drain)->state != BUF_STATE_EMPTY || ++ fsg->usb_amount_left > 0) { ++ ++ /* Throw away the data in a filled buffer */ ++ if (bh->state == BUF_STATE_FULL) { ++ smp_rmb(); ++ bh->state = BUF_STATE_EMPTY; ++ fsg->next_buffhd_to_drain = bh->next; ++ ++ /* A short packet or an error ends everything */ ++ if (bh->outreq->actual < bh->bulk_out_intended_length || ++ bh->outreq->status != 0) { ++ raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT); ++ return -EINTR; ++ } ++ continue; ++ } ++ ++ /* Try to submit another request if we need one */ ++ bh = fsg->next_buffhd_to_fill; ++ if (bh->state == BUF_STATE_EMPTY && fsg->usb_amount_left > 0) { ++ amount = min(fsg->usb_amount_left, ++ (u32) mod_data.buflen); ++ ++ /* Except at the end of the transfer, amount will be ++ * equal to the buffer size, which is divisible by ++ * the bulk-out maxpacket size. ++ */ ++ set_bulk_out_req_length(fsg, bh, amount); ++ start_transfer(fsg, fsg->bulk_out, bh->outreq, ++ &bh->outreq_busy, &bh->state); ++ fsg->next_buffhd_to_fill = bh->next; ++ fsg->usb_amount_left -= amount; ++ continue; ++ } ++ ++ /* Otherwise wait for something to happen */ ++ rc = sleep_thread(fsg); ++ if (rc) ++ return rc; ++ } ++ return 0; ++} ++ ++ ++static int finish_reply(struct fsg_dev *fsg) ++{ ++ struct fsg_buffhd *bh = fsg->next_buffhd_to_fill; ++ int rc = 0; ++ ++ switch (fsg->data_dir) { ++ case DATA_DIR_NONE: ++ break; // Nothing to send ++ ++ /* If we don't know whether the host wants to read or write, ++ * this must be CB or CBI with an unknown command. We mustn't ++ * try to send or receive any data. So stall both bulk pipes ++ * if we can and wait for a reset. */ ++ case DATA_DIR_UNKNOWN: ++ if (mod_data.can_stall) { ++ fsg_set_halt(fsg, fsg->bulk_out); ++ rc = halt_bulk_in_endpoint(fsg); ++ } ++ break; ++ ++ /* All but the last buffer of data must have already been sent */ ++ case DATA_DIR_TO_HOST: ++ if (fsg->data_size == 0) ++ ; // Nothing to send ++ ++ /* If there's no residue, simply send the last buffer */ ++ else if (fsg->residue == 0) { ++ bh->inreq->zero = 0; ++ start_transfer(fsg, fsg->bulk_in, bh->inreq, ++ &bh->inreq_busy, &bh->state); ++ fsg->next_buffhd_to_fill = bh->next; ++ } ++ ++ /* There is a residue. For CB and CBI, simply mark the end ++ * of the data with a short packet. However, if we are ++ * allowed to stall, there was no data at all (residue == ++ * data_size), and the command failed (invalid LUN or ++ * sense data is set), then halt the bulk-in endpoint ++ * instead. */ ++ else if (!transport_is_bbb()) { ++ if (mod_data.can_stall && ++ fsg->residue == fsg->data_size && ++ (!fsg->curlun || fsg->curlun->sense_data != SS_NO_SENSE)) { ++ bh->state = BUF_STATE_EMPTY; ++ rc = halt_bulk_in_endpoint(fsg); ++ } else { ++ bh->inreq->zero = 1; ++ start_transfer(fsg, fsg->bulk_in, bh->inreq, ++ &bh->inreq_busy, &bh->state); ++ fsg->next_buffhd_to_fill = bh->next; ++ } ++ } ++ ++ /* ++ * For Bulk-only, mark the end of the data with a short ++ * packet. If we are allowed to stall, halt the bulk-in ++ * endpoint. (Note: This violates the Bulk-Only Transport ++ * specification, which requires us to pad the data if we ++ * don't halt the endpoint. Presumably nobody will mind.) ++ */ ++ else { ++ bh->inreq->zero = 1; ++ start_transfer(fsg, fsg->bulk_in, bh->inreq, ++ &bh->inreq_busy, &bh->state); ++ fsg->next_buffhd_to_fill = bh->next; ++ if (mod_data.can_stall) ++ rc = halt_bulk_in_endpoint(fsg); ++ } ++ break; ++ ++ /* We have processed all we want from the data the host has sent. ++ * There may still be outstanding bulk-out requests. */ ++ case DATA_DIR_FROM_HOST: ++ if (fsg->residue == 0) ++ ; // Nothing to receive ++ ++ /* Did the host stop sending unexpectedly early? */ ++ else if (fsg->short_packet_received) { ++ raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT); ++ rc = -EINTR; ++ } ++ ++ /* We haven't processed all the incoming data. Even though ++ * we may be allowed to stall, doing so would cause a race. ++ * The controller may already have ACK'ed all the remaining ++ * bulk-out packets, in which case the host wouldn't see a ++ * STALL. Not realizing the endpoint was halted, it wouldn't ++ * clear the halt -- leading to problems later on. */ ++#if 0 ++ else if (mod_data.can_stall) { ++ fsg_set_halt(fsg, fsg->bulk_out); ++ raise_exception(fsg, FSG_STATE_ABORT_BULK_OUT); ++ rc = -EINTR; ++ } ++#endif ++ ++ /* We can't stall. Read in the excess data and throw it ++ * all away. */ ++ else ++ rc = throw_away_data(fsg); ++ break; ++ } ++ return rc; ++} ++ ++ ++static int send_status(struct fsg_dev *fsg) ++{ ++ struct fsg_lun *curlun = fsg->curlun; ++ struct fsg_buffhd *bh; ++ int rc; ++ u8 status = US_BULK_STAT_OK; ++ u32 sd, sdinfo = 0; ++ ++ /* Wait for the next buffer to become available */ ++ bh = fsg->next_buffhd_to_fill; ++ while (bh->state != BUF_STATE_EMPTY) { ++ rc = sleep_thread(fsg); ++ if (rc) ++ return rc; ++ } ++ ++ if (curlun) { ++ sd = curlun->sense_data; ++ sdinfo = curlun->sense_data_info; ++ } else if (fsg->bad_lun_okay) ++ sd = SS_NO_SENSE; ++ else ++ sd = SS_LOGICAL_UNIT_NOT_SUPPORTED; ++ ++ if (fsg->phase_error) { ++ DBG(fsg, "sending phase-error status\n"); ++ status = US_BULK_STAT_PHASE; ++ sd = SS_INVALID_COMMAND; ++ } else if (sd != SS_NO_SENSE) { ++ DBG(fsg, "sending command-failure status\n"); ++ status = US_BULK_STAT_FAIL; ++ VDBG(fsg, " sense data: SK x%02x, ASC x%02x, ASCQ x%02x;" ++ " info x%x\n", ++ SK(sd), ASC(sd), ASCQ(sd), sdinfo); ++ } ++ ++ if (transport_is_bbb()) { ++ struct bulk_cs_wrap *csw = bh->buf; ++ ++ /* Store and send the Bulk-only CSW */ ++ csw->Signature = cpu_to_le32(US_BULK_CS_SIGN); ++ csw->Tag = fsg->tag; ++ csw->Residue = cpu_to_le32(fsg->residue); ++ csw->Status = status; ++ ++ bh->inreq->length = US_BULK_CS_WRAP_LEN; ++ bh->inreq->zero = 0; ++ start_transfer(fsg, fsg->bulk_in, bh->inreq, ++ &bh->inreq_busy, &bh->state); ++ ++ } else if (mod_data.transport_type == USB_PR_CB) { ++ ++ /* Control-Bulk transport has no status phase! */ ++ return 0; ++ ++ } else { // USB_PR_CBI ++ struct interrupt_data *buf = bh->buf; ++ ++ /* Store and send the Interrupt data. UFI sends the ASC ++ * and ASCQ bytes. Everything else sends a Type (which ++ * is always 0) and the status Value. */ ++ if (mod_data.protocol_type == USB_SC_UFI) { ++ buf->bType = ASC(sd); ++ buf->bValue = ASCQ(sd); ++ } else { ++ buf->bType = 0; ++ buf->bValue = status; ++ } ++ fsg->intreq->length = CBI_INTERRUPT_DATA_LEN; ++ ++ fsg->intr_buffhd = bh; // Point to the right buffhd ++ fsg->intreq->buf = bh->inreq->buf; ++ fsg->intreq->context = bh; ++ start_transfer(fsg, fsg->intr_in, fsg->intreq, ++ &fsg->intreq_busy, &bh->state); ++ } ++ ++ fsg->next_buffhd_to_fill = bh->next; ++ return 0; ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* Check whether the command is properly formed and whether its data size ++ * and direction agree with the values we already have. */ ++static int check_command(struct fsg_dev *fsg, int cmnd_size, ++ enum data_direction data_dir, unsigned int mask, ++ int needs_medium, const char *name) ++{ ++ int i; ++ int lun = fsg->cmnd[1] >> 5; ++ static const char dirletter[4] = {'u', 'o', 'i', 'n'}; ++ char hdlen[20]; ++ struct fsg_lun *curlun; ++ ++ /* Adjust the expected cmnd_size for protocol encapsulation padding. ++ * Transparent SCSI doesn't pad. */ ++ if (protocol_is_scsi()) ++ ; ++ ++ /* There's some disagreement as to whether RBC pads commands or not. ++ * We'll play it safe and accept either form. */ ++ else if (mod_data.protocol_type == USB_SC_RBC) { ++ if (fsg->cmnd_size == 12) ++ cmnd_size = 12; ++ ++ /* All the other protocols pad to 12 bytes */ ++ } else ++ cmnd_size = 12; ++ ++ hdlen[0] = 0; ++ if (fsg->data_dir != DATA_DIR_UNKNOWN) ++ sprintf(hdlen, ", H%c=%u", dirletter[(int) fsg->data_dir], ++ fsg->data_size); ++ VDBG(fsg, "SCSI command: %s; Dc=%d, D%c=%u; Hc=%d%s\n", ++ name, cmnd_size, dirletter[(int) data_dir], ++ fsg->data_size_from_cmnd, fsg->cmnd_size, hdlen); ++ ++ /* We can't reply at all until we know the correct data direction ++ * and size. */ ++ if (fsg->data_size_from_cmnd == 0) ++ data_dir = DATA_DIR_NONE; ++ if (fsg->data_dir == DATA_DIR_UNKNOWN) { // CB or CBI ++ fsg->data_dir = data_dir; ++ fsg->data_size = fsg->data_size_from_cmnd; ++ ++ } else { // Bulk-only ++ if (fsg->data_size < fsg->data_size_from_cmnd) { ++ ++ /* Host data size < Device data size is a phase error. ++ * Carry out the command, but only transfer as much ++ * as we are allowed. */ ++ fsg->data_size_from_cmnd = fsg->data_size; ++ fsg->phase_error = 1; ++ } ++ } ++ fsg->residue = fsg->usb_amount_left = fsg->data_size; ++ ++ /* Conflicting data directions is a phase error */ ++ if (fsg->data_dir != data_dir && fsg->data_size_from_cmnd > 0) { ++ fsg->phase_error = 1; ++ return -EINVAL; ++ } ++ ++ /* Verify the length of the command itself */ ++ if (cmnd_size != fsg->cmnd_size) { ++ ++ /* Special case workaround: There are plenty of buggy SCSI ++ * implementations. Many have issues with cbw->Length ++ * field passing a wrong command size. For those cases we ++ * always try to work around the problem by using the length ++ * sent by the host side provided it is at least as large ++ * as the correct command length. ++ * Examples of such cases would be MS-Windows, which issues ++ * REQUEST SENSE with cbw->Length == 12 where it should ++ * be 6, and xbox360 issuing INQUIRY, TEST UNIT READY and ++ * REQUEST SENSE with cbw->Length == 10 where it should ++ * be 6 as well. ++ */ ++ if (cmnd_size <= fsg->cmnd_size) { ++ DBG(fsg, "%s is buggy! Expected length %d " ++ "but we got %d\n", name, ++ cmnd_size, fsg->cmnd_size); ++ cmnd_size = fsg->cmnd_size; ++ } else { ++ fsg->phase_error = 1; ++ return -EINVAL; ++ } ++ } ++ ++ /* Check that the LUN values are consistent */ ++ if (transport_is_bbb()) { ++ if (fsg->lun != lun) ++ DBG(fsg, "using LUN %d from CBW, " ++ "not LUN %d from CDB\n", ++ fsg->lun, lun); ++ } ++ ++ /* Check the LUN */ ++ curlun = fsg->curlun; ++ if (curlun) { ++ if (fsg->cmnd[0] != REQUEST_SENSE) { ++ curlun->sense_data = SS_NO_SENSE; ++ curlun->sense_data_info = 0; ++ curlun->info_valid = 0; ++ } ++ } else { ++ fsg->bad_lun_okay = 0; ++ ++ /* INQUIRY and REQUEST SENSE commands are explicitly allowed ++ * to use unsupported LUNs; all others may not. */ ++ if (fsg->cmnd[0] != INQUIRY && ++ fsg->cmnd[0] != REQUEST_SENSE) { ++ DBG(fsg, "unsupported LUN %d\n", fsg->lun); ++ return -EINVAL; ++ } ++ } ++ ++ /* If a unit attention condition exists, only INQUIRY and ++ * REQUEST SENSE commands are allowed; anything else must fail. */ ++ if (curlun && curlun->unit_attention_data != SS_NO_SENSE && ++ fsg->cmnd[0] != INQUIRY && ++ fsg->cmnd[0] != REQUEST_SENSE) { ++ curlun->sense_data = curlun->unit_attention_data; ++ curlun->unit_attention_data = SS_NO_SENSE; ++ return -EINVAL; ++ } ++ ++ /* Check that only command bytes listed in the mask are non-zero */ ++ fsg->cmnd[1] &= 0x1f; // Mask away the LUN ++ for (i = 1; i < cmnd_size; ++i) { ++ if (fsg->cmnd[i] && !(mask & (1 << i))) { ++ if (curlun) ++ curlun->sense_data = SS_INVALID_FIELD_IN_CDB; ++ return -EINVAL; ++ } ++ } ++ ++ /* If the medium isn't mounted and the command needs to access ++ * it, return an error. */ ++ if (curlun && !fsg_lun_is_open(curlun) && needs_medium) { ++ curlun->sense_data = SS_MEDIUM_NOT_PRESENT; ++ return -EINVAL; ++ } ++ ++ return 0; ++} ++ ++/* wrapper of check_command for data size in blocks handling */ ++static int check_command_size_in_blocks(struct fsg_dev *fsg, int cmnd_size, ++ enum data_direction data_dir, unsigned int mask, ++ int needs_medium, const char *name) ++{ ++ if (fsg->curlun) ++ fsg->data_size_from_cmnd <<= fsg->curlun->blkbits; ++ return check_command(fsg, cmnd_size, data_dir, ++ mask, needs_medium, name); ++} ++ ++static int do_scsi_command(struct fsg_dev *fsg) ++{ ++ struct fsg_buffhd *bh; ++ int rc; ++ int reply = -EINVAL; ++ int i; ++ static char unknown[16]; ++ ++ dump_cdb(fsg); ++ ++ /* Wait for the next buffer to become available for data or status */ ++ bh = fsg->next_buffhd_to_drain = fsg->next_buffhd_to_fill; ++ while (bh->state != BUF_STATE_EMPTY) { ++ rc = sleep_thread(fsg); ++ if (rc) ++ return rc; ++ } ++ fsg->phase_error = 0; ++ fsg->short_packet_received = 0; ++ ++ down_read(&fsg->filesem); // We're using the backing file ++ switch (fsg->cmnd[0]) { ++ ++ case INQUIRY: ++ fsg->data_size_from_cmnd = fsg->cmnd[4]; ++ if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST, ++ (1<<4), 0, ++ "INQUIRY")) == 0) ++ reply = do_inquiry(fsg, bh); ++ break; ++ ++ case MODE_SELECT: ++ fsg->data_size_from_cmnd = fsg->cmnd[4]; ++ if ((reply = check_command(fsg, 6, DATA_DIR_FROM_HOST, ++ (1<<1) | (1<<4), 0, ++ "MODE SELECT(6)")) == 0) ++ reply = do_mode_select(fsg, bh); ++ break; ++ ++ case MODE_SELECT_10: ++ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]); ++ if ((reply = check_command(fsg, 10, DATA_DIR_FROM_HOST, ++ (1<<1) | (3<<7), 0, ++ "MODE SELECT(10)")) == 0) ++ reply = do_mode_select(fsg, bh); ++ break; ++ ++ case MODE_SENSE: ++ fsg->data_size_from_cmnd = fsg->cmnd[4]; ++ if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST, ++ (1<<1) | (1<<2) | (1<<4), 0, ++ "MODE SENSE(6)")) == 0) ++ reply = do_mode_sense(fsg, bh); ++ break; ++ ++ case MODE_SENSE_10: ++ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]); ++ if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST, ++ (1<<1) | (1<<2) | (3<<7), 0, ++ "MODE SENSE(10)")) == 0) ++ reply = do_mode_sense(fsg, bh); ++ break; ++ ++ case ALLOW_MEDIUM_REMOVAL: ++ fsg->data_size_from_cmnd = 0; ++ if ((reply = check_command(fsg, 6, DATA_DIR_NONE, ++ (1<<4), 0, ++ "PREVENT-ALLOW MEDIUM REMOVAL")) == 0) ++ reply = do_prevent_allow(fsg); ++ break; ++ ++ case READ_6: ++ i = fsg->cmnd[4]; ++ fsg->data_size_from_cmnd = (i == 0) ? 256 : i; ++ if ((reply = check_command_size_in_blocks(fsg, 6, ++ DATA_DIR_TO_HOST, ++ (7<<1) | (1<<4), 1, ++ "READ(6)")) == 0) ++ reply = do_read(fsg); ++ break; ++ ++ case READ_10: ++ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]); ++ if ((reply = check_command_size_in_blocks(fsg, 10, ++ DATA_DIR_TO_HOST, ++ (1<<1) | (0xf<<2) | (3<<7), 1, ++ "READ(10)")) == 0) ++ reply = do_read(fsg); ++ break; ++ ++ case READ_12: ++ fsg->data_size_from_cmnd = get_unaligned_be32(&fsg->cmnd[6]); ++ if ((reply = check_command_size_in_blocks(fsg, 12, ++ DATA_DIR_TO_HOST, ++ (1<<1) | (0xf<<2) | (0xf<<6), 1, ++ "READ(12)")) == 0) ++ reply = do_read(fsg); ++ break; ++ ++ case READ_CAPACITY: ++ fsg->data_size_from_cmnd = 8; ++ if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST, ++ (0xf<<2) | (1<<8), 1, ++ "READ CAPACITY")) == 0) ++ reply = do_read_capacity(fsg, bh); ++ break; ++ ++ case READ_HEADER: ++ if (!mod_data.cdrom) ++ goto unknown_cmnd; ++ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]); ++ if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST, ++ (3<<7) | (0x1f<<1), 1, ++ "READ HEADER")) == 0) ++ reply = do_read_header(fsg, bh); ++ break; ++ ++ case READ_TOC: ++ if (!mod_data.cdrom) ++ goto unknown_cmnd; ++ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]); ++ if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST, ++ (7<<6) | (1<<1), 1, ++ "READ TOC")) == 0) ++ reply = do_read_toc(fsg, bh); ++ break; ++ ++ case READ_FORMAT_CAPACITIES: ++ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]); ++ if ((reply = check_command(fsg, 10, DATA_DIR_TO_HOST, ++ (3<<7), 1, ++ "READ FORMAT CAPACITIES")) == 0) ++ reply = do_read_format_capacities(fsg, bh); ++ break; ++ ++ case REQUEST_SENSE: ++ fsg->data_size_from_cmnd = fsg->cmnd[4]; ++ if ((reply = check_command(fsg, 6, DATA_DIR_TO_HOST, ++ (1<<4), 0, ++ "REQUEST SENSE")) == 0) ++ reply = do_request_sense(fsg, bh); ++ break; ++ ++ case START_STOP: ++ fsg->data_size_from_cmnd = 0; ++ if ((reply = check_command(fsg, 6, DATA_DIR_NONE, ++ (1<<1) | (1<<4), 0, ++ "START-STOP UNIT")) == 0) ++ reply = do_start_stop(fsg); ++ break; ++ ++ case SYNCHRONIZE_CACHE: ++ fsg->data_size_from_cmnd = 0; ++ if ((reply = check_command(fsg, 10, DATA_DIR_NONE, ++ (0xf<<2) | (3<<7), 1, ++ "SYNCHRONIZE CACHE")) == 0) ++ reply = do_synchronize_cache(fsg); ++ break; ++ ++ case TEST_UNIT_READY: ++ fsg->data_size_from_cmnd = 0; ++ reply = check_command(fsg, 6, DATA_DIR_NONE, ++ 0, 1, ++ "TEST UNIT READY"); ++ break; ++ ++ /* Although optional, this command is used by MS-Windows. We ++ * support a minimal version: BytChk must be 0. */ ++ case VERIFY: ++ fsg->data_size_from_cmnd = 0; ++ if ((reply = check_command(fsg, 10, DATA_DIR_NONE, ++ (1<<1) | (0xf<<2) | (3<<7), 1, ++ "VERIFY")) == 0) ++ reply = do_verify(fsg); ++ break; ++ ++ case WRITE_6: ++ i = fsg->cmnd[4]; ++ fsg->data_size_from_cmnd = (i == 0) ? 256 : i; ++ if ((reply = check_command_size_in_blocks(fsg, 6, ++ DATA_DIR_FROM_HOST, ++ (7<<1) | (1<<4), 1, ++ "WRITE(6)")) == 0) ++ reply = do_write(fsg); ++ break; ++ ++ case WRITE_10: ++ fsg->data_size_from_cmnd = get_unaligned_be16(&fsg->cmnd[7]); ++ if ((reply = check_command_size_in_blocks(fsg, 10, ++ DATA_DIR_FROM_HOST, ++ (1<<1) | (0xf<<2) | (3<<7), 1, ++ "WRITE(10)")) == 0) ++ reply = do_write(fsg); ++ break; ++ ++ case WRITE_12: ++ fsg->data_size_from_cmnd = get_unaligned_be32(&fsg->cmnd[6]); ++ if ((reply = check_command_size_in_blocks(fsg, 12, ++ DATA_DIR_FROM_HOST, ++ (1<<1) | (0xf<<2) | (0xf<<6), 1, ++ "WRITE(12)")) == 0) ++ reply = do_write(fsg); ++ break; ++ ++ /* Some mandatory commands that we recognize but don't implement. ++ * They don't mean much in this setting. It's left as an exercise ++ * for anyone interested to implement RESERVE and RELEASE in terms ++ * of Posix locks. */ ++ case FORMAT_UNIT: ++ case RELEASE: ++ case RESERVE: ++ case SEND_DIAGNOSTIC: ++ // Fall through ++ ++ default: ++ unknown_cmnd: ++ fsg->data_size_from_cmnd = 0; ++ sprintf(unknown, "Unknown x%02x", fsg->cmnd[0]); ++ if ((reply = check_command(fsg, fsg->cmnd_size, ++ DATA_DIR_UNKNOWN, ~0, 0, unknown)) == 0) { ++ fsg->curlun->sense_data = SS_INVALID_COMMAND; ++ reply = -EINVAL; ++ } ++ break; ++ } ++ up_read(&fsg->filesem); ++ ++ if (reply == -EINTR || signal_pending(current)) ++ return -EINTR; ++ ++ /* Set up the single reply buffer for finish_reply() */ ++ if (reply == -EINVAL) ++ reply = 0; // Error reply length ++ if (reply >= 0 && fsg->data_dir == DATA_DIR_TO_HOST) { ++ reply = min((u32) reply, fsg->data_size_from_cmnd); ++ bh->inreq->length = reply; ++ bh->state = BUF_STATE_FULL; ++ fsg->residue -= reply; ++ } // Otherwise it's already set ++ ++ return 0; ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static int received_cbw(struct fsg_dev *fsg, struct fsg_buffhd *bh) ++{ ++ struct usb_request *req = bh->outreq; ++ struct bulk_cb_wrap *cbw = req->buf; ++ ++ /* Was this a real packet? Should it be ignored? */ ++ if (req->status || test_bit(IGNORE_BULK_OUT, &fsg->atomic_bitflags)) ++ return -EINVAL; ++ ++ /* Is the CBW valid? */ ++ if (req->actual != US_BULK_CB_WRAP_LEN || ++ cbw->Signature != cpu_to_le32( ++ US_BULK_CB_SIGN)) { ++ DBG(fsg, "invalid CBW: len %u sig 0x%x\n", ++ req->actual, ++ le32_to_cpu(cbw->Signature)); ++ ++ /* The Bulk-only spec says we MUST stall the IN endpoint ++ * (6.6.1), so it's unavoidable. It also says we must ++ * retain this state until the next reset, but there's ++ * no way to tell the controller driver it should ignore ++ * Clear-Feature(HALT) requests. ++ * ++ * We aren't required to halt the OUT endpoint; instead ++ * we can simply accept and discard any data received ++ * until the next reset. */ ++ wedge_bulk_in_endpoint(fsg); ++ set_bit(IGNORE_BULK_OUT, &fsg->atomic_bitflags); ++ return -EINVAL; ++ } ++ ++ /* Is the CBW meaningful? */ ++ if (cbw->Lun >= FSG_MAX_LUNS || cbw->Flags & ~US_BULK_FLAG_IN || ++ cbw->Length <= 0 || cbw->Length > MAX_COMMAND_SIZE) { ++ DBG(fsg, "non-meaningful CBW: lun = %u, flags = 0x%x, " ++ "cmdlen %u\n", ++ cbw->Lun, cbw->Flags, cbw->Length); ++ ++ /* We can do anything we want here, so let's stall the ++ * bulk pipes if we are allowed to. */ ++ if (mod_data.can_stall) { ++ fsg_set_halt(fsg, fsg->bulk_out); ++ halt_bulk_in_endpoint(fsg); ++ } ++ return -EINVAL; ++ } ++ ++ /* Save the command for later */ ++ fsg->cmnd_size = cbw->Length; ++ memcpy(fsg->cmnd, cbw->CDB, fsg->cmnd_size); ++ if (cbw->Flags & US_BULK_FLAG_IN) ++ fsg->data_dir = DATA_DIR_TO_HOST; ++ else ++ fsg->data_dir = DATA_DIR_FROM_HOST; ++ fsg->data_size = le32_to_cpu(cbw->DataTransferLength); ++ if (fsg->data_size == 0) ++ fsg->data_dir = DATA_DIR_NONE; ++ fsg->lun = cbw->Lun; ++ fsg->tag = cbw->Tag; ++ return 0; ++} ++ ++ ++static int get_next_command(struct fsg_dev *fsg) ++{ ++ struct fsg_buffhd *bh; ++ int rc = 0; ++ ++ if (transport_is_bbb()) { ++ ++ /* Wait for the next buffer to become available */ ++ bh = fsg->next_buffhd_to_fill; ++ while (bh->state != BUF_STATE_EMPTY) { ++ rc = sleep_thread(fsg); ++ if (rc) ++ return rc; ++ } ++ ++ /* Queue a request to read a Bulk-only CBW */ ++ set_bulk_out_req_length(fsg, bh, US_BULK_CB_WRAP_LEN); ++ start_transfer(fsg, fsg->bulk_out, bh->outreq, ++ &bh->outreq_busy, &bh->state); ++ ++ /* We will drain the buffer in software, which means we ++ * can reuse it for the next filling. No need to advance ++ * next_buffhd_to_fill. */ ++ ++ /* Wait for the CBW to arrive */ ++ while (bh->state != BUF_STATE_FULL) { ++ rc = sleep_thread(fsg); ++ if (rc) ++ return rc; ++ } ++ smp_rmb(); ++ rc = received_cbw(fsg, bh); ++ bh->state = BUF_STATE_EMPTY; ++ ++ } else { // USB_PR_CB or USB_PR_CBI ++ ++ /* Wait for the next command to arrive */ ++ while (fsg->cbbuf_cmnd_size == 0) { ++ rc = sleep_thread(fsg); ++ if (rc) ++ return rc; ++ } ++ ++ /* Is the previous status interrupt request still busy? ++ * The host is allowed to skip reading the status, ++ * so we must cancel it. */ ++ if (fsg->intreq_busy) ++ usb_ep_dequeue(fsg->intr_in, fsg->intreq); ++ ++ /* Copy the command and mark the buffer empty */ ++ fsg->data_dir = DATA_DIR_UNKNOWN; ++ spin_lock_irq(&fsg->lock); ++ fsg->cmnd_size = fsg->cbbuf_cmnd_size; ++ memcpy(fsg->cmnd, fsg->cbbuf_cmnd, fsg->cmnd_size); ++ fsg->cbbuf_cmnd_size = 0; ++ spin_unlock_irq(&fsg->lock); ++ ++ /* Use LUN from the command */ ++ fsg->lun = fsg->cmnd[1] >> 5; ++ } ++ ++ /* Update current lun */ ++ if (fsg->lun >= 0 && fsg->lun < fsg->nluns) ++ fsg->curlun = &fsg->luns[fsg->lun]; ++ else ++ fsg->curlun = NULL; ++ ++ return rc; ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static int enable_endpoint(struct fsg_dev *fsg, struct usb_ep *ep, ++ const struct usb_endpoint_descriptor *d) ++{ ++ int rc; ++ ++ ep->driver_data = fsg; ++ ep->desc = d; ++ rc = usb_ep_enable(ep); ++ if (rc) ++ ERROR(fsg, "can't enable %s, result %d\n", ep->name, rc); ++ return rc; ++} ++ ++static int alloc_request(struct fsg_dev *fsg, struct usb_ep *ep, ++ struct usb_request **preq) ++{ ++ *preq = usb_ep_alloc_request(ep, GFP_ATOMIC); ++ if (*preq) ++ return 0; ++ ERROR(fsg, "can't allocate request for %s\n", ep->name); ++ return -ENOMEM; ++} ++ ++/* ++ * Reset interface setting and re-init endpoint state (toggle etc). ++ * Call with altsetting < 0 to disable the interface. The only other ++ * available altsetting is 0, which enables the interface. ++ */ ++static int do_set_interface(struct fsg_dev *fsg, int altsetting) ++{ ++ int rc = 0; ++ int i; ++ const struct usb_endpoint_descriptor *d; ++ ++ if (fsg->running) ++ DBG(fsg, "reset interface\n"); ++ ++reset: ++ /* Deallocate the requests */ ++ for (i = 0; i < fsg_num_buffers; ++i) { ++ struct fsg_buffhd *bh = &fsg->buffhds[i]; ++ ++ if (bh->inreq) { ++ usb_ep_free_request(fsg->bulk_in, bh->inreq); ++ bh->inreq = NULL; ++ } ++ if (bh->outreq) { ++ usb_ep_free_request(fsg->bulk_out, bh->outreq); ++ bh->outreq = NULL; ++ } ++ } ++ if (fsg->intreq) { ++ usb_ep_free_request(fsg->intr_in, fsg->intreq); ++ fsg->intreq = NULL; ++ } ++ ++ /* Disable the endpoints */ ++ if (fsg->bulk_in_enabled) { ++ usb_ep_disable(fsg->bulk_in); ++ fsg->bulk_in_enabled = 0; ++ } ++ if (fsg->bulk_out_enabled) { ++ usb_ep_disable(fsg->bulk_out); ++ fsg->bulk_out_enabled = 0; ++ } ++ if (fsg->intr_in_enabled) { ++ usb_ep_disable(fsg->intr_in); ++ fsg->intr_in_enabled = 0; ++ } ++ ++ fsg->running = 0; ++ if (altsetting < 0 || rc != 0) ++ return rc; ++ ++ DBG(fsg, "set interface %d\n", altsetting); ++ ++ /* Enable the endpoints */ ++ d = fsg_ep_desc(fsg->gadget, ++ &fsg_fs_bulk_in_desc, &fsg_hs_bulk_in_desc, ++ &fsg_ss_bulk_in_desc); ++ if ((rc = enable_endpoint(fsg, fsg->bulk_in, d)) != 0) ++ goto reset; ++ fsg->bulk_in_enabled = 1; ++ ++ d = fsg_ep_desc(fsg->gadget, ++ &fsg_fs_bulk_out_desc, &fsg_hs_bulk_out_desc, ++ &fsg_ss_bulk_out_desc); ++ if ((rc = enable_endpoint(fsg, fsg->bulk_out, d)) != 0) ++ goto reset; ++ fsg->bulk_out_enabled = 1; ++ fsg->bulk_out_maxpacket = usb_endpoint_maxp(d); ++ clear_bit(IGNORE_BULK_OUT, &fsg->atomic_bitflags); ++ ++ if (transport_is_cbi()) { ++ d = fsg_ep_desc(fsg->gadget, ++ &fsg_fs_intr_in_desc, &fsg_hs_intr_in_desc, ++ &fsg_ss_intr_in_desc); ++ if ((rc = enable_endpoint(fsg, fsg->intr_in, d)) != 0) ++ goto reset; ++ fsg->intr_in_enabled = 1; ++ } ++ ++ /* Allocate the requests */ ++ for (i = 0; i < fsg_num_buffers; ++i) { ++ struct fsg_buffhd *bh = &fsg->buffhds[i]; ++ ++ if ((rc = alloc_request(fsg, fsg->bulk_in, &bh->inreq)) != 0) ++ goto reset; ++ if ((rc = alloc_request(fsg, fsg->bulk_out, &bh->outreq)) != 0) ++ goto reset; ++ bh->inreq->buf = bh->outreq->buf = bh->buf; ++ bh->inreq->context = bh->outreq->context = bh; ++ bh->inreq->complete = bulk_in_complete; ++ bh->outreq->complete = bulk_out_complete; ++ } ++ if (transport_is_cbi()) { ++ if ((rc = alloc_request(fsg, fsg->intr_in, &fsg->intreq)) != 0) ++ goto reset; ++ fsg->intreq->complete = intr_in_complete; ++ } ++ ++ fsg->running = 1; ++ for (i = 0; i < fsg->nluns; ++i) ++ fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED; ++ return rc; ++} ++ ++ ++/* ++ * Change our operational configuration. This code must agree with the code ++ * that returns config descriptors, and with interface altsetting code. ++ * ++ * It's also responsible for power management interactions. Some ++ * configurations might not work with our current power sources. ++ * For now we just assume the gadget is always self-powered. ++ */ ++static int do_set_config(struct fsg_dev *fsg, u8 new_config) ++{ ++ int rc = 0; ++ ++ /* Disable the single interface */ ++ if (fsg->config != 0) { ++ DBG(fsg, "reset config\n"); ++ fsg->config = 0; ++ rc = do_set_interface(fsg, -1); ++ } ++ ++ /* Enable the interface */ ++ if (new_config != 0) { ++ fsg->config = new_config; ++ if ((rc = do_set_interface(fsg, 0)) != 0) ++ fsg->config = 0; // Reset on errors ++ else ++ INFO(fsg, "%s config #%d\n", ++ usb_speed_string(fsg->gadget->speed), ++ fsg->config); ++ } ++ return rc; ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static void handle_exception(struct fsg_dev *fsg) ++{ ++ siginfo_t info; ++ int sig; ++ int i; ++ int num_active; ++ struct fsg_buffhd *bh; ++ enum fsg_state old_state; ++ u8 new_config; ++ struct fsg_lun *curlun; ++ unsigned int exception_req_tag; ++ int rc; ++ ++ /* Clear the existing signals. Anything but SIGUSR1 is converted ++ * into a high-priority EXIT exception. */ ++ for (;;) { ++ sig = dequeue_signal_lock(current, ¤t->blocked, &info); ++ if (!sig) ++ break; ++ if (sig != SIGUSR1) { ++ if (fsg->state < FSG_STATE_EXIT) ++ DBG(fsg, "Main thread exiting on signal\n"); ++ raise_exception(fsg, FSG_STATE_EXIT); ++ } ++ } ++ ++ /* Cancel all the pending transfers */ ++ if (fsg->intreq_busy) ++ usb_ep_dequeue(fsg->intr_in, fsg->intreq); ++ for (i = 0; i < fsg_num_buffers; ++i) { ++ bh = &fsg->buffhds[i]; ++ if (bh->inreq_busy) ++ usb_ep_dequeue(fsg->bulk_in, bh->inreq); ++ if (bh->outreq_busy) ++ usb_ep_dequeue(fsg->bulk_out, bh->outreq); ++ } ++ ++ /* Wait until everything is idle */ ++ for (;;) { ++ num_active = fsg->intreq_busy; ++ for (i = 0; i < fsg_num_buffers; ++i) { ++ bh = &fsg->buffhds[i]; ++ num_active += bh->inreq_busy + bh->outreq_busy; ++ } ++ if (num_active == 0) ++ break; ++ if (sleep_thread(fsg)) ++ return; ++ } ++ ++ /* Clear out the controller's fifos */ ++ if (fsg->bulk_in_enabled) ++ usb_ep_fifo_flush(fsg->bulk_in); ++ if (fsg->bulk_out_enabled) ++ usb_ep_fifo_flush(fsg->bulk_out); ++ if (fsg->intr_in_enabled) ++ usb_ep_fifo_flush(fsg->intr_in); ++ ++ /* Reset the I/O buffer states and pointers, the SCSI ++ * state, and the exception. Then invoke the handler. */ ++ spin_lock_irq(&fsg->lock); ++ ++ for (i = 0; i < fsg_num_buffers; ++i) { ++ bh = &fsg->buffhds[i]; ++ bh->state = BUF_STATE_EMPTY; ++ } ++ fsg->next_buffhd_to_fill = fsg->next_buffhd_to_drain = ++ &fsg->buffhds[0]; ++ ++ exception_req_tag = fsg->exception_req_tag; ++ new_config = fsg->new_config; ++ old_state = fsg->state; ++ ++ if (old_state == FSG_STATE_ABORT_BULK_OUT) ++ fsg->state = FSG_STATE_STATUS_PHASE; ++ else { ++ for (i = 0; i < fsg->nluns; ++i) { ++ curlun = &fsg->luns[i]; ++ curlun->prevent_medium_removal = 0; ++ curlun->sense_data = curlun->unit_attention_data = ++ SS_NO_SENSE; ++ curlun->sense_data_info = 0; ++ curlun->info_valid = 0; ++ } ++ fsg->state = FSG_STATE_IDLE; ++ } ++ spin_unlock_irq(&fsg->lock); ++ ++ /* Carry out any extra actions required for the exception */ ++ switch (old_state) { ++ default: ++ break; ++ ++ case FSG_STATE_ABORT_BULK_OUT: ++ send_status(fsg); ++ spin_lock_irq(&fsg->lock); ++ if (fsg->state == FSG_STATE_STATUS_PHASE) ++ fsg->state = FSG_STATE_IDLE; ++ spin_unlock_irq(&fsg->lock); ++ break; ++ ++ case FSG_STATE_RESET: ++ /* In case we were forced against our will to halt a ++ * bulk endpoint, clear the halt now. (The SuperH UDC ++ * requires this.) */ ++ if (test_and_clear_bit(IGNORE_BULK_OUT, &fsg->atomic_bitflags)) ++ usb_ep_clear_halt(fsg->bulk_in); ++ ++ if (transport_is_bbb()) { ++ if (fsg->ep0_req_tag == exception_req_tag) ++ ep0_queue(fsg); // Complete the status stage ++ ++ } else if (transport_is_cbi()) ++ send_status(fsg); // Status by interrupt pipe ++ ++ /* Technically this should go here, but it would only be ++ * a waste of time. Ditto for the INTERFACE_CHANGE and ++ * CONFIG_CHANGE cases. */ ++ // for (i = 0; i < fsg->nluns; ++i) ++ // fsg->luns[i].unit_attention_data = SS_RESET_OCCURRED; ++ break; ++ ++ case FSG_STATE_INTERFACE_CHANGE: ++ rc = do_set_interface(fsg, 0); ++ if (fsg->ep0_req_tag != exception_req_tag) ++ break; ++ if (rc != 0) // STALL on errors ++ fsg_set_halt(fsg, fsg->ep0); ++ else // Complete the status stage ++ ep0_queue(fsg); ++ break; ++ ++ case FSG_STATE_CONFIG_CHANGE: ++ rc = do_set_config(fsg, new_config); ++ if (fsg->ep0_req_tag != exception_req_tag) ++ break; ++ if (rc != 0) // STALL on errors ++ fsg_set_halt(fsg, fsg->ep0); ++ else // Complete the status stage ++ ep0_queue(fsg); ++ break; ++ ++ case FSG_STATE_DISCONNECT: ++ for (i = 0; i < fsg->nluns; ++i) ++ fsg_lun_fsync_sub(fsg->luns + i); ++ do_set_config(fsg, 0); // Unconfigured state ++ break; ++ ++ case FSG_STATE_EXIT: ++ case FSG_STATE_TERMINATED: ++ do_set_config(fsg, 0); // Free resources ++ spin_lock_irq(&fsg->lock); ++ fsg->state = FSG_STATE_TERMINATED; // Stop the thread ++ spin_unlock_irq(&fsg->lock); ++ break; ++ } ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static int fsg_main_thread(void *fsg_) ++{ ++ struct fsg_dev *fsg = fsg_; ++ ++ /* Allow the thread to be killed by a signal, but set the signal mask ++ * to block everything but INT, TERM, KILL, and USR1. */ ++ allow_signal(SIGINT); ++ allow_signal(SIGTERM); ++ allow_signal(SIGKILL); ++ allow_signal(SIGUSR1); ++ ++ /* Allow the thread to be frozen */ ++ set_freezable(); ++ ++ /* Arrange for userspace references to be interpreted as kernel ++ * pointers. That way we can pass a kernel pointer to a routine ++ * that expects a __user pointer and it will work okay. */ ++ set_fs(get_ds()); ++ ++ /* The main loop */ ++ while (fsg->state != FSG_STATE_TERMINATED) { ++ if (exception_in_progress(fsg) || signal_pending(current)) { ++ handle_exception(fsg); ++ continue; ++ } ++ ++ if (!fsg->running) { ++ sleep_thread(fsg); ++ continue; ++ } ++ ++ if (get_next_command(fsg)) ++ continue; ++ ++ spin_lock_irq(&fsg->lock); ++ if (!exception_in_progress(fsg)) ++ fsg->state = FSG_STATE_DATA_PHASE; ++ spin_unlock_irq(&fsg->lock); ++ ++ if (do_scsi_command(fsg) || finish_reply(fsg)) ++ continue; ++ ++ spin_lock_irq(&fsg->lock); ++ if (!exception_in_progress(fsg)) ++ fsg->state = FSG_STATE_STATUS_PHASE; ++ spin_unlock_irq(&fsg->lock); ++ ++ if (send_status(fsg)) ++ continue; ++ ++ spin_lock_irq(&fsg->lock); ++ if (!exception_in_progress(fsg)) ++ fsg->state = FSG_STATE_IDLE; ++ spin_unlock_irq(&fsg->lock); ++ } ++ ++ spin_lock_irq(&fsg->lock); ++ fsg->thread_task = NULL; ++ spin_unlock_irq(&fsg->lock); ++ ++ /* If we are exiting because of a signal, unregister the ++ * gadget driver. */ ++ if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags)) ++ usb_gadget_unregister_driver(&fsg_driver); ++ ++ /* Let the unbind and cleanup routines know the thread has exited */ ++ complete_and_exit(&fsg->thread_notifier, 0); ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++ ++/* The write permissions and store_xxx pointers are set in fsg_bind() */ ++static DEVICE_ATTR(ro, 0444, fsg_show_ro, NULL); ++static DEVICE_ATTR(nofua, 0644, fsg_show_nofua, NULL); ++static DEVICE_ATTR(file, 0444, fsg_show_file, NULL); ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static void fsg_release(struct kref *ref) ++{ ++ struct fsg_dev *fsg = container_of(ref, struct fsg_dev, ref); ++ ++ kfree(fsg->luns); ++ kfree(fsg); ++} ++ ++static void lun_release(struct device *dev) ++{ ++ struct rw_semaphore *filesem = dev_get_drvdata(dev); ++ struct fsg_dev *fsg = ++ container_of(filesem, struct fsg_dev, filesem); ++ ++ kref_put(&fsg->ref, fsg_release); ++} ++ ++static void /* __init_or_exit */ fsg_unbind(struct usb_gadget *gadget) ++{ ++ struct fsg_dev *fsg = get_gadget_data(gadget); ++ int i; ++ struct fsg_lun *curlun; ++ struct usb_request *req = fsg->ep0req; ++ ++ DBG(fsg, "unbind\n"); ++ clear_bit(REGISTERED, &fsg->atomic_bitflags); ++ ++ /* If the thread isn't already dead, tell it to exit now */ ++ if (fsg->state != FSG_STATE_TERMINATED) { ++ raise_exception(fsg, FSG_STATE_EXIT); ++ wait_for_completion(&fsg->thread_notifier); ++ ++ /* The cleanup routine waits for this completion also */ ++ complete(&fsg->thread_notifier); ++ } ++ ++ /* Unregister the sysfs attribute files and the LUNs */ ++ for (i = 0; i < fsg->nluns; ++i) { ++ curlun = &fsg->luns[i]; ++ if (curlun->registered) { ++ device_remove_file(&curlun->dev, &dev_attr_nofua); ++ device_remove_file(&curlun->dev, &dev_attr_ro); ++ device_remove_file(&curlun->dev, &dev_attr_file); ++ fsg_lun_close(curlun); ++ device_unregister(&curlun->dev); ++ curlun->registered = 0; ++ } ++ } ++ ++ /* Free the data buffers */ ++ for (i = 0; i < fsg_num_buffers; ++i) ++ kfree(fsg->buffhds[i].buf); ++ ++ /* Free the request and buffer for endpoint 0 */ ++ if (req) { ++ kfree(req->buf); ++ usb_ep_free_request(fsg->ep0, req); ++ } ++ ++ set_gadget_data(gadget, NULL); ++} ++ ++ ++static int __init check_parameters(struct fsg_dev *fsg) ++{ ++ int prot; ++ int gcnum; ++ ++ /* Store the default values */ ++ mod_data.transport_type = USB_PR_BULK; ++ mod_data.transport_name = "Bulk-only"; ++ mod_data.protocol_type = USB_SC_SCSI; ++ mod_data.protocol_name = "Transparent SCSI"; ++ ++ /* Some peripheral controllers are known not to be able to ++ * halt bulk endpoints correctly. If one of them is present, ++ * disable stalls. ++ */ ++ if (gadget_is_at91(fsg->gadget)) ++ mod_data.can_stall = 0; ++ ++ if (mod_data.release == 0xffff) { // Parameter wasn't set ++ gcnum = usb_gadget_controller_number(fsg->gadget); ++ if (gcnum >= 0) ++ mod_data.release = 0x0300 + gcnum; ++ else { ++ WARNING(fsg, "controller '%s' not recognized\n", ++ fsg->gadget->name); ++ mod_data.release = 0x0399; ++ } ++ } ++ ++ prot = simple_strtol(mod_data.protocol_parm, NULL, 0); ++ ++#ifdef CONFIG_USB_FILE_STORAGE_TEST ++ if (strnicmp(mod_data.transport_parm, "BBB", 10) == 0) { ++ ; // Use default setting ++ } else if (strnicmp(mod_data.transport_parm, "CB", 10) == 0) { ++ mod_data.transport_type = USB_PR_CB; ++ mod_data.transport_name = "Control-Bulk"; ++ } else if (strnicmp(mod_data.transport_parm, "CBI", 10) == 0) { ++ mod_data.transport_type = USB_PR_CBI; ++ mod_data.transport_name = "Control-Bulk-Interrupt"; ++ } else { ++ ERROR(fsg, "invalid transport: %s\n", mod_data.transport_parm); ++ return -EINVAL; ++ } ++ ++ if (strnicmp(mod_data.protocol_parm, "SCSI", 10) == 0 || ++ prot == USB_SC_SCSI) { ++ ; // Use default setting ++ } else if (strnicmp(mod_data.protocol_parm, "RBC", 10) == 0 || ++ prot == USB_SC_RBC) { ++ mod_data.protocol_type = USB_SC_RBC; ++ mod_data.protocol_name = "RBC"; ++ } else if (strnicmp(mod_data.protocol_parm, "8020", 4) == 0 || ++ strnicmp(mod_data.protocol_parm, "ATAPI", 10) == 0 || ++ prot == USB_SC_8020) { ++ mod_data.protocol_type = USB_SC_8020; ++ mod_data.protocol_name = "8020i (ATAPI)"; ++ } else if (strnicmp(mod_data.protocol_parm, "QIC", 3) == 0 || ++ prot == USB_SC_QIC) { ++ mod_data.protocol_type = USB_SC_QIC; ++ mod_data.protocol_name = "QIC-157"; ++ } else if (strnicmp(mod_data.protocol_parm, "UFI", 10) == 0 || ++ prot == USB_SC_UFI) { ++ mod_data.protocol_type = USB_SC_UFI; ++ mod_data.protocol_name = "UFI"; ++ } else if (strnicmp(mod_data.protocol_parm, "8070", 4) == 0 || ++ prot == USB_SC_8070) { ++ mod_data.protocol_type = USB_SC_8070; ++ mod_data.protocol_name = "8070i"; ++ } else { ++ ERROR(fsg, "invalid protocol: %s\n", mod_data.protocol_parm); ++ return -EINVAL; ++ } ++ ++ mod_data.buflen &= PAGE_CACHE_MASK; ++ if (mod_data.buflen <= 0) { ++ ERROR(fsg, "invalid buflen\n"); ++ return -ETOOSMALL; ++ } ++ ++#endif /* CONFIG_USB_FILE_STORAGE_TEST */ ++ ++ /* Serial string handling. ++ * On a real device, the serial string would be loaded ++ * from permanent storage. */ ++ if (mod_data.serial) { ++ const char *ch; ++ unsigned len = 0; ++ ++ /* Sanity check : ++ * The CB[I] specification limits the serial string to ++ * 12 uppercase hexadecimal characters. ++ * BBB need at least 12 uppercase hexadecimal characters, ++ * with a maximum of 126. */ ++ for (ch = mod_data.serial; *ch; ++ch) { ++ ++len; ++ if ((*ch < '0' || *ch > '9') && ++ (*ch < 'A' || *ch > 'F')) { /* not uppercase hex */ ++ WARNING(fsg, ++ "Invalid serial string character: %c\n", ++ *ch); ++ goto no_serial; ++ } ++ } ++ if (len > 126 || ++ (mod_data.transport_type == USB_PR_BULK && len < 12) || ++ (mod_data.transport_type != USB_PR_BULK && len > 12)) { ++ WARNING(fsg, "Invalid serial string length!\n"); ++ goto no_serial; ++ } ++ fsg_strings[FSG_STRING_SERIAL - 1].s = mod_data.serial; ++ } else { ++ WARNING(fsg, "No serial-number string provided!\n"); ++ no_serial: ++ device_desc.iSerialNumber = 0; ++ } ++ ++ return 0; ++} ++ ++ ++static int __init fsg_bind(struct usb_gadget *gadget) ++{ ++ struct fsg_dev *fsg = the_fsg; ++ int rc; ++ int i; ++ struct fsg_lun *curlun; ++ struct usb_ep *ep; ++ struct usb_request *req; ++ char *pathbuf, *p; ++ ++ fsg->gadget = gadget; ++ set_gadget_data(gadget, fsg); ++ fsg->ep0 = gadget->ep0; ++ fsg->ep0->driver_data = fsg; ++ ++ if ((rc = check_parameters(fsg)) != 0) ++ goto out; ++ ++ if (mod_data.removable) { // Enable the store_xxx attributes ++ dev_attr_file.attr.mode = 0644; ++ dev_attr_file.store = fsg_store_file; ++ if (!mod_data.cdrom) { ++ dev_attr_ro.attr.mode = 0644; ++ dev_attr_ro.store = fsg_store_ro; ++ } ++ } ++ ++ /* Only for removable media? */ ++ dev_attr_nofua.attr.mode = 0644; ++ dev_attr_nofua.store = fsg_store_nofua; ++ ++ /* Find out how many LUNs there should be */ ++ i = mod_data.nluns; ++ if (i == 0) ++ i = max(mod_data.num_filenames, 1u); ++ if (i > FSG_MAX_LUNS) { ++ ERROR(fsg, "invalid number of LUNs: %d\n", i); ++ rc = -EINVAL; ++ goto out; ++ } ++ ++ /* Create the LUNs, open their backing files, and register the ++ * LUN devices in sysfs. */ ++ fsg->luns = kzalloc(i * sizeof(struct fsg_lun), GFP_KERNEL); ++ if (!fsg->luns) { ++ rc = -ENOMEM; ++ goto out; ++ } ++ fsg->nluns = i; ++ ++ for (i = 0; i < fsg->nluns; ++i) { ++ curlun = &fsg->luns[i]; ++ curlun->cdrom = !!mod_data.cdrom; ++ curlun->ro = mod_data.cdrom || mod_data.ro[i]; ++ curlun->initially_ro = curlun->ro; ++ curlun->removable = mod_data.removable; ++ curlun->nofua = mod_data.nofua[i]; ++ curlun->dev.release = lun_release; ++ curlun->dev.parent = &gadget->dev; ++ curlun->dev.driver = &fsg_driver.driver; ++ dev_set_drvdata(&curlun->dev, &fsg->filesem); ++ dev_set_name(&curlun->dev,"%s-lun%d", ++ dev_name(&gadget->dev), i); ++ ++ kref_get(&fsg->ref); ++ rc = device_register(&curlun->dev); ++ if (rc) { ++ INFO(fsg, "failed to register LUN%d: %d\n", i, rc); ++ put_device(&curlun->dev); ++ goto out; ++ } ++ curlun->registered = 1; ++ ++ rc = device_create_file(&curlun->dev, &dev_attr_ro); ++ if (rc) ++ goto out; ++ rc = device_create_file(&curlun->dev, &dev_attr_nofua); ++ if (rc) ++ goto out; ++ rc = device_create_file(&curlun->dev, &dev_attr_file); ++ if (rc) ++ goto out; ++ ++ if (mod_data.file[i] && *mod_data.file[i]) { ++ rc = fsg_lun_open(curlun, mod_data.file[i]); ++ if (rc) ++ goto out; ++ } else if (!mod_data.removable) { ++ ERROR(fsg, "no file given for LUN%d\n", i); ++ rc = -EINVAL; ++ goto out; ++ } ++ } ++ ++ /* Find all the endpoints we will use */ ++ usb_ep_autoconfig_reset(gadget); ++ ep = usb_ep_autoconfig(gadget, &fsg_fs_bulk_in_desc); ++ if (!ep) ++ goto autoconf_fail; ++ ep->driver_data = fsg; // claim the endpoint ++ fsg->bulk_in = ep; ++ ++ ep = usb_ep_autoconfig(gadget, &fsg_fs_bulk_out_desc); ++ if (!ep) ++ goto autoconf_fail; ++ ep->driver_data = fsg; // claim the endpoint ++ fsg->bulk_out = ep; ++ ++ if (transport_is_cbi()) { ++ ep = usb_ep_autoconfig(gadget, &fsg_fs_intr_in_desc); ++ if (!ep) ++ goto autoconf_fail; ++ ep->driver_data = fsg; // claim the endpoint ++ fsg->intr_in = ep; ++ } ++ ++ /* Fix up the descriptors */ ++ device_desc.idVendor = cpu_to_le16(mod_data.vendor); ++ device_desc.idProduct = cpu_to_le16(mod_data.product); ++ device_desc.bcdDevice = cpu_to_le16(mod_data.release); ++ ++ i = (transport_is_cbi() ? 3 : 2); // Number of endpoints ++ fsg_intf_desc.bNumEndpoints = i; ++ fsg_intf_desc.bInterfaceSubClass = mod_data.protocol_type; ++ fsg_intf_desc.bInterfaceProtocol = mod_data.transport_type; ++ fsg_fs_function[i + FSG_FS_FUNCTION_PRE_EP_ENTRIES] = NULL; ++ ++ if (gadget_is_dualspeed(gadget)) { ++ fsg_hs_function[i + FSG_HS_FUNCTION_PRE_EP_ENTRIES] = NULL; ++ ++ /* Assume endpoint addresses are the same for both speeds */ ++ fsg_hs_bulk_in_desc.bEndpointAddress = ++ fsg_fs_bulk_in_desc.bEndpointAddress; ++ fsg_hs_bulk_out_desc.bEndpointAddress = ++ fsg_fs_bulk_out_desc.bEndpointAddress; ++ fsg_hs_intr_in_desc.bEndpointAddress = ++ fsg_fs_intr_in_desc.bEndpointAddress; ++ } ++ ++ if (gadget_is_superspeed(gadget)) { ++ unsigned max_burst; ++ ++ fsg_ss_function[i + FSG_SS_FUNCTION_PRE_EP_ENTRIES] = NULL; ++ ++ /* Calculate bMaxBurst, we know packet size is 1024 */ ++ max_burst = min_t(unsigned, mod_data.buflen / 1024, 15); ++ ++ /* Assume endpoint addresses are the same for both speeds */ ++ fsg_ss_bulk_in_desc.bEndpointAddress = ++ fsg_fs_bulk_in_desc.bEndpointAddress; ++ fsg_ss_bulk_in_comp_desc.bMaxBurst = max_burst; ++ ++ fsg_ss_bulk_out_desc.bEndpointAddress = ++ fsg_fs_bulk_out_desc.bEndpointAddress; ++ fsg_ss_bulk_out_comp_desc.bMaxBurst = max_burst; ++ } ++ ++ if (gadget_is_otg(gadget)) ++ fsg_otg_desc.bmAttributes |= USB_OTG_HNP; ++ ++ rc = -ENOMEM; ++ ++ /* Allocate the request and buffer for endpoint 0 */ ++ fsg->ep0req = req = usb_ep_alloc_request(fsg->ep0, GFP_KERNEL); ++ if (!req) ++ goto out; ++ req->buf = kmalloc(EP0_BUFSIZE, GFP_KERNEL); ++ if (!req->buf) ++ goto out; ++ req->complete = ep0_complete; ++ ++ /* Allocate the data buffers */ ++ for (i = 0; i < fsg_num_buffers; ++i) { ++ struct fsg_buffhd *bh = &fsg->buffhds[i]; ++ ++ /* Allocate for the bulk-in endpoint. We assume that ++ * the buffer will also work with the bulk-out (and ++ * interrupt-in) endpoint. */ ++ bh->buf = kmalloc(mod_data.buflen, GFP_KERNEL); ++ if (!bh->buf) ++ goto out; ++ bh->next = bh + 1; ++ } ++ fsg->buffhds[fsg_num_buffers - 1].next = &fsg->buffhds[0]; ++ ++ /* This should reflect the actual gadget power source */ ++ usb_gadget_set_selfpowered(gadget); ++ ++ snprintf(fsg_string_manufacturer, sizeof fsg_string_manufacturer, ++ "%s %s with %s", ++ init_utsname()->sysname, init_utsname()->release, ++ gadget->name); ++ ++ fsg->thread_task = kthread_create(fsg_main_thread, fsg, ++ "file-storage-gadget"); ++ if (IS_ERR(fsg->thread_task)) { ++ rc = PTR_ERR(fsg->thread_task); ++ goto out; ++ } ++ ++ INFO(fsg, DRIVER_DESC ", version: " DRIVER_VERSION "\n"); ++ INFO(fsg, "NOTE: This driver is deprecated. " ++ "Consider using g_mass_storage instead.\n"); ++ INFO(fsg, "Number of LUNs=%d\n", fsg->nluns); ++ ++ pathbuf = kmalloc(PATH_MAX, GFP_KERNEL); ++ for (i = 0; i < fsg->nluns; ++i) { ++ curlun = &fsg->luns[i]; ++ if (fsg_lun_is_open(curlun)) { ++ p = NULL; ++ if (pathbuf) { ++ p = d_path(&curlun->filp->f_path, ++ pathbuf, PATH_MAX); ++ if (IS_ERR(p)) ++ p = NULL; ++ } ++ LINFO(curlun, "ro=%d, nofua=%d, file: %s\n", ++ curlun->ro, curlun->nofua, (p ? p : "(error)")); ++ } ++ } ++ kfree(pathbuf); ++ ++ DBG(fsg, "transport=%s (x%02x)\n", ++ mod_data.transport_name, mod_data.transport_type); ++ DBG(fsg, "protocol=%s (x%02x)\n", ++ mod_data.protocol_name, mod_data.protocol_type); ++ DBG(fsg, "VendorID=x%04x, ProductID=x%04x, Release=x%04x\n", ++ mod_data.vendor, mod_data.product, mod_data.release); ++ DBG(fsg, "removable=%d, stall=%d, cdrom=%d, buflen=%u\n", ++ mod_data.removable, mod_data.can_stall, ++ mod_data.cdrom, mod_data.buflen); ++ DBG(fsg, "I/O thread pid: %d\n", task_pid_nr(fsg->thread_task)); ++ ++ set_bit(REGISTERED, &fsg->atomic_bitflags); ++ ++ /* Tell the thread to start working */ ++ wake_up_process(fsg->thread_task); ++ return 0; ++ ++autoconf_fail: ++ ERROR(fsg, "unable to autoconfigure all endpoints\n"); ++ rc = -ENOTSUPP; ++ ++out: ++ fsg->state = FSG_STATE_TERMINATED; // The thread is dead ++ fsg_unbind(gadget); ++ complete(&fsg->thread_notifier); ++ return rc; ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static void fsg_suspend(struct usb_gadget *gadget) ++{ ++ struct fsg_dev *fsg = get_gadget_data(gadget); ++ ++ DBG(fsg, "suspend\n"); ++ set_bit(SUSPENDED, &fsg->atomic_bitflags); ++} ++ ++static void fsg_resume(struct usb_gadget *gadget) ++{ ++ struct fsg_dev *fsg = get_gadget_data(gadget); ++ ++ DBG(fsg, "resume\n"); ++ clear_bit(SUSPENDED, &fsg->atomic_bitflags); ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static struct usb_gadget_driver fsg_driver = { ++ .max_speed = USB_SPEED_SUPER, ++ .function = (char *) fsg_string_product, ++ .unbind = fsg_unbind, ++ .disconnect = fsg_disconnect, ++ .setup = fsg_setup, ++ .suspend = fsg_suspend, ++ .resume = fsg_resume, ++ ++ .driver = { ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ // .release = ... ++ // .suspend = ... ++ // .resume = ... ++ }, ++}; ++ ++ ++static int __init fsg_alloc(void) ++{ ++ struct fsg_dev *fsg; ++ ++ fsg = kzalloc(sizeof *fsg + ++ fsg_num_buffers * sizeof *(fsg->buffhds), GFP_KERNEL); ++ ++ if (!fsg) ++ return -ENOMEM; ++ spin_lock_init(&fsg->lock); ++ init_rwsem(&fsg->filesem); ++ kref_init(&fsg->ref); ++ init_completion(&fsg->thread_notifier); ++ ++ the_fsg = fsg; ++ return 0; ++} ++ ++ ++static int __init fsg_init(void) ++{ ++ int rc; ++ struct fsg_dev *fsg; ++ ++ rc = fsg_num_buffers_validate(); ++ if (rc != 0) ++ return rc; ++ ++ if ((rc = fsg_alloc()) != 0) ++ return rc; ++ fsg = the_fsg; ++ if ((rc = usb_gadget_probe_driver(&fsg_driver, fsg_bind)) != 0) ++ kref_put(&fsg->ref, fsg_release); ++ return rc; ++} ++module_init(fsg_init); ++ ++ ++static void __exit fsg_cleanup(void) ++{ ++ struct fsg_dev *fsg = the_fsg; ++ ++ /* Unregister the driver iff the thread hasn't already done so */ ++ if (test_and_clear_bit(REGISTERED, &fsg->atomic_bitflags)) ++ usb_gadget_unregister_driver(&fsg_driver); ++ ++ /* Wait for the thread to finish up */ ++ wait_for_completion(&fsg->thread_notifier); ++ ++ kref_put(&fsg->ref, fsg_release); ++} ++module_exit(fsg_cleanup); +--- a/drivers/usb/host/Kconfig ++++ b/drivers/usb/host/Kconfig +@@ -741,6 +741,16 @@ config USB_RENESAS_USBHS_HCD + To compile this driver as a module, choose M here: the + module will be called renesas-usbhs. + ++config USB_DWCOTG ++ bool "Synopsis DWC host support" ++ depends on USB && (FIQ || ARM64) ++ help ++ The Synopsis DWC controller is a dual-role ++ host/peripheral/OTG ("On The Go") USB controllers. ++ ++ Enable this option to support this IP in host controller mode. ++ If unsure, say N. ++ + config USB_IMX21_HCD + tristate "i.MX21 HCD support" + depends on ARM && ARCH_MXC +--- a/drivers/usb/host/Makefile ++++ b/drivers/usb/host/Makefile +@@ -81,6 +81,7 @@ obj-$(CONFIG_USB_SL811_HCD) += sl811-hcd + obj-$(CONFIG_USB_SL811_CS) += sl811_cs.o + obj-$(CONFIG_USB_U132_HCD) += u132-hcd.o + obj-$(CONFIG_USB_R8A66597_HCD) += r8a66597-hcd.o ++obj-$(CONFIG_USB_DWCOTG) += dwc_otg/ dwc_common_port/ + obj-$(CONFIG_USB_IMX21_HCD) += imx21-hcd.o + obj-$(CONFIG_USB_FSL_USB2) += fsl-mph-dr-of.o + obj-$(CONFIG_USB_EHCI_FSL) += fsl-mph-dr-of.o +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/Makefile +@@ -0,0 +1,58 @@ ++# ++# Makefile for DWC_common library ++# ++ ++ifneq ($(KERNELRELEASE),) ++ ++ccflags-y += -DDWC_LINUX ++#ccflags-y += -DDEBUG ++#ccflags-y += -DDWC_DEBUG_REGS ++#ccflags-y += -DDWC_DEBUG_MEMORY ++ ++ccflags-y += -DDWC_LIBMODULE ++ccflags-y += -DDWC_CCLIB ++#ccflags-y += -DDWC_CRYPTOLIB ++ccflags-y += -DDWC_NOTIFYLIB ++ccflags-y += -DDWC_UTFLIB ++ ++obj-$(CONFIG_USB_DWCOTG) += dwc_common_port_lib.o ++dwc_common_port_lib-objs := dwc_cc.o dwc_modpow.o dwc_dh.o \ ++ dwc_crypto.o dwc_notifier.o \ ++ dwc_common_linux.o dwc_mem.o ++ ++kernrelwd := $(subst ., ,$(KERNELRELEASE)) ++kernrel3 := $(word 1,$(kernrelwd)).$(word 2,$(kernrelwd)).$(word 3,$(kernrelwd)) ++ ++ifneq ($(kernrel3),2.6.20) ++# grayg - I only know that we use ccflags-y in 2.6.31 actually ++ccflags-y += $(CPPFLAGS) ++endif ++ ++else ++ ++#ifeq ($(KDIR),) ++#$(error Must give "KDIR=/path/to/kernel/source" on command line or in environment) ++#endif ++ ++ifeq ($(ARCH),) ++$(error Must give "ARCH=" on command line or in environment. Also, if \ ++ cross-compiling, must give "CROSS_COMPILE=/path/to/compiler/plus/tool-prefix-") ++endif ++ ++ifeq ($(DOXYGEN),) ++DOXYGEN := doxygen ++endif ++ ++default: ++ $(MAKE) -C$(KDIR) M=$(PWD) ARCH=$(ARCH) CROSS_COMPILE=$(CROSS_COMPILE) modules ++ ++docs: $(wildcard *.[hc]) doc/doxygen.cfg ++ $(DOXYGEN) doc/doxygen.cfg ++ ++tags: $(wildcard *.[hc]) ++ $(CTAGS) -e $(wildcard *.[hc]) $(wildcard linux/*.[hc]) $(wildcard $(KDIR)/include/linux/usb*.h) ++ ++endif ++ ++clean: ++ rm -rf *.o *.ko .*.cmd *.mod.c .*.o.d .*.o.tmp modules.order Module.markers Module.symvers .tmp_versions/ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/Makefile.fbsd +@@ -0,0 +1,17 @@ ++CFLAGS += -I/sys/i386/compile/GENERIC -I/sys/i386/include -I/usr/include ++CFLAGS += -DDWC_FREEBSD ++CFLAGS += -DDEBUG ++#CFLAGS += -DDWC_DEBUG_REGS ++#CFLAGS += -DDWC_DEBUG_MEMORY ++ ++#CFLAGS += -DDWC_LIBMODULE ++#CFLAGS += -DDWC_CCLIB ++#CFLAGS += -DDWC_CRYPTOLIB ++#CFLAGS += -DDWC_NOTIFYLIB ++#CFLAGS += -DDWC_UTFLIB ++ ++KMOD = dwc_common_port_lib ++SRCS = dwc_cc.c dwc_modpow.c dwc_dh.c dwc_crypto.c dwc_notifier.c \ ++ dwc_common_fbsd.c dwc_mem.c ++ ++.include +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/Makefile.linux +@@ -0,0 +1,49 @@ ++# ++# Makefile for DWC_common library ++# ++ifneq ($(KERNELRELEASE),) ++ ++ccflags-y += -DDWC_LINUX ++#ccflags-y += -DDEBUG ++#ccflags-y += -DDWC_DEBUG_REGS ++#ccflags-y += -DDWC_DEBUG_MEMORY ++ ++ccflags-y += -DDWC_LIBMODULE ++ccflags-y += -DDWC_CCLIB ++ccflags-y += -DDWC_CRYPTOLIB ++ccflags-y += -DDWC_NOTIFYLIB ++ccflags-y += -DDWC_UTFLIB ++ ++obj-m := dwc_common_port_lib.o ++dwc_common_port_lib-objs := dwc_cc.o dwc_modpow.o dwc_dh.o \ ++ dwc_crypto.o dwc_notifier.o \ ++ dwc_common_linux.o dwc_mem.o ++ ++else ++ ++ifeq ($(KDIR),) ++$(error Must give "KDIR=/path/to/kernel/source" on command line or in environment) ++endif ++ ++ifeq ($(ARCH),) ++$(error Must give "ARCH=" on command line or in environment. Also, if \ ++ cross-compiling, must give "CROSS_COMPILE=/path/to/compiler/plus/tool-prefix-") ++endif ++ ++ifeq ($(DOXYGEN),) ++DOXYGEN := doxygen ++endif ++ ++default: ++ $(MAKE) -C$(KDIR) M=$(PWD) ARCH=$(ARCH) CROSS_COMPILE=$(CROSS_COMPILE) modules ++ ++docs: $(wildcard *.[hc]) doc/doxygen.cfg ++ $(DOXYGEN) doc/doxygen.cfg ++ ++tags: $(wildcard *.[hc]) ++ $(CTAGS) -e $(wildcard *.[hc]) $(wildcard linux/*.[hc]) $(wildcard $(KDIR)/include/linux/usb*.h) ++ ++endif ++ ++clean: ++ rm -rf *.o *.ko .*.cmd *.mod.c .*.o.d .*.o.tmp modules.order Module.markers Module.symvers .tmp_versions/ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/changes.txt +@@ -0,0 +1,174 @@ ++ ++dwc_read_reg32() and friends now take an additional parameter, a pointer to an ++IO context struct. The IO context struct should live in an os-dependent struct ++in your driver. As an example, the dwc_usb3 driver has an os-dependent struct ++named 'os_dep' embedded in the main device struct. So there these calls look ++like this: ++ ++ dwc_read_reg32(&usb3_dev->os_dep.ioctx, &pcd->dev_global_regs->dcfg); ++ ++ dwc_write_reg32(&usb3_dev->os_dep.ioctx, ++ &pcd->dev_global_regs->dcfg, 0); ++ ++Note that for the existing Linux driver ports, it is not necessary to actually ++define the 'ioctx' member in the os-dependent struct. Since Linux does not ++require an IO context, its macros for dwc_read_reg32() and friends do not ++use the context pointer, so it is optimized away by the compiler. But it is ++necessary to add the pointer parameter to all of the call sites, to be ready ++for any future ports (such as FreeBSD) which do require an IO context. ++ ++ ++Similarly, dwc_alloc(), dwc_alloc_atomic(), dwc_strdup(), and dwc_free() now ++take an additional parameter, a pointer to a memory context. Examples: ++ ++ addr = dwc_alloc(&usb3_dev->os_dep.memctx, size); ++ ++ dwc_free(&usb3_dev->os_dep.memctx, addr); ++ ++Again, for the Linux ports, it is not necessary to actually define the memctx ++member, but it is necessary to add the pointer parameter to all of the call ++sites. ++ ++ ++Same for dwc_dma_alloc() and dwc_dma_free(). Examples: ++ ++ virt_addr = dwc_dma_alloc(&usb3_dev->os_dep.dmactx, size, &phys_addr); ++ ++ dwc_dma_free(&usb3_dev->os_dep.dmactx, size, virt_addr, phys_addr); ++ ++ ++Same for dwc_mutex_alloc() and dwc_mutex_free(). Examples: ++ ++ mutex = dwc_mutex_alloc(&usb3_dev->os_dep.mtxctx); ++ ++ dwc_mutex_free(&usb3_dev->os_dep.mtxctx, mutex); ++ ++ ++Same for dwc_spinlock_alloc() and dwc_spinlock_free(). Examples: ++ ++ lock = dwc_spinlock_alloc(&usb3_dev->osdep.splctx); ++ ++ dwc_spinlock_free(&usb3_dev->osdep.splctx, lock); ++ ++ ++Same for dwc_timer_alloc(). Example: ++ ++ timer = dwc_timer_alloc(&usb3_dev->os_dep.tmrctx, "dwc_usb3_tmr1", ++ cb_func, cb_data); ++ ++ ++Same for dwc_waitq_alloc(). Example: ++ ++ waitq = dwc_waitq_alloc(&usb3_dev->os_dep.wtqctx); ++ ++ ++Same for dwc_thread_run(). Example: ++ ++ thread = dwc_thread_run(&usb3_dev->os_dep.thdctx, func, ++ "dwc_usb3_thd1", data); ++ ++ ++Same for dwc_workq_alloc(). Example: ++ ++ workq = dwc_workq_alloc(&usb3_dev->osdep.wkqctx, "dwc_usb3_wkq1"); ++ ++ ++Same for dwc_task_alloc(). Example: ++ ++ task = dwc_task_alloc(&usb3_dev->os_dep.tskctx, "dwc_usb3_tsk1", ++ cb_func, cb_data); ++ ++ ++In addition to the context pointer additions, a few core functions have had ++other changes made to their parameters: ++ ++The 'flags' parameter to dwc_spinlock_irqsave() and dwc_spinunlock_irqrestore() ++has been changed from a uint64_t to a dwc_irqflags_t. ++ ++dwc_thread_should_stop() now takes a 'dwc_thread_t *' parameter, because the ++FreeBSD equivalent of that function requires it. ++ ++And, in addition to the context pointer, dwc_task_alloc() also adds a ++'char *name' parameter, to be consistent with dwc_thread_run() and ++dwc_workq_alloc(), and because the FreeBSD equivalent of that function ++requires a unique name. ++ ++ ++Here is a complete list of the core functions that now take a pointer to a ++context as their first parameter: ++ ++ dwc_read_reg32 ++ dwc_read_reg64 ++ dwc_write_reg32 ++ dwc_write_reg64 ++ dwc_modify_reg32 ++ dwc_modify_reg64 ++ dwc_alloc ++ dwc_alloc_atomic ++ dwc_strdup ++ dwc_free ++ dwc_dma_alloc ++ dwc_dma_free ++ dwc_mutex_alloc ++ dwc_mutex_free ++ dwc_spinlock_alloc ++ dwc_spinlock_free ++ dwc_timer_alloc ++ dwc_waitq_alloc ++ dwc_thread_run ++ dwc_workq_alloc ++ dwc_task_alloc Also adds a 'char *name' as its 2nd parameter ++ ++And here are the core functions that have other changes to their parameters: ++ ++ dwc_spinlock_irqsave 'flags' param is now a 'dwc_irqflags_t *' ++ dwc_spinunlock_irqrestore 'flags' param is now a 'dwc_irqflags_t' ++ dwc_thread_should_stop Adds a 'dwc_thread_t *' parameter ++ ++ ++ ++The changes to the core functions also require some of the other library ++functions to change: ++ ++ dwc_cc_if_alloc() and dwc_cc_if_free() now take a 'void *memctx' ++ (for memory allocation) as the 1st param and a 'void *mtxctx' ++ (for mutex allocation) as the 2nd param. ++ ++ dwc_cc_clear(), dwc_cc_add(), dwc_cc_change(), dwc_cc_remove(), ++ dwc_cc_data_for_save(), and dwc_cc_restore_from_data() now take a ++ 'void *memctx' as the 1st param. ++ ++ dwc_dh_modpow(), dwc_dh_pk(), and dwc_dh_derive_keys() now take a ++ 'void *memctx' as the 1st param. ++ ++ dwc_modpow() now takes a 'void *memctx' as the 1st param. ++ ++ dwc_alloc_notification_manager() now takes a 'void *memctx' as the ++ 1st param and a 'void *wkqctx' (for work queue allocation) as the 2nd ++ param, and also now returns an integer value that is non-zero if ++ allocation of its data structures or work queue fails. ++ ++ dwc_register_notifier() now takes a 'void *memctx' as the 1st param. ++ ++ dwc_memory_debug_start() now takes a 'void *mem_ctx' as the first ++ param, and also now returns an integer value that is non-zero if ++ allocation of its data structures fails. ++ ++ ++ ++Other miscellaneous changes: ++ ++The DEBUG_MEMORY and DEBUG_REGS #define's have been renamed to ++DWC_DEBUG_MEMORY and DWC_DEBUG_REGS. ++ ++The following #define's have been added to allow selectively compiling library ++features: ++ ++ DWC_CCLIB ++ DWC_CRYPTOLIB ++ DWC_NOTIFYLIB ++ DWC_UTFLIB ++ ++A DWC_LIBMODULE #define has also been added. If this is not defined, then the ++module code in dwc_common_linux.c is not compiled in. This allows linking the ++library code directly into a driver module, instead of as a standalone module. +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/doc/doxygen.cfg +@@ -0,0 +1,270 @@ ++# Doxyfile 1.4.5 ++ ++#--------------------------------------------------------------------------- ++# Project related configuration options ++#--------------------------------------------------------------------------- ++PROJECT_NAME = "Synopsys DWC Portability and Common Library for UWB" ++PROJECT_NUMBER = ++OUTPUT_DIRECTORY = doc ++CREATE_SUBDIRS = NO ++OUTPUT_LANGUAGE = English ++BRIEF_MEMBER_DESC = YES ++REPEAT_BRIEF = YES ++ABBREVIATE_BRIEF = "The $name class" \ ++ "The $name widget" \ ++ "The $name file" \ ++ is \ ++ provides \ ++ specifies \ ++ contains \ ++ represents \ ++ a \ ++ an \ ++ the ++ALWAYS_DETAILED_SEC = YES ++INLINE_INHERITED_MEMB = NO ++FULL_PATH_NAMES = NO ++STRIP_FROM_PATH = .. ++STRIP_FROM_INC_PATH = ++SHORT_NAMES = NO ++JAVADOC_AUTOBRIEF = YES ++MULTILINE_CPP_IS_BRIEF = NO ++DETAILS_AT_TOP = YES ++INHERIT_DOCS = YES ++SEPARATE_MEMBER_PAGES = NO ++TAB_SIZE = 8 ++ALIASES = ++OPTIMIZE_OUTPUT_FOR_C = YES ++OPTIMIZE_OUTPUT_JAVA = NO ++BUILTIN_STL_SUPPORT = NO ++DISTRIBUTE_GROUP_DOC = NO ++SUBGROUPING = NO ++#--------------------------------------------------------------------------- ++# Build related configuration options ++#--------------------------------------------------------------------------- ++EXTRACT_ALL = NO ++EXTRACT_PRIVATE = NO ++EXTRACT_STATIC = YES ++EXTRACT_LOCAL_CLASSES = NO ++EXTRACT_LOCAL_METHODS = NO ++HIDE_UNDOC_MEMBERS = NO ++HIDE_UNDOC_CLASSES = NO ++HIDE_FRIEND_COMPOUNDS = NO ++HIDE_IN_BODY_DOCS = NO ++INTERNAL_DOCS = NO ++CASE_SENSE_NAMES = YES ++HIDE_SCOPE_NAMES = NO ++SHOW_INCLUDE_FILES = NO ++INLINE_INFO = YES ++SORT_MEMBER_DOCS = NO ++SORT_BRIEF_DOCS = NO ++SORT_BY_SCOPE_NAME = NO ++GENERATE_TODOLIST = YES ++GENERATE_TESTLIST = YES ++GENERATE_BUGLIST = YES ++GENERATE_DEPRECATEDLIST= YES ++ENABLED_SECTIONS = ++MAX_INITIALIZER_LINES = 30 ++SHOW_USED_FILES = YES ++SHOW_DIRECTORIES = YES ++FILE_VERSION_FILTER = ++#--------------------------------------------------------------------------- ++# configuration options related to warning and progress messages ++#--------------------------------------------------------------------------- ++QUIET = YES ++WARNINGS = YES ++WARN_IF_UNDOCUMENTED = NO ++WARN_IF_DOC_ERROR = YES ++WARN_NO_PARAMDOC = YES ++WARN_FORMAT = "$file:$line: $text" ++WARN_LOGFILE = ++#--------------------------------------------------------------------------- ++# configuration options related to the input files ++#--------------------------------------------------------------------------- ++INPUT = . ++FILE_PATTERNS = *.c \ ++ *.cc \ ++ *.cxx \ ++ *.cpp \ ++ *.c++ \ ++ *.d \ ++ *.java \ ++ *.ii \ ++ *.ixx \ ++ *.ipp \ ++ *.i++ \ ++ *.inl \ ++ *.h \ ++ *.hh \ ++ *.hxx \ ++ *.hpp \ ++ *.h++ \ ++ *.idl \ ++ *.odl \ ++ *.cs \ ++ *.php \ ++ *.php3 \ ++ *.inc \ ++ *.m \ ++ *.mm \ ++ *.dox \ ++ *.py \ ++ *.C \ ++ *.CC \ ++ *.C++ \ ++ *.II \ ++ *.I++ \ ++ *.H \ ++ *.HH \ ++ *.H++ \ ++ *.CS \ ++ *.PHP \ ++ *.PHP3 \ ++ *.M \ ++ *.MM \ ++ *.PY ++RECURSIVE = NO ++EXCLUDE = ++EXCLUDE_SYMLINKS = NO ++EXCLUDE_PATTERNS = ++EXAMPLE_PATH = ++EXAMPLE_PATTERNS = * ++EXAMPLE_RECURSIVE = NO ++IMAGE_PATH = ++INPUT_FILTER = ++FILTER_PATTERNS = ++FILTER_SOURCE_FILES = NO ++#--------------------------------------------------------------------------- ++# configuration options related to source browsing ++#--------------------------------------------------------------------------- ++SOURCE_BROWSER = NO ++INLINE_SOURCES = NO ++STRIP_CODE_COMMENTS = YES ++REFERENCED_BY_RELATION = YES ++REFERENCES_RELATION = YES ++USE_HTAGS = NO ++VERBATIM_HEADERS = NO ++#--------------------------------------------------------------------------- ++# configuration options related to the alphabetical class index ++#--------------------------------------------------------------------------- ++ALPHABETICAL_INDEX = NO ++COLS_IN_ALPHA_INDEX = 5 ++IGNORE_PREFIX = ++#--------------------------------------------------------------------------- ++# configuration options related to the HTML output ++#--------------------------------------------------------------------------- ++GENERATE_HTML = YES ++HTML_OUTPUT = html ++HTML_FILE_EXTENSION = .html ++HTML_HEADER = ++HTML_FOOTER = ++HTML_STYLESHEET = ++HTML_ALIGN_MEMBERS = YES ++GENERATE_HTMLHELP = NO ++CHM_FILE = ++HHC_LOCATION = ++GENERATE_CHI = NO ++BINARY_TOC = NO ++TOC_EXPAND = NO ++DISABLE_INDEX = NO ++ENUM_VALUES_PER_LINE = 4 ++GENERATE_TREEVIEW = YES ++TREEVIEW_WIDTH = 250 ++#--------------------------------------------------------------------------- ++# configuration options related to the LaTeX output ++#--------------------------------------------------------------------------- ++GENERATE_LATEX = NO ++LATEX_OUTPUT = latex ++LATEX_CMD_NAME = latex ++MAKEINDEX_CMD_NAME = makeindex ++COMPACT_LATEX = NO ++PAPER_TYPE = a4wide ++EXTRA_PACKAGES = ++LATEX_HEADER = ++PDF_HYPERLINKS = NO ++USE_PDFLATEX = NO ++LATEX_BATCHMODE = NO ++LATEX_HIDE_INDICES = NO ++#--------------------------------------------------------------------------- ++# configuration options related to the RTF output ++#--------------------------------------------------------------------------- ++GENERATE_RTF = NO ++RTF_OUTPUT = rtf ++COMPACT_RTF = NO ++RTF_HYPERLINKS = NO ++RTF_STYLESHEET_FILE = ++RTF_EXTENSIONS_FILE = ++#--------------------------------------------------------------------------- ++# configuration options related to the man page output ++#--------------------------------------------------------------------------- ++GENERATE_MAN = NO ++MAN_OUTPUT = man ++MAN_EXTENSION = .3 ++MAN_LINKS = NO ++#--------------------------------------------------------------------------- ++# configuration options related to the XML output ++#--------------------------------------------------------------------------- ++GENERATE_XML = NO ++XML_OUTPUT = xml ++XML_SCHEMA = ++XML_DTD = ++XML_PROGRAMLISTING = YES ++#--------------------------------------------------------------------------- ++# configuration options for the AutoGen Definitions output ++#--------------------------------------------------------------------------- ++GENERATE_AUTOGEN_DEF = NO ++#--------------------------------------------------------------------------- ++# configuration options related to the Perl module output ++#--------------------------------------------------------------------------- ++GENERATE_PERLMOD = NO ++PERLMOD_LATEX = NO ++PERLMOD_PRETTY = YES ++PERLMOD_MAKEVAR_PREFIX = ++#--------------------------------------------------------------------------- ++# Configuration options related to the preprocessor ++#--------------------------------------------------------------------------- ++ENABLE_PREPROCESSING = YES ++MACRO_EXPANSION = NO ++EXPAND_ONLY_PREDEF = NO ++SEARCH_INCLUDES = YES ++INCLUDE_PATH = ++INCLUDE_FILE_PATTERNS = ++PREDEFINED = DEBUG DEBUG_MEMORY ++EXPAND_AS_DEFINED = ++SKIP_FUNCTION_MACROS = YES ++#--------------------------------------------------------------------------- ++# Configuration::additions related to external references ++#--------------------------------------------------------------------------- ++TAGFILES = ++GENERATE_TAGFILE = ++ALLEXTERNALS = NO ++EXTERNAL_GROUPS = YES ++PERL_PATH = /usr/bin/perl ++#--------------------------------------------------------------------------- ++# Configuration options related to the dot tool ++#--------------------------------------------------------------------------- ++CLASS_DIAGRAMS = YES ++HIDE_UNDOC_RELATIONS = YES ++HAVE_DOT = NO ++CLASS_GRAPH = YES ++COLLABORATION_GRAPH = YES ++GROUP_GRAPHS = YES ++UML_LOOK = NO ++TEMPLATE_RELATIONS = NO ++INCLUDE_GRAPH = NO ++INCLUDED_BY_GRAPH = YES ++CALL_GRAPH = NO ++GRAPHICAL_HIERARCHY = YES ++DIRECTORY_GRAPH = YES ++DOT_IMAGE_FORMAT = png ++DOT_PATH = ++DOTFILE_DIRS = ++MAX_DOT_GRAPH_DEPTH = 1000 ++DOT_TRANSPARENT = NO ++DOT_MULTI_TARGETS = NO ++GENERATE_LEGEND = YES ++DOT_CLEANUP = YES ++#--------------------------------------------------------------------------- ++# Configuration::additions related to the search engine ++#--------------------------------------------------------------------------- ++SEARCHENGINE = NO +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_cc.c +@@ -0,0 +1,532 @@ ++/* ========================================================================= ++ * $File: //dwh/usb_iip/dev/software/dwc_common_port_2/dwc_cc.c $ ++ * $Revision: #4 $ ++ * $Date: 2010/11/04 $ ++ * $Change: 1621692 $ ++ * ++ * Synopsys Portability Library Software and documentation ++ * (hereinafter, "Software") is an Unsupported proprietary work of ++ * Synopsys, Inc. unless otherwise expressly agreed to in writing ++ * between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product ++ * under any End User Software License Agreement or Agreement for ++ * Licensed Product with Synopsys or any supplement thereto. You are ++ * permitted to use and redistribute this Software in source and binary ++ * forms, with or without modification, provided that redistributions ++ * of source code must retain this notice. You may not view, use, ++ * disclose, copy or distribute this file or any information contained ++ * herein except pursuant to this license grant from Synopsys. If you ++ * do not agree with this notice, including the disclaimer below, then ++ * you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" ++ * BASIS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT ++ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS ++ * FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. IN NO EVENT SHALL ++ * SYNOPSYS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY ++ * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE ++ * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================= */ ++#ifdef DWC_CCLIB ++ ++#include "dwc_cc.h" ++ ++typedef struct dwc_cc ++{ ++ uint32_t uid; ++ uint8_t chid[16]; ++ uint8_t cdid[16]; ++ uint8_t ck[16]; ++ uint8_t *name; ++ uint8_t length; ++ DWC_CIRCLEQ_ENTRY(dwc_cc) list_entry; ++} dwc_cc_t; ++ ++DWC_CIRCLEQ_HEAD(context_list, dwc_cc); ++ ++/** The main structure for CC management. */ ++struct dwc_cc_if ++{ ++ dwc_mutex_t *mutex; ++ char *filename; ++ ++ unsigned is_host:1; ++ ++ dwc_notifier_t *notifier; ++ ++ struct context_list list; ++}; ++ ++#ifdef DEBUG ++static inline void dump_bytes(char *name, uint8_t *bytes, int len) ++{ ++ int i; ++ DWC_PRINTF("%s: ", name); ++ for (i=0; ilength = length; ++ cc->name = dwc_alloc(mem_ctx, length); ++ if (!cc->name) { ++ dwc_free(mem_ctx, cc); ++ return NULL; ++ } ++ ++ DWC_MEMCPY(cc->name, name, length); ++ } ++ ++ return cc; ++} ++ ++static void free_cc(void *mem_ctx, dwc_cc_t *cc) ++{ ++ if (cc->name) { ++ dwc_free(mem_ctx, cc->name); ++ } ++ dwc_free(mem_ctx, cc); ++} ++ ++static uint32_t next_uid(dwc_cc_if_t *cc_if) ++{ ++ uint32_t uid = 0; ++ dwc_cc_t *cc; ++ DWC_CIRCLEQ_FOREACH(cc, &cc_if->list, list_entry) { ++ if (cc->uid > uid) { ++ uid = cc->uid; ++ } ++ } ++ ++ if (uid == 0) { ++ uid = 255; ++ } ++ ++ return uid + 1; ++} ++ ++static dwc_cc_t *cc_find(dwc_cc_if_t *cc_if, uint32_t uid) ++{ ++ dwc_cc_t *cc; ++ DWC_CIRCLEQ_FOREACH(cc, &cc_if->list, list_entry) { ++ if (cc->uid == uid) { ++ return cc; ++ } ++ } ++ return NULL; ++} ++ ++static unsigned int cc_data_size(dwc_cc_if_t *cc_if) ++{ ++ unsigned int size = 0; ++ dwc_cc_t *cc; ++ DWC_CIRCLEQ_FOREACH(cc, &cc_if->list, list_entry) { ++ size += (48 + 1); ++ if (cc->name) { ++ size += cc->length; ++ } ++ } ++ return size; ++} ++ ++static uint32_t cc_match_chid(dwc_cc_if_t *cc_if, uint8_t *chid) ++{ ++ uint32_t uid = 0; ++ dwc_cc_t *cc; ++ ++ DWC_CIRCLEQ_FOREACH(cc, &cc_if->list, list_entry) { ++ if (DWC_MEMCMP(cc->chid, chid, 16) == 0) { ++ uid = cc->uid; ++ break; ++ } ++ } ++ return uid; ++} ++static uint32_t cc_match_cdid(dwc_cc_if_t *cc_if, uint8_t *cdid) ++{ ++ uint32_t uid = 0; ++ dwc_cc_t *cc; ++ ++ DWC_CIRCLEQ_FOREACH(cc, &cc_if->list, list_entry) { ++ if (DWC_MEMCMP(cc->cdid, cdid, 16) == 0) { ++ uid = cc->uid; ++ break; ++ } ++ } ++ return uid; ++} ++ ++/* Internal cc_add */ ++static int32_t cc_add(void *mem_ctx, dwc_cc_if_t *cc_if, uint8_t *chid, ++ uint8_t *cdid, uint8_t *ck, uint8_t *name, uint8_t length) ++{ ++ dwc_cc_t *cc; ++ uint32_t uid; ++ ++ if (cc_if->is_host) { ++ uid = cc_match_cdid(cc_if, cdid); ++ } ++ else { ++ uid = cc_match_chid(cc_if, chid); ++ } ++ ++ if (uid) { ++ DWC_DEBUGC("Replacing previous connection context id=%d name=%p name_len=%d", uid, name, length); ++ cc = cc_find(cc_if, uid); ++ } ++ else { ++ cc = alloc_cc(mem_ctx, name, length); ++ cc->uid = next_uid(cc_if); ++ DWC_CIRCLEQ_INSERT_TAIL(&cc_if->list, cc, list_entry); ++ } ++ ++ DWC_MEMCPY(&(cc->chid[0]), chid, 16); ++ DWC_MEMCPY(&(cc->cdid[0]), cdid, 16); ++ DWC_MEMCPY(&(cc->ck[0]), ck, 16); ++ ++ DWC_DEBUGC("Added connection context id=%d name=%p name_len=%d", cc->uid, name, length); ++ dump_bytes("CHID", cc->chid, 16); ++ dump_bytes("CDID", cc->cdid, 16); ++ dump_bytes("CK", cc->ck, 16); ++ return cc->uid; ++} ++ ++/* Internal cc_clear */ ++static void cc_clear(void *mem_ctx, dwc_cc_if_t *cc_if) ++{ ++ while (!DWC_CIRCLEQ_EMPTY(&cc_if->list)) { ++ dwc_cc_t *cc = DWC_CIRCLEQ_FIRST(&cc_if->list); ++ DWC_CIRCLEQ_REMOVE_INIT(&cc_if->list, cc, list_entry); ++ free_cc(mem_ctx, cc); ++ } ++} ++ ++dwc_cc_if_t *dwc_cc_if_alloc(void *mem_ctx, void *mtx_ctx, ++ dwc_notifier_t *notifier, unsigned is_host) ++{ ++ dwc_cc_if_t *cc_if = NULL; ++ ++ /* Allocate a common_cc_if structure */ ++ cc_if = dwc_alloc(mem_ctx, sizeof(dwc_cc_if_t)); ++ ++ if (!cc_if) ++ return NULL; ++ ++#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES)) ++ DWC_MUTEX_ALLOC_LINUX_DEBUG(cc_if->mutex); ++#else ++ cc_if->mutex = dwc_mutex_alloc(mtx_ctx); ++#endif ++ if (!cc_if->mutex) { ++ dwc_free(mem_ctx, cc_if); ++ return NULL; ++ } ++ ++ DWC_CIRCLEQ_INIT(&cc_if->list); ++ cc_if->is_host = is_host; ++ cc_if->notifier = notifier; ++ return cc_if; ++} ++ ++void dwc_cc_if_free(void *mem_ctx, void *mtx_ctx, dwc_cc_if_t *cc_if) ++{ ++#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES)) ++ DWC_MUTEX_FREE(cc_if->mutex); ++#else ++ dwc_mutex_free(mtx_ctx, cc_if->mutex); ++#endif ++ cc_clear(mem_ctx, cc_if); ++ dwc_free(mem_ctx, cc_if); ++} ++ ++static void cc_changed(dwc_cc_if_t *cc_if) ++{ ++ if (cc_if->notifier) { ++ dwc_notify(cc_if->notifier, DWC_CC_LIST_CHANGED_NOTIFICATION, cc_if); ++ } ++} ++ ++void dwc_cc_clear(void *mem_ctx, dwc_cc_if_t *cc_if) ++{ ++ DWC_MUTEX_LOCK(cc_if->mutex); ++ cc_clear(mem_ctx, cc_if); ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ cc_changed(cc_if); ++} ++ ++int32_t dwc_cc_add(void *mem_ctx, dwc_cc_if_t *cc_if, uint8_t *chid, ++ uint8_t *cdid, uint8_t *ck, uint8_t *name, uint8_t length) ++{ ++ uint32_t uid; ++ ++ DWC_MUTEX_LOCK(cc_if->mutex); ++ uid = cc_add(mem_ctx, cc_if, chid, cdid, ck, name, length); ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ cc_changed(cc_if); ++ ++ return uid; ++} ++ ++void dwc_cc_change(void *mem_ctx, dwc_cc_if_t *cc_if, int32_t id, uint8_t *chid, ++ uint8_t *cdid, uint8_t *ck, uint8_t *name, uint8_t length) ++{ ++ dwc_cc_t* cc; ++ ++ DWC_DEBUGC("Change connection context %d", id); ++ ++ DWC_MUTEX_LOCK(cc_if->mutex); ++ cc = cc_find(cc_if, id); ++ if (!cc) { ++ DWC_ERROR("Uid %d not found in cc list\n", id); ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ return; ++ } ++ ++ if (chid) { ++ DWC_MEMCPY(&(cc->chid[0]), chid, 16); ++ } ++ if (cdid) { ++ DWC_MEMCPY(&(cc->cdid[0]), cdid, 16); ++ } ++ if (ck) { ++ DWC_MEMCPY(&(cc->ck[0]), ck, 16); ++ } ++ ++ if (name) { ++ if (cc->name) { ++ dwc_free(mem_ctx, cc->name); ++ } ++ cc->name = dwc_alloc(mem_ctx, length); ++ if (!cc->name) { ++ DWC_ERROR("Out of memory in dwc_cc_change()\n"); ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ return; ++ } ++ cc->length = length; ++ DWC_MEMCPY(cc->name, name, length); ++ } ++ ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ ++ cc_changed(cc_if); ++ ++ DWC_DEBUGC("Changed connection context id=%d\n", id); ++ dump_bytes("New CHID", cc->chid, 16); ++ dump_bytes("New CDID", cc->cdid, 16); ++ dump_bytes("New CK", cc->ck, 16); ++} ++ ++void dwc_cc_remove(void *mem_ctx, dwc_cc_if_t *cc_if, int32_t id) ++{ ++ dwc_cc_t *cc; ++ ++ DWC_DEBUGC("Removing connection context %d", id); ++ ++ DWC_MUTEX_LOCK(cc_if->mutex); ++ cc = cc_find(cc_if, id); ++ if (!cc) { ++ DWC_ERROR("Uid %d not found in cc list\n", id); ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ return; ++ } ++ ++ DWC_CIRCLEQ_REMOVE_INIT(&cc_if->list, cc, list_entry); ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ free_cc(mem_ctx, cc); ++ ++ cc_changed(cc_if); ++} ++ ++uint8_t *dwc_cc_data_for_save(void *mem_ctx, dwc_cc_if_t *cc_if, unsigned int *length) ++{ ++ uint8_t *buf, *x; ++ uint8_t zero = 0; ++ dwc_cc_t *cc; ++ ++ DWC_MUTEX_LOCK(cc_if->mutex); ++ *length = cc_data_size(cc_if); ++ if (!(*length)) { ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ return NULL; ++ } ++ ++ DWC_DEBUGC("Creating data for saving (length=%d)", *length); ++ ++ buf = dwc_alloc(mem_ctx, *length); ++ if (!buf) { ++ *length = 0; ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ return NULL; ++ } ++ ++ x = buf; ++ DWC_CIRCLEQ_FOREACH(cc, &cc_if->list, list_entry) { ++ DWC_MEMCPY(x, cc->chid, 16); ++ x += 16; ++ DWC_MEMCPY(x, cc->cdid, 16); ++ x += 16; ++ DWC_MEMCPY(x, cc->ck, 16); ++ x += 16; ++ if (cc->name) { ++ DWC_MEMCPY(x, &cc->length, 1); ++ x += 1; ++ DWC_MEMCPY(x, cc->name, cc->length); ++ x += cc->length; ++ } ++ else { ++ DWC_MEMCPY(x, &zero, 1); ++ x += 1; ++ } ++ } ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ ++ return buf; ++} ++ ++void dwc_cc_restore_from_data(void *mem_ctx, dwc_cc_if_t *cc_if, uint8_t *data, uint32_t length) ++{ ++ uint8_t name_length; ++ uint8_t *name; ++ uint8_t *chid; ++ uint8_t *cdid; ++ uint8_t *ck; ++ uint32_t i = 0; ++ ++ DWC_MUTEX_LOCK(cc_if->mutex); ++ cc_clear(mem_ctx, cc_if); ++ ++ while (i < length) { ++ chid = &data[i]; ++ i += 16; ++ cdid = &data[i]; ++ i += 16; ++ ck = &data[i]; ++ i += 16; ++ ++ name_length = data[i]; ++ i ++; ++ ++ if (name_length) { ++ name = &data[i]; ++ i += name_length; ++ } ++ else { ++ name = NULL; ++ } ++ ++ /* check to see if we haven't overflown the buffer */ ++ if (i > length) { ++ DWC_ERROR("Data format error while attempting to load CCs " ++ "(nlen=%d, iter=%d, buflen=%d).\n", name_length, i, length); ++ break; ++ } ++ ++ cc_add(mem_ctx, cc_if, chid, cdid, ck, name, name_length); ++ } ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ ++ cc_changed(cc_if); ++} ++ ++uint32_t dwc_cc_match_chid(dwc_cc_if_t *cc_if, uint8_t *chid) ++{ ++ uint32_t uid = 0; ++ ++ DWC_MUTEX_LOCK(cc_if->mutex); ++ uid = cc_match_chid(cc_if, chid); ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ return uid; ++} ++uint32_t dwc_cc_match_cdid(dwc_cc_if_t *cc_if, uint8_t *cdid) ++{ ++ uint32_t uid = 0; ++ ++ DWC_MUTEX_LOCK(cc_if->mutex); ++ uid = cc_match_cdid(cc_if, cdid); ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ return uid; ++} ++ ++uint8_t *dwc_cc_ck(dwc_cc_if_t *cc_if, int32_t id) ++{ ++ uint8_t *ck = NULL; ++ dwc_cc_t *cc; ++ ++ DWC_MUTEX_LOCK(cc_if->mutex); ++ cc = cc_find(cc_if, id); ++ if (cc) { ++ ck = cc->ck; ++ } ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ ++ return ck; ++ ++} ++ ++uint8_t *dwc_cc_chid(dwc_cc_if_t *cc_if, int32_t id) ++{ ++ uint8_t *retval = NULL; ++ dwc_cc_t *cc; ++ ++ DWC_MUTEX_LOCK(cc_if->mutex); ++ cc = cc_find(cc_if, id); ++ if (cc) { ++ retval = cc->chid; ++ } ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ ++ return retval; ++} ++ ++uint8_t *dwc_cc_cdid(dwc_cc_if_t *cc_if, int32_t id) ++{ ++ uint8_t *retval = NULL; ++ dwc_cc_t *cc; ++ ++ DWC_MUTEX_LOCK(cc_if->mutex); ++ cc = cc_find(cc_if, id); ++ if (cc) { ++ retval = cc->cdid; ++ } ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ ++ return retval; ++} ++ ++uint8_t *dwc_cc_name(dwc_cc_if_t *cc_if, int32_t id, uint8_t *length) ++{ ++ uint8_t *retval = NULL; ++ dwc_cc_t *cc; ++ ++ DWC_MUTEX_LOCK(cc_if->mutex); ++ *length = 0; ++ cc = cc_find(cc_if, id); ++ if (cc) { ++ *length = cc->length; ++ retval = cc->name; ++ } ++ DWC_MUTEX_UNLOCK(cc_if->mutex); ++ ++ return retval; ++} ++ ++#endif /* DWC_CCLIB */ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_cc.h +@@ -0,0 +1,224 @@ ++/* ========================================================================= ++ * $File: //dwh/usb_iip/dev/software/dwc_common_port_2/dwc_cc.h $ ++ * $Revision: #4 $ ++ * $Date: 2010/09/28 $ ++ * $Change: 1596182 $ ++ * ++ * Synopsys Portability Library Software and documentation ++ * (hereinafter, "Software") is an Unsupported proprietary work of ++ * Synopsys, Inc. unless otherwise expressly agreed to in writing ++ * between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product ++ * under any End User Software License Agreement or Agreement for ++ * Licensed Product with Synopsys or any supplement thereto. You are ++ * permitted to use and redistribute this Software in source and binary ++ * forms, with or without modification, provided that redistributions ++ * of source code must retain this notice. You may not view, use, ++ * disclose, copy or distribute this file or any information contained ++ * herein except pursuant to this license grant from Synopsys. If you ++ * do not agree with this notice, including the disclaimer below, then ++ * you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" ++ * BASIS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT ++ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS ++ * FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. IN NO EVENT SHALL ++ * SYNOPSYS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY ++ * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE ++ * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================= */ ++#ifndef _DWC_CC_H_ ++#define _DWC_CC_H_ ++ ++#ifdef __cplusplus ++extern "C" { ++#endif ++ ++/** @file ++ * ++ * This file defines the Context Context library. ++ * ++ * The main data structure is dwc_cc_if_t which is returned by either the ++ * dwc_cc_if_alloc function or returned by the module to the user via a provided ++ * function. The data structure is opaque and should only be manipulated via the ++ * functions provied in this API. ++ * ++ * It manages a list of connection contexts and operations can be performed to ++ * add, remove, query, search, and change, those contexts. Additionally, ++ * a dwc_notifier_t object can be requested from the manager so that ++ * the user can be notified whenever the context list has changed. ++ */ ++ ++#include "dwc_os.h" ++#include "dwc_list.h" ++#include "dwc_notifier.h" ++ ++ ++/* Notifications */ ++#define DWC_CC_LIST_CHANGED_NOTIFICATION "DWC_CC_LIST_CHANGED_NOTIFICATION" ++ ++struct dwc_cc_if; ++typedef struct dwc_cc_if dwc_cc_if_t; ++ ++ ++/** @name Connection Context Operations */ ++/** @{ */ ++ ++/** This function allocates memory for a dwc_cc_if_t structure, initializes ++ * fields to default values, and returns a pointer to the structure or NULL on ++ * error. */ ++extern dwc_cc_if_t *dwc_cc_if_alloc(void *mem_ctx, void *mtx_ctx, ++ dwc_notifier_t *notifier, unsigned is_host); ++ ++/** Frees the memory for the specified CC structure allocated from ++ * dwc_cc_if_alloc(). */ ++extern void dwc_cc_if_free(void *mem_ctx, void *mtx_ctx, dwc_cc_if_t *cc_if); ++ ++/** Removes all contexts from the connection context list */ ++extern void dwc_cc_clear(void *mem_ctx, dwc_cc_if_t *cc_if); ++ ++/** Adds a connection context (CHID, CK, CDID, Name) to the connection context list. ++ * If a CHID already exists, the CK and name are overwritten. Statistics are ++ * not overwritten. ++ * ++ * @param cc_if The cc_if structure. ++ * @param chid A pointer to the 16-byte CHID. This value will be copied. ++ * @param ck A pointer to the 16-byte CK. This value will be copied. ++ * @param cdid A pointer to the 16-byte CDID. This value will be copied. ++ * @param name An optional host friendly name as defined in the association model ++ * spec. Must be a UTF16-LE unicode string. Can be NULL to indicated no name. ++ * @param length The length othe unicode string. ++ * @return A unique identifier used to refer to this context that is valid for ++ * as long as this context is still in the list. */ ++extern int32_t dwc_cc_add(void *mem_ctx, dwc_cc_if_t *cc_if, uint8_t *chid, ++ uint8_t *cdid, uint8_t *ck, uint8_t *name, ++ uint8_t length); ++ ++/** Changes the CHID, CK, CDID, or Name values of a connection context in the ++ * list, preserving any accumulated statistics. This would typically be called ++ * if the host decideds to change the context with a SET_CONNECTION request. ++ * ++ * @param cc_if The cc_if structure. ++ * @param id The identifier of the connection context. ++ * @param chid A pointer to the 16-byte CHID. This value will be copied. NULL ++ * indicates no change. ++ * @param cdid A pointer to the 16-byte CDID. This value will be copied. NULL ++ * indicates no change. ++ * @param ck A pointer to the 16-byte CK. This value will be copied. NULL ++ * indicates no change. ++ * @param name Host friendly name UTF16-LE. NULL indicates no change. ++ * @param length Length of name. */ ++extern void dwc_cc_change(void *mem_ctx, dwc_cc_if_t *cc_if, int32_t id, ++ uint8_t *chid, uint8_t *cdid, uint8_t *ck, ++ uint8_t *name, uint8_t length); ++ ++/** Remove the specified connection context. ++ * @param cc_if The cc_if structure. ++ * @param id The identifier of the connection context to remove. */ ++extern void dwc_cc_remove(void *mem_ctx, dwc_cc_if_t *cc_if, int32_t id); ++ ++/** Get a binary block of data for the connection context list and attributes. ++ * This data can be used by the OS specific driver to save the connection ++ * context list into non-volatile memory. ++ * ++ * @param cc_if The cc_if structure. ++ * @param length Return the length of the data buffer. ++ * @return A pointer to the data buffer. The memory for this buffer should be ++ * freed with DWC_FREE() after use. */ ++extern uint8_t *dwc_cc_data_for_save(void *mem_ctx, dwc_cc_if_t *cc_if, ++ unsigned int *length); ++ ++/** Restore the connection context list from the binary data that was previously ++ * returned from a call to dwc_cc_data_for_save. This can be used by the OS specific ++ * driver to load a connection context list from non-volatile memory. ++ * ++ * @param cc_if The cc_if structure. ++ * @param data The data bytes as returned from dwc_cc_data_for_save. ++ * @param length The length of the data. */ ++extern void dwc_cc_restore_from_data(void *mem_ctx, dwc_cc_if_t *cc_if, ++ uint8_t *data, unsigned int length); ++ ++/** Find the connection context from the specified CHID. ++ * ++ * @param cc_if The cc_if structure. ++ * @param chid A pointer to the CHID data. ++ * @return A non-zero identifier of the connection context if the CHID matches. ++ * Otherwise returns 0. */ ++extern uint32_t dwc_cc_match_chid(dwc_cc_if_t *cc_if, uint8_t *chid); ++ ++/** Find the connection context from the specified CDID. ++ * ++ * @param cc_if The cc_if structure. ++ * @param cdid A pointer to the CDID data. ++ * @return A non-zero identifier of the connection context if the CHID matches. ++ * Otherwise returns 0. */ ++extern uint32_t dwc_cc_match_cdid(dwc_cc_if_t *cc_if, uint8_t *cdid); ++ ++/** Retrieve the CK from the specified connection context. ++ * ++ * @param cc_if The cc_if structure. ++ * @param id The identifier of the connection context. ++ * @return A pointer to the CK data. The memory does not need to be freed. */ ++extern uint8_t *dwc_cc_ck(dwc_cc_if_t *cc_if, int32_t id); ++ ++/** Retrieve the CHID from the specified connection context. ++ * ++ * @param cc_if The cc_if structure. ++ * @param id The identifier of the connection context. ++ * @return A pointer to the CHID data. The memory does not need to be freed. */ ++extern uint8_t *dwc_cc_chid(dwc_cc_if_t *cc_if, int32_t id); ++ ++/** Retrieve the CDID from the specified connection context. ++ * ++ * @param cc_if The cc_if structure. ++ * @param id The identifier of the connection context. ++ * @return A pointer to the CDID data. The memory does not need to be freed. */ ++extern uint8_t *dwc_cc_cdid(dwc_cc_if_t *cc_if, int32_t id); ++ ++extern uint8_t *dwc_cc_name(dwc_cc_if_t *cc_if, int32_t id, uint8_t *length); ++ ++/** Checks a buffer for non-zero. ++ * @param id A pointer to a 16 byte buffer. ++ * @return true if the 16 byte value is non-zero. */ ++static inline unsigned dwc_assoc_is_not_zero_id(uint8_t *id) { ++ int i; ++ for (i=0; i<16; i++) { ++ if (id[i]) return 1; ++ } ++ return 0; ++} ++ ++/** Checks a buffer for zero. ++ * @param id A pointer to a 16 byte buffer. ++ * @return true if the 16 byte value is zero. */ ++static inline unsigned dwc_assoc_is_zero_id(uint8_t *id) { ++ return !dwc_assoc_is_not_zero_id(id); ++} ++ ++/** Prints an ASCII representation for the 16-byte chid, cdid, or ck, into ++ * buffer. */ ++static inline int dwc_print_id_string(char *buffer, uint8_t *id) { ++ char *ptr = buffer; ++ int i; ++ for (i=0; i<16; i++) { ++ ptr += DWC_SPRINTF(ptr, "%02x", id[i]); ++ if (i < 15) { ++ ptr += DWC_SPRINTF(ptr, " "); ++ } ++ } ++ return ptr - buffer; ++} ++ ++/** @} */ ++ ++#ifdef __cplusplus ++} ++#endif ++ ++#endif /* _DWC_CC_H_ */ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_common_fbsd.c +@@ -0,0 +1,1308 @@ ++#include "dwc_os.h" ++#include "dwc_list.h" ++ ++#ifdef DWC_CCLIB ++# include "dwc_cc.h" ++#endif ++ ++#ifdef DWC_CRYPTOLIB ++# include "dwc_modpow.h" ++# include "dwc_dh.h" ++# include "dwc_crypto.h" ++#endif ++ ++#ifdef DWC_NOTIFYLIB ++# include "dwc_notifier.h" ++#endif ++ ++/* OS-Level Implementations */ ++ ++/* This is the FreeBSD 7.0 kernel implementation of the DWC platform library. */ ++ ++ ++/* MISC */ ++ ++void *DWC_MEMSET(void *dest, uint8_t byte, uint32_t size) ++{ ++ return memset(dest, byte, size); ++} ++ ++void *DWC_MEMCPY(void *dest, void const *src, uint32_t size) ++{ ++ return memcpy(dest, src, size); ++} ++ ++void *DWC_MEMMOVE(void *dest, void *src, uint32_t size) ++{ ++ bcopy(src, dest, size); ++ return dest; ++} ++ ++int DWC_MEMCMP(void *m1, void *m2, uint32_t size) ++{ ++ return memcmp(m1, m2, size); ++} ++ ++int DWC_STRNCMP(void *s1, void *s2, uint32_t size) ++{ ++ return strncmp(s1, s2, size); ++} ++ ++int DWC_STRCMP(void *s1, void *s2) ++{ ++ return strcmp(s1, s2); ++} ++ ++int DWC_STRLEN(char const *str) ++{ ++ return strlen(str); ++} ++ ++char *DWC_STRCPY(char *to, char const *from) ++{ ++ return strcpy(to, from); ++} ++ ++char *DWC_STRDUP(char const *str) ++{ ++ int len = DWC_STRLEN(str) + 1; ++ char *new = DWC_ALLOC_ATOMIC(len); ++ ++ if (!new) { ++ return NULL; ++ } ++ ++ DWC_MEMCPY(new, str, len); ++ return new; ++} ++ ++int DWC_ATOI(char *str, int32_t *value) ++{ ++ char *end = NULL; ++ ++ *value = strtol(str, &end, 0); ++ if (*end == '\0') { ++ return 0; ++ } ++ ++ return -1; ++} ++ ++int DWC_ATOUI(char *str, uint32_t *value) ++{ ++ char *end = NULL; ++ ++ *value = strtoul(str, &end, 0); ++ if (*end == '\0') { ++ return 0; ++ } ++ ++ return -1; ++} ++ ++ ++#ifdef DWC_UTFLIB ++/* From usbstring.c */ ++ ++int DWC_UTF8_TO_UTF16LE(uint8_t const *s, uint16_t *cp, unsigned len) ++{ ++ int count = 0; ++ u8 c; ++ u16 uchar; ++ ++ /* this insists on correct encodings, though not minimal ones. ++ * BUT it currently rejects legit 4-byte UTF-8 code points, ++ * which need surrogate pairs. (Unicode 3.1 can use them.) ++ */ ++ while (len != 0 && (c = (u8) *s++) != 0) { ++ if (unlikely(c & 0x80)) { ++ // 2-byte sequence: ++ // 00000yyyyyxxxxxx = 110yyyyy 10xxxxxx ++ if ((c & 0xe0) == 0xc0) { ++ uchar = (c & 0x1f) << 6; ++ ++ c = (u8) *s++; ++ if ((c & 0xc0) != 0xc0) ++ goto fail; ++ c &= 0x3f; ++ uchar |= c; ++ ++ // 3-byte sequence (most CJKV characters): ++ // zzzzyyyyyyxxxxxx = 1110zzzz 10yyyyyy 10xxxxxx ++ } else if ((c & 0xf0) == 0xe0) { ++ uchar = (c & 0x0f) << 12; ++ ++ c = (u8) *s++; ++ if ((c & 0xc0) != 0xc0) ++ goto fail; ++ c &= 0x3f; ++ uchar |= c << 6; ++ ++ c = (u8) *s++; ++ if ((c & 0xc0) != 0xc0) ++ goto fail; ++ c &= 0x3f; ++ uchar |= c; ++ ++ /* no bogus surrogates */ ++ if (0xd800 <= uchar && uchar <= 0xdfff) ++ goto fail; ++ ++ // 4-byte sequence (surrogate pairs, currently rare): ++ // 11101110wwwwzzzzyy + 110111yyyyxxxxxx ++ // = 11110uuu 10uuzzzz 10yyyyyy 10xxxxxx ++ // (uuuuu = wwww + 1) ++ // FIXME accept the surrogate code points (only) ++ } else ++ goto fail; ++ } else ++ uchar = c; ++ put_unaligned (cpu_to_le16 (uchar), cp++); ++ count++; ++ len--; ++ } ++ return count; ++fail: ++ return -1; ++} ++ ++#endif /* DWC_UTFLIB */ ++ ++ ++/* dwc_debug.h */ ++ ++dwc_bool_t DWC_IN_IRQ(void) ++{ ++// return in_irq(); ++ return 0; ++} ++ ++dwc_bool_t DWC_IN_BH(void) ++{ ++// return in_softirq(); ++ return 0; ++} ++ ++void DWC_VPRINTF(char *format, va_list args) ++{ ++ vprintf(format, args); ++} ++ ++int DWC_VSNPRINTF(char *str, int size, char *format, va_list args) ++{ ++ return vsnprintf(str, size, format, args); ++} ++ ++void DWC_PRINTF(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++} ++ ++int DWC_SPRINTF(char *buffer, char *format, ...) ++{ ++ int retval; ++ va_list args; ++ ++ va_start(args, format); ++ retval = vsprintf(buffer, format, args); ++ va_end(args); ++ return retval; ++} ++ ++int DWC_SNPRINTF(char *buffer, int size, char *format, ...) ++{ ++ int retval; ++ va_list args; ++ ++ va_start(args, format); ++ retval = vsnprintf(buffer, size, format, args); ++ va_end(args); ++ return retval; ++} ++ ++void __DWC_WARN(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++} ++ ++void __DWC_ERROR(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++} ++ ++void DWC_EXCEPTION(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++// BUG_ON(1); ??? ++} ++ ++#ifdef DEBUG ++void __DWC_DEBUG(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++} ++#endif ++ ++ ++/* dwc_mem.h */ ++ ++#if 0 ++dwc_pool_t *DWC_DMA_POOL_CREATE(uint32_t size, ++ uint32_t align, ++ uint32_t alloc) ++{ ++ struct dma_pool *pool = dma_pool_create("Pool", NULL, ++ size, align, alloc); ++ return (dwc_pool_t *)pool; ++} ++ ++void DWC_DMA_POOL_DESTROY(dwc_pool_t *pool) ++{ ++ dma_pool_destroy((struct dma_pool *)pool); ++} ++ ++void *DWC_DMA_POOL_ALLOC(dwc_pool_t *pool, uint64_t *dma_addr) ++{ ++// return dma_pool_alloc((struct dma_pool *)pool, GFP_KERNEL, dma_addr); ++ return dma_pool_alloc((struct dma_pool *)pool, M_WAITOK, dma_addr); ++} ++ ++void *DWC_DMA_POOL_ZALLOC(dwc_pool_t *pool, uint64_t *dma_addr) ++{ ++ void *vaddr = DWC_DMA_POOL_ALLOC(pool, dma_addr); ++ memset(..); ++} ++ ++void DWC_DMA_POOL_FREE(dwc_pool_t *pool, void *vaddr, void *daddr) ++{ ++ dma_pool_free(pool, vaddr, daddr); ++} ++#endif ++ ++static void dmamap_cb(void *arg, bus_dma_segment_t *segs, int nseg, int error) ++{ ++ if (error) ++ return; ++ *(bus_addr_t *)arg = segs[0].ds_addr; ++} ++ ++void *__DWC_DMA_ALLOC(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr) ++{ ++ dwc_dmactx_t *dma = (dwc_dmactx_t *)dma_ctx; ++ int error; ++ ++ error = bus_dma_tag_create( ++#if __FreeBSD_version >= 700000 ++ bus_get_dma_tag(dma->dev), /* parent */ ++#else ++ NULL, /* parent */ ++#endif ++ 4, 0, /* alignment, bounds */ ++ BUS_SPACE_MAXADDR_32BIT, /* lowaddr */ ++ BUS_SPACE_MAXADDR, /* highaddr */ ++ NULL, NULL, /* filter, filterarg */ ++ size, /* maxsize */ ++ 1, /* nsegments */ ++ size, /* maxsegsize */ ++ 0, /* flags */ ++ NULL, /* lockfunc */ ++ NULL, /* lockarg */ ++ &dma->dma_tag); ++ if (error) { ++ device_printf(dma->dev, "%s: bus_dma_tag_create failed: %d\n", ++ __func__, error); ++ goto fail_0; ++ } ++ ++ error = bus_dmamem_alloc(dma->dma_tag, &dma->dma_vaddr, ++ BUS_DMA_NOWAIT | BUS_DMA_COHERENT, &dma->dma_map); ++ if (error) { ++ device_printf(dma->dev, "%s: bus_dmamem_alloc(%ju) failed: %d\n", ++ __func__, (uintmax_t)size, error); ++ goto fail_1; ++ } ++ ++ dma->dma_paddr = 0; ++ error = bus_dmamap_load(dma->dma_tag, dma->dma_map, dma->dma_vaddr, size, ++ dmamap_cb, &dma->dma_paddr, BUS_DMA_NOWAIT); ++ if (error || dma->dma_paddr == 0) { ++ device_printf(dma->dev, "%s: bus_dmamap_load failed: %d\n", ++ __func__, error); ++ goto fail_2; ++ } ++ ++ *dma_addr = dma->dma_paddr; ++ return dma->dma_vaddr; ++ ++fail_2: ++ bus_dmamap_unload(dma->dma_tag, dma->dma_map); ++fail_1: ++ bus_dmamem_free(dma->dma_tag, dma->dma_vaddr, dma->dma_map); ++ bus_dma_tag_destroy(dma->dma_tag); ++fail_0: ++ dma->dma_map = NULL; ++ dma->dma_tag = NULL; ++ ++ return NULL; ++} ++ ++void __DWC_DMA_FREE(void *dma_ctx, uint32_t size, void *virt_addr, dwc_dma_t dma_addr) ++{ ++ dwc_dmactx_t *dma = (dwc_dmactx_t *)dma_ctx; ++ ++ if (dma->dma_tag == NULL) ++ return; ++ if (dma->dma_map != NULL) { ++ bus_dmamap_sync(dma->dma_tag, dma->dma_map, ++ BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE); ++ bus_dmamap_unload(dma->dma_tag, dma->dma_map); ++ bus_dmamem_free(dma->dma_tag, dma->dma_vaddr, dma->dma_map); ++ dma->dma_map = NULL; ++ } ++ ++ bus_dma_tag_destroy(dma->dma_tag); ++ dma->dma_tag = NULL; ++} ++ ++void *__DWC_ALLOC(void *mem_ctx, uint32_t size) ++{ ++ return malloc(size, M_DEVBUF, M_WAITOK | M_ZERO); ++} ++ ++void *__DWC_ALLOC_ATOMIC(void *mem_ctx, uint32_t size) ++{ ++ return malloc(size, M_DEVBUF, M_NOWAIT | M_ZERO); ++} ++ ++void __DWC_FREE(void *mem_ctx, void *addr) ++{ ++ free(addr, M_DEVBUF); ++} ++ ++ ++#ifdef DWC_CRYPTOLIB ++/* dwc_crypto.h */ ++ ++void DWC_RANDOM_BYTES(uint8_t *buffer, uint32_t length) ++{ ++ get_random_bytes(buffer, length); ++} ++ ++int DWC_AES_CBC(uint8_t *message, uint32_t messagelen, uint8_t *key, uint32_t keylen, uint8_t iv[16], uint8_t *out) ++{ ++ struct crypto_blkcipher *tfm; ++ struct blkcipher_desc desc; ++ struct scatterlist sgd; ++ struct scatterlist sgs; ++ ++ tfm = crypto_alloc_blkcipher("cbc(aes)", 0, CRYPTO_ALG_ASYNC); ++ if (tfm == NULL) { ++ printk("failed to load transform for aes CBC\n"); ++ return -1; ++ } ++ ++ crypto_blkcipher_setkey(tfm, key, keylen); ++ crypto_blkcipher_set_iv(tfm, iv, 16); ++ ++ sg_init_one(&sgd, out, messagelen); ++ sg_init_one(&sgs, message, messagelen); ++ ++ desc.tfm = tfm; ++ desc.flags = 0; ++ ++ if (crypto_blkcipher_encrypt(&desc, &sgd, &sgs, messagelen)) { ++ crypto_free_blkcipher(tfm); ++ DWC_ERROR("AES CBC encryption failed"); ++ return -1; ++ } ++ ++ crypto_free_blkcipher(tfm); ++ return 0; ++} ++ ++int DWC_SHA256(uint8_t *message, uint32_t len, uint8_t *out) ++{ ++ struct crypto_hash *tfm; ++ struct hash_desc desc; ++ struct scatterlist sg; ++ ++ tfm = crypto_alloc_hash("sha256", 0, CRYPTO_ALG_ASYNC); ++ if (IS_ERR(tfm)) { ++ DWC_ERROR("Failed to load transform for sha256: %ld", PTR_ERR(tfm)); ++ return 0; ++ } ++ desc.tfm = tfm; ++ desc.flags = 0; ++ ++ sg_init_one(&sg, message, len); ++ crypto_hash_digest(&desc, &sg, len, out); ++ crypto_free_hash(tfm); ++ ++ return 1; ++} ++ ++int DWC_HMAC_SHA256(uint8_t *message, uint32_t messagelen, ++ uint8_t *key, uint32_t keylen, uint8_t *out) ++{ ++ struct crypto_hash *tfm; ++ struct hash_desc desc; ++ struct scatterlist sg; ++ ++ tfm = crypto_alloc_hash("hmac(sha256)", 0, CRYPTO_ALG_ASYNC); ++ if (IS_ERR(tfm)) { ++ DWC_ERROR("Failed to load transform for hmac(sha256): %ld", PTR_ERR(tfm)); ++ return 0; ++ } ++ desc.tfm = tfm; ++ desc.flags = 0; ++ ++ sg_init_one(&sg, message, messagelen); ++ crypto_hash_setkey(tfm, key, keylen); ++ crypto_hash_digest(&desc, &sg, messagelen, out); ++ crypto_free_hash(tfm); ++ ++ return 1; ++} ++ ++#endif /* DWC_CRYPTOLIB */ ++ ++ ++/* Byte Ordering Conversions */ ++ ++uint32_t DWC_CPU_TO_LE32(uint32_t *p) ++{ ++#ifdef __LITTLE_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ ++ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24)); ++#endif ++} ++ ++uint32_t DWC_CPU_TO_BE32(uint32_t *p) ++{ ++#ifdef __BIG_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ ++ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24)); ++#endif ++} ++ ++uint32_t DWC_LE32_TO_CPU(uint32_t *p) ++{ ++#ifdef __LITTLE_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ ++ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24)); ++#endif ++} ++ ++uint32_t DWC_BE32_TO_CPU(uint32_t *p) ++{ ++#ifdef __BIG_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ ++ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24)); ++#endif ++} ++ ++uint16_t DWC_CPU_TO_LE16(uint16_t *p) ++{ ++#ifdef __LITTLE_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ return (u_p[1] | (u_p[0] << 8)); ++#endif ++} ++ ++uint16_t DWC_CPU_TO_BE16(uint16_t *p) ++{ ++#ifdef __BIG_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ return (u_p[1] | (u_p[0] << 8)); ++#endif ++} ++ ++uint16_t DWC_LE16_TO_CPU(uint16_t *p) ++{ ++#ifdef __LITTLE_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ return (u_p[1] | (u_p[0] << 8)); ++#endif ++} ++ ++uint16_t DWC_BE16_TO_CPU(uint16_t *p) ++{ ++#ifdef __BIG_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ return (u_p[1] | (u_p[0] << 8)); ++#endif ++} ++ ++ ++/* Registers */ ++ ++uint32_t DWC_READ_REG32(void *io_ctx, uint32_t volatile *reg) ++{ ++ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx; ++ bus_size_t ior = (bus_size_t)reg; ++ ++ return bus_space_read_4(io->iot, io->ioh, ior); ++} ++ ++#if 0 ++uint64_t DWC_READ_REG64(void *io_ctx, uint64_t volatile *reg) ++{ ++ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx; ++ bus_size_t ior = (bus_size_t)reg; ++ ++ return bus_space_read_8(io->iot, io->ioh, ior); ++} ++#endif ++ ++void DWC_WRITE_REG32(void *io_ctx, uint32_t volatile *reg, uint32_t value) ++{ ++ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx; ++ bus_size_t ior = (bus_size_t)reg; ++ ++ bus_space_write_4(io->iot, io->ioh, ior, value); ++} ++ ++#if 0 ++void DWC_WRITE_REG64(void *io_ctx, uint64_t volatile *reg, uint64_t value) ++{ ++ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx; ++ bus_size_t ior = (bus_size_t)reg; ++ ++ bus_space_write_8(io->iot, io->ioh, ior, value); ++} ++#endif ++ ++void DWC_MODIFY_REG32(void *io_ctx, uint32_t volatile *reg, uint32_t clear_mask, ++ uint32_t set_mask) ++{ ++ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx; ++ bus_size_t ior = (bus_size_t)reg; ++ ++ bus_space_write_4(io->iot, io->ioh, ior, ++ (bus_space_read_4(io->iot, io->ioh, ior) & ++ ~clear_mask) | set_mask); ++} ++ ++#if 0 ++void DWC_MODIFY_REG64(void *io_ctx, uint64_t volatile *reg, uint64_t clear_mask, ++ uint64_t set_mask) ++{ ++ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx; ++ bus_size_t ior = (bus_size_t)reg; ++ ++ bus_space_write_8(io->iot, io->ioh, ior, ++ (bus_space_read_8(io->iot, io->ioh, ior) & ++ ~clear_mask) | set_mask); ++} ++#endif ++ ++ ++/* Locking */ ++ ++dwc_spinlock_t *DWC_SPINLOCK_ALLOC(void) ++{ ++ struct mtx *sl = DWC_ALLOC(sizeof(*sl)); ++ ++ if (!sl) { ++ DWC_ERROR("Cannot allocate memory for spinlock"); ++ return NULL; ++ } ++ ++ mtx_init(sl, "dw3spn", NULL, MTX_SPIN); ++ return (dwc_spinlock_t *)sl; ++} ++ ++void DWC_SPINLOCK_FREE(dwc_spinlock_t *lock) ++{ ++ struct mtx *sl = (struct mtx *)lock; ++ ++ mtx_destroy(sl); ++ DWC_FREE(sl); ++} ++ ++void DWC_SPINLOCK(dwc_spinlock_t *lock) ++{ ++ mtx_lock_spin((struct mtx *)lock); // ??? ++} ++ ++void DWC_SPINUNLOCK(dwc_spinlock_t *lock) ++{ ++ mtx_unlock_spin((struct mtx *)lock); // ??? ++} ++ ++void DWC_SPINLOCK_IRQSAVE(dwc_spinlock_t *lock, dwc_irqflags_t *flags) ++{ ++ mtx_lock_spin((struct mtx *)lock); ++} ++ ++void DWC_SPINUNLOCK_IRQRESTORE(dwc_spinlock_t *lock, dwc_irqflags_t flags) ++{ ++ mtx_unlock_spin((struct mtx *)lock); ++} ++ ++dwc_mutex_t *DWC_MUTEX_ALLOC(void) ++{ ++ struct mtx *m; ++ dwc_mutex_t *mutex = (dwc_mutex_t *)DWC_ALLOC(sizeof(struct mtx)); ++ ++ if (!mutex) { ++ DWC_ERROR("Cannot allocate memory for mutex"); ++ return NULL; ++ } ++ ++ m = (struct mtx *)mutex; ++ mtx_init(m, "dw3mtx", NULL, MTX_DEF); ++ return mutex; ++} ++ ++#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES)) ++#else ++void DWC_MUTEX_FREE(dwc_mutex_t *mutex) ++{ ++ mtx_destroy((struct mtx *)mutex); ++ DWC_FREE(mutex); ++} ++#endif ++ ++void DWC_MUTEX_LOCK(dwc_mutex_t *mutex) ++{ ++ struct mtx *m = (struct mtx *)mutex; ++ ++ mtx_lock(m); ++} ++ ++int DWC_MUTEX_TRYLOCK(dwc_mutex_t *mutex) ++{ ++ struct mtx *m = (struct mtx *)mutex; ++ ++ return mtx_trylock(m); ++} ++ ++void DWC_MUTEX_UNLOCK(dwc_mutex_t *mutex) ++{ ++ struct mtx *m = (struct mtx *)mutex; ++ ++ mtx_unlock(m); ++} ++ ++ ++/* Timing */ ++ ++void DWC_UDELAY(uint32_t usecs) ++{ ++ DELAY(usecs); ++} ++ ++void DWC_MDELAY(uint32_t msecs) ++{ ++ do { ++ DELAY(1000); ++ } while (--msecs); ++} ++ ++void DWC_MSLEEP(uint32_t msecs) ++{ ++ struct timeval tv; ++ ++ tv.tv_sec = msecs / 1000; ++ tv.tv_usec = (msecs - tv.tv_sec * 1000) * 1000; ++ pause("dw3slp", tvtohz(&tv)); ++} ++ ++uint32_t DWC_TIME(void) ++{ ++ struct timeval tv; ++ ++ microuptime(&tv); // or getmicrouptime? (less precise, but faster) ++ return tv.tv_sec * 1000 + tv.tv_usec / 1000; ++} ++ ++ ++/* Timers */ ++ ++struct dwc_timer { ++ struct callout t; ++ char *name; ++ dwc_spinlock_t *lock; ++ dwc_timer_callback_t cb; ++ void *data; ++}; ++ ++dwc_timer_t *DWC_TIMER_ALLOC(char *name, dwc_timer_callback_t cb, void *data) ++{ ++ dwc_timer_t *t = DWC_ALLOC(sizeof(*t)); ++ ++ if (!t) { ++ DWC_ERROR("Cannot allocate memory for timer"); ++ return NULL; ++ } ++ ++ callout_init(&t->t, 1); ++ ++ t->name = DWC_STRDUP(name); ++ if (!t->name) { ++ DWC_ERROR("Cannot allocate memory for timer->name"); ++ goto no_name; ++ } ++ ++ t->lock = DWC_SPINLOCK_ALLOC(); ++ if (!t->lock) { ++ DWC_ERROR("Cannot allocate memory for lock"); ++ goto no_lock; ++ } ++ ++ t->cb = cb; ++ t->data = data; ++ ++ return t; ++ ++ no_lock: ++ DWC_FREE(t->name); ++ no_name: ++ DWC_FREE(t); ++ ++ return NULL; ++} ++ ++void DWC_TIMER_FREE(dwc_timer_t *timer) ++{ ++ callout_stop(&timer->t); ++ DWC_SPINLOCK_FREE(timer->lock); ++ DWC_FREE(timer->name); ++ DWC_FREE(timer); ++} ++ ++void DWC_TIMER_SCHEDULE(dwc_timer_t *timer, uint32_t time) ++{ ++ struct timeval tv; ++ ++ tv.tv_sec = time / 1000; ++ tv.tv_usec = (time - tv.tv_sec * 1000) * 1000; ++ callout_reset(&timer->t, tvtohz(&tv), timer->cb, timer->data); ++} ++ ++void DWC_TIMER_CANCEL(dwc_timer_t *timer) ++{ ++ callout_stop(&timer->t); ++} ++ ++ ++/* Wait Queues */ ++ ++struct dwc_waitq { ++ struct mtx lock; ++ int abort; ++}; ++ ++dwc_waitq_t *DWC_WAITQ_ALLOC(void) ++{ ++ dwc_waitq_t *wq = DWC_ALLOC(sizeof(*wq)); ++ ++ if (!wq) { ++ DWC_ERROR("Cannot allocate memory for waitqueue"); ++ return NULL; ++ } ++ ++ mtx_init(&wq->lock, "dw3wtq", NULL, MTX_DEF); ++ wq->abort = 0; ++ ++ return wq; ++} ++ ++void DWC_WAITQ_FREE(dwc_waitq_t *wq) ++{ ++ mtx_destroy(&wq->lock); ++ DWC_FREE(wq); ++} ++ ++int32_t DWC_WAITQ_WAIT(dwc_waitq_t *wq, dwc_waitq_condition_t cond, void *data) ++{ ++// intrmask_t ipl; ++ int result = 0; ++ ++ mtx_lock(&wq->lock); ++// ipl = splbio(); ++ ++ /* Skip the sleep if already aborted or triggered */ ++ if (!wq->abort && !cond(data)) { ++// splx(ipl); ++ result = msleep(wq, &wq->lock, PCATCH, "dw3wat", 0); // infinite timeout ++// ipl = splbio(); ++ } ++ ++ if (result == ERESTART) { // signaled - restart ++ result = -DWC_E_RESTART; ++ ++ } else if (result == EINTR) { // signaled - interrupt ++ result = -DWC_E_ABORT; ++ ++ } else if (wq->abort) { ++ result = -DWC_E_ABORT; ++ ++ } else { ++ result = 0; ++ } ++ ++ wq->abort = 0; ++// splx(ipl); ++ mtx_unlock(&wq->lock); ++ return result; ++} ++ ++int32_t DWC_WAITQ_WAIT_TIMEOUT(dwc_waitq_t *wq, dwc_waitq_condition_t cond, ++ void *data, int32_t msecs) ++{ ++ struct timeval tv, tv1, tv2; ++// intrmask_t ipl; ++ int result = 0; ++ ++ tv.tv_sec = msecs / 1000; ++ tv.tv_usec = (msecs - tv.tv_sec * 1000) * 1000; ++ ++ mtx_lock(&wq->lock); ++// ipl = splbio(); ++ ++ /* Skip the sleep if already aborted or triggered */ ++ if (!wq->abort && !cond(data)) { ++// splx(ipl); ++ getmicrouptime(&tv1); ++ result = msleep(wq, &wq->lock, PCATCH, "dw3wto", tvtohz(&tv)); ++ getmicrouptime(&tv2); ++// ipl = splbio(); ++ } ++ ++ if (result == 0) { // awoken ++ if (wq->abort) { ++ result = -DWC_E_ABORT; ++ } else { ++ tv2.tv_usec -= tv1.tv_usec; ++ if (tv2.tv_usec < 0) { ++ tv2.tv_usec += 1000000; ++ tv2.tv_sec--; ++ } ++ ++ tv2.tv_sec -= tv1.tv_sec; ++ result = tv2.tv_sec * 1000 + tv2.tv_usec / 1000; ++ result = msecs - result; ++ if (result <= 0) ++ result = 1; ++ } ++ } else if (result == ERESTART) { // signaled - restart ++ result = -DWC_E_RESTART; ++ ++ } else if (result == EINTR) { // signaled - interrupt ++ result = -DWC_E_ABORT; ++ ++ } else { // timed out ++ result = -DWC_E_TIMEOUT; ++ } ++ ++ wq->abort = 0; ++// splx(ipl); ++ mtx_unlock(&wq->lock); ++ return result; ++} ++ ++void DWC_WAITQ_TRIGGER(dwc_waitq_t *wq) ++{ ++ wakeup(wq); ++} ++ ++void DWC_WAITQ_ABORT(dwc_waitq_t *wq) ++{ ++// intrmask_t ipl; ++ ++ mtx_lock(&wq->lock); ++// ipl = splbio(); ++ wq->abort = 1; ++ wakeup(wq); ++// splx(ipl); ++ mtx_unlock(&wq->lock); ++} ++ ++ ++/* Threading */ ++ ++struct dwc_thread { ++ struct proc *proc; ++ int abort; ++}; ++ ++dwc_thread_t *DWC_THREAD_RUN(dwc_thread_function_t func, char *name, void *data) ++{ ++ int retval; ++ dwc_thread_t *thread = DWC_ALLOC(sizeof(*thread)); ++ ++ if (!thread) { ++ return NULL; ++ } ++ ++ thread->abort = 0; ++ retval = kthread_create((void (*)(void *))func, data, &thread->proc, ++ RFPROC | RFNOWAIT, 0, "%s", name); ++ if (retval) { ++ DWC_FREE(thread); ++ return NULL; ++ } ++ ++ return thread; ++} ++ ++int DWC_THREAD_STOP(dwc_thread_t *thread) ++{ ++ int retval; ++ ++ thread->abort = 1; ++ retval = tsleep(&thread->abort, 0, "dw3stp", 60 * hz); ++ ++ if (retval == 0) { ++ /* DWC_THREAD_EXIT() will free the thread struct */ ++ return 0; ++ } ++ ++ /* NOTE: We leak the thread struct if thread doesn't die */ ++ ++ if (retval == EWOULDBLOCK) { ++ return -DWC_E_TIMEOUT; ++ } ++ ++ return -DWC_E_UNKNOWN; ++} ++ ++dwc_bool_t DWC_THREAD_SHOULD_STOP(dwc_thread_t *thread) ++{ ++ return thread->abort; ++} ++ ++void DWC_THREAD_EXIT(dwc_thread_t *thread) ++{ ++ wakeup(&thread->abort); ++ DWC_FREE(thread); ++ kthread_exit(0); ++} ++ ++ ++/* tasklets ++ - Runs in interrupt context (cannot sleep) ++ - Each tasklet runs on a single CPU [ How can we ensure this on FreeBSD? Does it matter? ] ++ - Different tasklets can be running simultaneously on different CPUs [ shouldn't matter ] ++ */ ++struct dwc_tasklet { ++ struct task t; ++ dwc_tasklet_callback_t cb; ++ void *data; ++}; ++ ++static void tasklet_callback(void *data, int pending) // what to do with pending ??? ++{ ++ dwc_tasklet_t *task = (dwc_tasklet_t *)data; ++ ++ task->cb(task->data); ++} ++ ++dwc_tasklet_t *DWC_TASK_ALLOC(char *name, dwc_tasklet_callback_t cb, void *data) ++{ ++ dwc_tasklet_t *task = DWC_ALLOC(sizeof(*task)); ++ ++ if (task) { ++ task->cb = cb; ++ task->data = data; ++ TASK_INIT(&task->t, 0, tasklet_callback, task); ++ } else { ++ DWC_ERROR("Cannot allocate memory for tasklet"); ++ } ++ ++ return task; ++} ++ ++void DWC_TASK_FREE(dwc_tasklet_t *task) ++{ ++ taskqueue_drain(taskqueue_fast, &task->t); // ??? ++ DWC_FREE(task); ++} ++ ++void DWC_TASK_SCHEDULE(dwc_tasklet_t *task) ++{ ++ /* Uses predefined system queue */ ++ taskqueue_enqueue_fast(taskqueue_fast, &task->t); ++} ++ ++ ++/* workqueues ++ - Runs in process context (can sleep) ++ */ ++typedef struct work_container { ++ dwc_work_callback_t cb; ++ void *data; ++ dwc_workq_t *wq; ++ char *name; ++ int hz; ++ ++#ifdef DEBUG ++ DWC_CIRCLEQ_ENTRY(work_container) entry; ++#endif ++ struct task task; ++} work_container_t; ++ ++#ifdef DEBUG ++DWC_CIRCLEQ_HEAD(work_container_queue, work_container); ++#endif ++ ++struct dwc_workq { ++ struct taskqueue *taskq; ++ dwc_spinlock_t *lock; ++ dwc_waitq_t *waitq; ++ int pending; ++ ++#ifdef DEBUG ++ struct work_container_queue entries; ++#endif ++}; ++ ++static void do_work(void *data, int pending) // what to do with pending ??? ++{ ++ work_container_t *container = (work_container_t *)data; ++ dwc_workq_t *wq = container->wq; ++ dwc_irqflags_t flags; ++ ++ if (container->hz) { ++ pause("dw3wrk", container->hz); ++ } ++ ++ container->cb(container->data); ++ DWC_DEBUG("Work done: %s, container=%p", container->name, container); ++ ++ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags); ++ ++#ifdef DEBUG ++ DWC_CIRCLEQ_REMOVE(&wq->entries, container, entry); ++#endif ++ if (container->name) ++ DWC_FREE(container->name); ++ DWC_FREE(container); ++ wq->pending--; ++ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags); ++ DWC_WAITQ_TRIGGER(wq->waitq); ++} ++ ++static int work_done(void *data) ++{ ++ dwc_workq_t *workq = (dwc_workq_t *)data; ++ ++ return workq->pending == 0; ++} ++ ++int DWC_WORKQ_WAIT_WORK_DONE(dwc_workq_t *workq, int timeout) ++{ ++ return DWC_WAITQ_WAIT_TIMEOUT(workq->waitq, work_done, workq, timeout); ++} ++ ++dwc_workq_t *DWC_WORKQ_ALLOC(char *name) ++{ ++ dwc_workq_t *wq = DWC_ALLOC(sizeof(*wq)); ++ ++ if (!wq) { ++ DWC_ERROR("Cannot allocate memory for workqueue"); ++ return NULL; ++ } ++ ++ wq->taskq = taskqueue_create(name, M_NOWAIT, taskqueue_thread_enqueue, &wq->taskq); ++ if (!wq->taskq) { ++ DWC_ERROR("Cannot allocate memory for taskqueue"); ++ goto no_taskq; ++ } ++ ++ wq->pending = 0; ++ ++ wq->lock = DWC_SPINLOCK_ALLOC(); ++ if (!wq->lock) { ++ DWC_ERROR("Cannot allocate memory for spinlock"); ++ goto no_lock; ++ } ++ ++ wq->waitq = DWC_WAITQ_ALLOC(); ++ if (!wq->waitq) { ++ DWC_ERROR("Cannot allocate memory for waitqueue"); ++ goto no_waitq; ++ } ++ ++ taskqueue_start_threads(&wq->taskq, 1, PWAIT, "%s taskq", "dw3tsk"); ++ ++#ifdef DEBUG ++ DWC_CIRCLEQ_INIT(&wq->entries); ++#endif ++ return wq; ++ ++ no_waitq: ++ DWC_SPINLOCK_FREE(wq->lock); ++ no_lock: ++ taskqueue_free(wq->taskq); ++ no_taskq: ++ DWC_FREE(wq); ++ ++ return NULL; ++} ++ ++void DWC_WORKQ_FREE(dwc_workq_t *wq) ++{ ++#ifdef DEBUG ++ dwc_irqflags_t flags; ++ ++ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags); ++ ++ if (wq->pending != 0) { ++ struct work_container *container; ++ ++ DWC_ERROR("Destroying work queue with pending work"); ++ ++ DWC_CIRCLEQ_FOREACH(container, &wq->entries, entry) { ++ DWC_ERROR("Work %s still pending", container->name); ++ } ++ } ++ ++ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags); ++#endif ++ DWC_WAITQ_FREE(wq->waitq); ++ DWC_SPINLOCK_FREE(wq->lock); ++ taskqueue_free(wq->taskq); ++ DWC_FREE(wq); ++} ++ ++void DWC_WORKQ_SCHEDULE(dwc_workq_t *wq, dwc_work_callback_t cb, void *data, ++ char *format, ...) ++{ ++ dwc_irqflags_t flags; ++ work_container_t *container; ++ static char name[128]; ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VSNPRINTF(name, 128, format, args); ++ va_end(args); ++ ++ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags); ++ wq->pending++; ++ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags); ++ DWC_WAITQ_TRIGGER(wq->waitq); ++ ++ container = DWC_ALLOC_ATOMIC(sizeof(*container)); ++ if (!container) { ++ DWC_ERROR("Cannot allocate memory for container"); ++ return; ++ } ++ ++ container->name = DWC_STRDUP(name); ++ if (!container->name) { ++ DWC_ERROR("Cannot allocate memory for container->name"); ++ DWC_FREE(container); ++ return; ++ } ++ ++ container->cb = cb; ++ container->data = data; ++ container->wq = wq; ++ container->hz = 0; ++ ++ DWC_DEBUG("Queueing work: %s, container=%p", container->name, container); ++ ++ TASK_INIT(&container->task, 0, do_work, container); ++ ++#ifdef DEBUG ++ DWC_CIRCLEQ_INSERT_TAIL(&wq->entries, container, entry); ++#endif ++ taskqueue_enqueue_fast(wq->taskq, &container->task); ++} ++ ++void DWC_WORKQ_SCHEDULE_DELAYED(dwc_workq_t *wq, dwc_work_callback_t cb, ++ void *data, uint32_t time, char *format, ...) ++{ ++ dwc_irqflags_t flags; ++ work_container_t *container; ++ static char name[128]; ++ struct timeval tv; ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VSNPRINTF(name, 128, format, args); ++ va_end(args); ++ ++ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags); ++ wq->pending++; ++ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags); ++ DWC_WAITQ_TRIGGER(wq->waitq); ++ ++ container = DWC_ALLOC_ATOMIC(sizeof(*container)); ++ if (!container) { ++ DWC_ERROR("Cannot allocate memory for container"); ++ return; ++ } ++ ++ container->name = DWC_STRDUP(name); ++ if (!container->name) { ++ DWC_ERROR("Cannot allocate memory for container->name"); ++ DWC_FREE(container); ++ return; ++ } ++ ++ container->cb = cb; ++ container->data = data; ++ container->wq = wq; ++ ++ tv.tv_sec = time / 1000; ++ tv.tv_usec = (time - tv.tv_sec * 1000) * 1000; ++ container->hz = tvtohz(&tv); ++ ++ DWC_DEBUG("Queueing work: %s, container=%p", container->name, container); ++ ++ TASK_INIT(&container->task, 0, do_work, container); ++ ++#ifdef DEBUG ++ DWC_CIRCLEQ_INSERT_TAIL(&wq->entries, container, entry); ++#endif ++ taskqueue_enqueue_fast(wq->taskq, &container->task); ++} ++ ++int DWC_WORKQ_PENDING(dwc_workq_t *wq) ++{ ++ return wq->pending; ++} +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_common_linux.c +@@ -0,0 +1,1409 @@ ++#include ++#include ++#include ++#include ++ ++#ifdef DWC_CCLIB ++# include "dwc_cc.h" ++#endif ++ ++#ifdef DWC_CRYPTOLIB ++# include "dwc_modpow.h" ++# include "dwc_dh.h" ++# include "dwc_crypto.h" ++#endif ++ ++#ifdef DWC_NOTIFYLIB ++# include "dwc_notifier.h" ++#endif ++ ++/* OS-Level Implementations */ ++ ++/* This is the Linux kernel implementation of the DWC platform library. */ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++ ++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,24) ++# include ++#else ++# include ++#endif ++ ++#include ++#include ++#include ++#include ++ ++#include "dwc_os.h" ++#include "dwc_list.h" ++ ++ ++/* MISC */ ++ ++void *DWC_MEMSET(void *dest, uint8_t byte, uint32_t size) ++{ ++ return memset(dest, byte, size); ++} ++ ++void *DWC_MEMCPY(void *dest, void const *src, uint32_t size) ++{ ++ return memcpy(dest, src, size); ++} ++ ++void *DWC_MEMMOVE(void *dest, void *src, uint32_t size) ++{ ++ return memmove(dest, src, size); ++} ++ ++int DWC_MEMCMP(void *m1, void *m2, uint32_t size) ++{ ++ return memcmp(m1, m2, size); ++} ++ ++int DWC_STRNCMP(void *s1, void *s2, uint32_t size) ++{ ++ return strncmp(s1, s2, size); ++} ++ ++int DWC_STRCMP(void *s1, void *s2) ++{ ++ return strcmp(s1, s2); ++} ++ ++int DWC_STRLEN(char const *str) ++{ ++ return strlen(str); ++} ++ ++char *DWC_STRCPY(char *to, char const *from) ++{ ++ return strcpy(to, from); ++} ++ ++char *DWC_STRDUP(char const *str) ++{ ++ int len = DWC_STRLEN(str) + 1; ++ char *new = DWC_ALLOC_ATOMIC(len); ++ ++ if (!new) { ++ return NULL; ++ } ++ ++ DWC_MEMCPY(new, str, len); ++ return new; ++} ++ ++int DWC_ATOI(const char *str, int32_t *value) ++{ ++ char *end = NULL; ++ ++ *value = simple_strtol(str, &end, 0); ++ if (*end == '\0') { ++ return 0; ++ } ++ ++ return -1; ++} ++ ++int DWC_ATOUI(const char *str, uint32_t *value) ++{ ++ char *end = NULL; ++ ++ *value = simple_strtoul(str, &end, 0); ++ if (*end == '\0') { ++ return 0; ++ } ++ ++ return -1; ++} ++ ++ ++#ifdef DWC_UTFLIB ++/* From usbstring.c */ ++ ++int DWC_UTF8_TO_UTF16LE(uint8_t const *s, uint16_t *cp, unsigned len) ++{ ++ int count = 0; ++ u8 c; ++ u16 uchar; ++ ++ /* this insists on correct encodings, though not minimal ones. ++ * BUT it currently rejects legit 4-byte UTF-8 code points, ++ * which need surrogate pairs. (Unicode 3.1 can use them.) ++ */ ++ while (len != 0 && (c = (u8) *s++) != 0) { ++ if (unlikely(c & 0x80)) { ++ // 2-byte sequence: ++ // 00000yyyyyxxxxxx = 110yyyyy 10xxxxxx ++ if ((c & 0xe0) == 0xc0) { ++ uchar = (c & 0x1f) << 6; ++ ++ c = (u8) *s++; ++ if ((c & 0xc0) != 0xc0) ++ goto fail; ++ c &= 0x3f; ++ uchar |= c; ++ ++ // 3-byte sequence (most CJKV characters): ++ // zzzzyyyyyyxxxxxx = 1110zzzz 10yyyyyy 10xxxxxx ++ } else if ((c & 0xf0) == 0xe0) { ++ uchar = (c & 0x0f) << 12; ++ ++ c = (u8) *s++; ++ if ((c & 0xc0) != 0xc0) ++ goto fail; ++ c &= 0x3f; ++ uchar |= c << 6; ++ ++ c = (u8) *s++; ++ if ((c & 0xc0) != 0xc0) ++ goto fail; ++ c &= 0x3f; ++ uchar |= c; ++ ++ /* no bogus surrogates */ ++ if (0xd800 <= uchar && uchar <= 0xdfff) ++ goto fail; ++ ++ // 4-byte sequence (surrogate pairs, currently rare): ++ // 11101110wwwwzzzzyy + 110111yyyyxxxxxx ++ // = 11110uuu 10uuzzzz 10yyyyyy 10xxxxxx ++ // (uuuuu = wwww + 1) ++ // FIXME accept the surrogate code points (only) ++ } else ++ goto fail; ++ } else ++ uchar = c; ++ put_unaligned (cpu_to_le16 (uchar), cp++); ++ count++; ++ len--; ++ } ++ return count; ++fail: ++ return -1; ++} ++#endif /* DWC_UTFLIB */ ++ ++ ++/* dwc_debug.h */ ++ ++dwc_bool_t DWC_IN_IRQ(void) ++{ ++ return in_irq(); ++} ++ ++dwc_bool_t DWC_IN_BH(void) ++{ ++ return in_softirq(); ++} ++ ++void DWC_VPRINTF(char *format, va_list args) ++{ ++ vprintk(format, args); ++} ++ ++int DWC_VSNPRINTF(char *str, int size, char *format, va_list args) ++{ ++ return vsnprintf(str, size, format, args); ++} ++ ++void DWC_PRINTF(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++} ++ ++int DWC_SPRINTF(char *buffer, char *format, ...) ++{ ++ int retval; ++ va_list args; ++ ++ va_start(args, format); ++ retval = vsprintf(buffer, format, args); ++ va_end(args); ++ return retval; ++} ++ ++int DWC_SNPRINTF(char *buffer, int size, char *format, ...) ++{ ++ int retval; ++ va_list args; ++ ++ va_start(args, format); ++ retval = vsnprintf(buffer, size, format, args); ++ va_end(args); ++ return retval; ++} ++ ++void __DWC_WARN(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_PRINTF(KERN_WARNING); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++} ++ ++void __DWC_ERROR(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_PRINTF(KERN_ERR); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++} ++ ++void DWC_EXCEPTION(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_PRINTF(KERN_ERR); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++ BUG_ON(1); ++} ++ ++#ifdef DEBUG ++void __DWC_DEBUG(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_PRINTF(KERN_DEBUG); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++} ++#endif ++ ++ ++/* dwc_mem.h */ ++ ++#if 0 ++dwc_pool_t *DWC_DMA_POOL_CREATE(uint32_t size, ++ uint32_t align, ++ uint32_t alloc) ++{ ++ struct dma_pool *pool = dma_pool_create("Pool", NULL, ++ size, align, alloc); ++ return (dwc_pool_t *)pool; ++} ++ ++void DWC_DMA_POOL_DESTROY(dwc_pool_t *pool) ++{ ++ dma_pool_destroy((struct dma_pool *)pool); ++} ++ ++void *DWC_DMA_POOL_ALLOC(dwc_pool_t *pool, uint64_t *dma_addr) ++{ ++ return dma_pool_alloc((struct dma_pool *)pool, GFP_KERNEL, dma_addr); ++} ++ ++void *DWC_DMA_POOL_ZALLOC(dwc_pool_t *pool, uint64_t *dma_addr) ++{ ++ void *vaddr = DWC_DMA_POOL_ALLOC(pool, dma_addr); ++ memset(..); ++} ++ ++void DWC_DMA_POOL_FREE(dwc_pool_t *pool, void *vaddr, void *daddr) ++{ ++ dma_pool_free(pool, vaddr, daddr); ++} ++#endif ++ ++void *__DWC_DMA_ALLOC(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr) ++{ ++ return dma_alloc_coherent(dma_ctx, size, dma_addr, GFP_KERNEL | GFP_DMA32); ++} ++ ++void *__DWC_DMA_ALLOC_ATOMIC(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr) ++{ ++ return dma_alloc_coherent(dma_ctx, size, dma_addr, GFP_ATOMIC); ++} ++ ++void __DWC_DMA_FREE(void *dma_ctx, uint32_t size, void *virt_addr, dwc_dma_t dma_addr) ++{ ++ dma_free_coherent(dma_ctx, size, virt_addr, dma_addr); ++} ++ ++void *__DWC_ALLOC(void *mem_ctx, uint32_t size) ++{ ++ return kzalloc(size, GFP_KERNEL); ++} ++ ++void *__DWC_ALLOC_ATOMIC(void *mem_ctx, uint32_t size) ++{ ++ return kzalloc(size, GFP_ATOMIC); ++} ++ ++void __DWC_FREE(void *mem_ctx, void *addr) ++{ ++ kfree(addr); ++} ++ ++ ++#ifdef DWC_CRYPTOLIB ++/* dwc_crypto.h */ ++ ++void DWC_RANDOM_BYTES(uint8_t *buffer, uint32_t length) ++{ ++ get_random_bytes(buffer, length); ++} ++ ++int DWC_AES_CBC(uint8_t *message, uint32_t messagelen, uint8_t *key, uint32_t keylen, uint8_t iv[16], uint8_t *out) ++{ ++ struct crypto_blkcipher *tfm; ++ struct blkcipher_desc desc; ++ struct scatterlist sgd; ++ struct scatterlist sgs; ++ ++ tfm = crypto_alloc_blkcipher("cbc(aes)", 0, CRYPTO_ALG_ASYNC); ++ if (tfm == NULL) { ++ printk("failed to load transform for aes CBC\n"); ++ return -1; ++ } ++ ++ crypto_blkcipher_setkey(tfm, key, keylen); ++ crypto_blkcipher_set_iv(tfm, iv, 16); ++ ++ sg_init_one(&sgd, out, messagelen); ++ sg_init_one(&sgs, message, messagelen); ++ ++ desc.tfm = tfm; ++ desc.flags = 0; ++ ++ if (crypto_blkcipher_encrypt(&desc, &sgd, &sgs, messagelen)) { ++ crypto_free_blkcipher(tfm); ++ DWC_ERROR("AES CBC encryption failed"); ++ return -1; ++ } ++ ++ crypto_free_blkcipher(tfm); ++ return 0; ++} ++ ++int DWC_SHA256(uint8_t *message, uint32_t len, uint8_t *out) ++{ ++ struct crypto_hash *tfm; ++ struct hash_desc desc; ++ struct scatterlist sg; ++ ++ tfm = crypto_alloc_hash("sha256", 0, CRYPTO_ALG_ASYNC); ++ if (IS_ERR(tfm)) { ++ DWC_ERROR("Failed to load transform for sha256: %ld\n", PTR_ERR(tfm)); ++ return 0; ++ } ++ desc.tfm = tfm; ++ desc.flags = 0; ++ ++ sg_init_one(&sg, message, len); ++ crypto_hash_digest(&desc, &sg, len, out); ++ crypto_free_hash(tfm); ++ ++ return 1; ++} ++ ++int DWC_HMAC_SHA256(uint8_t *message, uint32_t messagelen, ++ uint8_t *key, uint32_t keylen, uint8_t *out) ++{ ++ struct crypto_hash *tfm; ++ struct hash_desc desc; ++ struct scatterlist sg; ++ ++ tfm = crypto_alloc_hash("hmac(sha256)", 0, CRYPTO_ALG_ASYNC); ++ if (IS_ERR(tfm)) { ++ DWC_ERROR("Failed to load transform for hmac(sha256): %ld\n", PTR_ERR(tfm)); ++ return 0; ++ } ++ desc.tfm = tfm; ++ desc.flags = 0; ++ ++ sg_init_one(&sg, message, messagelen); ++ crypto_hash_setkey(tfm, key, keylen); ++ crypto_hash_digest(&desc, &sg, messagelen, out); ++ crypto_free_hash(tfm); ++ ++ return 1; ++} ++#endif /* DWC_CRYPTOLIB */ ++ ++ ++/* Byte Ordering Conversions */ ++ ++uint32_t DWC_CPU_TO_LE32(uint32_t *p) ++{ ++#ifdef __LITTLE_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ ++ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24)); ++#endif ++} ++ ++uint32_t DWC_CPU_TO_BE32(uint32_t *p) ++{ ++#ifdef __BIG_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ ++ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24)); ++#endif ++} ++ ++uint32_t DWC_LE32_TO_CPU(uint32_t *p) ++{ ++#ifdef __LITTLE_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ ++ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24)); ++#endif ++} ++ ++uint32_t DWC_BE32_TO_CPU(uint32_t *p) ++{ ++#ifdef __BIG_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ ++ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24)); ++#endif ++} ++ ++uint16_t DWC_CPU_TO_LE16(uint16_t *p) ++{ ++#ifdef __LITTLE_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ return (u_p[1] | (u_p[0] << 8)); ++#endif ++} ++ ++uint16_t DWC_CPU_TO_BE16(uint16_t *p) ++{ ++#ifdef __BIG_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ return (u_p[1] | (u_p[0] << 8)); ++#endif ++} ++ ++uint16_t DWC_LE16_TO_CPU(uint16_t *p) ++{ ++#ifdef __LITTLE_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ return (u_p[1] | (u_p[0] << 8)); ++#endif ++} ++ ++uint16_t DWC_BE16_TO_CPU(uint16_t *p) ++{ ++#ifdef __BIG_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ return (u_p[1] | (u_p[0] << 8)); ++#endif ++} ++ ++ ++/* Registers */ ++ ++uint32_t DWC_READ_REG32(uint32_t volatile *reg) ++{ ++ return readl(reg); ++} ++ ++#if 0 ++uint64_t DWC_READ_REG64(uint64_t volatile *reg) ++{ ++} ++#endif ++ ++void DWC_WRITE_REG32(uint32_t volatile *reg, uint32_t value) ++{ ++ writel(value, reg); ++} ++ ++#if 0 ++void DWC_WRITE_REG64(uint64_t volatile *reg, uint64_t value) ++{ ++} ++#endif ++ ++void DWC_MODIFY_REG32(uint32_t volatile *reg, uint32_t clear_mask, uint32_t set_mask) ++{ ++ writel((readl(reg) & ~clear_mask) | set_mask, reg); ++} ++ ++#if 0 ++void DWC_MODIFY_REG64(uint64_t volatile *reg, uint64_t clear_mask, uint64_t set_mask) ++{ ++} ++#endif ++ ++ ++/* Locking */ ++ ++dwc_spinlock_t *DWC_SPINLOCK_ALLOC(void) ++{ ++ spinlock_t *sl = (spinlock_t *)1; ++ ++#if defined(CONFIG_PREEMPT) || defined(CONFIG_SMP) ++ sl = DWC_ALLOC(sizeof(*sl)); ++ if (!sl) { ++ DWC_ERROR("Cannot allocate memory for spinlock\n"); ++ return NULL; ++ } ++ ++ spin_lock_init(sl); ++#endif ++ return (dwc_spinlock_t *)sl; ++} ++ ++void DWC_SPINLOCK_FREE(dwc_spinlock_t *lock) ++{ ++#if defined(CONFIG_PREEMPT) || defined(CONFIG_SMP) ++ DWC_FREE(lock); ++#endif ++} ++ ++void DWC_SPINLOCK(dwc_spinlock_t *lock) ++{ ++#if defined(CONFIG_PREEMPT) || defined(CONFIG_SMP) ++ spin_lock((spinlock_t *)lock); ++#endif ++} ++ ++void DWC_SPINUNLOCK(dwc_spinlock_t *lock) ++{ ++#if defined(CONFIG_PREEMPT) || defined(CONFIG_SMP) ++ spin_unlock((spinlock_t *)lock); ++#endif ++} ++ ++void DWC_SPINLOCK_IRQSAVE(dwc_spinlock_t *lock, dwc_irqflags_t *flags) ++{ ++ dwc_irqflags_t f; ++ ++#if defined(CONFIG_PREEMPT) || defined(CONFIG_SMP) ++ spin_lock_irqsave((spinlock_t *)lock, f); ++#else ++ local_irq_save(f); ++#endif ++ *flags = f; ++} ++ ++void DWC_SPINUNLOCK_IRQRESTORE(dwc_spinlock_t *lock, dwc_irqflags_t flags) ++{ ++#if defined(CONFIG_PREEMPT) || defined(CONFIG_SMP) ++ spin_unlock_irqrestore((spinlock_t *)lock, flags); ++#else ++ local_irq_restore(flags); ++#endif ++} ++ ++dwc_mutex_t *DWC_MUTEX_ALLOC(void) ++{ ++ struct mutex *m; ++ dwc_mutex_t *mutex = (dwc_mutex_t *)DWC_ALLOC(sizeof(struct mutex)); ++ ++ if (!mutex) { ++ DWC_ERROR("Cannot allocate memory for mutex\n"); ++ return NULL; ++ } ++ ++ m = (struct mutex *)mutex; ++ mutex_init(m); ++ return mutex; ++} ++ ++#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES)) ++#else ++void DWC_MUTEX_FREE(dwc_mutex_t *mutex) ++{ ++ mutex_destroy((struct mutex *)mutex); ++ DWC_FREE(mutex); ++} ++#endif ++ ++void DWC_MUTEX_LOCK(dwc_mutex_t *mutex) ++{ ++ struct mutex *m = (struct mutex *)mutex; ++ mutex_lock(m); ++} ++ ++int DWC_MUTEX_TRYLOCK(dwc_mutex_t *mutex) ++{ ++ struct mutex *m = (struct mutex *)mutex; ++ return mutex_trylock(m); ++} ++ ++void DWC_MUTEX_UNLOCK(dwc_mutex_t *mutex) ++{ ++ struct mutex *m = (struct mutex *)mutex; ++ mutex_unlock(m); ++} ++ ++ ++/* Timing */ ++ ++void DWC_UDELAY(uint32_t usecs) ++{ ++ udelay(usecs); ++} ++ ++void DWC_MDELAY(uint32_t msecs) ++{ ++ mdelay(msecs); ++} ++ ++void DWC_MSLEEP(uint32_t msecs) ++{ ++ msleep(msecs); ++} ++ ++uint32_t DWC_TIME(void) ++{ ++ return jiffies_to_msecs(jiffies); ++} ++ ++ ++/* Timers */ ++ ++struct dwc_timer { ++ struct timer_list t; ++ char *name; ++ dwc_timer_callback_t cb; ++ void *data; ++ uint8_t scheduled; ++ dwc_spinlock_t *lock; ++}; ++ ++static void timer_callback(struct timer_list *tt) ++{ ++ dwc_timer_t *timer = from_timer(timer, tt, t); ++ dwc_irqflags_t flags; ++ ++ DWC_SPINLOCK_IRQSAVE(timer->lock, &flags); ++ timer->scheduled = 0; ++ DWC_SPINUNLOCK_IRQRESTORE(timer->lock, flags); ++ DWC_DEBUGC("Timer %s callback", timer->name); ++ timer->cb(timer->data); ++} ++ ++dwc_timer_t *DWC_TIMER_ALLOC(char *name, dwc_timer_callback_t cb, void *data) ++{ ++ dwc_timer_t *t = DWC_ALLOC(sizeof(*t)); ++ ++ if (!t) { ++ DWC_ERROR("Cannot allocate memory for timer"); ++ return NULL; ++ } ++ ++ t->name = DWC_STRDUP(name); ++ if (!t->name) { ++ DWC_ERROR("Cannot allocate memory for timer->name"); ++ goto no_name; ++ } ++ ++#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_SPINLOCK)) ++ DWC_SPINLOCK_ALLOC_LINUX_DEBUG(t->lock); ++#else ++ t->lock = DWC_SPINLOCK_ALLOC(); ++#endif ++ if (!t->lock) { ++ DWC_ERROR("Cannot allocate memory for lock"); ++ goto no_lock; ++ } ++ ++ t->scheduled = 0; ++ t->t.expires = jiffies; ++ timer_setup(&t->t, timer_callback, 0); ++ ++ t->cb = cb; ++ t->data = data; ++ ++ return t; ++ ++ no_lock: ++ DWC_FREE(t->name); ++ no_name: ++ DWC_FREE(t); ++ return NULL; ++} ++ ++void DWC_TIMER_FREE(dwc_timer_t *timer) ++{ ++ dwc_irqflags_t flags; ++ ++ DWC_SPINLOCK_IRQSAVE(timer->lock, &flags); ++ ++ if (timer->scheduled) { ++ del_timer(&timer->t); ++ timer->scheduled = 0; ++ } ++ ++ DWC_SPINUNLOCK_IRQRESTORE(timer->lock, flags); ++ DWC_SPINLOCK_FREE(timer->lock); ++ DWC_FREE(timer->name); ++ DWC_FREE(timer); ++} ++ ++void DWC_TIMER_SCHEDULE(dwc_timer_t *timer, uint32_t time) ++{ ++ dwc_irqflags_t flags; ++ ++ DWC_SPINLOCK_IRQSAVE(timer->lock, &flags); ++ ++ if (!timer->scheduled) { ++ timer->scheduled = 1; ++ DWC_DEBUGC("Scheduling timer %s to expire in +%d msec", timer->name, time); ++ timer->t.expires = jiffies + msecs_to_jiffies(time); ++ add_timer(&timer->t); ++ } else { ++ DWC_DEBUGC("Modifying timer %s to expire in +%d msec", timer->name, time); ++ mod_timer(&timer->t, jiffies + msecs_to_jiffies(time)); ++ } ++ ++ DWC_SPINUNLOCK_IRQRESTORE(timer->lock, flags); ++} ++ ++void DWC_TIMER_CANCEL(dwc_timer_t *timer) ++{ ++ del_timer(&timer->t); ++} ++ ++ ++/* Wait Queues */ ++ ++struct dwc_waitq { ++ wait_queue_head_t queue; ++ int abort; ++}; ++ ++dwc_waitq_t *DWC_WAITQ_ALLOC(void) ++{ ++ dwc_waitq_t *wq = DWC_ALLOC(sizeof(*wq)); ++ ++ if (!wq) { ++ DWC_ERROR("Cannot allocate memory for waitqueue\n"); ++ return NULL; ++ } ++ ++ init_waitqueue_head(&wq->queue); ++ wq->abort = 0; ++ return wq; ++} ++ ++void DWC_WAITQ_FREE(dwc_waitq_t *wq) ++{ ++ DWC_FREE(wq); ++} ++ ++int32_t DWC_WAITQ_WAIT(dwc_waitq_t *wq, dwc_waitq_condition_t cond, void *data) ++{ ++ int result = wait_event_interruptible(wq->queue, ++ cond(data) || wq->abort); ++ if (result == -ERESTARTSYS) { ++ wq->abort = 0; ++ return -DWC_E_RESTART; ++ } ++ ++ if (wq->abort == 1) { ++ wq->abort = 0; ++ return -DWC_E_ABORT; ++ } ++ ++ wq->abort = 0; ++ ++ if (result == 0) { ++ return 0; ++ } ++ ++ return -DWC_E_UNKNOWN; ++} ++ ++int32_t DWC_WAITQ_WAIT_TIMEOUT(dwc_waitq_t *wq, dwc_waitq_condition_t cond, ++ void *data, int32_t msecs) ++{ ++ int32_t tmsecs; ++ int result = wait_event_interruptible_timeout(wq->queue, ++ cond(data) || wq->abort, ++ msecs_to_jiffies(msecs)); ++ if (result == -ERESTARTSYS) { ++ wq->abort = 0; ++ return -DWC_E_RESTART; ++ } ++ ++ if (wq->abort == 1) { ++ wq->abort = 0; ++ return -DWC_E_ABORT; ++ } ++ ++ wq->abort = 0; ++ ++ if (result > 0) { ++ tmsecs = jiffies_to_msecs(result); ++ if (!tmsecs) { ++ return 1; ++ } ++ ++ return tmsecs; ++ } ++ ++ if (result == 0) { ++ return -DWC_E_TIMEOUT; ++ } ++ ++ return -DWC_E_UNKNOWN; ++} ++ ++void DWC_WAITQ_TRIGGER(dwc_waitq_t *wq) ++{ ++ wq->abort = 0; ++ wake_up_interruptible(&wq->queue); ++} ++ ++void DWC_WAITQ_ABORT(dwc_waitq_t *wq) ++{ ++ wq->abort = 1; ++ wake_up_interruptible(&wq->queue); ++} ++ ++ ++/* Threading */ ++ ++dwc_thread_t *DWC_THREAD_RUN(dwc_thread_function_t func, char *name, void *data) ++{ ++ struct task_struct *thread = kthread_run(func, data, name); ++ ++ if (thread == ERR_PTR(-ENOMEM)) { ++ return NULL; ++ } ++ ++ return (dwc_thread_t *)thread; ++} ++ ++int DWC_THREAD_STOP(dwc_thread_t *thread) ++{ ++ return kthread_stop((struct task_struct *)thread); ++} ++ ++dwc_bool_t DWC_THREAD_SHOULD_STOP(void) ++{ ++ return kthread_should_stop(); ++} ++ ++ ++/* tasklets ++ - run in interrupt context (cannot sleep) ++ - each tasklet runs on a single CPU ++ - different tasklets can be running simultaneously on different CPUs ++ */ ++struct dwc_tasklet { ++ struct tasklet_struct t; ++ dwc_tasklet_callback_t cb; ++ void *data; ++}; ++ ++static void tasklet_callback(unsigned long data) ++{ ++ dwc_tasklet_t *t = (dwc_tasklet_t *)data; ++ t->cb(t->data); ++} ++ ++dwc_tasklet_t *DWC_TASK_ALLOC(char *name, dwc_tasklet_callback_t cb, void *data) ++{ ++ dwc_tasklet_t *t = DWC_ALLOC(sizeof(*t)); ++ ++ if (t) { ++ t->cb = cb; ++ t->data = data; ++ tasklet_init(&t->t, tasklet_callback, (unsigned long)t); ++ } else { ++ DWC_ERROR("Cannot allocate memory for tasklet\n"); ++ } ++ ++ return t; ++} ++ ++void DWC_TASK_FREE(dwc_tasklet_t *task) ++{ ++ DWC_FREE(task); ++} ++ ++void DWC_TASK_SCHEDULE(dwc_tasklet_t *task) ++{ ++ tasklet_schedule(&task->t); ++} ++ ++void DWC_TASK_HI_SCHEDULE(dwc_tasklet_t *task) ++{ ++ tasklet_hi_schedule(&task->t); ++} ++ ++ ++/* workqueues ++ - run in process context (can sleep) ++ */ ++typedef struct work_container { ++ dwc_work_callback_t cb; ++ void *data; ++ dwc_workq_t *wq; ++ char *name; ++ ++#ifdef DEBUG ++ DWC_CIRCLEQ_ENTRY(work_container) entry; ++#endif ++ struct delayed_work work; ++} work_container_t; ++ ++#ifdef DEBUG ++DWC_CIRCLEQ_HEAD(work_container_queue, work_container); ++#endif ++ ++struct dwc_workq { ++ struct workqueue_struct *wq; ++ dwc_spinlock_t *lock; ++ dwc_waitq_t *waitq; ++ int pending; ++ ++#ifdef DEBUG ++ struct work_container_queue entries; ++#endif ++}; ++ ++static void do_work(struct work_struct *work) ++{ ++ dwc_irqflags_t flags; ++ struct delayed_work *dw = container_of(work, struct delayed_work, work); ++ work_container_t *container = container_of(dw, struct work_container, work); ++ dwc_workq_t *wq = container->wq; ++ ++ container->cb(container->data); ++ ++#ifdef DEBUG ++ DWC_CIRCLEQ_REMOVE(&wq->entries, container, entry); ++#endif ++ DWC_DEBUGC("Work done: %s, container=%p", container->name, container); ++ if (container->name) { ++ DWC_FREE(container->name); ++ } ++ DWC_FREE(container); ++ ++ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags); ++ wq->pending--; ++ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags); ++ DWC_WAITQ_TRIGGER(wq->waitq); ++} ++ ++static int work_done(void *data) ++{ ++ dwc_workq_t *workq = (dwc_workq_t *)data; ++ return workq->pending == 0; ++} ++ ++int DWC_WORKQ_WAIT_WORK_DONE(dwc_workq_t *workq, int timeout) ++{ ++ return DWC_WAITQ_WAIT_TIMEOUT(workq->waitq, work_done, workq, timeout); ++} ++ ++dwc_workq_t *DWC_WORKQ_ALLOC(char *name) ++{ ++ dwc_workq_t *wq = DWC_ALLOC(sizeof(*wq)); ++ ++ if (!wq) { ++ return NULL; ++ } ++ ++ wq->wq = create_singlethread_workqueue(name); ++ if (!wq->wq) { ++ goto no_wq; ++ } ++ ++ wq->pending = 0; ++ ++#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_SPINLOCK)) ++ DWC_SPINLOCK_ALLOC_LINUX_DEBUG(wq->lock); ++#else ++ wq->lock = DWC_SPINLOCK_ALLOC(); ++#endif ++ if (!wq->lock) { ++ goto no_lock; ++ } ++ ++ wq->waitq = DWC_WAITQ_ALLOC(); ++ if (!wq->waitq) { ++ goto no_waitq; ++ } ++ ++#ifdef DEBUG ++ DWC_CIRCLEQ_INIT(&wq->entries); ++#endif ++ return wq; ++ ++ no_waitq: ++ DWC_SPINLOCK_FREE(wq->lock); ++ no_lock: ++ destroy_workqueue(wq->wq); ++ no_wq: ++ DWC_FREE(wq); ++ ++ return NULL; ++} ++ ++void DWC_WORKQ_FREE(dwc_workq_t *wq) ++{ ++#ifdef DEBUG ++ if (wq->pending != 0) { ++ struct work_container *wc; ++ DWC_ERROR("Destroying work queue with pending work"); ++ DWC_CIRCLEQ_FOREACH(wc, &wq->entries, entry) { ++ DWC_ERROR("Work %s still pending", wc->name); ++ } ++ } ++#endif ++ destroy_workqueue(wq->wq); ++ DWC_SPINLOCK_FREE(wq->lock); ++ DWC_WAITQ_FREE(wq->waitq); ++ DWC_FREE(wq); ++} ++ ++void DWC_WORKQ_SCHEDULE(dwc_workq_t *wq, dwc_work_callback_t cb, void *data, ++ char *format, ...) ++{ ++ dwc_irqflags_t flags; ++ work_container_t *container; ++ static char name[128]; ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VSNPRINTF(name, 128, format, args); ++ va_end(args); ++ ++ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags); ++ wq->pending++; ++ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags); ++ DWC_WAITQ_TRIGGER(wq->waitq); ++ ++ container = DWC_ALLOC_ATOMIC(sizeof(*container)); ++ if (!container) { ++ DWC_ERROR("Cannot allocate memory for container\n"); ++ return; ++ } ++ ++ container->name = DWC_STRDUP(name); ++ if (!container->name) { ++ DWC_ERROR("Cannot allocate memory for container->name\n"); ++ DWC_FREE(container); ++ return; ++ } ++ ++ container->cb = cb; ++ container->data = data; ++ container->wq = wq; ++ DWC_DEBUGC("Queueing work: %s, container=%p", container->name, container); ++ INIT_WORK(&container->work.work, do_work); ++ ++#ifdef DEBUG ++ DWC_CIRCLEQ_INSERT_TAIL(&wq->entries, container, entry); ++#endif ++ queue_work(wq->wq, &container->work.work); ++} ++ ++void DWC_WORKQ_SCHEDULE_DELAYED(dwc_workq_t *wq, dwc_work_callback_t cb, ++ void *data, uint32_t time, char *format, ...) ++{ ++ dwc_irqflags_t flags; ++ work_container_t *container; ++ static char name[128]; ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VSNPRINTF(name, 128, format, args); ++ va_end(args); ++ ++ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags); ++ wq->pending++; ++ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags); ++ DWC_WAITQ_TRIGGER(wq->waitq); ++ ++ container = DWC_ALLOC_ATOMIC(sizeof(*container)); ++ if (!container) { ++ DWC_ERROR("Cannot allocate memory for container\n"); ++ return; ++ } ++ ++ container->name = DWC_STRDUP(name); ++ if (!container->name) { ++ DWC_ERROR("Cannot allocate memory for container->name\n"); ++ DWC_FREE(container); ++ return; ++ } ++ ++ container->cb = cb; ++ container->data = data; ++ container->wq = wq; ++ DWC_DEBUGC("Queueing work: %s, container=%p", container->name, container); ++ INIT_DELAYED_WORK(&container->work, do_work); ++ ++#ifdef DEBUG ++ DWC_CIRCLEQ_INSERT_TAIL(&wq->entries, container, entry); ++#endif ++ queue_delayed_work(wq->wq, &container->work, msecs_to_jiffies(time)); ++} ++ ++int DWC_WORKQ_PENDING(dwc_workq_t *wq) ++{ ++ return wq->pending; ++} ++ ++ ++#ifdef DWC_LIBMODULE ++ ++#ifdef DWC_CCLIB ++/* CC */ ++EXPORT_SYMBOL(dwc_cc_if_alloc); ++EXPORT_SYMBOL(dwc_cc_if_free); ++EXPORT_SYMBOL(dwc_cc_clear); ++EXPORT_SYMBOL(dwc_cc_add); ++EXPORT_SYMBOL(dwc_cc_remove); ++EXPORT_SYMBOL(dwc_cc_change); ++EXPORT_SYMBOL(dwc_cc_data_for_save); ++EXPORT_SYMBOL(dwc_cc_restore_from_data); ++EXPORT_SYMBOL(dwc_cc_match_chid); ++EXPORT_SYMBOL(dwc_cc_match_cdid); ++EXPORT_SYMBOL(dwc_cc_ck); ++EXPORT_SYMBOL(dwc_cc_chid); ++EXPORT_SYMBOL(dwc_cc_cdid); ++EXPORT_SYMBOL(dwc_cc_name); ++#endif /* DWC_CCLIB */ ++ ++#ifdef DWC_CRYPTOLIB ++# ifndef CONFIG_MACH_IPMATE ++/* Modpow */ ++EXPORT_SYMBOL(dwc_modpow); ++ ++/* DH */ ++EXPORT_SYMBOL(dwc_dh_modpow); ++EXPORT_SYMBOL(dwc_dh_derive_keys); ++EXPORT_SYMBOL(dwc_dh_pk); ++# endif /* CONFIG_MACH_IPMATE */ ++ ++/* Crypto */ ++EXPORT_SYMBOL(dwc_wusb_aes_encrypt); ++EXPORT_SYMBOL(dwc_wusb_cmf); ++EXPORT_SYMBOL(dwc_wusb_prf); ++EXPORT_SYMBOL(dwc_wusb_fill_ccm_nonce); ++EXPORT_SYMBOL(dwc_wusb_gen_nonce); ++EXPORT_SYMBOL(dwc_wusb_gen_key); ++EXPORT_SYMBOL(dwc_wusb_gen_mic); ++#endif /* DWC_CRYPTOLIB */ ++ ++/* Notification */ ++#ifdef DWC_NOTIFYLIB ++EXPORT_SYMBOL(dwc_alloc_notification_manager); ++EXPORT_SYMBOL(dwc_free_notification_manager); ++EXPORT_SYMBOL(dwc_register_notifier); ++EXPORT_SYMBOL(dwc_unregister_notifier); ++EXPORT_SYMBOL(dwc_add_observer); ++EXPORT_SYMBOL(dwc_remove_observer); ++EXPORT_SYMBOL(dwc_notify); ++#endif ++ ++/* Memory Debugging Routines */ ++#ifdef DWC_DEBUG_MEMORY ++EXPORT_SYMBOL(dwc_alloc_debug); ++EXPORT_SYMBOL(dwc_alloc_atomic_debug); ++EXPORT_SYMBOL(dwc_free_debug); ++EXPORT_SYMBOL(dwc_dma_alloc_debug); ++EXPORT_SYMBOL(dwc_dma_free_debug); ++#endif ++ ++EXPORT_SYMBOL(DWC_MEMSET); ++EXPORT_SYMBOL(DWC_MEMCPY); ++EXPORT_SYMBOL(DWC_MEMMOVE); ++EXPORT_SYMBOL(DWC_MEMCMP); ++EXPORT_SYMBOL(DWC_STRNCMP); ++EXPORT_SYMBOL(DWC_STRCMP); ++EXPORT_SYMBOL(DWC_STRLEN); ++EXPORT_SYMBOL(DWC_STRCPY); ++EXPORT_SYMBOL(DWC_STRDUP); ++EXPORT_SYMBOL(DWC_ATOI); ++EXPORT_SYMBOL(DWC_ATOUI); ++ ++#ifdef DWC_UTFLIB ++EXPORT_SYMBOL(DWC_UTF8_TO_UTF16LE); ++#endif /* DWC_UTFLIB */ ++ ++EXPORT_SYMBOL(DWC_IN_IRQ); ++EXPORT_SYMBOL(DWC_IN_BH); ++EXPORT_SYMBOL(DWC_VPRINTF); ++EXPORT_SYMBOL(DWC_VSNPRINTF); ++EXPORT_SYMBOL(DWC_PRINTF); ++EXPORT_SYMBOL(DWC_SPRINTF); ++EXPORT_SYMBOL(DWC_SNPRINTF); ++EXPORT_SYMBOL(__DWC_WARN); ++EXPORT_SYMBOL(__DWC_ERROR); ++EXPORT_SYMBOL(DWC_EXCEPTION); ++ ++#ifdef DEBUG ++EXPORT_SYMBOL(__DWC_DEBUG); ++#endif ++ ++EXPORT_SYMBOL(__DWC_DMA_ALLOC); ++EXPORT_SYMBOL(__DWC_DMA_ALLOC_ATOMIC); ++EXPORT_SYMBOL(__DWC_DMA_FREE); ++EXPORT_SYMBOL(__DWC_ALLOC); ++EXPORT_SYMBOL(__DWC_ALLOC_ATOMIC); ++EXPORT_SYMBOL(__DWC_FREE); ++ ++#ifdef DWC_CRYPTOLIB ++EXPORT_SYMBOL(DWC_RANDOM_BYTES); ++EXPORT_SYMBOL(DWC_AES_CBC); ++EXPORT_SYMBOL(DWC_SHA256); ++EXPORT_SYMBOL(DWC_HMAC_SHA256); ++#endif ++ ++EXPORT_SYMBOL(DWC_CPU_TO_LE32); ++EXPORT_SYMBOL(DWC_CPU_TO_BE32); ++EXPORT_SYMBOL(DWC_LE32_TO_CPU); ++EXPORT_SYMBOL(DWC_BE32_TO_CPU); ++EXPORT_SYMBOL(DWC_CPU_TO_LE16); ++EXPORT_SYMBOL(DWC_CPU_TO_BE16); ++EXPORT_SYMBOL(DWC_LE16_TO_CPU); ++EXPORT_SYMBOL(DWC_BE16_TO_CPU); ++EXPORT_SYMBOL(DWC_READ_REG32); ++EXPORT_SYMBOL(DWC_WRITE_REG32); ++EXPORT_SYMBOL(DWC_MODIFY_REG32); ++ ++#if 0 ++EXPORT_SYMBOL(DWC_READ_REG64); ++EXPORT_SYMBOL(DWC_WRITE_REG64); ++EXPORT_SYMBOL(DWC_MODIFY_REG64); ++#endif ++ ++EXPORT_SYMBOL(DWC_SPINLOCK_ALLOC); ++EXPORT_SYMBOL(DWC_SPINLOCK_FREE); ++EXPORT_SYMBOL(DWC_SPINLOCK); ++EXPORT_SYMBOL(DWC_SPINUNLOCK); ++EXPORT_SYMBOL(DWC_SPINLOCK_IRQSAVE); ++EXPORT_SYMBOL(DWC_SPINUNLOCK_IRQRESTORE); ++EXPORT_SYMBOL(DWC_MUTEX_ALLOC); ++ ++#if (!defined(DWC_LINUX) || !defined(CONFIG_DEBUG_MUTEXES)) ++EXPORT_SYMBOL(DWC_MUTEX_FREE); ++#endif ++ ++EXPORT_SYMBOL(DWC_MUTEX_LOCK); ++EXPORT_SYMBOL(DWC_MUTEX_TRYLOCK); ++EXPORT_SYMBOL(DWC_MUTEX_UNLOCK); ++EXPORT_SYMBOL(DWC_UDELAY); ++EXPORT_SYMBOL(DWC_MDELAY); ++EXPORT_SYMBOL(DWC_MSLEEP); ++EXPORT_SYMBOL(DWC_TIME); ++EXPORT_SYMBOL(DWC_TIMER_ALLOC); ++EXPORT_SYMBOL(DWC_TIMER_FREE); ++EXPORT_SYMBOL(DWC_TIMER_SCHEDULE); ++EXPORT_SYMBOL(DWC_TIMER_CANCEL); ++EXPORT_SYMBOL(DWC_WAITQ_ALLOC); ++EXPORT_SYMBOL(DWC_WAITQ_FREE); ++EXPORT_SYMBOL(DWC_WAITQ_WAIT); ++EXPORT_SYMBOL(DWC_WAITQ_WAIT_TIMEOUT); ++EXPORT_SYMBOL(DWC_WAITQ_TRIGGER); ++EXPORT_SYMBOL(DWC_WAITQ_ABORT); ++EXPORT_SYMBOL(DWC_THREAD_RUN); ++EXPORT_SYMBOL(DWC_THREAD_STOP); ++EXPORT_SYMBOL(DWC_THREAD_SHOULD_STOP); ++EXPORT_SYMBOL(DWC_TASK_ALLOC); ++EXPORT_SYMBOL(DWC_TASK_FREE); ++EXPORT_SYMBOL(DWC_TASK_SCHEDULE); ++EXPORT_SYMBOL(DWC_WORKQ_WAIT_WORK_DONE); ++EXPORT_SYMBOL(DWC_WORKQ_ALLOC); ++EXPORT_SYMBOL(DWC_WORKQ_FREE); ++EXPORT_SYMBOL(DWC_WORKQ_SCHEDULE); ++EXPORT_SYMBOL(DWC_WORKQ_SCHEDULE_DELAYED); ++EXPORT_SYMBOL(DWC_WORKQ_PENDING); ++ ++static int dwc_common_port_init_module(void) ++{ ++ int result = 0; ++ ++ printk(KERN_DEBUG "Module dwc_common_port init\n" ); ++ ++#ifdef DWC_DEBUG_MEMORY ++ result = dwc_memory_debug_start(NULL); ++ if (result) { ++ printk(KERN_ERR ++ "dwc_memory_debug_start() failed with error %d\n", ++ result); ++ return result; ++ } ++#endif ++ ++#ifdef DWC_NOTIFYLIB ++ result = dwc_alloc_notification_manager(NULL, NULL); ++ if (result) { ++ printk(KERN_ERR ++ "dwc_alloc_notification_manager() failed with error %d\n", ++ result); ++ return result; ++ } ++#endif ++ return result; ++} ++ ++static void dwc_common_port_exit_module(void) ++{ ++ printk(KERN_DEBUG "Module dwc_common_port exit\n" ); ++ ++#ifdef DWC_NOTIFYLIB ++ dwc_free_notification_manager(); ++#endif ++ ++#ifdef DWC_DEBUG_MEMORY ++ dwc_memory_debug_stop(); ++#endif ++} ++ ++module_init(dwc_common_port_init_module); ++module_exit(dwc_common_port_exit_module); ++ ++MODULE_DESCRIPTION("DWC Common Library - Portable version"); ++MODULE_AUTHOR("Synopsys Inc."); ++MODULE_LICENSE ("GPL"); ++ ++#endif /* DWC_LIBMODULE */ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_common_nbsd.c +@@ -0,0 +1,1275 @@ ++#include "dwc_os.h" ++#include "dwc_list.h" ++ ++#ifdef DWC_CCLIB ++# include "dwc_cc.h" ++#endif ++ ++#ifdef DWC_CRYPTOLIB ++# include "dwc_modpow.h" ++# include "dwc_dh.h" ++# include "dwc_crypto.h" ++#endif ++ ++#ifdef DWC_NOTIFYLIB ++# include "dwc_notifier.h" ++#endif ++ ++/* OS-Level Implementations */ ++ ++/* This is the NetBSD 4.0.1 kernel implementation of the DWC platform library. */ ++ ++ ++/* MISC */ ++ ++void *DWC_MEMSET(void *dest, uint8_t byte, uint32_t size) ++{ ++ return memset(dest, byte, size); ++} ++ ++void *DWC_MEMCPY(void *dest, void const *src, uint32_t size) ++{ ++ return memcpy(dest, src, size); ++} ++ ++void *DWC_MEMMOVE(void *dest, void *src, uint32_t size) ++{ ++ bcopy(src, dest, size); ++ return dest; ++} ++ ++int DWC_MEMCMP(void *m1, void *m2, uint32_t size) ++{ ++ return memcmp(m1, m2, size); ++} ++ ++int DWC_STRNCMP(void *s1, void *s2, uint32_t size) ++{ ++ return strncmp(s1, s2, size); ++} ++ ++int DWC_STRCMP(void *s1, void *s2) ++{ ++ return strcmp(s1, s2); ++} ++ ++int DWC_STRLEN(char const *str) ++{ ++ return strlen(str); ++} ++ ++char *DWC_STRCPY(char *to, char const *from) ++{ ++ return strcpy(to, from); ++} ++ ++char *DWC_STRDUP(char const *str) ++{ ++ int len = DWC_STRLEN(str) + 1; ++ char *new = DWC_ALLOC_ATOMIC(len); ++ ++ if (!new) { ++ return NULL; ++ } ++ ++ DWC_MEMCPY(new, str, len); ++ return new; ++} ++ ++int DWC_ATOI(char *str, int32_t *value) ++{ ++ char *end = NULL; ++ ++ /* NetBSD doesn't have 'strtol' in the kernel, but 'strtoul' ++ * should be equivalent on 2's complement machines ++ */ ++ *value = strtoul(str, &end, 0); ++ if (*end == '\0') { ++ return 0; ++ } ++ ++ return -1; ++} ++ ++int DWC_ATOUI(char *str, uint32_t *value) ++{ ++ char *end = NULL; ++ ++ *value = strtoul(str, &end, 0); ++ if (*end == '\0') { ++ return 0; ++ } ++ ++ return -1; ++} ++ ++ ++#ifdef DWC_UTFLIB ++/* From usbstring.c */ ++ ++int DWC_UTF8_TO_UTF16LE(uint8_t const *s, uint16_t *cp, unsigned len) ++{ ++ int count = 0; ++ u8 c; ++ u16 uchar; ++ ++ /* this insists on correct encodings, though not minimal ones. ++ * BUT it currently rejects legit 4-byte UTF-8 code points, ++ * which need surrogate pairs. (Unicode 3.1 can use them.) ++ */ ++ while (len != 0 && (c = (u8) *s++) != 0) { ++ if (unlikely(c & 0x80)) { ++ // 2-byte sequence: ++ // 00000yyyyyxxxxxx = 110yyyyy 10xxxxxx ++ if ((c & 0xe0) == 0xc0) { ++ uchar = (c & 0x1f) << 6; ++ ++ c = (u8) *s++; ++ if ((c & 0xc0) != 0xc0) ++ goto fail; ++ c &= 0x3f; ++ uchar |= c; ++ ++ // 3-byte sequence (most CJKV characters): ++ // zzzzyyyyyyxxxxxx = 1110zzzz 10yyyyyy 10xxxxxx ++ } else if ((c & 0xf0) == 0xe0) { ++ uchar = (c & 0x0f) << 12; ++ ++ c = (u8) *s++; ++ if ((c & 0xc0) != 0xc0) ++ goto fail; ++ c &= 0x3f; ++ uchar |= c << 6; ++ ++ c = (u8) *s++; ++ if ((c & 0xc0) != 0xc0) ++ goto fail; ++ c &= 0x3f; ++ uchar |= c; ++ ++ /* no bogus surrogates */ ++ if (0xd800 <= uchar && uchar <= 0xdfff) ++ goto fail; ++ ++ // 4-byte sequence (surrogate pairs, currently rare): ++ // 11101110wwwwzzzzyy + 110111yyyyxxxxxx ++ // = 11110uuu 10uuzzzz 10yyyyyy 10xxxxxx ++ // (uuuuu = wwww + 1) ++ // FIXME accept the surrogate code points (only) ++ } else ++ goto fail; ++ } else ++ uchar = c; ++ put_unaligned (cpu_to_le16 (uchar), cp++); ++ count++; ++ len--; ++ } ++ return count; ++fail: ++ return -1; ++} ++ ++#endif /* DWC_UTFLIB */ ++ ++ ++/* dwc_debug.h */ ++ ++dwc_bool_t DWC_IN_IRQ(void) ++{ ++// return in_irq(); ++ return 0; ++} ++ ++dwc_bool_t DWC_IN_BH(void) ++{ ++// return in_softirq(); ++ return 0; ++} ++ ++void DWC_VPRINTF(char *format, va_list args) ++{ ++ vprintf(format, args); ++} ++ ++int DWC_VSNPRINTF(char *str, int size, char *format, va_list args) ++{ ++ return vsnprintf(str, size, format, args); ++} ++ ++void DWC_PRINTF(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++} ++ ++int DWC_SPRINTF(char *buffer, char *format, ...) ++{ ++ int retval; ++ va_list args; ++ ++ va_start(args, format); ++ retval = vsprintf(buffer, format, args); ++ va_end(args); ++ return retval; ++} ++ ++int DWC_SNPRINTF(char *buffer, int size, char *format, ...) ++{ ++ int retval; ++ va_list args; ++ ++ va_start(args, format); ++ retval = vsnprintf(buffer, size, format, args); ++ va_end(args); ++ return retval; ++} ++ ++void __DWC_WARN(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++} ++ ++void __DWC_ERROR(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++} ++ ++void DWC_EXCEPTION(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++// BUG_ON(1); ??? ++} ++ ++#ifdef DEBUG ++void __DWC_DEBUG(char *format, ...) ++{ ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VPRINTF(format, args); ++ va_end(args); ++} ++#endif ++ ++ ++/* dwc_mem.h */ ++ ++#if 0 ++dwc_pool_t *DWC_DMA_POOL_CREATE(uint32_t size, ++ uint32_t align, ++ uint32_t alloc) ++{ ++ struct dma_pool *pool = dma_pool_create("Pool", NULL, ++ size, align, alloc); ++ return (dwc_pool_t *)pool; ++} ++ ++void DWC_DMA_POOL_DESTROY(dwc_pool_t *pool) ++{ ++ dma_pool_destroy((struct dma_pool *)pool); ++} ++ ++void *DWC_DMA_POOL_ALLOC(dwc_pool_t *pool, uint64_t *dma_addr) ++{ ++// return dma_pool_alloc((struct dma_pool *)pool, GFP_KERNEL, dma_addr); ++ return dma_pool_alloc((struct dma_pool *)pool, M_WAITOK, dma_addr); ++} ++ ++void *DWC_DMA_POOL_ZALLOC(dwc_pool_t *pool, uint64_t *dma_addr) ++{ ++ void *vaddr = DWC_DMA_POOL_ALLOC(pool, dma_addr); ++ memset(..); ++} ++ ++void DWC_DMA_POOL_FREE(dwc_pool_t *pool, void *vaddr, void *daddr) ++{ ++ dma_pool_free(pool, vaddr, daddr); ++} ++#endif ++ ++void *__DWC_DMA_ALLOC(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr) ++{ ++ dwc_dmactx_t *dma = (dwc_dmactx_t *)dma_ctx; ++ int error; ++ ++ error = bus_dmamem_alloc(dma->dma_tag, size, 1, size, dma->segs, ++ sizeof(dma->segs) / sizeof(dma->segs[0]), ++ &dma->nsegs, BUS_DMA_NOWAIT); ++ if (error) { ++ printf("%s: bus_dmamem_alloc(%ju) failed: %d\n", __func__, ++ (uintmax_t)size, error); ++ goto fail_0; ++ } ++ ++ error = bus_dmamem_map(dma->dma_tag, dma->segs, dma->nsegs, size, ++ (caddr_t *)&dma->dma_vaddr, ++ BUS_DMA_NOWAIT | BUS_DMA_COHERENT); ++ if (error) { ++ printf("%s: bus_dmamem_map failed: %d\n", __func__, error); ++ goto fail_1; ++ } ++ ++ error = bus_dmamap_create(dma->dma_tag, size, 1, size, 0, ++ BUS_DMA_NOWAIT, &dma->dma_map); ++ if (error) { ++ printf("%s: bus_dmamap_create failed: %d\n", __func__, error); ++ goto fail_2; ++ } ++ ++ error = bus_dmamap_load(dma->dma_tag, dma->dma_map, dma->dma_vaddr, ++ size, NULL, BUS_DMA_NOWAIT); ++ if (error) { ++ printf("%s: bus_dmamap_load failed: %d\n", __func__, error); ++ goto fail_3; ++ } ++ ++ dma->dma_paddr = (bus_addr_t)dma->segs[0].ds_addr; ++ *dma_addr = dma->dma_paddr; ++ return dma->dma_vaddr; ++ ++fail_3: ++ bus_dmamap_destroy(dma->dma_tag, dma->dma_map); ++fail_2: ++ bus_dmamem_unmap(dma->dma_tag, dma->dma_vaddr, size); ++fail_1: ++ bus_dmamem_free(dma->dma_tag, dma->segs, dma->nsegs); ++fail_0: ++ dma->dma_map = NULL; ++ dma->dma_vaddr = NULL; ++ dma->nsegs = 0; ++ ++ return NULL; ++} ++ ++void __DWC_DMA_FREE(void *dma_ctx, uint32_t size, void *virt_addr, dwc_dma_t dma_addr) ++{ ++ dwc_dmactx_t *dma = (dwc_dmactx_t *)dma_ctx; ++ ++ if (dma->dma_map != NULL) { ++ bus_dmamap_sync(dma->dma_tag, dma->dma_map, 0, size, ++ BUS_DMASYNC_POSTREAD | BUS_DMASYNC_POSTWRITE); ++ bus_dmamap_unload(dma->dma_tag, dma->dma_map); ++ bus_dmamap_destroy(dma->dma_tag, dma->dma_map); ++ bus_dmamem_unmap(dma->dma_tag, dma->dma_vaddr, size); ++ bus_dmamem_free(dma->dma_tag, dma->segs, dma->nsegs); ++ dma->dma_paddr = 0; ++ dma->dma_map = NULL; ++ dma->dma_vaddr = NULL; ++ dma->nsegs = 0; ++ } ++} ++ ++void *__DWC_ALLOC(void *mem_ctx, uint32_t size) ++{ ++ return malloc(size, M_DEVBUF, M_WAITOK | M_ZERO); ++} ++ ++void *__DWC_ALLOC_ATOMIC(void *mem_ctx, uint32_t size) ++{ ++ return malloc(size, M_DEVBUF, M_NOWAIT | M_ZERO); ++} ++ ++void __DWC_FREE(void *mem_ctx, void *addr) ++{ ++ free(addr, M_DEVBUF); ++} ++ ++ ++#ifdef DWC_CRYPTOLIB ++/* dwc_crypto.h */ ++ ++void DWC_RANDOM_BYTES(uint8_t *buffer, uint32_t length) ++{ ++ get_random_bytes(buffer, length); ++} ++ ++int DWC_AES_CBC(uint8_t *message, uint32_t messagelen, uint8_t *key, uint32_t keylen, uint8_t iv[16], uint8_t *out) ++{ ++ struct crypto_blkcipher *tfm; ++ struct blkcipher_desc desc; ++ struct scatterlist sgd; ++ struct scatterlist sgs; ++ ++ tfm = crypto_alloc_blkcipher("cbc(aes)", 0, CRYPTO_ALG_ASYNC); ++ if (tfm == NULL) { ++ printk("failed to load transform for aes CBC\n"); ++ return -1; ++ } ++ ++ crypto_blkcipher_setkey(tfm, key, keylen); ++ crypto_blkcipher_set_iv(tfm, iv, 16); ++ ++ sg_init_one(&sgd, out, messagelen); ++ sg_init_one(&sgs, message, messagelen); ++ ++ desc.tfm = tfm; ++ desc.flags = 0; ++ ++ if (crypto_blkcipher_encrypt(&desc, &sgd, &sgs, messagelen)) { ++ crypto_free_blkcipher(tfm); ++ DWC_ERROR("AES CBC encryption failed"); ++ return -1; ++ } ++ ++ crypto_free_blkcipher(tfm); ++ return 0; ++} ++ ++int DWC_SHA256(uint8_t *message, uint32_t len, uint8_t *out) ++{ ++ struct crypto_hash *tfm; ++ struct hash_desc desc; ++ struct scatterlist sg; ++ ++ tfm = crypto_alloc_hash("sha256", 0, CRYPTO_ALG_ASYNC); ++ if (IS_ERR(tfm)) { ++ DWC_ERROR("Failed to load transform for sha256: %ld", PTR_ERR(tfm)); ++ return 0; ++ } ++ desc.tfm = tfm; ++ desc.flags = 0; ++ ++ sg_init_one(&sg, message, len); ++ crypto_hash_digest(&desc, &sg, len, out); ++ crypto_free_hash(tfm); ++ ++ return 1; ++} ++ ++int DWC_HMAC_SHA256(uint8_t *message, uint32_t messagelen, ++ uint8_t *key, uint32_t keylen, uint8_t *out) ++{ ++ struct crypto_hash *tfm; ++ struct hash_desc desc; ++ struct scatterlist sg; ++ ++ tfm = crypto_alloc_hash("hmac(sha256)", 0, CRYPTO_ALG_ASYNC); ++ if (IS_ERR(tfm)) { ++ DWC_ERROR("Failed to load transform for hmac(sha256): %ld", PTR_ERR(tfm)); ++ return 0; ++ } ++ desc.tfm = tfm; ++ desc.flags = 0; ++ ++ sg_init_one(&sg, message, messagelen); ++ crypto_hash_setkey(tfm, key, keylen); ++ crypto_hash_digest(&desc, &sg, messagelen, out); ++ crypto_free_hash(tfm); ++ ++ return 1; ++} ++ ++#endif /* DWC_CRYPTOLIB */ ++ ++ ++/* Byte Ordering Conversions */ ++ ++uint32_t DWC_CPU_TO_LE32(uint32_t *p) ++{ ++#ifdef __LITTLE_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ ++ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24)); ++#endif ++} ++ ++uint32_t DWC_CPU_TO_BE32(uint32_t *p) ++{ ++#ifdef __BIG_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ ++ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24)); ++#endif ++} ++ ++uint32_t DWC_LE32_TO_CPU(uint32_t *p) ++{ ++#ifdef __LITTLE_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ ++ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24)); ++#endif ++} ++ ++uint32_t DWC_BE32_TO_CPU(uint32_t *p) ++{ ++#ifdef __BIG_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ ++ return (u_p[3] | (u_p[2] << 8) | (u_p[1] << 16) | (u_p[0] << 24)); ++#endif ++} ++ ++uint16_t DWC_CPU_TO_LE16(uint16_t *p) ++{ ++#ifdef __LITTLE_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ return (u_p[1] | (u_p[0] << 8)); ++#endif ++} ++ ++uint16_t DWC_CPU_TO_BE16(uint16_t *p) ++{ ++#ifdef __BIG_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ return (u_p[1] | (u_p[0] << 8)); ++#endif ++} ++ ++uint16_t DWC_LE16_TO_CPU(uint16_t *p) ++{ ++#ifdef __LITTLE_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ return (u_p[1] | (u_p[0] << 8)); ++#endif ++} ++ ++uint16_t DWC_BE16_TO_CPU(uint16_t *p) ++{ ++#ifdef __BIG_ENDIAN ++ return *p; ++#else ++ uint8_t *u_p = (uint8_t *)p; ++ return (u_p[1] | (u_p[0] << 8)); ++#endif ++} ++ ++ ++/* Registers */ ++ ++uint32_t DWC_READ_REG32(void *io_ctx, uint32_t volatile *reg) ++{ ++ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx; ++ bus_size_t ior = (bus_size_t)reg; ++ ++ return bus_space_read_4(io->iot, io->ioh, ior); ++} ++ ++#if 0 ++uint64_t DWC_READ_REG64(void *io_ctx, uint64_t volatile *reg) ++{ ++ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx; ++ bus_size_t ior = (bus_size_t)reg; ++ ++ return bus_space_read_8(io->iot, io->ioh, ior); ++} ++#endif ++ ++void DWC_WRITE_REG32(void *io_ctx, uint32_t volatile *reg, uint32_t value) ++{ ++ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx; ++ bus_size_t ior = (bus_size_t)reg; ++ ++ bus_space_write_4(io->iot, io->ioh, ior, value); ++} ++ ++#if 0 ++void DWC_WRITE_REG64(void *io_ctx, uint64_t volatile *reg, uint64_t value) ++{ ++ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx; ++ bus_size_t ior = (bus_size_t)reg; ++ ++ bus_space_write_8(io->iot, io->ioh, ior, value); ++} ++#endif ++ ++void DWC_MODIFY_REG32(void *io_ctx, uint32_t volatile *reg, uint32_t clear_mask, ++ uint32_t set_mask) ++{ ++ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx; ++ bus_size_t ior = (bus_size_t)reg; ++ ++ bus_space_write_4(io->iot, io->ioh, ior, ++ (bus_space_read_4(io->iot, io->ioh, ior) & ++ ~clear_mask) | set_mask); ++} ++ ++#if 0 ++void DWC_MODIFY_REG64(void *io_ctx, uint64_t volatile *reg, uint64_t clear_mask, ++ uint64_t set_mask) ++{ ++ dwc_ioctx_t *io = (dwc_ioctx_t *)io_ctx; ++ bus_size_t ior = (bus_size_t)reg; ++ ++ bus_space_write_8(io->iot, io->ioh, ior, ++ (bus_space_read_8(io->iot, io->ioh, ior) & ++ ~clear_mask) | set_mask); ++} ++#endif ++ ++ ++/* Locking */ ++ ++dwc_spinlock_t *DWC_SPINLOCK_ALLOC(void) ++{ ++ struct simplelock *sl = DWC_ALLOC(sizeof(*sl)); ++ ++ if (!sl) { ++ DWC_ERROR("Cannot allocate memory for spinlock"); ++ return NULL; ++ } ++ ++ simple_lock_init(sl); ++ return (dwc_spinlock_t *)sl; ++} ++ ++void DWC_SPINLOCK_FREE(dwc_spinlock_t *lock) ++{ ++ struct simplelock *sl = (struct simplelock *)lock; ++ ++ DWC_FREE(sl); ++} ++ ++void DWC_SPINLOCK(dwc_spinlock_t *lock) ++{ ++ simple_lock((struct simplelock *)lock); ++} ++ ++void DWC_SPINUNLOCK(dwc_spinlock_t *lock) ++{ ++ simple_unlock((struct simplelock *)lock); ++} ++ ++void DWC_SPINLOCK_IRQSAVE(dwc_spinlock_t *lock, dwc_irqflags_t *flags) ++{ ++ simple_lock((struct simplelock *)lock); ++ *flags = splbio(); ++} ++ ++void DWC_SPINUNLOCK_IRQRESTORE(dwc_spinlock_t *lock, dwc_irqflags_t flags) ++{ ++ splx(flags); ++ simple_unlock((struct simplelock *)lock); ++} ++ ++dwc_mutex_t *DWC_MUTEX_ALLOC(void) ++{ ++ dwc_mutex_t *mutex = DWC_ALLOC(sizeof(struct lock)); ++ ++ if (!mutex) { ++ DWC_ERROR("Cannot allocate memory for mutex"); ++ return NULL; ++ } ++ ++ lockinit((struct lock *)mutex, 0, "dw3mtx", 0, 0); ++ return mutex; ++} ++ ++#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES)) ++#else ++void DWC_MUTEX_FREE(dwc_mutex_t *mutex) ++{ ++ DWC_FREE(mutex); ++} ++#endif ++ ++void DWC_MUTEX_LOCK(dwc_mutex_t *mutex) ++{ ++ lockmgr((struct lock *)mutex, LK_EXCLUSIVE, NULL); ++} ++ ++int DWC_MUTEX_TRYLOCK(dwc_mutex_t *mutex) ++{ ++ int status; ++ ++ status = lockmgr((struct lock *)mutex, LK_EXCLUSIVE | LK_NOWAIT, NULL); ++ return status == 0; ++} ++ ++void DWC_MUTEX_UNLOCK(dwc_mutex_t *mutex) ++{ ++ lockmgr((struct lock *)mutex, LK_RELEASE, NULL); ++} ++ ++ ++/* Timing */ ++ ++void DWC_UDELAY(uint32_t usecs) ++{ ++ DELAY(usecs); ++} ++ ++void DWC_MDELAY(uint32_t msecs) ++{ ++ do { ++ DELAY(1000); ++ } while (--msecs); ++} ++ ++void DWC_MSLEEP(uint32_t msecs) ++{ ++ struct timeval tv; ++ ++ tv.tv_sec = msecs / 1000; ++ tv.tv_usec = (msecs - tv.tv_sec * 1000) * 1000; ++ tsleep(&tv, 0, "dw3slp", tvtohz(&tv)); ++} ++ ++uint32_t DWC_TIME(void) ++{ ++ struct timeval tv; ++ ++ microuptime(&tv); // or getmicrouptime? (less precise, but faster) ++ return tv.tv_sec * 1000 + tv.tv_usec / 1000; ++} ++ ++ ++/* Timers */ ++ ++struct dwc_timer { ++ struct callout t; ++ char *name; ++ dwc_spinlock_t *lock; ++ dwc_timer_callback_t cb; ++ void *data; ++}; ++ ++dwc_timer_t *DWC_TIMER_ALLOC(char *name, dwc_timer_callback_t cb, void *data) ++{ ++ dwc_timer_t *t = DWC_ALLOC(sizeof(*t)); ++ ++ if (!t) { ++ DWC_ERROR("Cannot allocate memory for timer"); ++ return NULL; ++ } ++ ++ callout_init(&t->t); ++ ++ t->name = DWC_STRDUP(name); ++ if (!t->name) { ++ DWC_ERROR("Cannot allocate memory for timer->name"); ++ goto no_name; ++ } ++ ++ t->lock = DWC_SPINLOCK_ALLOC(); ++ if (!t->lock) { ++ DWC_ERROR("Cannot allocate memory for timer->lock"); ++ goto no_lock; ++ } ++ ++ t->cb = cb; ++ t->data = data; ++ ++ return t; ++ ++ no_lock: ++ DWC_FREE(t->name); ++ no_name: ++ DWC_FREE(t); ++ ++ return NULL; ++} ++ ++void DWC_TIMER_FREE(dwc_timer_t *timer) ++{ ++ callout_stop(&timer->t); ++ DWC_SPINLOCK_FREE(timer->lock); ++ DWC_FREE(timer->name); ++ DWC_FREE(timer); ++} ++ ++void DWC_TIMER_SCHEDULE(dwc_timer_t *timer, uint32_t time) ++{ ++ struct timeval tv; ++ ++ tv.tv_sec = time / 1000; ++ tv.tv_usec = (time - tv.tv_sec * 1000) * 1000; ++ callout_reset(&timer->t, tvtohz(&tv), timer->cb, timer->data); ++} ++ ++void DWC_TIMER_CANCEL(dwc_timer_t *timer) ++{ ++ callout_stop(&timer->t); ++} ++ ++ ++/* Wait Queues */ ++ ++struct dwc_waitq { ++ struct simplelock lock; ++ int abort; ++}; ++ ++dwc_waitq_t *DWC_WAITQ_ALLOC(void) ++{ ++ dwc_waitq_t *wq = DWC_ALLOC(sizeof(*wq)); ++ ++ if (!wq) { ++ DWC_ERROR("Cannot allocate memory for waitqueue"); ++ return NULL; ++ } ++ ++ simple_lock_init(&wq->lock); ++ wq->abort = 0; ++ ++ return wq; ++} ++ ++void DWC_WAITQ_FREE(dwc_waitq_t *wq) ++{ ++ DWC_FREE(wq); ++} ++ ++int32_t DWC_WAITQ_WAIT(dwc_waitq_t *wq, dwc_waitq_condition_t cond, void *data) ++{ ++ int ipl; ++ int result = 0; ++ ++ simple_lock(&wq->lock); ++ ipl = splbio(); ++ ++ /* Skip the sleep if already aborted or triggered */ ++ if (!wq->abort && !cond(data)) { ++ splx(ipl); ++ result = ltsleep(wq, PCATCH, "dw3wat", 0, &wq->lock); // infinite timeout ++ ipl = splbio(); ++ } ++ ++ if (result == 0) { // awoken ++ if (wq->abort) { ++ wq->abort = 0; ++ result = -DWC_E_ABORT; ++ } else { ++ result = 0; ++ } ++ ++ splx(ipl); ++ simple_unlock(&wq->lock); ++ } else { ++ wq->abort = 0; ++ splx(ipl); ++ simple_unlock(&wq->lock); ++ ++ if (result == ERESTART) { // signaled - restart ++ result = -DWC_E_RESTART; ++ } else { // signaled - must be EINTR ++ result = -DWC_E_ABORT; ++ } ++ } ++ ++ return result; ++} ++ ++int32_t DWC_WAITQ_WAIT_TIMEOUT(dwc_waitq_t *wq, dwc_waitq_condition_t cond, ++ void *data, int32_t msecs) ++{ ++ struct timeval tv, tv1, tv2; ++ int ipl; ++ int result = 0; ++ ++ tv.tv_sec = msecs / 1000; ++ tv.tv_usec = (msecs - tv.tv_sec * 1000) * 1000; ++ ++ simple_lock(&wq->lock); ++ ipl = splbio(); ++ ++ /* Skip the sleep if already aborted or triggered */ ++ if (!wq->abort && !cond(data)) { ++ splx(ipl); ++ getmicrouptime(&tv1); ++ result = ltsleep(wq, PCATCH, "dw3wto", tvtohz(&tv), &wq->lock); ++ getmicrouptime(&tv2); ++ ipl = splbio(); ++ } ++ ++ if (result == 0) { // awoken ++ if (wq->abort) { ++ wq->abort = 0; ++ splx(ipl); ++ simple_unlock(&wq->lock); ++ result = -DWC_E_ABORT; ++ } else { ++ splx(ipl); ++ simple_unlock(&wq->lock); ++ ++ tv2.tv_usec -= tv1.tv_usec; ++ if (tv2.tv_usec < 0) { ++ tv2.tv_usec += 1000000; ++ tv2.tv_sec--; ++ } ++ ++ tv2.tv_sec -= tv1.tv_sec; ++ result = tv2.tv_sec * 1000 + tv2.tv_usec / 1000; ++ result = msecs - result; ++ if (result <= 0) ++ result = 1; ++ } ++ } else { ++ wq->abort = 0; ++ splx(ipl); ++ simple_unlock(&wq->lock); ++ ++ if (result == ERESTART) { // signaled - restart ++ result = -DWC_E_RESTART; ++ ++ } else if (result == EINTR) { // signaled - interrupt ++ result = -DWC_E_ABORT; ++ ++ } else { // timed out ++ result = -DWC_E_TIMEOUT; ++ } ++ } ++ ++ return result; ++} ++ ++void DWC_WAITQ_TRIGGER(dwc_waitq_t *wq) ++{ ++ wakeup(wq); ++} ++ ++void DWC_WAITQ_ABORT(dwc_waitq_t *wq) ++{ ++ int ipl; ++ ++ simple_lock(&wq->lock); ++ ipl = splbio(); ++ wq->abort = 1; ++ wakeup(wq); ++ splx(ipl); ++ simple_unlock(&wq->lock); ++} ++ ++ ++/* Threading */ ++ ++struct dwc_thread { ++ struct proc *proc; ++ int abort; ++}; ++ ++dwc_thread_t *DWC_THREAD_RUN(dwc_thread_function_t func, char *name, void *data) ++{ ++ int retval; ++ dwc_thread_t *thread = DWC_ALLOC(sizeof(*thread)); ++ ++ if (!thread) { ++ return NULL; ++ } ++ ++ thread->abort = 0; ++ retval = kthread_create1((void (*)(void *))func, data, &thread->proc, ++ "%s", name); ++ if (retval) { ++ DWC_FREE(thread); ++ return NULL; ++ } ++ ++ return thread; ++} ++ ++int DWC_THREAD_STOP(dwc_thread_t *thread) ++{ ++ int retval; ++ ++ thread->abort = 1; ++ retval = tsleep(&thread->abort, 0, "dw3stp", 60 * hz); ++ ++ if (retval == 0) { ++ /* DWC_THREAD_EXIT() will free the thread struct */ ++ return 0; ++ } ++ ++ /* NOTE: We leak the thread struct if thread doesn't die */ ++ ++ if (retval == EWOULDBLOCK) { ++ return -DWC_E_TIMEOUT; ++ } ++ ++ return -DWC_E_UNKNOWN; ++} ++ ++dwc_bool_t DWC_THREAD_SHOULD_STOP(dwc_thread_t *thread) ++{ ++ return thread->abort; ++} ++ ++void DWC_THREAD_EXIT(dwc_thread_t *thread) ++{ ++ wakeup(&thread->abort); ++ DWC_FREE(thread); ++ kthread_exit(0); ++} ++ ++/* tasklets ++ - Runs in interrupt context (cannot sleep) ++ - Each tasklet runs on a single CPU ++ - Different tasklets can be running simultaneously on different CPUs ++ [ On NetBSD there is no corresponding mechanism, drivers don't have bottom- ++ halves. So we just call the callback directly from DWC_TASK_SCHEDULE() ] ++ */ ++struct dwc_tasklet { ++ dwc_tasklet_callback_t cb; ++ void *data; ++}; ++ ++static void tasklet_callback(void *data) ++{ ++ dwc_tasklet_t *task = (dwc_tasklet_t *)data; ++ ++ task->cb(task->data); ++} ++ ++dwc_tasklet_t *DWC_TASK_ALLOC(char *name, dwc_tasklet_callback_t cb, void *data) ++{ ++ dwc_tasklet_t *task = DWC_ALLOC(sizeof(*task)); ++ ++ if (task) { ++ task->cb = cb; ++ task->data = data; ++ } else { ++ DWC_ERROR("Cannot allocate memory for tasklet"); ++ } ++ ++ return task; ++} ++ ++void DWC_TASK_FREE(dwc_tasklet_t *task) ++{ ++ DWC_FREE(task); ++} ++ ++void DWC_TASK_SCHEDULE(dwc_tasklet_t *task) ++{ ++ tasklet_callback(task); ++} ++ ++ ++/* workqueues ++ - Runs in process context (can sleep) ++ */ ++typedef struct work_container { ++ dwc_work_callback_t cb; ++ void *data; ++ dwc_workq_t *wq; ++ char *name; ++ int hz; ++ struct work task; ++} work_container_t; ++ ++struct dwc_workq { ++ struct workqueue *taskq; ++ dwc_spinlock_t *lock; ++ dwc_waitq_t *waitq; ++ int pending; ++ struct work_container *container; ++}; ++ ++static void do_work(struct work *task, void *data) ++{ ++ dwc_workq_t *wq = (dwc_workq_t *)data; ++ work_container_t *container = wq->container; ++ dwc_irqflags_t flags; ++ ++ if (container->hz) { ++ tsleep(container, 0, "dw3wrk", container->hz); ++ } ++ ++ container->cb(container->data); ++ DWC_DEBUG("Work done: %s, container=%p", container->name, container); ++ ++ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags); ++ if (container->name) ++ DWC_FREE(container->name); ++ DWC_FREE(container); ++ wq->pending--; ++ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags); ++ DWC_WAITQ_TRIGGER(wq->waitq); ++} ++ ++static int work_done(void *data) ++{ ++ dwc_workq_t *workq = (dwc_workq_t *)data; ++ ++ return workq->pending == 0; ++} ++ ++int DWC_WORKQ_WAIT_WORK_DONE(dwc_workq_t *workq, int timeout) ++{ ++ return DWC_WAITQ_WAIT_TIMEOUT(workq->waitq, work_done, workq, timeout); ++} ++ ++dwc_workq_t *DWC_WORKQ_ALLOC(char *name) ++{ ++ int result; ++ dwc_workq_t *wq = DWC_ALLOC(sizeof(*wq)); ++ ++ if (!wq) { ++ DWC_ERROR("Cannot allocate memory for workqueue"); ++ return NULL; ++ } ++ ++ result = workqueue_create(&wq->taskq, name, do_work, wq, 0 /*PWAIT*/, ++ IPL_BIO, 0); ++ if (result) { ++ DWC_ERROR("Cannot create workqueue"); ++ goto no_taskq; ++ } ++ ++ wq->pending = 0; ++ ++ wq->lock = DWC_SPINLOCK_ALLOC(); ++ if (!wq->lock) { ++ DWC_ERROR("Cannot allocate memory for spinlock"); ++ goto no_lock; ++ } ++ ++ wq->waitq = DWC_WAITQ_ALLOC(); ++ if (!wq->waitq) { ++ DWC_ERROR("Cannot allocate memory for waitqueue"); ++ goto no_waitq; ++ } ++ ++ return wq; ++ ++ no_waitq: ++ DWC_SPINLOCK_FREE(wq->lock); ++ no_lock: ++ workqueue_destroy(wq->taskq); ++ no_taskq: ++ DWC_FREE(wq); ++ ++ return NULL; ++} ++ ++void DWC_WORKQ_FREE(dwc_workq_t *wq) ++{ ++#ifdef DEBUG ++ dwc_irqflags_t flags; ++ ++ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags); ++ ++ if (wq->pending != 0) { ++ struct work_container *container = wq->container; ++ ++ DWC_ERROR("Destroying work queue with pending work"); ++ ++ if (container && container->name) { ++ DWC_ERROR("Work %s still pending", container->name); ++ } ++ } ++ ++ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags); ++#endif ++ DWC_WAITQ_FREE(wq->waitq); ++ DWC_SPINLOCK_FREE(wq->lock); ++ workqueue_destroy(wq->taskq); ++ DWC_FREE(wq); ++} ++ ++void DWC_WORKQ_SCHEDULE(dwc_workq_t *wq, dwc_work_callback_t cb, void *data, ++ char *format, ...) ++{ ++ dwc_irqflags_t flags; ++ work_container_t *container; ++ static char name[128]; ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VSNPRINTF(name, 128, format, args); ++ va_end(args); ++ ++ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags); ++ wq->pending++; ++ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags); ++ DWC_WAITQ_TRIGGER(wq->waitq); ++ ++ container = DWC_ALLOC_ATOMIC(sizeof(*container)); ++ if (!container) { ++ DWC_ERROR("Cannot allocate memory for container"); ++ return; ++ } ++ ++ container->name = DWC_STRDUP(name); ++ if (!container->name) { ++ DWC_ERROR("Cannot allocate memory for container->name"); ++ DWC_FREE(container); ++ return; ++ } ++ ++ container->cb = cb; ++ container->data = data; ++ container->wq = wq; ++ container->hz = 0; ++ wq->container = container; ++ ++ DWC_DEBUG("Queueing work: %s, container=%p", container->name, container); ++ workqueue_enqueue(wq->taskq, &container->task); ++} ++ ++void DWC_WORKQ_SCHEDULE_DELAYED(dwc_workq_t *wq, dwc_work_callback_t cb, ++ void *data, uint32_t time, char *format, ...) ++{ ++ dwc_irqflags_t flags; ++ work_container_t *container; ++ static char name[128]; ++ struct timeval tv; ++ va_list args; ++ ++ va_start(args, format); ++ DWC_VSNPRINTF(name, 128, format, args); ++ va_end(args); ++ ++ DWC_SPINLOCK_IRQSAVE(wq->lock, &flags); ++ wq->pending++; ++ DWC_SPINUNLOCK_IRQRESTORE(wq->lock, flags); ++ DWC_WAITQ_TRIGGER(wq->waitq); ++ ++ container = DWC_ALLOC_ATOMIC(sizeof(*container)); ++ if (!container) { ++ DWC_ERROR("Cannot allocate memory for container"); ++ return; ++ } ++ ++ container->name = DWC_STRDUP(name); ++ if (!container->name) { ++ DWC_ERROR("Cannot allocate memory for container->name"); ++ DWC_FREE(container); ++ return; ++ } ++ ++ container->cb = cb; ++ container->data = data; ++ container->wq = wq; ++ tv.tv_sec = time / 1000; ++ tv.tv_usec = (time - tv.tv_sec * 1000) * 1000; ++ container->hz = tvtohz(&tv); ++ wq->container = container; ++ ++ DWC_DEBUG("Queueing work: %s, container=%p", container->name, container); ++ workqueue_enqueue(wq->taskq, &container->task); ++} ++ ++int DWC_WORKQ_PENDING(dwc_workq_t *wq) ++{ ++ return wq->pending; ++} +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_crypto.c +@@ -0,0 +1,308 @@ ++/* ========================================================================= ++ * $File: //dwh/usb_iip/dev/software/dwc_common_port_2/dwc_crypto.c $ ++ * $Revision: #5 $ ++ * $Date: 2010/09/28 $ ++ * $Change: 1596182 $ ++ * ++ * Synopsys Portability Library Software and documentation ++ * (hereinafter, "Software") is an Unsupported proprietary work of ++ * Synopsys, Inc. unless otherwise expressly agreed to in writing ++ * between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product ++ * under any End User Software License Agreement or Agreement for ++ * Licensed Product with Synopsys or any supplement thereto. You are ++ * permitted to use and redistribute this Software in source and binary ++ * forms, with or without modification, provided that redistributions ++ * of source code must retain this notice. You may not view, use, ++ * disclose, copy or distribute this file or any information contained ++ * herein except pursuant to this license grant from Synopsys. If you ++ * do not agree with this notice, including the disclaimer below, then ++ * you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" ++ * BASIS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT ++ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS ++ * FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. IN NO EVENT SHALL ++ * SYNOPSYS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY ++ * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE ++ * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================= */ ++ ++/** @file ++ * This file contains the WUSB cryptographic routines. ++ */ ++ ++#ifdef DWC_CRYPTOLIB ++ ++#include "dwc_crypto.h" ++#include "usb.h" ++ ++#ifdef DEBUG ++static inline void dump_bytes(char *name, uint8_t *bytes, int len) ++{ ++ int i; ++ DWC_PRINTF("%s: ", name); ++ for (i=0; idst == src, then the bytes will be encrypted ++ * in-place. ++ * ++ * @return 0 on success, negative error code on error. ++ */ ++int dwc_wusb_aes_encrypt(u8 *src, u8 *key, u8 *dst) ++{ ++ u8 block_t[16]; ++ DWC_MEMSET(block_t, 0, 16); ++ ++ return DWC_AES_CBC(src, 16, key, 16, block_t, dst); ++} ++ ++/** ++ * The CCM-MAC-FUNCTION described in section 6.5 of the WUSB spec. ++ * This function takes a data string and returns the encrypted CBC ++ * Counter-mode MIC. ++ * ++ * @param key The 128-bit symmetric key. ++ * @param nonce The CCM nonce. ++ * @param label The unique 14-byte ASCII text label. ++ * @param bytes The byte array to be encrypted. ++ * @param len Length of the byte array. ++ * @param result Byte array to receive the 8-byte encrypted MIC. ++ */ ++void dwc_wusb_cmf(u8 *key, u8 *nonce, ++ char *label, u8 *bytes, int len, u8 *result) ++{ ++ u8 block_m[16]; ++ u8 block_x[16]; ++ u8 block_t[8]; ++ int idx, blkNum; ++ u16 la = (u16)(len + 14); ++ ++ /* Set the AES-128 key */ ++ //dwc_aes_setkey(tfm, key, 16); ++ ++ /* Fill block B0 from flags = 0x59, N, and l(m) = 0 */ ++ block_m[0] = 0x59; ++ for (idx = 0; idx < 13; idx++) ++ block_m[idx + 1] = nonce[idx]; ++ block_m[14] = 0; ++ block_m[15] = 0; ++ ++ /* Produce the CBC IV */ ++ dwc_wusb_aes_encrypt(block_m, key, block_x); ++ show_block(block_m, "CBC IV in: ", "\n", 0); ++ show_block(block_x, "CBC IV out:", "\n", 0); ++ ++ /* Fill block B1 from l(a) = Blen + 14, and A */ ++ block_x[0] ^= (u8)(la >> 8); ++ block_x[1] ^= (u8)la; ++ for (idx = 0; idx < 14; idx++) ++ block_x[idx + 2] ^= label[idx]; ++ show_block(block_x, "After xor: ", "b1\n", 16); ++ ++ dwc_wusb_aes_encrypt(block_x, key, block_x); ++ show_block(block_x, "After AES: ", "b1\n", 16); ++ ++ idx = 0; ++ blkNum = 0; ++ ++ /* Fill remaining blocks with B */ ++ while (len-- > 0) { ++ block_x[idx] ^= *bytes++; ++ if (++idx >= 16) { ++ idx = 0; ++ show_block(block_x, "After xor: ", "\n", blkNum); ++ dwc_wusb_aes_encrypt(block_x, key, block_x); ++ show_block(block_x, "After AES: ", "\n", blkNum); ++ blkNum++; ++ } ++ } ++ ++ /* Handle partial last block */ ++ if (idx > 0) { ++ show_block(block_x, "After xor: ", "\n", blkNum); ++ dwc_wusb_aes_encrypt(block_x, key, block_x); ++ show_block(block_x, "After AES: ", "\n", blkNum); ++ } ++ ++ /* Save the MIC tag */ ++ DWC_MEMCPY(block_t, block_x, 8); ++ show_block(block_t, "MIC tag : ", NULL, 8); ++ ++ /* Fill block A0 from flags = 0x01, N, and counter = 0 */ ++ block_m[0] = 0x01; ++ block_m[14] = 0; ++ block_m[15] = 0; ++ ++ /* Encrypt the counter */ ++ dwc_wusb_aes_encrypt(block_m, key, block_x); ++ show_block(block_x, "CTR[MIC] : ", NULL, 8); ++ ++ /* XOR with MIC tag */ ++ for (idx = 0; idx < 8; idx++) { ++ block_t[idx] ^= block_x[idx]; ++ } ++ ++ /* Return result to caller */ ++ DWC_MEMCPY(result, block_t, 8); ++ show_block(result, "CCM-MIC : ", NULL, 8); ++ ++} ++ ++/** ++ * The PRF function described in section 6.5 of the WUSB spec. This function ++ * concatenates MIC values returned from dwc_cmf() to create a value of ++ * the requested length. ++ * ++ * @param prf_len Length of the PRF function in bits (64, 128, or 256). ++ * @param key, nonce, label, bytes, len Same as for dwc_cmf(). ++ * @param result Byte array to receive the result. ++ */ ++void dwc_wusb_prf(int prf_len, u8 *key, ++ u8 *nonce, char *label, u8 *bytes, int len, u8 *result) ++{ ++ int i; ++ ++ nonce[0] = 0; ++ for (i = 0; i < prf_len >> 6; i++, nonce[0]++) { ++ dwc_wusb_cmf(key, nonce, label, bytes, len, result); ++ result += 8; ++ } ++} ++ ++/** ++ * Fills in CCM Nonce per the WUSB spec. ++ * ++ * @param[in] haddr Host address. ++ * @param[in] daddr Device address. ++ * @param[in] tkid Session Key(PTK) identifier. ++ * @param[out] nonce Pointer to where the CCM Nonce output is to be written. ++ */ ++void dwc_wusb_fill_ccm_nonce(uint16_t haddr, uint16_t daddr, uint8_t *tkid, ++ uint8_t *nonce) ++{ ++ ++ DWC_DEBUG("%s %x %x\n", __func__, daddr, haddr); ++ ++ DWC_MEMSET(&nonce[0], 0, 16); ++ ++ DWC_MEMCPY(&nonce[6], tkid, 3); ++ nonce[9] = daddr & 0xFF; ++ nonce[10] = (daddr >> 8) & 0xFF; ++ nonce[11] = haddr & 0xFF; ++ nonce[12] = (haddr >> 8) & 0xFF; ++ ++ dump_bytes("CCM nonce", nonce, 16); ++} ++ ++/** ++ * Generates a 16-byte cryptographic-grade random number for the Host/Device ++ * Nonce. ++ */ ++void dwc_wusb_gen_nonce(uint16_t addr, uint8_t *nonce) ++{ ++ uint8_t inonce[16]; ++ uint32_t temp[4]; ++ ++ /* Fill in the Nonce */ ++ DWC_MEMSET(&inonce[0], 0, sizeof(inonce)); ++ inonce[9] = addr & 0xFF; ++ inonce[10] = (addr >> 8) & 0xFF; ++ inonce[11] = inonce[9]; ++ inonce[12] = inonce[10]; ++ ++ /* Collect "randomness samples" */ ++ DWC_RANDOM_BYTES((uint8_t *)temp, 16); ++ ++ dwc_wusb_prf_128((uint8_t *)temp, nonce, ++ "Random Numbers", (uint8_t *)temp, sizeof(temp), ++ nonce); ++} ++ ++/** ++ * Generates the Session Key (PTK) and Key Confirmation Key (KCK) per the ++ * WUSB spec. ++ * ++ * @param[in] ccm_nonce Pointer to CCM Nonce. ++ * @param[in] mk Master Key to derive the session from ++ * @param[in] hnonce Pointer to Host Nonce. ++ * @param[in] dnonce Pointer to Device Nonce. ++ * @param[out] kck Pointer to where the KCK output is to be written. ++ * @param[out] ptk Pointer to where the PTK output is to be written. ++ */ ++void dwc_wusb_gen_key(uint8_t *ccm_nonce, uint8_t *mk, uint8_t *hnonce, ++ uint8_t *dnonce, uint8_t *kck, uint8_t *ptk) ++{ ++ uint8_t idata[32]; ++ uint8_t odata[32]; ++ ++ dump_bytes("ck", mk, 16); ++ dump_bytes("hnonce", hnonce, 16); ++ dump_bytes("dnonce", dnonce, 16); ++ ++ /* The data is the HNonce and DNonce concatenated */ ++ DWC_MEMCPY(&idata[0], hnonce, 16); ++ DWC_MEMCPY(&idata[16], dnonce, 16); ++ ++ dwc_wusb_prf_256(mk, ccm_nonce, "Pair-wise keys", idata, 32, odata); ++ ++ /* Low 16 bytes of the result is the KCK, high 16 is the PTK */ ++ DWC_MEMCPY(kck, &odata[0], 16); ++ DWC_MEMCPY(ptk, &odata[16], 16); ++ ++ dump_bytes("kck", kck, 16); ++ dump_bytes("ptk", ptk, 16); ++} ++ ++/** ++ * Generates the Message Integrity Code over the Handshake data per the ++ * WUSB spec. ++ * ++ * @param ccm_nonce Pointer to CCM Nonce. ++ * @param kck Pointer to Key Confirmation Key. ++ * @param data Pointer to Handshake data to be checked. ++ * @param mic Pointer to where the MIC output is to be written. ++ */ ++void dwc_wusb_gen_mic(uint8_t *ccm_nonce, uint8_t *kck, ++ uint8_t *data, uint8_t *mic) ++{ ++ ++ dwc_wusb_prf_64(kck, ccm_nonce, "out-of-bandMIC", ++ data, WUSB_HANDSHAKE_LEN_FOR_MIC, mic); ++} ++ ++#endif /* DWC_CRYPTOLIB */ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_crypto.h +@@ -0,0 +1,111 @@ ++/* ========================================================================= ++ * $File: //dwh/usb_iip/dev/software/dwc_common_port_2/dwc_crypto.h $ ++ * $Revision: #3 $ ++ * $Date: 2010/09/28 $ ++ * $Change: 1596182 $ ++ * ++ * Synopsys Portability Library Software and documentation ++ * (hereinafter, "Software") is an Unsupported proprietary work of ++ * Synopsys, Inc. unless otherwise expressly agreed to in writing ++ * between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product ++ * under any End User Software License Agreement or Agreement for ++ * Licensed Product with Synopsys or any supplement thereto. You are ++ * permitted to use and redistribute this Software in source and binary ++ * forms, with or without modification, provided that redistributions ++ * of source code must retain this notice. You may not view, use, ++ * disclose, copy or distribute this file or any information contained ++ * herein except pursuant to this license grant from Synopsys. If you ++ * do not agree with this notice, including the disclaimer below, then ++ * you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" ++ * BASIS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT ++ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS ++ * FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. IN NO EVENT SHALL ++ * SYNOPSYS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY ++ * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE ++ * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================= */ ++ ++#ifndef _DWC_CRYPTO_H_ ++#define _DWC_CRYPTO_H_ ++ ++#ifdef __cplusplus ++extern "C" { ++#endif ++ ++/** @file ++ * ++ * This file contains declarations for the WUSB Cryptographic routines as ++ * defined in the WUSB spec. They are only to be used internally by the DWC UWB ++ * modules. ++ */ ++ ++#include "dwc_os.h" ++ ++int dwc_wusb_aes_encrypt(u8 *src, u8 *key, u8 *dst); ++ ++void dwc_wusb_cmf(u8 *key, u8 *nonce, ++ char *label, u8 *bytes, int len, u8 *result); ++void dwc_wusb_prf(int prf_len, u8 *key, ++ u8 *nonce, char *label, u8 *bytes, int len, u8 *result); ++ ++/** ++ * The PRF-64 function described in section 6.5 of the WUSB spec. ++ * ++ * @param key, nonce, label, bytes, len, result Same as for dwc_prf(). ++ */ ++static inline void dwc_wusb_prf_64(u8 *key, u8 *nonce, ++ char *label, u8 *bytes, int len, u8 *result) ++{ ++ dwc_wusb_prf(64, key, nonce, label, bytes, len, result); ++} ++ ++/** ++ * The PRF-128 function described in section 6.5 of the WUSB spec. ++ * ++ * @param key, nonce, label, bytes, len, result Same as for dwc_prf(). ++ */ ++static inline void dwc_wusb_prf_128(u8 *key, u8 *nonce, ++ char *label, u8 *bytes, int len, u8 *result) ++{ ++ dwc_wusb_prf(128, key, nonce, label, bytes, len, result); ++} ++ ++/** ++ * The PRF-256 function described in section 6.5 of the WUSB spec. ++ * ++ * @param key, nonce, label, bytes, len, result Same as for dwc_prf(). ++ */ ++static inline void dwc_wusb_prf_256(u8 *key, u8 *nonce, ++ char *label, u8 *bytes, int len, u8 *result) ++{ ++ dwc_wusb_prf(256, key, nonce, label, bytes, len, result); ++} ++ ++ ++void dwc_wusb_fill_ccm_nonce(uint16_t haddr, uint16_t daddr, uint8_t *tkid, ++ uint8_t *nonce); ++void dwc_wusb_gen_nonce(uint16_t addr, ++ uint8_t *nonce); ++ ++void dwc_wusb_gen_key(uint8_t *ccm_nonce, uint8_t *mk, ++ uint8_t *hnonce, uint8_t *dnonce, ++ uint8_t *kck, uint8_t *ptk); ++ ++ ++void dwc_wusb_gen_mic(uint8_t *ccm_nonce, uint8_t ++ *kck, uint8_t *data, uint8_t *mic); ++ ++#ifdef __cplusplus ++} ++#endif ++ ++#endif /* _DWC_CRYPTO_H_ */ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_dh.c +@@ -0,0 +1,291 @@ ++/* ========================================================================= ++ * $File: //dwh/usb_iip/dev/software/dwc_common_port_2/dwc_dh.c $ ++ * $Revision: #3 $ ++ * $Date: 2010/09/28 $ ++ * $Change: 1596182 $ ++ * ++ * Synopsys Portability Library Software and documentation ++ * (hereinafter, "Software") is an Unsupported proprietary work of ++ * Synopsys, Inc. unless otherwise expressly agreed to in writing ++ * between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product ++ * under any End User Software License Agreement or Agreement for ++ * Licensed Product with Synopsys or any supplement thereto. You are ++ * permitted to use and redistribute this Software in source and binary ++ * forms, with or without modification, provided that redistributions ++ * of source code must retain this notice. You may not view, use, ++ * disclose, copy or distribute this file or any information contained ++ * herein except pursuant to this license grant from Synopsys. If you ++ * do not agree with this notice, including the disclaimer below, then ++ * you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" ++ * BASIS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT ++ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS ++ * FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. IN NO EVENT SHALL ++ * SYNOPSYS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY ++ * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE ++ * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================= */ ++#ifdef DWC_CRYPTOLIB ++ ++#ifndef CONFIG_MACH_IPMATE ++ ++#include "dwc_dh.h" ++#include "dwc_modpow.h" ++ ++#ifdef DEBUG ++/* This function prints out a buffer in the format described in the Association ++ * Model specification. */ ++static void dh_dump(char *str, void *_num, int len) ++{ ++ uint8_t *num = _num; ++ int i; ++ DWC_PRINTF("%s\n", str); ++ for (i = 0; i < len; i ++) { ++ DWC_PRINTF("%02x", num[i]); ++ if (((i + 1) % 2) == 0) DWC_PRINTF(" "); ++ if (((i + 1) % 26) == 0) DWC_PRINTF("\n"); ++ } ++ ++ DWC_PRINTF("\n"); ++} ++#else ++#define dh_dump(_x...) do {; } while(0) ++#endif ++ ++/* Constant g value */ ++static __u32 dh_g[] = { ++ 0x02000000, ++}; ++ ++/* Constant p value */ ++static __u32 dh_p[] = { ++ 0xFFFFFFFF, 0xFFFFFFFF, 0xA2DA0FC9, 0x34C26821, 0x8B62C6C4, 0xD11CDC80, 0x084E0229, 0x74CC678A, ++ 0xA6BE0B02, 0x229B133B, 0x79084A51, 0xDD04348E, 0xB31995EF, 0x1B433ACD, 0x6D0A2B30, 0x37145FF2, ++ 0x6D35E14F, 0x45C2516D, 0x76B585E4, 0xC67E5E62, 0xE9424CF4, 0x6BED37A6, 0xB65CFF0B, 0xEDB706F4, ++ 0xFB6B38EE, 0xA59F895A, 0x11249FAE, 0xE61F4B7C, 0x51662849, 0x3D5BE4EC, 0xB87C00C2, 0x05BF63A1, ++ 0x3648DA98, 0x9AD3551C, 0xA83F1669, 0x5FCF24FD, 0x235D6583, 0x96ADA3DC, 0x56F3621C, 0xBB528520, ++ 0x0729D59E, 0x6D969670, 0x4E350C67, 0x0498BC4A, 0x086C74F1, 0x7C2118CA, 0x465E9032, 0x3BCE362E, ++ 0x2C779EE3, 0x03860E18, 0xA283279B, 0x8FA207EC, 0xF05DC5B5, 0xC9524C6F, 0xF6CB2BDE, 0x18175895, ++ 0x7C499539, 0xE56A95EA, 0x1826D215, 0x1005FA98, 0x5A8E7215, 0x2DC4AA8A, 0x0D1733AD, 0x337A5004, ++ 0xAB2155A8, 0x64BA1CDF, 0x0485FBEC, 0x0AEFDB58, 0x5771EA8A, 0x7D0C065D, 0x850F97B3, 0xC7E4E1A6, ++ 0x8CAEF5AB, 0xD73309DB, 0xE0948C1E, 0x9D61254A, 0x26D2E3CE, 0x6BEED21A, 0x06FA2FF1, 0x64088AD9, ++ 0x730276D8, 0x646AC83E, 0x182B1F52, 0x0C207B17, 0x5717E1BB, 0x6C5D617A, 0xC0880977, 0xE246D9BA, ++ 0xA04FE208, 0x31ABE574, 0xFC5BDB43, 0x8E10FDE0, 0x20D1824B, 0xCAD23AA9, 0xFFFFFFFF, 0xFFFFFFFF, ++}; ++ ++static void dh_swap_bytes(void *_in, void *_out, uint32_t len) ++{ ++ uint8_t *in = _in; ++ uint8_t *out = _out; ++ int i; ++ for (i=0; inext = (link); \ ++ (link)->prev = (link); \ ++} while (0) ++ ++#define DWC_LIST_FIRST(link) ((link)->next) ++#define DWC_LIST_LAST(link) ((link)->prev) ++#define DWC_LIST_END(link) (link) ++#define DWC_LIST_NEXT(link) ((link)->next) ++#define DWC_LIST_PREV(link) ((link)->prev) ++#define DWC_LIST_EMPTY(link) \ ++ (DWC_LIST_FIRST(link) == DWC_LIST_END(link)) ++#define DWC_LIST_ENTRY(link, type, field) \ ++ (type *)((uint8_t *)(link) - (size_t)(&((type *)0)->field)) ++ ++#if 0 ++#define DWC_LIST_INSERT_HEAD(list, link) do { \ ++ (link)->next = (list)->next; \ ++ (link)->prev = (list); \ ++ (list)->next->prev = (link); \ ++ (list)->next = (link); \ ++} while (0) ++ ++#define DWC_LIST_INSERT_TAIL(list, link) do { \ ++ (link)->next = (list); \ ++ (link)->prev = (list)->prev; \ ++ (list)->prev->next = (link); \ ++ (list)->prev = (link); \ ++} while (0) ++#else ++#define DWC_LIST_INSERT_HEAD(list, link) do { \ ++ dwc_list_link_t *__next__ = (list)->next; \ ++ __next__->prev = (link); \ ++ (link)->next = __next__; \ ++ (link)->prev = (list); \ ++ (list)->next = (link); \ ++} while (0) ++ ++#define DWC_LIST_INSERT_TAIL(list, link) do { \ ++ dwc_list_link_t *__prev__ = (list)->prev; \ ++ (list)->prev = (link); \ ++ (link)->next = (list); \ ++ (link)->prev = __prev__; \ ++ __prev__->next = (link); \ ++} while (0) ++#endif ++ ++#if 0 ++static inline void __list_add(struct list_head *new, ++ struct list_head *prev, ++ struct list_head *next) ++{ ++ next->prev = new; ++ new->next = next; ++ new->prev = prev; ++ prev->next = new; ++} ++ ++static inline void list_add(struct list_head *new, struct list_head *head) ++{ ++ __list_add(new, head, head->next); ++} ++ ++static inline void list_add_tail(struct list_head *new, struct list_head *head) ++{ ++ __list_add(new, head->prev, head); ++} ++ ++static inline void __list_del(struct list_head * prev, struct list_head * next) ++{ ++ next->prev = prev; ++ prev->next = next; ++} ++ ++static inline void list_del(struct list_head *entry) ++{ ++ __list_del(entry->prev, entry->next); ++ entry->next = LIST_POISON1; ++ entry->prev = LIST_POISON2; ++} ++#endif ++ ++#define DWC_LIST_REMOVE(link) do { \ ++ (link)->next->prev = (link)->prev; \ ++ (link)->prev->next = (link)->next; \ ++} while (0) ++ ++#define DWC_LIST_REMOVE_INIT(link) do { \ ++ DWC_LIST_REMOVE(link); \ ++ DWC_LIST_INIT(link); \ ++} while (0) ++ ++#define DWC_LIST_MOVE_HEAD(list, link) do { \ ++ DWC_LIST_REMOVE(link); \ ++ DWC_LIST_INSERT_HEAD(list, link); \ ++} while (0) ++ ++#define DWC_LIST_MOVE_TAIL(list, link) do { \ ++ DWC_LIST_REMOVE(link); \ ++ DWC_LIST_INSERT_TAIL(list, link); \ ++} while (0) ++ ++#define DWC_LIST_FOREACH(var, list) \ ++ for((var) = DWC_LIST_FIRST(list); \ ++ (var) != DWC_LIST_END(list); \ ++ (var) = DWC_LIST_NEXT(var)) ++ ++#define DWC_LIST_FOREACH_SAFE(var, var2, list) \ ++ for((var) = DWC_LIST_FIRST(list), (var2) = DWC_LIST_NEXT(var); \ ++ (var) != DWC_LIST_END(list); \ ++ (var) = (var2), (var2) = DWC_LIST_NEXT(var2)) ++ ++#define DWC_LIST_FOREACH_REVERSE(var, list) \ ++ for((var) = DWC_LIST_LAST(list); \ ++ (var) != DWC_LIST_END(list); \ ++ (var) = DWC_LIST_PREV(var)) ++ ++/* ++ * Singly-linked List definitions. ++ */ ++#define DWC_SLIST_HEAD(name, type) \ ++struct name { \ ++ struct type *slh_first; /* first element */ \ ++} ++ ++#define DWC_SLIST_HEAD_INITIALIZER(head) \ ++ { NULL } ++ ++#define DWC_SLIST_ENTRY(type) \ ++struct { \ ++ struct type *sle_next; /* next element */ \ ++} ++ ++/* ++ * Singly-linked List access methods. ++ */ ++#define DWC_SLIST_FIRST(head) ((head)->slh_first) ++#define DWC_SLIST_END(head) NULL ++#define DWC_SLIST_EMPTY(head) (SLIST_FIRST(head) == SLIST_END(head)) ++#define DWC_SLIST_NEXT(elm, field) ((elm)->field.sle_next) ++ ++#define DWC_SLIST_FOREACH(var, head, field) \ ++ for((var) = SLIST_FIRST(head); \ ++ (var) != SLIST_END(head); \ ++ (var) = SLIST_NEXT(var, field)) ++ ++#define DWC_SLIST_FOREACH_PREVPTR(var, varp, head, field) \ ++ for((varp) = &SLIST_FIRST((head)); \ ++ ((var) = *(varp)) != SLIST_END(head); \ ++ (varp) = &SLIST_NEXT((var), field)) ++ ++/* ++ * Singly-linked List functions. ++ */ ++#define DWC_SLIST_INIT(head) { \ ++ SLIST_FIRST(head) = SLIST_END(head); \ ++} ++ ++#define DWC_SLIST_INSERT_AFTER(slistelm, elm, field) do { \ ++ (elm)->field.sle_next = (slistelm)->field.sle_next; \ ++ (slistelm)->field.sle_next = (elm); \ ++} while (0) ++ ++#define DWC_SLIST_INSERT_HEAD(head, elm, field) do { \ ++ (elm)->field.sle_next = (head)->slh_first; \ ++ (head)->slh_first = (elm); \ ++} while (0) ++ ++#define DWC_SLIST_REMOVE_NEXT(head, elm, field) do { \ ++ (elm)->field.sle_next = (elm)->field.sle_next->field.sle_next; \ ++} while (0) ++ ++#define DWC_SLIST_REMOVE_HEAD(head, field) do { \ ++ (head)->slh_first = (head)->slh_first->field.sle_next; \ ++} while (0) ++ ++#define DWC_SLIST_REMOVE(head, elm, type, field) do { \ ++ if ((head)->slh_first == (elm)) { \ ++ SLIST_REMOVE_HEAD((head), field); \ ++ } \ ++ else { \ ++ struct type *curelm = (head)->slh_first; \ ++ while( curelm->field.sle_next != (elm) ) \ ++ curelm = curelm->field.sle_next; \ ++ curelm->field.sle_next = \ ++ curelm->field.sle_next->field.sle_next; \ ++ } \ ++} while (0) ++ ++/* ++ * Simple queue definitions. ++ */ ++#define DWC_SIMPLEQ_HEAD(name, type) \ ++struct name { \ ++ struct type *sqh_first; /* first element */ \ ++ struct type **sqh_last; /* addr of last next element */ \ ++} ++ ++#define DWC_SIMPLEQ_HEAD_INITIALIZER(head) \ ++ { NULL, &(head).sqh_first } ++ ++#define DWC_SIMPLEQ_ENTRY(type) \ ++struct { \ ++ struct type *sqe_next; /* next element */ \ ++} ++ ++/* ++ * Simple queue access methods. ++ */ ++#define DWC_SIMPLEQ_FIRST(head) ((head)->sqh_first) ++#define DWC_SIMPLEQ_END(head) NULL ++#define DWC_SIMPLEQ_EMPTY(head) (SIMPLEQ_FIRST(head) == SIMPLEQ_END(head)) ++#define DWC_SIMPLEQ_NEXT(elm, field) ((elm)->field.sqe_next) ++ ++#define DWC_SIMPLEQ_FOREACH(var, head, field) \ ++ for((var) = SIMPLEQ_FIRST(head); \ ++ (var) != SIMPLEQ_END(head); \ ++ (var) = SIMPLEQ_NEXT(var, field)) ++ ++/* ++ * Simple queue functions. ++ */ ++#define DWC_SIMPLEQ_INIT(head) do { \ ++ (head)->sqh_first = NULL; \ ++ (head)->sqh_last = &(head)->sqh_first; \ ++} while (0) ++ ++#define DWC_SIMPLEQ_INSERT_HEAD(head, elm, field) do { \ ++ if (((elm)->field.sqe_next = (head)->sqh_first) == NULL) \ ++ (head)->sqh_last = &(elm)->field.sqe_next; \ ++ (head)->sqh_first = (elm); \ ++} while (0) ++ ++#define DWC_SIMPLEQ_INSERT_TAIL(head, elm, field) do { \ ++ (elm)->field.sqe_next = NULL; \ ++ *(head)->sqh_last = (elm); \ ++ (head)->sqh_last = &(elm)->field.sqe_next; \ ++} while (0) ++ ++#define DWC_SIMPLEQ_INSERT_AFTER(head, listelm, elm, field) do { \ ++ if (((elm)->field.sqe_next = (listelm)->field.sqe_next) == NULL)\ ++ (head)->sqh_last = &(elm)->field.sqe_next; \ ++ (listelm)->field.sqe_next = (elm); \ ++} while (0) ++ ++#define DWC_SIMPLEQ_REMOVE_HEAD(head, field) do { \ ++ if (((head)->sqh_first = (head)->sqh_first->field.sqe_next) == NULL) \ ++ (head)->sqh_last = &(head)->sqh_first; \ ++} while (0) ++ ++/* ++ * Tail queue definitions. ++ */ ++#define DWC_TAILQ_HEAD(name, type) \ ++struct name { \ ++ struct type *tqh_first; /* first element */ \ ++ struct type **tqh_last; /* addr of last next element */ \ ++} ++ ++#define DWC_TAILQ_HEAD_INITIALIZER(head) \ ++ { NULL, &(head).tqh_first } ++ ++#define DWC_TAILQ_ENTRY(type) \ ++struct { \ ++ struct type *tqe_next; /* next element */ \ ++ struct type **tqe_prev; /* address of previous next element */ \ ++} ++ ++/* ++ * tail queue access methods ++ */ ++#define DWC_TAILQ_FIRST(head) ((head)->tqh_first) ++#define DWC_TAILQ_END(head) NULL ++#define DWC_TAILQ_NEXT(elm, field) ((elm)->field.tqe_next) ++#define DWC_TAILQ_LAST(head, headname) \ ++ (*(((struct headname *)((head)->tqh_last))->tqh_last)) ++/* XXX */ ++#define DWC_TAILQ_PREV(elm, headname, field) \ ++ (*(((struct headname *)((elm)->field.tqe_prev))->tqh_last)) ++#define DWC_TAILQ_EMPTY(head) \ ++ (DWC_TAILQ_FIRST(head) == DWC_TAILQ_END(head)) ++ ++#define DWC_TAILQ_FOREACH(var, head, field) \ ++ for ((var) = DWC_TAILQ_FIRST(head); \ ++ (var) != DWC_TAILQ_END(head); \ ++ (var) = DWC_TAILQ_NEXT(var, field)) ++ ++#define DWC_TAILQ_FOREACH_REVERSE(var, head, headname, field) \ ++ for ((var) = DWC_TAILQ_LAST(head, headname); \ ++ (var) != DWC_TAILQ_END(head); \ ++ (var) = DWC_TAILQ_PREV(var, headname, field)) ++ ++/* ++ * Tail queue functions. ++ */ ++#define DWC_TAILQ_INIT(head) do { \ ++ (head)->tqh_first = NULL; \ ++ (head)->tqh_last = &(head)->tqh_first; \ ++} while (0) ++ ++#define DWC_TAILQ_INSERT_HEAD(head, elm, field) do { \ ++ if (((elm)->field.tqe_next = (head)->tqh_first) != NULL) \ ++ (head)->tqh_first->field.tqe_prev = \ ++ &(elm)->field.tqe_next; \ ++ else \ ++ (head)->tqh_last = &(elm)->field.tqe_next; \ ++ (head)->tqh_first = (elm); \ ++ (elm)->field.tqe_prev = &(head)->tqh_first; \ ++} while (0) ++ ++#define DWC_TAILQ_INSERT_TAIL(head, elm, field) do { \ ++ (elm)->field.tqe_next = NULL; \ ++ (elm)->field.tqe_prev = (head)->tqh_last; \ ++ *(head)->tqh_last = (elm); \ ++ (head)->tqh_last = &(elm)->field.tqe_next; \ ++} while (0) ++ ++#define DWC_TAILQ_INSERT_AFTER(head, listelm, elm, field) do { \ ++ if (((elm)->field.tqe_next = (listelm)->field.tqe_next) != NULL)\ ++ (elm)->field.tqe_next->field.tqe_prev = \ ++ &(elm)->field.tqe_next; \ ++ else \ ++ (head)->tqh_last = &(elm)->field.tqe_next; \ ++ (listelm)->field.tqe_next = (elm); \ ++ (elm)->field.tqe_prev = &(listelm)->field.tqe_next; \ ++} while (0) ++ ++#define DWC_TAILQ_INSERT_BEFORE(listelm, elm, field) do { \ ++ (elm)->field.tqe_prev = (listelm)->field.tqe_prev; \ ++ (elm)->field.tqe_next = (listelm); \ ++ *(listelm)->field.tqe_prev = (elm); \ ++ (listelm)->field.tqe_prev = &(elm)->field.tqe_next; \ ++} while (0) ++ ++#define DWC_TAILQ_REMOVE(head, elm, field) do { \ ++ if (((elm)->field.tqe_next) != NULL) \ ++ (elm)->field.tqe_next->field.tqe_prev = \ ++ (elm)->field.tqe_prev; \ ++ else \ ++ (head)->tqh_last = (elm)->field.tqe_prev; \ ++ *(elm)->field.tqe_prev = (elm)->field.tqe_next; \ ++} while (0) ++ ++#define DWC_TAILQ_REPLACE(head, elm, elm2, field) do { \ ++ if (((elm2)->field.tqe_next = (elm)->field.tqe_next) != NULL) \ ++ (elm2)->field.tqe_next->field.tqe_prev = \ ++ &(elm2)->field.tqe_next; \ ++ else \ ++ (head)->tqh_last = &(elm2)->field.tqe_next; \ ++ (elm2)->field.tqe_prev = (elm)->field.tqe_prev; \ ++ *(elm2)->field.tqe_prev = (elm2); \ ++} while (0) ++ ++/* ++ * Circular queue definitions. ++ */ ++#define DWC_CIRCLEQ_HEAD(name, type) \ ++struct name { \ ++ struct type *cqh_first; /* first element */ \ ++ struct type *cqh_last; /* last element */ \ ++} ++ ++#define DWC_CIRCLEQ_HEAD_INITIALIZER(head) \ ++ { DWC_CIRCLEQ_END(&head), DWC_CIRCLEQ_END(&head) } ++ ++#define DWC_CIRCLEQ_ENTRY(type) \ ++struct { \ ++ struct type *cqe_next; /* next element */ \ ++ struct type *cqe_prev; /* previous element */ \ ++} ++ ++/* ++ * Circular queue access methods ++ */ ++#define DWC_CIRCLEQ_FIRST(head) ((head)->cqh_first) ++#define DWC_CIRCLEQ_LAST(head) ((head)->cqh_last) ++#define DWC_CIRCLEQ_END(head) ((void *)(head)) ++#define DWC_CIRCLEQ_NEXT(elm, field) ((elm)->field.cqe_next) ++#define DWC_CIRCLEQ_PREV(elm, field) ((elm)->field.cqe_prev) ++#define DWC_CIRCLEQ_EMPTY(head) \ ++ (DWC_CIRCLEQ_FIRST(head) == DWC_CIRCLEQ_END(head)) ++ ++#define DWC_CIRCLEQ_EMPTY_ENTRY(elm, field) (((elm)->field.cqe_next == NULL) && ((elm)->field.cqe_prev == NULL)) ++ ++#define DWC_CIRCLEQ_FOREACH(var, head, field) \ ++ for((var) = DWC_CIRCLEQ_FIRST(head); \ ++ (var) != DWC_CIRCLEQ_END(head); \ ++ (var) = DWC_CIRCLEQ_NEXT(var, field)) ++ ++#define DWC_CIRCLEQ_FOREACH_SAFE(var, var2, head, field) \ ++ for((var) = DWC_CIRCLEQ_FIRST(head), var2 = DWC_CIRCLEQ_NEXT(var, field); \ ++ (var) != DWC_CIRCLEQ_END(head); \ ++ (var) = var2, var2 = DWC_CIRCLEQ_NEXT(var, field)) ++ ++#define DWC_CIRCLEQ_FOREACH_REVERSE(var, head, field) \ ++ for((var) = DWC_CIRCLEQ_LAST(head); \ ++ (var) != DWC_CIRCLEQ_END(head); \ ++ (var) = DWC_CIRCLEQ_PREV(var, field)) ++ ++/* ++ * Circular queue functions. ++ */ ++#define DWC_CIRCLEQ_INIT(head) do { \ ++ (head)->cqh_first = DWC_CIRCLEQ_END(head); \ ++ (head)->cqh_last = DWC_CIRCLEQ_END(head); \ ++} while (0) ++ ++#define DWC_CIRCLEQ_INIT_ENTRY(elm, field) do { \ ++ (elm)->field.cqe_next = NULL; \ ++ (elm)->field.cqe_prev = NULL; \ ++} while (0) ++ ++#define DWC_CIRCLEQ_INSERT_AFTER(head, listelm, elm, field) do { \ ++ (elm)->field.cqe_next = (listelm)->field.cqe_next; \ ++ (elm)->field.cqe_prev = (listelm); \ ++ if ((listelm)->field.cqe_next == DWC_CIRCLEQ_END(head)) \ ++ (head)->cqh_last = (elm); \ ++ else \ ++ (listelm)->field.cqe_next->field.cqe_prev = (elm); \ ++ (listelm)->field.cqe_next = (elm); \ ++} while (0) ++ ++#define DWC_CIRCLEQ_INSERT_BEFORE(head, listelm, elm, field) do { \ ++ (elm)->field.cqe_next = (listelm); \ ++ (elm)->field.cqe_prev = (listelm)->field.cqe_prev; \ ++ if ((listelm)->field.cqe_prev == DWC_CIRCLEQ_END(head)) \ ++ (head)->cqh_first = (elm); \ ++ else \ ++ (listelm)->field.cqe_prev->field.cqe_next = (elm); \ ++ (listelm)->field.cqe_prev = (elm); \ ++} while (0) ++ ++#define DWC_CIRCLEQ_INSERT_HEAD(head, elm, field) do { \ ++ (elm)->field.cqe_next = (head)->cqh_first; \ ++ (elm)->field.cqe_prev = DWC_CIRCLEQ_END(head); \ ++ if ((head)->cqh_last == DWC_CIRCLEQ_END(head)) \ ++ (head)->cqh_last = (elm); \ ++ else \ ++ (head)->cqh_first->field.cqe_prev = (elm); \ ++ (head)->cqh_first = (elm); \ ++} while (0) ++ ++#define DWC_CIRCLEQ_INSERT_TAIL(head, elm, field) do { \ ++ (elm)->field.cqe_next = DWC_CIRCLEQ_END(head); \ ++ (elm)->field.cqe_prev = (head)->cqh_last; \ ++ if ((head)->cqh_first == DWC_CIRCLEQ_END(head)) \ ++ (head)->cqh_first = (elm); \ ++ else \ ++ (head)->cqh_last->field.cqe_next = (elm); \ ++ (head)->cqh_last = (elm); \ ++} while (0) ++ ++#define DWC_CIRCLEQ_REMOVE(head, elm, field) do { \ ++ if ((elm)->field.cqe_next == DWC_CIRCLEQ_END(head)) \ ++ (head)->cqh_last = (elm)->field.cqe_prev; \ ++ else \ ++ (elm)->field.cqe_next->field.cqe_prev = \ ++ (elm)->field.cqe_prev; \ ++ if ((elm)->field.cqe_prev == DWC_CIRCLEQ_END(head)) \ ++ (head)->cqh_first = (elm)->field.cqe_next; \ ++ else \ ++ (elm)->field.cqe_prev->field.cqe_next = \ ++ (elm)->field.cqe_next; \ ++} while (0) ++ ++#define DWC_CIRCLEQ_REMOVE_INIT(head, elm, field) do { \ ++ DWC_CIRCLEQ_REMOVE(head, elm, field); \ ++ DWC_CIRCLEQ_INIT_ENTRY(elm, field); \ ++} while (0) ++ ++#define DWC_CIRCLEQ_REPLACE(head, elm, elm2, field) do { \ ++ if (((elm2)->field.cqe_next = (elm)->field.cqe_next) == \ ++ DWC_CIRCLEQ_END(head)) \ ++ (head).cqh_last = (elm2); \ ++ else \ ++ (elm2)->field.cqe_next->field.cqe_prev = (elm2); \ ++ if (((elm2)->field.cqe_prev = (elm)->field.cqe_prev) == \ ++ DWC_CIRCLEQ_END(head)) \ ++ (head).cqh_first = (elm2); \ ++ else \ ++ (elm2)->field.cqe_prev->field.cqe_next = (elm2); \ ++} while (0) ++ ++#ifdef __cplusplus ++} ++#endif ++ ++#endif /* _DWC_LIST_H_ */ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_mem.c +@@ -0,0 +1,245 @@ ++/* Memory Debugging */ ++#ifdef DWC_DEBUG_MEMORY ++ ++#include "dwc_os.h" ++#include "dwc_list.h" ++ ++struct allocation { ++ void *addr; ++ void *ctx; ++ char *func; ++ int line; ++ uint32_t size; ++ int dma; ++ DWC_CIRCLEQ_ENTRY(allocation) entry; ++}; ++ ++DWC_CIRCLEQ_HEAD(allocation_queue, allocation); ++ ++struct allocation_manager { ++ void *mem_ctx; ++ struct allocation_queue allocations; ++ ++ /* statistics */ ++ int num; ++ int num_freed; ++ int num_active; ++ uint32_t total; ++ uint32_t cur; ++ uint32_t max; ++}; ++ ++static struct allocation_manager *manager = NULL; ++ ++static int add_allocation(void *ctx, uint32_t size, char const *func, int line, void *addr, ++ int dma) ++{ ++ struct allocation *a; ++ ++ DWC_ASSERT(manager != NULL, "manager not allocated"); ++ ++ a = __DWC_ALLOC_ATOMIC(manager->mem_ctx, sizeof(*a)); ++ if (!a) { ++ return -DWC_E_NO_MEMORY; ++ } ++ ++ a->func = __DWC_ALLOC_ATOMIC(manager->mem_ctx, DWC_STRLEN(func) + 1); ++ if (!a->func) { ++ __DWC_FREE(manager->mem_ctx, a); ++ return -DWC_E_NO_MEMORY; ++ } ++ ++ DWC_MEMCPY(a->func, func, DWC_STRLEN(func) + 1); ++ a->addr = addr; ++ a->ctx = ctx; ++ a->line = line; ++ a->size = size; ++ a->dma = dma; ++ DWC_CIRCLEQ_INSERT_TAIL(&manager->allocations, a, entry); ++ ++ /* Update stats */ ++ manager->num++; ++ manager->num_active++; ++ manager->total += size; ++ manager->cur += size; ++ ++ if (manager->max < manager->cur) { ++ manager->max = manager->cur; ++ } ++ ++ return 0; ++} ++ ++static struct allocation *find_allocation(void *ctx, void *addr) ++{ ++ struct allocation *a; ++ ++ DWC_CIRCLEQ_FOREACH(a, &manager->allocations, entry) { ++ if (a->ctx == ctx && a->addr == addr) { ++ return a; ++ } ++ } ++ ++ return NULL; ++} ++ ++static void free_allocation(void *ctx, void *addr, char const *func, int line) ++{ ++ struct allocation *a = find_allocation(ctx, addr); ++ ++ if (!a) { ++ DWC_ASSERT(0, ++ "Free of address %p that was never allocated or already freed %s:%d", ++ addr, func, line); ++ return; ++ } ++ ++ DWC_CIRCLEQ_REMOVE(&manager->allocations, a, entry); ++ ++ manager->num_active--; ++ manager->num_freed++; ++ manager->cur -= a->size; ++ __DWC_FREE(manager->mem_ctx, a->func); ++ __DWC_FREE(manager->mem_ctx, a); ++} ++ ++int dwc_memory_debug_start(void *mem_ctx) ++{ ++ DWC_ASSERT(manager == NULL, "Memory debugging has already started\n"); ++ ++ if (manager) { ++ return -DWC_E_BUSY; ++ } ++ ++ manager = __DWC_ALLOC(mem_ctx, sizeof(*manager)); ++ if (!manager) { ++ return -DWC_E_NO_MEMORY; ++ } ++ ++ DWC_CIRCLEQ_INIT(&manager->allocations); ++ manager->mem_ctx = mem_ctx; ++ manager->num = 0; ++ manager->num_freed = 0; ++ manager->num_active = 0; ++ manager->total = 0; ++ manager->cur = 0; ++ manager->max = 0; ++ ++ return 0; ++} ++ ++void dwc_memory_debug_stop(void) ++{ ++ struct allocation *a; ++ ++ dwc_memory_debug_report(); ++ ++ DWC_CIRCLEQ_FOREACH(a, &manager->allocations, entry) { ++ DWC_ERROR("Memory leaked from %s:%d\n", a->func, a->line); ++ free_allocation(a->ctx, a->addr, NULL, -1); ++ } ++ ++ __DWC_FREE(manager->mem_ctx, manager); ++} ++ ++void dwc_memory_debug_report(void) ++{ ++ struct allocation *a; ++ ++ DWC_PRINTF("\n\n\n----------------- Memory Debugging Report -----------------\n\n"); ++ DWC_PRINTF("Num Allocations = %d\n", manager->num); ++ DWC_PRINTF("Freed = %d\n", manager->num_freed); ++ DWC_PRINTF("Active = %d\n", manager->num_active); ++ DWC_PRINTF("Current Memory Used = %d\n", manager->cur); ++ DWC_PRINTF("Total Memory Used = %d\n", manager->total); ++ DWC_PRINTF("Maximum Memory Used at Once = %d\n", manager->max); ++ DWC_PRINTF("Unfreed allocations:\n"); ++ ++ DWC_CIRCLEQ_FOREACH(a, &manager->allocations, entry) { ++ DWC_PRINTF(" addr=%p, size=%d from %s:%d, DMA=%d\n", ++ a->addr, a->size, a->func, a->line, a->dma); ++ } ++} ++ ++/* The replacement functions */ ++void *dwc_alloc_debug(void *mem_ctx, uint32_t size, char const *func, int line) ++{ ++ void *addr = __DWC_ALLOC(mem_ctx, size); ++ ++ if (!addr) { ++ return NULL; ++ } ++ ++ if (add_allocation(mem_ctx, size, func, line, addr, 0)) { ++ __DWC_FREE(mem_ctx, addr); ++ return NULL; ++ } ++ ++ return addr; ++} ++ ++void *dwc_alloc_atomic_debug(void *mem_ctx, uint32_t size, char const *func, ++ int line) ++{ ++ void *addr = __DWC_ALLOC_ATOMIC(mem_ctx, size); ++ ++ if (!addr) { ++ return NULL; ++ } ++ ++ if (add_allocation(mem_ctx, size, func, line, addr, 0)) { ++ __DWC_FREE(mem_ctx, addr); ++ return NULL; ++ } ++ ++ return addr; ++} ++ ++void dwc_free_debug(void *mem_ctx, void *addr, char const *func, int line) ++{ ++ free_allocation(mem_ctx, addr, func, line); ++ __DWC_FREE(mem_ctx, addr); ++} ++ ++void *dwc_dma_alloc_debug(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr, ++ char const *func, int line) ++{ ++ void *addr = __DWC_DMA_ALLOC(dma_ctx, size, dma_addr); ++ ++ if (!addr) { ++ return NULL; ++ } ++ ++ if (add_allocation(dma_ctx, size, func, line, addr, 1)) { ++ __DWC_DMA_FREE(dma_ctx, size, addr, *dma_addr); ++ return NULL; ++ } ++ ++ return addr; ++} ++ ++void *dwc_dma_alloc_atomic_debug(void *dma_ctx, uint32_t size, ++ dwc_dma_t *dma_addr, char const *func, int line) ++{ ++ void *addr = __DWC_DMA_ALLOC_ATOMIC(dma_ctx, size, dma_addr); ++ ++ if (!addr) { ++ return NULL; ++ } ++ ++ if (add_allocation(dma_ctx, size, func, line, addr, 1)) { ++ __DWC_DMA_FREE(dma_ctx, size, addr, *dma_addr); ++ return NULL; ++ } ++ ++ return addr; ++} ++ ++void dwc_dma_free_debug(void *dma_ctx, uint32_t size, void *virt_addr, ++ dwc_dma_t dma_addr, char const *func, int line) ++{ ++ free_allocation(dma_ctx, virt_addr, func, line); ++ __DWC_DMA_FREE(dma_ctx, size, virt_addr, dma_addr); ++} ++ ++#endif /* DWC_DEBUG_MEMORY */ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_modpow.c +@@ -0,0 +1,636 @@ ++/* Bignum routines adapted from PUTTY sources. PuTTY copyright notice follows. ++ * ++ * PuTTY is copyright 1997-2007 Simon Tatham. ++ * ++ * Portions copyright Robert de Bath, Joris van Rantwijk, Delian ++ * Delchev, Andreas Schultz, Jeroen Massar, Wez Furlong, Nicolas Barry, ++ * Justin Bradford, Ben Harris, Malcolm Smith, Ahmad Khalifa, Markus ++ * Kuhn, and CORE SDI S.A. ++ * ++ * Permission is hereby granted, free of charge, to any person ++ * obtaining a copy of this software and associated documentation files ++ * (the "Software"), to deal in the Software without restriction, ++ * including without limitation the rights to use, copy, modify, merge, ++ * publish, distribute, sublicense, and/or sell copies of the Software, ++ * and to permit persons to whom the Software is furnished to do so, ++ * subject to the following conditions: ++ * ++ * The above copyright notice and this permission notice shall be ++ * included in all copies or substantial portions of the Software. ++ ++ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, ++ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF ++ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND ++ * NONINFRINGEMENT. IN NO EVENT SHALL THE COPYRIGHT HOLDERS BE LIABLE ++ * FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF ++ * CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION ++ * WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. ++ * ++ */ ++#ifdef DWC_CRYPTOLIB ++ ++#ifndef CONFIG_MACH_IPMATE ++ ++#include "dwc_modpow.h" ++ ++#define BIGNUM_INT_MASK 0xFFFFFFFFUL ++#define BIGNUM_TOP_BIT 0x80000000UL ++#define BIGNUM_INT_BITS 32 ++ ++ ++static void *snmalloc(void *mem_ctx, size_t n, size_t size) ++{ ++ void *p; ++ size *= n; ++ if (size == 0) size = 1; ++ p = dwc_alloc(mem_ctx, size); ++ return p; ++} ++ ++#define snewn(ctx, n, type) ((type *)snmalloc((ctx), (n), sizeof(type))) ++#define sfree dwc_free ++ ++/* ++ * Usage notes: ++ * * Do not call the DIVMOD_WORD macro with expressions such as array ++ * subscripts, as some implementations object to this (see below). ++ * * Note that none of the division methods below will cope if the ++ * quotient won't fit into BIGNUM_INT_BITS. Callers should be careful ++ * to avoid this case. ++ * If this condition occurs, in the case of the x86 DIV instruction, ++ * an overflow exception will occur, which (according to a correspondent) ++ * will manifest on Windows as something like ++ * 0xC0000095: Integer overflow ++ * The C variant won't give the right answer, either. ++ */ ++ ++#define MUL_WORD(w1, w2) ((BignumDblInt)w1 * w2) ++ ++#if defined __GNUC__ && defined __i386__ ++#define DIVMOD_WORD(q, r, hi, lo, w) \ ++ __asm__("div %2" : \ ++ "=d" (r), "=a" (q) : \ ++ "r" (w), "d" (hi), "a" (lo)) ++#else ++#define DIVMOD_WORD(q, r, hi, lo, w) do { \ ++ BignumDblInt n = (((BignumDblInt)hi) << BIGNUM_INT_BITS) | lo; \ ++ q = n / w; \ ++ r = n % w; \ ++} while (0) ++#endif ++ ++// q = n / w; ++// r = n % w; ++ ++#define BIGNUM_INT_BYTES (BIGNUM_INT_BITS / 8) ++ ++#define BIGNUM_INTERNAL ++ ++static Bignum newbn(void *mem_ctx, int length) ++{ ++ Bignum b = snewn(mem_ctx, length + 1, BignumInt); ++ //if (!b) ++ //abort(); /* FIXME */ ++ DWC_MEMSET(b, 0, (length + 1) * sizeof(*b)); ++ b[0] = length; ++ return b; ++} ++ ++void freebn(void *mem_ctx, Bignum b) ++{ ++ /* ++ * Burn the evidence, just in case. ++ */ ++ DWC_MEMSET(b, 0, sizeof(b[0]) * (b[0] + 1)); ++ sfree(mem_ctx, b); ++} ++ ++/* ++ * Compute c = a * b. ++ * Input is in the first len words of a and b. ++ * Result is returned in the first 2*len words of c. ++ */ ++static void internal_mul(BignumInt *a, BignumInt *b, ++ BignumInt *c, int len) ++{ ++ int i, j; ++ BignumDblInt t; ++ ++ for (j = 0; j < 2 * len; j++) ++ c[j] = 0; ++ ++ for (i = len - 1; i >= 0; i--) { ++ t = 0; ++ for (j = len - 1; j >= 0; j--) { ++ t += MUL_WORD(a[i], (BignumDblInt) b[j]); ++ t += (BignumDblInt) c[i + j + 1]; ++ c[i + j + 1] = (BignumInt) t; ++ t = t >> BIGNUM_INT_BITS; ++ } ++ c[i] = (BignumInt) t; ++ } ++} ++ ++static void internal_add_shifted(BignumInt *number, ++ unsigned n, int shift) ++{ ++ int word = 1 + (shift / BIGNUM_INT_BITS); ++ int bshift = shift % BIGNUM_INT_BITS; ++ BignumDblInt addend; ++ ++ addend = (BignumDblInt)n << bshift; ++ ++ while (addend) { ++ addend += number[word]; ++ number[word] = (BignumInt) addend & BIGNUM_INT_MASK; ++ addend >>= BIGNUM_INT_BITS; ++ word++; ++ } ++} ++ ++/* ++ * Compute a = a % m. ++ * Input in first alen words of a and first mlen words of m. ++ * Output in first alen words of a ++ * (of which first alen-mlen words will be zero). ++ * The MSW of m MUST have its high bit set. ++ * Quotient is accumulated in the `quotient' array, which is a Bignum ++ * rather than the internal bigendian format. Quotient parts are shifted ++ * left by `qshift' before adding into quot. ++ */ ++static void internal_mod(BignumInt *a, int alen, ++ BignumInt *m, int mlen, ++ BignumInt *quot, int qshift) ++{ ++ BignumInt m0, m1; ++ unsigned int h; ++ int i, k; ++ ++ m0 = m[0]; ++ if (mlen > 1) ++ m1 = m[1]; ++ else ++ m1 = 0; ++ ++ for (i = 0; i <= alen - mlen; i++) { ++ BignumDblInt t; ++ unsigned int q, r, c, ai1; ++ ++ if (i == 0) { ++ h = 0; ++ } else { ++ h = a[i - 1]; ++ a[i - 1] = 0; ++ } ++ ++ if (i == alen - 1) ++ ai1 = 0; ++ else ++ ai1 = a[i + 1]; ++ ++ /* Find q = h:a[i] / m0 */ ++ if (h >= m0) { ++ /* ++ * Special case. ++ * ++ * To illustrate it, suppose a BignumInt is 8 bits, and ++ * we are dividing (say) A1:23:45:67 by A1:B2:C3. Then ++ * our initial division will be 0xA123 / 0xA1, which ++ * will give a quotient of 0x100 and a divide overflow. ++ * However, the invariants in this division algorithm ++ * are not violated, since the full number A1:23:... is ++ * _less_ than the quotient prefix A1:B2:... and so the ++ * following correction loop would have sorted it out. ++ * ++ * In this situation we set q to be the largest ++ * quotient we _can_ stomach (0xFF, of course). ++ */ ++ q = BIGNUM_INT_MASK; ++ } else { ++ /* Macro doesn't want an array subscript expression passed ++ * into it (see definition), so use a temporary. */ ++ BignumInt tmplo = a[i]; ++ DIVMOD_WORD(q, r, h, tmplo, m0); ++ ++ /* Refine our estimate of q by looking at ++ h:a[i]:a[i+1] / m0:m1 */ ++ t = MUL_WORD(m1, q); ++ if (t > ((BignumDblInt) r << BIGNUM_INT_BITS) + ai1) { ++ q--; ++ t -= m1; ++ r = (r + m0) & BIGNUM_INT_MASK; /* overflow? */ ++ if (r >= (BignumDblInt) m0 && ++ t > ((BignumDblInt) r << BIGNUM_INT_BITS) + ai1) q--; ++ } ++ } ++ ++ /* Subtract q * m from a[i...] */ ++ c = 0; ++ for (k = mlen - 1; k >= 0; k--) { ++ t = MUL_WORD(q, m[k]); ++ t += c; ++ c = (unsigned)(t >> BIGNUM_INT_BITS); ++ if ((BignumInt) t > a[i + k]) ++ c++; ++ a[i + k] -= (BignumInt) t; ++ } ++ ++ /* Add back m in case of borrow */ ++ if (c != h) { ++ t = 0; ++ for (k = mlen - 1; k >= 0; k--) { ++ t += m[k]; ++ t += a[i + k]; ++ a[i + k] = (BignumInt) t; ++ t = t >> BIGNUM_INT_BITS; ++ } ++ q--; ++ } ++ if (quot) ++ internal_add_shifted(quot, q, qshift + BIGNUM_INT_BITS * (alen - mlen - i)); ++ } ++} ++ ++/* ++ * Compute p % mod. ++ * The most significant word of mod MUST be non-zero. ++ * We assume that the result array is the same size as the mod array. ++ * We optionally write out a quotient if `quotient' is non-NULL. ++ * We can avoid writing out the result if `result' is NULL. ++ */ ++void bigdivmod(void *mem_ctx, Bignum p, Bignum mod, Bignum result, Bignum quotient) ++{ ++ BignumInt *n, *m; ++ int mshift; ++ int plen, mlen, i, j; ++ ++ /* Allocate m of size mlen, copy mod to m */ ++ /* We use big endian internally */ ++ mlen = mod[0]; ++ m = snewn(mem_ctx, mlen, BignumInt); ++ //if (!m) ++ //abort(); /* FIXME */ ++ for (j = 0; j < mlen; j++) ++ m[j] = mod[mod[0] - j]; ++ ++ /* Shift m left to make msb bit set */ ++ for (mshift = 0; mshift < BIGNUM_INT_BITS-1; mshift++) ++ if ((m[0] << mshift) & BIGNUM_TOP_BIT) ++ break; ++ if (mshift) { ++ for (i = 0; i < mlen - 1; i++) ++ m[i] = (m[i] << mshift) | (m[i + 1] >> (BIGNUM_INT_BITS - mshift)); ++ m[mlen - 1] = m[mlen - 1] << mshift; ++ } ++ ++ plen = p[0]; ++ /* Ensure plen > mlen */ ++ if (plen <= mlen) ++ plen = mlen + 1; ++ ++ /* Allocate n of size plen, copy p to n */ ++ n = snewn(mem_ctx, plen, BignumInt); ++ //if (!n) ++ //abort(); /* FIXME */ ++ for (j = 0; j < plen; j++) ++ n[j] = 0; ++ for (j = 1; j <= (int)p[0]; j++) ++ n[plen - j] = p[j]; ++ ++ /* Main computation */ ++ internal_mod(n, plen, m, mlen, quotient, mshift); ++ ++ /* Fixup result in case the modulus was shifted */ ++ if (mshift) { ++ for (i = plen - mlen - 1; i < plen - 1; i++) ++ n[i] = (n[i] << mshift) | (n[i + 1] >> (BIGNUM_INT_BITS - mshift)); ++ n[plen - 1] = n[plen - 1] << mshift; ++ internal_mod(n, plen, m, mlen, quotient, 0); ++ for (i = plen - 1; i >= plen - mlen; i--) ++ n[i] = (n[i] >> mshift) | (n[i - 1] << (BIGNUM_INT_BITS - mshift)); ++ } ++ ++ /* Copy result to buffer */ ++ if (result) { ++ for (i = 1; i <= (int)result[0]; i++) { ++ int j = plen - i; ++ result[i] = j >= 0 ? n[j] : 0; ++ } ++ } ++ ++ /* Free temporary arrays */ ++ for (i = 0; i < mlen; i++) ++ m[i] = 0; ++ sfree(mem_ctx, m); ++ for (i = 0; i < plen; i++) ++ n[i] = 0; ++ sfree(mem_ctx, n); ++} ++ ++/* ++ * Simple remainder. ++ */ ++Bignum bigmod(void *mem_ctx, Bignum a, Bignum b) ++{ ++ Bignum r = newbn(mem_ctx, b[0]); ++ bigdivmod(mem_ctx, a, b, r, NULL); ++ return r; ++} ++ ++/* ++ * Compute (base ^ exp) % mod. ++ */ ++Bignum dwc_modpow(void *mem_ctx, Bignum base_in, Bignum exp, Bignum mod) ++{ ++ BignumInt *a, *b, *n, *m; ++ int mshift; ++ int mlen, i, j; ++ Bignum base, result; ++ ++ /* ++ * The most significant word of mod needs to be non-zero. It ++ * should already be, but let's make sure. ++ */ ++ //assert(mod[mod[0]] != 0); ++ ++ /* ++ * Make sure the base is smaller than the modulus, by reducing ++ * it modulo the modulus if not. ++ */ ++ base = bigmod(mem_ctx, base_in, mod); ++ ++ /* Allocate m of size mlen, copy mod to m */ ++ /* We use big endian internally */ ++ mlen = mod[0]; ++ m = snewn(mem_ctx, mlen, BignumInt); ++ //if (!m) ++ //abort(); /* FIXME */ ++ for (j = 0; j < mlen; j++) ++ m[j] = mod[mod[0] - j]; ++ ++ /* Shift m left to make msb bit set */ ++ for (mshift = 0; mshift < BIGNUM_INT_BITS - 1; mshift++) ++ if ((m[0] << mshift) & BIGNUM_TOP_BIT) ++ break; ++ if (mshift) { ++ for (i = 0; i < mlen - 1; i++) ++ m[i] = ++ (m[i] << mshift) | (m[i + 1] >> ++ (BIGNUM_INT_BITS - mshift)); ++ m[mlen - 1] = m[mlen - 1] << mshift; ++ } ++ ++ /* Allocate n of size mlen, copy base to n */ ++ n = snewn(mem_ctx, mlen, BignumInt); ++ //if (!n) ++ //abort(); /* FIXME */ ++ i = mlen - base[0]; ++ for (j = 0; j < i; j++) ++ n[j] = 0; ++ for (j = 0; j < base[0]; j++) ++ n[i + j] = base[base[0] - j]; ++ ++ /* Allocate a and b of size 2*mlen. Set a = 1 */ ++ a = snewn(mem_ctx, 2 * mlen, BignumInt); ++ //if (!a) ++ //abort(); /* FIXME */ ++ b = snewn(mem_ctx, 2 * mlen, BignumInt); ++ //if (!b) ++ //abort(); /* FIXME */ ++ for (i = 0; i < 2 * mlen; i++) ++ a[i] = 0; ++ a[2 * mlen - 1] = 1; ++ ++ /* Skip leading zero bits of exp. */ ++ i = 0; ++ j = BIGNUM_INT_BITS - 1; ++ while (i < exp[0] && (exp[exp[0] - i] & (1 << j)) == 0) { ++ j--; ++ if (j < 0) { ++ i++; ++ j = BIGNUM_INT_BITS - 1; ++ } ++ } ++ ++ /* Main computation */ ++ while (i < exp[0]) { ++ while (j >= 0) { ++ internal_mul(a + mlen, a + mlen, b, mlen); ++ internal_mod(b, mlen * 2, m, mlen, NULL, 0); ++ if ((exp[exp[0] - i] & (1 << j)) != 0) { ++ internal_mul(b + mlen, n, a, mlen); ++ internal_mod(a, mlen * 2, m, mlen, NULL, 0); ++ } else { ++ BignumInt *t; ++ t = a; ++ a = b; ++ b = t; ++ } ++ j--; ++ } ++ i++; ++ j = BIGNUM_INT_BITS - 1; ++ } ++ ++ /* Fixup result in case the modulus was shifted */ ++ if (mshift) { ++ for (i = mlen - 1; i < 2 * mlen - 1; i++) ++ a[i] = ++ (a[i] << mshift) | (a[i + 1] >> ++ (BIGNUM_INT_BITS - mshift)); ++ a[2 * mlen - 1] = a[2 * mlen - 1] << mshift; ++ internal_mod(a, mlen * 2, m, mlen, NULL, 0); ++ for (i = 2 * mlen - 1; i >= mlen; i--) ++ a[i] = ++ (a[i] >> mshift) | (a[i - 1] << ++ (BIGNUM_INT_BITS - mshift)); ++ } ++ ++ /* Copy result to buffer */ ++ result = newbn(mem_ctx, mod[0]); ++ for (i = 0; i < mlen; i++) ++ result[result[0] - i] = a[i + mlen]; ++ while (result[0] > 1 && result[result[0]] == 0) ++ result[0]--; ++ ++ /* Free temporary arrays */ ++ for (i = 0; i < 2 * mlen; i++) ++ a[i] = 0; ++ sfree(mem_ctx, a); ++ for (i = 0; i < 2 * mlen; i++) ++ b[i] = 0; ++ sfree(mem_ctx, b); ++ for (i = 0; i < mlen; i++) ++ m[i] = 0; ++ sfree(mem_ctx, m); ++ for (i = 0; i < mlen; i++) ++ n[i] = 0; ++ sfree(mem_ctx, n); ++ ++ freebn(mem_ctx, base); ++ ++ return result; ++} ++ ++ ++#ifdef UNITTEST ++ ++static __u32 dh_p[] = { ++ 96, ++ 0xFFFFFFFF, ++ 0xFFFFFFFF, ++ 0xA93AD2CA, ++ 0x4B82D120, ++ 0xE0FD108E, ++ 0x43DB5BFC, ++ 0x74E5AB31, ++ 0x08E24FA0, ++ 0xBAD946E2, ++ 0x770988C0, ++ 0x7A615D6C, ++ 0xBBE11757, ++ 0x177B200C, ++ 0x521F2B18, ++ 0x3EC86A64, ++ 0xD8760273, ++ 0xD98A0864, ++ 0xF12FFA06, ++ 0x1AD2EE6B, ++ 0xCEE3D226, ++ 0x4A25619D, ++ 0x1E8C94E0, ++ 0xDB0933D7, ++ 0xABF5AE8C, ++ 0xA6E1E4C7, ++ 0xB3970F85, ++ 0x5D060C7D, ++ 0x8AEA7157, ++ 0x58DBEF0A, ++ 0xECFB8504, ++ 0xDF1CBA64, ++ 0xA85521AB, ++ 0x04507A33, ++ 0xAD33170D, ++ 0x8AAAC42D, ++ 0x15728E5A, ++ 0x98FA0510, ++ 0x15D22618, ++ 0xEA956AE5, ++ 0x3995497C, ++ 0x95581718, ++ 0xDE2BCBF6, ++ 0x6F4C52C9, ++ 0xB5C55DF0, ++ 0xEC07A28F, ++ 0x9B2783A2, ++ 0x180E8603, ++ 0xE39E772C, ++ 0x2E36CE3B, ++ 0x32905E46, ++ 0xCA18217C, ++ 0xF1746C08, ++ 0x4ABC9804, ++ 0x670C354E, ++ 0x7096966D, ++ 0x9ED52907, ++ 0x208552BB, ++ 0x1C62F356, ++ 0xDCA3AD96, ++ 0x83655D23, ++ 0xFD24CF5F, ++ 0x69163FA8, ++ 0x1C55D39A, ++ 0x98DA4836, ++ 0xA163BF05, ++ 0xC2007CB8, ++ 0xECE45B3D, ++ 0x49286651, ++ 0x7C4B1FE6, ++ 0xAE9F2411, ++ 0x5A899FA5, ++ 0xEE386BFB, ++ 0xF406B7ED, ++ 0x0BFF5CB6, ++ 0xA637ED6B, ++ 0xF44C42E9, ++ 0x625E7EC6, ++ 0xE485B576, ++ 0x6D51C245, ++ 0x4FE1356D, ++ 0xF25F1437, ++ 0x302B0A6D, ++ 0xCD3A431B, ++ 0xEF9519B3, ++ 0x8E3404DD, ++ 0x514A0879, ++ 0x3B139B22, ++ 0x020BBEA6, ++ 0x8A67CC74, ++ 0x29024E08, ++ 0x80DC1CD1, ++ 0xC4C6628B, ++ 0x2168C234, ++ 0xC90FDAA2, ++ 0xFFFFFFFF, ++ 0xFFFFFFFF, ++}; ++ ++static __u32 dh_a[] = { ++ 8, ++ 0xdf367516, ++ 0x86459caa, ++ 0xe2d459a4, ++ 0xd910dae0, ++ 0x8a8b5e37, ++ 0x67ab31c6, ++ 0xf0b55ea9, ++ 0x440051d6, ++}; ++ ++static __u32 dh_b[] = { ++ 8, ++ 0xded92656, ++ 0xe07a048a, ++ 0x6fa452cd, ++ 0x2df89d30, ++ 0xc75f1b0f, ++ 0x8ce3578f, ++ 0x7980a324, ++ 0x5daec786, ++}; ++ ++static __u32 dh_g[] = { ++ 1, ++ 2, ++}; ++ ++int main(void) ++{ ++ int i; ++ __u32 *k; ++ k = dwc_modpow(NULL, dh_g, dh_a, dh_p); ++ ++ printf("\n\n"); ++ for (i=0; i> 16; ++ printf("%04x %04x ", m, l); ++ if (!((i + 1)%13)) printf("\n"); ++ } ++ printf("\n\n"); ++ ++ if ((k[0] == 0x60) && (k[1] == 0x28e490e5) && (k[0x60] == 0x5a0d3d4e)) { ++ printf("PASS\n\n"); ++ } ++ else { ++ printf("FAIL\n\n"); ++ } ++ ++} ++ ++#endif /* UNITTEST */ ++ ++#endif /* CONFIG_MACH_IPMATE */ ++ ++#endif /*DWC_CRYPTOLIB */ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_modpow.h +@@ -0,0 +1,34 @@ ++/* ++ * dwc_modpow.h ++ * See dwc_modpow.c for license and changes ++ */ ++#ifndef _DWC_MODPOW_H ++#define _DWC_MODPOW_H ++ ++#ifdef __cplusplus ++extern "C" { ++#endif ++ ++#include "dwc_os.h" ++ ++/** @file ++ * ++ * This file defines the module exponentiation function which is only used ++ * internally by the DWC UWB modules for calculation of PKs during numeric ++ * association. The routine is taken from the PUTTY, an open source terminal ++ * emulator. The PUTTY License is preserved in the dwc_modpow.c file. ++ * ++ */ ++ ++typedef uint32_t BignumInt; ++typedef uint64_t BignumDblInt; ++typedef BignumInt *Bignum; ++ ++/* Compute modular exponentiaion */ ++extern Bignum dwc_modpow(void *mem_ctx, Bignum base_in, Bignum exp, Bignum mod); ++ ++#ifdef __cplusplus ++} ++#endif ++ ++#endif /* _LINUX_BIGNUM_H */ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_notifier.c +@@ -0,0 +1,319 @@ ++#ifdef DWC_NOTIFYLIB ++ ++#include "dwc_notifier.h" ++#include "dwc_list.h" ++ ++typedef struct dwc_observer { ++ void *observer; ++ dwc_notifier_callback_t callback; ++ void *data; ++ char *notification; ++ DWC_CIRCLEQ_ENTRY(dwc_observer) list_entry; ++} observer_t; ++ ++DWC_CIRCLEQ_HEAD(observer_queue, dwc_observer); ++ ++typedef struct dwc_notifier { ++ void *mem_ctx; ++ void *object; ++ struct observer_queue observers; ++ DWC_CIRCLEQ_ENTRY(dwc_notifier) list_entry; ++} notifier_t; ++ ++DWC_CIRCLEQ_HEAD(notifier_queue, dwc_notifier); ++ ++typedef struct manager { ++ void *mem_ctx; ++ void *wkq_ctx; ++ dwc_workq_t *wq; ++// dwc_mutex_t *mutex; ++ struct notifier_queue notifiers; ++} manager_t; ++ ++static manager_t *manager = NULL; ++ ++static int create_manager(void *mem_ctx, void *wkq_ctx) ++{ ++ manager = dwc_alloc(mem_ctx, sizeof(manager_t)); ++ if (!manager) { ++ return -DWC_E_NO_MEMORY; ++ } ++ ++ DWC_CIRCLEQ_INIT(&manager->notifiers); ++ ++ manager->wq = dwc_workq_alloc(wkq_ctx, "DWC Notification WorkQ"); ++ if (!manager->wq) { ++ return -DWC_E_NO_MEMORY; ++ } ++ ++ return 0; ++} ++ ++static void free_manager(void) ++{ ++ dwc_workq_free(manager->wq); ++ ++ /* All notifiers must have unregistered themselves before this module ++ * can be removed. Hitting this assertion indicates a programmer ++ * error. */ ++ DWC_ASSERT(DWC_CIRCLEQ_EMPTY(&manager->notifiers), ++ "Notification manager being freed before all notifiers have been removed"); ++ dwc_free(manager->mem_ctx, manager); ++} ++ ++#ifdef DEBUG ++static void dump_manager(void) ++{ ++ notifier_t *n; ++ observer_t *o; ++ ++ DWC_ASSERT(manager, "Notification manager not found"); ++ ++ DWC_DEBUG("List of all notifiers and observers:\n"); ++ DWC_CIRCLEQ_FOREACH(n, &manager->notifiers, list_entry) { ++ DWC_DEBUG("Notifier %p has observers:\n", n->object); ++ DWC_CIRCLEQ_FOREACH(o, &n->observers, list_entry) { ++ DWC_DEBUG(" %p watching %s\n", o->observer, o->notification); ++ } ++ } ++} ++#else ++#define dump_manager(...) ++#endif ++ ++static observer_t *alloc_observer(void *mem_ctx, void *observer, char *notification, ++ dwc_notifier_callback_t callback, void *data) ++{ ++ observer_t *new_observer = dwc_alloc(mem_ctx, sizeof(observer_t)); ++ ++ if (!new_observer) { ++ return NULL; ++ } ++ ++ DWC_CIRCLEQ_INIT_ENTRY(new_observer, list_entry); ++ new_observer->observer = observer; ++ new_observer->notification = notification; ++ new_observer->callback = callback; ++ new_observer->data = data; ++ return new_observer; ++} ++ ++static void free_observer(void *mem_ctx, observer_t *observer) ++{ ++ dwc_free(mem_ctx, observer); ++} ++ ++static notifier_t *alloc_notifier(void *mem_ctx, void *object) ++{ ++ notifier_t *notifier; ++ ++ if (!object) { ++ return NULL; ++ } ++ ++ notifier = dwc_alloc(mem_ctx, sizeof(notifier_t)); ++ if (!notifier) { ++ return NULL; ++ } ++ ++ DWC_CIRCLEQ_INIT(¬ifier->observers); ++ DWC_CIRCLEQ_INIT_ENTRY(notifier, list_entry); ++ ++ notifier->mem_ctx = mem_ctx; ++ notifier->object = object; ++ return notifier; ++} ++ ++static void free_notifier(notifier_t *notifier) ++{ ++ observer_t *observer; ++ ++ DWC_CIRCLEQ_FOREACH(observer, ¬ifier->observers, list_entry) { ++ free_observer(notifier->mem_ctx, observer); ++ } ++ ++ dwc_free(notifier->mem_ctx, notifier); ++} ++ ++static notifier_t *find_notifier(void *object) ++{ ++ notifier_t *notifier; ++ ++ DWC_ASSERT(manager, "Notification manager not found"); ++ ++ if (!object) { ++ return NULL; ++ } ++ ++ DWC_CIRCLEQ_FOREACH(notifier, &manager->notifiers, list_entry) { ++ if (notifier->object == object) { ++ return notifier; ++ } ++ } ++ ++ return NULL; ++} ++ ++int dwc_alloc_notification_manager(void *mem_ctx, void *wkq_ctx) ++{ ++ return create_manager(mem_ctx, wkq_ctx); ++} ++ ++void dwc_free_notification_manager(void) ++{ ++ free_manager(); ++} ++ ++dwc_notifier_t *dwc_register_notifier(void *mem_ctx, void *object) ++{ ++ notifier_t *notifier; ++ ++ DWC_ASSERT(manager, "Notification manager not found"); ++ ++ notifier = find_notifier(object); ++ if (notifier) { ++ DWC_ERROR("Notifier %p is already registered\n", object); ++ return NULL; ++ } ++ ++ notifier = alloc_notifier(mem_ctx, object); ++ if (!notifier) { ++ return NULL; ++ } ++ ++ DWC_CIRCLEQ_INSERT_TAIL(&manager->notifiers, notifier, list_entry); ++ ++ DWC_INFO("Notifier %p registered", object); ++ dump_manager(); ++ ++ return notifier; ++} ++ ++void dwc_unregister_notifier(dwc_notifier_t *notifier) ++{ ++ DWC_ASSERT(manager, "Notification manager not found"); ++ ++ if (!DWC_CIRCLEQ_EMPTY(¬ifier->observers)) { ++ observer_t *o; ++ ++ DWC_ERROR("Notifier %p has active observers when removing\n", notifier->object); ++ DWC_CIRCLEQ_FOREACH(o, ¬ifier->observers, list_entry) { ++ DWC_DEBUGC(" %p watching %s\n", o->observer, o->notification); ++ } ++ ++ DWC_ASSERT(DWC_CIRCLEQ_EMPTY(¬ifier->observers), ++ "Notifier %p has active observers when removing", notifier); ++ } ++ ++ DWC_CIRCLEQ_REMOVE_INIT(&manager->notifiers, notifier, list_entry); ++ free_notifier(notifier); ++ ++ DWC_INFO("Notifier unregistered"); ++ dump_manager(); ++} ++ ++/* Add an observer to observe the notifier for a particular state, event, or notification. */ ++int dwc_add_observer(void *observer, void *object, char *notification, ++ dwc_notifier_callback_t callback, void *data) ++{ ++ notifier_t *notifier = find_notifier(object); ++ observer_t *new_observer; ++ ++ if (!notifier) { ++ DWC_ERROR("Notifier %p is not found when adding observer\n", object); ++ return -DWC_E_INVALID; ++ } ++ ++ new_observer = alloc_observer(notifier->mem_ctx, observer, notification, callback, data); ++ if (!new_observer) { ++ return -DWC_E_NO_MEMORY; ++ } ++ ++ DWC_CIRCLEQ_INSERT_TAIL(¬ifier->observers, new_observer, list_entry); ++ ++ DWC_INFO("Added observer %p to notifier %p observing notification %s, callback=%p, data=%p", ++ observer, object, notification, callback, data); ++ ++ dump_manager(); ++ return 0; ++} ++ ++int dwc_remove_observer(void *observer) ++{ ++ notifier_t *n; ++ ++ DWC_ASSERT(manager, "Notification manager not found"); ++ ++ DWC_CIRCLEQ_FOREACH(n, &manager->notifiers, list_entry) { ++ observer_t *o; ++ observer_t *o2; ++ ++ DWC_CIRCLEQ_FOREACH_SAFE(o, o2, &n->observers, list_entry) { ++ if (o->observer == observer) { ++ DWC_CIRCLEQ_REMOVE_INIT(&n->observers, o, list_entry); ++ DWC_INFO("Removing observer %p from notifier %p watching notification %s:", ++ o->observer, n->object, o->notification); ++ free_observer(n->mem_ctx, o); ++ } ++ } ++ } ++ ++ dump_manager(); ++ return 0; ++} ++ ++typedef struct callback_data { ++ void *mem_ctx; ++ dwc_notifier_callback_t cb; ++ void *observer; ++ void *data; ++ void *object; ++ char *notification; ++ void *notification_data; ++} cb_data_t; ++ ++static void cb_task(void *data) ++{ ++ cb_data_t *cb = (cb_data_t *)data; ++ ++ cb->cb(cb->object, cb->notification, cb->observer, cb->notification_data, cb->data); ++ dwc_free(cb->mem_ctx, cb); ++} ++ ++void dwc_notify(dwc_notifier_t *notifier, char *notification, void *notification_data) ++{ ++ observer_t *o; ++ ++ DWC_ASSERT(manager, "Notification manager not found"); ++ ++ DWC_CIRCLEQ_FOREACH(o, ¬ifier->observers, list_entry) { ++ int len = DWC_STRLEN(notification); ++ ++ if (DWC_STRLEN(o->notification) != len) { ++ continue; ++ } ++ ++ if (DWC_STRNCMP(o->notification, notification, len) == 0) { ++ cb_data_t *cb_data = dwc_alloc(notifier->mem_ctx, sizeof(cb_data_t)); ++ ++ if (!cb_data) { ++ DWC_ERROR("Failed to allocate callback data\n"); ++ return; ++ } ++ ++ cb_data->mem_ctx = notifier->mem_ctx; ++ cb_data->cb = o->callback; ++ cb_data->observer = o->observer; ++ cb_data->data = o->data; ++ cb_data->object = notifier->object; ++ cb_data->notification = notification; ++ cb_data->notification_data = notification_data; ++ DWC_DEBUGC("Observer found %p for notification %s\n", o->observer, notification); ++ DWC_WORKQ_SCHEDULE(manager->wq, cb_task, cb_data, ++ "Notify callback from %p for Notification %s, to observer %p", ++ cb_data->object, notification, cb_data->observer); ++ } ++ } ++} ++ ++#endif /* DWC_NOTIFYLIB */ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_notifier.h +@@ -0,0 +1,122 @@ ++ ++#ifndef __DWC_NOTIFIER_H__ ++#define __DWC_NOTIFIER_H__ ++ ++#ifdef __cplusplus ++extern "C" { ++#endif ++ ++#include "dwc_os.h" ++ ++/** @file ++ * ++ * A simple implementation of the Observer pattern. Any "module" can ++ * register as an observer or notifier. The notion of "module" is abstract and ++ * can mean anything used to identify either an observer or notifier. Usually ++ * it will be a pointer to a data structure which contains some state, ie an ++ * object. ++ * ++ * Before any notifiers can be added, the global notification manager must be ++ * brought up with dwc_alloc_notification_manager(). ++ * dwc_free_notification_manager() will bring it down and free all resources. ++ * These would typically be called upon module load and unload. The ++ * notification manager is a single global instance that handles all registered ++ * observable modules and observers so this should be done only once. ++ * ++ * A module can be observable by using Notifications to publicize some general ++ * information about it's state or operation. It does not care who listens, or ++ * even if anyone listens, or what they do with the information. The observable ++ * modules do not need to know any information about it's observers or their ++ * interface, or their state or data. ++ * ++ * Any module can register to emit Notifications. It should publish a list of ++ * notifications that it can emit and their behavior, such as when they will get ++ * triggered, and what information will be provided to the observer. Then it ++ * should register itself as an observable module. See dwc_register_notifier(). ++ * ++ * Any module can observe any observable, registered module, provided it has a ++ * handle to the other module and knows what notifications to observe. See ++ * dwc_add_observer(). ++ * ++ * A function of type dwc_notifier_callback_t is called whenever a notification ++ * is triggered with one or more observers observing it. This function is ++ * called in it's own process so it may sleep or block if needed. It is ++ * guaranteed to be called sometime after the notification has occurred and will ++ * be called once per each time the notification is triggered. It will NOT be ++ * called in the same process context used to trigger the notification. ++ * ++ * @section Limitiations ++ * ++ * Keep in mind that Notifications that can be triggered in rapid sucession may ++ * schedule too many processes too handle. Be aware of this limitation when ++ * designing to use notifications, and only add notifications for appropriate ++ * observable information. ++ * ++ * Also Notification callbacks are not synchronous. If you need to synchronize ++ * the behavior between module/observer you must use other means. And perhaps ++ * that will mean Notifications are not the proper solution. ++ */ ++ ++struct dwc_notifier; ++typedef struct dwc_notifier dwc_notifier_t; ++ ++/** The callback function must be of this type. ++ * ++ * @param object This is the object that is being observed. ++ * @param notification This is the notification that was triggered. ++ * @param observer This is the observer ++ * @param notification_data This is notification-specific data that the notifier ++ * has included in this notification. The value of this should be published in ++ * the documentation of the observable module with the notifications. ++ * @param user_data This is any custom data that the observer provided when ++ * adding itself as an observer to the notification. */ ++typedef void (*dwc_notifier_callback_t)(void *object, char *notification, void *observer, ++ void *notification_data, void *user_data); ++ ++/** Brings up the notification manager. */ ++extern int dwc_alloc_notification_manager(void *mem_ctx, void *wkq_ctx); ++/** Brings down the notification manager. */ ++extern void dwc_free_notification_manager(void); ++ ++/** This function registers an observable module. A dwc_notifier_t object is ++ * returned to the observable module. This is an opaque object that is used by ++ * the observable module to trigger notifications. This object should only be ++ * accessible to functions that are authorized to trigger notifications for this ++ * module. Observers do not need this object. */ ++extern dwc_notifier_t *dwc_register_notifier(void *mem_ctx, void *object); ++ ++/** This function unregisters an observable module. All observers have to be ++ * removed prior to unregistration. */ ++extern void dwc_unregister_notifier(dwc_notifier_t *notifier); ++ ++/** Add a module as an observer to the observable module. The observable module ++ * needs to have previously registered with the notification manager. ++ * ++ * @param observer The observer module ++ * @param object The module to observe ++ * @param notification The notification to observe ++ * @param callback The callback function to call ++ * @param user_data Any additional user data to pass into the callback function */ ++extern int dwc_add_observer(void *observer, void *object, char *notification, ++ dwc_notifier_callback_t callback, void *user_data); ++ ++/** Removes the specified observer from all notifications that it is currently ++ * observing. */ ++extern int dwc_remove_observer(void *observer); ++ ++/** This function triggers a Notification. It should be called by the ++ * observable module, or any module or library which the observable module ++ * allows to trigger notification on it's behalf. Such as the dwc_cc_t. ++ * ++ * dwc_notify is a non-blocking function. Callbacks are scheduled called in ++ * their own process context for each trigger. Callbacks can be blocking. ++ * dwc_notify can be called from interrupt context if needed. ++ * ++ */ ++void dwc_notify(dwc_notifier_t *notifier, char *notification, void *notification_data); ++ ++#ifdef __cplusplus ++} ++#endif ++ ++#endif /* __DWC_NOTIFIER_H__ */ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/dwc_os.h +@@ -0,0 +1,1276 @@ ++/* ========================================================================= ++ * $File: //dwh/usb_iip/dev/software/dwc_common_port_2/dwc_os.h $ ++ * $Revision: #14 $ ++ * $Date: 2010/11/04 $ ++ * $Change: 1621695 $ ++ * ++ * Synopsys Portability Library Software and documentation ++ * (hereinafter, "Software") is an Unsupported proprietary work of ++ * Synopsys, Inc. unless otherwise expressly agreed to in writing ++ * between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product ++ * under any End User Software License Agreement or Agreement for ++ * Licensed Product with Synopsys or any supplement thereto. You are ++ * permitted to use and redistribute this Software in source and binary ++ * forms, with or without modification, provided that redistributions ++ * of source code must retain this notice. You may not view, use, ++ * disclose, copy or distribute this file or any information contained ++ * herein except pursuant to this license grant from Synopsys. If you ++ * do not agree with this notice, including the disclaimer below, then ++ * you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" ++ * BASIS AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT ++ * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS ++ * FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. IN NO EVENT SHALL ++ * SYNOPSYS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY ++ * OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE ++ * USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================= */ ++#ifndef _DWC_OS_H_ ++#define _DWC_OS_H_ ++ ++#ifdef __cplusplus ++extern "C" { ++#endif ++ ++/** @file ++ * ++ * DWC portability library, low level os-wrapper functions ++ * ++ */ ++ ++/* These basic types need to be defined by some OS header file or custom header ++ * file for your specific target architecture. ++ * ++ * uint8_t, int8_t, uint16_t, int16_t, uint32_t, int32_t, uint64_t, int64_t ++ * ++ * Any custom or alternate header file must be added and enabled here. ++ */ ++ ++#ifdef DWC_LINUX ++# include ++# ifdef CONFIG_DEBUG_MUTEXES ++# include ++# endif ++# include ++# include ++# include ++#endif ++ ++#if defined(DWC_FREEBSD) || defined(DWC_NETBSD) ++# include ++#endif ++ ++ ++/** @name Primitive Types and Values */ ++ ++/** We define a boolean type for consistency. Can be either YES or NO */ ++typedef uint8_t dwc_bool_t; ++#define YES 1 ++#define NO 0 ++ ++#ifdef DWC_LINUX ++ ++/** @name Error Codes */ ++#define DWC_E_INVALID EINVAL ++#define DWC_E_NO_MEMORY ENOMEM ++#define DWC_E_NO_DEVICE ENODEV ++#define DWC_E_NOT_SUPPORTED EOPNOTSUPP ++#define DWC_E_TIMEOUT ETIMEDOUT ++#define DWC_E_BUSY EBUSY ++#define DWC_E_AGAIN EAGAIN ++#define DWC_E_RESTART ERESTART ++#define DWC_E_ABORT ECONNABORTED ++#define DWC_E_SHUTDOWN ESHUTDOWN ++#define DWC_E_NO_DATA ENODATA ++#define DWC_E_DISCONNECT ECONNRESET ++#define DWC_E_UNKNOWN EINVAL ++#define DWC_E_NO_STREAM_RES ENOSR ++#define DWC_E_COMMUNICATION ECOMM ++#define DWC_E_OVERFLOW EOVERFLOW ++#define DWC_E_PROTOCOL EPROTO ++#define DWC_E_IN_PROGRESS EINPROGRESS ++#define DWC_E_PIPE EPIPE ++#define DWC_E_IO EIO ++#define DWC_E_NO_SPACE ENOSPC ++ ++#else ++ ++/** @name Error Codes */ ++#define DWC_E_INVALID 1001 ++#define DWC_E_NO_MEMORY 1002 ++#define DWC_E_NO_DEVICE 1003 ++#define DWC_E_NOT_SUPPORTED 1004 ++#define DWC_E_TIMEOUT 1005 ++#define DWC_E_BUSY 1006 ++#define DWC_E_AGAIN 1007 ++#define DWC_E_RESTART 1008 ++#define DWC_E_ABORT 1009 ++#define DWC_E_SHUTDOWN 1010 ++#define DWC_E_NO_DATA 1011 ++#define DWC_E_DISCONNECT 2000 ++#define DWC_E_UNKNOWN 3000 ++#define DWC_E_NO_STREAM_RES 4001 ++#define DWC_E_COMMUNICATION 4002 ++#define DWC_E_OVERFLOW 4003 ++#define DWC_E_PROTOCOL 4004 ++#define DWC_E_IN_PROGRESS 4005 ++#define DWC_E_PIPE 4006 ++#define DWC_E_IO 4007 ++#define DWC_E_NO_SPACE 4008 ++ ++#endif ++ ++ ++/** @name Tracing/Logging Functions ++ * ++ * These function provide the capability to add tracing, debugging, and error ++ * messages, as well exceptions as assertions. The WUDEV uses these ++ * extensively. These could be logged to the main console, the serial port, an ++ * internal buffer, etc. These functions could also be no-op if they are too ++ * expensive on your system. By default undefining the DEBUG macro already ++ * no-ops some of these functions. */ ++ ++/** Returns non-zero if in interrupt context. */ ++extern dwc_bool_t DWC_IN_IRQ(void); ++#define dwc_in_irq DWC_IN_IRQ ++ ++/** Returns "IRQ" if DWC_IN_IRQ is true. */ ++static inline char *dwc_irq(void) { ++ return DWC_IN_IRQ() ? "IRQ" : ""; ++} ++ ++/** Returns non-zero if in bottom-half context. */ ++extern dwc_bool_t DWC_IN_BH(void); ++#define dwc_in_bh DWC_IN_BH ++ ++/** Returns "BH" if DWC_IN_BH is true. */ ++static inline char *dwc_bh(void) { ++ return DWC_IN_BH() ? "BH" : ""; ++} ++ ++/** ++ * A vprintf() clone. Just call vprintf if you've got it. ++ */ ++extern void DWC_VPRINTF(char *format, va_list args); ++#define dwc_vprintf DWC_VPRINTF ++ ++/** ++ * A vsnprintf() clone. Just call vprintf if you've got it. ++ */ ++extern int DWC_VSNPRINTF(char *str, int size, char *format, va_list args); ++#define dwc_vsnprintf DWC_VSNPRINTF ++ ++/** ++ * printf() clone. Just call printf if you've go it. ++ */ ++extern void DWC_PRINTF(char *format, ...) ++/* This provides compiler level static checking of the parameters if you're ++ * using GCC. */ ++#ifdef __GNUC__ ++ __attribute__ ((format(printf, 1, 2))); ++#else ++ ; ++#endif ++#define dwc_printf DWC_PRINTF ++ ++/** ++ * sprintf() clone. Just call sprintf if you've got it. ++ */ ++extern int DWC_SPRINTF(char *string, char *format, ...) ++#ifdef __GNUC__ ++ __attribute__ ((format(printf, 2, 3))); ++#else ++ ; ++#endif ++#define dwc_sprintf DWC_SPRINTF ++ ++/** ++ * snprintf() clone. Just call snprintf if you've got it. ++ */ ++extern int DWC_SNPRINTF(char *string, int size, char *format, ...) ++#ifdef __GNUC__ ++ __attribute__ ((format(printf, 3, 4))); ++#else ++ ; ++#endif ++#define dwc_snprintf DWC_SNPRINTF ++ ++/** ++ * Prints a WARNING message. On systems that don't differentiate between ++ * warnings and regular log messages, just print it. Indicates that something ++ * may be wrong with the driver. Works like printf(). ++ * ++ * Use the DWC_WARN macro to call this function. ++ */ ++extern void __DWC_WARN(char *format, ...) ++#ifdef __GNUC__ ++ __attribute__ ((format(printf, 1, 2))); ++#else ++ ; ++#endif ++ ++/** ++ * Prints an error message. On systems that don't differentiate between errors ++ * and regular log messages, just print it. Indicates that something went wrong ++ * with the driver. Works like printf(). ++ * ++ * Use the DWC_ERROR macro to call this function. ++ */ ++extern void __DWC_ERROR(char *format, ...) ++#ifdef __GNUC__ ++ __attribute__ ((format(printf, 1, 2))); ++#else ++ ; ++#endif ++ ++/** ++ * Prints an exception error message and takes some user-defined action such as ++ * print out a backtrace or trigger a breakpoint. Indicates that something went ++ * abnormally wrong with the driver such as programmer error, or other ++ * exceptional condition. It should not be ignored so even on systems without ++ * printing capability, some action should be taken to notify the developer of ++ * it. Works like printf(). ++ */ ++extern void DWC_EXCEPTION(char *format, ...) ++#ifdef __GNUC__ ++ __attribute__ ((format(printf, 1, 2))); ++#else ++ ; ++#endif ++#define dwc_exception DWC_EXCEPTION ++ ++#ifndef DWC_OTG_DEBUG_LEV ++#define DWC_OTG_DEBUG_LEV 0 ++#endif ++ ++#ifdef DEBUG ++/** ++ * Prints out a debug message. Used for logging/trace messages. ++ * ++ * Use the DWC_DEBUG macro to call this function ++ */ ++extern void __DWC_DEBUG(char *format, ...) ++#ifdef __GNUC__ ++ __attribute__ ((format(printf, 1, 2))); ++#else ++ ; ++#endif ++#else ++#define __DWC_DEBUG printk ++#endif ++ ++/** ++ * Prints out a Debug message. ++ */ ++#define DWC_DEBUG(_format, _args...) __DWC_DEBUG("DEBUG:%s:%s: " _format "\n", \ ++ __func__, dwc_irq(), ## _args) ++#define dwc_debug DWC_DEBUG ++/** ++ * Prints out a Debug message if enabled at compile time. ++ */ ++#if DWC_OTG_DEBUG_LEV > 0 ++#define DWC_DEBUGC(_format, _args...) DWC_DEBUG(_format, ##_args ) ++#else ++#define DWC_DEBUGC(_format, _args...) ++#endif ++#define dwc_debugc DWC_DEBUGC ++/** ++ * Prints out an informative message. ++ */ ++#define DWC_INFO(_format, _args...) DWC_PRINTF("INFO:%s: " _format "\n", \ ++ dwc_irq(), ## _args) ++#define dwc_info DWC_INFO ++/** ++ * Prints out an informative message if enabled at compile time. ++ */ ++#if DWC_OTG_DEBUG_LEV > 1 ++#define DWC_INFOC(_format, _args...) DWC_INFO(_format, ##_args ) ++#else ++#define DWC_INFOC(_format, _args...) ++#endif ++#define dwc_infoc DWC_INFOC ++/** ++ * Prints out a warning message. ++ */ ++#define DWC_WARN(_format, _args...) __DWC_WARN("WARN:%s:%s:%d: " _format "\n", \ ++ dwc_irq(), __func__, __LINE__, ## _args) ++#define dwc_warn DWC_WARN ++/** ++ * Prints out an error message. ++ */ ++#define DWC_ERROR(_format, _args...) __DWC_ERROR("ERROR:%s:%s:%d: " _format "\n", \ ++ dwc_irq(), __func__, __LINE__, ## _args) ++#define dwc_error DWC_ERROR ++ ++#define DWC_PROTO_ERROR(_format, _args...) __DWC_WARN("ERROR:%s:%s:%d: " _format "\n", \ ++ dwc_irq(), __func__, __LINE__, ## _args) ++#define dwc_proto_error DWC_PROTO_ERROR ++ ++#ifdef DEBUG ++/** Prints out a exception error message if the _expr expression fails. Disabled ++ * if DEBUG is not enabled. */ ++#define DWC_ASSERT(_expr, _format, _args...) do { \ ++ if (!(_expr)) { DWC_EXCEPTION("%s:%s:%d: " _format "\n", dwc_irq(), \ ++ __FILE__, __LINE__, ## _args); } \ ++ } while (0) ++#else ++#define DWC_ASSERT(_x...) ++#endif ++#define dwc_assert DWC_ASSERT ++ ++ ++/** @name Byte Ordering ++ * The following functions are for conversions between processor's byte ordering ++ * and specific ordering you want. ++ */ ++ ++/** Converts 32 bit data in CPU byte ordering to little endian. */ ++extern uint32_t DWC_CPU_TO_LE32(uint32_t *p); ++#define dwc_cpu_to_le32 DWC_CPU_TO_LE32 ++ ++/** Converts 32 bit data in CPU byte orderint to big endian. */ ++extern uint32_t DWC_CPU_TO_BE32(uint32_t *p); ++#define dwc_cpu_to_be32 DWC_CPU_TO_BE32 ++ ++/** Converts 32 bit little endian data to CPU byte ordering. */ ++extern uint32_t DWC_LE32_TO_CPU(uint32_t *p); ++#define dwc_le32_to_cpu DWC_LE32_TO_CPU ++ ++/** Converts 32 bit big endian data to CPU byte ordering. */ ++extern uint32_t DWC_BE32_TO_CPU(uint32_t *p); ++#define dwc_be32_to_cpu DWC_BE32_TO_CPU ++ ++/** Converts 16 bit data in CPU byte ordering to little endian. */ ++extern uint16_t DWC_CPU_TO_LE16(uint16_t *p); ++#define dwc_cpu_to_le16 DWC_CPU_TO_LE16 ++ ++/** Converts 16 bit data in CPU byte orderint to big endian. */ ++extern uint16_t DWC_CPU_TO_BE16(uint16_t *p); ++#define dwc_cpu_to_be16 DWC_CPU_TO_BE16 ++ ++/** Converts 16 bit little endian data to CPU byte ordering. */ ++extern uint16_t DWC_LE16_TO_CPU(uint16_t *p); ++#define dwc_le16_to_cpu DWC_LE16_TO_CPU ++ ++/** Converts 16 bit bi endian data to CPU byte ordering. */ ++extern uint16_t DWC_BE16_TO_CPU(uint16_t *p); ++#define dwc_be16_to_cpu DWC_BE16_TO_CPU ++ ++ ++/** @name Register Read/Write ++ * ++ * The following six functions should be implemented to read/write registers of ++ * 32-bit and 64-bit sizes. All modules use this to read/write register values. ++ * The reg value is a pointer to the register calculated from the void *base ++ * variable passed into the driver when it is started. */ ++ ++#ifdef DWC_LINUX ++/* Linux doesn't need any extra parameters for register read/write, so we ++ * just throw away the IO context parameter. ++ */ ++/** Reads the content of a 32-bit register. */ ++extern uint32_t DWC_READ_REG32(uint32_t volatile *reg); ++#define dwc_read_reg32(_ctx_,_reg_) DWC_READ_REG32(_reg_) ++ ++/** Reads the content of a 64-bit register. */ ++extern uint64_t DWC_READ_REG64(uint64_t volatile *reg); ++#define dwc_read_reg64(_ctx_,_reg_) DWC_READ_REG64(_reg_) ++ ++/** Writes to a 32-bit register. */ ++extern void DWC_WRITE_REG32(uint32_t volatile *reg, uint32_t value); ++#define dwc_write_reg32(_ctx_,_reg_,_val_) DWC_WRITE_REG32(_reg_, _val_) ++ ++/** Writes to a 64-bit register. */ ++extern void DWC_WRITE_REG64(uint64_t volatile *reg, uint64_t value); ++#define dwc_write_reg64(_ctx_,_reg_,_val_) DWC_WRITE_REG64(_reg_, _val_) ++ ++/** ++ * Modify bit values in a register. Using the ++ * algorithm: (reg_contents & ~clear_mask) | set_mask. ++ */ ++extern void DWC_MODIFY_REG32(uint32_t volatile *reg, uint32_t clear_mask, uint32_t set_mask); ++#define dwc_modify_reg32(_ctx_,_reg_,_cmsk_,_smsk_) DWC_MODIFY_REG32(_reg_,_cmsk_,_smsk_) ++extern void DWC_MODIFY_REG64(uint64_t volatile *reg, uint64_t clear_mask, uint64_t set_mask); ++#define dwc_modify_reg64(_ctx_,_reg_,_cmsk_,_smsk_) DWC_MODIFY_REG64(_reg_,_cmsk_,_smsk_) ++ ++#endif /* DWC_LINUX */ ++ ++#if defined(DWC_FREEBSD) || defined(DWC_NETBSD) ++typedef struct dwc_ioctx { ++ struct device *dev; ++ bus_space_tag_t iot; ++ bus_space_handle_t ioh; ++} dwc_ioctx_t; ++ ++/** BSD needs two extra parameters for register read/write, so we pass ++ * them in using the IO context parameter. ++ */ ++/** Reads the content of a 32-bit register. */ ++extern uint32_t DWC_READ_REG32(void *io_ctx, uint32_t volatile *reg); ++#define dwc_read_reg32 DWC_READ_REG32 ++ ++/** Reads the content of a 64-bit register. */ ++extern uint64_t DWC_READ_REG64(void *io_ctx, uint64_t volatile *reg); ++#define dwc_read_reg64 DWC_READ_REG64 ++ ++/** Writes to a 32-bit register. */ ++extern void DWC_WRITE_REG32(void *io_ctx, uint32_t volatile *reg, uint32_t value); ++#define dwc_write_reg32 DWC_WRITE_REG32 ++ ++/** Writes to a 64-bit register. */ ++extern void DWC_WRITE_REG64(void *io_ctx, uint64_t volatile *reg, uint64_t value); ++#define dwc_write_reg64 DWC_WRITE_REG64 ++ ++/** ++ * Modify bit values in a register. Using the ++ * algorithm: (reg_contents & ~clear_mask) | set_mask. ++ */ ++extern void DWC_MODIFY_REG32(void *io_ctx, uint32_t volatile *reg, uint32_t clear_mask, uint32_t set_mask); ++#define dwc_modify_reg32 DWC_MODIFY_REG32 ++extern void DWC_MODIFY_REG64(void *io_ctx, uint64_t volatile *reg, uint64_t clear_mask, uint64_t set_mask); ++#define dwc_modify_reg64 DWC_MODIFY_REG64 ++ ++#endif /* DWC_FREEBSD || DWC_NETBSD */ ++ ++/** @cond */ ++ ++/** @name Some convenience MACROS used internally. Define DWC_DEBUG_REGS to log the ++ * register writes. */ ++ ++#ifdef DWC_LINUX ++ ++# ifdef DWC_DEBUG_REGS ++ ++#define dwc_define_read_write_reg_n(_reg,_container_type) \ ++static inline uint32_t dwc_read_##_reg##_n(_container_type *container, int num) { \ ++ return DWC_READ_REG32(&container->regs->_reg[num]); \ ++} \ ++static inline void dwc_write_##_reg##_n(_container_type *container, int num, uint32_t data) { \ ++ DWC_DEBUG("WRITING %8s[%d]: %p: %08x", #_reg, num, \ ++ &(((uint32_t*)container->regs->_reg)[num]), data); \ ++ DWC_WRITE_REG32(&(((uint32_t*)container->regs->_reg)[num]), data); \ ++} ++ ++#define dwc_define_read_write_reg(_reg,_container_type) \ ++static inline uint32_t dwc_read_##_reg(_container_type *container) { \ ++ return DWC_READ_REG32(&container->regs->_reg); \ ++} \ ++static inline void dwc_write_##_reg(_container_type *container, uint32_t data) { \ ++ DWC_DEBUG("WRITING %11s: %p: %08x", #_reg, &container->regs->_reg, data); \ ++ DWC_WRITE_REG32(&container->regs->_reg, data); \ ++} ++ ++# else /* DWC_DEBUG_REGS */ ++ ++#define dwc_define_read_write_reg_n(_reg,_container_type) \ ++static inline uint32_t dwc_read_##_reg##_n(_container_type *container, int num) { \ ++ return DWC_READ_REG32(&container->regs->_reg[num]); \ ++} \ ++static inline void dwc_write_##_reg##_n(_container_type *container, int num, uint32_t data) { \ ++ DWC_WRITE_REG32(&(((uint32_t*)container->regs->_reg)[num]), data); \ ++} ++ ++#define dwc_define_read_write_reg(_reg,_container_type) \ ++static inline uint32_t dwc_read_##_reg(_container_type *container) { \ ++ return DWC_READ_REG32(&container->regs->_reg); \ ++} \ ++static inline void dwc_write_##_reg(_container_type *container, uint32_t data) { \ ++ DWC_WRITE_REG32(&container->regs->_reg, data); \ ++} ++ ++# endif /* DWC_DEBUG_REGS */ ++ ++#endif /* DWC_LINUX */ ++ ++#if defined(DWC_FREEBSD) || defined(DWC_NETBSD) ++ ++# ifdef DWC_DEBUG_REGS ++ ++#define dwc_define_read_write_reg_n(_reg,_container_type) \ ++static inline uint32_t dwc_read_##_reg##_n(void *io_ctx, _container_type *container, int num) { \ ++ return DWC_READ_REG32(io_ctx, &container->regs->_reg[num]); \ ++} \ ++static inline void dwc_write_##_reg##_n(void *io_ctx, _container_type *container, int num, uint32_t data) { \ ++ DWC_DEBUG("WRITING %8s[%d]: %p: %08x", #_reg, num, \ ++ &(((uint32_t*)container->regs->_reg)[num]), data); \ ++ DWC_WRITE_REG32(io_ctx, &(((uint32_t*)container->regs->_reg)[num]), data); \ ++} ++ ++#define dwc_define_read_write_reg(_reg,_container_type) \ ++static inline uint32_t dwc_read_##_reg(void *io_ctx, _container_type *container) { \ ++ return DWC_READ_REG32(io_ctx, &container->regs->_reg); \ ++} \ ++static inline void dwc_write_##_reg(void *io_ctx, _container_type *container, uint32_t data) { \ ++ DWC_DEBUG("WRITING %11s: %p: %08x", #_reg, &container->regs->_reg, data); \ ++ DWC_WRITE_REG32(io_ctx, &container->regs->_reg, data); \ ++} ++ ++# else /* DWC_DEBUG_REGS */ ++ ++#define dwc_define_read_write_reg_n(_reg,_container_type) \ ++static inline uint32_t dwc_read_##_reg##_n(void *io_ctx, _container_type *container, int num) { \ ++ return DWC_READ_REG32(io_ctx, &container->regs->_reg[num]); \ ++} \ ++static inline void dwc_write_##_reg##_n(void *io_ctx, _container_type *container, int num, uint32_t data) { \ ++ DWC_WRITE_REG32(io_ctx, &(((uint32_t*)container->regs->_reg)[num]), data); \ ++} ++ ++#define dwc_define_read_write_reg(_reg,_container_type) \ ++static inline uint32_t dwc_read_##_reg(void *io_ctx, _container_type *container) { \ ++ return DWC_READ_REG32(io_ctx, &container->regs->_reg); \ ++} \ ++static inline void dwc_write_##_reg(void *io_ctx, _container_type *container, uint32_t data) { \ ++ DWC_WRITE_REG32(io_ctx, &container->regs->_reg, data); \ ++} ++ ++# endif /* DWC_DEBUG_REGS */ ++ ++#endif /* DWC_FREEBSD || DWC_NETBSD */ ++ ++/** @endcond */ ++ ++ ++#ifdef DWC_CRYPTOLIB ++/** @name Crypto Functions ++ * ++ * These are the low-level cryptographic functions used by the driver. */ ++ ++/** Perform AES CBC */ ++extern int DWC_AES_CBC(uint8_t *message, uint32_t messagelen, uint8_t *key, uint32_t keylen, uint8_t iv[16], uint8_t *out); ++#define dwc_aes_cbc DWC_AES_CBC ++ ++/** Fill the provided buffer with random bytes. These should be cryptographic grade random numbers. */ ++extern void DWC_RANDOM_BYTES(uint8_t *buffer, uint32_t length); ++#define dwc_random_bytes DWC_RANDOM_BYTES ++ ++/** Perform the SHA-256 hash function */ ++extern int DWC_SHA256(uint8_t *message, uint32_t len, uint8_t *out); ++#define dwc_sha256 DWC_SHA256 ++ ++/** Calculated the HMAC-SHA256 */ ++extern int DWC_HMAC_SHA256(uint8_t *message, uint32_t messagelen, uint8_t *key, uint32_t keylen, uint8_t *out); ++#define dwc_hmac_sha256 DWC_HMAC_SHA256 ++ ++#endif /* DWC_CRYPTOLIB */ ++ ++ ++/** @name Memory Allocation ++ * ++ * These function provide access to memory allocation. There are only 2 DMA ++ * functions and 3 Regular memory functions that need to be implemented. None ++ * of the memory debugging routines need to be implemented. The allocation ++ * routines all ZERO the contents of the memory. ++ * ++ * Defining DWC_DEBUG_MEMORY turns on memory debugging and statistic gathering. ++ * This checks for memory leaks, keeping track of alloc/free pairs. It also ++ * keeps track of how much memory the driver is using at any given time. */ ++ ++#define DWC_PAGE_SIZE 4096 ++#define DWC_PAGE_OFFSET(addr) (((uint32_t)addr) & 0xfff) ++#define DWC_PAGE_ALIGNED(addr) ((((uint32_t)addr) & 0xfff) == 0) ++ ++#define DWC_INVALID_DMA_ADDR 0x0 ++ ++#ifdef DWC_LINUX ++/** Type for a DMA address */ ++typedef dma_addr_t dwc_dma_t; ++#endif ++ ++#if defined(DWC_FREEBSD) || defined(DWC_NETBSD) ++typedef bus_addr_t dwc_dma_t; ++#endif ++ ++#ifdef DWC_FREEBSD ++typedef struct dwc_dmactx { ++ struct device *dev; ++ bus_dma_tag_t dma_tag; ++ bus_dmamap_t dma_map; ++ bus_addr_t dma_paddr; ++ void *dma_vaddr; ++} dwc_dmactx_t; ++#endif ++ ++#ifdef DWC_NETBSD ++typedef struct dwc_dmactx { ++ struct device *dev; ++ bus_dma_tag_t dma_tag; ++ bus_dmamap_t dma_map; ++ bus_dma_segment_t segs[1]; ++ int nsegs; ++ bus_addr_t dma_paddr; ++ void *dma_vaddr; ++} dwc_dmactx_t; ++#endif ++ ++/* @todo these functions will be added in the future */ ++#if 0 ++/** ++ * Creates a DMA pool from which you can allocate DMA buffers. Buffers ++ * allocated from this pool will be guaranteed to meet the size, alignment, and ++ * boundary requirements specified. ++ * ++ * @param[in] size Specifies the size of the buffers that will be allocated from ++ * this pool. ++ * @param[in] align Specifies the byte alignment requirements of the buffers ++ * allocated from this pool. Must be a power of 2. ++ * @param[in] boundary Specifies the N-byte boundary that buffers allocated from ++ * this pool must not cross. ++ * ++ * @returns A pointer to an internal opaque structure which is not to be ++ * accessed outside of these library functions. Use this handle to specify ++ * which pools to allocate/free DMA buffers from and also to destroy the pool, ++ * when you are done with it. ++ */ ++extern dwc_pool_t *DWC_DMA_POOL_CREATE(uint32_t size, uint32_t align, uint32_t boundary); ++ ++/** ++ * Destroy a DMA pool. All buffers allocated from that pool must be freed first. ++ */ ++extern void DWC_DMA_POOL_DESTROY(dwc_pool_t *pool); ++ ++/** ++ * Allocate a buffer from the specified DMA pool and zeros its contents. ++ */ ++extern void *DWC_DMA_POOL_ALLOC(dwc_pool_t *pool, uint64_t *dma_addr); ++ ++/** ++ * Free a previously allocated buffer from the DMA pool. ++ */ ++extern void DWC_DMA_POOL_FREE(dwc_pool_t *pool, void *vaddr, void *daddr); ++#endif ++ ++/** Allocates a DMA capable buffer and zeroes its contents. */ ++extern void *__DWC_DMA_ALLOC(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr); ++ ++/** Allocates a DMA capable buffer and zeroes its contents in atomic contest */ ++extern void *__DWC_DMA_ALLOC_ATOMIC(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr); ++ ++/** Frees a previously allocated buffer. */ ++extern void __DWC_DMA_FREE(void *dma_ctx, uint32_t size, void *virt_addr, dwc_dma_t dma_addr); ++ ++/** Allocates a block of memory and zeroes its contents. */ ++extern void *__DWC_ALLOC(void *mem_ctx, uint32_t size); ++ ++/** Allocates a block of memory and zeroes its contents, in an atomic manner ++ * which can be used inside interrupt context. The size should be sufficiently ++ * small, a few KB at most, such that failures are not likely to occur. Can just call ++ * __DWC_ALLOC if it is atomic. */ ++extern void *__DWC_ALLOC_ATOMIC(void *mem_ctx, uint32_t size); ++ ++/** Frees a previously allocated buffer. */ ++extern void __DWC_FREE(void *mem_ctx, void *addr); ++ ++#ifndef DWC_DEBUG_MEMORY ++ ++#define DWC_ALLOC(_size_) __DWC_ALLOC(NULL, _size_) ++#define DWC_ALLOC_ATOMIC(_size_) __DWC_ALLOC_ATOMIC(NULL, _size_) ++#define DWC_FREE(_addr_) __DWC_FREE(NULL, _addr_) ++ ++# ifdef DWC_LINUX ++#define DWC_DMA_ALLOC(_dev, _size_, _dma_) __DWC_DMA_ALLOC(_dev, _size_, _dma_) ++#define DWC_DMA_ALLOC_ATOMIC(_dev, _size_, _dma_) __DWC_DMA_ALLOC_ATOMIC(_dev, _size_, _dma_) ++#define DWC_DMA_FREE(_dev, _size_,_virt_, _dma_) __DWC_DMA_FREE(_dev, _size_, _virt_, _dma_) ++# endif ++ ++# if defined(DWC_FREEBSD) || defined(DWC_NETBSD) ++#define DWC_DMA_ALLOC __DWC_DMA_ALLOC ++#define DWC_DMA_FREE __DWC_DMA_FREE ++# endif ++extern void *dwc_dma_alloc_atomic_debug(uint32_t size, dwc_dma_t *dma_addr, char const *func, int line); ++ ++#else /* DWC_DEBUG_MEMORY */ ++ ++extern void *dwc_alloc_debug(void *mem_ctx, uint32_t size, char const *func, int line); ++extern void *dwc_alloc_atomic_debug(void *mem_ctx, uint32_t size, char const *func, int line); ++extern void dwc_free_debug(void *mem_ctx, void *addr, char const *func, int line); ++extern void *dwc_dma_alloc_debug(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr, ++ char const *func, int line); ++extern void *dwc_dma_alloc_atomic_debug(void *dma_ctx, uint32_t size, dwc_dma_t *dma_addr, ++ char const *func, int line); ++extern void dwc_dma_free_debug(void *dma_ctx, uint32_t size, void *virt_addr, ++ dwc_dma_t dma_addr, char const *func, int line); ++ ++extern int dwc_memory_debug_start(void *mem_ctx); ++extern void dwc_memory_debug_stop(void); ++extern void dwc_memory_debug_report(void); ++ ++#define DWC_ALLOC(_size_) dwc_alloc_debug(NULL, _size_, __func__, __LINE__) ++#define DWC_ALLOC_ATOMIC(_size_) dwc_alloc_atomic_debug(NULL, _size_, \ ++ __func__, __LINE__) ++#define DWC_FREE(_addr_) dwc_free_debug(NULL, _addr_, __func__, __LINE__) ++ ++# ifdef DWC_LINUX ++#define DWC_DMA_ALLOC(_dev, _size_, _dma_) \ ++ dwc_dma_alloc_debug(_dev, _size_, _dma_, __func__, __LINE__) ++#define DWC_DMA_ALLOC_ATOMIC(_dev, _size_, _dma_) \ ++ dwc_dma_alloc_atomic_debug(_dev, _size_, _dma_, __func__, __LINE__) ++#define DWC_DMA_FREE(_dev, _size_, _virt_, _dma_) \ ++ dwc_dma_free_debug(_dev, _size_, _virt_, _dma_, __func__, __LINE__) ++# endif ++ ++# if defined(DWC_FREEBSD) || defined(DWC_NETBSD) ++#define DWC_DMA_ALLOC(_ctx_,_size_,_dma_) dwc_dma_alloc_debug(_ctx_, _size_, \ ++ _dma_, __func__, __LINE__) ++#define DWC_DMA_FREE(_ctx_,_size_,_virt_,_dma_) dwc_dma_free_debug(_ctx_, _size_, \ ++ _virt_, _dma_, __func__, __LINE__) ++# endif ++ ++#endif /* DWC_DEBUG_MEMORY */ ++ ++#define dwc_alloc(_ctx_,_size_) DWC_ALLOC(_size_) ++#define dwc_alloc_atomic(_ctx_,_size_) DWC_ALLOC_ATOMIC(_size_) ++#define dwc_free(_ctx_,_addr_) DWC_FREE(_addr_) ++ ++#ifdef DWC_LINUX ++/* Linux doesn't need any extra parameters for DMA buffer allocation, so we ++ * just throw away the DMA context parameter. ++ */ ++#define dwc_dma_alloc(_ctx_,_size_,_dma_) DWC_DMA_ALLOC(_size_, _dma_) ++#define dwc_dma_alloc_atomic(_ctx_,_size_,_dma_) DWC_DMA_ALLOC_ATOMIC(_size_, _dma_) ++#define dwc_dma_free(_ctx_,_size_,_virt_,_dma_) DWC_DMA_FREE(_size_, _virt_, _dma_) ++#endif ++ ++#if defined(DWC_FREEBSD) || defined(DWC_NETBSD) ++/** BSD needs several extra parameters for DMA buffer allocation, so we pass ++ * them in using the DMA context parameter. ++ */ ++#define dwc_dma_alloc DWC_DMA_ALLOC ++#define dwc_dma_free DWC_DMA_FREE ++#endif ++ ++ ++/** @name Memory and String Processing */ ++ ++/** memset() clone */ ++extern void *DWC_MEMSET(void *dest, uint8_t byte, uint32_t size); ++#define dwc_memset DWC_MEMSET ++ ++/** memcpy() clone */ ++extern void *DWC_MEMCPY(void *dest, void const *src, uint32_t size); ++#define dwc_memcpy DWC_MEMCPY ++ ++/** memmove() clone */ ++extern void *DWC_MEMMOVE(void *dest, void *src, uint32_t size); ++#define dwc_memmove DWC_MEMMOVE ++ ++/** memcmp() clone */ ++extern int DWC_MEMCMP(void *m1, void *m2, uint32_t size); ++#define dwc_memcmp DWC_MEMCMP ++ ++/** strcmp() clone */ ++extern int DWC_STRCMP(void *s1, void *s2); ++#define dwc_strcmp DWC_STRCMP ++ ++/** strncmp() clone */ ++extern int DWC_STRNCMP(void *s1, void *s2, uint32_t size); ++#define dwc_strncmp DWC_STRNCMP ++ ++/** strlen() clone, for NULL terminated ASCII strings */ ++extern int DWC_STRLEN(char const *str); ++#define dwc_strlen DWC_STRLEN ++ ++/** strcpy() clone, for NULL terminated ASCII strings */ ++extern char *DWC_STRCPY(char *to, const char *from); ++#define dwc_strcpy DWC_STRCPY ++ ++/** strdup() clone. If you wish to use memory allocation debugging, this ++ * implementation of strdup should use the DWC_* memory routines instead of ++ * calling a predefined strdup. Otherwise the memory allocated by this routine ++ * will not be seen by the debugging routines. */ ++extern char *DWC_STRDUP(char const *str); ++#define dwc_strdup(_ctx_,_str_) DWC_STRDUP(_str_) ++ ++/** NOT an atoi() clone. Read the description carefully. Returns an integer ++ * converted from the string str in base 10 unless the string begins with a "0x" ++ * in which case it is base 16. String must be a NULL terminated sequence of ++ * ASCII characters and may optionally begin with whitespace, a + or -, and a ++ * "0x" prefix if base 16. The remaining characters must be valid digits for ++ * the number and end with a NULL character. If any invalid characters are ++ * encountered or it returns with a negative error code and the results of the ++ * conversion are undefined. On sucess it returns 0. Overflow conditions are ++ * undefined. An example implementation using atoi() can be referenced from the ++ * Linux implementation. */ ++extern int DWC_ATOI(const char *str, int32_t *value); ++#define dwc_atoi DWC_ATOI ++ ++/** Same as above but for unsigned. */ ++extern int DWC_ATOUI(const char *str, uint32_t *value); ++#define dwc_atoui DWC_ATOUI ++ ++#ifdef DWC_UTFLIB ++/** This routine returns a UTF16LE unicode encoded string from a UTF8 string. */ ++extern int DWC_UTF8_TO_UTF16LE(uint8_t const *utf8string, uint16_t *utf16string, unsigned len); ++#define dwc_utf8_to_utf16le DWC_UTF8_TO_UTF16LE ++#endif ++ ++ ++/** @name Wait queues ++ * ++ * Wait queues provide a means of synchronizing between threads or processes. A ++ * process can block on a waitq if some condition is not true, waiting for it to ++ * become true. When the waitq is triggered all waiting process will get ++ * unblocked and the condition will be check again. Waitqs should be triggered ++ * every time a condition can potentially change.*/ ++struct dwc_waitq; ++ ++/** Type for a waitq */ ++typedef struct dwc_waitq dwc_waitq_t; ++ ++/** The type of waitq condition callback function. This is called every time ++ * condition is evaluated. */ ++typedef int (*dwc_waitq_condition_t)(void *data); ++ ++/** Allocate a waitq */ ++extern dwc_waitq_t *DWC_WAITQ_ALLOC(void); ++#define dwc_waitq_alloc(_ctx_) DWC_WAITQ_ALLOC() ++ ++/** Free a waitq */ ++extern void DWC_WAITQ_FREE(dwc_waitq_t *wq); ++#define dwc_waitq_free DWC_WAITQ_FREE ++ ++/** Check the condition and if it is false, block on the waitq. When unblocked, check the ++ * condition again. The function returns when the condition becomes true. The return value ++ * is 0 on condition true, DWC_WAITQ_ABORTED on abort or killed, or DWC_WAITQ_UNKNOWN on error. */ ++extern int32_t DWC_WAITQ_WAIT(dwc_waitq_t *wq, dwc_waitq_condition_t cond, void *data); ++#define dwc_waitq_wait DWC_WAITQ_WAIT ++ ++/** Check the condition and if it is false, block on the waitq. When unblocked, ++ * check the condition again. The function returns when the condition become ++ * true or the timeout has passed. The return value is 0 on condition true or ++ * DWC_TIMED_OUT on timeout, or DWC_WAITQ_ABORTED, or DWC_WAITQ_UNKNOWN on ++ * error. */ ++extern int32_t DWC_WAITQ_WAIT_TIMEOUT(dwc_waitq_t *wq, dwc_waitq_condition_t cond, ++ void *data, int32_t msecs); ++#define dwc_waitq_wait_timeout DWC_WAITQ_WAIT_TIMEOUT ++ ++/** Trigger a waitq, unblocking all processes. This should be called whenever a condition ++ * has potentially changed. */ ++extern void DWC_WAITQ_TRIGGER(dwc_waitq_t *wq); ++#define dwc_waitq_trigger DWC_WAITQ_TRIGGER ++ ++/** Unblock all processes waiting on the waitq with an ABORTED result. */ ++extern void DWC_WAITQ_ABORT(dwc_waitq_t *wq); ++#define dwc_waitq_abort DWC_WAITQ_ABORT ++ ++ ++/** @name Threads ++ * ++ * A thread must be explicitly stopped. It must check DWC_THREAD_SHOULD_STOP ++ * whenever it is woken up, and then return. The DWC_THREAD_STOP function ++ * returns the value from the thread. ++ */ ++ ++struct dwc_thread; ++ ++/** Type for a thread */ ++typedef struct dwc_thread dwc_thread_t; ++ ++/** The thread function */ ++typedef int (*dwc_thread_function_t)(void *data); ++ ++/** Create a thread and start it running the thread_function. Returns a handle ++ * to the thread */ ++extern dwc_thread_t *DWC_THREAD_RUN(dwc_thread_function_t func, char *name, void *data); ++#define dwc_thread_run(_ctx_,_func_,_name_,_data_) DWC_THREAD_RUN(_func_, _name_, _data_) ++ ++/** Stops a thread. Return the value returned by the thread. Or will return ++ * DWC_ABORT if the thread never started. */ ++extern int DWC_THREAD_STOP(dwc_thread_t *thread); ++#define dwc_thread_stop DWC_THREAD_STOP ++ ++/** Signifies to the thread that it must stop. */ ++#ifdef DWC_LINUX ++/* Linux doesn't need any parameters for kthread_should_stop() */ ++extern dwc_bool_t DWC_THREAD_SHOULD_STOP(void); ++#define dwc_thread_should_stop(_thrd_) DWC_THREAD_SHOULD_STOP() ++ ++/* No thread_exit function in Linux */ ++#define dwc_thread_exit(_thrd_) ++#endif ++ ++#if defined(DWC_FREEBSD) || defined(DWC_NETBSD) ++/** BSD needs the thread pointer for kthread_suspend_check() */ ++extern dwc_bool_t DWC_THREAD_SHOULD_STOP(dwc_thread_t *thread); ++#define dwc_thread_should_stop DWC_THREAD_SHOULD_STOP ++ ++/** The thread must call this to exit. */ ++extern void DWC_THREAD_EXIT(dwc_thread_t *thread); ++#define dwc_thread_exit DWC_THREAD_EXIT ++#endif ++ ++ ++/** @name Work queues ++ * ++ * Workqs are used to queue a callback function to be called at some later time, ++ * in another thread. */ ++struct dwc_workq; ++ ++/** Type for a workq */ ++typedef struct dwc_workq dwc_workq_t; ++ ++/** The type of the callback function to be called. */ ++typedef void (*dwc_work_callback_t)(void *data); ++ ++/** Allocate a workq */ ++extern dwc_workq_t *DWC_WORKQ_ALLOC(char *name); ++#define dwc_workq_alloc(_ctx_,_name_) DWC_WORKQ_ALLOC(_name_) ++ ++/** Free a workq. All work must be completed before being freed. */ ++extern void DWC_WORKQ_FREE(dwc_workq_t *workq); ++#define dwc_workq_free DWC_WORKQ_FREE ++ ++/** Schedule a callback on the workq, passing in data. The function will be ++ * scheduled at some later time. */ ++extern void DWC_WORKQ_SCHEDULE(dwc_workq_t *workq, dwc_work_callback_t cb, ++ void *data, char *format, ...) ++#ifdef __GNUC__ ++ __attribute__ ((format(printf, 4, 5))); ++#else ++ ; ++#endif ++#define dwc_workq_schedule DWC_WORKQ_SCHEDULE ++ ++/** Schedule a callback on the workq, that will be called until at least ++ * given number miliseconds have passed. */ ++extern void DWC_WORKQ_SCHEDULE_DELAYED(dwc_workq_t *workq, dwc_work_callback_t cb, ++ void *data, uint32_t time, char *format, ...) ++#ifdef __GNUC__ ++ __attribute__ ((format(printf, 5, 6))); ++#else ++ ; ++#endif ++#define dwc_workq_schedule_delayed DWC_WORKQ_SCHEDULE_DELAYED ++ ++/** The number of processes in the workq */ ++extern int DWC_WORKQ_PENDING(dwc_workq_t *workq); ++#define dwc_workq_pending DWC_WORKQ_PENDING ++ ++/** Blocks until all the work in the workq is complete or timed out. Returns < ++ * 0 on timeout. */ ++extern int DWC_WORKQ_WAIT_WORK_DONE(dwc_workq_t *workq, int timeout); ++#define dwc_workq_wait_work_done DWC_WORKQ_WAIT_WORK_DONE ++ ++ ++/** @name Tasklets ++ * ++ */ ++struct dwc_tasklet; ++ ++/** Type for a tasklet */ ++typedef struct dwc_tasklet dwc_tasklet_t; ++ ++/** The type of the callback function to be called */ ++typedef void (*dwc_tasklet_callback_t)(void *data); ++ ++/** Allocates a tasklet */ ++extern dwc_tasklet_t *DWC_TASK_ALLOC(char *name, dwc_tasklet_callback_t cb, void *data); ++#define dwc_task_alloc(_ctx_,_name_,_cb_,_data_) DWC_TASK_ALLOC(_name_, _cb_, _data_) ++ ++/** Frees a tasklet */ ++extern void DWC_TASK_FREE(dwc_tasklet_t *task); ++#define dwc_task_free DWC_TASK_FREE ++ ++/** Schedules a tasklet to run */ ++extern void DWC_TASK_SCHEDULE(dwc_tasklet_t *task); ++#define dwc_task_schedule DWC_TASK_SCHEDULE ++ ++extern void DWC_TASK_HI_SCHEDULE(dwc_tasklet_t *task); ++#define dwc_task_hi_schedule DWC_TASK_HI_SCHEDULE ++ ++/** @name Timer ++ * ++ * Callbacks must be small and atomic. ++ */ ++struct dwc_timer; ++ ++/** Type for a timer */ ++typedef struct dwc_timer dwc_timer_t; ++ ++/** The type of the callback function to be called */ ++typedef void (*dwc_timer_callback_t)(void *data); ++ ++/** Allocates a timer */ ++extern dwc_timer_t *DWC_TIMER_ALLOC(char *name, dwc_timer_callback_t cb, void *data); ++#define dwc_timer_alloc(_ctx_,_name_,_cb_,_data_) DWC_TIMER_ALLOC(_name_,_cb_,_data_) ++ ++/** Frees a timer */ ++extern void DWC_TIMER_FREE(dwc_timer_t *timer); ++#define dwc_timer_free DWC_TIMER_FREE ++ ++/** Schedules the timer to run at time ms from now. And will repeat at every ++ * repeat_interval msec therafter ++ * ++ * Modifies a timer that is still awaiting execution to a new expiration time. ++ * The mod_time is added to the old time. */ ++extern void DWC_TIMER_SCHEDULE(dwc_timer_t *timer, uint32_t time); ++#define dwc_timer_schedule DWC_TIMER_SCHEDULE ++ ++/** Disables the timer from execution. */ ++extern void DWC_TIMER_CANCEL(dwc_timer_t *timer); ++#define dwc_timer_cancel DWC_TIMER_CANCEL ++ ++ ++/** @name Spinlocks ++ * ++ * These locks are used when the work between the lock/unlock is atomic and ++ * short. Interrupts are also disabled during the lock/unlock and thus they are ++ * suitable to lock between interrupt/non-interrupt context. They also lock ++ * between processes if you have multiple CPUs or Preemption. If you don't have ++ * multiple CPUS or Preemption, then the you can simply implement the ++ * DWC_SPINLOCK and DWC_SPINUNLOCK to disable and enable interrupts. Because ++ * the work between the lock/unlock is atomic, the process context will never ++ * change, and so you never have to lock between processes. */ ++ ++struct dwc_spinlock; ++ ++/** Type for a spinlock */ ++typedef struct dwc_spinlock dwc_spinlock_t; ++ ++/** Type for the 'flags' argument to spinlock funtions */ ++typedef unsigned long dwc_irqflags_t; ++ ++/** Returns an initialized lock variable. This function should allocate and ++ * initialize the OS-specific data structure used for locking. This data ++ * structure is to be used for the DWC_LOCK and DWC_UNLOCK functions and should ++ * be freed by the DWC_FREE_LOCK when it is no longer used. ++ * ++ * For Linux Spinlock Debugging make it macro because the debugging routines use ++ * the symbol name to determine recursive locking. Using a wrapper function ++ * makes it falsely think recursive locking occurs. */ ++#if defined(DWC_LINUX) && defined(CONFIG_DEBUG_SPINLOCK) ++#define DWC_SPINLOCK_ALLOC_LINUX_DEBUG(lock) ({ \ ++ lock = DWC_ALLOC(sizeof(spinlock_t)); \ ++ if (lock) { \ ++ spin_lock_init((spinlock_t *)lock); \ ++ } \ ++}) ++#else ++extern dwc_spinlock_t *DWC_SPINLOCK_ALLOC(void); ++#define dwc_spinlock_alloc(_ctx_) DWC_SPINLOCK_ALLOC() ++#endif ++ ++/** Frees an initialized lock variable. */ ++extern void DWC_SPINLOCK_FREE(dwc_spinlock_t *lock); ++#define dwc_spinlock_free(_ctx_,_lock_) DWC_SPINLOCK_FREE(_lock_) ++ ++/** Disables interrupts and blocks until it acquires the lock. ++ * ++ * @param lock Pointer to the spinlock. ++ * @param flags Unsigned long for irq flags storage. ++ */ ++extern void DWC_SPINLOCK_IRQSAVE(dwc_spinlock_t *lock, dwc_irqflags_t *flags); ++#define dwc_spinlock_irqsave DWC_SPINLOCK_IRQSAVE ++ ++/** Re-enables the interrupt and releases the lock. ++ * ++ * @param lock Pointer to the spinlock. ++ * @param flags Unsigned long for irq flags storage. Must be the same as was ++ * passed into DWC_LOCK. ++ */ ++extern void DWC_SPINUNLOCK_IRQRESTORE(dwc_spinlock_t *lock, dwc_irqflags_t flags); ++#define dwc_spinunlock_irqrestore DWC_SPINUNLOCK_IRQRESTORE ++ ++/** Blocks until it acquires the lock. ++ * ++ * @param lock Pointer to the spinlock. ++ */ ++extern void DWC_SPINLOCK(dwc_spinlock_t *lock); ++#define dwc_spinlock DWC_SPINLOCK ++ ++/** Releases the lock. ++ * ++ * @param lock Pointer to the spinlock. ++ */ ++extern void DWC_SPINUNLOCK(dwc_spinlock_t *lock); ++#define dwc_spinunlock DWC_SPINUNLOCK ++ ++ ++/** @name Mutexes ++ * ++ * Unlike spinlocks Mutexes lock only between processes and the work between the ++ * lock/unlock CAN block, therefore it CANNOT be called from interrupt context. ++ */ ++ ++struct dwc_mutex; ++ ++/** Type for a mutex */ ++typedef struct dwc_mutex dwc_mutex_t; ++ ++/* For Linux Mutex Debugging make it inline because the debugging routines use ++ * the symbol to determine recursive locking. This makes it falsely think ++ * recursive locking occurs. */ ++#if defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES) ++#define DWC_MUTEX_ALLOC_LINUX_DEBUG(__mutexp) ({ \ ++ __mutexp = (dwc_mutex_t *)DWC_ALLOC(sizeof(struct mutex)); \ ++ mutex_init((struct mutex *)__mutexp); \ ++}) ++#endif ++ ++/** Allocate a mutex */ ++extern dwc_mutex_t *DWC_MUTEX_ALLOC(void); ++#define dwc_mutex_alloc(_ctx_) DWC_MUTEX_ALLOC() ++ ++/* For memory leak debugging when using Linux Mutex Debugging */ ++#if defined(DWC_LINUX) && defined(CONFIG_DEBUG_MUTEXES) ++#define DWC_MUTEX_FREE(__mutexp) do { \ ++ mutex_destroy((struct mutex *)__mutexp); \ ++ DWC_FREE(__mutexp); \ ++} while(0) ++#else ++/** Free a mutex */ ++extern void DWC_MUTEX_FREE(dwc_mutex_t *mutex); ++#define dwc_mutex_free(_ctx_,_mutex_) DWC_MUTEX_FREE(_mutex_) ++#endif ++ ++/** Lock a mutex */ ++extern void DWC_MUTEX_LOCK(dwc_mutex_t *mutex); ++#define dwc_mutex_lock DWC_MUTEX_LOCK ++ ++/** Non-blocking lock returns 1 on successful lock. */ ++extern int DWC_MUTEX_TRYLOCK(dwc_mutex_t *mutex); ++#define dwc_mutex_trylock DWC_MUTEX_TRYLOCK ++ ++/** Unlock a mutex */ ++extern void DWC_MUTEX_UNLOCK(dwc_mutex_t *mutex); ++#define dwc_mutex_unlock DWC_MUTEX_UNLOCK ++ ++ ++/** @name Time */ ++ ++/** Microsecond delay. ++ * ++ * @param usecs Microseconds to delay. ++ */ ++extern void DWC_UDELAY(uint32_t usecs); ++#define dwc_udelay DWC_UDELAY ++ ++/** Millisecond delay. ++ * ++ * @param msecs Milliseconds to delay. ++ */ ++extern void DWC_MDELAY(uint32_t msecs); ++#define dwc_mdelay DWC_MDELAY ++ ++/** Non-busy waiting. ++ * Sleeps for specified number of milliseconds. ++ * ++ * @param msecs Milliseconds to sleep. ++ */ ++extern void DWC_MSLEEP(uint32_t msecs); ++#define dwc_msleep DWC_MSLEEP ++ ++/** ++ * Returns number of milliseconds since boot. ++ */ ++extern uint32_t DWC_TIME(void); ++#define dwc_time DWC_TIME ++ ++ ++ ++ ++/* @mainpage DWC Portability and Common Library ++ * ++ * This is the documentation for the DWC Portability and Common Library. ++ * ++ * @section intro Introduction ++ * ++ * The DWC Portability library consists of wrapper calls and data structures to ++ * all low-level functions which are typically provided by the OS. The WUDEV ++ * driver uses only these functions. In order to port the WUDEV driver, only ++ * the functions in this library need to be re-implemented, with the same ++ * behavior as documented here. ++ * ++ * The Common library consists of higher level functions, which rely only on ++ * calling the functions from the DWC Portability library. These common ++ * routines are shared across modules. Some of the common libraries need to be ++ * used directly by the driver programmer when porting WUDEV. Such as the ++ * parameter and notification libraries. ++ * ++ * @section low Portability Library OS Wrapper Functions ++ * ++ * Any function starting with DWC and in all CAPS is a low-level OS-wrapper that ++ * needs to be implemented when porting, for example DWC_MUTEX_ALLOC(). All of ++ * these functions are included in the dwc_os.h file. ++ * ++ * There are many functions here covering a wide array of OS services. Please ++ * see dwc_os.h for details, and implementation notes for each function. ++ * ++ * @section common Common Library Functions ++ * ++ * Any function starting with dwc and in all lowercase is a common library ++ * routine. These functions have a portable implementation and do not need to ++ * be reimplemented when porting. The common routines can be used by any ++ * driver, and some must be used by the end user to control the drivers. For ++ * example, you must use the Parameter common library in order to set the ++ * parameters in the WUDEV module. ++ * ++ * The common libraries consist of the following: ++ * ++ * - Connection Contexts - Used internally and can be used by end-user. See dwc_cc.h ++ * - Parameters - Used internally and can be used by end-user. See dwc_params.h ++ * - Notifications - Used internally and can be used by end-user. See dwc_notifier.h ++ * - Lists - Used internally and can be used by end-user. See dwc_list.h ++ * - Memory Debugging - Used internally and can be used by end-user. See dwc_os.h ++ * - Modpow - Used internally only. See dwc_modpow.h ++ * - DH - Used internally only. See dwc_dh.h ++ * - Crypto - Used internally only. See dwc_crypto.h ++ * ++ * ++ * @section prereq Prerequistes For dwc_os.h ++ * @subsection types Data Types ++ * ++ * The dwc_os.h file assumes that several low-level data types are pre defined for the ++ * compilation environment. These data types are: ++ * ++ * - uint8_t - unsigned 8-bit data type ++ * - int8_t - signed 8-bit data type ++ * - uint16_t - unsigned 16-bit data type ++ * - int16_t - signed 16-bit data type ++ * - uint32_t - unsigned 32-bit data type ++ * - int32_t - signed 32-bit data type ++ * - uint64_t - unsigned 64-bit data type ++ * - int64_t - signed 64-bit data type ++ * ++ * Ensure that these are defined before using dwc_os.h. The easiest way to do ++ * that is to modify the top of the file to include the appropriate header. ++ * This is already done for the Linux environment. If the DWC_LINUX macro is ++ * defined, the correct header will be added. A standard header is ++ * also used for environments where standard C headers are available. ++ * ++ * @subsection stdarg Variable Arguments ++ * ++ * Variable arguments are provided by a standard C header . it is ++ * available in Both the Linux and ANSI C enviornment. An equivalent must be ++ * provided in your enviornment in order to use dwc_os.h with the debug and ++ * tracing message functionality. ++ * ++ * @subsection thread Threading ++ * ++ * WUDEV Core must be run on an operating system that provides for multiple ++ * threads/processes. Threading can be implemented in many ways, even in ++ * embedded systems without an operating system. At the bare minimum, the ++ * system should be able to start any number of processes at any time to handle ++ * special work. It need not be a pre-emptive system. Process context can ++ * change upon a call to a blocking function. The hardware interrupt context ++ * that calls the module's ISR() function must be differentiable from process ++ * context, even if your processes are impemented via a hardware interrupt. ++ * Further locking mechanism between process must exist (or be implemented), and ++ * process context must have a way to disable interrupts for a period of time to ++ * lock them out. If all of this exists, the functions in dwc_os.h related to ++ * threading should be able to be implemented with the defined behavior. ++ * ++ */ ++ ++#ifdef __cplusplus ++} ++#endif ++ ++#endif /* _DWC_OS_H_ */ +--- /dev/null ++++ b/drivers/usb/host/dwc_common_port/usb.h +@@ -0,0 +1,946 @@ ++/* ++ * Copyright (c) 1998 The NetBSD Foundation, Inc. ++ * All rights reserved. ++ * ++ * This code is derived from software contributed to The NetBSD Foundation ++ * by Lennart Augustsson (lennart@augustsson.net) at ++ * Carlstedt Research & Technology. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions ++ * are met: ++ * 1. Redistributions of source code must retain the above copyright ++ * notice, this list of conditions and the following disclaimer. ++ * 2. Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in the ++ * documentation and/or other materials provided with the distribution. ++ * 3. All advertising materials mentioning features or use of this software ++ * must display the following acknowledgement: ++ * This product includes software developed by the NetBSD ++ * Foundation, Inc. and its contributors. ++ * 4. Neither the name of The NetBSD Foundation nor the names of its ++ * contributors may be used to endorse or promote products derived ++ * from this software without specific prior written permission. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS ++ * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED ++ * TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR ++ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS ++ * BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR ++ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF ++ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS ++ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN ++ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ++ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE ++ * POSSIBILITY OF SUCH DAMAGE. ++ */ ++ ++/* Modified by Synopsys, Inc, 12/12/2007 */ ++ ++ ++#ifndef _USB_H_ ++#define _USB_H_ ++ ++#ifdef __cplusplus ++extern "C" { ++#endif ++ ++/* ++ * The USB records contain some unaligned little-endian word ++ * components. The U[SG]ETW macros take care of both the alignment ++ * and endian problem and should always be used to access non-byte ++ * values. ++ */ ++typedef u_int8_t uByte; ++typedef u_int8_t uWord[2]; ++typedef u_int8_t uDWord[4]; ++ ++#define USETW2(w,h,l) ((w)[0] = (u_int8_t)(l), (w)[1] = (u_int8_t)(h)) ++#define UCONSTW(x) { (x) & 0xff, ((x) >> 8) & 0xff } ++#define UCONSTDW(x) { (x) & 0xff, ((x) >> 8) & 0xff, \ ++ ((x) >> 16) & 0xff, ((x) >> 24) & 0xff } ++ ++#if 1 ++#define UGETW(w) ((w)[0] | ((w)[1] << 8)) ++#define USETW(w,v) ((w)[0] = (u_int8_t)(v), (w)[1] = (u_int8_t)((v) >> 8)) ++#define UGETDW(w) ((w)[0] | ((w)[1] << 8) | ((w)[2] << 16) | ((w)[3] << 24)) ++#define USETDW(w,v) ((w)[0] = (u_int8_t)(v), \ ++ (w)[1] = (u_int8_t)((v) >> 8), \ ++ (w)[2] = (u_int8_t)((v) >> 16), \ ++ (w)[3] = (u_int8_t)((v) >> 24)) ++#else ++/* ++ * On little-endian machines that can handle unanliged accesses ++ * (e.g. i386) these macros can be replaced by the following. ++ */ ++#define UGETW(w) (*(u_int16_t *)(w)) ++#define USETW(w,v) (*(u_int16_t *)(w) = (v)) ++#define UGETDW(w) (*(u_int32_t *)(w)) ++#define USETDW(w,v) (*(u_int32_t *)(w) = (v)) ++#endif ++ ++/* ++ * Macros for accessing UAS IU fields, which are big-endian ++ */ ++#define IUSETW2(w,h,l) ((w)[0] = (u_int8_t)(h), (w)[1] = (u_int8_t)(l)) ++#define IUCONSTW(x) { ((x) >> 8) & 0xff, (x) & 0xff } ++#define IUCONSTDW(x) { ((x) >> 24) & 0xff, ((x) >> 16) & 0xff, \ ++ ((x) >> 8) & 0xff, (x) & 0xff } ++#define IUGETW(w) (((w)[0] << 8) | (w)[1]) ++#define IUSETW(w,v) ((w)[0] = (u_int8_t)((v) >> 8), (w)[1] = (u_int8_t)(v)) ++#define IUGETDW(w) (((w)[0] << 24) | ((w)[1] << 16) | ((w)[2] << 8) | (w)[3]) ++#define IUSETDW(w,v) ((w)[0] = (u_int8_t)((v) >> 24), \ ++ (w)[1] = (u_int8_t)((v) >> 16), \ ++ (w)[2] = (u_int8_t)((v) >> 8), \ ++ (w)[3] = (u_int8_t)(v)) ++ ++#define UPACKED __attribute__((__packed__)) ++ ++typedef struct { ++ uByte bmRequestType; ++ uByte bRequest; ++ uWord wValue; ++ uWord wIndex; ++ uWord wLength; ++} UPACKED usb_device_request_t; ++ ++#define UT_GET_DIR(a) ((a) & 0x80) ++#define UT_WRITE 0x00 ++#define UT_READ 0x80 ++ ++#define UT_GET_TYPE(a) ((a) & 0x60) ++#define UT_STANDARD 0x00 ++#define UT_CLASS 0x20 ++#define UT_VENDOR 0x40 ++ ++#define UT_GET_RECIPIENT(a) ((a) & 0x1f) ++#define UT_DEVICE 0x00 ++#define UT_INTERFACE 0x01 ++#define UT_ENDPOINT 0x02 ++#define UT_OTHER 0x03 ++ ++#define UT_READ_DEVICE (UT_READ | UT_STANDARD | UT_DEVICE) ++#define UT_READ_INTERFACE (UT_READ | UT_STANDARD | UT_INTERFACE) ++#define UT_READ_ENDPOINT (UT_READ | UT_STANDARD | UT_ENDPOINT) ++#define UT_WRITE_DEVICE (UT_WRITE | UT_STANDARD | UT_DEVICE) ++#define UT_WRITE_INTERFACE (UT_WRITE | UT_STANDARD | UT_INTERFACE) ++#define UT_WRITE_ENDPOINT (UT_WRITE | UT_STANDARD | UT_ENDPOINT) ++#define UT_READ_CLASS_DEVICE (UT_READ | UT_CLASS | UT_DEVICE) ++#define UT_READ_CLASS_INTERFACE (UT_READ | UT_CLASS | UT_INTERFACE) ++#define UT_READ_CLASS_OTHER (UT_READ | UT_CLASS | UT_OTHER) ++#define UT_READ_CLASS_ENDPOINT (UT_READ | UT_CLASS | UT_ENDPOINT) ++#define UT_WRITE_CLASS_DEVICE (UT_WRITE | UT_CLASS | UT_DEVICE) ++#define UT_WRITE_CLASS_INTERFACE (UT_WRITE | UT_CLASS | UT_INTERFACE) ++#define UT_WRITE_CLASS_OTHER (UT_WRITE | UT_CLASS | UT_OTHER) ++#define UT_WRITE_CLASS_ENDPOINT (UT_WRITE | UT_CLASS | UT_ENDPOINT) ++#define UT_READ_VENDOR_DEVICE (UT_READ | UT_VENDOR | UT_DEVICE) ++#define UT_READ_VENDOR_INTERFACE (UT_READ | UT_VENDOR | UT_INTERFACE) ++#define UT_READ_VENDOR_OTHER (UT_READ | UT_VENDOR | UT_OTHER) ++#define UT_READ_VENDOR_ENDPOINT (UT_READ | UT_VENDOR | UT_ENDPOINT) ++#define UT_WRITE_VENDOR_DEVICE (UT_WRITE | UT_VENDOR | UT_DEVICE) ++#define UT_WRITE_VENDOR_INTERFACE (UT_WRITE | UT_VENDOR | UT_INTERFACE) ++#define UT_WRITE_VENDOR_OTHER (UT_WRITE | UT_VENDOR | UT_OTHER) ++#define UT_WRITE_VENDOR_ENDPOINT (UT_WRITE | UT_VENDOR | UT_ENDPOINT) ++ ++/* Requests */ ++#define UR_GET_STATUS 0x00 ++#define USTAT_STANDARD_STATUS 0x00 ++#define WUSTAT_WUSB_FEATURE 0x01 ++#define WUSTAT_CHANNEL_INFO 0x02 ++#define WUSTAT_RECEIVED_DATA 0x03 ++#define WUSTAT_MAS_AVAILABILITY 0x04 ++#define WUSTAT_CURRENT_TRANSMIT_POWER 0x05 ++#define UR_CLEAR_FEATURE 0x01 ++#define UR_SET_FEATURE 0x03 ++#define UR_SET_AND_TEST_FEATURE 0x0c ++#define UR_SET_ADDRESS 0x05 ++#define UR_GET_DESCRIPTOR 0x06 ++#define UDESC_DEVICE 0x01 ++#define UDESC_CONFIG 0x02 ++#define UDESC_STRING 0x03 ++#define UDESC_INTERFACE 0x04 ++#define UDESC_ENDPOINT 0x05 ++#define UDESC_SS_USB_COMPANION 0x30 ++#define UDESC_DEVICE_QUALIFIER 0x06 ++#define UDESC_OTHER_SPEED_CONFIGURATION 0x07 ++#define UDESC_INTERFACE_POWER 0x08 ++#define UDESC_OTG 0x09 ++#define WUDESC_SECURITY 0x0c ++#define WUDESC_KEY 0x0d ++#define WUD_GET_KEY_INDEX(_wValue_) ((_wValue_) & 0xf) ++#define WUD_GET_KEY_TYPE(_wValue_) (((_wValue_) & 0x30) >> 4) ++#define WUD_KEY_TYPE_ASSOC 0x01 ++#define WUD_KEY_TYPE_GTK 0x02 ++#define WUD_GET_KEY_ORIGIN(_wValue_) (((_wValue_) & 0x40) >> 6) ++#define WUD_KEY_ORIGIN_HOST 0x00 ++#define WUD_KEY_ORIGIN_DEVICE 0x01 ++#define WUDESC_ENCRYPTION_TYPE 0x0e ++#define WUDESC_BOS 0x0f ++#define WUDESC_DEVICE_CAPABILITY 0x10 ++#define WUDESC_WIRELESS_ENDPOINT_COMPANION 0x11 ++#define UDESC_BOS 0x0f ++#define UDESC_DEVICE_CAPABILITY 0x10 ++#define UDESC_CS_DEVICE 0x21 /* class specific */ ++#define UDESC_CS_CONFIG 0x22 ++#define UDESC_CS_STRING 0x23 ++#define UDESC_CS_INTERFACE 0x24 ++#define UDESC_CS_ENDPOINT 0x25 ++#define UDESC_HUB 0x29 ++#define UR_SET_DESCRIPTOR 0x07 ++#define UR_GET_CONFIG 0x08 ++#define UR_SET_CONFIG 0x09 ++#define UR_GET_INTERFACE 0x0a ++#define UR_SET_INTERFACE 0x0b ++#define UR_SYNCH_FRAME 0x0c ++#define WUR_SET_ENCRYPTION 0x0d ++#define WUR_GET_ENCRYPTION 0x0e ++#define WUR_SET_HANDSHAKE 0x0f ++#define WUR_GET_HANDSHAKE 0x10 ++#define WUR_SET_CONNECTION 0x11 ++#define WUR_SET_SECURITY_DATA 0x12 ++#define WUR_GET_SECURITY_DATA 0x13 ++#define WUR_SET_WUSB_DATA 0x14 ++#define WUDATA_DRPIE_INFO 0x01 ++#define WUDATA_TRANSMIT_DATA 0x02 ++#define WUDATA_TRANSMIT_PARAMS 0x03 ++#define WUDATA_RECEIVE_PARAMS 0x04 ++#define WUDATA_TRANSMIT_POWER 0x05 ++#define WUR_LOOPBACK_DATA_WRITE 0x15 ++#define WUR_LOOPBACK_DATA_READ 0x16 ++#define WUR_SET_INTERFACE_DS 0x17 ++ ++/* Feature numbers */ ++#define UF_ENDPOINT_HALT 0 ++#define UF_DEVICE_REMOTE_WAKEUP 1 ++#define UF_TEST_MODE 2 ++#define UF_DEVICE_B_HNP_ENABLE 3 ++#define UF_DEVICE_A_HNP_SUPPORT 4 ++#define UF_DEVICE_A_ALT_HNP_SUPPORT 5 ++#define WUF_WUSB 3 ++#define WUF_TX_DRPIE 0x0 ++#define WUF_DEV_XMIT_PACKET 0x1 ++#define WUF_COUNT_PACKETS 0x2 ++#define WUF_CAPTURE_PACKETS 0x3 ++#define UF_FUNCTION_SUSPEND 0 ++#define UF_U1_ENABLE 48 ++#define UF_U2_ENABLE 49 ++#define UF_LTM_ENABLE 50 ++ ++/* Class requests from the USB 2.0 hub spec, table 11-15 */ ++#define UCR_CLEAR_HUB_FEATURE (0x2000 | UR_CLEAR_FEATURE) ++#define UCR_CLEAR_PORT_FEATURE (0x2300 | UR_CLEAR_FEATURE) ++#define UCR_GET_HUB_DESCRIPTOR (0xa000 | UR_GET_DESCRIPTOR) ++#define UCR_GET_HUB_STATUS (0xa000 | UR_GET_STATUS) ++#define UCR_GET_PORT_STATUS (0xa300 | UR_GET_STATUS) ++#define UCR_SET_HUB_FEATURE (0x2000 | UR_SET_FEATURE) ++#define UCR_SET_PORT_FEATURE (0x2300 | UR_SET_FEATURE) ++#define UCR_SET_AND_TEST_PORT_FEATURE (0xa300 | UR_SET_AND_TEST_FEATURE) ++ ++#ifdef _MSC_VER ++#include ++#endif ++ ++typedef struct { ++ uByte bLength; ++ uByte bDescriptorType; ++ uByte bDescriptorSubtype; ++} UPACKED usb_descriptor_t; ++ ++typedef struct { ++ uByte bLength; ++ uByte bDescriptorType; ++} UPACKED usb_descriptor_header_t; ++ ++typedef struct { ++ uByte bLength; ++ uByte bDescriptorType; ++ uWord bcdUSB; ++#define UD_USB_2_0 0x0200 ++#define UD_IS_USB2(d) (UGETW((d)->bcdUSB) >= UD_USB_2_0) ++ uByte bDeviceClass; ++ uByte bDeviceSubClass; ++ uByte bDeviceProtocol; ++ uByte bMaxPacketSize; ++ /* The fields below are not part of the initial descriptor. */ ++ uWord idVendor; ++ uWord idProduct; ++ uWord bcdDevice; ++ uByte iManufacturer; ++ uByte iProduct; ++ uByte iSerialNumber; ++ uByte bNumConfigurations; ++} UPACKED usb_device_descriptor_t; ++#define USB_DEVICE_DESCRIPTOR_SIZE 18 ++ ++typedef struct { ++ uByte bLength; ++ uByte bDescriptorType; ++ uWord wTotalLength; ++ uByte bNumInterface; ++ uByte bConfigurationValue; ++ uByte iConfiguration; ++#define UC_ATT_ONE (1 << 7) /* must be set */ ++#define UC_ATT_SELFPOWER (1 << 6) /* self powered */ ++#define UC_ATT_WAKEUP (1 << 5) /* can wakeup */ ++#define UC_ATT_BATTERY (1 << 4) /* battery powered */ ++ uByte bmAttributes; ++#define UC_BUS_POWERED 0x80 ++#define UC_SELF_POWERED 0x40 ++#define UC_REMOTE_WAKEUP 0x20 ++ uByte bMaxPower; /* max current in 2 mA units */ ++#define UC_POWER_FACTOR 2 ++} UPACKED usb_config_descriptor_t; ++#define USB_CONFIG_DESCRIPTOR_SIZE 9 ++ ++typedef struct { ++ uByte bLength; ++ uByte bDescriptorType; ++ uByte bInterfaceNumber; ++ uByte bAlternateSetting; ++ uByte bNumEndpoints; ++ uByte bInterfaceClass; ++ uByte bInterfaceSubClass; ++ uByte bInterfaceProtocol; ++ uByte iInterface; ++} UPACKED usb_interface_descriptor_t; ++#define USB_INTERFACE_DESCRIPTOR_SIZE 9 ++ ++typedef struct { ++ uByte bLength; ++ uByte bDescriptorType; ++ uByte bEndpointAddress; ++#define UE_GET_DIR(a) ((a) & 0x80) ++#define UE_SET_DIR(a,d) ((a) | (((d)&1) << 7)) ++#define UE_DIR_IN 0x80 ++#define UE_DIR_OUT 0x00 ++#define UE_ADDR 0x0f ++#define UE_GET_ADDR(a) ((a) & UE_ADDR) ++ uByte bmAttributes; ++#define UE_XFERTYPE 0x03 ++#define UE_CONTROL 0x00 ++#define UE_ISOCHRONOUS 0x01 ++#define UE_BULK 0x02 ++#define UE_INTERRUPT 0x03 ++#define UE_GET_XFERTYPE(a) ((a) & UE_XFERTYPE) ++#define UE_ISO_TYPE 0x0c ++#define UE_ISO_ASYNC 0x04 ++#define UE_ISO_ADAPT 0x08 ++#define UE_ISO_SYNC 0x0c ++#define UE_GET_ISO_TYPE(a) ((a) & UE_ISO_TYPE) ++ uWord wMaxPacketSize; ++ uByte bInterval; ++} UPACKED usb_endpoint_descriptor_t; ++#define USB_ENDPOINT_DESCRIPTOR_SIZE 7 ++ ++typedef struct ss_endpoint_companion_descriptor { ++ uByte bLength; ++ uByte bDescriptorType; ++ uByte bMaxBurst; ++#define USSE_GET_MAX_STREAMS(a) ((a) & 0x1f) ++#define USSE_SET_MAX_STREAMS(a, b) ((a) | ((b) & 0x1f)) ++#define USSE_GET_MAX_PACKET_NUM(a) ((a) & 0x03) ++#define USSE_SET_MAX_PACKET_NUM(a, b) ((a) | ((b) & 0x03)) ++ uByte bmAttributes; ++ uWord wBytesPerInterval; ++} UPACKED ss_endpoint_companion_descriptor_t; ++#define USB_SS_ENDPOINT_COMPANION_DESCRIPTOR_SIZE 6 ++ ++typedef struct { ++ uByte bLength; ++ uByte bDescriptorType; ++ uWord bString[127]; ++} UPACKED usb_string_descriptor_t; ++#define USB_MAX_STRING_LEN 128 ++#define USB_LANGUAGE_TABLE 0 /* # of the string language id table */ ++ ++/* Hub specific request */ ++#define UR_GET_BUS_STATE 0x02 ++#define UR_CLEAR_TT_BUFFER 0x08 ++#define UR_RESET_TT 0x09 ++#define UR_GET_TT_STATE 0x0a ++#define UR_STOP_TT 0x0b ++ ++/* Hub features */ ++#define UHF_C_HUB_LOCAL_POWER 0 ++#define UHF_C_HUB_OVER_CURRENT 1 ++#define UHF_PORT_CONNECTION 0 ++#define UHF_PORT_ENABLE 1 ++#define UHF_PORT_SUSPEND 2 ++#define UHF_PORT_OVER_CURRENT 3 ++#define UHF_PORT_RESET 4 ++#define UHF_PORT_L1 5 ++#define UHF_PORT_POWER 8 ++#define UHF_PORT_LOW_SPEED 9 ++#define UHF_PORT_HIGH_SPEED 10 ++#define UHF_C_PORT_CONNECTION 16 ++#define UHF_C_PORT_ENABLE 17 ++#define UHF_C_PORT_SUSPEND 18 ++#define UHF_C_PORT_OVER_CURRENT 19 ++#define UHF_C_PORT_RESET 20 ++#define UHF_C_PORT_L1 23 ++#define UHF_PORT_TEST 21 ++#define UHF_PORT_INDICATOR 22 ++ ++typedef struct { ++ uByte bDescLength; ++ uByte bDescriptorType; ++ uByte bNbrPorts; ++ uWord wHubCharacteristics; ++#define UHD_PWR 0x0003 ++#define UHD_PWR_GANGED 0x0000 ++#define UHD_PWR_INDIVIDUAL 0x0001 ++#define UHD_PWR_NO_SWITCH 0x0002 ++#define UHD_COMPOUND 0x0004 ++#define UHD_OC 0x0018 ++#define UHD_OC_GLOBAL 0x0000 ++#define UHD_OC_INDIVIDUAL 0x0008 ++#define UHD_OC_NONE 0x0010 ++#define UHD_TT_THINK 0x0060 ++#define UHD_TT_THINK_8 0x0000 ++#define UHD_TT_THINK_16 0x0020 ++#define UHD_TT_THINK_24 0x0040 ++#define UHD_TT_THINK_32 0x0060 ++#define UHD_PORT_IND 0x0080 ++ uByte bPwrOn2PwrGood; /* delay in 2 ms units */ ++#define UHD_PWRON_FACTOR 2 ++ uByte bHubContrCurrent; ++ uByte DeviceRemovable[32]; /* max 255 ports */ ++#define UHD_NOT_REMOV(desc, i) \ ++ (((desc)->DeviceRemovable[(i)/8] >> ((i) % 8)) & 1) ++ /* deprecated */ uByte PortPowerCtrlMask[1]; ++} UPACKED usb_hub_descriptor_t; ++#define USB_HUB_DESCRIPTOR_SIZE 9 /* includes deprecated PortPowerCtrlMask */ ++ ++typedef struct { ++ uByte bLength; ++ uByte bDescriptorType; ++ uWord bcdUSB; ++ uByte bDeviceClass; ++ uByte bDeviceSubClass; ++ uByte bDeviceProtocol; ++ uByte bMaxPacketSize0; ++ uByte bNumConfigurations; ++ uByte bReserved; ++} UPACKED usb_device_qualifier_t; ++#define USB_DEVICE_QUALIFIER_SIZE 10 ++ ++typedef struct { ++ uByte bLength; ++ uByte bDescriptorType; ++ uByte bmAttributes; ++#define UOTG_SRP 0x01 ++#define UOTG_HNP 0x02 ++} UPACKED usb_otg_descriptor_t; ++ ++/* OTG feature selectors */ ++#define UOTG_B_HNP_ENABLE 3 ++#define UOTG_A_HNP_SUPPORT 4 ++#define UOTG_A_ALT_HNP_SUPPORT 5 ++ ++typedef struct { ++ uWord wStatus; ++/* Device status flags */ ++#define UDS_SELF_POWERED 0x0001 ++#define UDS_REMOTE_WAKEUP 0x0002 ++/* Endpoint status flags */ ++#define UES_HALT 0x0001 ++} UPACKED usb_status_t; ++ ++typedef struct { ++ uWord wHubStatus; ++#define UHS_LOCAL_POWER 0x0001 ++#define UHS_OVER_CURRENT 0x0002 ++ uWord wHubChange; ++} UPACKED usb_hub_status_t; ++ ++typedef struct { ++ uWord wPortStatus; ++#define UPS_CURRENT_CONNECT_STATUS 0x0001 ++#define UPS_PORT_ENABLED 0x0002 ++#define UPS_SUSPEND 0x0004 ++#define UPS_OVERCURRENT_INDICATOR 0x0008 ++#define UPS_RESET 0x0010 ++#define UPS_PORT_POWER 0x0100 ++#define UPS_LOW_SPEED 0x0200 ++#define UPS_HIGH_SPEED 0x0400 ++#define UPS_PORT_TEST 0x0800 ++#define UPS_PORT_INDICATOR 0x1000 ++ uWord wPortChange; ++#define UPS_C_CONNECT_STATUS 0x0001 ++#define UPS_C_PORT_ENABLED 0x0002 ++#define UPS_C_SUSPEND 0x0004 ++#define UPS_C_OVERCURRENT_INDICATOR 0x0008 ++#define UPS_C_PORT_RESET 0x0010 ++} UPACKED usb_port_status_t; ++ ++#ifdef _MSC_VER ++#include ++#endif ++ ++/* Device class codes */ ++#define UDCLASS_IN_INTERFACE 0x00 ++#define UDCLASS_COMM 0x02 ++#define UDCLASS_HUB 0x09 ++#define UDSUBCLASS_HUB 0x00 ++#define UDPROTO_FSHUB 0x00 ++#define UDPROTO_HSHUBSTT 0x01 ++#define UDPROTO_HSHUBMTT 0x02 ++#define UDCLASS_DIAGNOSTIC 0xdc ++#define UDCLASS_WIRELESS 0xe0 ++#define UDSUBCLASS_RF 0x01 ++#define UDPROTO_BLUETOOTH 0x01 ++#define UDCLASS_VENDOR 0xff ++ ++/* Interface class codes */ ++#define UICLASS_UNSPEC 0x00 ++ ++#define UICLASS_AUDIO 0x01 ++#define UISUBCLASS_AUDIOCONTROL 1 ++#define UISUBCLASS_AUDIOSTREAM 2 ++#define UISUBCLASS_MIDISTREAM 3 ++ ++#define UICLASS_CDC 0x02 /* communication */ ++#define UISUBCLASS_DIRECT_LINE_CONTROL_MODEL 1 ++#define UISUBCLASS_ABSTRACT_CONTROL_MODEL 2 ++#define UISUBCLASS_TELEPHONE_CONTROL_MODEL 3 ++#define UISUBCLASS_MULTICHANNEL_CONTROL_MODEL 4 ++#define UISUBCLASS_CAPI_CONTROLMODEL 5 ++#define UISUBCLASS_ETHERNET_NETWORKING_CONTROL_MODEL 6 ++#define UISUBCLASS_ATM_NETWORKING_CONTROL_MODEL 7 ++#define UIPROTO_CDC_AT 1 ++ ++#define UICLASS_HID 0x03 ++#define UISUBCLASS_BOOT 1 ++#define UIPROTO_BOOT_KEYBOARD 1 ++ ++#define UICLASS_PHYSICAL 0x05 ++ ++#define UICLASS_IMAGE 0x06 ++ ++#define UICLASS_PRINTER 0x07 ++#define UISUBCLASS_PRINTER 1 ++#define UIPROTO_PRINTER_UNI 1 ++#define UIPROTO_PRINTER_BI 2 ++#define UIPROTO_PRINTER_1284 3 ++ ++#define UICLASS_MASS 0x08 ++#define UISUBCLASS_RBC 1 ++#define UISUBCLASS_SFF8020I 2 ++#define UISUBCLASS_QIC157 3 ++#define UISUBCLASS_UFI 4 ++#define UISUBCLASS_SFF8070I 5 ++#define UISUBCLASS_SCSI 6 ++#define UIPROTO_MASS_CBI_I 0 ++#define UIPROTO_MASS_CBI 1 ++#define UIPROTO_MASS_BBB_OLD 2 /* Not in the spec anymore */ ++#define UIPROTO_MASS_BBB 80 /* 'P' for the Iomega Zip drive */ ++ ++#define UICLASS_HUB 0x09 ++#define UISUBCLASS_HUB 0 ++#define UIPROTO_FSHUB 0 ++#define UIPROTO_HSHUBSTT 0 /* Yes, same as previous */ ++#define UIPROTO_HSHUBMTT 1 ++ ++#define UICLASS_CDC_DATA 0x0a ++#define UISUBCLASS_DATA 0 ++#define UIPROTO_DATA_ISDNBRI 0x30 /* Physical iface */ ++#define UIPROTO_DATA_HDLC 0x31 /* HDLC */ ++#define UIPROTO_DATA_TRANSPARENT 0x32 /* Transparent */ ++#define UIPROTO_DATA_Q921M 0x50 /* Management for Q921 */ ++#define UIPROTO_DATA_Q921 0x51 /* Data for Q921 */ ++#define UIPROTO_DATA_Q921TM 0x52 /* TEI multiplexer for Q921 */ ++#define UIPROTO_DATA_V42BIS 0x90 /* Data compression */ ++#define UIPROTO_DATA_Q931 0x91 /* Euro-ISDN */ ++#define UIPROTO_DATA_V120 0x92 /* V.24 rate adaption */ ++#define UIPROTO_DATA_CAPI 0x93 /* CAPI 2.0 commands */ ++#define UIPROTO_DATA_HOST_BASED 0xfd /* Host based driver */ ++#define UIPROTO_DATA_PUF 0xfe /* see Prot. Unit Func. Desc.*/ ++#define UIPROTO_DATA_VENDOR 0xff /* Vendor specific */ ++ ++#define UICLASS_SMARTCARD 0x0b ++ ++/*#define UICLASS_FIRM_UPD 0x0c*/ ++ ++#define UICLASS_SECURITY 0x0d ++ ++#define UICLASS_DIAGNOSTIC 0xdc ++ ++#define UICLASS_WIRELESS 0xe0 ++#define UISUBCLASS_RF 0x01 ++#define UIPROTO_BLUETOOTH 0x01 ++ ++#define UICLASS_APPL_SPEC 0xfe ++#define UISUBCLASS_FIRMWARE_DOWNLOAD 1 ++#define UISUBCLASS_IRDA 2 ++#define UIPROTO_IRDA 0 ++ ++#define UICLASS_VENDOR 0xff ++ ++#define USB_HUB_MAX_DEPTH 5 ++ ++/* ++ * Minimum time a device needs to be powered down to go through ++ * a power cycle. XXX Are these time in the spec? ++ */ ++#define USB_POWER_DOWN_TIME 200 /* ms */ ++#define USB_PORT_POWER_DOWN_TIME 100 /* ms */ ++ ++#if 0 ++/* These are the values from the spec. */ ++#define USB_PORT_RESET_DELAY 10 /* ms */ ++#define USB_PORT_ROOT_RESET_DELAY 50 /* ms */ ++#define USB_PORT_RESET_RECOVERY 10 /* ms */ ++#define USB_PORT_POWERUP_DELAY 100 /* ms */ ++#define USB_SET_ADDRESS_SETTLE 2 /* ms */ ++#define USB_RESUME_DELAY (20*5) /* ms */ ++#define USB_RESUME_WAIT 10 /* ms */ ++#define USB_RESUME_RECOVERY 10 /* ms */ ++#define USB_EXTRA_POWER_UP_TIME 0 /* ms */ ++#else ++/* Allow for marginal (i.e. non-conforming) devices. */ ++#define USB_PORT_RESET_DELAY 50 /* ms */ ++#define USB_PORT_ROOT_RESET_DELAY 250 /* ms */ ++#define USB_PORT_RESET_RECOVERY 250 /* ms */ ++#define USB_PORT_POWERUP_DELAY 300 /* ms */ ++#define USB_SET_ADDRESS_SETTLE 10 /* ms */ ++#define USB_RESUME_DELAY (50*5) /* ms */ ++#define USB_RESUME_WAIT 50 /* ms */ ++#define USB_RESUME_RECOVERY 50 /* ms */ ++#define USB_EXTRA_POWER_UP_TIME 20 /* ms */ ++#endif ++ ++#define USB_MIN_POWER 100 /* mA */ ++#define USB_MAX_POWER 500 /* mA */ ++ ++#define USB_BUS_RESET_DELAY 100 /* ms XXX?*/ ++ ++#define USB_UNCONFIG_NO 0 ++#define USB_UNCONFIG_INDEX (-1) ++ ++/*** ioctl() related stuff ***/ ++ ++struct usb_ctl_request { ++ int ucr_addr; ++ usb_device_request_t ucr_request; ++ void *ucr_data; ++ int ucr_flags; ++#define USBD_SHORT_XFER_OK 0x04 /* allow short reads */ ++ int ucr_actlen; /* actual length transferred */ ++}; ++ ++struct usb_alt_interface { ++ int uai_config_index; ++ int uai_interface_index; ++ int uai_alt_no; ++}; ++ ++#define USB_CURRENT_CONFIG_INDEX (-1) ++#define USB_CURRENT_ALT_INDEX (-1) ++ ++struct usb_config_desc { ++ int ucd_config_index; ++ usb_config_descriptor_t ucd_desc; ++}; ++ ++struct usb_interface_desc { ++ int uid_config_index; ++ int uid_interface_index; ++ int uid_alt_index; ++ usb_interface_descriptor_t uid_desc; ++}; ++ ++struct usb_endpoint_desc { ++ int ued_config_index; ++ int ued_interface_index; ++ int ued_alt_index; ++ int ued_endpoint_index; ++ usb_endpoint_descriptor_t ued_desc; ++}; ++ ++struct usb_full_desc { ++ int ufd_config_index; ++ u_int ufd_size; ++ u_char *ufd_data; ++}; ++ ++struct usb_string_desc { ++ int usd_string_index; ++ int usd_language_id; ++ usb_string_descriptor_t usd_desc; ++}; ++ ++struct usb_ctl_report_desc { ++ int ucrd_size; ++ u_char ucrd_data[1024]; /* filled data size will vary */ ++}; ++ ++typedef struct { u_int32_t cookie; } usb_event_cookie_t; ++ ++#define USB_MAX_DEVNAMES 4 ++#define USB_MAX_DEVNAMELEN 16 ++struct usb_device_info { ++ u_int8_t udi_bus; ++ u_int8_t udi_addr; /* device address */ ++ usb_event_cookie_t udi_cookie; ++ char udi_product[USB_MAX_STRING_LEN]; ++ char udi_vendor[USB_MAX_STRING_LEN]; ++ char udi_release[8]; ++ u_int16_t udi_productNo; ++ u_int16_t udi_vendorNo; ++ u_int16_t udi_releaseNo; ++ u_int8_t udi_class; ++ u_int8_t udi_subclass; ++ u_int8_t udi_protocol; ++ u_int8_t udi_config; ++ u_int8_t udi_speed; ++#define USB_SPEED_UNKNOWN 0 ++#define USB_SPEED_LOW 1 ++#define USB_SPEED_FULL 2 ++#define USB_SPEED_HIGH 3 ++#define USB_SPEED_VARIABLE 4 ++#define USB_SPEED_SUPER 5 ++ int udi_power; /* power consumption in mA, 0 if selfpowered */ ++ int udi_nports; ++ char udi_devnames[USB_MAX_DEVNAMES][USB_MAX_DEVNAMELEN]; ++ u_int8_t udi_ports[16];/* hub only: addresses of devices on ports */ ++#define USB_PORT_ENABLED 0xff ++#define USB_PORT_SUSPENDED 0xfe ++#define USB_PORT_POWERED 0xfd ++#define USB_PORT_DISABLED 0xfc ++}; ++ ++struct usb_ctl_report { ++ int ucr_report; ++ u_char ucr_data[1024]; /* filled data size will vary */ ++}; ++ ++struct usb_device_stats { ++ u_long uds_requests[4]; /* indexed by transfer type UE_* */ ++}; ++ ++#define WUSB_MIN_IE 0x80 ++#define WUSB_WCTA_IE 0x80 ++#define WUSB_WCONNECTACK_IE 0x81 ++#define WUSB_WHOSTINFO_IE 0x82 ++#define WUHI_GET_CA(_bmAttributes_) ((_bmAttributes_) & 0x3) ++#define WUHI_CA_RECONN 0x00 ++#define WUHI_CA_LIMITED 0x01 ++#define WUHI_CA_ALL 0x03 ++#define WUHI_GET_MLSI(_bmAttributes_) (((_bmAttributes_) & 0x38) >> 3) ++#define WUSB_WCHCHANGEANNOUNCE_IE 0x83 ++#define WUSB_WDEV_DISCONNECT_IE 0x84 ++#define WUSB_WHOST_DISCONNECT_IE 0x85 ++#define WUSB_WRELEASE_CHANNEL_IE 0x86 ++#define WUSB_WWORK_IE 0x87 ++#define WUSB_WCHANNEL_STOP_IE 0x88 ++#define WUSB_WDEV_KEEPALIVE_IE 0x89 ++#define WUSB_WISOCH_DISCARD_IE 0x8A ++#define WUSB_WRESETDEVICE_IE 0x8B ++#define WUSB_WXMIT_PACKET_ADJUST_IE 0x8C ++#define WUSB_MAX_IE 0x8C ++ ++/* Device Notification Types */ ++ ++#define WUSB_DN_MIN 0x01 ++#define WUSB_DN_CONNECT 0x01 ++# define WUSB_DA_OLDCONN 0x00 ++# define WUSB_DA_NEWCONN 0x01 ++# define WUSB_DA_SELF_BEACON 0x02 ++# define WUSB_DA_DIR_BEACON 0x04 ++# define WUSB_DA_NO_BEACON 0x06 ++#define WUSB_DN_DISCONNECT 0x02 ++#define WUSB_DN_EPRDY 0x03 ++#define WUSB_DN_MASAVAILCHANGED 0x04 ++#define WUSB_DN_REMOTEWAKEUP 0x05 ++#define WUSB_DN_SLEEP 0x06 ++#define WUSB_DN_ALIVE 0x07 ++#define WUSB_DN_MAX 0x07 ++ ++#ifdef _MSC_VER ++#include ++#endif ++ ++/* WUSB Handshake Data. Used during the SET/GET HANDSHAKE requests */ ++typedef struct wusb_hndshk_data { ++ uByte bMessageNumber; ++ uByte bStatus; ++ uByte tTKID[3]; ++ uByte bReserved; ++ uByte CDID[16]; ++ uByte Nonce[16]; ++ uByte MIC[8]; ++} UPACKED wusb_hndshk_data_t; ++#define WUSB_HANDSHAKE_LEN_FOR_MIC 38 ++ ++/* WUSB Connection Context */ ++typedef struct wusb_conn_context { ++ uByte CHID [16]; ++ uByte CDID [16]; ++ uByte CK [16]; ++} UPACKED wusb_conn_context_t; ++ ++/* WUSB Security Descriptor */ ++typedef struct wusb_security_desc { ++ uByte bLength; ++ uByte bDescriptorType; ++ uWord wTotalLength; ++ uByte bNumEncryptionTypes; ++} UPACKED wusb_security_desc_t; ++ ++/* WUSB Encryption Type Descriptor */ ++typedef struct wusb_encrypt_type_desc { ++ uByte bLength; ++ uByte bDescriptorType; ++ ++ uByte bEncryptionType; ++#define WUETD_UNSECURE 0 ++#define WUETD_WIRED 1 ++#define WUETD_CCM_1 2 ++#define WUETD_RSA_1 3 ++ ++ uByte bEncryptionValue; ++ uByte bAuthKeyIndex; ++} UPACKED wusb_encrypt_type_desc_t; ++ ++/* WUSB Key Descriptor */ ++typedef struct wusb_key_desc { ++ uByte bLength; ++ uByte bDescriptorType; ++ uByte tTKID[3]; ++ uByte bReserved; ++ uByte KeyData[1]; /* variable length */ ++} UPACKED wusb_key_desc_t; ++ ++/* WUSB BOS Descriptor (Binary device Object Store) */ ++typedef struct wusb_bos_desc { ++ uByte bLength; ++ uByte bDescriptorType; ++ uWord wTotalLength; ++ uByte bNumDeviceCaps; ++} UPACKED wusb_bos_desc_t; ++ ++#define USB_DEVICE_CAPABILITY_20_EXTENSION 0x02 ++typedef struct usb_dev_cap_20_ext_desc { ++ uByte bLength; ++ uByte bDescriptorType; ++ uByte bDevCapabilityType; ++#define USB_20_EXT_LPM 0x02 ++ uDWord bmAttributes; ++} UPACKED usb_dev_cap_20_ext_desc_t; ++ ++#define USB_DEVICE_CAPABILITY_SS_USB 0x03 ++typedef struct usb_dev_cap_ss_usb { ++ uByte bLength; ++ uByte bDescriptorType; ++ uByte bDevCapabilityType; ++#define USB_DC_SS_USB_LTM_CAPABLE 0x02 ++ uByte bmAttributes; ++#define USB_DC_SS_USB_SPEED_SUPPORT_LOW 0x01 ++#define USB_DC_SS_USB_SPEED_SUPPORT_FULL 0x02 ++#define USB_DC_SS_USB_SPEED_SUPPORT_HIGH 0x04 ++#define USB_DC_SS_USB_SPEED_SUPPORT_SS 0x08 ++ uWord wSpeedsSupported; ++ uByte bFunctionalitySupport; ++ uByte bU1DevExitLat; ++ uWord wU2DevExitLat; ++} UPACKED usb_dev_cap_ss_usb_t; ++ ++#define USB_DEVICE_CAPABILITY_CONTAINER_ID 0x04 ++typedef struct usb_dev_cap_container_id { ++ uByte bLength; ++ uByte bDescriptorType; ++ uByte bDevCapabilityType; ++ uByte bReserved; ++ uByte containerID[16]; ++} UPACKED usb_dev_cap_container_id_t; ++ ++/* Device Capability Type Codes */ ++#define WUSB_DEVICE_CAPABILITY_WIRELESS_USB 0x01 ++ ++/* Device Capability Descriptor */ ++typedef struct wusb_dev_cap_desc { ++ uByte bLength; ++ uByte bDescriptorType; ++ uByte bDevCapabilityType; ++ uByte caps[1]; /* Variable length */ ++} UPACKED wusb_dev_cap_desc_t; ++ ++/* Device Capability Descriptor */ ++typedef struct wusb_dev_cap_uwb_desc { ++ uByte bLength; ++ uByte bDescriptorType; ++ uByte bDevCapabilityType; ++ uByte bmAttributes; ++ uWord wPHYRates; /* Bitmap */ ++ uByte bmTFITXPowerInfo; ++ uByte bmFFITXPowerInfo; ++ uWord bmBandGroup; ++ uByte bReserved; ++} UPACKED wusb_dev_cap_uwb_desc_t; ++ ++/* Wireless USB Endpoint Companion Descriptor */ ++typedef struct wusb_endpoint_companion_desc { ++ uByte bLength; ++ uByte bDescriptorType; ++ uByte bMaxBurst; ++ uByte bMaxSequence; ++ uWord wMaxStreamDelay; ++ uWord wOverTheAirPacketSize; ++ uByte bOverTheAirInterval; ++ uByte bmCompAttributes; ++} UPACKED wusb_endpoint_companion_desc_t; ++ ++/* Wireless USB Numeric Association M1 Data Structure */ ++typedef struct wusb_m1_data { ++ uByte version; ++ uWord langId; ++ uByte deviceFriendlyNameLength; ++ uByte sha_256_m3[32]; ++ uByte deviceFriendlyName[256]; ++} UPACKED wusb_m1_data_t; ++ ++typedef struct wusb_m2_data { ++ uByte version; ++ uWord langId; ++ uByte hostFriendlyNameLength; ++ uByte pkh[384]; ++ uByte hostFriendlyName[256]; ++} UPACKED wusb_m2_data_t; ++ ++typedef struct wusb_m3_data { ++ uByte pkd[384]; ++ uByte nd; ++} UPACKED wusb_m3_data_t; ++ ++typedef struct wusb_m4_data { ++ uDWord _attributeTypeIdAndLength_1; ++ uWord associationTypeId; ++ ++ uDWord _attributeTypeIdAndLength_2; ++ uWord associationSubTypeId; ++ ++ uDWord _attributeTypeIdAndLength_3; ++ uDWord length; ++ ++ uDWord _attributeTypeIdAndLength_4; ++ uDWord associationStatus; ++ ++ uDWord _attributeTypeIdAndLength_5; ++ uByte chid[16]; ++ ++ uDWord _attributeTypeIdAndLength_6; ++ uByte cdid[16]; ++ ++ uDWord _attributeTypeIdAndLength_7; ++ uByte bandGroups[2]; ++} UPACKED wusb_m4_data_t; ++ ++#ifdef _MSC_VER ++#include ++#endif ++ ++#ifdef __cplusplus ++} ++#endif ++ ++#endif /* _USB_H_ */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/Makefile +@@ -0,0 +1,85 @@ ++# ++# Makefile for DWC_otg Highspeed USB controller driver ++# ++ ++ifneq ($(KERNELRELEASE),) ++ ++# Use the BUS_INTERFACE variable to compile the software for either ++# PCI(PCI_INTERFACE) or LM(LM_INTERFACE) bus. ++ifeq ($(BUS_INTERFACE),) ++# BUS_INTERFACE = -DPCI_INTERFACE ++# BUS_INTERFACE = -DLM_INTERFACE ++ BUS_INTERFACE = -DPLATFORM_INTERFACE ++endif ++ ++#ccflags-y += -DDEBUG ++#ccflags-y += -DDWC_OTG_DEBUGLEV=1 # reduce common debug msgs ++ ++# Use one of the following flags to compile the software in host-only or ++# device-only mode. ++#ccflags-y += -DDWC_HOST_ONLY ++#ccflags-y += -DDWC_DEVICE_ONLY ++ ++ccflags-y += -Dlinux -DDWC_HS_ELECT_TST ++#ccflags-y += -DDWC_EN_ISOC ++ccflags-y += -I$(srctree)/drivers/usb/host/dwc_common_port ++#ccflags-y += -I$(PORTLIB) ++ccflags-y += -DDWC_LINUX ++ccflags-y += $(CFI) ++ccflags-y += $(BUS_INTERFACE) ++#ccflags-y += -DDWC_DEV_SRPCAP ++ ++obj-$(CONFIG_USB_DWCOTG) += dwc_otg.o ++ ++dwc_otg-objs := dwc_otg_driver.o dwc_otg_attr.o ++dwc_otg-objs += dwc_otg_cil.o dwc_otg_cil_intr.o ++dwc_otg-objs += dwc_otg_pcd_linux.o dwc_otg_pcd.o dwc_otg_pcd_intr.o ++dwc_otg-objs += dwc_otg_hcd.o dwc_otg_hcd_linux.o dwc_otg_hcd_intr.o dwc_otg_hcd_queue.o dwc_otg_hcd_ddma.o ++dwc_otg-objs += dwc_otg_adp.o ++dwc_otg-objs += dwc_otg_fiq_fsm.o ++ifneq ($(CONFIG_ARM64),y) ++dwc_otg-objs += dwc_otg_fiq_stub.o ++endif ++ ++ifneq ($(CFI),) ++dwc_otg-objs += dwc_otg_cfi.o ++endif ++ ++kernrelwd := $(subst ., ,$(KERNELRELEASE)) ++kernrel3 := $(word 1,$(kernrelwd)).$(word 2,$(kernrelwd)).$(word 3,$(kernrelwd)) ++ ++ifneq ($(kernrel3),2.6.20) ++ccflags-y += $(CPPFLAGS) ++endif ++ ++else ++ ++PWD := $(shell pwd) ++PORTLIB := $(PWD)/../dwc_common_port ++ ++# Command paths ++CTAGS := $(CTAGS) ++DOXYGEN := $(DOXYGEN) ++ ++default: portlib ++ $(MAKE) -C$(KDIR) M=$(PWD) ARCH=$(ARCH) CROSS_COMPILE=$(CROSS_COMPILE) modules ++ ++install: default ++ $(MAKE) -C$(KDIR) M=$(PORTLIB) modules_install ++ $(MAKE) -C$(KDIR) M=$(PWD) modules_install ++ ++portlib: ++ $(MAKE) -C$(KDIR) M=$(PORTLIB) ARCH=$(ARCH) CROSS_COMPILE=$(CROSS_COMPILE) modules ++ cp $(PORTLIB)/Module.symvers $(PWD)/ ++ ++docs: $(wildcard *.[hc]) doc/doxygen.cfg ++ $(DOXYGEN) doc/doxygen.cfg ++ ++tags: $(wildcard *.[hc]) ++ $(CTAGS) -e $(wildcard *.[hc]) $(wildcard linux/*.[hc]) $(wildcard $(KDIR)/include/linux/usb*.h) ++ ++ ++clean: ++ rm -rf *.o *.ko .*cmd *.mod.c .tmp_versions Module.symvers ++ ++endif +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/doc/doxygen.cfg +@@ -0,0 +1,224 @@ ++# Doxyfile 1.3.9.1 ++ ++#--------------------------------------------------------------------------- ++# Project related configuration options ++#--------------------------------------------------------------------------- ++PROJECT_NAME = "DesignWare USB 2.0 OTG Controller (DWC_otg) Device Driver" ++PROJECT_NUMBER = v3.00a ++OUTPUT_DIRECTORY = ./doc/ ++CREATE_SUBDIRS = NO ++OUTPUT_LANGUAGE = English ++BRIEF_MEMBER_DESC = YES ++REPEAT_BRIEF = YES ++ABBREVIATE_BRIEF = "The $name class" \ ++ "The $name widget" \ ++ "The $name file" \ ++ is \ ++ provides \ ++ specifies \ ++ contains \ ++ represents \ ++ a \ ++ an \ ++ the ++ALWAYS_DETAILED_SEC = NO ++INLINE_INHERITED_MEMB = NO ++FULL_PATH_NAMES = NO ++STRIP_FROM_PATH = ++STRIP_FROM_INC_PATH = ++SHORT_NAMES = NO ++JAVADOC_AUTOBRIEF = YES ++MULTILINE_CPP_IS_BRIEF = NO ++INHERIT_DOCS = YES ++DISTRIBUTE_GROUP_DOC = NO ++TAB_SIZE = 8 ++ALIASES = ++OPTIMIZE_OUTPUT_FOR_C = YES ++OPTIMIZE_OUTPUT_JAVA = NO ++SUBGROUPING = YES ++#--------------------------------------------------------------------------- ++# Build related configuration options ++#--------------------------------------------------------------------------- ++EXTRACT_ALL = NO ++EXTRACT_PRIVATE = YES ++EXTRACT_STATIC = YES ++EXTRACT_LOCAL_CLASSES = YES ++EXTRACT_LOCAL_METHODS = NO ++HIDE_UNDOC_MEMBERS = NO ++HIDE_UNDOC_CLASSES = NO ++HIDE_FRIEND_COMPOUNDS = NO ++HIDE_IN_BODY_DOCS = NO ++INTERNAL_DOCS = NO ++CASE_SENSE_NAMES = NO ++HIDE_SCOPE_NAMES = NO ++SHOW_INCLUDE_FILES = YES ++INLINE_INFO = YES ++SORT_MEMBER_DOCS = NO ++SORT_BRIEF_DOCS = NO ++SORT_BY_SCOPE_NAME = NO ++GENERATE_TODOLIST = YES ++GENERATE_TESTLIST = YES ++GENERATE_BUGLIST = YES ++GENERATE_DEPRECATEDLIST= YES ++ENABLED_SECTIONS = ++MAX_INITIALIZER_LINES = 30 ++SHOW_USED_FILES = YES ++SHOW_DIRECTORIES = YES ++#--------------------------------------------------------------------------- ++# configuration options related to warning and progress messages ++#--------------------------------------------------------------------------- ++QUIET = YES ++WARNINGS = YES ++WARN_IF_UNDOCUMENTED = NO ++WARN_IF_DOC_ERROR = YES ++WARN_FORMAT = "$file:$line: $text" ++WARN_LOGFILE = ++#--------------------------------------------------------------------------- ++# configuration options related to the input files ++#--------------------------------------------------------------------------- ++INPUT = . ++FILE_PATTERNS = *.c \ ++ *.h \ ++ ./linux/*.c \ ++ ./linux/*.h ++RECURSIVE = NO ++EXCLUDE = ./test/ \ ++ ./dwc_otg/.AppleDouble/ ++EXCLUDE_SYMLINKS = YES ++EXCLUDE_PATTERNS = *.mod.* ++EXAMPLE_PATH = ++EXAMPLE_PATTERNS = * ++EXAMPLE_RECURSIVE = NO ++IMAGE_PATH = ++INPUT_FILTER = ++FILTER_PATTERNS = ++FILTER_SOURCE_FILES = NO ++#--------------------------------------------------------------------------- ++# configuration options related to source browsing ++#--------------------------------------------------------------------------- ++SOURCE_BROWSER = YES ++INLINE_SOURCES = NO ++STRIP_CODE_COMMENTS = YES ++REFERENCED_BY_RELATION = NO ++REFERENCES_RELATION = NO ++VERBATIM_HEADERS = NO ++#--------------------------------------------------------------------------- ++# configuration options related to the alphabetical class index ++#--------------------------------------------------------------------------- ++ALPHABETICAL_INDEX = NO ++COLS_IN_ALPHA_INDEX = 5 ++IGNORE_PREFIX = ++#--------------------------------------------------------------------------- ++# configuration options related to the HTML output ++#--------------------------------------------------------------------------- ++GENERATE_HTML = YES ++HTML_OUTPUT = html ++HTML_FILE_EXTENSION = .html ++HTML_HEADER = ++HTML_FOOTER = ++HTML_STYLESHEET = ++HTML_ALIGN_MEMBERS = YES ++GENERATE_HTMLHELP = NO ++CHM_FILE = ++HHC_LOCATION = ++GENERATE_CHI = NO ++BINARY_TOC = NO ++TOC_EXPAND = NO ++DISABLE_INDEX = NO ++ENUM_VALUES_PER_LINE = 4 ++GENERATE_TREEVIEW = YES ++TREEVIEW_WIDTH = 250 ++#--------------------------------------------------------------------------- ++# configuration options related to the LaTeX output ++#--------------------------------------------------------------------------- ++GENERATE_LATEX = NO ++LATEX_OUTPUT = latex ++LATEX_CMD_NAME = latex ++MAKEINDEX_CMD_NAME = makeindex ++COMPACT_LATEX = NO ++PAPER_TYPE = a4wide ++EXTRA_PACKAGES = ++LATEX_HEADER = ++PDF_HYPERLINKS = NO ++USE_PDFLATEX = NO ++LATEX_BATCHMODE = NO ++LATEX_HIDE_INDICES = NO ++#--------------------------------------------------------------------------- ++# configuration options related to the RTF output ++#--------------------------------------------------------------------------- ++GENERATE_RTF = NO ++RTF_OUTPUT = rtf ++COMPACT_RTF = NO ++RTF_HYPERLINKS = NO ++RTF_STYLESHEET_FILE = ++RTF_EXTENSIONS_FILE = ++#--------------------------------------------------------------------------- ++# configuration options related to the man page output ++#--------------------------------------------------------------------------- ++GENERATE_MAN = NO ++MAN_OUTPUT = man ++MAN_EXTENSION = .3 ++MAN_LINKS = NO ++#--------------------------------------------------------------------------- ++# configuration options related to the XML output ++#--------------------------------------------------------------------------- ++GENERATE_XML = NO ++XML_OUTPUT = xml ++XML_SCHEMA = ++XML_DTD = ++XML_PROGRAMLISTING = YES ++#--------------------------------------------------------------------------- ++# configuration options for the AutoGen Definitions output ++#--------------------------------------------------------------------------- ++GENERATE_AUTOGEN_DEF = NO ++#--------------------------------------------------------------------------- ++# configuration options related to the Perl module output ++#--------------------------------------------------------------------------- ++GENERATE_PERLMOD = NO ++PERLMOD_LATEX = NO ++PERLMOD_PRETTY = YES ++PERLMOD_MAKEVAR_PREFIX = ++#--------------------------------------------------------------------------- ++# Configuration options related to the preprocessor ++#--------------------------------------------------------------------------- ++ENABLE_PREPROCESSING = YES ++MACRO_EXPANSION = YES ++EXPAND_ONLY_PREDEF = YES ++SEARCH_INCLUDES = YES ++INCLUDE_PATH = ++INCLUDE_FILE_PATTERNS = ++PREDEFINED = DEVICE_ATTR DWC_EN_ISOC ++EXPAND_AS_DEFINED = DWC_OTG_DEVICE_ATTR_BITFIELD_SHOW DWC_OTG_DEVICE_ATTR_BITFIELD_STORE DWC_OTG_DEVICE_ATTR_BITFIELD_RW DWC_OTG_DEVICE_ATTR_BITFIELD_RO DWC_OTG_DEVICE_ATTR_REG_SHOW DWC_OTG_DEVICE_ATTR_REG_STORE DWC_OTG_DEVICE_ATTR_REG32_RW DWC_OTG_DEVICE_ATTR_REG32_RO DWC_EN_ISOC ++SKIP_FUNCTION_MACROS = NO ++#--------------------------------------------------------------------------- ++# Configuration::additions related to external references ++#--------------------------------------------------------------------------- ++TAGFILES = ++GENERATE_TAGFILE = ++ALLEXTERNALS = NO ++EXTERNAL_GROUPS = YES ++PERL_PATH = /usr/bin/perl ++#--------------------------------------------------------------------------- ++# Configuration options related to the dot tool ++#--------------------------------------------------------------------------- ++CLASS_DIAGRAMS = YES ++HIDE_UNDOC_RELATIONS = YES ++HAVE_DOT = NO ++CLASS_GRAPH = YES ++COLLABORATION_GRAPH = YES ++UML_LOOK = NO ++TEMPLATE_RELATIONS = NO ++INCLUDE_GRAPH = YES ++INCLUDED_BY_GRAPH = YES ++CALL_GRAPH = NO ++GRAPHICAL_HIERARCHY = YES ++DOT_IMAGE_FORMAT = png ++DOT_PATH = ++DOTFILE_DIRS = ++MAX_DOT_GRAPH_DEPTH = 1000 ++GENERATE_LEGEND = YES ++DOT_CLEANUP = YES ++#--------------------------------------------------------------------------- ++# Configuration::additions related to the search engine ++#--------------------------------------------------------------------------- ++SEARCHENGINE = NO +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dummy_audio.c +@@ -0,0 +1,1574 @@ ++/* ++ * zero.c -- Gadget Zero, for USB development ++ * ++ * Copyright (C) 2003-2004 David Brownell ++ * All rights reserved. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions ++ * are met: ++ * 1. Redistributions of source code must retain the above copyright ++ * notice, this list of conditions, and the following disclaimer, ++ * without modification. ++ * 2. Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in the ++ * documentation and/or other materials provided with the distribution. ++ * 3. The names of the above-listed copyright holders may not be used ++ * to endorse or promote products derived from this software without ++ * specific prior written permission. ++ * ++ * ALTERNATIVELY, this software may be distributed under the terms of the ++ * GNU General Public License ("GPL") as published by the Free Software ++ * Foundation, either version 2 of that License or (at your option) any ++ * later version. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS ++ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ++ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR ++ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR ++ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF ++ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING ++ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ */ ++ ++ ++/* ++ * Gadget Zero only needs two bulk endpoints, and is an example of how you ++ * can write a hardware-agnostic gadget driver running inside a USB device. ++ * ++ * Hardware details are visible (see CONFIG_USB_ZERO_* below) but don't ++ * affect most of the driver. ++ * ++ * Use it with the Linux host/master side "usbtest" driver to get a basic ++ * functional test of your device-side usb stack, or with "usb-skeleton". ++ * ++ * It supports two similar configurations. One sinks whatever the usb host ++ * writes, and in return sources zeroes. The other loops whatever the host ++ * writes back, so the host can read it. Module options include: ++ * ++ * buflen=N default N=4096, buffer size used ++ * qlen=N default N=32, how many buffers in the loopback queue ++ * loopdefault default false, list loopback config first ++ * ++ * Many drivers will only have one configuration, letting them be much ++ * simpler if they also don't support high speed operation (like this ++ * driver does). ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++ ++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,21) ++# include ++#else ++# include ++#endif ++ ++#include ++ ++ ++/*-------------------------------------------------------------------------*/ ++/*-------------------------------------------------------------------------*/ ++ ++ ++static int utf8_to_utf16le(const char *s, u16 *cp, unsigned len) ++{ ++ int count = 0; ++ u8 c; ++ u16 uchar; ++ ++ /* this insists on correct encodings, though not minimal ones. ++ * BUT it currently rejects legit 4-byte UTF-8 code points, ++ * which need surrogate pairs. (Unicode 3.1 can use them.) ++ */ ++ while (len != 0 && (c = (u8) *s++) != 0) { ++ if (unlikely(c & 0x80)) { ++ // 2-byte sequence: ++ // 00000yyyyyxxxxxx = 110yyyyy 10xxxxxx ++ if ((c & 0xe0) == 0xc0) { ++ uchar = (c & 0x1f) << 6; ++ ++ c = (u8) *s++; ++ if ((c & 0xc0) != 0xc0) ++ goto fail; ++ c &= 0x3f; ++ uchar |= c; ++ ++ // 3-byte sequence (most CJKV characters): ++ // zzzzyyyyyyxxxxxx = 1110zzzz 10yyyyyy 10xxxxxx ++ } else if ((c & 0xf0) == 0xe0) { ++ uchar = (c & 0x0f) << 12; ++ ++ c = (u8) *s++; ++ if ((c & 0xc0) != 0xc0) ++ goto fail; ++ c &= 0x3f; ++ uchar |= c << 6; ++ ++ c = (u8) *s++; ++ if ((c & 0xc0) != 0xc0) ++ goto fail; ++ c &= 0x3f; ++ uchar |= c; ++ ++ /* no bogus surrogates */ ++ if (0xd800 <= uchar && uchar <= 0xdfff) ++ goto fail; ++ ++ // 4-byte sequence (surrogate pairs, currently rare): ++ // 11101110wwwwzzzzyy + 110111yyyyxxxxxx ++ // = 11110uuu 10uuzzzz 10yyyyyy 10xxxxxx ++ // (uuuuu = wwww + 1) ++ // FIXME accept the surrogate code points (only) ++ ++ } else ++ goto fail; ++ } else ++ uchar = c; ++ put_unaligned (cpu_to_le16 (uchar), cp++); ++ count++; ++ len--; ++ } ++ return count; ++fail: ++ return -1; ++} ++ ++ ++/** ++ * usb_gadget_get_string - fill out a string descriptor ++ * @table: of c strings encoded using UTF-8 ++ * @id: string id, from low byte of wValue in get string descriptor ++ * @buf: at least 256 bytes ++ * ++ * Finds the UTF-8 string matching the ID, and converts it into a ++ * string descriptor in utf16-le. ++ * Returns length of descriptor (always even) or negative errno ++ * ++ * If your driver needs stings in multiple languages, you'll probably ++ * "switch (wIndex) { ... }" in your ep0 string descriptor logic, ++ * using this routine after choosing which set of UTF-8 strings to use. ++ * Note that US-ASCII is a strict subset of UTF-8; any string bytes with ++ * the eighth bit set will be multibyte UTF-8 characters, not ISO-8859/1 ++ * characters (which are also widely used in C strings). ++ */ ++int ++usb_gadget_get_string (struct usb_gadget_strings *table, int id, u8 *buf) ++{ ++ struct usb_string *s; ++ int len; ++ ++ /* descriptor 0 has the language id */ ++ if (id == 0) { ++ buf [0] = 4; ++ buf [1] = USB_DT_STRING; ++ buf [2] = (u8) table->language; ++ buf [3] = (u8) (table->language >> 8); ++ return 4; ++ } ++ for (s = table->strings; s && s->s; s++) ++ if (s->id == id) ++ break; ++ ++ /* unrecognized: stall. */ ++ if (!s || !s->s) ++ return -EINVAL; ++ ++ /* string descriptors have length, tag, then UTF16-LE text */ ++ len = min ((size_t) 126, strlen (s->s)); ++ memset (buf + 2, 0, 2 * len); /* zero all the bytes */ ++ len = utf8_to_utf16le(s->s, (u16 *)&buf[2], len); ++ if (len < 0) ++ return -EINVAL; ++ buf [0] = (len + 1) * 2; ++ buf [1] = USB_DT_STRING; ++ return buf [0]; ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++/*-------------------------------------------------------------------------*/ ++ ++ ++/** ++ * usb_descriptor_fillbuf - fill buffer with descriptors ++ * @buf: Buffer to be filled ++ * @buflen: Size of buf ++ * @src: Array of descriptor pointers, terminated by null pointer. ++ * ++ * Copies descriptors into the buffer, returning the length or a ++ * negative error code if they can't all be copied. Useful when ++ * assembling descriptors for an associated set of interfaces used ++ * as part of configuring a composite device; or in other cases where ++ * sets of descriptors need to be marshaled. ++ */ ++int ++usb_descriptor_fillbuf(void *buf, unsigned buflen, ++ const struct usb_descriptor_header **src) ++{ ++ u8 *dest = buf; ++ ++ if (!src) ++ return -EINVAL; ++ ++ /* fill buffer from src[] until null descriptor ptr */ ++ for (; 0 != *src; src++) { ++ unsigned len = (*src)->bLength; ++ ++ if (len > buflen) ++ return -EINVAL; ++ memcpy(dest, *src, len); ++ buflen -= len; ++ dest += len; ++ } ++ return dest - (u8 *)buf; ++} ++ ++ ++/** ++ * usb_gadget_config_buf - builts a complete configuration descriptor ++ * @config: Header for the descriptor, including characteristics such ++ * as power requirements and number of interfaces. ++ * @desc: Null-terminated vector of pointers to the descriptors (interface, ++ * endpoint, etc) defining all functions in this device configuration. ++ * @buf: Buffer for the resulting configuration descriptor. ++ * @length: Length of buffer. If this is not big enough to hold the ++ * entire configuration descriptor, an error code will be returned. ++ * ++ * This copies descriptors into the response buffer, building a descriptor ++ * for that configuration. It returns the buffer length or a negative ++ * status code. The config.wTotalLength field is set to match the length ++ * of the result, but other descriptor fields (including power usage and ++ * interface count) must be set by the caller. ++ * ++ * Gadget drivers could use this when constructing a config descriptor ++ * in response to USB_REQ_GET_DESCRIPTOR. They will need to patch the ++ * resulting bDescriptorType value if USB_DT_OTHER_SPEED_CONFIG is needed. ++ */ ++int usb_gadget_config_buf( ++ const struct usb_config_descriptor *config, ++ void *buf, ++ unsigned length, ++ const struct usb_descriptor_header **desc ++) ++{ ++ struct usb_config_descriptor *cp = buf; ++ int len; ++ ++ /* config descriptor first */ ++ if (length < USB_DT_CONFIG_SIZE || !desc) ++ return -EINVAL; ++ *cp = *config; ++ ++ /* then interface/endpoint/class/vendor/... */ ++ len = usb_descriptor_fillbuf(USB_DT_CONFIG_SIZE + (u8*)buf, ++ length - USB_DT_CONFIG_SIZE, desc); ++ if (len < 0) ++ return len; ++ len += USB_DT_CONFIG_SIZE; ++ if (len > 0xffff) ++ return -EINVAL; ++ ++ /* patch up the config descriptor */ ++ cp->bLength = USB_DT_CONFIG_SIZE; ++ cp->bDescriptorType = USB_DT_CONFIG; ++ cp->wTotalLength = cpu_to_le16(len); ++ cp->bmAttributes |= USB_CONFIG_ATT_ONE; ++ return len; ++} ++ ++/*-------------------------------------------------------------------------*/ ++/*-------------------------------------------------------------------------*/ ++ ++ ++#define RBUF_LEN (1024*1024) ++static int rbuf_start; ++static int rbuf_len; ++static __u8 rbuf[RBUF_LEN]; ++ ++/*-------------------------------------------------------------------------*/ ++ ++#define DRIVER_VERSION "St Patrick's Day 2004" ++ ++static const char shortname [] = "zero"; ++static const char longname [] = "YAMAHA YST-MS35D USB Speaker "; ++ ++static const char source_sink [] = "source and sink data"; ++static const char loopback [] = "loop input to output"; ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* ++ * driver assumes self-powered hardware, and ++ * has no way for users to trigger remote wakeup. ++ * ++ * this version autoconfigures as much as possible, ++ * which is reasonable for most "bulk-only" drivers. ++ */ ++static const char *EP_IN_NAME; /* source */ ++static const char *EP_OUT_NAME; /* sink */ ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* big enough to hold our biggest descriptor */ ++#define USB_BUFSIZ 512 ++ ++struct zero_dev { ++ spinlock_t lock; ++ struct usb_gadget *gadget; ++ struct usb_request *req; /* for control responses */ ++ ++ /* when configured, we have one of two configs: ++ * - source data (in to host) and sink it (out from host) ++ * - or loop it back (out from host back in to host) ++ */ ++ u8 config; ++ struct usb_ep *in_ep, *out_ep; ++ ++ /* autoresume timer */ ++ struct timer_list resume; ++}; ++ ++#define xprintk(d,level,fmt,args...) \ ++ dev_printk(level , &(d)->gadget->dev , fmt , ## args) ++ ++#ifdef DEBUG ++#define DBG(dev,fmt,args...) \ ++ xprintk(dev , KERN_DEBUG , fmt , ## args) ++#else ++#define DBG(dev,fmt,args...) \ ++ do { } while (0) ++#endif /* DEBUG */ ++ ++#ifdef VERBOSE ++#define VDBG DBG ++#else ++#define VDBG(dev,fmt,args...) \ ++ do { } while (0) ++#endif /* VERBOSE */ ++ ++#define ERROR(dev,fmt,args...) \ ++ xprintk(dev , KERN_ERR , fmt , ## args) ++#define WARN(dev,fmt,args...) \ ++ xprintk(dev , KERN_WARNING , fmt , ## args) ++#define INFO(dev,fmt,args...) \ ++ xprintk(dev , KERN_INFO , fmt , ## args) ++ ++/*-------------------------------------------------------------------------*/ ++ ++static unsigned buflen = 4096; ++static unsigned qlen = 32; ++static unsigned pattern = 0; ++ ++module_param (buflen, uint, S_IRUGO|S_IWUSR); ++module_param (qlen, uint, S_IRUGO|S_IWUSR); ++module_param (pattern, uint, S_IRUGO|S_IWUSR); ++ ++/* ++ * if it's nonzero, autoresume says how many seconds to wait ++ * before trying to wake up the host after suspend. ++ */ ++static unsigned autoresume = 0; ++module_param (autoresume, uint, 0); ++ ++/* ++ * Normally the "loopback" configuration is second (index 1) so ++ * it's not the default. Here's where to change that order, to ++ * work better with hosts where config changes are problematic. ++ * Or controllers (like superh) that only support one config. ++ */ ++static int loopdefault = 0; ++ ++module_param (loopdefault, bool, S_IRUGO|S_IWUSR); ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* Thanks to NetChip Technologies for donating this product ID. ++ * ++ * DO NOT REUSE THESE IDs with a protocol-incompatible driver!! Ever!! ++ * Instead: allocate your own, using normal USB-IF procedures. ++ */ ++#ifndef CONFIG_USB_ZERO_HNPTEST ++#define DRIVER_VENDOR_NUM 0x0525 /* NetChip */ ++#define DRIVER_PRODUCT_NUM 0xa4a0 /* Linux-USB "Gadget Zero" */ ++#else ++#define DRIVER_VENDOR_NUM 0x1a0a /* OTG test device IDs */ ++#define DRIVER_PRODUCT_NUM 0xbadd ++#endif ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* ++ * DESCRIPTORS ... most are static, but strings and (full) ++ * configuration descriptors are built on demand. ++ */ ++ ++/* ++#define STRING_MANUFACTURER 25 ++#define STRING_PRODUCT 42 ++#define STRING_SERIAL 101 ++*/ ++#define STRING_MANUFACTURER 1 ++#define STRING_PRODUCT 2 ++#define STRING_SERIAL 3 ++ ++#define STRING_SOURCE_SINK 250 ++#define STRING_LOOPBACK 251 ++ ++/* ++ * This device advertises two configurations; these numbers work ++ * on a pxa250 as well as more flexible hardware. ++ */ ++#define CONFIG_SOURCE_SINK 3 ++#define CONFIG_LOOPBACK 2 ++ ++/* ++static struct usb_device_descriptor ++device_desc = { ++ .bLength = sizeof device_desc, ++ .bDescriptorType = USB_DT_DEVICE, ++ ++ .bcdUSB = __constant_cpu_to_le16 (0x0200), ++ .bDeviceClass = USB_CLASS_VENDOR_SPEC, ++ ++ .idVendor = __constant_cpu_to_le16 (DRIVER_VENDOR_NUM), ++ .idProduct = __constant_cpu_to_le16 (DRIVER_PRODUCT_NUM), ++ .iManufacturer = STRING_MANUFACTURER, ++ .iProduct = STRING_PRODUCT, ++ .iSerialNumber = STRING_SERIAL, ++ .bNumConfigurations = 2, ++}; ++*/ ++static struct usb_device_descriptor ++device_desc = { ++ .bLength = sizeof device_desc, ++ .bDescriptorType = USB_DT_DEVICE, ++ .bcdUSB = __constant_cpu_to_le16 (0x0100), ++ .bDeviceClass = USB_CLASS_PER_INTERFACE, ++ .bDeviceSubClass = 0, ++ .bDeviceProtocol = 0, ++ .bMaxPacketSize0 = 64, ++ .bcdDevice = __constant_cpu_to_le16 (0x0100), ++ .idVendor = __constant_cpu_to_le16 (0x0499), ++ .idProduct = __constant_cpu_to_le16 (0x3002), ++ .iManufacturer = STRING_MANUFACTURER, ++ .iProduct = STRING_PRODUCT, ++ .iSerialNumber = STRING_SERIAL, ++ .bNumConfigurations = 1, ++}; ++ ++static struct usb_config_descriptor ++z_config = { ++ .bLength = sizeof z_config, ++ .bDescriptorType = USB_DT_CONFIG, ++ ++ /* compute wTotalLength on the fly */ ++ .bNumInterfaces = 2, ++ .bConfigurationValue = 1, ++ .iConfiguration = 0, ++ .bmAttributes = 0x40, ++ .bMaxPower = 0, /* self-powered */ ++}; ++ ++ ++static struct usb_otg_descriptor ++otg_descriptor = { ++ .bLength = sizeof otg_descriptor, ++ .bDescriptorType = USB_DT_OTG, ++ ++ .bmAttributes = USB_OTG_SRP, ++}; ++ ++/* one interface in each configuration */ ++#ifdef CONFIG_USB_GADGET_DUALSPEED ++ ++/* ++ * usb 2.0 devices need to expose both high speed and full speed ++ * descriptors, unless they only run at full speed. ++ * ++ * that means alternate endpoint descriptors (bigger packets) ++ * and a "device qualifier" ... plus more construction options ++ * for the config descriptor. ++ */ ++ ++static struct usb_qualifier_descriptor ++dev_qualifier = { ++ .bLength = sizeof dev_qualifier, ++ .bDescriptorType = USB_DT_DEVICE_QUALIFIER, ++ ++ .bcdUSB = __constant_cpu_to_le16 (0x0200), ++ .bDeviceClass = USB_CLASS_VENDOR_SPEC, ++ ++ .bNumConfigurations = 2, ++}; ++ ++ ++struct usb_cs_as_general_descriptor { ++ __u8 bLength; ++ __u8 bDescriptorType; ++ ++ __u8 bDescriptorSubType; ++ __u8 bTerminalLink; ++ __u8 bDelay; ++ __u16 wFormatTag; ++} __attribute__ ((packed)); ++ ++struct usb_cs_as_format_descriptor { ++ __u8 bLength; ++ __u8 bDescriptorType; ++ ++ __u8 bDescriptorSubType; ++ __u8 bFormatType; ++ __u8 bNrChannels; ++ __u8 bSubframeSize; ++ __u8 bBitResolution; ++ __u8 bSamfreqType; ++ __u8 tLowerSamFreq[3]; ++ __u8 tUpperSamFreq[3]; ++} __attribute__ ((packed)); ++ ++static const struct usb_interface_descriptor ++z_audio_control_if_desc = { ++ .bLength = sizeof z_audio_control_if_desc, ++ .bDescriptorType = USB_DT_INTERFACE, ++ .bInterfaceNumber = 0, ++ .bAlternateSetting = 0, ++ .bNumEndpoints = 0, ++ .bInterfaceClass = USB_CLASS_AUDIO, ++ .bInterfaceSubClass = 0x1, ++ .bInterfaceProtocol = 0, ++ .iInterface = 0, ++}; ++ ++static const struct usb_interface_descriptor ++z_audio_if_desc = { ++ .bLength = sizeof z_audio_if_desc, ++ .bDescriptorType = USB_DT_INTERFACE, ++ .bInterfaceNumber = 1, ++ .bAlternateSetting = 0, ++ .bNumEndpoints = 0, ++ .bInterfaceClass = USB_CLASS_AUDIO, ++ .bInterfaceSubClass = 0x2, ++ .bInterfaceProtocol = 0, ++ .iInterface = 0, ++}; ++ ++static const struct usb_interface_descriptor ++z_audio_if_desc2 = { ++ .bLength = sizeof z_audio_if_desc, ++ .bDescriptorType = USB_DT_INTERFACE, ++ .bInterfaceNumber = 1, ++ .bAlternateSetting = 1, ++ .bNumEndpoints = 1, ++ .bInterfaceClass = USB_CLASS_AUDIO, ++ .bInterfaceSubClass = 0x2, ++ .bInterfaceProtocol = 0, ++ .iInterface = 0, ++}; ++ ++static const struct usb_cs_as_general_descriptor ++z_audio_cs_as_if_desc = { ++ .bLength = 7, ++ .bDescriptorType = 0x24, ++ ++ .bDescriptorSubType = 0x01, ++ .bTerminalLink = 0x01, ++ .bDelay = 0x0, ++ .wFormatTag = __constant_cpu_to_le16 (0x0001) ++}; ++ ++ ++static const struct usb_cs_as_format_descriptor ++z_audio_cs_as_format_desc = { ++ .bLength = 0xe, ++ .bDescriptorType = 0x24, ++ ++ .bDescriptorSubType = 2, ++ .bFormatType = 1, ++ .bNrChannels = 1, ++ .bSubframeSize = 1, ++ .bBitResolution = 8, ++ .bSamfreqType = 0, ++ .tLowerSamFreq = {0x7e, 0x13, 0x00}, ++ .tUpperSamFreq = {0xe2, 0xd6, 0x00}, ++}; ++ ++static const struct usb_endpoint_descriptor ++z_iso_ep = { ++ .bLength = 0x09, ++ .bDescriptorType = 0x05, ++ .bEndpointAddress = 0x04, ++ .bmAttributes = 0x09, ++ .wMaxPacketSize = 0x0038, ++ .bInterval = 0x01, ++ .bRefresh = 0x00, ++ .bSynchAddress = 0x00, ++}; ++ ++static char z_iso_ep2[] = {0x07, 0x25, 0x01, 0x00, 0x02, 0x00, 0x02}; ++ ++// 9 bytes ++static char z_ac_interface_header_desc[] = ++{ 0x09, 0x24, 0x01, 0x00, 0x01, 0x2b, 0x00, 0x01, 0x01 }; ++ ++// 12 bytes ++static char z_0[] = {0x0c, 0x24, 0x02, 0x01, 0x01, 0x01, 0x00, 0x02, ++ 0x03, 0x00, 0x00, 0x00}; ++// 13 bytes ++static char z_1[] = {0x0d, 0x24, 0x06, 0x02, 0x01, 0x02, 0x15, 0x00, ++ 0x02, 0x00, 0x02, 0x00, 0x00}; ++// 9 bytes ++static char z_2[] = {0x09, 0x24, 0x03, 0x03, 0x01, 0x03, 0x00, 0x02, ++ 0x00}; ++ ++static char za_0[] = {0x09, 0x04, 0x01, 0x02, 0x01, 0x01, 0x02, 0x00, ++ 0x00}; ++ ++static char za_1[] = {0x07, 0x24, 0x01, 0x01, 0x00, 0x01, 0x00}; ++ ++static char za_2[] = {0x0e, 0x24, 0x02, 0x01, 0x02, 0x01, 0x08, 0x00, ++ 0x7e, 0x13, 0x00, 0xe2, 0xd6, 0x00}; ++ ++static char za_3[] = {0x09, 0x05, 0x04, 0x09, 0x70, 0x00, 0x01, 0x00, ++ 0x00}; ++ ++static char za_4[] = {0x07, 0x25, 0x01, 0x00, 0x02, 0x00, 0x02}; ++ ++static char za_5[] = {0x09, 0x04, 0x01, 0x03, 0x01, 0x01, 0x02, 0x00, ++ 0x00}; ++ ++static char za_6[] = {0x07, 0x24, 0x01, 0x01, 0x00, 0x01, 0x00}; ++ ++static char za_7[] = {0x0e, 0x24, 0x02, 0x01, 0x01, 0x02, 0x10, 0x00, ++ 0x7e, 0x13, 0x00, 0xe2, 0xd6, 0x00}; ++ ++static char za_8[] = {0x09, 0x05, 0x04, 0x09, 0x70, 0x00, 0x01, 0x00, ++ 0x00}; ++ ++static char za_9[] = {0x07, 0x25, 0x01, 0x00, 0x02, 0x00, 0x02}; ++ ++static char za_10[] = {0x09, 0x04, 0x01, 0x04, 0x01, 0x01, 0x02, 0x00, ++ 0x00}; ++ ++static char za_11[] = {0x07, 0x24, 0x01, 0x01, 0x00, 0x01, 0x00}; ++ ++static char za_12[] = {0x0e, 0x24, 0x02, 0x01, 0x02, 0x02, 0x10, 0x00, ++ 0x73, 0x13, 0x00, 0xe2, 0xd6, 0x00}; ++ ++static char za_13[] = {0x09, 0x05, 0x04, 0x09, 0xe0, 0x00, 0x01, 0x00, ++ 0x00}; ++ ++static char za_14[] = {0x07, 0x25, 0x01, 0x00, 0x02, 0x00, 0x02}; ++ ++static char za_15[] = {0x09, 0x04, 0x01, 0x05, 0x01, 0x01, 0x02, 0x00, ++ 0x00}; ++ ++static char za_16[] = {0x07, 0x24, 0x01, 0x01, 0x00, 0x01, 0x00}; ++ ++static char za_17[] = {0x0e, 0x24, 0x02, 0x01, 0x01, 0x03, 0x14, 0x00, ++ 0x7e, 0x13, 0x00, 0xe2, 0xd6, 0x00}; ++ ++static char za_18[] = {0x09, 0x05, 0x04, 0x09, 0xa8, 0x00, 0x01, 0x00, ++ 0x00}; ++ ++static char za_19[] = {0x07, 0x25, 0x01, 0x00, 0x02, 0x00, 0x02}; ++ ++static char za_20[] = {0x09, 0x04, 0x01, 0x06, 0x01, 0x01, 0x02, 0x00, ++ 0x00}; ++ ++static char za_21[] = {0x07, 0x24, 0x01, 0x01, 0x00, 0x01, 0x00}; ++ ++static char za_22[] = {0x0e, 0x24, 0x02, 0x01, 0x02, 0x03, 0x14, 0x00, ++ 0x7e, 0x13, 0x00, 0xe2, 0xd6, 0x00}; ++ ++static char za_23[] = {0x09, 0x05, 0x04, 0x09, 0x50, 0x01, 0x01, 0x00, ++ 0x00}; ++ ++static char za_24[] = {0x07, 0x25, 0x01, 0x00, 0x02, 0x00, 0x02}; ++ ++ ++ ++static const struct usb_descriptor_header *z_function [] = { ++ (struct usb_descriptor_header *) &z_audio_control_if_desc, ++ (struct usb_descriptor_header *) &z_ac_interface_header_desc, ++ (struct usb_descriptor_header *) &z_0, ++ (struct usb_descriptor_header *) &z_1, ++ (struct usb_descriptor_header *) &z_2, ++ (struct usb_descriptor_header *) &z_audio_if_desc, ++ (struct usb_descriptor_header *) &z_audio_if_desc2, ++ (struct usb_descriptor_header *) &z_audio_cs_as_if_desc, ++ (struct usb_descriptor_header *) &z_audio_cs_as_format_desc, ++ (struct usb_descriptor_header *) &z_iso_ep, ++ (struct usb_descriptor_header *) &z_iso_ep2, ++ (struct usb_descriptor_header *) &za_0, ++ (struct usb_descriptor_header *) &za_1, ++ (struct usb_descriptor_header *) &za_2, ++ (struct usb_descriptor_header *) &za_3, ++ (struct usb_descriptor_header *) &za_4, ++ (struct usb_descriptor_header *) &za_5, ++ (struct usb_descriptor_header *) &za_6, ++ (struct usb_descriptor_header *) &za_7, ++ (struct usb_descriptor_header *) &za_8, ++ (struct usb_descriptor_header *) &za_9, ++ (struct usb_descriptor_header *) &za_10, ++ (struct usb_descriptor_header *) &za_11, ++ (struct usb_descriptor_header *) &za_12, ++ (struct usb_descriptor_header *) &za_13, ++ (struct usb_descriptor_header *) &za_14, ++ (struct usb_descriptor_header *) &za_15, ++ (struct usb_descriptor_header *) &za_16, ++ (struct usb_descriptor_header *) &za_17, ++ (struct usb_descriptor_header *) &za_18, ++ (struct usb_descriptor_header *) &za_19, ++ (struct usb_descriptor_header *) &za_20, ++ (struct usb_descriptor_header *) &za_21, ++ (struct usb_descriptor_header *) &za_22, ++ (struct usb_descriptor_header *) &za_23, ++ (struct usb_descriptor_header *) &za_24, ++ NULL, ++}; ++ ++/* maxpacket and other transfer characteristics vary by speed. */ ++#define ep_desc(g,hs,fs) (((g)->speed==USB_SPEED_HIGH)?(hs):(fs)) ++ ++#else ++ ++/* if there's no high speed support, maxpacket doesn't change. */ ++#define ep_desc(g,hs,fs) fs ++ ++#endif /* !CONFIG_USB_GADGET_DUALSPEED */ ++ ++static char manufacturer [40]; ++//static char serial [40]; ++static char serial [] = "Ser 00 em"; ++ ++/* static strings, in UTF-8 */ ++static struct usb_string strings [] = { ++ { STRING_MANUFACTURER, manufacturer, }, ++ { STRING_PRODUCT, longname, }, ++ { STRING_SERIAL, serial, }, ++ { STRING_LOOPBACK, loopback, }, ++ { STRING_SOURCE_SINK, source_sink, }, ++ { } /* end of list */ ++}; ++ ++static struct usb_gadget_strings stringtab = { ++ .language = 0x0409, /* en-us */ ++ .strings = strings, ++}; ++ ++/* ++ * config descriptors are also handcrafted. these must agree with code ++ * that sets configurations, and with code managing interfaces and their ++ * altsettings. other complexity may come from: ++ * ++ * - high speed support, including "other speed config" rules ++ * - multiple configurations ++ * - interfaces with alternate settings ++ * - embedded class or vendor-specific descriptors ++ * ++ * this handles high speed, and has a second config that could as easily ++ * have been an alternate interface setting (on most hardware). ++ * ++ * NOTE: to demonstrate (and test) more USB capabilities, this driver ++ * should include an altsetting to test interrupt transfers, including ++ * high bandwidth modes at high speed. (Maybe work like Intel's test ++ * device?) ++ */ ++static int ++config_buf (struct usb_gadget *gadget, u8 *buf, u8 type, unsigned index) ++{ ++ int len; ++ const struct usb_descriptor_header **function; ++ ++ function = z_function; ++ len = usb_gadget_config_buf (&z_config, buf, USB_BUFSIZ, function); ++ if (len < 0) ++ return len; ++ ((struct usb_config_descriptor *) buf)->bDescriptorType = type; ++ return len; ++} ++ ++/*-------------------------------------------------------------------------*/ ++ ++static struct usb_request * ++alloc_ep_req (struct usb_ep *ep, unsigned length) ++{ ++ struct usb_request *req; ++ ++ req = usb_ep_alloc_request (ep, GFP_ATOMIC); ++ if (req) { ++ req->length = length; ++ req->buf = usb_ep_alloc_buffer (ep, length, ++ &req->dma, GFP_ATOMIC); ++ if (!req->buf) { ++ usb_ep_free_request (ep, req); ++ req = NULL; ++ } ++ } ++ return req; ++} ++ ++static void free_ep_req (struct usb_ep *ep, struct usb_request *req) ++{ ++ if (req->buf) ++ usb_ep_free_buffer (ep, req->buf, req->dma, req->length); ++ usb_ep_free_request (ep, req); ++} ++ ++/*-------------------------------------------------------------------------*/ ++ ++/* optionally require specific source/sink data patterns */ ++ ++static int ++check_read_data ( ++ struct zero_dev *dev, ++ struct usb_ep *ep, ++ struct usb_request *req ++) ++{ ++ unsigned i; ++ u8 *buf = req->buf; ++ ++ for (i = 0; i < req->actual; i++, buf++) { ++ switch (pattern) { ++ /* all-zeroes has no synchronization issues */ ++ case 0: ++ if (*buf == 0) ++ continue; ++ break; ++ /* mod63 stays in sync with short-terminated transfers, ++ * or otherwise when host and gadget agree on how large ++ * each usb transfer request should be. resync is done ++ * with set_interface or set_config. ++ */ ++ case 1: ++ if (*buf == (u8)(i % 63)) ++ continue; ++ break; ++ } ++ ERROR (dev, "bad OUT byte, buf [%d] = %d\n", i, *buf); ++ usb_ep_set_halt (ep); ++ return -EINVAL; ++ } ++ return 0; ++} ++ ++/*-------------------------------------------------------------------------*/ ++ ++static void zero_reset_config (struct zero_dev *dev) ++{ ++ if (dev->config == 0) ++ return; ++ ++ DBG (dev, "reset config\n"); ++ ++ /* just disable endpoints, forcing completion of pending i/o. ++ * all our completion handlers free their requests in this case. ++ */ ++ if (dev->in_ep) { ++ usb_ep_disable (dev->in_ep); ++ dev->in_ep = NULL; ++ } ++ if (dev->out_ep) { ++ usb_ep_disable (dev->out_ep); ++ dev->out_ep = NULL; ++ } ++ dev->config = 0; ++ del_timer (&dev->resume); ++} ++ ++#define _write(f, buf, sz) (f->f_op->write(f, buf, sz, &f->f_pos)) ++ ++static void ++zero_isoc_complete (struct usb_ep *ep, struct usb_request *req) ++{ ++ struct zero_dev *dev = ep->driver_data; ++ int status = req->status; ++ int i, j; ++ ++ switch (status) { ++ ++ case 0: /* normal completion? */ ++ //printk ("\nzero ---------------> isoc normal completion %d bytes\n", req->actual); ++ for (i=0, j=rbuf_start; iactual; i++) { ++ //printk ("%02x ", ((__u8*)req->buf)[i]); ++ rbuf[j] = ((__u8*)req->buf)[i]; ++ j++; ++ if (j >= RBUF_LEN) j=0; ++ } ++ rbuf_start = j; ++ //printk ("\n\n"); ++ ++ if (rbuf_len < RBUF_LEN) { ++ rbuf_len += req->actual; ++ if (rbuf_len > RBUF_LEN) { ++ rbuf_len = RBUF_LEN; ++ } ++ } ++ ++ break; ++ ++ /* this endpoint is normally active while we're configured */ ++ case -ECONNABORTED: /* hardware forced ep reset */ ++ case -ECONNRESET: /* request dequeued */ ++ case -ESHUTDOWN: /* disconnect from host */ ++ VDBG (dev, "%s gone (%d), %d/%d\n", ep->name, status, ++ req->actual, req->length); ++ if (ep == dev->out_ep) ++ check_read_data (dev, ep, req); ++ free_ep_req (ep, req); ++ return; ++ ++ case -EOVERFLOW: /* buffer overrun on read means that ++ * we didn't provide a big enough ++ * buffer. ++ */ ++ default: ++#if 1 ++ DBG (dev, "%s complete --> %d, %d/%d\n", ep->name, ++ status, req->actual, req->length); ++#endif ++ case -EREMOTEIO: /* short read */ ++ break; ++ } ++ ++ status = usb_ep_queue (ep, req, GFP_ATOMIC); ++ if (status) { ++ ERROR (dev, "kill %s: resubmit %d bytes --> %d\n", ++ ep->name, req->length, status); ++ usb_ep_set_halt (ep); ++ /* FIXME recover later ... somehow */ ++ } ++} ++ ++static struct usb_request * ++zero_start_isoc_ep (struct usb_ep *ep, int gfp_flags) ++{ ++ struct usb_request *req; ++ int status; ++ ++ req = alloc_ep_req (ep, 512); ++ if (!req) ++ return NULL; ++ ++ req->complete = zero_isoc_complete; ++ ++ status = usb_ep_queue (ep, req, gfp_flags); ++ if (status) { ++ struct zero_dev *dev = ep->driver_data; ++ ++ ERROR (dev, "start %s --> %d\n", ep->name, status); ++ free_ep_req (ep, req); ++ req = NULL; ++ } ++ ++ return req; ++} ++ ++/* change our operational config. this code must agree with the code ++ * that returns config descriptors, and altsetting code. ++ * ++ * it's also responsible for power management interactions. some ++ * configurations might not work with our current power sources. ++ * ++ * note that some device controller hardware will constrain what this ++ * code can do, perhaps by disallowing more than one configuration or ++ * by limiting configuration choices (like the pxa2xx). ++ */ ++static int ++zero_set_config (struct zero_dev *dev, unsigned number, int gfp_flags) ++{ ++ int result = 0; ++ struct usb_gadget *gadget = dev->gadget; ++ const struct usb_endpoint_descriptor *d; ++ struct usb_ep *ep; ++ ++ if (number == dev->config) ++ return 0; ++ ++ zero_reset_config (dev); ++ ++ gadget_for_each_ep (ep, gadget) { ++ ++ if (strcmp (ep->name, "ep4") == 0) { ++ ++ d = (struct usb_endpoint_descripter *)&za_23; // isoc ep desc for audio i/f alt setting 6 ++ result = usb_ep_enable (ep, d); ++ ++ if (result == 0) { ++ ep->driver_data = dev; ++ dev->in_ep = ep; ++ ++ if (zero_start_isoc_ep (ep, gfp_flags) != 0) { ++ ++ dev->in_ep = ep; ++ continue; ++ } ++ ++ usb_ep_disable (ep); ++ result = -EIO; ++ } ++ } ++ ++ } ++ ++ dev->config = number; ++ return result; ++} ++ ++/*-------------------------------------------------------------------------*/ ++ ++static void zero_setup_complete (struct usb_ep *ep, struct usb_request *req) ++{ ++ if (req->status || req->actual != req->length) ++ DBG ((struct zero_dev *) ep->driver_data, ++ "setup complete --> %d, %d/%d\n", ++ req->status, req->actual, req->length); ++} ++ ++/* ++ * The setup() callback implements all the ep0 functionality that's ++ * not handled lower down, in hardware or the hardware driver (like ++ * device and endpoint feature flags, and their status). It's all ++ * housekeeping for the gadget function we're implementing. Most of ++ * the work is in config-specific setup. ++ */ ++static int ++zero_setup (struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl) ++{ ++ struct zero_dev *dev = get_gadget_data (gadget); ++ struct usb_request *req = dev->req; ++ int value = -EOPNOTSUPP; ++ ++ /* usually this stores reply data in the pre-allocated ep0 buffer, ++ * but config change events will reconfigure hardware. ++ */ ++ req->zero = 0; ++ switch (ctrl->bRequest) { ++ ++ case USB_REQ_GET_DESCRIPTOR: ++ ++ switch (ctrl->wValue >> 8) { ++ ++ case USB_DT_DEVICE: ++ value = min (ctrl->wLength, (u16) sizeof device_desc); ++ memcpy (req->buf, &device_desc, value); ++ break; ++#ifdef CONFIG_USB_GADGET_DUALSPEED ++ case USB_DT_DEVICE_QUALIFIER: ++ if (!gadget->is_dualspeed) ++ break; ++ value = min (ctrl->wLength, (u16) sizeof dev_qualifier); ++ memcpy (req->buf, &dev_qualifier, value); ++ break; ++ ++ case USB_DT_OTHER_SPEED_CONFIG: ++ if (!gadget->is_dualspeed) ++ break; ++ // FALLTHROUGH ++#endif /* CONFIG_USB_GADGET_DUALSPEED */ ++ case USB_DT_CONFIG: ++ value = config_buf (gadget, req->buf, ++ ctrl->wValue >> 8, ++ ctrl->wValue & 0xff); ++ if (value >= 0) ++ value = min (ctrl->wLength, (u16) value); ++ break; ++ ++ case USB_DT_STRING: ++ /* wIndex == language code. ++ * this driver only handles one language, you can ++ * add string tables for other languages, using ++ * any UTF-8 characters ++ */ ++ value = usb_gadget_get_string (&stringtab, ++ ctrl->wValue & 0xff, req->buf); ++ if (value >= 0) { ++ value = min (ctrl->wLength, (u16) value); ++ } ++ break; ++ } ++ break; ++ ++ /* currently two configs, two speeds */ ++ case USB_REQ_SET_CONFIGURATION: ++ if (ctrl->bRequestType != 0) ++ goto unknown; ++ ++ spin_lock (&dev->lock); ++ value = zero_set_config (dev, ctrl->wValue, GFP_ATOMIC); ++ spin_unlock (&dev->lock); ++ break; ++ case USB_REQ_GET_CONFIGURATION: ++ if (ctrl->bRequestType != USB_DIR_IN) ++ goto unknown; ++ *(u8 *)req->buf = dev->config; ++ value = min (ctrl->wLength, (u16) 1); ++ break; ++ ++ /* until we add altsetting support, or other interfaces, ++ * only 0/0 are possible. pxa2xx only supports 0/0 (poorly) ++ * and already killed pending endpoint I/O. ++ */ ++ case USB_REQ_SET_INTERFACE: ++ ++ if (ctrl->bRequestType != USB_RECIP_INTERFACE) ++ goto unknown; ++ spin_lock (&dev->lock); ++ if (dev->config) { ++ u8 config = dev->config; ++ ++ /* resets interface configuration, forgets about ++ * previous transaction state (queued bufs, etc) ++ * and re-inits endpoint state (toggle etc) ++ * no response queued, just zero status == success. ++ * if we had more than one interface we couldn't ++ * use this "reset the config" shortcut. ++ */ ++ zero_reset_config (dev); ++ zero_set_config (dev, config, GFP_ATOMIC); ++ value = 0; ++ } ++ spin_unlock (&dev->lock); ++ break; ++ case USB_REQ_GET_INTERFACE: ++ if ((ctrl->bRequestType == 0x21) && (ctrl->wIndex == 0x02)) { ++ value = ctrl->wLength; ++ break; ++ } ++ else { ++ if (ctrl->bRequestType != (USB_DIR_IN|USB_RECIP_INTERFACE)) ++ goto unknown; ++ if (!dev->config) ++ break; ++ if (ctrl->wIndex != 0) { ++ value = -EDOM; ++ break; ++ } ++ *(u8 *)req->buf = 0; ++ value = min (ctrl->wLength, (u16) 1); ++ } ++ break; ++ ++ /* ++ * These are the same vendor-specific requests supported by ++ * Intel's USB 2.0 compliance test devices. We exceed that ++ * device spec by allowing multiple-packet requests. ++ */ ++ case 0x5b: /* control WRITE test -- fill the buffer */ ++ if (ctrl->bRequestType != (USB_DIR_OUT|USB_TYPE_VENDOR)) ++ goto unknown; ++ if (ctrl->wValue || ctrl->wIndex) ++ break; ++ /* just read that many bytes into the buffer */ ++ if (ctrl->wLength > USB_BUFSIZ) ++ break; ++ value = ctrl->wLength; ++ break; ++ case 0x5c: /* control READ test -- return the buffer */ ++ if (ctrl->bRequestType != (USB_DIR_IN|USB_TYPE_VENDOR)) ++ goto unknown; ++ if (ctrl->wValue || ctrl->wIndex) ++ break; ++ /* expect those bytes are still in the buffer; send back */ ++ if (ctrl->wLength > USB_BUFSIZ ++ || ctrl->wLength != req->length) ++ break; ++ value = ctrl->wLength; ++ break; ++ ++ case 0x01: // SET_CUR ++ case 0x02: ++ case 0x03: ++ case 0x04: ++ case 0x05: ++ value = ctrl->wLength; ++ break; ++ case 0x81: ++ switch (ctrl->wValue) { ++ case 0x0201: ++ case 0x0202: ++ ((u8*)req->buf)[0] = 0x00; ++ ((u8*)req->buf)[1] = 0xe3; ++ break; ++ case 0x0300: ++ case 0x0500: ++ ((u8*)req->buf)[0] = 0x00; ++ break; ++ } ++ //((u8*)req->buf)[0] = 0x81; ++ //((u8*)req->buf)[1] = 0x81; ++ value = ctrl->wLength; ++ break; ++ case 0x82: ++ switch (ctrl->wValue) { ++ case 0x0201: ++ case 0x0202: ++ ((u8*)req->buf)[0] = 0x00; ++ ((u8*)req->buf)[1] = 0xc3; ++ break; ++ case 0x0300: ++ case 0x0500: ++ ((u8*)req->buf)[0] = 0x00; ++ break; ++ } ++ //((u8*)req->buf)[0] = 0x82; ++ //((u8*)req->buf)[1] = 0x82; ++ value = ctrl->wLength; ++ break; ++ case 0x83: ++ switch (ctrl->wValue) { ++ case 0x0201: ++ case 0x0202: ++ ((u8*)req->buf)[0] = 0x00; ++ ((u8*)req->buf)[1] = 0x00; ++ break; ++ case 0x0300: ++ ((u8*)req->buf)[0] = 0x60; ++ break; ++ case 0x0500: ++ ((u8*)req->buf)[0] = 0x18; ++ break; ++ } ++ //((u8*)req->buf)[0] = 0x83; ++ //((u8*)req->buf)[1] = 0x83; ++ value = ctrl->wLength; ++ break; ++ case 0x84: ++ switch (ctrl->wValue) { ++ case 0x0201: ++ case 0x0202: ++ ((u8*)req->buf)[0] = 0x00; ++ ((u8*)req->buf)[1] = 0x01; ++ break; ++ case 0x0300: ++ case 0x0500: ++ ((u8*)req->buf)[0] = 0x08; ++ break; ++ } ++ //((u8*)req->buf)[0] = 0x84; ++ //((u8*)req->buf)[1] = 0x84; ++ value = ctrl->wLength; ++ break; ++ case 0x85: ++ ((u8*)req->buf)[0] = 0x85; ++ ((u8*)req->buf)[1] = 0x85; ++ value = ctrl->wLength; ++ break; ++ ++ ++ default: ++unknown: ++ printk("unknown control req%02x.%02x v%04x i%04x l%d\n", ++ ctrl->bRequestType, ctrl->bRequest, ++ ctrl->wValue, ctrl->wIndex, ctrl->wLength); ++ } ++ ++ /* respond with data transfer before status phase? */ ++ if (value >= 0) { ++ req->length = value; ++ req->zero = value < ctrl->wLength ++ && (value % gadget->ep0->maxpacket) == 0; ++ value = usb_ep_queue (gadget->ep0, req, GFP_ATOMIC); ++ if (value < 0) { ++ DBG (dev, "ep_queue < 0 --> %d\n", value); ++ req->status = 0; ++ zero_setup_complete (gadget->ep0, req); ++ } ++ } ++ ++ /* device either stalls (value < 0) or reports success */ ++ return value; ++} ++ ++static void ++zero_disconnect (struct usb_gadget *gadget) ++{ ++ struct zero_dev *dev = get_gadget_data (gadget); ++ unsigned long flags; ++ ++ spin_lock_irqsave (&dev->lock, flags); ++ zero_reset_config (dev); ++ ++ /* a more significant application might have some non-usb ++ * activities to quiesce here, saving resources like power ++ * or pushing the notification up a network stack. ++ */ ++ spin_unlock_irqrestore (&dev->lock, flags); ++ ++ /* next we may get setup() calls to enumerate new connections; ++ * or an unbind() during shutdown (including removing module). ++ */ ++} ++ ++static void ++zero_autoresume (unsigned long _dev) ++{ ++ struct zero_dev *dev = (struct zero_dev *) _dev; ++ int status; ++ ++ /* normally the host would be woken up for something ++ * more significant than just a timer firing... ++ */ ++ if (dev->gadget->speed != USB_SPEED_UNKNOWN) { ++ status = usb_gadget_wakeup (dev->gadget); ++ DBG (dev, "wakeup --> %d\n", status); ++ } ++} ++ ++/*-------------------------------------------------------------------------*/ ++ ++static void ++zero_unbind (struct usb_gadget *gadget) ++{ ++ struct zero_dev *dev = get_gadget_data (gadget); ++ ++ DBG (dev, "unbind\n"); ++ ++ /* we've already been disconnected ... no i/o is active */ ++ if (dev->req) ++ free_ep_req (gadget->ep0, dev->req); ++ del_timer_sync (&dev->resume); ++ kfree (dev); ++ set_gadget_data (gadget, NULL); ++} ++ ++static int ++zero_bind (struct usb_gadget *gadget) ++{ ++ struct zero_dev *dev; ++ //struct usb_ep *ep; ++ ++ printk("binding\n"); ++ /* ++ * DRIVER POLICY CHOICE: you may want to do this differently. ++ * One thing to avoid is reusing a bcdDevice revision code ++ * with different host-visible configurations or behavior ++ * restrictions -- using ep1in/ep2out vs ep1out/ep3in, etc ++ */ ++ //device_desc.bcdDevice = __constant_cpu_to_le16 (0x0201); ++ ++ ++ /* ok, we made sense of the hardware ... */ ++ dev = kzalloc (sizeof *dev, SLAB_KERNEL); ++ if (!dev) ++ return -ENOMEM; ++ spin_lock_init (&dev->lock); ++ dev->gadget = gadget; ++ set_gadget_data (gadget, dev); ++ ++ /* preallocate control response and buffer */ ++ dev->req = usb_ep_alloc_request (gadget->ep0, GFP_KERNEL); ++ if (!dev->req) ++ goto enomem; ++ dev->req->buf = usb_ep_alloc_buffer (gadget->ep0, USB_BUFSIZ, ++ &dev->req->dma, GFP_KERNEL); ++ if (!dev->req->buf) ++ goto enomem; ++ ++ dev->req->complete = zero_setup_complete; ++ ++ device_desc.bMaxPacketSize0 = gadget->ep0->maxpacket; ++ ++#ifdef CONFIG_USB_GADGET_DUALSPEED ++ /* assume ep0 uses the same value for both speeds ... */ ++ dev_qualifier.bMaxPacketSize0 = device_desc.bMaxPacketSize0; ++ ++ /* and that all endpoints are dual-speed */ ++ //hs_source_desc.bEndpointAddress = fs_source_desc.bEndpointAddress; ++ //hs_sink_desc.bEndpointAddress = fs_sink_desc.bEndpointAddress; ++#endif ++ ++ usb_gadget_set_selfpowered (gadget); ++ ++ init_timer (&dev->resume); ++ dev->resume.function = zero_autoresume; ++ dev->resume.data = (unsigned long) dev; ++ ++ gadget->ep0->driver_data = dev; ++ ++ INFO (dev, "%s, version: " DRIVER_VERSION "\n", longname); ++ INFO (dev, "using %s, OUT %s IN %s\n", gadget->name, ++ EP_OUT_NAME, EP_IN_NAME); ++ ++ snprintf (manufacturer, sizeof manufacturer, ++ UTS_SYSNAME " " UTS_RELEASE " with %s", ++ gadget->name); ++ ++ return 0; ++ ++enomem: ++ zero_unbind (gadget); ++ return -ENOMEM; ++} ++ ++/*-------------------------------------------------------------------------*/ ++ ++static void ++zero_suspend (struct usb_gadget *gadget) ++{ ++ struct zero_dev *dev = get_gadget_data (gadget); ++ ++ if (gadget->speed == USB_SPEED_UNKNOWN) ++ return; ++ ++ if (autoresume) { ++ mod_timer (&dev->resume, jiffies + (HZ * autoresume)); ++ DBG (dev, "suspend, wakeup in %d seconds\n", autoresume); ++ } else ++ DBG (dev, "suspend\n"); ++} ++ ++static void ++zero_resume (struct usb_gadget *gadget) ++{ ++ struct zero_dev *dev = get_gadget_data (gadget); ++ ++ DBG (dev, "resume\n"); ++ del_timer (&dev->resume); ++} ++ ++ ++/*-------------------------------------------------------------------------*/ ++ ++static struct usb_gadget_driver zero_driver = { ++#ifdef CONFIG_USB_GADGET_DUALSPEED ++ .speed = USB_SPEED_HIGH, ++#else ++ .speed = USB_SPEED_FULL, ++#endif ++ .function = (char *) longname, ++ .bind = zero_bind, ++ .unbind = zero_unbind, ++ ++ .setup = zero_setup, ++ .disconnect = zero_disconnect, ++ ++ .suspend = zero_suspend, ++ .resume = zero_resume, ++ ++ .driver = { ++ .name = (char *) shortname, ++ // .shutdown = ... ++ // .suspend = ... ++ // .resume = ... ++ }, ++}; ++ ++MODULE_AUTHOR ("David Brownell"); ++MODULE_LICENSE ("Dual BSD/GPL"); ++ ++static struct proc_dir_entry *pdir, *pfile; ++ ++static int isoc_read_data (char *page, char **start, ++ off_t off, int count, ++ int *eof, void *data) ++{ ++ int i; ++ static int c = 0; ++ static int done = 0; ++ static int s = 0; ++ ++/* ++ printk ("\ncount: %d\n", count); ++ printk ("rbuf_start: %d\n", rbuf_start); ++ printk ("rbuf_len: %d\n", rbuf_len); ++ printk ("off: %d\n", off); ++ printk ("start: %p\n\n", *start); ++*/ ++ if (done) { ++ c = 0; ++ done = 0; ++ *eof = 1; ++ return 0; ++ } ++ ++ if (c == 0) { ++ if (rbuf_len == RBUF_LEN) ++ s = rbuf_start; ++ else s = 0; ++ } ++ ++ for (i=0; i= rbuf_len) { ++ *eof = 1; ++ done = 1; ++ } ++ ++ ++ return i; ++} ++ ++static int __init init (void) ++{ ++ ++ int retval = 0; ++ ++ pdir = proc_mkdir("isoc_test", NULL); ++ if(pdir == NULL) { ++ retval = -ENOMEM; ++ printk("Error creating dir\n"); ++ goto done; ++ } ++ pdir->owner = THIS_MODULE; ++ ++ pfile = create_proc_read_entry("isoc_data", ++ 0444, pdir, ++ isoc_read_data, ++ NULL); ++ if (pfile == NULL) { ++ retval = -ENOMEM; ++ printk("Error creating file\n"); ++ goto no_file; ++ } ++ pfile->owner = THIS_MODULE; ++ ++ return usb_gadget_register_driver (&zero_driver); ++ ++ no_file: ++ remove_proc_entry("isoc_data", NULL); ++ done: ++ return retval; ++} ++module_init (init); ++ ++static void __exit cleanup (void) ++{ ++ ++ usb_gadget_unregister_driver (&zero_driver); ++ ++ remove_proc_entry("isoc_data", pdir); ++ remove_proc_entry("isoc_test", NULL); ++} ++module_exit (cleanup); +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_cfi_common.h +@@ -0,0 +1,142 @@ ++/* ========================================================================== ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++#if !defined(__DWC_CFI_COMMON_H__) ++#define __DWC_CFI_COMMON_H__ ++ ++//#include ++ ++/** ++ * @file ++ * ++ * This file contains the CFI specific common constants, interfaces ++ * (functions and macros) and structures for Linux. No PCD specific ++ * data structure or definition is to be included in this file. ++ * ++ */ ++ ++/** This is a request for all Core Features */ ++#define VEN_CORE_GET_FEATURES 0xB1 ++ ++/** This is a request to get the value of a specific Core Feature */ ++#define VEN_CORE_GET_FEATURE 0xB2 ++ ++/** This command allows the host to set the value of a specific Core Feature */ ++#define VEN_CORE_SET_FEATURE 0xB3 ++ ++/** This command allows the host to set the default values of ++ * either all or any specific Core Feature ++ */ ++#define VEN_CORE_RESET_FEATURES 0xB4 ++ ++/** This command forces the PCD to write the deferred values of a Core Features */ ++#define VEN_CORE_ACTIVATE_FEATURES 0xB5 ++ ++/** This request reads a DWORD value from a register at the specified offset */ ++#define VEN_CORE_READ_REGISTER 0xB6 ++ ++/** This request writes a DWORD value into a register at the specified offset */ ++#define VEN_CORE_WRITE_REGISTER 0xB7 ++ ++/** This structure is the header of the Core Features dataset returned to ++ * the Host ++ */ ++struct cfi_all_features_header { ++/** The features header structure length is */ ++#define CFI_ALL_FEATURES_HDR_LEN 8 ++ /** ++ * The total length of the features dataset returned to the Host ++ */ ++ uint16_t wTotalLen; ++ ++ /** ++ * CFI version number inBinary-Coded Decimal (i.e., 1.00 is 100H). ++ * This field identifies the version of the CFI Specification with which ++ * the device is compliant. ++ */ ++ uint16_t wVersion; ++ ++ /** The ID of the Core */ ++ uint16_t wCoreID; ++#define CFI_CORE_ID_UDC 1 ++#define CFI_CORE_ID_OTG 2 ++#define CFI_CORE_ID_WUDEV 3 ++ ++ /** Number of features returned by VEN_CORE_GET_FEATURES request */ ++ uint16_t wNumFeatures; ++} UPACKED; ++ ++typedef struct cfi_all_features_header cfi_all_features_header_t; ++ ++/** This structure is a header of the Core Feature descriptor dataset returned to ++ * the Host after the VEN_CORE_GET_FEATURES request ++ */ ++struct cfi_feature_desc_header { ++#define CFI_FEATURE_DESC_HDR_LEN 8 ++ ++ /** The feature ID */ ++ uint16_t wFeatureID; ++ ++ /** Length of this feature descriptor in bytes - including the ++ * length of the feature name string ++ */ ++ uint16_t wLength; ++ ++ /** The data length of this feature in bytes */ ++ uint16_t wDataLength; ++ ++ /** ++ * Attributes of this features ++ * D0: Access rights ++ * 0 - Read/Write ++ * 1 - Read only ++ */ ++ uint8_t bmAttributes; ++#define CFI_FEATURE_ATTR_RO 1 ++#define CFI_FEATURE_ATTR_RW 0 ++ ++ /** Length of the feature name in bytes */ ++ uint8_t bNameLen; ++ ++ /** The feature name buffer */ ++ //uint8_t *name; ++} UPACKED; ++ ++typedef struct cfi_feature_desc_header cfi_feature_desc_header_t; ++ ++/** ++ * This structure describes a NULL terminated string referenced by its id field. ++ * It is very similar to usb_string structure but has the id field type set to 16-bit. ++ */ ++struct cfi_string { ++ uint16_t id; ++ const uint8_t *s; ++}; ++typedef struct cfi_string cfi_string_t; ++ ++#endif +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_adp.c +@@ -0,0 +1,854 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_adp.c $ ++ * $Revision: #12 $ ++ * $Date: 2011/10/26 $ ++ * $Change: 1873028 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++#include "dwc_os.h" ++#include "dwc_otg_regs.h" ++#include "dwc_otg_cil.h" ++#include "dwc_otg_adp.h" ++ ++/** @file ++ * ++ * This file contains the most of the Attach Detect Protocol implementation for ++ * the driver to support OTG Rev2.0. ++ * ++ */ ++ ++void dwc_otg_adp_write_reg(dwc_otg_core_if_t * core_if, uint32_t value) ++{ ++ adpctl_data_t adpctl; ++ ++ adpctl.d32 = value; ++ adpctl.b.ar = 0x2; ++ ++ DWC_WRITE_REG32(&core_if->core_global_regs->adpctl, adpctl.d32); ++ ++ while (adpctl.b.ar) { ++ adpctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->adpctl); ++ } ++ ++} ++ ++/** ++ * Function is called to read ADP registers ++ */ ++uint32_t dwc_otg_adp_read_reg(dwc_otg_core_if_t * core_if) ++{ ++ adpctl_data_t adpctl; ++ ++ adpctl.d32 = 0; ++ adpctl.b.ar = 0x1; ++ ++ DWC_WRITE_REG32(&core_if->core_global_regs->adpctl, adpctl.d32); ++ ++ while (adpctl.b.ar) { ++ adpctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->adpctl); ++ } ++ ++ return adpctl.d32; ++} ++ ++/** ++ * Function is called to read ADPCTL register and filter Write-clear bits ++ */ ++uint32_t dwc_otg_adp_read_reg_filter(dwc_otg_core_if_t * core_if) ++{ ++ adpctl_data_t adpctl; ++ ++ adpctl.d32 = dwc_otg_adp_read_reg(core_if); ++ adpctl.b.adp_tmout_int = 0; ++ adpctl.b.adp_prb_int = 0; ++ adpctl.b.adp_tmout_int = 0; ++ ++ return adpctl.d32; ++} ++ ++/** ++ * Function is called to write ADP registers ++ */ ++void dwc_otg_adp_modify_reg(dwc_otg_core_if_t * core_if, uint32_t clr, ++ uint32_t set) ++{ ++ dwc_otg_adp_write_reg(core_if, ++ (dwc_otg_adp_read_reg(core_if) & (~clr)) | set); ++} ++ ++static void adp_sense_timeout(void *ptr) ++{ ++ dwc_otg_core_if_t *core_if = (dwc_otg_core_if_t *) ptr; ++ core_if->adp.sense_timer_started = 0; ++ DWC_PRINTF("ADP SENSE TIMEOUT\n"); ++ if (core_if->adp_enable) { ++ dwc_otg_adp_sense_stop(core_if); ++ dwc_otg_adp_probe_start(core_if); ++ } ++} ++ ++/** ++ * This function is called when the ADP vbus timer expires. Timeout is 1.1s. ++ */ ++static void adp_vbuson_timeout(void *ptr) ++{ ++ gpwrdn_data_t gpwrdn; ++ dwc_otg_core_if_t *core_if = (dwc_otg_core_if_t *) ptr; ++ hprt0_data_t hprt0 = {.d32 = 0 }; ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ DWC_PRINTF("%s: 1.1 seconds expire after turning on VBUS\n",__FUNCTION__); ++ if (core_if) { ++ core_if->adp.vbuson_timer_started = 0; ++ /* Turn off vbus */ ++ hprt0.b.prtpwr = 1; ++ DWC_MODIFY_REG32(core_if->host_if->hprt0, hprt0.d32, 0); ++ gpwrdn.d32 = 0; ++ ++ /* Power off the core */ ++ if (core_if->power_down == 2) { ++ /* Enable Wakeup Logic */ ++// gpwrdn.b.wkupactiv = 1; ++ gpwrdn.b.pmuactv = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ gpwrdn.b.pwrdnclmp = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, ++ gpwrdn.d32); ++ ++ /* Suspend the Phy Clock */ ++ pcgcctl.b.stoppclk = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, 0, pcgcctl.d32); ++ ++ /* Switch on VDD */ ++// gpwrdn.b.wkupactiv = 1; ++ gpwrdn.b.pmuactv = 1; ++ gpwrdn.b.pwrdnrstn = 1; ++ gpwrdn.b.pwrdnclmp = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, ++ gpwrdn.d32); ++ } else { ++ /* Enable Power Down Logic */ ++ gpwrdn.b.pmuintsel = 1; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ } ++ ++ /* Power off the core */ ++ if (core_if->power_down == 2) { ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, ++ gpwrdn.d32, 0); ++ } ++ ++ /* Unmask SRP detected interrupt from Power Down Logic */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.srp_det_msk = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ ++ dwc_otg_adp_probe_start(core_if); ++ dwc_otg_dump_global_registers(core_if); ++ dwc_otg_dump_host_registers(core_if); ++ } ++ ++} ++ ++/** ++ * Start the ADP Initial Probe timer to detect if Port Connected interrupt is ++ * not asserted within 1.1 seconds. ++ * ++ * @param core_if the pointer to core_if strucure. ++ */ ++void dwc_otg_adp_vbuson_timer_start(dwc_otg_core_if_t * core_if) ++{ ++ core_if->adp.vbuson_timer_started = 1; ++ if (core_if->adp.vbuson_timer) ++ { ++ DWC_PRINTF("SCHEDULING VBUSON TIMER\n"); ++ /* 1.1 secs + 60ms necessary for cil_hcd_start*/ ++ DWC_TIMER_SCHEDULE(core_if->adp.vbuson_timer, 1160); ++ } else { ++ DWC_WARN("VBUSON_TIMER = %p\n",core_if->adp.vbuson_timer); ++ } ++} ++ ++#if 0 ++/** ++ * Masks all DWC OTG core interrupts ++ * ++ */ ++static void mask_all_interrupts(dwc_otg_core_if_t * core_if) ++{ ++ int i; ++ gahbcfg_data_t ahbcfg = {.d32 = 0 }; ++ ++ /* Mask Host Interrupts */ ++ ++ /* Clear and disable HCINTs */ ++ for (i = 0; i < core_if->core_params->host_channels; i++) { ++ DWC_WRITE_REG32(&core_if->host_if->hc_regs[i]->hcintmsk, 0); ++ DWC_WRITE_REG32(&core_if->host_if->hc_regs[i]->hcint, 0xFFFFFFFF); ++ ++ } ++ ++ /* Clear and disable HAINT */ ++ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->haintmsk, 0x0000); ++ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->haint, 0xFFFFFFFF); ++ ++ /* Mask Device Interrupts */ ++ if (!core_if->multiproc_int_enable) { ++ /* Clear and disable IN Endpoint interrupts */ ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->diepmsk, 0); ++ for (i = 0; i <= core_if->dev_if->num_in_eps; i++) { ++ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[i]-> ++ diepint, 0xFFFFFFFF); ++ } ++ ++ /* Clear and disable OUT Endpoint interrupts */ ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->doepmsk, 0); ++ for (i = 0; i <= core_if->dev_if->num_out_eps; i++) { ++ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[i]-> ++ doepint, 0xFFFFFFFF); ++ } ++ ++ /* Clear and disable DAINT */ ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->daint, ++ 0xFFFFFFFF); ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->daintmsk, 0); ++ } else { ++ for (i = 0; i < core_if->dev_if->num_in_eps; ++i) { ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs-> ++ diepeachintmsk[i], 0); ++ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[i]-> ++ diepint, 0xFFFFFFFF); ++ } ++ ++ for (i = 0; i < core_if->dev_if->num_out_eps; ++i) { ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs-> ++ doepeachintmsk[i], 0); ++ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[i]-> ++ doepint, 0xFFFFFFFF); ++ } ++ ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->deachintmsk, ++ 0); ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->deachint, ++ 0xFFFFFFFF); ++ ++ } ++ ++ /* Disable interrupts */ ++ ahbcfg.b.glblintrmsk = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gahbcfg, ahbcfg.d32, 0); ++ ++ /* Disable all interrupts. */ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, 0); ++ ++ /* Clear any pending interrupts */ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF); ++ ++ /* Clear any pending OTG Interrupts */ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gotgint, 0xFFFFFFFF); ++} ++ ++/** ++ * Unmask Port Connection Detected interrupt ++ * ++ */ ++static void unmask_conn_det_intr(dwc_otg_core_if_t * core_if) ++{ ++ gintmsk_data_t gintmsk = {.d32 = 0,.b.portintr = 1 }; ++ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, gintmsk.d32); ++} ++#endif ++ ++/** ++ * Starts the ADP Probing ++ * ++ * @param core_if the pointer to core_if structure. ++ */ ++uint32_t dwc_otg_adp_probe_start(dwc_otg_core_if_t * core_if) ++{ ++ ++ adpctl_data_t adpctl = {.d32 = 0}; ++ gpwrdn_data_t gpwrdn; ++#if 0 ++ adpctl_data_t adpctl_int = {.d32 = 0, .b.adp_prb_int = 1, ++ .b.adp_sns_int = 1, b.adp_tmout_int}; ++#endif ++ dwc_otg_disable_global_interrupts(core_if); ++ DWC_PRINTF("ADP Probe Start\n"); ++ core_if->adp.probe_enabled = 1; ++ ++ adpctl.b.adpres = 1; ++ dwc_otg_adp_write_reg(core_if, adpctl.d32); ++ ++ while (adpctl.b.adpres) { ++ adpctl.d32 = dwc_otg_adp_read_reg(core_if); ++ } ++ ++ adpctl.d32 = 0; ++ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ ++ /* In Host mode unmask SRP detected interrupt */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.sts_chngint_msk = 1; ++ if (!gpwrdn.b.idsts) { ++ gpwrdn.b.srp_det_msk = 1; ++ } ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ ++ adpctl.b.adp_tmout_int_msk = 1; ++ adpctl.b.adp_prb_int_msk = 1; ++ adpctl.b.prb_dschg = 1; ++ adpctl.b.prb_delta = 1; ++ adpctl.b.prb_per = 1; ++ adpctl.b.adpen = 1; ++ adpctl.b.enaprb = 1; ++ ++ dwc_otg_adp_write_reg(core_if, adpctl.d32); ++ DWC_PRINTF("ADP Probe Finish\n"); ++ return 0; ++} ++ ++/** ++ * Starts the ADP Sense timer to detect if ADP Sense interrupt is not asserted ++ * within 3 seconds. ++ * ++ * @param core_if the pointer to core_if strucure. ++ */ ++void dwc_otg_adp_sense_timer_start(dwc_otg_core_if_t * core_if) ++{ ++ core_if->adp.sense_timer_started = 1; ++ DWC_TIMER_SCHEDULE(core_if->adp.sense_timer, 3000 /* 3 secs */ ); ++} ++ ++/** ++ * Starts the ADP Sense ++ * ++ * @param core_if the pointer to core_if strucure. ++ */ ++uint32_t dwc_otg_adp_sense_start(dwc_otg_core_if_t * core_if) ++{ ++ adpctl_data_t adpctl; ++ ++ DWC_PRINTF("ADP Sense Start\n"); ++ ++ /* Unmask ADP sense interrupt and mask all other from the core */ ++ adpctl.d32 = dwc_otg_adp_read_reg_filter(core_if); ++ adpctl.b.adp_sns_int_msk = 1; ++ dwc_otg_adp_write_reg(core_if, adpctl.d32); ++ dwc_otg_disable_global_interrupts(core_if); // vahrama ++ ++ /* Set ADP reset bit*/ ++ adpctl.d32 = dwc_otg_adp_read_reg_filter(core_if); ++ adpctl.b.adpres = 1; ++ dwc_otg_adp_write_reg(core_if, adpctl.d32); ++ ++ while (adpctl.b.adpres) { ++ adpctl.d32 = dwc_otg_adp_read_reg(core_if); ++ } ++ ++ adpctl.b.adpres = 0; ++ adpctl.b.adpen = 1; ++ adpctl.b.enasns = 1; ++ dwc_otg_adp_write_reg(core_if, adpctl.d32); ++ ++ dwc_otg_adp_sense_timer_start(core_if); ++ ++ return 0; ++} ++ ++/** ++ * Stops the ADP Probing ++ * ++ * @param core_if the pointer to core_if strucure. ++ */ ++uint32_t dwc_otg_adp_probe_stop(dwc_otg_core_if_t * core_if) ++{ ++ ++ adpctl_data_t adpctl; ++ DWC_PRINTF("Stop ADP probe\n"); ++ core_if->adp.probe_enabled = 0; ++ core_if->adp.probe_counter = 0; ++ adpctl.d32 = dwc_otg_adp_read_reg(core_if); ++ ++ adpctl.b.adpen = 0; ++ adpctl.b.adp_prb_int = 1; ++ adpctl.b.adp_tmout_int = 1; ++ adpctl.b.adp_sns_int = 1; ++ dwc_otg_adp_write_reg(core_if, adpctl.d32); ++ ++ return 0; ++} ++ ++/** ++ * Stops the ADP Sensing ++ * ++ * @param core_if the pointer to core_if strucure. ++ */ ++uint32_t dwc_otg_adp_sense_stop(dwc_otg_core_if_t * core_if) ++{ ++ adpctl_data_t adpctl; ++ ++ core_if->adp.sense_enabled = 0; ++ ++ adpctl.d32 = dwc_otg_adp_read_reg_filter(core_if); ++ adpctl.b.enasns = 0; ++ adpctl.b.adp_sns_int = 1; ++ dwc_otg_adp_write_reg(core_if, adpctl.d32); ++ ++ return 0; ++} ++ ++/** ++ * Called to turn on the VBUS after initial ADP probe in host mode. ++ * If port power was already enabled in cil_hcd_start function then ++ * only schedule a timer. ++ * ++ * @param core_if the pointer to core_if structure. ++ */ ++void dwc_otg_adp_turnon_vbus(dwc_otg_core_if_t * core_if) ++{ ++ hprt0_data_t hprt0 = {.d32 = 0 }; ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ DWC_PRINTF("Turn on VBUS for 1.1s, port power is %d\n", hprt0.b.prtpwr); ++ ++ if (hprt0.b.prtpwr == 0) { ++ hprt0.b.prtpwr = 1; ++ //DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ } ++ ++ dwc_otg_adp_vbuson_timer_start(core_if); ++} ++ ++/** ++ * Called right after driver is loaded ++ * to perform initial actions for ADP ++ * ++ * @param core_if the pointer to core_if structure. ++ * @param is_host - flag for current mode of operation either from GINTSTS or GPWRDN ++ */ ++void dwc_otg_adp_start(dwc_otg_core_if_t * core_if, uint8_t is_host) ++{ ++ gpwrdn_data_t gpwrdn; ++ ++ DWC_PRINTF("ADP Initial Start\n"); ++ core_if->adp.adp_started = 1; ++ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF); ++ dwc_otg_disable_global_interrupts(core_if); ++ if (is_host) { ++ DWC_PRINTF("HOST MODE\n"); ++ /* Enable Power Down Logic Interrupt*/ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ /* Initialize first ADP probe to obtain Ramp Time value */ ++ core_if->adp.initial_probe = 1; ++ dwc_otg_adp_probe_start(core_if); ++ } else { ++ gotgctl_data_t gotgctl; ++ gotgctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->gotgctl); ++ DWC_PRINTF("DEVICE MODE\n"); ++ if (gotgctl.b.bsesvld == 0) { ++ /* Enable Power Down Logic Interrupt*/ ++ gpwrdn.d32 = 0; ++ DWC_PRINTF("VBUS is not valid - start ADP probe\n"); ++ gpwrdn.b.pmuintsel = 1; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ core_if->adp.initial_probe = 1; ++ dwc_otg_adp_probe_start(core_if); ++ } else { ++ DWC_PRINTF("VBUS is valid - initialize core as a Device\n"); ++ core_if->op_state = B_PERIPHERAL; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_pcd_start(core_if); ++ dwc_otg_dump_global_registers(core_if); ++ dwc_otg_dump_dev_registers(core_if); ++ } ++ } ++} ++ ++void dwc_otg_adp_init(dwc_otg_core_if_t * core_if) ++{ ++ core_if->adp.adp_started = 0; ++ core_if->adp.initial_probe = 0; ++ core_if->adp.probe_timer_values[0] = -1; ++ core_if->adp.probe_timer_values[1] = -1; ++ core_if->adp.probe_enabled = 0; ++ core_if->adp.sense_enabled = 0; ++ core_if->adp.sense_timer_started = 0; ++ core_if->adp.vbuson_timer_started = 0; ++ core_if->adp.probe_counter = 0; ++ core_if->adp.gpwrdn = 0; ++ core_if->adp.attached = DWC_OTG_ADP_UNKOWN; ++ /* Initialize timers */ ++ core_if->adp.sense_timer = ++ DWC_TIMER_ALLOC("ADP SENSE TIMER", adp_sense_timeout, core_if); ++ core_if->adp.vbuson_timer = ++ DWC_TIMER_ALLOC("ADP VBUS ON TIMER", adp_vbuson_timeout, core_if); ++ if (!core_if->adp.sense_timer || !core_if->adp.vbuson_timer) ++ { ++ DWC_ERROR("Could not allocate memory for ADP timers\n"); ++ } ++} ++ ++void dwc_otg_adp_remove(dwc_otg_core_if_t * core_if) ++{ ++ gpwrdn_data_t gpwrdn = { .d32 = 0 }; ++ gpwrdn.b.pmuintsel = 1; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ if (core_if->adp.probe_enabled) ++ dwc_otg_adp_probe_stop(core_if); ++ if (core_if->adp.sense_enabled) ++ dwc_otg_adp_sense_stop(core_if); ++ if (core_if->adp.sense_timer_started) ++ DWC_TIMER_CANCEL(core_if->adp.sense_timer); ++ if (core_if->adp.vbuson_timer_started) ++ DWC_TIMER_CANCEL(core_if->adp.vbuson_timer); ++ DWC_TIMER_FREE(core_if->adp.sense_timer); ++ DWC_TIMER_FREE(core_if->adp.vbuson_timer); ++} ++ ++///////////////////////////////////////////////////////////////////// ++////////////// ADP Interrupt Handlers /////////////////////////////// ++///////////////////////////////////////////////////////////////////// ++/** ++ * This function sets Ramp Timer values ++ */ ++static uint32_t set_timer_value(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ if (core_if->adp.probe_timer_values[0] == -1) { ++ core_if->adp.probe_timer_values[0] = val; ++ core_if->adp.probe_timer_values[1] = -1; ++ return 1; ++ } else { ++ core_if->adp.probe_timer_values[1] = ++ core_if->adp.probe_timer_values[0]; ++ core_if->adp.probe_timer_values[0] = val; ++ return 0; ++ } ++} ++ ++/** ++ * This function compares Ramp Timer values ++ */ ++static uint32_t compare_timer_values(dwc_otg_core_if_t * core_if) ++{ ++ uint32_t diff; ++ if (core_if->adp.probe_timer_values[0]>=core_if->adp.probe_timer_values[1]) ++ diff = core_if->adp.probe_timer_values[0]-core_if->adp.probe_timer_values[1]; ++ else ++ diff = core_if->adp.probe_timer_values[1]-core_if->adp.probe_timer_values[0]; ++ if(diff < 2) { ++ return 0; ++ } else { ++ return 1; ++ } ++} ++ ++/** ++ * This function handles ADP Probe Interrupts ++ */ ++static int32_t dwc_otg_adp_handle_prb_intr(dwc_otg_core_if_t * core_if, ++ uint32_t val) ++{ ++ adpctl_data_t adpctl = {.d32 = 0 }; ++ gpwrdn_data_t gpwrdn, temp; ++ adpctl.d32 = val; ++ ++ temp.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ core_if->adp.probe_counter++; ++ core_if->adp.gpwrdn = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ if (adpctl.b.rtim == 0 && !temp.b.idsts){ ++ DWC_PRINTF("RTIM value is 0\n"); ++ goto exit; ++ } ++ if (set_timer_value(core_if, adpctl.b.rtim) && ++ core_if->adp.initial_probe) { ++ core_if->adp.initial_probe = 0; ++ dwc_otg_adp_probe_stop(core_if); ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuactv = 1; ++ gpwrdn.b.pmuintsel = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF); ++ ++ /* check which value is for device mode and which for Host mode */ ++ if (!temp.b.idsts) { /* considered host mode value is 0 */ ++ /* ++ * Turn on VBUS after initial ADP probe. ++ */ ++ core_if->op_state = A_HOST; ++ dwc_otg_enable_global_interrupts(core_if); ++ DWC_SPINUNLOCK(core_if->lock); ++ cil_hcd_start(core_if); ++ dwc_otg_adp_turnon_vbus(core_if); ++ DWC_SPINLOCK(core_if->lock); ++ } else { ++ /* ++ * Initiate SRP after initial ADP probe. ++ */ ++ dwc_otg_enable_global_interrupts(core_if); ++ dwc_otg_initiate_srp(core_if); ++ } ++ } else if (core_if->adp.probe_counter > 2){ ++ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ if (compare_timer_values(core_if)) { ++ DWC_PRINTF("Difference in timer values !!! \n"); ++// core_if->adp.attached = DWC_OTG_ADP_ATTACHED; ++ dwc_otg_adp_probe_stop(core_if); ++ ++ /* Power on the core */ ++ if (core_if->power_down == 2) { ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ } ++ ++ /* check which value is for device mode and which for Host mode */ ++ if (!temp.b.idsts) { /* considered host mode value is 0 */ ++ /* Disable Interrupt from Power Down Logic */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, gpwrdn.d32, 0); ++ ++ /* ++ * Initialize the Core for Host mode. ++ */ ++ core_if->op_state = A_HOST; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_hcd_start(core_if); ++ } else { ++ gotgctl_data_t gotgctl; ++ /* Mask SRP detected interrupt from Power Down Logic */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.srp_det_msk = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, gpwrdn.d32, 0); ++ ++ /* Disable Power Down Logic */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, gpwrdn.d32, 0); ++ ++ /* ++ * Initialize the Core for Device mode. ++ */ ++ core_if->op_state = B_PERIPHERAL; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_pcd_start(core_if); ++ ++ gotgctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->gotgctl); ++ if (!gotgctl.b.bsesvld) { ++ dwc_otg_initiate_srp(core_if); ++ } ++ } ++ } ++ if (core_if->power_down == 2) { ++ if (gpwrdn.b.bsessvld) { ++ /* Mask SRP detected interrupt from Power Down Logic */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.srp_det_msk = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ /* Disable Power Down Logic */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ /* ++ * Initialize the Core for Device mode. ++ */ ++ core_if->op_state = B_PERIPHERAL; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_pcd_start(core_if); ++ } ++ } ++ } ++exit: ++ /* Clear interrupt */ ++ adpctl.d32 = dwc_otg_adp_read_reg(core_if); ++ adpctl.b.adp_prb_int = 1; ++ dwc_otg_adp_write_reg(core_if, adpctl.d32); ++ ++ return 0; ++} ++ ++/** ++ * This function hadles ADP Sense Interrupt ++ */ ++static int32_t dwc_otg_adp_handle_sns_intr(dwc_otg_core_if_t * core_if) ++{ ++ adpctl_data_t adpctl; ++ /* Stop ADP Sense timer */ ++ DWC_TIMER_CANCEL(core_if->adp.sense_timer); ++ ++ /* Restart ADP Sense timer */ ++ dwc_otg_adp_sense_timer_start(core_if); ++ ++ /* Clear interrupt */ ++ adpctl.d32 = dwc_otg_adp_read_reg(core_if); ++ adpctl.b.adp_sns_int = 1; ++ dwc_otg_adp_write_reg(core_if, adpctl.d32); ++ ++ return 0; ++} ++ ++/** ++ * This function handles ADP Probe Interrupts ++ */ ++static int32_t dwc_otg_adp_handle_prb_tmout_intr(dwc_otg_core_if_t * core_if, ++ uint32_t val) ++{ ++ adpctl_data_t adpctl = {.d32 = 0 }; ++ adpctl.d32 = val; ++ set_timer_value(core_if, adpctl.b.rtim); ++ ++ /* Clear interrupt */ ++ adpctl.d32 = dwc_otg_adp_read_reg(core_if); ++ adpctl.b.adp_tmout_int = 1; ++ dwc_otg_adp_write_reg(core_if, adpctl.d32); ++ ++ return 0; ++} ++ ++/** ++ * ADP Interrupt handler. ++ * ++ */ ++int32_t dwc_otg_adp_handle_intr(dwc_otg_core_if_t * core_if) ++{ ++ int retval = 0; ++ adpctl_data_t adpctl = {.d32 = 0}; ++ ++ adpctl.d32 = dwc_otg_adp_read_reg(core_if); ++ DWC_PRINTF("ADPCTL = %08x\n",adpctl.d32); ++ ++ if (adpctl.b.adp_sns_int & adpctl.b.adp_sns_int_msk) { ++ DWC_PRINTF("ADP Sense interrupt\n"); ++ retval |= dwc_otg_adp_handle_sns_intr(core_if); ++ } ++ if (adpctl.b.adp_tmout_int & adpctl.b.adp_tmout_int_msk) { ++ DWC_PRINTF("ADP timeout interrupt\n"); ++ retval |= dwc_otg_adp_handle_prb_tmout_intr(core_if, adpctl.d32); ++ } ++ if (adpctl.b.adp_prb_int & adpctl.b.adp_prb_int_msk) { ++ DWC_PRINTF("ADP Probe interrupt\n"); ++ adpctl.b.adp_prb_int = 1; ++ retval |= dwc_otg_adp_handle_prb_intr(core_if, adpctl.d32); ++ } ++ ++// dwc_otg_adp_modify_reg(core_if, adpctl.d32, 0); ++ //dwc_otg_adp_write_reg(core_if, adpctl.d32); ++ DWC_PRINTF("RETURN FROM ADP ISR\n"); ++ ++ return retval; ++} ++ ++/** ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++int32_t dwc_otg_adp_handle_srp_intr(dwc_otg_core_if_t * core_if) ++{ ++ ++#ifndef DWC_HOST_ONLY ++ hprt0_data_t hprt0; ++ gpwrdn_data_t gpwrdn; ++ DWC_DEBUGPL(DBG_ANY, "++ Power Down Logic Session Request Interrupt++\n"); ++ ++ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ /* check which value is for device mode and which for Host mode */ ++ if (!gpwrdn.b.idsts) { /* considered host mode value is 0 */ ++ DWC_PRINTF("SRP: Host mode\n"); ++ ++ if (core_if->adp_enable) { ++ dwc_otg_adp_probe_stop(core_if); ++ ++ /* Power on the core */ ++ if (core_if->power_down == 2) { ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ } ++ ++ core_if->op_state = A_HOST; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_hcd_start(core_if); ++ } ++ ++ /* Turn on the port power bit. */ ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtpwr = 1; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ ++ /* Start the Connection timer. So a message can be displayed ++ * if connect does not occur within 10 seconds. */ ++ cil_hcd_session_start(core_if); ++ } else { ++ DWC_PRINTF("SRP: Device mode %s\n", __FUNCTION__); ++ if (core_if->adp_enable) { ++ dwc_otg_adp_probe_stop(core_if); ++ ++ /* Power on the core */ ++ if (core_if->power_down == 2) { ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ } ++ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuactv = 0; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, ++ gpwrdn.d32); ++ ++ core_if->op_state = B_PERIPHERAL; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_pcd_start(core_if); ++ } ++ } ++#endif ++ return 1; ++} +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_adp.h +@@ -0,0 +1,80 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_adp.h $ ++ * $Revision: #7 $ ++ * $Date: 2011/10/24 $ ++ * $Change: 1871159 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++#ifndef __DWC_OTG_ADP_H__ ++#define __DWC_OTG_ADP_H__ ++ ++/** ++ * @file ++ * ++ * This file contains the Attach Detect Protocol interfaces and defines ++ * (functions) and structures for Linux. ++ * ++ */ ++ ++#define DWC_OTG_ADP_UNATTACHED 0 ++#define DWC_OTG_ADP_ATTACHED 1 ++#define DWC_OTG_ADP_UNKOWN 2 ++ ++typedef struct dwc_otg_adp { ++ uint32_t adp_started; ++ uint32_t initial_probe; ++ int32_t probe_timer_values[2]; ++ uint32_t probe_enabled; ++ uint32_t sense_enabled; ++ dwc_timer_t *sense_timer; ++ uint32_t sense_timer_started; ++ dwc_timer_t *vbuson_timer; ++ uint32_t vbuson_timer_started; ++ uint32_t attached; ++ uint32_t probe_counter; ++ uint32_t gpwrdn; ++} dwc_otg_adp_t; ++ ++/** ++ * Attach Detect Protocol functions ++ */ ++ ++extern void dwc_otg_adp_write_reg(dwc_otg_core_if_t * core_if, uint32_t value); ++extern uint32_t dwc_otg_adp_read_reg(dwc_otg_core_if_t * core_if); ++extern uint32_t dwc_otg_adp_probe_start(dwc_otg_core_if_t * core_if); ++extern uint32_t dwc_otg_adp_sense_start(dwc_otg_core_if_t * core_if); ++extern uint32_t dwc_otg_adp_probe_stop(dwc_otg_core_if_t * core_if); ++extern uint32_t dwc_otg_adp_sense_stop(dwc_otg_core_if_t * core_if); ++extern void dwc_otg_adp_start(dwc_otg_core_if_t * core_if, uint8_t is_host); ++extern void dwc_otg_adp_init(dwc_otg_core_if_t * core_if); ++extern void dwc_otg_adp_remove(dwc_otg_core_if_t * core_if); ++extern int32_t dwc_otg_adp_handle_intr(dwc_otg_core_if_t * core_if); ++extern int32_t dwc_otg_adp_handle_srp_intr(dwc_otg_core_if_t * core_if); ++ ++#endif //__DWC_OTG_ADP_H__ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_attr.c +@@ -0,0 +1,1212 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_attr.c $ ++ * $Revision: #44 $ ++ * $Date: 2010/11/29 $ ++ * $Change: 1636033 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++/** @file ++ * ++ * The diagnostic interface will provide access to the controller for ++ * bringing up the hardware and testing. The Linux driver attributes ++ * feature will be used to provide the Linux Diagnostic ++ * Interface. These attributes are accessed through sysfs. ++ */ ++ ++/** @page "Linux Module Attributes" ++ * ++ * The Linux module attributes feature is used to provide the Linux ++ * Diagnostic Interface. These attributes are accessed through sysfs. ++ * The diagnostic interface will provide access to the controller for ++ * bringing up the hardware and testing. ++ ++ The following table shows the attributes. ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++
Name Description Access
mode Returns the current mode: 0 for device mode, 1 for host mode Read
hnpcapable Gets or sets the "HNP-capable" bit in the Core USB Configuraton Register. ++ Read returns the current value. Read/Write
srpcapable Gets or sets the "SRP-capable" bit in the Core USB Configuraton Register. ++ Read returns the current value. Read/Write
hsic_connect Gets or sets the "HSIC-Connect" bit in the GLPMCFG Register. ++ Read returns the current value. Read/Write
inv_sel_hsic Gets or sets the "Invert Select HSIC" bit in the GLPMFG Register. ++ Read returns the current value. Read/Write
hnp Initiates the Host Negotiation Protocol. Read returns the status. Read/Write
srp Initiates the Session Request Protocol. Read returns the status. Read/Write
buspower Gets or sets the Power State of the bus (0 - Off or 1 - On) Read/Write
bussuspend Suspends the USB bus. Read/Write
busconnected Gets the connection status of the bus Read
gotgctl Gets or sets the Core Control Status Register. Read/Write
gusbcfg Gets or sets the Core USB Configuration Register Read/Write
grxfsiz Gets or sets the Receive FIFO Size Register Read/Write
gnptxfsiz Gets or sets the non-periodic Transmit Size Register Read/Write
gpvndctl Gets or sets the PHY Vendor Control Register Read/Write
ggpio Gets the value in the lower 16-bits of the General Purpose IO Register ++ or sets the upper 16 bits. Read/Write
guid Gets or sets the value of the User ID Register Read/Write
gsnpsid Gets the value of the Synopsys ID Regester Read
devspeed Gets or sets the device speed setting in the DCFG register Read/Write
enumspeed Gets the device enumeration Speed. Read
hptxfsiz Gets the value of the Host Periodic Transmit FIFO Read
hprt0 Gets or sets the value in the Host Port Control and Status Register Read/Write
regoffset Sets the register offset for the next Register Access Read/Write
regvalue Gets or sets the value of the register at the offset in the regoffset attribute. Read/Write
remote_wakeup On read, shows the status of Remote Wakeup. On write, initiates a remote ++ wakeup of the host. When bit 0 is 1 and Remote Wakeup is enabled, the Remote ++ Wakeup signalling bit in the Device Control Register is set for 1 ++ milli-second. Read/Write
rem_wakeup_pwrdn On read, shows the status core - hibernated or not. On write, initiates ++ a remote wakeup of the device from Hibernation. Read/Write
mode_ch_tim_en This bit is used to enable or disable the host core to wait for 200 PHY ++ clock cycles at the end of Resume to change the opmode signal to the PHY to 00 ++ after Suspend or LPM. Read/Write
fr_interval On read, shows the value of HFIR Frame Interval. On write, dynamically ++ reload HFIR register during runtime. The application can write a value to this ++ register only after the Port Enable bit of the Host Port Control and Status ++ register (HPRT.PrtEnaPort) has been set Read/Write
disconnect_us On read, shows the status of disconnect_device_us. On write, sets disconnect_us ++ which causes soft disconnect for 100us. Applicable only for device mode of operation. Read/Write
regdump Dumps the contents of core registers. Read
spramdump Dumps the contents of core registers. Read
hcddump Dumps the current HCD state. Read
hcd_frrem Shows the average value of the Frame Remaining ++ field in the Host Frame Number/Frame Remaining register when an SOF interrupt ++ occurs. This can be used to determine the average interrupt latency. Also ++ shows the average Frame Remaining value for start_transfer and the "a" and ++ "b" sample points. The "a" and "b" sample points may be used during debugging ++ bto determine how long it takes to execute a section of the HCD code. Read
rd_reg_test Displays the time required to read the GNPTXFSIZ register many times ++ (the output shows the number of times the register is read). ++ Read
wr_reg_test Displays the time required to write the GNPTXFSIZ register many times ++ (the output shows the number of times the register is written). ++ Read
lpm_response Gets or sets lpm_response mode. Applicable only in device mode. ++ Write
sleep_status Shows sleep status of device. ++ Read
++ ++ Example usage: ++ To get the current mode: ++ cat /sys/devices/lm0/mode ++ ++ To power down the USB: ++ echo 0 > /sys/devices/lm0/buspower ++ */ ++ ++#include "dwc_otg_os_dep.h" ++#include "dwc_os.h" ++#include "dwc_otg_driver.h" ++#include "dwc_otg_attr.h" ++#include "dwc_otg_core_if.h" ++#include "dwc_otg_pcd_if.h" ++#include "dwc_otg_hcd_if.h" ++ ++/* ++ * MACROs for defining sysfs attribute ++ */ ++#ifdef LM_INTERFACE ++ ++#define DWC_OTG_DEVICE_ATTR_BITFIELD_SHOW(_otg_attr_name_,_string_) \ ++static ssize_t _otg_attr_name_##_show (struct device *_dev, struct device_attribute *attr, char *buf) \ ++{ \ ++ struct lm_device *lm_dev = container_of(_dev, struct lm_device, dev); \ ++ dwc_otg_device_t *otg_dev = lm_get_drvdata(lm_dev); \ ++ uint32_t val; \ ++ val = dwc_otg_get_##_otg_attr_name_ (otg_dev->core_if); \ ++ return sprintf (buf, "%s = 0x%x\n", _string_, val); \ ++} ++#define DWC_OTG_DEVICE_ATTR_BITFIELD_STORE(_otg_attr_name_,_string_) \ ++static ssize_t _otg_attr_name_##_store (struct device *_dev, struct device_attribute *attr, \ ++ const char *buf, size_t count) \ ++{ \ ++ struct lm_device *lm_dev = container_of(_dev, struct lm_device, dev); \ ++ dwc_otg_device_t *otg_dev = lm_get_drvdata(lm_dev); \ ++ uint32_t set = simple_strtoul(buf, NULL, 16); \ ++ dwc_otg_set_##_otg_attr_name_(otg_dev->core_if, set);\ ++ return count; \ ++} ++ ++#elif defined(PCI_INTERFACE) ++ ++#define DWC_OTG_DEVICE_ATTR_BITFIELD_SHOW(_otg_attr_name_,_string_) \ ++static ssize_t _otg_attr_name_##_show (struct device *_dev, struct device_attribute *attr, char *buf) \ ++{ \ ++ dwc_otg_device_t *otg_dev = dev_get_drvdata(_dev); \ ++ uint32_t val; \ ++ val = dwc_otg_get_##_otg_attr_name_ (otg_dev->core_if); \ ++ return sprintf (buf, "%s = 0x%x\n", _string_, val); \ ++} ++#define DWC_OTG_DEVICE_ATTR_BITFIELD_STORE(_otg_attr_name_,_string_) \ ++static ssize_t _otg_attr_name_##_store (struct device *_dev, struct device_attribute *attr, \ ++ const char *buf, size_t count) \ ++{ \ ++ dwc_otg_device_t *otg_dev = dev_get_drvdata(_dev); \ ++ uint32_t set = simple_strtoul(buf, NULL, 16); \ ++ dwc_otg_set_##_otg_attr_name_(otg_dev->core_if, set);\ ++ return count; \ ++} ++ ++#elif defined(PLATFORM_INTERFACE) ++ ++#define DWC_OTG_DEVICE_ATTR_BITFIELD_SHOW(_otg_attr_name_,_string_) \ ++static ssize_t _otg_attr_name_##_show (struct device *_dev, struct device_attribute *attr, char *buf) \ ++{ \ ++ struct platform_device *platform_dev = \ ++ container_of(_dev, struct platform_device, dev); \ ++ dwc_otg_device_t *otg_dev = platform_get_drvdata(platform_dev); \ ++ uint32_t val; \ ++ DWC_PRINTF("%s(%p) -> platform_dev %p, otg_dev %p\n", \ ++ __func__, _dev, platform_dev, otg_dev); \ ++ val = dwc_otg_get_##_otg_attr_name_ (otg_dev->core_if); \ ++ return sprintf (buf, "%s = 0x%x\n", _string_, val); \ ++} ++#define DWC_OTG_DEVICE_ATTR_BITFIELD_STORE(_otg_attr_name_,_string_) \ ++static ssize_t _otg_attr_name_##_store (struct device *_dev, struct device_attribute *attr, \ ++ const char *buf, size_t count) \ ++{ \ ++ struct platform_device *platform_dev = container_of(_dev, struct platform_device, dev); \ ++ dwc_otg_device_t *otg_dev = platform_get_drvdata(platform_dev); \ ++ uint32_t set = simple_strtoul(buf, NULL, 16); \ ++ dwc_otg_set_##_otg_attr_name_(otg_dev->core_if, set);\ ++ return count; \ ++} ++#endif ++ ++/* ++ * MACROs for defining sysfs attribute for 32-bit registers ++ */ ++#ifdef LM_INTERFACE ++#define DWC_OTG_DEVICE_ATTR_REG_SHOW(_otg_attr_name_,_string_) \ ++static ssize_t _otg_attr_name_##_show (struct device *_dev, struct device_attribute *attr, char *buf) \ ++{ \ ++ struct lm_device *lm_dev = container_of(_dev, struct lm_device, dev); \ ++ dwc_otg_device_t *otg_dev = lm_get_drvdata(lm_dev); \ ++ uint32_t val; \ ++ val = dwc_otg_get_##_otg_attr_name_ (otg_dev->core_if); \ ++ return sprintf (buf, "%s = 0x%08x\n", _string_, val); \ ++} ++#define DWC_OTG_DEVICE_ATTR_REG_STORE(_otg_attr_name_,_string_) \ ++static ssize_t _otg_attr_name_##_store (struct device *_dev, struct device_attribute *attr, \ ++ const char *buf, size_t count) \ ++{ \ ++ struct lm_device *lm_dev = container_of(_dev, struct lm_device, dev); \ ++ dwc_otg_device_t *otg_dev = lm_get_drvdata(lm_dev); \ ++ uint32_t val = simple_strtoul(buf, NULL, 16); \ ++ dwc_otg_set_##_otg_attr_name_ (otg_dev->core_if, val); \ ++ return count; \ ++} ++#elif defined(PCI_INTERFACE) ++#define DWC_OTG_DEVICE_ATTR_REG_SHOW(_otg_attr_name_,_string_) \ ++static ssize_t _otg_attr_name_##_show (struct device *_dev, struct device_attribute *attr, char *buf) \ ++{ \ ++ dwc_otg_device_t *otg_dev = dev_get_drvdata(_dev); \ ++ uint32_t val; \ ++ val = dwc_otg_get_##_otg_attr_name_ (otg_dev->core_if); \ ++ return sprintf (buf, "%s = 0x%08x\n", _string_, val); \ ++} ++#define DWC_OTG_DEVICE_ATTR_REG_STORE(_otg_attr_name_,_string_) \ ++static ssize_t _otg_attr_name_##_store (struct device *_dev, struct device_attribute *attr, \ ++ const char *buf, size_t count) \ ++{ \ ++ dwc_otg_device_t *otg_dev = dev_get_drvdata(_dev); \ ++ uint32_t val = simple_strtoul(buf, NULL, 16); \ ++ dwc_otg_set_##_otg_attr_name_ (otg_dev->core_if, val); \ ++ return count; \ ++} ++ ++#elif defined(PLATFORM_INTERFACE) ++#include "dwc_otg_dbg.h" ++#define DWC_OTG_DEVICE_ATTR_REG_SHOW(_otg_attr_name_,_string_) \ ++static ssize_t _otg_attr_name_##_show (struct device *_dev, struct device_attribute *attr, char *buf) \ ++{ \ ++ struct platform_device *platform_dev = container_of(_dev, struct platform_device, dev); \ ++ dwc_otg_device_t *otg_dev = platform_get_drvdata(platform_dev); \ ++ uint32_t val; \ ++ DWC_PRINTF("%s(%p) -> platform_dev %p, otg_dev %p\n", \ ++ __func__, _dev, platform_dev, otg_dev); \ ++ val = dwc_otg_get_##_otg_attr_name_ (otg_dev->core_if); \ ++ return sprintf (buf, "%s = 0x%08x\n", _string_, val); \ ++} ++#define DWC_OTG_DEVICE_ATTR_REG_STORE(_otg_attr_name_,_string_) \ ++static ssize_t _otg_attr_name_##_store (struct device *_dev, struct device_attribute *attr, \ ++ const char *buf, size_t count) \ ++{ \ ++ struct platform_device *platform_dev = container_of(_dev, struct platform_device, dev); \ ++ dwc_otg_device_t *otg_dev = platform_get_drvdata(platform_dev); \ ++ uint32_t val = simple_strtoul(buf, NULL, 16); \ ++ dwc_otg_set_##_otg_attr_name_ (otg_dev->core_if, val); \ ++ return count; \ ++} ++ ++#endif ++ ++#define DWC_OTG_DEVICE_ATTR_BITFIELD_RW(_otg_attr_name_,_string_) \ ++DWC_OTG_DEVICE_ATTR_BITFIELD_SHOW(_otg_attr_name_,_string_) \ ++DWC_OTG_DEVICE_ATTR_BITFIELD_STORE(_otg_attr_name_,_string_) \ ++DEVICE_ATTR(_otg_attr_name_,0644,_otg_attr_name_##_show,_otg_attr_name_##_store); ++ ++#define DWC_OTG_DEVICE_ATTR_BITFIELD_RO(_otg_attr_name_,_string_) \ ++DWC_OTG_DEVICE_ATTR_BITFIELD_SHOW(_otg_attr_name_,_string_) \ ++DEVICE_ATTR(_otg_attr_name_,0444,_otg_attr_name_##_show,NULL); ++ ++#define DWC_OTG_DEVICE_ATTR_REG32_RW(_otg_attr_name_,_addr_,_string_) \ ++DWC_OTG_DEVICE_ATTR_REG_SHOW(_otg_attr_name_,_string_) \ ++DWC_OTG_DEVICE_ATTR_REG_STORE(_otg_attr_name_,_string_) \ ++DEVICE_ATTR(_otg_attr_name_,0644,_otg_attr_name_##_show,_otg_attr_name_##_store); ++ ++#define DWC_OTG_DEVICE_ATTR_REG32_RO(_otg_attr_name_,_addr_,_string_) \ ++DWC_OTG_DEVICE_ATTR_REG_SHOW(_otg_attr_name_,_string_) \ ++DEVICE_ATTR(_otg_attr_name_,0444,_otg_attr_name_##_show,NULL); ++ ++/** @name Functions for Show/Store of Attributes */ ++/**@{*/ ++ ++/** ++ * Helper function returning the otg_device structure of the given device ++ */ ++static dwc_otg_device_t *dwc_otg_drvdev(struct device *_dev) ++{ ++ dwc_otg_device_t *otg_dev; ++ DWC_OTG_GETDRVDEV(otg_dev, _dev); ++ return otg_dev; ++} ++ ++/** ++ * Show the register offset of the Register Access. ++ */ ++static ssize_t regoffset_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ return snprintf(buf, sizeof("0xFFFFFFFF\n") + 1, "0x%08x\n", ++ otg_dev->os_dep.reg_offset); ++} ++ ++/** ++ * Set the register offset for the next Register Access Read/Write ++ */ ++static ssize_t regoffset_store(struct device *_dev, ++ struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ uint32_t offset = simple_strtoul(buf, NULL, 16); ++#if defined(LM_INTERFACE) || defined(PLATFORM_INTERFACE) ++ if (offset < SZ_256K) { ++#elif defined(PCI_INTERFACE) ++ if (offset < 0x00040000) { ++#endif ++ otg_dev->os_dep.reg_offset = offset; ++ } else { ++ dev_err(_dev, "invalid offset\n"); ++ } ++ ++ return count; ++} ++ ++DEVICE_ATTR(regoffset, S_IRUGO | S_IWUSR, regoffset_show, regoffset_store); ++ ++/** ++ * Show the value of the register at the offset in the reg_offset ++ * attribute. ++ */ ++static ssize_t regvalue_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ uint32_t val; ++ volatile uint32_t *addr; ++ ++ if (otg_dev->os_dep.reg_offset != 0xFFFFFFFF && 0 != otg_dev->os_dep.base) { ++ /* Calculate the address */ ++ addr = (uint32_t *) (otg_dev->os_dep.reg_offset + ++ (uint8_t *) otg_dev->os_dep.base); ++ val = DWC_READ_REG32(addr); ++ return snprintf(buf, ++ sizeof("Reg@0xFFFFFFFF = 0xFFFFFFFF\n") + 1, ++ "Reg@0x%06x = 0x%08x\n", otg_dev->os_dep.reg_offset, ++ val); ++ } else { ++ dev_err(_dev, "Invalid offset (0x%0x)\n", otg_dev->os_dep.reg_offset); ++ return sprintf(buf, "invalid offset\n"); ++ } ++} ++ ++/** ++ * Store the value in the register at the offset in the reg_offset ++ * attribute. ++ * ++ */ ++static ssize_t regvalue_store(struct device *_dev, ++ struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ volatile uint32_t *addr; ++ uint32_t val = simple_strtoul(buf, NULL, 16); ++ //dev_dbg(_dev, "Offset=0x%08x Val=0x%08x\n", otg_dev->reg_offset, val); ++ if (otg_dev->os_dep.reg_offset != 0xFFFFFFFF && 0 != otg_dev->os_dep.base) { ++ /* Calculate the address */ ++ addr = (uint32_t *) (otg_dev->os_dep.reg_offset + ++ (uint8_t *) otg_dev->os_dep.base); ++ DWC_WRITE_REG32(addr, val); ++ } else { ++ dev_err(_dev, "Invalid Register Offset (0x%08x)\n", ++ otg_dev->os_dep.reg_offset); ++ } ++ return count; ++} ++ ++DEVICE_ATTR(regvalue, S_IRUGO | S_IWUSR, regvalue_show, regvalue_store); ++ ++/* ++ * Attributes ++ */ ++DWC_OTG_DEVICE_ATTR_BITFIELD_RO(mode, "Mode"); ++DWC_OTG_DEVICE_ATTR_BITFIELD_RW(hnpcapable, "HNPCapable"); ++DWC_OTG_DEVICE_ATTR_BITFIELD_RW(srpcapable, "SRPCapable"); ++DWC_OTG_DEVICE_ATTR_BITFIELD_RW(hsic_connect, "HSIC Connect"); ++DWC_OTG_DEVICE_ATTR_BITFIELD_RW(inv_sel_hsic, "Invert Select HSIC"); ++ ++//DWC_OTG_DEVICE_ATTR_BITFIELD_RW(buspower,&(otg_dev->core_if->core_global_regs->gotgctl),(1<<8),8,"Mode"); ++//DWC_OTG_DEVICE_ATTR_BITFIELD_RW(bussuspend,&(otg_dev->core_if->core_global_regs->gotgctl),(1<<8),8,"Mode"); ++DWC_OTG_DEVICE_ATTR_BITFIELD_RO(busconnected, "Bus Connected"); ++ ++DWC_OTG_DEVICE_ATTR_REG32_RW(gotgctl, 0, "GOTGCTL"); ++DWC_OTG_DEVICE_ATTR_REG32_RW(gusbcfg, ++ &(otg_dev->core_if->core_global_regs->gusbcfg), ++ "GUSBCFG"); ++DWC_OTG_DEVICE_ATTR_REG32_RW(grxfsiz, ++ &(otg_dev->core_if->core_global_regs->grxfsiz), ++ "GRXFSIZ"); ++DWC_OTG_DEVICE_ATTR_REG32_RW(gnptxfsiz, ++ &(otg_dev->core_if->core_global_regs->gnptxfsiz), ++ "GNPTXFSIZ"); ++DWC_OTG_DEVICE_ATTR_REG32_RW(gpvndctl, ++ &(otg_dev->core_if->core_global_regs->gpvndctl), ++ "GPVNDCTL"); ++DWC_OTG_DEVICE_ATTR_REG32_RW(ggpio, ++ &(otg_dev->core_if->core_global_regs->ggpio), ++ "GGPIO"); ++DWC_OTG_DEVICE_ATTR_REG32_RW(guid, &(otg_dev->core_if->core_global_regs->guid), ++ "GUID"); ++DWC_OTG_DEVICE_ATTR_REG32_RO(gsnpsid, ++ &(otg_dev->core_if->core_global_regs->gsnpsid), ++ "GSNPSID"); ++DWC_OTG_DEVICE_ATTR_BITFIELD_RW(devspeed, "Device Speed"); ++DWC_OTG_DEVICE_ATTR_BITFIELD_RO(enumspeed, "Device Enumeration Speed"); ++ ++DWC_OTG_DEVICE_ATTR_REG32_RO(hptxfsiz, ++ &(otg_dev->core_if->core_global_regs->hptxfsiz), ++ "HPTXFSIZ"); ++DWC_OTG_DEVICE_ATTR_REG32_RW(hprt0, otg_dev->core_if->host_if->hprt0, "HPRT0"); ++ ++/** ++ * @todo Add code to initiate the HNP. ++ */ ++/** ++ * Show the HNP status bit ++ */ ++static ssize_t hnp_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ return sprintf(buf, "HstNegScs = 0x%x\n", ++ dwc_otg_get_hnpstatus(otg_dev->core_if)); ++} ++ ++/** ++ * Set the HNP Request bit ++ */ ++static ssize_t hnp_store(struct device *_dev, ++ struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ uint32_t in = simple_strtoul(buf, NULL, 16); ++ dwc_otg_set_hnpreq(otg_dev->core_if, in); ++ return count; ++} ++ ++DEVICE_ATTR(hnp, 0644, hnp_show, hnp_store); ++ ++/** ++ * @todo Add code to initiate the SRP. ++ */ ++/** ++ * Show the SRP status bit ++ */ ++static ssize_t srp_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++#ifndef DWC_HOST_ONLY ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ return sprintf(buf, "SesReqScs = 0x%x\n", ++ dwc_otg_get_srpstatus(otg_dev->core_if)); ++#else ++ return sprintf(buf, "Host Only Mode!\n"); ++#endif ++} ++ ++/** ++ * Set the SRP Request bit ++ */ ++static ssize_t srp_store(struct device *_dev, ++ struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++#ifndef DWC_HOST_ONLY ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ dwc_otg_pcd_initiate_srp(otg_dev->pcd); ++#endif ++ return count; ++} ++ ++DEVICE_ATTR(srp, 0644, srp_show, srp_store); ++ ++/** ++ * @todo Need to do more for power on/off? ++ */ ++/** ++ * Show the Bus Power status ++ */ ++static ssize_t buspower_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ return sprintf(buf, "Bus Power = 0x%x\n", ++ dwc_otg_get_prtpower(otg_dev->core_if)); ++} ++ ++/** ++ * Set the Bus Power status ++ */ ++static ssize_t buspower_store(struct device *_dev, ++ struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ uint32_t on = simple_strtoul(buf, NULL, 16); ++ dwc_otg_set_prtpower(otg_dev->core_if, on); ++ return count; ++} ++ ++DEVICE_ATTR(buspower, 0644, buspower_show, buspower_store); ++ ++/** ++ * @todo Need to do more for suspend? ++ */ ++/** ++ * Show the Bus Suspend status ++ */ ++static ssize_t bussuspend_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ return sprintf(buf, "Bus Suspend = 0x%x\n", ++ dwc_otg_get_prtsuspend(otg_dev->core_if)); ++} ++ ++/** ++ * Set the Bus Suspend status ++ */ ++static ssize_t bussuspend_store(struct device *_dev, ++ struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ uint32_t in = simple_strtoul(buf, NULL, 16); ++ dwc_otg_set_prtsuspend(otg_dev->core_if, in); ++ return count; ++} ++ ++DEVICE_ATTR(bussuspend, 0644, bussuspend_show, bussuspend_store); ++ ++/** ++ * Show the Mode Change Ready Timer status ++ */ ++static ssize_t mode_ch_tim_en_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ return sprintf(buf, "Mode Change Ready Timer Enable = 0x%x\n", ++ dwc_otg_get_mode_ch_tim(otg_dev->core_if)); ++} ++ ++/** ++ * Set the Mode Change Ready Timer status ++ */ ++static ssize_t mode_ch_tim_en_store(struct device *_dev, ++ struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ uint32_t in = simple_strtoul(buf, NULL, 16); ++ dwc_otg_set_mode_ch_tim(otg_dev->core_if, in); ++ return count; ++} ++ ++DEVICE_ATTR(mode_ch_tim_en, 0644, mode_ch_tim_en_show, mode_ch_tim_en_store); ++ ++/** ++ * Show the value of HFIR Frame Interval bitfield ++ */ ++static ssize_t fr_interval_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ return sprintf(buf, "Frame Interval = 0x%x\n", ++ dwc_otg_get_fr_interval(otg_dev->core_if)); ++} ++ ++/** ++ * Set the HFIR Frame Interval value ++ */ ++static ssize_t fr_interval_store(struct device *_dev, ++ struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ uint32_t in = simple_strtoul(buf, NULL, 10); ++ dwc_otg_set_fr_interval(otg_dev->core_if, in); ++ return count; ++} ++ ++DEVICE_ATTR(fr_interval, 0644, fr_interval_show, fr_interval_store); ++ ++/** ++ * Show the status of Remote Wakeup. ++ */ ++static ssize_t remote_wakeup_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++#ifndef DWC_HOST_ONLY ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ ++ return sprintf(buf, ++ "Remote Wakeup Sig = %d Enabled = %d LPM Remote Wakeup = %d\n", ++ dwc_otg_get_remotewakesig(otg_dev->core_if), ++ dwc_otg_pcd_get_rmwkup_enable(otg_dev->pcd), ++ dwc_otg_get_lpm_remotewakeenabled(otg_dev->core_if)); ++#else ++ return sprintf(buf, "Host Only Mode!\n"); ++#endif /* DWC_HOST_ONLY */ ++} ++ ++/** ++ * Initiate a remote wakeup of the host. The Device control register ++ * Remote Wakeup Signal bit is written if the PCD Remote wakeup enable ++ * flag is set. ++ * ++ */ ++static ssize_t remote_wakeup_store(struct device *_dev, ++ struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++#ifndef DWC_HOST_ONLY ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ uint32_t val = simple_strtoul(buf, NULL, 16); ++ ++ if (val & 1) { ++ dwc_otg_pcd_remote_wakeup(otg_dev->pcd, 1); ++ } else { ++ dwc_otg_pcd_remote_wakeup(otg_dev->pcd, 0); ++ } ++#endif /* DWC_HOST_ONLY */ ++ return count; ++} ++ ++DEVICE_ATTR(remote_wakeup, S_IRUGO | S_IWUSR, remote_wakeup_show, ++ remote_wakeup_store); ++ ++/** ++ * Show the whether core is hibernated or not. ++ */ ++static ssize_t rem_wakeup_pwrdn_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++#ifndef DWC_HOST_ONLY ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ ++ if (dwc_otg_get_core_state(otg_dev->core_if)) { ++ DWC_PRINTF("Core is in hibernation\n"); ++ } else { ++ DWC_PRINTF("Core is not in hibernation\n"); ++ } ++#endif /* DWC_HOST_ONLY */ ++ return 0; ++} ++ ++extern int dwc_otg_device_hibernation_restore(dwc_otg_core_if_t * core_if, ++ int rem_wakeup, int reset); ++ ++/** ++ * Initiate a remote wakeup of the device to exit from hibernation. ++ */ ++static ssize_t rem_wakeup_pwrdn_store(struct device *_dev, ++ struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++#ifndef DWC_HOST_ONLY ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ dwc_otg_device_hibernation_restore(otg_dev->core_if, 1, 0); ++#endif ++ return count; ++} ++ ++DEVICE_ATTR(rem_wakeup_pwrdn, S_IRUGO | S_IWUSR, rem_wakeup_pwrdn_show, ++ rem_wakeup_pwrdn_store); ++ ++static ssize_t disconnect_us(struct device *_dev, ++ struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++ ++#ifndef DWC_HOST_ONLY ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ uint32_t val = simple_strtoul(buf, NULL, 16); ++ DWC_PRINTF("The Passed value is %04x\n", val); ++ ++ dwc_otg_pcd_disconnect_us(otg_dev->pcd, 50); ++ ++#endif /* DWC_HOST_ONLY */ ++ return count; ++} ++ ++DEVICE_ATTR(disconnect_us, S_IWUSR, 0, disconnect_us); ++ ++/** ++ * Dump global registers and either host or device registers (depending on the ++ * current mode of the core). ++ */ ++static ssize_t regdump_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ ++ dwc_otg_dump_global_registers(otg_dev->core_if); ++ if (dwc_otg_is_host_mode(otg_dev->core_if)) { ++ dwc_otg_dump_host_registers(otg_dev->core_if); ++ } else { ++ dwc_otg_dump_dev_registers(otg_dev->core_if); ++ ++ } ++ return sprintf(buf, "Register Dump\n"); ++} ++ ++DEVICE_ATTR(regdump, S_IRUGO, regdump_show, 0); ++ ++/** ++ * Dump global registers and either host or device registers (depending on the ++ * current mode of the core). ++ */ ++static ssize_t spramdump_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++#if 0 ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ ++ dwc_otg_dump_spram(otg_dev->core_if); ++#endif ++ ++ return sprintf(buf, "SPRAM Dump\n"); ++} ++ ++DEVICE_ATTR(spramdump, S_IRUGO, spramdump_show, 0); ++ ++/** ++ * Dump the current hcd state. ++ */ ++static ssize_t hcddump_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++#ifndef DWC_DEVICE_ONLY ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ dwc_otg_hcd_dump_state(otg_dev->hcd); ++#endif /* DWC_DEVICE_ONLY */ ++ return sprintf(buf, "HCD Dump\n"); ++} ++ ++DEVICE_ATTR(hcddump, S_IRUGO, hcddump_show, 0); ++ ++/** ++ * Dump the average frame remaining at SOF. This can be used to ++ * determine average interrupt latency. Frame remaining is also shown for ++ * start transfer and two additional sample points. ++ */ ++static ssize_t hcd_frrem_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++#ifndef DWC_DEVICE_ONLY ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ ++ dwc_otg_hcd_dump_frrem(otg_dev->hcd); ++#endif /* DWC_DEVICE_ONLY */ ++ return sprintf(buf, "HCD Dump Frame Remaining\n"); ++} ++ ++DEVICE_ATTR(hcd_frrem, S_IRUGO, hcd_frrem_show, 0); ++ ++/** ++ * Displays the time required to read the GNPTXFSIZ register many times (the ++ * output shows the number of times the register is read). ++ */ ++#define RW_REG_COUNT 10000000 ++#define MSEC_PER_JIFFIE 1000/HZ ++static ssize_t rd_reg_test_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ int i; ++ int time; ++ int start_jiffies; ++ ++ printk("HZ %d, MSEC_PER_JIFFIE %d, loops_per_jiffy %lu\n", ++ HZ, MSEC_PER_JIFFIE, loops_per_jiffy); ++ start_jiffies = jiffies; ++ for (i = 0; i < RW_REG_COUNT; i++) { ++ dwc_otg_get_gnptxfsiz(otg_dev->core_if); ++ } ++ time = jiffies - start_jiffies; ++ return sprintf(buf, ++ "Time to read GNPTXFSIZ reg %d times: %d msecs (%d jiffies)\n", ++ RW_REG_COUNT, time * MSEC_PER_JIFFIE, time); ++} ++ ++DEVICE_ATTR(rd_reg_test, S_IRUGO, rd_reg_test_show, 0); ++ ++/** ++ * Displays the time required to write the GNPTXFSIZ register many times (the ++ * output shows the number of times the register is written). ++ */ ++static ssize_t wr_reg_test_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ uint32_t reg_val; ++ int i; ++ int time; ++ int start_jiffies; ++ ++ printk("HZ %d, MSEC_PER_JIFFIE %d, loops_per_jiffy %lu\n", ++ HZ, MSEC_PER_JIFFIE, loops_per_jiffy); ++ reg_val = dwc_otg_get_gnptxfsiz(otg_dev->core_if); ++ start_jiffies = jiffies; ++ for (i = 0; i < RW_REG_COUNT; i++) { ++ dwc_otg_set_gnptxfsiz(otg_dev->core_if, reg_val); ++ } ++ time = jiffies - start_jiffies; ++ return sprintf(buf, ++ "Time to write GNPTXFSIZ reg %d times: %d msecs (%d jiffies)\n", ++ RW_REG_COUNT, time * MSEC_PER_JIFFIE, time); ++} ++ ++DEVICE_ATTR(wr_reg_test, S_IRUGO, wr_reg_test_show, 0); ++ ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ ++/** ++* Show the lpm_response attribute. ++*/ ++static ssize_t lpmresp_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ ++ if (!dwc_otg_get_param_lpm_enable(otg_dev->core_if)) ++ return sprintf(buf, "** LPM is DISABLED **\n"); ++ ++ if (!dwc_otg_is_device_mode(otg_dev->core_if)) { ++ return sprintf(buf, "** Current mode is not device mode\n"); ++ } ++ return sprintf(buf, "lpm_response = %d\n", ++ dwc_otg_get_lpmresponse(otg_dev->core_if)); ++} ++ ++/** ++* Store the lpm_response attribute. ++*/ ++static ssize_t lpmresp_store(struct device *_dev, ++ struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ uint32_t val = simple_strtoul(buf, NULL, 16); ++ ++ if (!dwc_otg_get_param_lpm_enable(otg_dev->core_if)) { ++ return 0; ++ } ++ ++ if (!dwc_otg_is_device_mode(otg_dev->core_if)) { ++ return 0; ++ } ++ ++ dwc_otg_set_lpmresponse(otg_dev->core_if, val); ++ return count; ++} ++ ++DEVICE_ATTR(lpm_response, S_IRUGO | S_IWUSR, lpmresp_show, lpmresp_store); ++ ++/** ++* Show the sleep_status attribute. ++*/ ++static ssize_t sleepstatus_show(struct device *_dev, ++ struct device_attribute *attr, char *buf) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ return sprintf(buf, "Sleep Status = %d\n", ++ dwc_otg_get_lpm_portsleepstatus(otg_dev->core_if)); ++} ++ ++/** ++ * Store the sleep_status attribure. ++ */ ++static ssize_t sleepstatus_store(struct device *_dev, ++ struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++ dwc_otg_device_t *otg_dev = dwc_otg_drvdev(_dev); ++ dwc_otg_core_if_t *core_if = otg_dev->core_if; ++ ++ if (dwc_otg_get_lpm_portsleepstatus(otg_dev->core_if)) { ++ if (dwc_otg_is_host_mode(core_if)) { ++ ++ DWC_PRINTF("Host initiated resume\n"); ++ dwc_otg_set_prtresume(otg_dev->core_if, 1); ++ } ++ } ++ ++ return count; ++} ++ ++DEVICE_ATTR(sleep_status, S_IRUGO | S_IWUSR, sleepstatus_show, ++ sleepstatus_store); ++ ++#endif /* CONFIG_USB_DWC_OTG_LPM_ENABLE */ ++ ++/**@}*/ ++ ++/** ++ * Create the device files ++ */ ++void dwc_otg_attr_create( ++#ifdef LM_INTERFACE ++ struct lm_device *dev ++#elif defined(PCI_INTERFACE) ++ struct pci_dev *dev ++#elif defined(PLATFORM_INTERFACE) ++ struct platform_device *dev ++#endif ++ ) ++{ ++ int error; ++ ++ error = device_create_file(&dev->dev, &dev_attr_regoffset); ++ error = device_create_file(&dev->dev, &dev_attr_regvalue); ++ error = device_create_file(&dev->dev, &dev_attr_mode); ++ error = device_create_file(&dev->dev, &dev_attr_hnpcapable); ++ error = device_create_file(&dev->dev, &dev_attr_srpcapable); ++ error = device_create_file(&dev->dev, &dev_attr_hsic_connect); ++ error = device_create_file(&dev->dev, &dev_attr_inv_sel_hsic); ++ error = device_create_file(&dev->dev, &dev_attr_hnp); ++ error = device_create_file(&dev->dev, &dev_attr_srp); ++ error = device_create_file(&dev->dev, &dev_attr_buspower); ++ error = device_create_file(&dev->dev, &dev_attr_bussuspend); ++ error = device_create_file(&dev->dev, &dev_attr_mode_ch_tim_en); ++ error = device_create_file(&dev->dev, &dev_attr_fr_interval); ++ error = device_create_file(&dev->dev, &dev_attr_busconnected); ++ error = device_create_file(&dev->dev, &dev_attr_gotgctl); ++ error = device_create_file(&dev->dev, &dev_attr_gusbcfg); ++ error = device_create_file(&dev->dev, &dev_attr_grxfsiz); ++ error = device_create_file(&dev->dev, &dev_attr_gnptxfsiz); ++ error = device_create_file(&dev->dev, &dev_attr_gpvndctl); ++ error = device_create_file(&dev->dev, &dev_attr_ggpio); ++ error = device_create_file(&dev->dev, &dev_attr_guid); ++ error = device_create_file(&dev->dev, &dev_attr_gsnpsid); ++ error = device_create_file(&dev->dev, &dev_attr_devspeed); ++ error = device_create_file(&dev->dev, &dev_attr_enumspeed); ++ error = device_create_file(&dev->dev, &dev_attr_hptxfsiz); ++ error = device_create_file(&dev->dev, &dev_attr_hprt0); ++ error = device_create_file(&dev->dev, &dev_attr_remote_wakeup); ++ error = device_create_file(&dev->dev, &dev_attr_rem_wakeup_pwrdn); ++ error = device_create_file(&dev->dev, &dev_attr_disconnect_us); ++ error = device_create_file(&dev->dev, &dev_attr_regdump); ++ error = device_create_file(&dev->dev, &dev_attr_spramdump); ++ error = device_create_file(&dev->dev, &dev_attr_hcddump); ++ error = device_create_file(&dev->dev, &dev_attr_hcd_frrem); ++ error = device_create_file(&dev->dev, &dev_attr_rd_reg_test); ++ error = device_create_file(&dev->dev, &dev_attr_wr_reg_test); ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ error = device_create_file(&dev->dev, &dev_attr_lpm_response); ++ error = device_create_file(&dev->dev, &dev_attr_sleep_status); ++#endif ++} ++ ++/** ++ * Remove the device files ++ */ ++void dwc_otg_attr_remove( ++#ifdef LM_INTERFACE ++ struct lm_device *dev ++#elif defined(PCI_INTERFACE) ++ struct pci_dev *dev ++#elif defined(PLATFORM_INTERFACE) ++ struct platform_device *dev ++#endif ++ ) ++{ ++ device_remove_file(&dev->dev, &dev_attr_regoffset); ++ device_remove_file(&dev->dev, &dev_attr_regvalue); ++ device_remove_file(&dev->dev, &dev_attr_mode); ++ device_remove_file(&dev->dev, &dev_attr_hnpcapable); ++ device_remove_file(&dev->dev, &dev_attr_srpcapable); ++ device_remove_file(&dev->dev, &dev_attr_hsic_connect); ++ device_remove_file(&dev->dev, &dev_attr_inv_sel_hsic); ++ device_remove_file(&dev->dev, &dev_attr_hnp); ++ device_remove_file(&dev->dev, &dev_attr_srp); ++ device_remove_file(&dev->dev, &dev_attr_buspower); ++ device_remove_file(&dev->dev, &dev_attr_bussuspend); ++ device_remove_file(&dev->dev, &dev_attr_mode_ch_tim_en); ++ device_remove_file(&dev->dev, &dev_attr_fr_interval); ++ device_remove_file(&dev->dev, &dev_attr_busconnected); ++ device_remove_file(&dev->dev, &dev_attr_gotgctl); ++ device_remove_file(&dev->dev, &dev_attr_gusbcfg); ++ device_remove_file(&dev->dev, &dev_attr_grxfsiz); ++ device_remove_file(&dev->dev, &dev_attr_gnptxfsiz); ++ device_remove_file(&dev->dev, &dev_attr_gpvndctl); ++ device_remove_file(&dev->dev, &dev_attr_ggpio); ++ device_remove_file(&dev->dev, &dev_attr_guid); ++ device_remove_file(&dev->dev, &dev_attr_gsnpsid); ++ device_remove_file(&dev->dev, &dev_attr_devspeed); ++ device_remove_file(&dev->dev, &dev_attr_enumspeed); ++ device_remove_file(&dev->dev, &dev_attr_hptxfsiz); ++ device_remove_file(&dev->dev, &dev_attr_hprt0); ++ device_remove_file(&dev->dev, &dev_attr_remote_wakeup); ++ device_remove_file(&dev->dev, &dev_attr_rem_wakeup_pwrdn); ++ device_remove_file(&dev->dev, &dev_attr_disconnect_us); ++ device_remove_file(&dev->dev, &dev_attr_regdump); ++ device_remove_file(&dev->dev, &dev_attr_spramdump); ++ device_remove_file(&dev->dev, &dev_attr_hcddump); ++ device_remove_file(&dev->dev, &dev_attr_hcd_frrem); ++ device_remove_file(&dev->dev, &dev_attr_rd_reg_test); ++ device_remove_file(&dev->dev, &dev_attr_wr_reg_test); ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ device_remove_file(&dev->dev, &dev_attr_lpm_response); ++ device_remove_file(&dev->dev, &dev_attr_sleep_status); ++#endif ++} +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_attr.h +@@ -0,0 +1,89 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_attr.h $ ++ * $Revision: #13 $ ++ * $Date: 2010/06/21 $ ++ * $Change: 1532021 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++#if !defined(__DWC_OTG_ATTR_H__) ++#define __DWC_OTG_ATTR_H__ ++ ++/** @file ++ * This file contains the interface to the Linux device attributes. ++ */ ++extern struct device_attribute dev_attr_regoffset; ++extern struct device_attribute dev_attr_regvalue; ++ ++extern struct device_attribute dev_attr_mode; ++extern struct device_attribute dev_attr_hnpcapable; ++extern struct device_attribute dev_attr_srpcapable; ++extern struct device_attribute dev_attr_hnp; ++extern struct device_attribute dev_attr_srp; ++extern struct device_attribute dev_attr_buspower; ++extern struct device_attribute dev_attr_bussuspend; ++extern struct device_attribute dev_attr_mode_ch_tim_en; ++extern struct device_attribute dev_attr_fr_interval; ++extern struct device_attribute dev_attr_busconnected; ++extern struct device_attribute dev_attr_gotgctl; ++extern struct device_attribute dev_attr_gusbcfg; ++extern struct device_attribute dev_attr_grxfsiz; ++extern struct device_attribute dev_attr_gnptxfsiz; ++extern struct device_attribute dev_attr_gpvndctl; ++extern struct device_attribute dev_attr_ggpio; ++extern struct device_attribute dev_attr_guid; ++extern struct device_attribute dev_attr_gsnpsid; ++extern struct device_attribute dev_attr_devspeed; ++extern struct device_attribute dev_attr_enumspeed; ++extern struct device_attribute dev_attr_hptxfsiz; ++extern struct device_attribute dev_attr_hprt0; ++#ifdef CONFIG_USB_DWC_OTG_LPM ++extern struct device_attribute dev_attr_lpm_response; ++extern struct device_attribute devi_attr_sleep_status; ++#endif ++ ++void dwc_otg_attr_create( ++#ifdef LM_INTERFACE ++ struct lm_device *dev ++#elif defined(PCI_INTERFACE) ++ struct pci_dev *dev ++#elif defined(PLATFORM_INTERFACE) ++ struct platform_device *dev ++#endif ++ ); ++ ++void dwc_otg_attr_remove( ++#ifdef LM_INTERFACE ++ struct lm_device *dev ++#elif defined(PCI_INTERFACE) ++ struct pci_dev *dev ++#elif defined(PLATFORM_INTERFACE) ++ struct platform_device *dev ++#endif ++ ); ++#endif +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_cfi.c +@@ -0,0 +1,1876 @@ ++/* ========================================================================== ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++/** @file ++ * ++ * This file contains the most of the CFI(Core Feature Interface) ++ * implementation for the OTG. ++ */ ++ ++#ifdef DWC_UTE_CFI ++ ++#include "dwc_otg_pcd.h" ++#include "dwc_otg_cfi.h" ++ ++/** This definition should actually migrate to the Portability Library */ ++#define DWC_CONSTANT_CPU_TO_LE16(x) (x) ++ ++extern dwc_otg_pcd_ep_t *get_ep_by_addr(dwc_otg_pcd_t * pcd, u16 wIndex); ++ ++static int cfi_core_features_buf(uint8_t * buf, uint16_t buflen); ++static int cfi_get_feature_value(uint8_t * buf, uint16_t buflen, ++ struct dwc_otg_pcd *pcd, ++ struct cfi_usb_ctrlrequest *ctrl_req); ++static int cfi_set_feature_value(struct dwc_otg_pcd *pcd); ++static int cfi_ep_get_sg_val(uint8_t * buf, struct dwc_otg_pcd *pcd, ++ struct cfi_usb_ctrlrequest *req); ++static int cfi_ep_get_concat_val(uint8_t * buf, struct dwc_otg_pcd *pcd, ++ struct cfi_usb_ctrlrequest *req); ++static int cfi_ep_get_align_val(uint8_t * buf, struct dwc_otg_pcd *pcd, ++ struct cfi_usb_ctrlrequest *req); ++static int cfi_preproc_reset(struct dwc_otg_pcd *pcd, ++ struct cfi_usb_ctrlrequest *req); ++static void cfi_free_ep_bs_dyn_data(cfi_ep_t * cfiep); ++ ++static uint16_t get_dfifo_size(dwc_otg_core_if_t * core_if); ++static int32_t get_rxfifo_size(dwc_otg_core_if_t * core_if, uint16_t wValue); ++static int32_t get_txfifo_size(struct dwc_otg_pcd *pcd, uint16_t wValue); ++ ++static uint8_t resize_fifos(dwc_otg_core_if_t * core_if); ++ ++/** This is the header of the all features descriptor */ ++static cfi_all_features_header_t all_props_desc_header = { ++ .wVersion = DWC_CONSTANT_CPU_TO_LE16(0x100), ++ .wCoreID = DWC_CONSTANT_CPU_TO_LE16(CFI_CORE_ID_OTG), ++ .wNumFeatures = DWC_CONSTANT_CPU_TO_LE16(9), ++}; ++ ++/** This is an array of statically allocated feature descriptors */ ++static cfi_feature_desc_header_t prop_descs[] = { ++ ++ /* FT_ID_DMA_MODE */ ++ { ++ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_DMA_MODE), ++ .bmAttributes = CFI_FEATURE_ATTR_RW, ++ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(1), ++ }, ++ ++ /* FT_ID_DMA_BUFFER_SETUP */ ++ { ++ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_DMA_BUFFER_SETUP), ++ .bmAttributes = CFI_FEATURE_ATTR_RW, ++ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(6), ++ }, ++ ++ /* FT_ID_DMA_BUFF_ALIGN */ ++ { ++ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_DMA_BUFF_ALIGN), ++ .bmAttributes = CFI_FEATURE_ATTR_RW, ++ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(2), ++ }, ++ ++ /* FT_ID_DMA_CONCAT_SETUP */ ++ { ++ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_DMA_CONCAT_SETUP), ++ .bmAttributes = CFI_FEATURE_ATTR_RW, ++ //.wDataLength = DWC_CONSTANT_CPU_TO_LE16(6), ++ }, ++ ++ /* FT_ID_DMA_CIRCULAR */ ++ { ++ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_DMA_CIRCULAR), ++ .bmAttributes = CFI_FEATURE_ATTR_RW, ++ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(6), ++ }, ++ ++ /* FT_ID_THRESHOLD_SETUP */ ++ { ++ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_THRESHOLD_SETUP), ++ .bmAttributes = CFI_FEATURE_ATTR_RW, ++ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(6), ++ }, ++ ++ /* FT_ID_DFIFO_DEPTH */ ++ { ++ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_DFIFO_DEPTH), ++ .bmAttributes = CFI_FEATURE_ATTR_RO, ++ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(2), ++ }, ++ ++ /* FT_ID_TX_FIFO_DEPTH */ ++ { ++ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_TX_FIFO_DEPTH), ++ .bmAttributes = CFI_FEATURE_ATTR_RW, ++ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(2), ++ }, ++ ++ /* FT_ID_RX_FIFO_DEPTH */ ++ { ++ .wFeatureID = DWC_CONSTANT_CPU_TO_LE16(FT_ID_RX_FIFO_DEPTH), ++ .bmAttributes = CFI_FEATURE_ATTR_RW, ++ .wDataLength = DWC_CONSTANT_CPU_TO_LE16(2), ++ } ++}; ++ ++/** The table of feature names */ ++cfi_string_t prop_name_table[] = { ++ {FT_ID_DMA_MODE, "dma_mode"}, ++ {FT_ID_DMA_BUFFER_SETUP, "buffer_setup"}, ++ {FT_ID_DMA_BUFF_ALIGN, "buffer_align"}, ++ {FT_ID_DMA_CONCAT_SETUP, "concat_setup"}, ++ {FT_ID_DMA_CIRCULAR, "buffer_circular"}, ++ {FT_ID_THRESHOLD_SETUP, "threshold_setup"}, ++ {FT_ID_DFIFO_DEPTH, "dfifo_depth"}, ++ {FT_ID_TX_FIFO_DEPTH, "txfifo_depth"}, ++ {FT_ID_RX_FIFO_DEPTH, "rxfifo_depth"}, ++ {} ++}; ++ ++/************************************************************************/ ++ ++/** ++ * Returns the name of the feature by its ID ++ * or NULL if no featute ID matches. ++ * ++ */ ++const uint8_t *get_prop_name(uint16_t prop_id, int *len) ++{ ++ cfi_string_t *pstr; ++ *len = 0; ++ ++ for (pstr = prop_name_table; pstr && pstr->s; pstr++) { ++ if (pstr->id == prop_id) { ++ *len = DWC_STRLEN(pstr->s); ++ return pstr->s; ++ } ++ } ++ return NULL; ++} ++ ++/** ++ * This function handles all CFI specific control requests. ++ * ++ * Return a negative value to stall the DCE. ++ */ ++int cfi_setup(struct dwc_otg_pcd *pcd, struct cfi_usb_ctrlrequest *ctrl) ++{ ++ int retval = 0; ++ dwc_otg_pcd_ep_t *ep = NULL; ++ cfiobject_t *cfi = pcd->cfi; ++ struct dwc_otg_core_if *coreif = GET_CORE_IF(pcd); ++ uint16_t wLen = DWC_LE16_TO_CPU(&ctrl->wLength); ++ uint16_t wValue = DWC_LE16_TO_CPU(&ctrl->wValue); ++ uint16_t wIndex = DWC_LE16_TO_CPU(&ctrl->wIndex); ++ uint32_t regaddr = 0; ++ uint32_t regval = 0; ++ ++ /* Save this Control Request in the CFI object. ++ * The data field will be assigned in the data stage completion CB function. ++ */ ++ cfi->ctrl_req = *ctrl; ++ cfi->ctrl_req.data = NULL; ++ ++ cfi->need_gadget_att = 0; ++ cfi->need_status_in_complete = 0; ++ ++ switch (ctrl->bRequest) { ++ case VEN_CORE_GET_FEATURES: ++ retval = cfi_core_features_buf(cfi->buf_in.buf, CFI_IN_BUF_LEN); ++ if (retval >= 0) { ++ //dump_msg(cfi->buf_in.buf, retval); ++ ep = &pcd->ep0; ++ ++ retval = min((uint16_t) retval, wLen); ++ /* Transfer this buffer to the host through the EP0-IN EP */ ++ ep->dwc_ep.dma_addr = cfi->buf_in.addr; ++ ep->dwc_ep.start_xfer_buff = cfi->buf_in.buf; ++ ep->dwc_ep.xfer_buff = cfi->buf_in.buf; ++ ep->dwc_ep.xfer_len = retval; ++ ep->dwc_ep.xfer_count = 0; ++ ep->dwc_ep.sent_zlp = 0; ++ ep->dwc_ep.total_len = ep->dwc_ep.xfer_len; ++ ++ pcd->ep0_pending = 1; ++ dwc_otg_ep0_start_transfer(coreif, &ep->dwc_ep); ++ } ++ retval = 0; ++ break; ++ ++ case VEN_CORE_GET_FEATURE: ++ CFI_INFO("VEN_CORE_GET_FEATURE\n"); ++ retval = cfi_get_feature_value(cfi->buf_in.buf, CFI_IN_BUF_LEN, ++ pcd, ctrl); ++ if (retval >= 0) { ++ ep = &pcd->ep0; ++ ++ retval = min((uint16_t) retval, wLen); ++ /* Transfer this buffer to the host through the EP0-IN EP */ ++ ep->dwc_ep.dma_addr = cfi->buf_in.addr; ++ ep->dwc_ep.start_xfer_buff = cfi->buf_in.buf; ++ ep->dwc_ep.xfer_buff = cfi->buf_in.buf; ++ ep->dwc_ep.xfer_len = retval; ++ ep->dwc_ep.xfer_count = 0; ++ ep->dwc_ep.sent_zlp = 0; ++ ep->dwc_ep.total_len = ep->dwc_ep.xfer_len; ++ ++ pcd->ep0_pending = 1; ++ dwc_otg_ep0_start_transfer(coreif, &ep->dwc_ep); ++ } ++ CFI_INFO("VEN_CORE_GET_FEATURE=%d\n", retval); ++ dump_msg(cfi->buf_in.buf, retval); ++ break; ++ ++ case VEN_CORE_SET_FEATURE: ++ CFI_INFO("VEN_CORE_SET_FEATURE\n"); ++ /* Set up an XFER to get the data stage of the control request, ++ * which is the new value of the feature to be modified. ++ */ ++ ep = &pcd->ep0; ++ ep->dwc_ep.is_in = 0; ++ ep->dwc_ep.dma_addr = cfi->buf_out.addr; ++ ep->dwc_ep.start_xfer_buff = cfi->buf_out.buf; ++ ep->dwc_ep.xfer_buff = cfi->buf_out.buf; ++ ep->dwc_ep.xfer_len = wLen; ++ ep->dwc_ep.xfer_count = 0; ++ ep->dwc_ep.sent_zlp = 0; ++ ep->dwc_ep.total_len = ep->dwc_ep.xfer_len; ++ ++ pcd->ep0_pending = 1; ++ /* Read the control write's data stage */ ++ dwc_otg_ep0_start_transfer(coreif, &ep->dwc_ep); ++ retval = 0; ++ break; ++ ++ case VEN_CORE_RESET_FEATURES: ++ CFI_INFO("VEN_CORE_RESET_FEATURES\n"); ++ cfi->need_gadget_att = 1; ++ cfi->need_status_in_complete = 1; ++ retval = cfi_preproc_reset(pcd, ctrl); ++ CFI_INFO("VEN_CORE_RESET_FEATURES = (%d)\n", retval); ++ break; ++ ++ case VEN_CORE_ACTIVATE_FEATURES: ++ CFI_INFO("VEN_CORE_ACTIVATE_FEATURES\n"); ++ break; ++ ++ case VEN_CORE_READ_REGISTER: ++ CFI_INFO("VEN_CORE_READ_REGISTER\n"); ++ /* wValue optionally contains the HI WORD of the register offset and ++ * wIndex contains the LOW WORD of the register offset ++ */ ++ if (wValue == 0) { ++ /* @TODO - MAS - fix the access to the base field */ ++ regaddr = 0; ++ //regaddr = (uint32_t) pcd->otg_dev->os_dep.base; ++ //GET_CORE_IF(pcd)->co ++ regaddr |= wIndex; ++ } else { ++ regaddr = (wValue << 16) | wIndex; ++ } ++ ++ /* Read a 32-bit value of the memory at the regaddr */ ++ regval = DWC_READ_REG32((uint32_t *) regaddr); ++ ++ ep = &pcd->ep0; ++ dwc_memcpy(cfi->buf_in.buf, ®val, sizeof(uint32_t)); ++ ep->dwc_ep.is_in = 1; ++ ep->dwc_ep.dma_addr = cfi->buf_in.addr; ++ ep->dwc_ep.start_xfer_buff = cfi->buf_in.buf; ++ ep->dwc_ep.xfer_buff = cfi->buf_in.buf; ++ ep->dwc_ep.xfer_len = wLen; ++ ep->dwc_ep.xfer_count = 0; ++ ep->dwc_ep.sent_zlp = 0; ++ ep->dwc_ep.total_len = ep->dwc_ep.xfer_len; ++ ++ pcd->ep0_pending = 1; ++ dwc_otg_ep0_start_transfer(coreif, &ep->dwc_ep); ++ cfi->need_gadget_att = 0; ++ retval = 0; ++ break; ++ ++ case VEN_CORE_WRITE_REGISTER: ++ CFI_INFO("VEN_CORE_WRITE_REGISTER\n"); ++ /* Set up an XFER to get the data stage of the control request, ++ * which is the new value of the register to be modified. ++ */ ++ ep = &pcd->ep0; ++ ep->dwc_ep.is_in = 0; ++ ep->dwc_ep.dma_addr = cfi->buf_out.addr; ++ ep->dwc_ep.start_xfer_buff = cfi->buf_out.buf; ++ ep->dwc_ep.xfer_buff = cfi->buf_out.buf; ++ ep->dwc_ep.xfer_len = wLen; ++ ep->dwc_ep.xfer_count = 0; ++ ep->dwc_ep.sent_zlp = 0; ++ ep->dwc_ep.total_len = ep->dwc_ep.xfer_len; ++ ++ pcd->ep0_pending = 1; ++ /* Read the control write's data stage */ ++ dwc_otg_ep0_start_transfer(coreif, &ep->dwc_ep); ++ retval = 0; ++ break; ++ ++ default: ++ retval = -DWC_E_NOT_SUPPORTED; ++ break; ++ } ++ ++ return retval; ++} ++ ++/** ++ * This function prepares the core features descriptors and copies its ++ * raw representation into the buffer . ++ * ++ * The buffer structure is as follows: ++ * all_features_header (8 bytes) ++ * features_#1 (8 bytes + feature name string length) ++ * features_#2 (8 bytes + feature name string length) ++ * ..... ++ * features_#n - where n=the total count of feature descriptors ++ */ ++static int cfi_core_features_buf(uint8_t * buf, uint16_t buflen) ++{ ++ cfi_feature_desc_header_t *prop_hdr = prop_descs; ++ cfi_feature_desc_header_t *prop; ++ cfi_all_features_header_t *all_props_hdr = &all_props_desc_header; ++ cfi_all_features_header_t *tmp; ++ uint8_t *tmpbuf = buf; ++ const uint8_t *pname = NULL; ++ int i, j, namelen = 0, totlen; ++ ++ /* Prepare and copy the core features into the buffer */ ++ CFI_INFO("%s:\n", __func__); ++ ++ tmp = (cfi_all_features_header_t *) tmpbuf; ++ *tmp = *all_props_hdr; ++ tmpbuf += CFI_ALL_FEATURES_HDR_LEN; ++ ++ j = sizeof(prop_descs) / sizeof(cfi_all_features_header_t); ++ for (i = 0; i < j; i++, prop_hdr++) { ++ pname = get_prop_name(prop_hdr->wFeatureID, &namelen); ++ prop = (cfi_feature_desc_header_t *) tmpbuf; ++ *prop = *prop_hdr; ++ ++ prop->bNameLen = namelen; ++ prop->wLength = ++ DWC_CONSTANT_CPU_TO_LE16(CFI_FEATURE_DESC_HDR_LEN + ++ namelen); ++ ++ tmpbuf += CFI_FEATURE_DESC_HDR_LEN; ++ dwc_memcpy(tmpbuf, pname, namelen); ++ tmpbuf += namelen; ++ } ++ ++ totlen = tmpbuf - buf; ++ ++ if (totlen > 0) { ++ tmp = (cfi_all_features_header_t *) buf; ++ tmp->wTotalLen = DWC_CONSTANT_CPU_TO_LE16(totlen); ++ } ++ ++ return totlen; ++} ++ ++/** ++ * This function releases all the dynamic memory in the CFI object. ++ */ ++static void cfi_release(cfiobject_t * cfiobj) ++{ ++ cfi_ep_t *cfiep; ++ dwc_list_link_t *tmp; ++ ++ CFI_INFO("%s\n", __func__); ++ ++ if (cfiobj->buf_in.buf) { ++ DWC_DMA_FREE(CFI_IN_BUF_LEN, cfiobj->buf_in.buf, ++ cfiobj->buf_in.addr); ++ cfiobj->buf_in.buf = NULL; ++ } ++ ++ if (cfiobj->buf_out.buf) { ++ DWC_DMA_FREE(CFI_OUT_BUF_LEN, cfiobj->buf_out.buf, ++ cfiobj->buf_out.addr); ++ cfiobj->buf_out.buf = NULL; ++ } ++ ++ /* Free the Buffer Setup values for each EP */ ++ //list_for_each_entry(cfiep, &cfiobj->active_eps, lh) { ++ DWC_LIST_FOREACH(tmp, &cfiobj->active_eps) { ++ cfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh); ++ cfi_free_ep_bs_dyn_data(cfiep); ++ } ++} ++ ++/** ++ * This function frees the dynamically allocated EP buffer setup data. ++ */ ++static void cfi_free_ep_bs_dyn_data(cfi_ep_t * cfiep) ++{ ++ if (cfiep->bm_sg) { ++ DWC_FREE(cfiep->bm_sg); ++ cfiep->bm_sg = NULL; ++ } ++ ++ if (cfiep->bm_align) { ++ DWC_FREE(cfiep->bm_align); ++ cfiep->bm_align = NULL; ++ } ++ ++ if (cfiep->bm_concat) { ++ if (NULL != cfiep->bm_concat->wTxBytes) { ++ DWC_FREE(cfiep->bm_concat->wTxBytes); ++ cfiep->bm_concat->wTxBytes = NULL; ++ } ++ DWC_FREE(cfiep->bm_concat); ++ cfiep->bm_concat = NULL; ++ } ++} ++ ++/** ++ * This function initializes the default values of the features ++ * for a specific endpoint and should be called only once when ++ * the EP is enabled first time. ++ */ ++static int cfi_ep_init_defaults(struct dwc_otg_pcd *pcd, cfi_ep_t * cfiep) ++{ ++ int retval = 0; ++ ++ cfiep->bm_sg = DWC_ALLOC(sizeof(ddma_sg_buffer_setup_t)); ++ if (NULL == cfiep->bm_sg) { ++ CFI_INFO("Failed to allocate memory for SG feature value\n"); ++ return -DWC_E_NO_MEMORY; ++ } ++ dwc_memset(cfiep->bm_sg, 0, sizeof(ddma_sg_buffer_setup_t)); ++ ++ /* For the Concatenation feature's default value we do not allocate ++ * memory for the wTxBytes field - it will be done in the set_feature_value ++ * request handler. ++ */ ++ cfiep->bm_concat = DWC_ALLOC(sizeof(ddma_concat_buffer_setup_t)); ++ if (NULL == cfiep->bm_concat) { ++ CFI_INFO ++ ("Failed to allocate memory for CONCATENATION feature value\n"); ++ DWC_FREE(cfiep->bm_sg); ++ return -DWC_E_NO_MEMORY; ++ } ++ dwc_memset(cfiep->bm_concat, 0, sizeof(ddma_concat_buffer_setup_t)); ++ ++ cfiep->bm_align = DWC_ALLOC(sizeof(ddma_align_buffer_setup_t)); ++ if (NULL == cfiep->bm_align) { ++ CFI_INFO ++ ("Failed to allocate memory for Alignment feature value\n"); ++ DWC_FREE(cfiep->bm_sg); ++ DWC_FREE(cfiep->bm_concat); ++ return -DWC_E_NO_MEMORY; ++ } ++ dwc_memset(cfiep->bm_align, 0, sizeof(ddma_align_buffer_setup_t)); ++ ++ return retval; ++} ++ ++/** ++ * The callback function that notifies the CFI on the activation of ++ * an endpoint in the PCD. The following steps are done in this function: ++ * ++ * Create a dynamically allocated cfi_ep_t object (a CFI wrapper to the PCD's ++ * active endpoint) ++ * Create MAX_DMA_DESCS_PER_EP count DMA Descriptors for the EP ++ * Set the Buffer Mode to standard ++ * Initialize the default values for all EP modes (SG, Circular, Concat, Align) ++ * Add the cfi_ep_t object to the list of active endpoints in the CFI object ++ */ ++static int cfi_ep_enable(struct cfiobject *cfi, struct dwc_otg_pcd *pcd, ++ struct dwc_otg_pcd_ep *ep) ++{ ++ cfi_ep_t *cfiep; ++ int retval = -DWC_E_NOT_SUPPORTED; ++ ++ CFI_INFO("%s: epname=%s; epnum=0x%02x\n", __func__, ++ "EP_" /*ep->ep.name */ , ep->desc->bEndpointAddress); ++ /* MAS - Check whether this endpoint already is in the list */ ++ cfiep = get_cfi_ep_by_pcd_ep(cfi, ep); ++ ++ if (NULL == cfiep) { ++ /* Allocate a cfi_ep_t object */ ++ cfiep = DWC_ALLOC(sizeof(cfi_ep_t)); ++ if (NULL == cfiep) { ++ CFI_INFO ++ ("Unable to allocate memory for in function %s\n", ++ __func__); ++ return -DWC_E_NO_MEMORY; ++ } ++ dwc_memset(cfiep, 0, sizeof(cfi_ep_t)); ++ ++ /* Save the dwc_otg_pcd_ep pointer in the cfiep object */ ++ cfiep->ep = ep; ++ ++ /* Allocate the DMA Descriptors chain of MAX_DMA_DESCS_PER_EP count */ ++ ep->dwc_ep.descs = ++ DWC_DMA_ALLOC(MAX_DMA_DESCS_PER_EP * ++ sizeof(dwc_otg_dma_desc_t), ++ &ep->dwc_ep.descs_dma_addr); ++ ++ if (NULL == ep->dwc_ep.descs) { ++ DWC_FREE(cfiep); ++ return -DWC_E_NO_MEMORY; ++ } ++ ++ DWC_LIST_INIT(&cfiep->lh); ++ ++ /* Set the buffer mode to BM_STANDARD. It will be modified ++ * when building descriptors for a specific buffer mode */ ++ ep->dwc_ep.buff_mode = BM_STANDARD; ++ ++ /* Create and initialize the default values for this EP's Buffer modes */ ++ if ((retval = cfi_ep_init_defaults(pcd, cfiep)) < 0) ++ return retval; ++ ++ /* Add the cfi_ep_t object to the CFI object's list of active endpoints */ ++ DWC_LIST_INSERT_TAIL(&cfi->active_eps, &cfiep->lh); ++ retval = 0; ++ } else { /* The sought EP already is in the list */ ++ CFI_INFO("%s: The sought EP already is in the list\n", ++ __func__); ++ } ++ ++ return retval; ++} ++ ++/** ++ * This function is called when the data stage of a 3-stage Control Write request ++ * is complete. ++ * ++ */ ++static int cfi_ctrl_write_complete(struct cfiobject *cfi, ++ struct dwc_otg_pcd *pcd) ++{ ++ uint32_t addr, reg_value; ++ uint16_t wIndex, wValue; ++ uint8_t bRequest; ++ uint8_t *buf = cfi->buf_out.buf; ++ //struct usb_ctrlrequest *ctrl_req = &cfi->ctrl_req_saved; ++ struct cfi_usb_ctrlrequest *ctrl_req = &cfi->ctrl_req; ++ int retval = -DWC_E_NOT_SUPPORTED; ++ ++ CFI_INFO("%s\n", __func__); ++ ++ bRequest = ctrl_req->bRequest; ++ wIndex = DWC_CONSTANT_CPU_TO_LE16(ctrl_req->wIndex); ++ wValue = DWC_CONSTANT_CPU_TO_LE16(ctrl_req->wValue); ++ ++ /* ++ * Save the pointer to the data stage in the ctrl_req's field. ++ * The request should be already saved in the command stage by now. ++ */ ++ ctrl_req->data = cfi->buf_out.buf; ++ cfi->need_status_in_complete = 0; ++ cfi->need_gadget_att = 0; ++ ++ switch (bRequest) { ++ case VEN_CORE_WRITE_REGISTER: ++ /* The buffer contains raw data of the new value for the register */ ++ reg_value = *((uint32_t *) buf); ++ if (wValue == 0) { ++ addr = 0; ++ //addr = (uint32_t) pcd->otg_dev->os_dep.base; ++ addr += wIndex; ++ } else { ++ addr = (wValue << 16) | wIndex; ++ } ++ ++ //writel(reg_value, addr); ++ ++ retval = 0; ++ cfi->need_status_in_complete = 1; ++ break; ++ ++ case VEN_CORE_SET_FEATURE: ++ /* The buffer contains raw data of the new value of the feature */ ++ retval = cfi_set_feature_value(pcd); ++ if (retval < 0) ++ return retval; ++ ++ cfi->need_status_in_complete = 1; ++ break; ++ ++ default: ++ break; ++ } ++ ++ return retval; ++} ++ ++/** ++ * This function builds the DMA descriptors for the SG buffer mode. ++ */ ++static void cfi_build_sg_descs(struct cfiobject *cfi, cfi_ep_t * cfiep, ++ dwc_otg_pcd_request_t * req) ++{ ++ struct dwc_otg_pcd_ep *ep = cfiep->ep; ++ ddma_sg_buffer_setup_t *sgval = cfiep->bm_sg; ++ struct dwc_otg_dma_desc *desc = cfiep->ep->dwc_ep.descs; ++ struct dwc_otg_dma_desc *desc_last = cfiep->ep->dwc_ep.descs; ++ dma_addr_t buff_addr = req->dma; ++ int i; ++ uint32_t txsize, off; ++ ++ txsize = sgval->wSize; ++ off = sgval->bOffset; ++ ++// CFI_INFO("%s: %s TXSIZE=0x%08x; OFFSET=0x%08x\n", ++// __func__, cfiep->ep->ep.name, txsize, off); ++ ++ for (i = 0; i < sgval->bCount; i++) { ++ desc->status.b.bs = BS_HOST_BUSY; ++ desc->buf = buff_addr; ++ desc->status.b.l = 0; ++ desc->status.b.ioc = 0; ++ desc->status.b.sp = 0; ++ desc->status.b.bytes = txsize; ++ desc->status.b.bs = BS_HOST_READY; ++ ++ /* Set the next address of the buffer */ ++ buff_addr += txsize + off; ++ desc_last = desc; ++ desc++; ++ } ++ ++ /* Set the last, ioc and sp bits on the Last DMA Descriptor */ ++ desc_last->status.b.l = 1; ++ desc_last->status.b.ioc = 1; ++ desc_last->status.b.sp = ep->dwc_ep.sent_zlp; ++ /* Save the last DMA descriptor pointer */ ++ cfiep->dma_desc_last = desc_last; ++ cfiep->desc_count = sgval->bCount; ++} ++ ++/** ++ * This function builds the DMA descriptors for the Concatenation buffer mode. ++ */ ++static void cfi_build_concat_descs(struct cfiobject *cfi, cfi_ep_t * cfiep, ++ dwc_otg_pcd_request_t * req) ++{ ++ struct dwc_otg_pcd_ep *ep = cfiep->ep; ++ ddma_concat_buffer_setup_t *concatval = cfiep->bm_concat; ++ struct dwc_otg_dma_desc *desc = cfiep->ep->dwc_ep.descs; ++ struct dwc_otg_dma_desc *desc_last = cfiep->ep->dwc_ep.descs; ++ dma_addr_t buff_addr = req->dma; ++ int i; ++ uint16_t *txsize; ++ ++ txsize = concatval->wTxBytes; ++ ++ for (i = 0; i < concatval->hdr.bDescCount; i++) { ++ desc->buf = buff_addr; ++ desc->status.b.bs = BS_HOST_BUSY; ++ desc->status.b.l = 0; ++ desc->status.b.ioc = 0; ++ desc->status.b.sp = 0; ++ desc->status.b.bytes = *txsize; ++ desc->status.b.bs = BS_HOST_READY; ++ ++ txsize++; ++ /* Set the next address of the buffer */ ++ buff_addr += UGETW(ep->desc->wMaxPacketSize); ++ desc_last = desc; ++ desc++; ++ } ++ ++ /* Set the last, ioc and sp bits on the Last DMA Descriptor */ ++ desc_last->status.b.l = 1; ++ desc_last->status.b.ioc = 1; ++ desc_last->status.b.sp = ep->dwc_ep.sent_zlp; ++ cfiep->dma_desc_last = desc_last; ++ cfiep->desc_count = concatval->hdr.bDescCount; ++} ++ ++/** ++ * This function builds the DMA descriptors for the Circular buffer mode ++ */ ++static void cfi_build_circ_descs(struct cfiobject *cfi, cfi_ep_t * cfiep, ++ dwc_otg_pcd_request_t * req) ++{ ++ /* @todo: MAS - add implementation when this feature needs to be tested */ ++} ++ ++/** ++ * This function builds the DMA descriptors for the Alignment buffer mode ++ */ ++static void cfi_build_align_descs(struct cfiobject *cfi, cfi_ep_t * cfiep, ++ dwc_otg_pcd_request_t * req) ++{ ++ struct dwc_otg_pcd_ep *ep = cfiep->ep; ++ ddma_align_buffer_setup_t *alignval = cfiep->bm_align; ++ struct dwc_otg_dma_desc *desc = cfiep->ep->dwc_ep.descs; ++ dma_addr_t buff_addr = req->dma; ++ ++ desc->status.b.bs = BS_HOST_BUSY; ++ desc->status.b.l = 1; ++ desc->status.b.ioc = 1; ++ desc->status.b.sp = ep->dwc_ep.sent_zlp; ++ desc->status.b.bytes = req->length; ++ /* Adjust the buffer alignment */ ++ desc->buf = (buff_addr + alignval->bAlign); ++ desc->status.b.bs = BS_HOST_READY; ++ cfiep->dma_desc_last = desc; ++ cfiep->desc_count = 1; ++} ++ ++/** ++ * This function builds the DMA descriptors chain for different modes of the ++ * buffer setup of an endpoint. ++ */ ++static void cfi_build_descriptors(struct cfiobject *cfi, ++ struct dwc_otg_pcd *pcd, ++ struct dwc_otg_pcd_ep *ep, ++ dwc_otg_pcd_request_t * req) ++{ ++ cfi_ep_t *cfiep; ++ ++ /* Get the cfiep by the dwc_otg_pcd_ep */ ++ cfiep = get_cfi_ep_by_pcd_ep(cfi, ep); ++ if (NULL == cfiep) { ++ CFI_INFO("%s: Unable to find a matching active endpoint\n", ++ __func__); ++ return; ++ } ++ ++ cfiep->xfer_len = req->length; ++ ++ /* Iterate through all the DMA descriptors */ ++ switch (cfiep->ep->dwc_ep.buff_mode) { ++ case BM_SG: ++ cfi_build_sg_descs(cfi, cfiep, req); ++ break; ++ ++ case BM_CONCAT: ++ cfi_build_concat_descs(cfi, cfiep, req); ++ break; ++ ++ case BM_CIRCULAR: ++ cfi_build_circ_descs(cfi, cfiep, req); ++ break; ++ ++ case BM_ALIGN: ++ cfi_build_align_descs(cfi, cfiep, req); ++ break; ++ ++ default: ++ break; ++ } ++} ++ ++/** ++ * Allocate DMA buffer for different Buffer modes. ++ */ ++static void *cfi_ep_alloc_buf(struct cfiobject *cfi, struct dwc_otg_pcd *pcd, ++ struct dwc_otg_pcd_ep *ep, dma_addr_t * dma, ++ unsigned size, gfp_t flags) ++{ ++ return DWC_DMA_ALLOC(size, dma); ++} ++ ++/** ++ * This function initializes the CFI object. ++ */ ++int init_cfi(cfiobject_t * cfiobj) ++{ ++ CFI_INFO("%s\n", __func__); ++ ++ /* Allocate a buffer for IN XFERs */ ++ cfiobj->buf_in.buf = ++ DWC_DMA_ALLOC(CFI_IN_BUF_LEN, &cfiobj->buf_in.addr); ++ if (NULL == cfiobj->buf_in.buf) { ++ CFI_INFO("Unable to allocate buffer for INs\n"); ++ return -DWC_E_NO_MEMORY; ++ } ++ ++ /* Allocate a buffer for OUT XFERs */ ++ cfiobj->buf_out.buf = ++ DWC_DMA_ALLOC(CFI_OUT_BUF_LEN, &cfiobj->buf_out.addr); ++ if (NULL == cfiobj->buf_out.buf) { ++ CFI_INFO("Unable to allocate buffer for OUT\n"); ++ return -DWC_E_NO_MEMORY; ++ } ++ ++ /* Initialize the callback function pointers */ ++ cfiobj->ops.release = cfi_release; ++ cfiobj->ops.ep_enable = cfi_ep_enable; ++ cfiobj->ops.ctrl_write_complete = cfi_ctrl_write_complete; ++ cfiobj->ops.build_descriptors = cfi_build_descriptors; ++ cfiobj->ops.ep_alloc_buf = cfi_ep_alloc_buf; ++ ++ /* Initialize the list of active endpoints in the CFI object */ ++ DWC_LIST_INIT(&cfiobj->active_eps); ++ ++ return 0; ++} ++ ++/** ++ * This function reads the required feature's current value into the buffer ++ * ++ * @retval: Returns negative as error, or the data length of the feature ++ */ ++static int cfi_get_feature_value(uint8_t * buf, uint16_t buflen, ++ struct dwc_otg_pcd *pcd, ++ struct cfi_usb_ctrlrequest *ctrl_req) ++{ ++ int retval = -DWC_E_NOT_SUPPORTED; ++ struct dwc_otg_core_if *coreif = GET_CORE_IF(pcd); ++ uint16_t dfifo, rxfifo, txfifo; ++ ++ switch (ctrl_req->wIndex) { ++ /* Whether the DDMA is enabled or not */ ++ case FT_ID_DMA_MODE: ++ *buf = (coreif->dma_enable && coreif->dma_desc_enable) ? 1 : 0; ++ retval = 1; ++ break; ++ ++ case FT_ID_DMA_BUFFER_SETUP: ++ retval = cfi_ep_get_sg_val(buf, pcd, ctrl_req); ++ break; ++ ++ case FT_ID_DMA_BUFF_ALIGN: ++ retval = cfi_ep_get_align_val(buf, pcd, ctrl_req); ++ break; ++ ++ case FT_ID_DMA_CONCAT_SETUP: ++ retval = cfi_ep_get_concat_val(buf, pcd, ctrl_req); ++ break; ++ ++ case FT_ID_DMA_CIRCULAR: ++ CFI_INFO("GetFeature value (FT_ID_DMA_CIRCULAR)\n"); ++ break; ++ ++ case FT_ID_THRESHOLD_SETUP: ++ CFI_INFO("GetFeature value (FT_ID_THRESHOLD_SETUP)\n"); ++ break; ++ ++ case FT_ID_DFIFO_DEPTH: ++ dfifo = get_dfifo_size(coreif); ++ *((uint16_t *) buf) = dfifo; ++ retval = sizeof(uint16_t); ++ break; ++ ++ case FT_ID_TX_FIFO_DEPTH: ++ retval = get_txfifo_size(pcd, ctrl_req->wValue); ++ if (retval >= 0) { ++ txfifo = retval; ++ *((uint16_t *) buf) = txfifo; ++ retval = sizeof(uint16_t); ++ } ++ break; ++ ++ case FT_ID_RX_FIFO_DEPTH: ++ retval = get_rxfifo_size(coreif, ctrl_req->wValue); ++ if (retval >= 0) { ++ rxfifo = retval; ++ *((uint16_t *) buf) = rxfifo; ++ retval = sizeof(uint16_t); ++ } ++ break; ++ } ++ ++ return retval; ++} ++ ++/** ++ * This function resets the SG for the specified EP to its default value ++ */ ++static int cfi_reset_sg_val(cfi_ep_t * cfiep) ++{ ++ dwc_memset(cfiep->bm_sg, 0, sizeof(ddma_sg_buffer_setup_t)); ++ return 0; ++} ++ ++/** ++ * This function resets the Alignment for the specified EP to its default value ++ */ ++static int cfi_reset_align_val(cfi_ep_t * cfiep) ++{ ++ dwc_memset(cfiep->bm_sg, 0, sizeof(ddma_sg_buffer_setup_t)); ++ return 0; ++} ++ ++/** ++ * This function resets the Concatenation for the specified EP to its default value ++ * This function will also set the value of the wTxBytes field to NULL after ++ * freeing the memory previously allocated for this field. ++ */ ++static int cfi_reset_concat_val(cfi_ep_t * cfiep) ++{ ++ /* First we need to free the wTxBytes field */ ++ if (cfiep->bm_concat->wTxBytes) { ++ DWC_FREE(cfiep->bm_concat->wTxBytes); ++ cfiep->bm_concat->wTxBytes = NULL; ++ } ++ ++ dwc_memset(cfiep->bm_concat, 0, sizeof(ddma_concat_buffer_setup_t)); ++ return 0; ++} ++ ++/** ++ * This function resets all the buffer setups of the specified endpoint ++ */ ++static int cfi_ep_reset_all_setup_vals(cfi_ep_t * cfiep) ++{ ++ cfi_reset_sg_val(cfiep); ++ cfi_reset_align_val(cfiep); ++ cfi_reset_concat_val(cfiep); ++ return 0; ++} ++ ++static int cfi_handle_reset_fifo_val(struct dwc_otg_pcd *pcd, uint8_t ep_addr, ++ uint8_t rx_rst, uint8_t tx_rst) ++{ ++ int retval = -DWC_E_INVALID; ++ uint16_t tx_siz[15]; ++ uint16_t rx_siz = 0; ++ dwc_otg_pcd_ep_t *ep = NULL; ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dwc_otg_core_params_t *params = GET_CORE_IF(pcd)->core_params; ++ ++ if (rx_rst) { ++ rx_siz = params->dev_rx_fifo_size; ++ params->dev_rx_fifo_size = GET_CORE_IF(pcd)->init_rxfsiz; ++ } ++ ++ if (tx_rst) { ++ if (ep_addr == 0) { ++ int i; ++ ++ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) { ++ tx_siz[i] = ++ core_if->core_params->dev_tx_fifo_size[i]; ++ core_if->core_params->dev_tx_fifo_size[i] = ++ core_if->init_txfsiz[i]; ++ } ++ } else { ++ ++ ep = get_ep_by_addr(pcd, ep_addr); ++ ++ if (NULL == ep) { ++ CFI_INFO ++ ("%s: Unable to get the endpoint addr=0x%02x\n", ++ __func__, ep_addr); ++ return -DWC_E_INVALID; ++ } ++ ++ tx_siz[0] = ++ params->dev_tx_fifo_size[ep->dwc_ep.tx_fifo_num - ++ 1]; ++ params->dev_tx_fifo_size[ep->dwc_ep.tx_fifo_num - 1] = ++ GET_CORE_IF(pcd)->init_txfsiz[ep-> ++ dwc_ep.tx_fifo_num - ++ 1]; ++ } ++ } ++ ++ if (resize_fifos(GET_CORE_IF(pcd))) { ++ retval = 0; ++ } else { ++ CFI_INFO ++ ("%s: Error resetting the feature Reset All(FIFO size)\n", ++ __func__); ++ if (rx_rst) { ++ params->dev_rx_fifo_size = rx_siz; ++ } ++ ++ if (tx_rst) { ++ if (ep_addr == 0) { ++ int i; ++ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; ++ i++) { ++ core_if-> ++ core_params->dev_tx_fifo_size[i] = ++ tx_siz[i]; ++ } ++ } else { ++ params->dev_tx_fifo_size[ep-> ++ dwc_ep.tx_fifo_num - ++ 1] = tx_siz[0]; ++ } ++ } ++ retval = -DWC_E_INVALID; ++ } ++ return retval; ++} ++ ++static int cfi_handle_reset_all(struct dwc_otg_pcd *pcd, uint8_t addr) ++{ ++ int retval = 0; ++ cfi_ep_t *cfiep; ++ cfiobject_t *cfi = pcd->cfi; ++ dwc_list_link_t *tmp; ++ ++ retval = cfi_handle_reset_fifo_val(pcd, addr, 1, 1); ++ if (retval < 0) { ++ return retval; ++ } ++ ++ /* If the EP address is known then reset the features for only that EP */ ++ if (addr) { ++ cfiep = get_cfi_ep_by_addr(pcd->cfi, addr); ++ if (NULL == cfiep) { ++ CFI_INFO("%s: Error getting the EP address 0x%02x\n", ++ __func__, addr); ++ return -DWC_E_INVALID; ++ } ++ retval = cfi_ep_reset_all_setup_vals(cfiep); ++ cfiep->ep->dwc_ep.buff_mode = BM_STANDARD; ++ } ++ /* Otherwise (wValue == 0), reset all features of all EP's */ ++ else { ++ /* Traverse all the active EP's and reset the feature(s) value(s) */ ++ //list_for_each_entry(cfiep, &cfi->active_eps, lh) { ++ DWC_LIST_FOREACH(tmp, &cfi->active_eps) { ++ cfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh); ++ retval = cfi_ep_reset_all_setup_vals(cfiep); ++ cfiep->ep->dwc_ep.buff_mode = BM_STANDARD; ++ if (retval < 0) { ++ CFI_INFO ++ ("%s: Error resetting the feature Reset All\n", ++ __func__); ++ return retval; ++ } ++ } ++ } ++ return retval; ++} ++ ++static int cfi_handle_reset_dma_buff_setup(struct dwc_otg_pcd *pcd, ++ uint8_t addr) ++{ ++ int retval = 0; ++ cfi_ep_t *cfiep; ++ cfiobject_t *cfi = pcd->cfi; ++ dwc_list_link_t *tmp; ++ ++ /* If the EP address is known then reset the features for only that EP */ ++ if (addr) { ++ cfiep = get_cfi_ep_by_addr(pcd->cfi, addr); ++ if (NULL == cfiep) { ++ CFI_INFO("%s: Error getting the EP address 0x%02x\n", ++ __func__, addr); ++ return -DWC_E_INVALID; ++ } ++ retval = cfi_reset_sg_val(cfiep); ++ } ++ /* Otherwise (wValue == 0), reset all features of all EP's */ ++ else { ++ /* Traverse all the active EP's and reset the feature(s) value(s) */ ++ //list_for_each_entry(cfiep, &cfi->active_eps, lh) { ++ DWC_LIST_FOREACH(tmp, &cfi->active_eps) { ++ cfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh); ++ retval = cfi_reset_sg_val(cfiep); ++ if (retval < 0) { ++ CFI_INFO ++ ("%s: Error resetting the feature Buffer Setup\n", ++ __func__); ++ return retval; ++ } ++ } ++ } ++ return retval; ++} ++ ++static int cfi_handle_reset_concat_val(struct dwc_otg_pcd *pcd, uint8_t addr) ++{ ++ int retval = 0; ++ cfi_ep_t *cfiep; ++ cfiobject_t *cfi = pcd->cfi; ++ dwc_list_link_t *tmp; ++ ++ /* If the EP address is known then reset the features for only that EP */ ++ if (addr) { ++ cfiep = get_cfi_ep_by_addr(pcd->cfi, addr); ++ if (NULL == cfiep) { ++ CFI_INFO("%s: Error getting the EP address 0x%02x\n", ++ __func__, addr); ++ return -DWC_E_INVALID; ++ } ++ retval = cfi_reset_concat_val(cfiep); ++ } ++ /* Otherwise (wValue == 0), reset all features of all EP's */ ++ else { ++ /* Traverse all the active EP's and reset the feature(s) value(s) */ ++ //list_for_each_entry(cfiep, &cfi->active_eps, lh) { ++ DWC_LIST_FOREACH(tmp, &cfi->active_eps) { ++ cfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh); ++ retval = cfi_reset_concat_val(cfiep); ++ if (retval < 0) { ++ CFI_INFO ++ ("%s: Error resetting the feature Concatenation Value\n", ++ __func__); ++ return retval; ++ } ++ } ++ } ++ return retval; ++} ++ ++static int cfi_handle_reset_align_val(struct dwc_otg_pcd *pcd, uint8_t addr) ++{ ++ int retval = 0; ++ cfi_ep_t *cfiep; ++ cfiobject_t *cfi = pcd->cfi; ++ dwc_list_link_t *tmp; ++ ++ /* If the EP address is known then reset the features for only that EP */ ++ if (addr) { ++ cfiep = get_cfi_ep_by_addr(pcd->cfi, addr); ++ if (NULL == cfiep) { ++ CFI_INFO("%s: Error getting the EP address 0x%02x\n", ++ __func__, addr); ++ return -DWC_E_INVALID; ++ } ++ retval = cfi_reset_align_val(cfiep); ++ } ++ /* Otherwise (wValue == 0), reset all features of all EP's */ ++ else { ++ /* Traverse all the active EP's and reset the feature(s) value(s) */ ++ //list_for_each_entry(cfiep, &cfi->active_eps, lh) { ++ DWC_LIST_FOREACH(tmp, &cfi->active_eps) { ++ cfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh); ++ retval = cfi_reset_align_val(cfiep); ++ if (retval < 0) { ++ CFI_INFO ++ ("%s: Error resetting the feature Aliignment Value\n", ++ __func__); ++ return retval; ++ } ++ } ++ } ++ return retval; ++ ++} ++ ++static int cfi_preproc_reset(struct dwc_otg_pcd *pcd, ++ struct cfi_usb_ctrlrequest *req) ++{ ++ int retval = 0; ++ ++ switch (req->wIndex) { ++ case 0: ++ /* Reset all features */ ++ retval = cfi_handle_reset_all(pcd, req->wValue & 0xff); ++ break; ++ ++ case FT_ID_DMA_BUFFER_SETUP: ++ /* Reset the SG buffer setup */ ++ retval = ++ cfi_handle_reset_dma_buff_setup(pcd, req->wValue & 0xff); ++ break; ++ ++ case FT_ID_DMA_CONCAT_SETUP: ++ /* Reset the Concatenation buffer setup */ ++ retval = cfi_handle_reset_concat_val(pcd, req->wValue & 0xff); ++ break; ++ ++ case FT_ID_DMA_BUFF_ALIGN: ++ /* Reset the Alignment buffer setup */ ++ retval = cfi_handle_reset_align_val(pcd, req->wValue & 0xff); ++ break; ++ ++ case FT_ID_TX_FIFO_DEPTH: ++ retval = ++ cfi_handle_reset_fifo_val(pcd, req->wValue & 0xff, 0, 1); ++ pcd->cfi->need_gadget_att = 0; ++ break; ++ ++ case FT_ID_RX_FIFO_DEPTH: ++ retval = cfi_handle_reset_fifo_val(pcd, 0, 1, 0); ++ pcd->cfi->need_gadget_att = 0; ++ break; ++ default: ++ break; ++ } ++ return retval; ++} ++ ++/** ++ * This function sets a new value for the SG buffer setup. ++ */ ++static int cfi_ep_set_sg_val(uint8_t * buf, struct dwc_otg_pcd *pcd) ++{ ++ uint8_t inaddr, outaddr; ++ cfi_ep_t *epin, *epout; ++ ddma_sg_buffer_setup_t *psgval; ++ uint32_t desccount, size; ++ ++ CFI_INFO("%s\n", __func__); ++ ++ psgval = (ddma_sg_buffer_setup_t *) buf; ++ desccount = (uint32_t) psgval->bCount; ++ size = (uint32_t) psgval->wSize; ++ ++ /* Check the DMA descriptor count */ ++ if ((desccount > MAX_DMA_DESCS_PER_EP) || (desccount == 0)) { ++ CFI_INFO ++ ("%s: The count of DMA Descriptors should be between 1 and %d\n", ++ __func__, MAX_DMA_DESCS_PER_EP); ++ return -DWC_E_INVALID; ++ } ++ ++ /* Check the DMA descriptor count */ ++ ++ if (size == 0) { ++ ++ CFI_INFO("%s: The transfer size should be at least 1 byte\n", ++ __func__); ++ ++ return -DWC_E_INVALID; ++ ++ } ++ ++ inaddr = psgval->bInEndpointAddress; ++ outaddr = psgval->bOutEndpointAddress; ++ ++ epin = get_cfi_ep_by_addr(pcd->cfi, inaddr); ++ epout = get_cfi_ep_by_addr(pcd->cfi, outaddr); ++ ++ if (NULL == epin || NULL == epout) { ++ CFI_INFO ++ ("%s: Unable to get the endpoints inaddr=0x%02x outaddr=0x%02x\n", ++ __func__, inaddr, outaddr); ++ return -DWC_E_INVALID; ++ } ++ ++ epin->ep->dwc_ep.buff_mode = BM_SG; ++ dwc_memcpy(epin->bm_sg, psgval, sizeof(ddma_sg_buffer_setup_t)); ++ ++ epout->ep->dwc_ep.buff_mode = BM_SG; ++ dwc_memcpy(epout->bm_sg, psgval, sizeof(ddma_sg_buffer_setup_t)); ++ ++ return 0; ++} ++ ++/** ++ * This function sets a new value for the buffer Alignment setup. ++ */ ++static int cfi_ep_set_alignment_val(uint8_t * buf, struct dwc_otg_pcd *pcd) ++{ ++ cfi_ep_t *ep; ++ uint8_t addr; ++ ddma_align_buffer_setup_t *palignval; ++ ++ palignval = (ddma_align_buffer_setup_t *) buf; ++ addr = palignval->bEndpointAddress; ++ ++ ep = get_cfi_ep_by_addr(pcd->cfi, addr); ++ ++ if (NULL == ep) { ++ CFI_INFO("%s: Unable to get the endpoint addr=0x%02x\n", ++ __func__, addr); ++ return -DWC_E_INVALID; ++ } ++ ++ ep->ep->dwc_ep.buff_mode = BM_ALIGN; ++ dwc_memcpy(ep->bm_align, palignval, sizeof(ddma_align_buffer_setup_t)); ++ ++ return 0; ++} ++ ++/** ++ * This function sets a new value for the Concatenation buffer setup. ++ */ ++static int cfi_ep_set_concat_val(uint8_t * buf, struct dwc_otg_pcd *pcd) ++{ ++ uint8_t addr; ++ cfi_ep_t *ep; ++ struct _ddma_concat_buffer_setup_hdr *pConcatValHdr; ++ uint16_t *pVals; ++ uint32_t desccount; ++ int i; ++ uint16_t mps; ++ ++ pConcatValHdr = (struct _ddma_concat_buffer_setup_hdr *)buf; ++ desccount = (uint32_t) pConcatValHdr->bDescCount; ++ pVals = (uint16_t *) (buf + BS_CONCAT_VAL_HDR_LEN); ++ ++ /* Check the DMA descriptor count */ ++ if (desccount > MAX_DMA_DESCS_PER_EP) { ++ CFI_INFO("%s: Maximum DMA Descriptor count should be %d\n", ++ __func__, MAX_DMA_DESCS_PER_EP); ++ return -DWC_E_INVALID; ++ } ++ ++ addr = pConcatValHdr->bEndpointAddress; ++ ep = get_cfi_ep_by_addr(pcd->cfi, addr); ++ if (NULL == ep) { ++ CFI_INFO("%s: Unable to get the endpoint addr=0x%02x\n", ++ __func__, addr); ++ return -DWC_E_INVALID; ++ } ++ ++ mps = UGETW(ep->ep->desc->wMaxPacketSize); ++ ++#if 0 ++ for (i = 0; i < desccount; i++) { ++ CFI_INFO("%s: wTxSize[%d]=0x%04x\n", __func__, i, pVals[i]); ++ } ++ CFI_INFO("%s: epname=%s; mps=%d\n", __func__, ep->ep->ep.name, mps); ++#endif ++ ++ /* Check the wTxSizes to be less than or equal to the mps */ ++ for (i = 0; i < desccount; i++) { ++ if (pVals[i] > mps) { ++ CFI_INFO ++ ("%s: ERROR - the wTxSize[%d] should be <= MPS (wTxSize=%d)\n", ++ __func__, i, pVals[i]); ++ return -DWC_E_INVALID; ++ } ++ } ++ ++ ep->ep->dwc_ep.buff_mode = BM_CONCAT; ++ dwc_memcpy(ep->bm_concat, pConcatValHdr, BS_CONCAT_VAL_HDR_LEN); ++ ++ /* Free the previously allocated storage for the wTxBytes */ ++ if (ep->bm_concat->wTxBytes) { ++ DWC_FREE(ep->bm_concat->wTxBytes); ++ } ++ ++ /* Allocate a new storage for the wTxBytes field */ ++ ep->bm_concat->wTxBytes = ++ DWC_ALLOC(sizeof(uint16_t) * pConcatValHdr->bDescCount); ++ if (NULL == ep->bm_concat->wTxBytes) { ++ CFI_INFO("%s: Unable to allocate memory\n", __func__); ++ return -DWC_E_NO_MEMORY; ++ } ++ ++ /* Copy the new values into the wTxBytes filed */ ++ dwc_memcpy(ep->bm_concat->wTxBytes, buf + BS_CONCAT_VAL_HDR_LEN, ++ sizeof(uint16_t) * pConcatValHdr->bDescCount); ++ ++ return 0; ++} ++ ++/** ++ * This function calculates the total of all FIFO sizes ++ * ++ * @param core_if Programming view of DWC_otg controller ++ * ++ * @return The total of data FIFO sizes. ++ * ++ */ ++static uint16_t get_dfifo_size(dwc_otg_core_if_t * core_if) ++{ ++ dwc_otg_core_params_t *params = core_if->core_params; ++ uint16_t dfifo_total = 0; ++ int i; ++ ++ /* The shared RxFIFO size */ ++ dfifo_total = ++ params->dev_rx_fifo_size + params->dev_nperio_tx_fifo_size; ++ ++ /* Add up each TxFIFO size to the total */ ++ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) { ++ dfifo_total += params->dev_tx_fifo_size[i]; ++ } ++ ++ return dfifo_total; ++} ++ ++/** ++ * This function returns Rx FIFO size ++ * ++ * @param core_if Programming view of DWC_otg controller ++ * ++ * @return The total of data FIFO sizes. ++ * ++ */ ++static int32_t get_rxfifo_size(dwc_otg_core_if_t * core_if, uint16_t wValue) ++{ ++ switch (wValue >> 8) { ++ case 0: ++ return (core_if->pwron_rxfsiz < ++ 32768) ? core_if->pwron_rxfsiz : 32768; ++ break; ++ case 1: ++ return core_if->core_params->dev_rx_fifo_size; ++ break; ++ default: ++ return -DWC_E_INVALID; ++ break; ++ } ++} ++ ++/** ++ * This function returns Tx FIFO size for IN EP ++ * ++ * @param core_if Programming view of DWC_otg controller ++ * ++ * @return The total of data FIFO sizes. ++ * ++ */ ++static int32_t get_txfifo_size(struct dwc_otg_pcd *pcd, uint16_t wValue) ++{ ++ dwc_otg_pcd_ep_t *ep; ++ ++ ep = get_ep_by_addr(pcd, wValue & 0xff); ++ ++ if (NULL == ep) { ++ CFI_INFO("%s: Unable to get the endpoint addr=0x%02x\n", ++ __func__, wValue & 0xff); ++ return -DWC_E_INVALID; ++ } ++ ++ if (!ep->dwc_ep.is_in) { ++ CFI_INFO ++ ("%s: No Tx FIFO assingned to the Out endpoint addr=0x%02x\n", ++ __func__, wValue & 0xff); ++ return -DWC_E_INVALID; ++ } ++ ++ switch (wValue >> 8) { ++ case 0: ++ return (GET_CORE_IF(pcd)->pwron_txfsiz ++ [ep->dwc_ep.tx_fifo_num - 1] < ++ 768) ? GET_CORE_IF(pcd)->pwron_txfsiz[ep-> ++ dwc_ep.tx_fifo_num ++ - 1] : 32768; ++ break; ++ case 1: ++ return GET_CORE_IF(pcd)->core_params-> ++ dev_tx_fifo_size[ep->dwc_ep.num - 1]; ++ break; ++ default: ++ return -DWC_E_INVALID; ++ break; ++ } ++} ++ ++/** ++ * This function checks if the submitted combination of ++ * device mode FIFO sizes is possible or not. ++ * ++ * @param core_if Programming view of DWC_otg controller ++ * ++ * @return 1 if possible, 0 otherwise. ++ * ++ */ ++static uint8_t check_fifo_sizes(dwc_otg_core_if_t * core_if) ++{ ++ uint16_t dfifo_actual = 0; ++ dwc_otg_core_params_t *params = core_if->core_params; ++ uint16_t start_addr = 0; ++ int i; ++ ++ dfifo_actual = ++ params->dev_rx_fifo_size + params->dev_nperio_tx_fifo_size; ++ ++ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) { ++ dfifo_actual += params->dev_tx_fifo_size[i]; ++ } ++ ++ if (dfifo_actual > core_if->total_fifo_size) { ++ return 0; ++ } ++ ++ if (params->dev_rx_fifo_size > 32768 || params->dev_rx_fifo_size < 16) ++ return 0; ++ ++ if (params->dev_nperio_tx_fifo_size > 32768 ++ || params->dev_nperio_tx_fifo_size < 16) ++ return 0; ++ ++ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) { ++ ++ if (params->dev_tx_fifo_size[i] > 768 ++ || params->dev_tx_fifo_size[i] < 4) ++ return 0; ++ } ++ ++ if (params->dev_rx_fifo_size > core_if->pwron_rxfsiz) ++ return 0; ++ start_addr = params->dev_rx_fifo_size; ++ ++ if (params->dev_nperio_tx_fifo_size > core_if->pwron_gnptxfsiz) ++ return 0; ++ start_addr += params->dev_nperio_tx_fifo_size; ++ ++ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) { ++ ++ if (params->dev_tx_fifo_size[i] > core_if->pwron_txfsiz[i]) ++ return 0; ++ start_addr += params->dev_tx_fifo_size[i]; ++ } ++ ++ return 1; ++} ++ ++/** ++ * This function resizes Device mode FIFOs ++ * ++ * @param core_if Programming view of DWC_otg controller ++ * ++ * @return 1 if successful, 0 otherwise ++ * ++ */ ++static uint8_t resize_fifos(dwc_otg_core_if_t * core_if) ++{ ++ int i = 0; ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ dwc_otg_core_params_t *params = core_if->core_params; ++ uint32_t rx_fifo_size; ++ fifosize_data_t nptxfifosize; ++ fifosize_data_t txfifosize[15]; ++ ++ uint32_t rx_fsz_bak; ++ uint32_t nptxfsz_bak; ++ uint32_t txfsz_bak[15]; ++ ++ uint16_t start_address; ++ uint8_t retval = 1; ++ ++ if (!check_fifo_sizes(core_if)) { ++ return 0; ++ } ++ ++ /* Configure data FIFO sizes */ ++ if (core_if->hwcfg2.b.dynamic_fifo && params->enable_dynamic_fifo) { ++ rx_fsz_bak = DWC_READ_REG32(&global_regs->grxfsiz); ++ rx_fifo_size = params->dev_rx_fifo_size; ++ DWC_WRITE_REG32(&global_regs->grxfsiz, rx_fifo_size); ++ ++ /* ++ * Tx FIFOs These FIFOs are numbered from 1 to 15. ++ * Indexes of the FIFO size module parameters in the ++ * dev_tx_fifo_size array and the FIFO size registers in ++ * the dtxfsiz array run from 0 to 14. ++ */ ++ ++ /* Non-periodic Tx FIFO */ ++ nptxfsz_bak = DWC_READ_REG32(&global_regs->gnptxfsiz); ++ nptxfifosize.b.depth = params->dev_nperio_tx_fifo_size; ++ start_address = params->dev_rx_fifo_size; ++ nptxfifosize.b.startaddr = start_address; ++ ++ DWC_WRITE_REG32(&global_regs->gnptxfsiz, nptxfifosize.d32); ++ ++ start_address += nptxfifosize.b.depth; ++ ++ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) { ++ txfsz_bak[i] = DWC_READ_REG32(&global_regs->dtxfsiz[i]); ++ ++ txfifosize[i].b.depth = params->dev_tx_fifo_size[i]; ++ txfifosize[i].b.startaddr = start_address; ++ DWC_WRITE_REG32(&global_regs->dtxfsiz[i], ++ txfifosize[i].d32); ++ ++ start_address += txfifosize[i].b.depth; ++ } ++ ++ /** Check if register values are set correctly */ ++ if (rx_fifo_size != DWC_READ_REG32(&global_regs->grxfsiz)) { ++ retval = 0; ++ } ++ ++ if (nptxfifosize.d32 != DWC_READ_REG32(&global_regs->gnptxfsiz)) { ++ retval = 0; ++ } ++ ++ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) { ++ if (txfifosize[i].d32 != ++ DWC_READ_REG32(&global_regs->dtxfsiz[i])) { ++ retval = 0; ++ } ++ } ++ ++ /** If register values are not set correctly, reset old values */ ++ if (retval == 0) { ++ DWC_WRITE_REG32(&global_regs->grxfsiz, rx_fsz_bak); ++ ++ /* Non-periodic Tx FIFO */ ++ DWC_WRITE_REG32(&global_regs->gnptxfsiz, nptxfsz_bak); ++ ++ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) { ++ DWC_WRITE_REG32(&global_regs->dtxfsiz[i], ++ txfsz_bak[i]); ++ } ++ } ++ } else { ++ return 0; ++ } ++ ++ /* Flush the FIFOs */ ++ dwc_otg_flush_tx_fifo(core_if, 0x10); /* all Tx FIFOs */ ++ dwc_otg_flush_rx_fifo(core_if); ++ ++ return retval; ++} ++ ++/** ++ * This function sets a new value for the buffer Alignment setup. ++ */ ++static int cfi_ep_set_tx_fifo_val(uint8_t * buf, dwc_otg_pcd_t * pcd) ++{ ++ int retval; ++ uint32_t fsiz; ++ uint16_t size; ++ uint16_t ep_addr; ++ dwc_otg_pcd_ep_t *ep; ++ dwc_otg_core_params_t *params = GET_CORE_IF(pcd)->core_params; ++ tx_fifo_size_setup_t *ptxfifoval; ++ ++ ptxfifoval = (tx_fifo_size_setup_t *) buf; ++ ep_addr = ptxfifoval->bEndpointAddress; ++ size = ptxfifoval->wDepth; ++ ++ ep = get_ep_by_addr(pcd, ep_addr); ++ ++ CFI_INFO ++ ("%s: Set Tx FIFO size: endpoint addr=0x%02x, depth=%d, FIFO Num=%d\n", ++ __func__, ep_addr, size, ep->dwc_ep.tx_fifo_num); ++ ++ if (NULL == ep) { ++ CFI_INFO("%s: Unable to get the endpoint addr=0x%02x\n", ++ __func__, ep_addr); ++ return -DWC_E_INVALID; ++ } ++ ++ fsiz = params->dev_tx_fifo_size[ep->dwc_ep.tx_fifo_num - 1]; ++ params->dev_tx_fifo_size[ep->dwc_ep.tx_fifo_num - 1] = size; ++ ++ if (resize_fifos(GET_CORE_IF(pcd))) { ++ retval = 0; ++ } else { ++ CFI_INFO ++ ("%s: Error setting the feature Tx FIFO Size for EP%d\n", ++ __func__, ep_addr); ++ params->dev_tx_fifo_size[ep->dwc_ep.tx_fifo_num - 1] = fsiz; ++ retval = -DWC_E_INVALID; ++ } ++ ++ return retval; ++} ++ ++/** ++ * This function sets a new value for the buffer Alignment setup. ++ */ ++static int cfi_set_rx_fifo_val(uint8_t * buf, dwc_otg_pcd_t * pcd) ++{ ++ int retval; ++ uint32_t fsiz; ++ uint16_t size; ++ dwc_otg_core_params_t *params = GET_CORE_IF(pcd)->core_params; ++ rx_fifo_size_setup_t *prxfifoval; ++ ++ prxfifoval = (rx_fifo_size_setup_t *) buf; ++ size = prxfifoval->wDepth; ++ ++ fsiz = params->dev_rx_fifo_size; ++ params->dev_rx_fifo_size = size; ++ ++ if (resize_fifos(GET_CORE_IF(pcd))) { ++ retval = 0; ++ } else { ++ CFI_INFO("%s: Error setting the feature Rx FIFO Size\n", ++ __func__); ++ params->dev_rx_fifo_size = fsiz; ++ retval = -DWC_E_INVALID; ++ } ++ ++ return retval; ++} ++ ++/** ++ * This function reads the SG of an EP's buffer setup into the buffer buf ++ */ ++static int cfi_ep_get_sg_val(uint8_t * buf, struct dwc_otg_pcd *pcd, ++ struct cfi_usb_ctrlrequest *req) ++{ ++ int retval = -DWC_E_INVALID; ++ uint8_t addr; ++ cfi_ep_t *ep; ++ ++ /* The Low Byte of the wValue contains a non-zero address of the endpoint */ ++ addr = req->wValue & 0xFF; ++ if (addr == 0) /* The address should be non-zero */ ++ return retval; ++ ++ ep = get_cfi_ep_by_addr(pcd->cfi, addr); ++ if (NULL == ep) { ++ CFI_INFO("%s: Unable to get the endpoint address(0x%02x)\n", ++ __func__, addr); ++ return retval; ++ } ++ ++ dwc_memcpy(buf, ep->bm_sg, BS_SG_VAL_DESC_LEN); ++ retval = BS_SG_VAL_DESC_LEN; ++ return retval; ++} ++ ++/** ++ * This function reads the Concatenation value of an EP's buffer mode into ++ * the buffer buf ++ */ ++static int cfi_ep_get_concat_val(uint8_t * buf, struct dwc_otg_pcd *pcd, ++ struct cfi_usb_ctrlrequest *req) ++{ ++ int retval = -DWC_E_INVALID; ++ uint8_t addr; ++ cfi_ep_t *ep; ++ uint8_t desc_count; ++ ++ /* The Low Byte of the wValue contains a non-zero address of the endpoint */ ++ addr = req->wValue & 0xFF; ++ if (addr == 0) /* The address should be non-zero */ ++ return retval; ++ ++ ep = get_cfi_ep_by_addr(pcd->cfi, addr); ++ if (NULL == ep) { ++ CFI_INFO("%s: Unable to get the endpoint address(0x%02x)\n", ++ __func__, addr); ++ return retval; ++ } ++ ++ /* Copy the header to the buffer */ ++ dwc_memcpy(buf, ep->bm_concat, BS_CONCAT_VAL_HDR_LEN); ++ /* Advance the buffer pointer by the header size */ ++ buf += BS_CONCAT_VAL_HDR_LEN; ++ ++ desc_count = ep->bm_concat->hdr.bDescCount; ++ /* Copy alll the wTxBytes to the buffer */ ++ dwc_memcpy(buf, ep->bm_concat->wTxBytes, sizeof(uid16_t) * desc_count); ++ ++ retval = BS_CONCAT_VAL_HDR_LEN + sizeof(uid16_t) * desc_count; ++ return retval; ++} ++ ++/** ++ * This function reads the buffer Alignment value of an EP's buffer mode into ++ * the buffer buf ++ * ++ * @return The total number of bytes copied to the buffer or negative error code. ++ */ ++static int cfi_ep_get_align_val(uint8_t * buf, struct dwc_otg_pcd *pcd, ++ struct cfi_usb_ctrlrequest *req) ++{ ++ int retval = -DWC_E_INVALID; ++ uint8_t addr; ++ cfi_ep_t *ep; ++ ++ /* The Low Byte of the wValue contains a non-zero address of the endpoint */ ++ addr = req->wValue & 0xFF; ++ if (addr == 0) /* The address should be non-zero */ ++ return retval; ++ ++ ep = get_cfi_ep_by_addr(pcd->cfi, addr); ++ if (NULL == ep) { ++ CFI_INFO("%s: Unable to get the endpoint address(0x%02x)\n", ++ __func__, addr); ++ return retval; ++ } ++ ++ dwc_memcpy(buf, ep->bm_align, BS_ALIGN_VAL_HDR_LEN); ++ retval = BS_ALIGN_VAL_HDR_LEN; ++ ++ return retval; ++} ++ ++/** ++ * This function sets a new value for the specified feature ++ * ++ * @param pcd A pointer to the PCD object ++ * ++ * @return 0 if successful, negative error code otherwise to stall the DCE. ++ */ ++static int cfi_set_feature_value(struct dwc_otg_pcd *pcd) ++{ ++ int retval = -DWC_E_NOT_SUPPORTED; ++ uint16_t wIndex, wValue; ++ uint8_t bRequest; ++ struct dwc_otg_core_if *coreif; ++ cfiobject_t *cfi = pcd->cfi; ++ struct cfi_usb_ctrlrequest *ctrl_req; ++ uint8_t *buf; ++ ctrl_req = &cfi->ctrl_req; ++ ++ buf = pcd->cfi->ctrl_req.data; ++ ++ coreif = GET_CORE_IF(pcd); ++ bRequest = ctrl_req->bRequest; ++ wIndex = DWC_CONSTANT_CPU_TO_LE16(ctrl_req->wIndex); ++ wValue = DWC_CONSTANT_CPU_TO_LE16(ctrl_req->wValue); ++ ++ /* See which feature is to be modified */ ++ switch (wIndex) { ++ case FT_ID_DMA_BUFFER_SETUP: ++ /* Modify the feature */ ++ if ((retval = cfi_ep_set_sg_val(buf, pcd)) < 0) ++ return retval; ++ ++ /* And send this request to the gadget */ ++ cfi->need_gadget_att = 1; ++ break; ++ ++ case FT_ID_DMA_BUFF_ALIGN: ++ if ((retval = cfi_ep_set_alignment_val(buf, pcd)) < 0) ++ return retval; ++ cfi->need_gadget_att = 1; ++ break; ++ ++ case FT_ID_DMA_CONCAT_SETUP: ++ /* Modify the feature */ ++ if ((retval = cfi_ep_set_concat_val(buf, pcd)) < 0) ++ return retval; ++ cfi->need_gadget_att = 1; ++ break; ++ ++ case FT_ID_DMA_CIRCULAR: ++ CFI_INFO("FT_ID_DMA_CIRCULAR\n"); ++ break; ++ ++ case FT_ID_THRESHOLD_SETUP: ++ CFI_INFO("FT_ID_THRESHOLD_SETUP\n"); ++ break; ++ ++ case FT_ID_DFIFO_DEPTH: ++ CFI_INFO("FT_ID_DFIFO_DEPTH\n"); ++ break; ++ ++ case FT_ID_TX_FIFO_DEPTH: ++ CFI_INFO("FT_ID_TX_FIFO_DEPTH\n"); ++ if ((retval = cfi_ep_set_tx_fifo_val(buf, pcd)) < 0) ++ return retval; ++ cfi->need_gadget_att = 0; ++ break; ++ ++ case FT_ID_RX_FIFO_DEPTH: ++ CFI_INFO("FT_ID_RX_FIFO_DEPTH\n"); ++ if ((retval = cfi_set_rx_fifo_val(buf, pcd)) < 0) ++ return retval; ++ cfi->need_gadget_att = 0; ++ break; ++ } ++ ++ return retval; ++} ++ ++#endif //DWC_UTE_CFI +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_cfi.h +@@ -0,0 +1,320 @@ ++/* ========================================================================== ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++#if !defined(__DWC_OTG_CFI_H__) ++#define __DWC_OTG_CFI_H__ ++ ++#include "dwc_otg_pcd.h" ++#include "dwc_cfi_common.h" ++ ++/** ++ * @file ++ * This file contains the CFI related OTG PCD specific common constants, ++ * interfaces(functions and macros) and data structures.The CFI Protocol is an ++ * optional interface for internal testing purposes that a DUT may implement to ++ * support testing of configurable features. ++ * ++ */ ++ ++struct dwc_otg_pcd; ++struct dwc_otg_pcd_ep; ++ ++/** OTG CFI Features (properties) ID constants */ ++/** This is a request for all Core Features */ ++#define FT_ID_DMA_MODE 0x0001 ++#define FT_ID_DMA_BUFFER_SETUP 0x0002 ++#define FT_ID_DMA_BUFF_ALIGN 0x0003 ++#define FT_ID_DMA_CONCAT_SETUP 0x0004 ++#define FT_ID_DMA_CIRCULAR 0x0005 ++#define FT_ID_THRESHOLD_SETUP 0x0006 ++#define FT_ID_DFIFO_DEPTH 0x0007 ++#define FT_ID_TX_FIFO_DEPTH 0x0008 ++#define FT_ID_RX_FIFO_DEPTH 0x0009 ++ ++/**********************************************************/ ++#define CFI_INFO_DEF ++ ++#ifdef CFI_INFO_DEF ++#define CFI_INFO(fmt...) DWC_PRINTF("CFI: " fmt); ++#else ++#define CFI_INFO(fmt...) ++#endif ++ ++#define min(x,y) ({ \ ++ x < y ? x : y; }) ++ ++#define max(x,y) ({ \ ++ x > y ? x : y; }) ++ ++/** ++ * Descriptor DMA SG Buffer setup structure (SG buffer). This structure is ++ * also used for setting up a buffer for Circular DDMA. ++ */ ++struct _ddma_sg_buffer_setup { ++#define BS_SG_VAL_DESC_LEN 6 ++ /* The OUT EP address */ ++ uint8_t bOutEndpointAddress; ++ /* The IN EP address */ ++ uint8_t bInEndpointAddress; ++ /* Number of bytes to put between transfer segments (must be DWORD boundaries) */ ++ uint8_t bOffset; ++ /* The number of transfer segments (a DMA descriptors per each segment) */ ++ uint8_t bCount; ++ /* Size (in byte) of each transfer segment */ ++ uint16_t wSize; ++} __attribute__ ((packed)); ++typedef struct _ddma_sg_buffer_setup ddma_sg_buffer_setup_t; ++ ++/** Descriptor DMA Concatenation Buffer setup structure */ ++struct _ddma_concat_buffer_setup_hdr { ++#define BS_CONCAT_VAL_HDR_LEN 4 ++ /* The endpoint for which the buffer is to be set up */ ++ uint8_t bEndpointAddress; ++ /* The count of descriptors to be used */ ++ uint8_t bDescCount; ++ /* The total size of the transfer */ ++ uint16_t wSize; ++} __attribute__ ((packed)); ++typedef struct _ddma_concat_buffer_setup_hdr ddma_concat_buffer_setup_hdr_t; ++ ++/** Descriptor DMA Concatenation Buffer setup structure */ ++struct _ddma_concat_buffer_setup { ++ /* The SG header */ ++ ddma_concat_buffer_setup_hdr_t hdr; ++ ++ /* The XFER sizes pointer (allocated dynamically) */ ++ uint16_t *wTxBytes; ++} __attribute__ ((packed)); ++typedef struct _ddma_concat_buffer_setup ddma_concat_buffer_setup_t; ++ ++/** Descriptor DMA Alignment Buffer setup structure */ ++struct _ddma_align_buffer_setup { ++#define BS_ALIGN_VAL_HDR_LEN 2 ++ uint8_t bEndpointAddress; ++ uint8_t bAlign; ++} __attribute__ ((packed)); ++typedef struct _ddma_align_buffer_setup ddma_align_buffer_setup_t; ++ ++/** Transmit FIFO Size setup structure */ ++struct _tx_fifo_size_setup { ++ uint8_t bEndpointAddress; ++ uint16_t wDepth; ++} __attribute__ ((packed)); ++typedef struct _tx_fifo_size_setup tx_fifo_size_setup_t; ++ ++/** Transmit FIFO Size setup structure */ ++struct _rx_fifo_size_setup { ++ uint16_t wDepth; ++} __attribute__ ((packed)); ++typedef struct _rx_fifo_size_setup rx_fifo_size_setup_t; ++ ++/** ++ * struct cfi_usb_ctrlrequest - the CFI implementation of the struct usb_ctrlrequest ++ * This structure encapsulates the standard usb_ctrlrequest and adds a pointer ++ * to the data returned in the data stage of a 3-stage Control Write requests. ++ */ ++struct cfi_usb_ctrlrequest { ++ uint8_t bRequestType; ++ uint8_t bRequest; ++ uint16_t wValue; ++ uint16_t wIndex; ++ uint16_t wLength; ++ uint8_t *data; ++} UPACKED; ++ ++/*---------------------------------------------------------------------------*/ ++ ++/** ++ * The CFI wrapper of the enabled and activated dwc_otg_pcd_ep structures. ++ * This structure is used to store the buffer setup data for any ++ * enabled endpoint in the PCD. ++ */ ++struct cfi_ep { ++ /* Entry for the list container */ ++ dwc_list_link_t lh; ++ /* Pointer to the active PCD endpoint structure */ ++ struct dwc_otg_pcd_ep *ep; ++ /* The last descriptor in the chain of DMA descriptors of the endpoint */ ++ struct dwc_otg_dma_desc *dma_desc_last; ++ /* The SG feature value */ ++ ddma_sg_buffer_setup_t *bm_sg; ++ /* The Circular feature value */ ++ ddma_sg_buffer_setup_t *bm_circ; ++ /* The Concatenation feature value */ ++ ddma_concat_buffer_setup_t *bm_concat; ++ /* The Alignment feature value */ ++ ddma_align_buffer_setup_t *bm_align; ++ /* XFER length */ ++ uint32_t xfer_len; ++ /* ++ * Count of DMA descriptors currently used. ++ * The total should not exceed the MAX_DMA_DESCS_PER_EP value ++ * defined in the dwc_otg_cil.h ++ */ ++ uint32_t desc_count; ++}; ++typedef struct cfi_ep cfi_ep_t; ++ ++typedef struct cfi_dma_buff { ++#define CFI_IN_BUF_LEN 1024 ++#define CFI_OUT_BUF_LEN 1024 ++ dma_addr_t addr; ++ uint8_t *buf; ++} cfi_dma_buff_t; ++ ++struct cfiobject; ++ ++/** ++ * This is the interface for the CFI operations. ++ * ++ * @param ep_enable Called when any endpoint is enabled and activated. ++ * @param release Called when the CFI object is released and it needs to correctly ++ * deallocate the dynamic memory ++ * @param ctrl_write_complete Called when the data stage of the request is complete ++ */ ++typedef struct cfi_ops { ++ int (*ep_enable) (struct cfiobject * cfi, struct dwc_otg_pcd * pcd, ++ struct dwc_otg_pcd_ep * ep); ++ void *(*ep_alloc_buf) (struct cfiobject * cfi, struct dwc_otg_pcd * pcd, ++ struct dwc_otg_pcd_ep * ep, dma_addr_t * dma, ++ unsigned size, gfp_t flags); ++ void (*release) (struct cfiobject * cfi); ++ int (*ctrl_write_complete) (struct cfiobject * cfi, ++ struct dwc_otg_pcd * pcd); ++ void (*build_descriptors) (struct cfiobject * cfi, ++ struct dwc_otg_pcd * pcd, ++ struct dwc_otg_pcd_ep * ep, ++ dwc_otg_pcd_request_t * req); ++} cfi_ops_t; ++ ++struct cfiobject { ++ cfi_ops_t ops; ++ struct dwc_otg_pcd *pcd; ++ struct usb_gadget *gadget; ++ ++ /* Buffers used to send/receive CFI-related request data */ ++ cfi_dma_buff_t buf_in; ++ cfi_dma_buff_t buf_out; ++ ++ /* CFI specific Control request wrapper */ ++ struct cfi_usb_ctrlrequest ctrl_req; ++ ++ /* The list of active EP's in the PCD of type cfi_ep_t */ ++ dwc_list_link_t active_eps; ++ ++ /* This flag shall control the propagation of a specific request ++ * to the gadget's processing routines. ++ * 0 - no gadget handling ++ * 1 - the gadget needs to know about this request (w/o completing a status ++ * phase - just return a 0 to the _setup callback) ++ */ ++ uint8_t need_gadget_att; ++ ++ /* Flag indicating whether the status IN phase needs to be ++ * completed by the PCD ++ */ ++ uint8_t need_status_in_complete; ++}; ++typedef struct cfiobject cfiobject_t; ++ ++#define DUMP_MSG ++ ++#if defined(DUMP_MSG) ++static inline void dump_msg(const u8 * buf, unsigned int length) ++{ ++ unsigned int start, num, i; ++ char line[52], *p; ++ ++ if (length >= 512) ++ return; ++ ++ start = 0; ++ while (length > 0) { ++ num = min(length, 16u); ++ p = line; ++ for (i = 0; i < num; ++i) { ++ if (i == 8) ++ *p++ = ' '; ++ DWC_SPRINTF(p, " %02x", buf[i]); ++ p += 3; ++ } ++ *p = 0; ++ DWC_DEBUG("%6x: %s\n", start, line); ++ buf += num; ++ start += num; ++ length -= num; ++ } ++} ++#else ++static inline void dump_msg(const u8 * buf, unsigned int length) ++{ ++} ++#endif ++ ++/** ++ * This function returns a pointer to cfi_ep_t object with the addr address. ++ */ ++static inline struct cfi_ep *get_cfi_ep_by_addr(struct cfiobject *cfi, ++ uint8_t addr) ++{ ++ struct cfi_ep *pcfiep; ++ dwc_list_link_t *tmp; ++ ++ DWC_LIST_FOREACH(tmp, &cfi->active_eps) { ++ pcfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh); ++ ++ if (pcfiep->ep->desc->bEndpointAddress == addr) { ++ return pcfiep; ++ } ++ } ++ ++ return NULL; ++} ++ ++/** ++ * This function returns a pointer to cfi_ep_t object that matches ++ * the dwc_otg_pcd_ep object. ++ */ ++static inline struct cfi_ep *get_cfi_ep_by_pcd_ep(struct cfiobject *cfi, ++ struct dwc_otg_pcd_ep *ep) ++{ ++ struct cfi_ep *pcfiep = NULL; ++ dwc_list_link_t *tmp; ++ ++ DWC_LIST_FOREACH(tmp, &cfi->active_eps) { ++ pcfiep = DWC_LIST_ENTRY(tmp, struct cfi_ep, lh); ++ if (pcfiep->ep == ep) { ++ return pcfiep; ++ } ++ } ++ return NULL; ++} ++ ++int cfi_setup(struct dwc_otg_pcd *pcd, struct cfi_usb_ctrlrequest *ctrl); ++ ++#endif /* (__DWC_OTG_CFI_H__) */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_cil.c +@@ -0,0 +1,7146 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_cil.c $ ++ * $Revision: #191 $ ++ * $Date: 2012/08/10 $ ++ * $Change: 2047372 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++/** @file ++ * ++ * The Core Interface Layer provides basic services for accessing and ++ * managing the DWC_otg hardware. These services are used by both the ++ * Host Controller Driver and the Peripheral Controller Driver. ++ * ++ * The CIL manages the memory map for the core so that the HCD and PCD ++ * don't have to do this separately. It also handles basic tasks like ++ * reading/writing the registers and data FIFOs in the controller. ++ * Some of the data access functions provide encapsulation of several ++ * operations required to perform a task, such as writing multiple ++ * registers to start a transfer. Finally, the CIL performs basic ++ * services that are not specific to either the host or device modes ++ * of operation. These services include management of the OTG Host ++ * Negotiation Protocol (HNP) and Session Request Protocol (SRP). A ++ * Diagnostic API is also provided to allow testing of the controller ++ * hardware. ++ * ++ * The Core Interface Layer has the following requirements: ++ * - Provides basic controller operations. ++ * - Minimal use of OS services. ++ * - The OS services used will be abstracted by using inline functions ++ * or macros. ++ * ++ */ ++ ++#include "dwc_os.h" ++#include "dwc_otg_regs.h" ++#include "dwc_otg_cil.h" ++ ++extern bool cil_force_host; ++ ++static int dwc_otg_setup_params(dwc_otg_core_if_t * core_if); ++ ++/** ++ * This function is called to initialize the DWC_otg CSR data ++ * structures. The register addresses in the device and host ++ * structures are initialized from the base address supplied by the ++ * caller. The calling function must make the OS calls to get the ++ * base address of the DWC_otg controller registers. The core_params ++ * argument holds the parameters that specify how the core should be ++ * configured. ++ * ++ * @param reg_base_addr Base address of DWC_otg core registers ++ * ++ */ ++dwc_otg_core_if_t *dwc_otg_cil_init(const uint32_t * reg_base_addr) ++{ ++ dwc_otg_core_if_t *core_if = 0; ++ dwc_otg_dev_if_t *dev_if = 0; ++ dwc_otg_host_if_t *host_if = 0; ++ uint8_t *reg_base = (uint8_t *) reg_base_addr; ++ int i = 0; ++ ++ DWC_DEBUGPL(DBG_CILV, "%s(%p)\n", __func__, reg_base_addr); ++ ++ core_if = DWC_ALLOC(sizeof(dwc_otg_core_if_t)); ++ ++ if (core_if == NULL) { ++ DWC_DEBUGPL(DBG_CIL, ++ "Allocation of dwc_otg_core_if_t failed\n"); ++ return 0; ++ } ++ core_if->core_global_regs = (dwc_otg_core_global_regs_t *) reg_base; ++ ++ /* ++ * Allocate the Device Mode structures. ++ */ ++ dev_if = DWC_ALLOC(sizeof(dwc_otg_dev_if_t)); ++ ++ if (dev_if == NULL) { ++ DWC_DEBUGPL(DBG_CIL, "Allocation of dwc_otg_dev_if_t failed\n"); ++ DWC_FREE(core_if); ++ return 0; ++ } ++ ++ dev_if->dev_global_regs = ++ (dwc_otg_device_global_regs_t *) (reg_base + ++ DWC_DEV_GLOBAL_REG_OFFSET); ++ ++ for (i = 0; i < MAX_EPS_CHANNELS; i++) { ++ dev_if->in_ep_regs[i] = (dwc_otg_dev_in_ep_regs_t *) ++ (reg_base + DWC_DEV_IN_EP_REG_OFFSET + ++ (i * DWC_EP_REG_OFFSET)); ++ ++ dev_if->out_ep_regs[i] = (dwc_otg_dev_out_ep_regs_t *) ++ (reg_base + DWC_DEV_OUT_EP_REG_OFFSET + ++ (i * DWC_EP_REG_OFFSET)); ++ DWC_DEBUGPL(DBG_CILV, "in_ep_regs[%d]->diepctl=%p\n", ++ i, &dev_if->in_ep_regs[i]->diepctl); ++ DWC_DEBUGPL(DBG_CILV, "out_ep_regs[%d]->doepctl=%p\n", ++ i, &dev_if->out_ep_regs[i]->doepctl); ++ } ++ ++ dev_if->speed = 0; // unknown ++ ++ core_if->dev_if = dev_if; ++ ++ /* ++ * Allocate the Host Mode structures. ++ */ ++ host_if = DWC_ALLOC(sizeof(dwc_otg_host_if_t)); ++ ++ if (host_if == NULL) { ++ DWC_DEBUGPL(DBG_CIL, ++ "Allocation of dwc_otg_host_if_t failed\n"); ++ DWC_FREE(dev_if); ++ DWC_FREE(core_if); ++ return 0; ++ } ++ ++ host_if->host_global_regs = (dwc_otg_host_global_regs_t *) ++ (reg_base + DWC_OTG_HOST_GLOBAL_REG_OFFSET); ++ ++ host_if->hprt0 = ++ (uint32_t *) (reg_base + DWC_OTG_HOST_PORT_REGS_OFFSET); ++ ++ for (i = 0; i < MAX_EPS_CHANNELS; i++) { ++ host_if->hc_regs[i] = (dwc_otg_hc_regs_t *) ++ (reg_base + DWC_OTG_HOST_CHAN_REGS_OFFSET + ++ (i * DWC_OTG_CHAN_REGS_OFFSET)); ++ DWC_DEBUGPL(DBG_CILV, "hc_reg[%d]->hcchar=%p\n", ++ i, &host_if->hc_regs[i]->hcchar); ++ } ++ ++ host_if->num_host_channels = MAX_EPS_CHANNELS; ++ core_if->host_if = host_if; ++ ++ for (i = 0; i < MAX_EPS_CHANNELS; i++) { ++ core_if->data_fifo[i] = ++ (uint32_t *) (reg_base + DWC_OTG_DATA_FIFO_OFFSET + ++ (i * DWC_OTG_DATA_FIFO_SIZE)); ++ DWC_DEBUGPL(DBG_CILV, "data_fifo[%d]=0x%08lx\n", ++ i, (unsigned long)core_if->data_fifo[i]); ++ } ++ ++ core_if->pcgcctl = (uint32_t *) (reg_base + DWC_OTG_PCGCCTL_OFFSET); ++ ++ /* Initiate lx_state to L3 disconnected state */ ++ core_if->lx_state = DWC_OTG_L3; ++ /* ++ * Store the contents of the hardware configuration registers here for ++ * easy access later. ++ */ ++ core_if->hwcfg1.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->ghwcfg1); ++ core_if->hwcfg2.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->ghwcfg2); ++ core_if->hwcfg3.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->ghwcfg3); ++ core_if->hwcfg4.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->ghwcfg4); ++ ++ /* Force host mode to get HPTXFSIZ exact power on value */ ++ { ++ gusbcfg_data_t gusbcfg = {.d32 = 0 }; ++ gusbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg); ++ gusbcfg.b.force_host_mode = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, gusbcfg.d32); ++ dwc_mdelay(100); ++ core_if->hptxfsiz.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->hptxfsiz); ++ gusbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg); ++ if (cil_force_host) ++ gusbcfg.b.force_host_mode = 1; ++ else ++ gusbcfg.b.force_host_mode = 0; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, gusbcfg.d32); ++ dwc_mdelay(100); ++ } ++ ++ DWC_DEBUGPL(DBG_CILV, "hwcfg1=%08x\n", core_if->hwcfg1.d32); ++ DWC_DEBUGPL(DBG_CILV, "hwcfg2=%08x\n", core_if->hwcfg2.d32); ++ DWC_DEBUGPL(DBG_CILV, "hwcfg3=%08x\n", core_if->hwcfg3.d32); ++ DWC_DEBUGPL(DBG_CILV, "hwcfg4=%08x\n", core_if->hwcfg4.d32); ++ ++ core_if->hcfg.d32 = ++ DWC_READ_REG32(&core_if->host_if->host_global_regs->hcfg); ++ core_if->dcfg.d32 = ++ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg); ++ ++ DWC_DEBUGPL(DBG_CILV, "hcfg=%08x\n", core_if->hcfg.d32); ++ DWC_DEBUGPL(DBG_CILV, "dcfg=%08x\n", core_if->dcfg.d32); ++ ++ DWC_DEBUGPL(DBG_CILV, "op_mode=%0x\n", core_if->hwcfg2.b.op_mode); ++ DWC_DEBUGPL(DBG_CILV, "arch=%0x\n", core_if->hwcfg2.b.architecture); ++ DWC_DEBUGPL(DBG_CILV, "num_dev_ep=%d\n", core_if->hwcfg2.b.num_dev_ep); ++ DWC_DEBUGPL(DBG_CILV, "num_host_chan=%d\n", ++ core_if->hwcfg2.b.num_host_chan); ++ DWC_DEBUGPL(DBG_CILV, "nonperio_tx_q_depth=0x%0x\n", ++ core_if->hwcfg2.b.nonperio_tx_q_depth); ++ DWC_DEBUGPL(DBG_CILV, "host_perio_tx_q_depth=0x%0x\n", ++ core_if->hwcfg2.b.host_perio_tx_q_depth); ++ DWC_DEBUGPL(DBG_CILV, "dev_token_q_depth=0x%0x\n", ++ core_if->hwcfg2.b.dev_token_q_depth); ++ ++ DWC_DEBUGPL(DBG_CILV, "Total FIFO SZ=%d\n", ++ core_if->hwcfg3.b.dfifo_depth); ++ DWC_DEBUGPL(DBG_CILV, "xfer_size_cntr_width=%0x\n", ++ core_if->hwcfg3.b.xfer_size_cntr_width); ++ ++ /* ++ * Set the SRP sucess bit for FS-I2c ++ */ ++ core_if->srp_success = 0; ++ core_if->srp_timer_started = 0; ++ ++ /* ++ * Create new workqueue and init works ++ */ ++ core_if->wq_otg = DWC_WORKQ_ALLOC("dwc_otg"); ++ if (core_if->wq_otg == 0) { ++ DWC_WARN("DWC_WORKQ_ALLOC failed\n"); ++ DWC_FREE(host_if); ++ DWC_FREE(dev_if); ++ DWC_FREE(core_if); ++ return 0; ++ } ++ ++ core_if->snpsid = DWC_READ_REG32(&core_if->core_global_regs->gsnpsid); ++ ++ DWC_PRINTF("Core Release: %x.%x%x%x\n", ++ (core_if->snpsid >> 12 & 0xF), ++ (core_if->snpsid >> 8 & 0xF), ++ (core_if->snpsid >> 4 & 0xF), (core_if->snpsid & 0xF)); ++ ++ core_if->wkp_timer = DWC_TIMER_ALLOC("Wake Up Timer", ++ w_wakeup_detected, core_if); ++ if (core_if->wkp_timer == 0) { ++ DWC_WARN("DWC_TIMER_ALLOC failed\n"); ++ DWC_FREE(host_if); ++ DWC_FREE(dev_if); ++ DWC_WORKQ_FREE(core_if->wq_otg); ++ DWC_FREE(core_if); ++ return 0; ++ } ++ ++ if (dwc_otg_setup_params(core_if)) { ++ DWC_WARN("Error while setting core params\n"); ++ } ++ ++ core_if->hibernation_suspend = 0; ++ ++ /** ADP initialization */ ++ dwc_otg_adp_init(core_if); ++ ++ return core_if; ++} ++ ++/** ++ * This function frees the structures allocated by dwc_otg_cil_init(). ++ * ++ * @param core_if The core interface pointer returned from ++ * dwc_otg_cil_init(). ++ * ++ */ ++void dwc_otg_cil_remove(dwc_otg_core_if_t * core_if) ++{ ++ dctl_data_t dctl = {.d32 = 0 }; ++ DWC_DEBUGPL(DBG_CILV, "%s(%p)\n", __func__, core_if); ++ ++ /* Disable all interrupts */ ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gahbcfg, 1, 0); ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, 0); ++ ++ dctl.b.sftdiscon = 1; ++ if (core_if->snpsid >= OTG_CORE_REV_3_00a) { ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0, ++ dctl.d32); ++ } ++ ++ if (core_if->wq_otg) { ++ DWC_WORKQ_WAIT_WORK_DONE(core_if->wq_otg, 500); ++ DWC_WORKQ_FREE(core_if->wq_otg); ++ } ++ if (core_if->dev_if) { ++ DWC_FREE(core_if->dev_if); ++ } ++ if (core_if->host_if) { ++ DWC_FREE(core_if->host_if); ++ } ++ ++ /** Remove ADP Stuff */ ++ dwc_otg_adp_remove(core_if); ++ if (core_if->core_params) { ++ DWC_FREE(core_if->core_params); ++ } ++ if (core_if->wkp_timer) { ++ DWC_TIMER_FREE(core_if->wkp_timer); ++ } ++ if (core_if->srp_timer) { ++ DWC_TIMER_FREE(core_if->srp_timer); ++ } ++ DWC_FREE(core_if); ++} ++ ++/** ++ * This function enables the controller's Global Interrupt in the AHB Config ++ * register. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++void dwc_otg_enable_global_interrupts(dwc_otg_core_if_t * core_if) ++{ ++ gahbcfg_data_t ahbcfg = {.d32 = 0 }; ++ ahbcfg.b.glblintrmsk = 1; /* Enable interrupts */ ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gahbcfg, 0, ahbcfg.d32); ++} ++ ++/** ++ * This function disables the controller's Global Interrupt in the AHB Config ++ * register. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++void dwc_otg_disable_global_interrupts(dwc_otg_core_if_t * core_if) ++{ ++ gahbcfg_data_t ahbcfg = {.d32 = 0 }; ++ ahbcfg.b.glblintrmsk = 1; /* Disable interrupts */ ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gahbcfg, ahbcfg.d32, 0); ++} ++ ++/** ++ * This function initializes the commmon interrupts, used in both ++ * device and host modes. ++ * ++ * @param core_if Programming view of the DWC_otg controller ++ * ++ */ ++static void dwc_otg_enable_common_interrupts(dwc_otg_core_if_t * core_if) ++{ ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ /* Clear any pending OTG Interrupts */ ++ DWC_WRITE_REG32(&global_regs->gotgint, 0xFFFFFFFF); ++ ++ /* Clear any pending interrupts */ ++ DWC_WRITE_REG32(&global_regs->gintsts, 0xFFFFFFFF); ++ ++ /* ++ * Enable the interrupts in the GINTMSK. ++ */ ++ intr_mask.b.modemismatch = 1; ++ intr_mask.b.otgintr = 1; ++ ++ if (!core_if->dma_enable) { ++ intr_mask.b.rxstsqlvl = 1; ++ } ++ ++ intr_mask.b.conidstschng = 1; ++ intr_mask.b.wkupintr = 1; ++ intr_mask.b.disconnect = 0; ++ intr_mask.b.usbsuspend = 1; ++ intr_mask.b.sessreqintr = 1; ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ if (core_if->core_params->lpm_enable) { ++ intr_mask.b.lpmtranrcvd = 1; ++ } ++#endif ++ DWC_WRITE_REG32(&global_regs->gintmsk, intr_mask.d32); ++} ++ ++/* ++ * The restore operation is modified to support Synopsys Emulated Powerdown and ++ * Hibernation. This function is for exiting from Device mode hibernation by ++ * Host Initiated Resume/Reset and Device Initiated Remote-Wakeup. ++ * @param core_if Programming view of DWC_otg controller. ++ * @param rem_wakeup - indicates whether resume is initiated by Device or Host. ++ * @param reset - indicates whether resume is initiated by Reset. ++ */ ++int dwc_otg_device_hibernation_restore(dwc_otg_core_if_t * core_if, ++ int rem_wakeup, int reset) ++{ ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ dctl_data_t dctl = {.d32 = 0 }; ++ ++ int timeout = 2000; ++ ++ if (!core_if->hibernation_suspend) { ++ DWC_PRINTF("Already exited from Hibernation\n"); ++ return 1; ++ } ++ ++ DWC_DEBUGPL(DBG_PCD, "%s called\n", __FUNCTION__); ++ /* Switch-on voltage to the core */ ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Reset core */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Assert Restore signal */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.restore = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Disable power clamps */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnclmp = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ if (rem_wakeup) { ++ dwc_udelay(70); ++ } ++ ++ /* Deassert Reset core */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Disable PMU interrupt */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ /* Mask interrupts from gpwrdn */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.connect_det_msk = 1; ++ gpwrdn.b.srp_det_msk = 1; ++ gpwrdn.b.disconn_det_msk = 1; ++ gpwrdn.b.rst_det_msk = 1; ++ gpwrdn.b.lnstchng_msk = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ /* Indicates that we are going out from hibernation */ ++ core_if->hibernation_suspend = 0; ++ ++ /* ++ * Set Restore Essential Regs bit in PCGCCTL register, restore_mode = 1 ++ * indicates restore from remote_wakeup ++ */ ++ restore_essential_regs(core_if, rem_wakeup, 0); ++ ++ /* ++ * Wait a little for seeing new value of variable hibernation_suspend if ++ * Restore done interrupt received before polling ++ */ ++ dwc_udelay(10); ++ ++ if (core_if->hibernation_suspend == 0) { ++ /* ++ * Wait For Restore_done Interrupt. This mechanism of polling the ++ * interrupt is introduced to avoid any possible race conditions ++ */ ++ do { ++ gintsts_data_t gintsts; ++ gintsts.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->gintsts); ++ if (gintsts.b.restoredone) { ++ gintsts.d32 = 0; ++ gintsts.b.restoredone = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs-> ++ gintsts, gintsts.d32); ++ DWC_PRINTF("Restore Done Interrupt seen\n"); ++ break; ++ } ++ dwc_udelay(10); ++ } while (--timeout); ++ if (!timeout) { ++ DWC_PRINTF("Restore Done interrupt wasn't generated here\n"); ++ } ++ } ++ /* Clear all pending interupts */ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF); ++ ++ /* De-assert Restore */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.restore = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ if (!rem_wakeup) { ++ pcgcctl.d32 = 0; ++ pcgcctl.b.rstpdwnmodule = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0); ++ } ++ ++ /* Restore GUSBCFG and DCFG */ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, ++ core_if->gr_backup->gusbcfg_local); ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg, ++ core_if->dr_backup->dcfg); ++ ++ /* De-assert Wakeup Logic */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ if (!rem_wakeup) { ++ /* Set Device programming done bit */ ++ dctl.b.pwronprgdone = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0, dctl.d32); ++ } else { ++ /* Start Remote Wakeup Signaling */ ++ dctl.d32 = core_if->dr_backup->dctl; ++ dctl.b.rmtwkupsig = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32); ++ } ++ ++ dwc_mdelay(2); ++ /* Clear all pending interupts */ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF); ++ ++ /* Restore global registers */ ++ dwc_otg_restore_global_regs(core_if); ++ /* Restore device global registers */ ++ dwc_otg_restore_dev_regs(core_if, rem_wakeup); ++ ++ if (rem_wakeup) { ++ dwc_mdelay(7); ++ dctl.d32 = 0; ++ dctl.b.rmtwkupsig = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32, 0); ++ } ++ ++ core_if->hibernation_suspend = 0; ++ /* The core will be in ON STATE */ ++ core_if->lx_state = DWC_OTG_L0; ++ DWC_PRINTF("Hibernation recovery completes here\n"); ++ ++ return 1; ++} ++ ++/* ++ * The restore operation is modified to support Synopsys Emulated Powerdown and ++ * Hibernation. This function is for exiting from Host mode hibernation by ++ * Host Initiated Resume/Reset and Device Initiated Remote-Wakeup. ++ * @param core_if Programming view of DWC_otg controller. ++ * @param rem_wakeup - indicates whether resume is initiated by Device or Host. ++ * @param reset - indicates whether resume is initiated by Reset. ++ */ ++int dwc_otg_host_hibernation_restore(dwc_otg_core_if_t * core_if, ++ int rem_wakeup, int reset) ++{ ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ hprt0_data_t hprt0 = {.d32 = 0 }; ++ ++ int timeout = 2000; ++ ++ DWC_DEBUGPL(DBG_HCD, "%s called\n", __FUNCTION__); ++ /* Switch-on voltage to the core */ ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Reset core */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Assert Restore signal */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.restore = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Disable power clamps */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnclmp = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ if (!rem_wakeup) { ++ dwc_udelay(50); ++ } ++ ++ /* Deassert Reset core */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Disable PMU interrupt */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.connect_det_msk = 1; ++ gpwrdn.b.srp_det_msk = 1; ++ gpwrdn.b.disconn_det_msk = 1; ++ gpwrdn.b.rst_det_msk = 1; ++ gpwrdn.b.lnstchng_msk = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ /* Indicates that we are going out from hibernation */ ++ core_if->hibernation_suspend = 0; ++ ++ /* Set Restore Essential Regs bit in PCGCCTL register */ ++ restore_essential_regs(core_if, rem_wakeup, 1); ++ ++ /* Wait a little for seeing new value of variable hibernation_suspend if ++ * Restore done interrupt received before polling */ ++ dwc_udelay(10); ++ ++ if (core_if->hibernation_suspend == 0) { ++ /* Wait For Restore_done Interrupt. This mechanism of polling the ++ * interrupt is introduced to avoid any possible race conditions ++ */ ++ do { ++ gintsts_data_t gintsts; ++ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts); ++ if (gintsts.b.restoredone) { ++ gintsts.d32 = 0; ++ gintsts.b.restoredone = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ DWC_DEBUGPL(DBG_HCD,"Restore Done Interrupt seen\n"); ++ break; ++ } ++ dwc_udelay(10); ++ } while (--timeout); ++ if (!timeout) { ++ DWC_WARN("Restore Done interrupt wasn't generated\n"); ++ } ++ } ++ ++ /* Set the flag's value to 0 again after receiving restore done interrupt */ ++ core_if->hibernation_suspend = 0; ++ ++ /* This step is not described in functional spec but if not wait for this ++ * delay, mismatch interrupts occurred because just after restore core is ++ * in Device mode(gintsts.curmode == 0) */ ++ dwc_mdelay(100); ++ ++ /* Clear all pending interrupts */ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF); ++ ++ /* De-assert Restore */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.restore = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Restore GUSBCFG and HCFG */ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, ++ core_if->gr_backup->gusbcfg_local); ++ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hcfg, ++ core_if->hr_backup->hcfg_local); ++ ++ /* De-assert Wakeup Logic */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Start the Resume operation by programming HPRT0 */ ++ hprt0.d32 = core_if->hr_backup->hprt0_local; ++ hprt0.b.prtpwr = 1; ++ hprt0.b.prtena = 0; ++ hprt0.b.prtsusp = 0; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ ++ DWC_PRINTF("Resume Starts Now\n"); ++ if (!reset) { // Indicates it is Resume Operation ++ hprt0.d32 = core_if->hr_backup->hprt0_local; ++ hprt0.b.prtres = 1; ++ hprt0.b.prtpwr = 1; ++ hprt0.b.prtena = 0; ++ hprt0.b.prtsusp = 0; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ ++ if (!rem_wakeup) ++ hprt0.b.prtres = 0; ++ /* Wait for Resume time and then program HPRT again */ ++ dwc_mdelay(100); ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ ++ } else { // Indicates it is Reset Operation ++ hprt0.d32 = core_if->hr_backup->hprt0_local; ++ hprt0.b.prtrst = 1; ++ hprt0.b.prtpwr = 1; ++ hprt0.b.prtena = 0; ++ hprt0.b.prtsusp = 0; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ /* Wait for Reset time and then program HPRT again */ ++ dwc_mdelay(60); ++ hprt0.b.prtrst = 0; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ } ++ /* Clear all interrupt status */ ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtconndet = 1; ++ hprt0.b.prtenchng = 1; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ ++ /* Clear all pending interupts */ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF); ++ ++ /* Restore global registers */ ++ dwc_otg_restore_global_regs(core_if); ++ /* Restore host global registers */ ++ dwc_otg_restore_host_regs(core_if, reset); ++ ++ /* The core will be in ON STATE */ ++ core_if->lx_state = DWC_OTG_L0; ++ DWC_PRINTF("Hibernation recovery is complete here\n"); ++ return 0; ++} ++ ++/** Saves some register values into system memory. */ ++int dwc_otg_save_global_regs(dwc_otg_core_if_t * core_if) ++{ ++ struct dwc_otg_global_regs_backup *gr; ++ int i; ++ ++ gr = core_if->gr_backup; ++ if (!gr) { ++ gr = DWC_ALLOC(sizeof(*gr)); ++ if (!gr) { ++ return -DWC_E_NO_MEMORY; ++ } ++ core_if->gr_backup = gr; ++ } ++ ++ gr->gotgctl_local = DWC_READ_REG32(&core_if->core_global_regs->gotgctl); ++ gr->gintmsk_local = DWC_READ_REG32(&core_if->core_global_regs->gintmsk); ++ gr->gahbcfg_local = DWC_READ_REG32(&core_if->core_global_regs->gahbcfg); ++ gr->gusbcfg_local = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg); ++ gr->grxfsiz_local = DWC_READ_REG32(&core_if->core_global_regs->grxfsiz); ++ gr->gnptxfsiz_local = DWC_READ_REG32(&core_if->core_global_regs->gnptxfsiz); ++ gr->hptxfsiz_local = DWC_READ_REG32(&core_if->core_global_regs->hptxfsiz); ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ gr->glpmcfg_local = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++#endif ++ gr->gi2cctl_local = DWC_READ_REG32(&core_if->core_global_regs->gi2cctl); ++ gr->pcgcctl_local = DWC_READ_REG32(core_if->pcgcctl); ++ gr->gdfifocfg_local = ++ DWC_READ_REG32(&core_if->core_global_regs->gdfifocfg); ++ for (i = 0; i < MAX_EPS_CHANNELS; i++) { ++ gr->dtxfsiz_local[i] = ++ DWC_READ_REG32(&(core_if->core_global_regs->dtxfsiz[i])); ++ } ++ ++ DWC_DEBUGPL(DBG_ANY, "===========Backing Global registers==========\n"); ++ DWC_DEBUGPL(DBG_ANY, "Backed up gotgctl = %08x\n", gr->gotgctl_local); ++ DWC_DEBUGPL(DBG_ANY, "Backed up gintmsk = %08x\n", gr->gintmsk_local); ++ DWC_DEBUGPL(DBG_ANY, "Backed up gahbcfg = %08x\n", gr->gahbcfg_local); ++ DWC_DEBUGPL(DBG_ANY, "Backed up gusbcfg = %08x\n", gr->gusbcfg_local); ++ DWC_DEBUGPL(DBG_ANY, "Backed up grxfsiz = %08x\n", gr->grxfsiz_local); ++ DWC_DEBUGPL(DBG_ANY, "Backed up gnptxfsiz = %08x\n", ++ gr->gnptxfsiz_local); ++ DWC_DEBUGPL(DBG_ANY, "Backed up hptxfsiz = %08x\n", ++ gr->hptxfsiz_local); ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ DWC_DEBUGPL(DBG_ANY, "Backed up glpmcfg = %08x\n", gr->glpmcfg_local); ++#endif ++ DWC_DEBUGPL(DBG_ANY, "Backed up gi2cctl = %08x\n", gr->gi2cctl_local); ++ DWC_DEBUGPL(DBG_ANY, "Backed up pcgcctl = %08x\n", gr->pcgcctl_local); ++ DWC_DEBUGPL(DBG_ANY,"Backed up gdfifocfg = %08x\n",gr->gdfifocfg_local); ++ ++ return 0; ++} ++ ++/** Saves GINTMSK register before setting the msk bits. */ ++int dwc_otg_save_gintmsk_reg(dwc_otg_core_if_t * core_if) ++{ ++ struct dwc_otg_global_regs_backup *gr; ++ ++ gr = core_if->gr_backup; ++ if (!gr) { ++ gr = DWC_ALLOC(sizeof(*gr)); ++ if (!gr) { ++ return -DWC_E_NO_MEMORY; ++ } ++ core_if->gr_backup = gr; ++ } ++ ++ gr->gintmsk_local = DWC_READ_REG32(&core_if->core_global_regs->gintmsk); ++ ++ DWC_DEBUGPL(DBG_ANY,"=============Backing GINTMSK registers============\n"); ++ DWC_DEBUGPL(DBG_ANY, "Backed up gintmsk = %08x\n", gr->gintmsk_local); ++ ++ return 0; ++} ++ ++int dwc_otg_save_dev_regs(dwc_otg_core_if_t * core_if) ++{ ++ struct dwc_otg_dev_regs_backup *dr; ++ int i; ++ ++ dr = core_if->dr_backup; ++ if (!dr) { ++ dr = DWC_ALLOC(sizeof(*dr)); ++ if (!dr) { ++ return -DWC_E_NO_MEMORY; ++ } ++ core_if->dr_backup = dr; ++ } ++ ++ dr->dcfg = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg); ++ dr->dctl = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dctl); ++ dr->daintmsk = ++ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->daintmsk); ++ dr->diepmsk = ++ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->diepmsk); ++ dr->doepmsk = ++ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->doepmsk); ++ ++ for (i = 0; i < core_if->dev_if->num_in_eps; ++i) { ++ dr->diepctl[i] = ++ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[i]->diepctl); ++ dr->dieptsiz[i] = ++ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[i]->dieptsiz); ++ dr->diepdma[i] = ++ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[i]->diepdma); ++ } ++ ++ DWC_DEBUGPL(DBG_ANY, ++ "=============Backing Host registers==============\n"); ++ DWC_DEBUGPL(DBG_ANY, "Backed up dcfg = %08x\n", dr->dcfg); ++ DWC_DEBUGPL(DBG_ANY, "Backed up dctl = %08x\n", dr->dctl); ++ DWC_DEBUGPL(DBG_ANY, "Backed up daintmsk = %08x\n", ++ dr->daintmsk); ++ DWC_DEBUGPL(DBG_ANY, "Backed up diepmsk = %08x\n", dr->diepmsk); ++ DWC_DEBUGPL(DBG_ANY, "Backed up doepmsk = %08x\n", dr->doepmsk); ++ for (i = 0; i < core_if->dev_if->num_in_eps; ++i) { ++ DWC_DEBUGPL(DBG_ANY, "Backed up diepctl[%d] = %08x\n", i, ++ dr->diepctl[i]); ++ DWC_DEBUGPL(DBG_ANY, "Backed up dieptsiz[%d] = %08x\n", ++ i, dr->dieptsiz[i]); ++ DWC_DEBUGPL(DBG_ANY, "Backed up diepdma[%d] = %08x\n", i, ++ dr->diepdma[i]); ++ } ++ ++ return 0; ++} ++ ++int dwc_otg_save_host_regs(dwc_otg_core_if_t * core_if) ++{ ++ struct dwc_otg_host_regs_backup *hr; ++ int i; ++ ++ hr = core_if->hr_backup; ++ if (!hr) { ++ hr = DWC_ALLOC(sizeof(*hr)); ++ if (!hr) { ++ return -DWC_E_NO_MEMORY; ++ } ++ core_if->hr_backup = hr; ++ } ++ ++ hr->hcfg_local = ++ DWC_READ_REG32(&core_if->host_if->host_global_regs->hcfg); ++ hr->haintmsk_local = ++ DWC_READ_REG32(&core_if->host_if->host_global_regs->haintmsk); ++ for (i = 0; i < dwc_otg_get_param_host_channels(core_if); ++i) { ++ hr->hcintmsk_local[i] = ++ DWC_READ_REG32(&core_if->host_if->hc_regs[i]->hcintmsk); ++ } ++ hr->hprt0_local = DWC_READ_REG32(core_if->host_if->hprt0); ++ hr->hfir_local = ++ DWC_READ_REG32(&core_if->host_if->host_global_regs->hfir); ++ ++ DWC_DEBUGPL(DBG_ANY, ++ "=============Backing Host registers===============\n"); ++ DWC_DEBUGPL(DBG_ANY, "Backed up hcfg = %08x\n", ++ hr->hcfg_local); ++ DWC_DEBUGPL(DBG_ANY, "Backed up haintmsk = %08x\n", hr->haintmsk_local); ++ for (i = 0; i < dwc_otg_get_param_host_channels(core_if); ++i) { ++ DWC_DEBUGPL(DBG_ANY, "Backed up hcintmsk[%02d]=%08x\n", i, ++ hr->hcintmsk_local[i]); ++ } ++ DWC_DEBUGPL(DBG_ANY, "Backed up hprt0 = %08x\n", ++ hr->hprt0_local); ++ DWC_DEBUGPL(DBG_ANY, "Backed up hfir = %08x\n", ++ hr->hfir_local); ++ ++ return 0; ++} ++ ++int dwc_otg_restore_global_regs(dwc_otg_core_if_t *core_if) ++{ ++ struct dwc_otg_global_regs_backup *gr; ++ int i; ++ ++ gr = core_if->gr_backup; ++ if (!gr) { ++ return -DWC_E_INVALID; ++ } ++ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gotgctl, gr->gotgctl_local); ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, gr->gintmsk_local); ++ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, gr->gusbcfg_local); ++ DWC_WRITE_REG32(&core_if->core_global_regs->gahbcfg, gr->gahbcfg_local); ++ DWC_WRITE_REG32(&core_if->core_global_regs->grxfsiz, gr->grxfsiz_local); ++ DWC_WRITE_REG32(&core_if->core_global_regs->gnptxfsiz, ++ gr->gnptxfsiz_local); ++ DWC_WRITE_REG32(&core_if->core_global_regs->hptxfsiz, ++ gr->hptxfsiz_local); ++ DWC_WRITE_REG32(&core_if->core_global_regs->gdfifocfg, ++ gr->gdfifocfg_local); ++ for (i = 0; i < MAX_EPS_CHANNELS; i++) { ++ DWC_WRITE_REG32(&core_if->core_global_regs->dtxfsiz[i], ++ gr->dtxfsiz_local[i]); ++ } ++ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF); ++ DWC_WRITE_REG32(core_if->host_if->hprt0, 0x0000100A); ++ DWC_WRITE_REG32(&core_if->core_global_regs->gahbcfg, ++ (gr->gahbcfg_local)); ++ return 0; ++} ++ ++int dwc_otg_restore_dev_regs(dwc_otg_core_if_t * core_if, int rem_wakeup) ++{ ++ struct dwc_otg_dev_regs_backup *dr; ++ int i; ++ ++ dr = core_if->dr_backup; ++ ++ if (!dr) { ++ return -DWC_E_INVALID; ++ } ++ ++ if (!rem_wakeup) { ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl, ++ dr->dctl); ++ } ++ ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->daintmsk, dr->daintmsk); ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->diepmsk, dr->diepmsk); ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->doepmsk, dr->doepmsk); ++ ++ for (i = 0; i < core_if->dev_if->num_in_eps; ++i) { ++ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[i]->dieptsiz, dr->dieptsiz[i]); ++ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[i]->diepdma, dr->diepdma[i]); ++ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[i]->diepctl, dr->diepctl[i]); ++ } ++ ++ return 0; ++} ++ ++int dwc_otg_restore_host_regs(dwc_otg_core_if_t * core_if, int reset) ++{ ++ struct dwc_otg_host_regs_backup *hr; ++ int i; ++ hr = core_if->hr_backup; ++ ++ if (!hr) { ++ return -DWC_E_INVALID; ++ } ++ ++ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hcfg, hr->hcfg_local); ++ //if (!reset) ++ //{ ++ // DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hfir, hr->hfir_local); ++ //} ++ ++ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->haintmsk, ++ hr->haintmsk_local); ++ for (i = 0; i < dwc_otg_get_param_host_channels(core_if); ++i) { ++ DWC_WRITE_REG32(&core_if->host_if->hc_regs[i]->hcintmsk, ++ hr->hcintmsk_local[i]); ++ } ++ ++ return 0; ++} ++ ++int restore_lpm_i2c_regs(dwc_otg_core_if_t * core_if) ++{ ++ struct dwc_otg_global_regs_backup *gr; ++ ++ gr = core_if->gr_backup; ++ ++ /* Restore values for LPM and I2C */ ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg, gr->glpmcfg_local); ++#endif ++ DWC_WRITE_REG32(&core_if->core_global_regs->gi2cctl, gr->gi2cctl_local); ++ ++ return 0; ++} ++ ++int restore_essential_regs(dwc_otg_core_if_t * core_if, int rmode, int is_host) ++{ ++ struct dwc_otg_global_regs_backup *gr; ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ gahbcfg_data_t gahbcfg = {.d32 = 0 }; ++ gusbcfg_data_t gusbcfg = {.d32 = 0 }; ++ gintmsk_data_t gintmsk = {.d32 = 0 }; ++ ++ /* Restore LPM and I2C registers */ ++ restore_lpm_i2c_regs(core_if); ++ ++ /* Set PCGCCTL to 0 */ ++ DWC_WRITE_REG32(core_if->pcgcctl, 0x00000000); ++ ++ gr = core_if->gr_backup; ++ /* Load restore values for [31:14] bits */ ++ DWC_WRITE_REG32(core_if->pcgcctl, ++ ((gr->pcgcctl_local & 0xffffc000) | 0x00020000)); ++ ++ /* Umnask global Interrupt in GAHBCFG and restore it */ ++ gahbcfg.d32 = gr->gahbcfg_local; ++ gahbcfg.b.glblintrmsk = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gahbcfg, gahbcfg.d32); ++ ++ /* Clear all pending interupts */ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF); ++ ++ /* Unmask restore done interrupt */ ++ gintmsk.b.restoredone = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, gintmsk.d32); ++ ++ /* Restore GUSBCFG and HCFG/DCFG */ ++ gusbcfg.d32 = core_if->gr_backup->gusbcfg_local; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, gusbcfg.d32); ++ ++ if (is_host) { ++ hcfg_data_t hcfg = {.d32 = 0 }; ++ hcfg.d32 = core_if->hr_backup->hcfg_local; ++ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hcfg, ++ hcfg.d32); ++ ++ /* Load restore values for [31:14] bits */ ++ pcgcctl.d32 = gr->pcgcctl_local & 0xffffc000; ++ pcgcctl.d32 = gr->pcgcctl_local | 0x00020000; ++ ++ if (rmode) ++ pcgcctl.b.restoremode = 1; ++ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32); ++ dwc_udelay(10); ++ ++ /* Load restore values for [31:14] bits and set EssRegRestored bit */ ++ pcgcctl.d32 = gr->pcgcctl_local | 0xffffc000; ++ pcgcctl.d32 = gr->pcgcctl_local & 0xffffc000; ++ pcgcctl.b.ess_reg_restored = 1; ++ if (rmode) ++ pcgcctl.b.restoremode = 1; ++ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32); ++ } else { ++ dcfg_data_t dcfg = {.d32 = 0 }; ++ dcfg.d32 = core_if->dr_backup->dcfg; ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg, dcfg.d32); ++ ++ /* Load restore values for [31:14] bits */ ++ pcgcctl.d32 = gr->pcgcctl_local & 0xffffc000; ++ pcgcctl.d32 = gr->pcgcctl_local | 0x00020000; ++ if (!rmode) { ++ pcgcctl.d32 |= 0x208; ++ } ++ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32); ++ dwc_udelay(10); ++ ++ /* Load restore values for [31:14] bits */ ++ pcgcctl.d32 = gr->pcgcctl_local & 0xffffc000; ++ pcgcctl.d32 = gr->pcgcctl_local | 0x00020000; ++ pcgcctl.b.ess_reg_restored = 1; ++ if (!rmode) ++ pcgcctl.d32 |= 0x208; ++ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32); ++ } ++ ++ return 0; ++} ++ ++/** ++ * Initializes the FSLSPClkSel field of the HCFG register depending on the PHY ++ * type. ++ */ ++static void init_fslspclksel(dwc_otg_core_if_t * core_if) ++{ ++ uint32_t val; ++ hcfg_data_t hcfg; ++ ++ if (((core_if->hwcfg2.b.hs_phy_type == 2) && ++ (core_if->hwcfg2.b.fs_phy_type == 1) && ++ (core_if->core_params->ulpi_fs_ls)) || ++ (core_if->core_params->phy_type == DWC_PHY_TYPE_PARAM_FS)) { ++ /* Full speed PHY */ ++ val = DWC_HCFG_48_MHZ; ++ } else { ++ /* High speed PHY running at full speed or high speed */ ++ val = DWC_HCFG_30_60_MHZ; ++ } ++ ++ DWC_DEBUGPL(DBG_CIL, "Initializing HCFG.FSLSPClkSel to 0x%1x\n", val); ++ hcfg.d32 = DWC_READ_REG32(&core_if->host_if->host_global_regs->hcfg); ++ hcfg.b.fslspclksel = val; ++ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hcfg, hcfg.d32); ++} ++ ++/** ++ * Initializes the DevSpd field of the DCFG register depending on the PHY type ++ * and the enumeration speed of the device. ++ */ ++static void init_devspd(dwc_otg_core_if_t * core_if) ++{ ++ uint32_t val; ++ dcfg_data_t dcfg; ++ ++ if (((core_if->hwcfg2.b.hs_phy_type == 2) && ++ (core_if->hwcfg2.b.fs_phy_type == 1) && ++ (core_if->core_params->ulpi_fs_ls)) || ++ (core_if->core_params->phy_type == DWC_PHY_TYPE_PARAM_FS)) { ++ /* Full speed PHY */ ++ val = 0x3; ++ } else if (core_if->core_params->speed == DWC_SPEED_PARAM_FULL) { ++ /* High speed PHY running at full speed */ ++ val = 0x1; ++ } else { ++ /* High speed PHY running at high speed */ ++ val = 0x0; ++ } ++ ++ DWC_DEBUGPL(DBG_CIL, "Initializing DCFG.DevSpd to 0x%1x\n", val); ++ ++ dcfg.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg); ++ dcfg.b.devspd = val; ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg, dcfg.d32); ++} ++ ++/** ++ * This function calculates the number of IN EPS ++ * using GHWCFG1 and GHWCFG2 registers values ++ * ++ * @param core_if Programming view of the DWC_otg controller ++ */ ++static uint32_t calc_num_in_eps(dwc_otg_core_if_t * core_if) ++{ ++ uint32_t num_in_eps = 0; ++ uint32_t num_eps = core_if->hwcfg2.b.num_dev_ep; ++ uint32_t hwcfg1 = core_if->hwcfg1.d32 >> 3; ++ uint32_t num_tx_fifos = core_if->hwcfg4.b.num_in_eps; ++ int i; ++ ++ for (i = 0; i < num_eps; ++i) { ++ if (!(hwcfg1 & 0x1)) ++ num_in_eps++; ++ ++ hwcfg1 >>= 2; ++ } ++ ++ if (core_if->hwcfg4.b.ded_fifo_en) { ++ num_in_eps = ++ (num_in_eps > num_tx_fifos) ? num_tx_fifos : num_in_eps; ++ } ++ ++ return num_in_eps; ++} ++ ++/** ++ * This function calculates the number of OUT EPS ++ * using GHWCFG1 and GHWCFG2 registers values ++ * ++ * @param core_if Programming view of the DWC_otg controller ++ */ ++static uint32_t calc_num_out_eps(dwc_otg_core_if_t * core_if) ++{ ++ uint32_t num_out_eps = 0; ++ uint32_t num_eps = core_if->hwcfg2.b.num_dev_ep; ++ uint32_t hwcfg1 = core_if->hwcfg1.d32 >> 2; ++ int i; ++ ++ for (i = 0; i < num_eps; ++i) { ++ if (!(hwcfg1 & 0x1)) ++ num_out_eps++; ++ ++ hwcfg1 >>= 2; ++ } ++ return num_out_eps; ++} ++ ++/** ++ * This function initializes the DWC_otg controller registers and ++ * prepares the core for device mode or host mode operation. ++ * ++ * @param core_if Programming view of the DWC_otg controller ++ * ++ */ ++void dwc_otg_core_init(dwc_otg_core_if_t * core_if) ++{ ++ int i = 0; ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ gahbcfg_data_t ahbcfg = {.d32 = 0 }; ++ gusbcfg_data_t usbcfg = {.d32 = 0 }; ++ gi2cctl_data_t i2cctl = {.d32 = 0 }; ++ ++ DWC_DEBUGPL(DBG_CILV, "dwc_otg_core_init(%p) regs at %p\n", ++ core_if, global_regs); ++ ++ /* Common Initialization */ ++ usbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg); ++ ++ /* Program the ULPI External VBUS bit if needed */ ++ usbcfg.b.ulpi_ext_vbus_drv = ++ (core_if->core_params->phy_ulpi_ext_vbus == ++ DWC_PHY_ULPI_EXTERNAL_VBUS) ? 1 : 0; ++ ++ /* Set external TS Dline pulsing */ ++ usbcfg.b.term_sel_dl_pulse = ++ (core_if->core_params->ts_dline == 1) ? 1 : 0; ++ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32); ++ ++ /* Reset the Controller */ ++ dwc_otg_core_reset(core_if); ++ ++ core_if->adp_enable = core_if->core_params->adp_supp_enable; ++ core_if->power_down = core_if->core_params->power_down; ++ core_if->otg_sts = 0; ++ ++ /* Initialize parameters from Hardware configuration registers. */ ++ dev_if->num_in_eps = calc_num_in_eps(core_if); ++ dev_if->num_out_eps = calc_num_out_eps(core_if); ++ ++ DWC_DEBUGPL(DBG_CIL, "num_dev_perio_in_ep=%d\n", ++ core_if->hwcfg4.b.num_dev_perio_in_ep); ++ ++ for (i = 0; i < core_if->hwcfg4.b.num_dev_perio_in_ep; i++) { ++ dev_if->perio_tx_fifo_size[i] = ++ DWC_READ_REG32(&global_regs->dtxfsiz[i]) >> 16; ++ DWC_DEBUGPL(DBG_CIL, "Periodic Tx FIFO SZ #%d=0x%0x\n", ++ i, dev_if->perio_tx_fifo_size[i]); ++ } ++ ++ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) { ++ dev_if->tx_fifo_size[i] = ++ DWC_READ_REG32(&global_regs->dtxfsiz[i]) >> 16; ++ DWC_DEBUGPL(DBG_CIL, "Tx FIFO SZ #%d=0x%0x\n", ++ i, dev_if->tx_fifo_size[i]); ++ } ++ ++ core_if->total_fifo_size = core_if->hwcfg3.b.dfifo_depth; ++ core_if->rx_fifo_size = DWC_READ_REG32(&global_regs->grxfsiz); ++ core_if->nperio_tx_fifo_size = ++ DWC_READ_REG32(&global_regs->gnptxfsiz) >> 16; ++ ++ DWC_DEBUGPL(DBG_CIL, "Total FIFO SZ=%d\n", core_if->total_fifo_size); ++ DWC_DEBUGPL(DBG_CIL, "Rx FIFO SZ=%d\n", core_if->rx_fifo_size); ++ DWC_DEBUGPL(DBG_CIL, "NP Tx FIFO SZ=%d\n", ++ core_if->nperio_tx_fifo_size); ++ ++ /* This programming sequence needs to happen in FS mode before any other ++ * programming occurs */ ++ if ((core_if->core_params->speed == DWC_SPEED_PARAM_FULL) && ++ (core_if->core_params->phy_type == DWC_PHY_TYPE_PARAM_FS)) { ++ /* If FS mode with FS PHY */ ++ ++ /* core_init() is now called on every switch so only call the ++ * following for the first time through. */ ++ if (!core_if->phy_init_done) { ++ core_if->phy_init_done = 1; ++ DWC_DEBUGPL(DBG_CIL, "FS_PHY detected\n"); ++ usbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg); ++ usbcfg.b.physel = 1; ++ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32); ++ ++ /* Reset after a PHY select */ ++ dwc_otg_core_reset(core_if); ++ } ++ ++ /* Program DCFG.DevSpd or HCFG.FSLSPclkSel to 48Mhz in FS. Also ++ * do this on HNP Dev/Host mode switches (done in dev_init and ++ * host_init). */ ++ if (dwc_otg_is_host_mode(core_if)) { ++ init_fslspclksel(core_if); ++ } else { ++ init_devspd(core_if); ++ } ++ ++ if (core_if->core_params->i2c_enable) { ++ DWC_DEBUGPL(DBG_CIL, "FS_PHY Enabling I2c\n"); ++ /* Program GUSBCFG.OtgUtmifsSel to I2C */ ++ usbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg); ++ usbcfg.b.otgutmifssel = 1; ++ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32); ++ ++ /* Program GI2CCTL.I2CEn */ ++ i2cctl.d32 = DWC_READ_REG32(&global_regs->gi2cctl); ++ i2cctl.b.i2cdevaddr = 1; ++ i2cctl.b.i2cen = 0; ++ DWC_WRITE_REG32(&global_regs->gi2cctl, i2cctl.d32); ++ i2cctl.b.i2cen = 1; ++ DWC_WRITE_REG32(&global_regs->gi2cctl, i2cctl.d32); ++ } ++ ++ } /* endif speed == DWC_SPEED_PARAM_FULL */ ++ else { ++ /* High speed PHY. */ ++ if (!core_if->phy_init_done) { ++ core_if->phy_init_done = 1; ++ /* HS PHY parameters. These parameters are preserved ++ * during soft reset so only program the first time. Do ++ * a soft reset immediately after setting phyif. */ ++ ++ if (core_if->core_params->phy_type == 2) { ++ /* ULPI interface */ ++ usbcfg.b.ulpi_utmi_sel = 1; ++ usbcfg.b.phyif = 0; ++ usbcfg.b.ddrsel = ++ core_if->core_params->phy_ulpi_ddr; ++ } else if (core_if->core_params->phy_type == 1) { ++ /* UTMI+ interface */ ++ usbcfg.b.ulpi_utmi_sel = 0; ++ if (core_if->core_params->phy_utmi_width == 16) { ++ usbcfg.b.phyif = 1; ++ ++ } else { ++ usbcfg.b.phyif = 0; ++ } ++ } else { ++ DWC_ERROR("FS PHY TYPE\n"); ++ } ++ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32); ++ /* Reset after setting the PHY parameters */ ++ dwc_otg_core_reset(core_if); ++ } ++ } ++ ++ if ((core_if->hwcfg2.b.hs_phy_type == 2) && ++ (core_if->hwcfg2.b.fs_phy_type == 1) && ++ (core_if->core_params->ulpi_fs_ls)) { ++ DWC_DEBUGPL(DBG_CIL, "Setting ULPI FSLS\n"); ++ usbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg); ++ usbcfg.b.ulpi_fsls = 1; ++ usbcfg.b.ulpi_clk_sus_m = 1; ++ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32); ++ } else { ++ usbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg); ++ usbcfg.b.ulpi_fsls = 0; ++ usbcfg.b.ulpi_clk_sus_m = 0; ++ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32); ++ } ++ ++ /* Program the GAHBCFG Register. */ ++ switch (core_if->hwcfg2.b.architecture) { ++ ++ case DWC_SLAVE_ONLY_ARCH: ++ DWC_DEBUGPL(DBG_CIL, "Slave Only Mode\n"); ++ ahbcfg.b.nptxfemplvl_txfemplvl = ++ DWC_GAHBCFG_TXFEMPTYLVL_HALFEMPTY; ++ ahbcfg.b.ptxfemplvl = DWC_GAHBCFG_TXFEMPTYLVL_HALFEMPTY; ++ core_if->dma_enable = 0; ++ core_if->dma_desc_enable = 0; ++ break; ++ ++ case DWC_EXT_DMA_ARCH: ++ DWC_DEBUGPL(DBG_CIL, "External DMA Mode\n"); ++ { ++ uint8_t brst_sz = core_if->core_params->dma_burst_size; ++ ahbcfg.b.hburstlen = 0; ++ while (brst_sz > 1) { ++ ahbcfg.b.hburstlen++; ++ brst_sz >>= 1; ++ } ++ } ++ core_if->dma_enable = (core_if->core_params->dma_enable != 0); ++ core_if->dma_desc_enable = ++ (core_if->core_params->dma_desc_enable != 0); ++ break; ++ ++ case DWC_INT_DMA_ARCH: ++ DWC_DEBUGPL(DBG_CIL, "Internal DMA Mode\n"); ++ /* Old value was DWC_GAHBCFG_INT_DMA_BURST_INCR - done for ++ Host mode ISOC in issue fix - vahrama */ ++ /* Broadcom had altered to (1<<3)|(0<<0) - WRESP=1, max 4 beats */ ++ ahbcfg.b.hburstlen = (1<<3)|(0<<0);//DWC_GAHBCFG_INT_DMA_BURST_INCR4; ++ core_if->dma_enable = (core_if->core_params->dma_enable != 0); ++ core_if->dma_desc_enable = ++ (core_if->core_params->dma_desc_enable != 0); ++ break; ++ ++ } ++ if (core_if->dma_enable) { ++ if (core_if->dma_desc_enable) { ++ DWC_PRINTF("Using Descriptor DMA mode\n"); ++ } else { ++ DWC_PRINTF("Using Buffer DMA mode\n"); ++ ++ } ++ } else { ++ DWC_PRINTF("Using Slave mode\n"); ++ core_if->dma_desc_enable = 0; ++ } ++ ++ if (core_if->core_params->ahb_single) { ++ ahbcfg.b.ahbsingle = 1; ++ } ++ ++ ahbcfg.b.dmaenable = core_if->dma_enable; ++ DWC_WRITE_REG32(&global_regs->gahbcfg, ahbcfg.d32); ++ ++ core_if->en_multiple_tx_fifo = core_if->hwcfg4.b.ded_fifo_en; ++ ++ core_if->pti_enh_enable = core_if->core_params->pti_enable != 0; ++ core_if->multiproc_int_enable = core_if->core_params->mpi_enable; ++ DWC_PRINTF("Periodic Transfer Interrupt Enhancement - %s\n", ++ ((core_if->pti_enh_enable) ? "enabled" : "disabled")); ++ DWC_PRINTF("Multiprocessor Interrupt Enhancement - %s\n", ++ ((core_if->multiproc_int_enable) ? "enabled" : "disabled")); ++ ++ /* ++ * Program the GUSBCFG register. ++ */ ++ usbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg); ++ ++ switch (core_if->hwcfg2.b.op_mode) { ++ case DWC_MODE_HNP_SRP_CAPABLE: ++ usbcfg.b.hnpcap = (core_if->core_params->otg_cap == ++ DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE); ++ usbcfg.b.srpcap = (core_if->core_params->otg_cap != ++ DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE); ++ break; ++ ++ case DWC_MODE_SRP_ONLY_CAPABLE: ++ usbcfg.b.hnpcap = 0; ++ usbcfg.b.srpcap = (core_if->core_params->otg_cap != ++ DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE); ++ break; ++ ++ case DWC_MODE_NO_HNP_SRP_CAPABLE: ++ usbcfg.b.hnpcap = 0; ++ usbcfg.b.srpcap = 0; ++ break; ++ ++ case DWC_MODE_SRP_CAPABLE_DEVICE: ++ usbcfg.b.hnpcap = 0; ++ usbcfg.b.srpcap = (core_if->core_params->otg_cap != ++ DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE); ++ break; ++ ++ case DWC_MODE_NO_SRP_CAPABLE_DEVICE: ++ usbcfg.b.hnpcap = 0; ++ usbcfg.b.srpcap = 0; ++ break; ++ ++ case DWC_MODE_SRP_CAPABLE_HOST: ++ usbcfg.b.hnpcap = 0; ++ usbcfg.b.srpcap = (core_if->core_params->otg_cap != ++ DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE); ++ break; ++ ++ case DWC_MODE_NO_SRP_CAPABLE_HOST: ++ usbcfg.b.hnpcap = 0; ++ usbcfg.b.srpcap = 0; ++ break; ++ } ++ ++ DWC_WRITE_REG32(&global_regs->gusbcfg, usbcfg.d32); ++ ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ if (core_if->core_params->lpm_enable) { ++ glpmcfg_data_t lpmcfg = {.d32 = 0 }; ++ ++ /* To enable LPM support set lpm_cap_en bit */ ++ lpmcfg.b.lpm_cap_en = 1; ++ ++ /* Make AppL1Res ACK */ ++ lpmcfg.b.appl_resp = 1; ++ ++ /* Retry 3 times */ ++ lpmcfg.b.retry_count = 3; ++ ++ DWC_MODIFY_REG32(&core_if->core_global_regs->glpmcfg, ++ 0, lpmcfg.d32); ++ ++ } ++#endif ++ if (core_if->core_params->ic_usb_cap) { ++ gusbcfg_data_t gusbcfg = {.d32 = 0 }; ++ gusbcfg.b.ic_usb_cap = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gusbcfg, ++ 0, gusbcfg.d32); ++ } ++ { ++ gotgctl_data_t gotgctl = {.d32 = 0 }; ++ gotgctl.b.otgver = core_if->core_params->otg_ver; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gotgctl, 0, ++ gotgctl.d32); ++ /* Set OTG version supported */ ++ core_if->otg_ver = core_if->core_params->otg_ver; ++ DWC_PRINTF("OTG VER PARAM: %d, OTG VER FLAG: %d\n", ++ core_if->core_params->otg_ver, core_if->otg_ver); ++ } ++ ++ ++ /* Enable common interrupts */ ++ dwc_otg_enable_common_interrupts(core_if); ++ ++ /* Do device or host intialization based on mode during PCD ++ * and HCD initialization */ ++ if (dwc_otg_is_host_mode(core_if)) { ++ DWC_DEBUGPL(DBG_ANY, "Host Mode\n"); ++ core_if->op_state = A_HOST; ++ } else { ++ DWC_DEBUGPL(DBG_ANY, "Device Mode\n"); ++ core_if->op_state = B_PERIPHERAL; ++#ifdef DWC_DEVICE_ONLY ++ dwc_otg_core_dev_init(core_if); ++#endif ++ } ++} ++ ++/** ++ * This function enables the Device mode interrupts. ++ * ++ * @param core_if Programming view of DWC_otg controller ++ */ ++void dwc_otg_enable_device_interrupts(dwc_otg_core_if_t * core_if) ++{ ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ ++ DWC_DEBUGPL(DBG_CIL, "%s()\n", __func__); ++ ++ /* Disable all interrupts. */ ++ DWC_WRITE_REG32(&global_regs->gintmsk, 0); ++ ++ /* Clear any pending interrupts */ ++ DWC_WRITE_REG32(&global_regs->gintsts, 0xFFFFFFFF); ++ ++ /* Enable the common interrupts */ ++ dwc_otg_enable_common_interrupts(core_if); ++ ++ /* Enable interrupts */ ++ intr_mask.b.usbreset = 1; ++ intr_mask.b.enumdone = 1; ++ /* Disable Disconnect interrupt in Device mode */ ++ intr_mask.b.disconnect = 0; ++ ++ if (!core_if->multiproc_int_enable) { ++ intr_mask.b.inepintr = 1; ++ intr_mask.b.outepintr = 1; ++ } ++ ++ intr_mask.b.erlysuspend = 1; ++ ++ if (core_if->en_multiple_tx_fifo == 0) { ++ intr_mask.b.epmismatch = 1; ++ } ++ ++ //intr_mask.b.incomplisoout = 1; ++ intr_mask.b.incomplisoin = 1; ++ ++/* Enable the ignore frame number for ISOC xfers - MAS */ ++/* Disable to support high bandwith ISOC transfers - manukz */ ++#if 0 ++#ifdef DWC_UTE_PER_IO ++ if (core_if->dma_enable) { ++ if (core_if->dma_desc_enable) { ++ dctl_data_t dctl1 = {.d32 = 0 }; ++ dctl1.b.ifrmnum = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs-> ++ dctl, 0, dctl1.d32); ++ DWC_DEBUG("----Enabled Ignore frame number (0x%08x)", ++ DWC_READ_REG32(&core_if->dev_if-> ++ dev_global_regs->dctl)); ++ } ++ } ++#endif ++#endif ++#ifdef DWC_EN_ISOC ++ if (core_if->dma_enable) { ++ if (core_if->dma_desc_enable == 0) { ++ if (core_if->pti_enh_enable) { ++ dctl_data_t dctl = {.d32 = 0 }; ++ dctl.b.ifrmnum = 1; ++ DWC_MODIFY_REG32(&core_if-> ++ dev_if->dev_global_regs->dctl, ++ 0, dctl.d32); ++ } else { ++ intr_mask.b.incomplisoin = 1; ++ intr_mask.b.incomplisoout = 1; ++ } ++ } ++ } else { ++ intr_mask.b.incomplisoin = 1; ++ intr_mask.b.incomplisoout = 1; ++ } ++#endif /* DWC_EN_ISOC */ ++ ++ /** @todo NGS: Should this be a module parameter? */ ++#ifdef USE_PERIODIC_EP ++ intr_mask.b.isooutdrop = 1; ++ intr_mask.b.eopframe = 1; ++ intr_mask.b.incomplisoin = 1; ++ intr_mask.b.incomplisoout = 1; ++#endif ++ ++ DWC_MODIFY_REG32(&global_regs->gintmsk, intr_mask.d32, intr_mask.d32); ++ ++ DWC_DEBUGPL(DBG_CIL, "%s() gintmsk=%0x\n", __func__, ++ DWC_READ_REG32(&global_regs->gintmsk)); ++} ++ ++/** ++ * This function initializes the DWC_otg controller registers for ++ * device mode. ++ * ++ * @param core_if Programming view of DWC_otg controller ++ * ++ */ ++void dwc_otg_core_dev_init(dwc_otg_core_if_t * core_if) ++{ ++ int i; ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ dwc_otg_core_params_t *params = core_if->core_params; ++ dcfg_data_t dcfg = {.d32 = 0 }; ++ depctl_data_t diepctl = {.d32 = 0 }; ++ grstctl_t resetctl = {.d32 = 0 }; ++ uint32_t rx_fifo_size; ++ fifosize_data_t nptxfifosize; ++ fifosize_data_t txfifosize; ++ dthrctl_data_t dthrctl; ++ fifosize_data_t ptxfifosize; ++ uint16_t rxfsiz, nptxfsiz; ++ gdfifocfg_data_t gdfifocfg = {.d32 = 0 }; ++ hwcfg3_data_t hwcfg3 = {.d32 = 0 }; ++ ++ /* Restart the Phy Clock */ ++ DWC_WRITE_REG32(core_if->pcgcctl, 0); ++ ++ /* Device configuration register */ ++ init_devspd(core_if); ++ dcfg.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dcfg); ++ dcfg.b.descdma = (core_if->dma_desc_enable) ? 1 : 0; ++ dcfg.b.perfrint = DWC_DCFG_FRAME_INTERVAL_80; ++ /* Enable Device OUT NAK in case of DDMA mode*/ ++ if (core_if->core_params->dev_out_nak) { ++ dcfg.b.endevoutnak = 1; ++ } ++ ++ if (core_if->core_params->cont_on_bna) { ++ dctl_data_t dctl = {.d32 = 0 }; ++ dctl.b.encontonbna = 1; ++ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dctl, 0, dctl.d32); ++ } ++ ++ ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->dcfg, dcfg.d32); ++ ++ /* Configure data FIFO sizes */ ++ if (core_if->hwcfg2.b.dynamic_fifo && params->enable_dynamic_fifo) { ++ DWC_DEBUGPL(DBG_CIL, "Total FIFO Size=%d\n", ++ core_if->total_fifo_size); ++ DWC_DEBUGPL(DBG_CIL, "Rx FIFO Size=%d\n", ++ params->dev_rx_fifo_size); ++ DWC_DEBUGPL(DBG_CIL, "NP Tx FIFO Size=%d\n", ++ params->dev_nperio_tx_fifo_size); ++ ++ /* Rx FIFO */ ++ DWC_DEBUGPL(DBG_CIL, "initial grxfsiz=%08x\n", ++ DWC_READ_REG32(&global_regs->grxfsiz)); ++ ++#ifdef DWC_UTE_CFI ++ core_if->pwron_rxfsiz = DWC_READ_REG32(&global_regs->grxfsiz); ++ core_if->init_rxfsiz = params->dev_rx_fifo_size; ++#endif ++ rx_fifo_size = params->dev_rx_fifo_size; ++ DWC_WRITE_REG32(&global_regs->grxfsiz, rx_fifo_size); ++ ++ DWC_DEBUGPL(DBG_CIL, "new grxfsiz=%08x\n", ++ DWC_READ_REG32(&global_regs->grxfsiz)); ++ ++ /** Set Periodic Tx FIFO Mask all bits 0 */ ++ core_if->p_tx_msk = 0; ++ ++ /** Set Tx FIFO Mask all bits 0 */ ++ core_if->tx_msk = 0; ++ ++ if (core_if->en_multiple_tx_fifo == 0) { ++ /* Non-periodic Tx FIFO */ ++ DWC_DEBUGPL(DBG_CIL, "initial gnptxfsiz=%08x\n", ++ DWC_READ_REG32(&global_regs->gnptxfsiz)); ++ ++ nptxfifosize.b.depth = params->dev_nperio_tx_fifo_size; ++ nptxfifosize.b.startaddr = params->dev_rx_fifo_size; ++ ++ DWC_WRITE_REG32(&global_regs->gnptxfsiz, ++ nptxfifosize.d32); ++ ++ DWC_DEBUGPL(DBG_CIL, "new gnptxfsiz=%08x\n", ++ DWC_READ_REG32(&global_regs->gnptxfsiz)); ++ ++ /**@todo NGS: Fix Periodic FIFO Sizing! */ ++ /* ++ * Periodic Tx FIFOs These FIFOs are numbered from 1 to 15. ++ * Indexes of the FIFO size module parameters in the ++ * dev_perio_tx_fifo_size array and the FIFO size registers in ++ * the dptxfsiz array run from 0 to 14. ++ */ ++ /** @todo Finish debug of this */ ++ ptxfifosize.b.startaddr = ++ nptxfifosize.b.startaddr + nptxfifosize.b.depth; ++ for (i = 0; i < core_if->hwcfg4.b.num_dev_perio_in_ep; i++) { ++ ptxfifosize.b.depth = ++ params->dev_perio_tx_fifo_size[i]; ++ DWC_DEBUGPL(DBG_CIL, ++ "initial dtxfsiz[%d]=%08x\n", i, ++ DWC_READ_REG32(&global_regs->dtxfsiz ++ [i])); ++ DWC_WRITE_REG32(&global_regs->dtxfsiz[i], ++ ptxfifosize.d32); ++ DWC_DEBUGPL(DBG_CIL, "new dtxfsiz[%d]=%08x\n", ++ i, ++ DWC_READ_REG32(&global_regs->dtxfsiz ++ [i])); ++ ptxfifosize.b.startaddr += ptxfifosize.b.depth; ++ } ++ } else { ++ /* ++ * Tx FIFOs These FIFOs are numbered from 1 to 15. ++ * Indexes of the FIFO size module parameters in the ++ * dev_tx_fifo_size array and the FIFO size registers in ++ * the dtxfsiz array run from 0 to 14. ++ */ ++ ++ /* Non-periodic Tx FIFO */ ++ DWC_DEBUGPL(DBG_CIL, "initial gnptxfsiz=%08x\n", ++ DWC_READ_REG32(&global_regs->gnptxfsiz)); ++ ++#ifdef DWC_UTE_CFI ++ core_if->pwron_gnptxfsiz = ++ (DWC_READ_REG32(&global_regs->gnptxfsiz) >> 16); ++ core_if->init_gnptxfsiz = ++ params->dev_nperio_tx_fifo_size; ++#endif ++ nptxfifosize.b.depth = params->dev_nperio_tx_fifo_size; ++ nptxfifosize.b.startaddr = params->dev_rx_fifo_size; ++ ++ DWC_WRITE_REG32(&global_regs->gnptxfsiz, ++ nptxfifosize.d32); ++ ++ DWC_DEBUGPL(DBG_CIL, "new gnptxfsiz=%08x\n", ++ DWC_READ_REG32(&global_regs->gnptxfsiz)); ++ ++ txfifosize.b.startaddr = ++ nptxfifosize.b.startaddr + nptxfifosize.b.depth; ++ ++ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; i++) { ++ ++ txfifosize.b.depth = ++ params->dev_tx_fifo_size[i]; ++ ++ DWC_DEBUGPL(DBG_CIL, ++ "initial dtxfsiz[%d]=%08x\n", ++ i, ++ DWC_READ_REG32(&global_regs->dtxfsiz ++ [i])); ++ ++#ifdef DWC_UTE_CFI ++ core_if->pwron_txfsiz[i] = ++ (DWC_READ_REG32 ++ (&global_regs->dtxfsiz[i]) >> 16); ++ core_if->init_txfsiz[i] = ++ params->dev_tx_fifo_size[i]; ++#endif ++ DWC_WRITE_REG32(&global_regs->dtxfsiz[i], ++ txfifosize.d32); ++ ++ DWC_DEBUGPL(DBG_CIL, ++ "new dtxfsiz[%d]=%08x\n", ++ i, ++ DWC_READ_REG32(&global_regs->dtxfsiz ++ [i])); ++ ++ txfifosize.b.startaddr += txfifosize.b.depth; ++ } ++ if (core_if->snpsid <= OTG_CORE_REV_2_94a) { ++ /* Calculating DFIFOCFG for Device mode to include RxFIFO and NPTXFIFO */ ++ gdfifocfg.d32 = DWC_READ_REG32(&global_regs->gdfifocfg); ++ hwcfg3.d32 = DWC_READ_REG32(&global_regs->ghwcfg3); ++ gdfifocfg.b.gdfifocfg = (DWC_READ_REG32(&global_regs->ghwcfg3) >> 16); ++ DWC_WRITE_REG32(&global_regs->gdfifocfg, gdfifocfg.d32); ++ rxfsiz = (DWC_READ_REG32(&global_regs->grxfsiz) & 0x0000ffff); ++ nptxfsiz = (DWC_READ_REG32(&global_regs->gnptxfsiz) >> 16); ++ gdfifocfg.b.epinfobase = rxfsiz + nptxfsiz; ++ DWC_WRITE_REG32(&global_regs->gdfifocfg, gdfifocfg.d32); ++ } ++ } ++ ++ /* Flush the FIFOs */ ++ dwc_otg_flush_tx_fifo(core_if, 0x10); /* all Tx FIFOs */ ++ dwc_otg_flush_rx_fifo(core_if); ++ ++ /* Flush the Learning Queue. */ ++ resetctl.b.intknqflsh = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->grstctl, resetctl.d32); ++ ++ if (!core_if->core_params->en_multiple_tx_fifo && core_if->dma_enable) { ++ core_if->start_predict = 0; ++ for (i = 0; i<= core_if->dev_if->num_in_eps; ++i) { ++ core_if->nextep_seq[i] = 0xff; // 0xff - EP not active ++ } ++ core_if->nextep_seq[0] = 0; ++ core_if->first_in_nextep_seq = 0; ++ diepctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[0]->diepctl); ++ diepctl.b.nextep = 0; ++ DWC_WRITE_REG32(&dev_if->in_ep_regs[0]->diepctl, diepctl.d32); ++ ++ /* Update IN Endpoint Mismatch Count by active IN NP EP count + 1 */ ++ dcfg.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dcfg); ++ dcfg.b.epmscnt = 2; ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->dcfg, dcfg.d32); ++ ++ DWC_DEBUGPL(DBG_CILV,"%s first_in_nextep_seq= %2d; nextep_seq[]:\n", ++ __func__, core_if->first_in_nextep_seq); ++ for (i=0; i <= core_if->dev_if->num_in_eps; i++) { ++ DWC_DEBUGPL(DBG_CILV, "%2d ", core_if->nextep_seq[i]); ++ } ++ DWC_DEBUGPL(DBG_CILV,"\n"); ++ } ++ ++ /* Clear all pending Device Interrupts */ ++ /** @todo - if the condition needed to be checked ++ * or in any case all pending interrutps should be cleared? ++ */ ++ if (core_if->multiproc_int_enable) { ++ for (i = 0; i < core_if->dev_if->num_in_eps; ++i) { ++ DWC_WRITE_REG32(&dev_if-> ++ dev_global_regs->diepeachintmsk[i], 0); ++ } ++ } ++ ++ for (i = 0; i < core_if->dev_if->num_out_eps; ++i) { ++ DWC_WRITE_REG32(&dev_if-> ++ dev_global_regs->doepeachintmsk[i], 0); ++ } ++ ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->deachint, 0xFFFFFFFF); ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->deachintmsk, 0); ++ } else { ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->diepmsk, 0); ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->doepmsk, 0); ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->daint, 0xFFFFFFFF); ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->daintmsk, 0); ++ } ++ ++ for (i = 0; i <= dev_if->num_in_eps; i++) { ++ depctl_data_t depctl; ++ depctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl); ++ if (depctl.b.epena) { ++ depctl.d32 = 0; ++ depctl.b.epdis = 1; ++ depctl.b.snak = 1; ++ } else { ++ depctl.d32 = 0; ++ } ++ ++ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepctl, depctl.d32); ++ ++ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->dieptsiz, 0); ++ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepdma, 0); ++ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepint, 0xFF); ++ } ++ ++ for (i = 0; i <= dev_if->num_out_eps; i++) { ++ depctl_data_t depctl; ++ depctl.d32 = DWC_READ_REG32(&dev_if->out_ep_regs[i]->doepctl); ++ if (depctl.b.epena) { ++ dctl_data_t dctl = {.d32 = 0 }; ++ gintmsk_data_t gintsts = {.d32 = 0 }; ++ doepint_data_t doepint = {.d32 = 0 }; ++ dctl.b.sgoutnak = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0, dctl.d32); ++ do { ++ dwc_udelay(10); ++ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts); ++ } while (!gintsts.b.goutnakeff); ++ gintsts.d32 = 0; ++ gintsts.b.goutnakeff = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ ++ depctl.d32 = 0; ++ depctl.b.epdis = 1; ++ depctl.b.snak = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[i]->doepctl, depctl.d32); ++ do { ++ dwc_udelay(10); ++ doepint.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ out_ep_regs[i]->doepint); ++ } while (!doepint.b.epdisabled); ++ ++ doepint.b.epdisabled = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[i]->doepint, doepint.d32); ++ ++ dctl.d32 = 0; ++ dctl.b.cgoutnak = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0, dctl.d32); ++ } else { ++ depctl.d32 = 0; ++ } ++ ++ DWC_WRITE_REG32(&dev_if->out_ep_regs[i]->doepctl, depctl.d32); ++ ++ DWC_WRITE_REG32(&dev_if->out_ep_regs[i]->doeptsiz, 0); ++ DWC_WRITE_REG32(&dev_if->out_ep_regs[i]->doepdma, 0); ++ DWC_WRITE_REG32(&dev_if->out_ep_regs[i]->doepint, 0xFF); ++ } ++ ++ if (core_if->en_multiple_tx_fifo && core_if->dma_enable) { ++ dev_if->non_iso_tx_thr_en = params->thr_ctl & 0x1; ++ dev_if->iso_tx_thr_en = (params->thr_ctl >> 1) & 0x1; ++ dev_if->rx_thr_en = (params->thr_ctl >> 2) & 0x1; ++ ++ dev_if->rx_thr_length = params->rx_thr_length; ++ dev_if->tx_thr_length = params->tx_thr_length; ++ ++ dev_if->setup_desc_index = 0; ++ ++ dthrctl.d32 = 0; ++ dthrctl.b.non_iso_thr_en = dev_if->non_iso_tx_thr_en; ++ dthrctl.b.iso_thr_en = dev_if->iso_tx_thr_en; ++ dthrctl.b.tx_thr_len = dev_if->tx_thr_length; ++ dthrctl.b.rx_thr_en = dev_if->rx_thr_en; ++ dthrctl.b.rx_thr_len = dev_if->rx_thr_length; ++ dthrctl.b.ahb_thr_ratio = params->ahb_thr_ratio; ++ ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->dtknqr3_dthrctl, ++ dthrctl.d32); ++ ++ DWC_DEBUGPL(DBG_CIL, ++ "Non ISO Tx Thr - %d\nISO Tx Thr - %d\nRx Thr - %d\nTx Thr Len - %d\nRx Thr Len - %d\n", ++ dthrctl.b.non_iso_thr_en, dthrctl.b.iso_thr_en, ++ dthrctl.b.rx_thr_en, dthrctl.b.tx_thr_len, ++ dthrctl.b.rx_thr_len); ++ ++ } ++ ++ dwc_otg_enable_device_interrupts(core_if); ++ ++ { ++ diepmsk_data_t msk = {.d32 = 0 }; ++ msk.b.txfifoundrn = 1; ++ if (core_if->multiproc_int_enable) { ++ DWC_MODIFY_REG32(&dev_if->dev_global_regs-> ++ diepeachintmsk[0], msk.d32, msk.d32); ++ } else { ++ DWC_MODIFY_REG32(&dev_if->dev_global_regs->diepmsk, ++ msk.d32, msk.d32); ++ } ++ } ++ ++ if (core_if->multiproc_int_enable) { ++ /* Set NAK on Babble */ ++ dctl_data_t dctl = {.d32 = 0 }; ++ dctl.b.nakonbble = 1; ++ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dctl, 0, dctl.d32); ++ } ++ ++ if (core_if->snpsid >= OTG_CORE_REV_2_94a) { ++ dctl_data_t dctl = {.d32 = 0 }; ++ dctl.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dctl); ++ dctl.b.sftdiscon = 0; ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->dctl, dctl.d32); ++ } ++} ++ ++/** ++ * This function enables the Host mode interrupts. ++ * ++ * @param core_if Programming view of DWC_otg controller ++ */ ++void dwc_otg_enable_host_interrupts(dwc_otg_core_if_t * core_if) ++{ ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ DWC_DEBUGPL(DBG_CIL, "%s(%p)\n", __func__, core_if); ++ ++ /* Disable all interrupts. */ ++ DWC_WRITE_REG32(&global_regs->gintmsk, 0); ++ ++ /* Clear any pending interrupts. */ ++ DWC_WRITE_REG32(&global_regs->gintsts, 0xFFFFFFFF); ++ ++ /* Enable the common interrupts */ ++ dwc_otg_enable_common_interrupts(core_if); ++ ++ /* ++ * Enable host mode interrupts without disturbing common ++ * interrupts. ++ */ ++ ++ intr_mask.b.disconnect = 1; ++ intr_mask.b.portintr = 1; ++ intr_mask.b.hcintr = 1; ++ ++ DWC_MODIFY_REG32(&global_regs->gintmsk, intr_mask.d32, intr_mask.d32); ++} ++ ++/** ++ * This function disables the Host Mode interrupts. ++ * ++ * @param core_if Programming view of DWC_otg controller ++ */ ++void dwc_otg_disable_host_interrupts(dwc_otg_core_if_t * core_if) ++{ ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ DWC_DEBUGPL(DBG_CILV, "%s()\n", __func__); ++ ++ /* ++ * Disable host mode interrupts without disturbing common ++ * interrupts. ++ */ ++ intr_mask.b.sofintr = 1; ++ intr_mask.b.portintr = 1; ++ intr_mask.b.hcintr = 1; ++ intr_mask.b.ptxfempty = 1; ++ intr_mask.b.nptxfempty = 1; ++ ++ DWC_MODIFY_REG32(&global_regs->gintmsk, intr_mask.d32, 0); ++} ++ ++/** ++ * This function initializes the DWC_otg controller registers for ++ * host mode. ++ * ++ * This function flushes the Tx and Rx FIFOs and it flushes any entries in the ++ * request queues. Host channels are reset to ensure that they are ready for ++ * performing transfers. ++ * ++ * @param core_if Programming view of DWC_otg controller ++ * ++ */ ++void dwc_otg_core_host_init(dwc_otg_core_if_t * core_if) ++{ ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ dwc_otg_host_if_t *host_if = core_if->host_if; ++ dwc_otg_core_params_t *params = core_if->core_params; ++ hprt0_data_t hprt0 = {.d32 = 0 }; ++ fifosize_data_t nptxfifosize; ++ fifosize_data_t ptxfifosize; ++ uint16_t rxfsiz, nptxfsiz, hptxfsiz; ++ gdfifocfg_data_t gdfifocfg = {.d32 = 0 }; ++ int i; ++ hcchar_data_t hcchar; ++ hcfg_data_t hcfg; ++ hfir_data_t hfir; ++ dwc_otg_hc_regs_t *hc_regs; ++ int num_channels; ++ gotgctl_data_t gotgctl = {.d32 = 0 }; ++ ++ DWC_DEBUGPL(DBG_CILV, "%s(%p)\n", __func__, core_if); ++ ++ /* Restart the Phy Clock */ ++ DWC_WRITE_REG32(core_if->pcgcctl, 0); ++ ++ /* Initialize Host Configuration Register */ ++ init_fslspclksel(core_if); ++ if (core_if->core_params->speed == DWC_SPEED_PARAM_FULL) { ++ hcfg.d32 = DWC_READ_REG32(&host_if->host_global_regs->hcfg); ++ hcfg.b.fslssupp = 1; ++ DWC_WRITE_REG32(&host_if->host_global_regs->hcfg, hcfg.d32); ++ ++ } ++ ++ /* This bit allows dynamic reloading of the HFIR register ++ * during runtime. This bit needs to be programmed during ++ * initial configuration and its value must not be changed ++ * during runtime.*/ ++ if (core_if->core_params->reload_ctl == 1) { ++ hfir.d32 = DWC_READ_REG32(&host_if->host_global_regs->hfir); ++ hfir.b.hfirrldctrl = 1; ++ DWC_WRITE_REG32(&host_if->host_global_regs->hfir, hfir.d32); ++ } ++ ++ if (core_if->core_params->dma_desc_enable) { ++ uint8_t op_mode = core_if->hwcfg2.b.op_mode; ++ if (! ++ (core_if->hwcfg4.b.desc_dma ++ && (core_if->snpsid >= OTG_CORE_REV_2_90a) ++ && ((op_mode == DWC_HWCFG2_OP_MODE_HNP_SRP_CAPABLE_OTG) ++ || (op_mode == DWC_HWCFG2_OP_MODE_SRP_ONLY_CAPABLE_OTG) ++ || (op_mode == ++ DWC_HWCFG2_OP_MODE_NO_HNP_SRP_CAPABLE_OTG) ++ || (op_mode == DWC_HWCFG2_OP_MODE_SRP_CAPABLE_HOST) ++ || (op_mode == ++ DWC_HWCFG2_OP_MODE_NO_SRP_CAPABLE_HOST)))) { ++ ++ DWC_ERROR("Host can't operate in Descriptor DMA mode.\n" ++ "Either core version is below 2.90a or " ++ "GHWCFG2, GHWCFG4 registers' values do not allow Descriptor DMA in host mode.\n" ++ "To run the driver in Buffer DMA host mode set dma_desc_enable " ++ "module parameter to 0.\n"); ++ return; ++ } ++ hcfg.d32 = DWC_READ_REG32(&host_if->host_global_regs->hcfg); ++ hcfg.b.descdma = 1; ++ DWC_WRITE_REG32(&host_if->host_global_regs->hcfg, hcfg.d32); ++ } ++ ++ /* Configure data FIFO sizes */ ++ if (core_if->hwcfg2.b.dynamic_fifo && params->enable_dynamic_fifo) { ++ DWC_DEBUGPL(DBG_CIL, "Total FIFO Size=%d\n", ++ core_if->total_fifo_size); ++ DWC_DEBUGPL(DBG_CIL, "Rx FIFO Size=%d\n", ++ params->host_rx_fifo_size); ++ DWC_DEBUGPL(DBG_CIL, "NP Tx FIFO Size=%d\n", ++ params->host_nperio_tx_fifo_size); ++ DWC_DEBUGPL(DBG_CIL, "P Tx FIFO Size=%d\n", ++ params->host_perio_tx_fifo_size); ++ ++ /* Rx FIFO */ ++ DWC_DEBUGPL(DBG_CIL, "initial grxfsiz=%08x\n", ++ DWC_READ_REG32(&global_regs->grxfsiz)); ++ DWC_WRITE_REG32(&global_regs->grxfsiz, ++ params->host_rx_fifo_size); ++ DWC_DEBUGPL(DBG_CIL, "new grxfsiz=%08x\n", ++ DWC_READ_REG32(&global_regs->grxfsiz)); ++ ++ /* Non-periodic Tx FIFO */ ++ DWC_DEBUGPL(DBG_CIL, "initial gnptxfsiz=%08x\n", ++ DWC_READ_REG32(&global_regs->gnptxfsiz)); ++ nptxfifosize.b.depth = params->host_nperio_tx_fifo_size; ++ nptxfifosize.b.startaddr = params->host_rx_fifo_size; ++ DWC_WRITE_REG32(&global_regs->gnptxfsiz, nptxfifosize.d32); ++ DWC_DEBUGPL(DBG_CIL, "new gnptxfsiz=%08x\n", ++ DWC_READ_REG32(&global_regs->gnptxfsiz)); ++ ++ /* Periodic Tx FIFO */ ++ DWC_DEBUGPL(DBG_CIL, "initial hptxfsiz=%08x\n", ++ DWC_READ_REG32(&global_regs->hptxfsiz)); ++ ptxfifosize.b.depth = params->host_perio_tx_fifo_size; ++ ptxfifosize.b.startaddr = ++ nptxfifosize.b.startaddr + nptxfifosize.b.depth; ++ DWC_WRITE_REG32(&global_regs->hptxfsiz, ptxfifosize.d32); ++ DWC_DEBUGPL(DBG_CIL, "new hptxfsiz=%08x\n", ++ DWC_READ_REG32(&global_regs->hptxfsiz)); ++ ++ if (core_if->en_multiple_tx_fifo ++ && core_if->snpsid <= OTG_CORE_REV_2_94a) { ++ /* Global DFIFOCFG calculation for Host mode - include RxFIFO, NPTXFIFO and HPTXFIFO */ ++ gdfifocfg.d32 = DWC_READ_REG32(&global_regs->gdfifocfg); ++ rxfsiz = (DWC_READ_REG32(&global_regs->grxfsiz) & 0x0000ffff); ++ nptxfsiz = (DWC_READ_REG32(&global_regs->gnptxfsiz) >> 16); ++ hptxfsiz = (DWC_READ_REG32(&global_regs->hptxfsiz) >> 16); ++ gdfifocfg.b.epinfobase = rxfsiz + nptxfsiz + hptxfsiz; ++ DWC_WRITE_REG32(&global_regs->gdfifocfg, gdfifocfg.d32); ++ } ++ } ++ ++ /* TODO - check this */ ++ /* Clear Host Set HNP Enable in the OTG Control Register */ ++ gotgctl.b.hstsethnpen = 1; ++ DWC_MODIFY_REG32(&global_regs->gotgctl, gotgctl.d32, 0); ++ /* Make sure the FIFOs are flushed. */ ++ dwc_otg_flush_tx_fifo(core_if, 0x10 /* all TX FIFOs */ ); ++ dwc_otg_flush_rx_fifo(core_if); ++ ++ /* Clear Host Set HNP Enable in the OTG Control Register */ ++ gotgctl.b.hstsethnpen = 1; ++ DWC_MODIFY_REG32(&global_regs->gotgctl, gotgctl.d32, 0); ++ ++ if (!core_if->core_params->dma_desc_enable) { ++ /* Flush out any leftover queued requests. */ ++ num_channels = core_if->core_params->host_channels; ++ ++ for (i = 0; i < num_channels; i++) { ++ hc_regs = core_if->host_if->hc_regs[i]; ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ hcchar.b.chen = 0; ++ hcchar.b.chdis = 1; ++ hcchar.b.epdir = 0; ++ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32); ++ } ++ ++ /* Halt all channels to put them into a known state. */ ++ for (i = 0; i < num_channels; i++) { ++ int count = 0; ++ hc_regs = core_if->host_if->hc_regs[i]; ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ hcchar.b.chen = 1; ++ hcchar.b.chdis = 1; ++ hcchar.b.epdir = 0; ++ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32); ++ DWC_DEBUGPL(DBG_HCDV, "%s: Halt channel %d regs %p\n", __func__, i, hc_regs); ++ do { ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ if (++count > 1000) { ++ DWC_ERROR ++ ("%s: Unable to clear halt on channel %d (timeout HCCHAR 0x%X @%p)\n", ++ __func__, i, hcchar.d32, &hc_regs->hcchar); ++ break; ++ } ++ dwc_udelay(1); ++ } while (hcchar.b.chen); ++ } ++ } ++ ++ /* Turn on the vbus power. */ ++ DWC_PRINTF("Init: Port Power? op_state=%d\n", core_if->op_state); ++ if (core_if->op_state == A_HOST) { ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ DWC_PRINTF("Init: Power Port (%d)\n", hprt0.b.prtpwr); ++ if (hprt0.b.prtpwr == 0) { ++ hprt0.b.prtpwr = 1; ++ DWC_WRITE_REG32(host_if->hprt0, hprt0.d32); ++ } ++ } ++ ++ dwc_otg_enable_host_interrupts(core_if); ++} ++ ++/** ++ * Prepares a host channel for transferring packets to/from a specific ++ * endpoint. The HCCHARn register is set up with the characteristics specified ++ * in _hc. Host channel interrupts that may need to be serviced while this ++ * transfer is in progress are enabled. ++ * ++ * @param core_if Programming view of DWC_otg controller ++ * @param hc Information needed to initialize the host channel ++ */ ++void dwc_otg_hc_init(dwc_otg_core_if_t * core_if, dwc_hc_t * hc) ++{ ++ hcintmsk_data_t hc_intr_mask; ++ hcchar_data_t hcchar; ++ hcsplt_data_t hcsplt; ++ ++ uint8_t hc_num = hc->hc_num; ++ dwc_otg_host_if_t *host_if = core_if->host_if; ++ dwc_otg_hc_regs_t *hc_regs = host_if->hc_regs[hc_num]; ++ ++ /* Clear old interrupt conditions for this host channel. */ ++ hc_intr_mask.d32 = 0xFFFFFFFF; ++ hc_intr_mask.b.reserved14_31 = 0; ++ DWC_WRITE_REG32(&hc_regs->hcint, hc_intr_mask.d32); ++ ++ /* Enable channel interrupts required for this transfer. */ ++ hc_intr_mask.d32 = 0; ++ hc_intr_mask.b.chhltd = 1; ++ if (core_if->dma_enable) { ++ /* For Descriptor DMA mode core halts the channel on AHB error. Interrupt is not required */ ++ if (!core_if->dma_desc_enable) ++ hc_intr_mask.b.ahberr = 1; ++ else { ++ if (hc->ep_type == DWC_OTG_EP_TYPE_ISOC) ++ hc_intr_mask.b.xfercompl = 1; ++ } ++ ++ if (hc->error_state && !hc->do_split && ++ hc->ep_type != DWC_OTG_EP_TYPE_ISOC) { ++ hc_intr_mask.b.ack = 1; ++ if (hc->ep_is_in) { ++ hc_intr_mask.b.datatglerr = 1; ++ if (hc->ep_type != DWC_OTG_EP_TYPE_INTR) { ++ hc_intr_mask.b.nak = 1; ++ } ++ } ++ } ++ } else { ++ switch (hc->ep_type) { ++ case DWC_OTG_EP_TYPE_CONTROL: ++ case DWC_OTG_EP_TYPE_BULK: ++ hc_intr_mask.b.xfercompl = 1; ++ hc_intr_mask.b.stall = 1; ++ hc_intr_mask.b.xacterr = 1; ++ hc_intr_mask.b.datatglerr = 1; ++ if (hc->ep_is_in) { ++ hc_intr_mask.b.bblerr = 1; ++ } else { ++ hc_intr_mask.b.nak = 1; ++ hc_intr_mask.b.nyet = 1; ++ if (hc->do_ping) { ++ hc_intr_mask.b.ack = 1; ++ } ++ } ++ ++ if (hc->do_split) { ++ hc_intr_mask.b.nak = 1; ++ if (hc->complete_split) { ++ hc_intr_mask.b.nyet = 1; ++ } else { ++ hc_intr_mask.b.ack = 1; ++ } ++ } ++ ++ if (hc->error_state) { ++ hc_intr_mask.b.ack = 1; ++ } ++ break; ++ case DWC_OTG_EP_TYPE_INTR: ++ hc_intr_mask.b.xfercompl = 1; ++ hc_intr_mask.b.nak = 1; ++ hc_intr_mask.b.stall = 1; ++ hc_intr_mask.b.xacterr = 1; ++ hc_intr_mask.b.datatglerr = 1; ++ hc_intr_mask.b.frmovrun = 1; ++ ++ if (hc->ep_is_in) { ++ hc_intr_mask.b.bblerr = 1; ++ } ++ if (hc->error_state) { ++ hc_intr_mask.b.ack = 1; ++ } ++ if (hc->do_split) { ++ if (hc->complete_split) { ++ hc_intr_mask.b.nyet = 1; ++ } else { ++ hc_intr_mask.b.ack = 1; ++ } ++ } ++ break; ++ case DWC_OTG_EP_TYPE_ISOC: ++ hc_intr_mask.b.xfercompl = 1; ++ hc_intr_mask.b.frmovrun = 1; ++ hc_intr_mask.b.ack = 1; ++ ++ if (hc->ep_is_in) { ++ hc_intr_mask.b.xacterr = 1; ++ hc_intr_mask.b.bblerr = 1; ++ } ++ break; ++ } ++ } ++ DWC_WRITE_REG32(&hc_regs->hcintmsk, hc_intr_mask.d32); ++ ++ /* ++ * Program the HCCHARn register with the endpoint characteristics for ++ * the current transfer. ++ */ ++ hcchar.d32 = 0; ++ hcchar.b.devaddr = hc->dev_addr; ++ hcchar.b.epnum = hc->ep_num; ++ hcchar.b.epdir = hc->ep_is_in; ++ hcchar.b.lspddev = (hc->speed == DWC_OTG_EP_SPEED_LOW); ++ hcchar.b.eptype = hc->ep_type; ++ hcchar.b.mps = hc->max_packet; ++ ++ DWC_WRITE_REG32(&host_if->hc_regs[hc_num]->hcchar, hcchar.d32); ++ ++ DWC_DEBUGPL(DBG_HCDV, "%s: Channel %d, Dev Addr %d, EP #%d\n", ++ __func__, hc->hc_num, hcchar.b.devaddr, hcchar.b.epnum); ++ DWC_DEBUGPL(DBG_HCDV, " Is In %d, Is Low Speed %d, EP Type %d, " ++ "Max Pkt %d, Multi Cnt %d\n", ++ hcchar.b.epdir, hcchar.b.lspddev, hcchar.b.eptype, ++ hcchar.b.mps, hcchar.b.multicnt); ++ ++ /* ++ * Program the HCSPLIT register for SPLITs ++ */ ++ hcsplt.d32 = 0; ++ if (hc->do_split) { ++ DWC_DEBUGPL(DBG_HCDV, "Programming HC %d with split --> %s\n", ++ hc->hc_num, ++ hc->complete_split ? "CSPLIT" : "SSPLIT"); ++ hcsplt.b.compsplt = hc->complete_split; ++ hcsplt.b.xactpos = hc->xact_pos; ++ hcsplt.b.hubaddr = hc->hub_addr; ++ hcsplt.b.prtaddr = hc->port_addr; ++ DWC_DEBUGPL(DBG_HCDV, "\t comp split %d\n", hc->complete_split); ++ DWC_DEBUGPL(DBG_HCDV, "\t xact pos %d\n", hc->xact_pos); ++ DWC_DEBUGPL(DBG_HCDV, "\t hub addr %d\n", hc->hub_addr); ++ DWC_DEBUGPL(DBG_HCDV, "\t port addr %d\n", hc->port_addr); ++ DWC_DEBUGPL(DBG_HCDV, "\t is_in %d\n", hc->ep_is_in); ++ DWC_DEBUGPL(DBG_HCDV, "\t Max Pkt: %d\n", hcchar.b.mps); ++ DWC_DEBUGPL(DBG_HCDV, "\t xferlen: %d\n", hc->xfer_len); ++ } ++ DWC_WRITE_REG32(&host_if->hc_regs[hc_num]->hcsplt, hcsplt.d32); ++ ++} ++ ++/** ++ * Attempts to halt a host channel. This function should only be called in ++ * Slave mode or to abort a transfer in either Slave mode or DMA mode. Under ++ * normal circumstances in DMA mode, the controller halts the channel when the ++ * transfer is complete or a condition occurs that requires application ++ * intervention. ++ * ++ * In slave mode, checks for a free request queue entry, then sets the Channel ++ * Enable and Channel Disable bits of the Host Channel Characteristics ++ * register of the specified channel to intiate the halt. If there is no free ++ * request queue entry, sets only the Channel Disable bit of the HCCHARn ++ * register to flush requests for this channel. In the latter case, sets a ++ * flag to indicate that the host channel needs to be halted when a request ++ * queue slot is open. ++ * ++ * In DMA mode, always sets the Channel Enable and Channel Disable bits of the ++ * HCCHARn register. The controller ensures there is space in the request ++ * queue before submitting the halt request. ++ * ++ * Some time may elapse before the core flushes any posted requests for this ++ * host channel and halts. The Channel Halted interrupt handler completes the ++ * deactivation of the host channel. ++ * ++ * @param core_if Controller register interface. ++ * @param hc Host channel to halt. ++ * @param halt_status Reason for halting the channel. ++ */ ++void dwc_otg_hc_halt(dwc_otg_core_if_t * core_if, ++ dwc_hc_t * hc, dwc_otg_halt_status_e halt_status) ++{ ++ gnptxsts_data_t nptxsts; ++ hptxsts_data_t hptxsts; ++ hcchar_data_t hcchar; ++ dwc_otg_hc_regs_t *hc_regs; ++ dwc_otg_core_global_regs_t *global_regs; ++ dwc_otg_host_global_regs_t *host_global_regs; ++ ++ hc_regs = core_if->host_if->hc_regs[hc->hc_num]; ++ global_regs = core_if->core_global_regs; ++ host_global_regs = core_if->host_if->host_global_regs; ++ ++ DWC_ASSERT(!(halt_status == DWC_OTG_HC_XFER_NO_HALT_STATUS), ++ "halt_status = %d\n", halt_status); ++ ++ if (halt_status == DWC_OTG_HC_XFER_URB_DEQUEUE || ++ halt_status == DWC_OTG_HC_XFER_AHB_ERR) { ++ /* ++ * Disable all channel interrupts except Ch Halted. The QTD ++ * and QH state associated with this transfer has been cleared ++ * (in the case of URB_DEQUEUE), so the channel needs to be ++ * shut down carefully to prevent crashes. ++ */ ++ hcintmsk_data_t hcintmsk; ++ hcintmsk.d32 = 0; ++ hcintmsk.b.chhltd = 1; ++ DWC_WRITE_REG32(&hc_regs->hcintmsk, hcintmsk.d32); ++ ++ /* ++ * Make sure no other interrupts besides halt are currently ++ * pending. Handling another interrupt could cause a crash due ++ * to the QTD and QH state. ++ */ ++ DWC_WRITE_REG32(&hc_regs->hcint, ~hcintmsk.d32); ++ ++ /* ++ * Make sure the halt status is set to URB_DEQUEUE or AHB_ERR ++ * even if the channel was already halted for some other ++ * reason. ++ */ ++ hc->halt_status = halt_status; ++ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ if (hcchar.b.chen == 0) { ++ /* ++ * The channel is either already halted or it hasn't ++ * started yet. In DMA mode, the transfer may halt if ++ * it finishes normally or a condition occurs that ++ * requires driver intervention. Don't want to halt ++ * the channel again. In either Slave or DMA mode, ++ * it's possible that the transfer has been assigned ++ * to a channel, but not started yet when an URB is ++ * dequeued. Don't want to halt a channel that hasn't ++ * started yet. ++ */ ++ return; ++ } ++ } ++ if (hc->halt_pending) { ++ /* ++ * A halt has already been issued for this channel. This might ++ * happen when a transfer is aborted by a higher level in ++ * the stack. ++ */ ++#ifdef DEBUG ++ DWC_PRINTF ++ ("*** %s: Channel %d, _hc->halt_pending already set ***\n", ++ __func__, hc->hc_num); ++ ++#endif ++ return; ++ } ++ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ ++ /* No need to set the bit in DDMA for disabling the channel */ ++ //TODO check it everywhere channel is disabled ++ if (!core_if->core_params->dma_desc_enable) ++ hcchar.b.chen = 1; ++ hcchar.b.chdis = 1; ++ ++ if (!core_if->dma_enable) { ++ /* Check for space in the request queue to issue the halt. */ ++ if (hc->ep_type == DWC_OTG_EP_TYPE_CONTROL || ++ hc->ep_type == DWC_OTG_EP_TYPE_BULK) { ++ nptxsts.d32 = DWC_READ_REG32(&global_regs->gnptxsts); ++ if (nptxsts.b.nptxqspcavail == 0) { ++ hcchar.b.chen = 0; ++ } ++ } else { ++ hptxsts.d32 = ++ DWC_READ_REG32(&host_global_regs->hptxsts); ++ if ((hptxsts.b.ptxqspcavail == 0) ++ || (core_if->queuing_high_bandwidth)) { ++ hcchar.b.chen = 0; ++ } ++ } ++ } ++ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32); ++ ++ hc->halt_status = halt_status; ++ ++ if (hcchar.b.chen) { ++ hc->halt_pending = 1; ++ hc->halt_on_queue = 0; ++ } else { ++ hc->halt_on_queue = 1; ++ } ++ ++ DWC_DEBUGPL(DBG_HCDV, "%s: Channel %d\n", __func__, hc->hc_num); ++ DWC_DEBUGPL(DBG_HCDV, " hcchar: 0x%08x\n", hcchar.d32); ++ DWC_DEBUGPL(DBG_HCDV, " halt_pending: %d\n", hc->halt_pending); ++ DWC_DEBUGPL(DBG_HCDV, " halt_on_queue: %d\n", hc->halt_on_queue); ++ DWC_DEBUGPL(DBG_HCDV, " halt_status: %d\n", hc->halt_status); ++ ++ return; ++} ++ ++/** ++ * Clears the transfer state for a host channel. This function is normally ++ * called after a transfer is done and the host channel is being released. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param hc Identifies the host channel to clean up. ++ */ ++void dwc_otg_hc_cleanup(dwc_otg_core_if_t * core_if, dwc_hc_t * hc) ++{ ++ dwc_otg_hc_regs_t *hc_regs; ++ ++ hc->xfer_started = 0; ++ ++ /* ++ * Clear channel interrupt enables and any unhandled channel interrupt ++ * conditions. ++ */ ++ hc_regs = core_if->host_if->hc_regs[hc->hc_num]; ++ DWC_WRITE_REG32(&hc_regs->hcintmsk, 0); ++ DWC_WRITE_REG32(&hc_regs->hcint, 0xFFFFFFFF); ++#ifdef DEBUG ++ DWC_TIMER_CANCEL(core_if->hc_xfer_timer[hc->hc_num]); ++#endif ++} ++ ++/** ++ * Sets the channel property that indicates in which frame a periodic transfer ++ * should occur. This is always set to the _next_ frame. This function has no ++ * effect on non-periodic transfers. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param hc Identifies the host channel to set up and its properties. ++ * @param hcchar Current value of the HCCHAR register for the specified host ++ * channel. ++ */ ++static inline void hc_set_even_odd_frame(dwc_otg_core_if_t * core_if, ++ dwc_hc_t * hc, hcchar_data_t * hcchar) ++{ ++ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR || ++ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) { ++ hfnum_data_t hfnum; ++ hfnum.d32 = ++ DWC_READ_REG32(&core_if->host_if->host_global_regs->hfnum); ++ ++ /* 1 if _next_ frame is odd, 0 if it's even */ ++ hcchar->b.oddfrm = (hfnum.b.frnum & 0x1) ? 0 : 1; ++#ifdef DEBUG ++ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR && hc->do_split ++ && !hc->complete_split) { ++ switch (hfnum.b.frnum & 0x7) { ++ case 7: ++ core_if->hfnum_7_samples++; ++ core_if->hfnum_7_frrem_accum += hfnum.b.frrem; ++ break; ++ case 0: ++ core_if->hfnum_0_samples++; ++ core_if->hfnum_0_frrem_accum += hfnum.b.frrem; ++ break; ++ default: ++ core_if->hfnum_other_samples++; ++ core_if->hfnum_other_frrem_accum += ++ hfnum.b.frrem; ++ break; ++ } ++ } ++#endif ++ } ++} ++ ++#ifdef DEBUG ++void hc_xfer_timeout(void *ptr) ++{ ++ hc_xfer_info_t *xfer_info = NULL; ++ int hc_num = 0; ++ ++ if (ptr) ++ xfer_info = (hc_xfer_info_t *) ptr; ++ ++ if (!xfer_info->hc) { ++ DWC_ERROR("xfer_info->hc = %p\n", xfer_info->hc); ++ return; ++ } ++ ++ hc_num = xfer_info->hc->hc_num; ++ DWC_WARN("%s: timeout on channel %d\n", __func__, hc_num); ++ DWC_WARN(" start_hcchar_val 0x%08x\n", ++ xfer_info->core_if->start_hcchar_val[hc_num]); ++} ++#endif ++ ++void ep_xfer_timeout(void *ptr) ++{ ++ ep_xfer_info_t *xfer_info = NULL; ++ int ep_num = 0; ++ dctl_data_t dctl = {.d32 = 0 }; ++ gintsts_data_t gintsts = {.d32 = 0 }; ++ gintmsk_data_t gintmsk = {.d32 = 0 }; ++ ++ if (ptr) ++ xfer_info = (ep_xfer_info_t *) ptr; ++ ++ if (!xfer_info->ep) { ++ DWC_ERROR("xfer_info->ep = %p\n", xfer_info->ep); ++ return; ++ } ++ ++ ep_num = xfer_info->ep->num; ++ DWC_WARN("%s: timeout on endpoit %d\n", __func__, ep_num); ++ /* Put the sate to 2 as it was time outed */ ++ xfer_info->state = 2; ++ ++ dctl.d32 = ++ DWC_READ_REG32(&xfer_info->core_if->dev_if->dev_global_regs->dctl); ++ gintsts.d32 = ++ DWC_READ_REG32(&xfer_info->core_if->core_global_regs->gintsts); ++ gintmsk.d32 = ++ DWC_READ_REG32(&xfer_info->core_if->core_global_regs->gintmsk); ++ ++ if (!gintmsk.b.goutnakeff) { ++ /* Unmask it */ ++ gintmsk.b.goutnakeff = 1; ++ DWC_WRITE_REG32(&xfer_info->core_if->core_global_regs->gintmsk, ++ gintmsk.d32); ++ ++ } ++ ++ if (!gintsts.b.goutnakeff) { ++ dctl.b.sgoutnak = 1; ++ } ++ DWC_WRITE_REG32(&xfer_info->core_if->dev_if->dev_global_regs->dctl, ++ dctl.d32); ++ ++} ++ ++void set_pid_isoc(dwc_hc_t * hc) ++{ ++ /* Set up the initial PID for the transfer. */ ++ if (hc->speed == DWC_OTG_EP_SPEED_HIGH) { ++ if (hc->ep_is_in) { ++ if (hc->multi_count == 1) { ++ hc->data_pid_start = DWC_OTG_HC_PID_DATA0; ++ } else if (hc->multi_count == 2) { ++ hc->data_pid_start = DWC_OTG_HC_PID_DATA1; ++ } else { ++ hc->data_pid_start = DWC_OTG_HC_PID_DATA2; ++ } ++ } else { ++ if (hc->multi_count == 1) { ++ hc->data_pid_start = DWC_OTG_HC_PID_DATA0; ++ } else { ++ hc->data_pid_start = DWC_OTG_HC_PID_MDATA; ++ } ++ } ++ } else { ++ hc->data_pid_start = DWC_OTG_HC_PID_DATA0; ++ } ++} ++ ++/** ++ * This function does the setup for a data transfer for a host channel and ++ * starts the transfer. May be called in either Slave mode or DMA mode. In ++ * Slave mode, the caller must ensure that there is sufficient space in the ++ * request queue and Tx Data FIFO. ++ * ++ * For an OUT transfer in Slave mode, it loads a data packet into the ++ * appropriate FIFO. If necessary, additional data packets will be loaded in ++ * the Host ISR. ++ * ++ * For an IN transfer in Slave mode, a data packet is requested. The data ++ * packets are unloaded from the Rx FIFO in the Host ISR. If necessary, ++ * additional data packets are requested in the Host ISR. ++ * ++ * For a PING transfer in Slave mode, the Do Ping bit is set in the HCTSIZ ++ * register along with a packet count of 1 and the channel is enabled. This ++ * causes a single PING transaction to occur. Other fields in HCTSIZ are ++ * simply set to 0 since no data transfer occurs in this case. ++ * ++ * For a PING transfer in DMA mode, the HCTSIZ register is initialized with ++ * all the information required to perform the subsequent data transfer. In ++ * addition, the Do Ping bit is set in the HCTSIZ register. In this case, the ++ * controller performs the entire PING protocol, then starts the data ++ * transfer. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param hc Information needed to initialize the host channel. The xfer_len ++ * value may be reduced to accommodate the max widths of the XferSize and ++ * PktCnt fields in the HCTSIZn register. The multi_count value may be changed ++ * to reflect the final xfer_len value. ++ */ ++void dwc_otg_hc_start_transfer(dwc_otg_core_if_t * core_if, dwc_hc_t * hc) ++{ ++ hcchar_data_t hcchar; ++ hctsiz_data_t hctsiz; ++ uint16_t num_packets; ++ uint32_t max_hc_xfer_size = core_if->core_params->max_transfer_size; ++ uint16_t max_hc_pkt_count = core_if->core_params->max_packet_count; ++ dwc_otg_hc_regs_t *hc_regs = core_if->host_if->hc_regs[hc->hc_num]; ++ ++ hctsiz.d32 = 0; ++ ++ if (hc->do_ping) { ++ if (!core_if->dma_enable) { ++ dwc_otg_hc_do_ping(core_if, hc); ++ hc->xfer_started = 1; ++ return; ++ } else { ++ hctsiz.b.dopng = 1; ++ } ++ } ++ ++ if (hc->do_split) { ++ num_packets = 1; ++ ++ if (hc->complete_split && !hc->ep_is_in) { ++ /* For CSPLIT OUT Transfer, set the size to 0 so the ++ * core doesn't expect any data written to the FIFO */ ++ hc->xfer_len = 0; ++ } else if (hc->ep_is_in || (hc->xfer_len > hc->max_packet)) { ++ hc->xfer_len = hc->max_packet; ++ } else if (!hc->ep_is_in && (hc->xfer_len > 188)) { ++ hc->xfer_len = 188; ++ } ++ ++ hctsiz.b.xfersize = hc->xfer_len; ++ } else { ++ /* ++ * Ensure that the transfer length and packet count will fit ++ * in the widths allocated for them in the HCTSIZn register. ++ */ ++ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR || ++ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) { ++ /* ++ * Make sure the transfer size is no larger than one ++ * (micro)frame's worth of data. (A check was done ++ * when the periodic transfer was accepted to ensure ++ * that a (micro)frame's worth of data can be ++ * programmed into a channel.) ++ */ ++ uint32_t max_periodic_len = ++ hc->multi_count * hc->max_packet; ++ if (hc->xfer_len > max_periodic_len) { ++ hc->xfer_len = max_periodic_len; ++ } else { ++ } ++ } else if (hc->xfer_len > max_hc_xfer_size) { ++ /* Make sure that xfer_len is a multiple of max packet size. */ ++ hc->xfer_len = max_hc_xfer_size - hc->max_packet + 1; ++ } ++ ++ if (hc->xfer_len > 0) { ++ num_packets = ++ (hc->xfer_len + hc->max_packet - ++ 1) / hc->max_packet; ++ if (num_packets > max_hc_pkt_count) { ++ num_packets = max_hc_pkt_count; ++ hc->xfer_len = num_packets * hc->max_packet; ++ } ++ } else { ++ /* Need 1 packet for transfer length of 0. */ ++ num_packets = 1; ++ } ++ ++ if (hc->ep_is_in) { ++ /* Always program an integral # of max packets for IN transfers. */ ++ hc->xfer_len = num_packets * hc->max_packet; ++ } ++ ++ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR || ++ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) { ++ /* ++ * Make sure that the multi_count field matches the ++ * actual transfer length. ++ */ ++ hc->multi_count = num_packets; ++ } ++ ++ if (hc->ep_type == DWC_OTG_EP_TYPE_ISOC) ++ set_pid_isoc(hc); ++ ++ hctsiz.b.xfersize = hc->xfer_len; ++ } ++ ++ hc->start_pkt_count = num_packets; ++ hctsiz.b.pktcnt = num_packets; ++ hctsiz.b.pid = hc->data_pid_start; ++ DWC_WRITE_REG32(&hc_regs->hctsiz, hctsiz.d32); ++ ++ DWC_DEBUGPL(DBG_HCDV, "%s: Channel %d\n", __func__, hc->hc_num); ++ DWC_DEBUGPL(DBG_HCDV, " Xfer Size: %d\n", hctsiz.b.xfersize); ++ DWC_DEBUGPL(DBG_HCDV, " Num Pkts: %d\n", hctsiz.b.pktcnt); ++ DWC_DEBUGPL(DBG_HCDV, " Start PID: %d\n", hctsiz.b.pid); ++ ++ if (core_if->dma_enable) { ++ dwc_dma_t dma_addr; ++ if (hc->align_buff) { ++ dma_addr = hc->align_buff; ++ } else { ++ dma_addr = ((unsigned long)hc->xfer_buff & 0xffffffff); ++ } ++ DWC_WRITE_REG32(&hc_regs->hcdma, dma_addr); ++ } ++ ++ /* Start the split */ ++ if (hc->do_split) { ++ hcsplt_data_t hcsplt; ++ hcsplt.d32 = DWC_READ_REG32(&hc_regs->hcsplt); ++ hcsplt.b.spltena = 1; ++ DWC_WRITE_REG32(&hc_regs->hcsplt, hcsplt.d32); ++ } ++ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ hcchar.b.multicnt = hc->multi_count; ++ hc_set_even_odd_frame(core_if, hc, &hcchar); ++#ifdef DEBUG ++ core_if->start_hcchar_val[hc->hc_num] = hcchar.d32; ++ if (hcchar.b.chdis) { ++ DWC_WARN("%s: chdis set, channel %d, hcchar 0x%08x\n", ++ __func__, hc->hc_num, hcchar.d32); ++ } ++#endif ++ ++ /* Set host channel enable after all other setup is complete. */ ++ hcchar.b.chen = 1; ++ hcchar.b.chdis = 0; ++ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32); ++ ++ hc->xfer_started = 1; ++ hc->requests++; ++ ++ if (!core_if->dma_enable && !hc->ep_is_in && hc->xfer_len > 0) { ++ /* Load OUT packet into the appropriate Tx FIFO. */ ++ dwc_otg_hc_write_packet(core_if, hc); ++ } ++#ifdef DEBUG ++ if (hc->ep_type != DWC_OTG_EP_TYPE_INTR) { ++ DWC_DEBUGPL(DBG_HCDV, "transfer %d from core_if %p\n", ++ hc->hc_num, core_if);//GRAYG ++ core_if->hc_xfer_info[hc->hc_num].core_if = core_if; ++ core_if->hc_xfer_info[hc->hc_num].hc = hc; ++ ++ /* Start a timer for this transfer. */ ++ DWC_TIMER_SCHEDULE(core_if->hc_xfer_timer[hc->hc_num], 10000); ++ } ++#endif ++} ++ ++/** ++ * This function does the setup for a data transfer for a host channel ++ * and starts the transfer in Descriptor DMA mode. ++ * ++ * Initializes HCTSIZ register. For a PING transfer the Do Ping bit is set. ++ * Sets PID and NTD values. For periodic transfers ++ * initializes SCHED_INFO field with micro-frame bitmap. ++ * ++ * Initializes HCDMA register with descriptor list address and CTD value ++ * then starts the transfer via enabling the channel. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param hc Information needed to initialize the host channel. ++ */ ++void dwc_otg_hc_start_transfer_ddma(dwc_otg_core_if_t * core_if, dwc_hc_t * hc) ++{ ++ dwc_otg_hc_regs_t *hc_regs = core_if->host_if->hc_regs[hc->hc_num]; ++ hcchar_data_t hcchar; ++ hctsiz_data_t hctsiz; ++ hcdma_data_t hcdma; ++ ++ hctsiz.d32 = 0; ++ ++ if (hc->do_ping) ++ hctsiz.b_ddma.dopng = 1; ++ ++ if (hc->ep_type == DWC_OTG_EP_TYPE_ISOC) ++ set_pid_isoc(hc); ++ ++ /* Packet Count and Xfer Size are not used in Descriptor DMA mode */ ++ hctsiz.b_ddma.pid = hc->data_pid_start; ++ hctsiz.b_ddma.ntd = hc->ntd - 1; /* 0 - 1 descriptor, 1 - 2 descriptors, etc. */ ++ hctsiz.b_ddma.schinfo = hc->schinfo; /* Non-zero only for high-speed interrupt endpoints */ ++ ++ DWC_DEBUGPL(DBG_HCDV, "%s: Channel %d\n", __func__, hc->hc_num); ++ DWC_DEBUGPL(DBG_HCDV, " Start PID: %d\n", hctsiz.b.pid); ++ DWC_DEBUGPL(DBG_HCDV, " NTD: %d\n", hctsiz.b_ddma.ntd); ++ ++ DWC_WRITE_REG32(&hc_regs->hctsiz, hctsiz.d32); ++ ++ hcdma.d32 = 0; ++ hcdma.b.dma_addr = ((uint32_t) hc->desc_list_addr) >> 11; ++ ++ /* Always start from first descriptor. */ ++ hcdma.b.ctd = 0; ++ DWC_WRITE_REG32(&hc_regs->hcdma, hcdma.d32); ++ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ hcchar.b.multicnt = hc->multi_count; ++ ++#ifdef DEBUG ++ core_if->start_hcchar_val[hc->hc_num] = hcchar.d32; ++ if (hcchar.b.chdis) { ++ DWC_WARN("%s: chdis set, channel %d, hcchar 0x%08x\n", ++ __func__, hc->hc_num, hcchar.d32); ++ } ++#endif ++ ++ /* Set host channel enable after all other setup is complete. */ ++ hcchar.b.chen = 1; ++ hcchar.b.chdis = 0; ++ ++ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32); ++ ++ hc->xfer_started = 1; ++ hc->requests++; ++ ++#ifdef DEBUG ++ if ((hc->ep_type != DWC_OTG_EP_TYPE_INTR) ++ && (hc->ep_type != DWC_OTG_EP_TYPE_ISOC)) { ++ DWC_DEBUGPL(DBG_HCDV, "DMA transfer %d from core_if %p\n", ++ hc->hc_num, core_if);//GRAYG ++ core_if->hc_xfer_info[hc->hc_num].core_if = core_if; ++ core_if->hc_xfer_info[hc->hc_num].hc = hc; ++ /* Start a timer for this transfer. */ ++ DWC_TIMER_SCHEDULE(core_if->hc_xfer_timer[hc->hc_num], 10000); ++ } ++#endif ++ ++} ++ ++/** ++ * This function continues a data transfer that was started by previous call ++ * to dwc_otg_hc_start_transfer. The caller must ensure there is ++ * sufficient space in the request queue and Tx Data FIFO. This function ++ * should only be called in Slave mode. In DMA mode, the controller acts ++ * autonomously to complete transfers programmed to a host channel. ++ * ++ * For an OUT transfer, a new data packet is loaded into the appropriate FIFO ++ * if there is any data remaining to be queued. For an IN transfer, another ++ * data packet is always requested. For the SETUP phase of a control transfer, ++ * this function does nothing. ++ * ++ * @return 1 if a new request is queued, 0 if no more requests are required ++ * for this transfer. ++ */ ++int dwc_otg_hc_continue_transfer(dwc_otg_core_if_t * core_if, dwc_hc_t * hc) ++{ ++ DWC_DEBUGPL(DBG_HCDV, "%s: Channel %d\n", __func__, hc->hc_num); ++ ++ if (hc->do_split) { ++ /* SPLITs always queue just once per channel */ ++ return 0; ++ } else if (hc->data_pid_start == DWC_OTG_HC_PID_SETUP) { ++ /* SETUPs are queued only once since they can't be NAKed. */ ++ return 0; ++ } else if (hc->ep_is_in) { ++ /* ++ * Always queue another request for other IN transfers. If ++ * back-to-back INs are issued and NAKs are received for both, ++ * the driver may still be processing the first NAK when the ++ * second NAK is received. When the interrupt handler clears ++ * the NAK interrupt for the first NAK, the second NAK will ++ * not be seen. So we can't depend on the NAK interrupt ++ * handler to requeue a NAKed request. Instead, IN requests ++ * are issued each time this function is called. When the ++ * transfer completes, the extra requests for the channel will ++ * be flushed. ++ */ ++ hcchar_data_t hcchar; ++ dwc_otg_hc_regs_t *hc_regs = ++ core_if->host_if->hc_regs[hc->hc_num]; ++ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ hc_set_even_odd_frame(core_if, hc, &hcchar); ++ hcchar.b.chen = 1; ++ hcchar.b.chdis = 0; ++ DWC_DEBUGPL(DBG_HCDV, " IN xfer: hcchar = 0x%08x\n", ++ hcchar.d32); ++ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32); ++ hc->requests++; ++ return 1; ++ } else { ++ /* OUT transfers. */ ++ if (hc->xfer_count < hc->xfer_len) { ++ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR || ++ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) { ++ hcchar_data_t hcchar; ++ dwc_otg_hc_regs_t *hc_regs; ++ hc_regs = core_if->host_if->hc_regs[hc->hc_num]; ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ hc_set_even_odd_frame(core_if, hc, &hcchar); ++ } ++ ++ /* Load OUT packet into the appropriate Tx FIFO. */ ++ dwc_otg_hc_write_packet(core_if, hc); ++ hc->requests++; ++ return 1; ++ } else { ++ return 0; ++ } ++ } ++} ++ ++/** ++ * Starts a PING transfer. This function should only be called in Slave mode. ++ * The Do Ping bit is set in the HCTSIZ register, then the channel is enabled. ++ */ ++void dwc_otg_hc_do_ping(dwc_otg_core_if_t * core_if, dwc_hc_t * hc) ++{ ++ hcchar_data_t hcchar; ++ hctsiz_data_t hctsiz; ++ dwc_otg_hc_regs_t *hc_regs = core_if->host_if->hc_regs[hc->hc_num]; ++ ++ DWC_DEBUGPL(DBG_HCDV, "%s: Channel %d\n", __func__, hc->hc_num); ++ ++ hctsiz.d32 = 0; ++ hctsiz.b.dopng = 1; ++ hctsiz.b.pktcnt = 1; ++ DWC_WRITE_REG32(&hc_regs->hctsiz, hctsiz.d32); ++ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ hcchar.b.chen = 1; ++ hcchar.b.chdis = 0; ++ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32); ++} ++ ++/* ++ * This function writes a packet into the Tx FIFO associated with the Host ++ * Channel. For a channel associated with a non-periodic EP, the non-periodic ++ * Tx FIFO is written. For a channel associated with a periodic EP, the ++ * periodic Tx FIFO is written. This function should only be called in Slave ++ * mode. ++ * ++ * Upon return the xfer_buff and xfer_count fields in _hc are incremented by ++ * then number of bytes written to the Tx FIFO. ++ */ ++void dwc_otg_hc_write_packet(dwc_otg_core_if_t * core_if, dwc_hc_t * hc) ++{ ++ uint32_t i; ++ uint32_t remaining_count; ++ uint32_t byte_count; ++ uint32_t dword_count; ++ ++ uint32_t *data_buff = (uint32_t *) (hc->xfer_buff); ++ uint32_t *data_fifo = core_if->data_fifo[hc->hc_num]; ++ ++ remaining_count = hc->xfer_len - hc->xfer_count; ++ if (remaining_count > hc->max_packet) { ++ byte_count = hc->max_packet; ++ } else { ++ byte_count = remaining_count; ++ } ++ ++ dword_count = (byte_count + 3) / 4; ++ ++ if ((((unsigned long)data_buff) & 0x3) == 0) { ++ /* xfer_buff is DWORD aligned. */ ++ for (i = 0; i < dword_count; i++, data_buff++) { ++ DWC_WRITE_REG32(data_fifo, *data_buff); ++ } ++ } else { ++ /* xfer_buff is not DWORD aligned. */ ++ for (i = 0; i < dword_count; i++, data_buff++) { ++ uint32_t data; ++ data = ++ (data_buff[0] | data_buff[1] << 8 | data_buff[2] << ++ 16 | data_buff[3] << 24); ++ DWC_WRITE_REG32(data_fifo, data); ++ } ++ } ++ ++ hc->xfer_count += byte_count; ++ hc->xfer_buff += byte_count; ++} ++ ++/** ++ * Gets the current USB frame number. This is the frame number from the last ++ * SOF packet. ++ */ ++uint32_t dwc_otg_get_frame_number(dwc_otg_core_if_t * core_if) ++{ ++ dsts_data_t dsts; ++ dsts.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts); ++ ++ /* read current frame/microframe number from DSTS register */ ++ return dsts.b.soffn; ++} ++ ++/** ++ * Calculates and gets the frame Interval value of HFIR register according PHY ++ * type and speed.The application can modify a value of HFIR register only after ++ * the Port Enable bit of the Host Port Control and Status register ++ * (HPRT.PrtEnaPort) has been set. ++*/ ++ ++uint32_t calc_frame_interval(dwc_otg_core_if_t * core_if) ++{ ++ gusbcfg_data_t usbcfg; ++ hwcfg2_data_t hwcfg2; ++ hprt0_data_t hprt0; ++ int clock = 60; // default value ++ usbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg); ++ hwcfg2.d32 = DWC_READ_REG32(&core_if->core_global_regs->ghwcfg2); ++ hprt0.d32 = DWC_READ_REG32(core_if->host_if->hprt0); ++ if (!usbcfg.b.physel && usbcfg.b.ulpi_utmi_sel && !usbcfg.b.phyif) ++ clock = 60; ++ if (usbcfg.b.physel && hwcfg2.b.fs_phy_type == 3) ++ clock = 48; ++ if (!usbcfg.b.phylpwrclksel && !usbcfg.b.physel && ++ !usbcfg.b.ulpi_utmi_sel && usbcfg.b.phyif) ++ clock = 30; ++ if (!usbcfg.b.phylpwrclksel && !usbcfg.b.physel && ++ !usbcfg.b.ulpi_utmi_sel && !usbcfg.b.phyif) ++ clock = 60; ++ if (usbcfg.b.phylpwrclksel && !usbcfg.b.physel && ++ !usbcfg.b.ulpi_utmi_sel && usbcfg.b.phyif) ++ clock = 48; ++ if (usbcfg.b.physel && !usbcfg.b.phyif && hwcfg2.b.fs_phy_type == 2) ++ clock = 48; ++ if (usbcfg.b.physel && hwcfg2.b.fs_phy_type == 1) ++ clock = 48; ++ if (hprt0.b.prtspd == 0) ++ /* High speed case */ ++ return 125 * clock - 1; ++ else ++ /* FS/LS case */ ++ return 1000 * clock - 1; ++} ++ ++/** ++ * This function reads a setup packet from the Rx FIFO into the destination ++ * buffer. This function is called from the Rx Status Queue Level (RxStsQLvl) ++ * Interrupt routine when a SETUP packet has been received in Slave mode. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param dest Destination buffer for packet data. ++ */ ++void dwc_otg_read_setup_packet(dwc_otg_core_if_t * core_if, uint32_t * dest) ++{ ++ device_grxsts_data_t status; ++ /* Get the 8 bytes of a setup transaction data */ ++ ++ /* Pop 2 DWORDS off the receive data FIFO into memory */ ++ dest[0] = DWC_READ_REG32(core_if->data_fifo[0]); ++ dest[1] = DWC_READ_REG32(core_if->data_fifo[0]); ++ if (core_if->snpsid >= OTG_CORE_REV_3_00a) { ++ status.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->grxstsp); ++ DWC_DEBUGPL(DBG_ANY, ++ "EP:%d BCnt:%d " "pktsts:%x Frame:%d(0x%0x)\n", ++ status.b.epnum, status.b.bcnt, status.b.pktsts, ++ status.b.fn, status.b.fn); ++ } ++} ++ ++/** ++ * This function enables EP0 OUT to receive SETUP packets and configures EP0 ++ * IN for transmitting packets. It is normally called when the ++ * "Enumeration Done" interrupt occurs. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP0 data. ++ */ ++void dwc_otg_ep0_activate(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ dsts_data_t dsts; ++ depctl_data_t diepctl; ++ depctl_data_t doepctl; ++ dctl_data_t dctl = {.d32 = 0 }; ++ ++ ep->stp_rollover = 0; ++ /* Read the Device Status and Endpoint 0 Control registers */ ++ dsts.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dsts); ++ diepctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[0]->diepctl); ++ doepctl.d32 = DWC_READ_REG32(&dev_if->out_ep_regs[0]->doepctl); ++ ++ /* Set the MPS of the IN EP based on the enumeration speed */ ++ switch (dsts.b.enumspd) { ++ case DWC_DSTS_ENUMSPD_HS_PHY_30MHZ_OR_60MHZ: ++ case DWC_DSTS_ENUMSPD_FS_PHY_30MHZ_OR_60MHZ: ++ case DWC_DSTS_ENUMSPD_FS_PHY_48MHZ: ++ diepctl.b.mps = DWC_DEP0CTL_MPS_64; ++ break; ++ case DWC_DSTS_ENUMSPD_LS_PHY_6MHZ: ++ diepctl.b.mps = DWC_DEP0CTL_MPS_8; ++ break; ++ } ++ ++ DWC_WRITE_REG32(&dev_if->in_ep_regs[0]->diepctl, diepctl.d32); ++ ++ /* Enable OUT EP for receive */ ++ if (core_if->snpsid <= OTG_CORE_REV_2_94a) { ++ doepctl.b.epena = 1; ++ DWC_WRITE_REG32(&dev_if->out_ep_regs[0]->doepctl, doepctl.d32); ++ } ++#ifdef VERBOSE ++ DWC_DEBUGPL(DBG_PCDV, "doepctl0=%0x\n", ++ DWC_READ_REG32(&dev_if->out_ep_regs[0]->doepctl)); ++ DWC_DEBUGPL(DBG_PCDV, "diepctl0=%0x\n", ++ DWC_READ_REG32(&dev_if->in_ep_regs[0]->diepctl)); ++#endif ++ dctl.b.cgnpinnak = 1; ++ ++ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dctl, dctl.d32, dctl.d32); ++ DWC_DEBUGPL(DBG_PCDV, "dctl=%0x\n", ++ DWC_READ_REG32(&dev_if->dev_global_regs->dctl)); ++ ++} ++ ++/** ++ * This function activates an EP. The Device EP control register for ++ * the EP is configured as defined in the ep structure. Note: This ++ * function is not used for EP0. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to activate. ++ */ ++void dwc_otg_ep_activate(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ depctl_data_t depctl; ++ volatile uint32_t *addr; ++ daint_data_t daintmsk = {.d32 = 0 }; ++ dcfg_data_t dcfg; ++ uint8_t i; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s() EP%d-%s\n", __func__, ep->num, ++ (ep->is_in ? "IN" : "OUT")); ++ ++#ifdef DWC_UTE_PER_IO ++ ep->xiso_frame_num = 0xFFFFFFFF; ++ ep->xiso_active_xfers = 0; ++ ep->xiso_queued_xfers = 0; ++#endif ++ /* Read DEPCTLn register */ ++ if (ep->is_in == 1) { ++ addr = &dev_if->in_ep_regs[ep->num]->diepctl; ++ daintmsk.ep.in = 1 << ep->num; ++ } else { ++ addr = &dev_if->out_ep_regs[ep->num]->doepctl; ++ daintmsk.ep.out = 1 << ep->num; ++ } ++ ++ /* If the EP is already active don't change the EP Control ++ * register. */ ++ depctl.d32 = DWC_READ_REG32(addr); ++ if (!depctl.b.usbactep) { ++ depctl.b.mps = ep->maxpacket; ++ depctl.b.eptype = ep->type; ++ depctl.b.txfnum = ep->tx_fifo_num; ++ ++ if (ep->type == DWC_OTG_EP_TYPE_ISOC) { ++ depctl.b.setd0pid = 1; // ??? ++ } else { ++ depctl.b.setd0pid = 1; ++ } ++ depctl.b.usbactep = 1; ++ ++ /* Update nextep_seq array and EPMSCNT in DCFG*/ ++ if (!(depctl.b.eptype & 1) && (ep->is_in == 1)) { // NP IN EP ++ for (i = 0; i <= core_if->dev_if->num_in_eps; i++) { ++ if (core_if->nextep_seq[i] == core_if->first_in_nextep_seq) ++ break; ++ } ++ core_if->nextep_seq[i] = ep->num; ++ core_if->nextep_seq[ep->num] = core_if->first_in_nextep_seq; ++ depctl.b.nextep = core_if->nextep_seq[ep->num]; ++ dcfg.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dcfg); ++ dcfg.b.epmscnt++; ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->dcfg, dcfg.d32); ++ ++ DWC_DEBUGPL(DBG_PCDV, ++ "%s first_in_nextep_seq= %2d; nextep_seq[]:\n", ++ __func__, core_if->first_in_nextep_seq); ++ for (i=0; i <= core_if->dev_if->num_in_eps; i++) { ++ DWC_DEBUGPL(DBG_PCDV, "%2d\n", ++ core_if->nextep_seq[i]); ++ } ++ ++ } ++ ++ ++ DWC_WRITE_REG32(addr, depctl.d32); ++ DWC_DEBUGPL(DBG_PCDV, "DEPCTL=%08x\n", DWC_READ_REG32(addr)); ++ } ++ ++ /* Enable the Interrupt for this EP */ ++ if (core_if->multiproc_int_enable) { ++ if (ep->is_in == 1) { ++ diepmsk_data_t diepmsk = {.d32 = 0 }; ++ diepmsk.b.xfercompl = 1; ++ diepmsk.b.timeout = 1; ++ diepmsk.b.epdisabled = 1; ++ diepmsk.b.ahberr = 1; ++ diepmsk.b.intknepmis = 1; ++ if (!core_if->en_multiple_tx_fifo && core_if->dma_enable) ++ diepmsk.b.intknepmis = 0; ++ diepmsk.b.txfifoundrn = 1; //????? ++ if (ep->type == DWC_OTG_EP_TYPE_ISOC) { ++ diepmsk.b.nak = 1; ++ } ++ ++ ++ ++/* ++ if (core_if->dma_desc_enable) { ++ diepmsk.b.bna = 1; ++ } ++*/ ++/* ++ if (core_if->dma_enable) { ++ doepmsk.b.nak = 1; ++ } ++*/ ++ DWC_WRITE_REG32(&dev_if->dev_global_regs-> ++ diepeachintmsk[ep->num], diepmsk.d32); ++ ++ } else { ++ doepmsk_data_t doepmsk = {.d32 = 0 }; ++ doepmsk.b.xfercompl = 1; ++ doepmsk.b.ahberr = 1; ++ doepmsk.b.epdisabled = 1; ++ if (ep->type == DWC_OTG_EP_TYPE_ISOC) ++ doepmsk.b.outtknepdis = 1; ++ ++/* ++ ++ if (core_if->dma_desc_enable) { ++ doepmsk.b.bna = 1; ++ } ++*/ ++/* ++ doepmsk.b.babble = 1; ++ doepmsk.b.nyet = 1; ++ doepmsk.b.nak = 1; ++*/ ++ DWC_WRITE_REG32(&dev_if->dev_global_regs-> ++ doepeachintmsk[ep->num], doepmsk.d32); ++ } ++ DWC_MODIFY_REG32(&dev_if->dev_global_regs->deachintmsk, ++ 0, daintmsk.d32); ++ } else { ++ if (ep->type == DWC_OTG_EP_TYPE_ISOC) { ++ if (ep->is_in) { ++ diepmsk_data_t diepmsk = {.d32 = 0 }; ++ diepmsk.b.nak = 1; ++ DWC_MODIFY_REG32(&dev_if->dev_global_regs->diepmsk, 0, diepmsk.d32); ++ } else { ++ doepmsk_data_t doepmsk = {.d32 = 0 }; ++ doepmsk.b.outtknepdis = 1; ++ DWC_MODIFY_REG32(&dev_if->dev_global_regs->doepmsk, 0, doepmsk.d32); ++ } ++ } ++ DWC_MODIFY_REG32(&dev_if->dev_global_regs->daintmsk, ++ 0, daintmsk.d32); ++ } ++ ++ DWC_DEBUGPL(DBG_PCDV, "DAINTMSK=%0x\n", ++ DWC_READ_REG32(&dev_if->dev_global_regs->daintmsk)); ++ ++ ep->stall_clear_flag = 0; ++ ++ return; ++} ++ ++/** ++ * This function deactivates an EP. This is done by clearing the USB Active ++ * EP bit in the Device EP control register. Note: This function is not used ++ * for EP0. EP0 cannot be deactivated. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to deactivate. ++ */ ++void dwc_otg_ep_deactivate(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ depctl_data_t depctl = {.d32 = 0 }; ++ volatile uint32_t *addr; ++ daint_data_t daintmsk = {.d32 = 0 }; ++ dcfg_data_t dcfg; ++ uint8_t i = 0; ++ ++#ifdef DWC_UTE_PER_IO ++ ep->xiso_frame_num = 0xFFFFFFFF; ++ ep->xiso_active_xfers = 0; ++ ep->xiso_queued_xfers = 0; ++#endif ++ ++ /* Read DEPCTLn register */ ++ if (ep->is_in == 1) { ++ addr = &core_if->dev_if->in_ep_regs[ep->num]->diepctl; ++ daintmsk.ep.in = 1 << ep->num; ++ } else { ++ addr = &core_if->dev_if->out_ep_regs[ep->num]->doepctl; ++ daintmsk.ep.out = 1 << ep->num; ++ } ++ ++ depctl.d32 = DWC_READ_REG32(addr); ++ ++ depctl.b.usbactep = 0; ++ ++ /* Update nextep_seq array and EPMSCNT in DCFG*/ ++ if (!(depctl.b.eptype & 1) && ep->is_in == 1) { // NP EP IN ++ for (i = 0; i <= core_if->dev_if->num_in_eps; i++) { ++ if (core_if->nextep_seq[i] == ep->num) ++ break; ++ } ++ core_if->nextep_seq[i] = core_if->nextep_seq[ep->num]; ++ if (core_if->first_in_nextep_seq == ep->num) ++ core_if->first_in_nextep_seq = i; ++ core_if->nextep_seq[ep->num] = 0xff; ++ depctl.b.nextep = 0; ++ dcfg.d32 = ++ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg); ++ dcfg.b.epmscnt--; ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg, ++ dcfg.d32); ++ ++ DWC_DEBUGPL(DBG_PCDV, ++ "%s first_in_nextep_seq= %2d; nextep_seq[]:\n", ++ __func__, core_if->first_in_nextep_seq); ++ for (i=0; i <= core_if->dev_if->num_in_eps; i++) { ++ DWC_DEBUGPL(DBG_PCDV, "%2d\n", core_if->nextep_seq[i]); ++ } ++ } ++ ++ if (ep->is_in == 1) ++ depctl.b.txfnum = 0; ++ ++ if (core_if->dma_desc_enable) ++ depctl.b.epdis = 1; ++ ++ DWC_WRITE_REG32(addr, depctl.d32); ++ depctl.d32 = DWC_READ_REG32(addr); ++ if (core_if->dma_enable && ep->type == DWC_OTG_EP_TYPE_ISOC ++ && depctl.b.epena) { ++ depctl_data_t depctl = {.d32 = 0}; ++ if (ep->is_in) { ++ diepint_data_t diepint = {.d32 = 0}; ++ ++ depctl.b.snak = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[ep->num]-> ++ diepctl, depctl.d32); ++ do { ++ dwc_udelay(10); ++ diepint.d32 = ++ DWC_READ_REG32(&core_if-> ++ dev_if->in_ep_regs[ep->num]-> ++ diepint); ++ } while (!diepint.b.inepnakeff); ++ diepint.b.inepnakeff = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[ep->num]-> ++ diepint, diepint.d32); ++ depctl.d32 = 0; ++ depctl.b.epdis = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[ep->num]-> ++ diepctl, depctl.d32); ++ do { ++ dwc_udelay(10); ++ diepint.d32 = ++ DWC_READ_REG32(&core_if-> ++ dev_if->in_ep_regs[ep->num]-> ++ diepint); ++ } while (!diepint.b.epdisabled); ++ diepint.b.epdisabled = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[ep->num]-> ++ diepint, diepint.d32); ++ } else { ++ dctl_data_t dctl = {.d32 = 0}; ++ gintmsk_data_t gintsts = {.d32 = 0}; ++ doepint_data_t doepint = {.d32 = 0}; ++ dctl.b.sgoutnak = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs-> ++ dctl, 0, dctl.d32); ++ do { ++ dwc_udelay(10); ++ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts); ++ } while (!gintsts.b.goutnakeff); ++ gintsts.d32 = 0; ++ gintsts.b.goutnakeff = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ ++ depctl.d32 = 0; ++ depctl.b.epdis = 1; ++ depctl.b.snak = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[ep->num]->doepctl, depctl.d32); ++ do ++ { ++ dwc_udelay(10); ++ doepint.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ out_ep_regs[ep->num]->doepint); ++ } while (!doepint.b.epdisabled); ++ ++ doepint.b.epdisabled = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[ep->num]->doepint, doepint.d32); ++ ++ dctl.d32 = 0; ++ dctl.b.cgoutnak = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0, dctl.d32); ++ } ++ } ++ ++ /* Disable the Interrupt for this EP */ ++ if (core_if->multiproc_int_enable) { ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->deachintmsk, ++ daintmsk.d32, 0); ++ ++ if (ep->is_in == 1) { ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs-> ++ diepeachintmsk[ep->num], 0); ++ } else { ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs-> ++ doepeachintmsk[ep->num], 0); ++ } ++ } else { ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->daintmsk, ++ daintmsk.d32, 0); ++ } ++ ++} ++ ++/** ++ * This function initializes dma descriptor chain. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to start the transfer on. ++ */ ++static void init_dma_desc_chain(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ dwc_otg_dev_dma_desc_t *dma_desc; ++ uint32_t offset; ++ uint32_t xfer_est; ++ int i; ++ unsigned maxxfer_local, total_len; ++ ++ if (!ep->is_in && ep->type == DWC_OTG_EP_TYPE_INTR && ++ (ep->maxpacket%4)) { ++ maxxfer_local = ep->maxpacket; ++ total_len = ep->xfer_len; ++ } else { ++ maxxfer_local = ep->maxxfer; ++ total_len = ep->total_len; ++ } ++ ++ ep->desc_cnt = (total_len / maxxfer_local) + ++ ((total_len % maxxfer_local) ? 1 : 0); ++ ++ if (!ep->desc_cnt) ++ ep->desc_cnt = 1; ++ ++ if (ep->desc_cnt > MAX_DMA_DESC_CNT) ++ ep->desc_cnt = MAX_DMA_DESC_CNT; ++ ++ dma_desc = ep->desc_addr; ++ if (maxxfer_local == ep->maxpacket) { ++ if ((total_len % maxxfer_local) && ++ (total_len/maxxfer_local < MAX_DMA_DESC_CNT)) { ++ xfer_est = (ep->desc_cnt - 1) * maxxfer_local + ++ (total_len % maxxfer_local); ++ } else ++ xfer_est = ep->desc_cnt * maxxfer_local; ++ } else ++ xfer_est = total_len; ++ offset = 0; ++ for (i = 0; i < ep->desc_cnt; ++i) { ++ /** DMA Descriptor Setup */ ++ if (xfer_est > maxxfer_local) { ++ dma_desc->status.b.bs = BS_HOST_BUSY; ++ dma_desc->status.b.l = 0; ++ dma_desc->status.b.ioc = 0; ++ dma_desc->status.b.sp = 0; ++ dma_desc->status.b.bytes = maxxfer_local; ++ dma_desc->buf = ep->dma_addr + offset; ++ dma_desc->status.b.sts = 0; ++ dma_desc->status.b.bs = BS_HOST_READY; ++ ++ xfer_est -= maxxfer_local; ++ offset += maxxfer_local; ++ } else { ++ dma_desc->status.b.bs = BS_HOST_BUSY; ++ dma_desc->status.b.l = 1; ++ dma_desc->status.b.ioc = 1; ++ if (ep->is_in) { ++ dma_desc->status.b.sp = ++ (xfer_est % ++ ep->maxpacket) ? 1 : ((ep-> ++ sent_zlp) ? 1 : 0); ++ dma_desc->status.b.bytes = xfer_est; ++ } else { ++ if (maxxfer_local == ep->maxpacket) ++ dma_desc->status.b.bytes = xfer_est; ++ else ++ dma_desc->status.b.bytes = ++ xfer_est + ((4 - (xfer_est & 0x3)) & 0x3); ++ } ++ ++ dma_desc->buf = ep->dma_addr + offset; ++ dma_desc->status.b.sts = 0; ++ dma_desc->status.b.bs = BS_HOST_READY; ++ } ++ dma_desc++; ++ } ++} ++/** ++ * This function is called when to write ISOC data into appropriate dedicated ++ * periodic FIFO. ++ */ ++static int32_t write_isoc_tx_fifo(dwc_otg_core_if_t * core_if, dwc_ep_t * dwc_ep) ++{ ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ dwc_otg_dev_in_ep_regs_t *ep_regs; ++ dtxfsts_data_t txstatus = {.d32 = 0 }; ++ uint32_t len = 0; ++ int epnum = dwc_ep->num; ++ int dwords; ++ ++ DWC_DEBUGPL(DBG_PCD, "Dedicated TxFifo Empty: %d \n", epnum); ++ ++ ep_regs = core_if->dev_if->in_ep_regs[epnum]; ++ ++ len = dwc_ep->xfer_len - dwc_ep->xfer_count; ++ ++ if (len > dwc_ep->maxpacket) { ++ len = dwc_ep->maxpacket; ++ } ++ ++ dwords = (len + 3) / 4; ++ ++ /* While there is space in the queue and space in the FIFO and ++ * More data to tranfer, Write packets to the Tx FIFO */ ++ txstatus.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dtxfsts); ++ DWC_DEBUGPL(DBG_PCDV, "b4 dtxfsts[%d]=0x%08x\n", epnum, txstatus.d32); ++ ++ while (txstatus.b.txfspcavail > dwords && ++ dwc_ep->xfer_count < dwc_ep->xfer_len && dwc_ep->xfer_len != 0) { ++ /* Write the FIFO */ ++ dwc_otg_ep_write_packet(core_if, dwc_ep, 0); ++ ++ len = dwc_ep->xfer_len - dwc_ep->xfer_count; ++ if (len > dwc_ep->maxpacket) { ++ len = dwc_ep->maxpacket; ++ } ++ ++ dwords = (len + 3) / 4; ++ txstatus.d32 = ++ DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dtxfsts); ++ DWC_DEBUGPL(DBG_PCDV, "dtxfsts[%d]=0x%08x\n", epnum, ++ txstatus.d32); ++ } ++ ++ DWC_DEBUGPL(DBG_PCDV, "b4 dtxfsts[%d]=0x%08x\n", epnum, ++ DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dtxfsts)); ++ ++ return 1; ++} ++/** ++ * This function does the setup for a data transfer for an EP and ++ * starts the transfer. For an IN transfer, the packets will be ++ * loaded into the appropriate Tx FIFO in the ISR. For OUT transfers, ++ * the packets are unloaded from the Rx FIFO in the ISR. the ISR. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to start the transfer on. ++ */ ++ ++void dwc_otg_ep_start_transfer(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ depctl_data_t depctl; ++ deptsiz_data_t deptsiz; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ DWC_DEBUGPL((DBG_PCDV | DBG_CILV), "%s()\n", __func__); ++ DWC_DEBUGPL(DBG_PCD, "ep%d-%s xfer_len=%d xfer_cnt=%d " ++ "xfer_buff=%p start_xfer_buff=%p, total_len = %d\n", ++ ep->num, (ep->is_in ? "IN" : "OUT"), ep->xfer_len, ++ ep->xfer_count, ep->xfer_buff, ep->start_xfer_buff, ++ ep->total_len); ++ /* IN endpoint */ ++ if (ep->is_in == 1) { ++ dwc_otg_dev_in_ep_regs_t *in_regs = ++ core_if->dev_if->in_ep_regs[ep->num]; ++ ++ gnptxsts_data_t gtxstatus; ++ ++ gtxstatus.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->gnptxsts); ++ ++ if (core_if->en_multiple_tx_fifo == 0 ++ && gtxstatus.b.nptxqspcavail == 0 && !core_if->dma_enable) { ++#ifdef DEBUG ++ DWC_PRINTF("TX Queue Full (0x%0x)\n", gtxstatus.d32); ++#endif ++ return; ++ } ++ ++ depctl.d32 = DWC_READ_REG32(&(in_regs->diepctl)); ++ deptsiz.d32 = DWC_READ_REG32(&(in_regs->dieptsiz)); ++ ++ if (ep->maxpacket > ep->maxxfer / MAX_PKT_CNT) ++ ep->xfer_len += (ep->maxxfer < (ep->total_len - ep->xfer_len)) ? ++ ep->maxxfer : (ep->total_len - ep->xfer_len); ++ else ++ ep->xfer_len += (MAX_PKT_CNT * ep->maxpacket < (ep->total_len - ep->xfer_len)) ? ++ MAX_PKT_CNT * ep->maxpacket : (ep->total_len - ep->xfer_len); ++ ++ ++ /* Zero Length Packet? */ ++ if ((ep->xfer_len - ep->xfer_count) == 0) { ++ deptsiz.b.xfersize = 0; ++ deptsiz.b.pktcnt = 1; ++ } else { ++ /* Program the transfer size and packet count ++ * as follows: xfersize = N * maxpacket + ++ * short_packet pktcnt = N + (short_packet ++ * exist ? 1 : 0) ++ */ ++ deptsiz.b.xfersize = ep->xfer_len - ep->xfer_count; ++ deptsiz.b.pktcnt = ++ (ep->xfer_len - ep->xfer_count - 1 + ++ ep->maxpacket) / ep->maxpacket; ++ if (deptsiz.b.pktcnt > MAX_PKT_CNT) { ++ deptsiz.b.pktcnt = MAX_PKT_CNT; ++ deptsiz.b.xfersize = deptsiz.b.pktcnt * ep->maxpacket; ++ } ++ if (ep->type == DWC_OTG_EP_TYPE_ISOC) ++ deptsiz.b.mc = deptsiz.b.pktcnt; ++ } ++ ++ /* Write the DMA register */ ++ if (core_if->dma_enable) { ++ if (core_if->dma_desc_enable == 0) { ++ if (ep->type != DWC_OTG_EP_TYPE_ISOC) ++ deptsiz.b.mc = 1; ++ DWC_WRITE_REG32(&in_regs->dieptsiz, ++ deptsiz.d32); ++ DWC_WRITE_REG32(&(in_regs->diepdma), ++ (uint32_t) ep->dma_addr); ++ } else { ++#ifdef DWC_UTE_CFI ++ /* The descriptor chain should be already initialized by now */ ++ if (ep->buff_mode != BM_STANDARD) { ++ DWC_WRITE_REG32(&in_regs->diepdma, ++ ep->descs_dma_addr); ++ } else { ++#endif ++ init_dma_desc_chain(core_if, ep); ++ /** DIEPDMAn Register write */ ++ DWC_WRITE_REG32(&in_regs->diepdma, ++ ep->dma_desc_addr); ++#ifdef DWC_UTE_CFI ++ } ++#endif ++ } ++ } else { ++ DWC_WRITE_REG32(&in_regs->dieptsiz, deptsiz.d32); ++ if (ep->type != DWC_OTG_EP_TYPE_ISOC) { ++ /** ++ * Enable the Non-Periodic Tx FIFO empty interrupt, ++ * or the Tx FIFO epmty interrupt in dedicated Tx FIFO mode, ++ * the data will be written into the fifo by the ISR. ++ */ ++ if (core_if->en_multiple_tx_fifo == 0) { ++ intr_mask.b.nptxfempty = 1; ++ DWC_MODIFY_REG32 ++ (&core_if->core_global_regs->gintmsk, ++ intr_mask.d32, intr_mask.d32); ++ } else { ++ /* Enable the Tx FIFO Empty Interrupt for this EP */ ++ if (ep->xfer_len > 0) { ++ uint32_t fifoemptymsk = 0; ++ fifoemptymsk = 1 << ep->num; ++ DWC_MODIFY_REG32 ++ (&core_if->dev_if->dev_global_regs->dtknqr4_fifoemptymsk, ++ 0, fifoemptymsk); ++ ++ } ++ } ++ } else { ++ write_isoc_tx_fifo(core_if, ep); ++ } ++ } ++ if (!core_if->core_params->en_multiple_tx_fifo && core_if->dma_enable) ++ depctl.b.nextep = core_if->nextep_seq[ep->num]; ++ ++ if (ep->type == DWC_OTG_EP_TYPE_ISOC) { ++ dsts_data_t dsts = {.d32 = 0}; ++ if (ep->bInterval == 1) { ++ dsts.d32 = ++ DWC_READ_REG32(&core_if->dev_if-> ++ dev_global_regs->dsts); ++ ep->frame_num = dsts.b.soffn + ep->bInterval; ++ if (ep->frame_num > 0x3FFF) { ++ ep->frm_overrun = 1; ++ ep->frame_num &= 0x3FFF; ++ } else ++ ep->frm_overrun = 0; ++ if (ep->frame_num & 0x1) { ++ depctl.b.setd1pid = 1; ++ } else { ++ depctl.b.setd0pid = 1; ++ } ++ } ++ } ++ /* EP enable, IN data in FIFO */ ++ depctl.b.cnak = 1; ++ depctl.b.epena = 1; ++ DWC_WRITE_REG32(&in_regs->diepctl, depctl.d32); ++ ++ } else { ++ /* OUT endpoint */ ++ dwc_otg_dev_out_ep_regs_t *out_regs = ++ core_if->dev_if->out_ep_regs[ep->num]; ++ ++ depctl.d32 = DWC_READ_REG32(&(out_regs->doepctl)); ++ deptsiz.d32 = DWC_READ_REG32(&(out_regs->doeptsiz)); ++ ++ if (!core_if->dma_desc_enable) { ++ if (ep->maxpacket > ep->maxxfer / MAX_PKT_CNT) ++ ep->xfer_len += (ep->maxxfer < (ep->total_len - ep->xfer_len)) ? ++ ep->maxxfer : (ep->total_len - ep->xfer_len); ++ else ++ ep->xfer_len += (MAX_PKT_CNT * ep->maxpacket < (ep->total_len ++ - ep->xfer_len)) ? MAX_PKT_CNT * ep->maxpacket : (ep->total_len - ep->xfer_len); ++ } ++ ++ /* Program the transfer size and packet count as follows: ++ * ++ * pktcnt = N ++ * xfersize = N * maxpacket ++ */ ++ if ((ep->xfer_len - ep->xfer_count) == 0) { ++ /* Zero Length Packet */ ++ deptsiz.b.xfersize = ep->maxpacket; ++ deptsiz.b.pktcnt = 1; ++ } else { ++ deptsiz.b.pktcnt = ++ (ep->xfer_len - ep->xfer_count + ++ (ep->maxpacket - 1)) / ep->maxpacket; ++ if (deptsiz.b.pktcnt > MAX_PKT_CNT) { ++ deptsiz.b.pktcnt = MAX_PKT_CNT; ++ } ++ if (!core_if->dma_desc_enable) { ++ ep->xfer_len = ++ deptsiz.b.pktcnt * ep->maxpacket + ep->xfer_count; ++ } ++ deptsiz.b.xfersize = ep->xfer_len - ep->xfer_count; ++ } ++ ++ DWC_DEBUGPL(DBG_PCDV, "ep%d xfersize=%d pktcnt=%d\n", ++ ep->num, deptsiz.b.xfersize, deptsiz.b.pktcnt); ++ ++ if (core_if->dma_enable) { ++ if (!core_if->dma_desc_enable) { ++ DWC_WRITE_REG32(&out_regs->doeptsiz, ++ deptsiz.d32); ++ ++ DWC_WRITE_REG32(&(out_regs->doepdma), ++ (uint32_t) ep->dma_addr); ++ } else { ++#ifdef DWC_UTE_CFI ++ /* The descriptor chain should be already initialized by now */ ++ if (ep->buff_mode != BM_STANDARD) { ++ DWC_WRITE_REG32(&out_regs->doepdma, ++ ep->descs_dma_addr); ++ } else { ++#endif ++ /** This is used for interrupt out transfers*/ ++ if (!ep->xfer_len) ++ ep->xfer_len = ep->total_len; ++ init_dma_desc_chain(core_if, ep); ++ ++ if (core_if->core_params->dev_out_nak) { ++ if (ep->type == DWC_OTG_EP_TYPE_BULK) { ++ deptsiz.b.pktcnt = (ep->total_len + ++ (ep->maxpacket - 1)) / ep->maxpacket; ++ deptsiz.b.xfersize = ep->total_len; ++ /* Remember initial value of doeptsiz */ ++ core_if->start_doeptsiz_val[ep->num] = deptsiz.d32; ++ DWC_WRITE_REG32(&out_regs->doeptsiz, ++ deptsiz.d32); ++ } ++ } ++ /** DOEPDMAn Register write */ ++ DWC_WRITE_REG32(&out_regs->doepdma, ++ ep->dma_desc_addr); ++#ifdef DWC_UTE_CFI ++ } ++#endif ++ } ++ } else { ++ DWC_WRITE_REG32(&out_regs->doeptsiz, deptsiz.d32); ++ } ++ ++ if (ep->type == DWC_OTG_EP_TYPE_ISOC) { ++ dsts_data_t dsts = {.d32 = 0}; ++ if (ep->bInterval == 1) { ++ dsts.d32 = ++ DWC_READ_REG32(&core_if->dev_if-> ++ dev_global_regs->dsts); ++ ep->frame_num = dsts.b.soffn + ep->bInterval; ++ if (ep->frame_num > 0x3FFF) { ++ ep->frm_overrun = 1; ++ ep->frame_num &= 0x3FFF; ++ } else ++ ep->frm_overrun = 0; ++ ++ if (ep->frame_num & 0x1) { ++ depctl.b.setd1pid = 1; ++ } else { ++ depctl.b.setd0pid = 1; ++ } ++ } ++ } ++ ++ /* EP enable */ ++ depctl.b.cnak = 1; ++ depctl.b.epena = 1; ++ ++ DWC_WRITE_REG32(&out_regs->doepctl, depctl.d32); ++ ++ DWC_DEBUGPL(DBG_PCD, "DOEPCTL=%08x DOEPTSIZ=%08x\n", ++ DWC_READ_REG32(&out_regs->doepctl), ++ DWC_READ_REG32(&out_regs->doeptsiz)); ++ DWC_DEBUGPL(DBG_PCD, "DAINTMSK=%08x GINTMSK=%08x\n", ++ DWC_READ_REG32(&core_if->dev_if->dev_global_regs-> ++ daintmsk), ++ DWC_READ_REG32(&core_if->core_global_regs-> ++ gintmsk)); ++ ++ /* Timer is scheduling only for out bulk transfers for ++ * "Device DDMA OUT NAK Enhancement" feature to inform user ++ * about received data payload in case of timeout ++ */ ++ if (core_if->core_params->dev_out_nak) { ++ if (ep->type == DWC_OTG_EP_TYPE_BULK) { ++ core_if->ep_xfer_info[ep->num].core_if = core_if; ++ core_if->ep_xfer_info[ep->num].ep = ep; ++ core_if->ep_xfer_info[ep->num].state = 1; ++ ++ /* Start a timer for this transfer. */ ++ DWC_TIMER_SCHEDULE(core_if->ep_xfer_timer[ep->num], 10000); ++ } ++ } ++ } ++} ++ ++/** ++ * This function setup a zero length transfer in Buffer DMA and ++ * Slave modes for usb requests with zero field set ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to start the transfer on. ++ * ++ */ ++void dwc_otg_ep_start_zl_transfer(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ ++ depctl_data_t depctl; ++ deptsiz_data_t deptsiz; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ DWC_DEBUGPL((DBG_PCDV | DBG_CILV), "%s()\n", __func__); ++ DWC_PRINTF("zero length transfer is called\n"); ++ ++ /* IN endpoint */ ++ if (ep->is_in == 1) { ++ dwc_otg_dev_in_ep_regs_t *in_regs = ++ core_if->dev_if->in_ep_regs[ep->num]; ++ ++ depctl.d32 = DWC_READ_REG32(&(in_regs->diepctl)); ++ deptsiz.d32 = DWC_READ_REG32(&(in_regs->dieptsiz)); ++ ++ deptsiz.b.xfersize = 0; ++ deptsiz.b.pktcnt = 1; ++ ++ /* Write the DMA register */ ++ if (core_if->dma_enable) { ++ if (core_if->dma_desc_enable == 0) { ++ deptsiz.b.mc = 1; ++ DWC_WRITE_REG32(&in_regs->dieptsiz, ++ deptsiz.d32); ++ DWC_WRITE_REG32(&(in_regs->diepdma), ++ (uint32_t) ep->dma_addr); ++ } ++ } else { ++ DWC_WRITE_REG32(&in_regs->dieptsiz, deptsiz.d32); ++ /** ++ * Enable the Non-Periodic Tx FIFO empty interrupt, ++ * or the Tx FIFO epmty interrupt in dedicated Tx FIFO mode, ++ * the data will be written into the fifo by the ISR. ++ */ ++ if (core_if->en_multiple_tx_fifo == 0) { ++ intr_mask.b.nptxfempty = 1; ++ DWC_MODIFY_REG32(&core_if-> ++ core_global_regs->gintmsk, ++ intr_mask.d32, intr_mask.d32); ++ } else { ++ /* Enable the Tx FIFO Empty Interrupt for this EP */ ++ if (ep->xfer_len > 0) { ++ uint32_t fifoemptymsk = 0; ++ fifoemptymsk = 1 << ep->num; ++ DWC_MODIFY_REG32(&core_if-> ++ dev_if->dev_global_regs->dtknqr4_fifoemptymsk, ++ 0, fifoemptymsk); ++ } ++ } ++ } ++ ++ if (!core_if->core_params->en_multiple_tx_fifo && core_if->dma_enable) ++ depctl.b.nextep = core_if->nextep_seq[ep->num]; ++ /* EP enable, IN data in FIFO */ ++ depctl.b.cnak = 1; ++ depctl.b.epena = 1; ++ DWC_WRITE_REG32(&in_regs->diepctl, depctl.d32); ++ ++ } else { ++ /* OUT endpoint */ ++ dwc_otg_dev_out_ep_regs_t *out_regs = ++ core_if->dev_if->out_ep_regs[ep->num]; ++ ++ depctl.d32 = DWC_READ_REG32(&(out_regs->doepctl)); ++ deptsiz.d32 = DWC_READ_REG32(&(out_regs->doeptsiz)); ++ ++ /* Zero Length Packet */ ++ deptsiz.b.xfersize = ep->maxpacket; ++ deptsiz.b.pktcnt = 1; ++ ++ if (core_if->dma_enable) { ++ if (!core_if->dma_desc_enable) { ++ DWC_WRITE_REG32(&out_regs->doeptsiz, ++ deptsiz.d32); ++ ++ DWC_WRITE_REG32(&(out_regs->doepdma), ++ (uint32_t) ep->dma_addr); ++ } ++ } else { ++ DWC_WRITE_REG32(&out_regs->doeptsiz, deptsiz.d32); ++ } ++ ++ /* EP enable */ ++ depctl.b.cnak = 1; ++ depctl.b.epena = 1; ++ ++ DWC_WRITE_REG32(&out_regs->doepctl, depctl.d32); ++ ++ } ++} ++ ++/** ++ * This function does the setup for a data transfer for EP0 and starts ++ * the transfer. For an IN transfer, the packets will be loaded into ++ * the appropriate Tx FIFO in the ISR. For OUT transfers, the packets are ++ * unloaded from the Rx FIFO in the ISR. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP0 data. ++ */ ++void dwc_otg_ep0_start_transfer(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ depctl_data_t depctl; ++ deptsiz0_data_t deptsiz; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ dwc_otg_dev_dma_desc_t *dma_desc; ++ ++ DWC_DEBUGPL(DBG_PCD, "ep%d-%s xfer_len=%d xfer_cnt=%d " ++ "xfer_buff=%p start_xfer_buff=%p \n", ++ ep->num, (ep->is_in ? "IN" : "OUT"), ep->xfer_len, ++ ep->xfer_count, ep->xfer_buff, ep->start_xfer_buff); ++ ++ ep->total_len = ep->xfer_len; ++ ++ /* IN endpoint */ ++ if (ep->is_in == 1) { ++ dwc_otg_dev_in_ep_regs_t *in_regs = ++ core_if->dev_if->in_ep_regs[0]; ++ ++ gnptxsts_data_t gtxstatus; ++ ++ if (core_if->snpsid >= OTG_CORE_REV_3_00a) { ++ depctl.d32 = DWC_READ_REG32(&in_regs->diepctl); ++ if (depctl.b.epena) ++ return; ++ } ++ ++ gtxstatus.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->gnptxsts); ++ ++ /* If dedicated FIFO every time flush fifo before enable ep*/ ++ if (core_if->en_multiple_tx_fifo && core_if->snpsid >= OTG_CORE_REV_3_00a) ++ dwc_otg_flush_tx_fifo(core_if, ep->tx_fifo_num); ++ ++ if (core_if->en_multiple_tx_fifo == 0 ++ && gtxstatus.b.nptxqspcavail == 0 ++ && !core_if->dma_enable) { ++#ifdef DEBUG ++ deptsiz.d32 = DWC_READ_REG32(&in_regs->dieptsiz); ++ DWC_DEBUGPL(DBG_PCD, "DIEPCTL0=%0x\n", ++ DWC_READ_REG32(&in_regs->diepctl)); ++ DWC_DEBUGPL(DBG_PCD, "DIEPTSIZ0=%0x (sz=%d, pcnt=%d)\n", ++ deptsiz.d32, ++ deptsiz.b.xfersize, deptsiz.b.pktcnt); ++ DWC_PRINTF("TX Queue or FIFO Full (0x%0x)\n", ++ gtxstatus.d32); ++#endif ++ return; ++ } ++ ++ depctl.d32 = DWC_READ_REG32(&in_regs->diepctl); ++ deptsiz.d32 = DWC_READ_REG32(&in_regs->dieptsiz); ++ ++ /* Zero Length Packet? */ ++ if (ep->xfer_len == 0) { ++ deptsiz.b.xfersize = 0; ++ deptsiz.b.pktcnt = 1; ++ } else { ++ /* Program the transfer size and packet count ++ * as follows: xfersize = N * maxpacket + ++ * short_packet pktcnt = N + (short_packet ++ * exist ? 1 : 0) ++ */ ++ if (ep->xfer_len > ep->maxpacket) { ++ ep->xfer_len = ep->maxpacket; ++ deptsiz.b.xfersize = ep->maxpacket; ++ } else { ++ deptsiz.b.xfersize = ep->xfer_len; ++ } ++ deptsiz.b.pktcnt = 1; ++ ++ } ++ DWC_DEBUGPL(DBG_PCDV, ++ "IN len=%d xfersize=%d pktcnt=%d [%08x]\n", ++ ep->xfer_len, deptsiz.b.xfersize, deptsiz.b.pktcnt, ++ deptsiz.d32); ++ ++ /* Write the DMA register */ ++ if (core_if->dma_enable) { ++ if (core_if->dma_desc_enable == 0) { ++ DWC_WRITE_REG32(&in_regs->dieptsiz, ++ deptsiz.d32); ++ ++ DWC_WRITE_REG32(&(in_regs->diepdma), ++ (uint32_t) ep->dma_addr); ++ } else { ++ dma_desc = core_if->dev_if->in_desc_addr; ++ ++ /** DMA Descriptor Setup */ ++ dma_desc->status.b.bs = BS_HOST_BUSY; ++ dma_desc->status.b.l = 1; ++ dma_desc->status.b.ioc = 1; ++ dma_desc->status.b.sp = ++ (ep->xfer_len == ep->maxpacket) ? 0 : 1; ++ dma_desc->status.b.bytes = ep->xfer_len; ++ dma_desc->buf = ep->dma_addr; ++ dma_desc->status.b.sts = 0; ++ dma_desc->status.b.bs = BS_HOST_READY; ++ ++ /** DIEPDMA0 Register write */ ++ DWC_WRITE_REG32(&in_regs->diepdma, ++ core_if-> ++ dev_if->dma_in_desc_addr); ++ } ++ } else { ++ DWC_WRITE_REG32(&in_regs->dieptsiz, deptsiz.d32); ++ } ++ ++ if (!core_if->core_params->en_multiple_tx_fifo && core_if->dma_enable) ++ depctl.b.nextep = core_if->nextep_seq[ep->num]; ++ /* EP enable, IN data in FIFO */ ++ depctl.b.cnak = 1; ++ depctl.b.epena = 1; ++ DWC_WRITE_REG32(&in_regs->diepctl, depctl.d32); ++ ++ /** ++ * Enable the Non-Periodic Tx FIFO empty interrupt, the ++ * data will be written into the fifo by the ISR. ++ */ ++ if (!core_if->dma_enable) { ++ if (core_if->en_multiple_tx_fifo == 0) { ++ intr_mask.b.nptxfempty = 1; ++ DWC_MODIFY_REG32(&core_if-> ++ core_global_regs->gintmsk, ++ intr_mask.d32, intr_mask.d32); ++ } else { ++ /* Enable the Tx FIFO Empty Interrupt for this EP */ ++ if (ep->xfer_len > 0) { ++ uint32_t fifoemptymsk = 0; ++ fifoemptymsk |= 1 << ep->num; ++ DWC_MODIFY_REG32(&core_if-> ++ dev_if->dev_global_regs->dtknqr4_fifoemptymsk, ++ 0, fifoemptymsk); ++ } ++ } ++ } ++ } else { ++ /* OUT endpoint */ ++ dwc_otg_dev_out_ep_regs_t *out_regs = ++ core_if->dev_if->out_ep_regs[0]; ++ ++ depctl.d32 = DWC_READ_REG32(&out_regs->doepctl); ++ deptsiz.d32 = DWC_READ_REG32(&out_regs->doeptsiz); ++ ++ /* Program the transfer size and packet count as follows: ++ * xfersize = N * (maxpacket + 4 - (maxpacket % 4)) ++ * pktcnt = N */ ++ /* Zero Length Packet */ ++ deptsiz.b.xfersize = ep->maxpacket; ++ deptsiz.b.pktcnt = 1; ++ if (core_if->snpsid >= OTG_CORE_REV_3_00a) ++ deptsiz.b.supcnt = 3; ++ ++ DWC_DEBUGPL(DBG_PCDV, "len=%d xfersize=%d pktcnt=%d\n", ++ ep->xfer_len, deptsiz.b.xfersize, deptsiz.b.pktcnt); ++ ++ if (core_if->dma_enable) { ++ if (!core_if->dma_desc_enable) { ++ DWC_WRITE_REG32(&out_regs->doeptsiz, ++ deptsiz.d32); ++ ++ DWC_WRITE_REG32(&(out_regs->doepdma), ++ (uint32_t) ep->dma_addr); ++ } else { ++ dma_desc = core_if->dev_if->out_desc_addr; ++ ++ /** DMA Descriptor Setup */ ++ dma_desc->status.b.bs = BS_HOST_BUSY; ++ if (core_if->snpsid >= OTG_CORE_REV_3_00a) { ++ dma_desc->status.b.mtrf = 0; ++ dma_desc->status.b.sr = 0; ++ } ++ dma_desc->status.b.l = 1; ++ dma_desc->status.b.ioc = 1; ++ dma_desc->status.b.bytes = ep->maxpacket; ++ dma_desc->buf = ep->dma_addr; ++ dma_desc->status.b.sts = 0; ++ dma_desc->status.b.bs = BS_HOST_READY; ++ ++ /** DOEPDMA0 Register write */ ++ DWC_WRITE_REG32(&out_regs->doepdma, ++ core_if->dev_if-> ++ dma_out_desc_addr); ++ } ++ } else { ++ DWC_WRITE_REG32(&out_regs->doeptsiz, deptsiz.d32); ++ } ++ ++ /* EP enable */ ++ depctl.b.cnak = 1; ++ depctl.b.epena = 1; ++ DWC_WRITE_REG32(&(out_regs->doepctl), depctl.d32); ++ } ++} ++ ++/** ++ * This function continues control IN transfers started by ++ * dwc_otg_ep0_start_transfer, when the transfer does not fit in a ++ * single packet. NOTE: The DIEPCTL0/DOEPCTL0 registers only have one ++ * bit for the packet count. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP0 data. ++ */ ++void dwc_otg_ep0_continue_transfer(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ depctl_data_t depctl; ++ deptsiz0_data_t deptsiz; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ dwc_otg_dev_dma_desc_t *dma_desc; ++ ++ if (ep->is_in == 1) { ++ dwc_otg_dev_in_ep_regs_t *in_regs = ++ core_if->dev_if->in_ep_regs[0]; ++ gnptxsts_data_t tx_status = {.d32 = 0 }; ++ ++ tx_status.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->gnptxsts); ++ /** @todo Should there be check for room in the Tx ++ * Status Queue. If not remove the code above this comment. */ ++ ++ depctl.d32 = DWC_READ_REG32(&in_regs->diepctl); ++ deptsiz.d32 = DWC_READ_REG32(&in_regs->dieptsiz); ++ ++ /* Program the transfer size and packet count ++ * as follows: xfersize = N * maxpacket + ++ * short_packet pktcnt = N + (short_packet ++ * exist ? 1 : 0) ++ */ ++ ++ if (core_if->dma_desc_enable == 0) { ++ deptsiz.b.xfersize = ++ (ep->total_len - ep->xfer_count) > ++ ep->maxpacket ? ep->maxpacket : (ep->total_len - ++ ep->xfer_count); ++ deptsiz.b.pktcnt = 1; ++ if (core_if->dma_enable == 0) { ++ ep->xfer_len += deptsiz.b.xfersize; ++ } else { ++ ep->xfer_len = deptsiz.b.xfersize; ++ } ++ DWC_WRITE_REG32(&in_regs->dieptsiz, deptsiz.d32); ++ } else { ++ ep->xfer_len = ++ (ep->total_len - ep->xfer_count) > ++ ep->maxpacket ? ep->maxpacket : (ep->total_len - ++ ep->xfer_count); ++ ++ dma_desc = core_if->dev_if->in_desc_addr; ++ ++ /** DMA Descriptor Setup */ ++ dma_desc->status.b.bs = BS_HOST_BUSY; ++ dma_desc->status.b.l = 1; ++ dma_desc->status.b.ioc = 1; ++ dma_desc->status.b.sp = ++ (ep->xfer_len == ep->maxpacket) ? 0 : 1; ++ dma_desc->status.b.bytes = ep->xfer_len; ++ dma_desc->buf = ep->dma_addr; ++ dma_desc->status.b.sts = 0; ++ dma_desc->status.b.bs = BS_HOST_READY; ++ ++ /** DIEPDMA0 Register write */ ++ DWC_WRITE_REG32(&in_regs->diepdma, ++ core_if->dev_if->dma_in_desc_addr); ++ } ++ ++ DWC_DEBUGPL(DBG_PCDV, ++ "IN len=%d xfersize=%d pktcnt=%d [%08x]\n", ++ ep->xfer_len, deptsiz.b.xfersize, deptsiz.b.pktcnt, ++ deptsiz.d32); ++ ++ /* Write the DMA register */ ++ if (core_if->hwcfg2.b.architecture == DWC_INT_DMA_ARCH) { ++ if (core_if->dma_desc_enable == 0) ++ DWC_WRITE_REG32(&(in_regs->diepdma), ++ (uint32_t) ep->dma_addr); ++ } ++ if (!core_if->core_params->en_multiple_tx_fifo && core_if->dma_enable) ++ depctl.b.nextep = core_if->nextep_seq[ep->num]; ++ /* EP enable, IN data in FIFO */ ++ depctl.b.cnak = 1; ++ depctl.b.epena = 1; ++ DWC_WRITE_REG32(&in_regs->diepctl, depctl.d32); ++ ++ /** ++ * Enable the Non-Periodic Tx FIFO empty interrupt, the ++ * data will be written into the fifo by the ISR. ++ */ ++ if (!core_if->dma_enable) { ++ if (core_if->en_multiple_tx_fifo == 0) { ++ /* First clear it from GINTSTS */ ++ intr_mask.b.nptxfempty = 1; ++ DWC_MODIFY_REG32(&core_if-> ++ core_global_regs->gintmsk, ++ intr_mask.d32, intr_mask.d32); ++ ++ } else { ++ /* Enable the Tx FIFO Empty Interrupt for this EP */ ++ if (ep->xfer_len > 0) { ++ uint32_t fifoemptymsk = 0; ++ fifoemptymsk |= 1 << ep->num; ++ DWC_MODIFY_REG32(&core_if-> ++ dev_if->dev_global_regs->dtknqr4_fifoemptymsk, ++ 0, fifoemptymsk); ++ } ++ } ++ } ++ } else { ++ dwc_otg_dev_out_ep_regs_t *out_regs = ++ core_if->dev_if->out_ep_regs[0]; ++ ++ depctl.d32 = DWC_READ_REG32(&out_regs->doepctl); ++ deptsiz.d32 = DWC_READ_REG32(&out_regs->doeptsiz); ++ ++ /* Program the transfer size and packet count ++ * as follows: xfersize = N * maxpacket + ++ * short_packet pktcnt = N + (short_packet ++ * exist ? 1 : 0) ++ */ ++ deptsiz.b.xfersize = ep->maxpacket; ++ deptsiz.b.pktcnt = 1; ++ ++ if (core_if->dma_desc_enable == 0) { ++ DWC_WRITE_REG32(&out_regs->doeptsiz, deptsiz.d32); ++ } else { ++ dma_desc = core_if->dev_if->out_desc_addr; ++ ++ /** DMA Descriptor Setup */ ++ dma_desc->status.b.bs = BS_HOST_BUSY; ++ dma_desc->status.b.l = 1; ++ dma_desc->status.b.ioc = 1; ++ dma_desc->status.b.bytes = ep->maxpacket; ++ dma_desc->buf = ep->dma_addr; ++ dma_desc->status.b.sts = 0; ++ dma_desc->status.b.bs = BS_HOST_READY; ++ ++ /** DOEPDMA0 Register write */ ++ DWC_WRITE_REG32(&out_regs->doepdma, ++ core_if->dev_if->dma_out_desc_addr); ++ } ++ ++ DWC_DEBUGPL(DBG_PCDV, ++ "IN len=%d xfersize=%d pktcnt=%d [%08x]\n", ++ ep->xfer_len, deptsiz.b.xfersize, deptsiz.b.pktcnt, ++ deptsiz.d32); ++ ++ /* Write the DMA register */ ++ if (core_if->hwcfg2.b.architecture == DWC_INT_DMA_ARCH) { ++ if (core_if->dma_desc_enable == 0) ++ DWC_WRITE_REG32(&(out_regs->doepdma), ++ (uint32_t) ep->dma_addr); ++ ++ } ++ ++ /* EP enable, IN data in FIFO */ ++ depctl.b.cnak = 1; ++ depctl.b.epena = 1; ++ DWC_WRITE_REG32(&out_regs->doepctl, depctl.d32); ++ ++ } ++} ++ ++#ifdef DEBUG ++void dump_msg(const u8 * buf, unsigned int length) ++{ ++ unsigned int start, num, i; ++ char line[52], *p; ++ ++ if (length >= 512) ++ return; ++ start = 0; ++ while (length > 0) { ++ num = length < 16u ? length : 16u; ++ p = line; ++ for (i = 0; i < num; ++i) { ++ if (i == 8) ++ *p++ = ' '; ++ DWC_SPRINTF(p, " %02x", buf[i]); ++ p += 3; ++ } ++ *p = 0; ++ DWC_PRINTF("%6x: %s\n", start, line); ++ buf += num; ++ start += num; ++ length -= num; ++ } ++} ++#else ++static inline void dump_msg(const u8 * buf, unsigned int length) ++{ ++} ++#endif ++ ++/** ++ * This function writes a packet into the Tx FIFO associated with the ++ * EP. For non-periodic EPs the non-periodic Tx FIFO is written. For ++ * periodic EPs the periodic Tx FIFO associated with the EP is written ++ * with all packets for the next micro-frame. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to write packet for. ++ * @param dma Indicates if DMA is being used. ++ */ ++void dwc_otg_ep_write_packet(dwc_otg_core_if_t * core_if, dwc_ep_t * ep, ++ int dma) ++{ ++ /** ++ * The buffer is padded to DWORD on a per packet basis in ++ * slave/dma mode if the MPS is not DWORD aligned. The last ++ * packet, if short, is also padded to a multiple of DWORD. ++ * ++ * ep->xfer_buff always starts DWORD aligned in memory and is a ++ * multiple of DWORD in length ++ * ++ * ep->xfer_len can be any number of bytes ++ * ++ * ep->xfer_count is a multiple of ep->maxpacket until the last ++ * packet ++ * ++ * FIFO access is DWORD */ ++ ++ uint32_t i; ++ uint32_t byte_count; ++ uint32_t dword_count; ++ uint32_t *fifo; ++ uint32_t *data_buff = (uint32_t *) ep->xfer_buff; ++ ++ DWC_DEBUGPL((DBG_PCDV | DBG_CILV), "%s(%p,%p)\n", __func__, core_if, ++ ep); ++ if (ep->xfer_count >= ep->xfer_len) { ++ DWC_WARN("%s() No data for EP%d!!!\n", __func__, ep->num); ++ return; ++ } ++ ++ /* Find the byte length of the packet either short packet or MPS */ ++ if ((ep->xfer_len - ep->xfer_count) < ep->maxpacket) { ++ byte_count = ep->xfer_len - ep->xfer_count; ++ } else { ++ byte_count = ep->maxpacket; ++ } ++ ++ /* Find the DWORD length, padded by extra bytes as neccessary if MPS ++ * is not a multiple of DWORD */ ++ dword_count = (byte_count + 3) / 4; ++ ++#ifdef VERBOSE ++ dump_msg(ep->xfer_buff, byte_count); ++#endif ++ ++ /**@todo NGS Where are the Periodic Tx FIFO addresses ++ * intialized? What should this be? */ ++ ++ fifo = core_if->data_fifo[ep->num]; ++ ++ DWC_DEBUGPL((DBG_PCDV | DBG_CILV), "fifo=%p buff=%p *p=%08x bc=%d\n", ++ fifo, data_buff, *data_buff, byte_count); ++ ++ if (!dma) { ++ for (i = 0; i < dword_count; i++, data_buff++) { ++ DWC_WRITE_REG32(fifo, *data_buff); ++ } ++ } ++ ++ ep->xfer_count += byte_count; ++ ep->xfer_buff += byte_count; ++ ep->dma_addr += byte_count; ++} ++ ++/** ++ * Set the EP STALL. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to set the stall on. ++ */ ++void dwc_otg_ep_set_stall(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ depctl_data_t depctl; ++ volatile uint32_t *depctl_addr; ++ ++ DWC_DEBUGPL(DBG_PCD, "%s ep%d-%s\n", __func__, ep->num, ++ (ep->is_in ? "IN" : "OUT")); ++ ++ if (ep->is_in == 1) { ++ depctl_addr = &(core_if->dev_if->in_ep_regs[ep->num]->diepctl); ++ depctl.d32 = DWC_READ_REG32(depctl_addr); ++ ++ /* set the disable and stall bits */ ++ if (depctl.b.epena) { ++ depctl.b.epdis = 1; ++ } ++ depctl.b.stall = 1; ++ DWC_WRITE_REG32(depctl_addr, depctl.d32); ++ } else { ++ depctl_addr = &(core_if->dev_if->out_ep_regs[ep->num]->doepctl); ++ depctl.d32 = DWC_READ_REG32(depctl_addr); ++ ++ /* set the stall bit */ ++ depctl.b.stall = 1; ++ DWC_WRITE_REG32(depctl_addr, depctl.d32); ++ } ++ ++ DWC_DEBUGPL(DBG_PCD, "DEPCTL=%0x\n", DWC_READ_REG32(depctl_addr)); ++ ++ return; ++} ++ ++/** ++ * Clear the EP STALL. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to clear stall from. ++ */ ++void dwc_otg_ep_clear_stall(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ depctl_data_t depctl; ++ volatile uint32_t *depctl_addr; ++ ++ DWC_DEBUGPL(DBG_PCD, "%s ep%d-%s\n", __func__, ep->num, ++ (ep->is_in ? "IN" : "OUT")); ++ ++ if (ep->is_in == 1) { ++ depctl_addr = &(core_if->dev_if->in_ep_regs[ep->num]->diepctl); ++ } else { ++ depctl_addr = &(core_if->dev_if->out_ep_regs[ep->num]->doepctl); ++ } ++ ++ depctl.d32 = DWC_READ_REG32(depctl_addr); ++ ++ /* clear the stall bits */ ++ depctl.b.stall = 0; ++ ++ /* ++ * USB Spec 9.4.5: For endpoints using data toggle, regardless ++ * of whether an endpoint has the Halt feature set, a ++ * ClearFeature(ENDPOINT_HALT) request always results in the ++ * data toggle being reinitialized to DATA0. ++ */ ++ if (ep->type == DWC_OTG_EP_TYPE_INTR || ++ ep->type == DWC_OTG_EP_TYPE_BULK) { ++ depctl.b.setd0pid = 1; /* DATA0 */ ++ } ++ ++ DWC_WRITE_REG32(depctl_addr, depctl.d32); ++ DWC_DEBUGPL(DBG_PCD, "DEPCTL=%0x\n", DWC_READ_REG32(depctl_addr)); ++ return; ++} ++ ++/** ++ * This function reads a packet from the Rx FIFO into the destination ++ * buffer. To read SETUP data use dwc_otg_read_setup_packet. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param dest Destination buffer for the packet. ++ * @param bytes Number of bytes to copy to the destination. ++ */ ++void dwc_otg_read_packet(dwc_otg_core_if_t * core_if, ++ uint8_t * dest, uint16_t bytes) ++{ ++ int i; ++ int word_count = (bytes + 3) / 4; ++ ++ volatile uint32_t *fifo = core_if->data_fifo[0]; ++ uint32_t *data_buff = (uint32_t *) dest; ++ ++ /** ++ * @todo Account for the case where _dest is not dword aligned. This ++ * requires reading data from the FIFO into a uint32_t temp buffer, ++ * then moving it into the data buffer. ++ */ ++ ++ DWC_DEBUGPL((DBG_PCDV | DBG_CILV), "%s(%p,%p,%d)\n", __func__, ++ core_if, dest, bytes); ++ ++ for (i = 0; i < word_count; i++, data_buff++) { ++ *data_buff = DWC_READ_REG32(fifo); ++ } ++ ++ return; ++} ++ ++/** ++ * This functions reads the device registers and prints them ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++void dwc_otg_dump_dev_registers(dwc_otg_core_if_t * core_if) ++{ ++ int i; ++ volatile uint32_t *addr; ++ ++ DWC_PRINTF("Device Global Registers\n"); ++ addr = &core_if->dev_if->dev_global_regs->dcfg; ++ DWC_PRINTF("DCFG @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->dev_global_regs->dctl; ++ DWC_PRINTF("DCTL @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->dev_global_regs->dsts; ++ DWC_PRINTF("DSTS @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->dev_global_regs->diepmsk; ++ DWC_PRINTF("DIEPMSK @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->dev_global_regs->doepmsk; ++ DWC_PRINTF("DOEPMSK @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->dev_global_regs->daint; ++ DWC_PRINTF("DAINT @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->dev_global_regs->daintmsk; ++ DWC_PRINTF("DAINTMSK @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->dev_global_regs->dtknqr1; ++ DWC_PRINTF("DTKNQR1 @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ if (core_if->hwcfg2.b.dev_token_q_depth > 6) { ++ addr = &core_if->dev_if->dev_global_regs->dtknqr2; ++ DWC_PRINTF("DTKNQR2 @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ } ++ ++ addr = &core_if->dev_if->dev_global_regs->dvbusdis; ++ DWC_PRINTF("DVBUSID @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ ++ addr = &core_if->dev_if->dev_global_regs->dvbuspulse; ++ DWC_PRINTF("DVBUSPULSE @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ ++ addr = &core_if->dev_if->dev_global_regs->dtknqr3_dthrctl; ++ DWC_PRINTF("DTKNQR3_DTHRCTL @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ ++ if (core_if->hwcfg2.b.dev_token_q_depth > 22) { ++ addr = &core_if->dev_if->dev_global_regs->dtknqr4_fifoemptymsk; ++ DWC_PRINTF("DTKNQR4 @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ } ++ ++ addr = &core_if->dev_if->dev_global_regs->dtknqr4_fifoemptymsk; ++ DWC_PRINTF("FIFOEMPMSK @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ ++ if (core_if->hwcfg2.b.multi_proc_int) { ++ ++ addr = &core_if->dev_if->dev_global_regs->deachint; ++ DWC_PRINTF("DEACHINT @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->dev_global_regs->deachintmsk; ++ DWC_PRINTF("DEACHINTMSK @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ ++ for (i = 0; i <= core_if->dev_if->num_in_eps; i++) { ++ addr = ++ &core_if->dev_if-> ++ dev_global_regs->diepeachintmsk[i]; ++ DWC_PRINTF("DIEPEACHINTMSK[%d] @0x%08lX : 0x%08X\n", ++ i, (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ } ++ ++ for (i = 0; i <= core_if->dev_if->num_out_eps; i++) { ++ addr = ++ &core_if->dev_if-> ++ dev_global_regs->doepeachintmsk[i]; ++ DWC_PRINTF("DOEPEACHINTMSK[%d] @0x%08lX : 0x%08X\n", ++ i, (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ } ++ } ++ ++ for (i = 0; i <= core_if->dev_if->num_in_eps; i++) { ++ DWC_PRINTF("Device IN EP %d Registers\n", i); ++ addr = &core_if->dev_if->in_ep_regs[i]->diepctl; ++ DWC_PRINTF("DIEPCTL @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->in_ep_regs[i]->diepint; ++ DWC_PRINTF("DIEPINT @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->in_ep_regs[i]->dieptsiz; ++ DWC_PRINTF("DIETSIZ @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->in_ep_regs[i]->diepdma; ++ DWC_PRINTF("DIEPDMA @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->in_ep_regs[i]->dtxfsts; ++ DWC_PRINTF("DTXFSTS @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->in_ep_regs[i]->diepdmab; ++ DWC_PRINTF("DIEPDMAB @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, 0 /*DWC_READ_REG32(addr) */ ); ++ } ++ ++ for (i = 0; i <= core_if->dev_if->num_out_eps; i++) { ++ DWC_PRINTF("Device OUT EP %d Registers\n", i); ++ addr = &core_if->dev_if->out_ep_regs[i]->doepctl; ++ DWC_PRINTF("DOEPCTL @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->out_ep_regs[i]->doepint; ++ DWC_PRINTF("DOEPINT @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->out_ep_regs[i]->doeptsiz; ++ DWC_PRINTF("DOETSIZ @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->dev_if->out_ep_regs[i]->doepdma; ++ DWC_PRINTF("DOEPDMA @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ if (core_if->dma_enable) { /* Don't access this register in SLAVE mode */ ++ addr = &core_if->dev_if->out_ep_regs[i]->doepdmab; ++ DWC_PRINTF("DOEPDMAB @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ } ++ ++ } ++} ++ ++/** ++ * This functions reads the SPRAM and prints its content ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++void dwc_otg_dump_spram(dwc_otg_core_if_t * core_if) ++{ ++ volatile uint8_t *addr, *start_addr, *end_addr; ++ ++ DWC_PRINTF("SPRAM Data:\n"); ++ start_addr = (void *)core_if->core_global_regs; ++ DWC_PRINTF("Base Address: 0x%8lX\n", (unsigned long)start_addr); ++ start_addr += 0x00028000; ++ end_addr = (void *)core_if->core_global_regs; ++ end_addr += 0x000280e0; ++ ++ for (addr = start_addr; addr < end_addr; addr += 16) { ++ DWC_PRINTF ++ ("0x%8lX:\t%2X %2X %2X %2X %2X %2X %2X %2X %2X %2X %2X %2X %2X %2X %2X %2X\n", ++ (unsigned long)addr, addr[0], addr[1], addr[2], addr[3], ++ addr[4], addr[5], addr[6], addr[7], addr[8], addr[9], ++ addr[10], addr[11], addr[12], addr[13], addr[14], addr[15] ++ ); ++ } ++ ++ return; ++} ++ ++/** ++ * This function reads the host registers and prints them ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++void dwc_otg_dump_host_registers(dwc_otg_core_if_t * core_if) ++{ ++ int i; ++ volatile uint32_t *addr; ++ ++ DWC_PRINTF("Host Global Registers\n"); ++ addr = &core_if->host_if->host_global_regs->hcfg; ++ DWC_PRINTF("HCFG @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->host_if->host_global_regs->hfir; ++ DWC_PRINTF("HFIR @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->host_if->host_global_regs->hfnum; ++ DWC_PRINTF("HFNUM @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->host_if->host_global_regs->hptxsts; ++ DWC_PRINTF("HPTXSTS @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->host_if->host_global_regs->haint; ++ DWC_PRINTF("HAINT @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->host_if->host_global_regs->haintmsk; ++ DWC_PRINTF("HAINTMSK @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ if (core_if->dma_desc_enable) { ++ addr = &core_if->host_if->host_global_regs->hflbaddr; ++ DWC_PRINTF("HFLBADDR @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ } ++ ++ addr = core_if->host_if->hprt0; ++ DWC_PRINTF("HPRT0 @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ ++ for (i = 0; i < core_if->core_params->host_channels; i++) { ++ DWC_PRINTF("Host Channel %d Specific Registers\n", i); ++ addr = &core_if->host_if->hc_regs[i]->hcchar; ++ DWC_PRINTF("HCCHAR @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->host_if->hc_regs[i]->hcsplt; ++ DWC_PRINTF("HCSPLT @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->host_if->hc_regs[i]->hcint; ++ DWC_PRINTF("HCINT @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->host_if->hc_regs[i]->hcintmsk; ++ DWC_PRINTF("HCINTMSK @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->host_if->hc_regs[i]->hctsiz; ++ DWC_PRINTF("HCTSIZ @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->host_if->hc_regs[i]->hcdma; ++ DWC_PRINTF("HCDMA @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ if (core_if->dma_desc_enable) { ++ addr = &core_if->host_if->hc_regs[i]->hcdmab; ++ DWC_PRINTF("HCDMAB @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ } ++ ++ } ++ return; ++} ++ ++/** ++ * This function reads the core global registers and prints them ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++void dwc_otg_dump_global_registers(dwc_otg_core_if_t * core_if) ++{ ++ int i, ep_num; ++ volatile uint32_t *addr; ++ char *txfsiz; ++ ++ DWC_PRINTF("Core Global Registers\n"); ++ addr = &core_if->core_global_regs->gotgctl; ++ DWC_PRINTF("GOTGCTL @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->gotgint; ++ DWC_PRINTF("GOTGINT @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->gahbcfg; ++ DWC_PRINTF("GAHBCFG @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->gusbcfg; ++ DWC_PRINTF("GUSBCFG @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->grstctl; ++ DWC_PRINTF("GRSTCTL @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->gintsts; ++ DWC_PRINTF("GINTSTS @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->gintmsk; ++ DWC_PRINTF("GINTMSK @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->grxstsr; ++ DWC_PRINTF("GRXSTSR @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->grxfsiz; ++ DWC_PRINTF("GRXFSIZ @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->gnptxfsiz; ++ DWC_PRINTF("GNPTXFSIZ @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->gnptxsts; ++ DWC_PRINTF("GNPTXSTS @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->gi2cctl; ++ DWC_PRINTF("GI2CCTL @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->gpvndctl; ++ DWC_PRINTF("GPVNDCTL @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->ggpio; ++ DWC_PRINTF("GGPIO @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->guid; ++ DWC_PRINTF("GUID @0x%08lX : 0x%08X\n", ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->gsnpsid; ++ DWC_PRINTF("GSNPSID @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->ghwcfg1; ++ DWC_PRINTF("GHWCFG1 @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->ghwcfg2; ++ DWC_PRINTF("GHWCFG2 @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->ghwcfg3; ++ DWC_PRINTF("GHWCFG3 @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->ghwcfg4; ++ DWC_PRINTF("GHWCFG4 @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->glpmcfg; ++ DWC_PRINTF("GLPMCFG @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->gpwrdn; ++ DWC_PRINTF("GPWRDN @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->gdfifocfg; ++ DWC_PRINTF("GDFIFOCFG @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ addr = &core_if->core_global_regs->adpctl; ++ DWC_PRINTF("ADPCTL @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ dwc_otg_adp_read_reg(core_if)); ++ addr = &core_if->core_global_regs->hptxfsiz; ++ DWC_PRINTF("HPTXFSIZ @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++ ++ if (core_if->en_multiple_tx_fifo == 0) { ++ ep_num = core_if->hwcfg4.b.num_dev_perio_in_ep; ++ txfsiz = "DPTXFSIZ"; ++ } else { ++ ep_num = core_if->hwcfg4.b.num_in_eps; ++ txfsiz = "DIENPTXF"; ++ } ++ for (i = 0; i < ep_num; i++) { ++ addr = &core_if->core_global_regs->dtxfsiz[i]; ++ DWC_PRINTF("%s[%d] @0x%08lX : 0x%08X\n", txfsiz, i + 1, ++ (unsigned long)addr, DWC_READ_REG32(addr)); ++ } ++ addr = core_if->pcgcctl; ++ DWC_PRINTF("PCGCCTL @0x%08lX : 0x%08X\n", (unsigned long)addr, ++ DWC_READ_REG32(addr)); ++} ++ ++/** ++ * Flush a Tx FIFO. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param num Tx FIFO to flush. ++ */ ++void dwc_otg_flush_tx_fifo(dwc_otg_core_if_t * core_if, const int num) ++{ ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ volatile grstctl_t greset = {.d32 = 0 }; ++ int count = 0; ++ ++ DWC_DEBUGPL((DBG_CIL | DBG_PCDV), "Flush Tx FIFO %d\n", num); ++ ++ greset.b.txfflsh = 1; ++ greset.b.txfnum = num; ++ DWC_WRITE_REG32(&global_regs->grstctl, greset.d32); ++ ++ do { ++ greset.d32 = DWC_READ_REG32(&global_regs->grstctl); ++ if (++count > 10000) { ++ DWC_WARN("%s() HANG! GRSTCTL=%0x GNPTXSTS=0x%08x\n", ++ __func__, greset.d32, ++ DWC_READ_REG32(&global_regs->gnptxsts)); ++ break; ++ } ++ dwc_udelay(1); ++ } while (greset.b.txfflsh == 1); ++ ++ /* Wait for 3 PHY Clocks */ ++ dwc_udelay(1); ++} ++ ++/** ++ * Flush Rx FIFO. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++void dwc_otg_flush_rx_fifo(dwc_otg_core_if_t * core_if) ++{ ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ volatile grstctl_t greset = {.d32 = 0 }; ++ int count = 0; ++ ++ DWC_DEBUGPL((DBG_CIL | DBG_PCDV), "%s\n", __func__); ++ /* ++ * ++ */ ++ greset.b.rxfflsh = 1; ++ DWC_WRITE_REG32(&global_regs->grstctl, greset.d32); ++ ++ do { ++ greset.d32 = DWC_READ_REG32(&global_regs->grstctl); ++ if (++count > 10000) { ++ DWC_WARN("%s() HANG! GRSTCTL=%0x\n", __func__, ++ greset.d32); ++ break; ++ } ++ dwc_udelay(1); ++ } while (greset.b.rxfflsh == 1); ++ ++ /* Wait for 3 PHY Clocks */ ++ dwc_udelay(1); ++} ++ ++/** ++ * Do core a soft reset of the core. Be careful with this because it ++ * resets all the internal state machines of the core. ++ */ ++void dwc_otg_core_reset(dwc_otg_core_if_t * core_if) ++{ ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ volatile grstctl_t greset = {.d32 = 0 }; ++ int count = 0; ++ ++ DWC_DEBUGPL(DBG_CILV, "%s\n", __func__); ++ /* Wait for AHB master IDLE state. */ ++ do { ++ dwc_udelay(10); ++ greset.d32 = DWC_READ_REG32(&global_regs->grstctl); ++ if (++count > 100000) { ++ DWC_WARN("%s() HANG! AHB Idle GRSTCTL=%0x\n", __func__, ++ greset.d32); ++ return; ++ } ++ } ++ while (greset.b.ahbidle == 0); ++ ++ /* Core Soft Reset */ ++ count = 0; ++ greset.b.csftrst = 1; ++ DWC_WRITE_REG32(&global_regs->grstctl, greset.d32); ++ do { ++ greset.d32 = DWC_READ_REG32(&global_regs->grstctl); ++ if (++count > 10000) { ++ DWC_WARN("%s() HANG! Soft Reset GRSTCTL=%0x\n", ++ __func__, greset.d32); ++ break; ++ } ++ dwc_udelay(1); ++ } ++ while (greset.b.csftrst == 1); ++ ++ /* Wait for 3 PHY Clocks */ ++ dwc_mdelay(100); ++} ++ ++uint8_t dwc_otg_is_device_mode(dwc_otg_core_if_t * _core_if) ++{ ++ return (dwc_otg_mode(_core_if) != DWC_HOST_MODE); ++} ++ ++uint8_t dwc_otg_is_host_mode(dwc_otg_core_if_t * _core_if) ++{ ++ return (dwc_otg_mode(_core_if) == DWC_HOST_MODE); ++} ++ ++/** ++ * Register HCD callbacks. The callbacks are used to start and stop ++ * the HCD for interrupt processing. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param cb the HCD callback structure. ++ * @param p pointer to be passed to callback function (usb_hcd*). ++ */ ++void dwc_otg_cil_register_hcd_callbacks(dwc_otg_core_if_t * core_if, ++ dwc_otg_cil_callbacks_t * cb, void *p) ++{ ++ core_if->hcd_cb = cb; ++ cb->p = p; ++} ++ ++/** ++ * Register PCD callbacks. The callbacks are used to start and stop ++ * the PCD for interrupt processing. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param cb the PCD callback structure. ++ * @param p pointer to be passed to callback function (pcd*). ++ */ ++void dwc_otg_cil_register_pcd_callbacks(dwc_otg_core_if_t * core_if, ++ dwc_otg_cil_callbacks_t * cb, void *p) ++{ ++ core_if->pcd_cb = cb; ++ cb->p = p; ++} ++ ++#ifdef DWC_EN_ISOC ++ ++/** ++ * This function writes isoc data per 1 (micro)frame into tx fifo ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to start the transfer on. ++ * ++ */ ++void write_isoc_frame_data(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ dwc_otg_dev_in_ep_regs_t *ep_regs; ++ dtxfsts_data_t txstatus = {.d32 = 0 }; ++ uint32_t len = 0; ++ uint32_t dwords; ++ ++ ep->xfer_len = ep->data_per_frame; ++ ep->xfer_count = 0; ++ ++ ep_regs = core_if->dev_if->in_ep_regs[ep->num]; ++ ++ len = ep->xfer_len - ep->xfer_count; ++ ++ if (len > ep->maxpacket) { ++ len = ep->maxpacket; ++ } ++ ++ dwords = (len + 3) / 4; ++ ++ /* While there is space in the queue and space in the FIFO and ++ * More data to tranfer, Write packets to the Tx FIFO */ ++ txstatus.d32 = ++ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[ep->num]->dtxfsts); ++ DWC_DEBUGPL(DBG_PCDV, "b4 dtxfsts[%d]=0x%08x\n", ep->num, txstatus.d32); ++ ++ while (txstatus.b.txfspcavail > dwords && ++ ep->xfer_count < ep->xfer_len && ep->xfer_len != 0) { ++ /* Write the FIFO */ ++ dwc_otg_ep_write_packet(core_if, ep, 0); ++ ++ len = ep->xfer_len - ep->xfer_count; ++ if (len > ep->maxpacket) { ++ len = ep->maxpacket; ++ } ++ ++ dwords = (len + 3) / 4; ++ txstatus.d32 = ++ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[ep->num]-> ++ dtxfsts); ++ DWC_DEBUGPL(DBG_PCDV, "dtxfsts[%d]=0x%08x\n", ep->num, ++ txstatus.d32); ++ } ++} ++ ++/** ++ * This function initializes a descriptor chain for Isochronous transfer ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to start the transfer on. ++ * ++ */ ++void dwc_otg_iso_ep_start_frm_transfer(dwc_otg_core_if_t * core_if, ++ dwc_ep_t * ep) ++{ ++ deptsiz_data_t deptsiz = {.d32 = 0 }; ++ depctl_data_t depctl = {.d32 = 0 }; ++ dsts_data_t dsts = {.d32 = 0 }; ++ volatile uint32_t *addr; ++ ++ if (ep->is_in) { ++ addr = &core_if->dev_if->in_ep_regs[ep->num]->diepctl; ++ } else { ++ addr = &core_if->dev_if->out_ep_regs[ep->num]->doepctl; ++ } ++ ++ ep->xfer_len = ep->data_per_frame; ++ ep->xfer_count = 0; ++ ep->xfer_buff = ep->cur_pkt_addr; ++ ep->dma_addr = ep->cur_pkt_dma_addr; ++ ++ if (ep->is_in) { ++ /* Program the transfer size and packet count ++ * as follows: xfersize = N * maxpacket + ++ * short_packet pktcnt = N + (short_packet ++ * exist ? 1 : 0) ++ */ ++ deptsiz.b.xfersize = ep->xfer_len; ++ deptsiz.b.pktcnt = ++ (ep->xfer_len - 1 + ep->maxpacket) / ep->maxpacket; ++ deptsiz.b.mc = deptsiz.b.pktcnt; ++ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[ep->num]->dieptsiz, ++ deptsiz.d32); ++ ++ /* Write the DMA register */ ++ if (core_if->dma_enable) { ++ DWC_WRITE_REG32(& ++ (core_if->dev_if->in_ep_regs[ep->num]-> ++ diepdma), (uint32_t) ep->dma_addr); ++ } ++ } else { ++ deptsiz.b.pktcnt = ++ (ep->xfer_len + (ep->maxpacket - 1)) / ep->maxpacket; ++ deptsiz.b.xfersize = deptsiz.b.pktcnt * ep->maxpacket; ++ ++ DWC_WRITE_REG32(&core_if->dev_if-> ++ out_ep_regs[ep->num]->doeptsiz, deptsiz.d32); ++ ++ if (core_if->dma_enable) { ++ DWC_WRITE_REG32(& ++ (core_if->dev_if-> ++ out_ep_regs[ep->num]->doepdma), ++ (uint32_t) ep->dma_addr); ++ } ++ } ++ ++ /** Enable endpoint, clear nak */ ++ ++ depctl.d32 = 0; ++ if (ep->bInterval == 1) { ++ dsts.d32 = ++ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts); ++ ep->next_frame = dsts.b.soffn + ep->bInterval; ++ ++ if (ep->next_frame & 0x1) { ++ depctl.b.setd1pid = 1; ++ } else { ++ depctl.b.setd0pid = 1; ++ } ++ } else { ++ ep->next_frame += ep->bInterval; ++ ++ if (ep->next_frame & 0x1) { ++ depctl.b.setd1pid = 1; ++ } else { ++ depctl.b.setd0pid = 1; ++ } ++ } ++ depctl.b.epena = 1; ++ depctl.b.cnak = 1; ++ ++ DWC_MODIFY_REG32(addr, 0, depctl.d32); ++ depctl.d32 = DWC_READ_REG32(addr); ++ ++ if (ep->is_in && core_if->dma_enable == 0) { ++ write_isoc_frame_data(core_if, ep); ++ } ++ ++} ++#endif /* DWC_EN_ISOC */ ++ ++static void dwc_otg_set_uninitialized(int32_t * p, int size) ++{ ++ int i; ++ for (i = 0; i < size; i++) { ++ p[i] = -1; ++ } ++} ++ ++static int dwc_otg_param_initialized(int32_t val) ++{ ++ return val != -1; ++} ++ ++static int dwc_otg_setup_params(dwc_otg_core_if_t * core_if) ++{ ++ int i; ++ core_if->core_params = DWC_ALLOC(sizeof(*core_if->core_params)); ++ if (!core_if->core_params) { ++ return -DWC_E_NO_MEMORY; ++ } ++ dwc_otg_set_uninitialized((int32_t *) core_if->core_params, ++ sizeof(*core_if->core_params) / ++ sizeof(int32_t)); ++ DWC_PRINTF("Setting default values for core params\n"); ++ dwc_otg_set_param_otg_cap(core_if, dwc_param_otg_cap_default); ++ dwc_otg_set_param_dma_enable(core_if, dwc_param_dma_enable_default); ++ dwc_otg_set_param_dma_desc_enable(core_if, ++ dwc_param_dma_desc_enable_default); ++ dwc_otg_set_param_opt(core_if, dwc_param_opt_default); ++ dwc_otg_set_param_dma_burst_size(core_if, ++ dwc_param_dma_burst_size_default); ++ dwc_otg_set_param_host_support_fs_ls_low_power(core_if, ++ dwc_param_host_support_fs_ls_low_power_default); ++ dwc_otg_set_param_enable_dynamic_fifo(core_if, ++ dwc_param_enable_dynamic_fifo_default); ++ dwc_otg_set_param_data_fifo_size(core_if, ++ dwc_param_data_fifo_size_default); ++ dwc_otg_set_param_dev_rx_fifo_size(core_if, ++ dwc_param_dev_rx_fifo_size_default); ++ dwc_otg_set_param_dev_nperio_tx_fifo_size(core_if, ++ dwc_param_dev_nperio_tx_fifo_size_default); ++ dwc_otg_set_param_host_rx_fifo_size(core_if, ++ dwc_param_host_rx_fifo_size_default); ++ dwc_otg_set_param_host_nperio_tx_fifo_size(core_if, ++ dwc_param_host_nperio_tx_fifo_size_default); ++ dwc_otg_set_param_host_perio_tx_fifo_size(core_if, ++ dwc_param_host_perio_tx_fifo_size_default); ++ dwc_otg_set_param_max_transfer_size(core_if, ++ dwc_param_max_transfer_size_default); ++ dwc_otg_set_param_max_packet_count(core_if, ++ dwc_param_max_packet_count_default); ++ dwc_otg_set_param_host_channels(core_if, ++ dwc_param_host_channels_default); ++ dwc_otg_set_param_dev_endpoints(core_if, ++ dwc_param_dev_endpoints_default); ++ dwc_otg_set_param_phy_type(core_if, dwc_param_phy_type_default); ++ dwc_otg_set_param_speed(core_if, dwc_param_speed_default); ++ dwc_otg_set_param_host_ls_low_power_phy_clk(core_if, ++ dwc_param_host_ls_low_power_phy_clk_default); ++ dwc_otg_set_param_phy_ulpi_ddr(core_if, dwc_param_phy_ulpi_ddr_default); ++ dwc_otg_set_param_phy_ulpi_ext_vbus(core_if, ++ dwc_param_phy_ulpi_ext_vbus_default); ++ dwc_otg_set_param_phy_utmi_width(core_if, ++ dwc_param_phy_utmi_width_default); ++ dwc_otg_set_param_ts_dline(core_if, dwc_param_ts_dline_default); ++ dwc_otg_set_param_i2c_enable(core_if, dwc_param_i2c_enable_default); ++ dwc_otg_set_param_ulpi_fs_ls(core_if, dwc_param_ulpi_fs_ls_default); ++ dwc_otg_set_param_en_multiple_tx_fifo(core_if, ++ dwc_param_en_multiple_tx_fifo_default); ++ for (i = 0; i < 15; i++) { ++ dwc_otg_set_param_dev_perio_tx_fifo_size(core_if, ++ dwc_param_dev_perio_tx_fifo_size_default, ++ i); ++ } ++ ++ for (i = 0; i < 15; i++) { ++ dwc_otg_set_param_dev_tx_fifo_size(core_if, ++ dwc_param_dev_tx_fifo_size_default, ++ i); ++ } ++ dwc_otg_set_param_thr_ctl(core_if, dwc_param_thr_ctl_default); ++ dwc_otg_set_param_mpi_enable(core_if, dwc_param_mpi_enable_default); ++ dwc_otg_set_param_pti_enable(core_if, dwc_param_pti_enable_default); ++ dwc_otg_set_param_lpm_enable(core_if, dwc_param_lpm_enable_default); ++ dwc_otg_set_param_ic_usb_cap(core_if, dwc_param_ic_usb_cap_default); ++ dwc_otg_set_param_tx_thr_length(core_if, ++ dwc_param_tx_thr_length_default); ++ dwc_otg_set_param_rx_thr_length(core_if, ++ dwc_param_rx_thr_length_default); ++ dwc_otg_set_param_ahb_thr_ratio(core_if, ++ dwc_param_ahb_thr_ratio_default); ++ dwc_otg_set_param_power_down(core_if, dwc_param_power_down_default); ++ dwc_otg_set_param_reload_ctl(core_if, dwc_param_reload_ctl_default); ++ dwc_otg_set_param_dev_out_nak(core_if, dwc_param_dev_out_nak_default); ++ dwc_otg_set_param_cont_on_bna(core_if, dwc_param_cont_on_bna_default); ++ dwc_otg_set_param_ahb_single(core_if, dwc_param_ahb_single_default); ++ dwc_otg_set_param_otg_ver(core_if, dwc_param_otg_ver_default); ++ dwc_otg_set_param_adp_enable(core_if, dwc_param_adp_enable_default); ++ DWC_PRINTF("Finished setting default values for core params\n"); ++ ++ return 0; ++} ++ ++uint8_t dwc_otg_is_dma_enable(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->dma_enable; ++} ++ ++/* Checks if the parameter is outside of its valid range of values */ ++#define DWC_OTG_PARAM_TEST(_param_, _low_, _high_) \ ++ (((_param_) < (_low_)) || \ ++ ((_param_) > (_high_))) ++ ++/* Parameter access functions */ ++int dwc_otg_set_param_otg_cap(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int valid; ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 0, 2)) { ++ DWC_WARN("Wrong value for otg_cap parameter\n"); ++ DWC_WARN("otg_cap parameter must be 0,1 or 2\n"); ++ retval = -DWC_E_INVALID; ++ goto out; ++ } ++ ++ valid = 1; ++ switch (val) { ++ case DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE: ++ if (core_if->hwcfg2.b.op_mode != ++ DWC_HWCFG2_OP_MODE_HNP_SRP_CAPABLE_OTG) ++ valid = 0; ++ break; ++ case DWC_OTG_CAP_PARAM_SRP_ONLY_CAPABLE: ++ if ((core_if->hwcfg2.b.op_mode != ++ DWC_HWCFG2_OP_MODE_HNP_SRP_CAPABLE_OTG) ++ && (core_if->hwcfg2.b.op_mode != ++ DWC_HWCFG2_OP_MODE_SRP_ONLY_CAPABLE_OTG) ++ && (core_if->hwcfg2.b.op_mode != ++ DWC_HWCFG2_OP_MODE_SRP_CAPABLE_DEVICE) ++ && (core_if->hwcfg2.b.op_mode != ++ DWC_HWCFG2_OP_MODE_SRP_CAPABLE_HOST)) { ++ valid = 0; ++ } ++ break; ++ case DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE: ++ /* always valid */ ++ break; ++ } ++ if (!valid) { ++ if (dwc_otg_param_initialized(core_if->core_params->otg_cap)) { ++ DWC_ERROR ++ ("%d invalid for otg_cap paremter. Check HW configuration.\n", ++ val); ++ } ++ val = ++ (((core_if->hwcfg2.b.op_mode == ++ DWC_HWCFG2_OP_MODE_HNP_SRP_CAPABLE_OTG) ++ || (core_if->hwcfg2.b.op_mode == ++ DWC_HWCFG2_OP_MODE_SRP_ONLY_CAPABLE_OTG) ++ || (core_if->hwcfg2.b.op_mode == ++ DWC_HWCFG2_OP_MODE_SRP_CAPABLE_DEVICE) ++ || (core_if->hwcfg2.b.op_mode == ++ DWC_HWCFG2_OP_MODE_SRP_CAPABLE_HOST)) ? ++ DWC_OTG_CAP_PARAM_SRP_ONLY_CAPABLE : ++ DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE); ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->otg_cap = val; ++out: ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_otg_cap(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->otg_cap; ++} ++ ++int dwc_otg_set_param_opt(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("Wrong value for opt parameter\n"); ++ return -DWC_E_INVALID; ++ } ++ core_if->core_params->opt = val; ++ return 0; ++} ++ ++int32_t dwc_otg_get_param_opt(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->opt; ++} ++ ++int dwc_otg_set_param_dma_enable(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("Wrong value for dma enable\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if ((val == 1) && (core_if->hwcfg2.b.architecture == 0)) { ++ if (dwc_otg_param_initialized(core_if->core_params->dma_enable)) { ++ DWC_ERROR ++ ("%d invalid for dma_enable paremter. Check HW configuration.\n", ++ val); ++ } ++ val = 0; ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->dma_enable = val; ++ if (val == 0) { ++ dwc_otg_set_param_dma_desc_enable(core_if, 0); ++ } ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_dma_enable(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->dma_enable; ++} ++ ++int dwc_otg_set_param_dma_desc_enable(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("Wrong value for dma_enable\n"); ++ DWC_WARN("dma_desc_enable must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if ((val == 1) ++ && ((dwc_otg_get_param_dma_enable(core_if) == 0) ++ || (core_if->hwcfg4.b.desc_dma == 0))) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->dma_desc_enable)) { ++ DWC_ERROR ++ ("%d invalid for dma_desc_enable paremter. Check HW configuration.\n", ++ val); ++ } ++ val = 0; ++ retval = -DWC_E_INVALID; ++ } ++ core_if->core_params->dma_desc_enable = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_dma_desc_enable(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->dma_desc_enable; ++} ++ ++int dwc_otg_set_param_host_support_fs_ls_low_power(dwc_otg_core_if_t * core_if, ++ int32_t val) ++{ ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("Wrong value for host_support_fs_low_power\n"); ++ DWC_WARN("host_support_fs_low_power must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ core_if->core_params->host_support_fs_ls_low_power = val; ++ return 0; ++} ++ ++int32_t dwc_otg_get_param_host_support_fs_ls_low_power(dwc_otg_core_if_t * ++ core_if) ++{ ++ return core_if->core_params->host_support_fs_ls_low_power; ++} ++ ++int dwc_otg_set_param_enable_dynamic_fifo(dwc_otg_core_if_t * core_if, ++ int32_t val) ++{ ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("Wrong value for enable_dynamic_fifo\n"); ++ DWC_WARN("enable_dynamic_fifo must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if ((val == 1) && (core_if->hwcfg2.b.dynamic_fifo == 0)) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->enable_dynamic_fifo)) { ++ DWC_ERROR ++ ("%d invalid for enable_dynamic_fifo paremter. Check HW configuration.\n", ++ val); ++ } ++ val = 0; ++ retval = -DWC_E_INVALID; ++ } ++ core_if->core_params->enable_dynamic_fifo = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_enable_dynamic_fifo(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->enable_dynamic_fifo; ++} ++ ++int dwc_otg_set_param_data_fifo_size(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 32, 32768)) { ++ DWC_WARN("Wrong value for data_fifo_size\n"); ++ DWC_WARN("data_fifo_size must be 32-32768\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val > core_if->hwcfg3.b.dfifo_depth) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->data_fifo_size)) { ++ DWC_ERROR ++ ("%d invalid for data_fifo_size parameter. Check HW configuration.\n", ++ val); ++ } ++ val = core_if->hwcfg3.b.dfifo_depth; ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->data_fifo_size = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_data_fifo_size(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->data_fifo_size; ++} ++ ++int dwc_otg_set_param_dev_rx_fifo_size(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 16, 32768)) { ++ DWC_WARN("Wrong value for dev_rx_fifo_size\n"); ++ DWC_WARN("dev_rx_fifo_size must be 16-32768\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val > DWC_READ_REG32(&core_if->core_global_regs->grxfsiz)) { ++ if (dwc_otg_param_initialized(core_if->core_params->dev_rx_fifo_size)) { ++ DWC_WARN("%d invalid for dev_rx_fifo_size parameter\n", val); ++ } ++ val = DWC_READ_REG32(&core_if->core_global_regs->grxfsiz); ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->dev_rx_fifo_size = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_dev_rx_fifo_size(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->dev_rx_fifo_size; ++} ++ ++int dwc_otg_set_param_dev_nperio_tx_fifo_size(dwc_otg_core_if_t * core_if, ++ int32_t val) ++{ ++ int retval = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 16, 32768)) { ++ DWC_WARN("Wrong value for dev_nperio_tx_fifo\n"); ++ DWC_WARN("dev_nperio_tx_fifo must be 16-32768\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val > (DWC_READ_REG32(&core_if->core_global_regs->gnptxfsiz) >> 16)) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->dev_nperio_tx_fifo_size)) { ++ DWC_ERROR ++ ("%d invalid for dev_nperio_tx_fifo_size. Check HW configuration.\n", ++ val); ++ } ++ val = ++ (DWC_READ_REG32(&core_if->core_global_regs->gnptxfsiz) >> ++ 16); ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->dev_nperio_tx_fifo_size = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_dev_nperio_tx_fifo_size(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->dev_nperio_tx_fifo_size; ++} ++ ++int dwc_otg_set_param_host_rx_fifo_size(dwc_otg_core_if_t * core_if, ++ int32_t val) ++{ ++ int retval = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 16, 32768)) { ++ DWC_WARN("Wrong value for host_rx_fifo_size\n"); ++ DWC_WARN("host_rx_fifo_size must be 16-32768\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val > DWC_READ_REG32(&core_if->core_global_regs->grxfsiz)) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->host_rx_fifo_size)) { ++ DWC_ERROR ++ ("%d invalid for host_rx_fifo_size. Check HW configuration.\n", ++ val); ++ } ++ val = DWC_READ_REG32(&core_if->core_global_regs->grxfsiz); ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->host_rx_fifo_size = val; ++ return retval; ++ ++} ++ ++int32_t dwc_otg_get_param_host_rx_fifo_size(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->host_rx_fifo_size; ++} ++ ++int dwc_otg_set_param_host_nperio_tx_fifo_size(dwc_otg_core_if_t * core_if, ++ int32_t val) ++{ ++ int retval = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 16, 32768)) { ++ DWC_WARN("Wrong value for host_nperio_tx_fifo_size\n"); ++ DWC_WARN("host_nperio_tx_fifo_size must be 16-32768\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val > (DWC_READ_REG32(&core_if->core_global_regs->gnptxfsiz) >> 16)) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->host_nperio_tx_fifo_size)) { ++ DWC_ERROR ++ ("%d invalid for host_nperio_tx_fifo_size. Check HW configuration.\n", ++ val); ++ } ++ val = ++ (DWC_READ_REG32(&core_if->core_global_regs->gnptxfsiz) >> ++ 16); ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->host_nperio_tx_fifo_size = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_host_nperio_tx_fifo_size(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->host_nperio_tx_fifo_size; ++} ++ ++int dwc_otg_set_param_host_perio_tx_fifo_size(dwc_otg_core_if_t * core_if, ++ int32_t val) ++{ ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 16, 32768)) { ++ DWC_WARN("Wrong value for host_perio_tx_fifo_size\n"); ++ DWC_WARN("host_perio_tx_fifo_size must be 16-32768\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val > ((core_if->hptxfsiz.d32) >> 16)) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->host_perio_tx_fifo_size)) { ++ DWC_ERROR ++ ("%d invalid for host_perio_tx_fifo_size. Check HW configuration.\n", ++ val); ++ } ++ val = (core_if->hptxfsiz.d32) >> 16; ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->host_perio_tx_fifo_size = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_host_perio_tx_fifo_size(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->host_perio_tx_fifo_size; ++} ++ ++int dwc_otg_set_param_max_transfer_size(dwc_otg_core_if_t * core_if, ++ int32_t val) ++{ ++ int retval = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 2047, 524288)) { ++ DWC_WARN("Wrong value for max_transfer_size\n"); ++ DWC_WARN("max_transfer_size must be 2047-524288\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val >= (1 << (core_if->hwcfg3.b.xfer_size_cntr_width + 11))) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->max_transfer_size)) { ++ DWC_ERROR ++ ("%d invalid for max_transfer_size. Check HW configuration.\n", ++ val); ++ } ++ val = ++ ((1 << (core_if->hwcfg3.b.packet_size_cntr_width + 11)) - ++ 1); ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->max_transfer_size = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_max_transfer_size(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->max_transfer_size; ++} ++ ++int dwc_otg_set_param_max_packet_count(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 15, 511)) { ++ DWC_WARN("Wrong value for max_packet_count\n"); ++ DWC_WARN("max_packet_count must be 15-511\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val > (1 << (core_if->hwcfg3.b.packet_size_cntr_width + 4))) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->max_packet_count)) { ++ DWC_ERROR ++ ("%d invalid for max_packet_count. Check HW configuration.\n", ++ val); ++ } ++ val = ++ ((1 << (core_if->hwcfg3.b.packet_size_cntr_width + 4)) - 1); ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->max_packet_count = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_max_packet_count(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->max_packet_count; ++} ++ ++int dwc_otg_set_param_host_channels(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 1, 16)) { ++ DWC_WARN("Wrong value for host_channels\n"); ++ DWC_WARN("host_channels must be 1-16\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val > (core_if->hwcfg2.b.num_host_chan + 1)) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->host_channels)) { ++ DWC_ERROR ++ ("%d invalid for host_channels. Check HW configurations.\n", ++ val); ++ } ++ val = (core_if->hwcfg2.b.num_host_chan + 1); ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->host_channels = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_host_channels(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->host_channels; ++} ++ ++int dwc_otg_set_param_dev_endpoints(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 1, 15)) { ++ DWC_WARN("Wrong value for dev_endpoints\n"); ++ DWC_WARN("dev_endpoints must be 1-15\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val > (core_if->hwcfg2.b.num_dev_ep)) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->dev_endpoints)) { ++ DWC_ERROR ++ ("%d invalid for dev_endpoints. Check HW configurations.\n", ++ val); ++ } ++ val = core_if->hwcfg2.b.num_dev_ep; ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->dev_endpoints = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_dev_endpoints(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->dev_endpoints; ++} ++ ++int dwc_otg_set_param_phy_type(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ int valid = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 0, 2)) { ++ DWC_WARN("Wrong value for phy_type\n"); ++ DWC_WARN("phy_type must be 0,1 or 2\n"); ++ return -DWC_E_INVALID; ++ } ++#ifndef NO_FS_PHY_HW_CHECKS ++ if ((val == DWC_PHY_TYPE_PARAM_UTMI) && ++ ((core_if->hwcfg2.b.hs_phy_type == 1) || ++ (core_if->hwcfg2.b.hs_phy_type == 3))) { ++ valid = 1; ++ } else if ((val == DWC_PHY_TYPE_PARAM_ULPI) && ++ ((core_if->hwcfg2.b.hs_phy_type == 2) || ++ (core_if->hwcfg2.b.hs_phy_type == 3))) { ++ valid = 1; ++ } else if ((val == DWC_PHY_TYPE_PARAM_FS) && ++ (core_if->hwcfg2.b.fs_phy_type == 1)) { ++ valid = 1; ++ } ++ if (!valid) { ++ if (dwc_otg_param_initialized(core_if->core_params->phy_type)) { ++ DWC_ERROR ++ ("%d invalid for phy_type. Check HW configurations.\n", ++ val); ++ } ++ if (core_if->hwcfg2.b.hs_phy_type) { ++ if ((core_if->hwcfg2.b.hs_phy_type == 3) || ++ (core_if->hwcfg2.b.hs_phy_type == 1)) { ++ val = DWC_PHY_TYPE_PARAM_UTMI; ++ } else { ++ val = DWC_PHY_TYPE_PARAM_ULPI; ++ } ++ } ++ retval = -DWC_E_INVALID; ++ } ++#endif ++ core_if->core_params->phy_type = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_phy_type(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->phy_type; ++} ++ ++int dwc_otg_set_param_speed(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("Wrong value for speed parameter\n"); ++ DWC_WARN("max_speed parameter must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ if ((val == 0) ++ && dwc_otg_get_param_phy_type(core_if) == DWC_PHY_TYPE_PARAM_FS) { ++ if (dwc_otg_param_initialized(core_if->core_params->speed)) { ++ DWC_ERROR ++ ("%d invalid for speed paremter. Check HW configuration.\n", ++ val); ++ } ++ val = ++ (dwc_otg_get_param_phy_type(core_if) == ++ DWC_PHY_TYPE_PARAM_FS ? 1 : 0); ++ retval = -DWC_E_INVALID; ++ } ++ core_if->core_params->speed = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_speed(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->speed; ++} ++ ++int dwc_otg_set_param_host_ls_low_power_phy_clk(dwc_otg_core_if_t * core_if, ++ int32_t val) ++{ ++ int retval = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN ++ ("Wrong value for host_ls_low_power_phy_clk parameter\n"); ++ DWC_WARN("host_ls_low_power_phy_clk must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if ((val == DWC_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ) ++ && (dwc_otg_get_param_phy_type(core_if) == DWC_PHY_TYPE_PARAM_FS)) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->host_ls_low_power_phy_clk)) { ++ DWC_ERROR ++ ("%d invalid for host_ls_low_power_phy_clk. Check HW configuration.\n", ++ val); ++ } ++ val = ++ (dwc_otg_get_param_phy_type(core_if) == ++ DWC_PHY_TYPE_PARAM_FS) ? ++ DWC_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ : ++ DWC_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ; ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->host_ls_low_power_phy_clk = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_host_ls_low_power_phy_clk(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->host_ls_low_power_phy_clk; ++} ++ ++int dwc_otg_set_param_phy_ulpi_ddr(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("Wrong value for phy_ulpi_ddr\n"); ++ DWC_WARN("phy_upli_ddr must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->phy_ulpi_ddr = val; ++ return 0; ++} ++ ++int32_t dwc_otg_get_param_phy_ulpi_ddr(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->phy_ulpi_ddr; ++} ++ ++int dwc_otg_set_param_phy_ulpi_ext_vbus(dwc_otg_core_if_t * core_if, ++ int32_t val) ++{ ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("Wrong valaue for phy_ulpi_ext_vbus\n"); ++ DWC_WARN("phy_ulpi_ext_vbus must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->phy_ulpi_ext_vbus = val; ++ return 0; ++} ++ ++int32_t dwc_otg_get_param_phy_ulpi_ext_vbus(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->phy_ulpi_ext_vbus; ++} ++ ++int dwc_otg_set_param_phy_utmi_width(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ if (DWC_OTG_PARAM_TEST(val, 8, 8) && DWC_OTG_PARAM_TEST(val, 16, 16)) { ++ DWC_WARN("Wrong valaue for phy_utmi_width\n"); ++ DWC_WARN("phy_utmi_width must be 8 or 16\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->phy_utmi_width = val; ++ return 0; ++} ++ ++int32_t dwc_otg_get_param_phy_utmi_width(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->phy_utmi_width; ++} ++ ++int dwc_otg_set_param_ulpi_fs_ls(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("Wrong valaue for ulpi_fs_ls\n"); ++ DWC_WARN("ulpi_fs_ls must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->ulpi_fs_ls = val; ++ return 0; ++} ++ ++int32_t dwc_otg_get_param_ulpi_fs_ls(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->ulpi_fs_ls; ++} ++ ++int dwc_otg_set_param_ts_dline(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("Wrong valaue for ts_dline\n"); ++ DWC_WARN("ts_dline must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->ts_dline = val; ++ return 0; ++} ++ ++int32_t dwc_otg_get_param_ts_dline(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->ts_dline; ++} ++ ++int dwc_otg_set_param_i2c_enable(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("Wrong valaue for i2c_enable\n"); ++ DWC_WARN("i2c_enable must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++#ifndef NO_FS_PHY_HW_CHECK ++ if (val == 1 && core_if->hwcfg3.b.i2c == 0) { ++ if (dwc_otg_param_initialized(core_if->core_params->i2c_enable)) { ++ DWC_ERROR ++ ("%d invalid for i2c_enable. Check HW configuration.\n", ++ val); ++ } ++ val = 0; ++ retval = -DWC_E_INVALID; ++ } ++#endif ++ ++ core_if->core_params->i2c_enable = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_i2c_enable(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->i2c_enable; ++} ++ ++int dwc_otg_set_param_dev_perio_tx_fifo_size(dwc_otg_core_if_t * core_if, ++ int32_t val, int fifo_num) ++{ ++ int retval = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 4, 768)) { ++ DWC_WARN("Wrong value for dev_perio_tx_fifo_size\n"); ++ DWC_WARN("dev_perio_tx_fifo_size must be 4-768\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val > ++ (DWC_READ_REG32(&core_if->core_global_regs->dtxfsiz[fifo_num]))) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->dev_perio_tx_fifo_size[fifo_num])) { ++ DWC_ERROR ++ ("`%d' invalid for parameter `dev_perio_fifo_size_%d'. Check HW configuration.\n", ++ val, fifo_num); ++ } ++ val = (DWC_READ_REG32(&core_if->core_global_regs->dtxfsiz[fifo_num])); ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->dev_perio_tx_fifo_size[fifo_num] = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_dev_perio_tx_fifo_size(dwc_otg_core_if_t * core_if, ++ int fifo_num) ++{ ++ return core_if->core_params->dev_perio_tx_fifo_size[fifo_num]; ++} ++ ++int dwc_otg_set_param_en_multiple_tx_fifo(dwc_otg_core_if_t * core_if, ++ int32_t val) ++{ ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("Wrong valaue for en_multiple_tx_fifo,\n"); ++ DWC_WARN("en_multiple_tx_fifo must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val == 1 && core_if->hwcfg4.b.ded_fifo_en == 0) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->en_multiple_tx_fifo)) { ++ DWC_ERROR ++ ("%d invalid for parameter en_multiple_tx_fifo. Check HW configuration.\n", ++ val); ++ } ++ val = 0; ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->en_multiple_tx_fifo = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_en_multiple_tx_fifo(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->en_multiple_tx_fifo; ++} ++ ++int dwc_otg_set_param_dev_tx_fifo_size(dwc_otg_core_if_t * core_if, int32_t val, ++ int fifo_num) ++{ ++ int retval = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 4, 768)) { ++ DWC_WARN("Wrong value for dev_tx_fifo_size\n"); ++ DWC_WARN("dev_tx_fifo_size must be 4-768\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val > ++ (DWC_READ_REG32(&core_if->core_global_regs->dtxfsiz[fifo_num]))) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->dev_tx_fifo_size[fifo_num])) { ++ DWC_ERROR ++ ("`%d' invalid for parameter `dev_tx_fifo_size_%d'. Check HW configuration.\n", ++ val, fifo_num); ++ } ++ val = (DWC_READ_REG32(&core_if->core_global_regs->dtxfsiz[fifo_num])); ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->dev_tx_fifo_size[fifo_num] = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_dev_tx_fifo_size(dwc_otg_core_if_t * core_if, ++ int fifo_num) ++{ ++ return core_if->core_params->dev_tx_fifo_size[fifo_num]; ++} ++ ++int dwc_otg_set_param_thr_ctl(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 0, 7)) { ++ DWC_WARN("Wrong value for thr_ctl\n"); ++ DWC_WARN("thr_ctl must be 0-7\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if ((val != 0) && ++ (!dwc_otg_get_param_dma_enable(core_if) || ++ !core_if->hwcfg4.b.ded_fifo_en)) { ++ if (dwc_otg_param_initialized(core_if->core_params->thr_ctl)) { ++ DWC_ERROR ++ ("%d invalid for parameter thr_ctl. Check HW configuration.\n", ++ val); ++ } ++ val = 0; ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->thr_ctl = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_thr_ctl(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->thr_ctl; ++} ++ ++int dwc_otg_set_param_lpm_enable(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("Wrong value for lpm_enable\n"); ++ DWC_WARN("lpm_enable must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val && !core_if->hwcfg3.b.otg_lpm_en) { ++ if (dwc_otg_param_initialized(core_if->core_params->lpm_enable)) { ++ DWC_ERROR ++ ("%d invalid for parameter lpm_enable. Check HW configuration.\n", ++ val); ++ } ++ val = 0; ++ retval = -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->lpm_enable = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_lpm_enable(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->lpm_enable; ++} ++ ++int dwc_otg_set_param_tx_thr_length(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ if (DWC_OTG_PARAM_TEST(val, 8, 128)) { ++ DWC_WARN("Wrong valaue for tx_thr_length\n"); ++ DWC_WARN("tx_thr_length must be 8 - 128\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->tx_thr_length = val; ++ return 0; ++} ++ ++int32_t dwc_otg_get_param_tx_thr_length(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->tx_thr_length; ++} ++ ++int dwc_otg_set_param_rx_thr_length(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ if (DWC_OTG_PARAM_TEST(val, 8, 128)) { ++ DWC_WARN("Wrong valaue for rx_thr_length\n"); ++ DWC_WARN("rx_thr_length must be 8 - 128\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->rx_thr_length = val; ++ return 0; ++} ++ ++int32_t dwc_otg_get_param_rx_thr_length(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->rx_thr_length; ++} ++ ++int dwc_otg_set_param_dma_burst_size(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ if (DWC_OTG_PARAM_TEST(val, 1, 1) && ++ DWC_OTG_PARAM_TEST(val, 4, 4) && ++ DWC_OTG_PARAM_TEST(val, 8, 8) && ++ DWC_OTG_PARAM_TEST(val, 16, 16) && ++ DWC_OTG_PARAM_TEST(val, 32, 32) && ++ DWC_OTG_PARAM_TEST(val, 64, 64) && ++ DWC_OTG_PARAM_TEST(val, 128, 128) && ++ DWC_OTG_PARAM_TEST(val, 256, 256)) { ++ DWC_WARN("`%d' invalid for parameter `dma_burst_size'\n", val); ++ return -DWC_E_INVALID; ++ } ++ core_if->core_params->dma_burst_size = val; ++ return 0; ++} ++ ++int32_t dwc_otg_get_param_dma_burst_size(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->dma_burst_size; ++} ++ ++int dwc_otg_set_param_pti_enable(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("`%d' invalid for parameter `pti_enable'\n", val); ++ return -DWC_E_INVALID; ++ } ++ if (val && (core_if->snpsid < OTG_CORE_REV_2_72a)) { ++ if (dwc_otg_param_initialized(core_if->core_params->pti_enable)) { ++ DWC_ERROR ++ ("%d invalid for parameter pti_enable. Check HW configuration.\n", ++ val); ++ } ++ retval = -DWC_E_INVALID; ++ val = 0; ++ } ++ core_if->core_params->pti_enable = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_pti_enable(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->pti_enable; ++} ++ ++int dwc_otg_set_param_mpi_enable(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("`%d' invalid for parameter `mpi_enable'\n", val); ++ return -DWC_E_INVALID; ++ } ++ if (val && (core_if->hwcfg2.b.multi_proc_int == 0)) { ++ if (dwc_otg_param_initialized(core_if->core_params->mpi_enable)) { ++ DWC_ERROR ++ ("%d invalid for parameter mpi_enable. Check HW configuration.\n", ++ val); ++ } ++ retval = -DWC_E_INVALID; ++ val = 0; ++ } ++ core_if->core_params->mpi_enable = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_mpi_enable(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->mpi_enable; ++} ++ ++int dwc_otg_set_param_adp_enable(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("`%d' invalid for parameter `adp_enable'\n", val); ++ return -DWC_E_INVALID; ++ } ++ if (val && (core_if->hwcfg3.b.adp_supp == 0)) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->adp_supp_enable)) { ++ DWC_ERROR ++ ("%d invalid for parameter adp_enable. Check HW configuration.\n", ++ val); ++ } ++ retval = -DWC_E_INVALID; ++ val = 0; ++ } ++ core_if->core_params->adp_supp_enable = val; ++ /*Set OTG version 2.0 in case of enabling ADP*/ ++ if (val) ++ dwc_otg_set_param_otg_ver(core_if, 1); ++ ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_adp_enable(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->adp_supp_enable; ++} ++ ++int dwc_otg_set_param_ic_usb_cap(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("`%d' invalid for parameter `ic_usb_cap'\n", val); ++ DWC_WARN("ic_usb_cap must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val && (core_if->hwcfg2.b.otg_enable_ic_usb == 0)) { ++ if (dwc_otg_param_initialized(core_if->core_params->ic_usb_cap)) { ++ DWC_ERROR ++ ("%d invalid for parameter ic_usb_cap. Check HW configuration.\n", ++ val); ++ } ++ retval = -DWC_E_INVALID; ++ val = 0; ++ } ++ core_if->core_params->ic_usb_cap = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_ic_usb_cap(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->ic_usb_cap; ++} ++ ++int dwc_otg_set_param_ahb_thr_ratio(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ int valid = 1; ++ ++ if (DWC_OTG_PARAM_TEST(val, 0, 3)) { ++ DWC_WARN("`%d' invalid for parameter `ahb_thr_ratio'\n", val); ++ DWC_WARN("ahb_thr_ratio must be 0 - 3\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (val ++ && (core_if->snpsid < OTG_CORE_REV_2_81a ++ || !dwc_otg_get_param_thr_ctl(core_if))) { ++ valid = 0; ++ } else if (val ++ && ((dwc_otg_get_param_tx_thr_length(core_if) / (1 << val)) < ++ 4)) { ++ valid = 0; ++ } ++ if (valid == 0) { ++ if (dwc_otg_param_initialized ++ (core_if->core_params->ahb_thr_ratio)) { ++ DWC_ERROR ++ ("%d invalid for parameter ahb_thr_ratio. Check HW configuration.\n", ++ val); ++ } ++ retval = -DWC_E_INVALID; ++ val = 0; ++ } ++ ++ core_if->core_params->ahb_thr_ratio = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_ahb_thr_ratio(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->ahb_thr_ratio; ++} ++ ++int dwc_otg_set_param_power_down(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ int valid = 1; ++ hwcfg4_data_t hwcfg4 = {.d32 = 0 }; ++ hwcfg4.d32 = DWC_READ_REG32(&core_if->core_global_regs->ghwcfg4); ++ ++ if (DWC_OTG_PARAM_TEST(val, 0, 3)) { ++ DWC_WARN("`%d' invalid for parameter `power_down'\n", val); ++ DWC_WARN("power_down must be 0 - 2\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if ((val == 2) && (core_if->snpsid < OTG_CORE_REV_2_91a)) { ++ valid = 0; ++ } ++ if ((val == 3) ++ && ((core_if->snpsid < OTG_CORE_REV_3_00a) ++ || (hwcfg4.b.xhiber == 0))) { ++ valid = 0; ++ } ++ if (valid == 0) { ++ if (dwc_otg_param_initialized(core_if->core_params->power_down)) { ++ DWC_ERROR ++ ("%d invalid for parameter power_down. Check HW configuration.\n", ++ val); ++ } ++ retval = -DWC_E_INVALID; ++ val = 0; ++ } ++ core_if->core_params->power_down = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_power_down(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->power_down; ++} ++ ++int dwc_otg_set_param_reload_ctl(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ int valid = 1; ++ ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("`%d' invalid for parameter `reload_ctl'\n", val); ++ DWC_WARN("reload_ctl must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if ((val == 1) && (core_if->snpsid < OTG_CORE_REV_2_92a)) { ++ valid = 0; ++ } ++ if (valid == 0) { ++ if (dwc_otg_param_initialized(core_if->core_params->reload_ctl)) { ++ DWC_ERROR("%d invalid for parameter reload_ctl." ++ "Check HW configuration.\n", val); ++ } ++ retval = -DWC_E_INVALID; ++ val = 0; ++ } ++ core_if->core_params->reload_ctl = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_reload_ctl(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->reload_ctl; ++} ++ ++int dwc_otg_set_param_dev_out_nak(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ int valid = 1; ++ ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("`%d' invalid for parameter `dev_out_nak'\n", val); ++ DWC_WARN("dev_out_nak must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if ((val == 1) && ((core_if->snpsid < OTG_CORE_REV_2_93a) || ++ !(core_if->core_params->dma_desc_enable))) { ++ valid = 0; ++ } ++ if (valid == 0) { ++ if (dwc_otg_param_initialized(core_if->core_params->dev_out_nak)) { ++ DWC_ERROR("%d invalid for parameter dev_out_nak." ++ "Check HW configuration.\n", val); ++ } ++ retval = -DWC_E_INVALID; ++ val = 0; ++ } ++ core_if->core_params->dev_out_nak = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_dev_out_nak(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->dev_out_nak; ++} ++ ++int dwc_otg_set_param_cont_on_bna(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ int valid = 1; ++ ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("`%d' invalid for parameter `cont_on_bna'\n", val); ++ DWC_WARN("cont_on_bna must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if ((val == 1) && ((core_if->snpsid < OTG_CORE_REV_2_94a) || ++ !(core_if->core_params->dma_desc_enable))) { ++ valid = 0; ++ } ++ if (valid == 0) { ++ if (dwc_otg_param_initialized(core_if->core_params->cont_on_bna)) { ++ DWC_ERROR("%d invalid for parameter cont_on_bna." ++ "Check HW configuration.\n", val); ++ } ++ retval = -DWC_E_INVALID; ++ val = 0; ++ } ++ core_if->core_params->cont_on_bna = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_cont_on_bna(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->cont_on_bna; ++} ++ ++int dwc_otg_set_param_ahb_single(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ int valid = 1; ++ ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("`%d' invalid for parameter `ahb_single'\n", val); ++ DWC_WARN("ahb_single must be 0 or 1\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if ((val == 1) && (core_if->snpsid < OTG_CORE_REV_2_94a)) { ++ valid = 0; ++ } ++ if (valid == 0) { ++ if (dwc_otg_param_initialized(core_if->core_params->ahb_single)) { ++ DWC_ERROR("%d invalid for parameter ahb_single." ++ "Check HW configuration.\n", val); ++ } ++ retval = -DWC_E_INVALID; ++ val = 0; ++ } ++ core_if->core_params->ahb_single = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_ahb_single(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->ahb_single; ++} ++ ++int dwc_otg_set_param_otg_ver(dwc_otg_core_if_t * core_if, int32_t val) ++{ ++ int retval = 0; ++ ++ if (DWC_OTG_PARAM_TEST(val, 0, 1)) { ++ DWC_WARN("`%d' invalid for parameter `otg_ver'\n", val); ++ DWC_WARN ++ ("otg_ver must be 0(for OTG 1.3 support) or 1(for OTG 2.0 support)\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ core_if->core_params->otg_ver = val; ++ return retval; ++} ++ ++int32_t dwc_otg_get_param_otg_ver(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->core_params->otg_ver; ++} ++ ++uint32_t dwc_otg_get_hnpstatus(dwc_otg_core_if_t * core_if) ++{ ++ gotgctl_data_t otgctl; ++ otgctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->gotgctl); ++ return otgctl.b.hstnegscs; ++} ++ ++uint32_t dwc_otg_get_srpstatus(dwc_otg_core_if_t * core_if) ++{ ++ gotgctl_data_t otgctl; ++ otgctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->gotgctl); ++ return otgctl.b.sesreqscs; ++} ++ ++void dwc_otg_set_hnpreq(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ if(core_if->otg_ver == 0) { ++ gotgctl_data_t otgctl; ++ otgctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->gotgctl); ++ otgctl.b.hnpreq = val; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gotgctl, otgctl.d32); ++ } else { ++ core_if->otg_sts = val; ++ } ++} ++ ++uint32_t dwc_otg_get_gsnpsid(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->snpsid; ++} ++ ++uint32_t dwc_otg_get_mode(dwc_otg_core_if_t * core_if) ++{ ++ gintsts_data_t gintsts; ++ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts); ++ return gintsts.b.curmode; ++} ++ ++uint32_t dwc_otg_get_hnpcapable(dwc_otg_core_if_t * core_if) ++{ ++ gusbcfg_data_t usbcfg; ++ usbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg); ++ return usbcfg.b.hnpcap; ++} ++ ++void dwc_otg_set_hnpcapable(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ gusbcfg_data_t usbcfg; ++ usbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg); ++ usbcfg.b.hnpcap = val; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, usbcfg.d32); ++} ++ ++uint32_t dwc_otg_get_srpcapable(dwc_otg_core_if_t * core_if) ++{ ++ gusbcfg_data_t usbcfg; ++ usbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg); ++ return usbcfg.b.srpcap; ++} ++ ++void dwc_otg_set_srpcapable(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ gusbcfg_data_t usbcfg; ++ usbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg); ++ usbcfg.b.srpcap = val; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, usbcfg.d32); ++} ++ ++uint32_t dwc_otg_get_devspeed(dwc_otg_core_if_t * core_if) ++{ ++ dcfg_data_t dcfg; ++ /* originally: dcfg.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg); */ ++ ++ dcfg.d32 = -1; //GRAYG ++ DWC_DEBUGPL(DBG_CILV, "%s - core_if(%p)\n", __func__, core_if); ++ if (NULL == core_if) ++ DWC_ERROR("reg request with NULL core_if\n"); ++ DWC_DEBUGPL(DBG_CILV, "%s - core_if(%p)->dev_if(%p)\n", __func__, ++ core_if, core_if->dev_if); ++ if (NULL == core_if->dev_if) ++ DWC_ERROR("reg request with NULL dev_if\n"); ++ DWC_DEBUGPL(DBG_CILV, "%s - core_if(%p)->dev_if(%p)->" ++ "dev_global_regs(%p)\n", __func__, ++ core_if, core_if->dev_if, ++ core_if->dev_if->dev_global_regs); ++ if (NULL == core_if->dev_if->dev_global_regs) ++ DWC_ERROR("reg request with NULL dev_global_regs\n"); ++ else { ++ DWC_DEBUGPL(DBG_CILV, "%s - &core_if(%p)->dev_if(%p)->" ++ "dev_global_regs(%p)->dcfg = %p\n", __func__, ++ core_if, core_if->dev_if, ++ core_if->dev_if->dev_global_regs, ++ &core_if->dev_if->dev_global_regs->dcfg); ++ dcfg.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg); ++ } ++ return dcfg.b.devspd; ++} ++ ++void dwc_otg_set_devspeed(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ dcfg_data_t dcfg; ++ dcfg.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg); ++ dcfg.b.devspd = val; ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg, dcfg.d32); ++} ++ ++uint32_t dwc_otg_get_busconnected(dwc_otg_core_if_t * core_if) ++{ ++ hprt0_data_t hprt0; ++ hprt0.d32 = DWC_READ_REG32(core_if->host_if->hprt0); ++ return hprt0.b.prtconnsts; ++} ++ ++uint32_t dwc_otg_get_enumspeed(dwc_otg_core_if_t * core_if) ++{ ++ dsts_data_t dsts; ++ dsts.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts); ++ return dsts.b.enumspd; ++} ++ ++uint32_t dwc_otg_get_prtpower(dwc_otg_core_if_t * core_if) ++{ ++ hprt0_data_t hprt0; ++ hprt0.d32 = DWC_READ_REG32(core_if->host_if->hprt0); ++ return hprt0.b.prtpwr; ++ ++} ++ ++uint32_t dwc_otg_get_core_state(dwc_otg_core_if_t * core_if) ++{ ++ return core_if->hibernation_suspend; ++} ++ ++void dwc_otg_set_prtpower(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ hprt0_data_t hprt0; ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtpwr = val; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++} ++ ++uint32_t dwc_otg_get_prtsuspend(dwc_otg_core_if_t * core_if) ++{ ++ hprt0_data_t hprt0; ++ hprt0.d32 = DWC_READ_REG32(core_if->host_if->hprt0); ++ return hprt0.b.prtsusp; ++ ++} ++ ++void dwc_otg_set_prtsuspend(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ hprt0_data_t hprt0; ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtsusp = val; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++} ++ ++uint32_t dwc_otg_get_fr_interval(dwc_otg_core_if_t * core_if) ++{ ++ hfir_data_t hfir; ++ hfir.d32 = DWC_READ_REG32(&core_if->host_if->host_global_regs->hfir); ++ return hfir.b.frint; ++ ++} ++ ++void dwc_otg_set_fr_interval(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ hfir_data_t hfir; ++ uint32_t fram_int; ++ fram_int = calc_frame_interval(core_if); ++ hfir.d32 = DWC_READ_REG32(&core_if->host_if->host_global_regs->hfir); ++ if (!core_if->core_params->reload_ctl) { ++ DWC_WARN("\nCannot reload HFIR register.HFIR.HFIRRldCtrl bit is" ++ "not set to 1.\nShould load driver with reload_ctl=1" ++ " module parameter\n"); ++ return; ++ } ++ switch (fram_int) { ++ case 3750: ++ if ((val < 3350) || (val > 4150)) { ++ DWC_WARN("HFIR interval for HS core and 30 MHz" ++ "clock freq should be from 3350 to 4150\n"); ++ return; ++ } ++ break; ++ case 30000: ++ if ((val < 26820) || (val > 33180)) { ++ DWC_WARN("HFIR interval for FS/LS core and 30 MHz" ++ "clock freq should be from 26820 to 33180\n"); ++ return; ++ } ++ break; ++ case 6000: ++ if ((val < 5360) || (val > 6640)) { ++ DWC_WARN("HFIR interval for HS core and 48 MHz" ++ "clock freq should be from 5360 to 6640\n"); ++ return; ++ } ++ break; ++ case 48000: ++ if ((val < 42912) || (val > 53088)) { ++ DWC_WARN("HFIR interval for FS/LS core and 48 MHz" ++ "clock freq should be from 42912 to 53088\n"); ++ return; ++ } ++ break; ++ case 7500: ++ if ((val < 6700) || (val > 8300)) { ++ DWC_WARN("HFIR interval for HS core and 60 MHz" ++ "clock freq should be from 6700 to 8300\n"); ++ return; ++ } ++ break; ++ case 60000: ++ if ((val < 53640) || (val > 65536)) { ++ DWC_WARN("HFIR interval for FS/LS core and 60 MHz" ++ "clock freq should be from 53640 to 65536\n"); ++ return; ++ } ++ break; ++ default: ++ DWC_WARN("Unknown frame interval\n"); ++ return; ++ break; ++ ++ } ++ hfir.b.frint = val; ++ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hfir, hfir.d32); ++} ++ ++uint32_t dwc_otg_get_mode_ch_tim(dwc_otg_core_if_t * core_if) ++{ ++ hcfg_data_t hcfg; ++ hcfg.d32 = DWC_READ_REG32(&core_if->host_if->host_global_regs->hcfg); ++ return hcfg.b.modechtimen; ++ ++} ++ ++void dwc_otg_set_mode_ch_tim(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ hcfg_data_t hcfg; ++ hcfg.d32 = DWC_READ_REG32(&core_if->host_if->host_global_regs->hcfg); ++ hcfg.b.modechtimen = val; ++ DWC_WRITE_REG32(&core_if->host_if->host_global_regs->hcfg, hcfg.d32); ++} ++ ++void dwc_otg_set_prtresume(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ hprt0_data_t hprt0; ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtres = val; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++} ++ ++uint32_t dwc_otg_get_remotewakesig(dwc_otg_core_if_t * core_if) ++{ ++ dctl_data_t dctl; ++ dctl.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dctl); ++ return dctl.b.rmtwkupsig; ++} ++ ++uint32_t dwc_otg_get_lpm_portsleepstatus(dwc_otg_core_if_t * core_if) ++{ ++ glpmcfg_data_t lpmcfg; ++ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ ++ DWC_ASSERT(! ++ ((core_if->lx_state == DWC_OTG_L1) ^ lpmcfg.b.prt_sleep_sts), ++ "lx_state = %d, lmpcfg.prt_sleep_sts = %d\n", ++ core_if->lx_state, lpmcfg.b.prt_sleep_sts); ++ ++ return lpmcfg.b.prt_sleep_sts; ++} ++ ++uint32_t dwc_otg_get_lpm_remotewakeenabled(dwc_otg_core_if_t * core_if) ++{ ++ glpmcfg_data_t lpmcfg; ++ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ return lpmcfg.b.rem_wkup_en; ++} ++ ++uint32_t dwc_otg_get_lpmresponse(dwc_otg_core_if_t * core_if) ++{ ++ glpmcfg_data_t lpmcfg; ++ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ return lpmcfg.b.appl_resp; ++} ++ ++void dwc_otg_set_lpmresponse(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ glpmcfg_data_t lpmcfg; ++ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ lpmcfg.b.appl_resp = val; ++ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg, lpmcfg.d32); ++} ++ ++uint32_t dwc_otg_get_hsic_connect(dwc_otg_core_if_t * core_if) ++{ ++ glpmcfg_data_t lpmcfg; ++ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ return lpmcfg.b.hsic_connect; ++} ++ ++void dwc_otg_set_hsic_connect(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ glpmcfg_data_t lpmcfg; ++ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ lpmcfg.b.hsic_connect = val; ++ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg, lpmcfg.d32); ++} ++ ++uint32_t dwc_otg_get_inv_sel_hsic(dwc_otg_core_if_t * core_if) ++{ ++ glpmcfg_data_t lpmcfg; ++ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ return lpmcfg.b.inv_sel_hsic; ++ ++} ++ ++void dwc_otg_set_inv_sel_hsic(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ glpmcfg_data_t lpmcfg; ++ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ lpmcfg.b.inv_sel_hsic = val; ++ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg, lpmcfg.d32); ++} ++ ++uint32_t dwc_otg_get_gotgctl(dwc_otg_core_if_t * core_if) ++{ ++ return DWC_READ_REG32(&core_if->core_global_regs->gotgctl); ++} ++ ++void dwc_otg_set_gotgctl(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gotgctl, val); ++} ++ ++uint32_t dwc_otg_get_gusbcfg(dwc_otg_core_if_t * core_if) ++{ ++ return DWC_READ_REG32(&core_if->core_global_regs->gusbcfg); ++} ++ ++void dwc_otg_set_gusbcfg(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, val); ++} ++ ++uint32_t dwc_otg_get_grxfsiz(dwc_otg_core_if_t * core_if) ++{ ++ return DWC_READ_REG32(&core_if->core_global_regs->grxfsiz); ++} ++ ++void dwc_otg_set_grxfsiz(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ DWC_WRITE_REG32(&core_if->core_global_regs->grxfsiz, val); ++} ++ ++uint32_t dwc_otg_get_gnptxfsiz(dwc_otg_core_if_t * core_if) ++{ ++ return DWC_READ_REG32(&core_if->core_global_regs->gnptxfsiz); ++} ++ ++void dwc_otg_set_gnptxfsiz(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gnptxfsiz, val); ++} ++ ++uint32_t dwc_otg_get_gpvndctl(dwc_otg_core_if_t * core_if) ++{ ++ return DWC_READ_REG32(&core_if->core_global_regs->gpvndctl); ++} ++ ++void dwc_otg_set_gpvndctl(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gpvndctl, val); ++} ++ ++uint32_t dwc_otg_get_ggpio(dwc_otg_core_if_t * core_if) ++{ ++ return DWC_READ_REG32(&core_if->core_global_regs->ggpio); ++} ++ ++void dwc_otg_set_ggpio(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ DWC_WRITE_REG32(&core_if->core_global_regs->ggpio, val); ++} ++ ++uint32_t dwc_otg_get_hprt0(dwc_otg_core_if_t * core_if) ++{ ++ return DWC_READ_REG32(core_if->host_if->hprt0); ++ ++} ++ ++void dwc_otg_set_hprt0(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ DWC_WRITE_REG32(core_if->host_if->hprt0, val); ++} ++ ++uint32_t dwc_otg_get_guid(dwc_otg_core_if_t * core_if) ++{ ++ return DWC_READ_REG32(&core_if->core_global_regs->guid); ++} ++ ++void dwc_otg_set_guid(dwc_otg_core_if_t * core_if, uint32_t val) ++{ ++ DWC_WRITE_REG32(&core_if->core_global_regs->guid, val); ++} ++ ++uint32_t dwc_otg_get_hptxfsiz(dwc_otg_core_if_t * core_if) ++{ ++ return DWC_READ_REG32(&core_if->core_global_regs->hptxfsiz); ++} ++ ++uint16_t dwc_otg_get_otg_version(dwc_otg_core_if_t * core_if) ++{ ++ return ((core_if->otg_ver == 1) ? (uint16_t)0x0200 : (uint16_t)0x0103); ++} ++ ++/** ++ * Start the SRP timer to detect when the SRP does not complete within ++ * 6 seconds. ++ * ++ * @param core_if the pointer to core_if strucure. ++ */ ++void dwc_otg_pcd_start_srp_timer(dwc_otg_core_if_t * core_if) ++{ ++ core_if->srp_timer_started = 1; ++ DWC_TIMER_SCHEDULE(core_if->srp_timer, 6000 /* 6 secs */ ); ++} ++ ++void dwc_otg_initiate_srp(dwc_otg_core_if_t * core_if) ++{ ++ uint32_t *addr = (uint32_t *) & (core_if->core_global_regs->gotgctl); ++ gotgctl_data_t mem; ++ gotgctl_data_t val; ++ ++ val.d32 = DWC_READ_REG32(addr); ++ if (val.b.sesreq) { ++ DWC_ERROR("Session Request Already active!\n"); ++ return; ++ } ++ ++ DWC_INFO("Session Request Initated\n"); //NOTICE ++ mem.d32 = DWC_READ_REG32(addr); ++ mem.b.sesreq = 1; ++ DWC_WRITE_REG32(addr, mem.d32); ++ ++ /* Start the SRP timer */ ++ dwc_otg_pcd_start_srp_timer(core_if); ++ return; ++} +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_cil.h +@@ -0,0 +1,1464 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_cil.h $ ++ * $Revision: #123 $ ++ * $Date: 2012/08/10 $ ++ * $Change: 2047372 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++#if !defined(__DWC_CIL_H__) ++#define __DWC_CIL_H__ ++ ++#include "dwc_list.h" ++#include "dwc_otg_dbg.h" ++#include "dwc_otg_regs.h" ++ ++#include "dwc_otg_core_if.h" ++#include "dwc_otg_adp.h" ++ ++/** ++ * @file ++ * This file contains the interface to the Core Interface Layer. ++ */ ++ ++#ifdef DWC_UTE_CFI ++ ++#define MAX_DMA_DESCS_PER_EP 256 ++ ++/** ++ * Enumeration for the data buffer mode ++ */ ++typedef enum _data_buffer_mode { ++ BM_STANDARD = 0, /* data buffer is in normal mode */ ++ BM_SG = 1, /* data buffer uses the scatter/gather mode */ ++ BM_CONCAT = 2, /* data buffer uses the concatenation mode */ ++ BM_CIRCULAR = 3, /* data buffer uses the circular DMA mode */ ++ BM_ALIGN = 4 /* data buffer is in buffer alignment mode */ ++} data_buffer_mode_e; ++#endif //DWC_UTE_CFI ++ ++/** Macros defined for DWC OTG HW Release version */ ++ ++#define OTG_CORE_REV_2_60a 0x4F54260A ++#define OTG_CORE_REV_2_71a 0x4F54271A ++#define OTG_CORE_REV_2_72a 0x4F54272A ++#define OTG_CORE_REV_2_80a 0x4F54280A ++#define OTG_CORE_REV_2_81a 0x4F54281A ++#define OTG_CORE_REV_2_90a 0x4F54290A ++#define OTG_CORE_REV_2_91a 0x4F54291A ++#define OTG_CORE_REV_2_92a 0x4F54292A ++#define OTG_CORE_REV_2_93a 0x4F54293A ++#define OTG_CORE_REV_2_94a 0x4F54294A ++#define OTG_CORE_REV_3_00a 0x4F54300A ++ ++/** ++ * Information for each ISOC packet. ++ */ ++typedef struct iso_pkt_info { ++ uint32_t offset; ++ uint32_t length; ++ int32_t status; ++} iso_pkt_info_t; ++ ++/** ++ * The dwc_ep structure represents the state of a single ++ * endpoint when acting in device mode. It contains the data items ++ * needed for an endpoint to be activated and transfer packets. ++ */ ++typedef struct dwc_ep { ++ /** EP number used for register address lookup */ ++ uint8_t num; ++ /** EP direction 0 = OUT */ ++ unsigned is_in:1; ++ /** EP active. */ ++ unsigned active:1; ++ ++ /** ++ * Periodic Tx FIFO # for IN EPs For INTR EP set to 0 to use non-periodic ++ * Tx FIFO. If dedicated Tx FIFOs are enabled Tx FIFO # FOR IN EPs*/ ++ unsigned tx_fifo_num:4; ++ /** EP type: 0 - Control, 1 - ISOC, 2 - BULK, 3 - INTR */ ++ unsigned type:2; ++#define DWC_OTG_EP_TYPE_CONTROL 0 ++#define DWC_OTG_EP_TYPE_ISOC 1 ++#define DWC_OTG_EP_TYPE_BULK 2 ++#define DWC_OTG_EP_TYPE_INTR 3 ++ ++ /** DATA start PID for INTR and BULK EP */ ++ unsigned data_pid_start:1; ++ /** Frame (even/odd) for ISOC EP */ ++ unsigned even_odd_frame:1; ++ /** Max Packet bytes */ ++ unsigned maxpacket:11; ++ ++ /** Max Transfer size */ ++ uint32_t maxxfer; ++ ++ /** @name Transfer state */ ++ /** @{ */ ++ ++ /** ++ * Pointer to the beginning of the transfer buffer -- do not modify ++ * during transfer. ++ */ ++ ++ dwc_dma_t dma_addr; ++ ++ dwc_dma_t dma_desc_addr; ++ dwc_otg_dev_dma_desc_t *desc_addr; ++ ++ uint8_t *start_xfer_buff; ++ /** pointer to the transfer buffer */ ++ uint8_t *xfer_buff; ++ /** Number of bytes to transfer */ ++ unsigned xfer_len:19; ++ /** Number of bytes transferred. */ ++ unsigned xfer_count:19; ++ /** Sent ZLP */ ++ unsigned sent_zlp:1; ++ /** Total len for control transfer */ ++ unsigned total_len:19; ++ ++ /** stall clear flag */ ++ unsigned stall_clear_flag:1; ++ ++ /** SETUP pkt cnt rollover flag for EP0 out*/ ++ unsigned stp_rollover; ++ ++#ifdef DWC_UTE_CFI ++ /* The buffer mode */ ++ data_buffer_mode_e buff_mode; ++ ++ /* The chain of DMA descriptors. ++ * MAX_DMA_DESCS_PER_EP will be allocated for each active EP. ++ */ ++ dwc_otg_dma_desc_t *descs; ++ ++ /* The DMA address of the descriptors chain start */ ++ dma_addr_t descs_dma_addr; ++ /** This variable stores the length of the last enqueued request */ ++ uint32_t cfi_req_len; ++#endif //DWC_UTE_CFI ++ ++/** Max DMA Descriptor count for any EP */ ++#define MAX_DMA_DESC_CNT 256 ++ /** Allocated DMA Desc count */ ++ uint32_t desc_cnt; ++ ++ /** bInterval */ ++ uint32_t bInterval; ++ /** Next frame num to setup next ISOC transfer */ ++ uint32_t frame_num; ++ /** Indicates SOF number overrun in DSTS */ ++ uint8_t frm_overrun; ++ ++#ifdef DWC_UTE_PER_IO ++ /** Next frame num for which will be setup DMA Desc */ ++ uint32_t xiso_frame_num; ++ /** bInterval */ ++ uint32_t xiso_bInterval; ++ /** Count of currently active transfers - shall be either 0 or 1 */ ++ int xiso_active_xfers; ++ int xiso_queued_xfers; ++#endif ++#ifdef DWC_EN_ISOC ++ /** ++ * Variables specific for ISOC EPs ++ * ++ */ ++ /** DMA addresses of ISOC buffers */ ++ dwc_dma_t dma_addr0; ++ dwc_dma_t dma_addr1; ++ ++ dwc_dma_t iso_dma_desc_addr; ++ dwc_otg_dev_dma_desc_t *iso_desc_addr; ++ ++ /** pointer to the transfer buffers */ ++ uint8_t *xfer_buff0; ++ uint8_t *xfer_buff1; ++ ++ /** number of ISOC Buffer is processing */ ++ uint32_t proc_buf_num; ++ /** Interval of ISOC Buffer processing */ ++ uint32_t buf_proc_intrvl; ++ /** Data size for regular frame */ ++ uint32_t data_per_frame; ++ ++ /* todo - pattern data support is to be implemented in the future */ ++ /** Data size for pattern frame */ ++ uint32_t data_pattern_frame; ++ /** Frame number of pattern data */ ++ uint32_t sync_frame; ++ ++ /** bInterval */ ++ uint32_t bInterval; ++ /** ISO Packet number per frame */ ++ uint32_t pkt_per_frm; ++ /** Next frame num for which will be setup DMA Desc */ ++ uint32_t next_frame; ++ /** Number of packets per buffer processing */ ++ uint32_t pkt_cnt; ++ /** Info for all isoc packets */ ++ iso_pkt_info_t *pkt_info; ++ /** current pkt number */ ++ uint32_t cur_pkt; ++ /** current pkt number */ ++ uint8_t *cur_pkt_addr; ++ /** current pkt number */ ++ uint32_t cur_pkt_dma_addr; ++#endif /* DWC_EN_ISOC */ ++ ++/** @} */ ++} dwc_ep_t; ++ ++/* ++ * Reasons for halting a host channel. ++ */ ++typedef enum dwc_otg_halt_status { ++ DWC_OTG_HC_XFER_NO_HALT_STATUS, ++ DWC_OTG_HC_XFER_COMPLETE, ++ DWC_OTG_HC_XFER_URB_COMPLETE, ++ DWC_OTG_HC_XFER_ACK, ++ DWC_OTG_HC_XFER_NAK, ++ DWC_OTG_HC_XFER_NYET, ++ DWC_OTG_HC_XFER_STALL, ++ DWC_OTG_HC_XFER_XACT_ERR, ++ DWC_OTG_HC_XFER_FRAME_OVERRUN, ++ DWC_OTG_HC_XFER_BABBLE_ERR, ++ DWC_OTG_HC_XFER_DATA_TOGGLE_ERR, ++ DWC_OTG_HC_XFER_AHB_ERR, ++ DWC_OTG_HC_XFER_PERIODIC_INCOMPLETE, ++ DWC_OTG_HC_XFER_URB_DEQUEUE ++} dwc_otg_halt_status_e; ++ ++/** ++ * Host channel descriptor. This structure represents the state of a single ++ * host channel when acting in host mode. It contains the data items needed to ++ * transfer packets to an endpoint via a host channel. ++ */ ++typedef struct dwc_hc { ++ /** Host channel number used for register address lookup */ ++ uint8_t hc_num; ++ ++ /** Device to access */ ++ unsigned dev_addr:7; ++ ++ /** EP to access */ ++ unsigned ep_num:4; ++ ++ /** EP direction. 0: OUT, 1: IN */ ++ unsigned ep_is_in:1; ++ ++ /** ++ * EP speed. ++ * One of the following values: ++ * - DWC_OTG_EP_SPEED_LOW ++ * - DWC_OTG_EP_SPEED_FULL ++ * - DWC_OTG_EP_SPEED_HIGH ++ */ ++ unsigned speed:2; ++#define DWC_OTG_EP_SPEED_LOW 0 ++#define DWC_OTG_EP_SPEED_FULL 1 ++#define DWC_OTG_EP_SPEED_HIGH 2 ++ ++ /** ++ * Endpoint type. ++ * One of the following values: ++ * - DWC_OTG_EP_TYPE_CONTROL: 0 ++ * - DWC_OTG_EP_TYPE_ISOC: 1 ++ * - DWC_OTG_EP_TYPE_BULK: 2 ++ * - DWC_OTG_EP_TYPE_INTR: 3 ++ */ ++ unsigned ep_type:2; ++ ++ /** Max packet size in bytes */ ++ unsigned max_packet:11; ++ ++ /** ++ * PID for initial transaction. ++ * 0: DATA0,
++ * 1: DATA2,
++ * 2: DATA1,
++ * 3: MDATA (non-Control EP), ++ * SETUP (Control EP) ++ */ ++ unsigned data_pid_start:2; ++#define DWC_OTG_HC_PID_DATA0 0 ++#define DWC_OTG_HC_PID_DATA2 1 ++#define DWC_OTG_HC_PID_DATA1 2 ++#define DWC_OTG_HC_PID_MDATA 3 ++#define DWC_OTG_HC_PID_SETUP 3 ++ ++ /** Number of periodic transactions per (micro)frame */ ++ unsigned multi_count:2; ++ ++ /** @name Transfer State */ ++ /** @{ */ ++ ++ /** Pointer to the current transfer buffer position. */ ++ uint8_t *xfer_buff; ++ /** ++ * In Buffer DMA mode this buffer will be used ++ * if xfer_buff is not DWORD aligned. ++ */ ++ dwc_dma_t align_buff; ++ /** Total number of bytes to transfer. */ ++ uint32_t xfer_len; ++ /** Number of bytes transferred so far. */ ++ uint32_t xfer_count; ++ /** Packet count at start of transfer.*/ ++ uint16_t start_pkt_count; ++ ++ /** ++ * Flag to indicate whether the transfer has been started. Set to 1 if ++ * it has been started, 0 otherwise. ++ */ ++ uint8_t xfer_started; ++ ++ /** ++ * Set to 1 to indicate that a PING request should be issued on this ++ * channel. If 0, process normally. ++ */ ++ uint8_t do_ping; ++ ++ /** ++ * Set to 1 to indicate that the error count for this transaction is ++ * non-zero. Set to 0 if the error count is 0. ++ */ ++ uint8_t error_state; ++ ++ /** ++ * Set to 1 to indicate that this channel should be halted the next ++ * time a request is queued for the channel. This is necessary in ++ * slave mode if no request queue space is available when an attempt ++ * is made to halt the channel. ++ */ ++ uint8_t halt_on_queue; ++ ++ /** ++ * Set to 1 if the host channel has been halted, but the core is not ++ * finished flushing queued requests. Otherwise 0. ++ */ ++ uint8_t halt_pending; ++ ++ /** ++ * Reason for halting the host channel. ++ */ ++ dwc_otg_halt_status_e halt_status; ++ ++ /* ++ * Split settings for the host channel ++ */ ++ uint8_t do_split; /**< Enable split for the channel */ ++ uint8_t complete_split; /**< Enable complete split */ ++ uint8_t hub_addr; /**< Address of high speed hub */ ++ ++ uint8_t port_addr; /**< Port of the low/full speed device */ ++ /** Split transaction position ++ * One of the following values: ++ * - DWC_HCSPLIT_XACTPOS_MID ++ * - DWC_HCSPLIT_XACTPOS_BEGIN ++ * - DWC_HCSPLIT_XACTPOS_END ++ * - DWC_HCSPLIT_XACTPOS_ALL */ ++ uint8_t xact_pos; ++ ++ /** Set when the host channel does a short read. */ ++ uint8_t short_read; ++ ++ /** ++ * Number of requests issued for this channel since it was assigned to ++ * the current transfer (not counting PINGs). ++ */ ++ uint8_t requests; ++ ++ /** ++ * Queue Head for the transfer being processed by this channel. ++ */ ++ struct dwc_otg_qh *qh; ++ ++ /** @} */ ++ ++ /** Entry in list of host channels. */ ++ DWC_CIRCLEQ_ENTRY(dwc_hc) hc_list_entry; ++ ++ /** @name Descriptor DMA support */ ++ /** @{ */ ++ ++ /** Number of Transfer Descriptors */ ++ uint16_t ntd; ++ ++ /** Descriptor List DMA address */ ++ dwc_dma_t desc_list_addr; ++ ++ /** Scheduling micro-frame bitmap. */ ++ uint8_t schinfo; ++ ++ /** @} */ ++} dwc_hc_t; ++ ++/** ++ * The following parameters may be specified when starting the module. These ++ * parameters define how the DWC_otg controller should be configured. ++ */ ++typedef struct dwc_otg_core_params { ++ int32_t opt; ++ ++ /** ++ * Specifies the OTG capabilities. The driver will automatically ++ * detect the value for this parameter if none is specified. ++ * 0 - HNP and SRP capable (default) ++ * 1 - SRP Only capable ++ * 2 - No HNP/SRP capable ++ */ ++ int32_t otg_cap; ++ ++ /** ++ * Specifies whether to use slave or DMA mode for accessing the data ++ * FIFOs. The driver will automatically detect the value for this ++ * parameter if none is specified. ++ * 0 - Slave ++ * 1 - DMA (default, if available) ++ */ ++ int32_t dma_enable; ++ ++ /** ++ * When DMA mode is enabled specifies whether to use address DMA or DMA ++ * Descriptor mode for accessing the data FIFOs in device mode. The driver ++ * will automatically detect the value for this if none is specified. ++ * 0 - address DMA ++ * 1 - DMA Descriptor(default, if available) ++ */ ++ int32_t dma_desc_enable; ++ /** The DMA Burst size (applicable only for External DMA ++ * Mode). 1, 4, 8 16, 32, 64, 128, 256 (default 32) ++ */ ++ int32_t dma_burst_size; /* Translate this to GAHBCFG values */ ++ ++ /** ++ * Specifies the maximum speed of operation in host and device mode. ++ * The actual speed depends on the speed of the attached device and ++ * the value of phy_type. The actual speed depends on the speed of the ++ * attached device. ++ * 0 - High Speed (default) ++ * 1 - Full Speed ++ */ ++ int32_t speed; ++ /** Specifies whether low power mode is supported when attached ++ * to a Full Speed or Low Speed device in host mode. ++ * 0 - Don't support low power mode (default) ++ * 1 - Support low power mode ++ */ ++ int32_t host_support_fs_ls_low_power; ++ ++ /** Specifies the PHY clock rate in low power mode when connected to a ++ * Low Speed device in host mode. This parameter is applicable only if ++ * HOST_SUPPORT_FS_LS_LOW_POWER is enabled. If PHY_TYPE is set to FS ++ * then defaults to 6 MHZ otherwise 48 MHZ. ++ * ++ * 0 - 48 MHz ++ * 1 - 6 MHz ++ */ ++ int32_t host_ls_low_power_phy_clk; ++ ++ /** ++ * 0 - Use cC FIFO size parameters ++ * 1 - Allow dynamic FIFO sizing (default) ++ */ ++ int32_t enable_dynamic_fifo; ++ ++ /** Total number of 4-byte words in the data FIFO memory. This ++ * memory includes the Rx FIFO, non-periodic Tx FIFO, and periodic ++ * Tx FIFOs. ++ * 32 to 32768 (default 8192) ++ * Note: The total FIFO memory depth in the FPGA configuration is 8192. ++ */ ++ int32_t data_fifo_size; ++ ++ /** Number of 4-byte words in the Rx FIFO in device mode when dynamic ++ * FIFO sizing is enabled. ++ * 16 to 32768 (default 1064) ++ */ ++ int32_t dev_rx_fifo_size; ++ ++ /** Number of 4-byte words in the non-periodic Tx FIFO in device mode ++ * when dynamic FIFO sizing is enabled. ++ * 16 to 32768 (default 1024) ++ */ ++ int32_t dev_nperio_tx_fifo_size; ++ ++ /** Number of 4-byte words in each of the periodic Tx FIFOs in device ++ * mode when dynamic FIFO sizing is enabled. ++ * 4 to 768 (default 256) ++ */ ++ uint32_t dev_perio_tx_fifo_size[MAX_PERIO_FIFOS]; ++ ++ /** Number of 4-byte words in the Rx FIFO in host mode when dynamic ++ * FIFO sizing is enabled. ++ * 16 to 32768 (default 1024) ++ */ ++ int32_t host_rx_fifo_size; ++ ++ /** Number of 4-byte words in the non-periodic Tx FIFO in host mode ++ * when Dynamic FIFO sizing is enabled in the core. ++ * 16 to 32768 (default 1024) ++ */ ++ int32_t host_nperio_tx_fifo_size; ++ ++ /** Number of 4-byte words in the host periodic Tx FIFO when dynamic ++ * FIFO sizing is enabled. ++ * 16 to 32768 (default 1024) ++ */ ++ int32_t host_perio_tx_fifo_size; ++ ++ /** The maximum transfer size supported in bytes. ++ * 2047 to 65,535 (default 65,535) ++ */ ++ int32_t max_transfer_size; ++ ++ /** The maximum number of packets in a transfer. ++ * 15 to 511 (default 511) ++ */ ++ int32_t max_packet_count; ++ ++ /** The number of host channel registers to use. ++ * 1 to 16 (default 12) ++ * Note: The FPGA configuration supports a maximum of 12 host channels. ++ */ ++ int32_t host_channels; ++ ++ /** The number of endpoints in addition to EP0 available for device ++ * mode operations. ++ * 1 to 15 (default 6 IN and OUT) ++ * Note: The FPGA configuration supports a maximum of 6 IN and OUT ++ * endpoints in addition to EP0. ++ */ ++ int32_t dev_endpoints; ++ ++ /** ++ * Specifies the type of PHY interface to use. By default, the driver ++ * will automatically detect the phy_type. ++ * ++ * 0 - Full Speed PHY ++ * 1 - UTMI+ (default) ++ * 2 - ULPI ++ */ ++ int32_t phy_type; ++ ++ /** ++ * Specifies the UTMI+ Data Width. This parameter is ++ * applicable for a PHY_TYPE of UTMI+ or ULPI. (For a ULPI ++ * PHY_TYPE, this parameter indicates the data width between ++ * the MAC and the ULPI Wrapper.) Also, this parameter is ++ * applicable only if the OTG_HSPHY_WIDTH cC parameter was set ++ * to "8 and 16 bits", meaning that the core has been ++ * configured to work at either data path width. ++ * ++ * 8 or 16 bits (default 16) ++ */ ++ int32_t phy_utmi_width; ++ ++ /** ++ * Specifies whether the ULPI operates at double or single ++ * data rate. This parameter is only applicable if PHY_TYPE is ++ * ULPI. ++ * ++ * 0 - single data rate ULPI interface with 8 bit wide data ++ * bus (default) ++ * 1 - double data rate ULPI interface with 4 bit wide data ++ * bus ++ */ ++ int32_t phy_ulpi_ddr; ++ ++ /** ++ * Specifies whether to use the internal or external supply to ++ * drive the vbus with a ULPI phy. ++ */ ++ int32_t phy_ulpi_ext_vbus; ++ ++ /** ++ * Specifies whether to use the I2Cinterface for full speed PHY. This ++ * parameter is only applicable if PHY_TYPE is FS. ++ * 0 - No (default) ++ * 1 - Yes ++ */ ++ int32_t i2c_enable; ++ ++ int32_t ulpi_fs_ls; ++ ++ int32_t ts_dline; ++ ++ /** ++ * Specifies whether dedicated transmit FIFOs are ++ * enabled for non periodic IN endpoints in device mode ++ * 0 - No ++ * 1 - Yes ++ */ ++ int32_t en_multiple_tx_fifo; ++ ++ /** Number of 4-byte words in each of the Tx FIFOs in device ++ * mode when dynamic FIFO sizing is enabled. ++ * 4 to 768 (default 256) ++ */ ++ uint32_t dev_tx_fifo_size[MAX_TX_FIFOS]; ++ ++ /** Thresholding enable flag- ++ * bit 0 - enable non-ISO Tx thresholding ++ * bit 1 - enable ISO Tx thresholding ++ * bit 2 - enable Rx thresholding ++ */ ++ uint32_t thr_ctl; ++ ++ /** Thresholding length for Tx ++ * FIFOs in 32 bit DWORDs ++ */ ++ uint32_t tx_thr_length; ++ ++ /** Thresholding length for Rx ++ * FIFOs in 32 bit DWORDs ++ */ ++ uint32_t rx_thr_length; ++ ++ /** ++ * Specifies whether LPM (Link Power Management) support is enabled ++ */ ++ int32_t lpm_enable; ++ ++ /** Per Transfer Interrupt ++ * mode enable flag ++ * 1 - Enabled ++ * 0 - Disabled ++ */ ++ int32_t pti_enable; ++ ++ /** Multi Processor Interrupt ++ * mode enable flag ++ * 1 - Enabled ++ * 0 - Disabled ++ */ ++ int32_t mpi_enable; ++ ++ /** IS_USB Capability ++ * 1 - Enabled ++ * 0 - Disabled ++ */ ++ int32_t ic_usb_cap; ++ ++ /** AHB Threshold Ratio ++ * 2'b00 AHB Threshold = MAC Threshold ++ * 2'b01 AHB Threshold = 1/2 MAC Threshold ++ * 2'b10 AHB Threshold = 1/4 MAC Threshold ++ * 2'b11 AHB Threshold = 1/8 MAC Threshold ++ */ ++ int32_t ahb_thr_ratio; ++ ++ /** ADP Support ++ * 1 - Enabled ++ * 0 - Disabled ++ */ ++ int32_t adp_supp_enable; ++ ++ /** HFIR Reload Control ++ * 0 - The HFIR cannot be reloaded dynamically. ++ * 1 - Allow dynamic reloading of the HFIR register during runtime. ++ */ ++ int32_t reload_ctl; ++ ++ /** DCFG: Enable device Out NAK ++ * 0 - The core does not set NAK after Bulk Out transfer complete. ++ * 1 - The core sets NAK after Bulk OUT transfer complete. ++ */ ++ int32_t dev_out_nak; ++ ++ /** DCFG: Enable Continue on BNA ++ * After receiving BNA interrupt the core disables the endpoint,when the ++ * endpoint is re-enabled by the application the core starts processing ++ * 0 - from the DOEPDMA descriptor ++ * 1 - from the descriptor which received the BNA. ++ */ ++ int32_t cont_on_bna; ++ ++ /** GAHBCFG: AHB Single Support ++ * This bit when programmed supports SINGLE transfers for remainder ++ * data in a transfer for DMA mode of operation. ++ * 0 - in this case the remainder data will be sent using INCR burst size. ++ * 1 - in this case the remainder data will be sent using SINGLE burst size. ++ */ ++ int32_t ahb_single; ++ ++ /** Core Power down mode ++ * 0 - No Power Down is enabled ++ * 1 - Reserved ++ * 2 - Complete Power Down (Hibernation) ++ */ ++ int32_t power_down; ++ ++ /** OTG revision supported ++ * 0 - OTG 1.3 revision ++ * 1 - OTG 2.0 revision ++ */ ++ int32_t otg_ver; ++ ++} dwc_otg_core_params_t; ++ ++#ifdef DEBUG ++struct dwc_otg_core_if; ++typedef struct hc_xfer_info { ++ struct dwc_otg_core_if *core_if; ++ dwc_hc_t *hc; ++} hc_xfer_info_t; ++#endif ++ ++typedef struct ep_xfer_info { ++ struct dwc_otg_core_if *core_if; ++ dwc_ep_t *ep; ++ uint8_t state; ++} ep_xfer_info_t; ++/* ++ * Device States ++ */ ++typedef enum dwc_otg_lx_state { ++ /** On state */ ++ DWC_OTG_L0, ++ /** LPM sleep state*/ ++ DWC_OTG_L1, ++ /** USB suspend state*/ ++ DWC_OTG_L2, ++ /** Off state*/ ++ DWC_OTG_L3 ++} dwc_otg_lx_state_e; ++ ++struct dwc_otg_global_regs_backup { ++ uint32_t gotgctl_local; ++ uint32_t gintmsk_local; ++ uint32_t gahbcfg_local; ++ uint32_t gusbcfg_local; ++ uint32_t grxfsiz_local; ++ uint32_t gnptxfsiz_local; ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ uint32_t glpmcfg_local; ++#endif ++ uint32_t gi2cctl_local; ++ uint32_t hptxfsiz_local; ++ uint32_t pcgcctl_local; ++ uint32_t gdfifocfg_local; ++ uint32_t dtxfsiz_local[MAX_EPS_CHANNELS]; ++ uint32_t gpwrdn_local; ++ uint32_t xhib_pcgcctl; ++ uint32_t xhib_gpwrdn; ++}; ++ ++struct dwc_otg_host_regs_backup { ++ uint32_t hcfg_local; ++ uint32_t haintmsk_local; ++ uint32_t hcintmsk_local[MAX_EPS_CHANNELS]; ++ uint32_t hprt0_local; ++ uint32_t hfir_local; ++}; ++ ++struct dwc_otg_dev_regs_backup { ++ uint32_t dcfg; ++ uint32_t dctl; ++ uint32_t daintmsk; ++ uint32_t diepmsk; ++ uint32_t doepmsk; ++ uint32_t diepctl[MAX_EPS_CHANNELS]; ++ uint32_t dieptsiz[MAX_EPS_CHANNELS]; ++ uint32_t diepdma[MAX_EPS_CHANNELS]; ++}; ++/** ++ * The dwc_otg_core_if structure contains information needed to manage ++ * the DWC_otg controller acting in either host or device mode. It ++ * represents the programming view of the controller as a whole. ++ */ ++struct dwc_otg_core_if { ++ /** Parameters that define how the core should be configured.*/ ++ dwc_otg_core_params_t *core_params; ++ ++ /** Core Global registers starting at offset 000h. */ ++ dwc_otg_core_global_regs_t *core_global_regs; ++ ++ /** Device-specific information */ ++ dwc_otg_dev_if_t *dev_if; ++ /** Host-specific information */ ++ dwc_otg_host_if_t *host_if; ++ ++ /** Value from SNPSID register */ ++ uint32_t snpsid; ++ ++ /* ++ * Set to 1 if the core PHY interface bits in USBCFG have been ++ * initialized. ++ */ ++ uint8_t phy_init_done; ++ ++ /* ++ * SRP Success flag, set by srp success interrupt in FS I2C mode ++ */ ++ uint8_t srp_success; ++ uint8_t srp_timer_started; ++ /** Timer for SRP. If it expires before SRP is successful ++ * clear the SRP. */ ++ dwc_timer_t *srp_timer; ++ ++#ifdef DWC_DEV_SRPCAP ++ /* This timer is needed to power on the hibernated host core if SRP is not ++ * initiated on connected SRP capable device for limited period of time ++ */ ++ uint8_t pwron_timer_started; ++ dwc_timer_t *pwron_timer; ++#endif ++ /* Common configuration information */ ++ /** Power and Clock Gating Control Register */ ++ volatile uint32_t *pcgcctl; ++#define DWC_OTG_PCGCCTL_OFFSET 0xE00 ++ ++ /** Push/pop addresses for endpoints or host channels.*/ ++ uint32_t *data_fifo[MAX_EPS_CHANNELS]; ++#define DWC_OTG_DATA_FIFO_OFFSET 0x1000 ++#define DWC_OTG_DATA_FIFO_SIZE 0x1000 ++ ++ /** Total RAM for FIFOs (Bytes) */ ++ uint16_t total_fifo_size; ++ /** Size of Rx FIFO (Bytes) */ ++ uint16_t rx_fifo_size; ++ /** Size of Non-periodic Tx FIFO (Bytes) */ ++ uint16_t nperio_tx_fifo_size; ++ ++ /** 1 if DMA is enabled, 0 otherwise. */ ++ uint8_t dma_enable; ++ ++ /** 1 if DMA descriptor is enabled, 0 otherwise. */ ++ uint8_t dma_desc_enable; ++ ++ /** 1 if PTI Enhancement mode is enabled, 0 otherwise. */ ++ uint8_t pti_enh_enable; ++ ++ /** 1 if MPI Enhancement mode is enabled, 0 otherwise. */ ++ uint8_t multiproc_int_enable; ++ ++ /** 1 if dedicated Tx FIFOs are enabled, 0 otherwise. */ ++ uint8_t en_multiple_tx_fifo; ++ ++ /** Set to 1 if multiple packets of a high-bandwidth transfer is in ++ * process of being queued */ ++ uint8_t queuing_high_bandwidth; ++ ++ /** Hardware Configuration -- stored here for convenience.*/ ++ hwcfg1_data_t hwcfg1; ++ hwcfg2_data_t hwcfg2; ++ hwcfg3_data_t hwcfg3; ++ hwcfg4_data_t hwcfg4; ++ fifosize_data_t hptxfsiz; ++ ++ /** Host and Device Configuration -- stored here for convenience.*/ ++ hcfg_data_t hcfg; ++ dcfg_data_t dcfg; ++ ++ /** The operational State, during transations ++ * (a_host>>a_peripherial and b_device=>b_host) this may not ++ * match the core but allows the software to determine ++ * transitions. ++ */ ++ uint8_t op_state; ++ ++ /** ++ * Set to 1 if the HCD needs to be restarted on a session request ++ * interrupt. This is required if no connector ID status change has ++ * occurred since the HCD was last disconnected. ++ */ ++ uint8_t restart_hcd_on_session_req; ++ ++ /** HCD callbacks */ ++ /** A-Device is a_host */ ++#define A_HOST (1) ++ /** A-Device is a_suspend */ ++#define A_SUSPEND (2) ++ /** A-Device is a_peripherial */ ++#define A_PERIPHERAL (3) ++ /** B-Device is operating as a Peripheral. */ ++#define B_PERIPHERAL (4) ++ /** B-Device is operating as a Host. */ ++#define B_HOST (5) ++ ++ /** HCD callbacks */ ++ struct dwc_otg_cil_callbacks *hcd_cb; ++ /** PCD callbacks */ ++ struct dwc_otg_cil_callbacks *pcd_cb; ++ ++ /** Device mode Periodic Tx FIFO Mask */ ++ uint32_t p_tx_msk; ++ /** Device mode Periodic Tx FIFO Mask */ ++ uint32_t tx_msk; ++ ++ /** Workqueue object used for handling several interrupts */ ++ dwc_workq_t *wq_otg; ++ ++ /** Timer object used for handling "Wakeup Detected" Interrupt */ ++ dwc_timer_t *wkp_timer; ++ /** This arrays used for debug purposes for DEV OUT NAK enhancement */ ++ uint32_t start_doeptsiz_val[MAX_EPS_CHANNELS]; ++ ep_xfer_info_t ep_xfer_info[MAX_EPS_CHANNELS]; ++ dwc_timer_t *ep_xfer_timer[MAX_EPS_CHANNELS]; ++#ifdef DEBUG ++ uint32_t start_hcchar_val[MAX_EPS_CHANNELS]; ++ ++ hc_xfer_info_t hc_xfer_info[MAX_EPS_CHANNELS]; ++ dwc_timer_t *hc_xfer_timer[MAX_EPS_CHANNELS]; ++ ++ uint32_t hfnum_7_samples; ++ uint64_t hfnum_7_frrem_accum; ++ uint32_t hfnum_0_samples; ++ uint64_t hfnum_0_frrem_accum; ++ uint32_t hfnum_other_samples; ++ uint64_t hfnum_other_frrem_accum; ++#endif ++ ++#ifdef DWC_UTE_CFI ++ uint16_t pwron_rxfsiz; ++ uint16_t pwron_gnptxfsiz; ++ uint16_t pwron_txfsiz[15]; ++ ++ uint16_t init_rxfsiz; ++ uint16_t init_gnptxfsiz; ++ uint16_t init_txfsiz[15]; ++#endif ++ ++ /** Lx state of device */ ++ dwc_otg_lx_state_e lx_state; ++ ++ /** Saved Core Global registers */ ++ struct dwc_otg_global_regs_backup *gr_backup; ++ /** Saved Host registers */ ++ struct dwc_otg_host_regs_backup *hr_backup; ++ /** Saved Device registers */ ++ struct dwc_otg_dev_regs_backup *dr_backup; ++ ++ /** Power Down Enable */ ++ uint32_t power_down; ++ ++ /** ADP support Enable */ ++ uint32_t adp_enable; ++ ++ /** ADP structure object */ ++ dwc_otg_adp_t adp; ++ ++ /** hibernation/suspend flag */ ++ int hibernation_suspend; ++ ++ /** Device mode extended hibernation flag */ ++ int xhib; ++ ++ /** OTG revision supported */ ++ uint32_t otg_ver; ++ ++ /** OTG status flag used for HNP polling */ ++ uint8_t otg_sts; ++ ++ /** Pointer to either hcd->lock or pcd->lock */ ++ dwc_spinlock_t *lock; ++ ++ /** Start predict NextEP based on Learning Queue if equal 1, ++ * also used as counter of disabled NP IN EP's */ ++ uint8_t start_predict; ++ ++ /** NextEp sequence, including EP0: nextep_seq[] = EP if non-periodic and ++ * active, 0xff otherwise */ ++ uint8_t nextep_seq[MAX_EPS_CHANNELS]; ++ ++ /** Index of fisrt EP in nextep_seq array which should be re-enabled **/ ++ uint8_t first_in_nextep_seq; ++ ++ /** Frame number while entering to ISR - needed for ISOCs **/ ++ uint32_t frame_num; ++ ++}; ++ ++#ifdef DEBUG ++/* ++ * This function is called when transfer is timed out. ++ */ ++extern void hc_xfer_timeout(void *ptr); ++#endif ++ ++/* ++ * This function is called when transfer is timed out on endpoint. ++ */ ++extern void ep_xfer_timeout(void *ptr); ++ ++/* ++ * The following functions are functions for works ++ * using during handling some interrupts ++ */ ++extern void w_conn_id_status_change(void *p); ++ ++extern void w_wakeup_detected(void *p); ++ ++/** Saves global register values into system memory. */ ++extern int dwc_otg_save_global_regs(dwc_otg_core_if_t * core_if); ++/** Saves device register values into system memory. */ ++extern int dwc_otg_save_dev_regs(dwc_otg_core_if_t * core_if); ++/** Saves host register values into system memory. */ ++extern int dwc_otg_save_host_regs(dwc_otg_core_if_t * core_if); ++/** Restore global register values. */ ++extern int dwc_otg_restore_global_regs(dwc_otg_core_if_t * core_if); ++/** Restore host register values. */ ++extern int dwc_otg_restore_host_regs(dwc_otg_core_if_t * core_if, int reset); ++/** Restore device register values. */ ++extern int dwc_otg_restore_dev_regs(dwc_otg_core_if_t * core_if, ++ int rem_wakeup); ++extern int restore_lpm_i2c_regs(dwc_otg_core_if_t * core_if); ++extern int restore_essential_regs(dwc_otg_core_if_t * core_if, int rmode, ++ int is_host); ++ ++extern int dwc_otg_host_hibernation_restore(dwc_otg_core_if_t * core_if, ++ int restore_mode, int reset); ++extern int dwc_otg_device_hibernation_restore(dwc_otg_core_if_t * core_if, ++ int rem_wakeup, int reset); ++ ++/* ++ * The following functions support initialization of the CIL driver component ++ * and the DWC_otg controller. ++ */ ++extern void dwc_otg_core_host_init(dwc_otg_core_if_t * _core_if); ++extern void dwc_otg_core_dev_init(dwc_otg_core_if_t * _core_if); ++ ++/** @name Device CIL Functions ++ * The following functions support managing the DWC_otg controller in device ++ * mode. ++ */ ++/**@{*/ ++extern void dwc_otg_wakeup(dwc_otg_core_if_t * _core_if); ++extern void dwc_otg_read_setup_packet(dwc_otg_core_if_t * _core_if, ++ uint32_t * _dest); ++extern uint32_t dwc_otg_get_frame_number(dwc_otg_core_if_t * _core_if); ++extern void dwc_otg_ep0_activate(dwc_otg_core_if_t * _core_if, dwc_ep_t * _ep); ++extern void dwc_otg_ep_activate(dwc_otg_core_if_t * _core_if, dwc_ep_t * _ep); ++extern void dwc_otg_ep_deactivate(dwc_otg_core_if_t * _core_if, dwc_ep_t * _ep); ++extern void dwc_otg_ep_start_transfer(dwc_otg_core_if_t * _core_if, ++ dwc_ep_t * _ep); ++extern void dwc_otg_ep_start_zl_transfer(dwc_otg_core_if_t * _core_if, ++ dwc_ep_t * _ep); ++extern void dwc_otg_ep0_start_transfer(dwc_otg_core_if_t * _core_if, ++ dwc_ep_t * _ep); ++extern void dwc_otg_ep0_continue_transfer(dwc_otg_core_if_t * _core_if, ++ dwc_ep_t * _ep); ++extern void dwc_otg_ep_write_packet(dwc_otg_core_if_t * _core_if, ++ dwc_ep_t * _ep, int _dma); ++extern void dwc_otg_ep_set_stall(dwc_otg_core_if_t * _core_if, dwc_ep_t * _ep); ++extern void dwc_otg_ep_clear_stall(dwc_otg_core_if_t * _core_if, ++ dwc_ep_t * _ep); ++extern void dwc_otg_enable_device_interrupts(dwc_otg_core_if_t * _core_if); ++ ++#ifdef DWC_EN_ISOC ++extern void dwc_otg_iso_ep_start_frm_transfer(dwc_otg_core_if_t * core_if, ++ dwc_ep_t * ep); ++extern void dwc_otg_iso_ep_start_buf_transfer(dwc_otg_core_if_t * core_if, ++ dwc_ep_t * ep); ++#endif /* DWC_EN_ISOC */ ++/**@}*/ ++ ++/** @name Host CIL Functions ++ * The following functions support managing the DWC_otg controller in host ++ * mode. ++ */ ++/**@{*/ ++extern void dwc_otg_hc_init(dwc_otg_core_if_t * _core_if, dwc_hc_t * _hc); ++extern void dwc_otg_hc_halt(dwc_otg_core_if_t * _core_if, ++ dwc_hc_t * _hc, dwc_otg_halt_status_e _halt_status); ++extern void dwc_otg_hc_cleanup(dwc_otg_core_if_t * _core_if, dwc_hc_t * _hc); ++extern void dwc_otg_hc_start_transfer(dwc_otg_core_if_t * _core_if, ++ dwc_hc_t * _hc); ++extern int dwc_otg_hc_continue_transfer(dwc_otg_core_if_t * _core_if, ++ dwc_hc_t * _hc); ++extern void dwc_otg_hc_do_ping(dwc_otg_core_if_t * _core_if, dwc_hc_t * _hc); ++extern void dwc_otg_hc_write_packet(dwc_otg_core_if_t * _core_if, ++ dwc_hc_t * _hc); ++extern void dwc_otg_enable_host_interrupts(dwc_otg_core_if_t * _core_if); ++extern void dwc_otg_disable_host_interrupts(dwc_otg_core_if_t * _core_if); ++ ++extern void dwc_otg_hc_start_transfer_ddma(dwc_otg_core_if_t * core_if, ++ dwc_hc_t * hc); ++ ++extern uint32_t calc_frame_interval(dwc_otg_core_if_t * core_if); ++ ++/* Macro used to clear one channel interrupt */ ++#define clear_hc_int(_hc_regs_, _intr_) \ ++do { \ ++ hcint_data_t hcint_clear = {.d32 = 0}; \ ++ hcint_clear.b._intr_ = 1; \ ++ DWC_WRITE_REG32(&(_hc_regs_)->hcint, hcint_clear.d32); \ ++} while (0) ++ ++/* ++ * Macro used to disable one channel interrupt. Channel interrupts are ++ * disabled when the channel is halted or released by the interrupt handler. ++ * There is no need to handle further interrupts of that type until the ++ * channel is re-assigned. In fact, subsequent handling may cause crashes ++ * because the channel structures are cleaned up when the channel is released. ++ */ ++#define disable_hc_int(_hc_regs_, _intr_) \ ++do { \ ++ hcintmsk_data_t hcintmsk = {.d32 = 0}; \ ++ hcintmsk.b._intr_ = 1; \ ++ DWC_MODIFY_REG32(&(_hc_regs_)->hcintmsk, hcintmsk.d32, 0); \ ++} while (0) ++ ++/** ++ * This function Reads HPRT0 in preparation to modify. It keeps the ++ * WC bits 0 so that if they are read as 1, they won't clear when you ++ * write it back ++ */ ++static inline uint32_t dwc_otg_read_hprt0(dwc_otg_core_if_t * _core_if) ++{ ++ hprt0_data_t hprt0; ++ hprt0.d32 = DWC_READ_REG32(_core_if->host_if->hprt0); ++ hprt0.b.prtena = 0; ++ hprt0.b.prtconndet = 0; ++ hprt0.b.prtenchng = 0; ++ hprt0.b.prtovrcurrchng = 0; ++ return hprt0.d32; ++} ++ ++/**@}*/ ++ ++/** @name Common CIL Functions ++ * The following functions support managing the DWC_otg controller in either ++ * device or host mode. ++ */ ++/**@{*/ ++ ++extern void dwc_otg_read_packet(dwc_otg_core_if_t * core_if, ++ uint8_t * dest, uint16_t bytes); ++ ++extern void dwc_otg_flush_tx_fifo(dwc_otg_core_if_t * _core_if, const int _num); ++extern void dwc_otg_flush_rx_fifo(dwc_otg_core_if_t * _core_if); ++extern void dwc_otg_core_reset(dwc_otg_core_if_t * _core_if); ++ ++/** ++ * This function returns the Core Interrupt register. ++ */ ++static inline uint32_t dwc_otg_read_core_intr(dwc_otg_core_if_t * core_if) ++{ ++ return (DWC_READ_REG32(&core_if->core_global_regs->gintsts) & ++ DWC_READ_REG32(&core_if->core_global_regs->gintmsk)); ++} ++ ++/** ++ * This function returns the OTG Interrupt register. ++ */ ++static inline uint32_t dwc_otg_read_otg_intr(dwc_otg_core_if_t * core_if) ++{ ++ return (DWC_READ_REG32(&core_if->core_global_regs->gotgint)); ++} ++ ++/** ++ * This function reads the Device All Endpoints Interrupt register and ++ * returns the IN endpoint interrupt bits. ++ */ ++static inline uint32_t dwc_otg_read_dev_all_in_ep_intr(dwc_otg_core_if_t * ++ core_if) ++{ ++ ++ uint32_t v; ++ ++ if (core_if->multiproc_int_enable) { ++ v = DWC_READ_REG32(&core_if->dev_if-> ++ dev_global_regs->deachint) & ++ DWC_READ_REG32(&core_if-> ++ dev_if->dev_global_regs->deachintmsk); ++ } else { ++ v = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->daint) & ++ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->daintmsk); ++ } ++ return (v & 0xffff); ++} ++ ++/** ++ * This function reads the Device All Endpoints Interrupt register and ++ * returns the OUT endpoint interrupt bits. ++ */ ++static inline uint32_t dwc_otg_read_dev_all_out_ep_intr(dwc_otg_core_if_t * ++ core_if) ++{ ++ uint32_t v; ++ ++ if (core_if->multiproc_int_enable) { ++ v = DWC_READ_REG32(&core_if->dev_if-> ++ dev_global_regs->deachint) & ++ DWC_READ_REG32(&core_if-> ++ dev_if->dev_global_regs->deachintmsk); ++ } else { ++ v = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->daint) & ++ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->daintmsk); ++ } ++ ++ return ((v & 0xffff0000) >> 16); ++} ++ ++/** ++ * This function returns the Device IN EP Interrupt register ++ */ ++static inline uint32_t dwc_otg_read_dev_in_ep_intr(dwc_otg_core_if_t * core_if, ++ dwc_ep_t * ep) ++{ ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ uint32_t v, msk, emp; ++ ++ if (core_if->multiproc_int_enable) { ++ msk = ++ DWC_READ_REG32(&dev_if-> ++ dev_global_regs->diepeachintmsk[ep->num]); ++ emp = ++ DWC_READ_REG32(&dev_if-> ++ dev_global_regs->dtknqr4_fifoemptymsk); ++ msk |= ((emp >> ep->num) & 0x1) << 7; ++ v = DWC_READ_REG32(&dev_if->in_ep_regs[ep->num]->diepint) & msk; ++ } else { ++ msk = DWC_READ_REG32(&dev_if->dev_global_regs->diepmsk); ++ emp = ++ DWC_READ_REG32(&dev_if-> ++ dev_global_regs->dtknqr4_fifoemptymsk); ++ msk |= ((emp >> ep->num) & 0x1) << 7; ++ v = DWC_READ_REG32(&dev_if->in_ep_regs[ep->num]->diepint) & msk; ++ } ++ ++ return v; ++} ++ ++/** ++ * This function returns the Device OUT EP Interrupt register ++ */ ++static inline uint32_t dwc_otg_read_dev_out_ep_intr(dwc_otg_core_if_t * ++ _core_if, dwc_ep_t * _ep) ++{ ++ dwc_otg_dev_if_t *dev_if = _core_if->dev_if; ++ uint32_t v; ++ doepmsk_data_t msk = {.d32 = 0 }; ++ ++ if (_core_if->multiproc_int_enable) { ++ msk.d32 = ++ DWC_READ_REG32(&dev_if-> ++ dev_global_regs->doepeachintmsk[_ep->num]); ++ if (_core_if->pti_enh_enable) { ++ msk.b.pktdrpsts = 1; ++ } ++ v = DWC_READ_REG32(&dev_if-> ++ out_ep_regs[_ep->num]->doepint) & msk.d32; ++ } else { ++ msk.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->doepmsk); ++ if (_core_if->pti_enh_enable) { ++ msk.b.pktdrpsts = 1; ++ } ++ v = DWC_READ_REG32(&dev_if-> ++ out_ep_regs[_ep->num]->doepint) & msk.d32; ++ } ++ return v; ++} ++ ++/** ++ * This function returns the Host All Channel Interrupt register ++ */ ++static inline uint32_t dwc_otg_read_host_all_channels_intr(dwc_otg_core_if_t * ++ _core_if) ++{ ++ return (DWC_READ_REG32(&_core_if->host_if->host_global_regs->haint)); ++} ++ ++static inline uint32_t dwc_otg_read_host_channel_intr(dwc_otg_core_if_t * ++ _core_if, dwc_hc_t * _hc) ++{ ++ return (DWC_READ_REG32 ++ (&_core_if->host_if->hc_regs[_hc->hc_num]->hcint)); ++} ++ ++/** ++ * This function returns the mode of the operation, host or device. ++ * ++ * @return 0 - Device Mode, 1 - Host Mode ++ */ ++static inline uint32_t dwc_otg_mode(dwc_otg_core_if_t * _core_if) ++{ ++ return (DWC_READ_REG32(&_core_if->core_global_regs->gintsts) & 0x1); ++} ++ ++/**@}*/ ++ ++/** ++ * DWC_otg CIL callback structure. This structure allows the HCD and ++ * PCD to register functions used for starting and stopping the PCD ++ * and HCD for role change on for a DRD. ++ */ ++typedef struct dwc_otg_cil_callbacks { ++ /** Start function for role change */ ++ int (*start) (void *_p); ++ /** Stop Function for role change */ ++ int (*stop) (void *_p); ++ /** Disconnect Function for role change */ ++ int (*disconnect) (void *_p); ++ /** Resume/Remote wakeup Function */ ++ int (*resume_wakeup) (void *_p); ++ /** Suspend function */ ++ int (*suspend) (void *_p); ++ /** Session Start (SRP) */ ++ int (*session_start) (void *_p); ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ /** Sleep (switch to L0 state) */ ++ int (*sleep) (void *_p); ++#endif ++ /** Pointer passed to start() and stop() */ ++ void *p; ++} dwc_otg_cil_callbacks_t; ++ ++extern void dwc_otg_cil_register_pcd_callbacks(dwc_otg_core_if_t * _core_if, ++ dwc_otg_cil_callbacks_t * _cb, ++ void *_p); ++extern void dwc_otg_cil_register_hcd_callbacks(dwc_otg_core_if_t * _core_if, ++ dwc_otg_cil_callbacks_t * _cb, ++ void *_p); ++ ++void dwc_otg_initiate_srp(dwc_otg_core_if_t * core_if); ++ ++////////////////////////////////////////////////////////////////////// ++/** Start the HCD. Helper function for using the HCD callbacks. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++static inline void cil_hcd_start(dwc_otg_core_if_t * core_if) ++{ ++ if (core_if->hcd_cb && core_if->hcd_cb->start) { ++ core_if->hcd_cb->start(core_if->hcd_cb->p); ++ } ++} ++ ++/** Stop the HCD. Helper function for using the HCD callbacks. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++static inline void cil_hcd_stop(dwc_otg_core_if_t * core_if) ++{ ++ if (core_if->hcd_cb && core_if->hcd_cb->stop) { ++ core_if->hcd_cb->stop(core_if->hcd_cb->p); ++ } ++} ++ ++/** Disconnect the HCD. Helper function for using the HCD callbacks. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++static inline void cil_hcd_disconnect(dwc_otg_core_if_t * core_if) ++{ ++ if (core_if->hcd_cb && core_if->hcd_cb->disconnect) { ++ core_if->hcd_cb->disconnect(core_if->hcd_cb->p); ++ } ++} ++ ++/** Inform the HCD the a New Session has begun. Helper function for ++ * using the HCD callbacks. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++static inline void cil_hcd_session_start(dwc_otg_core_if_t * core_if) ++{ ++ if (core_if->hcd_cb && core_if->hcd_cb->session_start) { ++ core_if->hcd_cb->session_start(core_if->hcd_cb->p); ++ } ++} ++ ++#ifdef CONFIG_USB_DWC_OTG_LPM ++/** ++ * Inform the HCD about LPM sleep. ++ * Helper function for using the HCD callbacks. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++static inline void cil_hcd_sleep(dwc_otg_core_if_t * core_if) ++{ ++ if (core_if->hcd_cb && core_if->hcd_cb->sleep) { ++ core_if->hcd_cb->sleep(core_if->hcd_cb->p); ++ } ++} ++#endif ++ ++/** Resume the HCD. Helper function for using the HCD callbacks. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++static inline void cil_hcd_resume(dwc_otg_core_if_t * core_if) ++{ ++ if (core_if->hcd_cb && core_if->hcd_cb->resume_wakeup) { ++ core_if->hcd_cb->resume_wakeup(core_if->hcd_cb->p); ++ } ++} ++ ++/** Start the PCD. Helper function for using the PCD callbacks. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++static inline void cil_pcd_start(dwc_otg_core_if_t * core_if) ++{ ++ if (core_if->pcd_cb && core_if->pcd_cb->start) { ++ core_if->pcd_cb->start(core_if->pcd_cb->p); ++ } ++} ++ ++/** Stop the PCD. Helper function for using the PCD callbacks. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++static inline void cil_pcd_stop(dwc_otg_core_if_t * core_if) ++{ ++ if (core_if->pcd_cb && core_if->pcd_cb->stop) { ++ core_if->pcd_cb->stop(core_if->pcd_cb->p); ++ } ++} ++ ++/** Suspend the PCD. Helper function for using the PCD callbacks. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++static inline void cil_pcd_suspend(dwc_otg_core_if_t * core_if) ++{ ++ if (core_if->pcd_cb && core_if->pcd_cb->suspend) { ++ core_if->pcd_cb->suspend(core_if->pcd_cb->p); ++ } ++} ++ ++/** Resume the PCD. Helper function for using the PCD callbacks. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++static inline void cil_pcd_resume(dwc_otg_core_if_t * core_if) ++{ ++ if (core_if->pcd_cb && core_if->pcd_cb->resume_wakeup) { ++ core_if->pcd_cb->resume_wakeup(core_if->pcd_cb->p); ++ } ++} ++ ++////////////////////////////////////////////////////////////////////// ++ ++#endif +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_cil_intr.c +@@ -0,0 +1,1601 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_cil_intr.c $ ++ * $Revision: #32 $ ++ * $Date: 2012/08/10 $ ++ * $Change: 2047372 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++/** @file ++ * ++ * The Core Interface Layer provides basic services for accessing and ++ * managing the DWC_otg hardware. These services are used by both the ++ * Host Controller Driver and the Peripheral Controller Driver. ++ * ++ * This file contains the Common Interrupt handlers. ++ */ ++#include "dwc_os.h" ++#include "dwc_otg_regs.h" ++#include "dwc_otg_cil.h" ++#include "dwc_otg_driver.h" ++#include "dwc_otg_pcd.h" ++#include "dwc_otg_hcd.h" ++ ++#ifdef DEBUG ++inline const char *op_state_str(dwc_otg_core_if_t * core_if) ++{ ++ return (core_if->op_state == A_HOST ? "a_host" : ++ (core_if->op_state == A_SUSPEND ? "a_suspend" : ++ (core_if->op_state == A_PERIPHERAL ? "a_peripheral" : ++ (core_if->op_state == B_PERIPHERAL ? "b_peripheral" : ++ (core_if->op_state == B_HOST ? "b_host" : "unknown"))))); ++} ++#endif ++ ++/** This function will log a debug message ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++int32_t dwc_otg_handle_mode_mismatch_intr(dwc_otg_core_if_t * core_if) ++{ ++ gintsts_data_t gintsts; ++ DWC_WARN("Mode Mismatch Interrupt: currently in %s mode\n", ++ dwc_otg_mode(core_if) ? "Host" : "Device"); ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.modemismatch = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ return 1; ++} ++ ++/** ++ * This function handles the OTG Interrupts. It reads the OTG ++ * Interrupt Register (GOTGINT) to determine what interrupt has ++ * occurred. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++int32_t dwc_otg_handle_otg_intr(dwc_otg_core_if_t * core_if) ++{ ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ gotgint_data_t gotgint; ++ gotgctl_data_t gotgctl; ++ gintmsk_data_t gintmsk; ++ gpwrdn_data_t gpwrdn; ++ ++ gotgint.d32 = DWC_READ_REG32(&global_regs->gotgint); ++ gotgctl.d32 = DWC_READ_REG32(&global_regs->gotgctl); ++ DWC_DEBUGPL(DBG_CIL, "++OTG Interrupt gotgint=%0x [%s]\n", gotgint.d32, ++ op_state_str(core_if)); ++ ++ if (gotgint.b.sesenddet) { ++ DWC_DEBUGPL(DBG_ANY, " ++OTG Interrupt: " ++ "Session End Detected++ (%s)\n", ++ op_state_str(core_if)); ++ gotgctl.d32 = DWC_READ_REG32(&global_regs->gotgctl); ++ ++ if (core_if->op_state == B_HOST) { ++ cil_pcd_start(core_if); ++ core_if->op_state = B_PERIPHERAL; ++ } else { ++ /* If not B_HOST and Device HNP still set. HNP ++ * Did not succeed!*/ ++ if (gotgctl.b.devhnpen) { ++ DWC_DEBUGPL(DBG_ANY, "Session End Detected\n"); ++ __DWC_ERROR("Device Not Connected/Responding!\n"); ++ } ++ ++ /* If Session End Detected the B-Cable has ++ * been disconnected. */ ++ /* Reset PCD and Gadget driver to a ++ * clean state. */ ++ core_if->lx_state = DWC_OTG_L0; ++ DWC_SPINUNLOCK(core_if->lock); ++ cil_pcd_stop(core_if); ++ DWC_SPINLOCK(core_if->lock); ++ ++ if (core_if->adp_enable) { ++ if (core_if->power_down == 2) { ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if-> ++ core_global_regs-> ++ gpwrdn, gpwrdn.d32, 0); ++ } ++ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ ++ dwc_otg_adp_sense_start(core_if); ++ } ++ } ++ ++ gotgctl.d32 = 0; ++ gotgctl.b.devhnpen = 1; ++ DWC_MODIFY_REG32(&global_regs->gotgctl, gotgctl.d32, 0); ++ } ++ if (gotgint.b.sesreqsucstschng) { ++ DWC_DEBUGPL(DBG_ANY, " ++OTG Interrupt: " ++ "Session Reqeust Success Status Change++\n"); ++ gotgctl.d32 = DWC_READ_REG32(&global_regs->gotgctl); ++ if (gotgctl.b.sesreqscs) { ++ ++ if ((core_if->core_params->phy_type == ++ DWC_PHY_TYPE_PARAM_FS) && (core_if->core_params->i2c_enable)) { ++ core_if->srp_success = 1; ++ } else { ++ DWC_SPINUNLOCK(core_if->lock); ++ cil_pcd_resume(core_if); ++ DWC_SPINLOCK(core_if->lock); ++ /* Clear Session Request */ ++ gotgctl.d32 = 0; ++ gotgctl.b.sesreq = 1; ++ DWC_MODIFY_REG32(&global_regs->gotgctl, ++ gotgctl.d32, 0); ++ } ++ } ++ } ++ if (gotgint.b.hstnegsucstschng) { ++ /* Print statements during the HNP interrupt handling ++ * can cause it to fail.*/ ++ gotgctl.d32 = DWC_READ_REG32(&global_regs->gotgctl); ++ /* WA for 3.00a- HW is not setting cur_mode, even sometimes ++ * this does not help*/ ++ if (core_if->snpsid >= OTG_CORE_REV_3_00a) ++ dwc_udelay(100); ++ if (gotgctl.b.hstnegscs) { ++ if (dwc_otg_is_host_mode(core_if)) { ++ core_if->op_state = B_HOST; ++ /* ++ * Need to disable SOF interrupt immediately. ++ * When switching from device to host, the PCD ++ * interrupt handler won't handle the ++ * interrupt if host mode is already set. The ++ * HCD interrupt handler won't get called if ++ * the HCD state is HALT. This means that the ++ * interrupt does not get handled and Linux ++ * complains loudly. ++ */ ++ gintmsk.d32 = 0; ++ gintmsk.b.sofintr = 1; ++ DWC_MODIFY_REG32(&global_regs->gintmsk, ++ gintmsk.d32, 0); ++ /* Call callback function with spin lock released */ ++ DWC_SPINUNLOCK(core_if->lock); ++ cil_pcd_stop(core_if); ++ /* ++ * Initialize the Core for Host mode. ++ */ ++ cil_hcd_start(core_if); ++ DWC_SPINLOCK(core_if->lock); ++ core_if->op_state = B_HOST; ++ } ++ } else { ++ gotgctl.d32 = 0; ++ gotgctl.b.hnpreq = 1; ++ gotgctl.b.devhnpen = 1; ++ DWC_MODIFY_REG32(&global_regs->gotgctl, gotgctl.d32, 0); ++ DWC_DEBUGPL(DBG_ANY, "HNP Failed\n"); ++ __DWC_ERROR("Device Not Connected/Responding\n"); ++ } ++ } ++ if (gotgint.b.hstnegdet) { ++ /* The disconnect interrupt is set at the same time as ++ * Host Negotiation Detected. During the mode ++ * switch all interrupts are cleared so the disconnect ++ * interrupt handler will not get executed. ++ */ ++ DWC_DEBUGPL(DBG_ANY, " ++OTG Interrupt: " ++ "Host Negotiation Detected++ (%s)\n", ++ (dwc_otg_is_host_mode(core_if) ? "Host" : ++ "Device")); ++ if (dwc_otg_is_device_mode(core_if)) { ++ DWC_DEBUGPL(DBG_ANY, "a_suspend->a_peripheral (%d)\n", ++ core_if->op_state); ++ DWC_SPINUNLOCK(core_if->lock); ++ cil_hcd_disconnect(core_if); ++ cil_pcd_start(core_if); ++ DWC_SPINLOCK(core_if->lock); ++ core_if->op_state = A_PERIPHERAL; ++ } else { ++ /* ++ * Need to disable SOF interrupt immediately. When ++ * switching from device to host, the PCD interrupt ++ * handler won't handle the interrupt if host mode is ++ * already set. The HCD interrupt handler won't get ++ * called if the HCD state is HALT. This means that ++ * the interrupt does not get handled and Linux ++ * complains loudly. ++ */ ++ gintmsk.d32 = 0; ++ gintmsk.b.sofintr = 1; ++ DWC_MODIFY_REG32(&global_regs->gintmsk, gintmsk.d32, 0); ++ DWC_SPINUNLOCK(core_if->lock); ++ cil_pcd_stop(core_if); ++ cil_hcd_start(core_if); ++ DWC_SPINLOCK(core_if->lock); ++ core_if->op_state = A_HOST; ++ } ++ } ++ if (gotgint.b.adevtoutchng) { ++ DWC_DEBUGPL(DBG_ANY, " ++OTG Interrupt: " ++ "A-Device Timeout Change++\n"); ++ } ++ if (gotgint.b.debdone) { ++ DWC_DEBUGPL(DBG_ANY, " ++OTG Interrupt: " "Debounce Done++\n"); ++ } ++ ++ /* Clear GOTGINT */ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gotgint, gotgint.d32); ++ ++ return 1; ++} ++ ++void w_conn_id_status_change(void *p) ++{ ++ dwc_otg_core_if_t *core_if = p; ++ uint32_t count = 0; ++ gotgctl_data_t gotgctl = {.d32 = 0 }; ++ ++ gotgctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->gotgctl); ++ DWC_DEBUGPL(DBG_CIL, "gotgctl=%0x\n", gotgctl.d32); ++ DWC_DEBUGPL(DBG_CIL, "gotgctl.b.conidsts=%d\n", gotgctl.b.conidsts); ++ ++ /* B-Device connector (Device Mode) */ ++ if (gotgctl.b.conidsts) { ++ /* Wait for switch to device mode. */ ++ while (!dwc_otg_is_device_mode(core_if)) { ++ DWC_PRINTF("Waiting for Peripheral Mode, Mode=%s\n", ++ (dwc_otg_is_host_mode(core_if) ? "Host" : ++ "Peripheral")); ++ dwc_mdelay(100); ++ if (++count > 10000) ++ break; ++ } ++ DWC_ASSERT(++count < 10000, ++ "Connection id status change timed out"); ++ core_if->op_state = B_PERIPHERAL; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_pcd_start(core_if); ++ } else { ++ /* A-Device connector (Host Mode) */ ++ while (!dwc_otg_is_host_mode(core_if)) { ++ DWC_PRINTF("Waiting for Host Mode, Mode=%s\n", ++ (dwc_otg_is_host_mode(core_if) ? "Host" : ++ "Peripheral")); ++ dwc_mdelay(100); ++ if (++count > 10000) ++ break; ++ } ++ DWC_ASSERT(++count < 10000, ++ "Connection id status change timed out"); ++ core_if->op_state = A_HOST; ++ /* ++ * Initialize the Core for Host mode. ++ */ ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_hcd_start(core_if); ++ } ++} ++ ++/** ++ * This function handles the Connector ID Status Change Interrupt. It ++ * reads the OTG Interrupt Register (GOTCTL) to determine whether this ++ * is a Device to Host Mode transition or a Host Mode to Device ++ * Transition. ++ * ++ * This only occurs when the cable is connected/removed from the PHY ++ * connector. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++int32_t dwc_otg_handle_conn_id_status_change_intr(dwc_otg_core_if_t * core_if) ++{ ++ ++ /* ++ * Need to disable SOF interrupt immediately. If switching from device ++ * to host, the PCD interrupt handler won't handle the interrupt if ++ * host mode is already set. The HCD interrupt handler won't get ++ * called if the HCD state is HALT. This means that the interrupt does ++ * not get handled and Linux complains loudly. ++ */ ++ gintmsk_data_t gintmsk = {.d32 = 0 }; ++ gintsts_data_t gintsts = {.d32 = 0 }; ++ ++ gintmsk.b.sofintr = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, gintmsk.d32, 0); ++ ++ DWC_DEBUGPL(DBG_CIL, ++ " ++Connector ID Status Change Interrupt++ (%s)\n", ++ (dwc_otg_is_host_mode(core_if) ? "Host" : "Device")); ++ ++ DWC_SPINUNLOCK(core_if->lock); ++ ++ /* ++ * Need to schedule a work, as there are possible DELAY function calls ++ * Release lock before scheduling workq as it holds spinlock during scheduling ++ */ ++ ++ DWC_WORKQ_SCHEDULE(core_if->wq_otg, w_conn_id_status_change, ++ core_if, "connection id status change"); ++ DWC_SPINLOCK(core_if->lock); ++ ++ /* Set flag and clear interrupt */ ++ gintsts.b.conidstschng = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ ++ return 1; ++} ++ ++/** ++ * This interrupt indicates that a device is initiating the Session ++ * Request Protocol to request the host to turn on bus power so a new ++ * session can begin. The handler responds by turning on bus power. If ++ * the DWC_otg controller is in low power mode, the handler brings the ++ * controller out of low power mode before turning on bus power. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++int32_t dwc_otg_handle_session_req_intr(dwc_otg_core_if_t * core_if) ++{ ++ gintsts_data_t gintsts; ++ ++#ifndef DWC_HOST_ONLY ++ DWC_DEBUGPL(DBG_ANY, "++Session Request Interrupt++\n"); ++ ++ if (dwc_otg_is_device_mode(core_if)) { ++ DWC_PRINTF("SRP: Device mode\n"); ++ } else { ++ hprt0_data_t hprt0; ++ DWC_PRINTF("SRP: Host mode\n"); ++ ++ /* Turn on the port power bit. */ ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtpwr = 1; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ ++ /* Start the Connection timer. So a message can be displayed ++ * if connect does not occur within 10 seconds. */ ++ cil_hcd_session_start(core_if); ++ } ++#endif ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.sessreqintr = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ ++ return 1; ++} ++ ++void w_wakeup_detected(void *p) ++{ ++ dwc_otg_core_if_t *core_if = (dwc_otg_core_if_t *) p; ++ /* ++ * Clear the Resume after 70ms. (Need 20 ms minimum. Use 70 ms ++ * so that OPT tests pass with all PHYs). ++ */ ++ hprt0_data_t hprt0 = {.d32 = 0 }; ++#if 0 ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ /* Restart the Phy Clock */ ++ pcgcctl.b.stoppclk = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0); ++ dwc_udelay(10); ++#endif //0 ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ DWC_DEBUGPL(DBG_ANY, "Resume: HPRT0=%0x\n", hprt0.d32); ++// dwc_mdelay(70); ++ hprt0.b.prtres = 0; /* Resume */ ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ DWC_DEBUGPL(DBG_ANY, "Clear Resume: HPRT0=%0x\n", ++ DWC_READ_REG32(core_if->host_if->hprt0)); ++ ++ cil_hcd_resume(core_if); ++ ++ /** Change to L0 state*/ ++ core_if->lx_state = DWC_OTG_L0; ++} ++ ++/** ++ * This interrupt indicates that the DWC_otg controller has detected a ++ * resume or remote wakeup sequence. If the DWC_otg controller is in ++ * low power mode, the handler must brings the controller out of low ++ * power mode. The controller automatically begins resume ++ * signaling. The handler schedules a time to stop resume signaling. ++ */ ++int32_t dwc_otg_handle_wakeup_detected_intr(dwc_otg_core_if_t * core_if) ++{ ++ gintsts_data_t gintsts; ++ ++ DWC_DEBUGPL(DBG_ANY, ++ "++Resume and Remote Wakeup Detected Interrupt++\n"); ++ ++ DWC_PRINTF("%s lxstate = %d\n", __func__, core_if->lx_state); ++ ++ if (dwc_otg_is_device_mode(core_if)) { ++ dctl_data_t dctl = {.d32 = 0 }; ++ DWC_DEBUGPL(DBG_PCD, "DSTS=0x%0x\n", ++ DWC_READ_REG32(&core_if->dev_if->dev_global_regs-> ++ dsts)); ++ if (core_if->lx_state == DWC_OTG_L2) { ++#ifdef PARTIAL_POWER_DOWN ++ if (core_if->hwcfg4.b.power_optimiz) { ++ pcgcctl_data_t power = {.d32 = 0 }; ++ ++ power.d32 = DWC_READ_REG32(core_if->pcgcctl); ++ DWC_DEBUGPL(DBG_CIL, "PCGCCTL=%0x\n", ++ power.d32); ++ ++ power.b.stoppclk = 0; ++ DWC_WRITE_REG32(core_if->pcgcctl, power.d32); ++ ++ power.b.pwrclmp = 0; ++ DWC_WRITE_REG32(core_if->pcgcctl, power.d32); ++ ++ power.b.rstpdwnmodule = 0; ++ DWC_WRITE_REG32(core_if->pcgcctl, power.d32); ++ } ++#endif ++ /* Clear the Remote Wakeup Signaling */ ++ dctl.b.rmtwkupsig = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs-> ++ dctl, dctl.d32, 0); ++ ++ DWC_SPINUNLOCK(core_if->lock); ++ if (core_if->pcd_cb && core_if->pcd_cb->resume_wakeup) { ++ core_if->pcd_cb->resume_wakeup(core_if->pcd_cb->p); ++ } ++ DWC_SPINLOCK(core_if->lock); ++ } else { ++ glpmcfg_data_t lpmcfg; ++ lpmcfg.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ lpmcfg.b.hird_thres &= (~(1 << 4)); ++ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg, ++ lpmcfg.d32); ++ } ++ /** Change to L0 state*/ ++ core_if->lx_state = DWC_OTG_L0; ++ } else { ++ if (core_if->lx_state != DWC_OTG_L1) { ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ ++ /* Restart the Phy Clock */ ++ pcgcctl.b.stoppclk = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0); ++ DWC_TIMER_SCHEDULE(core_if->wkp_timer, 71); ++ } else { ++ /** Change to L0 state*/ ++ core_if->lx_state = DWC_OTG_L0; ++ } ++ } ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.wkupintr = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ ++ return 1; ++} ++ ++/** ++ * This interrupt indicates that the Wakeup Logic has detected a ++ * Device disconnect. ++ */ ++static int32_t dwc_otg_handle_pwrdn_disconnect_intr(dwc_otg_core_if_t *core_if) ++{ ++ gpwrdn_data_t gpwrdn = { .d32 = 0 }; ++ gpwrdn_data_t gpwrdn_temp = { .d32 = 0 }; ++ gpwrdn_temp.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ ++ DWC_PRINTF("%s called\n", __FUNCTION__); ++ ++ if (!core_if->hibernation_suspend) { ++ DWC_PRINTF("Already exited from Hibernation\n"); ++ return 1; ++ } ++ ++ /* Switch on the voltage to the core */ ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Reset the core */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Disable power clamps*/ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnclmp = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ /* Remove reset the core signal */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Disable PMU interrupt */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ core_if->hibernation_suspend = 0; ++ ++ /* Disable PMU */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ if (gpwrdn_temp.b.idsts) { ++ core_if->op_state = B_PERIPHERAL; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_pcd_start(core_if); ++ } else { ++ core_if->op_state = A_HOST; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_hcd_start(core_if); ++ } ++ ++ return 1; ++} ++ ++/** ++ * This interrupt indicates that the Wakeup Logic has detected a ++ * remote wakeup sequence. ++ */ ++static int32_t dwc_otg_handle_pwrdn_wakeup_detected_intr(dwc_otg_core_if_t * core_if) ++{ ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ DWC_DEBUGPL(DBG_ANY, ++ "++Powerdown Remote Wakeup Detected Interrupt++\n"); ++ ++ if (!core_if->hibernation_suspend) { ++ DWC_PRINTF("Already exited from Hibernation\n"); ++ return 1; ++ } ++ ++ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ if (gpwrdn.b.idsts) { // Device Mode ++ if ((core_if->power_down == 2) ++ && (core_if->hibernation_suspend == 1)) { ++ dwc_otg_device_hibernation_restore(core_if, 0, 0); ++ } ++ } else { ++ if ((core_if->power_down == 2) ++ && (core_if->hibernation_suspend == 1)) { ++ dwc_otg_host_hibernation_restore(core_if, 1, 0); ++ } ++ } ++ return 1; ++} ++ ++static int32_t dwc_otg_handle_pwrdn_idsts_change(dwc_otg_device_t *otg_dev) ++{ ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ gpwrdn_data_t gpwrdn_temp = {.d32 = 0 }; ++ dwc_otg_core_if_t *core_if = otg_dev->core_if; ++ ++ DWC_DEBUGPL(DBG_ANY, "%s called\n", __FUNCTION__); ++ gpwrdn_temp.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ if (core_if->power_down == 2) { ++ if (!core_if->hibernation_suspend) { ++ DWC_PRINTF("Already exited from Hibernation\n"); ++ return 1; ++ } ++ DWC_DEBUGPL(DBG_ANY, "Exit from hibernation on ID sts change\n"); ++ /* Switch on the voltage to the core */ ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Reset the core */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Disable power clamps */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnclmp = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ /* Remove reset the core signal */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Disable PMU interrupt */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ /*Indicates that we are exiting from hibernation */ ++ core_if->hibernation_suspend = 0; ++ ++ /* Disable PMU */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ gpwrdn.d32 = core_if->gr_backup->gpwrdn_local; ++ if (gpwrdn.b.dis_vbus == 1) { ++ gpwrdn.d32 = 0; ++ gpwrdn.b.dis_vbus = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ } ++ ++ if (gpwrdn_temp.b.idsts) { ++ core_if->op_state = B_PERIPHERAL; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_pcd_start(core_if); ++ } else { ++ core_if->op_state = A_HOST; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_hcd_start(core_if); ++ } ++ } ++ ++ if (core_if->adp_enable) { ++ uint8_t is_host = 0; ++ DWC_SPINUNLOCK(core_if->lock); ++ /* Change the core_if's lock to hcd/pcd lock depend on mode? */ ++#ifndef DWC_HOST_ONLY ++ if (gpwrdn_temp.b.idsts) ++ core_if->lock = otg_dev->pcd->lock; ++#endif ++#ifndef DWC_DEVICE_ONLY ++ if (!gpwrdn_temp.b.idsts) { ++ core_if->lock = otg_dev->hcd->lock; ++ is_host = 1; ++ } ++#endif ++ DWC_PRINTF("RESTART ADP\n"); ++ if (core_if->adp.probe_enabled) ++ dwc_otg_adp_probe_stop(core_if); ++ if (core_if->adp.sense_enabled) ++ dwc_otg_adp_sense_stop(core_if); ++ if (core_if->adp.sense_timer_started) ++ DWC_TIMER_CANCEL(core_if->adp.sense_timer); ++ if (core_if->adp.vbuson_timer_started) ++ DWC_TIMER_CANCEL(core_if->adp.vbuson_timer); ++ core_if->adp.probe_timer_values[0] = -1; ++ core_if->adp.probe_timer_values[1] = -1; ++ core_if->adp.sense_timer_started = 0; ++ core_if->adp.vbuson_timer_started = 0; ++ core_if->adp.probe_counter = 0; ++ core_if->adp.gpwrdn = 0; ++ ++ /* Disable PMU and restart ADP */ ++ gpwrdn_temp.d32 = 0; ++ gpwrdn_temp.b.pmuactv = 1; ++ gpwrdn_temp.b.pmuintsel = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ DWC_PRINTF("Check point 1\n"); ++ dwc_mdelay(110); ++ dwc_otg_adp_start(core_if, is_host); ++ DWC_SPINLOCK(core_if->lock); ++ } ++ ++ ++ return 1; ++} ++ ++static int32_t dwc_otg_handle_pwrdn_session_change(dwc_otg_core_if_t * core_if) ++{ ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ int32_t otg_cap_param = core_if->core_params->otg_cap; ++ DWC_DEBUGPL(DBG_ANY, "%s called\n", __FUNCTION__); ++ ++ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ if (core_if->power_down == 2) { ++ if (!core_if->hibernation_suspend) { ++ DWC_PRINTF("Already exited from Hibernation\n"); ++ return 1; ++ } ++ ++ if ((otg_cap_param != DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE || ++ otg_cap_param != DWC_OTG_CAP_PARAM_SRP_ONLY_CAPABLE) && ++ gpwrdn.b.bsessvld == 0) { ++ /* Save gpwrdn register for further usage if stschng interrupt */ ++ core_if->gr_backup->gpwrdn_local = ++ DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ /*Exit from ISR and wait for stschng interrupt with bsessvld = 1 */ ++ return 1; ++ } ++ ++ /* Switch on the voltage to the core */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Reset the core */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Disable power clamps */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnclmp = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ /* Remove reset the core signal */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Disable PMU interrupt */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /*Indicates that we are exiting from hibernation */ ++ core_if->hibernation_suspend = 0; ++ ++ /* Disable PMU */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ core_if->op_state = B_PERIPHERAL; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_pcd_start(core_if); ++ ++ if (otg_cap_param == DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE || ++ otg_cap_param == DWC_OTG_CAP_PARAM_SRP_ONLY_CAPABLE) { ++ /* ++ * Initiate SRP after initial ADP probe. ++ */ ++ dwc_otg_initiate_srp(core_if); ++ } ++ } ++ ++ return 1; ++} ++/** ++ * This interrupt indicates that the Wakeup Logic has detected a ++ * status change either on IDDIG or BSessVld. ++ */ ++static uint32_t dwc_otg_handle_pwrdn_stschng_intr(dwc_otg_device_t *otg_dev) ++{ ++ int retval; ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ gpwrdn_data_t gpwrdn_temp = {.d32 = 0 }; ++ dwc_otg_core_if_t *core_if = otg_dev->core_if; ++ ++ DWC_PRINTF("%s called\n", __FUNCTION__); ++ ++ if (core_if->power_down == 2) { ++ if (core_if->hibernation_suspend <= 0) { ++ DWC_PRINTF("Already exited from Hibernation\n"); ++ return 1; ++ } else ++ gpwrdn_temp.d32 = core_if->gr_backup->gpwrdn_local; ++ ++ } else { ++ gpwrdn_temp.d32 = core_if->adp.gpwrdn; ++ } ++ ++ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ ++ if (gpwrdn.b.idsts ^ gpwrdn_temp.b.idsts) { ++ retval = dwc_otg_handle_pwrdn_idsts_change(otg_dev); ++ } else if (gpwrdn.b.bsessvld ^ gpwrdn_temp.b.bsessvld) { ++ retval = dwc_otg_handle_pwrdn_session_change(core_if); ++ } ++ ++ return retval; ++} ++ ++/** ++ * This interrupt indicates that the Wakeup Logic has detected a ++ * SRP. ++ */ ++static int32_t dwc_otg_handle_pwrdn_srp_intr(dwc_otg_core_if_t * core_if) ++{ ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ ++ DWC_PRINTF("%s called\n", __FUNCTION__); ++ ++ if (!core_if->hibernation_suspend) { ++ DWC_PRINTF("Already exited from Hibernation\n"); ++ return 1; ++ } ++#ifdef DWC_DEV_SRPCAP ++ if (core_if->pwron_timer_started) { ++ core_if->pwron_timer_started = 0; ++ DWC_TIMER_CANCEL(core_if->pwron_timer); ++ } ++#endif ++ ++ /* Switch on the voltage to the core */ ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Reset the core */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Disable power clamps */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnclmp = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ /* Remove reset the core signal */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Disable PMU interrupt */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ /* Indicates that we are exiting from hibernation */ ++ core_if->hibernation_suspend = 0; ++ ++ /* Disable PMU */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Programm Disable VBUS to 0 */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.dis_vbus = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ /*Initialize the core as Host */ ++ core_if->op_state = A_HOST; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_hcd_start(core_if); ++ ++ return 1; ++} ++ ++/** This interrupt indicates that restore command after Hibernation ++ * was completed by the core. */ ++int32_t dwc_otg_handle_restore_done_intr(dwc_otg_core_if_t * core_if) ++{ ++ pcgcctl_data_t pcgcctl; ++ DWC_DEBUGPL(DBG_ANY, "++Restore Done Interrupt++\n"); ++ ++ //TODO De-assert restore signal. 8.a ++ pcgcctl.d32 = DWC_READ_REG32(core_if->pcgcctl); ++ if (pcgcctl.b.restoremode == 1) { ++ gintmsk_data_t gintmsk = {.d32 = 0 }; ++ /* ++ * If restore mode is Remote Wakeup, ++ * unmask Remote Wakeup interrupt. ++ */ ++ gintmsk.b.wkupintr = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, ++ 0, gintmsk.d32); ++ } ++ ++ return 1; ++} ++ ++/** ++ * This interrupt indicates that a device has been disconnected from ++ * the root port. ++ */ ++int32_t dwc_otg_handle_disconnect_intr(dwc_otg_core_if_t * core_if) ++{ ++ gintsts_data_t gintsts; ++ ++ DWC_DEBUGPL(DBG_ANY, "++Disconnect Detected Interrupt++ (%s) %s\n", ++ (dwc_otg_is_host_mode(core_if) ? "Host" : "Device"), ++ op_state_str(core_if)); ++ ++/** @todo Consolidate this if statement. */ ++#ifndef DWC_HOST_ONLY ++ if (core_if->op_state == B_HOST) { ++ /* If in device mode Disconnect and stop the HCD, then ++ * start the PCD. */ ++ DWC_SPINUNLOCK(core_if->lock); ++ cil_hcd_disconnect(core_if); ++ cil_pcd_start(core_if); ++ DWC_SPINLOCK(core_if->lock); ++ core_if->op_state = B_PERIPHERAL; ++ } else if (dwc_otg_is_device_mode(core_if)) { ++ gotgctl_data_t gotgctl = {.d32 = 0 }; ++ gotgctl.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->gotgctl); ++ if (gotgctl.b.hstsethnpen == 1) { ++ /* Do nothing, if HNP in process the OTG ++ * interrupt "Host Negotiation Detected" ++ * interrupt will do the mode switch. ++ */ ++ } else if (gotgctl.b.devhnpen == 0) { ++ /* If in device mode Disconnect and stop the HCD, then ++ * start the PCD. */ ++ DWC_SPINUNLOCK(core_if->lock); ++ cil_hcd_disconnect(core_if); ++ cil_pcd_start(core_if); ++ DWC_SPINLOCK(core_if->lock); ++ core_if->op_state = B_PERIPHERAL; ++ } else { ++ DWC_DEBUGPL(DBG_ANY, "!a_peripheral && !devhnpen\n"); ++ } ++ } else { ++ if (core_if->op_state == A_HOST) { ++ /* A-Cable still connected but device disconnected. */ ++ DWC_SPINUNLOCK(core_if->lock); ++ cil_hcd_disconnect(core_if); ++ DWC_SPINLOCK(core_if->lock); ++ if (core_if->adp_enable) { ++ gpwrdn_data_t gpwrdn = { .d32 = 0 }; ++ cil_hcd_stop(core_if); ++ /* Enable Power Down Logic */ ++ gpwrdn.b.pmuintsel = 1; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ dwc_otg_adp_probe_start(core_if); ++ ++ /* Power off the core */ ++ if (core_if->power_down == 2) { ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32 ++ (&core_if->core_global_regs->gpwrdn, ++ gpwrdn.d32, 0); ++ } ++ } ++ } ++ } ++#endif ++ /* Change to L3(OFF) state */ ++ core_if->lx_state = DWC_OTG_L3; ++ ++ gintsts.d32 = 0; ++ gintsts.b.disconnect = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ return 1; ++} ++ ++/** ++ * This interrupt indicates that SUSPEND state has been detected on ++ * the USB. ++ * ++ * For HNP the USB Suspend interrupt signals the change from ++ * "a_peripheral" to "a_host". ++ * ++ * When power management is enabled the core will be put in low power ++ * mode. ++ */ ++int32_t dwc_otg_handle_usb_suspend_intr(dwc_otg_core_if_t * core_if) ++{ ++ dsts_data_t dsts; ++ gintsts_data_t gintsts; ++ dcfg_data_t dcfg; ++ ++ DWC_DEBUGPL(DBG_ANY, "USB SUSPEND\n"); ++ ++ if (dwc_otg_is_device_mode(core_if)) { ++ /* Check the Device status register to determine if the Suspend ++ * state is active. */ ++ dsts.d32 = ++ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts); ++ DWC_DEBUGPL(DBG_PCD, "DSTS=0x%0x\n", dsts.d32); ++ DWC_DEBUGPL(DBG_PCD, "DSTS.Suspend Status=%d " ++ "HWCFG4.power Optimize=%d\n", ++ dsts.b.suspsts, core_if->hwcfg4.b.power_optimiz); ++ ++#ifdef PARTIAL_POWER_DOWN ++/** @todo Add a module parameter for power management. */ ++ ++ if (dsts.b.suspsts && core_if->hwcfg4.b.power_optimiz) { ++ pcgcctl_data_t power = {.d32 = 0 }; ++ DWC_DEBUGPL(DBG_CIL, "suspend\n"); ++ ++ power.b.pwrclmp = 1; ++ DWC_WRITE_REG32(core_if->pcgcctl, power.d32); ++ ++ power.b.rstpdwnmodule = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, 0, power.d32); ++ ++ power.b.stoppclk = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, 0, power.d32); ++ ++ } else { ++ DWC_DEBUGPL(DBG_ANY, "disconnect?\n"); ++ } ++#endif ++ /* PCD callback for suspend. Release the lock inside of callback function */ ++ cil_pcd_suspend(core_if); ++ if (core_if->power_down == 2) ++ { ++ dcfg.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg); ++ DWC_DEBUGPL(DBG_ANY,"lx_state = %08x\n",core_if->lx_state); ++ DWC_DEBUGPL(DBG_ANY," device address = %08d\n",dcfg.b.devaddr); ++ ++ if (core_if->lx_state != DWC_OTG_L3 && dcfg.b.devaddr) { ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ gusbcfg_data_t gusbcfg = {.d32 = 0 }; ++ ++ /* Change to L2(suspend) state */ ++ core_if->lx_state = DWC_OTG_L2; ++ ++ /* Clear interrupt in gintsts */ ++ gintsts.d32 = 0; ++ gintsts.b.usbsuspend = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs-> ++ gintsts, gintsts.d32); ++ DWC_PRINTF("Start of hibernation completed\n"); ++ dwc_otg_save_global_regs(core_if); ++ dwc_otg_save_dev_regs(core_if); ++ ++ gusbcfg.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs-> ++ gusbcfg); ++ if (gusbcfg.b.ulpi_utmi_sel == 1) { ++ /* ULPI interface */ ++ /* Suspend the Phy Clock */ ++ pcgcctl.d32 = 0; ++ pcgcctl.b.stoppclk = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, 0, ++ pcgcctl.d32); ++ dwc_udelay(10); ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if-> ++ core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ } else { ++ /* UTMI+ Interface */ ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if-> ++ core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ pcgcctl.b.stoppclk = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, 0, ++ pcgcctl.d32); ++ dwc_udelay(10); ++ } ++ ++ /* Set flag to indicate that we are in hibernation */ ++ core_if->hibernation_suspend = 1; ++ /* Enable interrupts from wake up logic */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Unmask device mode interrupts in GPWRDN */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.rst_det_msk = 1; ++ gpwrdn.b.lnstchng_msk = 1; ++ gpwrdn.b.sts_chngint_msk = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Enable Power Down Clamp */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnclmp = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Switch off VDD */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ ++ /* Save gpwrdn register for further usage if stschng interrupt */ ++ core_if->gr_backup->gpwrdn_local = ++ DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ DWC_PRINTF("Hibernation completed\n"); ++ ++ return 1; ++ } ++ } else if (core_if->power_down == 3) { ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ dcfg.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dcfg); ++ DWC_DEBUGPL(DBG_ANY, "lx_state = %08x\n",core_if->lx_state); ++ DWC_DEBUGPL(DBG_ANY, " device address = %08d\n",dcfg.b.devaddr); ++ ++ if (core_if->lx_state != DWC_OTG_L3 && dcfg.b.devaddr) { ++ DWC_DEBUGPL(DBG_ANY, "Start entering to extended hibernation\n"); ++ core_if->xhib = 1; ++ ++ /* Clear interrupt in gintsts */ ++ gintsts.d32 = 0; ++ gintsts.b.usbsuspend = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs-> ++ gintsts, gintsts.d32); ++ ++ dwc_otg_save_global_regs(core_if); ++ dwc_otg_save_dev_regs(core_if); ++ ++ /* Wait for 10 PHY clocks */ ++ dwc_udelay(10); ++ ++ /* Program GPIO register while entering to xHib */ ++ DWC_WRITE_REG32(&core_if->core_global_regs->ggpio, 0x1); ++ ++ pcgcctl.b.enbl_extnd_hiber = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, 0, pcgcctl.d32); ++ DWC_MODIFY_REG32(core_if->pcgcctl, 0, pcgcctl.d32); ++ ++ pcgcctl.d32 = 0; ++ pcgcctl.b.extnd_hiber_pwrclmp = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, 0, pcgcctl.d32); ++ ++ pcgcctl.d32 = 0; ++ pcgcctl.b.extnd_hiber_switch = 1; ++ core_if->gr_backup->xhib_gpwrdn = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ core_if->gr_backup->xhib_pcgcctl = DWC_READ_REG32(core_if->pcgcctl) | pcgcctl.d32; ++ DWC_MODIFY_REG32(core_if->pcgcctl, 0, pcgcctl.d32); ++ ++ DWC_DEBUGPL(DBG_ANY, "Finished entering to extended hibernation\n"); ++ ++ return 1; ++ } ++ } ++ } else { ++ if (core_if->op_state == A_PERIPHERAL) { ++ DWC_DEBUGPL(DBG_ANY, "a_peripheral->a_host\n"); ++ /* Clear the a_peripheral flag, back to a_host. */ ++ DWC_SPINUNLOCK(core_if->lock); ++ cil_pcd_stop(core_if); ++ cil_hcd_start(core_if); ++ DWC_SPINLOCK(core_if->lock); ++ core_if->op_state = A_HOST; ++ } ++ } ++ ++ /* Change to L2(suspend) state */ ++ core_if->lx_state = DWC_OTG_L2; ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.usbsuspend = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ ++ return 1; ++} ++ ++static int32_t dwc_otg_handle_xhib_exit_intr(dwc_otg_core_if_t * core_if) ++{ ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ gahbcfg_data_t gahbcfg = {.d32 = 0 }; ++ ++ dwc_udelay(10); ++ ++ /* Program GPIO register while entering to xHib */ ++ DWC_WRITE_REG32(&core_if->core_global_regs->ggpio, 0x0); ++ ++ pcgcctl.d32 = core_if->gr_backup->xhib_pcgcctl; ++ pcgcctl.b.extnd_hiber_pwrclmp = 0; ++ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32); ++ dwc_udelay(10); ++ ++ gpwrdn.d32 = core_if->gr_backup->xhib_gpwrdn; ++ gpwrdn.b.restore = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ restore_lpm_i2c_regs(core_if); ++ ++ pcgcctl.d32 = core_if->gr_backup->pcgcctl_local & (0x3FFFF << 14); ++ pcgcctl.b.max_xcvrselect = 1; ++ pcgcctl.b.ess_reg_restored = 0; ++ pcgcctl.b.extnd_hiber_switch = 0; ++ pcgcctl.b.extnd_hiber_pwrclmp = 0; ++ pcgcctl.b.enbl_extnd_hiber = 1; ++ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32); ++ ++ gahbcfg.d32 = core_if->gr_backup->gahbcfg_local; ++ gahbcfg.b.glblintrmsk = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gahbcfg, gahbcfg.d32); ++ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, 0xFFFFFFFF); ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, 0x1 << 16); ++ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, ++ core_if->gr_backup->gusbcfg_local); ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg, ++ core_if->dr_backup->dcfg); ++ ++ pcgcctl.d32 = 0; ++ pcgcctl.d32 = core_if->gr_backup->pcgcctl_local & (0x3FFFF << 14); ++ pcgcctl.b.max_xcvrselect = 1; ++ pcgcctl.d32 |= 0x608; ++ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32); ++ dwc_udelay(10); ++ ++ pcgcctl.d32 = 0; ++ pcgcctl.d32 = core_if->gr_backup->pcgcctl_local & (0x3FFFF << 14); ++ pcgcctl.b.max_xcvrselect = 1; ++ pcgcctl.b.ess_reg_restored = 1; ++ pcgcctl.b.enbl_extnd_hiber = 1; ++ pcgcctl.b.rstpdwnmodule = 1; ++ pcgcctl.b.restoremode = 1; ++ DWC_WRITE_REG32(core_if->pcgcctl, pcgcctl.d32); ++ ++ DWC_DEBUGPL(DBG_ANY, "%s called\n", __FUNCTION__); ++ ++ return 1; ++} ++ ++#ifdef CONFIG_USB_DWC_OTG_LPM ++/** ++ * This function hadles LPM transaction received interrupt. ++ */ ++static int32_t dwc_otg_handle_lpm_intr(dwc_otg_core_if_t * core_if) ++{ ++ glpmcfg_data_t lpmcfg; ++ gintsts_data_t gintsts; ++ ++ if (!core_if->core_params->lpm_enable) { ++ DWC_PRINTF("Unexpected LPM interrupt\n"); ++ } ++ ++ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ DWC_PRINTF("LPM config register = 0x%08x\n", lpmcfg.d32); ++ ++ if (dwc_otg_is_host_mode(core_if)) { ++ cil_hcd_sleep(core_if); ++ } else { ++ lpmcfg.b.hird_thres |= (1 << 4); ++ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg, ++ lpmcfg.d32); ++ } ++ ++ /* Examine prt_sleep_sts after TL1TokenTetry period max (10 us) */ ++ dwc_udelay(10); ++ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ if (lpmcfg.b.prt_sleep_sts) { ++ /* Save the current state */ ++ core_if->lx_state = DWC_OTG_L1; ++ } ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.lpmtranrcvd = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ return 1; ++} ++#endif /* CONFIG_USB_DWC_OTG_LPM */ ++ ++/** ++ * This function returns the Core Interrupt register. ++ */ ++static inline uint32_t dwc_otg_read_common_intr(dwc_otg_core_if_t * core_if, gintmsk_data_t *reenable_gintmsk, dwc_otg_hcd_t *hcd) ++{ ++ gahbcfg_data_t gahbcfg = {.d32 = 0 }; ++ gintsts_data_t gintsts; ++ gintmsk_data_t gintmsk; ++ gintmsk_data_t gintmsk_common = {.d32 = 0 }; ++ gintmsk_common.b.wkupintr = 1; ++ gintmsk_common.b.sessreqintr = 1; ++ gintmsk_common.b.conidstschng = 1; ++ gintmsk_common.b.otgintr = 1; ++ gintmsk_common.b.modemismatch = 1; ++ gintmsk_common.b.disconnect = 1; ++ gintmsk_common.b.usbsuspend = 1; ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ gintmsk_common.b.lpmtranrcvd = 1; ++#endif ++ gintmsk_common.b.restoredone = 1; ++ if(dwc_otg_is_device_mode(core_if)) ++ { ++ /** @todo: The port interrupt occurs while in device ++ * mode. Added code to CIL to clear the interrupt for now! ++ */ ++ gintmsk_common.b.portintr = 1; ++ } ++ if(fiq_enable) { ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&hcd->fiq_state->lock); ++ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts); ++ gintmsk.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintmsk); ++ /* Pull in the interrupts that the FIQ has masked */ ++ gintmsk.d32 |= ~(hcd->fiq_state->gintmsk_saved.d32); ++ gintmsk.d32 |= gintmsk_common.d32; ++ /* for the upstairs function to reenable - have to read it here in case FIQ triggers again */ ++ reenable_gintmsk->d32 = gintmsk.d32; ++ fiq_fsm_spin_unlock(&hcd->fiq_state->lock); ++ local_fiq_enable(); ++ } else { ++ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts); ++ gintmsk.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintmsk); ++ } ++ ++ gahbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gahbcfg); ++ ++#ifdef DEBUG ++ /* if any common interrupts set */ ++ if (gintsts.d32 & gintmsk_common.d32) { ++ DWC_DEBUGPL(DBG_ANY, "common_intr: gintsts=%08x gintmsk=%08x\n", ++ gintsts.d32, gintmsk.d32); ++ } ++#endif ++ if (!fiq_enable){ ++ if (gahbcfg.b.glblintrmsk) ++ return ((gintsts.d32 & gintmsk.d32) & gintmsk_common.d32); ++ else ++ return 0; ++ } else { ++ /* Our IRQ kicker is no longer the USB hardware, it's the MPHI interface. ++ * Can't trust the global interrupt mask bit in this case. ++ */ ++ return ((gintsts.d32 & gintmsk.d32) & gintmsk_common.d32); ++ } ++ ++} ++ ++/* MACRO for clearing interupt bits in GPWRDN register */ ++#define CLEAR_GPWRDN_INTR(__core_if,__intr) \ ++do { \ ++ gpwrdn_data_t gpwrdn = {.d32=0}; \ ++ gpwrdn.b.__intr = 1; \ ++ DWC_MODIFY_REG32(&__core_if->core_global_regs->gpwrdn, \ ++ 0, gpwrdn.d32); \ ++} while (0) ++ ++/** ++ * Common interrupt handler. ++ * ++ * The common interrupts are those that occur in both Host and Device mode. ++ * This handler handles the following interrupts: ++ * - Mode Mismatch Interrupt ++ * - Disconnect Interrupt ++ * - OTG Interrupt ++ * - Connector ID Status Change Interrupt ++ * - Session Request Interrupt. ++ * - Resume / Remote Wakeup Detected Interrupt. ++ * - LPM Transaction Received Interrupt ++ * - ADP Transaction Received Interrupt ++ * ++ */ ++int32_t dwc_otg_handle_common_intr(void *dev) ++{ ++ int retval = 0; ++ gintsts_data_t gintsts; ++ gintmsk_data_t gintmsk_reenable = { .d32 = 0 }; ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ dwc_otg_device_t *otg_dev = dev; ++ dwc_otg_core_if_t *core_if = otg_dev->core_if; ++ gpwrdn.d32 = DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ if (dwc_otg_is_device_mode(core_if)) ++ core_if->frame_num = dwc_otg_get_frame_number(core_if); ++ ++ if (core_if->lock) ++ DWC_SPINLOCK(core_if->lock); ++ ++ if (core_if->power_down == 3 && core_if->xhib == 1) { ++ DWC_DEBUGPL(DBG_ANY, "Exiting from xHIB state\n"); ++ retval |= dwc_otg_handle_xhib_exit_intr(core_if); ++ core_if->xhib = 2; ++ if (core_if->lock) ++ DWC_SPINUNLOCK(core_if->lock); ++ ++ return retval; ++ } ++ ++ if (core_if->hibernation_suspend <= 0) { ++ /* read_common will have to poke the FIQ's saved mask. We must then clear this mask at the end ++ * of this handler - god only knows why it's done like this ++ */ ++ gintsts.d32 = dwc_otg_read_common_intr(core_if, &gintmsk_reenable, otg_dev->hcd); ++ ++ if (gintsts.b.modemismatch) { ++ retval |= dwc_otg_handle_mode_mismatch_intr(core_if); ++ } ++ if (gintsts.b.otgintr) { ++ retval |= dwc_otg_handle_otg_intr(core_if); ++ } ++ if (gintsts.b.conidstschng) { ++ retval |= ++ dwc_otg_handle_conn_id_status_change_intr(core_if); ++ } ++ if (gintsts.b.disconnect) { ++ retval |= dwc_otg_handle_disconnect_intr(core_if); ++ } ++ if (gintsts.b.sessreqintr) { ++ retval |= dwc_otg_handle_session_req_intr(core_if); ++ } ++ if (gintsts.b.wkupintr) { ++ retval |= dwc_otg_handle_wakeup_detected_intr(core_if); ++ } ++ if (gintsts.b.usbsuspend) { ++ retval |= dwc_otg_handle_usb_suspend_intr(core_if); ++ } ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ if (gintsts.b.lpmtranrcvd) { ++ retval |= dwc_otg_handle_lpm_intr(core_if); ++ } ++#endif ++ if (gintsts.b.restoredone) { ++ gintsts.d32 = 0; ++ if (core_if->power_down == 2) ++ core_if->hibernation_suspend = -1; ++ else if (core_if->power_down == 3 && core_if->xhib == 2) { ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ dctl_data_t dctl = {.d32 = 0 }; ++ ++ DWC_WRITE_REG32(&core_if->core_global_regs-> ++ gintsts, 0xFFFFFFFF); ++ ++ DWC_DEBUGPL(DBG_ANY, ++ "RESTORE DONE generated\n"); ++ ++ gpwrdn.b.restore = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ pcgcctl.b.rstpdwnmodule = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0); ++ ++ DWC_WRITE_REG32(&core_if->core_global_regs->gusbcfg, core_if->gr_backup->gusbcfg_local); ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dcfg, core_if->dr_backup->dcfg); ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl, core_if->dr_backup->dctl); ++ dwc_udelay(50); ++ ++ dctl.b.pwronprgdone = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0, dctl.d32); ++ dwc_udelay(10); ++ ++ dwc_otg_restore_global_regs(core_if); ++ dwc_otg_restore_dev_regs(core_if, 0); ++ ++ dctl.d32 = 0; ++ dctl.b.pwronprgdone = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32, 0); ++ dwc_udelay(10); ++ ++ pcgcctl.d32 = 0; ++ pcgcctl.b.enbl_extnd_hiber = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0); ++ ++ /* The core will be in ON STATE */ ++ core_if->lx_state = DWC_OTG_L0; ++ core_if->xhib = 0; ++ ++ DWC_SPINUNLOCK(core_if->lock); ++ if (core_if->pcd_cb && core_if->pcd_cb->resume_wakeup) { ++ core_if->pcd_cb->resume_wakeup(core_if->pcd_cb->p); ++ } ++ DWC_SPINLOCK(core_if->lock); ++ ++ } ++ ++ gintsts.b.restoredone = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts,gintsts.d32); ++ DWC_PRINTF(" --Restore done interrupt received-- \n"); ++ retval |= 1; ++ } ++ if (gintsts.b.portintr && dwc_otg_is_device_mode(core_if)) { ++ /* The port interrupt occurs while in device mode with HPRT0 ++ * Port Enable/Disable. ++ */ ++ gintsts.d32 = 0; ++ gintsts.b.portintr = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts,gintsts.d32); ++ retval |= 1; ++ gintmsk_reenable.b.portintr = 1; ++ ++ } ++ /* Did we actually handle anything? if so, unmask the interrupt */ ++// fiq_print(FIQDBG_INT, otg_dev->hcd->fiq_state, "CILOUT %1d", retval); ++// fiq_print(FIQDBG_INT, otg_dev->hcd->fiq_state, "%08x", gintsts.d32); ++// fiq_print(FIQDBG_INT, otg_dev->hcd->fiq_state, "%08x", gintmsk_reenable.d32); ++ if (retval && fiq_enable) { ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, gintmsk_reenable.d32); ++ } ++ ++ } else { ++ DWC_DEBUGPL(DBG_ANY, "gpwrdn=%08x\n", gpwrdn.d32); ++ ++ if (gpwrdn.b.disconn_det && gpwrdn.b.disconn_det_msk) { ++ CLEAR_GPWRDN_INTR(core_if, disconn_det); ++ if (gpwrdn.b.linestate == 0) { ++ dwc_otg_handle_pwrdn_disconnect_intr(core_if); ++ } else { ++ DWC_PRINTF("Disconnect detected while linestate is not 0\n"); ++ } ++ ++ retval |= 1; ++ } ++ if (gpwrdn.b.lnstschng && gpwrdn.b.lnstchng_msk) { ++ CLEAR_GPWRDN_INTR(core_if, lnstschng); ++ /* remote wakeup from hibernation */ ++ if (gpwrdn.b.linestate == 2 || gpwrdn.b.linestate == 1) { ++ dwc_otg_handle_pwrdn_wakeup_detected_intr(core_if); ++ } else { ++ DWC_PRINTF("gpwrdn.linestate = %d\n", gpwrdn.b.linestate); ++ } ++ retval |= 1; ++ } ++ if (gpwrdn.b.rst_det && gpwrdn.b.rst_det_msk) { ++ CLEAR_GPWRDN_INTR(core_if, rst_det); ++ if (gpwrdn.b.linestate == 0) { ++ DWC_PRINTF("Reset detected\n"); ++ retval |= dwc_otg_device_hibernation_restore(core_if, 0, 1); ++ } ++ } ++ if (gpwrdn.b.srp_det && gpwrdn.b.srp_det_msk) { ++ CLEAR_GPWRDN_INTR(core_if, srp_det); ++ dwc_otg_handle_pwrdn_srp_intr(core_if); ++ retval |= 1; ++ } ++ } ++ /* Handle ADP interrupt here */ ++ if (gpwrdn.b.adp_int) { ++ DWC_PRINTF("ADP interrupt\n"); ++ CLEAR_GPWRDN_INTR(core_if, adp_int); ++ dwc_otg_adp_handle_intr(core_if); ++ retval |= 1; ++ } ++ if (gpwrdn.b.sts_chngint && gpwrdn.b.sts_chngint_msk) { ++ DWC_PRINTF("STS CHNG interrupt asserted\n"); ++ CLEAR_GPWRDN_INTR(core_if, sts_chngint); ++ dwc_otg_handle_pwrdn_stschng_intr(otg_dev); ++ ++ retval |= 1; ++ } ++ if (core_if->lock) ++ DWC_SPINUNLOCK(core_if->lock); ++ return retval; ++} +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_core_if.h +@@ -0,0 +1,705 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_core_if.h $ ++ * $Revision: #13 $ ++ * $Date: 2012/08/10 $ ++ * $Change: 2047372 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++#if !defined(__DWC_CORE_IF_H__) ++#define __DWC_CORE_IF_H__ ++ ++#include "dwc_os.h" ++ ++/** @file ++ * This file defines DWC_OTG Core API ++ */ ++ ++struct dwc_otg_core_if; ++typedef struct dwc_otg_core_if dwc_otg_core_if_t; ++ ++/** Maximum number of Periodic FIFOs */ ++#define MAX_PERIO_FIFOS 15 ++/** Maximum number of Periodic FIFOs */ ++#define MAX_TX_FIFOS 15 ++ ++/** Maximum number of Endpoints/HostChannels */ ++#define MAX_EPS_CHANNELS 16 ++ ++extern dwc_otg_core_if_t *dwc_otg_cil_init(const uint32_t * _reg_base_addr); ++extern void dwc_otg_core_init(dwc_otg_core_if_t * _core_if); ++extern void dwc_otg_cil_remove(dwc_otg_core_if_t * _core_if); ++ ++extern void dwc_otg_enable_global_interrupts(dwc_otg_core_if_t * _core_if); ++extern void dwc_otg_disable_global_interrupts(dwc_otg_core_if_t * _core_if); ++ ++extern uint8_t dwc_otg_is_device_mode(dwc_otg_core_if_t * _core_if); ++extern uint8_t dwc_otg_is_host_mode(dwc_otg_core_if_t * _core_if); ++ ++extern uint8_t dwc_otg_is_dma_enable(dwc_otg_core_if_t * core_if); ++ ++/** This function should be called on every hardware interrupt. */ ++extern int32_t dwc_otg_handle_common_intr(void *otg_dev); ++ ++/** @name OTG Core Parameters */ ++/** @{ */ ++ ++/** ++ * Specifies the OTG capabilities. The driver will automatically ++ * detect the value for this parameter if none is specified. ++ * 0 - HNP and SRP capable (default) ++ * 1 - SRP Only capable ++ * 2 - No HNP/SRP capable ++ */ ++extern int dwc_otg_set_param_otg_cap(dwc_otg_core_if_t * core_if, int32_t val); ++extern int32_t dwc_otg_get_param_otg_cap(dwc_otg_core_if_t * core_if); ++#define DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE 0 ++#define DWC_OTG_CAP_PARAM_SRP_ONLY_CAPABLE 1 ++#define DWC_OTG_CAP_PARAM_NO_HNP_SRP_CAPABLE 2 ++#define dwc_param_otg_cap_default DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE ++ ++extern int dwc_otg_set_param_opt(dwc_otg_core_if_t * core_if, int32_t val); ++extern int32_t dwc_otg_get_param_opt(dwc_otg_core_if_t * core_if); ++#define dwc_param_opt_default 1 ++ ++/** ++ * Specifies whether to use slave or DMA mode for accessing the data ++ * FIFOs. The driver will automatically detect the value for this ++ * parameter if none is specified. ++ * 0 - Slave ++ * 1 - DMA (default, if available) ++ */ ++extern int dwc_otg_set_param_dma_enable(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_dma_enable(dwc_otg_core_if_t * core_if); ++#define dwc_param_dma_enable_default 1 ++ ++/** ++ * When DMA mode is enabled specifies whether to use ++ * address DMA or DMA Descritor mode for accessing the data ++ * FIFOs in device mode. The driver will automatically detect ++ * the value for this parameter if none is specified. ++ * 0 - address DMA ++ * 1 - DMA Descriptor(default, if available) ++ */ ++extern int dwc_otg_set_param_dma_desc_enable(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_dma_desc_enable(dwc_otg_core_if_t * core_if); ++//#define dwc_param_dma_desc_enable_default 1 ++#define dwc_param_dma_desc_enable_default 0 // Broadcom BCM2708 ++ ++/** The DMA Burst size (applicable only for External DMA ++ * Mode). 1, 4, 8 16, 32, 64, 128, 256 (default 32) ++ */ ++extern int dwc_otg_set_param_dma_burst_size(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_dma_burst_size(dwc_otg_core_if_t * core_if); ++#define dwc_param_dma_burst_size_default 32 ++ ++/** ++ * Specifies the maximum speed of operation in host and device mode. ++ * The actual speed depends on the speed of the attached device and ++ * the value of phy_type. The actual speed depends on the speed of the ++ * attached device. ++ * 0 - High Speed (default) ++ * 1 - Full Speed ++ */ ++extern int dwc_otg_set_param_speed(dwc_otg_core_if_t * core_if, int32_t val); ++extern int32_t dwc_otg_get_param_speed(dwc_otg_core_if_t * core_if); ++#define dwc_param_speed_default 0 ++#define DWC_SPEED_PARAM_HIGH 0 ++#define DWC_SPEED_PARAM_FULL 1 ++ ++/** Specifies whether low power mode is supported when attached ++ * to a Full Speed or Low Speed device in host mode. ++ * 0 - Don't support low power mode (default) ++ * 1 - Support low power mode ++ */ ++extern int dwc_otg_set_param_host_support_fs_ls_low_power(dwc_otg_core_if_t * ++ core_if, int32_t val); ++extern int32_t dwc_otg_get_param_host_support_fs_ls_low_power(dwc_otg_core_if_t ++ * core_if); ++#define dwc_param_host_support_fs_ls_low_power_default 0 ++ ++/** Specifies the PHY clock rate in low power mode when connected to a ++ * Low Speed device in host mode. This parameter is applicable only if ++ * HOST_SUPPORT_FS_LS_LOW_POWER is enabled. If PHY_TYPE is set to FS ++ * then defaults to 6 MHZ otherwise 48 MHZ. ++ * ++ * 0 - 48 MHz ++ * 1 - 6 MHz ++ */ ++extern int dwc_otg_set_param_host_ls_low_power_phy_clk(dwc_otg_core_if_t * ++ core_if, int32_t val); ++extern int32_t dwc_otg_get_param_host_ls_low_power_phy_clk(dwc_otg_core_if_t * ++ core_if); ++#define dwc_param_host_ls_low_power_phy_clk_default 0 ++#define DWC_HOST_LS_LOW_POWER_PHY_CLK_PARAM_48MHZ 0 ++#define DWC_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ 1 ++ ++/** ++ * 0 - Use cC FIFO size parameters ++ * 1 - Allow dynamic FIFO sizing (default) ++ */ ++extern int dwc_otg_set_param_enable_dynamic_fifo(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_enable_dynamic_fifo(dwc_otg_core_if_t * ++ core_if); ++#define dwc_param_enable_dynamic_fifo_default 1 ++ ++/** Total number of 4-byte words in the data FIFO memory. This ++ * memory includes the Rx FIFO, non-periodic Tx FIFO, and periodic ++ * Tx FIFOs. ++ * 32 to 32768 (default 8192) ++ * Note: The total FIFO memory depth in the FPGA configuration is 8192. ++ */ ++extern int dwc_otg_set_param_data_fifo_size(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_data_fifo_size(dwc_otg_core_if_t * core_if); ++//#define dwc_param_data_fifo_size_default 8192 ++#define dwc_param_data_fifo_size_default 0xFF0 // Broadcom BCM2708 ++ ++/** Number of 4-byte words in the Rx FIFO in device mode when dynamic ++ * FIFO sizing is enabled. ++ * 16 to 32768 (default 1064) ++ */ ++extern int dwc_otg_set_param_dev_rx_fifo_size(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_dev_rx_fifo_size(dwc_otg_core_if_t * core_if); ++#define dwc_param_dev_rx_fifo_size_default 1064 ++ ++/** Number of 4-byte words in the non-periodic Tx FIFO in device mode ++ * when dynamic FIFO sizing is enabled. ++ * 16 to 32768 (default 1024) ++ */ ++extern int dwc_otg_set_param_dev_nperio_tx_fifo_size(dwc_otg_core_if_t * ++ core_if, int32_t val); ++extern int32_t dwc_otg_get_param_dev_nperio_tx_fifo_size(dwc_otg_core_if_t * ++ core_if); ++#define dwc_param_dev_nperio_tx_fifo_size_default 1024 ++ ++/** Number of 4-byte words in each of the periodic Tx FIFOs in device ++ * mode when dynamic FIFO sizing is enabled. ++ * 4 to 768 (default 256) ++ */ ++extern int dwc_otg_set_param_dev_perio_tx_fifo_size(dwc_otg_core_if_t * core_if, ++ int32_t val, int fifo_num); ++extern int32_t dwc_otg_get_param_dev_perio_tx_fifo_size(dwc_otg_core_if_t * ++ core_if, int fifo_num); ++#define dwc_param_dev_perio_tx_fifo_size_default 256 ++ ++/** Number of 4-byte words in the Rx FIFO in host mode when dynamic ++ * FIFO sizing is enabled. ++ * 16 to 32768 (default 1024) ++ */ ++extern int dwc_otg_set_param_host_rx_fifo_size(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_host_rx_fifo_size(dwc_otg_core_if_t * core_if); ++//#define dwc_param_host_rx_fifo_size_default 1024 ++#define dwc_param_host_rx_fifo_size_default 774 // Broadcom BCM2708 ++ ++/** Number of 4-byte words in the non-periodic Tx FIFO in host mode ++ * when Dynamic FIFO sizing is enabled in the core. ++ * 16 to 32768 (default 1024) ++ */ ++extern int dwc_otg_set_param_host_nperio_tx_fifo_size(dwc_otg_core_if_t * ++ core_if, int32_t val); ++extern int32_t dwc_otg_get_param_host_nperio_tx_fifo_size(dwc_otg_core_if_t * ++ core_if); ++//#define dwc_param_host_nperio_tx_fifo_size_default 1024 ++#define dwc_param_host_nperio_tx_fifo_size_default 0x100 // Broadcom BCM2708 ++ ++/** Number of 4-byte words in the host periodic Tx FIFO when dynamic ++ * FIFO sizing is enabled. ++ * 16 to 32768 (default 1024) ++ */ ++extern int dwc_otg_set_param_host_perio_tx_fifo_size(dwc_otg_core_if_t * ++ core_if, int32_t val); ++extern int32_t dwc_otg_get_param_host_perio_tx_fifo_size(dwc_otg_core_if_t * ++ core_if); ++//#define dwc_param_host_perio_tx_fifo_size_default 1024 ++#define dwc_param_host_perio_tx_fifo_size_default 0x200 // Broadcom BCM2708 ++ ++/** The maximum transfer size supported in bytes. ++ * 2047 to 65,535 (default 65,535) ++ */ ++extern int dwc_otg_set_param_max_transfer_size(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_max_transfer_size(dwc_otg_core_if_t * core_if); ++#define dwc_param_max_transfer_size_default 65535 ++ ++/** The maximum number of packets in a transfer. ++ * 15 to 511 (default 511) ++ */ ++extern int dwc_otg_set_param_max_packet_count(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_max_packet_count(dwc_otg_core_if_t * core_if); ++#define dwc_param_max_packet_count_default 511 ++ ++/** The number of host channel registers to use. ++ * 1 to 16 (default 12) ++ * Note: The FPGA configuration supports a maximum of 12 host channels. ++ */ ++extern int dwc_otg_set_param_host_channels(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_host_channels(dwc_otg_core_if_t * core_if); ++//#define dwc_param_host_channels_default 12 ++#define dwc_param_host_channels_default 8 // Broadcom BCM2708 ++ ++/** The number of endpoints in addition to EP0 available for device ++ * mode operations. ++ * 1 to 15 (default 6 IN and OUT) ++ * Note: The FPGA configuration supports a maximum of 6 IN and OUT ++ * endpoints in addition to EP0. ++ */ ++extern int dwc_otg_set_param_dev_endpoints(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_dev_endpoints(dwc_otg_core_if_t * core_if); ++#define dwc_param_dev_endpoints_default 6 ++ ++/** ++ * Specifies the type of PHY interface to use. By default, the driver ++ * will automatically detect the phy_type. ++ * ++ * 0 - Full Speed PHY ++ * 1 - UTMI+ (default) ++ * 2 - ULPI ++ */ ++extern int dwc_otg_set_param_phy_type(dwc_otg_core_if_t * core_if, int32_t val); ++extern int32_t dwc_otg_get_param_phy_type(dwc_otg_core_if_t * core_if); ++#define DWC_PHY_TYPE_PARAM_FS 0 ++#define DWC_PHY_TYPE_PARAM_UTMI 1 ++#define DWC_PHY_TYPE_PARAM_ULPI 2 ++#define dwc_param_phy_type_default DWC_PHY_TYPE_PARAM_UTMI ++ ++/** ++ * Specifies the UTMI+ Data Width. This parameter is ++ * applicable for a PHY_TYPE of UTMI+ or ULPI. (For a ULPI ++ * PHY_TYPE, this parameter indicates the data width between ++ * the MAC and the ULPI Wrapper.) Also, this parameter is ++ * applicable only if the OTG_HSPHY_WIDTH cC parameter was set ++ * to "8 and 16 bits", meaning that the core has been ++ * configured to work at either data path width. ++ * ++ * 8 or 16 bits (default 16) ++ */ ++extern int dwc_otg_set_param_phy_utmi_width(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_phy_utmi_width(dwc_otg_core_if_t * core_if); ++//#define dwc_param_phy_utmi_width_default 16 ++#define dwc_param_phy_utmi_width_default 8 // Broadcom BCM2708 ++ ++/** ++ * Specifies whether the ULPI operates at double or single ++ * data rate. This parameter is only applicable if PHY_TYPE is ++ * ULPI. ++ * ++ * 0 - single data rate ULPI interface with 8 bit wide data ++ * bus (default) ++ * 1 - double data rate ULPI interface with 4 bit wide data ++ * bus ++ */ ++extern int dwc_otg_set_param_phy_ulpi_ddr(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_phy_ulpi_ddr(dwc_otg_core_if_t * core_if); ++#define dwc_param_phy_ulpi_ddr_default 0 ++ ++/** ++ * Specifies whether to use the internal or external supply to ++ * drive the vbus with a ULPI phy. ++ */ ++extern int dwc_otg_set_param_phy_ulpi_ext_vbus(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_phy_ulpi_ext_vbus(dwc_otg_core_if_t * core_if); ++#define DWC_PHY_ULPI_INTERNAL_VBUS 0 ++#define DWC_PHY_ULPI_EXTERNAL_VBUS 1 ++#define dwc_param_phy_ulpi_ext_vbus_default DWC_PHY_ULPI_INTERNAL_VBUS ++ ++/** ++ * Specifies whether to use the I2Cinterface for full speed PHY. This ++ * parameter is only applicable if PHY_TYPE is FS. ++ * 0 - No (default) ++ * 1 - Yes ++ */ ++extern int dwc_otg_set_param_i2c_enable(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_i2c_enable(dwc_otg_core_if_t * core_if); ++#define dwc_param_i2c_enable_default 0 ++ ++extern int dwc_otg_set_param_ulpi_fs_ls(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_ulpi_fs_ls(dwc_otg_core_if_t * core_if); ++#define dwc_param_ulpi_fs_ls_default 0 ++ ++extern int dwc_otg_set_param_ts_dline(dwc_otg_core_if_t * core_if, int32_t val); ++extern int32_t dwc_otg_get_param_ts_dline(dwc_otg_core_if_t * core_if); ++#define dwc_param_ts_dline_default 0 ++ ++/** ++ * Specifies whether dedicated transmit FIFOs are ++ * enabled for non periodic IN endpoints in device mode ++ * 0 - No ++ * 1 - Yes ++ */ ++extern int dwc_otg_set_param_en_multiple_tx_fifo(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_en_multiple_tx_fifo(dwc_otg_core_if_t * ++ core_if); ++#define dwc_param_en_multiple_tx_fifo_default 1 ++ ++/** Number of 4-byte words in each of the Tx FIFOs in device ++ * mode when dynamic FIFO sizing is enabled. ++ * 4 to 768 (default 256) ++ */ ++extern int dwc_otg_set_param_dev_tx_fifo_size(dwc_otg_core_if_t * core_if, ++ int fifo_num, int32_t val); ++extern int32_t dwc_otg_get_param_dev_tx_fifo_size(dwc_otg_core_if_t * core_if, ++ int fifo_num); ++#define dwc_param_dev_tx_fifo_size_default 768 ++ ++/** Thresholding enable flag- ++ * bit 0 - enable non-ISO Tx thresholding ++ * bit 1 - enable ISO Tx thresholding ++ * bit 2 - enable Rx thresholding ++ */ ++extern int dwc_otg_set_param_thr_ctl(dwc_otg_core_if_t * core_if, int32_t val); ++extern int32_t dwc_otg_get_thr_ctl(dwc_otg_core_if_t * core_if, int fifo_num); ++#define dwc_param_thr_ctl_default 0 ++ ++/** Thresholding length for Tx ++ * FIFOs in 32 bit DWORDs ++ */ ++extern int dwc_otg_set_param_tx_thr_length(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_tx_thr_length(dwc_otg_core_if_t * core_if); ++#define dwc_param_tx_thr_length_default 64 ++ ++/** Thresholding length for Rx ++ * FIFOs in 32 bit DWORDs ++ */ ++extern int dwc_otg_set_param_rx_thr_length(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_rx_thr_length(dwc_otg_core_if_t * core_if); ++#define dwc_param_rx_thr_length_default 64 ++ ++/** ++ * Specifies whether LPM (Link Power Management) support is enabled ++ */ ++extern int dwc_otg_set_param_lpm_enable(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_lpm_enable(dwc_otg_core_if_t * core_if); ++#define dwc_param_lpm_enable_default 1 ++ ++/** ++ * Specifies whether PTI enhancement is enabled ++ */ ++extern int dwc_otg_set_param_pti_enable(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_pti_enable(dwc_otg_core_if_t * core_if); ++#define dwc_param_pti_enable_default 0 ++ ++/** ++ * Specifies whether MPI enhancement is enabled ++ */ ++extern int dwc_otg_set_param_mpi_enable(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_mpi_enable(dwc_otg_core_if_t * core_if); ++#define dwc_param_mpi_enable_default 0 ++ ++/** ++ * Specifies whether ADP capability is enabled ++ */ ++extern int dwc_otg_set_param_adp_enable(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_adp_enable(dwc_otg_core_if_t * core_if); ++#define dwc_param_adp_enable_default 0 ++ ++/** ++ * Specifies whether IC_USB capability is enabled ++ */ ++ ++extern int dwc_otg_set_param_ic_usb_cap(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_ic_usb_cap(dwc_otg_core_if_t * core_if); ++#define dwc_param_ic_usb_cap_default 0 ++ ++extern int dwc_otg_set_param_ahb_thr_ratio(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_ahb_thr_ratio(dwc_otg_core_if_t * core_if); ++#define dwc_param_ahb_thr_ratio_default 0 ++ ++extern int dwc_otg_set_param_power_down(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_power_down(dwc_otg_core_if_t * core_if); ++#define dwc_param_power_down_default 0 ++ ++extern int dwc_otg_set_param_reload_ctl(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_reload_ctl(dwc_otg_core_if_t * core_if); ++#define dwc_param_reload_ctl_default 0 ++ ++extern int dwc_otg_set_param_dev_out_nak(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_dev_out_nak(dwc_otg_core_if_t * core_if); ++#define dwc_param_dev_out_nak_default 0 ++ ++extern int dwc_otg_set_param_cont_on_bna(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_cont_on_bna(dwc_otg_core_if_t * core_if); ++#define dwc_param_cont_on_bna_default 0 ++ ++extern int dwc_otg_set_param_ahb_single(dwc_otg_core_if_t * core_if, ++ int32_t val); ++extern int32_t dwc_otg_get_param_ahb_single(dwc_otg_core_if_t * core_if); ++#define dwc_param_ahb_single_default 0 ++ ++extern int dwc_otg_set_param_otg_ver(dwc_otg_core_if_t * core_if, int32_t val); ++extern int32_t dwc_otg_get_param_otg_ver(dwc_otg_core_if_t * core_if); ++#define dwc_param_otg_ver_default 0 ++ ++/** @} */ ++ ++/** @name Access to registers and bit-fields */ ++ ++/** ++ * Dump core registers and SPRAM ++ */ ++extern void dwc_otg_dump_dev_registers(dwc_otg_core_if_t * _core_if); ++extern void dwc_otg_dump_spram(dwc_otg_core_if_t * _core_if); ++extern void dwc_otg_dump_host_registers(dwc_otg_core_if_t * _core_if); ++extern void dwc_otg_dump_global_registers(dwc_otg_core_if_t * _core_if); ++ ++/** ++ * Get host negotiation status. ++ */ ++extern uint32_t dwc_otg_get_hnpstatus(dwc_otg_core_if_t * core_if); ++ ++/** ++ * Get srp status ++ */ ++extern uint32_t dwc_otg_get_srpstatus(dwc_otg_core_if_t * core_if); ++ ++/** ++ * Set hnpreq bit in the GOTGCTL register. ++ */ ++extern void dwc_otg_set_hnpreq(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * Get Content of SNPSID register. ++ */ ++extern uint32_t dwc_otg_get_gsnpsid(dwc_otg_core_if_t * core_if); ++ ++/** ++ * Get current mode. ++ * Returns 0 if in device mode, and 1 if in host mode. ++ */ ++extern uint32_t dwc_otg_get_mode(dwc_otg_core_if_t * core_if); ++ ++/** ++ * Get value of hnpcapable field in the GUSBCFG register ++ */ ++extern uint32_t dwc_otg_get_hnpcapable(dwc_otg_core_if_t * core_if); ++/** ++ * Set value of hnpcapable field in the GUSBCFG register ++ */ ++extern void dwc_otg_set_hnpcapable(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * Get value of srpcapable field in the GUSBCFG register ++ */ ++extern uint32_t dwc_otg_get_srpcapable(dwc_otg_core_if_t * core_if); ++/** ++ * Set value of srpcapable field in the GUSBCFG register ++ */ ++extern void dwc_otg_set_srpcapable(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * Get value of devspeed field in the DCFG register ++ */ ++extern uint32_t dwc_otg_get_devspeed(dwc_otg_core_if_t * core_if); ++/** ++ * Set value of devspeed field in the DCFG register ++ */ ++extern void dwc_otg_set_devspeed(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * Get the value of busconnected field from the HPRT0 register ++ */ ++extern uint32_t dwc_otg_get_busconnected(dwc_otg_core_if_t * core_if); ++ ++/** ++ * Gets the device enumeration Speed. ++ */ ++extern uint32_t dwc_otg_get_enumspeed(dwc_otg_core_if_t * core_if); ++ ++/** ++ * Get value of prtpwr field from the HPRT0 register ++ */ ++extern uint32_t dwc_otg_get_prtpower(dwc_otg_core_if_t * core_if); ++ ++/** ++ * Get value of flag indicating core state - hibernated or not ++ */ ++extern uint32_t dwc_otg_get_core_state(dwc_otg_core_if_t * core_if); ++ ++/** ++ * Set value of prtpwr field from the HPRT0 register ++ */ ++extern void dwc_otg_set_prtpower(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * Get value of prtsusp field from the HPRT0 regsiter ++ */ ++extern uint32_t dwc_otg_get_prtsuspend(dwc_otg_core_if_t * core_if); ++/** ++ * Set value of prtpwr field from the HPRT0 register ++ */ ++extern void dwc_otg_set_prtsuspend(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * Get value of ModeChTimEn field from the HCFG regsiter ++ */ ++extern uint32_t dwc_otg_get_mode_ch_tim(dwc_otg_core_if_t * core_if); ++/** ++ * Set value of ModeChTimEn field from the HCFG regsiter ++ */ ++extern void dwc_otg_set_mode_ch_tim(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * Get value of Fram Interval field from the HFIR regsiter ++ */ ++extern uint32_t dwc_otg_get_fr_interval(dwc_otg_core_if_t * core_if); ++/** ++ * Set value of Frame Interval field from the HFIR regsiter ++ */ ++extern void dwc_otg_set_fr_interval(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * Set value of prtres field from the HPRT0 register ++ *FIXME Remove? ++ */ ++extern void dwc_otg_set_prtresume(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * Get value of rmtwkupsig bit in DCTL register ++ */ ++extern uint32_t dwc_otg_get_remotewakesig(dwc_otg_core_if_t * core_if); ++ ++/** ++ * Get value of prt_sleep_sts field from the GLPMCFG register ++ */ ++extern uint32_t dwc_otg_get_lpm_portsleepstatus(dwc_otg_core_if_t * core_if); ++ ++/** ++ * Get value of rem_wkup_en field from the GLPMCFG register ++ */ ++extern uint32_t dwc_otg_get_lpm_remotewakeenabled(dwc_otg_core_if_t * core_if); ++ ++/** ++ * Get value of appl_resp field from the GLPMCFG register ++ */ ++extern uint32_t dwc_otg_get_lpmresponse(dwc_otg_core_if_t * core_if); ++/** ++ * Set value of appl_resp field from the GLPMCFG register ++ */ ++extern void dwc_otg_set_lpmresponse(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * Get value of hsic_connect field from the GLPMCFG register ++ */ ++extern uint32_t dwc_otg_get_hsic_connect(dwc_otg_core_if_t * core_if); ++/** ++ * Set value of hsic_connect field from the GLPMCFG register ++ */ ++extern void dwc_otg_set_hsic_connect(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * Get value of inv_sel_hsic field from the GLPMCFG register. ++ */ ++extern uint32_t dwc_otg_get_inv_sel_hsic(dwc_otg_core_if_t * core_if); ++/** ++ * Set value of inv_sel_hsic field from the GLPMFG register. ++ */ ++extern void dwc_otg_set_inv_sel_hsic(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/* ++ * Some functions for accessing registers ++ */ ++ ++/** ++ * GOTGCTL register ++ */ ++extern uint32_t dwc_otg_get_gotgctl(dwc_otg_core_if_t * core_if); ++extern void dwc_otg_set_gotgctl(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * GUSBCFG register ++ */ ++extern uint32_t dwc_otg_get_gusbcfg(dwc_otg_core_if_t * core_if); ++extern void dwc_otg_set_gusbcfg(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * GRXFSIZ register ++ */ ++extern uint32_t dwc_otg_get_grxfsiz(dwc_otg_core_if_t * core_if); ++extern void dwc_otg_set_grxfsiz(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * GNPTXFSIZ register ++ */ ++extern uint32_t dwc_otg_get_gnptxfsiz(dwc_otg_core_if_t * core_if); ++extern void dwc_otg_set_gnptxfsiz(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++extern uint32_t dwc_otg_get_gpvndctl(dwc_otg_core_if_t * core_if); ++extern void dwc_otg_set_gpvndctl(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * GGPIO register ++ */ ++extern uint32_t dwc_otg_get_ggpio(dwc_otg_core_if_t * core_if); ++extern void dwc_otg_set_ggpio(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * GUID register ++ */ ++extern uint32_t dwc_otg_get_guid(dwc_otg_core_if_t * core_if); ++extern void dwc_otg_set_guid(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * HPRT0 register ++ */ ++extern uint32_t dwc_otg_get_hprt0(dwc_otg_core_if_t * core_if); ++extern void dwc_otg_set_hprt0(dwc_otg_core_if_t * core_if, uint32_t val); ++ ++/** ++ * GHPTXFSIZE ++ */ ++extern uint32_t dwc_otg_get_hptxfsiz(dwc_otg_core_if_t * core_if); ++ ++/** @} */ ++ ++#endif /* __DWC_CORE_IF_H__ */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_dbg.h +@@ -0,0 +1,117 @@ ++/* ========================================================================== ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++#ifndef __DWC_OTG_DBG_H__ ++#define __DWC_OTG_DBG_H__ ++ ++/** @file ++ * This file defines debug levels. ++ * Debugging support vanishes in non-debug builds. ++ */ ++ ++/** ++ * The Debug Level bit-mask variable. ++ */ ++extern uint32_t g_dbg_lvl; ++/** ++ * Set the Debug Level variable. ++ */ ++static inline uint32_t SET_DEBUG_LEVEL(const uint32_t new) ++{ ++ uint32_t old = g_dbg_lvl; ++ g_dbg_lvl = new; ++ return old; ++} ++ ++#define DBG_USER (0x1) ++/** When debug level has the DBG_CIL bit set, display CIL Debug messages. */ ++#define DBG_CIL (0x2) ++/** When debug level has the DBG_CILV bit set, display CIL Verbose debug ++ * messages */ ++#define DBG_CILV (0x20) ++/** When debug level has the DBG_PCD bit set, display PCD (Device) debug ++ * messages */ ++#define DBG_PCD (0x4) ++/** When debug level has the DBG_PCDV set, display PCD (Device) Verbose debug ++ * messages */ ++#define DBG_PCDV (0x40) ++/** When debug level has the DBG_HCD bit set, display Host debug messages */ ++#define DBG_HCD (0x8) ++/** When debug level has the DBG_HCDV bit set, display Verbose Host debug ++ * messages */ ++#define DBG_HCDV (0x80) ++/** When debug level has the DBG_HCD_URB bit set, display enqueued URBs in host ++ * mode. */ ++#define DBG_HCD_URB (0x800) ++/** When debug level has the DBG_HCDI bit set, display host interrupt ++ * messages. */ ++#define DBG_HCDI (0x1000) ++ ++/** When debug level has any bit set, display debug messages */ ++#define DBG_ANY (0xFF) ++ ++/** All debug messages off */ ++#define DBG_OFF 0 ++ ++/** Prefix string for DWC_DEBUG print macros. */ ++#define USB_DWC "DWC_otg: " ++ ++/** ++ * Print a debug message when the Global debug level variable contains ++ * the bit defined in lvl. ++ * ++ * @param[in] lvl - Debug level, use one of the DBG_ constants above. ++ * @param[in] x - like printf ++ * ++ * Example:

++ * ++ * DWC_DEBUGPL( DBG_ANY, "%s(%p)\n", __func__, _reg_base_addr); ++ * ++ *
++ * results in:
++ * ++ * usb-DWC_otg: dwc_otg_cil_init(ca867000) ++ * ++ */ ++#ifdef DEBUG ++ ++# define DWC_DEBUGPL(lvl, x...) do{ if ((lvl)&g_dbg_lvl)__DWC_DEBUG(USB_DWC x ); }while(0) ++# define DWC_DEBUGP(x...) DWC_DEBUGPL(DBG_ANY, x ) ++ ++# define CHK_DEBUG_LEVEL(level) ((level) & g_dbg_lvl) ++ ++#else ++ ++# define DWC_DEBUGPL(lvl, x...) do{}while(0) ++# define DWC_DEBUGP(x...) ++ ++# define CHK_DEBUG_LEVEL(level) (0) ++ ++#endif /*DEBUG*/ ++#endif +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_driver.c +@@ -0,0 +1,1772 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_driver.c $ ++ * $Revision: #92 $ ++ * $Date: 2012/08/10 $ ++ * $Change: 2047372 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++/** @file ++ * The dwc_otg_driver module provides the initialization and cleanup entry ++ * points for the DWC_otg driver. This module will be dynamically installed ++ * after Linux is booted using the insmod command. When the module is ++ * installed, the dwc_otg_driver_init function is called. When the module is ++ * removed (using rmmod), the dwc_otg_driver_cleanup function is called. ++ * ++ * This module also defines a data structure for the dwc_otg_driver, which is ++ * used in conjunction with the standard ARM lm_device structure. These ++ * structures allow the OTG driver to comply with the standard Linux driver ++ * model in which devices and drivers are registered with a bus driver. This ++ * has the benefit that Linux can expose attributes of the driver and device ++ * in its special sysfs file system. Users can then read or write files in ++ * this file system to perform diagnostics on the driver components or the ++ * device. ++ */ ++ ++#include "dwc_otg_os_dep.h" ++#include "dwc_os.h" ++#include "dwc_otg_dbg.h" ++#include "dwc_otg_driver.h" ++#include "dwc_otg_attr.h" ++#include "dwc_otg_core_if.h" ++#include "dwc_otg_pcd_if.h" ++#include "dwc_otg_hcd_if.h" ++#include "dwc_otg_fiq_fsm.h" ++ ++#define DWC_DRIVER_VERSION "3.00a 10-AUG-2012" ++#define DWC_DRIVER_DESC "HS OTG USB Controller driver" ++ ++bool microframe_schedule=true; ++ ++static const char dwc_driver_name[] = "dwc_otg"; ++ ++ ++extern int pcd_init( ++#ifdef LM_INTERFACE ++ struct lm_device *_dev ++#elif defined(PCI_INTERFACE) ++ struct pci_dev *_dev ++#elif defined(PLATFORM_INTERFACE) ++ struct platform_device *dev ++#endif ++ ); ++extern int hcd_init( ++#ifdef LM_INTERFACE ++ struct lm_device *_dev ++#elif defined(PCI_INTERFACE) ++ struct pci_dev *_dev ++#elif defined(PLATFORM_INTERFACE) ++ struct platform_device *dev ++#endif ++ ); ++ ++extern int pcd_remove( ++#ifdef LM_INTERFACE ++ struct lm_device *_dev ++#elif defined(PCI_INTERFACE) ++ struct pci_dev *_dev ++#elif defined(PLATFORM_INTERFACE) ++ struct platform_device *_dev ++#endif ++ ); ++ ++extern void hcd_remove( ++#ifdef LM_INTERFACE ++ struct lm_device *_dev ++#elif defined(PCI_INTERFACE) ++ struct pci_dev *_dev ++#elif defined(PLATFORM_INTERFACE) ++ struct platform_device *_dev ++#endif ++ ); ++ ++extern void dwc_otg_adp_start(dwc_otg_core_if_t * core_if, uint8_t is_host); ++ ++/*-------------------------------------------------------------------------*/ ++/* Encapsulate the module parameter settings */ ++ ++struct dwc_otg_driver_module_params { ++ int32_t opt; ++ int32_t otg_cap; ++ int32_t dma_enable; ++ int32_t dma_desc_enable; ++ int32_t dma_burst_size; ++ int32_t speed; ++ int32_t host_support_fs_ls_low_power; ++ int32_t host_ls_low_power_phy_clk; ++ int32_t enable_dynamic_fifo; ++ int32_t data_fifo_size; ++ int32_t dev_rx_fifo_size; ++ int32_t dev_nperio_tx_fifo_size; ++ uint32_t dev_perio_tx_fifo_size[MAX_PERIO_FIFOS]; ++ int32_t host_rx_fifo_size; ++ int32_t host_nperio_tx_fifo_size; ++ int32_t host_perio_tx_fifo_size; ++ int32_t max_transfer_size; ++ int32_t max_packet_count; ++ int32_t host_channels; ++ int32_t dev_endpoints; ++ int32_t phy_type; ++ int32_t phy_utmi_width; ++ int32_t phy_ulpi_ddr; ++ int32_t phy_ulpi_ext_vbus; ++ int32_t i2c_enable; ++ int32_t ulpi_fs_ls; ++ int32_t ts_dline; ++ int32_t en_multiple_tx_fifo; ++ uint32_t dev_tx_fifo_size[MAX_TX_FIFOS]; ++ uint32_t thr_ctl; ++ uint32_t tx_thr_length; ++ uint32_t rx_thr_length; ++ int32_t pti_enable; ++ int32_t mpi_enable; ++ int32_t lpm_enable; ++ int32_t ic_usb_cap; ++ int32_t ahb_thr_ratio; ++ int32_t power_down; ++ int32_t reload_ctl; ++ int32_t dev_out_nak; ++ int32_t cont_on_bna; ++ int32_t ahb_single; ++ int32_t otg_ver; ++ int32_t adp_enable; ++}; ++ ++static struct dwc_otg_driver_module_params dwc_otg_module_params = { ++ .opt = -1, ++ .otg_cap = -1, ++ .dma_enable = -1, ++ .dma_desc_enable = -1, ++ .dma_burst_size = -1, ++ .speed = -1, ++ .host_support_fs_ls_low_power = -1, ++ .host_ls_low_power_phy_clk = -1, ++ .enable_dynamic_fifo = -1, ++ .data_fifo_size = -1, ++ .dev_rx_fifo_size = -1, ++ .dev_nperio_tx_fifo_size = -1, ++ .dev_perio_tx_fifo_size = { ++ /* dev_perio_tx_fifo_size_1 */ ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1 ++ /* 15 */ ++ }, ++ .host_rx_fifo_size = -1, ++ .host_nperio_tx_fifo_size = -1, ++ .host_perio_tx_fifo_size = -1, ++ .max_transfer_size = -1, ++ .max_packet_count = -1, ++ .host_channels = -1, ++ .dev_endpoints = -1, ++ .phy_type = -1, ++ .phy_utmi_width = -1, ++ .phy_ulpi_ddr = -1, ++ .phy_ulpi_ext_vbus = -1, ++ .i2c_enable = -1, ++ .ulpi_fs_ls = -1, ++ .ts_dline = -1, ++ .en_multiple_tx_fifo = -1, ++ .dev_tx_fifo_size = { ++ /* dev_tx_fifo_size */ ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1, ++ -1 ++ /* 15 */ ++ }, ++ .thr_ctl = -1, ++ .tx_thr_length = -1, ++ .rx_thr_length = -1, ++ .pti_enable = -1, ++ .mpi_enable = -1, ++ .lpm_enable = 0, ++ .ic_usb_cap = -1, ++ .ahb_thr_ratio = -1, ++ .power_down = -1, ++ .reload_ctl = -1, ++ .dev_out_nak = -1, ++ .cont_on_bna = -1, ++ .ahb_single = -1, ++ .otg_ver = -1, ++ .adp_enable = -1, ++}; ++ ++//Global variable to switch the fiq fix on or off ++bool fiq_enable = 1; ++// Global variable to enable the split transaction fix ++bool fiq_fsm_enable = true; ++//Bulk split-transaction NAK holdoff in microframes ++uint16_t nak_holdoff = 8; ++ ++//Force host mode during CIL re-init ++bool cil_force_host = true; ++ ++unsigned short fiq_fsm_mask = 0x0F; ++ ++unsigned short int_ep_interval_min = 0; ++/** ++ * This function shows the Driver Version. ++ */ ++static ssize_t version_show(struct device_driver *dev, char *buf) ++{ ++ return snprintf(buf, sizeof(DWC_DRIVER_VERSION) + 2, "%s\n", ++ DWC_DRIVER_VERSION); ++} ++ ++static DRIVER_ATTR_RO(version); ++ ++/** ++ * Global Debug Level Mask. ++ */ ++uint32_t g_dbg_lvl = 0; /* OFF */ ++ ++/** ++ * This function shows the driver Debug Level. ++ */ ++static ssize_t debuglevel_show(struct device_driver *drv, char *buf) ++{ ++ return sprintf(buf, "0x%0x\n", g_dbg_lvl); ++} ++ ++/** ++ * This function stores the driver Debug Level. ++ */ ++static ssize_t debuglevel_store(struct device_driver *drv, const char *buf, ++ size_t count) ++{ ++ g_dbg_lvl = simple_strtoul(buf, NULL, 16); ++ return count; ++} ++ ++static DRIVER_ATTR_RW(debuglevel); ++ ++/** ++ * This function is called during module intialization ++ * to pass module parameters to the DWC_OTG CORE. ++ */ ++static int set_parameters(dwc_otg_core_if_t * core_if) ++{ ++ int retval = 0; ++ int i; ++ ++ if (dwc_otg_module_params.otg_cap != -1) { ++ retval += ++ dwc_otg_set_param_otg_cap(core_if, ++ dwc_otg_module_params.otg_cap); ++ } ++ if (dwc_otg_module_params.dma_enable != -1) { ++ retval += ++ dwc_otg_set_param_dma_enable(core_if, ++ dwc_otg_module_params. ++ dma_enable); ++ } ++ if (dwc_otg_module_params.dma_desc_enable != -1) { ++ retval += ++ dwc_otg_set_param_dma_desc_enable(core_if, ++ dwc_otg_module_params. ++ dma_desc_enable); ++ } ++ if (dwc_otg_module_params.opt != -1) { ++ retval += ++ dwc_otg_set_param_opt(core_if, dwc_otg_module_params.opt); ++ } ++ if (dwc_otg_module_params.dma_burst_size != -1) { ++ retval += ++ dwc_otg_set_param_dma_burst_size(core_if, ++ dwc_otg_module_params. ++ dma_burst_size); ++ } ++ if (dwc_otg_module_params.host_support_fs_ls_low_power != -1) { ++ retval += ++ dwc_otg_set_param_host_support_fs_ls_low_power(core_if, ++ dwc_otg_module_params. ++ host_support_fs_ls_low_power); ++ } ++ if (dwc_otg_module_params.enable_dynamic_fifo != -1) { ++ retval += ++ dwc_otg_set_param_enable_dynamic_fifo(core_if, ++ dwc_otg_module_params. ++ enable_dynamic_fifo); ++ } ++ if (dwc_otg_module_params.data_fifo_size != -1) { ++ retval += ++ dwc_otg_set_param_data_fifo_size(core_if, ++ dwc_otg_module_params. ++ data_fifo_size); ++ } ++ if (dwc_otg_module_params.dev_rx_fifo_size != -1) { ++ retval += ++ dwc_otg_set_param_dev_rx_fifo_size(core_if, ++ dwc_otg_module_params. ++ dev_rx_fifo_size); ++ } ++ if (dwc_otg_module_params.dev_nperio_tx_fifo_size != -1) { ++ retval += ++ dwc_otg_set_param_dev_nperio_tx_fifo_size(core_if, ++ dwc_otg_module_params. ++ dev_nperio_tx_fifo_size); ++ } ++ if (dwc_otg_module_params.host_rx_fifo_size != -1) { ++ retval += ++ dwc_otg_set_param_host_rx_fifo_size(core_if, ++ dwc_otg_module_params.host_rx_fifo_size); ++ } ++ if (dwc_otg_module_params.host_nperio_tx_fifo_size != -1) { ++ retval += ++ dwc_otg_set_param_host_nperio_tx_fifo_size(core_if, ++ dwc_otg_module_params. ++ host_nperio_tx_fifo_size); ++ } ++ if (dwc_otg_module_params.host_perio_tx_fifo_size != -1) { ++ retval += ++ dwc_otg_set_param_host_perio_tx_fifo_size(core_if, ++ dwc_otg_module_params. ++ host_perio_tx_fifo_size); ++ } ++ if (dwc_otg_module_params.max_transfer_size != -1) { ++ retval += ++ dwc_otg_set_param_max_transfer_size(core_if, ++ dwc_otg_module_params. ++ max_transfer_size); ++ } ++ if (dwc_otg_module_params.max_packet_count != -1) { ++ retval += ++ dwc_otg_set_param_max_packet_count(core_if, ++ dwc_otg_module_params. ++ max_packet_count); ++ } ++ if (dwc_otg_module_params.host_channels != -1) { ++ retval += ++ dwc_otg_set_param_host_channels(core_if, ++ dwc_otg_module_params. ++ host_channels); ++ } ++ if (dwc_otg_module_params.dev_endpoints != -1) { ++ retval += ++ dwc_otg_set_param_dev_endpoints(core_if, ++ dwc_otg_module_params. ++ dev_endpoints); ++ } ++ if (dwc_otg_module_params.phy_type != -1) { ++ retval += ++ dwc_otg_set_param_phy_type(core_if, ++ dwc_otg_module_params.phy_type); ++ } ++ if (dwc_otg_module_params.speed != -1) { ++ retval += ++ dwc_otg_set_param_speed(core_if, ++ dwc_otg_module_params.speed); ++ } ++ if (dwc_otg_module_params.host_ls_low_power_phy_clk != -1) { ++ retval += ++ dwc_otg_set_param_host_ls_low_power_phy_clk(core_if, ++ dwc_otg_module_params. ++ host_ls_low_power_phy_clk); ++ } ++ if (dwc_otg_module_params.phy_ulpi_ddr != -1) { ++ retval += ++ dwc_otg_set_param_phy_ulpi_ddr(core_if, ++ dwc_otg_module_params. ++ phy_ulpi_ddr); ++ } ++ if (dwc_otg_module_params.phy_ulpi_ext_vbus != -1) { ++ retval += ++ dwc_otg_set_param_phy_ulpi_ext_vbus(core_if, ++ dwc_otg_module_params. ++ phy_ulpi_ext_vbus); ++ } ++ if (dwc_otg_module_params.phy_utmi_width != -1) { ++ retval += ++ dwc_otg_set_param_phy_utmi_width(core_if, ++ dwc_otg_module_params. ++ phy_utmi_width); ++ } ++ if (dwc_otg_module_params.ulpi_fs_ls != -1) { ++ retval += ++ dwc_otg_set_param_ulpi_fs_ls(core_if, ++ dwc_otg_module_params.ulpi_fs_ls); ++ } ++ if (dwc_otg_module_params.ts_dline != -1) { ++ retval += ++ dwc_otg_set_param_ts_dline(core_if, ++ dwc_otg_module_params.ts_dline); ++ } ++ if (dwc_otg_module_params.i2c_enable != -1) { ++ retval += ++ dwc_otg_set_param_i2c_enable(core_if, ++ dwc_otg_module_params. ++ i2c_enable); ++ } ++ if (dwc_otg_module_params.en_multiple_tx_fifo != -1) { ++ retval += ++ dwc_otg_set_param_en_multiple_tx_fifo(core_if, ++ dwc_otg_module_params. ++ en_multiple_tx_fifo); ++ } ++ for (i = 0; i < 15; i++) { ++ if (dwc_otg_module_params.dev_perio_tx_fifo_size[i] != -1) { ++ retval += ++ dwc_otg_set_param_dev_perio_tx_fifo_size(core_if, ++ dwc_otg_module_params. ++ dev_perio_tx_fifo_size ++ [i], i); ++ } ++ } ++ ++ for (i = 0; i < 15; i++) { ++ if (dwc_otg_module_params.dev_tx_fifo_size[i] != -1) { ++ retval += dwc_otg_set_param_dev_tx_fifo_size(core_if, ++ dwc_otg_module_params. ++ dev_tx_fifo_size ++ [i], i); ++ } ++ } ++ if (dwc_otg_module_params.thr_ctl != -1) { ++ retval += ++ dwc_otg_set_param_thr_ctl(core_if, ++ dwc_otg_module_params.thr_ctl); ++ } ++ if (dwc_otg_module_params.mpi_enable != -1) { ++ retval += ++ dwc_otg_set_param_mpi_enable(core_if, ++ dwc_otg_module_params. ++ mpi_enable); ++ } ++ if (dwc_otg_module_params.pti_enable != -1) { ++ retval += ++ dwc_otg_set_param_pti_enable(core_if, ++ dwc_otg_module_params. ++ pti_enable); ++ } ++ if (dwc_otg_module_params.lpm_enable != -1) { ++ retval += ++ dwc_otg_set_param_lpm_enable(core_if, ++ dwc_otg_module_params. ++ lpm_enable); ++ } ++ if (dwc_otg_module_params.ic_usb_cap != -1) { ++ retval += ++ dwc_otg_set_param_ic_usb_cap(core_if, ++ dwc_otg_module_params. ++ ic_usb_cap); ++ } ++ if (dwc_otg_module_params.tx_thr_length != -1) { ++ retval += ++ dwc_otg_set_param_tx_thr_length(core_if, ++ dwc_otg_module_params.tx_thr_length); ++ } ++ if (dwc_otg_module_params.rx_thr_length != -1) { ++ retval += ++ dwc_otg_set_param_rx_thr_length(core_if, ++ dwc_otg_module_params. ++ rx_thr_length); ++ } ++ if (dwc_otg_module_params.ahb_thr_ratio != -1) { ++ retval += ++ dwc_otg_set_param_ahb_thr_ratio(core_if, ++ dwc_otg_module_params.ahb_thr_ratio); ++ } ++ if (dwc_otg_module_params.power_down != -1) { ++ retval += ++ dwc_otg_set_param_power_down(core_if, ++ dwc_otg_module_params.power_down); ++ } ++ if (dwc_otg_module_params.reload_ctl != -1) { ++ retval += ++ dwc_otg_set_param_reload_ctl(core_if, ++ dwc_otg_module_params.reload_ctl); ++ } ++ ++ if (dwc_otg_module_params.dev_out_nak != -1) { ++ retval += ++ dwc_otg_set_param_dev_out_nak(core_if, ++ dwc_otg_module_params.dev_out_nak); ++ } ++ ++ if (dwc_otg_module_params.cont_on_bna != -1) { ++ retval += ++ dwc_otg_set_param_cont_on_bna(core_if, ++ dwc_otg_module_params.cont_on_bna); ++ } ++ ++ if (dwc_otg_module_params.ahb_single != -1) { ++ retval += ++ dwc_otg_set_param_ahb_single(core_if, ++ dwc_otg_module_params.ahb_single); ++ } ++ ++ if (dwc_otg_module_params.otg_ver != -1) { ++ retval += ++ dwc_otg_set_param_otg_ver(core_if, ++ dwc_otg_module_params.otg_ver); ++ } ++ if (dwc_otg_module_params.adp_enable != -1) { ++ retval += ++ dwc_otg_set_param_adp_enable(core_if, ++ dwc_otg_module_params. ++ adp_enable); ++ } ++ return retval; ++} ++ ++/** ++ * This function is the top level interrupt handler for the Common ++ * (Device and host modes) interrupts. ++ */ ++static irqreturn_t dwc_otg_common_irq(int irq, void *dev) ++{ ++ int32_t retval = IRQ_NONE; ++ ++ retval = dwc_otg_handle_common_intr(dev); ++ if (retval != 0) { ++ S3C2410X_CLEAR_EINTPEND(); ++ } ++ return IRQ_RETVAL(retval); ++} ++ ++/** ++ * This function is called when a lm_device is unregistered with the ++ * dwc_otg_driver. This happens, for example, when the rmmod command is ++ * executed. The device may or may not be electrically present. If it is ++ * present, the driver stops device processing. Any resources used on behalf ++ * of this device are freed. ++ * ++ * @param _dev ++ */ ++#ifdef LM_INTERFACE ++#define REM_RETVAL(n) ++static void dwc_otg_driver_remove( struct lm_device *_dev ) ++{ dwc_otg_device_t *otg_dev = lm_get_drvdata(_dev); ++#elif defined(PCI_INTERFACE) ++#define REM_RETVAL(n) ++static void dwc_otg_driver_remove( struct pci_dev *_dev ) ++{ dwc_otg_device_t *otg_dev = pci_get_drvdata(_dev); ++#elif defined(PLATFORM_INTERFACE) ++#define REM_RETVAL(n) n ++static int dwc_otg_driver_remove( struct platform_device *_dev ) ++{ dwc_otg_device_t *otg_dev = platform_get_drvdata(_dev); ++#endif ++ ++ DWC_DEBUGPL(DBG_ANY, "%s(%p) otg_dev %p\n", __func__, _dev, otg_dev); ++ ++ if (!otg_dev) { ++ /* Memory allocation for the dwc_otg_device failed. */ ++ DWC_DEBUGPL(DBG_ANY, "%s: otg_dev NULL!\n", __func__); ++ return REM_RETVAL(-ENOMEM); ++ } ++#ifndef DWC_DEVICE_ONLY ++ if (otg_dev->hcd) { ++ hcd_remove(_dev); ++ } else { ++ DWC_DEBUGPL(DBG_ANY, "%s: otg_dev->hcd NULL!\n", __func__); ++ return REM_RETVAL(-EINVAL); ++ } ++#endif ++ ++#ifndef DWC_HOST_ONLY ++ if (otg_dev->pcd) { ++ pcd_remove(_dev); ++ } else { ++ DWC_DEBUGPL(DBG_ANY, "%s: otg_dev->pcd NULL!\n", __func__); ++ return REM_RETVAL(-EINVAL); ++ } ++#endif ++ /* ++ * Free the IRQ ++ */ ++ if (otg_dev->common_irq_installed) { ++ free_irq(otg_dev->os_dep.irq_num, otg_dev); ++ } else { ++ DWC_DEBUGPL(DBG_ANY, "%s: There is no installed irq!\n", __func__); ++ return REM_RETVAL(-ENXIO); ++ } ++ ++ if (otg_dev->core_if) { ++ dwc_otg_cil_remove(otg_dev->core_if); ++ } else { ++ DWC_DEBUGPL(DBG_ANY, "%s: otg_dev->core_if NULL!\n", __func__); ++ return REM_RETVAL(-ENXIO); ++ } ++ ++ /* ++ * Remove the device attributes ++ */ ++ dwc_otg_attr_remove(_dev); ++ ++ /* ++ * Return the memory. ++ */ ++ if (otg_dev->os_dep.base) { ++ iounmap(otg_dev->os_dep.base); ++ } ++ DWC_FREE(otg_dev); ++ ++ /* ++ * Clear the drvdata pointer. ++ */ ++#ifdef LM_INTERFACE ++ lm_set_drvdata(_dev, 0); ++#elif defined(PCI_INTERFACE) ++ release_mem_region(otg_dev->os_dep.rsrc_start, ++ otg_dev->os_dep.rsrc_len); ++ pci_set_drvdata(_dev, 0); ++#elif defined(PLATFORM_INTERFACE) ++ platform_set_drvdata(_dev, 0); ++#endif ++ return REM_RETVAL(0); ++} ++ ++/** ++ * This function is called when an lm_device is bound to a ++ * dwc_otg_driver. It creates the driver components required to ++ * control the device (CIL, HCD, and PCD) and it initializes the ++ * device. The driver components are stored in a dwc_otg_device ++ * structure. A reference to the dwc_otg_device is saved in the ++ * lm_device. This allows the driver to access the dwc_otg_device ++ * structure on subsequent calls to driver methods for this device. ++ * ++ * @param _dev Bus device ++ */ ++static int dwc_otg_driver_probe( ++#ifdef LM_INTERFACE ++ struct lm_device *_dev ++#elif defined(PCI_INTERFACE) ++ struct pci_dev *_dev, ++ const struct pci_device_id *id ++#elif defined(PLATFORM_INTERFACE) ++ struct platform_device *_dev ++#endif ++ ) ++{ ++ int retval = 0; ++ dwc_otg_device_t *dwc_otg_device; ++ int devirq; ++ ++ dev_dbg(&_dev->dev, "dwc_otg_driver_probe(%p)\n", _dev); ++#ifdef LM_INTERFACE ++ dev_dbg(&_dev->dev, "start=0x%08x\n", (unsigned)_dev->resource.start); ++#elif defined(PCI_INTERFACE) ++ if (!id) { ++ DWC_ERROR("Invalid pci_device_id %p", id); ++ return -EINVAL; ++ } ++ ++ if (!_dev || (pci_enable_device(_dev) < 0)) { ++ DWC_ERROR("Invalid pci_device %p", _dev); ++ return -ENODEV; ++ } ++ dev_dbg(&_dev->dev, "start=0x%08x\n", (unsigned)pci_resource_start(_dev,0)); ++ /* other stuff needed as well? */ ++ ++#elif defined(PLATFORM_INTERFACE) ++ dev_dbg(&_dev->dev, "start=0x%08x (len 0x%x)\n", ++ (unsigned)_dev->resource->start, ++ (unsigned)(_dev->resource->end - _dev->resource->start)); ++#endif ++ ++ dwc_otg_device = DWC_ALLOC(sizeof(dwc_otg_device_t)); ++ ++ if (!dwc_otg_device) { ++ dev_err(&_dev->dev, "kmalloc of dwc_otg_device failed\n"); ++ return -ENOMEM; ++ } ++ ++ memset(dwc_otg_device, 0, sizeof(*dwc_otg_device)); ++ dwc_otg_device->os_dep.reg_offset = 0xFFFFFFFF; ++ dwc_otg_device->os_dep.platformdev = _dev; ++ ++ /* ++ * Map the DWC_otg Core memory into virtual address space. ++ */ ++#ifdef LM_INTERFACE ++ dwc_otg_device->os_dep.base = ioremap(_dev->resource.start, SZ_256K); ++ ++ if (!dwc_otg_device->os_dep.base) { ++ dev_err(&_dev->dev, "ioremap() failed\n"); ++ DWC_FREE(dwc_otg_device); ++ return -ENOMEM; ++ } ++ dev_dbg(&_dev->dev, "base=0x%08x\n", ++ (unsigned)dwc_otg_device->os_dep.base); ++#elif defined(PCI_INTERFACE) ++ _dev->current_state = PCI_D0; ++ _dev->dev.power.power_state = PMSG_ON; ++ ++ if (!_dev->irq) { ++ DWC_ERROR("Found HC with no IRQ. Check BIOS/PCI %s setup!", ++ pci_name(_dev)); ++ iounmap(dwc_otg_device->os_dep.base); ++ DWC_FREE(dwc_otg_device); ++ return -ENODEV; ++ } ++ ++ dwc_otg_device->os_dep.rsrc_start = pci_resource_start(_dev, 0); ++ dwc_otg_device->os_dep.rsrc_len = pci_resource_len(_dev, 0); ++ DWC_DEBUGPL(DBG_ANY, "PCI resource: start=%08x, len=%08x\n", ++ (unsigned)dwc_otg_device->os_dep.rsrc_start, ++ (unsigned)dwc_otg_device->os_dep.rsrc_len); ++ if (!request_mem_region ++ (dwc_otg_device->os_dep.rsrc_start, dwc_otg_device->os_dep.rsrc_len, ++ "dwc_otg")) { ++ dev_dbg(&_dev->dev, "error requesting memory\n"); ++ iounmap(dwc_otg_device->os_dep.base); ++ DWC_FREE(dwc_otg_device); ++ return -EFAULT; ++ } ++ ++ dwc_otg_device->os_dep.base = ++ ioremap(dwc_otg_device->os_dep.rsrc_start, ++ dwc_otg_device->os_dep.rsrc_len); ++ if (dwc_otg_device->os_dep.base == NULL) { ++ dev_dbg(&_dev->dev, "error mapping memory\n"); ++ release_mem_region(dwc_otg_device->os_dep.rsrc_start, ++ dwc_otg_device->os_dep.rsrc_len); ++ iounmap(dwc_otg_device->os_dep.base); ++ DWC_FREE(dwc_otg_device); ++ return -EFAULT; ++ } ++ dev_dbg(&_dev->dev, "base=0x%p (before adjust) \n", ++ dwc_otg_device->os_dep.base); ++ dwc_otg_device->os_dep.base = (char *)dwc_otg_device->os_dep.base; ++ dev_dbg(&_dev->dev, "base=0x%p (after adjust) \n", ++ dwc_otg_device->os_dep.base); ++ dev_dbg(&_dev->dev, "%s: mapped PA 0x%x to VA 0x%p\n", __func__, ++ (unsigned)dwc_otg_device->os_dep.rsrc_start, ++ dwc_otg_device->os_dep.base); ++ ++ pci_set_master(_dev); ++ pci_set_drvdata(_dev, dwc_otg_device); ++#elif defined(PLATFORM_INTERFACE) ++ DWC_DEBUGPL(DBG_ANY,"Platform resource: start=%08x, len=%08x\n", ++ _dev->resource->start, ++ _dev->resource->end - _dev->resource->start + 1); ++#if 1 ++ if (!request_mem_region(_dev->resource[0].start, ++ _dev->resource[0].end - _dev->resource[0].start + 1, ++ "dwc_otg")) { ++ dev_dbg(&_dev->dev, "error reserving mapped memory\n"); ++ retval = -EFAULT; ++ goto fail; ++ } ++ ++ dwc_otg_device->os_dep.base = ioremap(_dev->resource[0].start, ++ _dev->resource[0].end - ++ _dev->resource[0].start+1); ++ if (fiq_enable) ++ { ++ if (!request_mem_region(_dev->resource[1].start, ++ _dev->resource[1].end - _dev->resource[1].start + 1, ++ "dwc_otg")) { ++ dev_dbg(&_dev->dev, "error reserving mapped memory\n"); ++ retval = -EFAULT; ++ goto fail; ++ } ++ ++ dwc_otg_device->os_dep.mphi_base = ioremap(_dev->resource[1].start, ++ _dev->resource[1].end - ++ _dev->resource[1].start + 1); ++ dwc_otg_device->os_dep.use_swirq = (_dev->resource[1].end - _dev->resource[1].start) == 0x200; ++ } ++ ++#else ++ { ++ struct map_desc desc = { ++ .virtual = IO_ADDRESS((unsigned)_dev->resource->start), ++ .pfn = __phys_to_pfn((unsigned)_dev->resource->start), ++ .length = SZ_128K, ++ .type = MT_DEVICE ++ }; ++ iotable_init(&desc, 1); ++ dwc_otg_device->os_dep.base = (void *)desc.virtual; ++ } ++#endif ++ if (!dwc_otg_device->os_dep.base) { ++ dev_err(&_dev->dev, "ioremap() failed\n"); ++ retval = -ENOMEM; ++ goto fail; ++ } ++#endif ++ ++ /* ++ * Initialize driver data to point to the global DWC_otg ++ * Device structure. ++ */ ++#ifdef LM_INTERFACE ++ lm_set_drvdata(_dev, dwc_otg_device); ++#elif defined(PLATFORM_INTERFACE) ++ platform_set_drvdata(_dev, dwc_otg_device); ++#endif ++ dev_dbg(&_dev->dev, "dwc_otg_device=0x%p\n", dwc_otg_device); ++ ++ dwc_otg_device->core_if = dwc_otg_cil_init(dwc_otg_device->os_dep.base); ++ DWC_DEBUGPL(DBG_HCDV, "probe of device %p given core_if %p\n", ++ dwc_otg_device, dwc_otg_device->core_if);//GRAYG ++ ++ if (!dwc_otg_device->core_if) { ++ dev_err(&_dev->dev, "CIL initialization failed!\n"); ++ retval = -ENOMEM; ++ goto fail; ++ } ++ ++ dev_dbg(&_dev->dev, "Calling get_gsnpsid\n"); ++ /* ++ * Attempt to ensure this device is really a DWC_otg Controller. ++ * Read and verify the SNPSID register contents. The value should be ++ * 0x45F42XXX or 0x45F42XXX, which corresponds to either "OT2" or "OTG3", ++ * as in "OTG version 2.XX" or "OTG version 3.XX". ++ */ ++ ++ if (((dwc_otg_get_gsnpsid(dwc_otg_device->core_if) & 0xFFFFF000) != 0x4F542000) && ++ ((dwc_otg_get_gsnpsid(dwc_otg_device->core_if) & 0xFFFFF000) != 0x4F543000)) { ++ dev_err(&_dev->dev, "Bad value for SNPSID: 0x%08x\n", ++ dwc_otg_get_gsnpsid(dwc_otg_device->core_if)); ++ retval = -EINVAL; ++ goto fail; ++ } ++ ++ /* ++ * Validate parameter values. ++ */ ++ dev_dbg(&_dev->dev, "Calling set_parameters\n"); ++ if (set_parameters(dwc_otg_device->core_if)) { ++ retval = -EINVAL; ++ goto fail; ++ } ++ ++ /* ++ * Create Device Attributes in sysfs ++ */ ++ dev_dbg(&_dev->dev, "Calling attr_create\n"); ++ dwc_otg_attr_create(_dev); ++ ++ /* ++ * Disable the global interrupt until all the interrupt ++ * handlers are installed. ++ */ ++ dev_dbg(&_dev->dev, "Calling disable_global_interrupts\n"); ++ dwc_otg_disable_global_interrupts(dwc_otg_device->core_if); ++ ++ /* ++ * Install the interrupt handler for the common interrupts before ++ * enabling common interrupts in core_init below. ++ */ ++ ++#if defined(PLATFORM_INTERFACE) ++ devirq = platform_get_irq_byname(_dev, fiq_enable ? "soft" : "usb"); ++ if (devirq < 0) ++ devirq = platform_get_irq(_dev, fiq_enable ? 0 : 1); ++#else ++ devirq = _dev->irq; ++#endif ++ DWC_DEBUGPL(DBG_CIL, "registering (common) handler for irq%d\n", ++ devirq); ++ dev_dbg(&_dev->dev, "Calling request_irq(%d)\n", devirq); ++ retval = request_irq(devirq, dwc_otg_common_irq, ++ IRQF_SHARED, ++ "dwc_otg", dwc_otg_device); ++ if (retval) { ++ DWC_ERROR("request of irq%d failed\n", devirq); ++ retval = -EBUSY; ++ goto fail; ++ } else { ++ dwc_otg_device->common_irq_installed = 1; ++ } ++ dwc_otg_device->os_dep.irq_num = devirq; ++ dwc_otg_device->os_dep.fiq_num = -EINVAL; ++ if (fiq_enable) { ++ int devfiq = platform_get_irq_byname(_dev, "usb"); ++ if (devfiq < 0) ++ devfiq = platform_get_irq(_dev, 1); ++ dwc_otg_device->os_dep.fiq_num = devfiq; ++ } ++ ++#ifndef IRQF_TRIGGER_LOW ++#if defined(LM_INTERFACE) || defined(PLATFORM_INTERFACE) ++ dev_dbg(&_dev->dev, "Calling set_irq_type\n"); ++ set_irq_type(devirq, ++#if (LINUX_VERSION_CODE < KERNEL_VERSION(2,6,30)) ++ IRQT_LOW ++#else ++ IRQ_TYPE_LEVEL_LOW ++#endif ++ ); ++#endif ++#endif /*IRQF_TRIGGER_LOW*/ ++ ++ /* ++ * Initialize the DWC_otg core. ++ */ ++ dev_dbg(&_dev->dev, "Calling dwc_otg_core_init\n"); ++ dwc_otg_core_init(dwc_otg_device->core_if); ++ ++#ifndef DWC_HOST_ONLY ++ /* ++ * Initialize the PCD ++ */ ++ dev_dbg(&_dev->dev, "Calling pcd_init\n"); ++ retval = pcd_init(_dev); ++ if (retval != 0) { ++ DWC_ERROR("pcd_init failed\n"); ++ dwc_otg_device->pcd = NULL; ++ goto fail; ++ } ++#endif ++#ifndef DWC_DEVICE_ONLY ++ /* ++ * Initialize the HCD ++ */ ++ dev_dbg(&_dev->dev, "Calling hcd_init\n"); ++ retval = hcd_init(_dev); ++ if (retval != 0) { ++ DWC_ERROR("hcd_init failed\n"); ++ dwc_otg_device->hcd = NULL; ++ goto fail; ++ } ++#endif ++ /* Recover from drvdata having been overwritten by hcd_init() */ ++#ifdef LM_INTERFACE ++ lm_set_drvdata(_dev, dwc_otg_device); ++#elif defined(PLATFORM_INTERFACE) ++ platform_set_drvdata(_dev, dwc_otg_device); ++#elif defined(PCI_INTERFACE) ++ pci_set_drvdata(_dev, dwc_otg_device); ++ dwc_otg_device->os_dep.pcidev = _dev; ++#endif ++ ++ /* ++ * Enable the global interrupt after all the interrupt ++ * handlers are installed if there is no ADP support else ++ * perform initial actions required for Internal ADP logic. ++ */ ++ if (!dwc_otg_get_param_adp_enable(dwc_otg_device->core_if)) { ++ dev_dbg(&_dev->dev, "Calling enable_global_interrupts\n"); ++ dwc_otg_enable_global_interrupts(dwc_otg_device->core_if); ++ dev_dbg(&_dev->dev, "Done\n"); ++ } else ++ dwc_otg_adp_start(dwc_otg_device->core_if, ++ dwc_otg_is_host_mode(dwc_otg_device->core_if)); ++ ++ return 0; ++ ++fail: ++ dwc_otg_driver_remove(_dev); ++ return retval; ++} ++ ++/** ++ * This structure defines the methods to be called by a bus driver ++ * during the lifecycle of a device on that bus. Both drivers and ++ * devices are registered with a bus driver. The bus driver matches ++ * devices to drivers based on information in the device and driver ++ * structures. ++ * ++ * The probe function is called when the bus driver matches a device ++ * to this driver. The remove function is called when a device is ++ * unregistered with the bus driver. ++ */ ++#ifdef LM_INTERFACE ++static struct lm_driver dwc_otg_driver = { ++ .drv = {.name = (char *)dwc_driver_name,}, ++ .probe = dwc_otg_driver_probe, ++ .remove = dwc_otg_driver_remove, ++ // 'suspend' and 'resume' absent ++}; ++#elif defined(PCI_INTERFACE) ++static const struct pci_device_id pci_ids[] = { { ++ PCI_DEVICE(0x16c3, 0xabcd), ++ .driver_data = ++ (unsigned long)0xdeadbeef, ++ }, { /* end: all zeroes */ } ++}; ++ ++MODULE_DEVICE_TABLE(pci, pci_ids); ++ ++/* pci driver glue; this is a "new style" PCI driver module */ ++static struct pci_driver dwc_otg_driver = { ++ .name = "dwc_otg", ++ .id_table = pci_ids, ++ ++ .probe = dwc_otg_driver_probe, ++ .remove = dwc_otg_driver_remove, ++ ++ .driver = { ++ .name = (char *)dwc_driver_name, ++ }, ++}; ++#elif defined(PLATFORM_INTERFACE) ++static struct platform_device_id platform_ids[] = { ++ { ++ .name = "bcm2708_usb", ++ .driver_data = (kernel_ulong_t) 0xdeadbeef, ++ }, ++ { /* end: all zeroes */ } ++}; ++MODULE_DEVICE_TABLE(platform, platform_ids); ++ ++static const struct of_device_id dwc_otg_of_match_table[] = { ++ { .compatible = "brcm,bcm2708-usb", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, dwc_otg_of_match_table); ++ ++static struct platform_driver dwc_otg_driver = { ++ .driver = { ++ .name = (char *)dwc_driver_name, ++ .of_match_table = dwc_otg_of_match_table, ++ }, ++ .id_table = platform_ids, ++ ++ .probe = dwc_otg_driver_probe, ++ .remove = dwc_otg_driver_remove, ++ // no 'shutdown', 'suspend', 'resume', 'suspend_late' or 'resume_early' ++}; ++#endif ++ ++/** ++ * This function is called when the dwc_otg_driver is installed with the ++ * insmod command. It registers the dwc_otg_driver structure with the ++ * appropriate bus driver. This will cause the dwc_otg_driver_probe function ++ * to be called. In addition, the bus driver will automatically expose ++ * attributes defined for the device and driver in the special sysfs file ++ * system. ++ * ++ * @return ++ */ ++static int __init dwc_otg_driver_init(void) ++{ ++ int retval = 0; ++ int error; ++ struct device_driver *drv; ++ ++ if(fiq_fsm_enable && !fiq_enable) { ++ printk(KERN_WARNING "dwc_otg: fiq_fsm_enable was set without fiq_enable! Correcting.\n"); ++ fiq_enable = 1; ++ } ++ ++ printk(KERN_INFO "%s: version %s (%s bus)\n", dwc_driver_name, ++ DWC_DRIVER_VERSION, ++#ifdef LM_INTERFACE ++ "logicmodule"); ++ retval = lm_driver_register(&dwc_otg_driver); ++ drv = &dwc_otg_driver.drv; ++#elif defined(PCI_INTERFACE) ++ "pci"); ++ retval = pci_register_driver(&dwc_otg_driver); ++ drv = &dwc_otg_driver.driver; ++#elif defined(PLATFORM_INTERFACE) ++ "platform"); ++ retval = platform_driver_register(&dwc_otg_driver); ++ drv = &dwc_otg_driver.driver; ++#endif ++ if (retval < 0) { ++ printk(KERN_ERR "%s retval=%d\n", __func__, retval); ++ return retval; ++ } ++ printk(KERN_DEBUG "dwc_otg: FIQ %s\n", fiq_enable ? "enabled":"disabled"); ++ printk(KERN_DEBUG "dwc_otg: NAK holdoff %s\n", nak_holdoff ? "enabled":"disabled"); ++ printk(KERN_DEBUG "dwc_otg: FIQ split-transaction FSM %s\n", fiq_fsm_enable ? "enabled":"disabled"); ++ ++ error = driver_create_file(drv, &driver_attr_version); ++#ifdef DEBUG ++ error = driver_create_file(drv, &driver_attr_debuglevel); ++#endif ++ return retval; ++} ++ ++module_init(dwc_otg_driver_init); ++ ++/** ++ * This function is called when the driver is removed from the kernel ++ * with the rmmod command. The driver unregisters itself with its bus ++ * driver. ++ * ++ */ ++static void __exit dwc_otg_driver_cleanup(void) ++{ ++ printk(KERN_DEBUG "dwc_otg_driver_cleanup()\n"); ++ ++#ifdef LM_INTERFACE ++ driver_remove_file(&dwc_otg_driver.drv, &driver_attr_debuglevel); ++ driver_remove_file(&dwc_otg_driver.drv, &driver_attr_version); ++ lm_driver_unregister(&dwc_otg_driver); ++#elif defined(PCI_INTERFACE) ++ driver_remove_file(&dwc_otg_driver.driver, &driver_attr_debuglevel); ++ driver_remove_file(&dwc_otg_driver.driver, &driver_attr_version); ++ pci_unregister_driver(&dwc_otg_driver); ++#elif defined(PLATFORM_INTERFACE) ++ driver_remove_file(&dwc_otg_driver.driver, &driver_attr_debuglevel); ++ driver_remove_file(&dwc_otg_driver.driver, &driver_attr_version); ++ platform_driver_unregister(&dwc_otg_driver); ++#endif ++ ++ printk(KERN_INFO "%s module removed\n", dwc_driver_name); ++} ++ ++module_exit(dwc_otg_driver_cleanup); ++ ++MODULE_DESCRIPTION(DWC_DRIVER_DESC); ++MODULE_AUTHOR("Synopsys Inc."); ++MODULE_LICENSE("GPL"); ++ ++module_param_named(otg_cap, dwc_otg_module_params.otg_cap, int, 0444); ++MODULE_PARM_DESC(otg_cap, "OTG Capabilities 0=HNP&SRP 1=SRP Only 2=None"); ++module_param_named(opt, dwc_otg_module_params.opt, int, 0444); ++MODULE_PARM_DESC(opt, "OPT Mode"); ++module_param_named(dma_enable, dwc_otg_module_params.dma_enable, int, 0444); ++MODULE_PARM_DESC(dma_enable, "DMA Mode 0=Slave 1=DMA enabled"); ++ ++module_param_named(dma_desc_enable, dwc_otg_module_params.dma_desc_enable, int, ++ 0444); ++MODULE_PARM_DESC(dma_desc_enable, ++ "DMA Desc Mode 0=Address DMA 1=DMA Descriptor enabled"); ++ ++module_param_named(dma_burst_size, dwc_otg_module_params.dma_burst_size, int, ++ 0444); ++MODULE_PARM_DESC(dma_burst_size, ++ "DMA Burst Size 1, 4, 8, 16, 32, 64, 128, 256"); ++module_param_named(speed, dwc_otg_module_params.speed, int, 0444); ++MODULE_PARM_DESC(speed, "Speed 0=High Speed 1=Full Speed"); ++module_param_named(host_support_fs_ls_low_power, ++ dwc_otg_module_params.host_support_fs_ls_low_power, int, ++ 0444); ++MODULE_PARM_DESC(host_support_fs_ls_low_power, ++ "Support Low Power w/FS or LS 0=Support 1=Don't Support"); ++module_param_named(host_ls_low_power_phy_clk, ++ dwc_otg_module_params.host_ls_low_power_phy_clk, int, 0444); ++MODULE_PARM_DESC(host_ls_low_power_phy_clk, ++ "Low Speed Low Power Clock 0=48Mhz 1=6Mhz"); ++module_param_named(enable_dynamic_fifo, ++ dwc_otg_module_params.enable_dynamic_fifo, int, 0444); ++MODULE_PARM_DESC(enable_dynamic_fifo, "0=cC Setting 1=Allow Dynamic Sizing"); ++module_param_named(data_fifo_size, dwc_otg_module_params.data_fifo_size, int, ++ 0444); ++MODULE_PARM_DESC(data_fifo_size, ++ "Total number of words in the data FIFO memory 32-32768"); ++module_param_named(dev_rx_fifo_size, dwc_otg_module_params.dev_rx_fifo_size, ++ int, 0444); ++MODULE_PARM_DESC(dev_rx_fifo_size, "Number of words in the Rx FIFO 16-32768"); ++module_param_named(dev_nperio_tx_fifo_size, ++ dwc_otg_module_params.dev_nperio_tx_fifo_size, int, 0444); ++MODULE_PARM_DESC(dev_nperio_tx_fifo_size, ++ "Number of words in the non-periodic Tx FIFO 16-32768"); ++module_param_named(dev_perio_tx_fifo_size_1, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[0], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_1, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_2, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[1], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_2, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_3, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[2], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_3, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_4, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[3], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_4, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_5, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[4], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_5, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_6, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[5], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_6, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_7, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[6], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_7, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_8, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[7], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_8, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_9, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[8], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_9, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_10, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[9], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_10, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_11, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[10], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_11, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_12, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[11], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_12, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_13, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[12], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_13, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_14, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[13], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_14, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(dev_perio_tx_fifo_size_15, ++ dwc_otg_module_params.dev_perio_tx_fifo_size[14], int, 0444); ++MODULE_PARM_DESC(dev_perio_tx_fifo_size_15, ++ "Number of words in the periodic Tx FIFO 4-768"); ++module_param_named(host_rx_fifo_size, dwc_otg_module_params.host_rx_fifo_size, ++ int, 0444); ++MODULE_PARM_DESC(host_rx_fifo_size, "Number of words in the Rx FIFO 16-32768"); ++module_param_named(host_nperio_tx_fifo_size, ++ dwc_otg_module_params.host_nperio_tx_fifo_size, int, 0444); ++MODULE_PARM_DESC(host_nperio_tx_fifo_size, ++ "Number of words in the non-periodic Tx FIFO 16-32768"); ++module_param_named(host_perio_tx_fifo_size, ++ dwc_otg_module_params.host_perio_tx_fifo_size, int, 0444); ++MODULE_PARM_DESC(host_perio_tx_fifo_size, ++ "Number of words in the host periodic Tx FIFO 16-32768"); ++module_param_named(max_transfer_size, dwc_otg_module_params.max_transfer_size, ++ int, 0444); ++/** @todo Set the max to 512K, modify checks */ ++MODULE_PARM_DESC(max_transfer_size, ++ "The maximum transfer size supported in bytes 2047-65535"); ++module_param_named(max_packet_count, dwc_otg_module_params.max_packet_count, ++ int, 0444); ++MODULE_PARM_DESC(max_packet_count, ++ "The maximum number of packets in a transfer 15-511"); ++module_param_named(host_channels, dwc_otg_module_params.host_channels, int, ++ 0444); ++MODULE_PARM_DESC(host_channels, ++ "The number of host channel registers to use 1-16"); ++module_param_named(dev_endpoints, dwc_otg_module_params.dev_endpoints, int, ++ 0444); ++MODULE_PARM_DESC(dev_endpoints, ++ "The number of endpoints in addition to EP0 available for device mode 1-15"); ++module_param_named(phy_type, dwc_otg_module_params.phy_type, int, 0444); ++MODULE_PARM_DESC(phy_type, "0=Reserved 1=UTMI+ 2=ULPI"); ++module_param_named(phy_utmi_width, dwc_otg_module_params.phy_utmi_width, int, ++ 0444); ++MODULE_PARM_DESC(phy_utmi_width, "Specifies the UTMI+ Data Width 8 or 16 bits"); ++module_param_named(phy_ulpi_ddr, dwc_otg_module_params.phy_ulpi_ddr, int, 0444); ++MODULE_PARM_DESC(phy_ulpi_ddr, ++ "ULPI at double or single data rate 0=Single 1=Double"); ++module_param_named(phy_ulpi_ext_vbus, dwc_otg_module_params.phy_ulpi_ext_vbus, ++ int, 0444); ++MODULE_PARM_DESC(phy_ulpi_ext_vbus, ++ "ULPI PHY using internal or external vbus 0=Internal"); ++module_param_named(i2c_enable, dwc_otg_module_params.i2c_enable, int, 0444); ++MODULE_PARM_DESC(i2c_enable, "FS PHY Interface"); ++module_param_named(ulpi_fs_ls, dwc_otg_module_params.ulpi_fs_ls, int, 0444); ++MODULE_PARM_DESC(ulpi_fs_ls, "ULPI PHY FS/LS mode only"); ++module_param_named(ts_dline, dwc_otg_module_params.ts_dline, int, 0444); ++MODULE_PARM_DESC(ts_dline, "Term select Dline pulsing for all PHYs"); ++module_param_named(debug, g_dbg_lvl, int, 0444); ++MODULE_PARM_DESC(debug, ""); ++ ++module_param_named(en_multiple_tx_fifo, ++ dwc_otg_module_params.en_multiple_tx_fifo, int, 0444); ++MODULE_PARM_DESC(en_multiple_tx_fifo, ++ "Dedicated Non Periodic Tx FIFOs 0=disabled 1=enabled"); ++module_param_named(dev_tx_fifo_size_1, ++ dwc_otg_module_params.dev_tx_fifo_size[0], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_1, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_2, ++ dwc_otg_module_params.dev_tx_fifo_size[1], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_2, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_3, ++ dwc_otg_module_params.dev_tx_fifo_size[2], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_3, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_4, ++ dwc_otg_module_params.dev_tx_fifo_size[3], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_4, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_5, ++ dwc_otg_module_params.dev_tx_fifo_size[4], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_5, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_6, ++ dwc_otg_module_params.dev_tx_fifo_size[5], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_6, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_7, ++ dwc_otg_module_params.dev_tx_fifo_size[6], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_7, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_8, ++ dwc_otg_module_params.dev_tx_fifo_size[7], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_8, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_9, ++ dwc_otg_module_params.dev_tx_fifo_size[8], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_9, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_10, ++ dwc_otg_module_params.dev_tx_fifo_size[9], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_10, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_11, ++ dwc_otg_module_params.dev_tx_fifo_size[10], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_11, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_12, ++ dwc_otg_module_params.dev_tx_fifo_size[11], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_12, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_13, ++ dwc_otg_module_params.dev_tx_fifo_size[12], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_13, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_14, ++ dwc_otg_module_params.dev_tx_fifo_size[13], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_14, "Number of words in the Tx FIFO 4-768"); ++module_param_named(dev_tx_fifo_size_15, ++ dwc_otg_module_params.dev_tx_fifo_size[14], int, 0444); ++MODULE_PARM_DESC(dev_tx_fifo_size_15, "Number of words in the Tx FIFO 4-768"); ++ ++module_param_named(thr_ctl, dwc_otg_module_params.thr_ctl, int, 0444); ++MODULE_PARM_DESC(thr_ctl, ++ "Thresholding enable flag bit 0 - non ISO Tx thr., 1 - ISO Tx thr., 2 - Rx thr.- bit 0=disabled 1=enabled"); ++module_param_named(tx_thr_length, dwc_otg_module_params.tx_thr_length, int, ++ 0444); ++MODULE_PARM_DESC(tx_thr_length, "Tx Threshold length in 32 bit DWORDs"); ++module_param_named(rx_thr_length, dwc_otg_module_params.rx_thr_length, int, ++ 0444); ++MODULE_PARM_DESC(rx_thr_length, "Rx Threshold length in 32 bit DWORDs"); ++ ++module_param_named(pti_enable, dwc_otg_module_params.pti_enable, int, 0444); ++module_param_named(mpi_enable, dwc_otg_module_params.mpi_enable, int, 0444); ++module_param_named(lpm_enable, dwc_otg_module_params.lpm_enable, int, 0444); ++MODULE_PARM_DESC(lpm_enable, "LPM Enable 0=LPM Disabled 1=LPM Enabled"); ++module_param_named(ic_usb_cap, dwc_otg_module_params.ic_usb_cap, int, 0444); ++MODULE_PARM_DESC(ic_usb_cap, ++ "IC_USB Capability 0=IC_USB Disabled 1=IC_USB Enabled"); ++module_param_named(ahb_thr_ratio, dwc_otg_module_params.ahb_thr_ratio, int, ++ 0444); ++MODULE_PARM_DESC(ahb_thr_ratio, "AHB Threshold Ratio"); ++module_param_named(power_down, dwc_otg_module_params.power_down, int, 0444); ++MODULE_PARM_DESC(power_down, "Power Down Mode"); ++module_param_named(reload_ctl, dwc_otg_module_params.reload_ctl, int, 0444); ++MODULE_PARM_DESC(reload_ctl, "HFIR Reload Control"); ++module_param_named(dev_out_nak, dwc_otg_module_params.dev_out_nak, int, 0444); ++MODULE_PARM_DESC(dev_out_nak, "Enable Device OUT NAK"); ++module_param_named(cont_on_bna, dwc_otg_module_params.cont_on_bna, int, 0444); ++MODULE_PARM_DESC(cont_on_bna, "Enable Enable Continue on BNA"); ++module_param_named(ahb_single, dwc_otg_module_params.ahb_single, int, 0444); ++MODULE_PARM_DESC(ahb_single, "Enable AHB Single Support"); ++module_param_named(adp_enable, dwc_otg_module_params.adp_enable, int, 0444); ++MODULE_PARM_DESC(adp_enable, "ADP Enable 0=ADP Disabled 1=ADP Enabled"); ++module_param_named(otg_ver, dwc_otg_module_params.otg_ver, int, 0444); ++MODULE_PARM_DESC(otg_ver, "OTG revision supported 0=OTG 1.3 1=OTG 2.0"); ++module_param(microframe_schedule, bool, 0444); ++MODULE_PARM_DESC(microframe_schedule, "Enable the microframe scheduler"); ++ ++module_param(fiq_enable, bool, 0444); ++MODULE_PARM_DESC(fiq_enable, "Enable the FIQ"); ++module_param(nak_holdoff, ushort, 0644); ++MODULE_PARM_DESC(nak_holdoff, "Throttle duration for bulk split-transaction endpoints on a NAK. Default 8"); ++module_param(fiq_fsm_enable, bool, 0444); ++MODULE_PARM_DESC(fiq_fsm_enable, "Enable the FIQ to perform split transactions as defined by fiq_fsm_mask"); ++module_param(fiq_fsm_mask, ushort, 0444); ++MODULE_PARM_DESC(fiq_fsm_mask, "Bitmask of transactions to perform in the FIQ.\n" ++ "Bit 0 : Non-periodic split transactions\n" ++ "Bit 1 : Periodic split transactions\n" ++ "Bit 2 : High-speed multi-transfer isochronous\n" ++ "All other bits should be set 0."); ++module_param(int_ep_interval_min, ushort, 0644); ++MODULE_PARM_DESC(int_ep_interval_min, "Clamp high-speed Interrupt endpoints to a minimum polling interval.\n" ++ "0..1 = Use endpoint default\n" ++ "2..n = Minimum interval n microframes. Use powers of 2.\n"); ++ ++module_param(cil_force_host, bool, 0644); ++MODULE_PARM_DESC(cil_force_host, "On a connector-ID status change, " ++ "force Host Mode regardless of OTG state."); ++ ++/** @page "Module Parameters" ++ * ++ * The following parameters may be specified when starting the module. ++ * These parameters define how the DWC_otg controller should be ++ * configured. Parameter values are passed to the CIL initialization ++ * function dwc_otg_cil_init ++ * ++ * Example: modprobe dwc_otg speed=1 otg_cap=1 ++ * ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++ ++*/ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_driver.h +@@ -0,0 +1,86 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_driver.h $ ++ * $Revision: #19 $ ++ * $Date: 2010/11/15 $ ++ * $Change: 1627671 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++#ifndef __DWC_OTG_DRIVER_H__ ++#define __DWC_OTG_DRIVER_H__ ++ ++/** @file ++ * This file contains the interface to the Linux driver. ++ */ ++#include "dwc_otg_os_dep.h" ++#include "dwc_otg_core_if.h" ++ ++/* Type declarations */ ++struct dwc_otg_pcd; ++struct dwc_otg_hcd; ++ ++/** ++ * This structure is a wrapper that encapsulates the driver components used to ++ * manage a single DWC_otg controller. ++ */ ++typedef struct dwc_otg_device { ++ /** Structure containing OS-dependent stuff. KEEP THIS STRUCT AT THE ++ * VERY BEGINNING OF THE DEVICE STRUCT. OSes such as FreeBSD and NetBSD ++ * require this. */ ++ struct os_dependent os_dep; ++ ++ /** Pointer to the core interface structure. */ ++ dwc_otg_core_if_t *core_if; ++ ++ /** Pointer to the PCD structure. */ ++ struct dwc_otg_pcd *pcd; ++ ++ /** Pointer to the HCD structure. */ ++ struct dwc_otg_hcd *hcd; ++ ++ /** Flag to indicate whether the common IRQ handler is installed. */ ++ uint8_t common_irq_installed; ++ ++} dwc_otg_device_t; ++ ++/*We must clear S3C24XX_EINTPEND external interrupt register ++ * because after clearing in this register trigerred IRQ from ++ * H/W core in kernel interrupt can be occured again before OTG ++ * handlers clear all IRQ sources of Core registers because of ++ * timing latencies and Low Level IRQ Type. ++ */ ++#ifdef CONFIG_MACH_IPMATE ++#define S3C2410X_CLEAR_EINTPEND() \ ++do { \ ++ __raw_writel(1UL << 11,S3C24XX_EINTPEND); \ ++} while (0) ++#else ++#define S3C2410X_CLEAR_EINTPEND() do { } while (0) ++#endif ++ ++#endif +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.c +@@ -0,0 +1,1431 @@ ++/* ++ * dwc_otg_fiq_fsm.c - The finite state machine FIQ ++ * ++ * Copyright (c) 2013 Raspberry Pi Foundation ++ * ++ * Author: Jonathan Bell ++ * All rights reserved. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions are met: ++ * * Redistributions of source code must retain the above copyright ++ * notice, this list of conditions and the following disclaimer. ++ * * Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in the ++ * documentation and/or other materials provided with the distribution. ++ * * Neither the name of Raspberry Pi nor the ++ * names of its contributors may be used to endorse or promote products ++ * derived from this software without specific prior written permission. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ++ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED ++ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE ++ * DISCLAIMED. IN NO EVENT SHALL BE LIABLE FOR ANY ++ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; ++ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ++ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ * ++ * This FIQ implements functionality that performs split transactions on ++ * the dwc_otg hardware without any outside intervention. A split transaction ++ * is "queued" by nominating a specific host channel to perform the entirety ++ * of a split transaction. This FIQ will then perform the microframe-precise ++ * scheduling required in each phase of the transaction until completion. ++ * ++ * The FIQ functionality is glued into the Synopsys driver via the entry point ++ * in the FSM enqueue function, and at the exit point in handling a HC interrupt ++ * for a FSM-enabled channel. ++ * ++ * NB: Large parts of this implementation have architecture-specific code. ++ * For porting this functionality to other ARM machines, the minimum is required: ++ * - An interrupt controller allowing the top-level dwc USB interrupt to be routed ++ * to the FIQ ++ * - A method of forcing a software generated interrupt from FIQ mode that then ++ * triggers an IRQ entry (with the dwc USB handler called by this IRQ number) ++ * - Guaranteed interrupt routing such that both the FIQ and SGI occur on the same ++ * processor core - there is no locking between the FIQ and IRQ (aside from ++ * local_fiq_disable) ++ * ++ */ ++ ++#include "dwc_otg_fiq_fsm.h" ++ ++ ++char buffer[1000*16]; ++int wptr; ++void notrace _fiq_print(enum fiq_debug_level dbg_lvl, volatile struct fiq_state *state, char *fmt, ...) ++{ ++ enum fiq_debug_level dbg_lvl_req = FIQDBG_ERR; ++ va_list args; ++ char text[17]; ++ hfnum_data_t hfnum = { .d32 = FIQ_READ(state->dwc_regs_base + 0x408) }; ++ ++ if((dbg_lvl & dbg_lvl_req) || dbg_lvl == FIQDBG_ERR) ++ { ++ snprintf(text, 9, " %4d:%1u ", hfnum.b.frnum/8, hfnum.b.frnum & 7); ++ va_start(args, fmt); ++ vsnprintf(text+8, 9, fmt, args); ++ va_end(args); ++ ++ memcpy(buffer + wptr, text, 16); ++ wptr = (wptr + 16) % sizeof(buffer); ++ } ++} ++ ++ ++#ifdef CONFIG_ARM64 ++ ++inline void fiq_fsm_spin_lock(fiq_lock_t *lock) ++{ ++ spin_lock((spinlock_t *)lock); ++} ++ ++inline void fiq_fsm_spin_unlock(fiq_lock_t *lock) ++{ ++ spin_unlock((spinlock_t *)lock); ++} ++ ++#else ++ ++/** ++ * fiq_fsm_spin_lock() - ARMv6+ bare bones spinlock ++ * Must be called with local interrupts and FIQ disabled. ++ */ ++#if defined(CONFIG_ARCH_BCM2835) && defined(CONFIG_SMP) ++inline void fiq_fsm_spin_lock(fiq_lock_t *lock) ++{ ++ unsigned long tmp; ++ uint32_t newval; ++ fiq_lock_t lockval; ++ /* Nested locking, yay. If we are on the same CPU as the fiq, then the disable ++ * will be sufficient. If we are on a different CPU, then the lock protects us. */ ++ prefetchw(&lock->slock); ++ asm volatile ( ++ "1: ldrex %0, [%3]\n" ++ " add %1, %0, %4\n" ++ " strex %2, %1, [%3]\n" ++ " teq %2, #0\n" ++ " bne 1b" ++ : "=&r" (lockval), "=&r" (newval), "=&r" (tmp) ++ : "r" (&lock->slock), "I" (1 << 16) ++ : "cc"); ++ ++ while (lockval.tickets.next != lockval.tickets.owner) { ++ wfe(); ++ lockval.tickets.owner = READ_ONCE(lock->tickets.owner); ++ } ++ smp_mb(); ++} ++#else ++inline void fiq_fsm_spin_lock(fiq_lock_t *lock) { } ++#endif ++ ++/** ++ * fiq_fsm_spin_unlock() - ARMv6+ bare bones spinunlock ++ */ ++#if defined(CONFIG_ARCH_BCM2835) && defined(CONFIG_SMP) ++inline void fiq_fsm_spin_unlock(fiq_lock_t *lock) ++{ ++ smp_mb(); ++ lock->tickets.owner++; ++ dsb_sev(); ++} ++#else ++inline void fiq_fsm_spin_unlock(fiq_lock_t *lock) { } ++#endif ++ ++#endif ++ ++/** ++ * fiq_fsm_restart_channel() - Poke channel enable bit for a split transaction ++ * @channel: channel to re-enable ++ */ ++static void fiq_fsm_restart_channel(struct fiq_state *st, int n, int force) ++{ ++ hcchar_data_t hcchar = { .d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR) }; ++ ++ hcchar.b.chen = 0; ++ if (st->channel[n].hcchar_copy.b.eptype & 0x1) { ++ hfnum_data_t hfnum = { .d32 = FIQ_READ(st->dwc_regs_base + HFNUM) }; ++ /* Hardware bug workaround: update the ssplit index */ ++ if (st->channel[n].hcsplt_copy.b.spltena) ++ st->channel[n].expected_uframe = (hfnum.b.frnum + 1) & 0x3FFF; ++ ++ hcchar.b.oddfrm = (hfnum.b.frnum & 0x1) ? 0 : 1; ++ } ++ ++ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR, hcchar.d32); ++ hcchar.d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR); ++ hcchar.b.chen = 1; ++ ++ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR, hcchar.d32); ++ fiq_print(FIQDBG_INT, st, "HCGO %01d %01d", n, force); ++} ++ ++/** ++ * fiq_fsm_setup_csplit() - Prepare a host channel for a CSplit transaction stage ++ * @st: Pointer to the channel's state ++ * @n : channel number ++ * ++ * Change host channel registers to perform a complete-split transaction. Being mindful of the ++ * endpoint direction, set control regs up correctly. ++ */ ++static void notrace fiq_fsm_setup_csplit(struct fiq_state *st, int n) ++{ ++ hcsplt_data_t hcsplt = { .d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCSPLT) }; ++ hctsiz_data_t hctsiz = { .d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ) }; ++ ++ hcsplt.b.compsplt = 1; ++ if (st->channel[n].hcchar_copy.b.epdir == 1) { ++ // If IN, the CSPLIT result contains the data or a hub handshake. hctsiz = maxpacket. ++ hctsiz.b.xfersize = st->channel[n].hctsiz_copy.b.xfersize; ++ } else { ++ // If OUT, the CSPLIT result contains handshake only. ++ hctsiz.b.xfersize = 0; ++ } ++ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCSPLT, hcsplt.d32); ++ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ, hctsiz.d32); ++ mb(); ++} ++ ++/** ++ * fiq_fsm_restart_np_pending() - Restart a single non-periodic contended transfer ++ * @st: Pointer to the channel's state ++ * @num_channels: Total number of host channels ++ * @orig_channel: Channel index of completed transfer ++ * ++ * In the case where an IN and OUT transfer are simultaneously scheduled to the ++ * same device/EP, inadequate hub implementations will misbehave. Once the first ++ * transfer is complete, a pending non-periodic split can then be issued. ++ */ ++static void notrace fiq_fsm_restart_np_pending(struct fiq_state *st, int num_channels, int orig_channel) ++{ ++ int i; ++ int dev_addr = st->channel[orig_channel].hcchar_copy.b.devaddr; ++ int ep_num = st->channel[orig_channel].hcchar_copy.b.epnum; ++ for (i = 0; i < num_channels; i++) { ++ if (st->channel[i].fsm == FIQ_NP_SSPLIT_PENDING && ++ st->channel[i].hcchar_copy.b.devaddr == dev_addr && ++ st->channel[i].hcchar_copy.b.epnum == ep_num) { ++ st->channel[i].fsm = FIQ_NP_SSPLIT_STARTED; ++ fiq_fsm_restart_channel(st, i, 0); ++ break; ++ } ++ } ++} ++ ++static inline int notrace fiq_get_xfer_len(struct fiq_state *st, int n) ++{ ++ /* The xfersize register is a bit wonky. For IN transfers, it decrements by the packet size. */ ++ hctsiz_data_t hctsiz = { .d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ) }; ++ ++ if (st->channel[n].hcchar_copy.b.epdir == 0) { ++ return st->channel[n].hctsiz_copy.b.xfersize; ++ } else { ++ return st->channel[n].hctsiz_copy.b.xfersize - hctsiz.b.xfersize; ++ } ++ ++} ++ ++ ++/** ++ * fiq_increment_dma_buf() - update DMA address for bounce buffers after a CSPLIT ++ * ++ * Of use only for IN periodic transfers. ++ */ ++static int notrace fiq_increment_dma_buf(struct fiq_state *st, int num_channels, int n) ++{ ++ hcdma_data_t hcdma; ++ int i = st->channel[n].dma_info.index; ++ int len; ++ struct fiq_dma_blob *blob = (struct fiq_dma_blob *) st->dma_base; ++ ++ len = fiq_get_xfer_len(st, n); ++ fiq_print(FIQDBG_INT, st, "LEN: %03d", len); ++ st->channel[n].dma_info.slot_len[i] = len; ++ i++; ++ if (i > 6) ++ BUG(); ++ ++ hcdma.d32 = (dma_addr_t) &blob->channel[n].index[i].buf[0]; ++ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HC_DMA, hcdma.d32); ++ st->channel[n].dma_info.index = i; ++ return 0; ++} ++ ++/** ++ * fiq_reload_hctsiz() - for IN transactions, reset HCTSIZ ++ */ ++static void notrace fiq_fsm_reload_hctsiz(struct fiq_state *st, int n) ++{ ++ hctsiz_data_t hctsiz = { .d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ) }; ++ hctsiz.b.xfersize = st->channel[n].hctsiz_copy.b.xfersize; ++ hctsiz.b.pktcnt = 1; ++ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ, hctsiz.d32); ++} ++ ++/** ++ * fiq_fsm_reload_hcdma() - for OUT transactions, rewind DMA pointer ++ */ ++static void notrace fiq_fsm_reload_hcdma(struct fiq_state *st, int n) ++{ ++ hcdma_data_t hcdma = st->channel[n].hcdma_copy; ++ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HC_DMA, hcdma.d32); ++} ++ ++/** ++ * fiq_iso_out_advance() - update DMA address and split position bits ++ * for isochronous OUT transactions. ++ * ++ * Returns 1 if this is the last packet queued, 0 otherwise. Split-ALL and ++ * Split-BEGIN states are not handled - this is done when the transaction was queued. ++ * ++ * This function must only be called from the FIQ_ISO_OUT_ACTIVE state. ++ */ ++static int notrace fiq_iso_out_advance(struct fiq_state *st, int num_channels, int n) ++{ ++ hcsplt_data_t hcsplt; ++ hctsiz_data_t hctsiz; ++ hcdma_data_t hcdma; ++ struct fiq_dma_blob *blob = (struct fiq_dma_blob *) st->dma_base; ++ int last = 0; ++ int i = st->channel[n].dma_info.index; ++ ++ fiq_print(FIQDBG_INT, st, "ADV %01d %01d ", n, i); ++ i++; ++ if (i == 4) ++ last = 1; ++ if (st->channel[n].dma_info.slot_len[i+1] == 255) ++ last = 1; ++ ++ /* New DMA address - address of bounce buffer referred to in index */ ++ hcdma.d32 = (dma_addr_t) blob->channel[n].index[i].buf; ++ //hcdma.d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HC_DMA); ++ //hcdma.d32 += st->channel[n].dma_info.slot_len[i]; ++ fiq_print(FIQDBG_INT, st, "LAST: %01d ", last); ++ fiq_print(FIQDBG_INT, st, "LEN: %03d", st->channel[n].dma_info.slot_len[i]); ++ hcsplt.d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCSPLT); ++ hctsiz.d32 = FIQ_READ(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ); ++ hcsplt.b.xactpos = (last) ? ISOC_XACTPOS_END : ISOC_XACTPOS_MID; ++ /* Set up new packet length */ ++ hctsiz.b.pktcnt = 1; ++ hctsiz.b.xfersize = st->channel[n].dma_info.slot_len[i]; ++ fiq_print(FIQDBG_INT, st, "%08x", hctsiz.d32); ++ ++ st->channel[n].dma_info.index++; ++ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCSPLT, hcsplt.d32); ++ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ, hctsiz.d32); ++ FIQ_WRITE(st->dwc_regs_base + HC_START + (HC_OFFSET * n) + HC_DMA, hcdma.d32); ++ return last; ++} ++ ++/** ++ * fiq_fsm_tt_next_isoc() - queue next pending isochronous out start-split on a TT ++ * ++ * Despite the limitations of the DWC core, we can force a microframe pipeline of ++ * isochronous OUT start-split transactions while waiting for a corresponding other-type ++ * of endpoint to finish its CSPLITs. TTs have big periodic buffers therefore it ++ * is very unlikely that filling the start-split FIFO will cause data loss. ++ * This allows much better interleaving of transactions in an order-independent way- ++ * there is no requirement to prioritise isochronous, just a state-space search has ++ * to be performed on each periodic start-split complete interrupt. ++ */ ++static int notrace fiq_fsm_tt_next_isoc(struct fiq_state *st, int num_channels, int n) ++{ ++ int hub_addr = st->channel[n].hub_addr; ++ int port_addr = st->channel[n].port_addr; ++ int i, poked = 0; ++ for (i = 0; i < num_channels; i++) { ++ if (i == n || st->channel[i].fsm == FIQ_PASSTHROUGH) ++ continue; ++ if (st->channel[i].hub_addr == hub_addr && ++ st->channel[i].port_addr == port_addr) { ++ switch (st->channel[i].fsm) { ++ case FIQ_PER_ISO_OUT_PENDING: ++ if (st->channel[i].nrpackets == 1) { ++ st->channel[i].fsm = FIQ_PER_ISO_OUT_LAST; ++ } else { ++ st->channel[i].fsm = FIQ_PER_ISO_OUT_ACTIVE; ++ } ++ fiq_fsm_restart_channel(st, i, 0); ++ poked = 1; ++ break; ++ ++ default: ++ break; ++ } ++ } ++ if (poked) ++ break; ++ } ++ return poked; ++} ++ ++/** ++ * fiq_fsm_tt_in_use() - search for host channels using this TT ++ * @n: Channel to use as reference ++ * ++ */ ++int notrace noinline fiq_fsm_tt_in_use(struct fiq_state *st, int num_channels, int n) ++{ ++ int hub_addr = st->channel[n].hub_addr; ++ int port_addr = st->channel[n].port_addr; ++ int i, in_use = 0; ++ for (i = 0; i < num_channels; i++) { ++ if (i == n || st->channel[i].fsm == FIQ_PASSTHROUGH) ++ continue; ++ switch (st->channel[i].fsm) { ++ /* TT is reserved for channels that are in the middle of a periodic ++ * split transaction. ++ */ ++ case FIQ_PER_SSPLIT_STARTED: ++ case FIQ_PER_CSPLIT_WAIT: ++ case FIQ_PER_CSPLIT_NYET1: ++ //case FIQ_PER_CSPLIT_POLL: ++ case FIQ_PER_ISO_OUT_ACTIVE: ++ case FIQ_PER_ISO_OUT_LAST: ++ if (st->channel[i].hub_addr == hub_addr && ++ st->channel[i].port_addr == port_addr) { ++ in_use = 1; ++ } ++ break; ++ default: ++ break; ++ } ++ if (in_use) ++ break; ++ } ++ return in_use; ++} ++ ++/** ++ * fiq_fsm_more_csplits() - determine whether additional CSPLITs need ++ * to be issued for this IN transaction. ++ * ++ * We cannot tell the inbound PID of a data packet due to hardware limitations. ++ * we need to make an educated guess as to whether we need to queue another CSPLIT ++ * or not. A no-brainer is when we have received enough data to fill the endpoint ++ * size, but for endpoints that give variable-length data then we have to resort ++ * to heuristics. ++ * ++ * We also return whether this is the last CSPLIT to be queued, again based on ++ * heuristics. This is to allow a 1-uframe overlap of periodic split transactions. ++ * Note: requires at least 1 CSPLIT to have been performed prior to being called. ++ */ ++ ++/* ++ * We need some way of guaranteeing if a returned periodic packet of size X ++ * has a DATA0 PID. ++ * The heuristic value of 144 bytes assumes that the received data has maximal ++ * bit-stuffing and the clock frequency of the transmitting device is at the lowest ++ * permissible limit. If the transfer length results in a final packet size ++ * 144 < p <= 188, then an erroneous CSPLIT will be issued. ++ * Also used to ensure that an endpoint will nominally only return a single ++ * complete-split worth of data. ++ */ ++#define DATA0_PID_HEURISTIC 144 ++ ++static int notrace noinline fiq_fsm_more_csplits(struct fiq_state *state, int n, int *probably_last) ++{ ++ ++ int i; ++ int total_len = 0; ++ int more_needed = 1; ++ struct fiq_channel_state *st = &state->channel[n]; ++ ++ for (i = 0; i < st->dma_info.index; i++) { ++ total_len += st->dma_info.slot_len[i]; ++ } ++ ++ *probably_last = 0; ++ ++ if (st->hcchar_copy.b.eptype == 0x3) { ++ /* ++ * An interrupt endpoint will take max 2 CSPLITs. if we are receiving data ++ * then this is definitely the last CSPLIT. ++ */ ++ *probably_last = 1; ++ } else { ++ /* Isoc IN. This is a bit risky if we are the first transaction: ++ * we may have been held off slightly. */ ++ if (i > 1 && st->dma_info.slot_len[st->dma_info.index-1] <= DATA0_PID_HEURISTIC) { ++ more_needed = 0; ++ } ++ /* If in the next uframe we will receive enough data to fill the endpoint, ++ * then only issue 1 more csplit. ++ */ ++ if (st->hctsiz_copy.b.xfersize - total_len <= DATA0_PID_HEURISTIC) ++ *probably_last = 1; ++ } ++ ++ if (total_len >= st->hctsiz_copy.b.xfersize || ++ i == 6 || total_len == 0) ++ /* Note: due to bit stuffing it is possible to have > 6 CSPLITs for ++ * a single endpoint. Accepting more would completely break our scheduling mechanism though ++ * - in these extreme cases we will pass through a truncated packet. ++ */ ++ more_needed = 0; ++ ++ return more_needed; ++} ++ ++/** ++ * fiq_fsm_too_late() - Test transaction for lateness ++ * ++ * If a SSPLIT for a large IN transaction is issued too late in a frame, ++ * the hub will disable the port to the device and respond with ERR handshakes. ++ * The hub status endpoint will not reflect this change. ++ * Returns 1 if we will issue a SSPLIT that will result in a device babble. ++ */ ++int notrace fiq_fsm_too_late(struct fiq_state *st, int n) ++{ ++ int uframe; ++ hfnum_data_t hfnum = { .d32 = FIQ_READ(st->dwc_regs_base + HFNUM) }; ++ uframe = hfnum.b.frnum & 0x7; ++ if ((uframe < 6) && (st->channel[n].nrpackets + 1 + uframe > 7)) { ++ return 1; ++ } else { ++ return 0; ++ } ++} ++ ++ ++/** ++ * fiq_fsm_start_next_periodic() - A half-arsed attempt at a microframe pipeline ++ * ++ * Search pending transactions in the start-split pending state and queue them. ++ * Don't queue packets in uframe .5 (comes out in .6) (USB2.0 11.18.4). ++ * Note: we specifically don't do isochronous OUT transactions first because better ++ * use of the TT's start-split fifo can be achieved by pipelining an IN before an OUT. ++ */ ++static void notrace noinline fiq_fsm_start_next_periodic(struct fiq_state *st, int num_channels) ++{ ++ int n; ++ hfnum_data_t hfnum = { .d32 = FIQ_READ(st->dwc_regs_base + HFNUM) }; ++ if ((hfnum.b.frnum & 0x7) == 5) ++ return; ++ for (n = 0; n < num_channels; n++) { ++ if (st->channel[n].fsm == FIQ_PER_SSPLIT_QUEUED) { ++ /* Check to see if any other transactions are using this TT */ ++ if(!fiq_fsm_tt_in_use(st, num_channels, n)) { ++ if (!fiq_fsm_too_late(st, n)) { ++ st->channel[n].fsm = FIQ_PER_SSPLIT_STARTED; ++ fiq_print(FIQDBG_INT, st, "NEXTPER "); ++ fiq_fsm_restart_channel(st, n, 0); ++ } else { ++ st->channel[n].fsm = FIQ_PER_SPLIT_TIMEOUT; ++ } ++ break; ++ } ++ } ++ } ++ for (n = 0; n < num_channels; n++) { ++ if (st->channel[n].fsm == FIQ_PER_ISO_OUT_PENDING) { ++ if (!fiq_fsm_tt_in_use(st, num_channels, n)) { ++ fiq_print(FIQDBG_INT, st, "NEXTISO "); ++ if (st->channel[n].nrpackets == 1) ++ st->channel[n].fsm = FIQ_PER_ISO_OUT_LAST; ++ else ++ st->channel[n].fsm = FIQ_PER_ISO_OUT_ACTIVE; ++ fiq_fsm_restart_channel(st, n, 0); ++ break; ++ } ++ } ++ } ++} ++ ++/** ++ * fiq_fsm_update_hs_isoc() - update isochronous frame and transfer data ++ * @state: Pointer to fiq_state ++ * @n: Channel transaction is active on ++ * @hcint: Copy of host channel interrupt register ++ * ++ * Returns 0 if there are no more transactions for this HC to do, 1 ++ * otherwise. ++ */ ++static int notrace noinline fiq_fsm_update_hs_isoc(struct fiq_state *state, int n, hcint_data_t hcint) ++{ ++ struct fiq_channel_state *st = &state->channel[n]; ++ int xfer_len = 0, nrpackets = 0; ++ hcdma_data_t hcdma; ++ fiq_print(FIQDBG_INT, state, "HSISO %02d", n); ++ ++ xfer_len = fiq_get_xfer_len(state, n); ++ st->hs_isoc_info.iso_desc[st->hs_isoc_info.index].actual_length = xfer_len; ++ ++ st->hs_isoc_info.iso_desc[st->hs_isoc_info.index].status = hcint.d32; ++ ++ st->hs_isoc_info.index++; ++ if (st->hs_isoc_info.index == st->hs_isoc_info.nrframes) { ++ return 0; ++ } ++ ++ /* grab the next DMA address offset from the array */ ++ hcdma.d32 = st->hcdma_copy.d32 + st->hs_isoc_info.iso_desc[st->hs_isoc_info.index].offset; ++ FIQ_WRITE(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HC_DMA, hcdma.d32); ++ ++ /* We need to set multi_count. This is a bit tricky - has to be set per-transaction as ++ * the core needs to be told to send the correct number. Caution: for IN transfers, ++ * this is always set to the maximum size of the endpoint. */ ++ xfer_len = st->hs_isoc_info.iso_desc[st->hs_isoc_info.index].length; ++ /* Integer divide in a FIQ: fun. FIXME: make this not suck */ ++ nrpackets = (xfer_len + st->hcchar_copy.b.mps - 1) / st->hcchar_copy.b.mps; ++ if (nrpackets == 0) ++ nrpackets = 1; ++ st->hcchar_copy.b.multicnt = nrpackets; ++ st->hctsiz_copy.b.pktcnt = nrpackets; ++ ++ /* Initial PID also needs to be set */ ++ if (st->hcchar_copy.b.epdir == 0) { ++ st->hctsiz_copy.b.xfersize = xfer_len; ++ switch (st->hcchar_copy.b.multicnt) { ++ case 1: ++ st->hctsiz_copy.b.pid = DWC_PID_DATA0; ++ break; ++ case 2: ++ case 3: ++ st->hctsiz_copy.b.pid = DWC_PID_MDATA; ++ break; ++ } ++ ++ } else { ++ st->hctsiz_copy.b.xfersize = nrpackets * st->hcchar_copy.b.mps; ++ switch (st->hcchar_copy.b.multicnt) { ++ case 1: ++ st->hctsiz_copy.b.pid = DWC_PID_DATA0; ++ break; ++ case 2: ++ st->hctsiz_copy.b.pid = DWC_PID_DATA1; ++ break; ++ case 3: ++ st->hctsiz_copy.b.pid = DWC_PID_DATA2; ++ break; ++ } ++ } ++ FIQ_WRITE(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCTSIZ, st->hctsiz_copy.d32); ++ FIQ_WRITE(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR, st->hcchar_copy.d32); ++ /* Channel is enabled on hcint handler exit */ ++ fiq_print(FIQDBG_INT, state, "HSISOOUT"); ++ return 1; ++} ++ ++ ++/** ++ * fiq_fsm_do_sof() - FSM start-of-frame interrupt handler ++ * @state: Pointer to the state struct passed from banked FIQ mode registers. ++ * @num_channels: set according to the DWC hardware configuration ++ * ++ * The SOF handler in FSM mode has two functions ++ * 1. Hold off SOF from causing schedule advancement in IRQ context if there's ++ * nothing to do ++ * 2. Advance certain FSM states that require either a microframe delay, or a microframe ++ * of holdoff. ++ * ++ * The second part is architecture-specific to mach-bcm2835 - ++ * a sane interrupt controller would have a mask register for ARM interrupt sources ++ * to be promoted to the nFIQ line, but it doesn't. Instead a single interrupt ++ * number (USB) can be enabled. This means that certain parts of the USB specification ++ * that require "wait a little while, then issue another packet" cannot be fulfilled with ++ * the timing granularity required to achieve optimal throughout. The workaround is to use ++ * the SOF "timer" (125uS) to perform this task. ++ */ ++static int notrace noinline fiq_fsm_do_sof(struct fiq_state *state, int num_channels) ++{ ++ hfnum_data_t hfnum = { .d32 = FIQ_READ(state->dwc_regs_base + HFNUM) }; ++ int n; ++ int kick_irq = 0; ++ ++ if ((hfnum.b.frnum & 0x7) == 1) { ++ /* We cannot issue csplits for transactions in the last frame past (n+1).1 ++ * Check to see if there are any transactions that are stale. ++ * Boot them out. ++ */ ++ for (n = 0; n < num_channels; n++) { ++ switch (state->channel[n].fsm) { ++ case FIQ_PER_CSPLIT_WAIT: ++ case FIQ_PER_CSPLIT_NYET1: ++ case FIQ_PER_CSPLIT_POLL: ++ case FIQ_PER_CSPLIT_LAST: ++ /* Check if we are no longer in the same full-speed frame. */ ++ if (((state->channel[n].expected_uframe & 0x3FFF) & ~0x7) < ++ (hfnum.b.frnum & ~0x7)) ++ state->channel[n].fsm = FIQ_PER_SPLIT_TIMEOUT; ++ break; ++ default: ++ break; ++ } ++ } ++ } ++ ++ for (n = 0; n < num_channels; n++) { ++ switch (state->channel[n].fsm) { ++ ++ case FIQ_NP_SSPLIT_RETRY: ++ case FIQ_NP_IN_CSPLIT_RETRY: ++ case FIQ_NP_OUT_CSPLIT_RETRY: ++ fiq_fsm_restart_channel(state, n, 0); ++ break; ++ ++ case FIQ_HS_ISOC_SLEEPING: ++ /* Is it time to wake this channel yet? */ ++ if (--state->channel[n].uframe_sleeps == 0) { ++ state->channel[n].fsm = FIQ_HS_ISOC_TURBO; ++ fiq_fsm_restart_channel(state, n, 0); ++ } ++ break; ++ ++ case FIQ_PER_SSPLIT_QUEUED: ++ if ((hfnum.b.frnum & 0x7) == 5) ++ break; ++ if(!fiq_fsm_tt_in_use(state, num_channels, n)) { ++ if (!fiq_fsm_too_late(state, n)) { ++ fiq_print(FIQDBG_INT, state, "SOF GO %01d", n); ++ fiq_fsm_restart_channel(state, n, 0); ++ state->channel[n].fsm = FIQ_PER_SSPLIT_STARTED; ++ } else { ++ /* Transaction cannot be started without risking a device babble error */ ++ state->channel[n].fsm = FIQ_PER_SPLIT_TIMEOUT; ++ state->haintmsk_saved.b2.chint &= ~(1 << n); ++ FIQ_WRITE(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCINTMSK, 0); ++ kick_irq |= 1; ++ } ++ } ++ break; ++ ++ case FIQ_PER_ISO_OUT_PENDING: ++ /* Ordinarily, this should be poked after the SSPLIT ++ * complete interrupt for a competing transfer on the same ++ * TT. Doesn't happen for aborted transactions though. ++ */ ++ if ((hfnum.b.frnum & 0x7) >= 5) ++ break; ++ if (!fiq_fsm_tt_in_use(state, num_channels, n)) { ++ /* Hardware bug. SOF can sometimes occur after the channel halt interrupt ++ * that caused this. ++ */ ++ fiq_fsm_restart_channel(state, n, 0); ++ fiq_print(FIQDBG_INT, state, "SOF ISOC"); ++ if (state->channel[n].nrpackets == 1) { ++ state->channel[n].fsm = FIQ_PER_ISO_OUT_LAST; ++ } else { ++ state->channel[n].fsm = FIQ_PER_ISO_OUT_ACTIVE; ++ } ++ } ++ break; ++ ++ case FIQ_PER_CSPLIT_WAIT: ++ /* we are guaranteed to be in this state if and only if the SSPLIT interrupt ++ * occurred when the bus transaction occurred. The SOF interrupt reversal bug ++ * will utterly bugger this up though. ++ */ ++ if (hfnum.b.frnum != state->channel[n].expected_uframe) { ++ fiq_print(FIQDBG_INT, state, "SOFCS %d ", n); ++ state->channel[n].fsm = FIQ_PER_CSPLIT_POLL; ++ fiq_fsm_restart_channel(state, n, 0); ++ fiq_fsm_start_next_periodic(state, num_channels); ++ ++ } ++ break; ++ ++ case FIQ_PER_SPLIT_TIMEOUT: ++ case FIQ_DEQUEUE_ISSUED: ++ /* Ugly: we have to force a HCD interrupt. ++ * Poke the mask for the channel in question. ++ * We will take a fake SOF because of this, but ++ * that's OK. ++ */ ++ state->haintmsk_saved.b2.chint &= ~(1 << n); ++ FIQ_WRITE(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCINTMSK, 0); ++ kick_irq |= 1; ++ break; ++ ++ default: ++ break; ++ } ++ } ++ ++ if (state->kick_np_queues || ++ dwc_frame_num_le(state->next_sched_frame, hfnum.b.frnum)) ++ kick_irq |= 1; ++ ++ return !kick_irq; ++} ++ ++ ++/** ++ * fiq_fsm_do_hcintr() - FSM host channel interrupt handler ++ * @state: Pointer to the FIQ state struct ++ * @num_channels: Number of channels as per hardware config ++ * @n: channel for which HAINT(i) was raised ++ * ++ * An important property is that only the CHHLT interrupt is unmasked. Unfortunately, AHBerr is as well. ++ */ ++static int notrace noinline fiq_fsm_do_hcintr(struct fiq_state *state, int num_channels, int n) ++{ ++ hcint_data_t hcint; ++ hcintmsk_data_t hcintmsk; ++ hcint_data_t hcint_probe; ++ hcchar_data_t hcchar; ++ int handled = 0; ++ int restart = 0; ++ int last_csplit = 0; ++ int start_next_periodic = 0; ++ struct fiq_channel_state *st = &state->channel[n]; ++ hfnum_data_t hfnum; ++ ++ hcint.d32 = FIQ_READ(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCINT); ++ hcintmsk.d32 = FIQ_READ(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCINTMSK); ++ hcint_probe.d32 = hcint.d32 & hcintmsk.d32; ++ ++ if (st->fsm != FIQ_PASSTHROUGH) { ++ fiq_print(FIQDBG_INT, state, "HC%01d ST%02d", n, st->fsm); ++ fiq_print(FIQDBG_INT, state, "%08x", hcint.d32); ++ } ++ ++ switch (st->fsm) { ++ ++ case FIQ_PASSTHROUGH: ++ case FIQ_DEQUEUE_ISSUED: ++ /* doesn't belong to us, kick it upstairs */ ++ break; ++ ++ case FIQ_PASSTHROUGH_ERRORSTATE: ++ /* We are here to emulate the error recovery mechanism of the dwc HCD. ++ * Several interrupts are unmasked if a previous transaction failed - it's ++ * death for the FIQ to attempt to handle them as the channel isn't halted. ++ * Emulate what the HCD does in this situation: mask and continue. ++ * The FSM has no other state setup so this has to be handled out-of-band. ++ */ ++ fiq_print(FIQDBG_ERR, state, "ERRST %02d", n); ++ if (hcint_probe.b.nak || hcint_probe.b.ack || hcint_probe.b.datatglerr) { ++ fiq_print(FIQDBG_ERR, state, "RESET %02d", n); ++ /* In some random cases we can get a NAK interrupt coincident with a Xacterr ++ * interrupt, after the device has disappeared. ++ */ ++ if (!hcint.b.xacterr) ++ st->nr_errors = 0; ++ hcintmsk.b.nak = 0; ++ hcintmsk.b.ack = 0; ++ hcintmsk.b.datatglerr = 0; ++ FIQ_WRITE(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCINTMSK, hcintmsk.d32); ++ return 1; ++ } ++ if (hcint_probe.b.chhltd) { ++ fiq_print(FIQDBG_ERR, state, "CHHLT %02d", n); ++ fiq_print(FIQDBG_ERR, state, "%08x", hcint.d32); ++ return 0; ++ } ++ break; ++ ++ /* Non-periodic state groups */ ++ case FIQ_NP_SSPLIT_STARTED: ++ case FIQ_NP_SSPLIT_RETRY: ++ /* Got a HCINT for a NP SSPLIT. Expected ACK / NAK / fail */ ++ if (hcint.b.ack) { ++ /* SSPLIT complete. For OUT, the data has been sent. For IN, the LS transaction ++ * will start shortly. SOF needs to kick the transaction to prevent a NYET flood. ++ */ ++ if(st->hcchar_copy.b.epdir == 1) ++ st->fsm = FIQ_NP_IN_CSPLIT_RETRY; ++ else ++ st->fsm = FIQ_NP_OUT_CSPLIT_RETRY; ++ st->nr_errors = 0; ++ handled = 1; ++ fiq_fsm_setup_csplit(state, n); ++ } else if (hcint.b.nak) { ++ // No buffer space in TT. Retry on a uframe boundary. ++ fiq_fsm_reload_hcdma(state, n); ++ st->fsm = FIQ_NP_SSPLIT_RETRY; ++ handled = 1; ++ } else if (hcint.b.xacterr) { ++ // The only other one we care about is xacterr. This implies HS bus error - retry. ++ st->nr_errors++; ++ if(st->hcchar_copy.b.epdir == 0) ++ fiq_fsm_reload_hcdma(state, n); ++ st->fsm = FIQ_NP_SSPLIT_RETRY; ++ if (st->nr_errors >= 3) { ++ st->fsm = FIQ_NP_SPLIT_HS_ABORTED; ++ } else { ++ handled = 1; ++ restart = 1; ++ } ++ } else { ++ st->fsm = FIQ_NP_SPLIT_LS_ABORTED; ++ handled = 0; ++ restart = 0; ++ } ++ break; ++ ++ case FIQ_NP_IN_CSPLIT_RETRY: ++ /* Received a CSPLIT done interrupt. ++ * Expected Data/NAK/STALL/NYET for IN. ++ */ ++ if (hcint.b.xfercomp) { ++ /* For IN, data is present. */ ++ st->fsm = FIQ_NP_SPLIT_DONE; ++ } else if (hcint.b.nak) { ++ /* no endpoint data. Punt it upstairs */ ++ st->fsm = FIQ_NP_SPLIT_DONE; ++ } else if (hcint.b.nyet) { ++ /* CSPLIT NYET - retry on a uframe boundary. */ ++ handled = 1; ++ st->nr_errors = 0; ++ } else if (hcint.b.datatglerr) { ++ /* data toggle errors do not set the xfercomp bit. */ ++ st->fsm = FIQ_NP_SPLIT_LS_ABORTED; ++ } else if (hcint.b.xacterr) { ++ /* HS error. Retry immediate */ ++ st->fsm = FIQ_NP_IN_CSPLIT_RETRY; ++ st->nr_errors++; ++ if (st->nr_errors >= 3) { ++ st->fsm = FIQ_NP_SPLIT_HS_ABORTED; ++ } else { ++ handled = 1; ++ restart = 1; ++ } ++ } else if (hcint.b.stall || hcint.b.bblerr) { ++ /* A STALL implies either a LS bus error or a genuine STALL. */ ++ st->fsm = FIQ_NP_SPLIT_LS_ABORTED; ++ } else { ++ /* Hardware bug. It's possible in some cases to ++ * get a channel halt with nothing else set when ++ * the response was a NYET. Treat as local 3-strikes retry. ++ */ ++ hcint_data_t hcint_test = hcint; ++ hcint_test.b.chhltd = 0; ++ if (!hcint_test.d32) { ++ st->nr_errors++; ++ if (st->nr_errors >= 3) { ++ st->fsm = FIQ_NP_SPLIT_HS_ABORTED; ++ } else { ++ handled = 1; ++ } ++ } else { ++ /* Bail out if something unexpected happened */ ++ st->fsm = FIQ_NP_SPLIT_HS_ABORTED; ++ } ++ } ++ if (st->fsm != FIQ_NP_IN_CSPLIT_RETRY) { ++ fiq_fsm_restart_np_pending(state, num_channels, n); ++ } ++ break; ++ ++ case FIQ_NP_OUT_CSPLIT_RETRY: ++ /* Received a CSPLIT done interrupt. ++ * Expected ACK/NAK/STALL/NYET/XFERCOMP for OUT.*/ ++ if (hcint.b.xfercomp) { ++ st->fsm = FIQ_NP_SPLIT_DONE; ++ } else if (hcint.b.nak) { ++ // The HCD will implement the holdoff on frame boundaries. ++ st->fsm = FIQ_NP_SPLIT_DONE; ++ } else if (hcint.b.nyet) { ++ // Hub still processing. ++ st->fsm = FIQ_NP_OUT_CSPLIT_RETRY; ++ handled = 1; ++ st->nr_errors = 0; ++ //restart = 1; ++ } else if (hcint.b.xacterr) { ++ /* HS error. retry immediate */ ++ st->fsm = FIQ_NP_OUT_CSPLIT_RETRY; ++ st->nr_errors++; ++ if (st->nr_errors >= 3) { ++ st->fsm = FIQ_NP_SPLIT_HS_ABORTED; ++ } else { ++ handled = 1; ++ restart = 1; ++ } ++ } else if (hcint.b.stall) { ++ /* LS bus error or genuine stall */ ++ st->fsm = FIQ_NP_SPLIT_LS_ABORTED; ++ } else { ++ /* ++ * Hardware bug. It's possible in some cases to get a ++ * channel halt with nothing else set when the response was a NYET. ++ * Treat as local 3-strikes retry. ++ */ ++ hcint_data_t hcint_test = hcint; ++ hcint_test.b.chhltd = 0; ++ if (!hcint_test.d32) { ++ st->nr_errors++; ++ if (st->nr_errors >= 3) { ++ st->fsm = FIQ_NP_SPLIT_HS_ABORTED; ++ } else { ++ handled = 1; ++ } ++ } else { ++ // Something unexpected happened. AHBerror or babble perhaps. Let the IRQ deal with it. ++ st->fsm = FIQ_NP_SPLIT_HS_ABORTED; ++ } ++ } ++ if (st->fsm != FIQ_NP_OUT_CSPLIT_RETRY) { ++ fiq_fsm_restart_np_pending(state, num_channels, n); ++ } ++ break; ++ ++ /* Periodic split states (except isoc out) */ ++ case FIQ_PER_SSPLIT_STARTED: ++ /* Expect an ACK or failure for SSPLIT */ ++ if (hcint.b.ack) { ++ /* ++ * SSPLIT transfer complete interrupt - the generation of this interrupt is fraught with bugs. ++ * For a packet queued in microframe n-3 to appear in n-2, if the channel is enabled near the EOF1 ++ * point for microframe n-3, the packet will not appear on the bus until microframe n. ++ * Additionally, the generation of the actual interrupt is dodgy. For a packet appearing on the bus ++ * in microframe n, sometimes the interrupt is generated immediately. Sometimes, it appears in n+1 ++ * coincident with SOF for n+1. ++ * SOF is also buggy. It can sometimes be raised AFTER the first bus transaction has taken place. ++ * These appear to be caused by timing/clock crossing bugs within the core itself. ++ * State machine workaround. ++ */ ++ hfnum.d32 = FIQ_READ(state->dwc_regs_base + HFNUM); ++ hcchar.d32 = FIQ_READ(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR); ++ fiq_fsm_setup_csplit(state, n); ++ /* Poke the oddfrm bit. If we are equivalent, we received the interrupt at the correct ++ * time. If not, then we're in the next SOF. ++ */ ++ if ((hfnum.b.frnum & 0x1) == hcchar.b.oddfrm) { ++ fiq_print(FIQDBG_INT, state, "CSWAIT %01d", n); ++ st->expected_uframe = hfnum.b.frnum; ++ st->fsm = FIQ_PER_CSPLIT_WAIT; ++ } else { ++ fiq_print(FIQDBG_INT, state, "CSPOL %01d", n); ++ /* For isochronous IN endpoints, ++ * we need to hold off if we are expecting a lot of data */ ++ if (st->hcchar_copy.b.mps < DATA0_PID_HEURISTIC) { ++ start_next_periodic = 1; ++ } ++ /* Danger will robinson: we are in a broken state. If our first interrupt after ++ * this is a NYET, it will be delayed by 1 uframe and result in an unrecoverable ++ * lag. Unmask the NYET interrupt. ++ */ ++ st->expected_uframe = (hfnum.b.frnum + 1) & 0x3FFF; ++ st->fsm = FIQ_PER_CSPLIT_BROKEN_NYET1; ++ restart = 1; ++ } ++ handled = 1; ++ } else if (hcint.b.xacterr) { ++ /* 3-strikes retry is enabled, we have hit our max nr_errors */ ++ st->fsm = FIQ_PER_SPLIT_HS_ABORTED; ++ start_next_periodic = 1; ++ } else { ++ st->fsm = FIQ_PER_SPLIT_HS_ABORTED; ++ start_next_periodic = 1; ++ } ++ /* We can now queue the next isochronous OUT transaction, if one is pending. */ ++ if(fiq_fsm_tt_next_isoc(state, num_channels, n)) { ++ fiq_print(FIQDBG_INT, state, "NEXTISO "); ++ } ++ break; ++ ++ case FIQ_PER_CSPLIT_NYET1: ++ /* First CSPLIT attempt was a NYET. If we get a subsequent NYET, ++ * we are too late and the TT has dropped its CSPLIT fifo. ++ */ ++ hfnum.d32 = FIQ_READ(state->dwc_regs_base + HFNUM); ++ hcchar.d32 = FIQ_READ(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR); ++ start_next_periodic = 1; ++ if (hcint.b.nak) { ++ st->fsm = FIQ_PER_SPLIT_DONE; ++ } else if (hcint.b.xfercomp) { ++ fiq_increment_dma_buf(state, num_channels, n); ++ st->fsm = FIQ_PER_CSPLIT_POLL; ++ st->nr_errors = 0; ++ if (fiq_fsm_more_csplits(state, n, &last_csplit)) { ++ handled = 1; ++ restart = 1; ++ if (!last_csplit) ++ start_next_periodic = 0; ++ } else { ++ st->fsm = FIQ_PER_SPLIT_DONE; ++ } ++ } else if (hcint.b.nyet) { ++ /* Doh. Data lost. */ ++ st->fsm = FIQ_PER_SPLIT_NYET_ABORTED; ++ } else if (hcint.b.xacterr || hcint.b.stall || hcint.b.bblerr) { ++ st->fsm = FIQ_PER_SPLIT_LS_ABORTED; ++ } else { ++ st->fsm = FIQ_PER_SPLIT_HS_ABORTED; ++ } ++ break; ++ ++ case FIQ_PER_CSPLIT_BROKEN_NYET1: ++ /* ++ * we got here because our host channel is in the delayed-interrupt ++ * state and we cannot take a NYET interrupt any later than when it ++ * occurred. Disable then re-enable the channel if this happens to force ++ * CSPLITs to occur at the right time. ++ */ ++ hfnum.d32 = FIQ_READ(state->dwc_regs_base + HFNUM); ++ hcchar.d32 = FIQ_READ(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR); ++ fiq_print(FIQDBG_INT, state, "BROK: %01d ", n); ++ if (hcint.b.nak) { ++ st->fsm = FIQ_PER_SPLIT_DONE; ++ start_next_periodic = 1; ++ } else if (hcint.b.xfercomp) { ++ fiq_increment_dma_buf(state, num_channels, n); ++ if (fiq_fsm_more_csplits(state, n, &last_csplit)) { ++ st->fsm = FIQ_PER_CSPLIT_POLL; ++ handled = 1; ++ restart = 1; ++ start_next_periodic = 1; ++ /* Reload HCTSIZ for the next transfer */ ++ fiq_fsm_reload_hctsiz(state, n); ++ if (!last_csplit) ++ start_next_periodic = 0; ++ } else { ++ st->fsm = FIQ_PER_SPLIT_DONE; ++ } ++ } else if (hcint.b.nyet) { ++ st->fsm = FIQ_PER_SPLIT_NYET_ABORTED; ++ start_next_periodic = 1; ++ } else if (hcint.b.xacterr || hcint.b.stall || hcint.b.bblerr) { ++ /* Local 3-strikes retry is handled by the core. This is a ERR response.*/ ++ st->fsm = FIQ_PER_SPLIT_LS_ABORTED; ++ } else { ++ st->fsm = FIQ_PER_SPLIT_HS_ABORTED; ++ } ++ break; ++ ++ case FIQ_PER_CSPLIT_POLL: ++ hfnum.d32 = FIQ_READ(state->dwc_regs_base + HFNUM); ++ hcchar.d32 = FIQ_READ(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCCHAR); ++ start_next_periodic = 1; ++ if (hcint.b.nak) { ++ st->fsm = FIQ_PER_SPLIT_DONE; ++ } else if (hcint.b.xfercomp) { ++ fiq_increment_dma_buf(state, num_channels, n); ++ if (fiq_fsm_more_csplits(state, n, &last_csplit)) { ++ handled = 1; ++ restart = 1; ++ /* Reload HCTSIZ for the next transfer */ ++ fiq_fsm_reload_hctsiz(state, n); ++ if (!last_csplit) ++ start_next_periodic = 0; ++ } else { ++ st->fsm = FIQ_PER_SPLIT_DONE; ++ } ++ } else if (hcint.b.nyet) { ++ /* Are we a NYET after the first data packet? */ ++ if (st->nrpackets == 0) { ++ st->fsm = FIQ_PER_CSPLIT_NYET1; ++ handled = 1; ++ restart = 1; ++ } else { ++ /* We got a NYET when polling CSPLITs. Can happen ++ * if our heuristic fails, or if someone disables us ++ * for any significant length of time. ++ */ ++ if (st->nr_errors >= 3) { ++ st->fsm = FIQ_PER_SPLIT_NYET_ABORTED; ++ } else { ++ st->fsm = FIQ_PER_SPLIT_DONE; ++ } ++ } ++ } else if (hcint.b.xacterr || hcint.b.stall || hcint.b.bblerr) { ++ /* For xacterr, Local 3-strikes retry is handled by the core. This is a ERR response.*/ ++ st->fsm = FIQ_PER_SPLIT_LS_ABORTED; ++ } else { ++ st->fsm = FIQ_PER_SPLIT_HS_ABORTED; ++ } ++ break; ++ ++ case FIQ_HS_ISOC_TURBO: ++ if (fiq_fsm_update_hs_isoc(state, n, hcint)) { ++ /* more transactions to come */ ++ handled = 1; ++ fiq_print(FIQDBG_INT, state, "HSISO M "); ++ /* For strided transfers, put ourselves to sleep */ ++ if (st->hs_isoc_info.stride > 1) { ++ st->uframe_sleeps = st->hs_isoc_info.stride - 1; ++ st->fsm = FIQ_HS_ISOC_SLEEPING; ++ } else { ++ restart = 1; ++ } ++ } else { ++ st->fsm = FIQ_HS_ISOC_DONE; ++ fiq_print(FIQDBG_INT, state, "HSISO F "); ++ } ++ break; ++ ++ case FIQ_HS_ISOC_ABORTED: ++ /* This abort is called by the driver rewriting the state mid-transaction ++ * which allows the dequeue mechanism to work more effectively. ++ */ ++ break; ++ ++ case FIQ_PER_ISO_OUT_ACTIVE: ++ if (hcint.b.ack) { ++ if(fiq_iso_out_advance(state, num_channels, n)) { ++ /* last OUT transfer */ ++ st->fsm = FIQ_PER_ISO_OUT_LAST; ++ /* ++ * Assuming the periodic FIFO in the dwc core ++ * actually does its job properly, we can queue ++ * the next ssplit now and in theory, the wire ++ * transactions will be in-order. ++ */ ++ // No it doesn't. It appears to process requests in host channel order. ++ //start_next_periodic = 1; ++ } ++ handled = 1; ++ restart = 1; ++ } else { ++ /* ++ * Isochronous transactions carry on regardless. Log the error ++ * and continue. ++ */ ++ //explode += 1; ++ st->nr_errors++; ++ if(fiq_iso_out_advance(state, num_channels, n)) { ++ st->fsm = FIQ_PER_ISO_OUT_LAST; ++ //start_next_periodic = 1; ++ } ++ handled = 1; ++ restart = 1; ++ } ++ break; ++ ++ case FIQ_PER_ISO_OUT_LAST: ++ if (hcint.b.ack) { ++ /* All done here */ ++ st->fsm = FIQ_PER_ISO_OUT_DONE; ++ } else { ++ st->fsm = FIQ_PER_ISO_OUT_DONE; ++ st->nr_errors++; ++ } ++ start_next_periodic = 1; ++ break; ++ ++ case FIQ_PER_SPLIT_TIMEOUT: ++ /* SOF kicked us because we overran. */ ++ start_next_periodic = 1; ++ break; ++ ++ default: ++ break; ++ } ++ ++ if (handled) { ++ FIQ_WRITE(state->dwc_regs_base + HC_START + (HC_OFFSET * n) + HCINT, hcint.d32); ++ } else { ++ /* Copy the regs into the state so the IRQ knows what to do */ ++ st->hcint_copy.d32 = hcint.d32; ++ } ++ ++ if (restart) { ++ /* Restart always implies handled. */ ++ if (restart == 2) { ++ /* For complete-split INs, the show must go on. ++ * Force a channel restart */ ++ fiq_fsm_restart_channel(state, n, 1); ++ } else { ++ fiq_fsm_restart_channel(state, n, 0); ++ } ++ } ++ if (start_next_periodic) { ++ fiq_fsm_start_next_periodic(state, num_channels); ++ } ++ if (st->fsm != FIQ_PASSTHROUGH) ++ fiq_print(FIQDBG_INT, state, "FSMOUT%02d", st->fsm); ++ ++ return handled; ++} ++ ++ ++/** ++ * dwc_otg_fiq_fsm() - Flying State Machine (monster) FIQ ++ * @state: pointer to state struct passed from the banked FIQ mode registers. ++ * @num_channels: set according to the DWC hardware configuration ++ * @dma: pointer to DMA bounce buffers for split transaction slots ++ * ++ * The FSM FIQ performs the low-level tasks that normally would be performed by the microcode ++ * inside an EHCI or similar host controller regarding split transactions. The DWC core ++ * interrupts each and every time a split transaction packet is received or sent successfully. ++ * This results in either an interrupt storm when everything is working "properly", or ++ * the interrupt latency of the system in general breaks time-sensitive periodic split ++ * transactions. Pushing the low-level, but relatively easy state machine work into the FIQ ++ * solves these problems. ++ * ++ * Return: void ++ */ ++void notrace dwc_otg_fiq_fsm(struct fiq_state *state, int num_channels) ++{ ++ gintsts_data_t gintsts, gintsts_handled; ++ gintmsk_data_t gintmsk; ++ //hfnum_data_t hfnum; ++ haint_data_t haint, haint_handled; ++ haintmsk_data_t haintmsk; ++ int kick_irq = 0; ++ ++ /* Ensure peripheral reads issued prior to FIQ entry are complete */ ++ dsb(sy); ++ ++ gintsts_handled.d32 = 0; ++ haint_handled.d32 = 0; ++ ++ fiq_fsm_spin_lock(&state->lock); ++ gintsts.d32 = FIQ_READ(state->dwc_regs_base + GINTSTS); ++ gintmsk.d32 = FIQ_READ(state->dwc_regs_base + GINTMSK); ++ gintsts.d32 &= gintmsk.d32; ++ ++ if (gintsts.b.sofintr) { ++ /* For FSM mode, SOF is required to keep the state machine advance for ++ * certain stages of the periodic pipeline. It's death to mask this ++ * interrupt in that case. ++ */ ++ ++ if (!fiq_fsm_do_sof(state, num_channels)) { ++ /* Kick IRQ once. Queue advancement means that all pending transactions ++ * will get serviced when the IRQ finally executes. ++ */ ++ if (state->gintmsk_saved.b.sofintr == 1) ++ kick_irq |= 1; ++ state->gintmsk_saved.b.sofintr = 0; ++ } ++ gintsts_handled.b.sofintr = 1; ++ } ++ ++ if (gintsts.b.hcintr) { ++ int i; ++ haint.d32 = FIQ_READ(state->dwc_regs_base + HAINT); ++ haintmsk.d32 = FIQ_READ(state->dwc_regs_base + HAINTMSK); ++ haint.d32 &= haintmsk.d32; ++ haint_handled.d32 = 0; ++ for (i=0; ihaintmsk_saved.b2.chint &= ~(1 << i); ++ } else { ++ /* do_hcintr cleaned up after itself, but clear haint */ ++ haint_handled.b2.chint |= (1 << i); ++ } ++ } ++ } ++ ++ if (haint_handled.b2.chint) { ++ FIQ_WRITE(state->dwc_regs_base + HAINT, haint_handled.d32); ++ } ++ ++ if (haintmsk.d32 != (haintmsk.d32 & state->haintmsk_saved.d32)) { ++ /* ++ * This is necessary to avoid multiple retriggers of the MPHI in the case ++ * where interrupts are held off and HCINTs start to pile up. ++ * Only wake up the IRQ if a new interrupt came in, was not handled and was ++ * masked. ++ */ ++ haintmsk.d32 &= state->haintmsk_saved.d32; ++ FIQ_WRITE(state->dwc_regs_base + HAINTMSK, haintmsk.d32); ++ kick_irq |= 1; ++ } ++ /* Top-Level interrupt - always handled because it's level-sensitive */ ++ gintsts_handled.b.hcintr = 1; ++ } ++ ++ ++ /* Clear the bits in the saved register that were not handled but were triggered. */ ++ state->gintmsk_saved.d32 &= ~(gintsts.d32 & ~gintsts_handled.d32); ++ ++ /* FIQ didn't handle something - mask has changed - write new mask */ ++ if (gintmsk.d32 != (gintmsk.d32 & state->gintmsk_saved.d32)) { ++ gintmsk.d32 &= state->gintmsk_saved.d32; ++ gintmsk.b.sofintr = 1; ++ FIQ_WRITE(state->dwc_regs_base + GINTMSK, gintmsk.d32); ++// fiq_print(FIQDBG_INT, state, "KICKGINT"); ++// fiq_print(FIQDBG_INT, state, "%08x", gintmsk.d32); ++// fiq_print(FIQDBG_INT, state, "%08x", state->gintmsk_saved.d32); ++ kick_irq |= 1; ++ } ++ ++ if (gintsts_handled.d32) { ++ /* Only applies to edge-sensitive bits in GINTSTS */ ++ FIQ_WRITE(state->dwc_regs_base + GINTSTS, gintsts_handled.d32); ++ } ++ ++ /* We got an interrupt, didn't handle it. */ ++ if (kick_irq) { ++ state->mphi_int_count++; ++ if (state->mphi_regs.swirq_set) { ++ FIQ_WRITE(state->mphi_regs.swirq_set, 1); ++ } else { ++ FIQ_WRITE(state->mphi_regs.outdda, state->dummy_send_dma); ++ FIQ_WRITE(state->mphi_regs.outddb, (1<<29)); ++ } ++ ++ } ++ state->fiq_done++; ++ mb(); ++ fiq_fsm_spin_unlock(&state->lock); ++} ++ ++ ++/** ++ * dwc_otg_fiq_nop() - FIQ "lite" ++ * @state: pointer to state struct passed from the banked FIQ mode registers. ++ * ++ * The "nop" handler does not intervene on any interrupts other than SOF. ++ * It is limited in scope to deciding at each SOF if the IRQ SOF handler (which deals ++ * with non-periodic/periodic queues) needs to be kicked. ++ * ++ * This is done to hold off the SOF interrupt, which occurs at a rate of 8000 per second. ++ * ++ * Return: void ++ */ ++void notrace dwc_otg_fiq_nop(struct fiq_state *state) ++{ ++ gintsts_data_t gintsts, gintsts_handled; ++ gintmsk_data_t gintmsk; ++ hfnum_data_t hfnum; ++ ++ /* Ensure peripheral reads issued prior to FIQ entry are complete */ ++ dsb(sy); ++ ++ fiq_fsm_spin_lock(&state->lock); ++ hfnum.d32 = FIQ_READ(state->dwc_regs_base + HFNUM); ++ gintsts.d32 = FIQ_READ(state->dwc_regs_base + GINTSTS); ++ gintmsk.d32 = FIQ_READ(state->dwc_regs_base + GINTMSK); ++ gintsts.d32 &= gintmsk.d32; ++ gintsts_handled.d32 = 0; ++ ++ if (gintsts.b.sofintr) { ++ if (!state->kick_np_queues && ++ dwc_frame_num_gt(state->next_sched_frame, hfnum.b.frnum)) { ++ /* SOF handled, no work to do, just ACK interrupt */ ++ gintsts_handled.b.sofintr = 1; ++ } else { ++ /* Kick IRQ */ ++ state->gintmsk_saved.b.sofintr = 0; ++ } ++ } ++ ++ /* Reset handled interrupts */ ++ if(gintsts_handled.d32) { ++ FIQ_WRITE(state->dwc_regs_base + GINTSTS, gintsts_handled.d32); ++ } ++ ++ /* Clear the bits in the saved register that were not handled but were triggered. */ ++ state->gintmsk_saved.d32 &= ~(gintsts.d32 & ~gintsts_handled.d32); ++ ++ /* We got an interrupt, didn't handle it and want to mask it */ ++ if (~(state->gintmsk_saved.d32)) { ++ state->mphi_int_count++; ++ gintmsk.d32 &= state->gintmsk_saved.d32; ++ FIQ_WRITE(state->dwc_regs_base + GINTMSK, gintmsk.d32); ++ if (state->mphi_regs.swirq_set) { ++ FIQ_WRITE(state->mphi_regs.swirq_set, 1); ++ } else { ++ /* Force a clear before another dummy send */ ++ FIQ_WRITE(state->mphi_regs.intstat, (1<<29)); ++ FIQ_WRITE(state->mphi_regs.outdda, state->dummy_send_dma); ++ FIQ_WRITE(state->mphi_regs.outddb, (1<<29)); ++ } ++ } ++ state->fiq_done++; ++ mb(); ++ fiq_fsm_spin_unlock(&state->lock); ++} +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_fiq_fsm.h +@@ -0,0 +1,399 @@ ++/* ++ * dwc_otg_fiq_fsm.h - Finite state machine FIQ header definitions ++ * ++ * Copyright (c) 2013 Raspberry Pi Foundation ++ * ++ * Author: Jonathan Bell ++ * All rights reserved. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions are met: ++ * * Redistributions of source code must retain the above copyright ++ * notice, this list of conditions and the following disclaimer. ++ * * Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in the ++ * documentation and/or other materials provided with the distribution. ++ * * Neither the name of Raspberry Pi nor the ++ * names of its contributors may be used to endorse or promote products ++ * derived from this software without specific prior written permission. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ++ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED ++ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE ++ * DISCLAIMED. IN NO EVENT SHALL BE LIABLE FOR ANY ++ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; ++ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ++ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ * ++ * This FIQ implements functionality that performs split transactions on ++ * the dwc_otg hardware without any outside intervention. A split transaction ++ * is "queued" by nominating a specific host channel to perform the entirety ++ * of a split transaction. This FIQ will then perform the microframe-precise ++ * scheduling required in each phase of the transaction until completion. ++ * ++ * The FIQ functionality has been surgically implanted into the Synopsys ++ * vendor-provided driver. ++ * ++ */ ++ ++#ifndef DWC_OTG_FIQ_FSM_H_ ++#define DWC_OTG_FIQ_FSM_H_ ++ ++#include "dwc_otg_regs.h" ++#include "dwc_otg_cil.h" ++#include "dwc_otg_hcd.h" ++#include ++#include ++#include ++#include ++ ++#if 0 ++#define FLAME_ON(x) \ ++do { \ ++ int gpioreg; \ ++ \ ++ gpioreg = readl(__io_address(0x20200000+0x8)); \ ++ gpioreg &= ~(7 << (x-20)*3); \ ++ gpioreg |= 0x1 << (x-20)*3; \ ++ writel(gpioreg, __io_address(0x20200000+0x8)); \ ++ \ ++ writel(1< 1, SOF wakes up the isochronous FSM */ ++ FIQ_HS_ISOC_SLEEPING = 24, ++ FIQ_HS_ISOC_DONE = 25, ++ FIQ_HS_ISOC_ABORTED = 26, ++ FIQ_DEQUEUE_ISSUED = 30, ++ FIQ_TEST = 32, ++}; ++ ++struct fiq_stack { ++ int magic1; ++ uint8_t stack[2048]; ++ int magic2; ++}; ++ ++ ++/** ++ * struct fiq_dma_info - DMA bounce buffer utilisation information (per-channel) ++ * @index: Number of slots reported used for IN transactions / number of slots ++ * transmitted for an OUT transaction ++ * @slot_len[6]: Number of actual transfer bytes in each slot (255 if unused) ++ * ++ * Split transaction transfers can have variable length depending on other bus ++ * traffic. The OTG core DMA engine requires 4-byte aligned addresses therefore ++ * each transaction needs a guaranteed aligned address. A maximum of 6 split transfers ++ * can happen per-frame. ++ */ ++struct fiq_dma_info { ++ u8 index; ++ u8 slot_len[6]; ++}; ++ ++struct __attribute__((packed)) fiq_split_dma_slot { ++ u8 buf[188]; ++}; ++ ++struct fiq_dma_channel { ++ struct __attribute__((packed)) fiq_split_dma_slot index[6]; ++}; ++ ++struct fiq_dma_blob { ++ struct __attribute__((packed)) fiq_dma_channel channel[0]; ++}; ++ ++/** ++ * struct fiq_hs_isoc_info - USB2.0 isochronous data ++ * @iso_frame: Pointer to the array of OTG URB iso_frame_descs. ++ * @nrframes: Total length of iso_frame_desc array ++ * @index: Current index (FIQ-maintained) ++ * @stride: Interval in uframes between HS isoc transactions ++ */ ++struct fiq_hs_isoc_info { ++ struct dwc_otg_hcd_iso_packet_desc *iso_desc; ++ unsigned int nrframes; ++ unsigned int index; ++ unsigned int stride; ++}; ++ ++/** ++ * struct fiq_channel_state - FIQ state machine storage ++ * @fsm: Current state of the channel as understood by the FIQ ++ * @nr_errors: Number of transaction errors on this split-transaction ++ * @hub_addr: SSPLIT/CSPLIT destination hub ++ * @port_addr: SSPLIT/CSPLIT destination port - always 1 if single TT hub ++ * @nrpackets: For isoc OUT, the number of split-OUT packets to transmit. For ++ * split-IN, number of CSPLIT data packets that were received. ++ * @hcchar_copy: ++ * @hcsplt_copy: ++ * @hcintmsk_copy: ++ * @hctsiz_copy: Copies of the host channel registers. ++ * For use as scratch, or for returning state. ++ * ++ * The fiq_channel_state is state storage between interrupts for a host channel. The ++ * FSM state is stored here. Members of this structure must only be set up by the ++ * driver prior to enabling the FIQ for this host channel, and not touched until the FIQ ++ * has updated the state to either a COMPLETE state group or ABORT state group. ++ */ ++ ++struct fiq_channel_state { ++ enum fiq_fsm_state fsm; ++ unsigned int nr_errors; ++ unsigned int hub_addr; ++ unsigned int port_addr; ++ /* Hardware bug workaround: sometimes channel halt interrupts are ++ * delayed until the next SOF. Keep track of when we expected to get interrupted. */ ++ unsigned int expected_uframe; ++ /* number of uframes remaining (for interval > 1 HS isoc transfers) before next transfer */ ++ unsigned int uframe_sleeps; ++ /* in/out for communicating number of dma buffers used, or number of ISOC to do */ ++ unsigned int nrpackets; ++ struct fiq_dma_info dma_info; ++ struct fiq_hs_isoc_info hs_isoc_info; ++ /* Copies of HC registers - in/out communication from/to IRQ handler ++ * and for ease of channel setup. A bit of mungeing is performed - for ++ * example the hctsiz.b.maxp is _always_ the max packet size of the endpoint. ++ */ ++ hcchar_data_t hcchar_copy; ++ hcsplt_data_t hcsplt_copy; ++ hcint_data_t hcint_copy; ++ hcintmsk_data_t hcintmsk_copy; ++ hctsiz_data_t hctsiz_copy; ++ hcdma_data_t hcdma_copy; ++}; ++ ++/** ++ * struct fiq_state - top-level FIQ state machine storage ++ * @mphi_regs: virtual address of the MPHI peripheral register file ++ * @dwc_regs_base: virtual address of the base of the DWC core register file ++ * @dma_base: physical address for the base of the DMA bounce buffers ++ * @dummy_send: Scratch area for sending a fake message to the MPHI peripheral ++ * @gintmsk_saved: Top-level mask of interrupts that the FIQ has not handled. ++ * Used for determining which interrupts fired to set off the IRQ handler. ++ * @haintmsk_saved: Mask of interrupts from host channels that the FIQ did not handle internally. ++ * @np_count: Non-periodic transactions in the active queue ++ * @np_sent: Count of non-periodic transactions that have completed ++ * @next_sched_frame: For periodic transactions handled by the driver's SOF-driven queuing mechanism, ++ * this is the next frame on which a SOF interrupt is required. Used to hold off ++ * passing SOF through to the driver until necessary. ++ * @channel[n]: Per-channel FIQ state. Allocated during init depending on the number of host ++ * channels configured into the core logic. ++ * ++ * This is passed as the first argument to the dwc_otg_fiq_fsm top-level FIQ handler from the asm stub. ++ * It contains top-level state information. ++ */ ++struct fiq_state { ++ fiq_lock_t lock; ++ mphi_regs_t mphi_regs; ++ void *dwc_regs_base; ++ dma_addr_t dma_base; ++ struct fiq_dma_blob *fiq_dmab; ++ void *dummy_send; ++ dma_addr_t dummy_send_dma; ++ gintmsk_data_t gintmsk_saved; ++ haintmsk_data_t haintmsk_saved; ++ int mphi_int_count; ++ unsigned int fiq_done; ++ unsigned int kick_np_queues; ++ unsigned int next_sched_frame; ++#ifdef FIQ_DEBUG ++ char * buffer; ++ unsigned int bufsiz; ++#endif ++ struct fiq_channel_state channel[0]; ++}; ++ ++#ifdef CONFIG_ARM64 ++ ++#ifdef local_fiq_enable ++#undef local_fiq_enable ++#endif ++ ++#ifdef local_fiq_disable ++#undef local_fiq_disable ++#endif ++ ++extern void local_fiq_enable(void); ++ ++extern void local_fiq_disable(void); ++ ++#endif ++ ++extern void fiq_fsm_spin_lock(fiq_lock_t *lock); ++ ++extern void fiq_fsm_spin_unlock(fiq_lock_t *lock); ++ ++extern int fiq_fsm_too_late(struct fiq_state *st, int n); ++ ++extern int fiq_fsm_tt_in_use(struct fiq_state *st, int num_channels, int n); ++ ++extern void dwc_otg_fiq_fsm(struct fiq_state *state, int num_channels); ++ ++extern void dwc_otg_fiq_nop(struct fiq_state *state); ++ ++#endif /* DWC_OTG_FIQ_FSM_H_ */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_fiq_stub.S +@@ -0,0 +1,80 @@ ++/* ++ * dwc_otg_fiq_fsm.S - assembly stub for the FSM FIQ ++ * ++ * Copyright (c) 2013 Raspberry Pi Foundation ++ * ++ * Author: Jonathan Bell ++ * All rights reserved. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions are met: ++ * * Redistributions of source code must retain the above copyright ++ * notice, this list of conditions and the following disclaimer. ++ * * Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in the ++ * documentation and/or other materials provided with the distribution. ++ * * Neither the name of Raspberry Pi nor the ++ * names of its contributors may be used to endorse or promote products ++ * derived from this software without specific prior written permission. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ++ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED ++ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE ++ * DISCLAIMED. IN NO EVENT SHALL BE LIABLE FOR ANY ++ * DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; ++ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ++ * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ */ ++ ++ ++#include ++#include ++ ++ ++.text ++ ++.global _dwc_otg_fiq_stub_end; ++ ++/** ++ * _dwc_otg_fiq_stub() - entry copied to the FIQ vector page to allow ++ * a C-style function call with arguments from the FIQ banked registers. ++ * r0 = &hcd->fiq_state ++ * r1 = &hcd->num_channels ++ * r2 = &hcd->dma_buffers ++ * Tramples: r0, r1, r2, r4, fp, ip ++ */ ++ ++ENTRY(_dwc_otg_fiq_stub) ++ /* Stash unbanked regs - SP will have been set up for us */ ++ mov ip, sp; ++ stmdb sp!, {r0-r12, lr}; ++#ifdef FIQ_DEBUG ++ // Cycle profiling - read cycle counter at start ++ mrc p15, 0, r5, c15, c12, 1; ++#endif ++ /* r11 = fp, don't trample it */ ++ mov r4, fp; ++ /* set EABI frame size */ ++ sub fp, ip, #512; ++ ++ /* for fiq NOP mode - just need state */ ++ mov r0, r8; ++ /* r9 = num_channels */ ++ mov r1, r9; ++ /* r10 = struct *dma_bufs */ ++// mov r2, r10; ++ ++ /* r4 = &fiq_c_function */ ++ blx r4; ++#ifdef FIQ_DEBUG ++ mrc p15, 0, r4, c15, c12, 1; ++ subs r5, r5, r4; ++ // r5 is now the cycle count time for executing the FIQ. Store it somewhere? ++#endif ++ ldmia sp!, {r0-r12, lr}; ++ subs pc, lr, #4; ++_dwc_otg_fiq_stub_end: ++END(_dwc_otg_fiq_stub) +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd.c +@@ -0,0 +1,4356 @@ ++ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd.c $ ++ * $Revision: #104 $ ++ * $Date: 2011/10/24 $ ++ * $Change: 1871159 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++#ifndef DWC_DEVICE_ONLY ++ ++/** @file ++ * This file implements HCD Core. All code in this file is portable and doesn't ++ * use any OS specific functions. ++ * Interface provided by HCD Core is defined in ++ * header file. ++ */ ++ ++#include ++#include ++ ++#include "dwc_otg_hcd.h" ++#include "dwc_otg_regs.h" ++#include "dwc_otg_fiq_fsm.h" ++ ++extern bool microframe_schedule; ++extern uint16_t fiq_fsm_mask, nak_holdoff; ++ ++//#define DEBUG_HOST_CHANNELS ++#ifdef DEBUG_HOST_CHANNELS ++static int last_sel_trans_num_per_scheduled = 0; ++static int last_sel_trans_num_nonper_scheduled = 0; ++static int last_sel_trans_num_avail_hc_at_start = 0; ++static int last_sel_trans_num_avail_hc_at_end = 0; ++#endif /* DEBUG_HOST_CHANNELS */ ++ ++ ++dwc_otg_hcd_t *dwc_otg_hcd_alloc_hcd(void) ++{ ++ return DWC_ALLOC(sizeof(dwc_otg_hcd_t)); ++} ++ ++/** ++ * Connection timeout function. An OTG host is required to display a ++ * message if the device does not connect within 10 seconds. ++ */ ++void dwc_otg_hcd_connect_timeout(void *ptr) ++{ ++ DWC_DEBUGPL(DBG_HCDV, "%s(%p)\n", __func__, ptr); ++ DWC_PRINTF("Connect Timeout\n"); ++ __DWC_ERROR("Device Not Connected/Responding\n"); ++} ++ ++#if defined(DEBUG) ++static void dump_channel_info(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ if (qh->channel != NULL) { ++ dwc_hc_t *hc = qh->channel; ++ dwc_list_link_t *item; ++ dwc_otg_qh_t *qh_item; ++ int num_channels = hcd->core_if->core_params->host_channels; ++ int i; ++ ++ dwc_otg_hc_regs_t *hc_regs; ++ hcchar_data_t hcchar; ++ hcsplt_data_t hcsplt; ++ hctsiz_data_t hctsiz; ++ uint32_t hcdma; ++ ++ hc_regs = hcd->core_if->host_if->hc_regs[hc->hc_num]; ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ hcsplt.d32 = DWC_READ_REG32(&hc_regs->hcsplt); ++ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz); ++ hcdma = DWC_READ_REG32(&hc_regs->hcdma); ++ ++ DWC_PRINTF(" Assigned to channel %p:\n", hc); ++ DWC_PRINTF(" hcchar 0x%08x, hcsplt 0x%08x\n", hcchar.d32, ++ hcsplt.d32); ++ DWC_PRINTF(" hctsiz 0x%08x, hcdma 0x%08x\n", hctsiz.d32, ++ hcdma); ++ DWC_PRINTF(" dev_addr: %d, ep_num: %d, ep_is_in: %d\n", ++ hc->dev_addr, hc->ep_num, hc->ep_is_in); ++ DWC_PRINTF(" ep_type: %d\n", hc->ep_type); ++ DWC_PRINTF(" max_packet: %d\n", hc->max_packet); ++ DWC_PRINTF(" data_pid_start: %d\n", hc->data_pid_start); ++ DWC_PRINTF(" xfer_started: %d\n", hc->xfer_started); ++ DWC_PRINTF(" halt_status: %d\n", hc->halt_status); ++ DWC_PRINTF(" xfer_buff: %p\n", hc->xfer_buff); ++ DWC_PRINTF(" xfer_len: %d\n", hc->xfer_len); ++ DWC_PRINTF(" qh: %p\n", hc->qh); ++ DWC_PRINTF(" NP inactive sched:\n"); ++ DWC_LIST_FOREACH(item, &hcd->non_periodic_sched_inactive) { ++ qh_item = ++ DWC_LIST_ENTRY(item, dwc_otg_qh_t, qh_list_entry); ++ DWC_PRINTF(" %p\n", qh_item); ++ } ++ DWC_PRINTF(" NP active sched:\n"); ++ DWC_LIST_FOREACH(item, &hcd->non_periodic_sched_active) { ++ qh_item = ++ DWC_LIST_ENTRY(item, dwc_otg_qh_t, qh_list_entry); ++ DWC_PRINTF(" %p\n", qh_item); ++ } ++ DWC_PRINTF(" Channels: \n"); ++ for (i = 0; i < num_channels; i++) { ++ dwc_hc_t *hc = hcd->hc_ptr_array[i]; ++ DWC_PRINTF(" %2d: %p\n", i, hc); ++ } ++ } ++} ++#else ++#define dump_channel_info(hcd, qh) ++#endif /* DEBUG */ ++ ++/** ++ * Work queue function for starting the HCD when A-Cable is connected. ++ * The hcd_start() must be called in a process context. ++ */ ++static void hcd_start_func(void *_vp) ++{ ++ dwc_otg_hcd_t *hcd = (dwc_otg_hcd_t *) _vp; ++ ++ DWC_DEBUGPL(DBG_HCDV, "%s() %p\n", __func__, hcd); ++ if (hcd) { ++ hcd->fops->start(hcd); ++ } ++} ++ ++static void del_xfer_timers(dwc_otg_hcd_t * hcd) ++{ ++#ifdef DEBUG ++ int i; ++ int num_channels = hcd->core_if->core_params->host_channels; ++ for (i = 0; i < num_channels; i++) { ++ DWC_TIMER_CANCEL(hcd->core_if->hc_xfer_timer[i]); ++ } ++#endif ++} ++ ++static void del_timers(dwc_otg_hcd_t * hcd) ++{ ++ del_xfer_timers(hcd); ++ DWC_TIMER_CANCEL(hcd->conn_timer); ++} ++ ++/** ++ * Processes all the URBs in a single list of QHs. Completes them with ++ * -ESHUTDOWN and frees the QTD. ++ */ ++static void kill_urbs_in_qh_list(dwc_otg_hcd_t * hcd, dwc_list_link_t * qh_list) ++{ ++ dwc_list_link_t *qh_item, *qh_tmp; ++ dwc_otg_qh_t *qh; ++ dwc_otg_qtd_t *qtd, *qtd_tmp; ++ int quiesced = 0; ++ ++ DWC_LIST_FOREACH_SAFE(qh_item, qh_tmp, qh_list) { ++ qh = DWC_LIST_ENTRY(qh_item, dwc_otg_qh_t, qh_list_entry); ++ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp, ++ &qh->qtd_list, qtd_list_entry) { ++ qtd = DWC_CIRCLEQ_FIRST(&qh->qtd_list); ++ if (qtd->urb != NULL) { ++ hcd->fops->complete(hcd, qtd->urb->priv, ++ qtd->urb, -DWC_E_SHUTDOWN); ++ dwc_otg_hcd_qtd_remove_and_free(hcd, qtd, qh); ++ } ++ ++ } ++ if(qh->channel) { ++ int n = qh->channel->hc_num; ++ /* Using hcchar.chen == 1 is not a reliable test. ++ * It is possible that the channel has already halted ++ * but not yet been through the IRQ handler. ++ */ ++ if (fiq_fsm_enable && (hcd->fiq_state->channel[qh->channel->hc_num].fsm != FIQ_PASSTHROUGH)) { ++ qh->channel->halt_status = DWC_OTG_HC_XFER_URB_DEQUEUE; ++ qh->channel->halt_pending = 1; ++ if (hcd->fiq_state->channel[n].fsm == FIQ_HS_ISOC_TURBO || ++ hcd->fiq_state->channel[n].fsm == FIQ_HS_ISOC_SLEEPING) ++ hcd->fiq_state->channel[n].fsm = FIQ_HS_ISOC_ABORTED; ++ /* We're called from disconnect callback or in the middle of freeing the HCD here, ++ * so FIQ is disabled, top-level interrupts masked and we're holding the spinlock. ++ * No further URBs will be submitted, but wait 1 microframe for any previously ++ * submitted periodic DMA to finish. ++ */ ++ if (!quiesced) { ++ udelay(125); ++ quiesced = 1; ++ } ++ } else { ++ dwc_otg_hc_halt(hcd->core_if, qh->channel, ++ DWC_OTG_HC_XFER_URB_DEQUEUE); ++ } ++ qh->channel = NULL; ++ } ++ dwc_otg_hcd_qh_remove(hcd, qh); ++ } ++} ++ ++/** ++ * Responds with an error status of ESHUTDOWN to all URBs in the non-periodic ++ * and periodic schedules. The QTD associated with each URB is removed from ++ * the schedule and freed. This function may be called when a disconnect is ++ * detected or when the HCD is being stopped. ++ */ ++static void kill_all_urbs(dwc_otg_hcd_t * hcd) ++{ ++ kill_urbs_in_qh_list(hcd, &hcd->non_periodic_sched_inactive); ++ kill_urbs_in_qh_list(hcd, &hcd->non_periodic_sched_active); ++ kill_urbs_in_qh_list(hcd, &hcd->periodic_sched_inactive); ++ kill_urbs_in_qh_list(hcd, &hcd->periodic_sched_ready); ++ kill_urbs_in_qh_list(hcd, &hcd->periodic_sched_assigned); ++ kill_urbs_in_qh_list(hcd, &hcd->periodic_sched_queued); ++} ++ ++/** ++ * Start the connection timer. An OTG host is required to display a ++ * message if the device does not connect within 10 seconds. The ++ * timer is deleted if a port connect interrupt occurs before the ++ * timer expires. ++ */ ++static void dwc_otg_hcd_start_connect_timer(dwc_otg_hcd_t * hcd) ++{ ++ DWC_TIMER_SCHEDULE(hcd->conn_timer, 10000 /* 10 secs */ ); ++} ++ ++/** ++ * HCD Callback function for disconnect of the HCD. ++ * ++ * @param p void pointer to the struct usb_hcd ++ */ ++static int32_t dwc_otg_hcd_session_start_cb(void *p) ++{ ++ dwc_otg_hcd_t *dwc_otg_hcd; ++ DWC_DEBUGPL(DBG_HCDV, "%s(%p)\n", __func__, p); ++ dwc_otg_hcd = p; ++ dwc_otg_hcd_start_connect_timer(dwc_otg_hcd); ++ return 1; ++} ++ ++/** ++ * HCD Callback function for starting the HCD when A-Cable is ++ * connected. ++ * ++ * @param p void pointer to the struct usb_hcd ++ */ ++static int32_t dwc_otg_hcd_start_cb(void *p) ++{ ++ dwc_otg_hcd_t *dwc_otg_hcd = p; ++ dwc_otg_core_if_t *core_if; ++ hprt0_data_t hprt0; ++ ++ core_if = dwc_otg_hcd->core_if; ++ ++ if (core_if->op_state == B_HOST) { ++ /* ++ * Reset the port. During a HNP mode switch the reset ++ * needs to occur within 1ms and have a duration of at ++ * least 50ms. ++ */ ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtrst = 1; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ } ++ DWC_WORKQ_SCHEDULE_DELAYED(core_if->wq_otg, ++ hcd_start_func, dwc_otg_hcd, 50, ++ "start hcd"); ++ ++ return 1; ++} ++ ++/** ++ * HCD Callback function for disconnect of the HCD. ++ * ++ * @param p void pointer to the struct usb_hcd ++ */ ++static int32_t dwc_otg_hcd_disconnect_cb(void *p) ++{ ++ gintsts_data_t intr; ++ dwc_otg_hcd_t *dwc_otg_hcd = p; ++ ++ DWC_SPINLOCK(dwc_otg_hcd->lock); ++ /* ++ * Set status flags for the hub driver. ++ */ ++ dwc_otg_hcd->flags.b.port_connect_status_change = 1; ++ dwc_otg_hcd->flags.b.port_connect_status = 0; ++ if(fiq_enable) { ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&dwc_otg_hcd->fiq_state->lock); ++ } ++ /* ++ * Shutdown any transfers in process by clearing the Tx FIFO Empty ++ * interrupt mask and status bits and disabling subsequent host ++ * channel interrupts. ++ */ ++ intr.d32 = 0; ++ intr.b.nptxfempty = 1; ++ intr.b.ptxfempty = 1; ++ intr.b.hcintr = 1; ++ DWC_MODIFY_REG32(&dwc_otg_hcd->core_if->core_global_regs->gintmsk, ++ intr.d32, 0); ++ DWC_MODIFY_REG32(&dwc_otg_hcd->core_if->core_global_regs->gintsts, ++ intr.d32, 0); ++ ++ del_timers(dwc_otg_hcd); ++ ++ /* ++ * Turn off the vbus power only if the core has transitioned to device ++ * mode. If still in host mode, need to keep power on to detect a ++ * reconnection. ++ */ ++ if (dwc_otg_is_device_mode(dwc_otg_hcd->core_if)) { ++ if (dwc_otg_hcd->core_if->op_state != A_SUSPEND) { ++ hprt0_data_t hprt0 = {.d32 = 0 }; ++ DWC_PRINTF("Disconnect: PortPower off\n"); ++ hprt0.b.prtpwr = 0; ++ DWC_WRITE_REG32(dwc_otg_hcd->core_if->host_if->hprt0, ++ hprt0.d32); ++ } ++ ++ dwc_otg_disable_host_interrupts(dwc_otg_hcd->core_if); ++ } ++ ++ /* Respond with an error status to all URBs in the schedule. */ ++ kill_all_urbs(dwc_otg_hcd); ++ ++ if (dwc_otg_is_host_mode(dwc_otg_hcd->core_if)) { ++ /* Clean up any host channels that were in use. */ ++ int num_channels; ++ int i; ++ dwc_hc_t *channel; ++ dwc_otg_hc_regs_t *hc_regs; ++ hcchar_data_t hcchar; ++ ++ num_channels = dwc_otg_hcd->core_if->core_params->host_channels; ++ ++ if (!dwc_otg_hcd->core_if->dma_enable) { ++ /* Flush out any channel requests in slave mode. */ ++ for (i = 0; i < num_channels; i++) { ++ channel = dwc_otg_hcd->hc_ptr_array[i]; ++ if (DWC_CIRCLEQ_EMPTY_ENTRY ++ (channel, hc_list_entry)) { ++ hc_regs = ++ dwc_otg_hcd->core_if-> ++ host_if->hc_regs[i]; ++ hcchar.d32 = ++ DWC_READ_REG32(&hc_regs->hcchar); ++ if (hcchar.b.chen) { ++ hcchar.b.chen = 0; ++ hcchar.b.chdis = 1; ++ hcchar.b.epdir = 0; ++ DWC_WRITE_REG32 ++ (&hc_regs->hcchar, ++ hcchar.d32); ++ } ++ } ++ } ++ } ++ ++ if(fiq_fsm_enable) { ++ for(i=0; i < 128; i++) { ++ dwc_otg_hcd->hub_port[i] = 0; ++ } ++ } ++ } ++ ++ if(fiq_enable) { ++ fiq_fsm_spin_unlock(&dwc_otg_hcd->fiq_state->lock); ++ local_fiq_enable(); ++ } ++ ++ if (dwc_otg_hcd->fops->disconnect) { ++ dwc_otg_hcd->fops->disconnect(dwc_otg_hcd); ++ } ++ ++ DWC_SPINUNLOCK(dwc_otg_hcd->lock); ++ return 1; ++} ++ ++/** ++ * HCD Callback function for stopping the HCD. ++ * ++ * @param p void pointer to the struct usb_hcd ++ */ ++static int32_t dwc_otg_hcd_stop_cb(void *p) ++{ ++ dwc_otg_hcd_t *dwc_otg_hcd = p; ++ ++ DWC_DEBUGPL(DBG_HCDV, "%s(%p)\n", __func__, p); ++ dwc_otg_hcd_stop(dwc_otg_hcd); ++ return 1; ++} ++ ++#ifdef CONFIG_USB_DWC_OTG_LPM ++/** ++ * HCD Callback function for sleep of HCD. ++ * ++ * @param p void pointer to the struct usb_hcd ++ */ ++static int dwc_otg_hcd_sleep_cb(void *p) ++{ ++ dwc_otg_hcd_t *hcd = p; ++ ++ dwc_otg_hcd_free_hc_from_lpm(hcd); ++ ++ return 0; ++} ++#endif ++ ++ ++/** ++ * HCD Callback function for Remote Wakeup. ++ * ++ * @param p void pointer to the struct usb_hcd ++ */ ++static int dwc_otg_hcd_rem_wakeup_cb(void *p) ++{ ++ dwc_otg_hcd_t *hcd = p; ++ ++ if (hcd->core_if->lx_state == DWC_OTG_L2) { ++ hcd->flags.b.port_suspend_change = 1; ++ } ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ else { ++ hcd->flags.b.port_l1_change = 1; ++ } ++#endif ++ return 0; ++} ++ ++/** ++ * Halts the DWC_otg host mode operations in a clean manner. USB transfers are ++ * stopped. ++ */ ++void dwc_otg_hcd_stop(dwc_otg_hcd_t * hcd) ++{ ++ hprt0_data_t hprt0 = {.d32 = 0 }; ++ ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD STOP\n"); ++ ++ /* ++ * The root hub should be disconnected before this function is called. ++ * The disconnect will clear the QTD lists (via ..._hcd_urb_dequeue) ++ * and the QH lists (via ..._hcd_endpoint_disable). ++ */ ++ ++ /* Turn off all host-specific interrupts. */ ++ dwc_otg_disable_host_interrupts(hcd->core_if); ++ ++ /* Turn off the vbus power */ ++ DWC_PRINTF("PortPower off\n"); ++ hprt0.b.prtpwr = 0; ++ DWC_WRITE_REG32(hcd->core_if->host_if->hprt0, hprt0.d32); ++ dwc_mdelay(1); ++} ++ ++int dwc_otg_hcd_urb_enqueue(dwc_otg_hcd_t * hcd, ++ dwc_otg_hcd_urb_t * dwc_otg_urb, void **ep_handle, ++ int atomic_alloc) ++{ ++ int retval = 0; ++ uint8_t needs_scheduling = 0; ++ dwc_otg_transaction_type_e tr_type; ++ dwc_otg_qtd_t *qtd; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ hprt0_data_t hprt0 = { .d32 = 0 }; ++ ++#ifdef DEBUG /* integrity checks (Broadcom) */ ++ if (NULL == hcd->core_if) { ++ DWC_ERROR("**** DWC OTG HCD URB Enqueue - HCD has NULL core_if\n"); ++ /* No longer connected. */ ++ return -DWC_E_INVALID; ++ } ++#endif ++ if (!hcd->flags.b.port_connect_status) { ++ /* No longer connected. */ ++ DWC_ERROR("Not connected\n"); ++ return -DWC_E_NO_DEVICE; ++ } ++ ++ /* Some core configurations cannot support LS traffic on a FS root port */ ++ if ((hcd->fops->speed(hcd, dwc_otg_urb->priv) == USB_SPEED_LOW) && ++ (hcd->core_if->hwcfg2.b.fs_phy_type == 1) && ++ (hcd->core_if->hwcfg2.b.hs_phy_type == 1)) { ++ hprt0.d32 = DWC_READ_REG32(hcd->core_if->host_if->hprt0); ++ if (hprt0.b.prtspd == DWC_HPRT0_PRTSPD_FULL_SPEED) { ++ return -DWC_E_NO_DEVICE; ++ } ++ } ++ ++ qtd = dwc_otg_hcd_qtd_create(dwc_otg_urb, atomic_alloc); ++ if (qtd == NULL) { ++ DWC_ERROR("DWC OTG HCD URB Enqueue failed creating QTD\n"); ++ return -DWC_E_NO_MEMORY; ++ } ++#ifdef DEBUG /* integrity checks (Broadcom) */ ++ if (qtd->urb == NULL) { ++ DWC_ERROR("**** DWC OTG HCD URB Enqueue created QTD with no URBs\n"); ++ return -DWC_E_NO_MEMORY; ++ } ++ if (qtd->urb->priv == NULL) { ++ DWC_ERROR("**** DWC OTG HCD URB Enqueue created QTD URB with no URB handle\n"); ++ return -DWC_E_NO_MEMORY; ++ } ++#endif ++ intr_mask.d32 = DWC_READ_REG32(&hcd->core_if->core_global_regs->gintmsk); ++ if(!intr_mask.b.sofintr || fiq_enable) needs_scheduling = 1; ++ if((((dwc_otg_qh_t *)ep_handle)->ep_type == UE_BULK) && !(qtd->urb->flags & URB_GIVEBACK_ASAP)) ++ /* Do not schedule SG transactions until qtd has URB_GIVEBACK_ASAP set */ ++ needs_scheduling = 0; ++ ++ retval = dwc_otg_hcd_qtd_add(qtd, hcd, (dwc_otg_qh_t **) ep_handle, atomic_alloc); ++ // creates a new queue in ep_handle if it doesn't exist already ++ if (retval < 0) { ++ DWC_ERROR("DWC OTG HCD URB Enqueue failed adding QTD. " ++ "Error status %d\n", retval); ++ dwc_otg_hcd_qtd_free(qtd); ++ return retval; ++ } ++ ++ if(needs_scheduling) { ++ tr_type = dwc_otg_hcd_select_transactions(hcd); ++ if (tr_type != DWC_OTG_TRANSACTION_NONE) { ++ dwc_otg_hcd_queue_transactions(hcd, tr_type); ++ } ++ } ++ return retval; ++} ++ ++int dwc_otg_hcd_urb_dequeue(dwc_otg_hcd_t * hcd, ++ dwc_otg_hcd_urb_t * dwc_otg_urb) ++{ ++ dwc_otg_qh_t *qh; ++ dwc_otg_qtd_t *urb_qtd; ++ BUG_ON(!hcd); ++ BUG_ON(!dwc_otg_urb); ++ ++#ifdef DEBUG /* integrity checks (Broadcom) */ ++ ++ if (hcd == NULL) { ++ DWC_ERROR("**** DWC OTG HCD URB Dequeue has NULL HCD\n"); ++ return -DWC_E_INVALID; ++ } ++ if (dwc_otg_urb == NULL) { ++ DWC_ERROR("**** DWC OTG HCD URB Dequeue has NULL URB\n"); ++ return -DWC_E_INVALID; ++ } ++ if (dwc_otg_urb->qtd == NULL) { ++ DWC_ERROR("**** DWC OTG HCD URB Dequeue with NULL QTD\n"); ++ return -DWC_E_INVALID; ++ } ++ urb_qtd = dwc_otg_urb->qtd; ++ BUG_ON(!urb_qtd); ++ if (urb_qtd->qh == NULL) { ++ DWC_ERROR("**** DWC OTG HCD URB Dequeue with QTD with NULL Q handler\n"); ++ return -DWC_E_INVALID; ++ } ++#else ++ urb_qtd = dwc_otg_urb->qtd; ++ BUG_ON(!urb_qtd); ++#endif ++ qh = urb_qtd->qh; ++ BUG_ON(!qh); ++ if (CHK_DEBUG_LEVEL(DBG_HCDV | DBG_HCD_URB)) { ++ if (urb_qtd->in_process) { ++ dump_channel_info(hcd, qh); ++ } ++ } ++#ifdef DEBUG /* integrity checks (Broadcom) */ ++ if (hcd->core_if == NULL) { ++ DWC_ERROR("**** DWC OTG HCD URB Dequeue HCD has NULL core_if\n"); ++ return -DWC_E_INVALID; ++ } ++#endif ++ if (urb_qtd->in_process && qh->channel) { ++ /* The QTD is in process (it has been assigned to a channel). */ ++ if (hcd->flags.b.port_connect_status) { ++ int n = qh->channel->hc_num; ++ /* ++ * If still connected (i.e. in host mode), halt the ++ * channel so it can be used for other transfers. If ++ * no longer connected, the host registers can't be ++ * written to halt the channel since the core is in ++ * device mode. ++ */ ++ /* In FIQ FSM mode, we need to shut down carefully. ++ * The FIQ may attempt to restart a disabled channel */ ++ if (fiq_fsm_enable && (hcd->fiq_state->channel[n].fsm != FIQ_PASSTHROUGH)) { ++ int retries = 3; ++ int running = 0; ++ enum fiq_fsm_state state; ++ ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&hcd->fiq_state->lock); ++ qh->channel->halt_status = DWC_OTG_HC_XFER_URB_DEQUEUE; ++ qh->channel->halt_pending = 1; ++ if (hcd->fiq_state->channel[n].fsm == FIQ_HS_ISOC_TURBO || ++ hcd->fiq_state->channel[n].fsm == FIQ_HS_ISOC_SLEEPING) ++ hcd->fiq_state->channel[n].fsm = FIQ_HS_ISOC_ABORTED; ++ fiq_fsm_spin_unlock(&hcd->fiq_state->lock); ++ local_fiq_enable(); ++ ++ if (dwc_qh_is_non_per(qh)) { ++ do { ++ state = READ_ONCE(hcd->fiq_state->channel[n].fsm); ++ running = (state != FIQ_NP_SPLIT_DONE) && ++ (state != FIQ_NP_SPLIT_LS_ABORTED) && ++ (state != FIQ_NP_SPLIT_HS_ABORTED); ++ if (!running) ++ break; ++ udelay(125); ++ } while(--retries); ++ if (!retries) ++ DWC_WARN("Timed out waiting for FSM NP transfer to complete on %d", ++ qh->channel->hc_num); ++ } ++ } else { ++ dwc_otg_hc_halt(hcd->core_if, qh->channel, ++ DWC_OTG_HC_XFER_URB_DEQUEUE); ++ } ++ } ++ } ++ ++ /* ++ * Free the QTD and clean up the associated QH. Leave the QH in the ++ * schedule if it has any remaining QTDs. ++ */ ++ ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD URB Dequeue - " ++ "delete %sQueue handler\n", ++ hcd->core_if->dma_desc_enable?"DMA ":""); ++ if (!hcd->core_if->dma_desc_enable) { ++ uint8_t b = urb_qtd->in_process; ++ if (nak_holdoff && qh->do_split && dwc_qh_is_non_per(qh)) ++ qh->nak_frame = 0xFFFF; ++ dwc_otg_hcd_qtd_remove_and_free(hcd, urb_qtd, qh); ++ if (b) { ++ dwc_otg_hcd_qh_deactivate(hcd, qh, 0); ++ qh->channel = NULL; ++ } else if (DWC_CIRCLEQ_EMPTY(&qh->qtd_list)) { ++ dwc_otg_hcd_qh_remove(hcd, qh); ++ } ++ } else { ++ dwc_otg_hcd_qtd_remove_and_free(hcd, urb_qtd, qh); ++ } ++ return 0; ++} ++ ++int dwc_otg_hcd_endpoint_disable(dwc_otg_hcd_t * hcd, void *ep_handle, ++ int retry) ++{ ++ dwc_otg_qh_t *qh = (dwc_otg_qh_t *) ep_handle; ++ int retval = 0; ++ dwc_irqflags_t flags; ++ ++ if (retry < 0) { ++ retval = -DWC_E_INVALID; ++ goto done; ++ } ++ ++ if (!qh) { ++ retval = -DWC_E_INVALID; ++ goto done; ++ } ++ ++ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags); ++ ++ while (!DWC_CIRCLEQ_EMPTY(&qh->qtd_list) && retry) { ++ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags); ++ retry--; ++ dwc_msleep(5); ++ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags); ++ } ++ ++ dwc_otg_hcd_qh_remove(hcd, qh); ++ ++ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags); ++ /* ++ * Split dwc_otg_hcd_qh_remove_and_free() into qh_remove ++ * and qh_free to prevent stack dump on DWC_DMA_FREE() with ++ * irq_disabled (spinlock_irqsave) in dwc_otg_hcd_desc_list_free() ++ * and dwc_otg_hcd_frame_list_alloc(). ++ */ ++ dwc_otg_hcd_qh_free(hcd, qh); ++ ++done: ++ return retval; ++} ++ ++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,30) ++int dwc_otg_hcd_endpoint_reset(dwc_otg_hcd_t * hcd, void *ep_handle) ++{ ++ int retval = 0; ++ dwc_otg_qh_t *qh = (dwc_otg_qh_t *) ep_handle; ++ if (!qh) ++ return -DWC_E_INVALID; ++ ++ qh->data_toggle = DWC_OTG_HC_PID_DATA0; ++ return retval; ++} ++#endif ++ ++/** ++ * HCD Callback structure for handling mode switching. ++ */ ++static dwc_otg_cil_callbacks_t hcd_cil_callbacks = { ++ .start = dwc_otg_hcd_start_cb, ++ .stop = dwc_otg_hcd_stop_cb, ++ .disconnect = dwc_otg_hcd_disconnect_cb, ++ .session_start = dwc_otg_hcd_session_start_cb, ++ .resume_wakeup = dwc_otg_hcd_rem_wakeup_cb, ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ .sleep = dwc_otg_hcd_sleep_cb, ++#endif ++ .p = 0, ++}; ++ ++/** ++ * Reset tasklet function ++ */ ++static void reset_tasklet_func(void *data) ++{ ++ dwc_otg_hcd_t *dwc_otg_hcd = (dwc_otg_hcd_t *) data; ++ dwc_otg_core_if_t *core_if = dwc_otg_hcd->core_if; ++ hprt0_data_t hprt0; ++ ++ DWC_DEBUGPL(DBG_HCDV, "USB RESET tasklet called\n"); ++ ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtrst = 1; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ dwc_mdelay(60); ++ ++ hprt0.b.prtrst = 0; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ dwc_otg_hcd->flags.b.port_reset_change = 1; ++} ++ ++static void completion_tasklet_func(void *ptr) ++{ ++ dwc_otg_hcd_t *hcd = (dwc_otg_hcd_t *) ptr; ++ struct urb *urb; ++ urb_tq_entry_t *item; ++ dwc_irqflags_t flags; ++ ++ /* This could just be spin_lock_irq */ ++ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags); ++ while (!DWC_TAILQ_EMPTY(&hcd->completed_urb_list)) { ++ item = DWC_TAILQ_FIRST(&hcd->completed_urb_list); ++ urb = item->urb; ++ DWC_TAILQ_REMOVE(&hcd->completed_urb_list, item, ++ urb_tq_entries); ++ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags); ++ DWC_FREE(item); ++ ++ usb_hcd_giveback_urb(hcd->priv, urb, urb->status); ++ ++ ++ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags); ++ } ++ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags); ++ return; ++} ++ ++static void qh_list_free(dwc_otg_hcd_t * hcd, dwc_list_link_t * qh_list) ++{ ++ dwc_list_link_t *item; ++ dwc_otg_qh_t *qh; ++ dwc_irqflags_t flags; ++ ++ if (!qh_list->next) { ++ /* The list hasn't been initialized yet. */ ++ return; ++ } ++ /* ++ * Hold spinlock here. Not needed in that case if bellow ++ * function is being called from ISR ++ */ ++ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags); ++ /* Ensure there are no QTDs or URBs left. */ ++ kill_urbs_in_qh_list(hcd, qh_list); ++ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags); ++ ++ DWC_LIST_FOREACH(item, qh_list) { ++ qh = DWC_LIST_ENTRY(item, dwc_otg_qh_t, qh_list_entry); ++ dwc_otg_hcd_qh_remove_and_free(hcd, qh); ++ } ++} ++ ++/** ++ * Exit from Hibernation if Host did not detect SRP from connected SRP capable ++ * Device during SRP time by host power up. ++ */ ++void dwc_otg_hcd_power_up(void *ptr) ++{ ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ dwc_otg_core_if_t *core_if = (dwc_otg_core_if_t *) ptr; ++ ++ DWC_PRINTF("%s called\n", __FUNCTION__); ++ ++ if (!core_if->hibernation_suspend) { ++ DWC_PRINTF("Already exited from Hibernation\n"); ++ return; ++ } ++ ++ /* Switch on the voltage to the core */ ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Reset the core */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Disable power clamps */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnclmp = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ /* Remove reset the core signal */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnrstn = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Disable PMU interrupt */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ core_if->hibernation_suspend = 0; ++ ++ /* Disable PMU */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ dwc_udelay(10); ++ ++ /* Enable VBUS */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.dis_vbus = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, gpwrdn.d32, 0); ++ ++ core_if->op_state = A_HOST; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_hcd_start(core_if); ++} ++ ++void dwc_otg_cleanup_fiq_channel(dwc_otg_hcd_t *hcd, uint32_t num) ++{ ++ struct fiq_channel_state *st = &hcd->fiq_state->channel[num]; ++ struct fiq_dma_blob *blob = hcd->fiq_dmab; ++ int i; ++ ++ st->fsm = FIQ_PASSTHROUGH; ++ st->hcchar_copy.d32 = 0; ++ st->hcsplt_copy.d32 = 0; ++ st->hcint_copy.d32 = 0; ++ st->hcintmsk_copy.d32 = 0; ++ st->hctsiz_copy.d32 = 0; ++ st->hcdma_copy.d32 = 0; ++ st->nr_errors = 0; ++ st->hub_addr = 0; ++ st->port_addr = 0; ++ st->expected_uframe = 0; ++ st->nrpackets = 0; ++ st->dma_info.index = 0; ++ for (i = 0; i < 6; i++) ++ st->dma_info.slot_len[i] = 255; ++ st->hs_isoc_info.index = 0; ++ st->hs_isoc_info.iso_desc = NULL; ++ st->hs_isoc_info.nrframes = 0; ++ ++ DWC_MEMSET(&blob->channel[num].index[0], 0x6b, 1128); ++} ++ ++/** ++ * Frees secondary storage associated with the dwc_otg_hcd structure contained ++ * in the struct usb_hcd field. ++ */ ++static void dwc_otg_hcd_free(dwc_otg_hcd_t * dwc_otg_hcd) ++{ ++ struct device *dev = dwc_otg_hcd_to_dev(dwc_otg_hcd); ++ int i; ++ ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD FREE\n"); ++ ++ del_timers(dwc_otg_hcd); ++ ++ /* Free memory for QH/QTD lists */ ++ qh_list_free(dwc_otg_hcd, &dwc_otg_hcd->non_periodic_sched_inactive); ++ qh_list_free(dwc_otg_hcd, &dwc_otg_hcd->non_periodic_sched_active); ++ qh_list_free(dwc_otg_hcd, &dwc_otg_hcd->periodic_sched_inactive); ++ qh_list_free(dwc_otg_hcd, &dwc_otg_hcd->periodic_sched_ready); ++ qh_list_free(dwc_otg_hcd, &dwc_otg_hcd->periodic_sched_assigned); ++ qh_list_free(dwc_otg_hcd, &dwc_otg_hcd->periodic_sched_queued); ++ ++ /* Free memory for the host channels. */ ++ for (i = 0; i < MAX_EPS_CHANNELS; i++) { ++ dwc_hc_t *hc = dwc_otg_hcd->hc_ptr_array[i]; ++ ++#ifdef DEBUG ++ if (dwc_otg_hcd->core_if->hc_xfer_timer[i]) { ++ DWC_TIMER_FREE(dwc_otg_hcd->core_if->hc_xfer_timer[i]); ++ } ++#endif ++ if (hc != NULL) { ++ DWC_DEBUGPL(DBG_HCDV, "HCD Free channel #%i, hc=%p\n", ++ i, hc); ++ DWC_FREE(hc); ++ } ++ } ++ ++ if (dwc_otg_hcd->core_if->dma_enable) { ++ if (dwc_otg_hcd->status_buf_dma) { ++ DWC_DMA_FREE(dev, DWC_OTG_HCD_STATUS_BUF_SIZE, ++ dwc_otg_hcd->status_buf, ++ dwc_otg_hcd->status_buf_dma); ++ } ++ } else if (dwc_otg_hcd->status_buf != NULL) { ++ DWC_FREE(dwc_otg_hcd->status_buf); ++ } ++ DWC_SPINLOCK_FREE(dwc_otg_hcd->lock); ++ /* Set core_if's lock pointer to NULL */ ++ dwc_otg_hcd->core_if->lock = NULL; ++ ++ DWC_TIMER_FREE(dwc_otg_hcd->conn_timer); ++ DWC_TASK_FREE(dwc_otg_hcd->reset_tasklet); ++ DWC_TASK_FREE(dwc_otg_hcd->completion_tasklet); ++ DWC_DMA_FREE(dev, 16, dwc_otg_hcd->fiq_state->dummy_send, ++ dwc_otg_hcd->fiq_state->dummy_send_dma); ++ DWC_FREE(dwc_otg_hcd->fiq_state); ++ ++#ifdef DWC_DEV_SRPCAP ++ if (dwc_otg_hcd->core_if->power_down == 2 && ++ dwc_otg_hcd->core_if->pwron_timer) { ++ DWC_TIMER_FREE(dwc_otg_hcd->core_if->pwron_timer); ++ } ++#endif ++ DWC_FREE(dwc_otg_hcd); ++} ++ ++int dwc_otg_hcd_init(dwc_otg_hcd_t * hcd, dwc_otg_core_if_t * core_if) ++{ ++ struct device *dev = dwc_otg_hcd_to_dev(hcd); ++ int retval = 0; ++ int num_channels; ++ int i; ++ dwc_hc_t *channel; ++ ++#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_SPINLOCK)) ++ DWC_SPINLOCK_ALLOC_LINUX_DEBUG(hcd->lock); ++#else ++ hcd->lock = DWC_SPINLOCK_ALLOC(); ++#endif ++ DWC_DEBUGPL(DBG_HCDV, "init of HCD %p given core_if %p\n", ++ hcd, core_if); ++ if (!hcd->lock) { ++ DWC_ERROR("Could not allocate lock for pcd"); ++ DWC_FREE(hcd); ++ retval = -DWC_E_NO_MEMORY; ++ goto out; ++ } ++ hcd->core_if = core_if; ++ ++ /* Register the HCD CIL Callbacks */ ++ dwc_otg_cil_register_hcd_callbacks(hcd->core_if, ++ &hcd_cil_callbacks, hcd); ++ ++ /* Initialize the non-periodic schedule. */ ++ DWC_LIST_INIT(&hcd->non_periodic_sched_inactive); ++ DWC_LIST_INIT(&hcd->non_periodic_sched_active); ++ ++ /* Initialize the periodic schedule. */ ++ DWC_LIST_INIT(&hcd->periodic_sched_inactive); ++ DWC_LIST_INIT(&hcd->periodic_sched_ready); ++ DWC_LIST_INIT(&hcd->periodic_sched_assigned); ++ DWC_LIST_INIT(&hcd->periodic_sched_queued); ++ DWC_TAILQ_INIT(&hcd->completed_urb_list); ++ /* ++ * Create a host channel descriptor for each host channel implemented ++ * in the controller. Initialize the channel descriptor array. ++ */ ++ DWC_CIRCLEQ_INIT(&hcd->free_hc_list); ++ num_channels = hcd->core_if->core_params->host_channels; ++ DWC_MEMSET(hcd->hc_ptr_array, 0, sizeof(hcd->hc_ptr_array)); ++ for (i = 0; i < num_channels; i++) { ++ channel = DWC_ALLOC(sizeof(dwc_hc_t)); ++ if (channel == NULL) { ++ retval = -DWC_E_NO_MEMORY; ++ DWC_ERROR("%s: host channel allocation failed\n", ++ __func__); ++ dwc_otg_hcd_free(hcd); ++ goto out; ++ } ++ channel->hc_num = i; ++ hcd->hc_ptr_array[i] = channel; ++#ifdef DEBUG ++ hcd->core_if->hc_xfer_timer[i] = ++ DWC_TIMER_ALLOC("hc timer", hc_xfer_timeout, ++ &hcd->core_if->hc_xfer_info[i]); ++#endif ++ DWC_DEBUGPL(DBG_HCDV, "HCD Added channel #%d, hc=%p\n", i, ++ channel); ++ } ++ ++ if (fiq_enable) { ++ hcd->fiq_state = DWC_ALLOC(sizeof(struct fiq_state) + (sizeof(struct fiq_channel_state) * num_channels)); ++ if (!hcd->fiq_state) { ++ retval = -DWC_E_NO_MEMORY; ++ DWC_ERROR("%s: cannot allocate fiq_state structure\n", __func__); ++ dwc_otg_hcd_free(hcd); ++ goto out; ++ } ++ DWC_MEMSET(hcd->fiq_state, 0, (sizeof(struct fiq_state) + (sizeof(struct fiq_channel_state) * num_channels))); ++ ++#ifdef CONFIG_ARM64 ++ spin_lock_init(&hcd->fiq_state->lock); ++#endif ++ ++ for (i = 0; i < num_channels; i++) { ++ hcd->fiq_state->channel[i].fsm = FIQ_PASSTHROUGH; ++ } ++ hcd->fiq_state->dummy_send = DWC_DMA_ALLOC_ATOMIC(dev, 16, ++ &hcd->fiq_state->dummy_send_dma); ++ ++ hcd->fiq_stack = DWC_ALLOC(sizeof(struct fiq_stack)); ++ if (!hcd->fiq_stack) { ++ retval = -DWC_E_NO_MEMORY; ++ DWC_ERROR("%s: cannot allocate fiq_stack structure\n", __func__); ++ dwc_otg_hcd_free(hcd); ++ goto out; ++ } ++ hcd->fiq_stack->magic1 = 0xDEADBEEF; ++ hcd->fiq_stack->magic2 = 0xD00DFEED; ++ hcd->fiq_state->gintmsk_saved.d32 = ~0; ++ hcd->fiq_state->haintmsk_saved.b2.chint = ~0; ++ ++ /* This bit is terrible and uses no API, but necessary. The FIQ has no concept of DMA pools ++ * (and if it did, would be a lot slower). This allocates a chunk of memory (~9kiB for 8 host channels) ++ * for use as transaction bounce buffers in a 2-D array. Our access into this chunk is done by some ++ * moderately readable array casts. ++ */ ++ hcd->fiq_dmab = DWC_DMA_ALLOC(dev, (sizeof(struct fiq_dma_channel) * num_channels), &hcd->fiq_state->dma_base); ++ DWC_WARN("FIQ DMA bounce buffers: virt = %px dma = %pad len=%zu", ++ hcd->fiq_dmab, &hcd->fiq_state->dma_base, ++ sizeof(struct fiq_dma_channel) * num_channels); ++ ++ DWC_MEMSET(hcd->fiq_dmab, 0x6b, 9024); ++ ++ /* pointer for debug in fiq_print */ ++ hcd->fiq_state->fiq_dmab = hcd->fiq_dmab; ++ if (fiq_fsm_enable) { ++ int i; ++ for (i=0; i < hcd->core_if->core_params->host_channels; i++) { ++ dwc_otg_cleanup_fiq_channel(hcd, i); ++ } ++ DWC_PRINTF("FIQ FSM acceleration enabled for :\n%s%s%s%s", ++ (fiq_fsm_mask & 0x1) ? "Non-periodic Split Transactions\n" : "", ++ (fiq_fsm_mask & 0x2) ? "Periodic Split Transactions\n" : "", ++ (fiq_fsm_mask & 0x4) ? "High-Speed Isochronous Endpoints\n" : "", ++ (fiq_fsm_mask & 0x8) ? "Interrupt/Control Split Transaction hack enabled\n" : ""); ++ } ++ } ++ ++ /* Initialize the Connection timeout timer. */ ++ hcd->conn_timer = DWC_TIMER_ALLOC("Connection timer", ++ dwc_otg_hcd_connect_timeout, 0); ++ ++ printk(KERN_DEBUG "dwc_otg: Microframe scheduler %s\n", microframe_schedule ? "enabled":"disabled"); ++ if (microframe_schedule) ++ init_hcd_usecs(hcd); ++ ++ /* Initialize reset tasklet. */ ++ hcd->reset_tasklet = DWC_TASK_ALLOC("reset_tasklet", reset_tasklet_func, hcd); ++ ++ hcd->completion_tasklet = DWC_TASK_ALLOC("completion_tasklet", ++ completion_tasklet_func, hcd); ++#ifdef DWC_DEV_SRPCAP ++ if (hcd->core_if->power_down == 2) { ++ /* Initialize Power on timer for Host power up in case hibernation */ ++ hcd->core_if->pwron_timer = DWC_TIMER_ALLOC("PWRON TIMER", ++ dwc_otg_hcd_power_up, core_if); ++ } ++#endif ++ ++ /* ++ * Allocate space for storing data on status transactions. Normally no ++ * data is sent, but this space acts as a bit bucket. This must be ++ * done after usb_add_hcd since that function allocates the DMA buffer ++ * pool. ++ */ ++ if (hcd->core_if->dma_enable) { ++ hcd->status_buf = ++ DWC_DMA_ALLOC(dev, DWC_OTG_HCD_STATUS_BUF_SIZE, ++ &hcd->status_buf_dma); ++ } else { ++ hcd->status_buf = DWC_ALLOC(DWC_OTG_HCD_STATUS_BUF_SIZE); ++ } ++ if (!hcd->status_buf) { ++ retval = -DWC_E_NO_MEMORY; ++ DWC_ERROR("%s: status_buf allocation failed\n", __func__); ++ dwc_otg_hcd_free(hcd); ++ goto out; ++ } ++ ++ hcd->otg_port = 1; ++ hcd->frame_list = NULL; ++ hcd->frame_list_dma = 0; ++ hcd->periodic_qh_count = 0; ++ ++ DWC_MEMSET(hcd->hub_port, 0, sizeof(hcd->hub_port)); ++#ifdef FIQ_DEBUG ++ DWC_MEMSET(hcd->hub_port_alloc, -1, sizeof(hcd->hub_port_alloc)); ++#endif ++ ++out: ++ return retval; ++} ++ ++void dwc_otg_hcd_remove(dwc_otg_hcd_t * hcd) ++{ ++ /* Turn off all host-specific interrupts. */ ++ dwc_otg_disable_host_interrupts(hcd->core_if); ++ ++ dwc_otg_hcd_free(hcd); ++} ++ ++/** ++ * Initializes dynamic portions of the DWC_otg HCD state. ++ */ ++static void dwc_otg_hcd_reinit(dwc_otg_hcd_t * hcd) ++{ ++ int num_channels; ++ int i; ++ dwc_hc_t *channel; ++ dwc_hc_t *channel_tmp; ++ ++ hcd->flags.d32 = 0; ++ ++ hcd->non_periodic_qh_ptr = &hcd->non_periodic_sched_active; ++ if (!microframe_schedule) { ++ hcd->non_periodic_channels = 0; ++ hcd->periodic_channels = 0; ++ } else { ++ hcd->available_host_channels = hcd->core_if->core_params->host_channels; ++ } ++ /* ++ * Put all channels in the free channel list and clean up channel ++ * states. ++ */ ++ DWC_CIRCLEQ_FOREACH_SAFE(channel, channel_tmp, ++ &hcd->free_hc_list, hc_list_entry) { ++ DWC_CIRCLEQ_REMOVE(&hcd->free_hc_list, channel, hc_list_entry); ++ } ++ ++ num_channels = hcd->core_if->core_params->host_channels; ++ for (i = 0; i < num_channels; i++) { ++ channel = hcd->hc_ptr_array[i]; ++ DWC_CIRCLEQ_INSERT_TAIL(&hcd->free_hc_list, channel, ++ hc_list_entry); ++ dwc_otg_hc_cleanup(hcd->core_if, channel); ++ } ++ ++ /* Initialize the DWC core for host mode operation. */ ++ dwc_otg_core_host_init(hcd->core_if); ++ ++ /* Set core_if's lock pointer to the hcd->lock */ ++ hcd->core_if->lock = hcd->lock; ++} ++ ++/** ++ * Assigns transactions from a QTD to a free host channel and initializes the ++ * host channel to perform the transactions. The host channel is removed from ++ * the free list. ++ * ++ * @param hcd The HCD state structure. ++ * @param qh Transactions from the first QTD for this QH are selected and ++ * assigned to a free host channel. ++ */ ++static void assign_and_init_hc(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ dwc_hc_t *hc; ++ dwc_otg_qtd_t *qtd; ++ dwc_otg_hcd_urb_t *urb; ++ void* ptr = NULL; ++ uint16_t wLength; ++ uint32_t intr_enable; ++ unsigned long flags; ++ gintmsk_data_t gintmsk = { .d32 = 0, }; ++ struct device *dev = dwc_otg_hcd_to_dev(hcd); ++ ++ qtd = DWC_CIRCLEQ_FIRST(&qh->qtd_list); ++ ++ urb = qtd->urb; ++ ++ DWC_DEBUGPL(DBG_HCDV, "%s(%p,%p) - urb %x, actual_length %d\n", __func__, hcd, qh, (unsigned int)urb, urb->actual_length); ++ ++ if (((urb->actual_length < 0) || (urb->actual_length > urb->length)) && !dwc_otg_hcd_is_pipe_in(&urb->pipe_info)) ++ urb->actual_length = urb->length; ++ ++ ++ hc = DWC_CIRCLEQ_FIRST(&hcd->free_hc_list); ++ ++ /* Remove the host channel from the free list. */ ++ DWC_CIRCLEQ_REMOVE_INIT(&hcd->free_hc_list, hc, hc_list_entry); ++ ++ qh->channel = hc; ++ ++ qtd->in_process = 1; ++ ++ /* ++ * Use usb_pipedevice to determine device address. This address is ++ * 0 before the SET_ADDRESS command and the correct address afterward. ++ */ ++ hc->dev_addr = dwc_otg_hcd_get_dev_addr(&urb->pipe_info); ++ hc->ep_num = dwc_otg_hcd_get_ep_num(&urb->pipe_info); ++ hc->speed = qh->dev_speed; ++ hc->max_packet = dwc_max_packet(qh->maxp); ++ ++ hc->xfer_started = 0; ++ hc->halt_status = DWC_OTG_HC_XFER_NO_HALT_STATUS; ++ hc->error_state = (qtd->error_count > 0); ++ hc->halt_on_queue = 0; ++ hc->halt_pending = 0; ++ hc->requests = 0; ++ ++ /* ++ * The following values may be modified in the transfer type section ++ * below. The xfer_len value may be reduced when the transfer is ++ * started to accommodate the max widths of the XferSize and PktCnt ++ * fields in the HCTSIZn register. ++ */ ++ ++ hc->ep_is_in = (dwc_otg_hcd_is_pipe_in(&urb->pipe_info) != 0); ++ if (hc->ep_is_in) { ++ hc->do_ping = 0; ++ } else { ++ hc->do_ping = qh->ping_state; ++ } ++ ++ hc->data_pid_start = qh->data_toggle; ++ hc->multi_count = 1; ++ ++ if (hcd->core_if->dma_enable) { ++ hc->xfer_buff = (uint8_t *) urb->dma + urb->actual_length; ++ ++ /* For non-dword aligned case */ ++ if (((unsigned long)hc->xfer_buff & 0x3) ++ && !hcd->core_if->dma_desc_enable) { ++ ptr = (uint8_t *) urb->buf + urb->actual_length; ++ } ++ } else { ++ hc->xfer_buff = (uint8_t *) urb->buf + urb->actual_length; ++ } ++ hc->xfer_len = urb->length - urb->actual_length; ++ hc->xfer_count = 0; ++ ++ /* ++ * Set the split attributes ++ */ ++ hc->do_split = 0; ++ if (qh->do_split) { ++ uint32_t hub_addr, port_addr; ++ hc->do_split = 1; ++ hc->start_pkt_count = 1; ++ hc->xact_pos = qtd->isoc_split_pos; ++ /* We don't need to do complete splits anymore */ ++// if(fiq_fsm_enable) ++ if (0) ++ hc->complete_split = qtd->complete_split = 0; ++ else ++ hc->complete_split = qtd->complete_split; ++ ++ hcd->fops->hub_info(hcd, urb->priv, &hub_addr, &port_addr); ++ hc->hub_addr = (uint8_t) hub_addr; ++ hc->port_addr = (uint8_t) port_addr; ++ } ++ ++ switch (dwc_otg_hcd_get_pipe_type(&urb->pipe_info)) { ++ case UE_CONTROL: ++ hc->ep_type = DWC_OTG_EP_TYPE_CONTROL; ++ switch (qtd->control_phase) { ++ case DWC_OTG_CONTROL_SETUP: ++ DWC_DEBUGPL(DBG_HCDV, " Control setup transaction\n"); ++ hc->do_ping = 0; ++ hc->ep_is_in = 0; ++ hc->data_pid_start = DWC_OTG_HC_PID_SETUP; ++ if (hcd->core_if->dma_enable) { ++ hc->xfer_buff = (uint8_t *) urb->setup_dma; ++ } else { ++ hc->xfer_buff = (uint8_t *) urb->setup_packet; ++ } ++ hc->xfer_len = 8; ++ ptr = NULL; ++ break; ++ case DWC_OTG_CONTROL_DATA: ++ DWC_DEBUGPL(DBG_HCDV, " Control data transaction\n"); ++ /* ++ * Hardware bug: small IN packets with length < 4 ++ * cause a 4-byte write to memory. We can only catch ++ * the case where we know a short packet is going to be ++ * returned in a control transfer, as the length is ++ * specified in the setup packet. This is only an issue ++ * for drivers that insist on packing a device's various ++ * properties into a struct and querying them one at a ++ * time (uvcvideo). ++ * Force the use of align_buf so that the subsequent ++ * memcpy puts the right number of bytes in the URB's ++ * buffer. ++ */ ++ wLength = ((uint16_t *)urb->setup_packet)[3]; ++ if (hc->ep_is_in && wLength < 4) ++ ptr = hc->xfer_buff; ++ ++ hc->data_pid_start = qtd->data_toggle; ++ break; ++ case DWC_OTG_CONTROL_STATUS: ++ /* ++ * Direction is opposite of data direction or IN if no ++ * data. ++ */ ++ DWC_DEBUGPL(DBG_HCDV, " Control status transaction\n"); ++ if (urb->length == 0) { ++ hc->ep_is_in = 1; ++ } else { ++ hc->ep_is_in = ++ dwc_otg_hcd_is_pipe_out(&urb->pipe_info); ++ } ++ if (hc->ep_is_in) { ++ hc->do_ping = 0; ++ } ++ ++ hc->data_pid_start = DWC_OTG_HC_PID_DATA1; ++ ++ hc->xfer_len = 0; ++ if (hcd->core_if->dma_enable) { ++ hc->xfer_buff = (uint8_t *) hcd->status_buf_dma; ++ } else { ++ hc->xfer_buff = (uint8_t *) hcd->status_buf; ++ } ++ ptr = NULL; ++ break; ++ } ++ break; ++ case UE_BULK: ++ hc->ep_type = DWC_OTG_EP_TYPE_BULK; ++ break; ++ case UE_INTERRUPT: ++ hc->ep_type = DWC_OTG_EP_TYPE_INTR; ++ break; ++ case UE_ISOCHRONOUS: ++ { ++ struct dwc_otg_hcd_iso_packet_desc *frame_desc; ++ ++ hc->ep_type = DWC_OTG_EP_TYPE_ISOC; ++ ++ if (hcd->core_if->dma_desc_enable) ++ break; ++ ++ frame_desc = &urb->iso_descs[qtd->isoc_frame_index]; ++ ++ frame_desc->status = 0; ++ ++ if (hcd->core_if->dma_enable) { ++ hc->xfer_buff = (uint8_t *) urb->dma; ++ } else { ++ hc->xfer_buff = (uint8_t *) urb->buf; ++ } ++ hc->xfer_buff += ++ frame_desc->offset + qtd->isoc_split_offset; ++ hc->xfer_len = ++ frame_desc->length - qtd->isoc_split_offset; ++ ++ /* For non-dword aligned buffers */ ++ if (((unsigned long)hc->xfer_buff & 0x3) ++ && hcd->core_if->dma_enable) { ++ ptr = ++ (uint8_t *) urb->buf + frame_desc->offset + ++ qtd->isoc_split_offset; ++ } else ++ ptr = NULL; ++ ++ if (hc->xact_pos == DWC_HCSPLIT_XACTPOS_ALL) { ++ if (hc->xfer_len <= 188) { ++ hc->xact_pos = DWC_HCSPLIT_XACTPOS_ALL; ++ } else { ++ hc->xact_pos = ++ DWC_HCSPLIT_XACTPOS_BEGIN; ++ } ++ } ++ } ++ break; ++ } ++ /* non DWORD-aligned buffer case */ ++ if (ptr) { ++ uint32_t buf_size; ++ if (hc->ep_type != DWC_OTG_EP_TYPE_ISOC) { ++ buf_size = hcd->core_if->core_params->max_transfer_size; ++ } else { ++ buf_size = 4096; ++ } ++ if (!qh->dw_align_buf) { ++ qh->dw_align_buf = DWC_DMA_ALLOC_ATOMIC(dev, buf_size, ++ &qh->dw_align_buf_dma); ++ if (!qh->dw_align_buf) { ++ DWC_ERROR ++ ("%s: Failed to allocate memory to handle " ++ "non-dword aligned buffer case\n", ++ __func__); ++ return; ++ } ++ } ++ if (!hc->ep_is_in) { ++ dwc_memcpy(qh->dw_align_buf, ptr, hc->xfer_len); ++ } ++ hc->align_buff = qh->dw_align_buf_dma; ++ } else { ++ hc->align_buff = 0; ++ } ++ ++ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR || ++ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) { ++ /* ++ * This value may be modified when the transfer is started to ++ * reflect the actual transfer length. ++ */ ++ hc->multi_count = dwc_hb_mult(qh->maxp); ++ } ++ ++ if (hcd->core_if->dma_desc_enable) ++ hc->desc_list_addr = qh->desc_list_dma; ++ ++ dwc_otg_hc_init(hcd->core_if, hc); ++ ++ local_irq_save(flags); ++ ++ if (fiq_enable) { ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&hcd->fiq_state->lock); ++ } ++ ++ /* Enable the top level host channel interrupt. */ ++ intr_enable = (1 << hc->hc_num); ++ DWC_MODIFY_REG32(&hcd->core_if->host_if->host_global_regs->haintmsk, 0, intr_enable); ++ ++ /* Make sure host channel interrupts are enabled. */ ++ gintmsk.b.hcintr = 1; ++ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, 0, gintmsk.d32); ++ ++ if (fiq_enable) { ++ fiq_fsm_spin_unlock(&hcd->fiq_state->lock); ++ local_fiq_enable(); ++ } ++ ++ local_irq_restore(flags); ++ hc->qh = qh; ++} ++ ++ ++/** ++ * fiq_fsm_transaction_suitable() - Test a QH for compatibility with the FIQ ++ * @hcd: Pointer to the dwc_otg_hcd struct ++ * @qh: pointer to the endpoint's queue head ++ * ++ * Transaction start/end control flow is grafted onto the existing dwc_otg ++ * mechanisms, to avoid spaghettifying the functions more than they already are. ++ * This function's eligibility check is altered by debug parameter. ++ * ++ * Returns: 0 for unsuitable, 1 implies the FIQ can be enabled for this transaction. ++ */ ++ ++int fiq_fsm_transaction_suitable(dwc_otg_hcd_t *hcd, dwc_otg_qh_t *qh) ++{ ++ if (qh->do_split) { ++ switch (qh->ep_type) { ++ case UE_CONTROL: ++ case UE_BULK: ++ if (fiq_fsm_mask & (1 << 0)) ++ return 1; ++ break; ++ case UE_INTERRUPT: ++ case UE_ISOCHRONOUS: ++ if (fiq_fsm_mask & (1 << 1)) ++ return 1; ++ break; ++ default: ++ break; ++ } ++ } else if (qh->ep_type == UE_ISOCHRONOUS) { ++ if (fiq_fsm_mask & (1 << 2)) { ++ /* ISOCH support. We test for compatibility: ++ * - DWORD aligned buffers ++ * - Must be at least 2 transfers (otherwise pointless to use the FIQ) ++ * If yes, then the fsm enqueue function will handle the state machine setup. ++ */ ++ dwc_otg_qtd_t *qtd = DWC_CIRCLEQ_FIRST(&qh->qtd_list); ++ dwc_otg_hcd_urb_t *urb = qtd->urb; ++ dwc_dma_t ptr; ++ int i; ++ ++ if (urb->packet_count < 2) ++ return 0; ++ for (i = 0; i < urb->packet_count; i++) { ++ ptr = urb->dma + urb->iso_descs[i].offset; ++ if (ptr & 0x3) ++ return 0; ++ } ++ return 1; ++ } ++ } ++ return 0; ++} ++ ++/** ++ * fiq_fsm_setup_periodic_dma() - Set up DMA bounce buffers ++ * @hcd: Pointer to the dwc_otg_hcd struct ++ * @qh: Pointer to the endpoint's queue head ++ * ++ * Periodic split transactions are transmitted modulo 188 bytes. ++ * This necessitates slicing data up into buckets for isochronous out ++ * and fixing up the DMA address for all IN transfers. ++ * ++ * Returns 1 if the DMA bounce buffers have been used, 0 if the default ++ * HC buffer has been used. ++ */ ++int fiq_fsm_setup_periodic_dma(dwc_otg_hcd_t *hcd, struct fiq_channel_state *st, dwc_otg_qh_t *qh) ++ { ++ int frame_length, i = 0; ++ uint8_t *ptr = NULL; ++ dwc_hc_t *hc = qh->channel; ++ struct fiq_dma_blob *blob; ++ struct dwc_otg_hcd_iso_packet_desc *frame_desc; ++ ++ for (i = 0; i < 6; i++) { ++ st->dma_info.slot_len[i] = 255; ++ } ++ st->dma_info.index = 0; ++ i = 0; ++ if (hc->ep_is_in) { ++ /* ++ * Set dma_regs to bounce buffer. FIQ will update the ++ * state depending on transaction progress. ++ * Pointer arithmetic on hcd->fiq_state->dma_base (a dma_addr_t) ++ * to point it to the correct offset in the allocated buffers. ++ */ ++ blob = (struct fiq_dma_blob *) hcd->fiq_state->dma_base; ++ st->hcdma_copy.d32 = (dma_addr_t) blob->channel[hc->hc_num].index[0].buf; ++ ++ /* Calculate the max number of CSPLITS such that the FIQ can time out ++ * a transaction if it fails. ++ */ ++ frame_length = st->hcchar_copy.b.mps; ++ do { ++ i++; ++ frame_length -= 188; ++ } while (frame_length >= 0); ++ st->nrpackets = i; ++ return 1; ++ } else { ++ if (qh->ep_type == UE_ISOCHRONOUS) { ++ ++ dwc_otg_qtd_t *qtd = DWC_CIRCLEQ_FIRST(&qh->qtd_list); ++ ++ frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index]; ++ frame_length = frame_desc->length; ++ ++ /* Virtual address for bounce buffers */ ++ blob = hcd->fiq_dmab; ++ ++ ptr = qtd->urb->buf + frame_desc->offset; ++ if (frame_length == 0) { ++ /* ++ * for isochronous transactions, we must still transmit a packet ++ * even if the length is zero. ++ */ ++ st->dma_info.slot_len[0] = 0; ++ st->nrpackets = 1; ++ } else { ++ do { ++ if (frame_length <= 188) { ++ dwc_memcpy(&blob->channel[hc->hc_num].index[i].buf[0], ptr, frame_length); ++ st->dma_info.slot_len[i] = frame_length; ++ ptr += frame_length; ++ } else { ++ dwc_memcpy(&blob->channel[hc->hc_num].index[i].buf[0], ptr, 188); ++ st->dma_info.slot_len[i] = 188; ++ ptr += 188; ++ } ++ i++; ++ frame_length -= 188; ++ } while (frame_length > 0); ++ st->nrpackets = i; ++ } ++ ptr = qtd->urb->buf + frame_desc->offset; ++ /* ++ * Point the HC at the DMA address of the bounce buffers ++ * ++ * Pointer arithmetic on hcd->fiq_state->dma_base (a ++ * dma_addr_t) to point it to the correct offset in the ++ * allocated buffers. ++ */ ++ blob = (struct fiq_dma_blob *) hcd->fiq_state->dma_base; ++ st->hcdma_copy.d32 = (dma_addr_t) blob->channel[hc->hc_num].index[0].buf; ++ ++ /* fixup xfersize to the actual packet size */ ++ st->hctsiz_copy.b.pid = 0; ++ st->hctsiz_copy.b.xfersize = st->dma_info.slot_len[0]; ++ return 1; ++ } else { ++ /* For interrupt, single OUT packet required, goes in the SSPLIT from hc_buff. */ ++ return 0; ++ } ++ } ++} ++ ++/** ++ * fiq_fsm_np_tt_contended() - Avoid performing contended non-periodic transfers ++ * @hcd: Pointer to the dwc_otg_hcd struct ++ * @qh: Pointer to the endpoint's queue head ++ * ++ * Certain hub chips don't differentiate between IN and OUT non-periodic pipes ++ * with the same endpoint number. If transfers get completed out of order ++ * (disregarding the direction token) then the hub can lock up ++ * or return erroneous responses. ++ * ++ * Returns 1 if initiating the transfer would cause contention, 0 otherwise. ++ */ ++int fiq_fsm_np_tt_contended(dwc_otg_hcd_t *hcd, dwc_otg_qh_t *qh) ++{ ++ int i; ++ struct fiq_channel_state *st; ++ int dev_addr = qh->channel->dev_addr; ++ int ep_num = qh->channel->ep_num; ++ for (i = 0; i < hcd->core_if->core_params->host_channels; i++) { ++ if (i == qh->channel->hc_num) ++ continue; ++ st = &hcd->fiq_state->channel[i]; ++ switch (st->fsm) { ++ case FIQ_NP_SSPLIT_STARTED: ++ case FIQ_NP_SSPLIT_RETRY: ++ case FIQ_NP_SSPLIT_PENDING: ++ case FIQ_NP_OUT_CSPLIT_RETRY: ++ case FIQ_NP_IN_CSPLIT_RETRY: ++ if (st->hcchar_copy.b.devaddr == dev_addr && ++ st->hcchar_copy.b.epnum == ep_num) ++ return 1; ++ break; ++ default: ++ break; ++ } ++ } ++ return 0; ++} ++ ++/* ++ * Pushing a periodic request into the queue near the EOF1 point ++ * in a microframe causes erroneous behaviour (frmovrun) interrupt. ++ * Usually, the request goes out on the bus causing a transfer but ++ * the core does not transfer the data to memory. ++ * This guard interval (in number of 60MHz clocks) is required which ++ * must cater for CPU latency between reading the value and enabling ++ * the channel. ++ */ ++#define PERIODIC_FRREM_BACKOFF 1000 ++ ++int fiq_fsm_queue_isoc_transaction(dwc_otg_hcd_t *hcd, dwc_otg_qh_t *qh) ++{ ++ dwc_hc_t *hc = qh->channel; ++ dwc_otg_hc_regs_t *hc_regs = hcd->core_if->host_if->hc_regs[hc->hc_num]; ++ dwc_otg_qtd_t *qtd = DWC_CIRCLEQ_FIRST(&qh->qtd_list); ++ int frame; ++ struct fiq_channel_state *st = &hcd->fiq_state->channel[hc->hc_num]; ++ int xfer_len, nrpackets; ++ hcdma_data_t hcdma; ++ hfnum_data_t hfnum; ++ ++ if (st->fsm != FIQ_PASSTHROUGH) ++ return 0; ++ ++ st->nr_errors = 0; ++ ++ st->hcchar_copy.d32 = 0; ++ st->hcchar_copy.b.mps = hc->max_packet; ++ st->hcchar_copy.b.epdir = hc->ep_is_in; ++ st->hcchar_copy.b.devaddr = hc->dev_addr; ++ st->hcchar_copy.b.epnum = hc->ep_num; ++ st->hcchar_copy.b.eptype = hc->ep_type; ++ ++ st->hcintmsk_copy.b.chhltd = 1; ++ ++ frame = dwc_otg_hcd_get_frame_number(hcd); ++ st->hcchar_copy.b.oddfrm = (frame & 0x1) ? 0 : 1; ++ ++ st->hcchar_copy.b.lspddev = 0; ++ /* Enable the channel later as a final register write. */ ++ ++ st->hcsplt_copy.d32 = 0; ++ ++ st->hs_isoc_info.iso_desc = (struct dwc_otg_hcd_iso_packet_desc *) &qtd->urb->iso_descs; ++ st->hs_isoc_info.nrframes = qtd->urb->packet_count; ++ /* grab the next DMA address offset from the array */ ++ st->hcdma_copy.d32 = qtd->urb->dma; ++ hcdma.d32 = st->hcdma_copy.d32 + st->hs_isoc_info.iso_desc[0].offset; ++ ++ /* We need to set multi_count. This is a bit tricky - has to be set per-transaction as ++ * the core needs to be told to send the correct number. Caution: for IN transfers, ++ * this is always set to the maximum size of the endpoint. */ ++ xfer_len = st->hs_isoc_info.iso_desc[0].length; ++ nrpackets = (xfer_len + st->hcchar_copy.b.mps - 1) / st->hcchar_copy.b.mps; ++ if (nrpackets == 0) ++ nrpackets = 1; ++ st->hcchar_copy.b.multicnt = nrpackets; ++ st->hctsiz_copy.b.pktcnt = nrpackets; ++ ++ /* Initial PID also needs to be set */ ++ if (st->hcchar_copy.b.epdir == 0) { ++ st->hctsiz_copy.b.xfersize = xfer_len; ++ switch (st->hcchar_copy.b.multicnt) { ++ case 1: ++ st->hctsiz_copy.b.pid = DWC_PID_DATA0; ++ break; ++ case 2: ++ case 3: ++ st->hctsiz_copy.b.pid = DWC_PID_MDATA; ++ break; ++ } ++ ++ } else { ++ st->hctsiz_copy.b.xfersize = nrpackets * st->hcchar_copy.b.mps; ++ switch (st->hcchar_copy.b.multicnt) { ++ case 1: ++ st->hctsiz_copy.b.pid = DWC_PID_DATA0; ++ break; ++ case 2: ++ st->hctsiz_copy.b.pid = DWC_PID_DATA1; ++ break; ++ case 3: ++ st->hctsiz_copy.b.pid = DWC_PID_DATA2; ++ break; ++ } ++ } ++ ++ st->hs_isoc_info.stride = qh->interval; ++ st->uframe_sleeps = 0; ++ ++ fiq_print(FIQDBG_INT, hcd->fiq_state, "FSMQ %01d ", hc->hc_num); ++ fiq_print(FIQDBG_INT, hcd->fiq_state, "%08x", st->hcchar_copy.d32); ++ fiq_print(FIQDBG_INT, hcd->fiq_state, "%08x", st->hctsiz_copy.d32); ++ fiq_print(FIQDBG_INT, hcd->fiq_state, "%08x", st->hcdma_copy.d32); ++ hfnum.d32 = DWC_READ_REG32(&hcd->core_if->host_if->host_global_regs->hfnum); ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&hcd->fiq_state->lock); ++ DWC_WRITE_REG32(&hc_regs->hctsiz, st->hctsiz_copy.d32); ++ DWC_WRITE_REG32(&hc_regs->hcsplt, st->hcsplt_copy.d32); ++ DWC_WRITE_REG32(&hc_regs->hcdma, st->hcdma_copy.d32); ++ DWC_WRITE_REG32(&hc_regs->hcchar, st->hcchar_copy.d32); ++ DWC_WRITE_REG32(&hc_regs->hcintmsk, st->hcintmsk_copy.d32); ++ if (hfnum.b.frrem < PERIODIC_FRREM_BACKOFF) { ++ /* Prevent queueing near EOF1. Bad things happen if a periodic ++ * split transaction is queued very close to EOF. SOF interrupt handler ++ * will wake this channel at the next interrupt. ++ */ ++ st->fsm = FIQ_HS_ISOC_SLEEPING; ++ st->uframe_sleeps = 1; ++ } else { ++ st->fsm = FIQ_HS_ISOC_TURBO; ++ st->hcchar_copy.b.chen = 1; ++ DWC_WRITE_REG32(&hc_regs->hcchar, st->hcchar_copy.d32); ++ } ++ mb(); ++ st->hcchar_copy.b.chen = 0; ++ fiq_fsm_spin_unlock(&hcd->fiq_state->lock); ++ local_fiq_enable(); ++ return 0; ++} ++ ++ ++/** ++ * fiq_fsm_queue_split_transaction() - Set up a host channel and FIQ state ++ * @hcd: Pointer to the dwc_otg_hcd struct ++ * @qh: Pointer to the endpoint's queue head ++ * ++ * This overrides the dwc_otg driver's normal method of queueing a transaction. ++ * Called from dwc_otg_hcd_queue_transactions(), this performs specific setup ++ * for the nominated host channel. ++ * ++ * For periodic transfers, it also peeks at the FIQ state to see if an immediate ++ * start is possible. If not, then the FIQ is left to start the transfer. ++ */ ++int fiq_fsm_queue_split_transaction(dwc_otg_hcd_t *hcd, dwc_otg_qh_t *qh) ++{ ++ int start_immediate = 1, i; ++ hfnum_data_t hfnum; ++ dwc_hc_t *hc = qh->channel; ++ dwc_otg_hc_regs_t *hc_regs = hcd->core_if->host_if->hc_regs[hc->hc_num]; ++ /* Program HC registers, setup FIQ_state, examine FIQ if periodic, start transfer (not if uframe 5) */ ++ int hub_addr, port_addr, frame, uframe; ++ struct fiq_channel_state *st = &hcd->fiq_state->channel[hc->hc_num]; ++ ++ /* ++ * Non-periodic channel assignments stay in the non_periodic_active queue. ++ * Therefore we get repeatedly called until the FIQ's done processing this channel. ++ */ ++ if (qh->channel->xfer_started == 1) ++ return 0; ++ ++ if (st->fsm != FIQ_PASSTHROUGH) { ++ pr_warn_ratelimited("%s:%d: Queue called for an active channel\n", __func__, __LINE__); ++ return 0; ++ } ++ ++ qh->channel->xfer_started = 1; ++ ++ st->nr_errors = 0; ++ ++ st->hcchar_copy.d32 = 0; ++ st->hcchar_copy.b.mps = min_t(uint32_t, hc->xfer_len, hc->max_packet); ++ st->hcchar_copy.b.epdir = hc->ep_is_in; ++ st->hcchar_copy.b.devaddr = hc->dev_addr; ++ st->hcchar_copy.b.epnum = hc->ep_num; ++ st->hcchar_copy.b.eptype = hc->ep_type; ++ if (hc->ep_type & 0x1) { ++ if (hc->ep_is_in) ++ st->hcchar_copy.b.multicnt = 3; ++ else ++ /* Docs say set this to 1, but driver sets to 0! */ ++ st->hcchar_copy.b.multicnt = 0; ++ } else { ++ st->hcchar_copy.b.multicnt = 1; ++ st->hcchar_copy.b.oddfrm = 0; ++ } ++ st->hcchar_copy.b.lspddev = (hc->speed == DWC_OTG_EP_SPEED_LOW) ? 1 : 0; ++ /* Enable the channel later as a final register write. */ ++ ++ st->hcsplt_copy.d32 = 0; ++ if(qh->do_split) { ++ hcd->fops->hub_info(hcd, DWC_CIRCLEQ_FIRST(&qh->qtd_list)->urb->priv, &hub_addr, &port_addr); ++ st->hcsplt_copy.b.compsplt = 0; ++ st->hcsplt_copy.b.spltena = 1; ++ // XACTPOS is for isoc-out only but needs initialising anyway. ++ st->hcsplt_copy.b.xactpos = ISOC_XACTPOS_ALL; ++ if((qh->ep_type == DWC_OTG_EP_TYPE_ISOC) && (!qh->ep_is_in)) { ++ /* For packetsize 0 < L < 188, ISOC_XACTPOS_ALL. ++ * for longer than this, ISOC_XACTPOS_BEGIN and the FIQ ++ * will update as necessary. ++ */ ++ if (hc->xfer_len > 188) { ++ st->hcsplt_copy.b.xactpos = ISOC_XACTPOS_BEGIN; ++ } ++ } ++ st->hcsplt_copy.b.hubaddr = (uint8_t) hub_addr; ++ st->hcsplt_copy.b.prtaddr = (uint8_t) port_addr; ++ st->hub_addr = hub_addr; ++ st->port_addr = port_addr; ++ } ++ ++ st->hctsiz_copy.d32 = 0; ++ st->hctsiz_copy.b.dopng = 0; ++ st->hctsiz_copy.b.pid = hc->data_pid_start; ++ ++ if (hc->ep_is_in || (hc->xfer_len > hc->max_packet)) { ++ hc->xfer_len = min_t(uint32_t, hc->xfer_len, hc->max_packet); ++ } else if (!hc->ep_is_in && (hc->xfer_len > 188)) { ++ hc->xfer_len = 188; ++ } ++ st->hctsiz_copy.b.xfersize = hc->xfer_len; ++ ++ st->hctsiz_copy.b.pktcnt = 1; ++ ++ if (hc->ep_type & 0x1) { ++ /* ++ * For potentially multi-packet transfers, must use the DMA bounce buffers. For IN transfers, ++ * the DMA address is the address of the first 188byte slot buffer in the bounce buffer array. ++ * For multi-packet OUT transfers, we need to copy the data into the bounce buffer array so the FIQ can punt ++ * the right address out as necessary. hc->xfer_buff and hc->xfer_len have already been set ++ * in assign_and_init_hc(), but this is for the eventual transaction completion only. The FIQ ++ * must not touch internal driver state. ++ */ ++ if(!fiq_fsm_setup_periodic_dma(hcd, st, qh)) { ++ if (hc->align_buff) { ++ st->hcdma_copy.d32 = hc->align_buff; ++ } else { ++ st->hcdma_copy.d32 = ((unsigned long) hc->xfer_buff & 0xFFFFFFFF); ++ } ++ } ++ } else { ++ if (hc->align_buff) { ++ st->hcdma_copy.d32 = hc->align_buff; ++ } else { ++ st->hcdma_copy.d32 = ((unsigned long) hc->xfer_buff & 0xFFFFFFFF); ++ } ++ } ++ /* The FIQ depends upon no other interrupts being enabled except channel halt. ++ * Fixup channel interrupt mask. */ ++ st->hcintmsk_copy.d32 = 0; ++ st->hcintmsk_copy.b.chhltd = 1; ++ st->hcintmsk_copy.b.ahberr = 1; ++ ++ /* Hack courtesy of FreeBSD: apparently forcing Interrupt Split transactions ++ * as Control puts the transfer into the non-periodic request queue and the ++ * non-periodic handler in the hub. Makes things lots easier. ++ */ ++ if ((fiq_fsm_mask & 0x8) && hc->ep_type == UE_INTERRUPT) { ++ st->hcchar_copy.b.multicnt = 0; ++ st->hcchar_copy.b.oddfrm = 0; ++ st->hcchar_copy.b.eptype = UE_CONTROL; ++ if (hc->align_buff) { ++ st->hcdma_copy.d32 = hc->align_buff; ++ } else { ++ st->hcdma_copy.d32 = ((unsigned long) hc->xfer_buff & 0xFFFFFFFF); ++ } ++ } ++ DWC_WRITE_REG32(&hc_regs->hcdma, st->hcdma_copy.d32); ++ DWC_WRITE_REG32(&hc_regs->hctsiz, st->hctsiz_copy.d32); ++ DWC_WRITE_REG32(&hc_regs->hcsplt, st->hcsplt_copy.d32); ++ DWC_WRITE_REG32(&hc_regs->hcchar, st->hcchar_copy.d32); ++ DWC_WRITE_REG32(&hc_regs->hcintmsk, st->hcintmsk_copy.d32); ++ ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&hcd->fiq_state->lock); ++ ++ if (hc->ep_type & 0x1) { ++ hfnum.d32 = DWC_READ_REG32(&hcd->core_if->host_if->host_global_regs->hfnum); ++ frame = (hfnum.b.frnum & ~0x7) >> 3; ++ uframe = hfnum.b.frnum & 0x7; ++ if (hfnum.b.frrem < PERIODIC_FRREM_BACKOFF) { ++ /* Prevent queueing near EOF1. Bad things happen if a periodic ++ * split transaction is queued very close to EOF. ++ */ ++ start_immediate = 0; ++ } else if (uframe == 5) { ++ start_immediate = 0; ++ } else if (hc->ep_type == UE_ISOCHRONOUS && !hc->ep_is_in) { ++ start_immediate = 0; ++ } else if (hc->ep_is_in && fiq_fsm_too_late(hcd->fiq_state, hc->hc_num)) { ++ start_immediate = 0; ++ } else { ++ /* Search through all host channels to determine if a transaction ++ * is currently in progress */ ++ for (i = 0; i < hcd->core_if->core_params->host_channels; i++) { ++ if (i == hc->hc_num || hcd->fiq_state->channel[i].fsm == FIQ_PASSTHROUGH) ++ continue; ++ switch (hcd->fiq_state->channel[i].fsm) { ++ /* TT is reserved for channels that are in the middle of a periodic ++ * split transaction. ++ */ ++ case FIQ_PER_SSPLIT_STARTED: ++ case FIQ_PER_CSPLIT_WAIT: ++ case FIQ_PER_CSPLIT_NYET1: ++ case FIQ_PER_CSPLIT_POLL: ++ case FIQ_PER_ISO_OUT_ACTIVE: ++ case FIQ_PER_ISO_OUT_LAST: ++ if (hcd->fiq_state->channel[i].hub_addr == hub_addr && ++ hcd->fiq_state->channel[i].port_addr == port_addr) { ++ start_immediate = 0; ++ } ++ break; ++ default: ++ break; ++ } ++ if (!start_immediate) ++ break; ++ } ++ } ++ } ++ if ((fiq_fsm_mask & 0x8) && hc->ep_type == UE_INTERRUPT) ++ start_immediate = 1; ++ ++ fiq_print(FIQDBG_INT, hcd->fiq_state, "FSMQ %01d %01d", hc->hc_num, start_immediate); ++ fiq_print(FIQDBG_INT, hcd->fiq_state, "%08d", hfnum.b.frrem); ++ //fiq_print(FIQDBG_INT, hcd->fiq_state, "H:%02dP:%02d", hub_addr, port_addr); ++ //fiq_print(FIQDBG_INT, hcd->fiq_state, "%08x", st->hctsiz_copy.d32); ++ //fiq_print(FIQDBG_INT, hcd->fiq_state, "%08x", st->hcdma_copy.d32); ++ switch (hc->ep_type) { ++ case UE_CONTROL: ++ case UE_BULK: ++ if (fiq_fsm_np_tt_contended(hcd, qh)) { ++ st->fsm = FIQ_NP_SSPLIT_PENDING; ++ start_immediate = 0; ++ } else { ++ st->fsm = FIQ_NP_SSPLIT_STARTED; ++ } ++ break; ++ case UE_ISOCHRONOUS: ++ if (hc->ep_is_in) { ++ if (start_immediate) { ++ st->fsm = FIQ_PER_SSPLIT_STARTED; ++ } else { ++ st->fsm = FIQ_PER_SSPLIT_QUEUED; ++ } ++ } else { ++ if (start_immediate) { ++ /* Single-isoc OUT packets don't require FIQ involvement */ ++ if (st->nrpackets == 1) { ++ st->fsm = FIQ_PER_ISO_OUT_LAST; ++ } else { ++ st->fsm = FIQ_PER_ISO_OUT_ACTIVE; ++ } ++ } else { ++ st->fsm = FIQ_PER_ISO_OUT_PENDING; ++ } ++ } ++ break; ++ case UE_INTERRUPT: ++ if (fiq_fsm_mask & 0x8) { ++ if (fiq_fsm_np_tt_contended(hcd, qh)) { ++ st->fsm = FIQ_NP_SSPLIT_PENDING; ++ start_immediate = 0; ++ } else { ++ st->fsm = FIQ_NP_SSPLIT_STARTED; ++ } ++ } else if (start_immediate) { ++ st->fsm = FIQ_PER_SSPLIT_STARTED; ++ } else { ++ st->fsm = FIQ_PER_SSPLIT_QUEUED; ++ } ++ default: ++ break; ++ } ++ if (start_immediate) { ++ /* Set the oddfrm bit as close as possible to actual queueing */ ++ frame = dwc_otg_hcd_get_frame_number(hcd); ++ st->expected_uframe = (frame + 1) & 0x3FFF; ++ st->hcchar_copy.b.oddfrm = (frame & 0x1) ? 0 : 1; ++ st->hcchar_copy.b.chen = 1; ++ DWC_WRITE_REG32(&hc_regs->hcchar, st->hcchar_copy.d32); ++ } ++ mb(); ++ fiq_fsm_spin_unlock(&hcd->fiq_state->lock); ++ local_fiq_enable(); ++ return 0; ++} ++ ++ ++/** ++ * This function selects transactions from the HCD transfer schedule and ++ * assigns them to available host channels. It is called from HCD interrupt ++ * handler functions. ++ * ++ * @param hcd The HCD state structure. ++ * ++ * @return The types of new transactions that were assigned to host channels. ++ */ ++dwc_otg_transaction_type_e dwc_otg_hcd_select_transactions(dwc_otg_hcd_t * hcd) ++{ ++ dwc_list_link_t *qh_ptr; ++ dwc_otg_qh_t *qh; ++ int num_channels; ++ dwc_otg_transaction_type_e ret_val = DWC_OTG_TRANSACTION_NONE; ++ ++#ifdef DEBUG_HOST_CHANNELS ++ last_sel_trans_num_per_scheduled = 0; ++ last_sel_trans_num_nonper_scheduled = 0; ++ last_sel_trans_num_avail_hc_at_start = hcd->available_host_channels; ++#endif /* DEBUG_HOST_CHANNELS */ ++ ++ /* Process entries in the periodic ready list. */ ++ qh_ptr = DWC_LIST_FIRST(&hcd->periodic_sched_ready); ++ ++ while (qh_ptr != &hcd->periodic_sched_ready && ++ !DWC_CIRCLEQ_EMPTY(&hcd->free_hc_list)) { ++ ++ qh = DWC_LIST_ENTRY(qh_ptr, dwc_otg_qh_t, qh_list_entry); ++ ++ if (microframe_schedule) { ++ // Make sure we leave one channel for non periodic transactions. ++ if (hcd->available_host_channels <= 1) { ++ break; ++ } ++ hcd->available_host_channels--; ++#ifdef DEBUG_HOST_CHANNELS ++ last_sel_trans_num_per_scheduled++; ++#endif /* DEBUG_HOST_CHANNELS */ ++ } ++ qh = DWC_LIST_ENTRY(qh_ptr, dwc_otg_qh_t, qh_list_entry); ++ assign_and_init_hc(hcd, qh); ++ ++ /* ++ * Move the QH from the periodic ready schedule to the ++ * periodic assigned schedule. ++ */ ++ qh_ptr = DWC_LIST_NEXT(qh_ptr); ++ DWC_LIST_MOVE_HEAD(&hcd->periodic_sched_assigned, ++ &qh->qh_list_entry); ++ } ++ ++ /* ++ * Process entries in the inactive portion of the non-periodic ++ * schedule. Some free host channels may not be used if they are ++ * reserved for periodic transfers. ++ */ ++ qh_ptr = hcd->non_periodic_sched_inactive.next; ++ num_channels = hcd->core_if->core_params->host_channels; ++ while (qh_ptr != &hcd->non_periodic_sched_inactive && ++ (microframe_schedule || hcd->non_periodic_channels < ++ num_channels - hcd->periodic_channels) && ++ !DWC_CIRCLEQ_EMPTY(&hcd->free_hc_list)) { ++ ++ qh = DWC_LIST_ENTRY(qh_ptr, dwc_otg_qh_t, qh_list_entry); ++ /* ++ * Check to see if this is a NAK'd retransmit, in which case ignore for retransmission ++ * we hold off on bulk retransmissions to reduce NAK interrupt overhead for full-speed ++ * cheeky devices that just hold off using NAKs ++ */ ++ if (fiq_enable && nak_holdoff && qh->do_split) { ++ if (qh->nak_frame != 0xffff) { ++ uint16_t next_frame = dwc_frame_num_inc(qh->nak_frame, (qh->ep_type == UE_BULK) ? nak_holdoff : 8); ++ uint16_t frame = dwc_otg_hcd_get_frame_number(hcd); ++ if (dwc_frame_num_le(frame, next_frame)) { ++ if(dwc_frame_num_le(next_frame, hcd->fiq_state->next_sched_frame)) { ++ hcd->fiq_state->next_sched_frame = next_frame; ++ } ++ qh_ptr = DWC_LIST_NEXT(qh_ptr); ++ continue; ++ } else { ++ qh->nak_frame = 0xFFFF; ++ } ++ } ++ } ++ ++ if (microframe_schedule) { ++ if (hcd->available_host_channels < 1) { ++ break; ++ } ++ hcd->available_host_channels--; ++#ifdef DEBUG_HOST_CHANNELS ++ last_sel_trans_num_nonper_scheduled++; ++#endif /* DEBUG_HOST_CHANNELS */ ++ } ++ ++ assign_and_init_hc(hcd, qh); ++ ++ /* ++ * Move the QH from the non-periodic inactive schedule to the ++ * non-periodic active schedule. ++ */ ++ qh_ptr = DWC_LIST_NEXT(qh_ptr); ++ DWC_LIST_MOVE_HEAD(&hcd->non_periodic_sched_active, ++ &qh->qh_list_entry); ++ ++ if (!microframe_schedule) ++ hcd->non_periodic_channels++; ++ } ++ /* we moved a non-periodic QH to the active schedule. If the inactive queue is empty, ++ * stop the FIQ from kicking us. We could potentially still have elements here if we ++ * ran out of host channels. ++ */ ++ if (fiq_enable) { ++ if (DWC_LIST_EMPTY(&hcd->non_periodic_sched_inactive)) { ++ hcd->fiq_state->kick_np_queues = 0; ++ } else { ++ /* For each entry remaining in the NP inactive queue, ++ * if this a NAK'd retransmit then don't set the kick flag. ++ */ ++ if(nak_holdoff) { ++ DWC_LIST_FOREACH(qh_ptr, &hcd->non_periodic_sched_inactive) { ++ qh = DWC_LIST_ENTRY(qh_ptr, dwc_otg_qh_t, qh_list_entry); ++ if (qh->nak_frame == 0xFFFF) { ++ hcd->fiq_state->kick_np_queues = 1; ++ } ++ } ++ } ++ } ++ } ++ if(!DWC_LIST_EMPTY(&hcd->periodic_sched_assigned)) ++ ret_val |= DWC_OTG_TRANSACTION_PERIODIC; ++ ++ if(!DWC_LIST_EMPTY(&hcd->non_periodic_sched_active)) ++ ret_val |= DWC_OTG_TRANSACTION_NON_PERIODIC; ++ ++ ++#ifdef DEBUG_HOST_CHANNELS ++ last_sel_trans_num_avail_hc_at_end = hcd->available_host_channels; ++#endif /* DEBUG_HOST_CHANNELS */ ++ return ret_val; ++} ++ ++/** ++ * Attempts to queue a single transaction request for a host channel ++ * associated with either a periodic or non-periodic transfer. This function ++ * assumes that there is space available in the appropriate request queue. For ++ * an OUT transfer or SETUP transaction in Slave mode, it checks whether space ++ * is available in the appropriate Tx FIFO. ++ * ++ * @param hcd The HCD state structure. ++ * @param hc Host channel descriptor associated with either a periodic or ++ * non-periodic transfer. ++ * @param fifo_dwords_avail Number of DWORDs available in the periodic Tx ++ * FIFO for periodic transfers or the non-periodic Tx FIFO for non-periodic ++ * transfers. ++ * ++ * @return 1 if a request is queued and more requests may be needed to ++ * complete the transfer, 0 if no more requests are required for this ++ * transfer, -1 if there is insufficient space in the Tx FIFO. ++ */ ++static int queue_transaction(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, uint16_t fifo_dwords_avail) ++{ ++ int retval; ++ ++ if (hcd->core_if->dma_enable) { ++ if (hcd->core_if->dma_desc_enable) { ++ if (!hc->xfer_started ++ || (hc->ep_type == DWC_OTG_EP_TYPE_ISOC)) { ++ dwc_otg_hcd_start_xfer_ddma(hcd, hc->qh); ++ hc->qh->ping_state = 0; ++ } ++ } else if (!hc->xfer_started) { ++ if (fiq_fsm_enable && hc->error_state) { ++ hcd->fiq_state->channel[hc->hc_num].nr_errors = ++ DWC_CIRCLEQ_FIRST(&hc->qh->qtd_list)->error_count; ++ hcd->fiq_state->channel[hc->hc_num].fsm = ++ FIQ_PASSTHROUGH_ERRORSTATE; ++ } ++ dwc_otg_hc_start_transfer(hcd->core_if, hc); ++ hc->qh->ping_state = 0; ++ } ++ retval = 0; ++ } else if (hc->halt_pending) { ++ /* Don't queue a request if the channel has been halted. */ ++ retval = 0; ++ } else if (hc->halt_on_queue) { ++ dwc_otg_hc_halt(hcd->core_if, hc, hc->halt_status); ++ retval = 0; ++ } else if (hc->do_ping) { ++ if (!hc->xfer_started) { ++ dwc_otg_hc_start_transfer(hcd->core_if, hc); ++ } ++ retval = 0; ++ } else if (!hc->ep_is_in || hc->data_pid_start == DWC_OTG_HC_PID_SETUP) { ++ if ((fifo_dwords_avail * 4) >= hc->max_packet) { ++ if (!hc->xfer_started) { ++ dwc_otg_hc_start_transfer(hcd->core_if, hc); ++ retval = 1; ++ } else { ++ retval = ++ dwc_otg_hc_continue_transfer(hcd->core_if, ++ hc); ++ } ++ } else { ++ retval = -1; ++ } ++ } else { ++ if (!hc->xfer_started) { ++ dwc_otg_hc_start_transfer(hcd->core_if, hc); ++ retval = 1; ++ } else { ++ retval = dwc_otg_hc_continue_transfer(hcd->core_if, hc); ++ } ++ } ++ ++ return retval; ++} ++ ++/** ++ * Processes periodic channels for the next frame and queues transactions for ++ * these channels to the DWC_otg controller. After queueing transactions, the ++ * Periodic Tx FIFO Empty interrupt is enabled if there are more transactions ++ * to queue as Periodic Tx FIFO or request queue space becomes available. ++ * Otherwise, the Periodic Tx FIFO Empty interrupt is disabled. ++ */ ++static void process_periodic_channels(dwc_otg_hcd_t * hcd) ++{ ++ hptxsts_data_t tx_status; ++ dwc_list_link_t *qh_ptr; ++ dwc_otg_qh_t *qh; ++ int status = 0; ++ int no_queue_space = 0; ++ int no_fifo_space = 0; ++ ++ dwc_otg_host_global_regs_t *host_regs; ++ host_regs = hcd->core_if->host_if->host_global_regs; ++ ++ DWC_DEBUGPL(DBG_HCDV, "Queue periodic transactions\n"); ++#ifdef DEBUG ++ tx_status.d32 = DWC_READ_REG32(&host_regs->hptxsts); ++ DWC_DEBUGPL(DBG_HCDV, ++ " P Tx Req Queue Space Avail (before queue): %d\n", ++ tx_status.b.ptxqspcavail); ++ DWC_DEBUGPL(DBG_HCDV, " P Tx FIFO Space Avail (before queue): %d\n", ++ tx_status.b.ptxfspcavail); ++#endif ++ ++ qh_ptr = hcd->periodic_sched_assigned.next; ++ while (qh_ptr != &hcd->periodic_sched_assigned) { ++ tx_status.d32 = DWC_READ_REG32(&host_regs->hptxsts); ++ if (tx_status.b.ptxqspcavail == 0) { ++ no_queue_space = 1; ++ break; ++ } ++ ++ qh = DWC_LIST_ENTRY(qh_ptr, dwc_otg_qh_t, qh_list_entry); ++ ++ // Do not send a split start transaction any later than frame .6 ++ // Note, we have to schedule a periodic in .5 to make it go in .6 ++ if(fiq_fsm_enable && qh->do_split && ((dwc_otg_hcd_get_frame_number(hcd) + 1) & 7) > 6) ++ { ++ qh_ptr = qh_ptr->next; ++ hcd->fiq_state->next_sched_frame = dwc_otg_hcd_get_frame_number(hcd) | 7; ++ continue; ++ } ++ ++ if (fiq_fsm_enable && fiq_fsm_transaction_suitable(hcd, qh)) { ++ if (qh->do_split) ++ fiq_fsm_queue_split_transaction(hcd, qh); ++ else ++ fiq_fsm_queue_isoc_transaction(hcd, qh); ++ } else { ++ ++ /* ++ * Set a flag if we're queueing high-bandwidth in slave mode. ++ * The flag prevents any halts to get into the request queue in ++ * the middle of multiple high-bandwidth packets getting queued. ++ */ ++ if (!hcd->core_if->dma_enable && qh->channel->multi_count > 1) { ++ hcd->core_if->queuing_high_bandwidth = 1; ++ } ++ status = queue_transaction(hcd, qh->channel, ++ tx_status.b.ptxfspcavail); ++ if (status < 0) { ++ no_fifo_space = 1; ++ break; ++ } ++ } ++ ++ /* ++ * In Slave mode, stay on the current transfer until there is ++ * nothing more to do or the high-bandwidth request count is ++ * reached. In DMA mode, only need to queue one request. The ++ * controller automatically handles multiple packets for ++ * high-bandwidth transfers. ++ */ ++ if (hcd->core_if->dma_enable || status == 0 || ++ qh->channel->requests == qh->channel->multi_count) { ++ qh_ptr = qh_ptr->next; ++ /* ++ * Move the QH from the periodic assigned schedule to ++ * the periodic queued schedule. ++ */ ++ DWC_LIST_MOVE_HEAD(&hcd->periodic_sched_queued, ++ &qh->qh_list_entry); ++ ++ /* done queuing high bandwidth */ ++ hcd->core_if->queuing_high_bandwidth = 0; ++ } ++ } ++ ++ if (!hcd->core_if->dma_enable) { ++ dwc_otg_core_global_regs_t *global_regs; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ global_regs = hcd->core_if->core_global_regs; ++ intr_mask.b.ptxfempty = 1; ++#ifdef DEBUG ++ tx_status.d32 = DWC_READ_REG32(&host_regs->hptxsts); ++ DWC_DEBUGPL(DBG_HCDV, ++ " P Tx Req Queue Space Avail (after queue): %d\n", ++ tx_status.b.ptxqspcavail); ++ DWC_DEBUGPL(DBG_HCDV, ++ " P Tx FIFO Space Avail (after queue): %d\n", ++ tx_status.b.ptxfspcavail); ++#endif ++ if (!DWC_LIST_EMPTY(&hcd->periodic_sched_assigned) || ++ no_queue_space || no_fifo_space) { ++ /* ++ * May need to queue more transactions as the request ++ * queue or Tx FIFO empties. Enable the periodic Tx ++ * FIFO empty interrupt. (Always use the half-empty ++ * level to ensure that new requests are loaded as ++ * soon as possible.) ++ */ ++ DWC_MODIFY_REG32(&global_regs->gintmsk, 0, ++ intr_mask.d32); ++ } else { ++ /* ++ * Disable the Tx FIFO empty interrupt since there are ++ * no more transactions that need to be queued right ++ * now. This function is called from interrupt ++ * handlers to queue more transactions as transfer ++ * states change. ++ */ ++ DWC_MODIFY_REG32(&global_regs->gintmsk, intr_mask.d32, ++ 0); ++ } ++ } ++} ++ ++/** ++ * Processes active non-periodic channels and queues transactions for these ++ * channels to the DWC_otg controller. After queueing transactions, the NP Tx ++ * FIFO Empty interrupt is enabled if there are more transactions to queue as ++ * NP Tx FIFO or request queue space becomes available. Otherwise, the NP Tx ++ * FIFO Empty interrupt is disabled. ++ */ ++static void process_non_periodic_channels(dwc_otg_hcd_t * hcd) ++{ ++ gnptxsts_data_t tx_status; ++ dwc_list_link_t *orig_qh_ptr; ++ dwc_otg_qh_t *qh; ++ int status; ++ int no_queue_space = 0; ++ int no_fifo_space = 0; ++ int more_to_do = 0; ++ ++ dwc_otg_core_global_regs_t *global_regs = ++ hcd->core_if->core_global_regs; ++ ++ DWC_DEBUGPL(DBG_HCDV, "Queue non-periodic transactions\n"); ++#ifdef DEBUG ++ tx_status.d32 = DWC_READ_REG32(&global_regs->gnptxsts); ++ DWC_DEBUGPL(DBG_HCDV, ++ " NP Tx Req Queue Space Avail (before queue): %d\n", ++ tx_status.b.nptxqspcavail); ++ DWC_DEBUGPL(DBG_HCDV, " NP Tx FIFO Space Avail (before queue): %d\n", ++ tx_status.b.nptxfspcavail); ++#endif ++ /* ++ * Keep track of the starting point. Skip over the start-of-list ++ * entry. ++ */ ++ if (hcd->non_periodic_qh_ptr == &hcd->non_periodic_sched_active) { ++ hcd->non_periodic_qh_ptr = hcd->non_periodic_qh_ptr->next; ++ } ++ orig_qh_ptr = hcd->non_periodic_qh_ptr; ++ ++ /* ++ * Process once through the active list or until no more space is ++ * available in the request queue or the Tx FIFO. ++ */ ++ do { ++ tx_status.d32 = DWC_READ_REG32(&global_regs->gnptxsts); ++ if (!hcd->core_if->dma_enable && tx_status.b.nptxqspcavail == 0) { ++ no_queue_space = 1; ++ break; ++ } ++ ++ qh = DWC_LIST_ENTRY(hcd->non_periodic_qh_ptr, dwc_otg_qh_t, ++ qh_list_entry); ++ ++ if(fiq_fsm_enable && fiq_fsm_transaction_suitable(hcd, qh)) { ++ fiq_fsm_queue_split_transaction(hcd, qh); ++ } else { ++ status = queue_transaction(hcd, qh->channel, ++ tx_status.b.nptxfspcavail); ++ ++ if (status > 0) { ++ more_to_do = 1; ++ } else if (status < 0) { ++ no_fifo_space = 1; ++ break; ++ } ++ } ++ /* Advance to next QH, skipping start-of-list entry. */ ++ hcd->non_periodic_qh_ptr = hcd->non_periodic_qh_ptr->next; ++ if (hcd->non_periodic_qh_ptr == &hcd->non_periodic_sched_active) { ++ hcd->non_periodic_qh_ptr = ++ hcd->non_periodic_qh_ptr->next; ++ } ++ ++ } while (hcd->non_periodic_qh_ptr != orig_qh_ptr); ++ ++ if (!hcd->core_if->dma_enable) { ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ intr_mask.b.nptxfempty = 1; ++ ++#ifdef DEBUG ++ tx_status.d32 = DWC_READ_REG32(&global_regs->gnptxsts); ++ DWC_DEBUGPL(DBG_HCDV, ++ " NP Tx Req Queue Space Avail (after queue): %d\n", ++ tx_status.b.nptxqspcavail); ++ DWC_DEBUGPL(DBG_HCDV, ++ " NP Tx FIFO Space Avail (after queue): %d\n", ++ tx_status.b.nptxfspcavail); ++#endif ++ if (more_to_do || no_queue_space || no_fifo_space) { ++ /* ++ * May need to queue more transactions as the request ++ * queue or Tx FIFO empties. Enable the non-periodic ++ * Tx FIFO empty interrupt. (Always use the half-empty ++ * level to ensure that new requests are loaded as ++ * soon as possible.) ++ */ ++ DWC_MODIFY_REG32(&global_regs->gintmsk, 0, ++ intr_mask.d32); ++ } else { ++ /* ++ * Disable the Tx FIFO empty interrupt since there are ++ * no more transactions that need to be queued right ++ * now. This function is called from interrupt ++ * handlers to queue more transactions as transfer ++ * states change. ++ */ ++ DWC_MODIFY_REG32(&global_regs->gintmsk, intr_mask.d32, ++ 0); ++ } ++ } ++} ++ ++/** ++ * This function processes the currently active host channels and queues ++ * transactions for these channels to the DWC_otg controller. It is called ++ * from HCD interrupt handler functions. ++ * ++ * @param hcd The HCD state structure. ++ * @param tr_type The type(s) of transactions to queue (non-periodic, ++ * periodic, or both). ++ */ ++void dwc_otg_hcd_queue_transactions(dwc_otg_hcd_t * hcd, ++ dwc_otg_transaction_type_e tr_type) ++{ ++#ifdef DEBUG_SOF ++ DWC_DEBUGPL(DBG_HCD, "Queue Transactions\n"); ++#endif ++ /* Process host channels associated with periodic transfers. */ ++ if ((tr_type == DWC_OTG_TRANSACTION_PERIODIC || ++ tr_type == DWC_OTG_TRANSACTION_ALL) && ++ !DWC_LIST_EMPTY(&hcd->periodic_sched_assigned)) { ++ ++ process_periodic_channels(hcd); ++ } ++ ++ /* Process host channels associated with non-periodic transfers. */ ++ if (tr_type == DWC_OTG_TRANSACTION_NON_PERIODIC || ++ tr_type == DWC_OTG_TRANSACTION_ALL) { ++ if (!DWC_LIST_EMPTY(&hcd->non_periodic_sched_active)) { ++ process_non_periodic_channels(hcd); ++ } else { ++ /* ++ * Ensure NP Tx FIFO empty interrupt is disabled when ++ * there are no non-periodic transfers to process. ++ */ ++ gintmsk_data_t gintmsk = {.d32 = 0 }; ++ gintmsk.b.nptxfempty = 1; ++ ++ if (fiq_enable) { ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&hcd->fiq_state->lock); ++ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, gintmsk.d32, 0); ++ fiq_fsm_spin_unlock(&hcd->fiq_state->lock); ++ local_fiq_enable(); ++ } else { ++ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, gintmsk.d32, 0); ++ } ++ } ++ } ++} ++ ++#ifdef DWC_HS_ELECT_TST ++/* ++ * Quick and dirty hack to implement the HS Electrical Test ++ * SINGLE_STEP_GET_DEVICE_DESCRIPTOR feature. ++ * ++ * This code was copied from our userspace app "hset". It sends a ++ * Get Device Descriptor control sequence in two parts, first the ++ * Setup packet by itself, followed some time later by the In and ++ * Ack packets. Rather than trying to figure out how to add this ++ * functionality to the normal driver code, we just hijack the ++ * hardware, using these two function to drive the hardware ++ * directly. ++ */ ++ ++static dwc_otg_core_global_regs_t *global_regs; ++static dwc_otg_host_global_regs_t *hc_global_regs; ++static dwc_otg_hc_regs_t *hc_regs; ++static uint32_t *data_fifo; ++ ++static void do_setup(void) ++{ ++ gintsts_data_t gintsts; ++ hctsiz_data_t hctsiz; ++ hcchar_data_t hcchar; ++ haint_data_t haint; ++ hcint_data_t hcint; ++ ++ /* Enable HAINTs */ ++ DWC_WRITE_REG32(&hc_global_regs->haintmsk, 0x0001); ++ ++ /* Enable HCINTs */ ++ DWC_WRITE_REG32(&hc_regs->hcintmsk, 0x04a3); ++ ++ /* Read GINTSTS */ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++ /* Read HAINT */ ++ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint); ++ ++ /* Read HCINT */ ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ ++ /* Read HCCHAR */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ ++ /* Clear HCINT */ ++ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32); ++ ++ /* Clear HAINT */ ++ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32); ++ ++ /* Clear GINTSTS */ ++ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32); ++ ++ /* Read GINTSTS */ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++ /* ++ * Send Setup packet (Get Device Descriptor) ++ */ ++ ++ /* Make sure channel is disabled */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ if (hcchar.b.chen) { ++ hcchar.b.chdis = 1; ++// hcchar.b.chen = 1; ++ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32); ++ //sleep(1); ++ dwc_mdelay(1000); ++ ++ /* Read GINTSTS */ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++ /* Read HAINT */ ++ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint); ++ ++ /* Read HCINT */ ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ ++ /* Read HCCHAR */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ ++ /* Clear HCINT */ ++ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32); ++ ++ /* Clear HAINT */ ++ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32); ++ ++ /* Clear GINTSTS */ ++ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32); ++ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ } ++ ++ /* Set HCTSIZ */ ++ hctsiz.d32 = 0; ++ hctsiz.b.xfersize = 8; ++ hctsiz.b.pktcnt = 1; ++ hctsiz.b.pid = DWC_OTG_HC_PID_SETUP; ++ DWC_WRITE_REG32(&hc_regs->hctsiz, hctsiz.d32); ++ ++ /* Set HCCHAR */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ hcchar.b.eptype = DWC_OTG_EP_TYPE_CONTROL; ++ hcchar.b.epdir = 0; ++ hcchar.b.epnum = 0; ++ hcchar.b.mps = 8; ++ hcchar.b.chen = 1; ++ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32); ++ ++ /* Fill FIFO with Setup data for Get Device Descriptor */ ++ data_fifo = (uint32_t *) ((char *)global_regs + 0x1000); ++ DWC_WRITE_REG32(data_fifo++, 0x01000680); ++ DWC_WRITE_REG32(data_fifo++, 0x00080000); ++ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++ /* Wait for host channel interrupt */ ++ do { ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ } while (gintsts.b.hcintr == 0); ++ ++ /* Disable HCINTs */ ++ DWC_WRITE_REG32(&hc_regs->hcintmsk, 0x0000); ++ ++ /* Disable HAINTs */ ++ DWC_WRITE_REG32(&hc_global_regs->haintmsk, 0x0000); ++ ++ /* Read HAINT */ ++ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint); ++ ++ /* Read HCINT */ ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ ++ /* Read HCCHAR */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ ++ /* Clear HCINT */ ++ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32); ++ ++ /* Clear HAINT */ ++ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32); ++ ++ /* Clear GINTSTS */ ++ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32); ++ ++ /* Read GINTSTS */ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++} ++ ++static void do_in_ack(void) ++{ ++ gintsts_data_t gintsts; ++ hctsiz_data_t hctsiz; ++ hcchar_data_t hcchar; ++ haint_data_t haint; ++ hcint_data_t hcint; ++ host_grxsts_data_t grxsts; ++ ++ /* Enable HAINTs */ ++ DWC_WRITE_REG32(&hc_global_regs->haintmsk, 0x0001); ++ ++ /* Enable HCINTs */ ++ DWC_WRITE_REG32(&hc_regs->hcintmsk, 0x04a3); ++ ++ /* Read GINTSTS */ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++ /* Read HAINT */ ++ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint); ++ ++ /* Read HCINT */ ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ ++ /* Read HCCHAR */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ ++ /* Clear HCINT */ ++ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32); ++ ++ /* Clear HAINT */ ++ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32); ++ ++ /* Clear GINTSTS */ ++ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32); ++ ++ /* Read GINTSTS */ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++ /* ++ * Receive Control In packet ++ */ ++ ++ /* Make sure channel is disabled */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ if (hcchar.b.chen) { ++ hcchar.b.chdis = 1; ++ hcchar.b.chen = 1; ++ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32); ++ //sleep(1); ++ dwc_mdelay(1000); ++ ++ /* Read GINTSTS */ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++ /* Read HAINT */ ++ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint); ++ ++ /* Read HCINT */ ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ ++ /* Read HCCHAR */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ ++ /* Clear HCINT */ ++ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32); ++ ++ /* Clear HAINT */ ++ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32); ++ ++ /* Clear GINTSTS */ ++ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32); ++ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ } ++ ++ /* Set HCTSIZ */ ++ hctsiz.d32 = 0; ++ hctsiz.b.xfersize = 8; ++ hctsiz.b.pktcnt = 1; ++ hctsiz.b.pid = DWC_OTG_HC_PID_DATA1; ++ DWC_WRITE_REG32(&hc_regs->hctsiz, hctsiz.d32); ++ ++ /* Set HCCHAR */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ hcchar.b.eptype = DWC_OTG_EP_TYPE_CONTROL; ++ hcchar.b.epdir = 1; ++ hcchar.b.epnum = 0; ++ hcchar.b.mps = 8; ++ hcchar.b.chen = 1; ++ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32); ++ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++ /* Wait for receive status queue interrupt */ ++ do { ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ } while (gintsts.b.rxstsqlvl == 0); ++ ++ /* Read RXSTS */ ++ grxsts.d32 = DWC_READ_REG32(&global_regs->grxstsp); ++ ++ /* Clear RXSTSQLVL in GINTSTS */ ++ gintsts.d32 = 0; ++ gintsts.b.rxstsqlvl = 1; ++ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32); ++ ++ switch (grxsts.b.pktsts) { ++ case DWC_GRXSTS_PKTSTS_IN: ++ /* Read the data into the host buffer */ ++ if (grxsts.b.bcnt > 0) { ++ int i; ++ int word_count = (grxsts.b.bcnt + 3) / 4; ++ ++ data_fifo = (uint32_t *) ((char *)global_regs + 0x1000); ++ ++ for (i = 0; i < word_count; i++) { ++ (void)DWC_READ_REG32(data_fifo++); ++ } ++ } ++ break; ++ ++ default: ++ break; ++ } ++ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++ /* Wait for receive status queue interrupt */ ++ do { ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ } while (gintsts.b.rxstsqlvl == 0); ++ ++ /* Read RXSTS */ ++ grxsts.d32 = DWC_READ_REG32(&global_regs->grxstsp); ++ ++ /* Clear RXSTSQLVL in GINTSTS */ ++ gintsts.d32 = 0; ++ gintsts.b.rxstsqlvl = 1; ++ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32); ++ ++ switch (grxsts.b.pktsts) { ++ case DWC_GRXSTS_PKTSTS_IN_XFER_COMP: ++ break; ++ ++ default: ++ break; ++ } ++ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++ /* Wait for host channel interrupt */ ++ do { ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ } while (gintsts.b.hcintr == 0); ++ ++ /* Read HAINT */ ++ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint); ++ ++ /* Read HCINT */ ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ ++ /* Read HCCHAR */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ ++ /* Clear HCINT */ ++ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32); ++ ++ /* Clear HAINT */ ++ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32); ++ ++ /* Clear GINTSTS */ ++ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32); ++ ++ /* Read GINTSTS */ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++// usleep(100000); ++// mdelay(100); ++ dwc_mdelay(1); ++ ++ /* ++ * Send handshake packet ++ */ ++ ++ /* Read HAINT */ ++ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint); ++ ++ /* Read HCINT */ ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ ++ /* Read HCCHAR */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ ++ /* Clear HCINT */ ++ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32); ++ ++ /* Clear HAINT */ ++ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32); ++ ++ /* Clear GINTSTS */ ++ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32); ++ ++ /* Read GINTSTS */ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++ /* Make sure channel is disabled */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ if (hcchar.b.chen) { ++ hcchar.b.chdis = 1; ++ hcchar.b.chen = 1; ++ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32); ++ //sleep(1); ++ dwc_mdelay(1000); ++ ++ /* Read GINTSTS */ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++ /* Read HAINT */ ++ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint); ++ ++ /* Read HCINT */ ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ ++ /* Read HCCHAR */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ ++ /* Clear HCINT */ ++ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32); ++ ++ /* Clear HAINT */ ++ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32); ++ ++ /* Clear GINTSTS */ ++ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32); ++ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ } ++ ++ /* Set HCTSIZ */ ++ hctsiz.d32 = 0; ++ hctsiz.b.xfersize = 0; ++ hctsiz.b.pktcnt = 1; ++ hctsiz.b.pid = DWC_OTG_HC_PID_DATA1; ++ DWC_WRITE_REG32(&hc_regs->hctsiz, hctsiz.d32); ++ ++ /* Set HCCHAR */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ hcchar.b.eptype = DWC_OTG_EP_TYPE_CONTROL; ++ hcchar.b.epdir = 0; ++ hcchar.b.epnum = 0; ++ hcchar.b.mps = 8; ++ hcchar.b.chen = 1; ++ DWC_WRITE_REG32(&hc_regs->hcchar, hcchar.d32); ++ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ ++ /* Wait for host channel interrupt */ ++ do { ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++ } while (gintsts.b.hcintr == 0); ++ ++ /* Disable HCINTs */ ++ DWC_WRITE_REG32(&hc_regs->hcintmsk, 0x0000); ++ ++ /* Disable HAINTs */ ++ DWC_WRITE_REG32(&hc_global_regs->haintmsk, 0x0000); ++ ++ /* Read HAINT */ ++ haint.d32 = DWC_READ_REG32(&hc_global_regs->haint); ++ ++ /* Read HCINT */ ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ ++ /* Read HCCHAR */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ ++ /* Clear HCINT */ ++ DWC_WRITE_REG32(&hc_regs->hcint, hcint.d32); ++ ++ /* Clear HAINT */ ++ DWC_WRITE_REG32(&hc_global_regs->haint, haint.d32); ++ ++ /* Clear GINTSTS */ ++ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32); ++ ++ /* Read GINTSTS */ ++ gintsts.d32 = DWC_READ_REG32(&global_regs->gintsts); ++} ++#endif ++ ++/** Handles hub class-specific requests. */ ++int dwc_otg_hcd_hub_control(dwc_otg_hcd_t * dwc_otg_hcd, ++ uint16_t typeReq, ++ uint16_t wValue, ++ uint16_t wIndex, uint8_t * buf, uint16_t wLength) ++{ ++ int retval = 0; ++ ++ dwc_otg_core_if_t *core_if = dwc_otg_hcd->core_if; ++ usb_hub_descriptor_t *hub_desc; ++ hprt0_data_t hprt0 = {.d32 = 0 }; ++ ++ uint32_t port_status; ++ ++ switch (typeReq) { ++ case UCR_CLEAR_HUB_FEATURE: ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "ClearHubFeature 0x%x\n", wValue); ++ switch (wValue) { ++ case UHF_C_HUB_LOCAL_POWER: ++ case UHF_C_HUB_OVER_CURRENT: ++ /* Nothing required here */ ++ break; ++ default: ++ retval = -DWC_E_INVALID; ++ DWC_ERROR("DWC OTG HCD - " ++ "ClearHubFeature request %xh unknown\n", ++ wValue); ++ } ++ break; ++ case UCR_CLEAR_PORT_FEATURE: ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ if (wValue != UHF_PORT_L1) ++#endif ++ if (!wIndex || wIndex > 1) ++ goto error; ++ ++ switch (wValue) { ++ case UHF_PORT_ENABLE: ++ DWC_DEBUGPL(DBG_ANY, "DWC OTG HCD HUB CONTROL - " ++ "ClearPortFeature USB_PORT_FEAT_ENABLE\n"); ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtena = 1; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ break; ++ case UHF_PORT_SUSPEND: ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "ClearPortFeature USB_PORT_FEAT_SUSPEND\n"); ++ ++ if (core_if->power_down == 2) { ++ dwc_otg_host_hibernation_restore(core_if, 0, 0); ++ } else { ++ DWC_WRITE_REG32(core_if->pcgcctl, 0); ++ dwc_mdelay(5); ++ ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtres = 1; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ hprt0.b.prtsusp = 0; ++ /* Clear Resume bit */ ++ dwc_mdelay(100); ++ hprt0.b.prtres = 0; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ } ++ break; ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ case UHF_PORT_L1: ++ { ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ glpmcfg_data_t lpmcfg = {.d32 = 0 }; ++ ++ lpmcfg.d32 = ++ DWC_READ_REG32(&core_if-> ++ core_global_regs->glpmcfg); ++ lpmcfg.b.en_utmi_sleep = 0; ++ lpmcfg.b.hird_thres &= (~(1 << 4)); ++ lpmcfg.b.prt_sleep_sts = 1; ++ DWC_WRITE_REG32(&core_if-> ++ core_global_regs->glpmcfg, ++ lpmcfg.d32); ++ ++ /* Clear Enbl_L1Gating bit. */ ++ pcgcctl.b.enbl_sleep_gating = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, ++ 0); ++ ++ dwc_mdelay(5); ++ ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtres = 1; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, ++ hprt0.d32); ++ /* This bit will be cleared in wakeup interrupt handle */ ++ break; ++ } ++#endif ++ case UHF_PORT_POWER: ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "ClearPortFeature USB_PORT_FEAT_POWER\n"); ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtpwr = 0; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ break; ++ case UHF_PORT_INDICATOR: ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "ClearPortFeature USB_PORT_FEAT_INDICATOR\n"); ++ /* Port inidicator not supported */ ++ break; ++ case UHF_C_PORT_CONNECTION: ++ /* Clears drivers internal connect status change ++ * flag */ ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "ClearPortFeature USB_PORT_FEAT_C_CONNECTION\n"); ++ dwc_otg_hcd->flags.b.port_connect_status_change = 0; ++ break; ++ case UHF_C_PORT_RESET: ++ /* Clears the driver's internal Port Reset Change ++ * flag */ ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "ClearPortFeature USB_PORT_FEAT_C_RESET\n"); ++ dwc_otg_hcd->flags.b.port_reset_change = 0; ++ break; ++ case UHF_C_PORT_ENABLE: ++ /* Clears the driver's internal Port ++ * Enable/Disable Change flag */ ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "ClearPortFeature USB_PORT_FEAT_C_ENABLE\n"); ++ dwc_otg_hcd->flags.b.port_enable_change = 0; ++ break; ++ case UHF_C_PORT_SUSPEND: ++ /* Clears the driver's internal Port Suspend ++ * Change flag, which is set when resume signaling on ++ * the host port is complete */ ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "ClearPortFeature USB_PORT_FEAT_C_SUSPEND\n"); ++ dwc_otg_hcd->flags.b.port_suspend_change = 0; ++ break; ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ case UHF_C_PORT_L1: ++ dwc_otg_hcd->flags.b.port_l1_change = 0; ++ break; ++#endif ++ case UHF_C_PORT_OVER_CURRENT: ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "ClearPortFeature USB_PORT_FEAT_C_OVER_CURRENT\n"); ++ dwc_otg_hcd->flags.b.port_over_current_change = 0; ++ break; ++ default: ++ retval = -DWC_E_INVALID; ++ DWC_ERROR("DWC OTG HCD - " ++ "ClearPortFeature request %xh " ++ "unknown or unsupported\n", wValue); ++ } ++ break; ++ case UCR_GET_HUB_DESCRIPTOR: ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "GetHubDescriptor\n"); ++ hub_desc = (usb_hub_descriptor_t *) buf; ++ hub_desc->bDescLength = 9; ++ hub_desc->bDescriptorType = 0x29; ++ hub_desc->bNbrPorts = 1; ++ USETW(hub_desc->wHubCharacteristics, 0x08); ++ hub_desc->bPwrOn2PwrGood = 1; ++ hub_desc->bHubContrCurrent = 0; ++ hub_desc->DeviceRemovable[0] = 0; ++ hub_desc->DeviceRemovable[1] = 0xff; ++ break; ++ case UCR_GET_HUB_STATUS: ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "GetHubStatus\n"); ++ DWC_MEMSET(buf, 0, 4); ++ break; ++ case UCR_GET_PORT_STATUS: ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "GetPortStatus wIndex = 0x%04x FLAGS=0x%08x\n", ++ wIndex, dwc_otg_hcd->flags.d32); ++ if (!wIndex || wIndex > 1) ++ goto error; ++ ++ port_status = 0; ++ ++ if (dwc_otg_hcd->flags.b.port_connect_status_change) ++ port_status |= (1 << UHF_C_PORT_CONNECTION); ++ ++ if (dwc_otg_hcd->flags.b.port_enable_change) ++ port_status |= (1 << UHF_C_PORT_ENABLE); ++ ++ if (dwc_otg_hcd->flags.b.port_suspend_change) ++ port_status |= (1 << UHF_C_PORT_SUSPEND); ++ ++ if (dwc_otg_hcd->flags.b.port_l1_change) ++ port_status |= (1 << UHF_C_PORT_L1); ++ ++ if (dwc_otg_hcd->flags.b.port_reset_change) { ++ port_status |= (1 << UHF_C_PORT_RESET); ++ } ++ ++ if (dwc_otg_hcd->flags.b.port_over_current_change) { ++ DWC_WARN("Overcurrent change detected\n"); ++ port_status |= (1 << UHF_C_PORT_OVER_CURRENT); ++ } ++ ++ if (!dwc_otg_hcd->flags.b.port_connect_status) { ++ /* ++ * The port is disconnected, which means the core is ++ * either in device mode or it soon will be. Just ++ * return 0's for the remainder of the port status ++ * since the port register can't be read if the core ++ * is in device mode. ++ */ ++ *((__le32 *) buf) = dwc_cpu_to_le32(&port_status); ++ break; ++ } ++ ++ hprt0.d32 = DWC_READ_REG32(core_if->host_if->hprt0); ++ DWC_DEBUGPL(DBG_HCDV, " HPRT0: 0x%08x\n", hprt0.d32); ++ ++ if (hprt0.b.prtconnsts) ++ port_status |= (1 << UHF_PORT_CONNECTION); ++ ++ if (hprt0.b.prtena) ++ port_status |= (1 << UHF_PORT_ENABLE); ++ ++ if (hprt0.b.prtsusp) ++ port_status |= (1 << UHF_PORT_SUSPEND); ++ ++ if (hprt0.b.prtovrcurract) ++ port_status |= (1 << UHF_PORT_OVER_CURRENT); ++ ++ if (hprt0.b.prtrst) ++ port_status |= (1 << UHF_PORT_RESET); ++ ++ if (hprt0.b.prtpwr) ++ port_status |= (1 << UHF_PORT_POWER); ++ ++ if (hprt0.b.prtspd == DWC_HPRT0_PRTSPD_HIGH_SPEED) ++ port_status |= (1 << UHF_PORT_HIGH_SPEED); ++ else if (hprt0.b.prtspd == DWC_HPRT0_PRTSPD_LOW_SPEED) ++ port_status |= (1 << UHF_PORT_LOW_SPEED); ++ ++ if (hprt0.b.prttstctl) ++ port_status |= (1 << UHF_PORT_TEST); ++ if (dwc_otg_get_lpm_portsleepstatus(dwc_otg_hcd->core_if)) { ++ port_status |= (1 << UHF_PORT_L1); ++ } ++ /* ++ For Synopsys HW emulation of Power down wkup_control asserts the ++ hreset_n and prst_n on suspned. This causes the HPRT0 to be zero. ++ We intentionally tell the software that port is in L2Suspend state. ++ Only for STE. ++ */ ++ if ((core_if->power_down == 2) ++ && (core_if->hibernation_suspend == 1)) { ++ port_status |= (1 << UHF_PORT_SUSPEND); ++ } ++ /* USB_PORT_FEAT_INDICATOR unsupported always 0 */ ++ ++ *((__le32 *) buf) = dwc_cpu_to_le32(&port_status); ++ ++ break; ++ case UCR_SET_HUB_FEATURE: ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "SetHubFeature\n"); ++ /* No HUB features supported */ ++ break; ++ case UCR_SET_PORT_FEATURE: ++ if (wValue != UHF_PORT_TEST && (!wIndex || wIndex > 1)) ++ goto error; ++ ++ if (!dwc_otg_hcd->flags.b.port_connect_status) { ++ /* ++ * The port is disconnected, which means the core is ++ * either in device mode or it soon will be. Just ++ * return without doing anything since the port ++ * register can't be written if the core is in device ++ * mode. ++ */ ++ break; ++ } ++ ++ switch (wValue) { ++ case UHF_PORT_SUSPEND: ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "SetPortFeature - USB_PORT_FEAT_SUSPEND\n"); ++ if (dwc_otg_hcd_otg_port(dwc_otg_hcd) != wIndex) { ++ goto error; ++ } ++ if (core_if->power_down == 2) { ++ int timeout = 300; ++ dwc_irqflags_t flags; ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ gusbcfg_data_t gusbcfg = {.d32 = 0 }; ++#ifdef DWC_DEV_SRPCAP ++ int32_t otg_cap_param = core_if->core_params->otg_cap; ++#endif ++ DWC_PRINTF("Preparing for complete power-off\n"); ++ ++ /* Save registers before hibernation */ ++ dwc_otg_save_global_regs(core_if); ++ dwc_otg_save_host_regs(core_if); ++ ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtsusp = 1; ++ hprt0.b.prtena = 0; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ /* Spin hprt0.b.prtsusp to became 1 */ ++ do { ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ if (hprt0.b.prtsusp) { ++ break; ++ } ++ dwc_mdelay(1); ++ } while (--timeout); ++ if (!timeout) { ++ DWC_WARN("Suspend wasn't genereted\n"); ++ } ++ dwc_udelay(10); ++ ++ /* ++ * We need to disable interrupts to prevent servicing of any IRQ ++ * during going to hibernation ++ */ ++ DWC_SPINLOCK_IRQSAVE(dwc_otg_hcd->lock, &flags); ++ core_if->lx_state = DWC_OTG_L2; ++#ifdef DWC_DEV_SRPCAP ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtpwr = 0; ++ hprt0.b.prtena = 0; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, ++ hprt0.d32); ++#endif ++ gusbcfg.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs-> ++ gusbcfg); ++ if (gusbcfg.b.ulpi_utmi_sel == 1) { ++ /* ULPI interface */ ++ /* Suspend the Phy Clock */ ++ pcgcctl.d32 = 0; ++ pcgcctl.b.stoppclk = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, 0, ++ pcgcctl.d32); ++ dwc_udelay(10); ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if-> ++ core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ } else { ++ /* UTMI+ Interface */ ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if-> ++ core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ pcgcctl.b.stoppclk = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, 0, pcgcctl.d32); ++ dwc_udelay(10); ++ } ++#ifdef DWC_DEV_SRPCAP ++ gpwrdn.d32 = 0; ++ gpwrdn.b.dis_vbus = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++#endif ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ gpwrdn.d32 = 0; ++#ifdef DWC_DEV_SRPCAP ++ gpwrdn.b.srp_det_msk = 1; ++#endif ++ gpwrdn.b.disconn_det_msk = 1; ++ gpwrdn.b.lnstchng_msk = 1; ++ gpwrdn.b.sts_chngint_msk = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Enable Power Down Clamp and all interrupts in GPWRDN */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnclmp = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ dwc_udelay(10); ++ ++ /* Switch off VDD */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ ++#ifdef DWC_DEV_SRPCAP ++ if (otg_cap_param == DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE) ++ { ++ core_if->pwron_timer_started = 1; ++ DWC_TIMER_SCHEDULE(core_if->pwron_timer, 6000 /* 6 secs */ ); ++ } ++#endif ++ /* Save gpwrdn register for further usage if stschng interrupt */ ++ core_if->gr_backup->gpwrdn_local = ++ DWC_READ_REG32(&core_if->core_global_regs->gpwrdn); ++ ++ /* Set flag to indicate that we are in hibernation */ ++ core_if->hibernation_suspend = 1; ++ DWC_SPINUNLOCK_IRQRESTORE(dwc_otg_hcd->lock,flags); ++ ++ DWC_PRINTF("Host hibernation completed\n"); ++ // Exit from case statement ++ break; ++ ++ } ++ if (dwc_otg_hcd_otg_port(dwc_otg_hcd) == wIndex && ++ dwc_otg_hcd->fops->get_b_hnp_enable(dwc_otg_hcd)) { ++ gotgctl_data_t gotgctl = {.d32 = 0 }; ++ gotgctl.b.hstsethnpen = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gotgctl, 0, gotgctl.d32); ++ core_if->op_state = A_SUSPEND; ++ } ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtsusp = 1; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ { ++ dwc_irqflags_t flags; ++ /* Update lx_state */ ++ DWC_SPINLOCK_IRQSAVE(dwc_otg_hcd->lock, &flags); ++ core_if->lx_state = DWC_OTG_L2; ++ DWC_SPINUNLOCK_IRQRESTORE(dwc_otg_hcd->lock, flags); ++ } ++ /* Suspend the Phy Clock */ ++ { ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ pcgcctl.b.stoppclk = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, 0, ++ pcgcctl.d32); ++ dwc_udelay(10); ++ } ++ ++ /* For HNP the bus must be suspended for at least 200ms. */ ++ if (dwc_otg_hcd->fops->get_b_hnp_enable(dwc_otg_hcd)) { ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ pcgcctl.b.stoppclk = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0); ++ dwc_mdelay(200); ++ } ++ ++ /** @todo - check how sw can wait for 1 sec to check asesvld??? */ ++#if 0 //vahrama !!!!!!!!!!!!!!!!!! ++ if (core_if->adp_enable) { ++ gotgctl_data_t gotgctl = {.d32 = 0 }; ++ gpwrdn_data_t gpwrdn; ++ ++ while (gotgctl.b.asesvld == 1) { ++ gotgctl.d32 = ++ DWC_READ_REG32(&core_if-> ++ core_global_regs-> ++ gotgctl); ++ dwc_mdelay(100); ++ } ++ ++ /* Enable Power Down Logic */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ ++ /* Unmask SRP detected interrupt from Power Down Logic */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.srp_det_msk = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs-> ++ gpwrdn, 0, gpwrdn.d32); ++ ++ dwc_otg_adp_probe_start(core_if); ++ } ++#endif ++ break; ++ case UHF_PORT_POWER: ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "SetPortFeature - USB_PORT_FEAT_POWER\n"); ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtpwr = 1; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ break; ++ case UHF_PORT_RESET: ++ if ((core_if->power_down == 2) ++ && (core_if->hibernation_suspend == 1)) { ++ /* If we are going to exit from Hibernated ++ * state via USB RESET. ++ */ ++ dwc_otg_host_hibernation_restore(core_if, 0, 1); ++ } else { ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ ++ DWC_DEBUGPL(DBG_HCD, ++ "DWC OTG HCD HUB CONTROL - " ++ "SetPortFeature - USB_PORT_FEAT_RESET\n"); ++ { ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ pcgcctl.b.enbl_sleep_gating = 1; ++ pcgcctl.b.stoppclk = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, pcgcctl.d32, 0); ++ DWC_WRITE_REG32(core_if->pcgcctl, 0); ++ } ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ { ++ glpmcfg_data_t lpmcfg; ++ lpmcfg.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ if (lpmcfg.b.prt_sleep_sts) { ++ lpmcfg.b.en_utmi_sleep = 0; ++ lpmcfg.b.hird_thres &= (~(1 << 4)); ++ DWC_WRITE_REG32 ++ (&core_if->core_global_regs->glpmcfg, ++ lpmcfg.d32); ++ dwc_mdelay(1); ++ } ++ } ++#endif ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ /* Clear suspend bit if resetting from suspended state. */ ++ hprt0.b.prtsusp = 0; ++ /* When B-Host the Port reset bit is set in ++ * the Start HCD Callback function, so that ++ * the reset is started within 1ms of the HNP ++ * success interrupt. */ ++ if (!dwc_otg_hcd_is_b_host(dwc_otg_hcd)) { ++ hprt0.b.prtpwr = 1; ++ hprt0.b.prtrst = 1; ++ DWC_PRINTF("Indeed it is in host mode hprt0 = %08x\n",hprt0.d32); ++ DWC_WRITE_REG32(core_if->host_if->hprt0, ++ hprt0.d32); ++ } ++ /* Clear reset bit in 10ms (FS/LS) or 50ms (HS) */ ++ dwc_mdelay(60); ++ hprt0.b.prtrst = 0; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ core_if->lx_state = DWC_OTG_L0; /* Now back to the on state */ ++ } ++ break; ++#ifdef DWC_HS_ELECT_TST ++ case UHF_PORT_TEST: ++ { ++ uint32_t t; ++ gintmsk_data_t gintmsk; ++ ++ t = (wIndex >> 8); /* MSB wIndex USB */ ++ DWC_DEBUGPL(DBG_HCD, ++ "DWC OTG HCD HUB CONTROL - " ++ "SetPortFeature - USB_PORT_FEAT_TEST %d\n", ++ t); ++ DWC_WARN("USB_PORT_FEAT_TEST %d\n", t); ++ if (t < 6) { ++ hprt0.d32 = dwc_otg_read_hprt0(core_if); ++ hprt0.b.prttstctl = t; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, ++ hprt0.d32); ++ } else { ++ /* Setup global vars with reg addresses (quick and ++ * dirty hack, should be cleaned up) ++ */ ++ global_regs = core_if->core_global_regs; ++ hc_global_regs = ++ core_if->host_if->host_global_regs; ++ hc_regs = ++ (dwc_otg_hc_regs_t *) ((char *) ++ global_regs + ++ 0x500); ++ data_fifo = ++ (uint32_t *) ((char *)global_regs + ++ 0x1000); ++ ++ if (t == 6) { /* HS_HOST_PORT_SUSPEND_RESUME */ ++ /* Save current interrupt mask */ ++ gintmsk.d32 = ++ DWC_READ_REG32 ++ (&global_regs->gintmsk); ++ ++ /* Disable all interrupts while we muck with ++ * the hardware directly ++ */ ++ DWC_WRITE_REG32(&global_regs->gintmsk, 0); ++ ++ /* 15 second delay per the test spec */ ++ dwc_mdelay(15000); ++ ++ /* Drive suspend on the root port */ ++ hprt0.d32 = ++ dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtsusp = 1; ++ hprt0.b.prtres = 0; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ ++ /* 15 second delay per the test spec */ ++ dwc_mdelay(15000); ++ ++ /* Drive resume on the root port */ ++ hprt0.d32 = ++ dwc_otg_read_hprt0(core_if); ++ hprt0.b.prtsusp = 0; ++ hprt0.b.prtres = 1; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ dwc_mdelay(100); ++ ++ /* Clear the resume bit */ ++ hprt0.b.prtres = 0; ++ DWC_WRITE_REG32(core_if->host_if->hprt0, hprt0.d32); ++ ++ /* Restore interrupts */ ++ DWC_WRITE_REG32(&global_regs->gintmsk, gintmsk.d32); ++ } else if (t == 7) { /* SINGLE_STEP_GET_DEVICE_DESCRIPTOR setup */ ++ /* Save current interrupt mask */ ++ gintmsk.d32 = ++ DWC_READ_REG32 ++ (&global_regs->gintmsk); ++ ++ /* Disable all interrupts while we muck with ++ * the hardware directly ++ */ ++ DWC_WRITE_REG32(&global_regs->gintmsk, 0); ++ ++ /* 15 second delay per the test spec */ ++ dwc_mdelay(15000); ++ ++ /* Send the Setup packet */ ++ do_setup(); ++ ++ /* 15 second delay so nothing else happens for awhile */ ++ dwc_mdelay(15000); ++ ++ /* Restore interrupts */ ++ DWC_WRITE_REG32(&global_regs->gintmsk, gintmsk.d32); ++ } else if (t == 8) { /* SINGLE_STEP_GET_DEVICE_DESCRIPTOR execute */ ++ /* Save current interrupt mask */ ++ gintmsk.d32 = ++ DWC_READ_REG32 ++ (&global_regs->gintmsk); ++ ++ /* Disable all interrupts while we muck with ++ * the hardware directly ++ */ ++ DWC_WRITE_REG32(&global_regs->gintmsk, 0); ++ ++ /* Send the Setup packet */ ++ do_setup(); ++ ++ /* 15 second delay so nothing else happens for awhile */ ++ dwc_mdelay(15000); ++ ++ /* Send the In and Ack packets */ ++ do_in_ack(); ++ ++ /* 15 second delay so nothing else happens for awhile */ ++ dwc_mdelay(15000); ++ ++ /* Restore interrupts */ ++ DWC_WRITE_REG32(&global_regs->gintmsk, gintmsk.d32); ++ } ++ } ++ break; ++ } ++#endif /* DWC_HS_ELECT_TST */ ++ ++ case UHF_PORT_INDICATOR: ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB CONTROL - " ++ "SetPortFeature - USB_PORT_FEAT_INDICATOR\n"); ++ /* Not supported */ ++ break; ++ default: ++ retval = -DWC_E_INVALID; ++ DWC_ERROR("DWC OTG HCD - " ++ "SetPortFeature request %xh " ++ "unknown or unsupported\n", wValue); ++ break; ++ } ++ break; ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ case UCR_SET_AND_TEST_PORT_FEATURE: ++ if (wValue != UHF_PORT_L1) { ++ goto error; ++ } ++ { ++ int portnum, hird, devaddr, remwake; ++ glpmcfg_data_t lpmcfg; ++ uint32_t time_usecs; ++ gintsts_data_t gintsts; ++ gintmsk_data_t gintmsk; ++ ++ if (!dwc_otg_get_param_lpm_enable(core_if)) { ++ goto error; ++ } ++ if (wValue != UHF_PORT_L1 || wLength != 1) { ++ goto error; ++ } ++ /* Check if the port currently is in SLEEP state */ ++ lpmcfg.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ if (lpmcfg.b.prt_sleep_sts) { ++ DWC_INFO("Port is already in sleep mode\n"); ++ buf[0] = 0; /* Return success */ ++ break; ++ } ++ ++ portnum = wIndex & 0xf; ++ hird = (wIndex >> 4) & 0xf; ++ devaddr = (wIndex >> 8) & 0x7f; ++ remwake = (wIndex >> 15); ++ ++ if (portnum != 1) { ++ retval = -DWC_E_INVALID; ++ DWC_WARN ++ ("Wrong port number(%d) in SetandTestPortFeature request\n", ++ portnum); ++ break; ++ } ++ ++ DWC_PRINTF ++ ("SetandTestPortFeature request: portnum = %d, hird = %d, devaddr = %d, rewake = %d\n", ++ portnum, hird, devaddr, remwake); ++ /* Disable LPM interrupt */ ++ gintmsk.d32 = 0; ++ gintmsk.b.lpmtranrcvd = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, ++ gintmsk.d32, 0); ++ ++ if (dwc_otg_hcd_send_lpm ++ (dwc_otg_hcd, devaddr, hird, remwake)) { ++ retval = -DWC_E_INVALID; ++ break; ++ } ++ ++ time_usecs = 10 * (lpmcfg.b.retry_count + 1); ++ /* We will consider timeout if time_usecs microseconds pass, ++ * and we don't receive LPM transaction status. ++ * After receiving non-error responce(ACK/NYET/STALL) from device, ++ * core will set lpmtranrcvd bit. ++ */ ++ do { ++ gintsts.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->gintsts); ++ if (gintsts.b.lpmtranrcvd) { ++ break; ++ } ++ dwc_udelay(1); ++ } while (--time_usecs); ++ /* lpm_int bit will be cleared in LPM interrupt handler */ ++ ++ /* Now fill status ++ * 0x00 - Success ++ * 0x10 - NYET ++ * 0x11 - Timeout ++ */ ++ if (!gintsts.b.lpmtranrcvd) { ++ buf[0] = 0x3; /* Completion code is Timeout */ ++ dwc_otg_hcd_free_hc_from_lpm(dwc_otg_hcd); ++ } else { ++ lpmcfg.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ if (lpmcfg.b.lpm_resp == 0x3) { ++ /* ACK responce from the device */ ++ buf[0] = 0x00; /* Success */ ++ } else if (lpmcfg.b.lpm_resp == 0x2) { ++ /* NYET responce from the device */ ++ buf[0] = 0x2; ++ } else { ++ /* Otherwise responce with Timeout */ ++ buf[0] = 0x3; ++ } ++ } ++ DWC_PRINTF("Device responce to LPM trans is %x\n", ++ lpmcfg.b.lpm_resp); ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, 0, ++ gintmsk.d32); ++ ++ break; ++ } ++#endif /* CONFIG_USB_DWC_OTG_LPM */ ++ default: ++error: ++ retval = -DWC_E_INVALID; ++ DWC_WARN("DWC OTG HCD - " ++ "Unknown hub control request type or invalid typeReq: %xh wIndex: %xh wValue: %xh\n", ++ typeReq, wIndex, wValue); ++ break; ++ } ++ ++ return retval; ++} ++ ++#ifdef CONFIG_USB_DWC_OTG_LPM ++/** Returns index of host channel to perform LPM transaction. */ ++int dwc_otg_hcd_get_hc_for_lpm_tran(dwc_otg_hcd_t * hcd, uint8_t devaddr) ++{ ++ dwc_otg_core_if_t *core_if = hcd->core_if; ++ dwc_hc_t *hc; ++ hcchar_data_t hcchar; ++ gintmsk_data_t gintmsk = {.d32 = 0 }; ++ ++ if (DWC_CIRCLEQ_EMPTY(&hcd->free_hc_list)) { ++ DWC_PRINTF("No free channel to select for LPM transaction\n"); ++ return -1; ++ } ++ ++ hc = DWC_CIRCLEQ_FIRST(&hcd->free_hc_list); ++ ++ /* Mask host channel interrupts. */ ++ gintmsk.b.hcintr = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, gintmsk.d32, 0); ++ ++ /* Fill fields that core needs for LPM transaction */ ++ hcchar.b.devaddr = devaddr; ++ hcchar.b.epnum = 0; ++ hcchar.b.eptype = DWC_OTG_EP_TYPE_CONTROL; ++ hcchar.b.mps = 64; ++ hcchar.b.lspddev = (hc->speed == DWC_OTG_EP_SPEED_LOW); ++ hcchar.b.epdir = 0; /* OUT */ ++ DWC_WRITE_REG32(&core_if->host_if->hc_regs[hc->hc_num]->hcchar, ++ hcchar.d32); ++ ++ /* Remove the host channel from the free list. */ ++ DWC_CIRCLEQ_REMOVE_INIT(&hcd->free_hc_list, hc, hc_list_entry); ++ ++ DWC_PRINTF("hcnum = %d devaddr = %d\n", hc->hc_num, devaddr); ++ ++ return hc->hc_num; ++} ++ ++/** Release hc after performing LPM transaction */ ++void dwc_otg_hcd_free_hc_from_lpm(dwc_otg_hcd_t * hcd) ++{ ++ dwc_hc_t *hc; ++ glpmcfg_data_t lpmcfg; ++ uint8_t hc_num; ++ ++ lpmcfg.d32 = DWC_READ_REG32(&hcd->core_if->core_global_regs->glpmcfg); ++ hc_num = lpmcfg.b.lpm_chan_index; ++ ++ hc = hcd->hc_ptr_array[hc_num]; ++ ++ DWC_PRINTF("Freeing channel %d after LPM\n", hc_num); ++ /* Return host channel to free list */ ++ DWC_CIRCLEQ_INSERT_TAIL(&hcd->free_hc_list, hc, hc_list_entry); ++} ++ ++int dwc_otg_hcd_send_lpm(dwc_otg_hcd_t * hcd, uint8_t devaddr, uint8_t hird, ++ uint8_t bRemoteWake) ++{ ++ glpmcfg_data_t lpmcfg; ++ pcgcctl_data_t pcgcctl = {.d32 = 0 }; ++ int channel; ++ ++ channel = dwc_otg_hcd_get_hc_for_lpm_tran(hcd, devaddr); ++ if (channel < 0) { ++ return channel; ++ } ++ ++ pcgcctl.b.enbl_sleep_gating = 1; ++ DWC_MODIFY_REG32(hcd->core_if->pcgcctl, 0, pcgcctl.d32); ++ ++ /* Read LPM config register */ ++ lpmcfg.d32 = DWC_READ_REG32(&hcd->core_if->core_global_regs->glpmcfg); ++ ++ /* Program LPM transaction fields */ ++ lpmcfg.b.rem_wkup_en = bRemoteWake; ++ lpmcfg.b.hird = hird; ++ lpmcfg.b.hird_thres = 0x1c; ++ lpmcfg.b.lpm_chan_index = channel; ++ lpmcfg.b.en_utmi_sleep = 1; ++ /* Program LPM config register */ ++ DWC_WRITE_REG32(&hcd->core_if->core_global_regs->glpmcfg, lpmcfg.d32); ++ ++ /* Send LPM transaction */ ++ lpmcfg.b.send_lpm = 1; ++ DWC_WRITE_REG32(&hcd->core_if->core_global_regs->glpmcfg, lpmcfg.d32); ++ ++ return 0; ++} ++ ++#endif /* CONFIG_USB_DWC_OTG_LPM */ ++ ++int dwc_otg_hcd_is_status_changed(dwc_otg_hcd_t * hcd, int port) ++{ ++ int retval; ++ ++ if (port != 1) { ++ return -DWC_E_INVALID; ++ } ++ ++ retval = (hcd->flags.b.port_connect_status_change || ++ hcd->flags.b.port_reset_change || ++ hcd->flags.b.port_enable_change || ++ hcd->flags.b.port_suspend_change || ++ hcd->flags.b.port_over_current_change); ++#ifdef DEBUG ++ if (retval) { ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD HUB STATUS DATA:" ++ " Root port status changed\n"); ++ DWC_DEBUGPL(DBG_HCDV, " port_connect_status_change: %d\n", ++ hcd->flags.b.port_connect_status_change); ++ DWC_DEBUGPL(DBG_HCDV, " port_reset_change: %d\n", ++ hcd->flags.b.port_reset_change); ++ DWC_DEBUGPL(DBG_HCDV, " port_enable_change: %d\n", ++ hcd->flags.b.port_enable_change); ++ DWC_DEBUGPL(DBG_HCDV, " port_suspend_change: %d\n", ++ hcd->flags.b.port_suspend_change); ++ DWC_DEBUGPL(DBG_HCDV, " port_over_current_change: %d\n", ++ hcd->flags.b.port_over_current_change); ++ } ++#endif ++ return retval; ++} ++ ++int dwc_otg_hcd_get_frame_number(dwc_otg_hcd_t * dwc_otg_hcd) ++{ ++ hfnum_data_t hfnum; ++ hfnum.d32 = ++ DWC_READ_REG32(&dwc_otg_hcd->core_if->host_if->host_global_regs-> ++ hfnum); ++ ++#ifdef DEBUG_SOF ++ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD GET FRAME NUMBER %d\n", ++ hfnum.b.frnum); ++#endif ++ return hfnum.b.frnum; ++} ++ ++int dwc_otg_hcd_start(dwc_otg_hcd_t * hcd, ++ struct dwc_otg_hcd_function_ops *fops) ++{ ++ int retval = 0; ++ ++ hcd->fops = fops; ++ if (!dwc_otg_is_device_mode(hcd->core_if) && ++ (!hcd->core_if->adp_enable || hcd->core_if->adp.adp_started)) { ++ dwc_otg_hcd_reinit(hcd); ++ } else { ++ retval = -DWC_E_NO_DEVICE; ++ } ++ ++ return retval; ++} ++ ++void *dwc_otg_hcd_get_priv_data(dwc_otg_hcd_t * hcd) ++{ ++ return hcd->priv; ++} ++ ++void dwc_otg_hcd_set_priv_data(dwc_otg_hcd_t * hcd, void *priv_data) ++{ ++ hcd->priv = priv_data; ++} ++ ++uint32_t dwc_otg_hcd_otg_port(dwc_otg_hcd_t * hcd) ++{ ++ return hcd->otg_port; ++} ++ ++uint32_t dwc_otg_hcd_is_b_host(dwc_otg_hcd_t * hcd) ++{ ++ uint32_t is_b_host; ++ if (hcd->core_if->op_state == B_HOST) { ++ is_b_host = 1; ++ } else { ++ is_b_host = 0; ++ } ++ ++ return is_b_host; ++} ++ ++dwc_otg_hcd_urb_t *dwc_otg_hcd_urb_alloc(dwc_otg_hcd_t * hcd, ++ int iso_desc_count, int atomic_alloc) ++{ ++ dwc_otg_hcd_urb_t *dwc_otg_urb; ++ uint32_t size; ++ ++ size = ++ sizeof(*dwc_otg_urb) + ++ iso_desc_count * sizeof(struct dwc_otg_hcd_iso_packet_desc); ++ if (atomic_alloc) ++ dwc_otg_urb = DWC_ALLOC_ATOMIC(size); ++ else ++ dwc_otg_urb = DWC_ALLOC(size); ++ ++ if (dwc_otg_urb) ++ dwc_otg_urb->packet_count = iso_desc_count; ++ else { ++ DWC_ERROR("**** DWC OTG HCD URB alloc - " ++ "%salloc of %db failed\n", ++ atomic_alloc?"atomic ":"", size); ++ } ++ return dwc_otg_urb; ++} ++ ++void dwc_otg_hcd_urb_set_pipeinfo(dwc_otg_hcd_urb_t * dwc_otg_urb, ++ uint8_t dev_addr, uint8_t ep_num, ++ uint8_t ep_type, uint8_t ep_dir, uint16_t mps) ++{ ++ dwc_otg_hcd_fill_pipe(&dwc_otg_urb->pipe_info, dev_addr, ep_num, ++ ep_type, ep_dir, mps); ++#if 0 ++ DWC_PRINTF ++ ("addr = %d, ep_num = %d, ep_dir = 0x%x, ep_type = 0x%x, mps = %d\n", ++ dev_addr, ep_num, ep_dir, ep_type, mps); ++#endif ++} ++ ++void dwc_otg_hcd_urb_set_params(dwc_otg_hcd_urb_t * dwc_otg_urb, ++ void *urb_handle, void *buf, dwc_dma_t dma, ++ uint32_t buflen, void *setup_packet, ++ dwc_dma_t setup_dma, uint32_t flags, ++ uint16_t interval) ++{ ++ dwc_otg_urb->priv = urb_handle; ++ dwc_otg_urb->buf = buf; ++ dwc_otg_urb->dma = dma; ++ dwc_otg_urb->length = buflen; ++ dwc_otg_urb->setup_packet = setup_packet; ++ dwc_otg_urb->setup_dma = setup_dma; ++ dwc_otg_urb->flags = flags; ++ dwc_otg_urb->interval = interval; ++ dwc_otg_urb->status = -DWC_E_IN_PROGRESS; ++} ++ ++uint32_t dwc_otg_hcd_urb_get_status(dwc_otg_hcd_urb_t * dwc_otg_urb) ++{ ++ return dwc_otg_urb->status; ++} ++ ++uint32_t dwc_otg_hcd_urb_get_actual_length(dwc_otg_hcd_urb_t * dwc_otg_urb) ++{ ++ return dwc_otg_urb->actual_length; ++} ++ ++uint32_t dwc_otg_hcd_urb_get_error_count(dwc_otg_hcd_urb_t * dwc_otg_urb) ++{ ++ return dwc_otg_urb->error_count; ++} ++ ++void dwc_otg_hcd_urb_set_iso_desc_params(dwc_otg_hcd_urb_t * dwc_otg_urb, ++ int desc_num, uint32_t offset, ++ uint32_t length) ++{ ++ dwc_otg_urb->iso_descs[desc_num].offset = offset; ++ dwc_otg_urb->iso_descs[desc_num].length = length; ++} ++ ++uint32_t dwc_otg_hcd_urb_get_iso_desc_status(dwc_otg_hcd_urb_t * dwc_otg_urb, ++ int desc_num) ++{ ++ return dwc_otg_urb->iso_descs[desc_num].status; ++} ++ ++uint32_t dwc_otg_hcd_urb_get_iso_desc_actual_length(dwc_otg_hcd_urb_t * ++ dwc_otg_urb, int desc_num) ++{ ++ return dwc_otg_urb->iso_descs[desc_num].actual_length; ++} ++ ++int dwc_otg_hcd_is_bandwidth_allocated(dwc_otg_hcd_t * hcd, void *ep_handle) ++{ ++ int allocated = 0; ++ dwc_otg_qh_t *qh = (dwc_otg_qh_t *) ep_handle; ++ ++ if (qh) { ++ if (!DWC_LIST_EMPTY(&qh->qh_list_entry)) { ++ allocated = 1; ++ } ++ } ++ return allocated; ++} ++ ++int dwc_otg_hcd_is_bandwidth_freed(dwc_otg_hcd_t * hcd, void *ep_handle) ++{ ++ dwc_otg_qh_t *qh = (dwc_otg_qh_t *) ep_handle; ++ int freed = 0; ++ DWC_ASSERT(qh, "qh is not allocated\n"); ++ ++ if (DWC_LIST_EMPTY(&qh->qh_list_entry)) { ++ freed = 1; ++ } ++ ++ return freed; ++} ++ ++uint8_t dwc_otg_hcd_get_ep_bandwidth(dwc_otg_hcd_t * hcd, void *ep_handle) ++{ ++ dwc_otg_qh_t *qh = (dwc_otg_qh_t *) ep_handle; ++ DWC_ASSERT(qh, "qh is not allocated\n"); ++ return qh->usecs; ++} ++ ++void dwc_otg_hcd_dump_state(dwc_otg_hcd_t * hcd) ++{ ++#ifdef DEBUG ++ int num_channels; ++ int i; ++ gnptxsts_data_t np_tx_status; ++ hptxsts_data_t p_tx_status; ++ ++ num_channels = hcd->core_if->core_params->host_channels; ++ DWC_PRINTF("\n"); ++ DWC_PRINTF ++ ("************************************************************\n"); ++ DWC_PRINTF("HCD State:\n"); ++ DWC_PRINTF(" Num channels: %d\n", num_channels); ++ for (i = 0; i < num_channels; i++) { ++ dwc_hc_t *hc = hcd->hc_ptr_array[i]; ++ DWC_PRINTF(" Channel %d:\n", i); ++ DWC_PRINTF(" dev_addr: %d, ep_num: %d, ep_is_in: %d\n", ++ hc->dev_addr, hc->ep_num, hc->ep_is_in); ++ DWC_PRINTF(" speed: %d\n", hc->speed); ++ DWC_PRINTF(" ep_type: %d\n", hc->ep_type); ++ DWC_PRINTF(" max_packet: %d\n", hc->max_packet); ++ DWC_PRINTF(" data_pid_start: %d\n", hc->data_pid_start); ++ DWC_PRINTF(" multi_count: %d\n", hc->multi_count); ++ DWC_PRINTF(" xfer_started: %d\n", hc->xfer_started); ++ DWC_PRINTF(" xfer_buff: %p\n", hc->xfer_buff); ++ DWC_PRINTF(" xfer_len: %d\n", hc->xfer_len); ++ DWC_PRINTF(" xfer_count: %d\n", hc->xfer_count); ++ DWC_PRINTF(" halt_on_queue: %d\n", hc->halt_on_queue); ++ DWC_PRINTF(" halt_pending: %d\n", hc->halt_pending); ++ DWC_PRINTF(" halt_status: %d\n", hc->halt_status); ++ DWC_PRINTF(" do_split: %d\n", hc->do_split); ++ DWC_PRINTF(" complete_split: %d\n", hc->complete_split); ++ DWC_PRINTF(" hub_addr: %d\n", hc->hub_addr); ++ DWC_PRINTF(" port_addr: %d\n", hc->port_addr); ++ DWC_PRINTF(" xact_pos: %d\n", hc->xact_pos); ++ DWC_PRINTF(" requests: %d\n", hc->requests); ++ DWC_PRINTF(" qh: %p\n", hc->qh); ++ if (hc->xfer_started) { ++ hfnum_data_t hfnum; ++ hcchar_data_t hcchar; ++ hctsiz_data_t hctsiz; ++ hcint_data_t hcint; ++ hcintmsk_data_t hcintmsk; ++ hfnum.d32 = ++ DWC_READ_REG32(&hcd->core_if-> ++ host_if->host_global_regs->hfnum); ++ hcchar.d32 = ++ DWC_READ_REG32(&hcd->core_if->host_if-> ++ hc_regs[i]->hcchar); ++ hctsiz.d32 = ++ DWC_READ_REG32(&hcd->core_if->host_if-> ++ hc_regs[i]->hctsiz); ++ hcint.d32 = ++ DWC_READ_REG32(&hcd->core_if->host_if-> ++ hc_regs[i]->hcint); ++ hcintmsk.d32 = ++ DWC_READ_REG32(&hcd->core_if->host_if-> ++ hc_regs[i]->hcintmsk); ++ DWC_PRINTF(" hfnum: 0x%08x\n", hfnum.d32); ++ DWC_PRINTF(" hcchar: 0x%08x\n", hcchar.d32); ++ DWC_PRINTF(" hctsiz: 0x%08x\n", hctsiz.d32); ++ DWC_PRINTF(" hcint: 0x%08x\n", hcint.d32); ++ DWC_PRINTF(" hcintmsk: 0x%08x\n", hcintmsk.d32); ++ } ++ if (hc->xfer_started && hc->qh) { ++ dwc_otg_qtd_t *qtd; ++ dwc_otg_hcd_urb_t *urb; ++ ++ DWC_CIRCLEQ_FOREACH(qtd, &hc->qh->qtd_list, qtd_list_entry) { ++ if (!qtd->in_process) ++ break; ++ ++ urb = qtd->urb; ++ DWC_PRINTF(" URB Info:\n"); ++ DWC_PRINTF(" qtd: %p, urb: %p\n", qtd, urb); ++ if (urb) { ++ DWC_PRINTF(" Dev: %d, EP: %d %s\n", ++ dwc_otg_hcd_get_dev_addr(&urb-> ++ pipe_info), ++ dwc_otg_hcd_get_ep_num(&urb-> ++ pipe_info), ++ dwc_otg_hcd_is_pipe_in(&urb-> ++ pipe_info) ? ++ "IN" : "OUT"); ++ DWC_PRINTF(" Max packet size: %d\n", ++ dwc_otg_hcd_get_mps(&urb-> ++ pipe_info)); ++ DWC_PRINTF(" transfer_buffer: %p\n", ++ urb->buf); ++ DWC_PRINTF(" transfer_dma: %p\n", ++ (void *)urb->dma); ++ DWC_PRINTF(" transfer_buffer_length: %d\n", ++ urb->length); ++ DWC_PRINTF(" actual_length: %d\n", ++ urb->actual_length); ++ } ++ } ++ } ++ } ++ DWC_PRINTF(" non_periodic_channels: %d\n", hcd->non_periodic_channels); ++ DWC_PRINTF(" periodic_channels: %d\n", hcd->periodic_channels); ++ DWC_PRINTF(" periodic_usecs: %d\n", hcd->periodic_usecs); ++ np_tx_status.d32 = ++ DWC_READ_REG32(&hcd->core_if->core_global_regs->gnptxsts); ++ DWC_PRINTF(" NP Tx Req Queue Space Avail: %d\n", ++ np_tx_status.b.nptxqspcavail); ++ DWC_PRINTF(" NP Tx FIFO Space Avail: %d\n", ++ np_tx_status.b.nptxfspcavail); ++ p_tx_status.d32 = ++ DWC_READ_REG32(&hcd->core_if->host_if->host_global_regs->hptxsts); ++ DWC_PRINTF(" P Tx Req Queue Space Avail: %d\n", ++ p_tx_status.b.ptxqspcavail); ++ DWC_PRINTF(" P Tx FIFO Space Avail: %d\n", p_tx_status.b.ptxfspcavail); ++ dwc_otg_hcd_dump_frrem(hcd); ++ dwc_otg_dump_global_registers(hcd->core_if); ++ dwc_otg_dump_host_registers(hcd->core_if); ++ DWC_PRINTF ++ ("************************************************************\n"); ++ DWC_PRINTF("\n"); ++#endif ++} ++ ++#ifdef DEBUG ++void dwc_print_setup_data(uint8_t * setup) ++{ ++ int i; ++ if (CHK_DEBUG_LEVEL(DBG_HCD)) { ++ DWC_PRINTF("Setup Data = MSB "); ++ for (i = 7; i >= 0; i--) ++ DWC_PRINTF("%02x ", setup[i]); ++ DWC_PRINTF("\n"); ++ DWC_PRINTF(" bmRequestType Tranfer = %s\n", ++ (setup[0] & 0x80) ? "Device-to-Host" : ++ "Host-to-Device"); ++ DWC_PRINTF(" bmRequestType Type = "); ++ switch ((setup[0] & 0x60) >> 5) { ++ case 0: ++ DWC_PRINTF("Standard\n"); ++ break; ++ case 1: ++ DWC_PRINTF("Class\n"); ++ break; ++ case 2: ++ DWC_PRINTF("Vendor\n"); ++ break; ++ case 3: ++ DWC_PRINTF("Reserved\n"); ++ break; ++ } ++ DWC_PRINTF(" bmRequestType Recipient = "); ++ switch (setup[0] & 0x1f) { ++ case 0: ++ DWC_PRINTF("Device\n"); ++ break; ++ case 1: ++ DWC_PRINTF("Interface\n"); ++ break; ++ case 2: ++ DWC_PRINTF("Endpoint\n"); ++ break; ++ case 3: ++ DWC_PRINTF("Other\n"); ++ break; ++ default: ++ DWC_PRINTF("Reserved\n"); ++ break; ++ } ++ DWC_PRINTF(" bRequest = 0x%0x\n", setup[1]); ++ DWC_PRINTF(" wValue = 0x%0x\n", *((uint16_t *) & setup[2])); ++ DWC_PRINTF(" wIndex = 0x%0x\n", *((uint16_t *) & setup[4])); ++ DWC_PRINTF(" wLength = 0x%0x\n\n", *((uint16_t *) & setup[6])); ++ } ++} ++#endif ++ ++void dwc_otg_hcd_dump_frrem(dwc_otg_hcd_t * hcd) ++{ ++#if 0 ++ DWC_PRINTF("Frame remaining at SOF:\n"); ++ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n", ++ hcd->frrem_samples, hcd->frrem_accum, ++ (hcd->frrem_samples > 0) ? ++ hcd->frrem_accum / hcd->frrem_samples : 0); ++ ++ DWC_PRINTF("\n"); ++ DWC_PRINTF("Frame remaining at start_transfer (uframe 7):\n"); ++ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n", ++ hcd->core_if->hfnum_7_samples, ++ hcd->core_if->hfnum_7_frrem_accum, ++ (hcd->core_if->hfnum_7_samples > ++ 0) ? hcd->core_if->hfnum_7_frrem_accum / ++ hcd->core_if->hfnum_7_samples : 0); ++ DWC_PRINTF("Frame remaining at start_transfer (uframe 0):\n"); ++ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n", ++ hcd->core_if->hfnum_0_samples, ++ hcd->core_if->hfnum_0_frrem_accum, ++ (hcd->core_if->hfnum_0_samples > ++ 0) ? hcd->core_if->hfnum_0_frrem_accum / ++ hcd->core_if->hfnum_0_samples : 0); ++ DWC_PRINTF("Frame remaining at start_transfer (uframe 1-6):\n"); ++ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n", ++ hcd->core_if->hfnum_other_samples, ++ hcd->core_if->hfnum_other_frrem_accum, ++ (hcd->core_if->hfnum_other_samples > ++ 0) ? hcd->core_if->hfnum_other_frrem_accum / ++ hcd->core_if->hfnum_other_samples : 0); ++ ++ DWC_PRINTF("\n"); ++ DWC_PRINTF("Frame remaining at sample point A (uframe 7):\n"); ++ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n", ++ hcd->hfnum_7_samples_a, hcd->hfnum_7_frrem_accum_a, ++ (hcd->hfnum_7_samples_a > 0) ? ++ hcd->hfnum_7_frrem_accum_a / hcd->hfnum_7_samples_a : 0); ++ DWC_PRINTF("Frame remaining at sample point A (uframe 0):\n"); ++ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n", ++ hcd->hfnum_0_samples_a, hcd->hfnum_0_frrem_accum_a, ++ (hcd->hfnum_0_samples_a > 0) ? ++ hcd->hfnum_0_frrem_accum_a / hcd->hfnum_0_samples_a : 0); ++ DWC_PRINTF("Frame remaining at sample point A (uframe 1-6):\n"); ++ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n", ++ hcd->hfnum_other_samples_a, hcd->hfnum_other_frrem_accum_a, ++ (hcd->hfnum_other_samples_a > 0) ? ++ hcd->hfnum_other_frrem_accum_a / ++ hcd->hfnum_other_samples_a : 0); ++ ++ DWC_PRINTF("\n"); ++ DWC_PRINTF("Frame remaining at sample point B (uframe 7):\n"); ++ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n", ++ hcd->hfnum_7_samples_b, hcd->hfnum_7_frrem_accum_b, ++ (hcd->hfnum_7_samples_b > 0) ? ++ hcd->hfnum_7_frrem_accum_b / hcd->hfnum_7_samples_b : 0); ++ DWC_PRINTF("Frame remaining at sample point B (uframe 0):\n"); ++ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n", ++ hcd->hfnum_0_samples_b, hcd->hfnum_0_frrem_accum_b, ++ (hcd->hfnum_0_samples_b > 0) ? ++ hcd->hfnum_0_frrem_accum_b / hcd->hfnum_0_samples_b : 0); ++ DWC_PRINTF("Frame remaining at sample point B (uframe 1-6):\n"); ++ DWC_PRINTF(" samples %u, accum %llu, avg %llu\n", ++ hcd->hfnum_other_samples_b, hcd->hfnum_other_frrem_accum_b, ++ (hcd->hfnum_other_samples_b > 0) ? ++ hcd->hfnum_other_frrem_accum_b / ++ hcd->hfnum_other_samples_b : 0); ++#endif ++} ++ ++#endif /* DWC_DEVICE_ONLY */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd.h +@@ -0,0 +1,870 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd.h $ ++ * $Revision: #58 $ ++ * $Date: 2011/09/15 $ ++ * $Change: 1846647 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++#ifndef DWC_DEVICE_ONLY ++#ifndef __DWC_HCD_H__ ++#define __DWC_HCD_H__ ++ ++#include "dwc_otg_os_dep.h" ++#include "usb.h" ++#include "dwc_otg_hcd_if.h" ++#include "dwc_otg_core_if.h" ++#include "dwc_list.h" ++#include "dwc_otg_cil.h" ++#include "dwc_otg_fiq_fsm.h" ++#include "dwc_otg_driver.h" ++ ++ ++/** ++ * @file ++ * ++ * This file contains the structures, constants, and interfaces for ++ * the Host Contoller Driver (HCD). ++ * ++ * The Host Controller Driver (HCD) is responsible for translating requests ++ * from the USB Driver into the appropriate actions on the DWC_otg controller. ++ * It isolates the USBD from the specifics of the controller by providing an ++ * API to the USBD. ++ */ ++ ++struct dwc_otg_hcd_pipe_info { ++ uint8_t dev_addr; ++ uint8_t ep_num; ++ uint8_t pipe_type; ++ uint8_t pipe_dir; ++ uint16_t mps; ++}; ++ ++struct dwc_otg_hcd_iso_packet_desc { ++ uint32_t offset; ++ uint32_t length; ++ uint32_t actual_length; ++ uint32_t status; ++}; ++ ++struct dwc_otg_qtd; ++ ++struct dwc_otg_hcd_urb { ++ void *priv; ++ struct dwc_otg_qtd *qtd; ++ void *buf; ++ dwc_dma_t dma; ++ void *setup_packet; ++ dwc_dma_t setup_dma; ++ uint32_t length; ++ uint32_t actual_length; ++ uint32_t status; ++ uint32_t error_count; ++ uint32_t packet_count; ++ uint32_t flags; ++ uint16_t interval; ++ struct dwc_otg_hcd_pipe_info pipe_info; ++ struct dwc_otg_hcd_iso_packet_desc iso_descs[0]; ++}; ++ ++static inline uint8_t dwc_otg_hcd_get_ep_num(struct dwc_otg_hcd_pipe_info *pipe) ++{ ++ return pipe->ep_num; ++} ++ ++static inline uint8_t dwc_otg_hcd_get_pipe_type(struct dwc_otg_hcd_pipe_info ++ *pipe) ++{ ++ return pipe->pipe_type; ++} ++ ++static inline uint16_t dwc_otg_hcd_get_mps(struct dwc_otg_hcd_pipe_info *pipe) ++{ ++ return pipe->mps; ++} ++ ++static inline uint8_t dwc_otg_hcd_get_dev_addr(struct dwc_otg_hcd_pipe_info ++ *pipe) ++{ ++ return pipe->dev_addr; ++} ++ ++static inline uint8_t dwc_otg_hcd_is_pipe_isoc(struct dwc_otg_hcd_pipe_info ++ *pipe) ++{ ++ return (pipe->pipe_type == UE_ISOCHRONOUS); ++} ++ ++static inline uint8_t dwc_otg_hcd_is_pipe_int(struct dwc_otg_hcd_pipe_info ++ *pipe) ++{ ++ return (pipe->pipe_type == UE_INTERRUPT); ++} ++ ++static inline uint8_t dwc_otg_hcd_is_pipe_bulk(struct dwc_otg_hcd_pipe_info ++ *pipe) ++{ ++ return (pipe->pipe_type == UE_BULK); ++} ++ ++static inline uint8_t dwc_otg_hcd_is_pipe_control(struct dwc_otg_hcd_pipe_info ++ *pipe) ++{ ++ return (pipe->pipe_type == UE_CONTROL); ++} ++ ++static inline uint8_t dwc_otg_hcd_is_pipe_in(struct dwc_otg_hcd_pipe_info *pipe) ++{ ++ return (pipe->pipe_dir == UE_DIR_IN); ++} ++ ++static inline uint8_t dwc_otg_hcd_is_pipe_out(struct dwc_otg_hcd_pipe_info ++ *pipe) ++{ ++ return (!dwc_otg_hcd_is_pipe_in(pipe)); ++} ++ ++static inline void dwc_otg_hcd_fill_pipe(struct dwc_otg_hcd_pipe_info *pipe, ++ uint8_t devaddr, uint8_t ep_num, ++ uint8_t pipe_type, uint8_t pipe_dir, ++ uint16_t mps) ++{ ++ pipe->dev_addr = devaddr; ++ pipe->ep_num = ep_num; ++ pipe->pipe_type = pipe_type; ++ pipe->pipe_dir = pipe_dir; ++ pipe->mps = mps; ++} ++ ++/** ++ * Phases for control transfers. ++ */ ++typedef enum dwc_otg_control_phase { ++ DWC_OTG_CONTROL_SETUP, ++ DWC_OTG_CONTROL_DATA, ++ DWC_OTG_CONTROL_STATUS ++} dwc_otg_control_phase_e; ++ ++/** Transaction types. */ ++typedef enum dwc_otg_transaction_type { ++ DWC_OTG_TRANSACTION_NONE = 0, ++ DWC_OTG_TRANSACTION_PERIODIC = 1, ++ DWC_OTG_TRANSACTION_NON_PERIODIC = 2, ++ DWC_OTG_TRANSACTION_ALL = DWC_OTG_TRANSACTION_PERIODIC + DWC_OTG_TRANSACTION_NON_PERIODIC ++} dwc_otg_transaction_type_e; ++ ++struct dwc_otg_qh; ++ ++/** ++ * A Queue Transfer Descriptor (QTD) holds the state of a bulk, control, ++ * interrupt, or isochronous transfer. A single QTD is created for each URB ++ * (of one of these types) submitted to the HCD. The transfer associated with ++ * a QTD may require one or multiple transactions. ++ * ++ * A QTD is linked to a Queue Head, which is entered in either the ++ * non-periodic or periodic schedule for execution. When a QTD is chosen for ++ * execution, some or all of its transactions may be executed. After ++ * execution, the state of the QTD is updated. The QTD may be retired if all ++ * its transactions are complete or if an error occurred. Otherwise, it ++ * remains in the schedule so more transactions can be executed later. ++ */ ++typedef struct dwc_otg_qtd { ++ /** ++ * Determines the PID of the next data packet for the data phase of ++ * control transfers. Ignored for other transfer types.
++ * One of the following values: ++ * - DWC_OTG_HC_PID_DATA0 ++ * - DWC_OTG_HC_PID_DATA1 ++ */ ++ uint8_t data_toggle; ++ ++ /** Current phase for control transfers (Setup, Data, or Status). */ ++ dwc_otg_control_phase_e control_phase; ++ ++ /** Keep track of the current split type ++ * for FS/LS endpoints on a HS Hub */ ++ uint8_t complete_split; ++ ++ /** How many bytes transferred during SSPLIT OUT */ ++ uint32_t ssplit_out_xfer_count; ++ ++ /** ++ * Holds the number of bus errors that have occurred for a transaction ++ * within this transfer. ++ */ ++ uint8_t error_count; ++ ++ /** ++ * Index of the next frame descriptor for an isochronous transfer. A ++ * frame descriptor describes the buffer position and length of the ++ * data to be transferred in the next scheduled (micro)frame of an ++ * isochronous transfer. It also holds status for that transaction. ++ * The frame index starts at 0. ++ */ ++ uint16_t isoc_frame_index; ++ ++ /** Position of the ISOC split on full/low speed */ ++ uint8_t isoc_split_pos; ++ ++ /** Position of the ISOC split in the buffer for the current frame */ ++ uint16_t isoc_split_offset; ++ ++ /** URB for this transfer */ ++ struct dwc_otg_hcd_urb *urb; ++ ++ struct dwc_otg_qh *qh; ++ ++ /** This list of QTDs */ ++ DWC_CIRCLEQ_ENTRY(dwc_otg_qtd) qtd_list_entry; ++ ++ /** Indicates if this QTD is currently processed by HW. */ ++ uint8_t in_process; ++ ++ /** Number of DMA descriptors for this QTD */ ++ uint8_t n_desc; ++ ++ /** ++ * Last activated frame(packet) index. ++ * Used in Descriptor DMA mode only. ++ */ ++ uint16_t isoc_frame_index_last; ++ ++} dwc_otg_qtd_t; ++ ++DWC_CIRCLEQ_HEAD(dwc_otg_qtd_list, dwc_otg_qtd); ++ ++/** ++ * A Queue Head (QH) holds the static characteristics of an endpoint and ++ * maintains a list of transfers (QTDs) for that endpoint. A QH structure may ++ * be entered in either the non-periodic or periodic schedule. ++ */ ++typedef struct dwc_otg_qh { ++ /** ++ * Endpoint type. ++ * One of the following values: ++ * - UE_CONTROL ++ * - UE_BULK ++ * - UE_INTERRUPT ++ * - UE_ISOCHRONOUS ++ */ ++ uint8_t ep_type; ++ uint8_t ep_is_in; ++ ++ /** wMaxPacketSize Field of Endpoint Descriptor. */ ++ uint16_t maxp; ++ ++ /** ++ * Device speed. ++ * One of the following values: ++ * - DWC_OTG_EP_SPEED_LOW ++ * - DWC_OTG_EP_SPEED_FULL ++ * - DWC_OTG_EP_SPEED_HIGH ++ */ ++ uint8_t dev_speed; ++ ++ /** ++ * Determines the PID of the next data packet for non-control ++ * transfers. Ignored for control transfers.
++ * One of the following values: ++ * - DWC_OTG_HC_PID_DATA0 ++ * - DWC_OTG_HC_PID_DATA1 ++ */ ++ uint8_t data_toggle; ++ ++ /** Ping state if 1. */ ++ uint8_t ping_state; ++ ++ /** ++ * List of QTDs for this QH. ++ */ ++ struct dwc_otg_qtd_list qtd_list; ++ ++ /** Host channel currently processing transfers for this QH. */ ++ struct dwc_hc *channel; ++ ++ /** Full/low speed endpoint on high-speed hub requires split. */ ++ uint8_t do_split; ++ ++ /** @name Periodic schedule information */ ++ /** @{ */ ++ ++ /** Bandwidth in microseconds per (micro)frame. */ ++ uint16_t usecs; ++ ++ /** Interval between transfers in (micro)frames. */ ++ uint16_t interval; ++ ++ /** ++ * (micro)frame to initialize a periodic transfer. The transfer ++ * executes in the following (micro)frame. ++ */ ++ uint16_t sched_frame; ++ ++ /* ++ ** Frame a NAK was received on this queue head, used to minimise NAK retransmission ++ */ ++ uint16_t nak_frame; ++ ++ /** (micro)frame at which last start split was initialized. */ ++ uint16_t start_split_frame; ++ ++ /** @} */ ++ ++ /** ++ * Used instead of original buffer if ++ * it(physical address) is not dword-aligned. ++ */ ++ uint8_t *dw_align_buf; ++ dwc_dma_t dw_align_buf_dma; ++ ++ /** Entry for QH in either the periodic or non-periodic schedule. */ ++ dwc_list_link_t qh_list_entry; ++ ++ /** @name Descriptor DMA support */ ++ /** @{ */ ++ ++ /** Descriptor List. */ ++ dwc_otg_host_dma_desc_t *desc_list; ++ ++ /** Descriptor List physical address. */ ++ dwc_dma_t desc_list_dma; ++ ++ /** ++ * Xfer Bytes array. ++ * Each element corresponds to a descriptor and indicates ++ * original XferSize size value for the descriptor. ++ */ ++ uint32_t *n_bytes; ++ ++ /** Actual number of transfer descriptors in a list. */ ++ uint16_t ntd; ++ ++ /** First activated isochronous transfer descriptor index. */ ++ uint8_t td_first; ++ /** Last activated isochronous transfer descriptor index. */ ++ uint8_t td_last; ++ ++ /** @} */ ++ ++ ++ uint16_t speed; ++ uint16_t frame_usecs[8]; ++ ++ uint32_t skip_count; ++} dwc_otg_qh_t; ++ ++DWC_CIRCLEQ_HEAD(hc_list, dwc_hc); ++ ++typedef struct urb_tq_entry { ++ struct urb *urb; ++ DWC_TAILQ_ENTRY(urb_tq_entry) urb_tq_entries; ++} urb_tq_entry_t; ++ ++DWC_TAILQ_HEAD(urb_list, urb_tq_entry); ++ ++/** ++ * This structure holds the state of the HCD, including the non-periodic and ++ * periodic schedules. ++ */ ++struct dwc_otg_hcd { ++ /** The DWC otg device pointer */ ++ struct dwc_otg_device *otg_dev; ++ /** DWC OTG Core Interface Layer */ ++ dwc_otg_core_if_t *core_if; ++ ++ /** Function HCD driver callbacks */ ++ struct dwc_otg_hcd_function_ops *fops; ++ ++ /** Internal DWC HCD Flags */ ++ volatile union dwc_otg_hcd_internal_flags { ++ uint32_t d32; ++ struct { ++ unsigned port_connect_status_change:1; ++ unsigned port_connect_status:1; ++ unsigned port_reset_change:1; ++ unsigned port_enable_change:1; ++ unsigned port_suspend_change:1; ++ unsigned port_over_current_change:1; ++ unsigned port_l1_change:1; ++ unsigned port_speed:2; ++ unsigned reserved:24; ++ } b; ++ } flags; ++ ++ /** ++ * Inactive items in the non-periodic schedule. This is a list of ++ * Queue Heads. Transfers associated with these Queue Heads are not ++ * currently assigned to a host channel. ++ */ ++ dwc_list_link_t non_periodic_sched_inactive; ++ ++ /** ++ * Active items in the non-periodic schedule. This is a list of ++ * Queue Heads. Transfers associated with these Queue Heads are ++ * currently assigned to a host channel. ++ */ ++ dwc_list_link_t non_periodic_sched_active; ++ ++ /** ++ * Pointer to the next Queue Head to process in the active ++ * non-periodic schedule. ++ */ ++ dwc_list_link_t *non_periodic_qh_ptr; ++ ++ /** ++ * Inactive items in the periodic schedule. This is a list of QHs for ++ * periodic transfers that are _not_ scheduled for the next frame. ++ * Each QH in the list has an interval counter that determines when it ++ * needs to be scheduled for execution. This scheduling mechanism ++ * allows only a simple calculation for periodic bandwidth used (i.e. ++ * must assume that all periodic transfers may need to execute in the ++ * same frame). However, it greatly simplifies scheduling and should ++ * be sufficient for the vast majority of OTG hosts, which need to ++ * connect to a small number of peripherals at one time. ++ * ++ * Items move from this list to periodic_sched_ready when the QH ++ * interval counter is 0 at SOF. ++ */ ++ dwc_list_link_t periodic_sched_inactive; ++ ++ /** ++ * List of periodic QHs that are ready for execution in the next ++ * frame, but have not yet been assigned to host channels. ++ * ++ * Items move from this list to periodic_sched_assigned as host ++ * channels become available during the current frame. ++ */ ++ dwc_list_link_t periodic_sched_ready; ++ ++ /** ++ * List of periodic QHs to be executed in the next frame that are ++ * assigned to host channels. ++ * ++ * Items move from this list to periodic_sched_queued as the ++ * transactions for the QH are queued to the DWC_otg controller. ++ */ ++ dwc_list_link_t periodic_sched_assigned; ++ ++ /** ++ * List of periodic QHs that have been queued for execution. ++ * ++ * Items move from this list to either periodic_sched_inactive or ++ * periodic_sched_ready when the channel associated with the transfer ++ * is released. If the interval for the QH is 1, the item moves to ++ * periodic_sched_ready because it must be rescheduled for the next ++ * frame. Otherwise, the item moves to periodic_sched_inactive. ++ */ ++ dwc_list_link_t periodic_sched_queued; ++ ++ /** ++ * Total bandwidth claimed so far for periodic transfers. This value ++ * is in microseconds per (micro)frame. The assumption is that all ++ * periodic transfers may occur in the same (micro)frame. ++ */ ++ uint16_t periodic_usecs; ++ ++ /** ++ * Total bandwidth claimed so far for all periodic transfers ++ * in a frame. ++ * This will include a mixture of HS and FS transfers. ++ * Units are microseconds per (micro)frame. ++ * We have a budget per frame and have to schedule ++ * transactions accordingly. ++ * Watch out for the fact that things are actually scheduled for the ++ * "next frame". ++ */ ++ uint16_t frame_usecs[8]; ++ ++ ++ /** ++ * Frame number read from the core at SOF. The value ranges from 0 to ++ * DWC_HFNUM_MAX_FRNUM. ++ */ ++ uint16_t frame_number; ++ ++ /** ++ * Count of periodic QHs, if using several eps. For SOF enable/disable. ++ */ ++ uint16_t periodic_qh_count; ++ ++ /** ++ * Free host channels in the controller. This is a list of ++ * dwc_hc_t items. ++ */ ++ struct hc_list free_hc_list; ++ /** ++ * Number of host channels assigned to periodic transfers. Currently ++ * assuming that there is a dedicated host channel for each periodic ++ * transaction and at least one host channel available for ++ * non-periodic transactions. ++ */ ++ int periodic_channels; /* microframe_schedule==0 */ ++ ++ /** ++ * Number of host channels assigned to non-periodic transfers. ++ */ ++ int non_periodic_channels; /* microframe_schedule==0 */ ++ ++ /** ++ * Number of host channels assigned to non-periodic transfers. ++ */ ++ int available_host_channels; ++ ++ /** ++ * Array of pointers to the host channel descriptors. Allows accessing ++ * a host channel descriptor given the host channel number. This is ++ * useful in interrupt handlers. ++ */ ++ struct dwc_hc *hc_ptr_array[MAX_EPS_CHANNELS]; ++ ++ /** ++ * Buffer to use for any data received during the status phase of a ++ * control transfer. Normally no data is transferred during the status ++ * phase. This buffer is used as a bit bucket. ++ */ ++ uint8_t *status_buf; ++ ++ /** ++ * DMA address for status_buf. ++ */ ++ dma_addr_t status_buf_dma; ++#define DWC_OTG_HCD_STATUS_BUF_SIZE 64 ++ ++ /** ++ * Connection timer. An OTG host must display a message if the device ++ * does not connect. Started when the VBus power is turned on via ++ * sysfs attribute "buspower". ++ */ ++ dwc_timer_t *conn_timer; ++ ++ /* Tasket to do a reset */ ++ dwc_tasklet_t *reset_tasklet; ++ ++ dwc_tasklet_t *completion_tasklet; ++ struct urb_list completed_urb_list; ++ ++ /* */ ++ dwc_spinlock_t *lock; ++ /** ++ * Private data that could be used by OS wrapper. ++ */ ++ void *priv; ++ ++ uint8_t otg_port; ++ ++ /** Frame List */ ++ uint32_t *frame_list; ++ ++ /** Hub - Port assignment */ ++ int hub_port[128]; ++#ifdef FIQ_DEBUG ++ int hub_port_alloc[2048]; ++#endif ++ ++ /** Frame List DMA address */ ++ dma_addr_t frame_list_dma; ++ ++ struct fiq_stack *fiq_stack; ++ struct fiq_state *fiq_state; ++ ++ /** Virtual address for split transaction DMA bounce buffers */ ++ struct fiq_dma_blob *fiq_dmab; ++ ++#ifdef DEBUG ++ uint32_t frrem_samples; ++ uint64_t frrem_accum; ++ ++ uint32_t hfnum_7_samples_a; ++ uint64_t hfnum_7_frrem_accum_a; ++ uint32_t hfnum_0_samples_a; ++ uint64_t hfnum_0_frrem_accum_a; ++ uint32_t hfnum_other_samples_a; ++ uint64_t hfnum_other_frrem_accum_a; ++ ++ uint32_t hfnum_7_samples_b; ++ uint64_t hfnum_7_frrem_accum_b; ++ uint32_t hfnum_0_samples_b; ++ uint64_t hfnum_0_frrem_accum_b; ++ uint32_t hfnum_other_samples_b; ++ uint64_t hfnum_other_frrem_accum_b; ++#endif ++}; ++ ++static inline struct device *dwc_otg_hcd_to_dev(struct dwc_otg_hcd *hcd) ++{ ++ return &hcd->otg_dev->os_dep.platformdev->dev; ++} ++ ++/** @name Transaction Execution Functions */ ++/** @{ */ ++extern dwc_otg_transaction_type_e dwc_otg_hcd_select_transactions(dwc_otg_hcd_t ++ * hcd); ++extern void dwc_otg_hcd_queue_transactions(dwc_otg_hcd_t * hcd, ++ dwc_otg_transaction_type_e tr_type); ++ ++int dwc_otg_hcd_allocate_port(dwc_otg_hcd_t * hcd, dwc_otg_qh_t *qh); ++void dwc_otg_hcd_release_port(dwc_otg_hcd_t * dwc_otg_hcd, dwc_otg_qh_t *qh); ++ ++extern int fiq_fsm_queue_transaction(dwc_otg_hcd_t *hcd, dwc_otg_qh_t *qh); ++extern int fiq_fsm_transaction_suitable(dwc_otg_hcd_t *hcd, dwc_otg_qh_t *qh); ++extern void dwc_otg_cleanup_fiq_channel(dwc_otg_hcd_t *hcd, uint32_t num); ++ ++/** @} */ ++ ++/** @name Interrupt Handler Functions */ ++/** @{ */ ++extern int32_t dwc_otg_hcd_handle_intr(dwc_otg_hcd_t * dwc_otg_hcd); ++extern int32_t dwc_otg_hcd_handle_sof_intr(dwc_otg_hcd_t * dwc_otg_hcd); ++extern int32_t dwc_otg_hcd_handle_rx_status_q_level_intr(dwc_otg_hcd_t * ++ dwc_otg_hcd); ++extern int32_t dwc_otg_hcd_handle_np_tx_fifo_empty_intr(dwc_otg_hcd_t * ++ dwc_otg_hcd); ++extern int32_t dwc_otg_hcd_handle_perio_tx_fifo_empty_intr(dwc_otg_hcd_t * ++ dwc_otg_hcd); ++extern int32_t dwc_otg_hcd_handle_incomplete_periodic_intr(dwc_otg_hcd_t * ++ dwc_otg_hcd); ++extern int32_t dwc_otg_hcd_handle_port_intr(dwc_otg_hcd_t * dwc_otg_hcd); ++extern int32_t dwc_otg_hcd_handle_conn_id_status_change_intr(dwc_otg_hcd_t * ++ dwc_otg_hcd); ++extern int32_t dwc_otg_hcd_handle_disconnect_intr(dwc_otg_hcd_t * dwc_otg_hcd); ++extern int32_t dwc_otg_hcd_handle_hc_intr(dwc_otg_hcd_t * dwc_otg_hcd); ++extern int32_t dwc_otg_hcd_handle_hc_n_intr(dwc_otg_hcd_t * dwc_otg_hcd, ++ uint32_t num); ++extern int32_t dwc_otg_hcd_handle_session_req_intr(dwc_otg_hcd_t * dwc_otg_hcd); ++extern int32_t dwc_otg_hcd_handle_wakeup_detected_intr(dwc_otg_hcd_t * ++ dwc_otg_hcd); ++/** @} */ ++ ++/** @name Schedule Queue Functions */ ++/** @{ */ ++ ++/* Implemented in dwc_otg_hcd_queue.c */ ++extern dwc_otg_qh_t *dwc_otg_hcd_qh_create(dwc_otg_hcd_t * hcd, ++ dwc_otg_hcd_urb_t * urb, int atomic_alloc); ++extern void dwc_otg_hcd_qh_free(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh); ++extern int dwc_otg_hcd_qh_add(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh); ++extern void dwc_otg_hcd_qh_remove(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh); ++extern void dwc_otg_hcd_qh_deactivate(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh, ++ int sched_csplit); ++ ++/** Remove and free a QH */ ++static inline void dwc_otg_hcd_qh_remove_and_free(dwc_otg_hcd_t * hcd, ++ dwc_otg_qh_t * qh) ++{ ++ dwc_irqflags_t flags; ++ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags); ++ dwc_otg_hcd_qh_remove(hcd, qh); ++ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags); ++ dwc_otg_hcd_qh_free(hcd, qh); ++} ++ ++/** Allocates memory for a QH structure. ++ * @return Returns the memory allocate or NULL on error. */ ++static inline dwc_otg_qh_t *dwc_otg_hcd_qh_alloc(int atomic_alloc) ++{ ++ if (atomic_alloc) ++ return (dwc_otg_qh_t *) DWC_ALLOC_ATOMIC(sizeof(dwc_otg_qh_t)); ++ else ++ return (dwc_otg_qh_t *) DWC_ALLOC(sizeof(dwc_otg_qh_t)); ++} ++ ++extern dwc_otg_qtd_t *dwc_otg_hcd_qtd_create(dwc_otg_hcd_urb_t * urb, ++ int atomic_alloc); ++extern void dwc_otg_hcd_qtd_init(dwc_otg_qtd_t * qtd, dwc_otg_hcd_urb_t * urb); ++extern int dwc_otg_hcd_qtd_add(dwc_otg_qtd_t * qtd, dwc_otg_hcd_t * dwc_otg_hcd, ++ dwc_otg_qh_t ** qh, int atomic_alloc); ++ ++/** Allocates memory for a QTD structure. ++ * @return Returns the memory allocate or NULL on error. */ ++static inline dwc_otg_qtd_t *dwc_otg_hcd_qtd_alloc(int atomic_alloc) ++{ ++ if (atomic_alloc) ++ return (dwc_otg_qtd_t *) DWC_ALLOC_ATOMIC(sizeof(dwc_otg_qtd_t)); ++ else ++ return (dwc_otg_qtd_t *) DWC_ALLOC(sizeof(dwc_otg_qtd_t)); ++} ++ ++/** Frees the memory for a QTD structure. QTD should already be removed from ++ * list. ++ * @param qtd QTD to free.*/ ++static inline void dwc_otg_hcd_qtd_free(dwc_otg_qtd_t * qtd) ++{ ++ DWC_FREE(qtd); ++} ++ ++/** Removes a QTD from list. ++ * @param hcd HCD instance. ++ * @param qtd QTD to remove from list. ++ * @param qh QTD belongs to. ++ */ ++static inline void dwc_otg_hcd_qtd_remove(dwc_otg_hcd_t * hcd, ++ dwc_otg_qtd_t * qtd, ++ dwc_otg_qh_t * qh) ++{ ++ DWC_CIRCLEQ_REMOVE(&qh->qtd_list, qtd, qtd_list_entry); ++} ++ ++/** Remove and free a QTD ++ * Need to disable IRQ and hold hcd lock while calling this function out of ++ * interrupt servicing chain */ ++static inline void dwc_otg_hcd_qtd_remove_and_free(dwc_otg_hcd_t * hcd, ++ dwc_otg_qtd_t * qtd, ++ dwc_otg_qh_t * qh) ++{ ++ dwc_otg_hcd_qtd_remove(hcd, qtd, qh); ++ dwc_otg_hcd_qtd_free(qtd); ++} ++ ++/** @} */ ++ ++/** @name Descriptor DMA Supporting Functions */ ++/** @{ */ ++ ++extern void dwc_otg_hcd_start_xfer_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh); ++extern void dwc_otg_hcd_complete_xfer_ddma(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_halt_status_e halt_status); ++ ++extern int dwc_otg_hcd_qh_init_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh); ++extern void dwc_otg_hcd_qh_free_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh); ++ ++/** @} */ ++ ++/** @name Internal Functions */ ++/** @{ */ ++dwc_otg_qh_t *dwc_urb_to_qh(dwc_otg_hcd_urb_t * urb); ++/** @} */ ++ ++#ifdef CONFIG_USB_DWC_OTG_LPM ++extern int dwc_otg_hcd_get_hc_for_lpm_tran(dwc_otg_hcd_t * hcd, ++ uint8_t devaddr); ++extern void dwc_otg_hcd_free_hc_from_lpm(dwc_otg_hcd_t * hcd); ++#endif ++ ++/** Gets the QH that contains the list_head */ ++#define dwc_list_to_qh(_list_head_ptr_) container_of(_list_head_ptr_, dwc_otg_qh_t, qh_list_entry) ++ ++/** Gets the QTD that contains the list_head */ ++#define dwc_list_to_qtd(_list_head_ptr_) container_of(_list_head_ptr_, dwc_otg_qtd_t, qtd_list_entry) ++ ++/** Check if QH is non-periodic */ ++#define dwc_qh_is_non_per(_qh_ptr_) ((_qh_ptr_->ep_type == UE_BULK) || \ ++ (_qh_ptr_->ep_type == UE_CONTROL)) ++ ++/** High bandwidth multiplier as encoded in highspeed endpoint descriptors */ ++#define dwc_hb_mult(wMaxPacketSize) (1 + (((wMaxPacketSize) >> 11) & 0x03)) ++ ++/** Packet size for any kind of endpoint descriptor */ ++#define dwc_max_packet(wMaxPacketSize) ((wMaxPacketSize) & 0x07ff) ++ ++/** ++ * Returns true if _frame1 is less than or equal to _frame2. The comparison is ++ * done modulo DWC_HFNUM_MAX_FRNUM. This accounts for the rollover of the ++ * frame number when the max frame number is reached. ++ */ ++static inline int dwc_frame_num_le(uint16_t frame1, uint16_t frame2) ++{ ++ return ((frame2 - frame1) & DWC_HFNUM_MAX_FRNUM) <= ++ (DWC_HFNUM_MAX_FRNUM >> 1); ++} ++ ++/** ++ * Returns true if _frame1 is greater than _frame2. The comparison is done ++ * modulo DWC_HFNUM_MAX_FRNUM. This accounts for the rollover of the frame ++ * number when the max frame number is reached. ++ */ ++static inline int dwc_frame_num_gt(uint16_t frame1, uint16_t frame2) ++{ ++ return (frame1 != frame2) && ++ (((frame1 - frame2) & DWC_HFNUM_MAX_FRNUM) < ++ (DWC_HFNUM_MAX_FRNUM >> 1)); ++} ++ ++/** ++ * Increments _frame by the amount specified by _inc. The addition is done ++ * modulo DWC_HFNUM_MAX_FRNUM. Returns the incremented value. ++ */ ++static inline uint16_t dwc_frame_num_inc(uint16_t frame, uint16_t inc) ++{ ++ return (frame + inc) & DWC_HFNUM_MAX_FRNUM; ++} ++ ++static inline uint16_t dwc_full_frame_num(uint16_t frame) ++{ ++ return (frame & DWC_HFNUM_MAX_FRNUM) >> 3; ++} ++ ++static inline uint16_t dwc_micro_frame_num(uint16_t frame) ++{ ++ return frame & 0x7; ++} ++ ++extern void init_hcd_usecs(dwc_otg_hcd_t *_hcd); ++ ++void dwc_otg_hcd_save_data_toggle(dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd); ++ ++#ifdef DEBUG ++/** ++ * Macro to sample the remaining PHY clocks left in the current frame. This ++ * may be used during debugging to determine the average time it takes to ++ * execute sections of code. There are two possible sample points, "a" and ++ * "b", so the _letter argument must be one of these values. ++ * ++ * To dump the average sample times, read the "hcd_frrem" sysfs attribute. For ++ * example, "cat /sys/devices/lm0/hcd_frrem". ++ */ ++#define dwc_sample_frrem(_hcd, _qh, _letter) \ ++{ \ ++ hfnum_data_t hfnum; \ ++ dwc_otg_qtd_t *qtd; \ ++ qtd = list_entry(_qh->qtd_list.next, dwc_otg_qtd_t, qtd_list_entry); \ ++ if (usb_pipeint(qtd->urb->pipe) && _qh->start_split_frame != 0 && !qtd->complete_split) { \ ++ hfnum.d32 = DWC_READ_REG32(&_hcd->core_if->host_if->host_global_regs->hfnum); \ ++ switch (hfnum.b.frnum & 0x7) { \ ++ case 7: \ ++ _hcd->hfnum_7_samples_##_letter++; \ ++ _hcd->hfnum_7_frrem_accum_##_letter += hfnum.b.frrem; \ ++ break; \ ++ case 0: \ ++ _hcd->hfnum_0_samples_##_letter++; \ ++ _hcd->hfnum_0_frrem_accum_##_letter += hfnum.b.frrem; \ ++ break; \ ++ default: \ ++ _hcd->hfnum_other_samples_##_letter++; \ ++ _hcd->hfnum_other_frrem_accum_##_letter += hfnum.b.frrem; \ ++ break; \ ++ } \ ++ } \ ++} ++#else ++#define dwc_sample_frrem(_hcd, _qh, _letter) ++#endif ++#endif ++#endif /* DWC_DEVICE_ONLY */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd_ddma.c +@@ -0,0 +1,1134 @@ ++/*========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd_ddma.c $ ++ * $Revision: #10 $ ++ * $Date: 2011/10/20 $ ++ * $Change: 1869464 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++#ifndef DWC_DEVICE_ONLY ++ ++/** @file ++ * This file contains Descriptor DMA support implementation for host mode. ++ */ ++ ++#include "dwc_otg_hcd.h" ++#include "dwc_otg_regs.h" ++ ++extern bool microframe_schedule; ++ ++static inline uint8_t frame_list_idx(uint16_t frame) ++{ ++ return (frame & (MAX_FRLIST_EN_NUM - 1)); ++} ++ ++static inline uint16_t desclist_idx_inc(uint16_t idx, uint16_t inc, uint8_t speed) ++{ ++ return (idx + inc) & ++ (((speed == ++ DWC_OTG_EP_SPEED_HIGH) ? MAX_DMA_DESC_NUM_HS_ISOC : ++ MAX_DMA_DESC_NUM_GENERIC) - 1); ++} ++ ++static inline uint16_t desclist_idx_dec(uint16_t idx, uint16_t inc, uint8_t speed) ++{ ++ return (idx - inc) & ++ (((speed == ++ DWC_OTG_EP_SPEED_HIGH) ? MAX_DMA_DESC_NUM_HS_ISOC : ++ MAX_DMA_DESC_NUM_GENERIC) - 1); ++} ++ ++static inline uint16_t max_desc_num(dwc_otg_qh_t * qh) ++{ ++ return (((qh->ep_type == UE_ISOCHRONOUS) ++ && (qh->dev_speed == DWC_OTG_EP_SPEED_HIGH)) ++ ? MAX_DMA_DESC_NUM_HS_ISOC : MAX_DMA_DESC_NUM_GENERIC); ++} ++static inline uint16_t frame_incr_val(dwc_otg_qh_t * qh) ++{ ++ return ((qh->dev_speed == DWC_OTG_EP_SPEED_HIGH) ++ ? ((qh->interval + 8 - 1) / 8) ++ : qh->interval); ++} ++ ++static int desc_list_alloc(struct device *dev, dwc_otg_qh_t * qh) ++{ ++ int retval = 0; ++ ++ qh->desc_list = (dwc_otg_host_dma_desc_t *) ++ DWC_DMA_ALLOC(dev, sizeof(dwc_otg_host_dma_desc_t) * max_desc_num(qh), ++ &qh->desc_list_dma); ++ ++ if (!qh->desc_list) { ++ retval = -DWC_E_NO_MEMORY; ++ DWC_ERROR("%s: DMA descriptor list allocation failed\n", __func__); ++ ++ } ++ ++ dwc_memset(qh->desc_list, 0x00, ++ sizeof(dwc_otg_host_dma_desc_t) * max_desc_num(qh)); ++ ++ qh->n_bytes = ++ (uint32_t *) DWC_ALLOC(sizeof(uint32_t) * max_desc_num(qh)); ++ ++ if (!qh->n_bytes) { ++ retval = -DWC_E_NO_MEMORY; ++ DWC_ERROR ++ ("%s: Failed to allocate array for descriptors' size actual values\n", ++ __func__); ++ ++ } ++ return retval; ++ ++} ++ ++static void desc_list_free(struct device *dev, dwc_otg_qh_t * qh) ++{ ++ if (qh->desc_list) { ++ DWC_DMA_FREE(dev, max_desc_num(qh), qh->desc_list, ++ qh->desc_list_dma); ++ qh->desc_list = NULL; ++ } ++ ++ if (qh->n_bytes) { ++ DWC_FREE(qh->n_bytes); ++ qh->n_bytes = NULL; ++ } ++} ++ ++static int frame_list_alloc(dwc_otg_hcd_t * hcd) ++{ ++ struct device *dev = dwc_otg_hcd_to_dev(hcd); ++ int retval = 0; ++ ++ if (hcd->frame_list) ++ return 0; ++ ++ hcd->frame_list = DWC_DMA_ALLOC(dev, 4 * MAX_FRLIST_EN_NUM, ++ &hcd->frame_list_dma); ++ if (!hcd->frame_list) { ++ retval = -DWC_E_NO_MEMORY; ++ DWC_ERROR("%s: Frame List allocation failed\n", __func__); ++ } ++ ++ dwc_memset(hcd->frame_list, 0x00, 4 * MAX_FRLIST_EN_NUM); ++ ++ return retval; ++} ++ ++static void frame_list_free(dwc_otg_hcd_t * hcd) ++{ ++ struct device *dev = dwc_otg_hcd_to_dev(hcd); ++ ++ if (!hcd->frame_list) ++ return; ++ ++ DWC_DMA_FREE(dev, 4 * MAX_FRLIST_EN_NUM, hcd->frame_list, hcd->frame_list_dma); ++ hcd->frame_list = NULL; ++} ++ ++static void per_sched_enable(dwc_otg_hcd_t * hcd, uint16_t fr_list_en) ++{ ++ ++ hcfg_data_t hcfg; ++ ++ hcfg.d32 = DWC_READ_REG32(&hcd->core_if->host_if->host_global_regs->hcfg); ++ ++ if (hcfg.b.perschedena) { ++ /* already enabled */ ++ return; ++ } ++ ++ DWC_WRITE_REG32(&hcd->core_if->host_if->host_global_regs->hflbaddr, ++ hcd->frame_list_dma); ++ ++ switch (fr_list_en) { ++ case 64: ++ hcfg.b.frlisten = 3; ++ break; ++ case 32: ++ hcfg.b.frlisten = 2; ++ break; ++ case 16: ++ hcfg.b.frlisten = 1; ++ break; ++ case 8: ++ hcfg.b.frlisten = 0; ++ break; ++ default: ++ break; ++ } ++ ++ hcfg.b.perschedena = 1; ++ ++ DWC_DEBUGPL(DBG_HCD, "Enabling Periodic schedule\n"); ++ DWC_WRITE_REG32(&hcd->core_if->host_if->host_global_regs->hcfg, hcfg.d32); ++ ++} ++ ++static void per_sched_disable(dwc_otg_hcd_t * hcd) ++{ ++ hcfg_data_t hcfg; ++ ++ hcfg.d32 = DWC_READ_REG32(&hcd->core_if->host_if->host_global_regs->hcfg); ++ ++ if (!hcfg.b.perschedena) { ++ /* already disabled */ ++ return; ++ } ++ hcfg.b.perschedena = 0; ++ ++ DWC_DEBUGPL(DBG_HCD, "Disabling Periodic schedule\n"); ++ DWC_WRITE_REG32(&hcd->core_if->host_if->host_global_regs->hcfg, hcfg.d32); ++} ++ ++/* ++ * Activates/Deactivates FrameList entries for the channel ++ * based on endpoint servicing period. ++ */ ++void update_frame_list(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh, uint8_t enable) ++{ ++ uint16_t i, j, inc; ++ dwc_hc_t *hc = NULL; ++ ++ if (!qh->channel) { ++ DWC_ERROR("qh->channel = %p", qh->channel); ++ return; ++ } ++ ++ if (!hcd) { ++ DWC_ERROR("------hcd = %p", hcd); ++ return; ++ } ++ ++ if (!hcd->frame_list) { ++ DWC_ERROR("-------hcd->frame_list = %p", hcd->frame_list); ++ return; ++ } ++ ++ hc = qh->channel; ++ inc = frame_incr_val(qh); ++ if (qh->ep_type == UE_ISOCHRONOUS) ++ i = frame_list_idx(qh->sched_frame); ++ else ++ i = 0; ++ ++ j = i; ++ do { ++ if (enable) ++ hcd->frame_list[j] |= (1 << hc->hc_num); ++ else ++ hcd->frame_list[j] &= ~(1 << hc->hc_num); ++ j = (j + inc) & (MAX_FRLIST_EN_NUM - 1); ++ } ++ while (j != i); ++ if (!enable) ++ return; ++ hc->schinfo = 0; ++ if (qh->channel->speed == DWC_OTG_EP_SPEED_HIGH) { ++ j = 1; ++ /* TODO - check this */ ++ inc = (8 + qh->interval - 1) / qh->interval; ++ for (i = 0; i < inc; i++) { ++ hc->schinfo |= j; ++ j = j << qh->interval; ++ } ++ } else { ++ hc->schinfo = 0xff; ++ } ++} ++ ++#if 1 ++void dump_frame_list(dwc_otg_hcd_t * hcd) ++{ ++ int i = 0; ++ DWC_PRINTF("--FRAME LIST (hex) --\n"); ++ for (i = 0; i < MAX_FRLIST_EN_NUM; i++) { ++ DWC_PRINTF("%x\t", hcd->frame_list[i]); ++ if (!(i % 8) && i) ++ DWC_PRINTF("\n"); ++ } ++ DWC_PRINTF("\n----\n"); ++ ++} ++#endif ++ ++static void release_channel_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ dwc_hc_t *hc = qh->channel; ++ if (dwc_qh_is_non_per(qh)) { ++ if (!microframe_schedule) ++ hcd->non_periodic_channels--; ++ else ++ hcd->available_host_channels++; ++ } else ++ update_frame_list(hcd, qh, 0); ++ ++ /* ++ * The condition is added to prevent double cleanup try in case of device ++ * disconnect. See channel cleanup in dwc_otg_hcd_disconnect_cb(). ++ */ ++ if (hc->qh) { ++ dwc_otg_hc_cleanup(hcd->core_if, hc); ++ DWC_CIRCLEQ_INSERT_TAIL(&hcd->free_hc_list, hc, hc_list_entry); ++ hc->qh = NULL; ++ } ++ ++ qh->channel = NULL; ++ qh->ntd = 0; ++ ++ if (qh->desc_list) { ++ dwc_memset(qh->desc_list, 0x00, ++ sizeof(dwc_otg_host_dma_desc_t) * max_desc_num(qh)); ++ } ++} ++ ++/** ++ * Initializes a QH structure's Descriptor DMA related members. ++ * Allocates memory for descriptor list. ++ * On first periodic QH, allocates memory for FrameList ++ * and enables periodic scheduling. ++ * ++ * @param hcd The HCD state structure for the DWC OTG controller. ++ * @param qh The QH to init. ++ * ++ * @return 0 if successful, negative error code otherwise. ++ */ ++int dwc_otg_hcd_qh_init_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ struct device *dev = dwc_otg_hcd_to_dev(hcd); ++ int retval = 0; ++ ++ if (qh->do_split) { ++ DWC_ERROR("SPLIT Transfers are not supported in Descriptor DMA.\n"); ++ return -1; ++ } ++ ++ retval = desc_list_alloc(dev, qh); ++ ++ if ((retval == 0) ++ && (qh->ep_type == UE_ISOCHRONOUS || qh->ep_type == UE_INTERRUPT)) { ++ if (!hcd->frame_list) { ++ retval = frame_list_alloc(hcd); ++ /* Enable periodic schedule on first periodic QH */ ++ if (retval == 0) ++ per_sched_enable(hcd, MAX_FRLIST_EN_NUM); ++ } ++ } ++ ++ qh->ntd = 0; ++ ++ return retval; ++} ++ ++/** ++ * Frees descriptor list memory associated with the QH. ++ * If QH is periodic and the last, frees FrameList memory ++ * and disables periodic scheduling. ++ * ++ * @param hcd The HCD state structure for the DWC OTG controller. ++ * @param qh The QH to init. ++ */ ++void dwc_otg_hcd_qh_free_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ struct device *dev = dwc_otg_hcd_to_dev(hcd); ++ ++ desc_list_free(dev, qh); ++ ++ /* ++ * Channel still assigned due to some reasons. ++ * Seen on Isoc URB dequeue. Channel halted but no subsequent ++ * ChHalted interrupt to release the channel. Afterwards ++ * when it comes here from endpoint disable routine ++ * channel remains assigned. ++ */ ++ if (qh->channel) ++ release_channel_ddma(hcd, qh); ++ ++ if ((qh->ep_type == UE_ISOCHRONOUS || qh->ep_type == UE_INTERRUPT) ++ && (microframe_schedule || !hcd->periodic_channels) && hcd->frame_list) { ++ ++ per_sched_disable(hcd); ++ frame_list_free(hcd); ++ } ++} ++ ++static uint8_t frame_to_desc_idx(dwc_otg_qh_t * qh, uint16_t frame_idx) ++{ ++ if (qh->dev_speed == DWC_OTG_EP_SPEED_HIGH) { ++ /* ++ * Descriptor set(8 descriptors) index ++ * which is 8-aligned. ++ */ ++ return (frame_idx & ((MAX_DMA_DESC_NUM_HS_ISOC / 8) - 1)) * 8; ++ } else { ++ return (frame_idx & (MAX_DMA_DESC_NUM_GENERIC - 1)); ++ } ++} ++ ++/* ++ * Determine starting frame for Isochronous transfer. ++ * Few frames skipped to prevent race condition with HC. ++ */ ++static uint8_t calc_starting_frame(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh, ++ uint8_t * skip_frames) ++{ ++ uint16_t frame = 0; ++ hcd->frame_number = dwc_otg_hcd_get_frame_number(hcd); ++ ++ /* sched_frame is always frame number(not uFrame) both in FS and HS !! */ ++ ++ /* ++ * skip_frames is used to limit activated descriptors number ++ * to avoid the situation when HC services the last activated ++ * descriptor firstly. ++ * Example for FS: ++ * Current frame is 1, scheduled frame is 3. Since HC always fetches the descriptor ++ * corresponding to curr_frame+1, the descriptor corresponding to frame 2 ++ * will be fetched. If the number of descriptors is max=64 (or greather) the ++ * list will be fully programmed with Active descriptors and it is possible ++ * case(rare) that the latest descriptor(considering rollback) corresponding ++ * to frame 2 will be serviced first. HS case is more probable because, in fact, ++ * up to 11 uframes(16 in the code) may be skipped. ++ */ ++ if (qh->dev_speed == DWC_OTG_EP_SPEED_HIGH) { ++ /* ++ * Consider uframe counter also, to start xfer asap. ++ * If half of the frame elapsed skip 2 frames otherwise ++ * just 1 frame. ++ * Starting descriptor index must be 8-aligned, so ++ * if the current frame is near to complete the next one ++ * is skipped as well. ++ */ ++ ++ if (dwc_micro_frame_num(hcd->frame_number) >= 5) { ++ *skip_frames = 2 * 8; ++ frame = dwc_frame_num_inc(hcd->frame_number, *skip_frames); ++ } else { ++ *skip_frames = 1 * 8; ++ frame = dwc_frame_num_inc(hcd->frame_number, *skip_frames); ++ } ++ ++ frame = dwc_full_frame_num(frame); ++ } else { ++ /* ++ * Two frames are skipped for FS - the current and the next. ++ * But for descriptor programming, 1 frame(descriptor) is enough, ++ * see example above. ++ */ ++ *skip_frames = 1; ++ frame = dwc_frame_num_inc(hcd->frame_number, 2); ++ } ++ ++ return frame; ++} ++ ++/* ++ * Calculate initial descriptor index for isochronous transfer ++ * based on scheduled frame. ++ */ ++static uint8_t recalc_initial_desc_idx(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ uint16_t frame = 0, fr_idx, fr_idx_tmp; ++ uint8_t skip_frames = 0; ++ /* ++ * With current ISOC processing algorithm the channel is being ++ * released when no more QTDs in the list(qh->ntd == 0). ++ * Thus this function is called only when qh->ntd == 0 and qh->channel == 0. ++ * ++ * So qh->channel != NULL branch is not used and just not removed from the ++ * source file. It is required for another possible approach which is, ++ * do not disable and release the channel when ISOC session completed, ++ * just move QH to inactive schedule until new QTD arrives. ++ * On new QTD, the QH moved back to 'ready' schedule, ++ * starting frame and therefore starting desc_index are recalculated. ++ * In this case channel is released only on ep_disable. ++ */ ++ ++ /* Calculate starting descriptor index. For INTERRUPT endpoint it is always 0. */ ++ if (qh->channel) { ++ frame = calc_starting_frame(hcd, qh, &skip_frames); ++ /* ++ * Calculate initial descriptor index based on FrameList current bitmap ++ * and servicing period. ++ */ ++ fr_idx_tmp = frame_list_idx(frame); ++ fr_idx = ++ (MAX_FRLIST_EN_NUM + frame_list_idx(qh->sched_frame) - ++ fr_idx_tmp) ++ % frame_incr_val(qh); ++ fr_idx = (fr_idx + fr_idx_tmp) % MAX_FRLIST_EN_NUM; ++ } else { ++ qh->sched_frame = calc_starting_frame(hcd, qh, &skip_frames); ++ fr_idx = frame_list_idx(qh->sched_frame); ++ } ++ ++ qh->td_first = qh->td_last = frame_to_desc_idx(qh, fr_idx); ++ ++ return skip_frames; ++} ++ ++#define ISOC_URB_GIVEBACK_ASAP ++ ++#define MAX_ISOC_XFER_SIZE_FS 1023 ++#define MAX_ISOC_XFER_SIZE_HS 3072 ++#define DESCNUM_THRESHOLD 4 ++ ++static void init_isoc_dma_desc(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh, ++ uint8_t skip_frames) ++{ ++ struct dwc_otg_hcd_iso_packet_desc *frame_desc; ++ dwc_otg_qtd_t *qtd; ++ dwc_otg_host_dma_desc_t *dma_desc; ++ uint16_t idx, inc, n_desc, ntd_max, max_xfer_size; ++ ++ idx = qh->td_last; ++ inc = qh->interval; ++ n_desc = 0; ++ ++ ntd_max = (max_desc_num(qh) + qh->interval - 1) / qh->interval; ++ if (skip_frames && !qh->channel) ++ ntd_max = ntd_max - skip_frames / qh->interval; ++ ++ max_xfer_size = ++ (qh->dev_speed == ++ DWC_OTG_EP_SPEED_HIGH) ? MAX_ISOC_XFER_SIZE_HS : ++ MAX_ISOC_XFER_SIZE_FS; ++ ++ DWC_CIRCLEQ_FOREACH(qtd, &qh->qtd_list, qtd_list_entry) { ++ while ((qh->ntd < ntd_max) ++ && (qtd->isoc_frame_index_last < ++ qtd->urb->packet_count)) { ++ ++ dma_desc = &qh->desc_list[idx]; ++ dwc_memset(dma_desc, 0x00, sizeof(dwc_otg_host_dma_desc_t)); ++ ++ frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index_last]; ++ ++ if (frame_desc->length > max_xfer_size) ++ qh->n_bytes[idx] = max_xfer_size; ++ else ++ qh->n_bytes[idx] = frame_desc->length; ++ dma_desc->status.b_isoc.n_bytes = qh->n_bytes[idx]; ++ dma_desc->status.b_isoc.a = 1; ++ dma_desc->status.b_isoc.sts = 0; ++ ++ dma_desc->buf = qtd->urb->dma + frame_desc->offset; ++ ++ qh->ntd++; ++ ++ qtd->isoc_frame_index_last++; ++ ++#ifdef ISOC_URB_GIVEBACK_ASAP ++ /* ++ * Set IOC for each descriptor corresponding to the ++ * last frame of the URB. ++ */ ++ if (qtd->isoc_frame_index_last == ++ qtd->urb->packet_count) ++ dma_desc->status.b_isoc.ioc = 1; ++ ++#endif ++ idx = desclist_idx_inc(idx, inc, qh->dev_speed); ++ n_desc++; ++ ++ } ++ qtd->in_process = 1; ++ } ++ ++ qh->td_last = idx; ++ ++#ifdef ISOC_URB_GIVEBACK_ASAP ++ /* Set IOC for the last descriptor if descriptor list is full */ ++ if (qh->ntd == ntd_max) { ++ idx = desclist_idx_dec(qh->td_last, inc, qh->dev_speed); ++ qh->desc_list[idx].status.b_isoc.ioc = 1; ++ } ++#else ++ /* ++ * Set IOC bit only for one descriptor. ++ * Always try to be ahead of HW processing, ++ * i.e. on IOC generation driver activates next descriptors but ++ * core continues to process descriptors followed the one with IOC set. ++ */ ++ ++ if (n_desc > DESCNUM_THRESHOLD) { ++ /* ++ * Move IOC "up". Required even if there is only one QTD ++ * in the list, cause QTDs migth continue to be queued, ++ * but during the activation it was only one queued. ++ * Actually more than one QTD might be in the list if this function called ++ * from XferCompletion - QTDs was queued during HW processing of the previous ++ * descriptor chunk. ++ */ ++ idx = dwc_desclist_idx_dec(idx, inc * ((qh->ntd + 1) / 2), qh->dev_speed); ++ } else { ++ /* ++ * Set the IOC for the latest descriptor ++ * if either number of descriptor is not greather than threshold ++ * or no more new descriptors activated. ++ */ ++ idx = dwc_desclist_idx_dec(qh->td_last, inc, qh->dev_speed); ++ } ++ ++ qh->desc_list[idx].status.b_isoc.ioc = 1; ++#endif ++} ++ ++static void init_non_isoc_dma_desc(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ ++ dwc_hc_t *hc; ++ dwc_otg_host_dma_desc_t *dma_desc; ++ dwc_otg_qtd_t *qtd; ++ int num_packets, len, n_desc = 0; ++ ++ hc = qh->channel; ++ ++ /* ++ * Start with hc->xfer_buff initialized in ++ * assign_and_init_hc(), then if SG transfer consists of multiple URBs, ++ * this pointer re-assigned to the buffer of the currently processed QTD. ++ * For non-SG request there is always one QTD active. ++ */ ++ ++ DWC_CIRCLEQ_FOREACH(qtd, &qh->qtd_list, qtd_list_entry) { ++ ++ if (n_desc) { ++ /* SG request - more than 1 QTDs */ ++ hc->xfer_buff = (uint8_t *)qtd->urb->dma + qtd->urb->actual_length; ++ hc->xfer_len = qtd->urb->length - qtd->urb->actual_length; ++ } ++ ++ qtd->n_desc = 0; ++ ++ do { ++ dma_desc = &qh->desc_list[n_desc]; ++ len = hc->xfer_len; ++ ++ if (len > MAX_DMA_DESC_SIZE) ++ len = MAX_DMA_DESC_SIZE - hc->max_packet + 1; ++ ++ if (hc->ep_is_in) { ++ if (len > 0) { ++ num_packets = (len + hc->max_packet - 1) / hc->max_packet; ++ } else { ++ /* Need 1 packet for transfer length of 0. */ ++ num_packets = 1; ++ } ++ /* Always program an integral # of max packets for IN transfers. */ ++ len = num_packets * hc->max_packet; ++ } ++ ++ dma_desc->status.b.n_bytes = len; ++ ++ qh->n_bytes[n_desc] = len; ++ ++ if ((qh->ep_type == UE_CONTROL) ++ && (qtd->control_phase == DWC_OTG_CONTROL_SETUP)) ++ dma_desc->status.b.sup = 1; /* Setup Packet */ ++ ++ dma_desc->status.b.a = 1; /* Active descriptor */ ++ dma_desc->status.b.sts = 0; ++ ++ dma_desc->buf = ++ ((unsigned long)hc->xfer_buff & 0xffffffff); ++ ++ /* ++ * Last descriptor(or single) of IN transfer ++ * with actual size less than MaxPacket. ++ */ ++ if (len > hc->xfer_len) { ++ hc->xfer_len = 0; ++ } else { ++ hc->xfer_buff += len; ++ hc->xfer_len -= len; ++ } ++ ++ qtd->n_desc++; ++ n_desc++; ++ } ++ while ((hc->xfer_len > 0) && (n_desc != MAX_DMA_DESC_NUM_GENERIC)); ++ ++ ++ qtd->in_process = 1; ++ ++ if (qh->ep_type == UE_CONTROL) ++ break; ++ ++ if (n_desc == MAX_DMA_DESC_NUM_GENERIC) ++ break; ++ } ++ ++ if (n_desc) { ++ /* Request Transfer Complete interrupt for the last descriptor */ ++ qh->desc_list[n_desc - 1].status.b.ioc = 1; ++ /* End of List indicator */ ++ qh->desc_list[n_desc - 1].status.b.eol = 1; ++ ++ hc->ntd = n_desc; ++ } ++} ++ ++/** ++ * For Control and Bulk endpoints initializes descriptor list ++ * and starts the transfer. ++ * ++ * For Interrupt and Isochronous endpoints initializes descriptor list ++ * then updates FrameList, marking appropriate entries as active. ++ * In case of Isochronous, the starting descriptor index is calculated based ++ * on the scheduled frame, but only on the first transfer descriptor within a session. ++ * Then starts the transfer via enabling the channel. ++ * For Isochronous endpoint the channel is not halted on XferComplete ++ * interrupt so remains assigned to the endpoint(QH) until session is done. ++ * ++ * @param hcd The HCD state structure for the DWC OTG controller. ++ * @param qh The QH to init. ++ * ++ * @return 0 if successful, negative error code otherwise. ++ */ ++void dwc_otg_hcd_start_xfer_ddma(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ /* Channel is already assigned */ ++ dwc_hc_t *hc = qh->channel; ++ uint8_t skip_frames = 0; ++ ++ switch (hc->ep_type) { ++ case DWC_OTG_EP_TYPE_CONTROL: ++ case DWC_OTG_EP_TYPE_BULK: ++ init_non_isoc_dma_desc(hcd, qh); ++ ++ dwc_otg_hc_start_transfer_ddma(hcd->core_if, hc); ++ break; ++ case DWC_OTG_EP_TYPE_INTR: ++ init_non_isoc_dma_desc(hcd, qh); ++ ++ update_frame_list(hcd, qh, 1); ++ ++ dwc_otg_hc_start_transfer_ddma(hcd->core_if, hc); ++ break; ++ case DWC_OTG_EP_TYPE_ISOC: ++ ++ if (!qh->ntd) ++ skip_frames = recalc_initial_desc_idx(hcd, qh); ++ ++ init_isoc_dma_desc(hcd, qh, skip_frames); ++ ++ if (!hc->xfer_started) { ++ ++ update_frame_list(hcd, qh, 1); ++ ++ /* ++ * Always set to max, instead of actual size. ++ * Otherwise ntd will be changed with ++ * channel being enabled. Not recommended. ++ * ++ */ ++ hc->ntd = max_desc_num(qh); ++ /* Enable channel only once for ISOC */ ++ dwc_otg_hc_start_transfer_ddma(hcd->core_if, hc); ++ } ++ ++ break; ++ default: ++ ++ break; ++ } ++} ++ ++static void complete_isoc_xfer_ddma(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_halt_status_e halt_status) ++{ ++ struct dwc_otg_hcd_iso_packet_desc *frame_desc; ++ dwc_otg_qtd_t *qtd, *qtd_tmp; ++ dwc_otg_qh_t *qh; ++ dwc_otg_host_dma_desc_t *dma_desc; ++ uint16_t idx, remain; ++ uint8_t urb_compl; ++ ++ qh = hc->qh; ++ idx = qh->td_first; ++ ++ if (hc->halt_status == DWC_OTG_HC_XFER_URB_DEQUEUE) { ++ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp, &hc->qh->qtd_list, qtd_list_entry) ++ qtd->in_process = 0; ++ return; ++ } else if ((halt_status == DWC_OTG_HC_XFER_AHB_ERR) || ++ (halt_status == DWC_OTG_HC_XFER_BABBLE_ERR)) { ++ /* ++ * Channel is halted in these error cases. ++ * Considered as serious issues. ++ * Complete all URBs marking all frames as failed, ++ * irrespective whether some of the descriptors(frames) succeeded or no. ++ * Pass error code to completion routine as well, to ++ * update urb->status, some of class drivers might use it to stop ++ * queing transfer requests. ++ */ ++ int err = (halt_status == DWC_OTG_HC_XFER_AHB_ERR) ++ ? (-DWC_E_IO) ++ : (-DWC_E_OVERFLOW); ++ ++ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp, &hc->qh->qtd_list, qtd_list_entry) { ++ for (idx = 0; idx < qtd->urb->packet_count; idx++) { ++ frame_desc = &qtd->urb->iso_descs[idx]; ++ frame_desc->status = err; ++ } ++ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, err); ++ dwc_otg_hcd_qtd_remove_and_free(hcd, qtd, qh); ++ } ++ return; ++ } ++ ++ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp, &hc->qh->qtd_list, qtd_list_entry) { ++ ++ if (!qtd->in_process) ++ break; ++ ++ urb_compl = 0; ++ ++ do { ++ ++ dma_desc = &qh->desc_list[idx]; ++ ++ frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index]; ++ remain = hc->ep_is_in ? dma_desc->status.b_isoc.n_bytes : 0; ++ ++ if (dma_desc->status.b_isoc.sts == DMA_DESC_STS_PKTERR) { ++ /* ++ * XactError or, unable to complete all the transactions ++ * in the scheduled micro-frame/frame, ++ * both indicated by DMA_DESC_STS_PKTERR. ++ */ ++ qtd->urb->error_count++; ++ frame_desc->actual_length = qh->n_bytes[idx] - remain; ++ frame_desc->status = -DWC_E_PROTOCOL; ++ } else { ++ /* Success */ ++ ++ frame_desc->actual_length = qh->n_bytes[idx] - remain; ++ frame_desc->status = 0; ++ } ++ ++ if (++qtd->isoc_frame_index == qtd->urb->packet_count) { ++ /* ++ * urb->status is not used for isoc transfers here. ++ * The individual frame_desc status are used instead. ++ */ ++ ++ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0); ++ dwc_otg_hcd_qtd_remove_and_free(hcd, qtd, qh); ++ ++ /* ++ * This check is necessary because urb_dequeue can be called ++ * from urb complete callback(sound driver example). ++ * All pending URBs are dequeued there, so no need for ++ * further processing. ++ */ ++ if (hc->halt_status == DWC_OTG_HC_XFER_URB_DEQUEUE) { ++ return; ++ } ++ ++ urb_compl = 1; ++ ++ } ++ ++ qh->ntd--; ++ ++ /* Stop if IOC requested descriptor reached */ ++ if (dma_desc->status.b_isoc.ioc) { ++ idx = desclist_idx_inc(idx, qh->interval, hc->speed); ++ goto stop_scan; ++ } ++ ++ idx = desclist_idx_inc(idx, qh->interval, hc->speed); ++ ++ if (urb_compl) ++ break; ++ } ++ while (idx != qh->td_first); ++ } ++stop_scan: ++ qh->td_first = idx; ++} ++ ++uint8_t update_non_isoc_urb_state_ddma(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_qtd_t * qtd, ++ dwc_otg_host_dma_desc_t * dma_desc, ++ dwc_otg_halt_status_e halt_status, ++ uint32_t n_bytes, uint8_t * xfer_done) ++{ ++ ++ uint16_t remain = hc->ep_is_in ? dma_desc->status.b.n_bytes : 0; ++ dwc_otg_hcd_urb_t *urb = qtd->urb; ++ ++ if (halt_status == DWC_OTG_HC_XFER_AHB_ERR) { ++ urb->status = -DWC_E_IO; ++ return 1; ++ } ++ if (dma_desc->status.b.sts == DMA_DESC_STS_PKTERR) { ++ switch (halt_status) { ++ case DWC_OTG_HC_XFER_STALL: ++ urb->status = -DWC_E_PIPE; ++ break; ++ case DWC_OTG_HC_XFER_BABBLE_ERR: ++ urb->status = -DWC_E_OVERFLOW; ++ break; ++ case DWC_OTG_HC_XFER_XACT_ERR: ++ urb->status = -DWC_E_PROTOCOL; ++ break; ++ default: ++ DWC_ERROR("%s: Unhandled descriptor error status (%d)\n", __func__, ++ halt_status); ++ break; ++ } ++ return 1; ++ } ++ ++ if (dma_desc->status.b.a == 1) { ++ DWC_DEBUGPL(DBG_HCDV, ++ "Active descriptor encountered on channel %d\n", ++ hc->hc_num); ++ return 0; ++ } ++ ++ if (hc->ep_type == DWC_OTG_EP_TYPE_CONTROL) { ++ if (qtd->control_phase == DWC_OTG_CONTROL_DATA) { ++ urb->actual_length += n_bytes - remain; ++ if (remain || urb->actual_length == urb->length) { ++ /* ++ * For Control Data stage do not set urb->status=0 to prevent ++ * URB callback. Set it when Status phase done. See below. ++ */ ++ *xfer_done = 1; ++ } ++ ++ } else if (qtd->control_phase == DWC_OTG_CONTROL_STATUS) { ++ urb->status = 0; ++ *xfer_done = 1; ++ } ++ /* No handling for SETUP stage */ ++ } else { ++ /* BULK and INTR */ ++ urb->actual_length += n_bytes - remain; ++ if (remain || urb->actual_length == urb->length) { ++ urb->status = 0; ++ *xfer_done = 1; ++ } ++ } ++ ++ return 0; ++} ++ ++static void complete_non_isoc_xfer_ddma(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_halt_status_e halt_status) ++{ ++ dwc_otg_hcd_urb_t *urb = NULL; ++ dwc_otg_qtd_t *qtd, *qtd_tmp; ++ dwc_otg_qh_t *qh; ++ dwc_otg_host_dma_desc_t *dma_desc; ++ uint32_t n_bytes, n_desc, i; ++ uint8_t failed = 0, xfer_done; ++ ++ n_desc = 0; ++ ++ qh = hc->qh; ++ ++ if (hc->halt_status == DWC_OTG_HC_XFER_URB_DEQUEUE) { ++ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp, &hc->qh->qtd_list, qtd_list_entry) { ++ qtd->in_process = 0; ++ } ++ return; ++ } ++ ++ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp, &qh->qtd_list, qtd_list_entry) { ++ ++ urb = qtd->urb; ++ ++ n_bytes = 0; ++ xfer_done = 0; ++ ++ for (i = 0; i < qtd->n_desc; i++) { ++ dma_desc = &qh->desc_list[n_desc]; ++ ++ n_bytes = qh->n_bytes[n_desc]; ++ ++ failed = ++ update_non_isoc_urb_state_ddma(hcd, hc, qtd, ++ dma_desc, ++ halt_status, n_bytes, ++ &xfer_done); ++ ++ if (failed ++ || (xfer_done ++ && (urb->status != -DWC_E_IN_PROGRESS))) { ++ ++ hcd->fops->complete(hcd, urb->priv, urb, ++ urb->status); ++ dwc_otg_hcd_qtd_remove_and_free(hcd, qtd, qh); ++ ++ if (failed) ++ goto stop_scan; ++ } else if (qh->ep_type == UE_CONTROL) { ++ if (qtd->control_phase == DWC_OTG_CONTROL_SETUP) { ++ if (urb->length > 0) { ++ qtd->control_phase = DWC_OTG_CONTROL_DATA; ++ } else { ++ qtd->control_phase = DWC_OTG_CONTROL_STATUS; ++ } ++ DWC_DEBUGPL(DBG_HCDV, " Control setup transaction done\n"); ++ } else if (qtd->control_phase == DWC_OTG_CONTROL_DATA) { ++ if (xfer_done) { ++ qtd->control_phase = DWC_OTG_CONTROL_STATUS; ++ DWC_DEBUGPL(DBG_HCDV, " Control data transfer done\n"); ++ } else if (i + 1 == qtd->n_desc) { ++ /* ++ * Last descriptor for Control data stage which is ++ * not completed yet. ++ */ ++ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd); ++ } ++ } ++ } ++ ++ n_desc++; ++ } ++ ++ } ++ ++stop_scan: ++ ++ if (qh->ep_type != UE_CONTROL) { ++ /* ++ * Resetting the data toggle for bulk ++ * and interrupt endpoints in case of stall. See handle_hc_stall_intr() ++ */ ++ if (halt_status == DWC_OTG_HC_XFER_STALL) ++ qh->data_toggle = DWC_OTG_HC_PID_DATA0; ++ else ++ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd); ++ } ++ ++ if (halt_status == DWC_OTG_HC_XFER_COMPLETE) { ++ hcint_data_t hcint; ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ if (hcint.b.nyet) { ++ /* ++ * Got a NYET on the last transaction of the transfer. It ++ * means that the endpoint should be in the PING state at the ++ * beginning of the next transfer. ++ */ ++ qh->ping_state = 1; ++ clear_hc_int(hc_regs, nyet); ++ } ++ ++ } ++ ++} ++ ++/** ++ * This function is called from interrupt handlers. ++ * Scans the descriptor list, updates URB's status and ++ * calls completion routine for the URB if it's done. ++ * Releases the channel to be used by other transfers. ++ * In case of Isochronous endpoint the channel is not halted until ++ * the end of the session, i.e. QTD list is empty. ++ * If periodic channel released the FrameList is updated accordingly. ++ * ++ * Calls transaction selection routines to activate pending transfers. ++ * ++ * @param hcd The HCD state structure for the DWC OTG controller. ++ * @param hc Host channel, the transfer is completed on. ++ * @param hc_regs Host channel registers. ++ * @param halt_status Reason the channel is being halted, ++ * or just XferComplete for isochronous transfer ++ */ ++void dwc_otg_hcd_complete_xfer_ddma(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_halt_status_e halt_status) ++{ ++ uint8_t continue_isoc_xfer = 0; ++ dwc_otg_transaction_type_e tr_type; ++ dwc_otg_qh_t *qh = hc->qh; ++ ++ if (hc->ep_type == DWC_OTG_EP_TYPE_ISOC) { ++ ++ complete_isoc_xfer_ddma(hcd, hc, hc_regs, halt_status); ++ ++ /* Release the channel if halted or session completed */ ++ if (halt_status != DWC_OTG_HC_XFER_COMPLETE || ++ DWC_CIRCLEQ_EMPTY(&qh->qtd_list)) { ++ ++ /* Halt the channel if session completed */ ++ if (halt_status == DWC_OTG_HC_XFER_COMPLETE) { ++ dwc_otg_hc_halt(hcd->core_if, hc, halt_status); ++ } ++ ++ release_channel_ddma(hcd, qh); ++ dwc_otg_hcd_qh_remove(hcd, qh); ++ } else { ++ /* Keep in assigned schedule to continue transfer */ ++ DWC_LIST_MOVE_HEAD(&hcd->periodic_sched_assigned, ++ &qh->qh_list_entry); ++ continue_isoc_xfer = 1; ++ ++ } ++ /** @todo Consider the case when period exceeds FrameList size. ++ * Frame Rollover interrupt should be used. ++ */ ++ } else { ++ /* Scan descriptor list to complete the URB(s), then release the channel */ ++ complete_non_isoc_xfer_ddma(hcd, hc, hc_regs, halt_status); ++ ++ release_channel_ddma(hcd, qh); ++ dwc_otg_hcd_qh_remove(hcd, qh); ++ ++ if (!DWC_CIRCLEQ_EMPTY(&qh->qtd_list)) { ++ /* Add back to inactive non-periodic schedule on normal completion */ ++ dwc_otg_hcd_qh_add(hcd, qh); ++ } ++ ++ } ++ tr_type = dwc_otg_hcd_select_transactions(hcd); ++ if (tr_type != DWC_OTG_TRANSACTION_NONE || continue_isoc_xfer) { ++ if (continue_isoc_xfer) { ++ if (tr_type == DWC_OTG_TRANSACTION_NONE) { ++ tr_type = DWC_OTG_TRANSACTION_PERIODIC; ++ } else if (tr_type == DWC_OTG_TRANSACTION_NON_PERIODIC) { ++ tr_type = DWC_OTG_TRANSACTION_ALL; ++ } ++ } ++ dwc_otg_hcd_queue_transactions(hcd, tr_type); ++ } ++} ++ ++#endif /* DWC_DEVICE_ONLY */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd_if.h +@@ -0,0 +1,421 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd_if.h $ ++ * $Revision: #12 $ ++ * $Date: 2011/10/26 $ ++ * $Change: 1873028 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++#ifndef DWC_DEVICE_ONLY ++#ifndef __DWC_HCD_IF_H__ ++#define __DWC_HCD_IF_H__ ++ ++#include "dwc_otg_core_if.h" ++ ++/** @file ++ * This file defines DWC_OTG HCD Core API. ++ */ ++ ++struct dwc_otg_hcd; ++typedef struct dwc_otg_hcd dwc_otg_hcd_t; ++ ++struct dwc_otg_hcd_urb; ++typedef struct dwc_otg_hcd_urb dwc_otg_hcd_urb_t; ++ ++/** @name HCD Function Driver Callbacks */ ++/** @{ */ ++ ++/** This function is called whenever core switches to host mode. */ ++typedef int (*dwc_otg_hcd_start_cb_t) (dwc_otg_hcd_t * hcd); ++ ++/** This function is called when device has been disconnected */ ++typedef int (*dwc_otg_hcd_disconnect_cb_t) (dwc_otg_hcd_t * hcd); ++ ++/** Wrapper provides this function to HCD to core, so it can get hub information to which device is connected */ ++typedef int (*dwc_otg_hcd_hub_info_from_urb_cb_t) (dwc_otg_hcd_t * hcd, ++ void *urb_handle, ++ uint32_t * hub_addr, ++ uint32_t * port_addr); ++/** Via this function HCD core gets device speed */ ++typedef int (*dwc_otg_hcd_speed_from_urb_cb_t) (dwc_otg_hcd_t * hcd, ++ void *urb_handle); ++ ++/** This function is called when urb is completed */ ++typedef int (*dwc_otg_hcd_complete_urb_cb_t) (dwc_otg_hcd_t * hcd, ++ void *urb_handle, ++ dwc_otg_hcd_urb_t * dwc_otg_urb, ++ int32_t status); ++ ++/** Via this function HCD core gets b_hnp_enable parameter */ ++typedef int (*dwc_otg_hcd_get_b_hnp_enable) (dwc_otg_hcd_t * hcd); ++ ++struct dwc_otg_hcd_function_ops { ++ dwc_otg_hcd_start_cb_t start; ++ dwc_otg_hcd_disconnect_cb_t disconnect; ++ dwc_otg_hcd_hub_info_from_urb_cb_t hub_info; ++ dwc_otg_hcd_speed_from_urb_cb_t speed; ++ dwc_otg_hcd_complete_urb_cb_t complete; ++ dwc_otg_hcd_get_b_hnp_enable get_b_hnp_enable; ++}; ++/** @} */ ++ ++/** @name HCD Core API */ ++/** @{ */ ++/** This function allocates dwc_otg_hcd structure and returns pointer on it. */ ++extern dwc_otg_hcd_t *dwc_otg_hcd_alloc_hcd(void); ++ ++/** This function should be called to initiate HCD Core. ++ * ++ * @param hcd The HCD ++ * @param core_if The DWC_OTG Core ++ * ++ * Returns -DWC_E_NO_MEMORY if no enough memory. ++ * Returns 0 on success ++ */ ++extern int dwc_otg_hcd_init(dwc_otg_hcd_t * hcd, dwc_otg_core_if_t * core_if); ++ ++/** Frees HCD ++ * ++ * @param hcd The HCD ++ */ ++extern void dwc_otg_hcd_remove(dwc_otg_hcd_t * hcd); ++ ++/** This function should be called on every hardware interrupt. ++ * ++ * @param dwc_otg_hcd The HCD ++ * ++ * Returns non zero if interrupt is handled ++ * Return 0 if interrupt is not handled ++ */ ++extern int32_t dwc_otg_hcd_handle_intr(dwc_otg_hcd_t * dwc_otg_hcd); ++ ++/** This function is used to handle the fast interrupt ++ * ++ */ ++#ifdef CONFIG_ARM64 ++extern void dwc_otg_hcd_handle_fiq(void); ++#else ++extern void __attribute__ ((naked)) dwc_otg_hcd_handle_fiq(void); ++#endif ++ ++/** ++ * Returns private data set by ++ * dwc_otg_hcd_set_priv_data function. ++ * ++ * @param hcd The HCD ++ */ ++extern void *dwc_otg_hcd_get_priv_data(dwc_otg_hcd_t * hcd); ++ ++/** ++ * Set private data. ++ * ++ * @param hcd The HCD ++ * @param priv_data pointer to be stored in private data ++ */ ++extern void dwc_otg_hcd_set_priv_data(dwc_otg_hcd_t * hcd, void *priv_data); ++ ++/** ++ * This function initializes the HCD Core. ++ * ++ * @param hcd The HCD ++ * @param fops The Function Driver Operations data structure containing pointers to all callbacks. ++ * ++ * Returns -DWC_E_NO_DEVICE if Core is currently is in device mode. ++ * Returns 0 on success ++ */ ++extern int dwc_otg_hcd_start(dwc_otg_hcd_t * hcd, ++ struct dwc_otg_hcd_function_ops *fops); ++ ++/** ++ * Halts the DWC_otg host mode operations in a clean manner. USB transfers are ++ * stopped. ++ * ++ * @param hcd The HCD ++ */ ++extern void dwc_otg_hcd_stop(dwc_otg_hcd_t * hcd); ++ ++/** ++ * Handles hub class-specific requests. ++ * ++ * @param dwc_otg_hcd The HCD ++ * @param typeReq Request Type ++ * @param wValue wValue from control request ++ * @param wIndex wIndex from control request ++ * @param buf data buffer ++ * @param wLength data buffer length ++ * ++ * Returns -DWC_E_INVALID if invalid argument is passed ++ * Returns 0 on success ++ */ ++extern int dwc_otg_hcd_hub_control(dwc_otg_hcd_t * dwc_otg_hcd, ++ uint16_t typeReq, uint16_t wValue, ++ uint16_t wIndex, uint8_t * buf, ++ uint16_t wLength); ++ ++/** ++ * Returns otg port number. ++ * ++ * @param hcd The HCD ++ */ ++extern uint32_t dwc_otg_hcd_otg_port(dwc_otg_hcd_t * hcd); ++ ++/** ++ * Returns OTG version - either 1.3 or 2.0. ++ * ++ * @param core_if The core_if structure pointer ++ */ ++extern uint16_t dwc_otg_get_otg_version(dwc_otg_core_if_t * core_if); ++ ++/** ++ * Returns 1 if currently core is acting as B host, and 0 otherwise. ++ * ++ * @param hcd The HCD ++ */ ++extern uint32_t dwc_otg_hcd_is_b_host(dwc_otg_hcd_t * hcd); ++ ++/** ++ * Returns current frame number. ++ * ++ * @param hcd The HCD ++ */ ++extern int dwc_otg_hcd_get_frame_number(dwc_otg_hcd_t * hcd); ++ ++/** ++ * Dumps hcd state. ++ * ++ * @param hcd The HCD ++ */ ++extern void dwc_otg_hcd_dump_state(dwc_otg_hcd_t * hcd); ++ ++/** ++ * Dump the average frame remaining at SOF. This can be used to ++ * determine average interrupt latency. Frame remaining is also shown for ++ * start transfer and two additional sample points. ++ * Currently this function is not implemented. ++ * ++ * @param hcd The HCD ++ */ ++extern void dwc_otg_hcd_dump_frrem(dwc_otg_hcd_t * hcd); ++ ++/** ++ * Sends LPM transaction to the local device. ++ * ++ * @param hcd The HCD ++ * @param devaddr Device Address ++ * @param hird Host initiated resume duration ++ * @param bRemoteWake Value of bRemoteWake field in LPM transaction ++ * ++ * Returns negative value if sending LPM transaction was not succeeded. ++ * Returns 0 on success. ++ */ ++extern int dwc_otg_hcd_send_lpm(dwc_otg_hcd_t * hcd, uint8_t devaddr, ++ uint8_t hird, uint8_t bRemoteWake); ++ ++/* URB interface */ ++ ++/** ++ * Allocates memory for dwc_otg_hcd_urb structure. ++ * Allocated memory should be freed by call of DWC_FREE. ++ * ++ * @param hcd The HCD ++ * @param iso_desc_count Count of ISOC descriptors ++ * @param atomic_alloc Specefies whether to perform atomic allocation. ++ */ ++extern dwc_otg_hcd_urb_t *dwc_otg_hcd_urb_alloc(dwc_otg_hcd_t * hcd, ++ int iso_desc_count, ++ int atomic_alloc); ++ ++/** ++ * Set pipe information in URB. ++ * ++ * @param hcd_urb DWC_OTG URB ++ * @param devaddr Device Address ++ * @param ep_num Endpoint Number ++ * @param ep_type Endpoint Type ++ * @param ep_dir Endpoint Direction ++ * @param mps Max Packet Size ++ */ ++extern void dwc_otg_hcd_urb_set_pipeinfo(dwc_otg_hcd_urb_t * hcd_urb, ++ uint8_t devaddr, uint8_t ep_num, ++ uint8_t ep_type, uint8_t ep_dir, ++ uint16_t mps); ++ ++/* Transfer flags */ ++#define URB_GIVEBACK_ASAP 0x1 ++#define URB_SEND_ZERO_PACKET 0x2 ++ ++/** ++ * Sets dwc_otg_hcd_urb parameters. ++ * ++ * @param urb DWC_OTG URB allocated by dwc_otg_hcd_urb_alloc function. ++ * @param urb_handle Unique handle for request, this will be passed back ++ * to function driver in completion callback. ++ * @param buf The buffer for the data ++ * @param dma The DMA buffer for the data ++ * @param buflen Transfer length ++ * @param sp Buffer for setup data ++ * @param sp_dma DMA address of setup data buffer ++ * @param flags Transfer flags ++ * @param interval Polling interval for interrupt or isochronous transfers. ++ */ ++extern void dwc_otg_hcd_urb_set_params(dwc_otg_hcd_urb_t * urb, ++ void *urb_handle, void *buf, ++ dwc_dma_t dma, uint32_t buflen, void *sp, ++ dwc_dma_t sp_dma, uint32_t flags, ++ uint16_t interval); ++ ++/** Gets status from dwc_otg_hcd_urb ++ * ++ * @param dwc_otg_urb DWC_OTG URB ++ */ ++extern uint32_t dwc_otg_hcd_urb_get_status(dwc_otg_hcd_urb_t * dwc_otg_urb); ++ ++/** Gets actual length from dwc_otg_hcd_urb ++ * ++ * @param dwc_otg_urb DWC_OTG URB ++ */ ++extern uint32_t dwc_otg_hcd_urb_get_actual_length(dwc_otg_hcd_urb_t * ++ dwc_otg_urb); ++ ++/** Gets error count from dwc_otg_hcd_urb. Only for ISOC URBs ++ * ++ * @param dwc_otg_urb DWC_OTG URB ++ */ ++extern uint32_t dwc_otg_hcd_urb_get_error_count(dwc_otg_hcd_urb_t * ++ dwc_otg_urb); ++ ++/** Set ISOC descriptor offset and length ++ * ++ * @param dwc_otg_urb DWC_OTG URB ++ * @param desc_num ISOC descriptor number ++ * @param offset Offset from beginig of buffer. ++ * @param length Transaction length ++ */ ++extern void dwc_otg_hcd_urb_set_iso_desc_params(dwc_otg_hcd_urb_t * dwc_otg_urb, ++ int desc_num, uint32_t offset, ++ uint32_t length); ++ ++/** Get status of ISOC descriptor, specified by desc_num ++ * ++ * @param dwc_otg_urb DWC_OTG URB ++ * @param desc_num ISOC descriptor number ++ */ ++extern uint32_t dwc_otg_hcd_urb_get_iso_desc_status(dwc_otg_hcd_urb_t * ++ dwc_otg_urb, int desc_num); ++ ++/** Get actual length of ISOC descriptor, specified by desc_num ++ * ++ * @param dwc_otg_urb DWC_OTG URB ++ * @param desc_num ISOC descriptor number ++ */ ++extern uint32_t dwc_otg_hcd_urb_get_iso_desc_actual_length(dwc_otg_hcd_urb_t * ++ dwc_otg_urb, ++ int desc_num); ++ ++/** Queue URB. After transfer is completes, the complete callback will be called with the URB status ++ * ++ * @param dwc_otg_hcd The HCD ++ * @param dwc_otg_urb DWC_OTG URB ++ * @param ep_handle Out parameter for returning endpoint handle ++ * @param atomic_alloc Flag to do atomic allocation if needed ++ * ++ * Returns -DWC_E_NO_DEVICE if no device is connected. ++ * Returns -DWC_E_NO_MEMORY if there is no enough memory. ++ * Returns 0 on success. ++ */ ++extern int dwc_otg_hcd_urb_enqueue(dwc_otg_hcd_t * dwc_otg_hcd, ++ dwc_otg_hcd_urb_t * dwc_otg_urb, ++ void **ep_handle, int atomic_alloc); ++ ++/** De-queue the specified URB ++ * ++ * @param dwc_otg_hcd The HCD ++ * @param dwc_otg_urb DWC_OTG URB ++ */ ++extern int dwc_otg_hcd_urb_dequeue(dwc_otg_hcd_t * dwc_otg_hcd, ++ dwc_otg_hcd_urb_t * dwc_otg_urb); ++ ++/** Frees resources in the DWC_otg controller related to a given endpoint. ++ * Any URBs for the endpoint must already be dequeued. ++ * ++ * @param hcd The HCD ++ * @param ep_handle Endpoint handle, returned by dwc_otg_hcd_urb_enqueue function ++ * @param retry Number of retries if there are queued transfers. ++ * ++ * Returns -DWC_E_INVALID if invalid arguments are passed. ++ * Returns 0 on success ++ */ ++extern int dwc_otg_hcd_endpoint_disable(dwc_otg_hcd_t * hcd, void *ep_handle, ++ int retry); ++ ++/* Resets the data toggle in qh structure. This function can be called from ++ * usb_clear_halt routine. ++ * ++ * @param hcd The HCD ++ * @param ep_handle Endpoint handle, returned by dwc_otg_hcd_urb_enqueue function ++ * ++ * Returns -DWC_E_INVALID if invalid arguments are passed. ++ * Returns 0 on success ++ */ ++extern int dwc_otg_hcd_endpoint_reset(dwc_otg_hcd_t * hcd, void *ep_handle); ++ ++/** Returns 1 if status of specified port is changed and 0 otherwise. ++ * ++ * @param hcd The HCD ++ * @param port Port number ++ */ ++extern int dwc_otg_hcd_is_status_changed(dwc_otg_hcd_t * hcd, int port); ++ ++/** Call this function to check if bandwidth was allocated for specified endpoint. ++ * Only for ISOC and INTERRUPT endpoints. ++ * ++ * @param hcd The HCD ++ * @param ep_handle Endpoint handle ++ */ ++extern int dwc_otg_hcd_is_bandwidth_allocated(dwc_otg_hcd_t * hcd, ++ void *ep_handle); ++ ++/** Call this function to check if bandwidth was freed for specified endpoint. ++ * ++ * @param hcd The HCD ++ * @param ep_handle Endpoint handle ++ */ ++extern int dwc_otg_hcd_is_bandwidth_freed(dwc_otg_hcd_t * hcd, void *ep_handle); ++ ++/** Returns bandwidth allocated for specified endpoint in microseconds. ++ * Only for ISOC and INTERRUPT endpoints. ++ * ++ * @param hcd The HCD ++ * @param ep_handle Endpoint handle ++ */ ++extern uint8_t dwc_otg_hcd_get_ep_bandwidth(dwc_otg_hcd_t * hcd, ++ void *ep_handle); ++ ++/** @} */ ++ ++#endif /* __DWC_HCD_IF_H__ */ ++#endif /* DWC_DEVICE_ONLY */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd_intr.c +@@ -0,0 +1,2757 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd_intr.c $ ++ * $Revision: #89 $ ++ * $Date: 2011/10/20 $ ++ * $Change: 1869487 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++#ifndef DWC_DEVICE_ONLY ++ ++#include "dwc_otg_hcd.h" ++#include "dwc_otg_regs.h" ++ ++#include ++#ifdef CONFIG_ARM ++#include ++#endif ++ ++extern bool microframe_schedule; ++ ++/** @file ++ * This file contains the implementation of the HCD Interrupt handlers. ++ */ ++ ++int fiq_done, int_done; ++ ++#ifdef FIQ_DEBUG ++char buffer[1000*16]; ++int wptr; ++void notrace _fiq_print(FIQDBG_T dbg_lvl, char *fmt, ...) ++{ ++ FIQDBG_T dbg_lvl_req = FIQDBG_PORTHUB; ++ va_list args; ++ char text[17]; ++ hfnum_data_t hfnum = { .d32 = FIQ_READ(dwc_regs_base + 0x408) }; ++ ++ if(dbg_lvl & dbg_lvl_req || dbg_lvl == FIQDBG_ERR) ++ { ++ local_fiq_disable(); ++ snprintf(text, 9, "%4d%d:%d ", hfnum.b.frnum/8, hfnum.b.frnum%8, 8 - hfnum.b.frrem/937); ++ va_start(args, fmt); ++ vsnprintf(text+8, 9, fmt, args); ++ va_end(args); ++ ++ memcpy(buffer + wptr, text, 16); ++ wptr = (wptr + 16) % sizeof(buffer); ++ local_fiq_enable(); ++ } ++} ++#endif ++ ++/** This function handles interrupts for the HCD. */ ++int32_t dwc_otg_hcd_handle_intr(dwc_otg_hcd_t * dwc_otg_hcd) ++{ ++ int retval = 0; ++ static int last_time; ++ dwc_otg_core_if_t *core_if = dwc_otg_hcd->core_if; ++ gintsts_data_t gintsts; ++ gintmsk_data_t gintmsk; ++ hfnum_data_t hfnum; ++ haintmsk_data_t haintmsk; ++ ++#ifdef DEBUG ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ ++#endif ++ ++ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts); ++ gintmsk.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintmsk); ++ ++ /* Exit from ISR if core is hibernated */ ++ if (core_if->hibernation_suspend == 1) { ++ goto exit_handler_routine; ++ } ++ DWC_SPINLOCK(dwc_otg_hcd->lock); ++ /* Check if HOST Mode */ ++ if (dwc_otg_is_host_mode(core_if)) { ++ if (fiq_enable) { ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&dwc_otg_hcd->fiq_state->lock); ++ /* Pull in from the FIQ's disabled mask */ ++ gintmsk.d32 = gintmsk.d32 | ~(dwc_otg_hcd->fiq_state->gintmsk_saved.d32); ++ dwc_otg_hcd->fiq_state->gintmsk_saved.d32 = ~0; ++ } ++ ++ if (fiq_fsm_enable && ( 0x0000FFFF & ~(dwc_otg_hcd->fiq_state->haintmsk_saved.b2.chint))) { ++ gintsts.b.hcintr = 1; ++ } ++ ++ /* Danger will robinson: fake a SOF if necessary */ ++ if (fiq_fsm_enable && (dwc_otg_hcd->fiq_state->gintmsk_saved.b.sofintr == 1)) { ++ gintsts.b.sofintr = 1; ++ } ++ gintsts.d32 &= gintmsk.d32; ++ ++ if (fiq_enable) { ++ fiq_fsm_spin_unlock(&dwc_otg_hcd->fiq_state->lock); ++ local_fiq_enable(); ++ } ++ ++ if (!gintsts.d32) { ++ goto exit_handler_routine; ++ } ++ ++#ifdef DEBUG ++ // We should be OK doing this because the common interrupts should already have been serviced ++ /* Don't print debug message in the interrupt handler on SOF */ ++#ifndef DEBUG_SOF ++ if (gintsts.d32 != DWC_SOF_INTR_MASK) ++#endif ++ DWC_DEBUGPL(DBG_HCDI, "\n"); ++#endif ++ ++#ifdef DEBUG ++#ifndef DEBUG_SOF ++ if (gintsts.d32 != DWC_SOF_INTR_MASK) ++#endif ++ DWC_DEBUGPL(DBG_HCDI, ++ "DWC OTG HCD Interrupt Detected gintsts&gintmsk=0x%08x core_if=%p\n", ++ gintsts.d32, core_if); ++#endif ++ hfnum.d32 = DWC_READ_REG32(&dwc_otg_hcd->core_if->host_if->host_global_regs->hfnum); ++ if (gintsts.b.sofintr) { ++ retval |= dwc_otg_hcd_handle_sof_intr(dwc_otg_hcd); ++ } ++ ++ if (gintsts.b.rxstsqlvl) { ++ retval |= ++ dwc_otg_hcd_handle_rx_status_q_level_intr ++ (dwc_otg_hcd); ++ } ++ if (gintsts.b.nptxfempty) { ++ retval |= ++ dwc_otg_hcd_handle_np_tx_fifo_empty_intr ++ (dwc_otg_hcd); ++ } ++ if (gintsts.b.i2cintr) { ++ /** @todo Implement i2cintr handler. */ ++ } ++ if (gintsts.b.portintr) { ++ ++ gintmsk_data_t gintmsk = { .b.portintr = 1}; ++ retval |= dwc_otg_hcd_handle_port_intr(dwc_otg_hcd); ++ if (fiq_enable) { ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&dwc_otg_hcd->fiq_state->lock); ++ DWC_MODIFY_REG32(&dwc_otg_hcd->core_if->core_global_regs->gintmsk, 0, gintmsk.d32); ++ fiq_fsm_spin_unlock(&dwc_otg_hcd->fiq_state->lock); ++ local_fiq_enable(); ++ } else { ++ DWC_MODIFY_REG32(&dwc_otg_hcd->core_if->core_global_regs->gintmsk, 0, gintmsk.d32); ++ } ++ } ++ if (gintsts.b.hcintr) { ++ retval |= dwc_otg_hcd_handle_hc_intr(dwc_otg_hcd); ++ } ++ if (gintsts.b.ptxfempty) { ++ retval |= ++ dwc_otg_hcd_handle_perio_tx_fifo_empty_intr ++ (dwc_otg_hcd); ++ } ++#ifdef DEBUG ++#ifndef DEBUG_SOF ++ if (gintsts.d32 != DWC_SOF_INTR_MASK) ++#endif ++ { ++ DWC_DEBUGPL(DBG_HCDI, ++ "DWC OTG HCD Finished Servicing Interrupts\n"); ++ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD gintsts=0x%08x\n", ++ DWC_READ_REG32(&global_regs->gintsts)); ++ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD gintmsk=0x%08x\n", ++ DWC_READ_REG32(&global_regs->gintmsk)); ++ } ++#endif ++ ++#ifdef DEBUG ++#ifndef DEBUG_SOF ++ if (gintsts.d32 != DWC_SOF_INTR_MASK) ++#endif ++ DWC_DEBUGPL(DBG_HCDI, "\n"); ++#endif ++ ++ } ++ ++exit_handler_routine: ++ if (fiq_enable) { ++ gintmsk_data_t gintmsk_new; ++ haintmsk_data_t haintmsk_new; ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&dwc_otg_hcd->fiq_state->lock); ++ gintmsk_new.d32 = *(volatile uint32_t *)&dwc_otg_hcd->fiq_state->gintmsk_saved.d32; ++ if(fiq_fsm_enable) ++ haintmsk_new.d32 = *(volatile uint32_t *)&dwc_otg_hcd->fiq_state->haintmsk_saved.d32; ++ else ++ haintmsk_new.d32 = 0x0000FFFF; ++ ++ /* The FIQ could have sneaked another interrupt in. If so, don't clear MPHI */ ++ if ((gintmsk_new.d32 == ~0) && (haintmsk_new.d32 == 0x0000FFFF)) { ++ if (dwc_otg_hcd->fiq_state->mphi_regs.swirq_clr) { ++ DWC_WRITE_REG32(dwc_otg_hcd->fiq_state->mphi_regs.swirq_clr, 1); ++ } else { ++ DWC_WRITE_REG32(dwc_otg_hcd->fiq_state->mphi_regs.intstat, (1<<16)); ++ } ++ if (dwc_otg_hcd->fiq_state->mphi_int_count >= 50) { ++ fiq_print(FIQDBG_INT, dwc_otg_hcd->fiq_state, "MPHI CLR"); ++ DWC_WRITE_REG32(dwc_otg_hcd->fiq_state->mphi_regs.ctrl, ((1<<31) + (1<<16))); ++ while (!(DWC_READ_REG32(dwc_otg_hcd->fiq_state->mphi_regs.ctrl) & (1 << 17))) ++ ; ++ DWC_WRITE_REG32(dwc_otg_hcd->fiq_state->mphi_regs.ctrl, (1<<31)); ++ dwc_otg_hcd->fiq_state->mphi_int_count = 0; ++ } ++ int_done++; ++ } ++ haintmsk.d32 = DWC_READ_REG32(&core_if->host_if->host_global_regs->haintmsk); ++ /* Re-enable interrupts that the FIQ masked (first time round) */ ++ FIQ_WRITE(dwc_otg_hcd->fiq_state->dwc_regs_base + GINTMSK, gintmsk.d32); ++ fiq_fsm_spin_unlock(&dwc_otg_hcd->fiq_state->lock); ++ local_fiq_enable(); ++ ++ if ((jiffies / HZ) > last_time) { ++ //dwc_otg_qh_t *qh; ++ //dwc_list_link_t *cur; ++ /* Once a second output the fiq and irq numbers, useful for debug */ ++ last_time = jiffies / HZ; ++ // DWC_WARN("np_kick=%d AHC=%d sched_frame=%d cur_frame=%d int_done=%d fiq_done=%d", ++ // dwc_otg_hcd->fiq_state->kick_np_queues, dwc_otg_hcd->available_host_channels, ++ // dwc_otg_hcd->fiq_state->next_sched_frame, hfnum.b.frnum, int_done, dwc_otg_hcd->fiq_state->fiq_done); ++ //printk(KERN_WARNING "Periodic queues:\n"); ++ } ++ } ++ ++ DWC_SPINUNLOCK(dwc_otg_hcd->lock); ++ return retval; ++} ++ ++#ifdef DWC_TRACK_MISSED_SOFS ++ ++#warning Compiling code to track missed SOFs ++#define FRAME_NUM_ARRAY_SIZE 1000 ++/** ++ * This function is for debug only. ++ */ ++static inline void track_missed_sofs(uint16_t curr_frame_number) ++{ ++ static uint16_t frame_num_array[FRAME_NUM_ARRAY_SIZE]; ++ static uint16_t last_frame_num_array[FRAME_NUM_ARRAY_SIZE]; ++ static int frame_num_idx = 0; ++ static uint16_t last_frame_num = DWC_HFNUM_MAX_FRNUM; ++ static int dumped_frame_num_array = 0; ++ ++ if (frame_num_idx < FRAME_NUM_ARRAY_SIZE) { ++ if (((last_frame_num + 1) & DWC_HFNUM_MAX_FRNUM) != ++ curr_frame_number) { ++ frame_num_array[frame_num_idx] = curr_frame_number; ++ last_frame_num_array[frame_num_idx++] = last_frame_num; ++ } ++ } else if (!dumped_frame_num_array) { ++ int i; ++ DWC_PRINTF("Frame Last Frame\n"); ++ DWC_PRINTF("----- ----------\n"); ++ for (i = 0; i < FRAME_NUM_ARRAY_SIZE; i++) { ++ DWC_PRINTF("0x%04x 0x%04x\n", ++ frame_num_array[i], last_frame_num_array[i]); ++ } ++ dumped_frame_num_array = 1; ++ } ++ last_frame_num = curr_frame_number; ++} ++#endif ++ ++/** ++ * Handles the start-of-frame interrupt in host mode. Non-periodic ++ * transactions may be queued to the DWC_otg controller for the current ++ * (micro)frame. Periodic transactions may be queued to the controller for the ++ * next (micro)frame. ++ */ ++int32_t dwc_otg_hcd_handle_sof_intr(dwc_otg_hcd_t * hcd) ++{ ++ hfnum_data_t hfnum; ++ gintsts_data_t gintsts = { .d32 = 0 }; ++ dwc_list_link_t *qh_entry; ++ dwc_otg_qh_t *qh; ++ dwc_otg_transaction_type_e tr_type; ++ int did_something = 0; ++ int32_t next_sched_frame = -1; ++ ++ hfnum.d32 = ++ DWC_READ_REG32(&hcd->core_if->host_if->host_global_regs->hfnum); ++ ++#ifdef DEBUG_SOF ++ DWC_DEBUGPL(DBG_HCD, "--Start of Frame Interrupt--\n"); ++#endif ++ hcd->frame_number = hfnum.b.frnum; ++ ++#ifdef DEBUG ++ hcd->frrem_accum += hfnum.b.frrem; ++ hcd->frrem_samples++; ++#endif ++ ++#ifdef DWC_TRACK_MISSED_SOFS ++ track_missed_sofs(hcd->frame_number); ++#endif ++ /* Determine whether any periodic QHs should be executed. */ ++ qh_entry = DWC_LIST_FIRST(&hcd->periodic_sched_inactive); ++ while (qh_entry != &hcd->periodic_sched_inactive) { ++ qh = DWC_LIST_ENTRY(qh_entry, dwc_otg_qh_t, qh_list_entry); ++ qh_entry = qh_entry->next; ++ if (dwc_frame_num_le(qh->sched_frame, hcd->frame_number)) { ++ ++ /* ++ * Move QH to the ready list to be executed next ++ * (micro)frame. ++ */ ++ DWC_LIST_MOVE_HEAD(&hcd->periodic_sched_ready, ++ &qh->qh_list_entry); ++ ++ did_something = 1; ++ } ++ else ++ { ++ if(next_sched_frame < 0 || dwc_frame_num_le(qh->sched_frame, next_sched_frame)) ++ { ++ next_sched_frame = qh->sched_frame; ++ } ++ } ++ } ++ if (fiq_enable) ++ hcd->fiq_state->next_sched_frame = next_sched_frame; ++ ++ tr_type = dwc_otg_hcd_select_transactions(hcd); ++ if (tr_type != DWC_OTG_TRANSACTION_NONE) { ++ dwc_otg_hcd_queue_transactions(hcd, tr_type); ++ did_something = 1; ++ } ++ ++ /* Clear interrupt - but do not trample on the FIQ sof */ ++ if (!fiq_fsm_enable) { ++ gintsts.b.sofintr = 1; ++ DWC_WRITE_REG32(&hcd->core_if->core_global_regs->gintsts, gintsts.d32); ++ } ++ return 1; ++} ++ ++/** Handles the Rx Status Queue Level Interrupt, which indicates that there is at ++ * least one packet in the Rx FIFO. The packets are moved from the FIFO to ++ * memory if the DWC_otg controller is operating in Slave mode. */ ++int32_t dwc_otg_hcd_handle_rx_status_q_level_intr(dwc_otg_hcd_t * dwc_otg_hcd) ++{ ++ host_grxsts_data_t grxsts; ++ dwc_hc_t *hc = NULL; ++ ++ DWC_DEBUGPL(DBG_HCD, "--RxStsQ Level Interrupt--\n"); ++ ++ grxsts.d32 = ++ DWC_READ_REG32(&dwc_otg_hcd->core_if->core_global_regs->grxstsp); ++ ++ hc = dwc_otg_hcd->hc_ptr_array[grxsts.b.chnum]; ++ if (!hc) { ++ DWC_ERROR("Unable to get corresponding channel\n"); ++ return 0; ++ } ++ ++ /* Packet Status */ ++ DWC_DEBUGPL(DBG_HCDV, " Ch num = %d\n", grxsts.b.chnum); ++ DWC_DEBUGPL(DBG_HCDV, " Count = %d\n", grxsts.b.bcnt); ++ DWC_DEBUGPL(DBG_HCDV, " DPID = %d, hc.dpid = %d\n", grxsts.b.dpid, ++ hc->data_pid_start); ++ DWC_DEBUGPL(DBG_HCDV, " PStatus = %d\n", grxsts.b.pktsts); ++ ++ switch (grxsts.b.pktsts) { ++ case DWC_GRXSTS_PKTSTS_IN: ++ /* Read the data into the host buffer. */ ++ if (grxsts.b.bcnt > 0) { ++ dwc_otg_read_packet(dwc_otg_hcd->core_if, ++ hc->xfer_buff, grxsts.b.bcnt); ++ ++ /* Update the HC fields for the next packet received. */ ++ hc->xfer_count += grxsts.b.bcnt; ++ hc->xfer_buff += grxsts.b.bcnt; ++ } ++ ++ case DWC_GRXSTS_PKTSTS_IN_XFER_COMP: ++ case DWC_GRXSTS_PKTSTS_DATA_TOGGLE_ERR: ++ case DWC_GRXSTS_PKTSTS_CH_HALTED: ++ /* Handled in interrupt, just ignore data */ ++ break; ++ default: ++ DWC_ERROR("RX_STS_Q Interrupt: Unknown status %d\n", ++ grxsts.b.pktsts); ++ break; ++ } ++ ++ return 1; ++} ++ ++/** This interrupt occurs when the non-periodic Tx FIFO is half-empty. More ++ * data packets may be written to the FIFO for OUT transfers. More requests ++ * may be written to the non-periodic request queue for IN transfers. This ++ * interrupt is enabled only in Slave mode. */ ++int32_t dwc_otg_hcd_handle_np_tx_fifo_empty_intr(dwc_otg_hcd_t * dwc_otg_hcd) ++{ ++ DWC_DEBUGPL(DBG_HCD, "--Non-Periodic TxFIFO Empty Interrupt--\n"); ++ dwc_otg_hcd_queue_transactions(dwc_otg_hcd, ++ DWC_OTG_TRANSACTION_NON_PERIODIC); ++ return 1; ++} ++ ++/** This interrupt occurs when the periodic Tx FIFO is half-empty. More data ++ * packets may be written to the FIFO for OUT transfers. More requests may be ++ * written to the periodic request queue for IN transfers. This interrupt is ++ * enabled only in Slave mode. */ ++int32_t dwc_otg_hcd_handle_perio_tx_fifo_empty_intr(dwc_otg_hcd_t * dwc_otg_hcd) ++{ ++ DWC_DEBUGPL(DBG_HCD, "--Periodic TxFIFO Empty Interrupt--\n"); ++ dwc_otg_hcd_queue_transactions(dwc_otg_hcd, ++ DWC_OTG_TRANSACTION_PERIODIC); ++ return 1; ++} ++ ++/** There are multiple conditions that can cause a port interrupt. This function ++ * determines which interrupt conditions have occurred and handles them ++ * appropriately. */ ++int32_t dwc_otg_hcd_handle_port_intr(dwc_otg_hcd_t * dwc_otg_hcd) ++{ ++ int retval = 0; ++ hprt0_data_t hprt0; ++ hprt0_data_t hprt0_modify; ++ ++ hprt0.d32 = DWC_READ_REG32(dwc_otg_hcd->core_if->host_if->hprt0); ++ hprt0_modify.d32 = DWC_READ_REG32(dwc_otg_hcd->core_if->host_if->hprt0); ++ ++ /* Clear appropriate bits in HPRT0 to clear the interrupt bit in ++ * GINTSTS */ ++ ++ hprt0_modify.b.prtena = 0; ++ hprt0_modify.b.prtconndet = 0; ++ hprt0_modify.b.prtenchng = 0; ++ hprt0_modify.b.prtovrcurrchng = 0; ++ ++ /* Port Connect Detected ++ * Set flag and clear if detected */ ++ if (dwc_otg_hcd->core_if->hibernation_suspend == 1) { ++ // Dont modify port status if we are in hibernation state ++ hprt0_modify.b.prtconndet = 1; ++ hprt0_modify.b.prtenchng = 1; ++ DWC_WRITE_REG32(dwc_otg_hcd->core_if->host_if->hprt0, hprt0_modify.d32); ++ hprt0.d32 = DWC_READ_REG32(dwc_otg_hcd->core_if->host_if->hprt0); ++ return retval; ++ } ++ ++ if (hprt0.b.prtconndet) { ++ /** @todo - check if steps performed in 'else' block should be perfromed regardles adp */ ++ if (dwc_otg_hcd->core_if->adp_enable && ++ dwc_otg_hcd->core_if->adp.vbuson_timer_started == 1) { ++ DWC_PRINTF("PORT CONNECT DETECTED ----------------\n"); ++ DWC_TIMER_CANCEL(dwc_otg_hcd->core_if->adp.vbuson_timer); ++ dwc_otg_hcd->core_if->adp.vbuson_timer_started = 0; ++ /* TODO - check if this is required, as ++ * host initialization was already performed ++ * after initial ADP probing ++ */ ++ /*dwc_otg_hcd->core_if->adp.vbuson_timer_started = 0; ++ dwc_otg_core_init(dwc_otg_hcd->core_if); ++ dwc_otg_enable_global_interrupts(dwc_otg_hcd->core_if); ++ cil_hcd_start(dwc_otg_hcd->core_if);*/ ++ } else { ++ ++ DWC_DEBUGPL(DBG_HCD, "--Port Interrupt HPRT0=0x%08x " ++ "Port Connect Detected--\n", hprt0.d32); ++ dwc_otg_hcd->flags.b.port_connect_status_change = 1; ++ dwc_otg_hcd->flags.b.port_connect_status = 1; ++ hprt0_modify.b.prtconndet = 1; ++ ++ /* B-Device has connected, Delete the connection timer. */ ++ DWC_TIMER_CANCEL(dwc_otg_hcd->conn_timer); ++ } ++ /* The Hub driver asserts a reset when it sees port connect ++ * status change flag */ ++ retval |= 1; ++ } ++ ++ /* Port Enable Changed ++ * Clear if detected - Set internal flag if disabled */ ++ if (hprt0.b.prtenchng) { ++ DWC_DEBUGPL(DBG_HCD, " --Port Interrupt HPRT0=0x%08x " ++ "Port Enable Changed--\n", hprt0.d32); ++ hprt0_modify.b.prtenchng = 1; ++ if (hprt0.b.prtena == 1) { ++ hfir_data_t hfir; ++ int do_reset = 0; ++ dwc_otg_core_params_t *params = ++ dwc_otg_hcd->core_if->core_params; ++ dwc_otg_core_global_regs_t *global_regs = ++ dwc_otg_hcd->core_if->core_global_regs; ++ dwc_otg_host_if_t *host_if = ++ dwc_otg_hcd->core_if->host_if; ++ ++ dwc_otg_hcd->flags.b.port_speed = hprt0.b.prtspd; ++ if (microframe_schedule) ++ init_hcd_usecs(dwc_otg_hcd); ++ ++ /* Every time when port enables calculate ++ * HFIR.FrInterval ++ */ ++ hfir.d32 = DWC_READ_REG32(&host_if->host_global_regs->hfir); ++ hfir.b.frint = calc_frame_interval(dwc_otg_hcd->core_if); ++ DWC_WRITE_REG32(&host_if->host_global_regs->hfir, hfir.d32); ++ ++ /* Check if we need to adjust the PHY clock speed for ++ * low power and adjust it */ ++ if (params->host_support_fs_ls_low_power) { ++ gusbcfg_data_t usbcfg; ++ ++ usbcfg.d32 = ++ DWC_READ_REG32(&global_regs->gusbcfg); ++ ++ if (hprt0.b.prtspd == DWC_HPRT0_PRTSPD_LOW_SPEED ++ || hprt0.b.prtspd == ++ DWC_HPRT0_PRTSPD_FULL_SPEED) { ++ /* ++ * Low power ++ */ ++ hcfg_data_t hcfg; ++ if (usbcfg.b.phylpwrclksel == 0) { ++ /* Set PHY low power clock select for FS/LS devices */ ++ usbcfg.b.phylpwrclksel = 1; ++ DWC_WRITE_REG32 ++ (&global_regs->gusbcfg, ++ usbcfg.d32); ++ do_reset = 1; ++ } ++ ++ hcfg.d32 = ++ DWC_READ_REG32 ++ (&host_if->host_global_regs->hcfg); ++ ++ if (hprt0.b.prtspd == ++ DWC_HPRT0_PRTSPD_LOW_SPEED ++ && params->host_ls_low_power_phy_clk ++ == ++ DWC_HOST_LS_LOW_POWER_PHY_CLK_PARAM_6MHZ) ++ { ++ /* 6 MHZ */ ++ DWC_DEBUGPL(DBG_CIL, ++ "FS_PHY programming HCFG to 6 MHz (Low Power)\n"); ++ if (hcfg.b.fslspclksel != ++ DWC_HCFG_6_MHZ) { ++ hcfg.b.fslspclksel = ++ DWC_HCFG_6_MHZ; ++ DWC_WRITE_REG32 ++ (&host_if->host_global_regs->hcfg, ++ hcfg.d32); ++ do_reset = 1; ++ } ++ } else { ++ /* 48 MHZ */ ++ DWC_DEBUGPL(DBG_CIL, ++ "FS_PHY programming HCFG to 48 MHz ()\n"); ++ if (hcfg.b.fslspclksel != ++ DWC_HCFG_48_MHZ) { ++ hcfg.b.fslspclksel = ++ DWC_HCFG_48_MHZ; ++ DWC_WRITE_REG32 ++ (&host_if->host_global_regs->hcfg, ++ hcfg.d32); ++ do_reset = 1; ++ } ++ } ++ } else { ++ /* ++ * Not low power ++ */ ++ if (usbcfg.b.phylpwrclksel == 1) { ++ usbcfg.b.phylpwrclksel = 0; ++ DWC_WRITE_REG32 ++ (&global_regs->gusbcfg, ++ usbcfg.d32); ++ do_reset = 1; ++ } ++ } ++ ++ if (do_reset) { ++ DWC_TASK_SCHEDULE(dwc_otg_hcd->reset_tasklet); ++ } ++ } ++ ++ if (!do_reset) { ++ /* Port has been enabled set the reset change flag */ ++ dwc_otg_hcd->flags.b.port_reset_change = 1; ++ } ++ } else { ++ dwc_otg_hcd->flags.b.port_enable_change = 1; ++ } ++ retval |= 1; ++ } ++ ++ /** Overcurrent Change Interrupt */ ++ if (hprt0.b.prtovrcurrchng) { ++ DWC_DEBUGPL(DBG_HCD, " --Port Interrupt HPRT0=0x%08x " ++ "Port Overcurrent Changed--\n", hprt0.d32); ++ dwc_otg_hcd->flags.b.port_over_current_change = 1; ++ hprt0_modify.b.prtovrcurrchng = 1; ++ retval |= 1; ++ } ++ ++ /* Clear Port Interrupts */ ++ DWC_WRITE_REG32(dwc_otg_hcd->core_if->host_if->hprt0, hprt0_modify.d32); ++ ++ return retval; ++} ++ ++/** This interrupt indicates that one or more host channels has a pending ++ * interrupt. There are multiple conditions that can cause each host channel ++ * interrupt. This function determines which conditions have occurred for each ++ * host channel interrupt and handles them appropriately. */ ++int32_t dwc_otg_hcd_handle_hc_intr(dwc_otg_hcd_t * dwc_otg_hcd) ++{ ++ int i; ++ int retval = 0; ++ haint_data_t haint = { .d32 = 0 } ; ++ ++ /* Clear appropriate bits in HCINTn to clear the interrupt bit in ++ * GINTSTS */ ++ ++ if (!fiq_fsm_enable) ++ haint.d32 = dwc_otg_read_host_all_channels_intr(dwc_otg_hcd->core_if); ++ ++ // Overwrite with saved interrupts from fiq handler ++ if(fiq_fsm_enable) ++ { ++ /* check the mask? */ ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&dwc_otg_hcd->fiq_state->lock); ++ haint.b2.chint |= ~(dwc_otg_hcd->fiq_state->haintmsk_saved.b2.chint); ++ dwc_otg_hcd->fiq_state->haintmsk_saved.b2.chint = ~0; ++ fiq_fsm_spin_unlock(&dwc_otg_hcd->fiq_state->lock); ++ local_fiq_enable(); ++ } ++ ++ for (i = 0; i < dwc_otg_hcd->core_if->core_params->host_channels; i++) { ++ if (haint.b2.chint & (1 << i)) { ++ retval |= dwc_otg_hcd_handle_hc_n_intr(dwc_otg_hcd, i); ++ } ++ } ++ ++ return retval; ++} ++ ++/** ++ * Gets the actual length of a transfer after the transfer halts. _halt_status ++ * holds the reason for the halt. ++ * ++ * For IN transfers where halt_status is DWC_OTG_HC_XFER_COMPLETE, ++ * *short_read is set to 1 upon return if less than the requested ++ * number of bytes were transferred. Otherwise, *short_read is set to 0 upon ++ * return. short_read may also be NULL on entry, in which case it remains ++ * unchanged. ++ */ ++static uint32_t get_actual_xfer_length(dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd, ++ dwc_otg_halt_status_e halt_status, ++ int *short_read) ++{ ++ hctsiz_data_t hctsiz; ++ uint32_t length; ++ ++ if (short_read != NULL) { ++ *short_read = 0; ++ } ++ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz); ++ ++ if (halt_status == DWC_OTG_HC_XFER_COMPLETE) { ++ if (hc->ep_is_in) { ++ length = hc->xfer_len - hctsiz.b.xfersize; ++ if (short_read != NULL) { ++ *short_read = (hctsiz.b.xfersize != 0); ++ } ++ } else if (hc->qh->do_split) { ++ //length = split_out_xfersize[hc->hc_num]; ++ length = qtd->ssplit_out_xfer_count; ++ } else { ++ length = hc->xfer_len; ++ } ++ } else { ++ /* ++ * Must use the hctsiz.pktcnt field to determine how much data ++ * has been transferred. This field reflects the number of ++ * packets that have been transferred via the USB. This is ++ * always an integral number of packets if the transfer was ++ * halted before its normal completion. (Can't use the ++ * hctsiz.xfersize field because that reflects the number of ++ * bytes transferred via the AHB, not the USB). ++ */ ++ length = ++ (hc->start_pkt_count - hctsiz.b.pktcnt) * hc->max_packet; ++ } ++ ++ return length; ++} ++ ++/** ++ * Updates the state of the URB after a Transfer Complete interrupt on the ++ * host channel. Updates the actual_length field of the URB based on the ++ * number of bytes transferred via the host channel. Sets the URB status ++ * if the data transfer is finished. ++ * ++ * @return 1 if the data transfer specified by the URB is completely finished, ++ * 0 otherwise. ++ */ ++static int update_urb_state_xfer_comp(dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_hcd_urb_t * urb, ++ dwc_otg_qtd_t * qtd) ++{ ++ int xfer_done = 0; ++ int short_read = 0; ++ ++ int xfer_length; ++ ++ xfer_length = get_actual_xfer_length(hc, hc_regs, qtd, ++ DWC_OTG_HC_XFER_COMPLETE, ++ &short_read); ++ ++ if (urb->actual_length + xfer_length > urb->length) { ++ printk_once(KERN_DEBUG "dwc_otg: DEVICE:%03d : %s:%d:trimming xfer length\n", ++ hc->dev_addr, __func__, __LINE__); ++ xfer_length = urb->length - urb->actual_length; ++ } ++ ++ /* non DWORD-aligned buffer case handling. */ ++ if (hc->align_buff && xfer_length && hc->ep_is_in) { ++ dwc_memcpy(urb->buf + urb->actual_length, hc->qh->dw_align_buf, ++ xfer_length); ++ } ++ ++ urb->actual_length += xfer_length; ++ ++ if (xfer_length && (hc->ep_type == DWC_OTG_EP_TYPE_BULK) && ++ (urb->flags & URB_SEND_ZERO_PACKET) ++ && (urb->actual_length == urb->length) ++ && !(urb->length % hc->max_packet)) { ++ xfer_done = 0; ++ } else if (short_read || urb->actual_length >= urb->length) { ++ xfer_done = 1; ++ urb->status = 0; ++ } ++ ++#ifdef DEBUG ++ { ++ hctsiz_data_t hctsiz; ++ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz); ++ DWC_DEBUGPL(DBG_HCDV, "DWC_otg: %s: %s, channel %d\n", ++ __func__, (hc->ep_is_in ? "IN" : "OUT"), ++ hc->hc_num); ++ DWC_DEBUGPL(DBG_HCDV, " hc->xfer_len %d\n", hc->xfer_len); ++ DWC_DEBUGPL(DBG_HCDV, " hctsiz.xfersize %d\n", ++ hctsiz.b.xfersize); ++ DWC_DEBUGPL(DBG_HCDV, " urb->transfer_buffer_length %d\n", ++ urb->length); ++ DWC_DEBUGPL(DBG_HCDV, " urb->actual_length %d\n", ++ urb->actual_length); ++ DWC_DEBUGPL(DBG_HCDV, " short_read %d, xfer_done %d\n", ++ short_read, xfer_done); ++ } ++#endif ++ ++ return xfer_done; ++} ++ ++/* ++ * Save the starting data toggle for the next transfer. The data toggle is ++ * saved in the QH for non-control transfers and it's saved in the QTD for ++ * control transfers. ++ */ ++void dwc_otg_hcd_save_data_toggle(dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, dwc_otg_qtd_t * qtd) ++{ ++ hctsiz_data_t hctsiz; ++ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz); ++ ++ if (hc->ep_type != DWC_OTG_EP_TYPE_CONTROL) { ++ dwc_otg_qh_t *qh = hc->qh; ++ if (hctsiz.b.pid == DWC_HCTSIZ_DATA0) { ++ qh->data_toggle = DWC_OTG_HC_PID_DATA0; ++ } else { ++ qh->data_toggle = DWC_OTG_HC_PID_DATA1; ++ } ++ } else { ++ if (hctsiz.b.pid == DWC_HCTSIZ_DATA0) { ++ qtd->data_toggle = DWC_OTG_HC_PID_DATA0; ++ } else { ++ qtd->data_toggle = DWC_OTG_HC_PID_DATA1; ++ } ++ } ++} ++ ++/** ++ * Updates the state of an Isochronous URB when the transfer is stopped for ++ * any reason. The fields of the current entry in the frame descriptor array ++ * are set based on the transfer state and the input _halt_status. Completes ++ * the Isochronous URB if all the URB frames have been completed. ++ * ++ * @return DWC_OTG_HC_XFER_COMPLETE if there are more frames remaining to be ++ * transferred in the URB. Otherwise return DWC_OTG_HC_XFER_URB_COMPLETE. ++ */ ++static dwc_otg_halt_status_e ++update_isoc_urb_state(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd, dwc_otg_halt_status_e halt_status) ++{ ++ dwc_otg_hcd_urb_t *urb = qtd->urb; ++ dwc_otg_halt_status_e ret_val = halt_status; ++ struct dwc_otg_hcd_iso_packet_desc *frame_desc; ++ ++ frame_desc = &urb->iso_descs[qtd->isoc_frame_index]; ++ switch (halt_status) { ++ case DWC_OTG_HC_XFER_COMPLETE: ++ frame_desc->status = 0; ++ frame_desc->actual_length = ++ get_actual_xfer_length(hc, hc_regs, qtd, halt_status, NULL); ++ ++ /* non DWORD-aligned buffer case handling. */ ++ if (hc->align_buff && frame_desc->actual_length && hc->ep_is_in) { ++ dwc_memcpy(urb->buf + frame_desc->offset + qtd->isoc_split_offset, ++ hc->qh->dw_align_buf, frame_desc->actual_length); ++ } ++ ++ break; ++ case DWC_OTG_HC_XFER_FRAME_OVERRUN: ++ urb->error_count++; ++ if (hc->ep_is_in) { ++ frame_desc->status = -DWC_E_NO_STREAM_RES; ++ } else { ++ frame_desc->status = -DWC_E_COMMUNICATION; ++ } ++ frame_desc->actual_length = 0; ++ break; ++ case DWC_OTG_HC_XFER_BABBLE_ERR: ++ urb->error_count++; ++ frame_desc->status = -DWC_E_OVERFLOW; ++ /* Don't need to update actual_length in this case. */ ++ break; ++ case DWC_OTG_HC_XFER_XACT_ERR: ++ urb->error_count++; ++ frame_desc->status = -DWC_E_PROTOCOL; ++ frame_desc->actual_length = ++ get_actual_xfer_length(hc, hc_regs, qtd, halt_status, NULL); ++ ++ /* non DWORD-aligned buffer case handling. */ ++ if (hc->align_buff && frame_desc->actual_length && hc->ep_is_in) { ++ dwc_memcpy(urb->buf + frame_desc->offset + qtd->isoc_split_offset, ++ hc->qh->dw_align_buf, frame_desc->actual_length); ++ } ++ /* Skip whole frame */ ++ if (hc->qh->do_split && (hc->ep_type == DWC_OTG_EP_TYPE_ISOC) && ++ hc->ep_is_in && hcd->core_if->dma_enable) { ++ qtd->complete_split = 0; ++ qtd->isoc_split_offset = 0; ++ } ++ ++ break; ++ default: ++ DWC_ASSERT(1, "Unhandled _halt_status (%d)\n", halt_status); ++ break; ++ } ++ if (++qtd->isoc_frame_index == urb->packet_count) { ++ /* ++ * urb->status is not used for isoc transfers. ++ * The individual frame_desc statuses are used instead. ++ */ ++ hcd->fops->complete(hcd, urb->priv, urb, 0); ++ ret_val = DWC_OTG_HC_XFER_URB_COMPLETE; ++ } else { ++ ret_val = DWC_OTG_HC_XFER_COMPLETE; ++ } ++ return ret_val; ++} ++ ++/** ++ * Frees the first QTD in the QH's list if free_qtd is 1. For non-periodic ++ * QHs, removes the QH from the active non-periodic schedule. If any QTDs are ++ * still linked to the QH, the QH is added to the end of the inactive ++ * non-periodic schedule. For periodic QHs, removes the QH from the periodic ++ * schedule if no more QTDs are linked to the QH. ++ */ ++static void deactivate_qh(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh, int free_qtd) ++{ ++ int continue_split = 0; ++ dwc_otg_qtd_t *qtd; ++ ++ DWC_DEBUGPL(DBG_HCDV, " %s(%p,%p,%d)\n", __func__, hcd, qh, free_qtd); ++ ++ qtd = DWC_CIRCLEQ_FIRST(&qh->qtd_list); ++ ++ if (qtd->complete_split) { ++ continue_split = 1; ++ } else if (qtd->isoc_split_pos == DWC_HCSPLIT_XACTPOS_MID || ++ qtd->isoc_split_pos == DWC_HCSPLIT_XACTPOS_END) { ++ continue_split = 1; ++ } ++ ++ if (free_qtd) { ++ dwc_otg_hcd_qtd_remove_and_free(hcd, qtd, qh); ++ continue_split = 0; ++ } ++ ++ qh->channel = NULL; ++ dwc_otg_hcd_qh_deactivate(hcd, qh, continue_split); ++} ++ ++/** ++ * Releases a host channel for use by other transfers. Attempts to select and ++ * queue more transactions since at least one host channel is available. ++ * ++ * @param hcd The HCD state structure. ++ * @param hc The host channel to release. ++ * @param qtd The QTD associated with the host channel. This QTD may be freed ++ * if the transfer is complete or an error has occurred. ++ * @param halt_status Reason the channel is being released. This status ++ * determines the actions taken by this function. ++ */ ++static void release_channel(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_qtd_t * qtd, ++ dwc_otg_halt_status_e halt_status) ++{ ++ dwc_otg_transaction_type_e tr_type; ++ int free_qtd; ++ ++ int hog_port = 0; ++ ++ DWC_DEBUGPL(DBG_HCDV, " %s: channel %d, halt_status %d, xfer_len %d\n", ++ __func__, hc->hc_num, halt_status, hc->xfer_len); ++ ++ if(fiq_fsm_enable && hc->do_split) { ++ if(!hc->ep_is_in && hc->ep_type == UE_ISOCHRONOUS) { ++ if(hc->xact_pos == DWC_HCSPLIT_XACTPOS_MID || ++ hc->xact_pos == DWC_HCSPLIT_XACTPOS_BEGIN) { ++ hog_port = 0; ++ } ++ } ++ } ++ ++ switch (halt_status) { ++ case DWC_OTG_HC_XFER_URB_COMPLETE: ++ free_qtd = 1; ++ break; ++ case DWC_OTG_HC_XFER_AHB_ERR: ++ case DWC_OTG_HC_XFER_STALL: ++ case DWC_OTG_HC_XFER_BABBLE_ERR: ++ free_qtd = 1; ++ break; ++ case DWC_OTG_HC_XFER_XACT_ERR: ++ if (qtd->error_count >= 3) { ++ DWC_DEBUGPL(DBG_HCDV, ++ " Complete URB with transaction error\n"); ++ free_qtd = 1; ++ qtd->urb->status = -DWC_E_PROTOCOL; ++ hcd->fops->complete(hcd, qtd->urb->priv, ++ qtd->urb, -DWC_E_PROTOCOL); ++ } else { ++ free_qtd = 0; ++ } ++ break; ++ case DWC_OTG_HC_XFER_URB_DEQUEUE: ++ /* ++ * The QTD has already been removed and the QH has been ++ * deactivated. Don't want to do anything except release the ++ * host channel and try to queue more transfers. ++ */ ++ goto cleanup; ++ case DWC_OTG_HC_XFER_NO_HALT_STATUS: ++ free_qtd = 0; ++ break; ++ case DWC_OTG_HC_XFER_PERIODIC_INCOMPLETE: ++ DWC_DEBUGPL(DBG_HCDV, ++ " Complete URB with I/O error\n"); ++ free_qtd = 1; ++ qtd->urb->status = -DWC_E_IO; ++ hcd->fops->complete(hcd, qtd->urb->priv, ++ qtd->urb, -DWC_E_IO); ++ break; ++ default: ++ free_qtd = 0; ++ break; ++ } ++ ++ deactivate_qh(hcd, hc->qh, free_qtd); ++ ++cleanup: ++ /* ++ * Release the host channel for use by other transfers. The cleanup ++ * function clears the channel interrupt enables and conditions, so ++ * there's no need to clear the Channel Halted interrupt separately. ++ */ ++ if (fiq_fsm_enable && hcd->fiq_state->channel[hc->hc_num].fsm != FIQ_PASSTHROUGH) ++ dwc_otg_cleanup_fiq_channel(hcd, hc->hc_num); ++ dwc_otg_hc_cleanup(hcd->core_if, hc); ++ DWC_CIRCLEQ_INSERT_TAIL(&hcd->free_hc_list, hc, hc_list_entry); ++ ++ if (!microframe_schedule) { ++ switch (hc->ep_type) { ++ case DWC_OTG_EP_TYPE_CONTROL: ++ case DWC_OTG_EP_TYPE_BULK: ++ hcd->non_periodic_channels--; ++ break; ++ ++ default: ++ /* ++ * Don't release reservations for periodic channels here. ++ * That's done when a periodic transfer is descheduled (i.e. ++ * when the QH is removed from the periodic schedule). ++ */ ++ break; ++ } ++ } else { ++ hcd->available_host_channels++; ++ fiq_print(FIQDBG_INT, hcd->fiq_state, "AHC = %d ", hcd->available_host_channels); ++ } ++ ++ /* Try to queue more transfers now that there's a free channel. */ ++ tr_type = dwc_otg_hcd_select_transactions(hcd); ++ if (tr_type != DWC_OTG_TRANSACTION_NONE) { ++ dwc_otg_hcd_queue_transactions(hcd, tr_type); ++ } ++} ++ ++/** ++ * Halts a host channel. If the channel cannot be halted immediately because ++ * the request queue is full, this function ensures that the FIFO empty ++ * interrupt for the appropriate queue is enabled so that the halt request can ++ * be queued when there is space in the request queue. ++ * ++ * This function may also be called in DMA mode. In that case, the channel is ++ * simply released since the core always halts the channel automatically in ++ * DMA mode. ++ */ ++static void halt_channel(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_qtd_t * qtd, dwc_otg_halt_status_e halt_status) ++{ ++ if (hcd->core_if->dma_enable) { ++ release_channel(hcd, hc, qtd, halt_status); ++ return; ++ } ++ ++ /* Slave mode processing... */ ++ dwc_otg_hc_halt(hcd->core_if, hc, halt_status); ++ ++ if (hc->halt_on_queue) { ++ gintmsk_data_t gintmsk = {.d32 = 0 }; ++ dwc_otg_core_global_regs_t *global_regs; ++ global_regs = hcd->core_if->core_global_regs; ++ ++ if (hc->ep_type == DWC_OTG_EP_TYPE_CONTROL || ++ hc->ep_type == DWC_OTG_EP_TYPE_BULK) { ++ /* ++ * Make sure the Non-periodic Tx FIFO empty interrupt ++ * is enabled so that the non-periodic schedule will ++ * be processed. ++ */ ++ gintmsk.b.nptxfempty = 1; ++ if (fiq_enable) { ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&hcd->fiq_state->lock); ++ DWC_MODIFY_REG32(&global_regs->gintmsk, 0, gintmsk.d32); ++ fiq_fsm_spin_unlock(&hcd->fiq_state->lock); ++ local_fiq_enable(); ++ } else { ++ DWC_MODIFY_REG32(&global_regs->gintmsk, 0, gintmsk.d32); ++ } ++ } else { ++ /* ++ * Move the QH from the periodic queued schedule to ++ * the periodic assigned schedule. This allows the ++ * halt to be queued when the periodic schedule is ++ * processed. ++ */ ++ DWC_LIST_MOVE_HEAD(&hcd->periodic_sched_assigned, ++ &hc->qh->qh_list_entry); ++ ++ /* ++ * Make sure the Periodic Tx FIFO Empty interrupt is ++ * enabled so that the periodic schedule will be ++ * processed. ++ */ ++ gintmsk.b.ptxfempty = 1; ++ if (fiq_enable) { ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&hcd->fiq_state->lock); ++ DWC_MODIFY_REG32(&global_regs->gintmsk, 0, gintmsk.d32); ++ fiq_fsm_spin_unlock(&hcd->fiq_state->lock); ++ local_fiq_enable(); ++ } else { ++ DWC_MODIFY_REG32(&global_regs->gintmsk, 0, gintmsk.d32); ++ } ++ } ++ } ++} ++ ++/** ++ * Performs common cleanup for non-periodic transfers after a Transfer ++ * Complete interrupt. This function should be called after any endpoint type ++ * specific handling is finished to release the host channel. ++ */ ++static void complete_non_periodic_xfer(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd, ++ dwc_otg_halt_status_e halt_status) ++{ ++ hcint_data_t hcint; ++ ++ qtd->error_count = 0; ++ ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ if (hcint.b.nyet) { ++ /* ++ * Got a NYET on the last transaction of the transfer. This ++ * means that the endpoint should be in the PING state at the ++ * beginning of the next transfer. ++ */ ++ hc->qh->ping_state = 1; ++ clear_hc_int(hc_regs, nyet); ++ } ++ ++ /* ++ * Always halt and release the host channel to make it available for ++ * more transfers. There may still be more phases for a control ++ * transfer or more data packets for a bulk transfer at this point, ++ * but the host channel is still halted. A channel will be reassigned ++ * to the transfer when the non-periodic schedule is processed after ++ * the channel is released. This allows transactions to be queued ++ * properly via dwc_otg_hcd_queue_transactions, which also enables the ++ * Tx FIFO Empty interrupt if necessary. ++ */ ++ if (hc->ep_is_in) { ++ /* ++ * IN transfers in Slave mode require an explicit disable to ++ * halt the channel. (In DMA mode, this call simply releases ++ * the channel.) ++ */ ++ halt_channel(hcd, hc, qtd, halt_status); ++ } else { ++ /* ++ * The channel is automatically disabled by the core for OUT ++ * transfers in Slave mode. ++ */ ++ release_channel(hcd, hc, qtd, halt_status); ++ } ++} ++ ++/** ++ * Performs common cleanup for periodic transfers after a Transfer Complete ++ * interrupt. This function should be called after any endpoint type specific ++ * handling is finished to release the host channel. ++ */ ++static void complete_periodic_xfer(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd, ++ dwc_otg_halt_status_e halt_status) ++{ ++ hctsiz_data_t hctsiz; ++ qtd->error_count = 0; ++ ++ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz); ++ if (!hc->ep_is_in || hctsiz.b.pktcnt == 0) { ++ /* Core halts channel in these cases. */ ++ release_channel(hcd, hc, qtd, halt_status); ++ } else { ++ /* Flush any outstanding requests from the Tx queue. */ ++ halt_channel(hcd, hc, qtd, halt_status); ++ } ++} ++ ++static int32_t handle_xfercomp_isoc_split_in(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ uint32_t len; ++ struct dwc_otg_hcd_iso_packet_desc *frame_desc; ++ frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index]; ++ ++ len = get_actual_xfer_length(hc, hc_regs, qtd, ++ DWC_OTG_HC_XFER_COMPLETE, NULL); ++ ++ if (!len) { ++ qtd->complete_split = 0; ++ qtd->isoc_split_offset = 0; ++ return 0; ++ } ++ frame_desc->actual_length += len; ++ ++ if (hc->align_buff && len) ++ dwc_memcpy(qtd->urb->buf + frame_desc->offset + ++ qtd->isoc_split_offset, hc->qh->dw_align_buf, len); ++ qtd->isoc_split_offset += len; ++ ++ if (frame_desc->length == frame_desc->actual_length) { ++ frame_desc->status = 0; ++ qtd->isoc_frame_index++; ++ qtd->complete_split = 0; ++ qtd->isoc_split_offset = 0; ++ } ++ ++ if (qtd->isoc_frame_index == qtd->urb->packet_count) { ++ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE); ++ } else { ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS); ++ } ++ ++ return 1; /* Indicates that channel released */ ++} ++ ++/** ++ * Handles a host channel Transfer Complete interrupt. This handler may be ++ * called in either DMA mode or Slave mode. ++ */ ++static int32_t handle_hc_xfercomp_intr(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ int urb_xfer_done; ++ dwc_otg_halt_status_e halt_status = DWC_OTG_HC_XFER_COMPLETE; ++ dwc_otg_hcd_urb_t *urb = qtd->urb; ++ int pipe_type = dwc_otg_hcd_get_pipe_type(&urb->pipe_info); ++ ++ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: " ++ "Transfer Complete--\n", hc->hc_num); ++ ++ if (hcd->core_if->dma_desc_enable) { ++ dwc_otg_hcd_complete_xfer_ddma(hcd, hc, hc_regs, halt_status); ++ if (pipe_type == UE_ISOCHRONOUS) { ++ /* Do not disable the interrupt, just clear it */ ++ clear_hc_int(hc_regs, xfercomp); ++ return 1; ++ } ++ goto handle_xfercomp_done; ++ } ++ ++ /* ++ * Handle xfer complete on CSPLIT. ++ */ ++ ++ if (hc->qh->do_split) { ++ if ((hc->ep_type == DWC_OTG_EP_TYPE_ISOC) && hc->ep_is_in ++ && hcd->core_if->dma_enable) { ++ if (qtd->complete_split ++ && handle_xfercomp_isoc_split_in(hcd, hc, hc_regs, ++ qtd)) ++ goto handle_xfercomp_done; ++ } else { ++ qtd->complete_split = 0; ++ } ++ } ++ ++ /* Update the QTD and URB states. */ ++ switch (pipe_type) { ++ case UE_CONTROL: ++ switch (qtd->control_phase) { ++ case DWC_OTG_CONTROL_SETUP: ++ if (urb->length > 0) { ++ qtd->control_phase = DWC_OTG_CONTROL_DATA; ++ } else { ++ qtd->control_phase = DWC_OTG_CONTROL_STATUS; ++ } ++ DWC_DEBUGPL(DBG_HCDV, ++ " Control setup transaction done\n"); ++ halt_status = DWC_OTG_HC_XFER_COMPLETE; ++ break; ++ case DWC_OTG_CONTROL_DATA:{ ++ urb_xfer_done = ++ update_urb_state_xfer_comp(hc, hc_regs, urb, ++ qtd); ++ if (urb_xfer_done) { ++ qtd->control_phase = ++ DWC_OTG_CONTROL_STATUS; ++ DWC_DEBUGPL(DBG_HCDV, ++ " Control data transfer done\n"); ++ } else { ++ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd); ++ } ++ halt_status = DWC_OTG_HC_XFER_COMPLETE; ++ break; ++ } ++ case DWC_OTG_CONTROL_STATUS: ++ DWC_DEBUGPL(DBG_HCDV, " Control transfer complete\n"); ++ if (urb->status == -DWC_E_IN_PROGRESS) { ++ urb->status = 0; ++ } ++ hcd->fops->complete(hcd, urb->priv, urb, urb->status); ++ halt_status = DWC_OTG_HC_XFER_URB_COMPLETE; ++ break; ++ } ++ ++ complete_non_periodic_xfer(hcd, hc, hc_regs, qtd, halt_status); ++ break; ++ case UE_BULK: ++ DWC_DEBUGPL(DBG_HCDV, " Bulk transfer complete\n"); ++ urb_xfer_done = ++ update_urb_state_xfer_comp(hc, hc_regs, urb, qtd); ++ if (urb_xfer_done) { ++ hcd->fops->complete(hcd, urb->priv, urb, urb->status); ++ halt_status = DWC_OTG_HC_XFER_URB_COMPLETE; ++ } else { ++ halt_status = DWC_OTG_HC_XFER_COMPLETE; ++ } ++ ++ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd); ++ complete_non_periodic_xfer(hcd, hc, hc_regs, qtd, halt_status); ++ break; ++ case UE_INTERRUPT: ++ DWC_DEBUGPL(DBG_HCDV, " Interrupt transfer complete\n"); ++ urb_xfer_done = ++ update_urb_state_xfer_comp(hc, hc_regs, urb, qtd); ++ ++ /* ++ * Interrupt URB is done on the first transfer complete ++ * interrupt. ++ */ ++ if (urb_xfer_done) { ++ hcd->fops->complete(hcd, urb->priv, urb, urb->status); ++ halt_status = DWC_OTG_HC_XFER_URB_COMPLETE; ++ } else { ++ halt_status = DWC_OTG_HC_XFER_COMPLETE; ++ } ++ ++ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd); ++ complete_periodic_xfer(hcd, hc, hc_regs, qtd, halt_status); ++ break; ++ case UE_ISOCHRONOUS: ++ DWC_DEBUGPL(DBG_HCDV, " Isochronous transfer complete\n"); ++ if (qtd->isoc_split_pos == DWC_HCSPLIT_XACTPOS_ALL) { ++ halt_status = ++ update_isoc_urb_state(hcd, hc, hc_regs, qtd, ++ DWC_OTG_HC_XFER_COMPLETE); ++ } ++ complete_periodic_xfer(hcd, hc, hc_regs, qtd, halt_status); ++ break; ++ } ++ ++handle_xfercomp_done: ++ disable_hc_int(hc_regs, xfercompl); ++ ++ return 1; ++} ++ ++/** ++ * Handles a host channel STALL interrupt. This handler may be called in ++ * either DMA mode or Slave mode. ++ */ ++static int32_t handle_hc_stall_intr(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ dwc_otg_hcd_urb_t *urb = qtd->urb; ++ int pipe_type = dwc_otg_hcd_get_pipe_type(&urb->pipe_info); ++ ++ DWC_DEBUGPL(DBG_HCD, "--Host Channel %d Interrupt: " ++ "STALL Received--\n", hc->hc_num); ++ ++ if (hcd->core_if->dma_desc_enable) { ++ dwc_otg_hcd_complete_xfer_ddma(hcd, hc, hc_regs, DWC_OTG_HC_XFER_STALL); ++ goto handle_stall_done; ++ } ++ ++ if (pipe_type == UE_CONTROL) { ++ hcd->fops->complete(hcd, urb->priv, urb, -DWC_E_PIPE); ++ } ++ ++ if (pipe_type == UE_BULK || pipe_type == UE_INTERRUPT) { ++ hcd->fops->complete(hcd, urb->priv, urb, -DWC_E_PIPE); ++ /* ++ * USB protocol requires resetting the data toggle for bulk ++ * and interrupt endpoints when a CLEAR_FEATURE(ENDPOINT_HALT) ++ * setup command is issued to the endpoint. Anticipate the ++ * CLEAR_FEATURE command since a STALL has occurred and reset ++ * the data toggle now. ++ */ ++ hc->qh->data_toggle = 0; ++ } ++ ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_STALL); ++ ++handle_stall_done: ++ disable_hc_int(hc_regs, stall); ++ ++ return 1; ++} ++ ++/* ++ * Updates the state of the URB when a transfer has been stopped due to an ++ * abnormal condition before the transfer completes. Modifies the ++ * actual_length field of the URB to reflect the number of bytes that have ++ * actually been transferred via the host channel. ++ */ ++static void update_urb_state_xfer_intr(dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_hcd_urb_t * urb, ++ dwc_otg_qtd_t * qtd, ++ dwc_otg_halt_status_e halt_status) ++{ ++ uint32_t bytes_transferred = get_actual_xfer_length(hc, hc_regs, qtd, ++ halt_status, NULL); ++ ++ if (urb->actual_length + bytes_transferred > urb->length) { ++ printk_once(KERN_DEBUG "dwc_otg: DEVICE:%03d : %s:%d:trimming xfer length\n", ++ hc->dev_addr, __func__, __LINE__); ++ bytes_transferred = urb->length - urb->actual_length; ++ } ++ ++ /* non DWORD-aligned buffer case handling. */ ++ if (hc->align_buff && bytes_transferred && hc->ep_is_in) { ++ dwc_memcpy(urb->buf + urb->actual_length, hc->qh->dw_align_buf, ++ bytes_transferred); ++ } ++ ++ urb->actual_length += bytes_transferred; ++ ++#ifdef DEBUG ++ { ++ hctsiz_data_t hctsiz; ++ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz); ++ DWC_DEBUGPL(DBG_HCDV, "DWC_otg: %s: %s, channel %d\n", ++ __func__, (hc->ep_is_in ? "IN" : "OUT"), ++ hc->hc_num); ++ DWC_DEBUGPL(DBG_HCDV, " hc->start_pkt_count %d\n", ++ hc->start_pkt_count); ++ DWC_DEBUGPL(DBG_HCDV, " hctsiz.pktcnt %d\n", hctsiz.b.pktcnt); ++ DWC_DEBUGPL(DBG_HCDV, " hc->max_packet %d\n", hc->max_packet); ++ DWC_DEBUGPL(DBG_HCDV, " bytes_transferred %d\n", ++ bytes_transferred); ++ DWC_DEBUGPL(DBG_HCDV, " urb->actual_length %d\n", ++ urb->actual_length); ++ DWC_DEBUGPL(DBG_HCDV, " urb->transfer_buffer_length %d\n", ++ urb->length); ++ } ++#endif ++} ++ ++/** ++ * Handles a host channel NAK interrupt. This handler may be called in either ++ * DMA mode or Slave mode. ++ */ ++static int32_t handle_hc_nak_intr(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: " ++ "NAK Received--\n", hc->hc_num); ++ ++ /* ++ * When we get bulk NAKs then remember this so we holdoff on this qh until ++ * the beginning of the next frame ++ */ ++ switch(dwc_otg_hcd_get_pipe_type(&qtd->urb->pipe_info)) { ++ case UE_BULK: ++ case UE_CONTROL: ++ if (nak_holdoff && qtd->qh->do_split) ++ hc->qh->nak_frame = dwc_otg_hcd_get_frame_number(hcd); ++ } ++ ++ /* ++ * Handle NAK for IN/OUT SSPLIT/CSPLIT transfers, bulk, control, and ++ * interrupt. Re-start the SSPLIT transfer. ++ */ ++ if (hc->do_split) { ++ if (hc->complete_split) { ++ qtd->error_count = 0; ++ } ++ qtd->complete_split = 0; ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NAK); ++ goto handle_nak_done; ++ } ++ ++ switch (dwc_otg_hcd_get_pipe_type(&qtd->urb->pipe_info)) { ++ case UE_CONTROL: ++ case UE_BULK: ++ if (hcd->core_if->dma_enable && hc->ep_is_in) { ++ /* ++ * NAK interrupts are enabled on bulk/control IN ++ * transfers in DMA mode for the sole purpose of ++ * resetting the error count after a transaction error ++ * occurs. The core will continue transferring data. ++ * Disable other interrupts unmasked for the same ++ * reason. ++ */ ++ disable_hc_int(hc_regs, datatglerr); ++ disable_hc_int(hc_regs, ack); ++ qtd->error_count = 0; ++ goto handle_nak_done; ++ } ++ ++ /* ++ * NAK interrupts normally occur during OUT transfers in DMA ++ * or Slave mode. For IN transfers, more requests will be ++ * queued as request queue space is available. ++ */ ++ qtd->error_count = 0; ++ ++ if (!hc->qh->ping_state) { ++ update_urb_state_xfer_intr(hc, hc_regs, ++ qtd->urb, qtd, ++ DWC_OTG_HC_XFER_NAK); ++ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd); ++ ++ if (hc->speed == DWC_OTG_EP_SPEED_HIGH) ++ hc->qh->ping_state = 1; ++ } ++ ++ /* ++ * Halt the channel so the transfer can be re-started from ++ * the appropriate point or the PING protocol will ++ * start/continue. ++ */ ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NAK); ++ break; ++ case UE_INTERRUPT: ++ qtd->error_count = 0; ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NAK); ++ break; ++ case UE_ISOCHRONOUS: ++ /* Should never get called for isochronous transfers. */ ++ DWC_ASSERT(1, "NACK interrupt for ISOC transfer\n"); ++ break; ++ } ++ ++handle_nak_done: ++ disable_hc_int(hc_regs, nak); ++ ++ return 1; ++} ++ ++/** ++ * Handles a host channel ACK interrupt. This interrupt is enabled when ++ * performing the PING protocol in Slave mode, when errors occur during ++ * either Slave mode or DMA mode, and during Start Split transactions. ++ */ ++static int32_t handle_hc_ack_intr(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: " ++ "ACK Received--\n", hc->hc_num); ++ ++ if (hc->do_split) { ++ /* ++ * Handle ACK on SSPLIT. ++ * ACK should not occur in CSPLIT. ++ */ ++ if (!hc->ep_is_in && hc->data_pid_start != DWC_OTG_HC_PID_SETUP) { ++ qtd->ssplit_out_xfer_count = hc->xfer_len; ++ } ++ if (!(hc->ep_type == DWC_OTG_EP_TYPE_ISOC && !hc->ep_is_in)) { ++ /* Don't need complete for isochronous out transfers. */ ++ qtd->complete_split = 1; ++ } ++ ++ /* ISOC OUT */ ++ if (hc->ep_type == DWC_OTG_EP_TYPE_ISOC && !hc->ep_is_in) { ++ switch (hc->xact_pos) { ++ case DWC_HCSPLIT_XACTPOS_ALL: ++ break; ++ case DWC_HCSPLIT_XACTPOS_END: ++ qtd->isoc_split_pos = DWC_HCSPLIT_XACTPOS_ALL; ++ qtd->isoc_split_offset = 0; ++ break; ++ case DWC_HCSPLIT_XACTPOS_BEGIN: ++ case DWC_HCSPLIT_XACTPOS_MID: ++ /* ++ * For BEGIN or MID, calculate the length for ++ * the next microframe to determine the correct ++ * SSPLIT token, either MID or END. ++ */ ++ { ++ struct dwc_otg_hcd_iso_packet_desc ++ *frame_desc; ++ ++ frame_desc = ++ &qtd->urb-> ++ iso_descs[qtd->isoc_frame_index]; ++ qtd->isoc_split_offset += 188; ++ ++ if ((frame_desc->length - ++ qtd->isoc_split_offset) <= 188) { ++ qtd->isoc_split_pos = ++ DWC_HCSPLIT_XACTPOS_END; ++ } else { ++ qtd->isoc_split_pos = ++ DWC_HCSPLIT_XACTPOS_MID; ++ } ++ ++ } ++ break; ++ } ++ } else { ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_ACK); ++ } ++ } else { ++ /* ++ * An unmasked ACK on a non-split DMA transaction is ++ * for the sole purpose of resetting error counts. Disable other ++ * interrupts unmasked for the same reason. ++ */ ++ if(hcd->core_if->dma_enable) { ++ disable_hc_int(hc_regs, datatglerr); ++ disable_hc_int(hc_regs, nak); ++ } ++ qtd->error_count = 0; ++ ++ if (hc->qh->ping_state) { ++ hc->qh->ping_state = 0; ++ /* ++ * Halt the channel so the transfer can be re-started ++ * from the appropriate point. This only happens in ++ * Slave mode. In DMA mode, the ping_state is cleared ++ * when the transfer is started because the core ++ * automatically executes the PING, then the transfer. ++ */ ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_ACK); ++ } ++ } ++ ++ /* ++ * If the ACK occurred when _not_ in the PING state, let the channel ++ * continue transferring data after clearing the error count. ++ */ ++ ++ disable_hc_int(hc_regs, ack); ++ ++ return 1; ++} ++ ++/** ++ * Handles a host channel NYET interrupt. This interrupt should only occur on ++ * Bulk and Control OUT endpoints and for complete split transactions. If a ++ * NYET occurs at the same time as a Transfer Complete interrupt, it is ++ * handled in the xfercomp interrupt handler, not here. This handler may be ++ * called in either DMA mode or Slave mode. ++ */ ++static int32_t handle_hc_nyet_intr(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: " ++ "NYET Received--\n", hc->hc_num); ++ ++ /* ++ * NYET on CSPLIT ++ * re-do the CSPLIT immediately on non-periodic ++ */ ++ if (hc->do_split && hc->complete_split) { ++ if (hc->ep_is_in && (hc->ep_type == DWC_OTG_EP_TYPE_ISOC) ++ && hcd->core_if->dma_enable) { ++ qtd->complete_split = 0; ++ qtd->isoc_split_offset = 0; ++ if (++qtd->isoc_frame_index == qtd->urb->packet_count) { ++ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE); ++ } ++ else ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS); ++ goto handle_nyet_done; ++ } ++ ++ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR || ++ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) { ++ int frnum = dwc_otg_hcd_get_frame_number(hcd); ++ ++ // With the FIQ running we only ever see the failed NYET ++ if (dwc_full_frame_num(frnum) != ++ dwc_full_frame_num(hc->qh->sched_frame) || ++ fiq_fsm_enable) { ++ /* ++ * No longer in the same full speed frame. ++ * Treat this as a transaction error. ++ */ ++#if 0 ++ /** @todo Fix system performance so this can ++ * be treated as an error. Right now complete ++ * splits cannot be scheduled precisely enough ++ * due to other system activity, so this error ++ * occurs regularly in Slave mode. ++ */ ++ qtd->error_count++; ++#endif ++ qtd->complete_split = 0; ++ halt_channel(hcd, hc, qtd, ++ DWC_OTG_HC_XFER_XACT_ERR); ++ /** @todo add support for isoc release */ ++ goto handle_nyet_done; ++ } ++ } ++ ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NYET); ++ goto handle_nyet_done; ++ } ++ ++ hc->qh->ping_state = 1; ++ qtd->error_count = 0; ++ ++ update_urb_state_xfer_intr(hc, hc_regs, qtd->urb, qtd, ++ DWC_OTG_HC_XFER_NYET); ++ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd); ++ ++ /* ++ * Halt the channel and re-start the transfer so the PING ++ * protocol will start. ++ */ ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NYET); ++ ++handle_nyet_done: ++ disable_hc_int(hc_regs, nyet); ++ return 1; ++} ++ ++/** ++ * Handles a host channel babble interrupt. This handler may be called in ++ * either DMA mode or Slave mode. ++ */ ++static int32_t handle_hc_babble_intr(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: " ++ "Babble Error--\n", hc->hc_num); ++ ++ if (hcd->core_if->dma_desc_enable) { ++ dwc_otg_hcd_complete_xfer_ddma(hcd, hc, hc_regs, ++ DWC_OTG_HC_XFER_BABBLE_ERR); ++ goto handle_babble_done; ++ } ++ ++ if (hc->ep_type != DWC_OTG_EP_TYPE_ISOC) { ++ hcd->fops->complete(hcd, qtd->urb->priv, ++ qtd->urb, -DWC_E_OVERFLOW); ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_BABBLE_ERR); ++ } else { ++ dwc_otg_halt_status_e halt_status; ++ halt_status = update_isoc_urb_state(hcd, hc, hc_regs, qtd, ++ DWC_OTG_HC_XFER_BABBLE_ERR); ++ halt_channel(hcd, hc, qtd, halt_status); ++ } ++ ++handle_babble_done: ++ disable_hc_int(hc_regs, bblerr); ++ return 1; ++} ++ ++/** ++ * Handles a host channel AHB error interrupt. This handler is only called in ++ * DMA mode. ++ */ ++static int32_t handle_hc_ahberr_intr(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ hcchar_data_t hcchar; ++ hcsplt_data_t hcsplt; ++ hctsiz_data_t hctsiz; ++ uint32_t hcdma; ++ char *pipetype, *speed; ++ ++ dwc_otg_hcd_urb_t *urb = qtd->urb; ++ ++ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: " ++ "AHB Error--\n", hc->hc_num); ++ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ hcsplt.d32 = DWC_READ_REG32(&hc_regs->hcsplt); ++ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz); ++ hcdma = DWC_READ_REG32(&hc_regs->hcdma); ++ ++ DWC_ERROR("AHB ERROR, Channel %d\n", hc->hc_num); ++ DWC_ERROR(" hcchar 0x%08x, hcsplt 0x%08x\n", hcchar.d32, hcsplt.d32); ++ DWC_ERROR(" hctsiz 0x%08x, hcdma 0x%08x\n", hctsiz.d32, hcdma); ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD URB Enqueue\n"); ++ DWC_ERROR(" Device address: %d\n", ++ dwc_otg_hcd_get_dev_addr(&urb->pipe_info)); ++ DWC_ERROR(" Endpoint: %d, %s\n", ++ dwc_otg_hcd_get_ep_num(&urb->pipe_info), ++ (dwc_otg_hcd_is_pipe_in(&urb->pipe_info) ? "IN" : "OUT")); ++ ++ switch (dwc_otg_hcd_get_pipe_type(&urb->pipe_info)) { ++ case UE_CONTROL: ++ pipetype = "CONTROL"; ++ break; ++ case UE_BULK: ++ pipetype = "BULK"; ++ break; ++ case UE_INTERRUPT: ++ pipetype = "INTERRUPT"; ++ break; ++ case UE_ISOCHRONOUS: ++ pipetype = "ISOCHRONOUS"; ++ break; ++ default: ++ pipetype = "UNKNOWN"; ++ break; ++ } ++ ++ DWC_ERROR(" Endpoint type: %s\n", pipetype); ++ ++ switch (hc->speed) { ++ case DWC_OTG_EP_SPEED_HIGH: ++ speed = "HIGH"; ++ break; ++ case DWC_OTG_EP_SPEED_FULL: ++ speed = "FULL"; ++ break; ++ case DWC_OTG_EP_SPEED_LOW: ++ speed = "LOW"; ++ break; ++ default: ++ speed = "UNKNOWN"; ++ break; ++ }; ++ ++ DWC_ERROR(" Speed: %s\n", speed); ++ ++ DWC_ERROR(" Max packet size: %d\n", ++ dwc_otg_hcd_get_mps(&urb->pipe_info)); ++ DWC_ERROR(" Data buffer length: %d\n", urb->length); ++ DWC_ERROR(" Transfer buffer: %p, Transfer DMA: %p\n", ++ urb->buf, (void *)urb->dma); ++ DWC_ERROR(" Setup buffer: %p, Setup DMA: %p\n", ++ urb->setup_packet, (void *)urb->setup_dma); ++ DWC_ERROR(" Interval: %d\n", urb->interval); ++ ++ /* Core haltes the channel for Descriptor DMA mode */ ++ if (hcd->core_if->dma_desc_enable) { ++ dwc_otg_hcd_complete_xfer_ddma(hcd, hc, hc_regs, ++ DWC_OTG_HC_XFER_AHB_ERR); ++ goto handle_ahberr_done; ++ } ++ ++ hcd->fops->complete(hcd, urb->priv, urb, -DWC_E_IO); ++ ++ /* ++ * Force a channel halt. Don't call halt_channel because that won't ++ * write to the HCCHARn register in DMA mode to force the halt. ++ */ ++ dwc_otg_hc_halt(hcd->core_if, hc, DWC_OTG_HC_XFER_AHB_ERR); ++handle_ahberr_done: ++ disable_hc_int(hc_regs, ahberr); ++ return 1; ++} ++ ++/** ++ * Handles a host channel transaction error interrupt. This handler may be ++ * called in either DMA mode or Slave mode. ++ */ ++static int32_t handle_hc_xacterr_intr(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: " ++ "Transaction Error--\n", hc->hc_num); ++ ++ if (hcd->core_if->dma_desc_enable) { ++ dwc_otg_hcd_complete_xfer_ddma(hcd, hc, hc_regs, ++ DWC_OTG_HC_XFER_XACT_ERR); ++ goto handle_xacterr_done; ++ } ++ ++ switch (dwc_otg_hcd_get_pipe_type(&qtd->urb->pipe_info)) { ++ case UE_CONTROL: ++ case UE_BULK: ++ qtd->error_count++; ++ if (!hc->qh->ping_state) { ++ ++ update_urb_state_xfer_intr(hc, hc_regs, ++ qtd->urb, qtd, ++ DWC_OTG_HC_XFER_XACT_ERR); ++ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd); ++ if (!hc->ep_is_in && hc->speed == DWC_OTG_EP_SPEED_HIGH) { ++ hc->qh->ping_state = 1; ++ } ++ } ++ ++ /* ++ * Halt the channel so the transfer can be re-started from ++ * the appropriate point or the PING protocol will start. ++ */ ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_XACT_ERR); ++ break; ++ case UE_INTERRUPT: ++ qtd->error_count++; ++ if (hc->do_split && hc->complete_split) { ++ qtd->complete_split = 0; ++ } ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_XACT_ERR); ++ break; ++ case UE_ISOCHRONOUS: ++ { ++ dwc_otg_halt_status_e halt_status; ++ halt_status = ++ update_isoc_urb_state(hcd, hc, hc_regs, qtd, ++ DWC_OTG_HC_XFER_XACT_ERR); ++ ++ halt_channel(hcd, hc, qtd, halt_status); ++ } ++ break; ++ } ++handle_xacterr_done: ++ disable_hc_int(hc_regs, xacterr); ++ ++ return 1; ++} ++ ++/** ++ * Handles a host channel frame overrun interrupt. This handler may be called ++ * in either DMA mode or Slave mode. ++ */ ++static int32_t handle_hc_frmovrun_intr(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: " ++ "Frame Overrun--\n", hc->hc_num); ++ ++ switch (dwc_otg_hcd_get_pipe_type(&qtd->urb->pipe_info)) { ++ case UE_CONTROL: ++ case UE_BULK: ++ break; ++ case UE_INTERRUPT: ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_FRAME_OVERRUN); ++ break; ++ case UE_ISOCHRONOUS: ++ { ++ dwc_otg_halt_status_e halt_status; ++ halt_status = ++ update_isoc_urb_state(hcd, hc, hc_regs, qtd, ++ DWC_OTG_HC_XFER_FRAME_OVERRUN); ++ ++ halt_channel(hcd, hc, qtd, halt_status); ++ } ++ break; ++ } ++ ++ disable_hc_int(hc_regs, frmovrun); ++ ++ return 1; ++} ++ ++/** ++ * Handles a host channel data toggle error interrupt. This handler may be ++ * called in either DMA mode or Slave mode. ++ */ ++static int32_t handle_hc_datatglerr_intr(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: " ++ "Data Toggle Error on %s transfer--\n", ++ hc->hc_num, (hc->ep_is_in ? "IN" : "OUT")); ++ ++ /* Data toggles on split transactions cause the hc to halt. ++ * restart transfer */ ++ if(hc->qh->do_split) ++ { ++ qtd->error_count++; ++ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd); ++ update_urb_state_xfer_intr(hc, hc_regs, ++ qtd->urb, qtd, DWC_OTG_HC_XFER_XACT_ERR); ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_XACT_ERR); ++ } else if (hc->ep_is_in) { ++ /* An unmasked data toggle error on a non-split DMA transaction is ++ * for the sole purpose of resetting error counts. Disable other ++ * interrupts unmasked for the same reason. ++ */ ++ if(hcd->core_if->dma_enable) { ++ disable_hc_int(hc_regs, ack); ++ disable_hc_int(hc_regs, nak); ++ } ++ qtd->error_count = 0; ++ } ++ ++ disable_hc_int(hc_regs, datatglerr); ++ ++ return 1; ++} ++ ++#ifdef DEBUG ++/** ++ * This function is for debug only. It checks that a valid halt status is set ++ * and that HCCHARn.chdis is clear. If there's a problem, corrective action is ++ * taken and a warning is issued. ++ * @return 1 if halt status is ok, 0 otherwise. ++ */ ++static inline int halt_status_ok(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ hcchar_data_t hcchar; ++ hctsiz_data_t hctsiz; ++ hcint_data_t hcint; ++ hcintmsk_data_t hcintmsk; ++ hcsplt_data_t hcsplt; ++ ++ if (hc->halt_status == DWC_OTG_HC_XFER_NO_HALT_STATUS) { ++ /* ++ * This code is here only as a check. This condition should ++ * never happen. Ignore the halt if it does occur. ++ */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ hctsiz.d32 = DWC_READ_REG32(&hc_regs->hctsiz); ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ hcintmsk.d32 = DWC_READ_REG32(&hc_regs->hcintmsk); ++ hcsplt.d32 = DWC_READ_REG32(&hc_regs->hcsplt); ++ DWC_WARN ++ ("%s: hc->halt_status == DWC_OTG_HC_XFER_NO_HALT_STATUS, " ++ "channel %d, hcchar 0x%08x, hctsiz 0x%08x, " ++ "hcint 0x%08x, hcintmsk 0x%08x, " ++ "hcsplt 0x%08x, qtd->complete_split %d\n", __func__, ++ hc->hc_num, hcchar.d32, hctsiz.d32, hcint.d32, ++ hcintmsk.d32, hcsplt.d32, qtd->complete_split); ++ ++ DWC_WARN("%s: no halt status, channel %d, ignoring interrupt\n", ++ __func__, hc->hc_num); ++ DWC_WARN("\n"); ++ clear_hc_int(hc_regs, chhltd); ++ return 0; ++ } ++ ++ /* ++ * This code is here only as a check. hcchar.chdis should ++ * never be set when the halt interrupt occurs. Halt the ++ * channel again if it does occur. ++ */ ++ hcchar.d32 = DWC_READ_REG32(&hc_regs->hcchar); ++ if (hcchar.b.chdis) { ++ DWC_WARN("%s: hcchar.chdis set unexpectedly, " ++ "hcchar 0x%08x, trying to halt again\n", ++ __func__, hcchar.d32); ++ clear_hc_int(hc_regs, chhltd); ++ hc->halt_pending = 0; ++ halt_channel(hcd, hc, qtd, hc->halt_status); ++ return 0; ++ } ++ ++ return 1; ++} ++#endif ++ ++/** ++ * Handles a host Channel Halted interrupt in DMA mode. This handler ++ * determines the reason the channel halted and proceeds accordingly. ++ */ ++static void handle_hc_chhltd_intr_dma(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ int out_nak_enh = 0; ++ hcint_data_t hcint; ++ hcintmsk_data_t hcintmsk; ++ /* For core with OUT NAK enhancement, the flow for high- ++ * speed CONTROL/BULK OUT is handled a little differently. ++ */ ++ if (hcd->core_if->snpsid >= OTG_CORE_REV_2_71a) { ++ if (hc->speed == DWC_OTG_EP_SPEED_HIGH && !hc->ep_is_in && ++ (hc->ep_type == DWC_OTG_EP_TYPE_CONTROL || ++ hc->ep_type == DWC_OTG_EP_TYPE_BULK)) { ++ out_nak_enh = 1; ++ } ++ } ++ ++ if (hc->halt_status == DWC_OTG_HC_XFER_URB_DEQUEUE || ++ (hc->halt_status == DWC_OTG_HC_XFER_AHB_ERR ++ && !hcd->core_if->dma_desc_enable)) { ++ /* ++ * Just release the channel. A dequeue can happen on a ++ * transfer timeout. In the case of an AHB Error, the channel ++ * was forced to halt because there's no way to gracefully ++ * recover. ++ */ ++ if (hcd->core_if->dma_desc_enable) ++ dwc_otg_hcd_complete_xfer_ddma(hcd, hc, hc_regs, ++ hc->halt_status); ++ else ++ release_channel(hcd, hc, qtd, hc->halt_status); ++ return; ++ } ++ ++ /* Read the HCINTn register to determine the cause for the halt. */ ++ ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ hcintmsk.d32 = DWC_READ_REG32(&hc_regs->hcintmsk); ++ ++ if (hcint.b.xfercomp) { ++ /** @todo This is here because of a possible hardware bug. Spec ++ * says that on SPLIT-ISOC OUT transfers in DMA mode that a HALT ++ * interrupt w/ACK bit set should occur, but I only see the ++ * XFERCOMP bit, even with it masked out. This is a workaround ++ * for that behavior. Should fix this when hardware is fixed. ++ */ ++ if (hc->ep_type == DWC_OTG_EP_TYPE_ISOC && !hc->ep_is_in) { ++ handle_hc_ack_intr(hcd, hc, hc_regs, qtd); ++ } ++ handle_hc_xfercomp_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.stall) { ++ handle_hc_stall_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.xacterr && !hcd->core_if->dma_desc_enable) { ++ if (out_nak_enh) { ++ if (hcint.b.nyet || hcint.b.nak || hcint.b.ack) { ++ DWC_DEBUGPL(DBG_HCD, "XactErr with NYET/NAK/ACK\n"); ++ qtd->error_count = 0; ++ } else { ++ DWC_DEBUGPL(DBG_HCD, "XactErr without NYET/NAK/ACK\n"); ++ } ++ } ++ ++ /* ++ * Must handle xacterr before nak or ack. Could get a xacterr ++ * at the same time as either of these on a BULK/CONTROL OUT ++ * that started with a PING. The xacterr takes precedence. ++ */ ++ handle_hc_xacterr_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.xcs_xact && hcd->core_if->dma_desc_enable) { ++ handle_hc_xacterr_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.ahberr && hcd->core_if->dma_desc_enable) { ++ handle_hc_ahberr_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.bblerr) { ++ handle_hc_babble_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.frmovrun) { ++ handle_hc_frmovrun_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.datatglerr) { ++ handle_hc_datatglerr_intr(hcd, hc, hc_regs, qtd); ++ } else if (!out_nak_enh) { ++ if (hcint.b.nyet) { ++ /* ++ * Must handle nyet before nak or ack. Could get a nyet at the ++ * same time as either of those on a BULK/CONTROL OUT that ++ * started with a PING. The nyet takes precedence. ++ */ ++ handle_hc_nyet_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.nak && !hcintmsk.b.nak) { ++ /* ++ * If nak is not masked, it's because a non-split IN transfer ++ * is in an error state. In that case, the nak is handled by ++ * the nak interrupt handler, not here. Handle nak here for ++ * BULK/CONTROL OUT transfers, which halt on a NAK to allow ++ * rewinding the buffer pointer. ++ */ ++ handle_hc_nak_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.ack && !hcintmsk.b.ack) { ++ /* ++ * If ack is not masked, it's because a non-split IN transfer ++ * is in an error state. In that case, the ack is handled by ++ * the ack interrupt handler, not here. Handle ack here for ++ * split transfers. Start splits halt on ACK. ++ */ ++ handle_hc_ack_intr(hcd, hc, hc_regs, qtd); ++ } else { ++ if (hc->ep_type == DWC_OTG_EP_TYPE_INTR || ++ hc->ep_type == DWC_OTG_EP_TYPE_ISOC) { ++ /* ++ * A periodic transfer halted with no other channel ++ * interrupts set. Assume it was halted by the core ++ * because it could not be completed in its scheduled ++ * (micro)frame. ++ */ ++#ifdef DEBUG ++ DWC_PRINTF ++ ("%s: Halt channel %d (assume incomplete periodic transfer)\n", ++ __func__, hc->hc_num); ++#endif ++ halt_channel(hcd, hc, qtd, ++ DWC_OTG_HC_XFER_PERIODIC_INCOMPLETE); ++ } else { ++ DWC_ERROR ++ ("%s: Channel %d, DMA Mode -- ChHltd set, but reason " ++ "for halting is unknown, hcint 0x%08x, intsts 0x%08x\n", ++ __func__, hc->hc_num, hcint.d32, ++ DWC_READ_REG32(&hcd-> ++ core_if->core_global_regs-> ++ gintsts)); ++ /* Failthrough: use 3-strikes rule */ ++ qtd->error_count++; ++ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd); ++ update_urb_state_xfer_intr(hc, hc_regs, ++ qtd->urb, qtd, DWC_OTG_HC_XFER_XACT_ERR); ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_XACT_ERR); ++ } ++ ++ } ++ } else { ++ DWC_PRINTF("NYET/NAK/ACK/other in non-error case, 0x%08x\n", ++ hcint.d32); ++ /* Failthrough: use 3-strikes rule */ ++ qtd->error_count++; ++ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd); ++ update_urb_state_xfer_intr(hc, hc_regs, ++ qtd->urb, qtd, DWC_OTG_HC_XFER_XACT_ERR); ++ halt_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_XACT_ERR); ++ } ++} ++ ++/** ++ * Handles a host channel Channel Halted interrupt. ++ * ++ * In slave mode, this handler is called only when the driver specifically ++ * requests a halt. This occurs during handling other host channel interrupts ++ * (e.g. nak, xacterr, stall, nyet, etc.). ++ * ++ * In DMA mode, this is the interrupt that occurs when the core has finished ++ * processing a transfer on a channel. Other host channel interrupts (except ++ * ahberr) are disabled in DMA mode. ++ */ ++static int32_t handle_hc_chhltd_intr(dwc_otg_hcd_t * hcd, ++ dwc_hc_t * hc, ++ dwc_otg_hc_regs_t * hc_regs, ++ dwc_otg_qtd_t * qtd) ++{ ++ DWC_DEBUGPL(DBG_HCDI, "--Host Channel %d Interrupt: " ++ "Channel Halted--\n", hc->hc_num); ++ ++ if (hcd->core_if->dma_enable) { ++ handle_hc_chhltd_intr_dma(hcd, hc, hc_regs, qtd); ++ } else { ++#ifdef DEBUG ++ if (!halt_status_ok(hcd, hc, hc_regs, qtd)) { ++ return 1; ++ } ++#endif ++ release_channel(hcd, hc, qtd, hc->halt_status); ++ } ++ ++ return 1; ++} ++ ++ ++/** ++ * dwc_otg_fiq_unmangle_isoc() - Update the iso_frame_desc structure on ++ * FIQ transfer completion ++ * @hcd: Pointer to dwc_otg_hcd struct ++ * @num: Host channel number ++ * ++ * 1. Un-mangle the status as recorded in each iso_frame_desc status ++ * 2. Copy it from the dwc_otg_urb into the real URB ++ */ ++void dwc_otg_fiq_unmangle_isoc(dwc_otg_hcd_t *hcd, dwc_otg_qh_t *qh, dwc_otg_qtd_t *qtd, uint32_t num) ++{ ++ struct dwc_otg_hcd_urb *dwc_urb = qtd->urb; ++ int nr_frames = dwc_urb->packet_count; ++ int i; ++ hcint_data_t frame_hcint; ++ ++ for (i = 0; i < nr_frames; i++) { ++ frame_hcint.d32 = dwc_urb->iso_descs[i].status; ++ if (frame_hcint.b.xfercomp) { ++ dwc_urb->iso_descs[i].status = 0; ++ dwc_urb->actual_length += dwc_urb->iso_descs[i].actual_length; ++ } else if (frame_hcint.b.frmovrun) { ++ if (qh->ep_is_in) ++ dwc_urb->iso_descs[i].status = -DWC_E_NO_STREAM_RES; ++ else ++ dwc_urb->iso_descs[i].status = -DWC_E_COMMUNICATION; ++ dwc_urb->error_count++; ++ dwc_urb->iso_descs[i].actual_length = 0; ++ } else if (frame_hcint.b.xacterr) { ++ dwc_urb->iso_descs[i].status = -DWC_E_PROTOCOL; ++ dwc_urb->error_count++; ++ dwc_urb->iso_descs[i].actual_length = 0; ++ } else if (frame_hcint.b.bblerr) { ++ dwc_urb->iso_descs[i].status = -DWC_E_OVERFLOW; ++ dwc_urb->error_count++; ++ dwc_urb->iso_descs[i].actual_length = 0; ++ } else { ++ /* Something went wrong */ ++ dwc_urb->iso_descs[i].status = -1; ++ dwc_urb->iso_descs[i].actual_length = 0; ++ dwc_urb->error_count++; ++ } ++ } ++ qh->sched_frame = dwc_frame_num_inc(qh->sched_frame, qh->interval * (nr_frames - 1)); ++ ++ //printk_ratelimited(KERN_INFO "%s: HS isochronous of %d/%d frames with %d errors complete\n", ++ // __FUNCTION__, i, dwc_urb->packet_count, dwc_urb->error_count); ++} ++ ++/** ++ * dwc_otg_fiq_unsetup_per_dma() - Remove data from bounce buffers for split transactions ++ * @hcd: Pointer to dwc_otg_hcd struct ++ * @num: Host channel number ++ * ++ * Copies data from the FIQ bounce buffers into the URB's transfer buffer. Does not modify URB state. ++ * Returns total length of data or -1 if the buffers were not used. ++ * ++ */ ++int dwc_otg_fiq_unsetup_per_dma(dwc_otg_hcd_t *hcd, dwc_otg_qh_t *qh, dwc_otg_qtd_t *qtd, uint32_t num) ++{ ++ dwc_hc_t *hc = qh->channel; ++ struct fiq_dma_blob *blob = hcd->fiq_dmab; ++ struct fiq_channel_state *st = &hcd->fiq_state->channel[num]; ++ uint8_t *ptr = NULL; ++ int index = 0, len = 0; ++ int i = 0; ++ if (hc->ep_is_in) { ++ /* Copy data out of the DMA bounce buffers to the URB's buffer. ++ * The align_buf is ignored as this is ignored on FSM enqueue. */ ++ ptr = qtd->urb->buf; ++ if (qh->ep_type == UE_ISOCHRONOUS) { ++ /* Isoc IN transactions - grab the offset of the iso_frame_desc into the URB transfer buffer */ ++ index = qtd->isoc_frame_index; ++ ptr += qtd->urb->iso_descs[index].offset; ++ } else { ++ /* Need to increment by actual_length for interrupt IN */ ++ ptr += qtd->urb->actual_length; ++ } ++ ++ for (i = 0; i < st->dma_info.index; i++) { ++ len += st->dma_info.slot_len[i]; ++ dwc_memcpy(ptr, &blob->channel[num].index[i].buf[0], st->dma_info.slot_len[i]); ++ ptr += st->dma_info.slot_len[i]; ++ } ++ return len; ++ } else { ++ /* OUT endpoints - nothing to do. */ ++ return -1; ++ } ++ ++} ++/** ++ * dwc_otg_hcd_handle_hc_fsm() - handle an unmasked channel interrupt ++ * from a channel handled in the FIQ ++ * @hcd: Pointer to dwc_otg_hcd struct ++ * @num: Host channel number ++ * ++ * If a host channel interrupt was received by the IRQ and this was a channel ++ * used by the FIQ, the execution flow for transfer completion is substantially ++ * different from the normal (messy) path. This function and its friends handles ++ * channel cleanup and transaction completion from a FIQ transaction. ++ */ ++void dwc_otg_hcd_handle_hc_fsm(dwc_otg_hcd_t *hcd, uint32_t num) ++{ ++ struct fiq_channel_state *st = &hcd->fiq_state->channel[num]; ++ dwc_hc_t *hc = hcd->hc_ptr_array[num]; ++ dwc_otg_qtd_t *qtd; ++ dwc_otg_hc_regs_t *hc_regs = hcd->core_if->host_if->hc_regs[num]; ++ hcint_data_t hcint = hcd->fiq_state->channel[num].hcint_copy; ++ hctsiz_data_t hctsiz = hcd->fiq_state->channel[num].hctsiz_copy; ++ int hostchannels = 0; ++ fiq_print(FIQDBG_INT, hcd->fiq_state, "OUT %01d %01d ", num , st->fsm); ++ ++ hostchannels = hcd->available_host_channels; ++ if (hc->halt_pending) { ++ /* Dequeue: The FIQ was allowed to complete the transfer but state has been cleared. */ ++ if (hc->qh && st->fsm == FIQ_NP_SPLIT_DONE && ++ hcint.b.xfercomp && hc->qh->ep_type == UE_BULK) { ++ if (hctsiz.b.pid == DWC_HCTSIZ_DATA0) { ++ hc->qh->data_toggle = DWC_OTG_HC_PID_DATA1; ++ } else { ++ hc->qh->data_toggle = DWC_OTG_HC_PID_DATA0; ++ } ++ } ++ release_channel(hcd, hc, NULL, hc->halt_status); ++ return; ++ } ++ ++ qtd = DWC_CIRCLEQ_FIRST(&hc->qh->qtd_list); ++ switch (st->fsm) { ++ case FIQ_TEST: ++ break; ++ ++ case FIQ_DEQUEUE_ISSUED: ++ /* Handled above, but keep for posterity */ ++ release_channel(hcd, hc, NULL, hc->halt_status); ++ break; ++ ++ case FIQ_NP_SPLIT_DONE: ++ /* Nonperiodic transaction complete. */ ++ if (!hc->ep_is_in) { ++ qtd->ssplit_out_xfer_count = hc->xfer_len; ++ } ++ if (hcint.b.xfercomp) { ++ handle_hc_xfercomp_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.nak) { ++ handle_hc_nak_intr(hcd, hc, hc_regs, qtd); ++ } else { ++ DWC_WARN("Unexpected IRQ state on FSM transaction:" ++ "dev_addr=%d ep=%d fsm=%d, hcint=0x%08x\n", ++ hc->dev_addr, hc->ep_num, st->fsm, hcint.d32); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS); ++ } ++ break; ++ ++ case FIQ_NP_SPLIT_HS_ABORTED: ++ /* A HS abort is a 3-strikes on the HS bus at any point in the transaction. ++ * Normally a CLEAR_TT_BUFFER hub command would be required: we can't do that ++ * because there's no guarantee which order a non-periodic split happened in. ++ * We could end up clearing a perfectly good transaction out of the buffer. ++ */ ++ if (hcint.b.xacterr) { ++ qtd->error_count += st->nr_errors; ++ handle_hc_xacterr_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.ahberr) { ++ handle_hc_ahberr_intr(hcd, hc, hc_regs, qtd); ++ } else { ++ DWC_WARN("Unexpected IRQ state on FSM transaction:" ++ "dev_addr=%d ep=%d fsm=%d, hcint=0x%08x\n", ++ hc->dev_addr, hc->ep_num, st->fsm, hcint.d32); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS); ++ } ++ break; ++ ++ case FIQ_NP_SPLIT_LS_ABORTED: ++ /* A few cases can cause this - either an unknown state on a SSPLIT or ++ * STALL/data toggle error response on a CSPLIT */ ++ if (hcint.b.stall) { ++ handle_hc_stall_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.datatglerr) { ++ handle_hc_datatglerr_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.bblerr) { ++ handle_hc_babble_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.ahberr) { ++ handle_hc_ahberr_intr(hcd, hc, hc_regs, qtd); ++ } else { ++ DWC_WARN("Unexpected IRQ state on FSM transaction:" ++ "dev_addr=%d ep=%d fsm=%d, hcint=0x%08x\n", ++ hc->dev_addr, hc->ep_num, st->fsm, hcint.d32); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS); ++ } ++ break; ++ ++ case FIQ_PER_SPLIT_DONE: ++ /* Isoc IN or Interrupt IN/OUT */ ++ ++ /* Flow control here is different from the normal execution by the driver. ++ * We need to completely ignore most of the driver's method of handling ++ * split transactions and do it ourselves. ++ */ ++ if (hc->ep_type == UE_INTERRUPT) { ++ if (hcint.b.nak) { ++ handle_hc_nak_intr(hcd, hc, hc_regs, qtd); ++ } else if (hc->ep_is_in) { ++ int len; ++ len = dwc_otg_fiq_unsetup_per_dma(hcd, hc->qh, qtd, num); ++ //printk(KERN_NOTICE "FIQ Transaction: hc=%d len=%d urb_len = %d\n", num, len, qtd->urb->length); ++ qtd->urb->actual_length += len; ++ if (qtd->urb->actual_length >= qtd->urb->length) { ++ qtd->urb->status = 0; ++ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, qtd->urb->status); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE); ++ } else { ++ /* Interrupt transfer not complete yet - is it a short read? */ ++ if (len < hc->max_packet) { ++ /* Interrupt transaction complete */ ++ qtd->urb->status = 0; ++ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, qtd->urb->status); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE); ++ } else { ++ /* Further transactions required */ ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_COMPLETE); ++ } ++ } ++ } else { ++ /* Interrupt OUT complete. */ ++ dwc_otg_hcd_save_data_toggle(hc, hc_regs, qtd); ++ qtd->urb->actual_length += hc->xfer_len; ++ if (qtd->urb->actual_length >= qtd->urb->length) { ++ qtd->urb->status = 0; ++ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, qtd->urb->status); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE); ++ } else { ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_COMPLETE); ++ } ++ } ++ } else { ++ /* ISOC IN complete. */ ++ struct dwc_otg_hcd_iso_packet_desc *frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index]; ++ int len = 0; ++ /* Record errors, update qtd. */ ++ if (st->nr_errors) { ++ frame_desc->actual_length = 0; ++ frame_desc->status = -DWC_E_PROTOCOL; ++ } else { ++ frame_desc->status = 0; ++ /* Unswizzle dma */ ++ len = dwc_otg_fiq_unsetup_per_dma(hcd, hc->qh, qtd, num); ++ frame_desc->actual_length = len; ++ } ++ qtd->isoc_frame_index++; ++ if (qtd->isoc_frame_index == qtd->urb->packet_count) { ++ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE); ++ } else { ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_COMPLETE); ++ } ++ } ++ break; ++ ++ case FIQ_PER_ISO_OUT_DONE: { ++ struct dwc_otg_hcd_iso_packet_desc *frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index]; ++ /* Record errors, update qtd. */ ++ if (st->nr_errors) { ++ frame_desc->actual_length = 0; ++ frame_desc->status = -DWC_E_PROTOCOL; ++ } else { ++ frame_desc->status = 0; ++ frame_desc->actual_length = frame_desc->length; ++ } ++ qtd->isoc_frame_index++; ++ qtd->isoc_split_offset = 0; ++ if (qtd->isoc_frame_index == qtd->urb->packet_count) { ++ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE); ++ } else { ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_COMPLETE); ++ } ++ } ++ break; ++ ++ case FIQ_PER_SPLIT_NYET_ABORTED: ++ /* Doh. lost the data. */ ++ printk_ratelimited(KERN_INFO "Transfer to device %d endpoint 0x%x frame %d failed " ++ "- FIQ reported NYET. Data may have been lost.\n", ++ hc->dev_addr, hc->ep_num, dwc_otg_hcd_get_frame_number(hcd) >> 3); ++ if (hc->ep_type == UE_ISOCHRONOUS) { ++ struct dwc_otg_hcd_iso_packet_desc *frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index]; ++ /* Record errors, update qtd. */ ++ frame_desc->actual_length = 0; ++ frame_desc->status = -DWC_E_PROTOCOL; ++ qtd->isoc_frame_index++; ++ qtd->isoc_split_offset = 0; ++ if (qtd->isoc_frame_index == qtd->urb->packet_count) { ++ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE); ++ } else { ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_COMPLETE); ++ } ++ } else { ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS); ++ } ++ break; ++ ++ case FIQ_HS_ISOC_DONE: ++ /* The FIQ has performed a whole pile of isochronous transactions. ++ * The status is recorded as the interrupt state should the transaction ++ * fail. ++ */ ++ dwc_otg_fiq_unmangle_isoc(hcd, hc->qh, qtd, num); ++ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE); ++ break; ++ ++ case FIQ_PER_SPLIT_LS_ABORTED: ++ if (hcint.b.xacterr) { ++ /* Hub has responded with an ERR packet. Device ++ * has been unplugged or the port has been disabled. ++ * TODO: need to issue a reset to the hub port. */ ++ qtd->error_count += 3; ++ handle_hc_xacterr_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.stall) { ++ handle_hc_stall_intr(hcd, hc, hc_regs, qtd); ++ } else if (hcint.b.bblerr) { ++ handle_hc_babble_intr(hcd, hc, hc_regs, qtd); ++ } else { ++ printk_ratelimited(KERN_INFO "Transfer to device %d endpoint 0x%x failed " ++ "- FIQ reported FSM=%d. Data may have been lost.\n", ++ st->fsm, hc->dev_addr, hc->ep_num); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS); ++ } ++ break; ++ ++ case FIQ_PER_SPLIT_HS_ABORTED: ++ /* Either the SSPLIT phase suffered transaction errors or something ++ * unexpected happened. ++ */ ++ qtd->error_count += 3; ++ handle_hc_xacterr_intr(hcd, hc, hc_regs, qtd); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS); ++ break; ++ ++ case FIQ_PER_SPLIT_TIMEOUT: ++ /* Couldn't complete in the nominated frame */ ++ printk(KERN_INFO "Transfer to device %d endpoint 0x%x frame %d failed " ++ "- FIQ timed out. Data may have been lost.\n", ++ hc->dev_addr, hc->ep_num, dwc_otg_hcd_get_frame_number(hcd) >> 3); ++ if (hc->ep_type == UE_ISOCHRONOUS) { ++ struct dwc_otg_hcd_iso_packet_desc *frame_desc = &qtd->urb->iso_descs[qtd->isoc_frame_index]; ++ /* Record errors, update qtd. */ ++ frame_desc->actual_length = 0; ++ if (hc->ep_is_in) { ++ frame_desc->status = -DWC_E_NO_STREAM_RES; ++ } else { ++ frame_desc->status = -DWC_E_COMMUNICATION; ++ } ++ qtd->isoc_frame_index++; ++ if (qtd->isoc_frame_index == qtd->urb->packet_count) { ++ hcd->fops->complete(hcd, qtd->urb->priv, qtd->urb, 0); ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_URB_COMPLETE); ++ } else { ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_COMPLETE); ++ } ++ } else { ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS); ++ } ++ break; ++ ++ default: ++ DWC_WARN("Unexpected state received on hc=%d fsm=%d on transfer to device %d ep 0x%x", ++ hc->hc_num, st->fsm, hc->dev_addr, hc->ep_num); ++ qtd->error_count++; ++ release_channel(hcd, hc, qtd, DWC_OTG_HC_XFER_NO_HALT_STATUS); ++ } ++ return; ++} ++ ++/** Handles interrupt for a specific Host Channel */ ++int32_t dwc_otg_hcd_handle_hc_n_intr(dwc_otg_hcd_t * dwc_otg_hcd, uint32_t num) ++{ ++ int retval = 0; ++ hcint_data_t hcint; ++ hcintmsk_data_t hcintmsk; ++ dwc_hc_t *hc; ++ dwc_otg_hc_regs_t *hc_regs; ++ dwc_otg_qtd_t *qtd; ++ ++ DWC_DEBUGPL(DBG_HCDV, "--Host Channel Interrupt--, Channel %d\n", num); ++ ++ hc = dwc_otg_hcd->hc_ptr_array[num]; ++ hc_regs = dwc_otg_hcd->core_if->host_if->hc_regs[num]; ++ if(hc->halt_status == DWC_OTG_HC_XFER_URB_DEQUEUE) { ++ /* A dequeue was issued for this transfer. Our QTD has gone away ++ * but in the case of a FIQ transfer, the transfer would have run ++ * to completion. ++ */ ++ if (fiq_fsm_enable && dwc_otg_hcd->fiq_state->channel[num].fsm != FIQ_PASSTHROUGH) { ++ dwc_otg_hcd_handle_hc_fsm(dwc_otg_hcd, num); ++ } else { ++ release_channel(dwc_otg_hcd, hc, NULL, hc->halt_status); ++ } ++ return 1; ++ } ++ qtd = DWC_CIRCLEQ_FIRST(&hc->qh->qtd_list); ++ ++ /* ++ * FSM mode: Check to see if this is a HC interrupt from a channel handled by the FIQ. ++ * Execution path is fundamentally different for the channels after a FIQ has completed ++ * a split transaction. ++ */ ++ if (fiq_fsm_enable) { ++ switch (dwc_otg_hcd->fiq_state->channel[num].fsm) { ++ case FIQ_PASSTHROUGH: ++ break; ++ case FIQ_PASSTHROUGH_ERRORSTATE: ++ /* Hook into the error count */ ++ fiq_print(FIQDBG_ERR, dwc_otg_hcd->fiq_state, "HCDERR%02d", num); ++ if (!dwc_otg_hcd->fiq_state->channel[num].nr_errors) { ++ qtd->error_count = 0; ++ fiq_print(FIQDBG_ERR, dwc_otg_hcd->fiq_state, "RESET "); ++ } ++ break; ++ default: ++ dwc_otg_hcd_handle_hc_fsm(dwc_otg_hcd, num); ++ return 1; ++ } ++ } ++ ++ hcint.d32 = DWC_READ_REG32(&hc_regs->hcint); ++ hcintmsk.d32 = DWC_READ_REG32(&hc_regs->hcintmsk); ++ hcint.d32 = hcint.d32 & hcintmsk.d32; ++ if (!dwc_otg_hcd->core_if->dma_enable) { ++ if (hcint.b.chhltd && hcint.d32 != 0x2) { ++ hcint.b.chhltd = 0; ++ } ++ } ++ ++ if (hcint.b.xfercomp) { ++ retval |= ++ handle_hc_xfercomp_intr(dwc_otg_hcd, hc, hc_regs, qtd); ++ /* ++ * If NYET occurred at same time as Xfer Complete, the NYET is ++ * handled by the Xfer Complete interrupt handler. Don't want ++ * to call the NYET interrupt handler in this case. ++ */ ++ hcint.b.nyet = 0; ++ } ++ if (hcint.b.chhltd) { ++ retval |= handle_hc_chhltd_intr(dwc_otg_hcd, hc, hc_regs, qtd); ++ } ++ if (hcint.b.ahberr) { ++ retval |= handle_hc_ahberr_intr(dwc_otg_hcd, hc, hc_regs, qtd); ++ } ++ if (hcint.b.stall) { ++ retval |= handle_hc_stall_intr(dwc_otg_hcd, hc, hc_regs, qtd); ++ } ++ if (hcint.b.nak) { ++ retval |= handle_hc_nak_intr(dwc_otg_hcd, hc, hc_regs, qtd); ++ } ++ if (hcint.b.ack) { ++ if(!hcint.b.chhltd) ++ retval |= handle_hc_ack_intr(dwc_otg_hcd, hc, hc_regs, qtd); ++ } ++ if (hcint.b.nyet) { ++ retval |= handle_hc_nyet_intr(dwc_otg_hcd, hc, hc_regs, qtd); ++ } ++ if (hcint.b.xacterr) { ++ retval |= handle_hc_xacterr_intr(dwc_otg_hcd, hc, hc_regs, qtd); ++ } ++ if (hcint.b.bblerr) { ++ retval |= handle_hc_babble_intr(dwc_otg_hcd, hc, hc_regs, qtd); ++ } ++ if (hcint.b.frmovrun) { ++ retval |= ++ handle_hc_frmovrun_intr(dwc_otg_hcd, hc, hc_regs, qtd); ++ } ++ if (hcint.b.datatglerr) { ++ retval |= ++ handle_hc_datatglerr_intr(dwc_otg_hcd, hc, hc_regs, qtd); ++ } ++ ++ return retval; ++} ++#endif /* DWC_DEVICE_ONLY */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd_linux.c +@@ -0,0 +1,1086 @@ ++ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd_linux.c $ ++ * $Revision: #20 $ ++ * $Date: 2011/10/26 $ ++ * $Change: 1872981 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++#ifndef DWC_DEVICE_ONLY ++ ++/** ++ * @file ++ * ++ * This file contains the implementation of the HCD. In Linux, the HCD ++ * implements the hc_driver API. ++ */ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#ifdef CONFIG_ARM ++#include ++#endif ++#include ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,35) ++#include <../drivers/usb/core/hcd.h> ++#else ++#include ++#endif ++#include ++ ++#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,30)) ++#define USB_URB_EP_LINKING 1 ++#else ++#define USB_URB_EP_LINKING 0 ++#endif ++ ++#include "dwc_otg_hcd_if.h" ++#include "dwc_otg_dbg.h" ++#include "dwc_otg_driver.h" ++#include "dwc_otg_hcd.h" ++ ++#ifndef __virt_to_bus ++#define __virt_to_bus __virt_to_phys ++#define __bus_to_virt __phys_to_virt ++#define __pfn_to_bus(x) __pfn_to_phys(x) ++#define __bus_to_pfn(x) __phys_to_pfn(x) ++#endif ++ ++extern unsigned char _dwc_otg_fiq_stub, _dwc_otg_fiq_stub_end; ++ ++/** ++ * Gets the endpoint number from a _bEndpointAddress argument. The endpoint is ++ * qualified with its direction (possible 32 endpoints per device). ++ */ ++#define dwc_ep_addr_to_endpoint(_bEndpointAddress_) ((_bEndpointAddress_ & USB_ENDPOINT_NUMBER_MASK) | \ ++ ((_bEndpointAddress_ & USB_DIR_IN) != 0) << 4) ++ ++static const char dwc_otg_hcd_name[] = "dwc_otg_hcd"; ++ ++extern bool fiq_enable; ++ ++/** @name Linux HC Driver API Functions */ ++/** @{ */ ++/* manage i/o requests, device state */ ++static int dwc_otg_urb_enqueue(struct usb_hcd *hcd, ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28) ++ struct usb_host_endpoint *ep, ++#endif ++ struct urb *urb, gfp_t mem_flags); ++ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,30) ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28) ++static int dwc_otg_urb_dequeue(struct usb_hcd *hcd, struct urb *urb); ++#endif ++#else /* kernels at or post 2.6.30 */ ++static int dwc_otg_urb_dequeue(struct usb_hcd *hcd, ++ struct urb *urb, int status); ++#endif /* LINUX_VERSION_CODE < KERNEL_VERSION(2,6,30) */ ++ ++static void endpoint_disable(struct usb_hcd *hcd, struct usb_host_endpoint *ep); ++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,30) ++static void endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep); ++#endif ++static irqreturn_t dwc_otg_hcd_irq(struct usb_hcd *hcd); ++extern int hcd_start(struct usb_hcd *hcd); ++extern void hcd_stop(struct usb_hcd *hcd); ++static int get_frame_number(struct usb_hcd *hcd); ++extern int hub_status_data(struct usb_hcd *hcd, char *buf); ++extern int hub_control(struct usb_hcd *hcd, ++ u16 typeReq, ++ u16 wValue, u16 wIndex, char *buf, u16 wLength); ++ ++struct wrapper_priv_data { ++ dwc_otg_hcd_t *dwc_otg_hcd; ++}; ++ ++/** @} */ ++ ++static struct hc_driver dwc_otg_hc_driver = { ++ ++ .description = dwc_otg_hcd_name, ++ .product_desc = "DWC OTG Controller", ++ .hcd_priv_size = sizeof(struct wrapper_priv_data), ++ ++ .irq = dwc_otg_hcd_irq, ++ ++ .flags = HCD_MEMORY | HCD_DMA | HCD_USB2, ++ ++ //.reset = ++ .start = hcd_start, ++ //.suspend = ++ //.resume = ++ .stop = hcd_stop, ++ ++ .urb_enqueue = dwc_otg_urb_enqueue, ++ .urb_dequeue = dwc_otg_urb_dequeue, ++ .endpoint_disable = endpoint_disable, ++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,30) ++ .endpoint_reset = endpoint_reset, ++#endif ++ .get_frame_number = get_frame_number, ++ ++ .hub_status_data = hub_status_data, ++ .hub_control = hub_control, ++ //.bus_suspend = ++ //.bus_resume = ++}; ++ ++/** Gets the dwc_otg_hcd from a struct usb_hcd */ ++static inline dwc_otg_hcd_t *hcd_to_dwc_otg_hcd(struct usb_hcd *hcd) ++{ ++ struct wrapper_priv_data *p; ++ p = (struct wrapper_priv_data *)(hcd->hcd_priv); ++ return p->dwc_otg_hcd; ++} ++ ++/** Gets the struct usb_hcd that contains a dwc_otg_hcd_t. */ ++static inline struct usb_hcd *dwc_otg_hcd_to_hcd(dwc_otg_hcd_t * dwc_otg_hcd) ++{ ++ return dwc_otg_hcd_get_priv_data(dwc_otg_hcd); ++} ++ ++/** Gets the usb_host_endpoint associated with an URB. */ ++inline struct usb_host_endpoint *dwc_urb_to_endpoint(struct urb *urb) ++{ ++ struct usb_device *dev = urb->dev; ++ int ep_num = usb_pipeendpoint(urb->pipe); ++ ++ if (usb_pipein(urb->pipe)) ++ return dev->ep_in[ep_num]; ++ else ++ return dev->ep_out[ep_num]; ++} ++ ++static int _disconnect(dwc_otg_hcd_t * hcd) ++{ ++ struct usb_hcd *usb_hcd = dwc_otg_hcd_to_hcd(hcd); ++ ++ usb_hcd->self.is_b_host = 0; ++ return 0; ++} ++ ++static int _start(dwc_otg_hcd_t * hcd) ++{ ++ struct usb_hcd *usb_hcd = dwc_otg_hcd_to_hcd(hcd); ++ ++ usb_hcd->self.is_b_host = dwc_otg_hcd_is_b_host(hcd); ++ hcd_start(usb_hcd); ++ ++ return 0; ++} ++ ++static int _hub_info(dwc_otg_hcd_t * hcd, void *urb_handle, uint32_t * hub_addr, ++ uint32_t * port_addr) ++{ ++ struct urb *urb = (struct urb *)urb_handle; ++ struct usb_bus *bus; ++#if 1 //GRAYG - temporary ++ if (NULL == urb_handle) ++ DWC_ERROR("**** %s - NULL URB handle\n", __func__);//GRAYG ++ if (NULL == urb->dev) ++ DWC_ERROR("**** %s - URB has no device\n", __func__);//GRAYG ++ if (NULL == port_addr) ++ DWC_ERROR("**** %s - NULL port_address\n", __func__);//GRAYG ++#endif ++ if (urb->dev->tt) { ++ if (NULL == urb->dev->tt->hub) { ++ DWC_ERROR("**** %s - (URB's transactor has no TT - giving no hub)\n", ++ __func__); //GRAYG ++ //*hub_addr = (u8)usb_pipedevice(urb->pipe); //GRAYG ++ *hub_addr = 0; //GRAYG ++ // we probably shouldn't have a transaction translator if ++ // there's no associated hub? ++ } else { ++ bus = hcd_to_bus(dwc_otg_hcd_to_hcd(hcd)); ++ if (urb->dev->tt->hub == bus->root_hub) ++ *hub_addr = 0; ++ else ++ *hub_addr = urb->dev->tt->hub->devnum; ++ } ++ *port_addr = urb->dev->ttport; ++ } else { ++ *hub_addr = 0; ++ *port_addr = urb->dev->ttport; ++ } ++ return 0; ++} ++ ++static int _speed(dwc_otg_hcd_t * hcd, void *urb_handle) ++{ ++ struct urb *urb = (struct urb *)urb_handle; ++ return urb->dev->speed; ++} ++ ++static int _get_b_hnp_enable(dwc_otg_hcd_t * hcd) ++{ ++ struct usb_hcd *usb_hcd = dwc_otg_hcd_to_hcd(hcd); ++ return usb_hcd->self.b_hnp_enable; ++} ++ ++static void allocate_bus_bandwidth(struct usb_hcd *hcd, uint32_t bw, ++ struct urb *urb) ++{ ++ hcd_to_bus(hcd)->bandwidth_allocated += bw / urb->interval; ++ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { ++ hcd_to_bus(hcd)->bandwidth_isoc_reqs++; ++ } else { ++ hcd_to_bus(hcd)->bandwidth_int_reqs++; ++ } ++} ++ ++static void free_bus_bandwidth(struct usb_hcd *hcd, uint32_t bw, ++ struct urb *urb) ++{ ++ hcd_to_bus(hcd)->bandwidth_allocated -= bw / urb->interval; ++ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { ++ hcd_to_bus(hcd)->bandwidth_isoc_reqs--; ++ } else { ++ hcd_to_bus(hcd)->bandwidth_int_reqs--; ++ } ++} ++ ++/** ++ * Sets the final status of an URB and returns it to the device driver. Any ++ * required cleanup of the URB is performed. The HCD lock should be held on ++ * entry. ++ */ ++static int _complete(dwc_otg_hcd_t * hcd, void *urb_handle, ++ dwc_otg_hcd_urb_t * dwc_otg_urb, int32_t status) ++{ ++ struct urb *urb = (struct urb *)urb_handle; ++ urb_tq_entry_t *new_entry; ++ int rc = 0; ++ if (CHK_DEBUG_LEVEL(DBG_HCDV | DBG_HCD_URB)) { ++ DWC_PRINTF("%s: urb %p, device %d, ep %d %s, status=%d\n", ++ __func__, urb, usb_pipedevice(urb->pipe), ++ usb_pipeendpoint(urb->pipe), ++ usb_pipein(urb->pipe) ? "IN" : "OUT", status); ++ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { ++ int i; ++ for (i = 0; i < urb->number_of_packets; i++) { ++ DWC_PRINTF(" ISO Desc %d status: %d\n", ++ i, urb->iso_frame_desc[i].status); ++ } ++ } ++ } ++ new_entry = DWC_ALLOC_ATOMIC(sizeof(urb_tq_entry_t)); ++ urb->actual_length = dwc_otg_hcd_urb_get_actual_length(dwc_otg_urb); ++ /* Convert status value. */ ++ switch (status) { ++ case -DWC_E_PROTOCOL: ++ status = -EPROTO; ++ break; ++ case -DWC_E_IN_PROGRESS: ++ status = -EINPROGRESS; ++ break; ++ case -DWC_E_PIPE: ++ status = -EPIPE; ++ break; ++ case -DWC_E_IO: ++ status = -EIO; ++ break; ++ case -DWC_E_TIMEOUT: ++ status = -ETIMEDOUT; ++ break; ++ case -DWC_E_OVERFLOW: ++ status = -EOVERFLOW; ++ break; ++ case -DWC_E_SHUTDOWN: ++ status = -ESHUTDOWN; ++ break; ++ default: ++ if (status) { ++ DWC_PRINTF("Uknown urb status %d\n", status); ++ ++ } ++ } ++ ++ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { ++ int i; ++ ++ urb->error_count = dwc_otg_hcd_urb_get_error_count(dwc_otg_urb); ++ urb->actual_length = 0; ++ for (i = 0; i < urb->number_of_packets; ++i) { ++ urb->iso_frame_desc[i].actual_length = ++ dwc_otg_hcd_urb_get_iso_desc_actual_length ++ (dwc_otg_urb, i); ++ urb->actual_length += urb->iso_frame_desc[i].actual_length; ++ urb->iso_frame_desc[i].status = ++ dwc_otg_hcd_urb_get_iso_desc_status(dwc_otg_urb, i); ++ } ++ } ++ ++ urb->status = status; ++ urb->hcpriv = NULL; ++ if (!status) { ++ if ((urb->transfer_flags & URB_SHORT_NOT_OK) && ++ (urb->actual_length < urb->transfer_buffer_length)) { ++ urb->status = -EREMOTEIO; ++ } ++ } ++ ++ if ((usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) || ++ (usb_pipetype(urb->pipe) == PIPE_INTERRUPT)) { ++ struct usb_host_endpoint *ep = dwc_urb_to_endpoint(urb); ++ if (ep) { ++ free_bus_bandwidth(dwc_otg_hcd_to_hcd(hcd), ++ dwc_otg_hcd_get_ep_bandwidth(hcd, ++ ep->hcpriv), ++ urb); ++ } ++ } ++ DWC_FREE(dwc_otg_urb); ++ if (!new_entry) { ++ DWC_ERROR("dwc_otg_hcd: complete: cannot allocate URB TQ entry\n"); ++ urb->status = -EPROTO; ++ /* don't schedule the tasklet - ++ * directly return the packet here with error. */ ++#if USB_URB_EP_LINKING ++ usb_hcd_unlink_urb_from_ep(dwc_otg_hcd_to_hcd(hcd), urb); ++#endif ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28) ++ usb_hcd_giveback_urb(dwc_otg_hcd_to_hcd(hcd), urb); ++#else ++ usb_hcd_giveback_urb(dwc_otg_hcd_to_hcd(hcd), urb, urb->status); ++#endif ++ } else { ++ new_entry->urb = urb; ++#if USB_URB_EP_LINKING ++ rc = usb_hcd_check_unlink_urb(dwc_otg_hcd_to_hcd(hcd), urb, urb->status); ++ if(0 == rc) { ++ usb_hcd_unlink_urb_from_ep(dwc_otg_hcd_to_hcd(hcd), urb); ++ } ++#endif ++ if(0 == rc) { ++ DWC_TAILQ_INSERT_TAIL(&hcd->completed_urb_list, new_entry, ++ urb_tq_entries); ++ DWC_TASK_HI_SCHEDULE(hcd->completion_tasklet); ++ } ++ } ++ return 0; ++} ++ ++static struct dwc_otg_hcd_function_ops hcd_fops = { ++ .start = _start, ++ .disconnect = _disconnect, ++ .hub_info = _hub_info, ++ .speed = _speed, ++ .complete = _complete, ++ .get_b_hnp_enable = _get_b_hnp_enable, ++}; ++ ++#ifdef CONFIG_ARM64 ++ ++static int simfiq_irq = -1; ++ ++void local_fiq_enable(void) ++{ ++ if (simfiq_irq >= 0) ++ enable_irq(simfiq_irq); ++} ++ ++void local_fiq_disable(void) ++{ ++ if (simfiq_irq >= 0) ++ disable_irq(simfiq_irq); ++} ++ ++irqreturn_t fiq_irq_handler(int irq, void *dev_id) ++{ ++ dwc_otg_hcd_t *dwc_otg_hcd = (dwc_otg_hcd_t *)dev_id; ++ ++ if (fiq_fsm_enable) ++ dwc_otg_fiq_fsm(dwc_otg_hcd->fiq_state, dwc_otg_hcd->core_if->core_params->host_channels); ++ else ++ dwc_otg_fiq_nop(dwc_otg_hcd->fiq_state); ++ ++ return IRQ_HANDLED; ++} ++ ++#else ++static struct fiq_handler fh = { ++ .name = "usb_fiq", ++}; ++ ++#endif ++ ++static void hcd_init_fiq(void *cookie) ++{ ++ dwc_otg_device_t *otg_dev = cookie; ++ dwc_otg_hcd_t *dwc_otg_hcd = otg_dev->hcd; ++#ifdef CONFIG_ARM64 ++ int retval = 0; ++ int irq; ++#else ++ struct pt_regs regs; ++ int irq; ++ ++ if (claim_fiq(&fh)) { ++ DWC_ERROR("Can't claim FIQ"); ++ BUG(); ++ } ++ DWC_WARN("FIQ on core %d", smp_processor_id()); ++ DWC_WARN("FIQ ASM at %px length %d", &_dwc_otg_fiq_stub, (int)(&_dwc_otg_fiq_stub_end - &_dwc_otg_fiq_stub)); ++ set_fiq_handler((void *) &_dwc_otg_fiq_stub, &_dwc_otg_fiq_stub_end - &_dwc_otg_fiq_stub); ++ memset(®s,0,sizeof(regs)); ++ ++ regs.ARM_r8 = (long) dwc_otg_hcd->fiq_state; ++ if (fiq_fsm_enable) { ++ regs.ARM_r9 = dwc_otg_hcd->core_if->core_params->host_channels; ++ //regs.ARM_r10 = dwc_otg_hcd->dma; ++ regs.ARM_fp = (long) dwc_otg_fiq_fsm; ++ } else { ++ regs.ARM_fp = (long) dwc_otg_fiq_nop; ++ } ++ ++ regs.ARM_sp = (long) dwc_otg_hcd->fiq_stack + (sizeof(struct fiq_stack) - 4); ++ ++// __show_regs(®s); ++ set_fiq_regs(®s); ++#endif ++ ++ dwc_otg_hcd->fiq_state->dwc_regs_base = otg_dev->os_dep.base; ++ //Set the mphi periph to the required registers ++ dwc_otg_hcd->fiq_state->mphi_regs.base = otg_dev->os_dep.mphi_base; ++ if (otg_dev->os_dep.use_swirq) { ++ dwc_otg_hcd->fiq_state->mphi_regs.swirq_set = ++ otg_dev->os_dep.mphi_base + 0x1f0; ++ dwc_otg_hcd->fiq_state->mphi_regs.swirq_clr = ++ otg_dev->os_dep.mphi_base + 0x1f4; ++ DWC_WARN("Fake MPHI regs_base at 0x%08x", ++ (int)dwc_otg_hcd->fiq_state->mphi_regs.base); ++ } else { ++ dwc_otg_hcd->fiq_state->mphi_regs.ctrl = ++ otg_dev->os_dep.mphi_base + 0x4c; ++ dwc_otg_hcd->fiq_state->mphi_regs.outdda ++ = otg_dev->os_dep.mphi_base + 0x28; ++ dwc_otg_hcd->fiq_state->mphi_regs.outddb ++ = otg_dev->os_dep.mphi_base + 0x2c; ++ dwc_otg_hcd->fiq_state->mphi_regs.intstat ++ = otg_dev->os_dep.mphi_base + 0x50; ++ DWC_WARN("MPHI regs_base at %px", ++ dwc_otg_hcd->fiq_state->mphi_regs.base); ++ ++ //Enable mphi peripheral ++ writel((1<<31),dwc_otg_hcd->fiq_state->mphi_regs.ctrl); ++#ifdef DEBUG ++ if (readl(dwc_otg_hcd->fiq_state->mphi_regs.ctrl) & 0x80000000) ++ DWC_WARN("MPHI periph has been enabled"); ++ else ++ DWC_WARN("MPHI periph has NOT been enabled"); ++#endif ++ } ++ // Enable FIQ interrupt from USB peripheral ++#ifdef CONFIG_ARM64 ++ irq = otg_dev->os_dep.fiq_num; ++ ++ if (irq < 0) { ++ DWC_ERROR("Can't get SIM-FIQ irq"); ++ return; ++ } ++ ++ retval = request_irq(irq, fiq_irq_handler, 0, "dwc_otg_sim-fiq", dwc_otg_hcd); ++ ++ if (retval < 0) { ++ DWC_ERROR("Unable to request SIM-FIQ irq\n"); ++ return; ++ } ++ ++ simfiq_irq = irq; ++#else ++#ifdef CONFIG_GENERIC_IRQ_MULTI_HANDLER ++ irq = otg_dev->os_dep.fiq_num; ++#else ++ irq = INTERRUPT_VC_USB; ++#endif ++ if (irq < 0) { ++ DWC_ERROR("Can't get FIQ irq"); ++ return; ++ } ++ /* ++ * We could take an interrupt immediately after enabling the FIQ. ++ * Ensure coherency of hcd->fiq_state. ++ */ ++ smp_mb(); ++ enable_fiq(irq); ++ local_fiq_enable(); ++#endif ++ ++} ++ ++/** ++ * Initializes the HCD. This function allocates memory for and initializes the ++ * static parts of the usb_hcd and dwc_otg_hcd structures. It also registers the ++ * USB bus with the core and calls the hc_driver->start() function. It returns ++ * a negative error on failure. ++ */ ++int hcd_init(dwc_bus_dev_t *_dev) ++{ ++ struct usb_hcd *hcd = NULL; ++ dwc_otg_hcd_t *dwc_otg_hcd = NULL; ++ dwc_otg_device_t *otg_dev = DWC_OTG_BUSDRVDATA(_dev); ++ int retval = 0; ++ u64 dmamask; ++ ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD INIT otg_dev=%p\n", otg_dev); ++ ++ /* Set device flags indicating whether the HCD supports DMA. */ ++ if (dwc_otg_is_dma_enable(otg_dev->core_if)) ++ dmamask = DMA_BIT_MASK(32); ++ else ++ dmamask = 0; ++ ++#if defined(LM_INTERFACE) || defined(PLATFORM_INTERFACE) ++ dma_set_mask(&_dev->dev, dmamask); ++ dma_set_coherent_mask(&_dev->dev, dmamask); ++#elif defined(PCI_INTERFACE) ++ pci_set_dma_mask(_dev, dmamask); ++ pci_set_consistent_dma_mask(_dev, dmamask); ++#endif ++ ++ /* ++ * Allocate memory for the base HCD plus the DWC OTG HCD. ++ * Initialize the base HCD. ++ */ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,30) ++ hcd = usb_create_hcd(&dwc_otg_hc_driver, &_dev->dev, _dev->dev.bus_id); ++#else ++ hcd = usb_create_hcd(&dwc_otg_hc_driver, &_dev->dev, dev_name(&_dev->dev)); ++ hcd->has_tt = 1; ++// hcd->uses_new_polling = 1; ++// hcd->poll_rh = 0; ++#endif ++ if (!hcd) { ++ retval = -ENOMEM; ++ goto error1; ++ } ++ ++ hcd->regs = otg_dev->os_dep.base; ++ ++ ++ /* Initialize the DWC OTG HCD. */ ++ dwc_otg_hcd = dwc_otg_hcd_alloc_hcd(); ++ if (!dwc_otg_hcd) { ++ goto error2; ++ } ++ ((struct wrapper_priv_data *)(hcd->hcd_priv))->dwc_otg_hcd = ++ dwc_otg_hcd; ++ otg_dev->hcd = dwc_otg_hcd; ++ otg_dev->hcd->otg_dev = otg_dev; ++ ++#ifdef CONFIG_ARM64 ++ if (dwc_otg_hcd_init(dwc_otg_hcd, otg_dev->core_if)) ++ goto error2; ++ ++ if (fiq_enable) ++ hcd_init_fiq(otg_dev); ++#else ++ if (dwc_otg_hcd_init(dwc_otg_hcd, otg_dev->core_if)) { ++ goto error2; ++ } ++ ++ if (fiq_enable) { ++ if (num_online_cpus() > 1) { ++ /* ++ * bcm2709: can run the FIQ on a separate core to IRQs. ++ * Ensure driver state is visible to other cores before setting up the FIQ. ++ */ ++ smp_mb(); ++ smp_call_function_single(1, hcd_init_fiq, otg_dev, 1); ++ } else { ++ smp_call_function_single(0, hcd_init_fiq, otg_dev, 1); ++ } ++ } ++#endif ++ ++ hcd->self.otg_port = dwc_otg_hcd_otg_port(dwc_otg_hcd); ++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,33) //don't support for LM(with 2.6.20.1 kernel) ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,35) //version field absent later ++ hcd->self.otg_version = dwc_otg_get_otg_version(otg_dev->core_if); ++#endif ++ /* Don't support SG list at this point */ ++ hcd->self.sg_tablesize = 0; ++#endif ++ /* ++ * Finish generic HCD initialization and start the HCD. This function ++ * allocates the DMA buffer pool, registers the USB bus, requests the ++ * IRQ line, and calls hcd_start method. ++ */ ++ retval = usb_add_hcd(hcd, otg_dev->os_dep.irq_num, IRQF_SHARED); ++ if (retval < 0) { ++ goto error2; ++ } ++ ++ dwc_otg_hcd_set_priv_data(dwc_otg_hcd, hcd); ++ return 0; ++ ++error2: ++ usb_put_hcd(hcd); ++error1: ++ return retval; ++} ++ ++/** ++ * Removes the HCD. ++ * Frees memory and resources associated with the HCD and deregisters the bus. ++ */ ++void hcd_remove(dwc_bus_dev_t *_dev) ++{ ++ dwc_otg_device_t *otg_dev = DWC_OTG_BUSDRVDATA(_dev); ++ dwc_otg_hcd_t *dwc_otg_hcd; ++ struct usb_hcd *hcd; ++ ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD REMOVE otg_dev=%p\n", otg_dev); ++ ++ if (!otg_dev) { ++ DWC_DEBUGPL(DBG_ANY, "%s: otg_dev NULL!\n", __func__); ++ return; ++ } ++ ++ dwc_otg_hcd = otg_dev->hcd; ++ ++ if (!dwc_otg_hcd) { ++ DWC_DEBUGPL(DBG_ANY, "%s: otg_dev->hcd NULL!\n", __func__); ++ return; ++ } ++ ++ hcd = dwc_otg_hcd_to_hcd(dwc_otg_hcd); ++ ++ if (!hcd) { ++ DWC_DEBUGPL(DBG_ANY, ++ "%s: dwc_otg_hcd_to_hcd(dwc_otg_hcd) NULL!\n", ++ __func__); ++ return; ++ } ++ usb_remove_hcd(hcd); ++ dwc_otg_hcd_set_priv_data(dwc_otg_hcd, NULL); ++ dwc_otg_hcd_remove(dwc_otg_hcd); ++ usb_put_hcd(hcd); ++} ++ ++/* ========================================================================= ++ * Linux HC Driver Functions ++ * ========================================================================= */ ++ ++/** Initializes the DWC_otg controller and its root hub and prepares it for host ++ * mode operation. Activates the root port. Returns 0 on success and a negative ++ * error code on failure. */ ++int hcd_start(struct usb_hcd *hcd) ++{ ++ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd); ++ struct usb_bus *bus; ++ ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD START\n"); ++ bus = hcd_to_bus(hcd); ++ ++ hcd->state = HC_STATE_RUNNING; ++ if (dwc_otg_hcd_start(dwc_otg_hcd, &hcd_fops)) { ++ return 0; ++ } ++ ++ /* Initialize and connect root hub if one is not already attached */ ++ if (bus->root_hub) { ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD Has Root Hub\n"); ++ /* Inform the HUB driver to resume. */ ++ usb_hcd_resume_root_hub(hcd); ++ } ++ ++ return 0; ++} ++ ++/** ++ * Halts the DWC_otg host mode operations in a clean manner. USB transfers are ++ * stopped. ++ */ ++void hcd_stop(struct usb_hcd *hcd) ++{ ++ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd); ++ ++ dwc_otg_hcd_stop(dwc_otg_hcd); ++} ++ ++/** Returns the current frame number. */ ++static int get_frame_number(struct usb_hcd *hcd) ++{ ++ hprt0_data_t hprt0; ++ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd); ++ hprt0.d32 = DWC_READ_REG32(dwc_otg_hcd->core_if->host_if->hprt0); ++ if (hprt0.b.prtspd == DWC_HPRT0_PRTSPD_HIGH_SPEED) ++ return dwc_otg_hcd_get_frame_number(dwc_otg_hcd) >> 3; ++ else ++ return dwc_otg_hcd_get_frame_number(dwc_otg_hcd); ++} ++ ++#ifdef DEBUG ++static void dump_urb_info(struct urb *urb, char *fn_name) ++{ ++ DWC_PRINTF("%s, urb %p\n", fn_name, urb); ++ DWC_PRINTF(" Device address: %d\n", usb_pipedevice(urb->pipe)); ++ DWC_PRINTF(" Endpoint: %d, %s\n", usb_pipeendpoint(urb->pipe), ++ (usb_pipein(urb->pipe) ? "IN" : "OUT")); ++ DWC_PRINTF(" Endpoint type: %s\n", ( { ++ char *pipetype; ++ switch (usb_pipetype(urb->pipe)) { ++case PIPE_CONTROL: ++pipetype = "CONTROL"; break; case PIPE_BULK: ++pipetype = "BULK"; break; case PIPE_INTERRUPT: ++pipetype = "INTERRUPT"; break; case PIPE_ISOCHRONOUS: ++pipetype = "ISOCHRONOUS"; break; default: ++ pipetype = "UNKNOWN"; break;}; ++ pipetype;} ++ )) ; ++ DWC_PRINTF(" Speed: %s\n", ( { ++ char *speed; switch (urb->dev->speed) { ++case USB_SPEED_HIGH: ++speed = "HIGH"; break; case USB_SPEED_FULL: ++speed = "FULL"; break; case USB_SPEED_LOW: ++speed = "LOW"; break; default: ++ speed = "UNKNOWN"; break;}; ++ speed;} ++ )) ; ++ DWC_PRINTF(" Max packet size: %d\n", ++ usb_maxpacket(urb->dev, urb->pipe, usb_pipeout(urb->pipe))); ++ DWC_PRINTF(" Data buffer length: %d\n", urb->transfer_buffer_length); ++ DWC_PRINTF(" Transfer buffer: %p, Transfer DMA: %p\n", ++ urb->transfer_buffer, (void *)urb->transfer_dma); ++ DWC_PRINTF(" Setup buffer: %p, Setup DMA: %p\n", ++ urb->setup_packet, (void *)urb->setup_dma); ++ DWC_PRINTF(" Interval: %d\n", urb->interval); ++ if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { ++ int i; ++ for (i = 0; i < urb->number_of_packets; i++) { ++ DWC_PRINTF(" ISO Desc %d:\n", i); ++ DWC_PRINTF(" offset: %d, length %d\n", ++ urb->iso_frame_desc[i].offset, ++ urb->iso_frame_desc[i].length); ++ } ++ } ++} ++#endif ++ ++/** Starts processing a USB transfer request specified by a USB Request Block ++ * (URB). mem_flags indicates the type of memory allocation to use while ++ * processing this URB. */ ++static int dwc_otg_urb_enqueue(struct usb_hcd *hcd, ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28) ++ struct usb_host_endpoint *ep, ++#endif ++ struct urb *urb, gfp_t mem_flags) ++{ ++ int retval = 0; ++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,28) ++ struct usb_host_endpoint *ep = urb->ep; ++#endif ++ dwc_irqflags_t irqflags; ++ void **ref_ep_hcpriv = &ep->hcpriv; ++ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd); ++ dwc_otg_hcd_urb_t *dwc_otg_urb; ++ int i; ++ int alloc_bandwidth = 0; ++ uint8_t ep_type = 0; ++ uint32_t flags = 0; ++ void *buf; ++ ++#ifdef DEBUG ++ if (CHK_DEBUG_LEVEL(DBG_HCDV | DBG_HCD_URB)) { ++ dump_urb_info(urb, "dwc_otg_urb_enqueue"); ++ } ++#endif ++ if ((usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) ++ || (usb_pipetype(urb->pipe) == PIPE_INTERRUPT)) { ++ if (!dwc_otg_hcd_is_bandwidth_allocated ++ (dwc_otg_hcd, ref_ep_hcpriv)) { ++ alloc_bandwidth = 1; ++ } ++ } ++ ++ switch (usb_pipetype(urb->pipe)) { ++ case PIPE_CONTROL: ++ ep_type = USB_ENDPOINT_XFER_CONTROL; ++ break; ++ case PIPE_ISOCHRONOUS: ++ ep_type = USB_ENDPOINT_XFER_ISOC; ++ break; ++ case PIPE_BULK: ++ ep_type = USB_ENDPOINT_XFER_BULK; ++ break; ++ case PIPE_INTERRUPT: ++ ep_type = USB_ENDPOINT_XFER_INT; ++ break; ++ default: ++ DWC_WARN("Wrong EP type - %d\n", usb_pipetype(urb->pipe)); ++ } ++ ++ /* # of packets is often 0 - do we really need to call this then? */ ++ dwc_otg_urb = dwc_otg_hcd_urb_alloc(dwc_otg_hcd, ++ urb->number_of_packets, ++ mem_flags == GFP_ATOMIC ? 1 : 0); ++ ++ if(dwc_otg_urb == NULL) ++ return -ENOMEM; ++ ++ if (!dwc_otg_urb && urb->number_of_packets) ++ return -ENOMEM; ++ ++ dwc_otg_hcd_urb_set_pipeinfo(dwc_otg_urb, usb_pipedevice(urb->pipe), ++ usb_pipeendpoint(urb->pipe), ep_type, ++ usb_pipein(urb->pipe), ++ usb_maxpacket(urb->dev, urb->pipe, ++ !(usb_pipein(urb->pipe)))); ++ ++ buf = urb->transfer_buffer; ++ if (hcd_uses_dma(hcd) && !buf && urb->transfer_buffer_length) { ++ /* ++ * Calculate virtual address from physical address, ++ * because some class driver may not fill transfer_buffer. ++ * In Buffer DMA mode virual address is used, ++ * when handling non DWORD aligned buffers. ++ */ ++ buf = (void *)__bus_to_virt((unsigned long)urb->transfer_dma); ++ dev_warn_once(&urb->dev->dev, ++ "USB transfer_buffer was NULL, will use __bus_to_virt(%pad)=%p\n", ++ &urb->transfer_dma, buf); ++ } ++ ++ if (!buf && urb->transfer_buffer_length) { ++ DWC_FREE(dwc_otg_urb); ++ DWC_ERROR("transfer_buffer is NULL in PIO mode or both " ++ "transfer_buffer and transfer_dma are NULL in DMA mode\n"); ++ return -EINVAL; ++ } ++ ++ if (!(urb->transfer_flags & URB_NO_INTERRUPT)) ++ flags |= URB_GIVEBACK_ASAP; ++ if (urb->transfer_flags & URB_ZERO_PACKET) ++ flags |= URB_SEND_ZERO_PACKET; ++ ++ dwc_otg_hcd_urb_set_params(dwc_otg_urb, urb, buf, ++ urb->transfer_dma, ++ urb->transfer_buffer_length, ++ urb->setup_packet, ++ urb->setup_dma, flags, urb->interval); ++ ++ for (i = 0; i < urb->number_of_packets; ++i) { ++ dwc_otg_hcd_urb_set_iso_desc_params(dwc_otg_urb, i, ++ urb-> ++ iso_frame_desc[i].offset, ++ urb-> ++ iso_frame_desc[i].length); ++ } ++ ++ DWC_SPINLOCK_IRQSAVE(dwc_otg_hcd->lock, &irqflags); ++ urb->hcpriv = dwc_otg_urb; ++#if USB_URB_EP_LINKING ++ retval = usb_hcd_link_urb_to_ep(hcd, urb); ++ if (0 == retval) ++#endif ++ { ++ retval = dwc_otg_hcd_urb_enqueue(dwc_otg_hcd, dwc_otg_urb, ++ /*(dwc_otg_qh_t **)*/ ++ ref_ep_hcpriv, 1); ++ if (0 == retval) { ++ if (alloc_bandwidth) { ++ allocate_bus_bandwidth(hcd, ++ dwc_otg_hcd_get_ep_bandwidth( ++ dwc_otg_hcd, *ref_ep_hcpriv), ++ urb); ++ } ++ } else { ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG dwc_otg_hcd_urb_enqueue failed rc %d\n", retval); ++#if USB_URB_EP_LINKING ++ usb_hcd_unlink_urb_from_ep(hcd, urb); ++#endif ++ DWC_FREE(dwc_otg_urb); ++ urb->hcpriv = NULL; ++ if (retval == -DWC_E_NO_DEVICE) ++ retval = -ENODEV; ++ } ++ } ++#if USB_URB_EP_LINKING ++ else ++ { ++ DWC_FREE(dwc_otg_urb); ++ urb->hcpriv = NULL; ++ } ++#endif ++ DWC_SPINUNLOCK_IRQRESTORE(dwc_otg_hcd->lock, irqflags); ++ return retval; ++} ++ ++/** Aborts/cancels a USB transfer request. Always returns 0 to indicate ++ * success. */ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28) ++static int dwc_otg_urb_dequeue(struct usb_hcd *hcd, struct urb *urb) ++#else ++static int dwc_otg_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status) ++#endif ++{ ++ dwc_irqflags_t flags; ++ dwc_otg_hcd_t *dwc_otg_hcd; ++ int rc; ++ ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD URB Dequeue\n"); ++ ++ dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd); ++ ++#ifdef DEBUG ++ if (CHK_DEBUG_LEVEL(DBG_HCDV | DBG_HCD_URB)) { ++ dump_urb_info(urb, "dwc_otg_urb_dequeue"); ++ } ++#endif ++ ++ DWC_SPINLOCK_IRQSAVE(dwc_otg_hcd->lock, &flags); ++ rc = usb_hcd_check_unlink_urb(hcd, urb, status); ++ if (0 == rc) { ++ if(urb->hcpriv != NULL) { ++ dwc_otg_hcd_urb_dequeue(dwc_otg_hcd, ++ (dwc_otg_hcd_urb_t *)urb->hcpriv); ++ ++ DWC_FREE(urb->hcpriv); ++ urb->hcpriv = NULL; ++ } ++ } ++ ++ if (0 == rc) { ++ /* Higher layer software sets URB status. */ ++#if USB_URB_EP_LINKING ++ usb_hcd_unlink_urb_from_ep(hcd, urb); ++#endif ++ DWC_SPINUNLOCK_IRQRESTORE(dwc_otg_hcd->lock, flags); ++ ++ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28) ++ usb_hcd_giveback_urb(hcd, urb); ++#else ++ usb_hcd_giveback_urb(hcd, urb, status); ++#endif ++ if (CHK_DEBUG_LEVEL(DBG_HCDV | DBG_HCD_URB)) { ++ DWC_PRINTF("Called usb_hcd_giveback_urb() \n"); ++ DWC_PRINTF(" 1urb->status = %d\n", urb->status); ++ } ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD URB Dequeue OK\n"); ++ } else { ++ DWC_SPINUNLOCK_IRQRESTORE(dwc_otg_hcd->lock, flags); ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD URB Dequeue failed - rc %d\n", ++ rc); ++ } ++ ++ return rc; ++} ++ ++/* Frees resources in the DWC_otg controller related to a given endpoint. Also ++ * clears state in the HCD related to the endpoint. Any URBs for the endpoint ++ * must already be dequeued. */ ++static void endpoint_disable(struct usb_hcd *hcd, struct usb_host_endpoint *ep) ++{ ++ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd); ++ ++ DWC_DEBUGPL(DBG_HCD, ++ "DWC OTG HCD EP DISABLE: _bEndpointAddress=0x%02x, " ++ "endpoint=%d\n", ep->desc.bEndpointAddress, ++ dwc_ep_addr_to_endpoint(ep->desc.bEndpointAddress)); ++ dwc_otg_hcd_endpoint_disable(dwc_otg_hcd, ep->hcpriv, 250); ++ ep->hcpriv = NULL; ++} ++ ++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,30) ++/* Resets endpoint specific parameter values, in current version used to reset ++ * the data toggle(as a WA). This function can be called from usb_clear_halt routine */ ++static void endpoint_reset(struct usb_hcd *hcd, struct usb_host_endpoint *ep) ++{ ++ dwc_irqflags_t flags; ++ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd); ++ ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD EP RESET: Endpoint Num=0x%02d\n", epnum); ++ ++ DWC_SPINLOCK_IRQSAVE(dwc_otg_hcd->lock, &flags); ++ if (ep->hcpriv) { ++ dwc_otg_hcd_endpoint_reset(dwc_otg_hcd, ep->hcpriv); ++ } ++ DWC_SPINUNLOCK_IRQRESTORE(dwc_otg_hcd->lock, flags); ++} ++#endif ++ ++/** Handles host mode interrupts for the DWC_otg controller. Returns IRQ_NONE if ++ * there was no interrupt to handle. Returns IRQ_HANDLED if there was a valid ++ * interrupt. ++ * ++ * This function is called by the USB core when an interrupt occurs */ ++static irqreturn_t dwc_otg_hcd_irq(struct usb_hcd *hcd) ++{ ++ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd); ++ int32_t retval = dwc_otg_hcd_handle_intr(dwc_otg_hcd); ++ if (retval != 0) { ++ S3C2410X_CLEAR_EINTPEND(); ++ } ++ return IRQ_RETVAL(retval); ++} ++ ++/** Creates Status Change bitmap for the root hub and root port. The bitmap is ++ * returned in buf. Bit 0 is the status change indicator for the root hub. Bit 1 ++ * is the status change indicator for the single root port. Returns 1 if either ++ * change indicator is 1, otherwise returns 0. */ ++int hub_status_data(struct usb_hcd *hcd, char *buf) ++{ ++ dwc_otg_hcd_t *dwc_otg_hcd = hcd_to_dwc_otg_hcd(hcd); ++ ++ buf[0] = 0; ++ buf[0] |= (dwc_otg_hcd_is_status_changed(dwc_otg_hcd, 1)) << 1; ++ ++ return (buf[0] != 0); ++} ++ ++/** Handles hub class-specific requests. */ ++int hub_control(struct usb_hcd *hcd, ++ u16 typeReq, u16 wValue, u16 wIndex, char *buf, u16 wLength) ++{ ++ int retval; ++ ++ retval = dwc_otg_hcd_hub_control(hcd_to_dwc_otg_hcd(hcd), ++ typeReq, wValue, wIndex, buf, wLength); ++ ++ switch (retval) { ++ case -DWC_E_INVALID: ++ retval = -EINVAL; ++ break; ++ } ++ ++ return retval; ++} ++ ++#endif /* DWC_DEVICE_ONLY */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_hcd_queue.c +@@ -0,0 +1,970 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_hcd_queue.c $ ++ * $Revision: #44 $ ++ * $Date: 2011/10/26 $ ++ * $Change: 1873028 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++#ifndef DWC_DEVICE_ONLY ++ ++/** ++ * @file ++ * ++ * This file contains the functions to manage Queue Heads and Queue ++ * Transfer Descriptors. ++ */ ++ ++#include "dwc_otg_hcd.h" ++#include "dwc_otg_regs.h" ++ ++extern bool microframe_schedule; ++extern unsigned short int_ep_interval_min; ++ ++/** ++ * Free each QTD in the QH's QTD-list then free the QH. QH should already be ++ * removed from a list. QTD list should already be empty if called from URB ++ * Dequeue. ++ * ++ * @param hcd HCD instance. ++ * @param qh The QH to free. ++ */ ++void dwc_otg_hcd_qh_free(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ dwc_otg_qtd_t *qtd, *qtd_tmp; ++ dwc_irqflags_t flags; ++ uint32_t buf_size = 0; ++ uint8_t *align_buf_virt = NULL; ++ dwc_dma_t align_buf_dma; ++ struct device *dev = dwc_otg_hcd_to_dev(hcd); ++ ++ /* Free each QTD in the QTD list */ ++ DWC_SPINLOCK_IRQSAVE(hcd->lock, &flags); ++ DWC_CIRCLEQ_FOREACH_SAFE(qtd, qtd_tmp, &qh->qtd_list, qtd_list_entry) { ++ DWC_CIRCLEQ_REMOVE(&qh->qtd_list, qtd, qtd_list_entry); ++ dwc_otg_hcd_qtd_free(qtd); ++ } ++ ++ if (hcd->core_if->dma_desc_enable) { ++ dwc_otg_hcd_qh_free_ddma(hcd, qh); ++ } else if (qh->dw_align_buf) { ++ if (qh->ep_type == UE_ISOCHRONOUS) { ++ buf_size = 4096; ++ } else { ++ buf_size = hcd->core_if->core_params->max_transfer_size; ++ } ++ align_buf_virt = qh->dw_align_buf; ++ align_buf_dma = qh->dw_align_buf_dma; ++ } ++ ++ DWC_FREE(qh); ++ DWC_SPINUNLOCK_IRQRESTORE(hcd->lock, flags); ++ if (align_buf_virt) ++ DWC_DMA_FREE(dev, buf_size, align_buf_virt, align_buf_dma); ++ return; ++} ++ ++#define BitStuffTime(bytecount) ((8 * 7* bytecount) / 6) ++#define HS_HOST_DELAY 5 /* nanoseconds */ ++#define FS_LS_HOST_DELAY 1000 /* nanoseconds */ ++#define HUB_LS_SETUP 333 /* nanoseconds */ ++#define NS_TO_US(ns) ((ns + 500) / 1000) ++ /* convert & round nanoseconds to microseconds */ ++ ++static uint32_t calc_bus_time(int speed, int is_in, int is_isoc, int bytecount) ++{ ++ unsigned long retval; ++ ++ switch (speed) { ++ case USB_SPEED_HIGH: ++ if (is_isoc) { ++ retval = ++ ((38 * 8 * 2083) + ++ (2083 * (3 + BitStuffTime(bytecount)))) / 1000 + ++ HS_HOST_DELAY; ++ } else { ++ retval = ++ ((55 * 8 * 2083) + ++ (2083 * (3 + BitStuffTime(bytecount)))) / 1000 + ++ HS_HOST_DELAY; ++ } ++ break; ++ case USB_SPEED_FULL: ++ if (is_isoc) { ++ retval = ++ (8354 * (31 + 10 * BitStuffTime(bytecount))) / 1000; ++ if (is_in) { ++ retval = 7268 + FS_LS_HOST_DELAY + retval; ++ } else { ++ retval = 6265 + FS_LS_HOST_DELAY + retval; ++ } ++ } else { ++ retval = ++ (8354 * (31 + 10 * BitStuffTime(bytecount))) / 1000; ++ retval = 9107 + FS_LS_HOST_DELAY + retval; ++ } ++ break; ++ case USB_SPEED_LOW: ++ if (is_in) { ++ retval = ++ (67667 * (31 + 10 * BitStuffTime(bytecount))) / ++ 1000; ++ retval = ++ 64060 + (2 * HUB_LS_SETUP) + FS_LS_HOST_DELAY + ++ retval; ++ } else { ++ retval = ++ (66700 * (31 + 10 * BitStuffTime(bytecount))) / ++ 1000; ++ retval = ++ 64107 + (2 * HUB_LS_SETUP) + FS_LS_HOST_DELAY + ++ retval; ++ } ++ break; ++ default: ++ DWC_WARN("Unknown device speed\n"); ++ retval = -1; ++ } ++ ++ return NS_TO_US(retval); ++} ++ ++/** ++ * Initializes a QH structure. ++ * ++ * @param hcd The HCD state structure for the DWC OTG controller. ++ * @param qh The QH to init. ++ * @param urb Holds the information about the device/endpoint that we need ++ * to initialize the QH. ++ */ ++#define SCHEDULE_SLOP 10 ++void qh_init(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh, dwc_otg_hcd_urb_t * urb) ++{ ++ char *speed, *type; ++ int dev_speed; ++ uint32_t hub_addr, hub_port; ++ hprt0_data_t hprt; ++ ++ dwc_memset(qh, 0, sizeof(dwc_otg_qh_t)); ++ hprt.d32 = DWC_READ_REG32(hcd->core_if->host_if->hprt0); ++ ++ /* Initialize QH */ ++ qh->ep_type = dwc_otg_hcd_get_pipe_type(&urb->pipe_info); ++ qh->ep_is_in = dwc_otg_hcd_is_pipe_in(&urb->pipe_info) ? 1 : 0; ++ ++ qh->data_toggle = DWC_OTG_HC_PID_DATA0; ++ qh->maxp = dwc_otg_hcd_get_mps(&urb->pipe_info); ++ DWC_CIRCLEQ_INIT(&qh->qtd_list); ++ DWC_LIST_INIT(&qh->qh_list_entry); ++ qh->channel = NULL; ++ ++ /* FS/LS Enpoint on HS Hub ++ * NOT virtual root hub */ ++ dev_speed = hcd->fops->speed(hcd, urb->priv); ++ ++ hcd->fops->hub_info(hcd, urb->priv, &hub_addr, &hub_port); ++ qh->do_split = 0; ++ if (microframe_schedule) ++ qh->speed = dev_speed; ++ ++ qh->nak_frame = 0xffff; ++ ++ if (hprt.b.prtspd == DWC_HPRT0_PRTSPD_HIGH_SPEED && ++ dev_speed != USB_SPEED_HIGH) { ++ DWC_DEBUGPL(DBG_HCD, ++ "QH init: EP %d: TT found at hub addr %d, for port %d\n", ++ dwc_otg_hcd_get_ep_num(&urb->pipe_info), hub_addr, ++ hub_port); ++ qh->do_split = 1; ++ qh->skip_count = 0; ++ } ++ ++ if (qh->ep_type == UE_INTERRUPT || qh->ep_type == UE_ISOCHRONOUS) { ++ /* Compute scheduling parameters once and save them. */ ++ ++ /** @todo Account for split transfers in the bus time. */ ++ int bytecount = ++ dwc_hb_mult(qh->maxp) * dwc_max_packet(qh->maxp); ++ ++ qh->usecs = ++ calc_bus_time((qh->do_split ? USB_SPEED_HIGH : dev_speed), ++ qh->ep_is_in, (qh->ep_type == UE_ISOCHRONOUS), ++ bytecount); ++ /* Start in a slightly future (micro)frame. */ ++ qh->sched_frame = dwc_frame_num_inc(hcd->frame_number, ++ SCHEDULE_SLOP); ++ qh->interval = urb->interval; ++ ++ if (hprt.b.prtspd == DWC_HPRT0_PRTSPD_HIGH_SPEED) { ++ if (dev_speed == USB_SPEED_LOW || ++ dev_speed == USB_SPEED_FULL) { ++ qh->interval *= 8; ++ qh->sched_frame |= 0x7; ++ qh->start_split_frame = qh->sched_frame; ++ } else if (int_ep_interval_min >= 2 && ++ qh->interval < int_ep_interval_min && ++ qh->ep_type == UE_INTERRUPT) { ++ qh->interval = int_ep_interval_min; ++ } ++ } ++ } ++ ++ DWC_DEBUGPL(DBG_HCD, "DWC OTG HCD QH Initialized\n"); ++ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - qh = %p\n", qh); ++ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - Device Address = %d\n", ++ dwc_otg_hcd_get_dev_addr(&urb->pipe_info)); ++ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - Endpoint %d, %s\n", ++ dwc_otg_hcd_get_ep_num(&urb->pipe_info), ++ dwc_otg_hcd_is_pipe_in(&urb->pipe_info) ? "IN" : "OUT"); ++ switch (dev_speed) { ++ case USB_SPEED_LOW: ++ qh->dev_speed = DWC_OTG_EP_SPEED_LOW; ++ speed = "low"; ++ break; ++ case USB_SPEED_FULL: ++ qh->dev_speed = DWC_OTG_EP_SPEED_FULL; ++ speed = "full"; ++ break; ++ case USB_SPEED_HIGH: ++ qh->dev_speed = DWC_OTG_EP_SPEED_HIGH; ++ speed = "high"; ++ break; ++ default: ++ speed = "?"; ++ break; ++ } ++ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - Speed = %s\n", speed); ++ ++ switch (qh->ep_type) { ++ case UE_ISOCHRONOUS: ++ type = "isochronous"; ++ break; ++ case UE_INTERRUPT: ++ type = "interrupt"; ++ break; ++ case UE_CONTROL: ++ type = "control"; ++ break; ++ case UE_BULK: ++ type = "bulk"; ++ break; ++ default: ++ type = "?"; ++ break; ++ } ++ ++ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - Type = %s\n", type); ++ ++#ifdef DEBUG ++ if (qh->ep_type == UE_INTERRUPT) { ++ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - usecs = %d\n", ++ qh->usecs); ++ DWC_DEBUGPL(DBG_HCDV, "DWC OTG HCD QH - interval = %d\n", ++ qh->interval); ++ } ++#endif ++ ++} ++ ++/** ++ * This function allocates and initializes a QH. ++ * ++ * @param hcd The HCD state structure for the DWC OTG controller. ++ * @param urb Holds the information about the device/endpoint that we need ++ * to initialize the QH. ++ * @param atomic_alloc Flag to do atomic allocation if needed ++ * ++ * @return Returns pointer to the newly allocated QH, or NULL on error. */ ++dwc_otg_qh_t *dwc_otg_hcd_qh_create(dwc_otg_hcd_t * hcd, ++ dwc_otg_hcd_urb_t * urb, int atomic_alloc) ++{ ++ dwc_otg_qh_t *qh; ++ ++ /* Allocate memory */ ++ /** @todo add memflags argument */ ++ qh = dwc_otg_hcd_qh_alloc(atomic_alloc); ++ if (qh == NULL) { ++ DWC_ERROR("qh allocation failed"); ++ return NULL; ++ } ++ ++ qh_init(hcd, qh, urb); ++ ++ if (hcd->core_if->dma_desc_enable ++ && (dwc_otg_hcd_qh_init_ddma(hcd, qh) < 0)) { ++ dwc_otg_hcd_qh_free(hcd, qh); ++ return NULL; ++ } ++ ++ return qh; ++} ++ ++/* microframe_schedule=0 start */ ++ ++/** ++ * Checks that a channel is available for a periodic transfer. ++ * ++ * @return 0 if successful, negative error code otherise. ++ */ ++static int periodic_channel_available(dwc_otg_hcd_t * hcd) ++{ ++ /* ++ * Currently assuming that there is a dedicated host channnel for each ++ * periodic transaction plus at least one host channel for ++ * non-periodic transactions. ++ */ ++ int status; ++ int num_channels; ++ ++ num_channels = hcd->core_if->core_params->host_channels; ++ if ((hcd->periodic_channels + hcd->non_periodic_channels < num_channels) ++ && (hcd->periodic_channels < num_channels - 1)) { ++ status = 0; ++ } else { ++ DWC_INFO("%s: Total channels: %d, Periodic: %d, Non-periodic: %d\n", ++ __func__, num_channels, hcd->periodic_channels, hcd->non_periodic_channels); //NOTICE ++ status = -DWC_E_NO_SPACE; ++ } ++ ++ return status; ++} ++ ++/** ++ * Checks that there is sufficient bandwidth for the specified QH in the ++ * periodic schedule. For simplicity, this calculation assumes that all the ++ * transfers in the periodic schedule may occur in the same (micro)frame. ++ * ++ * @param hcd The HCD state structure for the DWC OTG controller. ++ * @param qh QH containing periodic bandwidth required. ++ * ++ * @return 0 if successful, negative error code otherwise. ++ */ ++static int check_periodic_bandwidth(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ int status; ++ int16_t max_claimed_usecs; ++ ++ status = 0; ++ ++ if ((qh->dev_speed == DWC_OTG_EP_SPEED_HIGH) || qh->do_split) { ++ /* ++ * High speed mode. ++ * Max periodic usecs is 80% x 125 usec = 100 usec. ++ */ ++ ++ max_claimed_usecs = 100 - qh->usecs; ++ } else { ++ /* ++ * Full speed mode. ++ * Max periodic usecs is 90% x 1000 usec = 900 usec. ++ */ ++ max_claimed_usecs = 900 - qh->usecs; ++ } ++ ++ if (hcd->periodic_usecs > max_claimed_usecs) { ++ DWC_INFO("%s: already claimed usecs %d, required usecs %d\n", __func__, hcd->periodic_usecs, qh->usecs); //NOTICE ++ status = -DWC_E_NO_SPACE; ++ } ++ ++ return status; ++} ++ ++/* microframe_schedule=0 end */ ++ ++/** ++ * Microframe scheduler ++ * track the total use in hcd->frame_usecs ++ * keep each qh use in qh->frame_usecs ++ * when surrendering the qh then donate the time back ++ */ ++const unsigned short max_uframe_usecs[]={ 100, 100, 100, 100, 100, 100, 30, 0 }; ++ ++/* ++ * called from dwc_otg_hcd.c:dwc_otg_hcd_init ++ */ ++void init_hcd_usecs(dwc_otg_hcd_t *_hcd) ++{ ++ int i; ++ if (_hcd->flags.b.port_speed == DWC_HPRT0_PRTSPD_FULL_SPEED) { ++ _hcd->frame_usecs[0] = 900; ++ for (i = 1; i < 8; i++) ++ _hcd->frame_usecs[i] = 0; ++ } else { ++ for (i = 0; i < 8; i++) ++ _hcd->frame_usecs[i] = max_uframe_usecs[i]; ++ } ++} ++ ++static int find_single_uframe(dwc_otg_hcd_t * _hcd, dwc_otg_qh_t * _qh) ++{ ++ int i; ++ unsigned short utime; ++ int t_left; ++ int ret; ++ int done; ++ ++ ret = -1; ++ utime = _qh->usecs; ++ t_left = utime; ++ i = 0; ++ done = 0; ++ while (done == 0) { ++ /* At the start _hcd->frame_usecs[i] = max_uframe_usecs[i]; */ ++ if (utime <= _hcd->frame_usecs[i]) { ++ _hcd->frame_usecs[i] -= utime; ++ _qh->frame_usecs[i] += utime; ++ t_left -= utime; ++ ret = i; ++ done = 1; ++ return ret; ++ } else { ++ i++; ++ if (i == 8) { ++ done = 1; ++ ret = -1; ++ } ++ } ++ } ++ return ret; ++ } ++ ++/* ++ * use this for FS apps that can span multiple uframes ++ */ ++static int find_multi_uframe(dwc_otg_hcd_t * _hcd, dwc_otg_qh_t * _qh) ++{ ++ int i; ++ int j; ++ unsigned short utime; ++ int t_left; ++ int ret; ++ int done; ++ unsigned short xtime; ++ ++ ret = -1; ++ utime = _qh->usecs; ++ t_left = utime; ++ i = 0; ++ done = 0; ++loop: ++ while (done == 0) { ++ if(_hcd->frame_usecs[i] <= 0) { ++ i++; ++ if (i == 8) { ++ done = 1; ++ ret = -1; ++ } ++ goto loop; ++ } ++ ++ /* ++ * we need n consecutive slots ++ * so use j as a start slot j plus j+1 must be enough time (for now) ++ */ ++ xtime= _hcd->frame_usecs[i]; ++ for (j = i+1 ; j < 8 ; j++ ) { ++ /* ++ * if we add this frame remaining time to xtime we may ++ * be OK, if not we need to test j for a complete frame ++ */ ++ if ((xtime+_hcd->frame_usecs[j]) < utime) { ++ if (_hcd->frame_usecs[j] < max_uframe_usecs[j]) { ++ j = 8; ++ ret = -1; ++ continue; ++ } ++ } ++ if (xtime >= utime) { ++ ret = i; ++ j = 8; /* stop loop with a good value ret */ ++ continue; ++ } ++ /* add the frame time to x time */ ++ xtime += _hcd->frame_usecs[j]; ++ /* we must have a fully available next frame or break */ ++ if ((xtime < utime) ++ && (_hcd->frame_usecs[j] == max_uframe_usecs[j])) { ++ ret = -1; ++ j = 8; /* stop loop with a bad value ret */ ++ continue; ++ } ++ } ++ if (ret >= 0) { ++ t_left = utime; ++ for (j = i; (t_left>0) && (j < 8); j++ ) { ++ t_left -= _hcd->frame_usecs[j]; ++ if ( t_left <= 0 ) { ++ _qh->frame_usecs[j] += _hcd->frame_usecs[j] + t_left; ++ _hcd->frame_usecs[j]= -t_left; ++ ret = i; ++ done = 1; ++ } else { ++ _qh->frame_usecs[j] += _hcd->frame_usecs[j]; ++ _hcd->frame_usecs[j] = 0; ++ } ++ } ++ } else { ++ i++; ++ if (i == 8) { ++ done = 1; ++ ret = -1; ++ } ++ } ++ } ++ return ret; ++} ++ ++static int find_uframe(dwc_otg_hcd_t * _hcd, dwc_otg_qh_t * _qh) ++{ ++ int ret; ++ ret = -1; ++ ++ if (_qh->speed == USB_SPEED_HIGH || ++ _hcd->flags.b.port_speed == DWC_HPRT0_PRTSPD_FULL_SPEED) { ++ /* if this is a hs transaction we need a full frame - or account for FS usecs */ ++ ret = find_single_uframe(_hcd, _qh); ++ } else { ++ /* if this is a fs transaction we may need a sequence of frames */ ++ ret = find_multi_uframe(_hcd, _qh); ++ } ++ return ret; ++} ++ ++/** ++ * Checks that the max transfer size allowed in a host channel is large enough ++ * to handle the maximum data transfer in a single (micro)frame for a periodic ++ * transfer. ++ * ++ * @param hcd The HCD state structure for the DWC OTG controller. ++ * @param qh QH for a periodic endpoint. ++ * ++ * @return 0 if successful, negative error code otherwise. ++ */ ++static int check_max_xfer_size(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ int status; ++ uint32_t max_xfer_size; ++ uint32_t max_channel_xfer_size; ++ ++ status = 0; ++ ++ max_xfer_size = dwc_max_packet(qh->maxp) * dwc_hb_mult(qh->maxp); ++ max_channel_xfer_size = hcd->core_if->core_params->max_transfer_size; ++ ++ if (max_xfer_size > max_channel_xfer_size) { ++ DWC_INFO("%s: Periodic xfer length %d > " "max xfer length for channel %d\n", ++ __func__, max_xfer_size, max_channel_xfer_size); //NOTICE ++ status = -DWC_E_NO_SPACE; ++ } ++ ++ return status; ++} ++ ++ ++ ++/** ++ * Schedules an interrupt or isochronous transfer in the periodic schedule. ++ * ++ * @param hcd The HCD state structure for the DWC OTG controller. ++ * @param qh QH for the periodic transfer. The QH should already contain the ++ * scheduling information. ++ * ++ * @return 0 if successful, negative error code otherwise. ++ */ ++static int schedule_periodic(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ int status = 0; ++ ++ if (microframe_schedule) { ++ int frame; ++ status = find_uframe(hcd, qh); ++ frame = -1; ++ if (status == 0) { ++ frame = 7; ++ } else { ++ if (status > 0 ) ++ frame = status-1; ++ } ++ ++ /* Set the new frame up */ ++ if (frame > -1) { ++ qh->sched_frame &= ~0x7; ++ qh->sched_frame |= (frame & 7); ++ } ++ ++ if (status != -1) ++ status = 0; ++ } else { ++ status = periodic_channel_available(hcd); ++ if (status) { ++ DWC_INFO("%s: No host channel available for periodic " "transfer.\n", __func__); //NOTICE ++ return status; ++ } ++ ++ status = check_periodic_bandwidth(hcd, qh); ++ } ++ if (status) { ++ DWC_INFO("%s: Insufficient periodic bandwidth for " ++ "periodic transfer.\n", __func__); ++ return -DWC_E_NO_SPACE; ++ } ++ status = check_max_xfer_size(hcd, qh); ++ if (status) { ++ DWC_INFO("%s: Channel max transfer size too small " ++ "for periodic transfer.\n", __func__); ++ return status; ++ } ++ ++ if (hcd->core_if->dma_desc_enable) { ++ /* Don't rely on SOF and start in ready schedule */ ++ DWC_LIST_INSERT_TAIL(&hcd->periodic_sched_ready, &qh->qh_list_entry); ++ } ++ else { ++ if(fiq_enable && (DWC_LIST_EMPTY(&hcd->periodic_sched_inactive) || dwc_frame_num_le(qh->sched_frame, hcd->fiq_state->next_sched_frame))) ++ { ++ hcd->fiq_state->next_sched_frame = qh->sched_frame; ++ ++ } ++ /* Always start in the inactive schedule. */ ++ DWC_LIST_INSERT_TAIL(&hcd->periodic_sched_inactive, &qh->qh_list_entry); ++ } ++ ++ if (!microframe_schedule) { ++ /* Reserve the periodic channel. */ ++ hcd->periodic_channels++; ++ } ++ ++ /* Update claimed usecs per (micro)frame. */ ++ hcd->periodic_usecs += qh->usecs; ++ ++ return status; ++} ++ ++ ++/** ++ * This function adds a QH to either the non periodic or periodic schedule if ++ * it is not already in the schedule. If the QH is already in the schedule, no ++ * action is taken. ++ * ++ * @return 0 if successful, negative error code otherwise. ++ */ ++int dwc_otg_hcd_qh_add(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ int status = 0; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ if (!DWC_LIST_EMPTY(&qh->qh_list_entry)) { ++ /* QH already in a schedule. */ ++ return status; ++ } ++ ++ /* Add the new QH to the appropriate schedule */ ++ if (dwc_qh_is_non_per(qh)) { ++ /* Always start in the inactive schedule. */ ++ DWC_LIST_INSERT_TAIL(&hcd->non_periodic_sched_inactive, ++ &qh->qh_list_entry); ++ //hcd->fiq_state->kick_np_queues = 1; ++ } else { ++ status = schedule_periodic(hcd, qh); ++ if ( !hcd->periodic_qh_count ) { ++ intr_mask.b.sofintr = 1; ++ if (fiq_enable) { ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&hcd->fiq_state->lock); ++ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, intr_mask.d32, intr_mask.d32); ++ fiq_fsm_spin_unlock(&hcd->fiq_state->lock); ++ local_fiq_enable(); ++ } else { ++ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, intr_mask.d32, intr_mask.d32); ++ } ++ } ++ hcd->periodic_qh_count++; ++ } ++ ++ return status; ++} ++ ++/** ++ * Removes an interrupt or isochronous transfer from the periodic schedule. ++ * ++ * @param hcd The HCD state structure for the DWC OTG controller. ++ * @param qh QH for the periodic transfer. ++ */ ++static void deschedule_periodic(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ int i; ++ DWC_LIST_REMOVE_INIT(&qh->qh_list_entry); ++ ++ /* Update claimed usecs per (micro)frame. */ ++ hcd->periodic_usecs -= qh->usecs; ++ ++ if (!microframe_schedule) { ++ /* Release the periodic channel reservation. */ ++ hcd->periodic_channels--; ++ } else { ++ for (i = 0; i < 8; i++) { ++ hcd->frame_usecs[i] += qh->frame_usecs[i]; ++ qh->frame_usecs[i] = 0; ++ } ++ } ++} ++ ++/** ++ * Removes a QH from either the non-periodic or periodic schedule. Memory is ++ * not freed. ++ * ++ * @param hcd The HCD state structure. ++ * @param qh QH to remove from schedule. */ ++void dwc_otg_hcd_qh_remove(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh) ++{ ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ if (DWC_LIST_EMPTY(&qh->qh_list_entry)) { ++ /* QH is not in a schedule. */ ++ return; ++ } ++ ++ if (dwc_qh_is_non_per(qh)) { ++ if (hcd->non_periodic_qh_ptr == &qh->qh_list_entry) { ++ hcd->non_periodic_qh_ptr = ++ hcd->non_periodic_qh_ptr->next; ++ } ++ DWC_LIST_REMOVE_INIT(&qh->qh_list_entry); ++ //if (!DWC_LIST_EMPTY(&hcd->non_periodic_sched_inactive)) ++ // hcd->fiq_state->kick_np_queues = 1; ++ } else { ++ deschedule_periodic(hcd, qh); ++ hcd->periodic_qh_count--; ++ if( !hcd->periodic_qh_count && !fiq_fsm_enable ) { ++ intr_mask.b.sofintr = 1; ++ if (fiq_enable) { ++ local_fiq_disable(); ++ fiq_fsm_spin_lock(&hcd->fiq_state->lock); ++ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, intr_mask.d32, 0); ++ fiq_fsm_spin_unlock(&hcd->fiq_state->lock); ++ local_fiq_enable(); ++ } else { ++ DWC_MODIFY_REG32(&hcd->core_if->core_global_regs->gintmsk, intr_mask.d32, 0); ++ } ++ } ++ } ++} ++ ++/** ++ * Deactivates a QH. For non-periodic QHs, removes the QH from the active ++ * non-periodic schedule. The QH is added to the inactive non-periodic ++ * schedule if any QTDs are still attached to the QH. ++ * ++ * For periodic QHs, the QH is removed from the periodic queued schedule. If ++ * there are any QTDs still attached to the QH, the QH is added to either the ++ * periodic inactive schedule or the periodic ready schedule and its next ++ * scheduled frame is calculated. The QH is placed in the ready schedule if ++ * the scheduled frame has been reached already. Otherwise it's placed in the ++ * inactive schedule. If there are no QTDs attached to the QH, the QH is ++ * completely removed from the periodic schedule. ++ */ ++void dwc_otg_hcd_qh_deactivate(dwc_otg_hcd_t * hcd, dwc_otg_qh_t * qh, ++ int sched_next_periodic_split) ++{ ++ if (dwc_qh_is_non_per(qh)) { ++ dwc_otg_hcd_qh_remove(hcd, qh); ++ if (!DWC_CIRCLEQ_EMPTY(&qh->qtd_list)) { ++ /* Add back to inactive non-periodic schedule. */ ++ dwc_otg_hcd_qh_add(hcd, qh); ++ //hcd->fiq_state->kick_np_queues = 1; ++ } else { ++ if(nak_holdoff && qh->do_split) { ++ qh->nak_frame = 0xFFFF; ++ } ++ } ++ } else { ++ uint16_t frame_number = dwc_otg_hcd_get_frame_number(hcd); ++ ++ if (qh->do_split) { ++ /* Schedule the next continuing periodic split transfer */ ++ if (sched_next_periodic_split) { ++ ++ qh->sched_frame = frame_number; ++ ++ if (dwc_frame_num_le(frame_number, ++ dwc_frame_num_inc ++ (qh->start_split_frame, ++ 1))) { ++ /* ++ * Allow one frame to elapse after start ++ * split microframe before scheduling ++ * complete split, but DONT if we are ++ * doing the next start split in the ++ * same frame for an ISOC out. ++ */ ++ if ((qh->ep_type != UE_ISOCHRONOUS) || ++ (qh->ep_is_in != 0)) { ++ qh->sched_frame = ++ dwc_frame_num_inc(qh->sched_frame, 1); ++ } ++ } ++ } else { ++ qh->sched_frame = ++ dwc_frame_num_inc(qh->start_split_frame, ++ qh->interval); ++ if (dwc_frame_num_le ++ (qh->sched_frame, frame_number)) { ++ qh->sched_frame = frame_number; ++ } ++ qh->sched_frame |= 0x7; ++ qh->start_split_frame = qh->sched_frame; ++ } ++ } else { ++ qh->sched_frame = ++ dwc_frame_num_inc(qh->sched_frame, qh->interval); ++ if (dwc_frame_num_le(qh->sched_frame, frame_number)) { ++ qh->sched_frame = frame_number; ++ } ++ } ++ ++ if (DWC_CIRCLEQ_EMPTY(&qh->qtd_list)) { ++ dwc_otg_hcd_qh_remove(hcd, qh); ++ } else { ++ /* ++ * Remove from periodic_sched_queued and move to ++ * appropriate queue. ++ */ ++ if ((microframe_schedule && dwc_frame_num_le(qh->sched_frame, frame_number)) || ++ (!microframe_schedule && qh->sched_frame == frame_number)) { ++ DWC_LIST_MOVE_HEAD(&hcd->periodic_sched_ready, ++ &qh->qh_list_entry); ++ } else { ++ if(fiq_enable && !dwc_frame_num_le(hcd->fiq_state->next_sched_frame, qh->sched_frame)) ++ { ++ hcd->fiq_state->next_sched_frame = qh->sched_frame; ++ } ++ ++ DWC_LIST_MOVE_HEAD ++ (&hcd->periodic_sched_inactive, ++ &qh->qh_list_entry); ++ } ++ } ++ } ++} ++ ++/** ++ * This function allocates and initializes a QTD. ++ * ++ * @param urb The URB to create a QTD from. Each URB-QTD pair will end up ++ * pointing to each other so each pair should have a unique correlation. ++ * @param atomic_alloc Flag to do atomic alloc if needed ++ * ++ * @return Returns pointer to the newly allocated QTD, or NULL on error. */ ++dwc_otg_qtd_t *dwc_otg_hcd_qtd_create(dwc_otg_hcd_urb_t * urb, int atomic_alloc) ++{ ++ dwc_otg_qtd_t *qtd; ++ ++ qtd = dwc_otg_hcd_qtd_alloc(atomic_alloc); ++ if (qtd == NULL) { ++ return NULL; ++ } ++ ++ dwc_otg_hcd_qtd_init(qtd, urb); ++ return qtd; ++} ++ ++/** ++ * Initializes a QTD structure. ++ * ++ * @param qtd The QTD to initialize. ++ * @param urb The URB to use for initialization. */ ++void dwc_otg_hcd_qtd_init(dwc_otg_qtd_t * qtd, dwc_otg_hcd_urb_t * urb) ++{ ++ dwc_memset(qtd, 0, sizeof(dwc_otg_qtd_t)); ++ qtd->urb = urb; ++ if (dwc_otg_hcd_get_pipe_type(&urb->pipe_info) == UE_CONTROL) { ++ /* ++ * The only time the QTD data toggle is used is on the data ++ * phase of control transfers. This phase always starts with ++ * DATA1. ++ */ ++ qtd->data_toggle = DWC_OTG_HC_PID_DATA1; ++ qtd->control_phase = DWC_OTG_CONTROL_SETUP; ++ } ++ ++ /* start split */ ++ qtd->complete_split = 0; ++ qtd->isoc_split_pos = DWC_HCSPLIT_XACTPOS_ALL; ++ qtd->isoc_split_offset = 0; ++ qtd->in_process = 0; ++ ++ /* Store the qtd ptr in the urb to reference what QTD. */ ++ urb->qtd = qtd; ++ return; ++} ++ ++/** ++ * This function adds a QTD to the QTD-list of a QH. It will find the correct ++ * QH to place the QTD into. If it does not find a QH, then it will create a ++ * new QH. If the QH to which the QTD is added is not currently scheduled, it ++ * is placed into the proper schedule based on its EP type. ++ * HCD lock must be held and interrupts must be disabled on entry ++ * ++ * @param[in] qtd The QTD to add ++ * @param[in] hcd The DWC HCD structure ++ * @param[out] qh out parameter to return queue head ++ * @param atomic_alloc Flag to do atomic alloc if needed ++ * ++ * @return 0 if successful, negative error code otherwise. ++ */ ++int dwc_otg_hcd_qtd_add(dwc_otg_qtd_t * qtd, ++ dwc_otg_hcd_t * hcd, dwc_otg_qh_t ** qh, int atomic_alloc) ++{ ++ int retval = 0; ++ dwc_otg_hcd_urb_t *urb = qtd->urb; ++ ++ /* ++ * Get the QH which holds the QTD-list to insert to. Create QH if it ++ * doesn't exist. ++ */ ++ if (*qh == NULL) { ++ *qh = dwc_otg_hcd_qh_create(hcd, urb, atomic_alloc); ++ if (*qh == NULL) { ++ retval = -DWC_E_NO_MEMORY; ++ goto done; ++ } else { ++ if (fiq_enable) ++ hcd->fiq_state->kick_np_queues = 1; ++ } ++ } ++ retval = dwc_otg_hcd_qh_add(hcd, *qh); ++ if (retval == 0) { ++ DWC_CIRCLEQ_INSERT_TAIL(&((*qh)->qtd_list), qtd, ++ qtd_list_entry); ++ qtd->qh = *qh; ++ } ++done: ++ ++ return retval; ++} ++ ++#endif /* DWC_DEVICE_ONLY */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_os_dep.h +@@ -0,0 +1,200 @@ ++#ifndef _DWC_OS_DEP_H_ ++#define _DWC_OS_DEP_H_ ++ ++/** ++ * @file ++ * ++ * This file contains OS dependent structures. ++ * ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++ ++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,20) ++# include ++#endif ++ ++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,21) ++# include ++#else ++# include ++#endif ++ ++#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,24) ++# include ++#else ++# include ++#endif ++ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,20) ++# include ++#endif ++ ++#ifdef PCI_INTERFACE ++# include ++#endif ++ ++#ifdef LM_INTERFACE ++# include ++# include ++# include ++# include ++# if (LINUX_VERSION_CODE < KERNEL_VERSION(2,6,30)) ++# include ++# include ++# include ++# include ++# else ++/* in 2.6.31, at least, we seem to have lost the generic LM infrastructure - ++ here we assume that the machine architecture provides definitions ++ in its own header ++*/ ++# include ++# include ++# endif ++#endif ++ ++#ifdef PLATFORM_INTERFACE ++#include ++#ifdef CONFIG_ARM ++#include ++#endif ++#endif ++ ++/** The OS page size */ ++#define DWC_OS_PAGE_SIZE PAGE_SIZE ++ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,14) ++typedef int gfp_t; ++#endif ++ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,18) ++# define IRQF_SHARED SA_SHIRQ ++#endif ++ ++typedef struct os_dependent { ++ /** Base address returned from ioremap() */ ++ void *base; ++ ++ /** Register offset for Diagnostic API */ ++ uint32_t reg_offset; ++ ++ /** Base address for MPHI peripheral */ ++ void *mphi_base; ++ ++ /** mphi_base actually points to the SWIRQ block */ ++ bool use_swirq; ++ ++ /** IRQ number (<0 if not valid) */ ++ int irq_num; ++ ++ /** FIQ number (<0 if not valid) */ ++ int fiq_num; ++ ++#ifdef LM_INTERFACE ++ struct lm_device *lmdev; ++#elif defined(PCI_INTERFACE) ++ struct pci_dev *pcidev; ++ ++ /** Start address of a PCI region */ ++ resource_size_t rsrc_start; ++ ++ /** Length address of a PCI region */ ++ resource_size_t rsrc_len; ++#elif defined(PLATFORM_INTERFACE) ++ struct platform_device *platformdev; ++#endif ++ ++} os_dependent_t; ++ ++#ifdef __cplusplus ++} ++#endif ++ ++ ++ ++/* Type for the our device on the chosen bus */ ++#if defined(LM_INTERFACE) ++typedef struct lm_device dwc_bus_dev_t; ++#elif defined(PCI_INTERFACE) ++typedef struct pci_dev dwc_bus_dev_t; ++#elif defined(PLATFORM_INTERFACE) ++typedef struct platform_device dwc_bus_dev_t; ++#endif ++ ++/* Helper macro to retrieve drvdata from the device on the chosen bus */ ++#if defined(LM_INTERFACE) ++#define DWC_OTG_BUSDRVDATA(_dev) lm_get_drvdata(_dev) ++#elif defined(PCI_INTERFACE) ++#define DWC_OTG_BUSDRVDATA(_dev) pci_get_drvdata(_dev) ++#elif defined(PLATFORM_INTERFACE) ++#define DWC_OTG_BUSDRVDATA(_dev) platform_get_drvdata(_dev) ++#endif ++ ++/** ++ * Helper macro returning the otg_device structure of a given struct device ++ * ++ * c.f. static dwc_otg_device_t *dwc_otg_drvdev(struct device *_dev) ++ */ ++#ifdef LM_INTERFACE ++#define DWC_OTG_GETDRVDEV(_var, _dev) do { \ ++ struct lm_device *lm_dev = \ ++ container_of(_dev, struct lm_device, dev); \ ++ _var = lm_get_drvdata(lm_dev); \ ++ } while (0) ++ ++#elif defined(PCI_INTERFACE) ++#define DWC_OTG_GETDRVDEV(_var, _dev) do { \ ++ _var = dev_get_drvdata(_dev); \ ++ } while (0) ++ ++#elif defined(PLATFORM_INTERFACE) ++#define DWC_OTG_GETDRVDEV(_var, _dev) do { \ ++ struct platform_device *platform_dev = \ ++ container_of(_dev, struct platform_device, dev); \ ++ _var = platform_get_drvdata(platform_dev); \ ++ } while (0) ++#endif ++ ++ ++/** ++ * Helper macro returning the struct dev of the given struct os_dependent ++ * ++ * c.f. static struct device *dwc_otg_getdev(struct os_dependent *osdep) ++ */ ++#ifdef LM_INTERFACE ++#define DWC_OTG_OS_GETDEV(_osdep) \ ++ ((_osdep).lmdev == NULL? NULL: &(_osdep).lmdev->dev) ++#elif defined(PCI_INTERFACE) ++#define DWC_OTG_OS_GETDEV(_osdep) \ ++ ((_osdep).pci_dev == NULL? NULL: &(_osdep).pci_dev->dev) ++#elif defined(PLATFORM_INTERFACE) ++#define DWC_OTG_OS_GETDEV(_osdep) \ ++ ((_osdep).platformdev == NULL? NULL: &(_osdep).platformdev->dev) ++#endif ++ ++ ++ ++ ++#endif /* _DWC_OS_DEP_H_ */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_pcd.c +@@ -0,0 +1,2725 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_pcd.c $ ++ * $Revision: #101 $ ++ * $Date: 2012/08/10 $ ++ * $Change: 2047372 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++#ifndef DWC_HOST_ONLY ++ ++/** @file ++ * This file implements PCD Core. All code in this file is portable and doesn't ++ * use any OS specific functions. ++ * PCD Core provides Interface, defined in ++ * header file, which can be used to implement OS specific PCD interface. ++ * ++ * An important function of the PCD is managing interrupts generated ++ * by the DWC_otg controller. The implementation of the DWC_otg device ++ * mode interrupt service routines is in dwc_otg_pcd_intr.c. ++ * ++ * @todo Add Device Mode test modes (Test J mode, Test K mode, etc). ++ * @todo Does it work when the request size is greater than DEPTSIZ ++ * transfer size ++ * ++ */ ++ ++#include "dwc_otg_pcd.h" ++ ++#ifdef DWC_UTE_CFI ++#include "dwc_otg_cfi.h" ++ ++extern int init_cfi(cfiobject_t * cfiobj); ++#endif ++ ++/** ++ * Choose endpoint from ep arrays using usb_ep structure. ++ */ ++static dwc_otg_pcd_ep_t *get_ep_from_handle(dwc_otg_pcd_t * pcd, void *handle) ++{ ++ int i; ++ if (pcd->ep0.priv == handle) { ++ return &pcd->ep0; ++ } ++ for (i = 0; i < MAX_EPS_CHANNELS - 1; i++) { ++ if (pcd->in_ep[i].priv == handle) ++ return &pcd->in_ep[i]; ++ if (pcd->out_ep[i].priv == handle) ++ return &pcd->out_ep[i]; ++ } ++ ++ return NULL; ++} ++ ++/** ++ * This function completes a request. It call's the request call back. ++ */ ++void dwc_otg_request_done(dwc_otg_pcd_ep_t * ep, dwc_otg_pcd_request_t * req, ++ int32_t status) ++{ ++ unsigned stopped = ep->stopped; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s(ep %p req %p)\n", __func__, ep, req); ++ DWC_CIRCLEQ_REMOVE_INIT(&ep->queue, req, queue_entry); ++ ++ /* don't modify queue heads during completion callback */ ++ ep->stopped = 1; ++ /* spin_unlock/spin_lock now done in fops->complete() */ ++ ep->pcd->fops->complete(ep->pcd, ep->priv, req->priv, status, ++ req->actual); ++ ++ if (ep->pcd->request_pending > 0) { ++ --ep->pcd->request_pending; ++ } ++ ++ ep->stopped = stopped; ++ DWC_FREE(req); ++} ++ ++/** ++ * This function terminates all the requsts in the EP request queue. ++ */ ++void dwc_otg_request_nuke(dwc_otg_pcd_ep_t * ep) ++{ ++ dwc_otg_pcd_request_t *req; ++ ++ ep->stopped = 1; ++ ++ /* called with irqs blocked?? */ ++ while (!DWC_CIRCLEQ_EMPTY(&ep->queue)) { ++ req = DWC_CIRCLEQ_FIRST(&ep->queue); ++ dwc_otg_request_done(ep, req, -DWC_E_SHUTDOWN); ++ } ++} ++ ++void dwc_otg_pcd_start(dwc_otg_pcd_t * pcd, ++ const struct dwc_otg_pcd_function_ops *fops) ++{ ++ pcd->fops = fops; ++} ++ ++/** ++ * PCD Callback function for initializing the PCD when switching to ++ * device mode. ++ * ++ * @param p void pointer to the dwc_otg_pcd_t ++ */ ++static int32_t dwc_otg_pcd_start_cb(void *p) ++{ ++ dwc_otg_pcd_t *pcd = (dwc_otg_pcd_t *) p; ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ ++ /* ++ * Initialized the Core for Device mode. ++ */ ++ if (dwc_otg_is_device_mode(core_if)) { ++ dwc_otg_core_dev_init(core_if); ++ /* Set core_if's lock pointer to the pcd->lock */ ++ core_if->lock = pcd->lock; ++ } ++ return 1; ++} ++ ++/** CFI-specific buffer allocation function for EP */ ++#ifdef DWC_UTE_CFI ++uint8_t *cfiw_ep_alloc_buffer(dwc_otg_pcd_t * pcd, void *pep, dwc_dma_t * addr, ++ size_t buflen, int flags) ++{ ++ dwc_otg_pcd_ep_t *ep; ++ ep = get_ep_from_handle(pcd, pep); ++ if (!ep) { ++ DWC_WARN("bad ep\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ return pcd->cfi->ops.ep_alloc_buf(pcd->cfi, pcd, ep, addr, buflen, ++ flags); ++} ++#else ++uint8_t *cfiw_ep_alloc_buffer(dwc_otg_pcd_t * pcd, void *pep, dwc_dma_t * addr, ++ size_t buflen, int flags); ++#endif ++ ++/** ++ * PCD Callback function for notifying the PCD when resuming from ++ * suspend. ++ * ++ * @param p void pointer to the dwc_otg_pcd_t ++ */ ++static int32_t dwc_otg_pcd_resume_cb(void *p) ++{ ++ dwc_otg_pcd_t *pcd = (dwc_otg_pcd_t *) p; ++ ++ if (pcd->fops->resume) { ++ pcd->fops->resume(pcd); ++ } ++ ++ /* Stop the SRP timeout timer. */ ++ if ((GET_CORE_IF(pcd)->core_params->phy_type != DWC_PHY_TYPE_PARAM_FS) ++ || (!GET_CORE_IF(pcd)->core_params->i2c_enable)) { ++ if (GET_CORE_IF(pcd)->srp_timer_started) { ++ GET_CORE_IF(pcd)->srp_timer_started = 0; ++ DWC_TIMER_CANCEL(GET_CORE_IF(pcd)->srp_timer); ++ } ++ } ++ return 1; ++} ++ ++/** ++ * PCD Callback function for notifying the PCD device is suspended. ++ * ++ * @param p void pointer to the dwc_otg_pcd_t ++ */ ++static int32_t dwc_otg_pcd_suspend_cb(void *p) ++{ ++ dwc_otg_pcd_t *pcd = (dwc_otg_pcd_t *) p; ++ ++ if (pcd->fops->suspend) { ++ DWC_SPINUNLOCK(pcd->lock); ++ pcd->fops->suspend(pcd); ++ DWC_SPINLOCK(pcd->lock); ++ } ++ ++ return 1; ++} ++ ++/** ++ * PCD Callback function for stopping the PCD when switching to Host ++ * mode. ++ * ++ * @param p void pointer to the dwc_otg_pcd_t ++ */ ++static int32_t dwc_otg_pcd_stop_cb(void *p) ++{ ++ dwc_otg_pcd_t *pcd = (dwc_otg_pcd_t *) p; ++ extern void dwc_otg_pcd_stop(dwc_otg_pcd_t * _pcd); ++ ++ dwc_otg_pcd_stop(pcd); ++ return 1; ++} ++ ++/** ++ * PCD Callback structure for handling mode switching. ++ */ ++static dwc_otg_cil_callbacks_t pcd_callbacks = { ++ .start = dwc_otg_pcd_start_cb, ++ .stop = dwc_otg_pcd_stop_cb, ++ .suspend = dwc_otg_pcd_suspend_cb, ++ .resume_wakeup = dwc_otg_pcd_resume_cb, ++ .p = 0, /* Set at registration */ ++}; ++ ++/** ++ * This function allocates a DMA Descriptor chain for the Endpoint ++ * buffer to be used for a transfer to/from the specified endpoint. ++ */ ++dwc_otg_dev_dma_desc_t *dwc_otg_ep_alloc_desc_chain(struct device *dev, ++ dwc_dma_t * dma_desc_addr, ++ uint32_t count) ++{ ++ return DWC_DMA_ALLOC_ATOMIC(dev, count * sizeof(dwc_otg_dev_dma_desc_t), ++ dma_desc_addr); ++} ++ ++/** ++ * This function frees a DMA Descriptor chain that was allocated by ep_alloc_desc. ++ */ ++void dwc_otg_ep_free_desc_chain(struct device *dev, ++ dwc_otg_dev_dma_desc_t * desc_addr, ++ uint32_t dma_desc_addr, uint32_t count) ++{ ++ DWC_DMA_FREE(dev, count * sizeof(dwc_otg_dev_dma_desc_t), desc_addr, ++ dma_desc_addr); ++} ++ ++#ifdef DWC_EN_ISOC ++ ++/** ++ * This function initializes a descriptor chain for Isochronous transfer ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param dwc_ep The EP to start the transfer on. ++ * ++ */ ++void dwc_otg_iso_ep_start_ddma_transfer(dwc_otg_core_if_t * core_if, ++ dwc_ep_t * dwc_ep) ++{ ++ ++ dsts_data_t dsts = {.d32 = 0 }; ++ depctl_data_t depctl = {.d32 = 0 }; ++ volatile uint32_t *addr; ++ int i, j; ++ uint32_t len; ++ ++ if (dwc_ep->is_in) ++ dwc_ep->desc_cnt = dwc_ep->buf_proc_intrvl / dwc_ep->bInterval; ++ else ++ dwc_ep->desc_cnt = ++ dwc_ep->buf_proc_intrvl * dwc_ep->pkt_per_frm / ++ dwc_ep->bInterval; ++ ++ /** Allocate descriptors for double buffering */ ++ dwc_ep->iso_desc_addr = ++ dwc_otg_ep_alloc_desc_chain(&dwc_ep->iso_dma_desc_addr, ++ dwc_ep->desc_cnt * 2); ++ if (dwc_ep->desc_addr) { ++ DWC_WARN("%s, can't allocate DMA descriptor chain\n", __func__); ++ return; ++ } ++ ++ dsts.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts); ++ ++ /** ISO OUT EP */ ++ if (dwc_ep->is_in == 0) { ++ dev_dma_desc_sts_t sts = {.d32 = 0 }; ++ dwc_otg_dev_dma_desc_t *dma_desc = dwc_ep->iso_desc_addr; ++ dma_addr_t dma_ad; ++ uint32_t data_per_desc; ++ dwc_otg_dev_out_ep_regs_t *out_regs = ++ core_if->dev_if->out_ep_regs[dwc_ep->num]; ++ int offset; ++ ++ addr = &core_if->dev_if->out_ep_regs[dwc_ep->num]->doepctl; ++ dma_ad = (dma_addr_t) DWC_READ_REG32(&(out_regs->doepdma)); ++ ++ /** Buffer 0 descriptors setup */ ++ dma_ad = dwc_ep->dma_addr0; ++ ++ sts.b_iso_out.bs = BS_HOST_READY; ++ sts.b_iso_out.rxsts = 0; ++ sts.b_iso_out.l = 0; ++ sts.b_iso_out.sp = 0; ++ sts.b_iso_out.ioc = 0; ++ sts.b_iso_out.pid = 0; ++ sts.b_iso_out.framenum = 0; ++ ++ offset = 0; ++ for (i = 0; i < dwc_ep->desc_cnt - dwc_ep->pkt_per_frm; ++ i += dwc_ep->pkt_per_frm) { ++ ++ for (j = 0; j < dwc_ep->pkt_per_frm; ++j) { ++ uint32_t len = (j + 1) * dwc_ep->maxpacket; ++ if (len > dwc_ep->data_per_frame) ++ data_per_desc = ++ dwc_ep->data_per_frame - ++ j * dwc_ep->maxpacket; ++ else ++ data_per_desc = dwc_ep->maxpacket; ++ len = data_per_desc % 4; ++ if (len) ++ data_per_desc += 4 - len; ++ ++ sts.b_iso_out.rxbytes = data_per_desc; ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ ++ offset += data_per_desc; ++ dma_desc++; ++ dma_ad += data_per_desc; ++ } ++ } ++ ++ for (j = 0; j < dwc_ep->pkt_per_frm - 1; ++j) { ++ uint32_t len = (j + 1) * dwc_ep->maxpacket; ++ if (len > dwc_ep->data_per_frame) ++ data_per_desc = ++ dwc_ep->data_per_frame - ++ j * dwc_ep->maxpacket; ++ else ++ data_per_desc = dwc_ep->maxpacket; ++ len = data_per_desc % 4; ++ if (len) ++ data_per_desc += 4 - len; ++ sts.b_iso_out.rxbytes = data_per_desc; ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ ++ offset += data_per_desc; ++ dma_desc++; ++ dma_ad += data_per_desc; ++ } ++ ++ sts.b_iso_out.ioc = 1; ++ len = (j + 1) * dwc_ep->maxpacket; ++ if (len > dwc_ep->data_per_frame) ++ data_per_desc = ++ dwc_ep->data_per_frame - j * dwc_ep->maxpacket; ++ else ++ data_per_desc = dwc_ep->maxpacket; ++ len = data_per_desc % 4; ++ if (len) ++ data_per_desc += 4 - len; ++ sts.b_iso_out.rxbytes = data_per_desc; ++ ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ dma_desc++; ++ ++ /** Buffer 1 descriptors setup */ ++ sts.b_iso_out.ioc = 0; ++ dma_ad = dwc_ep->dma_addr1; ++ ++ offset = 0; ++ for (i = 0; i < dwc_ep->desc_cnt - dwc_ep->pkt_per_frm; ++ i += dwc_ep->pkt_per_frm) { ++ for (j = 0; j < dwc_ep->pkt_per_frm; ++j) { ++ uint32_t len = (j + 1) * dwc_ep->maxpacket; ++ if (len > dwc_ep->data_per_frame) ++ data_per_desc = ++ dwc_ep->data_per_frame - ++ j * dwc_ep->maxpacket; ++ else ++ data_per_desc = dwc_ep->maxpacket; ++ len = data_per_desc % 4; ++ if (len) ++ data_per_desc += 4 - len; ++ ++ data_per_desc = ++ sts.b_iso_out.rxbytes = data_per_desc; ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ ++ offset += data_per_desc; ++ dma_desc++; ++ dma_ad += data_per_desc; ++ } ++ } ++ for (j = 0; j < dwc_ep->pkt_per_frm - 1; ++j) { ++ data_per_desc = ++ ((j + 1) * dwc_ep->maxpacket > ++ dwc_ep->data_per_frame) ? dwc_ep->data_per_frame - ++ j * dwc_ep->maxpacket : dwc_ep->maxpacket; ++ data_per_desc += ++ (data_per_desc % 4) ? (4 - data_per_desc % 4) : 0; ++ sts.b_iso_out.rxbytes = data_per_desc; ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ ++ offset += data_per_desc; ++ dma_desc++; ++ dma_ad += data_per_desc; ++ } ++ ++ sts.b_iso_out.ioc = 1; ++ sts.b_iso_out.l = 1; ++ data_per_desc = ++ ((j + 1) * dwc_ep->maxpacket > ++ dwc_ep->data_per_frame) ? dwc_ep->data_per_frame - ++ j * dwc_ep->maxpacket : dwc_ep->maxpacket; ++ data_per_desc += ++ (data_per_desc % 4) ? (4 - data_per_desc % 4) : 0; ++ sts.b_iso_out.rxbytes = data_per_desc; ++ ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ ++ dwc_ep->next_frame = 0; ++ ++ /** Write dma_ad into DOEPDMA register */ ++ DWC_WRITE_REG32(&(out_regs->doepdma), ++ (uint32_t) dwc_ep->iso_dma_desc_addr); ++ ++ } ++ /** ISO IN EP */ ++ else { ++ dev_dma_desc_sts_t sts = {.d32 = 0 }; ++ dwc_otg_dev_dma_desc_t *dma_desc = dwc_ep->iso_desc_addr; ++ dma_addr_t dma_ad; ++ dwc_otg_dev_in_ep_regs_t *in_regs = ++ core_if->dev_if->in_ep_regs[dwc_ep->num]; ++ unsigned int frmnumber; ++ fifosize_data_t txfifosize, rxfifosize; ++ ++ txfifosize.d32 = ++ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[dwc_ep->num]-> ++ dtxfsts); ++ rxfifosize.d32 = ++ DWC_READ_REG32(&core_if->core_global_regs->grxfsiz); ++ ++ addr = &core_if->dev_if->in_ep_regs[dwc_ep->num]->diepctl; ++ ++ dma_ad = dwc_ep->dma_addr0; ++ ++ dsts.d32 = ++ DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts); ++ ++ sts.b_iso_in.bs = BS_HOST_READY; ++ sts.b_iso_in.txsts = 0; ++ sts.b_iso_in.sp = ++ (dwc_ep->data_per_frame % dwc_ep->maxpacket) ? 1 : 0; ++ sts.b_iso_in.ioc = 0; ++ sts.b_iso_in.pid = dwc_ep->pkt_per_frm; ++ ++ frmnumber = dwc_ep->next_frame; ++ ++ sts.b_iso_in.framenum = frmnumber; ++ sts.b_iso_in.txbytes = dwc_ep->data_per_frame; ++ sts.b_iso_in.l = 0; ++ ++ /** Buffer 0 descriptors setup */ ++ for (i = 0; i < dwc_ep->desc_cnt - 1; i++) { ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ dma_desc++; ++ ++ dma_ad += dwc_ep->data_per_frame; ++ sts.b_iso_in.framenum += dwc_ep->bInterval; ++ } ++ ++ sts.b_iso_in.ioc = 1; ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ ++dma_desc; ++ ++ /** Buffer 1 descriptors setup */ ++ sts.b_iso_in.ioc = 0; ++ dma_ad = dwc_ep->dma_addr1; ++ ++ for (i = 0; i < dwc_ep->desc_cnt - dwc_ep->pkt_per_frm; ++ i += dwc_ep->pkt_per_frm) { ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ dma_desc++; ++ ++ dma_ad += dwc_ep->data_per_frame; ++ sts.b_iso_in.framenum += dwc_ep->bInterval; ++ ++ sts.b_iso_in.ioc = 0; ++ } ++ sts.b_iso_in.ioc = 1; ++ sts.b_iso_in.l = 1; ++ ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ ++ dwc_ep->next_frame = sts.b_iso_in.framenum + dwc_ep->bInterval; ++ ++ /** Write dma_ad into diepdma register */ ++ DWC_WRITE_REG32(&(in_regs->diepdma), ++ (uint32_t) dwc_ep->iso_dma_desc_addr); ++ } ++ /** Enable endpoint, clear nak */ ++ depctl.d32 = 0; ++ depctl.b.epena = 1; ++ depctl.b.usbactep = 1; ++ depctl.b.cnak = 1; ++ ++ DWC_MODIFY_REG32(addr, depctl.d32, depctl.d32); ++ depctl.d32 = DWC_READ_REG32(addr); ++} ++ ++/** ++ * This function initializes a descriptor chain for Isochronous transfer ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to start the transfer on. ++ * ++ */ ++void dwc_otg_iso_ep_start_buf_transfer(dwc_otg_core_if_t * core_if, ++ dwc_ep_t * ep) ++{ ++ depctl_data_t depctl = {.d32 = 0 }; ++ volatile uint32_t *addr; ++ ++ if (ep->is_in) { ++ addr = &core_if->dev_if->in_ep_regs[ep->num]->diepctl; ++ } else { ++ addr = &core_if->dev_if->out_ep_regs[ep->num]->doepctl; ++ } ++ ++ if (core_if->dma_enable == 0 || core_if->dma_desc_enable != 0) { ++ return; ++ } else { ++ deptsiz_data_t deptsiz = {.d32 = 0 }; ++ ++ ep->xfer_len = ++ ep->data_per_frame * ep->buf_proc_intrvl / ep->bInterval; ++ ep->pkt_cnt = ++ (ep->xfer_len - 1 + ep->maxpacket) / ep->maxpacket; ++ ep->xfer_count = 0; ++ ep->xfer_buff = ++ (ep->proc_buf_num) ? ep->xfer_buff1 : ep->xfer_buff0; ++ ep->dma_addr = ++ (ep->proc_buf_num) ? ep->dma_addr1 : ep->dma_addr0; ++ ++ if (ep->is_in) { ++ /* Program the transfer size and packet count ++ * as follows: xfersize = N * maxpacket + ++ * short_packet pktcnt = N + (short_packet ++ * exist ? 1 : 0) ++ */ ++ deptsiz.b.mc = ep->pkt_per_frm; ++ deptsiz.b.xfersize = ep->xfer_len; ++ deptsiz.b.pktcnt = ++ (ep->xfer_len - 1 + ep->maxpacket) / ep->maxpacket; ++ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[ep->num]-> ++ dieptsiz, deptsiz.d32); ++ ++ /* Write the DMA register */ ++ DWC_WRITE_REG32(& ++ (core_if->dev_if->in_ep_regs[ep->num]-> ++ diepdma), (uint32_t) ep->dma_addr); ++ ++ } else { ++ deptsiz.b.pktcnt = ++ (ep->xfer_len + (ep->maxpacket - 1)) / ++ ep->maxpacket; ++ deptsiz.b.xfersize = deptsiz.b.pktcnt * ep->maxpacket; ++ ++ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[ep->num]-> ++ doeptsiz, deptsiz.d32); ++ ++ /* Write the DMA register */ ++ DWC_WRITE_REG32(& ++ (core_if->dev_if->out_ep_regs[ep->num]-> ++ doepdma), (uint32_t) ep->dma_addr); ++ ++ } ++ /** Enable endpoint, clear nak */ ++ depctl.d32 = 0; ++ depctl.b.epena = 1; ++ depctl.b.cnak = 1; ++ ++ DWC_MODIFY_REG32(addr, depctl.d32, depctl.d32); ++ } ++} ++ ++/** ++ * This function does the setup for a data transfer for an EP and ++ * starts the transfer. For an IN transfer, the packets will be ++ * loaded into the appropriate Tx FIFO in the ISR. For OUT transfers, ++ * the packets are unloaded from the Rx FIFO in the ISR. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to start the transfer on. ++ */ ++ ++static void dwc_otg_iso_ep_start_transfer(dwc_otg_core_if_t * core_if, ++ dwc_ep_t * ep) ++{ ++ if (core_if->dma_enable) { ++ if (core_if->dma_desc_enable) { ++ if (ep->is_in) { ++ ep->desc_cnt = ep->pkt_cnt / ep->pkt_per_frm; ++ } else { ++ ep->desc_cnt = ep->pkt_cnt; ++ } ++ dwc_otg_iso_ep_start_ddma_transfer(core_if, ep); ++ } else { ++ if (core_if->pti_enh_enable) { ++ dwc_otg_iso_ep_start_buf_transfer(core_if, ep); ++ } else { ++ ep->cur_pkt_addr = ++ (ep->proc_buf_num) ? ep->xfer_buff1 : ep-> ++ xfer_buff0; ++ ep->cur_pkt_dma_addr = ++ (ep->proc_buf_num) ? ep->dma_addr1 : ep-> ++ dma_addr0; ++ dwc_otg_iso_ep_start_frm_transfer(core_if, ep); ++ } ++ } ++ } else { ++ ep->cur_pkt_addr = ++ (ep->proc_buf_num) ? ep->xfer_buff1 : ep->xfer_buff0; ++ ep->cur_pkt_dma_addr = ++ (ep->proc_buf_num) ? ep->dma_addr1 : ep->dma_addr0; ++ dwc_otg_iso_ep_start_frm_transfer(core_if, ep); ++ } ++} ++ ++/** ++ * This function stops transfer for an EP and ++ * resets the ep's variables. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to start the transfer on. ++ */ ++ ++void dwc_otg_iso_ep_stop_transfer(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ depctl_data_t depctl = {.d32 = 0 }; ++ volatile uint32_t *addr; ++ ++ if (ep->is_in == 1) { ++ addr = &core_if->dev_if->in_ep_regs[ep->num]->diepctl; ++ } else { ++ addr = &core_if->dev_if->out_ep_regs[ep->num]->doepctl; ++ } ++ ++ /* disable the ep */ ++ depctl.d32 = DWC_READ_REG32(addr); ++ ++ depctl.b.epdis = 1; ++ depctl.b.snak = 1; ++ ++ DWC_WRITE_REG32(addr, depctl.d32); ++ ++ if (core_if->dma_desc_enable && ++ ep->iso_desc_addr && ep->iso_dma_desc_addr) { ++ dwc_otg_ep_free_desc_chain(ep->iso_desc_addr, ++ ep->iso_dma_desc_addr, ++ ep->desc_cnt * 2); ++ } ++ ++ /* reset varibales */ ++ ep->dma_addr0 = 0; ++ ep->dma_addr1 = 0; ++ ep->xfer_buff0 = 0; ++ ep->xfer_buff1 = 0; ++ ep->data_per_frame = 0; ++ ep->data_pattern_frame = 0; ++ ep->sync_frame = 0; ++ ep->buf_proc_intrvl = 0; ++ ep->bInterval = 0; ++ ep->proc_buf_num = 0; ++ ep->pkt_per_frm = 0; ++ ep->pkt_per_frm = 0; ++ ep->desc_cnt = 0; ++ ep->iso_desc_addr = 0; ++ ep->iso_dma_desc_addr = 0; ++} ++ ++int dwc_otg_pcd_iso_ep_start(dwc_otg_pcd_t * pcd, void *ep_handle, ++ uint8_t * buf0, uint8_t * buf1, dwc_dma_t dma0, ++ dwc_dma_t dma1, int sync_frame, int dp_frame, ++ int data_per_frame, int start_frame, ++ int buf_proc_intrvl, void *req_handle, ++ int atomic_alloc) ++{ ++ dwc_otg_pcd_ep_t *ep; ++ dwc_irqflags_t flags = 0; ++ dwc_ep_t *dwc_ep; ++ int32_t frm_data; ++ dsts_data_t dsts; ++ dwc_otg_core_if_t *core_if; ++ ++ ep = get_ep_from_handle(pcd, ep_handle); ++ ++ if (!ep || !ep->desc || ep->dwc_ep.num == 0) { ++ DWC_WARN("bad ep\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags); ++ core_if = GET_CORE_IF(pcd); ++ dwc_ep = &ep->dwc_ep; ++ ++ if (ep->iso_req_handle) { ++ DWC_WARN("ISO request in progress\n"); ++ } ++ ++ dwc_ep->dma_addr0 = dma0; ++ dwc_ep->dma_addr1 = dma1; ++ ++ dwc_ep->xfer_buff0 = buf0; ++ dwc_ep->xfer_buff1 = buf1; ++ ++ dwc_ep->data_per_frame = data_per_frame; ++ ++ /** @todo - pattern data support is to be implemented in the future */ ++ dwc_ep->data_pattern_frame = dp_frame; ++ dwc_ep->sync_frame = sync_frame; ++ ++ dwc_ep->buf_proc_intrvl = buf_proc_intrvl; ++ ++ dwc_ep->bInterval = 1 << (ep->desc->bInterval - 1); ++ ++ dwc_ep->proc_buf_num = 0; ++ ++ dwc_ep->pkt_per_frm = 0; ++ frm_data = ep->dwc_ep.data_per_frame; ++ while (frm_data > 0) { ++ dwc_ep->pkt_per_frm++; ++ frm_data -= ep->dwc_ep.maxpacket; ++ } ++ ++ dsts.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts); ++ ++ if (start_frame == -1) { ++ dwc_ep->next_frame = dsts.b.soffn + 1; ++ if (dwc_ep->bInterval != 1) { ++ dwc_ep->next_frame = ++ dwc_ep->next_frame + (dwc_ep->bInterval - 1 - ++ dwc_ep->next_frame % ++ dwc_ep->bInterval); ++ } ++ } else { ++ dwc_ep->next_frame = start_frame; ++ } ++ ++ if (!core_if->pti_enh_enable) { ++ dwc_ep->pkt_cnt = ++ dwc_ep->buf_proc_intrvl * dwc_ep->pkt_per_frm / ++ dwc_ep->bInterval; ++ } else { ++ dwc_ep->pkt_cnt = ++ (dwc_ep->data_per_frame * ++ (dwc_ep->buf_proc_intrvl / dwc_ep->bInterval) ++ - 1 + dwc_ep->maxpacket) / dwc_ep->maxpacket; ++ } ++ ++ if (core_if->dma_desc_enable) { ++ dwc_ep->desc_cnt = ++ dwc_ep->buf_proc_intrvl * dwc_ep->pkt_per_frm / ++ dwc_ep->bInterval; ++ } ++ ++ if (atomic_alloc) { ++ dwc_ep->pkt_info = ++ DWC_ALLOC_ATOMIC(sizeof(iso_pkt_info_t) * dwc_ep->pkt_cnt); ++ } else { ++ dwc_ep->pkt_info = ++ DWC_ALLOC(sizeof(iso_pkt_info_t) * dwc_ep->pkt_cnt); ++ } ++ if (!dwc_ep->pkt_info) { ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ return -DWC_E_NO_MEMORY; ++ } ++ if (core_if->pti_enh_enable) { ++ dwc_memset(dwc_ep->pkt_info, 0, ++ sizeof(iso_pkt_info_t) * dwc_ep->pkt_cnt); ++ } ++ ++ dwc_ep->cur_pkt = 0; ++ ep->iso_req_handle = req_handle; ++ ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ dwc_otg_iso_ep_start_transfer(core_if, dwc_ep); ++ return 0; ++} ++ ++int dwc_otg_pcd_iso_ep_stop(dwc_otg_pcd_t * pcd, void *ep_handle, ++ void *req_handle) ++{ ++ dwc_irqflags_t flags = 0; ++ dwc_otg_pcd_ep_t *ep; ++ dwc_ep_t *dwc_ep; ++ ++ ep = get_ep_from_handle(pcd, ep_handle); ++ if (!ep || !ep->desc || ep->dwc_ep.num == 0) { ++ DWC_WARN("bad ep\n"); ++ return -DWC_E_INVALID; ++ } ++ dwc_ep = &ep->dwc_ep; ++ ++ dwc_otg_iso_ep_stop_transfer(GET_CORE_IF(pcd), dwc_ep); ++ ++ DWC_FREE(dwc_ep->pkt_info); ++ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags); ++ if (ep->iso_req_handle != req_handle) { ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ return -DWC_E_INVALID; ++ } ++ ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ ++ ep->iso_req_handle = 0; ++ return 0; ++} ++ ++/** ++ * This function is used for perodical data exchnage between PCD and gadget drivers. ++ * for Isochronous EPs ++ * ++ * - Every time a sync period completes this function is called to ++ * perform data exchange between PCD and gadget ++ */ ++void dwc_otg_iso_buffer_done(dwc_otg_pcd_t * pcd, dwc_otg_pcd_ep_t * ep, ++ void *req_handle) ++{ ++ int i; ++ dwc_ep_t *dwc_ep; ++ ++ dwc_ep = &ep->dwc_ep; ++ ++ DWC_SPINUNLOCK(ep->pcd->lock); ++ pcd->fops->isoc_complete(pcd, ep->priv, ep->iso_req_handle, ++ dwc_ep->proc_buf_num ^ 0x1); ++ DWC_SPINLOCK(ep->pcd->lock); ++ ++ for (i = 0; i < dwc_ep->pkt_cnt; ++i) { ++ dwc_ep->pkt_info[i].status = 0; ++ dwc_ep->pkt_info[i].offset = 0; ++ dwc_ep->pkt_info[i].length = 0; ++ } ++} ++ ++int dwc_otg_pcd_get_iso_packet_count(dwc_otg_pcd_t * pcd, void *ep_handle, ++ void *iso_req_handle) ++{ ++ dwc_otg_pcd_ep_t *ep; ++ dwc_ep_t *dwc_ep; ++ ++ ep = get_ep_from_handle(pcd, ep_handle); ++ if (!ep->desc || ep->dwc_ep.num == 0) { ++ DWC_WARN("bad ep\n"); ++ return -DWC_E_INVALID; ++ } ++ dwc_ep = &ep->dwc_ep; ++ ++ return dwc_ep->pkt_cnt; ++} ++ ++void dwc_otg_pcd_get_iso_packet_params(dwc_otg_pcd_t * pcd, void *ep_handle, ++ void *iso_req_handle, int packet, ++ int *status, int *actual, int *offset) ++{ ++ dwc_otg_pcd_ep_t *ep; ++ dwc_ep_t *dwc_ep; ++ ++ ep = get_ep_from_handle(pcd, ep_handle); ++ if (!ep) ++ DWC_WARN("bad ep\n"); ++ ++ dwc_ep = &ep->dwc_ep; ++ ++ *status = dwc_ep->pkt_info[packet].status; ++ *actual = dwc_ep->pkt_info[packet].length; ++ *offset = dwc_ep->pkt_info[packet].offset; ++} ++ ++#endif /* DWC_EN_ISOC */ ++ ++static void dwc_otg_pcd_init_ep(dwc_otg_pcd_t * pcd, dwc_otg_pcd_ep_t * pcd_ep, ++ uint32_t is_in, uint32_t ep_num) ++{ ++ /* Init EP structure */ ++ pcd_ep->desc = 0; ++ pcd_ep->pcd = pcd; ++ pcd_ep->stopped = 1; ++ pcd_ep->queue_sof = 0; ++ ++ /* Init DWC ep structure */ ++ pcd_ep->dwc_ep.is_in = is_in; ++ pcd_ep->dwc_ep.num = ep_num; ++ pcd_ep->dwc_ep.active = 0; ++ pcd_ep->dwc_ep.tx_fifo_num = 0; ++ /* Control until ep is actvated */ ++ pcd_ep->dwc_ep.type = DWC_OTG_EP_TYPE_CONTROL; ++ pcd_ep->dwc_ep.maxpacket = MAX_PACKET_SIZE; ++ pcd_ep->dwc_ep.dma_addr = 0; ++ pcd_ep->dwc_ep.start_xfer_buff = 0; ++ pcd_ep->dwc_ep.xfer_buff = 0; ++ pcd_ep->dwc_ep.xfer_len = 0; ++ pcd_ep->dwc_ep.xfer_count = 0; ++ pcd_ep->dwc_ep.sent_zlp = 0; ++ pcd_ep->dwc_ep.total_len = 0; ++ pcd_ep->dwc_ep.desc_addr = 0; ++ pcd_ep->dwc_ep.dma_desc_addr = 0; ++ DWC_CIRCLEQ_INIT(&pcd_ep->queue); ++} ++ ++/** ++ * Initialize ep's ++ */ ++static void dwc_otg_pcd_reinit(dwc_otg_pcd_t * pcd) ++{ ++ int i; ++ uint32_t hwcfg1; ++ dwc_otg_pcd_ep_t *ep; ++ int in_ep_cntr, out_ep_cntr; ++ uint32_t num_in_eps = (GET_CORE_IF(pcd))->dev_if->num_in_eps; ++ uint32_t num_out_eps = (GET_CORE_IF(pcd))->dev_if->num_out_eps; ++ ++ /** ++ * Initialize the EP0 structure. ++ */ ++ ep = &pcd->ep0; ++ dwc_otg_pcd_init_ep(pcd, ep, 0, 0); ++ ++ in_ep_cntr = 0; ++ hwcfg1 = (GET_CORE_IF(pcd))->hwcfg1.d32 >> 3; ++ for (i = 1; in_ep_cntr < num_in_eps; i++) { ++ if ((hwcfg1 & 0x1) == 0) { ++ dwc_otg_pcd_ep_t *ep = &pcd->in_ep[in_ep_cntr]; ++ in_ep_cntr++; ++ /** ++ * @todo NGS: Add direction to EP, based on contents ++ * of HWCFG1. Need a copy of HWCFG1 in pcd structure? ++ * sprintf(";r ++ */ ++ dwc_otg_pcd_init_ep(pcd, ep, 1 /* IN */ , i); ++ ++ DWC_CIRCLEQ_INIT(&ep->queue); ++ } ++ hwcfg1 >>= 2; ++ } ++ ++ out_ep_cntr = 0; ++ hwcfg1 = (GET_CORE_IF(pcd))->hwcfg1.d32 >> 2; ++ for (i = 1; out_ep_cntr < num_out_eps; i++) { ++ if ((hwcfg1 & 0x1) == 0) { ++ dwc_otg_pcd_ep_t *ep = &pcd->out_ep[out_ep_cntr]; ++ out_ep_cntr++; ++ /** ++ * @todo NGS: Add direction to EP, based on contents ++ * of HWCFG1. Need a copy of HWCFG1 in pcd structure? ++ * sprintf(";r ++ */ ++ dwc_otg_pcd_init_ep(pcd, ep, 0 /* OUT */ , i); ++ DWC_CIRCLEQ_INIT(&ep->queue); ++ } ++ hwcfg1 >>= 2; ++ } ++ ++ pcd->ep0state = EP0_DISCONNECT; ++ pcd->ep0.dwc_ep.maxpacket = MAX_EP0_SIZE; ++ pcd->ep0.dwc_ep.type = DWC_OTG_EP_TYPE_CONTROL; ++} ++ ++/** ++ * This function is called when the SRP timer expires. The SRP should ++ * complete within 6 seconds. ++ */ ++static void srp_timeout(void *ptr) ++{ ++ gotgctl_data_t gotgctl; ++ dwc_otg_core_if_t *core_if = (dwc_otg_core_if_t *) ptr; ++ volatile uint32_t *addr = &core_if->core_global_regs->gotgctl; ++ ++ gotgctl.d32 = DWC_READ_REG32(addr); ++ ++ core_if->srp_timer_started = 0; ++ ++ if (core_if->adp_enable) { ++ if (gotgctl.b.bsesvld == 0) { ++ gpwrdn_data_t gpwrdn = {.d32 = 0 }; ++ DWC_PRINTF("SRP Timeout BSESSVLD = 0\n"); ++ /* Power off the core */ ++ if (core_if->power_down == 2) { ++ gpwrdn.b.pwrdnswtch = 1; ++ DWC_MODIFY_REG32(&core_if-> ++ core_global_regs->gpwrdn, ++ gpwrdn.d32, 0); ++ } ++ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuintsel = 1; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gpwrdn, 0, ++ gpwrdn.d32); ++ dwc_otg_adp_probe_start(core_if); ++ } else { ++ DWC_PRINTF("SRP Timeout BSESSVLD = 1\n"); ++ core_if->op_state = B_PERIPHERAL; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_pcd_start(core_if); ++ } ++ } ++ ++ if ((core_if->core_params->phy_type == DWC_PHY_TYPE_PARAM_FS) && ++ (core_if->core_params->i2c_enable)) { ++ DWC_PRINTF("SRP Timeout\n"); ++ ++ if ((core_if->srp_success) && (gotgctl.b.bsesvld)) { ++ if (core_if->pcd_cb && core_if->pcd_cb->resume_wakeup) { ++ core_if->pcd_cb->resume_wakeup(core_if->pcd_cb->p); ++ } ++ ++ /* Clear Session Request */ ++ gotgctl.d32 = 0; ++ gotgctl.b.sesreq = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gotgctl, ++ gotgctl.d32, 0); ++ ++ core_if->srp_success = 0; ++ } else { ++ __DWC_ERROR("Device not connected/responding\n"); ++ gotgctl.b.sesreq = 0; ++ DWC_WRITE_REG32(addr, gotgctl.d32); ++ } ++ } else if (gotgctl.b.sesreq) { ++ DWC_PRINTF("SRP Timeout\n"); ++ ++ __DWC_ERROR("Device not connected/responding\n"); ++ gotgctl.b.sesreq = 0; ++ DWC_WRITE_REG32(addr, gotgctl.d32); ++ } else { ++ DWC_PRINTF(" SRP GOTGCTL=%0x\n", gotgctl.d32); ++ } ++} ++ ++/** ++ * Tasklet ++ * ++ */ ++extern void start_next_request(dwc_otg_pcd_ep_t * ep); ++ ++static void start_xfer_tasklet_func(void *data) ++{ ++ dwc_otg_pcd_t *pcd = (dwc_otg_pcd_t *) data; ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ ++ int i; ++ depctl_data_t diepctl; ++ ++ DWC_DEBUGPL(DBG_PCDV, "Start xfer tasklet\n"); ++ ++ diepctl.d32 = DWC_READ_REG32(&core_if->dev_if->in_ep_regs[0]->diepctl); ++ ++ if (pcd->ep0.queue_sof) { ++ pcd->ep0.queue_sof = 0; ++ start_next_request(&pcd->ep0); ++ // break; ++ } ++ ++ for (i = 0; i < core_if->dev_if->num_in_eps; i++) { ++ depctl_data_t diepctl; ++ diepctl.d32 = ++ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[i]->diepctl); ++ ++ if (pcd->in_ep[i].queue_sof) { ++ pcd->in_ep[i].queue_sof = 0; ++ start_next_request(&pcd->in_ep[i]); ++ // break; ++ } ++ } ++ ++ return; ++} ++ ++/** ++ * This function initialized the PCD portion of the driver. ++ * ++ */ ++dwc_otg_pcd_t *dwc_otg_pcd_init(dwc_otg_device_t *otg_dev) ++{ ++ struct device *dev = &otg_dev->os_dep.platformdev->dev; ++ dwc_otg_core_if_t *core_if = otg_dev->core_if; ++ dwc_otg_pcd_t *pcd = NULL; ++ dwc_otg_dev_if_t *dev_if; ++ int i; ++ ++ /* ++ * Allocate PCD structure ++ */ ++ pcd = DWC_ALLOC(sizeof(dwc_otg_pcd_t)); ++ ++ if (pcd == NULL) { ++ return NULL; ++ } ++ ++#if (defined(DWC_LINUX) && defined(CONFIG_DEBUG_SPINLOCK)) ++ DWC_SPINLOCK_ALLOC_LINUX_DEBUG(pcd->lock); ++#else ++ pcd->lock = DWC_SPINLOCK_ALLOC(); ++#endif ++ DWC_DEBUGPL(DBG_HCDV, "Init of PCD %p given core_if %p\n", ++ pcd, core_if);//GRAYG ++ if (!pcd->lock) { ++ DWC_ERROR("Could not allocate lock for pcd"); ++ DWC_FREE(pcd); ++ return NULL; ++ } ++ /* Set core_if's lock pointer to hcd->lock */ ++ core_if->lock = pcd->lock; ++ pcd->core_if = core_if; ++ ++ dev_if = core_if->dev_if; ++ dev_if->isoc_ep = NULL; ++ ++ if (core_if->hwcfg4.b.ded_fifo_en) { ++ DWC_PRINTF("Dedicated Tx FIFOs mode\n"); ++ } else { ++ DWC_PRINTF("Shared Tx FIFO mode\n"); ++ } ++ ++ /* ++ * Initialized the Core for Device mode here if there is nod ADP support. ++ * Otherwise it will be done later in dwc_otg_adp_start routine. ++ */ ++ if (dwc_otg_is_device_mode(core_if) /*&& !core_if->adp_enable*/) { ++ dwc_otg_core_dev_init(core_if); ++ } ++ ++ /* ++ * Register the PCD Callbacks. ++ */ ++ dwc_otg_cil_register_pcd_callbacks(core_if, &pcd_callbacks, pcd); ++ ++ /* ++ * Initialize the DMA buffer for SETUP packets ++ */ ++ if (GET_CORE_IF(pcd)->dma_enable) { ++ pcd->setup_pkt = ++ DWC_DMA_ALLOC(dev, sizeof(*pcd->setup_pkt) * 5, ++ &pcd->setup_pkt_dma_handle); ++ if (pcd->setup_pkt == NULL) { ++ DWC_FREE(pcd); ++ return NULL; ++ } ++ ++ pcd->status_buf = ++ DWC_DMA_ALLOC(dev, sizeof(uint16_t), ++ &pcd->status_buf_dma_handle); ++ if (pcd->status_buf == NULL) { ++ DWC_DMA_FREE(dev, sizeof(*pcd->setup_pkt) * 5, ++ pcd->setup_pkt, pcd->setup_pkt_dma_handle); ++ DWC_FREE(pcd); ++ return NULL; ++ } ++ ++ if (GET_CORE_IF(pcd)->dma_desc_enable) { ++ dev_if->setup_desc_addr[0] = ++ dwc_otg_ep_alloc_desc_chain(dev, ++ &dev_if->dma_setup_desc_addr[0], 1); ++ dev_if->setup_desc_addr[1] = ++ dwc_otg_ep_alloc_desc_chain(dev, ++ &dev_if->dma_setup_desc_addr[1], 1); ++ dev_if->in_desc_addr = ++ dwc_otg_ep_alloc_desc_chain(dev, ++ &dev_if->dma_in_desc_addr, 1); ++ dev_if->out_desc_addr = ++ dwc_otg_ep_alloc_desc_chain(dev, ++ &dev_if->dma_out_desc_addr, 1); ++ pcd->data_terminated = 0; ++ ++ if (dev_if->setup_desc_addr[0] == 0 ++ || dev_if->setup_desc_addr[1] == 0 ++ || dev_if->in_desc_addr == 0 ++ || dev_if->out_desc_addr == 0) { ++ ++ if (dev_if->out_desc_addr) ++ dwc_otg_ep_free_desc_chain(dev, ++ dev_if->out_desc_addr, ++ dev_if->dma_out_desc_addr, 1); ++ if (dev_if->in_desc_addr) ++ dwc_otg_ep_free_desc_chain(dev, ++ dev_if->in_desc_addr, ++ dev_if->dma_in_desc_addr, 1); ++ if (dev_if->setup_desc_addr[1]) ++ dwc_otg_ep_free_desc_chain(dev, ++ dev_if->setup_desc_addr[1], ++ dev_if->dma_setup_desc_addr[1], 1); ++ if (dev_if->setup_desc_addr[0]) ++ dwc_otg_ep_free_desc_chain(dev, ++ dev_if->setup_desc_addr[0], ++ dev_if->dma_setup_desc_addr[0], 1); ++ ++ DWC_DMA_FREE(dev, sizeof(*pcd->setup_pkt) * 5, ++ pcd->setup_pkt, ++ pcd->setup_pkt_dma_handle); ++ DWC_DMA_FREE(dev, sizeof(*pcd->status_buf), ++ pcd->status_buf, ++ pcd->status_buf_dma_handle); ++ ++ DWC_FREE(pcd); ++ ++ return NULL; ++ } ++ } ++ } else { ++ pcd->setup_pkt = DWC_ALLOC(sizeof(*pcd->setup_pkt) * 5); ++ if (pcd->setup_pkt == NULL) { ++ DWC_FREE(pcd); ++ return NULL; ++ } ++ ++ pcd->status_buf = DWC_ALLOC(sizeof(uint16_t)); ++ if (pcd->status_buf == NULL) { ++ DWC_FREE(pcd->setup_pkt); ++ DWC_FREE(pcd); ++ return NULL; ++ } ++ } ++ ++ dwc_otg_pcd_reinit(pcd); ++ ++ /* Allocate the cfi object for the PCD */ ++#ifdef DWC_UTE_CFI ++ pcd->cfi = DWC_ALLOC(sizeof(cfiobject_t)); ++ if (NULL == pcd->cfi) ++ goto fail; ++ if (init_cfi(pcd->cfi)) { ++ CFI_INFO("%s: Failed to init the CFI object\n", __func__); ++ goto fail; ++ } ++#endif ++ ++ /* Initialize tasklets */ ++ pcd->start_xfer_tasklet = DWC_TASK_ALLOC("xfer_tasklet", ++ start_xfer_tasklet_func, pcd); ++ pcd->test_mode_tasklet = DWC_TASK_ALLOC("test_mode_tasklet", ++ do_test_mode, pcd); ++ ++ /* Initialize SRP timer */ ++ core_if->srp_timer = DWC_TIMER_ALLOC("SRP TIMER", srp_timeout, core_if); ++ ++ if (core_if->core_params->dev_out_nak) { ++ /** ++ * Initialize xfer timeout timer. Implemented for ++ * 2.93a feature "Device DDMA OUT NAK Enhancement" ++ */ ++ for(i = 0; i < MAX_EPS_CHANNELS; i++) { ++ pcd->core_if->ep_xfer_timer[i] = ++ DWC_TIMER_ALLOC("ep timer", ep_xfer_timeout, ++ &pcd->core_if->ep_xfer_info[i]); ++ } ++ } ++ ++ return pcd; ++#ifdef DWC_UTE_CFI ++fail: ++#endif ++ if (pcd->setup_pkt) ++ DWC_FREE(pcd->setup_pkt); ++ if (pcd->status_buf) ++ DWC_FREE(pcd->status_buf); ++#ifdef DWC_UTE_CFI ++ if (pcd->cfi) ++ DWC_FREE(pcd->cfi); ++#endif ++ if (pcd) ++ DWC_FREE(pcd); ++ return NULL; ++ ++} ++ ++/** ++ * Remove PCD specific data ++ */ ++void dwc_otg_pcd_remove(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_dev_if_t *dev_if = GET_CORE_IF(pcd)->dev_if; ++ struct device *dev = dwc_otg_pcd_to_dev(pcd); ++ int i; ++ ++ if (pcd->core_if->core_params->dev_out_nak) { ++ for (i = 0; i < MAX_EPS_CHANNELS; i++) { ++ DWC_TIMER_CANCEL(pcd->core_if->ep_xfer_timer[i]); ++ pcd->core_if->ep_xfer_info[i].state = 0; ++ } ++ } ++ ++ if (GET_CORE_IF(pcd)->dma_enable) { ++ DWC_DMA_FREE(dev, sizeof(*pcd->setup_pkt) * 5, pcd->setup_pkt, ++ pcd->setup_pkt_dma_handle); ++ DWC_DMA_FREE(dev, sizeof(uint16_t), pcd->status_buf, ++ pcd->status_buf_dma_handle); ++ if (GET_CORE_IF(pcd)->dma_desc_enable) { ++ dwc_otg_ep_free_desc_chain(dev, ++ dev_if->setup_desc_addr[0], ++ dev_if->dma_setup_desc_addr ++ [0], 1); ++ dwc_otg_ep_free_desc_chain(dev, ++ dev_if->setup_desc_addr[1], ++ dev_if->dma_setup_desc_addr ++ [1], 1); ++ dwc_otg_ep_free_desc_chain(dev, ++ dev_if->in_desc_addr, ++ dev_if->dma_in_desc_addr, 1); ++ dwc_otg_ep_free_desc_chain(dev, ++ dev_if->out_desc_addr, ++ dev_if->dma_out_desc_addr, ++ 1); ++ } ++ } else { ++ DWC_FREE(pcd->setup_pkt); ++ DWC_FREE(pcd->status_buf); ++ } ++ DWC_SPINLOCK_FREE(pcd->lock); ++ /* Set core_if's lock pointer to NULL */ ++ pcd->core_if->lock = NULL; ++ ++ DWC_TASK_FREE(pcd->start_xfer_tasklet); ++ DWC_TASK_FREE(pcd->test_mode_tasklet); ++ if (pcd->core_if->core_params->dev_out_nak) { ++ for (i = 0; i < MAX_EPS_CHANNELS; i++) { ++ if (pcd->core_if->ep_xfer_timer[i]) { ++ DWC_TIMER_FREE(pcd->core_if->ep_xfer_timer[i]); ++ } ++ } ++ } ++ ++/* Release the CFI object's dynamic memory */ ++#ifdef DWC_UTE_CFI ++ if (pcd->cfi->ops.release) { ++ pcd->cfi->ops.release(pcd->cfi); ++ } ++#endif ++ ++ DWC_FREE(pcd); ++} ++ ++/** ++ * Returns whether registered pcd is dual speed or not ++ */ ++uint32_t dwc_otg_pcd_is_dualspeed(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ ++ if ((core_if->core_params->speed == DWC_SPEED_PARAM_FULL) || ++ ((core_if->hwcfg2.b.hs_phy_type == 2) && ++ (core_if->hwcfg2.b.fs_phy_type == 1) && ++ (core_if->core_params->ulpi_fs_ls))) { ++ return 0; ++ } ++ ++ return 1; ++} ++ ++/** ++ * Returns whether registered pcd is OTG capable or not ++ */ ++uint32_t dwc_otg_pcd_is_otg(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ gusbcfg_data_t usbcfg = {.d32 = 0 }; ++ ++ usbcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->gusbcfg); ++ if (!usbcfg.b.srpcap || !usbcfg.b.hnpcap) { ++ return 0; ++ } ++ ++ return 1; ++} ++ ++/** ++ * This function assigns periodic Tx FIFO to an periodic EP ++ * in shared Tx FIFO mode ++ */ ++static uint32_t assign_tx_fifo(dwc_otg_core_if_t * core_if) ++{ ++ uint32_t TxMsk = 1; ++ int i; ++ ++ for (i = 0; i < core_if->hwcfg4.b.num_in_eps; ++i) { ++ if ((TxMsk & core_if->tx_msk) == 0) { ++ core_if->tx_msk |= TxMsk; ++ return i + 1; ++ } ++ TxMsk <<= 1; ++ } ++ return 0; ++} ++ ++/** ++ * This function assigns periodic Tx FIFO to an periodic EP ++ * in shared Tx FIFO mode ++ */ ++static uint32_t assign_perio_tx_fifo(dwc_otg_core_if_t * core_if) ++{ ++ uint32_t PerTxMsk = 1; ++ int i; ++ for (i = 0; i < core_if->hwcfg4.b.num_dev_perio_in_ep; ++i) { ++ if ((PerTxMsk & core_if->p_tx_msk) == 0) { ++ core_if->p_tx_msk |= PerTxMsk; ++ return i + 1; ++ } ++ PerTxMsk <<= 1; ++ } ++ return 0; ++} ++ ++/** ++ * This function releases periodic Tx FIFO ++ * in shared Tx FIFO mode ++ */ ++static void release_perio_tx_fifo(dwc_otg_core_if_t * core_if, ++ uint32_t fifo_num) ++{ ++ core_if->p_tx_msk = ++ (core_if->p_tx_msk & (1 << (fifo_num - 1))) ^ core_if->p_tx_msk; ++} ++ ++/** ++ * This function releases periodic Tx FIFO ++ * in shared Tx FIFO mode ++ */ ++static void release_tx_fifo(dwc_otg_core_if_t * core_if, uint32_t fifo_num) ++{ ++ core_if->tx_msk = ++ (core_if->tx_msk & (1 << (fifo_num - 1))) ^ core_if->tx_msk; ++} ++ ++/** ++ * This function is being called from gadget ++ * to enable PCD endpoint. ++ */ ++int dwc_otg_pcd_ep_enable(dwc_otg_pcd_t * pcd, ++ const uint8_t * ep_desc, void *usb_ep) ++{ ++ int num, dir; ++ dwc_otg_pcd_ep_t *ep = NULL; ++ const usb_endpoint_descriptor_t *desc; ++ dwc_irqflags_t flags; ++ fifosize_data_t dptxfsiz = {.d32 = 0 }; ++ gdfifocfg_data_t gdfifocfg = {.d32 = 0 }; ++ gdfifocfg_data_t gdfifocfgbase = {.d32 = 0 }; ++ int retval = 0; ++ int i, epcount; ++ struct device *dev = dwc_otg_pcd_to_dev(pcd); ++ ++ desc = (const usb_endpoint_descriptor_t *)ep_desc; ++ ++ if (!desc) { ++ pcd->ep0.priv = usb_ep; ++ ep = &pcd->ep0; ++ retval = -DWC_E_INVALID; ++ goto out; ++ } ++ ++ num = UE_GET_ADDR(desc->bEndpointAddress); ++ dir = UE_GET_DIR(desc->bEndpointAddress); ++ ++ if (!desc->wMaxPacketSize) { ++ DWC_WARN("bad maxpacketsize\n"); ++ retval = -DWC_E_INVALID; ++ goto out; ++ } ++ ++ if (dir == UE_DIR_IN) { ++ epcount = pcd->core_if->dev_if->num_in_eps; ++ for (i = 0; i < epcount; i++) { ++ if (num == pcd->in_ep[i].dwc_ep.num) { ++ ep = &pcd->in_ep[i]; ++ break; ++ } ++ } ++ } else { ++ epcount = pcd->core_if->dev_if->num_out_eps; ++ for (i = 0; i < epcount; i++) { ++ if (num == pcd->out_ep[i].dwc_ep.num) { ++ ep = &pcd->out_ep[i]; ++ break; ++ } ++ } ++ } ++ ++ if (!ep) { ++ DWC_WARN("bad address\n"); ++ retval = -DWC_E_INVALID; ++ goto out; ++ } ++ ++ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags); ++ ++ ep->desc = desc; ++ ep->priv = usb_ep; ++ ++ /* ++ * Activate the EP ++ */ ++ ep->stopped = 0; ++ ++ ep->dwc_ep.is_in = (dir == UE_DIR_IN); ++ ep->dwc_ep.maxpacket = UGETW(desc->wMaxPacketSize); ++ ++ ep->dwc_ep.type = desc->bmAttributes & UE_XFERTYPE; ++ ++ if (ep->dwc_ep.is_in) { ++ if (!GET_CORE_IF(pcd)->en_multiple_tx_fifo) { ++ ep->dwc_ep.tx_fifo_num = 0; ++ ++ if (ep->dwc_ep.type == UE_ISOCHRONOUS) { ++ /* ++ * if ISOC EP then assign a Periodic Tx FIFO. ++ */ ++ ep->dwc_ep.tx_fifo_num = ++ assign_perio_tx_fifo(GET_CORE_IF(pcd)); ++ } ++ } else { ++ /* ++ * if Dedicated FIFOs mode is on then assign a Tx FIFO. ++ */ ++ ep->dwc_ep.tx_fifo_num = ++ assign_tx_fifo(GET_CORE_IF(pcd)); ++ } ++ ++ /* Calculating EP info controller base address */ ++ if (ep->dwc_ep.tx_fifo_num ++ && GET_CORE_IF(pcd)->en_multiple_tx_fifo) { ++ gdfifocfg.d32 = ++ DWC_READ_REG32(&GET_CORE_IF(pcd)-> ++ core_global_regs->gdfifocfg); ++ gdfifocfgbase.d32 = gdfifocfg.d32 >> 16; ++ dptxfsiz.d32 = ++ (DWC_READ_REG32 ++ (&GET_CORE_IF(pcd)->core_global_regs-> ++ dtxfsiz[ep->dwc_ep.tx_fifo_num - 1]) >> 16); ++ gdfifocfg.b.epinfobase = ++ gdfifocfgbase.d32 + dptxfsiz.d32; ++ if (GET_CORE_IF(pcd)->snpsid <= OTG_CORE_REV_2_94a) { ++ DWC_WRITE_REG32(&GET_CORE_IF(pcd)-> ++ core_global_regs->gdfifocfg, ++ gdfifocfg.d32); ++ } ++ } ++ } ++ /* Set initial data PID. */ ++ if (ep->dwc_ep.type == UE_BULK) { ++ ep->dwc_ep.data_pid_start = 0; ++ } ++ ++ /* Alloc DMA Descriptors */ ++ if (GET_CORE_IF(pcd)->dma_desc_enable) { ++#ifndef DWC_UTE_PER_IO ++ if (ep->dwc_ep.type != UE_ISOCHRONOUS) { ++#endif ++ ep->dwc_ep.desc_addr = ++ dwc_otg_ep_alloc_desc_chain(dev, ++ &ep->dwc_ep.dma_desc_addr, ++ MAX_DMA_DESC_CNT); ++ if (!ep->dwc_ep.desc_addr) { ++ DWC_WARN("%s, can't allocate DMA descriptor\n", ++ __func__); ++ retval = -DWC_E_SHUTDOWN; ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ goto out; ++ } ++#ifndef DWC_UTE_PER_IO ++ } ++#endif ++ } ++ ++ DWC_DEBUGPL(DBG_PCD, "Activate %s: type=%d, mps=%d desc=%p\n", ++ (ep->dwc_ep.is_in ? "IN" : "OUT"), ++ ep->dwc_ep.type, ep->dwc_ep.maxpacket, ep->desc); ++#ifdef DWC_UTE_PER_IO ++ ep->dwc_ep.xiso_bInterval = 1 << (ep->desc->bInterval - 1); ++#endif ++ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) { ++ ep->dwc_ep.bInterval = 1 << (ep->desc->bInterval - 1); ++ ep->dwc_ep.frame_num = 0xFFFFFFFF; ++ } ++ ++ dwc_otg_ep_activate(GET_CORE_IF(pcd), &ep->dwc_ep); ++ ++#ifdef DWC_UTE_CFI ++ if (pcd->cfi->ops.ep_enable) { ++ pcd->cfi->ops.ep_enable(pcd->cfi, pcd, ep); ++ } ++#endif ++ ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ ++out: ++ return retval; ++} ++ ++/** ++ * This function is being called from gadget ++ * to disable PCD endpoint. ++ */ ++int dwc_otg_pcd_ep_disable(dwc_otg_pcd_t * pcd, void *ep_handle) ++{ ++ dwc_otg_pcd_ep_t *ep; ++ dwc_irqflags_t flags; ++ dwc_otg_dev_dma_desc_t *desc_addr; ++ dwc_dma_t dma_desc_addr; ++ gdfifocfg_data_t gdfifocfgbase = {.d32 = 0 }; ++ gdfifocfg_data_t gdfifocfg = {.d32 = 0 }; ++ fifosize_data_t dptxfsiz = {.d32 = 0 }; ++ struct device *dev = dwc_otg_pcd_to_dev(pcd); ++ ++ ep = get_ep_from_handle(pcd, ep_handle); ++ ++ if (!ep || !ep->desc) { ++ DWC_DEBUGPL(DBG_PCD, "bad ep address\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags); ++ ++ dwc_otg_request_nuke(ep); ++ ++ dwc_otg_ep_deactivate(GET_CORE_IF(pcd), &ep->dwc_ep); ++ if (pcd->core_if->core_params->dev_out_nak) { ++ DWC_TIMER_CANCEL(pcd->core_if->ep_xfer_timer[ep->dwc_ep.num]); ++ pcd->core_if->ep_xfer_info[ep->dwc_ep.num].state = 0; ++ } ++ ep->desc = NULL; ++ ep->stopped = 1; ++ ++ gdfifocfg.d32 = ++ DWC_READ_REG32(&GET_CORE_IF(pcd)->core_global_regs->gdfifocfg); ++ gdfifocfgbase.d32 = gdfifocfg.d32 >> 16; ++ ++ if (ep->dwc_ep.is_in) { ++ if (GET_CORE_IF(pcd)->en_multiple_tx_fifo) { ++ /* Flush the Tx FIFO */ ++ dwc_otg_flush_tx_fifo(GET_CORE_IF(pcd), ++ ep->dwc_ep.tx_fifo_num); ++ } ++ release_perio_tx_fifo(GET_CORE_IF(pcd), ep->dwc_ep.tx_fifo_num); ++ release_tx_fifo(GET_CORE_IF(pcd), ep->dwc_ep.tx_fifo_num); ++ if (GET_CORE_IF(pcd)->en_multiple_tx_fifo) { ++ /* Decreasing EPinfo Base Addr */ ++ dptxfsiz.d32 = ++ (DWC_READ_REG32 ++ (&GET_CORE_IF(pcd)-> ++ core_global_regs->dtxfsiz[ep->dwc_ep.tx_fifo_num-1]) >> 16); ++ gdfifocfg.b.epinfobase = gdfifocfgbase.d32 - dptxfsiz.d32; ++ if (GET_CORE_IF(pcd)->snpsid <= OTG_CORE_REV_2_94a) { ++ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gdfifocfg, ++ gdfifocfg.d32); ++ } ++ } ++ } ++ ++ /* Free DMA Descriptors */ ++ if (GET_CORE_IF(pcd)->dma_desc_enable) { ++ if (ep->dwc_ep.type != UE_ISOCHRONOUS) { ++ desc_addr = ep->dwc_ep.desc_addr; ++ dma_desc_addr = ep->dwc_ep.dma_desc_addr; ++ ++ /* Cannot call dma_free_coherent() with IRQs disabled */ ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ dwc_otg_ep_free_desc_chain(dev, desc_addr, dma_desc_addr, ++ MAX_DMA_DESC_CNT); ++ ++ goto out_unlocked; ++ } ++ } ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ ++out_unlocked: ++ DWC_DEBUGPL(DBG_PCD, "%d %s disabled\n", ep->dwc_ep.num, ++ ep->dwc_ep.is_in ? "IN" : "OUT"); ++ return 0; ++ ++} ++ ++/******************************************************************************/ ++#ifdef DWC_UTE_PER_IO ++ ++/** ++ * Free the request and its extended parts ++ * ++ */ ++void dwc_pcd_xiso_ereq_free(dwc_otg_pcd_ep_t * ep, dwc_otg_pcd_request_t * req) ++{ ++ DWC_FREE(req->ext_req.per_io_frame_descs); ++ DWC_FREE(req); ++} ++ ++/** ++ * Start the next request in the endpoint's queue. ++ * ++ */ ++int dwc_otg_pcd_xiso_start_next_request(dwc_otg_pcd_t * pcd, ++ dwc_otg_pcd_ep_t * ep) ++{ ++ int i; ++ dwc_otg_pcd_request_t *req = NULL; ++ dwc_ep_t *dwcep = NULL; ++ struct dwc_iso_xreq_port *ereq = NULL; ++ struct dwc_iso_pkt_desc_port *ddesc_iso; ++ uint16_t nat; ++ depctl_data_t diepctl; ++ ++ dwcep = &ep->dwc_ep; ++ ++ if (dwcep->xiso_active_xfers > 0) { ++#if 0 //Disable this to decrease s/w overhead that is crucial for Isoc transfers ++ DWC_WARN("There are currently active transfers for EP%d \ ++ (active=%d; queued=%d)", dwcep->num, dwcep->xiso_active_xfers, ++ dwcep->xiso_queued_xfers); ++#endif ++ return 0; ++ } ++ ++ nat = UGETW(ep->desc->wMaxPacketSize); ++ nat = (nat >> 11) & 0x03; ++ ++ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) { ++ req = DWC_CIRCLEQ_FIRST(&ep->queue); ++ ereq = &req->ext_req; ++ ep->stopped = 0; ++ ++ /* Get the frame number */ ++ dwcep->xiso_frame_num = ++ dwc_otg_get_frame_number(GET_CORE_IF(pcd)); ++ DWC_DEBUG("FRM_NUM=%d", dwcep->xiso_frame_num); ++ ++ ddesc_iso = ereq->per_io_frame_descs; ++ ++ if (dwcep->is_in) { ++ /* Setup DMA Descriptor chain for IN Isoc request */ ++ for (i = 0; i < ereq->pio_pkt_count; i++) { ++ //if ((i % (nat + 1)) == 0) ++ if ( i > 0 ) ++ dwcep->xiso_frame_num = ++ (dwcep->xiso_bInterval + ++ dwcep->xiso_frame_num) & 0x3FFF; ++ dwcep->desc_addr[i].buf = ++ req->dma + ddesc_iso[i].offset; ++ dwcep->desc_addr[i].status.b_iso_in.txbytes = ++ ddesc_iso[i].length; ++ dwcep->desc_addr[i].status.b_iso_in.framenum = ++ dwcep->xiso_frame_num; ++ dwcep->desc_addr[i].status.b_iso_in.bs = ++ BS_HOST_READY; ++ dwcep->desc_addr[i].status.b_iso_in.txsts = 0; ++ dwcep->desc_addr[i].status.b_iso_in.sp = ++ (ddesc_iso[i].length % ++ dwcep->maxpacket) ? 1 : 0; ++ dwcep->desc_addr[i].status.b_iso_in.ioc = 0; ++ dwcep->desc_addr[i].status.b_iso_in.pid = nat + 1; ++ dwcep->desc_addr[i].status.b_iso_in.l = 0; ++ ++ /* Process the last descriptor */ ++ if (i == ereq->pio_pkt_count - 1) { ++ dwcep->desc_addr[i].status.b_iso_in.ioc = 1; ++ dwcep->desc_addr[i].status.b_iso_in.l = 1; ++ } ++ } ++ ++ /* Setup and start the transfer for this endpoint */ ++ dwcep->xiso_active_xfers++; ++ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->dev_if-> ++ in_ep_regs[dwcep->num]->diepdma, ++ dwcep->dma_desc_addr); ++ diepctl.d32 = 0; ++ diepctl.b.epena = 1; ++ diepctl.b.cnak = 1; ++ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->dev_if-> ++ in_ep_regs[dwcep->num]->diepctl, 0, ++ diepctl.d32); ++ } else { ++ /* Setup DMA Descriptor chain for OUT Isoc request */ ++ for (i = 0; i < ereq->pio_pkt_count; i++) { ++ //if ((i % (nat + 1)) == 0) ++ dwcep->xiso_frame_num = (dwcep->xiso_bInterval + ++ dwcep->xiso_frame_num) & 0x3FFF; ++ dwcep->desc_addr[i].buf = ++ req->dma + ddesc_iso[i].offset; ++ dwcep->desc_addr[i].status.b_iso_out.rxbytes = ++ ddesc_iso[i].length; ++ dwcep->desc_addr[i].status.b_iso_out.framenum = ++ dwcep->xiso_frame_num; ++ dwcep->desc_addr[i].status.b_iso_out.bs = ++ BS_HOST_READY; ++ dwcep->desc_addr[i].status.b_iso_out.rxsts = 0; ++ dwcep->desc_addr[i].status.b_iso_out.sp = ++ (ddesc_iso[i].length % ++ dwcep->maxpacket) ? 1 : 0; ++ dwcep->desc_addr[i].status.b_iso_out.ioc = 0; ++ dwcep->desc_addr[i].status.b_iso_out.pid = nat + 1; ++ dwcep->desc_addr[i].status.b_iso_out.l = 0; ++ ++ /* Process the last descriptor */ ++ if (i == ereq->pio_pkt_count - 1) { ++ dwcep->desc_addr[i].status.b_iso_out.ioc = 1; ++ dwcep->desc_addr[i].status.b_iso_out.l = 1; ++ } ++ } ++ ++ /* Setup and start the transfer for this endpoint */ ++ dwcep->xiso_active_xfers++; ++ DWC_WRITE_REG32(&GET_CORE_IF(pcd)-> ++ dev_if->out_ep_regs[dwcep->num]-> ++ doepdma, dwcep->dma_desc_addr); ++ diepctl.d32 = 0; ++ diepctl.b.epena = 1; ++ diepctl.b.cnak = 1; ++ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)-> ++ dev_if->out_ep_regs[dwcep->num]-> ++ doepctl, 0, diepctl.d32); ++ } ++ ++ } else { ++ ep->stopped = 1; ++ } ++ ++ return 0; ++} ++ ++/** ++ * - Remove the request from the queue ++ */ ++void complete_xiso_ep(dwc_otg_pcd_ep_t * ep) ++{ ++ dwc_otg_pcd_request_t *req = NULL; ++ struct dwc_iso_xreq_port *ereq = NULL; ++ struct dwc_iso_pkt_desc_port *ddesc_iso = NULL; ++ dwc_ep_t *dwcep = NULL; ++ int i; ++ ++ //DWC_DEBUG(); ++ dwcep = &ep->dwc_ep; ++ ++ /* Get the first pending request from the queue */ ++ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) { ++ req = DWC_CIRCLEQ_FIRST(&ep->queue); ++ if (!req) { ++ DWC_PRINTF("complete_ep 0x%p, req = NULL!\n", ep); ++ return; ++ } ++ dwcep->xiso_active_xfers--; ++ dwcep->xiso_queued_xfers--; ++ /* Remove this request from the queue */ ++ DWC_CIRCLEQ_REMOVE_INIT(&ep->queue, req, queue_entry); ++ } else { ++ DWC_PRINTF("complete_ep 0x%p, ep->queue empty!\n", ep); ++ return; ++ } ++ ++ ep->stopped = 1; ++ ereq = &req->ext_req; ++ ddesc_iso = ereq->per_io_frame_descs; ++ ++ if (dwcep->xiso_active_xfers < 0) { ++ DWC_WARN("EP#%d (xiso_active_xfers=%d)", dwcep->num, ++ dwcep->xiso_active_xfers); ++ } ++ ++ /* Fill the Isoc descs of portable extended req from dma descriptors */ ++ for (i = 0; i < ereq->pio_pkt_count; i++) { ++ if (dwcep->is_in) { /* IN endpoints */ ++ ddesc_iso[i].actual_length = ddesc_iso[i].length - ++ dwcep->desc_addr[i].status.b_iso_in.txbytes; ++ ddesc_iso[i].status = ++ dwcep->desc_addr[i].status.b_iso_in.txsts; ++ } else { /* OUT endpoints */ ++ ddesc_iso[i].actual_length = ddesc_iso[i].length - ++ dwcep->desc_addr[i].status.b_iso_out.rxbytes; ++ ddesc_iso[i].status = ++ dwcep->desc_addr[i].status.b_iso_out.rxsts; ++ } ++ } ++ ++ DWC_SPINUNLOCK(ep->pcd->lock); ++ ++ /* Call the completion function in the non-portable logic */ ++ ep->pcd->fops->xisoc_complete(ep->pcd, ep->priv, req->priv, 0, ++ &req->ext_req); ++ ++ DWC_SPINLOCK(ep->pcd->lock); ++ ++ /* Free the request - specific freeing needed for extended request object */ ++ dwc_pcd_xiso_ereq_free(ep, req); ++ ++ /* Start the next request */ ++ dwc_otg_pcd_xiso_start_next_request(ep->pcd, ep); ++ ++ return; ++} ++ ++/** ++ * Create and initialize the Isoc pkt descriptors of the extended request. ++ * ++ */ ++static int dwc_otg_pcd_xiso_create_pkt_descs(dwc_otg_pcd_request_t * req, ++ void *ereq_nonport, ++ int atomic_alloc) ++{ ++ struct dwc_iso_xreq_port *ereq = NULL; ++ struct dwc_iso_xreq_port *req_mapped = NULL; ++ struct dwc_iso_pkt_desc_port *ipds = NULL; /* To be created in this function */ ++ uint32_t pkt_count; ++ int i; ++ ++ ereq = &req->ext_req; ++ req_mapped = (struct dwc_iso_xreq_port *)ereq_nonport; ++ pkt_count = req_mapped->pio_pkt_count; ++ ++ /* Create the isoc descs */ ++ if (atomic_alloc) { ++ ipds = DWC_ALLOC_ATOMIC(sizeof(*ipds) * pkt_count); ++ } else { ++ ipds = DWC_ALLOC(sizeof(*ipds) * pkt_count); ++ } ++ ++ if (!ipds) { ++ DWC_ERROR("Failed to allocate isoc descriptors"); ++ return -DWC_E_NO_MEMORY; ++ } ++ ++ /* Initialize the extended request fields */ ++ ereq->per_io_frame_descs = ipds; ++ ereq->error_count = 0; ++ ereq->pio_alloc_pkt_count = pkt_count; ++ ereq->pio_pkt_count = pkt_count; ++ ereq->tr_sub_flags = req_mapped->tr_sub_flags; ++ ++ /* Init the Isoc descriptors */ ++ for (i = 0; i < pkt_count; i++) { ++ ipds[i].length = req_mapped->per_io_frame_descs[i].length; ++ ipds[i].offset = req_mapped->per_io_frame_descs[i].offset; ++ ipds[i].status = req_mapped->per_io_frame_descs[i].status; /* 0 */ ++ ipds[i].actual_length = ++ req_mapped->per_io_frame_descs[i].actual_length; ++ } ++ ++ return 0; ++} ++ ++static void prn_ext_request(struct dwc_iso_xreq_port *ereq) ++{ ++ struct dwc_iso_pkt_desc_port *xfd = NULL; ++ int i; ++ ++ DWC_DEBUG("per_io_frame_descs=%p", ereq->per_io_frame_descs); ++ DWC_DEBUG("tr_sub_flags=%d", ereq->tr_sub_flags); ++ DWC_DEBUG("error_count=%d", ereq->error_count); ++ DWC_DEBUG("pio_alloc_pkt_count=%d", ereq->pio_alloc_pkt_count); ++ DWC_DEBUG("pio_pkt_count=%d", ereq->pio_pkt_count); ++ DWC_DEBUG("res=%d", ereq->res); ++ ++ for (i = 0; i < ereq->pio_pkt_count; i++) { ++ xfd = &ereq->per_io_frame_descs[0]; ++ DWC_DEBUG("FD #%d", i); ++ ++ DWC_DEBUG("xfd->actual_length=%d", xfd->actual_length); ++ DWC_DEBUG("xfd->length=%d", xfd->length); ++ DWC_DEBUG("xfd->offset=%d", xfd->offset); ++ DWC_DEBUG("xfd->status=%d", xfd->status); ++ } ++} ++ ++/** ++ * ++ */ ++int dwc_otg_pcd_xiso_ep_queue(dwc_otg_pcd_t * pcd, void *ep_handle, ++ uint8_t * buf, dwc_dma_t dma_buf, uint32_t buflen, ++ int zero, void *req_handle, int atomic_alloc, ++ void *ereq_nonport) ++{ ++ dwc_otg_pcd_request_t *req = NULL; ++ dwc_otg_pcd_ep_t *ep; ++ dwc_irqflags_t flags; ++ int res; ++ ++ ep = get_ep_from_handle(pcd, ep_handle); ++ if (!ep) { ++ DWC_WARN("bad ep\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ /* We support this extension only for DDMA mode */ ++ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) ++ if (!GET_CORE_IF(pcd)->dma_desc_enable) ++ return -DWC_E_INVALID; ++ ++ /* Create a dwc_otg_pcd_request_t object */ ++ if (atomic_alloc) { ++ req = DWC_ALLOC_ATOMIC(sizeof(*req)); ++ } else { ++ req = DWC_ALLOC(sizeof(*req)); ++ } ++ ++ if (!req) { ++ return -DWC_E_NO_MEMORY; ++ } ++ ++ /* Create the Isoc descs for this request which shall be the exact match ++ * of the structure sent to us from the non-portable logic */ ++ res = ++ dwc_otg_pcd_xiso_create_pkt_descs(req, ereq_nonport, atomic_alloc); ++ if (res) { ++ DWC_WARN("Failed to init the Isoc descriptors"); ++ DWC_FREE(req); ++ return res; ++ } ++ ++ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags); ++ ++ DWC_CIRCLEQ_INIT_ENTRY(req, queue_entry); ++ req->buf = buf; ++ req->dma = dma_buf; ++ req->length = buflen; ++ req->sent_zlp = zero; ++ req->priv = req_handle; ++ ++ //DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags); ++ ep->dwc_ep.dma_addr = dma_buf; ++ ep->dwc_ep.start_xfer_buff = buf; ++ ep->dwc_ep.xfer_buff = buf; ++ ep->dwc_ep.xfer_len = 0; ++ ep->dwc_ep.xfer_count = 0; ++ ep->dwc_ep.sent_zlp = 0; ++ ep->dwc_ep.total_len = buflen; ++ ++ /* Add this request to the tail */ ++ DWC_CIRCLEQ_INSERT_TAIL(&ep->queue, req, queue_entry); ++ ep->dwc_ep.xiso_queued_xfers++; ++ ++//DWC_DEBUG("CP_0"); ++//DWC_DEBUG("req->ext_req.tr_sub_flags=%d", req->ext_req.tr_sub_flags); ++//prn_ext_request((struct dwc_iso_xreq_port *) ereq_nonport); ++//prn_ext_request(&req->ext_req); ++ ++ //DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ ++ /* If the req->status == ASAP then check if there is any active transfer ++ * for this endpoint. If no active transfers, then get the first entry ++ * from the queue and start that transfer ++ */ ++ if (req->ext_req.tr_sub_flags == DWC_EREQ_TF_ASAP) { ++ res = dwc_otg_pcd_xiso_start_next_request(pcd, ep); ++ if (res) { ++ DWC_WARN("Failed to start the next Isoc transfer"); ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ DWC_FREE(req); ++ return res; ++ } ++ } ++ ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ return 0; ++} ++ ++#endif ++/* END ifdef DWC_UTE_PER_IO ***************************************************/ ++int dwc_otg_pcd_ep_queue(dwc_otg_pcd_t * pcd, void *ep_handle, ++ uint8_t * buf, dwc_dma_t dma_buf, uint32_t buflen, ++ int zero, void *req_handle, int atomic_alloc) ++{ ++ struct device *dev = dwc_otg_pcd_to_dev(pcd); ++ dwc_irqflags_t flags; ++ dwc_otg_pcd_request_t *req; ++ dwc_otg_pcd_ep_t *ep; ++ uint32_t max_transfer; ++ ++ ep = get_ep_from_handle(pcd, ep_handle); ++ if (!ep || (!ep->desc && ep->dwc_ep.num != 0)) { ++ DWC_WARN("bad ep\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ if (atomic_alloc) { ++ req = DWC_ALLOC_ATOMIC(sizeof(*req)); ++ } else { ++ req = DWC_ALLOC(sizeof(*req)); ++ } ++ ++ if (!req) { ++ return -DWC_E_NO_MEMORY; ++ } ++ DWC_CIRCLEQ_INIT_ENTRY(req, queue_entry); ++ if (!GET_CORE_IF(pcd)->core_params->opt) { ++ if (ep->dwc_ep.num != 0) { ++ DWC_ERROR("queue req %p, len %d buf %p\n", ++ req_handle, buflen, buf); ++ } ++ } ++ ++ req->buf = buf; ++ req->dma = dma_buf; ++ req->length = buflen; ++ req->sent_zlp = zero; ++ req->priv = req_handle; ++ req->dw_align_buf = NULL; ++ if ((dma_buf & 0x3) && GET_CORE_IF(pcd)->dma_enable ++ && !GET_CORE_IF(pcd)->dma_desc_enable) ++ req->dw_align_buf = DWC_DMA_ALLOC(dev, buflen, ++ &req->dw_align_buf_dma); ++ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags); ++ ++ /* ++ * After adding request to the queue for IN ISOC wait for In Token Received ++ * when TX FIFO is empty interrupt and for OUT ISOC wait for OUT Token ++ * Received when EP is disabled interrupt to obtain starting microframe ++ * (odd/even) start transfer ++ */ ++ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) { ++ if (req != 0) { ++ depctl_data_t depctl = {.d32 = ++ DWC_READ_REG32(&pcd->core_if->dev_if-> ++ in_ep_regs[ep->dwc_ep.num]-> ++ diepctl) }; ++ ++pcd->request_pending; ++ ++ DWC_CIRCLEQ_INSERT_TAIL(&ep->queue, req, queue_entry); ++ if (ep->dwc_ep.is_in) { ++ depctl.b.cnak = 1; ++ DWC_WRITE_REG32(&pcd->core_if->dev_if-> ++ in_ep_regs[ep->dwc_ep.num]-> ++ diepctl, depctl.d32); ++ } ++ ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ } ++ return 0; ++ } ++ ++ /* ++ * For EP0 IN without premature status, zlp is required? ++ */ ++ if (ep->dwc_ep.num == 0 && ep->dwc_ep.is_in) { ++ DWC_DEBUGPL(DBG_PCDV, "%d-OUT ZLP\n", ep->dwc_ep.num); ++ //_req->zero = 1; ++ } ++ ++ /* Start the transfer */ ++ if (DWC_CIRCLEQ_EMPTY(&ep->queue) && !ep->stopped) { ++ /* EP0 Transfer? */ ++ if (ep->dwc_ep.num == 0) { ++ switch (pcd->ep0state) { ++ case EP0_IN_DATA_PHASE: ++ DWC_DEBUGPL(DBG_PCD, ++ "%s ep0: EP0_IN_DATA_PHASE\n", ++ __func__); ++ break; ++ ++ case EP0_OUT_DATA_PHASE: ++ DWC_DEBUGPL(DBG_PCD, ++ "%s ep0: EP0_OUT_DATA_PHASE\n", ++ __func__); ++ if (pcd->request_config) { ++ /* Complete STATUS PHASE */ ++ ep->dwc_ep.is_in = 1; ++ pcd->ep0state = EP0_IN_STATUS_PHASE; ++ } ++ break; ++ ++ case EP0_IN_STATUS_PHASE: ++ DWC_DEBUGPL(DBG_PCD, ++ "%s ep0: EP0_IN_STATUS_PHASE\n", ++ __func__); ++ break; ++ ++ default: ++ DWC_DEBUGPL(DBG_ANY, "ep0: odd state %d\n", ++ pcd->ep0state); ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ return -DWC_E_SHUTDOWN; ++ } ++ ++ ep->dwc_ep.dma_addr = dma_buf; ++ ep->dwc_ep.start_xfer_buff = buf; ++ ep->dwc_ep.xfer_buff = buf; ++ ep->dwc_ep.xfer_len = buflen; ++ ep->dwc_ep.xfer_count = 0; ++ ep->dwc_ep.sent_zlp = 0; ++ ep->dwc_ep.total_len = ep->dwc_ep.xfer_len; ++ ++ if (zero) { ++ if ((ep->dwc_ep.xfer_len % ++ ep->dwc_ep.maxpacket == 0) ++ && (ep->dwc_ep.xfer_len != 0)) { ++ ep->dwc_ep.sent_zlp = 1; ++ } ++ ++ } ++ ++ dwc_otg_ep0_start_transfer(GET_CORE_IF(pcd), ++ &ep->dwc_ep); ++ } // non-ep0 endpoints ++ else { ++#ifdef DWC_UTE_CFI ++ if (ep->dwc_ep.buff_mode != BM_STANDARD) { ++ /* store the request length */ ++ ep->dwc_ep.cfi_req_len = buflen; ++ pcd->cfi->ops.build_descriptors(pcd->cfi, pcd, ++ ep, req); ++ } else { ++#endif ++ max_transfer = ++ GET_CORE_IF(ep->pcd)->core_params-> ++ max_transfer_size; ++ ++ /* Setup and start the Transfer */ ++ if (req->dw_align_buf){ ++ if (ep->dwc_ep.is_in) ++ dwc_memcpy(req->dw_align_buf, ++ buf, buflen); ++ ep->dwc_ep.dma_addr = ++ req->dw_align_buf_dma; ++ ep->dwc_ep.start_xfer_buff = ++ req->dw_align_buf; ++ ep->dwc_ep.xfer_buff = ++ req->dw_align_buf; ++ } else { ++ ep->dwc_ep.dma_addr = dma_buf; ++ ep->dwc_ep.start_xfer_buff = buf; ++ ep->dwc_ep.xfer_buff = buf; ++ } ++ ep->dwc_ep.xfer_len = 0; ++ ep->dwc_ep.xfer_count = 0; ++ ep->dwc_ep.sent_zlp = 0; ++ ep->dwc_ep.total_len = buflen; ++ ++ ep->dwc_ep.maxxfer = max_transfer; ++ if (GET_CORE_IF(pcd)->dma_desc_enable) { ++ uint32_t out_max_xfer = ++ DDMA_MAX_TRANSFER_SIZE - ++ (DDMA_MAX_TRANSFER_SIZE % 4); ++ if (ep->dwc_ep.is_in) { ++ if (ep->dwc_ep.maxxfer > ++ DDMA_MAX_TRANSFER_SIZE) { ++ ep->dwc_ep.maxxfer = ++ DDMA_MAX_TRANSFER_SIZE; ++ } ++ } else { ++ if (ep->dwc_ep.maxxfer > ++ out_max_xfer) { ++ ep->dwc_ep.maxxfer = ++ out_max_xfer; ++ } ++ } ++ } ++ if (ep->dwc_ep.maxxfer < ep->dwc_ep.total_len) { ++ ep->dwc_ep.maxxfer -= ++ (ep->dwc_ep.maxxfer % ++ ep->dwc_ep.maxpacket); ++ } ++ ++ if (zero) { ++ if ((ep->dwc_ep.total_len % ++ ep->dwc_ep.maxpacket == 0) ++ && (ep->dwc_ep.total_len != 0)) { ++ ep->dwc_ep.sent_zlp = 1; ++ } ++ } ++#ifdef DWC_UTE_CFI ++ } ++#endif ++ dwc_otg_ep_start_transfer(GET_CORE_IF(pcd), ++ &ep->dwc_ep); ++ } ++ } ++ ++ if (req != 0) { ++ ++pcd->request_pending; ++ DWC_CIRCLEQ_INSERT_TAIL(&ep->queue, req, queue_entry); ++ if (ep->dwc_ep.is_in && ep->stopped ++ && !(GET_CORE_IF(pcd)->dma_enable)) { ++ /** @todo NGS Create a function for this. */ ++ diepmsk_data_t diepmsk = {.d32 = 0 }; ++ diepmsk.b.intktxfemp = 1; ++ if (GET_CORE_IF(pcd)->multiproc_int_enable) { ++ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)-> ++ dev_if->dev_global_regs->diepeachintmsk ++ [ep->dwc_ep.num], 0, ++ diepmsk.d32); ++ } else { ++ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)-> ++ dev_if->dev_global_regs-> ++ diepmsk, 0, diepmsk.d32); ++ } ++ ++ } ++ } ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ ++ return 0; ++} ++ ++int dwc_otg_pcd_ep_dequeue(dwc_otg_pcd_t * pcd, void *ep_handle, ++ void *req_handle) ++{ ++ dwc_irqflags_t flags; ++ dwc_otg_pcd_request_t *req; ++ dwc_otg_pcd_ep_t *ep; ++ ++ ep = get_ep_from_handle(pcd, ep_handle); ++ if (!ep || (!ep->desc && ep->dwc_ep.num != 0)) { ++ DWC_WARN("bad argument\n"); ++ return -DWC_E_INVALID; ++ } ++ ++ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags); ++ ++ /* make sure it's actually queued on this endpoint */ ++ DWC_CIRCLEQ_FOREACH(req, &ep->queue, queue_entry) { ++ if (req->priv == (void *)req_handle) { ++ break; ++ } ++ } ++ ++ if (req->priv != (void *)req_handle) { ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ return -DWC_E_INVALID; ++ } ++ ++ if (!DWC_CIRCLEQ_EMPTY_ENTRY(req, queue_entry)) { ++ dwc_otg_request_done(ep, req, -DWC_E_RESTART); ++ } else { ++ req = NULL; ++ } ++ ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ ++ return req ? 0 : -DWC_E_SHUTDOWN; ++ ++} ++ ++/** ++ * dwc_otg_pcd_ep_wedge - sets the halt feature and ignores clear requests ++ * ++ * Use this to stall an endpoint and ignore CLEAR_FEATURE(HALT_ENDPOINT) ++ * requests. If the gadget driver clears the halt status, it will ++ * automatically unwedge the endpoint. ++ * ++ * Returns zero on success, else negative DWC error code. ++ */ ++int dwc_otg_pcd_ep_wedge(dwc_otg_pcd_t * pcd, void *ep_handle) ++{ ++ dwc_otg_pcd_ep_t *ep; ++ dwc_irqflags_t flags; ++ int retval = 0; ++ ++ ep = get_ep_from_handle(pcd, ep_handle); ++ ++ if ((!ep->desc && ep != &pcd->ep0) || ++ (ep->desc && (ep->desc->bmAttributes == UE_ISOCHRONOUS))) { ++ DWC_WARN("%s, bad ep\n", __func__); ++ return -DWC_E_INVALID; ++ } ++ ++ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags); ++ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) { ++ DWC_WARN("%d %s XFer In process\n", ep->dwc_ep.num, ++ ep->dwc_ep.is_in ? "IN" : "OUT"); ++ retval = -DWC_E_AGAIN; ++ } else { ++ /* This code needs to be reviewed */ ++ if (ep->dwc_ep.is_in == 1 && GET_CORE_IF(pcd)->dma_desc_enable) { ++ dtxfsts_data_t txstatus; ++ fifosize_data_t txfifosize; ++ ++ txfifosize.d32 = ++ DWC_READ_REG32(&GET_CORE_IF(pcd)-> ++ core_global_regs->dtxfsiz[ep->dwc_ep. ++ tx_fifo_num]); ++ txstatus.d32 = ++ DWC_READ_REG32(&GET_CORE_IF(pcd)-> ++ dev_if->in_ep_regs[ep->dwc_ep.num]-> ++ dtxfsts); ++ ++ if (txstatus.b.txfspcavail < txfifosize.b.depth) { ++ DWC_WARN("%s() Data In Tx Fifo\n", __func__); ++ retval = -DWC_E_AGAIN; ++ } else { ++ if (ep->dwc_ep.num == 0) { ++ pcd->ep0state = EP0_STALL; ++ } ++ ++ ep->stopped = 1; ++ dwc_otg_ep_set_stall(GET_CORE_IF(pcd), ++ &ep->dwc_ep); ++ } ++ } else { ++ if (ep->dwc_ep.num == 0) { ++ pcd->ep0state = EP0_STALL; ++ } ++ ++ ep->stopped = 1; ++ dwc_otg_ep_set_stall(GET_CORE_IF(pcd), &ep->dwc_ep); ++ } ++ } ++ ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ ++ return retval; ++} ++ ++int dwc_otg_pcd_ep_halt(dwc_otg_pcd_t * pcd, void *ep_handle, int value) ++{ ++ dwc_otg_pcd_ep_t *ep; ++ dwc_irqflags_t flags; ++ int retval = 0; ++ ++ ep = get_ep_from_handle(pcd, ep_handle); ++ ++ if (!ep || (!ep->desc && ep != &pcd->ep0) || ++ (ep->desc && (ep->desc->bmAttributes == UE_ISOCHRONOUS))) { ++ DWC_WARN("%s, bad ep\n", __func__); ++ return -DWC_E_INVALID; ++ } ++ ++ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags); ++ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) { ++ DWC_WARN("%d %s XFer In process\n", ep->dwc_ep.num, ++ ep->dwc_ep.is_in ? "IN" : "OUT"); ++ retval = -DWC_E_AGAIN; ++ } else if (value == 0) { ++ dwc_otg_ep_clear_stall(GET_CORE_IF(pcd), &ep->dwc_ep); ++ } else if (value == 1) { ++ if (ep->dwc_ep.is_in == 1 && GET_CORE_IF(pcd)->dma_desc_enable) { ++ dtxfsts_data_t txstatus; ++ fifosize_data_t txfifosize; ++ ++ txfifosize.d32 = ++ DWC_READ_REG32(&GET_CORE_IF(pcd)->core_global_regs-> ++ dtxfsiz[ep->dwc_ep.tx_fifo_num]); ++ txstatus.d32 = ++ DWC_READ_REG32(&GET_CORE_IF(pcd)->dev_if-> ++ in_ep_regs[ep->dwc_ep.num]->dtxfsts); ++ ++ if (txstatus.b.txfspcavail < txfifosize.b.depth) { ++ DWC_WARN("%s() Data In Tx Fifo\n", __func__); ++ retval = -DWC_E_AGAIN; ++ } else { ++ if (ep->dwc_ep.num == 0) { ++ pcd->ep0state = EP0_STALL; ++ } ++ ++ ep->stopped = 1; ++ dwc_otg_ep_set_stall(GET_CORE_IF(pcd), ++ &ep->dwc_ep); ++ } ++ } else { ++ if (ep->dwc_ep.num == 0) { ++ pcd->ep0state = EP0_STALL; ++ } ++ ++ ep->stopped = 1; ++ dwc_otg_ep_set_stall(GET_CORE_IF(pcd), &ep->dwc_ep); ++ } ++ } else if (value == 2) { ++ ep->dwc_ep.stall_clear_flag = 0; ++ } else if (value == 3) { ++ ep->dwc_ep.stall_clear_flag = 1; ++ } ++ ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ ++ return retval; ++} ++ ++/** ++ * This function initiates remote wakeup of the host from suspend state. ++ */ ++void dwc_otg_pcd_rem_wkup_from_suspend(dwc_otg_pcd_t * pcd, int set) ++{ ++ dctl_data_t dctl = { 0 }; ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dsts_data_t dsts; ++ ++ dsts.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts); ++ if (!dsts.b.suspsts) { ++ DWC_WARN("Remote wakeup while is not in suspend state\n"); ++ } ++ /* Check if DEVICE_REMOTE_WAKEUP feature enabled */ ++ if (pcd->remote_wakeup_enable) { ++ if (set) { ++ ++ if (core_if->adp_enable) { ++ gpwrdn_data_t gpwrdn; ++ ++ dwc_otg_adp_probe_stop(core_if); ++ ++ /* Mask SRP detected interrupt from Power Down Logic */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.srp_det_msk = 1; ++ DWC_MODIFY_REG32(&core_if-> ++ core_global_regs->gpwrdn, ++ gpwrdn.d32, 0); ++ ++ /* Disable Power Down Logic */ ++ gpwrdn.d32 = 0; ++ gpwrdn.b.pmuactv = 1; ++ DWC_MODIFY_REG32(&core_if-> ++ core_global_regs->gpwrdn, ++ gpwrdn.d32, 0); ++ ++ /* ++ * Initialize the Core for Device mode. ++ */ ++ core_if->op_state = B_PERIPHERAL; ++ dwc_otg_core_init(core_if); ++ dwc_otg_enable_global_interrupts(core_if); ++ cil_pcd_start(core_if); ++ ++ dwc_otg_initiate_srp(core_if); ++ } ++ ++ dctl.b.rmtwkupsig = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs-> ++ dctl, 0, dctl.d32); ++ DWC_DEBUGPL(DBG_PCD, "Set Remote Wakeup\n"); ++ ++ dwc_mdelay(2); ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs-> ++ dctl, dctl.d32, 0); ++ DWC_DEBUGPL(DBG_PCD, "Clear Remote Wakeup\n"); ++ } ++ } else { ++ DWC_DEBUGPL(DBG_PCD, "Remote Wakeup is disabled\n"); ++ } ++} ++ ++#ifdef CONFIG_USB_DWC_OTG_LPM ++/** ++ * This function initiates remote wakeup of the host from L1 sleep state. ++ */ ++void dwc_otg_pcd_rem_wkup_from_sleep(dwc_otg_pcd_t * pcd, int set) ++{ ++ glpmcfg_data_t lpmcfg; ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ ++ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ ++ /* Check if we are in L1 state */ ++ if (!lpmcfg.b.prt_sleep_sts) { ++ DWC_DEBUGPL(DBG_PCD, "Device is not in sleep state\n"); ++ return; ++ } ++ ++ /* Check if host allows remote wakeup */ ++ if (!lpmcfg.b.rem_wkup_en) { ++ DWC_DEBUGPL(DBG_PCD, "Host does not allow remote wakeup\n"); ++ return; ++ } ++ ++ /* Check if Resume OK */ ++ if (!lpmcfg.b.sleep_state_resumeok) { ++ DWC_DEBUGPL(DBG_PCD, "Sleep state resume is not OK\n"); ++ return; ++ } ++ ++ lpmcfg.d32 = DWC_READ_REG32(&core_if->core_global_regs->glpmcfg); ++ lpmcfg.b.en_utmi_sleep = 0; ++ lpmcfg.b.hird_thres &= (~(1 << 4)); ++ DWC_WRITE_REG32(&core_if->core_global_regs->glpmcfg, lpmcfg.d32); ++ ++ if (set) { ++ dctl_data_t dctl = {.d32 = 0 }; ++ dctl.b.rmtwkupsig = 1; ++ /* Set RmtWkUpSig bit to start remote wakup signaling. ++ * Hardware will automatically clear this bit. ++ */ ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, ++ 0, dctl.d32); ++ DWC_DEBUGPL(DBG_PCD, "Set Remote Wakeup\n"); ++ } ++ ++} ++#endif ++ ++/** ++ * Performs remote wakeup. ++ */ ++void dwc_otg_pcd_remote_wakeup(dwc_otg_pcd_t * pcd, int set) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dwc_irqflags_t flags; ++ if (dwc_otg_is_device_mode(core_if)) { ++ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags); ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ if (core_if->lx_state == DWC_OTG_L1) { ++ dwc_otg_pcd_rem_wkup_from_sleep(pcd, set); ++ } else { ++#endif ++ dwc_otg_pcd_rem_wkup_from_suspend(pcd, set); ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ } ++#endif ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++ } ++ return; ++} ++ ++void dwc_otg_pcd_disconnect_us(dwc_otg_pcd_t * pcd, int no_of_usecs) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dctl_data_t dctl = { 0 }; ++ ++ if (dwc_otg_is_device_mode(core_if)) { ++ dctl.b.sftdiscon = 1; ++ DWC_PRINTF("Soft disconnect for %d useconds\n",no_of_usecs); ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, 0, dctl.d32); ++ dwc_udelay(no_of_usecs); ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32,0); ++ ++ } else{ ++ DWC_PRINTF("NOT SUPPORTED IN HOST MODE\n"); ++ } ++ return; ++ ++} ++ ++int dwc_otg_pcd_wakeup(dwc_otg_pcd_t * pcd) ++{ ++ dsts_data_t dsts; ++ gotgctl_data_t gotgctl; ++ ++ /* ++ * This function starts the Protocol if no session is in progress. If ++ * a session is already in progress, but the device is suspended, ++ * remote wakeup signaling is started. ++ */ ++ ++ /* Check if valid session */ ++ gotgctl.d32 = ++ DWC_READ_REG32(&(GET_CORE_IF(pcd)->core_global_regs->gotgctl)); ++ if (gotgctl.b.bsesvld) { ++ /* Check if suspend state */ ++ dsts.d32 = ++ DWC_READ_REG32(& ++ (GET_CORE_IF(pcd)->dev_if-> ++ dev_global_regs->dsts)); ++ if (dsts.b.suspsts) { ++ dwc_otg_pcd_remote_wakeup(pcd, 1); ++ } ++ } else { ++ dwc_otg_pcd_initiate_srp(pcd); ++ } ++ ++ return 0; ++ ++} ++ ++/** ++ * Start the SRP timer to detect when the SRP does not complete within ++ * 6 seconds. ++ * ++ * @param pcd the pcd structure. ++ */ ++void dwc_otg_pcd_initiate_srp(dwc_otg_pcd_t * pcd) ++{ ++ dwc_irqflags_t flags; ++ DWC_SPINLOCK_IRQSAVE(pcd->lock, &flags); ++ dwc_otg_initiate_srp(GET_CORE_IF(pcd)); ++ DWC_SPINUNLOCK_IRQRESTORE(pcd->lock, flags); ++} ++ ++int dwc_otg_pcd_get_frame_number(dwc_otg_pcd_t * pcd) ++{ ++ return dwc_otg_get_frame_number(GET_CORE_IF(pcd)); ++} ++ ++int dwc_otg_pcd_is_lpm_enabled(dwc_otg_pcd_t * pcd) ++{ ++ return GET_CORE_IF(pcd)->core_params->lpm_enable; ++} ++ ++uint32_t get_b_hnp_enable(dwc_otg_pcd_t * pcd) ++{ ++ return pcd->b_hnp_enable; ++} ++ ++uint32_t get_a_hnp_support(dwc_otg_pcd_t * pcd) ++{ ++ return pcd->a_hnp_support; ++} ++ ++uint32_t get_a_alt_hnp_support(dwc_otg_pcd_t * pcd) ++{ ++ return pcd->a_alt_hnp_support; ++} ++ ++int dwc_otg_pcd_get_rmwkup_enable(dwc_otg_pcd_t * pcd) ++{ ++ return pcd->remote_wakeup_enable; ++} ++ ++#endif /* DWC_HOST_ONLY */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_pcd.h +@@ -0,0 +1,273 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_pcd.h $ ++ * $Revision: #48 $ ++ * $Date: 2012/08/10 $ ++ * $Change: 2047372 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++#ifndef DWC_HOST_ONLY ++#if !defined(__DWC_PCD_H__) ++#define __DWC_PCD_H__ ++ ++#include "dwc_otg_os_dep.h" ++#include "usb.h" ++#include "dwc_otg_cil.h" ++#include "dwc_otg_pcd_if.h" ++#include "dwc_otg_driver.h" ++ ++struct cfiobject; ++ ++/** ++ * @file ++ * ++ * This file contains the structures, constants, and interfaces for ++ * the Perpherial Contoller Driver (PCD). ++ * ++ * The Peripheral Controller Driver (PCD) for Linux will implement the ++ * Gadget API, so that the existing Gadget drivers can be used. For ++ * the Mass Storage Function driver the File-backed USB Storage Gadget ++ * (FBS) driver will be used. The FBS driver supports the ++ * Control-Bulk (CB), Control-Bulk-Interrupt (CBI), and Bulk-Only ++ * transports. ++ * ++ */ ++ ++/** Invalid DMA Address */ ++#define DWC_DMA_ADDR_INVALID (~(dwc_dma_t)0) ++ ++/** Max Transfer size for any EP */ ++#define DDMA_MAX_TRANSFER_SIZE 65535 ++ ++/** ++ * Get the pointer to the core_if from the pcd pointer. ++ */ ++#define GET_CORE_IF( _pcd ) (_pcd->core_if) ++ ++/** ++ * States of EP0. ++ */ ++typedef enum ep0_state { ++ EP0_DISCONNECT, /* no host */ ++ EP0_IDLE, ++ EP0_IN_DATA_PHASE, ++ EP0_OUT_DATA_PHASE, ++ EP0_IN_STATUS_PHASE, ++ EP0_OUT_STATUS_PHASE, ++ EP0_STALL, ++} ep0state_e; ++ ++/** Fordward declaration.*/ ++struct dwc_otg_pcd; ++ ++/** DWC_otg iso request structure. ++ * ++ */ ++typedef struct usb_iso_request dwc_otg_pcd_iso_request_t; ++ ++#ifdef DWC_UTE_PER_IO ++ ++/** ++ * This shall be the exact analogy of the same type structure defined in the ++ * usb_gadget.h. Each descriptor contains ++ */ ++struct dwc_iso_pkt_desc_port { ++ uint32_t offset; ++ uint32_t length; /* expected length */ ++ uint32_t actual_length; ++ uint32_t status; ++}; ++ ++struct dwc_iso_xreq_port { ++ /** transfer/submission flag */ ++ uint32_t tr_sub_flags; ++ /** Start the request ASAP */ ++#define DWC_EREQ_TF_ASAP 0x00000002 ++ /** Just enqueue the request w/o initiating a transfer */ ++#define DWC_EREQ_TF_ENQUEUE 0x00000004 ++ ++ /** ++ * count of ISO packets attached to this request - shall ++ * not exceed the pio_alloc_pkt_count ++ */ ++ uint32_t pio_pkt_count; ++ /** count of ISO packets allocated for this request */ ++ uint32_t pio_alloc_pkt_count; ++ /** number of ISO packet errors */ ++ uint32_t error_count; ++ /** reserved for future extension */ ++ uint32_t res; ++ /** Will be allocated and freed in the UTE gadget and based on the CFC value */ ++ struct dwc_iso_pkt_desc_port *per_io_frame_descs; ++}; ++#endif ++/** DWC_otg request structure. ++ * This structure is a list of requests. ++ */ ++typedef struct dwc_otg_pcd_request { ++ void *priv; ++ void *buf; ++ dwc_dma_t dma; ++ uint32_t length; ++ uint32_t actual; ++ unsigned sent_zlp:1; ++ /** ++ * Used instead of original buffer if ++ * it(physical address) is not dword-aligned. ++ **/ ++ uint8_t *dw_align_buf; ++ dwc_dma_t dw_align_buf_dma; ++ ++ DWC_CIRCLEQ_ENTRY(dwc_otg_pcd_request) queue_entry; ++#ifdef DWC_UTE_PER_IO ++ struct dwc_iso_xreq_port ext_req; ++ //void *priv_ereq_nport; /* */ ++#endif ++} dwc_otg_pcd_request_t; ++ ++DWC_CIRCLEQ_HEAD(req_list, dwc_otg_pcd_request); ++ ++/** PCD EP structure. ++ * This structure describes an EP, there is an array of EPs in the PCD ++ * structure. ++ */ ++typedef struct dwc_otg_pcd_ep { ++ /** USB EP Descriptor */ ++ const usb_endpoint_descriptor_t *desc; ++ ++ /** queue of dwc_otg_pcd_requests. */ ++ struct req_list queue; ++ unsigned stopped:1; ++ unsigned disabling:1; ++ unsigned dma:1; ++ unsigned queue_sof:1; ++ ++#ifdef DWC_EN_ISOC ++ /** ISOC req handle passed */ ++ void *iso_req_handle; ++#endif //_EN_ISOC_ ++ ++ /** DWC_otg ep data. */ ++ dwc_ep_t dwc_ep; ++ ++ /** Pointer to PCD */ ++ struct dwc_otg_pcd *pcd; ++ ++ void *priv; ++} dwc_otg_pcd_ep_t; ++ ++/** DWC_otg PCD Structure. ++ * This structure encapsulates the data for the dwc_otg PCD. ++ */ ++struct dwc_otg_pcd { ++ const struct dwc_otg_pcd_function_ops *fops; ++ /** The DWC otg device pointer */ ++ struct dwc_otg_device *otg_dev; ++ /** Core Interface */ ++ dwc_otg_core_if_t *core_if; ++ /** State of EP0 */ ++ ep0state_e ep0state; ++ /** EP0 Request is pending */ ++ unsigned ep0_pending:1; ++ /** Indicates when SET CONFIGURATION Request is in process */ ++ unsigned request_config:1; ++ /** The state of the Remote Wakeup Enable. */ ++ unsigned remote_wakeup_enable:1; ++ /** The state of the B-Device HNP Enable. */ ++ unsigned b_hnp_enable:1; ++ /** The state of A-Device HNP Support. */ ++ unsigned a_hnp_support:1; ++ /** The state of the A-Device Alt HNP support. */ ++ unsigned a_alt_hnp_support:1; ++ /** Count of pending Requests */ ++ unsigned request_pending; ++ ++ /** SETUP packet for EP0 ++ * This structure is allocated as a DMA buffer on PCD initialization ++ * with enough space for up to 3 setup packets. ++ */ ++ union { ++ usb_device_request_t req; ++ uint32_t d32[2]; ++ } *setup_pkt; ++ ++ dwc_dma_t setup_pkt_dma_handle; ++ ++ /* Additional buffer and flag for CTRL_WR premature case */ ++ uint8_t *backup_buf; ++ unsigned data_terminated; ++ ++ /** 2-byte dma buffer used to return status from GET_STATUS */ ++ uint16_t *status_buf; ++ dwc_dma_t status_buf_dma_handle; ++ ++ /** EP0 */ ++ dwc_otg_pcd_ep_t ep0; ++ ++ /** Array of IN EPs. */ ++ dwc_otg_pcd_ep_t in_ep[MAX_EPS_CHANNELS - 1]; ++ /** Array of OUT EPs. */ ++ dwc_otg_pcd_ep_t out_ep[MAX_EPS_CHANNELS - 1]; ++ /** number of valid EPs in the above array. */ ++// unsigned num_eps : 4; ++ dwc_spinlock_t *lock; ++ ++ /** Tasklet to defer starting of TEST mode transmissions until ++ * Status Phase has been completed. ++ */ ++ dwc_tasklet_t *test_mode_tasklet; ++ ++ /** Tasklet to delay starting of xfer in DMA mode */ ++ dwc_tasklet_t *start_xfer_tasklet; ++ ++ /** The test mode to enter when the tasklet is executed. */ ++ unsigned test_mode; ++ /** The cfi_api structure that implements most of the CFI API ++ * and OTG specific core configuration functionality ++ */ ++#ifdef DWC_UTE_CFI ++ struct cfiobject *cfi; ++#endif ++ ++}; ++ ++static inline struct device *dwc_otg_pcd_to_dev(struct dwc_otg_pcd *pcd) ++{ ++ return &pcd->otg_dev->os_dep.platformdev->dev; ++} ++ ++//FIXME this functions should be static, and this prototypes should be removed ++extern void dwc_otg_request_nuke(dwc_otg_pcd_ep_t * ep); ++extern void dwc_otg_request_done(dwc_otg_pcd_ep_t * ep, ++ dwc_otg_pcd_request_t * req, int32_t status); ++ ++void dwc_otg_iso_buffer_done(dwc_otg_pcd_t * pcd, dwc_otg_pcd_ep_t * ep, ++ void *req_handle); ++ ++extern void do_test_mode(void *data); ++#endif ++#endif /* DWC_HOST_ONLY */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_pcd_if.h +@@ -0,0 +1,361 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_pcd_if.h $ ++ * $Revision: #11 $ ++ * $Date: 2011/10/26 $ ++ * $Change: 1873028 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++#ifndef DWC_HOST_ONLY ++ ++#if !defined(__DWC_PCD_IF_H__) ++#define __DWC_PCD_IF_H__ ++ ++//#include "dwc_os.h" ++#include "dwc_otg_core_if.h" ++#include "dwc_otg_driver.h" ++ ++/** @file ++ * This file defines DWC_OTG PCD Core API. ++ */ ++ ++struct dwc_otg_pcd; ++typedef struct dwc_otg_pcd dwc_otg_pcd_t; ++ ++/** Maxpacket size for EP0 */ ++#define MAX_EP0_SIZE 64 ++/** Maxpacket size for any EP */ ++#define MAX_PACKET_SIZE 1024 ++ ++/** @name Function Driver Callbacks */ ++/** @{ */ ++ ++/** This function will be called whenever a previously queued request has ++ * completed. The status value will be set to -DWC_E_SHUTDOWN to indicated a ++ * failed or aborted transfer, or -DWC_E_RESTART to indicate the device was reset, ++ * or -DWC_E_TIMEOUT to indicate it timed out, or -DWC_E_INVALID to indicate invalid ++ * parameters. */ ++typedef int (*dwc_completion_cb_t) (dwc_otg_pcd_t * pcd, void *ep_handle, ++ void *req_handle, int32_t status, ++ uint32_t actual); ++/** ++ * This function will be called whenever a previousle queued ISOC request has ++ * completed. Count of ISOC packets could be read using dwc_otg_pcd_get_iso_packet_count ++ * function. ++ * The status of each ISOC packet could be read using dwc_otg_pcd_get_iso_packet_* ++ * functions. ++ */ ++typedef int (*dwc_isoc_completion_cb_t) (dwc_otg_pcd_t * pcd, void *ep_handle, ++ void *req_handle, int proc_buf_num); ++/** This function should handle any SETUP request that cannot be handled by the ++ * PCD Core. This includes most GET_DESCRIPTORs, SET_CONFIGS, Any ++ * class-specific requests, etc. The function must non-blocking. ++ * ++ * Returns 0 on success. ++ * Returns -DWC_E_NOT_SUPPORTED if the request is not supported. ++ * Returns -DWC_E_INVALID if the setup request had invalid parameters or bytes. ++ * Returns -DWC_E_SHUTDOWN on any other error. */ ++typedef int (*dwc_setup_cb_t) (dwc_otg_pcd_t * pcd, uint8_t * bytes); ++/** This is called whenever the device has been disconnected. The function ++ * driver should take appropriate action to clean up all pending requests in the ++ * PCD Core, remove all endpoints (except ep0), and initialize back to reset ++ * state. */ ++typedef int (*dwc_disconnect_cb_t) (dwc_otg_pcd_t * pcd); ++/** This function is called when device has been connected. */ ++typedef int (*dwc_connect_cb_t) (dwc_otg_pcd_t * pcd, int speed); ++/** This function is called when device has been suspended */ ++typedef int (*dwc_suspend_cb_t) (dwc_otg_pcd_t * pcd); ++/** This function is called when device has received LPM tokens, i.e. ++ * device has been sent to sleep state. */ ++typedef int (*dwc_sleep_cb_t) (dwc_otg_pcd_t * pcd); ++/** This function is called when device has been resumed ++ * from suspend(L2) or L1 sleep state. */ ++typedef int (*dwc_resume_cb_t) (dwc_otg_pcd_t * pcd); ++/** This function is called whenever hnp params has been changed. ++ * User can call get_b_hnp_enable, get_a_hnp_support, get_a_alt_hnp_support functions ++ * to get hnp parameters. */ ++typedef int (*dwc_hnp_params_changed_cb_t) (dwc_otg_pcd_t * pcd); ++/** This function is called whenever USB RESET is detected. */ ++typedef int (*dwc_reset_cb_t) (dwc_otg_pcd_t * pcd); ++ ++typedef int (*cfi_setup_cb_t) (dwc_otg_pcd_t * pcd, void *ctrl_req_bytes); ++ ++/** ++ * ++ * @param ep_handle Void pointer to the usb_ep structure ++ * @param ereq_port Pointer to the extended request structure created in the ++ * portable part. ++ */ ++typedef int (*xiso_completion_cb_t) (dwc_otg_pcd_t * pcd, void *ep_handle, ++ void *req_handle, int32_t status, ++ void *ereq_port); ++/** Function Driver Ops Data Structure */ ++struct dwc_otg_pcd_function_ops { ++ dwc_connect_cb_t connect; ++ dwc_disconnect_cb_t disconnect; ++ dwc_setup_cb_t setup; ++ dwc_completion_cb_t complete; ++ dwc_isoc_completion_cb_t isoc_complete; ++ dwc_suspend_cb_t suspend; ++ dwc_sleep_cb_t sleep; ++ dwc_resume_cb_t resume; ++ dwc_reset_cb_t reset; ++ dwc_hnp_params_changed_cb_t hnp_changed; ++ cfi_setup_cb_t cfi_setup; ++#ifdef DWC_UTE_PER_IO ++ xiso_completion_cb_t xisoc_complete; ++#endif ++}; ++/** @} */ ++ ++/** @name Function Driver Functions */ ++/** @{ */ ++ ++/** Call this function to get pointer on dwc_otg_pcd_t, ++ * this pointer will be used for all PCD API functions. ++ * ++ * @param core_if The DWC_OTG Core ++ */ ++extern dwc_otg_pcd_t *dwc_otg_pcd_init(dwc_otg_device_t *otg_dev); ++ ++/** Frees PCD allocated by dwc_otg_pcd_init ++ * ++ * @param pcd The PCD ++ */ ++extern void dwc_otg_pcd_remove(dwc_otg_pcd_t * pcd); ++ ++/** Call this to bind the function driver to the PCD Core. ++ * ++ * @param pcd Pointer on dwc_otg_pcd_t returned by dwc_otg_pcd_init function. ++ * @param fops The Function Driver Ops data structure containing pointers to all callbacks. ++ */ ++extern void dwc_otg_pcd_start(dwc_otg_pcd_t * pcd, ++ const struct dwc_otg_pcd_function_ops *fops); ++ ++/** Enables an endpoint for use. This function enables an endpoint in ++ * the PCD. The endpoint is described by the ep_desc which has the ++ * same format as a USB ep descriptor. The ep_handle parameter is used to refer ++ * to the endpoint from other API functions and in callbacks. Normally this ++ * should be called after a SET_CONFIGURATION/SET_INTERFACE to configure the ++ * core for that interface. ++ * ++ * Returns -DWC_E_INVALID if invalid parameters were passed. ++ * Returns -DWC_E_SHUTDOWN if any other error ocurred. ++ * Returns 0 on success. ++ * ++ * @param pcd The PCD ++ * @param ep_desc Endpoint descriptor ++ * @param usb_ep Handle on endpoint, that will be used to identify endpoint. ++ */ ++extern int dwc_otg_pcd_ep_enable(dwc_otg_pcd_t * pcd, ++ const uint8_t * ep_desc, void *usb_ep); ++ ++/** Disable the endpoint referenced by ep_handle. ++ * ++ * Returns -DWC_E_INVALID if invalid parameters were passed. ++ * Returns -DWC_E_SHUTDOWN if any other error occurred. ++ * Returns 0 on success. */ ++extern int dwc_otg_pcd_ep_disable(dwc_otg_pcd_t * pcd, void *ep_handle); ++ ++/** Queue a data transfer request on the endpoint referenced by ep_handle. ++ * After the transfer is completes, the complete callback will be called with ++ * the request status. ++ * ++ * @param pcd The PCD ++ * @param ep_handle The handle of the endpoint ++ * @param buf The buffer for the data ++ * @param dma_buf The DMA buffer for the data ++ * @param buflen The length of the data transfer ++ * @param zero Specifies whether to send zero length last packet. ++ * @param req_handle Set this handle to any value to use to reference this ++ * request in the ep_dequeue function or from the complete callback ++ * @param atomic_alloc If driver need to perform atomic allocations ++ * for internal data structures. ++ * ++ * Returns -DWC_E_INVALID if invalid parameters were passed. ++ * Returns -DWC_E_SHUTDOWN if any other error ocurred. ++ * Returns 0 on success. */ ++extern int dwc_otg_pcd_ep_queue(dwc_otg_pcd_t * pcd, void *ep_handle, ++ uint8_t * buf, dwc_dma_t dma_buf, ++ uint32_t buflen, int zero, void *req_handle, ++ int atomic_alloc); ++#ifdef DWC_UTE_PER_IO ++/** ++ * ++ * @param ereq_nonport Pointer to the extended request part of the ++ * usb_request structure defined in usb_gadget.h file. ++ */ ++extern int dwc_otg_pcd_xiso_ep_queue(dwc_otg_pcd_t * pcd, void *ep_handle, ++ uint8_t * buf, dwc_dma_t dma_buf, ++ uint32_t buflen, int zero, ++ void *req_handle, int atomic_alloc, ++ void *ereq_nonport); ++ ++#endif ++ ++/** De-queue the specified data transfer that has not yet completed. ++ * ++ * Returns -DWC_E_INVALID if invalid parameters were passed. ++ * Returns -DWC_E_SHUTDOWN if any other error ocurred. ++ * Returns 0 on success. */ ++extern int dwc_otg_pcd_ep_dequeue(dwc_otg_pcd_t * pcd, void *ep_handle, ++ void *req_handle); ++ ++/** Halt (STALL) an endpoint or clear it. ++ * ++ * Returns -DWC_E_INVALID if invalid parameters were passed. ++ * Returns -DWC_E_SHUTDOWN if any other error ocurred. ++ * Returns -DWC_E_AGAIN if the STALL cannot be sent and must be tried again later ++ * Returns 0 on success. */ ++extern int dwc_otg_pcd_ep_halt(dwc_otg_pcd_t * pcd, void *ep_handle, int value); ++ ++/** This function */ ++extern int dwc_otg_pcd_ep_wedge(dwc_otg_pcd_t * pcd, void *ep_handle); ++ ++/** This function should be called on every hardware interrupt */ ++extern int32_t dwc_otg_pcd_handle_intr(dwc_otg_pcd_t * pcd); ++ ++/** This function returns current frame number */ ++extern int dwc_otg_pcd_get_frame_number(dwc_otg_pcd_t * pcd); ++ ++/** ++ * Start isochronous transfers on the endpoint referenced by ep_handle. ++ * For isochronous transfers duble buffering is used. ++ * After processing each of buffers comlete callback will be called with ++ * status for each transaction. ++ * ++ * @param pcd The PCD ++ * @param ep_handle The handle of the endpoint ++ * @param buf0 The virtual address of first data buffer ++ * @param buf1 The virtual address of second data buffer ++ * @param dma0 The DMA address of first data buffer ++ * @param dma1 The DMA address of second data buffer ++ * @param sync_frame Data pattern frame number ++ * @param dp_frame Data size for pattern frame ++ * @param data_per_frame Data size for regular frame ++ * @param start_frame Frame number to start transfers, if -1 then start transfers ASAP. ++ * @param buf_proc_intrvl Interval of ISOC Buffer processing ++ * @param req_handle Handle of ISOC request ++ * @param atomic_alloc Specefies whether to perform atomic allocation for ++ * internal data structures. ++ * ++ * Returns -DWC_E_NO_MEMORY if there is no enough memory. ++ * Returns -DWC_E_INVALID if incorrect arguments are passed to the function. ++ * Returns -DW_E_SHUTDOWN for any other error. ++ * Returns 0 on success ++ */ ++extern int dwc_otg_pcd_iso_ep_start(dwc_otg_pcd_t * pcd, void *ep_handle, ++ uint8_t * buf0, uint8_t * buf1, ++ dwc_dma_t dma0, dwc_dma_t dma1, ++ int sync_frame, int dp_frame, ++ int data_per_frame, int start_frame, ++ int buf_proc_intrvl, void *req_handle, ++ int atomic_alloc); ++ ++/** Stop ISOC transfers on endpoint referenced by ep_handle. ++ * ++ * @param pcd The PCD ++ * @param ep_handle The handle of the endpoint ++ * @param req_handle Handle of ISOC request ++ * ++ * Returns -DWC_E_INVALID if incorrect arguments are passed to the function ++ * Returns 0 on success ++ */ ++int dwc_otg_pcd_iso_ep_stop(dwc_otg_pcd_t * pcd, void *ep_handle, ++ void *req_handle); ++ ++/** Get ISOC packet status. ++ * ++ * @param pcd The PCD ++ * @param ep_handle The handle of the endpoint ++ * @param iso_req_handle Isochronoush request handle ++ * @param packet Number of packet ++ * @param status Out parameter for returning status ++ * @param actual Out parameter for returning actual length ++ * @param offset Out parameter for returning offset ++ * ++ */ ++extern void dwc_otg_pcd_get_iso_packet_params(dwc_otg_pcd_t * pcd, ++ void *ep_handle, ++ void *iso_req_handle, int packet, ++ int *status, int *actual, ++ int *offset); ++ ++/** Get ISOC packet count. ++ * ++ * @param pcd The PCD ++ * @param ep_handle The handle of the endpoint ++ * @param iso_req_handle ++ */ ++extern int dwc_otg_pcd_get_iso_packet_count(dwc_otg_pcd_t * pcd, ++ void *ep_handle, ++ void *iso_req_handle); ++ ++/** This function starts the SRP Protocol if no session is in progress. If ++ * a session is already in progress, but the device is suspended, ++ * remote wakeup signaling is started. ++ */ ++extern int dwc_otg_pcd_wakeup(dwc_otg_pcd_t * pcd); ++ ++/** This function returns 1 if LPM support is enabled, and 0 otherwise. */ ++extern int dwc_otg_pcd_is_lpm_enabled(dwc_otg_pcd_t * pcd); ++ ++/** This function returns 1 if remote wakeup is allowed and 0, otherwise. */ ++extern int dwc_otg_pcd_get_rmwkup_enable(dwc_otg_pcd_t * pcd); ++ ++/** Initiate SRP */ ++extern void dwc_otg_pcd_initiate_srp(dwc_otg_pcd_t * pcd); ++ ++/** Starts remote wakeup signaling. */ ++extern void dwc_otg_pcd_remote_wakeup(dwc_otg_pcd_t * pcd, int set); ++ ++/** Starts micorsecond soft disconnect. */ ++extern void dwc_otg_pcd_disconnect_us(dwc_otg_pcd_t * pcd, int no_of_usecs); ++/** This function returns whether device is dualspeed.*/ ++extern uint32_t dwc_otg_pcd_is_dualspeed(dwc_otg_pcd_t * pcd); ++ ++/** This function returns whether device is otg. */ ++extern uint32_t dwc_otg_pcd_is_otg(dwc_otg_pcd_t * pcd); ++ ++/** These functions allow to get hnp parameters */ ++extern uint32_t get_b_hnp_enable(dwc_otg_pcd_t * pcd); ++extern uint32_t get_a_hnp_support(dwc_otg_pcd_t * pcd); ++extern uint32_t get_a_alt_hnp_support(dwc_otg_pcd_t * pcd); ++ ++/** CFI specific Interface functions */ ++/** Allocate a cfi buffer */ ++extern uint8_t *cfiw_ep_alloc_buffer(dwc_otg_pcd_t * pcd, void *pep, ++ dwc_dma_t * addr, size_t buflen, ++ int flags); ++ ++/******************************************************************************/ ++ ++/** @} */ ++ ++#endif /* __DWC_PCD_IF_H__ */ ++ ++#endif /* DWC_HOST_ONLY */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_pcd_intr.c +@@ -0,0 +1,5148 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_pcd_intr.c $ ++ * $Revision: #116 $ ++ * $Date: 2012/08/10 $ ++ * $Change: 2047372 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++#ifndef DWC_HOST_ONLY ++ ++#include "dwc_otg_pcd.h" ++ ++#ifdef DWC_UTE_CFI ++#include "dwc_otg_cfi.h" ++#endif ++ ++#ifdef DWC_UTE_PER_IO ++extern void complete_xiso_ep(dwc_otg_pcd_ep_t * ep); ++#endif ++//#define PRINT_CFI_DMA_DESCS ++ ++#define DEBUG_EP0 ++ ++/** ++ * This function updates OTG. ++ */ ++static void dwc_otg_pcd_update_otg(dwc_otg_pcd_t * pcd, const unsigned reset) ++{ ++ ++ if (reset) { ++ pcd->b_hnp_enable = 0; ++ pcd->a_hnp_support = 0; ++ pcd->a_alt_hnp_support = 0; ++ } ++ ++ if (pcd->fops->hnp_changed) { ++ pcd->fops->hnp_changed(pcd); ++ } ++} ++ ++/** @file ++ * This file contains the implementation of the PCD Interrupt handlers. ++ * ++ * The PCD handles the device interrupts. Many conditions can cause a ++ * device interrupt. When an interrupt occurs, the device interrupt ++ * service routine determines the cause of the interrupt and ++ * dispatches handling to the appropriate function. These interrupt ++ * handling functions are described below. ++ * All interrupt registers are processed from LSB to MSB. ++ */ ++ ++/** ++ * This function prints the ep0 state for debug purposes. ++ */ ++static inline void print_ep0_state(dwc_otg_pcd_t * pcd) ++{ ++#ifdef DEBUG ++ char str[40]; ++ ++ switch (pcd->ep0state) { ++ case EP0_DISCONNECT: ++ dwc_strcpy(str, "EP0_DISCONNECT"); ++ break; ++ case EP0_IDLE: ++ dwc_strcpy(str, "EP0_IDLE"); ++ break; ++ case EP0_IN_DATA_PHASE: ++ dwc_strcpy(str, "EP0_IN_DATA_PHASE"); ++ break; ++ case EP0_OUT_DATA_PHASE: ++ dwc_strcpy(str, "EP0_OUT_DATA_PHASE"); ++ break; ++ case EP0_IN_STATUS_PHASE: ++ dwc_strcpy(str, "EP0_IN_STATUS_PHASE"); ++ break; ++ case EP0_OUT_STATUS_PHASE: ++ dwc_strcpy(str, "EP0_OUT_STATUS_PHASE"); ++ break; ++ case EP0_STALL: ++ dwc_strcpy(str, "EP0_STALL"); ++ break; ++ default: ++ dwc_strcpy(str, "EP0_INVALID"); ++ } ++ ++ DWC_DEBUGPL(DBG_ANY, "%s(%d)\n", str, pcd->ep0state); ++#endif ++} ++ ++/** ++ * This function calculate the size of the payload in the memory ++ * for out endpoints and prints size for debug purposes(used in ++ * 2.93a DevOutNak feature). ++ */ ++static inline void print_memory_payload(dwc_otg_pcd_t * pcd, dwc_ep_t * ep) ++{ ++#ifdef DEBUG ++ deptsiz_data_t deptsiz_init = {.d32 = 0 }; ++ deptsiz_data_t deptsiz_updt = {.d32 = 0 }; ++ int pack_num; ++ unsigned payload; ++ ++ deptsiz_init.d32 = pcd->core_if->start_doeptsiz_val[ep->num]; ++ deptsiz_updt.d32 = ++ DWC_READ_REG32(&pcd->core_if->dev_if-> ++ out_ep_regs[ep->num]->doeptsiz); ++ /* Payload will be */ ++ payload = deptsiz_init.b.xfersize - deptsiz_updt.b.xfersize; ++ /* Packet count is decremented every time a packet ++ * is written to the RxFIFO not in to the external memory ++ * So, if payload == 0, then it means no packet was sent to ext memory*/ ++ pack_num = (!payload) ? 0 : (deptsiz_init.b.pktcnt - deptsiz_updt.b.pktcnt); ++ DWC_DEBUGPL(DBG_PCDV, ++ "Payload for EP%d-%s\n", ++ ep->num, (ep->is_in ? "IN" : "OUT")); ++ DWC_DEBUGPL(DBG_PCDV, ++ "Number of transfered bytes = 0x%08x\n", payload); ++ DWC_DEBUGPL(DBG_PCDV, ++ "Number of transfered packets = %d\n", pack_num); ++#endif ++} ++ ++ ++#ifdef DWC_UTE_CFI ++static inline void print_desc(struct dwc_otg_dma_desc *ddesc, ++ const uint8_t * epname, int descnum) ++{ ++ CFI_INFO ++ ("%s DMA_DESC(%d) buf=0x%08x bytes=0x%04x; sp=0x%x; l=0x%x; sts=0x%02x; bs=0x%02x\n", ++ epname, descnum, ddesc->buf, ddesc->status.b.bytes, ++ ddesc->status.b.sp, ddesc->status.b.l, ddesc->status.b.sts, ++ ddesc->status.b.bs); ++} ++#endif ++ ++/** ++ * This function returns pointer to in ep struct with number ep_num ++ */ ++static inline dwc_otg_pcd_ep_t *get_in_ep(dwc_otg_pcd_t * pcd, uint32_t ep_num) ++{ ++ int i; ++ int num_in_eps = GET_CORE_IF(pcd)->dev_if->num_in_eps; ++ if (ep_num == 0) { ++ return &pcd->ep0; ++ } else { ++ for (i = 0; i < num_in_eps; ++i) { ++ if (pcd->in_ep[i].dwc_ep.num == ep_num) ++ return &pcd->in_ep[i]; ++ } ++ return 0; ++ } ++} ++ ++/** ++ * This function returns pointer to out ep struct with number ep_num ++ */ ++static inline dwc_otg_pcd_ep_t *get_out_ep(dwc_otg_pcd_t * pcd, uint32_t ep_num) ++{ ++ int i; ++ int num_out_eps = GET_CORE_IF(pcd)->dev_if->num_out_eps; ++ if (ep_num == 0) { ++ return &pcd->ep0; ++ } else { ++ for (i = 0; i < num_out_eps; ++i) { ++ if (pcd->out_ep[i].dwc_ep.num == ep_num) ++ return &pcd->out_ep[i]; ++ } ++ return 0; ++ } ++} ++ ++/** ++ * This functions gets a pointer to an EP from the wIndex address ++ * value of the control request. ++ */ ++dwc_otg_pcd_ep_t *get_ep_by_addr(dwc_otg_pcd_t * pcd, u16 wIndex) ++{ ++ dwc_otg_pcd_ep_t *ep; ++ uint32_t ep_num = UE_GET_ADDR(wIndex); ++ ++ if (ep_num == 0) { ++ ep = &pcd->ep0; ++ } else if (UE_GET_DIR(wIndex) == UE_DIR_IN) { /* in ep */ ++ ep = &pcd->in_ep[ep_num - 1]; ++ } else { ++ ep = &pcd->out_ep[ep_num - 1]; ++ } ++ ++ return ep; ++} ++ ++/** ++ * This function checks the EP request queue, if the queue is not ++ * empty the next request is started. ++ */ ++void start_next_request(dwc_otg_pcd_ep_t * ep) ++{ ++ dwc_otg_pcd_request_t *req = 0; ++ uint32_t max_transfer = ++ GET_CORE_IF(ep->pcd)->core_params->max_transfer_size; ++ ++#ifdef DWC_UTE_CFI ++ struct dwc_otg_pcd *pcd; ++ pcd = ep->pcd; ++#endif ++ ++ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) { ++ req = DWC_CIRCLEQ_FIRST(&ep->queue); ++ ++#ifdef DWC_UTE_CFI ++ if (ep->dwc_ep.buff_mode != BM_STANDARD) { ++ ep->dwc_ep.cfi_req_len = req->length; ++ pcd->cfi->ops.build_descriptors(pcd->cfi, pcd, ep, req); ++ } else { ++#endif ++ /* Setup and start the Transfer */ ++ if (req->dw_align_buf) { ++ ep->dwc_ep.dma_addr = req->dw_align_buf_dma; ++ ep->dwc_ep.start_xfer_buff = req->dw_align_buf; ++ ep->dwc_ep.xfer_buff = req->dw_align_buf; ++ } else { ++ ep->dwc_ep.dma_addr = req->dma; ++ ep->dwc_ep.start_xfer_buff = req->buf; ++ ep->dwc_ep.xfer_buff = req->buf; ++ } ++ ep->dwc_ep.sent_zlp = 0; ++ ep->dwc_ep.total_len = req->length; ++ ep->dwc_ep.xfer_len = 0; ++ ep->dwc_ep.xfer_count = 0; ++ ++ ep->dwc_ep.maxxfer = max_transfer; ++ if (GET_CORE_IF(ep->pcd)->dma_desc_enable) { ++ uint32_t out_max_xfer = DDMA_MAX_TRANSFER_SIZE ++ - (DDMA_MAX_TRANSFER_SIZE % 4); ++ if (ep->dwc_ep.is_in) { ++ if (ep->dwc_ep.maxxfer > ++ DDMA_MAX_TRANSFER_SIZE) { ++ ep->dwc_ep.maxxfer = ++ DDMA_MAX_TRANSFER_SIZE; ++ } ++ } else { ++ if (ep->dwc_ep.maxxfer > out_max_xfer) { ++ ep->dwc_ep.maxxfer = ++ out_max_xfer; ++ } ++ } ++ } ++ if (ep->dwc_ep.maxxfer < ep->dwc_ep.total_len) { ++ ep->dwc_ep.maxxfer -= ++ (ep->dwc_ep.maxxfer % ep->dwc_ep.maxpacket); ++ } ++ if (req->sent_zlp) { ++ if ((ep->dwc_ep.total_len % ++ ep->dwc_ep.maxpacket == 0) ++ && (ep->dwc_ep.total_len != 0)) { ++ ep->dwc_ep.sent_zlp = 1; ++ } ++ ++ } ++#ifdef DWC_UTE_CFI ++ } ++#endif ++ dwc_otg_ep_start_transfer(GET_CORE_IF(ep->pcd), &ep->dwc_ep); ++ } else if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) { ++ DWC_PRINTF("There are no more ISOC requests \n"); ++ ep->dwc_ep.frame_num = 0xFFFFFFFF; ++ } ++} ++ ++/** ++ * This function handles the SOF Interrupts. At this time the SOF ++ * Interrupt is disabled. ++ */ ++int32_t dwc_otg_pcd_handle_sof_intr(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ ++ gintsts_data_t gintsts; ++ ++ DWC_DEBUGPL(DBG_PCD, "SOF\n"); ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.sofintr = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ ++ return 1; ++} ++ ++/** ++ * This function handles the Rx Status Queue Level Interrupt, which ++ * indicates that there is a least one packet in the Rx FIFO. The ++ * packets are moved from the FIFO to memory, where they will be ++ * processed when the Endpoint Interrupt Register indicates Transfer ++ * Complete or SETUP Phase Done. ++ * ++ * Repeat the following until the Rx Status Queue is empty: ++ * -# Read the Receive Status Pop Register (GRXSTSP) to get Packet ++ * info ++ * -# If Receive FIFO is empty then skip to step Clear the interrupt ++ * and exit ++ * -# If SETUP Packet call dwc_otg_read_setup_packet to copy the ++ * SETUP data to the buffer ++ * -# If OUT Data Packet call dwc_otg_read_packet to copy the data ++ * to the destination buffer ++ */ ++int32_t dwc_otg_pcd_handle_rx_status_q_level_intr(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ gintmsk_data_t gintmask = {.d32 = 0 }; ++ device_grxsts_data_t status; ++ dwc_otg_pcd_ep_t *ep; ++ gintsts_data_t gintsts; ++#ifdef DEBUG ++ static char *dpid_str[] = { "D0", "D2", "D1", "MDATA" }; ++#endif ++ ++ //DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, _pcd); ++ /* Disable the Rx Status Queue Level interrupt */ ++ gintmask.b.rxstsqlvl = 1; ++ DWC_MODIFY_REG32(&global_regs->gintmsk, gintmask.d32, 0); ++ ++ /* Get the Status from the top of the FIFO */ ++ status.d32 = DWC_READ_REG32(&global_regs->grxstsp); ++ ++ DWC_DEBUGPL(DBG_PCD, "EP:%d BCnt:%d DPID:%s " ++ "pktsts:%x Frame:%d(0x%0x)\n", ++ status.b.epnum, status.b.bcnt, ++ dpid_str[status.b.dpid], ++ status.b.pktsts, status.b.fn, status.b.fn); ++ /* Get pointer to EP structure */ ++ ep = get_out_ep(pcd, status.b.epnum); ++ ++ switch (status.b.pktsts) { ++ case DWC_DSTS_GOUT_NAK: ++ DWC_DEBUGPL(DBG_PCDV, "Global OUT NAK\n"); ++ break; ++ case DWC_STS_DATA_UPDT: ++ DWC_DEBUGPL(DBG_PCDV, "OUT Data Packet\n"); ++ if (status.b.bcnt && ep->dwc_ep.xfer_buff) { ++ /** @todo NGS Check for buffer overflow? */ ++ dwc_otg_read_packet(core_if, ++ ep->dwc_ep.xfer_buff, ++ status.b.bcnt); ++ ep->dwc_ep.xfer_count += status.b.bcnt; ++ ep->dwc_ep.xfer_buff += status.b.bcnt; ++ } ++ break; ++ case DWC_STS_XFER_COMP: ++ DWC_DEBUGPL(DBG_PCDV, "OUT Complete\n"); ++ break; ++ case DWC_DSTS_SETUP_COMP: ++#ifdef DEBUG_EP0 ++ DWC_DEBUGPL(DBG_PCDV, "Setup Complete\n"); ++#endif ++ break; ++ case DWC_DSTS_SETUP_UPDT: ++ dwc_otg_read_setup_packet(core_if, pcd->setup_pkt->d32); ++#ifdef DEBUG_EP0 ++ DWC_DEBUGPL(DBG_PCD, ++ "SETUP PKT: %02x.%02x v%04x i%04x l%04x\n", ++ pcd->setup_pkt->req.bmRequestType, ++ pcd->setup_pkt->req.bRequest, ++ UGETW(pcd->setup_pkt->req.wValue), ++ UGETW(pcd->setup_pkt->req.wIndex), ++ UGETW(pcd->setup_pkt->req.wLength)); ++#endif ++ ep->dwc_ep.xfer_count += status.b.bcnt; ++ break; ++ default: ++ DWC_DEBUGPL(DBG_PCDV, "Invalid Packet Status (0x%0x)\n", ++ status.b.pktsts); ++ break; ++ } ++ ++ /* Enable the Rx Status Queue Level interrupt */ ++ DWC_MODIFY_REG32(&global_regs->gintmsk, 0, gintmask.d32); ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.rxstsqlvl = 1; ++ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32); ++ ++ //DWC_DEBUGPL(DBG_PCDV, "EXIT: %s\n", __func__); ++ return 1; ++} ++ ++/** ++ * This function examines the Device IN Token Learning Queue to ++ * determine the EP number of the last IN token received. This ++ * implementation is for the Mass Storage device where there are only ++ * 2 IN EPs (Control-IN and BULK-IN). ++ * ++ * The EP numbers for the first six IN Tokens are in DTKNQR1 and there ++ * are 8 EP Numbers in each of the other possible DTKNQ Registers. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * ++ */ ++static inline int get_ep_of_last_in_token(dwc_otg_core_if_t * core_if) ++{ ++ dwc_otg_device_global_regs_t *dev_global_regs = ++ core_if->dev_if->dev_global_regs; ++ const uint32_t TOKEN_Q_DEPTH = core_if->hwcfg2.b.dev_token_q_depth; ++ /* Number of Token Queue Registers */ ++ const int DTKNQ_REG_CNT = (TOKEN_Q_DEPTH + 7) / 8; ++ dtknq1_data_t dtknqr1; ++ uint32_t in_tkn_epnums[4]; ++ int ndx = 0; ++ int i = 0; ++ volatile uint32_t *addr = &dev_global_regs->dtknqr1; ++ int epnum = 0; ++ ++ //DWC_DEBUGPL(DBG_PCD,"dev_token_q_depth=%d\n",TOKEN_Q_DEPTH); ++ ++ /* Read the DTKNQ Registers */ ++ for (i = 0; i < DTKNQ_REG_CNT; i++) { ++ in_tkn_epnums[i] = DWC_READ_REG32(addr); ++ DWC_DEBUGPL(DBG_PCDV, "DTKNQR%d=0x%08x\n", i + 1, ++ in_tkn_epnums[i]); ++ if (addr == &dev_global_regs->dvbusdis) { ++ addr = &dev_global_regs->dtknqr3_dthrctl; ++ } else { ++ ++addr; ++ } ++ ++ } ++ ++ /* Copy the DTKNQR1 data to the bit field. */ ++ dtknqr1.d32 = in_tkn_epnums[0]; ++ /* Get the EP numbers */ ++ in_tkn_epnums[0] = dtknqr1.b.epnums0_5; ++ ndx = dtknqr1.b.intknwptr - 1; ++ ++ //DWC_DEBUGPL(DBG_PCDV,"ndx=%d\n",ndx); ++ if (ndx == -1) { ++ /** @todo Find a simpler way to calculate the max ++ * queue position.*/ ++ int cnt = TOKEN_Q_DEPTH; ++ if (TOKEN_Q_DEPTH <= 6) { ++ cnt = TOKEN_Q_DEPTH - 1; ++ } else if (TOKEN_Q_DEPTH <= 14) { ++ cnt = TOKEN_Q_DEPTH - 7; ++ } else if (TOKEN_Q_DEPTH <= 22) { ++ cnt = TOKEN_Q_DEPTH - 15; ++ } else { ++ cnt = TOKEN_Q_DEPTH - 23; ++ } ++ epnum = (in_tkn_epnums[DTKNQ_REG_CNT - 1] >> (cnt * 4)) & 0xF; ++ } else { ++ if (ndx <= 5) { ++ epnum = (in_tkn_epnums[0] >> (ndx * 4)) & 0xF; ++ } else if (ndx <= 13) { ++ ndx -= 6; ++ epnum = (in_tkn_epnums[1] >> (ndx * 4)) & 0xF; ++ } else if (ndx <= 21) { ++ ndx -= 14; ++ epnum = (in_tkn_epnums[2] >> (ndx * 4)) & 0xF; ++ } else if (ndx <= 29) { ++ ndx -= 22; ++ epnum = (in_tkn_epnums[3] >> (ndx * 4)) & 0xF; ++ } ++ } ++ //DWC_DEBUGPL(DBG_PCD,"epnum=%d\n",epnum); ++ return epnum; ++} ++ ++/** ++ * This interrupt occurs when the non-periodic Tx FIFO is half-empty. ++ * The active request is checked for the next packet to be loaded into ++ * the non-periodic Tx FIFO. ++ */ ++int32_t dwc_otg_pcd_handle_np_tx_fifo_empty_intr(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ dwc_otg_dev_in_ep_regs_t *ep_regs; ++ gnptxsts_data_t txstatus = {.d32 = 0 }; ++ gintsts_data_t gintsts; ++ ++ int epnum = 0; ++ dwc_otg_pcd_ep_t *ep = 0; ++ uint32_t len = 0; ++ int dwords; ++ ++ /* Get the epnum from the IN Token Learning Queue. */ ++ epnum = get_ep_of_last_in_token(core_if); ++ ep = get_in_ep(pcd, epnum); ++ ++ DWC_DEBUGPL(DBG_PCD, "NP TxFifo Empty: %d \n", epnum); ++ ++ ep_regs = core_if->dev_if->in_ep_regs[epnum]; ++ ++ len = ep->dwc_ep.xfer_len - ep->dwc_ep.xfer_count; ++ if (len > ep->dwc_ep.maxpacket) { ++ len = ep->dwc_ep.maxpacket; ++ } ++ dwords = (len + 3) / 4; ++ ++ /* While there is space in the queue and space in the FIFO and ++ * More data to tranfer, Write packets to the Tx FIFO */ ++ txstatus.d32 = DWC_READ_REG32(&global_regs->gnptxsts); ++ DWC_DEBUGPL(DBG_PCDV, "b4 GNPTXSTS=0x%08x\n", txstatus.d32); ++ ++ while (txstatus.b.nptxqspcavail > 0 && ++ txstatus.b.nptxfspcavail > dwords && ++ ep->dwc_ep.xfer_count < ep->dwc_ep.xfer_len) { ++ /* Write the FIFO */ ++ dwc_otg_ep_write_packet(core_if, &ep->dwc_ep, 0); ++ len = ep->dwc_ep.xfer_len - ep->dwc_ep.xfer_count; ++ ++ if (len > ep->dwc_ep.maxpacket) { ++ len = ep->dwc_ep.maxpacket; ++ } ++ ++ dwords = (len + 3) / 4; ++ txstatus.d32 = DWC_READ_REG32(&global_regs->gnptxsts); ++ DWC_DEBUGPL(DBG_PCDV, "GNPTXSTS=0x%08x\n", txstatus.d32); ++ } ++ ++ DWC_DEBUGPL(DBG_PCDV, "GNPTXSTS=0x%08x\n", ++ DWC_READ_REG32(&global_regs->gnptxsts)); ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.nptxfempty = 1; ++ DWC_WRITE_REG32(&global_regs->gintsts, gintsts.d32); ++ ++ return 1; ++} ++ ++/** ++ * This function is called when dedicated Tx FIFO Empty interrupt occurs. ++ * The active request is checked for the next packet to be loaded into ++ * apropriate Tx FIFO. ++ */ ++static int32_t write_empty_tx_fifo(dwc_otg_pcd_t * pcd, uint32_t epnum) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ dwc_otg_dev_in_ep_regs_t *ep_regs; ++ dtxfsts_data_t txstatus = {.d32 = 0 }; ++ dwc_otg_pcd_ep_t *ep = 0; ++ uint32_t len = 0; ++ int dwords; ++ ++ ep = get_in_ep(pcd, epnum); ++ ++ DWC_DEBUGPL(DBG_PCD, "Dedicated TxFifo Empty: %d \n", epnum); ++ ++ ep_regs = core_if->dev_if->in_ep_regs[epnum]; ++ ++ len = ep->dwc_ep.xfer_len - ep->dwc_ep.xfer_count; ++ ++ if (len > ep->dwc_ep.maxpacket) { ++ len = ep->dwc_ep.maxpacket; ++ } ++ ++ dwords = (len + 3) / 4; ++ ++ /* While there is space in the queue and space in the FIFO and ++ * More data to tranfer, Write packets to the Tx FIFO */ ++ txstatus.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dtxfsts); ++ DWC_DEBUGPL(DBG_PCDV, "b4 dtxfsts[%d]=0x%08x\n", epnum, txstatus.d32); ++ ++ while (txstatus.b.txfspcavail > dwords && ++ ep->dwc_ep.xfer_count < ep->dwc_ep.xfer_len && ++ ep->dwc_ep.xfer_len != 0) { ++ /* Write the FIFO */ ++ dwc_otg_ep_write_packet(core_if, &ep->dwc_ep, 0); ++ ++ len = ep->dwc_ep.xfer_len - ep->dwc_ep.xfer_count; ++ if (len > ep->dwc_ep.maxpacket) { ++ len = ep->dwc_ep.maxpacket; ++ } ++ ++ dwords = (len + 3) / 4; ++ txstatus.d32 = ++ DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dtxfsts); ++ DWC_DEBUGPL(DBG_PCDV, "dtxfsts[%d]=0x%08x\n", epnum, ++ txstatus.d32); ++ } ++ ++ DWC_DEBUGPL(DBG_PCDV, "b4 dtxfsts[%d]=0x%08x\n", epnum, ++ DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dtxfsts)); ++ ++ return 1; ++} ++ ++/** ++ * This function is called when the Device is disconnected. It stops ++ * any active requests and informs the Gadget driver of the ++ * disconnect. ++ */ ++void dwc_otg_pcd_stop(dwc_otg_pcd_t * pcd) ++{ ++ int i, num_in_eps, num_out_eps; ++ dwc_otg_pcd_ep_t *ep; ++ ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ DWC_SPINLOCK(pcd->lock); ++ ++ num_in_eps = GET_CORE_IF(pcd)->dev_if->num_in_eps; ++ num_out_eps = GET_CORE_IF(pcd)->dev_if->num_out_eps; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s() \n", __func__); ++ /* don't disconnect drivers more than once */ ++ if (pcd->ep0state == EP0_DISCONNECT) { ++ DWC_DEBUGPL(DBG_ANY, "%s() Already Disconnected\n", __func__); ++ DWC_SPINUNLOCK(pcd->lock); ++ return; ++ } ++ pcd->ep0state = EP0_DISCONNECT; ++ ++ /* Reset the OTG state. */ ++ dwc_otg_pcd_update_otg(pcd, 1); ++ ++ /* Disable the NP Tx Fifo Empty Interrupt. */ ++ intr_mask.b.nptxfempty = 1; ++ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk, ++ intr_mask.d32, 0); ++ ++ /* Flush the FIFOs */ ++ /**@todo NGS Flush Periodic FIFOs */ ++ dwc_otg_flush_tx_fifo(GET_CORE_IF(pcd), 0x10); ++ dwc_otg_flush_rx_fifo(GET_CORE_IF(pcd)); ++ ++ /* prevent new request submissions, kill any outstanding requests */ ++ ep = &pcd->ep0; ++ dwc_otg_request_nuke(ep); ++ /* prevent new request submissions, kill any outstanding requests */ ++ for (i = 0; i < num_in_eps; i++) { ++ dwc_otg_pcd_ep_t *ep = &pcd->in_ep[i]; ++ dwc_otg_request_nuke(ep); ++ } ++ /* prevent new request submissions, kill any outstanding requests */ ++ for (i = 0; i < num_out_eps; i++) { ++ dwc_otg_pcd_ep_t *ep = &pcd->out_ep[i]; ++ dwc_otg_request_nuke(ep); ++ } ++ ++ /* report disconnect; the driver is already quiesced */ ++ if (pcd->fops->disconnect) { ++ DWC_SPINUNLOCK(pcd->lock); ++ pcd->fops->disconnect(pcd); ++ DWC_SPINLOCK(pcd->lock); ++ } ++ DWC_SPINUNLOCK(pcd->lock); ++} ++ ++/** ++ * This interrupt indicates that ... ++ */ ++int32_t dwc_otg_pcd_handle_i2c_intr(dwc_otg_pcd_t * pcd) ++{ ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ gintsts_data_t gintsts; ++ ++ DWC_PRINTF("INTERRUPT Handler not implemented for %s\n", "i2cintr"); ++ intr_mask.b.i2cintr = 1; ++ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk, ++ intr_mask.d32, 0); ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.i2cintr = 1; ++ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts, ++ gintsts.d32); ++ return 1; ++} ++ ++/** ++ * This interrupt indicates that ... ++ */ ++int32_t dwc_otg_pcd_handle_early_suspend_intr(dwc_otg_pcd_t * pcd) ++{ ++ gintsts_data_t gintsts; ++#if defined(VERBOSE) ++ DWC_PRINTF("Early Suspend Detected\n"); ++#endif ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.erlysuspend = 1; ++ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts, ++ gintsts.d32); ++ return 1; ++} ++ ++/** ++ * This function configures EPO to receive SETUP packets. ++ * ++ * @todo NGS: Update the comments from the HW FS. ++ * ++ * -# Program the following fields in the endpoint specific registers ++ * for Control OUT EP 0, in order to receive a setup packet ++ * - DOEPTSIZ0.Packet Count = 3 (To receive up to 3 back to back ++ * setup packets) ++ * - DOEPTSIZE0.Transfer Size = 24 Bytes (To receive up to 3 back ++ * to back setup packets) ++ * - In DMA mode, DOEPDMA0 Register with a memory address to ++ * store any setup packets received ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param pcd Programming view of the PCD. ++ */ ++static inline void ep0_out_start(dwc_otg_core_if_t * core_if, ++ dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ deptsiz0_data_t doeptsize0 = {.d32 = 0 }; ++ dwc_otg_dev_dma_desc_t *dma_desc; ++ depctl_data_t doepctl = {.d32 = 0 }; ++ ++#ifdef VERBOSE ++ DWC_DEBUGPL(DBG_PCDV, "%s() doepctl0=%0x\n", __func__, ++ DWC_READ_REG32(&dev_if->out_ep_regs[0]->doepctl)); ++#endif ++ if (core_if->snpsid >= OTG_CORE_REV_3_00a) { ++ doepctl.d32 = DWC_READ_REG32(&dev_if->out_ep_regs[0]->doepctl); ++ if (doepctl.b.epena) { ++ return; ++ } ++ } ++ ++ doeptsize0.b.supcnt = 3; ++ doeptsize0.b.pktcnt = 1; ++ doeptsize0.b.xfersize = 8 * 3; ++ ++ if (core_if->dma_enable) { ++ if (!core_if->dma_desc_enable) { ++ /** put here as for Hermes mode deptisz register should not be written */ ++ DWC_WRITE_REG32(&dev_if->out_ep_regs[0]->doeptsiz, ++ doeptsize0.d32); ++ ++ /** @todo dma needs to handle multiple setup packets (up to 3) */ ++ DWC_WRITE_REG32(&dev_if->out_ep_regs[0]->doepdma, ++ pcd->setup_pkt_dma_handle); ++ } else { ++ dev_if->setup_desc_index = ++ (dev_if->setup_desc_index + 1) & 1; ++ dma_desc = ++ dev_if->setup_desc_addr[dev_if->setup_desc_index]; ++ ++ /** DMA Descriptor Setup */ ++ dma_desc->status.b.bs = BS_HOST_BUSY; ++ if (core_if->snpsid >= OTG_CORE_REV_3_00a) { ++ dma_desc->status.b.sr = 0; ++ dma_desc->status.b.mtrf = 0; ++ } ++ dma_desc->status.b.l = 1; ++ dma_desc->status.b.ioc = 1; ++ dma_desc->status.b.bytes = pcd->ep0.dwc_ep.maxpacket; ++ dma_desc->buf = pcd->setup_pkt_dma_handle; ++ dma_desc->status.b.sts = 0; ++ dma_desc->status.b.bs = BS_HOST_READY; ++ ++ /** DOEPDMA0 Register write */ ++ DWC_WRITE_REG32(&dev_if->out_ep_regs[0]->doepdma, ++ dev_if->dma_setup_desc_addr ++ [dev_if->setup_desc_index]); ++ } ++ ++ } else { ++ /** put here as for Hermes mode deptisz register should not be written */ ++ DWC_WRITE_REG32(&dev_if->out_ep_regs[0]->doeptsiz, ++ doeptsize0.d32); ++ } ++ ++ /** DOEPCTL0 Register write cnak will be set after setup interrupt */ ++ doepctl.d32 = 0; ++ doepctl.b.epena = 1; ++ if (core_if->snpsid <= OTG_CORE_REV_2_94a) { ++ doepctl.b.cnak = 1; ++ DWC_WRITE_REG32(&dev_if->out_ep_regs[0]->doepctl, doepctl.d32); ++ } else { ++ DWC_MODIFY_REG32(&dev_if->out_ep_regs[0]->doepctl, 0, doepctl.d32); ++ } ++ ++#ifdef VERBOSE ++ DWC_DEBUGPL(DBG_PCDV, "doepctl0=%0x\n", ++ DWC_READ_REG32(&dev_if->out_ep_regs[0]->doepctl)); ++ DWC_DEBUGPL(DBG_PCDV, "diepctl0=%0x\n", ++ DWC_READ_REG32(&dev_if->in_ep_regs[0]->diepctl)); ++#endif ++} ++ ++/** ++ * This interrupt occurs when a USB Reset is detected. When the USB ++ * Reset Interrupt occurs the device state is set to DEFAULT and the ++ * EP0 state is set to IDLE. ++ * -# Set the NAK bit for all OUT endpoints (DOEPCTLn.SNAK = 1) ++ * -# Unmask the following interrupt bits ++ * - DAINTMSK.INEP0 = 1 (Control 0 IN endpoint) ++ * - DAINTMSK.OUTEP0 = 1 (Control 0 OUT endpoint) ++ * - DOEPMSK.SETUP = 1 ++ * - DOEPMSK.XferCompl = 1 ++ * - DIEPMSK.XferCompl = 1 ++ * - DIEPMSK.TimeOut = 1 ++ * -# Program the following fields in the endpoint specific registers ++ * for Control OUT EP 0, in order to receive a setup packet ++ * - DOEPTSIZ0.Packet Count = 3 (To receive up to 3 back to back ++ * setup packets) ++ * - DOEPTSIZE0.Transfer Size = 24 Bytes (To receive up to 3 back ++ * to back setup packets) ++ * - In DMA mode, DOEPDMA0 Register with a memory address to ++ * store any setup packets received ++ * At this point, all the required initialization, except for enabling ++ * the control 0 OUT endpoint is done, for receiving SETUP packets. ++ */ ++int32_t dwc_otg_pcd_handle_usb_reset_intr(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ depctl_data_t doepctl = {.d32 = 0 }; ++ depctl_data_t diepctl = {.d32 = 0 }; ++ daint_data_t daintmsk = {.d32 = 0 }; ++ doepmsk_data_t doepmsk = {.d32 = 0 }; ++ diepmsk_data_t diepmsk = {.d32 = 0 }; ++ dcfg_data_t dcfg = {.d32 = 0 }; ++ grstctl_t resetctl = {.d32 = 0 }; ++ dctl_data_t dctl = {.d32 = 0 }; ++ int i = 0; ++ gintsts_data_t gintsts; ++ pcgcctl_data_t power = {.d32 = 0 }; ++ ++ power.d32 = DWC_READ_REG32(core_if->pcgcctl); ++ if (power.b.stoppclk) { ++ power.d32 = 0; ++ power.b.stoppclk = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, power.d32, 0); ++ ++ power.b.pwrclmp = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, power.d32, 0); ++ ++ power.b.rstpdwnmodule = 1; ++ DWC_MODIFY_REG32(core_if->pcgcctl, power.d32, 0); ++ } ++ ++ core_if->lx_state = DWC_OTG_L0; ++ ++ DWC_PRINTF("USB RESET\n"); ++#ifdef DWC_EN_ISOC ++ for (i = 1; i < 16; ++i) { ++ dwc_otg_pcd_ep_t *ep; ++ dwc_ep_t *dwc_ep; ++ ep = get_in_ep(pcd, i); ++ if (ep != 0) { ++ dwc_ep = &ep->dwc_ep; ++ dwc_ep->next_frame = 0xffffffff; ++ } ++ } ++#endif /* DWC_EN_ISOC */ ++ ++ /* reset the HNP settings */ ++ dwc_otg_pcd_update_otg(pcd, 1); ++ ++ /* Clear the Remote Wakeup Signalling */ ++ dctl.b.rmtwkupsig = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32, 0); ++ ++ /* Set NAK for all OUT EPs */ ++ doepctl.b.snak = 1; ++ for (i = 0; i <= dev_if->num_out_eps; i++) { ++ DWC_WRITE_REG32(&dev_if->out_ep_regs[i]->doepctl, doepctl.d32); ++ } ++ ++ /* Flush the NP Tx FIFO */ ++ dwc_otg_flush_tx_fifo(core_if, 0x10); ++ /* Flush the Learning Queue */ ++ resetctl.b.intknqflsh = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->grstctl, resetctl.d32); ++ ++ if (!core_if->core_params->en_multiple_tx_fifo && core_if->dma_enable) { ++ core_if->start_predict = 0; ++ for (i = 0; i<= core_if->dev_if->num_in_eps; ++i) { ++ core_if->nextep_seq[i] = 0xff; // 0xff - EP not active ++ } ++ core_if->nextep_seq[0] = 0; ++ core_if->first_in_nextep_seq = 0; ++ diepctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[0]->diepctl); ++ diepctl.b.nextep = 0; ++ DWC_WRITE_REG32(&dev_if->in_ep_regs[0]->diepctl, diepctl.d32); ++ ++ /* Update IN Endpoint Mismatch Count by active IN NP EP count + 1 */ ++ dcfg.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dcfg); ++ dcfg.b.epmscnt = 2; ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->dcfg, dcfg.d32); ++ ++ DWC_DEBUGPL(DBG_PCDV, ++ "%s first_in_nextep_seq= %2d; nextep_seq[]:\n", ++ __func__, core_if->first_in_nextep_seq); ++ for (i=0; i <= core_if->dev_if->num_in_eps; i++) { ++ DWC_DEBUGPL(DBG_PCDV, "%2d\n", core_if->nextep_seq[i]); ++ } ++ } ++ ++ if (core_if->multiproc_int_enable) { ++ daintmsk.b.inep0 = 1; ++ daintmsk.b.outep0 = 1; ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->deachintmsk, ++ daintmsk.d32); ++ ++ doepmsk.b.setup = 1; ++ doepmsk.b.xfercompl = 1; ++ doepmsk.b.ahberr = 1; ++ doepmsk.b.epdisabled = 1; ++ ++ if ((core_if->dma_desc_enable) || ++ (core_if->dma_enable ++ && core_if->snpsid >= OTG_CORE_REV_3_00a)) { ++ doepmsk.b.stsphsercvd = 1; ++ } ++ if (core_if->dma_desc_enable) ++ doepmsk.b.bna = 1; ++/* ++ doepmsk.b.babble = 1; ++ doepmsk.b.nyet = 1; ++ ++ if (core_if->dma_enable) { ++ doepmsk.b.nak = 1; ++ } ++*/ ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->doepeachintmsk[0], ++ doepmsk.d32); ++ ++ diepmsk.b.xfercompl = 1; ++ diepmsk.b.timeout = 1; ++ diepmsk.b.epdisabled = 1; ++ diepmsk.b.ahberr = 1; ++ diepmsk.b.intknepmis = 1; ++ if (!core_if->en_multiple_tx_fifo && core_if->dma_enable) ++ diepmsk.b.intknepmis = 0; ++ ++/* if (core_if->dma_desc_enable) { ++ diepmsk.b.bna = 1; ++ } ++*/ ++/* ++ if (core_if->dma_enable) { ++ diepmsk.b.nak = 1; ++ } ++*/ ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->diepeachintmsk[0], ++ diepmsk.d32); ++ } else { ++ daintmsk.b.inep0 = 1; ++ daintmsk.b.outep0 = 1; ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->daintmsk, ++ daintmsk.d32); ++ ++ doepmsk.b.setup = 1; ++ doepmsk.b.xfercompl = 1; ++ doepmsk.b.ahberr = 1; ++ doepmsk.b.epdisabled = 1; ++ ++ if ((core_if->dma_desc_enable) || ++ (core_if->dma_enable ++ && core_if->snpsid >= OTG_CORE_REV_3_00a)) { ++ doepmsk.b.stsphsercvd = 1; ++ } ++ if (core_if->dma_desc_enable) ++ doepmsk.b.bna = 1; ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->doepmsk, doepmsk.d32); ++ ++ diepmsk.b.xfercompl = 1; ++ diepmsk.b.timeout = 1; ++ diepmsk.b.epdisabled = 1; ++ diepmsk.b.ahberr = 1; ++ if (!core_if->en_multiple_tx_fifo && core_if->dma_enable) ++ diepmsk.b.intknepmis = 0; ++/* ++ if (core_if->dma_desc_enable) { ++ diepmsk.b.bna = 1; ++ } ++*/ ++ ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->diepmsk, diepmsk.d32); ++ } ++ ++ /* Reset Device Address */ ++ dcfg.d32 = DWC_READ_REG32(&dev_if->dev_global_regs->dcfg); ++ dcfg.b.devaddr = 0; ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->dcfg, dcfg.d32); ++ ++ /* setup EP0 to receive SETUP packets */ ++ if (core_if->snpsid <= OTG_CORE_REV_2_94a) ++ ep0_out_start(core_if, pcd); ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.usbreset = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ ++ return 1; ++} ++ ++/** ++ * Get the device speed from the device status register and convert it ++ * to USB speed constant. ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ */ ++static int get_device_speed(dwc_otg_core_if_t * core_if) ++{ ++ dsts_data_t dsts; ++ int speed = 0; ++ dsts.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dsts); ++ ++ switch (dsts.b.enumspd) { ++ case DWC_DSTS_ENUMSPD_HS_PHY_30MHZ_OR_60MHZ: ++ speed = USB_SPEED_HIGH; ++ break; ++ case DWC_DSTS_ENUMSPD_FS_PHY_30MHZ_OR_60MHZ: ++ case DWC_DSTS_ENUMSPD_FS_PHY_48MHZ: ++ speed = USB_SPEED_FULL; ++ break; ++ ++ case DWC_DSTS_ENUMSPD_LS_PHY_6MHZ: ++ speed = USB_SPEED_LOW; ++ break; ++ } ++ ++ return speed; ++} ++ ++/** ++ * Read the device status register and set the device speed in the ++ * data structure. ++ * Set up EP0 to receive SETUP packets by calling dwc_ep0_activate. ++ */ ++int32_t dwc_otg_pcd_handle_enum_done_intr(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0; ++ gintsts_data_t gintsts; ++ gusbcfg_data_t gusbcfg; ++ dwc_otg_core_global_regs_t *global_regs = ++ GET_CORE_IF(pcd)->core_global_regs; ++ uint8_t utmi16b, utmi8b; ++ int speed; ++ DWC_DEBUGPL(DBG_PCD, "SPEED ENUM\n"); ++ ++ if (GET_CORE_IF(pcd)->snpsid >= OTG_CORE_REV_2_60a) { ++ utmi16b = 6; //vahrama old value was 6; ++ utmi8b = 9; ++ } else { ++ utmi16b = 4; ++ utmi8b = 8; ++ } ++ dwc_otg_ep0_activate(GET_CORE_IF(pcd), &ep0->dwc_ep); ++ if (GET_CORE_IF(pcd)->snpsid >= OTG_CORE_REV_3_00a) { ++ ep0_out_start(GET_CORE_IF(pcd), pcd); ++ } ++ ++#ifdef DEBUG_EP0 ++ print_ep0_state(pcd); ++#endif ++ ++ if (pcd->ep0state == EP0_DISCONNECT) { ++ pcd->ep0state = EP0_IDLE; ++ } else if (pcd->ep0state == EP0_STALL) { ++ pcd->ep0state = EP0_IDLE; ++ } ++ ++ pcd->ep0state = EP0_IDLE; ++ ++ ep0->stopped = 0; ++ ++ speed = get_device_speed(GET_CORE_IF(pcd)); ++ pcd->fops->connect(pcd, speed); ++ ++ /* Set USB turnaround time based on device speed and PHY interface. */ ++ gusbcfg.d32 = DWC_READ_REG32(&global_regs->gusbcfg); ++ if (speed == USB_SPEED_HIGH) { ++ if (GET_CORE_IF(pcd)->hwcfg2.b.hs_phy_type == ++ DWC_HWCFG2_HS_PHY_TYPE_ULPI) { ++ /* ULPI interface */ ++ gusbcfg.b.usbtrdtim = 9; ++ } ++ if (GET_CORE_IF(pcd)->hwcfg2.b.hs_phy_type == ++ DWC_HWCFG2_HS_PHY_TYPE_UTMI) { ++ /* UTMI+ interface */ ++ if (GET_CORE_IF(pcd)->hwcfg4.b.utmi_phy_data_width == 0) { ++ gusbcfg.b.usbtrdtim = utmi8b; ++ } else if (GET_CORE_IF(pcd)->hwcfg4. ++ b.utmi_phy_data_width == 1) { ++ gusbcfg.b.usbtrdtim = utmi16b; ++ } else if (GET_CORE_IF(pcd)-> ++ core_params->phy_utmi_width == 8) { ++ gusbcfg.b.usbtrdtim = utmi8b; ++ } else { ++ gusbcfg.b.usbtrdtim = utmi16b; ++ } ++ } ++ if (GET_CORE_IF(pcd)->hwcfg2.b.hs_phy_type == ++ DWC_HWCFG2_HS_PHY_TYPE_UTMI_ULPI) { ++ /* UTMI+ OR ULPI interface */ ++ if (gusbcfg.b.ulpi_utmi_sel == 1) { ++ /* ULPI interface */ ++ gusbcfg.b.usbtrdtim = 9; ++ } else { ++ /* UTMI+ interface */ ++ if (GET_CORE_IF(pcd)-> ++ core_params->phy_utmi_width == 16) { ++ gusbcfg.b.usbtrdtim = utmi16b; ++ } else { ++ gusbcfg.b.usbtrdtim = utmi8b; ++ } ++ } ++ } ++ } else { ++ /* Full or low speed */ ++ gusbcfg.b.usbtrdtim = 9; ++ } ++ DWC_WRITE_REG32(&global_regs->gusbcfg, gusbcfg.d32); ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.enumdone = 1; ++ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts, ++ gintsts.d32); ++ return 1; ++} ++ ++/** ++ * This interrupt indicates that the ISO OUT Packet was dropped due to ++ * Rx FIFO full or Rx Status Queue Full. If this interrupt occurs ++ * read all the data from the Rx FIFO. ++ */ ++int32_t dwc_otg_pcd_handle_isoc_out_packet_dropped_intr(dwc_otg_pcd_t * pcd) ++{ ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ gintsts_data_t gintsts; ++ ++ DWC_WARN("INTERRUPT Handler not implemented for %s\n", ++ "ISOC Out Dropped"); ++ ++ intr_mask.b.isooutdrop = 1; ++ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk, ++ intr_mask.d32, 0); ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.isooutdrop = 1; ++ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts, ++ gintsts.d32); ++ ++ return 1; ++} ++ ++/** ++ * This interrupt indicates the end of the portion of the micro-frame ++ * for periodic transactions. If there is a periodic transaction for ++ * the next frame, load the packets into the EP periodic Tx FIFO. ++ */ ++int32_t dwc_otg_pcd_handle_end_periodic_frame_intr(dwc_otg_pcd_t * pcd) ++{ ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ gintsts_data_t gintsts; ++ DWC_PRINTF("INTERRUPT Handler not implemented for %s\n", "EOP"); ++ ++ intr_mask.b.eopframe = 1; ++ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk, ++ intr_mask.d32, 0); ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.eopframe = 1; ++ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts, ++ gintsts.d32); ++ ++ return 1; ++} ++ ++/** ++ * This interrupt indicates that EP of the packet on the top of the ++ * non-periodic Tx FIFO does not match EP of the IN Token received. ++ * ++ * The "Device IN Token Queue" Registers are read to determine the ++ * order the IN Tokens have been received. The non-periodic Tx FIFO ++ * is flushed, so it can be reloaded in the order seen in the IN Token ++ * Queue. ++ */ ++int32_t dwc_otg_pcd_handle_ep_mismatch_intr(dwc_otg_pcd_t * pcd) ++{ ++ gintsts_data_t gintsts; ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dctl_data_t dctl; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ if (!core_if->en_multiple_tx_fifo && core_if->dma_enable) { ++ core_if->start_predict = 1; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, core_if); ++ ++ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts); ++ if (!gintsts.b.ginnakeff) { ++ /* Disable EP Mismatch interrupt */ ++ intr_mask.d32 = 0; ++ intr_mask.b.epmismatch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, intr_mask.d32, 0); ++ /* Enable the Global IN NAK Effective Interrupt */ ++ intr_mask.d32 = 0; ++ intr_mask.b.ginnakeff = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, 0, intr_mask.d32); ++ /* Set the global non-periodic IN NAK handshake */ ++ dctl.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dctl); ++ dctl.b.sgnpinnak = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32); ++ } else { ++ DWC_PRINTF("gintsts.b.ginnakeff = 1! dctl.b.sgnpinnak not set\n"); ++ } ++ /* Disabling of all EP's will be done in dwc_otg_pcd_handle_in_nak_effective() ++ * handler after Global IN NAK Effective interrupt will be asserted */ ++ } ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.epmismatch = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ ++ return 1; ++} ++ ++/** ++ * This interrupt is valid only in DMA mode. This interrupt indicates that the ++ * core has stopped fetching data for IN endpoints due to the unavailability of ++ * TxFIFO space or Request Queue space. This interrupt is used by the ++ * application for an endpoint mismatch algorithm. ++ * ++ * @param pcd The PCD ++ */ ++int32_t dwc_otg_pcd_handle_ep_fetsusp_intr(dwc_otg_pcd_t * pcd) ++{ ++ gintsts_data_t gintsts; ++ gintmsk_data_t gintmsk_data; ++ dctl_data_t dctl; ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, core_if); ++ ++ /* Clear the global non-periodic IN NAK handshake */ ++ dctl.d32 = 0; ++ dctl.b.cgnpinnak = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32, dctl.d32); ++ ++ /* Mask GINTSTS.FETSUSP interrupt */ ++ gintmsk_data.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintmsk); ++ gintmsk_data.b.fetsusp = 0; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, gintmsk_data.d32); ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.fetsusp = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintsts, gintsts.d32); ++ ++ return 1; ++} ++/** ++ * This funcion stalls EP0. ++ */ ++static inline void ep0_do_stall(dwc_otg_pcd_t * pcd, const int err_val) ++{ ++ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0; ++ usb_device_request_t *ctrl = &pcd->setup_pkt->req; ++ DWC_WARN("req %02x.%02x protocol STALL; err %d\n", ++ ctrl->bmRequestType, ctrl->bRequest, err_val); ++ ++ ep0->dwc_ep.is_in = 1; ++ dwc_otg_ep_set_stall(GET_CORE_IF(pcd), &ep0->dwc_ep); ++ pcd->ep0.stopped = 1; ++ pcd->ep0state = EP0_IDLE; ++ ep0_out_start(GET_CORE_IF(pcd), pcd); ++} ++ ++/** ++ * This functions delegates the setup command to the gadget driver. ++ */ ++static inline void do_gadget_setup(dwc_otg_pcd_t * pcd, ++ usb_device_request_t * ctrl) ++{ ++ int ret = 0; ++ DWC_SPINUNLOCK(pcd->lock); ++ ret = pcd->fops->setup(pcd, (uint8_t *) ctrl); ++ DWC_SPINLOCK(pcd->lock); ++ if (ret < 0) { ++ ep0_do_stall(pcd, ret); ++ } ++ ++ /** @todo This is a g_file_storage gadget driver specific ++ * workaround: a DELAYED_STATUS result from the fsg_setup ++ * routine will result in the gadget queueing a EP0 IN status ++ * phase for a two-stage control transfer. Exactly the same as ++ * a SET_CONFIGURATION/SET_INTERFACE except that this is a class ++ * specific request. Need a generic way to know when the gadget ++ * driver will queue the status phase. Can we assume when we ++ * call the gadget driver setup() function that it will always ++ * queue and require the following flag? Need to look into ++ * this. ++ */ ++ ++ if (ret == 256 + 999) { ++ pcd->request_config = 1; ++ } ++} ++ ++#ifdef DWC_UTE_CFI ++/** ++ * This functions delegates the CFI setup commands to the gadget driver. ++ * This function will return a negative value to indicate a failure. ++ */ ++static inline int cfi_gadget_setup(dwc_otg_pcd_t * pcd, ++ struct cfi_usb_ctrlrequest *ctrl_req) ++{ ++ int ret = 0; ++ ++ if (pcd->fops && pcd->fops->cfi_setup) { ++ DWC_SPINUNLOCK(pcd->lock); ++ ret = pcd->fops->cfi_setup(pcd, ctrl_req); ++ DWC_SPINLOCK(pcd->lock); ++ if (ret < 0) { ++ ep0_do_stall(pcd, ret); ++ return ret; ++ } ++ } ++ ++ return ret; ++} ++#endif ++ ++/** ++ * This function starts the Zero-Length Packet for the IN status phase ++ * of a 2 stage control transfer. ++ */ ++static inline void do_setup_in_status_phase(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0; ++ if (pcd->ep0state == EP0_STALL) { ++ return; ++ } ++ ++ pcd->ep0state = EP0_IN_STATUS_PHASE; ++ ++ /* Prepare for more SETUP Packets */ ++ DWC_DEBUGPL(DBG_PCD, "EP0 IN ZLP\n"); ++ if ((GET_CORE_IF(pcd)->snpsid >= OTG_CORE_REV_3_00a) ++ && (pcd->core_if->dma_desc_enable) ++ && (ep0->dwc_ep.xfer_count < ep0->dwc_ep.total_len)) { ++ DWC_DEBUGPL(DBG_PCDV, ++ "Data terminated wait next packet in out_desc_addr\n"); ++ pcd->backup_buf = phys_to_virt(ep0->dwc_ep.dma_addr); ++ pcd->data_terminated = 1; ++ } ++ ep0->dwc_ep.xfer_len = 0; ++ ep0->dwc_ep.xfer_count = 0; ++ ep0->dwc_ep.is_in = 1; ++ ep0->dwc_ep.dma_addr = pcd->setup_pkt_dma_handle; ++ dwc_otg_ep0_start_transfer(GET_CORE_IF(pcd), &ep0->dwc_ep); ++ ++ /* Prepare for more SETUP Packets */ ++ //ep0_out_start(GET_CORE_IF(pcd), pcd); ++} ++ ++/** ++ * This function starts the Zero-Length Packet for the OUT status phase ++ * of a 2 stage control transfer. ++ */ ++static inline void do_setup_out_status_phase(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0; ++ if (pcd->ep0state == EP0_STALL) { ++ DWC_DEBUGPL(DBG_PCD, "EP0 STALLED\n"); ++ return; ++ } ++ pcd->ep0state = EP0_OUT_STATUS_PHASE; ++ ++ DWC_DEBUGPL(DBG_PCD, "EP0 OUT ZLP\n"); ++ ep0->dwc_ep.xfer_len = 0; ++ ep0->dwc_ep.xfer_count = 0; ++ ep0->dwc_ep.is_in = 0; ++ ep0->dwc_ep.dma_addr = pcd->setup_pkt_dma_handle; ++ dwc_otg_ep0_start_transfer(GET_CORE_IF(pcd), &ep0->dwc_ep); ++ ++ /* Prepare for more SETUP Packets */ ++ if (GET_CORE_IF(pcd)->dma_enable == 0) { ++ ep0_out_start(GET_CORE_IF(pcd), pcd); ++ } ++} ++ ++/** ++ * Clear the EP halt (STALL) and if pending requests start the ++ * transfer. ++ */ ++static inline void pcd_clear_halt(dwc_otg_pcd_t * pcd, dwc_otg_pcd_ep_t * ep) ++{ ++ if (ep->dwc_ep.stall_clear_flag == 0) ++ dwc_otg_ep_clear_stall(GET_CORE_IF(pcd), &ep->dwc_ep); ++ ++ /* Reactive the EP */ ++ dwc_otg_ep_activate(GET_CORE_IF(pcd), &ep->dwc_ep); ++ if (ep->stopped) { ++ ep->stopped = 0; ++ /* If there is a request in the EP queue start it */ ++ ++ /** @todo FIXME: this causes an EP mismatch in DMA mode. ++ * epmismatch not yet implemented. */ ++ ++ /* ++ * Above fixme is solved by implmenting a tasklet to call the ++ * start_next_request(), outside of interrupt context at some ++ * time after the current time, after a clear-halt setup packet. ++ * Still need to implement ep mismatch in the future if a gadget ++ * ever uses more than one endpoint at once ++ */ ++ ep->queue_sof = 1; ++ DWC_TASK_SCHEDULE(pcd->start_xfer_tasklet); ++ } ++ /* Start Control Status Phase */ ++ do_setup_in_status_phase(pcd); ++} ++ ++/** ++ * This function is called when the SET_FEATURE TEST_MODE Setup packet ++ * is sent from the host. The Device Control register is written with ++ * the Test Mode bits set to the specified Test Mode. This is done as ++ * a tasklet so that the "Status" phase of the control transfer ++ * completes before transmitting the TEST packets. ++ * ++ * @todo This has not been tested since the tasklet struct was put ++ * into the PCD struct! ++ * ++ */ ++void do_test_mode(void *data) ++{ ++ dctl_data_t dctl; ++ dwc_otg_pcd_t *pcd = (dwc_otg_pcd_t *) data; ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ int test_mode = pcd->test_mode; ++ ++// DWC_WARN("%s() has not been tested since being rewritten!\n", __func__); ++ ++ dctl.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dctl); ++ switch (test_mode) { ++ case 1: // TEST_J ++ dctl.b.tstctl = 1; ++ break; ++ ++ case 2: // TEST_K ++ dctl.b.tstctl = 2; ++ break; ++ ++ case 3: // TEST_SE0_NAK ++ dctl.b.tstctl = 3; ++ break; ++ ++ case 4: // TEST_PACKET ++ dctl.b.tstctl = 4; ++ break; ++ ++ case 5: // TEST_FORCE_ENABLE ++ dctl.b.tstctl = 5; ++ break; ++ } ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32); ++} ++ ++/** ++ * This function process the GET_STATUS Setup Commands. ++ */ ++static inline void do_get_status(dwc_otg_pcd_t * pcd) ++{ ++ usb_device_request_t ctrl = pcd->setup_pkt->req; ++ dwc_otg_pcd_ep_t *ep; ++ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0; ++ uint16_t *status = pcd->status_buf; ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ ++#ifdef DEBUG_EP0 ++ DWC_DEBUGPL(DBG_PCD, ++ "GET_STATUS %02x.%02x v%04x i%04x l%04x\n", ++ ctrl.bmRequestType, ctrl.bRequest, ++ UGETW(ctrl.wValue), UGETW(ctrl.wIndex), ++ UGETW(ctrl.wLength)); ++#endif ++ ++ switch (UT_GET_RECIPIENT(ctrl.bmRequestType)) { ++ case UT_DEVICE: ++ if(UGETW(ctrl.wIndex) == 0xF000) { /* OTG Status selector */ ++ DWC_PRINTF("wIndex - %d\n", UGETW(ctrl.wIndex)); ++ DWC_PRINTF("OTG VERSION - %d\n", core_if->otg_ver); ++ DWC_PRINTF("OTG CAP - %d, %d\n", ++ core_if->core_params->otg_cap, ++ DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE); ++ if (core_if->otg_ver == 1 ++ && core_if->core_params->otg_cap == ++ DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE) { ++ uint8_t *otgsts = (uint8_t*)pcd->status_buf; ++ *otgsts = (core_if->otg_sts & 0x1); ++ pcd->ep0_pending = 1; ++ ep0->dwc_ep.start_xfer_buff = ++ (uint8_t *) otgsts; ++ ep0->dwc_ep.xfer_buff = (uint8_t *) otgsts; ++ ep0->dwc_ep.dma_addr = ++ pcd->status_buf_dma_handle; ++ ep0->dwc_ep.xfer_len = 1; ++ ep0->dwc_ep.xfer_count = 0; ++ ep0->dwc_ep.total_len = ep0->dwc_ep.xfer_len; ++ dwc_otg_ep0_start_transfer(GET_CORE_IF(pcd), ++ &ep0->dwc_ep); ++ return; ++ } else { ++ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED); ++ return; ++ } ++ break; ++ } else { ++ *status = 0x1; /* Self powered */ ++ *status |= pcd->remote_wakeup_enable << 1; ++ break; ++ } ++ case UT_INTERFACE: ++ *status = 0; ++ break; ++ ++ case UT_ENDPOINT: ++ ep = get_ep_by_addr(pcd, UGETW(ctrl.wIndex)); ++ if (ep == 0 || UGETW(ctrl.wLength) > 2) { ++ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED); ++ return; ++ } ++ /** @todo check for EP stall */ ++ *status = ep->stopped; ++ break; ++ } ++ pcd->ep0_pending = 1; ++ ep0->dwc_ep.start_xfer_buff = (uint8_t *) status; ++ ep0->dwc_ep.xfer_buff = (uint8_t *) status; ++ ep0->dwc_ep.dma_addr = pcd->status_buf_dma_handle; ++ ep0->dwc_ep.xfer_len = 2; ++ ep0->dwc_ep.xfer_count = 0; ++ ep0->dwc_ep.total_len = ep0->dwc_ep.xfer_len; ++ dwc_otg_ep0_start_transfer(GET_CORE_IF(pcd), &ep0->dwc_ep); ++} ++ ++/** ++ * This function process the SET_FEATURE Setup Commands. ++ */ ++static inline void do_set_feature(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++ usb_device_request_t ctrl = pcd->setup_pkt->req; ++ dwc_otg_pcd_ep_t *ep = 0; ++ int32_t otg_cap_param = core_if->core_params->otg_cap; ++ gotgctl_data_t gotgctl = {.d32 = 0 }; ++ ++ DWC_DEBUGPL(DBG_PCD, "SET_FEATURE:%02x.%02x v%04x i%04x l%04x\n", ++ ctrl.bmRequestType, ctrl.bRequest, ++ UGETW(ctrl.wValue), UGETW(ctrl.wIndex), ++ UGETW(ctrl.wLength)); ++ DWC_DEBUGPL(DBG_PCD, "otg_cap=%d\n", otg_cap_param); ++ ++ switch (UT_GET_RECIPIENT(ctrl.bmRequestType)) { ++ case UT_DEVICE: ++ switch (UGETW(ctrl.wValue)) { ++ case UF_DEVICE_REMOTE_WAKEUP: ++ pcd->remote_wakeup_enable = 1; ++ break; ++ ++ case UF_TEST_MODE: ++ /* Setup the Test Mode tasklet to do the Test ++ * Packet generation after the SETUP Status ++ * phase has completed. */ ++ ++ /** @todo This has not been tested since the ++ * tasklet struct was put into the PCD ++ * struct! */ ++ pcd->test_mode = UGETW(ctrl.wIndex) >> 8; ++ DWC_TASK_SCHEDULE(pcd->test_mode_tasklet); ++ break; ++ ++ case UF_DEVICE_B_HNP_ENABLE: ++ DWC_DEBUGPL(DBG_PCDV, ++ "SET_FEATURE: USB_DEVICE_B_HNP_ENABLE\n"); ++ ++ /* dev may initiate HNP */ ++ if (otg_cap_param == DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE) { ++ pcd->b_hnp_enable = 1; ++ dwc_otg_pcd_update_otg(pcd, 0); ++ DWC_DEBUGPL(DBG_PCD, "Request B HNP\n"); ++ /**@todo Is the gotgctl.devhnpen cleared ++ * by a USB Reset? */ ++ gotgctl.b.devhnpen = 1; ++ gotgctl.b.hnpreq = 1; ++ DWC_WRITE_REG32(&global_regs->gotgctl, ++ gotgctl.d32); ++ } else { ++ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED); ++ return; ++ } ++ break; ++ ++ case UF_DEVICE_A_HNP_SUPPORT: ++ /* RH port supports HNP */ ++ DWC_DEBUGPL(DBG_PCDV, ++ "SET_FEATURE: USB_DEVICE_A_HNP_SUPPORT\n"); ++ if (otg_cap_param == DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE) { ++ pcd->a_hnp_support = 1; ++ dwc_otg_pcd_update_otg(pcd, 0); ++ } else { ++ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED); ++ return; ++ } ++ break; ++ ++ case UF_DEVICE_A_ALT_HNP_SUPPORT: ++ /* other RH port does */ ++ DWC_DEBUGPL(DBG_PCDV, ++ "SET_FEATURE: USB_DEVICE_A_ALT_HNP_SUPPORT\n"); ++ if (otg_cap_param == DWC_OTG_CAP_PARAM_HNP_SRP_CAPABLE) { ++ pcd->a_alt_hnp_support = 1; ++ dwc_otg_pcd_update_otg(pcd, 0); ++ } else { ++ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED); ++ return; ++ } ++ break; ++ ++ default: ++ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED); ++ return; ++ ++ } ++ do_setup_in_status_phase(pcd); ++ break; ++ ++ case UT_INTERFACE: ++ do_gadget_setup(pcd, &ctrl); ++ break; ++ ++ case UT_ENDPOINT: ++ if (UGETW(ctrl.wValue) == UF_ENDPOINT_HALT) { ++ ep = get_ep_by_addr(pcd, UGETW(ctrl.wIndex)); ++ if (ep == 0) { ++ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED); ++ return; ++ } ++ ep->stopped = 1; ++ dwc_otg_ep_set_stall(core_if, &ep->dwc_ep); ++ } ++ do_setup_in_status_phase(pcd); ++ break; ++ } ++} ++ ++/** ++ * This function process the CLEAR_FEATURE Setup Commands. ++ */ ++static inline void do_clear_feature(dwc_otg_pcd_t * pcd) ++{ ++ usb_device_request_t ctrl = pcd->setup_pkt->req; ++ dwc_otg_pcd_ep_t *ep = 0; ++ ++ DWC_DEBUGPL(DBG_PCD, ++ "CLEAR_FEATURE:%02x.%02x v%04x i%04x l%04x\n", ++ ctrl.bmRequestType, ctrl.bRequest, ++ UGETW(ctrl.wValue), UGETW(ctrl.wIndex), ++ UGETW(ctrl.wLength)); ++ ++ switch (UT_GET_RECIPIENT(ctrl.bmRequestType)) { ++ case UT_DEVICE: ++ switch (UGETW(ctrl.wValue)) { ++ case UF_DEVICE_REMOTE_WAKEUP: ++ pcd->remote_wakeup_enable = 0; ++ break; ++ ++ case UF_TEST_MODE: ++ /** @todo Add CLEAR_FEATURE for TEST modes. */ ++ break; ++ ++ default: ++ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED); ++ return; ++ } ++ do_setup_in_status_phase(pcd); ++ break; ++ ++ case UT_ENDPOINT: ++ ep = get_ep_by_addr(pcd, UGETW(ctrl.wIndex)); ++ if (ep == 0) { ++ ep0_do_stall(pcd, -DWC_E_NOT_SUPPORTED); ++ return; ++ } ++ ++ pcd_clear_halt(pcd, ep); ++ ++ break; ++ } ++} ++ ++/** ++ * This function process the SET_ADDRESS Setup Commands. ++ */ ++static inline void do_set_address(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_dev_if_t *dev_if = GET_CORE_IF(pcd)->dev_if; ++ usb_device_request_t ctrl = pcd->setup_pkt->req; ++ ++ if (ctrl.bmRequestType == UT_DEVICE) { ++ dcfg_data_t dcfg = {.d32 = 0 }; ++ ++#ifdef DEBUG_EP0 ++// DWC_DEBUGPL(DBG_PCDV, "SET_ADDRESS:%d\n", ctrl.wValue); ++#endif ++ dcfg.b.devaddr = UGETW(ctrl.wValue); ++ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dcfg, 0, dcfg.d32); ++ do_setup_in_status_phase(pcd); ++ } ++} ++ ++/** ++ * This function processes SETUP commands. In Linux, the USB Command ++ * processing is done in two places - the first being the PCD and the ++ * second in the Gadget Driver (for example, the File-Backed Storage ++ * Gadget Driver). ++ * ++ *
Parameter NameMeaning
otg_capSpecifies the OTG capabilities. The driver will automatically detect the ++ value for this parameter if none is specified. ++ - 0: HNP and SRP capable (default, if available) ++ - 1: SRP Only capable ++ - 2: No HNP/SRP capable ++
dma_enableSpecifies whether to use slave or DMA mode for accessing the data FIFOs. ++ The driver will automatically detect the value for this parameter if none is ++ specified. ++ - 0: Slave ++ - 1: DMA (default, if available) ++
dma_burst_sizeThe DMA Burst size (applicable only for External DMA Mode). ++ - Values: 1, 4, 8 16, 32, 64, 128, 256 (default 32) ++
speedSpecifies the maximum speed of operation in host and device mode. The ++ actual speed depends on the speed of the attached device and the value of ++ phy_type. ++ - 0: High Speed (default) ++ - 1: Full Speed ++
host_support_fs_ls_low_powerSpecifies whether low power mode is supported when attached to a Full ++ Speed or Low Speed device in host mode. ++ - 0: Don't support low power mode (default) ++ - 1: Support low power mode ++
host_ls_low_power_phy_clkSpecifies the PHY clock rate in low power mode when connected to a Low ++ Speed device in host mode. This parameter is applicable only if ++ HOST_SUPPORT_FS_LS_LOW_POWER is enabled. ++ - 0: 48 MHz (default) ++ - 1: 6 MHz ++
enable_dynamic_fifo Specifies whether FIFOs may be resized by the driver software. ++ - 0: Use cC FIFO size parameters ++ - 1: Allow dynamic FIFO sizing (default) ++
data_fifo_sizeTotal number of 4-byte words in the data FIFO memory. This memory ++ includes the Rx FIFO, non-periodic Tx FIFO, and periodic Tx FIFOs. ++ - Values: 32 to 32768 (default 8192) ++ ++ Note: The total FIFO memory depth in the FPGA configuration is 8192. ++
dev_rx_fifo_sizeNumber of 4-byte words in the Rx FIFO in device mode when dynamic ++ FIFO sizing is enabled. ++ - Values: 16 to 32768 (default 1064) ++
dev_nperio_tx_fifo_sizeNumber of 4-byte words in the non-periodic Tx FIFO in device mode when ++ dynamic FIFO sizing is enabled. ++ - Values: 16 to 32768 (default 1024) ++
dev_perio_tx_fifo_size_n (n = 1 to 15)Number of 4-byte words in each of the periodic Tx FIFOs in device mode ++ when dynamic FIFO sizing is enabled. ++ - Values: 4 to 768 (default 256) ++
host_rx_fifo_sizeNumber of 4-byte words in the Rx FIFO in host mode when dynamic FIFO ++ sizing is enabled. ++ - Values: 16 to 32768 (default 1024) ++
host_nperio_tx_fifo_sizeNumber of 4-byte words in the non-periodic Tx FIFO in host mode when ++ dynamic FIFO sizing is enabled in the core. ++ - Values: 16 to 32768 (default 1024) ++
host_perio_tx_fifo_sizeNumber of 4-byte words in the host periodic Tx FIFO when dynamic FIFO ++ sizing is enabled. ++ - Values: 16 to 32768 (default 1024) ++
max_transfer_sizeThe maximum transfer size supported in bytes. ++ - Values: 2047 to 65,535 (default 65,535) ++
max_packet_countThe maximum number of packets in a transfer. ++ - Values: 15 to 511 (default 511) ++
host_channelsThe number of host channel registers to use. ++ - Values: 1 to 16 (default 12) ++ ++ Note: The FPGA configuration supports a maximum of 12 host channels. ++
dev_endpointsThe number of endpoints in addition to EP0 available for device mode ++ operations. ++ - Values: 1 to 15 (default 6 IN and OUT) ++ ++ Note: The FPGA configuration supports a maximum of 6 IN and OUT endpoints in ++ addition to EP0. ++
phy_typeSpecifies the type of PHY interface to use. By default, the driver will ++ automatically detect the phy_type. ++ - 0: Full Speed ++ - 1: UTMI+ (default, if available) ++ - 2: ULPI ++
phy_utmi_widthSpecifies the UTMI+ Data Width. This parameter is applicable for a ++ phy_type of UTMI+. Also, this parameter is applicable only if the ++ OTG_HSPHY_WIDTH cC parameter was set to "8 and 16 bits", meaning that the ++ core has been configured to work at either data path width. ++ - Values: 8 or 16 bits (default 16) ++
phy_ulpi_ddrSpecifies whether the ULPI operates at double or single data rate. This ++ parameter is only applicable if phy_type is ULPI. ++ - 0: single data rate ULPI interface with 8 bit wide data bus (default) ++ - 1: double data rate ULPI interface with 4 bit wide data bus ++
i2c_enableSpecifies whether to use the I2C interface for full speed PHY. This ++ parameter is only applicable if PHY_TYPE is FS. ++ - 0: Disabled (default) ++ - 1: Enabled ++
ulpi_fs_lsSpecifies whether to use ULPI FS/LS mode only. ++ - 0: Disabled (default) ++ - 1: Enabled ++
ts_dlineSpecifies whether term select D-Line pulsing for all PHYs is enabled. ++ - 0: Disabled (default) ++ - 1: Enabled ++
en_multiple_tx_fifoSpecifies whether dedicatedto tx fifos are enabled for non periodic IN EPs. ++ The driver will automatically detect the value for this parameter if none is ++ specified. ++ - 0: Disabled ++ - 1: Enabled (default, if available) ++
dev_tx_fifo_size_n (n = 1 to 15)Number of 4-byte words in each of the Tx FIFOs in device mode ++ when dynamic FIFO sizing is enabled. ++ - Values: 4 to 768 (default 256) ++
tx_thr_lengthTransmit Threshold length in 32 bit double words ++ - Values: 8 to 128 (default 64) ++
rx_thr_lengthReceive Threshold length in 32 bit double words ++ - Values: 8 to 128 (default 64) ++
thr_ctlSpecifies whether to enable Thresholding for Device mode. Bits 0, 1, 2 of ++ this parmater specifies if thresholding is enabled for non-Iso Tx, Iso Tx and ++ Rx transfers accordingly. ++ The driver will automatically detect the value for this parameter if none is ++ specified. ++ - Values: 0 to 7 (default 0) ++ Bit values indicate: ++ - 0: Thresholding disabled ++ - 1: Thresholding enabled ++
dma_desc_enableSpecifies whether to enable Descriptor DMA mode. ++ The driver will automatically detect the value for this parameter if none is ++ specified. ++ - 0: Descriptor DMA disabled ++ - 1: Descriptor DMA (default, if available) ++
mpi_enableSpecifies whether to enable MPI enhancement mode. ++ The driver will automatically detect the value for this parameter if none is ++ specified. ++ - 0: MPI disabled (default) ++ - 1: MPI enable ++
pti_enableSpecifies whether to enable PTI enhancement support. ++ The driver will automatically detect the value for this parameter if none is ++ specified. ++ - 0: PTI disabled (default) ++ - 1: PTI enable ++
lpm_enableSpecifies whether to enable LPM support. ++ The driver will automatically detect the value for this parameter if none is ++ specified. ++ - 0: LPM disabled ++ - 1: LPM enable (default, if available) ++
ic_usb_capSpecifies whether to enable IC_USB capability. ++ The driver will automatically detect the value for this parameter if none is ++ specified. ++ - 0: IC_USB disabled (default, if available) ++ - 1: IC_USB enable ++
ahb_thr_ratioSpecifies AHB Threshold ratio. ++ - Values: 0 to 3 (default 0) ++
power_downSpecifies Power Down(Hibernation) Mode. ++ The driver will automatically detect the value for this parameter if none is ++ specified. ++ - 0: Power Down disabled (default) ++ - 2: Power Down enabled ++
reload_ctlSpecifies whether dynamic reloading of the HFIR register is allowed during ++ run time. The driver will automatically detect the value for this parameter if ++ none is specified. In case the HFIR value is reloaded when HFIR.RldCtrl == 1'b0 ++ the core might misbehave. ++ - 0: Reload Control disabled (default) ++ - 1: Reload Control enabled ++
dev_out_nakSpecifies whether Device OUT NAK enhancement enabled or no. ++ The driver will automatically detect the value for this parameter if ++ none is specified. This parameter is valid only when OTG_EN_DESC_DMA == 1b1. ++ - 0: The core does not set NAK after Bulk OUT transfer complete (default) ++ - 1: The core sets NAK after Bulk OUT transfer complete ++
cont_on_bnaSpecifies whether Enable Continue on BNA enabled or no. ++ After receiving BNA interrupt the core disables the endpoint,when the ++ endpoint is re-enabled by the application the ++ - 0: Core starts processing from the DOEPDMA descriptor (default) ++ - 1: Core starts processing from the descriptor which received the BNA. ++ This parameter is valid only when OTG_EN_DESC_DMA == 1b1. ++
ahb_singleThis bit when programmed supports SINGLE transfers for remainder data ++ in a transfer for DMA mode of operation. ++ - 0: The remainder data will be sent using INCR burst size (default) ++ - 1: The remainder data will be sent using SINGLE burst size. ++
adp_enableSpecifies whether ADP feature is enabled. ++ The driver will automatically detect the value for this parameter if none is ++ specified. ++ - 0: ADP feature disabled (default) ++ - 1: ADP feature enabled ++
otg_verSpecifies whether OTG is performing as USB OTG Revision 2.0 or Revision 1.3 ++ USB OTG device. ++ - 0: OTG 2.0 support disabled (default) ++ - 1: OTG 2.0 support enabled ++
++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ * ++ *
Command Driver Description
GET_STATUS PCD Command is processed as ++ * defined in chapter 9 of the USB 2.0 Specification chapter 9 ++ *
CLEAR_FEATURE PCD The Device and Endpoint ++ * requests are the ENDPOINT_HALT feature is procesed, all others the ++ * interface requests are ignored.
SET_FEATURE PCD The Device and Endpoint ++ * requests are processed by the PCD. Interface requests are passed ++ * to the Gadget Driver.
SET_ADDRESS PCD Program the DCFG reg, ++ * with device address received
GET_DESCRIPTOR Gadget Driver Return the ++ * requested descriptor
SET_DESCRIPTOR Gadget Driver Optional - ++ * not implemented by any of the existing Gadget Drivers.
SET_CONFIGURATION Gadget Driver Disable ++ * all EPs and enable EPs for new configuration.
GET_CONFIGURATION Gadget Driver Return ++ * the current configuration
SET_INTERFACE Gadget Driver Disable all ++ * EPs and enable EPs for new configuration.
GET_INTERFACE Gadget Driver Return the ++ * current interface.
SYNC_FRAME PCD Display debug ++ * message.
++ * ++ * When the SETUP Phase Done interrupt occurs, the PCD SETUP commands are ++ * processed by pcd_setup. Calling the Function Driver's setup function from ++ * pcd_setup processes the gadget SETUP commands. ++ */ ++static inline void pcd_setup(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ usb_device_request_t ctrl = pcd->setup_pkt->req; ++ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0; ++ ++ deptsiz0_data_t doeptsize0 = {.d32 = 0 }; ++ ++#ifdef DWC_UTE_CFI ++ int retval = 0; ++ struct cfi_usb_ctrlrequest cfi_req; ++#endif ++ ++ doeptsize0.d32 = DWC_READ_REG32(&dev_if->out_ep_regs[0]->doeptsiz); ++ ++ /** In BDMA more then 1 setup packet is not supported till 3.00a */ ++ if (core_if->dma_enable && core_if->dma_desc_enable == 0 ++ && (doeptsize0.b.supcnt < 2) ++ && (core_if->snpsid < OTG_CORE_REV_2_94a)) { ++ DWC_ERROR ++ ("\n\n----------- CANNOT handle > 1 setup packet in DMA mode\n\n"); ++ } ++ if ((core_if->snpsid >= OTG_CORE_REV_3_00a) ++ && (core_if->dma_enable == 1) && (core_if->dma_desc_enable == 0)) { ++ ctrl = ++ (pcd->setup_pkt + ++ (3 - doeptsize0.b.supcnt - 1 + ++ ep0->dwc_ep.stp_rollover))->req; ++ } ++#ifdef DEBUG_EP0 ++ DWC_DEBUGPL(DBG_PCD, "SETUP %02x.%02x v%04x i%04x l%04x\n", ++ ctrl.bmRequestType, ctrl.bRequest, ++ UGETW(ctrl.wValue), UGETW(ctrl.wIndex), ++ UGETW(ctrl.wLength)); ++#endif ++ ++ /* Clean up the request queue */ ++ dwc_otg_request_nuke(ep0); ++ ep0->stopped = 0; ++ ++ if (ctrl.bmRequestType & UE_DIR_IN) { ++ ep0->dwc_ep.is_in = 1; ++ pcd->ep0state = EP0_IN_DATA_PHASE; ++ } else { ++ ep0->dwc_ep.is_in = 0; ++ pcd->ep0state = EP0_OUT_DATA_PHASE; ++ } ++ ++ if (UGETW(ctrl.wLength) == 0) { ++ ep0->dwc_ep.is_in = 1; ++ pcd->ep0state = EP0_IN_STATUS_PHASE; ++ } ++ ++ if (UT_GET_TYPE(ctrl.bmRequestType) != UT_STANDARD) { ++ ++#ifdef DWC_UTE_CFI ++ DWC_MEMCPY(&cfi_req, &ctrl, sizeof(usb_device_request_t)); ++ ++ //printk(KERN_ALERT "CFI: req_type=0x%02x; req=0x%02x\n", ++ ctrl.bRequestType, ctrl.bRequest); ++ if (UT_GET_TYPE(cfi_req.bRequestType) == UT_VENDOR) { ++ if (cfi_req.bRequest > 0xB0 && cfi_req.bRequest < 0xBF) { ++ retval = cfi_setup(pcd, &cfi_req); ++ if (retval < 0) { ++ ep0_do_stall(pcd, retval); ++ pcd->ep0_pending = 0; ++ return; ++ } ++ ++ /* if need gadget setup then call it and check the retval */ ++ if (pcd->cfi->need_gadget_att) { ++ retval = ++ cfi_gadget_setup(pcd, ++ &pcd-> ++ cfi->ctrl_req); ++ if (retval < 0) { ++ pcd->ep0_pending = 0; ++ return; ++ } ++ } ++ ++ if (pcd->cfi->need_status_in_complete) { ++ do_setup_in_status_phase(pcd); ++ } ++ return; ++ } ++ } ++#endif ++ ++ /* handle non-standard (class/vendor) requests in the gadget driver */ ++ do_gadget_setup(pcd, &ctrl); ++ return; ++ } ++ ++ /** @todo NGS: Handle bad setup packet? */ ++ ++/////////////////////////////////////////// ++//// --- Standard Request handling --- //// ++ ++ switch (ctrl.bRequest) { ++ case UR_GET_STATUS: ++ do_get_status(pcd); ++ break; ++ ++ case UR_CLEAR_FEATURE: ++ do_clear_feature(pcd); ++ break; ++ ++ case UR_SET_FEATURE: ++ do_set_feature(pcd); ++ break; ++ ++ case UR_SET_ADDRESS: ++ do_set_address(pcd); ++ break; ++ ++ case UR_SET_INTERFACE: ++ case UR_SET_CONFIG: ++// _pcd->request_config = 1; /* Configuration changed */ ++ do_gadget_setup(pcd, &ctrl); ++ break; ++ ++ case UR_SYNCH_FRAME: ++ do_gadget_setup(pcd, &ctrl); ++ break; ++ ++ default: ++ /* Call the Gadget Driver's setup functions */ ++ do_gadget_setup(pcd, &ctrl); ++ break; ++ } ++} ++ ++/** ++ * This function completes the ep0 control transfer. ++ */ ++static int32_t ep0_complete_request(dwc_otg_pcd_ep_t * ep) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(ep->pcd); ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ dwc_otg_dev_in_ep_regs_t *in_ep_regs = ++ dev_if->in_ep_regs[ep->dwc_ep.num]; ++#ifdef DEBUG_EP0 ++ dwc_otg_dev_out_ep_regs_t *out_ep_regs = ++ dev_if->out_ep_regs[ep->dwc_ep.num]; ++#endif ++ deptsiz0_data_t deptsiz; ++ dev_dma_desc_sts_t desc_sts; ++ dwc_otg_pcd_request_t *req; ++ int is_last = 0; ++ dwc_otg_pcd_t *pcd = ep->pcd; ++ ++#ifdef DWC_UTE_CFI ++ struct cfi_usb_ctrlrequest *ctrlreq; ++ int retval = -DWC_E_NOT_SUPPORTED; ++#endif ++ ++ desc_sts.b.bytes = 0; ++ ++ if (pcd->ep0_pending && DWC_CIRCLEQ_EMPTY(&ep->queue)) { ++ if (ep->dwc_ep.is_in) { ++#ifdef DEBUG_EP0 ++ DWC_DEBUGPL(DBG_PCDV, "Do setup OUT status phase\n"); ++#endif ++ do_setup_out_status_phase(pcd); ++ } else { ++#ifdef DEBUG_EP0 ++ DWC_DEBUGPL(DBG_PCDV, "Do setup IN status phase\n"); ++#endif ++ ++#ifdef DWC_UTE_CFI ++ ctrlreq = &pcd->cfi->ctrl_req; ++ ++ if (UT_GET_TYPE(ctrlreq->bRequestType) == UT_VENDOR) { ++ if (ctrlreq->bRequest > 0xB0 ++ && ctrlreq->bRequest < 0xBF) { ++ ++ /* Return if the PCD failed to handle the request */ ++ if ((retval = ++ pcd->cfi->ops. ++ ctrl_write_complete(pcd->cfi, ++ pcd)) < 0) { ++ CFI_INFO ++ ("ERROR setting a new value in the PCD(%d)\n", ++ retval); ++ ep0_do_stall(pcd, retval); ++ pcd->ep0_pending = 0; ++ return 0; ++ } ++ ++ /* If the gadget needs to be notified on the request */ ++ if (pcd->cfi->need_gadget_att == 1) { ++ //retval = do_gadget_setup(pcd, &pcd->cfi->ctrl_req); ++ retval = ++ cfi_gadget_setup(pcd, ++ &pcd->cfi-> ++ ctrl_req); ++ ++ /* Return from the function if the gadget failed to process ++ * the request properly - this should never happen !!! ++ */ ++ if (retval < 0) { ++ CFI_INFO ++ ("ERROR setting a new value in the gadget(%d)\n", ++ retval); ++ pcd->ep0_pending = 0; ++ return 0; ++ } ++ } ++ ++ CFI_INFO("%s: RETVAL=%d\n", __func__, ++ retval); ++ /* If we hit here then the PCD and the gadget has properly ++ * handled the request - so send the ZLP IN to the host. ++ */ ++ /* @todo: MAS - decide whether we need to start the setup ++ * stage based on the need_setup value of the cfi object ++ */ ++ do_setup_in_status_phase(pcd); ++ pcd->ep0_pending = 0; ++ return 1; ++ } ++ } ++#endif ++ ++ do_setup_in_status_phase(pcd); ++ } ++ pcd->ep0_pending = 0; ++ return 1; ++ } ++ ++ if (DWC_CIRCLEQ_EMPTY(&ep->queue)) { ++ return 0; ++ } ++ req = DWC_CIRCLEQ_FIRST(&ep->queue); ++ ++ if (pcd->ep0state == EP0_OUT_STATUS_PHASE ++ || pcd->ep0state == EP0_IN_STATUS_PHASE) { ++ is_last = 1; ++ } else if (ep->dwc_ep.is_in) { ++ deptsiz.d32 = DWC_READ_REG32(&in_ep_regs->dieptsiz); ++ if (core_if->dma_desc_enable != 0) ++ desc_sts = dev_if->in_desc_addr->status; ++#ifdef DEBUG_EP0 ++ DWC_DEBUGPL(DBG_PCDV, "%d len=%d xfersize=%d pktcnt=%d\n", ++ ep->dwc_ep.num, ep->dwc_ep.xfer_len, ++ deptsiz.b.xfersize, deptsiz.b.pktcnt); ++#endif ++ ++ if (((core_if->dma_desc_enable == 0) ++ && (deptsiz.b.xfersize == 0)) ++ || ((core_if->dma_desc_enable != 0) ++ && (desc_sts.b.bytes == 0))) { ++ req->actual = ep->dwc_ep.xfer_count; ++ /* Is a Zero Len Packet needed? */ ++ if (req->sent_zlp) { ++#ifdef DEBUG_EP0 ++ DWC_DEBUGPL(DBG_PCD, "Setup Rx ZLP\n"); ++#endif ++ req->sent_zlp = 0; ++ } ++ do_setup_out_status_phase(pcd); ++ } ++ } else { ++ /* ep0-OUT */ ++#ifdef DEBUG_EP0 ++ deptsiz.d32 = DWC_READ_REG32(&out_ep_regs->doeptsiz); ++ DWC_DEBUGPL(DBG_PCDV, "%d len=%d xsize=%d pktcnt=%d\n", ++ ep->dwc_ep.num, ep->dwc_ep.xfer_len, ++ deptsiz.b.xfersize, deptsiz.b.pktcnt); ++#endif ++ req->actual = ep->dwc_ep.xfer_count; ++ ++ /* Is a Zero Len Packet needed? */ ++ if (req->sent_zlp) { ++#ifdef DEBUG_EP0 ++ DWC_DEBUGPL(DBG_PCDV, "Setup Tx ZLP\n"); ++#endif ++ req->sent_zlp = 0; ++ } ++ /* For older cores do setup in status phase in Slave/BDMA modes, ++ * starting from 3.00 do that only in slave, and for DMA modes ++ * just re-enable ep 0 OUT here*/ ++ if (core_if->dma_enable == 0 ++ || (core_if->dma_desc_enable == 0 ++ && core_if->snpsid <= OTG_CORE_REV_2_94a)) { ++ do_setup_in_status_phase(pcd); ++ } else if (core_if->snpsid >= OTG_CORE_REV_3_00a) { ++ DWC_DEBUGPL(DBG_PCDV, ++ "Enable out ep before in status phase\n"); ++ ep0_out_start(core_if, pcd); ++ } ++ } ++ ++ /* Complete the request */ ++ if (is_last) { ++ dwc_otg_request_done(ep, req, 0); ++ ep->dwc_ep.start_xfer_buff = 0; ++ ep->dwc_ep.xfer_buff = 0; ++ ep->dwc_ep.xfer_len = 0; ++ return 1; ++ } ++ return 0; ++} ++ ++#ifdef DWC_UTE_CFI ++/** ++ * This function calculates traverses all the CFI DMA descriptors and ++ * and accumulates the bytes that are left to be transfered. ++ * ++ * @return The total bytes left to transfered, or a negative value as failure ++ */ ++static inline int cfi_calc_desc_residue(dwc_otg_pcd_ep_t * ep) ++{ ++ int32_t ret = 0; ++ int i; ++ struct dwc_otg_dma_desc *ddesc = NULL; ++ struct cfi_ep *cfiep; ++ ++ /* See if the pcd_ep has its respective cfi_ep mapped */ ++ cfiep = get_cfi_ep_by_pcd_ep(ep->pcd->cfi, ep); ++ if (!cfiep) { ++ CFI_INFO("%s: Failed to find ep\n", __func__); ++ return -1; ++ } ++ ++ ddesc = ep->dwc_ep.descs; ++ ++ for (i = 0; (i < cfiep->desc_count) && (i < MAX_DMA_DESCS_PER_EP); i++) { ++ ++#if defined(PRINT_CFI_DMA_DESCS) ++ print_desc(ddesc, ep->ep.name, i); ++#endif ++ ret += ddesc->status.b.bytes; ++ ddesc++; ++ } ++ ++ if (ret) ++ CFI_INFO("!!!!!!!!!! WARNING (%s) - residue=%d\n", __func__, ++ ret); ++ ++ return ret; ++} ++#endif ++ ++/** ++ * This function completes the request for the EP. If there are ++ * additional requests for the EP in the queue they will be started. ++ */ ++static void complete_ep(dwc_otg_pcd_ep_t * ep) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(ep->pcd); ++ struct device *dev = dwc_otg_pcd_to_dev(ep->pcd); ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ dwc_otg_dev_in_ep_regs_t *in_ep_regs = ++ dev_if->in_ep_regs[ep->dwc_ep.num]; ++ deptsiz_data_t deptsiz; ++ dev_dma_desc_sts_t desc_sts; ++ dwc_otg_pcd_request_t *req = 0; ++ dwc_otg_dev_dma_desc_t *dma_desc; ++ uint32_t byte_count = 0; ++ int is_last = 0; ++ int i; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s() %d-%s\n", __func__, ep->dwc_ep.num, ++ (ep->dwc_ep.is_in ? "IN" : "OUT")); ++ ++ /* Get any pending requests */ ++ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) { ++ req = DWC_CIRCLEQ_FIRST(&ep->queue); ++ if (!req) { ++ DWC_PRINTF("complete_ep 0x%p, req = NULL!\n", ep); ++ return; ++ } ++ } else { ++ DWC_PRINTF("complete_ep 0x%p, ep->queue empty!\n", ep); ++ return; ++ } ++ ++ DWC_DEBUGPL(DBG_PCD, "Requests %d\n", ep->pcd->request_pending); ++ ++ if (ep->dwc_ep.is_in) { ++ deptsiz.d32 = DWC_READ_REG32(&in_ep_regs->dieptsiz); ++ ++ if (core_if->dma_enable) { ++ if (core_if->dma_desc_enable == 0) { ++ if (deptsiz.b.xfersize == 0 ++ && deptsiz.b.pktcnt == 0) { ++ byte_count = ++ ep->dwc_ep.xfer_len - ++ ep->dwc_ep.xfer_count; ++ ++ ep->dwc_ep.xfer_buff += byte_count; ++ ep->dwc_ep.dma_addr += byte_count; ++ ep->dwc_ep.xfer_count += byte_count; ++ ++ DWC_DEBUGPL(DBG_PCDV, ++ "%d-%s len=%d xfersize=%d pktcnt=%d\n", ++ ep->dwc_ep.num, ++ (ep->dwc_ep. ++ is_in ? "IN" : "OUT"), ++ ep->dwc_ep.xfer_len, ++ deptsiz.b.xfersize, ++ deptsiz.b.pktcnt); ++ ++ if (ep->dwc_ep.xfer_len < ++ ep->dwc_ep.total_len) { ++ dwc_otg_ep_start_transfer ++ (core_if, &ep->dwc_ep); ++ } else if (ep->dwc_ep.sent_zlp) { ++ /* ++ * This fragment of code should initiate 0 ++ * length transfer in case if it is queued ++ * a transfer with size divisible to EPs max ++ * packet size and with usb_request zero field ++ * is set, which means that after data is transfered, ++ * it is also should be transfered ++ * a 0 length packet at the end. For Slave and ++ * Buffer DMA modes in this case SW has ++ * to initiate 2 transfers one with transfer size, ++ * and the second with 0 size. For Descriptor ++ * DMA mode SW is able to initiate a transfer, ++ * which will handle all the packets including ++ * the last 0 length. ++ */ ++ ep->dwc_ep.sent_zlp = 0; ++ dwc_otg_ep_start_zl_transfer ++ (core_if, &ep->dwc_ep); ++ } else { ++ is_last = 1; ++ } ++ } else { ++ if (ep->dwc_ep.type == ++ DWC_OTG_EP_TYPE_ISOC) { ++ req->actual = 0; ++ dwc_otg_request_done(ep, req, 0); ++ ++ ep->dwc_ep.start_xfer_buff = 0; ++ ep->dwc_ep.xfer_buff = 0; ++ ep->dwc_ep.xfer_len = 0; ++ ++ /* If there is a request in the queue start it. */ ++ start_next_request(ep); ++ } else ++ DWC_WARN ++ ("Incomplete transfer (%d - %s [siz=%d pkt=%d])\n", ++ ep->dwc_ep.num, ++ (ep->dwc_ep.is_in ? "IN" : "OUT"), ++ deptsiz.b.xfersize, ++ deptsiz.b.pktcnt); ++ } ++ } else { ++ dma_desc = ep->dwc_ep.desc_addr; ++ byte_count = 0; ++ ep->dwc_ep.sent_zlp = 0; ++ ++#ifdef DWC_UTE_CFI ++ CFI_INFO("%s: BUFFER_MODE=%d\n", __func__, ++ ep->dwc_ep.buff_mode); ++ if (ep->dwc_ep.buff_mode != BM_STANDARD) { ++ int residue; ++ ++ residue = cfi_calc_desc_residue(ep); ++ if (residue < 0) ++ return; ++ ++ byte_count = residue; ++ } else { ++#endif ++ for (i = 0; i < ep->dwc_ep.desc_cnt; ++ ++i) { ++ desc_sts = dma_desc->status; ++ byte_count += desc_sts.b.bytes; ++ dma_desc++; ++ } ++#ifdef DWC_UTE_CFI ++ } ++#endif ++ if (byte_count == 0) { ++ ep->dwc_ep.xfer_count = ++ ep->dwc_ep.total_len; ++ is_last = 1; ++ } else { ++ DWC_WARN("Incomplete transfer\n"); ++ } ++ } ++ } else { ++ if (deptsiz.b.xfersize == 0 && deptsiz.b.pktcnt == 0) { ++ DWC_DEBUGPL(DBG_PCDV, ++ "%d-%s len=%d xfersize=%d pktcnt=%d\n", ++ ep->dwc_ep.num, ++ ep->dwc_ep.is_in ? "IN" : "OUT", ++ ep->dwc_ep.xfer_len, ++ deptsiz.b.xfersize, ++ deptsiz.b.pktcnt); ++ ++ /* Check if the whole transfer was completed, ++ * if no, setup transfer for next portion of data ++ */ ++ if (ep->dwc_ep.xfer_len < ep->dwc_ep.total_len) { ++ dwc_otg_ep_start_transfer(core_if, ++ &ep->dwc_ep); ++ } else if (ep->dwc_ep.sent_zlp) { ++ /* ++ * This fragment of code should initiate 0 ++ * length trasfer in case if it is queued ++ * a trasfer with size divisible to EPs max ++ * packet size and with usb_request zero field ++ * is set, which means that after data is transfered, ++ * it is also should be transfered ++ * a 0 length packet at the end. For Slave and ++ * Buffer DMA modes in this case SW has ++ * to initiate 2 transfers one with transfer size, ++ * and the second with 0 size. For Desriptor ++ * DMA mode SW is able to initiate a transfer, ++ * which will handle all the packets including ++ * the last 0 legth. ++ */ ++ ep->dwc_ep.sent_zlp = 0; ++ dwc_otg_ep_start_zl_transfer(core_if, ++ &ep->dwc_ep); ++ } else { ++ is_last = 1; ++ } ++ } else { ++ DWC_WARN ++ ("Incomplete transfer (%d-%s [siz=%d pkt=%d])\n", ++ ep->dwc_ep.num, ++ (ep->dwc_ep.is_in ? "IN" : "OUT"), ++ deptsiz.b.xfersize, deptsiz.b.pktcnt); ++ } ++ } ++ } else { ++ dwc_otg_dev_out_ep_regs_t *out_ep_regs = ++ dev_if->out_ep_regs[ep->dwc_ep.num]; ++ desc_sts.d32 = 0; ++ if (core_if->dma_enable) { ++ if (core_if->dma_desc_enable) { ++ dma_desc = ep->dwc_ep.desc_addr; ++ byte_count = 0; ++ ep->dwc_ep.sent_zlp = 0; ++ ++#ifdef DWC_UTE_CFI ++ CFI_INFO("%s: BUFFER_MODE=%d\n", __func__, ++ ep->dwc_ep.buff_mode); ++ if (ep->dwc_ep.buff_mode != BM_STANDARD) { ++ int residue; ++ residue = cfi_calc_desc_residue(ep); ++ if (residue < 0) ++ return; ++ byte_count = residue; ++ } else { ++#endif ++ ++ for (i = 0; i < ep->dwc_ep.desc_cnt; ++ ++i) { ++ desc_sts = dma_desc->status; ++ byte_count += desc_sts.b.bytes; ++ dma_desc++; ++ } ++ ++#ifdef DWC_UTE_CFI ++ } ++#endif ++ /* Checking for interrupt Out transfers with not ++ * dword aligned mps sizes ++ */ ++ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_INTR && ++ (ep->dwc_ep.maxpacket%4)) { ++ ep->dwc_ep.xfer_count = ++ ep->dwc_ep.total_len - byte_count; ++ if ((ep->dwc_ep.xfer_len % ++ ep->dwc_ep.maxpacket) ++ && (ep->dwc_ep.xfer_len / ++ ep->dwc_ep.maxpacket < ++ MAX_DMA_DESC_CNT)) ++ ep->dwc_ep.xfer_len -= ++ (ep->dwc_ep.desc_cnt - ++ 1) * ep->dwc_ep.maxpacket + ++ ep->dwc_ep.xfer_len % ++ ep->dwc_ep.maxpacket; ++ else ++ ep->dwc_ep.xfer_len -= ++ ep->dwc_ep.desc_cnt * ++ ep->dwc_ep.maxpacket; ++ if (ep->dwc_ep.xfer_len > 0) { ++ dwc_otg_ep_start_transfer ++ (core_if, &ep->dwc_ep); ++ } else { ++ is_last = 1; ++ } ++ } else { ++ ep->dwc_ep.xfer_count = ++ ep->dwc_ep.total_len - byte_count + ++ ((4 - ++ (ep->dwc_ep. ++ total_len & 0x3)) & 0x3); ++ is_last = 1; ++ } ++ } else { ++ deptsiz.d32 = 0; ++ deptsiz.d32 = ++ DWC_READ_REG32(&out_ep_regs->doeptsiz); ++ ++ byte_count = (ep->dwc_ep.xfer_len - ++ ep->dwc_ep.xfer_count - ++ deptsiz.b.xfersize); ++ ep->dwc_ep.xfer_buff += byte_count; ++ ep->dwc_ep.dma_addr += byte_count; ++ ep->dwc_ep.xfer_count += byte_count; ++ ++ /* Check if the whole transfer was completed, ++ * if no, setup transfer for next portion of data ++ */ ++ if (ep->dwc_ep.xfer_len < ep->dwc_ep.total_len) { ++ dwc_otg_ep_start_transfer(core_if, ++ &ep->dwc_ep); ++ } else if (ep->dwc_ep.sent_zlp) { ++ /* ++ * This fragment of code should initiate 0 ++ * length trasfer in case if it is queued ++ * a trasfer with size divisible to EPs max ++ * packet size and with usb_request zero field ++ * is set, which means that after data is transfered, ++ * it is also should be transfered ++ * a 0 length packet at the end. For Slave and ++ * Buffer DMA modes in this case SW has ++ * to initiate 2 transfers one with transfer size, ++ * and the second with 0 size. For Desriptor ++ * DMA mode SW is able to initiate a transfer, ++ * which will handle all the packets including ++ * the last 0 legth. ++ */ ++ ep->dwc_ep.sent_zlp = 0; ++ dwc_otg_ep_start_zl_transfer(core_if, ++ &ep->dwc_ep); ++ } else { ++ is_last = 1; ++ } ++ } ++ } else { ++ /* Check if the whole transfer was completed, ++ * if no, setup transfer for next portion of data ++ */ ++ if (ep->dwc_ep.xfer_len < ep->dwc_ep.total_len) { ++ dwc_otg_ep_start_transfer(core_if, &ep->dwc_ep); ++ } else if (ep->dwc_ep.sent_zlp) { ++ /* ++ * This fragment of code should initiate 0 ++ * length transfer in case if it is queued ++ * a transfer with size divisible to EPs max ++ * packet size and with usb_request zero field ++ * is set, which means that after data is transfered, ++ * it is also should be transfered ++ * a 0 length packet at the end. For Slave and ++ * Buffer DMA modes in this case SW has ++ * to initiate 2 transfers one with transfer size, ++ * and the second with 0 size. For Descriptor ++ * DMA mode SW is able to initiate a transfer, ++ * which will handle all the packets including ++ * the last 0 length. ++ */ ++ ep->dwc_ep.sent_zlp = 0; ++ dwc_otg_ep_start_zl_transfer(core_if, ++ &ep->dwc_ep); ++ } else { ++ is_last = 1; ++ } ++ } ++ ++ DWC_DEBUGPL(DBG_PCDV, ++ "addr %p, %d-%s len=%d cnt=%d xsize=%d pktcnt=%d\n", ++ &out_ep_regs->doeptsiz, ep->dwc_ep.num, ++ ep->dwc_ep.is_in ? "IN" : "OUT", ++ ep->dwc_ep.xfer_len, ep->dwc_ep.xfer_count, ++ deptsiz.b.xfersize, deptsiz.b.pktcnt); ++ } ++ ++ /* Complete the request */ ++ if (is_last) { ++#ifdef DWC_UTE_CFI ++ if (ep->dwc_ep.buff_mode != BM_STANDARD) { ++ req->actual = ep->dwc_ep.cfi_req_len - byte_count; ++ } else { ++#endif ++ req->actual = ep->dwc_ep.xfer_count; ++#ifdef DWC_UTE_CFI ++ } ++#endif ++ if (req->dw_align_buf) { ++ if (!ep->dwc_ep.is_in) { ++ dwc_memcpy(req->buf, req->dw_align_buf, req->length); ++ } ++ DWC_DMA_FREE(dev, req->length, req->dw_align_buf, ++ req->dw_align_buf_dma); ++ } ++ ++ dwc_otg_request_done(ep, req, 0); ++ ++ ep->dwc_ep.start_xfer_buff = 0; ++ ep->dwc_ep.xfer_buff = 0; ++ ep->dwc_ep.xfer_len = 0; ++ ++ /* If there is a request in the queue start it. */ ++ start_next_request(ep); ++ } ++} ++ ++#ifdef DWC_EN_ISOC ++ ++/** ++ * This function BNA interrupt for Isochronous EPs ++ * ++ */ ++static void dwc_otg_pcd_handle_iso_bna(dwc_otg_pcd_ep_t * ep) ++{ ++ dwc_ep_t *dwc_ep = &ep->dwc_ep; ++ volatile uint32_t *addr; ++ depctl_data_t depctl = {.d32 = 0 }; ++ dwc_otg_pcd_t *pcd = ep->pcd; ++ dwc_otg_dev_dma_desc_t *dma_desc; ++ int i; ++ ++ dma_desc = ++ dwc_ep->iso_desc_addr + dwc_ep->desc_cnt * (dwc_ep->proc_buf_num); ++ ++ if (dwc_ep->is_in) { ++ dev_dma_desc_sts_t sts = {.d32 = 0 }; ++ for (i = 0; i < dwc_ep->desc_cnt; ++i, ++dma_desc) { ++ sts.d32 = dma_desc->status.d32; ++ sts.b_iso_in.bs = BS_HOST_READY; ++ dma_desc->status.d32 = sts.d32; ++ } ++ } else { ++ dev_dma_desc_sts_t sts = {.d32 = 0 }; ++ for (i = 0; i < dwc_ep->desc_cnt; ++i, ++dma_desc) { ++ sts.d32 = dma_desc->status.d32; ++ sts.b_iso_out.bs = BS_HOST_READY; ++ dma_desc->status.d32 = sts.d32; ++ } ++ } ++ ++ if (dwc_ep->is_in == 0) { ++ addr = ++ &GET_CORE_IF(pcd)->dev_if->out_ep_regs[dwc_ep-> ++ num]->doepctl; ++ } else { ++ addr = ++ &GET_CORE_IF(pcd)->dev_if->in_ep_regs[dwc_ep->num]->diepctl; ++ } ++ depctl.b.epena = 1; ++ DWC_MODIFY_REG32(addr, depctl.d32, depctl.d32); ++} ++ ++/** ++ * This function sets latest iso packet information(non-PTI mode) ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to start the transfer on. ++ * ++ */ ++void set_current_pkt_info(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ deptsiz_data_t deptsiz = {.d32 = 0 }; ++ dma_addr_t dma_addr; ++ uint32_t offset; ++ ++ if (ep->proc_buf_num) ++ dma_addr = ep->dma_addr1; ++ else ++ dma_addr = ep->dma_addr0; ++ ++ if (ep->is_in) { ++ deptsiz.d32 = ++ DWC_READ_REG32(&core_if->dev_if-> ++ in_ep_regs[ep->num]->dieptsiz); ++ offset = ep->data_per_frame; ++ } else { ++ deptsiz.d32 = ++ DWC_READ_REG32(&core_if->dev_if-> ++ out_ep_regs[ep->num]->doeptsiz); ++ offset = ++ ep->data_per_frame + ++ (0x4 & (0x4 - (ep->data_per_frame & 0x3))); ++ } ++ ++ if (!deptsiz.b.xfersize) { ++ ep->pkt_info[ep->cur_pkt].length = ep->data_per_frame; ++ ep->pkt_info[ep->cur_pkt].offset = ++ ep->cur_pkt_dma_addr - dma_addr; ++ ep->pkt_info[ep->cur_pkt].status = 0; ++ } else { ++ ep->pkt_info[ep->cur_pkt].length = ep->data_per_frame; ++ ep->pkt_info[ep->cur_pkt].offset = ++ ep->cur_pkt_dma_addr - dma_addr; ++ ep->pkt_info[ep->cur_pkt].status = -DWC_E_NO_DATA; ++ } ++ ep->cur_pkt_addr += offset; ++ ep->cur_pkt_dma_addr += offset; ++ ep->cur_pkt++; ++} ++ ++/** ++ * This function sets latest iso packet information(DDMA mode) ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param dwc_ep The EP to start the transfer on. ++ * ++ */ ++static void set_ddma_iso_pkts_info(dwc_otg_core_if_t * core_if, ++ dwc_ep_t * dwc_ep) ++{ ++ dwc_otg_dev_dma_desc_t *dma_desc; ++ dev_dma_desc_sts_t sts = {.d32 = 0 }; ++ iso_pkt_info_t *iso_packet; ++ uint32_t data_per_desc; ++ uint32_t offset; ++ int i, j; ++ ++ iso_packet = dwc_ep->pkt_info; ++ ++ /** Reinit closed DMA Descriptors*/ ++ /** ISO OUT EP */ ++ if (dwc_ep->is_in == 0) { ++ dma_desc = ++ dwc_ep->iso_desc_addr + ++ dwc_ep->desc_cnt * dwc_ep->proc_buf_num; ++ offset = 0; ++ ++ for (i = 0; i < dwc_ep->desc_cnt - dwc_ep->pkt_per_frm; ++ i += dwc_ep->pkt_per_frm) { ++ for (j = 0; j < dwc_ep->pkt_per_frm; ++j) { ++ data_per_desc = ++ ((j + 1) * dwc_ep->maxpacket > ++ dwc_ep-> ++ data_per_frame) ? dwc_ep->data_per_frame - ++ j * dwc_ep->maxpacket : dwc_ep->maxpacket; ++ data_per_desc += ++ (data_per_desc % 4) ? (4 - ++ data_per_desc % ++ 4) : 0; ++ ++ sts.d32 = dma_desc->status.d32; ++ ++ /* Write status in iso_packet_decsriptor */ ++ iso_packet->status = ++ sts.b_iso_out.rxsts + ++ (sts.b_iso_out.bs ^ BS_DMA_DONE); ++ if (iso_packet->status) { ++ iso_packet->status = -DWC_E_NO_DATA; ++ } ++ ++ /* Received data length */ ++ if (!sts.b_iso_out.rxbytes) { ++ iso_packet->length = ++ data_per_desc - ++ sts.b_iso_out.rxbytes; ++ } else { ++ iso_packet->length = ++ data_per_desc - ++ sts.b_iso_out.rxbytes + (4 - ++ dwc_ep->data_per_frame ++ % 4); ++ } ++ ++ iso_packet->offset = offset; ++ ++ offset += data_per_desc; ++ dma_desc++; ++ iso_packet++; ++ } ++ } ++ ++ for (j = 0; j < dwc_ep->pkt_per_frm - 1; ++j) { ++ data_per_desc = ++ ((j + 1) * dwc_ep->maxpacket > ++ dwc_ep->data_per_frame) ? dwc_ep->data_per_frame - ++ j * dwc_ep->maxpacket : dwc_ep->maxpacket; ++ data_per_desc += ++ (data_per_desc % 4) ? (4 - data_per_desc % 4) : 0; ++ ++ sts.d32 = dma_desc->status.d32; ++ ++ /* Write status in iso_packet_decsriptor */ ++ iso_packet->status = ++ sts.b_iso_out.rxsts + ++ (sts.b_iso_out.bs ^ BS_DMA_DONE); ++ if (iso_packet->status) { ++ iso_packet->status = -DWC_E_NO_DATA; ++ } ++ ++ /* Received data length */ ++ iso_packet->length = ++ dwc_ep->data_per_frame - sts.b_iso_out.rxbytes; ++ ++ iso_packet->offset = offset; ++ ++ offset += data_per_desc; ++ iso_packet++; ++ dma_desc++; ++ } ++ ++ sts.d32 = dma_desc->status.d32; ++ ++ /* Write status in iso_packet_decsriptor */ ++ iso_packet->status = ++ sts.b_iso_out.rxsts + (sts.b_iso_out.bs ^ BS_DMA_DONE); ++ if (iso_packet->status) { ++ iso_packet->status = -DWC_E_NO_DATA; ++ } ++ /* Received data length */ ++ if (!sts.b_iso_out.rxbytes) { ++ iso_packet->length = ++ dwc_ep->data_per_frame - sts.b_iso_out.rxbytes; ++ } else { ++ iso_packet->length = ++ dwc_ep->data_per_frame - sts.b_iso_out.rxbytes + ++ (4 - dwc_ep->data_per_frame % 4); ++ } ++ ++ iso_packet->offset = offset; ++ } else { ++/** ISO IN EP */ ++ ++ dma_desc = ++ dwc_ep->iso_desc_addr + ++ dwc_ep->desc_cnt * dwc_ep->proc_buf_num; ++ ++ for (i = 0; i < dwc_ep->desc_cnt - 1; i++) { ++ sts.d32 = dma_desc->status.d32; ++ ++ /* Write status in iso packet descriptor */ ++ iso_packet->status = ++ sts.b_iso_in.txsts + ++ (sts.b_iso_in.bs ^ BS_DMA_DONE); ++ if (iso_packet->status != 0) { ++ iso_packet->status = -DWC_E_NO_DATA; ++ ++ } ++ /* Bytes has been transfered */ ++ iso_packet->length = ++ dwc_ep->data_per_frame - sts.b_iso_in.txbytes; ++ ++ dma_desc++; ++ iso_packet++; ++ } ++ ++ sts.d32 = dma_desc->status.d32; ++ while (sts.b_iso_in.bs == BS_DMA_BUSY) { ++ sts.d32 = dma_desc->status.d32; ++ } ++ ++ /* Write status in iso packet descriptor ??? do be done with ERROR codes */ ++ iso_packet->status = ++ sts.b_iso_in.txsts + (sts.b_iso_in.bs ^ BS_DMA_DONE); ++ if (iso_packet->status != 0) { ++ iso_packet->status = -DWC_E_NO_DATA; ++ } ++ ++ /* Bytes has been transfered */ ++ iso_packet->length = ++ dwc_ep->data_per_frame - sts.b_iso_in.txbytes; ++ } ++} ++ ++/** ++ * This function reinitialize DMA Descriptors for Isochronous transfer ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param dwc_ep The EP to start the transfer on. ++ * ++ */ ++static void reinit_ddma_iso_xfer(dwc_otg_core_if_t * core_if, dwc_ep_t * dwc_ep) ++{ ++ int i, j; ++ dwc_otg_dev_dma_desc_t *dma_desc; ++ dma_addr_t dma_ad; ++ volatile uint32_t *addr; ++ dev_dma_desc_sts_t sts = {.d32 = 0 }; ++ uint32_t data_per_desc; ++ ++ if (dwc_ep->is_in == 0) { ++ addr = &core_if->dev_if->out_ep_regs[dwc_ep->num]->doepctl; ++ } else { ++ addr = &core_if->dev_if->in_ep_regs[dwc_ep->num]->diepctl; ++ } ++ ++ if (dwc_ep->proc_buf_num == 0) { ++ /** Buffer 0 descriptors setup */ ++ dma_ad = dwc_ep->dma_addr0; ++ } else { ++ /** Buffer 1 descriptors setup */ ++ dma_ad = dwc_ep->dma_addr1; ++ } ++ ++ /** Reinit closed DMA Descriptors*/ ++ /** ISO OUT EP */ ++ if (dwc_ep->is_in == 0) { ++ dma_desc = ++ dwc_ep->iso_desc_addr + ++ dwc_ep->desc_cnt * dwc_ep->proc_buf_num; ++ ++ sts.b_iso_out.bs = BS_HOST_READY; ++ sts.b_iso_out.rxsts = 0; ++ sts.b_iso_out.l = 0; ++ sts.b_iso_out.sp = 0; ++ sts.b_iso_out.ioc = 0; ++ sts.b_iso_out.pid = 0; ++ sts.b_iso_out.framenum = 0; ++ ++ for (i = 0; i < dwc_ep->desc_cnt - dwc_ep->pkt_per_frm; ++ i += dwc_ep->pkt_per_frm) { ++ for (j = 0; j < dwc_ep->pkt_per_frm; ++j) { ++ data_per_desc = ++ ((j + 1) * dwc_ep->maxpacket > ++ dwc_ep-> ++ data_per_frame) ? dwc_ep->data_per_frame - ++ j * dwc_ep->maxpacket : dwc_ep->maxpacket; ++ data_per_desc += ++ (data_per_desc % 4) ? (4 - ++ data_per_desc % ++ 4) : 0; ++ sts.b_iso_out.rxbytes = data_per_desc; ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ ++ dma_ad += data_per_desc; ++ dma_desc++; ++ } ++ } ++ ++ for (j = 0; j < dwc_ep->pkt_per_frm - 1; ++j) { ++ ++ data_per_desc = ++ ((j + 1) * dwc_ep->maxpacket > ++ dwc_ep->data_per_frame) ? dwc_ep->data_per_frame - ++ j * dwc_ep->maxpacket : dwc_ep->maxpacket; ++ data_per_desc += ++ (data_per_desc % 4) ? (4 - data_per_desc % 4) : 0; ++ sts.b_iso_out.rxbytes = data_per_desc; ++ ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ ++ dma_desc++; ++ dma_ad += data_per_desc; ++ } ++ ++ sts.b_iso_out.ioc = 1; ++ sts.b_iso_out.l = dwc_ep->proc_buf_num; ++ ++ data_per_desc = ++ ((j + 1) * dwc_ep->maxpacket > ++ dwc_ep->data_per_frame) ? dwc_ep->data_per_frame - ++ j * dwc_ep->maxpacket : dwc_ep->maxpacket; ++ data_per_desc += ++ (data_per_desc % 4) ? (4 - data_per_desc % 4) : 0; ++ sts.b_iso_out.rxbytes = data_per_desc; ++ ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ } else { ++/** ISO IN EP */ ++ ++ dma_desc = ++ dwc_ep->iso_desc_addr + ++ dwc_ep->desc_cnt * dwc_ep->proc_buf_num; ++ ++ sts.b_iso_in.bs = BS_HOST_READY; ++ sts.b_iso_in.txsts = 0; ++ sts.b_iso_in.sp = 0; ++ sts.b_iso_in.ioc = 0; ++ sts.b_iso_in.pid = dwc_ep->pkt_per_frm; ++ sts.b_iso_in.framenum = dwc_ep->next_frame; ++ sts.b_iso_in.txbytes = dwc_ep->data_per_frame; ++ sts.b_iso_in.l = 0; ++ ++ for (i = 0; i < dwc_ep->desc_cnt - 1; i++) { ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ ++ sts.b_iso_in.framenum += dwc_ep->bInterval; ++ dma_ad += dwc_ep->data_per_frame; ++ dma_desc++; ++ } ++ ++ sts.b_iso_in.ioc = 1; ++ sts.b_iso_in.l = dwc_ep->proc_buf_num; ++ ++ dma_desc->buf = dma_ad; ++ dma_desc->status.d32 = sts.d32; ++ ++ dwc_ep->next_frame = ++ sts.b_iso_in.framenum + dwc_ep->bInterval * 1; ++ } ++ dwc_ep->proc_buf_num = (dwc_ep->proc_buf_num ^ 1) & 0x1; ++} ++ ++/** ++ * This function is to handle Iso EP transfer complete interrupt ++ * in case Iso out packet was dropped ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param dwc_ep The EP for wihich transfer complete was asserted ++ * ++ */ ++static uint32_t handle_iso_out_pkt_dropped(dwc_otg_core_if_t * core_if, ++ dwc_ep_t * dwc_ep) ++{ ++ uint32_t dma_addr; ++ uint32_t drp_pkt; ++ uint32_t drp_pkt_cnt; ++ deptsiz_data_t deptsiz = {.d32 = 0 }; ++ depctl_data_t depctl = {.d32 = 0 }; ++ int i; ++ ++ deptsiz.d32 = ++ DWC_READ_REG32(&core_if->dev_if-> ++ out_ep_regs[dwc_ep->num]->doeptsiz); ++ ++ drp_pkt = dwc_ep->pkt_cnt - deptsiz.b.pktcnt; ++ drp_pkt_cnt = dwc_ep->pkt_per_frm - (drp_pkt % dwc_ep->pkt_per_frm); ++ ++ /* Setting dropped packets status */ ++ for (i = 0; i < drp_pkt_cnt; ++i) { ++ dwc_ep->pkt_info[drp_pkt].status = -DWC_E_NO_DATA; ++ drp_pkt++; ++ deptsiz.b.pktcnt--; ++ } ++ ++ if (deptsiz.b.pktcnt > 0) { ++ deptsiz.b.xfersize = ++ dwc_ep->xfer_len - (dwc_ep->pkt_cnt - ++ deptsiz.b.pktcnt) * dwc_ep->maxpacket; ++ } else { ++ deptsiz.b.xfersize = 0; ++ deptsiz.b.pktcnt = 0; ++ } ++ ++ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[dwc_ep->num]->doeptsiz, ++ deptsiz.d32); ++ ++ if (deptsiz.b.pktcnt > 0) { ++ if (dwc_ep->proc_buf_num) { ++ dma_addr = ++ dwc_ep->dma_addr1 + dwc_ep->xfer_len - ++ deptsiz.b.xfersize; ++ } else { ++ dma_addr = ++ dwc_ep->dma_addr0 + dwc_ep->xfer_len - ++ deptsiz.b.xfersize;; ++ } ++ ++ DWC_WRITE_REG32(&core_if->dev_if-> ++ out_ep_regs[dwc_ep->num]->doepdma, dma_addr); ++ ++ /** Re-enable endpoint, clear nak */ ++ depctl.d32 = 0; ++ depctl.b.epena = 1; ++ depctl.b.cnak = 1; ++ ++ DWC_MODIFY_REG32(&core_if->dev_if-> ++ out_ep_regs[dwc_ep->num]->doepctl, depctl.d32, ++ depctl.d32); ++ return 0; ++ } else { ++ return 1; ++ } ++} ++ ++/** ++ * This function sets iso packets information(PTI mode) ++ * ++ * @param core_if Programming view of DWC_otg controller. ++ * @param ep The EP to start the transfer on. ++ * ++ */ ++static uint32_t set_iso_pkts_info(dwc_otg_core_if_t * core_if, dwc_ep_t * ep) ++{ ++ int i, j; ++ dma_addr_t dma_ad; ++ iso_pkt_info_t *packet_info = ep->pkt_info; ++ uint32_t offset; ++ uint32_t frame_data; ++ deptsiz_data_t deptsiz; ++ ++ if (ep->proc_buf_num == 0) { ++ /** Buffer 0 descriptors setup */ ++ dma_ad = ep->dma_addr0; ++ } else { ++ /** Buffer 1 descriptors setup */ ++ dma_ad = ep->dma_addr1; ++ } ++ ++ if (ep->is_in) { ++ deptsiz.d32 = ++ DWC_READ_REG32(&core_if->dev_if->in_ep_regs[ep->num]-> ++ dieptsiz); ++ } else { ++ deptsiz.d32 = ++ DWC_READ_REG32(&core_if->dev_if->out_ep_regs[ep->num]-> ++ doeptsiz); ++ } ++ ++ if (!deptsiz.b.xfersize) { ++ offset = 0; ++ for (i = 0; i < ep->pkt_cnt; i += ep->pkt_per_frm) { ++ frame_data = ep->data_per_frame; ++ for (j = 0; j < ep->pkt_per_frm; ++j) { ++ ++ /* Packet status - is not set as initially ++ * it is set to 0 and if packet was sent ++ successfully, status field will remain 0*/ ++ ++ /* Bytes has been transfered */ ++ packet_info->length = ++ (ep->maxpacket < ++ frame_data) ? ep->maxpacket : frame_data; ++ ++ /* Received packet offset */ ++ packet_info->offset = offset; ++ offset += packet_info->length; ++ frame_data -= packet_info->length; ++ ++ packet_info++; ++ } ++ } ++ return 1; ++ } else { ++ /* This is a workaround for in case of Transfer Complete with ++ * PktDrpSts interrupts merging - in this case Transfer complete ++ * interrupt for Isoc Out Endpoint is asserted without PktDrpSts ++ * set and with DOEPTSIZ register non zero. Investigations showed, ++ * that this happens when Out packet is dropped, but because of ++ * interrupts merging during first interrupt handling PktDrpSts ++ * bit is cleared and for next merged interrupts it is not reset. ++ * In this case SW hadles the interrupt as if PktDrpSts bit is set. ++ */ ++ if (ep->is_in) { ++ return 1; ++ } else { ++ return handle_iso_out_pkt_dropped(core_if, ep); ++ } ++ } ++} ++ ++/** ++ * This function is to handle Iso EP transfer complete interrupt ++ * ++ * @param pcd The PCD ++ * @param ep The EP for which transfer complete was asserted ++ * ++ */ ++static void complete_iso_ep(dwc_otg_pcd_t * pcd, dwc_otg_pcd_ep_t * ep) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(ep->pcd); ++ dwc_ep_t *dwc_ep = &ep->dwc_ep; ++ uint8_t is_last = 0; ++ ++ if (ep->dwc_ep.next_frame == 0xffffffff) { ++ DWC_WARN("Next frame is not set!\n"); ++ return; ++ } ++ ++ if (core_if->dma_enable) { ++ if (core_if->dma_desc_enable) { ++ set_ddma_iso_pkts_info(core_if, dwc_ep); ++ reinit_ddma_iso_xfer(core_if, dwc_ep); ++ is_last = 1; ++ } else { ++ if (core_if->pti_enh_enable) { ++ if (set_iso_pkts_info(core_if, dwc_ep)) { ++ dwc_ep->proc_buf_num = ++ (dwc_ep->proc_buf_num ^ 1) & 0x1; ++ dwc_otg_iso_ep_start_buf_transfer ++ (core_if, dwc_ep); ++ is_last = 1; ++ } ++ } else { ++ set_current_pkt_info(core_if, dwc_ep); ++ if (dwc_ep->cur_pkt >= dwc_ep->pkt_cnt) { ++ is_last = 1; ++ dwc_ep->cur_pkt = 0; ++ dwc_ep->proc_buf_num = ++ (dwc_ep->proc_buf_num ^ 1) & 0x1; ++ if (dwc_ep->proc_buf_num) { ++ dwc_ep->cur_pkt_addr = ++ dwc_ep->xfer_buff1; ++ dwc_ep->cur_pkt_dma_addr = ++ dwc_ep->dma_addr1; ++ } else { ++ dwc_ep->cur_pkt_addr = ++ dwc_ep->xfer_buff0; ++ dwc_ep->cur_pkt_dma_addr = ++ dwc_ep->dma_addr0; ++ } ++ ++ } ++ dwc_otg_iso_ep_start_frm_transfer(core_if, ++ dwc_ep); ++ } ++ } ++ } else { ++ set_current_pkt_info(core_if, dwc_ep); ++ if (dwc_ep->cur_pkt >= dwc_ep->pkt_cnt) { ++ is_last = 1; ++ dwc_ep->cur_pkt = 0; ++ dwc_ep->proc_buf_num = (dwc_ep->proc_buf_num ^ 1) & 0x1; ++ if (dwc_ep->proc_buf_num) { ++ dwc_ep->cur_pkt_addr = dwc_ep->xfer_buff1; ++ dwc_ep->cur_pkt_dma_addr = dwc_ep->dma_addr1; ++ } else { ++ dwc_ep->cur_pkt_addr = dwc_ep->xfer_buff0; ++ dwc_ep->cur_pkt_dma_addr = dwc_ep->dma_addr0; ++ } ++ ++ } ++ dwc_otg_iso_ep_start_frm_transfer(core_if, dwc_ep); ++ } ++ if (is_last) ++ dwc_otg_iso_buffer_done(pcd, ep, ep->iso_req_handle); ++} ++#endif /* DWC_EN_ISOC */ ++ ++/** ++ * This function handle BNA interrupt for Non Isochronous EPs ++ * ++ */ ++static void dwc_otg_pcd_handle_noniso_bna(dwc_otg_pcd_ep_t * ep) ++{ ++ dwc_ep_t *dwc_ep = &ep->dwc_ep; ++ volatile uint32_t *addr; ++ depctl_data_t depctl = {.d32 = 0 }; ++ dwc_otg_pcd_t *pcd = ep->pcd; ++ dwc_otg_dev_dma_desc_t *dma_desc; ++ dev_dma_desc_sts_t sts = {.d32 = 0 }; ++ dwc_otg_core_if_t *core_if = ep->pcd->core_if; ++ int i, start; ++ ++ if (!dwc_ep->desc_cnt) ++ DWC_WARN("Ep%d %s Descriptor count = %d \n", dwc_ep->num, ++ (dwc_ep->is_in ? "IN" : "OUT"), dwc_ep->desc_cnt); ++ ++ if (core_if->core_params->cont_on_bna && !dwc_ep->is_in ++ && dwc_ep->type != DWC_OTG_EP_TYPE_CONTROL) { ++ uint32_t doepdma; ++ dwc_otg_dev_out_ep_regs_t *out_regs = ++ core_if->dev_if->out_ep_regs[dwc_ep->num]; ++ doepdma = DWC_READ_REG32(&(out_regs->doepdma)); ++ start = (doepdma - dwc_ep->dma_desc_addr)/sizeof(dwc_otg_dev_dma_desc_t); ++ dma_desc = &(dwc_ep->desc_addr[start]); ++ } else { ++ start = 0; ++ dma_desc = dwc_ep->desc_addr; ++ } ++ ++ ++ for (i = start; i < dwc_ep->desc_cnt; ++i, ++dma_desc) { ++ sts.d32 = dma_desc->status.d32; ++ sts.b.bs = BS_HOST_READY; ++ dma_desc->status.d32 = sts.d32; ++ } ++ ++ if (dwc_ep->is_in == 0) { ++ addr = ++ &GET_CORE_IF(pcd)->dev_if->out_ep_regs[dwc_ep->num]-> ++ doepctl; ++ } else { ++ addr = ++ &GET_CORE_IF(pcd)->dev_if->in_ep_regs[dwc_ep->num]->diepctl; ++ } ++ depctl.b.epena = 1; ++ depctl.b.cnak = 1; ++ DWC_MODIFY_REG32(addr, 0, depctl.d32); ++} ++ ++/** ++ * This function handles EP0 Control transfers. ++ * ++ * The state of the control transfers are tracked in ++ * ep0state. ++ */ ++static void handle_ep0(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dwc_otg_pcd_ep_t *ep0 = &pcd->ep0; ++ dev_dma_desc_sts_t desc_sts; ++ deptsiz0_data_t deptsiz; ++ uint32_t byte_count; ++ ++#ifdef DEBUG_EP0 ++ DWC_DEBUGPL(DBG_PCDV, "%s()\n", __func__); ++ print_ep0_state(pcd); ++#endif ++ ++// DWC_PRINTF("HANDLE EP0\n"); ++ ++ switch (pcd->ep0state) { ++ case EP0_DISCONNECT: ++ break; ++ ++ case EP0_IDLE: ++ pcd->request_config = 0; ++ ++ pcd_setup(pcd); ++ break; ++ ++ case EP0_IN_DATA_PHASE: ++#ifdef DEBUG_EP0 ++ DWC_DEBUGPL(DBG_PCD, "DATA_IN EP%d-%s: type=%d, mps=%d\n", ++ ep0->dwc_ep.num, (ep0->dwc_ep.is_in ? "IN" : "OUT"), ++ ep0->dwc_ep.type, ep0->dwc_ep.maxpacket); ++#endif ++ ++ if (core_if->dma_enable != 0) { ++ /* ++ * For EP0 we can only program 1 packet at a time so we ++ * need to do the make calculations after each complete. ++ * Call write_packet to make the calculations, as in ++ * slave mode, and use those values to determine if we ++ * can complete. ++ */ ++ if (core_if->dma_desc_enable == 0) { ++ deptsiz.d32 = ++ DWC_READ_REG32(&core_if-> ++ dev_if->in_ep_regs[0]-> ++ dieptsiz); ++ byte_count = ++ ep0->dwc_ep.xfer_len - deptsiz.b.xfersize; ++ } else { ++ desc_sts = ++ core_if->dev_if->in_desc_addr->status; ++ byte_count = ++ ep0->dwc_ep.xfer_len - desc_sts.b.bytes; ++ } ++ ep0->dwc_ep.xfer_count += byte_count; ++ ep0->dwc_ep.xfer_buff += byte_count; ++ ep0->dwc_ep.dma_addr += byte_count; ++ } ++ if (ep0->dwc_ep.xfer_count < ep0->dwc_ep.total_len) { ++ dwc_otg_ep0_continue_transfer(GET_CORE_IF(pcd), ++ &ep0->dwc_ep); ++ DWC_DEBUGPL(DBG_PCD, "CONTINUE TRANSFER\n"); ++ } else if (ep0->dwc_ep.sent_zlp) { ++ dwc_otg_ep0_continue_transfer(GET_CORE_IF(pcd), ++ &ep0->dwc_ep); ++ ep0->dwc_ep.sent_zlp = 0; ++ DWC_DEBUGPL(DBG_PCD, "CONTINUE TRANSFER sent zlp\n"); ++ } else { ++ ep0_complete_request(ep0); ++ DWC_DEBUGPL(DBG_PCD, "COMPLETE TRANSFER\n"); ++ } ++ break; ++ case EP0_OUT_DATA_PHASE: ++#ifdef DEBUG_EP0 ++ DWC_DEBUGPL(DBG_PCD, "DATA_OUT EP%d-%s: type=%d, mps=%d\n", ++ ep0->dwc_ep.num, (ep0->dwc_ep.is_in ? "IN" : "OUT"), ++ ep0->dwc_ep.type, ep0->dwc_ep.maxpacket); ++#endif ++ if (core_if->dma_enable != 0) { ++ if (core_if->dma_desc_enable == 0) { ++ deptsiz.d32 = ++ DWC_READ_REG32(&core_if-> ++ dev_if->out_ep_regs[0]-> ++ doeptsiz); ++ byte_count = ++ ep0->dwc_ep.maxpacket - deptsiz.b.xfersize; ++ } else { ++ desc_sts = ++ core_if->dev_if->out_desc_addr->status; ++ byte_count = ++ ep0->dwc_ep.maxpacket - desc_sts.b.bytes; ++ } ++ ep0->dwc_ep.xfer_count += byte_count; ++ ep0->dwc_ep.xfer_buff += byte_count; ++ ep0->dwc_ep.dma_addr += byte_count; ++ } ++ if (ep0->dwc_ep.xfer_count < ep0->dwc_ep.total_len) { ++ dwc_otg_ep0_continue_transfer(GET_CORE_IF(pcd), ++ &ep0->dwc_ep); ++ DWC_DEBUGPL(DBG_PCD, "CONTINUE TRANSFER\n"); ++ } else if (ep0->dwc_ep.sent_zlp) { ++ dwc_otg_ep0_continue_transfer(GET_CORE_IF(pcd), ++ &ep0->dwc_ep); ++ ep0->dwc_ep.sent_zlp = 0; ++ DWC_DEBUGPL(DBG_PCD, "CONTINUE TRANSFER sent zlp\n"); ++ } else { ++ ep0_complete_request(ep0); ++ DWC_DEBUGPL(DBG_PCD, "COMPLETE TRANSFER\n"); ++ } ++ break; ++ ++ case EP0_IN_STATUS_PHASE: ++ case EP0_OUT_STATUS_PHASE: ++ DWC_DEBUGPL(DBG_PCD, "CASE: EP0_STATUS\n"); ++ ep0_complete_request(ep0); ++ pcd->ep0state = EP0_IDLE; ++ ep0->stopped = 1; ++ ep0->dwc_ep.is_in = 0; /* OUT for next SETUP */ ++ ++ /* Prepare for more SETUP Packets */ ++ if (core_if->dma_enable) { ++ ep0_out_start(core_if, pcd); ++ } ++ break; ++ ++ case EP0_STALL: ++ DWC_ERROR("EP0 STALLed, should not get here pcd_setup()\n"); ++ break; ++ } ++#ifdef DEBUG_EP0 ++ print_ep0_state(pcd); ++#endif ++} ++ ++/** ++ * Restart transfer ++ */ ++static void restart_transfer(dwc_otg_pcd_t * pcd, const uint32_t epnum) ++{ ++ dwc_otg_core_if_t *core_if; ++ dwc_otg_dev_if_t *dev_if; ++ deptsiz_data_t dieptsiz = {.d32 = 0 }; ++ dwc_otg_pcd_ep_t *ep; ++ ++ ep = get_in_ep(pcd, epnum); ++ ++#ifdef DWC_EN_ISOC ++ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) { ++ return; ++ } ++#endif /* DWC_EN_ISOC */ ++ ++ core_if = GET_CORE_IF(pcd); ++ dev_if = core_if->dev_if; ++ ++ dieptsiz.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dieptsiz); ++ ++ DWC_DEBUGPL(DBG_PCD, "xfer_buff=%p xfer_count=%0x xfer_len=%0x" ++ " stopped=%d\n", ep->dwc_ep.xfer_buff, ++ ep->dwc_ep.xfer_count, ep->dwc_ep.xfer_len, ep->stopped); ++ /* ++ * If xfersize is 0 and pktcnt in not 0, resend the last packet. ++ */ ++ if (dieptsiz.b.pktcnt && dieptsiz.b.xfersize == 0 && ++ ep->dwc_ep.start_xfer_buff != 0) { ++ if (ep->dwc_ep.total_len <= ep->dwc_ep.maxpacket) { ++ ep->dwc_ep.xfer_count = 0; ++ ep->dwc_ep.xfer_buff = ep->dwc_ep.start_xfer_buff; ++ ep->dwc_ep.xfer_len = ep->dwc_ep.xfer_count; ++ } else { ++ ep->dwc_ep.xfer_count -= ep->dwc_ep.maxpacket; ++ /* convert packet size to dwords. */ ++ ep->dwc_ep.xfer_buff -= ep->dwc_ep.maxpacket; ++ ep->dwc_ep.xfer_len = ep->dwc_ep.xfer_count; ++ } ++ ep->stopped = 0; ++ DWC_DEBUGPL(DBG_PCD, "xfer_buff=%p xfer_count=%0x " ++ "xfer_len=%0x stopped=%d\n", ++ ep->dwc_ep.xfer_buff, ++ ep->dwc_ep.xfer_count, ep->dwc_ep.xfer_len, ++ ep->stopped); ++ if (epnum == 0) { ++ dwc_otg_ep0_start_transfer(core_if, &ep->dwc_ep); ++ } else { ++ dwc_otg_ep_start_transfer(core_if, &ep->dwc_ep); ++ } ++ } ++} ++ ++/* ++ * This function create new nextep sequnce based on Learn Queue. ++ * ++ * @param core_if Programming view of DWC_otg controller ++ */ ++void predict_nextep_seq( dwc_otg_core_if_t * core_if) ++{ ++ dwc_otg_device_global_regs_t *dev_global_regs = ++ core_if->dev_if->dev_global_regs; ++ const uint32_t TOKEN_Q_DEPTH = core_if->hwcfg2.b.dev_token_q_depth; ++ /* Number of Token Queue Registers */ ++ const int DTKNQ_REG_CNT = (TOKEN_Q_DEPTH + 7) / 8; ++ dtknq1_data_t dtknqr1; ++ uint32_t in_tkn_epnums[4]; ++ uint8_t seqnum[MAX_EPS_CHANNELS]; ++ uint8_t intkn_seq[TOKEN_Q_DEPTH]; ++ grstctl_t resetctl = {.d32 = 0 }; ++ uint8_t temp; ++ int ndx = 0; ++ int start = 0; ++ int end = 0; ++ int sort_done = 0; ++ int i = 0; ++ volatile uint32_t *addr = &dev_global_regs->dtknqr1; ++ ++ ++ DWC_DEBUGPL(DBG_PCD,"dev_token_q_depth=%d\n",TOKEN_Q_DEPTH); ++ ++ /* Read the DTKNQ Registers */ ++ for (i = 0; i < DTKNQ_REG_CNT; i++) { ++ in_tkn_epnums[i] = DWC_READ_REG32(addr); ++ DWC_DEBUGPL(DBG_PCDV, "DTKNQR%d=0x%08x\n", i + 1, ++ in_tkn_epnums[i]); ++ if (addr == &dev_global_regs->dvbusdis) { ++ addr = &dev_global_regs->dtknqr3_dthrctl; ++ } else { ++ ++addr; ++ } ++ ++ } ++ ++ /* Copy the DTKNQR1 data to the bit field. */ ++ dtknqr1.d32 = in_tkn_epnums[0]; ++ if (dtknqr1.b.wrap_bit) { ++ ndx = dtknqr1.b.intknwptr; ++ end = ndx -1; ++ if (end < 0) ++ end = TOKEN_Q_DEPTH -1; ++ } else { ++ ndx = 0; ++ end = dtknqr1.b.intknwptr -1; ++ if (end < 0) ++ end = 0; ++ } ++ start = ndx; ++ ++ /* Fill seqnum[] by initial values: EP number + 31 */ ++ for (i=0; i <= core_if->dev_if->num_in_eps; i++) { ++ seqnum[i] = i +31; ++ } ++ ++ /* Fill intkn_seq[] from in_tkn_epnums[0] */ ++ for (i=0; i < 6; i++) ++ intkn_seq[i] = (in_tkn_epnums[0] >> ((7-i) * 4)) & 0xf; ++ ++ if (TOKEN_Q_DEPTH > 6) { ++ /* Fill intkn_seq[] from in_tkn_epnums[1] */ ++ for (i=6; i < 14; i++) ++ intkn_seq[i] = ++ (in_tkn_epnums[1] >> ((7 - (i - 6)) * 4)) & 0xf; ++ } ++ ++ if (TOKEN_Q_DEPTH > 14) { ++ /* Fill intkn_seq[] from in_tkn_epnums[1] */ ++ for (i=14; i < 22; i++) ++ intkn_seq[i] = ++ (in_tkn_epnums[2] >> ((7 - (i - 14)) * 4)) & 0xf; ++ } ++ ++ if (TOKEN_Q_DEPTH > 22) { ++ /* Fill intkn_seq[] from in_tkn_epnums[1] */ ++ for (i=22; i < 30; i++) ++ intkn_seq[i] = ++ (in_tkn_epnums[3] >> ((7 - (i - 22)) * 4)) & 0xf; ++ } ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s start=%d end=%d intkn_seq[]:\n", __func__, ++ start, end); ++ for (i=0; idev_if->num_in_eps; i++) { ++ if (core_if->nextep_seq[i] == 0xff ) ++ seqnum[i] = 0xff; ++ } ++ ++ /* Sort seqnum[] */ ++ sort_done = 0; ++ while (!sort_done) { ++ sort_done = 1; ++ for (i=0; idev_if->num_in_eps; i++) { ++ if (seqnum[i] > seqnum[i+1]) { ++ temp = seqnum[i]; ++ seqnum[i] = seqnum[i+1]; ++ seqnum[i+1] = temp; ++ sort_done = 0; ++ } ++ } ++ } ++ ++ ndx = start + seqnum[0]; ++ if (ndx >= TOKEN_Q_DEPTH) ++ ndx = ndx % TOKEN_Q_DEPTH; ++ core_if->first_in_nextep_seq = intkn_seq[ndx]; ++ ++ /* Update seqnum[] by EP numbers */ ++ for (i=0; i<=core_if->dev_if->num_in_eps; i++) { ++ ndx = start + i; ++ if (seqnum[i] < 31) { ++ ndx = start + seqnum[i]; ++ if (ndx >= TOKEN_Q_DEPTH) ++ ndx = ndx % TOKEN_Q_DEPTH; ++ seqnum[i] = intkn_seq[ndx]; ++ } else { ++ if (seqnum[i] < 0xff) { ++ seqnum[i] = seqnum[i] - 31; ++ } else { ++ break; ++ } ++ } ++ } ++ ++ /* Update nextep_seq[] based on seqnum[] */ ++ for (i=0; idev_if->num_in_eps; i++) { ++ if (seqnum[i] != 0xff) { ++ if (seqnum[i+1] != 0xff) { ++ core_if->nextep_seq[seqnum[i]] = seqnum[i+1]; ++ } else { ++ core_if->nextep_seq[seqnum[i]] = core_if->first_in_nextep_seq; ++ break; ++ } ++ } else { ++ break; ++ } ++ } ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s first_in_nextep_seq= %2d; nextep_seq[]:\n", ++ __func__, core_if->first_in_nextep_seq); ++ for (i=0; i <= core_if->dev_if->num_in_eps; i++) { ++ DWC_DEBUGPL(DBG_PCDV,"%2d\n", core_if->nextep_seq[i]); ++ } ++ ++ /* Flush the Learning Queue */ ++ resetctl.d32 = DWC_READ_REG32(&core_if->core_global_regs->grstctl); ++ resetctl.b.intknqflsh = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->grstctl, resetctl.d32); ++ ++ ++} ++ ++/** ++ * handle the IN EP disable interrupt. ++ */ ++static inline void handle_in_ep_disable_intr(dwc_otg_pcd_t * pcd, ++ const uint32_t epnum) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ deptsiz_data_t dieptsiz = {.d32 = 0 }; ++ dctl_data_t dctl = {.d32 = 0 }; ++ dwc_otg_pcd_ep_t *ep; ++ dwc_ep_t *dwc_ep; ++ gintmsk_data_t gintmsk_data; ++ depctl_data_t depctl; ++ uint32_t diepdma; ++ uint32_t remain_to_transfer = 0; ++ uint8_t i; ++ uint32_t xfer_size; ++ ++ ep = get_in_ep(pcd, epnum); ++ dwc_ep = &ep->dwc_ep; ++ ++ if (dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) { ++ dwc_otg_flush_tx_fifo(core_if, dwc_ep->tx_fifo_num); ++ complete_ep(ep); ++ return; ++ } ++ ++ DWC_DEBUGPL(DBG_PCD, "diepctl%d=%0x\n", epnum, ++ DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->diepctl)); ++ dieptsiz.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->dieptsiz); ++ depctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->diepctl); ++ ++ DWC_DEBUGPL(DBG_ANY, "pktcnt=%d size=%d\n", ++ dieptsiz.b.pktcnt, dieptsiz.b.xfersize); ++ ++ if ((core_if->start_predict == 0) || (depctl.b.eptype & 1)) { ++ if (ep->stopped) { ++ if (core_if->en_multiple_tx_fifo) ++ /* Flush the Tx FIFO */ ++ dwc_otg_flush_tx_fifo(core_if, dwc_ep->tx_fifo_num); ++ /* Clear the Global IN NP NAK */ ++ dctl.d32 = 0; ++ dctl.b.cgnpinnak = 1; ++ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dctl, dctl.d32, dctl.d32); ++ /* Restart the transaction */ ++ if (dieptsiz.b.pktcnt != 0 || dieptsiz.b.xfersize != 0) { ++ restart_transfer(pcd, epnum); ++ } ++ } else { ++ /* Restart the transaction */ ++ if (dieptsiz.b.pktcnt != 0 || dieptsiz.b.xfersize != 0) { ++ restart_transfer(pcd, epnum); ++ } ++ DWC_DEBUGPL(DBG_ANY, "STOPPED!!!\n"); ++ } ++ return; ++ } ++ ++ if (core_if->start_predict > 2) { // NP IN EP ++ core_if->start_predict--; ++ return; ++ } ++ ++ core_if->start_predict--; ++ ++ if (core_if->start_predict == 1) { // All NP IN Ep's disabled now ++ ++ predict_nextep_seq(core_if); ++ ++ /* Update all active IN EP's NextEP field based of nextep_seq[] */ ++ for ( i = 0; i <= core_if->dev_if->num_in_eps; i++) { ++ depctl.d32 = ++ DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl); ++ if (core_if->nextep_seq[i] != 0xff) { // Active NP IN EP ++ depctl.b.nextep = core_if->nextep_seq[i]; ++ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepctl, depctl.d32); ++ } ++ } ++ /* Flush Shared NP TxFIFO */ ++ dwc_otg_flush_tx_fifo(core_if, 0); ++ /* Rewind buffers */ ++ if (!core_if->dma_desc_enable) { ++ i = core_if->first_in_nextep_seq; ++ do { ++ ep = get_in_ep(pcd, i); ++ dieptsiz.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->dieptsiz); ++ xfer_size = ep->dwc_ep.total_len - ep->dwc_ep.xfer_count; ++ if (xfer_size > ep->dwc_ep.maxxfer) ++ xfer_size = ep->dwc_ep.maxxfer; ++ depctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl); ++ if (dieptsiz.b.pktcnt != 0) { ++ if (xfer_size == 0) { ++ remain_to_transfer = 0; ++ } else { ++ if ((xfer_size % ep->dwc_ep.maxpacket) == 0) { ++ remain_to_transfer = ++ dieptsiz.b.pktcnt * ep->dwc_ep.maxpacket; ++ } else { ++ remain_to_transfer = ((dieptsiz.b.pktcnt -1) * ep->dwc_ep.maxpacket) ++ + (xfer_size % ep->dwc_ep.maxpacket); ++ } ++ } ++ diepdma = DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepdma); ++ dieptsiz.b.xfersize = remain_to_transfer; ++ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->dieptsiz, dieptsiz.d32); ++ diepdma = ep->dwc_ep.dma_addr + (xfer_size - remain_to_transfer); ++ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepdma, diepdma); ++ } ++ i = core_if->nextep_seq[i]; ++ } while (i != core_if->first_in_nextep_seq); ++ } else { // dma_desc_enable ++ DWC_PRINTF("%s Learning Queue not supported in DDMA\n", __func__); ++ } ++ ++ /* Restart transfers in predicted sequences */ ++ i = core_if->first_in_nextep_seq; ++ do { ++ dieptsiz.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->dieptsiz); ++ depctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl); ++ if (dieptsiz.b.pktcnt != 0) { ++ depctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl); ++ depctl.b.epena = 1; ++ depctl.b.cnak = 1; ++ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepctl, depctl.d32); ++ } ++ i = core_if->nextep_seq[i]; ++ } while (i != core_if->first_in_nextep_seq); ++ ++ /* Clear the global non-periodic IN NAK handshake */ ++ dctl.d32 = 0; ++ dctl.b.cgnpinnak = 1; ++ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dctl, dctl.d32, dctl.d32); ++ ++ /* Unmask EP Mismatch interrupt */ ++ gintmsk_data.d32 = 0; ++ gintmsk_data.b.epmismatch = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, 0, gintmsk_data.d32); ++ ++ core_if->start_predict = 0; ++ ++ } ++} ++ ++/** ++ * Handler for the IN EP timeout handshake interrupt. ++ */ ++static inline void handle_in_ep_timeout_intr(dwc_otg_pcd_t * pcd, ++ const uint32_t epnum) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ ++#ifdef DEBUG ++ deptsiz_data_t dieptsiz = {.d32 = 0 }; ++ uint32_t num = 0; ++#endif ++ dctl_data_t dctl = {.d32 = 0 }; ++ dwc_otg_pcd_ep_t *ep; ++ ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ ep = get_in_ep(pcd, epnum); ++ ++ /* Disable the NP Tx Fifo Empty Interrrupt */ ++ if (!core_if->dma_enable) { ++ intr_mask.b.nptxfempty = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, ++ intr_mask.d32, 0); ++ } ++ /** @todo NGS Check EP type. ++ * Implement for Periodic EPs */ ++ /* ++ * Non-periodic EP ++ */ ++ /* Enable the Global IN NAK Effective Interrupt */ ++ intr_mask.b.ginnakeff = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, 0, intr_mask.d32); ++ ++ /* Set Global IN NAK */ ++ dctl.b.sgnpinnak = 1; ++ DWC_MODIFY_REG32(&dev_if->dev_global_regs->dctl, dctl.d32, dctl.d32); ++ ++ ep->stopped = 1; ++ ++#ifdef DEBUG ++ dieptsiz.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[num]->dieptsiz); ++ DWC_DEBUGPL(DBG_ANY, "pktcnt=%d size=%d\n", ++ dieptsiz.b.pktcnt, dieptsiz.b.xfersize); ++#endif ++ ++#ifdef DISABLE_PERIODIC_EP ++ /* ++ * Set the NAK bit for this EP to ++ * start the disable process. ++ */ ++ diepctl.d32 = 0; ++ diepctl.b.snak = 1; ++ DWC_MODIFY_REG32(&dev_if->in_ep_regs[num]->diepctl, diepctl.d32, ++ diepctl.d32); ++ ep->disabling = 1; ++ ep->stopped = 1; ++#endif ++} ++ ++/** ++ * Handler for the IN EP NAK interrupt. ++ */ ++static inline int32_t handle_in_ep_nak_intr(dwc_otg_pcd_t * pcd, ++ const uint32_t epnum) ++{ ++ /** @todo implement ISR */ ++ dwc_otg_core_if_t *core_if; ++ diepmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ DWC_PRINTF("INTERRUPT Handler not implemented for %s\n", "IN EP NAK"); ++ core_if = GET_CORE_IF(pcd); ++ intr_mask.b.nak = 1; ++ ++ if (core_if->multiproc_int_enable) { ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs-> ++ diepeachintmsk[epnum], intr_mask.d32, 0); ++ } else { ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->diepmsk, ++ intr_mask.d32, 0); ++ } ++ ++ return 1; ++} ++ ++/** ++ * Handler for the OUT EP Babble interrupt. ++ */ ++static inline int32_t handle_out_ep_babble_intr(dwc_otg_pcd_t * pcd, ++ const uint32_t epnum) ++{ ++ /** @todo implement ISR */ ++ dwc_otg_core_if_t *core_if; ++ doepmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ DWC_PRINTF("INTERRUPT Handler not implemented for %s\n", ++ "OUT EP Babble"); ++ core_if = GET_CORE_IF(pcd); ++ intr_mask.b.babble = 1; ++ ++ if (core_if->multiproc_int_enable) { ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs-> ++ doepeachintmsk[epnum], intr_mask.d32, 0); ++ } else { ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->doepmsk, ++ intr_mask.d32, 0); ++ } ++ ++ return 1; ++} ++ ++/** ++ * Handler for the OUT EP NAK interrupt. ++ */ ++static inline int32_t handle_out_ep_nak_intr(dwc_otg_pcd_t * pcd, ++ const uint32_t epnum) ++{ ++ /** @todo implement ISR */ ++ dwc_otg_core_if_t *core_if; ++ doepmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ DWC_DEBUGPL(DBG_ANY, "INTERRUPT Handler not implemented for %s\n", "OUT EP NAK"); ++ core_if = GET_CORE_IF(pcd); ++ intr_mask.b.nak = 1; ++ ++ if (core_if->multiproc_int_enable) { ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs-> ++ doepeachintmsk[epnum], intr_mask.d32, 0); ++ } else { ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->doepmsk, ++ intr_mask.d32, 0); ++ } ++ ++ return 1; ++} ++ ++/** ++ * Handler for the OUT EP NYET interrupt. ++ */ ++static inline int32_t handle_out_ep_nyet_intr(dwc_otg_pcd_t * pcd, ++ const uint32_t epnum) ++{ ++ /** @todo implement ISR */ ++ dwc_otg_core_if_t *core_if; ++ doepmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ DWC_PRINTF("INTERRUPT Handler not implemented for %s\n", "OUT EP NYET"); ++ core_if = GET_CORE_IF(pcd); ++ intr_mask.b.nyet = 1; ++ ++ if (core_if->multiproc_int_enable) { ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs-> ++ doepeachintmsk[epnum], intr_mask.d32, 0); ++ } else { ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->doepmsk, ++ intr_mask.d32, 0); ++ } ++ ++ return 1; ++} ++ ++/** ++ * This interrupt indicates that an IN EP has a pending Interrupt. ++ * The sequence for handling the IN EP interrupt is shown below: ++ * -# Read the Device All Endpoint Interrupt register ++ * -# Repeat the following for each IN EP interrupt bit set (from ++ * LSB to MSB). ++ * -# Read the Device Endpoint Interrupt (DIEPINTn) register ++ * -# If "Transfer Complete" call the request complete function ++ * -# If "Endpoint Disabled" complete the EP disable procedure. ++ * -# If "AHB Error Interrupt" log error ++ * -# If "Time-out Handshake" log error ++ * -# If "IN Token Received when TxFIFO Empty" write packet to Tx ++ * FIFO. ++ * -# If "IN Token EP Mismatch" (disable, this is handled by EP ++ * Mismatch Interrupt) ++ */ ++static int32_t dwc_otg_pcd_handle_in_ep_intr(dwc_otg_pcd_t * pcd) ++{ ++#define CLEAR_IN_EP_INTR(__core_if,__epnum,__intr) \ ++do { \ ++ diepint_data_t diepint = {.d32=0}; \ ++ diepint.b.__intr = 1; \ ++ DWC_WRITE_REG32(&__core_if->dev_if->in_ep_regs[__epnum]->diepint, \ ++ diepint.d32); \ ++} while (0) ++ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ dwc_otg_dev_if_t *dev_if = core_if->dev_if; ++ diepint_data_t diepint = {.d32 = 0 }; ++ depctl_data_t depctl = {.d32 = 0 }; ++ uint32_t ep_intr; ++ uint32_t epnum = 0; ++ dwc_otg_pcd_ep_t *ep; ++ dwc_ep_t *dwc_ep; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, pcd); ++ ++ /* Read in the device interrupt bits */ ++ ep_intr = dwc_otg_read_dev_all_in_ep_intr(core_if); ++ ++ /* Service the Device IN interrupts for each endpoint */ ++ while (ep_intr) { ++ if (ep_intr & 0x1) { ++ uint32_t empty_msk; ++ /* Get EP pointer */ ++ ep = get_in_ep(pcd, epnum); ++ dwc_ep = &ep->dwc_ep; ++ ++ depctl.d32 = ++ DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->diepctl); ++ empty_msk = ++ DWC_READ_REG32(&dev_if-> ++ dev_global_regs->dtknqr4_fifoemptymsk); ++ ++ DWC_DEBUGPL(DBG_PCDV, ++ "IN EP INTERRUPT - %d\nepmty_msk - %8x diepctl - %8x\n", ++ epnum, empty_msk, depctl.d32); ++ ++ DWC_DEBUGPL(DBG_PCD, ++ "EP%d-%s: type=%d, mps=%d\n", ++ dwc_ep->num, (dwc_ep->is_in ? "IN" : "OUT"), ++ dwc_ep->type, dwc_ep->maxpacket); ++ ++ diepint.d32 = ++ dwc_otg_read_dev_in_ep_intr(core_if, dwc_ep); ++ ++ DWC_DEBUGPL(DBG_PCDV, ++ "EP %d Interrupt Register - 0x%x\n", epnum, ++ diepint.d32); ++ /* Transfer complete */ ++ if (diepint.b.xfercompl) { ++ /* Disable the NP Tx FIFO Empty ++ * Interrupt */ ++ if (core_if->en_multiple_tx_fifo == 0) { ++ intr_mask.b.nptxfempty = 1; ++ DWC_MODIFY_REG32 ++ (&core_if->core_global_regs->gintmsk, ++ intr_mask.d32, 0); ++ } else { ++ /* Disable the Tx FIFO Empty Interrupt for this EP */ ++ uint32_t fifoemptymsk = ++ 0x1 << dwc_ep->num; ++ DWC_MODIFY_REG32(&core_if-> ++ dev_if->dev_global_regs->dtknqr4_fifoemptymsk, ++ fifoemptymsk, 0); ++ } ++ /* Clear the bit in DIEPINTn for this interrupt */ ++ CLEAR_IN_EP_INTR(core_if, epnum, xfercompl); ++ ++ /* Complete the transfer */ ++ if (epnum == 0) { ++ handle_ep0(pcd); ++ } ++#ifdef DWC_EN_ISOC ++ else if (dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) { ++ if (!ep->stopped) ++ complete_iso_ep(pcd, ep); ++ } ++#endif /* DWC_EN_ISOC */ ++#ifdef DWC_UTE_PER_IO ++ else if (dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) { ++ if (!ep->stopped) ++ complete_xiso_ep(ep); ++ } ++#endif /* DWC_UTE_PER_IO */ ++ else { ++ if (dwc_ep->type == DWC_OTG_EP_TYPE_ISOC && ++ dwc_ep->bInterval > 1) { ++ dwc_ep->frame_num += dwc_ep->bInterval; ++ if (dwc_ep->frame_num > 0x3FFF) ++ { ++ dwc_ep->frm_overrun = 1; ++ dwc_ep->frame_num &= 0x3FFF; ++ } else ++ dwc_ep->frm_overrun = 0; ++ } ++ complete_ep(ep); ++ if(diepint.b.nak) ++ CLEAR_IN_EP_INTR(core_if, epnum, nak); ++ } ++ } ++ /* Endpoint disable */ ++ if (diepint.b.epdisabled) { ++ DWC_DEBUGPL(DBG_ANY, "EP%d IN disabled\n", ++ epnum); ++ handle_in_ep_disable_intr(pcd, epnum); ++ ++ /* Clear the bit in DIEPINTn for this interrupt */ ++ CLEAR_IN_EP_INTR(core_if, epnum, epdisabled); ++ } ++ /* AHB Error */ ++ if (diepint.b.ahberr) { ++ DWC_ERROR("EP%d IN AHB Error\n", epnum); ++ /* Clear the bit in DIEPINTn for this interrupt */ ++ CLEAR_IN_EP_INTR(core_if, epnum, ahberr); ++ } ++ /* TimeOUT Handshake (non-ISOC IN EPs) */ ++ if (diepint.b.timeout) { ++ DWC_ERROR("EP%d IN Time-out\n", epnum); ++ handle_in_ep_timeout_intr(pcd, epnum); ++ ++ CLEAR_IN_EP_INTR(core_if, epnum, timeout); ++ } ++ /** IN Token received with TxF Empty */ ++ if (diepint.b.intktxfemp) { ++ DWC_DEBUGPL(DBG_ANY, ++ "EP%d IN TKN TxFifo Empty\n", ++ epnum); ++ if (!ep->stopped && epnum != 0) { ++ ++ diepmsk_data_t diepmsk = {.d32 = 0 }; ++ diepmsk.b.intktxfemp = 1; ++ ++ if (core_if->multiproc_int_enable) { ++ DWC_MODIFY_REG32 ++ (&dev_if->dev_global_regs->diepeachintmsk ++ [epnum], diepmsk.d32, 0); ++ } else { ++ DWC_MODIFY_REG32 ++ (&dev_if->dev_global_regs->diepmsk, ++ diepmsk.d32, 0); ++ } ++ } else if (core_if->dma_desc_enable ++ && epnum == 0 ++ && pcd->ep0state == ++ EP0_OUT_STATUS_PHASE) { ++ // EP0 IN set STALL ++ depctl.d32 = ++ DWC_READ_REG32(&dev_if->in_ep_regs ++ [epnum]->diepctl); ++ ++ /* set the disable and stall bits */ ++ if (depctl.b.epena) { ++ depctl.b.epdis = 1; ++ } ++ depctl.b.stall = 1; ++ DWC_WRITE_REG32(&dev_if->in_ep_regs ++ [epnum]->diepctl, ++ depctl.d32); ++ } ++ CLEAR_IN_EP_INTR(core_if, epnum, intktxfemp); ++ } ++ /** IN Token Received with EP mismatch */ ++ if (diepint.b.intknepmis) { ++ DWC_DEBUGPL(DBG_ANY, ++ "EP%d IN TKN EP Mismatch\n", epnum); ++ CLEAR_IN_EP_INTR(core_if, epnum, intknepmis); ++ } ++ /** IN Endpoint NAK Effective */ ++ if (diepint.b.inepnakeff) { ++ DWC_DEBUGPL(DBG_ANY, ++ "EP%d IN EP NAK Effective\n", ++ epnum); ++ /* Periodic EP */ ++ if (ep->disabling) { ++ depctl.d32 = 0; ++ depctl.b.snak = 1; ++ depctl.b.epdis = 1; ++ DWC_MODIFY_REG32(&dev_if->in_ep_regs ++ [epnum]->diepctl, ++ depctl.d32, ++ depctl.d32); ++ } ++ CLEAR_IN_EP_INTR(core_if, epnum, inepnakeff); ++ ++ } ++ ++ /** IN EP Tx FIFO Empty Intr */ ++ if (diepint.b.emptyintr) { ++ DWC_DEBUGPL(DBG_ANY, ++ "EP%d Tx FIFO Empty Intr \n", ++ epnum); ++ write_empty_tx_fifo(pcd, epnum); ++ ++ CLEAR_IN_EP_INTR(core_if, epnum, emptyintr); ++ ++ } ++ ++ /** IN EP BNA Intr */ ++ if (diepint.b.bna) { ++ CLEAR_IN_EP_INTR(core_if, epnum, bna); ++ if (core_if->dma_desc_enable) { ++#ifdef DWC_EN_ISOC ++ if (dwc_ep->type == ++ DWC_OTG_EP_TYPE_ISOC) { ++ /* ++ * This checking is performed to prevent first "false" BNA ++ * handling occuring right after reconnect ++ */ ++ if (dwc_ep->next_frame != ++ 0xffffffff) ++ dwc_otg_pcd_handle_iso_bna(ep); ++ } else ++#endif /* DWC_EN_ISOC */ ++ { ++ dwc_otg_pcd_handle_noniso_bna(ep); ++ } ++ } ++ } ++ /* NAK Interrutp */ ++ if (diepint.b.nak) { ++ DWC_DEBUGPL(DBG_ANY, "EP%d IN NAK Interrupt\n", ++ epnum); ++ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) { ++ depctl_data_t depctl; ++ if (ep->dwc_ep.frame_num == 0xFFFFFFFF) { ++ ep->dwc_ep.frame_num = core_if->frame_num; ++ if (ep->dwc_ep.bInterval > 1) { ++ depctl.d32 = 0; ++ depctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[epnum]->diepctl); ++ if (ep->dwc_ep.frame_num & 0x1) { ++ depctl.b.setd1pid = 1; ++ depctl.b.setd0pid = 0; ++ } else { ++ depctl.b.setd0pid = 1; ++ depctl.b.setd1pid = 0; ++ } ++ DWC_WRITE_REG32(&dev_if->in_ep_regs[epnum]->diepctl, depctl.d32); ++ } ++ start_next_request(ep); ++ } ++ ep->dwc_ep.frame_num += ep->dwc_ep.bInterval; ++ if (dwc_ep->frame_num > 0x3FFF) { ++ dwc_ep->frm_overrun = 1; ++ dwc_ep->frame_num &= 0x3FFF; ++ } else ++ dwc_ep->frm_overrun = 0; ++ } ++ ++ CLEAR_IN_EP_INTR(core_if, epnum, nak); ++ } ++ } ++ epnum++; ++ ep_intr >>= 1; ++ } ++ ++ return 1; ++#undef CLEAR_IN_EP_INTR ++} ++ ++/** ++ * This interrupt indicates that an OUT EP has a pending Interrupt. ++ * The sequence for handling the OUT EP interrupt is shown below: ++ * -# Read the Device All Endpoint Interrupt register ++ * -# Repeat the following for each OUT EP interrupt bit set (from ++ * LSB to MSB). ++ * -# Read the Device Endpoint Interrupt (DOEPINTn) register ++ * -# If "Transfer Complete" call the request complete function ++ * -# If "Endpoint Disabled" complete the EP disable procedure. ++ * -# If "AHB Error Interrupt" log error ++ * -# If "Setup Phase Done" process Setup Packet (See Standard USB ++ * Command Processing) ++ */ ++static int32_t dwc_otg_pcd_handle_out_ep_intr(dwc_otg_pcd_t * pcd) ++{ ++#define CLEAR_OUT_EP_INTR(__core_if,__epnum,__intr) \ ++do { \ ++ doepint_data_t doepint = {.d32=0}; \ ++ doepint.b.__intr = 1; \ ++ DWC_WRITE_REG32(&__core_if->dev_if->out_ep_regs[__epnum]->doepint, \ ++ doepint.d32); \ ++} while (0) ++ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ uint32_t ep_intr; ++ doepint_data_t doepint = {.d32 = 0 }; ++ uint32_t epnum = 0; ++ dwc_otg_pcd_ep_t *ep; ++ dwc_ep_t *dwc_ep; ++ dctl_data_t dctl = {.d32 = 0 }; ++ gintmsk_data_t gintmsk = {.d32 = 0 }; ++ ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s()\n", __func__); ++ ++ /* Read in the device interrupt bits */ ++ ep_intr = dwc_otg_read_dev_all_out_ep_intr(core_if); ++ ++ while (ep_intr) { ++ if (ep_intr & 0x1) { ++ /* Get EP pointer */ ++ ep = get_out_ep(pcd, epnum); ++ dwc_ep = &ep->dwc_ep; ++ ++#ifdef VERBOSE ++ DWC_DEBUGPL(DBG_PCDV, ++ "EP%d-%s: type=%d, mps=%d\n", ++ dwc_ep->num, (dwc_ep->is_in ? "IN" : "OUT"), ++ dwc_ep->type, dwc_ep->maxpacket); ++#endif ++ doepint.d32 = ++ dwc_otg_read_dev_out_ep_intr(core_if, dwc_ep); ++ /* Moved this interrupt upper due to core deffect of asserting ++ * OUT EP 0 xfercompl along with stsphsrcvd in BDMA */ ++ if (doepint.b.stsphsercvd) { ++ deptsiz0_data_t deptsiz; ++ CLEAR_OUT_EP_INTR(core_if, epnum, stsphsercvd); ++ deptsiz.d32 = ++ DWC_READ_REG32(&core_if->dev_if-> ++ out_ep_regs[0]->doeptsiz); ++ if (core_if->snpsid >= OTG_CORE_REV_3_00a ++ && core_if->dma_enable ++ && core_if->dma_desc_enable == 0 ++ && doepint.b.xfercompl ++ && deptsiz.b.xfersize == 24) { ++ CLEAR_OUT_EP_INTR(core_if, epnum, ++ xfercompl); ++ doepint.b.xfercompl = 0; ++ ep0_out_start(core_if, pcd); ++ } ++ if ((core_if->dma_desc_enable) || ++ (core_if->dma_enable ++ && core_if->snpsid >= ++ OTG_CORE_REV_3_00a)) { ++ do_setup_in_status_phase(pcd); ++ } ++ } ++ /* Transfer complete */ ++ if (doepint.b.xfercompl) { ++ ++ if (epnum == 0) { ++ /* Clear the bit in DOEPINTn for this interrupt */ ++ CLEAR_OUT_EP_INTR(core_if, epnum, xfercompl); ++ if (core_if->snpsid >= OTG_CORE_REV_3_00a) { ++ DWC_DEBUGPL(DBG_PCDV, "DOEPINT=%x doepint=%x\n", ++ DWC_READ_REG32(&core_if->dev_if->out_ep_regs[0]->doepint), ++ doepint.d32); ++ DWC_DEBUGPL(DBG_PCDV, "DOEPCTL=%x \n", ++ DWC_READ_REG32(&core_if->dev_if->out_ep_regs[0]->doepctl)); ++ ++ if (core_if->snpsid >= OTG_CORE_REV_3_00a ++ && core_if->dma_enable == 0) { ++ doepint_data_t doepint; ++ doepint.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ out_ep_regs[0]->doepint); ++ if (pcd->ep0state == EP0_IDLE && doepint.b.sr) { ++ CLEAR_OUT_EP_INTR(core_if, epnum, sr); ++ goto exit_xfercompl; ++ } ++ } ++ /* In case of DDMA look at SR bit to go to the Data Stage */ ++ if (core_if->dma_desc_enable) { ++ dev_dma_desc_sts_t status = {.d32 = 0}; ++ if (pcd->ep0state == EP0_IDLE) { ++ status.d32 = core_if->dev_if->setup_desc_addr[core_if-> ++ dev_if->setup_desc_index]->status.d32; ++ if(pcd->data_terminated) { ++ pcd->data_terminated = 0; ++ status.d32 = core_if->dev_if->out_desc_addr->status.d32; ++ dwc_memcpy(&pcd->setup_pkt->req, pcd->backup_buf, 8); ++ } ++ if (status.b.sr) { ++ if (doepint.b.setup) { ++ DWC_DEBUGPL(DBG_PCDV, "DMA DESC EP0_IDLE SR=1 setup=1\n"); ++ /* Already started data stage, clear setup */ ++ CLEAR_OUT_EP_INTR(core_if, epnum, setup); ++ doepint.b.setup = 0; ++ handle_ep0(pcd); ++ /* Prepare for more setup packets */ ++ if (pcd->ep0state == EP0_IN_STATUS_PHASE || ++ pcd->ep0state == EP0_IN_DATA_PHASE) { ++ ep0_out_start(core_if, pcd); ++ } ++ ++ goto exit_xfercompl; ++ } else { ++ /* Prepare for more setup packets */ ++ DWC_DEBUGPL(DBG_PCDV, ++ "EP0_IDLE SR=1 setup=0 new setup comes\n"); ++ ep0_out_start(core_if, pcd); ++ } ++ } ++ } else { ++ dwc_otg_pcd_request_t *req; ++ dev_dma_desc_sts_t status = {.d32 = 0}; ++ diepint_data_t diepint0; ++ diepint0.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ in_ep_regs[0]->diepint); ++ ++ if (pcd->ep0state == EP0_STALL || pcd->ep0state == EP0_DISCONNECT) { ++ DWC_ERROR("EP0 is stalled/disconnected\n"); ++ } ++ ++ /* Clear IN xfercompl if set */ ++ if (diepint0.b.xfercompl && (pcd->ep0state == EP0_IN_STATUS_PHASE ++ || pcd->ep0state == EP0_IN_DATA_PHASE)) { ++ DWC_WRITE_REG32(&core_if->dev_if-> ++ in_ep_regs[0]->diepint, diepint0.d32); ++ } ++ ++ status.d32 = core_if->dev_if->setup_desc_addr[core_if-> ++ dev_if->setup_desc_index]->status.d32; ++ ++ if (ep->dwc_ep.xfer_count != ep->dwc_ep.total_len ++ && (pcd->ep0state == EP0_OUT_DATA_PHASE)) ++ status.d32 = core_if->dev_if->out_desc_addr->status.d32; ++ if (pcd->ep0state == EP0_OUT_STATUS_PHASE) ++ status.d32 = core_if->dev_if-> ++ out_desc_addr->status.d32; ++ ++ if (status.b.sr) { ++ if (DWC_CIRCLEQ_EMPTY(&ep->queue)) { ++ DWC_DEBUGPL(DBG_PCDV, "Request queue empty!!\n"); ++ } else { ++ DWC_DEBUGPL(DBG_PCDV, "complete req!!\n"); ++ req = DWC_CIRCLEQ_FIRST(&ep->queue); ++ if (ep->dwc_ep.xfer_count != ep->dwc_ep.total_len && ++ pcd->ep0state == EP0_OUT_DATA_PHASE) { ++ /* Read arrived setup packet from req->buf */ ++ dwc_memcpy(&pcd->setup_pkt->req, ++ req->buf + ep->dwc_ep.xfer_count, 8); ++ } ++ req->actual = ep->dwc_ep.xfer_count; ++ dwc_otg_request_done(ep, req, -ECONNRESET); ++ ep->dwc_ep.start_xfer_buff = 0; ++ ep->dwc_ep.xfer_buff = 0; ++ ep->dwc_ep.xfer_len = 0; ++ } ++ pcd->ep0state = EP0_IDLE; ++ if (doepint.b.setup) { ++ DWC_DEBUGPL(DBG_PCDV, "EP0_IDLE SR=1 setup=1\n"); ++ /* Data stage started, clear setup */ ++ CLEAR_OUT_EP_INTR(core_if, epnum, setup); ++ doepint.b.setup = 0; ++ handle_ep0(pcd); ++ /* Prepare for setup packets if ep0in was enabled*/ ++ if (pcd->ep0state == EP0_IN_STATUS_PHASE) { ++ ep0_out_start(core_if, pcd); ++ } ++ ++ goto exit_xfercompl; ++ } else { ++ /* Prepare for more setup packets */ ++ DWC_DEBUGPL(DBG_PCDV, ++ "EP0_IDLE SR=1 setup=0 new setup comes 2\n"); ++ ep0_out_start(core_if, pcd); ++ } ++ } ++ } ++ } ++ if (core_if->snpsid >= OTG_CORE_REV_2_94a && core_if->dma_enable ++ && core_if->dma_desc_enable == 0) { ++ doepint_data_t doepint_temp = {.d32 = 0}; ++ deptsiz0_data_t doeptsize0 = {.d32 = 0 }; ++ doepint_temp.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ out_ep_regs[ep->dwc_ep.num]->doepint); ++ doeptsize0.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ out_ep_regs[ep->dwc_ep.num]->doeptsiz); ++ if (pcd->ep0state == EP0_IDLE) { ++ if (doepint_temp.b.sr) { ++ CLEAR_OUT_EP_INTR(core_if, epnum, sr); ++ } ++ doepint.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ out_ep_regs[0]->doepint); ++ if (doeptsize0.b.supcnt == 3) { ++ DWC_DEBUGPL(DBG_ANY, "Rolling over!!!!!!!\n"); ++ ep->dwc_ep.stp_rollover = 1; ++ } ++ if (doepint.b.setup) { ++retry: ++ /* Already started data stage, clear setup */ ++ CLEAR_OUT_EP_INTR(core_if, epnum, setup); ++ doepint.b.setup = 0; ++ handle_ep0(pcd); ++ ep->dwc_ep.stp_rollover = 0; ++ /* Prepare for more setup packets */ ++ if (pcd->ep0state == EP0_IN_STATUS_PHASE || ++ pcd->ep0state == EP0_IN_DATA_PHASE) { ++ ep0_out_start(core_if, pcd); ++ } ++ goto exit_xfercompl; ++ } else { ++ /* Prepare for more setup packets */ ++ DWC_DEBUGPL(DBG_ANY, ++ "EP0_IDLE SR=1 setup=0 new setup comes\n"); ++ doepint.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ out_ep_regs[0]->doepint); ++ if(doepint.b.setup) ++ goto retry; ++ ep0_out_start(core_if, pcd); ++ } ++ } else { ++ dwc_otg_pcd_request_t *req; ++ diepint_data_t diepint0 = {.d32 = 0}; ++ doepint_data_t doepint_temp = {.d32 = 0}; ++ depctl_data_t diepctl0; ++ diepint0.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ in_ep_regs[0]->diepint); ++ diepctl0.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ in_ep_regs[0]->diepctl); ++ ++ if (pcd->ep0state == EP0_IN_DATA_PHASE ++ || pcd->ep0state == EP0_IN_STATUS_PHASE) { ++ if (diepint0.b.xfercompl) { ++ DWC_WRITE_REG32(&core_if->dev_if-> ++ in_ep_regs[0]->diepint, diepint0.d32); ++ } ++ if (diepctl0.b.epena) { ++ diepint_data_t diepint = {.d32 = 0}; ++ diepctl0.b.snak = 1; ++ DWC_WRITE_REG32(&core_if->dev_if-> ++ in_ep_regs[0]->diepctl, diepctl0.d32); ++ do { ++ dwc_udelay(10); ++ diepint.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ in_ep_regs[0]->diepint); ++ } while (!diepint.b.inepnakeff); ++ diepint.b.inepnakeff = 1; ++ DWC_WRITE_REG32(&core_if->dev_if-> ++ in_ep_regs[0]->diepint, diepint.d32); ++ diepctl0.d32 = 0; ++ diepctl0.b.epdis = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[0]->diepctl, ++ diepctl0.d32); ++ do { ++ dwc_udelay(10); ++ diepint.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ in_ep_regs[0]->diepint); ++ } while (!diepint.b.epdisabled); ++ diepint.b.epdisabled = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->in_ep_regs[0]->diepint, ++ diepint.d32); ++ } ++ } ++ doepint_temp.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ out_ep_regs[ep->dwc_ep.num]->doepint); ++ if (doepint_temp.b.sr) { ++ CLEAR_OUT_EP_INTR(core_if, epnum, sr); ++ if (DWC_CIRCLEQ_EMPTY(&ep->queue)) { ++ DWC_DEBUGPL(DBG_PCDV, "Request queue empty!!\n"); ++ } else { ++ DWC_DEBUGPL(DBG_PCDV, "complete req!!\n"); ++ req = DWC_CIRCLEQ_FIRST(&ep->queue); ++ if (ep->dwc_ep.xfer_count != ep->dwc_ep.total_len && ++ pcd->ep0state == EP0_OUT_DATA_PHASE) { ++ /* Read arrived setup packet from req->buf */ ++ dwc_memcpy(&pcd->setup_pkt->req, ++ req->buf + ep->dwc_ep.xfer_count, 8); ++ } ++ req->actual = ep->dwc_ep.xfer_count; ++ dwc_otg_request_done(ep, req, -ECONNRESET); ++ ep->dwc_ep.start_xfer_buff = 0; ++ ep->dwc_ep.xfer_buff = 0; ++ ep->dwc_ep.xfer_len = 0; ++ } ++ pcd->ep0state = EP0_IDLE; ++ if (doepint.b.setup) { ++ DWC_DEBUGPL(DBG_PCDV, "EP0_IDLE SR=1 setup=1\n"); ++ /* Data stage started, clear setup */ ++ CLEAR_OUT_EP_INTR(core_if, epnum, setup); ++ doepint.b.setup = 0; ++ handle_ep0(pcd); ++ /* Prepare for setup packets if ep0in was enabled*/ ++ if (pcd->ep0state == EP0_IN_STATUS_PHASE) { ++ ep0_out_start(core_if, pcd); ++ } ++ goto exit_xfercompl; ++ } else { ++ /* Prepare for more setup packets */ ++ DWC_DEBUGPL(DBG_PCDV, ++ "EP0_IDLE SR=1 setup=0 new setup comes 2\n"); ++ ep0_out_start(core_if, pcd); ++ } ++ } ++ } ++ } ++ if (core_if->dma_enable == 0 || pcd->ep0state != EP0_IDLE) ++ handle_ep0(pcd); ++exit_xfercompl: ++ DWC_DEBUGPL(DBG_PCDV, "DOEPINT=%x doepint=%x\n", ++ dwc_otg_read_dev_out_ep_intr(core_if, dwc_ep), doepint.d32); ++ } else { ++ if (core_if->dma_desc_enable == 0 ++ || pcd->ep0state != EP0_IDLE) ++ handle_ep0(pcd); ++ } ++#ifdef DWC_EN_ISOC ++ } else if (dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) { ++ if (doepint.b.pktdrpsts == 0) { ++ /* Clear the bit in DOEPINTn for this interrupt */ ++ CLEAR_OUT_EP_INTR(core_if, ++ epnum, ++ xfercompl); ++ complete_iso_ep(pcd, ep); ++ } else { ++ ++ doepint_data_t doepint = {.d32 = 0 }; ++ doepint.b.xfercompl = 1; ++ doepint.b.pktdrpsts = 1; ++ DWC_WRITE_REG32 ++ (&core_if->dev_if->out_ep_regs ++ [epnum]->doepint, ++ doepint.d32); ++ if (handle_iso_out_pkt_dropped ++ (core_if, dwc_ep)) { ++ complete_iso_ep(pcd, ++ ep); ++ } ++ } ++#endif /* DWC_EN_ISOC */ ++#ifdef DWC_UTE_PER_IO ++ } else if (dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) { ++ CLEAR_OUT_EP_INTR(core_if, epnum, xfercompl); ++ if (!ep->stopped) ++ complete_xiso_ep(ep); ++#endif /* DWC_UTE_PER_IO */ ++ } else { ++ /* Clear the bit in DOEPINTn for this interrupt */ ++ CLEAR_OUT_EP_INTR(core_if, epnum, ++ xfercompl); ++ ++ if (core_if->core_params->dev_out_nak) { ++ DWC_TIMER_CANCEL(pcd->core_if->ep_xfer_timer[epnum]); ++ pcd->core_if->ep_xfer_info[epnum].state = 0; ++#ifdef DEBUG ++ print_memory_payload(pcd, dwc_ep); ++#endif ++ } ++ complete_ep(ep); ++ } ++ ++ } ++ ++ /* Endpoint disable */ ++ if (doepint.b.epdisabled) { ++ ++ /* Clear the bit in DOEPINTn for this interrupt */ ++ CLEAR_OUT_EP_INTR(core_if, epnum, epdisabled); ++ if (core_if->core_params->dev_out_nak) { ++#ifdef DEBUG ++ print_memory_payload(pcd, dwc_ep); ++#endif ++ /* In case of timeout condition */ ++ if (core_if->ep_xfer_info[epnum].state == 2) { ++ dctl.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ dev_global_regs->dctl); ++ dctl.b.cgoutnak = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl, ++ dctl.d32); ++ /* Unmask goutnakeff interrupt which was masked ++ * during handle nak out interrupt */ ++ gintmsk.b.goutnakeff = 1; ++ DWC_MODIFY_REG32(&core_if->core_global_regs->gintmsk, ++ 0, gintmsk.d32); ++ ++ complete_ep(ep); ++ } ++ } ++ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) ++ { ++ dctl_data_t dctl; ++ gintmsk_data_t intr_mask = {.d32 = 0}; ++ dwc_otg_pcd_request_t *req = 0; ++ ++ dctl.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ dev_global_regs->dctl); ++ dctl.b.cgoutnak = 1; ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl, ++ dctl.d32); ++ ++ intr_mask.d32 = 0; ++ intr_mask.b.incomplisoout = 1; ++ ++ /* Get any pending requests */ ++ if (!DWC_CIRCLEQ_EMPTY(&ep->queue)) { ++ req = DWC_CIRCLEQ_FIRST(&ep->queue); ++ if (!req) { ++ DWC_PRINTF("complete_ep 0x%p, req = NULL!\n", ep); ++ } else { ++ dwc_otg_request_done(ep, req, 0); ++ start_next_request(ep); ++ } ++ } else { ++ DWC_PRINTF("complete_ep 0x%p, ep->queue empty!\n", ep); ++ } ++ } ++ } ++ /* AHB Error */ ++ if (doepint.b.ahberr) { ++ DWC_ERROR("EP%d OUT AHB Error\n", epnum); ++ DWC_ERROR("EP%d DEPDMA=0x%08x \n", ++ epnum, core_if->dev_if->out_ep_regs[epnum]->doepdma); ++ CLEAR_OUT_EP_INTR(core_if, epnum, ahberr); ++ } ++ /* Setup Phase Done (contorl EPs) */ ++ if (doepint.b.setup) { ++#ifdef DEBUG_EP0 ++ DWC_DEBUGPL(DBG_PCD, "EP%d SETUP Done\n", epnum); ++#endif ++ CLEAR_OUT_EP_INTR(core_if, epnum, setup); ++ ++ handle_ep0(pcd); ++ } ++ ++ /** OUT EP BNA Intr */ ++ if (doepint.b.bna) { ++ CLEAR_OUT_EP_INTR(core_if, epnum, bna); ++ if (core_if->dma_desc_enable) { ++#ifdef DWC_EN_ISOC ++ if (dwc_ep->type == ++ DWC_OTG_EP_TYPE_ISOC) { ++ /* ++ * This checking is performed to prevent first "false" BNA ++ * handling occuring right after reconnect ++ */ ++ if (dwc_ep->next_frame != ++ 0xffffffff) ++ dwc_otg_pcd_handle_iso_bna(ep); ++ } else ++#endif /* DWC_EN_ISOC */ ++ { ++ dwc_otg_pcd_handle_noniso_bna(ep); ++ } ++ } ++ } ++ /* Babble Interrupt */ ++ if (doepint.b.babble) { ++ DWC_DEBUGPL(DBG_ANY, "EP%d OUT Babble\n", ++ epnum); ++ handle_out_ep_babble_intr(pcd, epnum); ++ ++ CLEAR_OUT_EP_INTR(core_if, epnum, babble); ++ } ++ if (doepint.b.outtknepdis) { ++ DWC_DEBUGPL(DBG_ANY, "EP%d OUT Token received when EP is \ ++ disabled\n",epnum); ++ if (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) { ++ doepmsk_data_t doepmsk = {.d32 = 0}; ++ ep->dwc_ep.frame_num = core_if->frame_num; ++ if (ep->dwc_ep.bInterval > 1) { ++ depctl_data_t depctl; ++ depctl.d32 = DWC_READ_REG32(&core_if->dev_if-> ++ out_ep_regs[epnum]->doepctl); ++ if (ep->dwc_ep.frame_num & 0x1) { ++ depctl.b.setd1pid = 1; ++ depctl.b.setd0pid = 0; ++ } else { ++ depctl.b.setd0pid = 1; ++ depctl.b.setd1pid = 0; ++ } ++ DWC_WRITE_REG32(&core_if->dev_if-> ++ out_ep_regs[epnum]->doepctl, depctl.d32); ++ } ++ start_next_request(ep); ++ doepmsk.b.outtknepdis = 1; ++ DWC_MODIFY_REG32(&core_if->dev_if->dev_global_regs->doepmsk, ++ doepmsk.d32, 0); ++ } ++ CLEAR_OUT_EP_INTR(core_if, epnum, outtknepdis); ++ } ++ ++ /* NAK Interrutp */ ++ if (doepint.b.nak) { ++ DWC_DEBUGPL(DBG_ANY, "EP%d OUT NAK\n", epnum); ++ handle_out_ep_nak_intr(pcd, epnum); ++ ++ CLEAR_OUT_EP_INTR(core_if, epnum, nak); ++ } ++ /* NYET Interrutp */ ++ if (doepint.b.nyet) { ++ DWC_DEBUGPL(DBG_ANY, "EP%d OUT NYET\n", epnum); ++ handle_out_ep_nyet_intr(pcd, epnum); ++ ++ CLEAR_OUT_EP_INTR(core_if, epnum, nyet); ++ } ++ } ++ ++ epnum++; ++ ep_intr >>= 1; ++ } ++ ++ return 1; ++ ++#undef CLEAR_OUT_EP_INTR ++} ++static int drop_transfer(uint32_t trgt_fr, uint32_t curr_fr, uint8_t frm_overrun) ++{ ++ int retval = 0; ++ if(!frm_overrun && curr_fr >= trgt_fr) ++ retval = 1; ++ else if (frm_overrun ++ && (curr_fr >= trgt_fr && ((curr_fr - trgt_fr) < 0x3FFF / 2))) ++ retval = 1; ++ return retval; ++} ++/** ++ * Incomplete ISO IN Transfer Interrupt. ++ * This interrupt indicates one of the following conditions occurred ++ * while transmitting an ISOC transaction. ++ * - Corrupted IN Token for ISOC EP. ++ * - Packet not complete in FIFO. ++ * The follow actions will be taken: ++ * -# Determine the EP ++ * -# Set incomplete flag in dwc_ep structure ++ * -# Disable EP; when "Endpoint Disabled" interrupt is received ++ * Flush FIFO ++ */ ++int32_t dwc_otg_pcd_handle_incomplete_isoc_in_intr(dwc_otg_pcd_t * pcd) ++{ ++ gintsts_data_t gintsts; ++ ++#ifdef DWC_EN_ISOC ++ dwc_otg_dev_if_t *dev_if; ++ deptsiz_data_t deptsiz = {.d32 = 0 }; ++ depctl_data_t depctl = {.d32 = 0 }; ++ dsts_data_t dsts = {.d32 = 0 }; ++ dwc_ep_t *dwc_ep; ++ int i; ++ ++ dev_if = GET_CORE_IF(pcd)->dev_if; ++ ++ for (i = 1; i <= dev_if->num_in_eps; ++i) { ++ dwc_ep = &pcd->in_ep[i].dwc_ep; ++ if (dwc_ep->active && dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) { ++ deptsiz.d32 = ++ DWC_READ_REG32(&dev_if->in_ep_regs[i]->dieptsiz); ++ depctl.d32 = ++ DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl); ++ ++ if (depctl.b.epdis && deptsiz.d32) { ++ set_current_pkt_info(GET_CORE_IF(pcd), dwc_ep); ++ if (dwc_ep->cur_pkt >= dwc_ep->pkt_cnt) { ++ dwc_ep->cur_pkt = 0; ++ dwc_ep->proc_buf_num = ++ (dwc_ep->proc_buf_num ^ 1) & 0x1; ++ ++ if (dwc_ep->proc_buf_num) { ++ dwc_ep->cur_pkt_addr = ++ dwc_ep->xfer_buff1; ++ dwc_ep->cur_pkt_dma_addr = ++ dwc_ep->dma_addr1; ++ } else { ++ dwc_ep->cur_pkt_addr = ++ dwc_ep->xfer_buff0; ++ dwc_ep->cur_pkt_dma_addr = ++ dwc_ep->dma_addr0; ++ } ++ ++ } ++ ++ dsts.d32 = ++ DWC_READ_REG32(&GET_CORE_IF(pcd)->dev_if-> ++ dev_global_regs->dsts); ++ dwc_ep->next_frame = dsts.b.soffn; ++ ++ dwc_otg_iso_ep_start_frm_transfer(GET_CORE_IF ++ (pcd), ++ dwc_ep); ++ } ++ } ++ } ++ ++#else ++ depctl_data_t depctl = {.d32 = 0 }; ++ dwc_ep_t *dwc_ep; ++ dwc_otg_dev_if_t *dev_if; ++ int i; ++ dev_if = GET_CORE_IF(pcd)->dev_if; ++ ++ DWC_DEBUGPL(DBG_PCD,"Incomplete ISO IN \n"); ++ ++ for (i = 1; i <= dev_if->num_in_eps; ++i) { ++ dwc_ep = &pcd->in_ep[i-1].dwc_ep; ++ depctl.d32 = ++ DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl); ++ if (depctl.b.epena && dwc_ep->type == DWC_OTG_EP_TYPE_ISOC) { ++ if (drop_transfer(dwc_ep->frame_num, GET_CORE_IF(pcd)->frame_num, ++ dwc_ep->frm_overrun)) ++ { ++ depctl.d32 = ++ DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl); ++ depctl.b.snak = 1; ++ depctl.b.epdis = 1; ++ DWC_MODIFY_REG32(&dev_if->in_ep_regs[i]->diepctl, depctl.d32, depctl.d32); ++ } ++ } ++ } ++ ++ /*intr_mask.b.incomplisoin = 1; ++ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk, ++ intr_mask.d32, 0); */ ++#endif //DWC_EN_ISOC ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.incomplisoin = 1; ++ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts, ++ gintsts.d32); ++ ++ return 1; ++} ++ ++/** ++ * Incomplete ISO OUT Transfer Interrupt. ++ * ++ * This interrupt indicates that the core has dropped an ISO OUT ++ * packet. The following conditions can be the cause: ++ * - FIFO Full, the entire packet would not fit in the FIFO. ++ * - CRC Error ++ * - Corrupted Token ++ * The follow actions will be taken: ++ * -# Determine the EP ++ * -# Set incomplete flag in dwc_ep structure ++ * -# Read any data from the FIFO ++ * -# Disable EP. When "Endpoint Disabled" interrupt is received ++ * re-enable EP. ++ */ ++int32_t dwc_otg_pcd_handle_incomplete_isoc_out_intr(dwc_otg_pcd_t * pcd) ++{ ++ ++ gintsts_data_t gintsts; ++ ++#ifdef DWC_EN_ISOC ++ dwc_otg_dev_if_t *dev_if; ++ deptsiz_data_t deptsiz = {.d32 = 0 }; ++ depctl_data_t depctl = {.d32 = 0 }; ++ dsts_data_t dsts = {.d32 = 0 }; ++ dwc_ep_t *dwc_ep; ++ int i; ++ ++ dev_if = GET_CORE_IF(pcd)->dev_if; ++ ++ for (i = 1; i <= dev_if->num_out_eps; ++i) { ++ dwc_ep = &pcd->in_ep[i].dwc_ep; ++ if (pcd->out_ep[i].dwc_ep.active && ++ pcd->out_ep[i].dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) { ++ deptsiz.d32 = ++ DWC_READ_REG32(&dev_if->out_ep_regs[i]->doeptsiz); ++ depctl.d32 = ++ DWC_READ_REG32(&dev_if->out_ep_regs[i]->doepctl); ++ ++ if (depctl.b.epdis && deptsiz.d32) { ++ set_current_pkt_info(GET_CORE_IF(pcd), ++ &pcd->out_ep[i].dwc_ep); ++ if (dwc_ep->cur_pkt >= dwc_ep->pkt_cnt) { ++ dwc_ep->cur_pkt = 0; ++ dwc_ep->proc_buf_num = ++ (dwc_ep->proc_buf_num ^ 1) & 0x1; ++ ++ if (dwc_ep->proc_buf_num) { ++ dwc_ep->cur_pkt_addr = ++ dwc_ep->xfer_buff1; ++ dwc_ep->cur_pkt_dma_addr = ++ dwc_ep->dma_addr1; ++ } else { ++ dwc_ep->cur_pkt_addr = ++ dwc_ep->xfer_buff0; ++ dwc_ep->cur_pkt_dma_addr = ++ dwc_ep->dma_addr0; ++ } ++ ++ } ++ ++ dsts.d32 = ++ DWC_READ_REG32(&GET_CORE_IF(pcd)->dev_if-> ++ dev_global_regs->dsts); ++ dwc_ep->next_frame = dsts.b.soffn; ++ ++ dwc_otg_iso_ep_start_frm_transfer(GET_CORE_IF ++ (pcd), ++ dwc_ep); ++ } ++ } ++ } ++#else ++ /** @todo implement ISR */ ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ dwc_otg_core_if_t *core_if; ++ deptsiz_data_t deptsiz = {.d32 = 0 }; ++ depctl_data_t depctl = {.d32 = 0 }; ++ dctl_data_t dctl = {.d32 = 0 }; ++ dwc_ep_t *dwc_ep = NULL; ++ int i; ++ core_if = GET_CORE_IF(pcd); ++ ++ for (i = 0; i < core_if->dev_if->num_out_eps; ++i) { ++ dwc_ep = &pcd->out_ep[i].dwc_ep; ++ depctl.d32 = ++ DWC_READ_REG32(&core_if->dev_if->out_ep_regs[dwc_ep->num]->doepctl); ++ if (depctl.b.epena && depctl.b.dpid == (core_if->frame_num & 0x1)) { ++ core_if->dev_if->isoc_ep = dwc_ep; ++ deptsiz.d32 = ++ DWC_READ_REG32(&core_if->dev_if->out_ep_regs[dwc_ep->num]->doeptsiz); ++ break; ++ } ++ } ++ dctl.d32 = DWC_READ_REG32(&core_if->dev_if->dev_global_regs->dctl); ++ gintsts.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintsts); ++ intr_mask.d32 = DWC_READ_REG32(&core_if->core_global_regs->gintmsk); ++ ++ if (!intr_mask.b.goutnakeff) { ++ /* Unmask it */ ++ intr_mask.b.goutnakeff = 1; ++ DWC_WRITE_REG32(&core_if->core_global_regs->gintmsk, intr_mask.d32); ++ } ++ if (!gintsts.b.goutnakeff) { ++ dctl.b.sgoutnak = 1; ++ } ++ DWC_WRITE_REG32(&core_if->dev_if->dev_global_regs->dctl, dctl.d32); ++ ++ depctl.d32 = DWC_READ_REG32(&core_if->dev_if->out_ep_regs[dwc_ep->num]->doepctl); ++ if (depctl.b.epena) { ++ depctl.b.epdis = 1; ++ depctl.b.snak = 1; ++ } ++ DWC_WRITE_REG32(&core_if->dev_if->out_ep_regs[dwc_ep->num]->doepctl, depctl.d32); ++ ++ intr_mask.d32 = 0; ++ intr_mask.b.incomplisoout = 1; ++ ++#endif /* DWC_EN_ISOC */ ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.incomplisoout = 1; ++ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts, ++ gintsts.d32); ++ ++ return 1; ++} ++ ++/** ++ * This function handles the Global IN NAK Effective interrupt. ++ * ++ */ ++int32_t dwc_otg_pcd_handle_in_nak_effective(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_dev_if_t *dev_if = GET_CORE_IF(pcd)->dev_if; ++ depctl_data_t diepctl = {.d32 = 0 }; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ gintsts_data_t gintsts; ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++ int i; ++ ++ DWC_DEBUGPL(DBG_PCD, "Global IN NAK Effective\n"); ++ ++ /* Disable all active IN EPs */ ++ for (i = 0; i <= dev_if->num_in_eps; i++) { ++ diepctl.d32 = DWC_READ_REG32(&dev_if->in_ep_regs[i]->diepctl); ++ if (!(diepctl.b.eptype & 1) && diepctl.b.epena) { ++ if (core_if->start_predict > 0) ++ core_if->start_predict++; ++ diepctl.b.epdis = 1; ++ diepctl.b.snak = 1; ++ DWC_WRITE_REG32(&dev_if->in_ep_regs[i]->diepctl, diepctl.d32); ++ } ++ } ++ ++ ++ /* Disable the Global IN NAK Effective Interrupt */ ++ intr_mask.b.ginnakeff = 1; ++ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk, ++ intr_mask.d32, 0); ++ ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.ginnakeff = 1; ++ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts, ++ gintsts.d32); ++ ++ return 1; ++} ++ ++/** ++ * OUT NAK Effective. ++ * ++ */ ++int32_t dwc_otg_pcd_handle_out_nak_effective(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_dev_if_t *dev_if = GET_CORE_IF(pcd)->dev_if; ++ gintmsk_data_t intr_mask = {.d32 = 0 }; ++ gintsts_data_t gintsts; ++ depctl_data_t doepctl; ++ int i; ++ ++ /* Disable the Global OUT NAK Effective Interrupt */ ++ intr_mask.b.goutnakeff = 1; ++ DWC_MODIFY_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintmsk, ++ intr_mask.d32, 0); ++ ++ /* If DEV OUT NAK enabled*/ ++ if (pcd->core_if->core_params->dev_out_nak) { ++ /* Run over all out endpoints to determine the ep number on ++ * which the timeout has happened ++ */ ++ for (i = 0; i <= dev_if->num_out_eps; i++) { ++ if ( pcd->core_if->ep_xfer_info[i].state == 2 ) ++ break; ++ } ++ if (i > dev_if->num_out_eps) { ++ dctl_data_t dctl; ++ dctl.d32 = ++ DWC_READ_REG32(&dev_if->dev_global_regs->dctl); ++ dctl.b.cgoutnak = 1; ++ DWC_WRITE_REG32(&dev_if->dev_global_regs->dctl, ++ dctl.d32); ++ goto out; ++ } ++ ++ /* Disable the endpoint */ ++ doepctl.d32 = DWC_READ_REG32(&dev_if->out_ep_regs[i]->doepctl); ++ if (doepctl.b.epena) { ++ doepctl.b.epdis = 1; ++ doepctl.b.snak = 1; ++ } ++ DWC_WRITE_REG32(&dev_if->out_ep_regs[i]->doepctl, doepctl.d32); ++ return 1; ++ } ++ /* We come here from Incomplete ISO OUT handler */ ++ if (dev_if->isoc_ep) { ++ dwc_ep_t *dwc_ep = (dwc_ep_t *)dev_if->isoc_ep; ++ uint32_t epnum = dwc_ep->num; ++ doepint_data_t doepint; ++ doepint.d32 = ++ DWC_READ_REG32(&dev_if->out_ep_regs[dwc_ep->num]->doepint); ++ dev_if->isoc_ep = NULL; ++ doepctl.d32 = ++ DWC_READ_REG32(&dev_if->out_ep_regs[epnum]->doepctl); ++ DWC_PRINTF("Before disable DOEPCTL = %08x\n", doepctl.d32); ++ if (doepctl.b.epena) { ++ doepctl.b.epdis = 1; ++ doepctl.b.snak = 1; ++ } ++ DWC_WRITE_REG32(&dev_if->out_ep_regs[epnum]->doepctl, ++ doepctl.d32); ++ return 1; ++ } else ++ DWC_PRINTF("INTERRUPT Handler not implemented for %s\n", ++ "Global OUT NAK Effective\n"); ++ ++out: ++ /* Clear interrupt */ ++ gintsts.d32 = 0; ++ gintsts.b.goutnakeff = 1; ++ DWC_WRITE_REG32(&GET_CORE_IF(pcd)->core_global_regs->gintsts, ++ gintsts.d32); ++ ++ return 1; ++} ++ ++/** ++ * PCD interrupt handler. ++ * ++ * The PCD handles the device interrupts. Many conditions can cause a ++ * device interrupt. When an interrupt occurs, the device interrupt ++ * service routine determines the cause of the interrupt and ++ * dispatches handling to the appropriate function. These interrupt ++ * handling functions are described below. ++ * ++ * All interrupt registers are processed from LSB to MSB. ++ * ++ */ ++int32_t dwc_otg_pcd_handle_intr(dwc_otg_pcd_t * pcd) ++{ ++ dwc_otg_core_if_t *core_if = GET_CORE_IF(pcd); ++#ifdef VERBOSE ++ dwc_otg_core_global_regs_t *global_regs = core_if->core_global_regs; ++#endif ++ gintsts_data_t gintr_status; ++ int32_t retval = 0; ++ ++ /* Exit from ISR if core is hibernated */ ++ if (core_if->hibernation_suspend == 1) { ++ return retval; ++ } ++#ifdef VERBOSE ++ DWC_DEBUGPL(DBG_ANY, "%s() gintsts=%08x gintmsk=%08x\n", ++ __func__, ++ DWC_READ_REG32(&global_regs->gintsts), ++ DWC_READ_REG32(&global_regs->gintmsk)); ++#endif ++ ++ if (dwc_otg_is_device_mode(core_if)) { ++ DWC_SPINLOCK(pcd->lock); ++#ifdef VERBOSE ++ DWC_DEBUGPL(DBG_PCDV, "%s() gintsts=%08x gintmsk=%08x\n", ++ __func__, ++ DWC_READ_REG32(&global_regs->gintsts), ++ DWC_READ_REG32(&global_regs->gintmsk)); ++#endif ++ ++ gintr_status.d32 = dwc_otg_read_core_intr(core_if); ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s: gintsts&gintmsk=%08x\n", ++ __func__, gintr_status.d32); ++ ++ if (gintr_status.b.sofintr) { ++ retval |= dwc_otg_pcd_handle_sof_intr(pcd); ++ } ++ if (gintr_status.b.rxstsqlvl) { ++ retval |= ++ dwc_otg_pcd_handle_rx_status_q_level_intr(pcd); ++ } ++ if (gintr_status.b.nptxfempty) { ++ retval |= dwc_otg_pcd_handle_np_tx_fifo_empty_intr(pcd); ++ } ++ if (gintr_status.b.goutnakeff) { ++ retval |= dwc_otg_pcd_handle_out_nak_effective(pcd); ++ } ++ if (gintr_status.b.i2cintr) { ++ retval |= dwc_otg_pcd_handle_i2c_intr(pcd); ++ } ++ if (gintr_status.b.erlysuspend) { ++ retval |= dwc_otg_pcd_handle_early_suspend_intr(pcd); ++ } ++ if (gintr_status.b.usbreset) { ++ retval |= dwc_otg_pcd_handle_usb_reset_intr(pcd); ++ } ++ if (gintr_status.b.enumdone) { ++ retval |= dwc_otg_pcd_handle_enum_done_intr(pcd); ++ } ++ if (gintr_status.b.isooutdrop) { ++ retval |= ++ dwc_otg_pcd_handle_isoc_out_packet_dropped_intr ++ (pcd); ++ } ++ if (gintr_status.b.eopframe) { ++ retval |= ++ dwc_otg_pcd_handle_end_periodic_frame_intr(pcd); ++ } ++ if (gintr_status.b.inepint) { ++ if (!core_if->multiproc_int_enable) { ++ retval |= dwc_otg_pcd_handle_in_ep_intr(pcd); ++ } ++ } ++ if (gintr_status.b.outepintr) { ++ if (!core_if->multiproc_int_enable) { ++ retval |= dwc_otg_pcd_handle_out_ep_intr(pcd); ++ } ++ } ++ if (gintr_status.b.epmismatch) { ++ retval |= dwc_otg_pcd_handle_ep_mismatch_intr(pcd); ++ } ++ if (gintr_status.b.fetsusp) { ++ retval |= dwc_otg_pcd_handle_ep_fetsusp_intr(pcd); ++ } ++ if (gintr_status.b.ginnakeff) { ++ retval |= dwc_otg_pcd_handle_in_nak_effective(pcd); ++ } ++ if (gintr_status.b.incomplisoin) { ++ retval |= ++ dwc_otg_pcd_handle_incomplete_isoc_in_intr(pcd); ++ } ++ if (gintr_status.b.incomplisoout) { ++ retval |= ++ dwc_otg_pcd_handle_incomplete_isoc_out_intr(pcd); ++ } ++ ++ /* In MPI mode Device Endpoints interrupts are asserted ++ * without setting outepintr and inepint bits set, so these ++ * Interrupt handlers are called without checking these bit-fields ++ */ ++ if (core_if->multiproc_int_enable) { ++ retval |= dwc_otg_pcd_handle_in_ep_intr(pcd); ++ retval |= dwc_otg_pcd_handle_out_ep_intr(pcd); ++ } ++#ifdef VERBOSE ++ DWC_DEBUGPL(DBG_PCDV, "%s() gintsts=%0x\n", __func__, ++ DWC_READ_REG32(&global_regs->gintsts)); ++#endif ++ DWC_SPINUNLOCK(pcd->lock); ++ } ++ return retval; ++} ++ ++#endif /* DWC_HOST_ONLY */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_pcd_linux.c +@@ -0,0 +1,1262 @@ ++ /* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_pcd_linux.c $ ++ * $Revision: #21 $ ++ * $Date: 2012/08/10 $ ++ * $Change: 2047372 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++#ifndef DWC_HOST_ONLY ++ ++/** @file ++ * This file implements the Peripheral Controller Driver. ++ * ++ * The Peripheral Controller Driver (PCD) is responsible for ++ * translating requests from the Function Driver into the appropriate ++ * actions on the DWC_otg controller. It isolates the Function Driver ++ * from the specifics of the controller by providing an API to the ++ * Function Driver. ++ * ++ * The Peripheral Controller Driver for Linux will implement the ++ * Gadget API, so that the existing Gadget drivers can be used. ++ * (Gadget Driver is the Linux terminology for a Function Driver.) ++ * ++ * The Linux Gadget API is defined in the header file ++ * . The USB EP operations API is ++ * defined in the structure usb_ep_ops and the USB ++ * Controller API is defined in the structure ++ * usb_gadget_ops. ++ * ++ */ ++ ++#include "dwc_otg_os_dep.h" ++#include "dwc_otg_pcd_if.h" ++#include "dwc_otg_pcd.h" ++#include "dwc_otg_driver.h" ++#include "dwc_otg_dbg.h" ++ ++extern bool fiq_enable; ++ ++static struct gadget_wrapper { ++ dwc_otg_pcd_t *pcd; ++ ++ struct usb_gadget gadget; ++ struct usb_gadget_driver *driver; ++ ++ struct usb_ep ep0; ++ struct usb_ep in_ep[16]; ++ struct usb_ep out_ep[16]; ++ ++} *gadget_wrapper; ++ ++/* Display the contents of the buffer */ ++extern void dump_msg(const u8 * buf, unsigned int length); ++/** ++ * Get the dwc_otg_pcd_ep_t* from usb_ep* pointer - NULL in case ++ * if the endpoint is not found ++ */ ++static struct dwc_otg_pcd_ep *ep_from_handle(dwc_otg_pcd_t * pcd, void *handle) ++{ ++ int i; ++ if (pcd->ep0.priv == handle) { ++ return &pcd->ep0; ++ } ++ ++ for (i = 0; i < MAX_EPS_CHANNELS - 1; i++) { ++ if (pcd->in_ep[i].priv == handle) ++ return &pcd->in_ep[i]; ++ if (pcd->out_ep[i].priv == handle) ++ return &pcd->out_ep[i]; ++ } ++ ++ return NULL; ++} ++ ++/* USB Endpoint Operations */ ++/* ++ * The following sections briefly describe the behavior of the Gadget ++ * API endpoint operations implemented in the DWC_otg driver ++ * software. Detailed descriptions of the generic behavior of each of ++ * these functions can be found in the Linux header file ++ * include/linux/usb_gadget.h. ++ * ++ * The Gadget API provides wrapper functions for each of the function ++ * pointers defined in usb_ep_ops. The Gadget Driver calls the wrapper ++ * function, which then calls the underlying PCD function. The ++ * following sections are named according to the wrapper ++ * functions. Within each section, the corresponding DWC_otg PCD ++ * function name is specified. ++ * ++ */ ++ ++/** ++ * This function is called by the Gadget Driver for each EP to be ++ * configured for the current configuration (SET_CONFIGURATION). ++ * ++ * This function initializes the dwc_otg_ep_t data structure, and then ++ * calls dwc_otg_ep_activate. ++ */ ++static int ep_enable(struct usb_ep *usb_ep, ++ const struct usb_endpoint_descriptor *ep_desc) ++{ ++ int retval; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%p)\n", __func__, usb_ep, ep_desc); ++ ++ if (!usb_ep || !ep_desc || ep_desc->bDescriptorType != USB_DT_ENDPOINT) { ++ DWC_WARN("%s, bad ep or descriptor\n", __func__); ++ return -EINVAL; ++ } ++ if (usb_ep == &gadget_wrapper->ep0) { ++ DWC_WARN("%s, bad ep(0)\n", __func__); ++ return -EINVAL; ++ } ++ ++ /* Check FIFO size? */ ++ if (!ep_desc->wMaxPacketSize) { ++ DWC_WARN("%s, bad %s maxpacket\n", __func__, usb_ep->name); ++ return -ERANGE; ++ } ++ ++ if (!gadget_wrapper->driver || ++ gadget_wrapper->gadget.speed == USB_SPEED_UNKNOWN) { ++ DWC_WARN("%s, bogus device state\n", __func__); ++ return -ESHUTDOWN; ++ } ++ ++ /* Delete after check - MAS */ ++#if 0 ++ nat = (uint32_t) ep_desc->wMaxPacketSize; ++ printk(KERN_ALERT "%s: nat (before) =%d\n", __func__, nat); ++ nat = (nat >> 11) & 0x03; ++ printk(KERN_ALERT "%s: nat (after) =%d\n", __func__, nat); ++#endif ++ retval = dwc_otg_pcd_ep_enable(gadget_wrapper->pcd, ++ (const uint8_t *)ep_desc, ++ (void *)usb_ep); ++ if (retval) { ++ DWC_WARN("dwc_otg_pcd_ep_enable failed\n"); ++ return -EINVAL; ++ } ++ ++ usb_ep->maxpacket = le16_to_cpu(ep_desc->wMaxPacketSize); ++ ++ return 0; ++} ++ ++/** ++ * This function is called when an EP is disabled due to disconnect or ++ * change in configuration. Any pending requests will terminate with a ++ * status of -ESHUTDOWN. ++ * ++ * This function modifies the dwc_otg_ep_t data structure for this EP, ++ * and then calls dwc_otg_ep_deactivate. ++ */ ++static int ep_disable(struct usb_ep *usb_ep) ++{ ++ int retval; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, usb_ep); ++ if (!usb_ep) { ++ DWC_DEBUGPL(DBG_PCD, "%s, %s not enabled\n", __func__, ++ usb_ep ? usb_ep->name : NULL); ++ return -EINVAL; ++ } ++ ++ retval = dwc_otg_pcd_ep_disable(gadget_wrapper->pcd, usb_ep); ++ if (retval) { ++ retval = -EINVAL; ++ } ++ ++ return retval; ++} ++ ++/** ++ * This function allocates a request object to use with the specified ++ * endpoint. ++ * ++ * @param ep The endpoint to be used with with the request ++ * @param gfp_flags the GFP_* flags to use. ++ */ ++static struct usb_request *dwc_otg_pcd_alloc_request(struct usb_ep *ep, ++ gfp_t gfp_flags) ++{ ++ struct usb_request *usb_req; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%d)\n", __func__, ep, gfp_flags); ++ if (0 == ep) { ++ DWC_WARN("%s() %s\n", __func__, "Invalid EP!\n"); ++ return 0; ++ } ++ usb_req = kzalloc(sizeof(*usb_req), gfp_flags); ++ if (0 == usb_req) { ++ DWC_WARN("%s() %s\n", __func__, "request allocation failed!\n"); ++ return 0; ++ } ++ usb_req->dma = DWC_DMA_ADDR_INVALID; ++ ++ return usb_req; ++} ++ ++/** ++ * This function frees a request object. ++ * ++ * @param ep The endpoint associated with the request ++ * @param req The request being freed ++ */ ++static void dwc_otg_pcd_free_request(struct usb_ep *ep, struct usb_request *req) ++{ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%p)\n", __func__, ep, req); ++ ++ if (0 == ep || 0 == req) { ++ DWC_WARN("%s() %s\n", __func__, ++ "Invalid ep or req argument!\n"); ++ return; ++ } ++ ++ kfree(req); ++} ++ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28) ++/** ++ * This function allocates an I/O buffer to be used for a transfer ++ * to/from the specified endpoint. ++ * ++ * @param usb_ep The endpoint to be used with with the request ++ * @param bytes The desired number of bytes for the buffer ++ * @param dma Pointer to the buffer's DMA address; must be valid ++ * @param gfp_flags the GFP_* flags to use. ++ * @return address of a new buffer or null is buffer could not be allocated. ++ */ ++static void *dwc_otg_pcd_alloc_buffer(struct usb_ep *usb_ep, unsigned bytes, ++ dma_addr_t * dma, gfp_t gfp_flags) ++{ ++ void *buf; ++ dwc_otg_pcd_t *pcd = 0; ++ ++ pcd = gadget_wrapper->pcd; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%d,%p,%0x)\n", __func__, usb_ep, bytes, ++ dma, gfp_flags); ++ ++ /* Check dword alignment */ ++ if ((bytes & 0x3UL) != 0) { ++ DWC_WARN("%s() Buffer size is not a multiple of" ++ "DWORD size (%d)", __func__, bytes); ++ } ++ ++ buf = dma_alloc_coherent(NULL, bytes, dma, gfp_flags); ++ WARN_ON(!buf); ++ ++ /* Check dword alignment */ ++ if (((int)buf & 0x3UL) != 0) { ++ DWC_WARN("%s() Buffer is not DWORD aligned (%p)", ++ __func__, buf); ++ } ++ ++ return buf; ++} ++ ++/** ++ * This function frees an I/O buffer that was allocated by alloc_buffer. ++ * ++ * @param usb_ep the endpoint associated with the buffer ++ * @param buf address of the buffer ++ * @param dma The buffer's DMA address ++ * @param bytes The number of bytes of the buffer ++ */ ++static void dwc_otg_pcd_free_buffer(struct usb_ep *usb_ep, void *buf, ++ dma_addr_t dma, unsigned bytes) ++{ ++ dwc_otg_pcd_t *pcd = 0; ++ ++ pcd = gadget_wrapper->pcd; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%0x,%d)\n", __func__, buf, dma, bytes); ++ ++ dma_free_coherent(NULL, bytes, buf, dma); ++} ++#endif ++ ++/** ++ * This function is used to submit an I/O Request to an EP. ++ * ++ * - When the request completes the request's completion callback ++ * is called to return the request to the driver. ++ * - An EP, except control EPs, may have multiple requests ++ * pending. ++ * - Once submitted the request cannot be examined or modified. ++ * - Each request is turned into one or more packets. ++ * - A BULK EP can queue any amount of data; the transfer is ++ * packetized. ++ * - Zero length Packets are specified with the request 'zero' ++ * flag. ++ */ ++static int ep_queue(struct usb_ep *usb_ep, struct usb_request *usb_req, ++ gfp_t gfp_flags) ++{ ++ dwc_otg_pcd_t *pcd; ++ struct dwc_otg_pcd_ep *ep = NULL; ++ int retval = 0, is_isoc_ep = 0; ++ dma_addr_t dma_addr = DWC_DMA_ADDR_INVALID; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%p,%d)\n", ++ __func__, usb_ep, usb_req, gfp_flags); ++ ++ if (!usb_req || !usb_req->complete || !usb_req->buf) { ++ DWC_WARN("bad params\n"); ++ return -EINVAL; ++ } ++ ++ if (!usb_ep) { ++ DWC_WARN("bad ep\n"); ++ return -EINVAL; ++ } ++ ++ pcd = gadget_wrapper->pcd; ++ if (!gadget_wrapper->driver || ++ gadget_wrapper->gadget.speed == USB_SPEED_UNKNOWN) { ++ DWC_DEBUGPL(DBG_PCDV, "gadget.speed=%d\n", ++ gadget_wrapper->gadget.speed); ++ DWC_WARN("bogus device state\n"); ++ return -ESHUTDOWN; ++ } ++ ++ DWC_DEBUGPL(DBG_PCD, "%s queue req %p, len %d buf %p\n", ++ usb_ep->name, usb_req, usb_req->length, usb_req->buf); ++ ++ usb_req->status = -EINPROGRESS; ++ usb_req->actual = 0; ++ ++ ep = ep_from_handle(pcd, usb_ep); ++ if (ep == NULL) ++ is_isoc_ep = 0; ++ else ++ is_isoc_ep = (ep->dwc_ep.type == DWC_OTG_EP_TYPE_ISOC) ? 1 : 0; ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28) ++ dma_addr = usb_req->dma; ++#else ++ if (GET_CORE_IF(pcd)->dma_enable) { ++ dwc_otg_device_t *otg_dev = gadget_wrapper->pcd->otg_dev; ++ struct device *dev = NULL; ++ ++ if (otg_dev != NULL) ++ dev = DWC_OTG_OS_GETDEV(otg_dev->os_dep); ++ ++ if (usb_req->length != 0 && ++ usb_req->dma == DWC_DMA_ADDR_INVALID) { ++ dma_addr = dma_map_single(dev, usb_req->buf, ++ usb_req->length, ++ ep->dwc_ep.is_in ? ++ DMA_TO_DEVICE: ++ DMA_FROM_DEVICE); ++ } ++ } ++#endif ++ ++#ifdef DWC_UTE_PER_IO ++ if (is_isoc_ep == 1) { ++ retval = dwc_otg_pcd_xiso_ep_queue(pcd, usb_ep, usb_req->buf, dma_addr, ++ usb_req->length, usb_req->zero, usb_req, ++ gfp_flags == GFP_ATOMIC ? 1 : 0, &usb_req->ext_req); ++ if (retval) ++ return -EINVAL; ++ ++ return 0; ++ } ++#endif ++ retval = dwc_otg_pcd_ep_queue(pcd, usb_ep, usb_req->buf, dma_addr, ++ usb_req->length, usb_req->zero, usb_req, ++ gfp_flags == GFP_ATOMIC ? 1 : 0); ++ if (retval) { ++ return -EINVAL; ++ } ++ ++ return 0; ++} ++ ++/** ++ * This function cancels an I/O request from an EP. ++ */ ++static int ep_dequeue(struct usb_ep *usb_ep, struct usb_request *usb_req) ++{ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p,%p)\n", __func__, usb_ep, usb_req); ++ ++ if (!usb_ep || !usb_req) { ++ DWC_WARN("bad argument\n"); ++ return -EINVAL; ++ } ++ if (!gadget_wrapper->driver || ++ gadget_wrapper->gadget.speed == USB_SPEED_UNKNOWN) { ++ DWC_WARN("bogus device state\n"); ++ return -ESHUTDOWN; ++ } ++ if (dwc_otg_pcd_ep_dequeue(gadget_wrapper->pcd, usb_ep, usb_req)) { ++ return -EINVAL; ++ } ++ ++ return 0; ++} ++ ++/** ++ * usb_ep_set_halt stalls an endpoint. ++ * ++ * usb_ep_clear_halt clears an endpoint halt and resets its data ++ * toggle. ++ * ++ * Both of these functions are implemented with the same underlying ++ * function. The behavior depends on the value argument. ++ * ++ * @param[in] usb_ep the Endpoint to halt or clear halt. ++ * @param[in] value ++ * - 0 means clear_halt. ++ * - 1 means set_halt, ++ * - 2 means clear stall lock flag. ++ * - 3 means set stall lock flag. ++ */ ++static int ep_halt(struct usb_ep *usb_ep, int value) ++{ ++ int retval = 0; ++ ++ DWC_DEBUGPL(DBG_PCD, "HALT %s %d\n", usb_ep->name, value); ++ ++ if (!usb_ep) { ++ DWC_WARN("bad ep\n"); ++ return -EINVAL; ++ } ++ ++ retval = dwc_otg_pcd_ep_halt(gadget_wrapper->pcd, usb_ep, value); ++ if (retval == -DWC_E_AGAIN) { ++ return -EAGAIN; ++ } else if (retval) { ++ retval = -EINVAL; ++ } ++ ++ return retval; ++} ++ ++//#if (LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,30)) ++#if 0 ++/** ++ * ep_wedge: sets the halt feature and ignores clear requests ++ * ++ * @usb_ep: the endpoint being wedged ++ * ++ * Use this to stall an endpoint and ignore CLEAR_FEATURE(HALT_ENDPOINT) ++ * requests. If the gadget driver clears the halt status, it will ++ * automatically unwedge the endpoint. ++ * ++ * Returns zero on success, else negative errno. * ++ * Check usb_ep_set_wedge() at "usb_gadget.h" for details ++ */ ++static int ep_wedge(struct usb_ep *usb_ep) ++{ ++ int retval = 0; ++ ++ DWC_DEBUGPL(DBG_PCD, "WEDGE %s\n", usb_ep->name); ++ ++ if (!usb_ep) { ++ DWC_WARN("bad ep\n"); ++ return -EINVAL; ++ } ++ ++ retval = dwc_otg_pcd_ep_wedge(gadget_wrapper->pcd, usb_ep); ++ if (retval == -DWC_E_AGAIN) { ++ retval = -EAGAIN; ++ } else if (retval) { ++ retval = -EINVAL; ++ } ++ ++ return retval; ++} ++#endif ++ ++#ifdef DWC_EN_ISOC ++/** ++ * This function is used to submit an ISOC Transfer Request to an EP. ++ * ++ * - Every time a sync period completes the request's completion callback ++ * is called to provide data to the gadget driver. ++ * - Once submitted the request cannot be modified. ++ * - Each request is turned into periodic data packets untill ISO ++ * Transfer is stopped.. ++ */ ++static int iso_ep_start(struct usb_ep *usb_ep, struct usb_iso_request *req, ++ gfp_t gfp_flags) ++{ ++ int retval = 0; ++ ++ if (!req || !req->process_buffer || !req->buf0 || !req->buf1) { ++ DWC_WARN("bad params\n"); ++ return -EINVAL; ++ } ++ ++ if (!usb_ep) { ++ DWC_PRINTF("bad params\n"); ++ return -EINVAL; ++ } ++ ++ req->status = -EINPROGRESS; ++ ++ retval = ++ dwc_otg_pcd_iso_ep_start(gadget_wrapper->pcd, usb_ep, req->buf0, ++ req->buf1, req->dma0, req->dma1, ++ req->sync_frame, req->data_pattern_frame, ++ req->data_per_frame, ++ req-> ++ flags & USB_REQ_ISO_ASAP ? -1 : ++ req->start_frame, req->buf_proc_intrvl, ++ req, gfp_flags == GFP_ATOMIC ? 1 : 0); ++ ++ if (retval) { ++ return -EINVAL; ++ } ++ ++ return retval; ++} ++ ++/** ++ * This function stops ISO EP Periodic Data Transfer. ++ */ ++static int iso_ep_stop(struct usb_ep *usb_ep, struct usb_iso_request *req) ++{ ++ int retval = 0; ++ if (!usb_ep) { ++ DWC_WARN("bad ep\n"); ++ } ++ ++ if (!gadget_wrapper->driver || ++ gadget_wrapper->gadget.speed == USB_SPEED_UNKNOWN) { ++ DWC_DEBUGPL(DBG_PCDV, "gadget.speed=%d\n", ++ gadget_wrapper->gadget.speed); ++ DWC_WARN("bogus device state\n"); ++ } ++ ++ dwc_otg_pcd_iso_ep_stop(gadget_wrapper->pcd, usb_ep, req); ++ if (retval) { ++ retval = -EINVAL; ++ } ++ ++ return retval; ++} ++ ++static struct usb_iso_request *alloc_iso_request(struct usb_ep *ep, ++ int packets, gfp_t gfp_flags) ++{ ++ struct usb_iso_request *pReq = NULL; ++ uint32_t req_size; ++ ++ req_size = sizeof(struct usb_iso_request); ++ req_size += ++ (2 * packets * (sizeof(struct usb_gadget_iso_packet_descriptor))); ++ ++ pReq = kmalloc(req_size, gfp_flags); ++ if (!pReq) { ++ DWC_WARN("Can't allocate Iso Request\n"); ++ return 0; ++ } ++ pReq->iso_packet_desc0 = (void *)(pReq + 1); ++ ++ pReq->iso_packet_desc1 = pReq->iso_packet_desc0 + packets; ++ ++ return pReq; ++} ++ ++static void free_iso_request(struct usb_ep *ep, struct usb_iso_request *req) ++{ ++ kfree(req); ++} ++ ++static struct usb_isoc_ep_ops dwc_otg_pcd_ep_ops = { ++ .ep_ops = { ++ .enable = ep_enable, ++ .disable = ep_disable, ++ ++ .alloc_request = dwc_otg_pcd_alloc_request, ++ .free_request = dwc_otg_pcd_free_request, ++ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28) ++ .alloc_buffer = dwc_otg_pcd_alloc_buffer, ++ .free_buffer = dwc_otg_pcd_free_buffer, ++#endif ++ ++ .queue = ep_queue, ++ .dequeue = ep_dequeue, ++ ++ .set_halt = ep_halt, ++ .fifo_status = 0, ++ .fifo_flush = 0, ++ }, ++ .iso_ep_start = iso_ep_start, ++ .iso_ep_stop = iso_ep_stop, ++ .alloc_iso_request = alloc_iso_request, ++ .free_iso_request = free_iso_request, ++}; ++ ++#else ++ ++ int (*enable) (struct usb_ep *ep, ++ const struct usb_endpoint_descriptor *desc); ++ int (*disable) (struct usb_ep *ep); ++ ++ struct usb_request *(*alloc_request) (struct usb_ep *ep, ++ gfp_t gfp_flags); ++ void (*free_request) (struct usb_ep *ep, struct usb_request *req); ++ ++ int (*queue) (struct usb_ep *ep, struct usb_request *req, ++ gfp_t gfp_flags); ++ int (*dequeue) (struct usb_ep *ep, struct usb_request *req); ++ ++ int (*set_halt) (struct usb_ep *ep, int value); ++ int (*set_wedge) (struct usb_ep *ep); ++ ++ int (*fifo_status) (struct usb_ep *ep); ++ void (*fifo_flush) (struct usb_ep *ep); ++static struct usb_ep_ops dwc_otg_pcd_ep_ops = { ++ .enable = ep_enable, ++ .disable = ep_disable, ++ ++ .alloc_request = dwc_otg_pcd_alloc_request, ++ .free_request = dwc_otg_pcd_free_request, ++ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,28) ++ .alloc_buffer = dwc_otg_pcd_alloc_buffer, ++ .free_buffer = dwc_otg_pcd_free_buffer, ++#else ++ /* .set_wedge = ep_wedge, */ ++ .set_wedge = NULL, /* uses set_halt instead */ ++#endif ++ ++ .queue = ep_queue, ++ .dequeue = ep_dequeue, ++ ++ .set_halt = ep_halt, ++ .fifo_status = 0, ++ .fifo_flush = 0, ++ ++}; ++ ++#endif /* _EN_ISOC_ */ ++/* Gadget Operations */ ++/** ++ * The following gadget operations will be implemented in the DWC_otg ++ * PCD. Functions in the API that are not described below are not ++ * implemented. ++ * ++ * The Gadget API provides wrapper functions for each of the function ++ * pointers defined in usb_gadget_ops. The Gadget Driver calls the ++ * wrapper function, which then calls the underlying PCD function. The ++ * following sections are named according to the wrapper functions ++ * (except for ioctl, which doesn't have a wrapper function). Within ++ * each section, the corresponding DWC_otg PCD function name is ++ * specified. ++ * ++ */ ++ ++/** ++ *Gets the USB Frame number of the last SOF. ++ */ ++static int get_frame_number(struct usb_gadget *gadget) ++{ ++ struct gadget_wrapper *d; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, gadget); ++ ++ if (gadget == 0) { ++ return -ENODEV; ++ } ++ ++ d = container_of(gadget, struct gadget_wrapper, gadget); ++ return dwc_otg_pcd_get_frame_number(d->pcd); ++} ++ ++#ifdef CONFIG_USB_DWC_OTG_LPM ++static int test_lpm_enabled(struct usb_gadget *gadget) ++{ ++ struct gadget_wrapper *d; ++ ++ d = container_of(gadget, struct gadget_wrapper, gadget); ++ ++ return dwc_otg_pcd_is_lpm_enabled(d->pcd); ++} ++#endif ++ ++/** ++ * Initiates Session Request Protocol (SRP) to wakeup the host if no ++ * session is in progress. If a session is already in progress, but ++ * the device is suspended, remote wakeup signaling is started. ++ * ++ */ ++static int wakeup(struct usb_gadget *gadget) ++{ ++ struct gadget_wrapper *d; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, gadget); ++ ++ if (gadget == 0) { ++ return -ENODEV; ++ } else { ++ d = container_of(gadget, struct gadget_wrapper, gadget); ++ } ++ dwc_otg_pcd_wakeup(d->pcd); ++ return 0; ++} ++ ++static const struct usb_gadget_ops dwc_otg_pcd_ops = { ++ .get_frame = get_frame_number, ++ .wakeup = wakeup, ++#ifdef CONFIG_USB_DWC_OTG_LPM ++ .lpm_support = test_lpm_enabled, ++#endif ++ // current versions must always be self-powered ++}; ++ ++static int _setup(dwc_otg_pcd_t * pcd, uint8_t * bytes) ++{ ++ int retval = -DWC_E_NOT_SUPPORTED; ++ if (gadget_wrapper->driver && gadget_wrapper->driver->setup) { ++ retval = gadget_wrapper->driver->setup(&gadget_wrapper->gadget, ++ (struct usb_ctrlrequest ++ *)bytes); ++ } ++ ++ if (retval == -ENOTSUPP) { ++ retval = -DWC_E_NOT_SUPPORTED; ++ } else if (retval < 0) { ++ retval = -DWC_E_INVALID; ++ } ++ ++ return retval; ++} ++ ++#ifdef DWC_EN_ISOC ++static int _isoc_complete(dwc_otg_pcd_t * pcd, void *ep_handle, ++ void *req_handle, int proc_buf_num) ++{ ++ int i, packet_count; ++ struct usb_gadget_iso_packet_descriptor *iso_packet = 0; ++ struct usb_iso_request *iso_req = req_handle; ++ ++ if (proc_buf_num) { ++ iso_packet = iso_req->iso_packet_desc1; ++ } else { ++ iso_packet = iso_req->iso_packet_desc0; ++ } ++ packet_count = ++ dwc_otg_pcd_get_iso_packet_count(pcd, ep_handle, req_handle); ++ for (i = 0; i < packet_count; ++i) { ++ int status; ++ int actual; ++ int offset; ++ dwc_otg_pcd_get_iso_packet_params(pcd, ep_handle, req_handle, ++ i, &status, &actual, &offset); ++ switch (status) { ++ case -DWC_E_NO_DATA: ++ status = -ENODATA; ++ break; ++ default: ++ if (status) { ++ DWC_PRINTF("unknown status in isoc packet\n"); ++ } ++ ++ } ++ iso_packet[i].status = status; ++ iso_packet[i].offset = offset; ++ iso_packet[i].actual_length = actual; ++ } ++ ++ iso_req->status = 0; ++ iso_req->process_buffer(ep_handle, iso_req); ++ ++ return 0; ++} ++#endif /* DWC_EN_ISOC */ ++ ++#ifdef DWC_UTE_PER_IO ++/** ++ * Copy the contents of the extended request to the Linux usb_request's ++ * extended part and call the gadget's completion. ++ * ++ * @param pcd Pointer to the pcd structure ++ * @param ep_handle Void pointer to the usb_ep structure ++ * @param req_handle Void pointer to the usb_request structure ++ * @param status Request status returned from the portable logic ++ * @param ereq_port Void pointer to the extended request structure ++ * created in the the portable part that contains the ++ * results of the processed iso packets. ++ */ ++static int _xisoc_complete(dwc_otg_pcd_t * pcd, void *ep_handle, ++ void *req_handle, int32_t status, void *ereq_port) ++{ ++ struct dwc_ute_iso_req_ext *ereqorg = NULL; ++ struct dwc_iso_xreq_port *ereqport = NULL; ++ struct dwc_ute_iso_packet_descriptor *desc_org = NULL; ++ int i; ++ struct usb_request *req; ++ //struct dwc_ute_iso_packet_descriptor * ++ //int status = 0; ++ ++ req = (struct usb_request *)req_handle; ++ ereqorg = &req->ext_req; ++ ereqport = (struct dwc_iso_xreq_port *)ereq_port; ++ desc_org = ereqorg->per_io_frame_descs; ++ ++ if (req && req->complete) { ++ /* Copy the request data from the portable logic to our request */ ++ for (i = 0; i < ereqport->pio_pkt_count; i++) { ++ desc_org[i].actual_length = ++ ereqport->per_io_frame_descs[i].actual_length; ++ desc_org[i].status = ++ ereqport->per_io_frame_descs[i].status; ++ } ++ ++ switch (status) { ++ case -DWC_E_SHUTDOWN: ++ req->status = -ESHUTDOWN; ++ break; ++ case -DWC_E_RESTART: ++ req->status = -ECONNRESET; ++ break; ++ case -DWC_E_INVALID: ++ req->status = -EINVAL; ++ break; ++ case -DWC_E_TIMEOUT: ++ req->status = -ETIMEDOUT; ++ break; ++ default: ++ req->status = status; ++ } ++ ++ /* And call the gadget's completion */ ++ req->complete(ep_handle, req); ++ } ++ ++ return 0; ++} ++#endif /* DWC_UTE_PER_IO */ ++ ++static int _complete(dwc_otg_pcd_t * pcd, void *ep_handle, ++ void *req_handle, int32_t status, uint32_t actual) ++{ ++ struct usb_request *req = (struct usb_request *)req_handle; ++#if LINUX_VERSION_CODE > KERNEL_VERSION(2,6,27) ++ struct dwc_otg_pcd_ep *ep = NULL; ++#endif ++ ++ if (req && req->complete) { ++ switch (status) { ++ case -DWC_E_SHUTDOWN: ++ req->status = -ESHUTDOWN; ++ break; ++ case -DWC_E_RESTART: ++ req->status = -ECONNRESET; ++ break; ++ case -DWC_E_INVALID: ++ req->status = -EINVAL; ++ break; ++ case -DWC_E_TIMEOUT: ++ req->status = -ETIMEDOUT; ++ break; ++ default: ++ req->status = status; ++ ++ } ++ ++ req->actual = actual; ++ DWC_SPINUNLOCK(pcd->lock); ++ req->complete(ep_handle, req); ++ DWC_SPINLOCK(pcd->lock); ++ } ++#if LINUX_VERSION_CODE > KERNEL_VERSION(2,6,27) ++ ep = ep_from_handle(pcd, ep_handle); ++ if (GET_CORE_IF(pcd)->dma_enable) { ++ if (req->length != 0) { ++ dwc_otg_device_t *otg_dev = gadget_wrapper->pcd->otg_dev; ++ struct device *dev = NULL; ++ ++ if (otg_dev != NULL) ++ dev = DWC_OTG_OS_GETDEV(otg_dev->os_dep); ++ ++ dma_unmap_single(dev, req->dma, req->length, ++ ep->dwc_ep.is_in ? ++ DMA_TO_DEVICE: DMA_FROM_DEVICE); ++ } ++ } ++#endif ++ ++ return 0; ++} ++ ++static int _connect(dwc_otg_pcd_t * pcd, int speed) ++{ ++ gadget_wrapper->gadget.speed = speed; ++ return 0; ++} ++ ++static int _disconnect(dwc_otg_pcd_t * pcd) ++{ ++ if (gadget_wrapper->driver && gadget_wrapper->driver->disconnect) { ++ gadget_wrapper->driver->disconnect(&gadget_wrapper->gadget); ++ } ++ return 0; ++} ++ ++static int _resume(dwc_otg_pcd_t * pcd) ++{ ++ if (gadget_wrapper->driver && gadget_wrapper->driver->resume) { ++ gadget_wrapper->driver->resume(&gadget_wrapper->gadget); ++ } ++ ++ return 0; ++} ++ ++static int _suspend(dwc_otg_pcd_t * pcd) ++{ ++ if (gadget_wrapper->driver && gadget_wrapper->driver->suspend) { ++ gadget_wrapper->driver->suspend(&gadget_wrapper->gadget); ++ } ++ return 0; ++} ++ ++/** ++ * This function updates the otg values in the gadget structure. ++ */ ++static int _hnp_changed(dwc_otg_pcd_t * pcd) ++{ ++ ++ if (!gadget_wrapper->gadget.is_otg) ++ return 0; ++ ++ gadget_wrapper->gadget.b_hnp_enable = get_b_hnp_enable(pcd); ++ gadget_wrapper->gadget.a_hnp_support = get_a_hnp_support(pcd); ++ gadget_wrapper->gadget.a_alt_hnp_support = get_a_alt_hnp_support(pcd); ++ return 0; ++} ++ ++static int _reset(dwc_otg_pcd_t * pcd) ++{ ++ return 0; ++} ++ ++#ifdef DWC_UTE_CFI ++static int _cfi_setup(dwc_otg_pcd_t * pcd, void *cfi_req) ++{ ++ int retval = -DWC_E_INVALID; ++ if (gadget_wrapper->driver->cfi_feature_setup) { ++ retval = ++ gadget_wrapper->driver-> ++ cfi_feature_setup(&gadget_wrapper->gadget, ++ (struct cfi_usb_ctrlrequest *)cfi_req); ++ } ++ ++ return retval; ++} ++#endif ++ ++static const struct dwc_otg_pcd_function_ops fops = { ++ .complete = _complete, ++#ifdef DWC_EN_ISOC ++ .isoc_complete = _isoc_complete, ++#endif ++ .setup = _setup, ++ .disconnect = _disconnect, ++ .connect = _connect, ++ .resume = _resume, ++ .suspend = _suspend, ++ .hnp_changed = _hnp_changed, ++ .reset = _reset, ++#ifdef DWC_UTE_CFI ++ .cfi_setup = _cfi_setup, ++#endif ++#ifdef DWC_UTE_PER_IO ++ .xisoc_complete = _xisoc_complete, ++#endif ++}; ++ ++/** ++ * This function is the top level PCD interrupt handler. ++ */ ++static irqreturn_t dwc_otg_pcd_irq(int irq, void *dev) ++{ ++ dwc_otg_pcd_t *pcd = dev; ++ int32_t retval = IRQ_NONE; ++ ++ retval = dwc_otg_pcd_handle_intr(pcd); ++ if (retval != 0) { ++ S3C2410X_CLEAR_EINTPEND(); ++ } ++ return IRQ_RETVAL(retval); ++} ++ ++/** ++ * This function initialized the usb_ep structures to there default ++ * state. ++ * ++ * @param d Pointer on gadget_wrapper. ++ */ ++void gadget_add_eps(struct gadget_wrapper *d) ++{ ++ static const char *names[] = { ++ ++ "ep0", ++ "ep1in", ++ "ep2in", ++ "ep3in", ++ "ep4in", ++ "ep5in", ++ "ep6in", ++ "ep7in", ++ "ep8in", ++ "ep9in", ++ "ep10in", ++ "ep11in", ++ "ep12in", ++ "ep13in", ++ "ep14in", ++ "ep15in", ++ "ep1out", ++ "ep2out", ++ "ep3out", ++ "ep4out", ++ "ep5out", ++ "ep6out", ++ "ep7out", ++ "ep8out", ++ "ep9out", ++ "ep10out", ++ "ep11out", ++ "ep12out", ++ "ep13out", ++ "ep14out", ++ "ep15out" ++ }; ++ ++ int i; ++ struct usb_ep *ep; ++ int8_t dev_endpoints; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s\n", __func__); ++ ++ INIT_LIST_HEAD(&d->gadget.ep_list); ++ d->gadget.ep0 = &d->ep0; ++ d->gadget.speed = USB_SPEED_UNKNOWN; ++ ++ INIT_LIST_HEAD(&d->gadget.ep0->ep_list); ++ ++ /** ++ * Initialize the EP0 structure. ++ */ ++ ep = &d->ep0; ++ ++ /* Init the usb_ep structure. */ ++ ep->name = names[0]; ++ ep->ops = (struct usb_ep_ops *)&dwc_otg_pcd_ep_ops; ++ ++ /** ++ * @todo NGS: What should the max packet size be set to ++ * here? Before EP type is set? ++ */ ++ ep->maxpacket = MAX_PACKET_SIZE; ++ dwc_otg_pcd_ep_enable(d->pcd, NULL, ep); ++ ++ list_add_tail(&ep->ep_list, &d->gadget.ep_list); ++ ++ /** ++ * Initialize the EP structures. ++ */ ++ dev_endpoints = d->pcd->core_if->dev_if->num_in_eps; ++ ++ for (i = 0; i < dev_endpoints; i++) { ++ ep = &d->in_ep[i]; ++ ++ /* Init the usb_ep structure. */ ++ ep->name = names[d->pcd->in_ep[i].dwc_ep.num]; ++ ep->ops = (struct usb_ep_ops *)&dwc_otg_pcd_ep_ops; ++ ++ /** ++ * @todo NGS: What should the max packet size be set to ++ * here? Before EP type is set? ++ */ ++ ep->maxpacket = MAX_PACKET_SIZE; ++ list_add_tail(&ep->ep_list, &d->gadget.ep_list); ++ } ++ ++ dev_endpoints = d->pcd->core_if->dev_if->num_out_eps; ++ ++ for (i = 0; i < dev_endpoints; i++) { ++ ep = &d->out_ep[i]; ++ ++ /* Init the usb_ep structure. */ ++ ep->name = names[15 + d->pcd->out_ep[i].dwc_ep.num]; ++ ep->ops = (struct usb_ep_ops *)&dwc_otg_pcd_ep_ops; ++ ++ /** ++ * @todo NGS: What should the max packet size be set to ++ * here? Before EP type is set? ++ */ ++ ep->maxpacket = MAX_PACKET_SIZE; ++ ++ list_add_tail(&ep->ep_list, &d->gadget.ep_list); ++ } ++ ++ /* remove ep0 from the list. There is a ep0 pointer. */ ++ list_del_init(&d->ep0.ep_list); ++ ++ d->ep0.maxpacket = MAX_EP0_SIZE; ++} ++ ++/** ++ * This function releases the Gadget device. ++ * required by device_unregister(). ++ * ++ * @todo Should this do something? Should it free the PCD? ++ */ ++static void dwc_otg_pcd_gadget_release(struct device *dev) ++{ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p)\n", __func__, dev); ++} ++ ++static struct gadget_wrapper *alloc_wrapper(dwc_bus_dev_t *_dev) ++{ ++ static char pcd_name[] = "dwc_otg_pcd"; ++ dwc_otg_device_t *otg_dev = DWC_OTG_BUSDRVDATA(_dev); ++ struct gadget_wrapper *d; ++ int retval; ++ ++ d = DWC_ALLOC(sizeof(*d)); ++ if (d == NULL) { ++ return NULL; ++ } ++ ++ memset(d, 0, sizeof(*d)); ++ ++ d->gadget.name = pcd_name; ++ d->pcd = otg_dev->pcd; ++ ++#if LINUX_VERSION_CODE < KERNEL_VERSION(2,6,30) ++ strcpy(d->gadget.dev.bus_id, "gadget"); ++#else ++ dev_set_name(&d->gadget.dev, "%s", "gadget"); ++#endif ++ ++ d->gadget.dev.parent = &_dev->dev; ++ d->gadget.dev.release = dwc_otg_pcd_gadget_release; ++ d->gadget.ops = &dwc_otg_pcd_ops; ++ d->gadget.max_speed = dwc_otg_pcd_is_dualspeed(otg_dev->pcd) ? USB_SPEED_HIGH:USB_SPEED_FULL; ++ d->gadget.is_otg = dwc_otg_pcd_is_otg(otg_dev->pcd); ++ ++ d->driver = 0; ++ /* Register the gadget device */ ++ retval = device_register(&d->gadget.dev); ++ if (retval != 0) { ++ DWC_ERROR("device_register failed\n"); ++ DWC_FREE(d); ++ return NULL; ++ } ++ ++ return d; ++} ++ ++static void free_wrapper(struct gadget_wrapper *d) ++{ ++ if (d->driver) { ++ /* should have been done already by driver model core */ ++ DWC_WARN("driver '%s' is still registered\n", ++ d->driver->driver.name); ++#ifdef CONFIG_USB_GADGET ++ usb_gadget_unregister_driver(d->driver); ++#endif ++ } ++ ++ device_unregister(&d->gadget.dev); ++ DWC_FREE(d); ++} ++ ++/** ++ * This function initialized the PCD portion of the driver. ++ * ++ */ ++int pcd_init(dwc_bus_dev_t *_dev) ++{ ++ dwc_otg_device_t *otg_dev = DWC_OTG_BUSDRVDATA(_dev); ++ int retval = 0; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p) otg_dev=%p\n", __func__, _dev, otg_dev); ++ ++ otg_dev->pcd = dwc_otg_pcd_init(otg_dev); ++ ++ if (!otg_dev->pcd) { ++ DWC_ERROR("dwc_otg_pcd_init failed\n"); ++ return -ENOMEM; ++ } ++ ++ otg_dev->pcd->otg_dev = otg_dev; ++ gadget_wrapper = alloc_wrapper(_dev); ++ ++ /* ++ * Initialize EP structures ++ */ ++ gadget_add_eps(gadget_wrapper); ++ /* ++ * Setup interupt handler ++ */ ++ DWC_DEBUGPL(DBG_ANY, "registering handler for irq%d\n", ++ otg_dev->os_dep.irq_num); ++ retval = request_irq(otg_dev->os_dep.irq_num, dwc_otg_pcd_irq, ++ IRQF_SHARED, gadget_wrapper->gadget.name, ++ otg_dev->pcd); ++ if (retval != 0) { ++ DWC_ERROR("request of irq%d failed\n", otg_dev->os_dep.irq_num); ++ free_wrapper(gadget_wrapper); ++ return -EBUSY; ++ } ++ ++ dwc_otg_pcd_start(gadget_wrapper->pcd, &fops); ++ ++ return retval; ++} ++ ++/** ++ * Cleanup the PCD. ++ */ ++void pcd_remove(dwc_bus_dev_t *_dev) ++{ ++ dwc_otg_device_t *otg_dev = DWC_OTG_BUSDRVDATA(_dev); ++ dwc_otg_pcd_t *pcd = otg_dev->pcd; ++ ++ DWC_DEBUGPL(DBG_PCDV, "%s(%p) otg_dev %p\n", __func__, _dev, otg_dev); ++ ++ /* ++ * Free the IRQ ++ */ ++ free_irq(otg_dev->os_dep.irq_num, pcd); ++ dwc_otg_pcd_remove(otg_dev->pcd); ++ free_wrapper(gadget_wrapper); ++ otg_dev->pcd = 0; ++} ++ ++#endif /* DWC_HOST_ONLY */ +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/dwc_otg_regs.h +@@ -0,0 +1,2550 @@ ++/* ========================================================================== ++ * $File: //dwh/usb_iip/dev/software/otg/linux/drivers/dwc_otg_regs.h $ ++ * $Revision: #98 $ ++ * $Date: 2012/08/10 $ ++ * $Change: 2047372 $ ++ * ++ * Synopsys HS OTG Linux Software Driver and documentation (hereinafter, ++ * "Software") is an Unsupported proprietary work of Synopsys, Inc. unless ++ * otherwise expressly agreed to in writing between Synopsys and you. ++ * ++ * The Software IS NOT an item of Licensed Software or Licensed Product under ++ * any End User Software License Agreement or Agreement for Licensed Product ++ * with Synopsys or any supplement thereto. You are permitted to use and ++ * redistribute this Software in source and binary forms, with or without ++ * modification, provided that redistributions of source code must retain this ++ * notice. You may not view, use, disclose, copy or distribute this file or ++ * any information contained herein except pursuant to this license grant from ++ * Synopsys. If you do not agree with this notice, including the disclaimer ++ * below, then you are not authorized to use the Software. ++ * ++ * THIS SOFTWARE IS BEING DISTRIBUTED BY SYNOPSYS SOLELY ON AN "AS IS" BASIS ++ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE ++ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ++ * ARE HEREBY DISCLAIMED. IN NO EVENT SHALL SYNOPSYS BE LIABLE FOR ANY DIRECT, ++ * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR ++ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER ++ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT ++ * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY ++ * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH ++ * DAMAGE. ++ * ========================================================================== */ ++ ++#ifndef __DWC_OTG_REGS_H__ ++#define __DWC_OTG_REGS_H__ ++ ++#include "dwc_otg_core_if.h" ++ ++/** ++ * @file ++ * ++ * This file contains the data structures for accessing the DWC_otg core registers. ++ * ++ * The application interfaces with the HS OTG core by reading from and ++ * writing to the Control and Status Register (CSR) space through the ++ * AHB Slave interface. These registers are 32 bits wide, and the ++ * addresses are 32-bit-block aligned. ++ * CSRs are classified as follows: ++ * - Core Global Registers ++ * - Device Mode Registers ++ * - Device Global Registers ++ * - Device Endpoint Specific Registers ++ * - Host Mode Registers ++ * - Host Global Registers ++ * - Host Port CSRs ++ * - Host Channel Specific Registers ++ * ++ * Only the Core Global registers can be accessed in both Device and ++ * Host modes. When the HS OTG core is operating in one mode, either ++ * Device or Host, the application must not access registers from the ++ * other mode. When the core switches from one mode to another, the ++ * registers in the new mode of operation must be reprogrammed as they ++ * would be after a power-on reset. ++ */ ++ ++/****************************************************************************/ ++/** DWC_otg Core registers . ++ * The dwc_otg_core_global_regs structure defines the size ++ * and relative field offsets for the Core Global registers. ++ */ ++typedef struct dwc_otg_core_global_regs { ++ /** OTG Control and Status Register. Offset: 000h */ ++ volatile uint32_t gotgctl; ++ /** OTG Interrupt Register. Offset: 004h */ ++ volatile uint32_t gotgint; ++ /**Core AHB Configuration Register. Offset: 008h */ ++ volatile uint32_t gahbcfg; ++ ++#define DWC_GLBINTRMASK 0x0001 ++#define DWC_DMAENABLE 0x0020 ++#define DWC_NPTXEMPTYLVL_EMPTY 0x0080 ++#define DWC_NPTXEMPTYLVL_HALFEMPTY 0x0000 ++#define DWC_PTXEMPTYLVL_EMPTY 0x0100 ++#define DWC_PTXEMPTYLVL_HALFEMPTY 0x0000 ++ ++ /**Core USB Configuration Register. Offset: 00Ch */ ++ volatile uint32_t gusbcfg; ++ /**Core Reset Register. Offset: 010h */ ++ volatile uint32_t grstctl; ++ /**Core Interrupt Register. Offset: 014h */ ++ volatile uint32_t gintsts; ++ /**Core Interrupt Mask Register. Offset: 018h */ ++ volatile uint32_t gintmsk; ++ /**Receive Status Queue Read Register (Read Only). Offset: 01Ch */ ++ volatile uint32_t grxstsr; ++ /**Receive Status Queue Read & POP Register (Read Only). Offset: 020h*/ ++ volatile uint32_t grxstsp; ++ /**Receive FIFO Size Register. Offset: 024h */ ++ volatile uint32_t grxfsiz; ++ /**Non Periodic Transmit FIFO Size Register. Offset: 028h */ ++ volatile uint32_t gnptxfsiz; ++ /**Non Periodic Transmit FIFO/Queue Status Register (Read ++ * Only). Offset: 02Ch */ ++ volatile uint32_t gnptxsts; ++ /**I2C Access Register. Offset: 030h */ ++ volatile uint32_t gi2cctl; ++ /**PHY Vendor Control Register. Offset: 034h */ ++ volatile uint32_t gpvndctl; ++ /**General Purpose Input/Output Register. Offset: 038h */ ++ volatile uint32_t ggpio; ++ /**User ID Register. Offset: 03Ch */ ++ volatile uint32_t guid; ++ /**Synopsys ID Register (Read Only). Offset: 040h */ ++ volatile uint32_t gsnpsid; ++ /**User HW Config1 Register (Read Only). Offset: 044h */ ++ volatile uint32_t ghwcfg1; ++ /**User HW Config2 Register (Read Only). Offset: 048h */ ++ volatile uint32_t ghwcfg2; ++#define DWC_SLAVE_ONLY_ARCH 0 ++#define DWC_EXT_DMA_ARCH 1 ++#define DWC_INT_DMA_ARCH 2 ++ ++#define DWC_MODE_HNP_SRP_CAPABLE 0 ++#define DWC_MODE_SRP_ONLY_CAPABLE 1 ++#define DWC_MODE_NO_HNP_SRP_CAPABLE 2 ++#define DWC_MODE_SRP_CAPABLE_DEVICE 3 ++#define DWC_MODE_NO_SRP_CAPABLE_DEVICE 4 ++#define DWC_MODE_SRP_CAPABLE_HOST 5 ++#define DWC_MODE_NO_SRP_CAPABLE_HOST 6 ++ ++ /**User HW Config3 Register (Read Only). Offset: 04Ch */ ++ volatile uint32_t ghwcfg3; ++ /**User HW Config4 Register (Read Only). Offset: 050h*/ ++ volatile uint32_t ghwcfg4; ++ /** Core LPM Configuration register Offset: 054h*/ ++ volatile uint32_t glpmcfg; ++ /** Global PowerDn Register Offset: 058h */ ++ volatile uint32_t gpwrdn; ++ /** Global DFIFO SW Config Register Offset: 05Ch */ ++ volatile uint32_t gdfifocfg; ++ /** ADP Control Register Offset: 060h */ ++ volatile uint32_t adpctl; ++ /** Reserved Offset: 064h-0FFh */ ++ volatile uint32_t reserved39[39]; ++ /** Host Periodic Transmit FIFO Size Register. Offset: 100h */ ++ volatile uint32_t hptxfsiz; ++ /** Device Periodic Transmit FIFO#n Register if dedicated fifos are disabled, ++ otherwise Device Transmit FIFO#n Register. ++ * Offset: 104h + (FIFO_Number-1)*04h, 1 <= FIFO Number <= 15 (1<=n<=15). */ ++ volatile uint32_t dtxfsiz[15]; ++} dwc_otg_core_global_regs_t; ++ ++/** ++ * This union represents the bit fields of the Core OTG Control ++ * and Status Register (GOTGCTL). Set the bits using the bit ++ * fields then write the d32 value to the register. ++ */ ++typedef union gotgctl_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned sesreqscs:1; ++ unsigned sesreq:1; ++ unsigned vbvalidoven:1; ++ unsigned vbvalidovval:1; ++ unsigned avalidoven:1; ++ unsigned avalidovval:1; ++ unsigned bvalidoven:1; ++ unsigned bvalidovval:1; ++ unsigned hstnegscs:1; ++ unsigned hnpreq:1; ++ unsigned hstsethnpen:1; ++ unsigned devhnpen:1; ++ unsigned reserved12_15:4; ++ unsigned conidsts:1; ++ unsigned dbnctime:1; ++ unsigned asesvld:1; ++ unsigned bsesvld:1; ++ unsigned otgver:1; ++ unsigned reserved1:1; ++ unsigned multvalidbc:5; ++ unsigned chirpen:1; ++ unsigned reserved28_31:4; ++ } b; ++} gotgctl_data_t; ++ ++/** ++ * This union represents the bit fields of the Core OTG Interrupt Register ++ * (GOTGINT). Set/clear the bits using the bit fields then write the d32 ++ * value to the register. ++ */ ++typedef union gotgint_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** Current Mode */ ++ unsigned reserved0_1:2; ++ ++ /** Session End Detected */ ++ unsigned sesenddet:1; ++ ++ unsigned reserved3_7:5; ++ ++ /** Session Request Success Status Change */ ++ unsigned sesreqsucstschng:1; ++ /** Host Negotiation Success Status Change */ ++ unsigned hstnegsucstschng:1; ++ ++ unsigned reserved10_16:7; ++ ++ /** Host Negotiation Detected */ ++ unsigned hstnegdet:1; ++ /** A-Device Timeout Change */ ++ unsigned adevtoutchng:1; ++ /** Debounce Done */ ++ unsigned debdone:1; ++ /** Multi-Valued input changed */ ++ unsigned mvic:1; ++ ++ unsigned reserved31_21:11; ++ ++ } b; ++} gotgint_data_t; ++ ++/** ++ * This union represents the bit fields of the Core AHB Configuration ++ * Register (GAHBCFG). Set/clear the bits using the bit fields then ++ * write the d32 value to the register. ++ */ ++typedef union gahbcfg_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned glblintrmsk:1; ++#define DWC_GAHBCFG_GLBINT_ENABLE 1 ++ ++ unsigned hburstlen:4; ++#define DWC_GAHBCFG_INT_DMA_BURST_SINGLE 0 ++#define DWC_GAHBCFG_INT_DMA_BURST_INCR 1 ++#define DWC_GAHBCFG_INT_DMA_BURST_INCR4 3 ++#define DWC_GAHBCFG_INT_DMA_BURST_INCR8 5 ++#define DWC_GAHBCFG_INT_DMA_BURST_INCR16 7 ++ ++ unsigned dmaenable:1; ++#define DWC_GAHBCFG_DMAENABLE 1 ++ unsigned reserved:1; ++ unsigned nptxfemplvl_txfemplvl:1; ++ unsigned ptxfemplvl:1; ++#define DWC_GAHBCFG_TXFEMPTYLVL_EMPTY 1 ++#define DWC_GAHBCFG_TXFEMPTYLVL_HALFEMPTY 0 ++ unsigned reserved9_20:12; ++ unsigned remmemsupp:1; ++ unsigned notialldmawrit:1; ++ unsigned ahbsingle:1; ++ unsigned reserved24_31:8; ++ } b; ++} gahbcfg_data_t; ++ ++/** ++ * This union represents the bit fields of the Core USB Configuration ++ * Register (GUSBCFG). Set the bits using the bit fields then write ++ * the d32 value to the register. ++ */ ++typedef union gusbcfg_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned toutcal:3; ++ unsigned phyif:1; ++ unsigned ulpi_utmi_sel:1; ++ unsigned fsintf:1; ++ unsigned physel:1; ++ unsigned ddrsel:1; ++ unsigned srpcap:1; ++ unsigned hnpcap:1; ++ unsigned usbtrdtim:4; ++ unsigned reserved1:1; ++ unsigned phylpwrclksel:1; ++ unsigned otgutmifssel:1; ++ unsigned ulpi_fsls:1; ++ unsigned ulpi_auto_res:1; ++ unsigned ulpi_clk_sus_m:1; ++ unsigned ulpi_ext_vbus_drv:1; ++ unsigned ulpi_int_vbus_indicator:1; ++ unsigned term_sel_dl_pulse:1; ++ unsigned indicator_complement:1; ++ unsigned indicator_pass_through:1; ++ unsigned ulpi_int_prot_dis:1; ++ unsigned ic_usb_cap:1; ++ unsigned ic_traffic_pull_remove:1; ++ unsigned tx_end_delay:1; ++ unsigned force_host_mode:1; ++ unsigned force_dev_mode:1; ++ unsigned reserved31:1; ++ } b; ++} gusbcfg_data_t; ++ ++/** ++ * This union represents the bit fields of the Core Reset Register ++ * (GRSTCTL). Set/clear the bits using the bit fields then write the ++ * d32 value to the register. ++ */ ++typedef union grstctl_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** Core Soft Reset (CSftRst) (Device and Host) ++ * ++ * The application can flush the control logic in the ++ * entire core using this bit. This bit resets the ++ * pipelines in the AHB Clock domain as well as the ++ * PHY Clock domain. ++ * ++ * The state machines are reset to an IDLE state, the ++ * control bits in the CSRs are cleared, all the ++ * transmit FIFOs and the receive FIFO are flushed. ++ * ++ * The status mask bits that control the generation of ++ * the interrupt, are cleared, to clear the ++ * interrupt. The interrupt status bits are not ++ * cleared, so the application can get the status of ++ * any events that occurred in the core after it has ++ * set this bit. ++ * ++ * Any transactions on the AHB are terminated as soon ++ * as possible following the protocol. Any ++ * transactions on the USB are terminated immediately. ++ * ++ * The configuration settings in the CSRs are ++ * unchanged, so the software doesn't have to ++ * reprogram these registers (Device ++ * Configuration/Host Configuration/Core System ++ * Configuration/Core PHY Configuration). ++ * ++ * The application can write to this bit, any time it ++ * wants to reset the core. This is a self clearing ++ * bit and the core clears this bit after all the ++ * necessary logic is reset in the core, which may ++ * take several clocks, depending on the current state ++ * of the core. ++ */ ++ unsigned csftrst:1; ++ /** Hclk Soft Reset ++ * ++ * The application uses this bit to reset the control logic in ++ * the AHB clock domain. Only AHB clock domain pipelines are ++ * reset. ++ */ ++ unsigned hsftrst:1; ++ /** Host Frame Counter Reset (Host Only)
++ * ++ * The application can reset the (micro)frame number ++ * counter inside the core, using this bit. When the ++ * (micro)frame counter is reset, the subsequent SOF ++ * sent out by the core, will have a (micro)frame ++ * number of 0. ++ */ ++ unsigned hstfrm:1; ++ /** In Token Sequence Learning Queue Flush ++ * (INTknQFlsh) (Device Only) ++ */ ++ unsigned intknqflsh:1; ++ /** RxFIFO Flush (RxFFlsh) (Device and Host) ++ * ++ * The application can flush the entire Receive FIFO ++ * using this bit. The application must first ++ * ensure that the core is not in the middle of a ++ * transaction. The application should write into ++ * this bit, only after making sure that neither the ++ * DMA engine is reading from the RxFIFO nor the MAC ++ * is writing the data in to the FIFO. The ++ * application should wait until the bit is cleared ++ * before performing any other operations. This bit ++ * will takes 8 clocks (slowest of PHY or AHB clock) ++ * to clear. ++ */ ++ unsigned rxfflsh:1; ++ /** TxFIFO Flush (TxFFlsh) (Device and Host). ++ * ++ * This bit is used to selectively flush a single or ++ * all transmit FIFOs. The application must first ++ * ensure that the core is not in the middle of a ++ * transaction. The application should write into ++ * this bit, only after making sure that neither the ++ * DMA engine is writing into the TxFIFO nor the MAC ++ * is reading the data out of the FIFO. The ++ * application should wait until the core clears this ++ * bit, before performing any operations. This bit ++ * will takes 8 clocks (slowest of PHY or AHB clock) ++ * to clear. ++ */ ++ unsigned txfflsh:1; ++ ++ /** TxFIFO Number (TxFNum) (Device and Host). ++ * ++ * This is the FIFO number which needs to be flushed, ++ * using the TxFIFO Flush bit. This field should not ++ * be changed until the TxFIFO Flush bit is cleared by ++ * the core. ++ * - 0x0 : Non Periodic TxFIFO Flush ++ * - 0x1 : Periodic TxFIFO #1 Flush in device mode ++ * or Periodic TxFIFO in host mode ++ * - 0x2 : Periodic TxFIFO #2 Flush in device mode. ++ * - ... ++ * - 0xF : Periodic TxFIFO #15 Flush in device mode ++ * - 0x10: Flush all the Transmit NonPeriodic and ++ * Transmit Periodic FIFOs in the core ++ */ ++ unsigned txfnum:5; ++ /** Reserved */ ++ unsigned reserved11_29:19; ++ /** DMA Request Signal. Indicated DMA request is in ++ * probress. Used for debug purpose. */ ++ unsigned dmareq:1; ++ /** AHB Master Idle. Indicates the AHB Master State ++ * Machine is in IDLE condition. */ ++ unsigned ahbidle:1; ++ } b; ++} grstctl_t; ++ ++/** ++ * This union represents the bit fields of the Core Interrupt Mask ++ * Register (GINTMSK). Set/clear the bits using the bit fields then ++ * write the d32 value to the register. ++ */ ++typedef union gintmsk_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned reserved0:1; ++ unsigned modemismatch:1; ++ unsigned otgintr:1; ++ unsigned sofintr:1; ++ unsigned rxstsqlvl:1; ++ unsigned nptxfempty:1; ++ unsigned ginnakeff:1; ++ unsigned goutnakeff:1; ++ unsigned ulpickint:1; ++ unsigned i2cintr:1; ++ unsigned erlysuspend:1; ++ unsigned usbsuspend:1; ++ unsigned usbreset:1; ++ unsigned enumdone:1; ++ unsigned isooutdrop:1; ++ unsigned eopframe:1; ++ unsigned restoredone:1; ++ unsigned epmismatch:1; ++ unsigned inepintr:1; ++ unsigned outepintr:1; ++ unsigned incomplisoin:1; ++ unsigned incomplisoout:1; ++ unsigned fetsusp:1; ++ unsigned resetdet:1; ++ unsigned portintr:1; ++ unsigned hcintr:1; ++ unsigned ptxfempty:1; ++ unsigned lpmtranrcvd:1; ++ unsigned conidstschng:1; ++ unsigned disconnect:1; ++ unsigned sessreqintr:1; ++ unsigned wkupintr:1; ++ } b; ++} gintmsk_data_t; ++/** ++ * This union represents the bit fields of the Core Interrupt Register ++ * (GINTSTS). Set/clear the bits using the bit fields then write the ++ * d32 value to the register. ++ */ ++typedef union gintsts_data { ++ /** raw register data */ ++ uint32_t d32; ++#define DWC_SOF_INTR_MASK 0x0008 ++ /** register bits */ ++ struct { ++#define DWC_HOST_MODE 1 ++ unsigned curmode:1; ++ unsigned modemismatch:1; ++ unsigned otgintr:1; ++ unsigned sofintr:1; ++ unsigned rxstsqlvl:1; ++ unsigned nptxfempty:1; ++ unsigned ginnakeff:1; ++ unsigned goutnakeff:1; ++ unsigned ulpickint:1; ++ unsigned i2cintr:1; ++ unsigned erlysuspend:1; ++ unsigned usbsuspend:1; ++ unsigned usbreset:1; ++ unsigned enumdone:1; ++ unsigned isooutdrop:1; ++ unsigned eopframe:1; ++ unsigned restoredone:1; ++ unsigned epmismatch:1; ++ unsigned inepint:1; ++ unsigned outepintr:1; ++ unsigned incomplisoin:1; ++ unsigned incomplisoout:1; ++ unsigned fetsusp:1; ++ unsigned resetdet:1; ++ unsigned portintr:1; ++ unsigned hcintr:1; ++ unsigned ptxfempty:1; ++ unsigned lpmtranrcvd:1; ++ unsigned conidstschng:1; ++ unsigned disconnect:1; ++ unsigned sessreqintr:1; ++ unsigned wkupintr:1; ++ } b; ++} gintsts_data_t; ++ ++/** ++ * This union represents the bit fields in the Device Receive Status Read and ++ * Pop Registers (GRXSTSR, GRXSTSP) Read the register into the d32 ++ * element then read out the bits using the bit elements. ++ */ ++typedef union device_grxsts_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned epnum:4; ++ unsigned bcnt:11; ++ unsigned dpid:2; ++ ++#define DWC_STS_DATA_UPDT 0x2 // OUT Data Packet ++#define DWC_STS_XFER_COMP 0x3 // OUT Data Transfer Complete ++ ++#define DWC_DSTS_GOUT_NAK 0x1 // Global OUT NAK ++#define DWC_DSTS_SETUP_COMP 0x4 // Setup Phase Complete ++#define DWC_DSTS_SETUP_UPDT 0x6 // SETUP Packet ++ unsigned pktsts:4; ++ unsigned fn:4; ++ unsigned reserved25_31:7; ++ } b; ++} device_grxsts_data_t; ++ ++/** ++ * This union represents the bit fields in the Host Receive Status Read and ++ * Pop Registers (GRXSTSR, GRXSTSP) Read the register into the d32 ++ * element then read out the bits using the bit elements. ++ */ ++typedef union host_grxsts_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned chnum:4; ++ unsigned bcnt:11; ++ unsigned dpid:2; ++ ++ unsigned pktsts:4; ++#define DWC_GRXSTS_PKTSTS_IN 0x2 ++#define DWC_GRXSTS_PKTSTS_IN_XFER_COMP 0x3 ++#define DWC_GRXSTS_PKTSTS_DATA_TOGGLE_ERR 0x5 ++#define DWC_GRXSTS_PKTSTS_CH_HALTED 0x7 ++ ++ unsigned reserved21_31:11; ++ } b; ++} host_grxsts_data_t; ++ ++/** ++ * This union represents the bit fields in the FIFO Size Registers (HPTXFSIZ, ++ * GNPTXFSIZ, DPTXFSIZn, DIEPTXFn). Read the register into the d32 element ++ * then read out the bits using the bit elements. ++ */ ++typedef union fifosize_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned startaddr:16; ++ unsigned depth:16; ++ } b; ++} fifosize_data_t; ++ ++/** ++ * This union represents the bit fields in the Non-Periodic Transmit ++ * FIFO/Queue Status Register (GNPTXSTS). Read the register into the ++ * d32 element then read out the bits using the bit ++ * elements. ++ */ ++typedef union gnptxsts_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned nptxfspcavail:16; ++ unsigned nptxqspcavail:8; ++ /** Top of the Non-Periodic Transmit Request Queue ++ * - bit 24 - Terminate (Last entry for the selected ++ * channel/EP) ++ * - bits 26:25 - Token Type ++ * - 2'b00 - IN/OUT ++ * - 2'b01 - Zero Length OUT ++ * - 2'b10 - PING/Complete Split ++ * - 2'b11 - Channel Halt ++ * - bits 30:27 - Channel/EP Number ++ */ ++ unsigned nptxqtop_terminate:1; ++ unsigned nptxqtop_token:2; ++ unsigned nptxqtop_chnep:4; ++ unsigned reserved:1; ++ } b; ++} gnptxsts_data_t; ++ ++/** ++ * This union represents the bit fields in the Transmit ++ * FIFO Status Register (DTXFSTS). Read the register into the ++ * d32 element then read out the bits using the bit ++ * elements. ++ */ ++typedef union dtxfsts_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned txfspcavail:16; ++ unsigned reserved:16; ++ } b; ++} dtxfsts_data_t; ++ ++/** ++ * This union represents the bit fields in the I2C Control Register ++ * (I2CCTL). Read the register into the d32 element then read out the ++ * bits using the bit elements. ++ */ ++typedef union gi2cctl_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned rwdata:8; ++ unsigned regaddr:8; ++ unsigned addr:7; ++ unsigned i2cen:1; ++ unsigned ack:1; ++ unsigned i2csuspctl:1; ++ unsigned i2cdevaddr:2; ++ unsigned i2cdatse0:1; ++ unsigned reserved:1; ++ unsigned rw:1; ++ unsigned bsydne:1; ++ } b; ++} gi2cctl_data_t; ++ ++/** ++ * This union represents the bit fields in the PHY Vendor Control Register ++ * (GPVNDCTL). Read the register into the d32 element then read out the ++ * bits using the bit elements. ++ */ ++typedef union gpvndctl_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned regdata:8; ++ unsigned vctrl:8; ++ unsigned regaddr16_21:6; ++ unsigned regwr:1; ++ unsigned reserved23_24:2; ++ unsigned newregreq:1; ++ unsigned vstsbsy:1; ++ unsigned vstsdone:1; ++ unsigned reserved28_30:3; ++ unsigned disulpidrvr:1; ++ } b; ++} gpvndctl_data_t; ++ ++/** ++ * This union represents the bit fields in the General Purpose ++ * Input/Output Register (GGPIO). ++ * Read the register into the d32 element then read out the ++ * bits using the bit elements. ++ */ ++typedef union ggpio_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned gpi:16; ++ unsigned gpo:16; ++ } b; ++} ggpio_data_t; ++ ++/** ++ * This union represents the bit fields in the User ID Register ++ * (GUID). Read the register into the d32 element then read out the ++ * bits using the bit elements. ++ */ ++typedef union guid_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned rwdata:32; ++ } b; ++} guid_data_t; ++ ++/** ++ * This union represents the bit fields in the Synopsys ID Register ++ * (GSNPSID). Read the register into the d32 element then read out the ++ * bits using the bit elements. ++ */ ++typedef union gsnpsid_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned rwdata:32; ++ } b; ++} gsnpsid_data_t; ++ ++/** ++ * This union represents the bit fields in the User HW Config1 ++ * Register. Read the register into the d32 element then read ++ * out the bits using the bit elements. ++ */ ++typedef union hwcfg1_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned ep_dir0:2; ++ unsigned ep_dir1:2; ++ unsigned ep_dir2:2; ++ unsigned ep_dir3:2; ++ unsigned ep_dir4:2; ++ unsigned ep_dir5:2; ++ unsigned ep_dir6:2; ++ unsigned ep_dir7:2; ++ unsigned ep_dir8:2; ++ unsigned ep_dir9:2; ++ unsigned ep_dir10:2; ++ unsigned ep_dir11:2; ++ unsigned ep_dir12:2; ++ unsigned ep_dir13:2; ++ unsigned ep_dir14:2; ++ unsigned ep_dir15:2; ++ } b; ++} hwcfg1_data_t; ++ ++/** ++ * This union represents the bit fields in the User HW Config2 ++ * Register. Read the register into the d32 element then read ++ * out the bits using the bit elements. ++ */ ++typedef union hwcfg2_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /* GHWCFG2 */ ++ unsigned op_mode:3; ++#define DWC_HWCFG2_OP_MODE_HNP_SRP_CAPABLE_OTG 0 ++#define DWC_HWCFG2_OP_MODE_SRP_ONLY_CAPABLE_OTG 1 ++#define DWC_HWCFG2_OP_MODE_NO_HNP_SRP_CAPABLE_OTG 2 ++#define DWC_HWCFG2_OP_MODE_SRP_CAPABLE_DEVICE 3 ++#define DWC_HWCFG2_OP_MODE_NO_SRP_CAPABLE_DEVICE 4 ++#define DWC_HWCFG2_OP_MODE_SRP_CAPABLE_HOST 5 ++#define DWC_HWCFG2_OP_MODE_NO_SRP_CAPABLE_HOST 6 ++ ++ unsigned architecture:2; ++ unsigned point2point:1; ++ unsigned hs_phy_type:2; ++#define DWC_HWCFG2_HS_PHY_TYPE_NOT_SUPPORTED 0 ++#define DWC_HWCFG2_HS_PHY_TYPE_UTMI 1 ++#define DWC_HWCFG2_HS_PHY_TYPE_ULPI 2 ++#define DWC_HWCFG2_HS_PHY_TYPE_UTMI_ULPI 3 ++ ++ unsigned fs_phy_type:2; ++ unsigned num_dev_ep:4; ++ unsigned num_host_chan:4; ++ unsigned perio_ep_supported:1; ++ unsigned dynamic_fifo:1; ++ unsigned multi_proc_int:1; ++ unsigned reserved21:1; ++ unsigned nonperio_tx_q_depth:2; ++ unsigned host_perio_tx_q_depth:2; ++ unsigned dev_token_q_depth:5; ++ unsigned otg_enable_ic_usb:1; ++ } b; ++} hwcfg2_data_t; ++ ++/** ++ * This union represents the bit fields in the User HW Config3 ++ * Register. Read the register into the d32 element then read ++ * out the bits using the bit elements. ++ */ ++typedef union hwcfg3_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /* GHWCFG3 */ ++ unsigned xfer_size_cntr_width:4; ++ unsigned packet_size_cntr_width:3; ++ unsigned otg_func:1; ++ unsigned i2c:1; ++ unsigned vendor_ctrl_if:1; ++ unsigned optional_features:1; ++ unsigned synch_reset_type:1; ++ unsigned adp_supp:1; ++ unsigned otg_enable_hsic:1; ++ unsigned bc_support:1; ++ unsigned otg_lpm_en:1; ++ unsigned dfifo_depth:16; ++ } b; ++} hwcfg3_data_t; ++ ++/** ++ * This union represents the bit fields in the User HW Config4 ++ * Register. Read the register into the d32 element then read ++ * out the bits using the bit elements. ++ */ ++typedef union hwcfg4_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned num_dev_perio_in_ep:4; ++ unsigned power_optimiz:1; ++ unsigned min_ahb_freq:1; ++ unsigned hiber:1; ++ unsigned xhiber:1; ++ unsigned reserved:6; ++ unsigned utmi_phy_data_width:2; ++ unsigned num_dev_mode_ctrl_ep:4; ++ unsigned iddig_filt_en:1; ++ unsigned vbus_valid_filt_en:1; ++ unsigned a_valid_filt_en:1; ++ unsigned b_valid_filt_en:1; ++ unsigned session_end_filt_en:1; ++ unsigned ded_fifo_en:1; ++ unsigned num_in_eps:4; ++ unsigned desc_dma:1; ++ unsigned desc_dma_dyn:1; ++ } b; ++} hwcfg4_data_t; ++ ++/** ++ * This union represents the bit fields of the Core LPM Configuration ++ * Register (GLPMCFG). Set the bits using bit fields then write ++ * the d32 value to the register. ++ */ ++typedef union glpmctl_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** LPM-Capable (LPMCap) (Device and Host) ++ * The application uses this bit to control ++ * the DWC_otg core LPM capabilities. ++ */ ++ unsigned lpm_cap_en:1; ++ /** LPM response programmed by application (AppL1Res) (Device) ++ * Handshake response to LPM token pre-programmed ++ * by device application software. ++ */ ++ unsigned appl_resp:1; ++ /** Host Initiated Resume Duration (HIRD) (Device and Host) ++ * In Host mode this field indicates the value of HIRD ++ * to be sent in an LPM transaction. ++ * In Device mode this field is updated with the ++ * Received LPM Token HIRD bmAttribute ++ * when an ACK/NYET/STALL response is sent ++ * to an LPM transaction. ++ */ ++ unsigned hird:4; ++ /** RemoteWakeEnable (bRemoteWake) (Device and Host) ++ * In Host mode this bit indicates the value of remote ++ * wake up to be sent in wIndex field of LPM transaction. ++ * In Device mode this field is updated with the ++ * Received LPM Token bRemoteWake bmAttribute ++ * when an ACK/NYET/STALL response is sent ++ * to an LPM transaction. ++ */ ++ unsigned rem_wkup_en:1; ++ /** Enable utmi_sleep_n (EnblSlpM) (Device and Host) ++ * The application uses this bit to control ++ * the utmi_sleep_n assertion to the PHY when in L1 state. ++ */ ++ unsigned en_utmi_sleep:1; ++ /** HIRD Threshold (HIRD_Thres) (Device and Host) ++ */ ++ unsigned hird_thres:5; ++ /** LPM Response (CoreL1Res) (Device and Host) ++ * In Host mode this bit contains handsake response to ++ * LPM transaction. ++ * In Device mode the response of the core to ++ * LPM transaction received is reflected in these two bits. ++ - 0x0 : ERROR (No handshake response) ++ - 0x1 : STALL ++ - 0x2 : NYET ++ - 0x3 : ACK ++ */ ++ unsigned lpm_resp:2; ++ /** Port Sleep Status (SlpSts) (Device and Host) ++ * This bit is set as long as a Sleep condition ++ * is present on the USB bus. ++ */ ++ unsigned prt_sleep_sts:1; ++ /** Sleep State Resume OK (L1ResumeOK) (Device and Host) ++ * Indicates that the application or host ++ * can start resume from Sleep state. ++ */ ++ unsigned sleep_state_resumeok:1; ++ /** LPM channel Index (LPM_Chnl_Indx) (Host) ++ * The channel number on which the LPM transaction ++ * has to be applied while sending ++ * an LPM transaction to the local device. ++ */ ++ unsigned lpm_chan_index:4; ++ /** LPM Retry Count (LPM_Retry_Cnt) (Host) ++ * Number host retries that would be performed ++ * if the device response was not valid response. ++ */ ++ unsigned retry_count:3; ++ /** Send LPM Transaction (SndLPM) (Host) ++ * When set by application software, ++ * an LPM transaction containing two tokens ++ * is sent. ++ */ ++ unsigned send_lpm:1; ++ /** LPM Retry status (LPM_RetryCnt_Sts) (Host) ++ * Number of LPM Host Retries still remaining ++ * to be transmitted for the current LPM sequence ++ */ ++ unsigned retry_count_sts:3; ++ unsigned reserved28_29:2; ++ /** In host mode once this bit is set, the host ++ * configures to drive the HSIC Idle state on the bus. ++ * It then waits for the device to initiate the Connect sequence. ++ * In device mode once this bit is set, the device waits for ++ * the HSIC Idle line state on the bus. Upon receving the Idle ++ * line state, it initiates the HSIC Connect sequence. ++ */ ++ unsigned hsic_connect:1; ++ /** This bit overrides and functionally inverts ++ * the if_select_hsic input port signal. ++ */ ++ unsigned inv_sel_hsic:1; ++ } b; ++} glpmcfg_data_t; ++ ++/** ++ * This union represents the bit fields of the Core ADP Timer, Control and ++ * Status Register (ADPTIMCTLSTS). Set the bits using bit fields then write ++ * the d32 value to the register. ++ */ ++typedef union adpctl_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** Probe Discharge (PRB_DSCHG) ++ * These bits set the times for TADP_DSCHG. ++ * These bits are defined as follows: ++ * 2'b00 - 4 msec ++ * 2'b01 - 8 msec ++ * 2'b10 - 16 msec ++ * 2'b11 - 32 msec ++ */ ++ unsigned prb_dschg:2; ++ /** Probe Delta (PRB_DELTA) ++ * These bits set the resolution for RTIM value. ++ * The bits are defined in units of 32 kHz clock cycles as follows: ++ * 2'b00 - 1 cycles ++ * 2'b01 - 2 cycles ++ * 2'b10 - 3 cycles ++ * 2'b11 - 4 cycles ++ * For example if this value is chosen to 2'b01, it means that RTIM ++ * increments for every 3(three) 32Khz clock cycles. ++ */ ++ unsigned prb_delta:2; ++ /** Probe Period (PRB_PER) ++ * These bits sets the TADP_PRD as shown in Figure 4 as follows: ++ * 2'b00 - 0.625 to 0.925 sec (typical 0.775 sec) ++ * 2'b01 - 1.25 to 1.85 sec (typical 1.55 sec) ++ * 2'b10 - 1.9 to 2.6 sec (typical 2.275 sec) ++ * 2'b11 - Reserved ++ */ ++ unsigned prb_per:2; ++ /** These bits capture the latest time it took for VBUS to ramp from ++ * VADP_SINK to VADP_PRB. ++ * 0x000 - 1 cycles ++ * 0x001 - 2 cycles ++ * 0x002 - 3 cycles ++ * etc ++ * 0x7FF - 2048 cycles ++ * A time of 1024 cycles at 32 kHz corresponds to a time of 32 msec. ++ */ ++ unsigned rtim:11; ++ /** Enable Probe (EnaPrb) ++ * When programmed to 1'b1, the core performs a probe operation. ++ * This bit is valid only if OTG_Ver = 1'b1. ++ */ ++ unsigned enaprb:1; ++ /** Enable Sense (EnaSns) ++ * When programmed to 1'b1, the core performs a Sense operation. ++ * This bit is valid only if OTG_Ver = 1'b1. ++ */ ++ unsigned enasns:1; ++ /** ADP Reset (ADPRes) ++ * When set, ADP controller is reset. ++ * This bit is valid only if OTG_Ver = 1'b1. ++ */ ++ unsigned adpres:1; ++ /** ADP Enable (ADPEn) ++ * When set, the core performs either ADP probing or sensing ++ * based on EnaPrb or EnaSns. ++ * This bit is valid only if OTG_Ver = 1'b1. ++ */ ++ unsigned adpen:1; ++ /** ADP Probe Interrupt (ADP_PRB_INT) ++ * When this bit is set, it means that the VBUS ++ * voltage is greater than VADP_PRB or VADP_PRB is reached. ++ * This bit is valid only if OTG_Ver = 1'b1. ++ */ ++ unsigned adp_prb_int:1; ++ /** ++ * ADP Sense Interrupt (ADP_SNS_INT) ++ * When this bit is set, it means that the VBUS voltage is greater than ++ * VADP_SNS value or VADP_SNS is reached. ++ * This bit is valid only if OTG_Ver = 1'b1. ++ */ ++ unsigned adp_sns_int:1; ++ /** ADP Tomeout Interrupt (ADP_TMOUT_INT) ++ * This bit is relevant only for an ADP probe. ++ * When this bit is set, it means that the ramp time has ++ * completed ie ADPCTL.RTIM has reached its terminal value ++ * of 0x7FF. This is a debug feature that allows software ++ * to read the ramp time after each cycle. ++ * This bit is valid only if OTG_Ver = 1'b1. ++ */ ++ unsigned adp_tmout_int:1; ++ /** ADP Probe Interrupt Mask (ADP_PRB_INT_MSK) ++ * When this bit is set, it unmasks the interrupt due to ADP_PRB_INT. ++ * This bit is valid only if OTG_Ver = 1'b1. ++ */ ++ unsigned adp_prb_int_msk:1; ++ /** ADP Sense Interrupt Mask (ADP_SNS_INT_MSK) ++ * When this bit is set, it unmasks the interrupt due to ADP_SNS_INT. ++ * This bit is valid only if OTG_Ver = 1'b1. ++ */ ++ unsigned adp_sns_int_msk:1; ++ /** ADP Timoeout Interrupt Mask (ADP_TMOUT_MSK) ++ * When this bit is set, it unmasks the interrupt due to ADP_TMOUT_INT. ++ * This bit is valid only if OTG_Ver = 1'b1. ++ */ ++ unsigned adp_tmout_int_msk:1; ++ /** Access Request ++ * 2'b00 - Read/Write Valid (updated by the core) ++ * 2'b01 - Read ++ * 2'b00 - Write ++ * 2'b00 - Reserved ++ */ ++ unsigned ar:2; ++ /** Reserved */ ++ unsigned reserved29_31:3; ++ } b; ++} adpctl_data_t; ++ ++//////////////////////////////////////////// ++// Device Registers ++/** ++ * Device Global Registers. Offsets 800h-BFFh ++ * ++ * The following structures define the size and relative field offsets ++ * for the Device Mode Registers. ++ * ++ * These registers are visible only in Device mode and must not be ++ * accessed in Host mode, as the results are unknown. ++ */ ++typedef struct dwc_otg_dev_global_regs { ++ /** Device Configuration Register. Offset 800h */ ++ volatile uint32_t dcfg; ++ /** Device Control Register. Offset: 804h */ ++ volatile uint32_t dctl; ++ /** Device Status Register (Read Only). Offset: 808h */ ++ volatile uint32_t dsts; ++ /** Reserved. Offset: 80Ch */ ++ uint32_t unused; ++ /** Device IN Endpoint Common Interrupt Mask ++ * Register. Offset: 810h */ ++ volatile uint32_t diepmsk; ++ /** Device OUT Endpoint Common Interrupt Mask ++ * Register. Offset: 814h */ ++ volatile uint32_t doepmsk; ++ /** Device All Endpoints Interrupt Register. Offset: 818h */ ++ volatile uint32_t daint; ++ /** Device All Endpoints Interrupt Mask Register. Offset: ++ * 81Ch */ ++ volatile uint32_t daintmsk; ++ /** Device IN Token Queue Read Register-1 (Read Only). ++ * Offset: 820h */ ++ volatile uint32_t dtknqr1; ++ /** Device IN Token Queue Read Register-2 (Read Only). ++ * Offset: 824h */ ++ volatile uint32_t dtknqr2; ++ /** Device VBUS discharge Register. Offset: 828h */ ++ volatile uint32_t dvbusdis; ++ /** Device VBUS Pulse Register. Offset: 82Ch */ ++ volatile uint32_t dvbuspulse; ++ /** Device IN Token Queue Read Register-3 (Read Only). / ++ * Device Thresholding control register (Read/Write) ++ * Offset: 830h */ ++ volatile uint32_t dtknqr3_dthrctl; ++ /** Device IN Token Queue Read Register-4 (Read Only). / ++ * Device IN EPs empty Inr. Mask Register (Read/Write) ++ * Offset: 834h */ ++ volatile uint32_t dtknqr4_fifoemptymsk; ++ /** Device Each Endpoint Interrupt Register (Read Only). / ++ * Offset: 838h */ ++ volatile uint32_t deachint; ++ /** Device Each Endpoint Interrupt mask Register (Read/Write). / ++ * Offset: 83Ch */ ++ volatile uint32_t deachintmsk; ++ /** Device Each In Endpoint Interrupt mask Register (Read/Write). / ++ * Offset: 840h */ ++ volatile uint32_t diepeachintmsk[MAX_EPS_CHANNELS]; ++ /** Device Each Out Endpoint Interrupt mask Register (Read/Write). / ++ * Offset: 880h */ ++ volatile uint32_t doepeachintmsk[MAX_EPS_CHANNELS]; ++} dwc_otg_device_global_regs_t; ++ ++/** ++ * This union represents the bit fields in the Device Configuration ++ * Register. Read the register into the d32 member then ++ * set/clear the bits using the bit elements. Write the ++ * d32 member to the dcfg register. ++ */ ++typedef union dcfg_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** Device Speed */ ++ unsigned devspd:2; ++ /** Non Zero Length Status OUT Handshake */ ++ unsigned nzstsouthshk:1; ++#define DWC_DCFG_SEND_STALL 1 ++ ++ unsigned ena32khzs:1; ++ /** Device Addresses */ ++ unsigned devaddr:7; ++ /** Periodic Frame Interval */ ++ unsigned perfrint:2; ++#define DWC_DCFG_FRAME_INTERVAL_80 0 ++#define DWC_DCFG_FRAME_INTERVAL_85 1 ++#define DWC_DCFG_FRAME_INTERVAL_90 2 ++#define DWC_DCFG_FRAME_INTERVAL_95 3 ++ ++ /** Enable Device OUT NAK for bulk in DDMA mode */ ++ unsigned endevoutnak:1; ++ ++ unsigned reserved14_17:4; ++ /** In Endpoint Mis-match count */ ++ unsigned epmscnt:5; ++ /** Enable Descriptor DMA in Device mode */ ++ unsigned descdma:1; ++ unsigned perschintvl:2; ++ unsigned resvalid:6; ++ } b; ++} dcfg_data_t; ++ ++/** ++ * This union represents the bit fields in the Device Control ++ * Register. Read the register into the d32 member then ++ * set/clear the bits using the bit elements. ++ */ ++typedef union dctl_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** Remote Wakeup */ ++ unsigned rmtwkupsig:1; ++ /** Soft Disconnect */ ++ unsigned sftdiscon:1; ++ /** Global Non-Periodic IN NAK Status */ ++ unsigned gnpinnaksts:1; ++ /** Global OUT NAK Status */ ++ unsigned goutnaksts:1; ++ /** Test Control */ ++ unsigned tstctl:3; ++ /** Set Global Non-Periodic IN NAK */ ++ unsigned sgnpinnak:1; ++ /** Clear Global Non-Periodic IN NAK */ ++ unsigned cgnpinnak:1; ++ /** Set Global OUT NAK */ ++ unsigned sgoutnak:1; ++ /** Clear Global OUT NAK */ ++ unsigned cgoutnak:1; ++ /** Power-On Programming Done */ ++ unsigned pwronprgdone:1; ++ /** Reserved */ ++ unsigned reserved:1; ++ /** Global Multi Count */ ++ unsigned gmc:2; ++ /** Ignore Frame Number for ISOC EPs */ ++ unsigned ifrmnum:1; ++ /** NAK on Babble */ ++ unsigned nakonbble:1; ++ /** Enable Continue on BNA */ ++ unsigned encontonbna:1; ++ ++ unsigned reserved18_31:14; ++ } b; ++} dctl_data_t; ++ ++/** ++ * This union represents the bit fields in the Device Status ++ * Register. Read the register into the d32 member then ++ * set/clear the bits using the bit elements. ++ */ ++typedef union dsts_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** Suspend Status */ ++ unsigned suspsts:1; ++ /** Enumerated Speed */ ++ unsigned enumspd:2; ++#define DWC_DSTS_ENUMSPD_HS_PHY_30MHZ_OR_60MHZ 0 ++#define DWC_DSTS_ENUMSPD_FS_PHY_30MHZ_OR_60MHZ 1 ++#define DWC_DSTS_ENUMSPD_LS_PHY_6MHZ 2 ++#define DWC_DSTS_ENUMSPD_FS_PHY_48MHZ 3 ++ /** Erratic Error */ ++ unsigned errticerr:1; ++ unsigned reserved4_7:4; ++ /** Frame or Microframe Number of the received SOF */ ++ unsigned soffn:14; ++ unsigned reserved22_31:10; ++ } b; ++} dsts_data_t; ++ ++/** ++ * This union represents the bit fields in the Device IN EP Interrupt ++ * Register and the Device IN EP Common Mask Register. ++ * ++ * - Read the register into the d32 member then set/clear the ++ * bits using the bit elements. ++ */ ++typedef union diepint_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** Transfer complete mask */ ++ unsigned xfercompl:1; ++ /** Endpoint disable mask */ ++ unsigned epdisabled:1; ++ /** AHB Error mask */ ++ unsigned ahberr:1; ++ /** TimeOUT Handshake mask (non-ISOC EPs) */ ++ unsigned timeout:1; ++ /** IN Token received with TxF Empty mask */ ++ unsigned intktxfemp:1; ++ /** IN Token Received with EP mismatch mask */ ++ unsigned intknepmis:1; ++ /** IN Endpoint NAK Effective mask */ ++ unsigned inepnakeff:1; ++ /** Reserved */ ++ unsigned emptyintr:1; ++ ++ unsigned txfifoundrn:1; ++ ++ /** BNA Interrupt mask */ ++ unsigned bna:1; ++ ++ unsigned reserved10_12:3; ++ /** BNA Interrupt mask */ ++ unsigned nak:1; ++ ++ unsigned reserved14_31:18; ++ } b; ++} diepint_data_t; ++ ++/** ++ * This union represents the bit fields in the Device IN EP ++ * Common/Dedicated Interrupt Mask Register. ++ */ ++typedef union diepint_data diepmsk_data_t; ++ ++/** ++ * This union represents the bit fields in the Device OUT EP Interrupt ++ * Registerand Device OUT EP Common Interrupt Mask Register. ++ * ++ * - Read the register into the d32 member then set/clear the ++ * bits using the bit elements. ++ */ ++typedef union doepint_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** Transfer complete */ ++ unsigned xfercompl:1; ++ /** Endpoint disable */ ++ unsigned epdisabled:1; ++ /** AHB Error */ ++ unsigned ahberr:1; ++ /** Setup Phase Done (contorl EPs) */ ++ unsigned setup:1; ++ /** OUT Token Received when Endpoint Disabled */ ++ unsigned outtknepdis:1; ++ ++ unsigned stsphsercvd:1; ++ /** Back-to-Back SETUP Packets Received */ ++ unsigned back2backsetup:1; ++ ++ unsigned reserved7:1; ++ /** OUT packet Error */ ++ unsigned outpkterr:1; ++ /** BNA Interrupt */ ++ unsigned bna:1; ++ ++ unsigned reserved10:1; ++ /** Packet Drop Status */ ++ unsigned pktdrpsts:1; ++ /** Babble Interrupt */ ++ unsigned babble:1; ++ /** NAK Interrupt */ ++ unsigned nak:1; ++ /** NYET Interrupt */ ++ unsigned nyet:1; ++ /** Bit indicating setup packet received */ ++ unsigned sr:1; ++ ++ unsigned reserved16_31:16; ++ } b; ++} doepint_data_t; ++ ++/** ++ * This union represents the bit fields in the Device OUT EP ++ * Common/Dedicated Interrupt Mask Register. ++ */ ++typedef union doepint_data doepmsk_data_t; ++ ++/** ++ * This union represents the bit fields in the Device All EP Interrupt ++ * and Mask Registers. ++ * - Read the register into the d32 member then set/clear the ++ * bits using the bit elements. ++ */ ++typedef union daint_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** IN Endpoint bits */ ++ unsigned in:16; ++ /** OUT Endpoint bits */ ++ unsigned out:16; ++ } ep; ++ struct { ++ /** IN Endpoint bits */ ++ unsigned inep0:1; ++ unsigned inep1:1; ++ unsigned inep2:1; ++ unsigned inep3:1; ++ unsigned inep4:1; ++ unsigned inep5:1; ++ unsigned inep6:1; ++ unsigned inep7:1; ++ unsigned inep8:1; ++ unsigned inep9:1; ++ unsigned inep10:1; ++ unsigned inep11:1; ++ unsigned inep12:1; ++ unsigned inep13:1; ++ unsigned inep14:1; ++ unsigned inep15:1; ++ /** OUT Endpoint bits */ ++ unsigned outep0:1; ++ unsigned outep1:1; ++ unsigned outep2:1; ++ unsigned outep3:1; ++ unsigned outep4:1; ++ unsigned outep5:1; ++ unsigned outep6:1; ++ unsigned outep7:1; ++ unsigned outep8:1; ++ unsigned outep9:1; ++ unsigned outep10:1; ++ unsigned outep11:1; ++ unsigned outep12:1; ++ unsigned outep13:1; ++ unsigned outep14:1; ++ unsigned outep15:1; ++ } b; ++} daint_data_t; ++ ++/** ++ * This union represents the bit fields in the Device IN Token Queue ++ * Read Registers. ++ * - Read the register into the d32 member. ++ * - READ-ONLY Register ++ */ ++typedef union dtknq1_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** In Token Queue Write Pointer */ ++ unsigned intknwptr:5; ++ /** Reserved */ ++ unsigned reserved05_06:2; ++ /** write pointer has wrapped. */ ++ unsigned wrap_bit:1; ++ /** EP Numbers of IN Tokens 0 ... 4 */ ++ unsigned epnums0_5:24; ++ } b; ++} dtknq1_data_t; ++ ++/** ++ * This union represents Threshold control Register ++ * - Read and write the register into the d32 member. ++ * - READ-WRITABLE Register ++ */ ++typedef union dthrctl_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** non ISO Tx Thr. Enable */ ++ unsigned non_iso_thr_en:1; ++ /** ISO Tx Thr. Enable */ ++ unsigned iso_thr_en:1; ++ /** Tx Thr. Length */ ++ unsigned tx_thr_len:9; ++ /** AHB Threshold ratio */ ++ unsigned ahb_thr_ratio:2; ++ /** Reserved */ ++ unsigned reserved13_15:3; ++ /** Rx Thr. Enable */ ++ unsigned rx_thr_en:1; ++ /** Rx Thr. Length */ ++ unsigned rx_thr_len:9; ++ unsigned reserved26:1; ++ /** Arbiter Parking Enable*/ ++ unsigned arbprken:1; ++ /** Reserved */ ++ unsigned reserved28_31:4; ++ } b; ++} dthrctl_data_t; ++ ++/** ++ * Device Logical IN Endpoint-Specific Registers. Offsets ++ * 900h-AFCh ++ * ++ * There will be one set of endpoint registers per logical endpoint ++ * implemented. ++ * ++ * These registers are visible only in Device mode and must not be ++ * accessed in Host mode, as the results are unknown. ++ */ ++typedef struct dwc_otg_dev_in_ep_regs { ++ /** Device IN Endpoint Control Register. Offset:900h + ++ * (ep_num * 20h) + 00h */ ++ volatile uint32_t diepctl; ++ /** Reserved. Offset:900h + (ep_num * 20h) + 04h */ ++ uint32_t reserved04; ++ /** Device IN Endpoint Interrupt Register. Offset:900h + ++ * (ep_num * 20h) + 08h */ ++ volatile uint32_t diepint; ++ /** Reserved. Offset:900h + (ep_num * 20h) + 0Ch */ ++ uint32_t reserved0C; ++ /** Device IN Endpoint Transfer Size ++ * Register. Offset:900h + (ep_num * 20h) + 10h */ ++ volatile uint32_t dieptsiz; ++ /** Device IN Endpoint DMA Address Register. Offset:900h + ++ * (ep_num * 20h) + 14h */ ++ volatile uint32_t diepdma; ++ /** Device IN Endpoint Transmit FIFO Status Register. Offset:900h + ++ * (ep_num * 20h) + 18h */ ++ volatile uint32_t dtxfsts; ++ /** Device IN Endpoint DMA Buffer Register. Offset:900h + ++ * (ep_num * 20h) + 1Ch */ ++ volatile uint32_t diepdmab; ++} dwc_otg_dev_in_ep_regs_t; ++ ++/** ++ * Device Logical OUT Endpoint-Specific Registers. Offsets: ++ * B00h-CFCh ++ * ++ * There will be one set of endpoint registers per logical endpoint ++ * implemented. ++ * ++ * These registers are visible only in Device mode and must not be ++ * accessed in Host mode, as the results are unknown. ++ */ ++typedef struct dwc_otg_dev_out_ep_regs { ++ /** Device OUT Endpoint Control Register. Offset:B00h + ++ * (ep_num * 20h) + 00h */ ++ volatile uint32_t doepctl; ++ /** Reserved. Offset:B00h + (ep_num * 20h) + 04h */ ++ uint32_t reserved04; ++ /** Device OUT Endpoint Interrupt Register. Offset:B00h + ++ * (ep_num * 20h) + 08h */ ++ volatile uint32_t doepint; ++ /** Reserved. Offset:B00h + (ep_num * 20h) + 0Ch */ ++ uint32_t reserved0C; ++ /** Device OUT Endpoint Transfer Size Register. Offset: ++ * B00h + (ep_num * 20h) + 10h */ ++ volatile uint32_t doeptsiz; ++ /** Device OUT Endpoint DMA Address Register. Offset:B00h ++ * + (ep_num * 20h) + 14h */ ++ volatile uint32_t doepdma; ++ /** Reserved. Offset:B00h + * (ep_num * 20h) + 18h */ ++ uint32_t unused; ++ /** Device OUT Endpoint DMA Buffer Register. Offset:B00h ++ * + (ep_num * 20h) + 1Ch */ ++ uint32_t doepdmab; ++} dwc_otg_dev_out_ep_regs_t; ++ ++/** ++ * This union represents the bit fields in the Device EP Control ++ * Register. Read the register into the d32 member then ++ * set/clear the bits using the bit elements. ++ */ ++typedef union depctl_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** Maximum Packet Size ++ * IN/OUT EPn ++ * IN/OUT EP0 - 2 bits ++ * 2'b00: 64 Bytes ++ * 2'b01: 32 ++ * 2'b10: 16 ++ * 2'b11: 8 */ ++ unsigned mps:11; ++#define DWC_DEP0CTL_MPS_64 0 ++#define DWC_DEP0CTL_MPS_32 1 ++#define DWC_DEP0CTL_MPS_16 2 ++#define DWC_DEP0CTL_MPS_8 3 ++ ++ /** Next Endpoint ++ * IN EPn/IN EP0 ++ * OUT EPn/OUT EP0 - reserved */ ++ unsigned nextep:4; ++ ++ /** USB Active Endpoint */ ++ unsigned usbactep:1; ++ ++ /** Endpoint DPID (INTR/Bulk IN and OUT endpoints) ++ * This field contains the PID of the packet going to ++ * be received or transmitted on this endpoint. The ++ * application should program the PID of the first ++ * packet going to be received or transmitted on this ++ * endpoint , after the endpoint is ++ * activated. Application use the SetD1PID and ++ * SetD0PID fields of this register to program either ++ * D0 or D1 PID. ++ * ++ * The encoding for this field is ++ * - 0: D0 ++ * - 1: D1 ++ */ ++ unsigned dpid:1; ++ ++ /** NAK Status */ ++ unsigned naksts:1; ++ ++ /** Endpoint Type ++ * 2'b00: Control ++ * 2'b01: Isochronous ++ * 2'b10: Bulk ++ * 2'b11: Interrupt */ ++ unsigned eptype:2; ++ ++ /** Snoop Mode ++ * OUT EPn/OUT EP0 ++ * IN EPn/IN EP0 - reserved */ ++ unsigned snp:1; ++ ++ /** Stall Handshake */ ++ unsigned stall:1; ++ ++ /** Tx Fifo Number ++ * IN EPn/IN EP0 ++ * OUT EPn/OUT EP0 - reserved */ ++ unsigned txfnum:4; ++ ++ /** Clear NAK */ ++ unsigned cnak:1; ++ /** Set NAK */ ++ unsigned snak:1; ++ /** Set DATA0 PID (INTR/Bulk IN and OUT endpoints) ++ * Writing to this field sets the Endpoint DPID (DPID) ++ * field in this register to DATA0. Set Even ++ * (micro)frame (SetEvenFr) (ISO IN and OUT Endpoints) ++ * Writing to this field sets the Even/Odd ++ * (micro)frame (EO_FrNum) field to even (micro) ++ * frame. ++ */ ++ unsigned setd0pid:1; ++ /** Set DATA1 PID (INTR/Bulk IN and OUT endpoints) ++ * Writing to this field sets the Endpoint DPID (DPID) ++ * field in this register to DATA1 Set Odd ++ * (micro)frame (SetOddFr) (ISO IN and OUT Endpoints) ++ * Writing to this field sets the Even/Odd ++ * (micro)frame (EO_FrNum) field to odd (micro) frame. ++ */ ++ unsigned setd1pid:1; ++ ++ /** Endpoint Disable */ ++ unsigned epdis:1; ++ /** Endpoint Enable */ ++ unsigned epena:1; ++ } b; ++} depctl_data_t; ++ ++/** ++ * This union represents the bit fields in the Device EP Transfer ++ * Size Register. Read the register into the d32 member then ++ * set/clear the bits using the bit elements. ++ */ ++typedef union deptsiz_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** Transfer size */ ++ unsigned xfersize:19; ++/** Max packet count for EP (pow(2,10)-1) */ ++#define MAX_PKT_CNT 1023 ++ /** Packet Count */ ++ unsigned pktcnt:10; ++ /** Multi Count - Periodic IN endpoints */ ++ unsigned mc:2; ++ unsigned reserved:1; ++ } b; ++} deptsiz_data_t; ++ ++/** ++ * This union represents the bit fields in the Device EP 0 Transfer ++ * Size Register. Read the register into the d32 member then ++ * set/clear the bits using the bit elements. ++ */ ++typedef union deptsiz0_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** Transfer size */ ++ unsigned xfersize:7; ++ /** Reserved */ ++ unsigned reserved7_18:12; ++ /** Packet Count */ ++ unsigned pktcnt:2; ++ /** Reserved */ ++ unsigned reserved21_28:8; ++ /**Setup Packet Count (DOEPTSIZ0 Only) */ ++ unsigned supcnt:2; ++ unsigned reserved31; ++ } b; ++} deptsiz0_data_t; ++ ++///////////////////////////////////////////////// ++// DMA Descriptor Specific Structures ++// ++ ++/** Buffer status definitions */ ++ ++#define BS_HOST_READY 0x0 ++#define BS_DMA_BUSY 0x1 ++#define BS_DMA_DONE 0x2 ++#define BS_HOST_BUSY 0x3 ++ ++/** Receive/Transmit status definitions */ ++ ++#define RTS_SUCCESS 0x0 ++#define RTS_BUFFLUSH 0x1 ++#define RTS_RESERVED 0x2 ++#define RTS_BUFERR 0x3 ++ ++/** ++ * This union represents the bit fields in the DMA Descriptor ++ * status quadlet. Read the quadlet into the d32 member then ++ * set/clear the bits using the bit, b_iso_out and ++ * b_iso_in elements. ++ */ ++typedef union dev_dma_desc_sts { ++ /** raw register data */ ++ uint32_t d32; ++ /** quadlet bits */ ++ struct { ++ /** Received number of bytes */ ++ unsigned bytes:16; ++ /** NAK bit - only for OUT EPs */ ++ unsigned nak:1; ++ unsigned reserved17_22:6; ++ /** Multiple Transfer - only for OUT EPs */ ++ unsigned mtrf:1; ++ /** Setup Packet received - only for OUT EPs */ ++ unsigned sr:1; ++ /** Interrupt On Complete */ ++ unsigned ioc:1; ++ /** Short Packet */ ++ unsigned sp:1; ++ /** Last */ ++ unsigned l:1; ++ /** Receive Status */ ++ unsigned sts:2; ++ /** Buffer Status */ ++ unsigned bs:2; ++ } b; ++ ++//#ifdef DWC_EN_ISOC ++ /** iso out quadlet bits */ ++ struct { ++ /** Received number of bytes */ ++ unsigned rxbytes:11; ++ ++ unsigned reserved11:1; ++ /** Frame Number */ ++ unsigned framenum:11; ++ /** Received ISO Data PID */ ++ unsigned pid:2; ++ /** Interrupt On Complete */ ++ unsigned ioc:1; ++ /** Short Packet */ ++ unsigned sp:1; ++ /** Last */ ++ unsigned l:1; ++ /** Receive Status */ ++ unsigned rxsts:2; ++ /** Buffer Status */ ++ unsigned bs:2; ++ } b_iso_out; ++ ++ /** iso in quadlet bits */ ++ struct { ++ /** Transmited number of bytes */ ++ unsigned txbytes:12; ++ /** Frame Number */ ++ unsigned framenum:11; ++ /** Transmited ISO Data PID */ ++ unsigned pid:2; ++ /** Interrupt On Complete */ ++ unsigned ioc:1; ++ /** Short Packet */ ++ unsigned sp:1; ++ /** Last */ ++ unsigned l:1; ++ /** Transmit Status */ ++ unsigned txsts:2; ++ /** Buffer Status */ ++ unsigned bs:2; ++ } b_iso_in; ++//#endif /* DWC_EN_ISOC */ ++} dev_dma_desc_sts_t; ++ ++/** ++ * DMA Descriptor structure ++ * ++ * DMA Descriptor structure contains two quadlets: ++ * Status quadlet and Data buffer pointer. ++ */ ++typedef struct dwc_otg_dev_dma_desc { ++ /** DMA Descriptor status quadlet */ ++ dev_dma_desc_sts_t status; ++ /** DMA Descriptor data buffer pointer */ ++ uint32_t buf; ++} dwc_otg_dev_dma_desc_t; ++ ++/** ++ * The dwc_otg_dev_if structure contains information needed to manage ++ * the DWC_otg controller acting in device mode. It represents the ++ * programming view of the device-specific aspects of the controller. ++ */ ++typedef struct dwc_otg_dev_if { ++ /** Pointer to device Global registers. ++ * Device Global Registers starting at offset 800h ++ */ ++ dwc_otg_device_global_regs_t *dev_global_regs; ++#define DWC_DEV_GLOBAL_REG_OFFSET 0x800 ++ ++ /** ++ * Device Logical IN Endpoint-Specific Registers 900h-AFCh ++ */ ++ dwc_otg_dev_in_ep_regs_t *in_ep_regs[MAX_EPS_CHANNELS]; ++#define DWC_DEV_IN_EP_REG_OFFSET 0x900 ++#define DWC_EP_REG_OFFSET 0x20 ++ ++ /** Device Logical OUT Endpoint-Specific Registers B00h-CFCh */ ++ dwc_otg_dev_out_ep_regs_t *out_ep_regs[MAX_EPS_CHANNELS]; ++#define DWC_DEV_OUT_EP_REG_OFFSET 0xB00 ++ ++ /* Device configuration information */ ++ uint8_t speed; /**< Device Speed 0: Unknown, 1: LS, 2:FS, 3: HS */ ++ uint8_t num_in_eps; /**< Number # of Tx EP range: 0-15 exept ep0 */ ++ uint8_t num_out_eps; /**< Number # of Rx EP range: 0-15 exept ep 0*/ ++ ++ /** Size of periodic FIFOs (Bytes) */ ++ uint16_t perio_tx_fifo_size[MAX_PERIO_FIFOS]; ++ ++ /** Size of Tx FIFOs (Bytes) */ ++ uint16_t tx_fifo_size[MAX_TX_FIFOS]; ++ ++ /** Thresholding enable flags and length varaiables **/ ++ uint16_t rx_thr_en; ++ uint16_t iso_tx_thr_en; ++ uint16_t non_iso_tx_thr_en; ++ ++ uint16_t rx_thr_length; ++ uint16_t tx_thr_length; ++ ++ /** ++ * Pointers to the DMA Descriptors for EP0 Control ++ * transfers (virtual and physical) ++ */ ++ ++ /** 2 descriptors for SETUP packets */ ++ dwc_dma_t dma_setup_desc_addr[2]; ++ dwc_otg_dev_dma_desc_t *setup_desc_addr[2]; ++ ++ /** Pointer to Descriptor with latest SETUP packet */ ++ dwc_otg_dev_dma_desc_t *psetup; ++ ++ /** Index of current SETUP handler descriptor */ ++ uint32_t setup_desc_index; ++ ++ /** Descriptor for Data In or Status In phases */ ++ dwc_dma_t dma_in_desc_addr; ++ dwc_otg_dev_dma_desc_t *in_desc_addr; ++ ++ /** Descriptor for Data Out or Status Out phases */ ++ dwc_dma_t dma_out_desc_addr; ++ dwc_otg_dev_dma_desc_t *out_desc_addr; ++ ++ /** Setup Packet Detected - if set clear NAK when queueing */ ++ uint32_t spd; ++ /** Isoc ep pointer on which incomplete happens */ ++ void *isoc_ep; ++ ++} dwc_otg_dev_if_t; ++ ++///////////////////////////////////////////////// ++// Host Mode Register Structures ++// ++/** ++ * The Host Global Registers structure defines the size and relative ++ * field offsets for the Host Mode Global Registers. Host Global ++ * Registers offsets 400h-7FFh. ++*/ ++typedef struct dwc_otg_host_global_regs { ++ /** Host Configuration Register. Offset: 400h */ ++ volatile uint32_t hcfg; ++ /** Host Frame Interval Register. Offset: 404h */ ++ volatile uint32_t hfir; ++ /** Host Frame Number / Frame Remaining Register. Offset: 408h */ ++ volatile uint32_t hfnum; ++ /** Reserved. Offset: 40Ch */ ++ uint32_t reserved40C; ++ /** Host Periodic Transmit FIFO/ Queue Status Register. Offset: 410h */ ++ volatile uint32_t hptxsts; ++ /** Host All Channels Interrupt Register. Offset: 414h */ ++ volatile uint32_t haint; ++ /** Host All Channels Interrupt Mask Register. Offset: 418h */ ++ volatile uint32_t haintmsk; ++ /** Host Frame List Base Address Register . Offset: 41Ch */ ++ volatile uint32_t hflbaddr; ++} dwc_otg_host_global_regs_t; ++ ++/** ++ * This union represents the bit fields in the Host Configuration Register. ++ * Read the register into the d32 member then set/clear the bits using ++ * the bit elements. Write the d32 member to the hcfg register. ++ */ ++typedef union hcfg_data { ++ /** raw register data */ ++ uint32_t d32; ++ ++ /** register bits */ ++ struct { ++ /** FS/LS Phy Clock Select */ ++ unsigned fslspclksel:2; ++#define DWC_HCFG_30_60_MHZ 0 ++#define DWC_HCFG_48_MHZ 1 ++#define DWC_HCFG_6_MHZ 2 ++ ++ /** FS/LS Only Support */ ++ unsigned fslssupp:1; ++ unsigned reserved3_6:4; ++ /** Enable 32-KHz Suspend Mode */ ++ unsigned ena32khzs:1; ++ /** Resume Validation Periiod */ ++ unsigned resvalid:8; ++ unsigned reserved16_22:7; ++ /** Enable Scatter/gather DMA in Host mode */ ++ unsigned descdma:1; ++ /** Frame List Entries */ ++ unsigned frlisten:2; ++ /** Enable Periodic Scheduling */ ++ unsigned perschedena:1; ++ unsigned reserved27_30:4; ++ unsigned modechtimen:1; ++ } b; ++} hcfg_data_t; ++ ++/** ++ * This union represents the bit fields in the Host Frame Remaing/Number ++ * Register. ++ */ ++typedef union hfir_data { ++ /** raw register data */ ++ uint32_t d32; ++ ++ /** register bits */ ++ struct { ++ unsigned frint:16; ++ unsigned hfirrldctrl:1; ++ unsigned reserved:15; ++ } b; ++} hfir_data_t; ++ ++/** ++ * This union represents the bit fields in the Host Frame Remaing/Number ++ * Register. ++ */ ++typedef union hfnum_data { ++ /** raw register data */ ++ uint32_t d32; ++ ++ /** register bits */ ++ struct { ++ unsigned frnum:16; ++#define DWC_HFNUM_MAX_FRNUM 0x3FFF ++ unsigned frrem:16; ++ } b; ++} hfnum_data_t; ++ ++typedef union hptxsts_data { ++ /** raw register data */ ++ uint32_t d32; ++ ++ /** register bits */ ++ struct { ++ unsigned ptxfspcavail:16; ++ unsigned ptxqspcavail:8; ++ /** Top of the Periodic Transmit Request Queue ++ * - bit 24 - Terminate (last entry for the selected channel) ++ * - bits 26:25 - Token Type ++ * - 2'b00 - Zero length ++ * - 2'b01 - Ping ++ * - 2'b10 - Disable ++ * - bits 30:27 - Channel Number ++ * - bit 31 - Odd/even microframe ++ */ ++ unsigned ptxqtop_terminate:1; ++ unsigned ptxqtop_token:2; ++ unsigned ptxqtop_chnum:4; ++ unsigned ptxqtop_odd:1; ++ } b; ++} hptxsts_data_t; ++ ++/** ++ * This union represents the bit fields in the Host Port Control and Status ++ * Register. Read the register into the d32 member then set/clear the ++ * bits using the bit elements. Write the d32 member to the ++ * hprt0 register. ++ */ ++typedef union hprt0_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned prtconnsts:1; ++ unsigned prtconndet:1; ++ unsigned prtena:1; ++ unsigned prtenchng:1; ++ unsigned prtovrcurract:1; ++ unsigned prtovrcurrchng:1; ++ unsigned prtres:1; ++ unsigned prtsusp:1; ++ unsigned prtrst:1; ++ unsigned reserved9:1; ++ unsigned prtlnsts:2; ++ unsigned prtpwr:1; ++ unsigned prttstctl:4; ++ unsigned prtspd:2; ++#define DWC_HPRT0_PRTSPD_HIGH_SPEED 0 ++#define DWC_HPRT0_PRTSPD_FULL_SPEED 1 ++#define DWC_HPRT0_PRTSPD_LOW_SPEED 2 ++ unsigned reserved19_31:13; ++ } b; ++} hprt0_data_t; ++ ++/** ++ * This union represents the bit fields in the Host All Interrupt ++ * Register. ++ */ ++typedef union haint_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned ch0:1; ++ unsigned ch1:1; ++ unsigned ch2:1; ++ unsigned ch3:1; ++ unsigned ch4:1; ++ unsigned ch5:1; ++ unsigned ch6:1; ++ unsigned ch7:1; ++ unsigned ch8:1; ++ unsigned ch9:1; ++ unsigned ch10:1; ++ unsigned ch11:1; ++ unsigned ch12:1; ++ unsigned ch13:1; ++ unsigned ch14:1; ++ unsigned ch15:1; ++ unsigned reserved:16; ++ } b; ++ ++ struct { ++ unsigned chint:16; ++ unsigned reserved:16; ++ } b2; ++} haint_data_t; ++ ++/** ++ * This union represents the bit fields in the Host All Interrupt ++ * Register. ++ */ ++typedef union haintmsk_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned ch0:1; ++ unsigned ch1:1; ++ unsigned ch2:1; ++ unsigned ch3:1; ++ unsigned ch4:1; ++ unsigned ch5:1; ++ unsigned ch6:1; ++ unsigned ch7:1; ++ unsigned ch8:1; ++ unsigned ch9:1; ++ unsigned ch10:1; ++ unsigned ch11:1; ++ unsigned ch12:1; ++ unsigned ch13:1; ++ unsigned ch14:1; ++ unsigned ch15:1; ++ unsigned reserved:16; ++ } b; ++ ++ struct { ++ unsigned chint:16; ++ unsigned reserved:16; ++ } b2; ++} haintmsk_data_t; ++ ++/** ++ * Host Channel Specific Registers. 500h-5FCh ++ */ ++typedef struct dwc_otg_hc_regs { ++ /** Host Channel 0 Characteristic Register. Offset: 500h + (chan_num * 20h) + 00h */ ++ volatile uint32_t hcchar; ++ /** Host Channel 0 Split Control Register. Offset: 500h + (chan_num * 20h) + 04h */ ++ volatile uint32_t hcsplt; ++ /** Host Channel 0 Interrupt Register. Offset: 500h + (chan_num * 20h) + 08h */ ++ volatile uint32_t hcint; ++ /** Host Channel 0 Interrupt Mask Register. Offset: 500h + (chan_num * 20h) + 0Ch */ ++ volatile uint32_t hcintmsk; ++ /** Host Channel 0 Transfer Size Register. Offset: 500h + (chan_num * 20h) + 10h */ ++ volatile uint32_t hctsiz; ++ /** Host Channel 0 DMA Address Register. Offset: 500h + (chan_num * 20h) + 14h */ ++ volatile uint32_t hcdma; ++ volatile uint32_t reserved; ++ /** Host Channel 0 DMA Buffer Address Register. Offset: 500h + (chan_num * 20h) + 1Ch */ ++ volatile uint32_t hcdmab; ++} dwc_otg_hc_regs_t; ++ ++/** ++ * This union represents the bit fields in the Host Channel Characteristics ++ * Register. Read the register into the d32 member then set/clear the ++ * bits using the bit elements. Write the d32 member to the ++ * hcchar register. ++ */ ++typedef union hcchar_data { ++ /** raw register data */ ++ uint32_t d32; ++ ++ /** register bits */ ++ struct { ++ /** Maximum packet size in bytes */ ++ unsigned mps:11; ++ ++ /** Endpoint number */ ++ unsigned epnum:4; ++ ++ /** 0: OUT, 1: IN */ ++ unsigned epdir:1; ++ ++ unsigned reserved:1; ++ ++ /** 0: Full/high speed device, 1: Low speed device */ ++ unsigned lspddev:1; ++ ++ /** 0: Control, 1: Isoc, 2: Bulk, 3: Intr */ ++ unsigned eptype:2; ++ ++ /** Packets per frame for periodic transfers. 0 is reserved. */ ++ unsigned multicnt:2; ++ ++ /** Device address */ ++ unsigned devaddr:7; ++ ++ /** ++ * Frame to transmit periodic transaction. ++ * 0: even, 1: odd ++ */ ++ unsigned oddfrm:1; ++ ++ /** Channel disable */ ++ unsigned chdis:1; ++ ++ /** Channel enable */ ++ unsigned chen:1; ++ } b; ++} hcchar_data_t; ++ ++typedef union hcsplt_data { ++ /** raw register data */ ++ uint32_t d32; ++ ++ /** register bits */ ++ struct { ++ /** Port Address */ ++ unsigned prtaddr:7; ++ ++ /** Hub Address */ ++ unsigned hubaddr:7; ++ ++ /** Transaction Position */ ++ unsigned xactpos:2; ++#define DWC_HCSPLIT_XACTPOS_MID 0 ++#define DWC_HCSPLIT_XACTPOS_END 1 ++#define DWC_HCSPLIT_XACTPOS_BEGIN 2 ++#define DWC_HCSPLIT_XACTPOS_ALL 3 ++ ++ /** Do Complete Split */ ++ unsigned compsplt:1; ++ ++ /** Reserved */ ++ unsigned reserved:14; ++ ++ /** Split Enble */ ++ unsigned spltena:1; ++ } b; ++} hcsplt_data_t; ++ ++/** ++ * This union represents the bit fields in the Host All Interrupt ++ * Register. ++ */ ++typedef union hcint_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** Transfer Complete */ ++ unsigned xfercomp:1; ++ /** Channel Halted */ ++ unsigned chhltd:1; ++ /** AHB Error */ ++ unsigned ahberr:1; ++ /** STALL Response Received */ ++ unsigned stall:1; ++ /** NAK Response Received */ ++ unsigned nak:1; ++ /** ACK Response Received */ ++ unsigned ack:1; ++ /** NYET Response Received */ ++ unsigned nyet:1; ++ /** Transaction Err */ ++ unsigned xacterr:1; ++ /** Babble Error */ ++ unsigned bblerr:1; ++ /** Frame Overrun */ ++ unsigned frmovrun:1; ++ /** Data Toggle Error */ ++ unsigned datatglerr:1; ++ /** Buffer Not Available (only for DDMA mode) */ ++ unsigned bna:1; ++ /** Exessive transaction error (only for DDMA mode) */ ++ unsigned xcs_xact:1; ++ /** Frame List Rollover interrupt */ ++ unsigned frm_list_roll:1; ++ /** Reserved */ ++ unsigned reserved14_31:18; ++ } b; ++} hcint_data_t; ++ ++/** ++ * This union represents the bit fields in the Host Channel Interrupt Mask ++ * Register. Read the register into the d32 member then set/clear the ++ * bits using the bit elements. Write the d32 member to the ++ * hcintmsk register. ++ */ ++typedef union hcintmsk_data { ++ /** raw register data */ ++ uint32_t d32; ++ ++ /** register bits */ ++ struct { ++ unsigned xfercompl:1; ++ unsigned chhltd:1; ++ unsigned ahberr:1; ++ unsigned stall:1; ++ unsigned nak:1; ++ unsigned ack:1; ++ unsigned nyet:1; ++ unsigned xacterr:1; ++ unsigned bblerr:1; ++ unsigned frmovrun:1; ++ unsigned datatglerr:1; ++ unsigned bna:1; ++ unsigned xcs_xact:1; ++ unsigned frm_list_roll:1; ++ unsigned reserved14_31:18; ++ } b; ++} hcintmsk_data_t; ++ ++/** ++ * This union represents the bit fields in the Host Channel Transfer Size ++ * Register. Read the register into the d32 member then set/clear the ++ * bits using the bit elements. Write the d32 member to the ++ * hcchar register. ++ */ ++ ++typedef union hctsiz_data { ++ /** raw register data */ ++ uint32_t d32; ++ ++ /** register bits */ ++ struct { ++ /** Total transfer size in bytes */ ++ unsigned xfersize:19; ++ ++ /** Data packets to transfer */ ++ unsigned pktcnt:10; ++ ++ /** ++ * Packet ID for next data packet ++ * 0: DATA0 ++ * 1: DATA2 ++ * 2: DATA1 ++ * 3: MDATA (non-Control), SETUP (Control) ++ */ ++ unsigned pid:2; ++#define DWC_HCTSIZ_DATA0 0 ++#define DWC_HCTSIZ_DATA1 2 ++#define DWC_HCTSIZ_DATA2 1 ++#define DWC_HCTSIZ_MDATA 3 ++#define DWC_HCTSIZ_SETUP 3 ++ ++ /** Do PING protocol when 1 */ ++ unsigned dopng:1; ++ } b; ++ ++ /** register bits */ ++ struct { ++ /** Scheduling information */ ++ unsigned schinfo:8; ++ ++ /** Number of transfer descriptors. ++ * Max value: ++ * 64 in general, ++ * 256 only for HS isochronous endpoint. ++ */ ++ unsigned ntd:8; ++ ++ /** Data packets to transfer */ ++ unsigned reserved16_28:13; ++ ++ /** ++ * Packet ID for next data packet ++ * 0: DATA0 ++ * 1: DATA2 ++ * 2: DATA1 ++ * 3: MDATA (non-Control) ++ */ ++ unsigned pid:2; ++ ++ /** Do PING protocol when 1 */ ++ unsigned dopng:1; ++ } b_ddma; ++} hctsiz_data_t; ++ ++/** ++ * This union represents the bit fields in the Host DMA Address ++ * Register used in Descriptor DMA mode. ++ */ ++typedef union hcdma_data { ++ /** raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ unsigned reserved0_2:3; ++ /** Current Transfer Descriptor. Not used for ISOC */ ++ unsigned ctd:8; ++ /** Start Address of Descriptor List */ ++ unsigned dma_addr:21; ++ } b; ++} hcdma_data_t; ++ ++/** ++ * This union represents the bit fields in the DMA Descriptor ++ * status quadlet for host mode. Read the quadlet into the d32 member then ++ * set/clear the bits using the bit elements. ++ */ ++typedef union host_dma_desc_sts { ++ /** raw register data */ ++ uint32_t d32; ++ /** quadlet bits */ ++ ++ /* for non-isochronous */ ++ struct { ++ /** Number of bytes */ ++ unsigned n_bytes:17; ++ /** QTD offset to jump when Short Packet received - only for IN EPs */ ++ unsigned qtd_offset:6; ++ /** ++ * Set to request the core to jump to alternate QTD if ++ * Short Packet received - only for IN EPs ++ */ ++ unsigned a_qtd:1; ++ /** ++ * Setup Packet bit. When set indicates that buffer contains ++ * setup packet. ++ */ ++ unsigned sup:1; ++ /** Interrupt On Complete */ ++ unsigned ioc:1; ++ /** End of List */ ++ unsigned eol:1; ++ unsigned reserved27:1; ++ /** Rx/Tx Status */ ++ unsigned sts:2; ++#define DMA_DESC_STS_PKTERR 1 ++ unsigned reserved30:1; ++ /** Active Bit */ ++ unsigned a:1; ++ } b; ++ /* for isochronous */ ++ struct { ++ /** Number of bytes */ ++ unsigned n_bytes:12; ++ unsigned reserved12_24:13; ++ /** Interrupt On Complete */ ++ unsigned ioc:1; ++ unsigned reserved26_27:2; ++ /** Rx/Tx Status */ ++ unsigned sts:2; ++ unsigned reserved30:1; ++ /** Active Bit */ ++ unsigned a:1; ++ } b_isoc; ++} host_dma_desc_sts_t; ++ ++#define MAX_DMA_DESC_SIZE 131071 ++#define MAX_DMA_DESC_NUM_GENERIC 64 ++#define MAX_DMA_DESC_NUM_HS_ISOC 256 ++#define MAX_FRLIST_EN_NUM 64 ++/** ++ * Host-mode DMA Descriptor structure ++ * ++ * DMA Descriptor structure contains two quadlets: ++ * Status quadlet and Data buffer pointer. ++ */ ++typedef struct dwc_otg_host_dma_desc { ++ /** DMA Descriptor status quadlet */ ++ host_dma_desc_sts_t status; ++ /** DMA Descriptor data buffer pointer */ ++ uint32_t buf; ++} dwc_otg_host_dma_desc_t; ++ ++/** OTG Host Interface Structure. ++ * ++ * The OTG Host Interface Structure structure contains information ++ * needed to manage the DWC_otg controller acting in host mode. It ++ * represents the programming view of the host-specific aspects of the ++ * controller. ++ */ ++typedef struct dwc_otg_host_if { ++ /** Host Global Registers starting at offset 400h.*/ ++ dwc_otg_host_global_regs_t *host_global_regs; ++#define DWC_OTG_HOST_GLOBAL_REG_OFFSET 0x400 ++ ++ /** Host Port 0 Control and Status Register */ ++ volatile uint32_t *hprt0; ++#define DWC_OTG_HOST_PORT_REGS_OFFSET 0x440 ++ ++ /** Host Channel Specific Registers at offsets 500h-5FCh. */ ++ dwc_otg_hc_regs_t *hc_regs[MAX_EPS_CHANNELS]; ++#define DWC_OTG_HOST_CHAN_REGS_OFFSET 0x500 ++#define DWC_OTG_CHAN_REGS_OFFSET 0x20 ++ ++ /* Host configuration information */ ++ /** Number of Host Channels (range: 1-16) */ ++ uint8_t num_host_channels; ++ /** Periodic EPs supported (0: no, 1: yes) */ ++ uint8_t perio_eps_supported; ++ /** Periodic Tx FIFO Size (Only 1 host periodic Tx FIFO) */ ++ uint16_t perio_tx_fifo_size; ++ ++} dwc_otg_host_if_t; ++ ++/** ++ * This union represents the bit fields in the Power and Clock Gating Control ++ * Register. Read the register into the d32 member then set/clear the ++ * bits using the bit elements. ++ */ ++typedef union pcgcctl_data { ++ /** raw register data */ ++ uint32_t d32; ++ ++ /** register bits */ ++ struct { ++ /** Stop Pclk */ ++ unsigned stoppclk:1; ++ /** Gate Hclk */ ++ unsigned gatehclk:1; ++ /** Power Clamp */ ++ unsigned pwrclmp:1; ++ /** Reset Power Down Modules */ ++ unsigned rstpdwnmodule:1; ++ /** Reserved */ ++ unsigned reserved:1; ++ /** Enable Sleep Clock Gating (Enbl_L1Gating) */ ++ unsigned enbl_sleep_gating:1; ++ /** PHY In Sleep (PhySleep) */ ++ unsigned phy_in_sleep:1; ++ /** Deep Sleep*/ ++ unsigned deep_sleep:1; ++ unsigned resetaftsusp:1; ++ unsigned restoremode:1; ++ unsigned enbl_extnd_hiber:1; ++ unsigned extnd_hiber_pwrclmp:1; ++ unsigned extnd_hiber_switch:1; ++ unsigned ess_reg_restored:1; ++ unsigned prt_clk_sel:2; ++ unsigned port_power:1; ++ unsigned max_xcvrselect:2; ++ unsigned max_termsel:1; ++ unsigned mac_dev_addr:7; ++ unsigned p2hd_dev_enum_spd:2; ++ unsigned p2hd_prt_spd:2; ++ unsigned if_dev_mode:1; ++ } b; ++} pcgcctl_data_t; ++ ++/** ++ * This union represents the bit fields in the Global Data FIFO Software ++ * Configuration Register. Read the register into the d32 member then ++ * set/clear the bits using the bit elements. ++ */ ++typedef union gdfifocfg_data { ++ /* raw register data */ ++ uint32_t d32; ++ /** register bits */ ++ struct { ++ /** OTG Data FIFO depth */ ++ unsigned gdfifocfg:16; ++ /** Start address of EP info controller */ ++ unsigned epinfobase:16; ++ } b; ++} gdfifocfg_data_t; ++ ++/** ++ * This union represents the bit fields in the Global Power Down Register ++ * Register. Read the register into the d32 member then set/clear the ++ * bits using the bit elements. ++ */ ++typedef union gpwrdn_data { ++ /* raw register data */ ++ uint32_t d32; ++ ++ /** register bits */ ++ struct { ++ /** PMU Interrupt Select */ ++ unsigned pmuintsel:1; ++ /** PMU Active */ ++ unsigned pmuactv:1; ++ /** Restore */ ++ unsigned restore:1; ++ /** Power Down Clamp */ ++ unsigned pwrdnclmp:1; ++ /** Power Down Reset */ ++ unsigned pwrdnrstn:1; ++ /** Power Down Switch */ ++ unsigned pwrdnswtch:1; ++ /** Disable VBUS */ ++ unsigned dis_vbus:1; ++ /** Line State Change */ ++ unsigned lnstschng:1; ++ /** Line state change mask */ ++ unsigned lnstchng_msk:1; ++ /** Reset Detected */ ++ unsigned rst_det:1; ++ /** Reset Detect mask */ ++ unsigned rst_det_msk:1; ++ /** Disconnect Detected */ ++ unsigned disconn_det:1; ++ /** Disconnect Detect mask */ ++ unsigned disconn_det_msk:1; ++ /** Connect Detected*/ ++ unsigned connect_det:1; ++ /** Connect Detected Mask*/ ++ unsigned connect_det_msk:1; ++ /** SRP Detected */ ++ unsigned srp_det:1; ++ /** SRP Detect mask */ ++ unsigned srp_det_msk:1; ++ /** Status Change Interrupt */ ++ unsigned sts_chngint:1; ++ /** Status Change Interrupt Mask */ ++ unsigned sts_chngint_msk:1; ++ /** Line State */ ++ unsigned linestate:2; ++ /** Indicates current mode(status of IDDIG signal) */ ++ unsigned idsts:1; ++ /** B Session Valid signal status*/ ++ unsigned bsessvld:1; ++ /** ADP Event Detected */ ++ unsigned adp_int:1; ++ /** Multi Valued ID pin */ ++ unsigned mult_val_id_bc:5; ++ /** Reserved 24_31 */ ++ unsigned reserved29_31:3; ++ } b; ++} gpwrdn_data_t; ++ ++#endif +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/test/Makefile +@@ -0,0 +1,16 @@ ++ ++PERL=/usr/bin/perl ++PL_TESTS=test_sysfs.pl test_mod_param.pl ++ ++.PHONY : test ++test : perl_tests ++ ++perl_tests : ++ @echo ++ @echo Running perl tests ++ @for test in $(PL_TESTS); do \ ++ if $(PERL) ./$$test ; then \ ++ echo "=======> $$test, PASSED" ; \ ++ else echo "=======> $$test, FAILED" ; \ ++ fi \ ++ done +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/test/dwc_otg_test.pm +@@ -0,0 +1,337 @@ ++package dwc_otg_test; ++ ++use strict; ++use Exporter (); ++ ++use vars qw(@ISA @EXPORT ++$sysfsdir $paramdir $errors $params ++); ++ ++@ISA = qw(Exporter); ++ ++# ++# Globals ++# ++$sysfsdir = "/sys/devices/lm0"; ++$paramdir = "/sys/module/dwc_otg"; ++$errors = 0; ++ ++$params = [ ++ { ++ NAME => "otg_cap", ++ DEFAULT => 0, ++ ENUM => [], ++ LOW => 0, ++ HIGH => 2 ++ }, ++ { ++ NAME => "dma_enable", ++ DEFAULT => 0, ++ ENUM => [], ++ LOW => 0, ++ HIGH => 1 ++ }, ++ { ++ NAME => "dma_burst_size", ++ DEFAULT => 32, ++ ENUM => [1, 4, 8, 16, 32, 64, 128, 256], ++ LOW => 1, ++ HIGH => 256 ++ }, ++ { ++ NAME => "host_speed", ++ DEFAULT => 0, ++ ENUM => [], ++ LOW => 0, ++ HIGH => 1 ++ }, ++ { ++ NAME => "host_support_fs_ls_low_power", ++ DEFAULT => 0, ++ ENUM => [], ++ LOW => 0, ++ HIGH => 1 ++ }, ++ { ++ NAME => "host_ls_low_power_phy_clk", ++ DEFAULT => 0, ++ ENUM => [], ++ LOW => 0, ++ HIGH => 1 ++ }, ++ { ++ NAME => "dev_speed", ++ DEFAULT => 0, ++ ENUM => [], ++ LOW => 0, ++ HIGH => 1 ++ }, ++ { ++ NAME => "enable_dynamic_fifo", ++ DEFAULT => 1, ++ ENUM => [], ++ LOW => 0, ++ HIGH => 1 ++ }, ++ { ++ NAME => "data_fifo_size", ++ DEFAULT => 8192, ++ ENUM => [], ++ LOW => 32, ++ HIGH => 32768 ++ }, ++ { ++ NAME => "dev_rx_fifo_size", ++ DEFAULT => 1064, ++ ENUM => [], ++ LOW => 16, ++ HIGH => 32768 ++ }, ++ { ++ NAME => "dev_nperio_tx_fifo_size", ++ DEFAULT => 1024, ++ ENUM => [], ++ LOW => 16, ++ HIGH => 32768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_1", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_2", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_3", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_4", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_5", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_6", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_7", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_8", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_9", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_10", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_11", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_12", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_13", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_14", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "dev_perio_tx_fifo_size_15", ++ DEFAULT => 256, ++ ENUM => [], ++ LOW => 4, ++ HIGH => 768 ++ }, ++ { ++ NAME => "host_rx_fifo_size", ++ DEFAULT => 1024, ++ ENUM => [], ++ LOW => 16, ++ HIGH => 32768 ++ }, ++ { ++ NAME => "host_nperio_tx_fifo_size", ++ DEFAULT => 1024, ++ ENUM => [], ++ LOW => 16, ++ HIGH => 32768 ++ }, ++ { ++ NAME => "host_perio_tx_fifo_size", ++ DEFAULT => 1024, ++ ENUM => [], ++ LOW => 16, ++ HIGH => 32768 ++ }, ++ { ++ NAME => "max_transfer_size", ++ DEFAULT => 65535, ++ ENUM => [], ++ LOW => 2047, ++ HIGH => 65535 ++ }, ++ { ++ NAME => "max_packet_count", ++ DEFAULT => 511, ++ ENUM => [], ++ LOW => 15, ++ HIGH => 511 ++ }, ++ { ++ NAME => "host_channels", ++ DEFAULT => 12, ++ ENUM => [], ++ LOW => 1, ++ HIGH => 16 ++ }, ++ { ++ NAME => "dev_endpoints", ++ DEFAULT => 6, ++ ENUM => [], ++ LOW => 1, ++ HIGH => 15 ++ }, ++ { ++ NAME => "phy_type", ++ DEFAULT => 1, ++ ENUM => [], ++ LOW => 0, ++ HIGH => 2 ++ }, ++ { ++ NAME => "phy_utmi_width", ++ DEFAULT => 16, ++ ENUM => [8, 16], ++ LOW => 8, ++ HIGH => 16 ++ }, ++ { ++ NAME => "phy_ulpi_ddr", ++ DEFAULT => 0, ++ ENUM => [], ++ LOW => 0, ++ HIGH => 1 ++ }, ++ ]; ++ ++ ++# ++# ++sub check_arch { ++ $_ = `uname -m`; ++ chomp; ++ unless (m/armv4tl/) { ++ warn "# \n# Can't execute on $_. Run on integrator platform.\n# \n"; ++ return 0; ++ } ++ return 1; ++} ++ ++# ++# ++sub load_module { ++ my $params = shift; ++ print "\nRemoving Module\n"; ++ system "rmmod dwc_otg"; ++ print "Loading Module\n"; ++ if ($params ne "") { ++ print "Module Parameters: $params\n"; ++ } ++ if (system("modprobe dwc_otg $params")) { ++ warn "Unable to load module\n"; ++ return 0; ++ } ++ return 1; ++} ++ ++# ++# ++sub test_status { ++ my $arg = shift; ++ ++ print "\n"; ++ ++ if (defined $arg) { ++ warn "WARNING: $arg\n"; ++ } ++ ++ if ($errors > 0) { ++ warn "TEST FAILED with $errors errors\n"; ++ return 0; ++ } else { ++ print "TEST PASSED\n"; ++ return 0 if (defined $arg); ++ } ++ return 1; ++} ++ ++# ++# ++@EXPORT = qw( ++$sysfsdir ++$paramdir ++$params ++$errors ++check_arch ++load_module ++test_status ++); ++ ++1; +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/test/test_mod_param.pl +@@ -0,0 +1,133 @@ ++#!/usr/bin/perl -w ++# ++# Run this program on the integrator. ++# ++# - Tests module parameter default values. ++# - Tests setting of valid module parameter values via modprobe. ++# - Tests invalid module parameter values. ++# ----------------------------------------------------------------------------- ++use strict; ++use dwc_otg_test; ++ ++check_arch() or die; ++ ++# ++# ++sub test { ++ my ($param,$expected) = @_; ++ my $value = get($param); ++ ++ if ($value == $expected) { ++ print "$param = $value, okay\n"; ++ } ++ ++ else { ++ warn "ERROR: value of $param != $expected, $value\n"; ++ $errors ++; ++ } ++} ++ ++# ++# ++sub get { ++ my $param = shift; ++ my $tmp = `cat $paramdir/$param`; ++ chomp $tmp; ++ return $tmp; ++} ++ ++# ++# ++sub test_main { ++ ++ print "\nTesting Module Parameters\n"; ++ ++ load_module("") or die; ++ ++ # Test initial values ++ print "\nTesting Default Values\n"; ++ foreach (@{$params}) { ++ test ($_->{NAME}, $_->{DEFAULT}); ++ } ++ ++ # Test low value ++ print "\nTesting Low Value\n"; ++ my $cmd_params = ""; ++ foreach (@{$params}) { ++ $cmd_params = $cmd_params . "$_->{NAME}=$_->{LOW} "; ++ } ++ load_module($cmd_params) or die; ++ ++ foreach (@{$params}) { ++ test ($_->{NAME}, $_->{LOW}); ++ } ++ ++ # Test high value ++ print "\nTesting High Value\n"; ++ $cmd_params = ""; ++ foreach (@{$params}) { ++ $cmd_params = $cmd_params . "$_->{NAME}=$_->{HIGH} "; ++ } ++ load_module($cmd_params) or die; ++ ++ foreach (@{$params}) { ++ test ($_->{NAME}, $_->{HIGH}); ++ } ++ ++ # Test Enum ++ print "\nTesting Enumerated\n"; ++ foreach (@{$params}) { ++ if (defined $_->{ENUM}) { ++ my $value; ++ foreach $value (@{$_->{ENUM}}) { ++ $cmd_params = "$_->{NAME}=$value"; ++ load_module($cmd_params) or die; ++ test ($_->{NAME}, $value); ++ } ++ } ++ } ++ ++ # Test Invalid Values ++ print "\nTesting Invalid Values\n"; ++ $cmd_params = ""; ++ foreach (@{$params}) { ++ $cmd_params = $cmd_params . sprintf "$_->{NAME}=%d ", $_->{LOW}-1; ++ } ++ load_module($cmd_params) or die; ++ ++ foreach (@{$params}) { ++ test ($_->{NAME}, $_->{DEFAULT}); ++ } ++ ++ $cmd_params = ""; ++ foreach (@{$params}) { ++ $cmd_params = $cmd_params . sprintf "$_->{NAME}=%d ", $_->{HIGH}+1; ++ } ++ load_module($cmd_params) or die; ++ ++ foreach (@{$params}) { ++ test ($_->{NAME}, $_->{DEFAULT}); ++ } ++ ++ print "\nTesting Enumerated\n"; ++ foreach (@{$params}) { ++ if (defined $_->{ENUM}) { ++ my $value; ++ foreach $value (@{$_->{ENUM}}) { ++ $value = $value + 1; ++ $cmd_params = "$_->{NAME}=$value"; ++ load_module($cmd_params) or die; ++ test ($_->{NAME}, $_->{DEFAULT}); ++ $value = $value - 2; ++ $cmd_params = "$_->{NAME}=$value"; ++ load_module($cmd_params) or die; ++ test ($_->{NAME}, $_->{DEFAULT}); ++ } ++ } ++ } ++ ++ test_status() or die; ++} ++ ++test_main(); ++0; +--- /dev/null ++++ b/drivers/usb/host/dwc_otg/test/test_sysfs.pl +@@ -0,0 +1,193 @@ ++#!/usr/bin/perl -w ++# ++# Run this program on the integrator ++# - Tests select sysfs attributes. ++# - Todo ... test more attributes, hnp/srp, buspower/bussuspend, etc. ++# ----------------------------------------------------------------------------- ++use strict; ++use dwc_otg_test; ++ ++check_arch() or die; ++ ++# ++# ++sub test { ++ my ($attr,$expected) = @_; ++ my $string = get($attr); ++ ++ if ($string eq $expected) { ++ printf("$attr = $string, okay\n"); ++ } ++ else { ++ warn "ERROR: value of $attr != $expected, $string\n"; ++ $errors ++; ++ } ++} ++ ++# ++# ++sub set { ++ my ($reg, $value) = @_; ++ system "echo $value > $sysfsdir/$reg"; ++} ++ ++# ++# ++sub get { ++ my $attr = shift; ++ my $string = `cat $sysfsdir/$attr`; ++ chomp $string; ++ if ($string =~ m/\s\=\s/) { ++ my $tmp; ++ ($tmp, $string) = split /\s=\s/, $string; ++ } ++ return $string; ++} ++ ++# ++# ++sub test_main { ++ print("\nTesting Sysfs Attributes\n"); ++ ++ load_module("") or die; ++ ++ # Test initial values of regoffset/regvalue/guid/gsnpsid ++ print("\nTesting Default Values\n"); ++ ++ test("regoffset", "0xffffffff"); ++ test("regvalue", "invalid offset"); ++ test("guid", "0x12345678"); # this will fail if it has been changed ++ test("gsnpsid", "0x4f54200a"); ++ ++ # Test operation of regoffset/regvalue ++ print("\nTesting regoffset\n"); ++ set('regoffset', '5a5a5a5a'); ++ test("regoffset", "0xffffffff"); ++ ++ set('regoffset', '0'); ++ test("regoffset", "0x00000000"); ++ ++ set('regoffset', '40000'); ++ test("regoffset", "0x00000000"); ++ ++ set('regoffset', '3ffff'); ++ test("regoffset", "0x0003ffff"); ++ ++ set('regoffset', '1'); ++ test("regoffset", "0x00000001"); ++ ++ print("\nTesting regvalue\n"); ++ set('regoffset', '3c'); ++ test("regvalue", "0x12345678"); ++ set('regvalue', '5a5a5a5a'); ++ test("regvalue", "0x5a5a5a5a"); ++ set('regvalue','a5a5a5a5'); ++ test("regvalue", "0xa5a5a5a5"); ++ set('guid','12345678'); ++ ++ # Test HNP Capable ++ print("\nTesting HNP Capable bit\n"); ++ set('hnpcapable', '1'); ++ test("hnpcapable", "0x1"); ++ set('hnpcapable','0'); ++ test("hnpcapable", "0x0"); ++ ++ set('regoffset','0c'); ++ ++ my $old = get('gusbcfg'); ++ print("setting hnpcapable\n"); ++ set('hnpcapable', '1'); ++ test("hnpcapable", "0x1"); ++ test('gusbcfg', sprintf "0x%08x", (oct ($old) | (1<<9))); ++ test('regvalue', sprintf "0x%08x", (oct ($old) | (1<<9))); ++ ++ $old = get('gusbcfg'); ++ print("clearing hnpcapable\n"); ++ set('hnpcapable', '0'); ++ test("hnpcapable", "0x0"); ++ test ('gusbcfg', sprintf "0x%08x", oct ($old) & (~(1<<9))); ++ test ('regvalue', sprintf "0x%08x", oct ($old) & (~(1<<9))); ++ ++ # Test SRP Capable ++ print("\nTesting SRP Capable bit\n"); ++ set('srpcapable', '1'); ++ test("srpcapable", "0x1"); ++ set('srpcapable','0'); ++ test("srpcapable", "0x0"); ++ ++ set('regoffset','0c'); ++ ++ $old = get('gusbcfg'); ++ print("setting srpcapable\n"); ++ set('srpcapable', '1'); ++ test("srpcapable", "0x1"); ++ test('gusbcfg', sprintf "0x%08x", (oct ($old) | (1<<8))); ++ test('regvalue', sprintf "0x%08x", (oct ($old) | (1<<8))); ++ ++ $old = get('gusbcfg'); ++ print("clearing srpcapable\n"); ++ set('srpcapable', '0'); ++ test("srpcapable", "0x0"); ++ test('gusbcfg', sprintf "0x%08x", oct ($old) & (~(1<<8))); ++ test('regvalue', sprintf "0x%08x", oct ($old) & (~(1<<8))); ++ ++ # Test GGPIO ++ print("\nTesting GGPIO\n"); ++ set('ggpio','5a5a5a5a'); ++ test('ggpio','0x5a5a0000'); ++ set('ggpio','a5a5a5a5'); ++ test('ggpio','0xa5a50000'); ++ set('ggpio','11110000'); ++ test('ggpio','0x11110000'); ++ set('ggpio','00001111'); ++ test('ggpio','0x00000000'); ++ ++ # Test DEVSPEED ++ print("\nTesting DEVSPEED\n"); ++ set('regoffset','800'); ++ $old = get('regvalue'); ++ set('devspeed','0'); ++ test('devspeed','0x0'); ++ test('regvalue',sprintf("0x%08x", oct($old) & ~(0x3))); ++ set('devspeed','1'); ++ test('devspeed','0x1'); ++ test('regvalue',sprintf("0x%08x", oct($old) & ~(0x3) | 1)); ++ set('devspeed','2'); ++ test('devspeed','0x2'); ++ test('regvalue',sprintf("0x%08x", oct($old) & ~(0x3) | 2)); ++ set('devspeed','3'); ++ test('devspeed','0x3'); ++ test('regvalue',sprintf("0x%08x", oct($old) & ~(0x3) | 3)); ++ set('devspeed','4'); ++ test('devspeed','0x0'); ++ test('regvalue',sprintf("0x%08x", oct($old) & ~(0x3))); ++ set('devspeed','5'); ++ test('devspeed','0x1'); ++ test('regvalue',sprintf("0x%08x", oct($old) & ~(0x3) | 1)); ++ ++ ++ # mode Returns the current mode:0 for device mode1 for host mode Read ++ # hnp Initiate the Host Negotiation Protocol. Read returns the status. Read/Write ++ # srp Initiate the Session Request Protocol. Read returns the status. Read/Write ++ # buspower Get or Set the Power State of the bus (0 - Off or 1 - On) Read/Write ++ # bussuspend Suspend the USB bus. Read/Write ++ # busconnected Get the connection status of the bus Read ++ ++ # gotgctl Get or set the Core Control Status Register. Read/Write ++ ## gusbcfg Get or set the Core USB Configuration Register Read/Write ++ # grxfsiz Get or set the Receive FIFO Size Register Read/Write ++ # gnptxfsiz Get or set the non-periodic Transmit Size Register Read/Write ++ # gpvndctl Get or set the PHY Vendor Control Register Read/Write ++ ## ggpio Get the value in the lower 16-bits of the General Purpose IO Register or Set the upper 16 bits. Read/Write ++ ## guid Get or set the value of the User ID Register Read/Write ++ ## gsnpsid Get the value of the Synopsys ID Regester Read ++ ## devspeed Get or set the device speed setting in the DCFG register Read/Write ++ # enumspeed Gets the device enumeration Speed. Read ++ # hptxfsiz Get the value of the Host Periodic Transmit FIFO Read ++ # hprt0 Get or Set the value in the Host Port Control and Status Register Read/Write ++ ++ test_status("TEST NYI") or die; ++} ++ ++test_main(); ++0; diff --git a/target/linux/bcm27xx/patches-5.10/950-0041-bcm2708-framebuffer-driver.patch b/target/linux/bcm27xx/patches-5.10/950-0041-bcm2708-framebuffer-driver.patch new file mode 100644 index 0000000000..d14de59384 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0041-bcm2708-framebuffer-driver.patch @@ -0,0 +1,3559 @@ +From 96f18d88062c3fe5754ab031fb5bde7686f6a510 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Wed, 17 Jun 2015 17:06:34 +0100 +Subject: [PATCH] bcm2708 framebuffer driver +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: popcornmix + +bcm2708_fb : Implement blanking support using the mailbox property interface + +bcm2708_fb: Add pan and vsync controls + +bcm2708_fb: DMA acceleration for fb_copyarea + +Based on http://www.raspberrypi.org/phpBB3/viewtopic.php?p=62425#p62425 +Also used Simon's dmaer_master module as a reference for tweaking DMA +settings for better performance. + +For now busylooping only. IRQ support might be added later. +With non-overclocked Raspberry Pi, the performance is ~360 MB/s +for simple copy or ~260 MB/s for two-pass copy (used when dragging +windows to the right). + +In the case of using DMA channel 0, the performance improves +to ~440 MB/s. + +For comparison, VFP optimized CPU copy can only do ~114 MB/s in +the same conditions (hindered by reading uncached source buffer). + +Signed-off-by: Siarhei Siamashka + +bcm2708_fb: report number of dma copies + +Add a counter (exported via debugfs) reporting the +number of dma copies that the framebuffer driver +has done, in order to help evaluate different +optimization strategies. + +Signed-off-by: Luke Diamand + +bcm2708_fb: use IRQ for DMA copies + +The copyarea ioctl() uses DMA to speed things along. This +was busy-waiting for completion. This change supports using +an interrupt instead for larger transfers. For small +transfers, busy-waiting is still likely to be faster. + +Signed-off-by: Luke Diamand + +bcm2708: Make ioctl logging quieter + +video: fbdev: bcm2708_fb: Don't panic on error + +No need to panic the kernel if the video driver fails. +Just print a message and return an error. + +Signed-off-by: Noralf Trønnes + +fbdev: bcm2708_fb: Add ARCH_BCM2835 support + +Add Device Tree support. +Pass the device to dma_alloc_coherent() in order to get the +correct bus address on ARCH_BCM2835. +Use the new DMA legacy API header file. +Including is not necessary. + +Signed-off-by: Noralf Trønnes + +BCM270x_DT: Add bcm2708-fb device + +Add bcm2708-fb to Device Tree and don't add the +platform device when booting in DT mode. + +Signed-off-by: Noralf Trønnes + +Cleanup of bcm2708_fb file to kernel coding standards + +Some minor change to function - remove a use of +in_atomic, plus replacing various debug messages +that manually specify the function name with +("%s",.__func__) + +Signed-off-by: James Hughes + +video: bcm2708_fb: Try allocating on the ARM and passing to VPU + +Currently the VPU allocates the contiguous buffer for the +framebuffer. +Try an alternate path first where we use dma_alloc_coherent +and pass the buffer to the VPU. Should the VPU firmware not +support that path, then free the buffer and revert to the +old behaviour of using the VPU allocation. + +Signed-off-by: Dave Stevenson +--- + drivers/video/fbdev/Kconfig | 14 + + drivers/video/fbdev/Makefile | 1 + + drivers/video/fbdev/bcm2708_fb.c | 920 ++++++++ + drivers/video/logo/logo_linux_clut224.ppm | 2483 +++++++------------- + include/soc/bcm2835/raspberrypi-firmware.h | 1 + + 5 files changed, 1817 insertions(+), 1602 deletions(-) + create mode 100644 drivers/video/fbdev/bcm2708_fb.c + +--- a/drivers/video/fbdev/Kconfig ++++ b/drivers/video/fbdev/Kconfig +@@ -219,6 +219,20 @@ config FB_TILEBLITTING + comment "Frame buffer hardware drivers" + depends on FB + ++config FB_BCM2708 ++ tristate "BCM2708 framebuffer support" ++ depends on FB && RASPBERRYPI_FIRMWARE ++ select FB_CFB_FILLRECT ++ select FB_CFB_COPYAREA ++ select FB_CFB_IMAGEBLIT ++ help ++ This framebuffer device driver is for the BCM2708 framebuffer. ++ ++ If you want to compile this as a module (=code which can be ++ inserted into and removed from the running kernel), say M ++ here and read . The module ++ will be called bcm2708_fb. ++ + config FB_GRVGA + tristate "Aeroflex Gaisler framebuffer support" + depends on FB && SPARC +--- a/drivers/video/fbdev/Makefile ++++ b/drivers/video/fbdev/Makefile +@@ -11,6 +11,7 @@ obj-$(CONFIG_FB_MACMODES) += macmod + obj-$(CONFIG_FB_WMT_GE_ROPS) += wmt_ge_rops.o + + # Hardware specific drivers go first ++obj-$(CONFIG_FB_BCM2708) += bcm2708_fb.o + obj-$(CONFIG_FB_AMIGA) += amifb.o c2p_planar.o + obj-$(CONFIG_FB_ARC) += arcfb.o + obj-$(CONFIG_FB_CLPS711X) += clps711x-fb.o +--- /dev/null ++++ b/drivers/video/fbdev/bcm2708_fb.c +@@ -0,0 +1,920 @@ ++/* ++ * linux/drivers/video/bcm2708_fb.c ++ * ++ * Copyright (C) 2010 Broadcom ++ * ++ * This file is subject to the terms and conditions of the GNU General Public ++ * License. See the file COPYING in the main directory of this archive ++ * for more details. ++ * ++ * Broadcom simple framebuffer driver ++ * ++ * This file is derived from cirrusfb.c ++ * Copyright 1999-2001 Jeff Garzik ++ * ++ */ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++//#define BCM2708_FB_DEBUG ++#define MODULE_NAME "bcm2708_fb" ++ ++#ifdef BCM2708_FB_DEBUG ++#define print_debug(fmt, ...) pr_debug("%s:%s:%d: " fmt, \ ++ MODULE_NAME, __func__, __LINE__, ##__VA_ARGS__) ++#else ++#define print_debug(fmt, ...) ++#endif ++ ++/* This is limited to 16 characters when displayed by X startup */ ++static const char *bcm2708_name = "BCM2708 FB"; ++ ++#define DRIVER_NAME "bcm2708_fb" ++ ++static int fbwidth = 800; /* module parameter */ ++static int fbheight = 480; /* module parameter */ ++static int fbdepth = 32; /* module parameter */ ++static int fbswap; /* module parameter */ ++ ++static u32 dma_busy_wait_threshold = 1 << 15; ++module_param(dma_busy_wait_threshold, int, 0644); ++MODULE_PARM_DESC(dma_busy_wait_threshold, "Busy-wait for DMA completion below this area"); ++ ++struct fb_alloc_tags { ++ struct rpi_firmware_property_tag_header tag1; ++ u32 xres, yres; ++ struct rpi_firmware_property_tag_header tag2; ++ u32 xres_virtual, yres_virtual; ++ struct rpi_firmware_property_tag_header tag3; ++ u32 bpp; ++ struct rpi_firmware_property_tag_header tag4; ++ u32 xoffset, yoffset; ++ struct rpi_firmware_property_tag_header tag5; ++ u32 base, screen_size; ++ struct rpi_firmware_property_tag_header tag6; ++ u32 pitch; ++}; ++ ++struct bcm2708_fb_stats { ++ struct debugfs_regset32 regset; ++ u32 dma_copies; ++ u32 dma_irqs; ++}; ++ ++struct bcm2708_fb { ++ struct fb_info fb; ++ struct platform_device *dev; ++ struct rpi_firmware *fw; ++ u32 cmap[16]; ++ u32 gpu_cmap[256]; ++ int dma_chan; ++ int dma_irq; ++ void __iomem *dma_chan_base; ++ void *cb_base; /* DMA control blocks */ ++ dma_addr_t cb_handle; ++ struct dentry *debugfs_dir; ++ wait_queue_head_t dma_waitq; ++ struct bcm2708_fb_stats stats; ++ unsigned long fb_bus_address; ++ bool disable_arm_alloc; ++ unsigned int image_size; ++ dma_addr_t dma_addr; ++ void *cpuaddr; ++}; ++ ++#define to_bcm2708(info) container_of(info, struct bcm2708_fb, fb) ++ ++static void bcm2708_fb_debugfs_deinit(struct bcm2708_fb *fb) ++{ ++ debugfs_remove_recursive(fb->debugfs_dir); ++ fb->debugfs_dir = NULL; ++} ++ ++static int bcm2708_fb_debugfs_init(struct bcm2708_fb *fb) ++{ ++ static struct debugfs_reg32 stats_registers[] = { ++ { ++ "dma_copies", ++ offsetof(struct bcm2708_fb_stats, dma_copies) ++ }, ++ { ++ "dma_irqs", ++ offsetof(struct bcm2708_fb_stats, dma_irqs) ++ }, ++ }; ++ ++ fb->debugfs_dir = debugfs_create_dir(DRIVER_NAME, NULL); ++ if (!fb->debugfs_dir) { ++ pr_warn("%s: could not create debugfs entry\n", ++ __func__); ++ return -EFAULT; ++ } ++ ++ fb->stats.regset.regs = stats_registers; ++ fb->stats.regset.nregs = ARRAY_SIZE(stats_registers); ++ fb->stats.regset.base = &fb->stats; ++ ++ debugfs_create_regset32("stats", 0444, fb->debugfs_dir, ++ &fb->stats.regset); ++ return 0; ++} ++ ++static int bcm2708_fb_set_bitfields(struct fb_var_screeninfo *var) ++{ ++ int ret = 0; ++ ++ memset(&var->transp, 0, sizeof(var->transp)); ++ ++ var->red.msb_right = 0; ++ var->green.msb_right = 0; ++ var->blue.msb_right = 0; ++ ++ switch (var->bits_per_pixel) { ++ case 1: ++ case 2: ++ case 4: ++ case 8: ++ var->red.length = var->bits_per_pixel; ++ var->red.offset = 0; ++ var->green.length = var->bits_per_pixel; ++ var->green.offset = 0; ++ var->blue.length = var->bits_per_pixel; ++ var->blue.offset = 0; ++ break; ++ case 16: ++ var->red.length = 5; ++ var->blue.length = 5; ++ /* ++ * Green length can be 5 or 6 depending whether ++ * we're operating in RGB555 or RGB565 mode. ++ */ ++ if (var->green.length != 5 && var->green.length != 6) ++ var->green.length = 6; ++ break; ++ case 24: ++ var->red.length = 8; ++ var->blue.length = 8; ++ var->green.length = 8; ++ break; ++ case 32: ++ var->red.length = 8; ++ var->green.length = 8; ++ var->blue.length = 8; ++ var->transp.length = 8; ++ break; ++ default: ++ ret = -EINVAL; ++ break; ++ } ++ ++ /* ++ * >= 16bpp displays have separate colour component bitfields ++ * encoded in the pixel data. Calculate their position from ++ * the bitfield length defined above. ++ */ ++ if (ret == 0 && var->bits_per_pixel >= 24 && fbswap) { ++ var->blue.offset = 0; ++ var->green.offset = var->blue.offset + var->blue.length; ++ var->red.offset = var->green.offset + var->green.length; ++ var->transp.offset = var->red.offset + var->red.length; ++ } else if (ret == 0 && var->bits_per_pixel >= 24) { ++ var->red.offset = 0; ++ var->green.offset = var->red.offset + var->red.length; ++ var->blue.offset = var->green.offset + var->green.length; ++ var->transp.offset = var->blue.offset + var->blue.length; ++ } else if (ret == 0 && var->bits_per_pixel >= 16) { ++ var->blue.offset = 0; ++ var->green.offset = var->blue.offset + var->blue.length; ++ var->red.offset = var->green.offset + var->green.length; ++ var->transp.offset = var->red.offset + var->red.length; ++ } ++ ++ return ret; ++} ++ ++static int bcm2708_fb_check_var(struct fb_var_screeninfo *var, ++ struct fb_info *info) ++{ ++ /* info input, var output */ ++ print_debug("%s(%p) %dx%d (%dx%d), %d, %d\n", ++ __func__, info, info->var.xres, info->var.yres, ++ info->var.xres_virtual, info->var.yres_virtual, ++ (int)info->screen_size, info->var.bits_per_pixel); ++ print_debug("%s(%p) %dx%d (%dx%d), %d\n", __func__, var, var->xres, ++ var->yres, var->xres_virtual, var->yres_virtual, ++ var->bits_per_pixel); ++ ++ if (!var->bits_per_pixel) ++ var->bits_per_pixel = 16; ++ ++ if (bcm2708_fb_set_bitfields(var) != 0) { ++ pr_err("%s: invalid bits_per_pixel %d\n", __func__, ++ var->bits_per_pixel); ++ return -EINVAL; ++ } ++ ++ if (var->xres_virtual < var->xres) ++ var->xres_virtual = var->xres; ++ /* use highest possible virtual resolution */ ++ if (var->yres_virtual == -1) { ++ var->yres_virtual = 480; ++ ++ pr_err("%s: virtual resolution set to maximum of %dx%d\n", ++ __func__, var->xres_virtual, var->yres_virtual); ++ } ++ if (var->yres_virtual < var->yres) ++ var->yres_virtual = var->yres; ++ ++ if (var->xoffset < 0) ++ var->xoffset = 0; ++ if (var->yoffset < 0) ++ var->yoffset = 0; ++ ++ /* truncate xoffset and yoffset to maximum if too high */ ++ if (var->xoffset > var->xres_virtual - var->xres) ++ var->xoffset = var->xres_virtual - var->xres - 1; ++ if (var->yoffset > var->yres_virtual - var->yres) ++ var->yoffset = var->yres_virtual - var->yres - 1; ++ ++ return 0; ++} ++ ++static int bcm2708_fb_set_par(struct fb_info *info) ++{ ++ struct bcm2708_fb *fb = to_bcm2708(info); ++ struct fb_alloc_tags fbinfo = { ++ .tag1 = { RPI_FIRMWARE_FRAMEBUFFER_SET_PHYSICAL_WIDTH_HEIGHT, ++ 8, 0, }, ++ .xres = info->var.xres, ++ .yres = info->var.yres, ++ .tag2 = { RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_WIDTH_HEIGHT, ++ 8, 0, }, ++ .xres_virtual = info->var.xres_virtual, ++ .yres_virtual = info->var.yres_virtual, ++ .tag3 = { RPI_FIRMWARE_FRAMEBUFFER_SET_DEPTH, 4, 0 }, ++ .bpp = info->var.bits_per_pixel, ++ .tag4 = { RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_OFFSET, 8, 0 }, ++ .xoffset = info->var.xoffset, ++ .yoffset = info->var.yoffset, ++ .tag5 = { RPI_FIRMWARE_FRAMEBUFFER_ALLOCATE, 8, 0 }, ++ /* base and screen_size will be initialised later */ ++ .tag6 = { RPI_FIRMWARE_FRAMEBUFFER_SET_PITCH, 4, 0 }, ++ /* pitch will be initialised later */ ++ }; ++ int ret, image_size; ++ ++ ++ print_debug("%s(%p) %dx%d (%dx%d), %d, %d\n", __func__, info, ++ info->var.xres, info->var.yres, info->var.xres_virtual, ++ info->var.yres_virtual, (int)info->screen_size, ++ info->var.bits_per_pixel); ++ ++ /* Try allocating our own buffer. We can specify all the parameters */ ++ image_size = ((info->var.xres * info->var.yres) * ++ info->var.bits_per_pixel) >> 3; ++ ++ if (!fb->disable_arm_alloc && ++ (image_size != fb->image_size || !fb->dma_addr)) { ++ if (fb->dma_addr) { ++ dma_free_coherent(info->device, fb->image_size, ++ fb->cpuaddr, fb->dma_addr); ++ fb->image_size = 0; ++ fb->cpuaddr = NULL; ++ fb->dma_addr = 0; ++ } ++ ++ fb->cpuaddr = dma_alloc_coherent(info->device, image_size, ++ &fb->dma_addr, GFP_KERNEL); ++ ++ if (!fb->cpuaddr) { ++ fb->dma_addr = 0; ++ fb->disable_arm_alloc = true; ++ } else { ++ fb->image_size = image_size; ++ } ++ } ++ ++ if (fb->cpuaddr) { ++ fbinfo.base = fb->dma_addr; ++ fbinfo.screen_size = image_size; ++ fbinfo.pitch = (info->var.xres * info->var.bits_per_pixel) >> 3; ++ ++ ret = rpi_firmware_property_list(fb->fw, &fbinfo, ++ sizeof(fbinfo)); ++ if (ret || fbinfo.base != fb->dma_addr) { ++ /* Firmware either failed, or assigned a different base ++ * address (ie it doesn't support being passed an FB ++ * allocation). ++ * Destroy the allocation, and don't try again. ++ */ ++ dma_free_coherent(info->device, fb->image_size, ++ fb->cpuaddr, fb->dma_addr); ++ fb->image_size = 0; ++ fb->cpuaddr = NULL; ++ fb->dma_addr = 0; ++ fb->disable_arm_alloc = true; ++ } ++ } else { ++ /* Our allocation failed - drop into the old scheme of ++ * allocation by the VPU. ++ */ ++ ret = -ENOMEM; ++ } ++ ++ if (ret) { ++ /* Old scheme: ++ * - FRAMEBUFFER_ALLOCATE passes 0 for base and screen_size. ++ * - GET_PITCH instead of SET_PITCH. ++ */ ++ fbinfo.base = 0; ++ fbinfo.screen_size = 0; ++ fbinfo.tag6.tag = RPI_FIRMWARE_FRAMEBUFFER_GET_PITCH; ++ fbinfo.pitch = 0; ++ ++ ret = rpi_firmware_property_list(fb->fw, &fbinfo, ++ sizeof(fbinfo)); ++ if (ret) { ++ dev_err(info->device, ++ "Failed to allocate GPU framebuffer (%d)\n", ++ ret); ++ return ret; ++ } ++ } ++ ++ if (info->var.bits_per_pixel <= 8) ++ fb->fb.fix.visual = FB_VISUAL_PSEUDOCOLOR; ++ else ++ fb->fb.fix.visual = FB_VISUAL_TRUECOLOR; ++ ++ fb->fb.fix.line_length = fbinfo.pitch; ++ fbinfo.base |= 0x40000000; ++ fb->fb_bus_address = fbinfo.base; ++ fbinfo.base &= ~0xc0000000; ++ fb->fb.fix.smem_start = fbinfo.base; ++ fb->fb.fix.smem_len = fbinfo.pitch * fbinfo.yres_virtual; ++ fb->fb.screen_size = fbinfo.screen_size; ++ ++ if (!fb->dma_addr) { ++ if (fb->fb.screen_base) ++ iounmap(fb->fb.screen_base); ++ ++ fb->fb.screen_base = ioremap_wc(fbinfo.base, ++ fb->fb.screen_size); ++ } else { ++ fb->fb.screen_base = fb->cpuaddr; ++ } ++ ++ if (!fb->fb.screen_base) { ++ /* the console may currently be locked */ ++ console_trylock(); ++ console_unlock(); ++ dev_err(info->device, "Failed to set screen_base\n"); ++ return -ENOMEM; ++ } ++ ++ print_debug("%s: start = %p,%p width=%d, height=%d, bpp=%d, pitch=%d size=%d\n", ++ __func__, (void *)fb->fb.screen_base, ++ (void *)fb->fb_bus_address, fbinfo.xres, fbinfo.yres, ++ fbinfo.bpp, fbinfo.pitch, (int)fb->fb.screen_size); ++ ++ return 0; ++} ++ ++static inline u32 convert_bitfield(int val, struct fb_bitfield *bf) ++{ ++ unsigned int mask = (1 << bf->length) - 1; ++ ++ return (val >> (16 - bf->length) & mask) << bf->offset; ++} ++ ++static int bcm2708_fb_setcolreg(unsigned int regno, unsigned int red, ++ unsigned int green, unsigned int blue, ++ unsigned int transp, struct fb_info *info) ++{ ++ struct bcm2708_fb *fb = to_bcm2708(info); ++ ++ if (fb->fb.var.bits_per_pixel <= 8) { ++ if (regno < 256) { ++ /* blue [23:16], green [15:8], red [7:0] */ ++ fb->gpu_cmap[regno] = ((red >> 8) & 0xff) << 0 | ++ ((green >> 8) & 0xff) << 8 | ++ ((blue >> 8) & 0xff) << 16; ++ } ++ /* Hack: we need to tell GPU the palette has changed, but ++ * currently bcm2708_fb_set_par takes noticeable time when ++ * called for every (256) colour ++ * So just call it for what looks like the last colour in a ++ * list for now. ++ */ ++ if (regno == 15 || regno == 255) { ++ struct packet { ++ u32 offset; ++ u32 length; ++ u32 cmap[256]; ++ } *packet; ++ int ret; ++ ++ packet = kmalloc(sizeof(*packet), GFP_KERNEL); ++ if (!packet) ++ return -ENOMEM; ++ packet->offset = 0; ++ packet->length = regno + 1; ++ memcpy(packet->cmap, fb->gpu_cmap, ++ sizeof(packet->cmap)); ++ ret = rpi_firmware_property(fb->fw, ++ RPI_FIRMWARE_FRAMEBUFFER_SET_PALETTE, ++ packet, ++ (2 + packet->length) * sizeof(u32)); ++ if (ret || packet->offset) ++ dev_err(info->device, ++ "Failed to set palette (%d,%u)\n", ++ ret, packet->offset); ++ kfree(packet); ++ } ++ } else if (regno < 16) { ++ fb->cmap[regno] = convert_bitfield(transp, &fb->fb.var.transp) | ++ convert_bitfield(blue, &fb->fb.var.blue) | ++ convert_bitfield(green, &fb->fb.var.green) | ++ convert_bitfield(red, &fb->fb.var.red); ++ } ++ return regno > 255; ++} ++ ++static int bcm2708_fb_blank(int blank_mode, struct fb_info *info) ++{ ++ struct bcm2708_fb *fb = to_bcm2708(info); ++ u32 value; ++ int ret; ++ ++ switch (blank_mode) { ++ case FB_BLANK_UNBLANK: ++ value = 0; ++ break; ++ case FB_BLANK_NORMAL: ++ case FB_BLANK_VSYNC_SUSPEND: ++ case FB_BLANK_HSYNC_SUSPEND: ++ case FB_BLANK_POWERDOWN: ++ value = 1; ++ break; ++ default: ++ return -EINVAL; ++ } ++ ++ ret = rpi_firmware_property(fb->fw, RPI_FIRMWARE_FRAMEBUFFER_BLANK, ++ &value, sizeof(value)); ++ if (ret) ++ dev_err(info->device, "%s(%d) failed: %d\n", __func__, ++ blank_mode, ret); ++ ++ return ret; ++} ++ ++static int bcm2708_fb_pan_display(struct fb_var_screeninfo *var, ++ struct fb_info *info) ++{ ++ s32 result; ++ ++ info->var.xoffset = var->xoffset; ++ info->var.yoffset = var->yoffset; ++ result = bcm2708_fb_set_par(info); ++ if (result != 0) ++ pr_err("%s(%d,%d) returns=%d\n", __func__, var->xoffset, ++ var->yoffset, result); ++ return result; ++} ++ ++static int bcm2708_ioctl(struct fb_info *info, unsigned int cmd, unsigned long arg) ++{ ++ struct bcm2708_fb *fb = to_bcm2708(info); ++ u32 dummy = 0; ++ int ret; ++ ++ switch (cmd) { ++ case FBIO_WAITFORVSYNC: ++ ret = rpi_firmware_property(fb->fw, ++ RPI_FIRMWARE_FRAMEBUFFER_SET_VSYNC, ++ &dummy, sizeof(dummy)); ++ break; ++ default: ++ dev_dbg(info->device, "Unknown ioctl 0x%x\n", cmd); ++ return -ENOTTY; ++ } ++ ++ if (ret) ++ dev_err(info->device, "ioctl 0x%x failed (%d)\n", cmd, ret); ++ ++ return ret; ++} ++static void bcm2708_fb_fillrect(struct fb_info *info, ++ const struct fb_fillrect *rect) ++{ ++ /* (is called) print_debug("bcm2708_fb_fillrect\n"); */ ++ cfb_fillrect(info, rect); ++} ++ ++/* A helper function for configuring dma control block */ ++static void set_dma_cb(struct bcm2708_dma_cb *cb, ++ int burst_size, ++ dma_addr_t dst, ++ int dst_stride, ++ dma_addr_t src, ++ int src_stride, ++ int w, ++ int h) ++{ ++ cb->info = BCM2708_DMA_BURST(burst_size) | BCM2708_DMA_S_WIDTH | ++ BCM2708_DMA_S_INC | BCM2708_DMA_D_WIDTH | ++ BCM2708_DMA_D_INC | BCM2708_DMA_TDMODE; ++ cb->dst = dst; ++ cb->src = src; ++ /* ++ * This is not really obvious from the DMA documentation, ++ * but the top 16 bits must be programmmed to "height -1" ++ * and not "height" in 2D mode. ++ */ ++ cb->length = ((h - 1) << 16) | w; ++ cb->stride = ((dst_stride - w) << 16) | (u16)(src_stride - w); ++ cb->pad[0] = 0; ++ cb->pad[1] = 0; ++} ++ ++static void bcm2708_fb_copyarea(struct fb_info *info, ++ const struct fb_copyarea *region) ++{ ++ struct bcm2708_fb *fb = to_bcm2708(info); ++ struct bcm2708_dma_cb *cb = fb->cb_base; ++ int bytes_per_pixel = (info->var.bits_per_pixel + 7) >> 3; ++ ++ /* Channel 0 supports larger bursts and is a bit faster */ ++ int burst_size = (fb->dma_chan == 0) ? 8 : 2; ++ int pixels = region->width * region->height; ++ ++ /* Fallback to cfb_copyarea() if we don't like something */ ++ if (bytes_per_pixel > 4 || ++ info->var.xres * info->var.yres > 1920 * 1200 || ++ region->width <= 0 || region->width > info->var.xres || ++ region->height <= 0 || region->height > info->var.yres || ++ region->sx < 0 || region->sx >= info->var.xres || ++ region->sy < 0 || region->sy >= info->var.yres || ++ region->dx < 0 || region->dx >= info->var.xres || ++ region->dy < 0 || region->dy >= info->var.yres || ++ region->sx + region->width > info->var.xres || ++ region->dx + region->width > info->var.xres || ++ region->sy + region->height > info->var.yres || ++ region->dy + region->height > info->var.yres) { ++ cfb_copyarea(info, region); ++ return; ++ } ++ ++ if (region->dy == region->sy && region->dx > region->sx) { ++ /* ++ * A difficult case of overlapped copy. Because DMA can't ++ * copy individual scanlines in backwards direction, we need ++ * two-pass processing. We do it by programming a chain of dma ++ * control blocks in the first 16K part of the buffer and use ++ * the remaining 48K as the intermediate temporary scratch ++ * buffer. The buffer size is sufficient to handle up to ++ * 1920x1200 resolution at 32bpp pixel depth. ++ */ ++ int y; ++ dma_addr_t control_block_pa = fb->cb_handle; ++ dma_addr_t scratchbuf = fb->cb_handle + 16 * 1024; ++ int scanline_size = bytes_per_pixel * region->width; ++ int scanlines_per_cb = (64 * 1024 - 16 * 1024) / scanline_size; ++ ++ for (y = 0; y < region->height; y += scanlines_per_cb) { ++ dma_addr_t src = ++ fb->fb_bus_address + ++ bytes_per_pixel * region->sx + ++ (region->sy + y) * fb->fb.fix.line_length; ++ dma_addr_t dst = ++ fb->fb_bus_address + ++ bytes_per_pixel * region->dx + ++ (region->dy + y) * fb->fb.fix.line_length; ++ ++ if (region->height - y < scanlines_per_cb) ++ scanlines_per_cb = region->height - y; ++ ++ set_dma_cb(cb, burst_size, scratchbuf, scanline_size, ++ src, fb->fb.fix.line_length, ++ scanline_size, scanlines_per_cb); ++ control_block_pa += sizeof(struct bcm2708_dma_cb); ++ cb->next = control_block_pa; ++ cb++; ++ ++ set_dma_cb(cb, burst_size, dst, fb->fb.fix.line_length, ++ scratchbuf, scanline_size, ++ scanline_size, scanlines_per_cb); ++ control_block_pa += sizeof(struct bcm2708_dma_cb); ++ cb->next = control_block_pa; ++ cb++; ++ } ++ /* move the pointer back to the last dma control block */ ++ cb--; ++ } else { ++ /* A single dma control block is enough. */ ++ int sy, dy, stride; ++ ++ if (region->dy <= region->sy) { ++ /* processing from top to bottom */ ++ dy = region->dy; ++ sy = region->sy; ++ stride = fb->fb.fix.line_length; ++ } else { ++ /* processing from bottom to top */ ++ dy = region->dy + region->height - 1; ++ sy = region->sy + region->height - 1; ++ stride = -fb->fb.fix.line_length; ++ } ++ set_dma_cb(cb, burst_size, ++ fb->fb_bus_address + dy * fb->fb.fix.line_length + ++ bytes_per_pixel * region->dx, ++ stride, ++ fb->fb_bus_address + sy * fb->fb.fix.line_length + ++ bytes_per_pixel * region->sx, ++ stride, ++ region->width * bytes_per_pixel, ++ region->height); ++ } ++ ++ /* end of dma control blocks chain */ ++ cb->next = 0; ++ ++ if (pixels < dma_busy_wait_threshold) { ++ bcm_dma_start(fb->dma_chan_base, fb->cb_handle); ++ bcm_dma_wait_idle(fb->dma_chan_base); ++ } else { ++ void __iomem *dma_chan = fb->dma_chan_base; ++ ++ cb->info |= BCM2708_DMA_INT_EN; ++ bcm_dma_start(fb->dma_chan_base, fb->cb_handle); ++ while (bcm_dma_is_busy(dma_chan)) { ++ wait_event_interruptible(fb->dma_waitq, ++ !bcm_dma_is_busy(dma_chan)); ++ } ++ fb->stats.dma_irqs++; ++ } ++ fb->stats.dma_copies++; ++} ++ ++static void bcm2708_fb_imageblit(struct fb_info *info, ++ const struct fb_image *image) ++{ ++ /* (is called) print_debug("bcm2708_fb_imageblit\n"); */ ++ cfb_imageblit(info, image); ++} ++ ++static irqreturn_t bcm2708_fb_dma_irq(int irq, void *cxt) ++{ ++ struct bcm2708_fb *fb = cxt; ++ ++ /* FIXME: should read status register to check if this is ++ * actually interrupting us or not, in case this interrupt ++ * ever becomes shared amongst several DMA channels ++ * ++ * readl(dma_chan_base + BCM2708_DMA_CS) & BCM2708_DMA_IRQ; ++ */ ++ ++ /* acknowledge the interrupt */ ++ writel(BCM2708_DMA_INT, fb->dma_chan_base + BCM2708_DMA_CS); ++ ++ wake_up(&fb->dma_waitq); ++ return IRQ_HANDLED; ++} ++ ++static struct fb_ops bcm2708_fb_ops = { ++ .owner = THIS_MODULE, ++ .fb_check_var = bcm2708_fb_check_var, ++ .fb_set_par = bcm2708_fb_set_par, ++ .fb_setcolreg = bcm2708_fb_setcolreg, ++ .fb_blank = bcm2708_fb_blank, ++ .fb_fillrect = bcm2708_fb_fillrect, ++ .fb_copyarea = bcm2708_fb_copyarea, ++ .fb_imageblit = bcm2708_fb_imageblit, ++ .fb_pan_display = bcm2708_fb_pan_display, ++ .fb_ioctl = bcm2708_ioctl, ++}; ++ ++static int bcm2708_fb_register(struct bcm2708_fb *fb) ++{ ++ int ret; ++ ++ fb->fb.fbops = &bcm2708_fb_ops; ++ fb->fb.flags = FBINFO_FLAG_DEFAULT | FBINFO_HWACCEL_COPYAREA; ++ fb->fb.pseudo_palette = fb->cmap; ++ ++ strncpy(fb->fb.fix.id, bcm2708_name, sizeof(fb->fb.fix.id)); ++ fb->fb.fix.type = FB_TYPE_PACKED_PIXELS; ++ fb->fb.fix.type_aux = 0; ++ fb->fb.fix.xpanstep = 1; ++ fb->fb.fix.ypanstep = 1; ++ fb->fb.fix.ywrapstep = 0; ++ fb->fb.fix.accel = FB_ACCEL_NONE; ++ ++ fb->fb.var.xres = fbwidth; ++ fb->fb.var.yres = fbheight; ++ fb->fb.var.xres_virtual = fbwidth; ++ fb->fb.var.yres_virtual = fbheight; ++ fb->fb.var.bits_per_pixel = fbdepth; ++ fb->fb.var.vmode = FB_VMODE_NONINTERLACED; ++ fb->fb.var.activate = FB_ACTIVATE_NOW; ++ fb->fb.var.nonstd = 0; ++ fb->fb.var.height = -1; /* height of picture in mm */ ++ fb->fb.var.width = -1; /* width of picture in mm */ ++ fb->fb.var.accel_flags = 0; ++ ++ fb->fb.monspecs.hfmin = 0; ++ fb->fb.monspecs.hfmax = 100000; ++ fb->fb.monspecs.vfmin = 0; ++ fb->fb.monspecs.vfmax = 400; ++ fb->fb.monspecs.dclkmin = 1000000; ++ fb->fb.monspecs.dclkmax = 100000000; ++ ++ bcm2708_fb_set_bitfields(&fb->fb.var); ++ init_waitqueue_head(&fb->dma_waitq); ++ ++ /* ++ * Allocate colourmap. ++ */ ++ ++ fb_set_var(&fb->fb, &fb->fb.var); ++ ret = bcm2708_fb_set_par(&fb->fb); ++ if (ret) ++ return ret; ++ ++ print_debug("BCM2708FB: registering framebuffer (%dx%d@%d) (%d)\n", ++ fbwidth, fbheight, fbdepth, fbswap); ++ ++ ret = register_framebuffer(&fb->fb); ++ print_debug("BCM2708FB: register framebuffer (%d)\n", ret); ++ if (ret == 0) ++ goto out; ++ ++ print_debug("BCM2708FB: cannot register framebuffer (%d)\n", ret); ++out: ++ return ret; ++} ++ ++static int bcm2708_fb_probe(struct platform_device *dev) ++{ ++ struct device_node *fw_np; ++ struct rpi_firmware *fw; ++ struct bcm2708_fb *fb; ++ int ret; ++ ++ fw_np = of_parse_phandle(dev->dev.of_node, "firmware", 0); ++/* Remove comment when booting without Device Tree is no longer supported ++ * if (!fw_np) { ++ * dev_err(&dev->dev, "Missing firmware node\n"); ++ * return -ENOENT; ++ * } ++ */ ++ fw = rpi_firmware_get(fw_np); ++ if (!fw) ++ return -EPROBE_DEFER; ++ ++ fb = kzalloc(sizeof(*fb), GFP_KERNEL); ++ if (!fb) { ++ ret = -ENOMEM; ++ goto free_region; ++ } ++ ++ fb->fw = fw; ++ bcm2708_fb_debugfs_init(fb); ++ ++ fb->cb_base = dma_alloc_wc(&dev->dev, SZ_64K, ++ &fb->cb_handle, GFP_KERNEL); ++ if (!fb->cb_base) { ++ dev_err(&dev->dev, "cannot allocate DMA CBs\n"); ++ ret = -ENOMEM; ++ goto free_fb; ++ } ++ ++ pr_info("BCM2708FB: allocated DMA memory %pad\n", &fb->cb_handle); ++ ++ ret = bcm_dma_chan_alloc(BCM_DMA_FEATURE_BULK, ++ &fb->dma_chan_base, &fb->dma_irq); ++ if (ret < 0) { ++ dev_err(&dev->dev, "couldn't allocate a DMA channel\n"); ++ goto free_cb; ++ } ++ fb->dma_chan = ret; ++ ++ ret = request_irq(fb->dma_irq, bcm2708_fb_dma_irq, ++ 0, "bcm2708_fb dma", fb); ++ if (ret) { ++ pr_err("%s: failed to request DMA irq\n", __func__); ++ goto free_dma_chan; ++ } ++ ++ pr_info("BCM2708FB: allocated DMA channel %d\n", fb->dma_chan); ++ ++ fb->dev = dev; ++ fb->fb.device = &dev->dev; ++ ++ /* failure here isn't fatal, but we'll fail in vc_mem_copy if ++ * fb->gpu is not valid ++ */ ++ rpi_firmware_property(fb->fw, RPI_FIRMWARE_GET_VC_MEMORY, &fb->gpu, ++ sizeof(fb->gpu)); ++ ++ ret = bcm2708_fb_register(fb); ++ if (ret == 0) { ++ platform_set_drvdata(dev, fb); ++ goto out; ++ } ++ ++free_dma_chan: ++ bcm_dma_chan_free(fb->dma_chan); ++free_cb: ++ dma_free_wc(&dev->dev, SZ_64K, fb->cb_base, fb->cb_handle); ++free_fb: ++ kfree(fb); ++free_region: ++ dev_err(&dev->dev, "probe failed, err %d\n", ret); ++out: ++ return ret; ++} ++ ++static int bcm2708_fb_remove(struct platform_device *dev) ++{ ++ struct bcm2708_fb *fb = platform_get_drvdata(dev); ++ ++ platform_set_drvdata(dev, NULL); ++ ++ if (fb->fb.screen_base) ++ iounmap(fb->fb.screen_base); ++ unregister_framebuffer(&fb->fb); ++ ++ dma_free_wc(&dev->dev, SZ_64K, fb->cb_base, fb->cb_handle); ++ bcm_dma_chan_free(fb->dma_chan); ++ ++ bcm2708_fb_debugfs_deinit(fb); ++ ++ free_irq(fb->dma_irq, fb); ++ ++ kfree(fb); ++ ++ return 0; ++} ++ ++static const struct of_device_id bcm2708_fb_of_match_table[] = { ++ { .compatible = "brcm,bcm2708-fb", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, bcm2708_fb_of_match_table); ++ ++static struct platform_driver bcm2708_fb_driver = { ++ .probe = bcm2708_fb_probe, ++ .remove = bcm2708_fb_remove, ++ .driver = { ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ .of_match_table = bcm2708_fb_of_match_table, ++ }, ++}; ++ ++static int __init bcm2708_fb_init(void) ++{ ++ return platform_driver_register(&bcm2708_fb_driver); ++} ++ ++module_init(bcm2708_fb_init); ++ ++static void __exit bcm2708_fb_exit(void) ++{ ++ platform_driver_unregister(&bcm2708_fb_driver); ++} ++ ++module_exit(bcm2708_fb_exit); ++ ++module_param(fbwidth, int, 0644); ++module_param(fbheight, int, 0644); ++module_param(fbdepth, int, 0644); ++module_param(fbswap, int, 0644); ++ ++MODULE_DESCRIPTION("BCM2708 framebuffer driver"); ++MODULE_LICENSE("GPL"); ++ ++MODULE_PARM_DESC(fbwidth, "Width of ARM Framebuffer"); ++MODULE_PARM_DESC(fbheight, "Height of ARM Framebuffer"); ++MODULE_PARM_DESC(fbdepth, "Bit depth of ARM Framebuffer"); ++MODULE_PARM_DESC(fbswap, "Swap order of red and blue in 24 and 32 bit modes"); +--- a/drivers/video/logo/logo_linux_clut224.ppm ++++ b/drivers/video/logo/logo_linux_clut224.ppm +@@ -1,1604 +1,883 @@ + P3 +-# Standard 224-color Linux logo +-80 80 ++63 80 + 255 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 6 6 6 6 6 6 10 10 10 10 10 10 +- 10 10 10 6 6 6 6 6 6 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 6 6 6 10 10 10 14 14 14 +- 22 22 22 26 26 26 30 30 30 34 34 34 +- 30 30 30 30 30 30 26 26 26 18 18 18 +- 14 14 14 10 10 10 6 6 6 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 1 0 0 1 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 6 6 6 14 14 14 26 26 26 42 42 42 +- 54 54 54 66 66 66 78 78 78 78 78 78 +- 78 78 78 74 74 74 66 66 66 54 54 54 +- 42 42 42 26 26 26 18 18 18 10 10 10 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 1 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 22 22 22 42 42 42 66 66 66 86 86 86 +- 66 66 66 38 38 38 38 38 38 22 22 22 +- 26 26 26 34 34 34 54 54 54 66 66 66 +- 86 86 86 70 70 70 46 46 46 26 26 26 +- 14 14 14 6 6 6 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 1 0 0 1 0 0 1 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 10 10 10 26 26 26 +- 50 50 50 82 82 82 58 58 58 6 6 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 6 6 6 54 54 54 86 86 86 66 66 66 +- 38 38 38 18 18 18 6 6 6 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 6 6 6 22 22 22 50 50 50 +- 78 78 78 34 34 34 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 6 6 6 70 70 70 +- 78 78 78 46 46 46 22 22 22 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 1 0 0 1 0 0 1 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 6 6 6 18 18 18 42 42 42 82 82 82 +- 26 26 26 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 14 14 14 +- 46 46 46 34 34 34 6 6 6 2 2 6 +- 42 42 42 78 78 78 42 42 42 18 18 18 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 1 0 0 0 0 0 1 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 10 10 10 30 30 30 66 66 66 58 58 58 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 26 26 26 +- 86 86 86 101 101 101 46 46 46 10 10 10 +- 2 2 6 58 58 58 70 70 70 34 34 34 +- 10 10 10 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 1 0 0 1 0 0 1 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 14 14 14 42 42 42 86 86 86 10 10 10 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 30 30 30 +- 94 94 94 94 94 94 58 58 58 26 26 26 +- 2 2 6 6 6 6 78 78 78 54 54 54 +- 22 22 22 6 6 6 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 6 6 6 +- 22 22 22 62 62 62 62 62 62 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 26 26 26 +- 54 54 54 38 38 38 18 18 18 10 10 10 +- 2 2 6 2 2 6 34 34 34 82 82 82 +- 38 38 38 14 14 14 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 1 0 0 1 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 6 6 6 +- 30 30 30 78 78 78 30 30 30 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 10 10 10 +- 10 10 10 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 78 78 78 +- 50 50 50 18 18 18 6 6 6 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 1 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 38 38 38 86 86 86 14 14 14 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 54 54 54 +- 66 66 66 26 26 26 6 6 6 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 1 0 0 1 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 14 14 14 +- 42 42 42 82 82 82 2 2 6 2 2 6 +- 2 2 6 6 6 6 10 10 10 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 6 6 6 +- 14 14 14 10 10 10 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 18 18 18 +- 82 82 82 34 34 34 10 10 10 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 1 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 14 14 14 +- 46 46 46 86 86 86 2 2 6 2 2 6 +- 6 6 6 6 6 6 22 22 22 34 34 34 +- 6 6 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 18 18 18 34 34 34 +- 10 10 10 50 50 50 22 22 22 2 2 6 +- 2 2 6 2 2 6 2 2 6 10 10 10 +- 86 86 86 42 42 42 14 14 14 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 1 0 0 1 0 0 1 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 14 14 14 +- 46 46 46 86 86 86 2 2 6 2 2 6 +- 38 38 38 116 116 116 94 94 94 22 22 22 +- 22 22 22 2 2 6 2 2 6 2 2 6 +- 14 14 14 86 86 86 138 138 138 162 162 162 +-154 154 154 38 38 38 26 26 26 6 6 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 86 86 86 46 46 46 14 14 14 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 14 14 14 +- 46 46 46 86 86 86 2 2 6 14 14 14 +-134 134 134 198 198 198 195 195 195 116 116 116 +- 10 10 10 2 2 6 2 2 6 6 6 6 +-101 98 89 187 187 187 210 210 210 218 218 218 +-214 214 214 134 134 134 14 14 14 6 6 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 86 86 86 50 50 50 18 18 18 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 1 0 0 0 +- 0 0 1 0 0 1 0 0 1 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 14 14 14 +- 46 46 46 86 86 86 2 2 6 54 54 54 +-218 218 218 195 195 195 226 226 226 246 246 246 +- 58 58 58 2 2 6 2 2 6 30 30 30 +-210 210 210 253 253 253 174 174 174 123 123 123 +-221 221 221 234 234 234 74 74 74 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 70 70 70 58 58 58 22 22 22 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 14 14 14 +- 46 46 46 82 82 82 2 2 6 106 106 106 +-170 170 170 26 26 26 86 86 86 226 226 226 +-123 123 123 10 10 10 14 14 14 46 46 46 +-231 231 231 190 190 190 6 6 6 70 70 70 +- 90 90 90 238 238 238 158 158 158 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 70 70 70 58 58 58 22 22 22 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 1 0 0 0 +- 0 0 1 0 0 1 0 0 1 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 14 14 14 +- 42 42 42 86 86 86 6 6 6 116 116 116 +-106 106 106 6 6 6 70 70 70 149 149 149 +-128 128 128 18 18 18 38 38 38 54 54 54 +-221 221 221 106 106 106 2 2 6 14 14 14 +- 46 46 46 190 190 190 198 198 198 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 74 74 74 62 62 62 22 22 22 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 1 0 0 0 +- 0 0 1 0 0 0 0 0 1 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 14 14 14 +- 42 42 42 94 94 94 14 14 14 101 101 101 +-128 128 128 2 2 6 18 18 18 116 116 116 +-118 98 46 121 92 8 121 92 8 98 78 10 +-162 162 162 106 106 106 2 2 6 2 2 6 +- 2 2 6 195 195 195 195 195 195 6 6 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 74 74 74 62 62 62 22 22 22 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 1 0 0 1 +- 0 0 1 0 0 0 0 0 1 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 38 38 38 90 90 90 14 14 14 58 58 58 +-210 210 210 26 26 26 54 38 6 154 114 10 +-226 170 11 236 186 11 225 175 15 184 144 12 +-215 174 15 175 146 61 37 26 9 2 2 6 +- 70 70 70 246 246 246 138 138 138 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 70 70 70 66 66 66 26 26 26 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 38 38 38 86 86 86 14 14 14 10 10 10 +-195 195 195 188 164 115 192 133 9 225 175 15 +-239 182 13 234 190 10 232 195 16 232 200 30 +-245 207 45 241 208 19 232 195 16 184 144 12 +-218 194 134 211 206 186 42 42 42 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 50 50 50 74 74 74 30 30 30 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 34 34 34 86 86 86 14 14 14 2 2 6 +-121 87 25 192 133 9 219 162 10 239 182 13 +-236 186 11 232 195 16 241 208 19 244 214 54 +-246 218 60 246 218 38 246 215 20 241 208 19 +-241 208 19 226 184 13 121 87 25 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 50 50 50 82 82 82 34 34 34 10 10 10 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 34 34 34 82 82 82 30 30 30 61 42 6 +-180 123 7 206 145 10 230 174 11 239 182 13 +-234 190 10 238 202 15 241 208 19 246 218 74 +-246 218 38 246 215 20 246 215 20 246 215 20 +-226 184 13 215 174 15 184 144 12 6 6 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 26 26 26 94 94 94 42 42 42 14 14 14 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 30 30 30 78 78 78 50 50 50 104 69 6 +-192 133 9 216 158 10 236 178 12 236 186 11 +-232 195 16 241 208 19 244 214 54 245 215 43 +-246 215 20 246 215 20 241 208 19 198 155 10 +-200 144 11 216 158 10 156 118 10 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 6 6 6 90 90 90 54 54 54 18 18 18 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 30 30 30 78 78 78 46 46 46 22 22 22 +-137 92 6 210 162 10 239 182 13 238 190 10 +-238 202 15 241 208 19 246 215 20 246 215 20 +-241 208 19 203 166 17 185 133 11 210 150 10 +-216 158 10 210 150 10 102 78 10 2 2 6 +- 6 6 6 54 54 54 14 14 14 2 2 6 +- 2 2 6 62 62 62 74 74 74 30 30 30 +- 10 10 10 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 34 34 34 78 78 78 50 50 50 6 6 6 +- 94 70 30 139 102 15 190 146 13 226 184 13 +-232 200 30 232 195 16 215 174 15 190 146 13 +-168 122 10 192 133 9 210 150 10 213 154 11 +-202 150 34 182 157 106 101 98 89 2 2 6 +- 2 2 6 78 78 78 116 116 116 58 58 58 +- 2 2 6 22 22 22 90 90 90 46 46 46 +- 18 18 18 6 6 6 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 38 38 38 86 86 86 50 50 50 6 6 6 +-128 128 128 174 154 114 156 107 11 168 122 10 +-198 155 10 184 144 12 197 138 11 200 144 11 +-206 145 10 206 145 10 197 138 11 188 164 115 +-195 195 195 198 198 198 174 174 174 14 14 14 +- 2 2 6 22 22 22 116 116 116 116 116 116 +- 22 22 22 2 2 6 74 74 74 70 70 70 +- 30 30 30 10 10 10 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 6 6 6 18 18 18 +- 50 50 50 101 101 101 26 26 26 10 10 10 +-138 138 138 190 190 190 174 154 114 156 107 11 +-197 138 11 200 144 11 197 138 11 192 133 9 +-180 123 7 190 142 34 190 178 144 187 187 187 +-202 202 202 221 221 221 214 214 214 66 66 66 +- 2 2 6 2 2 6 50 50 50 62 62 62 +- 6 6 6 2 2 6 10 10 10 90 90 90 +- 50 50 50 18 18 18 6 6 6 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 10 10 10 34 34 34 +- 74 74 74 74 74 74 2 2 6 6 6 6 +-144 144 144 198 198 198 190 190 190 178 166 146 +-154 121 60 156 107 11 156 107 11 168 124 44 +-174 154 114 187 187 187 190 190 190 210 210 210 +-246 246 246 253 253 253 253 253 253 182 182 182 +- 6 6 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 62 62 62 +- 74 74 74 34 34 34 14 14 14 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 10 10 10 22 22 22 54 54 54 +- 94 94 94 18 18 18 2 2 6 46 46 46 +-234 234 234 221 221 221 190 190 190 190 190 190 +-190 190 190 187 187 187 187 187 187 190 190 190 +-190 190 190 195 195 195 214 214 214 242 242 242 +-253 253 253 253 253 253 253 253 253 253 253 253 +- 82 82 82 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 14 14 14 +- 86 86 86 54 54 54 22 22 22 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 6 6 6 18 18 18 46 46 46 90 90 90 +- 46 46 46 18 18 18 6 6 6 182 182 182 +-253 253 253 246 246 246 206 206 206 190 190 190 +-190 190 190 190 190 190 190 190 190 190 190 190 +-206 206 206 231 231 231 250 250 250 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-202 202 202 14 14 14 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 42 42 42 86 86 86 42 42 42 18 18 18 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 6 6 6 +- 14 14 14 38 38 38 74 74 74 66 66 66 +- 2 2 6 6 6 6 90 90 90 250 250 250 +-253 253 253 253 253 253 238 238 238 198 198 198 +-190 190 190 190 190 190 195 195 195 221 221 221 +-246 246 246 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 82 82 82 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 78 78 78 70 70 70 34 34 34 +- 14 14 14 6 6 6 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 14 14 14 +- 34 34 34 66 66 66 78 78 78 6 6 6 +- 2 2 6 18 18 18 218 218 218 253 253 253 +-253 253 253 253 253 253 253 253 253 246 246 246 +-226 226 226 231 231 231 246 246 246 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 178 178 178 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 18 18 18 90 90 90 62 62 62 +- 30 30 30 10 10 10 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 10 10 10 26 26 26 +- 58 58 58 90 90 90 18 18 18 2 2 6 +- 2 2 6 110 110 110 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-250 250 250 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 231 231 231 18 18 18 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 18 18 18 94 94 94 +- 54 54 54 26 26 26 10 10 10 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 6 6 6 22 22 22 50 50 50 +- 90 90 90 26 26 26 2 2 6 2 2 6 +- 14 14 14 195 195 195 250 250 250 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-250 250 250 242 242 242 54 54 54 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 38 38 38 +- 86 86 86 50 50 50 22 22 22 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 6 6 6 14 14 14 38 38 38 82 82 82 +- 34 34 34 2 2 6 2 2 6 2 2 6 +- 42 42 42 195 195 195 246 246 246 253 253 253 +-253 253 253 253 253 253 253 253 253 250 250 250 +-242 242 242 242 242 242 250 250 250 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 250 250 250 246 246 246 238 238 238 +-226 226 226 231 231 231 101 101 101 6 6 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 38 38 38 82 82 82 42 42 42 14 14 14 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 10 10 10 26 26 26 62 62 62 66 66 66 +- 2 2 6 2 2 6 2 2 6 6 6 6 +- 70 70 70 170 170 170 206 206 206 234 234 234 +-246 246 246 250 250 250 250 250 250 238 238 238 +-226 226 226 231 231 231 238 238 238 250 250 250 +-250 250 250 250 250 250 246 246 246 231 231 231 +-214 214 214 206 206 206 202 202 202 202 202 202 +-198 198 198 202 202 202 182 182 182 18 18 18 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 62 62 62 66 66 66 30 30 30 +- 10 10 10 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 14 14 14 42 42 42 82 82 82 18 18 18 +- 2 2 6 2 2 6 2 2 6 10 10 10 +- 94 94 94 182 182 182 218 218 218 242 242 242 +-250 250 250 253 253 253 253 253 253 250 250 250 +-234 234 234 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 246 246 246 +-238 238 238 226 226 226 210 210 210 202 202 202 +-195 195 195 195 195 195 210 210 210 158 158 158 +- 6 6 6 14 14 14 50 50 50 14 14 14 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 6 6 6 86 86 86 46 46 46 +- 18 18 18 6 6 6 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 6 6 6 +- 22 22 22 54 54 54 70 70 70 2 2 6 +- 2 2 6 10 10 10 2 2 6 22 22 22 +-166 166 166 231 231 231 250 250 250 253 253 253 +-253 253 253 253 253 253 253 253 253 250 250 250 +-242 242 242 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 246 246 246 +-231 231 231 206 206 206 198 198 198 226 226 226 +- 94 94 94 2 2 6 6 6 6 38 38 38 +- 30 30 30 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 62 62 62 66 66 66 +- 26 26 26 10 10 10 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 30 30 30 74 74 74 50 50 50 2 2 6 +- 26 26 26 26 26 26 2 2 6 106 106 106 +-238 238 238 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 246 246 246 218 218 218 202 202 202 +-210 210 210 14 14 14 2 2 6 2 2 6 +- 30 30 30 22 22 22 2 2 6 2 2 6 +- 2 2 6 2 2 6 18 18 18 86 86 86 +- 42 42 42 14 14 14 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 14 14 14 +- 42 42 42 90 90 90 22 22 22 2 2 6 +- 42 42 42 2 2 6 18 18 18 218 218 218 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 250 250 250 221 221 221 +-218 218 218 101 101 101 2 2 6 14 14 14 +- 18 18 18 38 38 38 10 10 10 2 2 6 +- 2 2 6 2 2 6 2 2 6 78 78 78 +- 58 58 58 22 22 22 6 6 6 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 6 6 6 18 18 18 +- 54 54 54 82 82 82 2 2 6 26 26 26 +- 22 22 22 2 2 6 123 123 123 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 250 250 250 +-238 238 238 198 198 198 6 6 6 38 38 38 +- 58 58 58 26 26 26 38 38 38 2 2 6 +- 2 2 6 2 2 6 2 2 6 46 46 46 +- 78 78 78 30 30 30 10 10 10 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 10 10 10 30 30 30 +- 74 74 74 58 58 58 2 2 6 42 42 42 +- 2 2 6 22 22 22 231 231 231 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 250 250 250 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 246 246 246 46 46 46 38 38 38 +- 42 42 42 14 14 14 38 38 38 14 14 14 +- 2 2 6 2 2 6 2 2 6 6 6 6 +- 86 86 86 46 46 46 14 14 14 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 6 6 6 14 14 14 42 42 42 +- 90 90 90 18 18 18 18 18 18 26 26 26 +- 2 2 6 116 116 116 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 250 250 250 238 238 238 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 94 94 94 6 6 6 +- 2 2 6 2 2 6 10 10 10 34 34 34 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 74 74 74 58 58 58 22 22 22 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 10 10 10 26 26 26 66 66 66 +- 82 82 82 2 2 6 38 38 38 6 6 6 +- 14 14 14 210 210 210 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 246 246 246 242 242 242 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 144 144 144 2 2 6 +- 2 2 6 2 2 6 2 2 6 46 46 46 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 42 42 42 74 74 74 30 30 30 10 10 10 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 6 6 6 14 14 14 42 42 42 90 90 90 +- 26 26 26 6 6 6 42 42 42 2 2 6 +- 74 74 74 250 250 250 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 242 242 242 242 242 242 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 182 182 182 2 2 6 +- 2 2 6 2 2 6 2 2 6 46 46 46 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 10 10 10 86 86 86 38 38 38 10 10 10 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 10 10 10 26 26 26 66 66 66 82 82 82 +- 2 2 6 22 22 22 18 18 18 2 2 6 +-149 149 149 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 234 234 234 242 242 242 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 206 206 206 2 2 6 +- 2 2 6 2 2 6 2 2 6 38 38 38 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 6 6 6 86 86 86 46 46 46 14 14 14 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 6 6 6 +- 18 18 18 46 46 46 86 86 86 18 18 18 +- 2 2 6 34 34 34 10 10 10 6 6 6 +-210 210 210 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 234 234 234 242 242 242 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 221 221 221 6 6 6 +- 2 2 6 2 2 6 6 6 6 30 30 30 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 82 82 82 54 54 54 18 18 18 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 26 26 26 66 66 66 62 62 62 2 2 6 +- 2 2 6 38 38 38 10 10 10 26 26 26 +-238 238 238 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 231 231 231 238 238 238 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 231 231 231 6 6 6 +- 2 2 6 2 2 6 10 10 10 30 30 30 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 66 66 66 58 58 58 22 22 22 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 38 38 38 78 78 78 6 6 6 2 2 6 +- 2 2 6 46 46 46 14 14 14 42 42 42 +-246 246 246 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 231 231 231 242 242 242 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 234 234 234 10 10 10 +- 2 2 6 2 2 6 22 22 22 14 14 14 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 66 66 66 62 62 62 22 22 22 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 6 6 6 18 18 18 +- 50 50 50 74 74 74 2 2 6 2 2 6 +- 14 14 14 70 70 70 34 34 34 62 62 62 +-250 250 250 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 231 231 231 246 246 246 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 234 234 234 14 14 14 +- 2 2 6 2 2 6 30 30 30 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 66 66 66 62 62 62 22 22 22 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 6 6 6 18 18 18 +- 54 54 54 62 62 62 2 2 6 2 2 6 +- 2 2 6 30 30 30 46 46 46 70 70 70 +-250 250 250 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 231 231 231 246 246 246 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 226 226 226 10 10 10 +- 2 2 6 6 6 6 30 30 30 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 66 66 66 58 58 58 22 22 22 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 6 6 6 22 22 22 +- 58 58 58 62 62 62 2 2 6 2 2 6 +- 2 2 6 2 2 6 30 30 30 78 78 78 +-250 250 250 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 231 231 231 246 246 246 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 206 206 206 2 2 6 +- 22 22 22 34 34 34 18 14 6 22 22 22 +- 26 26 26 18 18 18 6 6 6 2 2 6 +- 2 2 6 82 82 82 54 54 54 18 18 18 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 6 6 6 26 26 26 +- 62 62 62 106 106 106 74 54 14 185 133 11 +-210 162 10 121 92 8 6 6 6 62 62 62 +-238 238 238 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 231 231 231 246 246 246 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 158 158 158 18 18 18 +- 14 14 14 2 2 6 2 2 6 2 2 6 +- 6 6 6 18 18 18 66 66 66 38 38 38 +- 6 6 6 94 94 94 50 50 50 18 18 18 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 6 6 6 +- 10 10 10 10 10 10 18 18 18 38 38 38 +- 78 78 78 142 134 106 216 158 10 242 186 14 +-246 190 14 246 190 14 156 118 10 10 10 10 +- 90 90 90 238 238 238 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 231 231 231 250 250 250 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 246 230 190 +-238 204 91 238 204 91 181 142 44 37 26 9 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 38 38 38 46 46 46 +- 26 26 26 106 106 106 54 54 54 18 18 18 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 6 6 6 14 14 14 22 22 22 +- 30 30 30 38 38 38 50 50 50 70 70 70 +-106 106 106 190 142 34 226 170 11 242 186 14 +-246 190 14 246 190 14 246 190 14 154 114 10 +- 6 6 6 74 74 74 226 226 226 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 231 231 231 250 250 250 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 228 184 62 +-241 196 14 241 208 19 232 195 16 38 30 10 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 6 6 6 30 30 30 26 26 26 +-203 166 17 154 142 90 66 66 66 26 26 26 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 6 6 6 18 18 18 38 38 38 58 58 58 +- 78 78 78 86 86 86 101 101 101 123 123 123 +-175 146 61 210 150 10 234 174 13 246 186 14 +-246 190 14 246 190 14 246 190 14 238 190 10 +-102 78 10 2 2 6 46 46 46 198 198 198 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 234 234 234 242 242 242 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 224 178 62 +-242 186 14 241 196 14 210 166 10 22 18 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 6 6 6 121 92 8 +-238 202 15 232 195 16 82 82 82 34 34 34 +- 10 10 10 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 14 14 14 38 38 38 70 70 70 154 122 46 +-190 142 34 200 144 11 197 138 11 197 138 11 +-213 154 11 226 170 11 242 186 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-225 175 15 46 32 6 2 2 6 22 22 22 +-158 158 158 250 250 250 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 250 250 250 242 242 242 224 178 62 +-239 182 13 236 186 11 213 154 11 46 32 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 61 42 6 225 175 15 +-238 190 10 236 186 11 112 100 78 42 42 42 +- 14 14 14 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 6 6 6 +- 22 22 22 54 54 54 154 122 46 213 154 11 +-226 170 11 230 174 11 226 170 11 226 170 11 +-236 178 12 242 186 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-241 196 14 184 144 12 10 10 10 2 2 6 +- 6 6 6 116 116 116 242 242 242 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 231 231 231 198 198 198 214 170 54 +-236 178 12 236 178 12 210 150 10 137 92 6 +- 18 14 6 2 2 6 2 2 6 2 2 6 +- 6 6 6 70 47 6 200 144 11 236 178 12 +-239 182 13 239 182 13 124 112 88 58 58 58 +- 22 22 22 6 6 6 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 30 30 30 70 70 70 180 133 36 226 170 11 +-239 182 13 242 186 14 242 186 14 246 186 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 232 195 16 98 70 6 2 2 6 +- 2 2 6 2 2 6 66 66 66 221 221 221 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 206 206 206 198 198 198 214 166 58 +-230 174 11 230 174 11 216 158 10 192 133 9 +-163 110 8 116 81 8 102 78 10 116 81 8 +-167 114 7 197 138 11 226 170 11 239 182 13 +-242 186 14 242 186 14 162 146 94 78 78 78 +- 34 34 34 14 14 14 6 6 6 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 6 6 6 +- 30 30 30 78 78 78 190 142 34 226 170 11 +-239 182 13 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 241 196 14 203 166 17 22 18 6 +- 2 2 6 2 2 6 2 2 6 38 38 38 +-218 218 218 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-250 250 250 206 206 206 198 198 198 202 162 69 +-226 170 11 236 178 12 224 166 10 210 150 10 +-200 144 11 197 138 11 192 133 9 197 138 11 +-210 150 10 226 170 11 242 186 14 246 190 14 +-246 190 14 246 186 14 225 175 15 124 112 88 +- 62 62 62 30 30 30 14 14 14 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 30 30 30 78 78 78 174 135 50 224 166 10 +-239 182 13 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 241 196 14 139 102 15 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 78 78 78 250 250 250 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-250 250 250 214 214 214 198 198 198 190 150 46 +-219 162 10 236 178 12 234 174 13 224 166 10 +-216 158 10 213 154 11 213 154 11 216 158 10 +-226 170 11 239 182 13 246 190 14 246 190 14 +-246 190 14 246 190 14 242 186 14 206 162 42 +-101 101 101 58 58 58 30 30 30 14 14 14 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 30 30 30 74 74 74 174 135 50 216 158 10 +-236 178 12 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 241 196 14 226 184 13 +- 61 42 6 2 2 6 2 2 6 2 2 6 +- 22 22 22 238 238 238 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 226 226 226 187 187 187 180 133 36 +-216 158 10 236 178 12 239 182 13 236 178 12 +-230 174 11 226 170 11 226 170 11 230 174 11 +-236 178 12 242 186 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 186 14 239 182 13 +-206 162 42 106 106 106 66 66 66 34 34 34 +- 14 14 14 6 6 6 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 6 6 6 +- 26 26 26 70 70 70 163 133 67 213 154 11 +-236 178 12 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 241 196 14 +-190 146 13 18 14 6 2 2 6 2 2 6 +- 46 46 46 246 246 246 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 221 221 221 86 86 86 156 107 11 +-216 158 10 236 178 12 242 186 14 246 186 14 +-242 186 14 239 182 13 239 182 13 242 186 14 +-242 186 14 246 186 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-242 186 14 225 175 15 142 122 72 66 66 66 +- 30 30 30 10 10 10 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 6 6 6 +- 26 26 26 70 70 70 163 133 67 210 150 10 +-236 178 12 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-232 195 16 121 92 8 34 34 34 106 106 106 +-221 221 221 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-242 242 242 82 82 82 18 14 6 163 110 8 +-216 158 10 236 178 12 242 186 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 242 186 14 163 133 67 +- 46 46 46 18 18 18 6 6 6 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 10 10 10 +- 30 30 30 78 78 78 163 133 67 210 150 10 +-236 178 12 246 186 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-241 196 14 215 174 15 190 178 144 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 218 218 218 +- 58 58 58 2 2 6 22 18 6 167 114 7 +-216 158 10 236 178 12 246 186 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 186 14 242 186 14 190 150 46 +- 54 54 54 22 22 22 6 6 6 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 14 14 14 +- 38 38 38 86 86 86 180 133 36 213 154 11 +-236 178 12 246 186 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 232 195 16 190 146 13 214 214 214 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 250 250 250 170 170 170 26 26 26 +- 2 2 6 2 2 6 37 26 9 163 110 8 +-219 162 10 239 182 13 246 186 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 186 14 236 178 12 224 166 10 142 122 72 +- 46 46 46 18 18 18 6 6 6 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 6 6 6 18 18 18 +- 50 50 50 109 106 95 192 133 9 224 166 10 +-242 186 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-242 186 14 226 184 13 210 162 10 142 110 46 +-226 226 226 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-253 253 253 253 253 253 253 253 253 253 253 253 +-198 198 198 66 66 66 2 2 6 2 2 6 +- 2 2 6 2 2 6 50 34 6 156 107 11 +-219 162 10 239 182 13 246 186 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 242 186 14 +-234 174 13 213 154 11 154 122 46 66 66 66 +- 30 30 30 10 10 10 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 6 6 6 22 22 22 +- 58 58 58 154 121 60 206 145 10 234 174 13 +-242 186 14 246 186 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 186 14 236 178 12 210 162 10 163 110 8 +- 61 42 6 138 138 138 218 218 218 250 250 250 +-253 253 253 253 253 253 253 253 253 250 250 250 +-242 242 242 210 210 210 144 144 144 66 66 66 +- 6 6 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 61 42 6 163 110 8 +-216 158 10 236 178 12 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 239 182 13 230 174 11 216 158 10 +-190 142 34 124 112 88 70 70 70 38 38 38 +- 18 18 18 6 6 6 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 6 6 6 22 22 22 +- 62 62 62 168 124 44 206 145 10 224 166 10 +-236 178 12 239 182 13 242 186 14 242 186 14 +-246 186 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 236 178 12 216 158 10 175 118 6 +- 80 54 7 2 2 6 6 6 6 30 30 30 +- 54 54 54 62 62 62 50 50 50 38 38 38 +- 14 14 14 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 6 6 6 80 54 7 167 114 7 +-213 154 11 236 178 12 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 190 14 242 186 14 239 182 13 239 182 13 +-230 174 11 210 150 10 174 135 50 124 112 88 +- 82 82 82 54 54 54 34 34 34 18 18 18 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 6 6 6 18 18 18 +- 50 50 50 158 118 36 192 133 9 200 144 11 +-216 158 10 219 162 10 224 166 10 226 170 11 +-230 174 11 236 178 12 239 182 13 239 182 13 +-242 186 14 246 186 14 246 190 14 246 190 14 +-246 190 14 246 190 14 246 190 14 246 190 14 +-246 186 14 230 174 11 210 150 10 163 110 8 +-104 69 6 10 10 10 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 6 6 6 91 60 6 167 114 7 +-206 145 10 230 174 11 242 186 14 246 190 14 +-246 190 14 246 190 14 246 186 14 242 186 14 +-239 182 13 230 174 11 224 166 10 213 154 11 +-180 133 36 124 112 88 86 86 86 58 58 58 +- 38 38 38 22 22 22 10 10 10 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 14 14 14 +- 34 34 34 70 70 70 138 110 50 158 118 36 +-167 114 7 180 123 7 192 133 9 197 138 11 +-200 144 11 206 145 10 213 154 11 219 162 10 +-224 166 10 230 174 11 239 182 13 242 186 14 +-246 186 14 246 186 14 246 186 14 246 186 14 +-239 182 13 216 158 10 185 133 11 152 99 6 +-104 69 6 18 14 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 2 2 6 2 2 6 2 2 6 +- 2 2 6 6 6 6 80 54 7 152 99 6 +-192 133 9 219 162 10 236 178 12 239 182 13 +-246 186 14 242 186 14 239 182 13 236 178 12 +-224 166 10 206 145 10 192 133 9 154 121 60 +- 94 94 94 62 62 62 42 42 42 22 22 22 +- 14 14 14 6 6 6 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 6 6 6 +- 18 18 18 34 34 34 58 58 58 78 78 78 +-101 98 89 124 112 88 142 110 46 156 107 11 +-163 110 8 167 114 7 175 118 6 180 123 7 +-185 133 11 197 138 11 210 150 10 219 162 10 +-226 170 11 236 178 12 236 178 12 234 174 13 +-219 162 10 197 138 11 163 110 8 130 83 6 +- 91 60 6 10 10 10 2 2 6 2 2 6 +- 18 18 18 38 38 38 38 38 38 38 38 38 +- 38 38 38 38 38 38 38 38 38 38 38 38 +- 38 38 38 38 38 38 26 26 26 2 2 6 +- 2 2 6 6 6 6 70 47 6 137 92 6 +-175 118 6 200 144 11 219 162 10 230 174 11 +-234 174 13 230 174 11 219 162 10 210 150 10 +-192 133 9 163 110 8 124 112 88 82 82 82 +- 50 50 50 30 30 30 14 14 14 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 6 6 6 14 14 14 22 22 22 34 34 34 +- 42 42 42 58 58 58 74 74 74 86 86 86 +-101 98 89 122 102 70 130 98 46 121 87 25 +-137 92 6 152 99 6 163 110 8 180 123 7 +-185 133 11 197 138 11 206 145 10 200 144 11 +-180 123 7 156 107 11 130 83 6 104 69 6 +- 50 34 6 54 54 54 110 110 110 101 98 89 +- 86 86 86 82 82 82 78 78 78 78 78 78 +- 78 78 78 78 78 78 78 78 78 78 78 78 +- 78 78 78 82 82 82 86 86 86 94 94 94 +-106 106 106 101 101 101 86 66 34 124 80 6 +-156 107 11 180 123 7 192 133 9 200 144 11 +-206 145 10 200 144 11 192 133 9 175 118 6 +-139 102 15 109 106 95 70 70 70 42 42 42 +- 22 22 22 10 10 10 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 6 6 6 10 10 10 +- 14 14 14 22 22 22 30 30 30 38 38 38 +- 50 50 50 62 62 62 74 74 74 90 90 90 +-101 98 89 112 100 78 121 87 25 124 80 6 +-137 92 6 152 99 6 152 99 6 152 99 6 +-138 86 6 124 80 6 98 70 6 86 66 30 +-101 98 89 82 82 82 58 58 58 46 46 46 +- 38 38 38 34 34 34 34 34 34 34 34 34 +- 34 34 34 34 34 34 34 34 34 34 34 34 +- 34 34 34 34 34 34 38 38 38 42 42 42 +- 54 54 54 82 82 82 94 86 76 91 60 6 +-134 86 6 156 107 11 167 114 7 175 118 6 +-175 118 6 167 114 7 152 99 6 121 87 25 +-101 98 89 62 62 62 34 34 34 18 18 18 +- 6 6 6 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 6 6 6 6 6 6 10 10 10 +- 18 18 18 22 22 22 30 30 30 42 42 42 +- 50 50 50 66 66 66 86 86 86 101 98 89 +-106 86 58 98 70 6 104 69 6 104 69 6 +-104 69 6 91 60 6 82 62 34 90 90 90 +- 62 62 62 38 38 38 22 22 22 14 14 14 +- 10 10 10 10 10 10 10 10 10 10 10 10 +- 10 10 10 10 10 10 6 6 6 10 10 10 +- 10 10 10 10 10 10 10 10 10 14 14 14 +- 22 22 22 42 42 42 70 70 70 89 81 66 +- 80 54 7 104 69 6 124 80 6 137 92 6 +-134 86 6 116 81 8 100 82 52 86 86 86 +- 58 58 58 30 30 30 14 14 14 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 6 6 6 10 10 10 14 14 14 +- 18 18 18 26 26 26 38 38 38 54 54 54 +- 70 70 70 86 86 86 94 86 76 89 81 66 +- 89 81 66 86 86 86 74 74 74 50 50 50 +- 30 30 30 14 14 14 6 6 6 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 6 6 6 18 18 18 34 34 34 58 58 58 +- 82 82 82 89 81 66 89 81 66 89 81 66 +- 94 86 66 94 86 76 74 74 74 50 50 50 +- 26 26 26 14 14 14 6 6 6 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 6 6 6 6 6 6 14 14 14 18 18 18 +- 30 30 30 38 38 38 46 46 46 54 54 54 +- 50 50 50 42 42 42 30 30 30 18 18 18 +- 10 10 10 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 6 6 6 14 14 14 26 26 26 +- 38 38 38 50 50 50 58 58 58 58 58 58 +- 54 54 54 42 42 42 30 30 30 18 18 18 +- 10 10 10 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 6 6 6 +- 6 6 6 10 10 10 14 14 14 18 18 18 +- 18 18 18 14 14 14 10 10 10 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 6 6 6 +- 14 14 14 18 18 18 22 22 22 22 22 22 +- 18 18 18 14 14 14 10 10 10 6 6 6 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 +- 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 1 0 ++0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 ++0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 ++10 15 3 2 3 1 12 18 4 42 61 14 19 27 6 11 16 4 ++38 55 13 10 15 3 3 4 1 10 15 3 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 3 1 ++12 18 4 1 1 0 23 34 8 31 45 11 10 15 3 32 47 11 ++34 49 12 3 4 1 3 4 1 3 4 1 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 10 15 3 29 42 10 26 37 9 12 18 4 ++55 80 19 81 118 28 55 80 19 92 132 31 106 153 36 69 100 23 ++100 144 34 80 116 27 42 61 14 81 118 28 23 34 8 27 40 9 ++15 21 5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 1 1 0 29 42 10 15 21 5 50 72 17 ++74 107 25 45 64 15 102 148 35 80 116 27 84 121 28 111 160 38 ++69 100 23 65 94 22 81 118 28 29 42 10 17 25 6 29 42 10 ++23 34 8 2 3 1 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 4 1 ++15 21 5 15 21 5 34 49 12 101 146 34 111 161 38 97 141 33 ++97 141 33 119 172 41 117 170 40 116 167 40 118 170 40 118 171 40 ++117 169 40 118 170 40 111 160 38 118 170 40 96 138 32 89 128 30 ++81 118 28 11 16 4 10 15 3 1 1 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++3 4 1 3 4 1 34 49 12 101 146 34 79 115 27 111 160 38 ++114 165 39 113 163 39 118 170 40 117 169 40 118 171 40 117 169 40 ++116 167 40 119 172 41 113 163 39 92 132 31 105 151 36 113 163 39 ++75 109 26 19 27 6 16 23 5 11 16 4 0 1 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 10 15 3 ++80 116 27 106 153 36 105 151 36 114 165 39 118 170 40 118 171 40 ++118 171 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 170 40 117 169 40 118 170 40 118 170 40 ++117 170 40 75 109 26 75 109 26 34 49 12 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 4 1 ++64 92 22 65 94 22 100 144 34 118 171 40 118 170 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 118 171 41 118 170 40 117 169 40 ++109 158 37 105 151 36 104 150 35 47 69 16 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++42 61 14 115 167 39 118 170 40 117 169 40 117 169 40 117 169 40 ++117 170 40 117 170 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 118 170 40 96 138 32 17 25 6 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 47 69 16 ++114 165 39 117 168 40 117 170 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 118 170 40 117 169 40 117 169 40 117 169 40 ++117 170 40 119 172 41 96 138 32 12 18 4 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 10 15 3 ++32 47 11 105 151 36 118 170 40 117 169 40 117 169 40 116 168 40 ++109 157 37 111 160 38 117 169 40 118 171 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 118 171 40 69 100 23 2 3 1 ++0 0 0 0 0 0 0 0 0 0 0 0 19 27 6 101 146 34 ++118 171 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 170 40 ++118 171 40 115 166 39 107 154 36 111 161 38 117 169 40 117 169 40 ++117 169 40 118 171 40 75 109 26 19 27 6 2 3 1 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 16 23 5 ++89 128 30 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++111 160 38 92 132 31 79 115 27 96 138 32 115 166 39 119 171 41 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 118 170 40 109 157 37 26 37 9 ++0 0 0 0 0 0 0 0 0 0 0 0 64 92 22 118 171 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 118 170 40 118 171 40 109 157 37 ++89 128 30 81 118 28 100 144 34 115 166 39 117 169 40 117 169 40 ++117 169 40 117 170 40 113 163 39 60 86 20 1 1 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++27 40 9 96 138 32 118 170 40 117 169 40 117 169 40 117 169 40 ++117 170 40 117 169 40 101 146 34 67 96 23 55 80 19 84 121 28 ++113 163 39 119 171 41 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 119 171 41 65 94 22 ++0 0 0 0 0 0 0 0 0 15 21 5 101 146 34 118 171 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 118 170 40 118 171 40 104 150 35 69 100 23 53 76 18 ++81 118 28 111 160 38 118 170 40 117 169 40 117 169 40 117 169 40 ++117 169 40 114 165 39 69 100 23 10 15 3 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 ++31 45 11 77 111 26 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 118 170 40 116 168 40 92 132 31 47 69 16 ++38 55 13 81 118 28 113 163 39 119 171 41 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 118 171 41 92 132 31 ++10 15 3 0 0 0 0 0 0 36 52 12 115 166 39 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 118 170 40 ++118 171 40 102 148 35 64 92 22 34 49 12 65 94 22 106 153 36 ++118 171 40 117 170 40 117 169 40 117 169 40 117 169 40 117 169 40 ++118 170 40 107 154 36 55 80 19 15 21 5 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++29 42 10 101 146 34 118 171 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 118 171 40 113 163 39 ++75 109 26 27 40 9 36 52 12 89 128 30 116 167 40 118 171 40 ++117 169 40 117 169 40 117 169 40 117 169 40 118 170 40 104 150 35 ++16 23 5 0 0 0 0 0 0 53 76 18 118 171 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 119 171 41 109 157 37 ++67 96 23 23 34 8 42 61 14 96 138 32 118 170 40 118 170 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 74 107 25 10 15 3 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 31 45 11 101 146 34 118 170 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++119 171 41 102 148 35 47 69 16 14 20 5 50 72 17 102 148 35 ++118 171 40 117 169 40 117 169 40 117 169 40 118 170 40 102 148 35 ++15 21 5 0 0 0 0 0 0 50 72 17 118 170 40 117 169 40 ++117 169 40 117 169 40 118 170 40 116 167 40 84 121 28 27 40 9 ++19 27 6 74 107 25 114 165 39 118 171 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 75 109 26 10 15 4 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 38 55 13 102 148 35 118 171 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 118 170 40 115 167 39 77 111 26 17 25 6 19 27 6 ++77 111 26 115 166 39 118 170 40 117 169 40 119 172 41 81 118 28 ++3 4 1 0 0 0 0 0 0 27 40 9 111 160 38 118 170 40 ++117 169 40 118 171 40 105 151 36 50 72 17 10 15 3 38 55 13 ++100 144 34 118 171 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 79 115 27 15 21 5 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 10 15 3 64 92 22 111 160 38 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 118 171 40 96 138 32 32 47 11 ++3 4 1 50 72 17 107 154 36 120 173 41 105 151 36 31 45 11 ++0 0 0 0 0 0 0 0 0 3 4 1 65 94 22 117 169 40 ++118 170 40 89 128 30 26 37 9 3 4 1 60 86 20 111 161 38 ++118 171 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++97 141 33 36 52 12 1 1 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 14 20 5 75 109 26 117 168 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 118 171 40 107 154 36 ++45 64 15 2 3 1 31 45 11 75 109 26 32 47 11 0 1 0 ++0 0 0 0 0 0 0 0 0 0 0 0 10 15 3 55 80 19 ++65 94 22 11 16 4 11 16 4 75 109 26 116 168 40 118 170 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 118 170 40 107 154 36 ++47 69 16 3 4 1 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 12 18 4 69 100 23 111 161 38 118 171 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 118 170 40 ++111 160 38 50 72 17 2 3 1 2 3 1 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 ++1 1 0 12 18 4 81 118 28 118 170 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 170 40 118 171 40 101 146 34 ++42 61 14 2 3 1 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 3 4 1 36 52 12 89 128 30 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++118 171 41 101 146 34 14 20 5 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 47 69 16 118 170 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 170 40 111 160 38 69 100 23 19 27 6 ++0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 11 16 4 69 100 23 ++115 167 39 119 172 41 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++119 172 41 75 109 26 3 4 1 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 23 34 8 106 153 36 118 170 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++117 169 40 118 170 40 119 172 41 105 151 36 42 61 14 2 3 1 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 15 21 5 ++45 64 15 80 116 27 114 165 39 118 170 40 117 169 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 119 172 41 ++97 141 33 20 30 7 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 1 1 0 53 76 18 114 165 39 118 171 40 117 169 40 ++117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 117 169 40 ++118 171 40 104 150 35 64 92 22 31 45 11 10 15 3 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 36 52 12 97 141 33 109 158 37 113 163 39 116 168 40 ++117 169 40 117 170 40 118 170 40 119 172 41 115 167 39 84 121 28 ++23 34 8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 3 4 1 50 72 17 102 148 35 118 171 40 ++119 171 41 118 170 40 117 169 40 117 169 40 115 166 39 111 161 38 ++109 157 37 79 115 27 12 18 4 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 3 4 1 15 21 5 23 34 8 45 64 15 106 153 36 ++116 167 40 111 160 38 101 146 34 79 115 27 42 61 14 10 15 3 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 1 1 0 20 30 7 60 86 20 ++89 128 30 106 153 36 113 163 39 117 169 40 84 121 28 29 42 10 ++19 27 6 10 15 3 2 3 1 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 16 23 5 38 55 13 ++36 52 12 26 37 9 12 18 4 2 3 1 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 1 0 0 19 2 7 52 5 18 ++78 7 27 88 8 31 81 7 29 56 5 19 25 2 9 3 0 1 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++3 4 1 19 27 6 31 45 11 38 55 13 32 47 11 3 4 1 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0 1 ++9 0 3 12 1 4 9 0 3 4 0 1 0 0 0 0 0 0 ++0 0 0 0 0 0 28 3 10 99 9 35 156 14 55 182 16 64 ++189 17 66 190 17 67 189 17 66 184 17 65 166 15 58 118 13 41 ++45 4 16 3 0 1 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 11 1 4 52 5 18 101 9 35 134 12 47 ++151 14 53 154 14 54 151 14 53 113 10 40 11 1 4 0 0 0 ++3 0 1 67 6 24 159 14 56 190 17 67 190 17 67 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 191 17 67 ++174 16 61 101 9 35 14 1 5 0 0 0 35 3 12 108 10 38 ++122 11 43 122 11 43 112 10 39 87 8 30 50 5 17 13 1 5 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++3 0 1 56 5 19 141 13 49 182 16 64 191 17 67 191 17 67 ++190 17 67 190 17 67 191 17 67 113 10 40 3 0 1 1 0 0 ++79 7 28 180 16 63 190 17 67 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++189 17 66 188 17 66 122 11 43 11 1 4 41 4 14 176 16 62 ++191 17 67 191 17 67 191 17 67 190 17 67 181 16 63 146 13 51 ++75 7 26 10 1 4 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 7 1 2 ++90 8 32 178 16 62 191 17 67 188 17 66 188 17 66 188 17 66 ++188 17 66 190 17 67 141 13 49 22 2 8 0 0 0 41 4 14 ++173 16 61 190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 88 8 31 1 0 0 89 8 31 ++185 17 65 189 17 66 188 17 66 188 17 66 189 17 66 191 17 67 ++186 17 65 124 11 43 25 2 9 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 2 0 1 89 8 31 ++184 17 65 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++190 17 67 151 14 53 34 3 12 0 0 0 0 0 0 79 7 28 ++190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 191 17 67 146 13 51 9 1 3 7 1 2 ++108 10 38 187 17 66 189 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 190 17 67 141 13 49 22 2 8 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 52 5 18 176 16 62 ++189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 ++151 14 53 38 3 13 0 0 0 0 0 0 0 0 0 50 5 17 ++180 16 63 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 191 17 67 141 13 49 7 1 3 0 0 0 ++11 1 4 112 10 39 187 17 66 189 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 190 17 67 113 10 40 5 0 2 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 7 1 3 132 12 46 191 17 67 ++188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 146 13 51 ++35 3 12 0 0 0 0 0 0 0 0 0 0 0 0 5 0 2 ++101 9 35 185 17 65 190 17 67 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 190 17 67 180 16 63 67 6 24 0 0 0 0 0 0 ++0 0 0 11 1 4 108 10 38 186 17 65 189 17 66 188 17 66 ++188 17 66 188 17 66 189 17 66 180 16 63 56 5 19 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 44 4 15 177 16 62 189 17 66 ++188 17 66 188 17 66 189 17 66 189 17 66 134 12 47 28 3 10 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++8 1 3 79 7 28 159 14 56 188 17 66 191 17 67 190 17 67 ++189 17 66 189 17 66 189 17 66 189 17 66 190 17 67 191 17 67 ++188 17 66 158 14 55 72 7 25 4 0 1 0 0 0 0 0 0 ++0 0 0 0 0 0 8 1 3 95 9 33 182 16 64 189 17 67 ++188 17 66 188 17 66 188 17 66 191 17 67 122 11 43 3 0 1 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 88 8 31 190 17 67 188 17 66 ++188 17 66 189 17 66 185 17 65 113 10 40 18 2 6 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 1 0 0 24 2 8 77 7 27 124 11 43 154 14 54 ++168 15 59 173 16 61 173 16 61 168 15 59 154 14 54 124 11 43 ++77 7 27 22 2 8 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 5 0 2 77 7 27 173 16 61 ++190 17 67 188 17 66 188 17 66 190 17 67 164 15 57 23 2 8 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 1 0 0 118 13 41 191 17 67 188 17 66 ++190 17 67 174 16 61 87 8 30 8 1 3 0 0 0 0 0 0 ++0 0 0 0 0 0 10 1 4 29 3 10 40 4 14 36 3 13 ++18 2 6 2 0 1 0 0 0 0 0 0 3 0 1 14 1 5 ++26 2 9 33 3 11 32 3 11 25 2 9 13 1 5 3 0 1 ++0 0 0 14 1 5 56 5 19 95 9 33 109 10 38 101 9 35 ++77 7 27 35 3 12 5 0 2 0 0 0 1 0 0 56 5 19 ++156 14 55 190 17 67 188 17 66 188 17 66 182 16 64 50 5 17 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 5 0 2 134 12 47 191 17 67 189 17 66 ++151 14 53 52 5 18 2 0 1 0 0 0 0 0 0 1 0 0 ++28 3 10 90 8 32 146 13 51 170 15 60 178 16 62 174 16 61 ++158 14 55 112 10 39 40 4 14 1 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0 1 ++56 5 19 146 13 51 183 17 64 191 17 67 191 17 67 191 17 67 ++188 17 66 173 16 61 122 11 43 41 4 14 1 0 0 0 0 0 ++30 3 10 124 11 43 185 17 65 190 17 67 187 17 66 67 6 24 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 6 1 2 134 12 47 168 15 59 99 9 35 ++21 2 7 0 0 0 0 0 0 0 0 0 6 1 2 77 7 27 ++162 15 57 190 17 67 191 17 67 189 17 66 189 17 66 189 17 66 ++190 17 67 191 17 67 169 15 59 75 7 26 3 0 1 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 2 0 1 79 7 28 ++178 16 62 191 17 67 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 189 17 66 191 17 67 170 15 60 79 7 28 5 0 2 ++0 0 0 10 1 3 78 7 27 159 14 56 188 17 66 75 7 26 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 1 0 0 35 3 12 29 3 10 2 0 1 ++0 0 0 0 0 0 0 0 0 9 1 3 101 9 35 183 17 64 ++190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 190 17 67 178 16 63 67 6 23 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 52 5 18 174 16 61 ++190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 190 17 67 182 16 64 89 8 31 ++4 0 1 0 0 0 0 0 0 25 2 9 73 7 26 31 3 11 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 4 0 1 98 9 34 187 17 66 189 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 190 17 67 158 14 55 25 2 9 ++0 0 0 0 0 0 0 0 0 8 1 3 134 12 47 191 17 67 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 189 17 66 180 16 63 ++68 6 24 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 6 1 2 19 2 7 3 0 1 0 0 0 0 0 0 ++0 0 0 0 0 0 65 6 23 180 16 63 189 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 189 17 66 83 8 29 ++0 0 0 0 0 0 0 0 0 41 4 14 177 16 62 189 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 ++159 14 56 28 3 10 0 0 0 0 0 0 0 0 0 23 2 8 ++41 4 14 5 0 2 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++23 2 8 113 10 40 159 14 56 65 6 23 0 0 0 0 0 0 ++0 0 0 16 1 6 146 13 51 191 17 67 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 191 17 67 132 12 46 ++5 0 2 0 0 0 0 0 0 77 7 27 189 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++190 17 67 98 9 34 0 0 0 0 0 0 12 1 4 134 12 47 ++178 16 63 108 10 38 16 1 6 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 30 3 10 ++141 13 49 190 17 67 191 17 67 134 12 47 6 1 2 0 0 0 ++0 0 0 68 6 24 186 17 65 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 156 14 55 ++14 1 5 0 0 0 0 0 0 98 9 34 191 17 67 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++190 17 67 156 14 55 19 2 7 0 0 0 47 4 16 181 16 63 ++190 17 67 189 17 66 126 14 44 17 2 6 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 16 1 6 134 12 47 ++191 17 67 188 17 66 190 17 67 162 15 57 19 2 7 0 0 0 ++3 0 1 123 11 43 191 17 67 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 163 15 57 ++20 2 7 0 0 0 0 0 0 101 9 35 191 17 67 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 182 16 64 52 5 18 0 0 0 73 7 26 188 17 66 ++188 17 66 188 17 66 189 17 66 109 10 38 5 0 2 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 95 9 33 189 17 66 ++188 17 66 188 17 66 189 17 66 171 15 60 29 3 10 0 0 0 ++16 1 6 156 14 55 190 17 67 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 158 14 55 ++17 2 6 0 0 0 0 0 0 85 8 30 190 17 67 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 189 17 66 81 7 29 0 0 0 85 8 30 190 17 67 ++188 17 66 188 17 66 189 17 66 180 16 63 56 5 19 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 25 2 9 162 15 57 190 17 67 ++188 17 66 188 17 66 189 17 66 173 16 61 31 3 11 0 0 0 ++30 3 10 171 15 60 189 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 191 17 67 141 13 49 ++7 1 2 0 0 0 0 0 0 56 5 19 183 17 64 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 191 17 67 98 9 34 0 0 0 88 8 31 190 17 67 ++188 17 66 188 17 66 188 17 66 191 17 67 124 11 43 5 0 2 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 68 6 24 187 17 66 188 17 66 ++188 17 66 188 17 66 189 17 66 170 15 60 28 3 10 0 0 0 ++34 3 12 174 16 61 189 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 191 17 67 101 9 35 ++0 0 0 0 0 0 0 0 0 21 2 7 159 14 56 190 17 67 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 191 17 67 98 9 34 0 0 0 81 7 29 189 17 66 ++188 17 66 188 17 66 188 17 66 189 17 66 168 15 59 28 3 10 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 109 10 38 191 17 67 188 17 66 ++188 17 66 188 17 66 190 17 67 163 15 57 21 2 7 0 0 0 ++26 2 9 168 15 59 189 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 189 17 66 180 16 63 47 4 16 ++0 0 0 0 0 0 0 0 0 0 0 0 108 10 38 190 17 67 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 189 17 66 78 7 27 0 0 0 68 6 24 187 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 183 17 64 56 5 19 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 3 0 1 131 12 46 191 17 67 188 17 66 ++188 17 66 188 17 66 190 17 67 151 14 53 12 1 4 0 0 0 ++11 1 4 146 13 51 190 17 67 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 191 17 67 126 14 44 7 1 2 ++0 0 0 0 0 0 0 0 0 0 0 0 32 3 11 164 15 58 ++190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++189 17 66 178 16 62 44 4 15 0 0 0 50 5 17 182 16 64 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 72 7 25 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 5 0 2 134 12 47 191 17 67 188 17 66 ++188 17 66 188 17 66 191 17 67 131 12 46 3 0 1 0 0 0 ++0 0 0 101 9 35 190 17 67 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 190 17 67 170 15 60 44 4 15 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 77 7 27 ++183 17 64 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++191 17 67 134 12 47 9 1 3 0 0 0 31 3 11 171 15 60 ++189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 72 7 25 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 2 0 1 124 11 43 191 17 67 188 17 66 ++188 17 66 188 17 66 191 17 67 101 9 35 0 0 0 0 0 0 ++0 0 0 35 3 12 168 15 59 190 17 67 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 189 17 66 182 16 64 77 7 27 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 6 1 2 ++99 9 35 185 17 65 189 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 189 17 66 ++177 16 62 56 5 19 0 0 0 0 0 0 13 1 5 151 14 53 ++190 17 67 188 17 66 188 17 66 188 17 66 185 17 65 56 5 19 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 99 9 35 191 17 67 188 17 66 ++188 17 66 188 17 66 186 17 65 65 6 23 0 0 0 0 0 0 ++0 0 0 0 0 0 79 7 28 182 16 64 190 17 67 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++191 17 67 177 16 62 83 8 29 4 0 1 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++8 1 3 89 8 31 175 16 62 191 17 67 189 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 181 16 63 ++85 8 30 3 0 1 0 0 0 0 0 0 1 0 0 118 13 41 ++191 17 67 188 17 66 188 17 66 189 17 66 173 16 61 34 3 12 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 56 5 19 183 17 64 188 17 66 ++188 17 66 189 17 66 169 15 59 30 3 10 0 0 0 0 0 0 ++0 0 0 0 0 0 5 0 2 83 8 29 173 16 61 191 17 67 ++190 17 67 189 17 66 189 17 66 190 17 67 191 17 67 187 17 66 ++151 14 53 56 5 19 3 0 1 0 0 0 16 1 6 50 5 17 ++79 7 28 95 9 33 95 9 33 75 7 26 41 4 14 10 1 4 ++0 0 0 2 0 1 50 5 17 132 12 46 178 16 62 190 17 67 ++191 17 67 191 17 67 191 17 67 186 17 65 154 14 54 68 6 24 ++4 0 1 0 0 0 0 0 0 0 0 0 0 0 0 72 7 25 ++187 17 66 188 17 66 188 17 66 191 17 67 141 13 49 9 1 3 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 14 1 5 151 14 53 190 17 67 ++188 17 66 191 17 67 131 12 46 5 0 2 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 2 0 1 44 4 15 113 10 40 ++156 14 55 173 16 61 174 16 61 164 15 58 134 12 47 77 7 27 ++18 2 6 0 0 0 16 1 6 85 8 30 151 14 53 182 16 64 ++189 17 66 191 17 67 190 17 67 188 17 66 177 16 62 141 13 49 ++68 6 24 8 1 3 0 0 0 8 1 3 44 4 15 88 8 31 ++113 10 40 122 11 43 108 10 38 67 6 24 20 2 7 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 28 3 10 ++166 15 58 190 17 67 188 17 66 187 17 66 79 7 28 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 73 7 26 185 17 65 ++189 17 66 184 17 65 65 6 23 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 0 1 ++17 2 6 32 3 11 34 3 12 22 2 8 6 1 2 0 0 0 ++0 0 0 38 3 13 141 13 49 188 17 66 190 17 67 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 189 17 66 191 17 67 ++184 17 65 122 11 43 21 2 7 0 0 0 0 0 0 0 0 0 ++0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 ++108 10 38 191 17 67 191 17 67 141 13 49 16 1 6 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 8 1 3 112 10 39 ++186 17 65 124 11 43 10 1 4 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++36 3 13 156 14 55 191 17 67 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++189 17 66 190 17 67 134 12 47 18 2 6 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 7 1 2 41 4 14 75 7 26 66 5 23 19 2 7 ++26 2 9 144 13 50 154 14 54 40 4 14 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 13 1 5 ++56 5 19 19 2 7 0 0 0 7 1 2 29 3 10 35 3 12 ++19 2 7 2 0 1 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 13 1 5 ++134 12 47 191 17 67 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 189 17 67 108 10 38 3 0 1 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 ++40 4 14 124 11 43 177 16 62 188 17 66 187 17 66 144 13 50 ++24 2 8 17 2 6 22 2 8 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 19 2 7 122 11 43 171 15 60 175 16 62 ++159 14 56 112 10 39 40 4 14 2 0 1 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 72 7 25 ++186 17 65 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 189 17 66 174 16 61 41 4 14 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 3 0 1 72 7 25 ++168 15 59 191 17 67 189 17 66 188 17 66 188 17 66 190 17 67 ++95 9 33 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 95 9 33 191 17 67 189 17 66 189 17 66 ++190 17 67 191 17 67 171 15 60 90 8 32 12 1 4 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 5 0 2 132 12 46 ++191 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 190 17 67 98 9 34 0 0 0 ++0 0 0 0 0 0 0 0 0 5 0 2 88 8 31 180 16 63 ++190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 191 17 67 ++146 13 51 11 1 4 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 9 1 3 144 13 50 191 17 67 188 17 66 188 17 66 ++188 17 66 188 17 66 189 17 66 187 17 66 123 11 43 20 2 7 ++0 0 0 0 0 0 0 0 0 0 0 0 21 2 7 163 15 57 ++190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 191 17 67 134 12 47 5 0 2 ++0 0 0 0 0 0 3 0 1 88 8 31 182 16 64 189 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 189 17 66 ++171 15 60 31 3 11 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 20 2 7 162 15 57 190 17 67 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 132 12 46 ++20 2 7 0 0 0 0 0 0 0 0 0 32 3 11 173 16 61 ++189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 190 17 67 151 14 53 12 1 4 ++0 0 0 0 0 0 72 7 25 180 16 63 189 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++181 16 63 47 4 16 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 21 2 7 163 15 57 190 17 67 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 ++122 11 43 9 1 3 0 0 0 0 0 0 30 3 10 171 15 60 ++189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 190 17 67 146 13 51 10 1 4 ++0 0 0 38 3 13 166 15 58 190 17 67 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++183 17 64 52 5 18 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 13 1 5 154 14 54 190 17 67 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++186 17 65 79 7 28 0 0 0 0 0 0 14 1 5 156 14 54 ++190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 191 17 67 124 11 43 2 0 1 ++5 0 2 122 11 43 191 17 67 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++182 16 64 47 4 16 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 3 0 1 126 14 44 191 17 67 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++190 17 67 158 14 55 23 2 8 0 0 0 1 0 0 113 10 40 ++191 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 78 7 27 0 0 0 ++47 4 16 177 16 62 189 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 189 17 66 ++173 16 61 34 3 12 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 85 8 30 189 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 79 7 28 0 0 0 0 0 0 47 4 16 ++175 16 62 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 190 17 67 156 14 55 22 2 8 0 0 0 ++109 10 38 191 17 67 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 ++151 14 53 13 1 5 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 35 3 12 173 16 61 189 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 191 17 67 134 12 47 7 1 2 0 0 0 3 0 1 ++99 9 35 188 17 66 189 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 189 17 66 181 16 63 68 6 24 0 0 0 18 2 6 ++156 14 55 190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 ++101 9 35 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 3 0 1 118 13 41 191 17 67 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 189 17 66 168 15 59 28 3 10 0 0 0 0 0 0 ++12 1 4 113 10 40 187 17 66 189 17 67 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++190 17 67 180 16 63 88 8 31 4 0 1 0 0 0 47 4 16 ++180 16 63 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 190 17 67 168 15 59 ++36 3 13 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 38 3 13 164 15 58 190 17 67 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 182 16 64 50 5 17 0 0 0 0 0 0 ++0 0 0 11 1 4 90 8 32 169 15 59 190 17 67 190 17 67 ++189 17 66 189 17 66 189 17 66 189 17 66 191 17 67 189 17 66 ++158 14 55 68 6 24 4 0 1 0 0 0 0 0 0 73 7 26 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 189 17 66 185 17 65 83 8 29 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 65 6 23 174 16 61 ++190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 185 17 65 56 5 19 0 0 0 0 0 0 ++0 0 0 0 0 0 2 0 1 35 3 12 99 9 35 146 13 51 ++170 15 60 177 16 62 177 16 62 166 15 58 141 13 49 85 8 30 ++24 2 8 0 0 0 0 0 0 0 0 0 0 0 0 85 8 30 ++190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 189 17 66 112 10 39 8 1 3 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 68 6 24 ++170 15 60 191 17 67 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 182 16 64 50 5 17 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 11 1 4 ++28 3 10 40 4 14 38 3 13 25 2 9 8 1 3 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 78 7 27 ++189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 189 17 66 187 17 66 113 10 40 14 1 5 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 ++47 4 16 141 13 49 186 17 65 191 17 67 190 17 67 189 17 66 ++189 17 66 191 17 67 156 14 55 20 2 7 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 44 4 15 ++178 16 62 190 17 67 188 17 66 188 17 66 188 17 66 190 17 67 ++191 17 67 173 16 61 90 8 32 10 1 4 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 14 1 5 68 6 24 131 12 46 162 15 57 174 16 61 ++171 15 60 146 13 51 56 5 19 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 3 0 1 14 1 5 29 3 10 ++41 4 14 47 4 16 50 5 17 45 4 16 34 3 12 18 2 6 ++5 0 2 0 0 0 0 0 0 0 0 0 0 0 0 5 0 2 ++90 8 32 169 15 59 185 17 65 187 17 66 182 16 64 163 15 57 ++113 10 40 41 4 14 2 0 1 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 5 0 2 21 2 7 34 3 12 ++29 3 10 11 1 4 0 0 0 0 0 0 0 0 0 0 0 0 ++3 0 1 32 3 11 79 7 28 124 11 43 154 14 54 171 15 60 ++180 16 63 182 16 64 182 16 64 180 16 63 174 16 61 159 14 56 ++132 12 46 88 8 31 34 3 12 3 0 1 0 0 0 0 0 0 ++3 0 1 29 3 10 56 5 19 65 6 23 50 5 17 23 2 8 ++3 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 25 2 9 ++109 10 38 169 15 59 189 17 66 191 17 67 190 17 67 189 17 66 ++189 17 66 188 17 66 188 17 66 188 17 66 189 17 66 190 17 67 ++191 17 67 190 17 67 171 15 60 98 9 34 10 1 3 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 14 1 5 141 13 49 ++191 17 67 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 189 17 67 186 17 65 65 6 23 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 23 2 8 166 15 58 ++190 17 67 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 189 17 66 176 16 62 45 4 16 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 83 8 29 ++183 17 64 189 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++188 17 66 189 17 66 185 17 65 95 9 33 3 0 1 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 5 0 2 ++85 8 30 176 16 62 191 17 67 188 17 66 188 17 66 188 17 66 ++188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 188 17 66 ++191 17 67 180 16 63 95 9 33 7 1 3 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++2 0 1 52 5 18 141 13 49 185 17 65 191 17 67 189 17 67 ++189 17 66 188 17 66 188 17 66 189 17 66 191 17 67 187 17 66 ++146 13 51 56 5 19 4 0 1 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 14 1 5 68 6 24 131 12 46 166 15 58 ++180 16 63 183 17 64 180 16 63 168 15 59 134 12 47 75 7 26 ++17 2 6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 5 0 2 24 2 8 ++44 4 15 52 5 18 45 4 16 26 2 9 6 1 2 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ++0 0 0 0 0 0 0 0 0 +--- a/include/soc/bcm2835/raspberrypi-firmware.h ++++ b/include/soc/bcm2835/raspberrypi-firmware.h +@@ -123,6 +123,7 @@ enum rpi_firmware_property_tag { + RPI_FIRMWARE_FRAMEBUFFER_SET_DEPTH = 0x00048005, + RPI_FIRMWARE_FRAMEBUFFER_SET_PIXEL_ORDER = 0x00048006, + RPI_FIRMWARE_FRAMEBUFFER_SET_ALPHA_MODE = 0x00048007, ++ RPI_FIRMWARE_FRAMEBUFFER_SET_PITCH = 0x00048008, + RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_OFFSET = 0x00048009, + RPI_FIRMWARE_FRAMEBUFFER_SET_OVERSCAN = 0x0004800a, + RPI_FIRMWARE_FRAMEBUFFER_SET_PALETTE = 0x0004800b, diff --git a/target/linux/bcm27xx/patches-5.10/950-0042-Pulled-in-the-multi-frame-buffer-support-from-the-Pi.patch b/target/linux/bcm27xx/patches-5.10/950-0042-Pulled-in-the-multi-frame-buffer-support-from-the-Pi.patch new file mode 100644 index 0000000000..884753f872 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0042-Pulled-in-the-multi-frame-buffer-support-from-the-Pi.patch @@ -0,0 +1,828 @@ +From 4ac7128970e15d83ef3c2a65e65ca9ee4096c9d1 Mon Sep 17 00:00:00 2001 +From: James Hughes +Date: Thu, 14 Mar 2019 13:27:54 +0000 +Subject: [PATCH] Pulled in the multi frame buffer support from the Pi3 + repo + +--- + drivers/video/fbdev/bcm2708_fb.c | 457 +++++++++++++++------ + include/soc/bcm2835/raspberrypi-firmware.h | 13 + + 2 files changed, 337 insertions(+), 133 deletions(-) + +--- a/drivers/video/fbdev/bcm2708_fb.c ++++ b/drivers/video/fbdev/bcm2708_fb.c +@@ -2,6 +2,7 @@ + * linux/drivers/video/bcm2708_fb.c + * + * Copyright (C) 2010 Broadcom ++ * Copyright (C) 2018 Raspberry Pi (Trading) Ltd + * + * This file is subject to the terms and conditions of the GNU General Public + * License. See the file COPYING in the main directory of this archive +@@ -13,6 +14,7 @@ + * Copyright 1999-2001 Jeff Garzik + * + */ ++ + #include + #include + #include +@@ -33,6 +35,7 @@ + #include + #include + #include ++#include + + //#define BCM2708_FB_DEBUG + #define MODULE_NAME "bcm2708_fb" +@@ -79,64 +82,150 @@ struct bcm2708_fb_stats { + u32 dma_irqs; + }; + ++struct vc4_display_settings_t { ++ u32 display_num; ++ u32 width; ++ u32 height; ++ u32 depth; ++ u32 pitch; ++ u32 virtual_width; ++ u32 virtual_height; ++ u32 virtual_width_offset; ++ u32 virtual_height_offset; ++ unsigned long fb_bus_address; ++}; ++ ++struct bcm2708_fb_dev; ++ + struct bcm2708_fb { + struct fb_info fb; + struct platform_device *dev; +- struct rpi_firmware *fw; + u32 cmap[16]; + u32 gpu_cmap[256]; +- int dma_chan; +- int dma_irq; +- void __iomem *dma_chan_base; +- void *cb_base; /* DMA control blocks */ +- dma_addr_t cb_handle; + struct dentry *debugfs_dir; +- wait_queue_head_t dma_waitq; +- struct bcm2708_fb_stats stats; ++ struct dentry *debugfs_subdir; + unsigned long fb_bus_address; +- bool disable_arm_alloc; ++ struct { u32 base, length; } gpu; ++ struct vc4_display_settings_t display_settings; ++ struct debugfs_regset32 screeninfo_regset; ++ struct bcm2708_fb_dev *fbdev; + unsigned int image_size; + dma_addr_t dma_addr; + void *cpuaddr; + }; + ++#define MAX_FRAMEBUFFERS 3 ++ ++struct bcm2708_fb_dev { ++ int firmware_supports_multifb; ++ /* Protects the DMA system from multiple FB access */ ++ struct mutex dma_mutex; ++ int dma_chan; ++ int dma_irq; ++ void __iomem *dma_chan_base; ++ wait_queue_head_t dma_waitq; ++ bool disable_arm_alloc; ++ struct bcm2708_fb_stats dma_stats; ++ void *cb_base; /* DMA control blocks */ ++ dma_addr_t cb_handle; ++ int instance_count; ++ int num_displays; ++ struct rpi_firmware *fw; ++ struct bcm2708_fb displays[MAX_FRAMEBUFFERS]; ++}; ++ + #define to_bcm2708(info) container_of(info, struct bcm2708_fb, fb) + + static void bcm2708_fb_debugfs_deinit(struct bcm2708_fb *fb) + { +- debugfs_remove_recursive(fb->debugfs_dir); +- fb->debugfs_dir = NULL; ++ debugfs_remove_recursive(fb->debugfs_subdir); ++ fb->debugfs_subdir = NULL; ++ ++ fb->fbdev->instance_count--; ++ ++ if (!fb->fbdev->instance_count) { ++ debugfs_remove_recursive(fb->debugfs_dir); ++ fb->debugfs_dir = NULL; ++ } + } + + static int bcm2708_fb_debugfs_init(struct bcm2708_fb *fb) + { ++ char buf[3]; ++ struct bcm2708_fb_dev *fbdev = fb->fbdev; ++ + static struct debugfs_reg32 stats_registers[] = { +- { +- "dma_copies", +- offsetof(struct bcm2708_fb_stats, dma_copies) +- }, +- { +- "dma_irqs", +- offsetof(struct bcm2708_fb_stats, dma_irqs) +- }, ++ {"dma_copies", offsetof(struct bcm2708_fb_stats, dma_copies)}, ++ {"dma_irqs", offsetof(struct bcm2708_fb_stats, dma_irqs)}, + }; + +- fb->debugfs_dir = debugfs_create_dir(DRIVER_NAME, NULL); ++ static struct debugfs_reg32 screeninfo[] = { ++ {"width", offsetof(struct fb_var_screeninfo, xres)}, ++ {"height", offsetof(struct fb_var_screeninfo, yres)}, ++ {"bpp", offsetof(struct fb_var_screeninfo, bits_per_pixel)}, ++ {"xres_virtual", offsetof(struct fb_var_screeninfo, xres_virtual)}, ++ {"yres_virtual", offsetof(struct fb_var_screeninfo, yres_virtual)}, ++ {"xoffset", offsetof(struct fb_var_screeninfo, xoffset)}, ++ {"yoffset", offsetof(struct fb_var_screeninfo, yoffset)}, ++ }; ++ ++ fb->debugfs_dir = debugfs_lookup(DRIVER_NAME, NULL); ++ ++ if (!fb->debugfs_dir) ++ fb->debugfs_dir = debugfs_create_dir(DRIVER_NAME, NULL); ++ + if (!fb->debugfs_dir) { +- pr_warn("%s: could not create debugfs entry\n", +- __func__); ++ dev_warn(fb->fb.dev, "%s: could not create debugfs folder\n", ++ __func__); + return -EFAULT; + } + +- fb->stats.regset.regs = stats_registers; +- fb->stats.regset.nregs = ARRAY_SIZE(stats_registers); +- fb->stats.regset.base = &fb->stats; ++ snprintf(buf, sizeof(buf), "%u", fb->display_settings.display_num); ++ ++ fb->debugfs_subdir = debugfs_create_dir(buf, fb->debugfs_dir); + + debugfs_create_regset32("stats", 0444, fb->debugfs_dir, + &fb->stats.regset); ++ ++ if (!fb->debugfs_subdir) { ++ dev_warn(fb->fb.dev, "%s: could not create debugfs entry %u\n", ++ __func__, fb->display_settings.display_num); ++ return -EFAULT; ++ } ++ ++ fbdev->dma_stats.regset.regs = stats_registers; ++ fbdev->dma_stats.regset.nregs = ARRAY_SIZE(stats_registers); ++ fbdev->dma_stats.regset.base = &fbdev->dma_stats; ++ ++ debugfs_create_regset32("dma_stats", 0444, fb->debugfs_subdir, ++ &fbdev->dma_stats.regset); ++ ++ fb->screeninfo_regset.regs = screeninfo; ++ fb->screeninfo_regset.nregs = ARRAY_SIZE(screeninfo); ++ fb->screeninfo_regset.base = &fb->fb.var; ++ ++ debugfs_create_regset32("screeninfo", 0444, fb->debugfs_subdir, ++ &fb->screeninfo_regset); ++ ++ fbdev->instance_count++; ++ + return 0; + } + ++static void set_display_num(struct bcm2708_fb *fb) ++{ ++ if (fb && fb->fbdev && fb->fbdev->firmware_supports_multifb) { ++ u32 tmp = fb->display_settings.display_num; ++ ++ if (rpi_firmware_property(fb->fbdev->fw, ++ RPI_FIRMWARE_FRAMEBUFFER_SET_DISPLAY_NUM, ++ &tmp, ++ sizeof(tmp))) ++ dev_warn_once(fb->fb.dev, ++ "Set display number call failed. Old GPU firmware?"); ++ } ++} ++ + static int bcm2708_fb_set_bitfields(struct fb_var_screeninfo *var) + { + int ret = 0; +@@ -214,11 +303,11 @@ static int bcm2708_fb_check_var(struct f + struct fb_info *info) + { + /* info input, var output */ +- print_debug("%s(%p) %dx%d (%dx%d), %d, %d\n", ++ print_debug("%s(%p) %ux%u (%ux%u), %ul, %u\n", + __func__, info, info->var.xres, info->var.yres, + info->var.xres_virtual, info->var.yres_virtual, +- (int)info->screen_size, info->var.bits_per_pixel); +- print_debug("%s(%p) %dx%d (%dx%d), %d\n", __func__, var, var->xres, ++ info->screen_size, info->var.bits_per_pixel); ++ print_debug("%s(%p) %ux%u (%ux%u), %u\n", __func__, var, var->xres, + var->yres, var->xres_virtual, var->yres_virtual, + var->bits_per_pixel); + +@@ -281,17 +370,24 @@ static int bcm2708_fb_set_par(struct fb_ + }; + int ret, image_size; + +- +- print_debug("%s(%p) %dx%d (%dx%d), %d, %d\n", __func__, info, ++ print_debug("%s(%p) %dx%d (%dx%d), %d, %d (display %d)\n", __func__, ++ info, + info->var.xres, info->var.yres, info->var.xres_virtual, + info->var.yres_virtual, (int)info->screen_size, +- info->var.bits_per_pixel); ++ info->var.bits_per_pixel, value); ++ ++ /* Need to set the display number to act on first ++ * Cannot do it in the tag list because on older firmware the call ++ * will fail and stop the rest of the list being executed. ++ * We can ignore this call failing as the default at other end is 0 ++ */ ++ set_display_num(fb); + + /* Try allocating our own buffer. We can specify all the parameters */ + image_size = ((info->var.xres * info->var.yres) * + info->var.bits_per_pixel) >> 3; + +- if (!fb->disable_arm_alloc && ++ if (!fb->fbdev->disable_arm_alloc && + (image_size != fb->image_size || !fb->dma_addr)) { + if (fb->dma_addr) { + dma_free_coherent(info->device, fb->image_size, +@@ -306,7 +402,7 @@ static int bcm2708_fb_set_par(struct fb_ + + if (!fb->cpuaddr) { + fb->dma_addr = 0; +- fb->disable_arm_alloc = true; ++ fb->fbdev->disable_arm_alloc = true; + } else { + fb->image_size = image_size; + } +@@ -317,7 +413,7 @@ static int bcm2708_fb_set_par(struct fb_ + fbinfo.screen_size = image_size; + fbinfo.pitch = (info->var.xres * info->var.bits_per_pixel) >> 3; + +- ret = rpi_firmware_property_list(fb->fw, &fbinfo, ++ ret = rpi_firmware_property_list(fb->fbdev->fw, &fbinfo, + sizeof(fbinfo)); + if (ret || fbinfo.base != fb->dma_addr) { + /* Firmware either failed, or assigned a different base +@@ -330,7 +426,7 @@ static int bcm2708_fb_set_par(struct fb_ + fb->image_size = 0; + fb->cpuaddr = NULL; + fb->dma_addr = 0; +- fb->disable_arm_alloc = true; ++ fb->fbdev->disable_arm_alloc = true; + } + } else { + /* Our allocation failed - drop into the old scheme of +@@ -349,7 +445,7 @@ static int bcm2708_fb_set_par(struct fb_ + fbinfo.tag6.tag = RPI_FIRMWARE_FRAMEBUFFER_GET_PITCH; + fbinfo.pitch = 0; + +- ret = rpi_firmware_property_list(fb->fw, &fbinfo, ++ ret = rpi_firmware_property_list(fb->fbdev->fw, &fbinfo, + sizeof(fbinfo)); + if (ret) { + dev_err(info->device, +@@ -439,7 +535,10 @@ static int bcm2708_fb_setcolreg(unsigned + packet->length = regno + 1; + memcpy(packet->cmap, fb->gpu_cmap, + sizeof(packet->cmap)); +- ret = rpi_firmware_property(fb->fw, ++ ++ set_display_num(fb); ++ ++ ret = rpi_firmware_property(fb->fbdev->fw, + RPI_FIRMWARE_FRAMEBUFFER_SET_PALETTE, + packet, + (2 + packet->length) * sizeof(u32)); +@@ -478,8 +577,11 @@ static int bcm2708_fb_blank(int blank_mo + return -EINVAL; + } + +- ret = rpi_firmware_property(fb->fw, RPI_FIRMWARE_FRAMEBUFFER_BLANK, ++ set_display_num(fb); ++ ++ ret = rpi_firmware_property(fb->fbdev->fw, RPI_FIRMWARE_FRAMEBUFFER_BLANK, + &value, sizeof(value)); ++ + if (ret) + dev_err(info->device, "%s(%d) failed: %d\n", __func__, + blank_mode, ret); +@@ -496,12 +598,14 @@ static int bcm2708_fb_pan_display(struct + info->var.yoffset = var->yoffset; + result = bcm2708_fb_set_par(info); + if (result != 0) +- pr_err("%s(%d,%d) returns=%d\n", __func__, var->xoffset, ++ pr_err("%s(%u,%u) returns=%d\n", __func__, var->xoffset, + var->yoffset, result); + return result; + } + + static int bcm2708_ioctl(struct fb_info *info, unsigned int cmd, unsigned long arg) ++static int bcm2708_ioctl(struct fb_info *info, unsigned int cmd, ++ unsigned long arg) + { + struct bcm2708_fb *fb = to_bcm2708(info); + u32 dummy = 0; +@@ -509,7 +613,9 @@ static int bcm2708_ioctl(struct fb_info + + switch (cmd) { + case FBIO_WAITFORVSYNC: +- ret = rpi_firmware_property(fb->fw, ++ set_display_num(fb); ++ ++ ret = rpi_firmware_property(fb->fbdev->fw, + RPI_FIRMWARE_FRAMEBUFFER_SET_VSYNC, + &dummy, sizeof(dummy)); + break; +@@ -526,23 +632,22 @@ static int bcm2708_ioctl(struct fb_info + static void bcm2708_fb_fillrect(struct fb_info *info, + const struct fb_fillrect *rect) + { +- /* (is called) print_debug("bcm2708_fb_fillrect\n"); */ + cfb_fillrect(info, rect); + } + + /* A helper function for configuring dma control block */ + static void set_dma_cb(struct bcm2708_dma_cb *cb, +- int burst_size, +- dma_addr_t dst, +- int dst_stride, +- dma_addr_t src, +- int src_stride, +- int w, +- int h) ++ int burst_size, ++ dma_addr_t dst, ++ int dst_stride, ++ dma_addr_t src, ++ int src_stride, ++ int w, ++ int h) + { + cb->info = BCM2708_DMA_BURST(burst_size) | BCM2708_DMA_S_WIDTH | +- BCM2708_DMA_S_INC | BCM2708_DMA_D_WIDTH | +- BCM2708_DMA_D_INC | BCM2708_DMA_TDMODE; ++ BCM2708_DMA_S_INC | BCM2708_DMA_D_WIDTH | ++ BCM2708_DMA_D_INC | BCM2708_DMA_TDMODE; + cb->dst = dst; + cb->src = src; + /* +@@ -560,15 +665,19 @@ static void bcm2708_fb_copyarea(struct f + const struct fb_copyarea *region) + { + struct bcm2708_fb *fb = to_bcm2708(info); +- struct bcm2708_dma_cb *cb = fb->cb_base; ++ struct bcm2708_fb_dev *fbdev = fb->fbdev; ++ struct bcm2708_dma_cb *cb = fbdev->cb_base; + int bytes_per_pixel = (info->var.bits_per_pixel + 7) >> 3; + + /* Channel 0 supports larger bursts and is a bit faster */ +- int burst_size = (fb->dma_chan == 0) ? 8 : 2; ++ int burst_size = (fbdev->dma_chan == 0) ? 8 : 2; + int pixels = region->width * region->height; + +- /* Fallback to cfb_copyarea() if we don't like something */ +- if (bytes_per_pixel > 4 || ++ /* If DMA is currently in use (ie being used on another FB), then ++ * rather than wait for it to finish, just use the cfb_copyarea ++ */ ++ if (!mutex_trylock(&fbdev->dma_mutex) || ++ bytes_per_pixel > 4 || + info->var.xres * info->var.yres > 1920 * 1200 || + region->width <= 0 || region->width > info->var.xres || + region->height <= 0 || region->height > info->var.yres || +@@ -595,8 +704,8 @@ static void bcm2708_fb_copyarea(struct f + * 1920x1200 resolution at 32bpp pixel depth. + */ + int y; +- dma_addr_t control_block_pa = fb->cb_handle; +- dma_addr_t scratchbuf = fb->cb_handle + 16 * 1024; ++ dma_addr_t control_block_pa = fbdev->cb_handle; ++ dma_addr_t scratchbuf = fbdev->cb_handle + 16 * 1024; + int scanline_size = bytes_per_pixel * region->width; + int scanlines_per_cb = (64 * 1024 - 16 * 1024) / scanline_size; + +@@ -646,10 +755,10 @@ static void bcm2708_fb_copyarea(struct f + } + set_dma_cb(cb, burst_size, + fb->fb_bus_address + dy * fb->fb.fix.line_length + +- bytes_per_pixel * region->dx, ++ bytes_per_pixel * region->dx, + stride, + fb->fb_bus_address + sy * fb->fb.fix.line_length + +- bytes_per_pixel * region->sx, ++ bytes_per_pixel * region->sx, + stride, + region->width * bytes_per_pixel, + region->height); +@@ -659,32 +768,33 @@ static void bcm2708_fb_copyarea(struct f + cb->next = 0; + + if (pixels < dma_busy_wait_threshold) { +- bcm_dma_start(fb->dma_chan_base, fb->cb_handle); +- bcm_dma_wait_idle(fb->dma_chan_base); ++ bcm_dma_start(fbdev->dma_chan_base, fbdev->cb_handle); ++ bcm_dma_wait_idle(fbdev->dma_chan_base); + } else { +- void __iomem *dma_chan = fb->dma_chan_base; ++ void __iomem *local_dma_chan = fbdev->dma_chan_base; + + cb->info |= BCM2708_DMA_INT_EN; +- bcm_dma_start(fb->dma_chan_base, fb->cb_handle); +- while (bcm_dma_is_busy(dma_chan)) { +- wait_event_interruptible(fb->dma_waitq, +- !bcm_dma_is_busy(dma_chan)); ++ bcm_dma_start(fbdev->dma_chan_base, fbdev->cb_handle); ++ while (bcm_dma_is_busy(local_dma_chan)) { ++ wait_event_interruptible(fbdev->dma_waitq, ++ !bcm_dma_is_busy(local_dma_chan)); + } +- fb->stats.dma_irqs++; ++ fbdev->dma_stats.dma_irqs++; + } +- fb->stats.dma_copies++; ++ fbdev->dma_stats.dma_copies++; ++ ++ mutex_unlock(&fbdev->dma_mutex); + } + + static void bcm2708_fb_imageblit(struct fb_info *info, + const struct fb_image *image) + { +- /* (is called) print_debug("bcm2708_fb_imageblit\n"); */ + cfb_imageblit(info, image); + } + + static irqreturn_t bcm2708_fb_dma_irq(int irq, void *cxt) + { +- struct bcm2708_fb *fb = cxt; ++ struct bcm2708_fb_dev *fbdev = cxt; + + /* FIXME: should read status register to check if this is + * actually interrupting us or not, in case this interrupt +@@ -694,9 +804,9 @@ static irqreturn_t bcm2708_fb_dma_irq(in + */ + + /* acknowledge the interrupt */ +- writel(BCM2708_DMA_INT, fb->dma_chan_base + BCM2708_DMA_CS); ++ writel(BCM2708_DMA_INT, fbdev->dma_chan_base + BCM2708_DMA_CS); + +- wake_up(&fb->dma_waitq); ++ wake_up(&fbdev->dma_waitq); + return IRQ_HANDLED; + } + +@@ -729,11 +839,23 @@ static int bcm2708_fb_register(struct bc + fb->fb.fix.ywrapstep = 0; + fb->fb.fix.accel = FB_ACCEL_NONE; + +- fb->fb.var.xres = fbwidth; +- fb->fb.var.yres = fbheight; +- fb->fb.var.xres_virtual = fbwidth; +- fb->fb.var.yres_virtual = fbheight; +- fb->fb.var.bits_per_pixel = fbdepth; ++ /* If we have data from the VC4 on FB's, use that, otherwise use the ++ * module parameters ++ */ ++ if (fb->display_settings.width) { ++ fb->fb.var.xres = fb->display_settings.width; ++ fb->fb.var.yres = fb->display_settings.height; ++ fb->fb.var.xres_virtual = fb->fb.var.xres; ++ fb->fb.var.yres_virtual = fb->fb.var.yres; ++ fb->fb.var.bits_per_pixel = fb->display_settings.depth; ++ } else { ++ fb->fb.var.xres = fbwidth; ++ fb->fb.var.yres = fbheight; ++ fb->fb.var.xres_virtual = fbwidth; ++ fb->fb.var.yres_virtual = fbheight; ++ fb->fb.var.bits_per_pixel = fbdepth; ++ } ++ + fb->fb.var.vmode = FB_VMODE_NONINTERLACED; + fb->fb.var.activate = FB_ACTIVATE_NOW; + fb->fb.var.nonstd = 0; +@@ -749,26 +871,23 @@ static int bcm2708_fb_register(struct bc + fb->fb.monspecs.dclkmax = 100000000; + + bcm2708_fb_set_bitfields(&fb->fb.var); +- init_waitqueue_head(&fb->dma_waitq); + + /* + * Allocate colourmap. + */ +- + fb_set_var(&fb->fb, &fb->fb.var); ++ + ret = bcm2708_fb_set_par(&fb->fb); ++ + if (ret) + return ret; + +- print_debug("BCM2708FB: registering framebuffer (%dx%d@%d) (%d)\n", +- fbwidth, fbheight, fbdepth, fbswap); +- + ret = register_framebuffer(&fb->fb); +- print_debug("BCM2708FB: register framebuffer (%d)\n", ret); ++ + if (ret == 0) + goto out; + +- print_debug("BCM2708FB: cannot register framebuffer (%d)\n", ret); ++ dev_warn(fb->fb.dev, "Unable to register framebuffer (%d)\n", ret); + out: + return ret; + } +@@ -777,10 +896,18 @@ static int bcm2708_fb_probe(struct platf + { + struct device_node *fw_np; + struct rpi_firmware *fw; +- struct bcm2708_fb *fb; +- int ret; ++ int ret, i; ++ u32 num_displays; ++ struct bcm2708_fb_dev *fbdev; ++ struct { u32 base, length; } gpu_mem; ++ ++ fbdev = devm_kzalloc(&dev->dev, sizeof(*fbdev), GFP_KERNEL); ++ ++ if (!fbdev) ++ return -ENOMEM; + + fw_np = of_parse_phandle(dev->dev.of_node, "firmware", 0); ++ + /* Remove comment when booting without Device Tree is no longer supported + * if (!fw_np) { + * dev_err(&dev->dev, "Missing firmware node\n"); +@@ -788,90 +915,154 @@ static int bcm2708_fb_probe(struct platf + * } + */ + fw = rpi_firmware_get(fw_np); ++ fbdev->fw = fw; ++ + if (!fw) + return -EPROBE_DEFER; + +- fb = kzalloc(sizeof(*fb), GFP_KERNEL); +- if (!fb) { +- ret = -ENOMEM; +- goto free_region; ++ ret = rpi_firmware_property(fw, ++ RPI_FIRMWARE_FRAMEBUFFER_GET_NUM_DISPLAYS, ++ &num_displays, sizeof(u32)); ++ ++ /* If we fail to get the number of displays, or it returns 0, then ++ * assume old firmware that doesn't have the mailbox call, so just ++ * set one display ++ */ ++ if (ret || num_displays == 0) { ++ num_displays = 1; ++ dev_err(&dev->dev, ++ "Unable to determine number of FB's. Assuming 1\n"); ++ ret = 0; ++ } else { ++ fbdev->firmware_supports_multifb = 1; ++ } ++ ++ if (num_displays > MAX_FRAMEBUFFERS) { ++ dev_warn(&dev->dev, ++ "More displays reported from firmware than supported in driver (%u vs %u)", ++ num_displays, MAX_FRAMEBUFFERS); ++ num_displays = MAX_FRAMEBUFFERS; + } + +- fb->fw = fw; +- bcm2708_fb_debugfs_init(fb); ++ dev_info(&dev->dev, "FB found %d display(s)\n", num_displays); ++ ++ /* Set up the DMA information. Note we have just one set of DMA ++ * parameters to work with all the FB's so requires synchronising when ++ * being used ++ */ ++ ++ mutex_init(&fbdev->dma_mutex); + +- fb->cb_base = dma_alloc_wc(&dev->dev, SZ_64K, +- &fb->cb_handle, GFP_KERNEL); +- if (!fb->cb_base) { ++ fbdev->cb_base = dma_alloc_wc(&dev->dev, SZ_64K, ++ &fbdev->cb_handle, ++ GFP_KERNEL); ++ if (!fbdev->cb_base) { + dev_err(&dev->dev, "cannot allocate DMA CBs\n"); + ret = -ENOMEM; + goto free_fb; + } + +- pr_info("BCM2708FB: allocated DMA memory %pad\n", &fb->cb_handle); +- + ret = bcm_dma_chan_alloc(BCM_DMA_FEATURE_BULK, +- &fb->dma_chan_base, &fb->dma_irq); ++ &fbdev->dma_chan_base, ++ &fbdev->dma_irq); + if (ret < 0) { +- dev_err(&dev->dev, "couldn't allocate a DMA channel\n"); ++ dev_err(&dev->dev, "Couldn't allocate a DMA channel\n"); + goto free_cb; + } +- fb->dma_chan = ret; ++ fbdev->dma_chan = ret; + +- ret = request_irq(fb->dma_irq, bcm2708_fb_dma_irq, +- 0, "bcm2708_fb dma", fb); ++ ret = request_irq(fbdev->dma_irq, bcm2708_fb_dma_irq, ++ 0, "bcm2708_fb DMA", fbdev); + if (ret) { +- pr_err("%s: failed to request DMA irq\n", __func__); ++ dev_err(&dev->dev, ++ "Failed to request DMA irq\n"); + goto free_dma_chan; + } + +- pr_info("BCM2708FB: allocated DMA channel %d\n", fb->dma_chan); ++ rpi_firmware_property(fbdev->fw, ++ RPI_FIRMWARE_GET_VC_MEMORY, ++ &gpu_mem, sizeof(gpu_mem)); ++ ++ for (i = 0; i < num_displays; i++) { ++ struct bcm2708_fb *fb = &fbdev->displays[i]; ++ ++ fb->display_settings.display_num = i; ++ fb->dev = dev; ++ fb->fb.device = &dev->dev; ++ fb->fbdev = fbdev; ++ ++ fb->gpu.base = gpu_mem.base; ++ fb->gpu.length = gpu_mem.length; ++ ++ if (fbdev->firmware_supports_multifb) { ++ ret = rpi_firmware_property(fw, ++ RPI_FIRMWARE_FRAMEBUFFER_GET_DISPLAY_SETTINGS, ++ &fb->display_settings, ++ GET_DISPLAY_SETTINGS_PAYLOAD_SIZE); ++ } else { ++ memset(&fb->display_settings, 0, ++ sizeof(fb->display_settings)); ++ } + +- fb->dev = dev; +- fb->fb.device = &dev->dev; ++ ret = bcm2708_fb_register(fb); + +- /* failure here isn't fatal, but we'll fail in vc_mem_copy if +- * fb->gpu is not valid +- */ +- rpi_firmware_property(fb->fw, RPI_FIRMWARE_GET_VC_MEMORY, &fb->gpu, +- sizeof(fb->gpu)); ++ if (ret == 0) { ++ bcm2708_fb_debugfs_init(fb); + +- ret = bcm2708_fb_register(fb); +- if (ret == 0) { +- platform_set_drvdata(dev, fb); +- goto out; ++ fbdev->num_displays++; ++ ++ dev_info(&dev->dev, ++ "Registered framebuffer for display %u, size %ux%u\n", ++ fb->display_settings.display_num, ++ fb->fb.var.xres, ++ fb->fb.var.yres); ++ } else { ++ // Use this to flag if this FB entry is in use. ++ fb->fbdev = NULL; ++ } ++ } ++ ++ // Did we actually successfully create any FB's? ++ if (fbdev->num_displays) { ++ init_waitqueue_head(&fbdev->dma_waitq); ++ platform_set_drvdata(dev, fbdev); ++ return ret; + } + + free_dma_chan: +- bcm_dma_chan_free(fb->dma_chan); ++ bcm_dma_chan_free(fbdev->dma_chan); + free_cb: +- dma_free_wc(&dev->dev, SZ_64K, fb->cb_base, fb->cb_handle); ++ dma_free_wc(&dev->dev, SZ_64K, fbdev->cb_base, ++ fbdev->cb_handle); + free_fb: +- kfree(fb); +-free_region: + dev_err(&dev->dev, "probe failed, err %d\n", ret); +-out: ++ + return ret; + } + + static int bcm2708_fb_remove(struct platform_device *dev) + { +- struct bcm2708_fb *fb = platform_get_drvdata(dev); ++ struct bcm2708_fb_dev *fbdev = platform_get_drvdata(dev); ++ int i; + + platform_set_drvdata(dev, NULL); + +- if (fb->fb.screen_base) +- iounmap(fb->fb.screen_base); +- unregister_framebuffer(&fb->fb); +- +- dma_free_wc(&dev->dev, SZ_64K, fb->cb_base, fb->cb_handle); +- bcm_dma_chan_free(fb->dma_chan); +- +- bcm2708_fb_debugfs_deinit(fb); ++ for (i = 0; i < fbdev->num_displays; i++) { ++ if (fbdev->displays[i].fb.screen_base) ++ iounmap(fbdev->displays[i].fb.screen_base); ++ ++ if (fbdev->displays[i].fbdev) { ++ unregister_framebuffer(&fbdev->displays[i].fb); ++ bcm2708_fb_debugfs_deinit(&fbdev->displays[i]); ++ } ++ } + +- free_irq(fb->dma_irq, fb); ++ dma_free_wc(&dev->dev, SZ_64K, fbdev->cb_base, ++ fbdev->cb_handle); ++ bcm_dma_chan_free(fbdev->dma_chan); ++ free_irq(fbdev->dma_irq, fbdev); + +- kfree(fb); ++ mutex_destroy(&fbdev->dma_mutex); + + return 0; + } +@@ -886,10 +1077,10 @@ static struct platform_driver bcm2708_fb + .probe = bcm2708_fb_probe, + .remove = bcm2708_fb_remove, + .driver = { +- .name = DRIVER_NAME, +- .owner = THIS_MODULE, +- .of_match_table = bcm2708_fb_of_match_table, +- }, ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ .of_match_table = bcm2708_fb_of_match_table, ++ }, + }; + + static int __init bcm2708_fb_init(void) +--- a/include/soc/bcm2835/raspberrypi-firmware.h ++++ b/include/soc/bcm2835/raspberrypi-firmware.h +@@ -106,9 +106,15 @@ enum rpi_firmware_property_tag { + RPI_FIRMWARE_FRAMEBUFFER_GET_VIRTUAL_OFFSET = 0x00040009, + RPI_FIRMWARE_FRAMEBUFFER_GET_OVERSCAN = 0x0004000a, + RPI_FIRMWARE_FRAMEBUFFER_GET_PALETTE = 0x0004000b, ++ RPI_FIRMWARE_FRAMEBUFFER_GET_LAYER = 0x0004000c, ++ RPI_FIRMWARE_FRAMEBUFFER_GET_TRANSFORM = 0x0004000d, ++ RPI_FIRMWARE_FRAMEBUFFER_GET_VSYNC = 0x0004000e, + RPI_FIRMWARE_FRAMEBUFFER_GET_TOUCHBUF = 0x0004000f, + RPI_FIRMWARE_FRAMEBUFFER_GET_GPIOVIRTBUF = 0x00040010, + RPI_FIRMWARE_FRAMEBUFFER_RELEASE = 0x00048001, ++ RPI_FIRMWARE_FRAMEBUFFER_SET_DISPLAY_NUM = 0x00048013, ++ RPI_FIRMWARE_FRAMEBUFFER_GET_NUM_DISPLAYS = 0x00040013, ++ RPI_FIRMWARE_FRAMEBUFFER_GET_DISPLAY_SETTINGS = 0x00040014, + RPI_FIRMWARE_FRAMEBUFFER_TEST_PHYSICAL_WIDTH_HEIGHT = 0x00044003, + RPI_FIRMWARE_FRAMEBUFFER_TEST_VIRTUAL_WIDTH_HEIGHT = 0x00044004, + RPI_FIRMWARE_FRAMEBUFFER_TEST_DEPTH = 0x00044005, +@@ -117,6 +123,8 @@ enum rpi_firmware_property_tag { + RPI_FIRMWARE_FRAMEBUFFER_TEST_VIRTUAL_OFFSET = 0x00044009, + RPI_FIRMWARE_FRAMEBUFFER_TEST_OVERSCAN = 0x0004400a, + RPI_FIRMWARE_FRAMEBUFFER_TEST_PALETTE = 0x0004400b, ++ RPI_FIRMWARE_FRAMEBUFFER_TEST_LAYER = 0x0004400c, ++ RPI_FIRMWARE_FRAMEBUFFER_TEST_TRANSFORM = 0x0004400d, + RPI_FIRMWARE_FRAMEBUFFER_TEST_VSYNC = 0x0004400e, + RPI_FIRMWARE_FRAMEBUFFER_SET_PHYSICAL_WIDTH_HEIGHT = 0x00048003, + RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_WIDTH_HEIGHT = 0x00048004, +@@ -127,9 +135,12 @@ enum rpi_firmware_property_tag { + RPI_FIRMWARE_FRAMEBUFFER_SET_VIRTUAL_OFFSET = 0x00048009, + RPI_FIRMWARE_FRAMEBUFFER_SET_OVERSCAN = 0x0004800a, + RPI_FIRMWARE_FRAMEBUFFER_SET_PALETTE = 0x0004800b, ++ + RPI_FIRMWARE_FRAMEBUFFER_SET_TOUCHBUF = 0x0004801f, + RPI_FIRMWARE_FRAMEBUFFER_SET_GPIOVIRTBUF = 0x00048020, + RPI_FIRMWARE_FRAMEBUFFER_SET_VSYNC = 0x0004800e, ++ RPI_FIRMWARE_FRAMEBUFFER_SET_LAYER = 0x0004800c, ++ RPI_FIRMWARE_FRAMEBUFFER_SET_TRANSFORM = 0x0004800d, + RPI_FIRMWARE_FRAMEBUFFER_SET_BACKLIGHT = 0x0004800f, + + RPI_FIRMWARE_VCHIQ_INIT = 0x00048010, +@@ -138,6 +149,8 @@ enum rpi_firmware_property_tag { + RPI_FIRMWARE_GET_DMA_CHANNELS = 0x00060001, + }; + ++#define GET_DISPLAY_SETTINGS_PAYLOAD_SIZE 64 ++ + #if IS_ENABLED(CONFIG_RASPBERRYPI_FIRMWARE) + int rpi_firmware_property(struct rpi_firmware *fw, + u32 tag, void *data, size_t len); diff --git a/target/linux/bcm27xx/patches-5.10/950-0043-fbdev-add-FBIOCOPYAREA-ioctl.patch b/target/linux/bcm27xx/patches-5.10/950-0043-fbdev-add-FBIOCOPYAREA-ioctl.patch new file mode 100644 index 0000000000..75e3aea2d7 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0043-fbdev-add-FBIOCOPYAREA-ioctl.patch @@ -0,0 +1,337 @@ +From 6005247285065235845f233077bbeedb19a484c7 Mon Sep 17 00:00:00 2001 +From: Siarhei Siamashka +Date: Mon, 17 Jun 2013 13:32:11 +0300 +Subject: [PATCH] fbdev: add FBIOCOPYAREA ioctl + +Based on the patch authored by Ali Gholami Rudi at + https://lkml.org/lkml/2009/7/13/153 + +Provide an ioctl for userspace applications, but only if this operation +is hardware accelerated (otherwide it does not make any sense). + +Signed-off-by: Siarhei Siamashka + +bcm2708_fb: Add ioctl for reading gpu memory through dma + +video: bcm2708_fb: Add compat_ioctl support. + +When using a 64 bit kernel with 32 bit userspace we need +compat ioctl handling for FBIODMACOPY as one of the +parameters is a pointer. + +Signed-off-by: Dave Stevenson +--- + drivers/video/fbdev/bcm2708_fb.c | 170 ++++++++++++++++++++++++++++++- + drivers/video/fbdev/core/fbmem.c | 35 +++++++ + include/uapi/linux/fb.h | 12 +++ + 3 files changed, 213 insertions(+), 4 deletions(-) + +--- a/drivers/video/fbdev/bcm2708_fb.c ++++ b/drivers/video/fbdev/bcm2708_fb.c +@@ -32,8 +32,10 @@ + #include + #include + #include ++#include + #include + #include ++#include + #include + #include + +@@ -184,9 +186,6 @@ static int bcm2708_fb_debugfs_init(struc + + fb->debugfs_subdir = debugfs_create_dir(buf, fb->debugfs_dir); + +- debugfs_create_regset32("stats", 0444, fb->debugfs_dir, +- &fb->stats.regset); +- + if (!fb->debugfs_subdir) { + dev_warn(fb->fb.dev, "%s: could not create debugfs entry %u\n", + __func__, fb->display_settings.display_num); +@@ -603,7 +602,110 @@ static int bcm2708_fb_pan_display(struct + return result; + } + +-static int bcm2708_ioctl(struct fb_info *info, unsigned int cmd, unsigned long arg) ++static void dma_memcpy(struct bcm2708_fb *fb, dma_addr_t dst, dma_addr_t src, ++ int size) ++{ ++ struct bcm2708_fb_dev *fbdev = fb->fbdev; ++ struct bcm2708_dma_cb *cb = fbdev->cb_base; ++ int burst_size = (fbdev->dma_chan == 0) ? 8 : 2; ++ ++ cb->info = BCM2708_DMA_BURST(burst_size) | BCM2708_DMA_S_WIDTH | ++ BCM2708_DMA_S_INC | BCM2708_DMA_D_WIDTH | ++ BCM2708_DMA_D_INC; ++ cb->dst = dst; ++ cb->src = src; ++ cb->length = size; ++ cb->stride = 0; ++ cb->pad[0] = 0; ++ cb->pad[1] = 0; ++ cb->next = 0; ++ ++ // Not sure what to do if this gets a signal whilst waiting ++ if (mutex_lock_interruptible(&fbdev->dma_mutex)) ++ return; ++ ++ if (size < dma_busy_wait_threshold) { ++ bcm_dma_start(fbdev->dma_chan_base, fbdev->cb_handle); ++ bcm_dma_wait_idle(fbdev->dma_chan_base); ++ } else { ++ void __iomem *local_dma_chan = fbdev->dma_chan_base; ++ ++ cb->info |= BCM2708_DMA_INT_EN; ++ bcm_dma_start(fbdev->dma_chan_base, fbdev->cb_handle); ++ while (bcm_dma_is_busy(local_dma_chan)) { ++ wait_event_interruptible(fbdev->dma_waitq, ++ !bcm_dma_is_busy(local_dma_chan)); ++ } ++ fbdev->dma_stats.dma_irqs++; ++ } ++ fbdev->dma_stats.dma_copies++; ++ ++ mutex_unlock(&fbdev->dma_mutex); ++} ++ ++/* address with no aliases */ ++#define INTALIAS_NORMAL(x) ((x) & ~0xc0000000) ++/* cache coherent but non-allocating in L1 and L2 */ ++#define INTALIAS_L1L2_NONALLOCATING(x) (((x) & ~0xc0000000) | 0x80000000) ++ ++static long vc_mem_copy(struct bcm2708_fb *fb, struct fb_dmacopy *ioparam) ++{ ++ size_t size = PAGE_SIZE; ++ u32 *buf = NULL; ++ dma_addr_t bus_addr; ++ long rc = 0; ++ size_t offset; ++ ++ /* restrict this to root user */ ++ if (!uid_eq(current_euid(), GLOBAL_ROOT_UID)) { ++ rc = -EFAULT; ++ goto out; ++ } ++ ++ if (!fb->gpu.base || !fb->gpu.length) { ++ pr_err("[%s]: Unable to determine gpu memory (%x,%x)\n", ++ __func__, fb->gpu.base, fb->gpu.length); ++ return -EFAULT; ++ } ++ ++ if (INTALIAS_NORMAL(ioparam->src) < fb->gpu.base || ++ INTALIAS_NORMAL(ioparam->src) >= fb->gpu.base + fb->gpu.length) { ++ pr_err("[%s]: Invalid memory access %x (%x-%x)", __func__, ++ INTALIAS_NORMAL(ioparam->src), fb->gpu.base, ++ fb->gpu.base + fb->gpu.length); ++ return -EFAULT; ++ } ++ ++ buf = dma_alloc_coherent(fb->fb.device, PAGE_ALIGN(size), &bus_addr, ++ GFP_ATOMIC); ++ if (!buf) { ++ pr_err("[%s]: failed to dma_alloc_coherent(%zd)\n", __func__, ++ size); ++ rc = -ENOMEM; ++ goto out; ++ } ++ ++ for (offset = 0; offset < ioparam->length; offset += size) { ++ size_t remaining = ioparam->length - offset; ++ size_t s = min(size, remaining); ++ u8 *p = (u8 *)((uintptr_t)ioparam->src + offset); ++ u8 *q = (u8 *)ioparam->dst + offset; ++ ++ dma_memcpy(fb, bus_addr, ++ INTALIAS_L1L2_NONALLOCATING((dma_addr_t)p), size); ++ if (copy_to_user(q, buf, s) != 0) { ++ pr_err("[%s]: failed to copy-to-user\n", __func__); ++ rc = -EFAULT; ++ goto out; ++ } ++ } ++out: ++ if (buf) ++ dma_free_coherent(fb->fb.device, PAGE_ALIGN(size), buf, ++ bus_addr); ++ return rc; ++} ++ + static int bcm2708_ioctl(struct fb_info *info, unsigned int cmd, + unsigned long arg) + { +@@ -619,6 +721,21 @@ static int bcm2708_ioctl(struct fb_info + RPI_FIRMWARE_FRAMEBUFFER_SET_VSYNC, + &dummy, sizeof(dummy)); + break; ++ ++ case FBIODMACOPY: ++ { ++ struct fb_dmacopy ioparam; ++ /* Get the parameter data. ++ */ ++ if (copy_from_user ++ (&ioparam, (void *)arg, sizeof(ioparam))) { ++ pr_err("[%s]: failed to copy-from-user\n", __func__); ++ ret = -EFAULT; ++ break; ++ } ++ ret = vc_mem_copy(fb, &ioparam); ++ break; ++ } + default: + dev_dbg(info->device, "Unknown ioctl 0x%x\n", cmd); + return -ENOTTY; +@@ -629,6 +746,48 @@ static int bcm2708_ioctl(struct fb_info + + return ret; + } ++ ++#ifdef CONFIG_COMPAT ++struct fb_dmacopy32 { ++ compat_uptr_t dst; ++ __u32 src; ++ __u32 length; ++}; ++ ++#define FBIODMACOPY32 _IOW('z', 0x22, struct fb_dmacopy32) ++ ++static int bcm2708_compat_ioctl(struct fb_info *info, unsigned int cmd, ++ unsigned long arg) ++{ ++ struct bcm2708_fb *fb = to_bcm2708(info); ++ int ret; ++ ++ switch (cmd) { ++ case FBIODMACOPY32: ++ { ++ struct fb_dmacopy32 param32; ++ struct fb_dmacopy param; ++ /* Get the parameter data. ++ */ ++ if (copy_from_user(¶m32, (void *)arg, sizeof(param32))) { ++ pr_err("[%s]: failed to copy-from-user\n", __func__); ++ ret = -EFAULT; ++ break; ++ } ++ param.dst = compat_ptr(param32.dst); ++ param.src = param32.src; ++ param.length = param32.length; ++ ret = vc_mem_copy(fb, ¶m); ++ break; ++ } ++ default: ++ ret = bcm2708_ioctl(info, cmd, arg); ++ break; ++ } ++ return ret; ++} ++#endif ++ + static void bcm2708_fb_fillrect(struct fb_info *info, + const struct fb_fillrect *rect) + { +@@ -821,6 +980,9 @@ static struct fb_ops bcm2708_fb_ops = { + .fb_imageblit = bcm2708_fb_imageblit, + .fb_pan_display = bcm2708_fb_pan_display, + .fb_ioctl = bcm2708_ioctl, ++#ifdef CONFIG_COMPAT ++ .fb_compat_ioctl = bcm2708_compat_ioctl, ++#endif + }; + + static int bcm2708_fb_register(struct bcm2708_fb *fb) +--- a/drivers/video/fbdev/core/fbmem.c ++++ b/drivers/video/fbdev/core/fbmem.c +@@ -1079,6 +1079,30 @@ fb_blank(struct fb_info *info, int blank + } + EXPORT_SYMBOL(fb_blank); + ++static int fb_copyarea_user(struct fb_info *info, ++ struct fb_copyarea *copy) ++{ ++ int ret = 0; ++ lock_fb_info(info); ++ if (copy->dx >= info->var.xres || ++ copy->sx >= info->var.xres || ++ copy->width > info->var.xres || ++ copy->dy >= info->var.yres || ++ copy->sy >= info->var.yres || ++ copy->height > info->var.yres || ++ copy->dx + copy->width > info->var.xres || ++ copy->sx + copy->width > info->var.xres || ++ copy->dy + copy->height > info->var.yres || ++ copy->sy + copy->height > info->var.yres) { ++ ret = -EINVAL; ++ goto out; ++ } ++ info->fbops->fb_copyarea(info, copy); ++out: ++ unlock_fb_info(info); ++ return ret; ++} ++ + static long do_fb_ioctl(struct fb_info *info, unsigned int cmd, + unsigned long arg) + { +@@ -1087,6 +1111,7 @@ static long do_fb_ioctl(struct fb_info * + struct fb_fix_screeninfo fix; + struct fb_cmap cmap_from; + struct fb_cmap_user cmap; ++ struct fb_copyarea copy; + void __user *argp = (void __user *)arg; + long ret = 0; + +@@ -1162,6 +1187,15 @@ static long do_fb_ioctl(struct fb_info * + unlock_fb_info(info); + console_unlock(); + break; ++ case FBIOCOPYAREA: ++ if (info->flags & FBINFO_HWACCEL_COPYAREA) { ++ /* only provide this ioctl if it is accelerated */ ++ if (copy_from_user(©, argp, sizeof(copy))) ++ return -EFAULT; ++ ret = fb_copyarea_user(info, ©); ++ break; ++ } ++ /* fall through */ + default: + lock_fb_info(info); + fb = info->fbops; +@@ -1307,6 +1341,7 @@ static long fb_compat_ioctl(struct file + case FBIOPAN_DISPLAY: + case FBIOGET_CON2FBMAP: + case FBIOPUT_CON2FBMAP: ++ case FBIOCOPYAREA: + arg = (unsigned long) compat_ptr(arg); + fallthrough; + case FBIOBLANK: +--- a/include/uapi/linux/fb.h ++++ b/include/uapi/linux/fb.h +@@ -35,6 +35,12 @@ + #define FBIOPUT_MODEINFO 0x4617 + #define FBIOGET_DISPINFO 0x4618 + #define FBIO_WAITFORVSYNC _IOW('F', 0x20, __u32) ++/* ++ * HACK: use 'z' in order not to clash with any other ioctl numbers which might ++ * be concurrently added to the mainline kernel ++ */ ++#define FBIOCOPYAREA _IOW('z', 0x21, struct fb_copyarea) ++#define FBIODMACOPY _IOW('z', 0x22, struct fb_dmacopy) + + #define FB_TYPE_PACKED_PIXELS 0 /* Packed Pixels */ + #define FB_TYPE_PLANES 1 /* Non interleaved planes */ +@@ -348,6 +354,12 @@ struct fb_copyarea { + __u32 sy; + }; + ++struct fb_dmacopy { ++ void *dst; ++ __u32 src; ++ __u32 length; ++}; ++ + struct fb_fillrect { + __u32 dx; /* screen-relative */ + __u32 dy; diff --git a/target/linux/bcm27xx/patches-5.10/950-0044-Speed-up-console-framebuffer-imageblit-function.patch b/target/linux/bcm27xx/patches-5.10/950-0044-Speed-up-console-framebuffer-imageblit-function.patch new file mode 100644 index 0000000000..f46a793d1d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0044-Speed-up-console-framebuffer-imageblit-function.patch @@ -0,0 +1,209 @@ +From cac14f80f1e41f9a977c3cd84b0b3b73740818f8 Mon Sep 17 00:00:00 2001 +From: Harm Hanemaaijer +Date: Thu, 20 Jun 2013 20:21:39 +0200 +Subject: [PATCH] Speed up console framebuffer imageblit function + +Especially on platforms with a slower CPU but a relatively high +framebuffer fill bandwidth, like current ARM devices, the existing +console monochrome imageblit function used to draw console text is +suboptimal for common pixel depths such as 16bpp and 32bpp. The existing +code is quite general and can deal with several pixel depths. By creating +special case functions for 16bpp and 32bpp, by far the most common pixel +formats used on modern systems, a significant speed-up is attained +which can be readily felt on ARM-based devices like the Raspberry Pi +and the Allwinner platform, but should help any platform using the +fb layer. + +The special case functions allow constant folding, eliminating a number +of instructions including divide operations, and allow the use of an +unrolled loop, eliminating instructions with a variable shift size, +reducing source memory access instructions, and eliminating excessive +branching. These unrolled loops also allow much better code optimization +by the C compiler. The code that selects which optimized variant is used +is also simplified, eliminating integer divide instructions. + +The speed-up, measured by timing 'cat file.txt' in the console, varies +between 40% and 70%, when testing on the Raspberry Pi and Allwinner +ARM-based platforms, depending on font size and the pixel depth, with +the greater benefit for 32bpp. + +Signed-off-by: Harm Hanemaaijer +--- + drivers/video/fbdev/core/cfbimgblt.c | 152 ++++++++++++++++++++++++++- + 1 file changed, 147 insertions(+), 5 deletions(-) + +--- a/drivers/video/fbdev/core/cfbimgblt.c ++++ b/drivers/video/fbdev/core/cfbimgblt.c +@@ -28,6 +28,11 @@ + * + * Also need to add code to deal with cards endians that are different than + * the native cpu endians. I also need to deal with MSB position in the word. ++ * Modified by Harm Hanemaaijer (fgenfb@yahoo.com) 2013: ++ * - Provide optimized versions of fast_imageblit for 16 and 32bpp that are ++ * significantly faster than the previous implementation. ++ * - Simplify the fast/slow_imageblit selection code, avoiding integer ++ * divides. + */ + #include + #include +@@ -262,6 +267,133 @@ static inline void fast_imageblit(const + } + } + ++/* ++ * Optimized fast_imageblit for bpp == 16. ppw = 2, bit_mask = 3 folded ++ * into the code, main loop unrolled. ++ */ ++ ++static inline void fast_imageblit16(const struct fb_image *image, ++ struct fb_info *p, u8 __iomem * dst1, ++ u32 fgcolor, u32 bgcolor) ++{ ++ u32 fgx = fgcolor, bgx = bgcolor; ++ u32 spitch = (image->width + 7) / 8; ++ u32 end_mask, eorx; ++ const char *s = image->data, *src; ++ u32 __iomem *dst; ++ const u32 *tab = NULL; ++ int i, j, k; ++ ++ tab = fb_be_math(p) ? cfb_tab16_be : cfb_tab16_le; ++ ++ fgx <<= 16; ++ bgx <<= 16; ++ fgx |= fgcolor; ++ bgx |= bgcolor; ++ ++ eorx = fgx ^ bgx; ++ k = image->width / 2; ++ ++ for (i = image->height; i--;) { ++ dst = (u32 __iomem *) dst1; ++ src = s; ++ ++ j = k; ++ while (j >= 4) { ++ u8 bits = *src; ++ end_mask = tab[(bits >> 6) & 3]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ end_mask = tab[(bits >> 4) & 3]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ end_mask = tab[(bits >> 2) & 3]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ end_mask = tab[bits & 3]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ src++; ++ j -= 4; ++ } ++ if (j != 0) { ++ u8 bits = *src; ++ end_mask = tab[(bits >> 6) & 3]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ if (j >= 2) { ++ end_mask = tab[(bits >> 4) & 3]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ if (j == 3) { ++ end_mask = tab[(bits >> 2) & 3]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst); ++ } ++ } ++ } ++ dst1 += p->fix.line_length; ++ s += spitch; ++ } ++} ++ ++/* ++ * Optimized fast_imageblit for bpp == 32. ppw = 1, bit_mask = 1 folded ++ * into the code, main loop unrolled. ++ */ ++ ++static inline void fast_imageblit32(const struct fb_image *image, ++ struct fb_info *p, u8 __iomem * dst1, ++ u32 fgcolor, u32 bgcolor) ++{ ++ u32 fgx = fgcolor, bgx = bgcolor; ++ u32 spitch = (image->width + 7) / 8; ++ u32 end_mask, eorx; ++ const char *s = image->data, *src; ++ u32 __iomem *dst; ++ const u32 *tab = NULL; ++ int i, j, k; ++ ++ tab = cfb_tab32; ++ ++ eorx = fgx ^ bgx; ++ k = image->width; ++ ++ for (i = image->height; i--;) { ++ dst = (u32 __iomem *) dst1; ++ src = s; ++ ++ j = k; ++ while (j >= 8) { ++ u8 bits = *src; ++ end_mask = tab[(bits >> 7) & 1]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ end_mask = tab[(bits >> 6) & 1]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ end_mask = tab[(bits >> 5) & 1]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ end_mask = tab[(bits >> 4) & 1]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ end_mask = tab[(bits >> 3) & 1]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ end_mask = tab[(bits >> 2) & 1]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ end_mask = tab[(bits >> 1) & 1]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ end_mask = tab[bits & 1]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ src++; ++ j -= 8; ++ } ++ if (j != 0) { ++ u32 bits = (u32) * src; ++ while (j > 1) { ++ end_mask = tab[(bits >> 7) & 1]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst++); ++ bits <<= 1; ++ j--; ++ } ++ end_mask = tab[(bits >> 7) & 1]; ++ FB_WRITEL((end_mask & eorx) ^ bgx, dst); ++ } ++ dst1 += p->fix.line_length; ++ s += spitch; ++ } ++} ++ + void cfb_imageblit(struct fb_info *p, const struct fb_image *image) + { + u32 fgcolor, bgcolor, start_index, bitstart, pitch_index = 0; +@@ -294,11 +426,21 @@ void cfb_imageblit(struct fb_info *p, co + bgcolor = image->bg_color; + } + +- if (32 % bpp == 0 && !start_index && !pitch_index && +- ((width & (32/bpp-1)) == 0) && +- bpp >= 8 && bpp <= 32) +- fast_imageblit(image, p, dst1, fgcolor, bgcolor); +- else ++ if (!start_index && !pitch_index) { ++ if (bpp == 32) ++ fast_imageblit32(image, p, dst1, fgcolor, ++ bgcolor); ++ else if (bpp == 16 && (width & 1) == 0) ++ fast_imageblit16(image, p, dst1, fgcolor, ++ bgcolor); ++ else if (bpp == 8 && (width & 3) == 0) ++ fast_imageblit(image, p, dst1, fgcolor, ++ bgcolor); ++ else ++ slow_imageblit(image, p, dst1, fgcolor, ++ bgcolor, ++ start_index, pitch_index); ++ } else + slow_imageblit(image, p, dst1, fgcolor, bgcolor, + start_index, pitch_index); + } else diff --git a/target/linux/bcm27xx/patches-5.10/950-0045-dmaengine-Add-support-for-BCM2708.patch b/target/linux/bcm27xx/patches-5.10/950-0045-dmaengine-Add-support-for-BCM2708.patch new file mode 100644 index 0000000000..55d9a91dd6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0045-dmaengine-Add-support-for-BCM2708.patch @@ -0,0 +1,640 @@ +From 9ac0f4ce3beaad7700af1e771776d12ae7813f97 Mon Sep 17 00:00:00 2001 +From: Florian Meier +Date: Fri, 22 Nov 2013 14:22:53 +0100 +Subject: [PATCH] dmaengine: Add support for BCM2708 +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Add support for DMA controller of BCM2708 as used in the Raspberry Pi. +Currently it only supports cyclic DMA. + +Signed-off-by: Florian Meier + +dmaengine: expand functionality by supporting scatter/gather transfers sdhci-bcm2708 and dma.c: fix for LITE channels + +DMA: fix cyclic LITE length overflow bug + +dmaengine: bcm2708: Remove chancnt affectations + +Mirror bcm2835-dma.c commit 9eba5536a7434c69d8c185d4bd1c70734d92287d: +chancnt is already filled by dma_async_device_register, which uses the channel +list to know how much channels there is. + +Since it's already filled, we can safely remove it from the drivers' probe +function. + +Signed-off-by: Noralf Trønnes + +dmaengine: bcm2708: overwrite dreq only if it is not set + +dreq is set when the DMA channel is fetched from Device Tree. +slave_id is set using dmaengine_slave_config(). +Only overwrite dreq with slave_id if it is not set. + +dreq/slave_id in the cyclic DMA case is not touched, because I don't +have hardware to test with. + +Signed-off-by: Noralf Trønnes + +dmaengine: bcm2708: do device registration in the board file + +Don't register the device in the driver. Do it in the board file. + +Signed-off-by: Noralf Trønnes + +dmaengine: bcm2708: don't restrict DT support to ARCH_BCM2835 + +Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now. +Add Device Tree support to the non ARCH_BCM2835 case. +Use the same driver name regardless of architecture. + +Signed-off-by: Noralf Trønnes + +BCM270x_DT: add bcm2835-dma entry + +Add Device Tree entry for bcm2835-dma. +The entry doesn't contain any resources since they are handled +by the arch/arm/mach-bcm270x/dma.c driver. +In non-DT mode, don't add the device in the board file. + +Signed-off-by: Noralf Trønnes + +bcm2708-dmaengine: Add debug options + +BCM270x: Add memory and irq resources to dmaengine device and DT + +Prepare for merging of the legacy DMA API arch driver dma.c +with bcm2708-dmaengine by adding memory and irq resources both +to platform file device and Device Tree node. +Don't use BCM_DMAMAN_DRIVER_NAME so we don't have to include mach/dma.h + +Signed-off-by: Noralf Trønnes + +dmaengine: bcm2708: Merge with arch dma.c driver and disable dma.c + +Merge the legacy DMA API driver with bcm2708-dmaengine. +This is done so we can use bcm2708_fb on ARCH_BCM2835 (mailbox +driver is also needed). + +Changes to the dma.c code: +- Use BIT() macro. +- Cutdown some comments to one line. +- Add mutex to vc_dmaman and use this, since the dev lock is locked + during probing of the engine part. +- Add global g_dmaman variable since drvdata is used by the engine part. +- Restructure for readability: + vc_dmaman_chan_alloc() + vc_dmaman_chan_free() + bcm_dma_chan_free() +- Restructure bcm_dma_chan_alloc() to simplify error handling. +- Use device irq resources instead of hardcoded bcm_dma_irqs table. +- Remove dev_dmaman_register() and code it directly. +- Remove dev_dmaman_deregister() and code it directly. +- Simplify bcm_dmaman_probe() using devm_* functions. +- Get dmachans from DT if available. +- Keep 'dma.dmachans' module argument name for backwards compatibility. + +Make it available on ARCH_BCM2835 as well. + +Signed-off-by: Noralf Trønnes + +dmaengine: bcm2708: set residue_granularity field + +bcm2708-dmaengine supports residue reporting at burst level +but didn't report this via the residue_granularity field. + +Without this field set properly we get playback issues with I2S cards. + +dmaengine: bcm2708-dmaengine: Fix memory leak when stopping a running transfer + +bcm2708-dmaengine: Use more DMA channels (but not 12) + +1) Only the bcm2708_fb drivers uses the legacy DMA API, and +it requires a BULK-capable channel, so all other types +(FAST, NORMAL and LITE) can be made available to the regular +DMA API. + +2) DMA channels 11-14 share an interrupt. The driver can't +handle this, so don't use channels 12-14 (12 was used, probably +because it appears to have an interrupt, but in reality that +interrupt is for activity on ANY channel). This may explain +a lockup encountered when running out of DMA channels. + +The combined effect of this patch is to leave 7 DMA channels +available + channel 0 for bcm2708_fb via the legacy API. + +See: https://github.com/raspberrypi/linux/issues/1110 + https://github.com/raspberrypi/linux/issues/1108 + +dmaengine: bcm2708: Make legacy API available for bcm2835-dma + +bcm2708_fb uses the legacy DMA API, so in order to start using +bcm2835-dma, bcm2835-dma has to support the legacy API. Make this +possible by exporting bcm_dmaman_probe() and bcm_dmaman_remove(). + +Signed-off-by: Noralf Trønnes + +dmaengine: bcm2708: Change DT compatible string + +Both bcm2835-dma and bcm2708-dmaengine have the same compatible string. +So change compatible to "brcm,bcm2708-dma". + +Signed-off-by: Noralf Trønnes + +dmaengine: bcm2708: Remove driver but keep legacy API + +Dropping non-DT support means we don't need this driver, +but we still need the legacy DMA API. + +Signed-off-by: Noralf Trønnes + +bcm2708-dmaengine - Fix arm64 portability/build issues + +dma-bcm2708: Fix module compilation of CONFIG_DMA_BCM2708 + +bcm2708-dmaengine.c defines functions like bcm_dma_start which are +defined as well in dma-bcm2708.h as inline versions when +CONFIG_DMA_BCM2708 is not defined. This works fine when +CONFIG_DMA_BCM2708 is built in, but when it is selected as module build +fails with redefinition errors because in the build system when +CONFIG_DMA_BCM2708 is selected as module, the macro becomes +CONFIG_DMA_BCM2708_MODULE. + +This patch makes the header use CONFIG_DMA_BCM2708_MODULE too when +available. + +Fixes https://github.com/raspberrypi/linux/issues/2056 + +Signed-off-by: Andrei Gherzan +--- + drivers/dma/Kconfig | 6 +- + drivers/dma/Makefile | 1 + + drivers/dma/bcm2708-dmaengine.c | 281 ++++++++++++++++++++++ + include/linux/platform_data/dma-bcm2708.h | 143 +++++++++++ + 4 files changed, 430 insertions(+), 1 deletion(-) + create mode 100644 drivers/dma/bcm2708-dmaengine.c + create mode 100644 include/linux/platform_data/dma-bcm2708.h + +--- a/drivers/dma/Kconfig ++++ b/drivers/dma/Kconfig +@@ -134,7 +134,7 @@ config COH901318 + + config DMA_BCM2835 + tristate "BCM2835 DMA engine support" +- depends on ARCH_BCM2835 || ARCH_BCM2708 || ARCH_BCM2709 ++ depends on ARCH_BCM2835 + select DMA_ENGINE + select DMA_VIRTUAL_CHANNELS + +@@ -652,6 +652,10 @@ config UNIPHIER_XDMAC + UniPhier platform. This DMA controller can transfer data from + memory to memory, memory to peripheral and peripheral to memory. + ++config DMA_BCM2708 ++ tristate "BCM2708 DMA legacy API support" ++ depends on DMA_BCM2835 ++ + config XGENE_DMA + tristate "APM X-Gene DMA support" + depends on ARCH_XGENE || COMPILE_TEST +--- a/drivers/dma/Makefile ++++ b/drivers/dma/Makefile +@@ -21,6 +21,7 @@ obj-$(CONFIG_AT_XDMAC) += at_xdmac.o + obj-$(CONFIG_AXI_DMAC) += dma-axi-dmac.o + obj-$(CONFIG_BCM_SBA_RAID) += bcm-sba-raid.o + obj-$(CONFIG_COH901318) += coh901318.o coh901318_lli.o ++obj-$(CONFIG_DMA_BCM2708) += bcm2708-dmaengine.o + obj-$(CONFIG_DMA_BCM2835) += bcm2835-dma.o + obj-$(CONFIG_DMA_JZ4780) += dma-jz4780.o + obj-$(CONFIG_DMA_SA11X0) += sa11x0-dma.o +--- /dev/null ++++ b/drivers/dma/bcm2708-dmaengine.c +@@ -0,0 +1,281 @@ ++/* ++ * BCM2708 legacy DMA API ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License as published by ++ * the Free Software Foundation; either version 2 of the License, or ++ * (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "virt-dma.h" ++ ++#define CACHE_LINE_MASK 31 ++#define DEFAULT_DMACHAN_BITMAP 0x10 /* channel 4 only */ ++ ++/* valid only for channels 0 - 14, 15 has its own base address */ ++#define BCM2708_DMA_CHAN(n) ((n) << 8) /* base address */ ++#define BCM2708_DMA_CHANIO(dma_base, n) \ ++ ((void __iomem *)((char *)(dma_base) + BCM2708_DMA_CHAN(n))) ++ ++struct vc_dmaman { ++ void __iomem *dma_base; ++ u32 chan_available; /* bitmap of available channels */ ++ u32 has_feature[BCM_DMA_FEATURE_COUNT]; /* bitmap of feature presence */ ++ struct mutex lock; ++}; ++ ++static struct device *dmaman_dev; /* we assume there's only one! */ ++static struct vc_dmaman *g_dmaman; /* DMA manager */ ++ ++/* DMA Auxiliary Functions */ ++ ++/* A DMA buffer on an arbitrary boundary may separate a cache line into a ++ section inside the DMA buffer and another section outside it. ++ Even if we flush DMA buffers from the cache there is always the chance that ++ during a DMA someone will access the part of a cache line that is outside ++ the DMA buffer - which will then bring in unwelcome data. ++ Without being able to dictate our own buffer pools we must insist that ++ DMA buffers consist of a whole number of cache lines. ++*/ ++extern int bcm_sg_suitable_for_dma(struct scatterlist *sg_ptr, int sg_len) ++{ ++ int i; ++ ++ for (i = 0; i < sg_len; i++) { ++ if (sg_ptr[i].offset & CACHE_LINE_MASK || ++ sg_ptr[i].length & CACHE_LINE_MASK) ++ return 0; ++ } ++ ++ return 1; ++} ++EXPORT_SYMBOL_GPL(bcm_sg_suitable_for_dma); ++ ++extern void bcm_dma_start(void __iomem *dma_chan_base, ++ dma_addr_t control_block) ++{ ++ dsb(sy); /* ARM data synchronization (push) operation */ ++ ++ writel(control_block, dma_chan_base + BCM2708_DMA_ADDR); ++ writel(BCM2708_DMA_ACTIVE, dma_chan_base + BCM2708_DMA_CS); ++} ++EXPORT_SYMBOL_GPL(bcm_dma_start); ++ ++extern void bcm_dma_wait_idle(void __iomem *dma_chan_base) ++{ ++ dsb(sy); ++ ++ /* ugly busy wait only option for now */ ++ while (readl(dma_chan_base + BCM2708_DMA_CS) & BCM2708_DMA_ACTIVE) ++ cpu_relax(); ++} ++EXPORT_SYMBOL_GPL(bcm_dma_wait_idle); ++ ++extern bool bcm_dma_is_busy(void __iomem *dma_chan_base) ++{ ++ dsb(sy); ++ ++ return readl(dma_chan_base + BCM2708_DMA_CS) & BCM2708_DMA_ACTIVE; ++} ++EXPORT_SYMBOL_GPL(bcm_dma_is_busy); ++ ++/* Complete an ongoing DMA (assuming its results are to be ignored) ++ Does nothing if there is no DMA in progress. ++ This routine waits for the current AXI transfer to complete before ++ terminating the current DMA. If the current transfer is hung on a DREQ used ++ by an uncooperative peripheral the AXI transfer may never complete. In this ++ case the routine times out and return a non-zero error code. ++ Use of this routine doesn't guarantee that the ongoing or aborted DMA ++ does not produce an interrupt. ++*/ ++extern int bcm_dma_abort(void __iomem *dma_chan_base) ++{ ++ unsigned long int cs; ++ int rc = 0; ++ ++ cs = readl(dma_chan_base + BCM2708_DMA_CS); ++ ++ if (BCM2708_DMA_ACTIVE & cs) { ++ long int timeout = 10000; ++ ++ /* write 0 to the active bit - pause the DMA */ ++ writel(0, dma_chan_base + BCM2708_DMA_CS); ++ ++ /* wait for any current AXI transfer to complete */ ++ while (0 != (cs & BCM2708_DMA_ISPAUSED) && --timeout >= 0) ++ cs = readl(dma_chan_base + BCM2708_DMA_CS); ++ ++ if (0 != (cs & BCM2708_DMA_ISPAUSED)) { ++ /* we'll un-pause when we set of our next DMA */ ++ rc = -ETIMEDOUT; ++ ++ } else if (BCM2708_DMA_ACTIVE & cs) { ++ /* terminate the control block chain */ ++ writel(0, dma_chan_base + BCM2708_DMA_NEXTCB); ++ ++ /* abort the whole DMA */ ++ writel(BCM2708_DMA_ABORT | BCM2708_DMA_ACTIVE, ++ dma_chan_base + BCM2708_DMA_CS); ++ } ++ } ++ ++ return rc; ++} ++EXPORT_SYMBOL_GPL(bcm_dma_abort); ++ ++ /* DMA Manager Device Methods */ ++ ++static void vc_dmaman_init(struct vc_dmaman *dmaman, void __iomem *dma_base, ++ u32 chans_available) ++{ ++ dmaman->dma_base = dma_base; ++ dmaman->chan_available = chans_available; ++ dmaman->has_feature[BCM_DMA_FEATURE_FAST_ORD] = 0x0c; /* 2 & 3 */ ++ dmaman->has_feature[BCM_DMA_FEATURE_BULK_ORD] = 0x01; /* 0 */ ++ dmaman->has_feature[BCM_DMA_FEATURE_NORMAL_ORD] = 0xfe; /* 1 to 7 */ ++ dmaman->has_feature[BCM_DMA_FEATURE_LITE_ORD] = 0x7f00; /* 8 to 14 */ ++} ++ ++static int vc_dmaman_chan_alloc(struct vc_dmaman *dmaman, ++ unsigned required_feature_set) ++{ ++ u32 chans; ++ int chan = 0; ++ int feature; ++ ++ chans = dmaman->chan_available; ++ for (feature = 0; feature < BCM_DMA_FEATURE_COUNT; feature++) ++ /* select the subset of available channels with the desired ++ features */ ++ if (required_feature_set & (1 << feature)) ++ chans &= dmaman->has_feature[feature]; ++ ++ if (!chans) ++ return -ENOENT; ++ ++ /* return the ordinal of the first channel in the bitmap */ ++ while (chans != 0 && (chans & 1) == 0) { ++ chans >>= 1; ++ chan++; ++ } ++ /* claim the channel */ ++ dmaman->chan_available &= ~(1 << chan); ++ ++ return chan; ++} ++ ++static int vc_dmaman_chan_free(struct vc_dmaman *dmaman, int chan) ++{ ++ if (chan < 0) ++ return -EINVAL; ++ ++ if ((1 << chan) & dmaman->chan_available) ++ return -EIDRM; ++ ++ dmaman->chan_available |= (1 << chan); ++ ++ return 0; ++} ++ ++/* DMA Manager Monitor */ ++ ++extern int bcm_dma_chan_alloc(unsigned required_feature_set, ++ void __iomem **out_dma_base, int *out_dma_irq) ++{ ++ struct vc_dmaman *dmaman = g_dmaman; ++ struct platform_device *pdev = to_platform_device(dmaman_dev); ++ struct resource *r; ++ int chan; ++ ++ if (!dmaman_dev) ++ return -ENODEV; ++ ++ mutex_lock(&dmaman->lock); ++ chan = vc_dmaman_chan_alloc(dmaman, required_feature_set); ++ if (chan < 0) ++ goto out; ++ ++ r = platform_get_resource(pdev, IORESOURCE_IRQ, (unsigned int)chan); ++ if (!r) { ++ dev_err(dmaman_dev, "failed to get irq for DMA channel %d\n", ++ chan); ++ vc_dmaman_chan_free(dmaman, chan); ++ chan = -ENOENT; ++ goto out; ++ } ++ ++ *out_dma_base = BCM2708_DMA_CHANIO(dmaman->dma_base, chan); ++ *out_dma_irq = r->start; ++ dev_dbg(dmaman_dev, ++ "Legacy API allocated channel=%d, base=%p, irq=%i\n", ++ chan, *out_dma_base, *out_dma_irq); ++ ++out: ++ mutex_unlock(&dmaman->lock); ++ ++ return chan; ++} ++EXPORT_SYMBOL_GPL(bcm_dma_chan_alloc); ++ ++extern int bcm_dma_chan_free(int channel) ++{ ++ struct vc_dmaman *dmaman = g_dmaman; ++ int rc; ++ ++ if (!dmaman_dev) ++ return -ENODEV; ++ ++ mutex_lock(&dmaman->lock); ++ rc = vc_dmaman_chan_free(dmaman, channel); ++ mutex_unlock(&dmaman->lock); ++ ++ return rc; ++} ++EXPORT_SYMBOL_GPL(bcm_dma_chan_free); ++ ++int bcm_dmaman_probe(struct platform_device *pdev, void __iomem *base, ++ u32 chans_available) ++{ ++ struct device *dev = &pdev->dev; ++ struct vc_dmaman *dmaman; ++ ++ dmaman = devm_kzalloc(dev, sizeof(*dmaman), GFP_KERNEL); ++ if (!dmaman) ++ return -ENOMEM; ++ ++ mutex_init(&dmaman->lock); ++ vc_dmaman_init(dmaman, base, chans_available); ++ g_dmaman = dmaman; ++ dmaman_dev = dev; ++ ++ dev_info(dev, "DMA legacy API manager, dmachans=0x%x\n", ++ chans_available); ++ ++ return 0; ++} ++EXPORT_SYMBOL(bcm_dmaman_probe); ++ ++int bcm_dmaman_remove(struct platform_device *pdev) ++{ ++ dmaman_dev = NULL; ++ ++ return 0; ++} ++EXPORT_SYMBOL(bcm_dmaman_remove); ++ ++MODULE_LICENSE("GPL"); +--- /dev/null ++++ b/include/linux/platform_data/dma-bcm2708.h +@@ -0,0 +1,143 @@ ++/* ++ * Copyright (C) 2010 Broadcom ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++ ++#ifndef _PLAT_BCM2708_DMA_H ++#define _PLAT_BCM2708_DMA_H ++ ++/* DMA CS Control and Status bits */ ++#define BCM2708_DMA_ACTIVE BIT(0) ++#define BCM2708_DMA_INT BIT(2) ++#define BCM2708_DMA_ISPAUSED BIT(4) /* Pause requested or not active */ ++#define BCM2708_DMA_ISHELD BIT(5) /* Is held by DREQ flow control */ ++#define BCM2708_DMA_ERR BIT(8) ++#define BCM2708_DMA_ABORT BIT(30) /* stop current CB, go to next, WO */ ++#define BCM2708_DMA_RESET BIT(31) /* WO, self clearing */ ++ ++/* DMA control block "info" field bits */ ++#define BCM2708_DMA_INT_EN BIT(0) ++#define BCM2708_DMA_TDMODE BIT(1) ++#define BCM2708_DMA_WAIT_RESP BIT(3) ++#define BCM2708_DMA_D_INC BIT(4) ++#define BCM2708_DMA_D_WIDTH BIT(5) ++#define BCM2708_DMA_D_DREQ BIT(6) ++#define BCM2708_DMA_S_INC BIT(8) ++#define BCM2708_DMA_S_WIDTH BIT(9) ++#define BCM2708_DMA_S_DREQ BIT(10) ++ ++#define BCM2708_DMA_BURST(x) (((x) & 0xf) << 12) ++#define BCM2708_DMA_PER_MAP(x) ((x) << 16) ++#define BCM2708_DMA_WAITS(x) (((x) & 0x1f) << 21) ++ ++#define BCM2708_DMA_DREQ_EMMC 11 ++#define BCM2708_DMA_DREQ_SDHOST 13 ++ ++#define BCM2708_DMA_CS 0x00 /* Control and Status */ ++#define BCM2708_DMA_ADDR 0x04 ++/* the current control block appears in the following registers - read only */ ++#define BCM2708_DMA_INFO 0x08 ++#define BCM2708_DMA_SOURCE_AD 0x0c ++#define BCM2708_DMA_DEST_AD 0x10 ++#define BCM2708_DMA_NEXTCB 0x1C ++#define BCM2708_DMA_DEBUG 0x20 ++ ++#define BCM2708_DMA4_CS (BCM2708_DMA_CHAN(4) + BCM2708_DMA_CS) ++#define BCM2708_DMA4_ADDR (BCM2708_DMA_CHAN(4) + BCM2708_DMA_ADDR) ++ ++#define BCM2708_DMA_TDMODE_LEN(w, h) ((h) << 16 | (w)) ++ ++/* When listing features we can ask for when allocating DMA channels give ++ those with higher priority smaller ordinal numbers */ ++#define BCM_DMA_FEATURE_FAST_ORD 0 ++#define BCM_DMA_FEATURE_BULK_ORD 1 ++#define BCM_DMA_FEATURE_NORMAL_ORD 2 ++#define BCM_DMA_FEATURE_LITE_ORD 3 ++#define BCM_DMA_FEATURE_FAST BIT(BCM_DMA_FEATURE_FAST_ORD) ++#define BCM_DMA_FEATURE_BULK BIT(BCM_DMA_FEATURE_BULK_ORD) ++#define BCM_DMA_FEATURE_NORMAL BIT(BCM_DMA_FEATURE_NORMAL_ORD) ++#define BCM_DMA_FEATURE_LITE BIT(BCM_DMA_FEATURE_LITE_ORD) ++#define BCM_DMA_FEATURE_COUNT 4 ++ ++struct bcm2708_dma_cb { ++ u32 info; ++ u32 src; ++ u32 dst; ++ u32 length; ++ u32 stride; ++ u32 next; ++ u32 pad[2]; ++}; ++ ++struct scatterlist; ++struct platform_device; ++ ++#if defined(CONFIG_DMA_BCM2708) || defined(CONFIG_DMA_BCM2708_MODULE) ++ ++int bcm_sg_suitable_for_dma(struct scatterlist *sg_ptr, int sg_len); ++void bcm_dma_start(void __iomem *dma_chan_base, dma_addr_t control_block); ++void bcm_dma_wait_idle(void __iomem *dma_chan_base); ++bool bcm_dma_is_busy(void __iomem *dma_chan_base); ++int bcm_dma_abort(void __iomem *dma_chan_base); ++ ++/* return channel no or -ve error */ ++int bcm_dma_chan_alloc(unsigned preferred_feature_set, ++ void __iomem **out_dma_base, int *out_dma_irq); ++int bcm_dma_chan_free(int channel); ++ ++int bcm_dmaman_probe(struct platform_device *pdev, void __iomem *base, ++ u32 chans_available); ++int bcm_dmaman_remove(struct platform_device *pdev); ++ ++#else /* CONFIG_DMA_BCM2708 */ ++ ++static inline int bcm_sg_suitable_for_dma(struct scatterlist *sg_ptr, ++ int sg_len) ++{ ++ return 0; ++} ++ ++static inline void bcm_dma_start(void __iomem *dma_chan_base, ++ dma_addr_t control_block) { } ++ ++static inline void bcm_dma_wait_idle(void __iomem *dma_chan_base) { } ++ ++static inline bool bcm_dma_is_busy(void __iomem *dma_chan_base) ++{ ++ return false; ++} ++ ++static inline int bcm_dma_abort(void __iomem *dma_chan_base) ++{ ++ return -EINVAL; ++} ++ ++static inline int bcm_dma_chan_alloc(unsigned preferred_feature_set, ++ void __iomem **out_dma_base, ++ int *out_dma_irq) ++{ ++ return -EINVAL; ++} ++ ++static inline int bcm_dma_chan_free(int channel) ++{ ++ return -EINVAL; ++} ++ ++static inline int bcm_dmaman_probe(struct platform_device *pdev, ++ void __iomem *base, u32 chans_available) ++{ ++ return 0; ++} ++ ++static inline int bcm_dmaman_remove(struct platform_device *pdev) ++{ ++ return 0; ++} ++ ++#endif /* CONFIG_DMA_BCM2708 || CONFIG_DMA_BCM2708_MODULE */ ++ ++#endif /* _PLAT_BCM2708_DMA_H */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0046-MMC-added-alternative-MMC-driver.patch b/target/linux/bcm27xx/patches-5.10/950-0046-MMC-added-alternative-MMC-driver.patch new file mode 100644 index 0000000000..aeba685ae2 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0046-MMC-added-alternative-MMC-driver.patch @@ -0,0 +1,1933 @@ +From 364272893877af2ac5f331010d6f6f088c198e31 Mon Sep 17 00:00:00 2001 +From: gellert +Date: Fri, 15 Aug 2014 16:35:06 +0100 +Subject: [PATCH] MMC: added alternative MMC driver +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +mmc: Disable CMD23 transfers on all cards + +Pending wire-level investigation of these types of transfers +and associated errors on bcm2835-mmc, disable for now. Fallback of +CMD18/CMD25 transfers will be used automatically by the MMC layer. + +Reported/Tested-by: Gellert Weisz + +mmc: bcm2835-mmc: enable DT support for all architectures + +Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now. +Enable Device Tree support for all architectures. + +Signed-off-by: Noralf Trønnes + +mmc: bcm2835-mmc: fix probe error handling + +Probe error handling is broken in several places. +Simplify error handling by using device managed functions. +Replace pr_{err,info} with dev_{err,info}. + +Signed-off-by: Noralf Trønnes + +bcm2835-mmc: Add locks when accessing sdhost registers + +bcm2835-mmc: Add range of debug options for slowing things down + +bcm2835-mmc: Add option to disable some delays + +bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23 + +bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23 + +bcm2835-mmc: Adding overclocking option + +Allow a different clock speed to be substitued for a requested 50MHz. +This option is exposed using the "overclock_50" DT parameter. +Note that the mmc interface is restricted to EVEN integer divisions of +250MHz, and the highest sensible option is 63 (250/4 = 62.5), the +next being 125 (250/2) which is much too high. + +Use at your own risk. + +bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz + +Also only warn once for each overclock setting. + +mmc: bcm2835-mmc: Make available on ARCH_BCM2835 + +Make the bcm2835-mmc driver available for use on ARCH_BCM2835. + +Signed-off-by: Noralf Trønnes + +BCM270x_DT: add bcm2835-mmc entry + +Add Device Tree entry for bcm2835-mmc. +In non-DT mode, don't add the device in the board file. + +Signed-off-by: Noralf Trønnes + +bcm2835-mmc: Don't overwrite MMC capabilities from DT + +bcm2835-mmc: Don't override bus width capabilities from devicetree + +Take out the force setting of the MMC_CAP_4_BIT_DATA host capability +so that the result read from devicetree via mmc_of_parse() is +preserved. + +bcm2835-mmc: Only claim one DMA channel + +With both MMC controllers enabled there are few DMA channels left. The +bcm2835-mmc driver only uses DMA in one direction at a time, so it +doesn't need to claim two channels. + +See: https://github.com/raspberrypi/linux/issues/1327 + +Signed-off-by: Phil Elwell + +bcm2835-mmc: New timer API + +mmc: bcm2835-mmc: Support underclocking + +Support underclocking of the SD bus using the max-frequency DT property +(which currently has no DT parameter). The sd_overclock parameter +already provides another way to achieve the same thing which should be +equivalent in end result, but it is a bug not to support max-frequency +as well. + +See: https://github.com/raspberrypi/linux/issues/2350 + +Signed-off-by: Phil Elwell + +mmc/bcm2835: Recover from MMC_SEND_EXT_CSD + +If the user issues an "mmc extcsd read", the SD controller receives +what it thinks is a SEND_IF_COND command with an unexpected data block. +The resulting operations leave the FSM stuck in READWAIT, a state which +persists until the MMC framework resets the controller, by which point +the root filesystem is likely to have been unmounted. + +A less heavyweight solution is to detect the condition and nudge the +FSM by asserting the (self-clearing) FORCE_DATA_MODE bit. + +N.B. This workaround was essentially discovered by accident and without +a full understanding the inner workings of the controller, so it is +fortunate that the "fix" only modifies error paths. + +See: https://github.com/raspberrypi/linux/issues/2728 + +Signed-off-by: Phil Elwell + +bcm2835-mmc: Fix DMA channel leak + +The BCM2835 MMC host driver requests a DMA channel on probe but neglects +to release the channel in the probe error path and on driver unbind. + +I'm seeing this happen on every boot of the Compute Module 3: On first +driver probe, DMA channel 2 is allocated and then leaked with a "could +not get clk, deferring probe" message. On second driver probe, channel 4 +is allocated. + +Fix it. + +Signed-off-by: Lukas Wunner +Cc: Frank Pavlic + +bcm2835-mmc: Fix struct mmc_host leak on probe + +The BCM2835 MMC host driver requests the bus address of the host's +register map on probe. If that fails, the driver leaks the struct +mmc_host allocated earlier. + +Fix it. + +Signed-off-by: Lukas Wunner +Cc: Frank Pavlic + +bcm2835-mmc: Fix duplicate free_irq() on remove + +The BCM2835 MMC host driver requests its interrupt as a device-managed +resource, so the interrupt is automatically freed after the driver is +unbound. + +However on driver unbind, bcm2835_mmc_remove() frees the interrupt +explicitly to avoid invocation of the interrupt handler after driver +structures have been torn down. + +The interrupt is thus freed twice, leading to a WARN splat in +__free_irq(). Fix by not requesting the interrupt as a device-managed +resource. + +Signed-off-by: Lukas Wunner +Cc: Frank Pavlic + +bcm2835-mmc: Handle mmc_add_host() errors + +The BCM2835 MMC host driver calls mmc_add_host() but doesn't check its +return value. Errors occurring in that function are therefore not +handled. Fix it. + +Signed-off-by: Lukas Wunner +Cc: Frank Pavlic + +bcm2835-mmc: Deduplicate reset of driver data on remove + +The BCM2835 MMC host driver sets the device's driver data pointer to +NULL on ->remove() even though the driver core subsequently does the +same in __device_release_driver(). Drop the duplicate assignment. + +Signed-off-by: Lukas Wunner +Cc: Frank Pavlic + +bcm2835_mmc: Remove vestigial threaded IRQ + +With SDIO processing now managed by the MMC framework with a +workqueue, the bcm2835_mmc driver no longer needs a threaded +IRQ. + +Signed-off-by: Phil Elwell + +Add missing dma_unmap_sg calls to free relevant swiotlb bounce buffers. +This prevents DMA leaks. + +Signed-off-by: Yaroslav Rosomakho + +Limit max_req_size under arm64 (or any other platform that uses swiotlb) to prevent potential buffer overflow due to bouncing. + +Signed-off-by: Yaroslav Rosomakho +--- + drivers/mmc/core/block.c | 28 +- + drivers/mmc/core/core.c | 3 +- + drivers/mmc/core/quirks.h | 8 + + drivers/mmc/host/Kconfig | 29 + + drivers/mmc/host/Makefile | 1 + + drivers/mmc/host/bcm2835-mmc.c | 1576 ++++++++++++++++++++++++++++++++ + include/linux/mmc/card.h | 2 + + 7 files changed, 1643 insertions(+), 4 deletions(-) + create mode 100644 drivers/mmc/host/bcm2835-mmc.c + +--- a/drivers/mmc/core/block.c ++++ b/drivers/mmc/core/block.c +@@ -165,6 +165,13 @@ static DEFINE_MUTEX(open_lock); + module_param(perdev_minors, int, 0444); + MODULE_PARM_DESC(perdev_minors, "Minors numbers to allocate per device"); + ++/* ++ * Allow quirks to be overridden for the current card ++ */ ++static char *card_quirks; ++module_param(card_quirks, charp, 0644); ++MODULE_PARM_DESC(card_quirks, "Force the use of the indicated quirks (a bitfield)"); ++ + static inline int mmc_blk_part_switch(struct mmc_card *card, + unsigned int part_type); + static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq, +@@ -2898,6 +2905,7 @@ static int mmc_blk_probe(struct mmc_card + { + struct mmc_blk_data *md, *part_md; + char cap_str[10]; ++ char quirk_str[24]; + + /* + * Check that the card supports the command class(es) we need. +@@ -2905,7 +2913,16 @@ static int mmc_blk_probe(struct mmc_card + if (!(card->csd.cmdclass & CCC_BLOCK_READ)) + return -ENODEV; + +- mmc_fixup_device(card, mmc_blk_fixups); ++ if (card_quirks) { ++ unsigned long quirks; ++ if (kstrtoul(card_quirks, 0, &quirks) == 0) ++ card->quirks = (unsigned int)quirks; ++ else ++ pr_err("mmc_block: Invalid card_quirks parameter '%s'\n", ++ card_quirks); ++ } ++ else ++ mmc_fixup_device(card, mmc_blk_fixups); + + card->complete_wq = alloc_workqueue("mmc_complete", + WQ_MEM_RECLAIM | WQ_HIGHPRI, 0); +@@ -2920,9 +2937,14 @@ static int mmc_blk_probe(struct mmc_card + + string_get_size((u64)get_capacity(md->disk), 512, STRING_UNITS_2, + cap_str, sizeof(cap_str)); +- pr_info("%s: %s %s %s %s\n", ++ if (card->quirks) ++ snprintf(quirk_str, sizeof(quirk_str), ++ " (quirks 0x%08x)", card->quirks); ++ else ++ quirk_str[0] = '\0'; ++ pr_info("%s: %s %s %s%s%s\n", + md->disk->disk_name, mmc_card_id(card), mmc_card_name(card), +- cap_str, md->read_only ? "(ro)" : ""); ++ cap_str, md->read_only ? " (ro)" : "", quirk_str); + + if (mmc_blk_alloc_parts(card, md)) + goto out; +--- a/drivers/mmc/core/core.c ++++ b/drivers/mmc/core/core.c +@@ -1874,7 +1874,8 @@ EXPORT_SYMBOL(mmc_erase); + + int mmc_can_erase(struct mmc_card *card) + { +- if (card->csd.cmdclass & CCC_ERASE && card->erase_size) ++ if (card->csd.cmdclass & CCC_ERASE && card->erase_size && ++ !(card->quirks & MMC_QUIRK_ERASE_BROKEN)) + return 1; + return 0; + } +--- a/drivers/mmc/core/quirks.h ++++ b/drivers/mmc/core/quirks.h +@@ -99,6 +99,14 @@ static const struct mmc_fixup __maybe_un + MMC_FIXUP("V10016", CID_MANFID_KINGSTON, CID_OEMID_ANY, add_quirk_mmc, + MMC_QUIRK_TRIM_BROKEN), + ++ /* ++ * On some Kingston SD cards, multiple erases of less than 64 ++ * sectors can cause corruption. ++ */ ++ MMC_FIXUP("SD16G", 0x41, 0x3432, add_quirk, MMC_QUIRK_ERASE_BROKEN), ++ MMC_FIXUP("SD32G", 0x41, 0x3432, add_quirk, MMC_QUIRK_ERASE_BROKEN), ++ MMC_FIXUP("SD64G", 0x41, 0x3432, add_quirk, MMC_QUIRK_ERASE_BROKEN), ++ + END_FIXUP + }; + +--- a/drivers/mmc/host/Kconfig ++++ b/drivers/mmc/host/Kconfig +@@ -5,6 +5,35 @@ + + comment "MMC/SD/SDIO Host Controller Drivers" + ++config MMC_BCM2835_MMC ++ tristate "MMC support on BCM2835" ++ depends on MACH_BCM2708 || MACH_BCM2709 || ARCH_BCM2835 ++ help ++ This selects the MMC Interface on BCM2835. ++ ++ If you have a controller with this interface, say Y or M here. ++ ++ If unsure, say N. ++ ++config MMC_BCM2835_DMA ++ bool "DMA support on BCM2835 Arasan controller" ++ depends on MMC_BCM2835_MMC ++ help ++ Enable DMA support on the Arasan SDHCI controller in Broadcom 2708 ++ based chips. ++ ++ If unsure, say N. ++ ++config MMC_BCM2835_PIO_DMA_BARRIER ++ int "Block count limit for PIO transfers" ++ depends on MMC_BCM2835_MMC && MMC_BCM2835_DMA ++ range 0 256 ++ default 2 ++ help ++ The inclusive limit in bytes under which PIO will be used instead of DMA ++ ++ If unsure, say 2 here. ++ + config MMC_DEBUG + bool "MMC host drivers debugging" + depends on MMC != n +--- a/drivers/mmc/host/Makefile ++++ b/drivers/mmc/host/Makefile +@@ -24,6 +24,7 @@ obj-$(CONFIG_MMC_SDHCI_F_SDH30) += sdhci + obj-$(CONFIG_MMC_SDHCI_MILBEAUT) += sdhci-milbeaut.o + obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o + obj-$(CONFIG_MMC_SDHCI_AM654) += sdhci_am654.o ++obj-$(CONFIG_MMC_BCM2835_MMC) += bcm2835-mmc.o + obj-$(CONFIG_MMC_WBSD) += wbsd.o + obj-$(CONFIG_MMC_AU1X) += au1xmmc.o + obj-$(CONFIG_MMC_ALCOR) += alcor.o +--- /dev/null ++++ b/drivers/mmc/host/bcm2835-mmc.c +@@ -0,0 +1,1576 @@ ++/* ++ * BCM2835 MMC host driver. ++ * ++ * Author: Gellert Weisz ++ * Copyright 2014 ++ * ++ * Based on ++ * sdhci-bcm2708.c by Broadcom ++ * sdhci-bcm2835.c by Stephen Warren and Oleksandr Tymoshenko ++ * sdhci.c and sdhci-pci.c by Pierre Ossman ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms and conditions of the GNU General Public License, ++ * version 2, as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope it will be useful, but WITHOUT ++ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or ++ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for ++ * more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program. If not, see . ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "sdhci.h" ++ ++ ++#define DRIVER_NAME "mmc-bcm2835" ++ ++#define DBG(f, x...) \ ++pr_debug(DRIVER_NAME " [%s()]: " f, __func__, ## x) ++ ++#ifndef CONFIG_MMC_BCM2835_DMA ++ #define FORCE_PIO ++#endif ++ ++ ++/* the inclusive limit in bytes under which PIO will be used instead of DMA */ ++#ifdef CONFIG_MMC_BCM2835_PIO_DMA_BARRIER ++#define PIO_DMA_BARRIER CONFIG_MMC_BCM2835_PIO_DMA_BARRIER ++#else ++#define PIO_DMA_BARRIER 00 ++#endif ++ ++#define MIN_FREQ 400000 ++#define TIMEOUT_VAL 0xE ++#define BCM2835_SDHCI_WRITE_DELAY(f) (((2 * 1000000) / f) + 1) ++ ++ ++unsigned mmc_debug; ++unsigned mmc_debug2; ++ ++struct bcm2835_host { ++ spinlock_t lock; ++ ++ void __iomem *ioaddr; ++ u32 bus_addr; ++ ++ struct mmc_host *mmc; ++ ++ u32 timeout; ++ ++ int clock; /* Current clock speed */ ++ u8 pwr; /* Current voltage */ ++ ++ unsigned int max_clk; /* Max possible freq */ ++ unsigned int timeout_clk; /* Timeout freq (KHz) */ ++ unsigned int clk_mul; /* Clock Muliplier value */ ++ ++ struct tasklet_struct finish_tasklet; /* Tasklet structures */ ++ ++ struct timer_list timer; /* Timer for timeouts */ ++ ++ struct sg_mapping_iter sg_miter; /* SG state for PIO */ ++ unsigned int blocks; /* remaining PIO blocks */ ++ ++ int irq; /* Device IRQ */ ++ ++ ++ u32 ier; /* cached registers */ ++ ++ struct mmc_request *mrq; /* Current request */ ++ struct mmc_command *cmd; /* Current command */ ++ struct mmc_data *data; /* Current data request */ ++ unsigned int data_early:1; /* Data finished before cmd */ ++ ++ wait_queue_head_t buf_ready_int; /* Waitqueue for Buffer Read Ready interrupt */ ++ ++ u32 shadow; ++ ++ /*DMA part*/ ++ struct dma_chan *dma_chan_rxtx; /* DMA channel for reads and writes */ ++ struct dma_slave_config dma_cfg_rx; ++ struct dma_slave_config dma_cfg_tx; ++ struct dma_async_tx_descriptor *tx_desc; /* descriptor */ ++ ++ bool have_dma; ++ bool use_dma; ++ bool wait_for_dma; ++ /*end of DMA part*/ ++ ++ int max_delay; /* maximum length of time spent waiting */ ++ ++ int flags; /* Host attributes */ ++#define SDHCI_REQ_USE_DMA (1<<2) /* Use DMA for this req. */ ++#define SDHCI_DEVICE_DEAD (1<<3) /* Device unresponsive */ ++#define SDHCI_AUTO_CMD12 (1<<6) /* Auto CMD12 support */ ++#define SDHCI_AUTO_CMD23 (1<<7) /* Auto CMD23 support */ ++#define SDHCI_SDIO_IRQ_ENABLED (1<<9) /* SDIO irq enabled */ ++ ++ u32 overclock_50; /* frequency to use when 50MHz is requested (in MHz) */ ++ u32 max_overclock; /* Highest reported */ ++}; ++ ++ ++static inline void bcm2835_mmc_writel(struct bcm2835_host *host, u32 val, int reg, int from) ++{ ++ unsigned delay; ++ lockdep_assert_held_once(&host->lock); ++ writel(val, host->ioaddr + reg); ++ udelay(BCM2835_SDHCI_WRITE_DELAY(max(host->clock, MIN_FREQ))); ++ ++ delay = ((mmc_debug >> 16) & 0xf) << ((mmc_debug >> 20) & 0xf); ++ if (delay && !((1<lock); ++ writel(val, host->ioaddr + reg); ++ ++ delay = ((mmc_debug >> 24) & 0xf) << ((mmc_debug >> 28) & 0xf); ++ if (delay) ++ udelay(delay); ++} ++ ++static inline u32 bcm2835_mmc_readl(struct bcm2835_host *host, int reg) ++{ ++ lockdep_assert_held_once(&host->lock); ++ return readl(host->ioaddr + reg); ++} ++ ++static inline void bcm2835_mmc_writew(struct bcm2835_host *host, u16 val, int reg) ++{ ++ u32 oldval = (reg == SDHCI_COMMAND) ? host->shadow : ++ bcm2835_mmc_readl(host, reg & ~3); ++ u32 word_num = (reg >> 1) & 1; ++ u32 word_shift = word_num * 16; ++ u32 mask = 0xffff << word_shift; ++ u32 newval = (oldval & ~mask) | (val << word_shift); ++ ++ if (reg == SDHCI_TRANSFER_MODE) ++ host->shadow = newval; ++ else ++ bcm2835_mmc_writel(host, newval, reg & ~3, 0); ++ ++} ++ ++static inline void bcm2835_mmc_writeb(struct bcm2835_host *host, u8 val, int reg) ++{ ++ u32 oldval = bcm2835_mmc_readl(host, reg & ~3); ++ u32 byte_num = reg & 3; ++ u32 byte_shift = byte_num * 8; ++ u32 mask = 0xff << byte_shift; ++ u32 newval = (oldval & ~mask) | (val << byte_shift); ++ ++ bcm2835_mmc_writel(host, newval, reg & ~3, 1); ++} ++ ++ ++static inline u16 bcm2835_mmc_readw(struct bcm2835_host *host, int reg) ++{ ++ u32 val = bcm2835_mmc_readl(host, (reg & ~3)); ++ u32 word_num = (reg >> 1) & 1; ++ u32 word_shift = word_num * 16; ++ u32 word = (val >> word_shift) & 0xffff; ++ ++ return word; ++} ++ ++static inline u8 bcm2835_mmc_readb(struct bcm2835_host *host, int reg) ++{ ++ u32 val = bcm2835_mmc_readl(host, (reg & ~3)); ++ u32 byte_num = reg & 3; ++ u32 byte_shift = byte_num * 8; ++ u32 byte = (val >> byte_shift) & 0xff; ++ ++ return byte; ++} ++ ++static void bcm2835_mmc_unsignal_irqs(struct bcm2835_host *host, u32 clear) ++{ ++ u32 ier; ++ ++ ier = bcm2835_mmc_readl(host, SDHCI_SIGNAL_ENABLE); ++ ier &= ~clear; ++ /* change which requests generate IRQs - makes no difference to ++ the content of SDHCI_INT_STATUS, or the need to acknowledge IRQs */ ++ bcm2835_mmc_writel(host, ier, SDHCI_SIGNAL_ENABLE, 2); ++} ++ ++ ++static void bcm2835_mmc_dumpregs(struct bcm2835_host *host) ++{ ++ pr_debug(DRIVER_NAME ": =========== REGISTER DUMP (%s)===========\n", ++ mmc_hostname(host->mmc)); ++ ++ pr_debug(DRIVER_NAME ": Sys addr: 0x%08x | Version: 0x%08x\n", ++ bcm2835_mmc_readl(host, SDHCI_DMA_ADDRESS), ++ bcm2835_mmc_readw(host, SDHCI_HOST_VERSION)); ++ pr_debug(DRIVER_NAME ": Blk size: 0x%08x | Blk cnt: 0x%08x\n", ++ bcm2835_mmc_readw(host, SDHCI_BLOCK_SIZE), ++ bcm2835_mmc_readw(host, SDHCI_BLOCK_COUNT)); ++ pr_debug(DRIVER_NAME ": Argument: 0x%08x | Trn mode: 0x%08x\n", ++ bcm2835_mmc_readl(host, SDHCI_ARGUMENT), ++ bcm2835_mmc_readw(host, SDHCI_TRANSFER_MODE)); ++ pr_debug(DRIVER_NAME ": Present: 0x%08x | Host ctl: 0x%08x\n", ++ bcm2835_mmc_readl(host, SDHCI_PRESENT_STATE), ++ bcm2835_mmc_readb(host, SDHCI_HOST_CONTROL)); ++ pr_debug(DRIVER_NAME ": Power: 0x%08x | Blk gap: 0x%08x\n", ++ bcm2835_mmc_readb(host, SDHCI_POWER_CONTROL), ++ bcm2835_mmc_readb(host, SDHCI_BLOCK_GAP_CONTROL)); ++ pr_debug(DRIVER_NAME ": Wake-up: 0x%08x | Clock: 0x%08x\n", ++ bcm2835_mmc_readb(host, SDHCI_WAKE_UP_CONTROL), ++ bcm2835_mmc_readw(host, SDHCI_CLOCK_CONTROL)); ++ pr_debug(DRIVER_NAME ": Timeout: 0x%08x | Int stat: 0x%08x\n", ++ bcm2835_mmc_readb(host, SDHCI_TIMEOUT_CONTROL), ++ bcm2835_mmc_readl(host, SDHCI_INT_STATUS)); ++ pr_debug(DRIVER_NAME ": Int enab: 0x%08x | Sig enab: 0x%08x\n", ++ bcm2835_mmc_readl(host, SDHCI_INT_ENABLE), ++ bcm2835_mmc_readl(host, SDHCI_SIGNAL_ENABLE)); ++ pr_debug(DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n", ++ bcm2835_mmc_readw(host, SDHCI_AUTO_CMD_STATUS), ++ bcm2835_mmc_readw(host, SDHCI_SLOT_INT_STATUS)); ++ pr_debug(DRIVER_NAME ": Caps: 0x%08x | Caps_1: 0x%08x\n", ++ bcm2835_mmc_readl(host, SDHCI_CAPABILITIES), ++ bcm2835_mmc_readl(host, SDHCI_CAPABILITIES_1)); ++ pr_debug(DRIVER_NAME ": Cmd: 0x%08x | Max curr: 0x%08x\n", ++ bcm2835_mmc_readw(host, SDHCI_COMMAND), ++ bcm2835_mmc_readl(host, SDHCI_MAX_CURRENT)); ++ pr_debug(DRIVER_NAME ": Host ctl2: 0x%08x\n", ++ bcm2835_mmc_readw(host, SDHCI_HOST_CONTROL2)); ++ ++ pr_debug(DRIVER_NAME ": ===========================================\n"); ++} ++ ++ ++static void bcm2835_mmc_reset(struct bcm2835_host *host, u8 mask) ++{ ++ unsigned long timeout; ++ unsigned long flags; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ bcm2835_mmc_writeb(host, mask, SDHCI_SOFTWARE_RESET); ++ ++ if (mask & SDHCI_RESET_ALL) ++ host->clock = 0; ++ ++ /* Wait max 100 ms */ ++ timeout = 100; ++ ++ /* hw clears the bit when it's done */ ++ while (bcm2835_mmc_readb(host, SDHCI_SOFTWARE_RESET) & mask) { ++ if (timeout == 0) { ++ pr_err("%s: Reset 0x%x never completed.\n", ++ mmc_hostname(host->mmc), (int)mask); ++ bcm2835_mmc_dumpregs(host); ++ return; ++ } ++ timeout--; ++ spin_unlock_irqrestore(&host->lock, flags); ++ mdelay(1); ++ spin_lock_irqsave(&host->lock, flags); ++ } ++ ++ if (100-timeout > 10 && 100-timeout > host->max_delay) { ++ host->max_delay = 100-timeout; ++ pr_warn("Warning: MMC controller hung for %d ms\n", host->max_delay); ++ } ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static void bcm2835_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios); ++ ++static void bcm2835_mmc_init(struct bcm2835_host *host, int soft) ++{ ++ unsigned long flags; ++ if (soft) ++ bcm2835_mmc_reset(host, SDHCI_RESET_CMD|SDHCI_RESET_DATA); ++ else ++ bcm2835_mmc_reset(host, SDHCI_RESET_ALL); ++ ++ host->ier = SDHCI_INT_BUS_POWER | SDHCI_INT_DATA_END_BIT | ++ SDHCI_INT_DATA_CRC | SDHCI_INT_DATA_TIMEOUT | ++ SDHCI_INT_INDEX | SDHCI_INT_END_BIT | SDHCI_INT_CRC | ++ SDHCI_INT_TIMEOUT | SDHCI_INT_DATA_END | ++ SDHCI_INT_RESPONSE; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ bcm2835_mmc_writel(host, host->ier, SDHCI_INT_ENABLE, 3); ++ bcm2835_mmc_writel(host, host->ier, SDHCI_SIGNAL_ENABLE, 3); ++ spin_unlock_irqrestore(&host->lock, flags); ++ ++ if (soft) { ++ /* force clock reconfiguration */ ++ host->clock = 0; ++ bcm2835_mmc_set_ios(host->mmc, &host->mmc->ios); ++ } ++} ++ ++ ++ ++static void bcm2835_mmc_finish_data(struct bcm2835_host *host); ++ ++static void bcm2835_mmc_dma_complete(void *param) ++{ ++ struct bcm2835_host *host = param; ++ struct dma_chan *dma_chan; ++ unsigned long flags; ++ u32 dir_data; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ host->use_dma = false; ++ ++ if (host->data) { ++ dma_chan = host->dma_chan_rxtx; ++ if (host->data->flags & MMC_DATA_WRITE) ++ dir_data = DMA_TO_DEVICE; ++ else ++ dir_data = DMA_FROM_DEVICE; ++ dma_unmap_sg(dma_chan->device->dev, ++ host->data->sg, host->data->sg_len, ++ dir_data); ++ if (! (host->data->flags & MMC_DATA_WRITE)) ++ bcm2835_mmc_finish_data(host); ++ } else if (host->wait_for_dma) { ++ host->wait_for_dma = false; ++ tasklet_schedule(&host->finish_tasklet); ++ } ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static void bcm2835_bcm2835_mmc_read_block_pio(struct bcm2835_host *host) ++{ ++ unsigned long flags; ++ size_t blksize, len, chunk; ++ ++ u32 uninitialized_var(scratch); ++ u8 *buf; ++ ++ blksize = host->data->blksz; ++ chunk = 0; ++ ++ local_irq_save(flags); ++ ++ while (blksize) { ++ if (!sg_miter_next(&host->sg_miter)) ++ BUG(); ++ ++ len = min(host->sg_miter.length, blksize); ++ ++ blksize -= len; ++ host->sg_miter.consumed = len; ++ ++ buf = host->sg_miter.addr; ++ ++ while (len) { ++ if (chunk == 0) { ++ scratch = bcm2835_mmc_readl(host, SDHCI_BUFFER); ++ chunk = 4; ++ } ++ ++ *buf = scratch & 0xFF; ++ ++ buf++; ++ scratch >>= 8; ++ chunk--; ++ len--; ++ } ++ } ++ ++ sg_miter_stop(&host->sg_miter); ++ ++ local_irq_restore(flags); ++} ++ ++static void bcm2835_bcm2835_mmc_write_block_pio(struct bcm2835_host *host) ++{ ++ unsigned long flags; ++ size_t blksize, len, chunk; ++ u32 scratch; ++ u8 *buf; ++ ++ blksize = host->data->blksz; ++ chunk = 0; ++ chunk = 0; ++ scratch = 0; ++ ++ local_irq_save(flags); ++ ++ while (blksize) { ++ if (!sg_miter_next(&host->sg_miter)) ++ BUG(); ++ ++ len = min(host->sg_miter.length, blksize); ++ ++ blksize -= len; ++ host->sg_miter.consumed = len; ++ ++ buf = host->sg_miter.addr; ++ ++ while (len) { ++ scratch |= (u32)*buf << (chunk * 8); ++ ++ buf++; ++ chunk++; ++ len--; ++ ++ if ((chunk == 4) || ((len == 0) && (blksize == 0))) { ++ mmc_raw_writel(host, scratch, SDHCI_BUFFER); ++ chunk = 0; ++ scratch = 0; ++ } ++ } ++ } ++ ++ sg_miter_stop(&host->sg_miter); ++ ++ local_irq_restore(flags); ++} ++ ++ ++static void bcm2835_mmc_transfer_pio(struct bcm2835_host *host) ++{ ++ u32 mask; ++ ++ BUG_ON(!host->data); ++ ++ if (host->blocks == 0) ++ return; ++ ++ if (host->data->flags & MMC_DATA_READ) ++ mask = SDHCI_DATA_AVAILABLE; ++ else ++ mask = SDHCI_SPACE_AVAILABLE; ++ ++ while (bcm2835_mmc_readl(host, SDHCI_PRESENT_STATE) & mask) { ++ ++ if (host->data->flags & MMC_DATA_READ) ++ bcm2835_bcm2835_mmc_read_block_pio(host); ++ else ++ bcm2835_bcm2835_mmc_write_block_pio(host); ++ ++ host->blocks--; ++ ++ /* QUIRK used in sdhci.c removes the 'if' */ ++ /* but it seems this is unnecessary */ ++ if (host->blocks == 0) ++ break; ++ ++ ++ } ++} ++ ++ ++static void bcm2835_mmc_transfer_dma(struct bcm2835_host *host) ++{ ++ u32 len, dir_data, dir_slave; ++ struct dma_async_tx_descriptor *desc = NULL; ++ struct dma_chan *dma_chan; ++ ++ ++ WARN_ON(!host->data); ++ ++ if (!host->data) ++ return; ++ ++ if (host->blocks == 0) ++ return; ++ ++ dma_chan = host->dma_chan_rxtx; ++ if (host->data->flags & MMC_DATA_READ) { ++ dir_data = DMA_FROM_DEVICE; ++ dir_slave = DMA_DEV_TO_MEM; ++ } else { ++ dir_data = DMA_TO_DEVICE; ++ dir_slave = DMA_MEM_TO_DEV; ++ } ++ ++ /* The parameters have already been validated, so this will not fail */ ++ (void)dmaengine_slave_config(dma_chan, ++ (dir_data == DMA_FROM_DEVICE) ? ++ &host->dma_cfg_rx : ++ &host->dma_cfg_tx); ++ ++ BUG_ON(!dma_chan->device); ++ BUG_ON(!dma_chan->device->dev); ++ BUG_ON(!host->data->sg); ++ ++ len = dma_map_sg(dma_chan->device->dev, host->data->sg, ++ host->data->sg_len, dir_data); ++ if (len > 0) { ++ desc = dmaengine_prep_slave_sg(dma_chan, host->data->sg, ++ len, dir_slave, ++ DMA_PREP_INTERRUPT | DMA_CTRL_ACK); ++ } else { ++ dev_err(mmc_dev(host->mmc), "dma_map_sg returned zero length\n"); ++ } ++ if (desc) { ++ unsigned long flags; ++ spin_lock_irqsave(&host->lock, flags); ++ bcm2835_mmc_unsignal_irqs(host, SDHCI_INT_DATA_AVAIL | ++ SDHCI_INT_SPACE_AVAIL); ++ host->tx_desc = desc; ++ desc->callback = bcm2835_mmc_dma_complete; ++ desc->callback_param = host; ++ spin_unlock_irqrestore(&host->lock, flags); ++ dmaengine_submit(desc); ++ dma_async_issue_pending(dma_chan); ++ } else { ++ dma_unmap_sg(dma_chan->device->dev, host->data->sg, len, dir_data); ++ } ++ ++} ++ ++ ++ ++static void bcm2835_mmc_set_transfer_irqs(struct bcm2835_host *host) ++{ ++ u32 pio_irqs = SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL; ++ u32 dma_irqs = SDHCI_INT_DMA_END | SDHCI_INT_ADMA_ERROR; ++ ++ if (host->use_dma) ++ host->ier = (host->ier & ~pio_irqs) | dma_irqs; ++ else ++ host->ier = (host->ier & ~dma_irqs) | pio_irqs; ++ ++ bcm2835_mmc_writel(host, host->ier, SDHCI_INT_ENABLE, 4); ++ bcm2835_mmc_writel(host, host->ier, SDHCI_SIGNAL_ENABLE, 4); ++} ++ ++ ++static void bcm2835_mmc_prepare_data(struct bcm2835_host *host, struct mmc_command *cmd) ++{ ++ u8 count; ++ struct mmc_data *data = cmd->data; ++ ++ WARN_ON(host->data); ++ ++ if (data || (cmd->flags & MMC_RSP_BUSY)) { ++ count = TIMEOUT_VAL; ++ bcm2835_mmc_writeb(host, count, SDHCI_TIMEOUT_CONTROL); ++ } ++ ++ if (!data) ++ return; ++ ++ /* Sanity checks */ ++ BUG_ON(data->blksz * data->blocks > 524288); ++ BUG_ON(data->blksz > host->mmc->max_blk_size); ++ BUG_ON(data->blocks > 65535); ++ ++ host->data = data; ++ host->data_early = 0; ++ host->data->bytes_xfered = 0; ++ ++ ++ if (!(host->flags & SDHCI_REQ_USE_DMA)) { ++ int flags; ++ ++ flags = SG_MITER_ATOMIC; ++ if (host->data->flags & MMC_DATA_READ) ++ flags |= SG_MITER_TO_SG; ++ else ++ flags |= SG_MITER_FROM_SG; ++ sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags); ++ host->blocks = data->blocks; ++ } ++ ++ host->use_dma = host->have_dma && data->blocks > PIO_DMA_BARRIER; ++ ++ bcm2835_mmc_set_transfer_irqs(host); ++ ++ /* Set the DMA boundary value and block size */ ++ bcm2835_mmc_writew(host, SDHCI_MAKE_BLKSZ(SDHCI_DEFAULT_BOUNDARY_ARG, ++ data->blksz), SDHCI_BLOCK_SIZE); ++ bcm2835_mmc_writew(host, data->blocks, SDHCI_BLOCK_COUNT); ++ ++ BUG_ON(!host->data); ++} ++ ++static void bcm2835_mmc_set_transfer_mode(struct bcm2835_host *host, ++ struct mmc_command *cmd) ++{ ++ u16 mode; ++ struct mmc_data *data = cmd->data; ++ ++ if (data == NULL) { ++ /* clear Auto CMD settings for no data CMDs */ ++ mode = bcm2835_mmc_readw(host, SDHCI_TRANSFER_MODE); ++ bcm2835_mmc_writew(host, mode & ~(SDHCI_TRNS_AUTO_CMD12 | ++ SDHCI_TRNS_AUTO_CMD23), SDHCI_TRANSFER_MODE); ++ return; ++ } ++ ++ WARN_ON(!host->data); ++ ++ mode = SDHCI_TRNS_BLK_CNT_EN; ++ ++ if ((mmc_op_multi(cmd->opcode) || data->blocks > 1)) { ++ mode |= SDHCI_TRNS_MULTI; ++ ++ /* ++ * If we are sending CMD23, CMD12 never gets sent ++ * on successful completion (so no Auto-CMD12). ++ */ ++ if (!host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD12)) ++ mode |= SDHCI_TRNS_AUTO_CMD12; ++ else if (host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) { ++ mode |= SDHCI_TRNS_AUTO_CMD23; ++ bcm2835_mmc_writel(host, host->mrq->sbc->arg, SDHCI_ARGUMENT2, 5); ++ } ++ } ++ ++ if (data->flags & MMC_DATA_READ) ++ mode |= SDHCI_TRNS_READ; ++ if (host->flags & SDHCI_REQ_USE_DMA) ++ mode |= SDHCI_TRNS_DMA; ++ ++ bcm2835_mmc_writew(host, mode, SDHCI_TRANSFER_MODE); ++} ++ ++void bcm2835_mmc_send_command(struct bcm2835_host *host, struct mmc_command *cmd) ++{ ++ int flags; ++ u32 mask; ++ unsigned long timeout; ++ ++ WARN_ON(host->cmd); ++ ++ /* Wait max 10 ms */ ++ timeout = 1000; ++ ++ mask = SDHCI_CMD_INHIBIT; ++ if ((cmd->data != NULL) || (cmd->flags & MMC_RSP_BUSY)) ++ mask |= SDHCI_DATA_INHIBIT; ++ ++ /* We shouldn't wait for data inihibit for stop commands, even ++ though they might use busy signaling */ ++ if (host->mrq->data && (cmd == host->mrq->data->stop)) ++ mask &= ~SDHCI_DATA_INHIBIT; ++ ++ while (bcm2835_mmc_readl(host, SDHCI_PRESENT_STATE) & mask) { ++ if (timeout == 0) { ++ pr_err("%s: Controller never released inhibit bit(s).\n", ++ mmc_hostname(host->mmc)); ++ bcm2835_mmc_dumpregs(host); ++ cmd->error = -EIO; ++ tasklet_schedule(&host->finish_tasklet); ++ return; ++ } ++ timeout--; ++ udelay(10); ++ } ++ ++ if ((1000-timeout)/100 > 1 && (1000-timeout)/100 > host->max_delay) { ++ host->max_delay = (1000-timeout)/100; ++ pr_warn("Warning: MMC controller hung for %d ms\n", host->max_delay); ++ } ++ ++ timeout = jiffies; ++ if (!cmd->data && cmd->busy_timeout > 9000) ++ timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ; ++ else ++ timeout += 10 * HZ; ++ mod_timer(&host->timer, timeout); ++ ++ host->cmd = cmd; ++ host->use_dma = false; ++ ++ bcm2835_mmc_prepare_data(host, cmd); ++ ++ bcm2835_mmc_writel(host, cmd->arg, SDHCI_ARGUMENT, 6); ++ ++ bcm2835_mmc_set_transfer_mode(host, cmd); ++ ++ if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) { ++ pr_err("%s: Unsupported response type!\n", ++ mmc_hostname(host->mmc)); ++ cmd->error = -EINVAL; ++ tasklet_schedule(&host->finish_tasklet); ++ return; ++ } ++ ++ if (!(cmd->flags & MMC_RSP_PRESENT)) ++ flags = SDHCI_CMD_RESP_NONE; ++ else if (cmd->flags & MMC_RSP_136) ++ flags = SDHCI_CMD_RESP_LONG; ++ else if (cmd->flags & MMC_RSP_BUSY) ++ flags = SDHCI_CMD_RESP_SHORT_BUSY; ++ else ++ flags = SDHCI_CMD_RESP_SHORT; ++ ++ if (cmd->flags & MMC_RSP_CRC) ++ flags |= SDHCI_CMD_CRC; ++ if (cmd->flags & MMC_RSP_OPCODE) ++ flags |= SDHCI_CMD_INDEX; ++ ++ if (cmd->data) ++ flags |= SDHCI_CMD_DATA; ++ ++ bcm2835_mmc_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND); ++} ++ ++ ++static void bcm2835_mmc_finish_data(struct bcm2835_host *host) ++{ ++ struct mmc_data *data; ++ ++ BUG_ON(!host->data); ++ ++ data = host->data; ++ host->data = NULL; ++ ++ if (data->error) ++ data->bytes_xfered = 0; ++ else ++ data->bytes_xfered = data->blksz * data->blocks; ++ ++ /* ++ * Need to send CMD12 if - ++ * a) open-ended multiblock transfer (no CMD23) ++ * b) error in multiblock transfer ++ */ ++ if (data->stop && ++ (data->error || ++ !host->mrq->sbc)) { ++ ++ /* ++ * The controller needs a reset of internal state machines ++ * upon error conditions. ++ */ ++ if (data->error) { ++ bcm2835_mmc_reset(host, SDHCI_RESET_CMD); ++ bcm2835_mmc_reset(host, SDHCI_RESET_DATA); ++ } ++ ++ bcm2835_mmc_send_command(host, data->stop); ++ } else if (host->use_dma) { ++ host->wait_for_dma = true; ++ } else { ++ tasklet_schedule(&host->finish_tasklet); ++ } ++} ++ ++static void bcm2835_mmc_finish_command(struct bcm2835_host *host) ++{ ++ int i; ++ ++ BUG_ON(host->cmd == NULL); ++ ++ if (host->cmd->flags & MMC_RSP_PRESENT) { ++ if (host->cmd->flags & MMC_RSP_136) { ++ /* CRC is stripped so we need to do some shifting. */ ++ for (i = 0; i < 4; i++) { ++ host->cmd->resp[i] = bcm2835_mmc_readl(host, ++ SDHCI_RESPONSE + (3-i)*4) << 8; ++ if (i != 3) ++ host->cmd->resp[i] |= ++ bcm2835_mmc_readb(host, ++ SDHCI_RESPONSE + (3-i)*4-1); ++ } ++ } else { ++ host->cmd->resp[0] = bcm2835_mmc_readl(host, SDHCI_RESPONSE); ++ } ++ } ++ ++ host->cmd->error = 0; ++ ++ /* Finished CMD23, now send actual command. */ ++ if (host->cmd == host->mrq->sbc) { ++ host->cmd = NULL; ++ bcm2835_mmc_send_command(host, host->mrq->cmd); ++ ++ if (host->mrq->cmd->data && host->use_dma) { ++ /* DMA transfer starts now, PIO starts after interrupt */ ++ bcm2835_mmc_transfer_dma(host); ++ } ++ } else { ++ ++ /* Processed actual command. */ ++ if (host->data && host->data_early) ++ bcm2835_mmc_finish_data(host); ++ ++ if (!host->cmd->data) ++ tasklet_schedule(&host->finish_tasklet); ++ ++ host->cmd = NULL; ++ } ++} ++ ++ ++static void bcm2835_mmc_timeout_timer(struct timer_list *t) ++{ ++ struct bcm2835_host *host = from_timer(host, t, timer); ++ unsigned long flags; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ if (host->mrq) { ++ pr_err("%s: Timeout waiting for hardware interrupt.\n", ++ mmc_hostname(host->mmc)); ++ bcm2835_mmc_dumpregs(host); ++ ++ if (host->data) { ++ host->data->error = -ETIMEDOUT; ++ bcm2835_mmc_finish_data(host); ++ } else { ++ if (host->cmd) ++ host->cmd->error = -ETIMEDOUT; ++ else ++ host->mrq->cmd->error = -ETIMEDOUT; ++ ++ tasklet_schedule(&host->finish_tasklet); ++ } ++ } ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++ ++static void bcm2835_mmc_enable_sdio_irq_nolock(struct bcm2835_host *host, int enable) ++{ ++ if (!(host->flags & SDHCI_DEVICE_DEAD)) { ++ if (enable) ++ host->ier |= SDHCI_INT_CARD_INT; ++ else ++ host->ier &= ~SDHCI_INT_CARD_INT; ++ ++ bcm2835_mmc_writel(host, host->ier, SDHCI_INT_ENABLE, 7); ++ bcm2835_mmc_writel(host, host->ier, SDHCI_SIGNAL_ENABLE, 7); ++ } ++} ++ ++static void bcm2835_mmc_enable_sdio_irq(struct mmc_host *mmc, int enable) ++{ ++ struct bcm2835_host *host = mmc_priv(mmc); ++ unsigned long flags; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ if (enable) ++ host->flags |= SDHCI_SDIO_IRQ_ENABLED; ++ else ++ host->flags &= ~SDHCI_SDIO_IRQ_ENABLED; ++ ++ bcm2835_mmc_enable_sdio_irq_nolock(host, enable); ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static void bcm2835_mmc_cmd_irq(struct bcm2835_host *host, u32 intmask) ++{ ++ ++ BUG_ON(intmask == 0); ++ ++ if (!host->cmd) { ++ pr_err("%s: Got command interrupt 0x%08x even " ++ "though no command operation was in progress.\n", ++ mmc_hostname(host->mmc), (unsigned)intmask); ++ bcm2835_mmc_dumpregs(host); ++ return; ++ } ++ ++ if (intmask & SDHCI_INT_TIMEOUT) ++ host->cmd->error = -ETIMEDOUT; ++ else if (intmask & (SDHCI_INT_CRC | SDHCI_INT_END_BIT | ++ SDHCI_INT_INDEX)) { ++ host->cmd->error = -EILSEQ; ++ } ++ ++ if (host->cmd->error) { ++ tasklet_schedule(&host->finish_tasklet); ++ return; ++ } ++ ++ if (intmask & SDHCI_INT_RESPONSE) ++ bcm2835_mmc_finish_command(host); ++ ++} ++ ++static void bcm2835_mmc_data_irq(struct bcm2835_host *host, u32 intmask) ++{ ++ struct dma_chan *dma_chan; ++ u32 dir_data; ++ ++ BUG_ON(intmask == 0); ++ ++ if (!host->data) { ++ /* ++ * The "data complete" interrupt is also used to ++ * indicate that a busy state has ended. See comment ++ * above in sdhci_cmd_irq(). ++ */ ++ if (host->cmd && (host->cmd->flags & MMC_RSP_BUSY)) { ++ if (intmask & SDHCI_INT_DATA_END) { ++ bcm2835_mmc_finish_command(host); ++ return; ++ } ++ } ++ ++ pr_debug("%s: Got data interrupt 0x%08x even " ++ "though no data operation was in progress.\n", ++ mmc_hostname(host->mmc), (unsigned)intmask); ++ bcm2835_mmc_dumpregs(host); ++ ++ return; ++ } ++ ++ if (intmask & SDHCI_INT_DATA_TIMEOUT) ++ host->data->error = -ETIMEDOUT; ++ else if (intmask & SDHCI_INT_DATA_END_BIT) ++ host->data->error = -EILSEQ; ++ else if ((intmask & SDHCI_INT_DATA_CRC) && ++ SDHCI_GET_CMD(bcm2835_mmc_readw(host, SDHCI_COMMAND)) ++ != MMC_BUS_TEST_R) ++ host->data->error = -EILSEQ; ++ ++ if (host->use_dma) { ++ if (host->data->flags & MMC_DATA_WRITE) { ++ /* IRQ handled here */ ++ ++ dma_chan = host->dma_chan_rxtx; ++ dir_data = DMA_TO_DEVICE; ++ dma_unmap_sg(dma_chan->device->dev, ++ host->data->sg, host->data->sg_len, ++ dir_data); ++ ++ bcm2835_mmc_finish_data(host); ++ } ++ ++ } else { ++ if (host->data->error) ++ bcm2835_mmc_finish_data(host); ++ else { ++ if (intmask & (SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL)) ++ bcm2835_mmc_transfer_pio(host); ++ ++ if (intmask & SDHCI_INT_DATA_END) { ++ if (host->cmd) { ++ /* ++ * Data managed to finish before the ++ * command completed. Make sure we do ++ * things in the proper order. ++ */ ++ host->data_early = 1; ++ } else { ++ bcm2835_mmc_finish_data(host); ++ } ++ } ++ } ++ } ++} ++ ++ ++static irqreturn_t bcm2835_mmc_irq(int irq, void *dev_id) ++{ ++ irqreturn_t result = IRQ_NONE; ++ struct bcm2835_host *host = dev_id; ++ u32 intmask, mask, unexpected = 0; ++ int max_loops = 16; ++ ++ spin_lock(&host->lock); ++ ++ intmask = bcm2835_mmc_readl(host, SDHCI_INT_STATUS); ++ ++ if (!intmask || intmask == 0xffffffff) { ++ result = IRQ_NONE; ++ goto out; ++ } ++ ++ do { ++ /* Clear selected interrupts. */ ++ mask = intmask & (SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK | ++ SDHCI_INT_BUS_POWER); ++ bcm2835_mmc_writel(host, mask, SDHCI_INT_STATUS, 8); ++ ++ ++ if (intmask & SDHCI_INT_CMD_MASK) ++ bcm2835_mmc_cmd_irq(host, intmask & SDHCI_INT_CMD_MASK); ++ ++ if (intmask & SDHCI_INT_DATA_MASK) ++ bcm2835_mmc_data_irq(host, intmask & SDHCI_INT_DATA_MASK); ++ ++ if (intmask & SDHCI_INT_BUS_POWER) ++ pr_err("%s: Card is consuming too much power!\n", ++ mmc_hostname(host->mmc)); ++ ++ if (intmask & SDHCI_INT_CARD_INT) { ++ bcm2835_mmc_enable_sdio_irq_nolock(host, false); ++ sdio_signal_irq(host->mmc); ++ } ++ ++ intmask &= ~(SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE | ++ SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK | ++ SDHCI_INT_ERROR | SDHCI_INT_BUS_POWER | ++ SDHCI_INT_CARD_INT); ++ ++ if (intmask) { ++ unexpected |= intmask; ++ bcm2835_mmc_writel(host, intmask, SDHCI_INT_STATUS, 9); ++ } ++ ++ if (result == IRQ_NONE) ++ result = IRQ_HANDLED; ++ ++ intmask = bcm2835_mmc_readl(host, SDHCI_INT_STATUS); ++ } while (intmask && --max_loops); ++out: ++ spin_unlock(&host->lock); ++ ++ if (unexpected) { ++ pr_err("%s: Unexpected interrupt 0x%08x.\n", ++ mmc_hostname(host->mmc), unexpected); ++ bcm2835_mmc_dumpregs(host); ++ } ++ ++ return result; ++} ++ ++ ++static void bcm2835_mmc_ack_sdio_irq(struct mmc_host *mmc) ++{ ++ struct bcm2835_host *host = mmc_priv(mmc); ++ unsigned long flags; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ if (host->flags & SDHCI_SDIO_IRQ_ENABLED) ++ bcm2835_mmc_enable_sdio_irq_nolock(host, true); ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++void bcm2835_mmc_set_clock(struct bcm2835_host *host, unsigned int clock) ++{ ++ int div = 0; /* Initialized for compiler warning */ ++ int real_div = div, clk_mul = 1; ++ u16 clk = 0; ++ unsigned long timeout; ++ unsigned int input_clock = clock; ++ ++ if (host->overclock_50 && (clock == 50000000)) ++ clock = host->overclock_50 * 1000000 + 999999; ++ ++ host->mmc->actual_clock = 0; ++ ++ bcm2835_mmc_writew(host, 0, SDHCI_CLOCK_CONTROL); ++ ++ if (clock == 0) ++ return; ++ ++ /* Version 3.00 divisors must be a multiple of 2. */ ++ if (host->max_clk <= clock) ++ div = 1; ++ else { ++ for (div = 2; div < SDHCI_MAX_DIV_SPEC_300; ++ div += 2) { ++ if ((host->max_clk / div) <= clock) ++ break; ++ } ++ } ++ ++ real_div = div; ++ div >>= 1; ++ ++ if (real_div) ++ clock = (host->max_clk * clk_mul) / real_div; ++ host->mmc->actual_clock = clock; ++ ++ if ((clock > input_clock) && (clock > host->max_overclock)) { ++ pr_warn("%s: Overclocking to %dHz\n", ++ mmc_hostname(host->mmc), clock); ++ host->max_overclock = clock; ++ } ++ ++ clk |= (div & SDHCI_DIV_MASK) << SDHCI_DIVIDER_SHIFT; ++ clk |= ((div & SDHCI_DIV_HI_MASK) >> SDHCI_DIV_MASK_LEN) ++ << SDHCI_DIVIDER_HI_SHIFT; ++ clk |= SDHCI_CLOCK_INT_EN; ++ bcm2835_mmc_writew(host, clk, SDHCI_CLOCK_CONTROL); ++ ++ /* Wait max 20 ms */ ++ timeout = 20; ++ while (!((clk = bcm2835_mmc_readw(host, SDHCI_CLOCK_CONTROL)) ++ & SDHCI_CLOCK_INT_STABLE)) { ++ if (timeout == 0) { ++ pr_err("%s: Internal clock never " ++ "stabilised.\n", mmc_hostname(host->mmc)); ++ bcm2835_mmc_dumpregs(host); ++ return; ++ } ++ timeout--; ++ mdelay(1); ++ } ++ ++ if (20-timeout > 10 && 20-timeout > host->max_delay) { ++ host->max_delay = 20-timeout; ++ pr_warn("Warning: MMC controller hung for %d ms\n", host->max_delay); ++ } ++ ++ clk |= SDHCI_CLOCK_CARD_EN; ++ bcm2835_mmc_writew(host, clk, SDHCI_CLOCK_CONTROL); ++} ++ ++static void bcm2835_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq) ++{ ++ struct bcm2835_host *host; ++ unsigned long flags; ++ ++ host = mmc_priv(mmc); ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ WARN_ON(host->mrq != NULL); ++ ++ host->mrq = mrq; ++ ++ if (mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23)) ++ bcm2835_mmc_send_command(host, mrq->sbc); ++ else ++ bcm2835_mmc_send_command(host, mrq->cmd); ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++ ++ if (!(mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23)) && mrq->cmd->data && host->use_dma) { ++ /* DMA transfer starts now, PIO starts after interrupt */ ++ bcm2835_mmc_transfer_dma(host); ++ } ++} ++ ++ ++static void bcm2835_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) ++{ ++ ++ struct bcm2835_host *host = mmc_priv(mmc); ++ unsigned long flags; ++ u8 ctrl; ++ u16 clk, ctrl_2; ++ ++ pr_debug("bcm2835_mmc_set_ios: clock %d, pwr %d, bus_width %d, timing %d, vdd %d, drv_type %d\n", ++ ios->clock, ios->power_mode, ios->bus_width, ++ ios->timing, ios->signal_voltage, ios->drv_type); ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ if (!ios->clock || ios->clock != host->clock) { ++ bcm2835_mmc_set_clock(host, ios->clock); ++ host->clock = ios->clock; ++ } ++ ++ if (host->pwr != SDHCI_POWER_330) { ++ host->pwr = SDHCI_POWER_330; ++ bcm2835_mmc_writeb(host, SDHCI_POWER_330 | SDHCI_POWER_ON, SDHCI_POWER_CONTROL); ++ } ++ ++ ctrl = bcm2835_mmc_readb(host, SDHCI_HOST_CONTROL); ++ ++ /* set bus width */ ++ ctrl &= ~SDHCI_CTRL_8BITBUS; ++ if (ios->bus_width == MMC_BUS_WIDTH_4) ++ ctrl |= SDHCI_CTRL_4BITBUS; ++ else ++ ctrl &= ~SDHCI_CTRL_4BITBUS; ++ ++ ctrl &= ~SDHCI_CTRL_HISPD; /* NO_HISPD_BIT */ ++ ++ ++ bcm2835_mmc_writeb(host, ctrl, SDHCI_HOST_CONTROL); ++ /* ++ * We only need to set Driver Strength if the ++ * preset value enable is not set. ++ */ ++ ctrl_2 = bcm2835_mmc_readw(host, SDHCI_HOST_CONTROL2); ++ ctrl_2 &= ~SDHCI_CTRL_DRV_TYPE_MASK; ++ if (ios->drv_type == MMC_SET_DRIVER_TYPE_A) ++ ctrl_2 |= SDHCI_CTRL_DRV_TYPE_A; ++ else if (ios->drv_type == MMC_SET_DRIVER_TYPE_C) ++ ctrl_2 |= SDHCI_CTRL_DRV_TYPE_C; ++ ++ bcm2835_mmc_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); ++ ++ /* Reset SD Clock Enable */ ++ clk = bcm2835_mmc_readw(host, SDHCI_CLOCK_CONTROL); ++ clk &= ~SDHCI_CLOCK_CARD_EN; ++ bcm2835_mmc_writew(host, clk, SDHCI_CLOCK_CONTROL); ++ ++ /* Re-enable SD Clock */ ++ bcm2835_mmc_set_clock(host, host->clock); ++ bcm2835_mmc_writeb(host, ctrl, SDHCI_HOST_CONTROL); ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++ ++static struct mmc_host_ops bcm2835_ops = { ++ .request = bcm2835_mmc_request, ++ .set_ios = bcm2835_mmc_set_ios, ++ .enable_sdio_irq = bcm2835_mmc_enable_sdio_irq, ++ .ack_sdio_irq = bcm2835_mmc_ack_sdio_irq, ++}; ++ ++ ++static void bcm2835_mmc_tasklet_finish(unsigned long param) ++{ ++ struct bcm2835_host *host; ++ unsigned long flags; ++ struct mmc_request *mrq; ++ ++ host = (struct bcm2835_host *)param; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ /* ++ * If this tasklet gets rescheduled while running, it will ++ * be run again afterwards but without any active request. ++ */ ++ if (!host->mrq) { ++ spin_unlock_irqrestore(&host->lock, flags); ++ return; ++ } ++ ++ del_timer(&host->timer); ++ ++ mrq = host->mrq; ++ ++ /* ++ * The controller needs a reset of internal state machines ++ * upon error conditions. ++ */ ++ if (!(host->flags & SDHCI_DEVICE_DEAD) && ++ ((mrq->cmd && mrq->cmd->error) || ++ (mrq->data && (mrq->data->error || ++ (mrq->data->stop && mrq->data->stop->error))))) { ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++ bcm2835_mmc_reset(host, SDHCI_RESET_CMD); ++ bcm2835_mmc_reset(host, SDHCI_RESET_DATA); ++ spin_lock_irqsave(&host->lock, flags); ++ } ++ ++ host->mrq = NULL; ++ host->cmd = NULL; ++ host->data = NULL; ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++ mmc_request_done(host->mmc, mrq); ++} ++ ++ ++ ++static int bcm2835_mmc_add_host(struct bcm2835_host *host) ++{ ++ struct mmc_host *mmc = host->mmc; ++ struct device *dev = mmc->parent; ++#ifndef FORCE_PIO ++ struct dma_slave_config cfg; ++#endif ++ int ret; ++ ++ bcm2835_mmc_reset(host, SDHCI_RESET_ALL); ++ ++ host->clk_mul = 0; ++ ++ if (!mmc->f_max || mmc->f_max > host->max_clk) ++ mmc->f_max = host->max_clk; ++ mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_300; ++ ++ /* SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK */ ++ host->timeout_clk = mmc->f_max / 1000; ++ mmc->max_busy_timeout = (1 << 27) / host->timeout_clk; ++ ++ /* host controller capabilities */ ++ mmc->caps |= MMC_CAP_CMD23 | MMC_CAP_NEEDS_POLL | ++ MMC_CAP_SDIO_IRQ | MMC_CAP_SD_HIGHSPEED | ++ MMC_CAP_MMC_HIGHSPEED; ++ ++ mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD; ++ ++ host->flags = SDHCI_AUTO_CMD23; ++ ++ dev_info(dev, "mmc_debug:%x mmc_debug2:%x\n", mmc_debug, mmc_debug2); ++#ifdef FORCE_PIO ++ dev_info(dev, "Forcing PIO mode\n"); ++ host->have_dma = false; ++#else ++ if (IS_ERR_OR_NULL(host->dma_chan_rxtx)) { ++ dev_err(dev, "%s: Unable to initialise DMA channel. Falling back to PIO\n", ++ DRIVER_NAME); ++ host->have_dma = false; ++ } else { ++ dev_info(dev, "DMA channel allocated"); ++ ++ cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; ++ cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; ++ cfg.slave_id = 11; /* DREQ channel */ ++ ++ /* Validate the slave configurations */ ++ ++ cfg.direction = DMA_MEM_TO_DEV; ++ cfg.src_addr = 0; ++ cfg.dst_addr = host->bus_addr + SDHCI_BUFFER; ++ ++ ret = dmaengine_slave_config(host->dma_chan_rxtx, &cfg); ++ ++ if (ret == 0) { ++ host->dma_cfg_tx = cfg; ++ ++ cfg.direction = DMA_DEV_TO_MEM; ++ cfg.src_addr = host->bus_addr + SDHCI_BUFFER; ++ cfg.dst_addr = 0; ++ ++ ret = dmaengine_slave_config(host->dma_chan_rxtx, &cfg); ++ } ++ ++ if (ret == 0) { ++ host->dma_cfg_rx = cfg; ++ ++ host->have_dma = true; ++ } else { ++ pr_err("%s: unable to configure DMA channel. " ++ "Falling back to PIO\n", ++ mmc_hostname(mmc)); ++ dma_release_channel(host->dma_chan_rxtx); ++ host->dma_chan_rxtx = NULL; ++ host->have_dma = false; ++ } ++ } ++#endif ++ mmc->max_segs = 128; ++ if (swiotlb_max_segment()) ++ mmc->max_req_size = (1 << IO_TLB_SHIFT) * IO_TLB_SEGSIZE; ++ else ++ mmc->max_req_size = 524288; ++ mmc->max_seg_size = mmc->max_req_size; ++ mmc->max_blk_size = 512; ++ mmc->max_blk_count = 65535; ++ ++ /* report supported voltage ranges */ ++ mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; ++ ++ tasklet_init(&host->finish_tasklet, ++ bcm2835_mmc_tasklet_finish, (unsigned long)host); ++ ++ timer_setup(&host->timer, bcm2835_mmc_timeout_timer, 0); ++ init_waitqueue_head(&host->buf_ready_int); ++ ++ bcm2835_mmc_init(host, 0); ++ ret = request_irq(host->irq, bcm2835_mmc_irq, IRQF_SHARED, ++ mmc_hostname(mmc), host); ++ if (ret) { ++ dev_err(dev, "Failed to request IRQ %d: %d\n", host->irq, ret); ++ goto untasklet; ++ } ++ ++ ret = mmc_add_host(mmc); ++ if (ret) { ++ dev_err(dev, "could not add MMC host\n"); ++ goto free_irq; ++ } ++ ++ return 0; ++ ++free_irq: ++ free_irq(host->irq, host); ++untasklet: ++ tasklet_kill(&host->finish_tasklet); ++ ++ return ret; ++} ++ ++static int bcm2835_mmc_probe(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ struct device_node *node = dev->of_node; ++ struct clk *clk; ++ struct resource *iomem; ++ struct bcm2835_host *host; ++ struct mmc_host *mmc; ++ const __be32 *addr; ++ int ret; ++ ++ mmc = mmc_alloc_host(sizeof(*host), dev); ++ if (!mmc) ++ return -ENOMEM; ++ ++ mmc->ops = &bcm2835_ops; ++ host = mmc_priv(mmc); ++ host->mmc = mmc; ++ host->timeout = msecs_to_jiffies(1000); ++ spin_lock_init(&host->lock); ++ ++ iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ host->ioaddr = devm_ioremap_resource(dev, iomem); ++ if (IS_ERR(host->ioaddr)) { ++ ret = PTR_ERR(host->ioaddr); ++ goto err; ++ } ++ ++ addr = of_get_address(node, 0, NULL, NULL); ++ if (!addr) { ++ dev_err(dev, "could not get DMA-register address\n"); ++ ret = -ENODEV; ++ goto err; ++ } ++ host->bus_addr = be32_to_cpup(addr); ++ pr_debug(" - ioaddr %lx, iomem->start %lx, bus_addr %lx\n", ++ (unsigned long)host->ioaddr, ++ (unsigned long)iomem->start, ++ (unsigned long)host->bus_addr); ++ ++#ifndef FORCE_PIO ++ if (node) { ++ host->dma_chan_rxtx = dma_request_slave_channel(dev, "rx-tx"); ++ if (!host->dma_chan_rxtx) ++ host->dma_chan_rxtx = ++ dma_request_slave_channel(dev, "tx"); ++ if (!host->dma_chan_rxtx) ++ host->dma_chan_rxtx = ++ dma_request_slave_channel(dev, "rx"); ++ } else { ++ dma_cap_mask_t mask; ++ ++ dma_cap_zero(mask); ++ /* we don't care about the channel, any would work */ ++ dma_cap_set(DMA_SLAVE, mask); ++ host->dma_chan_rxtx = dma_request_channel(mask, NULL, NULL); ++ } ++#endif ++ clk = devm_clk_get(dev, NULL); ++ if (IS_ERR(clk)) { ++ ret = PTR_ERR(clk); ++ if (ret == -EPROBE_DEFER) ++ dev_info(dev, "could not get clk, deferring probe\n"); ++ else ++ dev_err(dev, "could not get clk\n"); ++ goto err; ++ } ++ ++ host->max_clk = clk_get_rate(clk); ++ ++ host->irq = platform_get_irq(pdev, 0); ++ if (host->irq <= 0) { ++ dev_err(dev, "get IRQ failed\n"); ++ ret = -EINVAL; ++ goto err; ++ } ++ ++ if (node) { ++ mmc_of_parse(mmc); ++ ++ /* Read any custom properties */ ++ of_property_read_u32(node, ++ "brcm,overclock-50", ++ &host->overclock_50); ++ } else { ++ mmc->caps |= MMC_CAP_4_BIT_DATA; ++ } ++ ++ ret = bcm2835_mmc_add_host(host); ++ if (ret) ++ goto err; ++ ++ platform_set_drvdata(pdev, host); ++ ++ return 0; ++err: ++ if (host->dma_chan_rxtx) ++ dma_release_channel(host->dma_chan_rxtx); ++ mmc_free_host(mmc); ++ ++ return ret; ++} ++ ++static int bcm2835_mmc_remove(struct platform_device *pdev) ++{ ++ struct bcm2835_host *host = platform_get_drvdata(pdev); ++ unsigned long flags; ++ int dead; ++ u32 scratch; ++ ++ dead = 0; ++ scratch = bcm2835_mmc_readl(host, SDHCI_INT_STATUS); ++ if (scratch == (u32)-1) ++ dead = 1; ++ ++ ++ if (dead) { ++ spin_lock_irqsave(&host->lock, flags); ++ ++ host->flags |= SDHCI_DEVICE_DEAD; ++ ++ if (host->mrq) { ++ pr_err("%s: Controller removed during " ++ " transfer!\n", mmc_hostname(host->mmc)); ++ ++ host->mrq->cmd->error = -ENOMEDIUM; ++ tasklet_schedule(&host->finish_tasklet); ++ } ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++ } ++ ++ mmc_remove_host(host->mmc); ++ ++ if (!dead) ++ bcm2835_mmc_reset(host, SDHCI_RESET_ALL); ++ ++ free_irq(host->irq, host); ++ ++ del_timer_sync(&host->timer); ++ ++ tasklet_kill(&host->finish_tasklet); ++ ++ if (host->dma_chan_rxtx) ++ dma_release_channel(host->dma_chan_rxtx); ++ ++ mmc_free_host(host->mmc); ++ ++ return 0; ++} ++ ++ ++static const struct of_device_id bcm2835_mmc_match[] = { ++ { .compatible = "brcm,bcm2835-mmc" }, ++ { } ++}; ++MODULE_DEVICE_TABLE(of, bcm2835_mmc_match); ++ ++ ++ ++static struct platform_driver bcm2835_mmc_driver = { ++ .probe = bcm2835_mmc_probe, ++ .remove = bcm2835_mmc_remove, ++ .driver = { ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ .of_match_table = bcm2835_mmc_match, ++ }, ++}; ++module_platform_driver(bcm2835_mmc_driver); ++ ++module_param(mmc_debug, uint, 0644); ++module_param(mmc_debug2, uint, 0644); ++MODULE_ALIAS("platform:mmc-bcm2835"); ++MODULE_DESCRIPTION("BCM2835 SDHCI driver"); ++MODULE_LICENSE("GPL v2"); ++MODULE_AUTHOR("Gellert Weisz"); +--- a/include/linux/mmc/card.h ++++ b/include/linux/mmc/card.h +@@ -271,6 +271,8 @@ struct mmc_card { + #define MMC_QUIRK_TRIM_BROKEN (1<<12) /* Skip trim */ + #define MMC_QUIRK_BROKEN_HPI (1<<13) /* Disable broken HPI support */ + ++#define MMC_QUIRK_ERASE_BROKEN (1<<31) /* Skip erase */ ++ + bool reenable_cmdq; /* Re-enable Command Queue */ + + unsigned int erase_size; /* erase size in sectors */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0047-Adding-bcm2835-sdhost-driver-and-an-overlay-to-enabl.patch b/target/linux/bcm27xx/patches-5.10/950-0047-Adding-bcm2835-sdhost-driver-and-an-overlay-to-enabl.patch new file mode 100644 index 0000000000..b98833ef24 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0047-Adding-bcm2835-sdhost-driver-and-an-overlay-to-enabl.patch @@ -0,0 +1,2481 @@ +From dd8b26a3df74f3022a6ddc794049a08d7190be3a Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 25 Mar 2015 17:49:47 +0000 +Subject: [PATCH] Adding bcm2835-sdhost driver, and an overlay to + enable it + +BCM2835 has two SD card interfaces. This driver uses the other one. + +bcm2835-sdhost: Error handling fix, and code clarification + +bcm2835-sdhost: Adding overclocking option + +Allow a different clock speed to be substitued for a requested 50MHz. +This option is exposed using the "overclock_50" DT parameter. +Note that the sdhost interface is restricted to integer divisions of +core_freq, and the highest sensible option for a core_freq of 250MHz +is 84 (250/3 = 83.3MHz), the next being 125 (250/2) which is much too +high. + +Use at your own risk. + +bcm2835-sdhost: Round up the overclock, so 62 works for 62.5Mhz + +Also only warn once for each overclock setting. + +bcm2835-sdhost: Improve error handling and recovery + +1) Expose the hw_reset method to the MMC framework, removing many + internal calls by the driver. + +2) Reduce overclock setting on error. + +3) Increase timeout to cope with high capacity cards. + +4) Add properties and parameters to control pio_limit and debug. + +5) Reduce messages at probe time. + +bcm2835-sdhost: Further improve overclock back-off + +bcm2835-sdhost: Clear HBLC for PIO mode + +Also update pio_limit default in overlay README. + +bcm2835-sdhost: Add the ERASE capability + +See: https://github.com/raspberrypi/linux/issues/1076 + +bcm2835-sdhost: Ignore CRC7 for MMC CMD1 + +It seems that the sdhost interface returns CRC7 errors for CMD1, +which is the MMC-specific SEND_OP_COND. Returning these errors to +the MMC layer causes a downward spiral, but ignoring them seems +to be harmless. + +bcm2835-mmc/sdhost: Remove ARCH_BCM2835 differences + +The bcm2835-mmc driver (and -sdhost driver that copied from it) +contains code to handle SDIO interrupts in a threaded interrupt +handler rather than waking the MMC framework thread. The change +follows a patch from Russell King that adds the facility as the +preferred way of working. + +However, the new code path is only present in ARCH_BCM2835 +builds, which I have taken to be a way of testing the waters +rather than making the change across the board; I can't see +any technical reason why it wouldn't be enabled for MACH_BCM270X +builds. So this patch standardises on the ARCH_BCM2835 code, +removing the old code paths. + +bcm2835-sdhost: Don't log timeout errors unless debug=1 + +The MMC card-discovery process generates timeouts. This is +expected behaviour, so reporting it to the user serves no purpose. +Suppress the reporting of timeout errors unless the debug flag +is on. + +bcm2835-sdhost: Add workaround for odd behaviour on some cards + +For reasons not understood, the sdhost driver fails when reading +sectors very near the end of some SD cards. The problem could +be related to the similar issue that reading the final sector +of any card as part of a multiple read never completes, and the +workaround is an extension of the mechanism introduced to solve +that problem which ensures those sectors are always read singly. + +bcm2835-sdhost: Major revision + +This is a significant revision of the bcm2835-sdhost driver. It +improves on the original in a number of ways: + +1) Through the use of CMD23 for reads it appears to avoid problems + reading some sectors on certain high speed cards. +2) Better atomicity to prevent crashes. +3) Higher performance. +4) Activity logging included, for easier diagnosis in the event + of a problem. + +Signed-off-by: Phil Elwell + +bcm2835-sdhost: Restore ATOMIC flag to PIO sg mapping + +Allocation problems have been seen in a wireless driver, and +this is the only change which might have been responsible. + +SQUASH: bcm2835-sdhost: Only claim one DMA channel + +With both MMC controllers enabled there are few DMA channels left. The +bcm2835-sdhost driver only uses DMA in one direction at a time, so it +doesn't need to claim two channels. + +See: https://github.com/raspberrypi/linux/issues/1327 + +Signed-off-by: Phil Elwell + +bcm2835-sdhost: Workaround for "slow" sectors + +Some cards have been seen to cause timeouts after certain sectors are +read. This workaround enforces a minimum delay between the stop after +reading one of those sectors and a subsequent data command. + +Using CMD23 (SET_BLOCK_COUNT) avoids this problem, so good cards will +not be penalised by this workaround. + +Signed-off-by: Phil Elwell + +bcm2835-sdhost: Firmware manages the clock divisor + +The bcm2835-sdhost driver hands control of the CDIV clock divisor +register to matching firmware, allowing it to adjust to a changing +core clock. This removes the need to use the performance governor or +to enable io_is_busy on the on-demand governor in order to get the +best SD performance. + +N.B. As SD clocks must be an integer divisor of the core clock, it is +possible that the SD clock for "turbo" mode can be different (even +lower) than "normal" mode. + +Signed-off-by: Phil Elwell + +bcm2835-sdhost: Reset the clock in task context + +Since reprogramming the clock can now involve a round-trip to the +firmware it must not be done at atomic context, and a tasklet +is not a task. + +Signed-off-by: Phil Elwell + +bcm2835-sdhost: Don't exit cmd wait loop on error + +The FAIL flag can be set in the CMD register before command processing +is complete, leading to spurious "failed to complete" errors. This has +the effect of promoting harmless CRC7 errors during CMD1 processing +into errors that can delay and even prevent booting. + +Also: +1) Convert the last KERN_ERROR message in the register dumping to + KERN_INFO. +2) Remove an unnecessary reset call from bcm2835_sdhost_add_host. + +See: https://github.com/raspberrypi/linux/pull/1492 + +Signed-off-by: Phil Elwell + +bcm2835-sdhost: mmc_card_blockaddr fix + +Get the definition of mmc_card_blockaddr from drivers/mmc/core/card.h. + +Signed-off-by: Phil Elwell + +bcm2835-sdhost: New timer API + +mmc: bcm2835-sdhost: Support underclocking + +Support underclocking of the SD bus in two ways: +1. using the max-frequency DT property (which currently has no DT + parameter), and +2. using the exiting sd_overclock parameter. + +The two methods differ slightly - in the former the MMC subsystem is +aware of the underclocking, while in the latter it isn't - but the +end results should be the same. + +See: https://github.com/raspberrypi/linux/issues/2350 + +Signed-off-by: Phil Elwell + +mmc: bcm2835-sdhost: Add include + +highmem.h (needed for kmap_atomic) is pulled in by one of the other +include files, but only with some CONFIG settings. Make the inclusion +explicit to cater for cases where the CONFIG setting is absent. + +See: https://github.com/raspberrypi/linux/issues/2366 + +Signed-off-by: Phil Elwell + +mmc/bcm2835-sdhost: Recover from MMC_SEND_EXT_CSD + +If the user issues an "mmc extcsd read", the SD controller receives +what it thinks is a SEND_IF_COND command with an unexpected data block. +The resulting operations leave the FSM stuck in READWAIT, a state which +persists until the MMC framework resets the controller, by which point +the root filesystem is likely to have been unmounted. + +A less heavyweight solution is to detect the condition and nudge the +FSM by asserting the (self-clearing) FORCE_DATA_MODE bit. + +N.B. This workaround was essentially discovered by accident and without +a full understanding the inner workings of the controller, so it is +fortunate that the "fix" only modifies error paths. + +See: https://github.com/raspberrypi/linux/issues/2728 + +Signed-off-by: Phil Elwell + +mmc: bcm2835-sdhost: Fix warnings on arm64 + +Signed-off-by: Phil Elwell + +bcm2835-sdhost: Allow for sg entries that cross pages + +The dma_complete handling code calculates a virtual address for a page +then adds an offset, but if the offset is more than a page and HIGHMEM +is in use then the summed address could be in an unmapped (or just +incorrect) page. + +The upstream SDHOST driver allows for this possibility - copy the code +that does so. + +Signed-off-by: Phil Elwell + +bcm2835-sdhost: Fix DMA channel leak on error/remove + +Signed-off-by: Phil Elwell + +mmc: bcm2835-sdhost: Support 64-bit physical addresses + +Signed-off-by: Phil Elwell + +bcm2835-sdhost: Replace obsolete struct timeval + +struct timeval has been retired due to the impending linux 32-bit tv_sec +rollover (only 18 years to go) - timespec64 is the obvious replacement. + +Signed-off-by: Phil Elwell +--- + drivers/mmc/host/Kconfig | 10 + + drivers/mmc/host/Makefile | 1 + + drivers/mmc/host/bcm2835-sdhost.c | 2196 +++++++++++++++++++++++++++++ + 3 files changed, 2207 insertions(+) + create mode 100644 drivers/mmc/host/bcm2835-sdhost.c + +--- a/drivers/mmc/host/Kconfig ++++ b/drivers/mmc/host/Kconfig +@@ -34,6 +34,16 @@ config MMC_BCM2835_PIO_DMA_BARRIER + + If unsure, say 2 here. + ++config MMC_BCM2835_SDHOST ++ tristate "Support for the SDHost controller on BCM2708/9" ++ depends on ARCH_BCM2835 ++ help ++ This selects the SDHost controller on BCM2835/6. ++ ++ If you have a controller with this interface, say Y or M here. ++ ++ If unsure, say N. ++ + config MMC_DEBUG + bool "MMC host drivers debugging" + depends on MMC != n +--- a/drivers/mmc/host/Makefile ++++ b/drivers/mmc/host/Makefile +@@ -25,6 +25,7 @@ obj-$(CONFIG_MMC_SDHCI_MILBEAUT) += sdhc + obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o + obj-$(CONFIG_MMC_SDHCI_AM654) += sdhci_am654.o + obj-$(CONFIG_MMC_BCM2835_MMC) += bcm2835-mmc.o ++obj-$(CONFIG_MMC_BCM2835_SDHOST) += bcm2835-sdhost.o + obj-$(CONFIG_MMC_WBSD) += wbsd.o + obj-$(CONFIG_MMC_AU1X) += au1xmmc.o + obj-$(CONFIG_MMC_ALCOR) += alcor.o +--- /dev/null ++++ b/drivers/mmc/host/bcm2835-sdhost.c +@@ -0,0 +1,2196 @@ ++/* ++ * BCM2835 SD host driver. ++ * ++ * Author: Phil Elwell ++ * Copyright (C) 2015-2016 Raspberry Pi (Trading) Ltd. ++ * ++ * Based on ++ * mmc-bcm2835.c by Gellert Weisz ++ * which is, in turn, based on ++ * sdhci-bcm2708.c by Broadcom ++ * sdhci-bcm2835.c by Stephen Warren and Oleksandr Tymoshenko ++ * sdhci.c and sdhci-pci.c by Pierre Ossman ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms and conditions of the GNU General Public License, ++ * version 2, as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope it will be useful, but WITHOUT ++ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or ++ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for ++ * more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program. If not, see . ++ */ ++ ++#define FIFO_READ_THRESHOLD 4 ++#define FIFO_WRITE_THRESHOLD 4 ++#define ALLOW_CMD23_READ 1 ++#define ALLOW_CMD23_WRITE 0 ++#define ENABLE_LOG 1 ++#define SDDATA_FIFO_PIO_BURST 8 ++#define CMD_DALLY_US 1 ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++/* For mmc_card_blockaddr */ ++#include "../core/card.h" ++ ++#define DRIVER_NAME "sdhost-bcm2835" ++ ++#define SDCMD 0x00 /* Command to SD card - 16 R/W */ ++#define SDARG 0x04 /* Argument to SD card - 32 R/W */ ++#define SDTOUT 0x08 /* Start value for timeout counter - 32 R/W */ ++#define SDCDIV 0x0c /* Start value for clock divider - 11 R/W */ ++#define SDRSP0 0x10 /* SD card response (31:0) - 32 R */ ++#define SDRSP1 0x14 /* SD card response (63:32) - 32 R */ ++#define SDRSP2 0x18 /* SD card response (95:64) - 32 R */ ++#define SDRSP3 0x1c /* SD card response (127:96) - 32 R */ ++#define SDHSTS 0x20 /* SD host status - 11 R */ ++#define SDVDD 0x30 /* SD card power control - 1 R/W */ ++#define SDEDM 0x34 /* Emergency Debug Mode - 13 R/W */ ++#define SDHCFG 0x38 /* Host configuration - 2 R/W */ ++#define SDHBCT 0x3c /* Host byte count (debug) - 32 R/W */ ++#define SDDATA 0x40 /* Data to/from SD card - 32 R/W */ ++#define SDHBLC 0x50 /* Host block count (SDIO/SDHC) - 9 R/W */ ++ ++#define SDCMD_NEW_FLAG 0x8000 ++#define SDCMD_FAIL_FLAG 0x4000 ++#define SDCMD_BUSYWAIT 0x800 ++#define SDCMD_NO_RESPONSE 0x400 ++#define SDCMD_LONG_RESPONSE 0x200 ++#define SDCMD_WRITE_CMD 0x80 ++#define SDCMD_READ_CMD 0x40 ++#define SDCMD_CMD_MASK 0x3f ++ ++#define SDCDIV_MAX_CDIV 0x7ff ++ ++#define SDHSTS_BUSY_IRPT 0x400 ++#define SDHSTS_BLOCK_IRPT 0x200 ++#define SDHSTS_SDIO_IRPT 0x100 ++#define SDHSTS_REW_TIME_OUT 0x80 ++#define SDHSTS_CMD_TIME_OUT 0x40 ++#define SDHSTS_CRC16_ERROR 0x20 ++#define SDHSTS_CRC7_ERROR 0x10 ++#define SDHSTS_FIFO_ERROR 0x08 ++/* Reserved */ ++/* Reserved */ ++#define SDHSTS_DATA_FLAG 0x01 ++ ++#define SDHSTS_TRANSFER_ERROR_MASK (SDHSTS_CRC7_ERROR|SDHSTS_CRC16_ERROR|SDHSTS_REW_TIME_OUT|SDHSTS_FIFO_ERROR) ++#define SDHSTS_ERROR_MASK (SDHSTS_CMD_TIME_OUT|SDHSTS_TRANSFER_ERROR_MASK) ++ ++#define SDHCFG_BUSY_IRPT_EN (1<<10) ++#define SDHCFG_BLOCK_IRPT_EN (1<<8) ++#define SDHCFG_SDIO_IRPT_EN (1<<5) ++#define SDHCFG_DATA_IRPT_EN (1<<4) ++#define SDHCFG_SLOW_CARD (1<<3) ++#define SDHCFG_WIDE_EXT_BUS (1<<2) ++#define SDHCFG_WIDE_INT_BUS (1<<1) ++#define SDHCFG_REL_CMD_LINE (1<<0) ++ ++#define SDEDM_FORCE_DATA_MODE (1<<19) ++#define SDEDM_CLOCK_PULSE (1<<20) ++#define SDEDM_BYPASS (1<<21) ++ ++#define SDEDM_WRITE_THRESHOLD_SHIFT 9 ++#define SDEDM_READ_THRESHOLD_SHIFT 14 ++#define SDEDM_THRESHOLD_MASK 0x1f ++ ++#define SDEDM_FSM_MASK 0xf ++#define SDEDM_FSM_IDENTMODE 0x0 ++#define SDEDM_FSM_DATAMODE 0x1 ++#define SDEDM_FSM_READDATA 0x2 ++#define SDEDM_FSM_WRITEDATA 0x3 ++#define SDEDM_FSM_READWAIT 0x4 ++#define SDEDM_FSM_READCRC 0x5 ++#define SDEDM_FSM_WRITECRC 0x6 ++#define SDEDM_FSM_WRITEWAIT1 0x7 ++#define SDEDM_FSM_POWERDOWN 0x8 ++#define SDEDM_FSM_POWERUP 0x9 ++#define SDEDM_FSM_WRITESTART1 0xa ++#define SDEDM_FSM_WRITESTART2 0xb ++#define SDEDM_FSM_GENPULSES 0xc ++#define SDEDM_FSM_WRITEWAIT2 0xd ++#define SDEDM_FSM_STARTPOWDOWN 0xf ++ ++#define SDDATA_FIFO_WORDS 16 ++ ++#define USE_CMD23_FLAGS ((ALLOW_CMD23_READ * MMC_DATA_READ) | \ ++ (ALLOW_CMD23_WRITE * MMC_DATA_WRITE)) ++ ++#define MHZ 1000000 ++ ++ ++struct bcm2835_host { ++ spinlock_t lock; ++ ++ void __iomem *ioaddr; ++ phys_addr_t bus_addr; ++ ++ struct mmc_host *mmc; ++ ++ u32 pio_timeout; /* In jiffies */ ++ ++ int clock; /* Current clock speed */ ++ ++ bool slow_card; /* Force 11-bit divisor */ ++ ++ unsigned int max_clk; /* Max possible freq */ ++ ++ struct tasklet_struct finish_tasklet; /* Tasklet structures */ ++ ++ struct work_struct cmd_wait_wq; /* Workqueue function */ ++ ++ struct timer_list timer; /* Timer for timeouts */ ++ ++ struct sg_mapping_iter sg_miter; /* SG state for PIO */ ++ unsigned int blocks; /* remaining PIO blocks */ ++ ++ int irq; /* Device IRQ */ ++ ++ u32 cmd_quick_poll_retries; ++ u32 ns_per_fifo_word; ++ ++ /* cached registers */ ++ u32 hcfg; ++ u32 cdiv; ++ ++ struct mmc_request *mrq; /* Current request */ ++ struct mmc_command *cmd; /* Current command */ ++ struct mmc_data *data; /* Current data request */ ++ unsigned int data_complete:1; /* Data finished before cmd */ ++ ++ unsigned int flush_fifo:1; /* Drain the fifo when finishing */ ++ ++ unsigned int use_busy:1; /* Wait for busy interrupt */ ++ ++ unsigned int use_sbc:1; /* Send CMD23 */ ++ ++ unsigned int debug:1; /* Enable debug output */ ++ unsigned int firmware_sets_cdiv:1; /* Let the firmware manage the clock */ ++ unsigned int reset_clock:1; /* Reset the clock fore the next request */ ++ ++ /*DMA part*/ ++ struct dma_chan *dma_chan_rxtx; /* DMA channel for reads and writes */ ++ struct dma_chan *dma_chan; /* Channel in use */ ++ struct dma_slave_config dma_cfg_rx; ++ struct dma_slave_config dma_cfg_tx; ++ struct dma_async_tx_descriptor *dma_desc; ++ u32 dma_dir; ++ u32 drain_words; ++ struct page *drain_page; ++ u32 drain_offset; ++ ++ bool allow_dma; ++ bool use_dma; ++ /*end of DMA part*/ ++ ++ int max_delay; /* maximum length of time spent waiting */ ++ struct timespec64 stop_time; /* when the last stop was issued */ ++ u32 delay_after_stop; /* minimum time between stop and subsequent data transfer */ ++ u32 delay_after_this_stop; /* minimum time between this stop and subsequent data transfer */ ++ u32 user_overclock_50; /* User's preferred frequency to use when 50MHz is requested (in MHz) */ ++ u32 overclock_50; /* frequency to use when 50MHz is requested (in MHz) */ ++ u32 overclock; /* Current frequency if overclocked, else zero */ ++ u32 pio_limit; /* Maximum block count for PIO (0 = always DMA) */ ++ ++ u32 sectors; /* Cached card size in sectors */ ++}; ++ ++#if ENABLE_LOG ++ ++struct log_entry_struct { ++ char event[4]; ++ u32 timestamp; ++ u32 param1; ++ u32 param2; ++}; ++ ++typedef struct log_entry_struct LOG_ENTRY_T; ++ ++LOG_ENTRY_T *sdhost_log_buf; ++dma_addr_t sdhost_log_addr; ++static u32 sdhost_log_idx; ++static spinlock_t log_lock; ++static void __iomem *timer_base; ++ ++#define LOG_ENTRIES (256*1) ++#define LOG_SIZE (sizeof(LOG_ENTRY_T)*LOG_ENTRIES) ++ ++static void log_init(struct device *dev, u32 bus_to_phys) ++{ ++ spin_lock_init(&log_lock); ++ sdhost_log_buf = dma_alloc_coherent(dev, LOG_SIZE, &sdhost_log_addr, ++ GFP_KERNEL); ++ if (sdhost_log_buf) { ++ pr_info("sdhost: log_buf @ %p (%llx)\n", ++ sdhost_log_buf, (u64)sdhost_log_addr); ++ timer_base = ioremap(bus_to_phys + 0x7e003000, SZ_4K); ++ if (!timer_base) ++ pr_err("sdhost: failed to remap timer\n"); ++ } ++ else ++ pr_err("sdhost: failed to allocate log buf\n"); ++} ++ ++static void log_event_impl(const char *event, u32 param1, u32 param2) ++{ ++ if (sdhost_log_buf) { ++ LOG_ENTRY_T *entry; ++ unsigned long flags; ++ ++ spin_lock_irqsave(&log_lock, flags); ++ ++ entry = sdhost_log_buf + sdhost_log_idx; ++ memcpy(entry->event, event, 4); ++ entry->timestamp = (readl(timer_base + 4) & 0x3fffffff) + ++ (smp_processor_id()<<30); ++ entry->param1 = param1; ++ entry->param2 = param2; ++ sdhost_log_idx = (sdhost_log_idx + 1) % LOG_ENTRIES; ++ ++ spin_unlock_irqrestore(&log_lock, flags); ++ } ++} ++ ++static void log_dump(void) ++{ ++ if (sdhost_log_buf) { ++ LOG_ENTRY_T *entry; ++ unsigned long flags; ++ int idx; ++ ++ spin_lock_irqsave(&log_lock, flags); ++ ++ idx = sdhost_log_idx; ++ do { ++ entry = sdhost_log_buf + idx; ++ if (entry->event[0] != '\0') ++ pr_info("[%08x] %.4s %x %x\n", ++ entry->timestamp, ++ entry->event, ++ entry->param1, ++ entry->param2); ++ idx = (idx + 1) % LOG_ENTRIES; ++ } while (idx != sdhost_log_idx); ++ ++ spin_unlock_irqrestore(&log_lock, flags); ++ } ++} ++ ++#define log_event(event, param1, param2) log_event_impl(event, (u32)(uintptr_t)param1, (u32)(uintptr_t)param2) ++ ++#else ++ ++#define log_init(x) (void)0 ++#define log_event(event, param1, param2) (void)0 ++#define log_dump() (void)0 ++ ++#endif ++ ++static inline void bcm2835_sdhost_write(struct bcm2835_host *host, u32 val, int reg) ++{ ++ writel(val, host->ioaddr + reg); ++} ++ ++static inline u32 bcm2835_sdhost_read(struct bcm2835_host *host, int reg) ++{ ++ return readl(host->ioaddr + reg); ++} ++ ++static inline u32 bcm2835_sdhost_read_relaxed(struct bcm2835_host *host, int reg) ++{ ++ return readl_relaxed(host->ioaddr + reg); ++} ++ ++static void bcm2835_sdhost_dumpcmd(struct bcm2835_host *host, ++ struct mmc_command *cmd, ++ const char *label) ++{ ++ if (cmd) ++ pr_info("%s:%c%s op %d arg 0x%x flags 0x%x - resp %08x %08x %08x %08x, err %d\n", ++ mmc_hostname(host->mmc), ++ (cmd == host->cmd) ? '>' : ' ', ++ label, cmd->opcode, cmd->arg, cmd->flags, ++ cmd->resp[0], cmd->resp[1], cmd->resp[2], cmd->resp[3], ++ cmd->error); ++} ++ ++static void bcm2835_sdhost_dumpregs(struct bcm2835_host *host) ++{ ++ if (host->mrq) ++ { ++ bcm2835_sdhost_dumpcmd(host, host->mrq->sbc, "sbc"); ++ bcm2835_sdhost_dumpcmd(host, host->mrq->cmd, "cmd"); ++ if (host->mrq->data) ++ pr_info("%s: data blocks %x blksz %x - err %d\n", ++ mmc_hostname(host->mmc), ++ host->mrq->data->blocks, ++ host->mrq->data->blksz, ++ host->mrq->data->error); ++ bcm2835_sdhost_dumpcmd(host, host->mrq->stop, "stop"); ++ } ++ ++ pr_info("%s: =========== REGISTER DUMP ===========\n", ++ mmc_hostname(host->mmc)); ++ ++ pr_info("%s: SDCMD 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDCMD)); ++ pr_info("%s: SDARG 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDARG)); ++ pr_info("%s: SDTOUT 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDTOUT)); ++ pr_info("%s: SDCDIV 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDCDIV)); ++ pr_info("%s: SDRSP0 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDRSP0)); ++ pr_info("%s: SDRSP1 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDRSP1)); ++ pr_info("%s: SDRSP2 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDRSP2)); ++ pr_info("%s: SDRSP3 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDRSP3)); ++ pr_info("%s: SDHSTS 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDHSTS)); ++ pr_info("%s: SDVDD 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDVDD)); ++ pr_info("%s: SDEDM 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDEDM)); ++ pr_info("%s: SDHCFG 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDHCFG)); ++ pr_info("%s: SDHBCT 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDHBCT)); ++ pr_info("%s: SDHBLC 0x%08x\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDHBLC)); ++ ++ pr_info("%s: ===========================================\n", ++ mmc_hostname(host->mmc)); ++} ++ ++static void bcm2835_sdhost_set_power(struct bcm2835_host *host, bool on) ++{ ++ bcm2835_sdhost_write(host, on ? 1 : 0, SDVDD); ++} ++ ++static void bcm2835_sdhost_reset_internal(struct bcm2835_host *host) ++{ ++ u32 temp; ++ ++ if (host->debug) ++ pr_info("%s: reset\n", mmc_hostname(host->mmc)); ++ ++ bcm2835_sdhost_set_power(host, false); ++ ++ bcm2835_sdhost_write(host, 0, SDCMD); ++ bcm2835_sdhost_write(host, 0, SDARG); ++ bcm2835_sdhost_write(host, 0xf00000, SDTOUT); ++ bcm2835_sdhost_write(host, 0, SDCDIV); ++ bcm2835_sdhost_write(host, 0x7f8, SDHSTS); /* Write 1s to clear */ ++ bcm2835_sdhost_write(host, 0, SDHCFG); ++ bcm2835_sdhost_write(host, 0, SDHBCT); ++ bcm2835_sdhost_write(host, 0, SDHBLC); ++ ++ /* Limit fifo usage due to silicon bug */ ++ temp = bcm2835_sdhost_read(host, SDEDM); ++ temp &= ~((SDEDM_THRESHOLD_MASK<clock = 0; ++ host->sectors = 0; ++ bcm2835_sdhost_write(host, host->hcfg, SDHCFG); ++ bcm2835_sdhost_write(host, SDCDIV_MAX_CDIV, SDCDIV); ++} ++ ++static void bcm2835_sdhost_reset(struct mmc_host *mmc) ++{ ++ struct bcm2835_host *host = mmc_priv(mmc); ++ unsigned long flags; ++ spin_lock_irqsave(&host->lock, flags); ++ log_event("RST<", 0, 0); ++ ++ bcm2835_sdhost_reset_internal(host); ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static void bcm2835_sdhost_set_ios(struct mmc_host *mmc, struct mmc_ios *ios); ++ ++static void bcm2835_sdhost_init(struct bcm2835_host *host, int soft) ++{ ++ pr_debug("bcm2835_sdhost_init(%d)\n", soft); ++ ++ /* Set interrupt enables */ ++ host->hcfg = SDHCFG_BUSY_IRPT_EN; ++ ++ bcm2835_sdhost_reset_internal(host); ++ ++ if (soft) { ++ /* force clock reconfiguration */ ++ host->clock = 0; ++ bcm2835_sdhost_set_ios(host->mmc, &host->mmc->ios); ++ } ++} ++ ++static void bcm2835_sdhost_wait_transfer_complete(struct bcm2835_host *host) ++{ ++ int timediff; ++ u32 alternate_idle; ++ u32 edm; ++ ++ alternate_idle = (host->mrq->data->flags & MMC_DATA_READ) ? ++ SDEDM_FSM_READWAIT : SDEDM_FSM_WRITESTART1; ++ ++ edm = bcm2835_sdhost_read(host, SDEDM); ++ ++ log_event("WTC<", edm, 0); ++ ++ timediff = 0; ++ ++ while (1) { ++ u32 fsm = edm & SDEDM_FSM_MASK; ++ if ((fsm == SDEDM_FSM_IDENTMODE) || ++ (fsm == SDEDM_FSM_DATAMODE)) ++ break; ++ if (fsm == alternate_idle) { ++ bcm2835_sdhost_write(host, ++ edm | SDEDM_FORCE_DATA_MODE, ++ SDEDM); ++ break; ++ } ++ ++ timediff++; ++ if (timediff == 100000) { ++ pr_err("%s: wait_transfer_complete - still waiting after %d retries\n", ++ mmc_hostname(host->mmc), ++ timediff); ++ log_dump(); ++ bcm2835_sdhost_dumpregs(host); ++ host->mrq->data->error = -ETIMEDOUT; ++ log_event("WTC!", edm, 0); ++ return; ++ } ++ cpu_relax(); ++ edm = bcm2835_sdhost_read(host, SDEDM); ++ } ++ log_event("WTC>", edm, 0); ++} ++ ++static void bcm2835_sdhost_finish_data(struct bcm2835_host *host); ++ ++static void bcm2835_sdhost_dma_complete(void *param) ++{ ++ struct bcm2835_host *host = param; ++ struct mmc_data *data = host->data; ++ unsigned long flags; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ log_event("DMA<", host->data, bcm2835_sdhost_read(host, SDHSTS)); ++ log_event("DMA ", bcm2835_sdhost_read(host, SDCMD), ++ bcm2835_sdhost_read(host, SDEDM)); ++ ++ if (host->dma_chan) { ++ dma_unmap_sg(host->dma_chan->device->dev, ++ data->sg, data->sg_len, ++ host->dma_dir); ++ ++ host->dma_chan = NULL; ++ } ++ ++ if (host->drain_words) { ++ void *page; ++ u32 *buf; ++ ++ if (host->drain_offset & PAGE_MASK) { ++ host->drain_page += host->drain_offset >> PAGE_SHIFT; ++ host->drain_offset &= ~PAGE_MASK; ++ } ++ ++ page = kmap_atomic(host->drain_page); ++ buf = page + host->drain_offset; ++ ++ while (host->drain_words) { ++ u32 edm = bcm2835_sdhost_read(host, SDEDM); ++ if ((edm >> 4) & 0x1f) ++ *(buf++) = bcm2835_sdhost_read(host, ++ SDDATA); ++ host->drain_words--; ++ } ++ ++ kunmap_atomic(page); ++ } ++ ++ bcm2835_sdhost_finish_data(host); ++ ++ log_event("DMA>", host->data, 0); ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static void bcm2835_sdhost_read_block_pio(struct bcm2835_host *host) ++{ ++ unsigned long flags; ++ size_t blksize, len; ++ u32 *buf; ++ unsigned long wait_max; ++ ++ blksize = host->data->blksz; ++ ++ wait_max = jiffies + msecs_to_jiffies(host->pio_timeout); ++ ++ local_irq_save(flags); ++ ++ while (blksize) { ++ int copy_words; ++ u32 hsts = 0; ++ ++ if (!sg_miter_next(&host->sg_miter)) { ++ host->data->error = -EINVAL; ++ break; ++ } ++ ++ len = min(host->sg_miter.length, blksize); ++ if (len % 4) { ++ host->data->error = -EINVAL; ++ break; ++ } ++ ++ blksize -= len; ++ host->sg_miter.consumed = len; ++ ++ buf = (u32 *)host->sg_miter.addr; ++ ++ copy_words = len/4; ++ ++ while (copy_words) { ++ int burst_words, words; ++ u32 edm; ++ ++ burst_words = SDDATA_FIFO_PIO_BURST; ++ if (burst_words > copy_words) ++ burst_words = copy_words; ++ edm = bcm2835_sdhost_read(host, SDEDM); ++ words = ((edm >> 4) & 0x1f); ++ ++ if (words < burst_words) { ++ int fsm_state = (edm & SDEDM_FSM_MASK); ++ if ((fsm_state != SDEDM_FSM_READDATA) && ++ (fsm_state != SDEDM_FSM_READWAIT) && ++ (fsm_state != SDEDM_FSM_READCRC)) { ++ hsts = bcm2835_sdhost_read(host, ++ SDHSTS); ++ pr_info("%s: fsm %x, hsts %x\n", ++ mmc_hostname(host->mmc), ++ fsm_state, hsts); ++ if (hsts & SDHSTS_ERROR_MASK) ++ break; ++ } ++ ++ if (time_after(jiffies, wait_max)) { ++ pr_err("%s: PIO read timeout - EDM %x\n", ++ mmc_hostname(host->mmc), ++ edm); ++ hsts = SDHSTS_REW_TIME_OUT; ++ break; ++ } ++ ndelay((burst_words - words) * ++ host->ns_per_fifo_word); ++ continue; ++ } else if (words > copy_words) { ++ words = copy_words; ++ } ++ ++ copy_words -= words; ++ ++ while (words) { ++ *(buf++) = bcm2835_sdhost_read(host, SDDATA); ++ words--; ++ } ++ } ++ ++ if (hsts & SDHSTS_ERROR_MASK) ++ break; ++ } ++ ++ sg_miter_stop(&host->sg_miter); ++ ++ local_irq_restore(flags); ++} ++ ++static void bcm2835_sdhost_write_block_pio(struct bcm2835_host *host) ++{ ++ unsigned long flags; ++ size_t blksize, len; ++ u32 *buf; ++ unsigned long wait_max; ++ ++ blksize = host->data->blksz; ++ ++ wait_max = jiffies + msecs_to_jiffies(host->pio_timeout); ++ ++ local_irq_save(flags); ++ ++ while (blksize) { ++ int copy_words; ++ u32 hsts = 0; ++ ++ if (!sg_miter_next(&host->sg_miter)) { ++ host->data->error = -EINVAL; ++ break; ++ } ++ ++ len = min(host->sg_miter.length, blksize); ++ if (len % 4) { ++ host->data->error = -EINVAL; ++ break; ++ } ++ ++ blksize -= len; ++ host->sg_miter.consumed = len; ++ ++ buf = (u32 *)host->sg_miter.addr; ++ ++ copy_words = len/4; ++ ++ while (copy_words) { ++ int burst_words, words; ++ u32 edm; ++ ++ burst_words = SDDATA_FIFO_PIO_BURST; ++ if (burst_words > copy_words) ++ burst_words = copy_words; ++ edm = bcm2835_sdhost_read(host, SDEDM); ++ words = SDDATA_FIFO_WORDS - ((edm >> 4) & 0x1f); ++ ++ if (words < burst_words) { ++ int fsm_state = (edm & SDEDM_FSM_MASK); ++ if ((fsm_state != SDEDM_FSM_WRITEDATA) && ++ (fsm_state != SDEDM_FSM_WRITESTART1) && ++ (fsm_state != SDEDM_FSM_WRITESTART2)) { ++ hsts = bcm2835_sdhost_read(host, ++ SDHSTS); ++ pr_info("%s: fsm %x, hsts %x\n", ++ mmc_hostname(host->mmc), ++ fsm_state, hsts); ++ if (hsts & SDHSTS_ERROR_MASK) ++ break; ++ } ++ ++ if (time_after(jiffies, wait_max)) { ++ pr_err("%s: PIO write timeout - EDM %x\n", ++ mmc_hostname(host->mmc), ++ edm); ++ hsts = SDHSTS_REW_TIME_OUT; ++ break; ++ } ++ ndelay((burst_words - words) * ++ host->ns_per_fifo_word); ++ continue; ++ } else if (words > copy_words) { ++ words = copy_words; ++ } ++ ++ copy_words -= words; ++ ++ while (words) { ++ bcm2835_sdhost_write(host, *(buf++), SDDATA); ++ words--; ++ } ++ } ++ ++ if (hsts & SDHSTS_ERROR_MASK) ++ break; ++ } ++ ++ sg_miter_stop(&host->sg_miter); ++ ++ local_irq_restore(flags); ++} ++ ++static void bcm2835_sdhost_transfer_pio(struct bcm2835_host *host) ++{ ++ u32 sdhsts; ++ bool is_read; ++ BUG_ON(!host->data); ++ log_event("XFP<", host->data, host->blocks); ++ ++ is_read = (host->data->flags & MMC_DATA_READ) != 0; ++ if (is_read) ++ bcm2835_sdhost_read_block_pio(host); ++ else ++ bcm2835_sdhost_write_block_pio(host); ++ ++ sdhsts = bcm2835_sdhost_read(host, SDHSTS); ++ if (sdhsts & (SDHSTS_CRC16_ERROR | ++ SDHSTS_CRC7_ERROR | ++ SDHSTS_FIFO_ERROR)) { ++ pr_err("%s: %s transfer error - HSTS %x\n", ++ mmc_hostname(host->mmc), ++ is_read ? "read" : "write", ++ sdhsts); ++ host->data->error = -EILSEQ; ++ } else if ((sdhsts & (SDHSTS_CMD_TIME_OUT | ++ SDHSTS_REW_TIME_OUT))) { ++ pr_err("%s: %s timeout error - HSTS %x\n", ++ mmc_hostname(host->mmc), ++ is_read ? "read" : "write", ++ sdhsts); ++ host->data->error = -ETIMEDOUT; ++ } ++ log_event("XFP>", host->data, host->blocks); ++} ++ ++static void bcm2835_sdhost_prepare_dma(struct bcm2835_host *host, ++ struct mmc_data *data) ++{ ++ int len, dir_data, dir_slave; ++ struct dma_async_tx_descriptor *desc = NULL; ++ struct dma_chan *dma_chan; ++ ++ log_event("PRD<", data, 0); ++ pr_debug("bcm2835_sdhost_prepare_dma()\n"); ++ ++ dma_chan = host->dma_chan_rxtx; ++ if (data->flags & MMC_DATA_READ) { ++ dir_data = DMA_FROM_DEVICE; ++ dir_slave = DMA_DEV_TO_MEM; ++ } else { ++ dir_data = DMA_TO_DEVICE; ++ dir_slave = DMA_MEM_TO_DEV; ++ } ++ log_event("PRD1", dma_chan, 0); ++ ++ BUG_ON(!dma_chan->device); ++ BUG_ON(!dma_chan->device->dev); ++ BUG_ON(!data->sg); ++ ++ /* The block doesn't manage the FIFO DREQs properly for multi-block ++ transfers, so don't attempt to DMA the final few words. ++ Unfortunately this requires the final sg entry to be trimmed. ++ N.B. This code demands that the overspill is contained in ++ a single sg entry. ++ */ ++ ++ host->drain_words = 0; ++ if ((data->blocks > 1) && (dir_data == DMA_FROM_DEVICE)) { ++ struct scatterlist *sg; ++ u32 len; ++ int i; ++ ++ len = min((u32)(FIFO_READ_THRESHOLD - 1) * 4, ++ (u32)data->blocks * data->blksz); ++ ++ for_each_sg(data->sg, sg, data->sg_len, i) { ++ if (sg_is_last(sg)) { ++ BUG_ON(sg->length < len); ++ sg->length -= len; ++ host->drain_page = sg_page(sg); ++ host->drain_offset = sg->offset + sg->length; ++ } ++ } ++ host->drain_words = len/4; ++ } ++ ++ /* The parameters have already been validated, so this will not fail */ ++ (void)dmaengine_slave_config(dma_chan, ++ (dir_data == DMA_FROM_DEVICE) ? ++ &host->dma_cfg_rx : ++ &host->dma_cfg_tx); ++ ++ len = dma_map_sg(dma_chan->device->dev, data->sg, data->sg_len, ++ dir_data); ++ ++ log_event("PRD2", len, 0); ++ if (len > 0) ++ desc = dmaengine_prep_slave_sg(dma_chan, data->sg, ++ len, dir_slave, ++ DMA_PREP_INTERRUPT | DMA_CTRL_ACK); ++ log_event("PRD3", desc, 0); ++ ++ if (desc) { ++ desc->callback = bcm2835_sdhost_dma_complete; ++ desc->callback_param = host; ++ host->dma_desc = desc; ++ host->dma_chan = dma_chan; ++ host->dma_dir = dir_data; ++ } ++ log_event("PDM>", data, 0); ++} ++ ++static void bcm2835_sdhost_start_dma(struct bcm2835_host *host) ++{ ++ log_event("SDMA", host->data, host->dma_chan); ++ dmaengine_submit(host->dma_desc); ++ dma_async_issue_pending(host->dma_chan); ++} ++ ++static void bcm2835_sdhost_set_transfer_irqs(struct bcm2835_host *host) ++{ ++ u32 all_irqs = SDHCFG_DATA_IRPT_EN | SDHCFG_BLOCK_IRPT_EN | ++ SDHCFG_BUSY_IRPT_EN; ++ if (host->dma_desc) ++ host->hcfg = (host->hcfg & ~all_irqs) | ++ SDHCFG_BUSY_IRPT_EN; ++ else ++ host->hcfg = (host->hcfg & ~all_irqs) | ++ SDHCFG_DATA_IRPT_EN | ++ SDHCFG_BUSY_IRPT_EN; ++ ++ bcm2835_sdhost_write(host, host->hcfg, SDHCFG); ++} ++ ++static void bcm2835_sdhost_prepare_data(struct bcm2835_host *host, struct mmc_command *cmd) ++{ ++ struct mmc_data *data = cmd->data; ++ ++ WARN_ON(host->data); ++ ++ host->data = data; ++ if (!data) ++ return; ++ ++ /* Sanity checks */ ++ BUG_ON(data->blksz * data->blocks > 524288); ++ BUG_ON(data->blksz > host->mmc->max_blk_size); ++ BUG_ON(data->blocks > 65535); ++ ++ host->data_complete = 0; ++ host->flush_fifo = 0; ++ host->data->bytes_xfered = 0; ++ ++ if (!host->sectors && host->mmc->card) { ++ struct mmc_card *card = host->mmc->card; ++ if (!mmc_card_sd(card) && mmc_card_blockaddr(card)) { ++ /* ++ * The EXT_CSD sector count is in number of 512 byte ++ * sectors. ++ */ ++ host->sectors = card->ext_csd.sectors; ++ } else { ++ /* ++ * The CSD capacity field is in units of read_blkbits. ++ * set_capacity takes units of 512 bytes. ++ */ ++ host->sectors = card->csd.capacity << ++ (card->csd.read_blkbits - 9); ++ } ++ } ++ ++ if (!host->dma_desc) { ++ /* Use PIO */ ++ int flags = SG_MITER_ATOMIC; ++ ++ if (data->flags & MMC_DATA_READ) ++ flags |= SG_MITER_TO_SG; ++ else ++ flags |= SG_MITER_FROM_SG; ++ sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags); ++ host->blocks = data->blocks; ++ } ++ ++ bcm2835_sdhost_set_transfer_irqs(host); ++ ++ bcm2835_sdhost_write(host, data->blksz, SDHBCT); ++ bcm2835_sdhost_write(host, data->blocks, SDHBLC); ++ ++ BUG_ON(!host->data); ++} ++ ++bool bcm2835_sdhost_send_command(struct bcm2835_host *host, ++ struct mmc_command *cmd) ++{ ++ u32 sdcmd, sdhsts; ++ unsigned long timeout; ++ int delay; ++ ++ WARN_ON(host->cmd); ++ log_event("CMD<", cmd->opcode, cmd->arg); ++ ++ if (cmd->data) ++ pr_debug("%s: send_command %d 0x%x " ++ "(flags 0x%x) - %s %d*%d\n", ++ mmc_hostname(host->mmc), ++ cmd->opcode, cmd->arg, cmd->flags, ++ (cmd->data->flags & MMC_DATA_READ) ? ++ "read" : "write", cmd->data->blocks, ++ cmd->data->blksz); ++ else ++ pr_debug("%s: send_command %d 0x%x (flags 0x%x)\n", ++ mmc_hostname(host->mmc), ++ cmd->opcode, cmd->arg, cmd->flags); ++ ++ /* Wait max 100 ms */ ++ timeout = 10000; ++ ++ while (bcm2835_sdhost_read(host, SDCMD) & SDCMD_NEW_FLAG) { ++ if (timeout == 0) { ++ pr_warn("%s: previous command never completed.\n", ++ mmc_hostname(host->mmc)); ++ if (host->debug) ++ bcm2835_sdhost_dumpregs(host); ++ cmd->error = -EILSEQ; ++ tasklet_schedule(&host->finish_tasklet); ++ return false; ++ } ++ timeout--; ++ udelay(10); ++ } ++ ++ delay = (10000 - timeout)/100; ++ if (delay > host->max_delay) { ++ host->max_delay = delay; ++ pr_warn("%s: controller hung for %d ms\n", ++ mmc_hostname(host->mmc), ++ host->max_delay); ++ } ++ ++ timeout = jiffies; ++ if (!cmd->data && cmd->busy_timeout > 9000) ++ timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ; ++ else ++ timeout += 10 * HZ; ++ mod_timer(&host->timer, timeout); ++ ++ host->cmd = cmd; ++ ++ /* Clear any error flags */ ++ sdhsts = bcm2835_sdhost_read(host, SDHSTS); ++ if (sdhsts & SDHSTS_ERROR_MASK) ++ bcm2835_sdhost_write(host, sdhsts, SDHSTS); ++ ++ if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) { ++ pr_err("%s: unsupported response type!\n", ++ mmc_hostname(host->mmc)); ++ cmd->error = -EINVAL; ++ tasklet_schedule(&host->finish_tasklet); ++ return false; ++ } ++ ++ bcm2835_sdhost_prepare_data(host, cmd); ++ ++ bcm2835_sdhost_write(host, cmd->arg, SDARG); ++ ++ sdcmd = cmd->opcode & SDCMD_CMD_MASK; ++ ++ host->use_busy = 0; ++ if (!(cmd->flags & MMC_RSP_PRESENT)) { ++ sdcmd |= SDCMD_NO_RESPONSE; ++ } else { ++ if (cmd->flags & MMC_RSP_136) ++ sdcmd |= SDCMD_LONG_RESPONSE; ++ if (cmd->flags & MMC_RSP_BUSY) { ++ sdcmd |= SDCMD_BUSYWAIT; ++ host->use_busy = 1; ++ } ++ } ++ ++ if (cmd->data) { ++ log_event("CMDD", cmd->data->blocks, cmd->data->blksz); ++ if (host->delay_after_this_stop) { ++ struct timespec64 now; ++ int time_since_stop; ++ ++ ktime_get_real_ts64(&now); ++ time_since_stop = now.tv_sec - host->stop_time.tv_sec; ++ if (time_since_stop < 2) { ++ /* Possibly less than one second */ ++ time_since_stop = time_since_stop * 1000000 + ++ (now.tv_nsec - host->stop_time.tv_nsec)/1000; ++ if (time_since_stop < ++ host->delay_after_this_stop) ++ udelay(host->delay_after_this_stop - ++ time_since_stop); ++ } ++ } ++ ++ host->delay_after_this_stop = host->delay_after_stop; ++ if ((cmd->data->flags & MMC_DATA_READ) && !host->use_sbc) { ++ /* See if read crosses one of the hazardous sectors */ ++ u32 first_blk, last_blk; ++ ++ /* Intentionally include the following sector because ++ without CMD23/SBC the read may run on. */ ++ first_blk = host->mrq->cmd->arg; ++ last_blk = first_blk + cmd->data->blocks; ++ ++ if (((last_blk >= (host->sectors - 64)) && ++ (first_blk <= (host->sectors - 64))) || ++ ((last_blk >= (host->sectors - 32)) && ++ (first_blk <= (host->sectors - 32)))) { ++ host->delay_after_this_stop = ++ max(250u, host->delay_after_stop); ++ } ++ } ++ ++ if (cmd->data->flags & MMC_DATA_WRITE) ++ sdcmd |= SDCMD_WRITE_CMD; ++ if (cmd->data->flags & MMC_DATA_READ) ++ sdcmd |= SDCMD_READ_CMD; ++ } ++ ++ bcm2835_sdhost_write(host, sdcmd | SDCMD_NEW_FLAG, SDCMD); ++ ++ return true; ++} ++ ++static void bcm2835_sdhost_finish_command(struct bcm2835_host *host, ++ unsigned long *irq_flags); ++static void bcm2835_sdhost_transfer_complete(struct bcm2835_host *host); ++ ++static void bcm2835_sdhost_finish_data(struct bcm2835_host *host) ++{ ++ struct mmc_data *data; ++ ++ data = host->data; ++ BUG_ON(!data); ++ ++ log_event("FDA<", host->mrq, host->cmd); ++ pr_debug("finish_data(error %d, stop %d, sbc %d)\n", ++ data->error, data->stop ? 1 : 0, ++ host->mrq->sbc ? 1 : 0); ++ ++ host->hcfg &= ~(SDHCFG_DATA_IRPT_EN | SDHCFG_BLOCK_IRPT_EN); ++ bcm2835_sdhost_write(host, host->hcfg, SDHCFG); ++ ++ data->bytes_xfered = data->error ? 0 : (data->blksz * data->blocks); ++ ++ host->data_complete = 1; ++ ++ if (host->cmd) { ++ /* ++ * Data managed to finish before the ++ * command completed. Make sure we do ++ * things in the proper order. ++ */ ++ pr_debug("Finished early - HSTS %x\n", ++ bcm2835_sdhost_read(host, SDHSTS)); ++ } ++ else ++ bcm2835_sdhost_transfer_complete(host); ++ log_event("FDA>", host->mrq, host->cmd); ++} ++ ++static void bcm2835_sdhost_transfer_complete(struct bcm2835_host *host) ++{ ++ struct mmc_data *data; ++ ++ BUG_ON(host->cmd); ++ BUG_ON(!host->data); ++ BUG_ON(!host->data_complete); ++ ++ data = host->data; ++ host->data = NULL; ++ ++ log_event("TCM<", data, data->error); ++ pr_debug("transfer_complete(error %d, stop %d)\n", ++ data->error, data->stop ? 1 : 0); ++ ++ /* ++ * Need to send CMD12 if - ++ * a) open-ended multiblock transfer (no CMD23) ++ * b) error in multiblock transfer ++ */ ++ if (host->mrq->stop && (data->error || !host->use_sbc)) { ++ if (bcm2835_sdhost_send_command(host, host->mrq->stop)) { ++ /* No busy, so poll for completion */ ++ if (!host->use_busy) ++ bcm2835_sdhost_finish_command(host, NULL); ++ ++ if (host->delay_after_this_stop) ++ ktime_get_real_ts64(&host->stop_time); ++ } ++ } else { ++ bcm2835_sdhost_wait_transfer_complete(host); ++ tasklet_schedule(&host->finish_tasklet); ++ } ++ log_event("TCM>", data, 0); ++} ++ ++/* If irq_flags is valid, the caller is in a thread context and is allowed ++ to sleep */ ++static void bcm2835_sdhost_finish_command(struct bcm2835_host *host, ++ unsigned long *irq_flags) ++{ ++ u32 sdcmd; ++ u32 retries; ++#ifdef DEBUG ++ struct timespec64 before, after; ++ int timediff = 0; ++#endif ++ ++ log_event("FCM<", host->mrq, host->cmd); ++ pr_debug("finish_command(%x)\n", bcm2835_sdhost_read(host, SDCMD)); ++ ++ BUG_ON(!host->cmd || !host->mrq); ++ ++ /* Poll quickly at first */ ++ ++ retries = host->cmd_quick_poll_retries; ++ if (!retries) { ++ /* Work out how many polls take 1us by timing 10us */ ++ struct timespec64 start, now; ++ int us_diff; ++ ++ retries = 1; ++ do { ++ int i; ++ ++ retries *= 2; ++ ++ ktime_get_real_ts64(&start); ++ ++ for (i = 0; i < retries; i++) { ++ cpu_relax(); ++ sdcmd = bcm2835_sdhost_read(host, SDCMD); ++ } ++ ++ ktime_get_real_ts64(&now); ++ us_diff = (now.tv_sec - start.tv_sec) * 1000000 + ++ (now.tv_nsec - start.tv_nsec)/1000; ++ } while (us_diff < 10); ++ ++ host->cmd_quick_poll_retries = ((retries * us_diff + 9)*CMD_DALLY_US)/10 + 1; ++ retries = 1; // We've already waited long enough this time ++ } ++ ++ for (sdcmd = bcm2835_sdhost_read(host, SDCMD); ++ (sdcmd & SDCMD_NEW_FLAG) && retries; ++ retries--) { ++ cpu_relax(); ++ sdcmd = bcm2835_sdhost_read(host, SDCMD); ++ } ++ ++ if (!retries) { ++ unsigned long wait_max; ++ ++ if (!irq_flags) { ++ /* Schedule the work */ ++ log_event("CWWQ", 0, 0); ++ schedule_work(&host->cmd_wait_wq); ++ return; ++ } ++ ++ /* Wait max 100 ms */ ++ wait_max = jiffies + msecs_to_jiffies(100); ++ while (time_before(jiffies, wait_max)) { ++ spin_unlock_irqrestore(&host->lock, *irq_flags); ++ usleep_range(1, 10); ++ spin_lock_irqsave(&host->lock, *irq_flags); ++ sdcmd = bcm2835_sdhost_read(host, SDCMD); ++ if (!(sdcmd & SDCMD_NEW_FLAG)) ++ break; ++ } ++ } ++ ++ /* Check for errors */ ++ if (sdcmd & SDCMD_NEW_FLAG) { ++ if (host->debug) { ++ pr_err("%s: command %d never completed.\n", ++ mmc_hostname(host->mmc), host->cmd->opcode); ++ bcm2835_sdhost_dumpregs(host); ++ } ++ host->cmd->error = -EILSEQ; ++ tasklet_schedule(&host->finish_tasklet); ++ return; ++ } else if (sdcmd & SDCMD_FAIL_FLAG) { ++ u32 sdhsts = bcm2835_sdhost_read(host, SDHSTS); ++ ++ /* Clear the errors */ ++ bcm2835_sdhost_write(host, SDHSTS_ERROR_MASK, SDHSTS); ++ ++ if (host->debug) ++ pr_info("%s: error detected - CMD %x, HSTS %03x, EDM %x\n", ++ mmc_hostname(host->mmc), sdcmd, sdhsts, ++ bcm2835_sdhost_read(host, SDEDM)); ++ ++ if ((sdhsts & SDHSTS_CRC7_ERROR) && ++ (host->cmd->opcode == 1)) { ++ if (host->debug) ++ pr_info("%s: ignoring CRC7 error for CMD1\n", ++ mmc_hostname(host->mmc)); ++ } else { ++ u32 edm, fsm; ++ ++ if (sdhsts & SDHSTS_CMD_TIME_OUT) { ++ if (host->debug) ++ pr_warn("%s: command %d timeout\n", ++ mmc_hostname(host->mmc), ++ host->cmd->opcode); ++ host->cmd->error = -ETIMEDOUT; ++ } else { ++ pr_warn("%s: unexpected command %d error\n", ++ mmc_hostname(host->mmc), ++ host->cmd->opcode); ++ host->cmd->error = -EILSEQ; ++ } ++ ++ edm = readl(host->ioaddr + SDEDM); ++ fsm = edm & SDEDM_FSM_MASK; ++ if (fsm == SDEDM_FSM_READWAIT || ++ fsm == SDEDM_FSM_WRITESTART1) ++ writel(edm | SDEDM_FORCE_DATA_MODE, ++ host->ioaddr + SDEDM); ++ tasklet_schedule(&host->finish_tasklet); ++ return; ++ } ++ } ++ ++ if (host->cmd->flags & MMC_RSP_PRESENT) { ++ if (host->cmd->flags & MMC_RSP_136) { ++ int i; ++ for (i = 0; i < 4; i++) ++ host->cmd->resp[3 - i] = bcm2835_sdhost_read(host, SDRSP0 + i*4); ++ pr_debug("%s: finish_command %08x %08x %08x %08x\n", ++ mmc_hostname(host->mmc), ++ host->cmd->resp[0], host->cmd->resp[1], host->cmd->resp[2], host->cmd->resp[3]); ++ log_event("RSP ", host->cmd->resp[0], host->cmd->resp[1]); ++ } else { ++ host->cmd->resp[0] = bcm2835_sdhost_read(host, SDRSP0); ++ pr_debug("%s: finish_command %08x\n", ++ mmc_hostname(host->mmc), ++ host->cmd->resp[0]); ++ log_event("RSP ", host->cmd->resp[0], 0); ++ } ++ } ++ ++ if (host->cmd == host->mrq->sbc) { ++ /* Finished CMD23, now send actual command. */ ++ host->cmd = NULL; ++ if (bcm2835_sdhost_send_command(host, host->mrq->cmd)) { ++ if (host->data && host->dma_desc) ++ /* DMA transfer starts now, PIO starts after irq */ ++ bcm2835_sdhost_start_dma(host); ++ ++ if (!host->use_busy) ++ bcm2835_sdhost_finish_command(host, NULL); ++ } ++ } else if (host->cmd == host->mrq->stop) { ++ /* Finished CMD12 */ ++ tasklet_schedule(&host->finish_tasklet); ++ } else { ++ /* Processed actual command. */ ++ host->cmd = NULL; ++ if (!host->data) ++ tasklet_schedule(&host->finish_tasklet); ++ else if (host->data_complete) ++ bcm2835_sdhost_transfer_complete(host); ++ } ++ log_event("FCM>", host->mrq, host->cmd); ++} ++ ++static void bcm2835_sdhost_timeout(struct timer_list *t) ++{ ++ struct bcm2835_host *host = from_timer(host, t, timer); ++ unsigned long flags; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ log_event("TIM<", 0, 0); ++ ++ if (host->mrq) { ++ pr_err("%s: timeout waiting for hardware interrupt.\n", ++ mmc_hostname(host->mmc)); ++ log_dump(); ++ bcm2835_sdhost_dumpregs(host); ++ ++ if (host->data) { ++ host->data->error = -ETIMEDOUT; ++ bcm2835_sdhost_finish_data(host); ++ } else { ++ if (host->cmd) ++ host->cmd->error = -ETIMEDOUT; ++ else ++ host->mrq->cmd->error = -ETIMEDOUT; ++ ++ pr_debug("timeout_timer tasklet_schedule\n"); ++ tasklet_schedule(&host->finish_tasklet); ++ } ++ } ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static void bcm2835_sdhost_busy_irq(struct bcm2835_host *host, u32 intmask) ++{ ++ log_event("IRQB", host->cmd, intmask); ++ if (!host->cmd) { ++ pr_err("%s: got command busy interrupt 0x%08x even " ++ "though no command operation was in progress.\n", ++ mmc_hostname(host->mmc), (unsigned)intmask); ++ bcm2835_sdhost_dumpregs(host); ++ return; ++ } ++ ++ if (!host->use_busy) { ++ pr_err("%s: got command busy interrupt 0x%08x even " ++ "though not expecting one.\n", ++ mmc_hostname(host->mmc), (unsigned)intmask); ++ bcm2835_sdhost_dumpregs(host); ++ return; ++ } ++ host->use_busy = 0; ++ ++ if (intmask & SDHSTS_ERROR_MASK) ++ { ++ pr_err("sdhost_busy_irq: intmask %x, data %p\n", intmask, host->mrq->data); ++ if (intmask & SDHSTS_CRC7_ERROR) ++ host->cmd->error = -EILSEQ; ++ else if (intmask & (SDHSTS_CRC16_ERROR | ++ SDHSTS_FIFO_ERROR)) { ++ if (host->mrq->data) ++ host->mrq->data->error = -EILSEQ; ++ else ++ host->cmd->error = -EILSEQ; ++ } else if (intmask & SDHSTS_REW_TIME_OUT) { ++ if (host->mrq->data) ++ host->mrq->data->error = -ETIMEDOUT; ++ else ++ host->cmd->error = -ETIMEDOUT; ++ } else if (intmask & SDHSTS_CMD_TIME_OUT) ++ host->cmd->error = -ETIMEDOUT; ++ ++ if (host->debug) { ++ log_dump(); ++ bcm2835_sdhost_dumpregs(host); ++ } ++ } ++ else ++ bcm2835_sdhost_finish_command(host, NULL); ++} ++ ++static void bcm2835_sdhost_data_irq(struct bcm2835_host *host, u32 intmask) ++{ ++ /* There are no dedicated data/space available interrupt ++ status bits, so it is necessary to use the single shared ++ data/space available FIFO status bits. It is therefore not ++ an error to get here when there is no data transfer in ++ progress. */ ++ log_event("IRQD", host->data, intmask); ++ if (!host->data) ++ return; ++ ++ if (intmask & (SDHSTS_CRC16_ERROR | ++ SDHSTS_FIFO_ERROR | ++ SDHSTS_REW_TIME_OUT)) { ++ if (intmask & (SDHSTS_CRC16_ERROR | ++ SDHSTS_FIFO_ERROR)) ++ host->data->error = -EILSEQ; ++ else ++ host->data->error = -ETIMEDOUT; ++ ++ if (host->debug) { ++ log_dump(); ++ bcm2835_sdhost_dumpregs(host); ++ } ++ } ++ ++ if (host->data->error) { ++ bcm2835_sdhost_finish_data(host); ++ } else if (host->data->flags & MMC_DATA_WRITE) { ++ /* Use the block interrupt for writes after the first block */ ++ host->hcfg &= ~(SDHCFG_DATA_IRPT_EN); ++ host->hcfg |= SDHCFG_BLOCK_IRPT_EN; ++ bcm2835_sdhost_write(host, host->hcfg, SDHCFG); ++ bcm2835_sdhost_transfer_pio(host); ++ } else { ++ bcm2835_sdhost_transfer_pio(host); ++ host->blocks--; ++ if ((host->blocks == 0) || host->data->error) ++ bcm2835_sdhost_finish_data(host); ++ } ++} ++ ++static void bcm2835_sdhost_block_irq(struct bcm2835_host *host, u32 intmask) ++{ ++ log_event("IRQK", host->data, intmask); ++ if (!host->data) { ++ pr_err("%s: got block interrupt 0x%08x even " ++ "though no data operation was in progress.\n", ++ mmc_hostname(host->mmc), (unsigned)intmask); ++ bcm2835_sdhost_dumpregs(host); ++ return; ++ } ++ ++ if (intmask & (SDHSTS_CRC16_ERROR | ++ SDHSTS_FIFO_ERROR | ++ SDHSTS_REW_TIME_OUT)) { ++ if (intmask & (SDHSTS_CRC16_ERROR | ++ SDHSTS_FIFO_ERROR)) ++ host->data->error = -EILSEQ; ++ else ++ host->data->error = -ETIMEDOUT; ++ ++ if (host->debug) { ++ log_dump(); ++ bcm2835_sdhost_dumpregs(host); ++ } ++ } ++ ++ if (!host->dma_desc) { ++ BUG_ON(!host->blocks); ++ if (host->data->error || (--host->blocks == 0)) { ++ bcm2835_sdhost_finish_data(host); ++ } else { ++ bcm2835_sdhost_transfer_pio(host); ++ } ++ } else if (host->data->flags & MMC_DATA_WRITE) { ++ bcm2835_sdhost_finish_data(host); ++ } ++} ++ ++static irqreturn_t bcm2835_sdhost_irq(int irq, void *dev_id) ++{ ++ irqreturn_t result = IRQ_NONE; ++ struct bcm2835_host *host = dev_id; ++ u32 intmask; ++ ++ spin_lock(&host->lock); ++ ++ intmask = bcm2835_sdhost_read(host, SDHSTS); ++ log_event("IRQ<", intmask, 0); ++ ++ bcm2835_sdhost_write(host, ++ SDHSTS_BUSY_IRPT | ++ SDHSTS_BLOCK_IRPT | ++ SDHSTS_SDIO_IRPT | ++ SDHSTS_DATA_FLAG, ++ SDHSTS); ++ ++ if (intmask & SDHSTS_BLOCK_IRPT) { ++ bcm2835_sdhost_block_irq(host, intmask); ++ result = IRQ_HANDLED; ++ } ++ ++ if (intmask & SDHSTS_BUSY_IRPT) { ++ bcm2835_sdhost_busy_irq(host, intmask); ++ result = IRQ_HANDLED; ++ } ++ ++ /* There is no true data interrupt status bit, so it is ++ necessary to qualify the data flag with the interrupt ++ enable bit */ ++ if ((intmask & SDHSTS_DATA_FLAG) && ++ (host->hcfg & SDHCFG_DATA_IRPT_EN)) { ++ bcm2835_sdhost_data_irq(host, intmask); ++ result = IRQ_HANDLED; ++ } ++ ++ log_event("IRQ>", bcm2835_sdhost_read(host, SDHSTS), 0); ++ spin_unlock(&host->lock); ++ ++ return result; ++} ++ ++void bcm2835_sdhost_set_clock(struct bcm2835_host *host, unsigned int clock) ++{ ++ int div = 0; /* Initialized for compiler warning */ ++ unsigned int input_clock = clock; ++ unsigned long flags; ++ ++ if (host->debug) ++ pr_info("%s: set_clock(%d)\n", mmc_hostname(host->mmc), clock); ++ ++ if (host->overclock_50 && (clock == 50*MHZ)) ++ clock = host->overclock_50 * MHZ + (MHZ - 1); ++ ++ /* The SDCDIV register has 11 bits, and holds (div - 2). ++ But in data mode the max is 50MHz wihout a minimum, and only the ++ bottom 3 bits are used. Since the switch over is automatic (unless ++ we have marked the card as slow...), chosen values have to make ++ sense in both modes. ++ Ident mode must be 100-400KHz, so can range check the requested ++ clock. CMD15 must be used to return to data mode, so this can be ++ monitored. ++ ++ clock 250MHz -> 0->125MHz, 1->83.3MHz, 2->62.5MHz, 3->50.0MHz ++ 4->41.7MHz, 5->35.7MHz, 6->31.3MHz, 7->27.8MHz ++ ++ 623->400KHz/27.8MHz ++ reset value (507)->491159/50MHz ++ ++ BUT, the 3-bit clock divisor in data mode is too small if the ++ core clock is higher than 250MHz, so instead use the SLOW_CARD ++ configuration bit to force the use of the ident clock divisor ++ at all times. ++ */ ++ ++ host->mmc->actual_clock = 0; ++ ++ if (host->firmware_sets_cdiv) { ++ u32 msg[3] = { clock, 0, 0 }; ++ ++ rpi_firmware_property(rpi_firmware_get(NULL), ++ RPI_FIRMWARE_SET_SDHOST_CLOCK, ++ &msg, sizeof(msg)); ++ ++ clock = max(msg[1], msg[2]); ++ spin_lock_irqsave(&host->lock, flags); ++ } else { ++ spin_lock_irqsave(&host->lock, flags); ++ if (clock < 100000) { ++ /* Can't stop the clock, but make it as slow as ++ * possible to show willing ++ */ ++ host->cdiv = SDCDIV_MAX_CDIV; ++ bcm2835_sdhost_write(host, host->cdiv, SDCDIV); ++ spin_unlock_irqrestore(&host->lock, flags); ++ return; ++ } ++ ++ div = host->max_clk / clock; ++ if (div < 2) ++ div = 2; ++ if ((host->max_clk / div) > clock) ++ div++; ++ div -= 2; ++ ++ if (div > SDCDIV_MAX_CDIV) ++ div = SDCDIV_MAX_CDIV; ++ ++ clock = host->max_clk / (div + 2); ++ ++ host->cdiv = div; ++ bcm2835_sdhost_write(host, host->cdiv, SDCDIV); ++ ++ if (host->debug) ++ pr_info("%s: clock=%d -> max_clk=%d, cdiv=%x " ++ "(actual clock %d)\n", ++ mmc_hostname(host->mmc), input_clock, ++ host->max_clk, host->cdiv, ++ clock); ++ } ++ ++ /* Calibrate some delays */ ++ ++ host->ns_per_fifo_word = (1000000000/clock) * ++ ((host->mmc->caps & MMC_CAP_4_BIT_DATA) ? 8 : 32); ++ ++ if (input_clock == 50 * MHZ) { ++ if (clock > input_clock) { ++ /* Save the closest value, to make it easier ++ to reduce in the event of error */ ++ host->overclock_50 = (clock/MHZ); ++ ++ if (clock != host->overclock) { ++ pr_info("%s: overclocking to %dHz\n", ++ mmc_hostname(host->mmc), clock); ++ host->overclock = clock; ++ } ++ } else if (host->overclock) { ++ host->overclock = 0; ++ if (clock == 50 * MHZ) ++ pr_warn("%s: cancelling overclock\n", ++ mmc_hostname(host->mmc)); ++ } ++ } else if (input_clock == 0) { ++ /* Reset the preferred overclock when the clock is stopped. ++ * This always happens during initialisation. */ ++ host->overclock_50 = host->user_overclock_50; ++ host->overclock = 0; ++ } ++ ++ /* Set the timeout to 500ms */ ++ bcm2835_sdhost_write(host, clock/2, SDTOUT); ++ ++ host->mmc->actual_clock = clock; ++ host->clock = input_clock; ++ host->reset_clock = 0; ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static void bcm2835_sdhost_request(struct mmc_host *mmc, struct mmc_request *mrq) ++{ ++ struct bcm2835_host *host; ++ unsigned long flags; ++ u32 edm, fsm; ++ ++ host = mmc_priv(mmc); ++ ++ if (host->debug) { ++ struct mmc_command *cmd = mrq->cmd; ++ BUG_ON(!cmd); ++ if (cmd->data) ++ pr_info("%s: cmd %d 0x%x (flags 0x%x) - %s %d*%d\n", ++ mmc_hostname(mmc), ++ cmd->opcode, cmd->arg, cmd->flags, ++ (cmd->data->flags & MMC_DATA_READ) ? ++ "read" : "write", cmd->data->blocks, ++ cmd->data->blksz); ++ else ++ pr_info("%s: cmd %d 0x%x (flags 0x%x)\n", ++ mmc_hostname(mmc), ++ cmd->opcode, cmd->arg, cmd->flags); ++ } ++ ++ /* Reset the error statuses in case this is a retry */ ++ if (mrq->sbc) ++ mrq->sbc->error = 0; ++ if (mrq->cmd) ++ mrq->cmd->error = 0; ++ if (mrq->data) ++ mrq->data->error = 0; ++ if (mrq->stop) ++ mrq->stop->error = 0; ++ ++ if (mrq->data && !is_power_of_2(mrq->data->blksz)) { ++ pr_err("%s: unsupported block size (%d bytes)\n", ++ mmc_hostname(mmc), mrq->data->blksz); ++ mrq->cmd->error = -EINVAL; ++ mmc_request_done(mmc, mrq); ++ return; ++ } ++ ++ if (host->use_dma && mrq->data && ++ (mrq->data->blocks > host->pio_limit)) ++ bcm2835_sdhost_prepare_dma(host, mrq->data); ++ ++ if (host->reset_clock) ++ bcm2835_sdhost_set_clock(host, host->clock); ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ WARN_ON(host->mrq != NULL); ++ host->mrq = mrq; ++ ++ edm = bcm2835_sdhost_read(host, SDEDM); ++ fsm = edm & SDEDM_FSM_MASK; ++ ++ log_event("REQ<", mrq, edm); ++ if ((fsm != SDEDM_FSM_IDENTMODE) && ++ (fsm != SDEDM_FSM_DATAMODE)) { ++ log_event("REQ!", mrq, edm); ++ if (host->debug) { ++ pr_warn("%s: previous command (%d) not complete (EDM %x)\n", ++ mmc_hostname(host->mmc), ++ bcm2835_sdhost_read(host, SDCMD) & SDCMD_CMD_MASK, ++ edm); ++ log_dump(); ++ bcm2835_sdhost_dumpregs(host); ++ } ++ mrq->cmd->error = -EILSEQ; ++ tasklet_schedule(&host->finish_tasklet); ++ spin_unlock_irqrestore(&host->lock, flags); ++ return; ++ } ++ ++ host->use_sbc = !!mrq->sbc && ++ (host->mrq->data->flags & USE_CMD23_FLAGS); ++ if (host->use_sbc) { ++ if (bcm2835_sdhost_send_command(host, mrq->sbc)) { ++ if (!host->use_busy) ++ bcm2835_sdhost_finish_command(host, &flags); ++ } ++ } else if (bcm2835_sdhost_send_command(host, mrq->cmd)) { ++ if (host->data && host->dma_desc) ++ /* DMA transfer starts now, PIO starts after irq */ ++ bcm2835_sdhost_start_dma(host); ++ ++ if (!host->use_busy) ++ bcm2835_sdhost_finish_command(host, &flags); ++ } ++ ++ log_event("CMD ", mrq->cmd->opcode, ++ mrq->data ? (u32)mrq->data->blksz : 0); ++ ++ log_event("REQ>", mrq, 0); ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static void bcm2835_sdhost_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) ++{ ++ ++ struct bcm2835_host *host = mmc_priv(mmc); ++ unsigned long flags; ++ ++ if (host->debug) ++ pr_info("%s: ios clock %d, pwr %d, bus_width %d, " ++ "timing %d, vdd %d, drv_type %d\n", ++ mmc_hostname(mmc), ++ ios->clock, ios->power_mode, ios->bus_width, ++ ios->timing, ios->signal_voltage, ios->drv_type); ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ log_event("IOS<", ios->clock, 0); ++ ++ /* set bus width */ ++ host->hcfg &= ~SDHCFG_WIDE_EXT_BUS; ++ if (ios->bus_width == MMC_BUS_WIDTH_4) ++ host->hcfg |= SDHCFG_WIDE_EXT_BUS; ++ ++ host->hcfg |= SDHCFG_WIDE_INT_BUS; ++ ++ /* Disable clever clock switching, to cope with fast core clocks */ ++ host->hcfg |= SDHCFG_SLOW_CARD; ++ ++ bcm2835_sdhost_write(host, host->hcfg, SDHCFG); ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++ ++ if (!ios->clock || ios->clock != host->clock) ++ bcm2835_sdhost_set_clock(host, ios->clock); ++} ++ ++static struct mmc_host_ops bcm2835_sdhost_ops = { ++ .request = bcm2835_sdhost_request, ++ .set_ios = bcm2835_sdhost_set_ios, ++ .hw_reset = bcm2835_sdhost_reset, ++}; ++ ++static void bcm2835_sdhost_cmd_wait_work(struct work_struct *work) ++{ ++ struct bcm2835_host *host; ++ unsigned long flags; ++ ++ host = container_of(work, struct bcm2835_host, cmd_wait_wq); ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ log_event("CWK<", host->cmd, host->mrq); ++ ++ /* ++ * If this tasklet gets rescheduled while running, it will ++ * be run again afterwards but without any active request. ++ */ ++ if (!host->mrq) { ++ spin_unlock_irqrestore(&host->lock, flags); ++ return; ++ } ++ ++ bcm2835_sdhost_finish_command(host, &flags); ++ ++ log_event("CWK>", host->cmd, 0); ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++} ++ ++static void bcm2835_sdhost_tasklet_finish(unsigned long param) ++{ ++ struct bcm2835_host *host; ++ unsigned long flags; ++ struct mmc_request *mrq; ++ struct dma_chan *terminate_chan = NULL; ++ ++ host = (struct bcm2835_host *)param; ++ ++ spin_lock_irqsave(&host->lock, flags); ++ ++ log_event("TSK<", host->mrq, 0); ++ /* ++ * If this tasklet gets rescheduled while running, it will ++ * be run again afterwards but without any active request. ++ */ ++ if (!host->mrq) { ++ spin_unlock_irqrestore(&host->lock, flags); ++ return; ++ } ++ ++ del_timer(&host->timer); ++ ++ mrq = host->mrq; ++ ++ /* Drop the overclock after any data corruption, or after any ++ * error while overclocked. Ignore errors for status commands, ++ * as they are likely when a card is ejected. */ ++ if (host->overclock) { ++ if ((mrq->cmd && mrq->cmd->error && ++ (mrq->cmd->opcode != MMC_SEND_STATUS)) || ++ (mrq->data && mrq->data->error) || ++ (mrq->stop && mrq->stop->error) || ++ (mrq->sbc && mrq->sbc->error)) { ++ host->overclock_50--; ++ pr_warn("%s: reducing overclock due to errors\n", ++ mmc_hostname(host->mmc)); ++ host->reset_clock = 1; ++ mrq->cmd->error = -ETIMEDOUT; ++ mrq->cmd->retries = 1; ++ } ++ } ++ ++ host->mrq = NULL; ++ host->cmd = NULL; ++ host->data = NULL; ++ ++ host->dma_desc = NULL; ++ terminate_chan = host->dma_chan; ++ host->dma_chan = NULL; ++ ++ spin_unlock_irqrestore(&host->lock, flags); ++ ++ if (terminate_chan) ++ { ++ int err = dmaengine_terminate_all(terminate_chan); ++ if (err) ++ pr_err("%s: failed to terminate DMA (%d)\n", ++ mmc_hostname(host->mmc), err); ++ } ++ ++ /* The SDHOST block doesn't report any errors for a disconnected ++ interface. All cards and SDIO devices should report some supported ++ voltage range, so a zero response to SEND_OP_COND, IO_SEND_OP_COND ++ or APP_SEND_OP_COND can be treated as an error. */ ++ if (((mrq->cmd->opcode == MMC_SEND_OP_COND) || ++ (mrq->cmd->opcode == SD_IO_SEND_OP_COND) || ++ (mrq->cmd->opcode == SD_APP_OP_COND)) && ++ (mrq->cmd->error == 0) && ++ (mrq->cmd->resp[0] == 0)) { ++ mrq->cmd->error = -ETIMEDOUT; ++ if (host->debug) ++ pr_info("%s: faking timeout due to zero OCR\n", ++ mmc_hostname(host->mmc)); ++ } ++ ++ mmc_request_done(host->mmc, mrq); ++ log_event("TSK>", mrq, 0); ++} ++ ++int bcm2835_sdhost_add_host(struct bcm2835_host *host) ++{ ++ struct mmc_host *mmc; ++ struct dma_slave_config cfg; ++ char pio_limit_string[20]; ++ int ret; ++ ++ mmc = host->mmc; ++ ++ if (!mmc->f_max || mmc->f_max > host->max_clk) ++ mmc->f_max = host->max_clk; ++ mmc->f_min = host->max_clk / SDCDIV_MAX_CDIV; ++ ++ mmc->max_busy_timeout = (~(unsigned int)0)/(mmc->f_max/1000); ++ ++ pr_debug("f_max %d, f_min %d, max_busy_timeout %d\n", ++ mmc->f_max, mmc->f_min, mmc->max_busy_timeout); ++ ++ /* host controller capabilities */ ++ mmc->caps |= ++ MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED | ++ MMC_CAP_NEEDS_POLL | MMC_CAP_HW_RESET | ++ ((ALLOW_CMD23_READ|ALLOW_CMD23_WRITE) * MMC_CAP_CMD23); ++ ++ spin_lock_init(&host->lock); ++ ++ if (host->allow_dma) { ++ if (IS_ERR_OR_NULL(host->dma_chan_rxtx)) { ++ pr_err("%s: unable to initialise DMA channel. " ++ "Falling back to PIO\n", ++ mmc_hostname(mmc)); ++ host->use_dma = false; ++ } else { ++ cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; ++ cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; ++ cfg.slave_id = 13; /* DREQ channel */ ++ ++ /* Validate the slave configurations */ ++ ++ cfg.direction = DMA_MEM_TO_DEV; ++ cfg.src_addr = 0; ++ cfg.dst_addr = host->bus_addr + SDDATA; ++ ++ ret = dmaengine_slave_config(host->dma_chan_rxtx, &cfg); ++ ++ if (ret == 0) { ++ host->dma_cfg_tx = cfg; ++ ++ cfg.direction = DMA_DEV_TO_MEM; ++ cfg.src_addr = host->bus_addr + SDDATA; ++ cfg.dst_addr = 0; ++ ++ ret = dmaengine_slave_config(host->dma_chan_rxtx, &cfg); ++ } ++ ++ if (ret == 0) { ++ host->dma_cfg_rx = cfg; ++ ++ host->use_dma = true; ++ } else { ++ pr_err("%s: unable to configure DMA channel. " ++ "Falling back to PIO\n", ++ mmc_hostname(mmc)); ++ dma_release_channel(host->dma_chan_rxtx); ++ host->dma_chan_rxtx = NULL; ++ host->use_dma = false; ++ } ++ } ++ } else { ++ host->use_dma = false; ++ } ++ ++ mmc->max_segs = 128; ++ mmc->max_req_size = 524288; ++ mmc->max_seg_size = mmc->max_req_size; ++ mmc->max_blk_size = 512; ++ mmc->max_blk_count = 65535; ++ ++ /* report supported voltage ranges */ ++ mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; ++ ++ tasklet_init(&host->finish_tasklet, ++ bcm2835_sdhost_tasklet_finish, (unsigned long)host); ++ ++ INIT_WORK(&host->cmd_wait_wq, bcm2835_sdhost_cmd_wait_work); ++ ++ timer_setup(&host->timer, bcm2835_sdhost_timeout, 0); ++ ++ bcm2835_sdhost_init(host, 0); ++ ++ ret = request_irq(host->irq, bcm2835_sdhost_irq, 0 /*IRQF_SHARED*/, ++ mmc_hostname(mmc), host); ++ if (ret) { ++ pr_err("%s: failed to request IRQ %d: %d\n", ++ mmc_hostname(mmc), host->irq, ret); ++ goto untasklet; ++ } ++ ++ mmc_add_host(mmc); ++ ++ pio_limit_string[0] = '\0'; ++ if (host->use_dma && (host->pio_limit > 0)) ++ sprintf(pio_limit_string, " (>%d)", host->pio_limit); ++ pr_info("%s: %s loaded - DMA %s%s\n", ++ mmc_hostname(mmc), DRIVER_NAME, ++ host->use_dma ? "enabled" : "disabled", ++ pio_limit_string); ++ ++ return 0; ++ ++untasklet: ++ tasklet_kill(&host->finish_tasklet); ++ ++ return ret; ++} ++ ++static int bcm2835_sdhost_probe(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ struct device_node *node = dev->of_node; ++ struct clk *clk; ++ struct resource *iomem; ++ struct bcm2835_host *host; ++ struct mmc_host *mmc; ++ const __be32 *addr; ++ u32 msg[3]; ++ int na; ++ int ret; ++ ++ pr_debug("bcm2835_sdhost_probe\n"); ++ mmc = mmc_alloc_host(sizeof(*host), dev); ++ if (!mmc) ++ return -ENOMEM; ++ ++ mmc->ops = &bcm2835_sdhost_ops; ++ host = mmc_priv(mmc); ++ host->mmc = mmc; ++ host->pio_timeout = msecs_to_jiffies(500); ++ host->pio_limit = 1; ++ host->max_delay = 1; /* Warn if over 1ms */ ++ host->allow_dma = 1; ++ spin_lock_init(&host->lock); ++ ++ iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ host->ioaddr = devm_ioremap_resource(dev, iomem); ++ if (IS_ERR(host->ioaddr)) { ++ ret = PTR_ERR(host->ioaddr); ++ goto err; ++ } ++ ++ na = of_n_addr_cells(node); ++ addr = of_get_address(node, 0, NULL, NULL); ++ if (!addr) { ++ dev_err(dev, "could not get DMA-register address\n"); ++ return -ENODEV; ++ } ++ host->bus_addr = (phys_addr_t)of_read_number(addr, na); ++ pr_debug(" - ioaddr %lx, iomem->start %lx, bus_addr %lx\n", ++ (unsigned long)host->ioaddr, ++ (unsigned long)iomem->start, ++ (unsigned long)host->bus_addr); ++ ++ if (node) { ++ /* Read any custom properties */ ++ of_property_read_u32(node, ++ "brcm,delay-after-stop", ++ &host->delay_after_stop); ++ of_property_read_u32(node, ++ "brcm,overclock-50", ++ &host->user_overclock_50); ++ of_property_read_u32(node, ++ "brcm,pio-limit", ++ &host->pio_limit); ++ host->allow_dma = ++ !of_property_read_bool(node, "brcm,force-pio"); ++ host->debug = of_property_read_bool(node, "brcm,debug"); ++ } ++ ++ host->dma_chan = NULL; ++ host->dma_desc = NULL; ++ ++ /* Formally recognise the other way of disabling DMA */ ++ if (host->pio_limit == 0x7fffffff) ++ host->allow_dma = false; ++ ++ if (host->allow_dma) { ++ if (node) { ++ host->dma_chan_rxtx = ++ dma_request_slave_channel(dev, "rx-tx"); ++ if (!host->dma_chan_rxtx) ++ host->dma_chan_rxtx = ++ dma_request_slave_channel(dev, "tx"); ++ if (!host->dma_chan_rxtx) ++ host->dma_chan_rxtx = ++ dma_request_slave_channel(dev, "rx"); ++ } else { ++ dma_cap_mask_t mask; ++ ++ dma_cap_zero(mask); ++ /* we don't care about the channel, any would work */ ++ dma_cap_set(DMA_SLAVE, mask); ++ host->dma_chan_rxtx = ++ dma_request_channel(mask, NULL, NULL); ++ } ++ } ++ ++ clk = devm_clk_get(dev, NULL); ++ if (IS_ERR(clk)) { ++ ret = PTR_ERR(clk); ++ if (ret == -EPROBE_DEFER) ++ dev_info(dev, "could not get clk, deferring probe\n"); ++ else ++ dev_err(dev, "could not get clk\n"); ++ goto err; ++ } ++ ++ host->max_clk = clk_get_rate(clk); ++ ++ host->irq = platform_get_irq(pdev, 0); ++ if (host->irq <= 0) { ++ dev_err(dev, "get IRQ failed\n"); ++ ret = -EINVAL; ++ goto err; ++ } ++ ++ pr_debug(" - max_clk %lx, irq %d\n", ++ (unsigned long)host->max_clk, ++ (int)host->irq); ++ ++ log_init(dev, iomem->start - host->bus_addr); ++ ++ if (node) ++ mmc_of_parse(mmc); ++ else ++ mmc->caps |= MMC_CAP_4_BIT_DATA; ++ ++ msg[0] = 0; ++ msg[1] = ~0; ++ msg[2] = ~0; ++ ++ rpi_firmware_property(rpi_firmware_get(NULL), ++ RPI_FIRMWARE_SET_SDHOST_CLOCK, ++ &msg, sizeof(msg)); ++ ++ host->firmware_sets_cdiv = (msg[1] != ~0); ++ ++ ret = bcm2835_sdhost_add_host(host); ++ if (ret) ++ goto err; ++ ++ platform_set_drvdata(pdev, host); ++ ++ pr_debug("bcm2835_sdhost_probe -> OK\n"); ++ ++ return 0; ++ ++err: ++ pr_debug("bcm2835_sdhost_probe -> err %d\n", ret); ++ if (host->dma_chan_rxtx) ++ dma_release_channel(host->dma_chan_rxtx); ++ mmc_free_host(mmc); ++ ++ return ret; ++} ++ ++static int bcm2835_sdhost_remove(struct platform_device *pdev) ++{ ++ struct bcm2835_host *host = platform_get_drvdata(pdev); ++ ++ pr_debug("bcm2835_sdhost_remove\n"); ++ ++ mmc_remove_host(host->mmc); ++ ++ bcm2835_sdhost_set_power(host, false); ++ ++ free_irq(host->irq, host); ++ ++ del_timer_sync(&host->timer); ++ ++ tasklet_kill(&host->finish_tasklet); ++ if (host->dma_chan_rxtx) ++ dma_release_channel(host->dma_chan_rxtx); ++ mmc_free_host(host->mmc); ++ platform_set_drvdata(pdev, NULL); ++ ++ pr_debug("bcm2835_sdhost_remove - OK\n"); ++ return 0; ++} ++ ++static const struct of_device_id bcm2835_sdhost_match[] = { ++ { .compatible = "brcm,bcm2835-sdhost" }, ++ { } ++}; ++MODULE_DEVICE_TABLE(of, bcm2835_sdhost_match); ++ ++static struct platform_driver bcm2835_sdhost_driver = { ++ .probe = bcm2835_sdhost_probe, ++ .remove = bcm2835_sdhost_remove, ++ .driver = { ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ .of_match_table = bcm2835_sdhost_match, ++ }, ++}; ++module_platform_driver(bcm2835_sdhost_driver); ++ ++MODULE_ALIAS("platform:sdhost-bcm2835"); ++MODULE_DESCRIPTION("BCM2835 SDHost driver"); ++MODULE_LICENSE("GPL v2"); ++MODULE_AUTHOR("Phil Elwell"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0048-vc_mem-Add-vc_mem-driver-for-querying-firmware-memor.patch b/target/linux/bcm27xx/patches-5.10/950-0048-vc_mem-Add-vc_mem-driver-for-querying-firmware-memor.patch new file mode 100644 index 0000000000..902959a900 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0048-vc_mem-Add-vc_mem-driver-for-querying-firmware-memor.patch @@ -0,0 +1,488 @@ +From 156d50d2fb05f132d53927cbf9fad3c9c37e8937 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Fri, 28 Oct 2016 15:36:43 +0100 +Subject: [PATCH] vc_mem: Add vc_mem driver for querying firmware + memory addresses +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Signed-off-by: popcornmix + +BCM270x: Move vc_mem + +Make the vc_mem module available for ARCH_BCM2835 by moving it. + +Signed-off-by: Noralf Trønnes + +char: vc_mem: Fix up compat ioctls for 64bit kernel + +compat_ioctl wasn't defined, so 32bit user/64bit kernel +always failed. +VC_MEM_IOC_MEM_PHYS_ADDR was defined with parameter size +unsigned long, so the ioctl cmd changes between sizes. + +Signed-off-by: Dave Stevenson + +char: vc_mem: Fix all coding style issues. + +Cleans up all checkpatch errors in vc_mem.c and vc_mem.h +No functional change to the code. + +Signed-off-by: Dave Stevenson +--- + drivers/char/broadcom/Kconfig | 18 ++ + drivers/char/broadcom/Makefile | 1 + + drivers/char/broadcom/vc_mem.c | 375 ++++++++++++++++++++++++++++++++ + include/linux/broadcom/vc_mem.h | 39 ++++ + 4 files changed, 433 insertions(+) + create mode 100644 drivers/char/broadcom/Kconfig + create mode 100644 drivers/char/broadcom/Makefile + create mode 100644 drivers/char/broadcom/vc_mem.c + create mode 100644 include/linux/broadcom/vc_mem.h + +--- /dev/null ++++ b/drivers/char/broadcom/Kconfig +@@ -0,0 +1,18 @@ ++# ++# Broadcom char driver config ++# ++ ++menuconfig BRCM_CHAR_DRIVERS ++ bool "Broadcom Char Drivers" ++ help ++ Broadcom's char drivers ++ ++if BRCM_CHAR_DRIVERS ++ ++config BCM2708_VCMEM ++ bool "Videocore Memory" ++ default y ++ help ++ Helper for videocore memory access and total size allocation. ++ ++endif +--- /dev/null ++++ b/drivers/char/broadcom/Makefile +@@ -0,0 +1 @@ ++obj-$(CONFIG_BCM2708_VCMEM) += vc_mem.o +--- /dev/null ++++ b/drivers/char/broadcom/vc_mem.c +@@ -0,0 +1,375 @@ ++/* ++ * Copyright 2010 - 2011 Broadcom Corporation. All rights reserved. ++ * ++ * Unless you and Broadcom execute a separate written software license ++ * agreement governing use of this software, this software is licensed to you ++ * under the terms of the GNU General Public License version 2, available at ++ * http://www.broadcom.com/licenses/GPLv2.php (the "GPL"). ++ * ++ * Notwithstanding the above, under no circumstances may you combine this ++ * software in any way with any other Broadcom software provided under a ++ * license other than the GPL, without Broadcom's express prior written ++ * consent. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define DRIVER_NAME "vc-mem" ++ ++/* Device (/dev) related variables */ ++static dev_t vc_mem_devnum; ++static struct class *vc_mem_class; ++static struct cdev vc_mem_cdev; ++static int vc_mem_inited; ++ ++#ifdef CONFIG_DEBUG_FS ++static struct dentry *vc_mem_debugfs_entry; ++#endif ++ ++/* ++ * Videocore memory addresses and size ++ * ++ * Drivers that wish to know the videocore memory addresses and sizes should ++ * use these variables instead of the MM_IO_BASE and MM_ADDR_IO defines in ++ * headers. This allows the other drivers to not be tied down to a a certain ++ * address/size at compile time. ++ * ++ * In the future, the goal is to have the videocore memory virtual address and ++ * size be calculated at boot time rather than at compile time. The decision of ++ * where the videocore memory resides and its size would be in the hands of the ++ * bootloader (and/or kernel). When that happens, the values of these variables ++ * would be calculated and assigned in the init function. ++ */ ++/* In the 2835 VC in mapped above ARM, but ARM has full access to VC space */ ++unsigned long mm_vc_mem_phys_addr; ++EXPORT_SYMBOL(mm_vc_mem_phys_addr); ++unsigned int mm_vc_mem_size; ++EXPORT_SYMBOL(mm_vc_mem_size); ++unsigned int mm_vc_mem_base; ++EXPORT_SYMBOL(mm_vc_mem_base); ++ ++static uint phys_addr; ++static uint mem_size; ++static uint mem_base; ++ ++static int ++vc_mem_open(struct inode *inode, struct file *file) ++{ ++ (void)inode; ++ ++ pr_debug("%s: called file = 0x%p\n", __func__, file); ++ ++ return 0; ++} ++ ++static int ++vc_mem_release(struct inode *inode, struct file *file) ++{ ++ (void)inode; ++ ++ pr_debug("%s: called file = 0x%p\n", __func__, file); ++ ++ return 0; ++} ++ ++static void ++vc_mem_get_size(void) ++{ ++} ++ ++static void ++vc_mem_get_base(void) ++{ ++} ++ ++int ++vc_mem_get_current_size(void) ++{ ++ return mm_vc_mem_size; ++} ++EXPORT_SYMBOL_GPL(vc_mem_get_current_size); ++ ++static long ++vc_mem_ioctl(struct file *file, unsigned int cmd, unsigned long arg) ++{ ++ int rc = 0; ++ ++ (void) cmd; ++ (void) arg; ++ ++ pr_debug("%s: called file = 0x%p, cmd %08x\n", __func__, file, cmd); ++ ++ switch (cmd) { ++ case VC_MEM_IOC_MEM_PHYS_ADDR: ++ { ++ pr_debug("%s: VC_MEM_IOC_MEM_PHYS_ADDR=0x%p\n", ++ __func__, (void *)mm_vc_mem_phys_addr); ++ ++ if (copy_to_user((void *)arg, &mm_vc_mem_phys_addr, ++ sizeof(mm_vc_mem_phys_addr))) { ++ rc = -EFAULT; ++ } ++ break; ++ } ++ case VC_MEM_IOC_MEM_SIZE: ++ { ++ /* Get the videocore memory size first */ ++ vc_mem_get_size(); ++ ++ pr_debug("%s: VC_MEM_IOC_MEM_SIZE=%x\n", __func__, ++ mm_vc_mem_size); ++ ++ if (copy_to_user((void *)arg, &mm_vc_mem_size, ++ sizeof(mm_vc_mem_size))) { ++ rc = -EFAULT; ++ } ++ break; ++ } ++ case VC_MEM_IOC_MEM_BASE: ++ { ++ /* Get the videocore memory base */ ++ vc_mem_get_base(); ++ ++ pr_debug("%s: VC_MEM_IOC_MEM_BASE=%x\n", __func__, ++ mm_vc_mem_base); ++ ++ if (copy_to_user((void *)arg, &mm_vc_mem_base, ++ sizeof(mm_vc_mem_base))) { ++ rc = -EFAULT; ++ } ++ break; ++ } ++ case VC_MEM_IOC_MEM_LOAD: ++ { ++ /* Get the videocore memory base */ ++ vc_mem_get_base(); ++ ++ pr_debug("%s: VC_MEM_IOC_MEM_LOAD=%x\n", __func__, ++ mm_vc_mem_base); ++ ++ if (copy_to_user((void *)arg, &mm_vc_mem_base, ++ sizeof(mm_vc_mem_base))) { ++ rc = -EFAULT; ++ } ++ break; ++ } ++ default: ++ { ++ return -ENOTTY; ++ } ++ } ++ pr_debug("%s: file = 0x%p returning %d\n", __func__, file, rc); ++ ++ return rc; ++} ++ ++#ifdef CONFIG_COMPAT ++static long ++vc_mem_compat_ioctl(struct file *file, unsigned int cmd, unsigned long arg) ++{ ++ int rc = 0; ++ ++ switch (cmd) { ++ case VC_MEM_IOC_MEM_PHYS_ADDR32: ++ pr_debug("%s: VC_MEM_IOC_MEM_PHYS_ADDR32=0x%p\n", ++ __func__, (void *)mm_vc_mem_phys_addr); ++ ++ /* This isn't correct, but will cover us for now as ++ * VideoCore is 32bit only. ++ */ ++ if (copy_to_user((void *)arg, &mm_vc_mem_phys_addr, ++ sizeof(compat_ulong_t))) ++ rc = -EFAULT; ++ ++ break; ++ ++ default: ++ rc = vc_mem_ioctl(file, cmd, arg); ++ break; ++ } ++ ++ return rc; ++} ++#endif ++ ++static int ++vc_mem_mmap(struct file *filp, struct vm_area_struct *vma) ++{ ++ int rc = 0; ++ unsigned long length = vma->vm_end - vma->vm_start; ++ unsigned long offset = vma->vm_pgoff << PAGE_SHIFT; ++ ++ pr_debug("%s: vm_start = 0x%08lx vm_end = 0x%08lx vm_pgoff = 0x%08lx\n", ++ __func__, (long)vma->vm_start, (long)vma->vm_end, ++ (long)vma->vm_pgoff); ++ ++ if (offset + length > mm_vc_mem_size) { ++ pr_err("%s: length %ld is too big\n", __func__, length); ++ return -EINVAL; ++ } ++ /* Do not cache the memory map */ ++ vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot); ++ ++ rc = remap_pfn_range(vma, vma->vm_start, ++ (mm_vc_mem_phys_addr >> PAGE_SHIFT) + ++ vma->vm_pgoff, length, vma->vm_page_prot); ++ if (rc) ++ pr_err("%s: remap_pfn_range failed (rc=%d)\n", __func__, rc); ++ ++ return rc; ++} ++ ++/* File Operations for the driver. */ ++static const struct file_operations vc_mem_fops = { ++ .owner = THIS_MODULE, ++ .open = vc_mem_open, ++ .release = vc_mem_release, ++ .unlocked_ioctl = vc_mem_ioctl, ++#ifdef CONFIG_COMPAT ++ .compat_ioctl = vc_mem_compat_ioctl, ++#endif ++ .mmap = vc_mem_mmap, ++}; ++ ++#ifdef CONFIG_DEBUG_FS ++static void vc_mem_debugfs_deinit(void) ++{ ++ debugfs_remove_recursive(vc_mem_debugfs_entry); ++ vc_mem_debugfs_entry = NULL; ++} ++ ++ ++static int vc_mem_debugfs_init( ++ struct device *dev) ++{ ++ vc_mem_debugfs_entry = debugfs_create_dir(DRIVER_NAME, NULL); ++ if (!vc_mem_debugfs_entry) { ++ dev_warn(dev, "could not create debugfs entry\n"); ++ return -EFAULT; ++ } ++ ++ debugfs_create_x32("vc_mem_phys_addr", ++ 0444, ++ vc_mem_debugfs_entry, ++ (u32 *)&mm_vc_mem_phys_addr); ++ debugfs_create_x32("vc_mem_size", ++ 0444, ++ vc_mem_debugfs_entry, ++ (u32 *)&mm_vc_mem_size); ++ debugfs_create_x32("vc_mem_base", ++ 0444, ++ vc_mem_debugfs_entry, ++ (u32 *)&mm_vc_mem_base); ++ ++ return 0; ++} ++ ++#endif /* CONFIG_DEBUG_FS */ ++ ++/* Module load/unload functions */ ++ ++static int __init ++vc_mem_init(void) ++{ ++ int rc = -EFAULT; ++ struct device *dev; ++ ++ pr_debug("%s: called\n", __func__); ++ ++ mm_vc_mem_phys_addr = phys_addr; ++ mm_vc_mem_size = mem_size; ++ mm_vc_mem_base = mem_base; ++ ++ vc_mem_get_size(); ++ ++ pr_info("vc-mem: phys_addr:0x%08lx mem_base=0x%08x mem_size:0x%08x(%u MiB)\n", ++ mm_vc_mem_phys_addr, mm_vc_mem_base, mm_vc_mem_size, ++ mm_vc_mem_size / (1024 * 1024)); ++ ++ rc = alloc_chrdev_region(&vc_mem_devnum, 0, 1, DRIVER_NAME); ++ if (rc < 0) { ++ pr_err("%s: alloc_chrdev_region failed (rc=%d)\n", ++ __func__, rc); ++ goto out_err; ++ } ++ ++ cdev_init(&vc_mem_cdev, &vc_mem_fops); ++ rc = cdev_add(&vc_mem_cdev, vc_mem_devnum, 1); ++ if (rc) { ++ pr_err("%s: cdev_add failed (rc=%d)\n", __func__, rc); ++ goto out_unregister; ++ } ++ ++ vc_mem_class = class_create(THIS_MODULE, DRIVER_NAME); ++ if (IS_ERR(vc_mem_class)) { ++ rc = PTR_ERR(vc_mem_class); ++ pr_err("%s: class_create failed (rc=%d)\n", __func__, rc); ++ goto out_cdev_del; ++ } ++ ++ dev = device_create(vc_mem_class, NULL, vc_mem_devnum, NULL, ++ DRIVER_NAME); ++ if (IS_ERR(dev)) { ++ rc = PTR_ERR(dev); ++ pr_err("%s: device_create failed (rc=%d)\n", __func__, rc); ++ goto out_class_destroy; ++ } ++ ++#ifdef CONFIG_DEBUG_FS ++ /* don't fail if the debug entries cannot be created */ ++ vc_mem_debugfs_init(dev); ++#endif ++ ++ vc_mem_inited = 1; ++ return 0; ++ ++ device_destroy(vc_mem_class, vc_mem_devnum); ++ ++out_class_destroy: ++ class_destroy(vc_mem_class); ++ vc_mem_class = NULL; ++ ++out_cdev_del: ++ cdev_del(&vc_mem_cdev); ++ ++out_unregister: ++ unregister_chrdev_region(vc_mem_devnum, 1); ++ ++out_err: ++ return -1; ++} ++ ++static void __exit ++vc_mem_exit(void) ++{ ++ pr_debug("%s: called\n", __func__); ++ ++ if (vc_mem_inited) { ++#if CONFIG_DEBUG_FS ++ vc_mem_debugfs_deinit(); ++#endif ++ device_destroy(vc_mem_class, vc_mem_devnum); ++ class_destroy(vc_mem_class); ++ cdev_del(&vc_mem_cdev); ++ unregister_chrdev_region(vc_mem_devnum, 1); ++ } ++} ++ ++module_init(vc_mem_init); ++module_exit(vc_mem_exit); ++MODULE_LICENSE("GPL"); ++MODULE_AUTHOR("Broadcom Corporation"); ++ ++module_param(phys_addr, uint, 0644); ++module_param(mem_size, uint, 0644); ++module_param(mem_base, uint, 0644); +--- /dev/null ++++ b/include/linux/broadcom/vc_mem.h +@@ -0,0 +1,39 @@ ++/* ++ * Copyright 2010 - 2011 Broadcom Corporation. All rights reserved. ++ * ++ * Unless you and Broadcom execute a separate written software license ++ * agreement governing use of this software, this software is licensed to you ++ * under the terms of the GNU General Public License version 2, available at ++ * http://www.broadcom.com/licenses/GPLv2.php (the "GPL"). ++ * ++ * Notwithstanding the above, under no circumstances may you combine this ++ * software in any way with any other Broadcom software provided under a ++ * license other than the GPL, without Broadcom's express prior written ++ * consent. ++ */ ++ ++#ifndef _VC_MEM_H ++#define _VC_MEM_H ++ ++#include ++ ++#define VC_MEM_IOC_MAGIC 'v' ++ ++#define VC_MEM_IOC_MEM_PHYS_ADDR _IOR(VC_MEM_IOC_MAGIC, 0, unsigned long) ++#define VC_MEM_IOC_MEM_SIZE _IOR(VC_MEM_IOC_MAGIC, 1, unsigned int) ++#define VC_MEM_IOC_MEM_BASE _IOR(VC_MEM_IOC_MAGIC, 2, unsigned int) ++#define VC_MEM_IOC_MEM_LOAD _IOR(VC_MEM_IOC_MAGIC, 3, unsigned int) ++ ++#ifdef __KERNEL__ ++#define VC_MEM_TO_ARM_ADDR_MASK 0x3FFFFFFF ++ ++extern unsigned long mm_vc_mem_phys_addr; ++extern unsigned int mm_vc_mem_size; ++extern int vc_mem_get_current_size(void); ++#endif ++ ++#ifdef CONFIG_COMPAT ++#define VC_MEM_IOC_MEM_PHYS_ADDR32 _IOR(VC_MEM_IOC_MAGIC, 0, compat_ulong_t) ++#endif ++ ++#endif /* _VC_MEM_H */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0049-Add-dev-gpiomem-device-for-rootless-user-GPIO-access.patch b/target/linux/bcm27xx/patches-5.10/950-0049-Add-dev-gpiomem-device-for-rootless-user-GPIO-access.patch new file mode 100644 index 0000000000..4b4a7df97b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0049-Add-dev-gpiomem-device-for-rootless-user-GPIO-access.patch @@ -0,0 +1,299 @@ +From 09897ac552d99d483131bcf107866ac2dc51694f Mon Sep 17 00:00:00 2001 +From: Luke Wren +Date: Fri, 21 Aug 2015 23:14:48 +0100 +Subject: [PATCH] Add /dev/gpiomem device for rootless user GPIO access + +Signed-off-by: Luke Wren + +bcm2835-gpiomem: Fix for ARCH_BCM2835 builds + +Build on ARCH_BCM2835, and fail to probe if no IO resource. + +See: https://github.com/raspberrypi/linux/issues/1154 +--- + drivers/char/broadcom/Kconfig | 8 + + drivers/char/broadcom/Makefile | 1 + + drivers/char/broadcom/bcm2835-gpiomem.c | 258 ++++++++++++++++++++++++ + 3 files changed, 267 insertions(+) + create mode 100644 drivers/char/broadcom/bcm2835-gpiomem.c + +--- a/drivers/char/broadcom/Kconfig ++++ b/drivers/char/broadcom/Kconfig +@@ -16,3 +16,11 @@ config BCM2708_VCMEM + Helper for videocore memory access and total size allocation. + + endif ++ ++config BCM2835_DEVGPIOMEM ++ tristate "/dev/gpiomem rootless GPIO access via mmap() on the BCM2835" ++ default m ++ help ++ Provides users with root-free access to the GPIO registers ++ on the 2835. Calling mmap(/dev/gpiomem) will map the GPIO ++ register page to the user's pointer. +--- a/drivers/char/broadcom/Makefile ++++ b/drivers/char/broadcom/Makefile +@@ -1 +1,2 @@ + obj-$(CONFIG_BCM2708_VCMEM) += vc_mem.o ++obj-$(CONFIG_BCM2835_DEVGPIOMEM)+= bcm2835-gpiomem.o +--- /dev/null ++++ b/drivers/char/broadcom/bcm2835-gpiomem.c +@@ -0,0 +1,258 @@ ++/** ++ * GPIO memory device driver ++ * ++ * Creates a chardev /dev/gpiomem which will provide user access to ++ * the BCM2835's GPIO registers when it is mmap()'d. ++ * No longer need root for user GPIO access, but without relaxing permissions ++ * on /dev/mem. ++ * ++ * Written by Luke Wren ++ * Copyright (c) 2015, Raspberry Pi (Trading) Ltd. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions ++ * are met: ++ * 1. Redistributions of source code must retain the above copyright ++ * notice, this list of conditions, and the following disclaimer, ++ * without modification. ++ * 2. Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in the ++ * documentation and/or other materials provided with the distribution. ++ * 3. The names of the above-listed copyright holders may not be used ++ * to endorse or promote products derived from this software without ++ * specific prior written permission. ++ * ++ * ALTERNATIVELY, this software may be distributed under the terms of the ++ * GNU General Public License ("GPL") version 2, as published by the Free ++ * Software Foundation. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS ++ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ++ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR ++ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR ++ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF ++ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING ++ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define DEVICE_NAME "bcm2835-gpiomem" ++#define DRIVER_NAME "gpiomem-bcm2835" ++#define DEVICE_MINOR 0 ++ ++struct bcm2835_gpiomem_instance { ++ unsigned long gpio_regs_phys; ++ struct device *dev; ++}; ++ ++static struct cdev bcm2835_gpiomem_cdev; ++static dev_t bcm2835_gpiomem_devid; ++static struct class *bcm2835_gpiomem_class; ++static struct device *bcm2835_gpiomem_dev; ++static struct bcm2835_gpiomem_instance *inst; ++ ++ ++/**************************************************************************** ++* ++* GPIO mem chardev file ops ++* ++***************************************************************************/ ++ ++static int bcm2835_gpiomem_open(struct inode *inode, struct file *file) ++{ ++ int dev = iminor(inode); ++ int ret = 0; ++ ++ if (dev != DEVICE_MINOR) { ++ dev_err(inst->dev, "Unknown minor device: %d", dev); ++ ret = -ENXIO; ++ } ++ return ret; ++} ++ ++static int bcm2835_gpiomem_release(struct inode *inode, struct file *file) ++{ ++ int dev = iminor(inode); ++ int ret = 0; ++ ++ if (dev != DEVICE_MINOR) { ++ dev_err(inst->dev, "Unknown minor device %d", dev); ++ ret = -ENXIO; ++ } ++ return ret; ++} ++ ++static const struct vm_operations_struct bcm2835_gpiomem_vm_ops = { ++#ifdef CONFIG_HAVE_IOREMAP_PROT ++ .access = generic_access_phys ++#endif ++}; ++ ++static int bcm2835_gpiomem_mmap(struct file *file, struct vm_area_struct *vma) ++{ ++ /* Ignore what the user says - they're getting the GPIO regs ++ whether they like it or not! */ ++ unsigned long gpio_page = inst->gpio_regs_phys >> PAGE_SHIFT; ++ ++ vma->vm_page_prot = phys_mem_access_prot(file, gpio_page, ++ PAGE_SIZE, ++ vma->vm_page_prot); ++ vma->vm_ops = &bcm2835_gpiomem_vm_ops; ++ if (remap_pfn_range(vma, vma->vm_start, ++ gpio_page, ++ PAGE_SIZE, ++ vma->vm_page_prot)) { ++ return -EAGAIN; ++ } ++ return 0; ++} ++ ++static const struct file_operations ++bcm2835_gpiomem_fops = { ++ .owner = THIS_MODULE, ++ .open = bcm2835_gpiomem_open, ++ .release = bcm2835_gpiomem_release, ++ .mmap = bcm2835_gpiomem_mmap, ++}; ++ ++ ++ /**************************************************************************** ++* ++* Probe and remove functions ++* ++***************************************************************************/ ++ ++ ++static int bcm2835_gpiomem_probe(struct platform_device *pdev) ++{ ++ int err; ++ void *ptr_err; ++ struct device *dev = &pdev->dev; ++ struct resource *ioresource; ++ ++ /* Allocate buffers and instance data */ ++ ++ inst = kzalloc(sizeof(struct bcm2835_gpiomem_instance), GFP_KERNEL); ++ ++ if (!inst) { ++ err = -ENOMEM; ++ goto failed_inst_alloc; ++ } ++ ++ inst->dev = dev; ++ ++ ioresource = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ if (ioresource) { ++ inst->gpio_regs_phys = ioresource->start; ++ } else { ++ dev_err(inst->dev, "failed to get IO resource"); ++ err = -ENOENT; ++ goto failed_get_resource; ++ } ++ ++ /* Create character device entries */ ++ ++ err = alloc_chrdev_region(&bcm2835_gpiomem_devid, ++ DEVICE_MINOR, 1, DEVICE_NAME); ++ if (err != 0) { ++ dev_err(inst->dev, "unable to allocate device number"); ++ goto failed_alloc_chrdev; ++ } ++ cdev_init(&bcm2835_gpiomem_cdev, &bcm2835_gpiomem_fops); ++ bcm2835_gpiomem_cdev.owner = THIS_MODULE; ++ err = cdev_add(&bcm2835_gpiomem_cdev, bcm2835_gpiomem_devid, 1); ++ if (err != 0) { ++ dev_err(inst->dev, "unable to register device"); ++ goto failed_cdev_add; ++ } ++ ++ /* Create sysfs entries */ ++ ++ bcm2835_gpiomem_class = class_create(THIS_MODULE, DEVICE_NAME); ++ ptr_err = bcm2835_gpiomem_class; ++ if (IS_ERR(ptr_err)) ++ goto failed_class_create; ++ ++ bcm2835_gpiomem_dev = device_create(bcm2835_gpiomem_class, NULL, ++ bcm2835_gpiomem_devid, NULL, ++ "gpiomem"); ++ ptr_err = bcm2835_gpiomem_dev; ++ if (IS_ERR(ptr_err)) ++ goto failed_device_create; ++ ++ dev_info(inst->dev, "Initialised: Registers at 0x%08lx", ++ inst->gpio_regs_phys); ++ ++ return 0; ++ ++failed_device_create: ++ class_destroy(bcm2835_gpiomem_class); ++failed_class_create: ++ cdev_del(&bcm2835_gpiomem_cdev); ++ err = PTR_ERR(ptr_err); ++failed_cdev_add: ++ unregister_chrdev_region(bcm2835_gpiomem_devid, 1); ++failed_alloc_chrdev: ++failed_get_resource: ++ kfree(inst); ++failed_inst_alloc: ++ dev_err(inst->dev, "could not load bcm2835_gpiomem"); ++ return err; ++} ++ ++static int bcm2835_gpiomem_remove(struct platform_device *pdev) ++{ ++ struct device *dev = inst->dev; ++ ++ kfree(inst); ++ device_destroy(bcm2835_gpiomem_class, bcm2835_gpiomem_devid); ++ class_destroy(bcm2835_gpiomem_class); ++ cdev_del(&bcm2835_gpiomem_cdev); ++ unregister_chrdev_region(bcm2835_gpiomem_devid, 1); ++ ++ dev_info(dev, "GPIO mem driver removed - OK"); ++ return 0; ++} ++ ++ /**************************************************************************** ++* ++* Register the driver with device tree ++* ++***************************************************************************/ ++ ++static const struct of_device_id bcm2835_gpiomem_of_match[] = { ++ {.compatible = "brcm,bcm2835-gpiomem",}, ++ { /* sentinel */ }, ++}; ++ ++MODULE_DEVICE_TABLE(of, bcm2835_gpiomem_of_match); ++ ++static struct platform_driver bcm2835_gpiomem_driver = { ++ .probe = bcm2835_gpiomem_probe, ++ .remove = bcm2835_gpiomem_remove, ++ .driver = { ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ .of_match_table = bcm2835_gpiomem_of_match, ++ }, ++}; ++ ++module_platform_driver(bcm2835_gpiomem_driver); ++ ++MODULE_ALIAS("platform:gpiomem-bcm2835"); ++MODULE_LICENSE("GPL"); ++MODULE_DESCRIPTION("gpiomem driver for accessing GPIO from userspace"); ++MODULE_AUTHOR("Luke Wren "); diff --git a/target/linux/bcm27xx/patches-5.10/950-0050-Add-SMI-driver.patch b/target/linux/bcm27xx/patches-5.10/950-0050-Add-SMI-driver.patch new file mode 100644 index 0000000000..f1c3509f84 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0050-Add-SMI-driver.patch @@ -0,0 +1,1910 @@ +From 5d41827cef0a52089040b6edd311e5c0fdae1fc9 Mon Sep 17 00:00:00 2001 +From: Luke Wren +Date: Sat, 5 Sep 2015 01:14:45 +0100 +Subject: [PATCH] Add SMI driver + +Signed-off-by: Luke Wren + +MISC: bcm2835: smi: use clock manager and fix reload issues + +Use clock manager instead of self-made clockmanager. + +Also fix some error paths that showd up during development +(especially missing release of dma resources on rmmod) + +Signed-off-by: Martin Sperl + +bcm2835_smi: re-add dereference to fix DMA transfers +--- + .../bindings/misc/brcm,bcm2835-smi-dev.txt | 17 + + .../bindings/misc/brcm,bcm2835-smi.txt | 48 + + drivers/char/broadcom/Kconfig | 9 + + drivers/char/broadcom/Makefile | 1 + + drivers/char/broadcom/bcm2835_smi_dev.c | 402 ++++++++ + drivers/misc/Kconfig | 8 + + drivers/misc/Makefile | 1 + + drivers/misc/bcm2835_smi.c | 955 ++++++++++++++++++ + include/linux/broadcom/bcm2835_smi.h | 391 +++++++ + 9 files changed, 1832 insertions(+) + create mode 100644 Documentation/devicetree/bindings/misc/brcm,bcm2835-smi-dev.txt + create mode 100644 Documentation/devicetree/bindings/misc/brcm,bcm2835-smi.txt + create mode 100644 drivers/char/broadcom/bcm2835_smi_dev.c + create mode 100644 drivers/misc/bcm2835_smi.c + create mode 100644 include/linux/broadcom/bcm2835_smi.h + +--- /dev/null ++++ b/Documentation/devicetree/bindings/misc/brcm,bcm2835-smi-dev.txt +@@ -0,0 +1,17 @@ ++* Broadcom BCM2835 SMI character device driver. ++ ++SMI or secondary memory interface is a peripheral specific to certain Broadcom ++SOCs, and is helpful for talking to things like parallel-interface displays ++and NAND flashes (in fact, most things with a parallel register interface). ++ ++This driver adds a character device which provides a user-space interface to ++an instance of the SMI driver. ++ ++Required properties: ++- compatible: "brcm,bcm2835-smi-dev" ++- smi_handle: a phandle to the smi node. ++ ++Optional properties: ++- None. ++ ++ +--- /dev/null ++++ b/Documentation/devicetree/bindings/misc/brcm,bcm2835-smi.txt +@@ -0,0 +1,48 @@ ++* Broadcom BCM2835 SMI driver. ++ ++SMI or secondary memory interface is a peripheral specific to certain Broadcom ++SOCs, and is helpful for talking to things like parallel-interface displays ++and NAND flashes (in fact, most things with a parallel register interface). ++ ++Required properties: ++- compatible: "brcm,bcm2835-smi" ++- reg: Should contain location and length of SMI registers and SMI clkman regs ++- interrupts: *the* SMI interrupt. ++- pinctrl-names: should be "default". ++- pinctrl-0: the phandle of the gpio pin node. ++- brcm,smi-clock-source: the clock source for clkman ++- brcm,smi-clock-divisor: the integer clock divisor for clkman ++- dmas: the dma controller phandle and the DREQ number (4 on a 2835) ++- dma-names: the name used by the driver to request its channel. ++ Should be "rx-tx". ++ ++Optional properties: ++- None. ++ ++Examples: ++ ++8 data pin configuration: ++ ++smi: smi@7e600000 { ++ compatible = "brcm,bcm2835-smi"; ++ reg = <0x7e600000 0x44>, <0x7e1010b0 0x8>; ++ interrupts = <2 16>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&smi_pins>; ++ brcm,smi-clock-source = <6>; ++ brcm,smi-clock-divisor = <4>; ++ dmas = <&dma 4>; ++ dma-names = "rx-tx"; ++ ++ status = "okay"; ++}; ++ ++smi_pins: smi_pins { ++ brcm,pins = <2 3 4 5 6 7 8 9 10 11 12 13 14 15>; ++ /* Alt 1: SMI */ ++ brcm,function = <5 5 5 5 5 5 5 5 5 5 5 5 5 5>; ++ /* /CS, /WE and /OE are pulled high, as they are ++ generally active low signals */ ++ brcm,pull = <2 2 2 2 2 2 0 0 0 0 0 0 0 0>; ++}; ++ +--- a/drivers/char/broadcom/Kconfig ++++ b/drivers/char/broadcom/Kconfig +@@ -24,3 +24,12 @@ config BCM2835_DEVGPIOMEM + Provides users with root-free access to the GPIO registers + on the 2835. Calling mmap(/dev/gpiomem) will map the GPIO + register page to the user's pointer. ++ ++config BCM2835_SMI_DEV ++ tristate "Character device driver for BCM2835 Secondary Memory Interface" ++ depends on BCM2835_SMI ++ default m ++ help ++ This driver provides a character device interface (ioctl + read/write) to ++ Broadcom's Secondary Memory interface. The low-level functionality is provided ++ by the SMI driver itself. +--- a/drivers/char/broadcom/Makefile ++++ b/drivers/char/broadcom/Makefile +@@ -1,2 +1,3 @@ + obj-$(CONFIG_BCM2708_VCMEM) += vc_mem.o + obj-$(CONFIG_BCM2835_DEVGPIOMEM)+= bcm2835-gpiomem.o ++obj-$(CONFIG_BCM2835_SMI_DEV) += bcm2835_smi_dev.o +--- /dev/null ++++ b/drivers/char/broadcom/bcm2835_smi_dev.c +@@ -0,0 +1,402 @@ ++/** ++ * Character device driver for Broadcom Secondary Memory Interface ++ * ++ * Written by Luke Wren ++ * Copyright (c) 2015, Raspberry Pi (Trading) Ltd. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions ++ * are met: ++ * 1. Redistributions of source code must retain the above copyright ++ * notice, this list of conditions, and the following disclaimer, ++ * without modification. ++ * 2. Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in the ++ * documentation and/or other materials provided with the distribution. ++ * 3. The names of the above-listed copyright holders may not be used ++ * to endorse or promote products derived from this software without ++ * specific prior written permission. ++ * ++ * ALTERNATIVELY, this software may be distributed under the terms of the ++ * GNU General Public License ("GPL") version 2, as published by the Free ++ * Software Foundation. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS ++ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ++ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR ++ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR ++ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF ++ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING ++ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++ ++#define DEVICE_NAME "bcm2835-smi-dev" ++#define DRIVER_NAME "smi-dev-bcm2835" ++#define DEVICE_MINOR 0 ++ ++static struct cdev bcm2835_smi_cdev; ++static dev_t bcm2835_smi_devid; ++static struct class *bcm2835_smi_class; ++static struct device *bcm2835_smi_dev; ++ ++struct bcm2835_smi_dev_instance { ++ struct device *dev; ++}; ++ ++static struct bcm2835_smi_instance *smi_inst; ++static struct bcm2835_smi_dev_instance *inst; ++ ++static const char *const ioctl_names[] = { ++ "READ_SETTINGS", ++ "WRITE_SETTINGS", ++ "ADDRESS" ++}; ++ ++/**************************************************************************** ++* ++* SMI chardev file ops ++* ++***************************************************************************/ ++static long ++bcm2835_smi_ioctl(struct file *file, unsigned int cmd, unsigned long arg) ++{ ++ long ret = 0; ++ ++ dev_info(inst->dev, "serving ioctl..."); ++ ++ switch (cmd) { ++ case BCM2835_SMI_IOC_GET_SETTINGS:{ ++ struct smi_settings *settings; ++ ++ dev_info(inst->dev, "Reading SMI settings to user."); ++ settings = bcm2835_smi_get_settings_from_regs(smi_inst); ++ if (copy_to_user((void *)arg, settings, ++ sizeof(struct smi_settings))) ++ dev_err(inst->dev, "settings copy failed."); ++ break; ++ } ++ case BCM2835_SMI_IOC_WRITE_SETTINGS:{ ++ struct smi_settings *settings; ++ ++ dev_info(inst->dev, "Setting user's SMI settings."); ++ settings = bcm2835_smi_get_settings_from_regs(smi_inst); ++ if (copy_from_user(settings, (void *)arg, ++ sizeof(struct smi_settings))) ++ dev_err(inst->dev, "settings copy failed."); ++ else ++ bcm2835_smi_set_regs_from_settings(smi_inst); ++ break; ++ } ++ case BCM2835_SMI_IOC_ADDRESS: ++ dev_info(inst->dev, "SMI address set: 0x%02x", (int)arg); ++ bcm2835_smi_set_address(smi_inst, arg); ++ break; ++ default: ++ dev_err(inst->dev, "invalid ioctl cmd: %d", cmd); ++ ret = -ENOTTY; ++ break; ++ } ++ ++ return ret; ++} ++ ++static int bcm2835_smi_open(struct inode *inode, struct file *file) ++{ ++ int dev = iminor(inode); ++ ++ dev_dbg(inst->dev, "SMI device opened."); ++ ++ if (dev != DEVICE_MINOR) { ++ dev_err(inst->dev, ++ "bcm2835_smi_release: Unknown minor device: %d", ++ dev); ++ return -ENXIO; ++ } ++ ++ return 0; ++} ++ ++static int bcm2835_smi_release(struct inode *inode, struct file *file) ++{ ++ int dev = iminor(inode); ++ ++ if (dev != DEVICE_MINOR) { ++ dev_err(inst->dev, ++ "bcm2835_smi_release: Unknown minor device %d", dev); ++ return -ENXIO; ++ } ++ ++ return 0; ++} ++ ++static ssize_t dma_bounce_user( ++ enum dma_transfer_direction dma_dir, ++ char __user *user_ptr, ++ size_t count, ++ struct bcm2835_smi_bounce_info *bounce) ++{ ++ int chunk_size; ++ int chunk_no = 0; ++ int count_left = count; ++ ++ while (count_left) { ++ int rv; ++ void *buf; ++ ++ /* Wait for current chunk to complete: */ ++ if (down_timeout(&bounce->callback_sem, ++ msecs_to_jiffies(1000))) { ++ dev_err(inst->dev, "DMA bounce timed out"); ++ count -= (count_left); ++ break; ++ } ++ ++ if (bounce->callback_sem.count >= DMA_BOUNCE_BUFFER_COUNT - 1) ++ dev_err(inst->dev, "WARNING: Ring buffer overflow"); ++ chunk_size = count_left > DMA_BOUNCE_BUFFER_SIZE ? ++ DMA_BOUNCE_BUFFER_SIZE : count_left; ++ buf = bounce->buffer[chunk_no % DMA_BOUNCE_BUFFER_COUNT]; ++ if (dma_dir == DMA_DEV_TO_MEM) ++ rv = copy_to_user(user_ptr, buf, chunk_size); ++ else ++ rv = copy_from_user(buf, user_ptr, chunk_size); ++ if (rv) ++ dev_err(inst->dev, "copy_*_user() failed!: %d", rv); ++ user_ptr += chunk_size; ++ count_left -= chunk_size; ++ chunk_no++; ++ } ++ return count; ++} ++ ++static ssize_t ++bcm2835_read_file(struct file *f, char __user *user_ptr, ++ size_t count, loff_t *offs) ++{ ++ int odd_bytes; ++ ++ dev_dbg(inst->dev, "User reading %zu bytes from SMI.", count); ++ /* We don't want to DMA a number of bytes % 4 != 0 (32 bit FIFO) */ ++ if (count > DMA_THRESHOLD_BYTES) ++ odd_bytes = count & 0x3; ++ else ++ odd_bytes = count; ++ count -= odd_bytes; ++ if (count) { ++ struct bcm2835_smi_bounce_info *bounce; ++ ++ count = bcm2835_smi_user_dma(smi_inst, ++ DMA_DEV_TO_MEM, user_ptr, count, ++ &bounce); ++ if (count) ++ count = dma_bounce_user(DMA_DEV_TO_MEM, user_ptr, ++ count, bounce); ++ } ++ if (odd_bytes) { ++ /* Read from FIFO directly if not using DMA */ ++ uint8_t buf[DMA_THRESHOLD_BYTES]; ++ ++ bcm2835_smi_read_buf(smi_inst, buf, odd_bytes); ++ if (copy_to_user(user_ptr, buf, odd_bytes)) ++ dev_err(inst->dev, "copy_to_user() failed."); ++ count += odd_bytes; ++ ++ } ++ return count; ++} ++ ++static ssize_t ++bcm2835_write_file(struct file *f, const char __user *user_ptr, ++ size_t count, loff_t *offs) ++{ ++ int odd_bytes; ++ ++ dev_dbg(inst->dev, "User writing %zu bytes to SMI.", count); ++ if (count > DMA_THRESHOLD_BYTES) ++ odd_bytes = count & 0x3; ++ else ++ odd_bytes = count; ++ count -= odd_bytes; ++ if (count) { ++ struct bcm2835_smi_bounce_info *bounce; ++ ++ count = bcm2835_smi_user_dma(smi_inst, ++ DMA_MEM_TO_DEV, (char __user *)user_ptr, count, ++ &bounce); ++ if (count) ++ count = dma_bounce_user(DMA_MEM_TO_DEV, ++ (char __user *)user_ptr, ++ count, bounce); ++ } ++ if (odd_bytes) { ++ uint8_t buf[DMA_THRESHOLD_BYTES]; ++ ++ if (copy_from_user(buf, user_ptr, odd_bytes)) ++ dev_err(inst->dev, "copy_from_user() failed."); ++ else ++ bcm2835_smi_write_buf(smi_inst, buf, odd_bytes); ++ count += odd_bytes; ++ } ++ return count; ++} ++ ++static const struct file_operations ++bcm2835_smi_fops = { ++ .owner = THIS_MODULE, ++ .unlocked_ioctl = bcm2835_smi_ioctl, ++ .open = bcm2835_smi_open, ++ .release = bcm2835_smi_release, ++ .read = bcm2835_read_file, ++ .write = bcm2835_write_file, ++}; ++ ++ ++/**************************************************************************** ++* ++* bcm2835_smi_probe - called when the driver is loaded. ++* ++***************************************************************************/ ++ ++static int bcm2835_smi_dev_probe(struct platform_device *pdev) ++{ ++ int err; ++ void *ptr_err; ++ struct device *dev = &pdev->dev; ++ struct device_node *node = dev->of_node, *smi_node; ++ ++ if (!node) { ++ dev_err(dev, "No device tree node supplied!"); ++ return -EINVAL; ++ } ++ ++ smi_node = of_parse_phandle(node, "smi_handle", 0); ++ ++ if (!smi_node) { ++ dev_err(dev, "No such property: smi_handle"); ++ return -ENXIO; ++ } ++ ++ smi_inst = bcm2835_smi_get(smi_node); ++ ++ if (!smi_inst) ++ return -EPROBE_DEFER; ++ ++ /* Allocate buffers and instance data */ ++ ++ inst = devm_kzalloc(dev, sizeof(*inst), GFP_KERNEL); ++ ++ if (!inst) ++ return -ENOMEM; ++ ++ inst->dev = dev; ++ ++ /* Create character device entries */ ++ ++ err = alloc_chrdev_region(&bcm2835_smi_devid, ++ DEVICE_MINOR, 1, DEVICE_NAME); ++ if (err != 0) { ++ dev_err(inst->dev, "unable to allocate device number"); ++ return -ENOMEM; ++ } ++ cdev_init(&bcm2835_smi_cdev, &bcm2835_smi_fops); ++ bcm2835_smi_cdev.owner = THIS_MODULE; ++ err = cdev_add(&bcm2835_smi_cdev, bcm2835_smi_devid, 1); ++ if (err != 0) { ++ dev_err(inst->dev, "unable to register device"); ++ err = -ENOMEM; ++ goto failed_cdev_add; ++ } ++ ++ /* Create sysfs entries */ ++ ++ bcm2835_smi_class = class_create(THIS_MODULE, DEVICE_NAME); ++ ptr_err = bcm2835_smi_class; ++ if (IS_ERR(ptr_err)) ++ goto failed_class_create; ++ ++ bcm2835_smi_dev = device_create(bcm2835_smi_class, NULL, ++ bcm2835_smi_devid, NULL, ++ "smi"); ++ ptr_err = bcm2835_smi_dev; ++ if (IS_ERR(ptr_err)) ++ goto failed_device_create; ++ ++ dev_info(inst->dev, "initialised"); ++ ++ return 0; ++ ++failed_device_create: ++ class_destroy(bcm2835_smi_class); ++failed_class_create: ++ cdev_del(&bcm2835_smi_cdev); ++ err = PTR_ERR(ptr_err); ++failed_cdev_add: ++ unregister_chrdev_region(bcm2835_smi_devid, 1); ++ dev_err(dev, "could not load bcm2835_smi_dev"); ++ return err; ++} ++ ++/**************************************************************************** ++* ++* bcm2835_smi_remove - called when the driver is unloaded. ++* ++***************************************************************************/ ++ ++static int bcm2835_smi_dev_remove(struct platform_device *pdev) ++{ ++ device_destroy(bcm2835_smi_class, bcm2835_smi_devid); ++ class_destroy(bcm2835_smi_class); ++ cdev_del(&bcm2835_smi_cdev); ++ unregister_chrdev_region(bcm2835_smi_devid, 1); ++ ++ dev_info(inst->dev, "SMI character dev removed - OK"); ++ return 0; ++} ++ ++/**************************************************************************** ++* ++* Register the driver with device tree ++* ++***************************************************************************/ ++ ++static const struct of_device_id bcm2835_smi_dev_of_match[] = { ++ {.compatible = "brcm,bcm2835-smi-dev",}, ++ { /* sentinel */ }, ++}; ++ ++MODULE_DEVICE_TABLE(of, bcm2835_smi_dev_of_match); ++ ++static struct platform_driver bcm2835_smi_dev_driver = { ++ .probe = bcm2835_smi_dev_probe, ++ .remove = bcm2835_smi_dev_remove, ++ .driver = { ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ .of_match_table = bcm2835_smi_dev_of_match, ++ }, ++}; ++ ++module_platform_driver(bcm2835_smi_dev_driver); ++ ++MODULE_ALIAS("platform:smi-dev-bcm2835"); ++MODULE_LICENSE("GPL"); ++MODULE_DESCRIPTION( ++ "Character device driver for BCM2835's secondary memory interface"); ++MODULE_AUTHOR("Luke Wren "); +--- a/drivers/misc/Kconfig ++++ b/drivers/misc/Kconfig +@@ -9,6 +9,14 @@ config SENSORS_LIS3LV02D + tristate + depends on INPUT + ++config BCM2835_SMI ++ tristate "Broadcom 283x Secondary Memory Interface driver" ++ depends on ARCH_BCM2835 ++ default m ++ help ++ Driver for enabling and using Broadcom's Secondary/Slow Memory Interface. ++ Appears as /dev/bcm2835_smi. For ioctl interface see drivers/misc/bcm2835_smi.h ++ + config AD525X_DPOT + tristate "Analog Devices Digital Potentiometers" + depends on (I2C || SPI) && SYSFS +--- a/drivers/misc/Makefile ++++ b/drivers/misc/Makefile +@@ -11,6 +11,7 @@ obj-$(CONFIG_AD525X_DPOT_SPI) += ad525x_ + obj-$(CONFIG_INTEL_MID_PTI) += pti.o + obj-$(CONFIG_ATMEL_SSC) += atmel-ssc.o + obj-$(CONFIG_ATMEL_TCLIB) += atmel_tclib.o ++obj-$(CONFIG_BCM2835_SMI) += bcm2835_smi.o + obj-$(CONFIG_DUMMY_IRQ) += dummy-irq.o + obj-$(CONFIG_ICS932S401) += ics932s401.o + obj-$(CONFIG_LKDTM) += lkdtm/ +--- /dev/null ++++ b/drivers/misc/bcm2835_smi.c +@@ -0,0 +1,955 @@ ++/** ++ * Broadcom Secondary Memory Interface driver ++ * ++ * Written by Luke Wren ++ * Copyright (c) 2015, Raspberry Pi (Trading) Ltd. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions ++ * are met: ++ * 1. Redistributions of source code must retain the above copyright ++ * notice, this list of conditions, and the following disclaimer, ++ * without modification. ++ * 2. Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in the ++ * documentation and/or other materials provided with the distribution. ++ * 3. The names of the above-listed copyright holders may not be used ++ * to endorse or promote products derived from this software without ++ * specific prior written permission. ++ * ++ * ALTERNATIVELY, this software may be distributed under the terms of the ++ * GNU General Public License ("GPL") version 2, as published by the Free ++ * Software Foundation. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS ++ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ++ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR ++ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR ++ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF ++ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING ++ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define BCM2835_SMI_IMPLEMENTATION ++#include ++ ++#define DRIVER_NAME "smi-bcm2835" ++ ++#define N_PAGES_FROM_BYTES(n) ((n + PAGE_SIZE-1) / PAGE_SIZE) ++ ++#define DMA_WRITE_TO_MEM true ++#define DMA_READ_FROM_MEM false ++ ++struct bcm2835_smi_instance { ++ struct device *dev; ++ struct smi_settings settings; ++ __iomem void *smi_regs_ptr; ++ dma_addr_t smi_regs_busaddr; ++ ++ struct dma_chan *dma_chan; ++ struct dma_slave_config dma_config; ++ ++ struct bcm2835_smi_bounce_info bounce; ++ ++ struct scatterlist buffer_sgl; ++ ++ struct clk *clk; ++ ++ /* Sometimes we are called into in an atomic context (e.g. by ++ JFFS2 + MTD) so we can't use a mutex */ ++ spinlock_t transaction_lock; ++}; ++ ++/**************************************************************************** ++* ++* SMI peripheral setup ++* ++***************************************************************************/ ++ ++static inline void write_smi_reg(struct bcm2835_smi_instance *inst, ++ u32 val, unsigned reg) ++{ ++ writel(val, inst->smi_regs_ptr + reg); ++} ++ ++static inline u32 read_smi_reg(struct bcm2835_smi_instance *inst, unsigned reg) ++{ ++ return readl(inst->smi_regs_ptr + reg); ++} ++ ++/* Token-paste macro for e.g SMIDSR_RSTROBE -> value of SMIDSR_RSTROBE_MASK */ ++#define _CONCAT(x, y) x##y ++#define CONCAT(x, y) _CONCAT(x, y) ++ ++#define SET_BIT_FIELD(dest, field, bits) ((dest) = \ ++ ((dest) & ~CONCAT(field, _MASK)) | (((bits) << CONCAT(field, _OFFS))& \ ++ CONCAT(field, _MASK))) ++#define GET_BIT_FIELD(src, field) (((src) & \ ++ CONCAT(field, _MASK)) >> CONCAT(field, _OFFS)) ++ ++static void smi_dump_context_labelled(struct bcm2835_smi_instance *inst, ++ const char *label) ++{ ++ dev_err(inst->dev, "SMI context dump: %s", label); ++ dev_err(inst->dev, "SMICS: 0x%08x", read_smi_reg(inst, SMICS)); ++ dev_err(inst->dev, "SMIL: 0x%08x", read_smi_reg(inst, SMIL)); ++ dev_err(inst->dev, "SMIDSR: 0x%08x", read_smi_reg(inst, SMIDSR0)); ++ dev_err(inst->dev, "SMIDSW: 0x%08x", read_smi_reg(inst, SMIDSW0)); ++ dev_err(inst->dev, "SMIDC: 0x%08x", read_smi_reg(inst, SMIDC)); ++ dev_err(inst->dev, "SMIFD: 0x%08x", read_smi_reg(inst, SMIFD)); ++ dev_err(inst->dev, " "); ++} ++ ++static inline void smi_dump_context(struct bcm2835_smi_instance *inst) ++{ ++ smi_dump_context_labelled(inst, ""); ++} ++ ++static void smi_get_default_settings(struct bcm2835_smi_instance *inst) ++{ ++ struct smi_settings *settings = &inst->settings; ++ ++ settings->data_width = SMI_WIDTH_16BIT; ++ settings->pack_data = true; ++ ++ settings->read_setup_time = 1; ++ settings->read_hold_time = 1; ++ settings->read_pace_time = 1; ++ settings->read_strobe_time = 3; ++ ++ settings->write_setup_time = settings->read_setup_time; ++ settings->write_hold_time = settings->read_hold_time; ++ settings->write_pace_time = settings->read_pace_time; ++ settings->write_strobe_time = settings->read_strobe_time; ++ ++ settings->dma_enable = true; ++ settings->dma_passthrough_enable = false; ++ settings->dma_read_thresh = 0x01; ++ settings->dma_write_thresh = 0x3f; ++ settings->dma_panic_read_thresh = 0x20; ++ settings->dma_panic_write_thresh = 0x20; ++} ++ ++void bcm2835_smi_set_regs_from_settings(struct bcm2835_smi_instance *inst) ++{ ++ struct smi_settings *settings = &inst->settings; ++ int smidsr_temp = 0, smidsw_temp = 0, smics_temp, ++ smidcs_temp, smidc_temp = 0; ++ ++ spin_lock(&inst->transaction_lock); ++ ++ /* temporarily disable the peripheral: */ ++ smics_temp = read_smi_reg(inst, SMICS); ++ write_smi_reg(inst, 0, SMICS); ++ smidcs_temp = read_smi_reg(inst, SMIDCS); ++ write_smi_reg(inst, 0, SMIDCS); ++ ++ if (settings->pack_data) ++ smics_temp |= SMICS_PXLDAT; ++ else ++ smics_temp &= ~SMICS_PXLDAT; ++ ++ SET_BIT_FIELD(smidsr_temp, SMIDSR_RWIDTH, settings->data_width); ++ SET_BIT_FIELD(smidsr_temp, SMIDSR_RSETUP, settings->read_setup_time); ++ SET_BIT_FIELD(smidsr_temp, SMIDSR_RHOLD, settings->read_hold_time); ++ SET_BIT_FIELD(smidsr_temp, SMIDSR_RPACE, settings->read_pace_time); ++ SET_BIT_FIELD(smidsr_temp, SMIDSR_RSTROBE, settings->read_strobe_time); ++ write_smi_reg(inst, smidsr_temp, SMIDSR0); ++ ++ SET_BIT_FIELD(smidsw_temp, SMIDSW_WWIDTH, settings->data_width); ++ if (settings->data_width == SMI_WIDTH_8BIT) ++ smidsw_temp |= SMIDSW_WSWAP; ++ else ++ smidsw_temp &= ~SMIDSW_WSWAP; ++ SET_BIT_FIELD(smidsw_temp, SMIDSW_WSETUP, settings->write_setup_time); ++ SET_BIT_FIELD(smidsw_temp, SMIDSW_WHOLD, settings->write_hold_time); ++ SET_BIT_FIELD(smidsw_temp, SMIDSW_WPACE, settings->write_pace_time); ++ SET_BIT_FIELD(smidsw_temp, SMIDSW_WSTROBE, ++ settings->write_strobe_time); ++ write_smi_reg(inst, smidsw_temp, SMIDSW0); ++ ++ SET_BIT_FIELD(smidc_temp, SMIDC_REQR, settings->dma_read_thresh); ++ SET_BIT_FIELD(smidc_temp, SMIDC_REQW, settings->dma_write_thresh); ++ SET_BIT_FIELD(smidc_temp, SMIDC_PANICR, ++ settings->dma_panic_read_thresh); ++ SET_BIT_FIELD(smidc_temp, SMIDC_PANICW, ++ settings->dma_panic_write_thresh); ++ if (settings->dma_passthrough_enable) { ++ smidc_temp |= SMIDC_DMAP; ++ smidsr_temp |= SMIDSR_RDREQ; ++ write_smi_reg(inst, smidsr_temp, SMIDSR0); ++ smidsw_temp |= SMIDSW_WDREQ; ++ write_smi_reg(inst, smidsw_temp, SMIDSW0); ++ } else ++ smidc_temp &= ~SMIDC_DMAP; ++ if (settings->dma_enable) ++ smidc_temp |= SMIDC_DMAEN; ++ else ++ smidc_temp &= ~SMIDC_DMAEN; ++ ++ write_smi_reg(inst, smidc_temp, SMIDC); ++ ++ /* re-enable (if was previously enabled) */ ++ write_smi_reg(inst, smics_temp, SMICS); ++ write_smi_reg(inst, smidcs_temp, SMIDCS); ++ ++ spin_unlock(&inst->transaction_lock); ++} ++EXPORT_SYMBOL(bcm2835_smi_set_regs_from_settings); ++ ++struct smi_settings *bcm2835_smi_get_settings_from_regs ++ (struct bcm2835_smi_instance *inst) ++{ ++ struct smi_settings *settings = &inst->settings; ++ int smidsr, smidsw, smidc; ++ ++ spin_lock(&inst->transaction_lock); ++ ++ smidsr = read_smi_reg(inst, SMIDSR0); ++ smidsw = read_smi_reg(inst, SMIDSW0); ++ smidc = read_smi_reg(inst, SMIDC); ++ ++ settings->pack_data = (read_smi_reg(inst, SMICS) & SMICS_PXLDAT) ? ++ true : false; ++ ++ settings->data_width = GET_BIT_FIELD(smidsr, SMIDSR_RWIDTH); ++ settings->read_setup_time = GET_BIT_FIELD(smidsr, SMIDSR_RSETUP); ++ settings->read_hold_time = GET_BIT_FIELD(smidsr, SMIDSR_RHOLD); ++ settings->read_pace_time = GET_BIT_FIELD(smidsr, SMIDSR_RPACE); ++ settings->read_strobe_time = GET_BIT_FIELD(smidsr, SMIDSR_RSTROBE); ++ ++ settings->write_setup_time = GET_BIT_FIELD(smidsw, SMIDSW_WSETUP); ++ settings->write_hold_time = GET_BIT_FIELD(smidsw, SMIDSW_WHOLD); ++ settings->write_pace_time = GET_BIT_FIELD(smidsw, SMIDSW_WPACE); ++ settings->write_strobe_time = GET_BIT_FIELD(smidsw, SMIDSW_WSTROBE); ++ ++ settings->dma_read_thresh = GET_BIT_FIELD(smidc, SMIDC_REQR); ++ settings->dma_write_thresh = GET_BIT_FIELD(smidc, SMIDC_REQW); ++ settings->dma_panic_read_thresh = GET_BIT_FIELD(smidc, SMIDC_PANICR); ++ settings->dma_panic_write_thresh = GET_BIT_FIELD(smidc, SMIDC_PANICW); ++ settings->dma_passthrough_enable = (smidc & SMIDC_DMAP) ? true : false; ++ settings->dma_enable = (smidc & SMIDC_DMAEN) ? true : false; ++ ++ spin_unlock(&inst->transaction_lock); ++ ++ return settings; ++} ++EXPORT_SYMBOL(bcm2835_smi_get_settings_from_regs); ++ ++static inline void smi_set_address(struct bcm2835_smi_instance *inst, ++ unsigned int address) ++{ ++ int smia_temp = 0, smida_temp = 0; ++ ++ SET_BIT_FIELD(smia_temp, SMIA_ADDR, address); ++ SET_BIT_FIELD(smida_temp, SMIDA_ADDR, address); ++ ++ /* Write to both address registers - user doesn't care whether we're ++ doing programmed or direct transfers. */ ++ write_smi_reg(inst, smia_temp, SMIA); ++ write_smi_reg(inst, smida_temp, SMIDA); ++} ++ ++static void smi_setup_regs(struct bcm2835_smi_instance *inst) ++{ ++ ++ dev_dbg(inst->dev, "Initialising SMI registers..."); ++ /* Disable the peripheral if already enabled */ ++ write_smi_reg(inst, 0, SMICS); ++ write_smi_reg(inst, 0, SMIDCS); ++ ++ smi_get_default_settings(inst); ++ bcm2835_smi_set_regs_from_settings(inst); ++ smi_set_address(inst, 0); ++ ++ write_smi_reg(inst, read_smi_reg(inst, SMICS) | SMICS_ENABLE, SMICS); ++ write_smi_reg(inst, read_smi_reg(inst, SMIDCS) | SMIDCS_ENABLE, ++ SMIDCS); ++} ++ ++/**************************************************************************** ++* ++* Low-level SMI access functions ++* Other modules should use the exported higher-level functions e.g. ++* bcm2835_smi_write_buf() unless they have a good reason to use these ++* ++***************************************************************************/ ++ ++static inline uint32_t smi_read_single_word(struct bcm2835_smi_instance *inst) ++{ ++ int timeout = 0; ++ ++ write_smi_reg(inst, SMIDCS_ENABLE, SMIDCS); ++ write_smi_reg(inst, SMIDCS_ENABLE | SMIDCS_START, SMIDCS); ++ /* Make sure things happen in the right order...*/ ++ mb(); ++ while (!(read_smi_reg(inst, SMIDCS) & SMIDCS_DONE) && ++ ++timeout < 10000) ++ ; ++ if (timeout < 10000) ++ return read_smi_reg(inst, SMIDD); ++ ++ dev_err(inst->dev, ++ "SMI direct read timed out (is the clock set up correctly?)"); ++ return 0; ++} ++ ++static inline void smi_write_single_word(struct bcm2835_smi_instance *inst, ++ uint32_t data) ++{ ++ int timeout = 0; ++ ++ write_smi_reg(inst, SMIDCS_ENABLE | SMIDCS_WRITE, SMIDCS); ++ write_smi_reg(inst, data, SMIDD); ++ write_smi_reg(inst, SMIDCS_ENABLE | SMIDCS_WRITE | SMIDCS_START, ++ SMIDCS); ++ ++ while (!(read_smi_reg(inst, SMIDCS) & SMIDCS_DONE) && ++ ++timeout < 10000) ++ ; ++ if (timeout >= 10000) ++ dev_err(inst->dev, ++ "SMI direct write timed out (is the clock set up correctly?)"); ++} ++ ++/* Initiates a programmed read into the read FIFO. It is up to the caller to ++ * read data from the FIFO - either via paced DMA transfer, ++ * or polling SMICS_RXD to check whether data is available. ++ * SMICS_ACTIVE will go low upon completion. */ ++static void smi_init_programmed_read(struct bcm2835_smi_instance *inst, ++ int num_transfers) ++{ ++ int smics_temp; ++ ++ /* Disable the peripheral: */ ++ smics_temp = read_smi_reg(inst, SMICS) & ~(SMICS_ENABLE | SMICS_WRITE); ++ write_smi_reg(inst, smics_temp, SMICS); ++ while (read_smi_reg(inst, SMICS) & SMICS_ENABLE) ++ ; ++ ++ /* Program the transfer count: */ ++ write_smi_reg(inst, num_transfers, SMIL); ++ ++ /* re-enable and start: */ ++ smics_temp |= SMICS_ENABLE; ++ write_smi_reg(inst, smics_temp, SMICS); ++ smics_temp |= SMICS_CLEAR; ++ /* Just to be certain: */ ++ mb(); ++ while (read_smi_reg(inst, SMICS) & SMICS_ACTIVE) ++ ; ++ write_smi_reg(inst, smics_temp, SMICS); ++ smics_temp |= SMICS_START; ++ write_smi_reg(inst, smics_temp, SMICS); ++} ++ ++/* Initiates a programmed write sequence, using data from the write FIFO. ++ * It is up to the caller to initiate a DMA transfer before calling, ++ * or use another method to keep the write FIFO topped up. ++ * SMICS_ACTIVE will go low upon completion. ++ */ ++static void smi_init_programmed_write(struct bcm2835_smi_instance *inst, ++ int num_transfers) ++{ ++ int smics_temp; ++ ++ /* Disable the peripheral: */ ++ smics_temp = read_smi_reg(inst, SMICS) & ~SMICS_ENABLE; ++ write_smi_reg(inst, smics_temp, SMICS); ++ while (read_smi_reg(inst, SMICS) & SMICS_ENABLE) ++ ; ++ ++ /* Program the transfer count: */ ++ write_smi_reg(inst, num_transfers, SMIL); ++ ++ /* setup, re-enable and start: */ ++ smics_temp |= SMICS_WRITE | SMICS_ENABLE; ++ write_smi_reg(inst, smics_temp, SMICS); ++ smics_temp |= SMICS_START; ++ write_smi_reg(inst, smics_temp, SMICS); ++} ++ ++/* Initiate a read and then poll FIFO for data, reading out as it appears. */ ++static void smi_read_fifo(struct bcm2835_smi_instance *inst, ++ uint32_t *dest, int n_bytes) ++{ ++ if (read_smi_reg(inst, SMICS) & SMICS_RXD) { ++ smi_dump_context_labelled(inst, ++ "WARNING: read FIFO not empty at start of read call."); ++ while (read_smi_reg(inst, SMICS)) ++ ; ++ } ++ ++ /* Dispatch the read: */ ++ if (inst->settings.data_width == SMI_WIDTH_8BIT) ++ smi_init_programmed_read(inst, n_bytes); ++ else if (inst->settings.data_width == SMI_WIDTH_16BIT) ++ smi_init_programmed_read(inst, n_bytes / 2); ++ else { ++ dev_err(inst->dev, "Unsupported data width for read."); ++ return; ++ } ++ ++ /* Poll FIFO to keep it empty */ ++ while (!(read_smi_reg(inst, SMICS) & SMICS_DONE)) ++ if (read_smi_reg(inst, SMICS) & SMICS_RXD) ++ *dest++ = read_smi_reg(inst, SMID); ++ ++ /* Ensure that the FIFO is emptied */ ++ if (read_smi_reg(inst, SMICS) & SMICS_RXD) { ++ int fifo_count; ++ ++ fifo_count = GET_BIT_FIELD(read_smi_reg(inst, SMIFD), ++ SMIFD_FCNT); ++ while (fifo_count--) ++ *dest++ = read_smi_reg(inst, SMID); ++ } ++ ++ if (!(read_smi_reg(inst, SMICS) & SMICS_DONE)) ++ smi_dump_context_labelled(inst, ++ "WARNING: transaction finished but done bit not set."); ++ ++ if (read_smi_reg(inst, SMICS) & SMICS_RXD) ++ smi_dump_context_labelled(inst, ++ "WARNING: read FIFO not empty at end of read call."); ++ ++} ++ ++/* Initiate a write, and then keep the FIFO topped up. */ ++static void smi_write_fifo(struct bcm2835_smi_instance *inst, ++ uint32_t *src, int n_bytes) ++{ ++ int i, timeout = 0; ++ ++ /* Empty FIFOs if not already so */ ++ if (!(read_smi_reg(inst, SMICS) & SMICS_TXE)) { ++ smi_dump_context_labelled(inst, ++ "WARNING: write fifo not empty at start of write call."); ++ write_smi_reg(inst, read_smi_reg(inst, SMICS) | SMICS_CLEAR, ++ SMICS); ++ } ++ ++ /* Initiate the transfer */ ++ if (inst->settings.data_width == SMI_WIDTH_8BIT) ++ smi_init_programmed_write(inst, n_bytes); ++ else if (inst->settings.data_width == SMI_WIDTH_16BIT) ++ smi_init_programmed_write(inst, n_bytes / 2); ++ else { ++ dev_err(inst->dev, "Unsupported data width for write."); ++ return; ++ } ++ /* Fill the FIFO: */ ++ for (i = 0; i < (n_bytes - 1) / 4 + 1; ++i) { ++ while (!(read_smi_reg(inst, SMICS) & SMICS_TXD)) ++ ; ++ write_smi_reg(inst, *src++, SMID); ++ } ++ /* Busy wait... */ ++ while (!(read_smi_reg(inst, SMICS) & SMICS_DONE) && ++timeout < ++ 1000000) ++ ; ++ if (timeout >= 1000000) ++ smi_dump_context_labelled(inst, ++ "Timed out on write operation!"); ++ if (!(read_smi_reg(inst, SMICS) & SMICS_TXE)) ++ smi_dump_context_labelled(inst, ++ "WARNING: FIFO not empty at end of write operation."); ++} ++ ++/**************************************************************************** ++* ++* SMI DMA operations ++* ++***************************************************************************/ ++ ++/* Disable SMI and put it into the correct direction before doing DMA setup. ++ Stops spurious DREQs during setup. Peripheral is re-enabled by init_*() */ ++static void smi_disable(struct bcm2835_smi_instance *inst, ++ enum dma_transfer_direction direction) ++{ ++ int smics_temp = read_smi_reg(inst, SMICS) & ~SMICS_ENABLE; ++ ++ if (direction == DMA_DEV_TO_MEM) ++ smics_temp &= ~SMICS_WRITE; ++ else ++ smics_temp |= SMICS_WRITE; ++ write_smi_reg(inst, smics_temp, SMICS); ++ while (read_smi_reg(inst, SMICS) & SMICS_ACTIVE) ++ ; ++} ++ ++static struct scatterlist *smi_scatterlist_from_buffer( ++ struct bcm2835_smi_instance *inst, ++ dma_addr_t buf, ++ size_t len, ++ struct scatterlist *sg) ++{ ++ sg_init_table(sg, 1); ++ sg_dma_address(sg) = buf; ++ sg_dma_len(sg) = len; ++ return sg; ++} ++ ++static void smi_dma_callback_user_copy(void *param) ++{ ++ /* Notify the bottom half that a chunk is ready for user copy */ ++ struct bcm2835_smi_instance *inst = ++ (struct bcm2835_smi_instance *)param; ++ ++ up(&inst->bounce.callback_sem); ++} ++ ++/* Creates a descriptor, assigns the given callback, and submits the ++ descriptor to dmaengine. Does not block - can queue up multiple ++ descriptors and then wait for them all to complete. ++ sg_len is the number of control blocks, NOT the number of bytes. ++ dir can be DMA_MEM_TO_DEV or DMA_DEV_TO_MEM. ++ callback can be NULL - in this case it is not called. */ ++static inline struct dma_async_tx_descriptor *smi_dma_submit_sgl( ++ struct bcm2835_smi_instance *inst, ++ struct scatterlist *sgl, ++ size_t sg_len, ++ enum dma_transfer_direction dir, ++ dma_async_tx_callback callback) ++{ ++ struct dma_async_tx_descriptor *desc; ++ ++ desc = dmaengine_prep_slave_sg(inst->dma_chan, ++ sgl, ++ sg_len, ++ dir, ++ DMA_PREP_INTERRUPT | DMA_CTRL_ACK | ++ DMA_PREP_FENCE); ++ if (!desc) { ++ dev_err(inst->dev, "read_sgl: dma slave preparation failed!"); ++ write_smi_reg(inst, read_smi_reg(inst, SMICS) & ~SMICS_ACTIVE, ++ SMICS); ++ while (read_smi_reg(inst, SMICS) & SMICS_ACTIVE) ++ cpu_relax(); ++ write_smi_reg(inst, read_smi_reg(inst, SMICS) | SMICS_ACTIVE, ++ SMICS); ++ return NULL; ++ } ++ desc->callback = callback; ++ desc->callback_param = inst; ++ if (dmaengine_submit(desc) < 0) ++ return NULL; ++ return desc; ++} ++ ++/* NB this function blocks until the transfer is complete */ ++static void ++smi_dma_read_sgl(struct bcm2835_smi_instance *inst, ++ struct scatterlist *sgl, size_t sg_len, size_t n_bytes) ++{ ++ struct dma_async_tx_descriptor *desc; ++ ++ /* Disable SMI and set to read before dispatching DMA - if SMI is in ++ * write mode and TX fifo is empty, it will generate a DREQ which may ++ * cause the read DMA to complete before the SMI read command is even ++ * dispatched! We want to dispatch DMA before SMI read so that reading ++ * is gapless, for logic analyser. ++ */ ++ ++ smi_disable(inst, DMA_DEV_TO_MEM); ++ ++ desc = smi_dma_submit_sgl(inst, sgl, sg_len, DMA_DEV_TO_MEM, NULL); ++ dma_async_issue_pending(inst->dma_chan); ++ ++ if (inst->settings.data_width == SMI_WIDTH_8BIT) ++ smi_init_programmed_read(inst, n_bytes); ++ else ++ smi_init_programmed_read(inst, n_bytes / 2); ++ ++ if (dma_wait_for_async_tx(desc) == DMA_ERROR) ++ smi_dump_context_labelled(inst, "DMA timeout!"); ++} ++ ++static void ++smi_dma_write_sgl(struct bcm2835_smi_instance *inst, ++ struct scatterlist *sgl, size_t sg_len, size_t n_bytes) ++{ ++ struct dma_async_tx_descriptor *desc; ++ ++ if (inst->settings.data_width == SMI_WIDTH_8BIT) ++ smi_init_programmed_write(inst, n_bytes); ++ else ++ smi_init_programmed_write(inst, n_bytes / 2); ++ ++ desc = smi_dma_submit_sgl(inst, sgl, sg_len, DMA_MEM_TO_DEV, NULL); ++ dma_async_issue_pending(inst->dma_chan); ++ ++ if (dma_wait_for_async_tx(desc) == DMA_ERROR) ++ smi_dump_context_labelled(inst, "DMA timeout!"); ++ else ++ /* Wait for SMI to finish our writes */ ++ while (!(read_smi_reg(inst, SMICS) & SMICS_DONE)) ++ cpu_relax(); ++} ++ ++ssize_t bcm2835_smi_user_dma( ++ struct bcm2835_smi_instance *inst, ++ enum dma_transfer_direction dma_dir, ++ char __user *user_ptr, size_t count, ++ struct bcm2835_smi_bounce_info **bounce) ++{ ++ int chunk_no = 0, chunk_size, count_left = count; ++ struct scatterlist *sgl; ++ void (*init_trans_func)(struct bcm2835_smi_instance *, int); ++ ++ spin_lock(&inst->transaction_lock); ++ ++ if (dma_dir == DMA_DEV_TO_MEM) ++ init_trans_func = smi_init_programmed_read; ++ else ++ init_trans_func = smi_init_programmed_write; ++ ++ smi_disable(inst, dma_dir); ++ ++ sema_init(&inst->bounce.callback_sem, 0); ++ if (bounce) ++ *bounce = &inst->bounce; ++ while (count_left) { ++ chunk_size = count_left > DMA_BOUNCE_BUFFER_SIZE ? ++ DMA_BOUNCE_BUFFER_SIZE : count_left; ++ if (chunk_size == DMA_BOUNCE_BUFFER_SIZE) { ++ sgl = ++ &inst->bounce.sgl[chunk_no % DMA_BOUNCE_BUFFER_COUNT]; ++ } else { ++ sgl = smi_scatterlist_from_buffer( ++ inst, ++ inst->bounce.phys[ ++ chunk_no % DMA_BOUNCE_BUFFER_COUNT], ++ chunk_size, ++ &inst->buffer_sgl); ++ } ++ ++ if (!smi_dma_submit_sgl(inst, sgl, 1, dma_dir, ++ smi_dma_callback_user_copy ++ )) { ++ dev_err(inst->dev, "sgl submit failed"); ++ count = 0; ++ goto out; ++ } ++ count_left -= chunk_size; ++ chunk_no++; ++ } ++ dma_async_issue_pending(inst->dma_chan); ++ ++ if (inst->settings.data_width == SMI_WIDTH_8BIT) ++ init_trans_func(inst, count); ++ else if (inst->settings.data_width == SMI_WIDTH_16BIT) ++ init_trans_func(inst, count / 2); ++out: ++ spin_unlock(&inst->transaction_lock); ++ return count; ++} ++EXPORT_SYMBOL(bcm2835_smi_user_dma); ++ ++ ++/**************************************************************************** ++* ++* High level buffer transfer functions - for use by other drivers ++* ++***************************************************************************/ ++ ++/* Buffer must be physically contiguous - i.e. kmalloc, not vmalloc! */ ++void bcm2835_smi_write_buf( ++ struct bcm2835_smi_instance *inst, ++ const void *buf, size_t n_bytes) ++{ ++ int odd_bytes = n_bytes & 0x3; ++ ++ n_bytes -= odd_bytes; ++ ++ spin_lock(&inst->transaction_lock); ++ ++ if (n_bytes > DMA_THRESHOLD_BYTES) { ++ dma_addr_t phy_addr = dma_map_single( ++ inst->dev, ++ (void *)buf, ++ n_bytes, ++ DMA_MEM_TO_DEV); ++ struct scatterlist *sgl = ++ smi_scatterlist_from_buffer(inst, phy_addr, n_bytes, ++ &inst->buffer_sgl); ++ ++ if (!sgl) { ++ smi_dump_context_labelled(inst, ++ "Error: could not create scatterlist for write!"); ++ goto out; ++ } ++ smi_dma_write_sgl(inst, sgl, 1, n_bytes); ++ ++ dma_unmap_single ++ (inst->dev, phy_addr, n_bytes, DMA_MEM_TO_DEV); ++ } else if (n_bytes) { ++ smi_write_fifo(inst, (uint32_t *) buf, n_bytes); ++ } ++ buf += n_bytes; ++ ++ if (inst->settings.data_width == SMI_WIDTH_8BIT) { ++ while (odd_bytes--) ++ smi_write_single_word(inst, *(uint8_t *) (buf++)); ++ } else { ++ while (odd_bytes >= 2) { ++ smi_write_single_word(inst, *(uint16_t *)buf); ++ buf += 2; ++ odd_bytes -= 2; ++ } ++ if (odd_bytes) { ++ /* Reading an odd number of bytes on a 16 bit bus is ++ a user bug. It's kinder to fail early and tell them ++ than to e.g. transparently give them the bottom byte ++ of a 16 bit transfer. */ ++ dev_err(inst->dev, ++ "WARNING: odd number of bytes specified for wide transfer."); ++ dev_err(inst->dev, ++ "At least one byte dropped as a result."); ++ dump_stack(); ++ } ++ } ++out: ++ spin_unlock(&inst->transaction_lock); ++} ++EXPORT_SYMBOL(bcm2835_smi_write_buf); ++ ++void bcm2835_smi_read_buf(struct bcm2835_smi_instance *inst, ++ void *buf, size_t n_bytes) ++{ ++ ++ /* SMI is inherently 32-bit, which causes surprising amounts of mess ++ for bytes % 4 != 0. Easiest to avoid this mess altogether ++ by handling remainder separately. */ ++ int odd_bytes = n_bytes & 0x3; ++ ++ spin_lock(&inst->transaction_lock); ++ n_bytes -= odd_bytes; ++ if (n_bytes > DMA_THRESHOLD_BYTES) { ++ dma_addr_t phy_addr = dma_map_single(inst->dev, ++ buf, n_bytes, ++ DMA_DEV_TO_MEM); ++ struct scatterlist *sgl = smi_scatterlist_from_buffer( ++ inst, phy_addr, n_bytes, ++ &inst->buffer_sgl); ++ if (!sgl) { ++ smi_dump_context_labelled(inst, ++ "Error: could not create scatterlist for read!"); ++ goto out; ++ } ++ smi_dma_read_sgl(inst, sgl, 1, n_bytes); ++ dma_unmap_single(inst->dev, phy_addr, n_bytes, DMA_DEV_TO_MEM); ++ } else if (n_bytes) { ++ smi_read_fifo(inst, (uint32_t *)buf, n_bytes); ++ } ++ buf += n_bytes; ++ ++ if (inst->settings.data_width == SMI_WIDTH_8BIT) { ++ while (odd_bytes--) ++ *((uint8_t *) (buf++)) = smi_read_single_word(inst); ++ } else { ++ while (odd_bytes >= 2) { ++ *(uint16_t *) buf = smi_read_single_word(inst); ++ buf += 2; ++ odd_bytes -= 2; ++ } ++ if (odd_bytes) { ++ dev_err(inst->dev, ++ "WARNING: odd number of bytes specified for wide transfer."); ++ dev_err(inst->dev, ++ "At least one byte dropped as a result."); ++ dump_stack(); ++ } ++ } ++out: ++ spin_unlock(&inst->transaction_lock); ++} ++EXPORT_SYMBOL(bcm2835_smi_read_buf); ++ ++void bcm2835_smi_set_address(struct bcm2835_smi_instance *inst, ++ unsigned int address) ++{ ++ spin_lock(&inst->transaction_lock); ++ smi_set_address(inst, address); ++ spin_unlock(&inst->transaction_lock); ++} ++EXPORT_SYMBOL(bcm2835_smi_set_address); ++ ++struct bcm2835_smi_instance *bcm2835_smi_get(struct device_node *node) ++{ ++ struct platform_device *pdev; ++ ++ if (!node) ++ return NULL; ++ ++ pdev = of_find_device_by_node(node); ++ if (!pdev) ++ return NULL; ++ ++ return platform_get_drvdata(pdev); ++} ++EXPORT_SYMBOL(bcm2835_smi_get); ++ ++/**************************************************************************** ++* ++* bcm2835_smi_probe - called when the driver is loaded. ++* ++***************************************************************************/ ++ ++static int bcm2835_smi_dma_setup(struct bcm2835_smi_instance *inst) ++{ ++ int i, rv = 0; ++ ++ inst->dma_chan = dma_request_slave_channel(inst->dev, "rx-tx"); ++ ++ inst->dma_config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; ++ inst->dma_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; ++ inst->dma_config.src_addr = inst->smi_regs_busaddr + SMID; ++ inst->dma_config.dst_addr = inst->dma_config.src_addr; ++ /* Direction unimportant - always overridden by prep_slave_sg */ ++ inst->dma_config.direction = DMA_DEV_TO_MEM; ++ dmaengine_slave_config(inst->dma_chan, &inst->dma_config); ++ /* Alloc and map bounce buffers */ ++ for (i = 0; i < DMA_BOUNCE_BUFFER_COUNT; ++i) { ++ inst->bounce.buffer[i] = ++ dmam_alloc_coherent(inst->dev, DMA_BOUNCE_BUFFER_SIZE, ++ &inst->bounce.phys[i], ++ GFP_KERNEL); ++ if (!inst->bounce.buffer[i]) { ++ dev_err(inst->dev, "Could not allocate buffer!"); ++ rv = -ENOMEM; ++ break; ++ } ++ smi_scatterlist_from_buffer( ++ inst, ++ inst->bounce.phys[i], ++ DMA_BOUNCE_BUFFER_SIZE, ++ &inst->bounce.sgl[i] ++ ); ++ } ++ ++ return rv; ++} ++ ++static int bcm2835_smi_probe(struct platform_device *pdev) ++{ ++ int err; ++ struct device *dev = &pdev->dev; ++ struct device_node *node = dev->of_node; ++ struct resource *ioresource; ++ struct bcm2835_smi_instance *inst; ++ const __be32 *addr; ++ ++ /* We require device tree support */ ++ if (!node) ++ return -EINVAL; ++ /* Allocate buffers and instance data */ ++ inst = devm_kzalloc(dev, sizeof(struct bcm2835_smi_instance), ++ GFP_KERNEL); ++ if (!inst) ++ return -ENOMEM; ++ ++ inst->dev = dev; ++ spin_lock_init(&inst->transaction_lock); ++ ++ ioresource = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ inst->smi_regs_ptr = devm_ioremap_resource(dev, ioresource); ++ if (IS_ERR(inst->smi_regs_ptr)) { ++ err = PTR_ERR(inst->smi_regs_ptr); ++ goto err; ++ } ++ addr = of_get_address(node, 0, NULL, NULL); ++ inst->smi_regs_busaddr = be32_to_cpu(*addr); ++ ++ err = bcm2835_smi_dma_setup(inst); ++ if (err) ++ goto err; ++ ++ /* request clock */ ++ inst->clk = devm_clk_get(dev, NULL); ++ if (!inst->clk) ++ goto err; ++ clk_prepare_enable(inst->clk); ++ ++ /* Finally, do peripheral setup */ ++ smi_setup_regs(inst); ++ ++ platform_set_drvdata(pdev, inst); ++ ++ dev_info(inst->dev, "initialised"); ++ ++ return 0; ++err: ++ kfree(inst); ++ return err; ++} ++ ++/**************************************************************************** ++* ++* bcm2835_smi_remove - called when the driver is unloaded. ++* ++***************************************************************************/ ++ ++static int bcm2835_smi_remove(struct platform_device *pdev) ++{ ++ struct bcm2835_smi_instance *inst = platform_get_drvdata(pdev); ++ struct device *dev = inst->dev; ++ ++ dmaengine_terminate_all(inst->dma_chan); ++ dma_release_channel(inst->dma_chan); ++ ++ clk_disable_unprepare(inst->clk); ++ ++ dev_info(dev, "SMI device removed - OK"); ++ return 0; ++} ++ ++/**************************************************************************** ++* ++* Register the driver with device tree ++* ++***************************************************************************/ ++ ++static const struct of_device_id bcm2835_smi_of_match[] = { ++ {.compatible = "brcm,bcm2835-smi",}, ++ { /* sentinel */ }, ++}; ++ ++MODULE_DEVICE_TABLE(of, bcm2835_smi_of_match); ++ ++static struct platform_driver bcm2835_smi_driver = { ++ .probe = bcm2835_smi_probe, ++ .remove = bcm2835_smi_remove, ++ .driver = { ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ .of_match_table = bcm2835_smi_of_match, ++ }, ++}; ++ ++module_platform_driver(bcm2835_smi_driver); ++ ++MODULE_ALIAS("platform:smi-bcm2835"); ++MODULE_LICENSE("GPL"); ++MODULE_DESCRIPTION("Device driver for BCM2835's secondary memory interface"); ++MODULE_AUTHOR("Luke Wren "); +--- /dev/null ++++ b/include/linux/broadcom/bcm2835_smi.h +@@ -0,0 +1,391 @@ ++/** ++ * Declarations and definitions for Broadcom's Secondary Memory Interface ++ * ++ * Written by Luke Wren ++ * Copyright (c) 2015, Raspberry Pi (Trading) Ltd. ++ * Copyright (c) 2010-2012 Broadcom. All rights reserved. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions ++ * are met: ++ * 1. Redistributions of source code must retain the above copyright ++ * notice, this list of conditions, and the following disclaimer, ++ * without modification. ++ * 2. Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in the ++ * documentation and/or other materials provided with the distribution. ++ * 3. The names of the above-listed copyright holders may not be used ++ * to endorse or promote products derived from this software without ++ * specific prior written permission. ++ * ++ * ALTERNATIVELY, this software may be distributed under the terms of the ++ * GNU General Public License ("GPL") version 2, as published by the Free ++ * Software Foundation. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS ++ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ++ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR ++ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR ++ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF ++ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING ++ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ */ ++ ++#ifndef BCM2835_SMI_H ++#define BCM2835_SMI_H ++ ++#include ++ ++#ifndef __KERNEL__ ++#include ++#include ++#endif ++ ++#define BCM2835_SMI_IOC_MAGIC 0x1 ++#define BCM2835_SMI_INVALID_HANDLE (~0) ++ ++/* IOCTLs 0x100...0x1ff are not device-specific - we can use them */ ++#define BCM2835_SMI_IOC_GET_SETTINGS _IO(BCM2835_SMI_IOC_MAGIC, 0) ++#define BCM2835_SMI_IOC_WRITE_SETTINGS _IO(BCM2835_SMI_IOC_MAGIC, 1) ++#define BCM2835_SMI_IOC_ADDRESS _IO(BCM2835_SMI_IOC_MAGIC, 2) ++#define BCM2835_SMI_IOC_MAX 2 ++ ++#define SMI_WIDTH_8BIT 0 ++#define SMI_WIDTH_16BIT 1 ++#define SMI_WIDTH_9BIT 2 ++#define SMI_WIDTH_18BIT 3 ++ ++/* max number of bytes where DMA will not be used */ ++#define DMA_THRESHOLD_BYTES 128 ++#define DMA_BOUNCE_BUFFER_SIZE (1024 * 1024 / 2) ++#define DMA_BOUNCE_BUFFER_COUNT 3 ++ ++ ++struct smi_settings { ++ int data_width; ++ /* Whether or not to pack multiple SMI transfers into a ++ single 32 bit FIFO word */ ++ bool pack_data; ++ ++ /* Timing for reads (writes the same but for WE) ++ * ++ * OE ----------+ +-------------------- ++ * | | ++ * +----------+ ++ * SD -<==============================>----------- ++ * SA -<=========================================>- ++ * <-setup-> <-strobe -> <-hold -> <- pace -> ++ */ ++ ++ int read_setup_time; ++ int read_hold_time; ++ int read_pace_time; ++ int read_strobe_time; ++ ++ int write_setup_time; ++ int write_hold_time; ++ int write_pace_time; ++ int write_strobe_time; ++ ++ bool dma_enable; /* DREQs */ ++ bool dma_passthrough_enable; /* External DREQs */ ++ int dma_read_thresh; ++ int dma_write_thresh; ++ int dma_panic_read_thresh; ++ int dma_panic_write_thresh; ++}; ++ ++/**************************************************************************** ++* ++* Declare exported SMI functions ++* ++***************************************************************************/ ++ ++#ifdef __KERNEL__ ++ ++#include /* for enum dma_transfer_direction */ ++#include ++#include ++ ++struct bcm2835_smi_instance; ++ ++struct bcm2835_smi_bounce_info { ++ struct semaphore callback_sem; ++ void *buffer[DMA_BOUNCE_BUFFER_COUNT]; ++ dma_addr_t phys[DMA_BOUNCE_BUFFER_COUNT]; ++ struct scatterlist sgl[DMA_BOUNCE_BUFFER_COUNT]; ++}; ++ ++ ++void bcm2835_smi_set_regs_from_settings(struct bcm2835_smi_instance *); ++ ++struct smi_settings *bcm2835_smi_get_settings_from_regs( ++ struct bcm2835_smi_instance *inst); ++ ++void bcm2835_smi_write_buf( ++ struct bcm2835_smi_instance *inst, ++ const void *buf, ++ size_t n_bytes); ++ ++void bcm2835_smi_read_buf( ++ struct bcm2835_smi_instance *inst, ++ void *buf, ++ size_t n_bytes); ++ ++void bcm2835_smi_set_address(struct bcm2835_smi_instance *inst, ++ unsigned int address); ++ ++ssize_t bcm2835_smi_user_dma( ++ struct bcm2835_smi_instance *inst, ++ enum dma_transfer_direction dma_dir, ++ char __user *user_ptr, ++ size_t count, ++ struct bcm2835_smi_bounce_info **bounce); ++ ++struct bcm2835_smi_instance *bcm2835_smi_get(struct device_node *node); ++ ++#endif /* __KERNEL__ */ ++ ++/**************************************************************** ++* ++* Implementation-only declarations ++* ++****************************************************************/ ++ ++#ifdef BCM2835_SMI_IMPLEMENTATION ++ ++/* Clock manager registers for SMI clock: */ ++#define CM_SMI_BASE_ADDRESS ((BCM2708_PERI_BASE) + 0x1010b0) ++/* Clock manager "password" to protect registers from spurious writes */ ++#define CM_PWD (0x5a << 24) ++ ++#define CM_SMI_CTL 0x00 ++#define CM_SMI_DIV 0x04 ++ ++#define CM_SMI_CTL_FLIP (1 << 8) ++#define CM_SMI_CTL_BUSY (1 << 7) ++#define CM_SMI_CTL_KILL (1 << 5) ++#define CM_SMI_CTL_ENAB (1 << 4) ++#define CM_SMI_CTL_SRC_MASK (0xf) ++#define CM_SMI_CTL_SRC_OFFS (0) ++ ++#define CM_SMI_DIV_DIVI_MASK (0xf << 12) ++#define CM_SMI_DIV_DIVI_OFFS (12) ++#define CM_SMI_DIV_DIVF_MASK (0xff << 4) ++#define CM_SMI_DIV_DIVF_OFFS (4) ++ ++/* SMI register mapping:*/ ++#define SMI_BASE_ADDRESS ((BCM2708_PERI_BASE) + 0x600000) ++ ++#define SMICS 0x00 /* control + status register */ ++#define SMIL 0x04 /* length/count (n external txfers) */ ++#define SMIA 0x08 /* address register */ ++#define SMID 0x0c /* data register */ ++#define SMIDSR0 0x10 /* device 0 read settings */ ++#define SMIDSW0 0x14 /* device 0 write settings */ ++#define SMIDSR1 0x18 /* device 1 read settings */ ++#define SMIDSW1 0x1c /* device 1 write settings */ ++#define SMIDSR2 0x20 /* device 2 read settings */ ++#define SMIDSW2 0x24 /* device 2 write settings */ ++#define SMIDSR3 0x28 /* device 3 read settings */ ++#define SMIDSW3 0x2c /* device 3 write settings */ ++#define SMIDC 0x30 /* DMA control registers */ ++#define SMIDCS 0x34 /* direct control/status register */ ++#define SMIDA 0x38 /* direct address register */ ++#define SMIDD 0x3c /* direct data registers */ ++#define SMIFD 0x40 /* FIFO debug register */ ++ ++ ++ ++/* Control and Status register bits: ++ * SMICS_RXF : RX fifo full: 1 when RX fifo is full ++ * SMICS_TXE : TX fifo empty: 1 when empty. ++ * SMICS_RXD : RX fifo contains data: 1 when there is data. ++ * SMICS_TXD : TX fifo can accept data: 1 when true. ++ * SMICS_RXR : RX fifo needs reading: 1 when fifo more than 3/4 full, or ++ * when "DONE" and fifo not emptied. ++ * SMICS_TXW : TX fifo needs writing: 1 when less than 1/4 full. ++ * SMICS_AFERR : AXI FIFO error: 1 when fifo read when empty or written ++ * when full. Write 1 to clear. ++ * SMICS_EDREQ : 1 when external DREQ received. ++ * SMICS_PXLDAT : Pixel data: write 1 to enable pixel transfer modes. ++ * SMICS_SETERR : 1 if there was an error writing to setup regs (e.g. ++ * tx was in progress). Write 1 to clear. ++ * SMICS_PVMODE : Set to 1 to enable pixel valve mode. ++ * SMICS_INTR : Set to 1 to enable interrupt on RX. ++ * SMICS_INTT : Set to 1 to enable interrupt on TX. ++ * SMICS_INTD : Set to 1 to enable interrupt on DONE condition. ++ * SMICS_TEEN : Tear effect mode enabled: Programmed transfers will wait ++ * for a TE trigger before writing. ++ * SMICS_PAD1 : Padding settings for external transfers. For writes: the ++ * number of bytes initially written to the TX fifo that ++ * SMICS_PAD0 : should be ignored. For reads: the number of bytes that will ++ * be read before the data, and should be dropped. ++ * SMICS_WRITE : Transfer direction: 1 = write to external device, 0 = read ++ * SMICS_CLEAR : Write 1 to clear the FIFOs. ++ * SMICS_START : Write 1 to start the programmed transfer. ++ * SMICS_ACTIVE : Reads as 1 when a programmed transfer is underway. ++ * SMICS_DONE : Reads as 1 when transfer finished. For RX, not set until ++ * FIFO emptied. ++ * SMICS_ENABLE : Set to 1 to enable the SMI peripheral, 0 to disable. ++ */ ++ ++#define SMICS_RXF (1 << 31) ++#define SMICS_TXE (1 << 30) ++#define SMICS_RXD (1 << 29) ++#define SMICS_TXD (1 << 28) ++#define SMICS_RXR (1 << 27) ++#define SMICS_TXW (1 << 26) ++#define SMICS_AFERR (1 << 25) ++#define SMICS_EDREQ (1 << 15) ++#define SMICS_PXLDAT (1 << 14) ++#define SMICS_SETERR (1 << 13) ++#define SMICS_PVMODE (1 << 12) ++#define SMICS_INTR (1 << 11) ++#define SMICS_INTT (1 << 10) ++#define SMICS_INTD (1 << 9) ++#define SMICS_TEEN (1 << 8) ++#define SMICS_PAD1 (1 << 7) ++#define SMICS_PAD0 (1 << 6) ++#define SMICS_WRITE (1 << 5) ++#define SMICS_CLEAR (1 << 4) ++#define SMICS_START (1 << 3) ++#define SMICS_ACTIVE (1 << 2) ++#define SMICS_DONE (1 << 1) ++#define SMICS_ENABLE (1 << 0) ++ ++/* Address register bits: */ ++ ++#define SMIA_DEVICE_MASK ((1 << 9) | (1 << 8)) ++#define SMIA_DEVICE_OFFS (8) ++#define SMIA_ADDR_MASK (0x3f) /* bits 5 -> 0 */ ++#define SMIA_ADDR_OFFS (0) ++ ++/* DMA control register bits: ++ * SMIDC_DMAEN : DMA enable: set 1: DMA requests will be issued. ++ * SMIDC_DMAP : DMA passthrough: when set to 0, top two data pins are used by ++ * SMI as usual. When set to 1, the top two pins are used for ++ * external DREQs: pin 16 read request, 17 write. ++ * SMIDC_PANIC* : Threshold at which DMA will panic during read/write. ++ * SMIDC_REQ* : Threshold at which DMA will generate a DREQ. ++ */ ++ ++#define SMIDC_DMAEN (1 << 28) ++#define SMIDC_DMAP (1 << 24) ++#define SMIDC_PANICR_MASK (0x3f << 18) ++#define SMIDC_PANICR_OFFS (18) ++#define SMIDC_PANICW_MASK (0x3f << 12) ++#define SMIDC_PANICW_OFFS (12) ++#define SMIDC_REQR_MASK (0x3f << 6) ++#define SMIDC_REQR_OFFS (6) ++#define SMIDC_REQW_MASK (0x3f) ++#define SMIDC_REQW_OFFS (0) ++ ++/* Device settings register bits: same for all 4 (or 3?) device register sets. ++ * Device read settings: ++ * SMIDSR_RWIDTH : Read transfer width. 00 = 8bit, 01 = 16bit, ++ * 10 = 18bit, 11 = 9bit. ++ * SMIDSR_RSETUP : Read setup time: number of core cycles between chip ++ * select/address and read strobe. Min 1, max 64. ++ * SMIDSR_MODE68 : 1 for System 68 mode (i.e. enable + direction pins, ++ * rather than OE + WE pin) ++ * SMIDSR_FSETUP : If set to 1, setup time only applies to first ++ * transfer after address change. ++ * SMIDSR_RHOLD : Number of core cycles between read strobe going ++ * inactive and CS/address going inactive. Min 1, max 64 ++ * SMIDSR_RPACEALL : When set to 1, this device's RPACE value will always ++ * be used for the next transaction, even if it is not ++ * to this device. ++ * SMIDSR_RPACE : Number of core cycles spent waiting between CS ++ * deassert and start of next transfer. Min 1, max 128 ++ * SMIDSR_RDREQ : 1 = use external DMA request on SD16 to pace reads ++ * from device. Must also set DMAP in SMICS. ++ * SMIDSR_RSTROBE : Number of cycles to assert the read strobe. ++ * min 1, max 128. ++ */ ++#define SMIDSR_RWIDTH_MASK ((1<<31)|(1<<30)) ++#define SMIDSR_RWIDTH_OFFS (30) ++#define SMIDSR_RSETUP_MASK (0x3f << 24) ++#define SMIDSR_RSETUP_OFFS (24) ++#define SMIDSR_MODE68 (1 << 23) ++#define SMIDSR_FSETUP (1 << 22) ++#define SMIDSR_RHOLD_MASK (0x3f << 16) ++#define SMIDSR_RHOLD_OFFS (16) ++#define SMIDSR_RPACEALL (1 << 15) ++#define SMIDSR_RPACE_MASK (0x7f << 8) ++#define SMIDSR_RPACE_OFFS (8) ++#define SMIDSR_RDREQ (1 << 7) ++#define SMIDSR_RSTROBE_MASK (0x7f) ++#define SMIDSR_RSTROBE_OFFS (0) ++ ++/* Device write settings: ++ * SMIDSW_WWIDTH : Write transfer width. 00 = 8bit, 01 = 16bit, ++ * 10= 18bit, 11 = 9bit. ++ * SMIDSW_WSETUP : Number of cycles between CS assert and write strobe. ++ * Min 1, max 64. ++ * SMIDSW_WFORMAT : Pixel format of input. 0 = 16bit RGB 565, ++ * 1 = 32bit RGBA 8888 ++ * SMIDSW_WSWAP : 1 = swap pixel data bits. (Use with SMICS_PXLDAT) ++ * SMIDSW_WHOLD : Time between WE deassert and CS deassert. 1 to 64 ++ * SMIDSW_WPACEALL : 1: this device's WPACE will be used for the next ++ * transfer, regardless of that transfer's device. ++ * SMIDSW_WPACE : Cycles between CS deassert and next CS assert. ++ * Min 1, max 128 ++ * SMIDSW_WDREQ : Use external DREQ on pin 17 to pace writes. DMAP must ++ * be set in SMICS. ++ * SMIDSW_WSTROBE : Number of cycles to assert the write strobe. ++ * Min 1, max 128 ++ */ ++#define SMIDSW_WWIDTH_MASK ((1<<31)|(1<<30)) ++#define SMIDSW_WWIDTH_OFFS (30) ++#define SMIDSW_WSETUP_MASK (0x3f << 24) ++#define SMIDSW_WSETUP_OFFS (24) ++#define SMIDSW_WFORMAT (1 << 23) ++#define SMIDSW_WSWAP (1 << 22) ++#define SMIDSW_WHOLD_MASK (0x3f << 16) ++#define SMIDSW_WHOLD_OFFS (16) ++#define SMIDSW_WPACEALL (1 << 15) ++#define SMIDSW_WPACE_MASK (0x7f << 8) ++#define SMIDSW_WPACE_OFFS (8) ++#define SMIDSW_WDREQ (1 << 7) ++#define SMIDSW_WSTROBE_MASK (0x7f) ++#define SMIDSW_WSTROBE_OFFS (0) ++ ++/* Direct transfer control + status register ++ * SMIDCS_WRITE : Direction of transfer: 1 -> write, 0 -> read ++ * SMIDCS_DONE : 1 when a transfer has finished. Write 1 to clear. ++ * SMIDCS_START : Write 1 to start a transfer, if one is not already underway. ++ * SMIDCE_ENABLE: Write 1 to enable SMI in direct mode. ++ */ ++ ++#define SMIDCS_WRITE (1 << 3) ++#define SMIDCS_DONE (1 << 2) ++#define SMIDCS_START (1 << 1) ++#define SMIDCS_ENABLE (1 << 0) ++ ++/* Direct transfer address register ++ * SMIDA_DEVICE : Indicates which of the device settings banks should be used. ++ * SMIDA_ADDR : The value to be asserted on the address pins. ++ */ ++ ++#define SMIDA_DEVICE_MASK ((1<<9)|(1<<8)) ++#define SMIDA_DEVICE_OFFS (8) ++#define SMIDA_ADDR_MASK (0x3f) ++#define SMIDA_ADDR_OFFS (0) ++ ++/* FIFO debug register ++ * SMIFD_FLVL : The high-tide mark of FIFO count during the most recent txfer ++ * SMIFD_FCNT : The current FIFO count. ++ */ ++#define SMIFD_FLVL_MASK (0x3f << 8) ++#define SMIFD_FLVL_OFFS (8) ++#define SMIFD_FCNT_MASK (0x3f) ++#define SMIFD_FCNT_OFFS (0) ++ ++#endif /* BCM2835_SMI_IMPLEMENTATION */ ++ ++#endif /* BCM2835_SMI_H */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0051-Add-Chris-Boot-s-i2c-driver.patch b/target/linux/bcm27xx/patches-5.10/950-0051-Add-Chris-Boot-s-i2c-driver.patch new file mode 100644 index 0000000000..8d97412bcc --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0051-Add-Chris-Boot-s-i2c-driver.patch @@ -0,0 +1,660 @@ +From 8e6989f4270ffc86166cbab697b1f539f4cdeb03 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Wed, 17 Jun 2015 15:44:08 +0100 +Subject: [PATCH] Add Chris Boot's i2c driver +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +i2c-bcm2708: fixed baudrate + +Fixed issue where the wrong CDIV value was set for baudrates below 3815 Hz (for 250MHz bus clock). +In that case the computed CDIV value was more than 0xffff. However the CDIV register width is only 16 bits. +This resulted in incorrect setting of CDIV and higher baudrate than intended. +Example: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0x1704 -> 42430Hz +After correction: 3500Hz -> CDIV=0x11704 -> CDIV(16bit)=0xffff -> 3815Hz +The correct baudrate is shown in the log after the cdiv > 0xffff correction. + +Perform I2C combined transactions when possible + +Perform I2C combined transactions whenever possible, within the +restrictions of the Broadcomm Serial Controller. + +Disable DONE interrupt during TA poll + +Prevent interrupt from being triggered if poll is missed and transfer +starts and finishes. + +i2c: Make combined transactions optional and disabled by default + +i2c: bcm2708: add device tree support + +Add DT support to driver and add to .dtsi file. +Setup pins in .dts file. +i2c is disabled by default. + +Signed-off-by: Noralf Tronnes + +bcm2708: don't register i2c controllers when using DT + +The devices for the i2c controllers are in the Device Tree. +Only register devices when not using DT. + +Signed-off-by: Noralf Tronnes + +I2C: Only register the I2C device for the current board revision + +i2c_bcm2708: Fix clock reference counting + +Fix grabbing lock from atomic context in i2c driver + +2 main changes: +- check for timeouts in the bcm2708_bsc_setup function as indicated by this comment: + /* poll for transfer start bit (should only take 1-20 polls) */ + This implies that the setup function can now fail so account for this everywhere it's called +- Removed the clk_get_rate call from inside the setup function as it locks a mutex and that's not ok since we call it from under a spin lock. + +i2c-bcm2708: When using DT, leave the GPIO setup to pinctrl + +i2c-bcm2708: Increase timeouts to allow larger transfers + +Use the timeout value provided by the I2C_TIMEOUT ioctl when waiting +for completion. The default timeout is 1 second. + +See: https://github.com/raspberrypi/linux/issues/260 + +i2c-bcm2708/BCM270X_DT: Add support for I2C2 + +The third I2C bus (I2C2) is normally reserved for HDMI use. Careless +use of this bus can break an attached display - use with caution. + +It is recommended to disable accesses by VideoCore by setting +hdmi_ignore_edid=1 or hdmi_edid_file=1 in config.txt. + +The interface is disabled by default - enable using the +i2c2_iknowwhatimdoing DT parameter. + +bcm2708-spi: Don't use static pin configuration with DT + +Also remove superfluous error checking - the SPI framework ensures the +validity of the chip_select value. + +i2c-bcm2708: Remove non-DT support + +Signed-off-by: Noralf Trønnes + +Set the BSC_CLKT clock streching timeout to 35ms as per SMBus specs. + +Fixes i2c_bcm2708: Write to FIFO correctly - v2 (#1574) + +* i2c: fix i2c_bcm2708: Clear FIFO before sending data + +Make sure FIFO gets cleared before trying to send +data in case of a repeated start (COMBINED=Y). + +* i2c: fix i2c_bcm2708: Only write to FIFO when not full + +Check if FIFO can accept data before writing. +To avoid a peripheral read on the last iteration of a loop, +both bcm2708_bsc_fifo_fill and ~drain are changed as well. +--- + drivers/i2c/busses/Kconfig | 19 ++ + drivers/i2c/busses/Makefile | 2 + + drivers/i2c/busses/i2c-bcm2708.c | 512 +++++++++++++++++++++++++++++++ + 3 files changed, 533 insertions(+) + create mode 100644 drivers/i2c/busses/i2c-bcm2708.c + +--- a/drivers/i2c/busses/Kconfig ++++ b/drivers/i2c/busses/Kconfig +@@ -9,6 +9,25 @@ menu "I2C Hardware Bus support" + comment "PC SMBus host controller drivers" + depends on PCI + ++config I2C_BCM2708 ++ tristate "BCM2708 BSC" ++ depends on ARCH_BCM2835 ++ help ++ Enabling this option will add BSC (Broadcom Serial Controller) ++ support for the BCM2708. BSC is a Broadcom proprietary bus compatible ++ with I2C/TWI/SMBus. ++ ++config I2C_BCM2708_BAUDRATE ++ prompt "BCM2708 I2C baudrate" ++ depends on I2C_BCM2708 ++ int ++ default 100000 ++ help ++ Set the I2C baudrate. This will alter the default value. A ++ different baudrate can be set by using a module parameter as well. If ++ no parameter is provided when loading, this is the value that will be ++ used. ++ + config I2C_ALI1535 + tristate "ALI 1535" + depends on PCI +--- a/drivers/i2c/busses/Makefile ++++ b/drivers/i2c/busses/Makefile +@@ -3,6 +3,8 @@ + # Makefile for the i2c bus drivers. + # + ++obj-$(CONFIG_I2C_BCM2708) += i2c-bcm2708.o ++ + # ACPI drivers + obj-$(CONFIG_I2C_SCMI) += i2c-scmi.o + +--- /dev/null ++++ b/drivers/i2c/busses/i2c-bcm2708.c +@@ -0,0 +1,512 @@ ++/* ++ * Driver for Broadcom BCM2708 BSC Controllers ++ * ++ * Copyright (C) 2012 Chris Boot & Frank Buss ++ * ++ * This driver is inspired by: ++ * i2c-ocores.c, by Peter Korsgaard ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License as published by ++ * the Free Software Foundation; either version 2 of the License, or ++ * (at your option) any later version. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++/* BSC register offsets */ ++#define BSC_C 0x00 ++#define BSC_S 0x04 ++#define BSC_DLEN 0x08 ++#define BSC_A 0x0c ++#define BSC_FIFO 0x10 ++#define BSC_DIV 0x14 ++#define BSC_DEL 0x18 ++#define BSC_CLKT 0x1c ++ ++/* Bitfields in BSC_C */ ++#define BSC_C_I2CEN 0x00008000 ++#define BSC_C_INTR 0x00000400 ++#define BSC_C_INTT 0x00000200 ++#define BSC_C_INTD 0x00000100 ++#define BSC_C_ST 0x00000080 ++#define BSC_C_CLEAR_1 0x00000020 ++#define BSC_C_CLEAR_2 0x00000010 ++#define BSC_C_READ 0x00000001 ++ ++/* Bitfields in BSC_S */ ++#define BSC_S_CLKT 0x00000200 ++#define BSC_S_ERR 0x00000100 ++#define BSC_S_RXF 0x00000080 ++#define BSC_S_TXE 0x00000040 ++#define BSC_S_RXD 0x00000020 ++#define BSC_S_TXD 0x00000010 ++#define BSC_S_RXR 0x00000008 ++#define BSC_S_TXW 0x00000004 ++#define BSC_S_DONE 0x00000002 ++#define BSC_S_TA 0x00000001 ++ ++#define I2C_WAIT_LOOP_COUNT 200 ++ ++#define DRV_NAME "bcm2708_i2c" ++ ++static unsigned int baudrate; ++module_param(baudrate, uint, S_IRUSR | S_IWUSR | S_IRGRP | S_IWGRP); ++MODULE_PARM_DESC(baudrate, "The I2C baudrate"); ++ ++static bool combined = false; ++module_param(combined, bool, 0644); ++MODULE_PARM_DESC(combined, "Use combined transactions"); ++ ++struct bcm2708_i2c { ++ struct i2c_adapter adapter; ++ ++ spinlock_t lock; ++ void __iomem *base; ++ int irq; ++ struct clk *clk; ++ u32 cdiv; ++ u32 clk_tout; ++ ++ struct completion done; ++ ++ struct i2c_msg *msg; ++ int pos; ++ int nmsgs; ++ bool error; ++}; ++ ++static inline u32 bcm2708_rd(struct bcm2708_i2c *bi, unsigned reg) ++{ ++ return readl(bi->base + reg); ++} ++ ++static inline void bcm2708_wr(struct bcm2708_i2c *bi, unsigned reg, u32 val) ++{ ++ writel(val, bi->base + reg); ++} ++ ++static inline void bcm2708_bsc_reset(struct bcm2708_i2c *bi) ++{ ++ bcm2708_wr(bi, BSC_C, 0); ++ bcm2708_wr(bi, BSC_S, BSC_S_CLKT | BSC_S_ERR | BSC_S_DONE); ++} ++ ++static inline void bcm2708_bsc_fifo_drain(struct bcm2708_i2c *bi) ++{ ++ while ((bi->pos < bi->msg->len) && (bcm2708_rd(bi, BSC_S) & BSC_S_RXD)) ++ bi->msg->buf[bi->pos++] = bcm2708_rd(bi, BSC_FIFO); ++} ++ ++static inline void bcm2708_bsc_fifo_fill(struct bcm2708_i2c *bi) ++{ ++ while ((bi->pos < bi->msg->len) && (bcm2708_rd(bi, BSC_S) & BSC_S_TXD)) ++ bcm2708_wr(bi, BSC_FIFO, bi->msg->buf[bi->pos++]); ++} ++ ++static inline int bcm2708_bsc_setup(struct bcm2708_i2c *bi) ++{ ++ u32 cdiv, s, clk_tout; ++ u32 c = BSC_C_I2CEN | BSC_C_INTD | BSC_C_ST | BSC_C_CLEAR_1; ++ int wait_loops = I2C_WAIT_LOOP_COUNT; ++ ++ /* Can't call clk_get_rate as it locks a mutex and here we are spinlocked. ++ * Use the value that we cached in the probe. ++ */ ++ cdiv = bi->cdiv; ++ clk_tout = bi->clk_tout; ++ ++ if (bi->msg->flags & I2C_M_RD) ++ c |= BSC_C_INTR | BSC_C_READ; ++ else ++ c |= BSC_C_INTT; ++ ++ bcm2708_wr(bi, BSC_CLKT, clk_tout); ++ bcm2708_wr(bi, BSC_DIV, cdiv); ++ bcm2708_wr(bi, BSC_A, bi->msg->addr); ++ bcm2708_wr(bi, BSC_DLEN, bi->msg->len); ++ if (combined) ++ { ++ /* Do the next two messages meet combined transaction criteria? ++ - Current message is a write, next message is a read ++ - Both messages to same slave address ++ - Write message can fit inside FIFO (16 bytes or less) */ ++ if ( (bi->nmsgs > 1) && ++ !(bi->msg[0].flags & I2C_M_RD) && (bi->msg[1].flags & I2C_M_RD) && ++ (bi->msg[0].addr == bi->msg[1].addr) && (bi->msg[0].len <= 16)) { ++ ++ /* Clear FIFO */ ++ bcm2708_wr(bi, BSC_C, BSC_C_CLEAR_1); ++ ++ /* Fill FIFO with entire write message (16 byte FIFO) */ ++ while (bi->pos < bi->msg->len) { ++ bcm2708_wr(bi, BSC_FIFO, bi->msg->buf[bi->pos++]); ++ } ++ /* Start write transfer (no interrupts, don't clear FIFO) */ ++ bcm2708_wr(bi, BSC_C, BSC_C_I2CEN | BSC_C_ST); ++ ++ /* poll for transfer start bit (should only take 1-20 polls) */ ++ do { ++ s = bcm2708_rd(bi, BSC_S); ++ } while (!(s & (BSC_S_TA | BSC_S_ERR | BSC_S_CLKT | BSC_S_DONE)) && --wait_loops >= 0); ++ ++ /* did we time out or some error occured? */ ++ if (wait_loops < 0 || (s & (BSC_S_ERR | BSC_S_CLKT))) { ++ return -1; ++ } ++ ++ /* Send next read message before the write transfer finishes. */ ++ bi->nmsgs--; ++ bi->msg++; ++ bi->pos = 0; ++ bcm2708_wr(bi, BSC_DLEN, bi->msg->len); ++ c = BSC_C_I2CEN | BSC_C_INTD | BSC_C_INTR | BSC_C_ST | BSC_C_READ; ++ } ++ } ++ bcm2708_wr(bi, BSC_C, c); ++ ++ return 0; ++} ++ ++static irqreturn_t bcm2708_i2c_interrupt(int irq, void *dev_id) ++{ ++ struct bcm2708_i2c *bi = dev_id; ++ bool handled = true; ++ u32 s; ++ int ret; ++ ++ spin_lock(&bi->lock); ++ ++ /* we may see camera interrupts on the "other" I2C channel ++ Just return if we've not sent anything */ ++ if (!bi->nmsgs || !bi->msg) { ++ goto early_exit; ++ } ++ ++ s = bcm2708_rd(bi, BSC_S); ++ ++ if (s & (BSC_S_CLKT | BSC_S_ERR)) { ++ bcm2708_bsc_reset(bi); ++ bi->error = true; ++ ++ bi->msg = 0; /* to inform the that all work is done */ ++ bi->nmsgs = 0; ++ /* wake up our bh */ ++ complete(&bi->done); ++ } else if (s & BSC_S_DONE) { ++ bi->nmsgs--; ++ ++ if (bi->msg->flags & I2C_M_RD) { ++ bcm2708_bsc_fifo_drain(bi); ++ } ++ ++ bcm2708_bsc_reset(bi); ++ ++ if (bi->nmsgs) { ++ /* advance to next message */ ++ bi->msg++; ++ bi->pos = 0; ++ ret = bcm2708_bsc_setup(bi); ++ if (ret < 0) { ++ bcm2708_bsc_reset(bi); ++ bi->error = true; ++ bi->msg = 0; /* to inform the that all work is done */ ++ bi->nmsgs = 0; ++ /* wake up our bh */ ++ complete(&bi->done); ++ goto early_exit; ++ } ++ } else { ++ bi->msg = 0; /* to inform the that all work is done */ ++ bi->nmsgs = 0; ++ /* wake up our bh */ ++ complete(&bi->done); ++ } ++ } else if (s & BSC_S_TXW) { ++ bcm2708_bsc_fifo_fill(bi); ++ } else if (s & BSC_S_RXR) { ++ bcm2708_bsc_fifo_drain(bi); ++ } else { ++ handled = false; ++ } ++ ++early_exit: ++ spin_unlock(&bi->lock); ++ ++ return handled ? IRQ_HANDLED : IRQ_NONE; ++} ++ ++static int bcm2708_i2c_master_xfer(struct i2c_adapter *adap, ++ struct i2c_msg *msgs, int num) ++{ ++ struct bcm2708_i2c *bi = adap->algo_data; ++ unsigned long flags; ++ int ret; ++ ++ spin_lock_irqsave(&bi->lock, flags); ++ ++ reinit_completion(&bi->done); ++ bi->msg = msgs; ++ bi->pos = 0; ++ bi->nmsgs = num; ++ bi->error = false; ++ ++ ret = bcm2708_bsc_setup(bi); ++ ++ spin_unlock_irqrestore(&bi->lock, flags); ++ ++ /* check the result of the setup */ ++ if (ret < 0) ++ { ++ dev_err(&adap->dev, "transfer setup timed out\n"); ++ goto error_timeout; ++ } ++ ++ ret = wait_for_completion_timeout(&bi->done, adap->timeout); ++ if (ret == 0) { ++ dev_err(&adap->dev, "transfer timed out\n"); ++ goto error_timeout; ++ } ++ ++ ret = bi->error ? -EIO : num; ++ return ret; ++ ++error_timeout: ++ spin_lock_irqsave(&bi->lock, flags); ++ bcm2708_bsc_reset(bi); ++ bi->msg = 0; /* to inform the interrupt handler that there's nothing else to be done */ ++ bi->nmsgs = 0; ++ spin_unlock_irqrestore(&bi->lock, flags); ++ return -ETIMEDOUT; ++} ++ ++static u32 bcm2708_i2c_functionality(struct i2c_adapter *adap) ++{ ++ return I2C_FUNC_I2C | /*I2C_FUNC_10BIT_ADDR |*/ I2C_FUNC_SMBUS_EMUL; ++} ++ ++static struct i2c_algorithm bcm2708_i2c_algorithm = { ++ .master_xfer = bcm2708_i2c_master_xfer, ++ .functionality = bcm2708_i2c_functionality, ++}; ++ ++static int bcm2708_i2c_probe(struct platform_device *pdev) ++{ ++ struct resource *regs; ++ int irq, err = -ENOMEM; ++ struct clk *clk; ++ struct bcm2708_i2c *bi; ++ struct i2c_adapter *adap; ++ unsigned long bus_hz; ++ u32 cdiv, clk_tout; ++ u32 baud; ++ ++ baud = CONFIG_I2C_BCM2708_BAUDRATE; ++ ++ if (pdev->dev.of_node) { ++ u32 bus_clk_rate; ++ pdev->id = of_alias_get_id(pdev->dev.of_node, "i2c"); ++ if (pdev->id < 0) { ++ dev_err(&pdev->dev, "alias is missing\n"); ++ return -EINVAL; ++ } ++ if (!of_property_read_u32(pdev->dev.of_node, ++ "clock-frequency", &bus_clk_rate)) ++ baud = bus_clk_rate; ++ else ++ dev_warn(&pdev->dev, ++ "Could not read clock-frequency property\n"); ++ } ++ ++ if (baudrate) ++ baud = baudrate; ++ ++ regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ if (!regs) { ++ dev_err(&pdev->dev, "could not get IO memory\n"); ++ return -ENXIO; ++ } ++ ++ irq = platform_get_irq(pdev, 0); ++ if (irq < 0) { ++ dev_err(&pdev->dev, "could not get IRQ\n"); ++ return irq; ++ } ++ ++ clk = clk_get(&pdev->dev, NULL); ++ if (IS_ERR(clk)) { ++ dev_err(&pdev->dev, "could not find clk: %ld\n", PTR_ERR(clk)); ++ return PTR_ERR(clk); ++ } ++ ++ err = clk_prepare_enable(clk); ++ if (err) { ++ dev_err(&pdev->dev, "could not enable clk: %d\n", err); ++ goto out_clk_put; ++ } ++ ++ bi = kzalloc(sizeof(*bi), GFP_KERNEL); ++ if (!bi) ++ goto out_clk_disable; ++ ++ platform_set_drvdata(pdev, bi); ++ ++ adap = &bi->adapter; ++ adap->class = I2C_CLASS_HWMON | I2C_CLASS_DDC; ++ adap->algo = &bcm2708_i2c_algorithm; ++ adap->algo_data = bi; ++ adap->dev.parent = &pdev->dev; ++ adap->nr = pdev->id; ++ strlcpy(adap->name, dev_name(&pdev->dev), sizeof(adap->name)); ++ adap->dev.of_node = pdev->dev.of_node; ++ ++ switch (pdev->id) { ++ case 0: ++ adap->class = I2C_CLASS_HWMON; ++ break; ++ case 1: ++ adap->class = I2C_CLASS_DDC; ++ break; ++ case 2: ++ adap->class = I2C_CLASS_DDC; ++ break; ++ default: ++ dev_err(&pdev->dev, "can only bind to BSC 0, 1 or 2\n"); ++ err = -ENXIO; ++ goto out_free_bi; ++ } ++ ++ spin_lock_init(&bi->lock); ++ init_completion(&bi->done); ++ ++ bi->base = ioremap(regs->start, resource_size(regs)); ++ if (!bi->base) { ++ dev_err(&pdev->dev, "could not remap memory\n"); ++ goto out_free_bi; ++ } ++ ++ bi->irq = irq; ++ bi->clk = clk; ++ ++ err = request_irq(irq, bcm2708_i2c_interrupt, IRQF_SHARED, ++ dev_name(&pdev->dev), bi); ++ if (err) { ++ dev_err(&pdev->dev, "could not request IRQ: %d\n", err); ++ goto out_iounmap; ++ } ++ ++ bcm2708_bsc_reset(bi); ++ ++ err = i2c_add_numbered_adapter(adap); ++ if (err < 0) { ++ dev_err(&pdev->dev, "could not add I2C adapter: %d\n", err); ++ goto out_free_irq; ++ } ++ ++ bus_hz = clk_get_rate(bi->clk); ++ cdiv = bus_hz / baud; ++ if (cdiv > 0xffff) { ++ cdiv = 0xffff; ++ baud = bus_hz / cdiv; ++ } ++ ++ clk_tout = 35/1000*baud; //35ms timeout as per SMBus specs. ++ if (clk_tout > 0xffff) ++ clk_tout = 0xffff; ++ ++ bi->cdiv = cdiv; ++ bi->clk_tout = clk_tout; ++ ++ dev_info(&pdev->dev, "BSC%d Controller at 0x%08lx (irq %d) (baudrate %d)\n", ++ pdev->id, (unsigned long)regs->start, irq, baud); ++ ++ return 0; ++ ++out_free_irq: ++ free_irq(bi->irq, bi); ++out_iounmap: ++ iounmap(bi->base); ++out_free_bi: ++ kfree(bi); ++out_clk_disable: ++ clk_disable_unprepare(clk); ++out_clk_put: ++ clk_put(clk); ++ return err; ++} ++ ++static int bcm2708_i2c_remove(struct platform_device *pdev) ++{ ++ struct bcm2708_i2c *bi = platform_get_drvdata(pdev); ++ ++ platform_set_drvdata(pdev, NULL); ++ ++ i2c_del_adapter(&bi->adapter); ++ free_irq(bi->irq, bi); ++ iounmap(bi->base); ++ clk_disable_unprepare(bi->clk); ++ clk_put(bi->clk); ++ kfree(bi); ++ ++ return 0; ++} ++ ++static const struct of_device_id bcm2708_i2c_of_match[] = { ++ { .compatible = "brcm,bcm2708-i2c" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, bcm2708_i2c_of_match); ++ ++static struct platform_driver bcm2708_i2c_driver = { ++ .driver = { ++ .name = DRV_NAME, ++ .owner = THIS_MODULE, ++ .of_match_table = bcm2708_i2c_of_match, ++ }, ++ .probe = bcm2708_i2c_probe, ++ .remove = bcm2708_i2c_remove, ++}; ++ ++// module_platform_driver(bcm2708_i2c_driver); ++ ++ ++static int __init bcm2708_i2c_init(void) ++{ ++ return platform_driver_register(&bcm2708_i2c_driver); ++} ++ ++static void __exit bcm2708_i2c_exit(void) ++{ ++ platform_driver_unregister(&bcm2708_i2c_driver); ++} ++ ++module_init(bcm2708_i2c_init); ++module_exit(bcm2708_i2c_exit); ++ ++ ++ ++MODULE_DESCRIPTION("BSC controller driver for Broadcom BCM2708"); ++MODULE_AUTHOR("Chris Boot "); ++MODULE_LICENSE("GPL v2"); ++MODULE_ALIAS("platform:" DRV_NAME); diff --git a/target/linux/bcm27xx/patches-5.10/950-0052-char-broadcom-Add-vcio-module.patch b/target/linux/bcm27xx/patches-5.10/950-0052-char-broadcom-Add-vcio-module.patch new file mode 100644 index 0000000000..9d3260b121 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0052-char-broadcom-Add-vcio-module.patch @@ -0,0 +1,254 @@ +From ee17bae9c9f8fbe02644f13c01c6dd06e9c4bbc3 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= +Date: Fri, 26 Jun 2015 14:27:06 +0200 +Subject: [PATCH] char: broadcom: Add vcio module +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Add module for accessing the mailbox property channel through +/dev/vcio. Was previously in bcm2708-vcio. + +Signed-off-by: Noralf Trønnes + +char: vcio: Add compat ioctl handling + +There was no compat ioctl handler, so 32 bit userspace on a +64 bit kernel failed as IOCTL_MBOX_PROPERTY used the size +of char*. + +Signed-off-by: Dave Stevenson + +char: vcio: Fail probe if rpi_firmware is not found. + +Device Tree is now the only supported config mechanism, therefore +uncomment the block of code that fails the probe if the +firmware node can't be found. + +Signed-off-by: Dave Stevenson +--- + drivers/char/broadcom/Kconfig | 6 + + drivers/char/broadcom/Makefile | 1 + + drivers/char/broadcom/vcio.c | 194 +++++++++++++++++++++++++++++++++ + 3 files changed, 201 insertions(+) + create mode 100644 drivers/char/broadcom/vcio.c + +--- a/drivers/char/broadcom/Kconfig ++++ b/drivers/char/broadcom/Kconfig +@@ -15,6 +15,12 @@ config BCM2708_VCMEM + help + Helper for videocore memory access and total size allocation. + ++config BCM_VCIO ++ tristate "Mailbox userspace access" ++ depends on BCM2835_MBOX ++ help ++ Gives access to the mailbox property channel from userspace. ++ + endif + + config BCM2835_DEVGPIOMEM +--- a/drivers/char/broadcom/Makefile ++++ b/drivers/char/broadcom/Makefile +@@ -1,3 +1,4 @@ + obj-$(CONFIG_BCM2708_VCMEM) += vc_mem.o ++obj-$(CONFIG_BCM_VCIO) += vcio.o + obj-$(CONFIG_BCM2835_DEVGPIOMEM)+= bcm2835-gpiomem.o + obj-$(CONFIG_BCM2835_SMI_DEV) += bcm2835_smi_dev.o +--- /dev/null ++++ b/drivers/char/broadcom/vcio.c +@@ -0,0 +1,194 @@ ++/* ++ * Copyright (C) 2010 Broadcom ++ * Copyright (C) 2015 Noralf Trønnes ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define MBOX_CHAN_PROPERTY 8 ++ ++#define VCIO_IOC_MAGIC 100 ++#define IOCTL_MBOX_PROPERTY _IOWR(VCIO_IOC_MAGIC, 0, char *) ++#ifdef CONFIG_COMPAT ++#define IOCTL_MBOX_PROPERTY32 _IOWR(VCIO_IOC_MAGIC, 0, compat_uptr_t) ++#endif ++ ++static struct { ++ dev_t devt; ++ struct cdev cdev; ++ struct class *class; ++ struct rpi_firmware *fw; ++} vcio; ++ ++static int vcio_user_property_list(void *user) ++{ ++ u32 *buf, size; ++ int ret; ++ ++ /* The first 32-bit is the size of the buffer */ ++ if (copy_from_user(&size, user, sizeof(size))) ++ return -EFAULT; ++ ++ buf = kmalloc(size, GFP_KERNEL); ++ if (!buf) ++ return -ENOMEM; ++ ++ if (copy_from_user(buf, user, size)) { ++ kfree(buf); ++ return -EFAULT; ++ } ++ ++ /* Strip off protocol encapsulation */ ++ ret = rpi_firmware_property_list(vcio.fw, &buf[2], size - 12); ++ if (ret) { ++ kfree(buf); ++ return ret; ++ } ++ ++ buf[1] = RPI_FIRMWARE_STATUS_SUCCESS; ++ if (copy_to_user(user, buf, size)) ++ ret = -EFAULT; ++ ++ kfree(buf); ++ ++ return ret; ++} ++ ++static int vcio_device_open(struct inode *inode, struct file *file) ++{ ++ try_module_get(THIS_MODULE); ++ ++ return 0; ++} ++ ++static int vcio_device_release(struct inode *inode, struct file *file) ++{ ++ module_put(THIS_MODULE); ++ ++ return 0; ++} ++ ++static long vcio_device_ioctl(struct file *file, unsigned int ioctl_num, ++ unsigned long ioctl_param) ++{ ++ switch (ioctl_num) { ++ case IOCTL_MBOX_PROPERTY: ++ return vcio_user_property_list((void *)ioctl_param); ++ default: ++ pr_err("unknown ioctl: %x\n", ioctl_num); ++ return -EINVAL; ++ } ++} ++ ++#ifdef CONFIG_COMPAT ++static long vcio_device_compat_ioctl(struct file *file, unsigned int ioctl_num, ++ unsigned long ioctl_param) ++{ ++ switch (ioctl_num) { ++ case IOCTL_MBOX_PROPERTY32: ++ return vcio_user_property_list(compat_ptr(ioctl_param)); ++ default: ++ pr_err("unknown ioctl: %x\n", ioctl_num); ++ return -EINVAL; ++ } ++} ++#endif ++ ++const struct file_operations vcio_fops = { ++ .unlocked_ioctl = vcio_device_ioctl, ++#ifdef CONFIG_COMPAT ++ .compat_ioctl = vcio_device_compat_ioctl, ++#endif ++ .open = vcio_device_open, ++ .release = vcio_device_release, ++}; ++ ++static int __init vcio_init(void) ++{ ++ struct device_node *np; ++ static struct device *dev; ++ int ret; ++ ++ np = of_find_compatible_node(NULL, NULL, ++ "raspberrypi,bcm2835-firmware"); ++ if (!of_device_is_available(np)) ++ return -ENODEV; ++ ++ vcio.fw = rpi_firmware_get(np); ++ if (!vcio.fw) ++ return -ENODEV; ++ ++ ret = alloc_chrdev_region(&vcio.devt, 0, 1, "vcio"); ++ if (ret) { ++ pr_err("failed to allocate device number\n"); ++ return ret; ++ } ++ ++ cdev_init(&vcio.cdev, &vcio_fops); ++ vcio.cdev.owner = THIS_MODULE; ++ ret = cdev_add(&vcio.cdev, vcio.devt, 1); ++ if (ret) { ++ pr_err("failed to register device\n"); ++ goto err_unregister_chardev; ++ } ++ ++ /* ++ * Create sysfs entries ++ * 'bcm2708_vcio' is used for backwards compatibility so we don't break ++ * userspace. Raspian has a udev rule that changes the permissions. ++ */ ++ vcio.class = class_create(THIS_MODULE, "bcm2708_vcio"); ++ if (IS_ERR(vcio.class)) { ++ ret = PTR_ERR(vcio.class); ++ pr_err("failed to create class\n"); ++ goto err_cdev_del; ++ } ++ ++ dev = device_create(vcio.class, NULL, vcio.devt, NULL, "vcio"); ++ if (IS_ERR(dev)) { ++ ret = PTR_ERR(dev); ++ pr_err("failed to create device\n"); ++ goto err_class_destroy; ++ } ++ ++ return 0; ++ ++err_class_destroy: ++ class_destroy(vcio.class); ++err_cdev_del: ++ cdev_del(&vcio.cdev); ++err_unregister_chardev: ++ unregister_chrdev_region(vcio.devt, 1); ++ ++ return ret; ++} ++module_init(vcio_init); ++ ++static void __exit vcio_exit(void) ++{ ++ device_destroy(vcio.class, vcio.devt); ++ class_destroy(vcio.class); ++ cdev_del(&vcio.cdev); ++ unregister_chrdev_region(vcio.devt, 1); ++} ++module_exit(vcio_exit); ++ ++MODULE_AUTHOR("Gray Girling"); ++MODULE_AUTHOR("Noralf Trønnes"); ++MODULE_DESCRIPTION("Mailbox userspace access"); ++MODULE_LICENSE("GPL"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0053-firmware-bcm2835-Support-ARCH_BCM270x.patch b/target/linux/bcm27xx/patches-5.10/950-0053-firmware-bcm2835-Support-ARCH_BCM270x.patch new file mode 100644 index 0000000000..08d1e2af2d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0053-firmware-bcm2835-Support-ARCH_BCM270x.patch @@ -0,0 +1,83 @@ +From 410ae9727ad520a140b88c7151e0432d58516bc3 Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= +Date: Fri, 26 Jun 2015 14:25:01 +0200 +Subject: [PATCH] firmware: bcm2835: Support ARCH_BCM270x +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Support booting without Device Tree. +Turn on USB power. +Load driver early because of lacking support for deferred probing +in many drivers. + +Signed-off-by: Noralf Trønnes + +firmware: bcm2835: Don't turn on USB power + +The raspberrypi-power driver is now used to turn on USB power. + +This partly reverts commit: +firmware: bcm2835: Support ARCH_BCM270x + +Signed-off-by: Noralf Trønnes +--- + drivers/firmware/raspberrypi.c | 19 +++++++++++++++++-- + 1 file changed, 17 insertions(+), 2 deletions(-) + +--- a/drivers/firmware/raspberrypi.c ++++ b/drivers/firmware/raspberrypi.c +@@ -29,6 +29,8 @@ struct rpi_firmware { + u32 enabled; + }; + ++static struct platform_device *g_pdev; ++ + static DEFINE_MUTEX(transaction_lock); + + static void response_callback(struct mbox_client *cl, void *msg) +@@ -249,6 +251,7 @@ static int rpi_firmware_probe(struct pla + init_completion(&fw->c); + + platform_set_drvdata(pdev, fw); ++ g_pdev = pdev; + + rpi_firmware_print_firmware_revision(fw); + rpi_register_hwmon_driver(dev, fw); +@@ -276,6 +279,7 @@ static int rpi_firmware_remove(struct pl + platform_device_unregister(rpi_clk); + rpi_clk = NULL; + mbox_free_channel(fw->chan); ++ g_pdev = NULL; + + return 0; + } +@@ -288,7 +292,7 @@ static int rpi_firmware_remove(struct pl + */ + struct rpi_firmware *rpi_firmware_get(struct device_node *firmware_node) + { +- struct platform_device *pdev = of_find_device_by_node(firmware_node); ++ struct platform_device *pdev = g_pdev; + + if (!pdev) + return NULL; +@@ -312,7 +316,18 @@ static struct platform_driver rpi_firmwa + .shutdown = rpi_firmware_shutdown, + .remove = rpi_firmware_remove, + }; +-module_platform_driver(rpi_firmware_driver); ++ ++static int __init rpi_firmware_init(void) ++{ ++ return platform_driver_register(&rpi_firmware_driver); ++} ++subsys_initcall(rpi_firmware_init); ++ ++static void __init rpi_firmware_exit(void) ++{ ++ platform_driver_unregister(&rpi_firmware_driver); ++} ++module_exit(rpi_firmware_exit); + + MODULE_AUTHOR("Eric Anholt "); + MODULE_DESCRIPTION("Raspberry Pi firmware driver"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0054-BCM2708-Add-core-Device-Tree-support.patch b/target/linux/bcm27xx/patches-5.10/950-0054-BCM2708-Add-core-Device-Tree-support.patch new file mode 100644 index 0000000000..a103e04b38 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0054-BCM2708-Add-core-Device-Tree-support.patch @@ -0,0 +1,26485 @@ +From 81589b5e28022d0a4738981f9e5ffb9fadcfaa5b Mon Sep 17 00:00:00 2001 +From: notro +Date: Wed, 9 Jul 2014 14:46:08 +0200 +Subject: [PATCH] BCM2708: Add core Device Tree support +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +Add the bare minimum needed to boot BCM2708 from a Device Tree. + +Signed-off-by: Noralf Tronnes + +BCM2708: DT: change 'axi' nodename to 'soc' + +Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835. +The VC4 bootloader fills in certain properties in the 'axi' subtree, +but since this is part of an upstreaming effort, the name is changed. + +Signed-off-by: Noralf Tronnes notro@tronnes.org + +BCM2708_DT: Correct length of the peripheral space + +Use dts-dirs feature for overlays. + +The kernel makefiles have a dts-dirs target that is for vendor subdirectories. + +Using this fixes the install_dtbs target, which previously did not install the overlays. + +BCM270X_DT: configure I2S DMA channels + +Signed-off-by: Matthias Reichl + +BCM270X_DT: switch to bcm2835-i2s + +I2S soundcard drivers with proper devicetree support (i.e. not linking +to the cpu_dai/platform via name but to cpu/platform via of_node) +will work out of the box without any modifications. + +When the kernel is compiled without devicetree support the platform +code will instantiate the bcm2708-i2s driver and I2S soundcard drivers +will link to it via name, as before. + +Signed-off-by: Matthias Reichl + +SDIO-overlay: add poll_once-boolean parameter + +Add paramter to toggle sdio-device-polling +done every second or once at boot-time. + +Signed-off-by: Patrick Boettcher + +BCM270X_DT: Make mmc overlay compatible with current firmware + +The original DT overlay logic followed a merge-then-patch procedure, +i.e. parameters are applied to the loaded overlay before the overlay +is merged into the base DTB. This sequence has been changed to +patch-then-merge, in order to support parameterised node names, and +to protect against bad overlays. As a result, overrides (parameters) +must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB. + +mmc-overlay.dts (that switches back to the original mmc sdcard +driver) is the only overlay violating that rule, and this patch +fixes it. + +bcm270x_dt: Use the sdhost MMC controller by default + +The "mmc" overlay reverts to using the other controller. + +squash: Add cprman to dt + +BCM270X_DT: Use clk_core for I2C interfaces + +BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi + +The mainline Device Tree files are quite close to downstream now. +Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files +for our dts files. + +Mainline dts files are based on these files: + + bcm2835-rpi.dtsi + bcm2835.dtsi bcm2836.dtsi + bcm283x.dtsi + +Current downstream are based on these: + + bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi + bcm2708_common.dtsi + +This patch introduces this dependency: + + bcm2708.dtsi bcm2709.dtsi + bcm2708-rpi.dtsi + bcm270x.dtsi + bcm2835.dtsi bcm2836.dtsi + bcm283x.dtsi + +And: + bcm2710.dtsi + bcm2708-rpi.dtsi + bcm270x.dtsi + bcm283x.dtsi + +bcm270x.dtsi contains the downstream bcm283x.dtsi diff. +bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi. + +Other changes: +- The led node has moved from /soc/leds to /leds. This is not a problem + since the label is used to reference it. +- The clk_osc reg property changes from 6 to 3. +- The gpu nodes has their interrupt property set in the base file. +- the clocks label does not point to the /clocks node anymore, but + points to the cprman node. This is not a problem since the overlays + that use the clock node refer to it directly: target-path = "/clocks"; +- some nodes now have 2 labels since mainline and downstream differs in + this respect: cprman/clocks, spi0/spi, gpu/vc4. +- some nodes doesn't have an explicit status = "okay" since they're not + disabled in the base file: watchdog and random. +- gpiomem doesn't need an explicit status = "okay". +- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi, + it's now set directly in that file. +- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer. +- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes. + +Signed-off-by: Noralf Trønnes + +BCM270X_DT: Use raspberrypi-power to turn on USB power + +Use the raspberrypi-power driver to turn on USB power. + +Signed-off-by: Noralf Trønnes + +BCM270X_DT: Add a .dtbo target, use for overlays + +Change the filenames and extensions to keep the pre-DDT style of +overlay (-overlay.dtb) distinct from new ones that use a +different style of local fixups (.dtbo), and to match other +platforms. + +The RPi firmware uses the DDTK trailer atom to choose which type of +overlay to use for each kernel. + +Signed-off-by: Phil Elwell + +BCM270X_DT: Don't generate "linux,phandle" props + +The EPAPR standard says to use "phandle" properties to store phandles, +rather than the deprecated "linux,phandle" version. By default, dtc +generates both, but adding "-H epapr" causes it to only generate +"phandle"s, saving some space and clutter. + +Signed-off-by: Phil Elwell + +BCM270X_DT: Add overlay for enc28j60 on SPI2 + +Works on SPI2 for compute module + +BCM270X_DT: Add midi-uart0 overlay + +MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The +midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock +so that requesting 38.4kbaud actually gets 31.25kbaud. + +Signed-off-by: Phil Elwell + +BCM270X_DT: Add i2c-sensor overlay + +The i2c-sensor overlay is a container for various pressure and +temperature sensors, currently bmp085 and bmp280. The standalone +bmp085_i2c-sensor overlay is now deprecated. + +Signed-off-by: Phil Elwell + +BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752) + +We now create overlays as .dtbo files. + +build: support for .dtbo files for dtb overlays + +Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb. +Patch the kernel, which has faulty rules to generate .dtbo the way yocto does + +Signed-off-by: Herve Jourdain +Signed-off-by: Khem Raj + +BCM270X: Drop position requirement for CMA in VC4 overlay. + +No longer necessary since 2aefcd576195a739a7a256099571c9c4a401005f, +and will probably let peeople that want to choose a larger CMA +allocation (particularly on pi0/1). + +Signed-off-by: Eric Anholt + +BCM270X_DT: RPi Device Tree tidy + +Use the upstream sdhost node, add thermal-zones, and factor out some +common elements. + +Signed-off-by: Phil Elwell + +kbuild: Silence unhelpful DTC warnings + +Signed-off-by: Phil Elwell + +BCM270X_DT: DT build rules no longer arch-specific + +Signed-off-by: Phil Elwell +--- + .gitignore | 1 + + arch/arm/boot/dts/Makefile | 27 +- + arch/arm/boot/dts/bcm2708-rpi-b-plus.dts | 124 + + arch/arm/boot/dts/bcm2708-rpi-b-rev1.dts | 127 + + arch/arm/boot/dts/bcm2708-rpi-b.dts | 114 + + arch/arm/boot/dts/bcm2708-rpi-bt.dtsi | 26 + + arch/arm/boot/dts/bcm2708-rpi-cm.dts | 97 + + arch/arm/boot/dts/bcm2708-rpi-cm.dtsi | 18 + + arch/arm/boot/dts/bcm2708-rpi-zero-w.dts | 163 + + arch/arm/boot/dts/bcm2708-rpi-zero.dts | 117 + + arch/arm/boot/dts/bcm2708-rpi.dtsi | 36 + + arch/arm/boot/dts/bcm2708.dtsi | 12 + + arch/arm/boot/dts/bcm2709-rpi-2-b.dts | 124 + + arch/arm/boot/dts/bcm2709-rpi.dtsi | 5 + + arch/arm/boot/dts/bcm2709.dtsi | 22 + + arch/arm/boot/dts/bcm270x-rpi.dtsi | 154 + + arch/arm/boot/dts/bcm270x.dtsi | 197 ++ + arch/arm/boot/dts/bcm2710-rpi-2-b.dts | 124 + + arch/arm/boot/dts/bcm2710-rpi-3-b-plus.dts | 196 ++ + arch/arm/boot/dts/bcm2710-rpi-3-b.dts | 198 ++ + arch/arm/boot/dts/bcm2710-rpi-cm3.dts | 133 + + arch/arm/boot/dts/bcm2710.dtsi | 29 + + arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 306 +- + arch/arm/boot/dts/bcm2711-rpi-cm4.dts | 609 ++++ + arch/arm/boot/dts/bcm2711-rpi.dtsi | 201 ++ + arch/arm/boot/dts/bcm2711.dtsi | 34 +- + arch/arm/boot/dts/bcm271x-rpi-bt.dtsi | 26 + + arch/arm/boot/dts/bcm2835-common.dtsi | 4 +- + arch/arm/boot/dts/bcm2835-rpi-a-plus.dts | 5 + + arch/arm/boot/dts/bcm2835-rpi-a.dts | 7 + + arch/arm/boot/dts/bcm2835-rpi-b-plus.dts | 5 + + arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts | 7 + + arch/arm/boot/dts/bcm2835-rpi-b.dts | 7 + + arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts | 5 + + arch/arm/boot/dts/bcm2835-rpi-zero-w.dts | 5 + + arch/arm/boot/dts/bcm2835-rpi-zero.dts | 5 + + arch/arm/boot/dts/bcm2835-rpi.dtsi | 15 +- + arch/arm/boot/dts/bcm2835.dtsi | 2 +- + arch/arm/boot/dts/bcm2836-rpi-2-b.dts | 5 + + arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts | 5 + + arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts | 5 + + arch/arm/boot/dts/bcm2837-rpi-3-b.dts | 5 + + arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts | 5 + + arch/arm/boot/dts/bcm283x-rpi-csi0-2lane.dtsi | 4 + + arch/arm/boot/dts/bcm283x-rpi-csi1-2lane.dtsi | 4 + + arch/arm/boot/dts/bcm283x-rpi-csi1-4lane.dtsi | 4 + + .../boot/dts/bcm283x-rpi-i2c0mux_0_28.dtsi | 4 + + .../boot/dts/bcm283x-rpi-i2c0mux_0_44.dtsi | 4 + + .../boot/dts/bcm283x-rpi-usb-peripheral.dtsi | 7 - + arch/arm/boot/dts/bcm283x.dtsi | 26 +- + arch/arm/boot/dts/overlays/Makefile | 216 ++ + arch/arm/boot/dts/overlays/README | 3040 +++++++++++++++++ + .../arm/boot/dts/overlays/act-led-overlay.dts | 27 + + .../boot/dts/overlays/adafruit18-overlay.dts | 55 + + .../dts/overlays/adau1977-adc-overlay.dts | 40 + + .../dts/overlays/adau7002-simple-overlay.dts | 52 + + .../arm/boot/dts/overlays/ads1015-overlay.dts | 98 + + .../arm/boot/dts/overlays/ads1115-overlay.dts | 103 + + .../arm/boot/dts/overlays/ads7846-overlay.dts | 89 + + .../boot/dts/overlays/adv7282m-overlay.dts | 65 + + .../boot/dts/overlays/adv728x-m-overlay.dts | 37 + + .../overlays/akkordion-iqdacplus-overlay.dts | 49 + + .../allo-boss-dac-pcm512x-audio-overlay.dts | 59 + + .../dts/overlays/allo-digione-overlay.dts | 44 + + .../allo-katana-dac-audio-overlay.dts | 57 + + .../allo-piano-dac-pcm512x-audio-overlay.dts | 54 + + ...o-piano-dac-plus-pcm512x-audio-overlay.dts | 55 + + arch/arm/boot/dts/overlays/anyspi-overlay.dts | 205 ++ + .../boot/dts/overlays/apds9960-overlay.dts | 57 + + .../boot/dts/overlays/applepi-dac-overlay.dts | 57 + + .../boot/dts/overlays/at86rf233-overlay.dts | 57 + + .../overlays/audioinjector-addons-overlay.dts | 60 + + ...dioinjector-isolated-soundcard-overlay.dts | 55 + + .../overlays/audioinjector-ultra-overlay.dts | 71 + + .../audioinjector-wm8731-audio-overlay.dts | 39 + + .../dts/overlays/audiosense-pi-overlay.dts | 82 + + .../boot/dts/overlays/audremap-overlay.dts | 35 + + .../boot/dts/overlays/balena-fin-overlay.dts | 125 + + arch/arm/boot/dts/overlays/cma-overlay.dts | 36 + + arch/arm/boot/dts/overlays/dht11-overlay.dts | 41 + + .../dts/overlays/dionaudio-loco-overlay.dts | 39 + + .../overlays/dionaudio-loco-v2-overlay.dts | 49 + + .../boot/dts/overlays/disable-bt-overlay.dts | 64 + + .../dts/overlays/disable-wifi-overlay.dts | 20 + + arch/arm/boot/dts/overlays/dpi18-overlay.dts | 39 + + arch/arm/boot/dts/overlays/dpi24-overlay.dts | 39 + + arch/arm/boot/dts/overlays/draws-overlay.dts | 208 ++ + .../arm/boot/dts/overlays/dwc-otg-overlay.dts | 14 + + arch/arm/boot/dts/overlays/dwc2-overlay.dts | 26 + + .../boot/dts/overlays/enc28j60-overlay.dts | 53 + + .../dts/overlays/enc28j60-spi2-overlay.dts | 47 + + .../arm/boot/dts/overlays/exc3000-overlay.dts | 48 + + .../boot/dts/overlays/fe-pi-audio-overlay.dts | 70 + + .../boot/dts/overlays/fsm-demo-overlay.dts | 104 + + .../boot/dts/overlays/ghost-amp-overlay.dts | 119 + + arch/arm/boot/dts/overlays/goodix-overlay.dts | 46 + + .../googlevoicehat-soundcard-overlay.dts | 49 + + .../boot/dts/overlays/gpio-fan-overlay.dts | 79 + + .../arm/boot/dts/overlays/gpio-ir-overlay.dts | 49 + + .../boot/dts/overlays/gpio-ir-tx-overlay.dts | 36 + + .../boot/dts/overlays/gpio-key-overlay.dts | 48 + + .../overlays/gpio-no-bank0-irq-overlay.dts | 14 + + .../boot/dts/overlays/gpio-no-irq-overlay.dts | 14 + + .../dts/overlays/gpio-poweroff-overlay.dts | 37 + + .../dts/overlays/gpio-shutdown-overlay.dts | 84 + + .../boot/dts/overlays/hd44780-lcd-overlay.dts | 46 + + .../hdmi-backlight-hwhack-gpio-overlay.dts | 47 + + .../dts/overlays/hifiberry-amp-overlay.dts | 39 + + .../dts/overlays/hifiberry-dac-overlay.dts | 34 + + .../overlays/hifiberry-dacplus-overlay.dts | 65 + + .../overlays/hifiberry-dacplusadc-overlay.dts | 72 + + .../hifiberry-dacplusadcpro-overlay.dts | 65 + + .../overlays/hifiberry-dacplusdsp-overlay.dts | 34 + + .../overlays/hifiberry-dacplushd-overlay.dts | 106 + + .../dts/overlays/hifiberry-digi-overlay.dts | 41 + + .../overlays/hifiberry-digi-pro-overlay.dts | 43 + + .../boot/dts/overlays/highperi-overlay.dts | 63 + + arch/arm/boot/dts/overlays/hy28a-overlay.dts | 93 + + .../boot/dts/overlays/hy28b-2017-overlay.dts | 152 + + arch/arm/boot/dts/overlays/hy28b-overlay.dts | 148 + + .../boot/dts/overlays/i-sabre-q2m-overlay.dts | 39 + + .../boot/dts/overlays/i2c-bcm2708-overlay.dts | 13 + + .../boot/dts/overlays/i2c-gpio-overlay.dts | 47 + + .../arm/boot/dts/overlays/i2c-mux-overlay.dts | 139 + + .../dts/overlays/i2c-pwm-pca9685a-overlay.dts | 26 + + .../dts/overlays/i2c-rtc-gpio-overlay.dts | 266 ++ + .../arm/boot/dts/overlays/i2c-rtc-overlay.dts | 278 ++ + .../boot/dts/overlays/i2c-sensor-overlay.dts | 271 ++ + arch/arm/boot/dts/overlays/i2c0-overlay.dts | 74 + + arch/arm/boot/dts/overlays/i2c1-overlay.dts | 44 + + arch/arm/boot/dts/overlays/i2c3-overlay.dts | 36 + + arch/arm/boot/dts/overlays/i2c4-overlay.dts | 36 + + arch/arm/boot/dts/overlays/i2c5-overlay.dts | 36 + + arch/arm/boot/dts/overlays/i2c6-overlay.dts | 36 + + .../dts/overlays/i2s-gpio28-31-overlay.dts | 18 + + .../boot/dts/overlays/ilitek251x-overlay.dts | 45 + + arch/arm/boot/dts/overlays/imx219-overlay.dts | 119 + + arch/arm/boot/dts/overlays/imx290-overlay.dts | 32 + + .../boot/dts/overlays/imx290_327-overlay.dtsi | 145 + + arch/arm/boot/dts/overlays/imx477-overlay.dts | 119 + + .../dts/overlays/iqaudio-codec-overlay.dts | 42 + + .../boot/dts/overlays/iqaudio-dac-overlay.dts | 46 + + .../dts/overlays/iqaudio-dacplus-overlay.dts | 49 + + .../iqaudio-digi-wm8804-audio-overlay.dts | 47 + + .../arm/boot/dts/overlays/irs1125-overlay.dts | 85 + + .../dts/overlays/jedec-spi-nor-overlay.dts | 309 ++ + .../dts/overlays/justboom-both-overlay.dts | 65 + + .../dts/overlays/justboom-dac-overlay.dts | 46 + + .../dts/overlays/justboom-digi-overlay.dts | 41 + + .../arm/boot/dts/overlays/ltc294x-overlay.dts | 86 + + .../boot/dts/overlays/max98357a-overlay.dts | 84 + + .../boot/dts/overlays/maxtherm-overlay.dts | 166 + + .../boot/dts/overlays/mbed-dac-overlay.dts | 64 + + .../boot/dts/overlays/mcp23017-overlay.dts | 69 + + .../boot/dts/overlays/mcp23s17-overlay.dts | 732 ++++ + .../dts/overlays/mcp2515-can0-overlay.dts | 73 + + .../dts/overlays/mcp2515-can1-overlay.dts | 73 + + .../arm/boot/dts/overlays/mcp3008-overlay.dts | 205 ++ + .../arm/boot/dts/overlays/mcp3202-overlay.dts | 205 ++ + .../arm/boot/dts/overlays/mcp342x-overlay.dts | 164 + + .../dts/overlays/media-center-overlay.dts | 134 + + .../boot/dts/overlays/merus-amp-overlay.dts | 60 + + .../boot/dts/overlays/midi-uart0-overlay.dts | 36 + + .../boot/dts/overlays/midi-uart1-overlay.dts | 43 + + .../boot/dts/overlays/miniuart-bt-overlay.dts | 93 + + arch/arm/boot/dts/overlays/mmc-overlay.dts | 46 + + .../arm/boot/dts/overlays/mpu6050-overlay.dts | 28 + + .../arm/boot/dts/overlays/mz61581-overlay.dts | 117 + + arch/arm/boot/dts/overlays/ov5647-overlay.dts | 92 + + arch/arm/boot/dts/overlays/ov7251-overlay.dts | 111 + + arch/arm/boot/dts/overlays/ov9281-overlay.dts | 111 + + arch/arm/boot/dts/overlays/overlay_map.dts | 141 + + .../arm/boot/dts/overlays/papirus-overlay.dts | 89 + + .../arm/boot/dts/overlays/pca953x-overlay.dts | 240 ++ + arch/arm/boot/dts/overlays/pibell-overlay.dts | 81 + + .../dts/overlays/pifacedigital-overlay.dts | 144 + + arch/arm/boot/dts/overlays/piglow-overlay.dts | 97 + + .../boot/dts/overlays/piscreen-overlay.dts | 102 + + .../boot/dts/overlays/piscreen2r-overlay.dts | 106 + + .../arm/boot/dts/overlays/pisound-overlay.dts | 120 + + .../arm/boot/dts/overlays/pitft22-overlay.dts | 69 + + .../overlays/pitft28-capacitive-overlay.dts | 91 + + .../overlays/pitft28-resistive-overlay.dts | 119 + + .../overlays/pitft35-resistive-overlay.dts | 119 + + .../boot/dts/overlays/pps-gpio-overlay.dts | 38 + + .../boot/dts/overlays/pwm-2chan-overlay.dts | 49 + + .../boot/dts/overlays/pwm-ir-tx-overlay.dts | 40 + + arch/arm/boot/dts/overlays/pwm-overlay.dts | 45 + + .../arm/boot/dts/overlays/qca7000-overlay.dts | 55 + + .../dts/overlays/rotary-encoder-overlay.dts | 59 + + .../dts/overlays/rpi-backlight-overlay.dts | 21 + + .../overlays/rpi-cirrus-wm5102-overlay.dts | 172 + + .../arm/boot/dts/overlays/rpi-dac-overlay.dts | 34 + + .../boot/dts/overlays/rpi-display-overlay.dts | 91 + + .../boot/dts/overlays/rpi-ft5406-overlay.dts | 25 + + .../arm/boot/dts/overlays/rpi-poe-overlay.dts | 95 + + .../boot/dts/overlays/rpi-proto-overlay.dts | 39 + + .../boot/dts/overlays/rpi-sense-overlay.dts | 47 + + arch/arm/boot/dts/overlays/rpi-tv-overlay.dts | 34 + + .../boot/dts/overlays/rpivid-v4l2-overlay.dts | 61 + + .../rra-digidac1-wm8741-audio-overlay.dts | 49 + + .../boot/dts/overlays/sainsmart18-overlay.dts | 52 + + .../dts/overlays/sc16is750-i2c-overlay.dts | 43 + + .../dts/overlays/sc16is752-i2c-overlay.dts | 43 + + .../dts/overlays/sc16is752-spi0-overlay.dts | 49 + + .../dts/overlays/sc16is752-spi1-overlay.dts | 67 + + arch/arm/boot/dts/overlays/sdhost-overlay.dts | 38 + + arch/arm/boot/dts/overlays/sdio-overlay.dts | 77 + + .../arm/boot/dts/overlays/sdtweak-overlay.dts | 25 + + .../boot/dts/overlays/sh1106-spi-overlay.dts | 84 + + .../arm/boot/dts/overlays/smi-dev-overlay.dts | 20 + + .../boot/dts/overlays/smi-nand-overlay.dts | 66 + + arch/arm/boot/dts/overlays/smi-overlay.dts | 37 + + .../dts/overlays/spi-gpio35-39-overlay.dts | 31 + + .../dts/overlays/spi-gpio40-45-overlay.dts | 36 + + .../arm/boot/dts/overlays/spi-rtc-overlay.dts | 33 + + .../boot/dts/overlays/spi0-1cs-overlay.dts | 42 + + .../boot/dts/overlays/spi0-2cs-overlay.dts | 37 + + .../boot/dts/overlays/spi1-1cs-overlay.dts | 57 + + .../boot/dts/overlays/spi1-2cs-overlay.dts | 69 + + .../boot/dts/overlays/spi1-3cs-overlay.dts | 81 + + .../boot/dts/overlays/spi2-1cs-overlay.dts | 57 + + .../boot/dts/overlays/spi2-2cs-overlay.dts | 69 + + .../boot/dts/overlays/spi2-3cs-overlay.dts | 81 + + .../boot/dts/overlays/spi3-1cs-overlay.dts | 44 + + .../boot/dts/overlays/spi3-2cs-overlay.dts | 56 + + .../boot/dts/overlays/spi4-1cs-overlay.dts | 44 + + .../boot/dts/overlays/spi4-2cs-overlay.dts | 56 + + .../boot/dts/overlays/spi5-1cs-overlay.dts | 44 + + .../boot/dts/overlays/spi5-2cs-overlay.dts | 56 + + .../boot/dts/overlays/spi6-1cs-overlay.dts | 44 + + .../boot/dts/overlays/spi6-2cs-overlay.dts | 56 + + .../arm/boot/dts/overlays/ssd1306-overlay.dts | 36 + + .../boot/dts/overlays/ssd1306-spi-overlay.dts | 84 + + .../boot/dts/overlays/ssd1351-spi-overlay.dts | 83 + + .../dts/overlays/superaudioboard-overlay.dts | 73 + + arch/arm/boot/dts/overlays/sx150x-overlay.dts | 1706 +++++++++ + .../dts/overlays/tc358743-audio-overlay.dts | 52 + + .../boot/dts/overlays/tc358743-overlay.dts | 107 + + .../boot/dts/overlays/tinylcd35-overlay.dts | 222 ++ + .../boot/dts/overlays/tpm-slb9670-overlay.dts | 44 + + arch/arm/boot/dts/overlays/uart0-overlay.dts | 32 + + arch/arm/boot/dts/overlays/uart1-overlay.dts | 38 + + arch/arm/boot/dts/overlays/uart2-overlay.dts | 27 + + arch/arm/boot/dts/overlays/uart3-overlay.dts | 27 + + arch/arm/boot/dts/overlays/uart4-overlay.dts | 27 + + arch/arm/boot/dts/overlays/uart5-overlay.dts | 27 + + arch/arm/boot/dts/overlays/udrc-overlay.dts | 128 + + .../boot/dts/overlays/upstream-overlay.dts | 113 + + .../dts/overlays/upstream-pi4-overlay.dts | 161 + + .../dts/overlays/vc4-fkms-v3d-overlay.dts | 40 + + .../overlays/vc4-kms-kippah-7inch-overlay.dts | 43 + + .../boot/dts/overlays/vc4-kms-v3d-overlay.dts | 122 + + .../dts/overlays/vc4-kms-v3d-pi4-overlay.dts | 186 + + arch/arm/boot/dts/overlays/vga666-overlay.dts | 30 + + .../arm/boot/dts/overlays/w1-gpio-overlay.dts | 40 + + .../dts/overlays/w1-gpio-pullup-overlay.dts | 42 + + arch/arm/boot/dts/overlays/w5500-overlay.dts | 63 + + .../arm/boot/dts/overlays/wittypi-overlay.dts | 44 + + arch/arm64/boot/dts/Makefile | 2 + + arch/arm64/boot/dts/broadcom/Makefile | 16 +- + .../boot/dts/broadcom/bcm2710-rpi-2-b.dts | 3 + + .../dts/broadcom/bcm2710-rpi-3-b-plus.dts | 3 + + .../boot/dts/broadcom/bcm2710-rpi-3-b.dts | 3 + + .../boot/dts/broadcom/bcm2710-rpi-cm3.dts | 3 + + .../boot/dts/broadcom/bcm2711-rpi-4-b.dts | 5 +- + .../dts/broadcom/bcm283x-rpi-csi1-2lane.dtsi | 1 + + .../dts/broadcom/bcm283x-rpi-lan7515.dtsi | 1 + + arch/arm64/boot/dts/overlays | 1 + + scripts/Makefile.dtbinst | 6 +- + scripts/Makefile.lib | 13 + + 271 files changed, 23898 insertions(+), 31 deletions(-) + create mode 100644 arch/arm/boot/dts/bcm2708-rpi-b-plus.dts + create mode 100644 arch/arm/boot/dts/bcm2708-rpi-b-rev1.dts + create mode 100644 arch/arm/boot/dts/bcm2708-rpi-b.dts + create mode 100644 arch/arm/boot/dts/bcm2708-rpi-bt.dtsi + create mode 100644 arch/arm/boot/dts/bcm2708-rpi-cm.dts + create mode 100644 arch/arm/boot/dts/bcm2708-rpi-cm.dtsi + create mode 100644 arch/arm/boot/dts/bcm2708-rpi-zero-w.dts + create mode 100644 arch/arm/boot/dts/bcm2708-rpi-zero.dts + create mode 100644 arch/arm/boot/dts/bcm2708-rpi.dtsi + create mode 100644 arch/arm/boot/dts/bcm2708.dtsi + create mode 100644 arch/arm/boot/dts/bcm2709-rpi-2-b.dts + create mode 100644 arch/arm/boot/dts/bcm2709-rpi.dtsi + create mode 100644 arch/arm/boot/dts/bcm2709.dtsi + create mode 100644 arch/arm/boot/dts/bcm270x-rpi.dtsi + create mode 100644 arch/arm/boot/dts/bcm270x.dtsi + create mode 100644 arch/arm/boot/dts/bcm2710-rpi-2-b.dts + create mode 100644 arch/arm/boot/dts/bcm2710-rpi-3-b-plus.dts + create mode 100644 arch/arm/boot/dts/bcm2710-rpi-3-b.dts + create mode 100644 arch/arm/boot/dts/bcm2710-rpi-cm3.dts + create mode 100644 arch/arm/boot/dts/bcm2710.dtsi + create mode 100644 arch/arm/boot/dts/bcm2711-rpi-cm4.dts + create mode 100644 arch/arm/boot/dts/bcm2711-rpi.dtsi + create mode 100644 arch/arm/boot/dts/bcm271x-rpi-bt.dtsi + create mode 100644 arch/arm/boot/dts/bcm283x-rpi-csi0-2lane.dtsi + create mode 100644 arch/arm/boot/dts/bcm283x-rpi-csi1-2lane.dtsi + create mode 100644 arch/arm/boot/dts/bcm283x-rpi-csi1-4lane.dtsi + create mode 100644 arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_28.dtsi + create mode 100644 arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_44.dtsi + delete mode 100644 arch/arm/boot/dts/bcm283x-rpi-usb-peripheral.dtsi + create mode 100644 arch/arm/boot/dts/overlays/Makefile + create mode 100644 arch/arm/boot/dts/overlays/README + create mode 100644 arch/arm/boot/dts/overlays/act-led-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/adafruit18-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/adau1977-adc-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/adau7002-simple-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ads1015-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ads1115-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ads7846-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/adv7282m-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/adv728x-m-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/akkordion-iqdacplus-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/allo-boss-dac-pcm512x-audio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/allo-digione-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/allo-katana-dac-audio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/allo-piano-dac-pcm512x-audio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/allo-piano-dac-plus-pcm512x-audio-overlay.dts + create mode 100755 arch/arm/boot/dts/overlays/anyspi-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/apds9960-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/applepi-dac-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/at86rf233-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/audioinjector-addons-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/audioinjector-isolated-soundcard-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/audioinjector-ultra-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/audioinjector-wm8731-audio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/audiosense-pi-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/audremap-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/balena-fin-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/cma-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/dht11-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/dionaudio-loco-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/dionaudio-loco-v2-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/disable-bt-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/disable-wifi-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/dpi18-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/dpi24-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/draws-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/dwc-otg-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/dwc2-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/enc28j60-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/enc28j60-spi2-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/exc3000-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/fe-pi-audio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/fsm-demo-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ghost-amp-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/goodix-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/googlevoicehat-soundcard-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/gpio-fan-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/gpio-ir-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/gpio-ir-tx-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/gpio-key-overlay.dts + create mode 100755 arch/arm/boot/dts/overlays/gpio-no-bank0-irq-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/gpio-no-irq-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/gpio-poweroff-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/gpio-shutdown-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hd44780-lcd-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hdmi-backlight-hwhack-gpio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-dacplusadc-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-dacplusadcpro-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-dacplusdsp-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-dacplushd-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hifiberry-digi-pro-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/highperi-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hy28a-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hy28b-2017-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/hy28b-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i-sabre-q2m-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c-bcm2708-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c-mux-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c-pwm-pca9685a-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c-rtc-gpio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c-sensor-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c0-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c1-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c3-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c4-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c5-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2c6-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/i2s-gpio28-31-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ilitek251x-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/imx219-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/imx290-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/imx290_327-overlay.dtsi + create mode 100644 arch/arm/boot/dts/overlays/imx477-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/iqaudio-codec-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/iqaudio-digi-wm8804-audio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/irs1125-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/jedec-spi-nor-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/justboom-both-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/justboom-dac-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/justboom-digi-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ltc294x-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/max98357a-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/maxtherm-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/mbed-dac-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/mcp23017-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/mcp23s17-overlay.dts + create mode 100755 arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/mcp2515-can1-overlay.dts + create mode 100755 arch/arm/boot/dts/overlays/mcp3008-overlay.dts + create mode 100755 arch/arm/boot/dts/overlays/mcp3202-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/mcp342x-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/media-center-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/merus-amp-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/midi-uart0-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/midi-uart1-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/miniuart-bt-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/mmc-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/mpu6050-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/mz61581-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ov5647-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ov7251-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ov9281-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/overlay_map.dts + create mode 100644 arch/arm/boot/dts/overlays/papirus-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pca953x-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pibell-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pifacedigital-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/piglow-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/piscreen-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/piscreen2r-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pisound-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pitft22-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pitft28-capacitive-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pitft35-resistive-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pps-gpio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pwm-ir-tx-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/pwm-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/qca7000-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rotary-encoder-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-backlight-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-cirrus-wm5102-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-dac-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-display-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-ft5406-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-poe-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-proto-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-sense-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpi-tv-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rpivid-v4l2-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/rra-digidac1-wm8741-audio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sainsmart18-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sc16is750-i2c-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sc16is752-i2c-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sc16is752-spi0-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sc16is752-spi1-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sdhost-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sdio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sdtweak-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sh1106-spi-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/smi-dev-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/smi-nand-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/smi-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi-gpio35-39-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi-gpio40-45-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi-rtc-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi0-1cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi0-2cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi1-1cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi1-2cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi1-3cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi2-1cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi2-2cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi2-3cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi3-1cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi3-2cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi4-1cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi4-2cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi5-1cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi5-2cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi6-1cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/spi6-2cs-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ssd1306-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ssd1306-spi-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/ssd1351-spi-overlay.dts + create mode 100755 arch/arm/boot/dts/overlays/superaudioboard-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/sx150x-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/tc358743-audio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/tc358743-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/tinylcd35-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/tpm-slb9670-overlay.dts + create mode 100755 arch/arm/boot/dts/overlays/uart0-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/uart1-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/uart2-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/uart3-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/uart4-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/uart5-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/udrc-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/upstream-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/upstream-pi4-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/vc4-fkms-v3d-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/vc4-kms-kippah-7inch-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/vc4-kms-v3d-pi4-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/vga666-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/w1-gpio-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/w1-gpio-pullup-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/w5500-overlay.dts + create mode 100644 arch/arm/boot/dts/overlays/wittypi-overlay.dts + create mode 100644 arch/arm64/boot/dts/broadcom/bcm2710-rpi-2-b.dts + create mode 100644 arch/arm64/boot/dts/broadcom/bcm2710-rpi-3-b-plus.dts + create mode 100644 arch/arm64/boot/dts/broadcom/bcm2710-rpi-3-b.dts + create mode 100644 arch/arm64/boot/dts/broadcom/bcm2710-rpi-cm3.dts + create mode 120000 arch/arm64/boot/dts/broadcom/bcm283x-rpi-csi1-2lane.dtsi + create mode 120000 arch/arm64/boot/dts/broadcom/bcm283x-rpi-lan7515.dtsi + create mode 120000 arch/arm64/boot/dts/overlays + +diff --git a/.gitignore b/.gitignore +index 67d2f3503128..8b0b16eeca88 100644 +--- a/.gitignore ++++ b/.gitignore +@@ -18,6 +18,7 @@ + *.c.[012]*.* + *.dt.yaml + *.dtb ++*.dtbo + *.dtb.S + *.dwo + *.elf +diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile +index ce66ffd5a1bb..87241fe26e10 100644 +--- a/arch/arm/boot/dts/Makefile ++++ b/arch/arm/boot/dts/Makefile +@@ -1,4 +1,20 @@ + # SPDX-License-Identifier: GPL-2.0 ++ ++dtb-$(CONFIG_ARCH_BCM2835) += \ ++ bcm2708-rpi-b.dtb \ ++ bcm2708-rpi-b-rev1.dtb \ ++ bcm2708-rpi-b-plus.dtb \ ++ bcm2708-rpi-cm.dtb \ ++ bcm2708-rpi-zero.dtb \ ++ bcm2708-rpi-zero-w.dtb \ ++ bcm2709-rpi-2-b.dtb \ ++ bcm2710-rpi-2-b.dtb \ ++ bcm2710-rpi-3-b.dtb \ ++ bcm2711-rpi-4-b.dtb \ ++ bcm2710-rpi-3-b-plus.dtb \ ++ bcm2710-rpi-cm3.dtb \ ++ bcm2711-rpi-cm4.dtb ++ + dtb-$(CONFIG_ARCH_ALPINE) += \ + alpine-db.dtb + dtb-$(CONFIG_MACH_ARTPEC6) += \ +@@ -92,7 +108,6 @@ dtb-$(CONFIG_ARCH_BCM2835) += \ + bcm2837-rpi-3-b.dtb \ + bcm2837-rpi-3-b-plus.dtb \ + bcm2837-rpi-cm3-io3.dtb \ +- bcm2711-rpi-4-b.dtb \ + bcm2835-rpi-zero.dtb \ + bcm2835-rpi-zero-w.dtb + dtb-$(CONFIG_ARCH_BCM_5301X) += \ +@@ -1408,3 +1423,13 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ + aspeed-bmc-opp-zaius.dtb \ + aspeed-bmc-portwell-neptune.dtb \ + aspeed-bmc-quanta-q71l.dtb ++ ++targets += dtbs dtbs_install ++targets += $(dtb-y) ++ ++subdir-y := overlays ++ ++# Enable fixups to support overlays on BCM2835 platforms ++ifeq ($(CONFIG_ARCH_BCM2835),y) ++ DTC_FLAGS ?= -@ ++endif +diff --git a/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts b/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts +new file mode 100644 +index 000000000000..98581eec4bdc +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi-b-plus.dts +@@ -0,0 +1,124 @@ ++/dts-v1/; ++ ++#include "bcm2708.dtsi" ++#include "bcm2708-rpi.dtsi" ++#include "bcm283x-rpi-smsc9514.dtsi" ++#include "bcm283x-rpi-csi1-2lane.dtsi" ++#include "bcm283x-rpi-i2c0mux_0_28.dtsi" ++ ++/ { ++ compatible = "raspberrypi,model-b-plus", "brcm,bcm2835"; ++ model = "Raspberry Pi Model B+"; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins = <40 45>; ++ brcm,function = <4>; ++ }; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++}; ++ ++&i2c0if { ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&gpio 47 0>; ++ }; ++ ++ pwr_led: pwr { ++ label = "led1"; ++ linux,default-trigger = "input"; ++ gpios = <&gpio 35 0>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ ++ pwr_led_gpio = <&pwr_led>,"gpios:4"; ++ pwr_led_activelow = <&pwr_led>,"gpios:8"; ++ pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2708-rpi-b-rev1.dts b/arch/arm/boot/dts/bcm2708-rpi-b-rev1.dts +new file mode 100644 +index 000000000000..7b554b465b27 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi-b-rev1.dts +@@ -0,0 +1,127 @@ ++/dts-v1/; ++ ++#include "bcm2708.dtsi" ++#include "bcm2708-rpi.dtsi" ++#include "bcm283x-rpi-smsc9512.dtsi" ++#include "bcm283x-rpi-csi1-2lane.dtsi" ++ ++/ { ++ compatible = "raspberrypi,model-b", "brcm,bcm2835"; ++ model = "Raspberry Pi Model B"; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <28 29 30 31>; ++ brcm,function = <6>; /* alt2 */ ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins = <40 45>; ++ brcm,function = <4>; ++ }; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++}; ++ ++/delete-node/ &i2c0mux; ++ ++i2c0: &i2c0if { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c0_pins>; ++ clock-frequency = <100000>; ++}; ++ ++i2c_csi_dsi: &i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++/ { ++ aliases { ++ i2c0 = &i2c0; ++ }; ++ ++ __overrides__ { ++ i2c0 = <&i2c0>, "status"; ++ }; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&gpio 16 1>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2708-rpi-b.dts b/arch/arm/boot/dts/bcm2708-rpi-b.dts +new file mode 100644 +index 000000000000..305f1dbde60f +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi-b.dts +@@ -0,0 +1,114 @@ ++/dts-v1/; ++ ++#include "bcm2708.dtsi" ++#include "bcm2708-rpi.dtsi" ++#include "bcm283x-rpi-smsc9512.dtsi" ++#include "bcm283x-rpi-csi1-2lane.dtsi" ++#include "bcm283x-rpi-i2c0mux_0_28.dtsi" ++ ++/ { ++ compatible = "raspberrypi,model-b", "brcm,bcm2835"; ++ model = "Raspberry Pi Model B"; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <28 29 30 31>; ++ brcm,function = <6>; /* alt2 */ ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins = <40 45>; ++ brcm,function = <4>; ++ }; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++}; ++ ++&i2c0if { ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&gpio 16 1>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2708-rpi-bt.dtsi b/arch/arm/boot/dts/bcm2708-rpi-bt.dtsi +new file mode 100644 +index 000000000000..a18f80af97d3 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi-bt.dtsi +@@ -0,0 +1,26 @@ ++// SPDX-License-Identifier: GPL-2.0 ++ ++&uart0 { ++ bt: bluetooth { ++ compatible = "brcm,bcm43438-bt"; ++ max-speed = <3000000>; ++ shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>; ++ status = "disabled"; ++ }; ++}; ++ ++&uart1 { ++ minibt: bluetooth { ++ compatible = "brcm,bcm43438-bt"; ++ max-speed = <460800>; ++ shutdown-gpios = <&gpio 45 GPIO_ACTIVE_HIGH>; ++ status = "disabled"; ++ }; ++}; ++ ++/ { ++ __overrides__ { ++ krnbt = <&bt>,"status"; ++ krnbt_baudrate = <&bt>,"max-speed:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2708-rpi-cm.dts b/arch/arm/boot/dts/bcm2708-rpi-cm.dts +new file mode 100644 +index 000000000000..93062c4ffad2 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dts +@@ -0,0 +1,97 @@ ++/dts-v1/; ++ ++#include "bcm2708-rpi-cm.dtsi" ++#include "bcm283x-rpi-csi0-2lane.dtsi" ++#include "bcm283x-rpi-csi1-4lane.dtsi" ++#include "bcm283x-rpi-i2c0mux_0_28.dtsi" ++ ++/ { ++ compatible = "raspberrypi,compute-module", "brcm,bcm2835"; ++ model = "Raspberry Pi Compute Module"; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins; ++ brcm,function; ++ }; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++}; ++ ++&i2c0if { ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>; ++}; +diff --git a/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi b/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi +new file mode 100644 +index 000000000000..dce160f420fd +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi-cm.dtsi +@@ -0,0 +1,18 @@ ++#include "bcm2708.dtsi" ++#include "bcm2708-rpi.dtsi" ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&gpio 47 0>; ++ }; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2708-rpi-zero-w.dts b/arch/arm/boot/dts/bcm2708-rpi-zero-w.dts +new file mode 100644 +index 000000000000..f1bbed9fbf73 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi-zero-w.dts +@@ -0,0 +1,163 @@ ++/dts-v1/; ++ ++#include "bcm2708.dtsi" ++#include "bcm2708-rpi.dtsi" ++#include "bcm283x-rpi-csi1-2lane.dtsi" ++#include "bcm283x-rpi-i2c0mux_0_28.dtsi" ++#include "bcm2708-rpi-bt.dtsi" ++ ++/ { ++ compatible = "raspberrypi,model-zero-w", "brcm,bcm2835"; ++ model = "Raspberry Pi Zero W"; ++ ++ chosen { ++ bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1"; ++ }; ++ ++ aliases { ++ serial0 = &uart1; ++ serial1 = &uart0; ++ mmc1 = &mmcnr; ++ }; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ sdio_pins: sdio_pins { ++ brcm,pins = <34 35 36 37 38 39>; ++ brcm,function = <7>; /* ALT3 = SD1 */ ++ brcm,pull = <0 2 2 2 2 2>; ++ }; ++ ++ bt_pins: bt_pins { ++ brcm,pins = <43>; ++ brcm,function = <4>; /* alt0:GPCLK2 */ ++ brcm,pull = <0>; /* none */ ++ }; ++ ++ uart0_pins: uart0_pins { ++ brcm,pins = <30 31 32 33>; ++ brcm,function = <7>; /* alt3=UART0 */ ++ brcm,pull = <2 0 0 2>; /* up none none up */ ++ }; ++ ++ uart1_pins: uart1_pins { ++ brcm,pins; ++ brcm,function; ++ brcm,pull; ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins = <>; ++ brcm,function = <>; ++ }; ++}; ++ ++&mmcnr { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdio_pins>; ++ bus-width = <4>; ++ status = "okay"; ++}; ++ ++&uart0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_pins &bt_pins>; ++ status = "okay"; ++}; ++ ++&uart1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart1_pins>; ++ status = "okay"; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++}; ++ ++&i2c0if { ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "actpwr"; ++ gpios = <&gpio 47 GPIO_ACTIVE_LOW>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2708-rpi-zero.dts b/arch/arm/boot/dts/bcm2708-rpi-zero.dts +new file mode 100644 +index 000000000000..e7578788b839 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi-zero.dts +@@ -0,0 +1,117 @@ ++/dts-v1/; ++ ++#include "bcm2708.dtsi" ++#include "bcm2708-rpi.dtsi" ++#include "bcm283x-rpi-csi1-2lane.dtsi" ++#include "bcm283x-rpi-i2c0mux_0_28.dtsi" ++ ++/ { ++ compatible = "raspberrypi,model-zero", "brcm,bcm2835"; ++ model = "Raspberry Pi Zero"; ++ ++ chosen { ++ bootargs = "coherent_pool=1M snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1"; ++ }; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins = <>; ++ brcm,function = <>; ++ }; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++}; ++ ++&i2c0if { ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "actpwr"; ++ gpios = <&gpio 47 GPIO_ACTIVE_LOW>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2708-rpi.dtsi b/arch/arm/boot/dts/bcm2708-rpi.dtsi +new file mode 100644 +index 000000000000..e2458b15d64a +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708-rpi.dtsi +@@ -0,0 +1,36 @@ ++/* Downstream modifications common to bcm2835, bcm2836, bcm2837 */ ++ ++#include "bcm2835-rpi.dtsi" ++#include "bcm270x-rpi.dtsi" ++ ++/ { ++ memory@0 { ++ device_type = "memory"; ++ reg = <0x0 0x0>; ++ }; ++ ++ aliases { ++ i2c2 = &i2c2; ++ }; ++ ++ __overrides__ { ++ i2c2_iknowwhatimdoing = <&i2c2>,"status"; ++ i2c2_baudrate = <&i2c2>,"clock-frequency:0"; ++ sd_poll_once = <&sdhost>,"non-removable?"; ++ }; ++}; ++ ++&sdhost { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdhost_gpio48>; ++ status = "okay"; ++}; ++ ++&hdmi { ++ power-domains = <&power RPI_POWER_DOMAIN_HDMI>; ++ status = "disabled"; ++}; ++ ++&i2c2 { ++ status = "disabled"; ++}; +diff --git a/arch/arm/boot/dts/bcm2708.dtsi b/arch/arm/boot/dts/bcm2708.dtsi +new file mode 100644 +index 000000000000..36ec4989403f +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2708.dtsi +@@ -0,0 +1,12 @@ ++#include "bcm2835.dtsi" ++#include "bcm270x.dtsi" ++ ++/ { ++ __overrides__ { ++ arm_freq; ++ }; ++}; ++ ++&vc4 { ++ status = "disabled"; ++}; +diff --git a/arch/arm/boot/dts/bcm2709-rpi-2-b.dts b/arch/arm/boot/dts/bcm2709-rpi-2-b.dts +new file mode 100644 +index 000000000000..6b2e3c291d72 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2709-rpi-2-b.dts +@@ -0,0 +1,124 @@ ++/dts-v1/; ++ ++#include "bcm2709.dtsi" ++#include "bcm2709-rpi.dtsi" ++#include "bcm283x-rpi-smsc9514.dtsi" ++#include "bcm283x-rpi-csi1-2lane.dtsi" ++#include "bcm283x-rpi-i2c0mux_0_28.dtsi" ++ ++/ { ++ compatible = "raspberrypi,2-model-b", "brcm,bcm2836"; ++ model = "Raspberry Pi 2 Model B"; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins = <40 45>; ++ brcm,function = <4>; ++ }; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++}; ++ ++&i2c0if { ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&gpio 47 0>; ++ }; ++ ++ pwr_led: pwr { ++ label = "led1"; ++ linux,default-trigger = "input"; ++ gpios = <&gpio 35 0>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ ++ pwr_led_gpio = <&pwr_led>,"gpios:4"; ++ pwr_led_activelow = <&pwr_led>,"gpios:8"; ++ pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2709-rpi.dtsi b/arch/arm/boot/dts/bcm2709-rpi.dtsi +new file mode 100644 +index 000000000000..babfa41cd9f7 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2709-rpi.dtsi +@@ -0,0 +1,5 @@ ++#include "bcm2708-rpi.dtsi" ++ ++&vchiq { ++ compatible = "brcm,bcm2836-vchiq", "brcm,bcm2835-vchiq"; ++}; +diff --git a/arch/arm/boot/dts/bcm2709.dtsi b/arch/arm/boot/dts/bcm2709.dtsi +new file mode 100644 +index 000000000000..68eafc1b281a +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2709.dtsi +@@ -0,0 +1,22 @@ ++#include "bcm2836.dtsi" ++#include "bcm270x.dtsi" ++ ++/ { ++ soc { ++ ranges = <0x7e000000 0x3f000000 0x01000000>, ++ <0x40000000 0x40000000 0x00040000>; ++ ++ /delete-node/ timer@7e003000; ++ }; ++ ++ __overrides__ { ++ arm_freq = <&v7_cpu0>, "clock-frequency:0", ++ <&v7_cpu1>, "clock-frequency:0", ++ <&v7_cpu2>, "clock-frequency:0", ++ <&v7_cpu3>, "clock-frequency:0"; ++ }; ++}; ++ ++&vc4 { ++ status = "disabled"; ++}; +diff --git a/arch/arm/boot/dts/bcm270x-rpi.dtsi b/arch/arm/boot/dts/bcm270x-rpi.dtsi +new file mode 100644 +index 000000000000..68a7e1c09db1 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm270x-rpi.dtsi +@@ -0,0 +1,154 @@ ++/* Downstream modifications to bcm2835-rpi.dtsi */ ++ ++/ { ++ aliases { ++ audio = &audio; ++ aux = &aux; ++ sound = &sound; ++ soc = &soc; ++ dma = &dma; ++ intc = &intc; ++ watchdog = &watchdog; ++ random = &random; ++ mailbox = &mailbox; ++ gpio = &gpio; ++ uart0 = &uart0; ++ uart1 = &uart1; ++ sdhost = &sdhost; ++ mmc = &mmc; ++ mmc1 = &mmc; ++ mmc0 = &sdhost; ++ i2s = &i2s; ++ i2c0 = &i2c0; ++ i2c1 = &i2c1; ++ i2c10 = &i2c_csi_dsi; ++ spi0 = &spi0; ++ spi1 = &spi1; ++ spi2 = &spi2; ++ usb = &usb; ++ leds = &leds; ++ fb = &fb; ++ thermal = &thermal; ++ axiperf = &axiperf; ++ }; ++ ++ /* Define these notional regulators for use by overlays */ ++ vdd_3v3_reg: fixedregulator_3v3 { ++ compatible = "regulator-fixed"; ++ regulator-always-on; ++ regulator-max-microvolt = <3300000>; ++ regulator-min-microvolt = <3300000>; ++ regulator-name = "3v3"; ++ }; ++ ++ vdd_5v0_reg: fixedregulator_5v0 { ++ compatible = "regulator-fixed"; ++ regulator-always-on; ++ regulator-max-microvolt = <5000000>; ++ regulator-min-microvolt = <5000000>; ++ regulator-name = "5v0"; ++ }; ++ ++ leds: leds { ++ compatible = "gpio-leds"; ++ }; ++ ++ soc { ++ gpiomem { ++ compatible = "brcm,bcm2835-gpiomem"; ++ reg = <0x7e200000 0x1000>; ++ }; ++ ++ fb: fb { ++ compatible = "brcm,bcm2708-fb"; ++ firmware = <&firmware>; ++ status = "okay"; ++ }; ++ ++ vcsm: vcsm { ++ compatible = "raspberrypi,bcm2835-vcsm"; ++ firmware = <&firmware>; ++ status = "okay"; ++ }; ++ ++ /* External sound card */ ++ sound: sound { ++ status = "disabled"; ++ }; ++ }; ++ ++ __overrides__ { ++ cache_line_size; ++ ++ uart0 = <&uart0>,"status"; ++ uart1 = <&uart1>,"status"; ++ i2s = <&i2s>,"status"; ++ spi = <&spi0>,"status"; ++ i2c0 = <&i2c0if>,"status",<&i2c0mux>,"status"; ++ i2c1 = <&i2c1>,"status"; ++ i2c0_baudrate = <&i2c0if>,"clock-frequency:0"; ++ i2c1_baudrate = <&i2c1>,"clock-frequency:0"; ++ ++ audio = <&audio>,"status"; ++ watchdog = <&watchdog>,"status"; ++ random = <&random>,"status"; ++ sd_overclock = <&sdhost>,"brcm,overclock-50:0"; ++ sd_force_pio = <&sdhost>,"brcm,force-pio?"; ++ sd_pio_limit = <&sdhost>,"brcm,pio-limit:0"; ++ sd_debug = <&sdhost>,"brcm,debug"; ++ sdio_overclock = <&mmc>,"brcm,overclock-50:0", ++ <&mmcnr>,"brcm,overclock-50:0"; ++ axiperf = <&axiperf>,"status"; ++ }; ++}; ++ ++&uart0 { ++ skip-init; ++}; ++ ++&uart1 { ++ skip-init; ++}; ++ ++&txp { ++ status = "disabled"; ++}; ++ ++&i2c0if { ++ status = "disabled"; ++}; ++ ++&i2c0mux { ++ status = "disabled"; ++}; ++ ++&i2c1 { ++ status = "disabled"; ++}; ++ ++&clocks { ++ firmware = <&firmware>; ++}; ++ ++&sdhci { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&emmc_gpio48>; ++ bus-width = <4>; ++}; ++ ++&cpu_thermal { ++ /delete-node/ trips; ++}; ++ ++&vec { ++ status = "disabled"; ++}; ++ ++&vchiq { ++ /* Onboard audio */ ++ audio: bcm2835_audio { ++ compatible = "brcm,bcm2835-audio"; ++ brcm,pwm-channels = <8>; ++ status = "disabled"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm270x.dtsi b/arch/arm/boot/dts/bcm270x.dtsi +new file mode 100644 +index 000000000000..446d4ff64842 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm270x.dtsi +@@ -0,0 +1,197 @@ ++/* Downstream bcm283x.dtsi diff */ ++#include ++ ++/ { ++ chosen { ++ bootargs = "coherent_pool=1M snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1"; ++ /delete-property/ stdout-path; ++ }; ++ ++ soc: soc { ++ ++ watchdog: watchdog@7e100000 { ++ /* Add label */ ++ }; ++ ++ random: rng@7e104000 { ++ /* Add label */ ++ }; ++ ++ spi0: spi@7e204000 { ++ /* Add label */ ++ }; ++ ++#ifndef BCM2711 ++ pixelvalve0: pixelvalve@7e206000 { ++ /* Add label */ ++ status = "disabled"; ++ }; ++ ++ pixelvalve1: pixelvalve@7e207000 { ++ /* Add label */ ++ status = "disabled"; ++ }; ++#endif ++ ++ /delete-node/ sdhci@7e300000; ++ ++ sdhci: mmc: mmc@7e300000 { ++ compatible = "brcm,bcm2835-mmc", "brcm,bcm2835-sdhci"; ++ reg = <0x7e300000 0x100>; ++ interrupts = <2 30>; ++ clocks = <&clocks BCM2835_CLOCK_EMMC>; ++ dmas = <&dma 11>; ++ dma-names = "rx-tx"; ++ brcm,overclock-50 = <0>; ++ status = "disabled"; ++ }; ++ ++ /* A clone of mmc but with non-removable set */ ++ mmcnr: mmcnr@7e300000 { ++ compatible = "brcm,bcm2835-mmc", "brcm,bcm2835-sdhci"; ++ reg = <0x7e300000 0x100>; ++ interrupts = <2 30>; ++ clocks = <&clocks BCM2835_CLOCK_EMMC>; ++ dmas = <&dma 11>; ++ dma-names = "rx-tx"; ++ brcm,overclock-50 = <0>; ++ non-removable; ++ status = "disabled"; ++ }; ++ ++ hvs: hvs@7e400000 { ++ /* Add label */ ++ status = "disabled"; ++ }; ++ ++ firmwarekms: firmwarekms@7e600000 { ++ compatible = "raspberrypi,rpi-firmware-kms"; ++ /* SMI interrupt reg */ ++ reg = <0x7e600000 0x100>; ++ interrupts = <2 16>; ++ brcm,firmware = <&firmware>; ++ status = "disabled"; ++ }; ++ ++ smi: smi@7e600000 { ++ compatible = "brcm,bcm2835-smi"; ++ reg = <0x7e600000 0x100>; ++ interrupts = <2 16>; ++ clocks = <&clocks BCM2835_CLOCK_SMI>; ++ assigned-clocks = <&clocks BCM2835_CLOCK_SMI>; ++ assigned-clock-rates = <125000000>; ++ dmas = <&dma 4>; ++ dma-names = "rx-tx"; ++ status = "disabled"; ++ }; ++ ++ csi0: csi@7e800000 { ++ compatible = "brcm,bcm2835-unicam"; ++ reg = <0x7e800000 0x800>, ++ <0x7e802000 0x4>; ++ interrupts = <2 6>; ++ clocks = <&clocks BCM2835_CLOCK_CAM0>, ++ <&firmware_clocks 4>; ++ clock-names = "lp", "vpu"; ++ power-domains = <&power RPI_POWER_DOMAIN_UNICAM0>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ #clock-cells = <1>; ++ status = "disabled"; ++ }; ++ ++ csi1: csi@7e801000 { ++ compatible = "brcm,bcm2835-unicam"; ++ reg = <0x7e801000 0x800>, ++ <0x7e802004 0x4>; ++ interrupts = <2 7>; ++ clocks = <&clocks BCM2835_CLOCK_CAM1>, ++ <&firmware_clocks 4>; ++ clock-names = "lp", "vpu"; ++ power-domains = <&power RPI_POWER_DOMAIN_UNICAM1>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ #clock-cells = <1>; ++ status = "disabled"; ++ }; ++ ++#ifndef BCM2711 ++ pixelvalve2: pixelvalve@7e807000 { ++ /* Add label */ ++ status = "disabled"; ++ }; ++#endif ++ ++ hdmi@7e902000 { /* hdmi */ ++ status = "disabled"; ++ }; ++ ++ usb@7e980000 { /* usb */ ++ compatible = "brcm,bcm2708-usb"; ++ reg = <0x7e980000 0x10000>, ++ <0x7e006000 0x1000>; ++ interrupt-names = "usb", ++ "soft"; ++ interrupts = <1 9>, ++ <2 0>; ++ }; ++ ++#ifndef BCM2711 ++ v3d@7ec00000 { /* vd3 */ ++ compatible = "brcm,vc4-v3d"; ++ power-domains = <&power RPI_POWER_DOMAIN_V3D>; ++ status = "disabled"; ++ }; ++#endif ++ ++ axiperf: axiperf { ++ compatible = "brcm,bcm2835-axiperf"; ++ reg = <0x7e009800 0x100>, ++ <0x7ee08000 0x100>; ++ firmware = <&firmware>; ++ status = "disabled"; ++ }; ++ }; ++ ++ __overrides__ { ++ cam0-pwdn-ctrl; ++ cam0-pwdn; ++ cam0-led-ctrl; ++ cam0-led; ++ }; ++}; ++ ++&gpio { ++ interrupts = <2 17>, <2 18>; ++ ++ dpi_18bit_gpio0: dpi_18bit_gpio0 { ++ brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11 ++ 12 13 14 15 16 17 18 19 ++ 20 21>; ++ brcm,function = ; ++ }; ++}; ++ ++&uart0 { ++ /* Enable CTS bug workaround */ ++ cts-event-workaround; ++}; ++ ++&i2s { ++ #sound-dai-cells = <0>; ++ dmas = <&dma 2>, <&dma 3>; ++ dma-names = "tx", "rx"; ++}; ++ ++&sdhost { ++ dmas = <&dma (13|(1<<29))>; ++ dma-names = "rx-tx"; ++ bus-width = <4>; ++ brcm,overclock-50 = <0>; ++ brcm,pio-limit = <1>; ++}; ++ ++&spi0 { ++ dmas = <&dma 6>, <&dma 7>; ++ dma-names = "tx", "rx"; ++}; +diff --git a/arch/arm/boot/dts/bcm2710-rpi-2-b.dts b/arch/arm/boot/dts/bcm2710-rpi-2-b.dts +new file mode 100644 +index 000000000000..49cfda63606e +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2710-rpi-2-b.dts +@@ -0,0 +1,124 @@ ++/dts-v1/; ++ ++#include "bcm2710.dtsi" ++#include "bcm2709-rpi.dtsi" ++#include "bcm283x-rpi-smsc9514.dtsi" ++#include "bcm283x-rpi-csi1-2lane.dtsi" ++#include "bcm283x-rpi-i2c0mux_0_28.dtsi" ++ ++/ { ++ compatible = "raspberrypi,2-model-b-rev2", "brcm,bcm2837"; ++ model = "Raspberry Pi 2 Model B rev 1.2"; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins = <40 45>; ++ brcm,function = <4>; ++ }; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++}; ++ ++&i2c0if { ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&gpio 47 0>; ++ }; ++ ++ pwr_led: pwr { ++ label = "led1"; ++ linux,default-trigger = "input"; ++ gpios = <&gpio 35 0>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ ++ pwr_led_gpio = <&pwr_led>,"gpios:4"; ++ pwr_led_activelow = <&pwr_led>,"gpios:8"; ++ pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2710-rpi-3-b-plus.dts b/arch/arm/boot/dts/bcm2710-rpi-3-b-plus.dts +new file mode 100644 +index 000000000000..4e4e47100831 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2710-rpi-3-b-plus.dts +@@ -0,0 +1,196 @@ ++/dts-v1/; ++ ++#include "bcm2710.dtsi" ++#include "bcm2709-rpi.dtsi" ++#include "bcm283x-rpi-lan7515.dtsi" ++#include "bcm283x-rpi-csi1-2lane.dtsi" ++#include "bcm283x-rpi-i2c0mux_0_44.dtsi" ++#include "bcm271x-rpi-bt.dtsi" ++ ++/ { ++ compatible = "raspberrypi,3-model-b-plus", "brcm,bcm2837"; ++ model = "Raspberry Pi 3 Model B+"; ++ ++ chosen { ++ bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1"; ++ }; ++ ++ aliases { ++ serial0 = &uart1; ++ serial1 = &uart0; ++ mmc1 = &mmcnr; ++ }; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ sdio_pins: sdio_pins { ++ brcm,pins = <34 35 36 37 38 39>; ++ brcm,function = <7>; // alt3 = SD1 ++ brcm,pull = <0 2 2 2 2 2>; ++ }; ++ ++ bt_pins: bt_pins { ++ brcm,pins = <43>; ++ brcm,function = <4>; /* alt0:GPCLK2 */ ++ brcm,pull = <0>; ++ }; ++ ++ uart0_pins: uart0_pins { ++ brcm,pins = <32 33>; ++ brcm,function = <7>; /* alt3=UART0 */ ++ brcm,pull = <0 2>; ++ }; ++ ++ uart1_pins: uart1_pins { ++ brcm,pins; ++ brcm,function; ++ brcm,pull; ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins = <40 41>; ++ brcm,function = <4>; ++ }; ++}; ++ ++&mmcnr { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdio_pins>; ++ bus-width = <4>; ++ status = "okay"; ++}; ++ ++&firmware { ++ expgpio: expgpio { ++ compatible = "raspberrypi,firmware-gpio"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ status = "okay"; ++ }; ++}; ++ ++&uart0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_pins &bt_pins>; ++ status = "okay"; ++}; ++ ++&uart1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart1_pins>; ++ status = "okay"; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++}; ++ ++&i2c0if { ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&gpio 29 0>; ++ }; ++ ++ pwr_led: pwr { ++ label = "led1"; ++ linux,default-trigger = "default-on"; ++ gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++ð_phy { ++ microchip,eee-enabled; ++ microchip,tx-lpi-timer = <600>; /* non-aggressive*/ ++ microchip,downshift-after = <2>; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ ++ pwr_led_gpio = <&pwr_led>,"gpios:4"; ++ pwr_led_activelow = <&pwr_led>,"gpios:8"; ++ pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; ++ ++ eee = <ð_phy>,"microchip,eee-enabled?"; ++ tx_lpi_timer = <ð_phy>,"microchip,tx-lpi-timer:0"; ++ eth_led0 = <ð_phy>,"microchip,led-modes:0"; ++ eth_led1 = <ð_phy>,"microchip,led-modes:4"; ++ eth_downshift_after = <ð_phy>,"microchip,downshift-after:0"; ++ eth_max_speed = <ð_phy>,"max-speed:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2710-rpi-3-b.dts b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts +new file mode 100644 +index 000000000000..8989c00b03e5 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2710-rpi-3-b.dts +@@ -0,0 +1,198 @@ ++/dts-v1/; ++ ++#include "bcm2710.dtsi" ++#include "bcm2709-rpi.dtsi" ++#include "bcm283x-rpi-smsc9514.dtsi" ++#include "bcm283x-rpi-csi1-2lane.dtsi" ++#include "bcm283x-rpi-i2c0mux_0_44.dtsi" ++#include "bcm271x-rpi-bt.dtsi" ++ ++/ { ++ compatible = "raspberrypi,3-model-b", "brcm,bcm2837"; ++ model = "Raspberry Pi 3 Model B"; ++ ++ chosen { ++ bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1"; ++ }; ++ ++ aliases { ++ serial0 = &uart1; ++ serial1 = &uart0; ++ mmc1 = &mmcnr; ++ }; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ sdio_pins: sdio_pins { ++ brcm,pins = <34 35 36 37 38 39>; ++ brcm,function = <7>; // alt3 = SD1 ++ brcm,pull = <0 2 2 2 2 2>; ++ }; ++ ++ bt_pins: bt_pins { ++ brcm,pins = <43>; ++ brcm,function = <4>; /* alt0:GPCLK2 */ ++ brcm,pull = <0>; ++ }; ++ ++ uart0_pins: uart0_pins { ++ brcm,pins = <32 33>; ++ brcm,function = <7>; /* alt3=UART0 */ ++ brcm,pull = <0 2>; ++ }; ++ ++ uart1_pins: uart1_pins { ++ brcm,pins; ++ brcm,function; ++ brcm,pull; ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins = <40 41>; ++ brcm,function = <4>; ++ }; ++}; ++ ++&mmcnr { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdio_pins>; ++ bus-width = <4>; ++ status = "okay"; ++}; ++ ++&soc { ++ virtgpio: virtgpio { ++ compatible = "brcm,bcm2835-virtgpio"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ firmware = <&firmware>; ++ status = "okay"; ++ }; ++ ++}; ++ ++&firmware { ++ expgpio: expgpio { ++ compatible = "raspberrypi,firmware-gpio"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ status = "okay"; ++ }; ++}; ++ ++&uart0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_pins &bt_pins>; ++ status = "okay"; ++}; ++ ++&uart1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart1_pins>; ++ status = "okay"; ++}; ++ ++&bt { ++ max-speed = <921600>; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++}; ++ ++&i2c0if { ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&virtgpio 0 0>; ++ }; ++ ++ pwr_led: pwr { ++ label = "led1"; ++ linux,default-trigger = "input"; ++ gpios = <&expgpio 7 0>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&expgpio 4 GPIO_ACTIVE_LOW>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ ++ pwr_led_gpio = <&pwr_led>,"gpios:4"; ++ pwr_led_activelow = <&pwr_led>,"gpios:8"; ++ pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2710-rpi-cm3.dts b/arch/arm/boot/dts/bcm2710-rpi-cm3.dts +new file mode 100644 +index 000000000000..f972979281f5 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2710-rpi-cm3.dts +@@ -0,0 +1,133 @@ ++/dts-v1/; ++ ++#include "bcm2710.dtsi" ++#include "bcm2709-rpi.dtsi" ++#include "bcm283x-rpi-csi0-2lane.dtsi" ++#include "bcm283x-rpi-csi1-4lane.dtsi" ++#include "bcm283x-rpi-i2c0mux_0_28.dtsi" ++/ { ++ compatible = "raspberrypi,3-compute-module", "brcm,bcm2837"; ++ model = "Raspberry Pi Compute Module 3"; ++}; ++ ++&uart0 { ++ status = "okay"; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = <1>; /* output */ ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ ++ audio_pins: audio_pins { ++ brcm,pins; ++ brcm,function; ++ }; ++}; ++ ++&soc { ++ virtgpio: virtgpio { ++ compatible = "brcm,bcm2835-virtgpio"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ firmware = <&firmware>; ++ status = "okay"; ++ }; ++ ++}; ++ ++&firmware { ++ expgpio: expgpio { ++ compatible = "raspberrypi,firmware-gpio"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ status = "okay"; ++ }; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++}; ++ ++&i2c0if { ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2c2 { ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&virtgpio 0 0>; ++ }; ++}; ++ ++&hdmi { ++ hpd-gpios = <&expgpio 0 GPIO_ACTIVE_LOW>; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2710.dtsi b/arch/arm/boot/dts/bcm2710.dtsi +new file mode 100644 +index 000000000000..4e47480dd933 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2710.dtsi +@@ -0,0 +1,29 @@ ++#include "bcm2837.dtsi" ++#include "bcm270x.dtsi" ++ ++/ { ++ compatible = "brcm,bcm2837", "brcm,bcm2836"; ++ ++ arm-pmu { ++#ifdef RPI364 ++ compatible = "arm,armv8-pmuv3", "arm,cortex-a7-pmu"; ++#else ++ compatible = "arm,cortex-a7-pmu"; ++#endif ++ }; ++ ++ soc { ++ /delete-node/ timer@7e003000; ++ }; ++ ++ __overrides__ { ++ arm_freq = <&cpu0>, "clock-frequency:0", ++ <&cpu1>, "clock-frequency:0", ++ <&cpu2>, "clock-frequency:0", ++ <&cpu3>, "clock-frequency:0"; ++ }; ++}; ++ ++&vc4 { ++ status = "disabled"; ++}; +diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts +index 5395e8c2484e..3e67c2b634be 100644 +--- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts ++++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts +@@ -2,7 +2,6 @@ + /dts-v1/; + #include "bcm2711.dtsi" + #include "bcm2835-rpi.dtsi" +-#include "bcm283x-rpi-usb-peripheral.dtsi" + + #include + +@@ -95,7 +94,7 @@ expgpio: gpio { + "VDD_SD_IO_SEL", + "CAM_GPIO", + "SD_PWR_ON", +- ""; ++ "SD_OC_N"; + status = "okay"; + }; + +@@ -301,3 +300,306 @@ &vc4 { + &vec { + status = "disabled"; + }; ++ ++// ============================================= ++// Downstream rpi- changes ++ ++#define BCM2711 ++ ++#include "bcm270x.dtsi" ++#include "bcm271x-rpi-bt.dtsi" ++ ++/ { ++ soc { ++ /delete-node/ pixelvalve@7e807000; ++ /delete-node/ hdmi@7e902000; ++ }; ++}; ++ ++#include "bcm2711-rpi.dtsi" ++#include "bcm283x-rpi-csi1-2lane.dtsi" ++#include "bcm283x-rpi-i2c0mux_0_44.dtsi" ++ ++/ { ++ chosen { ++ bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1"; ++ }; ++ ++ aliases { ++ serial0 = &uart1; ++ serial1 = &uart0; ++ mmc0 = &emmc2; ++ mmc1 = &mmcnr; ++ mmc2 = &sdhost; ++ /delete-property/ i2c2; ++ i2c3 = &i2c3; ++ i2c4 = &i2c4; ++ i2c5 = &i2c5; ++ i2c6 = &i2c6; ++ /delete-property/ intc; ++ }; ++ ++ /delete-node/ wifi-pwrseq; ++}; ++ ++&mmcnr { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdio_pins>; ++ bus-width = <4>; ++ status = "okay"; ++}; ++ ++&uart0 { ++ pinctrl-0 = <&uart0_pins &bt_pins>; ++ status = "okay"; ++}; ++ ++&uart1 { ++ pinctrl-0 = <&uart1_pins>; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = ; ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = ; ++ }; ++ ++ spi3_pins: spi3_pins { ++ brcm,pins = <1 2 3>; ++ brcm,function = ; ++ }; ++ ++ spi3_cs_pins: spi3_cs_pins { ++ brcm,pins = <0 24>; ++ brcm,function = ; ++ }; ++ ++ spi4_pins: spi4_pins { ++ brcm,pins = <5 6 7>; ++ brcm,function = ; ++ }; ++ ++ spi4_cs_pins: spi4_cs_pins { ++ brcm,pins = <4 25>; ++ brcm,function = ; ++ }; ++ ++ spi5_pins: spi5_pins { ++ brcm,pins = <13 14 15>; ++ brcm,function = ; ++ }; ++ ++ spi5_cs_pins: spi5_cs_pins { ++ brcm,pins = <12 26>; ++ brcm,function = ; ++ }; ++ ++ spi6_pins: spi6_pins { ++ brcm,pins = <19 20 21>; ++ brcm,function = ; ++ }; ++ ++ spi6_cs_pins: spi6_cs_pins { ++ brcm,pins = <18 27>; ++ brcm,function = ; ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = ; ++ brcm,pull = ; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = ; ++ brcm,pull = ; ++ }; ++ ++ i2c3_pins: i2c3 { ++ brcm,pins = <4 5>; ++ brcm,function = ; ++ brcm,pull = ; ++ }; ++ ++ i2c4_pins: i2c4 { ++ brcm,pins = <8 9>; ++ brcm,function = ; ++ brcm,pull = ; ++ }; ++ ++ i2c5_pins: i2c5 { ++ brcm,pins = <12 13>; ++ brcm,function = ; ++ brcm,pull = ; ++ }; ++ ++ i2c6_pins: i2c6 { ++ brcm,pins = <22 23>; ++ brcm,function = ; ++ brcm,pull = ; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = ; ++ }; ++ ++ sdio_pins: sdio_pins { ++ brcm,pins = <34 35 36 37 38 39>; ++ brcm,function = ; // alt3 = SD1 ++ brcm,pull = <0 2 2 2 2 2>; ++ }; ++ ++ bt_pins: bt_pins { ++ brcm,pins = "-"; // non-empty to keep btuart happy, //4 = 0 ++ // to fool pinctrl ++ brcm,function = <0>; ++ brcm,pull = <2>; ++ }; ++ ++ uart0_pins: uart0_pins { ++ brcm,pins = <32 33>; ++ brcm,function = ; ++ brcm,pull = <0 2>; ++ }; ++ ++ uart1_pins: uart1_pins { ++ brcm,pins; ++ brcm,function; ++ brcm,pull; ++ }; ++ ++ uart2_pins: uart2_pins { ++ brcm,pins = <0 1>; ++ brcm,function = ; ++ brcm,pull = <0 2>; ++ }; ++ ++ uart3_pins: uart3_pins { ++ brcm,pins = <4 5>; ++ brcm,function = ; ++ brcm,pull = <0 2>; ++ }; ++ ++ uart4_pins: uart4_pins { ++ brcm,pins = <8 9>; ++ brcm,function = ; ++ brcm,pull = <0 2>; ++ }; ++ ++ uart5_pins: uart5_pins { ++ brcm,pins = <12 13>; ++ brcm,function = ; ++ brcm,pull = <0 2>; ++ }; ++}; ++ ++&i2c0if { ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ /delete-property/ i2c2_baudrate; ++ /delete-property/ i2c2_iknowwhatimdoing; ++ }; ++}; ++ ++// ============================================= ++// Board specific stuff here ++ ++&sdhost { ++ status = "disabled"; ++}; ++ ++&phy1 { ++ led-modes = <0x00 0x08>; /* link/activity link */ ++}; ++ ++&gpio { ++ audio_pins: audio_pins { ++ brcm,pins = <40 41>; ++ brcm,function = <4>; ++ }; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ pwr_led: pwr { ++ label = "led1"; ++ linux,default-trigger = "default-on"; ++ gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; ++ }; ++}; ++ ++&pwm1 { ++ status = "disabled"; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ ++ pwr_led_gpio = <&pwr_led>,"gpios:4"; ++ pwr_led_activelow = <&pwr_led>,"gpios:8"; ++ pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; ++ ++ eth_led0 = <&phy1>,"led-modes:0"; ++ eth_led1 = <&phy1>,"led-modes:4"; ++ ++ sd_poll_once = <&emmc2>, "non-removable?"; ++ spi_dma4 = <&spi0>, "dmas:0=", <&dma40>, ++ <&spi0>, "dmas:8=", <&dma40>; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2711-rpi-cm4.dts b/arch/arm/boot/dts/bcm2711-rpi-cm4.dts +new file mode 100644 +index 000000000000..0ca3a0126220 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2711-rpi-cm4.dts +@@ -0,0 +1,609 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/dts-v1/; ++#include "bcm2711.dtsi" ++#include "bcm2835-rpi.dtsi" ++ ++/ { ++ compatible = "raspberrypi,4-compute-module", "brcm,bcm2711"; ++ model = "Raspberry Pi Compute Module 4"; ++ ++ chosen { ++ /* 8250 auxiliary UART instead of pl011 */ ++ stdout-path = "serial1:115200n8"; ++ }; ++ ++ /* Will be filled by the bootloader */ ++ memory@0 { ++ device_type = "memory"; ++ reg = <0 0 0>; ++ }; ++ ++ aliases { ++ emmc2bus = &emmc2bus; ++ ethernet0 = &genet; ++ pcie0 = &pcie0; ++ }; ++ ++ leds { ++ act { ++ gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ pwr { ++ label = "PWR"; ++ gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; ++ default-state = "keep"; ++ linux,default-trigger = "default-on"; ++ }; ++ }; ++ ++ wifi_pwrseq: wifi-pwrseq { ++ compatible = "mmc-pwrseq-simple"; ++ reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>; ++ }; ++ ++ sd_io_1v8_reg: sd_io_1v8_reg { ++ compatible = "regulator-gpio"; ++ regulator-name = "vdd-sd-io"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <3300000>; ++ regulator-boot-on; ++ regulator-always-on; ++ regulator-settling-time-us = <5000>; ++ gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>; ++ states = <1800000 0x1 ++ 3300000 0x0>; ++ status = "okay"; ++ }; ++ ++ sd_vcc_reg: sd_vcc_reg { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc-sd"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ regulator-boot-on; ++ enable-active-high; ++ gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>; ++ }; ++}; ++ ++&ddc0 { ++ status = "okay"; ++}; ++ ++&ddc1 { ++ status = "okay"; ++}; ++ ++&firmware { ++ expgpio: gpio { ++ compatible = "raspberrypi,firmware-gpio"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ gpio-line-names = "BT_ON", ++ "WL_ON", ++ "PWR_LED_OFF", ++ "ANT1", ++ "VDD_SD_IO_SEL", ++ "CAM_GPIO", ++ "SD_PWR_ON", ++ "ANT2"; ++ status = "okay"; ++ ++ ant1: ant1 { ++ gpio-hog; ++ gpios = <3 GPIO_ACTIVE_HIGH>; ++ output-high; ++ }; ++ ++ ant2: ant2 { ++ gpio-hog; ++ gpios = <7 GPIO_ACTIVE_HIGH>; ++ output-low; ++ }; ++ }; ++}; ++ ++&gpio { ++ /* ++ * Parts taken from rpi_SCH_4b_4p0_reduced.pdf and ++ * the official GPU firmware DT blob. ++ * ++ * Legend: ++ * "FOO" = GPIO line named "FOO" on the schematic ++ * "FOO_N" = GPIO line named "FOO" on schematic, active low ++ */ ++ gpio-line-names = "ID_SDA", ++ "ID_SCL", ++ "SDA1", ++ "SCL1", ++ "GPIO_GCLK", ++ "GPIO5", ++ "GPIO6", ++ "SPI_CE1_N", ++ "SPI_CE0_N", ++ "SPI_MISO", ++ "SPI_MOSI", ++ "SPI_SCLK", ++ "GPIO12", ++ "GPIO13", ++ /* Serial port */ ++ "TXD1", ++ "RXD1", ++ "GPIO16", ++ "GPIO17", ++ "GPIO18", ++ "GPIO19", ++ "GPIO20", ++ "GPIO21", ++ "GPIO22", ++ "GPIO23", ++ "GPIO24", ++ "GPIO25", ++ "GPIO26", ++ "GPIO27", ++ "RGMII_MDIO", ++ "RGMIO_MDC", ++ /* Used by BT module */ ++ "CTS0", ++ "RTS0", ++ "TXD0", ++ "RXD0", ++ /* Used by Wifi */ ++ "SD1_CLK", ++ "SD1_CMD", ++ "SD1_DATA0", ++ "SD1_DATA1", ++ "SD1_DATA2", ++ "SD1_DATA3", ++ /* Shared with SPI flash */ ++ "PWM0_MISO", ++ "PWM1_MOSI", ++ "STATUS_LED_G_CLK", ++ "SPIFLASH_CE_N", ++ "SDA0", ++ "SCL0", ++ "RGMII_RXCLK", ++ "RGMII_RXCTL", ++ "RGMII_RXD0", ++ "RGMII_RXD1", ++ "RGMII_RXD2", ++ "RGMII_RXD3", ++ "RGMII_TXCLK", ++ "RGMII_TXCTL", ++ "RGMII_TXD0", ++ "RGMII_TXD1", ++ "RGMII_TXD2", ++ "RGMII_TXD3"; ++}; ++ ++&hdmi0 { ++ clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 0>, <&clk_27MHz>; ++ clock-names = "hdmi", "bvb", "audio", "cec"; ++ status = "okay"; ++}; ++ ++&hdmi1 { ++ clocks = <&firmware_clocks 13>, <&firmware_clocks 14>, <&dvp 1>, <&clk_27MHz>; ++ clock-names = "hdmi", "bvb", "audio", "cec"; ++ status = "okay"; ++}; ++ ++&hvs { ++ clocks = <&firmware_clocks 4>; ++}; ++ ++&pixelvalve0 { ++ status = "okay"; ++}; ++ ++&pixelvalve1 { ++ status = "okay"; ++}; ++ ++&pixelvalve2 { ++ status = "okay"; ++}; ++ ++&pixelvalve4 { ++ status = "okay"; ++}; ++ ++&vc4 { ++ status = "okay"; ++}; ++ ++&vec { ++ status = "disabled"; ++}; ++ ++&pwm1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pwm1_0_gpio40 &pwm1_1_gpio41>; ++ status = "okay"; ++}; ++ ++/* SDHCI is used to control the SDIO for wireless */ ++&sdhci { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&emmc_gpio34>; ++ bus-width = <4>; ++ non-removable; ++ mmc-pwrseq = <&wifi_pwrseq>; ++ status = "okay"; ++ ++ brcmf: wifi@1 { ++ reg = <1>; ++ compatible = "brcm,bcm4329-fmac"; ++ }; ++}; ++ ++/* EMMC2 is used to drive the EMMC card */ ++&emmc2 { ++ bus-width = <8>; ++ vqmmc-supply = <&sd_io_1v8_reg>; ++ vmmc-supply = <&sd_vcc_reg>; ++ broken-cd; ++ status = "okay"; ++}; ++ ++&genet { ++ phy-handle = <&phy1>; ++ phy-mode = "rgmii-rxid"; ++ status = "okay"; ++}; ++ ++&genet_mdio { ++ phy1: ethernet-phy@1 { ++ /* No PHY interrupt */ ++ reg = <0x1>; ++ }; ++}; ++ ++/* uart0 communicates with the BT module */ ++&uart0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>; ++ uart-has-rtscts; ++ status = "okay"; ++ ++ bluetooth { ++ compatible = "brcm,bcm43438-bt"; ++ max-speed = <2000000>; ++ shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; ++ }; ++}; ++ ++/* uart1 is mapped to the pin header */ ++&uart1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart1_gpio14>; ++ status = "okay"; ++}; ++ ++&vchiq { ++ interrupts = ; ++}; ++ ++// ============================================= ++// Downstream rpi- changes ++ ++#define BCM2711 ++ ++#include "bcm270x.dtsi" ++#include "bcm271x-rpi-bt.dtsi" ++ ++/ { ++ soc { ++ /delete-node/ pixelvalve@7e807000; ++ /delete-node/ hdmi@7e902000; ++ }; ++}; ++ ++#include "bcm2711-rpi.dtsi" ++#include "bcm283x-rpi-csi0-2lane.dtsi" ++#include "bcm283x-rpi-csi1-4lane.dtsi" ++#include "bcm283x-rpi-i2c0mux_0_44.dtsi" ++ ++/ { ++ chosen { ++ bootargs = "coherent_pool=1M 8250.nr_uarts=1 snd_bcm2835.enable_compat_alsa=0 snd_bcm2835.enable_hdmi=1 snd_bcm2835.enable_headphones=1"; ++ }; ++ ++ aliases { ++ serial0 = &uart1; ++ serial1 = &uart0; ++ mmc0 = &emmc2; ++ mmc1 = &mmcnr; ++ mmc2 = &sdhost; ++ /delete-property/ i2c2; ++ i2c3 = &i2c3; ++ i2c4 = &i2c4; ++ i2c5 = &i2c5; ++ i2c6 = &i2c6; ++ /delete-property/ intc; ++ }; ++ ++ /delete-node/ wifi-pwrseq; ++}; ++ ++&mmcnr { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdio_pins>; ++ bus-width = <4>; ++ status = "okay"; ++}; ++ ++&uart0 { ++ pinctrl-0 = <&uart0_pins &bt_pins>; ++ status = "okay"; ++}; ++ ++&uart1 { ++ pinctrl-0 = <&uart1_pins>; ++}; ++ ++&spi0 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins &spi0_cs_pins>; ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ ++ spidev0: spidev@0{ ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++ ++ spidev1: spidev@1{ ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ }; ++}; ++ ++&gpio { ++ spi0_pins: spi0_pins { ++ brcm,pins = <9 10 11>; ++ brcm,function = ; ++ }; ++ ++ spi0_cs_pins: spi0_cs_pins { ++ brcm,pins = <8 7>; ++ brcm,function = ; ++ }; ++ ++ spi3_pins: spi3_pins { ++ brcm,pins = <1 2 3>; ++ brcm,function = ; ++ }; ++ ++ spi3_cs_pins: spi3_cs_pins { ++ brcm,pins = <0 24>; ++ brcm,function = ; ++ }; ++ ++ spi4_pins: spi4_pins { ++ brcm,pins = <5 6 7>; ++ brcm,function = ; ++ }; ++ ++ spi4_cs_pins: spi4_cs_pins { ++ brcm,pins = <4 25>; ++ brcm,function = ; ++ }; ++ ++ spi5_pins: spi5_pins { ++ brcm,pins = <13 14 15>; ++ brcm,function = ; ++ }; ++ ++ spi5_cs_pins: spi5_cs_pins { ++ brcm,pins = <12 26>; ++ brcm,function = ; ++ }; ++ ++ spi6_pins: spi6_pins { ++ brcm,pins = <19 20 21>; ++ brcm,function = ; ++ }; ++ ++ spi6_cs_pins: spi6_cs_pins { ++ brcm,pins = <18 27>; ++ brcm,function = ; ++ }; ++ ++ i2c0_pins: i2c0 { ++ brcm,pins = <0 1>; ++ brcm,function = ; ++ brcm,pull = ; ++ }; ++ ++ i2c1_pins: i2c1 { ++ brcm,pins = <2 3>; ++ brcm,function = ; ++ brcm,pull = ; ++ }; ++ ++ i2c3_pins: i2c3 { ++ brcm,pins = <4 5>; ++ brcm,function = ; ++ brcm,pull = ; ++ }; ++ ++ i2c4_pins: i2c4 { ++ brcm,pins = <8 9>; ++ brcm,function = ; ++ brcm,pull = ; ++ }; ++ ++ i2c5_pins: i2c5 { ++ brcm,pins = <12 13>; ++ brcm,function = ; ++ brcm,pull = ; ++ }; ++ ++ i2c6_pins: i2c6 { ++ brcm,pins = <22 23>; ++ brcm,function = ; ++ brcm,pull = ; ++ }; ++ ++ i2s_pins: i2s { ++ brcm,pins = <18 19 20 21>; ++ brcm,function = ; ++ }; ++ ++ sdio_pins: sdio_pins { ++ brcm,pins = <34 35 36 37 38 39>; ++ brcm,function = ; // alt3 = SD1 ++ brcm,pull = <0 2 2 2 2 2>; ++ }; ++ ++ bt_pins: bt_pins { ++ brcm,pins = "-"; // non-empty to keep btuart happy, //4 = 0 ++ // to fool pinctrl ++ brcm,function = <0>; ++ brcm,pull = <2>; ++ }; ++ ++ uart0_pins: uart0_pins { ++ brcm,pins = <32 33>; ++ brcm,function = ; ++ brcm,pull = <0 2>; ++ }; ++ ++ uart1_pins: uart1_pins { ++ brcm,pins; ++ brcm,function; ++ brcm,pull; ++ }; ++ ++ uart2_pins: uart2_pins { ++ brcm,pins = <0 1>; ++ brcm,function = ; ++ brcm,pull = <0 2>; ++ }; ++ ++ uart3_pins: uart3_pins { ++ brcm,pins = <4 5>; ++ brcm,function = ; ++ brcm,pull = <0 2>; ++ }; ++ ++ uart4_pins: uart4_pins { ++ brcm,pins = <8 9>; ++ brcm,function = ; ++ brcm,pull = <0 2>; ++ }; ++ ++ uart5_pins: uart5_pins { ++ brcm,pins = <12 13>; ++ brcm,function = ; ++ brcm,pull = <0 2>; ++ }; ++}; ++ ++&i2c0if { ++ clock-frequency = <100000>; ++}; ++ ++&i2c1 { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ clock-frequency = <100000>; ++}; ++ ++&i2s { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2s_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ /delete-property/ i2c2_baudrate; ++ /delete-property/ i2c2_iknowwhatimdoing; ++ }; ++}; ++ ++// ============================================= ++// Board specific stuff here ++ ++&pcie0 { ++ brcm,enable-l1ss; ++}; ++ ++&sdhost { ++ status = "disabled"; ++}; ++ ++&phy1 { ++ led-modes = <0x00 0x08>; /* link/activity link */ ++}; ++ ++&gpio { ++ audio_pins: audio_pins { ++ brcm,pins = <40 41>; ++ brcm,function = <4>; ++ }; ++}; ++ ++&leds { ++ act_led: act { ++ label = "led0"; ++ linux,default-trigger = "mmc0"; ++ gpios = <&gpio 42 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ pwr_led: pwr { ++ label = "led1"; ++ linux,default-trigger = "default-on"; ++ gpios = <&expgpio 2 GPIO_ACTIVE_LOW>; ++ }; ++}; ++ ++&pwm1 { ++ status = "disabled"; ++}; ++ ++&audio { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&audio_pins>; ++}; ++ ++/ { ++ __overrides__ { ++ act_led_gpio = <&act_led>,"gpios:4"; ++ act_led_activelow = <&act_led>,"gpios:8"; ++ act_led_trigger = <&act_led>,"linux,default-trigger"; ++ ++ pwr_led_gpio = <&pwr_led>,"gpios:4"; ++ pwr_led_activelow = <&pwr_led>,"gpios:8"; ++ pwr_led_trigger = <&pwr_led>,"linux,default-trigger"; ++ ++ eth_led0 = <&phy1>,"led-modes:0"; ++ eth_led1 = <&phy1>,"led-modes:4"; ++ ++ ant1 = <&ant1>,"output-high?=on", ++ <&ant1>, "output-low?=off", ++ <&ant2>, "output-high?=off", ++ <&ant2>, "output-low?=on"; ++ ant2 = <&ant1>,"output-high?=off", ++ <&ant1>, "output-low?=on", ++ <&ant2>, "output-high?=on", ++ <&ant2>, "output-low?=off"; ++ noant = <&ant1>,"output-high?=off", ++ <&ant1>, "output-low?=on", ++ <&ant2>, "output-high?=off", ++ <&ant2>, "output-low?=on"; ++ ++ sd_poll_once = <&emmc2>, "non-removable?"; ++ spi_dma4 = <&spi0>, "dmas:0=", <&dma40>, ++ <&spi0>, "dmas:8=", <&dma40>; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2711-rpi.dtsi b/arch/arm/boot/dts/bcm2711-rpi.dtsi +new file mode 100644 +index 000000000000..4f903a787d65 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm2711-rpi.dtsi +@@ -0,0 +1,201 @@ ++// SPDX-License-Identifier: GPL-2.0 ++#include "bcm270x-rpi.dtsi" ++ ++/ { ++ __overrides__ { ++ arm_freq; ++ }; ++ ++ v3dbus: v3dbus { ++ compatible = "simple-bus"; ++ #address-cells = <1>; ++ #size-cells = <2>; ++ ranges = <0x7c500000 0x0 0xfc500000 0x0 0x03300000>, ++ <0x40000000 0x0 0xff800000 0x0 0x00800000>; ++ dma-ranges = <0x00000000 0x0 0x00000000 0x4 0x00000000>; ++ ++ v3d: v3d@7ec04000 { ++ compatible = "brcm,2711-v3d"; ++ reg = ++ <0x7ec00000 0x0 0x4000>, ++ <0x7ec04000 0x0 0x4000>; ++ reg-names = "hub", "core0"; ++ ++ power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>; ++ resets = <&pm BCM2835_RESET_V3D>; ++ clocks = <&firmware_clocks 5>; ++ clocks-names = "v3d"; ++ interrupts = ; ++ status = "disabled"; ++ }; ++ }; ++ ++ scb: scb { ++ /* Add a label */ ++ }; ++}; ++ ++&cma { ++ /* Limit cma to the lower 768MB to allow room for HIGHMEM on 32-bit */ ++ alloc-ranges = <0x0 0x00000000 0x30000000>; ++}; ++ ++&scb { ++ ranges = <0x0 0x7c000000 0x0 0xfc000000 0x0 0x03800000>, ++ <0x0 0x40000000 0x0 0xff800000 0x0 0x00800000>, ++ <0x6 0x00000000 0x6 0x00000000 0x0 0x40000000>, ++ <0x0 0x00000000 0x0 0x00000000 0x0 0xfc000000>; ++ dma-ranges = <0x0 0x00000000 0x0 0x00000000 0x4 0x00000000>; ++ ++ dma40: dma@7e007b00 { ++ compatible = "brcm,bcm2711-dma"; ++ reg = <0x0 0x7e007b00 0x0 0x400>; ++ interrupts = ++ , /* dma4 11 */ ++ , /* dma4 12 */ ++ , /* dma4 13 */ ++ ; /* dma4 14 */ ++ interrupt-names = "dma11", ++ "dma12", ++ "dma13", ++ "dma14"; ++ #dma-cells = <1>; ++ brcm,dma-channel-mask = <0x7800>; ++ }; ++ ++ xhci: xhci@7e9c0000 { ++ compatible = "generic-xhci"; ++ status = "disabled"; ++ reg = <0x0 0x7e9c0000 0x0 0x100000>; ++ interrupts = ; ++ power-domains = <&power RPI_POWER_DOMAIN_USB>; ++ }; ++ ++ hevc-decoder@7eb00000 { ++ compatible = "raspberrypi,rpivid-hevc-decoder"; ++ reg = <0x0 0x7eb00000 0x0 0x10000>; ++ status = "okay"; ++ }; ++ ++ rpivid-local-intc@7eb10000 { ++ compatible = "raspberrypi,rpivid-local-intc"; ++ reg = <0x0 0x7eb10000 0x0 0x1000>; ++ status = "okay"; ++ interrupts = ; ++ }; ++ ++ h264-decoder@7eb20000 { ++ compatible = "raspberrypi,rpivid-h264-decoder"; ++ reg = <0x0 0x7eb20000 0x0 0x10000>; ++ status = "okay"; ++ }; ++ ++ vp9-decoder@7eb30000 { ++ compatible = "raspberrypi,rpivid-vp9-decoder"; ++ reg = <0x0 0x7eb30000 0x0 0x10000>; ++ status = "okay"; ++ }; ++}; ++ ++&dma40 { ++ /* The VPU firmware uses DMA channel 11 for VCHIQ */ ++ brcm,dma-channel-mask = <0x7000>; ++}; ++ ++&vchiq { ++ compatible = "brcm,bcm2711-vchiq"; ++}; ++ ++&firmwarekms { ++ compatible = "raspberrypi,rpi-firmware-kms-2711"; ++ interrupts = ; ++}; ++ ++&smi { ++ interrupts = ; ++}; ++ ++&mmc { ++ interrupts = ; ++}; ++ ++&mmcnr { ++ interrupts = ; ++}; ++ ++&csi0 { ++ interrupts = ; ++}; ++ ++&csi1 { ++ interrupts = ; ++}; ++ ++&random { ++ compatible = "brcm,bcm2711-rng200"; ++ status = "okay"; ++}; ++ ++&usb { ++ /* Enable the FIQ support */ ++ reg = <0x7e980000 0x10000>, ++ <0x7e00b200 0x200>; ++ interrupts = , ++ ; ++ status = "disabled"; ++}; ++ ++&gpio { ++ interrupts = , ++ ; ++}; ++ ++&emmc2 { ++ mmc-ddr-3_3v; ++}; ++ ++&vc4 { ++ status = "disabled"; ++}; ++ ++&pixelvalve0 { ++ status = "disabled"; ++}; ++ ++&pixelvalve1 { ++ status = "disabled"; ++}; ++ ++&pixelvalve2 { ++ status = "disabled"; ++}; ++ ++&pixelvalve3 { ++ status = "disabled"; ++}; ++ ++&pixelvalve4 { ++ status = "disabled"; ++}; ++ ++&hdmi0 { ++ dmas = <&dma (10|(1<<27))>; ++ status = "disabled"; ++}; ++ ++&ddc0 { ++ status = "disabled"; ++}; ++ ++&hdmi1 { ++ dmas = <&dma (17|(1<<27))>; ++ status = "disabled"; ++}; ++ ++&ddc1 { ++ status = "disabled"; ++}; ++ ++&dvp { ++ status = "disabled"; ++}; +diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi +index 3d040f6e2a20..6e0339266027 100644 +--- a/arch/arm/boot/dts/bcm2711.dtsi ++++ b/arch/arm/boot/dts/bcm2711.dtsi +@@ -318,7 +318,8 @@ hdmi0: hdmi@7ef00700 { + <0x7ef01f00 0x400>, + <0x7ef00200 0x80>, + <0x7ef04300 0x100>, +- <0x7ef20000 0x100>; ++ <0x7ef20000 0x100>, ++ <0x7ef00100 0x30>; + reg-names = "hdmi", + "dvp", + "phy", +@@ -327,12 +328,18 @@ hdmi0: hdmi@7ef00700 { + "metadata", + "csc", + "cec", +- "hd"; ++ "hd", ++ "intr2"; ++ clocks = <&firmware_clocks 13>, ++ <&firmware_clocks 14>, ++ <&dvp 0>, ++ <&clk_27MHz>; + clock-names = "hdmi", "bvb", "audio", "cec"; + resets = <&dvp 0>; + ddc = <&ddc0>; + dmas = <&dma 10>; + dma-names = "audio-rx"; ++ interrupts = ; + status = "disabled"; + }; + +@@ -354,7 +361,8 @@ hdmi1: hdmi@7ef05700 { + <0x7ef06f00 0x400>, + <0x7ef00280 0x80>, + <0x7ef09300 0x100>, +- <0x7ef20000 0x100>; ++ <0x7ef20000 0x100>, ++ <0x7ef00100 0x30>; + reg-names = "hdmi", + "dvp", + "phy", +@@ -363,12 +371,18 @@ hdmi1: hdmi@7ef05700 { + "metadata", + "csc", + "cec", +- "hd"; ++ "hd", ++ "intr2"; + ddc = <&ddc1>; + clock-names = "hdmi", "bvb", "audio", "cec"; ++ clocks = <&firmware_clocks 13>, ++ <&firmware_clocks 14>, ++ <&dvp 0>, ++ <&clk_27MHz>; + resets = <&dvp 1>; + dmas = <&dma 17>; + dma-names = "audio-rx"; ++ interrupts = ; + status = "disabled"; + }; + +@@ -468,14 +482,14 @@ cpu3: cpu@3 { + scb { + compatible = "simple-bus"; + #address-cells = <2>; +- #size-cells = <1>; ++ #size-cells = <2>; + +- ranges = <0x0 0x7c000000 0x0 0xfc000000 0x03800000>, +- <0x6 0x00000000 0x6 0x00000000 0x40000000>; ++ ranges = <0x0 0x7c000000 0x0 0xfc000000 0x0 0x03800000>, ++ <0x6 0x00000000 0x6 0x00000000 0x0 0x40000000>; + + pcie0: pcie@7d500000 { + compatible = "brcm,bcm2711-pcie"; +- reg = <0x0 0x7d500000 0x9310>; ++ reg = <0x0 0x7d500000 0x0 0x9310>; + device_type = "pci"; + #address-cells = <3>; + #interrupt-cells = <1>; +@@ -503,7 +517,7 @@ pcie0: pcie@7d500000 { + + genet: ethernet@7d580000 { + compatible = "brcm,bcm2711-genet-v5"; +- reg = <0x0 0x7d580000 0x10000>; ++ reg = <0x0 0x7d580000 0x0 0x10000>; + #address-cells = <0x1>; + #size-cells = <0x1>; + interrupts = , +@@ -1010,7 +1024,7 @@ &cma { + alloc-ranges = <0x0 0x00000000 0x40000000>; + }; + +-&i2c0 { ++&i2c0if { + compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c"; + interrupts = ; + }; +diff --git a/arch/arm/boot/dts/bcm271x-rpi-bt.dtsi b/arch/arm/boot/dts/bcm271x-rpi-bt.dtsi +new file mode 100644 +index 000000000000..6b9b79f74cf3 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm271x-rpi-bt.dtsi +@@ -0,0 +1,26 @@ ++// SPDX-License-Identifier: GPL-2.0 ++ ++&uart0 { ++ bt: bluetooth { ++ compatible = "brcm,bcm43438-bt"; ++ max-speed = <3000000>; ++ shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; ++ status = "disabled"; ++ }; ++}; ++ ++&uart1 { ++ minibt: bluetooth { ++ compatible = "brcm,bcm43438-bt"; ++ max-speed = <460800>; ++ shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>; ++ status = "disabled"; ++ }; ++}; ++ ++/ { ++ __overrides__ { ++ krnbt = <&bt>,"status"; ++ krnbt_baudrate = <&bt>,"max-speed:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/bcm2835-common.dtsi b/arch/arm/boot/dts/bcm2835-common.dtsi +index 4119271c979d..bd77ba3a3562 100644 +--- a/arch/arm/boot/dts/bcm2835-common.dtsi ++++ b/arch/arm/boot/dts/bcm2835-common.dtsi +@@ -116,12 +116,14 @@ hdmi: hdmi@7e902000 { + compatible = "brcm,bcm2835-hdmi"; + reg = <0x7e902000 0x600>, + <0x7e808000 0x100>; ++ reg-names = "hdmi", ++ "hd"; + interrupts = <2 8>, <2 9>; + ddc = <&i2c2>; + clocks = <&clocks BCM2835_PLLH_PIX>, + <&clocks BCM2835_CLOCK_HSM>; + clock-names = "pixel", "hdmi"; +- dmas = <&dma 17>; ++ dmas = <&dma (17|(1<<27))>; + dma-names = "audio-rx"; + status = "disabled"; + }; +diff --git a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts +index 40b9405f1a8e..d2384d8e8555 100644 +--- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts ++++ b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts +@@ -126,3 +126,8 @@ &uart0 { + pinctrl-0 = <&uart0_gpio14>; + status = "okay"; + }; ++ ++/* i2c on camera/display connector is gpio 28&29 */ ++&i2c0mux { ++ pinctrl-1 = <&i2c0_gpio28>; ++}; +diff --git a/arch/arm/boot/dts/bcm2835-rpi-a.dts b/arch/arm/boot/dts/bcm2835-rpi-a.dts +index 11edb581dbaf..4ceca674b752 100644 +--- a/arch/arm/boot/dts/bcm2835-rpi-a.dts ++++ b/arch/arm/boot/dts/bcm2835-rpi-a.dts +@@ -121,3 +121,10 @@ &uart0 { + pinctrl-0 = <&uart0_gpio14>; + status = "okay"; + }; ++ ++/* i2c0 on camera/display connector is gpio 0&1. Not exposed on header. ++ * To avoid having to remap everything, map both ports to gpios 0&1 ++ */ ++&i2c0mux { ++ pinctrl-1 = <&i2c0_gpio0>; ++}; +diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts +index 1b435c64bd9c..8f2d10d82fa1 100644 +--- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts ++++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts +@@ -128,3 +128,8 @@ &uart0 { + pinctrl-0 = <&uart0_gpio14>; + status = "okay"; + }; ++ ++/* i2c on camera/display connector is gpio 28&29 */ ++&i2c0mux { ++ pinctrl-1 = <&i2c0_gpio28>; ++}; +diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts +index a23c25c00eea..547c88a3ae9f 100644 +--- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts ++++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts +@@ -121,3 +121,10 @@ &uart0 { + pinctrl-0 = <&uart0_gpio14>; + status = "okay"; + }; ++ ++/* i2c0 on camera/display connector is gpio 0&1. Not exposed on header. ++ * To avoid having to remap everything, map both ports to gpios 0&1 ++ */ ++&i2c0mux { ++ pinctrl-1 = <&i2c0_gpio0>; ++}; +diff --git a/arch/arm/boot/dts/bcm2835-rpi-b.dts b/arch/arm/boot/dts/bcm2835-rpi-b.dts +index 1b63d6b19750..073fc99ef8a2 100644 +--- a/arch/arm/boot/dts/bcm2835-rpi-b.dts ++++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts +@@ -116,3 +116,10 @@ &uart0 { + pinctrl-0 = <&uart0_gpio14>; + status = "okay"; + }; ++ ++/* camera/display connector use BSC1 on GPIOS 2&3. ++ * To avoid having to remap everything, map both ports to gpios 0&1 ++ */ ++&i2c0mux { ++ pinctrl-1 = <&i2c0_gpio0>; ++}; +diff --git a/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts b/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts +index a75c882e6575..95564c93a645 100644 +--- a/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts ++++ b/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts +@@ -95,3 +95,8 @@ &uart0 { + pinctrl-0 = <&uart0_gpio14>; + status = "okay"; + }; ++ ++/* WHAT TO DO HERE? */ ++&i2c0mux { ++ pinctrl-1 = <&i2c0_gpio28>; ++}; +diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts +index 33b2b77aa47d..3ea5c7e6be54 100644 +--- a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts ++++ b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts +@@ -149,3 +149,8 @@ &uart1 { + pinctrl-0 = <&uart1_gpio14>; + status = "okay"; + }; ++ ++/* i2c on camera/display connector is gpio 28&29 */ ++&i2c0mux { ++ pinctrl-1 = <&i2c0_gpio28>; ++}; +diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero.dts b/arch/arm/boot/dts/bcm2835-rpi-zero.dts +index 6f9b3a908f28..a0eabab12c99 100644 +--- a/arch/arm/boot/dts/bcm2835-rpi-zero.dts ++++ b/arch/arm/boot/dts/bcm2835-rpi-zero.dts +@@ -117,3 +117,8 @@ &uart0 { + pinctrl-0 = <&uart0_gpio14>; + status = "okay"; + }; ++ ++/* i2c on camera/display connector is gpio 28&29 */ ++&i2c0mux { ++ pinctrl-1 = <&i2c0_gpio28>; ++}; +diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi +index 87ddcad76083..1b16cb9ccb88 100644 +--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi ++++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi +@@ -19,6 +19,11 @@ firmware: firmware { + + mboxes = <&mailbox>; + dma-ranges; ++ ++ firmware_clocks: clocks { ++ compatible = "raspberrypi,firmware-clocks"; ++ #clock-cells = <1>; ++ }; + }; + + power: power { +@@ -49,13 +54,17 @@ alt0: alt0 { + }; + }; + +-&i2c0 { +- pinctrl-names = "default"; +- pinctrl-0 = <&i2c0_gpio0>; ++&i2c0if { + status = "okay"; + clock-frequency = <100000>; + }; + ++&i2c0mux { ++ pinctrl-0 = <&i2c0_gpio0>; ++ /* pinctrl-1 varies based on platform */ ++ status = "okay"; ++}; ++ + &i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_gpio2>; +diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi +index 0549686134ea..2ea891228ea0 100644 +--- a/arch/arm/boot/dts/bcm2835.dtsi ++++ b/arch/arm/boot/dts/bcm2835.dtsi +@@ -19,7 +19,7 @@ cpu@0 { + + soc { + ranges = <0x7e000000 0x20000000 0x02000000>; +- dma-ranges = <0x40000000 0x00000000 0x20000000>; ++ dma-ranges = <0x80000000 0x00000000 0x20000000>; + }; + + arm-pmu { +diff --git a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts +index d8af8eeac7b6..bf22b74359d8 100644 +--- a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts ++++ b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts +@@ -128,3 +128,8 @@ &uart0 { + pinctrl-0 = <&uart0_gpio14>; + status = "okay"; + }; ++ ++/* i2c on camera/display connector is gpio 28&29 */ ++&i2c0mux { ++ pinctrl-1 = <&i2c0_gpio28>; ++}; +diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts +index 77099a7871b0..9529c0475673 100644 +--- a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts ++++ b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts +@@ -178,3 +178,8 @@ &uart1 { + pinctrl-0 = <&uart1_gpio14>; + status = "okay"; + }; ++ ++/* i2c on camera/display connector is gpio 44&45 */ ++&i2c0mux { ++ pinctrl-1 = <&i2c0_gpio44>; ++}; +diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts +index 61010266ca9a..40cb269aed0f 100644 +--- a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts ++++ b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts +@@ -181,3 +181,8 @@ &uart1 { + pinctrl-0 = <&uart1_gpio14>; + status = "okay"; + }; ++ ++/* i2c on camera/display connector is gpio 44&45 */ ++&i2c0mux { ++ pinctrl-1 = <&i2c0_gpio44>; ++}; +diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts +index dd4a48604097..8f16b6b3fe08 100644 +--- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts ++++ b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts +@@ -174,3 +174,8 @@ &sdhost { + status = "okay"; + bus-width = <4>; + }; ++ ++/* i2c on camera/display connector is gpio 44&45 */ ++&i2c0mux { ++ pinctrl-1 = <&i2c0_gpio44>; ++}; +diff --git a/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts b/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts +index 588d9411ceb6..dde209ade51b 100644 +--- a/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts ++++ b/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts +@@ -94,3 +94,8 @@ &uart0 { + pinctrl-0 = <&uart0_gpio14>; + status = "okay"; + }; ++ ++/* WHAT TO DO HERE? */ ++&i2c0mux { ++ pinctrl-1 = <&i2c0_gpio28>; ++}; +diff --git a/arch/arm/boot/dts/bcm283x-rpi-csi0-2lane.dtsi b/arch/arm/boot/dts/bcm283x-rpi-csi0-2lane.dtsi +new file mode 100644 +index 000000000000..6e4ce8622b47 +--- /dev/null ++++ b/arch/arm/boot/dts/bcm283x-rpi-csi0-2lane.dtsi +@@ -0,0 +1,4 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++&csi0 { ++ brcm,num-data-lanes = <2>; ++}; +diff --git a/arch/arm/boot/dts/bcm283x-rpi-csi1-2lane.dtsi b/arch/arm/boot/dts/bcm283x-rpi-csi1-2lane.dtsi +new file mode 100644 +index 000000000000..6938f4daacdc +--- /dev/null ++++ b/arch/arm/boot/dts/bcm283x-rpi-csi1-2lane.dtsi +@@ -0,0 +1,4 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++&csi1 { ++ brcm,num-data-lanes = <2>; ++}; +diff --git a/arch/arm/boot/dts/bcm283x-rpi-csi1-4lane.dtsi b/arch/arm/boot/dts/bcm283x-rpi-csi1-4lane.dtsi +new file mode 100644 +index 000000000000..b37037437bee +--- /dev/null ++++ b/arch/arm/boot/dts/bcm283x-rpi-csi1-4lane.dtsi +@@ -0,0 +1,4 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++&csi1 { ++ brcm,num-data-lanes = <4>; ++}; +diff --git a/arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_28.dtsi b/arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_28.dtsi +new file mode 100644 +index 000000000000..38f0074bce3f +--- /dev/null ++++ b/arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_28.dtsi +@@ -0,0 +1,4 @@ ++&i2c0mux { ++ pinctrl-0 = <&i2c0_gpio0>; ++ pinctrl-1 = <&i2c0_gpio28>; ++}; +diff --git a/arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_44.dtsi b/arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_44.dtsi +new file mode 100644 +index 000000000000..119946d878db +--- /dev/null ++++ b/arch/arm/boot/dts/bcm283x-rpi-i2c0mux_0_44.dtsi +@@ -0,0 +1,4 @@ ++&i2c0mux { ++ pinctrl-0 = <&i2c0_gpio0>; ++ pinctrl-1 = <&i2c0_gpio44>; ++}; +diff --git a/arch/arm/boot/dts/bcm283x-rpi-usb-peripheral.dtsi b/arch/arm/boot/dts/bcm283x-rpi-usb-peripheral.dtsi +deleted file mode 100644 +index 0ff0e9e25327..000000000000 +--- a/arch/arm/boot/dts/bcm283x-rpi-usb-peripheral.dtsi ++++ /dev/null +@@ -1,7 +0,0 @@ +-// SPDX-License-Identifier: GPL-2.0 +-&usb { +- dr_mode = "peripheral"; +- g-rx-fifo-size = <256>; +- g-np-tx-fifo-size = <32>; +- g-tx-fifo-size = <256 256 512 512 512 768 768>; +-}; +diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi +index 0f3be55201a5..6d305b8b5ebe 100644 +--- a/arch/arm/boot/dts/bcm283x.dtsi ++++ b/arch/arm/boot/dts/bcm283x.dtsi +@@ -334,7 +334,7 @@ spi: spi@7e204000 { + status = "disabled"; + }; + +- i2c0: i2c@7e205000 { ++ i2c0if: i2c@7e205000 { + compatible = "brcm,bcm2835-i2c"; + reg = <0x7e205000 0x200>; + interrupts = <2 21>; +@@ -344,6 +344,30 @@ i2c0: i2c@7e205000 { + status = "disabled"; + }; + ++ i2c0mux: i2c0mux { ++ compatible = "i2c-mux-pinctrl"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ i2c-parent = <&i2c0if>; ++ ++ pinctrl-names = "i2c0", "i2c_csi_dsi"; ++ ++ status = "disabled"; ++ ++ i2c0: i2c@0 { ++ reg = <0>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ }; ++ ++ i2c_csi_dsi: i2c@1 { ++ reg = <1>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ }; ++ }; ++ + dpi: dpi@7e208000 { + compatible = "brcm,bcm2835-dpi"; + reg = <0x7e208000 0x8c>; +diff --git a/arch/arm/boot/dts/overlays/Makefile b/arch/arm/boot/dts/overlays/Makefile +new file mode 100644 +index 000000000000..b30568e29526 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/Makefile +@@ -0,0 +1,216 @@ ++# Overlays for the Raspberry Pi platform ++ ++dtb-$(CONFIG_ARCH_BCM2835) += overlay_map.dtb ++ ++dtbo-$(CONFIG_ARCH_BCM2835) += \ ++ act-led.dtbo \ ++ adafruit18.dtbo \ ++ adau1977-adc.dtbo \ ++ adau7002-simple.dtbo \ ++ ads1015.dtbo \ ++ ads1115.dtbo \ ++ ads7846.dtbo \ ++ adv7282m.dtbo \ ++ adv728x-m.dtbo \ ++ akkordion-iqdacplus.dtbo \ ++ allo-boss-dac-pcm512x-audio.dtbo \ ++ allo-digione.dtbo \ ++ allo-katana-dac-audio.dtbo \ ++ allo-piano-dac-pcm512x-audio.dtbo \ ++ allo-piano-dac-plus-pcm512x-audio.dtbo \ ++ anyspi.dtbo \ ++ apds9960.dtbo \ ++ applepi-dac.dtbo \ ++ at86rf233.dtbo \ ++ audioinjector-addons.dtbo \ ++ audioinjector-isolated-soundcard.dtbo \ ++ audioinjector-ultra.dtbo \ ++ audioinjector-wm8731-audio.dtbo \ ++ audiosense-pi.dtbo \ ++ audremap.dtbo \ ++ balena-fin.dtbo \ ++ cma.dtbo \ ++ dht11.dtbo \ ++ dionaudio-loco.dtbo \ ++ dionaudio-loco-v2.dtbo \ ++ disable-bt.dtbo \ ++ disable-wifi.dtbo \ ++ dpi18.dtbo \ ++ dpi24.dtbo \ ++ draws.dtbo \ ++ dwc-otg.dtbo \ ++ dwc2.dtbo \ ++ enc28j60.dtbo \ ++ enc28j60-spi2.dtbo \ ++ exc3000.dtbo \ ++ fe-pi-audio.dtbo \ ++ fsm-demo.dtbo \ ++ ghost-amp.dtbo \ ++ goodix.dtbo \ ++ googlevoicehat-soundcard.dtbo \ ++ gpio-fan.dtbo \ ++ gpio-ir.dtbo \ ++ gpio-ir-tx.dtbo \ ++ gpio-key.dtbo \ ++ gpio-no-bank0-irq.dtbo \ ++ gpio-no-irq.dtbo \ ++ gpio-poweroff.dtbo \ ++ gpio-shutdown.dtbo \ ++ hd44780-lcd.dtbo \ ++ hdmi-backlight-hwhack-gpio.dtbo \ ++ hifiberry-amp.dtbo \ ++ hifiberry-dac.dtbo \ ++ hifiberry-dacplus.dtbo \ ++ hifiberry-dacplusadc.dtbo \ ++ hifiberry-dacplusadcpro.dtbo \ ++ hifiberry-dacplusdsp.dtbo \ ++ hifiberry-dacplushd.dtbo \ ++ hifiberry-digi.dtbo \ ++ hifiberry-digi-pro.dtbo \ ++ highperi.dtbo \ ++ hy28a.dtbo \ ++ hy28b.dtbo \ ++ hy28b-2017.dtbo \ ++ i-sabre-q2m.dtbo \ ++ i2c-bcm2708.dtbo \ ++ i2c-gpio.dtbo \ ++ i2c-mux.dtbo \ ++ i2c-pwm-pca9685a.dtbo \ ++ i2c-rtc.dtbo \ ++ i2c-rtc-gpio.dtbo \ ++ i2c-sensor.dtbo \ ++ i2c0.dtbo \ ++ i2c1.dtbo \ ++ i2c3.dtbo \ ++ i2c4.dtbo \ ++ i2c5.dtbo \ ++ i2c6.dtbo \ ++ i2s-gpio28-31.dtbo \ ++ ilitek251x.dtbo \ ++ imx219.dtbo \ ++ imx290.dtbo \ ++ imx477.dtbo \ ++ iqaudio-codec.dtbo \ ++ iqaudio-dac.dtbo \ ++ iqaudio-dacplus.dtbo \ ++ iqaudio-digi-wm8804-audio.dtbo \ ++ irs1125.dtbo \ ++ jedec-spi-nor.dtbo \ ++ justboom-both.dtbo \ ++ justboom-dac.dtbo \ ++ justboom-digi.dtbo \ ++ ltc294x.dtbo \ ++ max98357a.dtbo \ ++ maxtherm.dtbo \ ++ mbed-dac.dtbo \ ++ mcp23017.dtbo \ ++ mcp23s17.dtbo \ ++ mcp2515-can0.dtbo \ ++ mcp2515-can1.dtbo \ ++ mcp3008.dtbo \ ++ mcp3202.dtbo \ ++ mcp342x.dtbo \ ++ media-center.dtbo \ ++ merus-amp.dtbo \ ++ midi-uart0.dtbo \ ++ midi-uart1.dtbo \ ++ miniuart-bt.dtbo \ ++ mmc.dtbo \ ++ mpu6050.dtbo \ ++ mz61581.dtbo \ ++ ov5647.dtbo \ ++ ov7251.dtbo \ ++ ov9281.dtbo \ ++ papirus.dtbo \ ++ pca953x.dtbo \ ++ pibell.dtbo \ ++ pifacedigital.dtbo \ ++ piglow.dtbo \ ++ piscreen.dtbo \ ++ piscreen2r.dtbo \ ++ pisound.dtbo \ ++ pitft22.dtbo \ ++ pitft28-capacitive.dtbo \ ++ pitft28-resistive.dtbo \ ++ pitft35-resistive.dtbo \ ++ pps-gpio.dtbo \ ++ pwm.dtbo \ ++ pwm-2chan.dtbo \ ++ pwm-ir-tx.dtbo \ ++ qca7000.dtbo \ ++ rotary-encoder.dtbo \ ++ rpi-backlight.dtbo \ ++ rpi-cirrus-wm5102.dtbo \ ++ rpi-dac.dtbo \ ++ rpi-display.dtbo \ ++ rpi-ft5406.dtbo \ ++ rpi-poe.dtbo \ ++ rpi-proto.dtbo \ ++ rpi-sense.dtbo \ ++ rpi-tv.dtbo \ ++ rpivid-v4l2.dtbo \ ++ rra-digidac1-wm8741-audio.dtbo \ ++ sainsmart18.dtbo \ ++ sc16is750-i2c.dtbo \ ++ sc16is752-i2c.dtbo \ ++ sc16is752-spi0.dtbo \ ++ sc16is752-spi1.dtbo \ ++ sdhost.dtbo \ ++ sdio.dtbo \ ++ sdtweak.dtbo \ ++ sh1106-spi.dtbo \ ++ smi.dtbo \ ++ smi-dev.dtbo \ ++ smi-nand.dtbo \ ++ spi-gpio35-39.dtbo \ ++ spi-gpio40-45.dtbo \ ++ spi-rtc.dtbo \ ++ spi0-1cs.dtbo \ ++ spi0-2cs.dtbo \ ++ spi1-1cs.dtbo \ ++ spi1-2cs.dtbo \ ++ spi1-3cs.dtbo \ ++ spi2-1cs.dtbo \ ++ spi2-2cs.dtbo \ ++ spi2-3cs.dtbo \ ++ spi3-1cs.dtbo \ ++ spi3-2cs.dtbo \ ++ spi4-1cs.dtbo \ ++ spi4-2cs.dtbo \ ++ spi5-1cs.dtbo \ ++ spi5-2cs.dtbo \ ++ spi6-1cs.dtbo \ ++ spi6-2cs.dtbo \ ++ ssd1306.dtbo \ ++ ssd1306-spi.dtbo \ ++ ssd1351-spi.dtbo \ ++ superaudioboard.dtbo \ ++ sx150x.dtbo \ ++ tc358743.dtbo \ ++ tc358743-audio.dtbo \ ++ tinylcd35.dtbo \ ++ tpm-slb9670.dtbo \ ++ uart0.dtbo \ ++ uart1.dtbo \ ++ uart2.dtbo \ ++ uart3.dtbo \ ++ uart4.dtbo \ ++ uart5.dtbo \ ++ udrc.dtbo \ ++ upstream.dtbo \ ++ upstream-pi4.dtbo \ ++ vc4-fkms-v3d.dtbo \ ++ vc4-kms-kippah-7inch.dtbo \ ++ vc4-kms-v3d.dtbo \ ++ vc4-kms-v3d-pi4.dtbo \ ++ vga666.dtbo \ ++ w1-gpio.dtbo \ ++ w1-gpio-pullup.dtbo \ ++ w5500.dtbo \ ++ wittypi.dtbo ++ ++targets += dtbs dtbs_install ++targets += $(dtbo-y) ++ ++always-y := $(dtbo-y) ++clean-files := *.dtbo +diff --git a/arch/arm/boot/dts/overlays/README b/arch/arm/boot/dts/overlays/README +new file mode 100644 +index 000000000000..eff90baed406 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/README +@@ -0,0 +1,3040 @@ ++Introduction ++============ ++ ++This directory contains Device Tree overlays. Device Tree makes it possible ++to support many hardware configurations with a single kernel and without the ++need to explicitly load or blacklist kernel modules. Note that this isn't a ++"pure" Device Tree configuration (c.f. MACH_BCM2835) - some on-board devices ++are still configured by the board support code, but the intention is to ++eventually reach that goal. ++ ++On Raspberry Pi, Device Tree usage is controlled from /boot/config.txt. By ++default, the Raspberry Pi kernel boots with device tree enabled. You can ++completely disable DT usage (for now) by adding: ++ ++ device_tree= ++ ++to your config.txt, which should cause your Pi to revert to the old way of ++doing things after a reboot. ++ ++In /boot you will find a .dtb for each base platform. This describes the ++hardware that is part of the Raspberry Pi board. The loader (start.elf and its ++siblings) selects the .dtb file appropriate for the platform by name, and reads ++it into memory. At this point, all of the optional interfaces (i2c, i2s, spi) ++are disabled, but they can be enabled using Device Tree parameters: ++ ++ dtparam=i2c=on,i2s=on,spi=on ++ ++However, this shouldn't be necessary in many use cases because loading an ++overlay that requires one of those interfaces will cause it to be enabled ++automatically, and it is advisable to only enable interfaces if they are ++needed. ++ ++Configuring additional, optional hardware is done using Device Tree overlays ++(see below). ++ ++GPIO numbering uses the hardware pin numbering scheme (aka BCM scheme) and ++not the physical pin numbers. ++ ++raspi-config ++============ ++ ++The Advanced Options section of the raspi-config utility can enable and disable ++Device Tree use, as well as toggling the I2C and SPI interfaces. Note that it ++is possible to both enable an interface and blacklist the driver, if for some ++reason you should want to defer the loading. ++ ++Modules ++======= ++ ++As well as describing the hardware, Device Tree also gives enough information ++to allow suitable driver modules to be located and loaded, with the corollary ++that unneeded modules are not loaded. As a result it should be possible to ++remove lines from /etc/modules, and /etc/modprobe.d/raspi-blacklist.conf can ++have its contents deleted (or commented out). ++ ++Using Overlays ++============== ++ ++Overlays are loaded using the "dtoverlay" config.txt setting. As an example, ++consider I2C Real Time Clock drivers. In the pre-DT world these would be loaded ++by writing a magic string comprising a device identifier and an I2C address to ++a special file in /sys/class/i2c-adapter, having first loaded the driver for ++the I2C interface and the RTC device - something like this: ++ ++ modprobe i2c-bcm2835 ++ modprobe rtc-ds1307 ++ echo ds1307 0x68 > /sys/class/i2c-adapter/i2c-1/new_device ++ ++With DT enabled, this becomes a line in config.txt: ++ ++ dtoverlay=i2c-rtc,ds1307 ++ ++This causes the file /boot/overlays/i2c-rtc.dtbo to be loaded and a "node" ++describing the DS1307 I2C device to be added to the Device Tree for the Pi. By ++default it usees address 0x68, but this can be modified with an additional DT ++parameter: ++ ++ dtoverlay=i2c-rtc,ds1307,addr=0x68 ++ ++Parameters usually have default values, although certain parameters are ++mandatory. See the list of overlays below for a description of the parameters ++and their defaults. ++ ++The Overlay and Parameter Reference ++=================================== ++ ++N.B. When editing this file, please preserve the indentation levels to make it ++simple to parse programmatically. NO HARD TABS. ++ ++ ++Name: ++Info: Configures the base Raspberry Pi hardware ++Load: ++Params: ++ ant1 Select antenna 1 (default). CM4 only. ++ ++ ant2 Select antenna 2. CM4 only. ++ ++ noant Disable both antennas. CM4 only. ++ ++ audio Set to "on" to enable the onboard ALSA audio ++ interface (default "off") ++ ++ axiperf Set to "on" to enable the AXI bus performance ++ monitors. ++ See /sys/kernel/debug/raspberrypi_axi_monitor ++ for the results. ++ ++ eee Enable Energy Efficient Ethernet support for ++ compatible devices (default "on"). See also ++ "tx_lpi_timer". Pi3B+ only. ++ ++ eth_downshift_after Set the number of auto-negotiation failures ++ after which the 1000Mbps modes are disabled. ++ Legal values are 2, 3, 4, 5 and 0, where ++ 0 means never downshift (default 2). Pi3B+ only. ++ ++ eth_led0 Set mode of LED0 - amber on Pi3B+ (default "1"), ++ green on Pi4 (default "0"). ++ The legal values are: ++ ++ Pi3B+ ++ ++ 0=link/activity 1=link1000/activity ++ 2=link100/activity 3=link10/activity ++ 4=link100/1000/activity 5=link10/1000/activity ++ 6=link10/100/activity 14=off 15=on ++ ++ Pi4 ++ ++ 0=Speed/Activity 1=Speed ++ 2=Flash activity 3=FDX ++ 4=Off 5=On ++ 6=Alt 7=Speed/Flash ++ 8=Link 9=Activity ++ ++ eth_led1 Set mode of LED1 - green on Pi3B+ (default "6"), ++ amber on Pi4 (default "8"). See eth_led0 for ++ legal values. ++ ++ eth_max_speed Set the maximum speed a link is allowed ++ to negotiate. Legal values are 10, 100 and ++ 1000 (default 1000). Pi3B+ only. ++ ++ i2c_arm Set to "on" to enable the ARM's i2c interface ++ (default "off") ++ ++ i2c_vc Set to "on" to enable the i2c interface ++ usually reserved for the VideoCore processor ++ (default "off") ++ ++ i2c An alias for i2c_arm ++ ++ i2c_arm_baudrate Set the baudrate of the ARM's i2c interface ++ (default "100000") ++ ++ i2c_vc_baudrate Set the baudrate of the VideoCore i2c interface ++ (default "100000") ++ ++ i2c_baudrate An alias for i2c_arm_baudrate ++ ++ i2s Set to "on" to enable the i2s interface ++ (default "off") ++ ++ krnbt Set to "on" to enable autoprobing of Bluetooth ++ driver without need of hciattach/btattach ++ (default "off") ++ ++ krnbt_baudrate Set the baudrate of the PL011 UART when used ++ with krnbt=on ++ ++ spi Set to "on" to enable the spi interfaces ++ (default "off") ++ ++ spi_dma4 Use to enable 40-bit DMA on spi interfaces ++ (the assigned value doesn't matter) ++ (2711 only) ++ ++ random Set to "on" to enable the hardware random ++ number generator (default "on") ++ ++ sd_overclock Clock (in MHz) to use when the MMC framework ++ requests 50MHz ++ ++ sd_poll_once Looks for a card once after booting. Useful ++ for network booting scenarios to avoid the ++ overhead of continuous polling. N.B. Using ++ this option restricts the system to using a ++ single card per boot (or none at all). ++ (default off) ++ ++ sd_force_pio Disable DMA support for SD driver (default off) ++ ++ sd_pio_limit Number of blocks above which to use DMA for ++ SD card (default 1) ++ ++ sd_debug Enable debug output from SD driver (default off) ++ ++ sdio_overclock Clock (in MHz) to use when the MMC framework ++ requests 50MHz for the SDIO/WiFi interface. ++ ++ tx_lpi_timer Set the delay in microseconds between going idle ++ and entering the low power state (default 600). ++ Requires EEE to be enabled - see "eee". ++ ++ uart0 Set to "off" to disable uart0 (default "on") ++ ++ uart1 Set to "on" or "off" to enable or disable uart1 ++ (default varies) ++ ++ watchdog Set to "on" to enable the hardware watchdog ++ (default "off") ++ ++ act_led_trigger Choose which activity the LED tracks. ++ Use "heartbeat" for a nice load indicator. ++ (default "mmc") ++ ++ act_led_activelow Set to "on" to invert the sense of the LED ++ (default "off") ++ N.B. For Pi 3B, 3B+, 3A+ and 4B, use the act-led ++ overlay. ++ ++ act_led_gpio Set which GPIO to use for the activity LED ++ (in case you want to connect it to an external ++ device) ++ (default "16" on a non-Plus board, "47" on a ++ Plus or Pi 2) ++ N.B. For Pi 3B, 3B+, 3A+ and 4B, use the act-led ++ overlay. ++ ++ pwr_led_trigger ++ pwr_led_activelow ++ pwr_led_gpio ++ As for act_led_*, but using the PWR LED. ++ Not available on Model A/B boards. ++ ++ N.B. It is recommended to only enable those interfaces that are needed. ++ Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc ++ interfering with Pi Camera, I2S and SPI hogging GPIO pins, etc.) ++ Note also that i2c, i2c_arm and i2c_vc are aliases for the physical ++ interfaces i2c0 and i2c1. Use of the numeric variants is still possible ++ but deprecated because the ARM/VC assignments differ between board ++ revisions. The same board-specific mapping applies to i2c_baudrate, ++ and the other i2c baudrate parameters. ++ ++ ++Name: act-led ++Info: Pi 3B, 3B+, 3A+ and 4B use a GPIO expander to drive the LEDs which can ++ only be accessed from the VPU. There is a special driver for this with a ++ separate DT node, which has the unfortunate consequence of breaking the ++ act_led_gpio and act_led_activelow dtparams. ++ This overlay changes the GPIO controller back to the standard one and ++ restores the dtparams. ++Load: dtoverlay=act-led,= ++Params: activelow Set to "on" to invert the sense of the LED ++ (default "off") ++ ++ gpio Set which GPIO to use for the activity LED ++ (in case you want to connect it to an external ++ device) ++ REQUIRED ++ ++ ++Name: adafruit18 ++Info: Overlay for the SPI-connected Adafruit 1.8" display (based on the ++ ST7735R chip). It includes support for the "green tab" version. ++Load: dtoverlay=adafruit18,= ++Params: green Use the adafruit18_green variant. ++ rotate Display rotation {0,90,180,270} ++ speed SPI bus speed in Hz (default 4000000) ++ fps Display frame rate in Hz ++ bgr Enable BGR mode (default off) ++ debug Debug output level {0-7} ++ dc_pin GPIO pin for D/C (default 24) ++ reset_pin GPIO pin for RESET (default 25) ++ led_pin GPIO used to control backlight (default 18) ++ ++ ++Name: adau1977-adc ++Info: Overlay for activation of ADAU1977 ADC codec over I2C for control ++ and I2S for data. ++Load: dtoverlay=adau1977-adc ++Params: ++ ++ ++Name: adau7002-simple ++Info: Overlay for the activation of ADAU7002 stereo PDM to I2S converter. ++Load: dtoverlay=adau7002-simple,= ++Params: card-name Override the default, "adau7002", card name. ++ ++ ++Name: ads1015 ++Info: Overlay for activation of Texas Instruments ADS1015 ADC over I2C ++Load: dtoverlay=ads1015,= ++Params: addr I2C bus address of device. Set based on how the ++ addr pin is wired. (default=0x48 assumes addr ++ is pulled to GND) ++ cha_enable Enable virtual channel a. (default=true) ++ cha_cfg Set the configuration for virtual channel a. ++ (default=4 configures this channel for the ++ voltage at A0 with respect to GND) ++ cha_datarate Set the datarate (samples/sec) for this channel. ++ (default=4 sets 1600 sps) ++ cha_gain Set the gain of the Programmable Gain ++ Amplifier for this channel. (default=2 sets the ++ full scale of the channel to 2.048 Volts) ++ ++ Channel (ch) parameters can be set for each enabled channel. ++ A maximum of 4 channels can be enabled (letters a thru d). ++ For more information refer to the device datasheet at: ++ http://www.ti.com/lit/ds/symlink/ads1015.pdf ++ ++ ++Name: ads1115 ++Info: Texas Instruments ADS1115 ADC ++Load: dtoverlay=ads1115,[=] ++Params: addr I2C bus address of device. Set based on how the ++ addr pin is wired. (default=0x48 assumes addr ++ is pulled to GND) ++ cha_enable Enable virtual channel a. ++ cha_cfg Set the configuration for virtual channel a. ++ (default=4 configures this channel for the ++ voltage at A0 with respect to GND) ++ cha_datarate Set the datarate (samples/sec) for this channel. ++ (default=7 sets 860 sps) ++ cha_gain Set the gain of the Programmable Gain ++ Amplifier for this channel. (Default 1 sets the ++ full scale of the channel to 4.096 Volts) ++ ++ Channel parameters can be set for each enabled channel. ++ A maximum of 4 channels can be enabled (letters a thru d). ++ For more information refer to the device datasheet at: ++ http://www.ti.com/lit/ds/symlink/ads1115.pdf ++ ++ ++Name: ads7846 ++Info: ADS7846 Touch controller ++Load: dtoverlay=ads7846,= ++Params: cs SPI bus Chip Select (default 1) ++ speed SPI bus speed (default 2MHz, max 3.25MHz) ++ penirq GPIO used for PENIRQ. REQUIRED ++ penirq_pull Set GPIO pull (default 0=none, 2=pullup) ++ swapxy Swap x and y axis ++ xmin Minimum value on the X axis (default 0) ++ ymin Minimum value on the Y axis (default 0) ++ xmax Maximum value on the X axis (default 4095) ++ ymax Maximum value on the Y axis (default 4095) ++ pmin Minimum reported pressure value (default 0) ++ pmax Maximum reported pressure value (default 65535) ++ xohms Touchpanel sensitivity (X-plate resistance) ++ (default 400) ++ ++ penirq is required and usually xohms (60-100) has to be set as well. ++ Apart from that, pmax (255) and swapxy are also common. ++ The rest of the calibration can be done with xinput-calibrator. ++ See: github.com/notro/fbtft/wiki/FBTFT-on-Raspian ++ Device Tree binding document: ++ www.kernel.org/doc/Documentation/devicetree/bindings/input/ads7846.txt ++ ++ ++Name: adv7282m ++Info: Analog Devices ADV7282M analogue video to CSI2 bridge. ++ Uses Unicam1, which is the standard camera connector on most Pi ++ variants. ++Load: dtoverlay=adv7282m,= ++Params: addr Overrides the I2C address (default 0x21) ++ ++ ++Name: adv728x-m ++Info: Analog Devices ADV728[0|1|2]-M analogue video to CSI2 bridges. ++ This is a wrapper for adv7282m, and defaults to ADV7282M. ++Load: dtoverlay=adv728x-m,= ++Params: addr Overrides the I2C address (default 0x21) ++ adv7280m Select ADV7280-M. ++ adv7281m Select ADV7281-M. ++ adv7281ma Select ADV7281-MA. ++ ++ ++Name: akkordion-iqdacplus ++Info: Configures the Digital Dreamtime Akkordion Music Player (based on the ++ OEM IQAudIO DAC+ or DAC Zero module). ++Load: dtoverlay=akkordion-iqdacplus,= ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ dtoverlay=akkordion-iqdacplus,24db_digital_gain ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24db_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ ++ ++Name: allo-boss-dac-pcm512x-audio ++Info: Configures the Allo Boss DAC audio cards. ++Load: dtoverlay=allo-boss-dac-pcm512x-audio, ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ "dtoverlay=allo-boss-dac-pcm512x-audio, ++ 24db_digital_gain" ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24db_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ slave Force Boss DAC into slave mode, using Pi a ++ master for bit clock and frame clock. Enable ++ with "dtoverlay=allo-boss-dac-pcm512x-audio, ++ slave" ++ ++ ++Name: allo-digione ++Info: Configures the Allo Digione audio card ++Load: dtoverlay=allo-digione ++Params: ++ ++ ++Name: allo-katana-dac-audio ++Info: Configures the Allo Katana DAC audio card ++Load: dtoverlay=allo-katana-dac-audio ++Params: ++ ++ ++Name: allo-piano-dac-pcm512x-audio ++Info: Configures the Allo Piano DAC (2.0/2.1) audio cards. ++ (NB. This initial support is for 2.0 channel audio ONLY! ie. stereo. ++ The subwoofer outputs on the Piano 2.1 are not currently supported!) ++Load: dtoverlay=allo-piano-dac-pcm512x-audio, ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24db_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ ++ ++Name: allo-piano-dac-plus-pcm512x-audio ++Info: Configures the Allo Piano DAC (2.1) audio cards. ++Load: dtoverlay=allo-piano-dac-plus-pcm512x-audio, ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24db_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ glb_mclk This option is only with Kali board. If enabled, ++ MCLK for Kali is used and PLL is disabled for ++ better voice quality. (default Off) ++ ++ ++Name: anyspi ++Info: Universal device tree overlay for SPI devices ++ ++ Just specify the SPI address and device name ("compatible" property). ++ This overlay lacks any device-specific parameter support! ++ ++ For devices on spi1 or spi2, the interfaces should be enabled ++ with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays. ++ ++ Examples: ++ 1. SPI NOR flash on spi0.1, maximum SPI clock frequency 45MHz: ++ dtoverlay=anyspi:spi0-1,dev="jedec,spi-nor",speed=45000000 ++ 2. MCP3204 ADC on spi1.2, maximum SPI clock frequency 500kHz: ++ dtoverlay=anyspi:spi1-2,dev="microchip,mcp3204" ++Load: dtoverlay=anyspi,= ++Params: spi- Configure device at spi, cs ++ (boolean, required) ++ dev Set device name to search compatible module ++ (string, required) ++ speed Set SPI clock frequency in Hz ++ (integer, optional, default 500000) ++ ++ ++Name: apds9960 ++Info: Configures the AVAGO APDS9960 digital proximity, ambient light, RGB and ++ gesture sensor ++Load: dtoverlay=apds9960,= ++Params: gpiopin GPIO used for INT (default 4) ++ noints Disable the interrupt GPIO line. ++ ++ ++Name: applepi-dac ++Info: Configures the Orchard Audio ApplePi-DAC audio card ++Load: dtoverlay=applepi-dac ++Params: ++ ++ ++Name: at86rf233 ++Info: Configures the Atmel AT86RF233 802.15.4 low-power WPAN transceiver, ++ connected to spi0.0 ++Load: dtoverlay=at86rf233,= ++Params: interrupt GPIO used for INT (default 23) ++ reset GPIO used for Reset (default 24) ++ sleep GPIO used for Sleep (default 25) ++ speed SPI bus speed in Hz (default 3000000) ++ trim Fine tuning of the internal capacitance ++ arrays (0=+0pF, 15=+4.5pF, default 15) ++ ++ ++Name: audioinjector-addons ++Info: Configures the audioinjector.net audio add on soundcards ++Load: dtoverlay=audioinjector-addons,= ++Params: non-stop-clocks Keeps the clocks running even when the stream ++ is paused or stopped (default off) ++ ++ ++Name: audioinjector-isolated-soundcard ++Info: Configures the audioinjector.net isolated soundcard ++Load: dtoverlay=audioinjector-isolated-soundcard ++Params: ++ ++ ++Name: audioinjector-ultra ++Info: Configures the audioinjector.net ultra soundcard ++Load: dtoverlay=audioinjector-ultra ++Params: ++ ++ ++Name: audioinjector-wm8731-audio ++Info: Configures the audioinjector.net audio add on soundcard ++Load: dtoverlay=audioinjector-wm8731-audio ++Params: ++ ++ ++Name: audiosense-pi ++Info: Configures the audiosense-pi add on soundcard ++ For more information refer to ++ https://gitlab.com/kakar0t/audiosense-pi ++Load: dtoverlay=audiosense-pi ++Params: ++ ++ ++Name: audremap ++Info: Switches PWM sound output to GPIOs on the 40-pin header ++Load: dtoverlay=audremap,= ++Params: swap_lr Reverse the channel allocation, which will also ++ swap the audio jack outputs (default off) ++ enable_jack Don't switch off the audio jack output ++ (default off) ++ pins_12_13 Select GPIOs 12 & 13 (default) ++ pins_18_19 Select GPIOs 18 & 19 ++ ++ ++Name: balena-fin ++Info: Overlay that enables WiFi, Bluetooth and the GPIO expander on the ++ balenaFin carrier board for the Raspberry Pi Compute Module 3/3+ Lite. ++Load: dtoverlay=balena-fin ++Params: ++ ++ ++Name: bmp085_i2c-sensor ++Info: This overlay is now deprecated - see i2c-sensor ++Load: ++ ++ ++Name: cma ++Info: Set custom CMA sizes, only use if you know what you are doing, might ++ clash with other overlays like vc4-fkms-v3d and vc4-kms-v3d. ++Load: dtoverlay=cma,= ++Params: cma-512 CMA is 512MB (needs 1GB) ++ cma-448 CMA is 448MB (needs 1GB) ++ cma-384 CMA is 384MB (needs 1GB) ++ cma-320 CMA is 320MB (needs 1GB) ++ cma-256 CMA is 256MB (needs 1GB) ++ cma-192 CMA is 192MB (needs 1GB) ++ cma-128 CMA is 128MB ++ cma-96 CMA is 96MB ++ cma-64 CMA is 64MB ++ cma-size CMA size in bytes, 4MB aligned ++ cma-default Use upstream's default value ++ ++ ++Name: dht11 ++Info: Overlay for the DHT11/DHT21/DHT22 humidity/temperature sensors ++ Also sometimes found with the part number(s) AM230x. ++Load: dtoverlay=dht11,= ++Params: gpiopin GPIO connected to the sensor's DATA output. ++ (default 4) ++ ++ ++Name: dionaudio-loco ++Info: Configures the Dion Audio LOCO DAC-AMP ++Load: dtoverlay=dionaudio-loco ++Params: ++ ++ ++Name: dionaudio-loco-v2 ++Info: Configures the Dion Audio LOCO-V2 DAC-AMP ++Load: dtoverlay=dionaudio-loco-v2,= ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ "dtoverlay=hifiberry-dacplus,24db_digital_gain" ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24dB_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ ++ ++Name: disable-bt ++Info: Disable onboard Bluetooth on Pi 3B, 3B+, 3A+, 4B and Zero W, restoring ++ UART0/ttyAMA0 over GPIOs 14 & 15. ++ N.B. To disable the systemd service that initialises the modem so it ++ doesn't use the UART, use 'sudo systemctl disable hciuart'. ++Load: dtoverlay=disable-bt ++Params: ++ ++ ++Name: disable-wifi ++Info: Disable onboard WiFi on Pi 3B, 3B+, 3A+, 4B and Zero W. ++Load: dtoverlay=disable-wifi ++Params: ++ ++ ++Name: dpi18 ++Info: Overlay for a generic 18-bit DPI display ++ This uses GPIOs 0-21 (so no I2C, uart etc.), and activates the output ++ 2-3 seconds after the kernel has started. ++Load: dtoverlay=dpi18 ++Params: ++ ++ ++Name: dpi24 ++Info: Overlay for a generic 24-bit DPI display ++ This uses GPIOs 0-27 (so no I2C, uart etc.), and activates the output ++ 2-3 seconds after the kernel has started. ++Load: dtoverlay=dpi24 ++Params: ++ ++ ++Name: draws ++Info: Configures the NW Digital Radio DRAWS Hat ++ ++ The board includes an ADC to measure various board values and also ++ provides two analog user inputs on the expansion header. The ADC ++ can be configured for various sample rates and gain values to adjust ++ the input range. Tables describing the two parameters follow. ++ ++ ADC Gain Values: ++ 0 = +/- 6.144V ++ 1 = +/- 4.096V ++ 2 = +/- 2.048V ++ 3 = +/- 1.024V ++ 4 = +/- 0.512V ++ 5 = +/- 0.256V ++ 6 = +/- 0.256V ++ 7 = +/- 0.256V ++ ++ ADC Datarate Values: ++ 0 = 128sps ++ 1 = 250sps ++ 2 = 490sps ++ 3 = 920sps ++ 4 = 1600sps (default) ++ 5 = 2400sps ++ 6 = 3300sps ++ 7 = 3300sps ++Load: dtoverlay=draws,= ++Params: draws_adc_ch4_gain Sets the full scale resolution of the ADCs ++ input voltage sensor (default 1) ++ ++ draws_adc_ch4_datarate Sets the datarate of the ADCs input voltage ++ sensor ++ ++ draws_adc_ch5_gain Sets the full scale resolution of the ADCs ++ 5V rail voltage sensor (default 1) ++ ++ draws_adc_ch5_datarate Sets the datarate of the ADCs 4V rail voltage ++ sensor ++ ++ draws_adc_ch6_gain Sets the full scale resolution of the ADCs ++ AIN2 input (default 2) ++ ++ draws_adc_ch6_datarate Sets the datarate of the ADCs AIN2 input ++ ++ draws_adc_ch7_gain Sets the full scale resolution of the ADCs ++ AIN3 input (default 2) ++ ++ draws_adc_ch7_datarate Sets the datarate of the ADCs AIN3 input ++ ++ alsaname Name of the ALSA audio device (default "draws") ++ ++ ++Name: dwc-otg ++Info: Selects the dwc_otg USB controller driver which has fiq support. This ++ is the default on all except the Pi Zero which defaults to dwc2. ++Load: dtoverlay=dwc-otg ++Params: ++ ++ ++Name: dwc2 ++Info: Selects the dwc2 USB controller driver ++Load: dtoverlay=dwc2,= ++Params: dr_mode Dual role mode: "host", "peripheral" or "otg" ++ ++ g-rx-fifo-size Size of rx fifo size in gadget mode ++ ++ g-np-tx-fifo-size Size of non-periodic tx fifo size in gadget ++ mode ++ ++ ++[ The ds1307-rtc overlay has been deleted. See i2c-rtc. ] ++ ++ ++Name: enc28j60 ++Info: Overlay for the Microchip ENC28J60 Ethernet Controller on SPI0 ++Load: dtoverlay=enc28j60,= ++Params: int_pin GPIO used for INT (default 25) ++ ++ speed SPI bus speed (default 12000000) ++ ++ ++Name: enc28j60-spi2 ++Info: Overlay for the Microchip ENC28J60 Ethernet Controller on SPI2 ++Load: dtoverlay=enc28j60-spi2,= ++Params: int_pin GPIO used for INT (default 39) ++ ++ speed SPI bus speed (default 12000000) ++ ++ ++Name: exc3000 ++Info: Enables I2C connected EETI EXC3000 multiple touch controller using ++ GPIO 4 (pin 7 on GPIO header) for interrupt. ++Load: dtoverlay=exc3000,= ++Params: interrupt GPIO used for interrupt (default 4) ++ sizex Touchscreen size x (default 4096) ++ sizey Touchscreen size y (default 4096) ++ invx Touchscreen inverted x axis ++ invy Touchscreen inverted y axis ++ swapxy Touchscreen swapped x y axis ++ ++ ++Name: fe-pi-audio ++Info: Configures the Fe-Pi Audio Sound Card ++Load: dtoverlay=fe-pi-audio ++Params: ++ ++ ++Name: fsm-demo ++Info: A demonstration of the gpio-fsm driver. The GPIOs are chosen to work ++ nicely with a "traffic-light" display of red, amber and green LEDs on ++ GPIOs 7, 8 and 25 respectively. ++Load: dtoverlay=fsm-demo,= ++Params: fsm_debug Enable debug logging (default off) ++ ++ ++Name: ghost-amp ++Info: An overlay for the Ghost amplifier. ++Load: dtoverlay=ghost-amp,= ++Params: fsm_debug Enable debug logging of the GPIO FSM (default ++ off) ++ ++ ++Name: goodix ++Info: Enables I2C connected Goodix gt9271 multiple touch controller using ++ GPIOs 4 and 17 (pins 7 and 11 on GPIO header) for interrupt and reset. ++Load: dtoverlay=goodix,= ++Params: interrupt GPIO used for interrupt (default 4) ++ reset GPIO used for reset (default 17) ++ ++ ++Name: googlevoicehat-soundcard ++Info: Configures the Google voiceHAT soundcard ++Load: dtoverlay=googlevoicehat-soundcard ++Params: ++ ++ ++Name: gpio-fan ++Info: Configure a GPIO pin to control a cooling fan. ++Load: dtoverlay=gpio-fan,= ++Params: gpiopin GPIO used to control the fan (default 12) ++ temp Temperature at which the fan switches on, in ++ millicelcius (default 55000) ++ ++ ++Name: gpio-ir ++Info: Use GPIO pin as rc-core style infrared receiver input. The rc-core- ++ based gpio_ir_recv driver maps received keys directly to a ++ /dev/input/event* device, all decoding is done by the kernel - LIRC is ++ not required! The key mapping and other decoding parameters can be ++ configured by "ir-keytable" tool. ++Load: dtoverlay=gpio-ir,= ++Params: gpio_pin Input pin number. Default is 18. ++ ++ gpio_pull Desired pull-up/down state (off, down, up) ++ Default is "up". ++ ++ invert "1" = invert the input (active-low signalling). ++ "0" = non-inverted input (active-high ++ signalling). Default is "1". ++ ++ rc-map-name Default rc keymap (can also be changed by ++ ir-keytable), defaults to "rc-rc6-mce" ++ ++ ++Name: gpio-ir-tx ++Info: Use GPIO pin as bit-banged infrared transmitter output. ++ This is an alternative to "pwm-ir-tx". gpio-ir-tx doesn't require ++ a PWM so it can be used together with onboard analog audio. ++Load: dtoverlay=gpio-ir-tx,= ++Params: gpio_pin Output GPIO (default 18) ++ ++ invert "1" = invert the output (make it active-low). ++ Default is "0" (active-high). ++ ++ ++Name: gpio-key ++Info: This is a generic overlay for activating GPIO keypresses using ++ the gpio-keys library and this dtoverlay. Multiple keys can be ++ set up using multiple calls to the overlay for configuring ++ additional buttons or joysticks. You can see available keycodes ++ at https://github.com/torvalds/linux/blob/v4.12/include/uapi/ ++ linux/input-event-codes.h#L64 ++Load: dtoverlay=gpio-key,= ++Params: gpio GPIO pin to trigger on (default 3) ++ active_low When this is 1 (active low), a falling ++ edge generates a key down event and a ++ rising edge generates a key up event. ++ When this is 0 (active high), this is ++ reversed. The default is 1 (active low) ++ gpio_pull Desired pull-up/down state (off, down, up) ++ Default is "up". Note that the default pin ++ (GPIO3) has an external pullup ++ label Set a label for the key ++ keycode Set the key code for the button ++ ++ ++Name: gpio-no-bank0-irq ++Info: Use this overlay to disable GPIO interrupts for GPIOs in bank 0 (0-27), ++ which can be useful for UIO drivers. ++ N.B. Using this overlay will trigger a kernel WARN during booting, but ++ this can safely be ignored - the system should work as expected. ++Load: dtoverlay=gpio-no-bank0-irq ++Params: ++ ++ ++Name: gpio-no-irq ++Info: Use this overlay to disable all GPIO interrupts, which can be useful ++ for user-space GPIO edge detection systems. ++Load: dtoverlay=gpio-no-irq ++Params: ++ ++ ++Name: gpio-poweroff ++Info: Drives a GPIO high or low on poweroff (including halt). Enabling this ++ overlay will prevent the ability to boot by driving GPIO3 low. ++Load: dtoverlay=gpio-poweroff,= ++Params: gpiopin GPIO for signalling (default 26) ++ ++ active_low Set if the power control device requires a ++ high->low transition to trigger a power-down. ++ Note that this will require the support of a ++ custom dt-blob.bin to prevent a power-down ++ during the boot process, and that a reboot ++ will also cause the pin to go low. ++ input Set if the gpio pin should be configured as ++ an input. ++ export Set to export the configured pin to sysfs ++ timeout_ms Specify (in ms) how long the kernel waits for ++ power-down before issuing a WARN (default 3000). ++ ++ ++Name: gpio-shutdown ++Info: Initiates a shutdown when GPIO pin changes. The given GPIO pin ++ is configured as an input key that generates KEY_POWER events. ++ ++ This event is handled by systemd-logind by initiating a ++ shutdown. Systemd versions older than 225 need an udev rule ++ enable listening to the input device: ++ ++ ACTION!="REMOVE", SUBSYSTEM=="input", KERNEL=="event*", \ ++ SUBSYSTEMS=="platform", DRIVERS=="gpio-keys", \ ++ ATTRS{keys}=="116", TAG+="power-switch" ++ ++ Alternatively this event can be handled also on systems without ++ systemd, just by traditional SysV init daemon. KEY_POWER event ++ (keycode 116) needs to be mapped to KeyboardSignal on console ++ and then kb::kbrequest inittab action which is triggered by ++ KeyboardSignal from console can be configured to issue system ++ shutdown. Steps for this configuration are: ++ ++ Add following lines to the /etc/console-setup/remap.inc file: ++ ++ # Key Power as special keypress ++ keycode 116 = KeyboardSignal ++ ++ Then add following lines to /etc/inittab file: ++ ++ # Action on special keypress (Key Power) ++ kb::kbrequest:/sbin/shutdown -t1 -a -h -P now ++ ++ And finally reload configuration by calling following commands: ++ ++ # dpkg-reconfigure console-setup ++ # service console-setup reload ++ # init q ++ ++ This overlay only handles shutdown. After shutdown, the system ++ can be powered up again by driving GPIO3 low. The default ++ configuration uses GPIO3 with a pullup, so if you connect a ++ button between GPIO3 and GND (pin 5 and 6 on the 40-pin header), ++ you get a shutdown and power-up button. Please note that ++ Raspberry Pi 1 Model B rev 1 uses GPIO1 instead of GPIO3. ++Load: dtoverlay=gpio-shutdown,= ++Params: gpio_pin GPIO pin to trigger on (default 3) ++ For Raspberry Pi 1 Model B rev 1 set this ++ explicitly to value 1, e.g.: ++ ++ dtoverlay=gpio-shutdown,gpio_pin=1 ++ ++ active_low When this is 1 (active low), a falling ++ edge generates a key down event and a ++ rising edge generates a key up event. ++ When this is 0 (active high), this is ++ reversed. The default is 1 (active low). ++ ++ gpio_pull Desired pull-up/down state (off, down, up) ++ Default is "up". ++ ++ Note that the default pin (GPIO3) has an ++ external pullup. Same applies for GPIO1 ++ on Raspberry Pi 1 Model B rev 1. ++ ++ debounce Specify the debounce interval in milliseconds ++ (default 100) ++ ++ ++Name: hd44780-lcd ++Info: Configures an HD44780 compatible LCD display. Uses 4 gpio pins for ++ data, 2 gpio pins for enable and register select and 1 optional pin ++ for enabling/disabling the backlight display. ++Load: dtoverlay=hd44780-lcd,= ++Params: pin_d4 GPIO pin for data pin D4 (default 6) ++ ++ pin_d5 GPIO pin for data pin D5 (default 13) ++ ++ pin_d6 GPIO pin for data pin D6 (default 19) ++ ++ pin_d7 GPIO pin for data pin D7 (default 26) ++ ++ pin_en GPIO pin for "Enable" (default 21) ++ ++ pin_rs GPIO pin for "Register Select" (default 20) ++ ++ pin_bl Optional pin for enabling/disabling the ++ display backlight. (default disabled) ++ ++ display_height Height of the display in characters ++ ++ display_width Width of the display in characters ++ ++ ++Name: hdmi-backlight-hwhack-gpio ++Info: Devicetree overlay for GPIO based backlight on/off capability. ++ Use this if you have one of those HDMI displays whose backlight cannot ++ be controlled via DPMS over HDMI and plan to do a little soldering to ++ use an RPi gpio pin for on/off switching. See: ++ https://www.waveshare.com/wiki/7inch_HDMI_LCD_(C)#Backlight_Control ++Load: dtoverlay=hdmi-backlight-hwhack-gpio,= ++Params: gpio_pin GPIO pin used (default 17) ++ active_low Set this to 1 if the display backlight is ++ switched on when the wire goes low. ++ Leave the default (value 0) if the backlight ++ expects a high to switch it on. ++ ++ ++Name: hifiberry-amp ++Info: Configures the HifiBerry Amp and Amp+ audio cards ++Load: dtoverlay=hifiberry-amp ++Params: ++ ++ ++Name: hifiberry-dac ++Info: Configures the HifiBerry DAC audio card ++Load: dtoverlay=hifiberry-dac ++Params: ++ ++ ++Name: hifiberry-dacplus ++Info: Configures the HifiBerry DAC+ audio card ++Load: dtoverlay=hifiberry-dacplus,= ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ "dtoverlay=hifiberry-dacplus,24db_digital_gain" ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24dB_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ slave Force DAC+ Pro into slave mode, using Pi as ++ master for bit clock and frame clock. ++ leds_off If set to 'true' the onboard indicator LEDs ++ are switched off at all times. ++ ++ ++Name: hifiberry-dacplusadc ++Info: Configures the HifiBerry DAC+ADC audio card ++Load: dtoverlay=hifiberry-dacplusadc,= ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ "dtoverlay=hifiberry-dacplus,24db_digital_gain" ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24dB_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ slave Force DAC+ Pro into slave mode, using Pi as ++ master for bit clock and frame clock. ++ leds_off If set to 'true' the onboard indicator LEDs ++ are switched off at all times. ++ ++ ++Name: hifiberry-dacplusadcpro ++Info: Configures the HifiBerry DAC+ADC PRO audio card ++Load: dtoverlay=hifiberry-dacplusadcpro,= ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ "dtoverlay=hifiberry-dacplusadcpro,24db_digital_gain" ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24dB_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ slave Force DAC+ADC Pro into slave mode, using Pi as ++ master for bit clock and frame clock. ++ leds_off If set to 'true' the onboard indicator LEDs ++ are switched off at all times. ++ ++ ++Name: hifiberry-dacplusdsp ++Info: Configures the HifiBerry DAC+DSP audio card ++Load: dtoverlay=hifiberry-dacplusdsp ++Params: ++ ++ ++Name: hifiberry-dacplushd ++Info: Configures the HifiBerry DAC+ HD audio card ++Load: dtoverlay=hifiberry-dacplushd ++Params: ++ ++ ++Name: hifiberry-digi ++Info: Configures the HifiBerry Digi and Digi+ audio card ++Load: dtoverlay=hifiberry-digi ++Params: ++ ++ ++Name: hifiberry-digi-pro ++Info: Configures the HifiBerry Digi+ Pro audio card ++Load: dtoverlay=hifiberry-digi-pro ++Params: ++ ++ ++Name: highperi ++Info: Enables "High Peripheral" mode ++Load: dtoverlay=highperi ++Params: ++ ++ ++Name: hy28a ++Info: HY28A - 2.8" TFT LCD Display Module by HAOYU Electronics ++ Default values match Texy's display shield ++Load: dtoverlay=hy28a,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ xohms Touchpanel sensitivity (X-plate resistance) ++ ++ resetgpio GPIO used to reset controller ++ ++ ledgpio GPIO used to control backlight ++ ++ ++Name: hy28b ++Info: HY28B - 2.8" TFT LCD Display Module by HAOYU Electronics ++ Default values match Texy's display shield ++Load: dtoverlay=hy28b,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ xohms Touchpanel sensitivity (X-plate resistance) ++ ++ resetgpio GPIO used to reset controller ++ ++ ledgpio GPIO used to control backlight ++ ++ ++Name: hy28b-2017 ++Info: HY28B 2017 version - 2.8" TFT LCD Display Module by HAOYU Electronics ++ Default values match Texy's display shield ++Load: dtoverlay=hy28b-2017,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ xohms Touchpanel sensitivity (X-plate resistance) ++ ++ resetgpio GPIO used to reset controller ++ ++ ledgpio GPIO used to control backlight ++ ++ ++Name: i-sabre-q2m ++Info: Configures the Audiophonics I-SABRE Q2M DAC ++Load: dtoverlay=i-sabre-q2m ++Params: ++ ++ ++Name: i2c-bcm2708 ++Info: Fall back to the i2c_bcm2708 driver for the i2c_arm bus. ++Load: dtoverlay=i2c-bcm2708 ++Params: ++ ++ ++Name: i2c-gpio ++Info: Adds support for software i2c controller on gpio pins ++Load: dtoverlay=i2c-gpio,= ++Params: i2c_gpio_sda GPIO used for I2C data (default "23") ++ ++ i2c_gpio_scl GPIO used for I2C clock (default "24") ++ ++ i2c_gpio_delay_us Clock delay in microseconds ++ (default "2" = ~100kHz) ++ ++ bus Set to a unique, non-zero value if wanting ++ multiple i2c-gpio busses. If set, will be used ++ as the preferred bus number (/dev/i2c-). If ++ not set, the default value is 0, but the bus ++ number will be dynamically assigned - probably ++ 3. ++ ++ ++Name: i2c-mux ++Info: Adds support for a number of I2C bus multiplexers on i2c_arm ++Load: dtoverlay=i2c-mux,= ++Params: pca9542 Select the NXP PCA9542 device ++ ++ pca9545 Select the NXP PCA9545 device ++ ++ pca9548 Select the NXP PCA9548 device ++ ++ addr Change I2C address of the device (default 0x70) ++ ++ ++[ The i2c-mux-pca9548a overlay has been deleted. See i2c-mux. ] ++ ++ ++Name: i2c-pwm-pca9685a ++Info: Adds support for an NXP PCA9685A I2C PWM controller on i2c_arm ++Load: dtoverlay=i2c-pwm-pca9685a,= ++Params: addr I2C address of PCA9685A (default 0x40) ++ ++ ++Name: i2c-rtc ++Info: Adds support for a number of I2C Real Time Clock devices ++Load: dtoverlay=i2c-rtc,= ++Params: abx80x Select one of the ABx80x family: ++ AB0801, AB0803, AB0804, AB0805, ++ AB1801, AB1803, AB1804, AB1805 ++ ++ ds1307 Select the DS1307 device ++ ++ ds1339 Select the DS1339 device ++ ++ ds3231 Select the DS3231 device ++ ++ m41t62 Select the M41T62 device ++ ++ mcp7940x Select the MCP7940x device ++ ++ mcp7941x Select the MCP7941x device ++ ++ pcf2127 Select the PCF2127 device ++ ++ pcf2129 Select the PCF2129 device ++ ++ pcf8523 Select the PCF8523 device ++ ++ pcf85363 Select the PCF85363 device ++ ++ pcf8563 Select the PCF8563 device ++ ++ rv1805 Select the Micro Crystal RV1805 device ++ ++ rv3028 Select the Micro Crystal RV3028 device ++ ++ sd3078 Select the ZXW Shenzhen whwave SD3078 device ++ ++ addr Sets the address for the RTC. Note that the ++ device must be configured to use the specified ++ address. ++ ++ trickle-diode-type Diode type for trickle charge - "standard" or ++ "schottky" (ABx80x and RV1805 only) ++ ++ trickle-resistor-ohms Resistor value for trickle charge (DS1339, ++ ABx80x, RV1805, RV3028) ++ ++ wakeup-source Specify that the RTC can be used as a wakeup ++ source ++ ++ backup-switchover-mode Backup power supply switch mode. Must be 0 for ++ off or 1 for Vdd < VBackup (RV3028 only) ++ ++ ++Name: i2c-rtc-gpio ++Info: Adds support for a number of I2C Real Time Clock devices ++ using the software i2c controller ++Load: dtoverlay=i2c-rtc-gpio,= ++Params: abx80x Select one of the ABx80x family: ++ AB0801, AB0803, AB0804, AB0805, ++ AB1801, AB1803, AB1804, AB1805 ++ ++ ds1307 Select the DS1307 device ++ ++ ds1339 Select the DS1339 device ++ ++ ds3231 Select the DS3231 device ++ ++ m41t62 Select the M41T62 device ++ ++ mcp7940x Select the MCP7940x device ++ ++ mcp7941x Select the MCP7941x device ++ ++ pcf2127 Select the PCF2127 device ++ ++ pcf2129 Select the PCF2129 device ++ ++ pcf8523 Select the PCF8523 device ++ ++ pcf8563 Select the PCF8563 device ++ ++ rv1805 Select the Micro Crystal RV1805 device ++ ++ rv3028 Select the Micro Crystal RV3028 device ++ ++ addr Sets the address for the RTC. Note that the ++ device must be configured to use the specified ++ address. ++ ++ trickle-diode-type Diode type for trickle charge - "standard" or ++ "schottky" (ABx80x and RV1805 only) ++ ++ trickle-resistor-ohms Resistor value for trickle charge (DS1339, ++ ABx80x, RV1805, RV3028) ++ ++ wakeup-source Specify that the RTC can be used as a wakeup ++ source ++ ++ backup-switchover-mode Backup power supply switch mode. Must be 0 for ++ off or 1 for Vdd < VBackup (RV3028 only) ++ ++ i2c_gpio_sda GPIO used for I2C data (default "23") ++ ++ i2c_gpio_scl GPIO used for I2C clock (default "24") ++ ++ i2c_gpio_delay_us Clock delay in microseconds ++ (default "2" = ~100kHz) ++ ++ ++Name: i2c-sensor ++Info: Adds support for a number of I2C barometric pressure and temperature ++ sensors on i2c_arm ++Load: dtoverlay=i2c-sensor,= ++Params: addr Set the address for the BME280, BME680, BMP280, ++ DS1621, HDC100X, LM75, SHT3x or TMP102 ++ ++ bme280 Select the Bosch Sensortronic BME280 ++ Valid addresses 0x76-0x77, default 0x76 ++ ++ bme680 Select the Bosch Sensortronic BME680 ++ Valid addresses 0x76-0x77, default 0x76 ++ ++ bmp085 Select the Bosch Sensortronic BMP085 ++ ++ bmp180 Select the Bosch Sensortronic BMP180 ++ ++ bmp280 Select the Bosch Sensortronic BMP280 ++ Valid addresses 0x76-0x77, default 0x76 ++ ++ ds1621 Select the Dallas Semiconductors DS1621 temp ++ sensor. Valid addresses 0x48-0x4f, default 0x48 ++ ++ hdc100x Select the Texas Instruments HDC100x temp sensor ++ Valid addresses 0x40-0x43, default 0x40 ++ ++ htu21 Select the HTU21 temperature and humidity sensor ++ ++ lm75 Select the Maxim LM75 temperature sensor ++ Valid addresses 0x48-0x4f, default 0x4f ++ ++ lm75addr Deprecated - use addr parameter instead ++ ++ max17040 Select the Maxim Integrated MAX17040 battery ++ monitor ++ ++ sht3x Select the Sensiron SHT3x temperature and ++ humidity sensor. Valid addresses 0x44-0x45, ++ default 0x44 ++ ++ si7020 Select the Silicon Labs Si7013/20/21 humidity/ ++ temperature sensor ++ ++ sps30 Select the Sensirion SPS30 particulate matter ++ sensor. Fixed address 0x69. ++ ++ tmp102 Select the Texas Instruments TMP102 temp sensor ++ Valid addresses 0x48-0x4b, default 0x48 ++ ++ tsl4531 Select the AMS TSL4531 digital ambient light ++ sensor ++ ++ veml6070 Select the Vishay VEML6070 ultraviolet light ++ sensor ++ ++ ++Name: i2c0 ++Info: Change i2c0 pin usage. Not all pin combinations are usable on all ++ platforms - platforms other then Compute Modules can only use this ++ to disable transaction combining. ++ Do NOT use in conjunction with dtparam=i2c_vc=on. From the 5.4 kernel ++ onwards the base DT includes the use of i2c_mux_pinctrl to expose two ++ muxings of BSC0 - GPIOs 0&1, and whichever combination is used for the ++ camera and display connectors. This overlay disables that mux and ++ configures /dev/i2c0 to point at whichever set of pins is requested. ++ dtparam=i2c_vc=on will try and enable the mux, so combining the two ++ will cause conflicts. ++Load: dtoverlay=i2c0,= ++Params: pins_0_1 Use pins 0 and 1 (default) ++ pins_28_29 Use pins 28 and 29 ++ pins_44_45 Use pins 44 and 45 ++ pins_46_47 Use pins 46 and 47 ++ combine Allow transactions to be combined (default ++ "yes") ++ ++ ++Name: i2c0-bcm2708 ++Info: Deprecated, legacy version of i2c0. ++Load: ++ ++ ++Name: i2c1 ++Info: Change i2c1 pin usage. Not all pin combinations are usable on all ++ platforms - platforms other then Compute Modules can only use this ++ to disable transaction combining. ++Load: dtoverlay=i2c1,= ++Params: pins_2_3 Use pins 2 and 3 (default) ++ pins_44_45 Use pins 44 and 45 ++ combine Allow transactions to be combined (default ++ "yes") ++ ++ ++Name: i2c1-bcm2708 ++Info: Deprecated, legacy version of i2c1. ++Load: ++ ++ ++Name: i2c3 ++Info: Enable the i2c3 bus. BCM2711 only. ++Load: dtoverlay=i2c3, ++Params: pins_2_3 Use GPIOs 2 and 3 ++ pins_4_5 Use GPIOs 4 and 5 (default) ++ baudrate Set the baudrate for the interface (default ++ "100000") ++ ++ ++Name: i2c4 ++Info: Enable the i2c4 bus. BCM2711 only. ++Load: dtoverlay=i2c4, ++Params: pins_6_7 Use GPIOs 6 and 7 ++ pins_8_9 Use GPIOs 8 and 9 (default) ++ baudrate Set the baudrate for the interface (default ++ "100000") ++ ++ ++Name: i2c5 ++Info: Enable the i2c5 bus. BCM2711 only. ++Load: dtoverlay=i2c5, ++Params: pins_10_11 Use GPIOs 10 and 11 ++ pins_12_13 Use GPIOs 12 and 13 (default) ++ baudrate Set the baudrate for the interface (default ++ "100000") ++ ++ ++Name: i2c6 ++Info: Enable the i2c6 bus. BCM2711 only. ++Load: dtoverlay=i2c6, ++Params: pins_0_1 Use GPIOs 0 and 1 ++ pins_22_23 Use GPIOs 22 and 23 (default) ++ baudrate Set the baudrate for the interface (default ++ "100000") ++ ++ ++Name: i2s-gpio28-31 ++Info: move I2S function block to GPIO 28 to 31 ++Load: dtoverlay=i2s-gpio28-31 ++Params: ++ ++ ++Name: ilitek251x ++Info: Enables I2C connected Ilitek 251x multiple touch controller using ++ GPIO 4 (pin 7 on GPIO header) for interrupt. ++Load: dtoverlay=ilitek251x,= ++Params: interrupt GPIO used for interrupt (default 4) ++ sizex Touchscreen size x, horizontal resolution of ++ touchscreen (in pixels) ++ sizey Touchscreen size y, vertical resolution of ++ touchscreen (in pixels) ++ ++ ++Name: imx219 ++Info: Sony IMX219 camera module. ++ Uses Unicam 1, which is the standard camera connector on most Pi ++ variants. ++Load: dtoverlay=imx219,= ++Params: rotation Mounting rotation of the camera sensor (0 or ++ 180, default 180) ++ ++ ++Name: imx290 ++Info: Sony IMX290 camera module. ++ Uses Unicam 1, which is the standard camera connector on most Pi ++ variants. NB This currently uses 4 CSI2 data lanes and therefore will ++ only work on a CM. ++Load: dtoverlay=imx290, ++Params: 4lane Enable 4 CSI2 lanes. This requires a Compute ++ Module (1, 3, or 4). ++ clock-frequency Sets the clock frequency to match that used on ++ the board. ++ Modules from Vision Components use 37.125MHz ++ (the default), whilst those from Innomaker use ++ 74.25MHz. ++ mono Denote that the module is a mono sensor. ++ ++ ++Name: imx477 ++Info: Sony IMX477 camera module. ++ Uses Unicam 1, which is the standard camera connector on most Pi ++ variants. ++Load: dtoverlay=imx477,= ++Params: rotation Mounting rotation of the camera sensor (0 or ++ 180, default 180) ++ ++ ++Name: iqaudio-codec ++Info: Configures the IQaudio Codec audio card ++Load: dtoverlay=iqaudio-codec ++Params: ++ ++ ++Name: iqaudio-dac ++Info: Configures the IQaudio DAC audio card ++Load: dtoverlay=iqaudio-dac, ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ "dtoverlay=iqaudio-dac,24db_digital_gain" ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24db_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ ++ ++Name: iqaudio-dacplus ++Info: Configures the IQaudio DAC+ audio card ++Load: dtoverlay=iqaudio-dacplus,= ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ "dtoverlay=iqaudio-dacplus,24db_digital_gain" ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24db_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ auto_mute_amp If specified, unmute/mute the IQaudIO amp when ++ starting/stopping audio playback. ++ unmute_amp If specified, unmute the IQaudIO amp once when ++ the DAC driver module loads. ++ ++ ++Name: iqaudio-digi-wm8804-audio ++Info: Configures the IQAudIO Digi WM8804 audio card ++Load: dtoverlay=iqaudio-digi-wm8804-audio,= ++Params: card_name Override the default, "IQAudIODigi", card name. ++ dai_name Override the default, "IQAudIO Digi", dai name. ++ dai_stream_name Override the default, "IQAudIO Digi HiFi", ++ dai stream name. ++ ++ ++Name: irs1125 ++Info: Infineon irs1125 TOF camera module. ++ Uses Unicam 1, which is the standard camera connector on most Pi ++ variants. ++Load: dtoverlay=irs1125 ++Params: ++ ++ ++Name: jedec-spi-nor ++Info: Adds support for JEDEC-compliant SPI NOR flash devices. (Note: The ++ "jedec,spi-nor" kernel driver was formerly known as "m25p80".) ++Load: dtoverlay=jedec-spi-nor,= ++Params: flash-spi- Enables flash device on SPI, CS#. ++ flash-fastr-spi- Enables flash device with fast read capability ++ on SPI, CS#. ++ ++ ++Name: justboom-both ++Info: Simultaneous usage of an justboom-dac and justboom-digi based ++ card ++Load: dtoverlay=justboom-both,= ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ "dtoverlay=justboom-dac,24db_digital_gain" ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24dB_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ ++ ++Name: justboom-dac ++Info: Configures the JustBoom DAC HAT, Amp HAT, DAC Zero and Amp Zero audio ++ cards ++Load: dtoverlay=justboom-dac,= ++Params: 24db_digital_gain Allow gain to be applied via the PCM512x codec ++ Digital volume control. Enable with ++ "dtoverlay=justboom-dac,24db_digital_gain" ++ (The default behaviour is that the Digital ++ volume control is limited to a maximum of ++ 0dB. ie. it can attenuate but not provide ++ gain. For most users, this will be desired ++ as it will prevent clipping. By appending ++ the 24dB_digital_gain parameter, the Digital ++ volume control will allow up to 24dB of ++ gain. If this parameter is enabled, it is the ++ responsibility of the user to ensure that ++ the Digital volume control is set to a value ++ that does not result in clipping/distortion!) ++ ++ ++Name: justboom-digi ++Info: Configures the JustBoom Digi HAT and Digi Zero audio cards ++Load: dtoverlay=justboom-digi ++Params: ++ ++ ++Name: lirc-rpi ++Info: This overlay has been deprecated and removed - see gpio-ir ++Load: ++ ++ ++Name: ltc294x ++Info: Adds support for the ltc294x family of battery gauges ++Load: dtoverlay=ltc294x,= ++Params: ltc2941 Select the ltc2941 device ++ ++ ltc2942 Select the ltc2942 device ++ ++ ltc2943 Select the ltc2943 device ++ ++ ltc2944 Select the ltc2944 device ++ ++ resistor-sense The sense resistor value in milli-ohms. ++ Can be a 32-bit negative value when the battery ++ has been connected to the wrong end of the ++ resistor. ++ ++ prescaler-exponent Range and accuracy of the gauge. The value is ++ programmed into the chip only if it differs ++ from the current setting. ++ For LTC2941 only: ++ - Default value is 128 ++ - the exponent is in the range 0-7 (default 7) ++ See the datasheet for more information. ++ ++ ++Name: max98357a ++Info: Configures the Maxim MAX98357A I2S DAC ++Load: dtoverlay=max98357a,= ++Params: no-sdmode Driver does not manage the state of the DAC's ++ SD_MODE pin (i.e. chip is always on). ++ sdmode-pin integer, GPIO pin connected to the SD_MODE input ++ of the DAC (default GPIO4 if parameter omitted). ++ ++ ++Name: maxtherm ++Info: Configure a MAX6675 or MAX31855 thermocouple as an IIO device. ++ ++ For devices on spi1 or spi2, the interfaces should be enabled ++ with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays. ++ The overlay expects to disable the relevant spidev node, so also using ++ e.g. cs0_spidev=off is unnecessary. ++ ++ Note: with the 5.7 kernel (and later) there will also be ++ overlays for MAX31855E, MAX31855J, MAX31855K, ++ MAX31885N, MAX31855R, MAX31855S and MAX31855T. ++ ++ Example: ++ MAX31855 on /dev/spidev0.0 ++ dtoverlay=maxtherm,spi0-0,max31855 ++ ++Load: dtoverlay=maxtherm,= ++Params: spi- Configure device at spi, cs ++ (boolean, required) ++ max6675 Enable support for the MAX6675 (default) ++ max31855 Enable support for the MAX31855 ++ max31855e Enable support for the MAX31855E ++ max31855j Enable support for the MAX31855J ++ max31855k Enable support for the MAX31855K ++ max31855n Enable support for the MAX31855N ++ max31855r Enable support for the MAX31855R ++ max31855s Enable support for the MAX31855S ++ max31855t Enable support for the MAX31855T ++ ++ ++Name: mbed-dac ++Info: Configures the mbed AudioCODEC (TLV320AIC23B) ++Load: dtoverlay=mbed-dac ++Params: ++ ++ ++Name: mcp23017 ++Info: Configures the MCP23017 I2C GPIO expander ++Load: dtoverlay=mcp23017,= ++Params: gpiopin Gpio pin connected to the INTA output of the ++ MCP23017 (default: 4) ++ ++ addr I2C address of the MCP23017 (default: 0x20) ++ ++ mcp23008 Configure an MCP23008 instead. ++ noints Disable the interrupt GPIO line. ++ ++ ++Name: mcp23s17 ++Info: Configures the MCP23S08/17 SPI GPIO expanders. ++ If devices are present on SPI1 or SPI2, those interfaces must be enabled ++ with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays. ++ If interrupts are enabled for a device on a given CS# on a SPI bus, that ++ device must be the only one present on that SPI bus/CS#. ++Load: dtoverlay=mcp23s17,= ++Params: s08-spi--present 4-bit integer, bitmap indicating MCP23S08 ++ devices present on SPI, CS# ++ ++ s17-spi--present 8-bit integer, bitmap indicating MCP23S17 ++ devices present on SPI, CS# ++ ++ s08-spi--int-gpio integer, enables interrupts on a single ++ MCP23S08 device on SPI, CS#, specifies ++ the GPIO pin to which INT output of MCP23S08 ++ is connected. ++ ++ s17-spi--int-gpio integer, enables mirrored interrupts on a ++ single MCP23S17 device on SPI, CS#, ++ specifies the GPIO pin to which either INTA ++ or INTB output of MCP23S17 is connected. ++ ++ ++Name: mcp2515-can0 ++Info: Configures the MCP2515 CAN controller on spi0.0 ++Load: dtoverlay=mcp2515-can0,= ++Params: oscillator Clock frequency for the CAN controller (Hz) ++ ++ spimaxfrequency Maximum SPI frequence (Hz) ++ ++ interrupt GPIO for interrupt signal ++ ++ ++Name: mcp2515-can1 ++Info: Configures the MCP2515 CAN controller on spi0.1 ++Load: dtoverlay=mcp2515-can1,= ++Params: oscillator Clock frequency for the CAN controller (Hz) ++ ++ spimaxfrequency Maximum SPI frequence (Hz) ++ ++ interrupt GPIO for interrupt signal ++ ++ ++Name: mcp3008 ++Info: Configures MCP3008 A/D converters ++ For devices on spi1 or spi2, the interfaces should be enabled ++ with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays. ++Load: dtoverlay=mcp3008,[=] ++Params: spi--present boolean, configure device at spi, cs ++ spi--speed integer, set the spi bus speed for this device ++ ++ ++Name: mcp3202 ++Info: Configures MCP3202 A/D converters ++ For devices on spi1 or spi2, the interfaces should be enabled ++ with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays. ++Load: dtoverlay=mcp3202,[=] ++Params: spi--present boolean, configure device at spi, cs ++ spi--speed integer, set the spi bus speed for this device ++ ++ ++Name: mcp342x ++Info: Overlay for activation of Microchip MCP3421-3428 ADCs over I2C ++Load: dtoverlay=mcp342x,= ++Params: addr I2C bus address of device, for devices with ++ addresses that are configurable, e.g. by ++ hardware links (default=0x68) ++ mcp3421 The device is an MCP3421 ++ mcp3422 The device is an MCP3422 ++ mcp3423 The device is an MCP3423 ++ mcp3424 The device is an MCP3424 ++ mcp3425 The device is an MCP3425 ++ mcp3426 The device is an MCP3426 ++ mcp3427 The device is an MCP3427 ++ mcp3428 The device is an MCP3428 ++ ++ ++Name: media-center ++Info: Media Center HAT - 2.83" Touch Display + extras by Pi Supply ++Load: dtoverlay=media-center,= ++Params: speed Display SPI bus speed ++ rotate Display rotation {0,90,180,270} ++ fps Delay between frame updates ++ xohms Touchpanel sensitivity (X-plate resistance) ++ swapxy Swap x and y axis ++ backlight Change backlight GPIO pin {e.g. 12, 18} ++ gpio_out_pin GPIO for output (default "17") ++ gpio_in_pin GPIO for input (default "18") ++ gpio_in_pull Pull up/down/off on the input pin ++ (default "down") ++ sense Override the IR receive auto-detection logic: ++ "0" = force active-high ++ "1" = force active-low ++ "-1" = use auto-detection ++ (default "-1") ++ softcarrier Turn the software carrier "on" or "off" ++ (default "on") ++ invert "on" = invert the output pin (default "off") ++ debug "on" = enable additional debug messages ++ (default "off") ++ ++ ++Name: merus-amp ++Info: Configures the merus-amp audio card ++Load: dtoverlay=merus-amp ++Params: ++ ++ ++Name: midi-uart0 ++Info: Configures UART0 (ttyAMA0) so that a requested 38.4kbaud actually gets ++ 31.25kbaud, the frequency required for MIDI ++Load: dtoverlay=midi-uart0 ++Params: ++ ++ ++Name: midi-uart1 ++Info: Configures UART1 (ttyS0) so that a requested 38.4kbaud actually gets ++ 31.25kbaud, the frequency required for MIDI ++Load: dtoverlay=midi-uart1 ++Params: ++ ++ ++Name: miniuart-bt ++Info: Switch the onboard Bluetooth function on Pi 3B, 3B+, 3A+, 4B and Zero W ++ to use the mini-UART (ttyS0) and restore UART0/ttyAMA0 over GPIOs 14 & ++ 15. Note that this may reduce the maximum usable baudrate. ++ N.B. It is also necessary to edit /lib/systemd/system/hciuart.service ++ and replace ttyAMA0 with ttyS0, unless using Raspbian or another ++ distribution with udev rules that create /dev/serial0 and /dev/serial1, ++ in which case use /dev/serial1 instead because it will always be ++ correct. Furthermore, you must also set core_freq and core_freq_min to ++ the same value in config.txt or the miniuart will not work. ++Load: dtoverlay=miniuart-bt,= ++Params: krnbt Set to "on" to enable autoprobing of Bluetooth ++ driver without need of hciattach/btattach ++ ++ ++Name: mmc ++Info: Selects the bcm2835-mmc SD/MMC driver, optionally with overclock ++Load: dtoverlay=mmc,= ++Params: overclock_50 Clock (in MHz) to use when the MMC framework ++ requests 50MHz ++ ++ ++Name: mpu6050 ++Info: Overlay for i2c connected mpu6050 imu ++Load: dtoverlay=mpu6050,= ++Params: interrupt GPIO pin for interrupt (default 4) ++ ++ ++Name: mz61581 ++Info: MZ61581 display by Tontec ++Load: dtoverlay=mz61581,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ txbuflen Transmit buffer length (default 32768) ++ ++ debug Debug output level {0-7} ++ ++ xohms Touchpanel sensitivity (X-plate resistance) ++ ++ ++Name: ov5647 ++Info: Omnivision OV5647 camera module. ++ Uses Unicam 1, which is the standard camera connector on most Pi ++ variants. ++Load: dtoverlay=ov5647,= ++Params: rotation Mounting rotation of the camera sensor (0 or ++ 180, default 0) ++ ++ ++Name: ov7251 ++Info: Omnivision OV7251 camera module. ++ Uses Unicam 1, which is the standard camera connector on most Pi ++ variants. ++Load: dtoverlay=ov7251 ++Params: ++ ++ ++Name: ov9281 ++Info: Omnivision OV9281 camera module. ++ Uses Unicam 1, which is the standard camera connector on most Pi ++ variants. ++Load: dtoverlay=ov9281 ++Params: ++ ++ ++Name: papirus ++Info: PaPiRus ePaper Screen by Pi Supply (both HAT and pHAT) ++Load: dtoverlay=papirus,= ++Params: panel Display panel (required): ++ 1.44": e1144cs021 ++ 2.0": e2200cs021 ++ 2.7": e2271cs021 ++ ++ speed Display SPI bus speed ++ ++ ++Name: pca953x ++Info: TI PCA953x family of I2C GPIO expanders. Default is for NXP PCA9534. ++Load: dtoverlay=pca953x,= ++Params: addr I2C address of expander. Default 0x20. ++ pca6416 Select the NXP PCA6416 (16 bit) ++ pca9505 Select the NXP PCA9505 (40 bit) ++ pca9535 Select the NXP PCA9535 (16 bit) ++ pca9536 Select the NXP PCA9536 or TI PCA9536 (4 bit) ++ pca9537 Select the NXP PCA9537 (4 bit) ++ pca9538 Select the NXP PCA9538 (8 bit) ++ pca9539 Select the NXP PCA9539 (16 bit) ++ pca9554 Select the NXP PCA9554 (8 bit) ++ pca9555 Select the NXP PCA9555 (16 bit) ++ pca9556 Select the NXP PCA9556 (8 bit) ++ pca9557 Select the NXP PCA9557 (8 bit) ++ pca9574 Select the NXP PCA9574 (8 bit) ++ pca9575 Select the NXP PCA9575 (16 bit) ++ pca9698 Select the NXP PCA9698 (40 bit) ++ pca16416 Select the NXP PCA16416 (16 bit) ++ pca16524 Select the NXP PCA16524 (24 bit) ++ pca19555a Select the NXP PCA19555A (16 bit) ++ max7310 Select the Maxim MAX7310 (8 bit) ++ max7312 Select the Maxim MAX7312 (16 bit) ++ max7313 Select the Maxim MAX7313 (16 bit) ++ max7315 Select the Maxim MAX7315 (8 bit) ++ pca6107 Select the TI PCA6107 (8 bit) ++ tca6408 Select the TI TCA6408 (8 bit) ++ tca6416 Select the TI TCA6416 (16 bit) ++ tca6424 Select the TI TCA6424 (24 bit) ++ tca9539 Select the TI TCA9539 (16 bit) ++ tca9554 Select the TI TCA9554 (8 bit) ++ cat9554 Select the Onnn CAT9554 (8 bit) ++ pca9654 Select the Onnn PCA9654 (8 bit) ++ xra1202 Select the Exar XRA1202 (8 bit) ++ ++ ++[ The pcf2127-rtc overlay has been deleted. See i2c-rtc. ] ++ ++ ++[ The pcf8523-rtc overlay has been deleted. See i2c-rtc. ] ++ ++ ++[ The pcf8563-rtc overlay has been deleted. See i2c-rtc. ] ++ ++ ++Name: pi3-act-led ++Info: This overlay has been renamed act-led, keeping pi3-act-led as an alias ++ for backwards compatibility. ++Load: ++ ++ ++Name: pi3-disable-bt ++Info: This overlay has been renamed disable-bt, keeping pi3-disable-bt as an ++ alias for backwards compatibility. ++Load: ++ ++ ++Name: pi3-disable-wifi ++Info: This overlay has been renamed disable-wifi, keeping pi3-disable-wifi as ++ an alias for backwards compatibility. ++Load: ++ ++ ++Name: pi3-miniuart-bt ++Info: This overlay has been renamed miniuart-bt, keeping pi3-miniuart-bt as ++ an alias for backwards compatibility. ++Load: ++ ++ ++Name: pibell ++Info: Configures the pibell audio card. ++Load: dtoverlay=pibell,= ++Params: alsaname Set the name as it appears in ALSA (default ++ "PiBell") ++ ++ ++Name: pifacedigital ++Info: Configures the PiFace Digital mcp23s17 GPIO port expander. ++Load: dtoverlay=pifacedigital,= ++Params: spi-present-mask 8-bit integer, bitmap indicating MCP23S17 SPI0 ++ CS0 address. PiFace Digital supports addresses ++ 0-3, which can be configured with JP1 and JP2. ++ ++ ++Name: piglow ++Info: Configures the PiGlow by pimoroni.com ++Load: dtoverlay=piglow ++Params: ++ ++ ++Name: piscreen ++Info: PiScreen display by OzzMaker.com ++Load: dtoverlay=piscreen,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ xohms Touchpanel sensitivity (X-plate resistance) ++ ++ ++Name: piscreen2r ++Info: PiScreen 2 with resistive TP display by OzzMaker.com ++Load: dtoverlay=piscreen2r,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ xohms Touchpanel sensitivity (X-plate resistance) ++ ++ ++Name: pisound ++Info: Configures the Blokas Labs pisound card ++Load: dtoverlay=pisound ++Params: ++ ++ ++Name: pitft22 ++Info: Adafruit PiTFT 2.2" screen ++Load: dtoverlay=pitft22,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ ++Name: pitft28-capacitive ++Info: Adafruit PiTFT 2.8" capacitive touch screen ++Load: dtoverlay=pitft28-capacitive,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ touch-sizex Touchscreen size x (default 240) ++ ++ touch-sizey Touchscreen size y (default 320) ++ ++ touch-invx Touchscreen inverted x axis ++ ++ touch-invy Touchscreen inverted y axis ++ ++ touch-swapxy Touchscreen swapped x y axis ++ ++ ++Name: pitft28-resistive ++Info: Adafruit PiTFT 2.8" resistive touch screen ++Load: dtoverlay=pitft28-resistive,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ ++Name: pitft35-resistive ++Info: Adafruit PiTFT 3.5" resistive touch screen ++Load: dtoverlay=pitft35-resistive,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ ++Name: pps-gpio ++Info: Configures the pps-gpio (pulse-per-second time signal via GPIO). ++Load: dtoverlay=pps-gpio,= ++Params: gpiopin Input GPIO (default "18") ++ assert_falling_edge When present, assert is indicated by a falling ++ edge, rather than by a rising edge (default ++ off) ++ capture_clear Generate clear events on the trailing edge ++ (default off) ++ ++ ++Name: pwm ++Info: Configures a single PWM channel ++ Legal pin,function combinations for each channel: ++ PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0) 52,5(Alt1) ++ PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1) ++ N.B.: ++ 1) Pin 18 is the only one available on all platforms, and ++ it is the one used by the I2S audio interface. ++ Pins 12 and 13 might be better choices on an A+, B+ or Pi2. ++ 2) The onboard analogue audio output uses both PWM channels. ++ 3) So be careful mixing audio and PWM. ++ 4) Currently the clock must have been enabled and configured ++ by other means. ++Load: dtoverlay=pwm,= ++Params: pin Output pin (default 18) - see table ++ func Pin function (default 2 = Alt5) - see above ++ clock PWM clock frequency (informational) ++ ++ ++Name: pwm-2chan ++Info: Configures both PWM channels ++ Legal pin,function combinations for each channel: ++ PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0) 52,5(Alt1) ++ PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1) ++ N.B.: ++ 1) Pin 18 is the only one available on all platforms, and ++ it is the one used by the I2S audio interface. ++ Pins 12 and 13 might be better choices on an A+, B+ or Pi2. ++ 2) The onboard analogue audio output uses both PWM channels. ++ 3) So be careful mixing audio and PWM. ++ 4) Currently the clock must have been enabled and configured ++ by other means. ++Load: dtoverlay=pwm-2chan,= ++Params: pin Output pin (default 18) - see table ++ pin2 Output pin for other channel (default 19) ++ func Pin function (default 2 = Alt5) - see above ++ func2 Function for pin2 (default 2 = Alt5) ++ clock PWM clock frequency (informational) ++ ++ ++Name: pwm-ir-tx ++Info: Use GPIO pin as pwm-assisted infrared transmitter output. ++ This is an alternative to "gpio-ir-tx". pwm-ir-tx makes use ++ of PWM0 to reduce the CPU load during transmission compared to ++ gpio-ir-tx which uses bit-banging. ++ Legal pin,function combinations are: ++ 12,4(Alt0) 18,2(Alt5) 40,4(Alt0) 52,5(Alt1) ++Load: dtoverlay=pwm-ir-tx,= ++Params: gpio_pin Output GPIO (default 18) ++ ++ func Pin function (default 2 = Alt5) ++ ++ ++Name: qca7000 ++Info: I2SE's Evaluation Board for PLC Stamp micro ++Load: dtoverlay=qca7000,= ++Params: int_pin GPIO pin for interrupt signal (default 23) ++ ++ speed SPI bus speed (default 12 MHz) ++ ++ ++Name: rotary-encoder ++Info: Overlay for GPIO connected rotary encoder. ++Load: dtoverlay=rotary-encoder,= ++Params: pin_a GPIO connected to rotary encoder channel A ++ (default 4). ++ pin_b GPIO connected to rotary encoder channel B ++ (default 17). ++ relative_axis register a relative axis rather than an ++ absolute one. Relative axis will only ++ generate +1/-1 events on the input device, ++ hence no steps need to be passed. ++ linux_axis the input subsystem axis to map to this ++ rotary encoder. Defaults to 0 (ABS_X / REL_X) ++ rollover Automatic rollover when the rotary value ++ becomes greater than the specified steps or ++ smaller than 0. For absolute axis only. ++ steps-per-period Number of steps (stable states) per period. ++ The values have the following meaning: ++ 1: Full-period mode (default) ++ 2: Half-period mode ++ 4: Quarter-period mode ++ steps Number of steps in a full turnaround of the ++ encoder. Only relevant for absolute axis. ++ Defaults to 24 which is a typical value for ++ such devices. ++ wakeup Boolean, rotary encoder can wake up the ++ system. ++ encoding String, the method used to encode steps. ++ Supported are "gray" (the default and more ++ common) and "binary". ++ ++ ++Name: rpi-backlight ++Info: Raspberry Pi official display backlight driver ++Load: dtoverlay=rpi-backlight ++Params: ++ ++ ++Name: rpi-cirrus-wm5102 ++Info: Configures the Cirrus Logic Audio Card ++Load: dtoverlay=rpi-cirrus-wm5102 ++Params: ++ ++ ++Name: rpi-dac ++Info: Configures the RPi DAC audio card ++Load: dtoverlay=rpi-dac ++Params: ++ ++ ++Name: rpi-display ++Info: RPi-Display - 2.8" Touch Display by Watterott ++Load: dtoverlay=rpi-display,= ++Params: speed Display SPI bus speed ++ rotate Display rotation {0,90,180,270} ++ fps Delay between frame updates ++ debug Debug output level {0-7} ++ xohms Touchpanel sensitivity (X-plate resistance) ++ swapxy Swap x and y axis ++ backlight Change backlight GPIO pin {e.g. 12, 18} ++ ++ ++Name: rpi-ft5406 ++Info: Official Raspberry Pi display touchscreen ++Load: dtoverlay=rpi-ft5406,= ++Params: touchscreen-size-x Touchscreen X resolution (default 800) ++ touchscreen-size-y Touchscreen Y resolution (default 600); ++ touchscreen-inverted-x Invert touchscreen X coordinates (default 0); ++ touchscreen-inverted-y Invert touchscreen Y coordinates (default 0); ++ touchscreen-swapped-x-y Swap X and Y cordinates (default 0); ++ ++ ++Name: rpi-poe ++Info: Raspberry Pi PoE HAT fan ++Load: dtoverlay=rpi-poe,[=] ++Params: poe_fan_temp0 Temperature (in millicelcius) at which the fan ++ turns on (default 40000) ++ poe_fan_temp0_hyst Temperature delta (in millicelcius) at which ++ the fan turns off (default 2000) ++ poe_fan_temp1 Temperature (in millicelcius) at which the fan ++ speeds up (default 45000) ++ poe_fan_temp1_hyst Temperature delta (in millicelcius) at which ++ the fan slows down (default 2000) ++ poe_fan_temp2 Temperature (in millicelcius) at which the fan ++ speeds up (default 50000) ++ poe_fan_temp2_hyst Temperature delta (in millicelcius) at which ++ the fan slows down (default 2000) ++ poe_fan_temp3 Temperature (in millicelcius) at which the fan ++ speeds up (default 55000) ++ poe_fan_temp3_hyst Temperature delta (in millicelcius) at which ++ the fan slows down (default 5000) ++ ++ ++Name: rpi-proto ++Info: Configures the RPi Proto audio card ++Load: dtoverlay=rpi-proto ++Params: ++ ++ ++Name: rpi-sense ++Info: Raspberry Pi Sense HAT ++Load: dtoverlay=rpi-sense ++Params: ++ ++ ++Name: rpi-tv ++Info: Raspberry Pi TV HAT ++Load: dtoverlay=rpi-tv ++Params: ++ ++ ++Name: rpivid-v4l2 ++Info: Load the V4L2 stateless video decoder driver for the HEVC block, ++ disabling the memory mapped devices in the process. ++Load: dtoverlay=rpivid-v4l2 ++Params: ++ ++ ++Name: rra-digidac1-wm8741-audio ++Info: Configures the Red Rocks Audio DigiDAC1 soundcard ++Load: dtoverlay=rra-digidac1-wm8741-audio ++Params: ++ ++ ++Name: sainsmart18 ++Info: Overlay for the SPI-connected Sainsmart 1.8" display (based on the ++ ST7735R chip). ++Load: dtoverlay=sainsmart18,= ++Params: rotate Display rotation {0,90,180,270} ++ speed SPI bus speed in Hz (default 4000000) ++ fps Display frame rate in Hz ++ bgr Enable BGR mode (default off) ++ debug Debug output level {0-7} ++ dc_pin GPIO pin for D/C (default 24) ++ reset_pin GPIO pin for RESET (default 25) ++ ++ ++Name: sc16is750-i2c ++Info: Overlay for the NXP SC16IS750 UART with I2C Interface ++ Enables the chip on I2C1 at 0x48 (or the "addr" parameter value). To ++ select another address, please refer to table 10 in reference manual. ++Load: dtoverlay=sc16is750-i2c,= ++Params: int_pin GPIO used for IRQ (default 24) ++ addr Address (default 0x48) ++ xtal On-board crystal frequency (default 14745600) ++ ++ ++Name: sc16is752-i2c ++Info: Overlay for the NXP SC16IS752 dual UART with I2C Interface ++ Enables the chip on I2C1 at 0x48 (or the "addr" parameter value). To ++ select another address, please refer to table 10 in reference manual. ++Load: dtoverlay=sc16is752-i2c,= ++Params: int_pin GPIO used for IRQ (default 24) ++ addr Address (default 0x48) ++ xtal On-board crystal frequency (default 14745600) ++ ++ ++Name: sc16is752-spi0 ++Info: Overlay for the NXP SC16IS752 Dual UART with SPI Interface ++ Enables the chip on SPI0. ++Load: dtoverlay=sc16is752-spi0,= ++Params: int_pin GPIO used for IRQ (default 24) ++ xtal On-board crystal frequency (default 14745600) ++ ++ ++Name: sc16is752-spi1 ++Info: Overlay for the NXP SC16IS752 Dual UART with SPI Interface ++ Enables the chip on SPI1. ++ N.B.: spi1 is only accessible on devices with a 40pin header, eg: ++ A+, B+, Zero and PI2 B; as well as the Compute Module. ++ ++Load: dtoverlay=sc16is752-spi1,= ++Params: int_pin GPIO used for IRQ (default 24) ++ xtal On-board crystal frequency (default 14745600) ++ ++ ++Name: sdhost ++Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock. ++ N.B. This overlay is designed for situations where the mmc driver is ++ the default, so it disables the other (mmc) interface - this will kill ++ WiFi on a Pi3. If this isn't what you want, either use the sdtweak ++ overlay or the new sd_* dtparams of the base DTBs. ++Load: dtoverlay=sdhost,= ++Params: overclock_50 Clock (in MHz) to use when the MMC framework ++ requests 50MHz ++ ++ force_pio Disable DMA support (default off) ++ ++ pio_limit Number of blocks above which to use DMA ++ (default 1) ++ ++ debug Enable debug output (default off) ++ ++ ++Name: sdio ++Info: Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock, ++ and enables SDIO via GPIOs 22-27. An example of use in 1-bit mode is ++ "dtoverlay=sdio,bus_width=1,gpios_22_25" ++Load: dtoverlay=sdio,= ++Params: sdio_overclock SDIO Clock (in MHz) to use when the MMC ++ framework requests 50MHz ++ ++ poll_once Disable SDIO-device polling every second ++ (default on: polling once at boot-time) ++ ++ bus_width Set the SDIO host bus width (default 4 bits) ++ ++ gpios_22_25 Select GPIOs 22-25 for 1-bit mode. Must be used ++ with bus_width=1. This replaces the sdio-1bit ++ overlay, which is now deprecated. ++ ++ gpios_34_37 Select GPIOs 34-37 for 1-bit mode. Must be used ++ with bus_width=1. ++ ++ gpios_34_39 Select GPIOs 34-39 for 4-bit mode. Must be used ++ with bus_width=4 (the default). ++ ++ ++Name: sdio-1bit ++Info: This overlay is now deprecated. Use ++ "dtoverlay=sdio,bus_width=1,gpios_22_25" instead. ++Load: ++ ++ ++Name: sdtweak ++Info: Tunes the bcm2835-sdhost SD/MMC driver ++ N.B. This functionality is now available via the sd_* dtparams in the ++ base DTB. ++Load: dtoverlay=sdtweak,= ++Params: overclock_50 Clock (in MHz) to use when the MMC framework ++ requests 50MHz ++ ++ force_pio Disable DMA support (default off) ++ ++ pio_limit Number of blocks above which to use DMA ++ (default 1) ++ ++ debug Enable debug output (default off) ++ ++ poll_once Looks for a card once after booting. Useful ++ for network booting scenarios to avoid the ++ overhead of continuous polling. N.B. Using ++ this option restricts the system to using a ++ single card per boot (or none at all). ++ (default off) ++ ++ enable Set to off to completely disable the interface ++ (default on) ++ ++ ++Name: sh1106-spi ++Info: Overlay for SH1106 OLED via SPI using fbtft staging driver. ++Load: dtoverlay=sh1106-spi,= ++Params: speed SPI bus speed (default 4000000) ++ rotate Display rotation (0, 90, 180 or 270; default 0) ++ fps Delay between frame updates (default 25) ++ debug Debug output level (0-7; default 0) ++ dc_pin GPIO pin for D/C (default 24) ++ reset_pin GPIO pin for RESET (default 25) ++ height Display height (32 or 64; default 64) ++ ++ ++Name: smi ++Info: Enables the Secondary Memory Interface peripheral. Uses GPIOs 2-25! ++Load: dtoverlay=smi ++Params: ++ ++ ++Name: smi-dev ++Info: Enables the userspace interface for the SMI driver ++Load: dtoverlay=smi-dev ++Params: ++ ++ ++Name: smi-nand ++Info: Enables access to NAND flash via the SMI interface ++Load: dtoverlay=smi-nand ++Params: ++ ++ ++Name: spi-gpio35-39 ++Info: Move SPI function block to GPIO 35 to 39 ++Load: dtoverlay=spi-gpio35-39 ++Params: ++ ++ ++Name: spi-gpio40-45 ++Info: Move SPI function block to GPIOs 40 to 45 ++Load: dtoverlay=spi-gpio40-45 ++Params: ++ ++ ++Name: spi-rtc ++Info: Adds support for a number of SPI Real Time Clock devices ++Load: dtoverlay=spi-rtc,= ++Params: pcf2123 Select the PCF2123 device ++ ++ ++Name: spi0-1cs ++Info: Only use one CS pin for SPI0 ++Load: dtoverlay=spi0-1cs,= ++Params: cs0_pin GPIO pin for CS0 (default 8) ++ no_miso Don't claim and use the MISO pin (9), freeing ++ it for other uses. ++ ++ ++Name: spi0-2cs ++Info: Change the CS pins for SPI0 ++Load: dtoverlay=spi0-2cs,= ++Params: cs0_pin GPIO pin for CS0 (default 8) ++ cs1_pin GPIO pin for CS1 (default 7) ++ no_miso Don't claim and use the MISO pin (9), freeing ++ it for other uses. ++ ++ ++Name: spi0-cs ++Info: This overlay has been renamed spi0-2cs, keeping spi0-cs as an ++ alias for backwards compatibility. ++Load: ++ ++ ++Name: spi0-hw-cs ++Info: This overlay has been deprecated and removed because it is no longer ++ necessary and has been seen to prevent spi0 from working. ++Load: ++ ++ ++Name: spi1-1cs ++Info: Enables spi1 with a single chip select (CS) line and associated spidev ++ dev node. The gpio pin number for the CS line and spidev device node ++ creation are configurable. ++ N.B.: spi1 is only accessible on devices with a 40pin header, eg: ++ A+, B+, Zero and PI2 B; as well as the Compute Module. ++Load: dtoverlay=spi1-1cs,= ++Params: cs0_pin GPIO pin for CS0 (default 18 - BCM SPI1_CE0). ++ cs0_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev1.0 (default ++ is 'okay' or enabled). ++ ++ ++Name: spi1-2cs ++Info: Enables spi1 with two chip select (CS) lines and associated spidev ++ dev nodes. The gpio pin numbers for the CS lines and spidev device node ++ creation are configurable. ++ N.B.: spi1 is only accessible on devices with a 40pin header, eg: ++ A+, B+, Zero and PI2 B; as well as the Compute Module. ++Load: dtoverlay=spi1-2cs,= ++Params: cs0_pin GPIO pin for CS0 (default 18 - BCM SPI1_CE0). ++ cs1_pin GPIO pin for CS1 (default 17 - BCM SPI1_CE1). ++ cs0_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev1.0 (default ++ is 'okay' or enabled). ++ cs1_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev1.1 (default ++ is 'okay' or enabled). ++ ++ ++Name: spi1-3cs ++Info: Enables spi1 with three chip select (CS) lines and associated spidev ++ dev nodes. The gpio pin numbers for the CS lines and spidev device node ++ creation are configurable. ++ N.B.: spi1 is only accessible on devices with a 40pin header, eg: ++ A+, B+, Zero and PI2 B; as well as the Compute Module. ++Load: dtoverlay=spi1-3cs,= ++Params: cs0_pin GPIO pin for CS0 (default 18 - BCM SPI1_CE0). ++ cs1_pin GPIO pin for CS1 (default 17 - BCM SPI1_CE1). ++ cs2_pin GPIO pin for CS2 (default 16 - BCM SPI1_CE2). ++ cs0_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev1.0 (default ++ is 'okay' or enabled). ++ cs1_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev1.1 (default ++ is 'okay' or enabled). ++ cs2_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev1.2 (default ++ is 'okay' or enabled). ++ ++ ++Name: spi2-1cs ++Info: Enables spi2 with a single chip select (CS) line and associated spidev ++ dev node. The gpio pin number for the CS line and spidev device node ++ creation are configurable. ++ N.B.: spi2 is only accessible with the Compute Module. ++Load: dtoverlay=spi2-1cs,= ++Params: cs0_pin GPIO pin for CS0 (default 43 - BCM SPI2_CE0). ++ cs0_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev2.0 (default ++ is 'okay' or enabled). ++ ++ ++Name: spi2-2cs ++Info: Enables spi2 with two chip select (CS) lines and associated spidev ++ dev nodes. The gpio pin numbers for the CS lines and spidev device node ++ creation are configurable. ++ N.B.: spi2 is only accessible with the Compute Module. ++Load: dtoverlay=spi2-2cs,= ++Params: cs0_pin GPIO pin for CS0 (default 43 - BCM SPI2_CE0). ++ cs1_pin GPIO pin for CS1 (default 44 - BCM SPI2_CE1). ++ cs0_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev2.0 (default ++ is 'okay' or enabled). ++ cs1_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev2.1 (default ++ is 'okay' or enabled). ++ ++ ++Name: spi2-3cs ++Info: Enables spi2 with three chip select (CS) lines and associated spidev ++ dev nodes. The gpio pin numbers for the CS lines and spidev device node ++ creation are configurable. ++ N.B.: spi2 is only accessible with the Compute Module. ++Load: dtoverlay=spi2-3cs,= ++Params: cs0_pin GPIO pin for CS0 (default 43 - BCM SPI2_CE0). ++ cs1_pin GPIO pin for CS1 (default 44 - BCM SPI2_CE1). ++ cs2_pin GPIO pin for CS2 (default 45 - BCM SPI2_CE2). ++ cs0_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev2.0 (default ++ is 'okay' or enabled). ++ cs1_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev2.1 (default ++ is 'okay' or enabled). ++ cs2_spidev Set to 'disabled' to stop the creation of a ++ userspace device node /dev/spidev2.2 (default ++ is 'okay' or enabled). ++ ++ ++Name: spi3-1cs ++Info: Enables spi3 with a single chip select (CS) line and associated spidev ++ dev node. The gpio pin number for the CS line and spidev device node ++ creation are configurable. BCM2711 only. ++Load: dtoverlay=spi3-1cs,= ++Params: cs0_pin GPIO pin for CS0 (default 0 - BCM SPI3_CE0). ++ cs0_spidev Set to 'off' to prevent the creation of a ++ userspace device node /dev/spidev3.0 (default ++ is 'on' or enabled). ++ ++ ++Name: spi3-2cs ++Info: Enables spi3 with two chip select (CS) lines and associated spidev ++ dev nodes. The gpio pin numbers for the CS lines and spidev device node ++ creation are configurable. BCM2711 only. ++Load: dtoverlay=spi3-2cs,= ++Params: cs0_pin GPIO pin for CS0 (default 0 - BCM SPI3_CE0). ++ cs1_pin GPIO pin for CS1 (default 24 - BCM SPI3_CE1). ++ cs0_spidev Set to 'off' to prevent the creation of a ++ userspace device node /dev/spidev3.0 (default ++ is 'on' or enabled). ++ cs1_spidev Set to 'off' to prevent the creation of a ++ userspace device node /dev/spidev3.1 (default ++ is 'on' or enabled). ++ ++ ++Name: spi4-1cs ++Info: Enables spi4 with a single chip select (CS) line and associated spidev ++ dev node. The gpio pin number for the CS line and spidev device node ++ creation are configurable. BCM2711 only. ++Load: dtoverlay=spi4-1cs,= ++Params: cs0_pin GPIO pin for CS0 (default 4 - BCM SPI4_CE0). ++ cs0_spidev Set to 'off' to prevent the creation of a ++ userspace device node /dev/spidev4.0 (default ++ is 'on' or enabled). ++ ++ ++Name: spi4-2cs ++Info: Enables spi4 with two chip select (CS) lines and associated spidev ++ dev nodes. The gpio pin numbers for the CS lines and spidev device node ++ creation are configurable. BCM2711 only. ++Load: dtoverlay=spi4-2cs,= ++Params: cs0_pin GPIO pin for CS0 (default 4 - BCM SPI4_CE0). ++ cs1_pin GPIO pin for CS1 (default 25 - BCM SPI4_CE1). ++ cs0_spidev Set to 'off' to prevent the creation of a ++ userspace device node /dev/spidev4.0 (default ++ is 'on' or enabled). ++ cs1_spidev Set to 'off' to prevent the creation of a ++ userspace device node /dev/spidev4.1 (default ++ is 'on' or enabled). ++ ++ ++Name: spi5-1cs ++Info: Enables spi5 with a single chip select (CS) line and associated spidev ++ dev node. The gpio pin numbers for the CS lines and spidev device node ++ creation are configurable. BCM2711 only. ++Load: dtoverlay=spi5-1cs,= ++Params: cs0_pin GPIO pin for CS0 (default 12 - BCM SPI5_CE0). ++ cs0_spidev Set to 'off' to prevent the creation of a ++ userspace device node /dev/spidev5.0 (default ++ is 'on' or enabled). ++ ++ ++Name: spi5-2cs ++Info: Enables spi5 with two chip select (CS) lines and associated spidev ++ dev nodes. The gpio pin numbers for the CS lines and spidev device node ++ creation are configurable. BCM2711 only. ++Load: dtoverlay=spi5-2cs,= ++Params: cs0_pin GPIO pin for CS0 (default 12 - BCM SPI5_CE0). ++ cs1_pin GPIO pin for CS1 (default 26 - BCM SPI5_CE1). ++ cs0_spidev Set to 'off' to prevent the creation of a ++ userspace device node /dev/spidev5.0 (default ++ is 'on' or enabled). ++ cs1_spidev Set to 'off' to prevent the creation of a ++ userspace device node /dev/spidev5.1 (default ++ is 'on' or enabled). ++ ++ ++Name: spi6-1cs ++Info: Enables spi6 with a single chip select (CS) line and associated spidev ++ dev node. The gpio pin number for the CS line and spidev device node ++ creation are configurable. BCM2711 only. ++Load: dtoverlay=spi6-1cs,= ++Params: cs0_pin GPIO pin for CS0 (default 18 - BCM SPI6_CE0). ++ cs0_spidev Set to 'off' to prevent the creation of a ++ userspace device node /dev/spidev6.0 (default ++ is 'on' or enabled). ++ ++ ++Name: spi6-2cs ++Info: Enables spi6 with two chip select (CS) lines and associated spidev ++ dev nodes. The gpio pin numbers for the CS lines and spidev device node ++ creation are configurable. BCM2711 only. ++Load: dtoverlay=spi6-2cs,= ++Params: cs0_pin GPIO pin for CS0 (default 18 - BCM SPI6_CE0). ++ cs1_pin GPIO pin for CS1 (default 27 - BCM SPI6_CE1). ++ cs0_spidev Set to 'off' to prevent the creation of a ++ userspace device node /dev/spidev6.0 (default ++ is 'on' or enabled). ++ cs1_spidev Set to 'off' to prevent the creation of a ++ userspace device node /dev/spidev6.1 (default ++ is 'on' or enabled). ++ ++ ++Name: ssd1306 ++Info: Overlay for activation of SSD1306 over I2C OLED display framebuffer. ++Load: dtoverlay=ssd1306,= ++Params: address Location in display memory of first character. ++ (default=0) ++ width Width of display. (default=128) ++ height Height of display. (default=64) ++ offset virtual channel a. (default=0) ++ normal Has no effect on displays tested. (default=not ++ set) ++ sequential Set this if every other scan line is missing. ++ (default=not set) ++ remapped Set this if display is garbled. (default=not ++ set) ++ inverted Set this if display is inverted and mirrored. ++ (default=not set) ++ ++ Examples: ++ Typical usage for 128x64 display: dtoverlay=ssd1306,inverted ++ ++ Typical usage for 128x32 display: dtoverlay=ssd1306,inverted,sequential ++ ++ i2c_baudrate=400000 will speed up the display. ++ ++ i2c_baudrate=1000000 seems to work even though it's not officially ++ supported by the hardware, and is faster still. ++ ++ For more information refer to the device datasheet at: ++ https://cdn-shop.adafruit.com/datasheets/SSD1306.pdf ++ ++ ++Name: ssd1306-spi ++Info: Overlay for SSD1306 OLED via SPI using fbtft staging driver. ++Load: dtoverlay=ssd1306-spi,= ++Params: speed SPI bus speed (default 10000000) ++ rotate Display rotation (0, 90, 180 or 270; default 0) ++ fps Delay between frame updates (default 25) ++ debug Debug output level (0-7; default 0) ++ dc_pin GPIO pin for D/C (default 24) ++ reset_pin GPIO pin for RESET (default 25) ++ height Display height (32 or 64; default 64) ++ ++ ++Name: ssd1351-spi ++Info: Overlay for SSD1351 OLED via SPI using fbtft staging driver. ++Load: dtoverlay=ssd1351-spi,= ++Params: speed SPI bus speed (default 4500000) ++ rotate Display rotation (0, 90, 180 or 270; default 0) ++ fps Delay between frame updates (default 25) ++ debug Debug output level (0-7; default 0) ++ dc_pin GPIO pin for D/C (default 24) ++ reset_pin GPIO pin for RESET (default 25) ++ ++ ++Name: superaudioboard ++Info: Configures the SuperAudioBoard sound card ++Load: dtoverlay=superaudioboard,= ++Params: gpiopin GPIO pin for codec reset ++ ++ ++Name: sx150x ++Info: Configures the Semtech SX150X I2C GPIO expanders. ++Load: dtoverlay=sx150x,= ++Params: sx150-- Enables SX150X device on I2C# with slave ++ address . may be 1-9. may be 0 or 1. ++ Permissible values of (which is denoted in ++ hex) depend on the device variant. For SX1501, ++ SX1502, SX1504 and SX1505, may be 20 or 21. ++ For SX1503 and SX1506, may be 20. For ++ SX1507 and SX1509, may be 3E, 3F, 70 or 71. ++ For SX1508, may be 20, 21, 22 or 23. ++ ++ sx150---int-gpio ++ Integer, enables interrupts on SX150X device on ++ I2C# with slave address , specifies ++ the GPIO pin to which NINT output of SX150X is ++ connected. ++ ++ ++Name: tc358743 ++Info: Toshiba TC358743 HDMI to CSI-2 bridge chip. ++ Uses Unicam 1, which is the standard camera connector on most Pi ++ variants. ++Load: dtoverlay=tc358743,= ++Params: 4lane Use 4 lanes (only applicable to Compute Modules ++ CAM1 connector). ++ ++ link-frequency Set the link frequency. Only values of 297000000 ++ (574Mbit/s) and 486000000 (972Mbit/s - default) ++ are supported by the driver. ++ ++ ++Name: tc358743-audio ++Info: Used in combination with the tc358743-fast overlay to route the audio ++ from the TC358743 over I2S to the Pi. ++ Wiring is LRCK/WFS to GPIO 19, BCK/SCK to GPIO 18, and DATA/SD to GPIO ++ 20. ++Load: dtoverlay=tc358743-audio,= ++Params: card-name Override the default, "tc358743", card name. ++ ++ ++Name: tinylcd35 ++Info: 3.5" Color TFT Display by www.tinylcd.com ++ Options: Touch, RTC, keypad ++Load: dtoverlay=tinylcd35,= ++Params: speed Display SPI bus speed ++ ++ rotate Display rotation {0,90,180,270} ++ ++ fps Delay between frame updates ++ ++ debug Debug output level {0-7} ++ ++ touch Enable touch panel ++ ++ touchgpio Touch controller IRQ GPIO ++ ++ xohms Touchpanel: Resistance of X-plate in ohms ++ ++ rtc-pcf PCF8563 Real Time Clock ++ ++ rtc-ds DS1307 Real Time Clock ++ ++ keypad Enable keypad ++ ++ Examples: ++ Display with touchpanel, PCF8563 RTC and keypad: ++ dtoverlay=tinylcd35,touch,rtc-pcf,keypad ++ Old touch display: ++ dtoverlay=tinylcd35,touch,touchgpio=3 ++ ++ ++Name: tpm-slb9670 ++Info: Enables support for Infineon SLB9670 Trusted Platform Module add-on ++ boards, which can be used as a secure key storage and hwrng, ++ available as "Iridium SLB9670" by Infineon and "LetsTrust TPM" by pi3g. ++Load: dtoverlay=tpm-slb9670 ++Params: ++ ++ ++Name: uart0 ++Info: Change the pin usage of uart0 ++Load: dtoverlay=uart0,= ++Params: txd0_pin GPIO pin for TXD0 (14, 32 or 36 - default 14) ++ ++ rxd0_pin GPIO pin for RXD0 (15, 33 or 37 - default 15) ++ ++ pin_func Alternative pin function - 4(Alt0) for 14&15, ++ 7(Alt3) for 32&33, 6(Alt2) for 36&37 ++ ++ ++Name: uart1 ++Info: Change the pin usage of uart1 ++Load: dtoverlay=uart1,= ++Params: txd1_pin GPIO pin for TXD1 (14, 32 or 40 - default 14) ++ ++ rxd1_pin GPIO pin for RXD1 (15, 33 or 41 - default 15) ++ ++ ++Name: uart2 ++Info: Enable uart 2 on GPIOs 0-3. BCM2711 only. ++Load: dtoverlay=uart2, ++Params: ctsrts Enable CTS/RTS on GPIOs 2-3 (default off) ++ ++ ++Name: uart3 ++Info: Enable uart 3 on GPIOs 4-7. BCM2711 only. ++Load: dtoverlay=uart3, ++Params: ctsrts Enable CTS/RTS on GPIOs 6-7 (default off) ++ ++ ++Name: uart4 ++Info: Enable uart 4 on GPIOs 8-11. BCM2711 only. ++Load: dtoverlay=uart4, ++Params: ctsrts Enable CTS/RTS on GPIOs 10-11 (default off) ++ ++ ++Name: uart5 ++Info: Enable uart 5 on GPIOs 12-15. BCM2711 only. ++Load: dtoverlay=uart5, ++Params: ctsrts Enable CTS/RTS on GPIOs 14-15 (default off) ++ ++ ++Name: udrc ++Info: Configures the NW Digital Radio UDRC Hat ++Load: dtoverlay=udrc,= ++Params: alsaname Name of the ALSA audio device (default "udrc") ++ ++ ++Name: upstream ++Info: Allow usage of downstream .dtb with upstream kernel. Comprises the ++ vc4-kms-v3d and dwc2 overlays. ++Load: dtoverlay=upstream ++Params: ++ ++ ++Name: upstream-aux-interrupt ++Info: This overlay has been deprecated and removed because it is no longer ++ necessary. ++Load: ++ ++ ++Name: upstream-pi4 ++Info: Allow usage of downstream .dtb with upstream kernel on Pi 4. Comprises ++ the vc4-kms-v3d-pi4 and dwc2 overlays. ++Load: dtoverlay=upstream-pi4 ++Params: ++ ++ ++Name: vc4-fkms-v3d ++Info: Enable Eric Anholt's DRM VC4 V3D driver on top of the dispmanx ++ display stack. ++Load: dtoverlay=vc4-fkms-v3d, ++Params: cma-512 CMA is 512MB (needs 1GB) ++ cma-448 CMA is 448MB (needs 1GB) ++ cma-384 CMA is 384MB (needs 1GB) ++ cma-320 CMA is 320MB (needs 1GB) ++ cma-256 CMA is 256MB (needs 1GB) ++ cma-192 CMA is 192MB (needs 1GB) ++ cma-128 CMA is 128MB ++ cma-96 CMA is 96MB ++ cma-64 CMA is 64MB ++ cma-size CMA size in bytes, 4MB aligned ++ cma-default Use upstream's default value ++ ++ ++Name: vc4-kms-kippah-7inch ++Info: Enable the Adafruit DPI Kippah with the 7" Ontat panel attached. ++ Requires vc4-kms-v3d to be loaded. ++Load: dtoverlay=vc4-kms-kippah-7inch ++Params: ++ ++ ++Name: vc4-kms-v3d ++Info: Enable Eric Anholt's DRM VC4 HDMI/HVS/V3D driver. ++Load: dtoverlay=vc4-kms-v3d, ++Params: cma-512 CMA is 512MB (needs 1GB) ++ cma-448 CMA is 448MB (needs 1GB) ++ cma-384 CMA is 384MB (needs 1GB) ++ cma-320 CMA is 320MB (needs 1GB) ++ cma-256 CMA is 256MB (needs 1GB) ++ cma-192 CMA is 192MB (needs 1GB) ++ cma-128 CMA is 128MB ++ cma-96 CMA is 96MB ++ cma-64 CMA is 64MB ++ cma-size CMA size in bytes, 4MB aligned ++ cma-default Use upstream's default value ++ audio Enable or disable audio over HDMI (default "on") ++ noaudio Disable all HDMI audio (default "off") ++ ++ ++Name: vc4-kms-v3d-pi4 ++Info: Enable Eric Anholt's DRM VC4 HDMI/HVS/V3D driver for Pi4. ++Load: dtoverlay=vc4-kms-v3d-pi4, ++Params: cma-512 CMA is 512MB ++ cma-448 CMA is 448MB ++ cma-384 CMA is 384MB ++ cma-320 CMA is 320MB ++ cma-256 CMA is 256MB ++ cma-192 CMA is 192MB ++ cma-128 CMA is 128MB ++ cma-96 CMA is 96MB ++ cma-64 CMA is 64MB ++ cma-size CMA size in bytes, 4MB aligned ++ cma-default Use upstream's default value ++ audio Enable or disable audio over HDMI0 (default ++ "on") ++ audio1 Enable or disable audio over HDMI1 (default ++ "on") ++ noaudio Disable all HDMI audio (default "off") ++ composite Enable the composite output (disables all other ++ outputs) ++ ++ ++Name: vga666 ++Info: Overlay for the Fen Logic VGA666 board ++ This uses GPIOs 2-21 (so no I2C), and activates the output 2-3 seconds ++ after the kernel has started. ++Load: dtoverlay=vga666 ++Params: ++ ++ ++Name: w1-gpio ++Info: Configures the w1-gpio Onewire interface module. ++ Use this overlay if you *don't* need a GPIO to drive an external pullup. ++Load: dtoverlay=w1-gpio,= ++Params: gpiopin GPIO for I/O (default "4") ++ pullup Now enabled by default (ignored) ++ ++ ++Name: w1-gpio-pullup ++Info: Configures the w1-gpio Onewire interface module. ++ Use this overlay if you *do* need a GPIO to drive an external pullup. ++Load: dtoverlay=w1-gpio-pullup,= ++Params: gpiopin GPIO for I/O (default "4") ++ extpullup GPIO for external pullup (default "5") ++ pullup Now enabled by default (ignored) ++ ++ ++Name: w5500 ++Info: Overlay for the Wiznet W5500 Ethernet Controller on SPI0 ++Load: dtoverlay=w5500,= ++Params: int_pin GPIO used for INT (default 25) ++ ++ speed SPI bus speed (default 30000000) ++ ++ cs SPI bus Chip Select (default 0) ++ ++ ++Name: wittypi ++Info: Configures the wittypi RTC module. ++Load: dtoverlay=wittypi,= ++Params: led_gpio GPIO for LED (default "17") ++ led_trigger Choose which activity the LED tracks (default ++ "default-on") ++ ++ ++Troubleshooting ++=============== ++ ++If you are experiencing problems that you think are DT-related, enable DT ++diagnostic output by adding this to /boot/config.txt: ++ ++ dtdebug=on ++ ++and rebooting. Then run: ++ ++ sudo vcdbg log msg ++ ++and look for relevant messages. ++ ++Further reading ++=============== ++ ++This is only meant to be a quick introduction to the subject of Device Tree on ++Raspberry Pi. There is a more complete explanation here: ++ ++http://www.raspberrypi.org/documentation/configuration/device-tree.md +diff --git a/arch/arm/boot/dts/overlays/act-led-overlay.dts b/arch/arm/boot/dts/overlays/act-led-overlay.dts +new file mode 100644 +index 000000000000..2f4bbb407f89 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/act-led-overlay.dts +@@ -0,0 +1,27 @@ ++/dts-v1/; ++/plugin/; ++ ++/* Pi3 uses a GPIO expander to drive the LEDs which can only be accessed ++ from the VPU. There is a special driver for this with a separate DT node, ++ which has the unfortunate consequence of breaking the act_led_gpio and ++ act_led_activelow dtparams. ++ ++ This overlay changes the GPIO controller back to the standard one and ++ restores the dtparams. ++*/ ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&act_led>; ++ frag0: __overlay__ { ++ gpios = <&gpio 0 0>; ++ }; ++ }; ++ ++ __overrides__ { ++ gpio = <&frag0>,"gpios:4"; ++ activelow = <&frag0>,"gpios:8"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/adafruit18-overlay.dts b/arch/arm/boot/dts/overlays/adafruit18-overlay.dts +new file mode 100644 +index 000000000000..e1ce94a8cd3e +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/adafruit18-overlay.dts +@@ -0,0 +1,55 @@ ++/* ++ * Device Tree overlay for Adafruit 1.8" TFT LCD with ST7735R chip 160x128 ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ af18: adafruit18@0 { ++ compatible = "fbtft,adafruit18"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ spi-max-frequency = <40000000>; ++ rotate = <90>; ++ buswidth = <8>; ++ fps = <50>; ++ height = <160>; ++ width = <128>; ++ reset-gpios = <&gpio 25 1>; ++ dc-gpios = <&gpio 24 0>; ++ led-gpios = <&gpio 18 0>; ++ debug = <0>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ green = <&af18>, "compatible=fbtft,adafruit18_green"; ++ speed = <&af18>,"spi-max-frequency:0"; ++ rotate = <&af18>,"rotate:0"; ++ fps = <&af18>,"fps:0"; ++ bgr = <&af18>,"bgr?"; ++ debug = <&af18>,"debug:0"; ++ dc_pin = <&af18>,"dc-gpios:4"; ++ reset_pin = <&af18>,"reset-gpios:4"; ++ led_pin = <&af18>,"led-gpios:4"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/adau1977-adc-overlay.dts b/arch/arm/boot/dts/overlays/adau1977-adc-overlay.dts +new file mode 100644 +index 000000000000..298488e19156 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/adau1977-adc-overlay.dts +@@ -0,0 +1,40 @@ ++// Definitions for ADAU1977 ADC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c>; ++ ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ adau1977: codec@11 { ++ compatible = "adi,adau1977"; ++ reg = <0x11>; ++ reset-gpios = <&gpio 5 0>; ++ AVDD-supply = <&vdd_3v3_reg>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "adi,adau1977-adc"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/adau7002-simple-overlay.dts b/arch/arm/boot/dts/overlays/adau7002-simple-overlay.dts +new file mode 100644 +index 000000000000..5fed769d2526 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/adau7002-simple-overlay.dts +@@ -0,0 +1,52 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ adau7002_codec: adau7002-codec { ++ #sound-dai-cells = <0>; ++ compatible = "adi,adau7002"; ++/* IOVDD-supply = <&supply>;*/ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ sound_overlay: __overlay__ { ++ compatible = "simple-audio-card"; ++ simple-audio-card,format = "i2s"; ++ simple-audio-card,name = "adau7002"; ++ simple-audio-card,bitclock-slave = <&dailink0_slave>; ++ simple-audio-card,frame-slave = <&dailink0_slave>; ++ simple-audio-card,widgets = ++ "Microphone", "Microphone Jack"; ++ simple-audio-card,routing = ++ "PDM_DAT", "Microphone Jack"; ++ status = "okay"; ++ simple-audio-card,cpu { ++ sound-dai = <&i2s>; ++ }; ++ dailink0_slave: simple-audio-card,codec { ++ sound-dai = <&adau7002_codec>; ++ }; ++ }; ++ }; ++ ++ ++ __overrides__ { ++ card-name = <&sound_overlay>,"simple-audio-card,name"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/ads1015-overlay.dts b/arch/arm/boot/dts/overlays/ads1015-overlay.dts +new file mode 100644 +index 000000000000..deeee1228395 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ads1015-overlay.dts +@@ -0,0 +1,98 @@ ++/* ++ * 2016 - Erik Sejr ++ */ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ /* ----------- ADS1015 ------------ */ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ads1015: ads1015 { ++ compatible = "ti,ads1015"; ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <0x48>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&ads1015>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ channel_a: channel_a { ++ reg = <4>; ++ ti,gain = <2>; ++ ti,datarate = <4>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&ads1015>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ channel_b: channel_b { ++ reg = <5>; ++ ti,gain = <2>; ++ ti,datarate = <4>; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&ads1015>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ channel_c: channel_c { ++ reg = <6>; ++ ti,gain = <2>; ++ ti,datarate = <4>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&ads1015>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ channel_d: channel_d { ++ reg = <7>; ++ ti,gain = <2>; ++ ti,datarate = <4>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ addr = <&ads1015>,"reg:0"; ++ cha_enable = <0>,"=1"; ++ cha_cfg = <&channel_a>,"reg:0"; ++ cha_gain = <&channel_a>,"ti,gain:0"; ++ cha_datarate = <&channel_a>,"ti,datarate:0"; ++ chb_enable = <0>,"=2"; ++ chb_cfg = <&channel_b>,"reg:0"; ++ chb_gain = <&channel_b>,"ti,gain:0"; ++ chb_datarate = <&channel_b>,"ti,datarate:0"; ++ chc_enable = <0>,"=3"; ++ chc_cfg = <&channel_c>,"reg:0"; ++ chc_gain = <&channel_c>,"ti,gain:0"; ++ chc_datarate = <&channel_c>,"ti,datarate:0"; ++ chd_enable = <0>,"=4"; ++ chd_cfg = <&channel_d>,"reg:0"; ++ chd_gain = <&channel_d>,"ti,gain:0"; ++ chd_datarate = <&channel_d>,"ti,datarate:0"; ++ }; ++ ++}; +diff --git a/arch/arm/boot/dts/overlays/ads1115-overlay.dts b/arch/arm/boot/dts/overlays/ads1115-overlay.dts +new file mode 100644 +index 000000000000..4fc571c2db33 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ads1115-overlay.dts +@@ -0,0 +1,103 @@ ++/* ++ * TI ADS1115 multi-channel ADC overlay ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ads1115: ads1115 { ++ compatible = "ti,ads1115"; ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <0x48>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&ads1115>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ channel_a: channel_a { ++ reg = <4>; ++ ti,gain = <1>; ++ ti,datarate = <7>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&ads1115>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ channel_b: channel_b { ++ reg = <5>; ++ ti,gain = <1>; ++ ti,datarate = <7>; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&ads1115>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ channel_c: channel_c { ++ reg = <6>; ++ ti,gain = <1>; ++ ti,datarate = <7>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&ads1115>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ channel_d: channel_d { ++ reg = <7>; ++ ti,gain = <1>; ++ ti,datarate = <7>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ addr = <&ads1115>,"reg:0"; ++ cha_enable = <0>,"=1"; ++ cha_cfg = <&channel_a>,"reg:0"; ++ cha_gain = <&channel_a>,"ti,gain:0"; ++ cha_datarate = <&channel_a>,"ti,datarate:0"; ++ chb_enable = <0>,"=2"; ++ chb_cfg = <&channel_b>,"reg:0"; ++ chb_gain = <&channel_b>,"ti,gain:0"; ++ chb_datarate = <&channel_b>,"ti,datarate:0"; ++ chc_enable = <0>,"=3"; ++ chc_cfg = <&channel_c>,"reg:0"; ++ chc_gain = <&channel_c>,"ti,gain:0"; ++ chc_datarate = <&channel_c>,"ti,datarate:0"; ++ chd_enable = <0>,"=4"; ++ chd_cfg = <&channel_d>,"reg:0"; ++ chd_gain = <&channel_d>,"ti,gain:0"; ++ chd_datarate = <&channel_d>,"ti,datarate:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/ads7846-overlay.dts b/arch/arm/boot/dts/overlays/ads7846-overlay.dts +new file mode 100644 +index 000000000000..1c5c9b6bb6ff +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ads7846-overlay.dts +@@ -0,0 +1,89 @@ ++/* ++ * Generic Device Tree overlay for the ADS7846 touch controller ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ ads7846_pins: ads7846_pins { ++ brcm,pins = <255>; /* illegal default value */ ++ brcm,function = <0>; /* in */ ++ brcm,pull = <0>; /* none */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ ads7846: ads7846@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&ads7846_pins>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <255 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 255 0>; ++ ++ /* driver defaults */ ++ ti,x-min = /bits/ 16 <0>; ++ ti,y-min = /bits/ 16 <0>; ++ ti,x-max = /bits/ 16 <0x0FFF>; ++ ti,y-max = /bits/ 16 <0x0FFF>; ++ ti,pressure-min = /bits/ 16 <0>; ++ ti,pressure-max = /bits/ 16 <0xFFFF>; ++ ti,x-plate-ohms = /bits/ 16 <400>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ cs = <&ads7846>,"reg:0"; ++ speed = <&ads7846>,"spi-max-frequency:0"; ++ penirq = <&ads7846_pins>,"brcm,pins:0", /* REQUIRED */ ++ <&ads7846>,"interrupts:0", ++ <&ads7846>,"pendown-gpio:4"; ++ penirq_pull = <&ads7846_pins>,"brcm,pull:0"; ++ swapxy = <&ads7846>,"ti,swap-xy?"; ++ xmin = <&ads7846>,"ti,x-min;0"; ++ ymin = <&ads7846>,"ti,y-min;0"; ++ xmax = <&ads7846>,"ti,x-max;0"; ++ ymax = <&ads7846>,"ti,y-max;0"; ++ pmin = <&ads7846>,"ti,pressure-min;0"; ++ pmax = <&ads7846>,"ti,pressure-max;0"; ++ xohms = <&ads7846>,"ti,x-plate-ohms;0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/adv7282m-overlay.dts b/arch/arm/boot/dts/overlays/adv7282m-overlay.dts +new file mode 100644 +index 000000000000..5d85dfd0595c +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/adv7282m-overlay.dts +@@ -0,0 +1,65 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Definitions for Analog Devices ADV7282-M video to CSI2 bridge on VC I2C bus ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_csi_dsi>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ adv728x: adv728x@21 { ++ compatible = "adi,adv7282-m"; ++ reg = <0x21>; ++ status = "okay"; ++ clock-frequency = <24000000>; ++ port { ++ adv728x_0: endpoint { ++ remote-endpoint = <&csi1_ep>; ++ clock-lanes = <0>; ++ data-lanes = <1>; ++ link-frequencies = ++ /bits/ 64 <297000000>; ++ ++ mclk-frequency = <12000000>; ++ }; ++ }; ++ }; ++ }; ++ }; ++ fragment@1 { ++ target = <&csi1>; ++ __overlay__ { ++ status = "okay"; ++ ++ port { ++ csi1_ep: endpoint { ++ remote-endpoint = <&adv728x_0>; ++ data-lanes = <1>; ++ }; ++ }; ++ }; ++ }; ++ fragment@2 { ++ target = <&i2c0if>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c0mux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ addr = <&adv728x>,"reg:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/adv728x-m-overlay.dts b/arch/arm/boot/dts/overlays/adv728x-m-overlay.dts +new file mode 100644 +index 000000000000..ea392e886984 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/adv728x-m-overlay.dts +@@ -0,0 +1,37 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Definitions for Analog Devices ADV728[0|1|2]-M video to CSI2 bridges on VC ++// I2C bus ++ ++#include "adv7282m-overlay.dts" ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ // Fragment numbers deliberately high to avoid conflicts with the ++ // included adv7282m overlay file. ++ ++ fragment@101 { ++ target = <&adv728x>; ++ __dormant__ { ++ compatible = "adi,adv7280-m"; ++ }; ++ }; ++ fragment@102 { ++ target = <&adv728x>; ++ __dormant__ { ++ compatible = "adi,adv7281-m"; ++ }; ++ }; ++ fragment@103 { ++ target = <&adv728x>; ++ __dormant__ { ++ compatible = "adi,adv7281-ma"; ++ }; ++ }; ++ ++ __overrides__ { ++ adv7280m = <0>, "+101"; ++ adv7281m = <0>, "+102"; ++ adv7281ma = <0>, "+103"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/akkordion-iqdacplus-overlay.dts b/arch/arm/boot/dts/overlays/akkordion-iqdacplus-overlay.dts +new file mode 100644 +index 000000000000..82f9b3734fb1 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/akkordion-iqdacplus-overlay.dts +@@ -0,0 +1,49 @@ ++// Definitions for Digital Dreamtime Akkordion using IQaudIO DAC+ or DACZero ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4c { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4c>; ++ AVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ CPVDD-supply = <&vdd_3v3_reg>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ frag2: __overlay__ { ++ compatible = "iqaudio,iqaudio-dac"; ++ card_name = "Akkordion"; ++ dai_name = "IQaudIO DAC"; ++ dai_stream_name = "IQaudIO DAC HiFi"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = <&frag2>,"iqaudio,24db_digital_gain?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/allo-boss-dac-pcm512x-audio-overlay.dts b/arch/arm/boot/dts/overlays/allo-boss-dac-pcm512x-audio-overlay.dts +new file mode 100644 +index 000000000000..873cb2fab52b +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/allo-boss-dac-pcm512x-audio-overlay.dts +@@ -0,0 +1,59 @@ ++/* ++ * Definitions for Allo Boss DAC board ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ boss_osc: boss_osc { ++ compatible = "allo,dac-clk"; ++ #clock-cells = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4d { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ clocks = <&boss_osc>; ++ reg = <0x4d>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sound>; ++ boss_dac: __overlay__ { ++ compatible = "allo,boss-dac"; ++ i2s-controller = <&i2s>; ++ mute-gpios = <&gpio 6 1>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = <&boss_dac>,"allo,24db_digital_gain?"; ++ slave = <&boss_dac>,"allo,slave?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/allo-digione-overlay.dts b/arch/arm/boot/dts/overlays/allo-digione-overlay.dts +new file mode 100644 +index 000000000000..ea018ace34d4 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/allo-digione-overlay.dts +@@ -0,0 +1,44 @@ ++// Definitions for Allo DigiOne ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8804@3b { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8804"; ++ reg = <0x3b>; ++ PVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ status = "okay"; ++ wlf,reset-gpio = <&gpio 17 0>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "allo,allo-digione"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ clock44-gpio = <&gpio 5 0>; ++ clock48-gpio = <&gpio 6 0>; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/allo-katana-dac-audio-overlay.dts b/arch/arm/boot/dts/overlays/allo-katana-dac-audio-overlay.dts +new file mode 100644 +index 000000000000..b25fd681f09f +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/allo-katana-dac-audio-overlay.dts +@@ -0,0 +1,57 @@ ++/* ++ * Definitions for Allo Katana DAC boards ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ #sound-dai-cells = <0>; ++ status = "okay"; ++ cpu_port: port { ++ cpu_endpoint: endpoint { ++ remote-endpoint = <&codec_endpoint>; ++ bitclock-master = <&codec_endpoint>; ++ frame-master = <&codec_endpoint>; ++ dai-format = "i2s"; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ allo-katana-codec@30 { ++ #sound-dai-cells = <0>; ++ compatible = "allo,allo-katana-codec"; ++ reg = <0x30>; ++ port { ++ codec_endpoint: endpoint { ++ remote-endpoint = <&cpu_endpoint>; ++ }; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ katana_dac: __overlay__ { ++ compatible = "audio-graph-card"; ++ label = "Allo Katana"; ++ dais = <&cpu_port>; ++ status = "okay"; ++ }; ++ }; ++}; ++ +diff --git a/arch/arm/boot/dts/overlays/allo-piano-dac-pcm512x-audio-overlay.dts b/arch/arm/boot/dts/overlays/allo-piano-dac-pcm512x-audio-overlay.dts +new file mode 100644 +index 000000000000..bfc66da6295a +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/allo-piano-dac-pcm512x-audio-overlay.dts +@@ -0,0 +1,54 @@ ++/* ++ * Definitions for Allo Piano DAC (2.0/2.1) boards ++ * ++ * NB. The Piano DAC 2.1 board contains 2x TI PCM5142 DAC's. One DAC is stereo ++ * (left/right) and the other provides a subwoofer output, using DSP on the ++ * chip for digital high/low pass crossover. ++ * The initial support for this hardware, that doesn't require any codec driver ++ * modifications, uses only one DAC chip for stereo (left/right) output, the ++ * chip with 0x4c slave address. The other chip at 0x4d is currently ignored! ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5142@4c { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5142"; ++ reg = <0x4c>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ piano_dac: __overlay__ { ++ compatible = "allo,piano-dac"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = ++ <&piano_dac>,"allo,24db_digital_gain?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/allo-piano-dac-plus-pcm512x-audio-overlay.dts b/arch/arm/boot/dts/overlays/allo-piano-dac-plus-pcm512x-audio-overlay.dts +new file mode 100644 +index 000000000000..374c553db062 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/allo-piano-dac-plus-pcm512x-audio-overlay.dts +@@ -0,0 +1,55 @@ ++// Definitions for Piano DAC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ allo_pcm5122_4c: pcm5122@4c { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4c>; ++ status = "okay"; ++ }; ++ allo_pcm5122_4d: pcm5122@4d { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4d>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ piano_dac: __overlay__ { ++ compatible = "allo,piano-dac-plus"; ++ audio-codec = <&allo_pcm5122_4c &allo_pcm5122_4d>; ++ i2s-controller = <&i2s>; ++ mute1-gpios = <&gpio 6 1>; ++ mute2-gpios = <&gpio 25 1>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = ++ <&piano_dac>,"allo,24db_digital_gain?"; ++ glb_mclk = ++ <&piano_dac>,"allo,glb_mclk?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/anyspi-overlay.dts b/arch/arm/boot/dts/overlays/anyspi-overlay.dts +new file mode 100755 +index 000000000000..87523dcca318 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/anyspi-overlay.dts +@@ -0,0 +1,205 @@ ++/* ++ * Universal device tree overlay for SPI devices ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spidev0>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev1>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "spi1/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path = "spi1/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@4 { ++ target-path = "spi1/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path = "spi2/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@6 { ++ target-path = "spi2/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@7 { ++ target-path = "spi2/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@8 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ anyspi_00: anyspi@0 { ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ fragment@9 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ anyspi_01: anyspi@1 { ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ fragment@10 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ anyspi_10: anyspi@0 { ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ fragment@11 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ anyspi_11: anyspi@1 { ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ fragment@12 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ anyspi_12: anyspi@2 { ++ reg = <2>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ fragment@13 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ anyspi_20: anyspi@0 { ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ fragment@14 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ anyspi_21: anyspi@1 { ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ fragment@15 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ anyspi_22: anyspi@2 { ++ reg = <2>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ spi0-0 = <0>, "+0+8"; ++ spi0-1 = <0>, "+1+9"; ++ spi1-0 = <0>, "+2+10"; ++ spi1-1 = <0>, "+3+11"; ++ spi1-2 = <0>, "+4+12"; ++ spi2-0 = <0>, "+5+13"; ++ spi2-1 = <0>, "+6+14"; ++ spi2-2 = <0>, "+7+15"; ++ dev = <&anyspi_00>,"compatible", ++ <&anyspi_01>,"compatible", ++ <&anyspi_10>,"compatible", ++ <&anyspi_11>,"compatible", ++ <&anyspi_12>,"compatible", ++ <&anyspi_20>,"compatible", ++ <&anyspi_21>,"compatible", ++ <&anyspi_22>,"compatible"; ++ speed = <&anyspi_00>, "spi-max-frequency:0", ++ <&anyspi_01>, "spi-max-frequency:0", ++ <&anyspi_10>, "spi-max-frequency:0", ++ <&anyspi_11>, "spi-max-frequency:0", ++ <&anyspi_12>, "spi-max-frequency:0", ++ <&anyspi_20>, "spi-max-frequency:0", ++ <&anyspi_21>, "spi-max-frequency:0", ++ <&anyspi_22>, "spi-max-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/apds9960-overlay.dts b/arch/arm/boot/dts/overlays/apds9960-overlay.dts +new file mode 100644 +index 000000000000..c216932278ab +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/apds9960-overlay.dts +@@ -0,0 +1,57 @@ ++// Definitions for APDS-9960 ambient light and gesture sensor ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c1>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ apds9960_pins: apds9960_pins@39 { ++ brcm,pins = <4>; ++ brcm,function = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ apds9960: apds@39 { ++ compatible = "avago,apds9960"; ++ reg = <0x39>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c1>; ++ __overlay__ { ++ apds9960_irq: apds@39 { ++ #interrupt-cells=<2>; ++ interrupt-parent = <&gpio>; ++ interrupts = <4 1>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpiopin = <&apds9960_pins>,"brcm,pins:0", ++ <&apds9960_irq>,"interrupts:0"; ++ noints = <0>,"!1!3"; ++ }; ++}; ++ +diff --git a/arch/arm/boot/dts/overlays/applepi-dac-overlay.dts b/arch/arm/boot/dts/overlays/applepi-dac-overlay.dts +new file mode 100644 +index 000000000000..4769296ec9d6 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/applepi-dac-overlay.dts +@@ -0,0 +1,57 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "simple-audio-card"; ++ simple-audio-card,name = "ApplePi-DAC"; ++ ++ status = "okay"; ++ ++ playback_link: simple-audio-card,dai-link@1 { ++ format = "i2s"; ++ ++ p_cpu_dai: cpu { ++ sound-dai = <&i2s>; ++ dai-tdm-slot-num = <2>; ++ dai-tdm-slot-width = <32>; ++ }; ++ ++ p_codec_dai: codec { ++ sound-dai = <&codec_out>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ codec_out: pcm1794a-codec { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm1794a"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2s>; ++ __overlay__ { ++ #sound-dai-cells = <0>; ++ status = "okay"; ++ }; ++ }; ++}; ++ ++/* ++ Written by: Leonid Ayzenshtat ++ Company: Orchard Audio (www.orchardaudio.com) ++ ++ compile with: ++ dtc -@ -H epapr -O dtb -o ApplePi-DAC.dtbo -W no-unit_address_vs_reg ApplePi-DAC.dts ++*/ +diff --git a/arch/arm/boot/dts/overlays/at86rf233-overlay.dts b/arch/arm/boot/dts/overlays/at86rf233-overlay.dts +new file mode 100644 +index 000000000000..5a3f4571ee78 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/at86rf233-overlay.dts +@@ -0,0 +1,57 @@ ++/dts-v1/; ++/plugin/; ++ ++/* Overlay for Atmel AT86RF233 IEEE 802.15.4 WPAN transceiver on spi0.0 */ ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ lowpan0: at86rf233@0 { ++ compatible = "atmel,at86rf233"; ++ reg = <0>; ++ interrupt-parent = <&gpio>; ++ interrupts = <23 4>; /* active high */ ++ reset-gpio = <&gpio 24 1>; ++ sleep-gpio = <&gpio 25 1>; ++ spi-max-frequency = <3000000>; ++ xtal-trim = /bits/ 8 <0xf>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ lowpan0_pins: lowpan0_pins { ++ brcm,pins = <23 24 25>; ++ brcm,function = <0 1 1>; /* in out out */ ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ interrupt = <&lowpan0>, "interrupts:0", ++ <&lowpan0_pins>, "brcm,pins:0"; ++ reset = <&lowpan0>, "reset-gpio:4", ++ <&lowpan0_pins>, "brcm,pins:4"; ++ sleep = <&lowpan0>, "sleep-gpio:4", ++ <&lowpan0_pins>, "brcm,pins:8"; ++ speed = <&lowpan0>, "spi-max-frequency:0"; ++ trim = <&lowpan0>, "xtal-trim.0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/audioinjector-addons-overlay.dts b/arch/arm/boot/dts/overlays/audioinjector-addons-overlay.dts +new file mode 100644 +index 000000000000..57a66eac8e9b +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/audioinjector-addons-overlay.dts +@@ -0,0 +1,60 @@ ++// Definitions for audioinjector.net audio add on soundcard ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ cs42448_mclk: codec-mclk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <49152000>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ cs42448: cs42448@48 { ++ #sound-dai-cells = <0>; ++ compatible = "cirrus,cs42448"; ++ reg = <0x48>; ++ clocks = <&cs42448_mclk>; ++ clock-names = "mclk"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sound>; ++ snd: __overlay__ { ++ compatible = "ai,audioinjector-octo-soundcard"; ++ mult-gpios = <&gpio 27 0>, <&gpio 22 0>, <&gpio 23 0>, ++ <&gpio 24 0>; ++ reset-gpios = <&gpio 5 0>; ++ i2s-controller = <&i2s>; ++ codec = <&cs42448>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ non-stop-clocks = <&snd>, "non-stop-clocks?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/audioinjector-isolated-soundcard-overlay.dts b/arch/arm/boot/dts/overlays/audioinjector-isolated-soundcard-overlay.dts +new file mode 100644 +index 000000000000..63e05cf9665d +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/audioinjector-isolated-soundcard-overlay.dts +@@ -0,0 +1,55 @@ ++// Definitions for audioinjector.net audio isolated soundcard ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ cs4272_mclk: codec-mclk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <24576000>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ cs4272: cs4271@10 { ++ #sound-dai-cells = <0>; ++ compatible = "cirrus,cs4271"; ++ reg = <0x10>; ++ reset-gpio = <&gpio 5 0>; ++ clocks = <&cs4272_mclk>; ++ clock-names = "mclk"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sound>; ++ snd: __overlay__ { ++ compatible = "ai,audioinjector-isolated-soundcard"; ++ mute-gpios = <&gpio 17 0>; ++ i2s-controller = <&i2s>; ++ codec = <&cs4272>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/audioinjector-ultra-overlay.dts b/arch/arm/boot/dts/overlays/audioinjector-ultra-overlay.dts +new file mode 100644 +index 000000000000..fb4a4678a17a +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/audioinjector-ultra-overlay.dts +@@ -0,0 +1,71 @@ ++// Definitions for audioinjector.net audio add on soundcard ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ cs4265: cs4265@4e { ++ #sound-dai-cells = <0>; ++ compatible = "cirrus,cs4265"; ++ reg = <0x4e>; ++ reset-gpios = <&gpio 5 0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "simple-audio-card"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ ++ simple-audio-card,name = "audioinjector-ultra"; ++ ++ simple-audio-card,widgets = ++ "Line", "OUTPUTS", ++ "Line", "INPUTS"; ++ ++ simple-audio-card,routing = ++ "OUTPUTS","LINEOUTL", ++ "OUTPUTS","LINEOUTR", ++ "OUTPUTS","SPDIFOUT", ++ "LINEINL","INPUTS", ++ "LINEINR","INPUTS", ++ "MICL","INPUTS", ++ "MICR","INPUTS"; ++ ++ simple-audio-card,format = "i2s"; ++ ++ simple-audio-card,bitclock-master = <&sound_master>; ++ simple-audio-card,frame-master = <&sound_master>; ++ ++ simple-audio-card,cpu { ++ sound-dai = <&i2s>; ++ dai-tdm-slot-num = <2>; ++ dai-tdm-slot-width = <32>; ++ }; ++ ++ sound_master: simple-audio-card,codec { ++ sound-dai = <&cs4265>; ++ system-clock-frequency = <12288000>; ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/audioinjector-wm8731-audio-overlay.dts b/arch/arm/boot/dts/overlays/audioinjector-wm8731-audio-overlay.dts +new file mode 100644 +index 000000000000..68f4427d86c3 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/audioinjector-wm8731-audio-overlay.dts +@@ -0,0 +1,39 @@ ++// Definitions for audioinjector.net audio add on soundcard ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8731@1a { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8731"; ++ reg = <0x1a>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "ai,audioinjector-pi-soundcard"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/audiosense-pi-overlay.dts b/arch/arm/boot/dts/overlays/audiosense-pi-overlay.dts +new file mode 100644 +index 000000000000..81af26374d92 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/audiosense-pi-overlay.dts +@@ -0,0 +1,82 @@ ++// Definitions for audiosense add on soundcard ++/dts-v1/; ++/plugin/; ++#include ++#include ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ codec_reg_1v8: codec-reg-1v8 { ++ compatible = "regulator-fixed"; ++ regulator-name = "tlv320aic3204_1v8"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ regulator-always-on; ++ }; ++ ++ /* audio external oscillator */ ++ codec_osc: codec_osc { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <12000000>; /* 12 MHz */ ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ codec_rst: codec-rst { ++ brcm,pins = <26>; ++ brcm,function = ; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ codec: tlv320aic32x4@18 { ++ #sound-dai-cells = <0>; ++ compatible = "ti,tlv320aic32x4"; ++ reg = <0x18>; ++ ++ clocks = <&codec_osc>; ++ clock-names = "mclk"; ++ ++ iov-supply = <&vdd_3v3_reg>; ++ ldoin-supply = <&vdd_3v3_reg>; ++ ++ gpio-controller; ++ #gpio-cells = <2>; ++ reset-gpios = <&gpio 26 GPIO_ACTIVE_HIGH>; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "as,audiosense-pi"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/audremap-overlay.dts b/arch/arm/boot/dts/overlays/audremap-overlay.dts +new file mode 100644 +index 000000000000..d624bb3a3fea +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/audremap-overlay.dts +@@ -0,0 +1,35 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&audio_pins>; ++ frag0: __overlay__ { ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&audio_pins>; ++ __overlay__ { ++ brcm,pins = < 12 13 >; ++ brcm,function = < 4 >; /* alt0 alt0 */ ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&audio_pins>; ++ __dormant__ { ++ brcm,pins = < 18 19 >; ++ brcm,function = < 2 >; /* alt5 alt5 */ ++ }; ++ }; ++ ++ __overrides__ { ++ swap_lr = <&frag0>, "swap_lr?"; ++ enable_jack = <&frag0>, "enable_jack?"; ++ pins_12_13 = <0>,"+1-2"; ++ pins_18_19 = <0>,"-1+2"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/balena-fin-overlay.dts b/arch/arm/boot/dts/overlays/balena-fin-overlay.dts +new file mode 100644 +index 000000000000..e7ead7cdf5f5 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/balena-fin-overlay.dts +@@ -0,0 +1,125 @@ ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&mmcnr>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdio_pins>; ++ bus-width = <4>; ++ brcm,overclock-50 = <35>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ sdio_pins: sdio_pins { ++ brcm,pins = <34 35 36 37 38 39>; ++ brcm,function = <7>; /* ALT3 = SD1 */ ++ brcm,pull = <0 2 2 2 2 2>; ++ }; ++ ++ power_ctrl_pins: power_ctrl_pins { ++ brcm,pins = <40>; ++ brcm,function = <1>; // out ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "/"; ++ __overlay__ { ++ // We should switch to mmc-pwrseq-sd8787 after making it ++ // compatible with sd8887 ++ // Currently that module requires two GPIOs to function since it ++ // targets a slightly different chip ++ power_ctrl: power_ctrl { ++ compatible = "gpio-poweroff"; ++ gpios = <&gpio 40 1>; ++ force; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&power_ctrl_pins>; ++ }; ++ ++ i2c_soft: i2c@0 { ++ compatible = "i2c-gpio"; ++ gpios = <&gpio 43 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN) /* sda */ ++ &gpio 42 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN) /* scl */>; ++ i2c-gpio,delay-us = <5>; ++ i2c-gpio,scl-open-drain; ++ i2c-gpio,sda-open-drain; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ }; ++ ++ sd8xxx-wlan { ++ drvdbg = <0x6>; ++ drv_mode = <0x1>; ++ cfg80211_wext = <0xf>; ++ sta_name = "wlan"; ++ wfd_name = "p2p"; ++ cal_data_cfg = "none"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c_soft>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ gpio_expander: gpio_expander@20 { ++ compatible = "nxp,pca9554"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ reg = <0x20>; ++ status = "okay"; ++ }; ++ ++ // rtc clock ++ ds1307: ds1307@68 { ++ compatible = "dallas,ds1307"; ++ reg = <0x68>; ++ status = "okay"; ++ }; ++ ++ // RGB LEDs (>= v1.1.0) ++ pca9633: pca9633@62 { ++ compatible = "nxp,pca9633"; ++ reg = <0x62>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ red@0 { ++ label = "red"; ++ reg = <0>; ++ linux,default-trigger = "none"; ++ }; ++ green@1 { ++ label = "green"; ++ reg = <1>; ++ linux,default-trigger = "none"; ++ }; ++ blue@2 { ++ label = "blue"; ++ reg = <2>; ++ linux,default-trigger = "none"; ++ }; ++ unused@3 { ++ label = "unused"; ++ reg = <3>; ++ linux,default-trigger = "none"; ++ }; ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/cma-overlay.dts b/arch/arm/boot/dts/overlays/cma-overlay.dts +new file mode 100644 +index 000000000000..1d87c599f909 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/cma-overlay.dts +@@ -0,0 +1,36 @@ ++/* ++ * cma.dts ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&cma>; ++ frag0: __overlay__ { ++ /* ++ * The default size when using this overlay is 256 MB ++ * and should be kept as is for backwards ++ * compatibility. ++ */ ++ size = <0x10000000>; ++ }; ++ }; ++ ++ __overrides__ { ++ cma-512 = <&frag0>,"size:0=",<0x20000000>; ++ cma-448 = <&frag0>,"size:0=",<0x1c000000>; ++ cma-384 = <&frag0>,"size:0=",<0x18000000>; ++ cma-320 = <&frag0>,"size:0=",<0x14000000>; ++ cma-256 = <&frag0>,"size:0=",<0x10000000>; ++ cma-192 = <&frag0>,"size:0=",<0xC000000>; ++ cma-128 = <&frag0>,"size:0=",<0x8000000>; ++ cma-96 = <&frag0>,"size:0=",<0x6000000>; ++ cma-64 = <&frag0>,"size:0=",<0x4000000>; ++ cma-size = <&frag0>,"size:0"; /* in bytes, 4MB aligned */ ++ cma-default = <0>,"-0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/dht11-overlay.dts b/arch/arm/boot/dts/overlays/dht11-overlay.dts +new file mode 100644 +index 000000000000..6feeeb402493 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/dht11-overlay.dts +@@ -0,0 +1,41 @@ ++/* ++ * Overlay for the DHT11/21/22 humidity/temperature sensor modules. ++ */ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ ++ dht11: dht11@0 { ++ compatible = "dht11"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&dht11_pins>; ++ gpios = <&gpio 4 0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ dht11_pins: dht11_pins@0 { ++ brcm,pins = <4>; ++ brcm,function = <0>; // in ++ brcm,pull = <0>; // off ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpiopin = <&dht11_pins>,"brcm,pins:0", ++ <&dht11_pins>, "reg:0", ++ <&dht11>,"gpios:4", ++ <&dht11>,"reg:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/dionaudio-loco-overlay.dts b/arch/arm/boot/dts/overlays/dionaudio-loco-overlay.dts +new file mode 100644 +index 000000000000..d863e5c167cc +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/dionaudio-loco-overlay.dts +@@ -0,0 +1,39 @@ ++// Definitions for Dion Audio LOCO DAC-AMP ++ ++/* ++ * PCM5242 DAC (in hardware mode) and TPA3118 AMP. ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ pcm5102a-codec { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5102a"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "dionaudio,loco-pcm5242-tpa3118"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/dionaudio-loco-v2-overlay.dts b/arch/arm/boot/dts/overlays/dionaudio-loco-v2-overlay.dts +new file mode 100644 +index 000000000000..dfb8922a654b +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/dionaudio-loco-v2-overlay.dts +@@ -0,0 +1,49 @@ ++/* ++ * Definitions for Dion Audio LOCO-V2 DAC-AMP ++ * eg. dtoverlay=dionaudio-loco-v2 ++ * ++ * PCM5242 DAC (in software mode) and TPA3255 AMP. ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&sound>; ++ frag0: __overlay__ { ++ compatible = "dionaudio,dionaudio-loco-v2"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4c { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4d>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = <&frag0>,"dionaudio,24db_digital_gain?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/disable-bt-overlay.dts b/arch/arm/boot/dts/overlays/disable-bt-overlay.dts +new file mode 100644 +index 000000000000..d5a66e5d76a9 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/disable-bt-overlay.dts +@@ -0,0 +1,64 @@ ++/dts-v1/; ++/plugin/; ++ ++/* Disable Bluetooth and restore UART0/ttyAMA0 over GPIOs 14 & 15. ++ To disable the systemd service that initialises the modem so it doesn't use ++ the UART: ++ ++ sudo systemctl disable hciuart ++*/ ++ ++#include ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&uart1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&uart0>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&bt>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&uart0_pins>; ++ __overlay__ { ++ brcm,pins; ++ brcm,function; ++ brcm,pull; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&bt_pins>; ++ __overlay__ { ++ brcm,pins; ++ brcm,function; ++ brcm,pull; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path = "/aliases"; ++ __overlay__ { ++ serial0 = "/soc/serial@7e201000"; ++ serial1 = "/soc/serial@7e215040"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/disable-wifi-overlay.dts b/arch/arm/boot/dts/overlays/disable-wifi-overlay.dts +new file mode 100644 +index 000000000000..75e046463900 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/disable-wifi-overlay.dts +@@ -0,0 +1,20 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&mmc>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&mmcnr>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/dpi18-overlay.dts b/arch/arm/boot/dts/overlays/dpi18-overlay.dts +new file mode 100644 +index 000000000000..4abe5be744db +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/dpi18-overlay.dts +@@ -0,0 +1,39 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ // There is no DPI driver module, but we need a platform device ++ // node (that doesn't already use pinctrl) to hang the pinctrl ++ // reference on - leds will do ++ ++ fragment@0 { ++ target = <&fb>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&dpi18_pins>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&vc4>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&dpi18_pins>; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ dpi18_pins: dpi18_pins { ++ brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11 ++ 12 13 14 15 16 17 18 19 20 ++ 21>; ++ brcm,function = <6>; /* alt2 */ ++ brcm,pull = <0>; /* no pull */ ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/dpi24-overlay.dts b/arch/arm/boot/dts/overlays/dpi24-overlay.dts +new file mode 100644 +index 000000000000..44335cc81277 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/dpi24-overlay.dts +@@ -0,0 +1,39 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ // There is no DPI driver module, but we need a platform device ++ // node (that doesn't already use pinctrl) to hang the pinctrl ++ // reference on - leds will do ++ ++ fragment@0 { ++ target = <&fb>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&dpi24_pins>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&vc4>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&dpi24_pins>; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ dpi24_pins: dpi24_pins { ++ brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11 ++ 12 13 14 15 16 17 18 19 20 ++ 21 22 23 24 25 26 27>; ++ brcm,function = <6>; /* alt2 */ ++ brcm,pull = <0>; /* no pull */ ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/draws-overlay.dts b/arch/arm/boot/dts/overlays/draws-overlay.dts +new file mode 100644 +index 000000000000..d18187d7f343 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/draws-overlay.dts +@@ -0,0 +1,208 @@ ++#include ++/* ++ * Device tree overlay for the DRAWS Hardware ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ regulators { ++ compatible = "simple-bus"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ udrc0_ldoin: udrc0_ldoin { ++ compatible = "regulator-fixed"; ++ regulator-name = "ldoin"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ regulator-always-on; ++ }; ++ ++ sc16is752_clk: sc16is752_draws_clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <1843200>; ++ }; ++ }; ++ ++ pps: pps { ++ compatible = "pps-gpio"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pps_pins>; ++ gpios = <&gpio 7 0>; ++ status = "okay"; ++ }; ++ ++ iio-hwmon { ++ compatible = "iio-hwmon"; ++ status = "okay"; ++ io-channels = <&tla2024 4>, <&tla2024 5>, <&tla2024 6>, ++ <&tla2024 7>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ tlv320aic32x4: tlv320aic32x4@18 { ++ compatible = "ti,tlv320aic32x4"; ++ reg = <0x18>; ++ #sound-dai-cells = <0>; ++ status = "okay"; ++ ++ clocks = <&clocks BCM2835_CLOCK_GP0>; ++ clock-names = "mclk"; ++ assigned-clocks = <&clocks BCM2835_CLOCK_GP0>; ++ assigned-clock-rates = <25000000>; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&gpclk0_pin &aic3204_reset>; ++ ++ reset-gpios = <&gpio 13 0>; ++ ++ iov-supply = <&udrc0_ldoin>; ++ ldoin-supply = <&udrc0_ldoin>; ++ }; ++ ++ sc16is752: sc16is752@50 { ++ compatible = "nxp,sc16is752"; ++ reg = <0x50>; ++ clocks = <&sc16is752_clk>; ++ interrupt-parent = <&gpio>; ++ interrupts = <17 2>; /* IRQ_TYPE_EDGE_FALLING */ ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sc16is752_irq>; ++ }; ++ ++ tla2024: tla2024@48 { ++ compatible = "ti,ads1015"; ++ reg = <0x48>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ #io-channel-cells = <1>; ++ ++ adc_ch4: channel@4 { ++ reg = <4>; ++ ti,gain = <1>; ++ ti,datarate = <4>; ++ }; ++ ++ adc_ch5: channel@5 { ++ reg = <5>; ++ ti,gain = <1>; ++ ti,datarate = <4>; ++ }; ++ ++ adc_ch6: channel@6 { ++ reg = <6>; ++ ti,gain = <2>; ++ ti,datarate = <4>; ++ }; ++ ++ adc_ch7: channel@7 { ++ reg = <7>; ++ ti,gain = <2>; ++ ti,datarate = <4>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sound>; ++ snd: __overlay__ { ++ compatible = "simple-audio-card"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ ++ simple-audio-card,name = "draws"; ++ simple-audio-card,format = "i2s"; ++ ++ simple-audio-card,bitclock-master = <&dailink0_master>; ++ simple-audio-card,frame-master = <&dailink0_master>; ++ ++ simple-audio-card,widgets = ++ "Line", "Line In", ++ "Line", "Line Out"; ++ ++ simple-audio-card,routing = ++ "IN1_R", "Line In", ++ "IN1_L", "Line In", ++ "CM_L", "Line In", ++ "CM_R", "Line In", ++ "Line Out", "LOR", ++ "Line Out", "LOL"; ++ ++ dailink0_master: simple-audio-card,cpu { ++ sound-dai = <&i2s>; ++ }; ++ ++ simple-audio-card,codec { ++ sound-dai = <&tlv320aic32x4>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&gpio>; ++ __overlay__ { ++ gpclk0_pin: gpclk0_pin { ++ brcm,pins = <4>; ++ brcm,function = <4>; ++ }; ++ ++ aic3204_reset: aic3204_reset { ++ brcm,pins = <13>; ++ brcm,function = <1>; ++ brcm,pull = <1>; ++ }; ++ ++ aic3204_gpio: aic3204_gpio { ++ brcm,pins = <26>; ++ }; ++ ++ sc16is752_irq: sc16is752_irq { ++ brcm,pins = <17>; ++ brcm,function = <0>; ++ brcm,pull = <2>; ++ }; ++ ++ pps_pins: pps_pins { ++ brcm,pins = <7>; ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ draws_adc_ch4_gain = <&adc_ch4>,"ti,gain:0"; ++ draws_adc_ch4_datarate = <&adc_ch4>,"ti,datarate:0"; ++ draws_adc_ch5_gain = <&adc_ch5>,"ti,gain:0"; ++ draws_adc_ch5_datarate = <&adc_ch5>,"ti,datarate:0"; ++ draws_adc_ch6_gain = <&adc_ch6>,"ti,gain:0"; ++ draws_adc_ch6_datarate = <&adc_ch6>,"ti,datarate:0"; ++ draws_adc_ch7_gain = <&adc_ch7>,"ti,gain:0"; ++ draws_adc_ch7_datarate = <&adc_ch7>,"ti,datarate:0"; ++ alsaname = <&snd>, "simple-audio-card,name"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/dwc-otg-overlay.dts b/arch/arm/boot/dts/overlays/dwc-otg-overlay.dts +new file mode 100644 +index 000000000000..78c5e9f85048 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/dwc-otg-overlay.dts +@@ -0,0 +1,14 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&usb>; ++ __overlay__ { ++ compatible = "brcm,bcm2708-usb"; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/dwc2-overlay.dts b/arch/arm/boot/dts/overlays/dwc2-overlay.dts +new file mode 100644 +index 000000000000..0d83e344ad97 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/dwc2-overlay.dts +@@ -0,0 +1,26 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&usb>; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ dwc2_usb: __overlay__ { ++ compatible = "brcm,bcm2835-usb"; ++ dr_mode = "otg"; ++ g-np-tx-fifo-size = <32>; ++ g-rx-fifo-size = <558>; ++ g-tx-fifo-size = <512 512 512 512 512 256 256>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ dr_mode = <&dwc2_usb>, "dr_mode"; ++ g-np-tx-fifo-size = <&dwc2_usb>,"g-np-tx-fifo-size:0"; ++ g-rx-fifo-size = <&dwc2_usb>,"g-rx-fifo-size:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/enc28j60-overlay.dts b/arch/arm/boot/dts/overlays/enc28j60-overlay.dts +new file mode 100644 +index 000000000000..7af5c2e607ea +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/enc28j60-overlay.dts +@@ -0,0 +1,53 @@ ++// Overlay for the Microchip ENC28J60 Ethernet Controller ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ eth1: enc28j60@0{ ++ compatible = "microchip,enc28j60"; ++ reg = <0>; /* CE0 */ ++ pinctrl-names = "default"; ++ pinctrl-0 = <ð1_pins>; ++ interrupt-parent = <&gpio>; ++ interrupts = <25 0x2>; /* falling edge */ ++ spi-max-frequency = <12000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ eth1_pins: eth1_pins { ++ brcm,pins = <25>; ++ brcm,function = <0>; /* in */ ++ brcm,pull = <0>; /* none */ ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ int_pin = <ð1>, "interrupts:0", ++ <ð1_pins>, "brcm,pins:0"; ++ speed = <ð1>, "spi-max-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/enc28j60-spi2-overlay.dts b/arch/arm/boot/dts/overlays/enc28j60-spi2-overlay.dts +new file mode 100644 +index 000000000000..17cb5b8fa485 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/enc28j60-spi2-overlay.dts +@@ -0,0 +1,47 @@ ++// Overlay for the Microchip ENC28J60 Ethernet Controller - SPI2 Compute Module ++// Interrupt pin: 39 ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi2>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ eth1: enc28j60@0{ ++ compatible = "microchip,enc28j60"; ++ reg = <0>; /* CE0 */ ++ pinctrl-names = "default"; ++ pinctrl-0 = <ð1_pins>; ++ interrupt-parent = <&gpio>; ++ interrupts = <39 0x2>; /* falling edge */ ++ spi-max-frequency = <12000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ eth1_pins: eth1_pins { ++ brcm,pins = <39>; ++ brcm,function = <0>; /* in */ ++ brcm,pull = <0>; /* none */ ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ int_pin = <ð1>, "interrupts:0", ++ <ð1_pins>, "brcm,pins:0"; ++ speed = <ð1>, "spi-max-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/exc3000-overlay.dts b/arch/arm/boot/dts/overlays/exc3000-overlay.dts +new file mode 100644 +index 000000000000..6f087fb20661 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/exc3000-overlay.dts +@@ -0,0 +1,48 @@ ++// Device tree overlay for I2C connected EETI EXC3000 multiple touch controller ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ exc3000_pins: exc3000_pins { ++ brcm,pins = <4>; // interrupt ++ brcm,function = <0>; // in ++ brcm,pull = <2>; // pull-up ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ exc3000: exc3000@2a { ++ compatible = "eeti,exc3000"; ++ reg = <0x2a>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&exc3000_pins>; ++ interrupt-parent = <&gpio>; ++ interrupts = <4 8>; // active low level-sensitive ++ touchscreen-size-x = <4096>; ++ touchscreen-size-y = <4096>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ interrupt = <&exc3000_pins>,"brcm,pins:0", ++ <&exc3000>,"interrupts:0"; ++ sizex = <&exc3000>,"touchscreen-size-x:0"; ++ sizey = <&exc3000>,"touchscreen-size-y:0"; ++ invx = <&exc3000>,"touchscreen-inverted-x?"; ++ invy = <&exc3000>,"touchscreen-inverted-y?"; ++ swapxy = <&exc3000>,"touchscreen-swapped-x-y?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/fe-pi-audio-overlay.dts b/arch/arm/boot/dts/overlays/fe-pi-audio-overlay.dts +new file mode 100644 +index 000000000000..743f14ae5768 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/fe-pi-audio-overlay.dts +@@ -0,0 +1,70 @@ ++// Definitions for Fe-Pi Audio ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ sgtl5000_mclk: sgtl5000_mclk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <12288000>; ++ clock-output-names = "sgtl5000-mclk"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&soc>; ++ __overlay__ { ++ reg_1v8: reg_1v8@0 { ++ compatible = "regulator-fixed"; ++ regulator-name = "1V8"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ regulator-always-on; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ sgtl5000@0a { ++ #sound-dai-cells = <0>; ++ compatible = "fsl,sgtl5000"; ++ reg = <0x0a>; ++ clocks = <&sgtl5000_mclk>; ++ micbias-resistor-k-ohms = <2>; ++ micbias-voltage-m-volts = <3000>; ++ VDDA-supply = <&vdd_3v3_reg>; ++ VDDIO-supply = <&vdd_3v3_reg>; ++ VDDD-supply = <®_1v8>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "fe-pi,fe-pi-audio"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/fsm-demo-overlay.dts b/arch/arm/boot/dts/overlays/fsm-demo-overlay.dts +new file mode 100644 +index 000000000000..9e06e388e4d3 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/fsm-demo-overlay.dts +@@ -0,0 +1,104 @@ ++// Demo overlay for the gpio-fsm driver ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++#define BUTTON1 GF_IP(0) ++#define BUTTON2 GF_SW(0) ++#define RED GF_OP(0) // GPIO7 ++#define AMBER GF_OP(1) // GPIO8 ++#define GREEN GF_OP(2) // GPIO25 ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ fsm_demo: fsm-demo { ++ compatible = "rpi,gpio-fsm"; ++ ++ debug = <0>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ num-soft-gpios = <1>; ++ gpio-line-names = "button2"; ++ input-gpios = <&gpio 6 1>; // BUTTON1 (active-low) ++ output-gpios = <&gpio 7 0>, // RED ++ <&gpio 8 0>, // AMBER ++ <&gpio 25 0>; // GREEN ++ shutdown-timeout-ms = <2000>; ++ ++ start { ++ start_state; ++ set = , , ; ++ start2 = ; ++ }; ++ ++ start2 { ++ set = , ; ++ go = ; ++ }; ++ ++ go { ++ set = , , ; ++ ready_wait = ; ++ shutdown1 = ; ++ }; ++ ++ ready_wait { ++ // Clear the soft GPIO ++ set = ; ++ ready = ; ++ shutdown1 = ; ++ }; ++ ++ ready { ++ stopping = , ; ++ shutdown1 = ; ++ }; ++ ++ stopping { ++ set = , ; ++ stopped = ; ++ }; ++ ++ stopped { ++ set = , ; ++ get_set = ; ++ shutdown1 = ; ++ }; ++ ++ get_set { ++ set = ; ++ go = ; ++ }; ++ ++ shutdown1 { ++ set = , , ; ++ shutdown2 = ; ++ }; ++ ++ shutdown2 { ++ set = , ; ++ shutdown3 = ; ++ }; ++ ++ shutdown3 { ++ set = , ; ++ shutdown4 = ; ++ }; ++ ++ shutdown4 { ++ shutdown_state; ++ set = ; ++ }; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ fsm_debug = <&fsm_demo>,"debug:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/ghost-amp-overlay.dts b/arch/arm/boot/dts/overlays/ghost-amp-overlay.dts +new file mode 100644 +index 000000000000..afc9f034b5fc +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ghost-amp-overlay.dts +@@ -0,0 +1,119 @@ ++// Overlay for the PCM5122-based Ghost amplifier using gpio-fsm ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++#define ENABLE GF_SW(0) ++#define FAULT GF_IP(0) // GPIO5 ++#define RELAY1 GF_OP(0) // GPIO22 ++#define RELAY2 GF_OP(1) // GPIO23 ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4c { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4c>; ++ AVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ CPVDD-supply = <&vdd_3v3_reg>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ iqaudio_dac: __overlay__ { ++ compatible = "iqaudio,iqaudio-dac"; ++ i2s-controller = <&i2s>; ++ mute-gpios = <& 0 0>; ++ iqaudio-dac,auto-mute-amp; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path = "/"; ++ __overlay__ { ++ amp: ghost-amp { ++ compatible = "rpi,gpio-fsm"; ++ ++ debug = <0>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ num-soft-gpios = <1>; ++ gpio-line-names = "enable"; ++ input-gpios = <&gpio 5 1>; // FAULT (active low) ++ output-gpios = <&gpio 22 0>, // RELAY1 ++ <&gpio 23 0>; // RELAY2 ++ shutdown-timeout-ms = <1000>; ++ ++ amp_off { ++ start_state; ++ shutdown_state; ++ ++ set = , ++ ; ++ amp_on_1 = ; ++ fault = ; ++ }; ++ ++ amp_on_1 { ++ set = ; ++ amp_on = ; ++ amp_off = ; ++ fault = ; ++ }; ++ ++ amp_on { ++ set = ; ++ amp_off_wait = ; ++ fault = ; ++ }; ++ ++ amp_off_wait { ++ amp_off_1 = , ++ ; ++ amp_on = ; ++ fault = ; ++ }; ++ ++ amp_off_1 { ++ set = ; ++ amp_on = ; ++ amp_off = ; ++ fault = ; ++ }; ++ ++ // Keep this a distinct state to prevent ++ // changes and for the diagnostic output ++ fault { ++ set = , ++ ; ++ shutdown_state; ++ }; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ fsm_debug = <&>,"debug:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/goodix-overlay.dts b/arch/arm/boot/dts/overlays/goodix-overlay.dts +new file mode 100644 +index 000000000000..a11d65f81c5e +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/goodix-overlay.dts +@@ -0,0 +1,46 @@ ++// Device tree overlay for I2C connected Goodix gt9271 multiple touch controller ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ goodix_pins: goodix_pins { ++ brcm,pins = <4 17>; // interrupt and reset ++ brcm,function = <0 0>; // in ++ brcm,pull = <2 2>; // pull-up ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ gt9271: gt9271@14 { ++ compatible = "goodix,gt9271"; ++ reg = <0x14>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&goodix_pins>; ++ interrupt-parent = <&gpio>; ++ interrupts = <4 2>; // high-to-low edge triggered ++ irq-gpios = <&gpio 4 0>; // Pin7 on GPIO header ++ reset-gpios = <&gpio 17 1>; // Pin11 on GPIO header ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ interrupt = <&goodix_pins>,"brcm,pins:0", ++ <>9271>,"interrupts:0", ++ <>9271>,"irq-gpios:4"; ++ reset = <&goodix_pins>,"brcm,pins:4", ++ <>9271>,"reset-gpios:4"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/googlevoicehat-soundcard-overlay.dts b/arch/arm/boot/dts/overlays/googlevoicehat-soundcard-overlay.dts +new file mode 100644 +index 000000000000..e443be1f9a0e +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/googlevoicehat-soundcard-overlay.dts +@@ -0,0 +1,49 @@ ++// Definitions for Google voiceHAT v1 soundcard overlay ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ googlevoicehat_pins: googlevoicehat_pins { ++ brcm,pins = <16>; ++ brcm,function = <1>; /* out */ ++ brcm,pull = <0>; /* up */ ++ }; ++ }; ++ }; ++ ++ ++ fragment@2 { ++ target-path = "/"; ++ __overlay__ { ++ voicehat-codec { ++ #sound-dai-cells = <0>; ++ compatible = "google,voicehat"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&googlevoicehat_pins>; ++ sdmode-gpios= <&gpio 16 0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "googlevoicehat,googlevoicehat-soundcard"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/gpio-fan-overlay.dts b/arch/arm/boot/dts/overlays/gpio-fan-overlay.dts +new file mode 100644 +index 000000000000..77a7bbb41e3b +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/gpio-fan-overlay.dts +@@ -0,0 +1,79 @@ ++/* ++ * Overlay for the Raspberry Pi GPIO Fan @ BCM GPIO12. ++ * References: ++ * - https://www.raspberrypi.org/forums/viewtopic.php?f=107&p=1367135#p1365084 ++ * ++ * Optional parameters: ++ * - "gpiopin" - BCM number of the pin driving the fan, default 12 (GPIO12); ++ * - "temp" - CPU temperature at which fan is started in millicelsius, default 55000; ++ * ++ * Requires: ++ * - kernel configurations: CONFIG_SENSORS_GPIO_FAN=m; ++ * - kernel rebuild; ++ * - N-MOSFET connected to gpiopin, 2N7002-[https://en.wikipedia.org/wiki/2N7000]; ++ * - DC Fan connected to N-MOSFET Drain terminal, a 12V fan is working fine and quite silently; ++ * [https://www.tme.eu/en/details/ee40101s1-999-a/dc12v-fans/sunon/ee40101s1-1000u-999/] ++ * ++ * ┌─────────────────────┐ ++ * │Fan negative terminal│ ++ * └┬────────────────────┘ ++ * │D ++ * G │──┘ ++ * [GPIO12]──────┤ │<─┐ 2N7002 ++ * │──┤ ++ * │S ++ * ─┴─ ++ * GND ++ * ++ * Build: ++ * - `sudo dtc -W no-unit_address_vs_reg -@ -I dts -O dtb -o /boot/overlays/gpio-fan.dtbo gpio-fan-overlay.dts` ++ * Activate: ++ * - sudo nano /boot/config.txt add "dtoverlay=gpio-fan" or "dtoverlay=gpio-fan,gpiopin=12,temp=45000" ++ * or ++ * - sudo sh -c 'printf "\n# Enable PI GPIO-Fan Default\ndtoverlay=gpio-fan\n" >> /boot/config.txt' ++ * - sudo sh -c 'printf "\n# Enable PI GPIO-Fan Custom\ndtoverlay=gpio-fan,gpiopin=12,temp=45000\n" >> /boot/config.txt' ++ * ++ */ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ fan0: gpio-fan@0 { ++ compatible = "gpio-fan"; ++ gpios = <&gpio 12 0>; ++ gpio-fan,speed-map = <0 0>, ++ <5000 1>; ++ #cooling-cells = <2>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&cpu_thermal>; ++ polling-delay = <2000>; /* milliseconds */ ++ __overlay__ { ++ trips { ++ cpu_hot: trip-point@0 { ++ temperature = <55000>; /* (millicelsius) Fan started at 55°C */ ++ hysteresis = <10000>; /* (millicelsius) Fan stopped at 45°C */ ++ type = "active"; ++ }; ++ }; ++ cooling-maps { ++ map0 { ++ trip = <&cpu_hot>; ++ cooling-device = <&fan0 1 1>; ++ }; ++ }; ++ }; ++ }; ++ __overrides__ { ++ gpiopin = <&fan0>,"gpios:4", <&fan0>,"brcm,pins:0"; ++ temp = <&cpu_hot>,"temperature:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/gpio-ir-overlay.dts b/arch/arm/boot/dts/overlays/gpio-ir-overlay.dts +new file mode 100644 +index 000000000000..162b6ce07dc9 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/gpio-ir-overlay.dts +@@ -0,0 +1,49 @@ ++// Definitions for ir-gpio module ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ gpio_ir: ir-receiver@12 { ++ compatible = "gpio-ir-receiver"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&gpio_ir_pins>; ++ ++ // pin number, high or low ++ gpios = <&gpio 18 1>; ++ ++ // parameter for keymap name ++ linux,rc-map-name = "rc-rc6-mce"; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ gpio_ir_pins: gpio_ir_pins@12 { ++ brcm,pins = <18>; // pin 18 ++ brcm,function = <0>; // in ++ brcm,pull = <2>; // up ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ // parameters ++ gpio_pin = <&gpio_ir>,"gpios:4", // pin number ++ <&gpio_ir>,"reg:0", ++ <&gpio_ir_pins>,"brcm,pins:0", ++ <&gpio_ir_pins>,"reg:0"; ++ gpio_pull = <&gpio_ir_pins>,"brcm,pull:0"; // pull-up/down state ++ invert = <&gpio_ir>,"gpios:8"; // 0 = active high input ++ ++ rc-map-name = <&gpio_ir>,"linux,rc-map-name"; // default rc map ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/gpio-ir-tx-overlay.dts b/arch/arm/boot/dts/overlays/gpio-ir-tx-overlay.dts +new file mode 100644 +index 000000000000..3625431b7560 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/gpio-ir-tx-overlay.dts +@@ -0,0 +1,36 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ gpio_ir_tx_pins: gpio_ir_tx_pins@12 { ++ brcm,pins = <18>; ++ brcm,function = <1>; // out ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ gpio_ir_tx: gpio-ir-transmitter@12 { ++ compatible = "gpio-ir-tx"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&gpio_ir_tx_pins>; ++ gpios = <&gpio 18 0>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpio_pin = <&gpio_ir_tx>, "gpios:4", // pin number ++ <&gpio_ir_tx>, "reg:0", ++ <&gpio_ir_tx_pins>, "brcm,pins:0", ++ <&gpio_ir_tx_pins>, "reg:0"; ++ invert = <&gpio_ir_tx>, "gpios:8"; // 1 = active low ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/gpio-key-overlay.dts b/arch/arm/boot/dts/overlays/gpio-key-overlay.dts +new file mode 100644 +index 000000000000..2e7253d1d0ab +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/gpio-key-overlay.dts +@@ -0,0 +1,48 @@ ++// Definitions for gpio-key module ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ // Configure the gpio pin controller ++ target = <&gpio>; ++ __overlay__ { ++ pin_state: button_pins@0 { ++ brcm,pins = <3>; // gpio number ++ brcm,function = <0>; // 0 = input, 1 = output ++ brcm,pull = <2>; // 0 = none, 1 = pull down, 2 = pull up ++ }; ++ }; ++ }; ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ button: button@0 { ++ compatible = "gpio-keys"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pin_state>; ++ status = "okay"; ++ ++ key: key { ++ linux,code = <116>; ++ gpios = <&gpio 3 1>; ++ label = "KEY_POWER"; ++ }; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpio = <&key>,"gpios:4", ++ <&button>,"reg:0", ++ <&pin_state>,"brcm,pins:0", ++ <&pin_state>,"reg:0"; ++ label = <&key>,"label"; ++ keycode = <&key>,"linux,code:0"; ++ gpio_pull = <&pin_state>,"brcm,pull:0"; ++ active_low = <&key>,"gpios:8"; ++ }; ++ ++}; +diff --git a/arch/arm/boot/dts/overlays/gpio-no-bank0-irq-overlay.dts b/arch/arm/boot/dts/overlays/gpio-no-bank0-irq-overlay.dts +new file mode 100755 +index 000000000000..96cbe80820b7 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/gpio-no-bank0-irq-overlay.dts +@@ -0,0 +1,14 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ // Configure the gpio pin controller ++ target = <&gpio>; ++ __overlay__ { ++ interrupts = <255 255>, <2 18>; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/gpio-no-irq-overlay.dts b/arch/arm/boot/dts/overlays/gpio-no-irq-overlay.dts +new file mode 100644 +index 000000000000..55f9bff3a8f6 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/gpio-no-irq-overlay.dts +@@ -0,0 +1,14 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ // Configure the gpio pin controller ++ target = <&gpio>; ++ __overlay__ { ++ interrupts; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/gpio-poweroff-overlay.dts b/arch/arm/boot/dts/overlays/gpio-poweroff-overlay.dts +new file mode 100644 +index 000000000000..416aa2bc797a +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/gpio-poweroff-overlay.dts +@@ -0,0 +1,37 @@ ++// Definitions for gpio-poweroff module ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ power_ctrl: power_ctrl { ++ compatible = "gpio-poweroff"; ++ gpios = <&gpio 26 0>; ++ force; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ power_ctrl_pins: power_ctrl_pins { ++ brcm,pins = <26>; ++ brcm,function = <1>; // out ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpiopin = <&power_ctrl>,"gpios:4", ++ <&power_ctrl_pins>,"brcm,pins:0"; ++ active_low = <&power_ctrl>,"gpios:8"; ++ input = <&power_ctrl>,"input?"; ++ export = <&power_ctrl>,"export?"; ++ timeout_ms = <&power_ctrl>,"timeout-ms:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/gpio-shutdown-overlay.dts b/arch/arm/boot/dts/overlays/gpio-shutdown-overlay.dts +new file mode 100644 +index 000000000000..0a27595143ec +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/gpio-shutdown-overlay.dts +@@ -0,0 +1,84 @@ ++// Definitions for gpio-poweroff module ++/dts-v1/; ++/plugin/; ++ ++// This overlay sets up an input device that generates KEY_POWER events ++// when a given GPIO pin changes. It defaults to using GPIO3, which can ++// also be used to wake up (start) the Rpi again after shutdown. ++// Raspberry Pi 1 Model B rev 1 can be wake up only by GPIO1 pin, so for ++// these boards change default GPIO pin to 1 via gpio_pin parameter. Since ++// wakeup is active-low, this defaults to active-low with a pullup ++// enabled, but all of this can be changed using overlay parameters (but ++// note that GPIO3 has an external pullup on at least some boards). ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ // Configure the gpio pin controller ++ target = <&gpio>; ++ __overlay__ { ++ // Define a pinctrl state, that sets up the gpio ++ // as an input with a pullup enabled. This does ++ // not take effect by itself, only when referenced ++ // by a "pinctrl client", as is done below. See: ++ // https://www.kernel.org/doc/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt ++ // https://www.kernel.org/doc/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt ++ pin_state: shutdown_button_pins { ++ brcm,pins = <3>; // gpio number ++ brcm,function = <0>; // 0 = input, 1 = output ++ brcm,pull = <2>; // 0 = none, 1 = pull down, 2 = pull up ++ }; ++ }; ++ }; ++ fragment@1 { ++ // Add a new device to the /soc devicetree node ++ target-path = "/soc"; ++ __overlay__ { ++ shutdown_button { ++ // Let the gpio-keys driver handle this device. See: ++ // https://www.kernel.org/doc/Documentation/devicetree/bindings/input/gpio-keys.txt ++ compatible = "gpio-keys"; ++ ++ // Declare a single pinctrl state (referencing the one declared above) and name it ++ // default, so it is activated automatically. ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pin_state>; ++ ++ // Enable this device ++ status = "okay"; ++ ++ // Define a single key, called "shutdown" that monitors the gpio and sends KEY_POWER ++ // (keycode 116, see ++ // https://github.com/torvalds/linux/blob/v4.12/include/uapi/linux/input-event-codes.h#L190) ++ button: shutdown { ++ label = "shutdown"; ++ linux,code = <116>; // KEY_POWER ++ gpios = <&gpio 3 1>; ++ debounce-interval = <100>; // ms ++ }; ++ }; ++ }; ++ }; ++ ++ // This defines parameters that can be specified when loading ++ // the overlay. Each foo = line specifies one parameter, named ++ // foo. The rest of the specification gives properties where the ++ // parameter value is inserted into (changing the values above ++ // or adding new ones). ++ __overrides__ { ++ // Allow overriding the GPIO number. ++ gpio_pin = <&button>,"gpios:4", ++ <&pin_state>,"brcm,pins:0"; ++ ++ // Allow changing the internal pullup/down state. 0 = none, 1 = pulldown, 2 = pullup ++ // Note that GPIO3 and GPIO2 are the I2c pins and have an external pullup (at least ++ // on some boards). Same applies for GPIO1 on Raspberry Pi 1 Model B rev 1. ++ gpio_pull = <&pin_state>,"brcm,pull:0"; ++ ++ // Allow setting the active_low flag. 0 = active high, 1 = active low ++ active_low = <&button>,"gpios:8"; ++ debounce = <&button>,"debounce-interval:0"; ++ }; ++ ++}; +diff --git a/arch/arm/boot/dts/overlays/hd44780-lcd-overlay.dts b/arch/arm/boot/dts/overlays/hd44780-lcd-overlay.dts +new file mode 100644 +index 000000000000..ee726669ff51 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hd44780-lcd-overlay.dts +@@ -0,0 +1,46 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ lcd_screen: auxdisplay { ++ compatible = "hit,hd44780"; ++ ++ data-gpios = <&gpio 6 0>, ++ <&gpio 13 0>, ++ <&gpio 19 0>, ++ <&gpio 26 0>; ++ enable-gpios = <&gpio 21 0>; ++ rs-gpios = <&gpio 20 0>; ++ ++ display-height-chars = <2>; ++ display-width-chars = <16>; ++ }; ++ ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&lcd_screen>; ++ __dormant__ { ++ backlight-gpios = <&gpio 12 0>; ++ }; ++ }; ++ ++ __overrides__ { ++ pin_d4 = <&lcd_screen>,"data-gpios:4"; ++ pin_d5 = <&lcd_screen>,"data-gpios:16"; ++ pin_d6 = <&lcd_screen>,"data-gpios:28"; ++ pin_d7 = <&lcd_screen>,"data-gpios:40"; ++ pin_en = <&lcd_screen>,"enable-gpios:4"; ++ pin_rs = <&lcd_screen>,"rs-gpios:4"; ++ pin_bl = <0>,"+1", <&lcd_screen>,"backlight-gpios:4"; ++ display_height = <&lcd_screen>,"display-height-chars:0"; ++ display_width = <&lcd_screen>,"display-width-chars:0"; ++ }; ++ ++}; +diff --git a/arch/arm/boot/dts/overlays/hdmi-backlight-hwhack-gpio-overlay.dts b/arch/arm/boot/dts/overlays/hdmi-backlight-hwhack-gpio-overlay.dts +new file mode 100644 +index 000000000000..50b9a2665c80 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hdmi-backlight-hwhack-gpio-overlay.dts +@@ -0,0 +1,47 @@ ++/* ++ * Devicetree overlay for GPIO based backlight on/off capability. ++ * ++ * Use this if you have one of those HDMI displays whose backlight cannot be ++ * controlled via DPMS over HDMI and plan to do a little soldering to use an ++ * RPi gpio pin for on/off switching. ++ * ++ * See: https://www.waveshare.com/wiki/7inch_HDMI_LCD_(C)#Backlight_Control ++ * ++ */ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ hdmi_backlight_hwhack_gpio_pins: hdmi_backlight_hwhack_gpio_pins { ++ brcm,pins = <17>; ++ brcm,function = <1>; /* out */ ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "/"; ++ __overlay__ { ++ hdmi_backlight_hwhack_gpio: hdmi_backlight_hwhack_gpio { ++ compatible = "gpio-backlight"; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&hdmi_backlight_hwhack_gpio_pins>; ++ ++ gpios = <&gpio 17 0>; ++ default-on; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpio_pin = <&hdmi_backlight_hwhack_gpio>,"gpios:4", ++ <&hdmi_backlight_hwhack_gpio_pins>,"brcm,pins:0"; ++ active_low = <&hdmi_backlight_hwhack_gpio>,"gpios:8"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts b/arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts +new file mode 100644 +index 000000000000..142518ab348b +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-amp-overlay.dts +@@ -0,0 +1,39 @@ ++// Definitions for HiFiBerry Amp/Amp+ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ tas5713@1b { ++ #sound-dai-cells = <0>; ++ compatible = "ti,tas5713"; ++ reg = <0x1b>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "hifiberry,hifiberry-amp"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts b/arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts +new file mode 100644 +index 000000000000..ea8a6c8f36c0 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-dac-overlay.dts +@@ -0,0 +1,34 @@ ++// Definitions for HiFiBerry DAC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ pcm5102a-codec { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5102a"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "hifiberry,hifiberry-dac"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts b/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts +new file mode 100644 +index 000000000000..ff19015ba656 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-dacplus-overlay.dts +@@ -0,0 +1,65 @@ ++// Definitions for HiFiBerry DAC+ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ dacpro_osc: dacpro_osc { ++ compatible = "hifiberry,dacpro-clk"; ++ #clock-cells = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4d { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4d>; ++ clocks = <&dacpro_osc>; ++ AVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ CPVDD-supply = <&vdd_3v3_reg>; ++ status = "okay"; ++ }; ++ hpamp: hpamp@60 { ++ compatible = "ti,tpa6130a2"; ++ reg = <0x60>; ++ status = "disabled"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sound>; ++ hifiberry_dacplus: __overlay__ { ++ compatible = "hifiberry,hifiberry-dacplus"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = ++ <&hifiberry_dacplus>,"hifiberry,24db_digital_gain?"; ++ slave = <&hifiberry_dacplus>,"hifiberry-dacplus,slave?"; ++ leds_off = <&hifiberry_dacplus>,"hifiberry-dacplus,leds_off?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/hifiberry-dacplusadc-overlay.dts b/arch/arm/boot/dts/overlays/hifiberry-dacplusadc-overlay.dts +new file mode 100644 +index 000000000000..540563dec10f +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-dacplusadc-overlay.dts +@@ -0,0 +1,72 @@ ++// Definitions for HiFiBerry DAC+ADC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ dacpro_osc: dacpro_osc { ++ compatible = "hifiberry,dacpro-clk"; ++ #clock-cells = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm_codec: pcm5122@4d { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4d>; ++ clocks = <&dacpro_osc>; ++ AVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ CPVDD-supply = <&vdd_3v3_reg>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path = "/"; ++ __overlay__ { ++ dmic { ++ #sound-dai-cells = <0>; ++ compatible = "dmic-codec"; ++ num-channels = <2>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&sound>; ++ hifiberry_dacplusadc: __overlay__ { ++ compatible = "hifiberry,hifiberry-dacplusadc"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = ++ <&hifiberry_dacplusadc>,"hifiberry,24db_digital_gain?"; ++ slave = <&hifiberry_dacplusadc>,"hifiberry-dacplusadc,slave?"; ++ leds_off = <&hifiberry_dacplusadc>,"hifiberry-dacplusadc,leds_off?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/hifiberry-dacplusadcpro-overlay.dts b/arch/arm/boot/dts/overlays/hifiberry-dacplusadcpro-overlay.dts +new file mode 100644 +index 000000000000..cafa2ccd7ff7 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-dacplusadcpro-overlay.dts +@@ -0,0 +1,65 @@ ++// Definitions for HiFiBerry DAC+ADC PRO ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ dacpro_osc: dacpro_osc { ++ compatible = "hifiberry,dacpro-clk"; ++ #clock-cells = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ hb_dac: pcm5122@4d { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4d>; ++ clocks = <&dacpro_osc>; ++ status = "okay"; ++ }; ++ hb_adc: pcm186x@4a { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm1863"; ++ reg = <0x4a>; ++ clocks = <&dacpro_osc>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sound>; ++ hifiberry_dacplusadcpro: __overlay__ { ++ compatible = "hifiberry,hifiberry-dacplusadcpro"; ++ audio-codec = <&hb_dac &hb_adc>; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = ++ <&hifiberry_dacplusadcpro>,"hifiberry-dacplusadcpro,24db_digital_gain?"; ++ slave = <&hifiberry_dacplusadcpro>,"hifiberry-dacplusadcpro,slave?"; ++ leds_off = <&hifiberry_dacplusadcpro>,"hifiberry-dacplusadcpro,leds_off?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/hifiberry-dacplusdsp-overlay.dts b/arch/arm/boot/dts/overlays/hifiberry-dacplusdsp-overlay.dts +new file mode 100644 +index 000000000000..63432e8b983f +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-dacplusdsp-overlay.dts +@@ -0,0 +1,34 @@ ++// Definitions for hifiberry DAC+DSP soundcard overlay ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ dacplusdsp-codec { ++ #sound-dai-cells = <0>; ++ compatible = "hifiberry,dacplusdsp"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "hifiberrydacplusdsp,hifiberrydacplusdsp-soundcard"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/hifiberry-dacplushd-overlay.dts b/arch/arm/boot/dts/overlays/hifiberry-dacplushd-overlay.dts +new file mode 100644 +index 000000000000..c5583e010339 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-dacplushd-overlay.dts +@@ -0,0 +1,106 @@ ++// Definitions for HiFiBerry DAC+ HD ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ dachd_osc: pll_dachd_osc { ++ compatible = "hifiberry,dachd-clk"; ++ #clock-cells = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm1792a@4c { ++ compatible = "ti,pcm1792a"; ++ #sound-dai-cells = <0>; ++ #clock-cells = <0>; ++ clocks = <&dachd_osc>; ++ reg = <0x4c>; ++ status = "okay"; ++ }; ++ pll: pll@62 { ++ compatible = "hifiberry,dachd-clk"; ++ #clock-cells = <0>; ++ reg = <0x62>; ++ clocks = <&dachd_osc>; ++ status = "okay"; ++ common_pll_regs = [ ++ 02 53 03 00 07 20 0F 00 ++ 10 0D 11 1D 12 0D 13 8C ++ 14 8C 15 8C 16 8C 17 8C ++ 18 2A 1C 00 1D 0F 1F 00 ++ 2A 00 2C 00 2F 00 30 00 ++ 31 00 32 00 34 00 37 00 ++ 38 00 39 00 3A 00 3B 01 ++ 3E 00 3F 00 40 00 41 00 ++ 5A 00 5B 00 95 00 96 00 ++ 97 00 98 00 99 00 9A 00 ++ 9B 00 A2 00 A3 00 A4 00 ++ B7 92 ]; ++ 192k_pll_regs = [ ++ 1A 0C 1B 35 1E F0 20 09 ++ 21 50 2B 02 2D 10 2E 40 ++ 33 01 35 22 36 80 3C 22 ++ 3D 46 ]; ++ 96k_pll_regs = [ ++ 1A 0C 1B 35 1E F0 20 09 ++ 21 50 2B 02 2D 10 2E 40 ++ 33 01 35 47 36 00 3C 32 ++ 3D 46 ]; ++ 48k_pll_regs = [ ++ 1A 0C 1B 35 1E F0 20 09 ++ 21 50 2B 02 2D 10 2E 40 ++ 33 01 35 90 36 00 3C 42 ++ 3D 46 ]; ++ 176k4_pll_regs = [ ++ 1A 3D 1B 09 1E F3 20 13 ++ 21 75 2B 04 2D 11 2E E0 ++ 33 02 35 25 36 C0 3C 22 ++ 3D 7A ]; ++ 88k2_pll_regs = [ ++ 1A 3D 1B 09 1E F3 20 13 ++ 21 75 2B 04 2D 11 2E E0 ++ 33 01 35 4D 36 80 3C 32 ++ 3D 7A ]; ++ 44k1_pll_regs = [ ++ 1A 3D 1B 09 1E F3 20 13 ++ 21 75 2B 04 2D 11 2E E0 ++ 33 01 35 9D 36 00 3C 42 ++ 3D 7A ]; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "hifiberry,hifiberry-dacplushd"; ++ i2s-controller = <&i2s>; ++ clocks = <&pll 0>; ++ reset-gpio = <&gpio 16 GPIO_ACTIVE_LOW>; ++ status = "okay"; ++ }; ++ }; ++ ++}; +diff --git a/arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts b/arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts +new file mode 100644 +index 000000000000..a2309a50e8d8 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-digi-overlay.dts +@@ -0,0 +1,41 @@ ++// Definitions for HiFiBerry Digi ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8804@3b { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8804"; ++ reg = <0x3b>; ++ PVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "hifiberry,hifiberry-digi"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/hifiberry-digi-pro-overlay.dts b/arch/arm/boot/dts/overlays/hifiberry-digi-pro-overlay.dts +new file mode 100644 +index 000000000000..83de602e76ba +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hifiberry-digi-pro-overlay.dts +@@ -0,0 +1,43 @@ ++// Definitions for HiFiBerry Digi Pro ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8804@3b { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8804"; ++ reg = <0x3b>; ++ PVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "hifiberry,hifiberry-digi"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ clock44-gpio = <&gpio 5 0>; ++ clock48-gpio = <&gpio 6 0>; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/highperi-overlay.dts b/arch/arm/boot/dts/overlays/highperi-overlay.dts +new file mode 100644 +index 000000000000..46cb76c2d34f +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/highperi-overlay.dts +@@ -0,0 +1,63 @@ ++/* ++ * highperi.dts ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&soc>; ++ #address-cells = <2>; ++ #size-cells = <1>; ++ ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ ranges = <0x7c000000 0x4 0x7c000000 0x04000000>, ++ <0x40000000 0x4 0xc0000000 0x00800000>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&scb>; ++ #address-cells = <2>; ++ #size-cells = <1>; ++ ++ __overlay__ { ++ #address-cells = <2>; ++ #size-cells = <2>; ++ ranges = <0x0 0x7c000000 0x4 0x7c000000 0x0 0x04000000>, ++ <0x0 0x40000000 0x4 0xc0000000 0x0 0x00800000>, ++ <0x6 0x00000000 0x6 0x00000000 0x0 0x40000000>; ++ dma-ranges = <0x0 0x00000000 0x0 0x00000000 0x2 0x00000000>; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&v3dbus>; ++ #address-cells = <2>; ++ #size-cells = <1>; ++ ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <2>; ++ ranges = <0x7c500000 0x4 0x7c500000 0x0 0x03300000>, ++ <0x40000000 0x4 0xc0000000 0x0 0x00800000>; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&emmc2bus>; ++ #address-cells = <2>; ++ #size-cells = <1>; ++ ++ __overlay__ { ++ #address-cells = <2>; ++ #size-cells = <1>; ++ ranges = <0x0 0x7e000000 0x4 0x7e000000 0x01800000>; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/hy28a-overlay.dts b/arch/arm/boot/dts/overlays/hy28a-overlay.dts +new file mode 100644 +index 000000000000..5843a5e9c86a +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hy28a-overlay.dts +@@ -0,0 +1,93 @@ ++/* ++ * Device Tree overlay for HY28A display ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ hy28a_pins: hy28a_pins { ++ brcm,pins = <17 25 18>; ++ brcm,function = <0 1 1>; /* in out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ hy28a: hy28a@0{ ++ compatible = "ilitek,ili9320"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&hy28a_pins>; ++ ++ spi-max-frequency = <32000000>; ++ spi-cpol; ++ spi-cpha; ++ rotate = <270>; ++ bgr; ++ fps = <50>; ++ buswidth = <8>; ++ startbyte = <0x70>; ++ reset-gpios = <&gpio 25 1>; ++ led-gpios = <&gpio 18 1>; ++ debug = <0>; ++ }; ++ ++ hy28a_ts: hy28a-ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <17 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 17 0>; ++ ti,x-plate-ohms = /bits/ 16 <100>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ speed = <&hy28a>,"spi-max-frequency:0"; ++ rotate = <&hy28a>,"rotate:0"; ++ fps = <&hy28a>,"fps:0"; ++ debug = <&hy28a>,"debug:0"; ++ xohms = <&hy28a_ts>,"ti,x-plate-ohms;0"; ++ resetgpio = <&hy28a>,"reset-gpios:4", ++ <&hy28a_pins>, "brcm,pins:4"; ++ ledgpio = <&hy28a>,"led-gpios:4", ++ <&hy28a_pins>, "brcm,pins:8"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/hy28b-2017-overlay.dts b/arch/arm/boot/dts/overlays/hy28b-2017-overlay.dts +new file mode 100644 +index 000000000000..95bfb1eadc20 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hy28b-2017-overlay.dts +@@ -0,0 +1,152 @@ ++/* ++ * Device Tree overlay for HY28b display shield by Texy. ++ * Modified for 2017 version with ILI9325 D chip ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ hy28b_pins: hy28b_pins { ++ brcm,pins = <17 25 18>; ++ brcm,function = <0 1 1>; /* in out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ hy28b: hy28b@0{ ++ compatible = "ilitek,ili9325"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&hy28b_pins>; ++ ++ spi-max-frequency = <48000000>; ++ spi-cpol; ++ spi-cpha; ++ rotate = <270>; ++ bgr; ++ fps = <50>; ++ buswidth = <8>; ++ startbyte = <0x70>; ++ reset-gpios = <&gpio 25 1>; ++ led-gpios = <&gpio 18 1>; ++ ++ init = <0x10000e5 0x78F0 ++ 0x1000001 0x0100 ++ 0x1000002 0x0700 ++ 0x1000003 0x1030 ++ 0x1000004 0x0000 ++ 0x1000008 0x0207 ++ 0x1000009 0x0000 ++ 0x100000a 0x0000 ++ 0x100000c 0x0000 ++ 0x100000d 0x0000 ++ 0x100000f 0x0000 ++ 0x1000010 0x0000 ++ 0x1000011 0x0007 ++ 0x1000012 0x0000 ++ 0x1000013 0x0000 ++ 0x1000007 0x0001 ++ 0x2000032 ++ 0x2000032 ++ 0x2000032 ++ 0x2000032 ++ 0x1000010 0x1090 ++ 0x1000011 0x0227 ++ 0x2000032 ++ 0x1000012 0x001f ++ 0x2000032 ++ 0x1000013 0x1500 ++ 0x1000029 0x0027 ++ 0x100002b 0x000d ++ 0x2000032 ++ 0x1000020 0x0000 ++ 0x1000021 0x0000 ++ 0x2000032 ++ 0x1000030 0x0000 ++ 0x1000031 0x0707 ++ 0x1000032 0x0307 ++ 0x1000035 0x0200 ++ 0x1000036 0x0008 ++ 0x1000037 0x0004 ++ 0x1000038 0x0000 ++ 0x1000039 0x0707 ++ 0x100003c 0x0002 ++ 0x100003d 0x1d04 ++ 0x1000050 0x0000 ++ 0x1000051 0x00ef ++ 0x1000052 0x0000 ++ 0x1000053 0x013f ++ 0x1000060 0xa700 ++ 0x1000061 0x0001 ++ 0x100006a 0x0000 ++ 0x1000080 0x0000 ++ 0x1000081 0x0000 ++ 0x1000082 0x0000 ++ 0x1000083 0x0000 ++ 0x1000084 0x0000 ++ 0x1000085 0x0000 ++ 0x1000090 0x0010 ++ 0x1000092 0x0600 ++ 0x1000007 0x0133>; ++ debug = <0>; ++ }; ++ ++ hy28b_ts: hy28b-ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <17 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 17 0>; ++ ti,x-plate-ohms = /bits/ 16 <100>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ speed = <&hy28b>,"spi-max-frequency:0"; ++ rotate = <&hy28b>,"rotate:0"; ++ fps = <&hy28b>,"fps:0"; ++ debug = <&hy28b>,"debug:0"; ++ xohms = <&hy28b_ts>,"ti,x-plate-ohms;0"; ++ resetgpio = <&hy28b>,"reset-gpios:4", ++ <&hy28b_pins>, "brcm,pins:4"; ++ ledgpio = <&hy28b>,"led-gpios:4", ++ <&hy28b_pins>, "brcm,pins:8"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/hy28b-overlay.dts b/arch/arm/boot/dts/overlays/hy28b-overlay.dts +new file mode 100644 +index 000000000000..9edd0848d555 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/hy28b-overlay.dts +@@ -0,0 +1,148 @@ ++/* ++ * Device Tree overlay for HY28b display shield by Texy ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ hy28b_pins: hy28b_pins { ++ brcm,pins = <17 25 18>; ++ brcm,function = <0 1 1>; /* in out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ hy28b: hy28b@0{ ++ compatible = "ilitek,ili9325"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&hy28b_pins>; ++ ++ spi-max-frequency = <48000000>; ++ spi-cpol; ++ spi-cpha; ++ rotate = <270>; ++ bgr; ++ fps = <50>; ++ buswidth = <8>; ++ startbyte = <0x70>; ++ reset-gpios = <&gpio 25 1>; ++ led-gpios = <&gpio 18 1>; ++ ++ gamma = "04 1F 4 7 7 0 7 7 6 0\n0F 00 1 7 4 0 0 0 6 7"; ++ ++ init = <0x10000e7 0x0010 ++ 0x1000000 0x0001 ++ 0x1000001 0x0100 ++ 0x1000002 0x0700 ++ 0x1000003 0x1030 ++ 0x1000004 0x0000 ++ 0x1000008 0x0207 ++ 0x1000009 0x0000 ++ 0x100000a 0x0000 ++ 0x100000c 0x0001 ++ 0x100000d 0x0000 ++ 0x100000f 0x0000 ++ 0x1000010 0x0000 ++ 0x1000011 0x0007 ++ 0x1000012 0x0000 ++ 0x1000013 0x0000 ++ 0x2000032 ++ 0x1000010 0x1590 ++ 0x1000011 0x0227 ++ 0x2000032 ++ 0x1000012 0x009c ++ 0x2000032 ++ 0x1000013 0x1900 ++ 0x1000029 0x0023 ++ 0x100002b 0x000e ++ 0x2000032 ++ 0x1000020 0x0000 ++ 0x1000021 0x0000 ++ 0x2000032 ++ 0x1000050 0x0000 ++ 0x1000051 0x00ef ++ 0x1000052 0x0000 ++ 0x1000053 0x013f ++ 0x1000060 0xa700 ++ 0x1000061 0x0001 ++ 0x100006a 0x0000 ++ 0x1000080 0x0000 ++ 0x1000081 0x0000 ++ 0x1000082 0x0000 ++ 0x1000083 0x0000 ++ 0x1000084 0x0000 ++ 0x1000085 0x0000 ++ 0x1000090 0x0010 ++ 0x1000092 0x0000 ++ 0x1000093 0x0003 ++ 0x1000095 0x0110 ++ 0x1000097 0x0000 ++ 0x1000098 0x0000 ++ 0x1000007 0x0133 ++ 0x1000020 0x0000 ++ 0x1000021 0x0000 ++ 0x2000064>; ++ debug = <0>; ++ }; ++ ++ hy28b_ts: hy28b-ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <17 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 17 0>; ++ ti,x-plate-ohms = /bits/ 16 <100>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ speed = <&hy28b>,"spi-max-frequency:0"; ++ rotate = <&hy28b>,"rotate:0"; ++ fps = <&hy28b>,"fps:0"; ++ debug = <&hy28b>,"debug:0"; ++ xohms = <&hy28b_ts>,"ti,x-plate-ohms;0"; ++ resetgpio = <&hy28b>,"reset-gpios:4", ++ <&hy28b_pins>, "brcm,pins:4"; ++ ledgpio = <&hy28b>,"led-gpios:4", ++ <&hy28b_pins>, "brcm,pins:8"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i-sabre-q2m-overlay.dts b/arch/arm/boot/dts/overlays/i-sabre-q2m-overlay.dts +new file mode 100644 +index 000000000000..0c4cff354674 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i-sabre-q2m-overlay.dts +@@ -0,0 +1,39 @@ ++// Definitions for I-Sabre Q2M ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&sound>; ++ frag0: __overlay__ { ++ compatible = "audiophonics,i-sabre-q2m"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ i-sabre-codec@48 { ++ #sound-dai-cells = <0>; ++ compatible = "audiophonics,i-sabre-codec"; ++ reg = <0x48>; ++ status = "okay"; ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2c-bcm2708-overlay.dts b/arch/arm/boot/dts/overlays/i2c-bcm2708-overlay.dts +new file mode 100644 +index 000000000000..8204b6b3aef8 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c-bcm2708-overlay.dts +@@ -0,0 +1,13 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ compatible = "brcm,bcm2708-i2c"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts b/arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts +new file mode 100644 +index 000000000000..63231b5d7c0c +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts +@@ -0,0 +1,47 @@ ++// Overlay for i2c_gpio bitbanging host bus. ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ ++ __overlay__ { ++ i2c_gpio: i2c@0 { ++ reg = <0xffffffff>; ++ compatible = "i2c-gpio"; ++ gpios = <&gpio 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN) /* sda */ ++ &gpio 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN) /* scl */ ++ >; ++ i2c-gpio,delay-us = <2>; /* ~100 kHz */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/aliases"; ++ __overlay__ { ++ i2c_gpio = "/i2c@0"; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "/__symbols__"; ++ __overlay__ { ++ i2c_gpio = "/i2c@0"; ++ }; ++ }; ++ ++ __overrides__ { ++ i2c_gpio_sda = <&i2c_gpio>,"gpios:4"; ++ i2c_gpio_scl = <&i2c_gpio>,"gpios:16"; ++ i2c_gpio_delay_us = <&i2c_gpio>,"i2c-gpio,delay-us:0"; ++ bus = <&i2c_gpio>, "reg:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2c-mux-overlay.dts b/arch/arm/boot/dts/overlays/i2c-mux-overlay.dts +new file mode 100644 +index 000000000000..112aed91ecb2 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c-mux-overlay.dts +@@ -0,0 +1,139 @@ ++// Umbrella I2C Mux overlay ++ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pca9542: mux@70 { ++ compatible = "nxp,pca9542"; ++ reg = <0x70>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ i2c@0 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <0>; ++ }; ++ i2c@1 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <1>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pca9545: mux@70 { ++ compatible = "nxp,pca9545"; ++ reg = <0x70>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ i2c@0 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <0>; ++ }; ++ i2c@1 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <1>; ++ }; ++ i2c@2 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <2>; ++ }; ++ i2c@3 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <3>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pca9548: mux@70 { ++ compatible = "nxp,pca9548"; ++ reg = <0x70>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ i2c@0 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <0>; ++ }; ++ i2c@1 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <1>; ++ }; ++ i2c@2 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <2>; ++ }; ++ i2c@3 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <3>; ++ }; ++ i2c@4 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <4>; ++ }; ++ i2c@5 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <5>; ++ }; ++ i2c@6 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <6>; ++ }; ++ i2c@7 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ reg = <7>; ++ }; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ pca9542 = <0>, "+0"; ++ pca9545 = <0>, "+1"; ++ pca9548 = <0>, "+2"; ++ ++ addr = <&pca9542>,"reg:0", ++ <&pca9545>,"reg:0", ++ <&pca9548>,"reg:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2c-pwm-pca9685a-overlay.dts b/arch/arm/boot/dts/overlays/i2c-pwm-pca9685a-overlay.dts +new file mode 100644 +index 000000000000..9bb16465a50e +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c-pwm-pca9685a-overlay.dts +@@ -0,0 +1,26 @@ ++// Definitions for NXP PCA9685A I2C PWM controller on ARM I2C bus. ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pca: pca@40 { ++ compatible = "nxp,pca9685-pwm"; ++ #pwm-cells = <2>; ++ reg = <0x40>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ __overrides__ { ++ addr = <&pca>,"reg:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2c-rtc-gpio-overlay.dts b/arch/arm/boot/dts/overlays/i2c-rtc-gpio-overlay.dts +new file mode 100644 +index 000000000000..227e3c0fa1cd +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c-rtc-gpio-overlay.dts +@@ -0,0 +1,266 @@ ++// Definitions for several I2C based Real Time Clocks ++// Available through i2c-gpio ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ i2c_gpio: i2c-gpio-rtc@0 { ++ compatible = "i2c-gpio"; ++ gpios = <&gpio 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN) /* sda */ ++ &gpio 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN) /* scl */ ++ >; ++ i2c-gpio,delay-us = <2>; /* ~100 kHz */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c_gpio>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ abx80x: abx80x@69 { ++ compatible = "abracon,abx80x"; ++ reg = <0x69>; ++ abracon,tc-diode = "standard"; ++ abracon,tc-resistor = <0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c_gpio>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ds1307: ds1307@68 { ++ compatible = "dallas,ds1307"; ++ reg = <0x68>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c_gpio>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ds1339: ds1339@68 { ++ compatible = "dallas,ds1339"; ++ trickle-resistor-ohms = <0>; ++ reg = <0x68>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c_gpio>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ds3231: ds3231@68 { ++ compatible = "maxim,ds3231"; ++ reg = <0x68>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&i2c_gpio>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ mcp7940x: mcp7940x@6f { ++ compatible = "microchip,mcp7940x"; ++ reg = <0x6f>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&i2c_gpio>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ mcp7941x: mcp7941x@6f { ++ compatible = "microchip,mcp7941x"; ++ reg = <0x6f>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@7 { ++ target = <&i2c_gpio>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcf2127@51 { ++ compatible = "nxp,pcf2127"; ++ reg = <0x51>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@8 { ++ target = <&i2c_gpio>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcf8523: pcf8523@68 { ++ compatible = "nxp,pcf8523"; ++ reg = <0x68>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@9 { ++ target = <&i2c_gpio>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcf8563: pcf8563@51 { ++ compatible = "nxp,pcf8563"; ++ reg = <0x51>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@10 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ m41t62: m41t62@68 { ++ compatible = "st,m41t62"; ++ reg = <0x68>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@11 { ++ target = <&i2c_gpio>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ rv3028: rv3028@52 { ++ compatible = "microcrystal,rv3028"; ++ reg = <0x52>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@12 { ++ target = <&i2c_gpio>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcf2129@51 { ++ compatible = "nxp,pcf2129"; ++ reg = <0x51>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@13 { ++ target = <&i2c_gpio>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ rv1805: rv1805@69 { ++ compatible = "microcrystal,rv1805"; ++ reg = <0x69>; ++ abracon,tc-diode = "standard"; ++ abracon,tc-resistor = <0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ abx80x = <0>,"+1"; ++ ds1307 = <0>,"+2"; ++ ds1339 = <0>,"+3"; ++ ds3231 = <0>,"+4"; ++ mcp7940x = <0>,"+5"; ++ mcp7941x = <0>,"+6"; ++ pcf2127 = <0>,"+7"; ++ pcf8523 = <0>,"+8"; ++ pcf8563 = <0>,"+9"; ++ m41t62 = <0>,"+10"; ++ rv3028 = <0>,"+11"; ++ pcf2129 = <0>,"+12"; ++ rv1805 = <0>,"+13"; ++ ++ addr = <&abx80x>, "reg:0", ++ <&ds1307>, "reg:0", ++ <&ds1339>, "reg:0", ++ <&ds3231>, "reg:0", ++ <&mcp7940x>, "reg:0", ++ <&mcp7941x>, "reg:0", ++ <&pcf8523>, "reg:0", ++ <&pcf8563>, "reg:0", ++ <&m41t62>, "reg:0", ++ <&rv1805>, "reg:0"; ++ trickle-diode-type = <&abx80x>,"abracon,tc-diode", ++ <&rv1805>,"abracon,tc-diode"; ++ trickle-resistor-ohms = <&ds1339>,"trickle-resistor-ohms:0", ++ <&abx80x>,"abracon,tc-resistor:0", ++ <&rv3028>,"trickle-resistor-ohms:0", ++ <&rv1805>,"abracon,tc-resistor:0"; ++ backup-switchover-mode = <&rv3028>,"backup-switchover-mode:0"; ++ wakeup-source = <&ds1339>,"wakeup-source?", ++ <&ds3231>,"wakeup-source?", ++ <&mcp7940x>,"wakeup-source?", ++ <&mcp7941x>,"wakeup-source?"; ++ i2c_gpio_sda = <&i2c_gpio>,"gpios:4"; ++ i2c_gpio_scl = <&i2c_gpio>,"gpios:16"; ++ i2c_gpio_delay_us = <&i2c_gpio>,"i2c-gpio,delay-us:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts b/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts +new file mode 100644 +index 000000000000..735ca303e4fa +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c-rtc-overlay.dts +@@ -0,0 +1,278 @@ ++// Definitions for several I2C based Real Time Clocks ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ abx80x: abx80x@69 { ++ compatible = "abracon,abx80x"; ++ reg = <0x69>; ++ abracon,tc-diode = "standard"; ++ abracon,tc-resistor = <0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ds1307: ds1307@68 { ++ compatible = "dallas,ds1307"; ++ reg = <0x68>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ds1339: ds1339@68 { ++ compatible = "dallas,ds1339"; ++ trickle-resistor-ohms = <0>; ++ reg = <0x68>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ds3231: ds3231@68 { ++ compatible = "maxim,ds3231"; ++ reg = <0x68>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ mcp7940x: mcp7940x@6f { ++ compatible = "microchip,mcp7940x"; ++ reg = <0x6f>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ mcp7941x: mcp7941x@6f { ++ compatible = "microchip,mcp7941x"; ++ reg = <0x6f>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcf2127@51 { ++ compatible = "nxp,pcf2127"; ++ reg = <0x51>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@7 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcf8523: pcf8523@68 { ++ compatible = "nxp,pcf8523"; ++ reg = <0x68>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@8 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcf8563: pcf8563@51 { ++ compatible = "nxp,pcf8563"; ++ reg = <0x51>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@9 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ m41t62: m41t62@68 { ++ compatible = "st,m41t62"; ++ reg = <0x68>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@10 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ rv3028: rv3028@52 { ++ compatible = "microcrystal,rv3028"; ++ reg = <0x52>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@11 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcf2129@51 { ++ compatible = "nxp,pcf2129"; ++ reg = <0x51>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@12 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcf85363@51 { ++ compatible = "nxp,pcf85363"; ++ reg = <0x51>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@13 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ rv1805: rv1805@69 { ++ compatible = "microcrystal,rv1805"; ++ reg = <0x69>; ++ abracon,tc-diode = "standard"; ++ abracon,tc-resistor = <0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@14 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ sd3078: sd3078@32 { ++ compatible = "whwave,sd3078"; ++ reg = <0x32>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ abx80x = <0>,"+0"; ++ ds1307 = <0>,"+1"; ++ ds1339 = <0>,"+2"; ++ ds3231 = <0>,"+3"; ++ mcp7940x = <0>,"+4"; ++ mcp7941x = <0>,"+5"; ++ pcf2127 = <0>,"+6"; ++ pcf8523 = <0>,"+7"; ++ pcf8563 = <0>,"+8"; ++ m41t62 = <0>,"+9"; ++ rv3028 = <0>,"+10"; ++ pcf2129 = <0>,"+11"; ++ pcf85363 = <0>,"+12"; ++ rv1805 = <0>,"+13"; ++ sd3078 = <0>,"+14"; ++ ++ addr = <&abx80x>, "reg:0", ++ <&ds1307>, "reg:0", ++ <&ds1339>, "reg:0", ++ <&ds3231>, "reg:0", ++ <&mcp7940x>, "reg:0", ++ <&mcp7941x>, "reg:0", ++ <&pcf8523>, "reg:0", ++ <&pcf8563>, "reg:0", ++ <&m41t62>, "reg:0", ++ <&rv1805>, "reg:0"; ++ trickle-diode-type = <&abx80x>,"abracon,tc-diode", ++ <&rv1805>,"abracon,tc-diode"; ++ trickle-resistor-ohms = <&ds1339>,"trickle-resistor-ohms:0", ++ <&abx80x>,"abracon,tc-resistor:0", ++ <&rv3028>,"trickle-resistor-ohms:0", ++ <&rv1805>,"abracon,tc-resistor:0"; ++ backup-switchover-mode = <&rv3028>,"backup-switchover-mode:0"; ++ wakeup-source = <&ds1339>,"wakeup-source?", ++ <&ds3231>,"wakeup-source?", ++ <&mcp7940x>,"wakeup-source?", ++ <&mcp7941x>,"wakeup-source?", ++ <&m41t62>,"wakeup-source?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2c-sensor-overlay.dts b/arch/arm/boot/dts/overlays/i2c-sensor-overlay.dts +new file mode 100644 +index 000000000000..ce97837b0db5 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c-sensor-overlay.dts +@@ -0,0 +1,271 @@ ++// Definitions for I2C based sensors using the Industrial IO or HWMON interface. ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ bme280: bme280@76 { ++ compatible = "bosch,bme280"; ++ reg = <0x76>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ bmp085: bmp085@77 { ++ compatible = "bosch,bmp085"; ++ reg = <0x77>; ++ default-oversampling = <3>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ bmp180: bmp180@77 { ++ compatible = "bosch,bmp180"; ++ reg = <0x77>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ bmp280: bmp280@76 { ++ compatible = "bosch,bmp280"; ++ reg = <0x76>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ htu21: htu21@40 { ++ compatible = "htu21"; ++ reg = <0x40>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ lm75: lm75@4f { ++ compatible = "lm75"; ++ reg = <0x4f>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ si7020: si7020@40 { ++ compatible = "si7020"; ++ reg = <0x40>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@7 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ tmp102: tmp102@48 { ++ compatible = "ti,tmp102"; ++ reg = <0x48>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@8 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ hdc100x: hdc100x@40 { ++ compatible = "hdc100x"; ++ reg = <0x40>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@9 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ tsl4531: tsl4531@29 { ++ compatible = "tsl4531"; ++ reg = <0x29>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@10 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ veml6070: veml6070@38 { ++ compatible = "veml6070"; ++ reg = <0x38>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@11 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ sht3x: sht3x@44 { ++ compatible = "sht3x"; ++ reg = <0x44>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@12 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ds1621: ds1621@48 { ++ compatible = "ds1621"; ++ reg = <0x48>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@13 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ max17040: max17040@36 { ++ compatible = "maxim,max17040"; ++ reg = <0x36>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@14 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ bme680: bme680@76 { ++ compatible = "bosch,bme680"; ++ reg = <0x76>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@15 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ sps30: sps30@69 { ++ compatible = "sensirion,sps30"; ++ reg = <0x69>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ addr = <&bme280>,"reg:0", <&bmp280>,"reg:0", <&tmp102>,"reg:0", ++ <&lm75>,"reg:0", <&hdc100x>,"reg:0", <&sht3x>,"reg:0", ++ <&ds1621>,"reg:0", <&bme680>,"reg:0"; ++ bme280 = <0>,"+0"; ++ bmp085 = <0>,"+1"; ++ bmp180 = <0>,"+2"; ++ bmp280 = <0>,"+3"; ++ htu21 = <0>,"+4"; ++ lm75 = <0>,"+5"; ++ lm75addr = <&lm75>,"reg:0"; ++ si7020 = <0>,"+6"; ++ tmp102 = <0>,"+7"; ++ hdc100x = <0>,"+8"; ++ tsl4531 = <0>,"+9"; ++ veml6070 = <0>,"+10"; ++ sht3x = <0>,"+11"; ++ ds1621 = <0>,"+12"; ++ max17040 = <0>,"+13"; ++ bme680 = <0>,"+14"; ++ sps30 = <0>,"+15"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2c0-overlay.dts b/arch/arm/boot/dts/overlays/i2c0-overlay.dts +new file mode 100644 +index 000000000000..7c6771f84d8e +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c0-overlay.dts +@@ -0,0 +1,74 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c0if>; ++ __overlay__ { ++ status = "okay"; ++ pinctrl-0 = <&i2c0_pins>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c0_pins>; ++ pins1: __overlay__ { ++ brcm,pins = <0 1>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c0_pins>; ++ pins2: __dormant__ { ++ brcm,pins = <28 29>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c0_pins>; ++ pins3: __dormant__ { ++ brcm,pins = <44 45>; ++ brcm,function = <5>; /* alt1 */ ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c0_pins>; ++ pins4: __dormant__ { ++ brcm,pins = <46 47>; ++ brcm,function = <4>; /* alt0 */ ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&i2c0>; ++ __dormant__ { ++ compatible = "brcm,bcm2708-i2c"; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&i2c0mux>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@7 { ++ target-path = "/aliases"; ++ __overlay__ { ++ i2c0 = "/soc/i2c@7e205000"; ++ }; ++ }; ++ __overrides__ { ++ pins_0_1 = <0>,"+1-2-3-4"; ++ pins_28_29 = <0>,"-1+2-3-4"; ++ pins_44_45 = <0>,"-1-2+3-4"; ++ pins_46_47 = <0>,"-1-2-3+4"; ++ combine = <0>, "!5"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2c1-overlay.dts b/arch/arm/boot/dts/overlays/i2c1-overlay.dts +new file mode 100644 +index 000000000000..addaed73e665 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c1-overlay.dts +@@ -0,0 +1,44 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c1>; ++ __overlay__ { ++ status = "okay"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c1_pins>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1_pins>; ++ pins1: __overlay__ { ++ brcm,pins = <2 3>; ++ brcm,function = <4>; /* alt 0 */ ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1_pins>; ++ pins2: __dormant__ { ++ brcm,pins = <44 45>; ++ brcm,function = <6>; /* alt 2 */ ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c1>; ++ __dormant__ { ++ compatible = "brcm,bcm2708-i2c"; ++ }; ++ }; ++ ++ __overrides__ { ++ pins_2_3 = <0>,"=1!2"; ++ pins_44_45 = <0>,"!1=2"; ++ combine = <0>, "!3"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2c3-overlay.dts b/arch/arm/boot/dts/overlays/i2c3-overlay.dts +new file mode 100644 +index 000000000000..e24a1df21f99 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c3-overlay.dts +@@ -0,0 +1,36 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&i2c3>; ++ frag0: __overlay__ { ++ status = "okay"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c3_pins>; ++ clock-frequency = <100000>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c3_pins>; ++ __dormant__ { ++ brcm,pins = <2 3>; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c3_pins>; ++ __overlay__ { ++ brcm,pins = <4 5>; ++ }; ++ }; ++ ++ __overrides__ { ++ pins_2_3 = <0>,"=1!2"; ++ pins_4_5 = <0>,"!1=2"; ++ baudrate = <&frag0>, "clock-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2c4-overlay.dts b/arch/arm/boot/dts/overlays/i2c4-overlay.dts +new file mode 100644 +index 000000000000..14c7f4d1da4c +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c4-overlay.dts +@@ -0,0 +1,36 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&i2c4>; ++ frag0: __overlay__ { ++ status = "okay"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c4_pins>; ++ clock-frequency = <100000>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c4_pins>; ++ __dormant__ { ++ brcm,pins = <6 7>; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c4_pins>; ++ __overlay__ { ++ brcm,pins = <8 9>; ++ }; ++ }; ++ ++ __overrides__ { ++ pins_6_7 = <0>,"=1!2"; ++ pins_8_9 = <0>,"!1=2"; ++ baudrate = <&frag0>, "clock-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2c5-overlay.dts b/arch/arm/boot/dts/overlays/i2c5-overlay.dts +new file mode 100644 +index 000000000000..7953621112de +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c5-overlay.dts +@@ -0,0 +1,36 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&i2c5>; ++ frag0: __overlay__ { ++ status = "okay"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c5_pins>; ++ clock-frequency = <100000>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c5_pins>; ++ __dormant__ { ++ brcm,pins = <10 11>; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c5_pins>; ++ __overlay__ { ++ brcm,pins = <12 13>; ++ }; ++ }; ++ ++ __overrides__ { ++ pins_10_11 = <0>,"=1!2"; ++ pins_12_13 = <0>,"!1=2"; ++ baudrate = <&frag0>, "clock-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2c6-overlay.dts b/arch/arm/boot/dts/overlays/i2c6-overlay.dts +new file mode 100644 +index 000000000000..555305a7ee1f +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2c6-overlay.dts +@@ -0,0 +1,36 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&i2c6>; ++ frag0: __overlay__ { ++ status = "okay"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&i2c6_pins>; ++ clock-frequency = <100000>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c6_pins>; ++ __dormant__ { ++ brcm,pins = <0 1>; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c6_pins>; ++ __overlay__ { ++ brcm,pins = <22 23>; ++ }; ++ }; ++ ++ __overrides__ { ++ pins_0_1 = <0>,"=1!2"; ++ pins_22_23 = <0>,"!1=2"; ++ baudrate = <&frag0>, "clock-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/i2s-gpio28-31-overlay.dts b/arch/arm/boot/dts/overlays/i2s-gpio28-31-overlay.dts +new file mode 100644 +index 000000000000..cf43094c6ff4 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/i2s-gpio28-31-overlay.dts +@@ -0,0 +1,18 @@ ++/* ++ * Device tree overlay to move i2s to gpio 28 to 31 on CM ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s_pins>; ++ __overlay__ { ++ brcm,pins = <28 29 30 31>; ++ brcm,function = <6>; /* alt2 */ ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/ilitek251x-overlay.dts b/arch/arm/boot/dts/overlays/ilitek251x-overlay.dts +new file mode 100644 +index 000000000000..551aba591d26 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ilitek251x-overlay.dts +@@ -0,0 +1,45 @@ ++// Device tree overlay for I2C connected Ilitek multiple touch controller ++/dts-v1/; ++/plugin/; ++ ++ / { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ ili251x_pins: ili251x_pins { ++ brcm,pins = <4>; // interrupt ++ brcm,function = <0>; // in ++ brcm,pull = <2>; // pull-up // ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ili251x: ili251x@41 { ++ compatible = "ilitek,ili251x"; ++ reg = <0x41>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&ili251x_pins>; ++ interrupt-parent = <&gpio>; ++ interrupts = <4 8>; // high-to-low edge triggered ++ touchscreen-size-x = <16384>; ++ touchscreen-size-y = <9600>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ interrupt = <&ili251x_pins>,"brcm,pins:0", ++ <&ili251x>,"interrupts:0"; ++ sizex = <&ili251x>,"touchscreen-size-x:0"; ++ sizey = <&ili251x>,"touchscreen-size-y:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/imx219-overlay.dts b/arch/arm/boot/dts/overlays/imx219-overlay.dts +new file mode 100644 +index 000000000000..3484bde5a9e8 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/imx219-overlay.dts +@@ -0,0 +1,119 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Definitions for IMX219 camera module on VC I2C bus ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_csi_dsi>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ imx219: imx219@10 { ++ compatible = "sony,imx219"; ++ reg = <0x10>; ++ status = "okay"; ++ ++ clocks = <&imx219_clk>; ++ clock-names = "xclk"; ++ ++ VANA-supply = <&imx219_vana>; /* 2.8v */ ++ VDIG-supply = <&imx219_vdig>; /* 1.8v */ ++ VDDL-supply = <&imx219_vddl>; /* 1.2v */ ++ ++ rotation = <180>; ++ ++ port { ++ imx219_0: endpoint { ++ remote-endpoint = <&csi1_ep>; ++ clock-lanes = <0>; ++ data-lanes = <1 2>; ++ clock-noncontinuous; ++ link-frequencies = ++ /bits/ 64 <297000000>; ++ }; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&csi1>; ++ __overlay__ { ++ status = "okay"; ++ ++ port { ++ csi1_ep: endpoint { ++ remote-endpoint = <&imx219_0>; ++ clock-lanes = <0>; ++ data-lanes = <1 2>; ++ clock-noncontinuous; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c0if>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path="/"; ++ __overlay__ { ++ imx219_vana: fixedregulator@0 { ++ compatible = "regulator-fixed"; ++ regulator-name = "imx219_vana"; ++ regulator-min-microvolt = <2800000>; ++ regulator-max-microvolt = <2800000>; ++ gpio = <&gpio 41 GPIO_ACTIVE_HIGH>; ++ enable-active-high; ++ }; ++ imx219_vdig: fixedregulator@1 { ++ compatible = "regulator-fixed"; ++ regulator-name = "imx219_vdig"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ }; ++ imx219_vddl: fixedregulator@2 { ++ compatible = "regulator-fixed"; ++ regulator-name = "imx219_vddl"; ++ regulator-min-microvolt = <1200000>; ++ regulator-max-microvolt = <1200000>; ++ }; ++ ++ imx219_clk: camera-clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <24000000>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c0mux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path="/__overrides__"; ++ __overlay__ { ++ cam0-pwdn-ctrl = <&imx219_vana>,"gpio:0"; ++ cam0-pwdn = <&imx219_vana>,"gpio:4"; ++ }; ++ }; ++ ++ __overrides__ { ++ rotation = <&imx219>,"rotation:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/imx290-overlay.dts b/arch/arm/boot/dts/overlays/imx290-overlay.dts +new file mode 100644 +index 000000000000..e536aa7f9e33 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/imx290-overlay.dts +@@ -0,0 +1,32 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Definitions for IMX290 camera module on VC I2C bus ++/dts-v1/; ++/plugin/; ++ ++#include ++#include "imx290_327-overlay.dtsi" ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ // Fragment numbers deliberately high to avoid conflicts with the ++ // included imx290_327 overlay file. ++ ++ fragment@101 { ++ target = <&imx290>; ++ __overlay__ { ++ compatible = "sony,imx290"; ++ }; ++ }; ++ ++ fragment@102 { ++ target = <&imx290>; ++ __dormant__ { ++ compatible = "sony,imx290-mono"; ++ }; ++ }; ++ ++ __overrides__ { ++ mono = <0>, "-101+102"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/imx290_327-overlay.dtsi b/arch/arm/boot/dts/overlays/imx290_327-overlay.dtsi +new file mode 100644 +index 000000000000..8f1dadb13f6a +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/imx290_327-overlay.dtsi +@@ -0,0 +1,145 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Partial definitions for IMX290 or IMX327 camera module on VC I2C bus ++// The compatible string should be set in an overlay that then includes this one ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_csi_dsi>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ imx290: imx290@1a { ++ reg = <0x1a>; ++ status = "okay"; ++ ++ clocks = <&imx290_clk>; ++ clock-names = "xclk"; ++ clock-frequency = <37125000>; ++ ++ vdda-supply = <&imx290_vdda>; /* 2.8v */ ++ vdddo-supply = <&imx290_vdddo>; /* 1.8v */ ++ vddd-supply = <&imx290_vddd>; /* 1.5v */ ++ ++ port { ++ imx290_0: endpoint { ++ remote-endpoint = <&csi1_ep>; ++ clock-lanes = <0>; ++ }; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&csi1>; ++ __overlay__ { ++ status = "okay"; ++ ++ port { ++ csi1_ep: endpoint { ++ remote-endpoint = <&imx290_0>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c0if>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path="/"; ++ __overlay__ { ++ imx290_vdda: fixedregulator@0 { ++ compatible = "regulator-fixed"; ++ regulator-name = "imx290_vdda"; ++ regulator-min-microvolt = <2800000>; ++ regulator-max-microvolt = <2800000>; ++ gpio = <&gpio 41 GPIO_ACTIVE_HIGH>; ++ enable-active-high; ++ }; ++ imx290_vdddo: fixedregulator@1 { ++ compatible = "regulator-fixed"; ++ regulator-name = "imx290_vdddo"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ }; ++ imx290_vddd: fixedregulator@2 { ++ compatible = "regulator-fixed"; ++ regulator-name = "imx290_vddd"; ++ regulator-min-microvolt = <1500000>; ++ regulator-max-microvolt = <1500000>; ++ }; ++ ++ imx290_clk: camera-clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <37125000>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c0mux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path="/__overrides__"; ++ __overlay__ { ++ cam0-pwdn-ctrl = <&imx290_vdda>,"gpio:0"; ++ cam0-pwdn = <&imx290_vdda>,"gpio:4"; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&imx290_0>; ++ __overlay__ { ++ data-lanes = <1 2>; ++ link-frequencies = ++ /bits/ 64 <445500000 297000000>; ++ }; ++ }; ++ ++ fragment@7 { ++ target = <&imx290_0>; ++ __dormant__ { ++ data-lanes = <1 2 3 4>; ++ link-frequencies = ++ /bits/ 64 <222750000 148500000>; ++ }; ++ }; ++ ++ fragment@8 { ++ target = <&csi1_ep>; ++ __overlay__ { ++ data-lanes = <1 2>; ++ }; ++ }; ++ ++ fragment@9 { ++ target = <&csi1_ep>; ++ __dormant__ { ++ data-lanes = <1 2 3 4>; ++ }; ++ }; ++ ++ __overrides__ { ++ 4lane = <0>, "-6+7-8+9"; ++ clock-frequency = <&imx290_clk>,"clock-frequency:0", ++ <&imx290>,"clock-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/imx477-overlay.dts b/arch/arm/boot/dts/overlays/imx477-overlay.dts +new file mode 100644 +index 000000000000..1a97eaaf4c82 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/imx477-overlay.dts +@@ -0,0 +1,119 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Definitions for IMX477 camera module on VC I2C bus ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_csi_dsi>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ imx477: imx477@1a { ++ compatible = "sony,imx477"; ++ reg = <0x1a>; ++ status = "okay"; ++ ++ clocks = <&imx477_clk>; ++ clock-names = "xclk"; ++ ++ VANA-supply = <&imx477_vana>; /* 2.8v */ ++ VDIG-supply = <&imx477_vdig>; /* 1.05v */ ++ VDDL-supply = <&imx477_vddl>; /* 1.8v */ ++ ++ rotation = <180>; ++ ++ port { ++ imx477_0: endpoint { ++ remote-endpoint = <&csi1_ep>; ++ clock-lanes = <0>; ++ data-lanes = <1 2>; ++ clock-noncontinuous; ++ link-frequencies = ++ /bits/ 64 <450000000>; ++ }; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&csi1>; ++ __overlay__ { ++ status = "okay"; ++ ++ port { ++ csi1_ep: endpoint { ++ remote-endpoint = <&imx477_0>; ++ clock-lanes = <0>; ++ data-lanes = <1 2>; ++ clock-noncontinuous; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c0if>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path="/"; ++ __overlay__ { ++ imx477_vana: fixedregulator@0 { ++ compatible = "regulator-fixed"; ++ regulator-name = "imx477_vana"; ++ regulator-min-microvolt = <2800000>; ++ regulator-max-microvolt = <2800000>; ++ gpio = <&gpio 41 GPIO_ACTIVE_HIGH>; ++ enable-active-high; ++ startup-delay-us = <300000>; ++ }; ++ imx477_vdig: fixedregulator@1 { ++ compatible = "regulator-fixed"; ++ regulator-name = "imx477_vdig"; ++ regulator-min-microvolt = <1050000>; ++ regulator-max-microvolt = <1050000>; ++ }; ++ imx477_vddl: fixedregulator@2 { ++ compatible = "regulator-fixed"; ++ regulator-name = "imx477_vddl"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ }; ++ imx477_clk: camera-clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <24000000>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c0mux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path="/__overrides__"; ++ __overlay__ { ++ cam0-pwdn-ctrl = <&imx477_vana>,"gpio:0"; ++ cam0-pwdn = <&imx477_vana>,"gpio:4"; ++ }; ++ }; ++ ++ __overrides__ { ++ rotation = <&imx477>,"rotation:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/iqaudio-codec-overlay.dts b/arch/arm/boot/dts/overlays/iqaudio-codec-overlay.dts +new file mode 100644 +index 000000000000..9110f5d34298 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/iqaudio-codec-overlay.dts +@@ -0,0 +1,42 @@ ++// Definitions for IQaudIO CODEC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ da2713@1a { ++ #sound-dai-cells = <0>; ++ compatible = "dlg,da7213"; ++ reg = <0x1a>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ iqaudio_dac: __overlay__ { ++ compatible = "iqaudio,iqaudio-codec"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts b/arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts +new file mode 100644 +index 000000000000..24073cadd0ef +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/iqaudio-dac-overlay.dts +@@ -0,0 +1,46 @@ ++// Definitions for IQaudIO DAC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4c { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4c>; ++ AVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ CPVDD-supply = <&vdd_3v3_reg>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ frag2: __overlay__ { ++ compatible = "iqaudio,iqaudio-dac"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = <&frag2>,"iqaudio,24db_digital_gain?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts b/arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts +new file mode 100644 +index 000000000000..7c70b25e58d7 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/iqaudio-dacplus-overlay.dts +@@ -0,0 +1,49 @@ ++// Definitions for IQaudIO DAC+ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4c { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4c>; ++ AVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ CPVDD-supply = <&vdd_3v3_reg>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ iqaudio_dac: __overlay__ { ++ compatible = "iqaudio,iqaudio-dac"; ++ i2s-controller = <&i2s>; ++ mute-gpios = <&gpio 22 0>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = <&iqaudio_dac>,"iqaudio,24db_digital_gain?"; ++ auto_mute_amp = <&iqaudio_dac>,"iqaudio-dac,auto-mute-amp?"; ++ unmute_amp = <&iqaudio_dac>,"iqaudio-dac,unmute-amp?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/iqaudio-digi-wm8804-audio-overlay.dts b/arch/arm/boot/dts/overlays/iqaudio-digi-wm8804-audio-overlay.dts +new file mode 100644 +index 000000000000..ee54095c869b +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/iqaudio-digi-wm8804-audio-overlay.dts +@@ -0,0 +1,47 @@ ++// Definitions for IQAudIO Digi WM8804 audio board ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8804@3b { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8804"; ++ reg = <0x3b>; ++ status = "okay"; ++ DVDD-supply = <&vdd_3v3_reg>; ++ PVDD-supply = <&vdd_3v3_reg>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ wm8804_digi: __overlay__ { ++ compatible = "iqaudio,wm8804-digi"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ card_name = <&wm8804_digi>,"wm8804-digi,card-name"; ++ dai_name = <&wm8804_digi>,"wm8804-digi,dai-name"; ++ dai_stream_name = <&wm8804_digi>,"wm8804-digi,dai-stream-name"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/irs1125-overlay.dts b/arch/arm/boot/dts/overlays/irs1125-overlay.dts +new file mode 100644 +index 000000000000..e926e18e71fc +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/irs1125-overlay.dts +@@ -0,0 +1,85 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Definitions for IRS1125 camera module on VC I2C bus ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_csi_dsi>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ irs1125: irs1125@3D { ++ compatible = "infineon,irs1125"; ++ reg = <0x3D>; ++ status = "okay"; ++ ++ pwdn-gpios = <&gpio 5 0>; ++ clocks = <&irs1125_clk>; ++ ++ port { ++ irs1125_0: endpoint { ++ remote-endpoint = <&csi1_ep>; ++ clock-lanes = <0>; ++ data-lanes = <1 2>; ++ clock-noncontinuous; ++ link-frequencies = ++ /bits/ 64 <297000000>; ++ }; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&csi1>; ++ __overlay__ { ++ status = "okay"; ++ ++ port { ++ csi1_ep: endpoint { ++ remote-endpoint = <&irs1125_0>; ++ data-lanes = <1 2>; ++ clock-noncontinuous; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c0if>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c0mux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@4 { ++ target-path="/__overrides__"; ++ __overlay__ { ++ cam0-pwdn-ctrl = <&irs1125>,"pwdn-gpios:0"; ++ cam0-pwdn = <&irs1125>,"pwdn-gpios:4"; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path = "/"; ++ __overlay__ { ++ irs1125_clk: camera-clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <26000000>; ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/jedec-spi-nor-overlay.dts b/arch/arm/boot/dts/overlays/jedec-spi-nor-overlay.dts +new file mode 100644 +index 000000000000..585c7dbcdf7f +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/jedec-spi-nor-overlay.dts +@@ -0,0 +1,309 @@ ++// Overlay for JEDEC SPI-NOR Flash Devices (aka m25p80) ++ ++// dtparams: ++// flash-spi- - Enables flash device on SPI, CS#. ++// flash-fastr-spi- - Enables flash device with fast read capability on SPI, CS#. ++// ++// If devices are present on SPI1 or SPI2, those interfaces must be enabled with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays. ++// ++// Example: A single flash device with fast read capability on SPI0, CS#0: ++// dtoverlay=jedec-spi-nor:flash-fastr-spi0-0 ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ // disable spi-dev on spi0.0 ++ fragment@0 { ++ target = <&spidev0>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi0.1 ++ fragment@1 { ++ target = <&spidev1>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi1.0 ++ fragment@2 { ++ target-path = "spi1/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi1.1 ++ fragment@3 { ++ target-path = "spi1/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi1.2 ++ fragment@4 { ++ target-path = "spi1/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi2.0 ++ fragment@5 { ++ target-path = "spi2/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi2.1 ++ fragment@6 { ++ target-path = "spi2/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi2.2 ++ fragment@7 { ++ target-path = "spi2/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // enable flash on spi0.0 ++ fragment@8 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi_nor_00: spi_nor@0 { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ compatible = "jedec,spi-nor"; ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ // enable flash on spi0.1 ++ fragment@9 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi_nor_01: spi_nor@1 { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ compatible = "jedec,spi-nor"; ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ // enable flash on spi1.0 ++ fragment@10 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi_nor_10: spi_nor@0 { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ compatible = "jedec,spi-nor"; ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ // enable flash on spi1.1 ++ fragment@11 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi_nor_11: spi_nor@1 { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ compatible = "jedec,spi-nor"; ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ // enable flash on spi1.2 ++ fragment@12 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi_nor_12: spi_nor@2 { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ compatible = "jedec,spi-nor"; ++ reg = <2>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ // enable flash on spi2.0 ++ fragment@13 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi_nor_20: spi_nor@0 { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ compatible = "jedec,spi-nor"; ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ // enable flash on spi2.1 ++ fragment@14 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi_nor_21: spi_nor@1 { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ compatible = "jedec,spi-nor"; ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ // enable flash on spi2.2 ++ fragment@15 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi_nor_22: spi_nor@2 { ++ #address-cells = <1>; ++ #size-cells = <1>; ++ compatible = "jedec,spi-nor"; ++ reg = <2>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ // Enable fast read for device on spi0.0. ++ // Use default active low interrupt signalling. ++ fragment@16 { ++ target = <&spi_nor_00>; ++ __dormant__ { ++ m25p,fast-read; ++ }; ++ }; ++ ++ // Enable fast read for device on spi0.1. ++ // Use default active low interrupt signalling. ++ fragment@17 { ++ target = <&spi_nor_01>; ++ __dormant__ { ++ m25p,fast-read; ++ }; ++ }; ++ ++ // Enable fast read for device on spi1.0. ++ // Use default active low interrupt signalling. ++ fragment@18 { ++ target = <&spi_nor_10>; ++ __dormant__ { ++ m25p,fast-read; ++ }; ++ }; ++ ++ // Enable fast read for device on spi1.1. ++ // Use default active low interrupt signalling. ++ fragment@19 { ++ target = <&spi_nor_11>; ++ __dormant__ { ++ m25p,fast-read; ++ }; ++ }; ++ ++ // Enable fast read for device on spi1.2. ++ // Use default active low interrupt signalling. ++ fragment@20 { ++ target = <&spi_nor_12>; ++ __dormant__ { ++ m25p,fast-read; ++ }; ++ }; ++ ++ // Enable fast read for device on spi2.0. ++ // Use default active low interrupt signalling. ++ fragment@21 { ++ target = <&spi_nor_20>; ++ __dormant__ { ++ m25p,fast-read; ++ }; ++ }; ++ ++ // Enable fast read for device on spi2.1. ++ // Use default active low interrupt signalling. ++ fragment@22 { ++ target = <&spi_nor_21>; ++ __dormant__ { ++ m25p,fast-read; ++ }; ++ }; ++ ++ // Enable fast read for device on spi2.2. ++ // Use default active low interrupt signalling. ++ fragment@23 { ++ target = <&spi_nor_22>; ++ __dormant__ { ++ m25p,fast-read; ++ }; ++ }; ++ ++ __overrides__ { ++ flash-spi0-0 = <0>,"+0+8"; ++ flash-spi0-1 = <0>,"+1+9"; ++ flash-spi1-0 = <0>,"+2+10"; ++ flash-spi1-1 = <0>,"+3+11"; ++ flash-spi1-2 = <0>,"+4+12"; ++ flash-spi2-0 = <0>,"+5+13"; ++ flash-spi2-1 = <0>,"+6+14"; ++ flash-spi2-2 = <0>,"+7+15"; ++ flash-fastr-spi0-0 = <0>,"+0+8+16"; ++ flash-fastr-spi0-1 = <0>,"+1+9+17"; ++ flash-fastr-spi1-0 = <0>,"+2+10+18"; ++ flash-fastr-spi1-1 = <0>,"+3+11+19"; ++ flash-fastr-spi1-2 = <0>,"+4+12+20"; ++ flash-fastr-spi2-0 = <0>,"+5+13+21"; ++ flash-fastr-spi2-1 = <0>,"+6+14+22"; ++ flash-fastr-spi2-2 = <0>,"+7+15+23"; ++ }; ++}; ++ +diff --git a/arch/arm/boot/dts/overlays/justboom-both-overlay.dts b/arch/arm/boot/dts/overlays/justboom-both-overlay.dts +new file mode 100644 +index 000000000000..9c42670631c0 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/justboom-both-overlay.dts +@@ -0,0 +1,65 @@ ++// SPDX-License-Identifier: GPL-2.0 ++// Definitions for JustBoom Both (Digi+DAC) ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8804@3b { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8804"; ++ reg = <0x3b>; ++ PVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4d { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4d>; ++ AVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ CPVDD-supply = <&vdd_3v3_reg>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sound>; ++ frag3: __overlay__ { ++ compatible = "justboom,justboom-both"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = <&frag3>,"justboom,24db_digital_gain?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/justboom-dac-overlay.dts b/arch/arm/boot/dts/overlays/justboom-dac-overlay.dts +new file mode 100644 +index 000000000000..d00515dca419 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/justboom-dac-overlay.dts +@@ -0,0 +1,46 @@ ++// Definitions for JustBoom DAC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pcm5122@4d { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5122"; ++ reg = <0x4d>; ++ AVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ CPVDD-supply = <&vdd_3v3_reg>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ frag2: __overlay__ { ++ compatible = "justboom,justboom-dac"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ 24db_digital_gain = <&frag2>,"justboom,24db_digital_gain?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/justboom-digi-overlay.dts b/arch/arm/boot/dts/overlays/justboom-digi-overlay.dts +new file mode 100644 +index 000000000000..e73336029c54 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/justboom-digi-overlay.dts +@@ -0,0 +1,41 @@ ++// Definitions for JustBoom Digi ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8804@3b { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8804"; ++ reg = <0x3b>; ++ PVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "justboom,justboom-digi"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/ltc294x-overlay.dts b/arch/arm/boot/dts/overlays/ltc294x-overlay.dts +new file mode 100644 +index 000000000000..6d971f3649ca +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ltc294x-overlay.dts +@@ -0,0 +1,86 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ltc2941: ltc2941@64 { ++ compatible = "lltc,ltc2941"; ++ reg = <0x64>; ++ lltc,resistor-sense = <50>; ++ lltc,prescaler-exponent = <7>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ltc2942: ltc2942@64 { ++ compatible = "lltc,ltc2942"; ++ reg = <0x64>; ++ lltc,resistor-sense = <50>; ++ lltc,prescaler-exponent = <7>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ltc2943: ltc2943@64 { ++ compatible = "lltc,ltc2943"; ++ reg = <0x64>; ++ lltc,resistor-sense = <50>; ++ lltc,prescaler-exponent = <7>; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c_arm>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ltc2944: ltc2944@64 { ++ compatible = "lltc,ltc2944"; ++ reg = <0x64>; ++ lltc,resistor-sense = <50>; ++ lltc,prescaler-exponent = <7>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ ltc2941 = <0>,"+0"; ++ ltc2942 = <0>,"+1"; ++ ltc2943 = <0>,"+2"; ++ ltc2944 = <0>,"+3"; ++ resistor-sense = <<c2941>, "lltc,resistor-sense:0", ++ <<c2942>, "lltc,resistor-sense:0", ++ <<c2943>, "lltc,resistor-sense:0", ++ <<c2944>, "lltc,resistor-sense:0"; ++ prescaler-exponent = <<c2941>, "lltc,prescaler-exponent:0", ++ <<c2942>, "lltc,prescaler-exponent:0", ++ <<c2943>, "lltc,prescaler-exponent:0", ++ <<c2944>, "lltc,prescaler-exponent:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/max98357a-overlay.dts b/arch/arm/boot/dts/overlays/max98357a-overlay.dts +new file mode 100644 +index 000000000000..9e2afb05b7cb +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/max98357a-overlay.dts +@@ -0,0 +1,84 @@ ++// Overlay for Maxim MAX98357A audio DAC ++ ++// dtparams: ++// no-sdmode - SD_MODE pin not managed by driver. ++// sdmode-pin - Specify GPIO pin to which SD_MODE is connected (default 4). ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ /* Enable I2S */ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ /* DAC whose SD_MODE pin is managed by driver (via GPIO pin) */ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ max98357a_dac: max98357a { ++ compatible = "maxim,max98357a"; ++ #sound-dai-cells = <0>; ++ sdmode-gpios = <&gpio 4 0>; /* 2nd word overwritten by sdmode-pin parameter */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ /* DAC whose SD_MODE pin is not managed by driver */ ++ fragment@2 { ++ target-path = "/"; ++ __dormant__ { ++ max98357a_nsd: max98357a { ++ compatible = "maxim,max98357a"; ++ #sound-dai-cells = <0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ /* Soundcard connecting I2S to DAC with SD_MODE */ ++ fragment@3 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "simple-audio-card"; ++ simple-audio-card,format = "i2s"; ++ simple-audio-card,name = "MAX98357A"; ++ status = "okay"; ++ simple-audio-card,cpu { ++ sound-dai = <&i2s>; ++ }; ++ simple-audio-card,codec { ++ sound-dai = <&max98357a_dac>; ++ }; ++ }; ++ }; ++ ++ /* Soundcard connecting I2S to DAC without SD_MODE */ ++ fragment@4 { ++ target = <&sound>; ++ __dormant__ { ++ compatible = "simple-audio-card"; ++ simple-audio-card,format = "i2s"; ++ simple-audio-card,name = "MAX98357A"; ++ status = "okay"; ++ simple-audio-card,cpu { ++ sound-dai = <&i2s>; ++ }; ++ simple-audio-card,codec { ++ sound-dai = <&max98357a_nsd>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ no-sdmode = <0>,"-1+2-3+4"; ++ sdmode-pin = <&max98357a_dac>,"sdmode-gpios:4"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/maxtherm-overlay.dts b/arch/arm/boot/dts/overlays/maxtherm-overlay.dts +new file mode 100644 +index 000000000000..34d5727069ec +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/maxtherm-overlay.dts +@@ -0,0 +1,166 @@ ++/* ++ * Universal device tree overlay for SPI devices ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spidev0>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev1>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "spi1/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path = "spi1/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@4 { ++ target-path = "spi1/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path = "spi2/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@6 { ++ target-path = "spi2/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@7 { ++ target-path = "spi2/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ maxfrag: fragment@8 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ max: maxtherm@0 { ++ compatible = "maxim,max6675"; ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ }; ++ }; ++ }; ++ ++ fragment@9 { ++ target = <&max>; ++ __dormant__ { ++ compatible = "maxim,max31855e", "maxim,max31855"; ++ }; ++ }; ++ ++ fragment@10 { ++ target = <&max>; ++ __dormant__ { ++ compatible = "maxim,max31855j", "maxim,max31855"; ++ }; ++ }; ++ ++ fragment@11 { ++ target = <&max>; ++ __dormant__ { ++ compatible = "maxim,max31855k", "maxim,max31855"; ++ }; ++ }; ++ ++ fragment@12 { ++ target = <&max>; ++ __dormant__ { ++ compatible = "maxim,max31855n", "maxim,max31855"; ++ }; ++ }; ++ ++ fragment@13 { ++ target = <&max>; ++ __dormant__ { ++ compatible = "maxim,max31855r", "maxim,max31855"; ++ }; ++ }; ++ ++ fragment@14 { ++ target = <&max>; ++ __dormant__ { ++ compatible = "maxim,max31855s", "maxim,max31855"; ++ }; ++ }; ++ ++ fragment@15 { ++ target = <&max>; ++ __dormant__ { ++ compatible = "maxim,max31855t", "maxim,max31855"; ++ }; ++ }; ++ ++ __overrides__ { ++ spi0-0 = <0>, "+0", ++ <&maxfrag>,"target:0=",<&spi0>, ++ <&max>,"reg:0=0"; ++ spi0-1 = <0>, "+1", ++ <&maxfrag>,"target:0=",<&spi0>, ++ <&max>,"reg:0=1"; ++ spi1-0 = <0>, "+2", ++ <&maxfrag>,"target:0=",<&spi1>, ++ <&max>,"reg:0=0"; ++ spi1-1 = <0>, "+3", ++ <&maxfrag>,"target:0=",<&spi1>, ++ <&max>,"reg:0=1"; ++ spi1-2 = <0>, "+4", ++ <&maxfrag>,"target:0=",<&spi1>, ++ <&max>,"reg:0=2"; ++ spi2-0 = <0>, "+5", ++ <&maxfrag>,"target:0=",<&spi2>, ++ <&max>,"reg:0=0"; ++ spi2-1 = <0>, "+6", ++ <&maxfrag>,"target:0=",<&spi2>, ++ <&max>,"reg:0=1"; ++ spi2-2 = <0>, "+7", ++ <&maxfrag>,"target:0=",<&spi2>, ++ <&max>,"reg:0=2"; ++ max6675 = <&max>,"compatible=maxim,max6675"; ++ max31855 = <&max>,"compatible=maxim,max31855"; ++ max31855e = <0>,"+9"; ++ max31855j = <0>,"+10"; ++ max31855k = <0>,"+11"; ++ max31855n = <0>,"+12"; ++ max31855r = <0>,"+13"; ++ max31855s = <0>,"+14"; ++ max31855t = <0>,"+15"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/mbed-dac-overlay.dts b/arch/arm/boot/dts/overlays/mbed-dac-overlay.dts +new file mode 100644 +index 000000000000..840dd9b31db4 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mbed-dac-overlay.dts +@@ -0,0 +1,64 @@ ++// Definitions for mbed DAC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ tlv320aic23: codec@1a { ++ #sound-dai-cells = <0>; ++ reg = <0x1a>; ++ compatible = "ti,tlv320aic23"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "simple-audio-card"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ ++ simple-audio-card,name = "mbed-DAC"; ++ ++ simple-audio-card,widgets = ++ "Microphone", "Mic Jack", ++ "Line", "Line In", ++ "Headphone", "Headphone Jack"; ++ ++ simple-audio-card,routing = ++ "Headphone Jack", "LHPOUT", ++ "Headphone Jack", "RHPOUT", ++ "LLINEIN", "Line In", ++ "RLINEIN", "Line In", ++ "MICIN", "Mic Jack"; ++ ++ simple-audio-card,format = "i2s"; ++ ++ simple-audio-card,cpu { ++ sound-dai = <&i2s>; ++ }; ++ ++ sound_master: simple-audio-card,codec { ++ sound-dai = <&tlv320aic23>; ++ system-clock-frequency = <12288000>; ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/mcp23017-overlay.dts b/arch/arm/boot/dts/overlays/mcp23017-overlay.dts +new file mode 100644 +index 000000000000..c546d8ba7e6d +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mcp23017-overlay.dts +@@ -0,0 +1,69 @@ ++// Definitions for MCP23017 Gpio Extender from Microchip Semiconductor ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c1>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ mcp23017_pins: mcp23017_pins@20 { ++ brcm,pins = <4>; ++ brcm,function = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp23017: mcp@20 { ++ compatible = "microchip,mcp23017"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&mcp23017>; ++ __dormant__ { ++ compatible = "microchip,mcp23008"; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&mcp23017>; ++ mcp23017_irq: __overlay__ { ++ #interrupt-cells=<2>; ++ interrupt-parent = <&gpio>; ++ interrupts = <4 2>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ __overrides__ { ++ gpiopin = <&mcp23017_pins>,"brcm,pins:0", ++ <&mcp23017_irq>,"interrupts:0"; ++ addr = <&mcp23017>,"reg:0", <&mcp23017_pins>,"reg:0"; ++ mcp23008 = <0>,"=3"; ++ noints = <0>,"!1!4"; ++ }; ++}; ++ +diff --git a/arch/arm/boot/dts/overlays/mcp23s17-overlay.dts b/arch/arm/boot/dts/overlays/mcp23s17-overlay.dts +new file mode 100644 +index 000000000000..484d64b225fb +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mcp23s17-overlay.dts +@@ -0,0 +1,732 @@ ++// Overlay for MCP23S08/17 GPIO Extenders from Microchip Semiconductor ++ ++// dtparams: ++// s08-spi--present - 4-bit integer, bitmap indicating MCP23S08 devices present on SPI, CS#. ++// s17-spi--present - 8-bit integer, bitmap indicating MCP23S17 devices present on SPI, CS#. ++// s08-spi--int-gpio - integer, enables interrupts on a single MCP23S08 device on SPI, CS#, specifies the GPIO pin to which INT output is connected. ++// s17-spi--int-gpio - integer, enables mirrored interrupts on a single MCP23S17 device on SPI, CS#, specifies the GPIO pin to which either INTA or INTB output is connected. ++// ++// If devices are present on SPI1 or SPI2, those interfaces must be enabled with one of the spi1-1/2/3cs and/or spi2-1/2/3cs overlays. ++// If interrupts are enabled for a device on a given CS# on a SPI bus, that device must be the only one present on that SPI bus/CS#. ++// ++// Example 1: A single MCP23S17 device on SPI0, CS#0 with its SPI addr set to 0 and INTA output connected to GPIO25: ++// dtoverlay=mcp23s17:s17-spi0-0-present=1,s17-spi0-0-int-gpio=25 ++// ++// Example 2: Two MCP23S08 devices on SPI1, CS#0 with their addrs set to 2 and 3. Three MCP23S17 devices on SPI1, CS#1 with their addrs set to 0, 1 and 7: ++// dtoverlay=spi1-2cs ++// dtoverlay=mcp23s17:s08-spi1-0-present=12,s17-spi1-1-present=131 ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ // disable spi-dev on spi0.0 ++ fragment@0 { ++ target = <&spidev0>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi0.1 ++ fragment@1 { ++ target = <&spidev1>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi1.0 ++ fragment@2 { ++ target-path = "spi1/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi1.1 ++ fragment@3 { ++ target-path = "spi1/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi1.2 ++ fragment@4 { ++ target-path = "spi1/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi2.0 ++ fragment@5 { ++ target-path = "spi2/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi2.1 ++ fragment@6 { ++ target-path = "spi2/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // disable spi-dev on spi2.2 ++ fragment@7 { ++ target-path = "spi2/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi0.0 ++ fragment@8 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_00: mcp23s08@0 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi0-0-present parameter */ ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi0-0-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi0.1 ++ fragment@9 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_01: mcp23s08@1 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi0-1-present parameter */ ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi0-1-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi1.0 ++ fragment@10 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_10: mcp23s08@0 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi1-0-present parameter */ ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi1-0-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi1.1 ++ fragment@11 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_11: mcp23s08@1 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi1-1-present parameter */ ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi1-1-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi1.2 ++ fragment@12 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_12: mcp23s08@2 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi1-2-present parameter */ ++ reg = <2>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi1-2-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi2.0 ++ fragment@13 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_20: mcp23s08@0 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi2-0-present parameter */ ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi2-0-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi2.1 ++ fragment@14 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_21: mcp23s08@1 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi2-1-present parameter */ ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi2-1-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s08s on spi2.2 ++ fragment@15 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s08_22: mcp23s08@2 { ++ compatible = "microchip,mcp23s08"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s08-spi2-2-present parameter */ ++ reg = <2>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s08-spi2-2-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi0.0 ++ fragment@16 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_00: mcp23s17@0 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi0-0-present parameter */ ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi0-0-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi0.1 ++ fragment@17 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_01: mcp23s17@1 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi0-1-present parameter */ ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi0-1-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi1.0 ++ fragment@18 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_10: mcp23s17@0 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi1-0-present parameter */ ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi1-0-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi1.1 ++ fragment@19 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_11: mcp23s17@1 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi1-1-present parameter */ ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi1-1-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi1.2 ++ fragment@20 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_12: mcp23s17@2 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi1-2-present parameter */ ++ reg = <2>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi1-2-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi2.0 ++ fragment@21 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_20: mcp23s17@0 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi2-0-present parameter */ ++ reg = <0>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi2-0-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi2.1 ++ fragment@22 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_21: mcp23s17@1 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi2-1-present parameter */ ++ reg = <1>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi2-1-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // enable one or more mcp23s17s on spi2.2 ++ fragment@23 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ mcp23s17_22: mcp23s17@2 { ++ compatible = "microchip,mcp23s17"; ++ gpio-controller; ++ #gpio-cells = <2>; ++ microchip,spi-present-mask = <0x00>; /* overwritten by mcp23s17-spi2-2-present parameter */ ++ reg = <2>; ++ spi-max-frequency = <500000>; ++ status = "okay"; ++ #interrupt-cells=<2>; ++ interrupts = <0 2>; /* 1st word overwritten by mcp23s17-spi2-2-int-gpio parameter */ ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi0.0 as a input with no pull-up/down ++ fragment@24 { ++ target = <&gpio>; ++ __dormant__ { ++ spi0_0_int_pins: spi0_0_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi0-0-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi0.1 as a input with no pull-up/down ++ fragment@25 { ++ target = <&gpio>; ++ __dormant__ { ++ spi0_1_int_pins: spi0_1_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi0-1-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi1.0 as a input with no pull-up/down ++ fragment@26 { ++ target = <&gpio>; ++ __dormant__ { ++ spi1_0_int_pins: spi1_0_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi1-0-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi1.1 as a input with no pull-up/down ++ fragment@27 { ++ target = <&gpio>; ++ __dormant__ { ++ spi1_1_int_pins: spi1_1_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi1-1-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi1.2 as a input with no pull-up/down ++ fragment@28 { ++ target = <&gpio>; ++ __dormant__ { ++ spi1_2_int_pins: spi1_2_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi1-2-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi2.0 as a input with no pull-up/down ++ fragment@29 { ++ target = <&gpio>; ++ __dormant__ { ++ spi2_0_int_pins: spi2_0_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi2-0-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi2.1 as a input with no pull-up/down ++ fragment@30 { ++ target = <&gpio>; ++ __dormant__ { ++ spi2_1_int_pins: spi2_1_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi2-1-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to INT(A/B) output of mcp23s08/17 on spi2.2 as a input with no pull-up/down ++ fragment@31 { ++ target = <&gpio>; ++ __dormant__ { ++ spi2_2_int_pins: spi2_2_int_pins { ++ brcm,pins = <0>; /* overwritten by mcp23s08/17-spi2-2-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi0.0. ++ // Use default active low interrupt signalling. ++ fragment@32 { ++ target = <&mcp23s08_00>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi0.1. ++ // Use default active low interrupt signalling. ++ fragment@33 { ++ target = <&mcp23s08_01>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi1.0. ++ // Use default active low interrupt signalling. ++ fragment@34 { ++ target = <&mcp23s08_10>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi1.1. ++ // Use default active low interrupt signalling. ++ fragment@35 { ++ target = <&mcp23s08_11>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi1.2. ++ // Use default active low interrupt signalling. ++ fragment@36 { ++ target = <&mcp23s08_12>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi2.0. ++ // Use default active low interrupt signalling. ++ fragment@37 { ++ target = <&mcp23s08_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi2.1. ++ // Use default active low interrupt signalling. ++ fragment@38 { ++ target = <&mcp23s08_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s08 on spi2.2. ++ // Use default active low interrupt signalling. ++ fragment@39 { ++ target = <&mcp23s08_22>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi0.0. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Use default active low interrupt signalling. ++ fragment@40 { ++ target = <&mcp23s17_00>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi0.1. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@41 { ++ target = <&mcp23s17_01>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi1.0. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@42 { ++ target = <&mcp23s17_10>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi1.1. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@43 { ++ target = <&mcp23s17_11>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi1.2. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@44 { ++ target = <&mcp23s17_12>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi2.0. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@45 { ++ target = <&mcp23s17_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi2.1. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@46 { ++ target = <&mcp23s17_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ // Enable interrupts for a mcp23s17 on spi2.2. ++ // Enable mirroring so that either INTA or INTB output of mcp23s17 can be connected to the GPIO pin. ++ // Configure INTA/B outputs of mcp23s08/17 as active low. ++ fragment@47 { ++ target = <&mcp23s17_22>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ microchip,irq-mirror; ++ }; ++ }; ++ ++ __overrides__ { ++ s08-spi0-0-present = <0>,"+0+8", <&mcp23s08_00>,"microchip,spi-present-mask:0"; ++ s08-spi0-1-present = <0>,"+1+9", <&mcp23s08_01>,"microchip,spi-present-mask:0"; ++ s08-spi1-0-present = <0>,"+2+10", <&mcp23s08_10>,"microchip,spi-present-mask:0"; ++ s08-spi1-1-present = <0>,"+3+11", <&mcp23s08_11>,"microchip,spi-present-mask:0"; ++ s08-spi1-2-present = <0>,"+4+12", <&mcp23s08_12>,"microchip,spi-present-mask:0"; ++ s08-spi2-0-present = <0>,"+5+13", <&mcp23s08_20>,"microchip,spi-present-mask:0"; ++ s08-spi2-1-present = <0>,"+6+14", <&mcp23s08_21>,"microchip,spi-present-mask:0"; ++ s08-spi2-2-present = <0>,"+7+15", <&mcp23s08_22>,"microchip,spi-present-mask:0"; ++ s17-spi0-0-present = <0>,"+0+16", <&mcp23s17_00>,"microchip,spi-present-mask:0"; ++ s17-spi0-1-present = <0>,"+1+17", <&mcp23s17_01>,"microchip,spi-present-mask:0"; ++ s17-spi1-0-present = <0>,"+2+18", <&mcp23s17_10>,"microchip,spi-present-mask:0"; ++ s17-spi1-1-present = <0>,"+3+19", <&mcp23s17_11>,"microchip,spi-present-mask:0"; ++ s17-spi1-2-present = <0>,"+4+20", <&mcp23s17_12>,"microchip,spi-present-mask:0"; ++ s17-spi2-0-present = <0>,"+5+21", <&mcp23s17_20>,"microchip,spi-present-mask:0"; ++ s17-spi2-1-present = <0>,"+6+22", <&mcp23s17_21>,"microchip,spi-present-mask:0"; ++ s17-spi2-2-present = <0>,"+7+23", <&mcp23s17_22>,"microchip,spi-present-mask:0"; ++ s08-spi0-0-int-gpio = <0>,"+24+32", <&spi0_0_int_pins>,"brcm,pins:0", <&mcp23s08_00>,"interrupts:0"; ++ s08-spi0-1-int-gpio = <0>,"+25+33", <&spi0_1_int_pins>,"brcm,pins:0", <&mcp23s08_01>,"interrupts:0"; ++ s08-spi1-0-int-gpio = <0>,"+26+34", <&spi1_0_int_pins>,"brcm,pins:0", <&mcp23s08_10>,"interrupts:0"; ++ s08-spi1-1-int-gpio = <0>,"+27+35", <&spi1_1_int_pins>,"brcm,pins:0", <&mcp23s08_11>,"interrupts:0"; ++ s08-spi1-2-int-gpio = <0>,"+28+36", <&spi1_2_int_pins>,"brcm,pins:0", <&mcp23s08_12>,"interrupts:0"; ++ s08-spi2-0-int-gpio = <0>,"+29+37", <&spi2_0_int_pins>,"brcm,pins:0", <&mcp23s08_20>,"interrupts:0"; ++ s08-spi2-1-int-gpio = <0>,"+30+38", <&spi2_1_int_pins>,"brcm,pins:0", <&mcp23s08_21>,"interrupts:0"; ++ s08-spi2-2-int-gpio = <0>,"+31+39", <&spi2_2_int_pins>,"brcm,pins:0", <&mcp23s08_22>,"interrupts:0"; ++ s17-spi0-0-int-gpio = <0>,"+24+40", <&spi0_0_int_pins>,"brcm,pins:0", <&mcp23s17_00>,"interrupts:0"; ++ s17-spi0-1-int-gpio = <0>,"+25+41", <&spi0_1_int_pins>,"brcm,pins:0", <&mcp23s17_01>,"interrupts:0"; ++ s17-spi1-0-int-gpio = <0>,"+26+42", <&spi1_0_int_pins>,"brcm,pins:0", <&mcp23s17_10>,"interrupts:0"; ++ s17-spi1-1-int-gpio = <0>,"+27+43", <&spi1_1_int_pins>,"brcm,pins:0", <&mcp23s17_11>,"interrupts:0"; ++ s17-spi1-2-int-gpio = <0>,"+28+44", <&spi1_2_int_pins>,"brcm,pins:0", <&mcp23s17_12>,"interrupts:0"; ++ s17-spi2-0-int-gpio = <0>,"+29+45", <&spi2_0_int_pins>,"brcm,pins:0", <&mcp23s17_20>,"interrupts:0"; ++ s17-spi2-1-int-gpio = <0>,"+30+46", <&spi2_1_int_pins>,"brcm,pins:0", <&mcp23s17_21>,"interrupts:0"; ++ s17-spi2-2-int-gpio = <0>,"+31+47", <&spi2_2_int_pins>,"brcm,pins:0", <&mcp23s17_22>,"interrupts:0"; ++ }; ++}; ++ +diff --git a/arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts b/arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts +new file mode 100755 +index 000000000000..46f143d809cc +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mcp2515-can0-overlay.dts +@@ -0,0 +1,73 @@ ++/* ++ * Device tree overlay for mcp251x/can0 on spi0.0 ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ /* disable spi-dev for spi0.0 */ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ /* the interrupt pin of the can-controller */ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ can0_pins: can0_pins { ++ brcm,pins = <25>; ++ brcm,function = <0>; /* input */ ++ }; ++ }; ++ }; ++ ++ /* the clock/oscillator of the can-controller */ ++ fragment@3 { ++ target-path = "/"; ++ __overlay__ { ++ /* external oscillator of mcp2515 on SPI0.0 */ ++ can0_osc: can0_osc { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <16000000>; ++ }; ++ }; ++ }; ++ ++ /* the spi config of the can-controller itself binding everything together */ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ can0: mcp2515@0 { ++ reg = <0>; ++ compatible = "microchip,mcp2515"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&can0_pins>; ++ spi-max-frequency = <10000000>; ++ interrupt-parent = <&gpio>; ++ interrupts = <25 8>; /* IRQ_TYPE_LEVEL_LOW */ ++ clocks = <&can0_osc>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ oscillator = <&can0_osc>,"clock-frequency:0"; ++ spimaxfrequency = <&can0>,"spi-max-frequency:0"; ++ interrupt = <&can0_pins>,"brcm,pins:0",<&can0>,"interrupts:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/mcp2515-can1-overlay.dts b/arch/arm/boot/dts/overlays/mcp2515-can1-overlay.dts +new file mode 100644 +index 000000000000..0a8dd576818e +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mcp2515-can1-overlay.dts +@@ -0,0 +1,73 @@ ++/* ++ * Device tree overlay for mcp251x/can1 on spi0.1 edited by petit_miner ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ /* disable spi-dev for spi0.1 */ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ /* the interrupt pin of the can-controller */ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ can1_pins: can1_pins { ++ brcm,pins = <25>; ++ brcm,function = <0>; /* input */ ++ }; ++ }; ++ }; ++ ++ /* the clock/oscillator of the can-controller */ ++ fragment@3 { ++ target-path = "/"; ++ __overlay__ { ++ /* external oscillator of mcp2515 on spi0.1 */ ++ can1_osc: can1_osc { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <16000000>; ++ }; ++ }; ++ }; ++ ++ /* the spi config of the can-controller itself binding everything together */ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ can1: mcp2515@1 { ++ reg = <1>; ++ compatible = "microchip,mcp2515"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&can1_pins>; ++ spi-max-frequency = <10000000>; ++ interrupt-parent = <&gpio>; ++ interrupts = <25 8>; /* IRQ_TYPE_LEVEL_LOW */ ++ clocks = <&can1_osc>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ oscillator = <&can1_osc>,"clock-frequency:0"; ++ spimaxfrequency = <&can1>,"spi-max-frequency:0"; ++ interrupt = <&can1_pins>,"brcm,pins:0",<&can1>,"interrupts:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/mcp3008-overlay.dts b/arch/arm/boot/dts/overlays/mcp3008-overlay.dts +new file mode 100755 +index 000000000000..957fdb9310af +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mcp3008-overlay.dts +@@ -0,0 +1,205 @@ ++/* ++ * Device tree overlay for Microchip mcp3008 10-Bit A/D Converters ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spidev0>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev1>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "spi1/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path = "spi1/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@4 { ++ target-path = "spi1/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path = "spi2/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@6 { ++ target-path = "spi2/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@7 { ++ target-path = "spi2/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@8 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3008_00: mcp3008@0 { ++ compatible = "microchip,mcp3008"; ++ reg = <0>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@9 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3008_01: mcp3008@1 { ++ compatible = "microchip,mcp3008"; ++ reg = <1>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@10 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3008_10: mcp3008@0 { ++ compatible = "microchip,mcp3008"; ++ reg = <0>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@11 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3008_11: mcp3008@1 { ++ compatible = "microchip,mcp3008"; ++ reg = <1>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@12 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3008_12: mcp3008@2 { ++ compatible = "microchip,mcp3008"; ++ reg = <2>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@13 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3008_20: mcp3008@0 { ++ compatible = "microchip,mcp3008"; ++ reg = <0>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@14 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3008_21: mcp3008@1 { ++ compatible = "microchip,mcp3008"; ++ reg = <1>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@15 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3008_22: mcp3008@2 { ++ compatible = "microchip,mcp3008"; ++ reg = <2>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ spi0-0-present = <0>, "+0+8"; ++ spi0-1-present = <0>, "+1+9"; ++ spi1-0-present = <0>, "+2+10"; ++ spi1-1-present = <0>, "+3+11"; ++ spi1-2-present = <0>, "+4+12"; ++ spi2-0-present = <0>, "+5+13"; ++ spi2-1-present = <0>, "+6+14"; ++ spi2-2-present = <0>, "+7+15"; ++ spi0-0-speed = <&mcp3008_00>, "spi-max-frequency:0"; ++ spi0-1-speed = <&mcp3008_01>, "spi-max-frequency:0"; ++ spi1-0-speed = <&mcp3008_10>, "spi-max-frequency:0"; ++ spi1-1-speed = <&mcp3008_11>, "spi-max-frequency:0"; ++ spi1-2-speed = <&mcp3008_12>, "spi-max-frequency:0"; ++ spi2-0-speed = <&mcp3008_20>, "spi-max-frequency:0"; ++ spi2-1-speed = <&mcp3008_21>, "spi-max-frequency:0"; ++ spi2-2-speed = <&mcp3008_22>, "spi-max-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/mcp3202-overlay.dts b/arch/arm/boot/dts/overlays/mcp3202-overlay.dts +new file mode 100755 +index 000000000000..8e4e9f60f285 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mcp3202-overlay.dts +@@ -0,0 +1,205 @@ ++/* ++ * Device tree overlay for Microchip mcp3202 12-Bit A/D Converters ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spidev0>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev1>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "spi1/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path = "spi1/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@4 { ++ target-path = "spi1/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path = "spi2/spidev@0"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@6 { ++ target-path = "spi2/spidev@1"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@7 { ++ target-path = "spi2/spidev@2"; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@8 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3202_00: mcp3202@0 { ++ compatible = "mcp3202"; ++ reg = <0>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@9 { ++ target = <&spi0>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3202_01: mcp3202@1 { ++ compatible = "mcp3202"; ++ reg = <1>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@10 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3202_10: mcp3202@0 { ++ compatible = "mcp3202"; ++ reg = <0>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@11 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3202_11: mcp3202@1 { ++ compatible = "mcp3202"; ++ reg = <1>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@12 { ++ target = <&spi1>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3202_12: mcp3202@2 { ++ compatible = "mcp3202"; ++ reg = <2>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@13 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3202_20: mcp3202@0 { ++ compatible = "mcp3202"; ++ reg = <0>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@14 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3202_21: mcp3202@1 { ++ compatible = "mcp3202"; ++ reg = <1>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ fragment@15 { ++ target = <&spi2>; ++ __dormant__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mcp3202_22: mcp3202@2 { ++ compatible = "mcp3202"; ++ reg = <2>; ++ spi-max-frequency = <1600000>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ spi0-0-present = <0>, "+0+8"; ++ spi0-1-present = <0>, "+1+9"; ++ spi1-0-present = <0>, "+2+10"; ++ spi1-1-present = <0>, "+3+11"; ++ spi1-2-present = <0>, "+4+12"; ++ spi2-0-present = <0>, "+5+13"; ++ spi2-1-present = <0>, "+6+14"; ++ spi2-2-present = <0>, "+7+15"; ++ spi0-0-speed = <&mcp3202_00>, "spi-max-frequency:0"; ++ spi0-1-speed = <&mcp3202_01>, "spi-max-frequency:0"; ++ spi1-0-speed = <&mcp3202_10>, "spi-max-frequency:0"; ++ spi1-1-speed = <&mcp3202_11>, "spi-max-frequency:0"; ++ spi1-2-speed = <&mcp3202_12>, "spi-max-frequency:0"; ++ spi2-0-speed = <&mcp3202_20>, "spi-max-frequency:0"; ++ spi2-1-speed = <&mcp3202_21>, "spi-max-frequency:0"; ++ spi2-2-speed = <&mcp3202_22>, "spi-max-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/mcp342x-overlay.dts b/arch/arm/boot/dts/overlays/mcp342x-overlay.dts +new file mode 100644 +index 000000000000..714eca5a4b5e +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mcp342x-overlay.dts +@@ -0,0 +1,164 @@ ++// Overlay for MCP3421-8 ADCs from Microchip Semiconductor ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ mcp3421: mcp@68 { ++ reg = <0x68>; ++ compatible = "microchip,mcp3421"; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ mcp3422: mcp@68 { ++ reg = <0x68>; ++ compatible = "microchip,mcp3422"; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ mcp3423: mcp@68 { ++ reg = <0x68>; ++ compatible = "microchip,mcp3423"; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ mcp3424: mcp@68 { ++ reg = <0x68>; ++ compatible = "microchip,mcp3424"; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ mcp3425: mcp@68 { ++ reg = <0x68>; ++ compatible = "microchip,mcp3425","mcp3425"; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ mcp3426: mcp@68 { ++ reg = <0x68>; ++ compatible = "microchip,mcp3426"; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ mcp3427: mcp@68 { ++ reg = <0x68>; ++ compatible = "microchip,mcp3427"; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@7 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ mcp3428: mcp@68 { ++ reg = <0x68>; ++ compatible = "microchip,mcp3428"; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ addr = <&mcp3421>,"reg:0", ++ <&mcp3422>,"reg:0", ++ <&mcp3423>,"reg:0", ++ <&mcp3424>,"reg:0", ++ <&mcp3425>,"reg:0", ++ <&mcp3426>,"reg:0", ++ <&mcp3427>,"reg:0", ++ <&mcp3428>,"reg:0"; ++ mcp3421 = <0>,"=0"; ++ mcp3422 = <0>,"=1"; ++ mcp3423 = <0>,"=2"; ++ mcp3424 = <0>,"=3"; ++ mcp3425 = <0>,"=4"; ++ mcp3426 = <0>,"=5"; ++ mcp3427 = <0>,"=6"; ++ mcp3428 = <0>,"=7"; ++ }; ++}; ++ +diff --git a/arch/arm/boot/dts/overlays/media-center-overlay.dts b/arch/arm/boot/dts/overlays/media-center-overlay.dts +new file mode 100644 +index 000000000000..1b56963f4f16 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/media-center-overlay.dts +@@ -0,0 +1,134 @@ ++/* ++ * Device Tree overlay for Media Center HAT by Pi Supply ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ ++ spidev@0{ ++ status = "disabled"; ++ }; ++ ++ spidev@1{ ++ status = "disabled"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ rpi_display_pins: rpi_display_pins { ++ brcm,pins = <12 23 24 25>; ++ brcm,function = <1 1 1 0>; /* out out out in */ ++ brcm,pull = <0 0 0 2>; /* - - - up */ ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ rpidisplay: rpi-display@0{ ++ compatible = "ilitek,ili9341"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&rpi_display_pins>; ++ ++ spi-max-frequency = <32000000>; ++ rotate = <90>; ++ bgr; ++ fps = <30>; ++ buswidth = <8>; ++ reset-gpios = <&gpio 23 1>; ++ dc-gpios = <&gpio 24 0>; ++ led-gpios = <&gpio 12 0>; ++ debug = <0>; ++ }; ++ ++ rpidisplay_ts: rpi-display-ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <25 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 25 1>; ++ ti,x-plate-ohms = /bits/ 16 <60>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path = "/"; ++ __overlay__ { ++ lirc_rpi: lirc_rpi { ++ compatible = "rpi,lirc-rpi"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&lirc_pins>; ++ status = "okay"; ++ ++ // Override autodetection of IR receiver circuit ++ // (0 = active high, 1 = active low, -1 = no override ) ++ rpi,sense = <0xffffffff>; ++ ++ // Software carrier ++ // (0 = off, 1 = on) ++ rpi,softcarrier = <1>; ++ ++ // Invert output ++ // (0 = off, 1 = on) ++ rpi,invert = <0>; ++ ++ // Enable debugging messages ++ // (0 = off, 1 = on) ++ rpi,debug = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&gpio>; ++ __overlay__ { ++ lirc_pins: lirc_pins { ++ brcm,pins = <6 5>; ++ brcm,function = <1 0>; // out in ++ brcm,pull = <0 1>; // off down ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&rpidisplay>,"spi-max-frequency:0"; ++ rotate = <&rpidisplay>,"rotate:0"; ++ fps = <&rpidisplay>,"fps:0"; ++ debug = <&rpidisplay>,"debug:0", ++ <&lirc_rpi>,"rpi,debug:0"; ++ xohms = <&rpidisplay_ts>,"ti,x-plate-ohms;0"; ++ swapxy = <&rpidisplay_ts>,"ti,swap-xy?"; ++ backlight = <&rpidisplay>,"led-gpios:4", ++ <&rpi_display_pins>,"brcm,pins:0"; ++ ++ gpio_out_pin = <&lirc_pins>,"brcm,pins:0"; ++ gpio_in_pin = <&lirc_pins>,"brcm,pins:4"; ++ gpio_in_pull = <&lirc_pins>,"brcm,pull:4"; ++ ++ sense = <&lirc_rpi>,"rpi,sense:0"; ++ softcarrier = <&lirc_rpi>,"rpi,softcarrier:0"; ++ invert = <&lirc_rpi>,"rpi,invert:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/merus-amp-overlay.dts b/arch/arm/boot/dts/overlays/merus-amp-overlay.dts +new file mode 100644 +index 000000000000..4501fbdc253d +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/merus-amp-overlay.dts +@@ -0,0 +1,60 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Definitions for Infineon Merus-Amp ++/dts-v1/; ++/plugin/; ++#include ++#include ++ ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ merus_amp_pins: merus_amp_pins { ++ brcm,pins = <23>; ++ brcm,function = <0>; /* in */ ++ brcm,pull = <2>; /* up */ ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ merus_amp: ma120x0p@20 { ++ #sound-dai-cells = <0>; ++ compatible = "ma,ma120x0p"; ++ reg = <0x20>; ++ status = "okay"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&merus_amp_pins>; ++ enable_gp-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; ++ mute_gp-gpios = <&gpio 15 GPIO_ACTIVE_HIGH>; ++ booster_gp-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; ++ error_gp-gpios = <&gpio 23 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "merus,merus-amp"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/midi-uart0-overlay.dts b/arch/arm/boot/dts/overlays/midi-uart0-overlay.dts +new file mode 100644 +index 000000000000..f7e44d29e101 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/midi-uart0-overlay.dts +@@ -0,0 +1,36 @@ ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/* ++ * Fake a higher clock rate to get a larger divisor, and thereby a lower ++ * baudrate. The real clock is 48MHz, which we scale so that requesting ++ * 38.4kHz results in an actual 31.25kHz. ++ * ++ * 48000000*38400/31250 = 58982400 ++ */ ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ midi_clk: midi_clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-output-names = "uart0_pclk"; ++ clock-frequency = <58982400>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&uart0>; ++ __overlay__ { ++ clocks = <&midi_clk>, ++ <&clocks BCM2835_CLOCK_VPU>; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/midi-uart1-overlay.dts b/arch/arm/boot/dts/overlays/midi-uart1-overlay.dts +new file mode 100644 +index 000000000000..e0bc410acbff +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/midi-uart1-overlay.dts +@@ -0,0 +1,43 @@ ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/* ++ * Fake a higher clock rate to get a larger divisor, and thereby a lower ++ * baudrate. The real clock is 48MHz, which we scale so that requesting ++ * 38.4kHz results in an actual 31.25kHz. ++ * ++ * 48000000*38400/31250 = 58982400 ++ */ ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/clocks"; ++ __overlay__ { ++ midi_clk: clock@5 { ++ compatible = "fixed-factor-clock"; ++ #clock-cells = <0>; ++ clocks = <&aux BCM2835_AUX_CLOCK_UART>; ++ clock-mult = <38400>; ++ clock-div = <31250>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&uart1>; ++ __overlay__ { ++ clocks = <&midi_clk>; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ clock-output-names = "aux_uart", "aux_spi1", "aux_spi2"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/miniuart-bt-overlay.dts b/arch/arm/boot/dts/overlays/miniuart-bt-overlay.dts +new file mode 100644 +index 000000000000..da49f14a0940 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/miniuart-bt-overlay.dts +@@ -0,0 +1,93 @@ ++/dts-v1/; ++/plugin/; ++ ++/* Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore ++ UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum ++ usable baudrate. ++ ++ It is also necessary to edit /lib/systemd/system/hciuart.service and ++ replace ttyAMA0 with ttyS0, unless you have a system with udev rules ++ that create /dev/serial0 and /dev/serial1, in which case use /dev/serial1 ++ instead because it will always be correct. ++ ++ If cmdline.txt uses the alias serial0 to refer to the user-accessable port ++ then the firmware will replace with the appropriate port whether or not ++ this overlay is used. ++*/ ++ ++#include ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&uart0>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&bt>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&uart1>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart1_pins &bt_pins &fake_bt_cts>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&uart0_pins>; ++ __overlay__ { ++ brcm,pins; ++ brcm,function; ++ brcm,pull; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&uart1_pins>; ++ __overlay__ { ++ brcm,pins = <32 33>; ++ brcm,function = <2>; /* alt5=UART1 */ ++ brcm,pull = <0 2>; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&gpio>; ++ __overlay__ { ++ fake_bt_cts: fake_bt_cts { ++ brcm,pins = <31>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@6 { ++ target-path = "/aliases"; ++ __overlay__ { ++ serial0 = "/soc/serial@7e201000"; ++ serial1 = "/soc/serial@7e215040"; ++ }; ++ }; ++ ++ fragment@7 { ++ target = <&minibt>; ++ minibt_frag: __overlay__ { ++ }; ++ }; ++ ++ __overrides__ { ++ krnbt = <&minibt_frag>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/mmc-overlay.dts b/arch/arm/boot/dts/overlays/mmc-overlay.dts +new file mode 100644 +index 000000000000..c1a2f691aa1e +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mmc-overlay.dts +@@ -0,0 +1,46 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&mmc>; ++ frag0: __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&mmc_pins>; ++ bus-width = <4>; ++ brcm,overclock-50 = <0>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ mmc_pins: mmc_pins { ++ brcm,pins = <48 49 50 51 52 53>; ++ brcm,function = <7>; /* alt3 */ ++ brcm,pull = <0 2 2 2 2 2>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sdhost>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&mmcnr>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ __overrides__ { ++ overclock_50 = <&frag0>,"brcm,overclock-50:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/mpu6050-overlay.dts b/arch/arm/boot/dts/overlays/mpu6050-overlay.dts +new file mode 100644 +index 000000000000..3109d90562ae +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mpu6050-overlay.dts +@@ -0,0 +1,28 @@ ++// Definitions for MPU6050 ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ clock-frequency = <400000>; ++ ++ mpu6050: mpu6050@68 { ++ compatible = "invensense,mpu6050"; ++ reg = <0x68>; ++ interrupt-parent = <&gpio>; ++ interrupts = <4 1>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ interrupt = <&mpu6050>,"interrupts:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/mz61581-overlay.dts b/arch/arm/boot/dts/overlays/mz61581-overlay.dts +new file mode 100644 +index 000000000000..6e00e8b2ddf2 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/mz61581-overlay.dts +@@ -0,0 +1,117 @@ ++/* ++ * Device Tree overlay for MZ61581-PI-EXT 2014.12.28 by Tontec ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ mz61581_pins: mz61581_pins { ++ brcm,pins = <4 15 18 25>; ++ brcm,function = <0 1 1 1>; /* in out out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ mz61581: mz61581@0{ ++ compatible = "samsung,s6d02a1"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&mz61581_pins>; ++ ++ spi-max-frequency = <128000000>; ++ spi-cpol; ++ spi-cpha; ++ ++ width = <320>; ++ height = <480>; ++ rotate = <270>; ++ bgr; ++ fps = <30>; ++ buswidth = <8>; ++ txbuflen = <32768>; ++ ++ reset-gpios = <&gpio 15 1>; ++ dc-gpios = <&gpio 25 0>; ++ led-gpios = <&gpio 18 0>; ++ ++ init = <0x10000b0 00 ++ 0x1000011 ++ 0x20000ff ++ 0x10000b3 0x02 0x00 0x00 0x00 ++ 0x10000c0 0x13 0x3b 0x00 0x02 0x00 0x01 0x00 0x43 ++ 0x10000c1 0x08 0x16 0x08 0x08 ++ 0x10000c4 0x11 0x07 0x03 0x03 ++ 0x10000c6 0x00 ++ 0x10000c8 0x03 0x03 0x13 0x5c 0x03 0x07 0x14 0x08 0x00 0x21 0x08 0x14 0x07 0x53 0x0c 0x13 0x03 0x03 0x21 0x00 ++ 0x1000035 0x00 ++ 0x1000036 0xa0 ++ 0x100003a 0x55 ++ 0x1000044 0x00 0x01 ++ 0x10000d0 0x07 0x07 0x1d 0x03 ++ 0x10000d1 0x03 0x30 0x10 ++ 0x10000d2 0x03 0x14 0x04 ++ 0x1000029 ++ 0x100002c>; ++ ++ /* This is a workaround to make sure the init sequence slows down and doesn't fail */ ++ debug = <3>; ++ }; ++ ++ mz61581_ts: mz61581_ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <4 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 4 0>; ++ ++ ti,x-plate-ohms = /bits/ 16 <60>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ speed = <&mz61581>, "spi-max-frequency:0"; ++ rotate = <&mz61581>, "rotate:0"; ++ fps = <&mz61581>, "fps:0"; ++ txbuflen = <&mz61581>, "txbuflen:0"; ++ debug = <&mz61581>, "debug:0"; ++ xohms = <&mz61581_ts>,"ti,x-plate-ohms;0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/ov5647-overlay.dts b/arch/arm/boot/dts/overlays/ov5647-overlay.dts +new file mode 100644 +index 000000000000..fd1e7a457f69 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ov5647-overlay.dts +@@ -0,0 +1,92 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Definitions for OV5647 camera module on VC I2C bus ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_csi_dsi>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ov5647: ov5647@36 { ++ compatible = "ovti,ov5647"; ++ reg = <0x36>; ++ status = "okay"; ++ ++ pwdn-gpios = <&gpio 41 1>, <&gpio 32 1>; ++ clocks = <&ov5647_clk>; ++ ++ rotation = <0>; ++ ++ port { ++ ov5647_0: endpoint { ++ remote-endpoint = <&csi1_ep>; ++ clock-lanes = <0>; ++ data-lanes = <1 2>; ++ clock-noncontinuous; ++ link-frequencies = ++ /bits/ 64 <297000000>; ++ }; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&csi1>; ++ __overlay__ { ++ status = "okay"; ++ ++ port { ++ csi1_ep: endpoint { ++ remote-endpoint = <&ov5647_0>; ++ data-lanes = <1 2>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c0if>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&i2c0mux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@4 { ++ target-path="/__overrides__"; ++ __overlay__ { ++ cam0-pwdn-ctrl = <&ov5647>,"pwdn-gpios:0"; ++ cam0-pwdn = <&ov5647>,"pwdn-gpios:4"; ++ cam0-led-ctrl = <&ov5647>,"pwdn-gpios:12"; ++ cam0-led = <&ov5647>,"pwdn-gpios:16"; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path = "/"; ++ __overlay__ { ++ ov5647_clk: camera-clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <25000000>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ rotation = <&ov5647>,"rotation:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/ov7251-overlay.dts b/arch/arm/boot/dts/overlays/ov7251-overlay.dts +new file mode 100644 +index 000000000000..f04eafd4adf9 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ov7251-overlay.dts +@@ -0,0 +1,111 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Definitions for OV7251 camera module on VC I2C bus ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_csi_dsi>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ov7251: ov7251@60 { ++ compatible = "ovti,ov7251"; ++ reg = <0x60>; ++ status = "okay"; ++ ++ clocks = <&ov7251_clk>; ++ clock-names = "xclk"; ++ clock-frequency = <24000000>; ++ ++ vdddo-supply = <&ov7251_dovdd>; ++ vdda-supply = <&ov7251_avdd>; ++ vddd-supply = <&ov7251_dvdd>; ++ ++ enable-gpios = <&gpio 41 GPIO_ACTIVE_HIGH>; ++ ++ port { ++ ov7251_0: endpoint { ++ remote-endpoint = <&csi1_ep>; ++ clock-lanes = <0>; ++ data-lanes = <1>; ++ clock-noncontinuous; ++ link-frequencies = ++ /bits/ 64 <456000000>; ++ }; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&csi1>; ++ __overlay__ { ++ status = "okay"; ++ ++ port { ++ csi1_ep: endpoint { ++ remote-endpoint = <&ov7251_0>; ++ data-lanes = <1>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c0if>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path="/"; ++ __overlay__ { ++ ov7251_avdd: fixedregulator@0 { ++ compatible = "regulator-fixed"; ++ regulator-name = "ov7251_avdd"; ++ regulator-min-microvolt = <2800000>; ++ regulator-max-microvolt = <2800000>; ++ }; ++ ov7251_dovdd: fixedregulator@1 { ++ compatible = "regulator-fixed"; ++ regulator-name = "ov7251_dovdd"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ }; ++ ov7251_dvdd: fixedregulator@2 { ++ compatible = "regulator-fixed"; ++ regulator-name = "ov7251_dvdd"; ++ regulator-min-microvolt = <1200000>; ++ regulator-max-microvolt = <1200000>; ++ }; ++ ov7251_clk: ov7251-clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <24000000>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c0mux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path="/__overrides__"; ++ __overlay__ { ++ cam0-pwdn-ctrl = <&ov7251>,"enable-gpios:0"; ++ cam0-pwdn = <&ov7251>,"enable-gpios:4"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/ov9281-overlay.dts b/arch/arm/boot/dts/overlays/ov9281-overlay.dts +new file mode 100644 +index 000000000000..40b298d3dd86 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ov9281-overlay.dts +@@ -0,0 +1,111 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Definitions for OV9281 camera module on VC I2C bus ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_csi_dsi>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ov9281: ov9281@60 { ++ compatible = "ovti,ov9281"; ++ reg = <0x60>; ++ status = "okay"; ++ ++ clocks = <&ov9281_clk>; ++ clock-names = "xvclk"; ++ ++ avdd-supply = <&ov9281_avdd>; ++ dovdd-supply = <&ov9281_dovdd>; ++ dvdd-supply = <&ov9281_dvdd>; ++ ++ port { ++ ov9281_0: endpoint { ++ remote-endpoint = <&csi1_ep>; ++ clock-lanes = <0>; ++ data-lanes = <1 2>; ++ clock-noncontinuous; ++ link-frequencies = ++ /bits/ 64 <400000000>; ++ }; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&csi1>; ++ __overlay__ { ++ status = "okay"; ++ ++ port { ++ csi1_ep: endpoint { ++ remote-endpoint = <&ov9281_0>; ++ data-lanes = <1 2>; ++ clock-noncontinuous; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c0if>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path="/"; ++ __overlay__ { ++ ov9281_avdd: fixedregulator@0 { ++ compatible = "regulator-fixed"; ++ regulator-name = "ov9281_avdd"; ++ regulator-min-microvolt = <2800000>; ++ regulator-max-microvolt = <2800000>; ++ gpio = <&gpio 41 GPIO_ACTIVE_HIGH>; ++ enable-active-high; ++ }; ++ ov9281_dovdd: fixedregulator@1 { ++ compatible = "regulator-fixed"; ++ regulator-name = "ov9281_dovdd"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ }; ++ ov9281_dvdd: fixedregulator@2 { ++ compatible = "regulator-fixed"; ++ regulator-name = "ov9281_dvdd"; ++ regulator-min-microvolt = <1200000>; ++ regulator-max-microvolt = <1200000>; ++ }; ++ ov9281_clk: ov9281-clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <24000000>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c0mux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path="/__overrides__"; ++ __overlay__ { ++ cam0-pwdn-ctrl = <&ov9281_avdd>,"gpio:0"; ++ cam0-pwdn = <&ov9281_avdd>,"gpio:4"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/overlay_map.dts b/arch/arm/boot/dts/overlays/overlay_map.dts +new file mode 100644 +index 000000000000..22b0ad1738ec +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/overlay_map.dts +@@ -0,0 +1,141 @@ ++/dts-v1/; ++ ++/ { ++ bmp085_i2c-sensor { ++ deprecated = "use i2c-sensor,bmp085"; ++ }; ++ ++ highperi { ++ bcm2711; ++ }; ++ ++ i2c0-bcm2708 { ++ deprecated = "use i2c0"; ++ }; ++ ++ i2c1-bcm2708 { ++ deprecated = "use i2c1"; ++ }; ++ ++ i2c3 { ++ bcm2711; ++ }; ++ ++ i2c4 { ++ bcm2711; ++ }; ++ ++ i2c5 { ++ bcm2711; ++ }; ++ ++ i2c6 { ++ bcm2711; ++ }; ++ ++ lirc-rpi { ++ deprecated = "use gpio-ir"; ++ }; ++ ++ pi3-act-led { ++ renamed = "act-led"; ++ }; ++ ++ pi3-disable-bt { ++ renamed = "disable-bt"; ++ }; ++ ++ pi3-disable-wifi { ++ renamed = "disable-wifi"; ++ }; ++ ++ pi3-miniuart-bt { ++ renamed = "miniuart-bt"; ++ }; ++ ++ rpivid-v4l2 { ++ bcm2711; ++ }; ++ ++ sdio-1bit { ++ deprecated = "use sdio,bus_width=1,gpios_22_25"; ++ }; ++ ++ spi0-cs { ++ renamed = "spi0-2cs"; ++ }; ++ ++ spi0-hw-cs { ++ deprecated = "no longer necessary"; ++ }; ++ ++ spi3-1cs { ++ bcm2711; ++ }; ++ ++ spi3-2cs { ++ bcm2711; ++ }; ++ ++ spi4-1cs { ++ bcm2711; ++ }; ++ ++ spi4-2cs { ++ bcm2711; ++ }; ++ ++ spi5-1cs { ++ bcm2711; ++ }; ++ ++ spi5-2cs { ++ bcm2711; ++ }; ++ ++ spi6-1cs { ++ bcm2711; ++ }; ++ ++ spi6-2cs { ++ bcm2711; ++ }; ++ ++ uart2 { ++ bcm2711; ++ }; ++ ++ uart3 { ++ bcm2711; ++ }; ++ ++ uart4 { ++ bcm2711; ++ }; ++ ++ uart5 { ++ bcm2711; ++ }; ++ ++ upstream { ++ bcm2835; ++ bcm2711 = "upstream-pi4"; ++ }; ++ ++ upstream-aux-interrupt { ++ deprecated = "no longer necessary"; ++ }; ++ ++ upstream-pi4 { ++ bcm2711; ++ }; ++ ++ vc4-kms-v3d { ++ bcm2835; ++ bcm2711 = "vc4-kms-v3d-pi4"; ++ }; ++ ++ vc4-kms-v3d-pi4 { ++ bcm2711; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/papirus-overlay.dts b/arch/arm/boot/dts/overlays/papirus-overlay.dts +new file mode 100644 +index 000000000000..7b6bcfd49c86 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/papirus-overlay.dts +@@ -0,0 +1,89 @@ ++/* PaPiRus ePaper Screen by Pi Supply */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ display_temp: lm75@48 { ++ compatible = "lm75b"; ++ reg = <0x48>; ++ status = "okay"; ++ #thermal-sensor-cells = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ thermal-zones { ++ display { ++ polling-delay-passive = <0>; ++ polling-delay = <0>; ++ thermal-sensors = <&display_temp>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ ++ spidev@0{ ++ status = "disabled"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ repaper_pins: repaper_pins { ++ brcm,pins = <14 15 23 24 25>; ++ brcm,function = <1 1 1 1 0>; /* out out out out in */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ repaper: repaper@0{ ++ compatible = "not_set"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&repaper_pins>; ++ ++ spi-max-frequency = <8000000>; ++ ++ panel-on-gpios = <&gpio 23 0>; ++ border-gpios = <&gpio 14 0>; ++ discharge-gpios = <&gpio 15 0>; ++ reset-gpios = <&gpio 24 0>; ++ busy-gpios = <&gpio 25 0>; ++ ++ repaper-thermal-zone = "display"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ panel = <&repaper>, "compatible"; ++ speed = <&repaper>, "spi-max-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/pca953x-overlay.dts b/arch/arm/boot/dts/overlays/pca953x-overlay.dts +new file mode 100644 +index 000000000000..8b6ee44665ce +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pca953x-overlay.dts +@@ -0,0 +1,240 @@ ++// Definitions for NXP PCA953x family of I2C GPIO controllers on ARM I2C bus. ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ pca: pca@20 { ++ compatible = "nxp,pca9534"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca6416"; ++ }; ++ }; ++ fragment@2 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca9505"; ++ }; ++ }; ++ fragment@3 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca9535"; ++ }; ++ }; ++ fragment@4 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca9536"; ++ }; ++ }; ++ fragment@5 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca9537"; ++ }; ++ }; ++ fragment@6 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca9538"; ++ }; ++ }; ++ fragment@7 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca9539"; ++ }; ++ }; ++ fragment@8 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca9554"; ++ }; ++ }; ++ fragment@9 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca9555"; ++ }; ++ }; ++ fragment@10 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca9556"; ++ }; ++ }; ++ fragment@11 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca9557"; ++ }; ++ }; ++ fragment@12 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca9574"; ++ }; ++ }; ++ fragment@13 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca9575"; ++ }; ++ }; ++ fragment@14 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca9698"; ++ }; ++ }; ++ fragment@15 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca16416"; ++ }; ++ }; ++ fragment@16 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca16524"; ++ }; ++ }; ++ fragment@17 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "nxp,pca19555a"; ++ }; ++ }; ++ fragment@18 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "maxim,max7310"; ++ }; ++ }; ++ fragment@19 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "maxim,max7312"; ++ }; ++ }; ++ fragment@20 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "maxim,max7313"; ++ }; ++ }; ++ fragment@21 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "maxim,max7315"; ++ }; ++ }; ++ fragment@22 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "ti,pca6107"; ++ }; ++ }; ++ fragment@23 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "ti,tca6408"; ++ }; ++ }; ++ fragment@24 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "ti,tca6416"; ++ }; ++ }; ++ fragment@25 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "ti,tca6424"; ++ }; ++ }; ++ fragment@26 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "ti,tca9539"; ++ }; ++ }; ++ fragment@27 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "ti,tca9554"; ++ }; ++ }; ++ fragment@28 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "onnn,cat9554"; ++ }; ++ }; ++ fragment@29 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "onnn,pca9654"; ++ }; ++ }; ++ fragment@30 { ++ target = <&pca>; ++ __dormant__ { ++ compatible = "exar,xra1202"; ++ }; ++ }; ++ ++ __overrides__ { ++ addr = <&pca>,"reg:0"; ++ pca6416 = <0>, "+1"; ++ pca9505 = <0>, "+2"; ++ pca9535 = <0>, "+3"; ++ pca9536 = <0>, "+4"; ++ pca9537 = <0>, "+5"; ++ pca9538 = <0>, "+6"; ++ pca9539 = <0>, "+7"; ++ pca9554 = <0>, "+8"; ++ pca9555 = <0>, "+9"; ++ pca9556 = <0>, "+10"; ++ pca9557 = <0>, "+11"; ++ pca9574 = <0>, "+12"; ++ pca9575 = <0>, "+13"; ++ pca9698 = <0>, "+14"; ++ pca16416 = <0>, "+15"; ++ pca16524 = <0>, "+16"; ++ pca19555a = <0>, "+17"; ++ max7310 = <0>, "+18"; ++ max7312 = <0>, "+19"; ++ max7313 = <0>, "+20"; ++ max7315 = <0>, "+21"; ++ pca6107 = <0>, "+22"; ++ tca6408 = <0>, "+23"; ++ tca6416 = <0>, "+24"; ++ tca6424 = <0>, "+25"; ++ tca9539 = <0>, "+26"; ++ tca9554 = <0>, "+27"; ++ cat9554 = <0>, "+28"; ++ pca9654 = <0>, "+29"; ++ xra1202 = <0>, "+30"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/pibell-overlay.dts b/arch/arm/boot/dts/overlays/pibell-overlay.dts +new file mode 100644 +index 000000000000..9333a9b09772 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pibell-overlay.dts +@@ -0,0 +1,81 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ codec_out: spdif-transmitter { ++ #address-cells = <0>; ++ #size-cells = <0>; ++ #sound-dai-cells = <0>; ++ compatible = "linux,spdif-dit"; ++ status = "okay"; ++ }; ++ ++ codec_in: card-codec { ++ #sound-dai-cells = <0>; ++ compatible = "invensense,ics43432"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2s>; ++ __overlay__ { ++ #sound-dai-cells = <0>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ snd: __overlay__ { ++ compatible = "simple-audio-card"; ++ simple-audio-card,name = "PiBell"; ++ ++ status="okay"; ++ ++ capture_link: simple-audio-card,dai-link@0 { ++ format = "i2s"; ++ ++ r_cpu_dai: cpu { ++ sound-dai = <&i2s>; ++ ++/* example TDM slot configuration ++ dai-tdm-slot-num = <2>; ++ dai-tdm-slot-width = <32>; ++*/ ++ }; ++ ++ r_codec_dai: codec { ++ sound-dai = <&codec_in>; ++ }; ++ }; ++ ++ playback_link: simple-audio-card,dai-link@1 { ++ format = "i2s"; ++ ++ p_cpu_dai: cpu { ++ sound-dai = <&i2s>; ++ ++/* example TDM slot configuration ++ dai-tdm-slot-num = <2>; ++ dai-tdm-slot-width = <32>; ++*/ ++ }; ++ ++ p_codec_dai: codec { ++ sound-dai = <&codec_out>; ++ }; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ alsaname = <&snd>, "simple-audio-card,name"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/pifacedigital-overlay.dts b/arch/arm/boot/dts/overlays/pifacedigital-overlay.dts +new file mode 100644 +index 000000000000..532a858683d6 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pifacedigital-overlay.dts +@@ -0,0 +1,144 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++/* ++ * PiFace Digital, Device Tree Overlay. ++ * Copyright (C) 2020 Thomas Preston ++ * ++ * The PiFace Digital is a convenient breakout board for the Microchip mcp23s17 ++ * SPI GPIO port expander. ++ * ++ * The first eight GPIOs 0..7 (bank A) are connected to eight output terminals ++ * and LEDs, plus two relays on the first two outputs. These output loads are ++ * active-high. ++ * ++ * The next eight GPIOs 8..15 (bank B) are connected to eight input terminals ++ * with four on-board switches connecting them to ground. Inputs devices are ++ * therefore expected to bridge terminals to ground, so the mcp23s17 pullups are ++ * activated for GPIO bank B. ++ * ++ * On PiFace Digital, the mcp23s17 is connected to the Raspberry Pi's SPI0 CS0 ++ * bus. Each SPI bus supports up to eight addressable child devices. The PiFace ++ * Digital only supports addresses 0-4, which can be configured by jumpers JP1 ++ * and JP2. ++ * ++ * You can tell the driver about these jumper configurations with the ++ * spi-present-mask bitmask: ++ * ++ * | JP1 | JP2 | dtoverlay line in /boot/config.txt | ++ * | --- | --- | ------------------------------------------ | ++ * | 0 | 0 | dtoverlay=pifacedigital | ++ * | 0 | 0 | dtoverlay=pifacedigital:spi-present-mask=1 | ++ * | 0 | 1 | dtoverlay=pifacedigital:spi-present-mask=2 | ++ * | 1 | 0 | dtoverlay=pifacedigital:spi-present-mask=4 | ++ * | 1 | 1 | dtoverlay=pifacedigital:spi-present-mask=8 | ++ * ++ * # Example ++ * Set the dtoverlay config in /boot/config.txt and power off the Raspberry Pi: ++ * ++ * $ grep pifacedigital /boot/config.txt ++ * dtoverlay=pifacedigital ++ * $ sudo systemctl poweroff ++ * ++ * Attach the PiFace Digital and power on the Raspberry Pi. ++ * Then use the libgpiod tools to query the device: ++ * ++ * $ sudo apt install gpiod ++ * $ gpiodetect | grep mcp23s17 ++ * gpiochip2 [mcp23s17.0] (16 lines) ++ * ++ * Set GPIO outputs 0, 2 and 5: ++ * ++ * $ gpioset gpiochip2 0=1 2=1 5=1 ++ * ++ * Get GPIO status (input GPIO 8..15 are high, because they are active-low): ++ * ++ * $ gpioget gpiochip2 {8..15} ++ * 1 1 1 1 1 1 1 1 ++ * ++ * And even monitor interrupts: ++ * ++ * $ gpiomon gpiochip2 {8..15} ++ * event: FALLING EDGE offset: 11 timestamp: [1597361662.926741667] ++ * event: RISING EDGE offset: 11 timestamp: [1597361663.062555051] ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ /* Disable exposing /dev/spidev0.0 */ ++ fragment@0 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ /* Add the PiFace Digital device node to the spi0.0 device. */ ++ fragment@1 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pfdigital: pifacedigital@0 { ++ compatible = "microchip,mcp23s17"; ++ reg = <0>; ++ ++ /* Set devices present with 8-bit mask. */ ++ microchip,spi-present-mask = <0x01>; ++ spi-max-frequency = <500000>; ++ ++ gpio-controller; ++ #gpio-cells = <2>; ++ ++ /* This device can pass through interrupts. */ ++ interrupt-controller; ++ #interrupt-cells = <2>; ++ ++ /* INTB is connected to GPIO 25. ++ * 0x8 active-low level-sensitive ++ */ ++ interrupts = <25 0x8>; ++ interrupt-parent = <&gpio>; ++ ++ /* Configure pull-ups on bank B GPIOs */ ++ pinctrl-0 = <&pfdigital_irq &pfdigital_pullups>; ++ pinctrl-names = "default"; ++ pfdigital_pullups: pinmux { ++ pins = ++ "gpio8", ++ "gpio9", ++ "gpio10", ++ "gpio11", ++ "gpio12", ++ "gpio13", ++ "gpio14", ++ "gpio15"; ++ bias-pull-up; ++ }; ++ }; ++ }; ++ }; ++ ++ /* PiFace Digital mcp23s17 INTB pin is connected to GPIO 25. The INTB ++ * pin is configured active-low (0 on interrupt), so expect to see ++ * FALLING_EDGE when inputs are bridged to ground (switch is pressed). ++ */ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ pfdigital_irq: pifacedigital_irq { ++ brcm,pins = <25>; ++ brcm,function = <0>; /* input */ ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ spi-present-mask = <&pfdigital>, "microchip,spi-present-mask:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/piglow-overlay.dts b/arch/arm/boot/dts/overlays/piglow-overlay.dts +new file mode 100644 +index 000000000000..075bceef158c +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/piglow-overlay.dts +@@ -0,0 +1,97 @@ ++// Definitions for SN3218 LED driver from Si-En Technology on PiGlow ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ sn3218@54 { ++ compatible = "si-en,sn3218"; ++ reg = <0x54>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ led@1 { ++ reg = <1>; ++ label = "piglow:red:led1"; ++ }; ++ led@2 { ++ reg = <2>; ++ label = "piglow:orange:led2"; ++ }; ++ led@3 { ++ reg = <3>; ++ label = "piglow:yellow:led3"; ++ }; ++ led@4 { ++ reg = <4>; ++ label = "piglow:green:led4"; ++ }; ++ led@5 { ++ reg = <5>; ++ label = "piglow:blue:led5"; ++ }; ++ led@6 { ++ reg = <6>; ++ label = "piglow:green:led6"; ++ }; ++ led@7 { ++ reg = <7>; ++ label = "piglow:red:led7"; ++ }; ++ led@8 { ++ reg = <8>; ++ label = "piglow:orange:led8"; ++ }; ++ led@9 { ++ reg = <9>; ++ label = "piglow:yellow:led9"; ++ }; ++ led@10 { ++ reg = <10>; ++ label = "piglow:white:led10"; ++ }; ++ led@11 { ++ reg = <11>; ++ label = "piglow:white:led11"; ++ }; ++ led@12 { ++ reg = <12>; ++ label = "piglow:blue:led12"; ++ }; ++ led@13 { ++ reg = <13>; ++ label = "piglow:white:led13"; ++ }; ++ led@14 { ++ reg = <14>; ++ label = "piglow:green:led14"; ++ }; ++ led@15 { ++ reg = <15>; ++ label = "piglow:blue:led15"; ++ }; ++ led@16 { ++ reg = <16>; ++ label = "piglow:yellow:led16"; ++ }; ++ led@17 { ++ reg = <17>; ++ label = "piglow:orange:led17"; ++ }; ++ led@18 { ++ reg = <18>; ++ label = "piglow:red:led18"; ++ }; ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/piscreen-overlay.dts b/arch/arm/boot/dts/overlays/piscreen-overlay.dts +new file mode 100644 +index 000000000000..1ac75a248fab +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/piscreen-overlay.dts +@@ -0,0 +1,102 @@ ++/* ++ * Device Tree overlay for PiScreen 3.5" display shield by Ozzmaker ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ piscreen_pins: piscreen_pins { ++ brcm,pins = <17 25 24 22>; ++ brcm,function = <0 1 1 1>; /* in out out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ piscreen: piscreen@0{ ++ compatible = "ilitek,ili9486"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&piscreen_pins>; ++ ++ spi-max-frequency = <24000000>; ++ rotate = <270>; ++ bgr; ++ fps = <30>; ++ buswidth = <8>; ++ regwidth = <16>; ++ reset-gpios = <&gpio 25 1>; ++ dc-gpios = <&gpio 24 0>; ++ led-gpios = <&gpio 22 0>; ++ debug = <0>; ++ ++ init = <0x10000b0 0x00 ++ 0x1000011 ++ 0x20000ff ++ 0x100003a 0x55 ++ 0x1000036 0x28 ++ 0x10000c2 0x44 ++ 0x10000c5 0x00 0x00 0x00 0x00 ++ 0x10000e0 0x0f 0x1f 0x1c 0x0c 0x0f 0x08 0x48 0x98 0x37 0x0a 0x13 0x04 0x11 0x0d 0x00 ++ 0x10000e1 0x0f 0x32 0x2e 0x0b 0x0d 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00 ++ 0x10000e2 0x0f 0x32 0x2e 0x0b 0x0d 0x05 0x47 0x75 0x37 0x06 0x10 0x03 0x24 0x20 0x00 ++ 0x1000011 ++ 0x1000029>; ++ }; ++ ++ piscreen_ts: piscreen-ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <17 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 17 0>; ++ ti,swap-xy; ++ ti,x-plate-ohms = /bits/ 16 <100>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ speed = <&piscreen>,"spi-max-frequency:0"; ++ rotate = <&piscreen>,"rotate:0"; ++ fps = <&piscreen>,"fps:0"; ++ debug = <&piscreen>,"debug:0"; ++ xohms = <&piscreen_ts>,"ti,x-plate-ohms;0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/piscreen2r-overlay.dts b/arch/arm/boot/dts/overlays/piscreen2r-overlay.dts +new file mode 100644 +index 000000000000..9d2b51101969 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/piscreen2r-overlay.dts +@@ -0,0 +1,106 @@ ++ /* ++ * Device Tree overlay for PiScreen2 3.5" TFT with resistive touch by Ozzmaker.com ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ piscreen2_pins: piscreen2_pins { ++ brcm,pins = <17 25 24 22>; ++ brcm,function = <0 1 1 1>; /* in out out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ piscreen2: piscreen2@0{ ++ compatible = "ilitek,ili9486"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&piscreen2_pins>; ++ bgr; ++ spi-max-frequency = <64000000>; ++ rotate = <90>; ++ fps = <30>; ++ buswidth = <8>; ++ regwidth = <16>; ++ txbuflen = <32768>; ++ reset-gpios = <&gpio 25 1>; ++ dc-gpios = <&gpio 24 0>; ++ led-gpios = <&gpio 22 0>; ++ debug = <0>; ++ ++ init = <0x10000b0 0x00 ++ 0x1000011 ++ 0x20000ff ++ 0x100003a 0x55 ++ 0x1000036 0x28 ++ 0x10000c0 0x11 0x09 ++ 0x10000c1 0x41 ++ 0x10000c5 0x00 0x00 0x00 0x00 ++ 0x10000b6 0x00 0x02 ++ 0x10000f7 0xa9 0x51 0x2c 0x2 ++ 0x10000be 0x00 0x04 ++ 0x10000e9 0x00 ++ 0x1000011 ++ 0x1000029>; ++ ++ }; ++ ++ piscreen2_ts: piscreen2-ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <17 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 17 0>; ++ ti,swap-xy; ++ ti,x-plate-ohms = /bits/ 16 <100>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ speed = <&piscreen2>,"spi-max-frequency:0"; ++ rotate = <&piscreen2>,"rotate:0"; ++ fps = <&piscreen2>,"fps:0"; ++ debug = <&piscreen2>,"debug:0"; ++ xohms = <&piscreen2_ts>,"ti,x-plate-ohms;0"; ++ }; ++}; ++ +diff --git a/arch/arm/boot/dts/overlays/pisound-overlay.dts b/arch/arm/boot/dts/overlays/pisound-overlay.dts +new file mode 100644 +index 000000000000..49efb2b768fb +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pisound-overlay.dts +@@ -0,0 +1,120 @@ ++/* ++ * Pisound Linux kernel module. ++ * Copyright (C) 2016-2017 Vilniaus Blokas UAB, https://blokas.io/pisound ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * as published by the Free Software Foundation; version 2 of the ++ * License. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&spi0>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pisound_spi: pisound_spi@0{ ++ compatible = "blokaslabs,pisound-spi"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi0_pins>; ++ spi-max-frequency = <1000000>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target-path = "/"; ++ __overlay__ { ++ pcm5102a-codec { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm5102a"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "blokaslabs,pisound"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ ++ pinctrl-0 = <&pisound_button_pins>; ++ ++ osr-gpios = ++ <&gpio 13 GPIO_ACTIVE_HIGH>, ++ <&gpio 26 GPIO_ACTIVE_HIGH>, ++ <&gpio 16 GPIO_ACTIVE_HIGH>; ++ ++ reset-gpios = ++ <&gpio 12 GPIO_ACTIVE_HIGH>, ++ <&gpio 24 GPIO_ACTIVE_HIGH>; ++ ++ data_available-gpios = <&gpio 25 GPIO_ACTIVE_HIGH>; ++ ++ button-gpios = <&gpio 17 GPIO_ACTIVE_LOW>; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&gpio>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pisound_button_pins>; ++ ++ pisound_button_pins: pisound_button_pins { ++ brcm,pins = <17>; ++ brcm,function = <0>; // Input ++ brcm,pull = <2>; // Pull-Up ++ }; ++ }; ++ }; ++ ++ fragment@7 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/pitft22-overlay.dts b/arch/arm/boot/dts/overlays/pitft22-overlay.dts +new file mode 100644 +index 000000000000..589ad13795b1 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pitft22-overlay.dts +@@ -0,0 +1,69 @@ ++/* ++ * Device Tree overlay for pitft by Adafruit ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ ++ spidev@0{ ++ status = "disabled"; ++ }; ++ ++ spidev@1{ ++ status = "disabled"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ pitft_pins: pitft_pins { ++ brcm,pins = <25>; ++ brcm,function = <1>; /* out */ ++ brcm,pull = <0>; /* none */ ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pitft: pitft@0{ ++ compatible = "ilitek,ili9340"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pitft_pins>; ++ ++ spi-max-frequency = <32000000>; ++ rotate = <90>; ++ fps = <25>; ++ bgr; ++ buswidth = <8>; ++ dc-gpios = <&gpio 25 0>; ++ debug = <0>; ++ }; ++ ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&pitft>,"spi-max-frequency:0"; ++ rotate = <&pitft>,"rotate:0"; ++ fps = <&pitft>,"fps:0"; ++ debug = <&pitft>,"debug:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/pitft28-capacitive-overlay.dts b/arch/arm/boot/dts/overlays/pitft28-capacitive-overlay.dts +new file mode 100644 +index 000000000000..33901ee1db7a +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pitft28-capacitive-overlay.dts +@@ -0,0 +1,91 @@ ++/* ++ * Device Tree overlay for Adafruit PiTFT 2.8" capacitive touch screen ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ pitft_pins: pitft_pins { ++ brcm,pins = <24 25>; ++ brcm,function = <0 1>; /* in out */ ++ brcm,pull = <2 0>; /* pullup none */ ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pitft: pitft@0{ ++ compatible = "ilitek,ili9340"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pitft_pins>; ++ ++ spi-max-frequency = <32000000>; ++ rotate = <90>; ++ fps = <25>; ++ bgr; ++ buswidth = <8>; ++ dc-gpios = <&gpio 25 0>; ++ debug = <0>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c1>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ ft6236: ft6236@38 { ++ compatible = "focaltech,ft6236"; ++ reg = <0x38>; ++ ++ interrupt-parent = <&gpio>; ++ interrupts = <24 2>; ++ touchscreen-size-x = <240>; ++ touchscreen-size-y = <320>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&pitft>,"spi-max-frequency:0"; ++ rotate = <&pitft>,"rotate:0"; ++ fps = <&pitft>,"fps:0"; ++ debug = <&pitft>,"debug:0"; ++ touch-sizex = <&ft6236>,"touchscreen-size-x?"; ++ touch-sizey = <&ft6236>,"touchscreen-size-y?"; ++ touch-invx = <&ft6236>,"touchscreen-inverted-x?"; ++ touch-invy = <&ft6236>,"touchscreen-inverted-y?"; ++ touch-swapxy = <&ft6236>,"touchscreen-swapped-x-y?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts b/arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts +new file mode 100644 +index 000000000000..4a4a3f44c29d +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pitft28-resistive-overlay.dts +@@ -0,0 +1,119 @@ ++/* ++ * Device Tree overlay for Adafruit PiTFT 2.8" resistive touch screen ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ pitft_pins: pitft_pins { ++ brcm,pins = <24 25>; ++ brcm,function = <0 1>; /* in out */ ++ brcm,pull = <2 0>; /* pullup none */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pitft: pitft@0{ ++ compatible = "ilitek,ili9340"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pitft_pins>; ++ ++ spi-max-frequency = <32000000>; ++ rotate = <90>; ++ fps = <25>; ++ bgr; ++ buswidth = <8>; ++ dc-gpios = <&gpio 25 0>; ++ debug = <0>; ++ }; ++ ++ pitft_ts@1 { ++ compatible = "st,stmpe610"; ++ reg = <1>; ++ ++ spi-max-frequency = <500000>; ++ irq-gpio = <&gpio 24 0x2>; /* IRQF_TRIGGER_FALLING */ ++ interrupts = <24 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ ++ stmpe_touchscreen { ++ compatible = "st,stmpe-ts"; ++ st,sample-time = <4>; ++ st,mod-12b = <1>; ++ st,ref-sel = <0>; ++ st,adc-freq = <2>; ++ st,ave-ctrl = <3>; ++ st,touch-det-delay = <4>; ++ st,settling = <2>; ++ st,fraction-z = <7>; ++ st,i-drive = <0>; ++ }; ++ ++ stmpe_gpio: stmpe_gpio { ++ #gpio-cells = <2>; ++ compatible = "st,stmpe-gpio"; ++ /* ++ * only GPIO2 is wired/available ++ * and it is wired to the backlight ++ */ ++ st,norequest-mask = <0x7b>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path = "/soc"; ++ __overlay__ { ++ backlight { ++ compatible = "gpio-backlight"; ++ gpios = <&stmpe_gpio 2 0>; ++ default-on; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&pitft>,"spi-max-frequency:0"; ++ rotate = <&pitft>,"rotate:0"; ++ fps = <&pitft>,"fps:0"; ++ debug = <&pitft>,"debug:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/pitft35-resistive-overlay.dts b/arch/arm/boot/dts/overlays/pitft35-resistive-overlay.dts +new file mode 100644 +index 000000000000..37629f18a740 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pitft35-resistive-overlay.dts +@@ -0,0 +1,119 @@ ++/* ++ * Device Tree overlay for Adafruit PiTFT 3.5" resistive touch screen ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ pitft_pins: pitft_pins { ++ brcm,pins = <24 25>; ++ brcm,function = <0 1>; /* in out */ ++ brcm,pull = <2 0>; /* pullup none */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pitft: pitft@0{ ++ compatible = "himax,hx8357d", "adafruit,yx350hv15"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pitft_pins>; ++ ++ spi-max-frequency = <32000000>; ++ rotate = <90>; ++ fps = <25>; ++ bgr; ++ buswidth = <8>; ++ dc-gpios = <&gpio 25 0>; ++ debug = <0>; ++ }; ++ ++ pitft_ts@1 { ++ compatible = "st,stmpe610"; ++ reg = <1>; ++ ++ spi-max-frequency = <500000>; ++ irq-gpio = <&gpio 24 0x2>; /* IRQF_TRIGGER_FALLING */ ++ interrupts = <24 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ ++ stmpe_touchscreen { ++ compatible = "st,stmpe-ts"; ++ st,sample-time = <4>; ++ st,mod-12b = <1>; ++ st,ref-sel = <0>; ++ st,adc-freq = <2>; ++ st,ave-ctrl = <3>; ++ st,touch-det-delay = <4>; ++ st,settling = <2>; ++ st,fraction-z = <7>; ++ st,i-drive = <0>; ++ }; ++ ++ stmpe_gpio: stmpe_gpio { ++ #gpio-cells = <2>; ++ compatible = "st,stmpe-gpio"; ++ /* ++ * only GPIO2 is wired/available ++ * and it is wired to the backlight ++ */ ++ st,norequest-mask = <0x7b>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@5 { ++ target-path = "/soc"; ++ __overlay__ { ++ backlight { ++ compatible = "gpio-backlight"; ++ gpios = <&stmpe_gpio 2 0>; ++ default-on; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&pitft>,"spi-max-frequency:0"; ++ rotate = <&pitft>,"rotate:0"; ++ fps = <&pitft>,"fps:0"; ++ debug = <&pitft>,"debug:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/pps-gpio-overlay.dts b/arch/arm/boot/dts/overlays/pps-gpio-overlay.dts +new file mode 100644 +index 000000000000..524a1c1d3670 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pps-gpio-overlay.dts +@@ -0,0 +1,38 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ pps: pps@12 { ++ compatible = "pps-gpio"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pps_pins>; ++ gpios = <&gpio 18 0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ pps_pins: pps_pins@12 { ++ brcm,pins = <18>; ++ brcm,function = <0>; // in ++ brcm,pull = <0>; // off ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpiopin = <&pps>,"gpios:4", ++ <&pps>,"reg:0", ++ <&pps_pins>,"brcm,pins:0", ++ <&pps_pins>,"reg:0"; ++ assert_falling_edge = <&pps>,"assert-falling-edge?"; ++ capture_clear = <&pps>,"capture-clear?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts b/arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts +new file mode 100644 +index 000000000000..4ddbbfa04065 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pwm-2chan-overlay.dts +@@ -0,0 +1,49 @@ ++/dts-v1/; ++/plugin/; ++ ++/* ++This is the 2-channel overlay - only use it if you need both channels. ++ ++Legal pin,function combinations for each channel: ++ PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0) 52,5(Alt1) ++ PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1) ++ ++N.B.: ++ 1) Pin 18 is the only one available on all platforms, and ++ it is the one used by the I2S audio interface. ++ Pins 12 and 13 might be better choices on an A+, B+ or Pi2. ++ 2) The onboard analogue audio output uses both PWM channels. ++ 3) So be careful mixing audio and PWM. ++*/ ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ pwm_pins: pwm_pins { ++ brcm,pins = <18 19>; ++ brcm,function = <2 2>; /* Alt5 */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&pwm>; ++ frag1: __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pwm_pins>; ++ assigned-clock-rates = <100000000>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ pin = <&pwm_pins>,"brcm,pins:0"; ++ pin2 = <&pwm_pins>,"brcm,pins:4"; ++ func = <&pwm_pins>,"brcm,function:0"; ++ func2 = <&pwm_pins>,"brcm,function:4"; ++ clock = <&frag1>,"assigned-clock-rates:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/pwm-ir-tx-overlay.dts b/arch/arm/boot/dts/overlays/pwm-ir-tx-overlay.dts +new file mode 100644 +index 000000000000..119caf746b3b +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pwm-ir-tx-overlay.dts +@@ -0,0 +1,40 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ pwm0_pins: pwm0_pins { ++ brcm,pins = <18>; ++ brcm,function = <2>; /* Alt5 */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&pwm>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pwm0_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "/"; ++ __overlay__ { ++ pwm-ir-transmitter { ++ compatible = "pwm-ir-tx"; ++ pwms = <&pwm 0 100>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpio_pin = <&pwm0_pins>, "brcm,pins:0"; ++ func = <&pwm0_pins>,"brcm,function:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/pwm-overlay.dts b/arch/arm/boot/dts/overlays/pwm-overlay.dts +new file mode 100644 +index 000000000000..92876ab3bc8c +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/pwm-overlay.dts +@@ -0,0 +1,45 @@ ++/dts-v1/; ++/plugin/; ++ ++/* ++Legal pin,function combinations for each channel: ++ PWM0: 12,4(Alt0) 18,2(Alt5) 40,4(Alt0) 52,5(Alt1) ++ PWM1: 13,4(Alt0) 19,2(Alt5) 41,4(Alt0) 45,4(Alt0) 53,5(Alt1) ++ ++N.B.: ++ 1) Pin 18 is the only one available on all platforms, and ++ it is the one used by the I2S audio interface. ++ Pins 12 and 13 might be better choices on an A+, B+ or Pi2. ++ 2) The onboard analogue audio output uses both PWM channels. ++ 3) So be careful mixing audio and PWM. ++*/ ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ pwm_pins: pwm_pins { ++ brcm,pins = <18>; ++ brcm,function = <2>; /* Alt5 */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&pwm>; ++ frag1: __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pwm_pins>; ++ assigned-clock-rates = <100000000>; ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ pin = <&pwm_pins>,"brcm,pins:0"; ++ func = <&pwm_pins>,"brcm,function:0"; ++ clock = <&frag1>,"assigned-clock-rates:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/qca7000-overlay.dts b/arch/arm/boot/dts/overlays/qca7000-overlay.dts +new file mode 100644 +index 000000000000..9a451202a2eb +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/qca7000-overlay.dts +@@ -0,0 +1,55 @@ ++// Overlay for the Qualcomm Atheros QCA7000 on I2SE's PLC Stamp micro EVK ++// Visit: https://www.i2se.com/product/plc-stamp-micro-evk for details ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ eth1: qca7000@0 { ++ compatible = "qca,qca7000"; ++ reg = <0>; /* CE0 */ ++ pinctrl-names = "default"; ++ pinctrl-0 = <ð1_pins>; ++ interrupt-parent = <&gpio>; ++ interrupts = <23 0x1>; /* rising edge */ ++ spi-max-frequency = <12000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ eth1_pins: eth1_pins { ++ brcm,pins = <23>; ++ brcm,function = <0>; /* in */ ++ brcm,pull = <0>; /* none */ ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ int_pin = <ð1>, "interrupts:0", ++ <ð1_pins>, "brcm,pins:0"; ++ speed = <ð1>, "spi-max-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/rotary-encoder-overlay.dts b/arch/arm/boot/dts/overlays/rotary-encoder-overlay.dts +new file mode 100644 +index 000000000000..ea1d952734e9 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rotary-encoder-overlay.dts +@@ -0,0 +1,59 @@ ++// Device tree overlay for GPIO connected rotary encoder. ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ rotary_pins: rotary_pins@4 { ++ brcm,pins = <4 17>; /* gpio 4 17 */ ++ brcm,function = <0 0>; /* input */ ++ brcm,pull = <2 2>; /* pull-up */ ++ }; ++ ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ rotary: rotary@4 { ++ compatible = "rotary-encoder"; ++ status = "okay"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&rotary_pins>; ++ gpios = <&gpio 4 0>, <&gpio 17 0>; ++ linux,axis = <0>; /* REL_X */ ++ rotary-encoder,encoding = "gray"; ++ rotary-encoder,steps = <24>; /* 24 default */ ++ rotary-encoder,steps-per-period = <1>; /* corresponds to full period mode. See README */ ++ }; ++ }; ++ ++ }; ++ ++ __overrides__ { ++ pin_a = <&rotary>,"gpios:4", ++ <&rotary_pins>,"brcm,pins:0", ++ /* modify reg values to allow multiple instantiation */ ++ <&rotary>,"reg:0", ++ <&rotary_pins>,"reg:0"; ++ pin_b = <&rotary>,"gpios:16", ++ <&rotary_pins>,"brcm,pins:4"; ++ relative_axis = <&rotary>,"rotary-encoder,relative-axis?"; ++ linux_axis = <&rotary>,"linux,axis:0"; ++ rollover = <&rotary>,"rotary-encoder,rollover?"; ++ steps-per-period = <&rotary>,"rotary-encoder,steps-per-period:0"; ++ steps = <&rotary>,"rotary-encoder,steps:0"; ++ wakeup = <&rotary>,"wakeup-source?"; ++ encoding = <&rotary>,"rotary-encoder,encoding"; ++ /* legacy parameters*/ ++ rotary0_pin_a = <&rotary>,"gpios:4", ++ <&rotary_pins>,"brcm,pins:0"; ++ rotary0_pin_b = <&rotary>,"gpios:16", ++ <&rotary_pins>,"brcm,pins:4"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/rpi-backlight-overlay.dts b/arch/arm/boot/dts/overlays/rpi-backlight-overlay.dts +new file mode 100644 +index 000000000000..cac5e44c6ec5 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-backlight-overlay.dts +@@ -0,0 +1,21 @@ ++/* ++ * Devicetree overlay for mailbox-driven Raspberry Pi DSI Display ++ * backlight controller ++ */ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ rpi_backlight: rpi_backlight { ++ compatible = "raspberrypi,rpi-backlight"; ++ firmware = <&firmware>; ++ status = "okay"; ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/rpi-cirrus-wm5102-overlay.dts b/arch/arm/boot/dts/overlays/rpi-cirrus-wm5102-overlay.dts +new file mode 100644 +index 000000000000..ed0c2745399f +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-cirrus-wm5102-overlay.dts +@@ -0,0 +1,172 @@ ++// Definitions for the Cirrus Logic Audio Card ++/dts-v1/; ++/plugin/; ++#include ++#include ++#include ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ wlf_5102_pins: wlf_5102_pins { ++ brcm,pins = <17 22 27>; ++ brcm,function = < ++ BCM2835_FSEL_GPIO_OUT ++ BCM2835_FSEL_GPIO_OUT ++ BCM2835_FSEL_GPIO_IN ++ >; ++ }; ++ wlf_8804_pins: wlf_8804_pins { ++ brcm,pins = <8>; ++ brcm,function = ; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spi0_cs_pins>; ++ __overlay__ { ++ brcm,pins = <7>; ++ brcm,function = ; ++ }; ++ }; ++ ++ ++ fragment@3 { ++ target-path = "/"; ++ __overlay__ { ++ rpi_cirrus_reg_1v8: rpi_cirrus_reg_1v8 { ++ compatible = "regulator-fixed"; ++ regulator-name = "RPi-Cirrus 1v8"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ regulator-always-on; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&spi0>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ cs-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; ++ ++ wm5102@0{ ++ compatible = "wlf,wm5102"; ++ reg = <0>; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&wlf_5102_pins>; ++ ++ spi-max-frequency = <500000>; ++ ++ interrupt-parent = <&gpio>; ++ interrupts = <27 8>; ++ interrupt-controller; ++ #interrupt-cells = <2>; ++ ++ gpio-controller; ++ #gpio-cells = <2>; ++ ++ LDOVDD-supply = <&rpi_cirrus_reg_1v8>; ++ AVDD-supply = <&rpi_cirrus_reg_1v8>; ++ DBVDD1-supply = <&rpi_cirrus_reg_1v8>; ++ DBVDD2-supply = <&vdd_3v3_reg>; ++ DBVDD3-supply = <&vdd_3v3_reg>; ++ CPVDD-supply = <&rpi_cirrus_reg_1v8>; ++ SPKVDDL-supply = <&vdd_5v0_reg>; ++ SPKVDDR-supply = <&vdd_5v0_reg>; ++ DCVDD-supply = <&arizona_ldo1>; ++ ++ reset-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; ++ wlf,ldoena = <&gpio 22 GPIO_ACTIVE_HIGH>; ++ wlf,gpio-defaults = < ++ ARIZONA_GP_DEFAULT ++ ARIZONA_GP_DEFAULT ++ ARIZONA_GP_DEFAULT ++ ARIZONA_GP_DEFAULT ++ ARIZONA_GP_DEFAULT ++ >; ++ wlf,micd-configs = <0 1 0>; ++ wlf,dmic-ref = < ++ ARIZONA_DMIC_MICVDD ++ ARIZONA_DMIC_MICBIAS2 ++ ARIZONA_DMIC_MICVDD ++ ARIZONA_DMIC_MICVDD ++ >; ++ wlf,inmode = < ++ ARIZONA_INMODE_DIFF ++ ARIZONA_INMODE_DMIC ++ ARIZONA_INMODE_SE ++ ARIZONA_INMODE_DIFF ++ >; ++ status = "okay"; ++ ++ arizona_ldo1: ldo1 { ++ regulator-name = "LDO1"; ++ // default constraints as in ++ // arizona-ldo1.c ++ regulator-min-microvolt = <1200000>; ++ regulator-max-microvolt = <1800000>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@7 { ++ target = <&i2c1>; ++ __overlay__ { ++ status = "okay"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ wm8804@3b { ++ compatible = "wlf,wm8804"; ++ reg = <0x3b>; ++ status = "okay"; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&wlf_8804_pins>; ++ ++ PVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ wlf,reset-gpio = <&gpio 8 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++ }; ++ ++ fragment@8 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "wlf,rpi-cirrus"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/rpi-dac-overlay.dts b/arch/arm/boot/dts/overlays/rpi-dac-overlay.dts +new file mode 100644 +index 000000000000..07a915342702 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-dac-overlay.dts +@@ -0,0 +1,34 @@ ++// Definitions for RPi DAC ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ pcm1794a-codec { ++ #sound-dai-cells = <0>; ++ compatible = "ti,pcm1794a"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "rpi,rpi-dac"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/rpi-display-overlay.dts b/arch/arm/boot/dts/overlays/rpi-display-overlay.dts +new file mode 100644 +index 000000000000..de87432ff2be +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-display-overlay.dts +@@ -0,0 +1,91 @@ ++/* ++ * Device Tree overlay for rpi-display by Watterott ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ rpi_display_pins: rpi_display_pins { ++ brcm,pins = <18 23 24 25>; ++ brcm,function = <1 1 1 0>; /* out out out in */ ++ brcm,pull = <0 0 0 2>; /* - - - up */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ rpidisplay: rpi-display@0{ ++ compatible = "ilitek,ili9341"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&rpi_display_pins>; ++ ++ spi-max-frequency = <32000000>; ++ rotate = <270>; ++ bgr; ++ fps = <30>; ++ buswidth = <8>; ++ reset-gpios = <&gpio 23 1>; ++ dc-gpios = <&gpio 24 0>; ++ led-gpios = <&gpio 18 0>; ++ debug = <0>; ++ }; ++ ++ rpidisplay_ts: rpi-display-ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <25 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 25 1>; ++ ti,x-plate-ohms = /bits/ 16 <60>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ __overrides__ { ++ speed = <&rpidisplay>,"spi-max-frequency:0"; ++ rotate = <&rpidisplay>,"rotate:0"; ++ fps = <&rpidisplay>,"fps:0"; ++ debug = <&rpidisplay>,"debug:0"; ++ xohms = <&rpidisplay_ts>,"ti,x-plate-ohms;0"; ++ swapxy = <&rpidisplay_ts>,"ti,swap-xy?"; ++ backlight = <&rpidisplay>,"led-gpios:4", ++ <&rpi_display_pins>,"brcm,pins:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/rpi-ft5406-overlay.dts b/arch/arm/boot/dts/overlays/rpi-ft5406-overlay.dts +new file mode 100644 +index 000000000000..8483c4f4b2eb +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-ft5406-overlay.dts +@@ -0,0 +1,25 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/soc/firmware"; ++ __overlay__ { ++ ts: touchscreen { ++ compatible = "raspberrypi,firmware-ts"; ++ touchscreen-size-x = <800>; ++ touchscreen-size-y = <480>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ touchscreen-size-x = <&ts>,"touchscreen-size-x:0"; ++ touchscreen-size-y = <&ts>,"touchscreen-size-y:0"; ++ touchscreen-inverted-x = <&ts>,"touchscreen-inverted-x?"; ++ touchscreen-inverted-y = <&ts>,"touchscreen-inverted-y?"; ++ touchscreen-swapped-x-y = <&ts>,"touchscreen-swapped-x-y?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/rpi-poe-overlay.dts b/arch/arm/boot/dts/overlays/rpi-poe-overlay.dts +new file mode 100644 +index 000000000000..544038b614e1 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-poe-overlay.dts +@@ -0,0 +1,95 @@ ++/* ++ * Overlay for the Raspberry Pi POE HAT. ++ */ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ fan0: rpi-poe-fan@0 { ++ compatible = "raspberrypi,rpi-poe-fan"; ++ firmware = <&firmware>; ++ cooling-min-state = <0>; ++ cooling-max-state = <4>; ++ #cooling-cells = <2>; ++ cooling-levels = <0 31 63 150 255>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&cpu_thermal>; ++ __overlay__ { ++ trips { ++ trip0: trip0 { ++ temperature = <40000>; ++ hysteresis = <2000>; ++ type = "active"; ++ }; ++ trip1: trip1 { ++ temperature = <45000>; ++ hysteresis = <2000>; ++ type = "active"; ++ }; ++ trip2: trip2 { ++ temperature = <50000>; ++ hysteresis = <2000>; ++ type = "active"; ++ }; ++ trip3: trip3 { ++ temperature = <55000>; ++ hysteresis = <5000>; ++ type = "active"; ++ }; ++ }; ++ cooling-maps { ++ map0 { ++ trip = <&trip0>; ++ cooling-device = <&fan0 0 1>; ++ }; ++ map1 { ++ trip = <&trip1>; ++ cooling-device = <&fan0 1 2>; ++ }; ++ map2 { ++ trip = <&trip2>; ++ cooling-device = <&fan0 2 3>; ++ }; ++ map3 { ++ trip = <&trip3>; ++ cooling-device = <&fan0 3 4>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "/__overrides__"; ++ __overlay__ { ++ poe_fan_temp0 = <&trip0>,"temperature:0"; ++ poe_fan_temp0_hyst = <&trip0>,"hysteresis:0"; ++ poe_fan_temp1 = <&trip1>,"temperature:0"; ++ poe_fan_temp1_hyst = <&trip1>,"hysteresis:0"; ++ poe_fan_temp2 = <&trip2>,"temperature:0"; ++ poe_fan_temp2_hyst = <&trip2>,"hysteresis:0"; ++ poe_fan_temp3 = <&trip3>,"temperature:0"; ++ poe_fan_temp3_hyst = <&trip3>,"hysteresis:0"; ++ }; ++ }; ++ ++ __overrides__ { ++ poe_fan_temp0 = <&trip0>,"temperature:0"; ++ poe_fan_temp0_hyst = <&trip0>,"hysteresis:0"; ++ poe_fan_temp1 = <&trip1>,"temperature:0"; ++ poe_fan_temp1_hyst = <&trip1>,"hysteresis:0"; ++ poe_fan_temp2 = <&trip2>,"temperature:0"; ++ poe_fan_temp2_hyst = <&trip2>,"hysteresis:0"; ++ poe_fan_temp3 = <&trip3>,"temperature:0"; ++ poe_fan_temp3_hyst = <&trip3>,"hysteresis:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/rpi-proto-overlay.dts b/arch/arm/boot/dts/overlays/rpi-proto-overlay.dts +new file mode 100644 +index 000000000000..9cda044a0f62 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-proto-overlay.dts +@@ -0,0 +1,39 @@ ++// Definitions for Rpi-Proto ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8731@1a { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8731"; ++ reg = <0x1a>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "rpi,rpi-proto"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/rpi-sense-overlay.dts b/arch/arm/boot/dts/overlays/rpi-sense-overlay.dts +new file mode 100644 +index 000000000000..89d8d2ea6b2e +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-sense-overlay.dts +@@ -0,0 +1,47 @@ ++// rpi-sense HAT ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ rpi-sense@46 { ++ compatible = "rpi,rpi-sense"; ++ reg = <0x46>; ++ keys-int-gpios = <&gpio 23 1>; ++ status = "okay"; ++ }; ++ ++ lsm9ds1-magn@1c { ++ compatible = "st,lsm9ds1-magn"; ++ reg = <0x1c>; ++ status = "okay"; ++ }; ++ ++ lsm9ds1-accel6a { ++ compatible = "st,lsm9ds1-accel"; ++ reg = <0x6a>; ++ status = "okay"; ++ }; ++ ++ lps25h-press@5c { ++ compatible = "st,lps25h-press"; ++ reg = <0x5c>; ++ status = "okay"; ++ }; ++ ++ hts221-humid@5f { ++ compatible = "st,hts221-humid", "st,hts221"; ++ reg = <0x5f>; ++ status = "okay"; ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/rpi-tv-overlay.dts b/arch/arm/boot/dts/overlays/rpi-tv-overlay.dts +new file mode 100644 +index 000000000000..3c97a545d820 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpi-tv-overlay.dts +@@ -0,0 +1,34 @@ ++// rpi-tv HAT ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ cxd2880@0 { ++ compatible = "sony,cxd2880"; ++ reg = <0>; /* CE0 */ ++ spi-max-frequency = <50000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++}; +diff --git a/arch/arm/boot/dts/overlays/rpivid-v4l2-overlay.dts b/arch/arm/boot/dts/overlays/rpivid-v4l2-overlay.dts +new file mode 100644 +index 000000000000..0a611b31b9d4 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rpivid-v4l2-overlay.dts +@@ -0,0 +1,61 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Definitions for Raspberry Pi video decode engine ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/{ ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&scb>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <2>; ++ #size-cells = <2>; ++ ++ codec@7eb10000 { ++ compatible = "raspberrypi,rpivid-vid-decoder"; ++ reg = <0x0 0x7eb10000 0x0 0x1000>, /* INTC */ ++ <0x0 0x7eb00000 0x0 0x10000>; /* HEVC */ ++ reg-names = "intc", ++ "hevc"; ++ ++ interrupts = ; ++ ++ clocks = <&hevc_clk>; ++ clock-names = "hevc"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&scb>; ++ __overlay__ { ++ hevc-decoder@7eb00000 { ++ status = "disabled"; ++ }; ++ rpivid-local-intc@7eb10000 { ++ status = "disabled"; ++ }; ++ h264-decoder@7eb20000 { ++ status = "disabled"; ++ }; ++ vp9-decoder@7eb30000 { ++ status = "disabled"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "/"; ++ __overlay__ { ++ hevc_clk: hevc_clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <500000000>; ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/rra-digidac1-wm8741-audio-overlay.dts b/arch/arm/boot/dts/overlays/rra-digidac1-wm8741-audio-overlay.dts +new file mode 100644 +index 000000000000..87e9a326eff1 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/rra-digidac1-wm8741-audio-overlay.dts +@@ -0,0 +1,49 @@ ++// Definitions for RRA DigiDAC1 Audio card ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ wm8804@3b { ++ #sound-dai-cells = <0>; ++ compatible = "wlf,wm8804"; ++ reg = <0x3b>; ++ status = "okay"; ++ PVDD-supply = <&vdd_3v3_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ }; ++ ++ wm8742: wm8741@1a { ++ compatible = "wlf,wm8741"; ++ reg = <0x1a>; ++ status = "okay"; ++ AVDD-supply = <&vdd_5v0_reg>; ++ DVDD-supply = <&vdd_3v3_reg>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "rra,digidac1-soundcard"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/sainsmart18-overlay.dts b/arch/arm/boot/dts/overlays/sainsmart18-overlay.dts +new file mode 100644 +index 000000000000..c51f1c030a55 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sainsmart18-overlay.dts +@@ -0,0 +1,52 @@ ++/* ++ * Device Tree overlay for the Sainsmart 1.8" TFT LCD with ST7735R chip 160x128 ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ ss18: sainsmart18@0 { ++ compatible = "fbtft,sainsmart18"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ spi-max-frequency = <40000000>; ++ rotate = <90>; ++ buswidth = <8>; ++ fps = <50>; ++ height = <160>; ++ width = <128>; ++ reset-gpios = <&gpio 25 1>; ++ dc-gpios = <&gpio 24 0>; ++ debug = <0>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&ss18>,"spi-max-frequency:0"; ++ rotate = <&ss18>,"rotate:0"; ++ fps = <&ss18>,"fps:0"; ++ bgr = <&ss18>,"bgr?"; ++ debug = <&ss18>,"debug:0"; ++ dc_pin = <&ss18>,"dc-gpios:4"; ++ reset_pin = <&ss18>,"reset-gpios:4"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/sc16is750-i2c-overlay.dts b/arch/arm/boot/dts/overlays/sc16is750-i2c-overlay.dts +new file mode 100644 +index 000000000000..04d74d62897b +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sc16is750-i2c-overlay.dts +@@ -0,0 +1,43 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ sc16is750: sc16is750@48 { ++ compatible = "nxp,sc16is750"; ++ reg = <0x48>; /* i2c address */ ++ clocks = <&sc16is750_clk>; ++ interrupt-parent = <&gpio>; ++ interrupts = <24 2>; /* IRQ_TYPE_EDGE_FALLING */ ++ gpio-controller; ++ #gpio-cells = <2>; ++ i2c-max-frequency = <400000>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ sc16is750_clk: sc16is750_i2c_clk@48 { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <14745600>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ int_pin = <&sc16is750>,"interrupts:0"; ++ addr = <&sc16is750>,"reg:0", <&sc16is750_clk>,"name"; ++ xtal = <&sc16is750_clk>,"clock-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/sc16is752-i2c-overlay.dts b/arch/arm/boot/dts/overlays/sc16is752-i2c-overlay.dts +new file mode 100644 +index 000000000000..da05e981314c +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sc16is752-i2c-overlay.dts +@@ -0,0 +1,43 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_arm>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ sc16is752: sc16is752@48 { ++ compatible = "nxp,sc16is752"; ++ reg = <0x48>; /* i2c address */ ++ clocks = <&sc16is752_clk>; ++ interrupt-parent = <&gpio>; ++ interrupts = <24 2>; /* IRQ_TYPE_EDGE_FALLING */ ++ gpio-controller; ++ #gpio-cells = <2>; ++ i2c-max-frequency = <400000>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ sc16is752_clk: sc16is752_i2c_clk@48 { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <14745600>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ int_pin = <&sc16is752>,"interrupts:0"; ++ addr = <&sc16is752>,"reg:0",<&sc16is752_clk>,"name"; ++ xtal = <&sc16is752_clk>,"clock-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/sc16is752-spi0-overlay.dts b/arch/arm/boot/dts/overlays/sc16is752-spi0-overlay.dts +new file mode 100644 +index 000000000000..a49a04722b99 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sc16is752-spi0-overlay.dts +@@ -0,0 +1,49 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ sc16is752: sc16is752@0 { ++ compatible = "nxp,sc16is752"; ++ reg = <0>; /* CE0 */ ++ clocks = <&sc16is752_clk>; ++ interrupt-parent = <&gpio>; ++ interrupts = <24 2>; /* IRQ_TYPE_EDGE_FALLING */ ++ gpio-controller; ++ #gpio-cells = <2>; ++ spi-max-frequency = <4000000>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "/"; ++ __overlay__ { ++ sc16is752_clk: sc16is752_spi0_0_clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <14745600>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ int_pin = <&sc16is752>,"interrupts:0"; ++ xtal = <&sc16is752_clk>,"clock-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/sc16is752-spi1-overlay.dts b/arch/arm/boot/dts/overlays/sc16is752-spi1-overlay.dts +new file mode 100644 +index 000000000000..730c6e8cd614 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sc16is752-spi1-overlay.dts +@@ -0,0 +1,67 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi1_pins: spi1_pins { ++ brcm,pins = <19 20 21>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi1_cs_pins: spi1_cs_pins { ++ brcm,pins = <18>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi1_pins &spi1_cs_pins>; ++ cs-gpios = <&gpio 18 1>; ++ status = "okay"; ++ ++ sc16is752: sc16is752@0 { ++ compatible = "nxp,sc16is752"; ++ reg = <0>; /* CE0 */ ++ clocks = <&sc16is752_clk>; ++ interrupt-parent = <&gpio>; ++ interrupts = <24 2>; /* IRQ_TYPE_EDGE_FALLING */ ++ gpio-controller; ++ #gpio-cells = <2>; ++ spi-max-frequency = <4000000>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target-path = "/"; ++ __overlay__ { ++ sc16is752_clk: sc16is752_spi1_0_clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <14745600>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ int_pin = <&sc16is752>,"interrupts:0"; ++ xtal = <&sc16is752_clk>,"clock-frequency:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/sdhost-overlay.dts b/arch/arm/boot/dts/overlays/sdhost-overlay.dts +new file mode 100644 +index 000000000000..0b72b4eeac88 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sdhost-overlay.dts +@@ -0,0 +1,38 @@ ++/dts-v1/; ++/plugin/; ++ ++/* Provide backwards compatible aliases for the old sdhost dtparams. */ ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&sdhost>; ++ frag0: __overlay__ { ++ brcm,overclock-50 = <0>; ++ brcm,pio-limit = <1>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&mmc>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&mmcnr>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ __overrides__ { ++ overclock_50 = <&frag0>,"brcm,overclock-50:0"; ++ force_pio = <&frag0>,"brcm,force-pio?"; ++ pio_limit = <&frag0>,"brcm,pio-limit:0"; ++ debug = <&frag0>,"brcm,debug?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/sdio-overlay.dts b/arch/arm/boot/dts/overlays/sdio-overlay.dts +new file mode 100644 +index 000000000000..873e49056379 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sdio-overlay.dts +@@ -0,0 +1,77 @@ ++/dts-v1/; ++/plugin/; ++ ++/* Enable SDIO from MMC interface via various GPIO groups */ ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&mmcnr>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&mmc>; ++ sdio_ovl: __overlay__ { ++ pinctrl-0 = <&sdio_ovl_pins>; ++ pinctrl-names = "default"; ++ non-removable; ++ bus-width = <4>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ sdio_ovl_pins: sdio_ovl_pins { ++ brcm,pins = <22 23 24 25 26 27>; ++ brcm,function = <7>; /* ALT3 = SD1 */ ++ brcm,pull = <0 2 2 2 2 2>; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sdio_ovl_pins>; ++ __dormant__ { ++ brcm,pins = <22 23 24 25>; ++ brcm,pull = <0 2 2 2>; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&sdio_ovl_pins>; ++ __dormant__ { ++ brcm,pins = <34 35 36 37>; ++ brcm,pull = <0 2 2 2>; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&sdio_ovl_pins>; ++ __dormant__ { ++ brcm,pins = <34 35 36 37 38 39>; ++ brcm,pull = <0 2 2 2 2 2>; ++ }; ++ }; ++ ++ fragment@6 { ++ target-path = "/aliases"; ++ __overlay__ { ++ mmc1 = "/soc/mmc@7e300000"; ++ }; ++ }; ++ ++ __overrides__ { ++ poll_once = <&sdio_ovl>,"non-removable?"; ++ bus_width = <&sdio_ovl>,"bus-width:0"; ++ sdio_overclock = <&sdio_ovl>,"brcm,overclock-50:0"; ++ gpios_22_25 = <0>,"=3"; ++ gpios_34_37 = <0>,"=4"; ++ gpios_34_39 = <0>,"=5"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/sdtweak-overlay.dts b/arch/arm/boot/dts/overlays/sdtweak-overlay.dts +new file mode 100644 +index 000000000000..38157d2f9bf3 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sdtweak-overlay.dts +@@ -0,0 +1,25 @@ ++/dts-v1/; ++/plugin/; ++ ++/* Provide backwards compatible aliases for the old sdhost dtparams. */ ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&sdhost>; ++ frag0: __overlay__ { ++ brcm,overclock-50 = <0>; ++ brcm,pio-limit = <1>; ++ }; ++ }; ++ ++ __overrides__ { ++ overclock_50 = <&frag0>,"brcm,overclock-50:0"; ++ force_pio = <&frag0>,"brcm,force-pio?"; ++ pio_limit = <&frag0>,"brcm,pio-limit:0"; ++ debug = <&frag0>,"brcm,debug?"; ++ enable = <&frag0>,"status"; ++ poll_once = <&frag0>,"non-removable?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/sh1106-spi-overlay.dts b/arch/arm/boot/dts/overlays/sh1106-spi-overlay.dts +new file mode 100644 +index 000000000000..57a0cc9b1741 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sh1106-spi-overlay.dts +@@ -0,0 +1,84 @@ ++/* ++ * Device Tree overlay for SH1106 based SPI OLED display ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ sh1106_pins: sh1106_pins { ++ brcm,pins = <25 24>; ++ brcm,function = <1 1>; /* out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sh1106: sh1106@0{ ++ compatible = "sinowealth,sh1106"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sh1106_pins>; ++ ++ spi-max-frequency = <4000000>; ++ bgr = <0>; ++ bpp = <1>; ++ rotate = <0>; ++ fps = <25>; ++ buswidth = <8>; ++ reset-gpios = <&gpio 25 1>; ++ dc-gpios = <&gpio 24 0>; ++ debug = <0>; ++ ++ sinowealth,height = <64>; ++ sinowealth,width = <128>; ++ sinowealth,page-offset = <0>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&sh1106>,"spi-max-frequency:0"; ++ rotate = <&sh1106>,"rotate:0"; ++ fps = <&sh1106>,"fps:0"; ++ debug = <&sh1106>,"debug:0"; ++ dc_pin = <&sh1106>,"dc-gpios:4", ++ <&sh1106_pins>,"brcm,pins:4"; ++ reset_pin = <&sh1106>,"reset-gpios:4", ++ <&sh1106_pins>,"brcm,pins:0"; ++ height = <&sh1106>,"sinowealth,height:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/smi-dev-overlay.dts b/arch/arm/boot/dts/overlays/smi-dev-overlay.dts +new file mode 100644 +index 000000000000..bafab6c92506 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/smi-dev-overlay.dts +@@ -0,0 +1,20 @@ ++// Description: Overlay to enable character device interface for SMI. ++// Author: Luke Wren ++ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&soc>; ++ __overlay__ { ++ smi_dev { ++ compatible = "brcm,bcm2835-smi-dev"; ++ smi_handle = <&smi>; ++ status = "okay"; ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/smi-nand-overlay.dts b/arch/arm/boot/dts/overlays/smi-nand-overlay.dts +new file mode 100644 +index 000000000000..ae1e50329d66 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/smi-nand-overlay.dts +@@ -0,0 +1,66 @@ ++// Description: Overlay to enable NAND flash through ++// the secondary memory interface ++// Author: Luke Wren ++ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&smi>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&smi_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&soc>; ++ __overlay__ { ++ nand: flash@0 { ++ compatible = "brcm,bcm2835-smi-nand"; ++ smi_handle = <&smi>; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ status = "okay"; ++ ++ partition@0 { ++ label = "stage2"; ++ // 128k ++ reg = <0 0x20000>; ++ read-only; ++ }; ++ partition@1 { ++ label = "firmware"; ++ // 16M ++ reg = <0x20000 0x1000000>; ++ read-only; ++ }; ++ partition@2 { ++ label = "root"; ++ // 2G (will need to use 64 bit for >=4G) ++ reg = <0x1020000 0x80000000>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&gpio>; ++ __overlay__ { ++ smi_pins: smi_pins { ++ brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11 ++ 12 13 14 15>; ++ /* Alt 1: SMI */ ++ brcm,function = <5 5 5 5 5 5 5 5 5 5 5 ++ 5 5 5 5 5>; ++ /* /CS, /WE and /OE are pulled high, as they are ++ generally active low signals */ ++ brcm,pull = <2 2 2 2 2 2 2 2 0 0 0 0 0 0 0 0>; ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/smi-overlay.dts b/arch/arm/boot/dts/overlays/smi-overlay.dts +new file mode 100644 +index 000000000000..bb8c7830df23 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/smi-overlay.dts +@@ -0,0 +1,37 @@ ++// Description: Overlay to enable the secondary memory interface peripheral ++// Author: Luke Wren ++ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&smi>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&smi_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ smi_pins: smi_pins { ++ /* Don't configure the top two address bits, as ++ these are already used as ID_SD and ID_SC */ ++ brcm,pins = <2 3 4 5 6 7 8 9 10 11 12 13 14 15 ++ 16 17 18 19 20 21 22 23 24 25>; ++ /* Alt 1: SMI */ ++ brcm,function = <5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 ++ 5 5 5 5 5 5 5 5 5>; ++ /* /CS, /WE and /OE are pulled high, as they are ++ generally active low signals */ ++ brcm,pull = <2 2 2 2 2 2 0 0 0 0 0 0 0 0 0 0 0 ++ 0 0 0 0 0 0 0>; ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi-gpio35-39-overlay.dts b/arch/arm/boot/dts/overlays/spi-gpio35-39-overlay.dts +new file mode 100644 +index 000000000000..a132b8637c31 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi-gpio35-39-overlay.dts +@@ -0,0 +1,31 @@ ++/* ++ * Device tree overlay to move spi0 to gpio 35 to 39 on CM ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ cs-gpios = <&gpio 36 1>, <&gpio 35 1>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi0_cs_pins>; ++ __overlay__ { ++ brcm,pins = <36 35>; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spi0_pins>; ++ __overlay__ { ++ brcm,pins = <37 38 39>; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi-gpio40-45-overlay.dts b/arch/arm/boot/dts/overlays/spi-gpio40-45-overlay.dts +new file mode 100644 +index 000000000000..9ebcaf1b5ea0 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi-gpio40-45-overlay.dts +@@ -0,0 +1,36 @@ ++/* ++ * Boot EEPROM overlay ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ cs-gpios = <&gpio 43 1>, <&gpio 44 1>, <&gpio 45 1>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi0_cs_pins>; ++ __overlay__ { ++ brcm,pins = <45 44 43>; ++ brcm,function = <1>; /* output */ ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spi0_pins>; ++ __overlay__ { ++ brcm,pins = <40 41 42>; ++ brcm,function = <3>; /* alt4 */ ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi-rtc-overlay.dts b/arch/arm/boot/dts/overlays/spi-rtc-overlay.dts +new file mode 100644 +index 000000000000..9664afc9845c +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi-rtc-overlay.dts +@@ -0,0 +1,33 @@ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spidev0>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ rtc-pcf2123@0 { ++ compatible = "nxp,rtc-pcf2123"; ++ spi-max-frequency = <5000000>; ++ spi-cs-high = <1>; ++ reg = <0>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ pcf2123 = <0>, "=0=1"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi0-1cs-overlay.dts b/arch/arm/boot/dts/overlays/spi0-1cs-overlay.dts +new file mode 100644 +index 000000000000..e6eb66e2076a +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi0-1cs-overlay.dts +@@ -0,0 +1,42 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0_cs_pins>; ++ frag0: __overlay__ { ++ brcm,pins = <8>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi0>; ++ frag1: __overlay__ { ++ cs-gpios = <&gpio 8 1>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&spi0_pins>; ++ __dormant__ { ++ brcm,pins = <10 11>; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&frag0>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ no_miso = <0>,"=3"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi0-2cs-overlay.dts b/arch/arm/boot/dts/overlays/spi0-2cs-overlay.dts +new file mode 100644 +index 000000000000..df6519537c3a +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi0-2cs-overlay.dts +@@ -0,0 +1,37 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0_cs_pins>; ++ frag0: __overlay__ { ++ brcm,pins = <8 7>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi0>; ++ frag1: __overlay__ { ++ cs-gpios = <&gpio 8 1>, <&gpio 7 1>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spi0_pins>; ++ __dormant__ { ++ brcm,pins = <10 11>; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&frag0>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs1_pin = <&frag0>,"brcm,pins:4", ++ <&frag1>,"cs-gpios:16"; ++ no_miso = <0>,"=2"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi1-1cs-overlay.dts b/arch/arm/boot/dts/overlays/spi1-1cs-overlay.dts +new file mode 100644 +index 000000000000..ea2794bc5fd5 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi1-1cs-overlay.dts +@@ -0,0 +1,57 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi1_pins: spi1_pins { ++ brcm,pins = <19 20 21>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi1_cs_pins: spi1_cs_pins { ++ brcm,pins = <18>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi1>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi1_pins &spi1_cs_pins>; ++ cs-gpios = <&gpio 18 1>; ++ status = "okay"; ++ ++ spidev1_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&spi1_cs_pins>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs0_spidev = <&spidev1_0>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi1-2cs-overlay.dts b/arch/arm/boot/dts/overlays/spi1-2cs-overlay.dts +new file mode 100644 +index 000000000000..dab34ee79ae2 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi1-2cs-overlay.dts +@@ -0,0 +1,69 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi1_pins: spi1_pins { ++ brcm,pins = <19 20 21>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi1_cs_pins: spi1_cs_pins { ++ brcm,pins = <18 17>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi1>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi1_pins &spi1_cs_pins>; ++ cs-gpios = <&gpio 18 1>, <&gpio 17 1>; ++ status = "okay"; ++ ++ spidev1_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ ++ spidev1_1: spidev@1 { ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&spi1_cs_pins>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs1_pin = <&spi1_cs_pins>,"brcm,pins:4", ++ <&frag1>,"cs-gpios:16"; ++ cs0_spidev = <&spidev1_0>,"status"; ++ cs1_spidev = <&spidev1_1>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi1-3cs-overlay.dts b/arch/arm/boot/dts/overlays/spi1-3cs-overlay.dts +new file mode 100644 +index 000000000000..bc7e7d04324b +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi1-3cs-overlay.dts +@@ -0,0 +1,81 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi1_pins: spi1_pins { ++ brcm,pins = <19 20 21>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi1_cs_pins: spi1_cs_pins { ++ brcm,pins = <18 17 16>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi1>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi1_pins &spi1_cs_pins>; ++ cs-gpios = <&gpio 18 1>, <&gpio 17 1>, <&gpio 16 1>; ++ status = "okay"; ++ ++ spidev1_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ ++ spidev1_1: spidev@1 { ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ ++ spidev1_2: spidev@2 { ++ compatible = "spidev"; ++ reg = <2>; /* CE2 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&spi1_cs_pins>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs1_pin = <&spi1_cs_pins>,"brcm,pins:4", ++ <&frag1>,"cs-gpios:16"; ++ cs2_pin = <&spi1_cs_pins>,"brcm,pins:8", ++ <&frag1>,"cs-gpios:28"; ++ cs0_spidev = <&spidev1_0>,"status"; ++ cs1_spidev = <&spidev1_1>,"status"; ++ cs2_spidev = <&spidev1_2>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi2-1cs-overlay.dts b/arch/arm/boot/dts/overlays/spi2-1cs-overlay.dts +new file mode 100644 +index 000000000000..2a29750462af +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi2-1cs-overlay.dts +@@ -0,0 +1,57 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi2_pins: spi2_pins { ++ brcm,pins = <40 41 42>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi2_cs_pins: spi2_cs_pins { ++ brcm,pins = <43>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi2>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi2_pins &spi2_cs_pins>; ++ cs-gpios = <&gpio 43 1>; ++ status = "okay"; ++ ++ spidev2_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&spi2_cs_pins>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs0_spidev = <&spidev2_0>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi2-2cs-overlay.dts b/arch/arm/boot/dts/overlays/spi2-2cs-overlay.dts +new file mode 100644 +index 000000000000..642678fc9ddd +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi2-2cs-overlay.dts +@@ -0,0 +1,69 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi2_pins: spi2_pins { ++ brcm,pins = <40 41 42>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi2_cs_pins: spi2_cs_pins { ++ brcm,pins = <43 44>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi2>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi2_pins &spi2_cs_pins>; ++ cs-gpios = <&gpio 43 1>, <&gpio 44 1>; ++ status = "okay"; ++ ++ spidev2_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ ++ spidev2_1: spidev@1 { ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&spi2_cs_pins>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs1_pin = <&spi2_cs_pins>,"brcm,pins:4", ++ <&frag1>,"cs-gpios:16"; ++ cs0_spidev = <&spidev2_0>,"status"; ++ cs1_spidev = <&spidev2_1>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi2-3cs-overlay.dts b/arch/arm/boot/dts/overlays/spi2-3cs-overlay.dts +new file mode 100644 +index 000000000000..28d40c6c3c37 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi2-3cs-overlay.dts +@@ -0,0 +1,81 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&gpio>; ++ __overlay__ { ++ spi2_pins: spi2_pins { ++ brcm,pins = <40 41 42>; ++ brcm,function = <3>; /* alt4 */ ++ }; ++ ++ spi2_cs_pins: spi2_cs_pins { ++ brcm,pins = <43 44 45>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi2>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi2_pins &spi2_cs_pins>; ++ cs-gpios = <&gpio 43 1>, <&gpio 44 1>, <&gpio 45 1>; ++ status = "okay"; ++ ++ spidev2_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ ++ spidev2_1: spidev@1 { ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ ++ spidev2_2: spidev@2 { ++ compatible = "spidev"; ++ reg = <2>; /* CE2 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&aux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&spi2_cs_pins>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs1_pin = <&spi2_cs_pins>,"brcm,pins:4", ++ <&frag1>,"cs-gpios:16"; ++ cs2_pin = <&spi2_cs_pins>,"brcm,pins:8", ++ <&frag1>,"cs-gpios:28"; ++ cs0_spidev = <&spidev2_0>,"status"; ++ cs1_spidev = <&spidev2_1>,"status"; ++ cs2_spidev = <&spidev2_2>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi3-1cs-overlay.dts b/arch/arm/boot/dts/overlays/spi3-1cs-overlay.dts +new file mode 100644 +index 000000000000..335af8637051 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi3-1cs-overlay.dts +@@ -0,0 +1,44 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&spi3_cs_pins>; ++ frag0: __overlay__ { ++ brcm,pins = <0>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi3>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi3_pins &spi3_cs_pins>; ++ cs-gpios = <&gpio 0 1>; ++ status = "okay"; ++ ++ spidev3_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&frag0>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs0_spidev = <&spidev3_0>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi3-2cs-overlay.dts b/arch/arm/boot/dts/overlays/spi3-2cs-overlay.dts +new file mode 100644 +index 000000000000..ce65da27f767 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi3-2cs-overlay.dts +@@ -0,0 +1,56 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&spi3_cs_pins>; ++ frag0: __overlay__ { ++ brcm,pins = <0 24>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi3>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi3_pins &spi3_cs_pins>; ++ cs-gpios = <&gpio 0 1>, <&gpio 24 1>; ++ status = "okay"; ++ ++ spidev3_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ ++ spidev3_1: spidev@1 { ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&frag0>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs1_pin = <&frag0>,"brcm,pins:4", ++ <&frag1>,"cs-gpios:16"; ++ cs0_spidev = <&spidev3_0>,"status"; ++ cs1_spidev = <&spidev3_1>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi4-1cs-overlay.dts b/arch/arm/boot/dts/overlays/spi4-1cs-overlay.dts +new file mode 100644 +index 000000000000..85d70b40352b +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi4-1cs-overlay.dts +@@ -0,0 +1,44 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&spi4_cs_pins>; ++ frag0: __overlay__ { ++ brcm,pins = <4>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi4>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi4_pins &spi4_cs_pins>; ++ cs-gpios = <&gpio 4 1>; ++ status = "okay"; ++ ++ spidev4_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&frag0>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs0_spidev = <&spidev4_0>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi4-2cs-overlay.dts b/arch/arm/boot/dts/overlays/spi4-2cs-overlay.dts +new file mode 100644 +index 000000000000..8bc2215a6a7e +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi4-2cs-overlay.dts +@@ -0,0 +1,56 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&spi4_cs_pins>; ++ frag0: __overlay__ { ++ brcm,pins = <4 25>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi4>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi4_pins &spi4_cs_pins>; ++ cs-gpios = <&gpio 4 1>, <&gpio 25 1>; ++ status = "okay"; ++ ++ spidev4_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ ++ spidev4_1: spidev@1 { ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&frag0>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs1_pin = <&frag0>,"brcm,pins:4", ++ <&frag1>,"cs-gpios:16"; ++ cs0_spidev = <&spidev4_0>,"status"; ++ cs1_spidev = <&spidev4_1>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi5-1cs-overlay.dts b/arch/arm/boot/dts/overlays/spi5-1cs-overlay.dts +new file mode 100644 +index 000000000000..c0f8cb8510ee +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi5-1cs-overlay.dts +@@ -0,0 +1,44 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&spi5_cs_pins>; ++ frag0: __overlay__ { ++ brcm,pins = <12>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi5>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi5_pins &spi5_cs_pins>; ++ cs-gpios = <&gpio 12 1>; ++ status = "okay"; ++ ++ spidev5_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&frag0>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs0_spidev = <&spidev5_0>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi5-2cs-overlay.dts b/arch/arm/boot/dts/overlays/spi5-2cs-overlay.dts +new file mode 100644 +index 000000000000..7758b9c00b4e +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi5-2cs-overlay.dts +@@ -0,0 +1,56 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&spi5_cs_pins>; ++ frag0: __overlay__ { ++ brcm,pins = <12 26>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi5>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi5_pins &spi5_cs_pins>; ++ cs-gpios = <&gpio 12 1>, <&gpio 26 1>; ++ status = "okay"; ++ ++ spidev5_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ ++ spidev5_1: spidev@1 { ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&frag0>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs1_pin = <&frag0>,"brcm,pins:4", ++ <&frag1>,"cs-gpios:16"; ++ cs0_spidev = <&spidev5_0>,"status"; ++ cs1_spidev = <&spidev5_1>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi6-1cs-overlay.dts b/arch/arm/boot/dts/overlays/spi6-1cs-overlay.dts +new file mode 100644 +index 000000000000..8c8a953eca01 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi6-1cs-overlay.dts +@@ -0,0 +1,44 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&spi6_cs_pins>; ++ frag0: __overlay__ { ++ brcm,pins = <18>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi6>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi6_pins &spi6_cs_pins>; ++ cs-gpios = <&gpio 18 1>; ++ status = "okay"; ++ ++ spidev6_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&frag0>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs0_spidev = <&spidev6_0>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/spi6-2cs-overlay.dts b/arch/arm/boot/dts/overlays/spi6-2cs-overlay.dts +new file mode 100644 +index 000000000000..2ff897f21aed +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/spi6-2cs-overlay.dts +@@ -0,0 +1,56 @@ ++/dts-v1/; ++/plugin/; ++ ++ ++/ { ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&spi6_cs_pins>; ++ frag0: __overlay__ { ++ brcm,pins = <18 27>; ++ brcm,function = <1>; /* output */ ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spi6>; ++ frag1: __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&spi6_pins &spi6_cs_pins>; ++ cs-gpios = <&gpio 18 1>, <&gpio 27 1>; ++ status = "okay"; ++ ++ spidev6_0: spidev@0 { ++ compatible = "spidev"; ++ reg = <0>; /* CE0 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ ++ spidev6_1: spidev@1 { ++ compatible = "spidev"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <125000000>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ cs0_pin = <&frag0>,"brcm,pins:0", ++ <&frag1>,"cs-gpios:4"; ++ cs1_pin = <&frag0>,"brcm,pins:4", ++ <&frag1>,"cs-gpios:16"; ++ cs0_spidev = <&spidev6_0>,"status"; ++ cs1_spidev = <&spidev6_1>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/ssd1306-overlay.dts b/arch/arm/boot/dts/overlays/ssd1306-overlay.dts +new file mode 100644 +index 000000000000..84cf10e489d3 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ssd1306-overlay.dts +@@ -0,0 +1,36 @@ ++// Overlay for SSD1306 128x64 and 128x32 OLED displays ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c1>; ++ __overlay__ { ++ status = "okay"; ++ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ ssd1306: oled@3c{ ++ compatible = "solomon,ssd1306fb-i2c"; ++ reg = <0x3c>; ++ solomon,width = <128>; ++ solomon,height = <64>; ++ solomon,page-offset = <0>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ address = <&ssd1306>,"reg:0"; ++ width = <&ssd1306>,"solomon,width:0"; ++ height = <&ssd1306>,"solomon,height:0"; ++ offset = <&ssd1306>,"solomon,page-offset:0"; ++ normal = <&ssd1306>,"solomon,segment-no-remap?"; ++ sequential = <&ssd1306>,"solomon,com-seq?"; ++ remapped = <&ssd1306>,"solomon,com-lrremap?"; ++ inverted = <&ssd1306>,"solomon,com-invdir?"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/ssd1306-spi-overlay.dts b/arch/arm/boot/dts/overlays/ssd1306-spi-overlay.dts +new file mode 100644 +index 000000000000..ffc90c7cecf6 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ssd1306-spi-overlay.dts +@@ -0,0 +1,84 @@ ++/* ++ * Device Tree overlay for SSD1306 based SPI OLED display ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ ssd1306_pins: ssd1306_pins { ++ brcm,pins = <25 24>; ++ brcm,function = <1 1>; /* out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ ssd1306: ssd1306@0{ ++ compatible = "solomon,ssd1306"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&ssd1306_pins>; ++ ++ spi-max-frequency = <10000000>; ++ bgr = <0>; ++ bpp = <1>; ++ rotate = <0>; ++ fps = <25>; ++ buswidth = <8>; ++ reset-gpios = <&gpio 25 1>; ++ dc-gpios = <&gpio 24 0>; ++ debug = <0>; ++ ++ solomon,height = <64>; ++ solomon,width = <128>; ++ solomon,page-offset = <0>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&ssd1306>,"spi-max-frequency:0"; ++ rotate = <&ssd1306>,"rotate:0"; ++ fps = <&ssd1306>,"fps:0"; ++ debug = <&ssd1306>,"debug:0"; ++ dc_pin = <&ssd1306>,"dc-gpios:4", ++ <&ssd1306_pins>,"brcm,pins:4"; ++ reset_pin = <&ssd1306>,"reset-gpios:4", ++ <&ssd1306_pins>,"brcm,pins:0"; ++ height = <&ssd1306>,"solomon,height:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/ssd1351-spi-overlay.dts b/arch/arm/boot/dts/overlays/ssd1351-spi-overlay.dts +new file mode 100644 +index 000000000000..ffc872c60648 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/ssd1351-spi-overlay.dts +@@ -0,0 +1,83 @@ ++/* ++ * Device Tree overlay for SSD1351 based SPI OLED display ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ ssd1351_pins: ssd1351_pins { ++ brcm,pins = <25 24>; ++ brcm,function = <1 1>; /* out out */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ ssd1351: ssd1351@0{ ++ compatible = "solomon,ssd1351"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&ssd1351_pins>; ++ ++ spi-max-frequency = <4500000>; ++ bgr = <0>; ++ bpp = <16>; ++ rotate = <0>; ++ fps = <25>; ++ buswidth = <8>; ++ reset-gpios = <&gpio 25 1>; ++ dc-gpios = <&gpio 24 0>; ++ debug = <0>; ++ ++ solomon,height = <128>; ++ solomon,width = <128>; ++ solomon,page-offset = <0>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&ssd1351>,"spi-max-frequency:0"; ++ rotate = <&ssd1351>,"rotate:0"; ++ fps = <&ssd1351>,"fps:0"; ++ debug = <&ssd1351>,"debug:0"; ++ dc_pin = <&ssd1351>,"dc-gpios:4", ++ <&ssd1351_pins>,"brcm,pins:4"; ++ reset_pin = <&ssd1351>,"reset-gpios:4", ++ <&ssd1351_pins>,"brcm,pins:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/superaudioboard-overlay.dts b/arch/arm/boot/dts/overlays/superaudioboard-overlay.dts +new file mode 100755 +index 000000000000..bad61535981e +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/superaudioboard-overlay.dts +@@ -0,0 +1,73 @@ ++// Definitions for SuperAudioBoard ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&sound>; ++ __overlay__ { ++ compatible = "simple-audio-card"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ ++ simple-audio-card,name = "SuperAudioBoard"; ++ ++ simple-audio-card,widgets = ++ "Line", "Line In", ++ "Line", "Line Out"; ++ ++ simple-audio-card,routing = ++ "Line Out","AOUTA+", ++ "Line Out","AOUTA-", ++ "Line Out","AOUTB+", ++ "Line Out","AOUTB-", ++ "AINA","Line In", ++ "AINB","Line In"; ++ ++ simple-audio-card,format = "i2s"; ++ ++ simple-audio-card,bitclock-master = <&sound_master>; ++ simple-audio-card,frame-master = <&sound_master>; ++ ++ simple-audio-card,cpu { ++ sound-dai = <&i2s>; ++ dai-tdm-slot-num = <2>; ++ dai-tdm-slot-width = <32>; ++ }; ++ ++ sound_master: simple-audio-card,codec { ++ sound-dai = <&cs4271>; ++ system-clock-frequency = <24576000>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ cs4271: cs4271@10 { ++ #sound-dai-cells = <0>; ++ compatible = "cirrus,cs4271"; ++ reg = <0x10>; ++ status = "okay"; ++ reset-gpio = <&gpio 26 0>; /* Pin 26, active high */ ++ }; ++ }; ++ }; ++ __overrides__ { ++ gpiopin = <&cs4271>,"reset-gpio:4"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/sx150x-overlay.dts b/arch/arm/boot/dts/overlays/sx150x-overlay.dts +new file mode 100644 +index 000000000000..1d1069345da2 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/sx150x-overlay.dts +@@ -0,0 +1,1706 @@ ++// Definitions for SX150x I2C GPIO Expanders from Semtech ++ ++// dtparams: ++// sx150-- - Enables SX150X device on I2C# with slave address . may be 1-9. ++// may be 0 or 1. Permissible values of (which is denoted in hex) ++// depend on the device variant. ++// For SX1501, SX1502, SX1504 and SX1505, may be 20 or 21. ++// For SX1503 and SX1506, may be 20. ++// For SX1507 and SX1509, may be 3E, 3F, 70 or 71. ++// For SX1508, may be 20, 21, 22 or 23. ++// sx150---int-gpio - Integer, enables interrupts on SX150X device on I2C# with slave address , ++// specifies the GPIO pin to which NINT output of SX150X is connected. ++// ++// ++// Example 1: A single SX1505 device on I2C#1 with its slave address set to 0x20 and NINT output connected to GPIO25: ++// dtoverlay=sx150x:sx1505-1-20,sx1505-1-20-int-gpio=25 ++// ++// Example 2: Two SX1507 devices on I2C#0 with their slave addresses set to 0x3E and 0x70 (interrupts not used): ++// dtoverlay=sx150x:sx1507-0-3E,sx1507-0-70 ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ // Enable I2C#0 interface ++ fragment@0 { ++ target = <&i2c0>; ++ __dormant__ { ++ status = "okay"; ++ }; ++ }; ++ ++ // Enable I2C#1 interface ++ fragment@1 { ++ target = <&i2c1>; ++ __dormant__ { ++ status = "okay"; ++ }; ++ }; ++ ++ // Enable a SX1501 on I2C#0 at slave addr 0x20 ++ fragment@2 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1501_0_20: sx150x@20 { ++ compatible = "semtech,sx1501q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1501-0-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1501 on I2C#1 at slave addr 0x20 ++ fragment@3 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1501_1_20: sx150x@20 { ++ compatible = "semtech,sx1501q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1501-1-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1501 on I2C#0 at slave addr 0x21 ++ fragment@4 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1501_0_21: sx150x@21 { ++ compatible = "semtech,sx1501q"; ++ reg = <0x21>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1501-0-21-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1501 on I2C#1 at slave addr 0x21 ++ fragment@5 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1501_1_21: sx150x@21 { ++ compatible = "semtech,sx1501q"; ++ reg = <0x21>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1501-1-21-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1502 on I2C#0 at slave addr 0x20 ++ fragment@6 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1502_0_20: sx150x@20 { ++ compatible = "semtech,sx1502q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1502-0-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1502 on I2C#1 at slave addr 0x20 ++ fragment@7 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1502_1_20: sx150x@20 { ++ compatible = "semtech,sx1502q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1502-1-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1502 on I2C#0 at slave addr 0x21 ++ fragment@8 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1502_0_21: sx150x@21 { ++ compatible = "semtech,sx1502q"; ++ reg = <0x21>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1502-0-21-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1502 on I2C#1 at slave addr 0x21 ++ fragment@9 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1502_1_21: sx150x@21 { ++ compatible = "semtech,sx1502q"; ++ reg = <0x21>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1501-1-21-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1503 on I2C#0 at slave addr 0x20 ++ fragment@10 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1503_0_20: sx150x@20 { ++ compatible = "semtech,sx1503q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1503-0-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1503 on I2C#1 at slave addr 0x20 ++ fragment@11 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1503_1_20: sx150x@20 { ++ compatible = "semtech,sx1503q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1503-1-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1504 on I2C#0 at slave addr 0x20 ++ fragment@12 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1504_0_20: sx150x@20 { ++ compatible = "semtech,sx1504q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1504-0-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1504 on I2C#1 at slave addr 0x20 ++ fragment@13 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1504_1_20: sx150x@20 { ++ compatible = "semtech,sx1504q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1504-1-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1504 on I2C#0 at slave addr 0x21 ++ fragment@14 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1504_0_21: sx150x@21 { ++ compatible = "semtech,sx1504q"; ++ reg = <0x21>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1504-0-21-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1504 on I2C#1 at slave addr 0x21 ++ fragment@15 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1504_1_21: sx150x@21 { ++ compatible = "semtech,sx1504q"; ++ reg = <0x21>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1504-1-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1505 on I2C#0 at slave addr 0x20 ++ fragment@16 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1505_0_20: sx150x@20 { ++ compatible = "semtech,sx1505q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1505-0-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1505 on I2C#1 at slave addr 0x20 ++ fragment@17 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1505_1_20: sx150x@20 { ++ compatible = "semtech,sx1505q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1505-1-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1505 on I2C#0 at slave addr 0x21 ++ fragment@18 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1505_0_21: sx150x@21 { ++ compatible = "semtech,sx1505q"; ++ reg = <0x21>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1505-0-21-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1505 on I2C#1 at slave addr 0x21 ++ fragment@19 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1505_1_21: sx150x@21 { ++ compatible = "semtech,sx1505q"; ++ reg = <0x21>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1505-1-21-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1506 on I2C#0 at slave addr 0x20 ++ fragment@20 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1506_0_20: sx150x@20 { ++ compatible = "semtech,sx1506q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1506-0-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1506 on I2C#1 at slave addr 0x20 ++ fragment@21 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1506_1_20: sx150x@20 { ++ compatible = "semtech,sx1506q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1506-1-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1507 on I2C#0 at slave addr 0x3E ++ fragment@22 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1507_0_3E: sx150x@3E { ++ compatible = "semtech,sx1507q"; ++ reg = <0x3E>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1507_0_3E-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1507 on I2C#1 at slave addr 0x3E ++ fragment@23 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1507_1_3E: sx150x@3E { ++ compatible = "semtech,sx1507q"; ++ reg = <0x3E>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1507_1_3E-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1507 on I2C#0 at slave addr 0x3F ++ fragment@24 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1507_0_3F: sx150x@3F { ++ compatible = "semtech,sx1507q"; ++ reg = <0x3F>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1507_0_3F-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1507 on I2C#1 at slave addr 0x3F ++ fragment@25 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1507_1_3F: sx150x@3F { ++ compatible = "semtech,sx1507q"; ++ reg = <0x3F>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1507_1_3F-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1507 on I2C#0 at slave addr 0x70 ++ fragment@26 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1507_0_70: sx150x@70 { ++ compatible = "semtech,sx1507q"; ++ reg = <0x70>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1507-0-70-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1507 on I2C#1 at slave addr 0x70 ++ fragment@27 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1507_1_70: sx150x@70 { ++ compatible = "semtech,sx1507q"; ++ reg = <0x70>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1507-1-70-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1507 on I2C#0 at slave addr 0x71 ++ fragment@28 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1507_0_71: sx150x@71 { ++ compatible = "semtech,sx1507q"; ++ reg = <0x71>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1507-0-71-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1507 on I2C#1 at slave addr 0x71 ++ fragment@29 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1507_1_71: sx150x@71 { ++ compatible = "semtech,sx1507q"; ++ reg = <0x71>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1507-1-71-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1508 on I2C#0 at slave addr 0x20 ++ fragment@30 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1508_0_20: sx150x@20 { ++ compatible = "semtech,sx1508q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1508-0-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1508 on I2C#1 at slave addr 0x20 ++ fragment@31 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1508_1_20: sx150x@20 { ++ compatible = "semtech,sx1508q"; ++ reg = <0x20>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1508-1-20-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1508 on I2C#0 at slave addr 0x21 ++ fragment@32 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1508_0_21: sx150x@21 { ++ compatible = "semtech,sx1508q"; ++ reg = <0x21>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1508-0-21-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1508 on I2C#1 at slave addr 0x21 ++ fragment@33 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1508_1_21: sx150x@21 { ++ compatible = "semtech,sx1508q"; ++ reg = <0x21>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1508-1-21-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1508 on I2C#0 at slave addr 0x22 ++ fragment@34 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1508_0_22: sx150x@22 { ++ compatible = "semtech,sx1508q"; ++ reg = <0x22>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1508-0-22-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1508 on I2C#1 at slave addr 0x22 ++ fragment@35 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1508_1_22: sx150x@22 { ++ compatible = "semtech,sx1508q"; ++ reg = <0x22>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1508-1-22-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1508 on I2C#0 at slave addr 0x23 ++ fragment@36 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1508_0_23: sx150x@23 { ++ compatible = "semtech,sx1508q"; ++ reg = <0x23>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1508-0-23-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1508 on I2C#1 at slave addr 0x23 ++ fragment@37 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1508_1_23: sx150x@23 { ++ compatible = "semtech,sx1508q"; ++ reg = <0x23>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1508-1-23-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1509 on I2C#0 at slave addr 0x3E ++ fragment@38 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1509_0_3E: sx150x@3E { ++ compatible = "semtech,sx1509q"; ++ reg = <0x3E>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1509_0_3E-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1509 on I2C#1 at slave addr 0x3E ++ fragment@39 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1509_1_3E: sx150x@3E { ++ compatible = "semtech,sx1509q"; ++ reg = <0x3E>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1509_1_3E-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1509 on I2C#0 at slave addr 0x3F ++ fragment@40 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1509_0_3F: sx150x@3F { ++ compatible = "semtech,sx1509q"; ++ reg = <0x3F>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1509_0_3F-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1509 on I2C#1 at slave addr 0x3F ++ fragment@41 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1509_1_3F: sx150x@3F { ++ compatible = "semtech,sx1509q"; ++ reg = <0x3F>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1509_1_3F-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1509 on I2C#0 at slave addr 0x70 ++ fragment@42 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1509_0_70: sx150x@70 { ++ compatible = "semtech,sx1509q"; ++ reg = <0x70>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1509-0-70-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1509 on I2C#1 at slave addr 0x70 ++ fragment@43 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1509_1_70: sx150x@70 { ++ compatible = "semtech,sx1509q"; ++ reg = <0x70>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1509-1-70-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1509 on I2C#0 at slave addr 0x71 ++ fragment@44 { ++ target = <&i2c0>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1509_0_71: sx150x@71 { ++ compatible = "semtech,sx1509q"; ++ reg = <0x71>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1509-0-71-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable a SX1509 on I2C#1 at slave addr 0x71 ++ fragment@45 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ sx1509_1_71: sx150x@71 { ++ compatible = "semtech,sx1509q"; ++ reg = <0x71>; ++ gpio-controller; ++ #gpio-cells = <2>; ++ #interrupt-cells = <2>; ++ interrupts = <25 2>; /* 1st word overwritten by sx1509-1-71-int-gpio parameter ++ 2nd word is 2 for falling-edge triggered */ ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1501 on I2C#0 at slave addr 0x20 ++ fragment@46 { ++ target = <&sx1501_0_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1501 on I2C#1 at slave addr 0x20 ++ fragment@47 { ++ target = <&sx1501_1_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1501 on I2C#0 at slave addr 0x21 ++ fragment@48 { ++ target = <&sx1501_0_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_21_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1501 on I2C#1 at slave addr 0x21 ++ fragment@49 { ++ target = <&sx1501_1_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_21_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1502 on I2C#0 at slave addr 0x20 ++ fragment@50 { ++ target = <&sx1502_0_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1502 on I2C#1 at slave addr 0x20 ++ fragment@51 { ++ target = <&sx1502_1_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1502 on I2C#0 at slave addr 0x21 ++ fragment@52 { ++ target = <&sx1502_0_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_21_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1502 on I2C#1 at slave addr 0x21 ++ fragment@53 { ++ target = <&sx1502_1_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_21_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1503 on I2C#0 at slave addr 0x20 ++ fragment@54 { ++ target = <&sx1503_0_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1503 on I2C#1 at slave addr 0x20 ++ fragment@55 { ++ target = <&sx1503_1_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1504 on I2C#0 at slave addr 0x20 ++ fragment@56 { ++ target = <&sx1504_0_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1504 on I2C#1 at slave addr 0x20 ++ fragment@57 { ++ target = <&sx1504_1_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1504 on I2C#0 at slave addr 0x21 ++ fragment@58 { ++ target = <&sx1504_0_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_21_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1504 on I2C#1 at slave addr 0x21 ++ fragment@59 { ++ target = <&sx1504_1_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_21_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1505 on I2C#0 at slave addr 0x20 ++ fragment@60 { ++ target = <&sx1505_0_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1505 on I2C#1 at slave addr 0x20 ++ fragment@61 { ++ target = <&sx1505_1_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1505 on I2C#0 at slave addr 0x21 ++ fragment@62 { ++ target = <&sx1505_0_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_21_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1505 on I2C#1 at slave addr 0x21 ++ fragment@63 { ++ target = <&sx1505_1_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_21_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1506 on I2C#0 at slave addr 0x20 ++ fragment@64 { ++ target = <&sx1506_0_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1506 on I2C#1 at slave addr 0x20 ++ fragment@65 { ++ target = <&sx1506_1_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1507 on I2C#0 at slave addr 0x3E ++ fragment@66 { ++ target = <&sx1507_0_3E>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_3E_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1507 on I2C#1 at slave addr 0x3E ++ fragment@67 { ++ target = <&sx1507_1_3E>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_3E_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1507 on I2C#0 at slave addr 0x3F ++ fragment@68 { ++ target = <&sx1507_0_3F>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_3F_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1507 on I2C#1 at slave addr 0x3F ++ fragment@69 { ++ target = <&sx1507_1_3F>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_3F_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1507 on I2C#0 at slave addr 0x70 ++ fragment@70 { ++ target = <&sx1507_0_70>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_70_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1507 on I2C#1 at slave addr 0x70 ++ fragment@71 { ++ target = <&sx1507_1_70>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_70_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1507 on I2C#0 at slave addr 0x71 ++ fragment@72 { ++ target = <&sx1507_0_71>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_71_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1507 on I2C#1 at slave addr 0x71 ++ fragment@73 { ++ target = <&sx1507_1_71>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_71_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1508 on I2C#0 at slave addr 0x20 ++ fragment@74 { ++ target = <&sx1508_0_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1508 on I2C#1 at slave addr 0x20 ++ fragment@75 { ++ target = <&sx1508_1_20>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_20_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1508 on I2C#0 at slave addr 0x21 ++ fragment@76 { ++ target = <&sx1508_0_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_21_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1508 on I2C#1 at slave addr 0x21 ++ fragment@77 { ++ target = <&sx1508_1_21>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_21_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1508 on I2C#0 at slave addr 0x22 ++ fragment@78 { ++ target = <&sx1508_0_22>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_22_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1508 on I2C#1 at slave addr 0x22 ++ fragment@79 { ++ target = <&sx1508_1_22>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_22_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1508 on I2C#0 at slave addr 0x23 ++ fragment@80 { ++ target = <&sx1508_0_23>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_23_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1508 on I2C#1 at slave addr 0x23 ++ fragment@81 { ++ target = <&sx1508_1_23>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_23_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1509 on I2C#0 at slave addr 0x3E ++ fragment@82 { ++ target = <&sx1509_0_3E>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_3E_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1509 on I2C#1 at slave addr 0x3E ++ fragment@83 { ++ target = <&sx1509_1_3E>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_3E_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1509 on I2C#0 at slave addr 0x3F ++ fragment@84 { ++ target = <&sx1509_0_3F>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_3F_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1509 on I2C#1 at slave addr 0x3F ++ fragment@85 { ++ target = <&sx1509_1_3F>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_3F_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1509 on I2C#0 at slave addr 0x70 ++ fragment@86 { ++ target = <&sx1509_0_70>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_70_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1509 on I2C#1 at slave addr 0x70 ++ fragment@87 { ++ target = <&sx1509_1_70>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_70_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1509 on I2C#0 at slave addr 0x71 ++ fragment@88 { ++ target = <&sx1509_0_71>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_0_71_pins>; ++ }; ++ }; ++ ++ // Enable interrupts for a SX1509 on I2C#1 at slave addr 0x71 ++ fragment@89 { ++ target = <&sx1509_1_71>; ++ __dormant__ { ++ interrupt-parent = <&gpio>; ++ interrupt-controller; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sx150x_1_71_pins>; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x20 ++ // Configure as a input with no pull-up/down ++ fragment@90 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_0_20_pins: sx150x_0_20_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-0-20-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x20 ++ // Configure as a input with no pull-up/down ++ fragment@91 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_1_20_pins: sx150x_1_20_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-1-20-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x21 ++ // Configure as a input with no pull-up/down ++ fragment@92 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_0_21_pins: sx150x_0_21_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-0-21-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x21 ++ // Configure as a input with no pull-up/down ++ fragment@93 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_1_21_pins: sx150x_1_21_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-1-21-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x22 ++ // Configure as a input with no pull-up/down ++ fragment@94 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_0_22_pins: sx150x_0_22_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-0-22-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x22 ++ // Configure as a input with no pull-up/down ++ fragment@95 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_1_22_pins: sx150x_1_22_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-1-22-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x23 ++ // Configure as a input with no pull-up/down ++ fragment@96 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_0_23_pins: sx150x_0_23_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-0-23-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x23 ++ // Configure as a input with no pull-up/down ++ fragment@97 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_1_23_pins: sx150x_1_23_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-1-23-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x3E ++ // Configure as a input with no pull-up/down ++ fragment@98 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_0_3E_pins: sx150x_0_3E_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-0-3E-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x3E ++ // Configure as a input with no pull-up/down ++ fragment@99 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_1_3E_pins: sx150x_1_3E_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-1-3E-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x3F ++ // Configure as a input with no pull-up/down ++ fragment@100 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_0_3F_pins: sx150x_0_3F_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-0-3F-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x3F ++ // Configure as a input with no pull-up/down ++ fragment@101 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_1_3F_pins: sx150x_1_3F_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-1-3F-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x70 ++ // Configure as a input with no pull-up/down ++ fragment@102 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_0_70_pins: sx150x_0_70_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-0-70-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x70 ++ // Configure as a input with no pull-up/down ++ fragment@103 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_1_70_pins: sx150x_1_70_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-1-70-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#0 interface at slave addr 0x71 ++ // Configure as a input with no pull-up/down ++ fragment@104 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_0_71_pins: sx150x_0_71_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-0-71-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ // Configure GPIO pin connected to NINT output of a SX150x on I2C#1 interface at slave addr 0x71 ++ // Configure as a input with no pull-up/down ++ fragment@105 { ++ target = <&gpio>; ++ __dormant__ { ++ sx150x_1_71_pins: sx150x_1_71_pins { ++ brcm,pins = <0>; /* overwritten by sx150x-1-71-int-gpio parameter */ ++ brcm,function = <0>; ++ brcm,pull = <0>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ sx1501-0-20 = <0>,"+0+2"; ++ sx1501-1-20 = <0>,"+1+3"; ++ sx1501-0-21 = <0>,"+0+4"; ++ sx1501-1-21 = <0>,"+1+5"; ++ sx1502-0-20 = <0>,"+0+6"; ++ sx1502-1-20 = <0>,"+1+7"; ++ sx1502-0-21 = <0>,"+0+8"; ++ sx1502-1-21 = <0>,"+1+9"; ++ sx1503-0-20 = <0>,"+0+10"; ++ sx1503-1-20 = <0>,"+1+11"; ++ sx1504-0-20 = <0>,"+0+12"; ++ sx1504-1-20 = <0>,"+1+13"; ++ sx1504-0-21 = <0>,"+0+14"; ++ sx1504-1-21 = <0>,"+1+15"; ++ sx1505-0-20 = <0>,"+0+16"; ++ sx1505-1-20 = <0>,"+1+17"; ++ sx1505-0-21 = <0>,"+0+18"; ++ sx1505-1-21 = <0>,"+1+19"; ++ sx1506-0-20 = <0>,"+0+20"; ++ sx1506-1-20 = <0>,"+1+21"; ++ sx1507-0-3E = <0>,"+0+22"; ++ sx1507-1-3E = <0>,"+1+23"; ++ sx1507-0-3F = <0>,"+0+24"; ++ sx1507-1-3F = <0>,"+1+25"; ++ sx1507-0-70 = <0>,"+0+26"; ++ sx1507-1-70 = <0>,"+1+27"; ++ sx1507-0-71 = <0>,"+0+28"; ++ sx1507-1-71 = <0>,"+1+29"; ++ sx1508-0-20 = <0>,"+0+30"; ++ sx1508-1-20 = <0>,"+1+31"; ++ sx1508-0-21 = <0>,"+0+32"; ++ sx1508-1-21 = <0>,"+1+33"; ++ sx1508-0-22 = <0>,"+0+34"; ++ sx1508-1-22 = <0>,"+1+35"; ++ sx1508-0-23 = <0>,"+0+36"; ++ sx1508-1-23 = <0>,"+1+37"; ++ sx1509-0-3E = <0>,"+0+38"; ++ sx1509-1-3E = <0>,"+1+39"; ++ sx1509-0-3F = <0>,"+0+40"; ++ sx1509-1-3F = <0>,"+1+41"; ++ sx1509-0-70 = <0>,"+0+42"; ++ sx1509-1-70 = <0>,"+1+43"; ++ sx1509-0-71 = <0>,"+0+44"; ++ sx1509-1-71 = <0>,"+1+45"; ++ sx1501-0-20-int-gpio = <0>,"+46+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1501_0_20>,"interrupts:0"; ++ sx1501-1-20-int-gpio = <0>,"+47+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1501_1_20>,"interrupts:0"; ++ sx1501-0-21-int-gpio = <0>,"+48+92", <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1501_0_21>,"interrupts:0"; ++ sx1501-1-21-int-gpio = <0>,"+49+93", <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1501_1_21>,"interrupts:0"; ++ sx1502-0-20-int-gpio = <0>,"+50+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1502_0_20>,"interrupts:0"; ++ sx1502-1-20-int-gpio = <0>,"+51+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1502_1_20>,"interrupts:0"; ++ sx1502-0-21-int-gpio = <0>,"+52+92", <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1502_0_21>,"interrupts:0"; ++ sx1502-1-21-int-gpio = <0>,"+53+93", <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1502_1_21>,"interrupts:0"; ++ sx1503-0-20-int-gpio = <0>,"+54+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1503_0_20>,"interrupts:0"; ++ sx1503-1-20-int-gpio = <0>,"+55+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1503_1_20>,"interrupts:0"; ++ sx1504-0-20-int-gpio = <0>,"+56+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1504_0_20>,"interrupts:0"; ++ sx1504-1-20-int-gpio = <0>,"+57+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1504_1_20>,"interrupts:0"; ++ sx1504-0-21-int-gpio = <0>,"+58+92", <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1504_0_21>,"interrupts:0"; ++ sx1504-1-21-int-gpio = <0>,"+59+93", <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1504_1_21>,"interrupts:0"; ++ sx1505-0-20-int-gpio = <0>,"+60+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1505_0_20>,"interrupts:0"; ++ sx1505-1-20-int-gpio = <0>,"+61+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1505_1_20>,"interrupts:0"; ++ sx1505-0-21-int-gpio = <0>,"+62+92", <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1505_0_21>,"interrupts:0"; ++ sx1505-1-21-int-gpio = <0>,"+63+93", <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1505_1_21>,"interrupts:0"; ++ sx1506-0-20-int-gpio = <0>,"+64+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1506_0_20>,"interrupts:0"; ++ sx1506-1-20-int-gpio = <0>,"+65+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1506_1_20>,"interrupts:0"; ++ sx1507-0-3E-int-gpio = <0>,"+66+98", <&sx150x_0_3E_pins>,"brcm,pins:0", <&sx1507_0_3E>,"interrupts:0"; ++ sx1507-1-3E-int-gpio = <0>,"+67+99", <&sx150x_1_3E_pins>,"brcm,pins:0", <&sx1507_1_3E>,"interrupts:0"; ++ sx1507-0-3F-int-gpio = <0>,"+68+100", <&sx150x_0_3F_pins>,"brcm,pins:0", <&sx1507_0_3F>,"interrupts:0"; ++ sx1507-1-3F-int-gpio = <0>,"+69+101", <&sx150x_1_3F_pins>,"brcm,pins:0", <&sx1507_1_3F>,"interrupts:0"; ++ sx1507-0-70-int-gpio = <0>,"+60+102", <&sx150x_0_70_pins>,"brcm,pins:0", <&sx1507_0_70>,"interrupts:0"; ++ sx1507-1-70-int-gpio = <0>,"+71+103", <&sx150x_1_70_pins>,"brcm,pins:0", <&sx1507_1_70>,"interrupts:0"; ++ sx1507-0-71-int-gpio = <0>,"+72+104", <&sx150x_0_71_pins>,"brcm,pins:0", <&sx1507_0_71>,"interrupts:0"; ++ sx1507-1-71-int-gpio = <0>,"+73+105", <&sx150x_1_71_pins>,"brcm,pins:0", <&sx1507_1_71>,"interrupts:0"; ++ sx1508-0-20-int-gpio = <0>,"+74+90", <&sx150x_0_20_pins>,"brcm,pins:0", <&sx1508_0_20>,"interrupts:0"; ++ sx1508-1-20-int-gpio = <0>,"+75+91", <&sx150x_1_20_pins>,"brcm,pins:0", <&sx1508_1_20>,"interrupts:0"; ++ sx1508-0-21-int-gpio = <0>,"+76+92", <&sx150x_0_21_pins>,"brcm,pins:0", <&sx1508_0_21>,"interrupts:0"; ++ sx1508-1-21-int-gpio = <0>,"+77+93", <&sx150x_1_21_pins>,"brcm,pins:0", <&sx1508_1_21>,"interrupts:0"; ++ sx1508-0-22-int-gpio = <0>,"+78+94", <&sx150x_0_22_pins>,"brcm,pins:0", <&sx1508_0_22>,"interrupts:0"; ++ sx1508-1-22-int-gpio = <0>,"+79+95", <&sx150x_1_22_pins>,"brcm,pins:0", <&sx1508_1_22>,"interrupts:0"; ++ sx1508-0-23-int-gpio = <0>,"+80+96", <&sx150x_0_23_pins>,"brcm,pins:0", <&sx1508_0_23>,"interrupts:0"; ++ sx1508-1-23-int-gpio = <0>,"+81+97", <&sx150x_1_23_pins>,"brcm,pins:0", <&sx1508_1_23>,"interrupts:0"; ++ sx1509-0-3E-int-gpio = <0>,"+82+98", <&sx150x_0_3E_pins>,"brcm,pins:0", <&sx1509_0_3E>,"interrupts:0"; ++ sx1509-1-3E-int-gpio = <0>,"+83+99", <&sx150x_1_3E_pins>,"brcm,pins:0", <&sx1509_1_3E>,"interrupts:0"; ++ sx1509-0-3F-int-gpio = <0>,"+84+100", <&sx150x_0_3F_pins>,"brcm,pins:0", <&sx1509_0_3F>,"interrupts:0"; ++ sx1509-1-3F-int-gpio = <0>,"+85+101", <&sx150x_1_3F_pins>,"brcm,pins:0", <&sx1509_1_3F>,"interrupts:0"; ++ sx1509-0-70-int-gpio = <0>,"+86+102", <&sx150x_0_70_pins>,"brcm,pins:0", <&sx1509_0_70>,"interrupts:0"; ++ sx1509-1-70-int-gpio = <0>,"+87+103", <&sx150x_1_70_pins>,"brcm,pins:0", <&sx1509_1_70>,"interrupts:0"; ++ sx1509-0-71-int-gpio = <0>,"+88+104", <&sx150x_0_71_pins>,"brcm,pins:0", <&sx1509_0_71>,"interrupts:0"; ++ sx1509-1-71-int-gpio = <0>,"+89+105", <&sx150x_1_71_pins>,"brcm,pins:0", <&sx1509_1_71>,"interrupts:0"; ++ }; ++}; ++ +diff --git a/arch/arm/boot/dts/overlays/tc358743-audio-overlay.dts b/arch/arm/boot/dts/overlays/tc358743-audio-overlay.dts +new file mode 100644 +index 000000000000..047695bb0c71 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/tc358743-audio-overlay.dts +@@ -0,0 +1,52 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Definitions to add I2S audio from the Toshiba TC358743 HDMI to CSI2 bridge. ++// Requires tc358743 overlay to have been loaded to actually function. ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ tc358743_codec: tc358743-codec { ++ #sound-dai-cells = <0>; ++ compatible = "linux,spdif-dir"; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&sound>; ++ sound_overlay: __overlay__ { ++ compatible = "simple-audio-card"; ++ simple-audio-card,format = "i2s"; ++ simple-audio-card,name = "tc358743"; ++ simple-audio-card,bitclock-master = <&dailink0_slave>; ++ simple-audio-card,frame-master = <&dailink0_slave>; ++ status = "okay"; ++ ++ simple-audio-card,cpu { ++ sound-dai = <&i2s>; ++ dai-tdm-slot-num = <2>; ++ dai-tdm-slot-width = <32>; ++ }; ++ dailink0_slave: simple-audio-card,codec { ++ sound-dai = <&tc358743_codec>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ card-name = <&sound_overlay>,"simple-audio-card,name"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/tc358743-overlay.dts b/arch/arm/boot/dts/overlays/tc358743-overlay.dts +new file mode 100644 +index 000000000000..a1f8af36d2e7 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/tc358743-overlay.dts +@@ -0,0 +1,107 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++// Definitions for Toshiba TC358743 HDMI to CSI2 bridge on VC I2C bus ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&i2c_csi_dsi>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ ++ tc358743@0f { ++ compatible = "toshiba,tc358743"; ++ reg = <0x0f>; ++ status = "okay"; ++ ++ clocks = <&tc358743_clk>; ++ clock-names = "refclk"; ++ ++ port { ++ tc358743: endpoint { ++ remote-endpoint = <&csi1_ep>; ++ clock-lanes = <0>; ++ clock-noncontinuous; ++ link-frequencies = ++ /bits/ 64 <486000000>; ++ }; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&csi1>; ++ __overlay__ { ++ status = "okay"; ++ ++ port { ++ csi1_ep: endpoint { ++ remote-endpoint = <&tc358743>; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&tc358743>; ++ __overlay__ { ++ data-lanes = <1 2>; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&tc358743>; ++ __dormant__ { ++ data-lanes = <1 2 3 4>; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&i2c0if>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&i2c0mux>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@6 { ++ target-path = "/"; ++ __overlay__ { ++ tc358743_clk: bridge-clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <27000000>; ++ }; ++ }; ++ }; ++ ++ fragment@7 { ++ target = <&csi1_ep>; ++ __overlay__ { ++ data-lanes = <1 2>; ++ }; ++ }; ++ ++ fragment@8 { ++ target = <&csi1_ep>; ++ __dormant__ { ++ data-lanes = <1 2 3 4>; ++ }; ++ }; ++ ++ __overrides__ { ++ 4lane = <0>, "-2+3-7+8"; ++ link-frequency = <&tc358743>,"link-frequencies#0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/tinylcd35-overlay.dts b/arch/arm/boot/dts/overlays/tinylcd35-overlay.dts +new file mode 100644 +index 000000000000..a102b09e3ab5 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/tinylcd35-overlay.dts +@@ -0,0 +1,222 @@ ++/* ++ * tinylcd35-overlay.dts ++ * ++ * ------------------------------------------------- ++ * www.tinlylcd.com ++ * ------------------------------------------------- ++ * Device---Driver-----BUS GPIO's ++ * display tinylcd35 spi0.0 25 24 18 ++ * touch ads7846 spi0.1 5 ++ * rtc ds1307 i2c1-0068 ++ * rtc pcf8563 i2c1-0051 ++ * keypad gpio-keys --------- 17 22 27 23 28 ++ * ++ * ++ * TinyLCD.com 3.5 inch TFT ++ * ++ * Version 001 ++ * 5/3/2015 -- Noralf Trønnes Initial Device tree framework ++ * 10/3/2015 -- tinylcd@gmail.com added ds1307 support. ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ tinylcd35_pins: tinylcd35_pins { ++ brcm,pins = <25 24 18>; ++ brcm,function = <1>; /* out */ ++ }; ++ tinylcd35_ts_pins: tinylcd35_ts_pins { ++ brcm,pins = <5>; ++ brcm,function = <0>; /* in */ ++ }; ++ keypad_pins: keypad_pins { ++ brcm,pins = <4 17 22 23 27>; ++ brcm,function = <0>; /* in */ ++ brcm,pull = <1>; /* down */ ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ tinylcd35: tinylcd35@0{ ++ compatible = "neosec,tinylcd"; ++ reg = <0>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&tinylcd35_pins>, ++ <&tinylcd35_ts_pins>; ++ ++ spi-max-frequency = <48000000>; ++ rotate = <270>; ++ fps = <20>; ++ bgr; ++ buswidth = <8>; ++ reset-gpios = <&gpio 25 1>; ++ dc-gpios = <&gpio 24 0>; ++ led-gpios = <&gpio 18 0>; ++ debug = <0>; ++ ++ init = <0x10000B0 0x80 ++ 0x10000C0 0x0A 0x0A ++ 0x10000C1 0x01 0x01 ++ 0x10000C2 0x33 ++ 0x10000C5 0x00 0x42 0x80 ++ 0x10000B1 0xD0 0x11 ++ 0x10000B4 0x02 ++ 0x10000B6 0x00 0x22 0x3B ++ 0x10000B7 0x07 ++ 0x1000036 0x58 ++ 0x10000F0 0x36 0xA5 0xD3 ++ 0x10000E5 0x80 ++ 0x10000E5 0x01 ++ 0x10000B3 0x00 ++ 0x10000E5 0x00 ++ 0x10000F0 0x36 0xA5 0x53 ++ 0x10000E0 0x00 0x35 0x33 0x00 0x00 0x00 0x00 0x35 0x33 0x00 0x00 0x00 ++ 0x100003A 0x55 ++ 0x1000011 ++ 0x2000001 ++ 0x1000029>; ++ }; ++ ++ tinylcd35_ts: tinylcd35_ts@1 { ++ compatible = "ti,ads7846"; ++ reg = <1>; ++ status = "disabled"; ++ ++ spi-max-frequency = <2000000>; ++ interrupts = <5 2>; /* high-to-low edge triggered */ ++ interrupt-parent = <&gpio>; ++ pendown-gpio = <&gpio 5 0>; ++ ti,x-plate-ohms = /bits/ 16 <100>; ++ ti,pressure-max = /bits/ 16 <255>; ++ }; ++ }; ++ }; ++ ++ /* RTC */ ++ ++ fragment@5 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ pcf8563: pcf8563@51 { ++ compatible = "nxp,pcf8563"; ++ reg = <0x51>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&i2c1>; ++ __dormant__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ ds1307: ds1307@68 { ++ compatible = "dallas,ds1307"; ++ reg = <0x68>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ /* ++ * Values for input event code is found under the ++ * 'Keys and buttons' heading in include/uapi/linux/input.h ++ */ ++ fragment@7 { ++ target-path = "/soc"; ++ __overlay__ { ++ keypad: keypad { ++ compatible = "gpio-keys"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&keypad_pins>; ++ status = "disabled"; ++ autorepeat; ++ ++ button@17 { ++ label = "GPIO KEY_UP"; ++ linux,code = <103>; ++ gpios = <&gpio 17 0>; ++ }; ++ button@22 { ++ label = "GPIO KEY_DOWN"; ++ linux,code = <108>; ++ gpios = <&gpio 22 0>; ++ }; ++ button@27 { ++ label = "GPIO KEY_LEFT"; ++ linux,code = <105>; ++ gpios = <&gpio 27 0>; ++ }; ++ button@23 { ++ label = "GPIO KEY_RIGHT"; ++ linux,code = <106>; ++ gpios = <&gpio 23 0>; ++ }; ++ button@4 { ++ label = "GPIO KEY_ENTER"; ++ linux,code = <28>; ++ gpios = <&gpio 4 0>; ++ }; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ speed = <&tinylcd35>,"spi-max-frequency:0"; ++ rotate = <&tinylcd35>,"rotate:0"; ++ fps = <&tinylcd35>,"fps:0"; ++ debug = <&tinylcd35>,"debug:0"; ++ touch = <&tinylcd35_ts>,"status"; ++ touchgpio = <&tinylcd35_ts_pins>,"brcm,pins:0", ++ <&tinylcd35_ts>,"interrupts:0", ++ <&tinylcd35_ts>,"pendown-gpio:4"; ++ xohms = <&tinylcd35_ts>,"ti,x-plate-ohms;0"; ++ rtc-pcf = <0>,"=5"; ++ rtc-ds = <0>,"=6"; ++ keypad = <&keypad>,"status"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/tpm-slb9670-overlay.dts b/arch/arm/boot/dts/overlays/tpm-slb9670-overlay.dts +new file mode 100644 +index 000000000000..e69188503ca3 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/tpm-slb9670-overlay.dts +@@ -0,0 +1,44 @@ ++/* ++ * Device Tree overlay for the Infineon SLB9670 Trusted Platform Module add-on ++ * boards, which can be used as a secure key storage and hwrng. ++ * available as "Iridium SLB9670" by Infineon and "LetsTrust TPM" by pi3g. ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev1>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ slb9670: slb9670@1 { ++ compatible = "infineon,slb9670"; ++ reg = <1>; /* CE1 */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ spi-max-frequency = <32000000>; ++ status = "okay"; ++ }; ++ ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/uart0-overlay.dts b/arch/arm/boot/dts/overlays/uart0-overlay.dts +new file mode 100755 +index 000000000000..73d563bbaabf +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/uart0-overlay.dts +@@ -0,0 +1,32 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&uart0>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart0_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ uart0_pins: uart0_pins { ++ brcm,pins = <14 15>; ++ brcm,function = <4>; /* alt0 */ ++ brcm,pull = <0 2>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ txd0_pin = <&uart0_pins>,"brcm,pins:0"; ++ rxd0_pin = <&uart0_pins>,"brcm,pins:4"; ++ pin_func = <&uart0_pins>,"brcm,function:0"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/uart1-overlay.dts b/arch/arm/boot/dts/overlays/uart1-overlay.dts +new file mode 100644 +index 000000000000..986d725a2652 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/uart1-overlay.dts +@@ -0,0 +1,38 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&uart1>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart1_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ uart1_pins: uart1_pins { ++ brcm,pins = <14 15>; ++ brcm,function = <2>; /* alt5 */ ++ brcm,pull = <0 2>; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target-path = "/chosen"; ++ __overlay__ { ++ bootargs = "8250.nr_uarts=1"; ++ }; ++ }; ++ ++ __overrides__ { ++ txd1_pin = <&uart1_pins>,"brcm,pins:0"; ++ rxd1_pin = <&uart1_pins>,"brcm,pins:4"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/uart2-overlay.dts b/arch/arm/boot/dts/overlays/uart2-overlay.dts +new file mode 100644 +index 000000000000..9face240aca1 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/uart2-overlay.dts +@@ -0,0 +1,27 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&uart2>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart2_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&uart2_pins>; ++ __dormant__ { ++ brcm,pins = <0 1 2 3>; ++ brcm,pull = <0 2 2 0>; ++ }; ++ }; ++ ++ __overrides__ { ++ ctsrts = <0>,"=1"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/uart3-overlay.dts b/arch/arm/boot/dts/overlays/uart3-overlay.dts +new file mode 100644 +index 000000000000..ae9f9fe5ea1d +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/uart3-overlay.dts +@@ -0,0 +1,27 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&uart3>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart3_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&uart3_pins>; ++ __dormant__ { ++ brcm,pins = <4 5 6 7>; ++ brcm,pull = <0 2 2 0>; ++ }; ++ }; ++ ++ __overrides__ { ++ ctsrts = <0>,"=1"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/uart4-overlay.dts b/arch/arm/boot/dts/overlays/uart4-overlay.dts +new file mode 100644 +index 000000000000..ac004ffbadbf +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/uart4-overlay.dts +@@ -0,0 +1,27 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&uart4>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart4_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&uart4_pins>; ++ __dormant__ { ++ brcm,pins = <8 9 10 11>; ++ brcm,pull = <0 2 2 0>; ++ }; ++ }; ++ ++ __overrides__ { ++ ctsrts = <0>,"=1"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/uart5-overlay.dts b/arch/arm/boot/dts/overlays/uart5-overlay.dts +new file mode 100644 +index 000000000000..04eaf376effe +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/uart5-overlay.dts +@@ -0,0 +1,27 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2711"; ++ ++ fragment@0 { ++ target = <&uart5>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&uart5_pins>; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&uart5_pins>; ++ __dormant__ { ++ brcm,pins = <12 13 14 15>; ++ brcm,pull = <0 2 2 0>; ++ }; ++ }; ++ ++ __overrides__ { ++ ctsrts = <0>,"=1"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/udrc-overlay.dts b/arch/arm/boot/dts/overlays/udrc-overlay.dts +new file mode 100644 +index 000000000000..ae7c37996894 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/udrc-overlay.dts +@@ -0,0 +1,128 @@ ++#include ++/* ++ * Device tree overlay for the Universal Digital Radio Controller ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ fragment@0 { ++ target = <&i2s>; ++ __overlay__ { ++ clocks = <&clocks BCM2835_CLOCK_PCM>; ++ clock-names = "pcm"; ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@1 { ++ target-path = "/"; ++ __overlay__ { ++ regulators { ++ compatible = "simple-bus"; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ udrc0_ldoin: udrc0_ldoin { ++ compatible = "regulator-fixed"; ++ regulator-name = "ldoin"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ regulator-always-on; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ status = "okay"; ++ clocks = <&clocks BCM2835_CLOCK_VPU>; ++ clock-frequency = <400000>; ++ ++ tlv320aic32x4: tlv320aic32x4@18 { ++ compatible = "ti,tlv320aic32x4"; ++ #sound-dai-cells = <0>; ++ reg = <0x18>; ++ status = "okay"; ++ ++ clocks = <&clocks BCM2835_CLOCK_GP0>; ++ clock-names = "mclk"; ++ assigned-clocks = <&clocks BCM2835_CLOCK_GP0>; ++ assigned-clock-rates = <25000000>; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&gpclk0_pin &aic3204_reset>; ++ ++ reset-gpios = <&gpio 13 0>; ++ ++ iov-supply = <&udrc0_ldoin>; ++ ldoin-supply = <&udrc0_ldoin>; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&sound>; ++ snd: __overlay__ { ++ compatible = "simple-audio-card"; ++ i2s-controller = <&i2s>; ++ status = "okay"; ++ ++ simple-audio-card,name = "udrc"; ++ simple-audio-card,format = "i2s"; ++ ++ simple-audio-card,bitclock-master = <&dailink0_master>; ++ simple-audio-card,frame-master = <&dailink0_master>; ++ ++ simple-audio-card,widgets = ++ "Line", "Line In", ++ "Line", "Line Out"; ++ ++ simple-audio-card,routing = ++ "IN1_R", "Line In", ++ "IN1_L", "Line In", ++ "CM_L", "Line In", ++ "CM_R", "Line In", ++ "Line Out", "LOR", ++ "Line Out", "LOL"; ++ ++ dailink0_master: simple-audio-card,cpu { ++ sound-dai = <&i2s>; ++ }; ++ ++ simple-audio-card,codec { ++ sound-dai = <&tlv320aic32x4>; ++ }; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&gpio>; ++ __overlay__ { ++ gpclk0_pin: gpclk0_pin { ++ brcm,pins = <4>; ++ brcm,function = <4>; ++ }; ++ ++ aic3204_reset: aic3204_reset { ++ brcm,pins = <13>; ++ brcm,function = <1>; ++ brcm,pull = <1>; ++ }; ++ ++ aic3204_gpio: aic3204_gpio { ++ brcm,pins = <26>; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ alsaname = <&snd>, "simple-audio-card,name"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/upstream-overlay.dts b/arch/arm/boot/dts/overlays/upstream-overlay.dts +new file mode 100644 +index 000000000000..2e9dcd4f5f0a +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/upstream-overlay.dts +@@ -0,0 +1,113 @@ ++// redo: ovmerge -c vc4-kms-v3d-overlay.dts,cma-default dwc2-overlay.dts,dr_mode=otg ++ ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ fragment@0 { ++ target = <&cma>; ++ __dormant__ { ++ size = <0x10000000>; ++ }; ++ }; ++ fragment@1 { ++ target = <&i2c2>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@2 { ++ target = <&fb>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ fragment@3 { ++ target = <&pixelvalve0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@4 { ++ target = <&pixelvalve1>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@5 { ++ target = <&pixelvalve2>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@6 { ++ target = <&hvs>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@7 { ++ target = <&hdmi>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@8 { ++ target = <&v3d>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@9 { ++ target = <&vc4>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@10 { ++ target = <&clocks>; ++ __overlay__ { ++ claim-clocks = ; ++ }; ++ }; ++ fragment@11 { ++ target = <&vec>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@12 { ++ target = <&txp>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@13 { ++ target = <&hdmi>; ++ __dormant__ { ++ dmas; ++ }; ++ }; ++ fragment@14 { ++ target = <&audio>; ++ __overlay__ { ++ brcm,disable-hdmi; ++ }; ++ }; ++ fragment@15 { ++ target = <&usb>; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ __overlay__ { ++ compatible = "brcm,bcm2835-usb"; ++ dr_mode = "otg"; ++ g-np-tx-fifo-size = <32>; ++ g-rx-fifo-size = <558>; ++ g-tx-fifo-size = <512 512 512 512 512 256 256>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/upstream-pi4-overlay.dts b/arch/arm/boot/dts/overlays/upstream-pi4-overlay.dts +new file mode 100644 +index 000000000000..6195e02bf9ff +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/upstream-pi4-overlay.dts +@@ -0,0 +1,161 @@ ++// redo: ovmerge -c vc4-kms-v3d-pi4-overlay.dts,cma-default dwc2-overlay.dts,dr_mode=otg ++ ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ fragment@0 { ++ target = <&cma>; ++ __dormant__ { ++ size = <0x10000000>; ++ }; ++ }; ++ fragment@1 { ++ target = <&ddc0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@2 { ++ target = <&ddc1>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@3 { ++ target = <&hdmi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@4 { ++ target = <&hdmi1>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@5 { ++ target = <&hvs>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@6 { ++ target = <&pixelvalve0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@7 { ++ target = <&pixelvalve1>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@8 { ++ target = <&pixelvalve2>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@9 { ++ target = <&pixelvalve3>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@10 { ++ target = <&pixelvalve4>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@11 { ++ target = <&v3d>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@12 { ++ target = <&vc4>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@13 { ++ target = <&txp>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@14 { ++ target = <&fb>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ fragment@15 { ++ target = <&firmwarekms>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ fragment@16 { ++ target = <&vec>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ fragment@17 { ++ target = <&hdmi0>; ++ __dormant__ { ++ dmas; ++ }; ++ }; ++ fragment@18 { ++ target = <&hdmi1>; ++ __dormant__ { ++ dmas; ++ }; ++ }; ++ fragment@19 { ++ target = <&audio>; ++ __overlay__ { ++ brcm,disable-hdmi; ++ }; ++ }; ++ fragment@20 { ++ target = <&dvp>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@21 { ++ target = <&pixelvalve3>; ++ __dormant__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@22 { ++ target = <&vec>; ++ __dormant__ { ++ status = "okay"; ++ }; ++ }; ++ fragment@23 { ++ target = <&usb>; ++ #address-cells = <1>; ++ #size-cells = <1>; ++ __overlay__ { ++ compatible = "brcm,bcm2835-usb"; ++ dr_mode = "otg"; ++ g-np-tx-fifo-size = <32>; ++ g-rx-fifo-size = <558>; ++ g-tx-fifo-size = <512 512 512 512 512 256 256>; ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/vc4-fkms-v3d-overlay.dts b/arch/arm/boot/dts/overlays/vc4-fkms-v3d-overlay.dts +new file mode 100644 +index 000000000000..ca344492bed8 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/vc4-fkms-v3d-overlay.dts +@@ -0,0 +1,40 @@ ++/* ++ * vc4-fkms-v3d-overlay.dts ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++#include "cma-overlay.dts" ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@1 { ++ target = <&fb>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&firmwarekms>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&v3d>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&vc4>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/vc4-kms-kippah-7inch-overlay.dts b/arch/arm/boot/dts/overlays/vc4-kms-kippah-7inch-overlay.dts +new file mode 100644 +index 000000000000..b03394844abd +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/vc4-kms-kippah-7inch-overlay.dts +@@ -0,0 +1,43 @@ ++/* ++ * vc4-kms-v3d-overlay.dts ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ panel: panel { ++ compatible = "ontat,yx700wv03", "simple-panel"; ++ ++ port { ++ panel_in: endpoint { ++ remote-endpoint = <&dpi_out>; ++ }; ++ }; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&dpi>; ++ __overlay__ { ++ status = "okay"; ++ ++ pinctrl-names = "default"; ++ pinctrl-0 = <&dpi_18bit_gpio0>; ++ ++ port { ++ dpi_out: endpoint@0 { ++ remote-endpoint = <&panel_in>; ++ }; ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts b/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts +new file mode 100644 +index 000000000000..6d34a2bff49b +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/vc4-kms-v3d-overlay.dts +@@ -0,0 +1,122 @@ ++/* ++ * vc4-kms-v3d-overlay.dts ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++#include "cma-overlay.dts" ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@1 { ++ target = <&i2c2>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&fb>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&pixelvalve0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&pixelvalve1>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&pixelvalve2>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&hvs>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@7 { ++ target = <&hdmi>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@8 { ++ target = <&v3d>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@9 { ++ target = <&vc4>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@10 { ++ target = <&clocks>; ++ __overlay__ { ++ claim-clocks = < ++ BCM2835_PLLD_DSI0 ++ BCM2835_PLLD_DSI1 ++ BCM2835_PLLH_AUX ++ BCM2835_PLLH_PIX ++ >; ++ }; ++ }; ++ ++ fragment@11 { ++ target = <&vec>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@12 { ++ target = <&txp>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@13 { ++ target = <&hdmi>; ++ __dormant__ { ++ dmas; ++ }; ++ }; ++ ++ fragment@14 { ++ target = <&audio>; ++ __overlay__ { ++ brcm,disable-hdmi; ++ }; ++ }; ++ ++ __overrides__ { ++ audio = <0>,"!13", <0>,"=14"; ++ noaudio = <0>,"=13", <0>,"!14"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/vc4-kms-v3d-pi4-overlay.dts b/arch/arm/boot/dts/overlays/vc4-kms-v3d-pi4-overlay.dts +new file mode 100644 +index 000000000000..f721f12d729d +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/vc4-kms-v3d-pi4-overlay.dts +@@ -0,0 +1,186 @@ ++/* ++ * vc4-kms-v3d-pi4-overlay.dts ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++#include ++ ++#include "cma-overlay.dts" ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@1 { ++ target = <&ddc0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&ddc1>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&hdmi0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@4 { ++ target = <&hdmi1>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@5 { ++ target = <&hvs>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@6 { ++ target = <&pixelvalve0>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@7 { ++ target = <&pixelvalve1>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@8 { ++ target = <&pixelvalve2>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@9 { ++ target = <&pixelvalve3>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@10 { ++ target = <&pixelvalve4>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@11 { ++ target = <&v3d>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@12 { ++ target = <&vc4>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@13 { ++ target = <&txp>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@14 { ++ target = <&fb>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@15 { ++ target = <&firmwarekms>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@16 { ++ target = <&vec>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@17 { ++ target = <&hdmi0>; ++ __dormant__ { ++ dmas; ++ }; ++ }; ++ ++ fragment@18 { ++ target = <&hdmi1>; ++ __dormant__ { ++ dmas; ++ }; ++ }; ++ ++ fragment@19 { ++ target = <&audio>; ++ __overlay__ { ++ brcm,disable-hdmi; ++ }; ++ }; ++ ++ fragment@20 { ++ target = <&dvp>; ++ __overlay__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@21 { ++ target = <&pixelvalve3>; ++ __dormant__ { ++ status = "okay"; ++ }; ++ }; ++ ++ fragment@22 { ++ target = <&vec>; ++ __dormant__ { ++ status = "okay"; ++ }; ++ }; ++ ++ __overrides__ { ++ audio = <0>,"!17"; ++ audio1 = <0>,"!18"; ++ noaudio = <0>,"=17", <0>,"=18", <0>,"!19"; ++ composite = <0>, "!1", ++ <0>, "!2", ++ <0>, "!3", ++ <0>, "!4", ++ <0>, "!6", ++ <0>, "!7", ++ <0>, "!8", ++ <0>, "!9", ++ <0>, "!10", ++ <0>, "!16", ++ <0>, "=21", ++ <0>, "=22"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/vga666-overlay.dts b/arch/arm/boot/dts/overlays/vga666-overlay.dts +new file mode 100644 +index 000000000000..a4968d180a5d +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/vga666-overlay.dts +@@ -0,0 +1,30 @@ ++/dts-v1/; ++/plugin/; ++ ++/{ ++ compatible = "brcm,bcm2835"; ++ ++ // There is no VGA driver module, but we need a platform device ++ // node (that doesn't already use pinctrl) to hang the pinctrl ++ // reference on - leds will do ++ ++ fragment@0 { ++ target = <&leds>; ++ __overlay__ { ++ pinctrl-names = "default"; ++ pinctrl-0 = <&vga666_pins>; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ vga666_pins: vga666_pins { ++ brcm,pins = <2 3 4 5 6 7 8 9 10 11 12 ++ 13 14 15 16 17 18 19 20 21>; ++ brcm,function = <6>; /* alt2 */ ++ brcm,pull = <0>; /* no pull */ ++ }; ++ }; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/w1-gpio-overlay.dts b/arch/arm/boot/dts/overlays/w1-gpio-overlay.dts +new file mode 100644 +index 000000000000..f44e325bc1f2 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/w1-gpio-overlay.dts +@@ -0,0 +1,40 @@ ++// Definitions for w1-gpio module (without external pullup) ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ ++ w1: onewire@0 { ++ compatible = "w1-gpio"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&w1_pins>; ++ gpios = <&gpio 4 0>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ w1_pins: w1_pins@0 { ++ brcm,pins = <4>; ++ brcm,function = <0>; // in (initially) ++ brcm,pull = <0>; // off ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpiopin = <&w1>,"gpios:4", ++ <&w1>,"reg:0", ++ <&w1_pins>,"brcm,pins:0", ++ <&w1_pins>,"reg:0"; ++ pullup; // Silently ignore unneeded parameter ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/w1-gpio-pullup-overlay.dts b/arch/arm/boot/dts/overlays/w1-gpio-pullup-overlay.dts +new file mode 100644 +index 000000000000..953c6a1aeab9 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/w1-gpio-pullup-overlay.dts +@@ -0,0 +1,42 @@ ++// Definitions for w1-gpio module (with external pullup) ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target-path = "/"; ++ __overlay__ { ++ ++ w1: onewire@0 { ++ compatible = "w1-gpio"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&w1_pins>; ++ gpios = <&gpio 4 0>, <&gpio 5 1>; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&gpio>; ++ __overlay__ { ++ w1_pins: w1_pins@0 { ++ brcm,pins = <4 5>; ++ brcm,function = <0 1>; // in out ++ brcm,pull = <0 0>; // off off ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ gpiopin = <&w1>,"gpios:4", ++ <&w1>,"reg:0", ++ <&w1_pins>,"brcm,pins:0", ++ <&w1_pins>,"reg:0"; ++ extpullup = <&w1>,"gpios:16", ++ <&w1_pins>,"brcm,pins:4"; ++ pullup; // Silently ignore unneeded parameter ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/w5500-overlay.dts b/arch/arm/boot/dts/overlays/w5500-overlay.dts +new file mode 100644 +index 000000000000..4d3e66296753 +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/w5500-overlay.dts +@@ -0,0 +1,63 @@ ++// Overlay for the Wiznet w5500 Ethernet Controller ++/dts-v1/; ++/plugin/; ++ ++/ { ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&spidev0>; ++ __overlay__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&spidev1>; ++ __dormant__ { ++ status = "disabled"; ++ }; ++ }; ++ ++ fragment@2 { ++ target = <&spi0>; ++ __overlay__ { ++ /* needed to avoid dtc warning */ ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ status = "okay"; ++ ++ eth1: w5500@0{ ++ compatible = "wiznet,w5500"; ++ reg = <0>; /* CE0 */ ++ pinctrl-names = "default"; ++ pinctrl-0 = <ð1_pins>; ++ interrupt-parent = <&gpio>; ++ interrupts = <25 0x8>; ++ spi-max-frequency = <30000000>; ++// local-mac-address = [aa bb cc dd ee ff]; ++ status = "okay"; ++ }; ++ }; ++ }; ++ ++ fragment@3 { ++ target = <&gpio>; ++ __overlay__ { ++ eth1_pins: eth1_pins { ++ brcm,pins = <25>; ++ brcm,function = <0>; /* in */ ++ brcm,pull = <0>; /* none */ ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ int_pin = <ð1>, "interrupts:0", ++ <ð1_pins>, "brcm,pins:0"; ++ speed = <ð1>, "spi-max-frequency:0"; ++ cs = <ð1>, "reg:0", ++ <0>, "!0=1"; ++ }; ++}; +diff --git a/arch/arm/boot/dts/overlays/wittypi-overlay.dts b/arch/arm/boot/dts/overlays/wittypi-overlay.dts +new file mode 100644 +index 000000000000..71ce806186de +--- /dev/null ++++ b/arch/arm/boot/dts/overlays/wittypi-overlay.dts +@@ -0,0 +1,44 @@ ++/* ++ * Device Tree overlay for Witty Pi extension board by UUGear ++ * ++ */ ++ ++/dts-v1/; ++/plugin/; ++ ++/ { ++ ++ compatible = "brcm,bcm2835"; ++ ++ fragment@0 { ++ target = <&leds>; ++ __overlay__ { ++ compatible = "gpio-leds"; ++ wittypi_led: wittypi_led { ++ label = "wittypi_led"; ++ linux,default-trigger = "default-on"; ++ gpios = <&gpio 17 0>; ++ }; ++ }; ++ }; ++ ++ fragment@1 { ++ target = <&i2c1>; ++ __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ rtc: ds1337@68 { ++ compatible = "dallas,ds1337"; ++ reg = <0x68>; ++ wakeup-source; ++ }; ++ }; ++ }; ++ ++ __overrides__ { ++ led_gpio = <&wittypi_led>,"gpios:4"; ++ led_trigger = <&wittypi_led>,"linux,default-trigger"; ++ }; ++ ++}; +diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile +index 9b1170658d60..cc6c25629057 100644 +--- a/arch/arm64/boot/dts/Makefile ++++ b/arch/arm64/boot/dts/Makefile +@@ -30,3 +30,5 @@ subdir-y += ti + subdir-y += toshiba + subdir-y += xilinx + subdir-y += zte ++ ++subdir-y += overlays +diff --git a/arch/arm64/boot/dts/broadcom/Makefile b/arch/arm64/boot/dts/broadcom/Makefile +index cb7de8d99223..c3eaf8d63ee4 100644 +--- a/arch/arm64/boot/dts/broadcom/Makefile ++++ b/arch/arm64/boot/dts/broadcom/Makefile +@@ -1,9 +1,21 @@ + # SPDX-License-Identifier: GPL-2.0 +-dtb-$(CONFIG_ARCH_BCM2835) += bcm2711-rpi-4-b.dtb \ +- bcm2837-rpi-3-a-plus.dtb \ ++dtb-$(CONFIG_ARCH_BCM2835) += bcm2837-rpi-3-a-plus.dtb \ + bcm2837-rpi-3-b.dtb \ + bcm2837-rpi-3-b-plus.dtb \ + bcm2837-rpi-cm3-io3.dtb ++dtb-$(CONFIG_ARCH_BCM2709) += bcm2710-rpi-2-b.dtb ++dtb-$(CONFIG_ARCH_BCM2709) += bcm2710-rpi-3-b.dtb ++dtb-$(CONFIG_ARCH_BCM2835) += bcm2710-rpi-2-b.dtb ++dtb-$(CONFIG_ARCH_BCM2835) += bcm2710-rpi-3-b.dtb ++dtb-$(CONFIG_ARCH_BCM2835) += bcm2711-rpi-4-b.dtb ++dtb-$(CONFIG_ARCH_BCM2835) += bcm2710-rpi-3-b-plus.dtb ++dtb-$(CONFIG_ARCH_BCM2709) += bcm2710-rpi-cm3.dtb ++dtb-$(CONFIG_ARCH_BCM2835) += bcm2710-rpi-cm3.dtb + + subdir-y += northstar2 + subdir-y += stingray ++ ++# Enable fixups to support overlays on BCM2835 platforms ++ifeq ($(CONFIG_ARCH_BCM2835),y) ++ DTC_FLAGS ?= -@ ++endif +diff --git a/arch/arm64/boot/dts/broadcom/bcm2710-rpi-2-b.dts b/arch/arm64/boot/dts/broadcom/bcm2710-rpi-2-b.dts +new file mode 100644 +index 000000000000..116cdbf94b9b +--- /dev/null ++++ b/arch/arm64/boot/dts/broadcom/bcm2710-rpi-2-b.dts +@@ -0,0 +1,3 @@ ++#define RPI364 ++ ++#include "../../../../arm/boot/dts/bcm2710-rpi-2-b.dts" +diff --git a/arch/arm64/boot/dts/broadcom/bcm2710-rpi-3-b-plus.dts b/arch/arm64/boot/dts/broadcom/bcm2710-rpi-3-b-plus.dts +new file mode 100644 +index 000000000000..d9242ff77079 +--- /dev/null ++++ b/arch/arm64/boot/dts/broadcom/bcm2710-rpi-3-b-plus.dts +@@ -0,0 +1,3 @@ ++#define RPI364 ++ ++#include "../../../../arm/boot/dts/bcm2710-rpi-3-b-plus.dts" +diff --git a/arch/arm64/boot/dts/broadcom/bcm2710-rpi-3-b.dts b/arch/arm64/boot/dts/broadcom/bcm2710-rpi-3-b.dts +new file mode 100644 +index 000000000000..deb33441da95 +--- /dev/null ++++ b/arch/arm64/boot/dts/broadcom/bcm2710-rpi-3-b.dts +@@ -0,0 +1,3 @@ ++#define RPI364 ++ ++#include "../../../../arm/boot/dts/bcm2710-rpi-3-b.dts" +diff --git a/arch/arm64/boot/dts/broadcom/bcm2710-rpi-cm3.dts b/arch/arm64/boot/dts/broadcom/bcm2710-rpi-cm3.dts +new file mode 100644 +index 000000000000..1c2560017c02 +--- /dev/null ++++ b/arch/arm64/boot/dts/broadcom/bcm2710-rpi-cm3.dts +@@ -0,0 +1,3 @@ ++#define RPI364 ++ ++#include "../../../../arm/boot/dts/bcm2710-rpi-cm3.dts" +diff --git a/arch/arm64/boot/dts/broadcom/bcm2711-rpi-4-b.dts b/arch/arm64/boot/dts/broadcom/bcm2711-rpi-4-b.dts +index d24c53682e44..1fd86f81f542 100644 +--- a/arch/arm64/boot/dts/broadcom/bcm2711-rpi-4-b.dts ++++ b/arch/arm64/boot/dts/broadcom/bcm2711-rpi-4-b.dts +@@ -1,2 +1,3 @@ +-// SPDX-License-Identifier: GPL-2.0 +-#include "arm/bcm2711-rpi-4-b.dts" ++#define RPI364 ++ ++#include "../../../../arm/boot/dts/bcm2711-rpi-4-b.dts" +diff --git a/arch/arm64/boot/dts/broadcom/bcm283x-rpi-csi1-2lane.dtsi b/arch/arm64/boot/dts/broadcom/bcm283x-rpi-csi1-2lane.dtsi +new file mode 120000 +index 000000000000..e5c400284467 +--- /dev/null ++++ b/arch/arm64/boot/dts/broadcom/bcm283x-rpi-csi1-2lane.dtsi +@@ -0,0 +1 @@ ++../../../../arm/boot/dts/bcm283x-rpi-csi1-2lane.dtsi +\ No newline at end of file +diff --git a/arch/arm64/boot/dts/broadcom/bcm283x-rpi-lan7515.dtsi b/arch/arm64/boot/dts/broadcom/bcm283x-rpi-lan7515.dtsi +new file mode 120000 +index 000000000000..fc4c05bbe7fd +--- /dev/null ++++ b/arch/arm64/boot/dts/broadcom/bcm283x-rpi-lan7515.dtsi +@@ -0,0 +1 @@ ++../../../../arm/boot/dts/bcm283x-rpi-lan7515.dtsi +\ No newline at end of file +diff --git a/arch/arm64/boot/dts/overlays b/arch/arm64/boot/dts/overlays +new file mode 120000 +index 000000000000..ded08646b6f6 +--- /dev/null ++++ b/arch/arm64/boot/dts/overlays +@@ -0,0 +1 @@ ++../../../arm/boot/dts/overlays +\ No newline at end of file +diff --git a/scripts/Makefile.dtbinst b/scripts/Makefile.dtbinst +index 50d580d77ae9..079b83308011 100644 +--- a/scripts/Makefile.dtbinst ++++ b/scripts/Makefile.dtbinst +@@ -18,9 +18,10 @@ include scripts/Kbuild.include + include $(src)/Makefile + + dtbs := $(addprefix $(dst)/, $(dtb-y) $(if $(CONFIG_OF_ALL_DTBS),$(dtb-))) ++dtbos := $(addprefix $(dst)/, $(dtbo-y) $(if $(CONFIG_OF_ALL_DTBS),$(dtb-))) + subdirs := $(addprefix $(obj)/, $(subdir-y) $(subdir-m)) + +-__dtbs_install: $(dtbs) $(subdirs) ++__dtbs_install: $(dtbs) $(dtbos) $(subdirs) + @: + + quiet_cmd_dtb_install = INSTALL $@ +@@ -29,6 +30,9 @@ quiet_cmd_dtb_install = INSTALL $@ + $(dst)/%.dtb: $(obj)/%.dtb + $(call cmd,dtb_install) + ++$(dst)/%.dtbo: $(obj)/%.dtbo ++ $(call cmd,dtb_install) ++ + PHONY += $(subdirs) + $(subdirs): + $(Q)$(MAKE) $(dtbinst)=$@ dst=$(patsubst $(obj)/%,$(dst)/%,$@) +diff --git a/scripts/Makefile.lib b/scripts/Makefile.lib +index 94133708889d..9c0df5bde46c 100644 +--- a/scripts/Makefile.lib ++++ b/scripts/Makefile.lib +@@ -281,6 +281,7 @@ DTC_FLAGS += -Wno-interrupt_provider + ifeq ($(findstring 1,$(KBUILD_EXTRA_WARN)),) + DTC_FLAGS += -Wno-unit_address_vs_reg \ + -Wno-unit_address_format \ ++ -Wno-gpios_property \ + -Wno-avoid_unnecessary_addr_size \ + -Wno-alias_paths \ + -Wno-graph_child_address \ +@@ -341,6 +342,18 @@ endef + $(obj)/%.dt.yaml: $(src)/%.dts $(DTC) $(DT_TMP_SCHEMA) FORCE + $(call if_changed_rule,dtc,yaml) + ++quiet_cmd_dtco = DTCO $@ ++cmd_dtco = mkdir -p $(dir ${dtc-tmp}) ; \ ++ $(CPP) $(dtc_cpp_flags) -x assembler-with-cpp -o $(dtc-tmp) $< ; \ ++ $(DTC) -@ -H epapr -O dtb -o $@ -b 0 \ ++ -i $(dir $<) $(DTC_FLAGS) \ ++ -Wno-interrupts_property \ ++ -d $(depfile).dtc.tmp $(dtc-tmp) ; \ ++ cat $(depfile).pre.tmp $(depfile).dtc.tmp > $(depfile) ++ ++$(obj)/%.dtbo: $(src)/%-overlay.dts FORCE ++ $(call if_changed_dep,dtco) ++ + dtc-tmp = $(subst $(comma),_,$(dot-target).dts.tmp) + + # Bzip2 +-- +2.30.2 + diff --git a/target/linux/bcm27xx/patches-5.10/950-0055-BCM270x_DT-Add-pwr_led-and-the-required-input-trigge.patch b/target/linux/bcm27xx/patches-5.10/950-0055-BCM270x_DT-Add-pwr_led-and-the-required-input-trigge.patch new file mode 100644 index 0000000000..36622bb30a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0055-BCM270x_DT-Add-pwr_led-and-the-required-input-trigge.patch @@ -0,0 +1,169 @@ +From 3bb38201fc6c1aef7709c3c744824db23f06c629 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 6 Feb 2015 13:50:57 +0000 +Subject: [PATCH] BCM270x_DT: Add pwr_led, and the required "input" + trigger + +The "input" trigger makes the associated GPIO an input. This is to support +the Raspberry Pi PWR LED, which is driven by external hardware in normal use. + +N.B. pwr_led is not available on Model A or B boards. + +leds-gpio: Implement the brightness_get method + +The power LED uses some clever logic that means it is driven +by a voltage measuring circuit when configured as input, otherwise +it is driven by the GPIO output value. This patch wires up the +brightness_get method for leds-gpio so that user-space can monitor +the LED value via /sys/class/gpio/led1/brightness. Using the input +trigger this returns an indication of the system power health, +otherwise it is just whatever value the trigger has written most +recently. + +See: https://github.com/raspberrypi/linux/issues/1064 +--- + drivers/leds/leds-gpio.c | 17 ++++++++- + drivers/leds/trigger/Kconfig | 7 ++++ + drivers/leds/trigger/Makefile | 1 + + drivers/leds/trigger/ledtrig-input.c | 55 ++++++++++++++++++++++++++++ + include/linux/leds.h | 3 ++ + 5 files changed, 82 insertions(+), 1 deletion(-) + create mode 100644 drivers/leds/trigger/ledtrig-input.c + +--- a/drivers/leds/leds-gpio.c ++++ b/drivers/leds/leds-gpio.c +@@ -46,8 +46,15 @@ static void gpio_led_set(struct led_clas + led_dat->platform_gpio_blink_set(led_dat->gpiod, level, + NULL, NULL); + led_dat->blinking = 0; ++ } else if (led_dat->cdev.flags & SET_GPIO_INPUT) { ++ gpiod_direction_input(led_dat->gpiod); ++ led_dat->cdev.flags &= ~SET_GPIO_INPUT; ++ } else if (led_dat->cdev.flags & SET_GPIO_OUTPUT) { ++ gpiod_direction_output(led_dat->gpiod, level); ++ led_dat->cdev.flags &= ~SET_GPIO_OUTPUT; + } else { +- if (led_dat->can_sleep) ++ if (led_dat->can_sleep || ++ (led_dat->cdev.flags & (SET_GPIO_INPUT | SET_GPIO_OUTPUT) )) + gpiod_set_value_cansleep(led_dat->gpiod, level); + else + gpiod_set_value(led_dat->gpiod, level); +@@ -61,6 +68,13 @@ static int gpio_led_set_blocking(struct + return 0; + } + ++static enum led_brightness gpio_led_get(struct led_classdev *led_cdev) ++{ ++ struct gpio_led_data *led_dat = ++ container_of(led_cdev, struct gpio_led_data, cdev); ++ return gpiod_get_value_cansleep(led_dat->gpiod) ? LED_FULL : LED_OFF; ++} ++ + static int gpio_blink_set(struct led_classdev *led_cdev, + unsigned long *delay_on, unsigned long *delay_off) + { +@@ -89,6 +103,7 @@ static int create_gpio_led(const struct + led_dat->platform_gpio_blink_set = blink_set; + led_dat->cdev.blink_set = gpio_blink_set; + } ++ led_dat->cdev.brightness_get = gpio_led_get; + if (template->default_state == LEDS_GPIO_DEFSTATE_KEEP) { + state = gpiod_get_value_cansleep(led_dat->gpiod); + if (state < 0) +--- a/drivers/leds/trigger/Kconfig ++++ b/drivers/leds/trigger/Kconfig +@@ -114,6 +114,13 @@ config LEDS_TRIGGER_CAMERA + This enables direct flash/torch on/off by the driver, kernel space. + If unsure, say Y. + ++config LEDS_TRIGGER_INPUT ++ tristate "LED Input Trigger" ++ depends on LEDS_TRIGGERS ++ help ++ This allows the GPIOs assigned to be LEDs to be initialised to inputs. ++ If unsure, say Y. ++ + config LEDS_TRIGGER_PANIC + bool "LED Panic Trigger" + help +--- a/drivers/leds/trigger/Makefile ++++ b/drivers/leds/trigger/Makefile +@@ -11,6 +11,7 @@ obj-$(CONFIG_LEDS_TRIGGER_ACTIVITY) += l + obj-$(CONFIG_LEDS_TRIGGER_DEFAULT_ON) += ledtrig-default-on.o + obj-$(CONFIG_LEDS_TRIGGER_TRANSIENT) += ledtrig-transient.o + obj-$(CONFIG_LEDS_TRIGGER_CAMERA) += ledtrig-camera.o ++obj-$(CONFIG_LEDS_TRIGGER_INPUT) += ledtrig-input.o + obj-$(CONFIG_LEDS_TRIGGER_PANIC) += ledtrig-panic.o + obj-$(CONFIG_LEDS_TRIGGER_NETDEV) += ledtrig-netdev.o + obj-$(CONFIG_LEDS_TRIGGER_PATTERN) += ledtrig-pattern.o +--- /dev/null ++++ b/drivers/leds/trigger/ledtrig-input.c +@@ -0,0 +1,55 @@ ++/* ++ * Set LED GPIO to Input "Trigger" ++ * ++ * Copyright 2015 Phil Elwell ++ * ++ * Based on Nick Forbes's ledtrig-default-on.c. ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ * ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include "../leds.h" ++ ++static int input_trig_activate(struct led_classdev *led_cdev) ++{ ++ led_cdev->flags |= SET_GPIO_INPUT; ++ led_set_brightness(led_cdev, 0); ++ return 0; ++} ++ ++static void input_trig_deactivate(struct led_classdev *led_cdev) ++{ ++ led_cdev->flags |= SET_GPIO_OUTPUT; ++ led_set_brightness(led_cdev, 0); ++} ++ ++static struct led_trigger input_led_trigger = { ++ .name = "input", ++ .activate = input_trig_activate, ++ .deactivate = input_trig_deactivate, ++}; ++ ++static int __init input_trig_init(void) ++{ ++ return led_trigger_register(&input_led_trigger); ++} ++ ++static void __exit input_trig_exit(void) ++{ ++ led_trigger_unregister(&input_led_trigger); ++} ++ ++module_init(input_trig_init); ++module_exit(input_trig_exit); ++ ++MODULE_AUTHOR("Phil Elwell "); ++MODULE_DESCRIPTION("Set LED GPIO to Input \"trigger\""); ++MODULE_LICENSE("GPL"); +--- a/include/linux/leds.h ++++ b/include/linux/leds.h +@@ -79,6 +79,9 @@ struct led_classdev { + #define LED_BRIGHT_HW_CHANGED BIT(21) + #define LED_RETAIN_AT_SHUTDOWN BIT(22) + #define LED_INIT_DEFAULT_TRIGGER BIT(23) ++ /* Additions for Raspberry Pi PWR LED */ ++#define SET_GPIO_INPUT BIT(30) ++#define SET_GPIO_OUTPUT BIT(31) + + /* set_brightness_work / blink_timer flags, atomic, private. */ + unsigned long work_flags; diff --git a/target/linux/bcm27xx/patches-5.10/950-0056-Added-Device-IDs-for-August-DVB-T-205.patch b/target/linux/bcm27xx/patches-5.10/950-0056-Added-Device-IDs-for-August-DVB-T-205.patch new file mode 100644 index 0000000000..ba2cf0d77a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0056-Added-Device-IDs-for-August-DVB-T-205.patch @@ -0,0 +1,22 @@ +From 6bfe5935985ffc3b5365877db6e8b90ba4924540 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Wed, 3 Jul 2013 00:54:08 +0100 +Subject: [PATCH] Added Device IDs for August DVB-T 205 + +--- + drivers/media/usb/dvb-usb-v2/rtl28xxu.c | 4 ++++ + 1 file changed, 4 insertions(+) + +--- a/drivers/media/usb/dvb-usb-v2/rtl28xxu.c ++++ b/drivers/media/usb/dvb-usb-v2/rtl28xxu.c +@@ -1953,6 +1953,10 @@ static const struct usb_device_id rtl28x + &rtl28xxu_props, "Compro VideoMate U650F", NULL) }, + { DVB_USB_DEVICE(USB_VID_KWORLD_2, 0xd394, + &rtl28xxu_props, "MaxMedia HU394-T", NULL) }, ++ { DVB_USB_DEVICE(USB_VID_GTEK, 0xb803 /*USB_PID_AUGUST_DVBT205*/, ++ &rtl28xxu_props, "August DVB-T 205", NULL) }, ++ { DVB_USB_DEVICE(USB_VID_GTEK, 0xa803 /*USB_PID_AUGUST_DVBT205*/, ++ &rtl28xxu_props, "August DVB-T 205", NULL) }, + { DVB_USB_DEVICE(USB_VID_LEADTEK, 0x6a03, + &rtl28xxu_props, "Leadtek WinFast DTV Dongle mini", NULL) }, + { DVB_USB_DEVICE(USB_VID_GTEK, USB_PID_CPYTO_REDI_PC50A, diff --git a/target/linux/bcm27xx/patches-5.10/950-0057-Improve-__copy_to_user-and-__copy_from_user-performa.patch b/target/linux/bcm27xx/patches-5.10/950-0057-Improve-__copy_to_user-and-__copy_from_user-performa.patch new file mode 100644 index 0000000000..7fff55b50c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0057-Improve-__copy_to_user-and-__copy_from_user-performa.patch @@ -0,0 +1,1586 @@ +From a013e78cd135c415124496edd439b1031102c33c Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Mon, 28 Nov 2016 16:50:04 +0000 +Subject: [PATCH] Improve __copy_to_user and __copy_from_user + performance + +Provide a __copy_from_user that uses memcpy. On BCM2708, use +optimised memcpy/memmove/memcmp/memset implementations. + +arch/arm: Add mmiocpy/set aliases for memcpy/set + +See: https://github.com/raspberrypi/linux/issues/1082 + +copy_from_user: CPU_SW_DOMAIN_PAN compatibility + +The downstream copy_from_user acceleration must also play nice with +CONFIG_CPU_SW_DOMAIN_PAN. + +See: https://github.com/raspberrypi/linux/issues/1381 + +Signed-off-by: Phil Elwell + +Fix copy_from_user if BCM2835_FAST_MEMCPY=n + +The change which introduced CONFIG_BCM2835_FAST_MEMCPY unconditionally +changed the behaviour of arm_copy_from_user. The page pinning code +is not safe on ARMv7 if LPAE & high memory is enabled and causes +crashes which look like PTE corruption. + +Make __copy_from_user_memcpy conditional on CONFIG_2835_FAST_MEMCPY=y +which is really an ARMv6 / Pi1 optimization and not necessary on newer +ARM processors. + +arm: fix mmap unlocks in uaccess_with_memcpy.c + +This is a regression that was added with the commit 192a4e923ef092924dd013e7326f2ec520ee4783 as of rpi-5.8.y, since that is when the move to the mmap locking API was introduced - d8ed45c5dcd455fc5848d47f86883a1b872ac0d0 + +The issue is that when the patch to improve performance for the __copy_to_user and __copy_from_user functions were added for the Raspberry Pi, some of the mmaps were incorrectly mapped to write instead of read. This would cause a verity of issues, and in my case, prevent the booting of a squashfs filesystem on rpi-5.8-y and above. An example of the panic you would see from this can be seen at https://pastebin.com/raw/jBz5xCzL + +Signed-off-by: Christian Lamparter +Signed-off-by: Christopher Blake +--- + arch/arm/include/asm/string.h | 5 + + arch/arm/include/asm/uaccess.h | 3 + + arch/arm/lib/Makefile | 14 +- + arch/arm/lib/arm-mem.h | 159 +++++++++ + arch/arm/lib/copy_from_user.S | 4 +- + arch/arm/lib/exports_rpi.c | 37 +++ + arch/arm/lib/memcmp_rpi.S | 285 ++++++++++++++++ + arch/arm/lib/memcpy_rpi.S | 61 ++++ + arch/arm/lib/memcpymove.h | 506 +++++++++++++++++++++++++++++ + arch/arm/lib/memmove_rpi.S | 61 ++++ + arch/arm/lib/memset_rpi.S | 128 ++++++++ + arch/arm/lib/uaccess_with_memcpy.c | 130 +++++++- + arch/arm/mach-bcm/Kconfig | 7 + + 13 files changed, 1394 insertions(+), 6 deletions(-) + create mode 100644 arch/arm/lib/arm-mem.h + create mode 100644 arch/arm/lib/exports_rpi.c + create mode 100644 arch/arm/lib/memcmp_rpi.S + create mode 100644 arch/arm/lib/memcpy_rpi.S + create mode 100644 arch/arm/lib/memcpymove.h + create mode 100644 arch/arm/lib/memmove_rpi.S + create mode 100644 arch/arm/lib/memset_rpi.S + +--- a/arch/arm/include/asm/string.h ++++ b/arch/arm/include/asm/string.h +@@ -39,4 +39,9 @@ static inline void *memset64(uint64_t *p + return __memset64(p, v, n * 8, v >> 32); + } + ++#ifdef CONFIG_BCM2835_FAST_MEMCPY ++#define __HAVE_ARCH_MEMCMP ++extern int memcmp(const void *, const void *, size_t); ++#endif ++ + #endif +--- a/arch/arm/include/asm/uaccess.h ++++ b/arch/arm/include/asm/uaccess.h +@@ -516,6 +516,9 @@ do { \ + extern unsigned long __must_check + arm_copy_from_user(void *to, const void __user *from, unsigned long n); + ++extern unsigned long __must_check ++__copy_from_user_std(void *to, const void __user *from, unsigned long n); ++ + static inline unsigned long __must_check + raw_copy_from_user(void *to, const void __user *from, unsigned long n) + { +--- a/arch/arm/lib/Makefile ++++ b/arch/arm/lib/Makefile +@@ -7,8 +7,8 @@ + + lib-y := changebit.o csumipv6.o csumpartial.o \ + csumpartialcopy.o csumpartialcopyuser.o clearbit.o \ +- delay.o delay-loop.o findbit.o memchr.o memcpy.o \ +- memmove.o memset.o setbit.o \ ++ delay.o delay-loop.o findbit.o memchr.o \ ++ setbit.o \ + strchr.o strrchr.o \ + testchangebit.o testclearbit.o testsetbit.o \ + ashldi3.o ashrdi3.o lshrdi3.o muldi3.o \ +@@ -25,6 +25,16 @@ else + lib-y += backtrace.o + endif + ++# Choose optimised implementations for Raspberry Pi ++ifeq ($(CONFIG_BCM2835_FAST_MEMCPY),y) ++ CFLAGS_uaccess_with_memcpy.o += -DCOPY_FROM_USER_THRESHOLD=1600 ++ CFLAGS_uaccess_with_memcpy.o += -DCOPY_TO_USER_THRESHOLD=672 ++ obj-$(CONFIG_MODULES) += exports_rpi.o ++ lib-y += memcpy_rpi.o memmove_rpi.o memset_rpi.o memcmp_rpi.o ++else ++ lib-y += memcpy.o memmove.o memset.o ++endif ++ + # using lib_ here won't override already available weak symbols + obj-$(CONFIG_UACCESS_WITH_MEMCPY) += uaccess_with_memcpy.o + +--- /dev/null ++++ b/arch/arm/lib/arm-mem.h +@@ -0,0 +1,159 @@ ++/* ++Copyright (c) 2013, Raspberry Pi Foundation ++Copyright (c) 2013, RISC OS Open Ltd ++All rights reserved. ++ ++Redistribution and use in source and binary forms, with or without ++modification, are permitted provided that the following conditions are met: ++ * Redistributions of source code must retain the above copyright ++ notice, this list of conditions and the following disclaimer. ++ * Redistributions in binary form must reproduce the above copyright ++ notice, this list of conditions and the following disclaimer in the ++ documentation and/or other materials provided with the distribution. ++ * Neither the name of the copyright holder nor the ++ names of its contributors may be used to endorse or promote products ++ derived from this software without specific prior written permission. ++ ++THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ++ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED ++WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE ++DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY ++DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; ++LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ++ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++*/ ++ ++.macro myfunc fname ++ .func fname ++ .global fname ++fname: ++.endm ++ ++.macro preload_leading_step1 backwards, ptr, base ++/* If the destination is already 16-byte aligned, then we need to preload ++ * between 0 and prefetch_distance (inclusive) cache lines ahead so there ++ * are no gaps when the inner loop starts. ++ */ ++ .if backwards ++ sub ptr, base, #1 ++ bic ptr, ptr, #31 ++ .else ++ bic ptr, base, #31 ++ .endif ++ .set OFFSET, 0 ++ .rept prefetch_distance+1 ++ pld [ptr, #OFFSET] ++ .if backwards ++ .set OFFSET, OFFSET-32 ++ .else ++ .set OFFSET, OFFSET+32 ++ .endif ++ .endr ++.endm ++ ++.macro preload_leading_step2 backwards, ptr, base, leading_bytes, tmp ++/* However, if the destination is not 16-byte aligned, we may need to ++ * preload one more cache line than that. The question we need to ask is: ++ * are the leading bytes more than the amount by which the source ++ * pointer will be rounded down for preloading, and if so, by how many ++ * cache lines? ++ */ ++ .if backwards ++/* Here we compare against how many bytes we are into the ++ * cache line, counting down from the highest such address. ++ * Effectively, we want to calculate ++ * leading_bytes = dst&15 ++ * cacheline_offset = 31-((src-leading_bytes-1)&31) ++ * extra_needed = leading_bytes - cacheline_offset ++ * and test if extra_needed is <= 0, or rearranging: ++ * leading_bytes + (src-leading_bytes-1)&31 <= 31 ++ */ ++ mov tmp, base, lsl #32-5 ++ sbc tmp, tmp, leading_bytes, lsl #32-5 ++ adds tmp, tmp, leading_bytes, lsl #32-5 ++ bcc 61f ++ pld [ptr, #-32*(prefetch_distance+1)] ++ .else ++/* Effectively, we want to calculate ++ * leading_bytes = (-dst)&15 ++ * cacheline_offset = (src+leading_bytes)&31 ++ * extra_needed = leading_bytes - cacheline_offset ++ * and test if extra_needed is <= 0. ++ */ ++ mov tmp, base, lsl #32-5 ++ add tmp, tmp, leading_bytes, lsl #32-5 ++ rsbs tmp, tmp, leading_bytes, lsl #32-5 ++ bls 61f ++ pld [ptr, #32*(prefetch_distance+1)] ++ .endif ++61: ++.endm ++ ++.macro preload_trailing backwards, base, remain, tmp ++ /* We need either 0, 1 or 2 extra preloads */ ++ .if backwards ++ rsb tmp, base, #0 ++ mov tmp, tmp, lsl #32-5 ++ .else ++ mov tmp, base, lsl #32-5 ++ .endif ++ adds tmp, tmp, remain, lsl #32-5 ++ adceqs tmp, tmp, #0 ++ /* The instruction above has two effects: ensures Z is only ++ * set if C was clear (so Z indicates that both shifted quantities ++ * were 0), and clears C if Z was set (so C indicates that the sum ++ * of the shifted quantities was greater and not equal to 32) */ ++ beq 82f ++ .if backwards ++ sub tmp, base, #1 ++ bic tmp, tmp, #31 ++ .else ++ bic tmp, base, #31 ++ .endif ++ bcc 81f ++ .if backwards ++ pld [tmp, #-32*(prefetch_distance+1)] ++81: ++ pld [tmp, #-32*prefetch_distance] ++ .else ++ pld [tmp, #32*(prefetch_distance+2)] ++81: ++ pld [tmp, #32*(prefetch_distance+1)] ++ .endif ++82: ++.endm ++ ++.macro preload_all backwards, narrow_case, shift, base, remain, tmp0, tmp1 ++ .if backwards ++ sub tmp0, base, #1 ++ bic tmp0, tmp0, #31 ++ pld [tmp0] ++ sub tmp1, base, remain, lsl #shift ++ .else ++ bic tmp0, base, #31 ++ pld [tmp0] ++ add tmp1, base, remain, lsl #shift ++ sub tmp1, tmp1, #1 ++ .endif ++ bic tmp1, tmp1, #31 ++ cmp tmp1, tmp0 ++ beq 92f ++ .if narrow_case ++ /* In this case, all the data fits in either 1 or 2 cache lines */ ++ pld [tmp1] ++ .else ++91: ++ .if backwards ++ sub tmp0, tmp0, #32 ++ .else ++ add tmp0, tmp0, #32 ++ .endif ++ cmp tmp0, tmp1 ++ pld [tmp0] ++ bne 91b ++ .endif ++92: ++.endm +--- a/arch/arm/lib/copy_from_user.S ++++ b/arch/arm/lib/copy_from_user.S +@@ -107,7 +107,8 @@ + + .text + +-ENTRY(arm_copy_from_user) ++ENTRY(__copy_from_user_std) ++WEAK(arm_copy_from_user) + #ifdef CONFIG_CPU_SPECTRE + get_thread_info r3 + ldr r3, [r3, #TI_ADDR_LIMIT] +@@ -117,6 +118,7 @@ ENTRY(arm_copy_from_user) + #include "copy_template.S" + + ENDPROC(arm_copy_from_user) ++ENDPROC(__copy_from_user_std) + + .pushsection .text.fixup,"ax" + .align 0 +--- /dev/null ++++ b/arch/arm/lib/exports_rpi.c +@@ -0,0 +1,37 @@ ++/** ++ * Copyright (c) 2014, Raspberry Pi (Trading) Ltd. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions ++ * are met: ++ * 1. Redistributions of source code must retain the above copyright ++ * notice, this list of conditions, and the following disclaimer, ++ * without modification. ++ * 2. Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in the ++ * documentation and/or other materials provided with the distribution. ++ * 3. The names of the above-listed copyright holders may not be used ++ * to endorse or promote products derived from this software without ++ * specific prior written permission. ++ * ++ * ALTERNATIVELY, this software may be distributed under the terms of the ++ * GNU General Public License ("GPL") version 2, as published by the Free ++ * Software Foundation. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS ++ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ++ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR ++ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR ++ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF ++ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING ++ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ */ ++ ++#include ++#include ++ ++EXPORT_SYMBOL(memcmp); +--- /dev/null ++++ b/arch/arm/lib/memcmp_rpi.S +@@ -0,0 +1,285 @@ ++/* ++Copyright (c) 2013, Raspberry Pi Foundation ++Copyright (c) 2013, RISC OS Open Ltd ++All rights reserved. ++ ++Redistribution and use in source and binary forms, with or without ++modification, are permitted provided that the following conditions are met: ++ * Redistributions of source code must retain the above copyright ++ notice, this list of conditions and the following disclaimer. ++ * Redistributions in binary form must reproduce the above copyright ++ notice, this list of conditions and the following disclaimer in the ++ documentation and/or other materials provided with the distribution. ++ * Neither the name of the copyright holder nor the ++ names of its contributors may be used to endorse or promote products ++ derived from this software without specific prior written permission. ++ ++THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ++ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED ++WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE ++DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY ++DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; ++LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ++ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++*/ ++ ++#include ++#include "arm-mem.h" ++ ++/* Prevent the stack from becoming executable */ ++#if defined(__linux__) && defined(__ELF__) ++.section .note.GNU-stack,"",%progbits ++#endif ++ ++ .text ++ .arch armv6 ++ .object_arch armv4 ++ .arm ++ .altmacro ++ .p2align 2 ++ ++.macro memcmp_process_head unaligned ++ .if unaligned ++ ldr DAT0, [S_1], #4 ++ ldr DAT1, [S_1], #4 ++ ldr DAT2, [S_1], #4 ++ ldr DAT3, [S_1], #4 ++ .else ++ ldmia S_1!, {DAT0, DAT1, DAT2, DAT3} ++ .endif ++ ldmia S_2!, {DAT4, DAT5, DAT6, DAT7} ++.endm ++ ++.macro memcmp_process_tail ++ cmp DAT0, DAT4 ++ cmpeq DAT1, DAT5 ++ cmpeq DAT2, DAT6 ++ cmpeq DAT3, DAT7 ++ bne 200f ++.endm ++ ++.macro memcmp_leading_31bytes ++ movs DAT0, OFF, lsl #31 ++ ldrmib DAT0, [S_1], #1 ++ ldrcsh DAT1, [S_1], #2 ++ ldrmib DAT4, [S_2], #1 ++ ldrcsh DAT5, [S_2], #2 ++ movpl DAT0, #0 ++ movcc DAT1, #0 ++ movpl DAT4, #0 ++ movcc DAT5, #0 ++ submi N, N, #1 ++ subcs N, N, #2 ++ cmp DAT0, DAT4 ++ cmpeq DAT1, DAT5 ++ bne 200f ++ movs DAT0, OFF, lsl #29 ++ ldrmi DAT0, [S_1], #4 ++ ldrcs DAT1, [S_1], #4 ++ ldrcs DAT2, [S_1], #4 ++ ldrmi DAT4, [S_2], #4 ++ ldmcsia S_2!, {DAT5, DAT6} ++ movpl DAT0, #0 ++ movcc DAT1, #0 ++ movcc DAT2, #0 ++ movpl DAT4, #0 ++ movcc DAT5, #0 ++ movcc DAT6, #0 ++ submi N, N, #4 ++ subcs N, N, #8 ++ cmp DAT0, DAT4 ++ cmpeq DAT1, DAT5 ++ cmpeq DAT2, DAT6 ++ bne 200f ++ tst OFF, #16 ++ beq 105f ++ memcmp_process_head 1 ++ sub N, N, #16 ++ memcmp_process_tail ++105: ++.endm ++ ++.macro memcmp_trailing_15bytes unaligned ++ movs N, N, lsl #29 ++ .if unaligned ++ ldrcs DAT0, [S_1], #4 ++ ldrcs DAT1, [S_1], #4 ++ .else ++ ldmcsia S_1!, {DAT0, DAT1} ++ .endif ++ ldrmi DAT2, [S_1], #4 ++ ldmcsia S_2!, {DAT4, DAT5} ++ ldrmi DAT6, [S_2], #4 ++ movcc DAT0, #0 ++ movcc DAT1, #0 ++ movpl DAT2, #0 ++ movcc DAT4, #0 ++ movcc DAT5, #0 ++ movpl DAT6, #0 ++ cmp DAT0, DAT4 ++ cmpeq DAT1, DAT5 ++ cmpeq DAT2, DAT6 ++ bne 200f ++ movs N, N, lsl #2 ++ ldrcsh DAT0, [S_1], #2 ++ ldrmib DAT1, [S_1] ++ ldrcsh DAT4, [S_2], #2 ++ ldrmib DAT5, [S_2] ++ movcc DAT0, #0 ++ movpl DAT1, #0 ++ movcc DAT4, #0 ++ movpl DAT5, #0 ++ cmp DAT0, DAT4 ++ cmpeq DAT1, DAT5 ++ bne 200f ++.endm ++ ++.macro memcmp_long_inner_loop unaligned ++110: ++ memcmp_process_head unaligned ++ pld [S_2, #prefetch_distance*32 + 16] ++ memcmp_process_tail ++ memcmp_process_head unaligned ++ pld [S_1, OFF] ++ memcmp_process_tail ++ subs N, N, #32 ++ bhs 110b ++ /* Just before the final (prefetch_distance+1) 32-byte blocks, ++ * deal with final preloads */ ++ preload_trailing 0, S_1, N, DAT0 ++ preload_trailing 0, S_2, N, DAT0 ++ add N, N, #(prefetch_distance+2)*32 - 16 ++120: ++ memcmp_process_head unaligned ++ memcmp_process_tail ++ subs N, N, #16 ++ bhs 120b ++ /* Trailing words and bytes */ ++ tst N, #15 ++ beq 199f ++ memcmp_trailing_15bytes unaligned ++199: /* Reached end without detecting a difference */ ++ mov a1, #0 ++ setend le ++ pop {DAT1-DAT6, pc} ++.endm ++ ++.macro memcmp_short_inner_loop unaligned ++ subs N, N, #16 /* simplifies inner loop termination */ ++ blo 122f ++120: ++ memcmp_process_head unaligned ++ memcmp_process_tail ++ subs N, N, #16 ++ bhs 120b ++122: /* Trailing words and bytes */ ++ tst N, #15 ++ beq 199f ++ memcmp_trailing_15bytes unaligned ++199: /* Reached end without detecting a difference */ ++ mov a1, #0 ++ setend le ++ pop {DAT1-DAT6, pc} ++.endm ++ ++/* ++ * int memcmp(const void *s1, const void *s2, size_t n); ++ * On entry: ++ * a1 = pointer to buffer 1 ++ * a2 = pointer to buffer 2 ++ * a3 = number of bytes to compare (as unsigned chars) ++ * On exit: ++ * a1 = >0/=0/<0 if s1 >/=/< s2 ++ */ ++ ++.set prefetch_distance, 2 ++ ++ENTRY(memcmp) ++ S_1 .req a1 ++ S_2 .req a2 ++ N .req a3 ++ DAT0 .req a4 ++ DAT1 .req v1 ++ DAT2 .req v2 ++ DAT3 .req v3 ++ DAT4 .req v4 ++ DAT5 .req v5 ++ DAT6 .req v6 ++ DAT7 .req ip ++ OFF .req lr ++ ++ push {DAT1-DAT6, lr} ++ setend be /* lowest-addressed bytes are most significant */ ++ ++ /* To preload ahead as we go, we need at least (prefetch_distance+2) 32-byte blocks */ ++ cmp N, #(prefetch_distance+3)*32 - 1 ++ blo 170f ++ ++ /* Long case */ ++ /* Adjust N so that the decrement instruction can also test for ++ * inner loop termination. We want it to stop when there are ++ * (prefetch_distance+1) complete blocks to go. */ ++ sub N, N, #(prefetch_distance+2)*32 ++ preload_leading_step1 0, DAT0, S_1 ++ preload_leading_step1 0, DAT1, S_2 ++ tst S_2, #31 ++ beq 154f ++ rsb OFF, S_2, #0 /* no need to AND with 15 here */ ++ preload_leading_step2 0, DAT0, S_1, OFF, DAT2 ++ preload_leading_step2 0, DAT1, S_2, OFF, DAT2 ++ memcmp_leading_31bytes ++154: /* Second source now cacheline (32-byte) aligned; we have at ++ * least one prefetch to go. */ ++ /* Prefetch offset is best selected such that it lies in the ++ * first 8 of each 32 bytes - but it's just as easy to aim for ++ * the first one */ ++ and OFF, S_1, #31 ++ rsb OFF, OFF, #32*prefetch_distance ++ tst S_1, #3 ++ bne 140f ++ memcmp_long_inner_loop 0 ++140: memcmp_long_inner_loop 1 ++ ++170: /* Short case */ ++ teq N, #0 ++ beq 199f ++ preload_all 0, 0, 0, S_1, N, DAT0, DAT1 ++ preload_all 0, 0, 0, S_2, N, DAT0, DAT1 ++ tst S_2, #3 ++ beq 174f ++172: subs N, N, #1 ++ blo 199f ++ ldrb DAT0, [S_1], #1 ++ ldrb DAT4, [S_2], #1 ++ cmp DAT0, DAT4 ++ bne 200f ++ tst S_2, #3 ++ bne 172b ++174: /* Second source now 4-byte aligned; we have 0 or more bytes to go */ ++ tst S_1, #3 ++ bne 140f ++ memcmp_short_inner_loop 0 ++140: memcmp_short_inner_loop 1 ++ ++200: /* Difference found: determine sign. */ ++ movhi a1, #1 ++ movlo a1, #-1 ++ setend le ++ pop {DAT1-DAT6, pc} ++ ++ .unreq S_1 ++ .unreq S_2 ++ .unreq N ++ .unreq DAT0 ++ .unreq DAT1 ++ .unreq DAT2 ++ .unreq DAT3 ++ .unreq DAT4 ++ .unreq DAT5 ++ .unreq DAT6 ++ .unreq DAT7 ++ .unreq OFF ++ENDPROC(memcmp) +--- /dev/null ++++ b/arch/arm/lib/memcpy_rpi.S +@@ -0,0 +1,61 @@ ++/* ++Copyright (c) 2013, Raspberry Pi Foundation ++Copyright (c) 2013, RISC OS Open Ltd ++All rights reserved. ++ ++Redistribution and use in source and binary forms, with or without ++modification, are permitted provided that the following conditions are met: ++ * Redistributions of source code must retain the above copyright ++ notice, this list of conditions and the following disclaimer. ++ * Redistributions in binary form must reproduce the above copyright ++ notice, this list of conditions and the following disclaimer in the ++ documentation and/or other materials provided with the distribution. ++ * Neither the name of the copyright holder nor the ++ names of its contributors may be used to endorse or promote products ++ derived from this software without specific prior written permission. ++ ++THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ++ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED ++WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE ++DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY ++DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; ++LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ++ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++*/ ++ ++#include ++#include "arm-mem.h" ++#include "memcpymove.h" ++ ++/* Prevent the stack from becoming executable */ ++#if defined(__linux__) && defined(__ELF__) ++.section .note.GNU-stack,"",%progbits ++#endif ++ ++ .text ++ .arch armv6 ++ .object_arch armv4 ++ .arm ++ .altmacro ++ .p2align 2 ++ ++/* ++ * void *memcpy(void * restrict s1, const void * restrict s2, size_t n); ++ * On entry: ++ * a1 = pointer to destination ++ * a2 = pointer to source ++ * a3 = number of bytes to copy ++ * On exit: ++ * a1 preserved ++ */ ++ ++.set prefetch_distance, 3 ++ ++ENTRY(mmiocpy) ++ENTRY(memcpy) ++ memcpy 0 ++ENDPROC(memcpy) ++ENDPROC(mmiocpy) +--- /dev/null ++++ b/arch/arm/lib/memcpymove.h +@@ -0,0 +1,506 @@ ++/* ++Copyright (c) 2013, Raspberry Pi Foundation ++Copyright (c) 2013, RISC OS Open Ltd ++All rights reserved. ++ ++Redistribution and use in source and binary forms, with or without ++modification, are permitted provided that the following conditions are met: ++ * Redistributions of source code must retain the above copyright ++ notice, this list of conditions and the following disclaimer. ++ * Redistributions in binary form must reproduce the above copyright ++ notice, this list of conditions and the following disclaimer in the ++ documentation and/or other materials provided with the distribution. ++ * Neither the name of the copyright holder nor the ++ names of its contributors may be used to endorse or promote products ++ derived from this software without specific prior written permission. ++ ++THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ++ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED ++WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE ++DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY ++DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; ++LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ++ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++*/ ++ ++.macro unaligned_words backwards, align, use_pld, words, r0, r1, r2, r3, r4, r5, r6, r7, r8 ++ .if words == 1 ++ .if backwards ++ mov r1, r0, lsl #32-align*8 ++ ldr r0, [S, #-4]! ++ orr r1, r1, r0, lsr #align*8 ++ str r1, [D, #-4]! ++ .else ++ mov r0, r1, lsr #align*8 ++ ldr r1, [S, #4]! ++ orr r0, r0, r1, lsl #32-align*8 ++ str r0, [D], #4 ++ .endif ++ .elseif words == 2 ++ .if backwards ++ ldr r1, [S, #-4]! ++ mov r2, r0, lsl #32-align*8 ++ ldr r0, [S, #-4]! ++ orr r2, r2, r1, lsr #align*8 ++ mov r1, r1, lsl #32-align*8 ++ orr r1, r1, r0, lsr #align*8 ++ stmdb D!, {r1, r2} ++ .else ++ ldr r1, [S, #4]! ++ mov r0, r2, lsr #align*8 ++ ldr r2, [S, #4]! ++ orr r0, r0, r1, lsl #32-align*8 ++ mov r1, r1, lsr #align*8 ++ orr r1, r1, r2, lsl #32-align*8 ++ stmia D!, {r0, r1} ++ .endif ++ .elseif words == 4 ++ .if backwards ++ ldmdb S!, {r2, r3} ++ mov r4, r0, lsl #32-align*8 ++ ldmdb S!, {r0, r1} ++ orr r4, r4, r3, lsr #align*8 ++ mov r3, r3, lsl #32-align*8 ++ orr r3, r3, r2, lsr #align*8 ++ mov r2, r2, lsl #32-align*8 ++ orr r2, r2, r1, lsr #align*8 ++ mov r1, r1, lsl #32-align*8 ++ orr r1, r1, r0, lsr #align*8 ++ stmdb D!, {r1, r2, r3, r4} ++ .else ++ ldmib S!, {r1, r2} ++ mov r0, r4, lsr #align*8 ++ ldmib S!, {r3, r4} ++ orr r0, r0, r1, lsl #32-align*8 ++ mov r1, r1, lsr #align*8 ++ orr r1, r1, r2, lsl #32-align*8 ++ mov r2, r2, lsr #align*8 ++ orr r2, r2, r3, lsl #32-align*8 ++ mov r3, r3, lsr #align*8 ++ orr r3, r3, r4, lsl #32-align*8 ++ stmia D!, {r0, r1, r2, r3} ++ .endif ++ .elseif words == 8 ++ .if backwards ++ ldmdb S!, {r4, r5, r6, r7} ++ mov r8, r0, lsl #32-align*8 ++ ldmdb S!, {r0, r1, r2, r3} ++ .if use_pld ++ pld [S, OFF] ++ .endif ++ orr r8, r8, r7, lsr #align*8 ++ mov r7, r7, lsl #32-align*8 ++ orr r7, r7, r6, lsr #align*8 ++ mov r6, r6, lsl #32-align*8 ++ orr r6, r6, r5, lsr #align*8 ++ mov r5, r5, lsl #32-align*8 ++ orr r5, r5, r4, lsr #align*8 ++ mov r4, r4, lsl #32-align*8 ++ orr r4, r4, r3, lsr #align*8 ++ mov r3, r3, lsl #32-align*8 ++ orr r3, r3, r2, lsr #align*8 ++ mov r2, r2, lsl #32-align*8 ++ orr r2, r2, r1, lsr #align*8 ++ mov r1, r1, lsl #32-align*8 ++ orr r1, r1, r0, lsr #align*8 ++ stmdb D!, {r5, r6, r7, r8} ++ stmdb D!, {r1, r2, r3, r4} ++ .else ++ ldmib S!, {r1, r2, r3, r4} ++ mov r0, r8, lsr #align*8 ++ ldmib S!, {r5, r6, r7, r8} ++ .if use_pld ++ pld [S, OFF] ++ .endif ++ orr r0, r0, r1, lsl #32-align*8 ++ mov r1, r1, lsr #align*8 ++ orr r1, r1, r2, lsl #32-align*8 ++ mov r2, r2, lsr #align*8 ++ orr r2, r2, r3, lsl #32-align*8 ++ mov r3, r3, lsr #align*8 ++ orr r3, r3, r4, lsl #32-align*8 ++ mov r4, r4, lsr #align*8 ++ orr r4, r4, r5, lsl #32-align*8 ++ mov r5, r5, lsr #align*8 ++ orr r5, r5, r6, lsl #32-align*8 ++ mov r6, r6, lsr #align*8 ++ orr r6, r6, r7, lsl #32-align*8 ++ mov r7, r7, lsr #align*8 ++ orr r7, r7, r8, lsl #32-align*8 ++ stmia D!, {r0, r1, r2, r3} ++ stmia D!, {r4, r5, r6, r7} ++ .endif ++ .endif ++.endm ++ ++.macro memcpy_leading_15bytes backwards, align ++ movs DAT1, DAT2, lsl #31 ++ sub N, N, DAT2 ++ .if backwards ++ ldrmib DAT0, [S, #-1]! ++ ldrcsh DAT1, [S, #-2]! ++ strmib DAT0, [D, #-1]! ++ strcsh DAT1, [D, #-2]! ++ .else ++ ldrmib DAT0, [S], #1 ++ ldrcsh DAT1, [S], #2 ++ strmib DAT0, [D], #1 ++ strcsh DAT1, [D], #2 ++ .endif ++ movs DAT1, DAT2, lsl #29 ++ .if backwards ++ ldrmi DAT0, [S, #-4]! ++ .if align == 0 ++ ldmcsdb S!, {DAT1, DAT2} ++ .else ++ ldrcs DAT2, [S, #-4]! ++ ldrcs DAT1, [S, #-4]! ++ .endif ++ strmi DAT0, [D, #-4]! ++ stmcsdb D!, {DAT1, DAT2} ++ .else ++ ldrmi DAT0, [S], #4 ++ .if align == 0 ++ ldmcsia S!, {DAT1, DAT2} ++ .else ++ ldrcs DAT1, [S], #4 ++ ldrcs DAT2, [S], #4 ++ .endif ++ strmi DAT0, [D], #4 ++ stmcsia D!, {DAT1, DAT2} ++ .endif ++.endm ++ ++.macro memcpy_trailing_15bytes backwards, align ++ movs N, N, lsl #29 ++ .if backwards ++ .if align == 0 ++ ldmcsdb S!, {DAT0, DAT1} ++ .else ++ ldrcs DAT1, [S, #-4]! ++ ldrcs DAT0, [S, #-4]! ++ .endif ++ ldrmi DAT2, [S, #-4]! ++ stmcsdb D!, {DAT0, DAT1} ++ strmi DAT2, [D, #-4]! ++ .else ++ .if align == 0 ++ ldmcsia S!, {DAT0, DAT1} ++ .else ++ ldrcs DAT0, [S], #4 ++ ldrcs DAT1, [S], #4 ++ .endif ++ ldrmi DAT2, [S], #4 ++ stmcsia D!, {DAT0, DAT1} ++ strmi DAT2, [D], #4 ++ .endif ++ movs N, N, lsl #2 ++ .if backwards ++ ldrcsh DAT0, [S, #-2]! ++ ldrmib DAT1, [S, #-1] ++ strcsh DAT0, [D, #-2]! ++ strmib DAT1, [D, #-1] ++ .else ++ ldrcsh DAT0, [S], #2 ++ ldrmib DAT1, [S] ++ strcsh DAT0, [D], #2 ++ strmib DAT1, [D] ++ .endif ++.endm ++ ++.macro memcpy_long_inner_loop backwards, align ++ .if align != 0 ++ .if backwards ++ ldr DAT0, [S, #-align]! ++ .else ++ ldr LAST, [S, #-align]! ++ .endif ++ .endif ++110: ++ .if align == 0 ++ .if backwards ++ ldmdb S!, {DAT0, DAT1, DAT2, DAT3, DAT4, DAT5, DAT6, LAST} ++ pld [S, OFF] ++ stmdb D!, {DAT4, DAT5, DAT6, LAST} ++ stmdb D!, {DAT0, DAT1, DAT2, DAT3} ++ .else ++ ldmia S!, {DAT0, DAT1, DAT2, DAT3, DAT4, DAT5, DAT6, LAST} ++ pld [S, OFF] ++ stmia D!, {DAT0, DAT1, DAT2, DAT3} ++ stmia D!, {DAT4, DAT5, DAT6, LAST} ++ .endif ++ .else ++ unaligned_words backwards, align, 1, 8, DAT0, DAT1, DAT2, DAT3, DAT4, DAT5, DAT6, DAT7, LAST ++ .endif ++ subs N, N, #32 ++ bhs 110b ++ /* Just before the final (prefetch_distance+1) 32-byte blocks, deal with final preloads */ ++ preload_trailing backwards, S, N, OFF ++ add N, N, #(prefetch_distance+2)*32 - 32 ++120: ++ .if align == 0 ++ .if backwards ++ ldmdb S!, {DAT0, DAT1, DAT2, DAT3, DAT4, DAT5, DAT6, LAST} ++ stmdb D!, {DAT4, DAT5, DAT6, LAST} ++ stmdb D!, {DAT0, DAT1, DAT2, DAT3} ++ .else ++ ldmia S!, {DAT0, DAT1, DAT2, DAT3, DAT4, DAT5, DAT6, LAST} ++ stmia D!, {DAT0, DAT1, DAT2, DAT3} ++ stmia D!, {DAT4, DAT5, DAT6, LAST} ++ .endif ++ .else ++ unaligned_words backwards, align, 0, 8, DAT0, DAT1, DAT2, DAT3, DAT4, DAT5, DAT6, DAT7, LAST ++ .endif ++ subs N, N, #32 ++ bhs 120b ++ tst N, #16 ++ .if align == 0 ++ .if backwards ++ ldmnedb S!, {DAT0, DAT1, DAT2, LAST} ++ stmnedb D!, {DAT0, DAT1, DAT2, LAST} ++ .else ++ ldmneia S!, {DAT0, DAT1, DAT2, LAST} ++ stmneia D!, {DAT0, DAT1, DAT2, LAST} ++ .endif ++ .else ++ beq 130f ++ unaligned_words backwards, align, 0, 4, DAT0, DAT1, DAT2, DAT3, LAST ++130: ++ .endif ++ /* Trailing words and bytes */ ++ tst N, #15 ++ beq 199f ++ .if align != 0 ++ add S, S, #align ++ .endif ++ memcpy_trailing_15bytes backwards, align ++199: ++ pop {DAT3, DAT4, DAT5, DAT6, DAT7} ++ pop {D, DAT1, DAT2, pc} ++.endm ++ ++.macro memcpy_medium_inner_loop backwards, align ++120: ++ .if backwards ++ .if align == 0 ++ ldmdb S!, {DAT0, DAT1, DAT2, LAST} ++ .else ++ ldr LAST, [S, #-4]! ++ ldr DAT2, [S, #-4]! ++ ldr DAT1, [S, #-4]! ++ ldr DAT0, [S, #-4]! ++ .endif ++ stmdb D!, {DAT0, DAT1, DAT2, LAST} ++ .else ++ .if align == 0 ++ ldmia S!, {DAT0, DAT1, DAT2, LAST} ++ .else ++ ldr DAT0, [S], #4 ++ ldr DAT1, [S], #4 ++ ldr DAT2, [S], #4 ++ ldr LAST, [S], #4 ++ .endif ++ stmia D!, {DAT0, DAT1, DAT2, LAST} ++ .endif ++ subs N, N, #16 ++ bhs 120b ++ /* Trailing words and bytes */ ++ tst N, #15 ++ beq 199f ++ memcpy_trailing_15bytes backwards, align ++199: ++ pop {D, DAT1, DAT2, pc} ++.endm ++ ++.macro memcpy_short_inner_loop backwards, align ++ tst N, #16 ++ .if backwards ++ .if align == 0 ++ ldmnedb S!, {DAT0, DAT1, DAT2, LAST} ++ .else ++ ldrne LAST, [S, #-4]! ++ ldrne DAT2, [S, #-4]! ++ ldrne DAT1, [S, #-4]! ++ ldrne DAT0, [S, #-4]! ++ .endif ++ stmnedb D!, {DAT0, DAT1, DAT2, LAST} ++ .else ++ .if align == 0 ++ ldmneia S!, {DAT0, DAT1, DAT2, LAST} ++ .else ++ ldrne DAT0, [S], #4 ++ ldrne DAT1, [S], #4 ++ ldrne DAT2, [S], #4 ++ ldrne LAST, [S], #4 ++ .endif ++ stmneia D!, {DAT0, DAT1, DAT2, LAST} ++ .endif ++ memcpy_trailing_15bytes backwards, align ++199: ++ pop {D, DAT1, DAT2, pc} ++.endm ++ ++.macro memcpy backwards ++ D .req a1 ++ S .req a2 ++ N .req a3 ++ DAT0 .req a4 ++ DAT1 .req v1 ++ DAT2 .req v2 ++ DAT3 .req v3 ++ DAT4 .req v4 ++ DAT5 .req v5 ++ DAT6 .req v6 ++ DAT7 .req sl ++ LAST .req ip ++ OFF .req lr ++ ++ .cfi_startproc ++ ++ push {D, DAT1, DAT2, lr} ++ ++ .cfi_def_cfa_offset 16 ++ .cfi_rel_offset D, 0 ++ .cfi_undefined S ++ .cfi_undefined N ++ .cfi_undefined DAT0 ++ .cfi_rel_offset DAT1, 4 ++ .cfi_rel_offset DAT2, 8 ++ .cfi_undefined LAST ++ .cfi_rel_offset lr, 12 ++ ++ .if backwards ++ add D, D, N ++ add S, S, N ++ .endif ++ ++ /* See if we're guaranteed to have at least one 16-byte aligned 16-byte write */ ++ cmp N, #31 ++ blo 170f ++ /* To preload ahead as we go, we need at least (prefetch_distance+2) 32-byte blocks */ ++ cmp N, #(prefetch_distance+3)*32 - 1 ++ blo 160f ++ ++ /* Long case */ ++ push {DAT3, DAT4, DAT5, DAT6, DAT7} ++ ++ .cfi_def_cfa_offset 36 ++ .cfi_rel_offset D, 20 ++ .cfi_rel_offset DAT1, 24 ++ .cfi_rel_offset DAT2, 28 ++ .cfi_rel_offset DAT3, 0 ++ .cfi_rel_offset DAT4, 4 ++ .cfi_rel_offset DAT5, 8 ++ .cfi_rel_offset DAT6, 12 ++ .cfi_rel_offset DAT7, 16 ++ .cfi_rel_offset lr, 32 ++ ++ /* Adjust N so that the decrement instruction can also test for ++ * inner loop termination. We want it to stop when there are ++ * (prefetch_distance+1) complete blocks to go. */ ++ sub N, N, #(prefetch_distance+2)*32 ++ preload_leading_step1 backwards, DAT0, S ++ .if backwards ++ /* Bug in GAS: it accepts, but mis-assembles the instruction ++ * ands DAT2, D, #60, 2 ++ * which sets DAT2 to the number of leading bytes until destination is aligned and also clears C (sets borrow) ++ */ ++ .word 0xE210513C ++ beq 154f ++ .else ++ ands DAT2, D, #15 ++ beq 154f ++ rsb DAT2, DAT2, #16 /* number of leading bytes until destination aligned */ ++ .endif ++ preload_leading_step2 backwards, DAT0, S, DAT2, OFF ++ memcpy_leading_15bytes backwards, 1 ++154: /* Destination now 16-byte aligned; we have at least one prefetch as well as at least one 16-byte output block */ ++ /* Prefetch offset is best selected such that it lies in the first 8 of each 32 bytes - but it's just as easy to aim for the first one */ ++ .if backwards ++ rsb OFF, S, #3 ++ and OFF, OFF, #28 ++ sub OFF, OFF, #32*(prefetch_distance+1) ++ .else ++ and OFF, S, #28 ++ rsb OFF, OFF, #32*prefetch_distance ++ .endif ++ movs DAT0, S, lsl #31 ++ bhi 157f ++ bcs 156f ++ bmi 155f ++ memcpy_long_inner_loop backwards, 0 ++155: memcpy_long_inner_loop backwards, 1 ++156: memcpy_long_inner_loop backwards, 2 ++157: memcpy_long_inner_loop backwards, 3 ++ ++ .cfi_def_cfa_offset 16 ++ .cfi_rel_offset D, 0 ++ .cfi_rel_offset DAT1, 4 ++ .cfi_rel_offset DAT2, 8 ++ .cfi_same_value DAT3 ++ .cfi_same_value DAT4 ++ .cfi_same_value DAT5 ++ .cfi_same_value DAT6 ++ .cfi_same_value DAT7 ++ .cfi_rel_offset lr, 12 ++ ++160: /* Medium case */ ++ preload_all backwards, 0, 0, S, N, DAT2, OFF ++ sub N, N, #16 /* simplifies inner loop termination */ ++ .if backwards ++ ands DAT2, D, #15 ++ beq 164f ++ .else ++ ands DAT2, D, #15 ++ beq 164f ++ rsb DAT2, DAT2, #16 ++ .endif ++ memcpy_leading_15bytes backwards, align ++164: /* Destination now 16-byte aligned; we have at least one 16-byte output block */ ++ tst S, #3 ++ bne 140f ++ memcpy_medium_inner_loop backwards, 0 ++140: memcpy_medium_inner_loop backwards, 1 ++ ++170: /* Short case, less than 31 bytes, so no guarantee of at least one 16-byte block */ ++ teq N, #0 ++ beq 199f ++ preload_all backwards, 1, 0, S, N, DAT2, LAST ++ tst D, #3 ++ beq 174f ++172: subs N, N, #1 ++ blo 199f ++ .if backwards ++ ldrb DAT0, [S, #-1]! ++ strb DAT0, [D, #-1]! ++ .else ++ ldrb DAT0, [S], #1 ++ strb DAT0, [D], #1 ++ .endif ++ tst D, #3 ++ bne 172b ++174: /* Destination now 4-byte aligned; we have 0 or more output bytes to go */ ++ tst S, #3 ++ bne 140f ++ memcpy_short_inner_loop backwards, 0 ++140: memcpy_short_inner_loop backwards, 1 ++ ++ .cfi_endproc ++ ++ .unreq D ++ .unreq S ++ .unreq N ++ .unreq DAT0 ++ .unreq DAT1 ++ .unreq DAT2 ++ .unreq DAT3 ++ .unreq DAT4 ++ .unreq DAT5 ++ .unreq DAT6 ++ .unreq DAT7 ++ .unreq LAST ++ .unreq OFF ++.endm +--- /dev/null ++++ b/arch/arm/lib/memmove_rpi.S +@@ -0,0 +1,61 @@ ++/* ++Copyright (c) 2013, Raspberry Pi Foundation ++Copyright (c) 2013, RISC OS Open Ltd ++All rights reserved. ++ ++Redistribution and use in source and binary forms, with or without ++modification, are permitted provided that the following conditions are met: ++ * Redistributions of source code must retain the above copyright ++ notice, this list of conditions and the following disclaimer. ++ * Redistributions in binary form must reproduce the above copyright ++ notice, this list of conditions and the following disclaimer in the ++ documentation and/or other materials provided with the distribution. ++ * Neither the name of the copyright holder nor the ++ names of its contributors may be used to endorse or promote products ++ derived from this software without specific prior written permission. ++ ++THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ++ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED ++WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE ++DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY ++DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; ++LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ++ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++*/ ++ ++#include ++#include "arm-mem.h" ++#include "memcpymove.h" ++ ++/* Prevent the stack from becoming executable */ ++#if defined(__linux__) && defined(__ELF__) ++.section .note.GNU-stack,"",%progbits ++#endif ++ ++ .text ++ .arch armv6 ++ .object_arch armv4 ++ .arm ++ .altmacro ++ .p2align 2 ++ ++/* ++ * void *memmove(void *s1, const void *s2, size_t n); ++ * On entry: ++ * a1 = pointer to destination ++ * a2 = pointer to source ++ * a3 = number of bytes to copy ++ * On exit: ++ * a1 preserved ++ */ ++ ++.set prefetch_distance, 3 ++ ++ENTRY(memmove) ++ cmp a2, a1 ++ bpl memcpy /* pl works even over -1 - 0 and 0x7fffffff - 0x80000000 boundaries */ ++ memcpy 1 ++ENDPROC(memmove) +--- /dev/null ++++ b/arch/arm/lib/memset_rpi.S +@@ -0,0 +1,128 @@ ++/* ++Copyright (c) 2013, Raspberry Pi Foundation ++Copyright (c) 2013, RISC OS Open Ltd ++All rights reserved. ++ ++Redistribution and use in source and binary forms, with or without ++modification, are permitted provided that the following conditions are met: ++ * Redistributions of source code must retain the above copyright ++ notice, this list of conditions and the following disclaimer. ++ * Redistributions in binary form must reproduce the above copyright ++ notice, this list of conditions and the following disclaimer in the ++ documentation and/or other materials provided with the distribution. ++ * Neither the name of the copyright holder nor the ++ names of its contributors may be used to endorse or promote products ++ derived from this software without specific prior written permission. ++ ++THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ++ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED ++WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE ++DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY ++DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES ++(INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; ++LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ++ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT ++(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++*/ ++ ++#include ++#include "arm-mem.h" ++ ++/* Prevent the stack from becoming executable */ ++#if defined(__linux__) && defined(__ELF__) ++.section .note.GNU-stack,"",%progbits ++#endif ++ ++ .text ++ .arch armv6 ++ .object_arch armv4 ++ .arm ++ .altmacro ++ .p2align 2 ++ ++/* ++ * void *memset(void *s, int c, size_t n); ++ * On entry: ++ * a1 = pointer to buffer to fill ++ * a2 = byte pattern to fill with (caller-narrowed) ++ * a3 = number of bytes to fill ++ * On exit: ++ * a1 preserved ++ */ ++ENTRY(mmioset) ++ENTRY(memset) ++ENTRY(__memset32) ++ENTRY(__memset64) ++ ++ S .req a1 ++ DAT0 .req a2 ++ N .req a3 ++ DAT1 .req a4 ++ DAT2 .req ip ++ DAT3 .req lr ++ ++ orr DAT0, DAT0, DAT0, lsl #8 ++ push {S, lr} ++ orr DAT0, DAT0, DAT0, lsl #16 ++ mov DAT1, DAT0 ++ ++ /* See if we're guaranteed to have at least one 16-byte aligned 16-byte write */ ++ cmp N, #31 ++ blo 170f ++ ++161: sub N, N, #16 /* simplifies inner loop termination */ ++ /* Leading words and bytes */ ++ tst S, #15 ++ beq 164f ++ rsb DAT3, S, #0 /* bits 0-3 = number of leading bytes until aligned */ ++ movs DAT2, DAT3, lsl #31 ++ submi N, N, #1 ++ strmib DAT0, [S], #1 ++ subcs N, N, #2 ++ strcsh DAT0, [S], #2 ++ movs DAT2, DAT3, lsl #29 ++ submi N, N, #4 ++ strmi DAT0, [S], #4 ++ subcs N, N, #8 ++ stmcsia S!, {DAT0, DAT1} ++164: /* Delayed set up of DAT2 and DAT3 so we could use them as scratch registers above */ ++ mov DAT2, DAT0 ++ mov DAT3, DAT0 ++ /* Now the inner loop of 16-byte stores */ ++165: stmia S!, {DAT0, DAT1, DAT2, DAT3} ++ subs N, N, #16 ++ bhs 165b ++166: /* Trailing words and bytes */ ++ movs N, N, lsl #29 ++ stmcsia S!, {DAT0, DAT1} ++ strmi DAT0, [S], #4 ++ movs N, N, lsl #2 ++ strcsh DAT0, [S], #2 ++ strmib DAT0, [S] ++199: pop {S, pc} ++ ++170: /* Short case */ ++ mov DAT2, DAT0 ++ mov DAT3, DAT0 ++ tst S, #3 ++ beq 174f ++172: subs N, N, #1 ++ blo 199b ++ strb DAT0, [S], #1 ++ tst S, #3 ++ bne 172b ++174: tst N, #16 ++ stmneia S!, {DAT0, DAT1, DAT2, DAT3} ++ b 166b ++ ++ .unreq S ++ .unreq DAT0 ++ .unreq N ++ .unreq DAT1 ++ .unreq DAT2 ++ .unreq DAT3 ++ENDPROC(__memset64) ++ENDPROC(__memset32) ++ENDPROC(memset) ++ENDPROC(mmioset) +--- a/arch/arm/lib/uaccess_with_memcpy.c ++++ b/arch/arm/lib/uaccess_with_memcpy.c +@@ -19,6 +19,14 @@ + #include + #include + ++#ifndef COPY_FROM_USER_THRESHOLD ++#define COPY_FROM_USER_THRESHOLD 64 ++#endif ++ ++#ifndef COPY_TO_USER_THRESHOLD ++#define COPY_TO_USER_THRESHOLD 64 ++#endif ++ + static int + pin_page_for_write(const void __user *_addr, pte_t **ptep, spinlock_t **ptlp) + { +@@ -43,7 +51,7 @@ pin_page_for_write(const void __user *_a + return 0; + + pmd = pmd_offset(pud, addr); +- if (unlikely(pmd_none(*pmd))) ++ if (unlikely(pmd_none(*pmd) || pmd_bad(*pmd))) + return 0; + + /* +@@ -86,7 +94,46 @@ pin_page_for_write(const void __user *_a + return 1; + } + +-static unsigned long noinline ++static int ++pin_page_for_read(const void __user *_addr, pte_t **ptep, spinlock_t **ptlp) ++{ ++ unsigned long addr = (unsigned long)_addr; ++ pgd_t *pgd; ++ p4d_t *p4d; ++ pmd_t *pmd; ++ pte_t *pte; ++ pud_t *pud; ++ spinlock_t *ptl; ++ ++ pgd = pgd_offset(current->mm, addr); ++ if (unlikely(pgd_none(*pgd) || pgd_bad(*pgd))) ++ return 0; ++ ++ p4d = p4d_offset(pgd, addr); ++ if (unlikely(p4d_none(*p4d) || p4d_bad(*p4d))) ++ return 0; ++ ++ pud = pud_offset(p4d, addr); ++ if (unlikely(pud_none(*pud) || pud_bad(*pud))) ++ return 0; ++ ++ pmd = pmd_offset(pud, addr); ++ if (unlikely(pmd_none(*pmd) || pmd_bad(*pmd))) ++ return 0; ++ ++ pte = pte_offset_map_lock(current->mm, pmd, addr, &ptl); ++ if (unlikely(!pte_present(*pte) || !pte_young(*pte))) { ++ pte_unmap_unlock(pte, ptl); ++ return 0; ++ } ++ ++ *ptep = pte; ++ *ptlp = ptl; ++ ++ return 1; ++} ++ ++unsigned long noinline + __copy_to_user_memcpy(void __user *to, const void *from, unsigned long n) + { + unsigned long ua_flags; +@@ -139,6 +186,57 @@ out: + return n; + } + ++unsigned long noinline ++__copy_from_user_memcpy(void *to, const void __user *from, unsigned long n) ++{ ++ unsigned long ua_flags; ++ int atomic; ++ ++ if (unlikely(uaccess_kernel())) { ++ memcpy(to, (const void *)from, n); ++ return 0; ++ } ++ ++ /* the mmap semaphore is taken only if not in an atomic context */ ++ atomic = in_atomic(); ++ ++ if (!atomic) ++ mmap_read_lock(current->mm); ++ while (n) { ++ pte_t *pte; ++ spinlock_t *ptl; ++ int tocopy; ++ ++ while (!pin_page_for_read(from, &pte, &ptl)) { ++ char temp; ++ if (!atomic) ++ mmap_read_unlock(current->mm); ++ if (__get_user(temp, (char __user *)from)) ++ goto out; ++ if (!atomic) ++ mmap_read_lock(current->mm); ++ } ++ ++ tocopy = (~(unsigned long)from & ~PAGE_MASK) + 1; ++ if (tocopy > n) ++ tocopy = n; ++ ++ ua_flags = uaccess_save_and_enable(); ++ memcpy(to, (const void *)from, tocopy); ++ uaccess_restore(ua_flags); ++ to += tocopy; ++ from += tocopy; ++ n -= tocopy; ++ ++ pte_unmap_unlock(pte, ptl); ++ } ++ if (!atomic) ++ mmap_read_unlock(current->mm); ++ ++out: ++ return n; ++} ++ + unsigned long + arm_copy_to_user(void __user *to, const void *from, unsigned long n) + { +@@ -149,7 +247,7 @@ arm_copy_to_user(void __user *to, const + * With frame pointer disabled, tail call optimization kicks in + * as well making this test almost invisible. + */ +- if (n < 64) { ++ if (n < COPY_TO_USER_THRESHOLD) { + unsigned long ua_flags = uaccess_save_and_enable(); + n = __copy_to_user_std(to, from, n); + uaccess_restore(ua_flags); +@@ -159,6 +257,32 @@ arm_copy_to_user(void __user *to, const + } + return n; + } ++ ++unsigned long __must_check ++arm_copy_from_user(void *to, const void __user *from, unsigned long n) ++{ ++#ifdef CONFIG_BCM2835_FAST_MEMCPY ++ /* ++ * This test is stubbed out of the main function above to keep ++ * the overhead for small copies low by avoiding a large ++ * register dump on the stack just to reload them right away. ++ * With frame pointer disabled, tail call optimization kicks in ++ * as well making this test almost invisible. ++ */ ++ if (n < COPY_TO_USER_THRESHOLD) { ++ unsigned long ua_flags = uaccess_save_and_enable(); ++ n = __copy_from_user_std(to, from, n); ++ uaccess_restore(ua_flags); ++ } else { ++ n = __copy_from_user_memcpy(to, from, n); ++ } ++#else ++ unsigned long ua_flags = uaccess_save_and_enable(); ++ n = __copy_from_user_std(to, from, n); ++ uaccess_restore(ua_flags); ++#endif ++ return n; ++} + + static unsigned long noinline + __clear_user_memset(void __user *addr, unsigned long n) +--- a/arch/arm/mach-bcm/Kconfig ++++ b/arch/arm/mach-bcm/Kconfig +@@ -184,6 +184,13 @@ config ARCH_BCM_53573 + The base chip is BCM53573 and there are some packaging modifications + like BCM47189 and BCM47452. + ++config BCM2835_FAST_MEMCPY ++ bool "Enable optimized __copy_to_user and __copy_from_user" ++ depends on ARCH_BCM2835 && ARCH_MULTI_V6 ++ default y ++ help ++ Optimized versions of __copy_to_user and __copy_from_user for Pi1. ++ + config ARCH_BCM_63XX + bool "Broadcom BCM63xx DSL SoC" + depends on ARCH_MULTI_V7 diff --git a/target/linux/bcm27xx/patches-5.10/950-0058-gpio-poweroff-Allow-it-to-work-on-Raspberry-Pi.patch b/target/linux/bcm27xx/patches-5.10/950-0058-gpio-poweroff-Allow-it-to-work-on-Raspberry-Pi.patch new file mode 100644 index 0000000000..5d0873bd29 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0058-gpio-poweroff-Allow-it-to-work-on-Raspberry-Pi.patch @@ -0,0 +1,35 @@ +From 95a7bcf89e17aa8ec8cabc06d47479e1ecb76976 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 25 Jun 2015 12:16:11 +0100 +Subject: [PATCH] gpio-poweroff: Allow it to work on Raspberry Pi + +The Raspberry Pi firmware manages the power-down and reboot +process. To do this it installs a pm_power_off handler, causing +the gpio-poweroff module to abort the probe function. + +This patch introduces a "force" DT property that overrides that +behaviour, and also adds a DT overlay to enable and control it. + +Note that running in an active-low configuration (DT parameter +"active_low") requires a custom dt-blob.bin and probably won't +allow a reboot without switching off, so an external inversion +of the trigger signal may be preferable. +--- + drivers/power/reset/gpio-poweroff.c | 4 +++- + 1 file changed, 3 insertions(+), 1 deletion(-) + +--- a/drivers/power/reset/gpio-poweroff.c ++++ b/drivers/power/reset/gpio-poweroff.c +@@ -50,9 +50,11 @@ static int gpio_poweroff_probe(struct pl + { + bool input = false; + enum gpiod_flags flags; ++ bool force = false; + + /* If a pm_power_off function has already been added, leave it alone */ +- if (pm_power_off != NULL) { ++ force = of_property_read_bool(pdev->dev.of_node, "force"); ++ if (!force && (pm_power_off != NULL)) { + dev_err(&pdev->dev, + "%s: pm_power_off function already registered\n", + __func__); diff --git a/target/linux/bcm27xx/patches-5.10/950-0059-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch b/target/linux/bcm27xx/patches-5.10/950-0059-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch new file mode 100644 index 0000000000..bb4c686489 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0059-mfd-Add-Raspberry-Pi-Sense-HAT-core-driver.patch @@ -0,0 +1,852 @@ +From cf000173e9ee4a80ac245e5feb042c18c5643d6c Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 14 Jul 2015 14:32:47 +0100 +Subject: [PATCH] mfd: Add Raspberry Pi Sense HAT core driver + +mfd: Add rpi_sense_core of compatible string +--- + drivers/input/joystick/Kconfig | 8 + + drivers/input/joystick/Makefile | 2 +- + drivers/input/joystick/rpisense-js.c | 153 ++++++++++++ + drivers/mfd/Kconfig | 8 + + drivers/mfd/Makefile | 1 + + drivers/mfd/rpisense-core.c | 165 +++++++++++++ + drivers/video/fbdev/Kconfig | 13 + + drivers/video/fbdev/Makefile | 1 + + drivers/video/fbdev/rpisense-fb.c | 293 +++++++++++++++++++++++ + include/linux/mfd/rpisense/core.h | 47 ++++ + include/linux/mfd/rpisense/framebuffer.h | 32 +++ + include/linux/mfd/rpisense/joystick.h | 35 +++ + 12 files changed, 757 insertions(+), 1 deletion(-) + create mode 100644 drivers/input/joystick/rpisense-js.c + create mode 100644 drivers/mfd/rpisense-core.c + create mode 100644 drivers/video/fbdev/rpisense-fb.c + create mode 100644 include/linux/mfd/rpisense/core.h + create mode 100644 include/linux/mfd/rpisense/framebuffer.h + create mode 100644 include/linux/mfd/rpisense/joystick.h + +--- a/drivers/input/joystick/Kconfig ++++ b/drivers/input/joystick/Kconfig +@@ -382,4 +382,12 @@ config JOYSTICK_FSIA6B + To compile this driver as a module, choose M here: the + module will be called fsia6b. + ++config JOYSTICK_RPISENSE ++ tristate "Raspberry Pi Sense HAT joystick" ++ depends on GPIOLIB && INPUT ++ select MFD_RPISENSE_CORE ++ ++ help ++ This is the joystick driver for the Raspberry Pi Sense HAT ++ + endif +--- a/drivers/input/joystick/Makefile ++++ b/drivers/input/joystick/Makefile +@@ -37,4 +37,4 @@ obj-$(CONFIG_JOYSTICK_WARRIOR) += warri + obj-$(CONFIG_JOYSTICK_WALKERA0701) += walkera0701.o + obj-$(CONFIG_JOYSTICK_XPAD) += xpad.o + obj-$(CONFIG_JOYSTICK_ZHENHUA) += zhenhua.o +- ++obj-$(CONFIG_JOYSTICK_RPISENSE) += rpisense-js.o +--- /dev/null ++++ b/drivers/input/joystick/rpisense-js.c +@@ -0,0 +1,153 @@ ++/* ++ * Raspberry Pi Sense HAT joystick driver ++ * http://raspberrypi.org ++ * ++ * Copyright (C) 2015 Raspberry Pi ++ * ++ * Author: Serge Schneider ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License as published by the ++ * Free Software Foundation; either version 2 of the License, or (at your ++ * option) any later version. ++ * ++ */ ++ ++#include ++ ++#include ++#include ++ ++static struct rpisense *rpisense; ++static unsigned char keymap[5] = {KEY_DOWN, KEY_RIGHT, KEY_UP, KEY_ENTER, KEY_LEFT,}; ++ ++static void keys_work_fn(struct work_struct *work) ++{ ++ int i; ++ static s32 prev_keys; ++ struct rpisense_js *rpisense_js = &rpisense->joystick; ++ s32 keys = rpisense_reg_read(rpisense, RPISENSE_KEYS); ++ s32 changes = keys ^ prev_keys; ++ ++ prev_keys = keys; ++ for (i = 0; i < 5; i++) { ++ if (changes & 1) { ++ input_report_key(rpisense_js->keys_dev, ++ keymap[i], keys & 1); ++ } ++ changes >>= 1; ++ keys >>= 1; ++ } ++ input_sync(rpisense_js->keys_dev); ++} ++ ++static irqreturn_t keys_irq_handler(int irq, void *pdev) ++{ ++ struct rpisense_js *rpisense_js = &rpisense->joystick; ++ ++ schedule_work(&rpisense_js->keys_work_s); ++ return IRQ_HANDLED; ++} ++ ++static int rpisense_js_probe(struct platform_device *pdev) ++{ ++ int ret; ++ int i; ++ struct rpisense_js *rpisense_js; ++ ++ rpisense = rpisense_get_dev(); ++ rpisense_js = &rpisense->joystick; ++ ++ INIT_WORK(&rpisense_js->keys_work_s, keys_work_fn); ++ ++ rpisense_js->keys_dev = input_allocate_device(); ++ if (!rpisense_js->keys_dev) { ++ dev_err(&pdev->dev, "Could not allocate input device.\n"); ++ return -ENOMEM; ++ } ++ ++ rpisense_js->keys_dev->evbit[0] = BIT_MASK(EV_KEY); ++ for (i = 0; i < ARRAY_SIZE(keymap); i++) { ++ set_bit(keymap[i], ++ rpisense_js->keys_dev->keybit); ++ } ++ ++ rpisense_js->keys_dev->name = "Raspberry Pi Sense HAT Joystick"; ++ rpisense_js->keys_dev->phys = "rpi-sense-joy/input0"; ++ rpisense_js->keys_dev->id.bustype = BUS_I2C; ++ rpisense_js->keys_dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_REP); ++ rpisense_js->keys_dev->keycode = keymap; ++ rpisense_js->keys_dev->keycodesize = sizeof(unsigned char); ++ rpisense_js->keys_dev->keycodemax = ARRAY_SIZE(keymap); ++ ++ ret = input_register_device(rpisense_js->keys_dev); ++ if (ret) { ++ dev_err(&pdev->dev, "Could not register input device.\n"); ++ goto err_keys_alloc; ++ } ++ ++ ret = gpiod_direction_input(rpisense_js->keys_desc); ++ if (ret) { ++ dev_err(&pdev->dev, "Could not set keys-int direction.\n"); ++ goto err_keys_reg; ++ } ++ ++ rpisense_js->keys_irq = gpiod_to_irq(rpisense_js->keys_desc); ++ if (rpisense_js->keys_irq < 0) { ++ dev_err(&pdev->dev, "Could not determine keys-int IRQ.\n"); ++ ret = rpisense_js->keys_irq; ++ goto err_keys_reg; ++ } ++ ++ ret = devm_request_irq(&pdev->dev, rpisense_js->keys_irq, ++ keys_irq_handler, IRQF_TRIGGER_RISING, ++ "keys", &pdev->dev); ++ if (ret) { ++ dev_err(&pdev->dev, "IRQ request failed.\n"); ++ goto err_keys_reg; ++ } ++ return 0; ++err_keys_reg: ++ input_unregister_device(rpisense_js->keys_dev); ++err_keys_alloc: ++ input_free_device(rpisense_js->keys_dev); ++ return ret; ++} ++ ++static int rpisense_js_remove(struct platform_device *pdev) ++{ ++ struct rpisense_js *rpisense_js = &rpisense->joystick; ++ ++ input_unregister_device(rpisense_js->keys_dev); ++ input_free_device(rpisense_js->keys_dev); ++ return 0; ++} ++ ++#ifdef CONFIG_OF ++static const struct of_device_id rpisense_js_id[] = { ++ { .compatible = "rpi,rpi-sense-js" }, ++ { }, ++}; ++MODULE_DEVICE_TABLE(of, rpisense_js_id); ++#endif ++ ++static struct platform_device_id rpisense_js_device_id[] = { ++ { .name = "rpi-sense-js" }, ++ { }, ++}; ++MODULE_DEVICE_TABLE(platform, rpisense_js_device_id); ++ ++static struct platform_driver rpisense_js_driver = { ++ .probe = rpisense_js_probe, ++ .remove = rpisense_js_remove, ++ .driver = { ++ .name = "rpi-sense-js", ++ .owner = THIS_MODULE, ++ }, ++}; ++ ++module_platform_driver(rpisense_js_driver); ++ ++MODULE_DESCRIPTION("Raspberry Pi Sense HAT joystick driver"); ++MODULE_AUTHOR("Serge Schneider "); ++MODULE_LICENSE("GPL"); +--- a/drivers/mfd/Kconfig ++++ b/drivers/mfd/Kconfig +@@ -11,6 +11,14 @@ config MFD_CORE + select IRQ_DOMAIN + default n + ++config MFD_RPISENSE_CORE ++ tristate "Raspberry Pi Sense HAT core functions" ++ depends on I2C ++ select MFD_CORE ++ help ++ This is the core driver for the Raspberry Pi Sense HAT. This provides ++ the necessary functions to communicate with the hardware. ++ + config MFD_CS5535 + tristate "AMD CS5535 and CS5536 southbridge core functions" + select MFD_CORE +--- a/drivers/mfd/Makefile ++++ b/drivers/mfd/Makefile +@@ -263,6 +263,7 @@ obj-$(CONFIG_MFD_ROHM_BD71828) += rohm-b + obj-$(CONFIG_MFD_ROHM_BD718XX) += rohm-bd718x7.o + obj-$(CONFIG_MFD_STMFX) += stmfx.o + obj-$(CONFIG_MFD_KHADAS_MCU) += khadas-mcu.o ++obj-$(CONFIG_MFD_RPISENSE_CORE) += rpisense-core.o + + obj-$(CONFIG_SGI_MFD_IOC3) += ioc3.o + obj-$(CONFIG_MFD_SIMPLE_MFD_I2C) += simple-mfd-i2c.o +--- /dev/null ++++ b/drivers/mfd/rpisense-core.c +@@ -0,0 +1,165 @@ ++/* ++ * Raspberry Pi Sense HAT core driver ++ * http://raspberrypi.org ++ * ++ * Copyright (C) 2015 Raspberry Pi ++ * ++ * Author: Serge Schneider ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License as published by the ++ * Free Software Foundation; either version 2 of the License, or (at your ++ * option) any later version. ++ * ++ * This driver is based on wm8350 implementation. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++static struct rpisense *rpisense; ++ ++static void rpisense_client_dev_register(struct rpisense *rpisense, ++ const char *name, ++ struct platform_device **pdev) ++{ ++ int ret; ++ ++ *pdev = platform_device_alloc(name, -1); ++ if (*pdev == NULL) { ++ dev_err(rpisense->dev, "Failed to allocate %s\n", name); ++ return; ++ } ++ ++ (*pdev)->dev.parent = rpisense->dev; ++ platform_set_drvdata(*pdev, rpisense); ++ ret = platform_device_add(*pdev); ++ if (ret != 0) { ++ dev_err(rpisense->dev, "Failed to register %s: %d\n", ++ name, ret); ++ platform_device_put(*pdev); ++ *pdev = NULL; ++ } ++} ++ ++static int rpisense_probe(struct i2c_client *i2c, ++ const struct i2c_device_id *id) ++{ ++ int ret; ++ struct rpisense_js *rpisense_js; ++ ++ rpisense = devm_kzalloc(&i2c->dev, sizeof(struct rpisense), GFP_KERNEL); ++ if (rpisense == NULL) ++ return -ENOMEM; ++ ++ i2c_set_clientdata(i2c, rpisense); ++ rpisense->dev = &i2c->dev; ++ rpisense->i2c_client = i2c; ++ ++ ret = rpisense_reg_read(rpisense, RPISENSE_WAI); ++ if (ret > 0) { ++ if (ret != 's') ++ return -EINVAL; ++ } else { ++ return ret; ++ } ++ ret = rpisense_reg_read(rpisense, RPISENSE_VER); ++ if (ret < 0) ++ return ret; ++ ++ dev_info(rpisense->dev, ++ "Raspberry Pi Sense HAT firmware version %i\n", ret); ++ ++ rpisense_js = &rpisense->joystick; ++ rpisense_js->keys_desc = devm_gpiod_get(&i2c->dev, ++ "keys-int", GPIOD_IN); ++ if (IS_ERR(rpisense_js->keys_desc)) { ++ dev_warn(&i2c->dev, "Failed to get keys-int descriptor.\n"); ++ rpisense_js->keys_desc = gpio_to_desc(23); ++ if (rpisense_js->keys_desc == NULL) { ++ dev_err(&i2c->dev, "GPIO23 fallback failed.\n"); ++ return PTR_ERR(rpisense_js->keys_desc); ++ } ++ } ++ rpisense_client_dev_register(rpisense, "rpi-sense-js", ++ &(rpisense->joystick.pdev)); ++ rpisense_client_dev_register(rpisense, "rpi-sense-fb", ++ &(rpisense->framebuffer.pdev)); ++ ++ return 0; ++} ++ ++static int rpisense_remove(struct i2c_client *i2c) ++{ ++ struct rpisense *rpisense = i2c_get_clientdata(i2c); ++ ++ platform_device_unregister(rpisense->joystick.pdev); ++ return 0; ++} ++ ++struct rpisense *rpisense_get_dev(void) ++{ ++ return rpisense; ++} ++EXPORT_SYMBOL_GPL(rpisense_get_dev); ++ ++s32 rpisense_reg_read(struct rpisense *rpisense, int reg) ++{ ++ int ret = i2c_smbus_read_byte_data(rpisense->i2c_client, reg); ++ ++ if (ret < 0) ++ dev_err(rpisense->dev, "Read from reg %d failed\n", reg); ++ /* Due to the BCM270x I2C clock stretching bug, some values ++ * may have MSB set. Clear it to avoid incorrect values. ++ * */ ++ return ret & 0x7F; ++} ++EXPORT_SYMBOL_GPL(rpisense_reg_read); ++ ++int rpisense_block_write(struct rpisense *rpisense, const char *buf, int count) ++{ ++ int ret = i2c_master_send(rpisense->i2c_client, buf, count); ++ ++ if (ret < 0) ++ dev_err(rpisense->dev, "Block write failed\n"); ++ return ret; ++} ++EXPORT_SYMBOL_GPL(rpisense_block_write); ++ ++static const struct i2c_device_id rpisense_i2c_id[] = { ++ { "rpi-sense", 0 }, ++ { } ++}; ++MODULE_DEVICE_TABLE(i2c, rpisense_i2c_id); ++ ++#ifdef CONFIG_OF ++static const struct of_device_id rpisense_core_id[] = { ++ { .compatible = "rpi,rpi-sense" }, ++ { }, ++}; ++MODULE_DEVICE_TABLE(of, rpisense_core_id); ++#endif ++ ++ ++static struct i2c_driver rpisense_driver = { ++ .driver = { ++ .name = "rpi-sense", ++ .owner = THIS_MODULE, ++ }, ++ .probe = rpisense_probe, ++ .remove = rpisense_remove, ++ .id_table = rpisense_i2c_id, ++}; ++ ++module_i2c_driver(rpisense_driver); ++ ++MODULE_DESCRIPTION("Raspberry Pi Sense HAT core driver"); ++MODULE_AUTHOR("Serge Schneider "); ++MODULE_LICENSE("GPL"); ++ +--- a/drivers/video/fbdev/Kconfig ++++ b/drivers/video/fbdev/Kconfig +@@ -2250,6 +2250,19 @@ config FB_SM712 + called sm712fb. If you want to compile it as a module, say M + here and read . + ++config FB_RPISENSE ++ tristate "Raspberry Pi Sense HAT framebuffer" ++ depends on FB ++ select MFD_RPISENSE_CORE ++ select FB_SYS_FOPS ++ select FB_SYS_FILLRECT ++ select FB_SYS_COPYAREA ++ select FB_SYS_IMAGEBLIT ++ select FB_DEFERRED_IO ++ ++ help ++ This is the framebuffer driver for the Raspberry Pi Sense HAT ++ + source "drivers/video/fbdev/omap/Kconfig" + source "drivers/video/fbdev/omap2/Kconfig" + source "drivers/video/fbdev/mmp/Kconfig" +--- a/drivers/video/fbdev/Makefile ++++ b/drivers/video/fbdev/Makefile +@@ -130,6 +130,7 @@ obj-$(CONFIG_FB_MX3) += mx3fb.o + obj-$(CONFIG_FB_DA8XX) += da8xx-fb.o + obj-$(CONFIG_FB_SSD1307) += ssd1307fb.o + obj-$(CONFIG_FB_SIMPLE) += simplefb.o ++obj-$(CONFIG_FB_RPISENSE) += rpisense-fb.o + + # the test framebuffer is last + obj-$(CONFIG_FB_VIRTUAL) += vfb.o +--- /dev/null ++++ b/drivers/video/fbdev/rpisense-fb.c +@@ -0,0 +1,293 @@ ++/* ++ * Raspberry Pi Sense HAT framebuffer driver ++ * http://raspberrypi.org ++ * ++ * Copyright (C) 2015 Raspberry Pi ++ * ++ * Author: Serge Schneider ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License as published by the ++ * Free Software Foundation; either version 2 of the License, or (at your ++ * option) any later version. ++ * ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++ ++static bool lowlight; ++module_param(lowlight, bool, 0); ++MODULE_PARM_DESC(lowlight, "Reduce LED matrix brightness to one third"); ++ ++static struct rpisense *rpisense; ++ ++struct rpisense_fb_param { ++ char __iomem *vmem; ++ u8 *vmem_work; ++ u32 vmemsize; ++ u8 *gamma; ++}; ++ ++static u8 gamma_default[32] = {0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x01, ++ 0x02, 0x02, 0x03, 0x03, 0x04, 0x05, 0x06, 0x07, ++ 0x08, 0x09, 0x0A, 0x0B, 0x0C, 0x0E, 0x0F, 0x11, ++ 0x12, 0x14, 0x15, 0x17, 0x19, 0x1B, 0x1D, 0x1F,}; ++ ++static u8 gamma_low[32] = {0x00, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, ++ 0x01, 0x01, 0x01, 0x01, 0x01, 0x02, 0x02, 0x02, ++ 0x03, 0x03, 0x03, 0x04, 0x04, 0x05, 0x05, 0x06, ++ 0x06, 0x07, 0x07, 0x08, 0x08, 0x09, 0x0A, 0x0A,}; ++ ++static u8 gamma_user[32]; ++ ++static struct rpisense_fb_param rpisense_fb_param = { ++ .vmem = NULL, ++ .vmemsize = 128, ++ .gamma = gamma_default, ++}; ++ ++static struct fb_deferred_io rpisense_fb_defio; ++ ++static struct fb_fix_screeninfo rpisense_fb_fix = { ++ .id = "RPi-Sense FB", ++ .type = FB_TYPE_PACKED_PIXELS, ++ .visual = FB_VISUAL_TRUECOLOR, ++ .xpanstep = 0, ++ .ypanstep = 0, ++ .ywrapstep = 0, ++ .accel = FB_ACCEL_NONE, ++ .line_length = 16, ++}; ++ ++static struct fb_var_screeninfo rpisense_fb_var = { ++ .xres = 8, ++ .yres = 8, ++ .xres_virtual = 8, ++ .yres_virtual = 8, ++ .bits_per_pixel = 16, ++ .red = {11, 5, 0}, ++ .green = {5, 6, 0}, ++ .blue = {0, 5, 0}, ++}; ++ ++static ssize_t rpisense_fb_write(struct fb_info *info, ++ const char __user *buf, size_t count, ++ loff_t *ppos) ++{ ++ ssize_t res = fb_sys_write(info, buf, count, ppos); ++ ++ schedule_delayed_work(&info->deferred_work, rpisense_fb_defio.delay); ++ return res; ++} ++ ++static void rpisense_fb_fillrect(struct fb_info *info, ++ const struct fb_fillrect *rect) ++{ ++ sys_fillrect(info, rect); ++ schedule_delayed_work(&info->deferred_work, rpisense_fb_defio.delay); ++} ++ ++static void rpisense_fb_copyarea(struct fb_info *info, ++ const struct fb_copyarea *area) ++{ ++ sys_copyarea(info, area); ++ schedule_delayed_work(&info->deferred_work, rpisense_fb_defio.delay); ++} ++ ++static void rpisense_fb_imageblit(struct fb_info *info, ++ const struct fb_image *image) ++{ ++ sys_imageblit(info, image); ++ schedule_delayed_work(&info->deferred_work, rpisense_fb_defio.delay); ++} ++ ++static void rpisense_fb_deferred_io(struct fb_info *info, ++ struct list_head *pagelist) ++{ ++ int i; ++ int j; ++ u8 *vmem_work = rpisense_fb_param.vmem_work; ++ u16 *mem = (u16 *)rpisense_fb_param.vmem; ++ u8 *gamma = rpisense_fb_param.gamma; ++ ++ vmem_work[0] = 0; ++ for (j = 0; j < 8; j++) { ++ for (i = 0; i < 8; i++) { ++ vmem_work[(j * 24) + i + 1] = ++ gamma[(mem[(j * 8) + i] >> 11) & 0x1F]; ++ vmem_work[(j * 24) + (i + 8) + 1] = ++ gamma[(mem[(j * 8) + i] >> 6) & 0x1F]; ++ vmem_work[(j * 24) + (i + 16) + 1] = ++ gamma[(mem[(j * 8) + i]) & 0x1F]; ++ } ++ } ++ rpisense_block_write(rpisense, vmem_work, 193); ++} ++ ++static struct fb_deferred_io rpisense_fb_defio = { ++ .delay = HZ/100, ++ .deferred_io = rpisense_fb_deferred_io, ++}; ++ ++static int rpisense_fb_ioctl(struct fb_info *info, unsigned int cmd, ++ unsigned long arg) ++{ ++ switch (cmd) { ++ case SENSEFB_FBIOGET_GAMMA: ++ if (copy_to_user((void __user *) arg, rpisense_fb_param.gamma, ++ sizeof(u8[32]))) ++ return -EFAULT; ++ return 0; ++ case SENSEFB_FBIOSET_GAMMA: ++ if (copy_from_user(gamma_user, (void __user *)arg, ++ sizeof(u8[32]))) ++ return -EFAULT; ++ rpisense_fb_param.gamma = gamma_user; ++ schedule_delayed_work(&info->deferred_work, ++ rpisense_fb_defio.delay); ++ return 0; ++ case SENSEFB_FBIORESET_GAMMA: ++ switch (arg) { ++ case 0: ++ rpisense_fb_param.gamma = gamma_default; ++ break; ++ case 1: ++ rpisense_fb_param.gamma = gamma_low; ++ break; ++ case 2: ++ rpisense_fb_param.gamma = gamma_user; ++ break; ++ default: ++ return -EINVAL; ++ } ++ schedule_delayed_work(&info->deferred_work, ++ rpisense_fb_defio.delay); ++ break; ++ default: ++ return -EINVAL; ++ } ++ return 0; ++} ++ ++static struct fb_ops rpisense_fb_ops = { ++ .owner = THIS_MODULE, ++ .fb_read = fb_sys_read, ++ .fb_write = rpisense_fb_write, ++ .fb_fillrect = rpisense_fb_fillrect, ++ .fb_copyarea = rpisense_fb_copyarea, ++ .fb_imageblit = rpisense_fb_imageblit, ++ .fb_ioctl = rpisense_fb_ioctl, ++}; ++ ++static int rpisense_fb_probe(struct platform_device *pdev) ++{ ++ struct fb_info *info; ++ int ret = -ENOMEM; ++ struct rpisense_fb *rpisense_fb; ++ ++ rpisense = rpisense_get_dev(); ++ rpisense_fb = &rpisense->framebuffer; ++ ++ rpisense_fb_param.vmem = vzalloc(rpisense_fb_param.vmemsize); ++ if (!rpisense_fb_param.vmem) ++ return ret; ++ ++ rpisense_fb_param.vmem_work = devm_kmalloc(&pdev->dev, 193, GFP_KERNEL); ++ if (!rpisense_fb_param.vmem_work) ++ goto err_malloc; ++ ++ info = framebuffer_alloc(0, &pdev->dev); ++ if (!info) { ++ dev_err(&pdev->dev, "Could not allocate framebuffer.\n"); ++ goto err_malloc; ++ } ++ rpisense_fb->info = info; ++ ++ rpisense_fb_fix.smem_start = (unsigned long)rpisense_fb_param.vmem; ++ rpisense_fb_fix.smem_len = rpisense_fb_param.vmemsize; ++ ++ info->fbops = &rpisense_fb_ops; ++ info->fix = rpisense_fb_fix; ++ info->var = rpisense_fb_var; ++ info->fbdefio = &rpisense_fb_defio; ++ info->flags = FBINFO_FLAG_DEFAULT | FBINFO_VIRTFB; ++ info->screen_base = rpisense_fb_param.vmem; ++ info->screen_size = rpisense_fb_param.vmemsize; ++ ++ if (lowlight) ++ rpisense_fb_param.gamma = gamma_low; ++ ++ fb_deferred_io_init(info); ++ ++ ret = register_framebuffer(info); ++ if (ret < 0) { ++ dev_err(&pdev->dev, "Could not register framebuffer.\n"); ++ goto err_fballoc; ++ } ++ ++ fb_info(info, "%s frame buffer device\n", info->fix.id); ++ schedule_delayed_work(&info->deferred_work, rpisense_fb_defio.delay); ++ return 0; ++err_fballoc: ++ framebuffer_release(info); ++err_malloc: ++ vfree(rpisense_fb_param.vmem); ++ return ret; ++} ++ ++static int rpisense_fb_remove(struct platform_device *pdev) ++{ ++ struct rpisense_fb *rpisense_fb = &rpisense->framebuffer; ++ struct fb_info *info = rpisense_fb->info; ++ ++ if (info) { ++ unregister_framebuffer(info); ++ fb_deferred_io_cleanup(info); ++ framebuffer_release(info); ++ vfree(rpisense_fb_param.vmem); ++ } ++ ++ return 0; ++} ++ ++#ifdef CONFIG_OF ++static const struct of_device_id rpisense_fb_id[] = { ++ { .compatible = "rpi,rpi-sense-fb" }, ++ { }, ++}; ++MODULE_DEVICE_TABLE(of, rpisense_fb_id); ++#endif ++ ++static struct platform_device_id rpisense_fb_device_id[] = { ++ { .name = "rpi-sense-fb" }, ++ { }, ++}; ++MODULE_DEVICE_TABLE(platform, rpisense_fb_device_id); ++ ++static struct platform_driver rpisense_fb_driver = { ++ .probe = rpisense_fb_probe, ++ .remove = rpisense_fb_remove, ++ .driver = { ++ .name = "rpi-sense-fb", ++ .owner = THIS_MODULE, ++ }, ++}; ++ ++module_platform_driver(rpisense_fb_driver); ++ ++MODULE_DESCRIPTION("Raspberry Pi Sense HAT framebuffer driver"); ++MODULE_AUTHOR("Serge Schneider "); ++MODULE_LICENSE("GPL"); ++ +--- /dev/null ++++ b/include/linux/mfd/rpisense/core.h +@@ -0,0 +1,47 @@ ++/* ++ * Raspberry Pi Sense HAT core driver ++ * http://raspberrypi.org ++ * ++ * Copyright (C) 2015 Raspberry Pi ++ * ++ * Author: Serge Schneider ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License as published by the ++ * Free Software Foundation; either version 2 of the License, or (at your ++ * option) any later version. ++ * ++ */ ++ ++#ifndef __LINUX_MFD_RPISENSE_CORE_H_ ++#define __LINUX_MFD_RPISENSE_CORE_H_ ++ ++#include ++#include ++ ++/* ++ * Register values. ++ */ ++#define RPISENSE_FB 0x00 ++#define RPISENSE_WAI 0xF0 ++#define RPISENSE_VER 0xF1 ++#define RPISENSE_KEYS 0xF2 ++#define RPISENSE_EE_WP 0xF3 ++ ++#define RPISENSE_ID 's' ++ ++struct rpisense { ++ struct device *dev; ++ struct i2c_client *i2c_client; ++ ++ /* Client devices */ ++ struct rpisense_js joystick; ++ struct rpisense_fb framebuffer; ++}; ++ ++struct rpisense *rpisense_get_dev(void); ++s32 rpisense_reg_read(struct rpisense *rpisense, int reg); ++int rpisense_reg_write(struct rpisense *rpisense, int reg, u16 val); ++int rpisense_block_write(struct rpisense *rpisense, const char *buf, int count); ++ ++#endif +--- /dev/null ++++ b/include/linux/mfd/rpisense/framebuffer.h +@@ -0,0 +1,32 @@ ++/* ++ * Raspberry Pi Sense HAT framebuffer driver ++ * http://raspberrypi.org ++ * ++ * Copyright (C) 2015 Raspberry Pi ++ * ++ * Author: Serge Schneider ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License as published by the ++ * Free Software Foundation; either version 2 of the License, or (at your ++ * option) any later version. ++ * ++ */ ++ ++#ifndef __LINUX_RPISENSE_FB_H_ ++#define __LINUX_RPISENSE_FB_H_ ++ ++#define SENSEFB_FBIO_IOC_MAGIC 0xF1 ++ ++#define SENSEFB_FBIOGET_GAMMA _IO(SENSEFB_FBIO_IOC_MAGIC, 0) ++#define SENSEFB_FBIOSET_GAMMA _IO(SENSEFB_FBIO_IOC_MAGIC, 1) ++#define SENSEFB_FBIORESET_GAMMA _IO(SENSEFB_FBIO_IOC_MAGIC, 2) ++ ++struct rpisense; ++ ++struct rpisense_fb { ++ struct platform_device *pdev; ++ struct fb_info *info; ++}; ++ ++#endif +--- /dev/null ++++ b/include/linux/mfd/rpisense/joystick.h +@@ -0,0 +1,35 @@ ++/* ++ * Raspberry Pi Sense HAT joystick driver ++ * http://raspberrypi.org ++ * ++ * Copyright (C) 2015 Raspberry Pi ++ * ++ * Author: Serge Schneider ++ * ++ * This program is free software; you can redistribute it and/or modify it ++ * under the terms of the GNU General Public License as published by the ++ * Free Software Foundation; either version 2 of the License, or (at your ++ * option) any later version. ++ * ++ */ ++ ++#ifndef __LINUX_RPISENSE_JOYSTICK_H_ ++#define __LINUX_RPISENSE_JOYSTICK_H_ ++ ++#include ++#include ++#include ++#include ++ ++struct rpisense; ++ ++struct rpisense_js { ++ struct platform_device *pdev; ++ struct input_dev *keys_dev; ++ struct gpio_desc *keys_desc; ++ struct work_struct keys_work_s; ++ int keys_irq; ++}; ++ ++ ++#endif diff --git a/target/linux/bcm27xx/patches-5.10/950-0060-Add-support-for-all-the-downstream-rpi-sound-card-dr.patch b/target/linux/bcm27xx/patches-5.10/950-0060-Add-support-for-all-the-downstream-rpi-sound-card-dr.patch new file mode 100644 index 0000000000..75b0d7a1a0 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0060-Add-support-for-all-the-downstream-rpi-sound-card-dr.patch @@ -0,0 +1,15106 @@ +From 6e520cdc4c898f0d02bbe40e2c466f9694933d9c Mon Sep 17 00:00:00 2001 +From: Florian Meier +Date: Mon, 25 Jan 2016 15:48:59 +0000 +Subject: [PATCH] Add support for all the downstream rpi sound card + drivers +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +ASoC: Add support for Rpi-DAC + +ASoC: Add prompt for ICS43432 codec + +Without a prompt string, a config setting can't be included in a +defconfig. Give CONFIG_SND_SOC_ICS43432 a prompt so that Pi soundcards +can use the driver. + +Signed-off-by: Phil Elwell + +Add IQaudIO Sound Card support for Raspberry Pi + +Set a limit of 0dB on Digital Volume Control + +The main volume control in the PCM512x DAC has a range up to ++24dB. This is dangerously loud and can potentially cause massive +clipping in the output stages. Therefore this sets a sensible +limit of 0dB for this control. + +Allow up to 24dB digital gain to be applied when using IQAudIO DAC+ + +24db_digital_gain DT param can be used to specify that PCM512x +codec "Digital" volume control should not be limited to 0dB gain, +and if specified will allow the full 24dB gain. + +Modify IQAudIO DAC+ ASoC driver to set card/dai config from dt + +Add the ability to set the card name, dai name and dai stream name, from +dt config. + +Signed-off-by: DigitalDreamtime + +IQaudIO: auto-mute for AMP+ and DigiAMP+ + +IQAudIO amplifier mute via GPIO22. Add dt params for "one-shot" unmute +and auto mute. + +Revision 2, auto mute implementing HiassofT suggestion to mute/unmute +using set_bias_level, rather than startup/shutdown.... +"By default DAPM waits 5 seconds (pmdown_time) before shutting down +playback streams so a close/stop immediately followed by open/start +doesn't trigger an amp mute+unmute." + +Tested on both AMP+ (via DAC+) and DigiAMP+, with both options... + +dtoverlay=iqaudio-dacplus,unmute_amp + "one-shot" unmute when kernel module loads. + +dtoverlay=iqaudio-dacplus,auto_mute_amp + Unmute amp when ALSA device opened by a client. Mute, with 5 second delay + when ALSA device closed. (Re-opening the device within the 5 second close + window, will cancel mute.) + +Revision 4, using gpiod. + +Revision 5, clean-up formatting before adding mute code. + - Convert tab plus 4 space formatting to 2x tab + - Remove '// NOT USED' commented code + +Revision 6, don't attempt to "one-shot" unmute amp, unless card is +successfully registered. + +Signed-off-by: DigitalDreamtime + +ASoC: iqaudio-dac: fix S24_LE format + +Remove set_bclk_ratio call so 24-bit data is transmitted in +24 bclk cycles. + +Signed-off-by: Matthias Reichl + +ASoC: iqaudio-dac: use modern dai_link style + +Signed-off-by: Matthias Reichl + +Added support for HiFiBerry DAC+ + +The driver is based on the HiFiBerry DAC driver. However HiFiBerry DAC+ uses +a different codec chip (PCM5122), therefore a new driver is necessary. + +Add support for the HiFiBerry DAC+ Pro. + +The HiFiBerry DAC+ and DAC+ Pro products both use the existing bcm sound driver with the DAC+ Pro having a special clock device driver representing the two high precision oscillators. + +An addition bug fix is included for the PCM512x codec where by the physical size of the sample frame is used in the calculation of the LRCK divisor as it was found to be wrong when using 24-bit depth sample contained in a little endian 4-byte sample frame. + +Limit PCM512x "Digital" gain to 0dB by default with HiFiBerry DAC+ + +24db_digital_gain DT param can be used to specify that PCM512x +codec "Digital" volume control should not be limited to 0dB gain, +and if specified will allow the full 24dB gain. + +Add dt param to force HiFiBerry DAC+ Pro into slave mode + +"dtoverlay=hifiberry-dacplus,slave" + +Add 'slave' param to use HiFiBerry DAC+ Pro in slave mode, +with Pi as master for bit and frame clock. + +Signed-off-by: DigitalDreamtime + +Fixed a bug when using 352.8kHz sample rate + +Signed-off-by: Daniel Matuschek + +ASoC: pcm512x: revert downstream changes + +This partially reverts commit 185ea05465aac8bf02a0d2b2f4289d42c72870b7 +which was added by https://github.com/raspberrypi/linux/pull/1152 + +The downstream pcm512x changes caused a regression, it broke normal +use of the 24bit format with the codec, eg when using simple-audio-card. + +The actual bug with 24bit playback is the incorrect usage +of physical_width in various drivers in the downstream tree +which causes 24bit data to be transmitted with 32 clock +cycles. So it's not the pcm512x that needs fixing, it's the +soundcard drivers. + +Signed-off-by: Matthias Reichl + +ASoC: hifiberry_dacplus: fix S24_LE format + +Remove set_bclk_ratio call so 24-bit data is transmitted in +24 bclk cycles. + +Signed-off-by: Matthias Reichl + +ASoC: hifiberry_dacplus: transmit S24_LE with 64 BCLK cycles + +Signed-off-by: Matthias Reichl + +hifiberry_dacplus: switch to snd_soc_dai_set_bclk_ratio + +Signed-off-by: Matthias Reichl + +ASoC: hifiberry_dacplus: use modern dai_link style + +Signed-off-by: Hui Wang + +Add driver for rpi-proto + +Forward port of 3.10.x driver from https://github.com/koalo +We are using a custom board and would like to use rpi 3.18.x +kernel. Patch works fine for our embedded system. + +URL to the audio chip: +http://www.mikroe.com/add-on-boards/audio-voice/audio-codec-proto/ + +Playback tested with devicetree enabled. + +Signed-off-by: Waldemar Brodkorb + +ASoC: rpi-proto: use modern dai_link style + +Signed-off-by: Hui Wang + +Add Support for JustBoom Audio boards + +justboom-dac: Adjust for ALSA API change + +As of 4.4, snd_soc_limit_volume now takes a struct snd_soc_card * +rather than a struct snd_soc_codec *. + +Signed-off-by: Phil Elwell + +ASoC: justboom-dac: fix S24_LE format + +Remove set_bclk_ratio call so 24-bit data is transmitted in +24 bclk cycles. + +Also remove hw_params as it's no longer needed. + +Signed-off-by: Matthias Reichl + +ASoC: justboom-dac: use modern dai_link style + +Signed-off-by: Matthias Reichl + +New AudioInjector.net Pi soundcard with low jitter audio in and out. + +Contains the sound/soc/bcm ALSA machine driver and necessary alterations to the Kconfig and Makefile. +Adds the dts overlay and updates the Makefile and README. +Updates the relevant defconfig files to enable building for the Raspberry Pi. +Thanks to Phil Elwell (pelwell) for the review, simple-card concepts and discussion. Thanks to Clive Messer for overlay naming suggestions. + +Added support for headphones, microphone and bclk_ratio settings. + +This patch adds headphone and microphone capability to the Audio Injector sound card. The patch also sets the bit clock ratio for use in the bcm2835-i2s driver. The bcm2835-i2s can't handle an 8 kHz sample rate when the bit clock is at 12 MHz because its register is only 10 bits wide which can't represent the ch2 offset of 1508. For that reason, the rate constraint is added. + +ASoC: audioinjector-pi-soundcard: use modern dai_link style + +Signed-off-by: Hui Wang + +New driver for RRA DigiDAC1 soundcard using WM8741 + WM8804 + +ASoC: digidac1-soundcard: use modern dai_link style + +Signed-off-by: Hui Wang + +Add support for Dion Audio LOCO DAC-AMP HAT + +Using dedicated machine driver and pcm5102a codec driver. + +Signed-off-by: DigitalDreamtime + +ASoC: dionaudio_loco: use modern dai_link style + +Signed-off-by: Hui Wang + +Allo Piano DAC boards: Initial 2 channel (stereo) support (#1645) + +Add initial 2 channel (stereo) support for Allo Piano DAC (2.0/2.1) boards, +using allo-piano-dac-pcm512x-audio overlay and allo-piano-dac ALSA ASoC +machine driver. + +NB. The initial support is 2 channel (stereo) ONLY! +(The Piano DAC 2.1 will only support 2 channel (stereo) left/right output, + pending an update to the upstream pcm512x codec driver, which will have + to be submitted via upstream. With the initial downstream support, + provided by this patch, the Piano DAC 2.1 subwoofer outputs will + not function.) + +Signed-off-by: Baswaraj K +Signed-off-by: Clive Messer +Tested-by: Clive Messer + +ASoC: allo-piano-dac: fix S24_LE format + +Remove set_bclk_ratio call so 24-bit data is transmitted in +24 bclk cycles. + +Also remove hw_params and ops as they are no longer needed. + +Signed-off-by: Matthias Reichl + +ASoC: allo-piano-dac: use modern dai_link style + +Signed-off-by: Hui Wang + +Add support for Allo Piano DAC 2.1 plus add-on board for Raspberry Pi. + +The Piano DAC 2.1 has support for 4 channels with subwoofer. + +Signed-off-by: Baswaraj K +Reviewed-by: Vijay Kumar B. +Reviewed-by: Raashid Muhammed + +Add clock changes and mute gpios (#1938) + +Also improve code style and adhere to ALSA coding conventions. + +Signed-off-by: Baswaraj K +Reviewed-by: Vijay Kumar B. +Reviewed-by: Raashid Muhammed + +PianoPlus: Dual Mono & Dual Stereo features added (#2069) + +allo-piano-dac-plus: Master volume added + fixes + +Master volume added, which controls both DACs volumes. + +See: https://github.com/raspberrypi/linux/pull/2149 + +Also fix initial max volume, default mode value, and unmute. + +Signed-off-by: allocom + +ASoC: allo-piano-dac-plus: fix S24_LE format + +Remove set_bclk_ratio call so 24-bit data is transmitted in +24 bclk cycles. + +Signed-off-by: Matthias Reichl + +sound: bcm: Fix memset dereference warning + +This warning appears with GCC 6.4.0 from toolchains.bootlin.com: + +../sound/soc/bcm/allo-piano-dac-plus.c: In function ‘snd_allo_piano_dac_init’: +../sound/soc/bcm/allo-piano-dac-plus.c:711:30: warning: argument to ‘sizeof’ in ‘memset’ call is the same expression as the destination; did you mean to dereference it? [-Wsizeof-pointer-memaccess] + memset(glb_ptr, 0x00, sizeof(glb_ptr)); + ^ + +Suggested-by: Phil Elwell +Signed-off-by: Nathan Chancellor + +ASoC: allo-piano-dac-plus: use modern dai_link style + +Signed-off-by: Hui Wang + +Add support for Allo Boss DAC add-on board for Raspberry Pi. (#1924) + +Signed-off-by: Baswaraj K +Reviewed-by: Deepak +Reviewed-by: BabuSubashChandar + +Add support for new clock rate and mute gpios. + +Signed-off-by: Baswaraj K +Reviewed-by: Deepak +Reviewed-by: BabuSubashChandar + +ASoC: allo-boss-dac: fix S24_LE format + +Remove set_bclk_ratio call so 24-bit data is transmitted in +24 bclk cycles. + +Signed-off-by: Matthias Reichl + +ASoC: allo-boss-dac: transmit S24_LE with 64 BCLK cycles + +Signed-off-by: Matthias Reichl + +allo-boss-dac: switch to snd_soc_dai_set_bclk_ratio + +Signed-off-by: Matthias Reichl + +ASoC: allo-boss-dac: use modern dai_link style + +Signed-off-by: Hui Wang + +Support for Blokas Labs pisound board + +Pisound dynamic overlay (#1760) + +Restructuring pisound-overlay.dts, so it can be loaded and unloaded dynamically using dtoverlay. + +Print a logline when the kernel module is removed. + +pisound improvements: + +* Added a writable sysfs object to enable scripts / user space software +to blink MIDI activity LEDs for variable duration. +* Improved hw_param constraints setting. +* Added compatibility with S16_LE sample format. +* Exposed some simple placeholder volume controls, so the card appears +in volumealsa widget. + +Add missing SND_PISOUND selects dependency to SND_RAWMIDI + +Without it the Pisound module fails to compile. +See https://github.com/raspberrypi/linux/issues/2366 + +Updates for Pisound module code: + + * Merged 'Fix a warning in DEBUG builds' (1c8b82b). + * Updating some strings and copyright information. + * Fix for handling high load of MIDI input and output. + * Use dual rate oversampling ratio for 96kHz instead of single + rate one. + +Signed-off-by: Giedrius Trainavicius + +Fixing memset call in pisound.c + +Signed-off-by: Giedrius Trainavicius + +Fix for Pisound's MIDI Input getting blocked for a while in rare cases. + +There was a possible race condition which could lead to Input's FIFO queue +to be underflown, causing high amount of processing in the worker thread for +some period of time. + +Signed-off-by: Giedrius Trainavicius + +Fix for Pisound kernel module in Real Time kernel configuration. + +When handler of data_available interrupt is fired, queue_work ends up +getting called and it can block on a spin lock which is not allowed in +interrupt context. The fix was to run the handler from a thread context +instead. + +Pisound: Remove spinlock usage around spi_sync + +ASoC: pisound: use modern dai_link style + +Signed-off-by: Hui Wang + +ASoC: pisound: fix the parameter for spi_device_match + +Signed-off-by: Hui Wang + +ASoC: Add driver for Cirrus Logic Audio Card + +Note: due to problems with deferred probing of regulators +the following softdep should be added to a modprobe.d file + +softdep arizona-spi pre: arizona-ldo1 + +Signed-off-by: Matthias Reichl + +ASoC: rpi-cirrus: use modern dai_link style + +Signed-off-by: Matthias Reichl + +sound: Support for Dion Audio LOCO-V2 DAC-AMP HAT + +Signed-off-by: Miquel Blauw + +ASoC: dionaudio_loco-v2: fix S24_LE format + +Remove set_bclk_ratio call so 24-bit data is transmitted in +24 bclk cycles. + +Also remove hw_params and ops as they are no longer needed. + +Signed-off-by: Matthias Reichl + +ASoC: dionaudio_loco-v2: use modern dai_link style + +Signed-off-by: Hui Wang + +Add support for Fe-Pi audio sound card. (#1867) + +Fe-Pi Audio Sound Card is based on NXP SGTL5000 codec. +Mechanical specification of the board is the same the Raspberry Pi Zero. +3.5mm jacks for Headphone/Mic, Line In, and Line Out. + +Signed-off-by: Henry Kupis + +ASoC: fe-pi-audio: use modern dai_link style + +Signed-off-by: Hui Wang + +Add support for the AudioInjector.net Octo sound card + +AudioInjector Octo: sample rates, regulators, reset + +This patch adds new sample rates to the Audioinjector Octo sound card. The +new supported rates are (in kHz) : +96, 48, 32, 24, 16, 8, 88.2, 44.1, 29.4, 22.05, 14.7 + +Reference the bcm270x DT regulators in the overlay. + +This patch adds a reset GPIO for the AudioInjector.net octo sound card. + +Audioinjector octo : Make the playback and capture symmetric + +This patch ensures that the sample rate and channel count of the audioinjector +octo sound card are symmetric. + +audioinjector-octo: Add continuous clock feature + +By user request, add a switch to prevent the clocks being stopped when +the stream is paused, stopped or shutdown. Provide access to the switch +by adding a 'non-stop-clocks' parameter to the audioinjector-addons +overlay. + +See: https://github.com/raspberrypi/linux/issues/2409 + +Signed-off-by: Phil Elwell + +sound: Fixes for audioinjector-octo under 4.19 + +1. Move the DT alias declaration to the I2C shim in the cases +where the shim is enabled. This works around a problem caused by a +4.19 commit [1] that generates DT/OF uevents for I2C drivers. + +2. Fix the diagnostics in an error path of the soundcard driver to +correctly identify the reason for the failure to load. + +3. Move the declaration of the clock node in the overlay outside +the I2C node to avoid warnings. + +4. Sort the overlay nodes so that dependencies are only to earlier +fragments, in an attempt to get runtime dtoverlay application to +work (it still doesn't...) + +See: https://github.com/Audio-Injector/Octo/issues/14 +Signed-off-by: Phil Elwell + +[1] af503716ac14 ("i2c: core: report OF style module alias for devices registered via OF") + +ASoC: audioinjector-octo-soundcard: use modern dai_link style + +Signed-off-by: Hui Wang + +Driver support for Google voiceHAT soundcard. + +ASoC: googlevoicehat-codec: Use correct device when grabbing GPIO + +The fixup for the VoiceHAT in 4.18 incorrectly tried to find the +sdmode GPIO pin under the card device, not the codec device. +This failed, and therefore caused the device probe to fail. + +Signed-off-by: Dave Stevenson + +ASoC: googlevoicehat-codec: Reformat for kernel coding standards + +Fix all whitespace, indentation, and bracing errors. + +Signed-off-by: Dave Stevenson + +ASoC: googlevoicehat-codec: Make driver function structure const + +Make voicehat_component_driver a const structure. + +Signed-off-by: Dave Stevenson + +ASoC: googlevoicehat-codec: Only convert from ms to jiffies once + +Minor optimisation and allows to become checkpatch clean. +A msec value is read out of DT or from a define, and convert once to +jiffies, rather than every time that it is used. + +Signed-off-by: Dave Stevenson + +Driver and overlay for Allo Katana DAC + +Allo Katana DAC: Updated default values + +Signed-off-by: Jaikumar + +Added mute stream func + +Signed-off-by: Jaikumar + +codecs: Correct Katana minimum volume + +Update Katana minimum volume to get the exact 0.5 dB value in each step. + +Signed-off-by: Sudeep Kumar + +ASoC: Add generic RPI driver for simple soundcards. + +The RPI simple sound card driver provides a generic ALSA SOC card driver +supporting a variety of Pi HAT soundcards. The intention is to avoid +the duplication of code for cards that can't be fully supported by +the soc simple/graph cards but are otherwise almost identical. + +This initial commit adds support for the ADAU1977 ADC, Google VoiceHat, +HifiBerry AMP, HifiBerry DAC and RPI DAC. + +Signed-off-by: Tim Gover + +ASoC: Use correct card name in rpi-simple driver + +Use the specific card name from drvdata instead of the snd_rpi_simple + +rpi-simple-soundcard: Use nicer driver name "RPi-simple" + +Rename the driver from "RPI simple soundcard" to "RPi-simple" so that +the driver name won't be mangled allowing to be used unaltered as the +card conf filename. + +ASoC: rpi-simple-soundcard: use modern dai_link style + +Signed-off-by: Hui Wang + +ASoC: Add Kconfig and Makefile for sound/soc/bcm + +Signed-off-by: popcornmix + +ASoC: Create a generic Pi Hat WM8804 driver + +Reduce the amount of duplicated code by creating a generic driver for +Pi Hat digi cards using the WM8804 codec. + +This replaces the +Allo DigiOne, Hifiberry Digi/Pro, JustBoom Digi and IQAudIO Digi +dedicate soundcard drivers with a generic driver. + +There are no significant changes to the runtime behavior of the drivers +and end users should not have to change any configuration settings +after upgrading. + +Minor changes +* Check the return value of snd_soc_component_update_bits +* Added some pr_debug tracing +* Various checkpatch tidyups +* Updated allodigi-one to use use 128FS at > 96 Khz. This appears to + be an omission in the original driver code so followed the Hifiberry + DAC driver approach. + +ASoC: rpi-wm8804-soundcard: use modern dai_link style + +Signed-off-by: Matthias Reichl + +rpi-wm8804-soundcard: drop PWRDN register writes + +Since kernel 4.0 the PWRDN register bits are under DAPM +control from the wm8804 driver. + +Drop code that modifies that register to avoid interfering +with DAPM. + +Signed-off-by: Matthias Reichl + +rpi-wm8804-soundcard: configure wm8804 clocks only on rate change + +This should avoid clicks when stopping and immediately afterwards +starting a stream with the same samplerate as before. + +Signed-off-by: Matthias Reichl + +rpi-wm8804-soundcard: Fixed MCLKDIV for Allo Digione + +The Allo Digione board wants a fixed MCLKDIV of 256. + +See: https://github.com/raspberrypi/linux/issues/3296 + +Signed-off-by: Phil Elwell + +ASoC: Add support for AudioSense-Pi add-on soundcard + +AudioSense-Pi is a RPi HAT based on a TI's TLV320AIC32x4 stereo codec + +This hardware provides multiple audio I/O capabilities to the RPi. +The codec connects to the RPi's SoC through the I2S Bus. + +The following devices can be connected through a 3.5mm jack + 1. Line-In: Plain old audio in from mobile phones, PCs, etc., + 2. Mic-In: Connect a microphone + 3. Line-Out: Connect the output to a speaker + 4. Headphones: Connect a Headphone w or w/o microphones + +Multiple Inputs: + It supports the following combinations + 1. Two stereo Line-Inputs and a microphone + 2. One stereo Line-Input and two microphones + 3. Two stereo Line-Inputs, a microphone and + one mono line-input (with h/w hack) + 4. One stereo Line-Input, two microphones and + one mono line-input (with h/w hack) + +Multiple Outputs: + Audio output can be routed to the headphones or + speakers (with additional hardware) + +Signed-off-by: b-ak + +ASoC: audiosense-pi: use modern dai_link style + +Signed-off-by: Hui Wang + +Added driver for the HiFiBerry DAC+ ADC (#2694) + +Signed-off-by: Daniel Matuschek + +hifiberry_dacplusadc: switch to snd_soc_dai_set_bclk_ratio + +Signed-off-by: Matthias Reichl + +ASoC: hifiberry_dacplusadc: fix DAI link setup + +The driver only defines a single DAI link and the code that tries +to setup the second (non-existent) DAI link looks wrong - using dmic +as a CPU/platform driver doesn't make any sense. + +The DT overlay doesn't define a dmic property, so the code was never +executed (otherwise it would have resulted in a memory corruption). + +So drop the offending code to prevent issues if a dmic property +should be added to the DT overlay. + +Signed-off-by: Matthias Reichl + +ASoC: hifiberry_dacplusadc: use modern dai_link style + +Signed-off-by: Matthias Reichl + +Audiophonics I-Sabre 9038Q2M DAC driver + +Signed-off-by: Audiophonics + +ASoC: i-sabre-q2m: use modern dai_link style + +Signed-off-by: Hui Wang + +Added IQaudIO Pi-Codec board support (#2969) + +Add support for the IQaudIO Pi-Codec board. + +Signed-off-by: Gordon + +Fixed 48k timing issue + +ASoC: iqaudio-codec: use modern dai_link style + +Signed-off-by: Hui Wang + +adds the Hifiberry DAC+ADC PRO version + +This adds the driver for the DAC+ADC PRO version of the Hifiberry soundcard with software controlled PCM1863 ADC +Signed-off-by: Joerg Schambacher joerg@i2audio.com + +Add Hifiberry DAC+DSP soundcard driver (#3224) + +Adds the driver for the Hifiberry DAC+DSP. It supports capture and +playback depending on the DSP firmware. + +Signed-off-by: Joerg Schambacher + +Allow simultaneous use of JustBoom DAC and Digi + +Signed-off-by: Johannes Krude + +Pisound: MIDI communication fixes for scaled down CPU. + +* Increased maximum SPI communication speed to avoid running too slow + when the CPU is scaled down and losing MIDI data. + +* Keep track of buffer usage in millibytes for higher precision. + +Signed-off-by: Giedrius Trainavičius + +sound: Add the HiFiBerry DAC+HD version + +This adds the driver for the DAC+HD version supporting HiFiBerry's +PCM179x based DACs. It also adds PLL control for clock generation. + +Signed-off-by: Joerg Schambacher + +Fix master mode settings of HiFiBerry DAC+ADC PRO card (#3424) + +This patch fixes the board DAI setting when in master-mode. +Wrong setting could have caused random pop noise. + +Signed-off-by: Joerg Schambacher + +adds LED OFF feature to HiFiBerry DAC+ADC PRO sound card + +This adds a DT overlay parameter 'leds_off' which allows +to switch off the onboard activity LEDs at all times +which has been requested by some users. + +Signed-off-by: Joerg Schambacher + +adds LED OFF feature to HiFiBerry DAC+ADC sound card + +This adds a DT overlay parameter 'leds_off' which allows +to switch off the onboard activity LEDs at all times +which has been requested by some users. + +Signed-off-by: Joerg Schambacher + +adds LED OFF feature to HiFiBerry DAC+/DAC+PRO sound cards + +This adds a DT overlay parameter 'leds_off' which allows +to switch off the onboard activity LEDs at all times +which has been requested by some users. + +Signed-off-by: Joerg Schambacher + +pisound: Added reading Pisound board hardware revision and exposing it (#3425) + +pisound: Added reading Pisound board hardware revision and exposing it in kernel log and sysfs file: + +/sys/kernel/pisound/hw_version + +Signed-off-by: Giedrius + +Added driver for HiFiBerry Amp amplifier add-on board + +The driver contains a low-level hardware driver for the TAS5713 and the +drivers for the Raspberry Pi I2S subsystem. + +TAS5713: return error if initialisation fails + +Existing TAS5713 driver logs errors during initialisation, but does not return +an error code. Therefore even if initialisation fails, the driver will still be +loaded, but won't work. This patch fixes this. I2C communication error will now +reported correctly by a non-zero return code. + +HiFiBerry Amp: fix device-tree problems + +Some code to load the driver based on device-tree-overlays was missing. This is added by this patch. + +According to 5713 pdf doc CLOCK_CTRL is a readonly status register, and it behaves so. Remove useless setting + +sound: pcm512x-codec: Adding 352.8kHz samplerate support + +sound/soc: only first codec is master in multicodec setup + +When using multiple codecs, at most one codec should generate the master +clock. All codecs except the first are therefore configured for slave +mode. + +Signed-off-by: Johannes Krude + +ASoC: Fix snd_soc_get_pcm_runtime usage + +Commit [1] changed the snd_soc_get_pcm_runtime to take a dai_link +pointer instead of a string. Patch up the downstream drivers to use +the modified API. + +Signed-off-by: Phil Elwell + +[1] 4468189ff307 ("ASoC: soc-core: find rtd via dai_link pointer at snd_soc_get_pcm_runtime()") + +Add support for the AudioInjector.net Isolated sound card + +This patch adds support for the Audio Injector Isolated sound card. + +Signed-off-by: Matt Flax + +Add support for merus-amp soundcard and ma120x0p codec + +Add 96KHz rate support to MA120X0P codec and make enable and mute gpio +pins optional. + +Signed-off-by: AMuszkat + +Fixes a problem with clock settings of HiFiBerry DAC+ADC PRO (#3545) + +This patch fixes a problem of the re-calculation of +i2s-clock and -parameter settings when only the ADC is activated. + +Signed-off-by: Joerg Schambacher + +configs: Enable the AD193x codecs + +See: https://github.com/raspberrypi/linux/issues/2850 + +Signed-off-by: Phil Elwell + +Switch to snd_soc_dai_set_bclk_ratio +Replaces obsolete function snd_soc_dai_set_tdm_slot + +Signed-off-by: Joerg Schambacher + +Enhances the DAC+ driver to control the optional headphone amplifier + +Probes on the I2C bus for TPA6130A2, if successful, it sets DT-parameter +'status' from 'disabled' to 'okay' using change_sets to enable +the headphone control. + +Signed-off-by: Joerg Schambacher joerg@i2audio.com +--- + .../devicetree/bindings/vendor-prefixes.txt | 463 ++++++ + .../devicetree/bindings/vendor-prefixes.yaml | 2 + + drivers/clk/Kconfig | 6 + + drivers/clk/Makefile | 3 + + drivers/clk/clk-allo-dac.c | 161 ++ + drivers/clk/clk-hifiberry-dachd.c | 333 ++++ + drivers/clk/clk-hifiberry-dacpro.c | 160 ++ + sound/soc/bcm/Kconfig | 274 ++++ + sound/soc/bcm/Makefile | 63 +- + sound/soc/bcm/allo-boss-dac.c | 456 ++++++ + sound/soc/bcm/allo-katana-codec.c | 388 +++++ + sound/soc/bcm/allo-piano-dac-plus.c | 987 ++++++++++++ + sound/soc/bcm/allo-piano-dac.c | 122 ++ + .../bcm/audioinjector-isolated-soundcard.c | 183 +++ + sound/soc/bcm/audioinjector-octo-soundcard.c | 346 +++++ + sound/soc/bcm/audioinjector-pi-soundcard.c | 187 +++ + sound/soc/bcm/audiosense-pi.c | 248 +++ + sound/soc/bcm/digidac1-soundcard.c | 421 +++++ + sound/soc/bcm/dionaudio_loco-v2.c | 117 ++ + sound/soc/bcm/dionaudio_loco.c | 117 ++ + sound/soc/bcm/fe-pi-audio.c | 154 ++ + sound/soc/bcm/googlevoicehat-codec.c | 214 +++ + sound/soc/bcm/hifiberry_dacplus.c | 424 +++++ + sound/soc/bcm/hifiberry_dacplusadc.c | 398 +++++ + sound/soc/bcm/hifiberry_dacplusadcpro.c | 543 +++++++ + sound/soc/bcm/hifiberry_dacplusdsp.c | 90 ++ + sound/soc/bcm/hifiberry_dacplushd.c | 238 +++ + sound/soc/bcm/i-sabre-q2m.c | 158 ++ + sound/soc/bcm/iqaudio-codec.c | 274 ++++ + sound/soc/bcm/iqaudio-dac.c | 223 +++ + sound/soc/bcm/justboom-both.c | 266 ++++ + sound/soc/bcm/justboom-dac.c | 147 ++ + sound/soc/bcm/pisound.c | 1238 +++++++++++++++ + sound/soc/bcm/rpi-cirrus.c | 1025 ++++++++++++ + sound/soc/bcm/rpi-proto.c | 147 ++ + sound/soc/bcm/rpi-simple-soundcard.c | 339 ++++ + sound/soc/bcm/rpi-wm8804-soundcard.c | 410 +++++ + sound/soc/codecs/Kconfig | 28 +- + sound/soc/codecs/Makefile | 8 + + sound/soc/codecs/cs42xx8-i2c.c | 9 +- + sound/soc/codecs/cs42xx8.c | 2 + + sound/soc/codecs/i-sabre-codec.c | 392 +++++ + sound/soc/codecs/i-sabre-codec.h | 42 + + sound/soc/codecs/ma120x0p.c | 1384 +++++++++++++++++ + sound/soc/codecs/pcm1794a.c | 69 + + sound/soc/codecs/pcm512x.c | 2 +- + sound/soc/codecs/tas5713.c | 363 +++++ + sound/soc/codecs/tas5713.h | 210 +++ + sound/soc/soc-core.c | 10 +- + 49 files changed, 13837 insertions(+), 7 deletions(-) + create mode 100644 Documentation/devicetree/bindings/vendor-prefixes.txt + create mode 100644 drivers/clk/clk-allo-dac.c + create mode 100644 drivers/clk/clk-hifiberry-dachd.c + create mode 100644 drivers/clk/clk-hifiberry-dacpro.c + create mode 100644 sound/soc/bcm/allo-boss-dac.c + create mode 100644 sound/soc/bcm/allo-katana-codec.c + create mode 100644 sound/soc/bcm/allo-piano-dac-plus.c + create mode 100644 sound/soc/bcm/allo-piano-dac.c + create mode 100644 sound/soc/bcm/audioinjector-isolated-soundcard.c + create mode 100644 sound/soc/bcm/audioinjector-octo-soundcard.c + create mode 100644 sound/soc/bcm/audioinjector-pi-soundcard.c + create mode 100644 sound/soc/bcm/audiosense-pi.c + create mode 100644 sound/soc/bcm/digidac1-soundcard.c + create mode 100644 sound/soc/bcm/dionaudio_loco-v2.c + create mode 100644 sound/soc/bcm/dionaudio_loco.c + create mode 100644 sound/soc/bcm/fe-pi-audio.c + create mode 100644 sound/soc/bcm/googlevoicehat-codec.c + create mode 100644 sound/soc/bcm/hifiberry_dacplus.c + create mode 100644 sound/soc/bcm/hifiberry_dacplusadc.c + create mode 100644 sound/soc/bcm/hifiberry_dacplusadcpro.c + create mode 100644 sound/soc/bcm/hifiberry_dacplusdsp.c + create mode 100644 sound/soc/bcm/hifiberry_dacplushd.c + create mode 100644 sound/soc/bcm/i-sabre-q2m.c + create mode 100644 sound/soc/bcm/iqaudio-codec.c + create mode 100644 sound/soc/bcm/iqaudio-dac.c + create mode 100644 sound/soc/bcm/justboom-both.c + create mode 100644 sound/soc/bcm/justboom-dac.c + create mode 100644 sound/soc/bcm/pisound.c + create mode 100644 sound/soc/bcm/rpi-cirrus.c + create mode 100644 sound/soc/bcm/rpi-proto.c + create mode 100644 sound/soc/bcm/rpi-simple-soundcard.c + create mode 100644 sound/soc/bcm/rpi-wm8804-soundcard.c + create mode 100644 sound/soc/codecs/i-sabre-codec.c + create mode 100644 sound/soc/codecs/i-sabre-codec.h + create mode 100644 sound/soc/codecs/ma120x0p.c + create mode 100644 sound/soc/codecs/pcm1794a.c + create mode 100644 sound/soc/codecs/tas5713.c + create mode 100644 sound/soc/codecs/tas5713.h + +--- /dev/null ++++ b/Documentation/devicetree/bindings/vendor-prefixes.txt +@@ -0,0 +1,463 @@ ++Device tree binding vendor prefix registry. Keep list in alphabetical order. ++ ++This isn't an exhaustive list, but you should add new prefixes to it before ++using them to avoid name-space collisions. ++ ++abilis Abilis Systems ++abracon Abracon Corporation ++actions Actions Semiconductor Co., Ltd. ++active-semi Active-Semi International Inc ++ad Avionic Design GmbH ++adafruit Adafruit Industries, LLC ++adapteva Adapteva, Inc. ++adaptrum Adaptrum, Inc. ++adh AD Holdings Plc. ++adi Analog Devices, Inc. ++advantech Advantech Corporation ++aeroflexgaisler Aeroflex Gaisler AB ++al Annapurna Labs ++allo Allo.com ++allwinner Allwinner Technology Co., Ltd. ++alphascale AlphaScale Integrated Circuits Systems, Inc. ++altr Altera Corp. ++amarula Amarula Solutions ++amazon Amazon.com, Inc. ++amcc Applied Micro Circuits Corporation (APM, formally AMCC) ++amd Advanced Micro Devices (AMD), Inc. ++amediatech Shenzhen Amediatech Technology Co., Ltd ++amlogic Amlogic, Inc. ++ampire Ampire Co., Ltd. ++ams AMS AG ++amstaos AMS-Taos Inc. ++analogix Analogix Semiconductor, Inc. ++andestech Andes Technology Corporation ++apm Applied Micro Circuits Corporation (APM) ++aptina Aptina Imaging ++arasan Arasan Chip Systems ++archermind ArcherMind Technology (Nanjing) Co., Ltd. ++arctic Arctic Sand ++aries Aries Embedded GmbH ++arm ARM Ltd. ++armadeus ARMadeus Systems SARL ++arrow Arrow Electronics ++artesyn Artesyn Embedded Technologies Inc. ++asahi-kasei Asahi Kasei Corp. ++aspeed ASPEED Technology Inc. ++asus AsusTek Computer Inc. ++atlas Atlas Scientific LLC ++atmel Atmel Corporation ++auo AU Optronics Corporation ++auvidea Auvidea GmbH ++avago Avago Technologies ++avia avia semiconductor ++avic Shanghai AVIC Optoelectronics Co., Ltd. ++avnet Avnet, Inc. ++axentia Axentia Technologies AB ++axis Axis Communications AB ++bananapi BIPAI KEJI LIMITED ++bhf Beckhoff Automation GmbH & Co. KG ++bitmain Bitmain Technologies ++blokaslabs Vilniaus Blokas UAB ++boe BOE Technology Group Co., Ltd. ++bosch Bosch Sensortec GmbH ++boundary Boundary Devices Inc. ++brcm Broadcom Corporation ++buffalo Buffalo, Inc. ++bticino Bticino International ++calxeda Calxeda ++capella Capella Microsystems, Inc ++cascoda Cascoda, Ltd. ++catalyst Catalyst Semiconductor, Inc. ++cavium Cavium, Inc. ++cdns Cadence Design Systems Inc. ++cdtech CDTech(H.K.) Electronics Limited ++ceva Ceva, Inc. ++chipidea Chipidea, Inc ++chipone ChipOne ++chipspark ChipSPARK ++chrp Common Hardware Reference Platform ++chunghwa Chunghwa Picture Tubes Ltd. ++ciaa Computadora Industrial Abierta Argentina ++cirrus Cirrus Logic, Inc. ++cloudengines Cloud Engines, Inc. ++cnm Chips&Media, Inc. ++cnxt Conexant Systems, Inc. ++compulab CompuLab Ltd. ++cortina Cortina Systems, Inc. ++cosmic Cosmic Circuits ++crane Crane Connectivity Solutions ++creative Creative Technology Ltd ++crystalfontz Crystalfontz America, Inc. ++csky Hangzhou C-SKY Microsystems Co., Ltd ++cubietech Cubietech, Ltd. ++cypress Cypress Semiconductor Corporation ++cznic CZ.NIC, z.s.p.o. ++dallas Maxim Integrated Products (formerly Dallas Semiconductor) ++dataimage DataImage, Inc. ++davicom DAVICOM Semiconductor, Inc. ++delta Delta Electronics, Inc. ++denx Denx Software Engineering ++devantech Devantech, Ltd. ++dh DH electronics GmbH ++digi Digi International Inc. ++digilent Diglent, Inc. ++dioo Dioo Microcircuit Co., Ltd ++dlc DLC Display Co., Ltd. ++dlg Dialog Semiconductor ++dlink D-Link Corporation ++dmo Data Modul AG ++domintech Domintech Co., Ltd. ++dongwoon Dongwoon Anatech ++dptechnics DPTechnics ++dragino Dragino Technology Co., Limited ++ea Embedded Artists AB ++ebs-systart EBS-SYSTART GmbH ++ebv EBV Elektronik ++eckelmann Eckelmann AG ++edt Emerging Display Technologies ++eeti eGalax_eMPIA Technology Inc ++elan Elan Microelectronic Corp. ++elgin Elgin S/A. ++embest Shenzhen Embest Technology Co., Ltd. ++emlid Emlid, Ltd. ++emmicro EM Microelectronic ++emtrion emtrion GmbH ++endless Endless Mobile, Inc. ++energymicro Silicon Laboratories (formerly Energy Micro AS) ++engicam Engicam S.r.l. ++epcos EPCOS AG ++epfl Ecole Polytechnique Fédérale de Lausanne ++epson Seiko Epson Corp. ++est ESTeem Wireless Modems ++ettus NI Ettus Research ++eukrea Eukréa Electromatique ++everest Everest Semiconductor Co. Ltd. ++everspin Everspin Technologies, Inc. ++exar Exar Corporation ++excito Excito ++ezchip EZchip Semiconductor ++facebook Facebook ++fairphone Fairphone B.V. ++faraday Faraday Technology Corporation ++fastrax Fastrax Oy ++fcs Fairchild Semiconductor ++feiyang Shenzhen Fly Young Technology Co.,LTD. ++firefly Firefly ++focaltech FocalTech Systems Co.,Ltd ++friendlyarm Guangzhou FriendlyARM Computer Tech Co., Ltd ++fsl Freescale Semiconductor ++fujitsu Fujitsu Ltd. ++gateworks Gateworks Corporation ++gcw Game Consoles Worldwide ++ge General Electric Company ++geekbuying GeekBuying ++gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. ++GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. ++geniatech Geniatech, Inc. ++giantec Giantec Semiconductor, Inc. ++giantplus Giantplus Technology Co., Ltd. ++globalscale Globalscale Technologies, Inc. ++globaltop GlobalTop Technology, Inc. ++gmt Global Mixed-mode Technology, Inc. ++goodix Shenzhen Huiding Technology Co., Ltd. ++google Google, Inc. ++grinn Grinn ++grmn Garmin Limited ++gumstix Gumstix, Inc. ++gw Gateworks Corporation ++hannstar HannStar Display Corporation ++haoyu Haoyu Microelectronic Co. Ltd. ++hardkernel Hardkernel Co., Ltd ++hideep HiDeep Inc. ++himax Himax Technologies, Inc. ++hisilicon Hisilicon Limited. ++hit Hitachi Ltd. ++hitex Hitex Development Tools ++holt Holt Integrated Circuits, Inc. ++honeywell Honeywell ++hp Hewlett Packard ++holtek Holtek Semiconductor, Inc. ++hwacom HwaCom Systems Inc. ++i2se I2SE GmbH ++ibm International Business Machines (IBM) ++icplus IC Plus Corp. ++idt Integrated Device Technologies, Inc. ++ifi Ingenieurburo Fur Ic-Technologie (I/F/I) ++ilitek ILI Technology Corporation (ILITEK) ++img Imagination Technologies Ltd. ++infineon Infineon Technologies ++inforce Inforce Computing ++ingenic Ingenic Semiconductor ++innolux Innolux Corporation ++inside-secure INSIDE Secure ++intel Intel Corporation ++intercontrol Inter Control Group ++invensense InvenSense Inc. ++inversepath Inverse Path ++iom Iomega Corporation ++isee ISEE 2007 S.L. ++isil Intersil ++issi Integrated Silicon Solutions Inc. ++itead ITEAD Intelligent Systems Co.Ltd ++iwave iWave Systems Technologies Pvt. Ltd. ++jdi Japan Display Inc. ++jedec JEDEC Solid State Technology Association ++jianda Jiandangjing Technology Co., Ltd. ++karo Ka-Ro electronics GmbH ++keithkoep Keith & Koep GmbH ++keymile Keymile GmbH ++khadas Khadas ++kiebackpeter Kieback & Peter GmbH ++kinetic Kinetic Technologies ++kingdisplay King & Display Technology Co., Ltd. ++kingnovel Kingnovel Technology Co., Ltd. ++koe Kaohsiung Opto-Electronics Inc. ++kosagi Sutajio Ko-Usagi PTE Ltd. ++kyo Kyocera Corporation ++lacie LaCie ++laird Laird PLC ++lantiq Lantiq Semiconductor ++lattice Lattice Semiconductor ++lego LEGO Systems A/S ++lemaker Shenzhen LeMaker Technology Co., Ltd. ++lenovo Lenovo Group Ltd. ++lg LG Corporation ++libretech Shenzhen Libre Technology Co., Ltd ++licheepi Lichee Pi ++linaro Linaro Limited ++linksys Belkin International, Inc. (Linksys) ++linux Linux-specific binding ++linx Linx Technologies ++lltc Linear Technology Corporation ++logicpd Logic PD, Inc. ++lsi LSI Corp. (LSI Logic) ++lwn Liebherr-Werk Nenzing GmbH ++macnica Macnica Americas ++marvell Marvell Technology Group Ltd. ++maxim Maxim Integrated Products ++mbvl Mobiveil Inc. ++mcube mCube ++meas Measurement Specialties ++mediatek MediaTek Inc. ++megachips MegaChips ++mele Shenzhen MeLE Digital Technology Ltd. ++melexis Melexis N.V. ++melfas MELFAS Inc. ++mellanox Mellanox Technologies ++memsic MEMSIC Inc. ++merrii Merrii Technology Co., Ltd. ++micrel Micrel Inc. ++microchip Microchip Technology Inc. ++microcrystal Micro Crystal AG ++micron Micron Technology Inc. ++mikroe MikroElektronika d.o.o. ++minix MINIX Technology Ltd. ++miramems MiraMEMS Sensing Technology Co., Ltd. ++mitsubishi Mitsubishi Electric Corporation ++mosaixtech Mosaix Technologies, Inc. ++motorola Motorola, Inc. ++moxa Moxa Inc. ++mpl MPL AG ++mqmaker mqmaker Inc. ++mscc Microsemi Corporation ++msi Micro-Star International Co. Ltd. ++mti Imagination Technologies Ltd. (formerly MIPS Technologies Inc.) ++multi-inno Multi-Inno Technology Co.,Ltd ++mundoreader Mundo Reader S.L. ++murata Murata Manufacturing Co., Ltd. ++mxicy Macronix International Co., Ltd. ++myir MYIR Tech Limited ++national National Semiconductor ++nec NEC LCD Technologies, Ltd. ++neonode Neonode Inc. ++netgear NETGEAR ++netlogic Broadcom Corporation (formerly NetLogic Microsystems) ++netron-dy Netron DY ++netxeon Shenzhen Netxeon Technology CO., LTD ++nexbox Nexbox ++nextthing Next Thing Co. ++newhaven Newhaven Display International ++ni National Instruments ++nintendo Nintendo ++nlt NLT Technologies, Ltd. ++nokia Nokia ++nordic Nordic Semiconductor ++novtech NovTech, Inc. ++nutsboard NutsBoard ++nuvoton Nuvoton Technology Corporation ++nvd New Vision Display ++nvidia NVIDIA ++nxp NXP Semiconductors ++okaya Okaya Electric America, Inc. ++oki Oki Electric Industry Co., Ltd. ++olimex OLIMEX Ltd. ++olpc One Laptop Per Child ++onion Onion Corporation ++onnn ON Semiconductor Corp. ++ontat On Tat Industrial Company ++opalkelly Opal Kelly Incorporated ++opencores OpenCores.org ++openrisc OpenRISC.io ++option Option NV ++oranth Shenzhen Oranth Technology Co., Ltd. ++ORCL Oracle Corporation ++orisetech Orise Technology ++ortustech Ortus Technology Co., Ltd. ++ovti OmniVision Technologies ++oxsemi Oxford Semiconductor, Ltd. ++panasonic Panasonic Corporation ++parade Parade Technologies Inc. ++pda Precision Design Associates, Inc. ++pericom Pericom Technology Inc. ++pervasive Pervasive Displays, Inc. ++phicomm PHICOMM Co., Ltd. ++phytec PHYTEC Messtechnik GmbH ++picochip Picochip Ltd ++pine64 Pine64 ++pixcir PIXCIR MICROELECTRONICS Co., Ltd ++plantower Plantower Co., Ltd ++plathome Plat'Home Co., Ltd. ++plda PLDA ++plx Broadcom Corporation (formerly PLX Technology) ++pni PNI Sensor Corporation ++portwell Portwell Inc. ++poslab Poslab Technology Co., Ltd. ++powervr PowerVR (deprecated, use img) ++probox2 PROBOX2 (by W2COMP Co., Ltd.) ++pulsedlight PulsedLight, Inc ++qca Qualcomm Atheros, Inc. ++qcom Qualcomm Technologies, Inc ++qemu QEMU, a generic and open source machine emulator and virtualizer ++qi Qi Hardware ++qiaodian QiaoDian XianShi Corporation ++qnap QNAP Systems, Inc. ++radxa Radxa ++raidsonic RaidSonic Technology GmbH ++ralink Mediatek/Ralink Technology Corp. ++ramtron Ramtron International ++raspberrypi Raspberry Pi Foundation ++raydium Raydium Semiconductor Corp. ++rda Unisoc Communications, Inc. ++realtek Realtek Semiconductor Corp. ++renesas Renesas Electronics Corporation ++richtek Richtek Technology Corporation ++ricoh Ricoh Co. Ltd. ++rikomagic Rikomagic Tech Corp. Ltd ++riscv RISC-V Foundation ++rockchip Fuzhou Rockchip Electronics Co., Ltd ++rohm ROHM Semiconductor Co., Ltd ++roofull Shenzhen Roofull Technology Co, Ltd ++samsung Samsung Semiconductor ++samtec Samtec/Softing company ++sancloud Sancloud Ltd ++sandisk Sandisk Corporation ++sbs Smart Battery System ++schindler Schindler ++seagate Seagate Technology PLC ++semtech Semtech Corporation ++sensirion Sensirion AG ++sff Small Form Factor Committee ++sgd Solomon Goldentek Display Corporation ++sgx SGX Sensortech ++sharp Sharp Corporation ++shimafuji Shimafuji Electric, Inc. ++si-en Si-En Technology Ltd. ++sifive SiFive, Inc. ++sigma Sigma Designs, Inc. ++sii Seiko Instruments, Inc. ++sil Silicon Image ++silabs Silicon Laboratories ++silead Silead Inc. ++silergy Silergy Corp. ++siliconmitus Silicon Mitus, Inc. ++simtek ++sirf SiRF Technology, Inc. ++sis Silicon Integrated Systems Corp. ++sitronix Sitronix Technology Corporation ++skyworks Skyworks Solutions, Inc. ++smsc Standard Microsystems Corporation ++snps Synopsys, Inc. ++socionext Socionext Inc. ++solidrun SolidRun ++solomon Solomon Systech Limited ++sony Sony Corporation ++spansion Spansion Inc. ++sprd Spreadtrum Communications Inc. ++sst Silicon Storage Technology, Inc. ++st STMicroelectronics ++starry Starry Electronic Technology (ShenZhen) Co., LTD ++startek Startek ++ste ST-Ericsson ++stericsson ST-Ericsson ++summit Summit microelectronics ++sunchip Shenzhen Sunchip Technology Co., Ltd ++SUNW Sun Microsystems, Inc ++swir Sierra Wireless ++syna Synaptics Inc. ++synology Synology, Inc. ++tbs TBS Technologies ++tbs-biometrics Touchless Biometric Systems AG ++tcg Trusted Computing Group ++tcl Toby Churchill Ltd. ++technexion TechNexion ++technologic Technologic Systems ++tempo Tempo Semiconductor ++techstar Shenzhen Techstar Electronics Co., Ltd. ++terasic Terasic Inc. ++thine THine Electronics, Inc. ++ti Texas Instruments ++tianma Tianma Micro-electronics Co., Ltd. ++tlm Trusted Logic Mobility ++tmt Tecon Microprocessor Technologies, LLC. ++topeet Topeet ++toradex Toradex AG ++toshiba Toshiba Corporation ++toumaz Toumaz ++tpk TPK U.S.A. LLC ++tplink TP-LINK Technologies Co., Ltd. ++tpo TPO ++tronfy Tronfy ++tronsmart Tronsmart ++truly Truly Semiconductors Limited ++tsd Theobroma Systems Design und Consulting GmbH ++tyan Tyan Computer Corporation ++u-blox u-blox ++ucrobotics uCRobotics ++ubnt Ubiquiti Networks ++udoo Udoo ++uniwest United Western Technologies Corp (UniWest) ++upisemi uPI Semiconductor Corp. ++urt United Radiant Technology Corporation ++usi Universal Scientific Industrial Co., Ltd. ++v3 V3 Semiconductor ++vamrs Vamrs Ltd. ++variscite Variscite Ltd. ++via VIA Technologies, Inc. ++virtio Virtual I/O Device Specification, developed by the OASIS consortium ++vishay Vishay Intertechnology, Inc ++vitesse Vitesse Semiconductor Corporation ++vivante Vivante Corporation ++vocore VoCore Studio ++voipac Voipac Technologies s.r.o. ++vot Vision Optical Technology Co., Ltd. ++wd Western Digital Corp. ++wetek WeTek Electronics, limited. ++wexler Wexler ++whwave Shenzhen whwave Electronics, Inc. ++wi2wi Wi2Wi, Inc. ++winbond Winbond Electronics corp. ++winstar Winstar Display Corp. ++wlf Wolfson Microelectronics ++wm Wondermedia Technologies, Inc. ++x-powers X-Powers ++xes Extreme Engineering Solutions (X-ES) ++xillybus Xillybus Ltd. ++xlnx Xilinx ++xunlong Shenzhen Xunlong Software CO.,Limited ++ysoft Y Soft Corporation a.s. ++zarlink Zarlink Semiconductor ++zeitec ZEITEC Semiconductor Co., LTD. ++zidoo Shenzhen Zidoo Technology Co., Ltd. ++zii Zodiac Inflight Innovations ++zte ZTE Corp. ++zyxel ZyXEL Communications Corp. +--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml ++++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml +@@ -159,6 +159,8 @@ patternProperties: + description: Beckhoff Automation GmbH & Co. KG + "^bitmain,.*": + description: Bitmain Technologies ++ "^blokaslabs,.*": ++ description: Vilniaus Blokas UAB + "^boe,.*": + description: BOE Technology Group Co., Ltd. + "^bosch,.*": +--- a/drivers/clk/Kconfig ++++ b/drivers/clk/Kconfig +@@ -86,6 +86,12 @@ config COMMON_CLK_HI655X + multi-function device has one fixed-rate oscillator, clocked + at 32KHz. + ++config COMMON_CLK_HIFIBERRY_DACPLUSHD ++ tristate ++ ++config COMMON_CLK_HIFIBERRY_DACPRO ++ tristate ++ + config COMMON_CLK_SCMI + tristate "Clock driver controlled via SCMI interface" + depends on ARM_SCMI_PROTOCOL || COMPILE_TEST +--- a/drivers/clk/Makefile ++++ b/drivers/clk/Makefile +@@ -18,6 +18,7 @@ endif + + # hardware specific clock types + # please keep this section sorted lexicographically by file path name ++obj-$(CONFIG_SND_BCM2708_SOC_ALLO_BOSS_DAC) += clk-allo-dac.o + obj-$(CONFIG_MACH_ASM9260) += clk-asm9260.o + obj-$(CONFIG_COMMON_CLK_AXI_CLKGEN) += clk-axi-clkgen.o + obj-$(CONFIG_ARCH_AXXIA) += clk-axm5516.o +@@ -37,6 +38,8 @@ obj-$(CONFIG_MACH_ASPEED_G6) += clk-ast + obj-$(CONFIG_ARCH_HIGHBANK) += clk-highbank.o + obj-$(CONFIG_CLK_HSDK) += clk-hsdk-pll.o + obj-$(CONFIG_COMMON_CLK_LOCHNAGAR) += clk-lochnagar.o ++obj-$(CONFIG_COMMON_CLK_HIFIBERRY_DACPRO) += clk-hifiberry-dacpro.o ++obj-$(CONFIG_COMMON_CLK_HIFIBERRY_DACPLUSHD) += clk-hifiberry-dachd.o + obj-$(CONFIG_COMMON_CLK_MAX77686) += clk-max77686.o + obj-$(CONFIG_COMMON_CLK_MAX9485) += clk-max9485.o + obj-$(CONFIG_ARCH_MILBEAUT_M10V) += clk-milbeaut.o +--- /dev/null ++++ b/drivers/clk/clk-allo-dac.c +@@ -0,0 +1,161 @@ ++/* ++ * Clock Driver for Allo DAC ++ * ++ * Author: Baswaraj K ++ * Copyright 2016 ++ * based on code by Stuart MacLean ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++/* Clock rate of CLK44EN attached to GPIO6 pin */ ++#define CLK_44EN_RATE 45158400UL ++/* Clock rate of CLK48EN attached to GPIO3 pin */ ++#define CLK_48EN_RATE 49152000UL ++ ++/** ++ * struct allo_dac_clk - Common struct to the Allo DAC ++ * @hw: clk_hw for the common clk framework ++ * @mode: 0 => CLK44EN, 1 => CLK48EN ++ */ ++struct clk_allo_hw { ++ struct clk_hw hw; ++ uint8_t mode; ++}; ++ ++#define to_allo_clk(_hw) container_of(_hw, struct clk_allo_hw, hw) ++ ++static const struct of_device_id clk_allo_dac_dt_ids[] = { ++ { .compatible = "allo,dac-clk",}, ++ { } ++}; ++MODULE_DEVICE_TABLE(of, clk_allo_dac_dt_ids); ++ ++static unsigned long clk_allo_dac_recalc_rate(struct clk_hw *hw, ++ unsigned long parent_rate) ++{ ++ return (to_allo_clk(hw)->mode == 0) ? CLK_44EN_RATE : ++ CLK_48EN_RATE; ++} ++ ++static long clk_allo_dac_round_rate(struct clk_hw *hw, ++ unsigned long rate, unsigned long *parent_rate) ++{ ++ long actual_rate; ++ ++ if (rate <= CLK_44EN_RATE) { ++ actual_rate = (long)CLK_44EN_RATE; ++ } else if (rate >= CLK_48EN_RATE) { ++ actual_rate = (long)CLK_48EN_RATE; ++ } else { ++ long diff44Rate = (long)(rate - CLK_44EN_RATE); ++ long diff48Rate = (long)(CLK_48EN_RATE - rate); ++ ++ if (diff44Rate < diff48Rate) ++ actual_rate = (long)CLK_44EN_RATE; ++ else ++ actual_rate = (long)CLK_48EN_RATE; ++ } ++ return actual_rate; ++} ++ ++ ++static int clk_allo_dac_set_rate(struct clk_hw *hw, ++ unsigned long rate, unsigned long parent_rate) ++{ ++ unsigned long actual_rate; ++ struct clk_allo_hw *clk = to_allo_clk(hw); ++ ++ actual_rate = (unsigned long)clk_allo_dac_round_rate(hw, rate, ++ &parent_rate); ++ clk->mode = (actual_rate == CLK_44EN_RATE) ? 0 : 1; ++ return 0; ++} ++ ++ ++const struct clk_ops clk_allo_dac_rate_ops = { ++ .recalc_rate = clk_allo_dac_recalc_rate, ++ .round_rate = clk_allo_dac_round_rate, ++ .set_rate = clk_allo_dac_set_rate, ++}; ++ ++static int clk_allo_dac_probe(struct platform_device *pdev) ++{ ++ int ret; ++ struct clk_allo_hw *proclk; ++ struct clk *clk; ++ struct device *dev; ++ struct clk_init_data init; ++ ++ dev = &pdev->dev; ++ ++ proclk = kzalloc(sizeof(struct clk_allo_hw), GFP_KERNEL); ++ if (!proclk) ++ return -ENOMEM; ++ ++ init.name = "clk-allo-dac"; ++ init.ops = &clk_allo_dac_rate_ops; ++ init.flags = 0; ++ init.parent_names = NULL; ++ init.num_parents = 0; ++ ++ proclk->mode = 0; ++ proclk->hw.init = &init; ++ ++ clk = devm_clk_register(dev, &proclk->hw); ++ if (!IS_ERR(clk)) { ++ ret = of_clk_add_provider(dev->of_node, of_clk_src_simple_get, ++ clk); ++ } else { ++ dev_err(dev, "Fail to register clock driver\n"); ++ kfree(proclk); ++ ret = PTR_ERR(clk); ++ } ++ return ret; ++} ++ ++static int clk_allo_dac_remove(struct platform_device *pdev) ++{ ++ of_clk_del_provider(pdev->dev.of_node); ++ return 0; ++} ++ ++static struct platform_driver clk_allo_dac_driver = { ++ .probe = clk_allo_dac_probe, ++ .remove = clk_allo_dac_remove, ++ .driver = { ++ .name = "clk-allo-dac", ++ .of_match_table = clk_allo_dac_dt_ids, ++ }, ++}; ++ ++static int __init clk_allo_dac_init(void) ++{ ++ return platform_driver_register(&clk_allo_dac_driver); ++} ++core_initcall(clk_allo_dac_init); ++ ++static void __exit clk_allo_dac_exit(void) ++{ ++ platform_driver_unregister(&clk_allo_dac_driver); ++} ++module_exit(clk_allo_dac_exit); ++ ++MODULE_DESCRIPTION("Allo DAC clock driver"); ++MODULE_LICENSE("GPL v2"); ++MODULE_ALIAS("platform:clk-allo-dac"); +--- /dev/null ++++ b/drivers/clk/clk-hifiberry-dachd.c +@@ -0,0 +1,333 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * Clock Driver for HiFiBerry DAC+ HD ++ * ++ * Author: Joerg Schambacher, i2Audio GmbH for HiFiBerry ++ * Copyright 2020 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define NO_PLL_RESET 0 ++#define PLL_RESET 1 ++#define HIFIBERRY_PLL_MAX_REGISTER 256 ++#define DEFAULT_RATE 44100 ++ ++static struct reg_default hifiberry_pll_reg_defaults[] = { ++ {0x02, 0x53}, {0x03, 0x00}, {0x07, 0x20}, {0x0F, 0x00}, ++ {0x10, 0x0D}, {0x11, 0x1D}, {0x12, 0x0D}, {0x13, 0x8C}, ++ {0x14, 0x8C}, {0x15, 0x8C}, {0x16, 0x8C}, {0x17, 0x8C}, ++ {0x18, 0x2A}, {0x1C, 0x00}, {0x1D, 0x0F}, {0x1F, 0x00}, ++ {0x2A, 0x00}, {0x2C, 0x00}, {0x2F, 0x00}, {0x30, 0x00}, ++ {0x31, 0x00}, {0x32, 0x00}, {0x34, 0x00}, {0x37, 0x00}, ++ {0x38, 0x00}, {0x39, 0x00}, {0x3A, 0x00}, {0x3B, 0x01}, ++ {0x3E, 0x00}, {0x3F, 0x00}, {0x40, 0x00}, {0x41, 0x00}, ++ {0x5A, 0x00}, {0x5B, 0x00}, {0x95, 0x00}, {0x96, 0x00}, ++ {0x97, 0x00}, {0x98, 0x00}, {0x99, 0x00}, {0x9A, 0x00}, ++ {0x9B, 0x00}, {0xA2, 0x00}, {0xA3, 0x00}, {0xA4, 0x00}, ++ {0xB7, 0x92}, ++ {0x1A, 0x3D}, {0x1B, 0x09}, {0x1E, 0xF3}, {0x20, 0x13}, ++ {0x21, 0x75}, {0x2B, 0x04}, {0x2D, 0x11}, {0x2E, 0xE0}, ++ {0x3D, 0x7A}, ++ {0x35, 0x9D}, {0x36, 0x00}, {0x3C, 0x42}, ++ { 177, 0xAC}, ++}; ++static struct reg_default common_pll_regs[HIFIBERRY_PLL_MAX_REGISTER]; ++static int num_common_pll_regs; ++static struct reg_default dedicated_192k_pll_regs[HIFIBERRY_PLL_MAX_REGISTER]; ++static int num_dedicated_192k_pll_regs; ++static struct reg_default dedicated_96k_pll_regs[HIFIBERRY_PLL_MAX_REGISTER]; ++static int num_dedicated_96k_pll_regs; ++static struct reg_default dedicated_48k_pll_regs[HIFIBERRY_PLL_MAX_REGISTER]; ++static int num_dedicated_48k_pll_regs; ++static struct reg_default dedicated_176k4_pll_regs[HIFIBERRY_PLL_MAX_REGISTER]; ++static int num_dedicated_176k4_pll_regs; ++static struct reg_default dedicated_88k2_pll_regs[HIFIBERRY_PLL_MAX_REGISTER]; ++static int num_dedicated_88k2_pll_regs; ++static struct reg_default dedicated_44k1_pll_regs[HIFIBERRY_PLL_MAX_REGISTER]; ++static int num_dedicated_44k1_pll_regs; ++ ++/** ++ * struct clk_hifiberry_drvdata - Common struct to the HiFiBerry DAC HD Clk ++ * @hw: clk_hw for the common clk framework ++ */ ++struct clk_hifiberry_drvdata { ++ struct regmap *regmap; ++ struct clk *clk; ++ struct clk_hw hw; ++ unsigned long rate; ++}; ++ ++#define to_hifiberry_clk(_hw) \ ++ container_of(_hw, struct clk_hifiberry_drvdata, hw) ++ ++static int clk_hifiberry_dachd_write_pll_regs(struct regmap *regmap, ++ struct reg_default *regs, ++ int num, int do_pll_reset) ++{ ++ int i; ++ int ret = 0; ++ char pll_soft_reset[] = { 177, 0xAC, }; ++ ++ for (i = 0; i < num; i++) { ++ ret |= regmap_write(regmap, regs[i].reg, regs[i].def); ++ if (ret) ++ return ret; ++ } ++ if (do_pll_reset) { ++ ret |= regmap_write(regmap, pll_soft_reset[0], ++ pll_soft_reset[1]); ++ mdelay(10); ++ } ++ return ret; ++} ++ ++static unsigned long clk_hifiberry_dachd_recalc_rate(struct clk_hw *hw, ++ unsigned long parent_rate) ++{ ++ return to_hifiberry_clk(hw)->rate; ++} ++ ++static long clk_hifiberry_dachd_round_rate(struct clk_hw *hw, ++ unsigned long rate, unsigned long *parent_rate) ++{ ++ return rate; ++} ++ ++static int clk_hifiberry_dachd_set_rate(struct clk_hw *hw, ++ unsigned long rate, unsigned long parent_rate) ++{ ++ int ret; ++ struct clk_hifiberry_drvdata *drvdata = to_hifiberry_clk(hw); ++ ++ switch (rate) { ++ case 44100: ++ ret = clk_hifiberry_dachd_write_pll_regs(drvdata->regmap, ++ dedicated_44k1_pll_regs, num_dedicated_44k1_pll_regs, ++ PLL_RESET); ++ break; ++ case 88200: ++ ret = clk_hifiberry_dachd_write_pll_regs(drvdata->regmap, ++ dedicated_88k2_pll_regs, num_dedicated_88k2_pll_regs, ++ PLL_RESET); ++ break; ++ case 176400: ++ ret = clk_hifiberry_dachd_write_pll_regs(drvdata->regmap, ++ dedicated_176k4_pll_regs, num_dedicated_176k4_pll_regs, ++ PLL_RESET); ++ break; ++ case 48000: ++ ret = clk_hifiberry_dachd_write_pll_regs(drvdata->regmap, ++ dedicated_48k_pll_regs, num_dedicated_48k_pll_regs, ++ PLL_RESET); ++ break; ++ case 96000: ++ ret = clk_hifiberry_dachd_write_pll_regs(drvdata->regmap, ++ dedicated_96k_pll_regs, num_dedicated_96k_pll_regs, ++ PLL_RESET); ++ break; ++ case 192000: ++ ret = clk_hifiberry_dachd_write_pll_regs(drvdata->regmap, ++ dedicated_192k_pll_regs, num_dedicated_192k_pll_regs, ++ PLL_RESET); ++ break; ++ default: ++ ret = -EINVAL; ++ break; ++ } ++ to_hifiberry_clk(hw)->rate = rate; ++ ++ return ret; ++} ++ ++const struct clk_ops clk_hifiberry_dachd_rate_ops = { ++ .recalc_rate = clk_hifiberry_dachd_recalc_rate, ++ .round_rate = clk_hifiberry_dachd_round_rate, ++ .set_rate = clk_hifiberry_dachd_set_rate, ++}; ++ ++static int clk_hifiberry_get_prop_values(struct device *dev, ++ char *prop_name, ++ struct reg_default *regs) ++{ ++ int ret; ++ int i; ++ u8 tmp[2 * HIFIBERRY_PLL_MAX_REGISTER]; ++ ++ ret = of_property_read_variable_u8_array(dev->of_node, prop_name, ++ tmp, 0, 2 * HIFIBERRY_PLL_MAX_REGISTER); ++ if (ret < 0) ++ return ret; ++ if (ret & 1) { ++ dev_err(dev, ++ "%s <%s> -> #%i odd number of bytes for reg/val pairs!", ++ __func__, ++ prop_name, ++ ret); ++ return -EINVAL; ++ } ++ ret /= 2; ++ for (i = 0; i < ret; i++) { ++ regs[i].reg = (u32)tmp[2 * i]; ++ regs[i].def = (u32)tmp[2 * i + 1]; ++ } ++ return ret; ++} ++ ++ ++static int clk_hifiberry_dachd_dt_parse(struct device *dev) ++{ ++ num_common_pll_regs = clk_hifiberry_get_prop_values(dev, ++ "common_pll_regs", common_pll_regs); ++ num_dedicated_44k1_pll_regs = clk_hifiberry_get_prop_values(dev, ++ "44k1_pll_regs", dedicated_44k1_pll_regs); ++ num_dedicated_88k2_pll_regs = clk_hifiberry_get_prop_values(dev, ++ "88k2_pll_regs", dedicated_88k2_pll_regs); ++ num_dedicated_176k4_pll_regs = clk_hifiberry_get_prop_values(dev, ++ "176k4_pll_regs", dedicated_176k4_pll_regs); ++ num_dedicated_48k_pll_regs = clk_hifiberry_get_prop_values(dev, ++ "48k_pll_regs", dedicated_48k_pll_regs); ++ num_dedicated_96k_pll_regs = clk_hifiberry_get_prop_values(dev, ++ "96k_pll_regs", dedicated_96k_pll_regs); ++ num_dedicated_192k_pll_regs = clk_hifiberry_get_prop_values(dev, ++ "192k_pll_regs", dedicated_192k_pll_regs); ++ return 0; ++} ++ ++ ++static int clk_hifiberry_dachd_remove(struct device *dev) ++{ ++ of_clk_del_provider(dev->of_node); ++ return 0; ++} ++ ++const struct regmap_config hifiberry_pll_regmap = { ++ .reg_bits = 8, ++ .val_bits = 8, ++ .max_register = HIFIBERRY_PLL_MAX_REGISTER, ++ .reg_defaults = hifiberry_pll_reg_defaults, ++ .num_reg_defaults = ARRAY_SIZE(hifiberry_pll_reg_defaults), ++ .cache_type = REGCACHE_RBTREE, ++}; ++EXPORT_SYMBOL_GPL(hifiberry_pll_regmap); ++ ++ ++static int clk_hifiberry_dachd_i2c_probe(struct i2c_client *i2c, ++ const struct i2c_device_id *id) ++{ ++ struct clk_hifiberry_drvdata *hdclk; ++ int ret = 0; ++ struct clk_init_data init; ++ struct device *dev = &i2c->dev; ++ struct device_node *dev_node = dev->of_node; ++ struct regmap_config config = hifiberry_pll_regmap; ++ ++ hdclk = devm_kzalloc(&i2c->dev, ++ sizeof(struct clk_hifiberry_drvdata), GFP_KERNEL); ++ if (!hdclk) ++ return -ENOMEM; ++ ++ i2c_set_clientdata(i2c, hdclk); ++ ++ hdclk->regmap = devm_regmap_init_i2c(i2c, &config); ++ ++ if (IS_ERR(hdclk->regmap)) ++ return PTR_ERR(hdclk->regmap); ++ ++ /* start PLL to allow detection of DAC */ ++ ret = clk_hifiberry_dachd_write_pll_regs(hdclk->regmap, ++ hifiberry_pll_reg_defaults, ++ ARRAY_SIZE(hifiberry_pll_reg_defaults), ++ PLL_RESET); ++ if (ret) ++ return ret; ++ ++ clk_hifiberry_dachd_dt_parse(dev); ++ ++ /* restart PLL with configs from DTB */ ++ ret = clk_hifiberry_dachd_write_pll_regs(hdclk->regmap, common_pll_regs, ++ num_common_pll_regs, PLL_RESET); ++ if (ret) ++ return ret; ++ ++ init.name = "clk-hifiberry-dachd"; ++ init.ops = &clk_hifiberry_dachd_rate_ops; ++ init.flags = 0; ++ init.parent_names = NULL; ++ init.num_parents = 0; ++ ++ hdclk->hw.init = &init; ++ ++ hdclk->clk = devm_clk_register(dev, &hdclk->hw); ++ if (IS_ERR(hdclk->clk)) { ++ dev_err(dev, "unable to register %s\n", init.name); ++ return PTR_ERR(hdclk->clk); ++ } ++ ++ ret = of_clk_add_provider(dev_node, of_clk_src_simple_get, hdclk->clk); ++ if (ret != 0) { ++ dev_err(dev, "Cannot of_clk_add_provider"); ++ return ret; ++ } ++ ++ ret = clk_set_rate(hdclk->hw.clk, DEFAULT_RATE); ++ if (ret != 0) { ++ dev_err(dev, "Cannot set rate : %d\n", ret); ++ return -EINVAL; ++ } ++ ++ return ret; ++} ++ ++static int clk_hifiberry_dachd_i2c_remove(struct i2c_client *i2c) ++{ ++ clk_hifiberry_dachd_remove(&i2c->dev); ++ return 0; ++} ++ ++static const struct i2c_device_id clk_hifiberry_dachd_i2c_id[] = { ++ { "dachd-clk", }, ++ { } ++}; ++MODULE_DEVICE_TABLE(i2c, clk_hifiberry_dachd_i2c_id); ++ ++static const struct of_device_id clk_hifiberry_dachd_of_match[] = { ++ { .compatible = "hifiberry,dachd-clk", }, ++ { } ++}; ++MODULE_DEVICE_TABLE(of, clk_hifiberry_dachd_of_match); ++ ++static struct i2c_driver clk_hifiberry_dachd_i2c_driver = { ++ .probe = clk_hifiberry_dachd_i2c_probe, ++ .remove = clk_hifiberry_dachd_i2c_remove, ++ .id_table = clk_hifiberry_dachd_i2c_id, ++ .driver = { ++ .name = "dachd-clk", ++ .of_match_table = of_match_ptr(clk_hifiberry_dachd_of_match), ++ }, ++}; ++ ++module_i2c_driver(clk_hifiberry_dachd_i2c_driver); ++ ++ ++MODULE_DESCRIPTION("HiFiBerry DAC+ HD clock driver"); ++MODULE_AUTHOR("Joerg Schambacher "); ++MODULE_LICENSE("GPL v2"); ++MODULE_ALIAS("platform:clk-hifiberry-dachd"); +--- /dev/null ++++ b/drivers/clk/clk-hifiberry-dacpro.c +@@ -0,0 +1,160 @@ ++/* ++ * Clock Driver for HiFiBerry DAC Pro ++ * ++ * Author: Stuart MacLean ++ * Copyright 2015 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++/* Clock rate of CLK44EN attached to GPIO6 pin */ ++#define CLK_44EN_RATE 22579200UL ++/* Clock rate of CLK48EN attached to GPIO3 pin */ ++#define CLK_48EN_RATE 24576000UL ++ ++/** ++ * struct hifiberry_dacpro_clk - Common struct to the HiFiBerry DAC Pro ++ * @hw: clk_hw for the common clk framework ++ * @mode: 0 => CLK44EN, 1 => CLK48EN ++ */ ++struct clk_hifiberry_hw { ++ struct clk_hw hw; ++ uint8_t mode; ++}; ++ ++#define to_hifiberry_clk(_hw) container_of(_hw, struct clk_hifiberry_hw, hw) ++ ++static const struct of_device_id clk_hifiberry_dacpro_dt_ids[] = { ++ { .compatible = "hifiberry,dacpro-clk",}, ++ { } ++}; ++MODULE_DEVICE_TABLE(of, clk_hifiberry_dacpro_dt_ids); ++ ++static unsigned long clk_hifiberry_dacpro_recalc_rate(struct clk_hw *hw, ++ unsigned long parent_rate) ++{ ++ return (to_hifiberry_clk(hw)->mode == 0) ? CLK_44EN_RATE : ++ CLK_48EN_RATE; ++} ++ ++static long clk_hifiberry_dacpro_round_rate(struct clk_hw *hw, ++ unsigned long rate, unsigned long *parent_rate) ++{ ++ long actual_rate; ++ ++ if (rate <= CLK_44EN_RATE) { ++ actual_rate = (long)CLK_44EN_RATE; ++ } else if (rate >= CLK_48EN_RATE) { ++ actual_rate = (long)CLK_48EN_RATE; ++ } else { ++ long diff44Rate = (long)(rate - CLK_44EN_RATE); ++ long diff48Rate = (long)(CLK_48EN_RATE - rate); ++ ++ if (diff44Rate < diff48Rate) ++ actual_rate = (long)CLK_44EN_RATE; ++ else ++ actual_rate = (long)CLK_48EN_RATE; ++ } ++ return actual_rate; ++} ++ ++ ++static int clk_hifiberry_dacpro_set_rate(struct clk_hw *hw, ++ unsigned long rate, unsigned long parent_rate) ++{ ++ unsigned long actual_rate; ++ struct clk_hifiberry_hw *clk = to_hifiberry_clk(hw); ++ ++ actual_rate = (unsigned long)clk_hifiberry_dacpro_round_rate(hw, rate, ++ &parent_rate); ++ clk->mode = (actual_rate == CLK_44EN_RATE) ? 0 : 1; ++ return 0; ++} ++ ++ ++const struct clk_ops clk_hifiberry_dacpro_rate_ops = { ++ .recalc_rate = clk_hifiberry_dacpro_recalc_rate, ++ .round_rate = clk_hifiberry_dacpro_round_rate, ++ .set_rate = clk_hifiberry_dacpro_set_rate, ++}; ++ ++static int clk_hifiberry_dacpro_probe(struct platform_device *pdev) ++{ ++ int ret; ++ struct clk_hifiberry_hw *proclk; ++ struct clk *clk; ++ struct device *dev; ++ struct clk_init_data init; ++ ++ dev = &pdev->dev; ++ ++ proclk = kzalloc(sizeof(struct clk_hifiberry_hw), GFP_KERNEL); ++ if (!proclk) ++ return -ENOMEM; ++ ++ init.name = "clk-hifiberry-dacpro"; ++ init.ops = &clk_hifiberry_dacpro_rate_ops; ++ init.flags = 0; ++ init.parent_names = NULL; ++ init.num_parents = 0; ++ ++ proclk->mode = 0; ++ proclk->hw.init = &init; ++ ++ clk = devm_clk_register(dev, &proclk->hw); ++ if (!IS_ERR(clk)) { ++ ret = of_clk_add_provider(dev->of_node, of_clk_src_simple_get, ++ clk); ++ } else { ++ dev_err(dev, "Fail to register clock driver\n"); ++ kfree(proclk); ++ ret = PTR_ERR(clk); ++ } ++ return ret; ++} ++ ++static int clk_hifiberry_dacpro_remove(struct platform_device *pdev) ++{ ++ of_clk_del_provider(pdev->dev.of_node); ++ return 0; ++} ++ ++static struct platform_driver clk_hifiberry_dacpro_driver = { ++ .probe = clk_hifiberry_dacpro_probe, ++ .remove = clk_hifiberry_dacpro_remove, ++ .driver = { ++ .name = "clk-hifiberry-dacpro", ++ .of_match_table = clk_hifiberry_dacpro_dt_ids, ++ }, ++}; ++ ++static int __init clk_hifiberry_dacpro_init(void) ++{ ++ return platform_driver_register(&clk_hifiberry_dacpro_driver); ++} ++core_initcall(clk_hifiberry_dacpro_init); ++ ++static void __exit clk_hifiberry_dacpro_exit(void) ++{ ++ platform_driver_unregister(&clk_hifiberry_dacpro_driver); ++} ++module_exit(clk_hifiberry_dacpro_exit); ++ ++MODULE_DESCRIPTION("HiFiBerry DAC Pro clock driver"); ++MODULE_LICENSE("GPL v2"); ++MODULE_ALIAS("platform:clk-hifiberry-dacpro"); +--- a/sound/soc/bcm/Kconfig ++++ b/sound/soc/bcm/Kconfig +@@ -26,3 +26,277 @@ config SND_BCM63XX_I2S_WHISTLER + DSL/PON chips (bcm63158, bcm63178) + + If you don't know what to do here, say N ++ ++config SND_BCM2708_SOC_GOOGLEVOICEHAT_SOUNDCARD ++ tristate "Support for Google voiceHAT soundcard" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_VOICEHAT ++ select SND_RPI_SIMPLE_SOUNDCARD ++ help ++ Say Y or M if you want to add support for voiceHAT soundcard. ++ ++config SND_BCM2708_SOC_HIFIBERRY_DAC ++ tristate "Support for HifiBerry DAC" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_PCM5102A ++ select SND_RPI_SIMPLE_SOUNDCARD ++ help ++ Say Y or M if you want to add support for HifiBerry DAC. ++ ++config SND_BCM2708_SOC_HIFIBERRY_DACPLUS ++ tristate "Support for HifiBerry DAC+" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_PCM512x ++ select SND_SOC_TPA6130A2 ++ select COMMON_CLK_HIFIBERRY_DACPRO ++ help ++ Say Y or M if you want to add support for HifiBerry DAC+. ++ ++config SND_BCM2708_SOC_HIFIBERRY_DACPLUSHD ++ tristate "Support for HifiBerry DAC+ HD" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_PCM179X_I2C ++ select COMMON_CLK_HIFIBERRY_DACPLUSHD ++ help ++ Say Y or M if you want to add support for HifiBerry DAC+ HD. ++ ++config SND_BCM2708_SOC_HIFIBERRY_DACPLUSADC ++ tristate "Support for HifiBerry DAC+ADC" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_PCM512x_I2C ++ select SND_SOC_DMIC ++ select COMMON_CLK_HIFIBERRY_DACPRO ++ help ++ Say Y or M if you want to add support for HifiBerry DAC+ADC. ++ ++config SND_BCM2708_SOC_HIFIBERRY_DACPLUSADCPRO ++ tristate "Support for HifiBerry DAC+ADC PRO" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_PCM512x_I2C ++ select SND_SOC_PCM186X_I2C ++ select COMMON_CLK_HIFIBERRY_DACPRO ++ help ++ Say Y or M if you want to add support for HifiBerry DAC+ADC PRO. ++ ++config SND_BCM2708_SOC_HIFIBERRY_DACPLUSDSP ++ tristate "Support for HifiBerry DAC+DSP" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_RPI_SIMPLE_SOUNDCARD ++ help ++ Say Y or M if you want to add support for HifiBerry DSP-DAC. ++ ++config SND_BCM2708_SOC_HIFIBERRY_DIGI ++ tristate "Support for HifiBerry Digi" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_WM8804 ++ help ++ Say Y or M if you want to add support for HifiBerry Digi S/PDIF output board. ++ ++config SND_BCM2708_SOC_HIFIBERRY_AMP ++ tristate "Support for the HifiBerry Amp" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_TAS5713 ++ select SND_RPI_SIMPLE_SOUNDCARD ++ help ++ Say Y or M if you want to add support for the HifiBerry Amp amplifier board. ++ ++config SND_BCM2708_SOC_RPI_CIRRUS ++ tristate "Support for Cirrus Logic Audio Card" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_WM5102 ++ select SND_SOC_WM8804 ++ help ++ Say Y or M if you want to add support for the Wolfson and ++ Cirrus Logic audio cards. ++ ++config SND_BCM2708_SOC_RPI_DAC ++ tristate "Support for RPi-DAC" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_PCM1794A ++ select SND_RPI_SIMPLE_SOUNDCARD ++ help ++ Say Y or M if you want to add support for RPi-DAC. ++ ++config SND_BCM2708_SOC_RPI_PROTO ++ tristate "Support for Rpi-PROTO" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_WM8731 ++ help ++ Say Y or M if you want to add support for Audio Codec Board PROTO (WM8731). ++ ++config SND_BCM2708_SOC_JUSTBOOM_BOTH ++ tristate "Support for simultaneous JustBoom Digi and JustBoom DAC" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_WM8804 ++ select SND_SOC_PCM512x ++ help ++ Say Y or M if you want to add support for simultaneous ++ JustBoom Digi and JustBoom DAC. ++ ++ This is not the right choice if you only have one but both of ++ these cards. ++ ++config SND_BCM2708_SOC_JUSTBOOM_DAC ++ tristate "Support for JustBoom DAC" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_PCM512x ++ help ++ Say Y or M if you want to add support for JustBoom DAC. ++ ++config SND_BCM2708_SOC_JUSTBOOM_DIGI ++ tristate "Support for JustBoom Digi" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_WM8804 ++ select SND_RPI_WM8804_SOUNDCARD ++ help ++ Say Y or M if you want to add support for JustBoom Digi. ++ ++config SND_BCM2708_SOC_IQAUDIO_CODEC ++ tristate "Support for IQaudIO-CODEC" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_DA7213 ++ help ++ Say Y or M if you want to add support for IQaudIO-CODEC. ++ ++config SND_BCM2708_SOC_IQAUDIO_DAC ++ tristate "Support for IQaudIO-DAC" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_PCM512x_I2C ++ help ++ Say Y or M if you want to add support for IQaudIO-DAC. ++ ++config SND_BCM2708_SOC_IQAUDIO_DIGI ++ tristate "Support for IQAudIO Digi" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_WM8804 ++ select SND_RPI_WM8804_SOUNDCARD ++ help ++ Say Y or M if you want to add support for IQAudIO Digital IO board. ++ ++config SND_BCM2708_SOC_I_SABRE_Q2M ++ tristate "Support for Audiophonics I-Sabre Q2M DAC" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_I_SABRE_CODEC ++ help ++ Say Y or M if you want to add support for Audiophonics I-SABRE Q2M DAC ++ ++config SND_BCM2708_SOC_ADAU1977_ADC ++ tristate "Support for ADAU1977 ADC" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_ADAU1977_I2C ++ select SND_RPI_SIMPLE_SOUNDCARD ++ help ++ Say Y or M if you want to add support for ADAU1977 ADC. ++ ++config SND_AUDIOINJECTOR_PI_SOUNDCARD ++ tristate "Support for audioinjector.net Pi add on soundcard" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_WM8731 ++ help ++ Say Y or M if you want to add support for audioinjector.net Pi Hat ++ ++config SND_AUDIOINJECTOR_OCTO_SOUNDCARD ++ tristate "Support for audioinjector.net Octo channel (Hat) soundcard" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_CS42XX8_I2C ++ help ++ Say Y or M if you want to add support for audioinjector.net octo add on ++ ++config SND_AUDIOINJECTOR_ISOLATED_SOUNDCARD ++ tristate "Support for audioinjector.net isolated DAC and ADC soundcard" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_CS4271_I2C ++ help ++ Say Y or M if you want to add support for audioinjector.net isolated soundcard ++ ++config SND_AUDIOSENSE_PI ++ tristate "Support for AudioSense Add-On Soundcard" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_TLV320AIC32X4_I2C ++ help ++ Say Y or M if you want to add support for tlv320aic32x4 add-on ++ ++config SND_DIGIDAC1_SOUNDCARD ++ tristate "Support for Red Rocks Audio DigiDAC1" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_WM8804 ++ select SND_SOC_WM8741 ++ help ++ Say Y or M if you want to add support for Red Rocks Audio DigiDAC1 board. ++ ++config SND_BCM2708_SOC_DIONAUDIO_LOCO ++ tristate "Support for Dion Audio LOCO DAC-AMP" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_PCM5102a ++ help ++ Say Y or M if you want to add support for Dion Audio LOCO. ++ ++config SND_BCM2708_SOC_DIONAUDIO_LOCO_V2 ++ tristate "Support for Dion Audio LOCO-V2 DAC-AMP" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_PCM5122 ++ help ++ Say Y or M if you want to add support for Dion Audio LOCO-V2. ++ ++config SND_BCM2708_SOC_ALLO_PIANO_DAC ++ tristate "Support for Allo Piano DAC" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_PCM512x_I2C ++ help ++ Say Y or M if you want to add support for Allo Piano DAC. ++ ++config SND_BCM2708_SOC_ALLO_PIANO_DAC_PLUS ++ tristate "Support for Allo Piano DAC Plus" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_PCM512x_I2C ++ help ++ Say Y or M if you want to add support for Allo Piano DAC Plus. ++ ++config SND_BCM2708_SOC_ALLO_BOSS_DAC ++ tristate "Support for Allo Boss DAC" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_PCM512x_I2C ++ help ++ Say Y or M if you want to add support for Allo Boss DAC. ++ ++config SND_BCM2708_SOC_ALLO_DIGIONE ++ tristate "Support for Allo DigiOne" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_WM8804 ++ select SND_RPI_WM8804_SOUNDCARD ++ help ++ Say Y or M if you want to add support for Allo DigiOne. ++ ++config SND_BCM2708_SOC_ALLO_KATANA_DAC ++ tristate "Support for Allo Katana DAC" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ depends on I2C ++ select REGMAP_I2C ++ select SND_AUDIO_GRAPH_CARD ++ help ++ Say Y or M if you want to add support for Allo Katana DAC. ++ ++config SND_BCM2708_SOC_FE_PI_AUDIO ++ tristate "Support for Fe-Pi-Audio" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_SOC_SGTL5000 ++ help ++ Say Y or M if you want to add support for Fe-Pi-Audio. ++ ++config SND_PISOUND ++ tristate "Support for Blokas Labs pisound" ++ depends on SND_BCM2708_SOC_I2S || SND_BCM2835_SOC_I2S ++ select SND_RAWMIDI ++ help ++ Say Y or M if you want to add support for Blokas Labs pisound. ++ ++config SND_RPI_SIMPLE_SOUNDCARD ++ tristate "Support for Raspberry Pi simple soundcards" ++ help ++ Say Y or M if you want to add support Raspbery Pi simple soundcards ++ ++config SND_RPI_WM8804_SOUNDCARD ++ tristate "Support for Raspberry Pi generic WM8804 soundcards" ++ help ++ Say Y or M if you want to add support for the Raspberry Pi ++ generic driver for WM8804 based soundcards. +--- a/sound/soc/bcm/Makefile ++++ b/sound/soc/bcm/Makefile +@@ -12,4 +12,65 @@ obj-$(CONFIG_SND_SOC_CYGNUS) += snd-soc- + # BCM63XX Platform Support + snd-soc-63xx-objs := bcm63xx-i2s-whistler.o bcm63xx-pcm-whistler.o + +-obj-$(CONFIG_SND_BCM63XX_I2S_WHISTLER) += snd-soc-63xx.o +\ No newline at end of file ++obj-$(CONFIG_SND_BCM63XX_I2S_WHISTLER) += snd-soc-63xx.o ++ ++# Google voiceHAT custom codec support ++snd-soc-googlevoicehat-codec-objs := googlevoicehat-codec.o ++ ++# BCM2708 Machine Support ++snd-soc-hifiberry-dacplus-objs := hifiberry_dacplus.o ++snd-soc-hifiberry-dacplushd-objs := hifiberry_dacplushd.o ++snd-soc-hifiberry-dacplusadc-objs := hifiberry_dacplusadc.o ++snd-soc-hifiberry-dacplusadcpro-objs := hifiberry_dacplusadcpro.o ++snd-soc-hifiberry-dacplusdsp-objs := hifiberry_dacplusdsp.o ++snd-soc-justboom-both-objs := justboom-both.o ++snd-soc-justboom-dac-objs := justboom-dac.o ++snd-soc-rpi-cirrus-objs := rpi-cirrus.o ++snd-soc-rpi-proto-objs := rpi-proto.o ++snd-soc-iqaudio-codec-objs := iqaudio-codec.o ++snd-soc-iqaudio-dac-objs := iqaudio-dac.o ++ snd-soc-i-sabre-q2m-objs := i-sabre-q2m.o ++snd-soc-audioinjector-pi-soundcard-objs := audioinjector-pi-soundcard.o ++snd-soc-audioinjector-octo-soundcard-objs := audioinjector-octo-soundcard.o ++snd-soc-audioinjector-isolated-soundcard-objs := audioinjector-isolated-soundcard.o ++snd-soc-audiosense-pi-objs := audiosense-pi.o ++snd-soc-digidac1-soundcard-objs := digidac1-soundcard.o ++snd-soc-dionaudio-loco-objs := dionaudio_loco.o ++snd-soc-dionaudio-loco-v2-objs := dionaudio_loco-v2.o ++snd-soc-allo-boss-dac-objs := allo-boss-dac.o ++snd-soc-allo-piano-dac-objs := allo-piano-dac.o ++snd-soc-allo-piano-dac-plus-objs := allo-piano-dac-plus.o ++snd-soc-allo-katana-codec-objs := allo-katana-codec.o ++snd-soc-pisound-objs := pisound.o ++snd-soc-fe-pi-audio-objs := fe-pi-audio.o ++snd-soc-rpi-simple-soundcard-objs := rpi-simple-soundcard.o ++snd-soc-rpi-wm8804-soundcard-objs := rpi-wm8804-soundcard.o ++ ++obj-$(CONFIG_SND_BCM2708_SOC_GOOGLEVOICEHAT_SOUNDCARD) += snd-soc-googlevoicehat-codec.o ++obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUS) += snd-soc-hifiberry-dacplus.o ++obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUSHD) += snd-soc-hifiberry-dacplushd.o ++obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUSADC) += snd-soc-hifiberry-dacplusadc.o ++obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUSADCPRO) += snd-soc-hifiberry-dacplusadcpro.o ++obj-$(CONFIG_SND_BCM2708_SOC_HIFIBERRY_DACPLUSDSP) += snd-soc-hifiberry-dacplusdsp.o ++obj-$(CONFIG_SND_BCM2708_SOC_JUSTBOOM_BOTH) += snd-soc-justboom-both.o ++obj-$(CONFIG_SND_BCM2708_SOC_JUSTBOOM_DAC) += snd-soc-justboom-dac.o ++obj-$(CONFIG_SND_BCM2708_SOC_RPI_CIRRUS) += snd-soc-rpi-cirrus.o ++obj-$(CONFIG_SND_BCM2708_SOC_RPI_PROTO) += snd-soc-rpi-proto.o ++obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_CODEC) += snd-soc-iqaudio-codec.o ++obj-$(CONFIG_SND_BCM2708_SOC_IQAUDIO_DAC) += snd-soc-iqaudio-dac.o ++obj-$(CONFIG_SND_BCM2708_SOC_I_SABRE_Q2M) += snd-soc-i-sabre-q2m.o ++obj-$(CONFIG_SND_AUDIOINJECTOR_PI_SOUNDCARD) += snd-soc-audioinjector-pi-soundcard.o ++obj-$(CONFIG_SND_AUDIOINJECTOR_OCTO_SOUNDCARD) += snd-soc-audioinjector-octo-soundcard.o ++obj-$(CONFIG_SND_AUDIOINJECTOR_ISOLATED_SOUNDCARD) += snd-soc-audioinjector-isolated-soundcard.o ++obj-$(CONFIG_SND_AUDIOSENSE_PI) += snd-soc-audiosense-pi.o ++obj-$(CONFIG_SND_DIGIDAC1_SOUNDCARD) += snd-soc-digidac1-soundcard.o ++obj-$(CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO) += snd-soc-dionaudio-loco.o ++obj-$(CONFIG_SND_BCM2708_SOC_DIONAUDIO_LOCO_V2) += snd-soc-dionaudio-loco-v2.o ++obj-$(CONFIG_SND_BCM2708_SOC_ALLO_BOSS_DAC) += snd-soc-allo-boss-dac.o ++obj-$(CONFIG_SND_BCM2708_SOC_ALLO_PIANO_DAC) += snd-soc-allo-piano-dac.o ++obj-$(CONFIG_SND_BCM2708_SOC_ALLO_PIANO_DAC_PLUS) += snd-soc-allo-piano-dac-plus.o ++obj-$(CONFIG_SND_BCM2708_SOC_ALLO_KATANA_DAC) += snd-soc-allo-katana-codec.o ++obj-$(CONFIG_SND_PISOUND) += snd-soc-pisound.o ++obj-$(CONFIG_SND_BCM2708_SOC_FE_PI_AUDIO) += snd-soc-fe-pi-audio.o ++obj-$(CONFIG_SND_RPI_SIMPLE_SOUNDCARD) += snd-soc-rpi-simple-soundcard.o ++obj-$(CONFIG_SND_RPI_WM8804_SOUNDCARD) += snd-soc-rpi-wm8804-soundcard.o +--- /dev/null ++++ b/sound/soc/bcm/allo-boss-dac.c +@@ -0,0 +1,456 @@ ++/* ++ * ALSA ASoC Machine Driver for Allo Boss DAC ++ * ++ * Author: Baswaraj K ++ * Copyright 2017 ++ * based on code by Daniel Matuschek, ++ * Stuart MacLean ++ * based on code by Florian Meier ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include "../codecs/pcm512x.h" ++ ++#define ALLO_BOSS_NOCLOCK 0 ++#define ALLO_BOSS_CLK44EN 1 ++#define ALLO_BOSS_CLK48EN 2 ++ ++struct pcm512x_priv { ++ struct regmap *regmap; ++ struct clk *sclk; ++}; ++ ++static struct gpio_desc *mute_gpio; ++ ++/* Clock rate of CLK44EN attached to GPIO6 pin */ ++#define CLK_44EN_RATE 45158400UL ++/* Clock rate of CLK48EN attached to GPIO3 pin */ ++#define CLK_48EN_RATE 49152000UL ++ ++static bool slave; ++static bool snd_soc_allo_boss_master; ++static bool digital_gain_0db_limit = true; ++ ++static void snd_allo_boss_select_clk(struct snd_soc_component *component, ++ int clk_id) ++{ ++ switch (clk_id) { ++ case ALLO_BOSS_NOCLOCK: ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x24, 0x00); ++ break; ++ case ALLO_BOSS_CLK44EN: ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x24, 0x20); ++ break; ++ case ALLO_BOSS_CLK48EN: ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x24, 0x04); ++ break; ++ } ++} ++ ++static void snd_allo_boss_clk_gpio(struct snd_soc_component *component) ++{ ++ snd_soc_component_update_bits(component, PCM512x_GPIO_EN, 0x24, 0x24); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_OUTPUT_3, 0x0f, 0x02); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_OUTPUT_6, 0x0f, 0x02); ++} ++ ++static bool snd_allo_boss_is_sclk(struct snd_soc_component *component) ++{ ++ unsigned int sck; ++ ++ sck = snd_soc_component_read(component, PCM512x_RATE_DET_4); ++ return (!(sck & 0x40)); ++} ++ ++static bool snd_allo_boss_is_sclk_sleep( ++ struct snd_soc_component *component) ++{ ++ msleep(2); ++ return snd_allo_boss_is_sclk(component); ++} ++ ++static bool snd_allo_boss_is_master_card(struct snd_soc_component *component) ++{ ++ bool isClk44EN, isClk48En, isNoClk; ++ ++ snd_allo_boss_clk_gpio(component); ++ ++ snd_allo_boss_select_clk(component, ALLO_BOSS_CLK44EN); ++ isClk44EN = snd_allo_boss_is_sclk_sleep(component); ++ ++ snd_allo_boss_select_clk(component, ALLO_BOSS_NOCLOCK); ++ isNoClk = snd_allo_boss_is_sclk_sleep(component); ++ ++ snd_allo_boss_select_clk(component, ALLO_BOSS_CLK48EN); ++ isClk48En = snd_allo_boss_is_sclk_sleep(component); ++ ++ return (isClk44EN && isClk48En && !isNoClk); ++} ++ ++static int snd_allo_boss_clk_for_rate(int sample_rate) ++{ ++ int type; ++ ++ switch (sample_rate) { ++ case 11025: ++ case 22050: ++ case 44100: ++ case 88200: ++ case 176400: ++ case 352800: ++ type = ALLO_BOSS_CLK44EN; ++ break; ++ default: ++ type = ALLO_BOSS_CLK48EN; ++ break; ++ } ++ return type; ++} ++ ++static void snd_allo_boss_set_sclk(struct snd_soc_component *component, ++ int sample_rate) ++{ ++ struct pcm512x_priv *pcm512x = snd_soc_component_get_drvdata(component); ++ ++ if (!IS_ERR(pcm512x->sclk)) { ++ int ctype; ++ ++ ctype = snd_allo_boss_clk_for_rate(sample_rate); ++ clk_set_rate(pcm512x->sclk, (ctype == ALLO_BOSS_CLK44EN) ++ ? CLK_44EN_RATE : CLK_48EN_RATE); ++ snd_allo_boss_select_clk(component, ctype); ++ } ++} ++ ++static int snd_allo_boss_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ struct pcm512x_priv *priv = snd_soc_component_get_drvdata(component); ++ ++ if (slave) ++ snd_soc_allo_boss_master = false; ++ else ++ snd_soc_allo_boss_master = ++ snd_allo_boss_is_master_card(component); ++ ++ if (snd_soc_allo_boss_master) { ++ struct snd_soc_dai_link *dai = rtd->dai_link; ++ ++ dai->name = "BossDAC"; ++ dai->stream_name = "Boss DAC HiFi [Master]"; ++ dai->dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF ++ | SND_SOC_DAIFMT_CBM_CFM; ++ ++ snd_soc_component_update_bits(component, PCM512x_BCLK_LRCLK_CFG, 0x31, 0x11); ++ snd_soc_component_update_bits(component, PCM512x_MASTER_MODE, 0x03, 0x03); ++ snd_soc_component_update_bits(component, PCM512x_MASTER_CLKDIV_2, 0x7f, 63); ++ /* ++ * Default sclk to CLK_48EN_RATE, otherwise codec ++ * pcm512x_dai_startup_master method could call ++ * snd_pcm_hw_constraint_ratnums using CLK_44EN/64 ++ * which will mask 384k sample rate. ++ */ ++ if (!IS_ERR(priv->sclk)) ++ clk_set_rate(priv->sclk, CLK_48EN_RATE); ++ } else { ++ priv->sclk = ERR_PTR(-ENOENT); ++ } ++ ++ snd_soc_component_update_bits(component, PCM512x_GPIO_EN, 0x08, 0x08); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_OUTPUT_4, 0x0f, 0x02); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x08, 0x08); ++ ++ if (digital_gain_0db_limit) { ++ int ret; ++ struct snd_soc_card *card = rtd->card; ++ ++ ret = snd_soc_limit_volume(card, "Digital Playback Volume", ++ 207); ++ if (ret < 0) ++ dev_warn(card->dev, "Failed to set volume limit: %d\n", ++ ret); ++ } ++ ++ return 0; ++} ++ ++static int snd_allo_boss_update_rate_den( ++ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ struct pcm512x_priv *pcm512x = snd_soc_component_get_drvdata(component); ++ struct snd_ratnum *rats_no_pll; ++ unsigned int num = 0, den = 0; ++ int err; ++ ++ rats_no_pll = devm_kzalloc(rtd->dev, sizeof(*rats_no_pll), GFP_KERNEL); ++ if (!rats_no_pll) ++ return -ENOMEM; ++ ++ rats_no_pll->num = clk_get_rate(pcm512x->sclk) / 64; ++ rats_no_pll->den_min = 1; ++ rats_no_pll->den_max = 128; ++ rats_no_pll->den_step = 1; ++ ++ err = snd_interval_ratnum(hw_param_interval(params, ++ SNDRV_PCM_HW_PARAM_RATE), 1, rats_no_pll, &num, &den); ++ if (err >= 0 && den) { ++ params->rate_num = num; ++ params->rate_den = den; ++ } ++ ++ devm_kfree(rtd->dev, rats_no_pll); ++ return 0; ++} ++ ++static void snd_allo_boss_gpio_mute(struct snd_soc_card *card) ++{ ++ if (mute_gpio) ++ gpiod_set_value_cansleep(mute_gpio, 1); ++} ++ ++static void snd_allo_boss_gpio_unmute(struct snd_soc_card *card) ++{ ++ if (mute_gpio) ++ gpiod_set_value_cansleep(mute_gpio, 0); ++} ++ ++static int snd_allo_boss_set_bias_level(struct snd_soc_card *card, ++ struct snd_soc_dapm_context *dapm, enum snd_soc_bias_level level) ++{ ++ struct snd_soc_pcm_runtime *rtd; ++ struct snd_soc_dai *codec_dai; ++ ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ codec_dai = asoc_rtd_to_codec(rtd, 0); ++ ++ if (dapm->dev != codec_dai->dev) ++ return 0; ++ ++ switch (level) { ++ case SND_SOC_BIAS_PREPARE: ++ if (dapm->bias_level != SND_SOC_BIAS_STANDBY) ++ break; ++ /* UNMUTE DAC */ ++ snd_allo_boss_gpio_unmute(card); ++ break; ++ ++ case SND_SOC_BIAS_STANDBY: ++ if (dapm->bias_level != SND_SOC_BIAS_PREPARE) ++ break; ++ /* MUTE DAC */ ++ snd_allo_boss_gpio_mute(card); ++ break; ++ ++ default: ++ break; ++ } ++ ++ return 0; ++} ++ ++static int snd_allo_boss_hw_params( ++ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params) ++{ ++ int ret = 0; ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ int channels = params_channels(params); ++ int width = snd_pcm_format_physical_width(params_format(params)); ++ ++ if (snd_soc_allo_boss_master) { ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ ++ snd_allo_boss_set_sclk(component, ++ params_rate(params)); ++ ++ ret = snd_allo_boss_update_rate_den( ++ substream, params); ++ if (ret) ++ return ret; ++ } ++ ++ ret = snd_soc_dai_set_bclk_ratio(asoc_rtd_to_cpu(rtd, 0), channels * width); ++ if (ret) ++ return ret; ++ ret = snd_soc_dai_set_bclk_ratio(asoc_rtd_to_codec(rtd, 0), channels * width); ++ return ret; ++} ++ ++static int snd_allo_boss_startup( ++ struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_card *card = rtd->card; ++ ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x08, 0x08); ++ snd_allo_boss_gpio_mute(card); ++ ++ if (snd_soc_allo_boss_master) { ++ struct pcm512x_priv *priv = snd_soc_component_get_drvdata(component); ++ /* ++ * Default sclk to CLK_48EN_RATE, otherwise codec ++ * pcm512x_dai_startup_master method could call ++ * snd_pcm_hw_constraint_ratnums using CLK_44EN/64 ++ * which will mask 384k sample rate. ++ */ ++ if (!IS_ERR(priv->sclk)) ++ clk_set_rate(priv->sclk, CLK_48EN_RATE); ++ } ++ ++ return 0; ++} ++ ++static void snd_allo_boss_shutdown( ++ struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x08, 0x00); ++} ++ ++static int snd_allo_boss_prepare( ++ struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_card *card = rtd->card; ++ ++ snd_allo_boss_gpio_unmute(card); ++ return 0; ++} ++/* machine stream operations */ ++static struct snd_soc_ops snd_allo_boss_ops = { ++ .hw_params = snd_allo_boss_hw_params, ++ .startup = snd_allo_boss_startup, ++ .shutdown = snd_allo_boss_shutdown, ++ .prepare = snd_allo_boss_prepare, ++}; ++ ++SND_SOC_DAILINK_DEFS(allo_boss, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("pcm512x.1-004d", "pcm512x-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_allo_boss_dai[] = { ++{ ++ .name = "Boss DAC", ++ .stream_name = "Boss DAC HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | ++ SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ .ops = &snd_allo_boss_ops, ++ .init = snd_allo_boss_init, ++ SND_SOC_DAILINK_REG(allo_boss), ++}, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_allo_boss = { ++ .name = "BossDAC", ++ .owner = THIS_MODULE, ++ .dai_link = snd_allo_boss_dai, ++ .num_links = ARRAY_SIZE(snd_allo_boss_dai), ++}; ++ ++static int snd_allo_boss_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ ++ snd_allo_boss.dev = &pdev->dev; ++ ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai; ++ ++ dai = &snd_allo_boss_dai[0]; ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ ++ if (i2s_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } ++ ++ digital_gain_0db_limit = !of_property_read_bool( ++ pdev->dev.of_node, "allo,24db_digital_gain"); ++ slave = of_property_read_bool(pdev->dev.of_node, ++ "allo,slave"); ++ ++ mute_gpio = devm_gpiod_get_optional(&pdev->dev, "mute", ++ GPIOD_OUT_LOW); ++ if (IS_ERR(mute_gpio)) { ++ ret = PTR_ERR(mute_gpio); ++ dev_err(&pdev->dev, ++ "failed to get mute gpio: %d\n", ret); ++ return ret; ++ } ++ ++ if (mute_gpio) ++ snd_allo_boss.set_bias_level = ++ snd_allo_boss_set_bias_level; ++ ++ ret = snd_soc_register_card(&snd_allo_boss); ++ if (ret) { ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ return ret; ++ } ++ ++ if (mute_gpio) ++ snd_allo_boss_gpio_mute(&snd_allo_boss); ++ ++ return 0; ++ } ++ ++ return -EINVAL; ++} ++ ++static int snd_allo_boss_remove(struct platform_device *pdev) ++{ ++ snd_allo_boss_gpio_mute(&snd_allo_boss); ++ return snd_soc_unregister_card(&snd_allo_boss); ++} ++ ++static const struct of_device_id snd_allo_boss_of_match[] = { ++ { .compatible = "allo,boss-dac", }, ++ { /* sentinel */ }, ++}; ++MODULE_DEVICE_TABLE(of, snd_allo_boss_of_match); ++ ++static struct platform_driver snd_allo_boss_driver = { ++ .driver = { ++ .name = "snd-allo-boss-dac", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_allo_boss_of_match, ++ }, ++ .probe = snd_allo_boss_probe, ++ .remove = snd_allo_boss_remove, ++}; ++ ++module_platform_driver(snd_allo_boss_driver); ++ ++MODULE_AUTHOR("Baswaraj K "); ++MODULE_DESCRIPTION("ALSA ASoC Machine Driver for Allo Boss DAC"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/allo-katana-codec.c +@@ -0,0 +1,388 @@ ++/* ++ * Driver for the ALLO KATANA CODEC ++ * ++ * Author: Jaikumar ++ * Copyright 2018 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++ ++#define KATANA_CODEC_CHIP_ID 0x30 ++#define KATANA_CODEC_VIRT_BASE 0x100 ++#define KATANA_CODEC_PAGE 0 ++ ++#define KATANA_CODEC_CHIP_ID_REG (KATANA_CODEC_VIRT_BASE + 0) ++#define KATANA_CODEC_RESET (KATANA_CODEC_VIRT_BASE + 1) ++#define KATANA_CODEC_VOLUME_1 (KATANA_CODEC_VIRT_BASE + 2) ++#define KATANA_CODEC_VOLUME_2 (KATANA_CODEC_VIRT_BASE + 3) ++#define KATANA_CODEC_MUTE (KATANA_CODEC_VIRT_BASE + 4) ++#define KATANA_CODEC_DSP_PROGRAM (KATANA_CODEC_VIRT_BASE + 5) ++#define KATANA_CODEC_DEEMPHASIS (KATANA_CODEC_VIRT_BASE + 6) ++#define KATANA_CODEC_DOP (KATANA_CODEC_VIRT_BASE + 7) ++#define KATANA_CODEC_FORMAT (KATANA_CODEC_VIRT_BASE + 8) ++#define KATANA_CODEC_COMMAND (KATANA_CODEC_VIRT_BASE + 9) ++#define KATANA_CODEC_MUTE_STREAM (KATANA_CODEC_VIRT_BASE + 10) ++ ++#define KATANA_CODEC_MAX_REGISTER (KATANA_CODEC_VIRT_BASE + 10) ++ ++#define KATANA_CODEC_FMT 0xff ++#define KATANA_CODEC_CHAN_MONO 0x00 ++#define KATANA_CODEC_CHAN_STEREO 0x80 ++#define KATANA_CODEC_ALEN_16 0x10 ++#define KATANA_CODEC_ALEN_24 0x20 ++#define KATANA_CODEC_ALEN_32 0x30 ++#define KATANA_CODEC_RATE_11025 0x01 ++#define KATANA_CODEC_RATE_22050 0x02 ++#define KATANA_CODEC_RATE_32000 0x03 ++#define KATANA_CODEC_RATE_44100 0x04 ++#define KATANA_CODEC_RATE_48000 0x05 ++#define KATANA_CODEC_RATE_88200 0x06 ++#define KATANA_CODEC_RATE_96000 0x07 ++#define KATANA_CODEC_RATE_176400 0x08 ++#define KATANA_CODEC_RATE_192000 0x09 ++#define KATANA_CODEC_RATE_352800 0x0a ++#define KATANA_CODEC_RATE_384000 0x0b ++ ++ ++struct katana_codec_priv { ++ struct regmap *regmap; ++ int fmt; ++}; ++ ++static const struct reg_default katana_codec_reg_defaults[] = { ++ { KATANA_CODEC_RESET, 0x00 }, ++ { KATANA_CODEC_VOLUME_1, 0xF0 }, ++ { KATANA_CODEC_VOLUME_2, 0xF0 }, ++ { KATANA_CODEC_MUTE, 0x00 }, ++ { KATANA_CODEC_DSP_PROGRAM, 0x04 }, ++ { KATANA_CODEC_DEEMPHASIS, 0x00 }, ++ { KATANA_CODEC_DOP, 0x00 }, ++ { KATANA_CODEC_FORMAT, 0xb4 }, ++}; ++ ++static const char * const katana_codec_dsp_program_texts[] = { ++ "Linear Phase Fast Roll-off Filter", ++ "Linear Phase Slow Roll-off Filter", ++ "Minimum Phase Fast Roll-off Filter", ++ "Minimum Phase Slow Roll-off Filter", ++ "Apodizing Fast Roll-off Filter", ++ "Corrected Minimum Phase Fast Roll-off Filter", ++ "Brick Wall Filter", ++}; ++ ++static const unsigned int katana_codec_dsp_program_values[] = { ++ 0, ++ 1, ++ 2, ++ 3, ++ 4, ++ 6, ++ 7, ++}; ++ ++static SOC_VALUE_ENUM_SINGLE_DECL(katana_codec_dsp_program, ++ KATANA_CODEC_DSP_PROGRAM, 0, 0x07, ++ katana_codec_dsp_program_texts, ++ katana_codec_dsp_program_values); ++ ++static const char * const katana_codec_deemphasis_texts[] = { ++ "Bypass", ++ "32kHz", ++ "44.1kHz", ++ "48kHz", ++}; ++ ++static const unsigned int katana_codec_deemphasis_values[] = { ++ 0, ++ 1, ++ 2, ++ 3, ++}; ++ ++static SOC_VALUE_ENUM_SINGLE_DECL(katana_codec_deemphasis, ++ KATANA_CODEC_DEEMPHASIS, 0, 0x03, ++ katana_codec_deemphasis_texts, ++ katana_codec_deemphasis_values); ++ ++static const SNDRV_CTL_TLVD_DECLARE_DB_MINMAX(master_tlv, -12750, 0); ++ ++static const struct snd_kcontrol_new katana_codec_controls[] = { ++ SOC_DOUBLE_R_TLV("Master Playback Volume", KATANA_CODEC_VOLUME_1, ++ KATANA_CODEC_VOLUME_2, 0, 255, 1, master_tlv), ++ SOC_DOUBLE("Master Playback Switch", KATANA_CODEC_MUTE, 0, 0, 1, 1), ++ SOC_ENUM("DSP Program Route", katana_codec_dsp_program), ++ SOC_ENUM("Deemphasis Route", katana_codec_deemphasis), ++ SOC_SINGLE("DoP Playback Switch", KATANA_CODEC_DOP, 0, 1, 1) ++}; ++ ++static bool katana_codec_readable_register(struct device *dev, ++ unsigned int reg) ++{ ++ switch (reg) { ++ case KATANA_CODEC_CHIP_ID_REG: ++ return true; ++ default: ++ return reg < 0xff; ++ } ++} ++ ++static int katana_codec_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params, ++ struct snd_soc_dai *dai) ++{ ++ struct snd_soc_component *component = dai->component; ++ struct katana_codec_priv *katana_codec = ++ snd_soc_component_get_drvdata(component); ++ int fmt = 0; ++ int ret; ++ ++ dev_dbg(component->card->dev, "hw_params %u Hz, %u channels, %u bits\n", ++ params_rate(params), ++ params_channels(params), ++ params_width(params)); ++ ++ switch (katana_codec->fmt & SND_SOC_DAIFMT_MASTER_MASK) { ++ case SND_SOC_DAIFMT_CBM_CFM: // master ++ if (params_channels(params) == 2) ++ fmt = KATANA_CODEC_CHAN_STEREO; ++ else ++ fmt = KATANA_CODEC_CHAN_MONO; ++ ++ switch (params_width(params)) { ++ case 16: ++ fmt |= KATANA_CODEC_ALEN_16; ++ break; ++ case 24: ++ fmt |= KATANA_CODEC_ALEN_24; ++ break; ++ case 32: ++ fmt |= KATANA_CODEC_ALEN_32; ++ break; ++ default: ++ dev_err(component->card->dev, "Bad frame size: %d\n", ++ params_width(params)); ++ return -EINVAL; ++ } ++ ++ switch (params_rate(params)) { ++ case 44100: ++ fmt |= KATANA_CODEC_RATE_44100; ++ break; ++ case 48000: ++ fmt |= KATANA_CODEC_RATE_48000; ++ break; ++ case 88200: ++ fmt |= KATANA_CODEC_RATE_88200; ++ break; ++ case 96000: ++ fmt |= KATANA_CODEC_RATE_96000; ++ break; ++ case 176400: ++ fmt |= KATANA_CODEC_RATE_176400; ++ break; ++ case 192000: ++ fmt |= KATANA_CODEC_RATE_192000; ++ break; ++ case 352800: ++ fmt |= KATANA_CODEC_RATE_352800; ++ break; ++ case 384000: ++ fmt |= KATANA_CODEC_RATE_384000; ++ break; ++ default: ++ dev_err(component->card->dev, "Bad sample rate: %d\n", ++ params_rate(params)); ++ return -EINVAL; ++ } ++ ++ ret = regmap_write(katana_codec->regmap, KATANA_CODEC_FORMAT, ++ fmt); ++ if (ret != 0) { ++ dev_err(component->card->dev, "Failed to set format: %d\n", ret); ++ return ret; ++ } ++ break; ++ ++ case SND_SOC_DAIFMT_CBS_CFS: ++ break; ++ ++ default: ++ return -EINVAL; ++ } ++ ++ return 0; ++} ++ ++static int katana_codec_set_fmt(struct snd_soc_dai *dai, unsigned int fmt) ++{ ++ struct snd_soc_component *component = dai->component; ++ struct katana_codec_priv *katana_codec = ++ snd_soc_component_get_drvdata(component); ++ ++ katana_codec->fmt = fmt; ++ ++ return 0; ++} ++ ++int katana_codec_dai_mute_stream(struct snd_soc_dai *dai, int mute, ++ int stream) ++{ ++ struct snd_soc_component *component = dai->component; ++ struct katana_codec_priv *katana_codec = ++ snd_soc_component_get_drvdata(component); ++ int ret = 0; ++ ++ ret = regmap_write(katana_codec->regmap, KATANA_CODEC_MUTE_STREAM, ++ mute); ++ if (ret != 0) { ++ dev_err(component->card->dev, "Failed to set mute: %d\n", ret); ++ return ret; ++ } ++ return ret; ++} ++ ++static const struct snd_soc_dai_ops katana_codec_dai_ops = { ++ .mute_stream = katana_codec_dai_mute_stream, ++ .hw_params = katana_codec_hw_params, ++ .set_fmt = katana_codec_set_fmt, ++}; ++ ++static struct snd_soc_dai_driver katana_codec_dai = { ++ .name = "allo-katana-codec", ++ .playback = { ++ .stream_name = "Playback", ++ .channels_min = 2, ++ .channels_max = 2, ++ .rates = SNDRV_PCM_RATE_CONTINUOUS, ++ .rate_min = 44100, ++ .rate_max = 384000, ++ .formats = SNDRV_PCM_FMTBIT_S16_LE | ++ SNDRV_PCM_FMTBIT_S32_LE ++ }, ++ .ops = &katana_codec_dai_ops, ++}; ++ ++static struct snd_soc_component_driver katana_codec_component_driver = { ++ .idle_bias_on = true, ++ ++ .controls = katana_codec_controls, ++ .num_controls = ARRAY_SIZE(katana_codec_controls), ++}; ++ ++static const struct regmap_range_cfg katana_codec_range = { ++ .name = "Pages", .range_min = KATANA_CODEC_VIRT_BASE, ++ .range_max = KATANA_CODEC_MAX_REGISTER, ++ .selector_reg = KATANA_CODEC_PAGE, ++ .selector_mask = 0xff, ++ .window_start = 0, .window_len = 0x100, ++}; ++ ++const struct regmap_config katana_codec_regmap = { ++ .reg_bits = 8, ++ .val_bits = 8, ++ ++ .ranges = &katana_codec_range, ++ .num_ranges = 1, ++ ++ .max_register = KATANA_CODEC_MAX_REGISTER, ++ .readable_reg = katana_codec_readable_register, ++ .reg_defaults = katana_codec_reg_defaults, ++ .num_reg_defaults = ARRAY_SIZE(katana_codec_reg_defaults), ++ .cache_type = REGCACHE_RBTREE, ++}; ++ ++static int allo_katana_component_probe(struct i2c_client *i2c, ++ const struct i2c_device_id *id) ++{ ++ struct regmap *regmap; ++ struct regmap_config config = katana_codec_regmap; ++ struct device *dev = &i2c->dev; ++ struct katana_codec_priv *katana_codec; ++ unsigned int chip_id = 0; ++ int ret; ++ ++ regmap = devm_regmap_init_i2c(i2c, &config); ++ if (IS_ERR(regmap)) ++ return PTR_ERR(regmap); ++ ++ katana_codec = devm_kzalloc(dev, sizeof(struct katana_codec_priv), ++ GFP_KERNEL); ++ if (!katana_codec) ++ return -ENOMEM; ++ ++ dev_set_drvdata(dev, katana_codec); ++ katana_codec->regmap = regmap; ++ ++ ret = regmap_read(regmap, KATANA_CODEC_CHIP_ID_REG, &chip_id); ++ if ((ret != 0) || (chip_id != KATANA_CODEC_CHIP_ID)) { ++ dev_err(dev, "Failed to read Chip or wrong Chip id: %d\n", ret); ++ return ret; ++ } ++ regmap_update_bits(regmap, KATANA_CODEC_RESET, 0x01, 0x01); ++ msleep(10); ++ ++ ret = snd_soc_register_component(dev, &katana_codec_component_driver, ++ &katana_codec_dai, 1); ++ if (ret != 0) { ++ dev_err(dev, "failed to register codec: %d\n", ret); ++ return ret; ++ } ++ ++ return 0; ++} ++ ++static int allo_katana_component_remove(struct i2c_client *i2c) ++{ ++ snd_soc_unregister_component(&i2c->dev); ++ return 0; ++} ++ ++static const struct i2c_device_id allo_katana_component_id[] = { ++ { "allo-katana-codec", }, ++ { } ++}; ++MODULE_DEVICE_TABLE(i2c, allo_katana_component_id); ++ ++static const struct of_device_id allo_katana_codec_of_match[] = { ++ { .compatible = "allo,allo-katana-codec", }, ++ { } ++}; ++MODULE_DEVICE_TABLE(of, allo_katana_codec_of_match); ++ ++static struct i2c_driver allo_katana_component_driver = { ++ .probe = allo_katana_component_probe, ++ .remove = allo_katana_component_remove, ++ .id_table = allo_katana_component_id, ++ .driver = { ++ .name = "allo-katana-codec", ++ .of_match_table = allo_katana_codec_of_match, ++ }, ++}; ++ ++module_i2c_driver(allo_katana_component_driver); ++ ++MODULE_DESCRIPTION("ASoC Allo Katana Codec Driver"); ++MODULE_AUTHOR("Jaikumar "); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/allo-piano-dac-plus.c +@@ -0,0 +1,987 @@ ++/* ++ * ALSA ASoC Machine Driver for Allo Piano DAC Plus Subwoofer ++ * ++ * Author: Baswaraj K ++ * Copyright 2016 ++ * based on code by Daniel Matuschek ++ * based on code by Florian Meier ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include "../codecs/pcm512x.h" ++ ++#define P_DAC_LEFT_MUTE 0x10 ++#define P_DAC_RIGHT_MUTE 0x01 ++#define P_DAC_MUTE 0x11 ++#define P_DAC_UNMUTE 0x00 ++#define P_MUTE 1 ++#define P_UNMUTE 0 ++ ++struct dsp_code { ++ char i2c_addr; ++ char offset; ++ char val; ++}; ++ ++struct glb_pool { ++ struct mutex lock; ++ unsigned int dual_mode; ++ unsigned int set_lowpass; ++ unsigned int set_mode; ++ unsigned int set_rate; ++ unsigned int dsp_page_number; ++}; ++ ++static bool digital_gain_0db_limit = true; ++bool glb_mclk; ++ ++static struct gpio_desc *mute_gpio[2]; ++ ++static const char * const allo_piano_mode_texts[] = { ++ "None", ++ "2.0", ++ "2.1", ++ "2.2", ++}; ++ ++static const SOC_ENUM_SINGLE_DECL(allo_piano_mode_enum, ++ 0, 0, allo_piano_mode_texts); ++ ++static const char * const allo_piano_dual_mode_texts[] = { ++ "None", ++ "Dual-Mono", ++ "Dual-Stereo", ++}; ++ ++static const SOC_ENUM_SINGLE_DECL(allo_piano_dual_mode_enum, ++ 0, 0, allo_piano_dual_mode_texts); ++ ++static const char * const allo_piano_dsp_low_pass_texts[] = { ++ "60", ++ "70", ++ "80", ++ "90", ++ "100", ++ "110", ++ "120", ++ "130", ++ "140", ++ "150", ++ "160", ++ "170", ++ "180", ++ "190", ++ "200", ++}; ++ ++static const SOC_ENUM_SINGLE_DECL(allo_piano_enum, ++ 0, 0, allo_piano_dsp_low_pass_texts); ++ ++static int __snd_allo_piano_dsp_program(struct snd_soc_pcm_runtime *rtd, ++ unsigned int mode, unsigned int rate, unsigned int lowpass) ++{ ++ const struct firmware *fw; ++ struct snd_soc_card *card = rtd->card; ++ struct glb_pool *glb_ptr = card->drvdata; ++ char firmware_name[60]; ++ int ret = 0, dac = 0; ++ ++ if (rate <= 46000) ++ rate = 44100; ++ else if (rate <= 68000) ++ rate = 48000; ++ else if (rate <= 92000) ++ rate = 88200; ++ else if (rate <= 136000) ++ rate = 96000; ++ else if (rate <= 184000) ++ rate = 176400; ++ else ++ rate = 192000; ++ ++ if (lowpass > 14) ++ glb_ptr->set_lowpass = lowpass = 0; ++ ++ if (mode > 3) ++ glb_ptr->set_mode = mode = 0; ++ ++ if (mode > 0) ++ glb_ptr->dual_mode = 0; ++ ++ /* same configuration loaded */ ++ if ((rate == glb_ptr->set_rate) && (lowpass == glb_ptr->set_lowpass) ++ && (mode == glb_ptr->set_mode)) ++ return 0; ++ ++ switch (mode) { ++ case 0: /* None */ ++ return 1; ++ ++ case 1: /* 2.0 */ ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 0)->component, ++ PCM512x_MUTE, P_DAC_UNMUTE); ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_MUTE, P_DAC_MUTE); ++ glb_ptr->set_rate = rate; ++ glb_ptr->set_mode = mode; ++ glb_ptr->set_lowpass = lowpass; ++ return 1; ++ ++ default: ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 0)->component, ++ PCM512x_MUTE, P_DAC_UNMUTE); ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_MUTE, P_DAC_UNMUTE); ++ } ++ ++ for (dac = 0; dac < rtd->num_codecs; dac++) { ++ struct dsp_code *dsp_code_read; ++ int i = 1; ++ ++ if (dac == 0) { /* high */ ++ snprintf(firmware_name, sizeof(firmware_name), ++ "allo/piano/2.2/allo-piano-dsp-%d-%d-%d.bin", ++ rate, ((lowpass * 10) + 60), dac); ++ } else { /* low */ ++ snprintf(firmware_name, sizeof(firmware_name), ++ "allo/piano/2.%d/allo-piano-dsp-%d-%d-%d.bin", ++ (mode - 1), rate, ((lowpass * 10) + 60), dac); ++ } ++ ++ dev_info(rtd->card->dev, "Dsp Firmware File Name: %s\n", ++ firmware_name); ++ ++ ret = request_firmware(&fw, firmware_name, rtd->card->dev); ++ if (ret < 0) { ++ dev_err(rtd->card->dev, ++ "Error: Allo Piano Firmware %s missing. %d\n", ++ firmware_name, ret); ++ goto err; ++ } ++ ++ while (i < (fw->size - 1)) { ++ dsp_code_read = (struct dsp_code *)&fw->data[i]; ++ ++ if (dsp_code_read->offset == 0) { ++ glb_ptr->dsp_page_number = dsp_code_read->val; ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, dac)->component, ++ PCM512x_PAGE_BASE(0), ++ dsp_code_read->val); ++ ++ } else if (dsp_code_read->offset != 0) { ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, dac)->component, ++ (PCM512x_PAGE_BASE( ++ glb_ptr->dsp_page_number) + ++ dsp_code_read->offset), ++ dsp_code_read->val); ++ } ++ if (ret < 0) { ++ dev_err(rtd->card->dev, ++ "Failed to write Register: %d\n", ret); ++ release_firmware(fw); ++ goto err; ++ } ++ i = i + 3; ++ } ++ release_firmware(fw); ++ } ++ glb_ptr->set_rate = rate; ++ glb_ptr->set_mode = mode; ++ glb_ptr->set_lowpass = lowpass; ++ return 1; ++ ++err: ++ return ret; ++} ++ ++static int snd_allo_piano_dsp_program(struct snd_soc_pcm_runtime *rtd, ++ unsigned int mode, unsigned int rate, unsigned int lowpass) ++{ ++ struct snd_soc_card *card = rtd->card; ++ struct glb_pool *glb_ptr = card->drvdata; ++ int ret = 0; ++ ++ mutex_lock(&glb_ptr->lock); ++ ++ ret = __snd_allo_piano_dsp_program(rtd, mode, rate, lowpass); ++ ++ mutex_unlock(&glb_ptr->lock); ++ ++ return ret; ++} ++ ++static int snd_allo_piano_dual_mode_get(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct glb_pool *glb_ptr = card->drvdata; ++ ++ ucontrol->value.integer.value[0] = glb_ptr->dual_mode; ++ ++ return 0; ++} ++ ++static int snd_allo_piano_dual_mode_put(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct glb_pool *glb_ptr = card->drvdata; ++ struct snd_soc_pcm_runtime *rtd; ++ struct snd_card *snd_card_ptr = card->snd_card; ++ struct snd_kcontrol *kctl; ++ struct soc_mixer_control *mc; ++ unsigned int left_val = 0, right_val = 0; ++ ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ ++ if (ucontrol->value.integer.value[0] > 0) { ++ glb_ptr->dual_mode = ucontrol->value.integer.value[0]; ++ glb_ptr->set_mode = 0; ++ } else { ++ if (glb_ptr->set_mode <= 0) { ++ glb_ptr->dual_mode = 1; ++ glb_ptr->set_mode = 0; ++ } else { ++ glb_ptr->dual_mode = 0; ++ return 0; ++ } ++ } ++ ++ if (glb_ptr->dual_mode == 1) { // Dual Mono ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 0)->component, ++ PCM512x_MUTE, P_DAC_RIGHT_MUTE); ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_MUTE, P_DAC_LEFT_MUTE); ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 0)->component, ++ PCM512x_DIGITAL_VOLUME_3, 0xff); ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_DIGITAL_VOLUME_2, 0xff); ++ ++ list_for_each_entry(kctl, &snd_card_ptr->controls, list) { ++ if (!strncmp(kctl->id.name, "Digital Playback Volume", ++ sizeof(kctl->id.name))) { ++ mc = (struct soc_mixer_control *) ++ kctl->private_value; ++ mc->rreg = mc->reg; ++ break; ++ } ++ } ++ } else { ++ left_val = snd_soc_component_read(asoc_rtd_to_codec(rtd, 0)->component, ++ PCM512x_DIGITAL_VOLUME_2); ++ right_val = snd_soc_component_read(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_DIGITAL_VOLUME_3); ++ ++ list_for_each_entry(kctl, &snd_card_ptr->controls, list) { ++ if (!strncmp(kctl->id.name, "Digital Playback Volume", ++ sizeof(kctl->id.name))) { ++ mc = (struct soc_mixer_control *) ++ kctl->private_value; ++ mc->rreg = PCM512x_DIGITAL_VOLUME_3; ++ break; ++ } ++ } ++ ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 0)->component, ++ PCM512x_DIGITAL_VOLUME_3, left_val); ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_DIGITAL_VOLUME_2, right_val); ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 0)->component, ++ PCM512x_MUTE, P_DAC_UNMUTE); ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_MUTE, P_DAC_UNMUTE); ++ } ++ ++ return 0; ++} ++ ++static int snd_allo_piano_mode_get(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct glb_pool *glb_ptr = card->drvdata; ++ ++ ucontrol->value.integer.value[0] = glb_ptr->set_mode; ++ return 0; ++} ++ ++static int snd_allo_piano_mode_put(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct snd_soc_pcm_runtime *rtd; ++ struct glb_pool *glb_ptr = card->drvdata; ++ struct snd_card *snd_card_ptr = card->snd_card; ++ struct snd_kcontrol *kctl; ++ struct soc_mixer_control *mc; ++ unsigned int left_val = 0, right_val = 0; ++ ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ ++ if ((glb_ptr->dual_mode == 1) && ++ (ucontrol->value.integer.value[0] > 0)) { ++ left_val = snd_soc_component_read(asoc_rtd_to_codec(rtd, 0)->component, ++ PCM512x_DIGITAL_VOLUME_2); ++ right_val = snd_soc_component_read(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_DIGITAL_VOLUME_2); ++ ++ list_for_each_entry(kctl, &snd_card_ptr->controls, list) { ++ if (!strncmp(kctl->id.name, "Digital Playback Volume", ++ sizeof(kctl->id.name))) { ++ mc = (struct soc_mixer_control *) ++ kctl->private_value; ++ mc->rreg = PCM512x_DIGITAL_VOLUME_3; ++ break; ++ } ++ } ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 0)->component, ++ PCM512x_DIGITAL_VOLUME_3, left_val); ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_DIGITAL_VOLUME_3, right_val); ++ } ++ ++ return(snd_allo_piano_dsp_program(rtd, ++ ucontrol->value.integer.value[0], ++ glb_ptr->set_rate, glb_ptr->set_lowpass)); ++} ++ ++static int snd_allo_piano_lowpass_get(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct glb_pool *glb_ptr = card->drvdata; ++ ++ ucontrol->value.integer.value[0] = glb_ptr->set_lowpass; ++ return 0; ++} ++ ++static int snd_allo_piano_lowpass_put(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct snd_soc_pcm_runtime *rtd; ++ struct glb_pool *glb_ptr = card->drvdata; ++ ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ return(snd_allo_piano_dsp_program(rtd, ++ glb_ptr->set_mode, glb_ptr->set_rate, ++ ucontrol->value.integer.value[0])); ++} ++ ++static int pcm512x_get_reg_sub(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct soc_mixer_control *mc = ++ (struct soc_mixer_control *)kcontrol->private_value; ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct glb_pool *glb_ptr = card->drvdata; ++ struct snd_soc_pcm_runtime *rtd; ++ unsigned int left_val = 0; ++ unsigned int right_val = 0; ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ right_val = snd_soc_component_read(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_DIGITAL_VOLUME_3); ++ if (glb_ptr->dual_mode != 1) { ++ left_val = snd_soc_component_read(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_DIGITAL_VOLUME_2); ++ ++ } else { ++ left_val = right_val; ++ } ++ ++ ucontrol->value.integer.value[0] = ++ (~(left_val >> mc->shift)) & mc->max; ++ ucontrol->value.integer.value[1] = ++ (~(right_val >> mc->shift)) & mc->max; ++ ++ return 0; ++} ++ ++static int pcm512x_set_reg_sub(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct soc_mixer_control *mc = ++ (struct soc_mixer_control *)kcontrol->private_value; ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct glb_pool *glb_ptr = card->drvdata; ++ struct snd_soc_pcm_runtime *rtd; ++ unsigned int left_val = (ucontrol->value.integer.value[0] & mc->max); ++ unsigned int right_val = (ucontrol->value.integer.value[1] & mc->max); ++ int ret = 0; ++ ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ if (glb_ptr->dual_mode != 1) { ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_DIGITAL_VOLUME_2, (~left_val)); ++ if (ret < 0) ++ return ret; ++ } ++ ++ if (digital_gain_0db_limit) { ++ ret = snd_soc_limit_volume(card, "Subwoofer Playback Volume", ++ 207); ++ if (ret < 0) ++ dev_warn(card->dev, "Failed to set volume limit: %d\n", ++ ret); ++ } ++ ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_DIGITAL_VOLUME_3, (~right_val)); ++ if (ret < 0) ++ return ret; ++ ++ return 1; ++} ++ ++static int pcm512x_get_reg_sub_switch(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct snd_soc_pcm_runtime *rtd; ++ int val = 0; ++ ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ val = snd_soc_component_read(asoc_rtd_to_codec(rtd, 1)->component, PCM512x_MUTE); ++ ++ ucontrol->value.integer.value[0] = ++ (val & P_DAC_LEFT_MUTE) ? P_UNMUTE : P_MUTE; ++ ucontrol->value.integer.value[1] = ++ (val & P_DAC_RIGHT_MUTE) ? P_UNMUTE : P_MUTE; ++ ++ return val; ++} ++ ++static int pcm512x_set_reg_sub_switch(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct snd_soc_pcm_runtime *rtd; ++ struct glb_pool *glb_ptr = card->drvdata; ++ unsigned int left_val = (ucontrol->value.integer.value[0]); ++ unsigned int right_val = (ucontrol->value.integer.value[1]); ++ int ret = 0; ++ ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ if (glb_ptr->set_mode != 1) { ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, PCM512x_MUTE, ++ ~((left_val & 0x01)<<4 | (right_val & 0x01))); ++ if (ret < 0) ++ return ret; ++ } ++ return 1; ++ ++} ++ ++static int pcm512x_get_reg_master(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct soc_mixer_control *mc = ++ (struct soc_mixer_control *)kcontrol->private_value; ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct glb_pool *glb_ptr = card->drvdata; ++ struct snd_soc_pcm_runtime *rtd; ++ unsigned int left_val = 0, right_val = 0; ++ ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ ++ left_val = snd_soc_component_read(asoc_rtd_to_codec(rtd, 0)->component, ++ PCM512x_DIGITAL_VOLUME_2); ++ ++ if (glb_ptr->dual_mode == 1) { ++ right_val = snd_soc_component_read(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_DIGITAL_VOLUME_3); ++ } else { ++ right_val = snd_soc_component_read(asoc_rtd_to_codec(rtd, 0)->component, ++ PCM512x_DIGITAL_VOLUME_3); ++ } ++ ++ ucontrol->value.integer.value[0] = ++ (~(left_val >> mc->shift)) & mc->max; ++ ucontrol->value.integer.value[1] = ++ (~(right_val >> mc->shift)) & mc->max; ++ ++ return 0; ++} ++ ++static int pcm512x_set_reg_master(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct soc_mixer_control *mc = ++ (struct soc_mixer_control *)kcontrol->private_value; ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct glb_pool *glb_ptr = card->drvdata; ++ struct snd_soc_pcm_runtime *rtd; ++ unsigned int left_val = (ucontrol->value.integer.value[0] & mc->max); ++ unsigned int right_val = (ucontrol->value.integer.value[1] & mc->max); ++ int ret = 0; ++ ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ ++ if (digital_gain_0db_limit) { ++ ret = snd_soc_limit_volume(card, "Master Playback Volume", ++ 207); ++ if (ret < 0) ++ dev_warn(card->dev, "Failed to set volume limit: %d\n", ++ ret); ++ } ++ ++ if (glb_ptr->dual_mode != 1) { ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_DIGITAL_VOLUME_2, (~left_val)); ++ if (ret < 0) ++ return ret; ++ ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, 0)->component, ++ PCM512x_DIGITAL_VOLUME_3, (~right_val)); ++ if (ret < 0) ++ return ret; ++ ++ } ++ ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, ++ PCM512x_DIGITAL_VOLUME_3, (~right_val)); ++ if (ret < 0) ++ return ret; ++ ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, 0)->component, ++ PCM512x_DIGITAL_VOLUME_2, (~left_val)); ++ if (ret < 0) ++ return ret; ++ return 1; ++} ++ ++static int pcm512x_get_reg_master_switch(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct glb_pool *glb_ptr = card->drvdata; ++ struct snd_soc_pcm_runtime *rtd; ++ int val = 0; ++ ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ ++ val = snd_soc_component_read(asoc_rtd_to_codec(rtd, 0)->component, PCM512x_MUTE); ++ ++ ucontrol->value.integer.value[0] = ++ (val & P_DAC_LEFT_MUTE) ? P_UNMUTE : P_MUTE; ++ ++ if (glb_ptr->dual_mode == 1) { ++ val = snd_soc_component_read(asoc_rtd_to_codec(rtd, 1)->component, PCM512x_MUTE); ++ } ++ ucontrol->value.integer.value[1] = ++ (val & P_DAC_RIGHT_MUTE) ? P_UNMUTE : P_MUTE; ++ ++ return val; ++} ++ ++static int pcm512x_set_reg_master_switch(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct snd_soc_pcm_runtime *rtd; ++ struct glb_pool *glb_ptr = card->drvdata; ++ unsigned int left_val = (ucontrol->value.integer.value[0]); ++ unsigned int right_val = (ucontrol->value.integer.value[1]); ++ int ret = 0; ++ ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ if (glb_ptr->dual_mode == 1) { ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, 0)->component, PCM512x_MUTE, ++ ~((left_val & 0x01)<<4)); ++ if (ret < 0) ++ return ret; ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, PCM512x_MUTE, ++ ~((right_val & 0x01))); ++ if (ret < 0) ++ return ret; ++ ++ } else if (glb_ptr->set_mode == 1) { ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, 0)->component, PCM512x_MUTE, ++ ~((left_val & 0x01)<<4 | (right_val & 0x01))); ++ if (ret < 0) ++ return ret; ++ ++ } else { ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, 0)->component, PCM512x_MUTE, ++ ~((left_val & 0x01)<<4 | (right_val & 0x01))); ++ if (ret < 0) ++ return ret; ++ ++ ret = snd_soc_component_write(asoc_rtd_to_codec(rtd, 1)->component, PCM512x_MUTE, ++ ~((left_val & 0x01)<<4 | (right_val & 0x01))); ++ if (ret < 0) ++ return ret; ++ } ++ return 1; ++} ++ ++static const DECLARE_TLV_DB_SCALE(digital_tlv_sub, -10350, 50, 1); ++static const DECLARE_TLV_DB_SCALE(digital_tlv_master, -10350, 50, 1); ++ ++static const struct snd_kcontrol_new allo_piano_controls[] = { ++ SOC_ENUM_EXT("Subwoofer mode Route", ++ allo_piano_mode_enum, ++ snd_allo_piano_mode_get, ++ snd_allo_piano_mode_put), ++ ++ SOC_ENUM_EXT("Dual Mode Route", ++ allo_piano_dual_mode_enum, ++ snd_allo_piano_dual_mode_get, ++ snd_allo_piano_dual_mode_put), ++ ++ SOC_ENUM_EXT("Lowpass Route", allo_piano_enum, ++ snd_allo_piano_lowpass_get, ++ snd_allo_piano_lowpass_put), ++ ++ SOC_DOUBLE_R_EXT_TLV("Subwoofer Playback Volume", ++ PCM512x_DIGITAL_VOLUME_2, ++ PCM512x_DIGITAL_VOLUME_3, 0, 255, 1, ++ pcm512x_get_reg_sub, ++ pcm512x_set_reg_sub, ++ digital_tlv_sub), ++ ++ SOC_DOUBLE_EXT("Subwoofer Playback Switch", ++ PCM512x_MUTE, ++ PCM512x_RQML_SHIFT, ++ PCM512x_RQMR_SHIFT, 1, 1, ++ pcm512x_get_reg_sub_switch, ++ pcm512x_set_reg_sub_switch), ++ ++ SOC_DOUBLE_R_EXT_TLV("Master Playback Volume", ++ PCM512x_DIGITAL_VOLUME_2, ++ PCM512x_DIGITAL_VOLUME_3, 0, 255, 1, ++ pcm512x_get_reg_master, ++ pcm512x_set_reg_master, ++ digital_tlv_master), ++ ++ SOC_DOUBLE_EXT("Master Playback Switch", ++ PCM512x_MUTE, ++ PCM512x_RQML_SHIFT, ++ PCM512x_RQMR_SHIFT, 1, 1, ++ pcm512x_get_reg_master_switch, ++ pcm512x_set_reg_master_switch), ++}; ++ ++static int snd_allo_piano_dac_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_card *card = rtd->card; ++ struct glb_pool *glb_ptr; ++ ++ glb_ptr = kzalloc(sizeof(struct glb_pool), GFP_KERNEL); ++ if (!glb_ptr) ++ return -ENOMEM; ++ ++ card->drvdata = glb_ptr; ++ glb_ptr->dual_mode = 2; ++ glb_ptr->set_mode = 0; ++ ++ mutex_init(&glb_ptr->lock); ++ ++ if (digital_gain_0db_limit) { ++ int ret; ++ ++ ret = snd_soc_limit_volume(card, "Digital Playback Volume", ++ 207); ++ if (ret < 0) ++ dev_warn(card->dev, "Failed to set volume limit: %d\n", ++ ret); ++ } ++ return 0; ++} ++ ++static void snd_allo_piano_gpio_mute(struct snd_soc_card *card) ++{ ++ if (mute_gpio[0]) ++ gpiod_set_value_cansleep(mute_gpio[0], P_MUTE); ++ ++ if (mute_gpio[1]) ++ gpiod_set_value_cansleep(mute_gpio[1], P_MUTE); ++} ++ ++static void snd_allo_piano_gpio_unmute(struct snd_soc_card *card) ++{ ++ if (mute_gpio[0]) ++ gpiod_set_value_cansleep(mute_gpio[0], P_UNMUTE); ++ ++ if (mute_gpio[1]) ++ gpiod_set_value_cansleep(mute_gpio[1], P_UNMUTE); ++} ++ ++static int snd_allo_piano_set_bias_level(struct snd_soc_card *card, ++ struct snd_soc_dapm_context *dapm, enum snd_soc_bias_level level) ++{ ++ struct snd_soc_pcm_runtime *rtd; ++ struct snd_soc_dai *codec_dai; ++ ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ codec_dai = asoc_rtd_to_codec(rtd, 0); ++ ++ if (dapm->dev != codec_dai->dev) ++ return 0; ++ ++ switch (level) { ++ case SND_SOC_BIAS_PREPARE: ++ if (dapm->bias_level != SND_SOC_BIAS_STANDBY) ++ break; ++ /* UNMUTE DAC */ ++ snd_allo_piano_gpio_unmute(card); ++ break; ++ ++ case SND_SOC_BIAS_STANDBY: ++ if (dapm->bias_level != SND_SOC_BIAS_PREPARE) ++ break; ++ /* MUTE DAC */ ++ snd_allo_piano_gpio_mute(card); ++ break; ++ ++ default: ++ break; ++ } ++ ++ return 0; ++} ++ ++static int snd_allo_piano_dac_startup( ++ struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_card *card = rtd->card; ++ ++ snd_allo_piano_gpio_mute(card); ++ ++ return 0; ++} ++ ++static int snd_allo_piano_dac_hw_params( ++ struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ unsigned int rate = params_rate(params); ++ struct snd_soc_card *card = rtd->card; ++ struct glb_pool *glb_ptr = card->drvdata; ++ int ret = 0, val = 0, dac; ++ ++ for (dac = 0; (glb_mclk && dac < 2); dac++) { ++ /* Configure the PLL clock reference for both the Codecs */ ++ val = snd_soc_component_read(asoc_rtd_to_codec(rtd, dac)->component, ++ PCM512x_RATE_DET_4); ++ ++ if (val & 0x40) { ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, dac)->component, ++ PCM512x_PLL_REF, ++ PCM512x_SREF_BCK); ++ ++ dev_info(asoc_rtd_to_codec(rtd, dac)->component->dev, ++ "Setting BCLK as input clock & Enable PLL\n"); ++ } else { ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, dac)->component, ++ PCM512x_PLL_EN, ++ 0x00); ++ ++ snd_soc_component_write(asoc_rtd_to_codec(rtd, dac)->component, ++ PCM512x_PLL_REF, ++ PCM512x_SREF_SCK); ++ ++ dev_info(asoc_rtd_to_codec(rtd, dac)->component->dev, ++ "Setting SCLK as input clock & disabled PLL\n"); ++ } ++ } ++ ++ ret = snd_allo_piano_dsp_program(rtd, glb_ptr->set_mode, rate, ++ glb_ptr->set_lowpass); ++ if (ret < 0) ++ return ret; ++ ++ return ret; ++} ++ ++static int snd_allo_piano_dac_prepare( ++ struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_card *card = rtd->card; ++ ++ snd_allo_piano_gpio_unmute(card); ++ ++ return 0; ++} ++ ++/* machine stream operations */ ++static struct snd_soc_ops snd_allo_piano_dac_ops = { ++ .startup = snd_allo_piano_dac_startup, ++ .hw_params = snd_allo_piano_dac_hw_params, ++ .prepare = snd_allo_piano_dac_prepare, ++}; ++ ++static struct snd_soc_dai_link_component allo_piano_2_1_codecs[] = { ++ { ++ .dai_name = "pcm512x-hifi", ++ }, ++ { ++ .dai_name = "pcm512x-hifi", ++ }, ++}; ++ ++SND_SOC_DAILINK_DEFS(allo_piano_dai_plus, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC(NULL, "pcm512x-hifi"), ++ COMP_CODEC(NULL, "pcm512x-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_allo_piano_dac_dai[] = { ++ { ++ .name = "PianoDACPlus", ++ .stream_name = "PianoDACPlus", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | ++ SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ .ops = &snd_allo_piano_dac_ops, ++ .init = snd_allo_piano_dac_init, ++ SND_SOC_DAILINK_REG(allo_piano_dai_plus), ++ }, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_allo_piano_dac = { ++ .name = "PianoDACPlus", ++ .owner = THIS_MODULE, ++ .dai_link = snd_allo_piano_dac_dai, ++ .num_links = ARRAY_SIZE(snd_allo_piano_dac_dai), ++ .controls = allo_piano_controls, ++ .num_controls = ARRAY_SIZE(allo_piano_controls), ++}; ++ ++static int snd_allo_piano_dac_probe(struct platform_device *pdev) ++{ ++ struct snd_soc_card *card = &snd_allo_piano_dac; ++ int ret = 0, i = 0; ++ ++ card->dev = &pdev->dev; ++ platform_set_drvdata(pdev, &snd_allo_piano_dac); ++ ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai; ++ ++ dai = &snd_allo_piano_dac_dai[0]; ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ if (i2s_node) { ++ for (i = 0; i < card->num_links; i++) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } ++ } ++ digital_gain_0db_limit = ++ !of_property_read_bool(pdev->dev.of_node, ++ "allo,24db_digital_gain"); ++ ++ glb_mclk = of_property_read_bool(pdev->dev.of_node, ++ "allo,glb_mclk"); ++ ++ allo_piano_2_1_codecs[0].of_node = ++ of_parse_phandle(pdev->dev.of_node, "audio-codec", 0); ++ if (!allo_piano_2_1_codecs[0].of_node) { ++ dev_err(&pdev->dev, ++ "Property 'audio-codec' missing or invalid\n"); ++ return -EINVAL; ++ } ++ ++ allo_piano_2_1_codecs[1].of_node = ++ of_parse_phandle(pdev->dev.of_node, "audio-codec", 1); ++ if (!allo_piano_2_1_codecs[1].of_node) { ++ dev_err(&pdev->dev, ++ "Property 'audio-codec' missing or invalid\n"); ++ return -EINVAL; ++ } ++ ++ mute_gpio[0] = devm_gpiod_get_optional(&pdev->dev, "mute1", ++ GPIOD_OUT_LOW); ++ if (IS_ERR(mute_gpio[0])) { ++ ret = PTR_ERR(mute_gpio[0]); ++ dev_err(&pdev->dev, ++ "failed to get mute1 gpio6: %d\n", ret); ++ return ret; ++ } ++ ++ mute_gpio[1] = devm_gpiod_get_optional(&pdev->dev, "mute2", ++ GPIOD_OUT_LOW); ++ if (IS_ERR(mute_gpio[1])) { ++ ret = PTR_ERR(mute_gpio[1]); ++ dev_err(&pdev->dev, ++ "failed to get mute2 gpio25: %d\n", ret); ++ return ret; ++ } ++ ++ if (mute_gpio[0] && mute_gpio[1]) ++ snd_allo_piano_dac.set_bias_level = ++ snd_allo_piano_set_bias_level; ++ ++ ret = snd_soc_register_card(&snd_allo_piano_dac); ++ if (ret < 0) { ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ return ret; ++ } ++ ++ if ((mute_gpio[0]) && (mute_gpio[1])) ++ snd_allo_piano_gpio_mute(&snd_allo_piano_dac); ++ ++ return 0; ++ } ++ ++ return -EINVAL; ++} ++ ++static int snd_allo_piano_dac_remove(struct platform_device *pdev) ++{ ++ struct snd_soc_card *card = platform_get_drvdata(pdev); ++ ++ kfree(&card->drvdata); ++ snd_allo_piano_gpio_mute(&snd_allo_piano_dac); ++ return snd_soc_unregister_card(&snd_allo_piano_dac); ++} ++ ++static const struct of_device_id snd_allo_piano_dac_of_match[] = { ++ { .compatible = "allo,piano-dac-plus", }, ++ { /* sentinel */ }, ++}; ++ ++MODULE_DEVICE_TABLE(of, snd_allo_piano_dac_of_match); ++ ++static struct platform_driver snd_allo_piano_dac_driver = { ++ .driver = { ++ .name = "snd-allo-piano-dac-plus", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_allo_piano_dac_of_match, ++ }, ++ .probe = snd_allo_piano_dac_probe, ++ .remove = snd_allo_piano_dac_remove, ++}; ++ ++module_platform_driver(snd_allo_piano_dac_driver); ++ ++MODULE_AUTHOR("Baswaraj K "); ++MODULE_DESCRIPTION("ALSA ASoC Machine Driver for Allo Piano DAC Plus"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/allo-piano-dac.c +@@ -0,0 +1,122 @@ ++/* ++ * ALSA ASoC Machine Driver for Allo Piano DAC ++ * ++ * Author: Baswaraj K ++ * Copyright 2016 ++ * based on code by Daniel Matuschek ++ * based on code by Florian Meier ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++static bool digital_gain_0db_limit = true; ++ ++static int snd_allo_piano_dac_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ if (digital_gain_0db_limit) { ++ int ret; ++ struct snd_soc_card *card = rtd->card; ++ ++ ret = snd_soc_limit_volume(card, "Digital Playback Volume", ++ 207); ++ if (ret < 0) ++ dev_warn(card->dev, "Failed to set volume limit: %d\n", ++ ret); ++ } ++ ++ return 0; ++} ++ ++SND_SOC_DAILINK_DEFS(allo_piano_dai, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("pcm512x.1-004c", "pcm512x-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_allo_piano_dac_dai[] = { ++{ ++ .name = "Piano DAC", ++ .stream_name = "Piano DAC HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | ++ SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ .init = snd_allo_piano_dac_init, ++ SND_SOC_DAILINK_REG(allo_piano_dai), ++}, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_allo_piano_dac = { ++ .name = "PianoDAC", ++ .owner = THIS_MODULE, ++ .dai_link = snd_allo_piano_dac_dai, ++ .num_links = ARRAY_SIZE(snd_allo_piano_dac_dai), ++}; ++ ++static int snd_allo_piano_dac_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ ++ snd_allo_piano_dac.dev = &pdev->dev; ++ ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai; ++ ++ dai = &snd_allo_piano_dac_dai[0]; ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ ++ if (i2s_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } ++ ++ digital_gain_0db_limit = !of_property_read_bool( ++ pdev->dev.of_node, "allo,24db_digital_gain"); ++ } ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, &snd_allo_piano_dac); ++ if (ret && ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ ++ return ret; ++} ++ ++static const struct of_device_id snd_allo_piano_dac_of_match[] = { ++ { .compatible = "allo,piano-dac", }, ++ { /* sentinel */ }, ++}; ++MODULE_DEVICE_TABLE(of, snd_allo_piano_dac_of_match); ++ ++static struct platform_driver snd_allo_piano_dac_driver = { ++ .driver = { ++ .name = "snd-allo-piano-dac", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_allo_piano_dac_of_match, ++ }, ++ .probe = snd_allo_piano_dac_probe, ++}; ++ ++module_platform_driver(snd_allo_piano_dac_driver); ++ ++MODULE_AUTHOR("Baswaraj K "); ++MODULE_DESCRIPTION("ALSA ASoC Machine Driver for Allo Piano DAC"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/audioinjector-isolated-soundcard.c +@@ -0,0 +1,183 @@ ++/* ++ * ASoC Driver for AudioInjector.net isolated soundcard ++ * ++ * Created on: 20-February-2020 ++ * Author: flatmax@flatmax.org ++ * based on audioinjector-octo-soundcard.c ++ * ++ * Copyright (C) 2020 Flatmax Pty. Ltd. ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++static struct gpio_desc *mute_gpio; ++ ++static const unsigned int audioinjector_isolated_rates[] = { ++ 192000, 96000, 48000, 32000, 24000, 16000, 8000 ++}; ++ ++static struct snd_pcm_hw_constraint_list audioinjector_isolated_constraints = { ++ .list = audioinjector_isolated_rates, ++ .count = ARRAY_SIZE(audioinjector_isolated_rates), ++}; ++ ++static int audioinjector_isolated_dai_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ int ret=snd_soc_dai_set_sysclk(asoc_rtd_to_codec(rtd, 0), 0, 24576000, 0); ++ if (ret) ++ return ret; ++ ++ return snd_soc_dai_set_bclk_ratio(asoc_rtd_to_cpu(rtd, 0), 64); ++} ++ ++static int audioinjector_isolated_startup(struct snd_pcm_substream *substream) ++{ ++ snd_pcm_hw_constraint_list(substream->runtime, 0, ++ SNDRV_PCM_HW_PARAM_RATE, &audioinjector_isolated_constraints); ++ ++ return 0; ++} ++ ++static int audioinjector_isolated_trigger(struct snd_pcm_substream *substream, ++ int cmd){ ++ ++ switch (cmd) { ++ case SNDRV_PCM_TRIGGER_STOP: ++ case SNDRV_PCM_TRIGGER_SUSPEND: ++ case SNDRV_PCM_TRIGGER_PAUSE_PUSH: ++ gpiod_set_value(mute_gpio, 0); ++ break; ++ case SNDRV_PCM_TRIGGER_START: ++ case SNDRV_PCM_TRIGGER_RESUME: ++ case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: ++ gpiod_set_value(mute_gpio, 1); ++ break; ++ default: ++ return -EINVAL; ++ } ++ return 0; ++} ++ ++static struct snd_soc_ops audioinjector_isolated_ops = { ++ .startup = audioinjector_isolated_startup, ++ .trigger = audioinjector_isolated_trigger, ++}; ++ ++SND_SOC_DAILINK_DEFS(audioinjector_isolated, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("cs4271.1-0010", "cs4271-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link audioinjector_isolated_dai[] = { ++ { ++ .name = "AudioInjector ISO", ++ .stream_name = "AI-HIFI", ++ .ops = &audioinjector_isolated_ops, ++ .init = audioinjector_isolated_dai_init, ++ .symmetric_rates = 1, ++ .symmetric_channels = 1, ++ .dai_fmt = SND_SOC_DAIFMT_CBM_CFM|SND_SOC_DAIFMT_I2S|SND_SOC_DAIFMT_NB_NF, ++ SND_SOC_DAILINK_REG(audioinjector_isolated), ++ } ++}; ++ ++static const struct snd_soc_dapm_widget audioinjector_isolated_widgets[] = { ++ SND_SOC_DAPM_OUTPUT("OUTPUTS"), ++ SND_SOC_DAPM_INPUT("INPUTS"), ++}; ++ ++static const struct snd_soc_dapm_route audioinjector_isolated_route[] = { ++ /* Balanced outputs */ ++ {"OUTPUTS", NULL, "AOUTA+"}, ++ {"OUTPUTS", NULL, "AOUTA-"}, ++ {"OUTPUTS", NULL, "AOUTB+"}, ++ {"OUTPUTS", NULL, "AOUTB-"}, ++ ++ /* Balanced inputs */ ++ {"AINA", NULL, "INPUTS"}, ++ {"AINB", NULL, "INPUTS"}, ++}; ++ ++static struct snd_soc_card snd_soc_audioinjector_isolated = { ++ .name = "audioinjector-isolated-soundcard", ++ .dai_link = audioinjector_isolated_dai, ++ .num_links = ARRAY_SIZE(audioinjector_isolated_dai), ++ ++ .dapm_widgets = audioinjector_isolated_widgets, ++ .num_dapm_widgets = ARRAY_SIZE(audioinjector_isolated_widgets), ++ .dapm_routes = audioinjector_isolated_route, ++ .num_dapm_routes = ARRAY_SIZE(audioinjector_isolated_route), ++}; ++ ++static int audioinjector_isolated_probe(struct platform_device *pdev) ++{ ++ struct snd_soc_card *card = &snd_soc_audioinjector_isolated; ++ int ret; ++ ++ card->dev = &pdev->dev; ++ ++ if (pdev->dev.of_node) { ++ struct snd_soc_dai_link *dai = &audioinjector_isolated_dai[0]; ++ struct device_node *i2s_node = ++ of_parse_phandle(pdev->dev.of_node, "i2s-controller", 0); ++ ++ if (i2s_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } else { ++ dev_err(&pdev->dev, ++ "i2s-controller missing or invalid in DT\n"); ++ return -EINVAL; ++ } ++ ++ mute_gpio = devm_gpiod_get_optional(&pdev->dev, "mute", GPIOD_OUT_LOW); ++ if (IS_ERR(mute_gpio)){ ++ dev_err(&pdev->dev, "mute gpio not found in dt overlay\n"); ++ return PTR_ERR(mute_gpio); ++ } ++ } ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, card); ++ if (ret && ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", ret); ++ return ret; ++} ++ ++static const struct of_device_id audioinjector_isolated_of_match[] = { ++ { .compatible = "ai,audioinjector-isolated-soundcard", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, audioinjector_isolated_of_match); ++ ++static struct platform_driver audioinjector_isolated_driver = { ++ .driver = { ++ .name = "audioinjector-isolated", ++ .owner = THIS_MODULE, ++ .of_match_table = audioinjector_isolated_of_match, ++ }, ++ .probe = audioinjector_isolated_probe, ++}; ++ ++module_platform_driver(audioinjector_isolated_driver); ++MODULE_AUTHOR("Matt Flax "); ++MODULE_DESCRIPTION("AudioInjector.net isolated Soundcard"); ++MODULE_LICENSE("GPL v2"); ++MODULE_ALIAS("platform:audioinjector-isolated-soundcard"); +--- /dev/null ++++ b/sound/soc/bcm/audioinjector-octo-soundcard.c +@@ -0,0 +1,346 @@ ++/* ++ * ASoC Driver for AudioInjector Pi octo channel soundcard (hat) ++ * ++ * Created on: 27-October-2016 ++ * Author: flatmax@flatmax.org ++ * based on audioinjector-pi-soundcard.c ++ * ++ * Copyright (C) 2016 Flatmax Pty. Ltd. ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++static struct gpio_descs *mult_gpios; ++static struct gpio_desc *codec_rst_gpio; ++static unsigned int audioinjector_octo_rate; ++static bool non_stop_clocks; ++ ++static const unsigned int audioinjector_octo_rates[] = { ++ 96000, 48000, 32000, 24000, 16000, 8000, 88200, 44100, 29400, 22050, 14700, ++}; ++ ++static struct snd_pcm_hw_constraint_list audioinjector_octo_constraints = { ++ .list = audioinjector_octo_rates, ++ .count = ARRAY_SIZE(audioinjector_octo_rates), ++}; ++ ++static int audioinjector_octo_dai_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ return snd_soc_dai_set_bclk_ratio(asoc_rtd_to_cpu(rtd, 0), 64); ++} ++ ++static int audioinjector_octo_startup(struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ asoc_rtd_to_cpu(rtd, 0)->driver->playback.channels_min = 8; ++ asoc_rtd_to_cpu(rtd, 0)->driver->playback.channels_max = 8; ++ asoc_rtd_to_cpu(rtd, 0)->driver->capture.channels_min = 8; ++ asoc_rtd_to_cpu(rtd, 0)->driver->capture.channels_max = 8; ++ asoc_rtd_to_codec(rtd, 0)->driver->capture.channels_max = 8; ++ ++ snd_pcm_hw_constraint_list(substream->runtime, 0, ++ SNDRV_PCM_HW_PARAM_RATE, ++ &audioinjector_octo_constraints); ++ ++ return 0; ++} ++ ++static void audioinjector_octo_shutdown(struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ asoc_rtd_to_cpu(rtd, 0)->driver->playback.channels_min = 2; ++ asoc_rtd_to_cpu(rtd, 0)->driver->playback.channels_max = 2; ++ asoc_rtd_to_cpu(rtd, 0)->driver->capture.channels_min = 2; ++ asoc_rtd_to_cpu(rtd, 0)->driver->capture.channels_max = 2; ++ asoc_rtd_to_codec(rtd, 0)->driver->capture.channels_max = 6; ++} ++ ++static int audioinjector_octo_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ ++ // set codec DAI configuration ++ int ret = snd_soc_dai_set_fmt(asoc_rtd_to_codec(rtd, 0), ++ SND_SOC_DAIFMT_CBS_CFS|SND_SOC_DAIFMT_DSP_A| ++ SND_SOC_DAIFMT_NB_NF); ++ if (ret < 0) ++ return ret; ++ ++ // set cpu DAI configuration ++ ret = snd_soc_dai_set_fmt(asoc_rtd_to_cpu(rtd, 0), ++ SND_SOC_DAIFMT_CBM_CFM|SND_SOC_DAIFMT_I2S| ++ SND_SOC_DAIFMT_NB_NF); ++ if (ret < 0) ++ return ret; ++ ++ audioinjector_octo_rate = params_rate(params); ++ ++ // Set the correct sysclock for the codec ++ switch (audioinjector_octo_rate) { ++ case 96000: ++ case 48000: ++ return snd_soc_dai_set_sysclk(asoc_rtd_to_codec(rtd, 0), 0, 49152000, ++ 0); ++ break; ++ case 24000: ++ return snd_soc_dai_set_sysclk(asoc_rtd_to_codec(rtd, 0), 0, 49152000/2, ++ 0); ++ break; ++ case 32000: ++ case 16000: ++ return snd_soc_dai_set_sysclk(asoc_rtd_to_codec(rtd, 0), 0, 49152000/3, ++ 0); ++ break; ++ case 8000: ++ return snd_soc_dai_set_sysclk(asoc_rtd_to_codec(rtd, 0), 0, 49152000/6, ++ 0); ++ break; ++ case 88200: ++ case 44100: ++ return snd_soc_dai_set_sysclk(asoc_rtd_to_codec(rtd, 0), 0, 45185400, ++ 0); ++ break; ++ case 22050: ++ return snd_soc_dai_set_sysclk(asoc_rtd_to_codec(rtd, 0), 0, 45185400/2, ++ 0); ++ break; ++ case 29400: ++ case 14700: ++ return snd_soc_dai_set_sysclk(asoc_rtd_to_codec(rtd, 0), 0, 45185400/3, ++ 0); ++ break; ++ default: ++ return -EINVAL; ++ } ++} ++ ++static int audioinjector_octo_trigger(struct snd_pcm_substream *substream, ++ int cmd){ ++ DECLARE_BITMAP(mult, 4); ++ ++ memset(mult, 0, sizeof(mult)); ++ ++ switch (cmd) { ++ case SNDRV_PCM_TRIGGER_STOP: ++ case SNDRV_PCM_TRIGGER_SUSPEND: ++ case SNDRV_PCM_TRIGGER_PAUSE_PUSH: ++ if (!non_stop_clocks) ++ break; ++ /* fall through */ ++ case SNDRV_PCM_TRIGGER_START: ++ case SNDRV_PCM_TRIGGER_RESUME: ++ case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: ++ switch (audioinjector_octo_rate) { ++ case 96000: ++ __assign_bit(3, mult, 1); ++ /* fall through */ ++ case 88200: ++ __assign_bit(1, mult, 1); ++ __assign_bit(2, mult, 1); ++ break; ++ case 48000: ++ __assign_bit(3, mult, 1); ++ /* fall through */ ++ case 44100: ++ __assign_bit(2, mult, 1); ++ break; ++ case 32000: ++ __assign_bit(3, mult, 1); ++ /* fall through */ ++ case 29400: ++ __assign_bit(0, mult, 1); ++ __assign_bit(1, mult, 1); ++ break; ++ case 24000: ++ __assign_bit(3, mult, 1); ++ /* fall through */ ++ case 22050: ++ __assign_bit(1, mult, 1); ++ break; ++ case 16000: ++ __assign_bit(3, mult, 1); ++ /* fall through */ ++ case 14700: ++ __assign_bit(0, mult, 1); ++ break; ++ case 8000: ++ __assign_bit(3, mult, 1); ++ break; ++ default: ++ return -EINVAL; ++ } ++ break; ++ default: ++ return -EINVAL; ++ } ++ gpiod_set_array_value_cansleep(mult_gpios->ndescs, mult_gpios->desc, ++ NULL, mult); ++ ++ return 0; ++} ++ ++static struct snd_soc_ops audioinjector_octo_ops = { ++ .startup = audioinjector_octo_startup, ++ .shutdown = audioinjector_octo_shutdown, ++ .hw_params = audioinjector_octo_hw_params, ++ .trigger = audioinjector_octo_trigger, ++}; ++ ++SND_SOC_DAILINK_DEFS(audioinjector_octo, ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_CODEC(NULL, "cs42448")), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++static struct snd_soc_dai_link audioinjector_octo_dai[] = { ++ { ++ .name = "AudioInjector Octo", ++ .stream_name = "AudioInject-HIFI", ++ .ops = &audioinjector_octo_ops, ++ .init = audioinjector_octo_dai_init, ++ .symmetric_rates = 1, ++ .symmetric_channels = 1, ++ SND_SOC_DAILINK_REG(audioinjector_octo), ++ }, ++}; ++ ++static const struct snd_soc_dapm_widget audioinjector_octo_widgets[] = { ++ SND_SOC_DAPM_OUTPUT("OUTPUTS0"), ++ SND_SOC_DAPM_OUTPUT("OUTPUTS1"), ++ SND_SOC_DAPM_OUTPUT("OUTPUTS2"), ++ SND_SOC_DAPM_OUTPUT("OUTPUTS3"), ++ SND_SOC_DAPM_INPUT("INPUTS0"), ++ SND_SOC_DAPM_INPUT("INPUTS1"), ++ SND_SOC_DAPM_INPUT("INPUTS2"), ++}; ++ ++static const struct snd_soc_dapm_route audioinjector_octo_route[] = { ++ /* Balanced outputs */ ++ {"OUTPUTS0", NULL, "AOUT1L"}, ++ {"OUTPUTS0", NULL, "AOUT1R"}, ++ {"OUTPUTS1", NULL, "AOUT2L"}, ++ {"OUTPUTS1", NULL, "AOUT2R"}, ++ {"OUTPUTS2", NULL, "AOUT3L"}, ++ {"OUTPUTS2", NULL, "AOUT3R"}, ++ {"OUTPUTS3", NULL, "AOUT4L"}, ++ {"OUTPUTS3", NULL, "AOUT4R"}, ++ ++ /* Balanced inputs */ ++ {"AIN1L", NULL, "INPUTS0"}, ++ {"AIN1R", NULL, "INPUTS0"}, ++ {"AIN2L", NULL, "INPUTS1"}, ++ {"AIN2R", NULL, "INPUTS1"}, ++ {"AIN3L", NULL, "INPUTS2"}, ++ {"AIN3R", NULL, "INPUTS2"}, ++}; ++ ++static struct snd_soc_card snd_soc_audioinjector_octo = { ++ .name = "audioinjector-octo-soundcard", ++ .dai_link = audioinjector_octo_dai, ++ .num_links = ARRAY_SIZE(audioinjector_octo_dai), ++ ++ .dapm_widgets = audioinjector_octo_widgets, ++ .num_dapm_widgets = ARRAY_SIZE(audioinjector_octo_widgets), ++ .dapm_routes = audioinjector_octo_route, ++ .num_dapm_routes = ARRAY_SIZE(audioinjector_octo_route), ++}; ++ ++static int audioinjector_octo_probe(struct platform_device *pdev) ++{ ++ struct snd_soc_card *card = &snd_soc_audioinjector_octo; ++ int ret; ++ ++ card->dev = &pdev->dev; ++ ++ if (pdev->dev.of_node) { ++ struct snd_soc_dai_link *dai = &audioinjector_octo_dai[0]; ++ struct device_node *i2s_node = ++ of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ struct device_node *codec_node = ++ of_parse_phandle(pdev->dev.of_node, ++ "codec", 0); ++ ++ mult_gpios = devm_gpiod_get_array_optional(&pdev->dev, "mult", ++ GPIOD_OUT_LOW); ++ if (IS_ERR(mult_gpios)) ++ return PTR_ERR(mult_gpios); ++ ++ codec_rst_gpio = devm_gpiod_get_optional(&pdev->dev, "reset", ++ GPIOD_OUT_LOW); ++ if (IS_ERR(codec_rst_gpio)) ++ return PTR_ERR(codec_rst_gpio); ++ ++ non_stop_clocks = of_property_read_bool(pdev->dev.of_node, "non-stop-clocks"); ++ ++ if (codec_rst_gpio) ++ gpiod_set_value(codec_rst_gpio, 1); ++ msleep(500); ++ if (codec_rst_gpio) ++ gpiod_set_value(codec_rst_gpio, 0); ++ msleep(500); ++ if (codec_rst_gpio) ++ gpiod_set_value(codec_rst_gpio, 1); ++ msleep(500); ++ ++ if (i2s_node && codec_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ dai->codecs->name = NULL; ++ dai->codecs->of_node = codec_node; ++ } else ++ if (!i2s_node) { ++ dev_err(&pdev->dev, ++ "i2s-controller missing or invalid in DT\n"); ++ return -EINVAL; ++ } else { ++ dev_err(&pdev->dev, ++ "Property 'codec' missing or invalid\n"); ++ return -EINVAL; ++ } ++ } ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, card); ++ if (ret != 0) ++ dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", ret); ++ return ret; ++} ++ ++static const struct of_device_id audioinjector_octo_of_match[] = { ++ { .compatible = "ai,audioinjector-octo-soundcard", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, audioinjector_octo_of_match); ++ ++static struct platform_driver audioinjector_octo_driver = { ++ .driver = { ++ .name = "audioinjector-octo", ++ .owner = THIS_MODULE, ++ .of_match_table = audioinjector_octo_of_match, ++ }, ++ .probe = audioinjector_octo_probe, ++}; ++ ++module_platform_driver(audioinjector_octo_driver); ++MODULE_AUTHOR("Matt Flax "); ++MODULE_DESCRIPTION("AudioInjector.net octo Soundcard"); ++MODULE_LICENSE("GPL v2"); ++MODULE_ALIAS("platform:audioinjector-octo-soundcard"); +--- /dev/null ++++ b/sound/soc/bcm/audioinjector-pi-soundcard.c +@@ -0,0 +1,187 @@ ++/* ++ * ASoC Driver for AudioInjector Pi add on soundcard ++ * ++ * Created on: 13-May-2016 ++ * Author: flatmax@flatmax.org ++ * based on code by Cliff Cai for the ssm2602 machine blackfin. ++ * with help from Lars-Peter Clausen for simplifying the original code to use the dai_fmt field. ++ * i2s_node code taken from the other sound/soc/bcm machine drivers. ++ * ++ * Copyright (C) 2016 Flatmax Pty. Ltd. ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++#include "../codecs/wm8731.h" ++ ++static const unsigned int bcm2835_rates_12000000[] = { ++ 8000, 16000, 32000, 44100, 48000, 96000, 88200, ++}; ++ ++static struct snd_pcm_hw_constraint_list bcm2835_constraints_12000000 = { ++ .list = bcm2835_rates_12000000, ++ .count = ARRAY_SIZE(bcm2835_rates_12000000), ++}; ++ ++static int snd_audioinjector_pi_soundcard_startup(struct snd_pcm_substream *substream) ++{ ++ /* Setup constraints, because there is a 12 MHz XTAL on the board */ ++ snd_pcm_hw_constraint_list(substream->runtime, 0, ++ SNDRV_PCM_HW_PARAM_RATE, ++ &bcm2835_constraints_12000000); ++ return 0; ++} ++ ++static int snd_audioinjector_pi_soundcard_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0); ++ ++ switch (params_rate(params)){ ++ case 8000: ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, 1); ++ case 16000: ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, 750); ++ case 32000: ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, 375); ++ case 44100: ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, 272); ++ case 48000: ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, 250); ++ case 88200: ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, 136); ++ case 96000: ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, 125); ++ default: ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, 125); ++ } ++} ++ ++/* machine stream operations */ ++static struct snd_soc_ops snd_audioinjector_pi_soundcard_ops = { ++ .startup = snd_audioinjector_pi_soundcard_startup, ++ .hw_params = snd_audioinjector_pi_soundcard_hw_params, ++}; ++ ++static int audioinjector_pi_soundcard_dai_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ return snd_soc_dai_set_sysclk(asoc_rtd_to_codec(rtd, 0), WM8731_SYSCLK_XTAL, 12000000, SND_SOC_CLOCK_IN); ++} ++ ++SND_SOC_DAILINK_DEFS(audioinjector_pi, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("wm8731.1-001a", "wm8731-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2835-i2s.0"))); ++ ++static struct snd_soc_dai_link audioinjector_pi_soundcard_dai[] = { ++ { ++ .name = "AudioInjector audio", ++ .stream_name = "AudioInjector audio", ++ .ops = &snd_audioinjector_pi_soundcard_ops, ++ .init = audioinjector_pi_soundcard_dai_init, ++ .dai_fmt = SND_SOC_DAIFMT_CBM_CFM|SND_SOC_DAIFMT_I2S|SND_SOC_DAIFMT_NB_NF, ++ SND_SOC_DAILINK_REG(audioinjector_pi), ++ }, ++}; ++ ++static const struct snd_soc_dapm_widget wm8731_dapm_widgets[] = { ++ SND_SOC_DAPM_HP("Headphone Jack", NULL), ++ SND_SOC_DAPM_SPK("Ext Spk", NULL), ++ SND_SOC_DAPM_LINE("Line In Jacks", NULL), ++ SND_SOC_DAPM_MIC("Microphone", NULL), ++}; ++ ++static const struct snd_soc_dapm_route audioinjector_audio_map[] = { ++ /* headphone connected to LHPOUT, RHPOUT */ ++ {"Headphone Jack", NULL, "LHPOUT"}, ++ {"Headphone Jack", NULL, "RHPOUT"}, ++ ++ /* speaker connected to LOUT, ROUT */ ++ {"Ext Spk", NULL, "ROUT"}, ++ {"Ext Spk", NULL, "LOUT"}, ++ ++ /* line inputs */ ++ {"Line In Jacks", NULL, "Line Input"}, ++ ++ /* mic is connected to Mic Jack, with WM8731 Mic Bias */ ++ {"Microphone", NULL, "Mic Bias"}, ++}; ++ ++static struct snd_soc_card snd_soc_audioinjector = { ++ .name = "audioinjector-pi-soundcard", ++ .dai_link = audioinjector_pi_soundcard_dai, ++ .num_links = ARRAY_SIZE(audioinjector_pi_soundcard_dai), ++ ++ .dapm_widgets = wm8731_dapm_widgets, ++ .num_dapm_widgets = ARRAY_SIZE(wm8731_dapm_widgets), ++ .dapm_routes = audioinjector_audio_map, ++ .num_dapm_routes = ARRAY_SIZE(audioinjector_audio_map), ++}; ++ ++static int audioinjector_pi_soundcard_probe(struct platform_device *pdev) ++{ ++ struct snd_soc_card *card = &snd_soc_audioinjector; ++ int ret; ++ ++ card->dev = &pdev->dev; ++ ++ if (pdev->dev.of_node) { ++ struct snd_soc_dai_link *dai = &audioinjector_pi_soundcard_dai[0]; ++ struct device_node *i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ ++ if (i2s_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } else ++ if (!dai->cpus->of_node) { ++ dev_err(&pdev->dev, "Property 'i2s-controller' missing or invalid\n"); ++ return -EINVAL; ++ } ++ } ++ ++ if ((ret = devm_snd_soc_register_card(&pdev->dev, card))) { ++ dev_err(&pdev->dev, "snd_soc_register_card failed (%d)\n", ret); ++ } ++ return ret; ++} ++ ++static const struct of_device_id audioinjector_pi_soundcard_of_match[] = { ++ { .compatible = "ai,audioinjector-pi-soundcard", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, audioinjector_pi_soundcard_of_match); ++ ++static struct platform_driver audioinjector_pi_soundcard_driver = { ++ .driver = { ++ .name = "audioinjector-stereo", ++ .owner = THIS_MODULE, ++ .of_match_table = audioinjector_pi_soundcard_of_match, ++ }, ++ .probe = audioinjector_pi_soundcard_probe, ++}; ++ ++module_platform_driver(audioinjector_pi_soundcard_driver); ++MODULE_AUTHOR("Matt Flax "); ++MODULE_DESCRIPTION("AudioInjector.net Pi Soundcard"); ++MODULE_LICENSE("GPL v2"); ++MODULE_ALIAS("platform:audioinjector-pi-soundcard"); ++ +--- /dev/null ++++ b/sound/soc/bcm/audiosense-pi.c +@@ -0,0 +1,248 @@ ++/* ++ * ASoC Driver for AudioSense add on soundcard ++ * Author: ++ * Bhargav A K ++ * Copyright 2017 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include "../codecs/tlv320aic32x4.h" ++ ++#define AIC32X4_SYSCLK_XTAL 0x00 ++ ++/* ++ * Setup Codec Sample Rates and Channels ++ * Supported Rates: ++ * 8000, 11025, 16000, 22050, 32000, 44100, 48000, 64000, 88200, 96000, ++ */ ++static const unsigned int audiosense_pi_rate[] = { ++ 48000, ++}; ++ ++static struct snd_pcm_hw_constraint_list audiosense_constraints_rates = { ++ .list = audiosense_pi_rate, ++ .count = ARRAY_SIZE(audiosense_pi_rate), ++}; ++ ++static const unsigned int audiosense_pi_channels[] = { ++ 2, ++}; ++ ++static struct snd_pcm_hw_constraint_list audiosense_constraints_ch = { ++ .count = ARRAY_SIZE(audiosense_pi_channels), ++ .list = audiosense_pi_channels, ++ .mask = 0, ++}; ++ ++/* Setup DAPM widgets and paths */ ++static const struct snd_soc_dapm_widget audiosense_pi_dapm_widgets[] = { ++ SND_SOC_DAPM_HP("Headphone Jack", NULL), ++ SND_SOC_DAPM_LINE("Line Out", NULL), ++ SND_SOC_DAPM_LINE("Line In", NULL), ++ SND_SOC_DAPM_INPUT("CM_L"), ++ SND_SOC_DAPM_INPUT("CM_R"), ++}; ++ ++static const struct snd_soc_dapm_route audiosense_pi_audio_map[] = { ++ /* Line Inputs are connected to ++ * (IN1_L | IN1_R) ++ * (IN2_L | IN2_R) ++ * (IN3_L | IN3_R) ++ */ ++ {"IN1_L", NULL, "Line In"}, ++ {"IN1_R", NULL, "Line In"}, ++ {"IN2_L", NULL, "Line In"}, ++ {"IN2_R", NULL, "Line In"}, ++ {"IN3_L", NULL, "Line In"}, ++ {"IN3_R", NULL, "Line In"}, ++ ++ /* Mic is connected to IN2_L and IN2_R */ ++ {"Left ADC", NULL, "Mic Bias"}, ++ {"Right ADC", NULL, "Mic Bias"}, ++ ++ /* Headphone connected to HPL, HPR */ ++ {"Headphone Jack", NULL, "HPL"}, ++ {"Headphone Jack", NULL, "HPR"}, ++ ++ /* Speakers connected to LOL and LOR */ ++ {"Line Out", NULL, "LOL"}, ++ {"Line Out", NULL, "LOR"}, ++}; ++ ++static int audiosense_pi_card_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ /* TODO: init of the codec specific dapm data, ignore suspend/resume */ ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ ++ snd_soc_component_update_bits(component, AIC32X4_MICBIAS, 0x78, ++ AIC32X4_MICBIAS_LDOIN | ++ AIC32X4_MICBIAS_2075V); ++ snd_soc_component_update_bits(component, AIC32X4_PWRCFG, 0x08, ++ AIC32X4_AVDDWEAKDISABLE); ++ snd_soc_component_update_bits(component, AIC32X4_LDOCTL, 0x01, ++ AIC32X4_LDOCTLEN); ++ ++ return 0; ++} ++ ++static int audiosense_pi_card_hw_params( ++ struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params) ++{ ++ int ret = 0; ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_dai *codec_dai = asoc_rtd_to_codec(rtd, 0); ++ ++ /* Set the codec system clock, there is a 12 MHz XTAL on the board */ ++ ret = snd_soc_dai_set_sysclk(codec_dai, AIC32X4_SYSCLK_XTAL, ++ 12000000, SND_SOC_CLOCK_IN); ++ if (ret) { ++ dev_err(rtd->card->dev, ++ "could not set codec driver clock params\n"); ++ return ret; ++ } ++ return 0; ++} ++ ++static int audiosense_pi_card_startup(struct snd_pcm_substream *substream) ++{ ++ struct snd_pcm_runtime *runtime = substream->runtime; ++ ++ /* ++ * Set codec to 48Khz Sampling, Stereo I/O and 16 bit audio ++ */ ++ runtime->hw.channels_max = 2; ++ snd_pcm_hw_constraint_list(runtime, 0, SNDRV_PCM_HW_PARAM_CHANNELS, ++ &audiosense_constraints_ch); ++ ++ runtime->hw.formats = SNDRV_PCM_FMTBIT_S16_LE; ++ snd_pcm_hw_constraint_msbits(runtime, 0, 16, 16); ++ ++ ++ snd_pcm_hw_constraint_list(substream->runtime, 0, ++ SNDRV_PCM_HW_PARAM_RATE, ++ &audiosense_constraints_rates); ++ return 0; ++} ++ ++static struct snd_soc_ops audiosense_pi_card_ops = { ++ .startup = audiosense_pi_card_startup, ++ .hw_params = audiosense_pi_card_hw_params, ++}; ++ ++SND_SOC_DAILINK_DEFS(audiosense_pi, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("tlv320aic32x4.1-0018", "tlv320aic32x4-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link audiosense_pi_card_dai[] = { ++ { ++ .name = "TLV320AIC3204 Audio", ++ .stream_name = "TLV320AIC3204 Hifi Audio", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBM_CFM, ++ .ops = &audiosense_pi_card_ops, ++ .init = audiosense_pi_card_init, ++ SND_SOC_DAILINK_REG(audiosense_pi), ++ }, ++}; ++ ++static struct snd_soc_card audiosense_pi_card = { ++ .name = "audiosense-pi", ++ .driver_name = "audiosense-pi", ++ .dai_link = audiosense_pi_card_dai, ++ .owner = THIS_MODULE, ++ .num_links = ARRAY_SIZE(audiosense_pi_card_dai), ++ .dapm_widgets = audiosense_pi_dapm_widgets, ++ .num_dapm_widgets = ARRAY_SIZE(audiosense_pi_dapm_widgets), ++ .dapm_routes = audiosense_pi_audio_map, ++ .num_dapm_routes = ARRAY_SIZE(audiosense_pi_audio_map), ++}; ++ ++static int audiosense_pi_card_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ struct snd_soc_card *card = &audiosense_pi_card; ++ struct snd_soc_dai_link *dai = &audiosense_pi_card_dai[0]; ++ struct device_node *i2s_node = pdev->dev.of_node; ++ ++ card->dev = &pdev->dev; ++ ++ if (!dai) { ++ dev_err(&pdev->dev, "DAI not found. Missing or Invalid\n"); ++ return -EINVAL; ++ } ++ ++ i2s_node = of_parse_phandle(pdev->dev.of_node, "i2s-controller", 0); ++ if (!i2s_node) { ++ dev_err(&pdev->dev, ++ "Property 'i2s-controller' missing or invalid\n"); ++ return -EINVAL; ++ } ++ ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ ++ of_node_put(i2s_node); ++ ++ ret = snd_soc_register_card(card); ++ if (ret && ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ ++ return ret; ++} ++ ++static int audiosense_pi_card_remove(struct platform_device *pdev) ++{ ++ struct snd_soc_card *card = platform_get_drvdata(pdev); ++ ++ return snd_soc_unregister_card(card); ++ ++} ++ ++static const struct of_device_id audiosense_pi_card_of_match[] = { ++ { .compatible = "as,audiosense-pi", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, audiosense_pi_card_of_match); ++ ++static struct platform_driver audiosense_pi_card_driver = { ++ .driver = { ++ .name = "audiosense-snd-card", ++ .owner = THIS_MODULE, ++ .of_match_table = audiosense_pi_card_of_match, ++ }, ++ .probe = audiosense_pi_card_probe, ++ .remove = audiosense_pi_card_remove, ++}; ++ ++module_platform_driver(audiosense_pi_card_driver); ++ ++MODULE_AUTHOR("Bhargav AK "); ++MODULE_DESCRIPTION("ASoC Driver for TLV320AIC3204 Audio"); ++MODULE_LICENSE("GPL v2"); ++MODULE_ALIAS("platform:audiosense-pi"); ++ +--- /dev/null ++++ b/sound/soc/bcm/digidac1-soundcard.c +@@ -0,0 +1,421 @@ ++/* ++ * ASoC Driver for RRA DigiDAC1 ++ * Copyright 2016 ++ * Author: José M. Tasende ++ * based on the HifiBerry DAC driver by Florian Meier ++ * and the Wolfson card driver by Nikesh Oswal, ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "../codecs/wm8804.h" ++#include "../codecs/wm8741.h" ++ ++#define WM8741_NUM_SUPPLIES 2 ++ ++/* codec private data */ ++struct wm8741_priv { ++ struct wm8741_platform_data pdata; ++ struct regmap *regmap; ++ struct regulator_bulk_data supplies[WM8741_NUM_SUPPLIES]; ++ unsigned int sysclk; ++ const struct snd_pcm_hw_constraint_list *sysclk_constraints; ++}; ++ ++static int samplerate = 44100; ++ ++/* New Alsa Controls not exposed by original wm8741 codec driver */ ++/* in actual driver the att. adjustment is wrong because */ ++/* this DAC has a coarse attenuation register with 4dB steps */ ++/* and a fine level register with 0.125dB steps */ ++/* each register has 32 steps so combining both we have 1024 steps */ ++/* of 0.125 dB. */ ++/* The original level controls from driver are removed at startup */ ++/* and replaced by the corrected ones. */ ++/* The same wm8741 driver can be used for wm8741 and wm8742 devices */ ++ ++static const DECLARE_TLV_DB_SCALE(dac_tlv_fine, 0, 13, 0); ++static const DECLARE_TLV_DB_SCALE(dac_tlv_coarse, -12700, 400, 1); ++static const char *w8741_dither[4] = {"Off", "RPDF", "TPDF", "HPDF"}; ++static const char *w8741_filter[5] = { ++ "Type 1", "Type 2", "Type 3", "Type 4", "Type 5"}; ++static const char *w8741_switch[2] = {"Off", "On"}; ++static const struct soc_enum w8741_enum[] = { ++SOC_ENUM_SINGLE(WM8741_MODE_CONTROL_2, 0, 4, w8741_dither),/* dithering type */ ++SOC_ENUM_SINGLE(WM8741_FILTER_CONTROL, 0, 5, w8741_filter),/* filter type */ ++SOC_ENUM_SINGLE(WM8741_FORMAT_CONTROL, 6, 2, w8741_switch),/* phase invert */ ++SOC_ENUM_SINGLE(WM8741_VOLUME_CONTROL, 0, 2, w8741_switch),/* volume ramp */ ++SOC_ENUM_SINGLE(WM8741_VOLUME_CONTROL, 3, 2, w8741_switch),/* soft mute */ ++}; ++ ++static const struct snd_kcontrol_new w8741_snd_controls_stereo[] = { ++SOC_DOUBLE_R_TLV("DAC Fine Playback Volume", WM8741_DACLLSB_ATTENUATION, ++ WM8741_DACRLSB_ATTENUATION, 0, 31, 1, dac_tlv_fine), ++SOC_DOUBLE_R_TLV("Digital Playback Volume", WM8741_DACLMSB_ATTENUATION, ++ WM8741_DACRMSB_ATTENUATION, 0, 31, 1, dac_tlv_coarse), ++SOC_ENUM("DAC Dither", w8741_enum[0]), ++SOC_ENUM("DAC Digital Filter", w8741_enum[1]), ++SOC_ENUM("DAC Phase Invert", w8741_enum[2]), ++SOC_ENUM("DAC Volume Ramp", w8741_enum[3]), ++SOC_ENUM("DAC Soft Mute", w8741_enum[4]), ++}; ++ ++static const struct snd_kcontrol_new w8741_snd_controls_mono_left[] = { ++SOC_SINGLE_TLV("DAC Fine Playback Volume", WM8741_DACLLSB_ATTENUATION, ++ 0, 31, 0, dac_tlv_fine), ++SOC_SINGLE_TLV("Digital Playback Volume", WM8741_DACLMSB_ATTENUATION, ++ 0, 31, 1, dac_tlv_coarse), ++SOC_ENUM("DAC Dither", w8741_enum[0]), ++SOC_ENUM("DAC Digital Filter", w8741_enum[1]), ++SOC_ENUM("DAC Phase Invert", w8741_enum[2]), ++SOC_ENUM("DAC Volume Ramp", w8741_enum[3]), ++SOC_ENUM("DAC Soft Mute", w8741_enum[4]), ++}; ++ ++static const struct snd_kcontrol_new w8741_snd_controls_mono_right[] = { ++SOC_SINGLE_TLV("DAC Fine Playback Volume", WM8741_DACRLSB_ATTENUATION, ++ 0, 31, 0, dac_tlv_fine), ++SOC_SINGLE_TLV("Digital Playback Volume", WM8741_DACRMSB_ATTENUATION, ++ 0, 31, 1, dac_tlv_coarse), ++SOC_ENUM("DAC Dither", w8741_enum[0]), ++SOC_ENUM("DAC Digital Filter", w8741_enum[1]), ++SOC_ENUM("DAC Phase Invert", w8741_enum[2]), ++SOC_ENUM("DAC Volume Ramp", w8741_enum[3]), ++SOC_ENUM("DAC Soft Mute", w8741_enum[4]), ++}; ++ ++static int w8741_add_controls(struct snd_soc_component *component) ++{ ++ struct wm8741_priv *wm8741 = snd_soc_component_get_drvdata(component); ++ ++ switch (wm8741->pdata.diff_mode) { ++ case WM8741_DIFF_MODE_STEREO: ++ case WM8741_DIFF_MODE_STEREO_REVERSED: ++ snd_soc_add_component_controls(component, ++ w8741_snd_controls_stereo, ++ ARRAY_SIZE(w8741_snd_controls_stereo)); ++ break; ++ case WM8741_DIFF_MODE_MONO_LEFT: ++ snd_soc_add_component_controls(component, ++ w8741_snd_controls_mono_left, ++ ARRAY_SIZE(w8741_snd_controls_mono_left)); ++ break; ++ case WM8741_DIFF_MODE_MONO_RIGHT: ++ snd_soc_add_component_controls(component, ++ w8741_snd_controls_mono_right, ++ ARRAY_SIZE(w8741_snd_controls_mono_right)); ++ break; ++ default: ++ return -EINVAL; ++ } ++ ++ return 0; ++} ++ ++static int digidac1_soundcard_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_card *card = rtd->card; ++ struct snd_soc_pcm_runtime *wm8741_rtd; ++ struct snd_soc_component *wm8741_component; ++ struct snd_card *sound_card = card->snd_card; ++ struct snd_kcontrol *kctl; ++ int ret; ++ ++ wm8741_rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[1]); ++ if (!wm8741_rtd) { ++ dev_warn(card->dev, "digidac1_soundcard_init: couldn't get wm8741 rtd\n"); ++ return -EFAULT; ++ } ++ wm8741_component = asoc_rtd_to_codec(wm8741_rtd, 0)->component; ++ ret = w8741_add_controls(wm8741_component); ++ if (ret < 0) ++ dev_warn(card->dev, "Failed to add new wm8741 controls: %d\n", ++ ret); ++ ++ /* enable TX output */ ++ snd_soc_component_update_bits(component, WM8804_PWRDN, 0x4, 0x0); ++ ++ kctl = snd_soc_card_get_kcontrol(card, ++ "Playback Volume"); ++ if (kctl) { ++ kctl->vd[0].access = SNDRV_CTL_ELEM_ACCESS_READWRITE; ++ snd_ctl_remove(sound_card, kctl); ++ } ++ kctl = snd_soc_card_get_kcontrol(card, ++ "Fine Playback Volume"); ++ if (kctl) { ++ kctl->vd[0].access = SNDRV_CTL_ELEM_ACCESS_READWRITE; ++ snd_ctl_remove(sound_card, kctl); ++ } ++ return 0; ++} ++ ++static int digidac1_soundcard_startup(struct snd_pcm_substream *substream) ++{ ++ /* turn on wm8804 digital output */ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_card *card = rtd->card; ++ struct snd_soc_pcm_runtime *wm8741_rtd; ++ struct snd_soc_component *wm8741_component; ++ ++ snd_soc_component_update_bits(component, WM8804_PWRDN, 0x3c, 0x00); ++ wm8741_rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[1]); ++ if (!wm8741_rtd) { ++ dev_warn(card->dev, "digidac1_soundcard_startup: couldn't get WM8741 rtd\n"); ++ return -EFAULT; ++ } ++ wm8741_component = asoc_rtd_to_codec(wm8741_rtd, 0)->component; ++ ++ /* latch wm8741 level */ ++ snd_soc_component_update_bits(wm8741_component, WM8741_DACLLSB_ATTENUATION, ++ WM8741_UPDATELL, WM8741_UPDATELL); ++ snd_soc_component_update_bits(wm8741_component, WM8741_DACLMSB_ATTENUATION, ++ WM8741_UPDATELM, WM8741_UPDATELM); ++ snd_soc_component_update_bits(wm8741_component, WM8741_DACRLSB_ATTENUATION, ++ WM8741_UPDATERL, WM8741_UPDATERL); ++ snd_soc_component_update_bits(wm8741_component, WM8741_DACRMSB_ATTENUATION, ++ WM8741_UPDATERM, WM8741_UPDATERM); ++ ++ return 0; ++} ++ ++static void digidac1_soundcard_shutdown(struct snd_pcm_substream *substream) ++{ ++ /* turn off wm8804 digital output */ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ ++ snd_soc_component_update_bits(component, WM8804_PWRDN, 0x3c, 0x3c); ++} ++ ++static int digidac1_soundcard_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_dai *codec_dai = asoc_rtd_to_codec(rtd, 0); ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0); ++ struct snd_soc_card *card = rtd->card; ++ struct snd_soc_pcm_runtime *wm8741_rtd; ++ struct snd_soc_component *wm8741_component; ++ ++ int sysclk = 27000000; ++ long mclk_freq = 0; ++ int mclk_div = 1; ++ int sampling_freq = 1; ++ int ret; ++ ++ wm8741_rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[1]); ++ if (!wm8741_rtd) { ++ dev_warn(card->dev, "digidac1_soundcard_hw_params: couldn't get WM8741 rtd\n"); ++ return -EFAULT; ++ } ++ wm8741_component = asoc_rtd_to_codec(wm8741_rtd, 0)->component; ++ samplerate = params_rate(params); ++ ++ if (samplerate <= 96000) { ++ mclk_freq = samplerate*256; ++ mclk_div = WM8804_MCLKDIV_256FS; ++ } else { ++ mclk_freq = samplerate*128; ++ mclk_div = WM8804_MCLKDIV_128FS; ++ } ++ ++ switch (samplerate) { ++ case 32000: ++ sampling_freq = 0x03; ++ break; ++ case 44100: ++ sampling_freq = 0x00; ++ break; ++ case 48000: ++ sampling_freq = 0x02; ++ break; ++ case 88200: ++ sampling_freq = 0x08; ++ break; ++ case 96000: ++ sampling_freq = 0x0a; ++ break; ++ case 176400: ++ sampling_freq = 0x0c; ++ break; ++ case 192000: ++ sampling_freq = 0x0e; ++ break; ++ default: ++ dev_err(card->dev, ++ "Failed to set WM8804 SYSCLK, unsupported samplerate %d\n", ++ samplerate); ++ } ++ ++ snd_soc_dai_set_clkdiv(codec_dai, WM8804_MCLK_DIV, mclk_div); ++ snd_soc_dai_set_pll(codec_dai, 0, 0, sysclk, mclk_freq); ++ ++ ret = snd_soc_dai_set_sysclk(codec_dai, WM8804_TX_CLKSRC_PLL, ++ sysclk, SND_SOC_CLOCK_OUT); ++ if (ret < 0) { ++ dev_err(card->dev, ++ "Failed to set WM8804 SYSCLK: %d\n", ret); ++ return ret; ++ } ++ /* Enable wm8804 TX output */ ++ snd_soc_component_update_bits(component, WM8804_PWRDN, 0x4, 0x0); ++ ++ /* wm8804 Power on */ ++ snd_soc_component_update_bits(component, WM8804_PWRDN, 0x9, 0); ++ ++ /* wm8804 set sampling frequency status bits */ ++ snd_soc_component_update_bits(component, WM8804_SPDTX4, 0x0f, sampling_freq); ++ ++ /* Now update wm8741 registers for the correct oversampling */ ++ if (samplerate <= 48000) ++ snd_soc_component_update_bits(wm8741_component, WM8741_MODE_CONTROL_1, ++ WM8741_OSR_MASK, 0x00); ++ else if (samplerate <= 96000) ++ snd_soc_component_update_bits(wm8741_component, WM8741_MODE_CONTROL_1, ++ WM8741_OSR_MASK, 0x20); ++ else ++ snd_soc_component_update_bits(wm8741_component, WM8741_MODE_CONTROL_1, ++ WM8741_OSR_MASK, 0x40); ++ ++ /* wm8741 bit size */ ++ switch (params_width(params)) { ++ case 16: ++ snd_soc_component_update_bits(wm8741_component, WM8741_FORMAT_CONTROL, ++ WM8741_IWL_MASK, 0x00); ++ break; ++ case 20: ++ snd_soc_component_update_bits(wm8741_component, WM8741_FORMAT_CONTROL, ++ WM8741_IWL_MASK, 0x01); ++ break; ++ case 24: ++ snd_soc_component_update_bits(wm8741_component, WM8741_FORMAT_CONTROL, ++ WM8741_IWL_MASK, 0x02); ++ break; ++ case 32: ++ snd_soc_component_update_bits(wm8741_component, WM8741_FORMAT_CONTROL, ++ WM8741_IWL_MASK, 0x03); ++ break; ++ default: ++ dev_dbg(card->dev, "wm8741_hw_params: Unsupported bit size param = %d", ++ params_width(params)); ++ return -EINVAL; ++ } ++ ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, 64); ++} ++/* machine stream operations */ ++static struct snd_soc_ops digidac1_soundcard_ops = { ++ .hw_params = digidac1_soundcard_hw_params, ++ .startup = digidac1_soundcard_startup, ++ .shutdown = digidac1_soundcard_shutdown, ++}; ++ ++SND_SOC_DAILINK_DEFS(digidac1, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("wm8804.1-003b", "wm8804-spdif")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2835-i2s.0"))); ++ ++SND_SOC_DAILINK_DEFS(digidac11, ++ DAILINK_COMP_ARRAY(COMP_CPU("wm8804-spdif")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("wm8741.1-001a", "wm8741")), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++static struct snd_soc_dai_link digidac1_soundcard_dai[] = { ++ { ++ .name = "RRA DigiDAC1", ++ .stream_name = "RRA DigiDAC1 HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBM_CFM, ++ .ops = &digidac1_soundcard_ops, ++ .init = digidac1_soundcard_init, ++ SND_SOC_DAILINK_REG(digidac1), ++ }, ++ { ++ .name = "RRA DigiDAC11", ++ .stream_name = "RRA DigiDAC11 HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S ++ | SND_SOC_DAIFMT_NB_NF ++ | SND_SOC_DAIFMT_CBS_CFS, ++ SND_SOC_DAILINK_REG(digidac11), ++ }, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card digidac1_soundcard = { ++ .name = "digidac1-soundcard", ++ .owner = THIS_MODULE, ++ .dai_link = digidac1_soundcard_dai, ++ .num_links = ARRAY_SIZE(digidac1_soundcard_dai), ++}; ++ ++static int digidac1_soundcard_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ ++ digidac1_soundcard.dev = &pdev->dev; ++ ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai = &digidac1_soundcard_dai[0]; ++ ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ ++ if (i2s_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } ++ } ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, &digidac1_soundcard); ++ if (ret && ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n", ++ ret); ++ ++ return ret; ++} ++ ++static const struct of_device_id digidac1_soundcard_of_match[] = { ++ { .compatible = "rra,digidac1-soundcard", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, digidac1_soundcard_of_match); ++ ++static struct platform_driver digidac1_soundcard_driver = { ++ .driver = { ++ .name = "digidac1-audio", ++ .owner = THIS_MODULE, ++ .of_match_table = digidac1_soundcard_of_match, ++ }, ++ .probe = digidac1_soundcard_probe, ++}; ++ ++module_platform_driver(digidac1_soundcard_driver); ++ ++MODULE_AUTHOR("José M. Tasende "); ++MODULE_DESCRIPTION("ASoC Driver for RRA DigiDAC1"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/dionaudio_loco-v2.c +@@ -0,0 +1,117 @@ ++/* ++ * ASoC Driver for Dion Audio LOCO-V2 DAC-AMP ++ * ++ * Author: Miquel Blauw ++ * Copyright 2017 ++ * ++ * Based on the software of the RPi-DAC writen by Florian Meier ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++ ++static bool digital_gain_0db_limit = true; ++ ++static int snd_rpi_dionaudio_loco_v2_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ if (digital_gain_0db_limit) { ++ int ret; ++ struct snd_soc_card *card = rtd->card; ++ ++ ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207); ++ if (ret < 0) ++ dev_warn(card->dev, "Failed to set volume limit: %d\n", ret); ++ } ++ ++ return 0; ++} ++ ++SND_SOC_DAILINK_DEFS(dionaudio_loco_v2, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("pcm512x.1-004d", "pcm512x-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_rpi_dionaudio_loco_v2_dai[] = { ++{ ++ .name = "DionAudio LOCO-V2", ++ .stream_name = "DionAudio LOCO-V2 DAC-AMP", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ .init = snd_rpi_dionaudio_loco_v2_init, ++ SND_SOC_DAILINK_REG(dionaudio_loco_v2), ++},}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_rpi_dionaudio_loco_v2 = { ++ .name = "Dion Audio LOCO-V2", ++ .dai_link = snd_rpi_dionaudio_loco_v2_dai, ++ .num_links = ARRAY_SIZE(snd_rpi_dionaudio_loco_v2_dai), ++}; ++ ++static int snd_rpi_dionaudio_loco_v2_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ ++ snd_rpi_dionaudio_loco_v2.dev = &pdev->dev; ++ ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai = ++ &snd_rpi_dionaudio_loco_v2_dai[0]; ++ ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ if (i2s_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } ++ ++ digital_gain_0db_limit = !of_property_read_bool( ++ pdev->dev.of_node, "dionaudio,24db_digital_gain"); ++ } ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, &snd_rpi_dionaudio_loco_v2); ++ if (ret) ++ dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n", ++ ret); ++ ++ return ret; ++} ++ ++static const struct of_device_id dionaudio_of_match[] = { ++ { .compatible = "dionaudio,dionaudio-loco-v2", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, dionaudio_of_match); ++ ++static struct platform_driver snd_rpi_dionaudio_loco_v2_driver = { ++ .driver = { ++ .name = "snd-rpi-dionaudio-loco-v2", ++ .owner = THIS_MODULE, ++ .of_match_table = dionaudio_of_match, ++ }, ++ .probe = snd_rpi_dionaudio_loco_v2_probe, ++}; ++ ++module_platform_driver(snd_rpi_dionaudio_loco_v2_driver); ++ ++MODULE_AUTHOR("Miquel Blauw "); ++MODULE_DESCRIPTION("ASoC Driver for DionAudio LOCO-V2"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/dionaudio_loco.c +@@ -0,0 +1,117 @@ ++/* ++ * ASoC Driver for Dion Audio LOCO DAC-AMP ++ * ++ * Author: Miquel Blauw ++ * Copyright 2016 ++ * ++ * Based on the software of the RPi-DAC writen by Florian Meier ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++ ++static int snd_rpi_dionaudio_loco_hw_params( ++ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0); ++ ++ unsigned int sample_bits = ++ snd_pcm_format_physical_width(params_format(params)); ++ ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2); ++} ++ ++/* machine stream operations */ ++static struct snd_soc_ops snd_rpi_dionaudio_loco_ops = { ++ .hw_params = snd_rpi_dionaudio_loco_hw_params, ++}; ++ ++SND_SOC_DAILINK_DEFS(dionaudio_loco, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("pcm5102a-codec", "pcm5102a-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_rpi_dionaudio_loco_dai[] = { ++{ ++ .name = "DionAudio LOCO", ++ .stream_name = "DionAudio LOCO DAC-AMP", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | ++ SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ .ops = &snd_rpi_dionaudio_loco_ops, ++ SND_SOC_DAILINK_REG(dionaudio_loco), ++}, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_rpi_dionaudio_loco = { ++ .name = "snd_rpi_dionaudio_loco", ++ .dai_link = snd_rpi_dionaudio_loco_dai, ++ .num_links = ARRAY_SIZE(snd_rpi_dionaudio_loco_dai), ++}; ++ ++static int snd_rpi_dionaudio_loco_probe(struct platform_device *pdev) ++{ ++ struct device_node *np; ++ int ret = 0; ++ ++ snd_rpi_dionaudio_loco.dev = &pdev->dev; ++ ++ np = pdev->dev.of_node; ++ if (np) { ++ struct snd_soc_dai_link *dai = &snd_rpi_dionaudio_loco_dai[0]; ++ struct device_node *i2s_np; ++ ++ i2s_np = of_parse_phandle(np, "i2s-controller", 0); ++ if (i2s_np) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_np; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_np; ++ } ++ } ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, &snd_rpi_dionaudio_loco); ++ if (ret && ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n", ++ ret); ++ ++ return ret; ++} ++ ++static const struct of_device_id snd_rpi_dionaudio_loco_of_match[] = { ++ { .compatible = "dionaudio,loco-pcm5242-tpa3118", }, ++ { /* sentinel */ }, ++}; ++MODULE_DEVICE_TABLE(of, snd_rpi_dionaudio_loco_of_match); ++ ++static struct platform_driver snd_rpi_dionaudio_loco_driver = { ++ .driver = { ++ .name = "snd-dionaudio-loco", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_rpi_dionaudio_loco_of_match, ++ }, ++ .probe = snd_rpi_dionaudio_loco_probe, ++}; ++ ++module_platform_driver(snd_rpi_dionaudio_loco_driver); ++ ++MODULE_AUTHOR("Miquel Blauw "); ++MODULE_DESCRIPTION("ASoC Driver for DionAudio LOCO"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/fe-pi-audio.c +@@ -0,0 +1,154 @@ ++/* ++ * ASoC Driver for Fe-Pi Audio Sound Card ++ * ++ * Author: Henry Kupis ++ * Copyright 2016 ++ * based on code by Florian Meier ++ * based on code by Shawn Guo ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++ ++#include "../codecs/sgtl5000.h" ++ ++static int snd_fe_pi_audio_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_card *card = rtd->card; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ ++ snd_soc_dapm_force_enable_pin(&card->dapm, "LO"); ++ snd_soc_dapm_force_enable_pin(&card->dapm, "ADC"); ++ snd_soc_dapm_force_enable_pin(&card->dapm, "DAC"); ++ snd_soc_dapm_force_enable_pin(&card->dapm, "HP"); ++ snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER, ++ SGTL5000_VAG_POWERUP, SGTL5000_VAG_POWERUP); ++ ++ return 0; ++} ++ ++static int snd_fe_pi_audio_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct device *dev = rtd->card->dev; ++ struct snd_soc_dai *codec_dai = asoc_rtd_to_codec(rtd, 0); ++ ++ int ret; ++ ++ /* Set SGTL5000's SYSCLK */ ++ ret = snd_soc_dai_set_sysclk(codec_dai, SGTL5000_SYSCLK, 12288000, SND_SOC_CLOCK_IN); ++ if (ret) { ++ dev_err(dev, "could not set codec driver clock params\n"); ++ return ret; ++ } ++ ++ return 0; ++} ++ ++ ++static struct snd_soc_ops snd_fe_pi_audio_ops = { ++ .hw_params = snd_fe_pi_audio_hw_params, ++}; ++ ++SND_SOC_DAILINK_DEFS(fe_pi, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("sgtl5000.1-000a", "sgtl5000")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_fe_pi_audio_dai[] = { ++ { ++ .name = "FE-PI", ++ .stream_name = "Fe-Pi HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBM_CFM, ++ .ops = &snd_fe_pi_audio_ops, ++ .init = snd_fe_pi_audio_init, ++ SND_SOC_DAILINK_REG(fe_pi), ++ }, ++}; ++ ++static const struct snd_soc_dapm_route fe_pi_audio_dapm_routes[] = { ++ {"ADC", NULL, "Mic Bias"}, ++}; ++ ++ ++static struct snd_soc_card fe_pi_audio = { ++ .name = "Fe-Pi Audio", ++ .owner = THIS_MODULE, ++ .dai_link = snd_fe_pi_audio_dai, ++ .num_links = ARRAY_SIZE(snd_fe_pi_audio_dai), ++ ++ .dapm_routes = fe_pi_audio_dapm_routes, ++ .num_dapm_routes = ARRAY_SIZE(fe_pi_audio_dapm_routes), ++}; ++ ++static int snd_fe_pi_audio_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ struct snd_soc_card *card = &fe_pi_audio; ++ struct device_node *np = pdev->dev.of_node; ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai = &snd_fe_pi_audio_dai[0]; ++ ++ fe_pi_audio.dev = &pdev->dev; ++ ++ i2s_node = of_parse_phandle(np, "i2s-controller", 0); ++ if (!i2s_node) { ++ dev_err(&pdev->dev, "i2s_node phandle missing or invalid\n"); ++ return -EINVAL; ++ } ++ ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ ++ of_node_put(i2s_node); ++ ++ card->dev = &pdev->dev; ++ platform_set_drvdata(pdev, card); ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, card); ++ if (ret && ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, "snd_soc_register_card() failed: %d\n", ret); ++ ++ return ret; ++} ++ ++static const struct of_device_id snd_fe_pi_audio_of_match[] = { ++ { .compatible = "fe-pi,fe-pi-audio", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, snd_fe_pi_audio_of_match); ++ ++static struct platform_driver snd_fe_pi_audio_driver = { ++ .driver = { ++ .name = "snd-fe-pi-audio", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_fe_pi_audio_of_match, ++ }, ++ .probe = snd_fe_pi_audio_probe, ++}; ++ ++module_platform_driver(snd_fe_pi_audio_driver); ++ ++MODULE_AUTHOR("Henry Kupis "); ++MODULE_DESCRIPTION("ASoC Driver for Fe-Pi Audio"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/googlevoicehat-codec.c +@@ -0,0 +1,214 @@ ++/* ++ * Driver for the Google voiceHAT audio codec for Raspberry Pi. ++ * ++ * Author: Peter Malkin ++ * Copyright 2016 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define ICS43432_RATE_MIN_HZ 7190 /* from data sheet */ ++#define ICS43432_RATE_MAX_HZ 52800 /* from data sheet */ ++/* Delay in enabling SDMODE after clock settles to remove pop */ ++#define SDMODE_DELAY_MS 5 ++ ++struct voicehat_priv { ++ struct delayed_work enable_sdmode_work; ++ struct gpio_desc *sdmode_gpio; ++ unsigned long sdmode_delay_jiffies; ++}; ++ ++static void voicehat_enable_sdmode_work(struct work_struct *work) ++{ ++ struct voicehat_priv *voicehat = container_of(work, ++ struct voicehat_priv, ++ enable_sdmode_work.work); ++ gpiod_set_value(voicehat->sdmode_gpio, 1); ++} ++ ++static int voicehat_component_probe(struct snd_soc_component *component) ++{ ++ struct voicehat_priv *voicehat = ++ snd_soc_component_get_drvdata(component); ++ ++ voicehat->sdmode_gpio = devm_gpiod_get(component->dev, "sdmode", ++ GPIOD_OUT_LOW); ++ if (IS_ERR(voicehat->sdmode_gpio)) { ++ dev_err(component->dev, "Unable to allocate GPIO pin\n"); ++ return PTR_ERR(voicehat->sdmode_gpio); ++ } ++ ++ INIT_DELAYED_WORK(&voicehat->enable_sdmode_work, ++ voicehat_enable_sdmode_work); ++ return 0; ++} ++ ++static void voicehat_component_remove(struct snd_soc_component *component) ++{ ++ struct voicehat_priv *voicehat = ++ snd_soc_component_get_drvdata(component); ++ ++ cancel_delayed_work_sync(&voicehat->enable_sdmode_work); ++} ++ ++static const struct snd_soc_dapm_widget voicehat_dapm_widgets[] = { ++ SND_SOC_DAPM_OUTPUT("Speaker"), ++}; ++ ++static const struct snd_soc_dapm_route voicehat_dapm_routes[] = { ++ {"Speaker", NULL, "HiFi Playback"}, ++}; ++ ++static const struct snd_soc_component_driver voicehat_component_driver = { ++ .probe = voicehat_component_probe, ++ .remove = voicehat_component_remove, ++ .dapm_widgets = voicehat_dapm_widgets, ++ .num_dapm_widgets = ARRAY_SIZE(voicehat_dapm_widgets), ++ .dapm_routes = voicehat_dapm_routes, ++ .num_dapm_routes = ARRAY_SIZE(voicehat_dapm_routes), ++}; ++ ++static int voicehat_daiops_trigger(struct snd_pcm_substream *substream, int cmd, ++ struct snd_soc_dai *dai) ++{ ++ struct snd_soc_component *component = dai->component; ++ struct voicehat_priv *voicehat = ++ snd_soc_component_get_drvdata(component); ++ ++ if (voicehat->sdmode_delay_jiffies == 0) ++ return 0; ++ ++ dev_dbg(dai->dev, "CMD %d", cmd); ++ dev_dbg(dai->dev, "Playback Active %d", dai->stream_active[SNDRV_PCM_STREAM_PLAYBACK]); ++ dev_dbg(dai->dev, "Capture Active %d", dai->stream_active[SNDRV_PCM_STREAM_CAPTURE]); ++ ++ switch (cmd) { ++ case SNDRV_PCM_TRIGGER_START: ++ case SNDRV_PCM_TRIGGER_RESUME: ++ case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: ++ if (dai->stream_active[SNDRV_PCM_STREAM_PLAYBACK]) { ++ dev_info(dai->dev, "Enabling audio amp...\n"); ++ queue_delayed_work( ++ system_power_efficient_wq, ++ &voicehat->enable_sdmode_work, ++ voicehat->sdmode_delay_jiffies); ++ } ++ break; ++ case SNDRV_PCM_TRIGGER_STOP: ++ case SNDRV_PCM_TRIGGER_SUSPEND: ++ case SNDRV_PCM_TRIGGER_PAUSE_PUSH: ++ if (dai->stream_active[SNDRV_PCM_STREAM_PLAYBACK]) { ++ cancel_delayed_work(&voicehat->enable_sdmode_work); ++ dev_info(dai->dev, "Disabling audio amp...\n"); ++ gpiod_set_value(voicehat->sdmode_gpio, 0); ++ } ++ break; ++ } ++ return 0; ++} ++ ++static const struct snd_soc_dai_ops voicehat_dai_ops = { ++ .trigger = voicehat_daiops_trigger, ++}; ++ ++static struct snd_soc_dai_driver voicehat_dai = { ++ .name = "voicehat-hifi", ++ .capture = { ++ .stream_name = "HiFi Capture", ++ .channels_min = 2, ++ .channels_max = 2, ++ .rates = SNDRV_PCM_RATE_48000, ++ .formats = SNDRV_PCM_FMTBIT_S32_LE ++ }, ++ .playback = { ++ .stream_name = "HiFi Playback", ++ .channels_min = 2, ++ .channels_max = 2, ++ .rates = SNDRV_PCM_RATE_48000, ++ .formats = SNDRV_PCM_FMTBIT_S32_LE ++ }, ++ .ops = &voicehat_dai_ops, ++ .symmetric_rates = 1 ++}; ++ ++#ifdef CONFIG_OF ++static const struct of_device_id voicehat_ids[] = { ++ { .compatible = "google,voicehat", }, {} ++ }; ++ MODULE_DEVICE_TABLE(of, voicehat_ids); ++#endif ++ ++static int voicehat_platform_probe(struct platform_device *pdev) ++{ ++ struct voicehat_priv *voicehat; ++ unsigned int sdmode_delay; ++ int ret; ++ ++ voicehat = devm_kzalloc(&pdev->dev, sizeof(*voicehat), GFP_KERNEL); ++ if (!voicehat) ++ return -ENOMEM; ++ ++ ret = device_property_read_u32(&pdev->dev, "voicehat_sdmode_delay", ++ &sdmode_delay); ++ ++ if (ret) { ++ sdmode_delay = SDMODE_DELAY_MS; ++ dev_info(&pdev->dev, ++ "property 'voicehat_sdmode_delay' not found default 5 mS"); ++ } else { ++ dev_info(&pdev->dev, "property 'voicehat_sdmode_delay' found delay= %d mS", ++ sdmode_delay); ++ } ++ voicehat->sdmode_delay_jiffies = msecs_to_jiffies(sdmode_delay); ++ ++ dev_set_drvdata(&pdev->dev, voicehat); ++ ++ return snd_soc_register_component(&pdev->dev, ++ &voicehat_component_driver, ++ &voicehat_dai, ++ 1); ++} ++ ++static int voicehat_platform_remove(struct platform_device *pdev) ++{ ++ snd_soc_unregister_component(&pdev->dev); ++ return 0; ++} ++ ++static struct platform_driver voicehat_driver = { ++ .driver = { ++ .name = "voicehat-codec", ++ .of_match_table = of_match_ptr(voicehat_ids), ++ }, ++ .probe = voicehat_platform_probe, ++ .remove = voicehat_platform_remove, ++}; ++ ++module_platform_driver(voicehat_driver); ++ ++MODULE_DESCRIPTION("Google voiceHAT Codec driver"); ++MODULE_AUTHOR("Peter Malkin "); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/hifiberry_dacplus.c +@@ -0,0 +1,424 @@ ++/* ++ * ASoC Driver for HiFiBerry DAC+ / DAC Pro ++ * ++ * Author: Daniel Matuschek, Stuart MacLean ++ * Copyright 2014-2015 ++ * based on code by Florian Meier ++ * Headphone added by Joerg Schambacher, joerg@i2audio.com ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++ ++#include "../codecs/pcm512x.h" ++ ++#define HIFIBERRY_DACPRO_NOCLOCK 0 ++#define HIFIBERRY_DACPRO_CLK44EN 1 ++#define HIFIBERRY_DACPRO_CLK48EN 2 ++ ++struct pcm512x_priv { ++ struct regmap *regmap; ++ struct clk *sclk; ++}; ++ ++/* Clock rate of CLK44EN attached to GPIO6 pin */ ++#define CLK_44EN_RATE 22579200UL ++/* Clock rate of CLK48EN attached to GPIO3 pin */ ++#define CLK_48EN_RATE 24576000UL ++ ++static bool slave; ++static bool snd_rpi_hifiberry_is_dacpro; ++static bool digital_gain_0db_limit = true; ++static bool leds_off; ++ ++static void snd_rpi_hifiberry_dacplus_select_clk(struct snd_soc_component *component, ++ int clk_id) ++{ ++ switch (clk_id) { ++ case HIFIBERRY_DACPRO_NOCLOCK: ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x24, 0x00); ++ break; ++ case HIFIBERRY_DACPRO_CLK44EN: ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x24, 0x20); ++ break; ++ case HIFIBERRY_DACPRO_CLK48EN: ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x24, 0x04); ++ break; ++ } ++} ++ ++static void snd_rpi_hifiberry_dacplus_clk_gpio(struct snd_soc_component *component) ++{ ++ snd_soc_component_update_bits(component, PCM512x_GPIO_EN, 0x24, 0x24); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_OUTPUT_3, 0x0f, 0x02); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_OUTPUT_6, 0x0f, 0x02); ++} ++ ++static bool snd_rpi_hifiberry_dacplus_is_sclk(struct snd_soc_component *component) ++{ ++ unsigned int sck; ++ ++ sck = snd_soc_component_read(component, PCM512x_RATE_DET_4); ++ return (!(sck & 0x40)); ++} ++ ++static bool snd_rpi_hifiberry_dacplus_is_sclk_sleep( ++ struct snd_soc_component *component) ++{ ++ msleep(2); ++ return snd_rpi_hifiberry_dacplus_is_sclk(component); ++} ++ ++static bool snd_rpi_hifiberry_dacplus_is_pro_card(struct snd_soc_component *component) ++{ ++ bool isClk44EN, isClk48En, isNoClk; ++ ++ snd_rpi_hifiberry_dacplus_clk_gpio(component); ++ ++ snd_rpi_hifiberry_dacplus_select_clk(component, HIFIBERRY_DACPRO_CLK44EN); ++ isClk44EN = snd_rpi_hifiberry_dacplus_is_sclk_sleep(component); ++ ++ snd_rpi_hifiberry_dacplus_select_clk(component, HIFIBERRY_DACPRO_NOCLOCK); ++ isNoClk = snd_rpi_hifiberry_dacplus_is_sclk_sleep(component); ++ ++ snd_rpi_hifiberry_dacplus_select_clk(component, HIFIBERRY_DACPRO_CLK48EN); ++ isClk48En = snd_rpi_hifiberry_dacplus_is_sclk_sleep(component); ++ ++ return (isClk44EN && isClk48En && !isNoClk); ++} ++ ++static int snd_rpi_hifiberry_dacplus_clk_for_rate(int sample_rate) ++{ ++ int type; ++ ++ switch (sample_rate) { ++ case 11025: ++ case 22050: ++ case 44100: ++ case 88200: ++ case 176400: ++ case 352800: ++ type = HIFIBERRY_DACPRO_CLK44EN; ++ break; ++ default: ++ type = HIFIBERRY_DACPRO_CLK48EN; ++ break; ++ } ++ return type; ++} ++ ++static void snd_rpi_hifiberry_dacplus_set_sclk(struct snd_soc_component *component, ++ int sample_rate) ++{ ++ struct pcm512x_priv *pcm512x = snd_soc_component_get_drvdata(component); ++ ++ if (!IS_ERR(pcm512x->sclk)) { ++ int ctype; ++ ++ ctype = snd_rpi_hifiberry_dacplus_clk_for_rate(sample_rate); ++ clk_set_rate(pcm512x->sclk, (ctype == HIFIBERRY_DACPRO_CLK44EN) ++ ? CLK_44EN_RATE : CLK_48EN_RATE); ++ snd_rpi_hifiberry_dacplus_select_clk(component, ctype); ++ } ++} ++ ++static int snd_rpi_hifiberry_dacplus_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ struct pcm512x_priv *priv; ++ ++ if (slave) ++ snd_rpi_hifiberry_is_dacpro = false; ++ else ++ snd_rpi_hifiberry_is_dacpro = ++ snd_rpi_hifiberry_dacplus_is_pro_card(component); ++ ++ if (snd_rpi_hifiberry_is_dacpro) { ++ struct snd_soc_dai_link *dai = rtd->dai_link; ++ ++ dai->name = "HiFiBerry DAC+ Pro"; ++ dai->stream_name = "HiFiBerry DAC+ Pro HiFi"; ++ dai->dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF ++ | SND_SOC_DAIFMT_CBM_CFM; ++ ++ snd_soc_component_update_bits(component, PCM512x_BCLK_LRCLK_CFG, 0x31, 0x11); ++ snd_soc_component_update_bits(component, PCM512x_MASTER_MODE, 0x03, 0x03); ++ snd_soc_component_update_bits(component, PCM512x_MASTER_CLKDIV_2, 0x7f, 63); ++ } else { ++ priv = snd_soc_component_get_drvdata(component); ++ priv->sclk = ERR_PTR(-ENOENT); ++ } ++ ++ snd_soc_component_update_bits(component, PCM512x_GPIO_EN, 0x08, 0x08); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_OUTPUT_4, 0x0f, 0x02); ++ if (leds_off) ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x08, 0x00); ++ else ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x08, 0x08); ++ ++ if (digital_gain_0db_limit) { ++ int ret; ++ struct snd_soc_card *card = rtd->card; ++ ++ ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207); ++ if (ret < 0) ++ dev_warn(card->dev, "Failed to set volume limit: %d\n", ret); ++ } ++ ++ return 0; ++} ++ ++static int snd_rpi_hifiberry_dacplus_update_rate_den( ++ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ struct pcm512x_priv *pcm512x = snd_soc_component_get_drvdata(component); ++ struct snd_ratnum *rats_no_pll; ++ unsigned int num = 0, den = 0; ++ int err; ++ ++ rats_no_pll = devm_kzalloc(rtd->dev, sizeof(*rats_no_pll), GFP_KERNEL); ++ if (!rats_no_pll) ++ return -ENOMEM; ++ ++ rats_no_pll->num = clk_get_rate(pcm512x->sclk) / 64; ++ rats_no_pll->den_min = 1; ++ rats_no_pll->den_max = 128; ++ rats_no_pll->den_step = 1; ++ ++ err = snd_interval_ratnum(hw_param_interval(params, ++ SNDRV_PCM_HW_PARAM_RATE), 1, rats_no_pll, &num, &den); ++ if (err >= 0 && den) { ++ params->rate_num = num; ++ params->rate_den = den; ++ } ++ ++ devm_kfree(rtd->dev, rats_no_pll); ++ return 0; ++} ++ ++static int snd_rpi_hifiberry_dacplus_hw_params( ++ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params) ++{ ++ int ret = 0; ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ int channels = params_channels(params); ++ int width = 32; ++ ++ if (snd_rpi_hifiberry_is_dacpro) { ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ ++ width = snd_pcm_format_physical_width(params_format(params)); ++ ++ snd_rpi_hifiberry_dacplus_set_sclk(component, ++ params_rate(params)); ++ ++ ret = snd_rpi_hifiberry_dacplus_update_rate_den( ++ substream, params); ++ } ++ ++ ret = snd_soc_dai_set_bclk_ratio(asoc_rtd_to_cpu(rtd, 0), channels * width); ++ if (ret) ++ return ret; ++ ret = snd_soc_dai_set_bclk_ratio(asoc_rtd_to_codec(rtd, 0), channels * width); ++ return ret; ++} ++ ++static int snd_rpi_hifiberry_dacplus_startup( ++ struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ ++ if (leds_off) ++ return 0; ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x08, 0x08); ++ return 0; ++} ++ ++static void snd_rpi_hifiberry_dacplus_shutdown( ++ struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x08, 0x00); ++} ++ ++/* machine stream operations */ ++static struct snd_soc_ops snd_rpi_hifiberry_dacplus_ops = { ++ .hw_params = snd_rpi_hifiberry_dacplus_hw_params, ++ .startup = snd_rpi_hifiberry_dacplus_startup, ++ .shutdown = snd_rpi_hifiberry_dacplus_shutdown, ++}; ++ ++SND_SOC_DAILINK_DEFS(rpi_hifiberry_dacplus, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("pcm512x.1-004d", "pcm512x-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_rpi_hifiberry_dacplus_dai[] = { ++{ ++ .name = "HiFiBerry DAC+", ++ .stream_name = "HiFiBerry DAC+ HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ .ops = &snd_rpi_hifiberry_dacplus_ops, ++ .init = snd_rpi_hifiberry_dacplus_init, ++ SND_SOC_DAILINK_REG(rpi_hifiberry_dacplus), ++}, ++}; ++ ++/* aux device for optional headphone amp */ ++static struct snd_soc_aux_dev hifiberry_dacplus_aux_devs[] = { ++ { ++ .dlc = { ++ .name = "tpa6130a2.1-0060", ++ }, ++ }, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_rpi_hifiberry_dacplus = { ++ .name = "snd_rpi_hifiberry_dacplus", ++ .driver_name = "HifiberryDacp", ++ .owner = THIS_MODULE, ++ .dai_link = snd_rpi_hifiberry_dacplus_dai, ++ .num_links = ARRAY_SIZE(snd_rpi_hifiberry_dacplus_dai), ++}; ++ ++static int hb_hp_detect(void) ++{ ++ struct i2c_adapter *adap = i2c_get_adapter(1); ++ int ret; ++ ++ struct i2c_client tpa_i2c_client = { ++ .addr = 0x60, ++ .adapter = adap, ++ }; ++ ++ ret = i2c_smbus_read_byte(&tpa_i2c_client) >= 0; ++ i2c_put_adapter(adap); ++ return ret; ++}; ++ ++static struct property tpa_enable_prop = { ++ .name = "status", ++ .length = 4 + 1, /* length 'okay' + 1 */ ++ .value = "okay", ++ }; ++ ++static int snd_rpi_hifiberry_dacplus_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ struct snd_soc_card *card = &snd_rpi_hifiberry_dacplus; ++ int len; ++ struct device_node *tpa_node; ++ struct property *tpa_prop; ++ struct of_changeset ocs; ++ ++ /* probe for head phone amp */ ++ if (hb_hp_detect()) { ++ card->aux_dev = hifiberry_dacplus_aux_devs; ++ card->num_aux_devs = ++ ARRAY_SIZE(hifiberry_dacplus_aux_devs); ++ tpa_node = of_find_compatible_node(NULL, NULL, "ti,tpa6130a2"); ++ tpa_prop = of_find_property(tpa_node, "status", &len); ++ ++ if (strcmp((char *)tpa_prop->value, "okay")) { ++ /* and activate headphone using change_sets */ ++ dev_info(&pdev->dev, "activating headphone amplifier"); ++ of_changeset_init(&ocs); ++ ret = of_changeset_update_property(&ocs, tpa_node, ++ &tpa_enable_prop); ++ if (ret) { ++ dev_err(&pdev->dev, ++ "cannot activate headphone amplifier\n"); ++ return -ENODEV; ++ } ++ ret = of_changeset_apply(&ocs); ++ if (ret) { ++ dev_err(&pdev->dev, ++ "cannot activate headphone amplifier\n"); ++ return -ENODEV; ++ } ++ } ++ } ++ ++ snd_rpi_hifiberry_dacplus.dev = &pdev->dev; ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai; ++ ++ dai = &snd_rpi_hifiberry_dacplus_dai[0]; ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ ++ if (i2s_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } ++ ++ digital_gain_0db_limit = !of_property_read_bool( ++ pdev->dev.of_node, "hifiberry,24db_digital_gain"); ++ slave = of_property_read_bool(pdev->dev.of_node, ++ "hifiberry-dacplus,slave"); ++ leds_off = of_property_read_bool(pdev->dev.of_node, ++ "hifiberry-dacplus,leds_off"); ++ } ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, ++ &snd_rpi_hifiberry_dacplus); ++ if (ret && ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ ++ return ret; ++} ++ ++static const struct of_device_id snd_rpi_hifiberry_dacplus_of_match[] = { ++ { .compatible = "hifiberry,hifiberry-dacplus", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, snd_rpi_hifiberry_dacplus_of_match); ++ ++static struct platform_driver snd_rpi_hifiberry_dacplus_driver = { ++ .driver = { ++ .name = "snd-rpi-hifiberry-dacplus", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_rpi_hifiberry_dacplus_of_match, ++ }, ++ .probe = snd_rpi_hifiberry_dacplus_probe, ++}; ++ ++module_platform_driver(snd_rpi_hifiberry_dacplus_driver); ++ ++MODULE_AUTHOR("Daniel Matuschek "); ++MODULE_DESCRIPTION("ASoC Driver for HiFiBerry DAC+"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/hifiberry_dacplusadc.c +@@ -0,0 +1,398 @@ ++/* ++ * ASoC Driver for HiFiBerry DAC+ / DAC Pro with ADC ++ * ++ * Author: Daniel Matuschek, Stuart MacLean ++ * Copyright 2014-2015 ++ * based on code by Florian Meier ++ * ADC added by Joerg Schambacher ++ * Copyright 2018 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++ ++#include "../codecs/pcm512x.h" ++ ++#define HIFIBERRY_DACPRO_NOCLOCK 0 ++#define HIFIBERRY_DACPRO_CLK44EN 1 ++#define HIFIBERRY_DACPRO_CLK48EN 2 ++ ++struct platform_device *dmic_codec_dev; ++ ++struct pcm512x_priv { ++ struct regmap *regmap; ++ struct clk *sclk; ++}; ++ ++/* Clock rate of CLK44EN attached to GPIO6 pin */ ++#define CLK_44EN_RATE 22579200UL ++/* Clock rate of CLK48EN attached to GPIO3 pin */ ++#define CLK_48EN_RATE 24576000UL ++ ++static bool slave; ++static bool snd_rpi_hifiberry_is_dacpro; ++static bool digital_gain_0db_limit = true; ++static bool leds_off; ++ ++static void snd_rpi_hifiberry_dacplusadc_select_clk(struct snd_soc_component *component, ++ int clk_id) ++{ ++ switch (clk_id) { ++ case HIFIBERRY_DACPRO_NOCLOCK: ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x24, 0x00); ++ break; ++ case HIFIBERRY_DACPRO_CLK44EN: ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x24, 0x20); ++ break; ++ case HIFIBERRY_DACPRO_CLK48EN: ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x24, 0x04); ++ break; ++ } ++} ++ ++static void snd_rpi_hifiberry_dacplusadc_clk_gpio(struct snd_soc_component *component) ++{ ++ snd_soc_component_update_bits(component, PCM512x_GPIO_EN, 0x24, 0x24); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_OUTPUT_3, 0x0f, 0x02); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_OUTPUT_6, 0x0f, 0x02); ++} ++ ++static bool snd_rpi_hifiberry_dacplusadc_is_sclk(struct snd_soc_component *component) ++{ ++ unsigned int sck; ++ ++ sck = snd_soc_component_read(component, PCM512x_RATE_DET_4); ++ return (!(sck & 0x40)); ++} ++ ++static bool snd_rpi_hifiberry_dacplusadc_is_sclk_sleep( ++ struct snd_soc_component *component) ++{ ++ msleep(2); ++ return snd_rpi_hifiberry_dacplusadc_is_sclk(component); ++} ++ ++static bool snd_rpi_hifiberry_dacplusadc_is_pro_card(struct snd_soc_component *component) ++{ ++ bool isClk44EN, isClk48En, isNoClk; ++ ++ snd_rpi_hifiberry_dacplusadc_clk_gpio(component); ++ ++ snd_rpi_hifiberry_dacplusadc_select_clk(component, HIFIBERRY_DACPRO_CLK44EN); ++ isClk44EN = snd_rpi_hifiberry_dacplusadc_is_sclk_sleep(component); ++ ++ snd_rpi_hifiberry_dacplusadc_select_clk(component, HIFIBERRY_DACPRO_NOCLOCK); ++ isNoClk = snd_rpi_hifiberry_dacplusadc_is_sclk_sleep(component); ++ ++ snd_rpi_hifiberry_dacplusadc_select_clk(component, HIFIBERRY_DACPRO_CLK48EN); ++ isClk48En = snd_rpi_hifiberry_dacplusadc_is_sclk_sleep(component); ++ ++ return (isClk44EN && isClk48En && !isNoClk); ++} ++ ++static int snd_rpi_hifiberry_dacplusadc_clk_for_rate(int sample_rate) ++{ ++ int type; ++ ++ switch (sample_rate) { ++ case 11025: ++ case 22050: ++ case 44100: ++ case 88200: ++ case 176400: ++ case 352800: ++ type = HIFIBERRY_DACPRO_CLK44EN; ++ break; ++ default: ++ type = HIFIBERRY_DACPRO_CLK48EN; ++ break; ++ } ++ return type; ++} ++ ++static void snd_rpi_hifiberry_dacplusadc_set_sclk(struct snd_soc_component *component, ++ int sample_rate) ++{ ++ struct pcm512x_priv *pcm512x = snd_soc_component_get_drvdata(component); ++ ++ if (!IS_ERR(pcm512x->sclk)) { ++ int ctype; ++ ++ ctype = snd_rpi_hifiberry_dacplusadc_clk_for_rate(sample_rate); ++ clk_set_rate(pcm512x->sclk, (ctype == HIFIBERRY_DACPRO_CLK44EN) ++ ? CLK_44EN_RATE : CLK_48EN_RATE); ++ snd_rpi_hifiberry_dacplusadc_select_clk(component, ctype); ++ } ++} ++ ++static int snd_rpi_hifiberry_dacplusadc_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ struct pcm512x_priv *priv; ++ ++ if (slave) ++ snd_rpi_hifiberry_is_dacpro = false; ++ else ++ snd_rpi_hifiberry_is_dacpro = ++ snd_rpi_hifiberry_dacplusadc_is_pro_card(component); ++ ++ if (snd_rpi_hifiberry_is_dacpro) { ++ struct snd_soc_dai_link *dai = rtd->dai_link; ++ ++ dai->name = "HiFiBerry ADCDAC+ Pro"; ++ dai->stream_name = "HiFiBerry ADCDAC+ Pro HiFi"; ++ dai->dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF ++ | SND_SOC_DAIFMT_CBM_CFM; ++ ++ snd_soc_component_update_bits(component, PCM512x_BCLK_LRCLK_CFG, 0x31, 0x11); ++ snd_soc_component_update_bits(component, PCM512x_MASTER_MODE, 0x03, 0x03); ++ snd_soc_component_update_bits(component, PCM512x_MASTER_CLKDIV_2, 0x7f, 63); ++ } else { ++ priv = snd_soc_component_get_drvdata(component); ++ priv->sclk = ERR_PTR(-ENOENT); ++ } ++ ++ snd_soc_component_update_bits(component, PCM512x_GPIO_EN, 0x08, 0x08); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_OUTPUT_4, 0x0f, 0x02); ++ if (leds_off) ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x08, 0x00); ++ else ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x08, 0x08); ++ ++ if (digital_gain_0db_limit) { ++ int ret; ++ struct snd_soc_card *card = rtd->card; ++ ++ ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207); ++ if (ret < 0) ++ dev_warn(card->dev, "Failed to set volume limit: %d\n", ret); ++ } ++ ++ return 0; ++} ++ ++static int snd_rpi_hifiberry_dacplusadc_update_rate_den( ++ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ struct pcm512x_priv *pcm512x = snd_soc_component_get_drvdata(component); ++ struct snd_ratnum *rats_no_pll; ++ unsigned int num = 0, den = 0; ++ int err; ++ ++ rats_no_pll = devm_kzalloc(rtd->dev, sizeof(*rats_no_pll), GFP_KERNEL); ++ if (!rats_no_pll) ++ return -ENOMEM; ++ ++ rats_no_pll->num = clk_get_rate(pcm512x->sclk) / 64; ++ rats_no_pll->den_min = 1; ++ rats_no_pll->den_max = 128; ++ rats_no_pll->den_step = 1; ++ ++ err = snd_interval_ratnum(hw_param_interval(params, ++ SNDRV_PCM_HW_PARAM_RATE), 1, rats_no_pll, &num, &den); ++ if (err >= 0 && den) { ++ params->rate_num = num; ++ params->rate_den = den; ++ } ++ ++ devm_kfree(rtd->dev, rats_no_pll); ++ return 0; ++} ++ ++static int snd_rpi_hifiberry_dacplusadc_hw_params( ++ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params) ++{ ++ int ret = 0; ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ int channels = params_channels(params); ++ int width = 32; ++ ++ if (snd_rpi_hifiberry_is_dacpro) { ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ ++ width = snd_pcm_format_physical_width(params_format(params)); ++ ++ snd_rpi_hifiberry_dacplusadc_set_sclk(component, ++ params_rate(params)); ++ ++ ret = snd_rpi_hifiberry_dacplusadc_update_rate_den( ++ substream, params); ++ } ++ ++ ret = snd_soc_dai_set_bclk_ratio(asoc_rtd_to_cpu(rtd, 0), channels * width); ++ if (ret) ++ return ret; ++ ret = snd_soc_dai_set_bclk_ratio(asoc_rtd_to_codec(rtd, 0), channels * width); ++ return ret; ++} ++ ++static int hifiberry_dacplusadc_LED_cnt; ++ ++static int snd_rpi_hifiberry_dacplusadc_startup( ++ struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ ++ if (leds_off) ++ return 0; ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, ++ 0x08, 0x08); ++ hifiberry_dacplusadc_LED_cnt++; ++ return 0; ++} ++ ++static void snd_rpi_hifiberry_dacplusadc_shutdown( ++ struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ ++ hifiberry_dacplusadc_LED_cnt--; ++ if (!hifiberry_dacplusadc_LED_cnt) ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, ++ 0x08, 0x00); ++} ++ ++/* machine stream operations */ ++static struct snd_soc_ops snd_rpi_hifiberry_dacplusadc_ops = { ++ .hw_params = snd_rpi_hifiberry_dacplusadc_hw_params, ++ .startup = snd_rpi_hifiberry_dacplusadc_startup, ++ .shutdown = snd_rpi_hifiberry_dacplusadc_shutdown, ++}; ++ ++SND_SOC_DAILINK_DEFS(hifi, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("pcm512x.1-004d", "pcm512x-hifi"), ++ COMP_CODEC("dmic-codec", "dmic-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_rpi_hifiberry_dacplusadc_dai[] = { ++{ ++ .name = "HiFiBerry DAC+ADC", ++ .stream_name = "HiFiBerry DAC+ADC HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ .ops = &snd_rpi_hifiberry_dacplusadc_ops, ++ .init = snd_rpi_hifiberry_dacplusadc_init, ++ SND_SOC_DAILINK_REG(hifi), ++}, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_rpi_hifiberry_dacplusadc = { ++ .name = "snd_rpi_hifiberry_dacplusadc", ++ .driver_name = "HifiberryDacpAdc", ++ .owner = THIS_MODULE, ++ .dai_link = snd_rpi_hifiberry_dacplusadc_dai, ++ .num_links = ARRAY_SIZE(snd_rpi_hifiberry_dacplusadc_dai), ++}; ++ ++ ++static int snd_rpi_hifiberry_dacplusadc_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ ++ snd_rpi_hifiberry_dacplusadc.dev = &pdev->dev; ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai; ++ ++ dai = &snd_rpi_hifiberry_dacplusadc_dai[0]; ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ if (i2s_node) { ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->of_node = i2s_node; ++ dai->cpus->dai_name = NULL; ++ dai->platforms->name = NULL; ++ } ++ } ++ digital_gain_0db_limit = !of_property_read_bool( ++ pdev->dev.of_node, "hifiberry,24db_digital_gain"); ++ slave = of_property_read_bool(pdev->dev.of_node, ++ "hifiberry-dacplusadc,slave"); ++ leds_off = of_property_read_bool(pdev->dev.of_node, ++ "hifiberry-dacplusadc,leds_off"); ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, ++ &snd_rpi_hifiberry_dacplusadc); ++ if (ret && ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ ++ return ret; ++} ++ ++static const struct of_device_id snd_rpi_hifiberry_dacplusadc_of_match[] = { ++ { .compatible = "hifiberry,hifiberry-dacplusadc", }, ++ {}, ++}; ++ ++MODULE_DEVICE_TABLE(of, snd_rpi_hifiberry_dacplusadc_of_match); ++ ++static struct platform_driver snd_rpi_hifiberry_dacplusadc_driver = { ++ .driver = { ++ .name = "snd-rpi-hifiberry-dacplusadc", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_rpi_hifiberry_dacplusadc_of_match, ++ }, ++ .probe = snd_rpi_hifiberry_dacplusadc_probe, ++}; ++ ++static int __init hifiberry_dacplusadc_init(void) ++{ ++ int ret; ++ ++ dmic_codec_dev = platform_device_register_simple("dmic-codec", -1, NULL, ++ 0); ++ if (IS_ERR(dmic_codec_dev)) { ++ pr_err("%s: dmic-codec device registration failed\n", __func__); ++ return PTR_ERR(dmic_codec_dev); ++ } ++ ++ ret = platform_driver_register(&snd_rpi_hifiberry_dacplusadc_driver); ++ if (ret) { ++ pr_err("%s: platform driver registration failed\n", __func__); ++ platform_device_unregister(dmic_codec_dev); ++ } ++ ++ return ret; ++} ++module_init(hifiberry_dacplusadc_init); ++ ++static void __exit hifiberry_dacplusadc_exit(void) ++{ ++ platform_driver_unregister(&snd_rpi_hifiberry_dacplusadc_driver); ++ platform_device_unregister(dmic_codec_dev); ++} ++module_exit(hifiberry_dacplusadc_exit); ++ ++MODULE_AUTHOR("Joerg Schambacher "); ++MODULE_AUTHOR("Daniel Matuschek "); ++MODULE_DESCRIPTION("ASoC Driver for HiFiBerry DAC+ADC"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/hifiberry_dacplusadcpro.c +@@ -0,0 +1,543 @@ ++/* ++ * ASoC Driver for HiFiBerry DAC+ / DAC Pro with ADC PRO Version (SW control) ++ * ++ * Author: Daniel Matuschek, Stuart MacLean ++ * Copyright 2014-2015 ++ * based on code by Florian Meier ++ * ADC added by Joerg Schambacher ++ * Copyright 2018-19 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "../codecs/pcm512x.h" ++#include "../codecs/pcm186x.h" ++ ++#define HIFIBERRY_DACPRO_NOCLOCK 0 ++#define HIFIBERRY_DACPRO_CLK44EN 1 ++#define HIFIBERRY_DACPRO_CLK48EN 2 ++ ++struct pcm512x_priv { ++ struct regmap *regmap; ++ struct clk *sclk; ++}; ++ ++/* Clock rate of CLK44EN attached to GPIO6 pin */ ++#define CLK_44EN_RATE 22579200UL ++/* Clock rate of CLK48EN attached to GPIO3 pin */ ++#define CLK_48EN_RATE 24576000UL ++ ++static bool slave; ++static bool snd_rpi_hifiberry_is_dacpro; ++static bool digital_gain_0db_limit = true; ++static bool leds_off; ++ ++static const unsigned int pcm186x_adc_input_channel_sel_value[] = { ++ 0x00, 0x01, 0x02, 0x03, 0x10 ++}; ++ ++static const char * const pcm186x_adcl_input_channel_sel_text[] = { ++ "No Select", ++ "VINL1[SE]", /* Default for ADCL */ ++ "VINL2[SE]", ++ "VINL2[SE] + VINL1[SE]", ++ "{VIN1P, VIN1M}[DIFF]" ++}; ++ ++static const char * const pcm186x_adcr_input_channel_sel_text[] = { ++ "No Select", ++ "VINR1[SE]", /* Default for ADCR */ ++ "VINR2[SE]", ++ "VINR2[SE] + VINR1[SE]", ++ "{VIN2P, VIN2M}[DIFF]" ++}; ++ ++static const struct soc_enum pcm186x_adc_input_channel_sel[] = { ++ SOC_VALUE_ENUM_SINGLE(PCM186X_ADC1_INPUT_SEL_L, 0, ++ PCM186X_ADC_INPUT_SEL_MASK, ++ ARRAY_SIZE(pcm186x_adcl_input_channel_sel_text), ++ pcm186x_adcl_input_channel_sel_text, ++ pcm186x_adc_input_channel_sel_value), ++ SOC_VALUE_ENUM_SINGLE(PCM186X_ADC1_INPUT_SEL_R, 0, ++ PCM186X_ADC_INPUT_SEL_MASK, ++ ARRAY_SIZE(pcm186x_adcr_input_channel_sel_text), ++ pcm186x_adcr_input_channel_sel_text, ++ pcm186x_adc_input_channel_sel_value), ++}; ++ ++static const unsigned int pcm186x_mic_bias_sel_value[] = { ++ 0x00, 0x01, 0x11 ++}; ++ ++static const char * const pcm186x_mic_bias_sel_text[] = { ++ "Mic Bias off", ++ "Mic Bias on", ++ "Mic Bias with Bypass Resistor" ++}; ++ ++static const struct soc_enum pcm186x_mic_bias_sel[] = { ++ SOC_VALUE_ENUM_SINGLE(PCM186X_MIC_BIAS_CTRL, 0, ++ GENMASK(4, 0), ++ ARRAY_SIZE(pcm186x_mic_bias_sel_text), ++ pcm186x_mic_bias_sel_text, ++ pcm186x_mic_bias_sel_value), ++}; ++ ++static const unsigned int pcm186x_gain_sel_value[] = { ++ 0xe8, 0xe9, 0xea, 0xeb, 0xec, 0xed, 0xee, 0xef, ++ 0xf0, 0xf1, 0xf2, 0xf3, 0xf4, 0xf5, 0xf6, 0xf7, ++ 0xf8, 0xf9, 0xfa, 0xfb, 0xfc, 0xfd, 0xfe, 0xff, ++ 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07, ++ 0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f, ++ 0x10, 0x11, 0x12, 0x13, 0x14, 0x15, 0x16, 0x17, ++ 0x18, 0x19, 0x1a, 0x1b, 0x1c, 0x1d, 0x1e, 0x1f, ++ 0x20, 0x21, 0x22, 0x23, 0x24, 0x25, 0x26, 0x27, ++ 0x28, 0x29, 0x2a, 0x2b, 0x2c, 0x2d, 0x2e, 0x2f, ++ 0x30, 0x31, 0x32, 0x33, 0x34, 0x35, 0x36, 0x37, ++ 0x38, 0x39, 0x3a, 0x3b, 0x3c, 0x3d, 0x3e, 0x3f, ++ 0x40, 0x41, 0x42, 0x43, 0x44, 0x45, 0x46, 0x47, ++ 0x48, 0x49, 0x4a, 0x4b, 0x4c, 0x4d, 0x4e, 0x4f, ++ 0x50 ++}; ++ ++static const char * const pcm186x_gain_sel_text[] = { ++ "-12.0dB", "-11.5dB", "-11.0dB", "-10.5dB", "-10.0dB", "-9.5dB", ++ "-9.0dB", "-8.5dB", "-8.0dB", "-7.5dB", "-7.0dB", "-6.5dB", ++ "-6.0dB", "-5.5dB", "-5.0dB", "-4.5dB", "-4.0dB", "-3.5dB", ++ "-3.0dB", "-2.5dB", "-2.0dB", "-1.5dB", "-1.0dB", "-0.5dB", ++ "0.0dB", "0.5dB", "1.0dB", "1.5dB", "2.0dB", "2.5dB", ++ "3.0dB", "3.5dB", "4.0dB", "4.5dB", "5.0dB", "5.5dB", ++ "6.0dB", "6.5dB", "7.0dB", "7.5dB", "8.0dB", "8.5dB", ++ "9.0dB", "9.5dB", "10.0dB", "10.5dB", "11.0dB", "11.5dB", ++ "12.0dB", "12.5dB", "13.0dB", "13.5dB", "14.0dB", "14.5dB", ++ "15.0dB", "15.5dB", "16.0dB", "16.5dB", "17.0dB", "17.5dB", ++ "18.0dB", "18.5dB", "19.0dB", "19.5dB", "20.0dB", "20.5dB", ++ "21.0dB", "21.5dB", "22.0dB", "22.5dB", "23.0dB", "23.5dB", ++ "24.0dB", "24.5dB", "25.0dB", "25.5dB", "26.0dB", "26.5dB", ++ "27.0dB", "27.5dB", "28.0dB", "28.5dB", "29.0dB", "29.5dB", ++ "30.0dB", "30.5dB", "31.0dB", "31.5dB", "32.0dB", "32.5dB", ++ "33.0dB", "33.5dB", "34.0dB", "34.5dB", "35.0dB", "35.5dB", ++ "36.0dB", "36.5dB", "37.0dB", "37.5dB", "38.0dB", "38.5dB", ++ "39.0dB", "39.5dB", "40.0dB"}; ++ ++static const struct soc_enum pcm186x_gain_sel[] = { ++ SOC_VALUE_ENUM_SINGLE(PCM186X_PGA_VAL_CH1_L, 0, ++ 0xff, ++ ARRAY_SIZE(pcm186x_gain_sel_text), ++ pcm186x_gain_sel_text, ++ pcm186x_gain_sel_value), ++ SOC_VALUE_ENUM_SINGLE(PCM186X_PGA_VAL_CH1_R, 0, ++ 0xff, ++ ARRAY_SIZE(pcm186x_gain_sel_text), ++ pcm186x_gain_sel_text, ++ pcm186x_gain_sel_value), ++}; ++ ++static const struct snd_kcontrol_new pcm1863_snd_controls_card[] = { ++ SOC_ENUM("ADC Left Input", pcm186x_adc_input_channel_sel[0]), ++ SOC_ENUM("ADC Right Input", pcm186x_adc_input_channel_sel[1]), ++ SOC_ENUM("ADC Mic Bias", pcm186x_mic_bias_sel), ++ SOC_ENUM("PGA Gain Left", pcm186x_gain_sel[0]), ++ SOC_ENUM("PGA Gain Right", pcm186x_gain_sel[1]), ++}; ++ ++static int pcm1863_add_controls(struct snd_soc_component *component) ++{ ++ snd_soc_add_component_controls(component, ++ pcm1863_snd_controls_card, ++ ARRAY_SIZE(pcm1863_snd_controls_card)); ++ return 0; ++} ++ ++static void snd_rpi_hifiberry_dacplusadcpro_select_clk( ++ struct snd_soc_component *component, int clk_id) ++{ ++ switch (clk_id) { ++ case HIFIBERRY_DACPRO_NOCLOCK: ++ snd_soc_component_update_bits(component, ++ PCM512x_GPIO_CONTROL_1, 0x24, 0x00); ++ break; ++ case HIFIBERRY_DACPRO_CLK44EN: ++ snd_soc_component_update_bits(component, ++ PCM512x_GPIO_CONTROL_1, 0x24, 0x20); ++ break; ++ case HIFIBERRY_DACPRO_CLK48EN: ++ snd_soc_component_update_bits(component, ++ PCM512x_GPIO_CONTROL_1, 0x24, 0x04); ++ break; ++ } ++} ++ ++static void snd_rpi_hifiberry_dacplusadcpro_clk_gpio(struct snd_soc_component *component) ++{ ++ snd_soc_component_update_bits(component, PCM512x_GPIO_EN, 0x24, 0x24); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_OUTPUT_3, 0x0f, 0x02); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_OUTPUT_6, 0x0f, 0x02); ++} ++ ++static bool snd_rpi_hifiberry_dacplusadcpro_is_sclk(struct snd_soc_component *component) ++{ ++ unsigned int sck; ++ ++ sck = snd_soc_component_read(component, PCM512x_RATE_DET_4); ++ return (!(sck & 0x40)); ++} ++ ++static bool snd_rpi_hifiberry_dacplusadcpro_is_sclk_sleep( ++ struct snd_soc_component *component) ++{ ++ msleep(2); ++ return snd_rpi_hifiberry_dacplusadcpro_is_sclk(component); ++} ++ ++static bool snd_rpi_hifiberry_dacplusadcpro_is_pro_card(struct snd_soc_component *component) ++{ ++ bool isClk44EN, isClk48En, isNoClk; ++ ++ snd_rpi_hifiberry_dacplusadcpro_clk_gpio(component); ++ ++ snd_rpi_hifiberry_dacplusadcpro_select_clk(component, HIFIBERRY_DACPRO_CLK44EN); ++ isClk44EN = snd_rpi_hifiberry_dacplusadcpro_is_sclk_sleep(component); ++ ++ snd_rpi_hifiberry_dacplusadcpro_select_clk(component, HIFIBERRY_DACPRO_NOCLOCK); ++ isNoClk = snd_rpi_hifiberry_dacplusadcpro_is_sclk_sleep(component); ++ ++ snd_rpi_hifiberry_dacplusadcpro_select_clk(component, HIFIBERRY_DACPRO_CLK48EN); ++ isClk48En = snd_rpi_hifiberry_dacplusadcpro_is_sclk_sleep(component); ++ ++ return (isClk44EN && isClk48En && !isNoClk); ++} ++ ++static int snd_rpi_hifiberry_dacplusadcpro_clk_for_rate(int sample_rate) ++{ ++ int type; ++ ++ switch (sample_rate) { ++ case 11025: ++ case 22050: ++ case 44100: ++ case 88200: ++ case 176400: ++ case 352800: ++ type = HIFIBERRY_DACPRO_CLK44EN; ++ break; ++ default: ++ type = HIFIBERRY_DACPRO_CLK48EN; ++ break; ++ } ++ return type; ++} ++ ++static void snd_rpi_hifiberry_dacplusadcpro_set_sclk(struct snd_soc_component *component, ++ int sample_rate) ++{ ++ struct pcm512x_priv *pcm512x = snd_soc_component_get_drvdata(component); ++ ++ if (!IS_ERR(pcm512x->sclk)) { ++ int ctype; ++ ++ ctype = snd_rpi_hifiberry_dacplusadcpro_clk_for_rate(sample_rate); ++ clk_set_rate(pcm512x->sclk, (ctype == HIFIBERRY_DACPRO_CLK44EN) ++ ? CLK_44EN_RATE : CLK_48EN_RATE); ++ snd_rpi_hifiberry_dacplusadcpro_select_clk(component, ctype); ++ } ++} ++ ++static int snd_rpi_hifiberry_dacplusadcpro_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_component *dac = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_component *adc = asoc_rtd_to_codec(rtd, 1)->component; ++ struct snd_soc_dai_driver *adc_driver = asoc_rtd_to_codec(rtd, 1)->driver; ++ struct pcm512x_priv *priv; ++ int ret; ++ ++ if (slave) ++ snd_rpi_hifiberry_is_dacpro = false; ++ else ++ snd_rpi_hifiberry_is_dacpro = ++ snd_rpi_hifiberry_dacplusadcpro_is_pro_card(dac); ++ ++ if (snd_rpi_hifiberry_is_dacpro) { ++ struct snd_soc_dai_link *dai = rtd->dai_link; ++ ++ dai->name = "HiFiBerry DAC+ADC Pro"; ++ dai->stream_name = "HiFiBerry DAC+ADC Pro HiFi"; ++ dai->dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF ++ | SND_SOC_DAIFMT_CBM_CFM; ++ ++ // set DAC DAI configuration ++ ret = snd_soc_dai_set_fmt(asoc_rtd_to_codec(rtd, 0), ++ SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF ++ | SND_SOC_DAIFMT_CBM_CFM); ++ if (ret < 0) ++ return ret; ++ ++ // set ADC DAI configuration ++ ret = snd_soc_dai_set_fmt(asoc_rtd_to_codec(rtd, 1), ++ SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF ++ | SND_SOC_DAIFMT_CBS_CFS); ++ if (ret < 0) ++ return ret; ++ ++ // set CPU DAI configuration ++ ret = snd_soc_dai_set_fmt(asoc_rtd_to_cpu(rtd, 0), ++ SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | SND_SOC_DAIFMT_CBS_CFS); ++ if (ret < 0) ++ return ret; ++ ++ snd_soc_component_update_bits(dac, PCM512x_BCLK_LRCLK_CFG, 0x31, 0x11); ++ snd_soc_component_update_bits(dac, PCM512x_MASTER_MODE, 0x03, 0x03); ++ snd_soc_component_update_bits(dac, PCM512x_MASTER_CLKDIV_2, 0x7f, 63); ++ } else { ++ priv = snd_soc_component_get_drvdata(dac); ++ priv->sclk = ERR_PTR(-ENOENT); ++ } ++ ++ /* disable 24bit mode as long as I2S module does not have sign extension fixed */ ++ adc_driver->capture.formats = SNDRV_PCM_FMTBIT_S32_LE | SNDRV_PCM_FMTBIT_S16_LE; ++ ++ snd_soc_component_update_bits(dac, PCM512x_GPIO_EN, 0x08, 0x08); ++ snd_soc_component_update_bits(dac, PCM512x_GPIO_OUTPUT_4, 0x0f, 0x02); ++ if (leds_off) ++ snd_soc_component_update_bits(dac, PCM512x_GPIO_CONTROL_1, 0x08, 0x00); ++ else ++ snd_soc_component_update_bits(dac, PCM512x_GPIO_CONTROL_1, 0x08, 0x08); ++ ++ ret = pcm1863_add_controls(adc); ++ if (ret < 0) ++ dev_warn(rtd->dev, "Failed to add pcm1863 controls: %d\n", ++ ret); ++ ++ /* set GPIO2 to output, GPIO3 input */ ++ snd_soc_component_write(adc, PCM186X_GPIO3_2_CTRL, 0x00); ++ snd_soc_component_write(adc, PCM186X_GPIO3_2_DIR_CTRL, 0x04); ++ if (leds_off) ++ snd_soc_component_update_bits(adc, PCM186X_GPIO_IN_OUT, 0x40, 0x00); ++ else ++ snd_soc_component_update_bits(adc, PCM186X_GPIO_IN_OUT, 0x40, 0x40); ++ ++ if (digital_gain_0db_limit) { ++ int ret; ++ struct snd_soc_card *card = rtd->card; ++ ++ ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207); ++ if (ret < 0) ++ dev_warn(card->dev, "Failed to set volume limit: %d\n", ret); ++ } ++ ++ return 0; ++} ++ ++static int snd_rpi_hifiberry_dacplusadcpro_update_rate_den( ++ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; /* only use DAC */ ++ struct pcm512x_priv *pcm512x = snd_soc_component_get_drvdata(component); ++ struct snd_ratnum *rats_no_pll; ++ unsigned int num = 0, den = 0; ++ int err; ++ ++ rats_no_pll = devm_kzalloc(rtd->dev, sizeof(*rats_no_pll), GFP_KERNEL); ++ if (!rats_no_pll) ++ return -ENOMEM; ++ ++ rats_no_pll->num = clk_get_rate(pcm512x->sclk) / 64; ++ rats_no_pll->den_min = 1; ++ rats_no_pll->den_max = 128; ++ rats_no_pll->den_step = 1; ++ ++ err = snd_interval_ratnum(hw_param_interval(params, ++ SNDRV_PCM_HW_PARAM_RATE), 1, rats_no_pll, &num, &den); ++ if (err >= 0 && den) { ++ params->rate_num = num; ++ params->rate_den = den; ++ } ++ ++ devm_kfree(rtd->dev, rats_no_pll); ++ return 0; ++} ++ ++static int snd_rpi_hifiberry_dacplusadcpro_hw_params( ++ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params) ++{ ++ int ret = 0; ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ int channels = params_channels(params); ++ int width = 32; ++ struct snd_soc_component *dac = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_dai *dai = asoc_rtd_to_codec(rtd, 0); ++ struct snd_soc_dai_driver *drv = dai->driver; ++ const struct snd_soc_dai_ops *ops = drv->ops; ++ ++ if (snd_rpi_hifiberry_is_dacpro) { ++ width = snd_pcm_format_physical_width(params_format(params)); ++ ++ snd_rpi_hifiberry_dacplusadcpro_set_sclk(dac, ++ params_rate(params)); ++ ++ ret = snd_rpi_hifiberry_dacplusadcpro_update_rate_den( ++ substream, params); ++ if (ret) ++ return ret; ++ } ++ ++ ret = snd_soc_dai_set_bclk_ratio(asoc_rtd_to_cpu(rtd, 0), channels * width); ++ if (ret) ++ return ret; ++ ret = snd_soc_dai_set_bclk_ratio(asoc_rtd_to_codec(rtd, 0), channels * width); ++ if (ret) ++ return ret; ++ if (snd_rpi_hifiberry_is_dacpro && ops->hw_params) ++ ret = ops->hw_params(substream, params, dai); ++ return ret; ++} ++ ++static int snd_rpi_hifiberry_dacplusadcpro_startup( ++ struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *dac = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_component *adc = asoc_rtd_to_codec(rtd, 1)->component; ++ ++ if (leds_off) ++ return 0; ++ /* switch on respective LED */ ++ if (!substream->stream) ++ snd_soc_component_update_bits(dac, PCM512x_GPIO_CONTROL_1, 0x08, 0x08); ++ else ++ snd_soc_component_update_bits(adc, PCM186X_GPIO_IN_OUT, 0x40, 0x40); ++ return 0; ++} ++ ++static void snd_rpi_hifiberry_dacplusadcpro_shutdown( ++ struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *dac = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_component *adc = asoc_rtd_to_codec(rtd, 1)->component; ++ ++ /* switch off respective LED */ ++ if (!substream->stream) ++ snd_soc_component_update_bits(dac, PCM512x_GPIO_CONTROL_1, 0x08, 0x00); ++ else ++ snd_soc_component_update_bits(adc, PCM186X_GPIO_IN_OUT, 0x40, 0x00); ++} ++ ++ ++/* machine stream operations */ ++static struct snd_soc_ops snd_rpi_hifiberry_dacplusadcpro_ops = { ++ .hw_params = snd_rpi_hifiberry_dacplusadcpro_hw_params, ++ .startup = snd_rpi_hifiberry_dacplusadcpro_startup, ++ .shutdown = snd_rpi_hifiberry_dacplusadcpro_shutdown, ++}; ++ ++SND_SOC_DAILINK_DEFS(hifi, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("pcm512x.1-004d", "pcm512x-hifi"), ++ COMP_CODEC("pcm186x.1-004a", "pcm1863-aif")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_rpi_hifiberry_dacplusadcpro_dai[] = { ++{ ++ .name = "HiFiBerry DAC+ADC PRO", ++ .stream_name = "HiFiBerry DAC+ADC PRO HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ .ops = &snd_rpi_hifiberry_dacplusadcpro_ops, ++ .init = snd_rpi_hifiberry_dacplusadcpro_init, ++ SND_SOC_DAILINK_REG(hifi), ++}, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_rpi_hifiberry_dacplusadcpro = { ++ .name = "snd_rpi_hifiberry_dacplusadcpro", ++ .driver_name = "HifiberryDacpAdcPro", ++ .owner = THIS_MODULE, ++ .dai_link = snd_rpi_hifiberry_dacplusadcpro_dai, ++ .num_links = ARRAY_SIZE(snd_rpi_hifiberry_dacplusadcpro_dai), ++}; ++ ++static int snd_rpi_hifiberry_dacplusadcpro_probe(struct platform_device *pdev) ++{ ++ int ret = 0, i = 0; ++ struct snd_soc_card *card = &snd_rpi_hifiberry_dacplusadcpro; ++ ++ snd_rpi_hifiberry_dacplusadcpro.dev = &pdev->dev; ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai; ++ ++ dai = &snd_rpi_hifiberry_dacplusadcpro_dai[0]; ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ if (i2s_node) { ++ for (i = 0; i < card->num_links; i++) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } ++ } ++ } ++ digital_gain_0db_limit = !of_property_read_bool( ++ pdev->dev.of_node, "hifiberry-dacplusadcpro,24db_digital_gain"); ++ slave = of_property_read_bool(pdev->dev.of_node, ++ "hifiberry-dacplusadcpro,slave"); ++ leds_off = of_property_read_bool(pdev->dev.of_node, ++ "hifiberry-dacplusadcpro,leds_off"); ++ ret = snd_soc_register_card(&snd_rpi_hifiberry_dacplusadcpro); ++ if (ret && ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ ++ return ret; ++} ++ ++static const struct of_device_id snd_rpi_hifiberry_dacplusadcpro_of_match[] = { ++ { .compatible = "hifiberry,hifiberry-dacplusadcpro", }, ++ {}, ++}; ++ ++MODULE_DEVICE_TABLE(of, snd_rpi_hifiberry_dacplusadcpro_of_match); ++ ++static struct platform_driver snd_rpi_hifiberry_dacplusadcpro_driver = { ++ .driver = { ++ .name = "snd-rpi-hifiberry-dacplusadcpro", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_rpi_hifiberry_dacplusadcpro_of_match, ++ }, ++ .probe = snd_rpi_hifiberry_dacplusadcpro_probe, ++}; ++ ++module_platform_driver(snd_rpi_hifiberry_dacplusadcpro_driver); ++ ++MODULE_AUTHOR("Joerg Schambacher "); ++MODULE_AUTHOR("Daniel Matuschek "); ++MODULE_DESCRIPTION("ASoC Driver for HiFiBerry DAC+ADC"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/hifiberry_dacplusdsp.c +@@ -0,0 +1,90 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * ASoC Driver for HiFiBerry DAC + DSP ++ * ++ * Author: Joerg Schambacher ++ * Copyright 2018 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++ ++static struct snd_soc_component_driver dacplusdsp_component_driver; ++ ++static struct snd_soc_dai_driver dacplusdsp_dai = { ++ .name = "dacplusdsp-hifi", ++ .capture = { ++ .stream_name = "DAC+DSP Capture", ++ .channels_min = 2, ++ .channels_max = 2, ++ .rates = SNDRV_PCM_RATE_CONTINUOUS, ++ .formats = SNDRV_PCM_FMTBIT_S16_LE | ++ SNDRV_PCM_FMTBIT_S24_LE | ++ SNDRV_PCM_FMTBIT_S32_LE, ++ }, ++ .playback = { ++ .stream_name = "DACP+DSP Playback", ++ .channels_min = 2, ++ .channels_max = 2, ++ .rates = SNDRV_PCM_RATE_CONTINUOUS, ++ .formats = SNDRV_PCM_FMTBIT_S16_LE | ++ SNDRV_PCM_FMTBIT_S24_LE | ++ SNDRV_PCM_FMTBIT_S32_LE, ++ }, ++ .symmetric_rates = 1}; ++ ++#ifdef CONFIG_OF ++static const struct of_device_id dacplusdsp_ids[] = { ++ { ++ .compatible = "hifiberry,dacplusdsp", ++ }, ++ {} }; ++MODULE_DEVICE_TABLE(of, dacplusdsp_ids); ++#endif ++ ++static int dacplusdsp_platform_probe(struct platform_device *pdev) ++{ ++ int ret; ++ ++ ret = snd_soc_register_component(&pdev->dev, ++ &dacplusdsp_component_driver, &dacplusdsp_dai, 1); ++ if (ret) { ++ pr_alert("snd_soc_register_component failed\n"); ++ return ret; ++ } ++ ++ return 0; ++} ++ ++static int dacplusdsp_platform_remove(struct platform_device *pdev) ++{ ++ snd_soc_unregister_component(&pdev->dev); ++ return 0; ++} ++ ++static struct platform_driver dacplusdsp_driver = { ++ .driver = { ++ .name = "hifiberry-dacplusdsp-codec", ++ .of_match_table = of_match_ptr(dacplusdsp_ids), ++ }, ++ .probe = dacplusdsp_platform_probe, ++ .remove = dacplusdsp_platform_remove, ++}; ++ ++module_platform_driver(dacplusdsp_driver); ++ ++MODULE_AUTHOR("Joerg Schambacher "); ++MODULE_DESCRIPTION("ASoC Driver for HiFiBerry DAC+DSP"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/hifiberry_dacplushd.c +@@ -0,0 +1,238 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * ASoC Driver for HiFiBerry DAC+ HD ++ * ++ * Author: Joerg Schambacher, i2Audio GmbH for HiFiBerry ++ * Copyright 2020 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "../codecs/pcm179x.h" ++ ++#define DEFAULT_RATE 44100 ++ ++struct brd_drv_data { ++ struct regmap *regmap; ++ struct clk *sclk; ++}; ++ ++static struct brd_drv_data drvdata; ++static struct gpio_desc *reset_gpio; ++static const unsigned int hb_dacplushd_rates[] = { ++ 192000, 96000, 48000, 176400, 88200, 44100, ++}; ++ ++static struct snd_pcm_hw_constraint_list hb_dacplushd_constraints = { ++ .list = hb_dacplushd_rates, ++ .count = ARRAY_SIZE(hb_dacplushd_rates), ++}; ++ ++static int snd_rpi_hb_dacplushd_startup(struct snd_pcm_substream *substream) ++{ ++ /* constraints for standard sample rates */ ++ snd_pcm_hw_constraint_list(substream->runtime, 0, ++ SNDRV_PCM_HW_PARAM_RATE, ++ &hb_dacplushd_constraints); ++ return 0; ++} ++ ++static void snd_rpi_hifiberry_dacplushd_set_sclk( ++ struct snd_soc_component *component, ++ int sample_rate) ++{ ++ if (!IS_ERR(drvdata.sclk)) ++ clk_set_rate(drvdata.sclk, sample_rate); ++} ++ ++static int snd_rpi_hifiberry_dacplushd_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_dai_link *dai = rtd->dai_link; ++ struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0); ++ ++ dai->name = "HiFiBerry DAC+ HD"; ++ dai->stream_name = "HiFiBerry DAC+ HD HiFi"; ++ dai->dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF ++ | SND_SOC_DAIFMT_CBM_CFM; ++ ++ /* allow only fixed 32 clock counts per channel */ ++ snd_soc_dai_set_bclk_ratio(cpu_dai, 32*2); ++ ++ return 0; ++} ++ ++static int snd_rpi_hifiberry_dacplushd_hw_params( ++ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params) ++{ ++ int ret = 0; ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ ++ snd_rpi_hifiberry_dacplushd_set_sclk(component, params_rate(params)); ++ return ret; ++} ++ ++/* machine stream operations */ ++static struct snd_soc_ops snd_rpi_hifiberry_dacplushd_ops = { ++ .startup = snd_rpi_hb_dacplushd_startup, ++ .hw_params = snd_rpi_hifiberry_dacplushd_hw_params, ++}; ++ ++SND_SOC_DAILINK_DEFS(hifi, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("pcm179x.1-004c", "pcm179x-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++ ++static struct snd_soc_dai_link snd_rpi_hifiberry_dacplushd_dai[] = { ++{ ++ .name = "HiFiBerry DAC+ HD", ++ .stream_name = "HiFiBerry DAC+ HD HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ .ops = &snd_rpi_hifiberry_dacplushd_ops, ++ .init = snd_rpi_hifiberry_dacplushd_init, ++ SND_SOC_DAILINK_REG(hifi), ++}, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_rpi_hifiberry_dacplushd = { ++ .name = "snd_rpi_hifiberry_dacplushd", ++ .driver_name = "HifiberryDacplusHD", ++ .owner = THIS_MODULE, ++ .dai_link = snd_rpi_hifiberry_dacplushd_dai, ++ .num_links = ARRAY_SIZE(snd_rpi_hifiberry_dacplushd_dai), ++}; ++ ++static int snd_rpi_hifiberry_dacplushd_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ static int dac_reset_done; ++ struct device *dev = &pdev->dev; ++ struct device_node *dev_node = dev->of_node; ++ ++ snd_rpi_hifiberry_dacplushd.dev = &pdev->dev; ++ ++ /* get GPIO and release DAC from RESET */ ++ if (!dac_reset_done) { ++ reset_gpio = gpiod_get(&pdev->dev, "reset", GPIOD_OUT_LOW); ++ if (IS_ERR(reset_gpio)) { ++ dev_err(&pdev->dev, "gpiod_get() failed\n"); ++ return -EINVAL; ++ } ++ dac_reset_done = 1; ++ } ++ if (!IS_ERR(reset_gpio)) ++ gpiod_set_value(reset_gpio, 0); ++ msleep(1); ++ if (!IS_ERR(reset_gpio)) ++ gpiod_set_value(reset_gpio, 1); ++ msleep(1); ++ if (!IS_ERR(reset_gpio)) ++ gpiod_set_value(reset_gpio, 0); ++ ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai; ++ ++ dai = &snd_rpi_hifiberry_dacplushd_dai[0]; ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ ++ if (i2s_node) { ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->of_node = i2s_node; ++ dai->cpus->dai_name = NULL; ++ dai->platforms->name = NULL; ++ } else { ++ return -EPROBE_DEFER; ++ } ++ ++ } ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, ++ &snd_rpi_hifiberry_dacplushd); ++ if (ret && ret != -EPROBE_DEFER) { ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ return ret; ++ } ++ if (ret == -EPROBE_DEFER) ++ return ret; ++ ++ dev_set_drvdata(dev, &drvdata); ++ if (dev_node == NULL) { ++ dev_err(&pdev->dev, "Device tree node not found\n"); ++ return -ENODEV; ++ } ++ ++ drvdata.sclk = devm_clk_get(dev, NULL); ++ if (IS_ERR(drvdata.sclk)) { ++ drvdata.sclk = ERR_PTR(-ENOENT); ++ return -ENODEV; ++ } ++ ++ clk_set_rate(drvdata.sclk, DEFAULT_RATE); ++ ++ return ret; ++} ++ ++static int snd_rpi_hifiberry_dacplushd_remove(struct platform_device *pdev) ++{ ++ if (IS_ERR(reset_gpio)) ++ return -EINVAL; ++ ++ /* put DAC into RESET and release GPIO */ ++ gpiod_set_value(reset_gpio, 0); ++ gpiod_put(reset_gpio); ++ ++ return 0; ++} ++ ++static const struct of_device_id snd_rpi_hifiberry_dacplushd_of_match[] = { ++ { .compatible = "hifiberry,hifiberry-dacplushd", }, ++ {}, ++}; ++ ++MODULE_DEVICE_TABLE(of, snd_rpi_hifiberry_dacplushd_of_match); ++ ++static struct platform_driver snd_rpi_hifiberry_dacplushd_driver = { ++ .driver = { ++ .name = "snd-rpi-hifiberry-dacplushd", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_rpi_hifiberry_dacplushd_of_match, ++ }, ++ .probe = snd_rpi_hifiberry_dacplushd_probe, ++ .remove = snd_rpi_hifiberry_dacplushd_remove, ++}; ++ ++module_platform_driver(snd_rpi_hifiberry_dacplushd_driver); ++ ++MODULE_AUTHOR("Joerg Schambacher "); ++MODULE_DESCRIPTION("ASoC Driver for HiFiBerry DAC+ HD"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/i-sabre-q2m.c +@@ -0,0 +1,158 @@ ++/* ++ * ASoC Driver for I-Sabre Q2M ++ * ++ * Author: Satoru Kawase ++ * Modified by: Xiao Qingyong ++ * Update kernel v4.18+ by : Audiophonics ++ * Copyright 2018 Audiophonics ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "../codecs/i-sabre-codec.h" ++ ++ ++static int snd_rpi_i_sabre_q2m_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ unsigned int value; ++ ++ /* Device ID */ ++ value = snd_soc_component_read(component, ISABRECODEC_REG_01); ++ dev_info(component->card->dev, "Audiophonics Device ID : %02X\n", value); ++ ++ /* API revision */ ++ value = snd_soc_component_read(component, ISABRECODEC_REG_02); ++ dev_info(component->card->dev, "Audiophonics API revision : %02X\n", value); ++ ++ return 0; ++} ++ ++static int snd_rpi_i_sabre_q2m_hw_params( ++ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0); ++ int bclk_ratio; ++ ++ bclk_ratio = snd_pcm_format_physical_width( ++ params_format(params)) * params_channels(params); ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, bclk_ratio); ++} ++ ++/* machine stream operations */ ++static struct snd_soc_ops snd_rpi_i_sabre_q2m_ops = { ++ .hw_params = snd_rpi_i_sabre_q2m_hw_params, ++}; ++ ++SND_SOC_DAILINK_DEFS(rpi_i_sabre_q2m, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("i-sabre-codec-i2c.1-0048", "i-sabre-codec-dai")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_rpi_i_sabre_q2m_dai[] = { ++ { ++ .name = "I-Sabre Q2M", ++ .stream_name = "I-Sabre Q2M DAC", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF ++ | SND_SOC_DAIFMT_CBS_CFS, ++ .init = snd_rpi_i_sabre_q2m_init, ++ .ops = &snd_rpi_i_sabre_q2m_ops, ++ SND_SOC_DAILINK_REG(rpi_i_sabre_q2m), ++ } ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_rpi_i_sabre_q2m = { ++ .name = "I-Sabre Q2M DAC", ++ .owner = THIS_MODULE, ++ .dai_link = snd_rpi_i_sabre_q2m_dai, ++ .num_links = ARRAY_SIZE(snd_rpi_i_sabre_q2m_dai) ++}; ++ ++ ++static int snd_rpi_i_sabre_q2m_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ ++ snd_rpi_i_sabre_q2m.dev = &pdev->dev; ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai; ++ ++ dai = &snd_rpi_i_sabre_q2m_dai[0]; ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ if (i2s_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } else { ++ dev_err(&pdev->dev, ++ "Property 'i2s-controller' missing or invalid\n"); ++ return (-EINVAL); ++ } ++ ++ dai->name = "I-Sabre Q2M"; ++ dai->stream_name = "I-Sabre Q2M DAC"; ++ dai->dai_fmt = SND_SOC_DAIFMT_I2S ++ | SND_SOC_DAIFMT_NB_NF ++ | SND_SOC_DAIFMT_CBS_CFS; ++ } ++ ++ /* Wait for registering codec driver */ ++ mdelay(50); ++ ++ ret = snd_soc_register_card(&snd_rpi_i_sabre_q2m); ++ if (ret) { ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ } ++ ++ return ret; ++} ++ ++static int snd_rpi_i_sabre_q2m_remove(struct platform_device *pdev) ++{ ++ return snd_soc_unregister_card(&snd_rpi_i_sabre_q2m); ++} ++ ++static const struct of_device_id snd_rpi_i_sabre_q2m_of_match[] = { ++ { .compatible = "audiophonics,i-sabre-q2m", }, ++ {} ++}; ++MODULE_DEVICE_TABLE(of, snd_rpi_i_sabre_q2m_of_match); ++ ++static struct platform_driver snd_rpi_i_sabre_q2m_driver = { ++ .driver = { ++ .name = "snd-rpi-i-sabre-q2m", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_rpi_i_sabre_q2m_of_match, ++ }, ++ .probe = snd_rpi_i_sabre_q2m_probe, ++ .remove = snd_rpi_i_sabre_q2m_remove, ++}; ++module_platform_driver(snd_rpi_i_sabre_q2m_driver); ++ ++MODULE_DESCRIPTION("ASoC Driver for I-Sabre Q2M"); ++MODULE_AUTHOR("Audiophonics "); ++MODULE_LICENSE("GPL"); +--- /dev/null ++++ b/sound/soc/bcm/iqaudio-codec.c +@@ -0,0 +1,274 @@ ++/* ++ * ASoC Driver for IQaudIO Raspberry Pi Codec board ++ * ++ * Author: Gordon Garrity ++ * (C) Copyright IQaudio Limited, 2017-2019 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include "../codecs/da7213.h" ++ ++static int pll_out = DA7213_PLL_FREQ_OUT_90316800; ++ ++static int snd_rpi_iqaudio_pll_control(struct snd_soc_dapm_widget *w, ++ struct snd_kcontrol *k, int event) ++{ ++ int ret = 0; ++ struct snd_soc_dapm_context *dapm = w->dapm; ++ struct snd_soc_card *card = dapm->card; ++ struct snd_soc_pcm_runtime *rtd = ++ snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ struct snd_soc_dai *codec_dai = asoc_rtd_to_codec(rtd, 0); ++ ++ if (SND_SOC_DAPM_EVENT_OFF(event)) { ++ ret = snd_soc_dai_set_pll(codec_dai, 0, DA7213_SYSCLK_MCLK, 0, ++ 0); ++ if (ret) ++ dev_err(card->dev, "Failed to bypass PLL: %d\n", ret); ++ /* Allow PLL time to bypass */ ++ msleep(100); ++ } else if (SND_SOC_DAPM_EVENT_ON(event)) { ++ ret = snd_soc_dai_set_pll(codec_dai, 0, DA7213_SYSCLK_PLL, 0, ++ pll_out); ++ if (ret) ++ dev_err(card->dev, "Failed to enable PLL: %d\n", ret); ++ /* Allow PLL time to lock */ ++ msleep(100); ++ } ++ ++ return ret; ++} ++ ++static int snd_rpi_iqaudio_post_dapm_event(struct snd_soc_dapm_widget *w, ++ struct snd_kcontrol *kcontrol, ++ int event) ++{ ++ switch (event) { ++ case SND_SOC_DAPM_POST_PMU: ++ /* Delay for mic bias ramp */ ++ msleep(1000); ++ break; ++ default: ++ break; ++ } ++ ++ return 0; ++} ++ ++static const struct snd_kcontrol_new dapm_controls[] = { ++ SOC_DAPM_PIN_SWITCH("HP Jack"), ++ SOC_DAPM_PIN_SWITCH("MIC Jack"), ++ SOC_DAPM_PIN_SWITCH("Onboard MIC"), ++ SOC_DAPM_PIN_SWITCH("AUX Jack"), ++}; ++ ++static const struct snd_soc_dapm_widget dapm_widgets[] = { ++ SND_SOC_DAPM_HP("HP Jack", NULL), ++ SND_SOC_DAPM_MIC("MIC Jack", NULL), ++ SND_SOC_DAPM_MIC("Onboard MIC", NULL), ++ SND_SOC_DAPM_LINE("AUX Jack", NULL), ++ SND_SOC_DAPM_SUPPLY("PLL Control", SND_SOC_NOPM, 0, 0, ++ snd_rpi_iqaudio_pll_control, ++ SND_SOC_DAPM_PRE_PMU | SND_SOC_DAPM_POST_PMD), ++ SND_SOC_DAPM_POST("Post Power Up Event", snd_rpi_iqaudio_post_dapm_event), ++}; ++ ++static const struct snd_soc_dapm_route audio_map[] = { ++ {"HP Jack", NULL, "HPL"}, ++ {"HP Jack", NULL, "HPR"}, ++ {"HP Jack", NULL, "PLL Control"}, ++ ++ {"AUXR", NULL, "AUX Jack"}, ++ {"AUXL", NULL, "AUX Jack"}, ++ {"AUX Jack", NULL, "PLL Control"}, ++ ++ /* Assume Mic1 is linked to Headset and Mic2 to on-board mic */ ++ {"MIC1", NULL, "MIC Jack"}, ++ {"MIC Jack", NULL, "PLL Control"}, ++ {"MIC2", NULL, "Onboard MIC"}, ++ {"Onboard MIC", NULL, "PLL Control"}, ++}; ++ ++/* machine stream operations */ ++ ++static int snd_rpi_iqaudio_codec_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_dai *codec_dai = asoc_rtd_to_codec(rtd, 0); ++ struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0); ++ int ret; ++ ++ /* ++ * Disable AUX Jack Pin by default to prevent PLL being enabled at ++ * startup. This avoids holding the PLL to a fixed SR config for ++ * subsequent streams. ++ * ++ * This pin can still be enabled later, as required by user-space. ++ */ ++ snd_soc_dapm_disable_pin(&rtd->card->dapm, "AUX Jack"); ++ snd_soc_dapm_sync(&rtd->card->dapm); ++ ++ /* Set bclk ratio to align with codec's BCLK rate */ ++ ret = snd_soc_dai_set_bclk_ratio(cpu_dai, 64); ++ if (ret) { ++ dev_err(rtd->dev, "Failed to set CPU BLCK ratio\n"); ++ return ret; ++ } ++ ++ /* Set MCLK frequency to codec, onboard 11.2896MHz clock */ ++ return snd_soc_dai_set_sysclk(codec_dai, DA7213_CLKSRC_MCLK, 11289600, ++ SND_SOC_CLOCK_OUT); ++} ++ ++static int snd_rpi_iqaudio_codec_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ unsigned int samplerate = params_rate(params); ++ ++ switch (samplerate) { ++ case 8000: ++ case 16000: ++ case 32000: ++ case 48000: ++ case 96000: ++ pll_out = DA7213_PLL_FREQ_OUT_98304000; ++ return 0; ++ case 44100: ++ case 88200: ++ pll_out = DA7213_PLL_FREQ_OUT_90316800; ++ return 0; ++ default: ++ dev_err(rtd->dev,"Unsupported samplerate %d\n", samplerate); ++ return -EINVAL; ++ } ++} ++ ++static const struct snd_soc_ops snd_rpi_iqaudio_codec_ops = { ++ .hw_params = snd_rpi_iqaudio_codec_hw_params, ++}; ++ ++SND_SOC_DAILINK_DEFS(rpi_iqaudio, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("da7213.1-001a", "da7213-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2835-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_rpi_iqaudio_codec_dai[] = { ++{ ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBM_CFM, ++ .init = snd_rpi_iqaudio_codec_init, ++ .ops = &snd_rpi_iqaudio_codec_ops, ++ .symmetric_rates = 1, ++ .symmetric_channels = 1, ++ .symmetric_samplebits = 1, ++ SND_SOC_DAILINK_REG(rpi_iqaudio), ++}, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_rpi_iqaudio_codec = { ++ .owner = THIS_MODULE, ++ .dai_link = snd_rpi_iqaudio_codec_dai, ++ .num_links = ARRAY_SIZE(snd_rpi_iqaudio_codec_dai), ++ .controls = dapm_controls, ++ .num_controls = ARRAY_SIZE(dapm_controls), ++ .dapm_widgets = dapm_widgets, ++ .num_dapm_widgets = ARRAY_SIZE(dapm_widgets), ++ .dapm_routes = audio_map, ++ .num_dapm_routes = ARRAY_SIZE(audio_map), ++}; ++ ++static int snd_rpi_iqaudio_codec_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ ++ snd_rpi_iqaudio_codec.dev = &pdev->dev; ++ ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_card *card = &snd_rpi_iqaudio_codec; ++ struct snd_soc_dai_link *dai = &snd_rpi_iqaudio_codec_dai[0]; ++ ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ if (i2s_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } ++ ++ if (of_property_read_string(pdev->dev.of_node, "card_name", ++ &card->name)) ++ card->name = "IQaudIOCODEC"; ++ ++ if (of_property_read_string(pdev->dev.of_node, "dai_name", ++ &dai->name)) ++ dai->name = "IQaudIO CODEC"; ++ ++ if (of_property_read_string(pdev->dev.of_node, ++ "dai_stream_name", &dai->stream_name)) ++ dai->stream_name = "IQaudIO CODEC HiFi v1.2"; ++ ++ } ++ ++ ret = snd_soc_register_card(&snd_rpi_iqaudio_codec); ++ if (ret) { ++ if (ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ return ret; ++ } ++ ++ return 0; ++} ++ ++static int snd_rpi_iqaudio_codec_remove(struct platform_device *pdev) ++{ ++ return snd_soc_unregister_card(&snd_rpi_iqaudio_codec); ++} ++ ++static const struct of_device_id iqaudio_of_match[] = { ++ { .compatible = "iqaudio,iqaudio-codec", }, ++ {}, ++}; ++ ++MODULE_DEVICE_TABLE(of, iqaudio_of_match); ++ ++static struct platform_driver snd_rpi_iqaudio_codec_driver = { ++ .driver = { ++ .name = "snd-rpi-iqaudio-codec", ++ .owner = THIS_MODULE, ++ .of_match_table = iqaudio_of_match, ++ }, ++ .probe = snd_rpi_iqaudio_codec_probe, ++ .remove = snd_rpi_iqaudio_codec_remove, ++}; ++ ++ ++ ++module_platform_driver(snd_rpi_iqaudio_codec_driver); ++ ++MODULE_AUTHOR("Gordon Garrity "); ++MODULE_DESCRIPTION("ASoC Driver for IQaudIO CODEC"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/iqaudio-dac.c +@@ -0,0 +1,223 @@ ++/* ++ * ASoC Driver for IQaudIO DAC ++ * ++ * Author: Florian Meier ++ * Copyright 2013 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++ ++static bool digital_gain_0db_limit = true; ++ ++static struct gpio_desc *mute_gpio; ++ ++static int snd_rpi_iqaudio_dac_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ if (digital_gain_0db_limit) ++ { ++ int ret; ++ struct snd_soc_card *card = rtd->card; ++ ++ ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207); ++ if (ret < 0) ++ dev_warn(card->dev, "Failed to set volume limit: %d\n", ret); ++ } ++ ++ return 0; ++} ++ ++static void snd_rpi_iqaudio_gpio_mute(struct snd_soc_card *card) ++{ ++ if (mute_gpio) { ++ dev_info(card->dev, "%s: muting amp using GPIO22\n", ++ __func__); ++ gpiod_set_value_cansleep(mute_gpio, 0); ++ } ++} ++ ++static void snd_rpi_iqaudio_gpio_unmute(struct snd_soc_card *card) ++{ ++ if (mute_gpio) { ++ dev_info(card->dev, "%s: un-muting amp using GPIO22\n", ++ __func__); ++ gpiod_set_value_cansleep(mute_gpio, 1); ++ } ++} ++ ++static int snd_rpi_iqaudio_set_bias_level(struct snd_soc_card *card, ++ struct snd_soc_dapm_context *dapm, enum snd_soc_bias_level level) ++{ ++ struct snd_soc_pcm_runtime *rtd; ++ struct snd_soc_dai *codec_dai; ++ ++ rtd = snd_soc_get_pcm_runtime(card, &card->dai_link[0]); ++ codec_dai = asoc_rtd_to_codec(rtd, 0); ++ ++ if (dapm->dev != codec_dai->dev) ++ return 0; ++ ++ switch (level) { ++ case SND_SOC_BIAS_PREPARE: ++ if (dapm->bias_level != SND_SOC_BIAS_STANDBY) ++ break; ++ ++ /* UNMUTE AMP */ ++ snd_rpi_iqaudio_gpio_unmute(card); ++ ++ break; ++ case SND_SOC_BIAS_STANDBY: ++ if (dapm->bias_level != SND_SOC_BIAS_PREPARE) ++ break; ++ ++ /* MUTE AMP */ ++ snd_rpi_iqaudio_gpio_mute(card); ++ ++ break; ++ default: ++ break; ++ } ++ ++ return 0; ++} ++ ++SND_SOC_DAILINK_DEFS(hifi, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("pcm512x.1-004c", "pcm512x-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_rpi_iqaudio_dac_dai[] = { ++{ ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ .init = snd_rpi_iqaudio_dac_init, ++ SND_SOC_DAILINK_REG(hifi), ++}, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_rpi_iqaudio_dac = { ++ .owner = THIS_MODULE, ++ .dai_link = snd_rpi_iqaudio_dac_dai, ++ .num_links = ARRAY_SIZE(snd_rpi_iqaudio_dac_dai), ++}; ++ ++static int snd_rpi_iqaudio_dac_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ bool gpio_unmute = false; ++ ++ snd_rpi_iqaudio_dac.dev = &pdev->dev; ++ ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_card *card = &snd_rpi_iqaudio_dac; ++ struct snd_soc_dai_link *dai = &snd_rpi_iqaudio_dac_dai[0]; ++ bool auto_gpio_mute = false; ++ ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ if (i2s_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } ++ ++ digital_gain_0db_limit = !of_property_read_bool( ++ pdev->dev.of_node, "iqaudio,24db_digital_gain"); ++ ++ if (of_property_read_string(pdev->dev.of_node, "card_name", ++ &card->name)) ++ card->name = "IQaudIODAC"; ++ ++ if (of_property_read_string(pdev->dev.of_node, "dai_name", ++ &dai->name)) ++ dai->name = "IQaudIO DAC"; ++ ++ if (of_property_read_string(pdev->dev.of_node, ++ "dai_stream_name", &dai->stream_name)) ++ dai->stream_name = "IQaudIO DAC HiFi"; ++ ++ /* gpio_unmute - one time unmute amp using GPIO */ ++ gpio_unmute = of_property_read_bool(pdev->dev.of_node, ++ "iqaudio-dac,unmute-amp"); ++ ++ /* auto_gpio_mute - mute/unmute amp using GPIO */ ++ auto_gpio_mute = of_property_read_bool(pdev->dev.of_node, ++ "iqaudio-dac,auto-mute-amp"); ++ ++ if (auto_gpio_mute || gpio_unmute) { ++ mute_gpio = devm_gpiod_get_optional(&pdev->dev, "mute", ++ GPIOD_OUT_LOW); ++ if (IS_ERR(mute_gpio)) { ++ ret = PTR_ERR(mute_gpio); ++ dev_err(&pdev->dev, ++ "Failed to get mute gpio: %d\n", ret); ++ return ret; ++ } ++ ++ if (auto_gpio_mute && mute_gpio) ++ snd_rpi_iqaudio_dac.set_bias_level = ++ snd_rpi_iqaudio_set_bias_level; ++ } ++ } ++ ++ ret = snd_soc_register_card(&snd_rpi_iqaudio_dac); ++ if (ret) { ++ if (ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ return ret; ++ } ++ ++ if (gpio_unmute && mute_gpio) ++ snd_rpi_iqaudio_gpio_unmute(&snd_rpi_iqaudio_dac); ++ ++ return 0; ++} ++ ++static int snd_rpi_iqaudio_dac_remove(struct platform_device *pdev) ++{ ++ snd_rpi_iqaudio_gpio_mute(&snd_rpi_iqaudio_dac); ++ ++ return snd_soc_unregister_card(&snd_rpi_iqaudio_dac); ++} ++ ++static const struct of_device_id iqaudio_of_match[] = { ++ { .compatible = "iqaudio,iqaudio-dac", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, iqaudio_of_match); ++ ++static struct platform_driver snd_rpi_iqaudio_dac_driver = { ++ .driver = { ++ .name = "snd-rpi-iqaudio-dac", ++ .owner = THIS_MODULE, ++ .of_match_table = iqaudio_of_match, ++ }, ++ .probe = snd_rpi_iqaudio_dac_probe, ++ .remove = snd_rpi_iqaudio_dac_remove, ++}; ++ ++module_platform_driver(snd_rpi_iqaudio_dac_driver); ++ ++MODULE_AUTHOR("Florian Meier "); ++MODULE_DESCRIPTION("ASoC Driver for IQAudio DAC"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/justboom-both.c +@@ -0,0 +1,266 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * rpi--wm8804.c -- ALSA SoC Raspberry Pi soundcard. ++ * ++ * Authors: Johannes Krude ++ * justboom-dac.c ++ * by Milan Neskovic ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++ ++#include "../codecs/wm8804.h" ++#include "../codecs/pcm512x.h" ++ ++ ++static bool digital_gain_0db_limit = true; ++ ++static int snd_rpi_justboom_both_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_component *digi = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_component *dac = asoc_rtd_to_codec(rtd, 1)->component; ++ ++ /* enable TX output */ ++ snd_soc_component_update_bits(digi, WM8804_PWRDN, 0x4, 0x0); ++ ++ snd_soc_component_update_bits(dac, PCM512x_GPIO_EN, 0x08, 0x08); ++ snd_soc_component_update_bits(dac, PCM512x_GPIO_OUTPUT_4, 0xf, 0x02); ++ snd_soc_component_update_bits(dac, PCM512x_GPIO_CONTROL_1, 0x08, 0x08); ++ ++ if (digital_gain_0db_limit) { ++ int ret; ++ struct snd_soc_card *card = rtd->card; ++ ++ ret = snd_soc_limit_volume(card, "Digital Playback Volume", ++ 207); ++ if (ret < 0) ++ dev_warn(card->dev, "Failed to set volume limit: %d\n", ++ ret); ++ } ++ ++ return 0; ++} ++ ++static int snd_rpi_justboom_both_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_dai *codec_dai = asoc_rtd_to_codec(rtd, 0); ++ struct snd_soc_component *digi = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0); ++ ++ int sysclk = 27000000; /* This is fixed on this board */ ++ ++ long mclk_freq = 0; ++ int mclk_div = 1; ++ int sampling_freq = 1; ++ ++ int ret; ++ ++ int samplerate = params_rate(params); ++ ++ if (samplerate <= 96000) { ++ mclk_freq = samplerate*256; ++ mclk_div = WM8804_MCLKDIV_256FS; ++ } else { ++ mclk_freq = samplerate*128; ++ mclk_div = WM8804_MCLKDIV_128FS; ++ } ++ ++ switch (samplerate) { ++ case 32000: ++ sampling_freq = 0x03; ++ break; ++ case 44100: ++ sampling_freq = 0x00; ++ break; ++ case 48000: ++ sampling_freq = 0x02; ++ break; ++ case 88200: ++ sampling_freq = 0x08; ++ break; ++ case 96000: ++ sampling_freq = 0x0a; ++ break; ++ case 176400: ++ sampling_freq = 0x0c; ++ break; ++ case 192000: ++ sampling_freq = 0x0e; ++ break; ++ default: ++ dev_err(rtd->card->dev, ++ "Failed to set WM8804 SYSCLK, unsupported samplerate %d\n", ++ samplerate); ++ } ++ ++ snd_soc_dai_set_clkdiv(codec_dai, WM8804_MCLK_DIV, mclk_div); ++ snd_soc_dai_set_pll(codec_dai, 0, 0, sysclk, mclk_freq); ++ ++ ret = snd_soc_dai_set_sysclk(codec_dai, WM8804_TX_CLKSRC_PLL, ++ sysclk, SND_SOC_CLOCK_OUT); ++ if (ret < 0) { ++ dev_err(rtd->card->dev, ++ "Failed to set WM8804 SYSCLK: %d\n", ret); ++ return ret; ++ } ++ ++ /* Enable TX output */ ++ snd_soc_component_update_bits(digi, WM8804_PWRDN, 0x4, 0x0); ++ ++ /* Power on */ ++ snd_soc_component_update_bits(digi, WM8804_PWRDN, 0x9, 0); ++ ++ /* set sampling frequency status bits */ ++ snd_soc_component_update_bits(digi, WM8804_SPDTX4, 0x0f, sampling_freq); ++ ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, 64); ++} ++ ++static int snd_rpi_justboom_both_startup(struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *digi = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_component *dac = asoc_rtd_to_codec(rtd, 1)->component; ++ ++ /* turn on digital output */ ++ snd_soc_component_update_bits(digi, WM8804_PWRDN, 0x3c, 0x00); ++ ++ snd_soc_component_update_bits(dac, PCM512x_GPIO_CONTROL_1, 0x08, 0x08); ++ ++ return 0; ++} ++ ++static void snd_rpi_justboom_both_shutdown(struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *digi = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_component *dac = asoc_rtd_to_codec(rtd, 1)->component; ++ ++ snd_soc_component_update_bits(dac, PCM512x_GPIO_CONTROL_1, 0x08, 0x00); ++ ++ /* turn off output */ ++ snd_soc_component_update_bits(digi, WM8804_PWRDN, 0x3c, 0x3c); ++} ++ ++/* machine stream operations */ ++static struct snd_soc_ops snd_rpi_justboom_both_ops = { ++ .hw_params = snd_rpi_justboom_both_hw_params, ++ .startup = snd_rpi_justboom_both_startup, ++ .shutdown = snd_rpi_justboom_both_shutdown, ++}; ++ ++SND_SOC_DAILINK_DEFS(rpi_justboom_both, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("pcm512x.1-004d", "pcm512x-hifi"), ++ COMP_CODEC("wm8804.1-003b", "wm8804-spdif")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_rpi_justboom_both_dai[] = { ++{ ++ .name = "JustBoom Digi", ++ .stream_name = "JustBoom Digi HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBM_CFM, ++ .ops = &snd_rpi_justboom_both_ops, ++ .init = snd_rpi_justboom_both_init, ++ SND_SOC_DAILINK_REG(rpi_justboom_both), ++}, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_rpi_justboom_both = { ++ .name = "snd_rpi_justboom_both", ++ .driver_name = "JustBoomBoth", ++ .owner = THIS_MODULE, ++ .dai_link = snd_rpi_justboom_both_dai, ++ .num_links = ARRAY_SIZE(snd_rpi_justboom_both_dai), ++}; ++ ++static int snd_rpi_justboom_both_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ struct snd_soc_card *card = &snd_rpi_justboom_both; ++ ++ snd_rpi_justboom_both.dev = &pdev->dev; ++ ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai = &snd_rpi_justboom_both_dai[0]; ++ ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ ++ if (i2s_node) { ++ int i; ++ ++ for (i = 0; i < card->num_links; i++) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } ++ } ++ ++ digital_gain_0db_limit = !of_property_read_bool( ++ pdev->dev.of_node, "justboom,24db_digital_gain"); ++ } ++ ++ ret = snd_soc_register_card(card); ++ if (ret && ret != -EPROBE_DEFER) { ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ } ++ ++ return ret; ++} ++ ++static int snd_rpi_justboom_both_remove(struct platform_device *pdev) ++{ ++ return snd_soc_unregister_card(&snd_rpi_justboom_both); ++} ++ ++static const struct of_device_id snd_rpi_justboom_both_of_match[] = { ++ { .compatible = "justboom,justboom-both", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, snd_rpi_justboom_both_of_match); ++ ++static struct platform_driver snd_rpi_justboom_both_driver = { ++ .driver = { ++ .name = "snd-rpi-justboom-both", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_rpi_justboom_both_of_match, ++ }, ++ .probe = snd_rpi_justboom_both_probe, ++ .remove = snd_rpi_justboom_both_remove, ++}; ++ ++module_platform_driver(snd_rpi_justboom_both_driver); ++ ++MODULE_AUTHOR("Johannes Krude "); ++MODULE_DESCRIPTION("ASoC Driver for simultaneous use of JustBoom PI Digi & DAC HAT Sound Cards"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/justboom-dac.c +@@ -0,0 +1,147 @@ ++/* ++ * ASoC Driver for JustBoom DAC Raspberry Pi HAT Sound Card ++ * ++ * Author: Milan Neskovic ++ * Copyright 2016 ++ * based on code by Daniel Matuschek ++ * based on code by Florian Meier ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++ ++#include "../codecs/pcm512x.h" ++ ++static bool digital_gain_0db_limit = true; ++ ++static int snd_rpi_justboom_dac_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ snd_soc_component_update_bits(component, PCM512x_GPIO_EN, 0x08, 0x08); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_OUTPUT_4, 0xf, 0x02); ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x08,0x08); ++ ++ if (digital_gain_0db_limit) ++ { ++ int ret; ++ struct snd_soc_card *card = rtd->card; ++ ++ ret = snd_soc_limit_volume(card, "Digital Playback Volume", 207); ++ if (ret < 0) ++ dev_warn(card->dev, "Failed to set volume limit: %d\n", ret); ++ } ++ ++ return 0; ++} ++ ++static int snd_rpi_justboom_dac_startup(struct snd_pcm_substream *substream) { ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x08,0x08); ++ return 0; ++} ++ ++static void snd_rpi_justboom_dac_shutdown(struct snd_pcm_substream *substream) { ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ snd_soc_component_update_bits(component, PCM512x_GPIO_CONTROL_1, 0x08,0x00); ++} ++ ++/* machine stream operations */ ++static struct snd_soc_ops snd_rpi_justboom_dac_ops = { ++ .startup = snd_rpi_justboom_dac_startup, ++ .shutdown = snd_rpi_justboom_dac_shutdown, ++}; ++ ++SND_SOC_DAILINK_DEFS(hifi, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("pcm512x.1-004d", "pcm512x-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_rpi_justboom_dac_dai[] = { ++{ ++ .name = "JustBoom DAC", ++ .stream_name = "JustBoom DAC HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ .ops = &snd_rpi_justboom_dac_ops, ++ .init = snd_rpi_justboom_dac_init, ++ SND_SOC_DAILINK_REG(hifi), ++}, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_rpi_justboom_dac = { ++ .name = "snd_rpi_justboom_dac", ++ .driver_name = "JustBoomDac", ++ .owner = THIS_MODULE, ++ .dai_link = snd_rpi_justboom_dac_dai, ++ .num_links = ARRAY_SIZE(snd_rpi_justboom_dac_dai), ++}; ++ ++static int snd_rpi_justboom_dac_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ ++ snd_rpi_justboom_dac.dev = &pdev->dev; ++ ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai = &snd_rpi_justboom_dac_dai[0]; ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ ++ if (i2s_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } ++ ++ digital_gain_0db_limit = !of_property_read_bool( ++ pdev->dev.of_node, "justboom,24db_digital_gain"); ++ } ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, &snd_rpi_justboom_dac); ++ if (ret && ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ ++ return ret; ++} ++ ++static const struct of_device_id snd_rpi_justboom_dac_of_match[] = { ++ { .compatible = "justboom,justboom-dac", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, snd_rpi_justboom_dac_of_match); ++ ++static struct platform_driver snd_rpi_justboom_dac_driver = { ++ .driver = { ++ .name = "snd-rpi-justboom-dac", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_rpi_justboom_dac_of_match, ++ }, ++ .probe = snd_rpi_justboom_dac_probe, ++}; ++ ++module_platform_driver(snd_rpi_justboom_dac_driver); ++ ++MODULE_AUTHOR("Milan Neskovic "); ++MODULE_DESCRIPTION("ASoC Driver for JustBoom PI DAC HAT Sound Card"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/pisound.c +@@ -0,0 +1,1238 @@ ++/* ++ * Pisound Linux kernel module. ++ * Copyright (C) 2016-2020 Vilniaus Blokas UAB, https://blokas.io/pisound ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * as published by the Free Software Foundation; version 2 of the ++ * License. ++ * ++ * This program is distributed in the hope that it will be useful, ++ * but WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the ++ * GNU General Public License for more details. ++ * ++ * You should have received a copy of the GNU General Public License ++ * along with this program; if not, write to the Free Software ++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, ++ * MA 02110-1301, USA. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++static int pisnd_spi_init(struct device *dev); ++static void pisnd_spi_uninit(void); ++ ++static void pisnd_spi_flush(void); ++static void pisnd_spi_start(void); ++static uint8_t pisnd_spi_recv(uint8_t *buffer, uint8_t length); ++ ++typedef void (*pisnd_spi_recv_cb)(void *data); ++static void pisnd_spi_set_callback(pisnd_spi_recv_cb cb, void *data); ++ ++static const char *pisnd_spi_get_serial(void); ++static const char *pisnd_spi_get_id(void); ++static const char *pisnd_spi_get_fw_version(void); ++static const char *pisnd_spi_get_hw_version(void); ++ ++static int pisnd_midi_init(struct snd_card *card); ++static void pisnd_midi_uninit(void); ++ ++enum task_e { ++ TASK_PROCESS = 0, ++}; ++ ++static void pisnd_schedule_process(enum task_e task); ++ ++#define PISOUND_LOG_PREFIX "pisound: " ++ ++#ifdef PISOUND_DEBUG ++# define printd(...) pr_alert(PISOUND_LOG_PREFIX __VA_ARGS__) ++#else ++# define printd(...) do {} while (0) ++#endif ++ ++#define printe(...) pr_err(PISOUND_LOG_PREFIX __VA_ARGS__) ++#define printi(...) pr_info(PISOUND_LOG_PREFIX __VA_ARGS__) ++ ++static struct snd_rawmidi *g_rmidi; ++static struct snd_rawmidi_substream *g_midi_output_substream; ++ ++static int pisnd_output_open(struct snd_rawmidi_substream *substream) ++{ ++ g_midi_output_substream = substream; ++ return 0; ++} ++ ++static int pisnd_output_close(struct snd_rawmidi_substream *substream) ++{ ++ g_midi_output_substream = NULL; ++ return 0; ++} ++ ++static void pisnd_output_trigger( ++ struct snd_rawmidi_substream *substream, ++ int up ++ ) ++{ ++ if (substream != g_midi_output_substream) { ++ printe("MIDI output trigger called for an unexpected stream!"); ++ return; ++ } ++ ++ if (!up) ++ return; ++ ++ pisnd_spi_start(); ++} ++ ++static void pisnd_output_drain(struct snd_rawmidi_substream *substream) ++{ ++ pisnd_spi_flush(); ++} ++ ++static int pisnd_input_open(struct snd_rawmidi_substream *substream) ++{ ++ return 0; ++} ++ ++static int pisnd_input_close(struct snd_rawmidi_substream *substream) ++{ ++ return 0; ++} ++ ++static void pisnd_midi_recv_callback(void *substream) ++{ ++ uint8_t data[128]; ++ uint8_t n = 0; ++ ++ while ((n = pisnd_spi_recv(data, sizeof(data)))) { ++ int res = snd_rawmidi_receive(substream, data, n); ++ (void)res; ++ printd("midi recv %u bytes, res = %d\n", n, res); ++ } ++} ++ ++static void pisnd_input_trigger(struct snd_rawmidi_substream *substream, int up) ++{ ++ if (up) { ++ pisnd_spi_set_callback(pisnd_midi_recv_callback, substream); ++ pisnd_schedule_process(TASK_PROCESS); ++ } else { ++ pisnd_spi_set_callback(NULL, NULL); ++ } ++} ++ ++static struct snd_rawmidi_ops pisnd_output_ops = { ++ .open = pisnd_output_open, ++ .close = pisnd_output_close, ++ .trigger = pisnd_output_trigger, ++ .drain = pisnd_output_drain, ++}; ++ ++static struct snd_rawmidi_ops pisnd_input_ops = { ++ .open = pisnd_input_open, ++ .close = pisnd_input_close, ++ .trigger = pisnd_input_trigger, ++}; ++ ++static void pisnd_get_port_info( ++ struct snd_rawmidi *rmidi, ++ int number, ++ struct snd_seq_port_info *seq_port_info ++ ) ++{ ++ seq_port_info->type = ++ SNDRV_SEQ_PORT_TYPE_MIDI_GENERIC | ++ SNDRV_SEQ_PORT_TYPE_HARDWARE | ++ SNDRV_SEQ_PORT_TYPE_PORT; ++ seq_port_info->midi_voices = 0; ++} ++ ++static struct snd_rawmidi_global_ops pisnd_global_ops = { ++ .get_port_info = pisnd_get_port_info, ++}; ++ ++static int pisnd_midi_init(struct snd_card *card) ++{ ++ int err; ++ ++ g_midi_output_substream = NULL; ++ ++ err = snd_rawmidi_new(card, "pisound MIDI", 0, 1, 1, &g_rmidi); ++ ++ if (err < 0) { ++ printe("snd_rawmidi_new failed: %d\n", err); ++ return err; ++ } ++ ++ strcpy(g_rmidi->name, "pisound MIDI "); ++ strcat(g_rmidi->name, pisnd_spi_get_serial()); ++ ++ g_rmidi->info_flags = ++ SNDRV_RAWMIDI_INFO_OUTPUT | ++ SNDRV_RAWMIDI_INFO_INPUT | ++ SNDRV_RAWMIDI_INFO_DUPLEX; ++ ++ g_rmidi->ops = &pisnd_global_ops; ++ ++ g_rmidi->private_data = (void *)0; ++ ++ snd_rawmidi_set_ops( ++ g_rmidi, ++ SNDRV_RAWMIDI_STREAM_OUTPUT, ++ &pisnd_output_ops ++ ); ++ ++ snd_rawmidi_set_ops( ++ g_rmidi, ++ SNDRV_RAWMIDI_STREAM_INPUT, ++ &pisnd_input_ops ++ ); ++ ++ return 0; ++} ++ ++static void pisnd_midi_uninit(void) ++{ ++} ++ ++static void *g_recvData; ++static pisnd_spi_recv_cb g_recvCallback; ++ ++#define FIFO_SIZE 4096 ++ ++static char g_serial_num[11]; ++static char g_id[25]; ++enum { MAX_VERSION_STR_LEN = 6 }; ++static char g_fw_version[MAX_VERSION_STR_LEN]; ++static char g_hw_version[MAX_VERSION_STR_LEN]; ++ ++static uint8_t g_ledFlashDuration; ++static bool g_ledFlashDurationChanged; ++ ++DEFINE_KFIFO(spi_fifo_in, uint8_t, FIFO_SIZE); ++DEFINE_KFIFO(spi_fifo_out, uint8_t, FIFO_SIZE); ++ ++static struct gpio_desc *data_available; ++static struct gpio_desc *spi_reset; ++ ++static struct spi_device *pisnd_spi_device; ++ ++static struct workqueue_struct *pisnd_workqueue; ++static struct work_struct pisnd_work_process; ++ ++static void pisnd_work_handler(struct work_struct *work); ++ ++static void spi_transfer(const uint8_t *txbuf, uint8_t *rxbuf, int len); ++static uint16_t spi_transfer16(uint16_t val); ++ ++static int pisnd_init_workqueues(void) ++{ ++ pisnd_workqueue = create_singlethread_workqueue("pisnd_workqueue"); ++ INIT_WORK(&pisnd_work_process, pisnd_work_handler); ++ ++ return 0; ++} ++ ++static void pisnd_uninit_workqueues(void) ++{ ++ flush_workqueue(pisnd_workqueue); ++ destroy_workqueue(pisnd_workqueue); ++ ++ pisnd_workqueue = NULL; ++} ++ ++static bool pisnd_spi_has_more(void) ++{ ++ return gpiod_get_value(data_available); ++} ++ ++static void pisnd_schedule_process(enum task_e task) ++{ ++ if (pisnd_spi_device != NULL && ++ pisnd_workqueue != NULL && ++ !work_pending(&pisnd_work_process) ++ ) { ++ printd("schedule: has more = %d\n", pisnd_spi_has_more()); ++ if (task == TASK_PROCESS) ++ queue_work(pisnd_workqueue, &pisnd_work_process); ++ } ++} ++ ++static irqreturn_t data_available_interrupt_handler(int irq, void *dev_id) ++{ ++ if (irq == gpiod_to_irq(data_available) && pisnd_spi_has_more()) { ++ printd("schedule from irq\n"); ++ pisnd_schedule_process(TASK_PROCESS); ++ } ++ ++ return IRQ_HANDLED; ++} ++ ++static uint16_t spi_transfer16(uint16_t val) ++{ ++ uint8_t txbuf[2]; ++ uint8_t rxbuf[2]; ++ ++ if (!pisnd_spi_device) { ++ printe("pisnd_spi_device null, returning\n"); ++ return 0; ++ } ++ ++ txbuf[0] = val >> 8; ++ txbuf[1] = val & 0xff; ++ ++ spi_transfer(txbuf, rxbuf, sizeof(txbuf)); ++ ++ printd("received: %02x%02x\n", rxbuf[0], rxbuf[1]); ++ ++ return (rxbuf[0] << 8) | rxbuf[1]; ++} ++ ++static void spi_transfer(const uint8_t *txbuf, uint8_t *rxbuf, int len) ++{ ++ int err; ++ struct spi_transfer transfer; ++ struct spi_message msg; ++ ++ memset(rxbuf, 0, len); ++ ++ if (!pisnd_spi_device) { ++ printe("pisnd_spi_device null, returning\n"); ++ return; ++ } ++ ++ spi_message_init(&msg); ++ ++ memset(&transfer, 0, sizeof(transfer)); ++ ++ transfer.tx_buf = txbuf; ++ transfer.rx_buf = rxbuf; ++ transfer.len = len; ++ transfer.speed_hz = 150000; ++ transfer.delay_usecs = 10; ++ spi_message_add_tail(&transfer, &msg); ++ ++ err = spi_sync(pisnd_spi_device, &msg); ++ ++ if (err < 0) { ++ printe("spi_sync error %d\n", err); ++ return; ++ } ++ ++ printd("hasMore %d\n", pisnd_spi_has_more()); ++} ++ ++static int spi_read_bytes(char *dst, size_t length, uint8_t *bytesRead) ++{ ++ uint16_t rx; ++ uint8_t size; ++ uint8_t i; ++ ++ memset(dst, 0, length); ++ *bytesRead = 0; ++ ++ rx = spi_transfer16(0); ++ if (!(rx >> 8)) ++ return -EINVAL; ++ ++ size = rx & 0xff; ++ ++ if (size > length) ++ return -EINVAL; ++ ++ for (i = 0; i < size; ++i) { ++ rx = spi_transfer16(0); ++ if (!(rx >> 8)) ++ return -EINVAL; ++ ++ dst[i] = rx & 0xff; ++ } ++ ++ *bytesRead = i; ++ ++ return 0; ++} ++ ++static int spi_device_match(struct device *dev, const void *data) ++{ ++ struct spi_device *spi = container_of(dev, struct spi_device, dev); ++ ++ printd(" %s %s %dkHz %d bits mode=0x%02X\n", ++ spi->modalias, dev_name(dev), spi->max_speed_hz/1000, ++ spi->bits_per_word, spi->mode); ++ ++ if (strcmp("pisound-spi", spi->modalias) == 0) { ++ printi("\tFound!\n"); ++ return 1; ++ } ++ ++ printe("\tNot found!\n"); ++ return 0; ++} ++ ++static struct spi_device *pisnd_spi_find_device(void) ++{ ++ struct device *dev; ++ ++ printi("Searching for spi device...\n"); ++ dev = bus_find_device(&spi_bus_type, NULL, NULL, spi_device_match); ++ if (dev != NULL) ++ return container_of(dev, struct spi_device, dev); ++ else ++ return NULL; ++} ++ ++static void pisnd_work_handler(struct work_struct *work) ++{ ++ enum { TRANSFER_SIZE = 4 }; ++ enum { PISOUND_OUTPUT_BUFFER_SIZE_MILLIBYTES = 127 * 1000 }; ++ enum { MIDI_MILLIBYTES_PER_JIFFIE = (3125 * 1000) / HZ }; ++ int out_buffer_used_millibytes = 0; ++ unsigned long now; ++ uint8_t val; ++ uint8_t txbuf[TRANSFER_SIZE]; ++ uint8_t rxbuf[TRANSFER_SIZE]; ++ uint8_t midibuf[TRANSFER_SIZE]; ++ int i, n; ++ bool had_data; ++ ++ unsigned long last_transfer_at = jiffies; ++ ++ if (work == &pisnd_work_process) { ++ if (pisnd_spi_device == NULL) ++ return; ++ ++ do { ++ if (g_midi_output_substream && ++ kfifo_avail(&spi_fifo_out) >= sizeof(midibuf)) { ++ ++ n = snd_rawmidi_transmit_peek( ++ g_midi_output_substream, ++ midibuf, sizeof(midibuf) ++ ); ++ ++ if (n > 0) { ++ for (i = 0; i < n; ++i) ++ kfifo_put( ++ &spi_fifo_out, ++ midibuf[i] ++ ); ++ snd_rawmidi_transmit_ack( ++ g_midi_output_substream, ++ i ++ ); ++ } ++ } ++ ++ had_data = false; ++ memset(txbuf, 0, sizeof(txbuf)); ++ for (i = 0; i < sizeof(txbuf) && ++ ((out_buffer_used_millibytes+1000 < ++ PISOUND_OUTPUT_BUFFER_SIZE_MILLIBYTES) || ++ g_ledFlashDurationChanged); ++ i += 2) { ++ ++ val = 0; ++ ++ if (g_ledFlashDurationChanged) { ++ txbuf[i+0] = 0xf0; ++ txbuf[i+1] = g_ledFlashDuration; ++ g_ledFlashDuration = 0; ++ g_ledFlashDurationChanged = false; ++ } else if (kfifo_get(&spi_fifo_out, &val)) { ++ txbuf[i+0] = 0x0f; ++ txbuf[i+1] = val; ++ out_buffer_used_millibytes += 1000; ++ } ++ } ++ ++ spi_transfer(txbuf, rxbuf, sizeof(txbuf)); ++ /* Estimate the Pisound's MIDI output buffer usage, so ++ * that we don't overflow it. Space in the buffer should ++ * be becoming available at the UART MIDI byte transfer ++ * rate. ++ */ ++ now = jiffies; ++ if (now != last_transfer_at) { ++ out_buffer_used_millibytes -= ++ (now - last_transfer_at) * ++ MIDI_MILLIBYTES_PER_JIFFIE; ++ if (out_buffer_used_millibytes < 0) ++ out_buffer_used_millibytes = 0; ++ last_transfer_at = now; ++ } ++ ++ for (i = 0; i < sizeof(rxbuf); i += 2) { ++ if (rxbuf[i]) { ++ kfifo_put(&spi_fifo_in, rxbuf[i+1]); ++ if (kfifo_len(&spi_fifo_in) > 16 && ++ g_recvCallback) ++ g_recvCallback(g_recvData); ++ had_data = true; ++ } ++ } ++ } while (had_data ++ || !kfifo_is_empty(&spi_fifo_out) ++ || pisnd_spi_has_more() ++ || g_ledFlashDurationChanged ++ || out_buffer_used_millibytes != 0 ++ ); ++ ++ if (!kfifo_is_empty(&spi_fifo_in) && g_recvCallback) ++ g_recvCallback(g_recvData); ++ } ++} ++ ++static int pisnd_spi_gpio_init(struct device *dev) ++{ ++ spi_reset = gpiod_get_index(dev, "reset", 1, GPIOD_ASIS); ++ data_available = gpiod_get_index(dev, "data_available", 0, GPIOD_ASIS); ++ ++ gpiod_direction_output(spi_reset, 1); ++ gpiod_direction_input(data_available); ++ ++ /* Reset the slave. */ ++ gpiod_set_value(spi_reset, false); ++ mdelay(1); ++ gpiod_set_value(spi_reset, true); ++ ++ /* Give time for spi slave to start. */ ++ mdelay(64); ++ ++ return 0; ++} ++ ++static void pisnd_spi_gpio_uninit(void) ++{ ++ gpiod_set_value(spi_reset, false); ++ gpiod_put(spi_reset); ++ spi_reset = NULL; ++ ++ gpiod_put(data_available); ++ data_available = NULL; ++} ++ ++static int pisnd_spi_gpio_irq_init(struct device *dev) ++{ ++ return request_threaded_irq( ++ gpiod_to_irq(data_available), NULL, ++ data_available_interrupt_handler, ++ IRQF_TIMER | IRQF_TRIGGER_RISING | IRQF_ONESHOT, ++ "data_available_int", ++ NULL ++ ); ++} ++ ++static void pisnd_spi_gpio_irq_uninit(void) ++{ ++ free_irq(gpiod_to_irq(data_available), NULL); ++} ++ ++static int spi_read_info(void) ++{ ++ uint16_t tmp; ++ uint8_t count; ++ uint8_t n; ++ uint8_t i; ++ uint8_t j; ++ char buffer[257]; ++ int ret; ++ char *p; ++ ++ memset(g_serial_num, 0, sizeof(g_serial_num)); ++ memset(g_fw_version, 0, sizeof(g_fw_version)); ++ strcpy(g_hw_version, "1.0"); // Assume 1.0 hw version. ++ memset(g_id, 0, sizeof(g_id)); ++ ++ tmp = spi_transfer16(0); ++ ++ if (!(tmp >> 8)) ++ return -EINVAL; ++ ++ count = tmp & 0xff; ++ ++ for (i = 0; i < count; ++i) { ++ memset(buffer, 0, sizeof(buffer)); ++ ret = spi_read_bytes(buffer, sizeof(buffer)-1, &n); ++ ++ if (ret < 0) ++ return ret; ++ ++ switch (i) { ++ case 0: ++ if (n != 2) ++ return -EINVAL; ++ ++ snprintf( ++ g_fw_version, ++ MAX_VERSION_STR_LEN, ++ "%x.%02x", ++ buffer[0], ++ buffer[1] ++ ); ++ ++ g_fw_version[MAX_VERSION_STR_LEN-1] = '\0'; ++ break; ++ case 3: ++ if (n != 2) ++ return -EINVAL; ++ ++ snprintf( ++ g_hw_version, ++ MAX_VERSION_STR_LEN, ++ "%x.%x", ++ buffer[0], ++ buffer[1] ++ ); ++ ++ g_hw_version[MAX_VERSION_STR_LEN-1] = '\0'; ++ break; ++ case 1: ++ if (n >= sizeof(g_serial_num)) ++ return -EINVAL; ++ ++ memcpy(g_serial_num, buffer, sizeof(g_serial_num)); ++ break; ++ case 2: ++ { ++ if (n*2 >= sizeof(g_id)) ++ return -EINVAL; ++ ++ p = g_id; ++ for (j = 0; j < n; ++j) ++ p += sprintf(p, "%02x", buffer[j]); ++ ++ *p = '\0'; ++ } ++ break; ++ default: ++ break; ++ } ++ } ++ ++ return 0; ++} ++ ++static int pisnd_spi_init(struct device *dev) ++{ ++ int ret; ++ struct spi_device *spi; ++ ++ memset(g_serial_num, 0, sizeof(g_serial_num)); ++ memset(g_id, 0, sizeof(g_id)); ++ memset(g_fw_version, 0, sizeof(g_fw_version)); ++ memset(g_hw_version, 0, sizeof(g_hw_version)); ++ ++ spi = pisnd_spi_find_device(); ++ ++ if (spi != NULL) { ++ printd("initializing spi!\n"); ++ pisnd_spi_device = spi; ++ ret = spi_setup(pisnd_spi_device); ++ } else { ++ printe("SPI device not found, deferring!\n"); ++ return -EPROBE_DEFER; ++ } ++ ++ ret = pisnd_spi_gpio_init(dev); ++ ++ if (ret < 0) { ++ printe("SPI GPIO init failed: %d\n", ret); ++ spi_dev_put(pisnd_spi_device); ++ pisnd_spi_device = NULL; ++ pisnd_spi_gpio_uninit(); ++ return ret; ++ } ++ ++ ret = spi_read_info(); ++ ++ if (ret < 0) { ++ printe("Reading card info failed: %d\n", ret); ++ spi_dev_put(pisnd_spi_device); ++ pisnd_spi_device = NULL; ++ pisnd_spi_gpio_uninit(); ++ return ret; ++ } ++ ++ /* Flash the LEDs. */ ++ spi_transfer16(0xf008); ++ ++ ret = pisnd_spi_gpio_irq_init(dev); ++ if (ret < 0) { ++ printe("SPI irq request failed: %d\n", ret); ++ spi_dev_put(pisnd_spi_device); ++ pisnd_spi_device = NULL; ++ pisnd_spi_gpio_irq_uninit(); ++ pisnd_spi_gpio_uninit(); ++ } ++ ++ ret = pisnd_init_workqueues(); ++ if (ret != 0) { ++ printe("Workqueue initialization failed: %d\n", ret); ++ spi_dev_put(pisnd_spi_device); ++ pisnd_spi_device = NULL; ++ pisnd_spi_gpio_irq_uninit(); ++ pisnd_spi_gpio_uninit(); ++ pisnd_uninit_workqueues(); ++ return ret; ++ } ++ ++ if (pisnd_spi_has_more()) { ++ printd("data is available, scheduling from init\n"); ++ pisnd_schedule_process(TASK_PROCESS); ++ } ++ ++ return 0; ++} ++ ++static void pisnd_spi_uninit(void) ++{ ++ pisnd_uninit_workqueues(); ++ ++ spi_dev_put(pisnd_spi_device); ++ pisnd_spi_device = NULL; ++ ++ pisnd_spi_gpio_irq_uninit(); ++ pisnd_spi_gpio_uninit(); ++} ++ ++static void pisnd_spi_flash_leds(uint8_t duration) ++{ ++ g_ledFlashDuration = duration; ++ g_ledFlashDurationChanged = true; ++ printd("schedule from spi_flash_leds\n"); ++ pisnd_schedule_process(TASK_PROCESS); ++} ++ ++static void pisnd_spi_flush(void) ++{ ++ while (!kfifo_is_empty(&spi_fifo_out)) { ++ pisnd_spi_start(); ++ flush_workqueue(pisnd_workqueue); ++ } ++} ++ ++static void pisnd_spi_start(void) ++{ ++ printd("schedule from spi_start\n"); ++ pisnd_schedule_process(TASK_PROCESS); ++} ++ ++static uint8_t pisnd_spi_recv(uint8_t *buffer, uint8_t length) ++{ ++ return kfifo_out(&spi_fifo_in, buffer, length); ++} ++ ++static void pisnd_spi_set_callback(pisnd_spi_recv_cb cb, void *data) ++{ ++ g_recvData = data; ++ g_recvCallback = cb; ++} ++ ++static const char *pisnd_spi_get_serial(void) ++{ ++ return g_serial_num; ++} ++ ++static const char *pisnd_spi_get_id(void) ++{ ++ return g_id; ++} ++ ++static const char *pisnd_spi_get_fw_version(void) ++{ ++ return g_fw_version; ++} ++ ++static const char *pisnd_spi_get_hw_version(void) ++{ ++ return g_hw_version; ++} ++ ++static const struct of_device_id pisound_of_match[] = { ++ { .compatible = "blokaslabs,pisound", }, ++ { .compatible = "blokaslabs,pisound-spi", }, ++ {}, ++}; ++ ++enum { ++ SWITCH = 0, ++ VOLUME = 1, ++}; ++ ++static int pisnd_ctl_info(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_info *uinfo) ++{ ++ if (kcontrol->private_value == SWITCH) { ++ uinfo->type = SNDRV_CTL_ELEM_TYPE_BOOLEAN; ++ uinfo->count = 1; ++ uinfo->value.integer.min = 0; ++ uinfo->value.integer.max = 1; ++ return 0; ++ } else if (kcontrol->private_value == VOLUME) { ++ uinfo->type = SNDRV_CTL_ELEM_TYPE_INTEGER; ++ uinfo->count = 1; ++ uinfo->value.integer.min = 0; ++ uinfo->value.integer.max = 100; ++ return 0; ++ } ++ return -EINVAL; ++} ++ ++static int pisnd_ctl_get(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ if (kcontrol->private_value == SWITCH) { ++ ucontrol->value.integer.value[0] = 1; ++ return 0; ++ } else if (kcontrol->private_value == VOLUME) { ++ ucontrol->value.integer.value[0] = 100; ++ return 0; ++ } ++ ++ return -EINVAL; ++} ++ ++static struct snd_kcontrol_new pisnd_ctl[] = { ++ { ++ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, ++ .name = "PCM Playback Switch", ++ .index = 0, ++ .private_value = SWITCH, ++ .access = SNDRV_CTL_ELEM_ACCESS_READ, ++ .info = pisnd_ctl_info, ++ .get = pisnd_ctl_get, ++ }, ++ { ++ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, ++ .name = "PCM Playback Volume", ++ .index = 0, ++ .private_value = VOLUME, ++ .access = SNDRV_CTL_ELEM_ACCESS_READ, ++ .info = pisnd_ctl_info, ++ .get = pisnd_ctl_get, ++ }, ++}; ++ ++static int pisnd_ctl_init(struct snd_card *card) ++{ ++ int err, i; ++ ++ for (i = 0; i < ARRAY_SIZE(pisnd_ctl); ++i) { ++ err = snd_ctl_add(card, snd_ctl_new1(&pisnd_ctl[i], NULL)); ++ if (err < 0) ++ return err; ++ } ++ ++ return 0; ++} ++ ++static int pisnd_ctl_uninit(void) ++{ ++ return 0; ++} ++ ++static struct gpio_desc *osr0, *osr1, *osr2; ++static struct gpio_desc *reset; ++static struct gpio_desc *button; ++ ++static int pisnd_hw_params( ++ struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params ++ ) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0); ++ ++ /* Pisound runs on fixed 32 clock counts per channel, ++ * as generated by the master ADC. ++ */ ++ snd_soc_dai_set_bclk_ratio(cpu_dai, 32*2); ++ ++ printd("rate = %d\n", params_rate(params)); ++ printd("ch = %d\n", params_channels(params)); ++ printd("bits = %u\n", ++ snd_pcm_format_physical_width(params_format(params))); ++ printd("format = %d\n", params_format(params)); ++ ++ gpiod_set_value(reset, false); ++ ++ switch (params_rate(params)) { ++ case 48000: ++ gpiod_set_value(osr0, true); ++ gpiod_set_value(osr1, false); ++ gpiod_set_value(osr2, false); ++ break; ++ case 96000: ++ gpiod_set_value(osr0, true); ++ gpiod_set_value(osr1, false); ++ gpiod_set_value(osr2, true); ++ break; ++ case 192000: ++ gpiod_set_value(osr0, true); ++ gpiod_set_value(osr1, true); ++ gpiod_set_value(osr2, true); ++ break; ++ default: ++ printe("Unsupported rate %u!\n", params_rate(params)); ++ return -EINVAL; ++ } ++ ++ gpiod_set_value(reset, true); ++ ++ return 0; ++} ++ ++static unsigned int rates[3] = { ++ 48000, 96000, 192000 ++}; ++ ++static struct snd_pcm_hw_constraint_list constraints_rates = { ++ .count = ARRAY_SIZE(rates), ++ .list = rates, ++ .mask = 0, ++}; ++ ++static int pisnd_startup(struct snd_pcm_substream *substream) ++{ ++ int err = snd_pcm_hw_constraint_list( ++ substream->runtime, ++ 0, ++ SNDRV_PCM_HW_PARAM_RATE, ++ &constraints_rates ++ ); ++ ++ if (err < 0) ++ return err; ++ ++ err = snd_pcm_hw_constraint_single( ++ substream->runtime, ++ SNDRV_PCM_HW_PARAM_CHANNELS, ++ 2 ++ ); ++ ++ if (err < 0) ++ return err; ++ ++ err = snd_pcm_hw_constraint_mask64( ++ substream->runtime, ++ SNDRV_PCM_HW_PARAM_FORMAT, ++ SNDRV_PCM_FMTBIT_S16_LE | ++ SNDRV_PCM_FMTBIT_S24_LE | ++ SNDRV_PCM_FMTBIT_S32_LE ++ ); ++ ++ if (err < 0) ++ return err; ++ ++ return 0; ++} ++ ++static struct snd_soc_ops pisnd_ops = { ++ .startup = pisnd_startup, ++ .hw_params = pisnd_hw_params, ++}; ++ ++SND_SOC_DAILINK_DEFS(pisnd, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_DUMMY()), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link pisnd_dai[] = { ++ { ++ .name = "pisound", ++ .stream_name = "pisound", ++ .dai_fmt = ++ SND_SOC_DAIFMT_I2S | ++ SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBM_CFM, ++ .ops = &pisnd_ops, ++ SND_SOC_DAILINK_REG(pisnd), ++ }, ++}; ++ ++static int pisnd_card_probe(struct snd_soc_card *card) ++{ ++ int err = pisnd_midi_init(card->snd_card); ++ ++ if (err < 0) { ++ printe("pisnd_midi_init failed: %d\n", err); ++ return err; ++ } ++ ++ err = pisnd_ctl_init(card->snd_card); ++ if (err < 0) { ++ printe("pisnd_ctl_init failed: %d\n", err); ++ return err; ++ } ++ ++ return 0; ++} ++ ++static int pisnd_card_remove(struct snd_soc_card *card) ++{ ++ pisnd_ctl_uninit(); ++ pisnd_midi_uninit(); ++ return 0; ++} ++ ++static struct snd_soc_card pisnd_card = { ++ .name = "pisound", ++ .owner = THIS_MODULE, ++ .dai_link = pisnd_dai, ++ .num_links = ARRAY_SIZE(pisnd_dai), ++ .probe = pisnd_card_probe, ++ .remove = pisnd_card_remove, ++}; ++ ++static int pisnd_init_gpio(struct device *dev) ++{ ++ osr0 = gpiod_get_index(dev, "osr", 0, GPIOD_ASIS); ++ osr1 = gpiod_get_index(dev, "osr", 1, GPIOD_ASIS); ++ osr2 = gpiod_get_index(dev, "osr", 2, GPIOD_ASIS); ++ ++ reset = gpiod_get_index(dev, "reset", 0, GPIOD_ASIS); ++ ++ button = gpiod_get_index(dev, "button", 0, GPIOD_ASIS); ++ ++ gpiod_direction_output(osr0, 1); ++ gpiod_direction_output(osr1, 1); ++ gpiod_direction_output(osr2, 1); ++ gpiod_direction_output(reset, 1); ++ ++ gpiod_set_value(reset, false); ++ gpiod_set_value(osr0, true); ++ gpiod_set_value(osr1, false); ++ gpiod_set_value(osr2, false); ++ gpiod_set_value(reset, true); ++ ++ gpiod_export(button, false); ++ ++ return 0; ++} ++ ++static int pisnd_uninit_gpio(void) ++{ ++ int i; ++ ++ struct gpio_desc **gpios[] = { ++ &osr0, &osr1, &osr2, &reset, &button, ++ }; ++ ++ gpiod_unexport(button); ++ ++ for (i = 0; i < ARRAY_SIZE(gpios); ++i) { ++ if (*gpios[i] == NULL) { ++ printd("weird, GPIO[%d] is NULL already\n", i); ++ continue; ++ } ++ ++ gpiod_put(*gpios[i]); ++ *gpios[i] = NULL; ++ } ++ ++ return 0; ++} ++ ++static struct kobject *pisnd_kobj; ++ ++static ssize_t pisnd_serial_show( ++ struct kobject *kobj, ++ struct kobj_attribute *attr, ++ char *buf ++ ) ++{ ++ return sprintf(buf, "%s\n", pisnd_spi_get_serial()); ++} ++ ++static ssize_t pisnd_id_show( ++ struct kobject *kobj, ++ struct kobj_attribute *attr, ++ char *buf ++ ) ++{ ++ return sprintf(buf, "%s\n", pisnd_spi_get_id()); ++} ++ ++static ssize_t pisnd_fw_version_show( ++ struct kobject *kobj, ++ struct kobj_attribute *attr, ++ char *buf ++ ) ++{ ++ return sprintf(buf, "%s\n", pisnd_spi_get_fw_version()); ++} ++ ++static ssize_t pisnd_hw_version_show( ++ struct kobject *kobj, ++ struct kobj_attribute *attr, ++ char *buf ++) ++{ ++ return sprintf(buf, "%s\n", pisnd_spi_get_hw_version()); ++} ++ ++static ssize_t pisnd_led_store( ++ struct kobject *kobj, ++ struct kobj_attribute *attr, ++ const char *buf, ++ size_t length ++ ) ++{ ++ uint32_t timeout; ++ int err; ++ ++ err = kstrtou32(buf, 10, &timeout); ++ ++ if (err == 0 && timeout <= 255) ++ pisnd_spi_flash_leds(timeout); ++ ++ return length; ++} ++ ++static struct kobj_attribute pisnd_serial_attribute = ++ __ATTR(serial, 0444, pisnd_serial_show, NULL); ++static struct kobj_attribute pisnd_id_attribute = ++ __ATTR(id, 0444, pisnd_id_show, NULL); ++static struct kobj_attribute pisnd_fw_version_attribute = ++ __ATTR(version, 0444, pisnd_fw_version_show, NULL); ++static struct kobj_attribute pisnd_hw_version_attribute = ++__ATTR(hw_version, 0444, pisnd_hw_version_show, NULL); ++static struct kobj_attribute pisnd_led_attribute = ++ __ATTR(led, 0644, NULL, pisnd_led_store); ++ ++static struct attribute *attrs[] = { ++ &pisnd_serial_attribute.attr, ++ &pisnd_id_attribute.attr, ++ &pisnd_fw_version_attribute.attr, ++ &pisnd_hw_version_attribute.attr, ++ &pisnd_led_attribute.attr, ++ NULL ++}; ++ ++static struct attribute_group attr_group = { .attrs = attrs }; ++ ++static int pisnd_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ int i; ++ ++ ret = pisnd_spi_init(&pdev->dev); ++ if (ret < 0) { ++ printe("pisnd_spi_init failed: %d\n", ret); ++ return ret; ++ } ++ ++ printi("Detected Pisound card:\n"); ++ printi("\tSerial: %s\n", pisnd_spi_get_serial()); ++ printi("\tFirmware Version: %s\n", pisnd_spi_get_fw_version()); ++ printi("\tHardware Version: %s\n", pisnd_spi_get_hw_version()); ++ printi("\tId: %s\n", pisnd_spi_get_id()); ++ ++ pisnd_kobj = kobject_create_and_add("pisound", kernel_kobj); ++ if (!pisnd_kobj) { ++ pisnd_spi_uninit(); ++ return -ENOMEM; ++ } ++ ++ ret = sysfs_create_group(pisnd_kobj, &attr_group); ++ if (ret < 0) { ++ pisnd_spi_uninit(); ++ kobject_put(pisnd_kobj); ++ return -ENOMEM; ++ } ++ ++ pisnd_init_gpio(&pdev->dev); ++ pisnd_card.dev = &pdev->dev; ++ ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ ++ i2s_node = of_parse_phandle( ++ pdev->dev.of_node, ++ "i2s-controller", ++ 0 ++ ); ++ ++ for (i = 0; i < pisnd_card.num_links; ++i) { ++ struct snd_soc_dai_link *dai = &pisnd_dai[i]; ++ ++ if (i2s_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ dai->stream_name = pisnd_spi_get_serial(); ++ } ++ } ++ } ++ ++ ret = snd_soc_register_card(&pisnd_card); ++ ++ if (ret < 0) { ++ if (ret != -EPROBE_DEFER) ++ printe("snd_soc_register_card() failed: %d\n", ret); ++ pisnd_uninit_gpio(); ++ kobject_put(pisnd_kobj); ++ pisnd_spi_uninit(); ++ } ++ ++ return ret; ++} ++ ++static int pisnd_remove(struct platform_device *pdev) ++{ ++ printi("Unloading.\n"); ++ ++ if (pisnd_kobj) { ++ kobject_put(pisnd_kobj); ++ pisnd_kobj = NULL; ++ } ++ ++ pisnd_spi_uninit(); ++ ++ /* Turn off */ ++ gpiod_set_value(reset, false); ++ pisnd_uninit_gpio(); ++ ++ return snd_soc_unregister_card(&pisnd_card); ++} ++ ++MODULE_DEVICE_TABLE(of, pisound_of_match); ++ ++static struct platform_driver pisnd_driver = { ++ .driver = { ++ .name = "snd-rpi-pisound", ++ .owner = THIS_MODULE, ++ .of_match_table = pisound_of_match, ++ }, ++ .probe = pisnd_probe, ++ .remove = pisnd_remove, ++}; ++ ++module_platform_driver(pisnd_driver); ++ ++MODULE_AUTHOR("Giedrius Trainavicius "); ++MODULE_DESCRIPTION("ASoC Driver for Pisound, https://blokas.io/pisound"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/rpi-cirrus.c +@@ -0,0 +1,1025 @@ ++/* ++ * ASoC machine driver for Cirrus Logic Audio Card ++ * (with WM5102 and WM8804 codecs) ++ * ++ * Copyright 2015-2017 Matthias Reichl ++ * ++ * Based on rpi-cirrus-sound-pi driver (c) Wolfson / Cirrus Logic Inc. ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++ ++#include "../codecs/wm5102.h" ++#include "../codecs/wm8804.h" ++ ++#define WM8804_CLKOUT_HZ 12000000 ++ ++#define RPI_CIRRUS_DEFAULT_RATE 44100 ++#define WM5102_MAX_SYSCLK_1 49152000 /* max sysclk for 4K family */ ++#define WM5102_MAX_SYSCLK_2 45158400 /* max sysclk for 11.025K family */ ++ ++static inline unsigned int calc_sysclk(unsigned int rate) ++{ ++ return (rate % 4000) ? WM5102_MAX_SYSCLK_2 : WM5102_MAX_SYSCLK_1; ++} ++ ++enum { ++ DAI_WM5102 = 0, ++ DAI_WM8804, ++}; ++ ++struct rpi_cirrus_priv { ++ /* mutex for synchronzing FLL1 access with DAPM */ ++ struct mutex lock; ++ unsigned int card_rate; ++ int sync_path_enable; ++ int fll1_freq; /* negative means RefClock in spdif rx case */ ++ ++ /* track hw params/free for substreams */ ++ unsigned int params_set; ++ unsigned int min_rate_idx, max_rate_idx; ++ unsigned char iec958_status[4]; ++}; ++ ++/* helper functions */ ++static inline struct snd_soc_pcm_runtime *get_wm5102_runtime( ++ struct snd_soc_card *card) { ++ return snd_soc_get_pcm_runtime(card, &card->dai_link[DAI_WM5102]); ++} ++ ++static inline struct snd_soc_pcm_runtime *get_wm8804_runtime( ++ struct snd_soc_card *card) { ++ return snd_soc_get_pcm_runtime(card, &card->dai_link[DAI_WM8804]); ++} ++ ++ ++struct rate_info { ++ unsigned int value; ++ char *text; ++}; ++ ++static struct rate_info min_rates[] = { ++ { 0, "off"}, ++ { 32000, "32kHz"}, ++ { 44100, "44.1kHz"} ++}; ++ ++#define NUM_MIN_RATES ARRAY_SIZE(min_rates) ++ ++static int rpi_cirrus_min_rate_info(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_info *uinfo) ++{ ++ uinfo->type = SNDRV_CTL_ELEM_TYPE_ENUMERATED; ++ uinfo->count = 1; ++ uinfo->value.enumerated.items = NUM_MIN_RATES; ++ ++ if (uinfo->value.enumerated.item >= NUM_MIN_RATES) ++ uinfo->value.enumerated.item = NUM_MIN_RATES - 1; ++ strcpy(uinfo->value.enumerated.name, ++ min_rates[uinfo->value.enumerated.item].text); ++ return 0; ++} ++ ++static int rpi_cirrus_min_rate_get(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ ++ ucontrol->value.enumerated.item[0] = priv->min_rate_idx; ++ return 0; ++} ++ ++static int rpi_cirrus_min_rate_put(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ int changed = 0; ++ ++ if (priv->min_rate_idx != ucontrol->value.enumerated.item[0]) { ++ changed = 1; ++ priv->min_rate_idx = ucontrol->value.enumerated.item[0]; ++ } ++ ++ return changed; ++} ++ ++static struct rate_info max_rates[] = { ++ { 0, "off"}, ++ { 48000, "48kHz"}, ++ { 96000, "96kHz"} ++}; ++ ++#define NUM_MAX_RATES ARRAY_SIZE(max_rates) ++ ++static int rpi_cirrus_max_rate_info(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_info *uinfo) ++{ ++ uinfo->type = SNDRV_CTL_ELEM_TYPE_ENUMERATED; ++ uinfo->count = 1; ++ uinfo->value.enumerated.items = NUM_MAX_RATES; ++ if (uinfo->value.enumerated.item >= NUM_MAX_RATES) ++ uinfo->value.enumerated.item = NUM_MAX_RATES - 1; ++ strcpy(uinfo->value.enumerated.name, ++ max_rates[uinfo->value.enumerated.item].text); ++ return 0; ++} ++ ++static int rpi_cirrus_max_rate_get(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ ++ ucontrol->value.enumerated.item[0] = priv->max_rate_idx; ++ return 0; ++} ++ ++static int rpi_cirrus_max_rate_put(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ int changed = 0; ++ ++ if (priv->max_rate_idx != ucontrol->value.enumerated.item[0]) { ++ changed = 1; ++ priv->max_rate_idx = ucontrol->value.enumerated.item[0]; ++ } ++ ++ return changed; ++} ++ ++static int rpi_cirrus_spdif_info(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_info *uinfo) ++{ ++ uinfo->type = SNDRV_CTL_ELEM_TYPE_IEC958; ++ uinfo->count = 1; ++ return 0; ++} ++ ++static int rpi_cirrus_spdif_playback_get(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ int i; ++ ++ for (i = 0; i < 4; i++) ++ ucontrol->value.iec958.status[i] = priv->iec958_status[i]; ++ ++ return 0; ++} ++ ++static int rpi_cirrus_spdif_playback_put(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct snd_soc_component *wm8804_component = ++ asoc_rtd_to_codec(get_wm8804_runtime(card), 0)->component; ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ unsigned char *stat = priv->iec958_status; ++ unsigned char *ctrl_stat = ucontrol->value.iec958.status; ++ unsigned int mask; ++ int i, changed = 0; ++ ++ for (i = 0; i < 4; i++) { ++ mask = (i == 3) ? 0x3f : 0xff; ++ if ((ctrl_stat[i] & mask) != (stat[i] & mask)) { ++ changed = 1; ++ stat[i] = ctrl_stat[i] & mask; ++ snd_soc_component_update_bits(wm8804_component, ++ WM8804_SPDTX1 + i, mask, stat[i]); ++ } ++ } ++ ++ return changed; ++} ++ ++static int rpi_cirrus_spdif_mask_get(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ ucontrol->value.iec958.status[0] = 0xff; ++ ucontrol->value.iec958.status[1] = 0xff; ++ ucontrol->value.iec958.status[2] = 0xff; ++ ucontrol->value.iec958.status[3] = 0x3f; ++ ++ return 0; ++} ++ ++static int rpi_cirrus_spdif_capture_get(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct snd_soc_component *wm8804_component = ++ asoc_rtd_to_codec(get_wm8804_runtime(card), 0)->component; ++ unsigned int val, mask; ++ int i; ++ ++ for (i = 0; i < 4; i++) { ++ val = snd_soc_component_read(wm8804_component, ++ WM8804_RXCHAN1 + i); ++ mask = (i == 3) ? 0x3f : 0xff; ++ ucontrol->value.iec958.status[i] = val & mask; ++ } ++ ++ return 0; ++} ++ ++#define SPDIF_FLAG_CTRL(desc, reg, bit, invert) \ ++{ \ ++ .access = SNDRV_CTL_ELEM_ACCESS_READ \ ++ | SNDRV_CTL_ELEM_ACCESS_VOLATILE, \ ++ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, \ ++ .name = SNDRV_CTL_NAME_IEC958("", CAPTURE, NONE) \ ++ desc " Flag", \ ++ .info = snd_ctl_boolean_mono_info, \ ++ .get = rpi_cirrus_spdif_status_flag_get, \ ++ .private_value = \ ++ (bit) | ((reg) << 8) | ((invert) << 16) \ ++} ++ ++static int rpi_cirrus_spdif_status_flag_get(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct snd_soc_component *wm8804_component = ++ asoc_rtd_to_codec(get_wm8804_runtime(card), 0)->component; ++ ++ unsigned int bit = kcontrol->private_value & 0xff; ++ unsigned int reg = (kcontrol->private_value >> 8) & 0xff; ++ unsigned int invert = (kcontrol->private_value >> 16) & 0xff; ++ unsigned int val; ++ bool flag; ++ ++ val = snd_soc_component_read(wm8804_component, reg); ++ ++ flag = val & (1 << bit); ++ ++ ucontrol->value.integer.value[0] = invert ? !flag : flag; ++ ++ return 0; ++} ++ ++static const char * const recovered_frequency_texts[] = { ++ "176.4/192 kHz", ++ "88.2/96 kHz", ++ "44.1/48 kHz", ++ "32 kHz" ++}; ++ ++#define NUM_RECOVERED_FREQUENCIES \ ++ ARRAY_SIZE(recovered_frequency_texts) ++ ++static int rpi_cirrus_recovered_frequency_info(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_info *uinfo) ++{ ++ uinfo->type = SNDRV_CTL_ELEM_TYPE_ENUMERATED; ++ uinfo->count = 1; ++ uinfo->value.enumerated.items = NUM_RECOVERED_FREQUENCIES; ++ if (uinfo->value.enumerated.item >= NUM_RECOVERED_FREQUENCIES) ++ uinfo->value.enumerated.item = NUM_RECOVERED_FREQUENCIES - 1; ++ strcpy(uinfo->value.enumerated.name, ++ recovered_frequency_texts[uinfo->value.enumerated.item]); ++ return 0; ++} ++ ++static int rpi_cirrus_recovered_frequency_get(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_card *card = snd_kcontrol_chip(kcontrol); ++ struct snd_soc_component *wm8804_component = ++ asoc_rtd_to_codec(get_wm8804_runtime(card), 0)->component; ++ unsigned int val; ++ ++ val = snd_soc_component_read(wm8804_component, WM8804_SPDSTAT); ++ ++ ucontrol->value.enumerated.item[0] = (val >> 4) & 0x03; ++ return 0; ++} ++ ++static const struct snd_kcontrol_new rpi_cirrus_controls[] = { ++ { ++ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, ++ .name = "Min Sample Rate", ++ .info = rpi_cirrus_min_rate_info, ++ .get = rpi_cirrus_min_rate_get, ++ .put = rpi_cirrus_min_rate_put, ++ }, ++ { ++ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, ++ .name = "Max Sample Rate", ++ .info = rpi_cirrus_max_rate_info, ++ .get = rpi_cirrus_max_rate_get, ++ .put = rpi_cirrus_max_rate_put, ++ }, ++ { ++ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, ++ .name = SNDRV_CTL_NAME_IEC958("", PLAYBACK, DEFAULT), ++ .info = rpi_cirrus_spdif_info, ++ .get = rpi_cirrus_spdif_playback_get, ++ .put = rpi_cirrus_spdif_playback_put, ++ }, ++ { ++ .access = SNDRV_CTL_ELEM_ACCESS_READ ++ | SNDRV_CTL_ELEM_ACCESS_VOLATILE, ++ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, ++ .name = SNDRV_CTL_NAME_IEC958("", CAPTURE, DEFAULT), ++ .info = rpi_cirrus_spdif_info, ++ .get = rpi_cirrus_spdif_capture_get, ++ }, ++ { ++ .access = SNDRV_CTL_ELEM_ACCESS_READ, ++ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, ++ .name = SNDRV_CTL_NAME_IEC958("", PLAYBACK, MASK), ++ .info = rpi_cirrus_spdif_info, ++ .get = rpi_cirrus_spdif_mask_get, ++ }, ++ { ++ .access = SNDRV_CTL_ELEM_ACCESS_READ ++ | SNDRV_CTL_ELEM_ACCESS_VOLATILE, ++ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, ++ .name = SNDRV_CTL_NAME_IEC958("", CAPTURE, NONE) ++ "Recovered Frequency", ++ .info = rpi_cirrus_recovered_frequency_info, ++ .get = rpi_cirrus_recovered_frequency_get, ++ }, ++ SPDIF_FLAG_CTRL("Audio", WM8804_SPDSTAT, 0, 1), ++ SPDIF_FLAG_CTRL("Non-PCM", WM8804_SPDSTAT, 1, 0), ++ SPDIF_FLAG_CTRL("Copyright", WM8804_SPDSTAT, 2, 1), ++ SPDIF_FLAG_CTRL("De-Emphasis", WM8804_SPDSTAT, 3, 0), ++ SPDIF_FLAG_CTRL("Lock", WM8804_SPDSTAT, 6, 1), ++ SPDIF_FLAG_CTRL("Invalid", WM8804_INTSTAT, 1, 0), ++ SPDIF_FLAG_CTRL("TransErr", WM8804_INTSTAT, 3, 0), ++}; ++ ++static const char * const linein_micbias_texts[] = { ++ "off", "on", ++}; ++ ++static SOC_ENUM_SINGLE_VIRT_DECL(linein_micbias_enum, ++ linein_micbias_texts); ++ ++static const struct snd_kcontrol_new linein_micbias_mux = ++ SOC_DAPM_ENUM("Route", linein_micbias_enum); ++ ++static int rpi_cirrus_spdif_rx_enable_event(struct snd_soc_dapm_widget *w, ++ struct snd_kcontrol *kcontrol, int event); ++ ++const struct snd_soc_dapm_widget rpi_cirrus_dapm_widgets[] = { ++ SND_SOC_DAPM_MIC("DMIC", NULL), ++ SND_SOC_DAPM_MIC("Headset Mic", NULL), ++ SND_SOC_DAPM_INPUT("Line Input"), ++ SND_SOC_DAPM_MIC("Line Input with Micbias", NULL), ++ SND_SOC_DAPM_MUX("Line Input Micbias", SND_SOC_NOPM, 0, 0, ++ &linein_micbias_mux), ++ SND_SOC_DAPM_INPUT("dummy SPDIF in"), ++ SND_SOC_DAPM_PGA_E("dummy SPDIFRX", SND_SOC_NOPM, 0, 0, NULL, 0, ++ rpi_cirrus_spdif_rx_enable_event, ++ SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_POST_PMD), ++ SND_SOC_DAPM_INPUT("Dummy Input"), ++ SND_SOC_DAPM_OUTPUT("Dummy Output"), ++}; ++ ++const struct snd_soc_dapm_route rpi_cirrus_dapm_routes[] = { ++ { "IN1L", NULL, "Headset Mic" }, ++ { "IN1R", NULL, "Headset Mic" }, ++ { "Headset Mic", NULL, "MICBIAS1" }, ++ ++ { "IN2L", NULL, "DMIC" }, ++ { "IN2R", NULL, "DMIC" }, ++ { "DMIC", NULL, "MICBIAS2" }, ++ ++ { "IN3L", NULL, "Line Input Micbias" }, ++ { "IN3R", NULL, "Line Input Micbias" }, ++ ++ { "Line Input Micbias", "off", "Line Input" }, ++ { "Line Input Micbias", "on", "Line Input with Micbias" }, ++ ++ /* Make sure MICVDD is enabled, otherwise we get noise */ ++ { "Line Input", NULL, "MICVDD" }, ++ { "Line Input with Micbias", NULL, "MICBIAS3" }, ++ ++ /* Dummy routes to check whether SPDIF RX is enabled or not */ ++ {"dummy SPDIFRX", NULL, "dummy SPDIF in"}, ++ {"AIFTX", NULL, "dummy SPDIFRX"}, ++ ++ /* ++ * Dummy routes to keep wm5102 from staying off on ++ * playback/capture if all mixers are off. ++ */ ++ { "Dummy Output", NULL, "AIF1RX1" }, ++ { "Dummy Output", NULL, "AIF1RX2" }, ++ { "AIF1TX1", NULL, "Dummy Input" }, ++ { "AIF1TX2", NULL, "Dummy Input" }, ++}; ++ ++static int rpi_cirrus_clear_flls(struct snd_soc_card *card, ++ struct snd_soc_component *wm5102_component) { ++ ++ int ret1, ret2; ++ ++ ret1 = snd_soc_component_set_pll(wm5102_component, ++ WM5102_FLL1, ARIZONA_FLL_SRC_NONE, 0, 0); ++ ret2 = snd_soc_component_set_pll(wm5102_component, ++ WM5102_FLL1_REFCLK, ARIZONA_FLL_SRC_NONE, 0, 0); ++ ++ if (ret1) { ++ dev_warn(card->dev, ++ "setting FLL1 to zero failed: %d\n", ret1); ++ return ret1; ++ } ++ if (ret2) { ++ dev_warn(card->dev, ++ "setting FLL1_REFCLK to zero failed: %d\n", ret2); ++ return ret2; ++ } ++ return 0; ++} ++ ++static int rpi_cirrus_set_fll(struct snd_soc_card *card, ++ struct snd_soc_component *wm5102_component, unsigned int clk_freq) ++{ ++ int ret = snd_soc_component_set_pll(wm5102_component, ++ WM5102_FLL1, ++ ARIZONA_CLK_SRC_MCLK1, ++ WM8804_CLKOUT_HZ, ++ clk_freq); ++ if (ret) ++ dev_err(card->dev, "Failed to set FLL1 to %d: %d\n", ++ clk_freq, ret); ++ ++ usleep_range(1000, 2000); ++ return ret; ++} ++ ++static int rpi_cirrus_set_fll_refclk(struct snd_soc_card *card, ++ struct snd_soc_component *wm5102_component, ++ unsigned int clk_freq, unsigned int aif2_freq) ++{ ++ int ret = snd_soc_component_set_pll(wm5102_component, ++ WM5102_FLL1_REFCLK, ++ ARIZONA_CLK_SRC_MCLK1, ++ WM8804_CLKOUT_HZ, ++ clk_freq); ++ if (ret) { ++ dev_err(card->dev, ++ "Failed to set FLL1_REFCLK to %d: %d\n", ++ clk_freq, ret); ++ return ret; ++ } ++ ++ ret = snd_soc_component_set_pll(wm5102_component, ++ WM5102_FLL1, ++ ARIZONA_CLK_SRC_AIF2BCLK, ++ aif2_freq, clk_freq); ++ if (ret) ++ dev_err(card->dev, ++ "Failed to set FLL1 with Sync Clock %d to %d: %d\n", ++ aif2_freq, clk_freq, ret); ++ ++ usleep_range(1000, 2000); ++ return ret; ++} ++ ++static int rpi_cirrus_spdif_rx_enable_event(struct snd_soc_dapm_widget *w, ++ struct snd_kcontrol *kcontrol, int event) ++{ ++ struct snd_soc_card *card = w->dapm->card; ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ struct snd_soc_component *wm5102_component = ++ asoc_rtd_to_codec(get_wm5102_runtime(card), 0)->component; ++ ++ unsigned int clk_freq, aif2_freq; ++ int ret = 0; ++ ++ switch (event) { ++ case SND_SOC_DAPM_POST_PMU: ++ mutex_lock(&priv->lock); ++ ++ /* Enable sync path in case of SPDIF capture use case */ ++ ++ clk_freq = calc_sysclk(priv->card_rate); ++ aif2_freq = 64 * priv->card_rate; ++ ++ dev_dbg(card->dev, ++ "spdif_rx: changing FLL1 to use Ref Clock clk: %d spdif: %d\n", ++ clk_freq, aif2_freq); ++ ++ ret = rpi_cirrus_clear_flls(card, wm5102_component); ++ if (ret) { ++ dev_err(card->dev, "spdif_rx: failed to clear FLLs\n"); ++ goto out; ++ } ++ ++ ret = rpi_cirrus_set_fll_refclk(card, wm5102_component, ++ clk_freq, aif2_freq); ++ ++ if (ret) { ++ dev_err(card->dev, "spdif_rx: failed to set FLLs\n"); ++ goto out; ++ } ++ ++ /* set to negative to indicate we're doing spdif rx */ ++ priv->fll1_freq = -clk_freq; ++ priv->sync_path_enable = 1; ++ break; ++ ++ case SND_SOC_DAPM_POST_PMD: ++ mutex_lock(&priv->lock); ++ priv->sync_path_enable = 0; ++ break; ++ ++ default: ++ return 0; ++ } ++ ++out: ++ mutex_unlock(&priv->lock); ++ return ret; ++} ++ ++static int rpi_cirrus_set_bias_level(struct snd_soc_card *card, ++ struct snd_soc_dapm_context *dapm, ++ enum snd_soc_bias_level level) ++{ ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ struct snd_soc_pcm_runtime *wm5102_runtime = get_wm5102_runtime(card); ++ struct snd_soc_component *wm5102_component = ++ asoc_rtd_to_codec(wm5102_runtime, 0)->component; ++ ++ int ret = 0; ++ unsigned int clk_freq; ++ ++ if (dapm->dev != asoc_rtd_to_codec(wm5102_runtime, 0)->dev) ++ return 0; ++ ++ switch (level) { ++ case SND_SOC_BIAS_PREPARE: ++ if (dapm->bias_level == SND_SOC_BIAS_ON) ++ break; ++ ++ mutex_lock(&priv->lock); ++ ++ if (!priv->sync_path_enable) { ++ clk_freq = calc_sysclk(priv->card_rate); ++ ++ dev_dbg(card->dev, ++ "set_bias: changing FLL1 from %d to %d\n", ++ priv->fll1_freq, clk_freq); ++ ++ ret = rpi_cirrus_set_fll(card, ++ wm5102_component, clk_freq); ++ if (ret) ++ dev_err(card->dev, ++ "set_bias: Failed to set FLL1\n"); ++ else ++ priv->fll1_freq = clk_freq; ++ } ++ mutex_unlock(&priv->lock); ++ break; ++ default: ++ break; ++ } ++ ++ return ret; ++} ++ ++static int rpi_cirrus_set_bias_level_post(struct snd_soc_card *card, ++ struct snd_soc_dapm_context *dapm, ++ enum snd_soc_bias_level level) ++{ ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ struct snd_soc_pcm_runtime *wm5102_runtime = get_wm5102_runtime(card); ++ struct snd_soc_component *wm5102_component = ++ asoc_rtd_to_codec(wm5102_runtime, 0)->component; ++ ++ if (dapm->dev != asoc_rtd_to_codec(wm5102_runtime, 0)->dev) ++ return 0; ++ ++ switch (level) { ++ case SND_SOC_BIAS_STANDBY: ++ mutex_lock(&priv->lock); ++ ++ dev_dbg(card->dev, ++ "set_bias_post: changing FLL1 from %d to off\n", ++ priv->fll1_freq); ++ ++ if (rpi_cirrus_clear_flls(card, wm5102_component)) ++ dev_err(card->dev, ++ "set_bias_post: failed to clear FLLs\n"); ++ else ++ priv->fll1_freq = 0; ++ ++ mutex_unlock(&priv->lock); ++ ++ break; ++ default: ++ break; ++ } ++ ++ return 0; ++} ++ ++static int rpi_cirrus_set_wm8804_pll(struct snd_soc_card *card, ++ struct snd_soc_dai *wm8804_dai, unsigned int rate) ++{ ++ int ret; ++ ++ /* use 256fs */ ++ unsigned int clk_freq = rate * 256; ++ ++ ret = snd_soc_dai_set_pll(wm8804_dai, 0, 0, ++ WM8804_CLKOUT_HZ, clk_freq); ++ if (ret) { ++ dev_err(card->dev, ++ "Failed to set WM8804 PLL to %d: %d\n", clk_freq, ret); ++ return ret; ++ } ++ ++ /* Set MCLK as PLL Output */ ++ ret = snd_soc_dai_set_sysclk(wm8804_dai, ++ WM8804_TX_CLKSRC_PLL, clk_freq, 0); ++ if (ret) { ++ dev_err(card->dev, ++ "Failed to set MCLK as PLL Output: %d\n", ret); ++ return ret; ++ } ++ ++ return ret; ++} ++ ++static int rpi_cirrus_startup(struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_card *card = rtd->card; ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ unsigned int min_rate = min_rates[priv->min_rate_idx].value; ++ unsigned int max_rate = max_rates[priv->max_rate_idx].value; ++ ++ if (min_rate || max_rate) { ++ if (max_rate == 0) ++ max_rate = UINT_MAX; ++ ++ dev_dbg(card->dev, ++ "startup: limiting rate to %u-%u\n", ++ min_rate, max_rate); ++ ++ snd_pcm_hw_constraint_minmax(substream->runtime, ++ SNDRV_PCM_HW_PARAM_RATE, min_rate, max_rate); ++ } ++ ++ return 0; ++} ++ ++static struct snd_soc_pcm_stream rpi_cirrus_dai_link2_params = { ++ .formats = SNDRV_PCM_FMTBIT_S24_LE, ++ .channels_min = 2, ++ .channels_max = 2, ++ .rate_min = RPI_CIRRUS_DEFAULT_RATE, ++ .rate_max = RPI_CIRRUS_DEFAULT_RATE, ++}; ++ ++static int rpi_cirrus_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_card *card = rtd->card; ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ struct snd_soc_dai *bcm_i2s_dai = asoc_rtd_to_cpu(rtd, 0); ++ struct snd_soc_component *wm5102_component = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_dai *wm8804_dai = asoc_rtd_to_codec(get_wm8804_runtime(card), 0); ++ ++ int ret; ++ ++ unsigned int width = snd_pcm_format_physical_width( ++ params_format(params)); ++ unsigned int rate = params_rate(params); ++ unsigned int clk_freq = calc_sysclk(rate); ++ ++ mutex_lock(&priv->lock); ++ ++ dev_dbg(card->dev, "hw_params: setting rate to %d\n", rate); ++ ++ ret = snd_soc_dai_set_bclk_ratio(bcm_i2s_dai, 2 * width); ++ if (ret) { ++ dev_err(card->dev, "set_bclk_ratio failed: %d\n", ret); ++ goto out; ++ } ++ ++ ret = snd_soc_dai_set_tdm_slot(asoc_rtd_to_codec(rtd, 0), 0x03, 0x03, 2, width); ++ if (ret) { ++ dev_err(card->dev, "set_tdm_slot failed: %d\n", ret); ++ goto out; ++ } ++ ++ /* WM8804 supports sample rates from 32k only */ ++ if (rate >= 32000) { ++ ret = rpi_cirrus_set_wm8804_pll(card, wm8804_dai, rate); ++ if (ret) ++ goto out; ++ } ++ ++ ret = snd_soc_component_set_sysclk(wm5102_component, ++ ARIZONA_CLK_SYSCLK, ++ ARIZONA_CLK_SRC_FLL1, ++ clk_freq, ++ SND_SOC_CLOCK_IN); ++ if (ret) { ++ dev_err(card->dev, "Failed to set SYSCLK: %d\n", ret); ++ goto out; ++ } ++ ++ if ((priv->fll1_freq > 0) && (priv->fll1_freq != clk_freq)) { ++ dev_dbg(card->dev, ++ "hw_params: changing FLL1 from %d to %d\n", ++ priv->fll1_freq, clk_freq); ++ ++ if (rpi_cirrus_clear_flls(card, wm5102_component)) { ++ dev_err(card->dev, "hw_params: failed to clear FLLs\n"); ++ goto out; ++ } ++ ++ if (rpi_cirrus_set_fll(card, wm5102_component, clk_freq)) { ++ dev_err(card->dev, "hw_params: failed to set FLL\n"); ++ goto out; ++ } ++ ++ priv->fll1_freq = clk_freq; ++ } ++ ++ priv->card_rate = rate; ++ rpi_cirrus_dai_link2_params.rate_min = rate; ++ rpi_cirrus_dai_link2_params.rate_max = rate; ++ ++ priv->params_set |= 1 << substream->stream; ++ ++out: ++ mutex_unlock(&priv->lock); ++ ++ return ret; ++} ++ ++static int rpi_cirrus_hw_free(struct snd_pcm_substream *substream) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_card *card = rtd->card; ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ struct snd_soc_component *wm5102_component = asoc_rtd_to_codec(rtd, 0)->component; ++ int ret; ++ unsigned int old_params_set = priv->params_set; ++ ++ priv->params_set &= ~(1 << substream->stream); ++ ++ /* disable sysclk if this was the last open stream */ ++ if (priv->params_set == 0 && old_params_set) { ++ dev_dbg(card->dev, ++ "hw_free: Setting SYSCLK to Zero\n"); ++ ++ ret = snd_soc_component_set_sysclk(wm5102_component, ++ ARIZONA_CLK_SYSCLK, ++ ARIZONA_CLK_SRC_FLL1, ++ 0, ++ SND_SOC_CLOCK_IN); ++ if (ret) ++ dev_err(card->dev, ++ "hw_free: Failed to set SYSCLK to Zero: %d\n", ++ ret); ++ } ++ return 0; ++} ++ ++static int rpi_cirrus_init_wm5102(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ int ret; ++ ++ /* no 32kHz input, derive it from sysclk if needed */ ++ snd_soc_component_update_bits(component, ++ ARIZONA_CLOCK_32K_1, ARIZONA_CLK_32K_SRC_MASK, 2); ++ ++ if (rpi_cirrus_clear_flls(rtd->card, component)) ++ dev_warn(rtd->card->dev, ++ "init_wm5102: failed to clear FLLs\n"); ++ ++ ret = snd_soc_component_set_sysclk(component, ++ ARIZONA_CLK_SYSCLK, ARIZONA_CLK_SRC_FLL1, ++ 0, SND_SOC_CLOCK_IN); ++ if (ret) { ++ dev_err(rtd->card->dev, ++ "Failed to set SYSCLK to Zero: %d\n", ret); ++ return ret; ++ } ++ ++ return 0; ++} ++ ++static int rpi_cirrus_init_wm8804(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_soc_dai *codec_dai = asoc_rtd_to_codec(rtd, 0); ++ struct snd_soc_component *component = codec_dai->component; ++ struct snd_soc_card *card = rtd->card; ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ unsigned int val, mask; ++ int i, ret; ++ ++ for (i = 0; i < 4; i++) { ++ val = snd_soc_component_read(component, ++ WM8804_SPDTX1 + i); ++ mask = (i == 3) ? 0x3f : 0xff; ++ priv->iec958_status[i] = val & mask; ++ } ++ ++ /* Setup for 256fs */ ++ ret = snd_soc_dai_set_clkdiv(codec_dai, ++ WM8804_MCLK_DIV, WM8804_MCLKDIV_256FS); ++ if (ret) { ++ dev_err(card->dev, ++ "init_wm8804: Failed to set MCLK_DIV to 256fs: %d\n", ++ ret); ++ return ret; ++ } ++ ++ /* Output OSC on CLKOUT */ ++ ret = snd_soc_dai_set_sysclk(codec_dai, ++ WM8804_CLKOUT_SRC_OSCCLK, WM8804_CLKOUT_HZ, 0); ++ if (ret) ++ dev_err(card->dev, ++ "init_wm8804: Failed to set CLKOUT as OSC Frequency: %d\n", ++ ret); ++ ++ /* Init PLL with default samplerate */ ++ ret = rpi_cirrus_set_wm8804_pll(card, codec_dai, ++ RPI_CIRRUS_DEFAULT_RATE); ++ if (ret) ++ dev_err(card->dev, ++ "init_wm8804: Failed to setup PLL for %dHz: %d\n", ++ RPI_CIRRUS_DEFAULT_RATE, ret); ++ ++ return ret; ++} ++ ++static struct snd_soc_ops rpi_cirrus_ops = { ++ .startup = rpi_cirrus_startup, ++ .hw_params = rpi_cirrus_hw_params, ++ .hw_free = rpi_cirrus_hw_free, ++}; ++ ++SND_SOC_DAILINK_DEFS(wm5102, ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_CODEC("wm5102-codec", "wm5102-aif1")), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++SND_SOC_DAILINK_DEFS(wm8804, ++ DAILINK_COMP_ARRAY(COMP_CPU("wm5102-aif2")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("wm8804.1-003b", "wm8804-spdif"))); ++ ++static struct snd_soc_dai_link rpi_cirrus_dai[] = { ++ [DAI_WM5102] = { ++ .name = "WM5102", ++ .stream_name = "WM5102 AiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S ++ | SND_SOC_DAIFMT_NB_NF ++ | SND_SOC_DAIFMT_CBM_CFM, ++ .ops = &rpi_cirrus_ops, ++ .init = rpi_cirrus_init_wm5102, ++ SND_SOC_DAILINK_REG(wm5102), ++ }, ++ [DAI_WM8804] = { ++ .name = "WM5102 SPDIF", ++ .stream_name = "SPDIF Tx/Rx", ++ .dai_fmt = SND_SOC_DAIFMT_I2S ++ | SND_SOC_DAIFMT_NB_NF ++ | SND_SOC_DAIFMT_CBM_CFM, ++ .ignore_suspend = 1, ++ .params = &rpi_cirrus_dai_link2_params, ++ .init = rpi_cirrus_init_wm8804, ++ SND_SOC_DAILINK_REG(wm8804), ++ }, ++}; ++ ++ ++static int rpi_cirrus_late_probe(struct snd_soc_card *card) ++{ ++ struct rpi_cirrus_priv *priv = snd_soc_card_get_drvdata(card); ++ struct snd_soc_pcm_runtime *wm5102_runtime = get_wm5102_runtime(card); ++ struct snd_soc_pcm_runtime *wm8804_runtime = get_wm8804_runtime(card); ++ int ret; ++ ++ dev_dbg(card->dev, "iec958_bits: %02x %02x %02x %02x\n", ++ priv->iec958_status[0], ++ priv->iec958_status[1], ++ priv->iec958_status[2], ++ priv->iec958_status[3]); ++ ++ ret = snd_soc_dai_set_sysclk( ++ asoc_rtd_to_codec(wm5102_runtime, 0), ARIZONA_CLK_SYSCLK, 0, 0); ++ if (ret) { ++ dev_err(card->dev, ++ "Failed to set WM5102 codec dai clk domain: %d\n", ret); ++ return ret; ++ } ++ ++ ret = snd_soc_dai_set_sysclk( ++ asoc_rtd_to_cpu(wm8804_runtime, 0), ARIZONA_CLK_SYSCLK, 0, 0); ++ if (ret) ++ dev_err(card->dev, ++ "Failed to set WM8804 codec dai clk domain: %d\n", ret); ++ ++ return ret; ++} ++ ++/* audio machine driver */ ++static struct snd_soc_card rpi_cirrus_card = { ++ .name = "RPi-Cirrus", ++ .driver_name = "RPiCirrus", ++ .owner = THIS_MODULE, ++ .dai_link = rpi_cirrus_dai, ++ .num_links = ARRAY_SIZE(rpi_cirrus_dai), ++ .late_probe = rpi_cirrus_late_probe, ++ .controls = rpi_cirrus_controls, ++ .num_controls = ARRAY_SIZE(rpi_cirrus_controls), ++ .dapm_widgets = rpi_cirrus_dapm_widgets, ++ .num_dapm_widgets = ARRAY_SIZE(rpi_cirrus_dapm_widgets), ++ .dapm_routes = rpi_cirrus_dapm_routes, ++ .num_dapm_routes = ARRAY_SIZE(rpi_cirrus_dapm_routes), ++ .set_bias_level = rpi_cirrus_set_bias_level, ++ .set_bias_level_post = rpi_cirrus_set_bias_level_post, ++}; ++ ++static int rpi_cirrus_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ struct rpi_cirrus_priv *priv; ++ struct device_node *i2s_node; ++ ++ priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); ++ if (!priv) ++ return -ENOMEM; ++ ++ priv->min_rate_idx = 1; /* min samplerate 32kHz */ ++ priv->card_rate = RPI_CIRRUS_DEFAULT_RATE; ++ ++ mutex_init(&priv->lock); ++ ++ snd_soc_card_set_drvdata(&rpi_cirrus_card, priv); ++ ++ if (!pdev->dev.of_node) ++ return -ENODEV; ++ ++ i2s_node = of_parse_phandle( ++ pdev->dev.of_node, "i2s-controller", 0); ++ if (!i2s_node) { ++ dev_err(&pdev->dev, "i2s-controller missing in DT\n"); ++ return -ENODEV; ++ } ++ ++ rpi_cirrus_dai[DAI_WM5102].cpus->of_node = i2s_node; ++ rpi_cirrus_dai[DAI_WM5102].platforms->of_node = i2s_node; ++ ++ rpi_cirrus_card.dev = &pdev->dev; ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, &rpi_cirrus_card); ++ if (ret) { ++ if (ret == -EPROBE_DEFER) ++ dev_dbg(&pdev->dev, ++ "register card requested probe deferral\n"); ++ else ++ dev_err(&pdev->dev, ++ "Failed to register card: %d\n", ret); ++ } ++ ++ return ret; ++} ++ ++static const struct of_device_id rpi_cirrus_of_match[] = { ++ { .compatible = "wlf,rpi-cirrus", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, rpi_cirrus_of_match); ++ ++static struct platform_driver rpi_cirrus_driver = { ++ .driver = { ++ .name = "snd-rpi-cirrus", ++ .of_match_table = of_match_ptr(rpi_cirrus_of_match), ++ }, ++ .probe = rpi_cirrus_probe, ++}; ++ ++module_platform_driver(rpi_cirrus_driver); ++ ++MODULE_AUTHOR("Matthias Reichl "); ++MODULE_DESCRIPTION("ASoC driver for Cirrus Logic Audio Card"); ++MODULE_LICENSE("GPL"); +--- /dev/null ++++ b/sound/soc/bcm/rpi-proto.c +@@ -0,0 +1,147 @@ ++/* ++ * ASoC driver for PROTO AudioCODEC (with a WM8731) ++ * connected to a Raspberry Pi ++ * ++ * Author: Florian Meier, ++ * Copyright 2013 ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++ ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++#include "../codecs/wm8731.h" ++ ++static const unsigned int wm8731_rates_12288000[] = { ++ 8000, 32000, 48000, 96000, ++}; ++ ++static struct snd_pcm_hw_constraint_list wm8731_constraints_12288000 = { ++ .list = wm8731_rates_12288000, ++ .count = ARRAY_SIZE(wm8731_rates_12288000), ++}; ++ ++static int snd_rpi_proto_startup(struct snd_pcm_substream *substream) ++{ ++ /* Setup constraints, because there is a 12.288 MHz XTAL on the board */ ++ snd_pcm_hw_constraint_list(substream->runtime, 0, ++ SNDRV_PCM_HW_PARAM_RATE, ++ &wm8731_constraints_12288000); ++ return 0; ++} ++ ++static int snd_rpi_proto_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_dai *codec_dai = asoc_rtd_to_codec(rtd, 0); ++ struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0); ++ int sysclk = 12288000; /* This is fixed on this board */ ++ ++ /* Set proto bclk */ ++ int ret = snd_soc_dai_set_bclk_ratio(cpu_dai,32*2); ++ if (ret < 0){ ++ dev_err(rtd->card->dev, ++ "Failed to set BCLK ratio %d\n", ret); ++ return ret; ++ } ++ ++ /* Set proto sysclk */ ++ ret = snd_soc_dai_set_sysclk(codec_dai, WM8731_SYSCLK_XTAL, ++ sysclk, SND_SOC_CLOCK_IN); ++ if (ret < 0) { ++ dev_err(rtd->card->dev, ++ "Failed to set WM8731 SYSCLK: %d\n", ret); ++ return ret; ++ } ++ ++ return 0; ++} ++ ++/* machine stream operations */ ++static struct snd_soc_ops snd_rpi_proto_ops = { ++ .startup = snd_rpi_proto_startup, ++ .hw_params = snd_rpi_proto_hw_params, ++}; ++ ++SND_SOC_DAILINK_DEFS(rpi_proto, ++ DAILINK_COMP_ARRAY(COMP_CPU("bcm2708-i2s.0")), ++ DAILINK_COMP_ARRAY(COMP_CODEC("wm8731.1-001a", "wm8731-hifi")), ++ DAILINK_COMP_ARRAY(COMP_PLATFORM("bcm2708-i2s.0"))); ++ ++static struct snd_soc_dai_link snd_rpi_proto_dai[] = { ++{ ++ .name = "WM8731", ++ .stream_name = "WM8731 HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S ++ | SND_SOC_DAIFMT_NB_NF ++ | SND_SOC_DAIFMT_CBM_CFM, ++ .ops = &snd_rpi_proto_ops, ++ SND_SOC_DAILINK_REG(rpi_proto), ++}, ++}; ++ ++/* audio machine driver */ ++static struct snd_soc_card snd_rpi_proto = { ++ .name = "snd_rpi_proto", ++ .owner = THIS_MODULE, ++ .dai_link = snd_rpi_proto_dai, ++ .num_links = ARRAY_SIZE(snd_rpi_proto_dai), ++}; ++ ++static int snd_rpi_proto_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ ++ snd_rpi_proto.dev = &pdev->dev; ++ ++ if (pdev->dev.of_node) { ++ struct device_node *i2s_node; ++ struct snd_soc_dai_link *dai = &snd_rpi_proto_dai[0]; ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ ++ if (i2s_node) { ++ dai->cpus->dai_name = NULL; ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->name = NULL; ++ dai->platforms->of_node = i2s_node; ++ } ++ } ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, &snd_rpi_proto); ++ if (ret && ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, ++ "snd_soc_register_card() failed: %d\n", ret); ++ ++ return ret; ++} ++ ++static const struct of_device_id snd_rpi_proto_of_match[] = { ++ { .compatible = "rpi,rpi-proto", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, snd_rpi_proto_of_match); ++ ++static struct platform_driver snd_rpi_proto_driver = { ++ .driver = { ++ .name = "snd-rpi-proto", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_rpi_proto_of_match, ++ }, ++ .probe = snd_rpi_proto_probe, ++}; ++ ++module_platform_driver(snd_rpi_proto_driver); ++ ++MODULE_AUTHOR("Florian Meier"); ++MODULE_DESCRIPTION("ASoC Driver for Raspberry Pi connected to PROTO board (WM8731)"); ++MODULE_LICENSE("GPL"); +--- /dev/null ++++ b/sound/soc/bcm/rpi-simple-soundcard.c +@@ -0,0 +1,339 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * rpi-simple-soundcard.c -- ALSA SoC Raspberry Pi soundcard. ++ * ++ * Copyright (C) 2018 Raspberry Pi. ++ * ++ * Authors: Tim Gover ++ * ++ * Based on code: ++ * hifiberry_amp.c, hifiberry_dac.c, rpi-dac.c ++ * by Florian Meier ++ * ++ * googlevoicehat-soundcard.c ++ * by Peter Malkin ++ * ++ * adau1977-adc.c ++ * by Andrey Grodzovsky ++ * ++ * merus-amp.c ++ * by Ariel Muszkat ++ * Jorgen Kragh Jakobsen ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++/* Parameters for generic RPI functions */ ++struct snd_rpi_simple_drvdata { ++ struct snd_soc_dai_link *dai; ++ const char* card_name; ++ unsigned int fixed_bclk_ratio; ++}; ++ ++static int snd_rpi_simple_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ struct snd_rpi_simple_drvdata *drvdata = ++ snd_soc_card_get_drvdata(rtd->card); ++ struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0); ++ ++ if (drvdata->fixed_bclk_ratio > 0) ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, ++ drvdata->fixed_bclk_ratio); ++ ++ return 0; ++} ++ ++static int snd_rpi_simple_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0); ++ struct snd_rpi_simple_drvdata *drvdata; ++ unsigned int sample_bits; ++ ++ drvdata = snd_soc_card_get_drvdata(rtd->card); ++ ++ if (drvdata->fixed_bclk_ratio > 0) ++ return 0; // BCLK is configured in .init ++ ++ /* The simple drivers just set the bclk_ratio to sample_bits * 2 so ++ * hard-code this for now. More complex drivers could just replace ++ * the hw_params routine. ++ */ ++ sample_bits = snd_pcm_format_physical_width(params_format(params)); ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, sample_bits * 2); ++} ++ ++static struct snd_soc_ops snd_rpi_simple_ops = { ++ .hw_params = snd_rpi_simple_hw_params, ++}; ++ ++enum adau1977_clk_id { ++ ADAU1977_SYSCLK, ++}; ++ ++enum adau1977_sysclk_src { ++ ADAU1977_SYSCLK_SRC_MCLK, ++ ADAU1977_SYSCLK_SRC_LRCLK, ++}; ++ ++static int adau1977_init(struct snd_soc_pcm_runtime *rtd) ++{ ++ int ret; ++ struct snd_soc_dai *codec_dai = asoc_rtd_to_codec(rtd, 0); ++ ++ ret = snd_soc_dai_set_tdm_slot(codec_dai, 0, 0, 0, 0); ++ if (ret < 0) ++ return ret; ++ ++ return snd_soc_component_set_sysclk(codec_dai->component, ++ ADAU1977_SYSCLK, ADAU1977_SYSCLK_SRC_MCLK, ++ 11289600, SND_SOC_CLOCK_IN); ++} ++ ++SND_SOC_DAILINK_DEFS(adau1977, ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_CODEC("adau1977.1-0011", "adau1977-hifi")), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++static struct snd_soc_dai_link snd_rpi_adau1977_dai[] = { ++ { ++ .name = "adau1977", ++ .stream_name = "ADAU1977", ++ .init = adau1977_init, ++ .dai_fmt = SND_SOC_DAIFMT_I2S | ++ SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBM_CFM, ++ SND_SOC_DAILINK_REG(adau1977), ++ }, ++}; ++ ++static struct snd_rpi_simple_drvdata drvdata_adau1977 = { ++ .card_name = "snd_rpi_adau1977_adc", ++ .dai = snd_rpi_adau1977_dai, ++}; ++ ++SND_SOC_DAILINK_DEFS(gvchat, ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_CODEC("voicehat-codec", "voicehat-hifi")), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++static struct snd_soc_dai_link snd_googlevoicehat_soundcard_dai[] = { ++{ ++ .name = "Google voiceHAT SoundCard", ++ .stream_name = "Google voiceHAT SoundCard HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ SND_SOC_DAILINK_REG(gvchat), ++}, ++}; ++ ++static struct snd_rpi_simple_drvdata drvdata_googlevoicehat = { ++ .card_name = "snd_rpi_googlevoicehat_soundcard", ++ .dai = snd_googlevoicehat_soundcard_dai, ++}; ++ ++SND_SOC_DAILINK_DEFS(hifiberry_dacplusdsp, ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_CODEC("dacplusdsp-codec", "dacplusdsp-hifi")), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++static struct snd_soc_dai_link snd_hifiberrydacplusdsp_soundcard_dai[] = { ++{ ++ .name = "Hifiberry DAC+DSP SoundCard", ++ .stream_name = "Hifiberry DAC+DSP SoundCard HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | ++ SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ SND_SOC_DAILINK_REG(hifiberry_dacplusdsp), ++}, ++}; ++ ++static struct snd_rpi_simple_drvdata drvdata_hifiberrydacplusdsp = { ++ .card_name = "snd_rpi_hifiberrydacplusdsp_soundcard", ++ .dai = snd_hifiberrydacplusdsp_soundcard_dai, ++}; ++ ++SND_SOC_DAILINK_DEFS(hifiberry_amp, ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_CODEC("tas5713.1-001b", "tas5713-hifi")), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++static struct snd_soc_dai_link snd_hifiberry_amp_dai[] = { ++ { ++ .name = "HifiBerry AMP", ++ .stream_name = "HifiBerry AMP HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | ++ SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ SND_SOC_DAILINK_REG(hifiberry_amp), ++ }, ++}; ++ ++static struct snd_rpi_simple_drvdata drvdata_hifiberry_amp = { ++ .card_name = "snd_rpi_hifiberry_amp", ++ .dai = snd_hifiberry_amp_dai, ++ .fixed_bclk_ratio = 64, ++}; ++ ++SND_SOC_DAILINK_DEFS(hifiberry_dac, ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_CODEC("pcm5102a-codec", "pcm5102a-hifi")), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++static struct snd_soc_dai_link snd_hifiberry_dac_dai[] = { ++ { ++ .name = "HifiBerry DAC", ++ .stream_name = "HifiBerry DAC HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | ++ SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ SND_SOC_DAILINK_REG(hifiberry_dac), ++ }, ++}; ++ ++static struct snd_rpi_simple_drvdata drvdata_hifiberry_dac = { ++ .card_name = "snd_rpi_hifiberry_dac", ++ .dai = snd_hifiberry_dac_dai, ++}; ++ ++SND_SOC_DAILINK_DEFS(rpi_dac, ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_CODEC("pcm1794a-codec", "pcm1794a-hifi")), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++static struct snd_soc_dai_link snd_rpi_dac_dai[] = { ++{ ++ .name = "RPi-DAC", ++ .stream_name = "RPi-DAC HiFi", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ SND_SOC_DAILINK_REG(rpi_dac), ++}, ++}; ++ ++static struct snd_rpi_simple_drvdata drvdata_rpi_dac = { ++ .card_name = "snd_rpi_rpi_dac", ++ .dai = snd_rpi_dac_dai, ++ .fixed_bclk_ratio = 64, ++}; ++ ++SND_SOC_DAILINK_DEFS(merus_amp, ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_CODEC("ma120x0p.1-0020","ma120x0p-amp")), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++static struct snd_soc_dai_link snd_merus_amp_dai[] = { ++ { ++ .name = "MerusAmp", ++ .stream_name = "Merus Audio Amp", ++ .dai_fmt = SND_SOC_DAIFMT_I2S | ++ SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBS_CFS, ++ SND_SOC_DAILINK_REG(merus_amp), ++ }, ++}; ++ ++static struct snd_rpi_simple_drvdata drvdata_merus_amp = { ++ .card_name = "snd_rpi_merus_amp", ++ .dai = snd_merus_amp_dai, ++ .fixed_bclk_ratio = 64, ++}; ++ ++static const struct of_device_id snd_rpi_simple_of_match[] = { ++ { .compatible = "adi,adau1977-adc", ++ .data = (void *) &drvdata_adau1977 }, ++ { .compatible = "googlevoicehat,googlevoicehat-soundcard", ++ .data = (void *) &drvdata_googlevoicehat }, ++ { .compatible = "hifiberrydacplusdsp,hifiberrydacplusdsp-soundcard", ++ .data = (void *) &drvdata_hifiberrydacplusdsp }, ++ { .compatible = "hifiberry,hifiberry-amp", ++ .data = (void *) &drvdata_hifiberry_amp }, ++ { .compatible = "hifiberry,hifiberry-dac", ++ .data = (void *) &drvdata_hifiberry_dac }, ++ { .compatible = "rpi,rpi-dac", &drvdata_rpi_dac}, ++ { .compatible = "merus,merus-amp", ++ .data = (void *) &drvdata_merus_amp }, ++ {}, ++}; ++ ++static struct snd_soc_card snd_rpi_simple = { ++ .driver_name = "RPi-simple", ++ .owner = THIS_MODULE, ++ .dai_link = NULL, ++ .num_links = 1, /* Only a single DAI supported at the moment */ ++}; ++ ++static int snd_rpi_simple_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ const struct of_device_id *of_id; ++ ++ snd_rpi_simple.dev = &pdev->dev; ++ of_id = of_match_node(snd_rpi_simple_of_match, pdev->dev.of_node); ++ ++ if (pdev->dev.of_node && of_id->data) { ++ struct device_node *i2s_node; ++ struct snd_rpi_simple_drvdata *drvdata = ++ (struct snd_rpi_simple_drvdata *) of_id->data; ++ struct snd_soc_dai_link *dai = drvdata->dai; ++ ++ snd_soc_card_set_drvdata(&snd_rpi_simple, drvdata); ++ ++ /* More complex drivers might override individual functions */ ++ if (!dai->init) ++ dai->init = snd_rpi_simple_init; ++ if (!dai->ops) ++ dai->ops = &snd_rpi_simple_ops; ++ ++ snd_rpi_simple.name = drvdata->card_name; ++ ++ snd_rpi_simple.dai_link = dai; ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ if (!i2s_node) { ++ pr_err("Failed to find i2s-controller DT node\n"); ++ return -ENODEV; ++ } ++ ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->of_node = i2s_node; ++ } ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, &snd_rpi_simple); ++ if (ret && ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, "Failed to register card %d\n", ret); ++ ++ return ret; ++} ++ ++static struct platform_driver snd_rpi_simple_driver = { ++ .driver = { ++ .name = "snd-rpi-simple", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_rpi_simple_of_match, ++ }, ++ .probe = snd_rpi_simple_probe, ++}; ++MODULE_DEVICE_TABLE(of, snd_rpi_simple_of_match); ++ ++module_platform_driver(snd_rpi_simple_driver); ++ ++MODULE_AUTHOR("Tim Gover "); ++MODULE_DESCRIPTION("ASoC Raspberry Pi simple soundcard driver "); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/bcm/rpi-wm8804-soundcard.c +@@ -0,0 +1,410 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * rpi--wm8804.c -- ALSA SoC Raspberry Pi soundcard. ++ * ++ * Copyright (C) 2018 Raspberry Pi. ++ * ++ * Authors: Tim Gover ++ * ++ * Generic driver for Pi Hat WM8804 digi sounds cards ++ * ++ * Based upon code from: ++ * justboom-digi.c ++ * by Milan Neskovic ++ * ++ * iqaudio_digi.c ++ * by Daniel Matuschek ++ * ++ * allo-digione.c ++ * by Baswaraj ++ * ++ * hifiberry-digi.c ++ * Daniel Matuschek ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++#include "../codecs/wm8804.h" ++ ++struct wm8804_clk_cfg { ++ unsigned int sysclk_freq; ++ unsigned int mclk_freq; ++ unsigned int mclk_div; ++}; ++ ++/* Parameters for generic functions */ ++struct snd_rpi_wm8804_drvdata { ++ /* Required - pointer to the DAI structure */ ++ struct snd_soc_dai_link *dai; ++ /* Required - snd_soc_card name */ ++ const char *card_name; ++ /* Optional DT node names if card info is defined in DT */ ++ const char *card_name_dt; ++ const char *dai_name_dt; ++ const char *dai_stream_name_dt; ++ /* Optional probe extension - called prior to register_card */ ++ int (*probe)(struct platform_device *pdev); ++}; ++ ++static struct gpio_desc *snd_clk44gpio; ++static struct gpio_desc *snd_clk48gpio; ++static int wm8804_samplerate = 0; ++ ++/* Forward declarations */ ++static struct snd_soc_dai_link snd_allo_digione_dai[]; ++static struct snd_soc_card snd_rpi_wm8804; ++ ++ ++#define CLK_44EN_RATE 22579200UL ++#define CLK_48EN_RATE 24576000UL ++ ++static unsigned int snd_rpi_wm8804_enable_clock(unsigned int samplerate) ++{ ++ switch (samplerate) { ++ case 11025: ++ case 22050: ++ case 44100: ++ case 88200: ++ case 176400: ++ gpiod_set_value_cansleep(snd_clk44gpio, 1); ++ gpiod_set_value_cansleep(snd_clk48gpio, 0); ++ return CLK_44EN_RATE; ++ default: ++ gpiod_set_value_cansleep(snd_clk48gpio, 1); ++ gpiod_set_value_cansleep(snd_clk44gpio, 0); ++ return CLK_48EN_RATE; ++ } ++} ++ ++static void snd_rpi_wm8804_clk_cfg(unsigned int samplerate, ++ struct wm8804_clk_cfg *clk_cfg) ++{ ++ clk_cfg->sysclk_freq = 27000000; ++ ++ if (samplerate <= 96000 || ++ snd_rpi_wm8804.dai_link == snd_allo_digione_dai) { ++ clk_cfg->mclk_freq = samplerate * 256; ++ clk_cfg->mclk_div = WM8804_MCLKDIV_256FS; ++ } else { ++ clk_cfg->mclk_freq = samplerate * 128; ++ clk_cfg->mclk_div = WM8804_MCLKDIV_128FS; ++ } ++ ++ if (!(IS_ERR(snd_clk44gpio) || IS_ERR(snd_clk48gpio))) ++ clk_cfg->sysclk_freq = snd_rpi_wm8804_enable_clock(samplerate); ++} ++ ++static int snd_rpi_wm8804_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params) ++{ ++ struct snd_soc_pcm_runtime *rtd = substream->private_data; ++ struct snd_soc_dai *codec_dai = asoc_rtd_to_codec(rtd, 0); ++ struct snd_soc_component *component = asoc_rtd_to_codec(rtd, 0)->component; ++ struct snd_soc_dai *cpu_dai = asoc_rtd_to_cpu(rtd, 0); ++ int sampling_freq = 1; ++ int ret; ++ struct wm8804_clk_cfg clk_cfg; ++ int samplerate = params_rate(params); ++ ++ if (samplerate == wm8804_samplerate) ++ return 0; ++ ++ /* clear until all clocks are setup properly */ ++ wm8804_samplerate = 0; ++ ++ snd_rpi_wm8804_clk_cfg(samplerate, &clk_cfg); ++ ++ pr_debug("%s samplerate: %d mclk_freq: %u mclk_div: %u sysclk: %u\n", ++ __func__, samplerate, clk_cfg.mclk_freq, ++ clk_cfg.mclk_div, clk_cfg.sysclk_freq); ++ ++ switch (samplerate) { ++ case 32000: ++ sampling_freq = 0x03; ++ break; ++ case 44100: ++ sampling_freq = 0x00; ++ break; ++ case 48000: ++ sampling_freq = 0x02; ++ break; ++ case 88200: ++ sampling_freq = 0x08; ++ break; ++ case 96000: ++ sampling_freq = 0x0a; ++ break; ++ case 176400: ++ sampling_freq = 0x0c; ++ break; ++ case 192000: ++ sampling_freq = 0x0e; ++ break; ++ default: ++ dev_err(rtd->card->dev, ++ "Failed to set WM8804 SYSCLK, unsupported samplerate %d\n", ++ samplerate); ++ } ++ ++ snd_soc_dai_set_clkdiv(codec_dai, WM8804_MCLK_DIV, clk_cfg.mclk_div); ++ snd_soc_dai_set_pll(codec_dai, 0, 0, ++ clk_cfg.sysclk_freq, clk_cfg.mclk_freq); ++ ++ ret = snd_soc_dai_set_sysclk(codec_dai, WM8804_TX_CLKSRC_PLL, ++ clk_cfg.sysclk_freq, SND_SOC_CLOCK_OUT); ++ if (ret < 0) { ++ dev_err(rtd->card->dev, ++ "Failed to set WM8804 SYSCLK: %d\n", ret); ++ return ret; ++ } ++ ++ wm8804_samplerate = samplerate; ++ ++ /* set sampling frequency status bits */ ++ snd_soc_component_update_bits(component, WM8804_SPDTX4, 0x0f, ++ sampling_freq); ++ ++ return snd_soc_dai_set_bclk_ratio(cpu_dai, 64); ++} ++ ++static struct snd_soc_ops snd_rpi_wm8804_ops = { ++ .hw_params = snd_rpi_wm8804_hw_params, ++}; ++ ++SND_SOC_DAILINK_DEFS(justboom_digi, ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++static struct snd_soc_dai_link snd_justboom_digi_dai[] = { ++{ ++ .name = "JustBoom Digi", ++ .stream_name = "JustBoom Digi HiFi", ++ SND_SOC_DAILINK_REG(justboom_digi), ++}, ++}; ++ ++static struct snd_rpi_wm8804_drvdata drvdata_justboom_digi = { ++ .card_name = "snd_rpi_justboom_digi", ++ .dai = snd_justboom_digi_dai, ++}; ++ ++SND_SOC_DAILINK_DEFS(iqaudio_digi, ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++static struct snd_soc_dai_link snd_iqaudio_digi_dai[] = { ++{ ++ .name = "IQAudIO Digi", ++ .stream_name = "IQAudIO Digi HiFi", ++ SND_SOC_DAILINK_REG(iqaudio_digi), ++}, ++}; ++ ++static struct snd_rpi_wm8804_drvdata drvdata_iqaudio_digi = { ++ .card_name = "IQAudIODigi", ++ .dai = snd_iqaudio_digi_dai, ++ .card_name_dt = "wm8804-digi,card-name", ++ .dai_name_dt = "wm8804-digi,dai-name", ++ .dai_stream_name_dt = "wm8804-digi,dai-stream-name", ++}; ++ ++static int snd_allo_digione_probe(struct platform_device *pdev) ++{ ++ pr_debug("%s\n", __func__); ++ ++ if (IS_ERR(snd_clk44gpio) || IS_ERR(snd_clk48gpio)) { ++ dev_err(&pdev->dev, "devm_gpiod_get() failed\n"); ++ return -EINVAL; ++ } ++ return 0; ++} ++ ++SND_SOC_DAILINK_DEFS(allo_digione, ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++static struct snd_soc_dai_link snd_allo_digione_dai[] = { ++{ ++ .name = "Allo DigiOne", ++ .stream_name = "Allo DigiOne HiFi", ++ SND_SOC_DAILINK_REG(allo_digione), ++}, ++}; ++ ++static struct snd_rpi_wm8804_drvdata drvdata_allo_digione = { ++ .card_name = "snd_allo_digione", ++ .dai = snd_allo_digione_dai, ++ .probe = snd_allo_digione_probe, ++}; ++ ++SND_SOC_DAILINK_DEFS(hifiberry_digi, ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_EMPTY()), ++ DAILINK_COMP_ARRAY(COMP_EMPTY())); ++ ++static struct snd_soc_dai_link snd_hifiberry_digi_dai[] = { ++{ ++ .name = "HifiBerry Digi", ++ .stream_name = "HifiBerry Digi HiFi", ++ SND_SOC_DAILINK_REG(hifiberry_digi), ++}, ++}; ++ ++static int snd_hifiberry_digi_probe(struct platform_device *pdev) ++{ ++ pr_debug("%s\n", __func__); ++ ++ if (IS_ERR(snd_clk44gpio) || IS_ERR(snd_clk48gpio)) ++ return 0; ++ ++ snd_hifiberry_digi_dai->name = "HiFiBerry Digi+ Pro"; ++ snd_hifiberry_digi_dai->stream_name = "HiFiBerry Digi+ Pro HiFi"; ++ return 0; ++} ++ ++static struct snd_rpi_wm8804_drvdata drvdata_hifiberry_digi = { ++ .card_name = "snd_rpi_hifiberry_digi", ++ .dai = snd_hifiberry_digi_dai, ++ .probe = snd_hifiberry_digi_probe, ++}; ++ ++static const struct of_device_id snd_rpi_wm8804_of_match[] = { ++ { .compatible = "justboom,justboom-digi", ++ .data = (void *) &drvdata_justboom_digi }, ++ { .compatible = "iqaudio,wm8804-digi", ++ .data = (void *) &drvdata_iqaudio_digi }, ++ { .compatible = "allo,allo-digione", ++ .data = (void *) &drvdata_allo_digione }, ++ { .compatible = "hifiberry,hifiberry-digi", ++ .data = (void *) &drvdata_hifiberry_digi }, ++ {}, ++}; ++ ++static struct snd_soc_card snd_rpi_wm8804 = { ++ .driver_name = "RPi-WM8804", ++ .owner = THIS_MODULE, ++ .dai_link = NULL, ++ .num_links = 1, ++}; ++ ++static int snd_rpi_wm8804_probe(struct platform_device *pdev) ++{ ++ int ret = 0; ++ const struct of_device_id *of_id; ++ ++ snd_rpi_wm8804.dev = &pdev->dev; ++ of_id = of_match_node(snd_rpi_wm8804_of_match, pdev->dev.of_node); ++ ++ if (pdev->dev.of_node && of_id->data) { ++ struct device_node *i2s_node; ++ struct snd_rpi_wm8804_drvdata *drvdata = ++ (struct snd_rpi_wm8804_drvdata *) of_id->data; ++ struct snd_soc_dai_link *dai = drvdata->dai; ++ ++ snd_soc_card_set_drvdata(&snd_rpi_wm8804, drvdata); ++ ++ if (!dai->ops) ++ dai->ops = &snd_rpi_wm8804_ops; ++ if (!dai->codecs->dai_name) ++ dai->codecs->dai_name = "wm8804-spdif"; ++ if (!dai->codecs->name) ++ dai->codecs->name = "wm8804.1-003b"; ++ if (!dai->dai_fmt) ++ dai->dai_fmt = SND_SOC_DAIFMT_I2S | ++ SND_SOC_DAIFMT_NB_NF | ++ SND_SOC_DAIFMT_CBM_CFM; ++ ++ snd_rpi_wm8804.dai_link = dai; ++ i2s_node = of_parse_phandle(pdev->dev.of_node, ++ "i2s-controller", 0); ++ if (!i2s_node) { ++ pr_err("Failed to find i2s-controller DT node\n"); ++ return -ENODEV; ++ } ++ ++ snd_rpi_wm8804.name = drvdata->card_name; ++ ++ /* If requested by in drvdata get card & DAI names from DT */ ++ if (drvdata->card_name_dt) ++ of_property_read_string(i2s_node, ++ drvdata->card_name_dt, ++ &snd_rpi_wm8804.name); ++ ++ if (drvdata->dai_name_dt) ++ of_property_read_string(i2s_node, ++ drvdata->dai_name_dt, ++ &dai->name); ++ ++ if (drvdata->dai_stream_name_dt) ++ of_property_read_string(i2s_node, ++ drvdata->dai_stream_name_dt, ++ &dai->stream_name); ++ ++ dai->cpus->of_node = i2s_node; ++ dai->platforms->of_node = i2s_node; ++ ++ /* ++ * clk44gpio and clk48gpio are not required by all cards so ++ * don't check the error status. ++ */ ++ snd_clk44gpio = ++ devm_gpiod_get(&pdev->dev, "clock44", GPIOD_OUT_LOW); ++ ++ snd_clk48gpio = ++ devm_gpiod_get(&pdev->dev, "clock48", GPIOD_OUT_LOW); ++ ++ if (drvdata->probe) { ++ ret = drvdata->probe(pdev); ++ if (ret < 0) { ++ dev_err(&pdev->dev, "Custom probe failed %d\n", ++ ret); ++ return ret; ++ } ++ } ++ ++ pr_debug("%s card: %s dai: %s stream: %s\n", __func__, ++ snd_rpi_wm8804.name, ++ dai->name, dai->stream_name); ++ } ++ ++ ret = devm_snd_soc_register_card(&pdev->dev, &snd_rpi_wm8804); ++ if (ret && ret != -EPROBE_DEFER) ++ dev_err(&pdev->dev, "Failed to register card %d\n", ret); ++ ++ return ret; ++} ++ ++static struct platform_driver snd_rpi_wm8804_driver = { ++ .driver = { ++ .name = "snd-rpi-wm8804", ++ .owner = THIS_MODULE, ++ .of_match_table = snd_rpi_wm8804_of_match, ++ }, ++ .probe = snd_rpi_wm8804_probe, ++}; ++MODULE_DEVICE_TABLE(of, snd_rpi_wm8804_of_match); ++ ++module_platform_driver(snd_rpi_wm8804_driver); ++ ++MODULE_AUTHOR("Tim Gover "); ++MODULE_DESCRIPTION("ASoC Raspberry Pi Hat generic digi driver for WM8804 based cards"); ++MODULE_LICENSE("GPL v2"); +--- a/sound/soc/codecs/Kconfig ++++ b/sound/soc/codecs/Kconfig +@@ -100,12 +100,14 @@ config SND_SOC_ALL_CODECS + imply SND_SOC_ICS43432 + imply SND_SOC_INNO_RK3036 + imply SND_SOC_ISABELLE ++ imply SND_SOC_I_SABRE_CODEC + imply SND_SOC_JZ4740_CODEC + imply SND_SOC_JZ4725B_CODEC + imply SND_SOC_JZ4770_CODEC + imply SND_SOC_LM4857 + imply SND_SOC_LM49453 + imply SND_SOC_LOCHNAGAR_SC ++ imply SND_SOC_MA120X0P + imply SND_SOC_MAX98088 + imply SND_SOC_MAX98090 + imply SND_SOC_MAX98095 +@@ -142,6 +144,7 @@ config SND_SOC_ALL_CODECS + imply SND_SOC_PCM179X_SPI + imply SND_SOC_PCM186X_I2C + imply SND_SOC_PCM186X_SPI ++ imply SND_SOC_PCM1794A + imply SND_SOC_PCM3008 + imply SND_SOC_PCM3060_I2C + imply SND_SOC_PCM3060_SPI +@@ -206,6 +209,7 @@ config SND_SOC_ALL_CODECS + imply SND_SOC_TLV320ADCX140 + imply SND_SOC_TLV320AIC23_I2C + imply SND_SOC_TLV320AIC23_SPI ++ imply SND_SOC_TAS5713 + imply SND_SOC_TLV320AIC26 + imply SND_SOC_TLV320AIC31XX + imply SND_SOC_TLV320AIC32X4_I2C +@@ -343,12 +347,12 @@ config SND_SOC_AD193X + tristate + + config SND_SOC_AD193X_SPI +- tristate ++ tristate "Analog Devices AU193X CODEC - SPI" + depends on SPI_MASTER + select SND_SOC_AD193X + + config SND_SOC_AD193X_I2C +- tristate ++ tristate "Analog Devices AU193X CODEC - I2C" + depends on I2C + select SND_SOC_AD193X + +@@ -804,7 +808,7 @@ config SND_SOC_HDAC_HDA + select SND_HDA + + config SND_SOC_ICS43432 +- tristate ++ tristate "InvenSense ICS43432 I2S microphone codec" + + config SND_SOC_INNO_RK3036 + tristate "Inno codec driver for RK3036 SoC" +@@ -825,6 +829,13 @@ config SND_SOC_LOCHNAGAR_SC + This driver support the sound card functionality of the Cirrus + Logic Lochnagar audio development board. + ++config SND_SOC_MA120X0P ++ tristate "Infineon Merus(TM) MA120X0P Multilevel Class-D Audio amplifiers" ++ depends on I2C ++ help ++ Enable support for Infineon MA120X0P Multilevel Class-D audio power ++ amplifiers. ++ + config SND_SOC_MADERA + tristate + default y if SND_SOC_CS47L15=y +@@ -1125,6 +1136,10 @@ config SND_SOC_RT5616 + tristate "Realtek RT5616 CODEC" + depends on I2C + ++config SND_SOC_PCM1794A ++ tristate ++ depends on I2C ++ + config SND_SOC_RT5631 + tristate "Realtek ALC5631/RT5631 CODEC" + depends on I2C +@@ -1346,6 +1361,9 @@ config SND_SOC_TFA9879 + tristate "NXP Semiconductors TFA9879 amplifier" + depends on I2C + ++config SND_SOC_TAS5713 ++ tristate ++ + config SND_SOC_TLV320AIC23 + tristate + +@@ -1784,4 +1802,8 @@ config SND_SOC_TPA6130A2 + tristate "Texas Instruments TPA6130A2 headphone amplifier" + depends on I2C + ++config SND_SOC_I_SABRE_CODEC ++ tristate "Audiophonics I-SABRE Codec" ++ depends on I2C ++ + endmenu +--- a/sound/soc/codecs/Makefile ++++ b/sound/soc/codecs/Makefile +@@ -96,6 +96,7 @@ snd-soc-hdac-hda-objs := hdac_hda.o + snd-soc-ics43432-objs := ics43432.o + snd-soc-inno-rk3036-objs := inno_rk3036.o + snd-soc-isabelle-objs := isabelle.o ++snd-soc-i-sabre-codec-objs := i-sabre-codec.o + snd-soc-jz4740-codec-objs := jz4740.o + snd-soc-jz4725b-codec-objs := jz4725b.o + snd-soc-jz4770-codec-objs := jz4770.o +@@ -103,6 +104,7 @@ snd-soc-l3-objs := l3.o + snd-soc-lm4857-objs := lm4857.o + snd-soc-lm49453-objs := lm49453.o + snd-soc-lochnagar-sc-objs := lochnagar-sc.o ++snd-soc-ma120x0p-objs := ma120x0p.o + snd-soc-madera-objs := madera.o + snd-soc-max9759-objs := max9759.o + snd-soc-max9768-objs := max9768.o +@@ -144,6 +146,7 @@ snd-soc-pcm179x-spi-objs := pcm179x-spi. + snd-soc-pcm186x-objs := pcm186x.o + snd-soc-pcm186x-i2c-objs := pcm186x-i2c.o + snd-soc-pcm186x-spi-objs := pcm186x-spi.o ++snd-soc-pcm1794a-objs := pcm1794a.o + snd-soc-pcm3008-objs := pcm3008.o + snd-soc-pcm3060-objs := pcm3060.o + snd-soc-pcm3060-i2c-objs := pcm3060-i2c.o +@@ -216,6 +219,7 @@ snd-soc-tas6424-objs := tas6424.o + snd-soc-tda7419-objs := tda7419.o + snd-soc-tas2770-objs := tas2770.o + snd-soc-tfa9879-objs := tfa9879.o ++snd-soc-tas5713-objs := tas5713.o + snd-soc-tlv320aic23-objs := tlv320aic23.o + snd-soc-tlv320aic23-i2c-objs := tlv320aic23-i2c.o + snd-soc-tlv320aic23-spi-objs := tlv320aic23-spi.o +@@ -405,6 +409,7 @@ obj-$(CONFIG_SND_SOC_HDAC_HDA) += snd-so + obj-$(CONFIG_SND_SOC_ICS43432) += snd-soc-ics43432.o + obj-$(CONFIG_SND_SOC_INNO_RK3036) += snd-soc-inno-rk3036.o + obj-$(CONFIG_SND_SOC_ISABELLE) += snd-soc-isabelle.o ++obj-$(CONFIG_SND_SOC_I_SABRE_CODEC) += snd-soc-i-sabre-codec.o + obj-$(CONFIG_SND_SOC_JZ4740_CODEC) += snd-soc-jz4740-codec.o + obj-$(CONFIG_SND_SOC_JZ4725B_CODEC) += snd-soc-jz4725b-codec.o + obj-$(CONFIG_SND_SOC_JZ4770_CODEC) += snd-soc-jz4770-codec.o +@@ -412,6 +417,7 @@ obj-$(CONFIG_SND_SOC_L3) += snd-soc-l3.o + obj-$(CONFIG_SND_SOC_LM4857) += snd-soc-lm4857.o + obj-$(CONFIG_SND_SOC_LM49453) += snd-soc-lm49453.o + obj-$(CONFIG_SND_SOC_LOCHNAGAR_SC) += snd-soc-lochnagar-sc.o ++obj-$(CONFIG_SND_SOC_MA120X0P) += snd-soc-ma120x0p.o + obj-$(CONFIG_SND_SOC_MADERA) += snd-soc-madera.o + obj-$(CONFIG_SND_SOC_MAX9759) += snd-soc-max9759.o + obj-$(CONFIG_SND_SOC_MAX9768) += snd-soc-max9768.o +@@ -465,6 +471,7 @@ obj-$(CONFIG_SND_SOC_PCM512x) += snd-soc + obj-$(CONFIG_SND_SOC_PCM512x_I2C) += snd-soc-pcm512x-i2c.o + obj-$(CONFIG_SND_SOC_PCM512x_SPI) += snd-soc-pcm512x-spi.o + obj-$(CONFIG_SND_SOC_RK3328) += snd-soc-rk3328.o ++obj-$(CONFIG_SND_SOC_PCM1794A) += snd-soc-pcm1794a.o + obj-$(CONFIG_SND_SOC_RL6231) += snd-soc-rl6231.o + obj-$(CONFIG_SND_SOC_RL6347A) += snd-soc-rl6347a.o + obj-$(CONFIG_SND_SOC_RT1011) += snd-soc-rt1011.o +@@ -526,6 +533,7 @@ obj-$(CONFIG_SND_SOC_TAS6424) += snd-soc + obj-$(CONFIG_SND_SOC_TDA7419) += snd-soc-tda7419.o + obj-$(CONFIG_SND_SOC_TAS2770) += snd-soc-tas2770.o + obj-$(CONFIG_SND_SOC_TFA9879) += snd-soc-tfa9879.o ++obj-$(CONFIG_SND_SOC_TAS5713) += snd-soc-tas5713.o + obj-$(CONFIG_SND_SOC_TLV320AIC23) += snd-soc-tlv320aic23.o + obj-$(CONFIG_SND_SOC_TLV320AIC23_I2C) += snd-soc-tlv320aic23-i2c.o + obj-$(CONFIG_SND_SOC_TLV320AIC23_SPI) += snd-soc-tlv320aic23-spi.o +--- a/sound/soc/codecs/cs42xx8-i2c.c ++++ b/sound/soc/codecs/cs42xx8-i2c.c +@@ -45,11 +45,18 @@ static struct i2c_device_id cs42xx8_i2c_ + }; + MODULE_DEVICE_TABLE(i2c, cs42xx8_i2c_id); + ++const struct of_device_id cs42xx8_i2c_of_match[] = { ++ { .compatible = "cirrus,cs42448", .data = &cs42448_data, }, ++ { .compatible = "cirrus,cs42888", .data = &cs42888_data, }, ++ { /* sentinel */ } ++}; ++MODULE_DEVICE_TABLE(of, cs42xx8_i2c_of_match); ++ + static struct i2c_driver cs42xx8_i2c_driver = { + .driver = { + .name = "cs42xx8", + .pm = &cs42xx8_pm, +- .of_match_table = cs42xx8_of_match, ++ .of_match_table = cs42xx8_i2c_of_match, + }, + .probe = cs42xx8_i2c_probe, + .remove = cs42xx8_i2c_remove, +--- a/sound/soc/codecs/cs42xx8.c ++++ b/sound/soc/codecs/cs42xx8.c +@@ -517,8 +517,10 @@ const struct of_device_id cs42xx8_of_mat + { .compatible = "cirrus,cs42888", .data = &cs42888_data, }, + { /* sentinel */ } + }; ++#if !IS_ENABLED(CONFIG_SND_SOC_CS42XX8_I2C) + MODULE_DEVICE_TABLE(of, cs42xx8_of_match); + EXPORT_SYMBOL_GPL(cs42xx8_of_match); ++#endif + + int cs42xx8_probe(struct device *dev, struct regmap *regmap) + { +--- /dev/null ++++ b/sound/soc/codecs/i-sabre-codec.c +@@ -0,0 +1,392 @@ ++/* ++ * Driver for I-Sabre Q2M ++ * ++ * Author: Satoru Kawase ++ * Modified by: Xiao Qingyong ++ * Modified by: JC BARBAUD (Mute) ++ * Update kernel v4.18+ by : Audiophonics ++ * Copyright 2018 Audiophonics ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "i-sabre-codec.h" ++ ++ ++/* I-Sabre Q2M Codec Private Data */ ++struct i_sabre_codec_priv { ++ struct regmap *regmap; ++ unsigned int fmt; ++}; ++ ++ ++/* I-Sabre Q2M Codec Default Register Value */ ++static const struct reg_default i_sabre_codec_reg_defaults[] = { ++ { ISABRECODEC_REG_10, 0x00 }, ++ { ISABRECODEC_REG_20, 0x00 }, ++ { ISABRECODEC_REG_21, 0x00 }, ++ { ISABRECODEC_REG_22, 0x00 }, ++ { ISABRECODEC_REG_24, 0x00 }, ++}; ++ ++ ++static bool i_sabre_codec_writeable(struct device *dev, unsigned int reg) ++{ ++ switch (reg) { ++ case ISABRECODEC_REG_10: ++ case ISABRECODEC_REG_20: ++ case ISABRECODEC_REG_21: ++ case ISABRECODEC_REG_22: ++ case ISABRECODEC_REG_24: ++ return true; ++ ++ default: ++ return false; ++ } ++} ++ ++static bool i_sabre_codec_readable(struct device *dev, unsigned int reg) ++{ ++ switch (reg) { ++ case ISABRECODEC_REG_01: ++ case ISABRECODEC_REG_02: ++ case ISABRECODEC_REG_10: ++ case ISABRECODEC_REG_20: ++ case ISABRECODEC_REG_21: ++ case ISABRECODEC_REG_22: ++ case ISABRECODEC_REG_24: ++ return true; ++ ++ default: ++ return false; ++ } ++} ++ ++static bool i_sabre_codec_volatile(struct device *dev, unsigned int reg) ++{ ++ switch (reg) { ++ case ISABRECODEC_REG_01: ++ case ISABRECODEC_REG_02: ++ return true; ++ ++ default: ++ return false; ++ } ++} ++ ++ ++/* Volume Scale */ ++static const DECLARE_TLV_DB_SCALE(volume_tlv, -10000, 100, 0); ++ ++ ++/* Filter Type */ ++static const char * const fir_filter_type_texts[] = { ++ "brick wall", ++ "corrected minimum phase fast", ++ "minimum phase slow", ++ "minimum phase fast", ++ "linear phase slow", ++ "linear phase fast", ++ "apodizing fast", ++}; ++ ++static SOC_ENUM_SINGLE_DECL(i_sabre_fir_filter_type_enum, ++ ISABRECODEC_REG_22, 0, fir_filter_type_texts); ++ ++ ++/* I2S / SPDIF Select */ ++static const char * const iis_spdif_sel_texts[] = { ++ "I2S", ++ "SPDIF", ++}; ++ ++static SOC_ENUM_SINGLE_DECL(i_sabre_iis_spdif_sel_enum, ++ ISABRECODEC_REG_24, 0, iis_spdif_sel_texts); ++ ++ ++/* Control */ ++static const struct snd_kcontrol_new i_sabre_codec_controls[] = { ++SOC_SINGLE_RANGE_TLV("Digital Playback Volume", ISABRECODEC_REG_20, 0, 0, 100, 1, volume_tlv), ++SOC_SINGLE("Digital Playback Switch", ISABRECODEC_REG_21, 0, 1, 1), ++SOC_ENUM("FIR Filter Type", i_sabre_fir_filter_type_enum), ++SOC_ENUM("I2S/SPDIF Select", i_sabre_iis_spdif_sel_enum), ++}; ++ ++ ++static const u32 i_sabre_codec_dai_rates_slave[] = { ++ 8000, 11025, 16000, 22050, 32000, ++ 44100, 48000, 64000, 88200, 96000, ++ 176400, 192000, 352800, 384000, ++ 705600, 768000, 1411200, 1536000 ++}; ++ ++static const struct snd_pcm_hw_constraint_list constraints_slave = { ++ .list = i_sabre_codec_dai_rates_slave, ++ .count = ARRAY_SIZE(i_sabre_codec_dai_rates_slave), ++}; ++ ++static int i_sabre_codec_dai_startup_slave( ++ struct snd_pcm_substream *substream, struct snd_soc_dai *dai) ++{ ++ struct snd_soc_component *component = dai->component; ++ int ret; ++ ++ ret = snd_pcm_hw_constraint_list(substream->runtime, ++ 0, SNDRV_PCM_HW_PARAM_RATE, &constraints_slave); ++ if (ret != 0) { ++ dev_err(component->card->dev, "Failed to setup rates constraints: %d\n", ret); ++ } ++ ++ return ret; ++} ++ ++static int i_sabre_codec_dai_startup( ++ struct snd_pcm_substream *substream, struct snd_soc_dai *dai) ++{ ++ struct snd_soc_component *component = dai->component; ++ struct i_sabre_codec_priv *i_sabre_codec ++ = snd_soc_component_get_drvdata(component); ++ ++ switch (i_sabre_codec->fmt & SND_SOC_DAIFMT_MASTER_MASK) { ++ case SND_SOC_DAIFMT_CBS_CFS: ++ return i_sabre_codec_dai_startup_slave(substream, dai); ++ ++ default: ++ return (-EINVAL); ++ } ++} ++ ++static int i_sabre_codec_hw_params( ++ struct snd_pcm_substream *substream, struct snd_pcm_hw_params *params, ++ struct snd_soc_dai *dai) ++{ ++ struct snd_soc_component *component = dai->component; ++ struct i_sabre_codec_priv *i_sabre_codec ++ = snd_soc_component_get_drvdata(component); ++ unsigned int daifmt; ++ int format_width; ++ ++ dev_dbg(component->card->dev, "hw_params %u Hz, %u channels\n", ++ params_rate(params), params_channels(params)); ++ ++ /* Check I2S Format (Bit Size) */ ++ format_width = snd_pcm_format_width(params_format(params)); ++ if ((format_width != 32) && (format_width != 16)) { ++ dev_err(component->card->dev, "Bad frame size: %d\n", ++ snd_pcm_format_width(params_format(params))); ++ return (-EINVAL); ++ } ++ ++ /* Check Slave Mode */ ++ daifmt = i_sabre_codec->fmt & SND_SOC_DAIFMT_MASTER_MASK; ++ if (daifmt != SND_SOC_DAIFMT_CBS_CFS) { ++ return (-EINVAL); ++ } ++ ++ /* Notify Sampling Frequency */ ++ switch (params_rate(params)) ++ { ++ case 44100: ++ case 48000: ++ case 88200: ++ case 96000: ++ case 176400: ++ case 192000: ++ snd_soc_component_update_bits(component, ISABRECODEC_REG_10, 0x01, 0x00); ++ break; ++ ++ case 352800: ++ case 384000: ++ case 705600: ++ case 768000: ++ case 1411200: ++ case 1536000: ++ snd_soc_component_update_bits(component, ISABRECODEC_REG_10, 0x01, 0x01); ++ break; ++ } ++ ++ return 0; ++} ++ ++static int i_sabre_codec_set_fmt(struct snd_soc_dai *dai, unsigned int fmt) ++{ ++ struct snd_soc_component *component = dai->component; ++ struct i_sabre_codec_priv *i_sabre_codec ++ = snd_soc_component_get_drvdata(component); ++ ++ /* interface format */ ++ switch (fmt & SND_SOC_DAIFMT_FORMAT_MASK) { ++ case SND_SOC_DAIFMT_I2S: ++ break; ++ ++ case SND_SOC_DAIFMT_RIGHT_J: ++ case SND_SOC_DAIFMT_LEFT_J: ++ default: ++ return (-EINVAL); ++ } ++ ++ /* clock inversion */ ++ if ((fmt & SND_SOC_DAIFMT_INV_MASK) != SND_SOC_DAIFMT_NB_NF) { ++ return (-EINVAL); ++ } ++ ++ /* Set Audio Data Format */ ++ i_sabre_codec->fmt = fmt; ++ ++ return 0; ++} ++ ++static int i_sabre_codec_dac_mute(struct snd_soc_dai *dai, int mute, int direction) ++{ ++ struct snd_soc_component *component = dai->component; ++ ++ if (mute) { ++ snd_soc_component_update_bits(component, ISABRECODEC_REG_21, 0x01, 0x01); ++ } else { ++ snd_soc_component_update_bits(component, ISABRECODEC_REG_21, 0x01, 0x00); ++ } ++ ++ return 0; ++} ++ ++ ++static const struct snd_soc_dai_ops i_sabre_codec_dai_ops = { ++ .startup = i_sabre_codec_dai_startup, ++ .hw_params = i_sabre_codec_hw_params, ++ .set_fmt = i_sabre_codec_set_fmt, ++ .mute_stream = i_sabre_codec_dac_mute, ++}; ++ ++static struct snd_soc_dai_driver i_sabre_codec_dai = { ++ .name = "i-sabre-codec-dai", ++ .playback = { ++ .stream_name = "Playback", ++ .channels_min = 2, ++ .channels_max = 2, ++ .rates = SNDRV_PCM_RATE_CONTINUOUS, ++ .rate_min = 8000, ++ .rate_max = 1536000, ++ .formats = SNDRV_PCM_FMTBIT_S16_LE ++ | SNDRV_PCM_FMTBIT_S32_LE, ++ }, ++ .ops = &i_sabre_codec_dai_ops, ++}; ++ ++static struct snd_soc_component_driver i_sabre_codec_codec_driver = { ++ .controls = i_sabre_codec_controls, ++ .num_controls = ARRAY_SIZE(i_sabre_codec_controls), ++}; ++ ++ ++static const struct regmap_config i_sabre_codec_regmap = { ++ .reg_bits = 8, ++ .val_bits = 8, ++ .max_register = ISABRECODEC_MAX_REG, ++ ++ .reg_defaults = i_sabre_codec_reg_defaults, ++ .num_reg_defaults = ARRAY_SIZE(i_sabre_codec_reg_defaults), ++ ++ .writeable_reg = i_sabre_codec_writeable, ++ .readable_reg = i_sabre_codec_readable, ++ .volatile_reg = i_sabre_codec_volatile, ++ ++ .cache_type = REGCACHE_RBTREE, ++}; ++ ++ ++static int i_sabre_codec_probe(struct device *dev, struct regmap *regmap) ++{ ++ struct i_sabre_codec_priv *i_sabre_codec; ++ int ret; ++ ++ i_sabre_codec = devm_kzalloc(dev, sizeof(*i_sabre_codec), GFP_KERNEL); ++ if (!i_sabre_codec) { ++ dev_err(dev, "devm_kzalloc"); ++ return (-ENOMEM); ++ } ++ ++ i_sabre_codec->regmap = regmap; ++ ++ dev_set_drvdata(dev, i_sabre_codec); ++ ++ ret = snd_soc_register_component(dev, ++ &i_sabre_codec_codec_driver, &i_sabre_codec_dai, 1); ++ if (ret != 0) { ++ dev_err(dev, "Failed to register CODEC: %d\n", ret); ++ return ret; ++ } ++ ++ return 0; ++} ++ ++static void i_sabre_codec_remove(struct device *dev) ++{ ++ snd_soc_unregister_component(dev); ++} ++ ++ ++static int i_sabre_codec_i2c_probe( ++ struct i2c_client *i2c, const struct i2c_device_id *id) ++{ ++ struct regmap *regmap; ++ ++ regmap = devm_regmap_init_i2c(i2c, &i_sabre_codec_regmap); ++ if (IS_ERR(regmap)) { ++ return PTR_ERR(regmap); ++ } ++ ++ return i_sabre_codec_probe(&i2c->dev, regmap); ++} ++ ++static int i_sabre_codec_i2c_remove(struct i2c_client *i2c) ++{ ++ i_sabre_codec_remove(&i2c->dev); ++ ++ return 0; ++} ++ ++ ++static const struct i2c_device_id i_sabre_codec_i2c_id[] = { ++ { "i-sabre-codec", }, ++ { } ++}; ++MODULE_DEVICE_TABLE(i2c, i_sabre_codec_i2c_id); ++ ++static const struct of_device_id i_sabre_codec_of_match[] = { ++ { .compatible = "audiophonics,i-sabre-codec", }, ++ { } ++}; ++MODULE_DEVICE_TABLE(of, i_sabre_codec_of_match); ++ ++static struct i2c_driver i_sabre_codec_i2c_driver = { ++ .driver = { ++ .name = "i-sabre-codec-i2c", ++ .owner = THIS_MODULE, ++ .of_match_table = of_match_ptr(i_sabre_codec_of_match), ++ }, ++ .probe = i_sabre_codec_i2c_probe, ++ .remove = i_sabre_codec_i2c_remove, ++ .id_table = i_sabre_codec_i2c_id, ++}; ++module_i2c_driver(i_sabre_codec_i2c_driver); ++ ++ ++MODULE_DESCRIPTION("ASoC I-Sabre Q2M codec driver"); ++MODULE_AUTHOR("Audiophonics "); ++MODULE_LICENSE("GPL"); +--- /dev/null ++++ b/sound/soc/codecs/i-sabre-codec.h +@@ -0,0 +1,42 @@ ++/* ++ * Driver for I-Sabre Q2M ++ * ++ * Author: Satoru Kawase ++ * Modified by: Xiao Qingyong ++ * Copyright 2018 Audiophonics ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#ifndef _SND_SOC_ISABRECODEC ++#define _SND_SOC_ISABRECODEC ++ ++ ++/* ISABRECODEC Register Address */ ++#define ISABRECODEC_REG_01 0x01 /* Virtual Device ID : 0x01 = es9038q2m */ ++#define ISABRECODEC_REG_02 0x02 /* API revision : 0x01 = Revision 01 */ ++#define ISABRECODEC_REG_10 0x10 /* 0x01 = above 192kHz, 0x00 = otherwise */ ++#define ISABRECODEC_REG_20 0x20 /* 0 - 100 (decimal value, 0 = min., 100 = max.) */ ++#define ISABRECODEC_REG_21 0x21 /* 0x00 = Mute OFF, 0x01 = Mute ON */ ++#define ISABRECODEC_REG_22 0x22 ++/* ++ 0x00 = brick wall, ++ 0x01 = corrected minimum phase fast, ++ 0x02 = minimum phase slow, ++ 0x03 = minimum phase fast, ++ 0x04 = linear phase slow, ++ 0x05 = linear phase fast, ++ 0x06 = apodizing fast, ++*/ ++//#define ISABRECODEC_REG_23 0x23 /* reserved */ ++#define ISABRECODEC_REG_24 0x24 /* 0x00 = I2S, 0x01 = SPDIF */ ++#define ISABRECODEC_MAX_REG 0x24 /* Maximum Register Number */ ++ ++#endif /* _SND_SOC_ISABRECODEC */ +--- /dev/null ++++ b/sound/soc/codecs/ma120x0p.c +@@ -0,0 +1,1384 @@ ++// SPDX-License-Identifier: GPL-2.0-or-later ++/* ++ * ASoC Driver for Infineon Merus(TM) ma120x0p multi-level class-D amplifier ++ * ++ * Authors: Ariel Muszkat ++ * Jorgen Kragh Jakobsen ++ * ++ * Copyright (C) 2019 Infineon Technologies AG ++ * ++ */ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++#ifndef _MA120X0P_ ++#define _MA120X0P_ ++//------------------------------------------------------------------manualPM--- ++// Select Manual PowerMode control ++#define ma_manualpm__a 0 ++#define ma_manualpm__len 1 ++#define ma_manualpm__mask 0x40 ++#define ma_manualpm__shift 0x06 ++#define ma_manualpm__reset 0x00 ++//--------------------------------------------------------------------pm_man--- ++// manual selected power mode ++#define ma_pm_man__a 0 ++#define ma_pm_man__len 2 ++#define ma_pm_man__mask 0x30 ++#define ma_pm_man__shift 0x04 ++#define ma_pm_man__reset 0x03 ++//------------------------------------------ ----------------------mthr_1to2--- ++// mod. index threshold value for pm1=>pm2 change. ++#define ma_mthr_1to2__a 1 ++#define ma_mthr_1to2__len 8 ++#define ma_mthr_1to2__mask 0xff ++#define ma_mthr_1to2__shift 0x00 ++#define ma_mthr_1to2__reset 0x3c ++//-----------------------------------------------------------------mthr_2to1--- ++// mod. index threshold value for pm2=>pm1 change. ++#define ma_mthr_2to1__a 2 ++#define ma_mthr_2to1__len 8 ++#define ma_mthr_2to1__mask 0xff ++#define ma_mthr_2to1__shift 0x00 ++#define ma_mthr_2to1__reset 0x32 ++//-----------------------------------------------------------------mthr_2to3--- ++// mod. index threshold value for pm2=>pm3 change. ++#define ma_mthr_2to3__a 3 ++#define ma_mthr_2to3__len 8 ++#define ma_mthr_2to3__mask 0xff ++#define ma_mthr_2to3__shift 0x00 ++#define ma_mthr_2to3__reset 0x5a ++//-----------------------------------------------------------------mthr_3to2--- ++// mod. index threshold value for pm3=>pm2 change. ++#define ma_mthr_3to2__a 4 ++#define ma_mthr_3to2__len 8 ++#define ma_mthr_3to2__mask 0xff ++#define ma_mthr_3to2__shift 0x00 ++#define ma_mthr_3to2__reset 0x50 ++//-------------------------------------------------------------pwmclkdiv_nom--- ++// pwm default clock divider value ++#define ma_pwmclkdiv_nom__a 8 ++#define ma_pwmclkdiv_nom__len 8 ++#define ma_pwmclkdiv_nom__mask 0xff ++#define ma_pwmclkdiv_nom__shift 0x00 ++#define ma_pwmclkdiv_nom__reset 0x26 ++//--------- ----------------------------------------------------ocp_latch_en--- ++// high to use permanently latching level-2 ocp ++#define ma_ocp_latch_en__a 10 ++#define ma_ocp_latch_en__len 1 ++#define ma_ocp_latch_en__mask 0x02 ++#define ma_ocp_latch_en__shift 0x01 ++#define ma_ocp_latch_en__reset 0x00 ++//---------------------------------------------------------------lf_clamp_en--- ++// high (default) to enable lf int2+3 clamping on clip ++#define ma_lf_clamp_en__a 10 ++#define ma_lf_clamp_en__len 1 ++#define ma_lf_clamp_en__mask 0x80 ++#define ma_lf_clamp_en__shift 0x07 ++#define ma_lf_clamp_en__reset 0x00 ++//-------------------------------------------------------pmcfg_btl_b.modtype--- ++// ++#define ma_pmcfg_btl_b__modtype__a 18 ++#define ma_pmcfg_btl_b__modtype__len 2 ++#define ma_pmcfg_btl_b__modtype__mask 0x18 ++#define ma_pmcfg_btl_b__modtype__shift 0x03 ++#define ma_pmcfg_btl_b__modtype__reset 0x02 ++//-------------------------------------------------------pmcfg_btl_b.freqdiv--- ++#define ma_pmcfg_btl_b__freqdiv__a 18 ++#define ma_pmcfg_btl_b__freqdiv__len 2 ++#define ma_pmcfg_btl_b__freqdiv__mask 0x06 ++#define ma_pmcfg_btl_b__freqdiv__shift 0x01 ++#define ma_pmcfg_btl_b__freqdiv__reset 0x01 ++//----------------------------------------------------pmcfg_btl_b.lf_gain_ol--- ++// ++#define ma_pmcfg_btl_b__lf_gain_ol__a 18 ++#define ma_pmcfg_btl_b__lf_gain_ol__len 1 ++#define ma_pmcfg_btl_b__lf_gain_ol__mask 0x01 ++#define ma_pmcfg_btl_b__lf_gain_ol__shift 0x00 ++#define ma_pmcfg_btl_b__lf_gain_ol__reset 0x01 ++//-------------------------------------------------------pmcfg_btl_c.freqdiv--- ++// ++#define ma_pmcfg_btl_c__freqdiv__a 19 ++#define ma_pmcfg_btl_c__freqdiv__len 2 ++#define ma_pmcfg_btl_c__freqdiv__mask 0x06 ++#define ma_pmcfg_btl_c__freqdiv__shift 0x01 ++#define ma_pmcfg_btl_c__freqdiv__reset 0x01 ++//-------------------------------------------------------pmcfg_btl_c.modtype--- ++// ++#define ma_pmcfg_btl_c__modtype__a 19 ++#define ma_pmcfg_btl_c__modtype__len 2 ++#define ma_pmcfg_btl_c__modtype__mask 0x18 ++#define ma_pmcfg_btl_c__modtype__shift 0x03 ++#define ma_pmcfg_btl_c__modtype__reset 0x01 ++//----------------------------------------------------pmcfg_btl_c.lf_gain_ol--- ++// ++#define ma_pmcfg_btl_c__lf_gain_ol__a 19 ++#define ma_pmcfg_btl_c__lf_gain_ol__len 1 ++#define ma_pmcfg_btl_c__lf_gain_ol__mask 0x01 ++#define ma_pmcfg_btl_c__lf_gain_ol__shift 0x00 ++#define ma_pmcfg_btl_c__lf_gain_ol__reset 0x00 ++//-------------------------------------------------------pmcfg_btl_d.modtype--- ++// ++#define ma_pmcfg_btl_d__modtype__a 20 ++#define ma_pmcfg_btl_d__modtype__len 2 ++#define ma_pmcfg_btl_d__modtype__mask 0x18 ++#define ma_pmcfg_btl_d__modtype__shift 0x03 ++#define ma_pmcfg_btl_d__modtype__reset 0x02 ++//-------------------------------------------------------pmcfg_btl_d.freqdiv--- ++// ++#define ma_pmcfg_btl_d__freqdiv__a 20 ++#define ma_pmcfg_btl_d__freqdiv__len 2 ++#define ma_pmcfg_btl_d__freqdiv__mask 0x06 ++#define ma_pmcfg_btl_d__freqdiv__shift 0x01 ++#define ma_pmcfg_btl_d__freqdiv__reset 0x02 ++//----------------------------------------------------pmcfg_btl_d.lf_gain_ol--- ++// ++#define ma_pmcfg_btl_d__lf_gain_ol__a 20 ++#define ma_pmcfg_btl_d__lf_gain_ol__len 1 ++#define ma_pmcfg_btl_d__lf_gain_ol__mask 0x01 ++#define ma_pmcfg_btl_d__lf_gain_ol__shift 0x00 ++#define ma_pmcfg_btl_d__lf_gain_ol__reset 0x00 ++//------------ -------------------------------------------pmcfg_se_a.modtype--- ++// ++#define ma_pmcfg_se_a__modtype__a 21 ++#define ma_pmcfg_se_a__modtype__len 2 ++#define ma_pmcfg_se_a__modtype__mask 0x18 ++#define ma_pmcfg_se_a__modtype__shift 0x03 ++#define ma_pmcfg_se_a__modtype__reset 0x01 ++//--------------------------------------------------------pmcfg_se_a.freqdiv--- ++// ++#define ma_pmcfg_se_a__freqdiv__a 21 ++#define ma_pmcfg_se_a__freqdiv__len 2 ++#define ma_pmcfg_se_a__freqdiv__mask 0x06 ++#define ma_pmcfg_se_a__freqdiv__shift 0x01 ++#define ma_pmcfg_se_a__freqdiv__reset 0x00 ++//-----------------------------------------------------pmcfg_se_a.lf_gain_ol--- ++// ++#define ma_pmcfg_se_a__lf_gain_ol__a 21 ++#define ma_pmcfg_se_a__lf_gain_ol__len 1 ++#define ma_pmcfg_se_a__lf_gain_ol__mask 0x01 ++#define ma_pmcfg_se_a__lf_gain_ol__shift 0x00 ++#define ma_pmcfg_se_a__lf_gain_ol__reset 0x01 ++//-----------------------------------------------------pmcfg_se_b.lf_gain_ol--- ++// ++#define ma_pmcfg_se_b__lf_gain_ol__a 22 ++#define ma_pmcfg_se_b__lf_gain_ol__len 1 ++#define ma_pmcfg_se_b__lf_gain_ol__mask 0x01 ++#define ma_pmcfg_se_b__lf_gain_ol__shift 0x00 ++#define ma_pmcfg_se_b__lf_gain_ol__reset 0x00 ++//--------------------------------------------------------pmcfg_se_b.freqdiv--- ++// ++#define ma_pmcfg_se_b__freqdiv__a 22 ++#define ma_pmcfg_se_b__freqdiv__len 2 ++#define ma_pmcfg_se_b__freqdiv__mask 0x06 ++#define ma_pmcfg_se_b__freqdiv__shift 0x01 ++#define ma_pmcfg_se_b__freqdiv__reset 0x01 ++//--------------------------------------------------------pmcfg_se_b.modtype--- ++// ++#define ma_pmcfg_se_b__modtype__a 22 ++#define ma_pmcfg_se_b__modtype__len 2 ++#define ma_pmcfg_se_b__modtype__mask 0x18 ++#define ma_pmcfg_se_b__modtype__shift 0x03 ++#define ma_pmcfg_se_b__modtype__reset 0x01 ++//----------------------------------------------------------balwaitcount_pm1--- ++// pm1 balancing period. ++#define ma_balwaitcount_pm1__a 23 ++#define ma_balwaitcount_pm1__len 8 ++#define ma_balwaitcount_pm1__mask 0xff ++#define ma_balwaitcount_pm1__shift 0x00 ++#define ma_balwaitcount_pm1__reset 0x14 ++//----------------------------------------------------------balwaitcount_pm2--- ++// pm2 balancing period. ++#define ma_balwaitcount_pm2__a 24 ++#define ma_balwaitcount_pm2__len 8 ++#define ma_balwaitcount_pm2__mask 0xff ++#define ma_balwaitcount_pm2__shift 0x00 ++#define ma_balwaitcount_pm2__reset 0x14 ++//----------------------------------------------------------balwaitcount_pm3--- ++// pm3 balancing period. ++#define ma_balwaitcount_pm3__a 25 ++#define ma_balwaitcount_pm3__len 8 ++#define ma_balwaitcount_pm3__mask 0xff ++#define ma_balwaitcount_pm3__shift 0x00 ++#define ma_balwaitcount_pm3__reset 0x1a ++//-------------------------------------------------------------usespread_pm1--- ++// pm1 pwm spread-spectrum mode on/off. ++#define ma_usespread_pm1__a 26 ++#define ma_usespread_pm1__len 1 ++#define ma_usespread_pm1__mask 0x40 ++#define ma_usespread_pm1__shift 0x06 ++#define ma_usespread_pm1__reset 0x00 ++//---------------------------------------------------------------dtsteps_pm1--- ++// pm1 dead time setting [10ns steps]. ++#define ma_dtsteps_pm1__a 26 ++#define ma_dtsteps_pm1__len 3 ++#define ma_dtsteps_pm1__mask 0x38 ++#define ma_dtsteps_pm1__shift 0x03 ++#define ma_dtsteps_pm1__reset 0x04 ++//---------------------------------------------------------------baltype_pm1--- ++// pm1 balancing sensor scheme. ++#define ma_baltype_pm1__a 26 ++#define ma_baltype_pm1__len 3 ++#define ma_baltype_pm1__mask 0x07 ++#define ma_baltype_pm1__shift 0x00 ++#define ma_baltype_pm1__reset 0x00 ++//-------------------------------------------------------------usespread_pm2--- ++// pm2 pwm spread-spectrum mode on/off. ++#define ma_usespread_pm2__a 27 ++#define ma_usespread_pm2__len 1 ++#define ma_usespread_pm2__mask 0x40 ++#define ma_usespread_pm2__shift 0x06 ++#define ma_usespread_pm2__reset 0x00 ++//---------------------------------------------------------------dtsteps_pm2--- ++// pm2 dead time setting [10ns steps]. ++#define ma_dtsteps_pm2__a 27 ++#define ma_dtsteps_pm2__len 3 ++#define ma_dtsteps_pm2__mask 0x38 ++#define ma_dtsteps_pm2__shift 0x03 ++#define ma_dtsteps_pm2__reset 0x03 ++//---------------------------------------------------------------baltype_pm2--- ++// pm2 balancing sensor scheme. ++#define ma_baltype_pm2__a 27 ++#define ma_baltype_pm2__len 3 ++#define ma_baltype_pm2__mask 0x07 ++#define ma_baltype_pm2__shift 0x00 ++#define ma_baltype_pm2__reset 0x01 ++//-------------------------------------------------------------usespread_pm3--- ++// pm3 pwm spread-spectrum mode on/off. ++#define ma_usespread_pm3__a 28 ++#define ma_usespread_pm3__len 1 ++#define ma_usespread_pm3__mask 0x40 ++#define ma_usespread_pm3__shift 0x06 ++#define ma_usespread_pm3__reset 0x00 ++//---------------------------------------------------------------dtsteps_pm3--- ++// pm3 dead time setting [10ns steps]. ++#define ma_dtsteps_pm3__a 28 ++#define ma_dtsteps_pm3__len 3 ++#define ma_dtsteps_pm3__mask 0x38 ++#define ma_dtsteps_pm3__shift 0x03 ++#define ma_dtsteps_pm3__reset 0x01 ++//---------------------------------------------------------------baltype_pm3--- ++// pm3 balancing sensor scheme. ++#define ma_baltype_pm3__a 28 ++#define ma_baltype_pm3__len 3 ++#define ma_baltype_pm3__mask 0x07 ++#define ma_baltype_pm3__shift 0x00 ++#define ma_baltype_pm3__reset 0x03 ++//-----------------------------------------------------------------pmprofile--- ++// pm profile select. valid presets: 0-1-2-3-4. 5=> custom profile. ++#define ma_pmprofile__a 29 ++#define ma_pmprofile__len 3 ++#define ma_pmprofile__mask 0x07 ++#define ma_pmprofile__shift 0x00 ++#define ma_pmprofile__reset 0x00 ++//-------------------------------------------------------------------pm3_man--- ++// custom profile pm3 contents. 0=>a, 1=>b, 2=>c, 3=>d ++#define ma_pm3_man__a 30 ++#define ma_pm3_man__len 2 ++#define ma_pm3_man__mask 0x30 ++#define ma_pm3_man__shift 0x04 ++#define ma_pm3_man__reset 0x02 ++//-------------------------------------------------------------------pm2_man--- ++// custom profile pm2 contents. 0=>a, 1=>b, 2=>c, 3=>d ++#define ma_pm2_man__a 30 ++#define ma_pm2_man__len 2 ++#define ma_pm2_man__mask 0x0c ++#define ma_pm2_man__shift 0x02 ++#define ma_pm2_man__reset 0x03 ++//-------------------------------------------------------------------pm1_man--- ++// custom profile pm1 contents. 0=>a, 1=>b, 2=>c, 3=>d ++#define ma_pm1_man__a 30 ++#define ma_pm1_man__len 2 ++#define ma_pm1_man__mask 0x03 ++#define ma_pm1_man__shift 0x00 ++#define ma_pm1_man__reset 0x03 ++//-----------------------------------------------------------ocp_latch_clear--- ++// low-high clears current ocp latched condition. ++#define ma_ocp_latch_clear__a 32 ++#define ma_ocp_latch_clear__len 1 ++#define ma_ocp_latch_clear__mask 0x80 ++#define ma_ocp_latch_clear__shift 0x07 ++#define ma_ocp_latch_clear__reset 0x00 ++//-------------------------------------------------------------audio_in_mode--- ++// audio input mode; 0-1-2-3-4-5 ++#define ma_audio_in_mode__a 37 ++#define ma_audio_in_mode__len 3 ++#define ma_audio_in_mode__mask 0xe0 ++#define ma_audio_in_mode__shift 0x05 ++#define ma_audio_in_mode__reset 0x00 ++//-----------------------------------------------------------------eh_dcshdn--- ++// high to enable dc protection ++#define ma_eh_dcshdn__a 38 ++#define ma_eh_dcshdn__len 1 ++#define ma_eh_dcshdn__mask 0x04 ++#define ma_eh_dcshdn__shift 0x02 ++#define ma_eh_dcshdn__reset 0x01 ++//---------------------------------------------------------audio_in_mode_ext--- ++// if set, audio_in_mode is controlled from audio_in_mode register. if not set ++//audio_in_mode is set from fuse bank setting ++#define ma_audio_in_mode_ext__a 39 ++#define ma_audio_in_mode_ext__len 1 ++#define ma_audio_in_mode_ext__mask 0x20 ++#define ma_audio_in_mode_ext__shift 0x05 ++#define ma_audio_in_mode_ext__reset 0x00 ++//------------------------------------------------------------------eh_clear--- ++// flip to clear error registers ++#define ma_eh_clear__a 45 ++#define ma_eh_clear__len 1 ++#define ma_eh_clear__mask 0x04 ++#define ma_eh_clear__shift 0x02 ++#define ma_eh_clear__reset 0x00 ++//----------------------------------------------------------thermal_compr_en--- ++// enable otw-contr. input compression? ++#define ma_thermal_compr_en__a 45 ++#define ma_thermal_compr_en__len 1 ++#define ma_thermal_compr_en__mask 0x20 ++#define ma_thermal_compr_en__shift 0x05 ++#define ma_thermal_compr_en__reset 0x01 ++//---------------------------------------------------------------system_mute--- ++// 1 = mute system, 0 = normal operation ++#define ma_system_mute__a 45 ++#define ma_system_mute__len 1 ++#define ma_system_mute__mask 0x40 ++#define ma_system_mute__shift 0x06 ++#define ma_system_mute__reset 0x00 ++//------------------------------------------------------thermal_compr_max_db--- ++// audio limiter max thermal reduction ++#define ma_thermal_compr_max_db__a 46 ++#define ma_thermal_compr_max_db__len 3 ++#define ma_thermal_compr_max_db__mask 0x07 ++#define ma_thermal_compr_max_db__shift 0x00 ++#define ma_thermal_compr_max_db__reset 0x04 ++//---------------------------------------------------------audio_proc_enable--- ++// enable audio proc, bypass if not enabled ++#define ma_audio_proc_enable__a 53 ++#define ma_audio_proc_enable__len 1 ++#define ma_audio_proc_enable__mask 0x08 ++#define ma_audio_proc_enable__shift 0x03 ++#define ma_audio_proc_enable__reset 0x00 ++//--------------------------------------------------------audio_proc_release--- ++// 00:slow, 01:normal, 10:fast ++#define ma_audio_proc_release__a 53 ++#define ma_audio_proc_release__len 2 ++#define ma_audio_proc_release__mask 0x30 ++#define ma_audio_proc_release__shift 0x04 ++#define ma_audio_proc_release__reset 0x00 ++//---------------------------------------------------------audio_proc_attack--- ++// 00:slow, 01:normal, 10:fast ++#define ma_audio_proc_attack__a 53 ++#define ma_audio_proc_attack__len 2 ++#define ma_audio_proc_attack__mask 0xc0 ++#define ma_audio_proc_attack__shift 0x06 ++#define ma_audio_proc_attack__reset 0x00 ++//----------------------------------------------------------------i2s_format--- ++// i2s basic data format, 000 = std. i2s, 001 = left justified (default) ++#define ma_i2s_format__a 53 ++#define ma_i2s_format__len 3 ++#define ma_i2s_format__mask 0x07 ++#define ma_i2s_format__shift 0x00 ++#define ma_i2s_format__reset 0x01 ++//--------------------------------------------------audio_proc_limiterenable--- ++// 1: enable limiter, 0: disable limiter ++#define ma_audio_proc_limiterenable__a 54 ++#define ma_audio_proc_limiterenable__len 1 ++#define ma_audio_proc_limiterenable__mask 0x40 ++#define ma_audio_proc_limiterenable__shift 0x06 ++#define ma_audio_proc_limiterenable__reset 0x00 ++//-----------------------------------------------------------audio_proc_mute--- ++// 1: mute, 0: unmute ++#define ma_audio_proc_mute__a 54 ++#define ma_audio_proc_mute__len 1 ++#define ma_audio_proc_mute__mask 0x80 ++#define ma_audio_proc_mute__shift 0x07 ++#define ma_audio_proc_mute__reset 0x00 ++//---------------------------------------------------------------i2s_sck_pol--- ++// i2s sck polarity cfg. 0 = rising edge data change ++#define ma_i2s_sck_pol__a 54 ++#define ma_i2s_sck_pol__len 1 ++#define ma_i2s_sck_pol__mask 0x01 ++#define ma_i2s_sck_pol__shift 0x00 ++#define ma_i2s_sck_pol__reset 0x01 ++//-------------------------------------------------------------i2s_framesize--- ++// i2s word length. 00 = 32bit, 01 = 24bit ++#define ma_i2s_framesize__a 54 ++#define ma_i2s_framesize__len 2 ++#define ma_i2s_framesize__mask 0x18 ++#define ma_i2s_framesize__shift 0x03 ++#define ma_i2s_framesize__reset 0x00 ++//----------------------------------------------------------------i2s_ws_pol--- ++// i2s ws polarity. 0 = low first ++#define ma_i2s_ws_pol__a 54 ++#define ma_i2s_ws_pol__len 1 ++#define ma_i2s_ws_pol__mask 0x02 ++#define ma_i2s_ws_pol__shift 0x01 ++#define ma_i2s_ws_pol__reset 0x00 ++//-----------------------------------------------------------------i2s_order--- ++// i2s word bit order. 0 = msb first ++#define ma_i2s_order__a 54 ++#define ma_i2s_order__len 1 ++#define ma_i2s_order__mask 0x04 ++#define ma_i2s_order__shift 0x02 ++#define ma_i2s_order__reset 0x00 ++//------------------------------------------------------------i2s_rightfirst--- ++// i2s l/r word order; 0 = left first ++#define ma_i2s_rightfirst__a 54 ++#define ma_i2s_rightfirst__len 1 ++#define ma_i2s_rightfirst__mask 0x20 ++#define ma_i2s_rightfirst__shift 0x05 ++#define ma_i2s_rightfirst__reset 0x00 ++//-------------------------------------------------------------vol_db_master--- ++// master volume db ++#define ma_vol_db_master__a 64 ++#define ma_vol_db_master__len 8 ++#define ma_vol_db_master__mask 0xff ++#define ma_vol_db_master__shift 0x00 ++#define ma_vol_db_master__reset 0x18 ++//------------------------------------------------------------vol_lsb_master--- ++// master volume lsb 1/4 steps ++#define ma_vol_lsb_master__a 65 ++#define ma_vol_lsb_master__len 2 ++#define ma_vol_lsb_master__mask 0x03 ++#define ma_vol_lsb_master__shift 0x00 ++#define ma_vol_lsb_master__reset 0x00 ++//----------------------------------------------------------------vol_db_ch0--- ++// volume channel 0 ++#define ma_vol_db_ch0__a 66 ++#define ma_vol_db_ch0__len 8 ++#define ma_vol_db_ch0__mask 0xff ++#define ma_vol_db_ch0__shift 0x00 ++#define ma_vol_db_ch0__reset 0x18 ++//----------------------------------------------------------------vol_db_ch1--- ++// volume channel 1 ++#define ma_vol_db_ch1__a 67 ++#define ma_vol_db_ch1__len 8 ++#define ma_vol_db_ch1__mask 0xff ++#define ma_vol_db_ch1__shift 0x00 ++#define ma_vol_db_ch1__reset 0x18 ++//----------------------------------------------------------------vol_db_ch2--- ++// volume channel 2 ++#define ma_vol_db_ch2__a 68 ++#define ma_vol_db_ch2__len 8 ++#define ma_vol_db_ch2__mask 0xff ++#define ma_vol_db_ch2__shift 0x00 ++#define ma_vol_db_ch2__reset 0x18 ++//----------------------------------------------------------------vol_db_ch3--- ++// volume channel 3 ++#define ma_vol_db_ch3__a 69 ++#define ma_vol_db_ch3__len 8 ++#define ma_vol_db_ch3__mask 0xff ++#define ma_vol_db_ch3__shift 0x00 ++#define ma_vol_db_ch3__reset 0x18 ++//---------------------------------------------------------------vol_lsb_ch0--- ++// volume channel 1 - 1/4 steps ++#define ma_vol_lsb_ch0__a 70 ++#define ma_vol_lsb_ch0__len 2 ++#define ma_vol_lsb_ch0__mask 0x03 ++#define ma_vol_lsb_ch0__shift 0x00 ++#define ma_vol_lsb_ch0__reset 0x00 ++//---------------------------------------------------------------vol_lsb_ch1--- ++// volume channel 3 - 1/4 steps ++#define ma_vol_lsb_ch1__a 70 ++#define ma_vol_lsb_ch1__len 2 ++#define ma_vol_lsb_ch1__mask 0x0c ++#define ma_vol_lsb_ch1__shift 0x02 ++#define ma_vol_lsb_ch1__reset 0x00 ++//---------------------------------------------------------------vol_lsb_ch2--- ++// volume channel 2 - 1/4 steps ++#define ma_vol_lsb_ch2__a 70 ++#define ma_vol_lsb_ch2__len 2 ++#define ma_vol_lsb_ch2__mask 0x30 ++#define ma_vol_lsb_ch2__shift 0x04 ++#define ma_vol_lsb_ch2__reset 0x00 ++//---------------------------------------------------------------vol_lsb_ch3--- ++// volume channel 3 - 1/4 steps ++#define ma_vol_lsb_ch3__a 70 ++#define ma_vol_lsb_ch3__len 2 ++#define ma_vol_lsb_ch3__mask 0xc0 ++#define ma_vol_lsb_ch3__shift 0x06 ++#define ma_vol_lsb_ch3__reset 0x00 ++//----------------------------------------------------------------thr_db_ch0--- ++// thr_db channel 0 ++#define ma_thr_db_ch0__a 71 ++#define ma_thr_db_ch0__len 8 ++#define ma_thr_db_ch0__mask 0xff ++#define ma_thr_db_ch0__shift 0x00 ++#define ma_thr_db_ch0__reset 0x18 ++//----------------------------------------------------------------thr_db_ch1--- ++// thr db ch1 ++#define ma_thr_db_ch1__a 72 ++#define ma_thr_db_ch1__len 8 ++#define ma_thr_db_ch1__mask 0xff ++#define ma_thr_db_ch1__shift 0x00 ++#define ma_thr_db_ch1__reset 0x18 ++//----------------------------------------------------------------thr_db_ch2--- ++// thr db ch2 ++#define ma_thr_db_ch2__a 73 ++#define ma_thr_db_ch2__len 8 ++#define ma_thr_db_ch2__mask 0xff ++#define ma_thr_db_ch2__shift 0x00 ++#define ma_thr_db_ch2__reset 0x18 ++//----------------------------------------------------------------thr_db_ch3--- ++// threshold db ch3 ++#define ma_thr_db_ch3__a 74 ++#define ma_thr_db_ch3__len 8 ++#define ma_thr_db_ch3__mask 0xff ++#define ma_thr_db_ch3__shift 0x00 ++#define ma_thr_db_ch3__reset 0x18 ++//---------------------------------------------------------------thr_lsb_ch0--- ++// thr lsb ch0 ++#define ma_thr_lsb_ch0__a 75 ++#define ma_thr_lsb_ch0__len 2 ++#define ma_thr_lsb_ch0__mask 0x03 ++#define ma_thr_lsb_ch0__shift 0x00 ++#define ma_thr_lsb_ch0__reset 0x00 ++//---------------------------------------------------------------thr_lsb_ch1--- ++// thr lsb ch1 ++#define ma_thr_lsb_ch1__a 75 ++#define ma_thr_lsb_ch1__len 2 ++#define ma_thr_lsb_ch1__mask 0x0c ++#define ma_thr_lsb_ch1__shift 0x02 ++#define ma_thr_lsb_ch1__reset 0x00 ++//---------------------------------------------------------------thr_lsb_ch2--- ++// thr lsb ch2 1/4 db step ++#define ma_thr_lsb_ch2__a 75 ++#define ma_thr_lsb_ch2__len 2 ++#define ma_thr_lsb_ch2__mask 0x30 ++#define ma_thr_lsb_ch2__shift 0x04 ++#define ma_thr_lsb_ch2__reset 0x00 ++//---------------------------------------------------------------thr_lsb_ch3--- ++// threshold lsb ch3 ++#define ma_thr_lsb_ch3__a 75 ++#define ma_thr_lsb_ch3__len 2 ++#define ma_thr_lsb_ch3__mask 0xc0 ++#define ma_thr_lsb_ch3__shift 0x06 ++#define ma_thr_lsb_ch3__reset 0x00 ++//-----------------------------------------------------------dcu_mon0.pm_mon--- ++// power mode monitor channel 0 ++#define ma_dcu_mon0__pm_mon__a 96 ++#define ma_dcu_mon0__pm_mon__len 2 ++#define ma_dcu_mon0__pm_mon__mask 0x03 ++#define ma_dcu_mon0__pm_mon__shift 0x00 ++#define ma_dcu_mon0__pm_mon__reset 0x00 ++//-----------------------------------------------------dcu_mon0.freqmode_mon--- ++// frequence mode monitor channel 0 ++#define ma_dcu_mon0__freqmode_mon__a 96 ++#define ma_dcu_mon0__freqmode_mon__len 3 ++#define ma_dcu_mon0__freqmode_mon__mask 0x70 ++#define ma_dcu_mon0__freqmode_mon__shift 0x04 ++#define ma_dcu_mon0__freqmode_mon__reset 0x00 ++//-------------------------------------------------------dcu_mon0.pps_passed--- ++// dcu0 pps completion indicator ++#define ma_dcu_mon0__pps_passed__a 96 ++#define ma_dcu_mon0__pps_passed__len 1 ++#define ma_dcu_mon0__pps_passed__mask 0x80 ++#define ma_dcu_mon0__pps_passed__shift 0x07 ++#define ma_dcu_mon0__pps_passed__reset 0x00 ++//----------------------------------------------------------dcu_mon0.ocp_mon--- ++// ocp monitor channel 0 ++#define ma_dcu_mon0__ocp_mon__a 97 ++#define ma_dcu_mon0__ocp_mon__len 1 ++#define ma_dcu_mon0__ocp_mon__mask 0x01 ++#define ma_dcu_mon0__ocp_mon__shift 0x00 ++#define ma_dcu_mon0__ocp_mon__reset 0x00 ++//--------------------------------------------------------dcu_mon0.vcfly1_ok--- ++// cfly1 protection monitor channel 0. ++#define ma_dcu_mon0__vcfly1_ok__a 97 ++#define ma_dcu_mon0__vcfly1_ok__len 1 ++#define ma_dcu_mon0__vcfly1_ok__mask 0x02 ++#define ma_dcu_mon0__vcfly1_ok__shift 0x01 ++#define ma_dcu_mon0__vcfly1_ok__reset 0x00 ++//--------------------------------------------------------dcu_mon0.vcfly2_ok--- ++// cfly2 protection monitor channel 0. ++#define ma_dcu_mon0__vcfly2_ok__a 97 ++#define ma_dcu_mon0__vcfly2_ok__len 1 ++#define ma_dcu_mon0__vcfly2_ok__mask 0x04 ++#define ma_dcu_mon0__vcfly2_ok__shift 0x02 ++#define ma_dcu_mon0__vcfly2_ok__reset 0x00 ++//----------------------------------------------------------dcu_mon0.pvdd_ok--- ++// dcu0 pvdd monitor ++#define ma_dcu_mon0__pvdd_ok__a 97 ++#define ma_dcu_mon0__pvdd_ok__len 1 ++#define ma_dcu_mon0__pvdd_ok__mask 0x08 ++#define ma_dcu_mon0__pvdd_ok__shift 0x03 ++#define ma_dcu_mon0__pvdd_ok__reset 0x00 ++//-----------------------------------------------------------dcu_mon0.vdd_ok--- ++// dcu0 vdd monitor ++#define ma_dcu_mon0__vdd_ok__a 97 ++#define ma_dcu_mon0__vdd_ok__len 1 ++#define ma_dcu_mon0__vdd_ok__mask 0x10 ++#define ma_dcu_mon0__vdd_ok__shift 0x04 ++#define ma_dcu_mon0__vdd_ok__reset 0x00 ++//-------------------------------------------------------------dcu_mon0.mute--- ++// dcu0 mute monitor ++#define ma_dcu_mon0__mute__a 97 ++#define ma_dcu_mon0__mute__len 1 ++#define ma_dcu_mon0__mute__mask 0x20 ++#define ma_dcu_mon0__mute__shift 0x05 ++#define ma_dcu_mon0__mute__reset 0x00 ++//------------------------------------------------------------dcu_mon0.m_mon--- ++// m sense monitor channel 0 ++#define ma_dcu_mon0__m_mon__a 98 ++#define ma_dcu_mon0__m_mon__len 8 ++#define ma_dcu_mon0__m_mon__mask 0xff ++#define ma_dcu_mon0__m_mon__shift 0x00 ++#define ma_dcu_mon0__m_mon__reset 0x00 ++//-----------------------------------------------------------dcu_mon1.pm_mon--- ++// power mode monitor channel 1 ++#define ma_dcu_mon1__pm_mon__a 100 ++#define ma_dcu_mon1__pm_mon__len 2 ++#define ma_dcu_mon1__pm_mon__mask 0x03 ++#define ma_dcu_mon1__pm_mon__shift 0x00 ++#define ma_dcu_mon1__pm_mon__reset 0x00 ++//-----------------------------------------------------dcu_mon1.freqmode_mon--- ++// frequence mode monitor channel 1 ++#define ma_dcu_mon1__freqmode_mon__a 100 ++#define ma_dcu_mon1__freqmode_mon__len 3 ++#define ma_dcu_mon1__freqmode_mon__mask 0x70 ++#define ma_dcu_mon1__freqmode_mon__shift 0x04 ++#define ma_dcu_mon1__freqmode_mon__reset 0x00 ++//-------------------------------------------------------dcu_mon1.pps_passed--- ++// dcu1 pps completion indicator ++#define ma_dcu_mon1__pps_passed__a 100 ++#define ma_dcu_mon1__pps_passed__len 1 ++#define ma_dcu_mon1__pps_passed__mask 0x80 ++#define ma_dcu_mon1__pps_passed__shift 0x07 ++#define ma_dcu_mon1__pps_passed__reset 0x00 ++//----------------------------------------------------------dcu_mon1.ocp_mon--- ++// ocp monitor channel 1 ++#define ma_dcu_mon1__ocp_mon__a 101 ++#define ma_dcu_mon1__ocp_mon__len 1 ++#define ma_dcu_mon1__ocp_mon__mask 0x01 ++#define ma_dcu_mon1__ocp_mon__shift 0x00 ++#define ma_dcu_mon1__ocp_mon__reset 0x00 ++//--------------------------------------------------------dcu_mon1.vcfly1_ok--- ++// cfly1 protcetion monitor channel 1 ++#define ma_dcu_mon1__vcfly1_ok__a 101 ++#define ma_dcu_mon1__vcfly1_ok__len 1 ++#define ma_dcu_mon1__vcfly1_ok__mask 0x02 ++#define ma_dcu_mon1__vcfly1_ok__shift 0x01 ++#define ma_dcu_mon1__vcfly1_ok__reset 0x00 ++//--------------------------------------------------------dcu_mon1.vcfly2_ok--- ++// cfly2 protection monitor channel 1 ++#define ma_dcu_mon1__vcfly2_ok__a 101 ++#define ma_dcu_mon1__vcfly2_ok__len 1 ++#define ma_dcu_mon1__vcfly2_ok__mask 0x04 ++#define ma_dcu_mon1__vcfly2_ok__shift 0x02 ++#define ma_dcu_mon1__vcfly2_ok__reset 0x00 ++//----------------------------------------------------------dcu_mon1.pvdd_ok--- ++// dcu1 pvdd monitor ++#define ma_dcu_mon1__pvdd_ok__a 101 ++#define ma_dcu_mon1__pvdd_ok__len 1 ++#define ma_dcu_mon1__pvdd_ok__mask 0x08 ++#define ma_dcu_mon1__pvdd_ok__shift 0x03 ++#define ma_dcu_mon1__pvdd_ok__reset 0x00 ++//-----------------------------------------------------------dcu_mon1.vdd_ok--- ++// dcu1 vdd monitor ++#define ma_dcu_mon1__vdd_ok__a 101 ++#define ma_dcu_mon1__vdd_ok__len 1 ++#define ma_dcu_mon1__vdd_ok__mask 0x10 ++#define ma_dcu_mon1__vdd_ok__shift 0x04 ++#define ma_dcu_mon1__vdd_ok__reset 0x00 ++//-------------------------------------------------------------dcu_mon1.mute--- ++// dcu1 mute monitor ++#define ma_dcu_mon1__mute__a 101 ++#define ma_dcu_mon1__mute__len 1 ++#define ma_dcu_mon1__mute__mask 0x20 ++#define ma_dcu_mon1__mute__shift 0x05 ++#define ma_dcu_mon1__mute__reset 0x00 ++//------------------------------------------------------------dcu_mon1.m_mon--- ++// m sense monitor channel 1 ++#define ma_dcu_mon1__m_mon__a 102 ++#define ma_dcu_mon1__m_mon__len 8 ++#define ma_dcu_mon1__m_mon__mask 0xff ++#define ma_dcu_mon1__m_mon__shift 0x00 ++#define ma_dcu_mon1__m_mon__reset 0x00 ++//--------------------------------------------------------dcu_mon0.sw_enable--- ++// dcu0 switch enable monitor ++#define ma_dcu_mon0__sw_enable__a 104 ++#define ma_dcu_mon0__sw_enable__len 1 ++#define ma_dcu_mon0__sw_enable__mask 0x40 ++#define ma_dcu_mon0__sw_enable__shift 0x06 ++#define ma_dcu_mon0__sw_enable__reset 0x00 ++//--------------------------------------------------------dcu_mon1.sw_enable--- ++// dcu1 switch enable monitor ++#define ma_dcu_mon1__sw_enable__a 104 ++#define ma_dcu_mon1__sw_enable__len 1 ++#define ma_dcu_mon1__sw_enable__mask 0x80 ++#define ma_dcu_mon1__sw_enable__shift 0x07 ++#define ma_dcu_mon1__sw_enable__reset 0x00 ++//------------------------------------------------------------hvboot0_ok_mon--- ++// hvboot0_ok for test/debug ++#define ma_hvboot0_ok_mon__a 105 ++#define ma_hvboot0_ok_mon__len 1 ++#define ma_hvboot0_ok_mon__mask 0x40 ++#define ma_hvboot0_ok_mon__shift 0x06 ++#define ma_hvboot0_ok_mon__reset 0x00 ++//------------------------------------------------------------hvboot1_ok_mon--- ++// hvboot1_ok for test/debug ++#define ma_hvboot1_ok_mon__a 105 ++#define ma_hvboot1_ok_mon__len 1 ++#define ma_hvboot1_ok_mon__mask 0x80 ++#define ma_hvboot1_ok_mon__shift 0x07 ++#define ma_hvboot1_ok_mon__reset 0x00 ++//-----------------------------------------------------------------error_acc--- ++// accumulated errors, at and after triggering ++#define ma_error_acc__a 109 ++#define ma_error_acc__len 8 ++#define ma_error_acc__mask 0xff ++#define ma_error_acc__shift 0x00 ++#define ma_error_acc__reset 0x00 ++//-------------------------------------------------------------i2s_data_rate--- ++// detected i2s data rate: 00/01/10 = x1/x2/x4 ++#define ma_i2s_data_rate__a 116 ++#define ma_i2s_data_rate__len 2 ++#define ma_i2s_data_rate__mask 0x03 ++#define ma_i2s_data_rate__shift 0x00 ++#define ma_i2s_data_rate__reset 0x00 ++//---------------------------------------------------------audio_in_mode_mon--- ++// audio input mode monitor ++#define ma_audio_in_mode_mon__a 116 ++#define ma_audio_in_mode_mon__len 3 ++#define ma_audio_in_mode_mon__mask 0x1c ++#define ma_audio_in_mode_mon__shift 0x02 ++#define ma_audio_in_mode_mon__reset 0x00 ++//------------------------------------------------------------------msel_mon--- ++// msel[2:0] monitor register ++#define ma_msel_mon__a 117 ++#define ma_msel_mon__len 3 ++#define ma_msel_mon__mask 0x07 ++#define ma_msel_mon__shift 0x00 ++#define ma_msel_mon__reset 0x00 ++//---------------------------------------------------------------------error--- ++// current error flag monitor reg - for app. ctrl. ++#define ma_error__a 124 ++#define ma_error__len 8 ++#define ma_error__mask 0xff ++#define ma_error__shift 0x00 ++#define ma_error__reset 0x00 ++//----------------------------------------------------audio_proc_limiter_mon--- ++// b7-b4: channel 3-0 limiter active ++#define ma_audio_proc_limiter_mon__a 126 ++#define ma_audio_proc_limiter_mon__len 4 ++#define ma_audio_proc_limiter_mon__mask 0xf0 ++#define ma_audio_proc_limiter_mon__shift 0x04 ++#define ma_audio_proc_limiter_mon__reset 0x00 ++//-------------------------------------------------------audio_proc_clip_mon--- ++// b3-b0: channel 3-0 clipping monitor ++#define ma_audio_proc_clip_mon__a 126 ++#define ma_audio_proc_clip_mon__len 4 ++#define ma_audio_proc_clip_mon__mask 0x0f ++#define ma_audio_proc_clip_mon__shift 0x00 ++#define ma_audio_proc_clip_mon__reset 0x00 ++#endif ++ ++#define SOC_ENUM_ERR(xname, xenum)\ ++{ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, .name = (xname),\ ++ .access = SNDRV_CTL_ELEM_ACCESS_READ,\ ++ .info = snd_soc_info_enum_double,\ ++ .get = snd_soc_get_enum_double, .put = snd_soc_put_enum_double,\ ++ .private_value = (unsigned long)&(xenum) } ++ ++static struct i2c_client *i2c; ++ ++struct ma120x0p_priv { ++ struct regmap *regmap; ++ int mclk_div; ++ struct snd_soc_component *component; ++ struct gpio_desc *enable_gpio; ++ struct gpio_desc *mute_gpio; ++ struct gpio_desc *booster_gpio; ++ struct gpio_desc *error_gpio; ++}; ++ ++static struct ma120x0p_priv *priv_data; ++ ++//Used to share the IRQ number within this file ++static unsigned int irqNumber; ++ ++// Function prototype for the custom IRQ handler function ++static irqreturn_t ma120x0p_irq_handler(int irq, void *data); ++ ++//Alsa Controls ++static const char * const limenable_text[] = {"Bypassed", "Enabled"}; ++static const char * const limatack_text[] = {"Slow", "Normal", "Fast"}; ++static const char * const limrelease_text[] = {"Slow", "Normal", "Fast"}; ++ ++static const char * const err_flycap_text[] = {"Ok", "Error"}; ++static const char * const err_overcurr_text[] = {"Ok", "Error"}; ++static const char * const err_pllerr_text[] = {"Ok", "Error"}; ++static const char * const err_pvddunder_text[] = {"Ok", "Error"}; ++static const char * const err_overtempw_text[] = {"Ok", "Error"}; ++static const char * const err_overtempe_text[] = {"Ok", "Error"}; ++static const char * const err_pinlowimp_text[] = {"Ok", "Error"}; ++static const char * const err_dcprot_text[] = {"Ok", "Error"}; ++ ++static const char * const pwr_mode_prof_text[] = {"PMF0", "PMF1", "PMF2", ++"PMF3", "PMF4"}; ++ ++static const struct soc_enum lim_enable_ctrl = ++ SOC_ENUM_SINGLE(ma_audio_proc_limiterenable__a, ++ ma_audio_proc_limiterenable__shift, ++ ma_audio_proc_limiterenable__len + 1, ++ limenable_text); ++static const struct soc_enum limatack_ctrl = ++ SOC_ENUM_SINGLE(ma_audio_proc_attack__a, ++ ma_audio_proc_attack__shift, ++ ma_audio_proc_attack__len + 1, ++ limatack_text); ++static const struct soc_enum limrelease_ctrl = ++ SOC_ENUM_SINGLE(ma_audio_proc_release__a, ++ ma_audio_proc_release__shift, ++ ma_audio_proc_release__len + 1, ++ limrelease_text); ++static const struct soc_enum err_flycap_ctrl = ++ SOC_ENUM_SINGLE(ma_error__a, 0, 3, err_flycap_text); ++static const struct soc_enum err_overcurr_ctrl = ++ SOC_ENUM_SINGLE(ma_error__a, 1, 3, err_overcurr_text); ++static const struct soc_enum err_pllerr_ctrl = ++ SOC_ENUM_SINGLE(ma_error__a, 2, 3, err_pllerr_text); ++static const struct soc_enum err_pvddunder_ctrl = ++ SOC_ENUM_SINGLE(ma_error__a, 3, 3, err_pvddunder_text); ++static const struct soc_enum err_overtempw_ctrl = ++ SOC_ENUM_SINGLE(ma_error__a, 4, 3, err_overtempw_text); ++static const struct soc_enum err_overtempe_ctrl = ++ SOC_ENUM_SINGLE(ma_error__a, 5, 3, err_overtempe_text); ++static const struct soc_enum err_pinlowimp_ctrl = ++ SOC_ENUM_SINGLE(ma_error__a, 6, 3, err_pinlowimp_text); ++static const struct soc_enum err_dcprot_ctrl = ++ SOC_ENUM_SINGLE(ma_error__a, 7, 3, err_dcprot_text); ++static const struct soc_enum pwr_mode_prof_ctrl = ++ SOC_ENUM_SINGLE(ma_pmprofile__a, ma_pmprofile__shift, 5, ++ pwr_mode_prof_text); ++ ++static const char * const pwr_mode_texts[] = { ++ "Dynamic power mode", ++ "Power mode 1", ++ "Power mode 2", ++ "Power mode 3", ++ }; ++ ++static const int pwr_mode_values[] = { ++ 0x10, ++ 0x50, ++ 0x60, ++ 0x70, ++ }; ++ ++static const SOC_VALUE_ENUM_SINGLE_DECL(pwr_mode_ctrl, ++ ma_pm_man__a, 0, 0x70, ++ pwr_mode_texts, ++ pwr_mode_values); ++ ++static const DECLARE_TLV_DB_SCALE(ma120x0p_vol_tlv, -5000, 100, 0); ++static const DECLARE_TLV_DB_SCALE(ma120x0p_lim_tlv, -5000, 100, 0); ++static const DECLARE_TLV_DB_SCALE(ma120x0p_lr_tlv, -5000, 100, 0); ++ ++static const struct snd_kcontrol_new ma120x0p_snd_controls[] = { ++ //Master Volume ++ SOC_SINGLE_RANGE_TLV("A.Mstr Vol Volume", ++ ma_vol_db_master__a, 0, 0x18, 0x4a, 1, ma120x0p_vol_tlv), ++ ++ //L-R Volume ch0 ++ SOC_SINGLE_RANGE_TLV("B.L Vol Volume", ++ ma_vol_db_ch0__a, 0, 0x18, 0x4a, 1, ma120x0p_lr_tlv), ++ SOC_SINGLE_RANGE_TLV("C.R Vol Volume", ++ ma_vol_db_ch1__a, 0, 0x18, 0x4a, 1, ma120x0p_lr_tlv), ++ ++ //L-R Limiter Threshold ch0-ch1 ++ SOC_DOUBLE_R_RANGE_TLV("D.Lim thresh Volume", ++ ma_thr_db_ch0__a, ma_thr_db_ch1__a, 0, 0x0e, 0x4a, 1, ++ ma120x0p_lim_tlv), ++ ++ //Enum Switches/Selectors ++ //SOC_ENUM("E.AudioProc Mute", audioproc_mute_ctrl), ++ SOC_ENUM("F.Limiter Enable", lim_enable_ctrl), ++ SOC_ENUM("G.Limiter Attck", limatack_ctrl), ++ SOC_ENUM("H.Limiter Rls", limrelease_ctrl), ++ ++ //Enum Error Monitor (read-only) ++ SOC_ENUM_ERR("I.Err flycap", err_flycap_ctrl), ++ SOC_ENUM_ERR("J.Err overcurr", err_overcurr_ctrl), ++ SOC_ENUM_ERR("K.Err pllerr", err_pllerr_ctrl), ++ SOC_ENUM_ERR("L.Err pvddunder", err_pvddunder_ctrl), ++ SOC_ENUM_ERR("M.Err overtempw", err_overtempw_ctrl), ++ SOC_ENUM_ERR("N.Err overtempe", err_overtempe_ctrl), ++ SOC_ENUM_ERR("O.Err pinlowimp", err_pinlowimp_ctrl), ++ SOC_ENUM_ERR("P.Err dcprot", err_dcprot_ctrl), ++ ++ //Power modes profiles ++ SOC_ENUM("Q.PM Prof", pwr_mode_prof_ctrl), ++ ++ // Power mode selection (Dynamic,1,2,3) ++ SOC_ENUM("R.Power Mode", pwr_mode_ctrl), ++}; ++ ++//Machine Driver ++static int ma120x0p_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params, struct snd_soc_dai *dai) ++{ ++ u16 blen = 0x00; ++ ++ struct snd_soc_component *component = dai->component; ++ ++ priv_data->component = component; ++ ++ switch (params_format(params)) { ++ case SNDRV_PCM_FORMAT_S16_LE: ++ blen = 0x10; ++ break; ++ case SNDRV_PCM_FORMAT_S24_LE: ++ blen = 0x00; ++ break; ++ case SNDRV_PCM_FORMAT_S32_LE: ++ blen = 0x00; ++ break; ++ default: ++ dev_err(dai->dev, "Unsupported word length: %u\n", ++ params_format(params)); ++ return -EINVAL; ++ } ++ ++ // set word length ++ snd_soc_component_update_bits(component, ma_i2s_framesize__a, ++ ma_i2s_framesize__mask, blen); ++ ++ return 0; ++} ++ ++static int ma120x0p_mute_stream(struct snd_soc_dai *dai, int mute, int stream) ++{ ++ int val = 0; ++ ++ struct ma120x0p_priv *ma120x0p; ++ ++ struct snd_soc_component *component = dai->component; ++ ++ ma120x0p = snd_soc_component_get_drvdata(component); ++ ++ if (mute) ++ val = 0; ++ else ++ val = 1; ++ ++ gpiod_set_value_cansleep(priv_data->mute_gpio, val); ++ ++ return 0; ++} ++ ++static const struct snd_soc_dai_ops ma120x0p_dai_ops = { ++ .hw_params = ma120x0p_hw_params, ++ .mute_stream = ma120x0p_mute_stream, ++}; ++ ++static struct snd_soc_dai_driver ma120x0p_dai = { ++ .name = "ma120x0p-amp", ++ .playback = { ++ .stream_name = "Playback", ++ .channels_min = 2, ++ .channels_max = 2, ++ .rates = SNDRV_PCM_RATE_CONTINUOUS, ++ .rate_min = 44100, ++ .rate_max = 96000, ++ .formats = SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32_LE ++ }, ++ .ops = &ma120x0p_dai_ops, ++}; ++ ++//Codec Driver ++static int ma120x0p_clear_err(struct snd_soc_component *component) ++{ ++ int ret = 0; ++ ++ struct ma120x0p_priv *ma120x0p; ++ ++ ma120x0p = snd_soc_component_get_drvdata(component); ++ ++ ret = snd_soc_component_update_bits(component, ++ ma_eh_clear__a, ma_eh_clear__mask, 0x00); ++ if (ret < 0) ++ return ret; ++ ++ ret = snd_soc_component_update_bits(component, ++ ma_eh_clear__a, ma_eh_clear__mask, 0x04); ++ if (ret < 0) ++ return ret; ++ ++ ret = snd_soc_component_update_bits(component, ++ ma_eh_clear__a, ma_eh_clear__mask, 0x00); ++ if (ret < 0) ++ return ret; ++ ++ return 0; ++} ++ ++static void ma120x0p_remove(struct snd_soc_component *component) ++{ ++ struct ma120x0p_priv *ma120x0p; ++ ++ ma120x0p = snd_soc_component_get_drvdata(component); ++} ++ ++static int ma120x0p_probe(struct snd_soc_component *component) ++{ ++ struct ma120x0p_priv *ma120x0p; ++ ++ int ret = 0; ++ ++ i2c = container_of(component->dev, struct i2c_client, dev); ++ ++ ma120x0p = snd_soc_component_get_drvdata(component); ++ ++ //Reset error ++ ma120x0p_clear_err(component); ++ if (ret < 0) ++ return ret; ++ ++ // set serial audio format I2S and enable audio processor ++ ret = snd_soc_component_write(component, ma_i2s_format__a, 0x08); ++ if (ret < 0) ++ return ret; ++ ++ // Enable audio limiter ++ ret = snd_soc_component_update_bits(component, ++ ma_audio_proc_limiterenable__a, ++ ma_audio_proc_limiterenable__mask, 0x40); ++ if (ret < 0) ++ return ret; ++ ++ // Set lim attack to fast ++ ret = snd_soc_component_update_bits(component, ++ ma_audio_proc_attack__a, ma_audio_proc_attack__mask, 0x80); ++ if (ret < 0) ++ return ret; ++ ++ // Set lim attack to low ++ ret = snd_soc_component_update_bits(component, ++ ma_audio_proc_release__a, ma_audio_proc_release__mask, 0x00); ++ if (ret < 0) ++ return ret; ++ ++ // set volume to 0dB ++ ret = snd_soc_component_write(component, ma_vol_db_master__a, 0x18); ++ if (ret < 0) ++ return ret; ++ ++ // set ch0 lim thresh to -15dB ++ ret = snd_soc_component_write(component, ma_thr_db_ch0__a, 0x27); ++ if (ret < 0) ++ return ret; ++ ++ // set ch1 lim thresh to -15dB ++ ret = snd_soc_component_write(component, ma_thr_db_ch1__a, 0x27); ++ if (ret < 0) ++ return ret; ++ ++ //Check for errors ++ ret = snd_soc_component_test_bits(component, ma_error_acc__a, 0x00, 0); ++ if (ret < 0) ++ return ret; ++ ret = snd_soc_component_test_bits(component, ma_error_acc__a, 0x01, 0); ++ if (ret < 0) ++ return ret; ++ ret = snd_soc_component_test_bits(component, ma_error_acc__a, 0x02, 0); ++ if (ret < 0) ++ return ret; ++ ret = snd_soc_component_test_bits(component, ma_error_acc__a, 0x08, 0); ++ if (ret < 0) ++ return ret; ++ ret = snd_soc_component_test_bits(component, ma_error_acc__a, 0x10, 0); ++ if (ret < 0) ++ return ret; ++ ret = snd_soc_component_test_bits(component, ma_error_acc__a, 0x20, 0); ++ if (ret < 0) ++ return ret; ++ ret = snd_soc_component_test_bits(component, ma_error_acc__a, 0x40, 0); ++ if (ret < 0) ++ return ret; ++ ret = snd_soc_component_test_bits(component, ma_error_acc__a, 0x80, 0); ++ if (ret < 0) ++ return ret; ++ ++ return 0; ++} ++ ++static int ma120x0p_set_bias_level(struct snd_soc_component *component, ++ enum snd_soc_bias_level level) ++{ ++ int ret = 0; ++ ++ struct ma120x0p_priv *ma120x0p; ++ ++ ma120x0p = snd_soc_component_get_drvdata(component); ++ ++ switch (level) { ++ case SND_SOC_BIAS_ON: ++ break; ++ ++ case SND_SOC_BIAS_PREPARE: ++ break; ++ ++ case SND_SOC_BIAS_STANDBY: ++ ret = gpiod_get_value_cansleep(priv_data->enable_gpio); ++ if (ret != 0) { ++ dev_err(component->dev, "Device ma120x0p disabled in STANDBY BIAS: %d\n", ++ ret); ++ return ret; ++ } ++ break; ++ ++ case SND_SOC_BIAS_OFF: ++ break; ++ } ++ ++ return 0; ++} ++ ++static const struct snd_soc_dapm_widget ma120x0p_dapm_widgets[] = { ++ SND_SOC_DAPM_OUTPUT("OUT_A"), ++ SND_SOC_DAPM_OUTPUT("OUT_B"), ++}; ++ ++static const struct snd_soc_dapm_route ma120x0p_dapm_routes[] = { ++ { "OUT_B", NULL, "Playback" }, ++ { "OUT_A", NULL, "Playback" }, ++}; ++ ++static const struct snd_soc_component_driver ma120x0p_component_driver = { ++ .probe = ma120x0p_probe, ++ .remove = ma120x0p_remove, ++ .set_bias_level = ma120x0p_set_bias_level, ++ .dapm_widgets = ma120x0p_dapm_widgets, ++ .num_dapm_widgets = ARRAY_SIZE(ma120x0p_dapm_widgets), ++ .dapm_routes = ma120x0p_dapm_routes, ++ .num_dapm_routes = ARRAY_SIZE(ma120x0p_dapm_routes), ++ .controls = ma120x0p_snd_controls, ++ .num_controls = ARRAY_SIZE(ma120x0p_snd_controls), ++ .use_pmdown_time = 1, ++ .endianness = 1, ++ .non_legacy_dai_naming = 1, ++}; ++ ++//I2C Driver ++static const struct reg_default ma120x0p_reg_defaults[] = { ++ { 0x01, 0x3c }, ++}; ++ ++static bool ma120x0p_reg_volatile(struct device *dev, unsigned int reg) ++{ ++ switch (reg) { ++ case ma_error__a: ++ return true; ++ default: ++ return false; ++ } ++} ++ ++static const struct of_device_id ma120x0p_of_match[] = { ++ { .compatible = "ma,ma120x0p", }, ++ { } ++}; ++ ++MODULE_DEVICE_TABLE(of, ma120x0p_of_match); ++ ++static struct regmap_config ma120x0p_regmap_config = { ++ .reg_bits = 8, ++ .val_bits = 8, ++ ++ .max_register = 255, ++ .volatile_reg = ma120x0p_reg_volatile, ++ ++ .cache_type = REGCACHE_RBTREE, ++ .reg_defaults = ma120x0p_reg_defaults, ++ .num_reg_defaults = ARRAY_SIZE(ma120x0p_reg_defaults), ++}; ++ ++static int ma120x0p_i2c_probe(struct i2c_client *i2c, ++ const struct i2c_device_id *id) ++{ ++ int ret; ++ ++ priv_data = devm_kzalloc(&i2c->dev, sizeof(*priv_data), GFP_KERNEL); ++ if (!priv_data) ++ return -ENOMEM; ++ i2c_set_clientdata(i2c, priv_data); ++ ++ priv_data->regmap = devm_regmap_init_i2c(i2c, &ma120x0p_regmap_config); ++ if (IS_ERR(priv_data->regmap)) { ++ ret = PTR_ERR(priv_data->regmap); ++ return ret; ++ } ++ ++ //Startup sequence ++ ++ //Make sure the device is muted ++ priv_data->mute_gpio = devm_gpiod_get_optional(&i2c->dev, "mute_gp", ++ GPIOD_OUT_LOW); ++ if (IS_ERR(priv_data->mute_gpio)) { ++ ret = PTR_ERR(priv_data->mute_gpio); ++ dev_err(&i2c->dev, "Failed to get mute gpio line: %d\n", ret); ++ return ret; ++ } ++ msleep(50); ++ ++// MA120xx0P devices are usually powered by an integrated boost converter. ++// An option GPIO control line is provided to enable the booster properly and ++// in sync with the enable and mute GPIO lines. ++ priv_data->booster_gpio = devm_gpiod_get_optional(&i2c->dev, ++ "booster_gp", GPIOD_OUT_LOW); ++ if (IS_ERR(priv_data->booster_gpio)) { ++ ret = PTR_ERR(priv_data->booster_gpio); ++ dev_err(&i2c->dev, ++ "Failed to get booster enable gpio line: %d\n", ret); ++ return ret; ++ } ++ msleep(50); ++ ++ //Enable booster and wait 200ms until stable PVDD ++ gpiod_set_value_cansleep(priv_data->booster_gpio, 1); ++ msleep(200); ++ ++ //Enable ma120x0pp ++ priv_data->enable_gpio = devm_gpiod_get_optional(&i2c->dev, ++ "enable_gp", GPIOD_OUT_LOW); ++ if (IS_ERR(priv_data->enable_gpio)) { ++ ret = PTR_ERR(priv_data->enable_gpio); ++ dev_err(&i2c->dev, ++ "Failed to get ma120x0p enable gpio line: %d\n", ret); ++ return ret; ++ } ++ msleep(50); ++ ++ //Optional use of ma120x0pp error line as an interrupt trigger to ++ //platform GPIO. ++ //Get error input gpio ma120x0p ++ priv_data->error_gpio = devm_gpiod_get_optional(&i2c->dev, ++ "error_gp", GPIOD_IN); ++ if (IS_ERR(priv_data->error_gpio)) { ++ ret = PTR_ERR(priv_data->error_gpio); ++ dev_err(&i2c->dev, ++ "Failed to get ma120x0p error gpio line: %d\n", ret); ++ return ret; ++ } ++ ++ if (priv_data->error_gpio != NULL) { ++ irqNumber = gpiod_to_irq(priv_data->error_gpio); ++ ++ ret = devm_request_threaded_irq(&i2c->dev, ++ irqNumber, ma120x0p_irq_handler, ++ NULL, IRQF_TRIGGER_FALLING, ++ "ma120x0p", priv_data); ++ if (ret != 0) ++ dev_warn(&i2c->dev, "Failed to request IRQ: %d\n", ++ ret); ++ } ++ ++ ret = devm_snd_soc_register_component(&i2c->dev, ++ &ma120x0p_component_driver, &ma120x0p_dai, 1); ++ ++ return ret; ++} ++ ++static irqreturn_t ma120x0p_irq_handler(int irq, void *data) ++{ ++ gpiod_set_value_cansleep(priv_data->mute_gpio, 0); ++ gpiod_set_value_cansleep(priv_data->enable_gpio, 1); ++ return IRQ_HANDLED; ++} ++ ++static int ma120x0p_i2c_remove(struct i2c_client *i2c) ++{ ++ snd_soc_unregister_component(&i2c->dev); ++ i2c_set_clientdata(i2c, NULL); ++ ++ gpiod_set_value_cansleep(priv_data->mute_gpio, 0); ++ msleep(30); ++ gpiod_set_value_cansleep(priv_data->enable_gpio, 1); ++ msleep(200); ++ gpiod_set_value_cansleep(priv_data->booster_gpio, 0); ++ msleep(200); ++ ++ kfree(priv_data); ++ ++ return 0; ++} ++ ++static void ma120x0p_i2c_shutdown(struct i2c_client *i2c) ++{ ++ snd_soc_unregister_component(&i2c->dev); ++ i2c_set_clientdata(i2c, NULL); ++ ++ gpiod_set_value_cansleep(priv_data->mute_gpio, 0); ++ msleep(30); ++ gpiod_set_value_cansleep(priv_data->enable_gpio, 1); ++ msleep(200); ++ gpiod_set_value_cansleep(priv_data->booster_gpio, 0); ++ msleep(200); ++ ++ kfree(priv_data); ++} ++ ++static const struct i2c_device_id ma120x0p_i2c_id[] = { ++ { "ma120x0p", 0 }, ++ { } ++}; ++ ++MODULE_DEVICE_TABLE(i2c, ma120x0p_i2c_id); ++ ++static struct i2c_driver ma120x0p_i2c_driver = { ++ .driver = { ++ .name = "ma120x0p", ++ .owner = THIS_MODULE, ++ .of_match_table = ma120x0p_of_match, ++ }, ++ .probe = ma120x0p_i2c_probe, ++ .remove = ma120x0p_i2c_remove, ++ .shutdown = ma120x0p_i2c_shutdown, ++ .id_table = ma120x0p_i2c_id ++}; ++ ++static int __init ma120x0p_modinit(void) ++{ ++ int ret = 0; ++ ++ ret = i2c_add_driver(&ma120x0p_i2c_driver); ++ if (ret != 0) { ++ pr_err("Failed to register MA120X0P I2C driver: %d\n", ret); ++ return ret; ++ } ++ return ret; ++} ++module_init(ma120x0p_modinit); ++ ++static void __exit ma120x0p_exit(void) ++{ ++ i2c_del_driver(&ma120x0p_i2c_driver); ++} ++module_exit(ma120x0p_exit); ++ ++MODULE_AUTHOR("Ariel Muszkat ariel.muszkat@gmail.com>"); ++MODULE_DESCRIPTION("ASoC driver for ma120x0p"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/codecs/pcm1794a.c +@@ -0,0 +1,69 @@ ++/* ++ * Driver for the PCM1794A codec ++ * ++ * Author: Florian Meier ++ * Copyright 2013 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++ ++#include ++#include ++#include ++ ++#include ++ ++static struct snd_soc_dai_driver pcm1794a_dai = { ++ .name = "pcm1794a-hifi", ++ .playback = { ++ .channels_min = 2, ++ .channels_max = 2, ++ .rates = SNDRV_PCM_RATE_8000_192000, ++ .formats = SNDRV_PCM_FMTBIT_S16_LE | ++ SNDRV_PCM_FMTBIT_S24_LE ++ }, ++}; ++ ++static struct snd_soc_component_driver soc_component_dev_pcm1794a; ++ ++static int pcm1794a_probe(struct platform_device *pdev) ++{ ++ return snd_soc_register_component(&pdev->dev, &soc_component_dev_pcm1794a, ++ &pcm1794a_dai, 1); ++} ++ ++static int pcm1794a_remove(struct platform_device *pdev) ++{ ++ snd_soc_unregister_component(&pdev->dev); ++ return 0; ++} ++ ++static const struct of_device_id pcm1794a_of_match[] = { ++ { .compatible = "ti,pcm1794a", }, ++ { } ++}; ++MODULE_DEVICE_TABLE(of, pcm1794a_of_match); ++ ++static struct platform_driver pcm1794a_component_driver = { ++ .probe = pcm1794a_probe, ++ .remove = pcm1794a_remove, ++ .driver = { ++ .name = "pcm1794a-codec", ++ .owner = THIS_MODULE, ++ .of_match_table = of_match_ptr(pcm1794a_of_match), ++ }, ++}; ++ ++module_platform_driver(pcm1794a_component_driver); ++ ++MODULE_DESCRIPTION("ASoC PCM1794A codec driver"); ++MODULE_AUTHOR("Florian Meier "); ++MODULE_LICENSE("GPL v2"); +--- a/sound/soc/codecs/pcm512x.c ++++ b/sound/soc/codecs/pcm512x.c +@@ -534,7 +534,7 @@ static unsigned long pcm512x_ncp_target( + + static const u32 pcm512x_dai_rates[] = { + 8000, 11025, 16000, 22050, 32000, 44100, 48000, 64000, +- 88200, 96000, 176400, 192000, 384000, ++ 88200, 96000, 176400, 192000, 352800, 384000, + }; + + static const struct snd_pcm_hw_constraint_list constraints_slave = { +--- /dev/null ++++ b/sound/soc/codecs/tas5713.c +@@ -0,0 +1,363 @@ ++/* ++ * ASoC Driver for TAS5713 ++ * ++ * Author: Sebastian Eickhoff ++ * Copyright 2014 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++#include "tas5713.h" ++ ++ ++static struct i2c_client *i2c; ++ ++struct tas5713_priv { ++ struct regmap *regmap; ++ int mclk_div; ++ struct snd_soc_component *component; ++}; ++ ++static struct tas5713_priv *priv_data; ++ ++ ++ ++ ++/* ++ * _ _ ___ _ ___ _ _ ++ * /_\ | | / __| /_\ / __|___ _ _| |_ _ _ ___| |___ ++ * / _ \| |__\__ \/ _ \ | (__/ _ \ ' \ _| '_/ _ \ (_-< ++ * /_/ \_\____|___/_/ \_\ \___\___/_||_\__|_| \___/_/__/ ++ * ++ */ ++ ++static const DECLARE_TLV_DB_SCALE(tas5713_vol_tlv, -10000, 50, 1); ++ ++ ++static const struct snd_kcontrol_new tas5713_snd_controls[] = { ++ SOC_SINGLE_TLV ("Master" , TAS5713_VOL_MASTER, 0, 248, 1, tas5713_vol_tlv), ++ SOC_DOUBLE_R_TLV("Channels" , TAS5713_VOL_CH1, TAS5713_VOL_CH2, 0, 248, 1, tas5713_vol_tlv) ++}; ++ ++ ++ ++ ++/* ++ * __ __ _ _ ___ _ ++ * | \/ |__ _ __| |_ (_)_ _ ___ | \ _ _(_)_ _____ _ _ ++ * | |\/| / _` / _| ' \| | ' \/ -_) | |) | '_| \ V / -_) '_| ++ * |_| |_\__,_\__|_||_|_|_||_\___| |___/|_| |_|\_/\___|_| ++ * ++ */ ++ ++static int tas5713_hw_params(struct snd_pcm_substream *substream, ++ struct snd_pcm_hw_params *params, ++ struct snd_soc_dai *dai) ++{ ++ u16 blen = 0x00; ++ ++ struct snd_soc_component *component = dai->component; ++ priv_data->component = component; ++ ++ switch (params_format(params)) { ++ case SNDRV_PCM_FORMAT_S16_LE: ++ blen = 0x03; ++ break; ++ case SNDRV_PCM_FORMAT_S20_3LE: ++ blen = 0x1; ++ break; ++ case SNDRV_PCM_FORMAT_S24_LE: ++ blen = 0x04; ++ break; ++ case SNDRV_PCM_FORMAT_S32_LE: ++ blen = 0x05; ++ break; ++ default: ++ dev_err(dai->dev, "Unsupported word length: %u\n", ++ params_format(params)); ++ return -EINVAL; ++ } ++ ++ // set word length ++ snd_soc_component_update_bits(component, TAS5713_SERIAL_DATA_INTERFACE, 0x7, blen); ++ ++ return 0; ++} ++ ++ ++static int tas5713_mute_stream(struct snd_soc_dai *dai, int mute, int stream) ++{ ++ unsigned int val = 0; ++ ++ struct tas5713_priv *tas5713; ++ struct snd_soc_component *component = dai->component; ++ tas5713 = snd_soc_component_get_drvdata(component); ++ ++ if (mute) { ++ val = TAS5713_SOFT_MUTE_ALL; ++ } ++ ++ return regmap_write(tas5713->regmap, TAS5713_SOFT_MUTE, val); ++} ++ ++ ++static const struct snd_soc_dai_ops tas5713_dai_ops = { ++ .hw_params = tas5713_hw_params, ++ .mute_stream = tas5713_mute_stream, ++}; ++ ++ ++static struct snd_soc_dai_driver tas5713_dai = { ++ .name = "tas5713-hifi", ++ .playback = { ++ .stream_name = "Playback", ++ .channels_min = 2, ++ .channels_max = 2, ++ .rates = SNDRV_PCM_RATE_8000_48000, ++ .formats = (SNDRV_PCM_FMTBIT_S16_LE | SNDRV_PCM_FMTBIT_S24_LE | SNDRV_PCM_FMTBIT_S32_LE ), ++ }, ++ .ops = &tas5713_dai_ops, ++}; ++ ++ ++ ++ ++/* ++ * ___ _ ___ _ ++ * / __|___ __| |___ __ | \ _ _(_)_ _____ _ _ ++ * | (__/ _ \/ _` / -_) _| | |) | '_| \ V / -_) '_| ++ * \___\___/\__,_\___\__| |___/|_| |_|\_/\___|_| ++ * ++ */ ++ ++static void tas5713_remove(struct snd_soc_component *component) ++{ ++ struct tas5713_priv *tas5713; ++ ++ tas5713 = snd_soc_component_get_drvdata(component); ++} ++ ++ ++static int tas5713_probe(struct snd_soc_component *component) ++{ ++ struct tas5713_priv *tas5713; ++ int i, ret; ++ ++ i2c = container_of(component->dev, struct i2c_client, dev); ++ ++ tas5713 = snd_soc_component_get_drvdata(component); ++ ++ // Reset error ++ ret = snd_soc_component_write(component, TAS5713_ERROR_STATUS, 0x00); ++ if (ret < 0) return ret; ++ ++ // Trim oscillator ++ ret = snd_soc_component_write(component, TAS5713_OSC_TRIM, 0x00); ++ if (ret < 0) return ret; ++ msleep(1000); ++ ++ // Reset error ++ ret = snd_soc_component_write(component, TAS5713_ERROR_STATUS, 0x00); ++ if (ret < 0) return ret; ++ ++ // I2S 24bit ++ ret = snd_soc_component_write(component, TAS5713_SERIAL_DATA_INTERFACE, 0x05); ++ if (ret < 0) return ret; ++ ++ // Unmute ++ ret = snd_soc_component_write(component, TAS5713_SYSTEM_CTRL2, 0x00); ++ if (ret < 0) return ret; ++ ret = snd_soc_component_write(component, TAS5713_SOFT_MUTE, 0x00); ++ if (ret < 0) return ret; ++ ++ // Set volume to 0db ++ ret = snd_soc_component_write(component, TAS5713_VOL_MASTER, 0x00); ++ if (ret < 0) return ret; ++ ++ // Now start programming the default initialization sequence ++ for (i = 0; i < ARRAY_SIZE(tas5713_init_sequence); ++i) { ++ ret = i2c_master_send(i2c, ++ tas5713_init_sequence[i].data, ++ tas5713_init_sequence[i].size); ++ if (ret < 0) { ++ printk(KERN_INFO "TAS5713 CODEC PROBE: InitSeq returns: %d\n", ret); ++ } ++ } ++ ++ // Unmute ++ ret = snd_soc_component_write(component, TAS5713_SYSTEM_CTRL2, 0x00); ++ if (ret < 0) return ret; ++ ++ return 0; ++} ++ ++ ++static struct snd_soc_component_driver soc_codec_dev_tas5713 = { ++ .probe = tas5713_probe, ++ .remove = tas5713_remove, ++ .controls = tas5713_snd_controls, ++ .num_controls = ARRAY_SIZE(tas5713_snd_controls), ++}; ++ ++ ++ ++ ++/* ++ * ___ ___ ___ ___ _ ++ * |_ _|_ ) __| | \ _ _(_)_ _____ _ _ ++ * | | / / (__ | |) | '_| \ V / -_) '_| ++ * |___/___\___| |___/|_| |_|\_/\___|_| ++ * ++ */ ++ ++static const struct reg_default tas5713_reg_defaults[] = { ++ { 0x07 ,0x80 }, // R7 - VOL_MASTER - -40dB ++ { 0x08 , 30 }, // R8 - VOL_CH1 - 0dB ++ { 0x09 , 30 }, // R9 - VOL_CH2 - 0dB ++ { 0x0A ,0x80 }, // R10 - VOL_HEADPHONE - -40dB ++}; ++ ++ ++static bool tas5713_reg_volatile(struct device *dev, unsigned int reg) ++{ ++ switch (reg) { ++ case TAS5713_DEVICE_ID: ++ case TAS5713_ERROR_STATUS: ++ case TAS5713_CLOCK_CTRL: ++ return true; ++ default: ++ return false; ++ } ++} ++ ++ ++static const struct of_device_id tas5713_of_match[] = { ++ { .compatible = "ti,tas5713", }, ++ { } ++}; ++MODULE_DEVICE_TABLE(of, tas5713_of_match); ++ ++ ++static struct regmap_config tas5713_regmap_config = { ++ .reg_bits = 8, ++ .val_bits = 8, ++ ++ .max_register = TAS5713_MAX_REGISTER, ++ .volatile_reg = tas5713_reg_volatile, ++ ++ .cache_type = REGCACHE_RBTREE, ++ .reg_defaults = tas5713_reg_defaults, ++ .num_reg_defaults = ARRAY_SIZE(tas5713_reg_defaults), ++}; ++ ++ ++static int tas5713_i2c_probe(struct i2c_client *i2c, ++ const struct i2c_device_id *id) ++{ ++ int ret; ++ ++ priv_data = devm_kzalloc(&i2c->dev, sizeof *priv_data, GFP_KERNEL); ++ if (!priv_data) ++ return -ENOMEM; ++ ++ priv_data->regmap = devm_regmap_init_i2c(i2c, &tas5713_regmap_config); ++ if (IS_ERR(priv_data->regmap)) { ++ ret = PTR_ERR(priv_data->regmap); ++ return ret; ++ } ++ ++ i2c_set_clientdata(i2c, priv_data); ++ ++ ret = snd_soc_register_component(&i2c->dev, ++ &soc_codec_dev_tas5713, &tas5713_dai, 1); ++ ++ return ret; ++} ++ ++ ++static int tas5713_i2c_remove(struct i2c_client *i2c) ++{ ++ snd_soc_unregister_component(&i2c->dev); ++ i2c_set_clientdata(i2c, NULL); ++ ++ kfree(priv_data); ++ ++ return 0; ++} ++ ++ ++static const struct i2c_device_id tas5713_i2c_id[] = { ++ { "tas5713", 0 }, ++ { } ++}; ++ ++MODULE_DEVICE_TABLE(i2c, tas5713_i2c_id); ++ ++ ++static struct i2c_driver tas5713_i2c_driver = { ++ .driver = { ++ .name = "tas5713", ++ .owner = THIS_MODULE, ++ .of_match_table = tas5713_of_match, ++ }, ++ .probe = tas5713_i2c_probe, ++ .remove = tas5713_i2c_remove, ++ .id_table = tas5713_i2c_id ++}; ++ ++ ++static int __init tas5713_modinit(void) ++{ ++ int ret = 0; ++ ++ ret = i2c_add_driver(&tas5713_i2c_driver); ++ if (ret) { ++ printk(KERN_ERR "Failed to register tas5713 I2C driver: %d\n", ++ ret); ++ } ++ ++ return ret; ++} ++module_init(tas5713_modinit); ++ ++ ++static void __exit tas5713_exit(void) ++{ ++ i2c_del_driver(&tas5713_i2c_driver); ++} ++module_exit(tas5713_exit); ++ ++ ++MODULE_AUTHOR("Sebastian Eickhoff "); ++MODULE_DESCRIPTION("ASoC driver for TAS5713"); ++MODULE_LICENSE("GPL v2"); +--- /dev/null ++++ b/sound/soc/codecs/tas5713.h +@@ -0,0 +1,210 @@ ++/* ++ * ASoC Driver for TAS5713 ++ * ++ * Author: Sebastian Eickhoff ++ * Copyright 2014 ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * version 2 as published by the Free Software Foundation. ++ * ++ * This program is distributed in the hope that it will be useful, but ++ * WITHOUT ANY WARRANTY; without even the implied warranty of ++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU ++ * General Public License for more details. ++ */ ++ ++#ifndef _TAS5713_H ++#define _TAS5713_H ++ ++ ++// TAS5713 I2C-bus register addresses ++ ++#define TAS5713_CLOCK_CTRL 0x00 ++#define TAS5713_DEVICE_ID 0x01 ++#define TAS5713_ERROR_STATUS 0x02 ++#define TAS5713_SYSTEM_CTRL1 0x03 ++#define TAS5713_SERIAL_DATA_INTERFACE 0x04 ++#define TAS5713_SYSTEM_CTRL2 0x05 ++#define TAS5713_SOFT_MUTE 0x06 ++#define TAS5713_VOL_MASTER 0x07 ++#define TAS5713_VOL_CH1 0x08 ++#define TAS5713_VOL_CH2 0x09 ++#define TAS5713_VOL_HEADPHONE 0x0A ++#define TAS5713_VOL_CONFIG 0x0E ++#define TAS5713_MODULATION_LIMIT 0x10 ++#define TAS5713_IC_DLY_CH1 0x11 ++#define TAS5713_IC_DLY_CH2 0x12 ++#define TAS5713_IC_DLY_CH3 0x13 ++#define TAS5713_IC_DLY_CH4 0x14 ++ ++#define TAS5713_START_STOP_PERIOD 0x1A ++#define TAS5713_OSC_TRIM 0x1B ++#define TAS5713_BKND_ERR 0x1C ++ ++#define TAS5713_INPUT_MUX 0x20 ++#define TAS5713_SRC_SELECT_CH4 0x21 ++#define TAS5713_PWM_MUX 0x25 ++ ++#define TAS5713_CH1_BQ0 0x29 ++#define TAS5713_CH1_BQ1 0x2A ++#define TAS5713_CH1_BQ2 0x2B ++#define TAS5713_CH1_BQ3 0x2C ++#define TAS5713_CH1_BQ4 0x2D ++#define TAS5713_CH1_BQ5 0x2E ++#define TAS5713_CH1_BQ6 0x2F ++#define TAS5713_CH1_BQ7 0x58 ++#define TAS5713_CH1_BQ8 0x59 ++ ++#define TAS5713_CH2_BQ0 0x30 ++#define TAS5713_CH2_BQ1 0x31 ++#define TAS5713_CH2_BQ2 0x32 ++#define TAS5713_CH2_BQ3 0x33 ++#define TAS5713_CH2_BQ4 0x34 ++#define TAS5713_CH2_BQ5 0x35 ++#define TAS5713_CH2_BQ6 0x36 ++#define TAS5713_CH2_BQ7 0x5C ++#define TAS5713_CH2_BQ8 0x5D ++ ++#define TAS5713_CH4_BQ0 0x5A ++#define TAS5713_CH4_BQ1 0x5B ++#define TAS5713_CH3_BQ0 0x5E ++#define TAS5713_CH3_BQ1 0x5F ++ ++#define TAS5713_DRC1_SOFTENING_FILTER_ALPHA_OMEGA 0x3B ++#define TAS5713_DRC1_ATTACK_RELEASE_RATE 0x3C ++#define TAS5713_DRC2_SOFTENING_FILTER_ALPHA_OMEGA 0x3E ++#define TAS5713_DRC2_ATTACK_RELEASE_RATE 0x3F ++#define TAS5713_DRC1_ATTACK_RELEASE_THRES 0x40 ++#define TAS5713_DRC2_ATTACK_RELEASE_THRES 0x43 ++#define TAS5713_DRC_CTRL 0x46 ++ ++#define TAS5713_BANK_SW_CTRL 0x50 ++#define TAS5713_CH1_OUTPUT_MIXER 0x51 ++#define TAS5713_CH2_OUTPUT_MIXER 0x52 ++#define TAS5713_CH1_INPUT_MIXER 0x53 ++#define TAS5713_CH2_INPUT_MIXER 0x54 ++#define TAS5713_OUTPUT_POST_SCALE 0x56 ++#define TAS5713_OUTPUT_PRESCALE 0x57 ++ ++#define TAS5713_IDF_POST_SCALE 0x62 ++ ++#define TAS5713_CH1_INLINE_MIXER 0x70 ++#define TAS5713_CH1_INLINE_DRC_EN_MIXER 0x71 ++#define TAS5713_CH1_R_CHANNEL_MIXER 0x72 ++#define TAS5713_CH1_L_CHANNEL_MIXER 0x73 ++#define TAS5713_CH2_INLINE_MIXER 0x74 ++#define TAS5713_CH2_INLINE_DRC_EN_MIXER 0x75 ++#define TAS5713_CH2_L_CHANNEL_MIXER 0x76 ++#define TAS5713_CH2_R_CHANNEL_MIXER 0x77 ++ ++#define TAS5713_UPDATE_DEV_ADDR_KEY 0xF8 ++#define TAS5713_UPDATE_DEV_ADDR_REG 0xF9 ++ ++#define TAS5713_REGISTER_COUNT 0x46 ++#define TAS5713_MAX_REGISTER 0xF9 ++ ++ ++// Bitmasks for registers ++#define TAS5713_SOFT_MUTE_ALL 0x07 ++ ++ ++ ++struct tas5713_init_command { ++ const int size; ++ const char *const data; ++}; ++ ++static const struct tas5713_init_command tas5713_init_sequence[] = { ++ ++ // Trim oscillator ++ { .size = 2, .data = "\x1B\x00" }, ++ // System control register 1 (0x03): block DC ++ { .size = 2, .data = "\x03\x80" }, ++ // Mute everything ++ { .size = 2, .data = "\x05\x40" }, ++ // Modulation limit register (0x10): 97.7% ++ { .size = 2, .data = "\x10\x02" }, ++ // Interchannel delay registers ++ // (0x11, 0x12, 0x13, and 0x14): BD mode ++ { .size = 2, .data = "\x11\xB8" }, ++ { .size = 2, .data = "\x12\x60" }, ++ { .size = 2, .data = "\x13\xA0" }, ++ { .size = 2, .data = "\x14\x48" }, ++ // PWM shutdown group register (0x19): no shutdown ++ { .size = 2, .data = "\x19\x00" }, ++ // Input multiplexer register (0x20): BD mode ++ { .size = 2, .data = "\x20\x00\x89\x77\x72" }, ++ // PWM output mux register (0x25) ++ // Channel 1 --> OUTA, channel 1 neg --> OUTB ++ // Channel 2 --> OUTC, channel 2 neg --> OUTD ++ { .size = 5, .data = "\x25\x01\x02\x13\x45" }, ++ // DRC control (0x46): DRC off ++ { .size = 5, .data = "\x46\x00\x00\x00\x00" }, ++ // BKND_ERR register (0x1C): 299ms reset period ++ { .size = 2, .data = "\x1C\x07" }, ++ // Mute channel 3 ++ { .size = 2, .data = "\x0A\xFF" }, ++ // Volume configuration register (0x0E): volume slew 512 steps ++ { .size = 2, .data = "\x0E\x90" }, ++ // Clock control register (0x00): 44/48kHz, MCLK=64xfs ++ { .size = 2, .data = "\x00\x60" }, ++ // Bank switch and eq control (0x50): no bank switching ++ { .size = 5, .data = "\x50\x00\x00\x00\x00" }, ++ // Volume registers (0x07, 0x08, 0x09, 0x0A) ++ { .size = 2, .data = "\x07\x20" }, ++ { .size = 2, .data = "\x08\x30" }, ++ { .size = 2, .data = "\x09\x30" }, ++ { .size = 2, .data = "\x0A\xFF" }, ++ // 0x72, 0x73, 0x76, 0x77 input mixer: ++ // no intermix between channels ++ { .size = 5, .data = "\x72\x00\x00\x00\x00" }, ++ { .size = 5, .data = "\x73\x00\x80\x00\x00" }, ++ { .size = 5, .data = "\x76\x00\x00\x00\x00" }, ++ { .size = 5, .data = "\x77\x00\x80\x00\x00" }, ++ // 0x70, 0x71, 0x74, 0x75 inline DRC mixer: ++ // no inline DRC inmix ++ { .size = 5, .data = "\x70\x00\x80\x00\x00" }, ++ { .size = 5, .data = "\x71\x00\x00\x00\x00" }, ++ { .size = 5, .data = "\x74\x00\x80\x00\x00" }, ++ { .size = 5, .data = "\x75\x00\x00\x00\x00" }, ++ // 0x56, 0x57 Output scale ++ { .size = 5, .data = "\x56\x00\x80\x00\x00" }, ++ { .size = 5, .data = "\x57\x00\x02\x00\x00" }, ++ // 0x3B, 0x3c ++ { .size = 9, .data = "\x3B\x00\x08\x00\x00\x00\x78\x00\x00" }, ++ { .size = 9, .data = "\x3C\x00\x00\x01\x00\xFF\xFF\xFF\x00" }, ++ { .size = 9, .data = "\x3E\x00\x08\x00\x00\x00\x78\x00\x00" }, ++ { .size = 9, .data = "\x3F\x00\x00\x01\x00\xFF\xFF\xFF\x00" }, ++ { .size = 9, .data = "\x40\x00\x00\x01\x00\xFF\xFF\xFF\x00" }, ++ { .size = 9, .data = "\x43\x00\x00\x01\x00\xFF\xFF\xFF\x00" }, ++ // 0x51, 0x52: output mixer ++ { .size = 9, .data = "\x51\x00\x80\x00\x00\x00\x00\x00\x00" }, ++ { .size = 9, .data = "\x52\x00\x80\x00\x00\x00\x00\x00\x00" }, ++ // PEQ defaults ++ { .size = 21, .data = "\x29\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x2A\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x2B\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x2C\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x2D\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x2E\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x2F\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x30\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x31\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x32\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x33\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x34\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x35\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x36\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x58\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x59\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x5C\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x5D\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x5E\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x5F\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x5A\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++ { .size = 21, .data = "\x5B\x00\x80\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00" }, ++}; ++ ++ ++#endif /* _TAS5713_H */ +--- a/sound/soc/soc-core.c ++++ b/sound/soc/soc-core.c +@@ -1429,7 +1429,15 @@ int snd_soc_runtime_set_dai_fmt(struct s + int ret; + + for_each_rtd_codec_dais(rtd, i, codec_dai) { +- ret = snd_soc_dai_set_fmt(codec_dai, dai_fmt); ++ unsigned int codec_dai_fmt = dai_fmt; ++ ++ // there can only be one master when using multiple codecs ++ if (i && (codec_dai_fmt & SND_SOC_DAIFMT_MASTER_MASK)) { ++ codec_dai_fmt &= ~SND_SOC_DAIFMT_MASTER_MASK; ++ codec_dai_fmt |= SND_SOC_DAIFMT_CBS_CFS; ++ } ++ ++ ret = snd_soc_dai_set_fmt(codec_dai, codec_dai_fmt); + if (ret != 0 && ret != -ENOTSUPP) { + dev_warn(codec_dai->dev, + "ASoC: Failed to set DAI format: %d\n", ret); diff --git a/target/linux/bcm27xx/patches-5.10/950-0061-Fixes-a-problem-when-module-probes-before-i2c-module.patch b/target/linux/bcm27xx/patches-5.10/950-0061-Fixes-a-problem-when-module-probes-before-i2c-module.patch new file mode 100644 index 0000000000..f4dc7b6289 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0061-Fixes-a-problem-when-module-probes-before-i2c-module.patch @@ -0,0 +1,46 @@ +From 4be98b29d123fc7615ea8404fbda450ec8acb084 Mon Sep 17 00:00:00 2001 +From: Joerg Schambacher +Date: Fri, 16 Oct 2020 15:17:07 +0200 +Subject: [PATCH] Fixes a problem when module probes before i2c module + is available + +The driver crashed while a NULL pointer returned by i2c_get_adapter() +has been used to access the i2c bus functions. +The headphone probing function hb_hp_probe() now returns -EPROBE_DEFER +in case the i2c module has not been loaded yet. + +Signed-off-by: Joerg Schambacher +--- + sound/soc/bcm/hifiberry_dacplus.c | 9 +++++++-- + 1 file changed, 7 insertions(+), 2 deletions(-) + +--- a/sound/soc/bcm/hifiberry_dacplus.c ++++ b/sound/soc/bcm/hifiberry_dacplus.c +@@ -315,12 +315,14 @@ static int hb_hp_detect(void) + { + struct i2c_adapter *adap = i2c_get_adapter(1); + int ret; +- + struct i2c_client tpa_i2c_client = { + .addr = 0x60, + .adapter = adap, + }; + ++ if (!adap) ++ return -EPROBE_DEFER; /* I2C module not yet available */ ++ + ret = i2c_smbus_read_byte(&tpa_i2c_client) >= 0; + i2c_put_adapter(adap); + return ret; +@@ -342,7 +344,10 @@ static int snd_rpi_hifiberry_dacplus_pro + struct of_changeset ocs; + + /* probe for head phone amp */ +- if (hb_hp_detect()) { ++ ret = hb_hp_detect(); ++ if (ret < 0) ++ return ret; ++ if (ret) { + card->aux_dev = hifiberry_dacplus_aux_devs; + card->num_aux_devs = + ARRAY_SIZE(hifiberry_dacplus_aux_devs); diff --git a/target/linux/bcm27xx/patches-5.10/950-0062-rpi_display-add-backlight-driver-and-overlay.patch b/target/linux/bcm27xx/patches-5.10/950-0062-rpi_display-add-backlight-driver-and-overlay.patch new file mode 100644 index 0000000000..151e9e9b7e --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0062-rpi_display-add-backlight-driver-and-overlay.patch @@ -0,0 +1,172 @@ +From 3bbdfc9493655ea9ff7e3c8eeee85f28b0f84369 Mon Sep 17 00:00:00 2001 +From: P33M +Date: Wed, 21 Oct 2015 14:55:21 +0100 +Subject: [PATCH] rpi_display: add backlight driver and overlay + +Add a mailbox-driven backlight controller for the Raspberry Pi DSI +touchscreen display. Requires updated GPU firmware to recognise the +mailbox request. + +Signed-off-by: Gordon Hollingworth + +Add Raspberry Pi firmware driver to the dependencies of backlight driver + +Otherwise the backlight driver fails to build if the firmware +loading driver is not in the kernel + +Signed-off-by: Alex Riesen +--- + drivers/video/backlight/Kconfig | 7 ++ + drivers/video/backlight/Makefile | 1 + + drivers/video/backlight/rpi_backlight.c | 119 ++++++++++++++++++++++++ + 3 files changed, 127 insertions(+) + create mode 100644 drivers/video/backlight/rpi_backlight.c + +--- a/drivers/video/backlight/Kconfig ++++ b/drivers/video/backlight/Kconfig +@@ -248,6 +248,13 @@ config BACKLIGHT_PWM + If you have a LCD backlight adjustable by PWM, say Y to enable + this driver. + ++config BACKLIGHT_RPI ++ tristate "Raspberry Pi display firmware driven backlight" ++ depends on RASPBERRYPI_FIRMWARE ++ help ++ If you have the Raspberry Pi DSI touchscreen display, say Y to ++ enable the mailbox-controlled backlight driver. ++ + config BACKLIGHT_DA903X + tristate "Backlight Driver for DA9030/DA9034 using WLED" + depends on PMIC_DA903X +--- a/drivers/video/backlight/Makefile ++++ b/drivers/video/backlight/Makefile +@@ -49,6 +49,7 @@ obj-$(CONFIG_BACKLIGHT_PANDORA) += pand + obj-$(CONFIG_BACKLIGHT_PCF50633) += pcf50633-backlight.o + obj-$(CONFIG_BACKLIGHT_PWM) += pwm_bl.o + obj-$(CONFIG_BACKLIGHT_QCOM_WLED) += qcom-wled.o ++obj-$(CONFIG_BACKLIGHT_RPI) += rpi_backlight.o + obj-$(CONFIG_BACKLIGHT_SAHARA) += kb3886_bl.o + obj-$(CONFIG_BACKLIGHT_SKY81452) += sky81452-backlight.o + obj-$(CONFIG_BACKLIGHT_TOSA) += tosa_bl.o +--- /dev/null ++++ b/drivers/video/backlight/rpi_backlight.c +@@ -0,0 +1,119 @@ ++/* ++ * rpi_bl.c - Backlight controller through VPU ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++struct rpi_backlight { ++ struct device *dev; ++ struct device *fbdev; ++ struct rpi_firmware *fw; ++}; ++ ++static int rpi_backlight_update_status(struct backlight_device *bl) ++{ ++ struct rpi_backlight *gbl = bl_get_data(bl); ++ int brightness = bl->props.brightness; ++ int ret; ++ ++ if (bl->props.power != FB_BLANK_UNBLANK || ++ bl->props.fb_blank != FB_BLANK_UNBLANK || ++ bl->props.state & (BL_CORE_SUSPENDED | BL_CORE_FBBLANK)) ++ brightness = 0; ++ ++ ret = rpi_firmware_property(gbl->fw, ++ RPI_FIRMWARE_FRAMEBUFFER_SET_BACKLIGHT, ++ &brightness, sizeof(brightness)); ++ if (ret) { ++ dev_err(gbl->dev, "Failed to set brightness\n"); ++ return ret; ++ } ++ ++ if (brightness < 0) { ++ dev_err(gbl->dev, "Backlight change failed\n"); ++ return -EAGAIN; ++ } ++ ++ return 0; ++} ++ ++static const struct backlight_ops rpi_backlight_ops = { ++ .options = BL_CORE_SUSPENDRESUME, ++ .update_status = rpi_backlight_update_status, ++}; ++ ++static int rpi_backlight_probe(struct platform_device *pdev) ++{ ++ struct backlight_properties props; ++ struct backlight_device *bl; ++ struct rpi_backlight *gbl; ++ struct device_node *fw_node; ++ ++ gbl = devm_kzalloc(&pdev->dev, sizeof(*gbl), GFP_KERNEL); ++ if (gbl == NULL) ++ return -ENOMEM; ++ ++ gbl->dev = &pdev->dev; ++ ++ fw_node = of_parse_phandle(pdev->dev.of_node, "firmware", 0); ++ if (!fw_node) { ++ dev_err(&pdev->dev, "Missing firmware node\n"); ++ return -ENOENT; ++ } ++ ++ gbl->fw = rpi_firmware_get(fw_node); ++ if (!gbl->fw) ++ return -EPROBE_DEFER; ++ ++ memset(&props, 0, sizeof(props)); ++ props.type = BACKLIGHT_RAW; ++ props.max_brightness = 255; ++ bl = devm_backlight_device_register(&pdev->dev, dev_name(&pdev->dev), ++ &pdev->dev, gbl, &rpi_backlight_ops, ++ &props); ++ if (IS_ERR(bl)) { ++ dev_err(&pdev->dev, "failed to register backlight\n"); ++ return PTR_ERR(bl); ++ } ++ ++ bl->props.brightness = 255; ++ backlight_update_status(bl); ++ ++ platform_set_drvdata(pdev, bl); ++ return 0; ++} ++ ++static const struct of_device_id rpi_backlight_of_match[] = { ++ { .compatible = "raspberrypi,rpi-backlight" }, ++ { /* sentinel */ } ++}; ++MODULE_DEVICE_TABLE(of, rpi_backlight_of_match); ++ ++static struct platform_driver rpi_backlight_driver = { ++ .driver = { ++ .name = "rpi-backlight", ++ .of_match_table = of_match_ptr(rpi_backlight_of_match), ++ }, ++ .probe = rpi_backlight_probe, ++}; ++ ++module_platform_driver(rpi_backlight_driver); ++ ++MODULE_AUTHOR("Gordon Hollingworth "); ++MODULE_DESCRIPTION("Raspberry Pi mailbox based Backlight Driver"); ++MODULE_LICENSE("GPL"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0063-bcm2835-virtgpio-Virtual-GPIO-driver.patch b/target/linux/bcm27xx/patches-5.10/950-0063-bcm2835-virtgpio-Virtual-GPIO-driver.patch new file mode 100644 index 0000000000..1d02e42a1d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0063-bcm2835-virtgpio-Virtual-GPIO-driver.patch @@ -0,0 +1,256 @@ +From f82deda879262289568dec22dd43ecc10c265fb6 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Tue, 23 Feb 2016 19:56:04 +0000 +Subject: [PATCH] bcm2835-virtgpio: Virtual GPIO driver + +Add a virtual GPIO driver that uses the firmware mailbox interface to +request that the VPU toggles LEDs. +--- + drivers/gpio/Kconfig | 6 + + drivers/gpio/Makefile | 1 + + drivers/gpio/gpio-bcm-virt.c | 214 +++++++++++++++++++++++++++++++++++ + 3 files changed, 221 insertions(+) + create mode 100644 drivers/gpio/gpio-bcm-virt.c + +--- a/drivers/gpio/Kconfig ++++ b/drivers/gpio/Kconfig +@@ -193,6 +193,12 @@ config GPIO_BCM_XGS_IPROC + help + Say yes here to enable GPIO support for Broadcom XGS iProc SoCs. + ++config GPIO_BCM_VIRT ++ bool "Broadcom Virt GPIO" ++ depends on OF_GPIO && RASPBERRYPI_FIRMWARE && (ARCH_BCM2835 || COMPILE_TEST) ++ help ++ Turn on virtual GPIO support for Broadcom BCM283X chips. ++ + config GPIO_BRCMSTB + tristate "BRCMSTB GPIO support" + default y if (ARCH_BRCMSTB || BMIPS_GENERIC) +--- a/drivers/gpio/Makefile ++++ b/drivers/gpio/Makefile +@@ -38,6 +38,7 @@ obj-$(CONFIG_GPIO_ASPEED_SGPIO) += gpio + obj-$(CONFIG_GPIO_ATH79) += gpio-ath79.o + obj-$(CONFIG_GPIO_BCM_KONA) += gpio-bcm-kona.o + obj-$(CONFIG_GPIO_BCM_XGS_IPROC) += gpio-xgs-iproc.o ++obj-$(CONFIG_GPIO_BCM_VIRT) += gpio-bcm-virt.o + obj-$(CONFIG_GPIO_BD70528) += gpio-bd70528.o + obj-$(CONFIG_GPIO_BD71828) += gpio-bd71828.o + obj-$(CONFIG_GPIO_BD9571MWV) += gpio-bd9571mwv.o +--- /dev/null ++++ b/drivers/gpio/gpio-bcm-virt.c +@@ -0,0 +1,214 @@ ++/* ++ * brcmvirt GPIO driver ++ * ++ * Copyright (C) 2012,2013 Dom Cobley ++ * Based on gpio-clps711x.c by Alexander Shiyan ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License as published by ++ * the Free Software Foundation; either version 2 of the License, or ++ * (at your option) any later version. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define MODULE_NAME "brcmvirt-gpio" ++#define NUM_GPIO 2 ++ ++struct brcmvirt_gpio { ++ struct gpio_chip gc; ++ u32 __iomem *ts_base; ++ /* two packed 16-bit counts of enabled and disables ++ Allows host to detect a brief enable that was missed */ ++ u32 enables_disables[NUM_GPIO]; ++ dma_addr_t bus_addr; ++}; ++ ++static int brcmvirt_gpio_dir_in(struct gpio_chip *gc, unsigned off) ++{ ++ struct brcmvirt_gpio *gpio; ++ gpio = container_of(gc, struct brcmvirt_gpio, gc); ++ return -EINVAL; ++} ++ ++static int brcmvirt_gpio_dir_out(struct gpio_chip *gc, unsigned off, int val) ++{ ++ struct brcmvirt_gpio *gpio; ++ gpio = container_of(gc, struct brcmvirt_gpio, gc); ++ return 0; ++} ++ ++static int brcmvirt_gpio_get(struct gpio_chip *gc, unsigned off) ++{ ++ struct brcmvirt_gpio *gpio; ++ unsigned v; ++ gpio = container_of(gc, struct brcmvirt_gpio, gc); ++ v = readl(gpio->ts_base + off); ++ return (v >> off) & 1; ++} ++ ++static void brcmvirt_gpio_set(struct gpio_chip *gc, unsigned off, int val) ++{ ++ struct brcmvirt_gpio *gpio; ++ u16 enables, disables; ++ s16 diff; ++ bool lit; ++ gpio = container_of(gc, struct brcmvirt_gpio, gc); ++ enables = gpio->enables_disables[off] >> 16; ++ disables = gpio->enables_disables[off] >> 0; ++ diff = (s16)(enables - disables); ++ lit = diff > 0; ++ if ((val && lit) || (!val && !lit)) ++ return; ++ if (val) ++ enables++; ++ else ++ disables++; ++ diff = (s16)(enables - disables); ++ BUG_ON(diff != 0 && diff != 1); ++ gpio->enables_disables[off] = (enables << 16) | (disables << 0); ++ writel(gpio->enables_disables[off], gpio->ts_base + off); ++} ++ ++static int brcmvirt_gpio_probe(struct platform_device *pdev) ++{ ++ int err = 0; ++ struct device *dev = &pdev->dev; ++ struct device_node *np = dev->of_node; ++ struct device_node *fw_node; ++ struct rpi_firmware *fw; ++ struct brcmvirt_gpio *ucb; ++ u32 gpiovirtbuf; ++ ++ fw_node = of_parse_phandle(np, "firmware", 0); ++ if (!fw_node) { ++ dev_err(dev, "Missing firmware node\n"); ++ return -ENOENT; ++ } ++ ++ fw = rpi_firmware_get(fw_node); ++ if (!fw) ++ return -EPROBE_DEFER; ++ ++ ucb = devm_kzalloc(dev, sizeof *ucb, GFP_KERNEL); ++ if (!ucb) { ++ err = -EINVAL; ++ goto out; ++ } ++ ++ ucb->ts_base = dma_alloc_coherent(dev, PAGE_SIZE, &ucb->bus_addr, GFP_KERNEL); ++ if (!ucb->ts_base) { ++ pr_err("[%s]: failed to dma_alloc_coherent(%ld)\n", ++ __func__, PAGE_SIZE); ++ err = -ENOMEM; ++ goto out; ++ } ++ ++ gpiovirtbuf = (u32)ucb->bus_addr; ++ err = rpi_firmware_property(fw, RPI_FIRMWARE_FRAMEBUFFER_SET_GPIOVIRTBUF, ++ &gpiovirtbuf, sizeof(gpiovirtbuf)); ++ ++ if (err || gpiovirtbuf != 0) { ++ dev_warn(dev, "Failed to set gpiovirtbuf, trying to get err:%x\n", err); ++ dma_free_coherent(dev, PAGE_SIZE, ucb->ts_base, ucb->bus_addr); ++ ucb->ts_base = 0; ++ ucb->bus_addr = 0; ++ } ++ ++ if (!ucb->ts_base) { ++ err = rpi_firmware_property(fw, RPI_FIRMWARE_FRAMEBUFFER_GET_GPIOVIRTBUF, ++ &gpiovirtbuf, sizeof(gpiovirtbuf)); ++ ++ if (err) { ++ dev_err(dev, "Failed to get gpiovirtbuf\n"); ++ goto out; ++ } ++ ++ if (!gpiovirtbuf) { ++ dev_err(dev, "No virtgpio buffer\n"); ++ err = -ENOENT; ++ goto out; ++ } ++ ++ // mmap the physical memory ++ gpiovirtbuf &= ~0xc0000000; ++ ucb->ts_base = ioremap(gpiovirtbuf, 4096); ++ if (ucb->ts_base == NULL) { ++ dev_err(dev, "Failed to map physical address\n"); ++ err = -ENOENT; ++ goto out; ++ } ++ ucb->bus_addr = 0; ++ } ++ ucb->gc.label = MODULE_NAME; ++ ucb->gc.owner = THIS_MODULE; ++ //ucb->gc.dev = dev; ++ ucb->gc.of_node = np; ++ ucb->gc.base = 100; ++ ucb->gc.ngpio = NUM_GPIO; ++ ++ ucb->gc.direction_input = brcmvirt_gpio_dir_in; ++ ucb->gc.direction_output = brcmvirt_gpio_dir_out; ++ ucb->gc.get = brcmvirt_gpio_get; ++ ucb->gc.set = brcmvirt_gpio_set; ++ ucb->gc.can_sleep = true; ++ ++ err = gpiochip_add(&ucb->gc); ++ if (err) ++ goto out; ++ ++ platform_set_drvdata(pdev, ucb); ++ ++ return 0; ++out: ++ if (ucb->bus_addr) { ++ dma_free_coherent(dev, PAGE_SIZE, ucb->ts_base, ucb->bus_addr); ++ ucb->bus_addr = 0; ++ ucb->ts_base = NULL; ++ } else if (ucb->ts_base) { ++ iounmap(ucb->ts_base); ++ ucb->ts_base = NULL; ++ } ++ return err; ++} ++ ++static int brcmvirt_gpio_remove(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ int err = 0; ++ struct brcmvirt_gpio *ucb = platform_get_drvdata(pdev); ++ ++ gpiochip_remove(&ucb->gc); ++ if (ucb->bus_addr) ++ dma_free_coherent(dev, PAGE_SIZE, ucb->ts_base, ucb->bus_addr); ++ else if (ucb->ts_base) ++ iounmap(ucb->ts_base); ++ return err; ++} ++ ++static const struct of_device_id __maybe_unused brcmvirt_gpio_ids[] = { ++ { .compatible = "brcm,bcm2835-virtgpio" }, ++ { } ++}; ++MODULE_DEVICE_TABLE(of, brcmvirt_gpio_ids); ++ ++static struct platform_driver brcmvirt_gpio_driver = { ++ .driver = { ++ .name = MODULE_NAME, ++ .owner = THIS_MODULE, ++ .of_match_table = of_match_ptr(brcmvirt_gpio_ids), ++ }, ++ .probe = brcmvirt_gpio_probe, ++ .remove = brcmvirt_gpio_remove, ++}; ++module_platform_driver(brcmvirt_gpio_driver); ++ ++MODULE_LICENSE("GPL"); ++MODULE_AUTHOR("Dom Cobley "); ++MODULE_DESCRIPTION("brcmvirt GPIO driver"); ++MODULE_ALIAS("platform:brcmvirt-gpio"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0064-OF-DT-Overlay-configfs-interface.patch b/target/linux/bcm27xx/patches-5.10/950-0064-OF-DT-Overlay-configfs-interface.patch new file mode 100644 index 0000000000..bf156927a8 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0064-OF-DT-Overlay-configfs-interface.patch @@ -0,0 +1,427 @@ +From 3027a12f910d164be1cb7c028dd178409ace7f0a Mon Sep 17 00:00:00 2001 +From: Pantelis Antoniou +Date: Wed, 3 Dec 2014 13:23:28 +0200 +Subject: [PATCH] OF: DT-Overlay configfs interface + +This is a port of Pantelis Antoniou's v3 port that makes use of the +new upstreamed configfs support for binary attributes. + +Original commit message: + +Add a runtime interface to using configfs for generic device tree overlay +usage. With it its possible to use device tree overlays without having +to use a per-platform overlay manager. + +Please see Documentation/devicetree/configfs-overlays.txt for more info. + +Changes since v2: +- Removed ifdef CONFIG_OF_OVERLAY (since for now it's required) +- Created a documentation entry +- Slight rewording in Kconfig + +Changes since v1: +- of_resolve() -> of_resolve_phandles(). + +Originally-signed-off-by: Pantelis Antoniou +Signed-off-by: Phil Elwell + +DT configfs: Fix build errors on other platforms + +Signed-off-by: Phil Elwell + +DT configfs: fix build error + +There is an error when compiling rpi-4.6.y branch: + CC drivers/of/configfs.o +drivers/of/configfs.c:291:21: error: initialization from incompatible pointer type [-Werror=incompatible-pointer-types] + .default_groups = of_cfs_def_groups, + ^ +drivers/of/configfs.c:291:21: note: (near initialization for 'of_cfs_subsys.su_group.default_groups.next') + +The .default_groups is linked list since commit +1ae1602de028acaa42a0f6ff18d19756f8e825c6. +This commit uses configfs_add_default_group to fix this problem. + +Signed-off-by: Slawomir Stepien + +configfs: New of_overlay API +--- + .../devicetree/configfs-overlays.txt | 31 ++ + drivers/of/Kconfig | 7 + + drivers/of/Makefile | 1 + + drivers/of/configfs.c | 310 ++++++++++++++++++ + 4 files changed, 349 insertions(+) + create mode 100644 Documentation/devicetree/configfs-overlays.txt + create mode 100644 drivers/of/configfs.c + +--- /dev/null ++++ b/Documentation/devicetree/configfs-overlays.txt +@@ -0,0 +1,31 @@ ++Howto use the configfs overlay interface. ++ ++A device-tree configfs entry is created in /config/device-tree/overlays ++and and it is manipulated using standard file system I/O. ++Note that this is a debug level interface, for use by developers and ++not necessarily something accessed by normal users due to the ++security implications of having direct access to the kernel's device tree. ++ ++* To create an overlay you mkdir the directory: ++ ++ # mkdir /config/device-tree/overlays/foo ++ ++* Either you echo the overlay firmware file to the path property file. ++ ++ # echo foo.dtbo >/config/device-tree/overlays/foo/path ++ ++* Or you cat the contents of the overlay to the dtbo file ++ ++ # cat foo.dtbo >/config/device-tree/overlays/foo/dtbo ++ ++The overlay file will be applied, and devices will be created/destroyed ++as required. ++ ++To remove it simply rmdir the directory. ++ ++ # rmdir /config/device-tree/overlays/foo ++ ++The rationalle of the dual interface (firmware & direct copy) is that each is ++better suited to different use patterns. The firmware interface is what's ++intended to be used by hardware managers in the kernel, while the copy interface ++make sense for developers (since it avoids problems with namespaces). +--- a/drivers/of/Kconfig ++++ b/drivers/of/Kconfig +@@ -100,4 +100,11 @@ config OF_DMA_DEFAULT_COHERENT + # arches should select this if DMA is coherent by default for OF devices + bool + ++config OF_CONFIGFS ++ bool "Device Tree Overlay ConfigFS interface" ++ select CONFIGFS_FS ++ select OF_OVERLAY ++ help ++ Enable a simple user-space driven DT overlay interface. ++ + endif # OF +--- a/drivers/of/Makefile ++++ b/drivers/of/Makefile +@@ -1,6 +1,7 @@ + # SPDX-License-Identifier: GPL-2.0 + obj-y = base.o device.o platform.o property.o + obj-$(CONFIG_OF_KOBJ) += kobj.o ++obj-$(CONFIG_OF_CONFIGFS) += configfs.o + obj-$(CONFIG_OF_DYNAMIC) += dynamic.o + obj-$(CONFIG_OF_FLATTREE) += fdt.o + obj-$(CONFIG_OF_EARLY_FLATTREE) += fdt_address.o +--- /dev/null ++++ b/drivers/of/configfs.c +@@ -0,0 +1,310 @@ ++/* ++ * Configfs entries for device-tree ++ * ++ * Copyright (C) 2013 - Pantelis Antoniou ++ * ++ * This program is free software; you can redistribute it and/or ++ * modify it under the terms of the GNU General Public License ++ * as published by the Free Software Foundation; either version ++ * 2 of the License, or (at your option) any later version. ++ */ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "of_private.h" ++ ++struct cfs_overlay_item { ++ struct config_item item; ++ ++ char path[PATH_MAX]; ++ ++ const struct firmware *fw; ++ struct device_node *overlay; ++ int ov_id; ++ ++ void *dtbo; ++ int dtbo_size; ++}; ++ ++static int create_overlay(struct cfs_overlay_item *overlay, void *blob) ++{ ++ int err; ++ ++ /* unflatten the tree */ ++ of_fdt_unflatten_tree(blob, NULL, &overlay->overlay); ++ if (overlay->overlay == NULL) { ++ pr_err("%s: failed to unflatten tree\n", __func__); ++ err = -EINVAL; ++ goto out_err; ++ } ++ pr_debug("%s: unflattened OK\n", __func__); ++ ++ /* mark it as detached */ ++ of_node_set_flag(overlay->overlay, OF_DETACHED); ++ ++ /* perform resolution */ ++ err = of_resolve_phandles(overlay->overlay); ++ if (err != 0) { ++ pr_err("%s: Failed to resolve tree\n", __func__); ++ goto out_err; ++ } ++ pr_debug("%s: resolved OK\n", __func__); ++ ++ err = of_overlay_apply(overlay->overlay, &overlay->ov_id); ++ if (err < 0) { ++ pr_err("%s: Failed to create overlay (err=%d)\n", ++ __func__, err); ++ goto out_err; ++ } ++ ++out_err: ++ return err; ++} ++ ++static inline struct cfs_overlay_item *to_cfs_overlay_item( ++ struct config_item *item) ++{ ++ return item ? container_of(item, struct cfs_overlay_item, item) : NULL; ++} ++ ++static ssize_t cfs_overlay_item_path_show(struct config_item *item, ++ char *page) ++{ ++ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item); ++ return sprintf(page, "%s\n", overlay->path); ++} ++ ++static ssize_t cfs_overlay_item_path_store(struct config_item *item, ++ const char *page, size_t count) ++{ ++ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item); ++ const char *p = page; ++ char *s; ++ int err; ++ ++ /* if it's set do not allow changes */ ++ if (overlay->path[0] != '\0' || overlay->dtbo_size > 0) ++ return -EPERM; ++ ++ /* copy to path buffer (and make sure it's always zero terminated */ ++ count = snprintf(overlay->path, sizeof(overlay->path) - 1, "%s", p); ++ overlay->path[sizeof(overlay->path) - 1] = '\0'; ++ ++ /* strip trailing newlines */ ++ s = overlay->path + strlen(overlay->path); ++ while (s > overlay->path && *--s == '\n') ++ *s = '\0'; ++ ++ pr_debug("%s: path is '%s'\n", __func__, overlay->path); ++ ++ err = request_firmware(&overlay->fw, overlay->path, NULL); ++ if (err != 0) ++ goto out_err; ++ ++ err = create_overlay(overlay, (void *)overlay->fw->data); ++ if (err != 0) ++ goto out_err; ++ ++ return count; ++ ++out_err: ++ ++ release_firmware(overlay->fw); ++ overlay->fw = NULL; ++ ++ overlay->path[0] = '\0'; ++ return err; ++} ++ ++static ssize_t cfs_overlay_item_status_show(struct config_item *item, ++ char *page) ++{ ++ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item); ++ ++ return sprintf(page, "%s\n", ++ overlay->ov_id >= 0 ? "applied" : "unapplied"); ++} ++ ++CONFIGFS_ATTR(cfs_overlay_item_, path); ++CONFIGFS_ATTR_RO(cfs_overlay_item_, status); ++ ++static struct configfs_attribute *cfs_overlay_attrs[] = { ++ &cfs_overlay_item_attr_path, ++ &cfs_overlay_item_attr_status, ++ NULL, ++}; ++ ++ssize_t cfs_overlay_item_dtbo_read(struct config_item *item, ++ void *buf, size_t max_count) ++{ ++ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item); ++ ++ pr_debug("%s: buf=%p max_count=%zu\n", __func__, ++ buf, max_count); ++ ++ if (overlay->dtbo == NULL) ++ return 0; ++ ++ /* copy if buffer provided */ ++ if (buf != NULL) { ++ /* the buffer must be large enough */ ++ if (overlay->dtbo_size > max_count) ++ return -ENOSPC; ++ ++ memcpy(buf, overlay->dtbo, overlay->dtbo_size); ++ } ++ ++ return overlay->dtbo_size; ++} ++ ++ssize_t cfs_overlay_item_dtbo_write(struct config_item *item, ++ const void *buf, size_t count) ++{ ++ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item); ++ int err; ++ ++ /* if it's set do not allow changes */ ++ if (overlay->path[0] != '\0' || overlay->dtbo_size > 0) ++ return -EPERM; ++ ++ /* copy the contents */ ++ overlay->dtbo = kmemdup(buf, count, GFP_KERNEL); ++ if (overlay->dtbo == NULL) ++ return -ENOMEM; ++ ++ overlay->dtbo_size = count; ++ ++ err = create_overlay(overlay, overlay->dtbo); ++ if (err != 0) ++ goto out_err; ++ ++ return count; ++ ++out_err: ++ kfree(overlay->dtbo); ++ overlay->dtbo = NULL; ++ overlay->dtbo_size = 0; ++ ++ return err; ++} ++ ++CONFIGFS_BIN_ATTR(cfs_overlay_item_, dtbo, NULL, SZ_1M); ++ ++static struct configfs_bin_attribute *cfs_overlay_bin_attrs[] = { ++ &cfs_overlay_item_attr_dtbo, ++ NULL, ++}; ++ ++static void cfs_overlay_release(struct config_item *item) ++{ ++ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item); ++ ++ if (overlay->ov_id >= 0) ++ of_overlay_remove(&overlay->ov_id); ++ if (overlay->fw) ++ release_firmware(overlay->fw); ++ /* kfree with NULL is safe */ ++ kfree(overlay->dtbo); ++ kfree(overlay); ++} ++ ++static struct configfs_item_operations cfs_overlay_item_ops = { ++ .release = cfs_overlay_release, ++}; ++ ++static struct config_item_type cfs_overlay_type = { ++ .ct_item_ops = &cfs_overlay_item_ops, ++ .ct_attrs = cfs_overlay_attrs, ++ .ct_bin_attrs = cfs_overlay_bin_attrs, ++ .ct_owner = THIS_MODULE, ++}; ++ ++static struct config_item *cfs_overlay_group_make_item( ++ struct config_group *group, const char *name) ++{ ++ struct cfs_overlay_item *overlay; ++ ++ overlay = kzalloc(sizeof(*overlay), GFP_KERNEL); ++ if (!overlay) ++ return ERR_PTR(-ENOMEM); ++ overlay->ov_id = -1; ++ ++ config_item_init_type_name(&overlay->item, name, &cfs_overlay_type); ++ return &overlay->item; ++} ++ ++static void cfs_overlay_group_drop_item(struct config_group *group, ++ struct config_item *item) ++{ ++ struct cfs_overlay_item *overlay = to_cfs_overlay_item(item); ++ ++ config_item_put(&overlay->item); ++} ++ ++static struct configfs_group_operations overlays_ops = { ++ .make_item = cfs_overlay_group_make_item, ++ .drop_item = cfs_overlay_group_drop_item, ++}; ++ ++static struct config_item_type overlays_type = { ++ .ct_group_ops = &overlays_ops, ++ .ct_owner = THIS_MODULE, ++}; ++ ++static struct configfs_group_operations of_cfs_ops = { ++ /* empty - we don't allow anything to be created */ ++}; ++ ++static struct config_item_type of_cfs_type = { ++ .ct_group_ops = &of_cfs_ops, ++ .ct_owner = THIS_MODULE, ++}; ++ ++struct config_group of_cfs_overlay_group; ++ ++static struct configfs_subsystem of_cfs_subsys = { ++ .su_group = { ++ .cg_item = { ++ .ci_namebuf = "device-tree", ++ .ci_type = &of_cfs_type, ++ }, ++ }, ++ .su_mutex = __MUTEX_INITIALIZER(of_cfs_subsys.su_mutex), ++}; ++ ++static int __init of_cfs_init(void) ++{ ++ int ret; ++ ++ pr_info("%s\n", __func__); ++ ++ config_group_init(&of_cfs_subsys.su_group); ++ config_group_init_type_name(&of_cfs_overlay_group, "overlays", ++ &overlays_type); ++ configfs_add_default_group(&of_cfs_overlay_group, ++ &of_cfs_subsys.su_group); ++ ++ ret = configfs_register_subsystem(&of_cfs_subsys); ++ if (ret != 0) { ++ pr_err("%s: failed to register subsys\n", __func__); ++ goto out; ++ } ++ pr_info("%s: OK\n", __func__); ++out: ++ return ret; ++} ++late_initcall(of_cfs_init); diff --git a/target/linux/bcm27xx/patches-5.10/950-0065-hci_h5-Don-t-send-conf_req-when-ACTIVE.patch b/target/linux/bcm27xx/patches-5.10/950-0065-hci_h5-Don-t-send-conf_req-when-ACTIVE.patch new file mode 100644 index 0000000000..495911c664 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0065-hci_h5-Don-t-send-conf_req-when-ACTIVE.patch @@ -0,0 +1,23 @@ +From 32fe7cc286f4a4d7f5d623ddb9fba10907c2abea Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 17 Dec 2015 13:37:07 +0000 +Subject: [PATCH] hci_h5: Don't send conf_req when ACTIVE + +Without this patch, a modem and kernel can continuously bombard each +other with conf_req and conf_rsp messages, in a demented game of tag. +--- + drivers/bluetooth/hci_h5.c | 3 ++- + 1 file changed, 2 insertions(+), 1 deletion(-) + +--- a/drivers/bluetooth/hci_h5.c ++++ b/drivers/bluetooth/hci_h5.c +@@ -343,7 +343,8 @@ static void h5_handle_internal_rx(struct + h5_link_control(hu, conf_req, 3); + } else if (memcmp(data, conf_req, 2) == 0) { + h5_link_control(hu, conf_rsp, 2); +- h5_link_control(hu, conf_req, 3); ++ if (h5->state != H5_ACTIVE) ++ h5_link_control(hu, conf_req, 3); + } else if (memcmp(data, conf_rsp, 2) == 0) { + if (H5_HDR_LEN(hdr) > 2) + h5->tx_win = (data[2] & 0x07); diff --git a/target/linux/bcm27xx/patches-5.10/950-0066-ARM64-Round-Robin-dispatch-IRQs-between-CPUs.patch b/target/linux/bcm27xx/patches-5.10/950-0066-ARM64-Round-Robin-dispatch-IRQs-between-CPUs.patch new file mode 100644 index 0000000000..51bc70aed5 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0066-ARM64-Round-Robin-dispatch-IRQs-between-CPUs.patch @@ -0,0 +1,72 @@ +From 443eb00795c4da76e3877ae7448697ba14584596 Mon Sep 17 00:00:00 2001 +From: Michael Zoran +Date: Sat, 14 Jan 2017 21:43:57 -0800 +Subject: [PATCH] ARM64: Round-Robin dispatch IRQs between CPUs. + +IRQ-CPU mapping is round robined on ARM64 to increase +concurrency and allow multiple interrupts to be serviced +at a time. This reduces the need for FIQ. + +Signed-off-by: Michael Zoran +--- + drivers/irqchip/irq-bcm2835.c | 15 ++++++++++++++- + drivers/irqchip/irq-bcm2836.c | 21 +++++++++++++++++++++ + 2 files changed, 35 insertions(+), 1 deletion(-) + +--- a/drivers/irqchip/irq-bcm2835.c ++++ b/drivers/irqchip/irq-bcm2835.c +@@ -154,10 +154,23 @@ static void armctrl_unmask_irq(struct ir + } + } + ++#ifdef CONFIG_ARM64 ++void bcm2836_arm_irqchip_spin_gpu_irq(void); ++ ++static void armctrl_ack_irq(struct irq_data *d) ++{ ++ bcm2836_arm_irqchip_spin_gpu_irq(); ++} ++ ++#endif ++ + static struct irq_chip armctrl_chip = { + .name = "ARMCTRL-level", + .irq_mask = armctrl_mask_irq, +- .irq_unmask = armctrl_unmask_irq ++ .irq_unmask = armctrl_unmask_irq, ++#ifdef CONFIG_ARM64 ++ .irq_ack = armctrl_ack_irq ++#endif + }; + + static int armctrl_xlate(struct irq_domain *d, struct device_node *ctrlr, +--- a/drivers/irqchip/irq-bcm2836.c ++++ b/drivers/irqchip/irq-bcm2836.c +@@ -87,6 +87,27 @@ static void bcm2836_arm_irqchip_unmask_g + { + } + ++#ifdef CONFIG_ARM64 ++ ++void bcm2836_arm_irqchip_spin_gpu_irq(void) ++{ ++ u32 i; ++ void __iomem *gpurouting = (intc.base + LOCAL_GPU_ROUTING); ++ u32 routing_val = readl(gpurouting); ++ ++ for (i = 1; i <= 3; i++) { ++ u32 new_routing_val = (routing_val + i) & 3; ++ ++ if (cpu_active(new_routing_val)) { ++ writel(new_routing_val, gpurouting); ++ return; ++ } ++ } ++} ++EXPORT_SYMBOL(bcm2836_arm_irqchip_spin_gpu_irq); ++ ++#endif ++ + static struct irq_chip bcm2836_arm_irqchip_gpu = { + .name = "bcm2836-gpu", + .irq_mask = bcm2836_arm_irqchip_mask_gpu_irq, diff --git a/target/linux/bcm27xx/patches-5.10/950-0067-ARM64-Force-hardware-emulation-of-deprecated-instruc.patch b/target/linux/bcm27xx/patches-5.10/950-0067-ARM64-Force-hardware-emulation-of-deprecated-instruc.patch new file mode 100644 index 0000000000..b3c37af92a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0067-ARM64-Force-hardware-emulation-of-deprecated-instruc.patch @@ -0,0 +1,28 @@ +From b4e6e3b95c4f41b415d9d7fed7f121a1850af042 Mon Sep 17 00:00:00 2001 +From: Michael Zoran +Date: Sat, 11 Feb 2017 01:18:31 -0800 +Subject: [PATCH] ARM64: Force hardware emulation of deprecated + instructions. + +--- + arch/arm64/kernel/armv8_deprecated.c | 5 +++++ + 1 file changed, 5 insertions(+) + +--- a/arch/arm64/kernel/armv8_deprecated.c ++++ b/arch/arm64/kernel/armv8_deprecated.c +@@ -182,10 +182,15 @@ static void __init register_insn_emulati + + switch (ops->status) { + case INSN_DEPRECATED: ++#if 0 + insn->current_mode = INSN_EMULATE; + /* Disable the HW mode if it was turned on at early boot time */ + run_all_cpu_set_hw_mode(insn, false); ++#else ++ insn->current_mode = INSN_HW; ++ run_all_cpu_set_hw_mode(insn, true); + insn->max = INSN_HW; ++#endif + break; + case INSN_OBSOLETE: + insn->current_mode = INSN_UNDEF; diff --git a/target/linux/bcm27xx/patches-5.10/950-0068-cache-export-clean-and-invalidate.patch b/target/linux/bcm27xx/patches-5.10/950-0068-cache-export-clean-and-invalidate.patch new file mode 100644 index 0000000000..a468367f49 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0068-cache-export-clean-and-invalidate.patch @@ -0,0 +1,53 @@ +From c9cb22efe558ee7fb1f30deb19dfe7b7bfe1f369 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Fri, 25 Aug 2017 19:18:13 +0100 +Subject: [PATCH] cache: export clean and invalidate + +hack: cache: Fix linker error +--- + arch/arm/mm/cache-v6.S | 4 ++-- + arch/arm/mm/cache-v7.S | 6 ++++-- + 2 files changed, 6 insertions(+), 4 deletions(-) + +--- a/arch/arm/mm/cache-v6.S ++++ b/arch/arm/mm/cache-v6.S +@@ -198,7 +198,7 @@ ENTRY(v6_flush_kern_dcache_area) + * - start - virtual start address of region + * - end - virtual end address of region + */ +-v6_dma_inv_range: ++ENTRY(v6_dma_inv_range) + #ifdef CONFIG_DMA_CACHE_RWFO + ldrb r2, [r0] @ read for ownership + strb r2, [r0] @ write for ownership +@@ -243,7 +243,7 @@ v6_dma_inv_range: + * - start - virtual start address of region + * - end - virtual end address of region + */ +-v6_dma_clean_range: ++ENTRY(v6_dma_clean_range) + bic r0, r0, #D_CACHE_LINE_SIZE - 1 + 1: + #ifdef CONFIG_DMA_CACHE_RWFO +--- a/arch/arm/mm/cache-v7.S ++++ b/arch/arm/mm/cache-v7.S +@@ -363,7 +363,8 @@ ENDPROC(v7_flush_kern_dcache_area) + * - start - virtual start address of region + * - end - virtual end address of region + */ +-v7_dma_inv_range: ++ENTRY(b15_dma_inv_range) ++ENTRY(v7_dma_inv_range) + dcache_line_size r2, r3 + sub r3, r2, #1 + tst r0, r3 +@@ -393,7 +394,8 @@ ENDPROC(v7_dma_inv_range) + * - start - virtual start address of region + * - end - virtual end address of region + */ +-v7_dma_clean_range: ++ENTRY(b15_dma_clean_range) ++ENTRY(v7_dma_clean_range) + dcache_line_size r2, r3 + sub r3, r2, #1 + bic r0, r0, r3 diff --git a/target/linux/bcm27xx/patches-5.10/950-0069-AXI-performance-monitor-driver-2222.patch b/target/linux/bcm27xx/patches-5.10/950-0069-AXI-performance-monitor-driver-2222.patch new file mode 100644 index 0000000000..3358be14a3 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0069-AXI-performance-monitor-driver-2222.patch @@ -0,0 +1,691 @@ +From d9151380fdab4a0f2abcc08d2c344b0eabe48ab9 Mon Sep 17 00:00:00 2001 +From: James Hughes +Date: Tue, 14 Nov 2017 15:13:15 +0000 +Subject: [PATCH] AXI performance monitor driver (#2222) + +Uses the debugfs I/F to provide access to the AXI +bus performance monitors. + +Requires the new mailbox peripheral access for access +to the VPU performance registers, system bus access +is done using direct register reads. + +Signed-off-by: James Hughes + +raspberrypi_axi_monitor: suppress warning + +Suppress the following warning by casting the pointer to and uintptr_t +before to u32: + +Signed-off-by: Matteo Croce +--- + drivers/perf/Kconfig | 8 + + drivers/perf/Makefile | 1 + + drivers/perf/raspberrypi_axi_monitor.c | 637 +++++++++++++++++++++++++ + 3 files changed, 646 insertions(+) + create mode 100644 drivers/perf/raspberrypi_axi_monitor.c + +--- a/drivers/perf/Kconfig ++++ b/drivers/perf/Kconfig +@@ -130,6 +130,14 @@ config ARM_SPE_PMU + Extension, which provides periodic sampling of operations in + the CPU pipeline and reports this via the perf AUX interface. + ++config RPI_AXIPERF ++ depends on ARCH_BCM2835 ++ tristate "RaspberryPi AXI Performance monitors" ++ default n ++ help ++ Say y if you want to use Raspberry Pi AXI performance monitors, m if ++ you want to build it as a module. ++ + source "drivers/perf/hisilicon/Kconfig" + + endmenu +--- a/drivers/perf/Makefile ++++ b/drivers/perf/Makefile +@@ -13,3 +13,4 @@ obj-$(CONFIG_QCOM_L3_PMU) += qcom_l3_pmu + obj-$(CONFIG_THUNDERX2_PMU) += thunderx2_pmu.o + obj-$(CONFIG_XGENE_PMU) += xgene_pmu.o + obj-$(CONFIG_ARM_SPE_PMU) += arm_spe_pmu.o ++obj-$(CONFIG_RPI_AXIPERF) += raspberrypi_axi_monitor.o +--- /dev/null ++++ b/drivers/perf/raspberrypi_axi_monitor.c +@@ -0,0 +1,637 @@ ++/* ++ * raspberrypi_axi_monitor.c ++ * ++ * Author: james.hughes@raspberrypi.org ++ * ++ * Raspberry Pi AXI performance counters. ++ * ++ * Copyright (C) 2017 Raspberry Pi Trading Ltd. ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++ ++#define NUM_MONITORS 2 ++#define NUM_BUS_WATCHERS_PER_MONITOR 3 ++ ++#define SYSTEM_MONITOR 0 ++#define VPU_MONITOR 1 ++ ++#define MAX_BUSES 16 ++#define DEFAULT_SAMPLE_TIME 100 ++ ++#define NUM_BUS_WATCHER_RESULTS 9 ++ ++struct bus_watcher_data { ++ union { ++ u32 results[NUM_BUS_WATCHER_RESULTS]; ++ struct { ++ u32 atrans; ++ u32 atwait; ++ u32 amax; ++ u32 wtrans; ++ u32 wtwait; ++ u32 wmax; ++ u32 rtrans; ++ u32 rtwait; ++ u32 rmax; ++ }; ++ }; ++}; ++ ++ ++struct rpi_axiperf { ++ struct platform_device *dev; ++ struct dentry *root_folder; ++ ++ struct task_struct *monitor_thread; ++ struct mutex lock; ++ ++ struct rpi_firmware *firmware; ++ ++ /* Sample time spent on for each bus */ ++ int sample_time; ++ ++ /* Now storage for the per monitor settings and the resulting ++ * performance figures ++ */ ++ struct { ++ /* Bit field of buses we want to monitor */ ++ int bus_enabled; ++ /* Bit field of buses to filter by */ ++ int bus_filter; ++ /* The current buses being monitored on this monitor */ ++ int current_bus[NUM_BUS_WATCHERS_PER_MONITOR]; ++ /* The last bus monitored on this monitor */ ++ int last_monitored; ++ ++ /* Set true if this mailbox must use the mailbox interface ++ * rather than access registers directly. ++ */ ++ int use_mailbox_interface; ++ ++ /* Current result values */ ++ struct bus_watcher_data results[MAX_BUSES]; ++ ++ struct dentry *debugfs_entry; ++ void __iomem *base_address; ++ ++ } monitor[NUM_MONITORS]; ++ ++}; ++ ++static struct rpi_axiperf *state; ++ ++/* Two monitors, System and VPU, each with the following register sets. ++ * Each monitor can only monitor one bus at a time, so we time share them, ++ * giving each bus 100ms (default, settable via debugfs) of time on its ++ * associated monitor ++ * Record results from the three Bus watchers per monitor and push to the sysfs ++ */ ++ ++/* general registers */ ++const int GEN_CTRL; ++ ++const int GEN_CTL_ENABLE_BIT = BIT(0); ++const int GEN_CTL_RESET_BIT = BIT(1); ++ ++/* Bus watcher registers */ ++const int BW_PITCH = 0x40; ++ ++const int BW0_CTRL = 0x40; ++const int BW1_CTRL = 0x80; ++const int BW2_CTRL = 0xc0; ++ ++const int BW_ATRANS_OFFSET = 0x04; ++const int BW_ATWAIT_OFFSET = 0x08; ++const int BW_AMAX_OFFSET = 0x0c; ++const int BW_WTRANS_OFFSET = 0x10; ++const int BW_WTWAIT_OFFSET = 0x14; ++const int BW_WMAX_OFFSET = 0x18; ++const int BW_RTRANS_OFFSET = 0x1c; ++const int BW_RTWAIT_OFFSET = 0x20; ++const int BW_RMAX_OFFSET = 0x24; ++ ++const int BW_CTRL_RESET_BIT = BIT(31); ++const int BW_CTRL_ENABLE_BIT = BIT(30); ++const int BW_CTRL_ENABLE_ID_FILTER_BIT = BIT(29); ++const int BW_CTRL_LIMIT_HALT_BIT = BIT(28); ++ ++const int BW_CTRL_SOURCE_SHIFT = 8; ++const int BW_CTRL_SOURCE_MASK = GENMASK(12, 8); // 5 bits ++const int BW_CTRL_BUS_WATCH_SHIFT; ++const int BW_CTRL_BUS_WATCH_MASK = GENMASK(5, 0); // 6 bits ++const int BW_CTRL_BUS_FILTER_SHIFT = 8; ++ ++const static char *bus_filter_strings[] = { ++ "", ++ "CORE0_V", ++ "ICACHE0", ++ "DCACHE0", ++ "CORE1_V", ++ "ICACHE1", ++ "DCACHE1", ++ "L2_MAIN", ++ "HOST_PORT", ++ "HOST_PORT2", ++ "HVS", ++ "ISP", ++ "VIDEO_DCT", ++ "VIDEO_SD2AXI", ++ "CAM0", ++ "CAM1", ++ "DMA0", ++ "DMA1", ++ "DMA2_VPU", ++ "JPEG", ++ "VIDEO_CME", ++ "TRANSPOSER", ++ "VIDEO_FME", ++ "CCP2TX", ++ "USB", ++ "V3D0", ++ "V3D1", ++ "V3D2", ++ "AVE", ++ "DEBUG", ++ "CPU", ++ "M30" ++}; ++ ++const int num_bus_filters = ARRAY_SIZE(bus_filter_strings); ++ ++const static char *system_bus_string[] = { ++ "DMA_L2", ++ "TRANS", ++ "JPEG", ++ "SYSTEM_UC", ++ "DMA_UC", ++ "SYSTEM_L2", ++ "CCP2TX", ++ "MPHI_RX", ++ "MPHI_TX", ++ "HVS", ++ "H264", ++ "ISP", ++ "V3D", ++ "PERIPHERAL", ++ "CPU_UC", ++ "CPU_L2" ++}; ++ ++const int num_system_buses = ARRAY_SIZE(system_bus_string); ++ ++const static char *vpu_bus_string[] = { ++ "VPU1_D_L2", ++ "VPU0_D_L2", ++ "VPU1_I_L2", ++ "VPU0_I_L2", ++ "SYSTEM_L2", ++ "L2_FLUSH", ++ "DMA_L2", ++ "VPU1_D_UC", ++ "VPU0_D_UC", ++ "VPU1_I_UC", ++ "VPU0_I_UC", ++ "SYSTEM_UC", ++ "L2_OUT", ++ "DMA_UC", ++ "SDRAM", ++ "L2_IN" ++}; ++ ++const int num_vpu_buses = ARRAY_SIZE(vpu_bus_string); ++ ++const static char *monitor_name[] = { ++ "System", ++ "VPU" ++}; ++ ++static inline void write_reg(int monitor, int reg, u32 value) ++{ ++ writel(value, state->monitor[monitor].base_address + reg); ++} ++ ++static inline u32 read_reg(int monitor, u32 reg) ++{ ++ return readl(state->monitor[monitor].base_address + reg); ++} ++ ++static void read_bus_watcher(int monitor, int watcher, u32 *results) ++{ ++ if (state->monitor[monitor].use_mailbox_interface) { ++ /* We have 9 results, plus the overheads of start address and ++ * length So 11 u32 to define ++ */ ++ u32 tmp[11]; ++ int err; ++ ++ tmp[0] = (u32)(uintptr_t)(state->monitor[monitor].base_address + watcher ++ + BW_ATRANS_OFFSET); ++ tmp[1] = NUM_BUS_WATCHER_RESULTS; ++ ++ err = rpi_firmware_property(state->firmware, ++ RPI_FIRMWARE_GET_PERIPH_REG, ++ tmp, sizeof(tmp)); ++ ++ if (err < 0 || tmp[1] != NUM_BUS_WATCHER_RESULTS) ++ dev_err_once(&state->dev->dev, ++ "Failed to read bus watcher"); ++ else ++ memcpy(results, &tmp[2], ++ NUM_BUS_WATCHER_RESULTS * sizeof(u32)); ++ } else { ++ int i; ++ void __iomem *addr = state->monitor[monitor].base_address ++ + watcher + BW_ATRANS_OFFSET; ++ for (i = 0; i < NUM_BUS_WATCHER_RESULTS; i++, addr += 4) ++ *results++ = readl(addr); ++ } ++} ++ ++static void set_monitor_control(int monitor, u32 set) ++{ ++ if (state->monitor[monitor].use_mailbox_interface) { ++ u32 tmp[3] = {(u32)(uintptr_t)(state->monitor[monitor].base_address + ++ GEN_CTRL), 1, set}; ++ int err = rpi_firmware_property(state->firmware, ++ RPI_FIRMWARE_SET_PERIPH_REG, ++ tmp, sizeof(tmp)); ++ ++ if (err < 0 || tmp[1] != 1) ++ dev_err_once(&state->dev->dev, ++ "Failed to set monitor control"); ++ } else ++ write_reg(monitor, GEN_CTRL, set); ++} ++ ++static void set_bus_watcher_control(int monitor, int watcher, u32 set) ++{ ++ if (state->monitor[monitor].use_mailbox_interface) { ++ u32 tmp[3] = {(u32)(uintptr_t)(state->monitor[monitor].base_address + ++ watcher), 1, set}; ++ int err = rpi_firmware_property(state->firmware, ++ RPI_FIRMWARE_SET_PERIPH_REG, ++ tmp, sizeof(tmp)); ++ if (err < 0 || tmp[1] != 1) ++ dev_err_once(&state->dev->dev, ++ "Failed to set bus watcher control"); ++ } else ++ write_reg(monitor, watcher, set); ++} ++ ++static void monitor(struct rpi_axiperf *state) ++{ ++ int monitor, num_buses[NUM_MONITORS]; ++ ++ mutex_lock(&state->lock); ++ ++ for (monitor = 0; monitor < NUM_MONITORS; monitor++) { ++ typeof(state->monitor[0]) *mon = &(state->monitor[monitor]); ++ ++ /* Anything enabled? */ ++ if (mon->bus_enabled == 0) { ++ /* No, disable all monitoring for this monitor */ ++ set_monitor_control(monitor, GEN_CTL_RESET_BIT); ++ } else { ++ int i; ++ ++ /* Find out how many busses we want to monitor, and ++ * spread our 3 actual monitors over them ++ */ ++ num_buses[monitor] = hweight32(mon->bus_enabled); ++ num_buses[monitor] = min(num_buses[monitor], ++ NUM_BUS_WATCHERS_PER_MONITOR); ++ ++ for (i = 0; i < num_buses[monitor]; i++) { ++ int bus_control; ++ ++ do { ++ mon->last_monitored++; ++ mon->last_monitored &= 0xf; ++ } while ((mon->bus_enabled & ++ (1 << mon->last_monitored)) == 0); ++ ++ mon->current_bus[i] = mon->last_monitored; ++ ++ /* Reset the counters */ ++ set_bus_watcher_control(monitor, ++ BW0_CTRL + ++ i*BW_PITCH, ++ BW_CTRL_RESET_BIT); ++ ++ bus_control = BW_CTRL_ENABLE_BIT | ++ mon->current_bus[i]; ++ ++ if (mon->bus_filter) { ++ bus_control |= ++ BW_CTRL_ENABLE_ID_FILTER_BIT; ++ bus_control |= ++ ((mon->bus_filter & 0x1f) ++ << BW_CTRL_BUS_FILTER_SHIFT); ++ } ++ ++ // Start capture ++ set_bus_watcher_control(monitor, ++ BW0_CTRL + i*BW_PITCH, ++ bus_control); ++ } ++ } ++ ++ /* start monitoring */ ++ set_monitor_control(monitor, GEN_CTL_ENABLE_BIT); ++ } ++ ++ mutex_unlock(&state->lock); ++ ++ msleep(state->sample_time); ++ ++ /* Now read the results */ ++ ++ mutex_lock(&state->lock); ++ for (monitor = 0; monitor < NUM_MONITORS; monitor++) { ++ typeof(state->monitor[0]) *mon = &(state->monitor[monitor]); ++ ++ /* Anything enabled? */ ++ if (mon->bus_enabled == 0) { ++ /* No, disable all monitoring for this monitor */ ++ set_monitor_control(monitor, 0); ++ } else { ++ int i; ++ ++ for (i = 0; i < num_buses[monitor]; i++) { ++ int bus = mon->current_bus[i]; ++ ++ read_bus_watcher(monitor, ++ BW0_CTRL + i*BW_PITCH, ++ (u32 *)&mon->results[bus].results); ++ } ++ } ++ } ++ mutex_unlock(&state->lock); ++} ++ ++static int monitor_thread(void *data) ++{ ++ struct rpi_axiperf *state = data; ++ ++ while (1) { ++ monitor(state); ++ ++ if (kthread_should_stop()) ++ return 0; ++ } ++ return 0; ++} ++ ++static ssize_t myreader(struct file *fp, char __user *user_buffer, ++ size_t count, loff_t *position) ++{ ++#define INIT_BUFF_SIZE 2048 ++ ++ int i; ++ int idx = (int)(uintptr_t)(fp->private_data); ++ int num_buses, cnt; ++ char *string_buffer; ++ int buff_size = INIT_BUFF_SIZE; ++ char *p; ++ typeof(state->monitor[0]) *mon = &(state->monitor[idx]); ++ ++ if (idx < 0 || idx > NUM_MONITORS) ++ idx = 0; ++ ++ num_buses = idx == SYSTEM_MONITOR ? num_system_buses : num_vpu_buses; ++ ++ string_buffer = kmalloc(buff_size, GFP_KERNEL); ++ ++ if (!string_buffer) { ++ dev_err(&state->dev->dev, ++ "Failed temporary string allocation\n"); ++ return 0; ++ } ++ ++ p = string_buffer; ++ ++ mutex_lock(&state->lock); ++ ++ if (mon->bus_filter) { ++ int filt = min(mon->bus_filter & 0x1f, num_bus_filters); ++ ++ cnt = snprintf(p, buff_size, ++ "\nMonitoring transactions from %s only\n", ++ bus_filter_strings[filt]); ++ p += cnt; ++ buff_size -= cnt; ++ } ++ ++ cnt = snprintf(p, buff_size, " Bus | Atrans Atwait AMax Wtrans Wtwait WMax Rtrans Rtwait RMax\n" ++ "======================================================================================================\n"); ++ ++ if (cnt >= buff_size) ++ goto done; ++ ++ p += cnt; ++ buff_size -= cnt; ++ ++ for (i = 0; i < num_buses; i++) { ++ if (mon->bus_enabled & (1 << i)) { ++#define DIVIDER (1024) ++ typeof(mon->results[0]) *res = &(mon->results[i]); ++ ++ cnt = snprintf(p, buff_size, ++ "%10s | %8uK %8uK %8uK %8uK %8uK %8uK %8uK %8uK %8uK\n", ++ idx == SYSTEM_MONITOR ? ++ system_bus_string[i] : ++ vpu_bus_string[i], ++ res->atrans/DIVIDER, ++ res->atwait/DIVIDER, ++ res->amax/DIVIDER, ++ res->wtrans/DIVIDER, ++ res->wtwait/DIVIDER, ++ res->wmax/DIVIDER, ++ res->rtrans/DIVIDER, ++ res->rtwait/DIVIDER, ++ res->rmax/DIVIDER ++ ); ++ if (cnt >= buff_size) ++ goto done; ++ ++ p += cnt; ++ buff_size -= cnt; ++ } ++ } ++ ++ mutex_unlock(&state->lock); ++ ++done: ++ ++ /* did the last string entry exceeed our buffer size? ie out of string ++ * buffer space. Null terminate, use what we have. ++ */ ++ if (cnt >= buff_size) { ++ buff_size = 0; ++ string_buffer[INIT_BUFF_SIZE] = 0; ++ } ++ ++ cnt = simple_read_from_buffer(user_buffer, count, position, ++ string_buffer, ++ INIT_BUFF_SIZE - buff_size); ++ ++ kfree(string_buffer); ++ ++ return cnt; ++} ++ ++static ssize_t mywriter(struct file *fp, const char __user *user_buffer, ++ size_t count, loff_t *position) ++{ ++ int idx = (int)(uintptr_t)(fp->private_data); ++ ++ if (idx < 0 || idx > NUM_MONITORS) ++ idx = 0; ++ ++ /* At the moment, this does nothing, but in the future it could be ++ * used to reset counters etc ++ */ ++ return count; ++} ++ ++static const struct file_operations fops_debug = { ++ .read = myreader, ++ .write = mywriter, ++ .open = simple_open ++}; ++ ++static int rpi_axiperf_probe(struct platform_device *pdev) ++{ ++ int ret = 0, i; ++ struct device *dev = &pdev->dev; ++ struct device_node *np = dev->of_node; ++ struct device_node *fw_node; ++ ++ state = kzalloc(sizeof(struct rpi_axiperf), GFP_KERNEL); ++ if (!state) ++ return -ENOMEM; ++ ++ /* Get the firmware handle for future rpi-firmware-xxx calls */ ++ fw_node = of_parse_phandle(np, "firmware", 0); ++ if (!fw_node) { ++ dev_err(dev, "Missing firmware node\n"); ++ return -ENOENT; ++ } ++ ++ state->firmware = rpi_firmware_get(fw_node); ++ if (!state->firmware) ++ return -EPROBE_DEFER; ++ ++ /* Special case for the VPU monitor, we must use the mailbox interface ++ * as it is not accessible from the ARM address space. ++ */ ++ state->monitor[VPU_MONITOR].use_mailbox_interface = 1; ++ state->monitor[SYSTEM_MONITOR].use_mailbox_interface = 0; ++ ++ for (i = 0; i < NUM_MONITORS; i++) { ++ if (state->monitor[i].use_mailbox_interface) { ++ of_property_read_u32_index(np, "reg", i*2, ++ (u32 *)(&state->monitor[i].base_address)); ++ } else { ++ struct resource *resource = ++ platform_get_resource(pdev, IORESOURCE_MEM, i); ++ ++ state->monitor[i].base_address = ++ devm_ioremap_resource(&pdev->dev, resource); ++ } ++ ++ if (IS_ERR(state->monitor[i].base_address)) ++ return PTR_ERR(state->monitor[i].base_address); ++ ++ /* Enable all buses by default */ ++ state->monitor[i].bus_enabled = 0xffff; ++ } ++ ++ state->dev = pdev; ++ platform_set_drvdata(pdev, state); ++ ++ state->sample_time = DEFAULT_SAMPLE_TIME; ++ ++ /* Set up all the debugfs stuff */ ++ state->root_folder = debugfs_create_dir(KBUILD_MODNAME, NULL); ++ ++ for (i = 0; i < NUM_MONITORS; i++) { ++ state->monitor[i].debugfs_entry = ++ debugfs_create_dir(monitor_name[i], state->root_folder); ++ if (IS_ERR(state->monitor[i].debugfs_entry)) ++ state->monitor[i].debugfs_entry = NULL; ++ ++ debugfs_create_file("data", 0444, ++ state->monitor[i].debugfs_entry, ++ (void *)(uintptr_t)i, &fops_debug); ++ debugfs_create_u32("enable", 0644, ++ state->monitor[i].debugfs_entry, ++ &state->monitor[i].bus_enabled); ++ debugfs_create_u32("filter", 0644, ++ state->monitor[i].debugfs_entry, ++ &state->monitor[i].bus_filter); ++ debugfs_create_u32("sample_time", 0644, ++ state->monitor[i].debugfs_entry, ++ &state->sample_time); ++ } ++ ++ mutex_init(&state->lock); ++ ++ state->monitor_thread = kthread_run(monitor_thread, state, ++ "rpi-axiperfmon"); ++ ++ return ret; ++ ++} ++ ++static int rpi_axiperf_remove(struct platform_device *dev) ++{ ++ int ret = 0; ++ ++ kthread_stop(state->monitor_thread); ++ ++ debugfs_remove_recursive(state->root_folder); ++ state->root_folder = NULL; ++ ++ return ret; ++} ++ ++static const struct of_device_id rpi_axiperf_match[] = { ++ { ++ .compatible = "brcm,bcm2835-axiperf", ++ }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, rpi_axiperf_match); ++ ++static struct platform_driver rpi_axiperf_driver = { ++ .probe = rpi_axiperf_probe, ++ .remove = rpi_axiperf_remove, ++ .driver = { ++ .name = "rpi-bcm2835-axiperf", ++ .of_match_table = of_match_ptr(rpi_axiperf_match), ++ }, ++}; ++ ++module_platform_driver(rpi_axiperf_driver); ++ ++/* Module information */ ++MODULE_AUTHOR("James Hughes "); ++MODULE_DESCRIPTION("RPI AXI Performance monitor driver"); ++MODULE_LICENSE("GPL"); ++ diff --git a/target/linux/bcm27xx/patches-5.10/950-0070-ARM-bcm2835-Set-Serial-number-and-Revision.patch b/target/linux/bcm27xx/patches-5.10/950-0070-ARM-bcm2835-Set-Serial-number-and-Revision.patch new file mode 100644 index 0000000000..7ce4c48f65 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0070-ARM-bcm2835-Set-Serial-number-and-Revision.patch @@ -0,0 +1,63 @@ +From 65565784e5faad0af487d54f3f92d9d4c9c38e4a Mon Sep 17 00:00:00 2001 +From: =?UTF-8?q?Noralf=20Tr=C3=B8nnes?= +Date: Wed, 3 Jun 2015 12:26:13 +0200 +Subject: [PATCH] ARM: bcm2835: Set Serial number and Revision +MIME-Version: 1.0 +Content-Type: text/plain; charset=UTF-8 +Content-Transfer-Encoding: 8bit + +The VideoCore bootloader passes in Serial number and +Revision number through Device Tree. Make these available to +userspace through /proc/cpuinfo. + +Mainline status: + +There is a commit in linux-next that standardize passing the serial +number through Device Tree (string: /serial-number): +ARM: 8355/1: arch: Show the serial number from devicetree in cpuinfo + +There was an attempt to do the same with the revision number, but it +didn't get in: +[PATCH v2 1/2] arm: devtree: Set system_rev from DT revision + +Signed-off-by: Noralf Trønnes +--- + arch/arm/mach-bcm/board_bcm2835.c | 14 ++++++++++++++ + 1 file changed, 14 insertions(+) + +--- a/arch/arm/mach-bcm/board_bcm2835.c ++++ b/arch/arm/mach-bcm/board_bcm2835.c +@@ -6,12 +6,25 @@ + #include + #include + #include ++#include + + #include + #include + + #include "platsmp.h" + ++static void __init bcm2835_init(void) ++{ ++ struct device_node *np = of_find_node_by_path("/system"); ++ u32 val; ++ u64 val64; ++ ++ if (!of_property_read_u32(np, "linux,revision", &val)) ++ system_rev = val; ++ if (!of_property_read_u64(np, "linux,serial", &val64)) ++ system_serial_low = val64; ++} ++ + static const char * const bcm2835_compat[] = { + #ifdef CONFIG_ARCH_MULTI_V6 + "brcm,bcm2835", +@@ -24,6 +37,7 @@ static const char * const bcm2835_compat + }; + + DT_MACHINE_START(BCM2835, "BCM2835") ++ .init_machine = bcm2835_init, + .dt_compat = bcm2835_compat, + .smp = smp_ops(bcm2836_smp_ops), + MACHINE_END diff --git a/target/linux/bcm27xx/patches-5.10/950-0071-dwc-otg-FIQ-Fix-bad-mode-in-data-abort-handler.patch b/target/linux/bcm27xx/patches-5.10/950-0071-dwc-otg-FIQ-Fix-bad-mode-in-data-abort-handler.patch new file mode 100644 index 0000000000..b93a62d4fb --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0071-dwc-otg-FIQ-Fix-bad-mode-in-data-abort-handler.patch @@ -0,0 +1,116 @@ +From 347167bd9ac2a68870064edd921f2525bd569c6d Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 16 Jul 2018 14:40:13 +0100 +Subject: [PATCH] dwc-otg: FIQ: Fix "bad mode in data abort handler" + +Create a semi-static mapping for the USB registers early in the boot +process, before additional kernel threads are started, so all threads +will have the mappings from the start. This avoids the need for +data aborts to lazily update them. + +See: https://github.com/raspberrypi/linux/issues/2450 + +Signed-off-by: Floris Bos +--- + arch/arm/mach-bcm/board_bcm2835.c | 69 +++++++++++++++++++++++++++++++ + 1 file changed, 69 insertions(+) + +--- a/arch/arm/mach-bcm/board_bcm2835.c ++++ b/arch/arm/mach-bcm/board_bcm2835.c +@@ -6,6 +6,7 @@ + #include + #include + #include ++#include + #include + + #include +@@ -13,6 +14,9 @@ + + #include "platsmp.h" + ++#define BCM2835_USB_VIRT_BASE 0xf0980000 ++#define BCM2835_USB_VIRT_MPHI 0xf0006000 ++ + static void __init bcm2835_init(void) + { + struct device_node *np = of_find_node_by_path("/system"); +@@ -25,6 +29,70 @@ static void __init bcm2835_init(void) + system_serial_low = val64; + } + ++/* ++ * We need to map registers that are going to be accessed by the FIQ ++ * very early, before any kernel threads are spawned. Because if done ++ * later, the mapping tables are not updated instantly but lazily upon ++ * first access through a data abort handler. While that is fine ++ * when executing regular kernel code, if the first access in a specific ++ * thread happens while running FIQ code this will result in a panic. ++ * ++ * For more background see the following old mailing list thread: ++ * https://www.spinics.net/lists/arm-kernel/msg325250.html ++ */ ++static int __init bcm2835_map_usb(unsigned long node, const char *uname, ++ int depth, void *data) ++{ ++ struct map_desc map[2]; ++ const __be32 *reg; ++ int len; ++ unsigned long p2b_offset = *((unsigned long *) data); ++ ++ if (!of_flat_dt_is_compatible(node, "brcm,bcm2708-usb")) ++ return 0; ++ reg = of_get_flat_dt_prop(node, "reg", &len); ++ if (!reg || len != (sizeof(unsigned long) * 4)) ++ return 0; ++ ++ /* Use information about the physical addresses of the ++ * registers from the device tree, but use legacy ++ * iotable_init() static mapping function to map them, ++ * as ioremap() is not functional at this stage in boot. ++ */ ++ map[0].virtual = (unsigned long) BCM2835_USB_VIRT_BASE; ++ map[0].pfn = __phys_to_pfn(be32_to_cpu(reg[0]) - p2b_offset); ++ map[0].length = be32_to_cpu(reg[1]); ++ map[0].type = MT_DEVICE; ++ map[1].virtual = (unsigned long) BCM2835_USB_VIRT_MPHI; ++ map[1].pfn = __phys_to_pfn(be32_to_cpu(reg[2]) - p2b_offset); ++ map[1].length = be32_to_cpu(reg[3]); ++ map[1].type = MT_DEVICE; ++ iotable_init(map, 2); ++ ++ return 1; ++} ++ ++static void __init bcm2835_map_io(void) ++{ ++ const __be32 *ranges; ++ int soc, len; ++ unsigned long p2b_offset; ++ ++ debug_ll_io_init(); ++ ++ /* Find out how to map bus to physical address first from soc/ranges */ ++ soc = of_get_flat_dt_subnode_by_name(of_get_flat_dt_root(), "soc"); ++ if (soc < 0) ++ return; ++ ranges = of_get_flat_dt_prop(soc, "ranges", &len); ++ if (!ranges || len < (sizeof(unsigned long) * 3)) ++ return; ++ p2b_offset = be32_to_cpu(ranges[0]) - be32_to_cpu(ranges[1]); ++ ++ /* Now search for bcm2708-usb node in device tree */ ++ of_scan_flat_dt(bcm2835_map_usb, &p2b_offset); ++} ++ + static const char * const bcm2835_compat[] = { + #ifdef CONFIG_ARCH_MULTI_V6 + "brcm,bcm2835", +@@ -37,6 +105,7 @@ static const char * const bcm2835_compat + }; + + DT_MACHINE_START(BCM2835, "BCM2835") ++ .map_io = bcm2835_map_io, + .init_machine = bcm2835_init, + .dt_compat = bcm2835_compat, + .smp = smp_ops(bcm2836_smp_ops), diff --git a/target/linux/bcm27xx/patches-5.10/950-0072-ARM-Activate-FIQs-to-avoid-__irq_startup-warnings.patch b/target/linux/bcm27xx/patches-5.10/950-0072-ARM-Activate-FIQs-to-avoid-__irq_startup-warnings.patch new file mode 100644 index 0000000000..99acfdd00d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0072-ARM-Activate-FIQs-to-avoid-__irq_startup-warnings.patch @@ -0,0 +1,36 @@ +From 594abebdffdcff606bc445f2661d9a504f180136 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 11 Dec 2017 09:18:32 +0000 +Subject: [PATCH] ARM: Activate FIQs to avoid __irq_startup warnings + +There is a new test in __irq_startup that the IRQ is activated, which +hasn't been the case for FIQs since they bypass some of the usual setup. + +Augment enable_fiq to include a call to irq_activate to avoid the +warning. + +Signed-off-by: Phil Elwell +--- + arch/arm/kernel/fiq.c | 4 ++++ + 1 file changed, 4 insertions(+) + +--- a/arch/arm/kernel/fiq.c ++++ b/arch/arm/kernel/fiq.c +@@ -56,6 +56,8 @@ + static unsigned long dfl_fiq_insn; + static struct pt_regs dfl_fiq_regs; + ++extern int irq_activate(struct irq_desc *desc); ++ + /* Default reacquire function + * - we always relinquish FIQ control + * - we always reacquire FIQ control +@@ -140,6 +142,8 @@ static int fiq_start; + + void enable_fiq(int fiq) + { ++ struct irq_desc *desc = irq_to_desc(fiq + fiq_start); ++ irq_activate(desc); + enable_irq(fiq + fiq_start); + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0073-raspberrypi-firmware-Export-the-general-transaction-.patch b/target/linux/bcm27xx/patches-5.10/950-0073-raspberrypi-firmware-Export-the-general-transaction-.patch new file mode 100644 index 0000000000..8450d5f48a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0073-raspberrypi-firmware-Export-the-general-transaction-.patch @@ -0,0 +1,32 @@ +From 9cf689eda644ccba0c80982cbd821c9163f5de39 Mon Sep 17 00:00:00 2001 +From: Eric Anholt +Date: Wed, 14 Sep 2016 09:16:19 +0100 +Subject: [PATCH] raspberrypi-firmware: Export the general transaction + function. + +The vc4-firmware-kms module is going to be doing the MBOX FB call. + +Signed-off-by: Eric Anholt +--- + drivers/firmware/raspberrypi.c | 3 ++- + 1 file changed, 2 insertions(+), 1 deletion(-) + +--- a/drivers/firmware/raspberrypi.c ++++ b/drivers/firmware/raspberrypi.c +@@ -43,7 +43,7 @@ static void response_callback(struct mbo + * Sends a request to the firmware through the BCM2835 mailbox driver, + * and synchronously waits for the reply. + */ +-static int ++int + rpi_firmware_transaction(struct rpi_firmware *fw, u32 chan, u32 data) + { + u32 message = MBOX_MSG(chan, data); +@@ -68,6 +68,7 @@ rpi_firmware_transaction(struct rpi_firm + + return ret; + } ++EXPORT_SYMBOL_GPL(rpi_firmware_transaction); + + /** + * rpi_firmware_property_list - Submit firmware property list diff --git a/target/linux/bcm27xx/patches-5.10/950-0074-i2c-gpio-Also-set-bus-numbers-from-reg-property.patch b/target/linux/bcm27xx/patches-5.10/950-0074-i2c-gpio-Also-set-bus-numbers-from-reg-property.patch new file mode 100644 index 0000000000..a922328339 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0074-i2c-gpio-Also-set-bus-numbers-from-reg-property.patch @@ -0,0 +1,35 @@ +From 798407c217fee8f4869bf76d9cd2cda16f93e24f Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 20 Feb 2018 10:07:27 +0000 +Subject: [PATCH] i2c-gpio: Also set bus numbers from reg property + +I2C busses can be assigned specific bus numbers using aliases in +Device Tree - string properties where the name is the alias and the +value is the path to the node. The current DT parameter mechanism +does not allow property names to be derived from a parameter value +in any way, so it isn't possible to generate unique or matching +aliases for nodes from an overlay that can generate multiple +instances, e.g. i2c-gpio. + +Work around this limitation (at least temporarily) by allowing +the i2c adapter number to be initialised from the "reg" property +if present. + +Signed-off-by: Phil Elwell +--- + drivers/i2c/busses/i2c-gpio.c | 4 +++- + 1 file changed, 3 insertions(+), 1 deletion(-) + +--- a/drivers/i2c/busses/i2c-gpio.c ++++ b/drivers/i2c/busses/i2c-gpio.c +@@ -445,7 +445,9 @@ static int i2c_gpio_probe(struct platfor + adap->dev.parent = dev; + adap->dev.of_node = np; + +- adap->nr = pdev->id; ++ if (pdev->id != PLATFORM_DEVID_NONE || !pdev->dev.of_node || ++ of_property_read_u32(pdev->dev.of_node, "reg", &adap->nr)) ++ adap->nr = pdev->id; + ret = i2c_bit_add_numbered_bus(adap); + if (ret) + return ret; diff --git a/target/linux/bcm27xx/patches-5.10/950-0075-added-capture_clear-option-to-pps-gpio-via-dtoverlay.patch b/target/linux/bcm27xx/patches-5.10/950-0075-added-capture_clear-option-to-pps-gpio-via-dtoverlay.patch new file mode 100644 index 0000000000..80f68e9085 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0075-added-capture_clear-option-to-pps-gpio-via-dtoverlay.patch @@ -0,0 +1,21 @@ +From 781bfd769e192aa39ef93fa37c812af444a9cf93 Mon Sep 17 00:00:00 2001 +From: hdoverobinson +Date: Tue, 13 Mar 2018 06:58:39 -0400 +Subject: [PATCH] added capture_clear option to pps-gpio via dtoverlay + (#2433) + +--- + drivers/pps/clients/pps-gpio.c | 2 ++ + 1 file changed, 2 insertions(+) + +--- a/drivers/pps/clients/pps-gpio.c ++++ b/drivers/pps/clients/pps-gpio.c +@@ -145,6 +145,8 @@ static int pps_gpio_setup(struct platfor + + if (of_property_read_bool(np, "assert-falling-edge")) + data->assert_falling_edge = true; ++ if (of_property_read_bool(np, "capture-clear")) ++ data->capture_clear = true; + return 0; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0076-lan78xx-Read-initial-EEE-status-from-DT.patch b/target/linux/bcm27xx/patches-5.10/950-0076-lan78xx-Read-initial-EEE-status-from-DT.patch new file mode 100644 index 0000000000..56c0f537fe --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0076-lan78xx-Read-initial-EEE-status-from-DT.patch @@ -0,0 +1,40 @@ +From 1fbf5f72be35918230b0bbdff3bcf44318f1374a Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 9 Mar 2018 12:01:00 +0000 +Subject: [PATCH] lan78xx: Read initial EEE status from DT + +Add two new DT properties: +* microchip,eee-enabled - a boolean to enable EEE +* microchip,tx-lpi-timer - time in microseconds to wait before entering + low power state + +Signed-off-by: Phil Elwell +--- + drivers/net/usb/lan78xx.c | 16 ++++++++++++++++ + 1 file changed, 16 insertions(+) + +--- a/drivers/net/usb/lan78xx.c ++++ b/drivers/net/usb/lan78xx.c +@@ -2635,6 +2635,22 @@ static int lan78xx_open(struct net_devic + + netif_dbg(dev, ifup, dev->net, "phy initialised successfully"); + ++ if (of_property_read_bool(dev->udev->dev.of_node, ++ "microchip,eee-enabled")) { ++ struct ethtool_eee edata; ++ memset(&edata, 0, sizeof(edata)); ++ edata.cmd = ETHTOOL_SEEE; ++ edata.advertised = ADVERTISED_1000baseT_Full | ++ ADVERTISED_100baseT_Full; ++ edata.eee_enabled = true; ++ edata.tx_lpi_enabled = true; ++ if (of_property_read_u32(dev->udev->dev.of_node, ++ "microchip,tx-lpi-timer", ++ &edata.tx_lpi_timer)) ++ edata.tx_lpi_timer = 600; /* non-aggressive */ ++ (void)lan78xx_set_eee(net, &edata); ++ } ++ + /* for Link Check */ + if (dev->urb_intr) { + ret = usb_submit_urb(dev->urb_intr, GFP_KERNEL); diff --git a/target/linux/bcm27xx/patches-5.10/950-0077-hid-Reduce-default-mouse-polling-interval-to-60Hz.patch b/target/linux/bcm27xx/patches-5.10/950-0077-hid-Reduce-default-mouse-polling-interval-to-60Hz.patch new file mode 100644 index 0000000000..2c17fb0aa6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0077-hid-Reduce-default-mouse-polling-interval-to-60Hz.patch @@ -0,0 +1,32 @@ +From 32648d9e5440756f571bff70e8c49069dbba5137 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Mon, 14 Jul 2014 22:02:09 +0100 +Subject: [PATCH] hid: Reduce default mouse polling interval to 60Hz + +Reduces overhead when using X +--- + drivers/hid/usbhid/hid-core.c | 6 ++++-- + 1 file changed, 4 insertions(+), 2 deletions(-) + +--- a/drivers/hid/usbhid/hid-core.c ++++ b/drivers/hid/usbhid/hid-core.c +@@ -45,7 +45,7 @@ + * Module parameters. + */ + +-static unsigned int hid_mousepoll_interval; ++static unsigned int hid_mousepoll_interval = ~0; + module_param_named(mousepoll, hid_mousepoll_interval, uint, 0644); + MODULE_PARM_DESC(mousepoll, "Polling interval of mice"); + +@@ -1114,7 +1114,9 @@ static int usbhid_start(struct hid_devic + */ + switch (hid->collection->usage) { + case HID_GD_MOUSE: +- if (hid_mousepoll_interval > 0) ++ if (hid_mousepoll_interval == ~0 && interval < 16) ++ interval = 16; ++ else if (hid_mousepoll_interval != ~0 && hid_mousepoll_interval != 0) + interval = hid_mousepoll_interval; + break; + case HID_GD_JOYSTICK: diff --git a/target/linux/bcm27xx/patches-5.10/950-0078-Add-ability-to-export-gpio-used-by-gpio-poweroff.patch b/target/linux/bcm27xx/patches-5.10/950-0078-Add-ability-to-export-gpio-used-by-gpio-poweroff.patch new file mode 100644 index 0000000000..a8aa6fe882 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0078-Add-ability-to-export-gpio-used-by-gpio-poweroff.patch @@ -0,0 +1,57 @@ +From a8d5d1b7fbc78132f5def4b8af4f221df83df04e Mon Sep 17 00:00:00 2001 +From: Nick Bulleid +Date: Thu, 10 May 2018 21:57:02 +0100 +Subject: [PATCH] Add ability to export gpio used by gpio-poweroff + +Signed-off-by: Nick Bulleid + +Added export feature to gpio-poweroff documentation + +Signed-off-by: Nick Bulleid +--- + .../devicetree/bindings/power/reset/gpio-poweroff.txt | 1 + + drivers/power/reset/gpio-poweroff.c | 9 +++++++++ + 2 files changed, 10 insertions(+) + +--- a/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt ++++ b/Documentation/devicetree/bindings/power/reset/gpio-poweroff.txt +@@ -31,6 +31,7 @@ Optional properties: + - inactive-delay-ms: Delay (default 100) to wait after driving gpio inactive + - timeout-ms: Time to wait before asserting a WARN_ON(1). If nothing is + specified, 3000 ms is used. ++- export : Export the GPIO line to the sysfs system + + Examples: + +--- a/drivers/power/reset/gpio-poweroff.c ++++ b/drivers/power/reset/gpio-poweroff.c +@@ -51,6 +51,7 @@ static int gpio_poweroff_probe(struct pl + bool input = false; + enum gpiod_flags flags; + bool force = false; ++ bool export = false; + + /* If a pm_power_off function has already been added, leave it alone */ + force = of_property_read_bool(pdev->dev.of_node, "force"); +@@ -76,6 +77,12 @@ static int gpio_poweroff_probe(struct pl + if (IS_ERR(reset_gpio)) + return PTR_ERR(reset_gpio); + ++ export = of_property_read_bool(pdev->dev.of_node, "export"); ++ if (export) { ++ gpiod_export(reset_gpio, false); ++ gpiod_export_link(&pdev->dev, "poweroff-gpio", reset_gpio); ++ } ++ + pm_power_off = &gpio_poweroff_do_poweroff; + return 0; + } +@@ -85,6 +92,8 @@ static int gpio_poweroff_remove(struct p + if (pm_power_off == &gpio_poweroff_do_poweroff) + pm_power_off = NULL; + ++ gpiod_unexport(reset_gpio); ++ + return 0; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0079-firmware-raspberrypi-Notify-firmware-of-a-reboot.patch b/target/linux/bcm27xx/patches-5.10/950-0079-firmware-raspberrypi-Notify-firmware-of-a-reboot.patch new file mode 100644 index 0000000000..bdcf5c4b42 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0079-firmware-raspberrypi-Notify-firmware-of-a-reboot.patch @@ -0,0 +1,84 @@ +From bf6b5dbb7c8423b9d6bdfec21a9122691f2587d9 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Sat, 12 May 2018 21:35:43 +0100 +Subject: [PATCH] firmware/raspberrypi: Notify firmware of a reboot + +Register for reboot notifications, sending RPI_FIRMWARE_NOTIFY_REBOOT +over the mailbox interface on reception. + +Signed-off-by: Phil Elwell +--- + drivers/firmware/raspberrypi.c | 40 +++++++++++++++++++++++++++++++++- + 1 file changed, 39 insertions(+), 1 deletion(-) + +--- a/drivers/firmware/raspberrypi.c ++++ b/drivers/firmware/raspberrypi.c +@@ -11,6 +11,7 @@ + #include + #include + #include ++#include + #include + #include + +@@ -177,6 +178,26 @@ int rpi_firmware_property(struct rpi_fir + } + EXPORT_SYMBOL_GPL(rpi_firmware_property); + ++static int rpi_firmware_notify_reboot(struct notifier_block *nb, ++ unsigned long action, ++ void *data) ++{ ++ struct rpi_firmware *fw; ++ struct platform_device *pdev = g_pdev; ++ ++ if (!pdev) ++ return 0; ++ ++ fw = platform_get_drvdata(pdev); ++ if (!fw) ++ return 0; ++ ++ (void)rpi_firmware_property(fw, RPI_FIRMWARE_NOTIFY_REBOOT, ++ 0, 0); ++ ++ return 0; ++} ++ + static void + rpi_firmware_print_firmware_revision(struct rpi_firmware *fw) + { +@@ -318,15 +339,32 @@ static struct platform_driver rpi_firmwa + .remove = rpi_firmware_remove, + }; + ++static struct notifier_block rpi_firmware_reboot_notifier = { ++ .notifier_call = rpi_firmware_notify_reboot, ++}; ++ + static int __init rpi_firmware_init(void) + { +- return platform_driver_register(&rpi_firmware_driver); ++ int ret = register_reboot_notifier(&rpi_firmware_reboot_notifier); ++ if (ret) ++ goto out1; ++ ret = platform_driver_register(&rpi_firmware_driver); ++ if (ret) ++ goto out2; ++ ++ return 0; ++ ++out2: ++ unregister_reboot_notifier(&rpi_firmware_reboot_notifier); ++out1: ++ return ret; + } + subsys_initcall(rpi_firmware_init); + + static void __init rpi_firmware_exit(void) + { + platform_driver_unregister(&rpi_firmware_driver); ++ unregister_reboot_notifier(&rpi_firmware_reboot_notifier); + } + module_exit(rpi_firmware_exit); + diff --git a/target/linux/bcm27xx/patches-5.10/950-0080-irqchip-irq-bcm2835-Calc.-FIQ_START-at-boot-time.patch b/target/linux/bcm27xx/patches-5.10/950-0080-irqchip-irq-bcm2835-Calc.-FIQ_START-at-boot-time.patch new file mode 100644 index 0000000000..c02f5f699b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0080-irqchip-irq-bcm2835-Calc.-FIQ_START-at-boot-time.patch @@ -0,0 +1,66 @@ +From 35a38d723d9cd61be4c39defad4e44b1a6acc4b8 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 14 Jun 2018 11:21:04 +0100 +Subject: [PATCH] irqchip: irq-bcm2835: Calc. FIQ_START at boot-time + +ad83c7cb2f37 ("irqchip/irq-bcm2836: Add support for DT interrupt polarity") +changed the way that the BCM2836/7 local interrupts are mapped; instead +of being pre-mapped they are now mapped on-demand. A side effect of this +change is that the call to irq_of_parse_and_map from armctrl_of_init +creates a new mapping, forming a gap between the IRQs and the FIQs. This + gap breaks the FIQ<->IRQ mapping which up to now has been done by assuming: + +1) that the value of FIQ_START is the same as the number of normal IRQs +that will be mapped (still true), and + +2) that this value is also the offset between an IRQ and its equivalent +FIQ (which is no longer the case). + +Remove both assumptions by measuring the interval between the last IRQ +and the last FIQ, passing it as the parameter to init_FIQ(). + +Fixes: https://github.com/raspberrypi/linux/issues/2432 + +Signed-off-by: Phil Elwell +--- + drivers/irqchip/irq-bcm2835.c | 8 ++++---- + 1 file changed, 4 insertions(+), 4 deletions(-) + +--- a/drivers/irqchip/irq-bcm2835.c ++++ b/drivers/irqchip/irq-bcm2835.c +@@ -74,8 +74,6 @@ + #define NR_BANKS 3 + #define IRQS_PER_BANK 32 + #define NUMBER_IRQS MAKE_HWIRQ(NR_BANKS, 0) +-#undef FIQ_START +-#define FIQ_START (NR_IRQS_BANK0 + MAKE_HWIRQ(NR_BANKS - 1, 0)) + + static const int reg_pending[] __initconst = { 0x00, 0x04, 0x08 }; + static const int reg_enable[] __initconst = { 0x18, 0x10, 0x14 }; +@@ -203,7 +201,7 @@ static int __init armctrl_of_init(struct + bool is_2836) + { + void __iomem *base; +- int irq, b, i; ++ int irq = 0, last_irq, b, i; + u32 reg; + + base = of_iomap(node, 0); +@@ -243,6 +241,8 @@ static int __init armctrl_of_init(struct + pr_err(FW_BUG "Bootloader left fiq enabled\n"); + } + ++ last_irq = irq; ++ + if (is_2836) { + int parent_irq = irq_of_parse_and_map(node, 0); + +@@ -273,7 +273,7 @@ static int __init armctrl_of_init(struct + } + } + #ifndef CONFIG_ARM64 +- init_FIQ(FIQ_START); ++ init_FIQ(irq - last_irq); + #endif + + return 0; diff --git a/target/linux/bcm27xx/patches-5.10/950-0081-of-configfs-Use-of_overlay_fdt_apply-API-call.patch b/target/linux/bcm27xx/patches-5.10/950-0081-of-configfs-Use-of_overlay_fdt_apply-API-call.patch new file mode 100644 index 0000000000..f707f220a2 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0081-of-configfs-Use-of_overlay_fdt_apply-API-call.patch @@ -0,0 +1,114 @@ +From 342afb4c37627f9d8e9d5bb07b3182a5c412c75e Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 14 Jun 2018 15:07:26 +0100 +Subject: [PATCH] of: configfs: Use of_overlay_fdt_apply API call + +The published API to the dynamic overlay application mechanism now +takes a Flattened Device Tree blob as input so that it can manage the +lifetime of the unflattened tree. Conveniently, the new API call - +of_overlay_fdt_apply - is virtually a drop-in replacement for +create_overlay, which can now be deleted. + +Signed-off-by: Phil Elwell +--- + drivers/of/configfs.c | 47 +++++++------------------------------------ + 1 file changed, 7 insertions(+), 40 deletions(-) + +--- a/drivers/of/configfs.c ++++ b/drivers/of/configfs.c +@@ -40,41 +40,6 @@ struct cfs_overlay_item { + int dtbo_size; + }; + +-static int create_overlay(struct cfs_overlay_item *overlay, void *blob) +-{ +- int err; +- +- /* unflatten the tree */ +- of_fdt_unflatten_tree(blob, NULL, &overlay->overlay); +- if (overlay->overlay == NULL) { +- pr_err("%s: failed to unflatten tree\n", __func__); +- err = -EINVAL; +- goto out_err; +- } +- pr_debug("%s: unflattened OK\n", __func__); +- +- /* mark it as detached */ +- of_node_set_flag(overlay->overlay, OF_DETACHED); +- +- /* perform resolution */ +- err = of_resolve_phandles(overlay->overlay); +- if (err != 0) { +- pr_err("%s: Failed to resolve tree\n", __func__); +- goto out_err; +- } +- pr_debug("%s: resolved OK\n", __func__); +- +- err = of_overlay_apply(overlay->overlay, &overlay->ov_id); +- if (err < 0) { +- pr_err("%s: Failed to create overlay (err=%d)\n", +- __func__, err); +- goto out_err; +- } +- +-out_err: +- return err; +-} +- + static inline struct cfs_overlay_item *to_cfs_overlay_item( + struct config_item *item) + { +@@ -115,7 +80,8 @@ static ssize_t cfs_overlay_item_path_sto + if (err != 0) + goto out_err; + +- err = create_overlay(overlay, (void *)overlay->fw->data); ++ err = of_overlay_fdt_apply((void *)overlay->fw->data, ++ (u32)overlay->fw->size, &overlay->ov_id); + if (err != 0) + goto out_err; + +@@ -136,7 +102,7 @@ static ssize_t cfs_overlay_item_status_s + struct cfs_overlay_item *overlay = to_cfs_overlay_item(item); + + return sprintf(page, "%s\n", +- overlay->ov_id >= 0 ? "applied" : "unapplied"); ++ overlay->ov_id > 0 ? "applied" : "unapplied"); + } + + CONFIGFS_ATTR(cfs_overlay_item_, path); +@@ -188,7 +154,8 @@ ssize_t cfs_overlay_item_dtbo_write(stru + + overlay->dtbo_size = count; + +- err = create_overlay(overlay, overlay->dtbo); ++ err = of_overlay_fdt_apply(overlay->dtbo, overlay->dtbo_size, ++ &overlay->ov_id); + if (err != 0) + goto out_err; + +@@ -198,6 +165,7 @@ out_err: + kfree(overlay->dtbo); + overlay->dtbo = NULL; + overlay->dtbo_size = 0; ++ overlay->ov_id = 0; + + return err; + } +@@ -213,7 +181,7 @@ static void cfs_overlay_release(struct c + { + struct cfs_overlay_item *overlay = to_cfs_overlay_item(item); + +- if (overlay->ov_id >= 0) ++ if (overlay->ov_id > 0) + of_overlay_remove(&overlay->ov_id); + if (overlay->fw) + release_firmware(overlay->fw); +@@ -241,7 +209,6 @@ static struct config_item *cfs_overlay_g + overlay = kzalloc(sizeof(*overlay), GFP_KERNEL); + if (!overlay) + return ERR_PTR(-ENOMEM); +- overlay->ov_id = -1; + + config_item_init_type_name(&overlay->item, name, &cfs_overlay_type); + return &overlay->item; diff --git a/target/linux/bcm27xx/patches-5.10/950-0082-net-lan78xx-Disable-TCP-Segmentation-Offload-TSO.patch b/target/linux/bcm27xx/patches-5.10/950-0082-net-lan78xx-Disable-TCP-Segmentation-Offload-TSO.patch new file mode 100644 index 0000000000..232e4d4336 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0082-net-lan78xx-Disable-TCP-Segmentation-Offload-TSO.patch @@ -0,0 +1,56 @@ +From 42606db546588b0e0b8084466b9b31ec111640a4 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 13 Jun 2018 15:21:10 +0100 +Subject: [PATCH] net: lan78xx: Disable TCP Segmentation Offload (TSO) + +TSO seems to be having issues when packets are dropped and the +remote end uses Selective Acknowledge (SACK) to denote that +data is missing. The missing data is never resent, so the +connection eventually stalls. + +There is a module parameter of enable_tso added to allow +further debugging without forcing a rebuild of the kernel. + +https://github.com/raspberrypi/linux/issues/2449 +https://github.com/raspberrypi/linux/issues/2482 + +Signed-off-by: Dave Stevenson +--- + drivers/net/usb/lan78xx.c | 19 +++++++++++++++++-- + 1 file changed, 17 insertions(+), 2 deletions(-) + +--- a/drivers/net/usb/lan78xx.c ++++ b/drivers/net/usb/lan78xx.c +@@ -425,6 +425,15 @@ static int msg_level = -1; + module_param(msg_level, int, 0); + MODULE_PARM_DESC(msg_level, "Override default message level"); + ++/* TSO seems to be having some issue with Selective Acknowledge (SACK) that ++ * results in lost data never being retransmitted. ++ * Disable it by default now, but adds a module parameter to enable it for ++ * debug purposes (the full cause is not currently understood). ++ */ ++static bool enable_tso; ++module_param(enable_tso, bool, 0644); ++MODULE_PARM_DESC(enable_tso, "Enables TCP segmentation offload"); ++ + static int lan78xx_read_reg(struct lan78xx_net *dev, u32 index, u32 *data) + { + u32 *buf = kmalloc(sizeof(u32), GFP_KERNEL); +@@ -2917,8 +2926,14 @@ static int lan78xx_bind(struct lan78xx_n + if (DEFAULT_RX_CSUM_ENABLE) + dev->net->features |= NETIF_F_RXCSUM; + +- if (DEFAULT_TSO_CSUM_ENABLE) +- dev->net->features |= NETIF_F_TSO | NETIF_F_TSO6 | NETIF_F_SG; ++ if (DEFAULT_TSO_CSUM_ENABLE) { ++ dev->net->features |= NETIF_F_SG; ++ /* Use module parameter to control TCP segmentation offload as ++ * it appears to cause issues. ++ */ ++ if (enable_tso) ++ dev->net->features |= NETIF_F_TSO | NETIF_F_TSO6; ++ } + + if (DEFAULT_VLAN_RX_OFFLOAD) + dev->net->features |= NETIF_F_HW_VLAN_CTAG_RX; diff --git a/target/linux/bcm27xx/patches-5.10/950-0083-lan78xx-Move-enabling-of-EEE-into-PHY-init-code.patch b/target/linux/bcm27xx/patches-5.10/950-0083-lan78xx-Move-enabling-of-EEE-into-PHY-init-code.patch new file mode 100644 index 0000000000..b69c89febb --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0083-lan78xx-Move-enabling-of-EEE-into-PHY-init-code.patch @@ -0,0 +1,64 @@ +From c6edee4700821a65c9d94ac8e16b488fc652efd8 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 5 Apr 2018 14:46:11 +0100 +Subject: [PATCH] lan78xx: Move enabling of EEE into PHY init code + +Enable EEE mode as soon as possible after connecting to the PHY, and +before phy_start. This avoids a second link negotiation, which speeds +up booting and stops the interface failing to become ready. + +See: https://github.com/raspberrypi/linux/issues/2437 + +Signed-off-by: Phil Elwell +--- + drivers/net/usb/lan78xx.c | 32 ++++++++++++++++---------------- + 1 file changed, 16 insertions(+), 16 deletions(-) + +--- a/drivers/net/usb/lan78xx.c ++++ b/drivers/net/usb/lan78xx.c +@@ -2167,6 +2167,22 @@ static int lan78xx_phy_init(struct lan78 + mii_adv_to_linkmode_adv_t(fc, mii_adv); + linkmode_or(phydev->advertising, fc, phydev->advertising); + ++ if (of_property_read_bool(dev->udev->dev.of_node, ++ "microchip,eee-enabled")) { ++ struct ethtool_eee edata; ++ memset(&edata, 0, sizeof(edata)); ++ edata.cmd = ETHTOOL_SEEE; ++ edata.advertised = ADVERTISED_1000baseT_Full | ++ ADVERTISED_100baseT_Full; ++ edata.eee_enabled = true; ++ edata.tx_lpi_enabled = true; ++ if (of_property_read_u32(dev->udev->dev.of_node, ++ "microchip,tx-lpi-timer", ++ &edata.tx_lpi_timer)) ++ edata.tx_lpi_timer = 600; /* non-aggressive */ ++ (void)lan78xx_set_eee(dev->net, &edata); ++ } ++ + if (phydev->mdio.dev.of_node) { + u32 reg; + int len; +@@ -2644,22 +2660,6 @@ static int lan78xx_open(struct net_devic + + netif_dbg(dev, ifup, dev->net, "phy initialised successfully"); + +- if (of_property_read_bool(dev->udev->dev.of_node, +- "microchip,eee-enabled")) { +- struct ethtool_eee edata; +- memset(&edata, 0, sizeof(edata)); +- edata.cmd = ETHTOOL_SEEE; +- edata.advertised = ADVERTISED_1000baseT_Full | +- ADVERTISED_100baseT_Full; +- edata.eee_enabled = true; +- edata.tx_lpi_enabled = true; +- if (of_property_read_u32(dev->udev->dev.of_node, +- "microchip,tx-lpi-timer", +- &edata.tx_lpi_timer)) +- edata.tx_lpi_timer = 600; /* non-aggressive */ +- (void)lan78xx_set_eee(net, &edata); +- } +- + /* for Link Check */ + if (dev->urb_intr) { + ret = usb_submit_urb(dev->urb_intr, GFP_KERNEL); diff --git a/target/linux/bcm27xx/patches-5.10/950-0084-Add-rpi-poe-fan-driver.patch b/target/linux/bcm27xx/patches-5.10/950-0084-Add-rpi-poe-fan-driver.patch new file mode 100644 index 0000000000..a93529e4ba --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0084-Add-rpi-poe-fan-driver.patch @@ -0,0 +1,581 @@ +From 079bce6210d997fda44d6143b4b394173360bef1 Mon Sep 17 00:00:00 2001 +From: Serge Schneider +Date: Mon, 9 Jul 2018 12:54:25 +0100 +Subject: [PATCH] Add rpi-poe-fan driver + +Signed-off-by: Serge Schneider + +PoE HAT driver cleanup + +* Fix undeclared variable in rpi_poe_fan_suspend +* Add SPDX-License-Identifier +* Expand PoE acronym in Kconfig help +* Give clearer error message on of_property_count_u32_elems fail +* Add documentation +* Add vendor to of_device_id compatible string. +* Rename m_data_s struct to fw_data_s +* Fix typos + +Fixes: #2665 + +Signed-off-by: Serge Schneider + +rpi-poe-fan: fix def_pwm1 writes + +Signed-off-by: Serge Schneider +--- + .../devicetree/bindings/hwmon/rpi-poe-fan.txt | 55 +++ + Documentation/hwmon/rpi-poe-fan | 15 + + drivers/hwmon/Kconfig | 11 + + drivers/hwmon/Makefile | 1 + + drivers/hwmon/rpi-poe-fan.c | 436 ++++++++++++++++++ + 5 files changed, 518 insertions(+) + create mode 100644 Documentation/devicetree/bindings/hwmon/rpi-poe-fan.txt + create mode 100644 Documentation/hwmon/rpi-poe-fan + create mode 100644 drivers/hwmon/rpi-poe-fan.c + +--- /dev/null ++++ b/Documentation/devicetree/bindings/hwmon/rpi-poe-fan.txt +@@ -0,0 +1,55 @@ ++Bindings for the Raspberry Pi PoE HAT fan ++ ++Required properties: ++- compatible : "raspberrypi,rpi-poe-fan" ++- firmware : Reference to the RPi firmware device node ++- pwms : the PWM that is used to control the PWM fan ++- cooling-levels : PWM duty cycle values in a range from 0 to 255 ++ which correspond to thermal cooling states ++ ++Example: ++ fan0: rpi-poe-fan@0 { ++ compatible = "raspberrypi,rpi-poe-fan"; ++ firmware = <&firmware>; ++ cooling-min-state = <0>; ++ cooling-max-state = <3>; ++ #cooling-cells = <2>; ++ cooling-levels = <0 50 150 255>; ++ status = "okay"; ++ }; ++ ++ thermal-zones { ++ cpu_thermal: cpu-thermal { ++ trips { ++ threshold: trip-point@0 { ++ temperature = <45000>; ++ hysteresis = <5000>; ++ type = "active"; ++ }; ++ target: trip-point@1 { ++ temperature = <50000>; ++ hysteresis = <2000>; ++ type = "active"; ++ }; ++ cpu_hot: cpu_hot@0 { ++ temperature = <55000>; ++ hysteresis = <2000>; ++ type = "active"; ++ }; ++ }; ++ cooling-maps { ++ map0 { ++ trip = <&threshold>; ++ cooling-device = <&fan0 0 1>; ++ }; ++ map1 { ++ trip = <&target>; ++ cooling-device = <&fan0 1 2>; ++ }; ++ map2 { ++ trip = <&cpu_hot>; ++ cooling-device = <&fan0 2 3>; ++ }; ++ }; ++ }; ++ }; +--- /dev/null ++++ b/Documentation/hwmon/rpi-poe-fan +@@ -0,0 +1,15 @@ ++Kernel driver rpi-poe-fan ++===================== ++ ++This driver enables the use of the Raspberry Pi PoE HAT fan. ++ ++Author: Serge Schneider ++ ++Description ++----------- ++ ++The driver implements a simple interface for driving the Raspberry Pi PoE ++(Power over Ethernet) HAT fan. The driver passes commands to the Raspberry Pi ++firmware through the mailbox property interface. The firmware then forwards ++the commands to the board over I2C on the ID_EEPROM pins. The driver exposes ++the fan to the user space through the hwmon sysfs interface. +--- a/drivers/hwmon/Kconfig ++++ b/drivers/hwmon/Kconfig +@@ -1489,6 +1489,17 @@ config SENSORS_RASPBERRYPI_HWMON + This driver can also be built as a module. If so, the module + will be called raspberrypi-hwmon. + ++config SENSORS_RPI_POE_FAN ++ tristate "Raspberry Pi PoE HAT fan" ++ depends on RASPBERRYPI_FIRMWARE ++ depends on THERMAL || THERMAL=n ++ help ++ If you say yes here you get support for Raspberry Pi PoE (Power over ++ Ethernet) HAT fan. ++ ++ This driver can also be built as a module. If so, the module ++ will be called rpi-poe-fan. ++ + config SENSORS_SL28CPLD + tristate "Kontron sl28cpld hardware monitoring driver" + depends on MFD_SL28CPLD || COMPILE_TEST +--- a/drivers/hwmon/Makefile ++++ b/drivers/hwmon/Makefile +@@ -157,6 +157,7 @@ obj-$(CONFIG_SENSORS_PCF8591) += pcf8591 + obj-$(CONFIG_SENSORS_POWR1220) += powr1220.o + obj-$(CONFIG_SENSORS_PWM_FAN) += pwm-fan.o + obj-$(CONFIG_SENSORS_RASPBERRYPI_HWMON) += raspberrypi-hwmon.o ++obj-$(CONFIG_SENSORS_RPI_POE_FAN) += rpi-poe-fan.o + obj-$(CONFIG_SENSORS_S3C) += s3c-hwmon.o + obj-$(CONFIG_SENSORS_SCH56XX_COMMON)+= sch56xx-common.o + obj-$(CONFIG_SENSORS_SCH5627) += sch5627.o +--- /dev/null ++++ b/drivers/hwmon/rpi-poe-fan.c +@@ -0,0 +1,436 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * rpi-poe-fan.c - Hwmon driver for Raspberry Pi PoE HAT fan. ++ * ++ * Copyright (C) 2018 Raspberry Pi (Trading) Ltd. ++ * Based on pwm-fan.c by Kamil Debski ++ * ++ * Author: Serge Schneider ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define MAX_PWM 255 ++ ++#define POE_CUR_PWM 0x0 ++#define POE_DEF_PWM 0x1 ++ ++struct rpi_poe_fan_ctx { ++ struct mutex lock; ++ struct rpi_firmware *fw; ++ unsigned int pwm_value; ++ unsigned int def_pwm_value; ++ unsigned int rpi_poe_fan_state; ++ unsigned int rpi_poe_fan_max_state; ++ unsigned int *rpi_poe_fan_cooling_levels; ++ struct thermal_cooling_device *cdev; ++ struct notifier_block nb; ++}; ++ ++struct fw_tag_data_s{ ++ u32 reg; ++ u32 val; ++ u32 ret; ++}; ++ ++static int write_reg(struct rpi_firmware *fw, u32 reg, u32 *val){ ++ struct fw_tag_data_s fw_tag_data = { ++ .reg = reg, ++ .val = *val ++ }; ++ int ret; ++ ret = rpi_firmware_property(fw, RPI_FIRMWARE_SET_POE_HAT_VAL, ++ &fw_tag_data, sizeof(fw_tag_data)); ++ if (ret) { ++ return ret; ++ } else if (fw_tag_data.ret) { ++ return -EIO; ++ } ++ return 0; ++} ++ ++static int read_reg(struct rpi_firmware *fw, u32 reg, u32 *val){ ++ struct fw_tag_data_s fw_tag_data = { ++ .reg = reg, ++ }; ++ int ret; ++ ret = rpi_firmware_property(fw, RPI_FIRMWARE_GET_POE_HAT_VAL, ++ &fw_tag_data, sizeof(fw_tag_data)); ++ if (ret) { ++ return ret; ++ } else if (fw_tag_data.ret) { ++ return -EIO; ++ } ++ *val = fw_tag_data.val; ++ return 0; ++} ++ ++static int rpi_poe_reboot(struct notifier_block *nb, unsigned long code, ++ void *unused) ++{ ++ struct rpi_poe_fan_ctx *ctx = container_of(nb, struct rpi_poe_fan_ctx, ++ nb); ++ ++ if (ctx->pwm_value != ctx->def_pwm_value) ++ write_reg(ctx->fw, POE_CUR_PWM, &ctx->def_pwm_value); ++ ++ return NOTIFY_DONE; ++} ++ ++static int __set_pwm(struct rpi_poe_fan_ctx *ctx, u32 pwm) ++{ ++ int ret = 0; ++ ++ mutex_lock(&ctx->lock); ++ if (ctx->pwm_value == pwm) ++ goto exit_set_pwm_err; ++ ++ ret = write_reg(ctx->fw, POE_CUR_PWM, &pwm); ++ if (!ret) ++ ctx->pwm_value = pwm; ++exit_set_pwm_err: ++ mutex_unlock(&ctx->lock); ++ return ret; ++} ++ ++static int __set_def_pwm(struct rpi_poe_fan_ctx *ctx, u32 def_pwm) ++{ ++ int ret = 0; ++ mutex_lock(&ctx->lock); ++ if (ctx->def_pwm_value == def_pwm) ++ goto exit_set_def_pwm_err; ++ ++ ret = write_reg(ctx->fw, POE_DEF_PWM, &def_pwm); ++ if (!ret) ++ ctx->def_pwm_value = def_pwm; ++exit_set_def_pwm_err: ++ mutex_unlock(&ctx->lock); ++ return ret; ++} ++ ++static void rpi_poe_fan_update_state(struct rpi_poe_fan_ctx *ctx, ++ unsigned long pwm) ++{ ++ int i; ++ ++ for (i = 0; i < ctx->rpi_poe_fan_max_state; ++i) ++ if (pwm < ctx->rpi_poe_fan_cooling_levels[i + 1]) ++ break; ++ ++ ctx->rpi_poe_fan_state = i; ++} ++ ++static ssize_t set_pwm(struct device *dev, struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++ struct rpi_poe_fan_ctx *ctx = dev_get_drvdata(dev); ++ unsigned long pwm; ++ int ret; ++ ++ if (kstrtoul(buf, 10, &pwm) || pwm > MAX_PWM) ++ return -EINVAL; ++ ++ ret = __set_pwm(ctx, pwm); ++ if (ret) ++ return ret; ++ ++ rpi_poe_fan_update_state(ctx, pwm); ++ return count; ++} ++ ++static ssize_t set_def_pwm(struct device *dev, struct device_attribute *attr, ++ const char *buf, size_t count) ++{ ++ struct rpi_poe_fan_ctx *ctx = dev_get_drvdata(dev); ++ unsigned long def_pwm; ++ int ret; ++ ++ if (kstrtoul(buf, 10, &def_pwm) || def_pwm > MAX_PWM) ++ return -EINVAL; ++ ++ ret = __set_def_pwm(ctx, def_pwm); ++ if (ret) ++ return ret; ++ return count; ++} ++ ++static ssize_t show_pwm(struct device *dev, ++ struct device_attribute *attr, char *buf) ++{ ++ struct rpi_poe_fan_ctx *ctx = dev_get_drvdata(dev); ++ ++ return sprintf(buf, "%u\n", ctx->pwm_value); ++} ++ ++static ssize_t show_def_pwm(struct device *dev, ++ struct device_attribute *attr, char *buf) ++{ ++ struct rpi_poe_fan_ctx *ctx = dev_get_drvdata(dev); ++ ++ return sprintf(buf, "%u\n", ctx->def_pwm_value); ++} ++ ++ ++static SENSOR_DEVICE_ATTR(pwm1, 0644, show_pwm, set_pwm, 0); ++static SENSOR_DEVICE_ATTR(def_pwm1, 0644, show_def_pwm, set_def_pwm, 1); ++ ++static struct attribute *rpi_poe_fan_attrs[] = { ++ &sensor_dev_attr_pwm1.dev_attr.attr, ++ &sensor_dev_attr_def_pwm1.dev_attr.attr, ++ NULL, ++}; ++ ++ATTRIBUTE_GROUPS(rpi_poe_fan); ++ ++/* thermal cooling device callbacks */ ++static int rpi_poe_fan_get_max_state(struct thermal_cooling_device *cdev, ++ unsigned long *state) ++{ ++ struct rpi_poe_fan_ctx *ctx = cdev->devdata; ++ ++ if (!ctx) ++ return -EINVAL; ++ ++ *state = ctx->rpi_poe_fan_max_state; ++ ++ return 0; ++} ++ ++static int rpi_poe_fan_get_cur_state(struct thermal_cooling_device *cdev, ++ unsigned long *state) ++{ ++ struct rpi_poe_fan_ctx *ctx = cdev->devdata; ++ ++ if (!ctx) ++ return -EINVAL; ++ ++ *state = ctx->rpi_poe_fan_state; ++ ++ return 0; ++} ++ ++static int rpi_poe_fan_set_cur_state(struct thermal_cooling_device *cdev, ++ unsigned long state) ++{ ++ struct rpi_poe_fan_ctx *ctx = cdev->devdata; ++ int ret; ++ ++ if (!ctx || (state > ctx->rpi_poe_fan_max_state)) ++ return -EINVAL; ++ ++ if (state == ctx->rpi_poe_fan_state) ++ return 0; ++ ++ ret = __set_pwm(ctx, ctx->rpi_poe_fan_cooling_levels[state]); ++ if (ret) { ++ dev_err(&cdev->device, "Cannot set pwm!\n"); ++ return ret; ++ } ++ ++ ctx->rpi_poe_fan_state = state; ++ ++ return ret; ++} ++ ++static const struct thermal_cooling_device_ops rpi_poe_fan_cooling_ops = { ++ .get_max_state = rpi_poe_fan_get_max_state, ++ .get_cur_state = rpi_poe_fan_get_cur_state, ++ .set_cur_state = rpi_poe_fan_set_cur_state, ++}; ++ ++static int rpi_poe_fan_of_get_cooling_data(struct device *dev, ++ struct rpi_poe_fan_ctx *ctx) ++{ ++ struct device_node *np = dev->of_node; ++ int num, i, ret; ++ ++ if (!of_find_property(np, "cooling-levels", NULL)) ++ return 0; ++ ++ ret = of_property_count_u32_elems(np, "cooling-levels"); ++ if (ret <= 0) { ++ dev_err(dev, "cooling-levels property missing or invalid: %d\n", ++ ret); ++ return ret ? : -EINVAL; ++ } ++ ++ num = ret; ++ ctx->rpi_poe_fan_cooling_levels = devm_kzalloc(dev, num * sizeof(u32), ++ GFP_KERNEL); ++ if (!ctx->rpi_poe_fan_cooling_levels) ++ return -ENOMEM; ++ ++ ret = of_property_read_u32_array(np, "cooling-levels", ++ ctx->rpi_poe_fan_cooling_levels, num); ++ if (ret) { ++ dev_err(dev, "Property 'cooling-levels' cannot be read!\n"); ++ return ret; ++ } ++ ++ for (i = 0; i < num; i++) { ++ if (ctx->rpi_poe_fan_cooling_levels[i] > MAX_PWM) { ++ dev_err(dev, "PWM fan state[%d]:%d > %d\n", i, ++ ctx->rpi_poe_fan_cooling_levels[i], MAX_PWM); ++ return -EINVAL; ++ } ++ } ++ ++ ctx->rpi_poe_fan_max_state = num - 1; ++ ++ return 0; ++} ++ ++static int rpi_poe_fan_probe(struct platform_device *pdev) ++{ ++ struct thermal_cooling_device *cdev; ++ struct rpi_poe_fan_ctx *ctx; ++ struct device *hwmon; ++ struct device_node *np = pdev->dev.of_node; ++ struct device_node *fw_node; ++ int ret; ++ ++ fw_node = of_parse_phandle(np, "firmware", 0); ++ if (!fw_node) { ++ dev_err(&pdev->dev, "Missing firmware node\n"); ++ return -ENOENT; ++ } ++ ++ ctx = devm_kzalloc(&pdev->dev, sizeof(*ctx), GFP_KERNEL); ++ if (!ctx) ++ return -ENOMEM; ++ ++ mutex_init(&ctx->lock); ++ ++ ctx->fw = rpi_firmware_get(fw_node); ++ if (!ctx->fw) ++ return -EPROBE_DEFER; ++ ++ platform_set_drvdata(pdev, ctx); ++ ++ ctx->nb.notifier_call = rpi_poe_reboot; ++ ret = register_reboot_notifier(&ctx->nb); ++ if (ret) { ++ dev_err(&pdev->dev, "Failed to register reboot notifier: %i\n", ++ ret); ++ return ret; ++ } ++ ret = read_reg(ctx->fw, POE_DEF_PWM, &ctx->def_pwm_value); ++ if (ret) { ++ dev_err(&pdev->dev, "Failed to get default PWM value: %i\n", ++ ret); ++ goto err; ++ } ++ ret = read_reg(ctx->fw, POE_CUR_PWM, &ctx->pwm_value); ++ if (ret) { ++ dev_err(&pdev->dev, "Failed to get current PWM value: %i\n", ++ ret); ++ goto err; ++ } ++ ++ hwmon = devm_hwmon_device_register_with_groups(&pdev->dev, "rpipoefan", ++ ctx, rpi_poe_fan_groups); ++ if (IS_ERR(hwmon)) { ++ dev_err(&pdev->dev, "Failed to register hwmon device\n"); ++ ret = PTR_ERR(hwmon); ++ goto err; ++ } ++ ++ ret = rpi_poe_fan_of_get_cooling_data(&pdev->dev, ctx); ++ if (ret) ++ return ret; ++ ++ rpi_poe_fan_update_state(ctx, ctx->pwm_value); ++ if (!IS_ENABLED(CONFIG_THERMAL)) ++ return 0; ++ ++ cdev = thermal_of_cooling_device_register(np, ++ "rpi-poe-fan", ctx, ++ &rpi_poe_fan_cooling_ops); ++ if (IS_ERR(cdev)) { ++ dev_err(&pdev->dev, ++ "Failed to register rpi-poe-fan as cooling device"); ++ ret = PTR_ERR(cdev); ++ goto err; ++ } ++ ctx->cdev = cdev; ++ thermal_cdev_update(cdev); ++ ++ return 0; ++err: ++ unregister_reboot_notifier(&ctx->nb); ++ return ret; ++} ++ ++static int rpi_poe_fan_remove(struct platform_device *pdev) ++{ ++ struct rpi_poe_fan_ctx *ctx = platform_get_drvdata(pdev); ++ u32 value = ctx->def_pwm_value; ++ ++ unregister_reboot_notifier(&ctx->nb); ++ thermal_cooling_device_unregister(ctx->cdev); ++ if (ctx->pwm_value != value) { ++ write_reg(ctx->fw, POE_CUR_PWM, &value); ++ } ++ return 0; ++} ++ ++#ifdef CONFIG_PM_SLEEP ++static int rpi_poe_fan_suspend(struct device *dev) ++{ ++ struct rpi_poe_fan_ctx *ctx = dev_get_drvdata(dev); ++ u32 value = 0; ++ int ret = 0; ++ ++ if (ctx->pwm_value != value) ++ ret = write_reg(ctx->fw, POE_CUR_PWM, &value); ++ return ret; ++} ++ ++static int rpi_poe_fan_resume(struct device *dev) ++{ ++ struct rpi_poe_fan_ctx *ctx = dev_get_drvdata(dev); ++ u32 value = ctx->pwm_value; ++ int ret = 0; ++ ++ if (value != 0) ++ ret = write_reg(ctx->fw, POE_CUR_PWM, &value); ++ ++ return ret; ++} ++#endif ++ ++static SIMPLE_DEV_PM_OPS(rpi_poe_fan_pm, rpi_poe_fan_suspend, ++ rpi_poe_fan_resume); ++ ++static const struct of_device_id of_rpi_poe_fan_match[] = { ++ { .compatible = "raspberrypi,rpi-poe-fan", }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, of_rpi_poe_fan_match); ++ ++static struct platform_driver rpi_poe_fan_driver = { ++ .probe = rpi_poe_fan_probe, ++ .remove = rpi_poe_fan_remove, ++ .driver = { ++ .name = "rpi-poe-fan", ++ .pm = &rpi_poe_fan_pm, ++ .of_match_table = of_rpi_poe_fan_match, ++ }, ++}; ++ ++module_platform_driver(rpi_poe_fan_driver); ++ ++MODULE_AUTHOR("Serge Schneider "); ++MODULE_ALIAS("platform:rpi-poe-fan"); ++MODULE_DESCRIPTION("Raspberry Pi PoE HAT fan driver"); ++MODULE_LICENSE("GPL"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0085-cxd2880-CXD2880_SPI_DRV-should-select-DVB_CXD2880-wi.patch b/target/linux/bcm27xx/patches-5.10/950-0085-cxd2880-CXD2880_SPI_DRV-should-select-DVB_CXD2880-wi.patch new file mode 100644 index 0000000000..23bd06f3db --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0085-cxd2880-CXD2880_SPI_DRV-should-select-DVB_CXD2880-wi.patch @@ -0,0 +1,20 @@ +From 5156d25449f1a76a72be090a595ee7e25cb74bc6 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Mon, 17 Sep 2018 17:31:18 +0100 +Subject: [PATCH] cxd2880: CXD2880_SPI_DRV should select DVB_CXD2880 + with MEDIA_SUBDRV_AUTOSELECT + +--- + drivers/media/spi/Kconfig | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/media/spi/Kconfig ++++ b/drivers/media/spi/Kconfig +@@ -25,6 +25,7 @@ menu "Media SPI Adapters" + config CXD2880_SPI_DRV + tristate "Sony CXD2880 SPI support" + depends on DVB_CORE && SPI ++ select DVB_CXD2880 if MEDIA_SUBDRV_AUTOSELECT + default m if !MEDIA_SUBDRV_AUTOSELECT + help + Choose if you would like to have SPI interface support for Sony CXD2880. diff --git a/target/linux/bcm27xx/patches-5.10/950-0086-hwmon-raspberrypi-Prevent-voltage-low-warnings-from-.patch b/target/linux/bcm27xx/patches-5.10/950-0086-hwmon-raspberrypi-Prevent-voltage-low-warnings-from-.patch new file mode 100644 index 0000000000..c6fe514618 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0086-hwmon-raspberrypi-Prevent-voltage-low-warnings-from-.patch @@ -0,0 +1,75 @@ +From f6e40957774cd71b4a8ce2190d94ef8e9b289938 Mon Sep 17 00:00:00 2001 +From: Stefan Wahren +Date: Sat, 6 Oct 2018 16:46:18 +0200 +Subject: [PATCH] hwmon: raspberrypi: Prevent voltage low warnings from + filling log + +Although the correct fix for low voltage warnings is to +improve the power supply, the current implementation +of the detection can fill the log if the warning +happens freqently. This replaces the logging with +slightly custom ratelimited logging. + +Signed-off-by: James Hughes +Signed-off-by: Stefan Wahren +--- + drivers/hwmon/raspberrypi-hwmon.c | 41 ++++++++++++++++++++++++++++--- + 1 file changed, 37 insertions(+), 4 deletions(-) + +--- a/drivers/hwmon/raspberrypi-hwmon.c ++++ b/drivers/hwmon/raspberrypi-hwmon.c +@@ -15,6 +15,36 @@ + #include + #include + ++/* ++ * This section defines some rate limited logging that prevent ++ * repeated messages at much lower Hz than the default kernel settings. ++ * It's usually 5s, this is 5 minutes. ++ * Burst 3 means you may get three messages 'quickly', before ++ * the ratelimiting kicks in. ++ */ ++#define LOCAL_RATELIMIT_INTERVAL (5 * 60 * HZ) ++#define LOCAL_RATELIMIT_BURST 3 ++ ++#ifdef CONFIG_PRINTK ++#define printk_ratelimited_local(fmt, ...) \ ++({ \ ++ static DEFINE_RATELIMIT_STATE(_rs, \ ++ LOCAL_RATELIMIT_INTERVAL, \ ++ LOCAL_RATELIMIT_BURST); \ ++ \ ++ if (__ratelimit(&_rs)) \ ++ printk(fmt, ##__VA_ARGS__); \ ++}) ++#else ++#define printk_ratelimited_local(fmt, ...) \ ++ no_printk(fmt, ##__VA_ARGS__) ++#endif ++ ++#define pr_crit_ratelimited_local(fmt, ...) \ ++ printk_ratelimited_local(KERN_CRIT pr_fmt(fmt), ##__VA_ARGS__) ++#define pr_info_ratelimited_local(fmt, ...) \ ++printk_ratelimited_local(KERN_INFO pr_fmt(fmt), ##__VA_ARGS__) ++ + #define UNDERVOLTAGE_STICKY_BIT BIT(16) + + struct rpi_hwmon_data { +@@ -47,10 +77,13 @@ static void rpi_firmware_get_throttled(s + if (new_uv == old_uv) + return; + +- if (new_uv) +- dev_crit(data->hwmon_dev, "Undervoltage detected!\n"); +- else +- dev_info(data->hwmon_dev, "Voltage normalised\n"); ++ if (new_uv) { ++ pr_crit_ratelimited_local("Under-voltage detected! (0x%08x)\n", ++ value); ++ } else { ++ pr_info_ratelimited_local("Voltage normalised (0x%08x)\n", ++ value); ++ } + + sysfs_notify(&data->hwmon_dev->kobj, NULL, "in0_lcrit_alarm"); + } diff --git a/target/linux/bcm27xx/patches-5.10/950-0087-firmware-raspberrypi-Add-backward-compatible-get_thr.patch b/target/linux/bcm27xx/patches-5.10/950-0087-firmware-raspberrypi-Add-backward-compatible-get_thr.patch new file mode 100644 index 0000000000..ac331f34dc --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0087-firmware-raspberrypi-Add-backward-compatible-get_thr.patch @@ -0,0 +1,79 @@ +From 1910584831fe065c50efc3c07b8ea08ff90e6f31 Mon Sep 17 00:00:00 2001 +From: Stefan Wahren +Date: Sat, 13 Oct 2018 13:31:21 +0200 +Subject: [PATCH] firmware: raspberrypi: Add backward compatible + get_throttled + +Avoid a hard userspace ABI change by adding a compatible get_throttled +sysfs entry. Its value is now feed by the GET_THROTTLED requests of the +new hwmon driver. The first access to get_throttled will generate +a warning. + +Signed-off-by: Stefan Wahren +--- + drivers/firmware/raspberrypi.c | 33 +++++++++++++++++++++++++++++++++ + 1 file changed, 33 insertions(+) + +--- a/drivers/firmware/raspberrypi.c ++++ b/drivers/firmware/raspberrypi.c +@@ -28,6 +28,7 @@ struct rpi_firmware { + struct mbox_chan *chan; /* The property channel. */ + struct completion c; + u32 enabled; ++ u32 get_throttled; + }; + + static struct platform_device *g_pdev; +@@ -174,6 +175,12 @@ int rpi_firmware_property(struct rpi_fir + + kfree(data); + ++ if ((tag == RPI_FIRMWARE_GET_THROTTLED) && ++ memcmp(&fw->get_throttled, tag_data, sizeof(fw->get_throttled))) { ++ memcpy(&fw->get_throttled, tag_data, sizeof(fw->get_throttled)); ++ sysfs_notify(&fw->cl.dev->kobj, NULL, "get_throttled"); ++ } ++ + return ret; + } + EXPORT_SYMBOL_GPL(rpi_firmware_property); +@@ -198,6 +205,27 @@ static int rpi_firmware_notify_reboot(st + return 0; + } + ++static ssize_t get_throttled_show(struct device *dev, ++ struct device_attribute *attr, char *buf) ++{ ++ struct rpi_firmware *fw = dev_get_drvdata(dev); ++ ++ WARN_ONCE(1, "deprecated, use hwmon sysfs instead\n"); ++ ++ return sprintf(buf, "%x\n", fw->get_throttled); ++} ++ ++static DEVICE_ATTR_RO(get_throttled); ++ ++static struct attribute *rpi_firmware_dev_attrs[] = { ++ &dev_attr_get_throttled.attr, ++ NULL, ++}; ++ ++static const struct attribute_group rpi_firmware_dev_group = { ++ .attrs = rpi_firmware_dev_attrs, ++}; ++ + static void + rpi_firmware_print_firmware_revision(struct rpi_firmware *fw) + { +@@ -227,6 +255,11 @@ rpi_register_hwmon_driver(struct device + + rpi_hwmon = platform_device_register_data(dev, "raspberrypi-hwmon", + -1, NULL, 0); ++ ++ if (!IS_ERR_OR_NULL(rpi_hwmon)) { ++ if (devm_device_add_group(dev, &rpi_firmware_dev_group)) ++ dev_err(dev, "Failed to create get_trottled attr\n"); ++ } + } + + static void rpi_register_clk_driver(struct device *dev) diff --git a/target/linux/bcm27xx/patches-5.10/950-0088-sc16is7xx-Don-t-spin-if-no-data-received.patch b/target/linux/bcm27xx/patches-5.10/950-0088-sc16is7xx-Don-t-spin-if-no-data-received.patch new file mode 100644 index 0000000000..b14018d1b1 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0088-sc16is7xx-Don-t-spin-if-no-data-received.patch @@ -0,0 +1,23 @@ +From 0041d17ed3cd7e4ffc6168164c6020e5dcf7aeb4 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 6 Nov 2018 12:57:48 +0000 +Subject: [PATCH] sc16is7xx: Don't spin if no data received + +See: https://github.com/raspberrypi/linux/issues/2676 + +Signed-off-by: Phil Elwell +--- + drivers/tty/serial/sc16is7xx.c | 2 ++ + 1 file changed, 2 insertions(+) + +--- a/drivers/tty/serial/sc16is7xx.c ++++ b/drivers/tty/serial/sc16is7xx.c +@@ -696,6 +696,8 @@ static bool sc16is7xx_port_irq(struct sc + rxlen = sc16is7xx_port_read(port, SC16IS7XX_RXLVL_REG); + if (rxlen) + sc16is7xx_handle_rx(port, rxlen, iir); ++ else ++ return false; + break; + case SC16IS7XX_IIR_THRI_SRC: + sc16is7xx_handle_tx(port); diff --git a/target/linux/bcm27xx/patches-5.10/950-0089-drivers-thermal-step_wise-add-support-for-hysteresis.patch b/target/linux/bcm27xx/patches-5.10/950-0089-drivers-thermal-step_wise-add-support-for-hysteresis.patch new file mode 100644 index 0000000000..2438e089cf --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0089-drivers-thermal-step_wise-add-support-for-hysteresis.patch @@ -0,0 +1,94 @@ +From 61e2e6bc4c30ceca12a917de93ffa9645e4944f7 Mon Sep 17 00:00:00 2001 +From: Ram Chandrasekar +Date: Mon, 7 May 2018 11:54:08 -0600 +Subject: [PATCH] drivers: thermal: step_wise: add support for + hysteresis + +Step wise governor increases the mitigation level when the temperature +goes above a threshold and will decrease the mitigation when the +temperature falls below the threshold. If it were a case, where the +temperature hovers around a threshold, the mitigation will be applied +and removed at every iteration. This reaction to the temperature is +inefficient for performance. + +The use of hysteresis temperature could avoid this ping-pong of +mitigation by relaxing the mitigation to happen only when the +temperature goes below this lower hysteresis value. + +Signed-off-by: Ram Chandrasekar +Signed-off-by: Lina Iyer +--- + drivers/thermal/gov_step_wise.c | 33 +++++++++++++++++++++++---------- + 1 file changed, 23 insertions(+), 10 deletions(-) + +--- a/drivers/thermal/gov_step_wise.c ++++ b/drivers/thermal/gov_step_wise.c +@@ -24,7 +24,7 @@ + * for this trip point + * d. if the trend is THERMAL_TREND_DROP_FULL, use lower limit + * for this trip point +- * If the temperature is lower than a trip point, ++ * If the temperature is lower than a hysteresis temperature, + * a. if the trend is THERMAL_TREND_RAISING, do nothing + * b. if the trend is THERMAL_TREND_DROPPING, use lower cooling + * state for this trip point, if the cooling state already +@@ -115,7 +115,7 @@ static void update_passive_instance(stru + + static void thermal_zone_trip_update(struct thermal_zone_device *tz, int trip) + { +- int trip_temp; ++ int trip_temp, hyst_temp; + enum thermal_trip_type trip_type; + enum thermal_trend trend; + struct thermal_instance *instance; +@@ -123,22 +123,23 @@ static void thermal_zone_trip_update(str + int old_target; + + if (trip == THERMAL_TRIPS_NONE) { +- trip_temp = tz->forced_passive; ++ hyst_temp = trip_temp = tz->forced_passive; + trip_type = THERMAL_TRIPS_NONE; + } else { + tz->ops->get_trip_temp(tz, trip, &trip_temp); ++ hyst_temp = trip_temp; ++ if (tz->ops->get_trip_hyst) { ++ tz->ops->get_trip_hyst(tz, trip, &hyst_temp); ++ hyst_temp = trip_temp - hyst_temp; ++ } + tz->ops->get_trip_type(tz, trip, &trip_type); + } + + trend = get_tz_trend(tz, trip); + +- if (tz->temperature >= trip_temp) { +- throttle = true; +- trace_thermal_zone_trip(tz, trip, trip_type); +- } +- +- dev_dbg(&tz->device, "Trip%d[type=%d,temp=%d]:trend=%d,throttle=%d\n", +- trip, trip_type, trip_temp, trend, throttle); ++ dev_dbg(&tz->device, ++ "Trip%d[type=%d,temp=%d,hyst=%d]:trend=%d,throttle=%d\n", ++ trip, trip_type, trip_temp, hyst_temp, trend, throttle); + + mutex_lock(&tz->lock); + +@@ -147,6 +148,18 @@ static void thermal_zone_trip_update(str + continue; + + old_target = instance->target; ++ throttle = false; ++ /* ++ * Lower the mitigation only if the temperature ++ * goes below the hysteresis temperature. ++ */ ++ if (tz->temperature >= trip_temp || ++ (tz->temperature >= hyst_temp && ++ old_target != THERMAL_NO_TARGET)) { ++ throttle = true; ++ trace_thermal_zone_trip(tz, trip, trip_type); ++ } ++ + instance->target = get_target_state(instance, trend, throttle); + dev_dbg(&instance->cdev->device, "old_target=%d, target=%d\n", + old_target, (int)instance->target); diff --git a/target/linux/bcm27xx/patches-5.10/950-0090-drivers-thermal-step_wise-avoid-throttling-at-hyster.patch b/target/linux/bcm27xx/patches-5.10/950-0090-drivers-thermal-step_wise-avoid-throttling-at-hyster.patch new file mode 100644 index 0000000000..2be7299e8c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0090-drivers-thermal-step_wise-avoid-throttling-at-hyster.patch @@ -0,0 +1,22 @@ +From f220efa380854e2423a47f26acde9355ae016ea3 Mon Sep 17 00:00:00 2001 +From: Serge Schneider +Date: Tue, 2 Oct 2018 11:14:15 +0100 +Subject: [PATCH] drivers: thermal: step_wise: avoid throttling at + hysteresis temperature after dropping below it + +Signed-off-by: Serge Schneider +--- + drivers/thermal/gov_step_wise.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/thermal/gov_step_wise.c ++++ b/drivers/thermal/gov_step_wise.c +@@ -155,7 +155,7 @@ static void thermal_zone_trip_update(str + */ + if (tz->temperature >= trip_temp || + (tz->temperature >= hyst_temp && +- old_target != THERMAL_NO_TARGET)) { ++ old_target == instance->upper)) { + throttle = true; + trace_thermal_zone_trip(tz, trip, trip_type); + } diff --git a/target/linux/bcm27xx/patches-5.10/950-0091-Update-issue-templates-2736.patch b/target/linux/bcm27xx/patches-5.10/950-0091-Update-issue-templates-2736.patch new file mode 100644 index 0000000000..a0f1f0e3eb --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0091-Update-issue-templates-2736.patch @@ -0,0 +1,47 @@ +From 87b9a65d3f7102400bff69dcc692d238fe1d6203 Mon Sep 17 00:00:00 2001 +From: James Hughes +Date: Fri, 2 Nov 2018 11:55:49 +0000 +Subject: [PATCH] Update issue templates (#2736) + +--- + .github/ISSUE_TEMPLATE/bug_report.md | 34 ++++++++++++++++++++++++++++ + 1 file changed, 34 insertions(+) + create mode 100644 .github/ISSUE_TEMPLATE/bug_report.md + +--- /dev/null ++++ b/.github/ISSUE_TEMPLATE/bug_report.md +@@ -0,0 +1,34 @@ ++--- ++name: Bug report ++about: Create a report to help us fix your issue ++ ++--- ++ ++**Is this the right place for my bug report?** ++This repository contains the Linux kernel used on the Raspberry Pi. If you believe that the issue you are seeing is kernel-related, this is the right place. If not, we have other repositories for the GPU firmware at [github.com/raspberrypi/firmware](https://github.com/raspberrypi/firmware) and Raspberry Pi userland applications at [github.com/raspberrypi/userland](https://github.com/raspberrypi/userland). If you have problems with the Raspbian distribution packages, report them in the [github.com/RPi-Distro/repo](https://github.com/RPi-Distro/repo). If you simply have a question, then [the Raspberry Pi forums](https://www.raspberrypi.org/forums) are the best place to ask it. ++ ++**Describe the bug** ++Add a clear and concise description of what you think the bug is. ++ ++**To reproduce** ++List the steps required to reproduce the issue. ++ ++**Expected behaviour** ++Add a clear and concise description of what you expected to happen. ++ ++**Actual behaviour** ++Add a clear and concise description of what actually happened. ++ ++**System** ++ Copy and paste the results of the raspinfo command in to this section. Alternatively, copy and paste a pastebin link, or add answers to the following questions: ++ ++* Which model of Raspberry Pi? e.g. Pi3B+, PiZeroW ++* Which OS and version (`cat /etc/rpi-issue`)? ++* Which firmware version (`vcgencmd version`)? ++* Which kernel version (`uname -a`)? ++ ++**Logs** ++If applicable, add the relevant output from `dmesg` or similar. ++ ++**Additional context** ++Add any other relevant context for the problem. diff --git a/target/linux/bcm27xx/patches-5.10/950-0092-net-lan78xx-Support-auto-downshift-to-100Mb-s.patch b/target/linux/bcm27xx/patches-5.10/950-0092-net-lan78xx-Support-auto-downshift-to-100Mb-s.patch new file mode 100644 index 0000000000..925a81dc28 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0092-net-lan78xx-Support-auto-downshift-to-100Mb-s.patch @@ -0,0 +1,91 @@ +From cbc38ebf8ff6d01cd11270d99762d4216ff4237d Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 26 Nov 2018 19:46:58 +0000 +Subject: [PATCH] net: lan78xx: Support auto-downshift to 100Mb/s + +Ethernet cables with faulty or missing pairs (specifically pairs C and +D) allow auto-negotiation to 1000Mbs, but do not support the successful +establishment of a link. Add a DT property, "microchip,downshift-after", +to configure the number of auto-negotiation failures after which it +falls back to 100Mbs. Valid values are 2, 3, 4, 5 and 0, where 0 means +never downshift. + +Signed-off-by: Phil Elwell +--- + .../bindings/net/microchip,lan78xx.txt | 3 +++ + drivers/net/phy/microchip.c | 27 +++++++++++++++++++ + include/linux/microchipphy.h | 8 ++++++ + 3 files changed, 38 insertions(+) + +--- a/Documentation/devicetree/bindings/net/microchip,lan78xx.txt ++++ b/Documentation/devicetree/bindings/net/microchip,lan78xx.txt +@@ -14,6 +14,9 @@ Optional properties of the embedded PHY: + - microchip,led-modes: a 0..4 element vector, with each element configuring + the operating mode of an LED. Omitted LEDs are turned off. Allowed values + are defined in "include/dt-bindings/net/microchip-lan78xx.h". ++- microchip,downshift-after: sets the number of failed auto-negotiation ++ attempts after which the link is downgraded from 1000BASE-T. Should be one of ++ 2, 3, 4, 5 or 0, where 0 means never downshift. + + Example: + +--- a/drivers/net/phy/microchip.c ++++ b/drivers/net/phy/microchip.c +@@ -217,6 +217,7 @@ static int lan88xx_probe(struct phy_devi + struct device *dev = &phydev->mdio.dev; + struct lan88xx_priv *priv; + u32 led_modes[4]; ++ u32 downshift_after = 0; + int len; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); +@@ -246,6 +247,32 @@ static int lan88xx_probe(struct phy_devi + return -EINVAL; + } + ++ if (!of_property_read_u32(dev->of_node, ++ "microchip,downshift-after", ++ &downshift_after)) { ++ u32 mask = LAN78XX_PHY_CTRL3_DOWNSHIFT_CTRL_MASK; ++ u32 val= LAN78XX_PHY_CTRL3_AUTO_DOWNSHIFT; ++ ++ switch (downshift_after) { ++ case 2: val |= LAN78XX_PHY_CTRL3_DOWNSHIFT_CTRL_2; ++ break; ++ case 3: val |= LAN78XX_PHY_CTRL3_DOWNSHIFT_CTRL_3; ++ break; ++ case 4: val |= LAN78XX_PHY_CTRL3_DOWNSHIFT_CTRL_4; ++ break; ++ case 5: val |= LAN78XX_PHY_CTRL3_DOWNSHIFT_CTRL_5; ++ break; ++ case 0: // Disable completely ++ mask = LAN78XX_PHY_CTRL3_AUTO_DOWNSHIFT; ++ val = 0; ++ break; ++ default: ++ return -EINVAL; ++ } ++ (void)phy_modify_paged(phydev, 1, LAN78XX_PHY_CTRL3, ++ mask, val); ++ } ++ + /* these values can be used to identify internal PHY */ + priv->chip_id = phy_read_mmd(phydev, 3, LAN88XX_MMD3_CHIP_ID); + priv->chip_rev = phy_read_mmd(phydev, 3, LAN88XX_MMD3_CHIP_REV); +--- a/include/linux/microchipphy.h ++++ b/include/linux/microchipphy.h +@@ -61,6 +61,14 @@ + /* Registers specific to the LAN7800/LAN7850 embedded phy */ + #define LAN78XX_PHY_LED_MODE_SELECT (0x1D) + ++#define LAN78XX_PHY_CTRL3 (0x14) ++#define LAN78XX_PHY_CTRL3_AUTO_DOWNSHIFT (0x0010) ++#define LAN78XX_PHY_CTRL3_DOWNSHIFT_CTRL_MASK (0x000c) ++#define LAN78XX_PHY_CTRL3_DOWNSHIFT_CTRL_2 (0x0000) ++#define LAN78XX_PHY_CTRL3_DOWNSHIFT_CTRL_3 (0x0004) ++#define LAN78XX_PHY_CTRL3_DOWNSHIFT_CTRL_4 (0x0008) ++#define LAN78XX_PHY_CTRL3_DOWNSHIFT_CTRL_5 (0x000c) ++ + /* DSP registers */ + #define PHY_ARDENNES_MMD_DEV_3_PHY_CFG (0x806A) + #define PHY_ARDENNES_MMD_DEV_3_PHY_CFG_ZD_DLY_EN_ (0x2000) diff --git a/target/linux/bcm27xx/patches-5.10/950-0093-firmware-raspberrypi-Report-the-fw-variant-during-pr.patch b/target/linux/bcm27xx/patches-5.10/950-0093-firmware-raspberrypi-Report-the-fw-variant-during-pr.patch new file mode 100644 index 0000000000..64df0f7c7f --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0093-firmware-raspberrypi-Report-the-fw-variant-during-pr.patch @@ -0,0 +1,101 @@ +From ab759f3138e5ea798e93003e6ce0ffe66ac2970f Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 10 Jan 2019 17:58:06 +0000 +Subject: [PATCH] firmware: raspberrypi: Report the fw variant during + probe + +The driver already reported the firmware build date during probe. +The mailbox calls have been extended to also report the variant + 1 = standard start.elf + 2 = start_x.elf (includes camera stack) + 3 = start_db.elf (includes assert logging) + 4 = start_cd.elf (cutdown version for smallest memory footprint). +Log the variant during probe. + +Signed-off-by: Dave Stevenson + +firmware: raspberrypi: Report the fw git hash during probe + +The firmware can now report the git hash from which it was built +via the mailbox, so report it during probe. + +Signed-off-by: Dave Stevenson +--- + drivers/firmware/raspberrypi.c | 40 +++++++++++++++++++++- + include/soc/bcm2835/raspberrypi-firmware.h | 2 ++ + 2 files changed, 41 insertions(+), 1 deletion(-) + +--- a/drivers/firmware/raspberrypi.c ++++ b/drivers/firmware/raspberrypi.c +@@ -231,6 +231,15 @@ rpi_firmware_print_firmware_revision(str + { + time64_t date_and_time; + u32 packet; ++ static const char * const variant_strs[] = { ++ "unknown", ++ "start", ++ "start_x", ++ "start_db", ++ "start_cd", ++ }; ++ const char *variant_str = "cmd unsupported"; ++ u32 variant; + int ret = rpi_firmware_property(fw, + RPI_FIRMWARE_GET_FIRMWARE_REVISION, + &packet, sizeof(packet)); +@@ -240,7 +249,35 @@ rpi_firmware_print_firmware_revision(str + + /* This is not compatible with y2038 */ + date_and_time = packet; +- dev_info(fw->cl.dev, "Attached to firmware from %ptT\n", &date_and_time); ++ ++ ret = rpi_firmware_property(fw, RPI_FIRMWARE_GET_FIRMWARE_VARIANT, ++ &variant, sizeof(variant)); ++ ++ if (!ret) { ++ if (variant >= ARRAY_SIZE(variant_strs)) ++ variant = 0; ++ variant_str = variant_strs[variant]; ++ } ++ ++ dev_info(fw->cl.dev, ++ "Attached to firmware from %ptT, variant %s\n", ++ &date_and_time, variant_str); ++} ++ ++static void ++rpi_firmware_print_firmware_hash(struct rpi_firmware *fw) ++{ ++ u32 hash[5]; ++ int ret = rpi_firmware_property(fw, ++ RPI_FIRMWARE_GET_FIRMWARE_HASH, ++ hash, sizeof(hash)); ++ ++ if (ret) ++ return; ++ ++ dev_info(fw->cl.dev, ++ "Firmware hash is %08x%08x%08x%08x%08x\n", ++ hash[0], hash[1], hash[2], hash[3], hash[4]); + } + + static void +@@ -309,6 +346,7 @@ static int rpi_firmware_probe(struct pla + g_pdev = pdev; + + rpi_firmware_print_firmware_revision(fw); ++ rpi_firmware_print_firmware_hash(fw); + rpi_register_hwmon_driver(dev, fw); + rpi_register_clk_driver(dev); + +--- a/include/soc/bcm2835/raspberrypi-firmware.h ++++ b/include/soc/bcm2835/raspberrypi-firmware.h +@@ -38,6 +38,8 @@ struct rpi_firmware_property_tag_header + enum rpi_firmware_property_tag { + RPI_FIRMWARE_PROPERTY_END = 0, + RPI_FIRMWARE_GET_FIRMWARE_REVISION = 0x00000001, ++ RPI_FIRMWARE_GET_FIRMWARE_VARIANT = 0x00000002, ++ RPI_FIRMWARE_GET_FIRMWARE_HASH = 0x00000003, + + RPI_FIRMWARE_SET_CURSOR_INFO = 0x00008010, + RPI_FIRMWARE_SET_CURSOR_STATE = 0x00008011, diff --git a/target/linux/bcm27xx/patches-5.10/950-0094-lan78xx-Debounce-link-events-to-minimize-poll-storm.patch b/target/linux/bcm27xx/patches-5.10/950-0094-lan78xx-Debounce-link-events-to-minimize-poll-storm.patch new file mode 100644 index 0000000000..4924ad59b1 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0094-lan78xx-Debounce-link-events-to-minimize-poll-storm.patch @@ -0,0 +1,45 @@ +From a242ba451fd64f0b9f07605ff0d8f6981aa6e955 Mon Sep 17 00:00:00 2001 +From: Joshua Emele +Date: Wed, 7 Nov 2018 16:07:40 -0800 +Subject: [PATCH] lan78xx: Debounce link events to minimize poll storm + +The bInterval is set to 4 (i.e. 8 microframes => 1ms) and the only bit +that the driver pays attention to is "link was reset". If there's a +flapping status bit in that endpoint data, (such as if PHY negotiation +needs a few tries to get a stable link) then polling at a slower rate +would act as a de-bounce. + +See: https://github.com/raspberrypi/linux/issues/2447 +--- + drivers/net/usb/lan78xx.c | 13 ++++++++++++- + 1 file changed, 12 insertions(+), 1 deletion(-) + +--- a/drivers/net/usb/lan78xx.c ++++ b/drivers/net/usb/lan78xx.c +@@ -434,6 +434,11 @@ static bool enable_tso; + module_param(enable_tso, bool, 0644); + MODULE_PARM_DESC(enable_tso, "Enables TCP segmentation offload"); + ++#define INT_URB_MICROFRAMES_PER_MS 8 ++static int int_urb_interval_ms = 8; ++module_param(int_urb_interval_ms, int, 0); ++MODULE_PARM_DESC(int_urb_interval_ms, "Override usb interrupt urb interval"); ++ + static int lan78xx_read_reg(struct lan78xx_net *dev, u32 index, u32 *data) + { + u32 *buf = kmalloc(sizeof(u32), GFP_KERNEL); +@@ -3760,7 +3765,13 @@ static int lan78xx_probe(struct usb_inte + netdev->max_mtu = MAX_SINGLE_PACKET_SIZE; + netif_set_gso_max_size(netdev, MAX_SINGLE_PACKET_SIZE - MAX_HEADER); + +- period = ep_intr->desc.bInterval; ++ if (int_urb_interval_ms <= 0) ++ period = ep_intr->desc.bInterval; ++ else ++ period = int_urb_interval_ms * INT_URB_MICROFRAMES_PER_MS; ++ ++ netif_notice(dev, probe, netdev, "int urb period %d\n", period); ++ + maxp = usb_maxpacket(dev->udev, dev->pipe_intr, 0); + buf = kmalloc(maxp, GFP_KERNEL); + if (buf) { diff --git a/target/linux/bcm27xx/patches-5.10/950-0095-lan78xx-EEE-support-is-now-a-PHY-property.patch b/target/linux/bcm27xx/patches-5.10/950-0095-lan78xx-EEE-support-is-now-a-PHY-property.patch new file mode 100644 index 0000000000..bd5a604c2b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0095-lan78xx-EEE-support-is-now-a-PHY-property.patch @@ -0,0 +1,26 @@ +From b65b1e498059fd4b6299c5327b2fccd002512dba Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 5 Mar 2019 09:51:22 +0000 +Subject: [PATCH] lan78xx: EEE support is now a PHY property + +Now that EEE support is a property of the PHY, use the PHY's DT node +when querying the EEE-related properties. + +See: https://github.com/raspberrypi/linux/issues/2882 + +Signed-off-by: Phil Elwell +--- + drivers/net/usb/lan78xx.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/net/usb/lan78xx.c ++++ b/drivers/net/usb/lan78xx.c +@@ -2172,7 +2172,7 @@ static int lan78xx_phy_init(struct lan78 + mii_adv_to_linkmode_adv_t(fc, mii_adv); + linkmode_or(phydev->advertising, fc, phydev->advertising); + +- if (of_property_read_bool(dev->udev->dev.of_node, ++ if (of_property_read_bool(phydev->mdio.dev.of_node, + "microchip,eee-enabled")) { + struct ethtool_eee edata; + memset(&edata, 0, sizeof(edata)); diff --git a/target/linux/bcm27xx/patches-5.10/950-0096-bcm2835-dma-Add-support-for-per-channel-flags.patch b/target/linux/bcm27xx/patches-5.10/950-0096-bcm2835-dma-Add-support-for-per-channel-flags.patch new file mode 100644 index 0000000000..160985de0a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0096-bcm2835-dma-Add-support-for-per-channel-flags.patch @@ -0,0 +1,48 @@ +From 1a8d5b7b7503bddd1a78130e2317d16b80fe8cda Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 20 Jul 2018 22:03:41 +0100 +Subject: [PATCH] bcm2835-dma: Add support for per-channel flags + +Add the ability to interpret the high bits of the dreq specifier as +flags to be included in the DMA_CS register. The motivation for this +change is the ability to set the DISDEBUG flag for SD card transfers +to avoid corruption when using the VPU debugger. + +Signed-off-by: Phil Elwell +--- + drivers/dma/bcm2835-dma.c | 10 ++++++++-- + 1 file changed, 8 insertions(+), 2 deletions(-) + +--- a/drivers/dma/bcm2835-dma.c ++++ b/drivers/dma/bcm2835-dma.c +@@ -139,6 +139,10 @@ struct bcm2835_desc { + #define BCM2835_DMA_S_DREQ BIT(10) /* enable SREQ for source */ + #define BCM2835_DMA_S_IGNORE BIT(11) /* ignore source reads - read 0 */ + #define BCM2835_DMA_BURST_LENGTH(x) ((x & 15) << 12) ++#define BCM2835_DMA_CS_FLAGS(x) (x & (BCM2835_DMA_PRIORITY(15) | \ ++ BCM2835_DMA_PANIC_PRIORITY(15) | \ ++ BCM2835_DMA_WAIT_FOR_WRITES | \ ++ BCM2835_DMA_DIS_DEBUG)) + #define BCM2835_DMA_PER_MAP(x) ((x & 31) << 16) /* REQ source */ + #define BCM2835_DMA_WAIT(x) ((x & 31) << 21) /* add DMA-wait cycles */ + #define BCM2835_DMA_NO_WIDE_BURSTS BIT(26) /* no 2 beat write bursts */ +@@ -452,7 +456,8 @@ static void bcm2835_dma_start_desc(struc + c->desc = d = to_bcm2835_dma_desc(&vd->tx); + + writel(d->cb_list[0].paddr, c->chan_base + BCM2835_DMA_ADDR); +- writel(BCM2835_DMA_ACTIVE, c->chan_base + BCM2835_DMA_CS); ++ writel(BCM2835_DMA_ACTIVE | BCM2835_DMA_CS_FLAGS(c->dreq), ++ c->chan_base + BCM2835_DMA_CS); + } + + static irqreturn_t bcm2835_dma_callback(int irq, void *data) +@@ -479,7 +484,8 @@ static irqreturn_t bcm2835_dma_callback( + * if this IRQ handler is threaded.) If the channel is finished, it + * will remain idle despite the ACTIVE flag being set. + */ +- writel(BCM2835_DMA_INT | BCM2835_DMA_ACTIVE, ++ writel(BCM2835_DMA_INT | BCM2835_DMA_ACTIVE | ++ BCM2835_DMA_CS_FLAGS(c->dreq), + c->chan_base + BCM2835_DMA_CS); + + d = c->desc; diff --git a/target/linux/bcm27xx/patches-5.10/950-0097-rtc-rv3028-Add-backup-switchover-mode-support.patch b/target/linux/bcm27xx/patches-5.10/950-0097-rtc-rv3028-Add-backup-switchover-mode-support.patch new file mode 100644 index 0000000000..5e27db1655 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0097-rtc-rv3028-Add-backup-switchover-mode-support.patch @@ -0,0 +1,50 @@ +From 4aefed16e3964d161d32a4f25db849ac16046b13 Mon Sep 17 00:00:00 2001 +From: Phil Howard +Date: Fri, 29 Mar 2019 10:53:14 +0000 +Subject: [PATCH] rtc: rv3028: Add backup switchover mode support + +Signed-off-by: Phil Howard +--- + drivers/rtc/rtc-rv3028.c | 17 +++++++++++++++++ + 1 file changed, 17 insertions(+) + +--- a/drivers/rtc/rtc-rv3028.c ++++ b/drivers/rtc/rtc-rv3028.c +@@ -80,6 +80,7 @@ + + #define RV3028_BACKUP_TCE BIT(5) + #define RV3028_BACKUP_TCR_MASK GENMASK(1,0) ++#define RV3028_BACKUP_BSM_MASK 0x0C + + #define OFFSET_STEP_PPT 953674 + +@@ -789,6 +790,7 @@ static int rv3028_probe(struct i2c_clien + struct rv3028_data *rv3028; + int ret, status; + u32 ohms; ++ u8 bsm; + struct nvmem_config nvmem_cfg = { + .name = "rv3028_nvram", + .word_size = 1, +@@ -860,6 +862,21 @@ static int rv3028_probe(struct i2c_clien + if (ret) + return ret; + ++ /* setup backup switchover mode */ ++ if (!device_property_read_u8(&client->dev, "backup-switchover-mode", ++ &bsm)) { ++ if (bsm <= 3) { ++ ret = regmap_update_bits(rv3028->regmap, RV3028_BACKUP, ++ RV3028_BACKUP_BSM_MASK, ++ (bsm & 0x03) << 2); ++ ++ if (ret) ++ return ret; ++ } else { ++ dev_warn(&client->dev, "invalid backup switchover mode value\n"); ++ } ++ } ++ + /* setup trickle charger */ + if (!device_property_read_u32(&client->dev, "trickle-resistor-ohms", + &ohms)) { diff --git a/target/linux/bcm27xx/patches-5.10/950-0098-lan78xx-use-default-alignment-for-rx-buffers.patch b/target/linux/bcm27xx/patches-5.10/950-0098-lan78xx-use-default-alignment-for-rx-buffers.patch new file mode 100644 index 0000000000..33ea06c51e --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0098-lan78xx-use-default-alignment-for-rx-buffers.patch @@ -0,0 +1,23 @@ +From 4c5342c2a4e2d7fe05d16795e308221b786e862e Mon Sep 17 00:00:00 2001 +From: P33M +Date: Thu, 2 May 2019 11:53:45 +0100 +Subject: [PATCH] lan78xx: use default alignment for rx buffers + +The lan78xx uses a 12-byte hardware rx header, so there is no need +to allocate SKBs with NET_IP_ALIGN set. Removes alignment faults +in both dwc_otg and in ipv6 processing. +--- + drivers/net/usb/lan78xx.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/net/usb/lan78xx.c ++++ b/drivers/net/usb/lan78xx.c +@@ -3161,7 +3161,7 @@ static int rx_submit(struct lan78xx_net + size_t size = dev->rx_urb_size; + int ret = 0; + +- skb = netdev_alloc_skb_ip_align(dev->net, size); ++ skb = netdev_alloc_skb(dev->net, size); + if (!skb) { + usb_free_urb(urb); + return -ENOMEM; diff --git a/target/linux/bcm27xx/patches-5.10/950-0099-media-ov5647-Add-set_fmt-and-get_fmt-calls.patch b/target/linux/bcm27xx/patches-5.10/950-0099-media-ov5647-Add-set_fmt-and-get_fmt-calls.patch new file mode 100644 index 0000000000..df4b83ad0a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0099-media-ov5647-Add-set_fmt-and-get_fmt-calls.patch @@ -0,0 +1,47 @@ +From 3774310df4996e7ce45854ddb47a6cf969295f9d Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 31 Oct 2018 14:55:37 +0000 +Subject: [PATCH] media: ov5647: Add set_fmt and get_fmt calls. + +There's no way to query the subdevice for the supported +resolutions. +Add set_fmt and get_fmt implementations. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov5647.c | 22 ++++++++++++++++++++++ + 1 file changed, 22 insertions(+) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -463,8 +463,30 @@ static int ov5647_enum_mbus_code(struct + return 0; + } + ++static int ov5647_set_get_fmt(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_format *format) ++{ ++ struct v4l2_mbus_framefmt *fmt = &format->format; ++ ++ if (format->pad != 0) ++ return -EINVAL; ++ ++ /* Only one format is supported, so return that */ ++ memset(fmt, 0, sizeof(*fmt)); ++ fmt->code = MEDIA_BUS_FMT_SBGGR8_1X8; ++ fmt->colorspace = V4L2_COLORSPACE_SRGB; ++ fmt->field = V4L2_FIELD_NONE; ++ fmt->width = 640; ++ fmt->height = 480; ++ ++ return 0; ++} ++ + static const struct v4l2_subdev_pad_ops ov5647_subdev_pad_ops = { + .enum_mbus_code = ov5647_enum_mbus_code, ++ .set_fmt = ov5647_set_get_fmt, ++ .get_fmt = ov5647_set_get_fmt, + }; + + static const struct v4l2_subdev_ops ov5647_subdev_ops = { diff --git a/target/linux/bcm27xx/patches-5.10/950-0100-media-ov5647-Add-support-for-PWDN-GPIO.patch b/target/linux/bcm27xx/patches-5.10/950-0100-media-ov5647-Add-support-for-PWDN-GPIO.patch new file mode 100644 index 0000000000..13bcb78aac --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0100-media-ov5647-Add-support-for-PWDN-GPIO.patch @@ -0,0 +1,92 @@ +From 4b8d9d9c7f6d8f863669ce97ac299ca542ad6ecc Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 31 Oct 2018 14:56:33 +0000 +Subject: [PATCH] media: ov5647: Add support for PWDN GPIO. + +Add support for an optional GPIO connected to PWDN on the sensor. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov5647.c | 28 ++++++++++++++++++++++++++++ + 1 file changed, 28 insertions(+) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -21,6 +21,7 @@ + + #include + #include ++#include + #include + #include + #include +@@ -35,6 +36,13 @@ + + #define SENSOR_NAME "ov5647" + ++/* ++ * From the datasheet, "20ms after PWDN goes low or 20ms after RESETB goes ++ * high if reset is inserted after PWDN goes high, host can access sensor's ++ * SCCB to initialize sensor." ++ */ ++#define PWDN_ACTIVE_DELAY_MS 20 ++ + #define MIPI_CTRL00_CLOCK_LANE_GATE BIT(5) + #define MIPI_CTRL00_BUS_IDLE BIT(2) + #define MIPI_CTRL00_CLOCK_LANE_DISABLE BIT(0) +@@ -86,6 +94,7 @@ struct ov5647 { + unsigned int height; + int power_count; + struct clk *xclk; ++ struct gpio_desc *pwdn; + }; + + static inline struct ov5647 *to_state(struct v4l2_subdev *sd) +@@ -355,6 +364,11 @@ static int ov5647_sensor_power(struct v4 + if (on && !ov5647->power_count) { + dev_dbg(&client->dev, "OV5647 power on\n"); + ++ if (ov5647->pwdn) { ++ gpiod_set_value(ov5647->pwdn, 0); ++ msleep(PWDN_ACTIVE_DELAY_MS); ++ } ++ + ret = clk_prepare_enable(ov5647->xclk); + if (ret < 0) { + dev_err(&client->dev, "clk prepare enable failed\n"); +@@ -392,6 +406,8 @@ static int ov5647_sensor_power(struct v4 + dev_dbg(&client->dev, "soft stby failed\n"); + + clk_disable_unprepare(ov5647->xclk); ++ ++ gpiod_set_value(ov5647->pwdn, 1); + } + + /* Update the power count. */ +@@ -603,6 +619,10 @@ static int ov5647_probe(struct i2c_clien + return -EINVAL; + } + ++ /* Request the power down GPIO asserted */ ++ sensor->pwdn = devm_gpiod_get_optional(&client->dev, "pwdn", ++ GPIOD_OUT_HIGH); ++ + mutex_init(&sensor->lock); + + sd = &sensor->sd; +@@ -616,7 +636,15 @@ static int ov5647_probe(struct i2c_clien + if (ret < 0) + goto mutex_remove; + ++ if (sensor->pwdn) { ++ gpiod_set_value(sensor->pwdn, 0); ++ msleep(PWDN_ACTIVE_DELAY_MS); ++ } ++ + ret = ov5647_detect(sd); ++ ++ gpiod_set_value(sensor->pwdn, 1); ++ + if (ret < 0) + goto error; + diff --git a/target/linux/bcm27xx/patches-5.10/950-0101-media-ov5647-Add-support-for-non-continuous-clock-mo.patch b/target/linux/bcm27xx/patches-5.10/950-0101-media-ov5647-Add-support-for-non-continuous-clock-mo.patch new file mode 100644 index 0000000000..364d3c53ea --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0101-media-ov5647-Add-support-for-non-continuous-clock-mo.patch @@ -0,0 +1,79 @@ +From f8ae99474d8555a30615db821c180a7d56b2e73c Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 31 Oct 2018 14:56:47 +0000 +Subject: [PATCH] media: ov5647: Add support for non-continuous clock + mode + +The driver was only supporting continuous clock mode +although this was not stated anywhere. +Non-continuous clock saves a small amount of power and +on some SoCs is easier to interface with. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov5647.c | 17 ++++++++++++++--- + 1 file changed, 14 insertions(+), 3 deletions(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -44,6 +44,7 @@ + #define PWDN_ACTIVE_DELAY_MS 20 + + #define MIPI_CTRL00_CLOCK_LANE_GATE BIT(5) ++#define MIPI_CTRL00_LINE_SYNC_ENABLE BIT(4) + #define MIPI_CTRL00_BUS_IDLE BIT(2) + #define MIPI_CTRL00_CLOCK_LANE_DISABLE BIT(0) + +@@ -95,6 +96,7 @@ struct ov5647 { + int power_count; + struct clk *xclk; + struct gpio_desc *pwdn; ++ unsigned int flags; + }; + + static inline struct ov5647 *to_state(struct v4l2_subdev *sd) +@@ -269,9 +271,15 @@ static int ov5647_set_virtual_channel(st + + static int ov5647_stream_on(struct v4l2_subdev *sd) + { ++ struct ov5647 *ov5647 = to_state(sd); ++ u8 val = MIPI_CTRL00_BUS_IDLE; + int ret; + +- ret = ov5647_write(sd, OV5647_REG_MIPI_CTRL00, MIPI_CTRL00_BUS_IDLE); ++ if (ov5647->flags & V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK) ++ val |= MIPI_CTRL00_CLOCK_LANE_GATE | ++ MIPI_CTRL00_LINE_SYNC_ENABLE; ++ ++ ret = ov5647_write(sd, OV5647_REG_MIPI_CTRL00, val); + if (ret < 0) + return ret; + +@@ -568,7 +576,7 @@ static const struct v4l2_subdev_internal + .open = ov5647_open, + }; + +-static int ov5647_parse_dt(struct device_node *np) ++static int ov5647_parse_dt(struct device_node *np, struct ov5647 *sensor) + { + struct v4l2_fwnode_endpoint bus_cfg = { .bus_type = 0 }; + struct device_node *ep; +@@ -581,6 +589,9 @@ static int ov5647_parse_dt(struct device + + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &bus_cfg); + ++ if (!ret) ++ sensor->flags = bus_cfg.bus.mipi_csi2.flags; ++ + of_node_put(ep); + return ret; + } +@@ -599,7 +610,7 @@ static int ov5647_probe(struct i2c_clien + return -ENOMEM; + + if (IS_ENABLED(CONFIG_OF) && np) { +- ret = ov5647_parse_dt(np); ++ ret = ov5647_parse_dt(np, sensor); + if (ret) { + dev_err(dev, "DT parsing error: %d\n", ret); + return ret; diff --git a/target/linux/bcm27xx/patches-5.10/950-0102-media-tc358743-Increase-FIFO-level-to-374.patch b/target/linux/bcm27xx/patches-5.10/950-0102-media-tc358743-Increase-FIFO-level-to-374.patch new file mode 100644 index 0000000000..b21586d4fc --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0102-media-tc358743-Increase-FIFO-level-to-374.patch @@ -0,0 +1,31 @@ +From 5dc4761b56cbb0f3aa64e23affd2a65b9b7c350a Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 31 Oct 2018 14:56:59 +0000 +Subject: [PATCH] media: tc358743: Increase FIFO level to 374. + +The existing fixed value of 16 worked for UYVY 720P60 over +2 lanes at 594MHz, or UYVY 1080P60 over 4 lanes. (RGB888 +1080P60 needs 6 lanes at 594MHz). +It doesn't allow for lower resolutions to work as the FIFO +underflows. + +374 is required for 1080P24-30 UYVY over 2 lanes @ 972Mbit/s, but +>374 means that the FIFO underflows on 1080P50 UYVY over 2 lanes +@ 972Mbit/s. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/tc358743.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/media/i2c/tc358743.c ++++ b/drivers/media/i2c/tc358743.c +@@ -1950,7 +1950,7 @@ static int tc358743_probe_of(struct tc35 + state->pdata.ddc5v_delay = DDC5V_DELAY_100_MS; + state->pdata.enable_hdcp = false; + /* A FIFO level of 16 should be enough for 2-lane 720p60 at 594 MHz. */ +- state->pdata.fifo_level = 16; ++ state->pdata.fifo_level = 374; + /* + * The PLL input clock is obtained by dividing refclk by pll_prd. + * It must be between 6 MHz and 40 MHz, lower frequency is better. diff --git a/target/linux/bcm27xx/patches-5.10/950-0103-media-tc358743-fix-connected-active-CSI-2-lane-repor.patch b/target/linux/bcm27xx/patches-5.10/950-0103-media-tc358743-fix-connected-active-CSI-2-lane-repor.patch new file mode 100644 index 0000000000..6f876c4248 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0103-media-tc358743-fix-connected-active-CSI-2-lane-repor.patch @@ -0,0 +1,74 @@ +From 5bc5749e4350a09d7b76c84513908f35455b25f1 Mon Sep 17 00:00:00 2001 +From: Philipp Zabel +Date: Thu, 21 Sep 2017 17:30:24 +0200 +Subject: [PATCH] media: tc358743: fix connected/active CSI-2 lane + reporting + +g_mbus_config was supposed to indicate all supported lane numbers, not +only the number of those currently in active use. Since the TC358743 +can dynamically reduce the number of active lanes if the required +bandwidth allows for it, report all lane numbers up to the connected +number of lanes as supported in pdata mode. +In device tree mode, do not report lane count and clock mode at all, as +the receiver driver can determine these from the device tree. + +To allow communicating the number of currently active lanes, add a new +bitfield to the v4l2_mbus_config flags. This is a temporary fix, to be +used only until a better solution is found. + +Signed-off-by: Philipp Zabel +--- + drivers/media/i2c/tc358743.c | 14 ++++++++++++-- + include/media/v4l2-mediabus.h | 8 ++++++++ + 2 files changed, 20 insertions(+), 2 deletions(-) + +--- a/drivers/media/i2c/tc358743.c ++++ b/drivers/media/i2c/tc358743.c +@@ -1609,11 +1609,20 @@ static int tc358743_get_mbus_config(stru + struct v4l2_mbus_config *cfg) + { + struct tc358743_state *state = to_state(sd); ++ const u32 mask = V4L2_MBUS_CSI2_LANE_MASK; ++ ++ if (state->csi_lanes_in_use > state->bus.num_data_lanes) ++ return -EINVAL; + + cfg->type = V4L2_MBUS_CSI2_DPHY; ++ cfg->flags = (state->csi_lanes_in_use << __ffs(mask)) & mask; ++ ++ /* In DT mode, only report the number of active lanes */ ++ if (sd->dev->of_node) ++ return 0; + +- /* Support for non-continuous CSI-2 clock is missing in the driver */ +- cfg->flags = V4L2_MBUS_CSI2_CONTINUOUS_CLOCK; ++ /* Support for non-continuous CSI-2 clock is missing in pdate mode */ ++ cfg->flags |= V4L2_MBUS_CSI2_CONTINUOUS_CLOCK; + + switch (state->csi_lanes_in_use) { + case 1: +@@ -2056,6 +2065,7 @@ static int tc358743_probe(struct i2c_cli + if (pdata) { + state->pdata = *pdata; + state->bus.flags = V4L2_MBUS_CSI2_CONTINUOUS_CLOCK; ++ state->bus.num_data_lanes = 4; + } else { + err = tc358743_probe_of(state); + if (err == -ENODEV) +--- a/include/media/v4l2-mediabus.h ++++ b/include/media/v4l2-mediabus.h +@@ -92,6 +92,14 @@ + V4L2_MBUS_CSI2_CHANNEL_1 | \ + V4L2_MBUS_CSI2_CHANNEL_2 | \ + V4L2_MBUS_CSI2_CHANNEL_3) ++/* ++ * Number of lanes in use, 0 == use all available lanes (default) ++ * ++ * This is a temporary fix for devices that need to reduce the number of active ++ * lanes for certain modes, until g_mbus_config() can be replaced with a better ++ * solution. ++ */ ++#define V4L2_MBUS_CSI2_LANE_MASK (0xf << 10) + + /** + * enum v4l2_mbus_type - media bus type diff --git a/target/linux/bcm27xx/patches-5.10/950-0104-media-tc358743-Add-support-for-972Mbit-s-link-freq.patch b/target/linux/bcm27xx/patches-5.10/950-0104-media-tc358743-Add-support-for-972Mbit-s-link-freq.patch new file mode 100644 index 0000000000..81274adca8 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0104-media-tc358743-Add-support-for-972Mbit-s-link-freq.patch @@ -0,0 +1,79 @@ +From 216cd49e1af96bc615a36cddfad7b5a05e1f7ca2 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 31 Oct 2018 14:57:21 +0000 +Subject: [PATCH] media: tc358743: Add support for 972Mbit/s link freq. + +Adds register setups for running the CSI lanes at 972Mbit/s, +which allows 1080P50 UYVY down 2 lanes. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/tc358743.c | 47 +++++++++++++++++++++++++----------- + 1 file changed, 33 insertions(+), 14 deletions(-) + +--- a/drivers/media/i2c/tc358743.c ++++ b/drivers/media/i2c/tc358743.c +@@ -1979,6 +1979,7 @@ static int tc358743_probe_of(struct tc35 + /* + * The CSI bps per lane must be between 62.5 Mbps and 1 Gbps. + * The default is 594 Mbps for 4-lane 1080p60 or 2-lane 720p60. ++ * 972 Mbps allows 1080P50 UYVY over 2-lane. + */ + bps_pr_lane = 2 * endpoint.link_frequencies[0]; + if (bps_pr_lane < 62500000U || bps_pr_lane > 1000000000U) { +@@ -1992,23 +1993,41 @@ static int tc358743_probe_of(struct tc35 + state->pdata.refclk_hz * state->pdata.pll_prd; + + /* +- * FIXME: These timings are from REF_02 for 594 Mbps per lane (297 MHz +- * link frequency). In principle it should be possible to calculate ++ * FIXME: These timings are from REF_02 for 594 or 972 Mbps per lane ++ * (297 MHz or 486 MHz link frequency). ++ * In principle it should be possible to calculate + * them based on link frequency and resolution. + */ +- if (bps_pr_lane != 594000000U) ++ switch (bps_pr_lane) { ++ default: + dev_warn(dev, "untested bps per lane: %u bps\n", bps_pr_lane); +- state->pdata.lineinitcnt = 0xe80; +- state->pdata.lptxtimecnt = 0x003; +- /* tclk-preparecnt: 3, tclk-zerocnt: 20 */ +- state->pdata.tclk_headercnt = 0x1403; +- state->pdata.tclk_trailcnt = 0x00; +- /* ths-preparecnt: 3, ths-zerocnt: 1 */ +- state->pdata.ths_headercnt = 0x0103; +- state->pdata.twakeup = 0x4882; +- state->pdata.tclk_postcnt = 0x008; +- state->pdata.ths_trailcnt = 0x2; +- state->pdata.hstxvregcnt = 0; ++ case 594000000U: ++ state->pdata.lineinitcnt = 0xe80; ++ state->pdata.lptxtimecnt = 0x003; ++ /* tclk-preparecnt: 3, tclk-zerocnt: 20 */ ++ state->pdata.tclk_headercnt = 0x1403; ++ state->pdata.tclk_trailcnt = 0x00; ++ /* ths-preparecnt: 3, ths-zerocnt: 1 */ ++ state->pdata.ths_headercnt = 0x0103; ++ state->pdata.twakeup = 0x4882; ++ state->pdata.tclk_postcnt = 0x008; ++ state->pdata.ths_trailcnt = 0x2; ++ state->pdata.hstxvregcnt = 0; ++ break; ++ case 972000000U: ++ state->pdata.lineinitcnt = 0x1b58; ++ state->pdata.lptxtimecnt = 0x007; ++ /* tclk-preparecnt: 6, tclk-zerocnt: 40 */ ++ state->pdata.tclk_headercnt = 0x2806; ++ state->pdata.tclk_trailcnt = 0x00; ++ /* ths-preparecnt: 6, ths-zerocnt: 8 */ ++ state->pdata.ths_headercnt = 0x0806; ++ state->pdata.twakeup = 0x4268; ++ state->pdata.tclk_postcnt = 0x008; ++ state->pdata.ths_trailcnt = 0x5; ++ state->pdata.hstxvregcnt = 0; ++ break; ++ } + + state->reset_gpio = devm_gpiod_get_optional(dev, "reset", + GPIOD_OUT_LOW); diff --git a/target/linux/bcm27xx/patches-5.10/950-0105-media-tc358743-Check-I2C-succeeded-during-probe.patch b/target/linux/bcm27xx/patches-5.10/950-0105-media-tc358743-Check-I2C-succeeded-during-probe.patch new file mode 100644 index 0000000000..f26eb80a8f --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0105-media-tc358743-Check-I2C-succeeded-during-probe.patch @@ -0,0 +1,98 @@ +From 58993b47c141a2e0cd57e4b62ae8d07a149a815f Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 31 Oct 2018 14:57:34 +0000 +Subject: [PATCH] media: tc358743: Check I2C succeeded during probe. + +The probe for the TC358743 reads the CHIPID register from +the device and compares it to the expected value of 0. +If the I2C request fails then that also returns 0, so +the driver loads thinking that the device is there. + +Generally I2C communications are reliable so there is +limited need to check the return value on every transfer, +therefore only amend the one read during probe to check +for I2C errors. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/tc358743.c | 27 +++++++++++++++++++++++---- + 1 file changed, 23 insertions(+), 4 deletions(-) + +--- a/drivers/media/i2c/tc358743.c ++++ b/drivers/media/i2c/tc358743.c +@@ -110,7 +110,7 @@ static inline struct tc358743_state *to_ + + /* --------------- I2C --------------- */ + +-static void i2c_rd(struct v4l2_subdev *sd, u16 reg, u8 *values, u32 n) ++static int i2c_rd(struct v4l2_subdev *sd, u16 reg, u8 *values, u32 n) + { + struct tc358743_state *state = to_state(sd); + struct i2c_client *client = state->i2c_client; +@@ -136,6 +136,7 @@ static void i2c_rd(struct v4l2_subdev *s + v4l2_err(sd, "%s: reading register 0x%x from 0x%x failed\n", + __func__, reg, client->addr); + } ++ return err != ARRAY_SIZE(msgs); + } + + static void i2c_wr(struct v4l2_subdev *sd, u16 reg, u8 *values, u32 n) +@@ -192,15 +193,24 @@ static void i2c_wr(struct v4l2_subdev *s + } + } + +-static noinline u32 i2c_rdreg(struct v4l2_subdev *sd, u16 reg, u32 n) ++static noinline u32 i2c_rdreg_err(struct v4l2_subdev *sd, u16 reg, u32 n, ++ int *err) + { ++ int error; + __le32 val = 0; + +- i2c_rd(sd, reg, (u8 __force *)&val, n); ++ error = i2c_rd(sd, reg, (u8 __force *)&val, n); ++ if (err) ++ *err = error; + + return le32_to_cpu(val); + } + ++static inline u32 i2c_rdreg(struct v4l2_subdev *sd, u16 reg, u32 n) ++{ ++ return i2c_rdreg_err(sd, reg, n, NULL); ++} ++ + static noinline void i2c_wrreg(struct v4l2_subdev *sd, u16 reg, u32 val, u32 n) + { + __le32 raw = cpu_to_le32(val); +@@ -229,6 +239,13 @@ static u16 i2c_rd16(struct v4l2_subdev * + return i2c_rdreg(sd, reg, 2); + } + ++static int i2c_rd16_err(struct v4l2_subdev *sd, u16 reg, u16 *value) ++{ ++ int err; ++ *value = i2c_rdreg_err(sd, reg, 2, &err); ++ return err; ++} ++ + static void i2c_wr16(struct v4l2_subdev *sd, u16 reg, u16 val) + { + i2c_wrreg(sd, reg, val, 2); +@@ -2066,6 +2083,7 @@ static int tc358743_probe(struct i2c_cli + struct tc358743_platform_data *pdata = client->dev.platform_data; + struct v4l2_subdev *sd; + u16 irq_mask = MASK_HDMI_MSK | MASK_CSI_MSK; ++ u16 chipid; + int err; + + if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) +@@ -2098,7 +2116,8 @@ static int tc358743_probe(struct i2c_cli + sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | V4L2_SUBDEV_FL_HAS_EVENTS; + + /* i2c access */ +- if ((i2c_rd16(sd, CHIPID) & MASK_CHIPID) != 0) { ++ if (i2c_rd16_err(sd, CHIPID, &chipid) || ++ (chipid & MASK_CHIPID) != 0) { + v4l2_info(sd, "not a TC358743 on address 0x%x\n", + client->addr << 1); + return -ENODEV; diff --git a/target/linux/bcm27xx/patches-5.10/950-0106-media-adv7180-Default-to-the-first-valid-input.patch b/target/linux/bcm27xx/patches-5.10/950-0106-media-adv7180-Default-to-the-first-valid-input.patch new file mode 100644 index 0000000000..bd4b418511 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0106-media-adv7180-Default-to-the-first-valid-input.patch @@ -0,0 +1,45 @@ +From 461de95d791044faba914125a418cd9141a39f02 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 31 Oct 2018 14:57:46 +0000 +Subject: [PATCH] media: adv7180: Default to the first valid input + +The hardware default is differential CVBS on AIN1 & 2, which +isn't very useful. + +Select the first input that is defined as valid for the +chip variant (typically CVBS_AIN1). + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/adv7180.c | 13 +++++++++++++ + 1 file changed, 13 insertions(+) + +--- a/drivers/media/i2c/adv7180.c ++++ b/drivers/media/i2c/adv7180.c +@@ -1259,6 +1259,7 @@ static const struct adv7180_chip_info ad + static int init_device(struct adv7180_state *state) + { + int ret; ++ int i; + + mutex_lock(&state->mutex); + +@@ -1305,6 +1306,18 @@ static int init_device(struct adv7180_st + goto out_unlock; + } + ++ /* Select first valid input */ ++ for (i = 0; i < 32; i++) { ++ if (BIT(i) & state->chip_info->valid_input_mask) { ++ ret = state->chip_info->select_input(state, i); ++ ++ if (ret == 0) { ++ state->input = i; ++ break; ++ } ++ } ++ } ++ + out_unlock: + mutex_unlock(&state->mutex); + diff --git a/target/linux/bcm27xx/patches-5.10/950-0107-media-adv7180-Add-YPrPb-support-for-ADV7282M.patch b/target/linux/bcm27xx/patches-5.10/950-0107-media-adv7180-Add-YPrPb-support-for-ADV7282M.patch new file mode 100644 index 0000000000..ad26dde112 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0107-media-adv7180-Add-YPrPb-support-for-ADV7282M.patch @@ -0,0 +1,24 @@ +From befd41654ff575e9ceb699ed03d1b893bbe88867 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 31 Oct 2018 14:57:56 +0000 +Subject: [PATCH] media: adv7180: Add YPrPb support for ADV7282M + +The ADV7282M can support YPbPr on AIN1-3, but this was +not selectable from the driver. Add it to the list of +supported input modes. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/adv7180.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/media/i2c/adv7180.c ++++ b/drivers/media/i2c/adv7180.c +@@ -1248,6 +1248,7 @@ static const struct adv7180_chip_info ad + BIT(ADV7182_INPUT_SVIDEO_AIN1_AIN2) | + BIT(ADV7182_INPUT_SVIDEO_AIN3_AIN4) | + BIT(ADV7182_INPUT_SVIDEO_AIN7_AIN8) | ++ BIT(ADV7182_INPUT_YPRPB_AIN1_AIN2_AIN3) | + BIT(ADV7182_INPUT_DIFF_CVBS_AIN1_AIN2) | + BIT(ADV7182_INPUT_DIFF_CVBS_AIN3_AIN4) | + BIT(ADV7182_INPUT_DIFF_CVBS_AIN7_AIN8), diff --git a/target/linux/bcm27xx/patches-5.10/950-0108-media-videodev2-Add-helper-defines-for-printing-FOUR.patch b/target/linux/bcm27xx/patches-5.10/950-0108-media-videodev2-Add-helper-defines-for-printing-FOUR.patch new file mode 100644 index 0000000000..8fd25d4afa --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0108-media-videodev2-Add-helper-defines-for-printing-FOUR.patch @@ -0,0 +1,28 @@ +From 460f1e1402d28105f9f3d6e8b8739dcd89bff18e Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 31 Oct 2018 14:58:08 +0000 +Subject: [PATCH] media: videodev2: Add helper defines for printing + FOURCCs + +New helper defines that allow printing of a FOURCC using +printf(V4L2_FOURCC_CONV, V4L2_FOURCC_CONV_ARGS(fourcc)); + +Signed-off-by: Dave Stevenson +--- + include/uapi/linux/videodev2.h | 5 +++++ + 1 file changed, 5 insertions(+) + +--- a/include/uapi/linux/videodev2.h ++++ b/include/uapi/linux/videodev2.h +@@ -82,6 +82,11 @@ + ((__u32)(a) | ((__u32)(b) << 8) | ((__u32)(c) << 16) | ((__u32)(d) << 24)) + #define v4l2_fourcc_be(a, b, c, d) (v4l2_fourcc(a, b, c, d) | (1U << 31)) + ++#define V4L2_FOURCC_CONV "%c%c%c%c%s" ++#define V4L2_FOURCC_CONV_ARGS(fourcc) \ ++ (fourcc) & 0x7f, ((fourcc) >> 8) & 0x7f, ((fourcc) >> 16) & 0x7f, \ ++ ((fourcc) >> 24) & 0x7f, (fourcc) & BIT(31) ? "-BE" : "" ++ + /* + * E N U M S + */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0109-dt-bindings-Document-BCM283x-CSI2-CCP2-receiver.patch b/target/linux/bcm27xx/patches-5.10/950-0109-dt-bindings-Document-BCM283x-CSI2-CCP2-receiver.patch new file mode 100644 index 0000000000..2f5d9a8599 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0109-dt-bindings-Document-BCM283x-CSI2-CCP2-receiver.patch @@ -0,0 +1,103 @@ +From f62b05e593e28e7ed00d25318bd301bb5470de63 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 31 Oct 2018 14:59:06 +0000 +Subject: [PATCH] dt-bindings: Document BCM283x CSI2/CCP2 receiver + +Document the DT bindings for the CSI2/CCP2 receiver peripheral +(known as Unicam) on BCM283x SoCs. + +Signed-off-by: Dave Stevenson +Acked-by: Rob Herring +--- + .../bindings/media/bcm2835-unicam.txt | 85 +++++++++++++++++++ + 1 file changed, 85 insertions(+) + create mode 100644 Documentation/devicetree/bindings/media/bcm2835-unicam.txt + +--- /dev/null ++++ b/Documentation/devicetree/bindings/media/bcm2835-unicam.txt +@@ -0,0 +1,85 @@ ++Broadcom BCM283x Camera Interface (Unicam) ++------------------------------------------ ++ ++The Unicam block on BCM283x SoCs is the receiver for either ++CSI-2 or CCP2 data from image sensors or similar devices. ++ ++The main platform using this SoC is the Raspberry Pi family of boards. ++On the Pi the VideoCore firmware can also control this hardware block, ++and driving it from two different processors will cause issues. ++To avoid this, the firmware checks the device tree configuration ++during boot. If it finds device tree nodes called csi0 or csi1 then ++it will stop the firmware accessing the block, and it can then ++safely be used via the device tree binding. ++ ++Required properties: ++=================== ++- compatible : must be "brcm,bcm2835-unicam". ++- reg : physical base address and length of the register sets for the ++ device. ++- interrupts : should contain the IRQ line for this Unicam instance. ++- clocks : list of clock specifiers, corresponding to entries in ++ clock-names property. ++- clock-names : must contain an "lp" entry, matching entries in the ++ clocks property. ++ ++Unicam supports a single port node. It should contain one 'port' child node ++with child 'endpoint' node. Please refer to the bindings defined in ++Documentation/devicetree/bindings/media/video-interfaces.txt. ++ ++Within the endpoint node the "remote-endpoint" and "data-lanes" properties ++are mandatory. ++Data lane reordering is not supported so the data lanes must be in order, ++starting at 1. The number of data lanes should represent the number of ++usable lanes for the hardware block. That may be limited by either the SoC or ++how the platform presents the interface, and the lower value must be used. ++ ++Lane reordering is not supported on the clock lane either, so the optional ++property "clock-lane" will implicitly be <0>. ++Similarly lane inversion is not supported, therefore "lane-polarities" will ++implicitly be <0 0 0 0 0>. ++Neither of these values will be checked. ++ ++Example: ++ csi1: csi1@7e801000 { ++ compatible = "brcm,bcm2835-unicam"; ++ reg = <0x7e801000 0x800>, ++ <0x7e802004 0x4>; ++ interrupts = <2 7>; ++ clocks = <&clocks BCM2835_CLOCK_CAM1>; ++ clock-names = "lp"; ++ ++ port { ++ csi1_ep: endpoint { ++ remote-endpoint = <&tc358743_0>; ++ data-lanes = <1 2>; ++ }; ++ }; ++ }; ++ ++ i2c0: i2c@7e205000 { ++ tc358743: csi-hdmi-bridge@0f { ++ compatible = "toshiba,tc358743"; ++ reg = <0x0f>; ++ ++ clocks = <&tc358743_clk>; ++ clock-names = "refclk"; ++ ++ tc358743_clk: bridge-clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <27000000>; ++ }; ++ ++ port { ++ tc358743_0: endpoint { ++ remote-endpoint = <&csi1_ep>; ++ clock-lanes = <0>; ++ data-lanes = <1 2>; ++ clock-noncontinuous; ++ link-frequencies = ++ /bits/ 64 <297000000>; ++ }; ++ }; ++ }; ++ }; diff --git a/target/linux/bcm27xx/patches-5.10/950-0110-MAINTAINERS-Add-entry-for-BCM2835-Unicam-driver.patch b/target/linux/bcm27xx/patches-5.10/950-0110-MAINTAINERS-Add-entry-for-BCM2835-Unicam-driver.patch new file mode 100644 index 0000000000..0a0999cc2f --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0110-MAINTAINERS-Add-entry-for-BCM2835-Unicam-driver.patch @@ -0,0 +1,28 @@ +From cf4ad61eafe94c2d049bf159b61e3a1c71837d2b Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 31 Oct 2018 14:59:40 +0000 +Subject: [PATCH] MAINTAINERS: Add entry for BCM2835 Unicam driver + +Adds entry for the new BCM2835 Unicam (CSI-2 receiver) driver + +Signed-off-by: Dave Stevenson +--- + MAINTAINERS | 7 +++++++ + 1 file changed, 7 insertions(+) + +--- a/MAINTAINERS ++++ b/MAINTAINERS +@@ -3417,6 +3417,13 @@ N: bcm113* + N: bcm216* + N: kona + ++BROADCOM BCM2835 CAMERA DRIVER ++M: Dave Stevenson ++L: linux-media@vger.kernel.org ++S: Maintained ++F: drivers/media/platform/bcm2835/ ++F: Documentation/devicetree/bindings/media/bcm2835-unicam.txt ++ + BROADCOM BCM47XX MIPS ARCHITECTURE + M: Hauke Mehrtens + M: Rafał Miłecki diff --git a/target/linux/bcm27xx/patches-5.10/950-0111-media-tc358743-Return-an-appropriate-colorspace-from.patch b/target/linux/bcm27xx/patches-5.10/950-0111-media-tc358743-Return-an-appropriate-colorspace-from.patch new file mode 100644 index 0000000000..c204a51b50 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0111-media-tc358743-Return-an-appropriate-colorspace-from.patch @@ -0,0 +1,98 @@ +From 56feb06d0ad3092abf74957463b7c2023b7f7c95 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 22 Nov 2018 17:31:06 +0000 +Subject: [PATCH] media: tc358743: Return an appropriate colorspace + from tc358743_set_fmt + +When calling tc358743_set_fmt, the code was calling tc358743_get_fmt +to choose a valid format. However that sets the colorspace +based on what was read back from the chip. When you set the format, +then the driver would choose and program the colorspace based +on the format code. + +The result was that if you called try or set format for UYVY +when the current format was RGB3 then you would get told sRGB, +and try RGB3 when current was UYVY and you would get told +SMPTE170M. + +The value programmed into the chip is determined by this driver, +therefore there is no need to read back the value. Return the +colorspace based on the format set/tried instead. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/tc358743.c | 40 +++++++++++++----------------------- + 1 file changed, 14 insertions(+), 26 deletions(-) + +--- a/drivers/media/i2c/tc358743.c ++++ b/drivers/media/i2c/tc358743.c +@@ -1691,12 +1691,23 @@ static int tc358743_enum_mbus_code(struc + return 0; + } + ++static u32 tc358743_g_colorspace(u32 code) ++{ ++ switch (code) { ++ case MEDIA_BUS_FMT_RGB888_1X24: ++ return V4L2_COLORSPACE_SRGB; ++ case MEDIA_BUS_FMT_UYVY8_1X16: ++ return V4L2_COLORSPACE_SMPTE170M; ++ default: ++ return 0; ++ } ++} ++ + static int tc358743_get_fmt(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_format *format) + { + struct tc358743_state *state = to_state(sd); +- u8 vi_rep = i2c_rd8(sd, VI_REP); + + if (format->pad != 0) + return -EINVAL; +@@ -1706,23 +1717,7 @@ static int tc358743_get_fmt(struct v4l2_ + format->format.height = state->timings.bt.height; + format->format.field = V4L2_FIELD_NONE; + +- switch (vi_rep & MASK_VOUT_COLOR_SEL) { +- case MASK_VOUT_COLOR_RGB_FULL: +- case MASK_VOUT_COLOR_RGB_LIMITED: +- format->format.colorspace = V4L2_COLORSPACE_SRGB; +- break; +- case MASK_VOUT_COLOR_601_YCBCR_LIMITED: +- case MASK_VOUT_COLOR_601_YCBCR_FULL: +- format->format.colorspace = V4L2_COLORSPACE_SMPTE170M; +- break; +- case MASK_VOUT_COLOR_709_YCBCR_FULL: +- case MASK_VOUT_COLOR_709_YCBCR_LIMITED: +- format->format.colorspace = V4L2_COLORSPACE_REC709; +- break; +- default: +- format->format.colorspace = 0; +- break; +- } ++ format->format.colorspace = tc358743_g_colorspace(format->format.code); + + return 0; + } +@@ -1737,18 +1732,11 @@ static int tc358743_set_fmt(struct v4l2_ + int ret = tc358743_get_fmt(sd, cfg, format); + + format->format.code = code; ++ format->format.colorspace = tc358743_g_colorspace(code); + + if (ret) + return ret; + +- switch (code) { +- case MEDIA_BUS_FMT_RGB888_1X24: +- case MEDIA_BUS_FMT_UYVY8_1X16: +- break; +- default: +- return -EINVAL; +- } +- + if (format->which == V4L2_SUBDEV_FORMAT_TRY) + return 0; + diff --git a/target/linux/bcm27xx/patches-5.10/950-0112-staging-mmal-vchiq-Avoid-use-of-bool-in-structures.patch b/target/linux/bcm27xx/patches-5.10/950-0112-staging-mmal-vchiq-Avoid-use-of-bool-in-structures.patch new file mode 100644 index 0000000000..4b820ee58b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0112-staging-mmal-vchiq-Avoid-use-of-bool-in-structures.patch @@ -0,0 +1,24 @@ +From ec20cd708f7497a77d8832d5e043214b1a414f94 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Mon, 29 Oct 2018 16:20:46 +0000 +Subject: [PATCH] staging: mmal-vchiq: Avoid use of bool in structures + +Fixes up a checkpatch error "Avoid using bool structure members +because of possible alignment issues". + +Signed-off-by: Dave Stevenson +--- + drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c ++++ b/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c +@@ -1775,7 +1775,7 @@ int vchiq_mmal_component_enable(struct v + + ret = enable_component(instance, component); + if (ret == 0) +- component->enabled = true; ++ component->enabled = 1; + + mutex_unlock(&instance->vchiq_mutex); + diff --git a/target/linux/bcm27xx/patches-5.10/950-0113-staging-mmal-vchiq-Add-support-for-event-callbacks.patch b/target/linux/bcm27xx/patches-5.10/950-0113-staging-mmal-vchiq-Add-support-for-event-callbacks.patch new file mode 100644 index 0000000000..048ba65cbf --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0113-staging-mmal-vchiq-Add-support-for-event-callbacks.patch @@ -0,0 +1,356 @@ +From 9db03c416d385ff601211212e0233a8cf3f42812 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Mon, 24 Sep 2018 18:15:38 +0100 +Subject: [PATCH] staging: mmal-vchiq: Add support for event callbacks. + +(Preparation for the codec driver). +The codec uses the event mechanism to report things such as +resolution changes. It is signalled by the cmd field of the buffer +being non-zero. + +Add support for passing this information out to the client. + +Signed-off-by: Dave Stevenson +--- + .../vc04_services/vchiq-mmal/mmal-common.h | 1 + + .../vc04_services/vchiq-mmal/mmal-msg.h | 35 ++++ + .../vc04_services/vchiq-mmal/mmal-vchiq.c | 170 ++++++++++++++++-- + .../vc04_services/vchiq-mmal/mmal-vchiq.h | 4 + + 4 files changed, 196 insertions(+), 14 deletions(-) + +--- a/drivers/staging/vc04_services/vchiq-mmal/mmal-common.h ++++ b/drivers/staging/vc04_services/vchiq-mmal/mmal-common.h +@@ -50,6 +50,7 @@ struct mmal_buffer { + + struct mmal_msg_context *msg_context; + ++ u32 cmd; /* MMAL command. 0=data. */ + unsigned long length; + u32 mmal_flags; + s64 dts; +--- a/drivers/staging/vc04_services/vchiq-mmal/mmal-msg.h ++++ b/drivers/staging/vc04_services/vchiq-mmal/mmal-msg.h +@@ -346,6 +346,41 @@ struct mmal_msg_port_parameter_get_reply + /* event messages */ + #define MMAL_WORKER_EVENT_SPACE 256 + ++/* Four CC's for events */ ++#define MMAL_FOURCC(a, b, c, d) ((a) | (b << 8) | (c << 16) | (d << 24)) ++ ++#define MMAL_EVENT_ERROR MMAL_FOURCC('E', 'R', 'R', 'O') ++#define MMAL_EVENT_EOS MMAL_FOURCC('E', 'E', 'O', 'S') ++#define MMAL_EVENT_FORMAT_CHANGED MMAL_FOURCC('E', 'F', 'C', 'H') ++#define MMAL_EVENT_PARAMETER_CHANGED MMAL_FOURCC('E', 'P', 'C', 'H') ++ ++/* Structs for each of the event message payloads */ ++struct mmal_msg_event_eos { ++ u32 port_type; /**< Type of port that received the end of stream */ ++ u32 port_index; /**< Index of port that received the end of stream */ ++}; ++ ++/** Format changed event data. */ ++struct mmal_msg_event_format_changed { ++ /* Minimum size of buffers the port requires */ ++ u32 buffer_size_min; ++ /* Minimum number of buffers the port requires */ ++ u32 buffer_num_min; ++ /* Size of buffers the port recommends for optimal performance. ++ * A value of zero means no special recommendation. ++ */ ++ u32 buffer_size_recommended; ++ /* Number of buffers the port recommends for optimal ++ * performance. A value of zero means no special recommendation. ++ */ ++ u32 buffer_num_recommended; ++ ++ u32 es_ptr; ++ struct mmal_es_format format; ++ union mmal_es_specific_format es; ++ u8 extradata[MMAL_FORMAT_EXTRADATA_MAX_SIZE]; ++}; ++ + struct mmal_msg_event_to_host { + u32 client_component; /* component context */ + +--- a/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c ++++ b/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c +@@ -143,6 +143,8 @@ struct mmal_msg_context { + /* Presentation and Decode timestamps */ + s64 pts; + s64 dts; ++ /* MMAL buffer command flag */ ++ u32 cmd; + + int status; /* context status */ + +@@ -233,18 +235,6 @@ release_msg_context(struct mmal_msg_cont + kfree(msg_context); + } + +-/* deals with receipt of event to host message */ +-static void event_to_host_cb(struct vchiq_mmal_instance *instance, +- struct mmal_msg *msg, u32 msg_len) +-{ +- pr_debug("unhandled event\n"); +- pr_debug("component:%u port type:%d num:%d cmd:0x%x length:%d\n", +- msg->u.event_to_host.client_component, +- msg->u.event_to_host.port_type, +- msg->u.event_to_host.port_num, +- msg->u.event_to_host.cmd, msg->u.event_to_host.length); +-} +- + /* workqueue scheduled callback + * + * we do this because it is important we do not call any other vchiq +@@ -266,13 +256,18 @@ static void buffer_work_cb(struct work_s + buffer->mmal_flags = msg_context->u.bulk.mmal_flags; + buffer->dts = msg_context->u.bulk.dts; + buffer->pts = msg_context->u.bulk.pts; ++ buffer->cmd = msg_context->u.bulk.cmd; + +- atomic_dec(&msg_context->u.bulk.port->buffers_with_vpu); ++ if (!buffer->cmd) ++ atomic_dec(&msg_context->u.bulk.port->buffers_with_vpu); + + msg_context->u.bulk.port->buffer_cb(msg_context->u.bulk.instance, + msg_context->u.bulk.port, + msg_context->u.bulk.status, + msg_context->u.bulk.buffer); ++ ++ if (buffer->cmd) ++ mutex_unlock(&msg_context->u.bulk.port->event_context_mutex); + } + + /* workqueue scheduled callback to handle receiving buffers +@@ -350,6 +345,7 @@ static int bulk_receive(struct vchiq_mma + msg_context->u.bulk.buffer_used = rd_len; + msg_context->u.bulk.dts = msg->u.buffer_from_host.buffer_header.dts; + msg_context->u.bulk.pts = msg->u.buffer_from_host.buffer_header.pts; ++ msg_context->u.bulk.cmd = msg->u.buffer_from_host.buffer_header.cmd; + + queue_work(msg_context->instance->bulk_wq, + &msg_context->u.bulk.buffer_to_host_work); +@@ -452,6 +448,103 @@ buffer_from_host(struct vchiq_mmal_insta + return ret; + } + ++/* deals with receipt of event to host message */ ++static void event_to_host_cb(struct vchiq_mmal_instance *instance, ++ struct mmal_msg *msg, u32 msg_len) ++{ ++ /* FIXME: Not going to work on 64 bit */ ++ struct vchiq_mmal_component *component = ++ (struct vchiq_mmal_component *)msg->u.event_to_host.client_component; ++ struct vchiq_mmal_port *port = NULL; ++ struct mmal_msg_context *msg_context; ++ u32 port_num = msg->u.event_to_host.port_num; ++ ++ if (msg->u.buffer_from_host.drvbuf.magic == MMAL_MAGIC) { ++ pr_err("%s: MMAL_MSG_TYPE_BUFFER_TO_HOST with bad magic\n", ++ __func__); ++ return; ++ } ++ ++ switch (msg->u.event_to_host.port_type) { ++ case MMAL_PORT_TYPE_CONTROL: ++ if (port_num) { ++ pr_err("%s: port_num of %u >= number of ports 1", ++ __func__, port_num); ++ return; ++ } ++ port = &component->control; ++ break; ++ case MMAL_PORT_TYPE_INPUT: ++ if (port_num >= component->inputs) { ++ pr_err("%s: port_num of %u >= number of ports %u", ++ __func__, port_num, ++ port_num >= component->inputs); ++ return; ++ } ++ port = &component->input[port_num]; ++ break; ++ case MMAL_PORT_TYPE_OUTPUT: ++ if (port_num >= component->outputs) { ++ pr_err("%s: port_num of %u >= number of ports %u", ++ __func__, port_num, ++ port_num >= component->outputs); ++ return; ++ } ++ port = &component->output[port_num]; ++ break; ++ case MMAL_PORT_TYPE_CLOCK: ++ if (port_num >= component->clocks) { ++ pr_err("%s: port_num of %u >= number of ports %u", ++ __func__, port_num, ++ port_num >= component->clocks); ++ return; ++ } ++ port = &component->clock[port_num]; ++ break; ++ default: ++ break; ++ } ++ ++ if (!mutex_trylock(&port->event_context_mutex)) { ++ pr_err("dropping event 0x%x\n", msg->u.event_to_host.cmd); ++ return; ++ } ++ msg_context = port->event_context; ++ ++ if (msg->h.status != MMAL_MSG_STATUS_SUCCESS) { ++ /* message reception had an error */ ++ //pr_warn ++ pr_err("%s: error %d in reply\n", __func__, msg->h.status); ++ ++ msg_context->u.bulk.status = msg->h.status; ++ } else if (msg->u.event_to_host.length > MMAL_WORKER_EVENT_SPACE) { ++ /* data is not in message, queue a bulk receive */ ++ pr_err("%s: payload not in message - bulk receive??! NOT SUPPORTED\n", ++ __func__); ++ msg_context->u.bulk.status = -1; ++ } else { ++ memcpy(msg_context->u.bulk.buffer->buffer, ++ msg->u.event_to_host.data, ++ msg->u.event_to_host.length); ++ ++ msg_context->u.bulk.buffer_used = ++ msg->u.event_to_host.length; ++ ++ msg_context->u.bulk.mmal_flags = 0; ++ msg_context->u.bulk.dts = MMAL_TIME_UNKNOWN; ++ msg_context->u.bulk.pts = MMAL_TIME_UNKNOWN; ++ msg_context->u.bulk.cmd = msg->u.event_to_host.cmd; ++ ++ pr_debug("event component:%u port type:%d num:%d cmd:0x%x length:%d\n", ++ msg->u.event_to_host.client_component, ++ msg->u.event_to_host.port_type, ++ msg->u.event_to_host.port_num, ++ msg->u.event_to_host.cmd, msg->u.event_to_host.length); ++ } ++ ++ schedule_work(&msg_context->u.bulk.work); ++} ++ + /* deals with receipt of buffer to host message */ + static void buffer_to_host_cb(struct vchiq_mmal_instance *instance, + struct mmal_msg *msg, u32 msg_len) +@@ -1332,6 +1425,7 @@ static int port_disable(struct vchiq_mma + mmalbuf->mmal_flags = 0; + mmalbuf->dts = MMAL_TIME_UNKNOWN; + mmalbuf->pts = MMAL_TIME_UNKNOWN; ++ mmalbuf->cmd = 0; + port->buffer_cb(instance, + port, 0, mmalbuf); + } +@@ -1633,6 +1727,43 @@ int mmal_vchi_buffer_cleanup(struct mmal + } + EXPORT_SYMBOL_GPL(mmal_vchi_buffer_cleanup); + ++static void init_event_context(struct vchiq_mmal_instance *instance, ++ struct vchiq_mmal_port *port) ++{ ++ struct mmal_msg_context *ctx = get_msg_context(instance); ++ ++ mutex_init(&port->event_context_mutex); ++ ++ port->event_context = ctx; ++ ctx->u.bulk.instance = instance; ++ ctx->u.bulk.port = port; ++ ctx->u.bulk.buffer = ++ kzalloc(sizeof(*ctx->u.bulk.buffer), GFP_KERNEL); ++ if (!ctx->u.bulk.buffer) ++ goto release_msg_context; ++ ctx->u.bulk.buffer->buffer = kzalloc(MMAL_WORKER_EVENT_SPACE, ++ GFP_KERNEL); ++ if (!ctx->u.bulk.buffer->buffer) ++ goto release_buffer; ++ ++ INIT_WORK(&ctx->u.bulk.work, buffer_work_cb); ++ return; ++ ++release_buffer: ++ kfree(ctx->u.bulk.buffer); ++release_msg_context: ++ release_msg_context(ctx); ++} ++ ++static void free_event_context(struct vchiq_mmal_port *port) ++{ ++ struct mmal_msg_context *ctx = port->event_context; ++ ++ kfree(ctx->u.bulk.buffer->buffer); ++ kfree(ctx->u.bulk.buffer); ++ release_msg_context(ctx); ++} ++ + /* Initialise a mmal component and its ports + * + */ +@@ -1682,6 +1813,7 @@ int vchiq_mmal_component_init(struct vch + ret = port_info_get(instance, &component->control); + if (ret < 0) + goto release_component; ++ init_event_context(instance, &component->control); + + for (idx = 0; idx < component->inputs; idx++) { + component->input[idx].type = MMAL_PORT_TYPE_INPUT; +@@ -1692,6 +1824,7 @@ int vchiq_mmal_component_init(struct vch + ret = port_info_get(instance, &component->input[idx]); + if (ret < 0) + goto release_component; ++ init_event_context(instance, &component->input[idx]); + } + + for (idx = 0; idx < component->outputs; idx++) { +@@ -1703,6 +1836,7 @@ int vchiq_mmal_component_init(struct vch + ret = port_info_get(instance, &component->output[idx]); + if (ret < 0) + goto release_component; ++ init_event_context(instance, &component->output[idx]); + } + + for (idx = 0; idx < component->clocks; idx++) { +@@ -1714,6 +1848,7 @@ int vchiq_mmal_component_init(struct vch + ret = port_info_get(instance, &component->clock[idx]); + if (ret < 0) + goto release_component; ++ init_event_context(instance, &component->clock[idx]); + } + + *component_out = component; +@@ -1739,7 +1874,7 @@ EXPORT_SYMBOL_GPL(vchiq_mmal_component_i + int vchiq_mmal_component_finalise(struct vchiq_mmal_instance *instance, + struct vchiq_mmal_component *component) + { +- int ret; ++ int ret, idx; + + if (mutex_lock_interruptible(&instance->vchiq_mutex)) + return -EINTR; +@@ -1751,6 +1886,13 @@ int vchiq_mmal_component_finalise(struct + + component->in_use = 0; + ++ for (idx = 0; idx < component->inputs; idx++) ++ free_event_context(&component->input[idx]); ++ for (idx = 0; idx < component->outputs; idx++) ++ free_event_context(&component->output[idx]); ++ for (idx = 0; idx < component->clocks; idx++) ++ free_event_context(&component->clock[idx]); ++ + mutex_unlock(&instance->vchiq_mutex); + + return ret; +--- a/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.h ++++ b/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.h +@@ -79,6 +79,10 @@ struct vchiq_mmal_port { + vchiq_mmal_buffer_cb buffer_cb; + /* callback context */ + void *cb_ctx; ++ ++ /* ensure serialised use of the one event context structure */ ++ struct mutex event_context_mutex; ++ struct mmal_msg_context *event_context; + }; + + struct vchiq_mmal_component { diff --git a/target/linux/bcm27xx/patches-5.10/950-0114-staging-vc04_services-Support-sending-data-to-MMAL-p.patch b/target/linux/bcm27xx/patches-5.10/950-0114-staging-vc04_services-Support-sending-data-to-MMAL-p.patch new file mode 100644 index 0000000000..76a401beeb --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0114-staging-vc04_services-Support-sending-data-to-MMAL-p.patch @@ -0,0 +1,42 @@ +From a15278923fdaa73cdf1bef1ec0f1c973c64dbb43 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Mon, 24 Sep 2018 18:26:02 +0100 +Subject: [PATCH] staging: vc04_services: Support sending data to MMAL + ports + +Add the ability to send data to ports. This only supports +zero copy mode as the required bulk transfer setup calls +are not done. + +Signed-off-by: Dave Stevenson +--- + .../vc04_services/vchiq-mmal/mmal-vchiq.c | 18 +++++++++++++----- + 1 file changed, 13 insertions(+), 5 deletions(-) + +--- a/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c ++++ b/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c +@@ -422,11 +422,19 @@ buffer_from_host(struct vchiq_mmal_insta + m.u.buffer_from_host.buffer_header.data = + (u32)(unsigned long)buf->buffer; + m.u.buffer_from_host.buffer_header.alloc_size = buf->buffer_size; +- m.u.buffer_from_host.buffer_header.length = 0; /* nothing used yet */ +- m.u.buffer_from_host.buffer_header.offset = 0; /* no offset */ +- m.u.buffer_from_host.buffer_header.flags = 0; /* no flags */ +- m.u.buffer_from_host.buffer_header.pts = MMAL_TIME_UNKNOWN; +- m.u.buffer_from_host.buffer_header.dts = MMAL_TIME_UNKNOWN; ++ if (port->type == MMAL_PORT_TYPE_OUTPUT) { ++ m.u.buffer_from_host.buffer_header.length = 0; ++ m.u.buffer_from_host.buffer_header.offset = 0; ++ m.u.buffer_from_host.buffer_header.flags = 0; ++ m.u.buffer_from_host.buffer_header.pts = MMAL_TIME_UNKNOWN; ++ m.u.buffer_from_host.buffer_header.dts = MMAL_TIME_UNKNOWN; ++ } else { ++ m.u.buffer_from_host.buffer_header.length = buf->length; ++ m.u.buffer_from_host.buffer_header.offset = 0; ++ m.u.buffer_from_host.buffer_header.flags = buf->mmal_flags; ++ m.u.buffer_from_host.buffer_header.pts = buf->pts; ++ m.u.buffer_from_host.buffer_header.dts = buf->dts; ++ } + + /* clear buffer type sepecific data */ + memset(&m.u.buffer_from_host.buffer_header_type_specific, 0, diff --git a/target/linux/bcm27xx/patches-5.10/950-0115-media-videobuf2-Allow-exporting-of-a-struct-dmabuf.patch b/target/linux/bcm27xx/patches-5.10/950-0115-media-videobuf2-Allow-exporting-of-a-struct-dmabuf.patch new file mode 100644 index 0000000000..4ef794c6c0 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0115-media-videobuf2-Allow-exporting-of-a-struct-dmabuf.patch @@ -0,0 +1,83 @@ +From 2147f93fd4871833b157834ef708a5b99e8e280b Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Mon, 29 Oct 2018 17:57:45 +0000 +Subject: [PATCH] media: videobuf2: Allow exporting of a struct dmabuf + +videobuf2 only allowed exporting a dmabuf as a file descriptor, +but there are instances where having the struct dma_buf is +useful within the kernel. + +Split the current implementation into two, one step which +exports a struct dma_buf, and the second which converts that +into an fd. + +Signed-off-by: Dave Stevenson +--- + .../media/common/videobuf2/videobuf2-core.c | 21 ++++++++++++++++--- + include/media/videobuf2-core.h | 15 +++++++++++++ + 2 files changed, 33 insertions(+), 3 deletions(-) + +--- a/drivers/media/common/videobuf2/videobuf2-core.c ++++ b/drivers/media/common/videobuf2/videobuf2-core.c +@@ -2140,12 +2140,12 @@ static int __find_plane_by_offset(struct + return -EINVAL; + } + +-int vb2_core_expbuf(struct vb2_queue *q, int *fd, unsigned int type, +- unsigned int index, unsigned int plane, unsigned int flags) ++int vb2_core_expbuf_dmabuf(struct vb2_queue *q, unsigned int type, ++ unsigned int index, unsigned int plane, ++ unsigned int flags, struct dma_buf **dmabuf) + { + struct vb2_buffer *vb = NULL; + struct vb2_plane *vb_plane; +- int ret; + struct dma_buf *dbuf; + + if (q->memory != VB2_MEMORY_MMAP) { +@@ -2195,6 +2195,21 @@ int vb2_core_expbuf(struct vb2_queue *q, + return -EINVAL; + } + ++ *dmabuf = dbuf; ++ return 0; ++} ++EXPORT_SYMBOL_GPL(vb2_core_expbuf_dmabuf); ++ ++int vb2_core_expbuf(struct vb2_queue *q, int *fd, unsigned int type, ++ unsigned int index, unsigned int plane, unsigned int flags) ++{ ++ struct dma_buf *dbuf; ++ int ret; ++ ++ ret = vb2_core_expbuf_dmabuf(q, type, index, plane, flags, &dbuf); ++ if (ret) ++ return ret; ++ + ret = dma_buf_fd(dbuf, flags & ~O_ACCMODE); + if (ret < 0) { + dprintk(q, 3, "buffer %d, plane %d failed to export (%d)\n", +--- a/include/media/videobuf2-core.h ++++ b/include/media/videobuf2-core.h +@@ -902,6 +902,21 @@ int vb2_core_streamon(struct vb2_queue * + int vb2_core_streamoff(struct vb2_queue *q, unsigned int type); + + /** ++ * vb2_core_expbuf_dmabuf() - Export a buffer as a dma_buf structure ++ * @q: videobuf2 queue ++ * @type: buffer type ++ * @index: id number of the buffer ++ * @plane: index of the plane to be exported, 0 for single plane queues ++ * @flags: flags for newly created file, currently only O_CLOEXEC is ++ * supported, refer to manual of open syscall for more details ++ * @dmabuf: Returns the dmabuf pointer ++ * ++ */ ++int vb2_core_expbuf_dmabuf(struct vb2_queue *q, unsigned int type, ++ unsigned int index, unsigned int plane, ++ unsigned int flags, struct dma_buf **dmabuf); ++ ++/** + * vb2_core_expbuf() - Export a buffer as a file descriptor. + * @q: pointer to &struct vb2_queue with videobuf2 queue. + * @fd: pointer to the file descriptor associated with DMABUF diff --git a/target/linux/bcm27xx/patches-5.10/950-0116-staging-mmal-vchiq-Fix-client_component-for-64-bit-k.patch b/target/linux/bcm27xx/patches-5.10/950-0116-staging-mmal-vchiq-Fix-client_component-for-64-bit-k.patch new file mode 100644 index 0000000000..464ec402c5 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0116-staging-mmal-vchiq-Fix-client_component-for-64-bit-k.patch @@ -0,0 +1,35 @@ +From b9154d619c0ae2c8636b9bb3f76fe3daa9dc6d8d Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 22 Jan 2019 12:04:09 +0000 +Subject: [PATCH] staging: mmal-vchiq: Fix client_component for 64 bit + kernel + +The MMAL client_component field is used with the event +mechanism to allow the client to identify the component for +which the event is generated. +The field is only 32bits in size, therefore we can't use a +pointer to the component in a 64 bit kernel. + +Component handles are already held in an array per VCHI +instance, so use the array index as the client_component handle +to avoid having to create a new IDR for this purpose. + +Signed-off-by: Dave Stevenson +--- + drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c | 4 ++-- + 1 file changed, 2 insertions(+), 2 deletions(-) + +--- a/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c ++++ b/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c +@@ -460,9 +460,9 @@ buffer_from_host(struct vchiq_mmal_insta + static void event_to_host_cb(struct vchiq_mmal_instance *instance, + struct mmal_msg *msg, u32 msg_len) + { +- /* FIXME: Not going to work on 64 bit */ ++ int comp_idx = msg->u.event_to_host.client_component; + struct vchiq_mmal_component *component = +- (struct vchiq_mmal_component *)msg->u.event_to_host.client_component; ++ &instance->component[comp_idx]; + struct vchiq_mmal_port *port = NULL; + struct mmal_msg_context *msg_context; + u32 port_num = msg->u.event_to_host.port_num; diff --git a/target/linux/bcm27xx/patches-5.10/950-0117-clk-clk-bcm2835-Use-zd-when-printing-size_t.patch b/target/linux/bcm27xx/patches-5.10/950-0117-clk-clk-bcm2835-Use-zd-when-printing-size_t.patch new file mode 100644 index 0000000000..0a984fb404 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0117-clk-clk-bcm2835-Use-zd-when-printing-size_t.patch @@ -0,0 +1,24 @@ +From 1ade3c32d515dba5afa50f389d374b19d1b76cdb Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 24 Jan 2019 15:09:28 +0000 +Subject: [PATCH] clk: clk-bcm2835: Use %zd when printing size_t + +The debug text for how many clocks have been registered +uses "%d" with a size_t. Correct it to "%zd". + +Signed-off-by: Dave Stevenson +--- + drivers/clk/bcm/clk-bcm2835.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/clk/bcm/clk-bcm2835.c ++++ b/drivers/clk/bcm/clk-bcm2835.c +@@ -2382,7 +2382,7 @@ static int bcm2835_clk_probe(struct plat + return ret; + + /* note that we have registered all the clocks */ +- dev_dbg(dev, "registered %d clocks\n", asize); ++ dev_dbg(dev, "registered %zd clocks\n", asize); + + return 0; + } diff --git a/target/linux/bcm27xx/patches-5.10/950-0118-media-ov5647-Use-gpiod_set_value_cansleep.patch b/target/linux/bcm27xx/patches-5.10/950-0118-media-ov5647-Use-gpiod_set_value_cansleep.patch new file mode 100644 index 0000000000..1c0a24f805 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0118-media-ov5647-Use-gpiod_set_value_cansleep.patch @@ -0,0 +1,54 @@ +From 58f1758adcdbfd1cf556eb3cbb85b88ddcef0840 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 18 Sep 2018 11:08:51 +0100 +Subject: [PATCH] media: ov5647: Use gpiod_set_value_cansleep + +All calls to the gpio library are in contexts that can sleep, +therefore there is no issue with having those GPIOs controlled +by controllers which require sleeping (eg I2C GPIO expanders). + +Switch to using gpiod_set_value_cansleep instead of gpiod_set_value +to avoid triggering the warning in gpiolib should the GPIO +controller need to sleep. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov5647.c | 8 ++++---- + 1 file changed, 4 insertions(+), 4 deletions(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -373,7 +373,7 @@ static int ov5647_sensor_power(struct v4 + dev_dbg(&client->dev, "OV5647 power on\n"); + + if (ov5647->pwdn) { +- gpiod_set_value(ov5647->pwdn, 0); ++ gpiod_set_value_cansleep(ov5647->pwdn, 0); + msleep(PWDN_ACTIVE_DELAY_MS); + } + +@@ -415,7 +415,7 @@ static int ov5647_sensor_power(struct v4 + + clk_disable_unprepare(ov5647->xclk); + +- gpiod_set_value(ov5647->pwdn, 1); ++ gpiod_set_value_cansleep(ov5647->pwdn, 1); + } + + /* Update the power count. */ +@@ -648,13 +648,13 @@ static int ov5647_probe(struct i2c_clien + goto mutex_remove; + + if (sensor->pwdn) { +- gpiod_set_value(sensor->pwdn, 0); ++ gpiod_set_value_cansleep(sensor->pwdn, 0); + msleep(PWDN_ACTIVE_DELAY_MS); + } + + ret = ov5647_detect(sd); + +- gpiod_set_value(sensor->pwdn, 1); ++ gpiod_set_value_cansleep(sensor->pwdn, 1); + + if (ret < 0) + goto error; diff --git a/target/linux/bcm27xx/patches-5.10/950-0119-staging-mmal_vchiq-Add-in-the-Bayer-encoding-formats.patch b/target/linux/bcm27xx/patches-5.10/950-0119-staging-mmal_vchiq-Add-in-the-Bayer-encoding-formats.patch new file mode 100644 index 0000000000..c7a642c4ed --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0119-staging-mmal_vchiq-Add-in-the-Bayer-encoding-formats.patch @@ -0,0 +1,51 @@ +From 39b79b302b63d8ba86a0da4d219e5ad2491bac1d Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 13 Feb 2019 12:33:29 +0000 +Subject: [PATCH] staging: mmal_vchiq: Add in the Bayer encoding + formats + +The list of formats was copied before Bayer support was added. +The ISP supports Bayer and is being supported by the bcm2835_codec +driver, so add in the encodings for them. + +Signed-off-by: Dave Stevenson +--- + .../vc04_services/vchiq-mmal/mmal-encodings.h | 27 +++++++++++++++++++ + 1 file changed, 27 insertions(+) + +--- a/drivers/staging/vc04_services/vchiq-mmal/mmal-encodings.h ++++ b/drivers/staging/vc04_services/vchiq-mmal/mmal-encodings.h +@@ -69,6 +69,33 @@ + */ + #define MMAL_ENCODING_OPAQUE MMAL_FOURCC('O', 'P', 'Q', 'V') + ++/* Bayer formats ++ * FourCC values copied from V4L2 where defined. ++ */ ++/* 8 bit per pixel Bayer formats. */ ++#define MMAL_ENCODING_BAYER_SBGGR8 MMAL_FOURCC('B', 'A', '8', '1') ++#define MMAL_ENCODING_BAYER_SGBRG8 MMAL_FOURCC('G', 'B', 'R', 'G') ++#define MMAL_ENCODING_BAYER_SGRBG8 MMAL_FOURCC('G', 'R', 'B', 'G') ++#define MMAL_ENCODING_BAYER_SRGGB8 MMAL_FOURCC('R', 'G', 'G', 'B') ++ ++/* 10 bit per pixel packed Bayer formats. */ ++#define MMAL_ENCODING_BAYER_SBGGR10P MMAL_FOURCC('p', 'B', 'A', 'A') ++#define MMAL_ENCODING_BAYER_SGRBG10P MMAL_FOURCC('p', 'g', 'A', 'A') ++#define MMAL_ENCODING_BAYER_SGBRG10P MMAL_FOURCC('p', 'G', 'A', 'A') ++#define MMAL_ENCODING_BAYER_SRGGB10P MMAL_FOURCC('p', 'R', 'A', 'A') ++ ++/* 12 bit per pixel packed Bayer formats. */ ++#define MMAL_ENCODING_BAYER_SBGGR12P MMAL_FOURCC('p', 'B', '1', '2') ++#define MMAL_ENCODING_BAYER_SGRBG12P MMAL_FOURCC('p', 'g', '1', '2') ++#define MMAL_ENCODING_BAYER_SGBRG12P MMAL_FOURCC('p', 'G', '1', '2') ++#define MMAL_ENCODING_BAYER_SRGGB12P MMAL_FOURCC('p', 'R', '1', '2') ++ ++/* 16 bit per pixel Bayer formats. */ ++#define MMAL_ENCODING_BAYER_SBGGR16 MMAL_FOURCC('B', 'G', '1', '6') ++#define MMAL_ENCODING_BAYER_SGBRG16 MMAL_FOURCC('G', 'B', '1', '6') ++#define MMAL_ENCODING_BAYER_SGRBG16 MMAL_FOURCC('G', 'R', '1', '6') ++#define MMAL_ENCODING_BAYER_SRGGB16 MMAL_FOURCC('R', 'G', '1', '6') ++ + /** An EGL image handle + */ + #define MMAL_ENCODING_EGL_IMAGE MMAL_FOURCC('E', 'G', 'L', 'I') diff --git a/target/linux/bcm27xx/patches-5.10/950-0120-staging-mmal-vchiq-Update-mmal_parameters.h-with-rec.patch b/target/linux/bcm27xx/patches-5.10/950-0120-staging-mmal-vchiq-Update-mmal_parameters.h-with-rec.patch new file mode 100644 index 0000000000..4ea2b995e8 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0120-staging-mmal-vchiq-Update-mmal_parameters.h-with-rec.patch @@ -0,0 +1,56 @@ +From d3356393f78e85eff4b36ad95d86d5f418a87865 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Mon, 18 Feb 2019 15:52:29 +0000 +Subject: [PATCH] staging: mmal-vchiq: Update mmal_parameters.h with + recently defined params + +mmal_parameters.h hasn't been updated to reflect additions made +over the last few years. Update it to reflect the currently +supported parameters. + +Signed-off-by: Dave Stevenson +--- + .../vchiq-mmal/mmal-parameters.h | 32 ++++++++++++++++++- + 1 file changed, 31 insertions(+), 1 deletion(-) + +--- a/drivers/staging/vc04_services/vchiq-mmal/mmal-parameters.h ++++ b/drivers/staging/vc04_services/vchiq-mmal/mmal-parameters.h +@@ -580,7 +580,37 @@ enum mmal_parameter_video_type { + MMAL_PARAMETER_VIDEO_ENCODE_H264_LOW_DELAY_HRD_FLAG, + + /**< @ref MMAL_PARAMETER_BOOLEAN_T */ +- MMAL_PARAMETER_VIDEO_ENCODE_INLINE_HEADER ++ MMAL_PARAMETER_VIDEO_ENCODE_INLINE_HEADER, ++ ++ /**< Take a @ref MMAL_PARAMETER_BOOLEAN_T. */ ++ MMAL_PARAMETER_VIDEO_ENCODE_SEI_ENABLE, ++ ++ /**< Take a @ref MMAL_PARAMETER_BOOLEAN_T. */ ++ MMAL_PARAMETER_VIDEO_ENCODE_INLINE_VECTORS, ++ ++ /**< Take a @ref MMAL_PARAMETER_VIDEO_RENDER_STATS_T. */ ++ MMAL_PARAMETER_VIDEO_RENDER_STATS, ++ ++ /**< Take a @ref MMAL_PARAMETER_VIDEO_INTERLACE_TYPE_T. */ ++ MMAL_PARAMETER_VIDEO_INTERLACE_TYPE, ++ ++ /**< Takes a @ref MMAL_PARAMETER_BOOLEAN_T */ ++ MMAL_PARAMETER_VIDEO_INTERPOLATE_TIMESTAMPS, ++ ++ /**< Takes a @ref MMAL_PARAMETER_BOOLEAN_T */ ++ MMAL_PARAMETER_VIDEO_ENCODE_SPS_TIMING, ++ ++ /**< Takes a @ref MMAL_PARAMETER_UINT32_T */ ++ MMAL_PARAMETER_VIDEO_MAX_NUM_CALLBACKS, ++ ++ /**< Takes a @ref MMAL_PARAMETER_SOURCE_PATTERN_T */ ++ MMAL_PARAMETER_VIDEO_SOURCE_PATTERN, ++ ++ /**< Takes a @ref MMAL_PARAMETER_BOOLEAN_T */ ++ MMAL_PARAMETER_VIDEO_ENCODE_SEPARATE_NAL_BUFS, ++ ++ /**< Takes a @ref MMAL_PARAMETER_UINT32_T */ ++ MMAL_PARAMETER_VIDEO_DROPPABLE_PFRAME_LENGTH, + }; + + /** Valid mirror modes */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0121-staging-mmal-vchiq-Free-the-event-context-for-contro.patch b/target/linux/bcm27xx/patches-5.10/950-0121-staging-mmal-vchiq-Free-the-event-context-for-contro.patch new file mode 100644 index 0000000000..94743b025b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0121-staging-mmal-vchiq-Free-the-event-context-for-contro.patch @@ -0,0 +1,28 @@ +From fd281e20be4590566f0a75d965318685b8562df6 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 1 May 2019 13:27:23 +0100 +Subject: [PATCH] staging: mmal-vchiq: Free the event context for + control ports + +vchiq_mmal_component_init calls init_event_context for the +control port, but vchiq_mmal_component_finalise didn't free +it, causing a memory leak.. + +Add the free call. + +Signed-off-by: Dave Stevenson +--- + drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c | 2 ++ + 1 file changed, 2 insertions(+) + +--- a/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c ++++ b/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c +@@ -1901,6 +1901,8 @@ int vchiq_mmal_component_finalise(struct + for (idx = 0; idx < component->clocks; idx++) + free_event_context(&component->clock[idx]); + ++ free_event_context(&component->control); ++ + mutex_unlock(&instance->vchiq_mutex); + + return ret; diff --git a/target/linux/bcm27xx/patches-5.10/950-0122-staging-mmal-vchiq-Fix-memory-leak-in-error-path.patch b/target/linux/bcm27xx/patches-5.10/950-0122-staging-mmal-vchiq-Fix-memory-leak-in-error-path.patch new file mode 100644 index 0000000000..e42228e52f --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0122-staging-mmal-vchiq-Fix-memory-leak-in-error-path.patch @@ -0,0 +1,76 @@ +From 00dd46a6ddc94ee87db183dfec1e096c159b1d7b Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 2 May 2019 15:50:01 +0100 +Subject: [PATCH] staging: mmal-vchiq: Fix memory leak in error path + +On error, vchiq_mmal_component_init could leave the +event context allocated for ports. +Clean them up in the error path. + +Signed-off-by: Dave Stevenson +--- + .../vc04_services/vchiq-mmal/mmal-vchiq.c | 29 +++++++++++++------ + 1 file changed, 20 insertions(+), 9 deletions(-) + +--- a/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c ++++ b/drivers/staging/vc04_services/vchiq-mmal/mmal-vchiq.c +@@ -1767,9 +1767,26 @@ static void free_event_context(struct vc + { + struct mmal_msg_context *ctx = port->event_context; + ++ if (!ctx) ++ return; ++ + kfree(ctx->u.bulk.buffer->buffer); + kfree(ctx->u.bulk.buffer); + release_msg_context(ctx); ++ port->event_context = NULL; ++} ++ ++static void release_all_event_contexts(struct vchiq_mmal_component *component) ++{ ++ int idx; ++ ++ for (idx = 0; idx < component->inputs; idx++) ++ free_event_context(&component->input[idx]); ++ for (idx = 0; idx < component->outputs; idx++) ++ free_event_context(&component->output[idx]); ++ for (idx = 0; idx < component->clocks; idx++) ++ free_event_context(&component->clock[idx]); ++ free_event_context(&component->control); + } + + /* Initialise a mmal component and its ports +@@ -1867,6 +1884,7 @@ int vchiq_mmal_component_init(struct vch + + release_component: + destroy_component(instance, component); ++ release_all_event_contexts(component); + unlock: + if (component) + component->in_use = 0; +@@ -1882,7 +1900,7 @@ EXPORT_SYMBOL_GPL(vchiq_mmal_component_i + int vchiq_mmal_component_finalise(struct vchiq_mmal_instance *instance, + struct vchiq_mmal_component *component) + { +- int ret, idx; ++ int ret; + + if (mutex_lock_interruptible(&instance->vchiq_mutex)) + return -EINTR; +@@ -1894,14 +1912,7 @@ int vchiq_mmal_component_finalise(struct + + component->in_use = 0; + +- for (idx = 0; idx < component->inputs; idx++) +- free_event_context(&component->input[idx]); +- for (idx = 0; idx < component->outputs; idx++) +- free_event_context(&component->output[idx]); +- for (idx = 0; idx < component->clocks; idx++) +- free_event_context(&component->clock[idx]); +- +- free_event_context(&component->control); ++ release_all_event_contexts(component); + + mutex_unlock(&instance->vchiq_mutex); + diff --git a/target/linux/bcm27xx/patches-5.10/950-0123-w1-w1-gpio-Make-GPIO-an-output-for-strong-pullup.patch b/target/linux/bcm27xx/patches-5.10/950-0123-w1-w1-gpio-Make-GPIO-an-output-for-strong-pullup.patch new file mode 100644 index 0000000000..286498cc88 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0123-w1-w1-gpio-Make-GPIO-an-output-for-strong-pullup.patch @@ -0,0 +1,27 @@ +From c8ce94db62682da391a3c0d1e148b1a5a959b7e1 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 12 Jun 2019 17:15:05 +0100 +Subject: [PATCH] w1: w1-gpio: Make GPIO an output for strong pullup + +The logic to drive the data line high to implement a strong pullup +assumed that the pin was already an output - setting a value does +not change an input. + +See: https://github.com/raspberrypi/firmware/issues/1143 + +Signed-off-by: Phil Elwell +--- + drivers/w1/masters/w1-gpio.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/w1/masters/w1-gpio.c ++++ b/drivers/w1/masters/w1-gpio.c +@@ -30,7 +30,7 @@ static u8 w1_gpio_set_pullup(void *data, + * This will OVERRIDE open drain emulation and force-pull + * the line high for some time. + */ +- gpiod_set_raw_value(pdata->gpiod, 1); ++ gpiod_direction_output_raw(pdata->gpiod, 1); + msleep(pdata->pullup_duration); + /* + * This will simply set the line as input since we are doing diff --git a/target/linux/bcm27xx/patches-5.10/950-0124-arm-bcm2835-Fix-FIQ-early-ioremap.patch b/target/linux/bcm27xx/patches-5.10/950-0124-arm-bcm2835-Fix-FIQ-early-ioremap.patch new file mode 100644 index 0000000000..5fc558d36b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0124-arm-bcm2835-Fix-FIQ-early-ioremap.patch @@ -0,0 +1,73 @@ +From 8bf21a7f5449fde59e4c9772db0696b3dc4cfaef Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 20 Feb 2019 08:49:39 +0000 +Subject: [PATCH] arm: bcm2835: Fix FIQ early ioremap + +The ioremapping creates mappings within the vmalloc area. The +equivalent early function, create_mapping, now checks that the +requested explicit virtual address is between VMALLOC_START and +VMALLOC_END. As there is no reason to have any correlation between +the physical and virtual addresses, put the required mappings at +VMALLOC_START and above. + +Signed-off-by: Phil Elwell +--- + arch/arm/mach-bcm/board_bcm2835.c | 21 +++++++++++++++------ + 1 file changed, 15 insertions(+), 6 deletions(-) + +--- a/arch/arm/mach-bcm/board_bcm2835.c ++++ b/arch/arm/mach-bcm/board_bcm2835.c +@@ -5,17 +5,20 @@ + + #include + #include ++#include + #include + #include + #include + + #include + #include ++#include ++#include + + #include "platsmp.h" + +-#define BCM2835_USB_VIRT_BASE 0xf0980000 +-#define BCM2835_USB_VIRT_MPHI 0xf0006000 ++#define BCM2835_USB_VIRT_BASE (VMALLOC_START) ++#define BCM2835_USB_VIRT_MPHI (VMALLOC_START + 0x10000) + + static void __init bcm2835_init(void) + { +@@ -74,20 +77,26 @@ static int __init bcm2835_map_usb(unsign + + static void __init bcm2835_map_io(void) + { +- const __be32 *ranges; ++ const __be32 *ranges, *address_cells; ++ unsigned long root, addr_cells; + int soc, len; + unsigned long p2b_offset; + + debug_ll_io_init(); + ++ root = of_get_flat_dt_root(); + /* Find out how to map bus to physical address first from soc/ranges */ +- soc = of_get_flat_dt_subnode_by_name(of_get_flat_dt_root(), "soc"); ++ soc = of_get_flat_dt_subnode_by_name(root, "soc"); + if (soc < 0) + return; ++ address_cells = of_get_flat_dt_prop(root, "#address-cells", &len); ++ if (!address_cells || len < (sizeof(unsigned long))) ++ return; ++ addr_cells = be32_to_cpu(address_cells[0]); + ranges = of_get_flat_dt_prop(soc, "ranges", &len); +- if (!ranges || len < (sizeof(unsigned long) * 3)) ++ if (!ranges || len < (sizeof(unsigned long) * (2 + addr_cells))) + return; +- p2b_offset = be32_to_cpu(ranges[0]) - be32_to_cpu(ranges[1]); ++ p2b_offset = be32_to_cpu(ranges[0]) - be32_to_cpu(ranges[addr_cells]); + + /* Now search for bcm2708-usb node in device tree */ + of_scan_flat_dt(bcm2835_map_usb, &p2b_offset); diff --git a/target/linux/bcm27xx/patches-5.10/950-0125-arm-bcm2835-DMA-can-only-address-1GB.patch b/target/linux/bcm27xx/patches-5.10/950-0125-arm-bcm2835-DMA-can-only-address-1GB.patch new file mode 100644 index 0000000000..6c36ec4e6d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0125-arm-bcm2835-DMA-can-only-address-1GB.patch @@ -0,0 +1,25 @@ +From eac607290fee8b1bcd08c48ac49f089f41a0e696 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 29 May 2019 15:47:42 +0100 +Subject: [PATCH] arm: bcm2835: DMA can only address 1GB + +The legacy peripherals can only address the first gigabyte of RAM, so +ensure that DMA allocations are restricted to that region. + +Signed-off-by: Phil Elwell +--- + arch/arm/mach-bcm/board_bcm2835.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/arch/arm/mach-bcm/board_bcm2835.c ++++ b/arch/arm/mach-bcm/board_bcm2835.c +@@ -114,6 +114,9 @@ static const char * const bcm2835_compat + }; + + DT_MACHINE_START(BCM2835, "BCM2835") ++#if defined(CONFIG_ZONE_DMA) && defined(CONFIG_ARM_LPAE) ++ .dma_zone_size = SZ_1G, ++#endif + .map_io = bcm2835_map_io, + .init_machine = bcm2835_init, + .dt_compat = bcm2835_compat, diff --git a/target/linux/bcm27xx/patches-5.10/950-0126-hwrng-iproc-rng200-Add-BCM2838-support.patch b/target/linux/bcm27xx/patches-5.10/950-0126-hwrng-iproc-rng200-Add-BCM2838-support.patch new file mode 100644 index 0000000000..85585199f9 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0126-hwrng-iproc-rng200-Add-BCM2838-support.patch @@ -0,0 +1,153 @@ +From aae625342e4c3647a1fe7983cac36d658e714602 Mon Sep 17 00:00:00 2001 +From: Stefan Wahren +Date: Sat, 4 May 2019 17:06:15 +0200 +Subject: [PATCH] hwrng: iproc-rng200: Add BCM2838 support + +The HWRNG on the BCM2838 is compatible to iproc-rng200, so add the +support to this driver instead of bcm2835-rng. + +Signed-off-by: Stefan Wahren + +hwrng: iproc-rng200: Correct SoC name + +The Pi 4 SoC is called BCM2711, not BCM2838. + +Fixes: "hwrng: iproc-rng200: Add BCM2838 support" + +Signed-off-by: Phil Elwell +--- + drivers/char/hw_random/Kconfig | 2 +- + drivers/char/hw_random/iproc-rng200.c | 78 +++++++++++++++++++++++++-- + 2 files changed, 76 insertions(+), 4 deletions(-) + +--- a/drivers/char/hw_random/Kconfig ++++ b/drivers/char/hw_random/Kconfig +@@ -104,7 +104,7 @@ config HW_RANDOM_IPROC_RNG200 + default HW_RANDOM + help + This driver provides kernel-side support for the RNG200 +- hardware found on the Broadcom iProc and STB SoCs. ++ hardware found on the Broadcom iProc, BCM2711 and STB SoCs. + + To compile this driver as a module, choose M here: the + module will be called iproc-rng200 +--- a/drivers/char/hw_random/iproc-rng200.c ++++ b/drivers/char/hw_random/iproc-rng200.c +@@ -29,6 +29,7 @@ + #define RNG_CTRL_RNG_RBGEN_MASK 0x00001FFF + #define RNG_CTRL_RNG_RBGEN_ENABLE 0x00000001 + #define RNG_CTRL_RNG_RBGEN_DISABLE 0x00000000 ++#define RNG_CTRL_RNG_DIV_CTRL_SHIFT 13 + + #define RNG_SOFT_RESET_OFFSET 0x04 + #define RNG_SOFT_RESET 0x00000001 +@@ -36,16 +37,23 @@ + #define RBG_SOFT_RESET_OFFSET 0x08 + #define RBG_SOFT_RESET 0x00000001 + ++#define RNG_TOTAL_BIT_COUNT_OFFSET 0x0C ++ ++#define RNG_TOTAL_BIT_COUNT_THRESHOLD_OFFSET 0x10 ++ + #define RNG_INT_STATUS_OFFSET 0x18 + #define RNG_INT_STATUS_MASTER_FAIL_LOCKOUT_IRQ_MASK 0x80000000 + #define RNG_INT_STATUS_STARTUP_TRANSITIONS_MET_IRQ_MASK 0x00020000 + #define RNG_INT_STATUS_NIST_FAIL_IRQ_MASK 0x00000020 + #define RNG_INT_STATUS_TOTAL_BITS_COUNT_IRQ_MASK 0x00000001 + ++#define RNG_INT_ENABLE_OFFSET 0x1C ++ + #define RNG_FIFO_DATA_OFFSET 0x20 + + #define RNG_FIFO_COUNT_OFFSET 0x24 + #define RNG_FIFO_COUNT_RNG_FIFO_COUNT_MASK 0x000000FF ++#define RNG_FIFO_COUNT_RNG_FIFO_THRESHOLD_SHIFT 8 + + struct iproc_rng200_dev { + struct hwrng rng; +@@ -166,6 +174,64 @@ static int iproc_rng200_init(struct hwrn + return 0; + } + ++static int bcm2711_rng200_read(struct hwrng *rng, void *buf, size_t max, ++ bool wait) ++{ ++ struct iproc_rng200_dev *priv = to_rng_priv(rng); ++ u32 max_words = max / sizeof(u32); ++ u32 num_words, count, val; ++ ++ /* ensure warm up period has elapsed */ ++ while (1) { ++ val = ioread32(priv->base + RNG_TOTAL_BIT_COUNT_OFFSET); ++ if (val > 16) ++ break; ++ cpu_relax(); ++ } ++ ++ /* ensure fifo is not empty */ ++ while (1) { ++ num_words = ioread32(priv->base + RNG_FIFO_COUNT_OFFSET) & ++ RNG_FIFO_COUNT_RNG_FIFO_COUNT_MASK; ++ if (num_words) ++ break; ++ if (!wait) ++ return 0; ++ cpu_relax(); ++ } ++ ++ if (num_words > max_words) ++ num_words = max_words; ++ ++ for (count = 0; count < num_words; count++) { ++ ((u32 *)buf)[count] = ioread32(priv->base + ++ RNG_FIFO_DATA_OFFSET); ++ } ++ ++ return num_words * sizeof(u32); ++} ++ ++static int bcm2711_rng200_init(struct hwrng *rng) ++{ ++ struct iproc_rng200_dev *priv = to_rng_priv(rng); ++ uint32_t val; ++ ++ if (ioread32(priv->base + RNG_CTRL_OFFSET) & RNG_CTRL_RNG_RBGEN_MASK) ++ return 0; ++ ++ /* initial numbers generated are "less random" so will be discarded */ ++ val = 0x40000; ++ iowrite32(val, priv->base + RNG_TOTAL_BIT_COUNT_THRESHOLD_OFFSET); ++ /* min fifo count to generate full interrupt */ ++ val = 2 << RNG_FIFO_COUNT_RNG_FIFO_THRESHOLD_SHIFT; ++ iowrite32(val, priv->base + RNG_FIFO_COUNT_OFFSET); ++ /* enable the rng - 1Mhz sample rate */ ++ val = (0x3 << RNG_CTRL_RNG_DIV_CTRL_SHIFT) | RNG_CTRL_RNG_RBGEN_MASK; ++ iowrite32(val, priv->base + RNG_CTRL_OFFSET); ++ ++ return 0; ++} ++ + static void iproc_rng200_cleanup(struct hwrng *rng) + { + struct iproc_rng200_dev *priv = to_rng_priv(rng); +@@ -195,11 +261,17 @@ static int iproc_rng200_probe(struct pla + return PTR_ERR(priv->base); + } + +- priv->rng.name = "iproc-rng200"; +- priv->rng.read = iproc_rng200_read; +- priv->rng.init = iproc_rng200_init; ++ priv->rng.name = pdev->name; + priv->rng.cleanup = iproc_rng200_cleanup; + ++ if (of_device_is_compatible(dev->of_node, "brcm,bcm2711-rng200")) { ++ priv->rng.init = bcm2711_rng200_init; ++ priv->rng.read = bcm2711_rng200_read; ++ } else { ++ priv->rng.init = iproc_rng200_init; ++ priv->rng.read = iproc_rng200_read; ++ } ++ + /* Register driver */ + ret = devm_hwrng_register(dev, &priv->rng); + if (ret) { diff --git a/target/linux/bcm27xx/patches-5.10/950-0127-mmc-sdhci-iproc-Fix-vmmc-regulators-on-iProc.patch b/target/linux/bcm27xx/patches-5.10/950-0127-mmc-sdhci-iproc-Fix-vmmc-regulators-on-iProc.patch new file mode 100644 index 0000000000..770dfc6db7 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0127-mmc-sdhci-iproc-Fix-vmmc-regulators-on-iProc.patch @@ -0,0 +1,46 @@ +From efc6e571660a0d0ca53fb603cc4f132481e8977f Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 2 Aug 2019 15:20:11 +0100 +Subject: [PATCH] mmc: sdhci-iproc: Fix vmmc regulators on iProc + +The Linux support for controlling card power via regulators appears to +be contentious. I would argue that the default behaviour is contrary to +the SDHCI spec - turning off the power writes a reserved value to the +SD Bus Voltage Select field of the Power Control Register, which +seems to kill the Arasan/iProc controller - but fortunately there is a +hook in sdhci_ops to override the behaviour. Borrow the implementation +from sdhci_arasan_set_power. + +Signed-off-by: Phil Elwell +--- + drivers/mmc/host/sdhci-iproc.c | 12 ++++++++++++ + 1 file changed, 12 insertions(+) + +--- a/drivers/mmc/host/sdhci-iproc.c ++++ b/drivers/mmc/host/sdhci-iproc.c +@@ -173,6 +173,17 @@ static unsigned int sdhci_iproc_get_max_ + return pltfm_host->clock; + } + ++static void sdhci_iproc_set_power(struct sdhci_host *host, unsigned char mode, ++ unsigned short vdd) ++{ ++ if (!IS_ERR(host->mmc->supply.vmmc)) { ++ struct mmc_host *mmc = host->mmc; ++ ++ mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd); ++ } ++ sdhci_set_power_noreg(host, mode, vdd); ++} ++ + static const struct sdhci_ops sdhci_iproc_ops = { + .set_clock = sdhci_set_clock, + .get_max_clock = sdhci_iproc_get_max_clock, +@@ -190,6 +201,7 @@ static const struct sdhci_ops sdhci_ipro + .write_b = sdhci_iproc_writeb, + .set_clock = sdhci_set_clock, + .get_max_clock = sdhci_iproc_get_max_clock, ++ .set_power = sdhci_iproc_set_power, + .set_bus_width = sdhci_set_bus_width, + .reset = sdhci_reset, + .set_uhs_signaling = sdhci_set_uhs_signaling, diff --git a/target/linux/bcm27xx/patches-5.10/950-0128-vchiq-Add-36-bit-address-support.patch b/target/linux/bcm27xx/patches-5.10/950-0128-vchiq-Add-36-bit-address-support.patch new file mode 100644 index 0000000000..bfe6fc3869 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0128-vchiq-Add-36-bit-address-support.patch @@ -0,0 +1,202 @@ +From 4237f040ec6d54ef0b3782415d354e5b9a023873 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 1 Nov 2018 17:31:37 +0000 +Subject: [PATCH] vchiq: Add 36-bit address support + +Conditional on a new compatible string, change the pagelist encoding +such that the top 24 bits are the pfn, leaving 8 bits for run length +(-1). + +Signed-off-by: Phil Elwell + +staging/vchiq_arm: Fix bcm2711 compatible string + +Fixes: "vchiq: Add 36-bit address support" + +Signed-off-by: Phil Elwell +--- + .../interface/vchiq_arm/vchiq_2835_arm.c | 90 ++++++++++++++----- + .../interface/vchiq_arm/vchiq_arm.c | 6 ++ + .../interface/vchiq_arm/vchiq_arm.h | 1 + + 3 files changed, 75 insertions(+), 22 deletions(-) + +--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_2835_arm.c ++++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_2835_arm.c +@@ -16,6 +16,8 @@ + #include + + #define TOTAL_SLOTS (VCHIQ_SLOT_ZERO_SLOTS + 2 * 32) ++#define VC_SAFE(x) (g_use_36bit_addrs ? ((u32)(x) | 0xc0000000) : (u32)(x)) ++#define IS_VC_SAFE(x) (g_use_36bit_addrs ? !((x) & ~0x3fffffffull) : 1) + + #include "vchiq_arm.h" + #include "vchiq_connected.h" +@@ -58,6 +60,7 @@ static void __iomem *g_regs; + * of 32. + */ + static unsigned int g_cache_line_size = 32; ++static unsigned int g_use_36bit_addrs = 0; + static unsigned int g_fragments_size; + static char *g_fragments_base; + static char *g_free_fragments; +@@ -100,6 +103,8 @@ int vchiq_platform_init(struct platform_ + g_cache_line_size = drvdata->cache_line_size; + g_fragments_size = 2 * g_cache_line_size; + ++ g_use_36bit_addrs = (dev->dma_pfn_offset == 0); ++ + /* Allocate space for the channels in coherent memory */ + slot_mem_size = PAGE_ALIGN(TOTAL_SLOTS * VCHIQ_SLOT_SIZE); + frag_mem_size = PAGE_ALIGN(g_fragments_size * MAX_FRAGMENTS); +@@ -111,14 +116,21 @@ int vchiq_platform_init(struct platform_ + return -ENOMEM; + } + ++ if (!IS_VC_SAFE(slot_phys)) { ++ dev_err(dev, "allocated DMA memory %pad is not VC-safe\n", ++ &slot_phys); ++ return -ENOMEM; ++ } ++ + WARN_ON(((unsigned long)slot_mem & (PAGE_SIZE - 1)) != 0); ++ channelbase = VC_SAFE(slot_phys); + + vchiq_slot_zero = vchiq_init_slots(slot_mem, slot_mem_size); + if (!vchiq_slot_zero) + return -EINVAL; + + vchiq_slot_zero->platform_data[VCHIQ_PLATFORM_FRAGMENTS_OFFSET_IDX] = +- (int)slot_phys + slot_mem_size; ++ channelbase + slot_mem_size; + vchiq_slot_zero->platform_data[VCHIQ_PLATFORM_FRAGMENTS_COUNT_IDX] = + MAX_FRAGMENTS; + +@@ -151,7 +163,6 @@ int vchiq_platform_init(struct platform_ + } + + /* Send the base address of the slots to VideoCore */ +- channelbase = slot_phys; + err = rpi_firmware_property(fw, RPI_FIRMWARE_VCHIQ_INIT, + &channelbase, sizeof(channelbase)); + if (err || channelbase) { +@@ -229,7 +240,7 @@ vchiq_prepare_bulk_data(struct vchiq_bul + if (!pagelistinfo) + return VCHIQ_ERROR; + +- bulk->data = pagelistinfo->dma_addr; ++ bulk->data = (void *)VC_SAFE(pagelistinfo->dma_addr); + + /* + * Store the pagelistinfo address in remote_data, +@@ -447,25 +458,60 @@ create_pagelist(char *buf, char __user * + + /* Combine adjacent blocks for performance */ + k = 0; +- for_each_sg(scatterlist, sg, dma_buffers, i) { +- u32 len = sg_dma_len(sg); +- u32 addr = sg_dma_address(sg); +- +- /* Note: addrs is the address + page_count - 1 +- * The firmware expects blocks after the first to be page- +- * aligned and a multiple of the page size +- */ +- WARN_ON(len == 0); +- WARN_ON(i && (i != (dma_buffers - 1)) && (len & ~PAGE_MASK)); +- WARN_ON(i && (addr & ~PAGE_MASK)); +- if (k > 0 && +- ((addrs[k - 1] & PAGE_MASK) + +- (((addrs[k - 1] & ~PAGE_MASK) + 1) << PAGE_SHIFT)) +- == (addr & PAGE_MASK)) +- addrs[k - 1] += ((len + PAGE_SIZE - 1) >> PAGE_SHIFT); +- else +- addrs[k++] = (addr & PAGE_MASK) | +- (((len + PAGE_SIZE - 1) >> PAGE_SHIFT) - 1); ++ if (g_use_36bit_addrs) { ++ for_each_sg(scatterlist, sg, dma_buffers, i) { ++ u32 len = sg_dma_len(sg); ++ u64 addr = sg_dma_address(sg); ++ u32 page_id = (u32)((addr >> 4) & ~0xff); ++ u32 sg_pages = (len + PAGE_SIZE - 1) >> PAGE_SHIFT; ++ ++ /* Note: addrs is the address + page_count - 1 ++ * The firmware expects blocks after the first to be page- ++ * aligned and a multiple of the page size ++ */ ++ WARN_ON(len == 0); ++ WARN_ON(i && ++ (i != (dma_buffers - 1)) && (len & ~PAGE_MASK)); ++ WARN_ON(i && (addr & ~PAGE_MASK)); ++ WARN_ON(upper_32_bits(addr) > 0xf); ++ if (k > 0 && ++ ((addrs[k - 1] & ~0xff) + ++ (((addrs[k - 1] & 0xff) + 1) << 8) ++ == page_id)) { ++ u32 inc_pages = min(sg_pages, ++ 0xff - (addrs[k - 1] & 0xff)); ++ addrs[k - 1] += inc_pages; ++ page_id += inc_pages << 8; ++ sg_pages -= inc_pages; ++ } ++ while (sg_pages) { ++ u32 inc_pages = min(sg_pages, 0x100u); ++ addrs[k++] = page_id | (inc_pages - 1); ++ page_id += inc_pages << 8; ++ sg_pages -= inc_pages; ++ } ++ } ++ } else { ++ for_each_sg(scatterlist, sg, dma_buffers, i) { ++ u32 len = sg_dma_len(sg); ++ u32 addr = VC_SAFE(sg_dma_address(sg)); ++ u32 new_pages = (len + PAGE_SIZE - 1) >> PAGE_SHIFT; ++ ++ /* Note: addrs is the address + page_count - 1 ++ * The firmware expects blocks after the first to be page- ++ * aligned and a multiple of the page size ++ */ ++ WARN_ON(len == 0); ++ WARN_ON(i && (i != (dma_buffers - 1)) && (len & ~PAGE_MASK)); ++ WARN_ON(i && (addr & ~PAGE_MASK)); ++ if (k > 0 && ++ ((addrs[k - 1] & PAGE_MASK) + ++ (((addrs[k - 1] & ~PAGE_MASK) + 1) << PAGE_SHIFT)) ++ == (addr & PAGE_MASK)) ++ addrs[k - 1] += new_pages; ++ else ++ addrs[k++] = (addr & PAGE_MASK) | (new_pages - 1); ++ } + } + + /* Partial cache lines (fragments) require special measures */ +--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c ++++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c +@@ -118,6 +118,11 @@ static struct vchiq_drvdata bcm2836_drvd + .cache_line_size = 64, + }; + ++static struct vchiq_drvdata bcm2711_drvdata = { ++ .cache_line_size = 64, ++ .use_36bit_addrs = true, ++}; ++ + static const char *const ioctl_names[] = { + "CONNECT", + "SHUTDOWN", +@@ -2679,6 +2684,7 @@ void vchiq_platform_conn_state_changed(s + static const struct of_device_id vchiq_of_match[] = { + { .compatible = "brcm,bcm2835-vchiq", .data = &bcm2835_drvdata }, + { .compatible = "brcm,bcm2836-vchiq", .data = &bcm2836_drvdata }, ++ { .compatible = "brcm,bcm2711-vchiq", .data = &bcm2711_drvdata }, + {}, + }; + MODULE_DEVICE_TABLE(of, vchiq_of_match); +--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.h ++++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.h +@@ -52,6 +52,7 @@ struct vchiq_arm_state { + + struct vchiq_drvdata { + const unsigned int cache_line_size; ++ const bool use_36bit_addrs; + struct rpi_firmware *fw; + }; + diff --git a/target/linux/bcm27xx/patches-5.10/950-0129-bcm2835-pcm.c-Support-multichannel-audio.patch b/target/linux/bcm27xx/patches-5.10/950-0129-bcm2835-pcm.c-Support-multichannel-audio.patch new file mode 100644 index 0000000000..58be800b80 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0129-bcm2835-pcm.c-Support-multichannel-audio.patch @@ -0,0 +1,46 @@ +From 968742728020752788d4b3a6cd75c977db161b46 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Tue, 30 Apr 2019 19:15:30 +0100 +Subject: [PATCH] bcm2835-pcm.c: Support multichannel audio + +--- + .../vc04_services/bcm2835-audio/bcm2835-pcm.c | 17 +++++++++-------- + 1 file changed, 9 insertions(+), 8 deletions(-) + +--- a/drivers/staging/vc04_services/bcm2835-audio/bcm2835-pcm.c ++++ b/drivers/staging/vc04_services/bcm2835-audio/bcm2835-pcm.c +@@ -14,9 +14,9 @@ static const struct snd_pcm_hardware snd + SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID | + SNDRV_PCM_INFO_SYNC_APPLPTR), + .formats = SNDRV_PCM_FMTBIT_U8 | SNDRV_PCM_FMTBIT_S16_LE, +- .rates = SNDRV_PCM_RATE_CONTINUOUS | SNDRV_PCM_RATE_8000_48000, ++ .rates = SNDRV_PCM_RATE_CONTINUOUS | SNDRV_PCM_RATE_8000_192000, + .rate_min = 8000, +- .rate_max = 48000, ++ .rate_max = 192000, + .channels_min = 1, + .channels_max = 2, + .buffer_bytes_max = 128 * 1024, +@@ -31,15 +31,16 @@ static const struct snd_pcm_hardware snd + SNDRV_PCM_INFO_MMAP | SNDRV_PCM_INFO_MMAP_VALID | + SNDRV_PCM_INFO_SYNC_APPLPTR), + .formats = SNDRV_PCM_FMTBIT_S16_LE, +- .rates = SNDRV_PCM_RATE_CONTINUOUS | SNDRV_PCM_RATE_44100 | +- SNDRV_PCM_RATE_48000, ++ .rates = SNDRV_PCM_RATE_44100 | SNDRV_PCM_RATE_48000 | ++ SNDRV_PCM_RATE_88200 | SNDRV_PCM_RATE_96000 | ++ SNDRV_PCM_RATE_176400 | SNDRV_PCM_RATE_192000, + .rate_min = 44100, +- .rate_max = 48000, ++ .rate_max = 192000, + .channels_min = 2, +- .channels_max = 2, +- .buffer_bytes_max = 128 * 1024, ++ .channels_max = 8, ++ .buffer_bytes_max = 512 * 1024, + .period_bytes_min = 1 * 1024, +- .period_bytes_max = 128 * 1024, ++ .period_bytes_max = 512 * 1024, + .periods_min = 1, + .periods_max = 128, + }; diff --git a/target/linux/bcm27xx/patches-5.10/950-0130-bcmgenet-constrain-max-DMA-burst-length.patch b/target/linux/bcm27xx/patches-5.10/950-0130-bcmgenet-constrain-max-DMA-burst-length.patch new file mode 100644 index 0000000000..1aef72804e --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0130-bcmgenet-constrain-max-DMA-burst-length.patch @@ -0,0 +1,20 @@ +From adfa8e90db935da2b8bdfa9b8e8a3070f6c05818 Mon Sep 17 00:00:00 2001 +From: Jonathan Bell +Date: Wed, 12 Sep 2018 14:44:53 +0100 +Subject: [PATCH] bcmgenet: constrain max DMA burst length + +--- + drivers/net/ethernet/broadcom/genet/bcmgenet.h | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.h ++++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.h +@@ -29,7 +29,7 @@ + #define ENET_PAD 8 + #define ENET_MAX_MTU_SIZE (ETH_DATA_LEN + ETH_HLEN + VLAN_HLEN + \ + ENET_BRCM_TAG_LEN + ETH_FCS_LEN + ENET_PAD) +-#define DMA_MAX_BURST_LENGTH 0x10 ++#define DMA_MAX_BURST_LENGTH 0x08 + + /* misc. configuration */ + #define MAX_NUM_OF_FS_RULES 16 diff --git a/target/linux/bcm27xx/patches-5.10/950-0131-bcmgenet-Better-coalescing-parameter-defaults.patch b/target/linux/bcm27xx/patches-5.10/950-0131-bcmgenet-Better-coalescing-parameter-defaults.patch new file mode 100644 index 0000000000..09164c714d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0131-bcmgenet-Better-coalescing-parameter-defaults.patch @@ -0,0 +1,43 @@ +From c69b192667d50c317bab33e283e7cfce1622e499 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 27 Mar 2019 13:45:46 +0000 +Subject: [PATCH] bcmgenet: Better coalescing parameter defaults + +Set defaults for TX and RX packet coalescing to be equivalent to: + + # ethtool -C eth0 tx-frames 10 + # ethtool -C eth0 rx-usecs 50 + +This may be something we want to set via DT parameters in the +future. + +Signed-off-by: Phil Elwell +--- + drivers/net/ethernet/broadcom/genet/bcmgenet.c | 7 +++++-- + 1 file changed, 5 insertions(+), 2 deletions(-) + +--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c ++++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c +@@ -2595,7 +2595,7 @@ static void bcmgenet_init_tx_ring(struct + + bcmgenet_tdma_ring_writel(priv, index, 0, TDMA_PROD_INDEX); + bcmgenet_tdma_ring_writel(priv, index, 0, TDMA_CONS_INDEX); +- bcmgenet_tdma_ring_writel(priv, index, 1, DMA_MBUF_DONE_THRESH); ++ bcmgenet_tdma_ring_writel(priv, index, 10, DMA_MBUF_DONE_THRESH); + /* Disable rate control for now */ + bcmgenet_tdma_ring_writel(priv, index, flow_period_val, + TDMA_FLOW_PERIOD); +@@ -4058,9 +4058,12 @@ static int bcmgenet_probe(struct platfor + netif_set_real_num_rx_queues(priv->dev, priv->hw_params->rx_queues + 1); + + /* Set default coalescing parameters */ +- for (i = 0; i < priv->hw_params->rx_queues; i++) ++ for (i = 0; i < priv->hw_params->rx_queues; i++) { + priv->rx_rings[i].rx_max_coalesced_frames = 1; ++ priv->rx_rings[i].rx_coalesce_usecs = 50; ++ } + priv->rx_rings[DESC_INDEX].rx_max_coalesced_frames = 1; ++ priv->rx_rings[DESC_INDEX].rx_coalesce_usecs = 50; + + /* libphy will determine the link state */ + netif_carrier_off(dev); diff --git a/target/linux/bcm27xx/patches-5.10/950-0132-net-genet-enable-link-energy-detect-powerdown-for-ex.patch b/target/linux/bcm27xx/patches-5.10/950-0132-net-genet-enable-link-energy-detect-powerdown-for-ex.patch new file mode 100644 index 0000000000..4c6fbe89de --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0132-net-genet-enable-link-energy-detect-powerdown-for-ex.patch @@ -0,0 +1,31 @@ +From 79bf7ef15016f04a100973b6d207d2aa63552898 Mon Sep 17 00:00:00 2001 +From: Jonathan Bell +Date: Tue, 14 May 2019 17:17:59 +0100 +Subject: [PATCH] net: genet: enable link energy detect powerdown for + external PHYs + +There are several warts surrounding bcmgenet_mii_probe() as this +function is called from ndo_open, but it's calling registration-type +functions. The probe should be called at probe time and refactored +such that the PHY device data can be extracted to limit the scope +of this flag to Broadcom PHYs. + +For now, pass this flag in as it puts our attached PHY into a low-power +state when disconnected. + +Signed-off-by: Jonathan Bell +--- + drivers/net/ethernet/broadcom/genet/bcmmii.c | 2 ++ + 1 file changed, 2 insertions(+) + +--- a/drivers/net/ethernet/broadcom/genet/bcmmii.c ++++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c +@@ -293,6 +293,8 @@ int bcmgenet_mii_probe(struct net_device + /* Communicate the integrated PHY revision */ + if (priv->internal_phy) + phy_flags = priv->gphy_rev; ++ else ++ phy_flags = PHY_BRCM_AUTO_PWRDWN_ENABLE; + + /* Initialize link state variables that bcmgenet_mii_setup() uses */ + priv->old_link = -1; diff --git a/target/linux/bcm27xx/patches-5.10/950-0133-spi-bcm2835-enable-shared-interrupt-support.patch b/target/linux/bcm27xx/patches-5.10/950-0133-spi-bcm2835-enable-shared-interrupt-support.patch new file mode 100644 index 0000000000..ce9872f645 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0133-spi-bcm2835-enable-shared-interrupt-support.patch @@ -0,0 +1,35 @@ +From aac689d308b3f6dff8a8ccbd85f8a32078a92318 Mon Sep 17 00:00:00 2001 +From: Martin Sperl +Date: Mon, 13 May 2019 11:05:27 +0000 +Subject: [PATCH] spi: bcm2835: enable shared interrupt support + +Add shared interrupt support for this driver. + +Signed-off-by: Martin Sperl +--- + drivers/spi/spi-bcm2835.c | 7 ++++++- + 1 file changed, 6 insertions(+), 1 deletion(-) + +--- a/drivers/spi/spi-bcm2835.c ++++ b/drivers/spi/spi-bcm2835.c +@@ -379,6 +379,10 @@ static irqreturn_t bcm2835_spi_interrupt + if (bs->tx_len && cs & BCM2835_SPI_CS_DONE) + bcm2835_wr_fifo_blind(bs, BCM2835_SPI_FIFO_SIZE); + ++ /* check if we got interrupt enabled */ ++ if (!(bcm2835_rd(bs, BCM2835_SPI_CS) & BCM2835_SPI_CS_INTR)) ++ return IRQ_NONE; ++ + /* Read as many bytes as possible from FIFO */ + bcm2835_rd_fifo(bs); + /* Write as many bytes as possible to FIFO */ +@@ -1329,7 +1333,8 @@ static int bcm2835_spi_probe(struct plat + bcm2835_wr(bs, BCM2835_SPI_CS, + BCM2835_SPI_CS_CLEAR_RX | BCM2835_SPI_CS_CLEAR_TX); + +- err = devm_request_irq(&pdev->dev, bs->irq, bcm2835_spi_interrupt, 0, ++ err = devm_request_irq(&pdev->dev, bs->irq, bcm2835_spi_interrupt, ++ IRQF_SHARED, + dev_name(&pdev->dev), bs); + if (err) { + dev_err(&pdev->dev, "could not request IRQ: %d\n", err); diff --git a/target/linux/bcm27xx/patches-5.10/950-0134-clk-bcm2835-Don-t-wait-for-pllh-lock.patch b/target/linux/bcm27xx/patches-5.10/950-0134-clk-bcm2835-Don-t-wait-for-pllh-lock.patch new file mode 100644 index 0000000000..3a8d43665b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0134-clk-bcm2835-Don-t-wait-for-pllh-lock.patch @@ -0,0 +1,38 @@ +From c1fb629fa486608edab88fb4aa9ab54dd2dcb52c Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 23 Jan 2019 16:11:50 +0000 +Subject: [PATCH] clk-bcm2835: Don't wait for pllh lock + +Signed-off-by: Phil Elwell +--- + drivers/clk/bcm/clk-bcm2835.c | 18 ++++++++++-------- + 1 file changed, 10 insertions(+), 8 deletions(-) + +--- a/drivers/clk/bcm/clk-bcm2835.c ++++ b/drivers/clk/bcm/clk-bcm2835.c +@@ -644,15 +644,17 @@ static int bcm2835_pll_on(struct clk_hw + spin_unlock(&cprman->regs_lock); + + /* Wait for the PLL to lock. */ +- timeout = ktime_add_ns(ktime_get(), LOCK_TIMEOUT_NS); +- while (!(cprman_read(cprman, CM_LOCK) & data->lock_mask)) { +- if (ktime_after(ktime_get(), timeout)) { +- dev_err(cprman->dev, "%s: couldn't lock PLL\n", +- clk_hw_get_name(hw)); +- return -ETIMEDOUT; +- } ++ if (strcmp(data->name, "pllh")) { ++ timeout = ktime_add_ns(ktime_get(), LOCK_TIMEOUT_NS); ++ while (!(cprman_read(cprman, CM_LOCK) & data->lock_mask)) { ++ if (ktime_after(ktime_get(), timeout)) { ++ dev_err(cprman->dev, "%s: couldn't lock PLL\n", ++ clk_hw_get_name(hw)); ++ return -ETIMEDOUT; ++ } + +- cpu_relax(); ++ cpu_relax(); ++ } + } + + cprman_write(cprman, data->a2w_ctrl_reg, diff --git a/target/linux/bcm27xx/patches-5.10/950-0135-soc-bcm-bcm2835-pm-Add-support-for-2711.patch b/target/linux/bcm27xx/patches-5.10/950-0135-soc-bcm-bcm2835-pm-Add-support-for-2711.patch new file mode 100644 index 0000000000..4624dd2c1c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0135-soc-bcm-bcm2835-pm-Add-support-for-2711.patch @@ -0,0 +1,102 @@ +From ca09b9e400f42e5be7d0646237f6ada07ee6c01c Mon Sep 17 00:00:00 2001 +From: Eric Anholt +Date: Fri, 11 Jan 2019 17:31:07 -0800 +Subject: [PATCH] soc: bcm: bcm2835-pm: Add support for 2711. + +Without the actual power management part any more, there's a lot less +to set up for V3D. We just need to clear the RSTN field for the power +domain, and expose the reset controller for toggling it again. + +This is definitely incomplete -- the old ISP and H264 is in the old +bridge, but since we have no consumers of it I've just done the +minimum to get V3D working. + +Signed-off-by: Eric Anholt +--- + drivers/mfd/bcm2835-pm.c | 11 +++++++++++ + drivers/soc/bcm/bcm2835-power.c | 22 ++++++++++++++++++++++ + include/linux/mfd/bcm2835-pm.h | 1 + + 3 files changed, 34 insertions(+) + +--- a/drivers/mfd/bcm2835-pm.c ++++ b/drivers/mfd/bcm2835-pm.c +@@ -50,6 +50,17 @@ static int bcm2835_pm_probe(struct platf + if (ret) + return ret; + ++ /* Map the ARGON ASB regs if present. */ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 2); ++ if (res) { ++ pm->arg_asb = devm_ioremap_resource(dev, res); ++ if (IS_ERR(pm->arg_asb)) { ++ dev_err(dev, "Failed to map ARGON ASB: %ld\n", ++ PTR_ERR(pm->arg_asb)); ++ return PTR_ERR(pm->arg_asb); ++ } ++ } ++ + /* We'll use the presence of the AXI ASB regs in the + * bcm2835-pm binding as the key for whether we can reference + * the full PM register range and support power domains. +--- a/drivers/soc/bcm/bcm2835-power.c ++++ b/drivers/soc/bcm/bcm2835-power.c +@@ -143,6 +143,8 @@ struct bcm2835_power { + /* AXI Async bridge registers. */ + void __iomem *asb; + ++ bool is_2711; ++ + struct genpd_onecell_data pd_xlate; + struct bcm2835_power_domain domains[BCM2835_POWER_DOMAIN_COUNT]; + struct reset_controller_dev reset; +@@ -192,6 +194,10 @@ static int bcm2835_power_power_off(struc + { + struct bcm2835_power *power = pd->power; + ++ /* 2711 has no power domains above the reset controller. */ ++ if (power->is_2711) ++ return 0; ++ + /* Enable functional isolation */ + PM_WRITE(pm_reg, PM_READ(pm_reg) & ~PM_ISFUNC); + +@@ -213,6 +219,10 @@ static int bcm2835_power_power_on(struct + int inrush; + bool powok; + ++ /* 2711 has no power domains above the reset controller. */ ++ if (power->is_2711) ++ return 0; ++ + /* If it was already powered on by the fw, leave it that way. */ + if (PM_READ(pm_reg) & PM_POWUP) + return 0; +@@ -627,6 +637,18 @@ static int bcm2835_power_probe(struct pl + power->base = pm->base; + power->asb = pm->asb; + ++ /* 2711 hack: the new ARGON ASB took over V3D, which is our ++ * only consumer of this driver so far. The old ASB seems to ++ * still be present with ISP and H264 bits but no V3D, but I ++ * don't know if that's real or not. The V3D is in the same ++ * place in the new ASB as the old one, so just poke the new ++ * one for now. ++ */ ++ if (pm->arg_asb) { ++ power->asb = pm->arg_asb; ++ power->is_2711 = true; ++ } ++ + id = ASB_READ(ASB_AXI_BRDG_ID); + if (id != 0x62726467 /* "BRDG" */) { + dev_err(dev, "ASB register ID returned 0x%08x\n", id); +--- a/include/linux/mfd/bcm2835-pm.h ++++ b/include/linux/mfd/bcm2835-pm.h +@@ -9,6 +9,7 @@ struct bcm2835_pm { + struct device *dev; + void __iomem *base; + void __iomem *asb; ++ void __iomem *arg_asb; + }; + + #endif /* BCM2835_MFD_PM_H */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0136-clk-bcm2835-Add-support-for-setting-leaf-clock-rates.patch b/target/linux/bcm27xx/patches-5.10/950-0136-clk-bcm2835-Add-support-for-setting-leaf-clock-rates.patch new file mode 100644 index 0000000000..4ad140bbbb --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0136-clk-bcm2835-Add-support-for-setting-leaf-clock-rates.patch @@ -0,0 +1,53 @@ +From a1dcaba80910c0196b6e51111ba3890372067e0e Mon Sep 17 00:00:00 2001 +From: Eric Anholt +Date: Thu, 2 May 2019 15:11:05 -0700 +Subject: [PATCH] clk: bcm2835: Add support for setting leaf clock + rates while running. + +As long as you wait for !BUSY, you can do glitch-free updates of clock +rate while the clock is running. + +Signed-off-by: Eric Anholt +--- + drivers/clk/bcm/clk-bcm2835.c | 22 +++++++++++++--------- + 1 file changed, 13 insertions(+), 9 deletions(-) + +--- a/drivers/clk/bcm/clk-bcm2835.c ++++ b/drivers/clk/bcm/clk-bcm2835.c +@@ -1115,15 +1115,19 @@ static int bcm2835_clock_set_rate(struct + + spin_lock(&cprman->regs_lock); + +- /* +- * Setting up frac support +- * +- * In principle it is recommended to stop/start the clock first, +- * but as we set CLK_SET_RATE_GATE during registration of the +- * clock this requirement should be take care of by the +- * clk-framework. ++ ctl = cprman_read(cprman, data->ctl_reg); ++ ++ /* If the clock is running, we have to pause clock generation while ++ * updating the control and div regs. This is glitchless (no clock ++ * signals generated faster than the rate) but each reg access is two ++ * OSC cycles so the clock will slow down for a moment. + */ +- ctl = cprman_read(cprman, data->ctl_reg) & ~CM_FRAC; ++ if (ctl & CM_ENABLE) { ++ cprman_write(cprman, data->ctl_reg, ctl & ~CM_ENABLE); ++ bcm2835_clock_wait_busy(clock); ++ } ++ ++ ctl &= ~CM_FRAC; + ctl |= (div & CM_DIV_FRAC_MASK) ? CM_FRAC : 0; + cprman_write(cprman, data->ctl_reg, ctl); + +@@ -1499,7 +1503,7 @@ static struct clk_hw *bcm2835_register_c + init.ops = &bcm2835_vpu_clock_clk_ops; + } else { + init.ops = &bcm2835_clock_clk_ops; +- init.flags |= CLK_SET_RATE_GATE | CLK_SET_PARENT_GATE; ++ init.flags |= CLK_SET_PARENT_GATE; + + /* If the clock wasn't actually enabled at boot, it's not + * critical. diff --git a/target/linux/bcm27xx/patches-5.10/950-0137-clk-bcm2835-Allow-reparenting-leaf-clocks-while-they.patch b/target/linux/bcm27xx/patches-5.10/950-0137-clk-bcm2835-Allow-reparenting-leaf-clocks-while-they.patch new file mode 100644 index 0000000000..093548898d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0137-clk-bcm2835-Allow-reparenting-leaf-clocks-while-they.patch @@ -0,0 +1,71 @@ +From c6c55ad6f9269c703e8b7f9832640dbc0390238a Mon Sep 17 00:00:00 2001 +From: Eric Anholt +Date: Thu, 2 May 2019 15:24:04 -0700 +Subject: [PATCH] clk: bcm2835: Allow reparenting leaf clocks while + they're running. + +This falls under the same "we can reprogram glitch-free as long as we +pause generation" rule as updating the div/frac fields. This can be +used for runtime reclocking of V3D to manage power leakage. + +Signed-off-by: Eric Anholt +--- + drivers/clk/bcm/clk-bcm2835.c | 19 ++++++++++++++++--- + 1 file changed, 16 insertions(+), 3 deletions(-) + +--- a/drivers/clk/bcm/clk-bcm2835.c ++++ b/drivers/clk/bcm/clk-bcm2835.c +@@ -1104,8 +1104,10 @@ static int bcm2835_clock_on(struct clk_h + return 0; + } + +-static int bcm2835_clock_set_rate(struct clk_hw *hw, +- unsigned long rate, unsigned long parent_rate) ++static int bcm2835_clock_set_rate_and_parent(struct clk_hw *hw, ++ unsigned long rate, ++ unsigned long parent_rate, ++ u8 parent) + { + struct bcm2835_clock *clock = bcm2835_clock_from_hw(hw); + struct bcm2835_cprman *cprman = clock->cprman; +@@ -1127,6 +1129,11 @@ static int bcm2835_clock_set_rate(struct + bcm2835_clock_wait_busy(clock); + } + ++ if (parent != 0xff) { ++ ctl &= ~(CM_SRC_MASK << CM_SRC_SHIFT); ++ ctl |= parent << CM_SRC_SHIFT; ++ } ++ + ctl &= ~CM_FRAC; + ctl |= (div & CM_DIV_FRAC_MASK) ? CM_FRAC : 0; + cprman_write(cprman, data->ctl_reg, ctl); +@@ -1138,6 +1145,12 @@ static int bcm2835_clock_set_rate(struct + return 0; + } + ++static int bcm2835_clock_set_rate(struct clk_hw *hw, ++ unsigned long rate, unsigned long parent_rate) ++{ ++ return bcm2835_clock_set_rate_and_parent(hw, rate, parent_rate, 0xff); ++} ++ + static bool + bcm2835_clk_is_pllc(struct clk_hw *hw) + { +@@ -1321,6 +1334,7 @@ static const struct clk_ops bcm2835_cloc + .unprepare = bcm2835_clock_off, + .recalc_rate = bcm2835_clock_get_rate, + .set_rate = bcm2835_clock_set_rate, ++ .set_rate_and_parent = bcm2835_clock_set_rate_and_parent, + .determine_rate = bcm2835_clock_determine_rate, + .set_parent = bcm2835_clock_set_parent, + .get_parent = bcm2835_clock_get_parent, +@@ -1503,7 +1517,6 @@ static struct clk_hw *bcm2835_register_c + init.ops = &bcm2835_vpu_clock_clk_ops; + } else { + init.ops = &bcm2835_clock_clk_ops; +- init.flags |= CLK_SET_PARENT_GATE; + + /* If the clock wasn't actually enabled at boot, it's not + * critical. diff --git a/target/linux/bcm27xx/patches-5.10/950-0138-usb-add-plumbing-for-updating-interrupt-endpoint-int.patch b/target/linux/bcm27xx/patches-5.10/950-0138-usb-add-plumbing-for-updating-interrupt-endpoint-int.patch new file mode 100644 index 0000000000..886899267e --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0138-usb-add-plumbing-for-updating-interrupt-endpoint-int.patch @@ -0,0 +1,104 @@ +From e1cd62d5163e73d18b4e3083a8a09dfb9c67fd4b Mon Sep 17 00:00:00 2001 +From: Jonathan Bell +Date: Tue, 11 Jun 2019 10:55:00 +0100 +Subject: [PATCH] usb: add plumbing for updating interrupt endpoint + interval state + +xHCI caches device and endpoint data after the interface is configured, +so an explicit command needs to be issued for any device driver wanting +to alter the polling interval of an endpoint. + +Add usb_fixup_endpoint() to allow drivers to do this. The fixup must be +called after calculating endpoint bandwidth requirements but before any +URBs are submitted. + +If polling intervals are shortened, any bandwidth reservations are no +longer valid but in practice polling intervals are only ever relaxed. + +Limit the scope to interrupt transfers for now. + +Signed-off-by: Jonathan Bell +--- + drivers/usb/core/hcd.c | 10 ++++++++++ + drivers/usb/core/message.c | 15 +++++++++++++++ + include/linux/usb.h | 2 ++ + include/linux/usb/hcd.h | 7 +++++++ + 4 files changed, 34 insertions(+) + +--- a/drivers/usb/core/hcd.c ++++ b/drivers/usb/core/hcd.c +@@ -1945,6 +1945,16 @@ reset: + return ret; + } + ++void usb_hcd_fixup_endpoint(struct usb_device *udev, ++ struct usb_host_endpoint *ep, int interval) ++{ ++ struct usb_hcd *hcd; ++ ++ hcd = bus_to_hcd(udev->bus); ++ if (hcd->driver->fixup_endpoint) ++ hcd->driver->fixup_endpoint(hcd, udev, ep, interval); ++} ++ + /* Disables the endpoint: synchronizes with the hcd to make sure all + * endpoint state is gone from hardware. usb_hcd_flush_endpoint() must + * have been called previously. Use for set_configuration, set_interface, +--- a/drivers/usb/core/message.c ++++ b/drivers/usb/core/message.c +@@ -1259,6 +1259,21 @@ static void remove_intf_ep_devs(struct u + intf->ep_devs_created = 0; + } + ++void usb_fixup_endpoint(struct usb_device *dev, int epaddr, int interval) ++{ ++ unsigned int epnum = epaddr & USB_ENDPOINT_NUMBER_MASK; ++ struct usb_host_endpoint *ep; ++ ++ if (usb_endpoint_out(epaddr)) ++ ep = dev->ep_out[epnum]; ++ else ++ ep = dev->ep_in[epnum]; ++ ++ if (ep && usb_endpoint_xfer_int(&ep->desc)) ++ usb_hcd_fixup_endpoint(dev, ep, interval); ++} ++EXPORT_SYMBOL_GPL(usb_fixup_endpoint); ++ + /** + * usb_disable_endpoint -- Disable an endpoint by address + * @dev: the device whose endpoint is being disabled +--- a/include/linux/usb.h ++++ b/include/linux/usb.h +@@ -1838,6 +1838,8 @@ extern int usb_clear_halt(struct usb_dev + extern int usb_reset_configuration(struct usb_device *dev); + extern int usb_set_interface(struct usb_device *dev, int ifnum, int alternate); + extern void usb_reset_endpoint(struct usb_device *dev, unsigned int epaddr); ++extern void usb_fixup_endpoint(struct usb_device *dev, int epaddr, ++ int interval); + + /* this request isn't really synchronous, but it belongs with the others */ + extern int usb_driver_set_configuration(struct usb_device *udev, int config); +--- a/include/linux/usb/hcd.h ++++ b/include/linux/usb/hcd.h +@@ -382,6 +382,11 @@ struct hc_driver { + * or bandwidth constraints. + */ + void (*reset_bandwidth)(struct usb_hcd *, struct usb_device *); ++ /* Override the endpoint-derived interval ++ * (if there is any cached hardware state). ++ */ ++ void (*fixup_endpoint)(struct usb_hcd *hcd, struct usb_device *udev, ++ struct usb_host_endpoint *ep, int interval); + /* Returns the hardware-chosen device address */ + int (*address_device)(struct usb_hcd *, struct usb_device *udev); + /* prepares the hardware to send commands to the device */ +@@ -443,6 +448,8 @@ extern void usb_hcd_unmap_urb_setup_for_ + extern void usb_hcd_unmap_urb_for_dma(struct usb_hcd *, struct urb *); + extern void usb_hcd_flush_endpoint(struct usb_device *udev, + struct usb_host_endpoint *ep); ++extern void usb_hcd_fixup_endpoint(struct usb_device *udev, ++ struct usb_host_endpoint *ep, int interval); + extern void usb_hcd_disable_endpoint(struct usb_device *udev, + struct usb_host_endpoint *ep); + extern void usb_hcd_reset_endpoint(struct usb_device *udev, diff --git a/target/linux/bcm27xx/patches-5.10/950-0139-xhci-implement-xhci_fixup_endpoint-for-interval-adju.patch b/target/linux/bcm27xx/patches-5.10/950-0139-xhci-implement-xhci_fixup_endpoint-for-interval-adju.patch new file mode 100644 index 0000000000..406bb04d46 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0139-xhci-implement-xhci_fixup_endpoint-for-interval-adju.patch @@ -0,0 +1,129 @@ +From 574aabfd5a408bc10da01bb4abe222abc013ea45 Mon Sep 17 00:00:00 2001 +From: Jonathan Bell +Date: Tue, 11 Jun 2019 11:33:39 +0100 +Subject: [PATCH] xhci: implement xhci_fixup_endpoint for interval + adjustments + +Must be called in a non-atomic context, after the endpoint +has been registered with the hardware via xhci_add_endpoint +and before the first URB is submitted for the endpoint. + +Signed-off-by: Jonathan Bell +--- + drivers/usb/host/xhci.c | 98 +++++++++++++++++++++++++++++++++++++++++ + 1 file changed, 98 insertions(+) + +--- a/drivers/usb/host/xhci.c ++++ b/drivers/usb/host/xhci.c +@@ -1467,6 +1467,103 @@ command_cleanup: + } + + /* ++ * RPI: Fixup endpoint intervals when requested ++ * - Check interval versus the (cached) endpoint context ++ * - set the endpoint interval to the new value ++ * - force an endpoint configure command ++ * XXX: bandwidth is not recalculated. We should probably do that. ++ */ ++static void xhci_fixup_endpoint(struct usb_hcd *hcd, struct usb_device *udev, ++ struct usb_host_endpoint *ep, int interval) ++{ ++ struct xhci_hcd *xhci; ++ struct xhci_ep_ctx *ep_ctx_out, *ep_ctx_in; ++ struct xhci_command *command; ++ struct xhci_input_control_ctx *ctrl_ctx; ++ struct xhci_virt_device *vdev; ++ int xhci_interval; ++ int ret; ++ int ep_index; ++ unsigned long flags; ++ u32 ep_info_tmp; ++ ++ xhci = hcd_to_xhci(hcd); ++ ep_index = xhci_get_endpoint_index(&ep->desc); ++ ++ /* FS/LS interval translations */ ++ if ((udev->speed == USB_SPEED_FULL || ++ udev->speed == USB_SPEED_LOW)) ++ interval *= 8; ++ ++ mutex_lock(&xhci->mutex); ++ ++ spin_lock_irqsave(&xhci->lock, flags); ++ ++ vdev = xhci->devs[udev->slot_id]; ++ /* Get context-derived endpoint interval */ ++ ep_ctx_out = xhci_get_ep_ctx(xhci, vdev->out_ctx, ep_index); ++ ep_ctx_in = xhci_get_ep_ctx(xhci, vdev->in_ctx, ep_index); ++ xhci_interval = EP_INTERVAL_TO_UFRAMES(le32_to_cpu(ep_ctx_out->ep_info)); ++ ++ if (interval == xhci_interval) { ++ spin_unlock_irqrestore(&xhci->lock, flags); ++ mutex_unlock(&xhci->mutex); ++ return; ++ } ++ ++ xhci_dbg(xhci, "Fixup interval=%d xhci_interval=%d\n", ++ interval, xhci_interval); ++ command = xhci_alloc_command_with_ctx(xhci, true, GFP_ATOMIC); ++ if (!command) { ++ /* Failure here is benign, poll at the original rate */ ++ spin_unlock_irqrestore(&xhci->lock, flags); ++ mutex_unlock(&xhci->mutex); ++ return; ++ } ++ ++ /* xHCI uses exponents for intervals... */ ++ xhci_interval = fls(interval) - 1; ++ xhci_interval = clamp_val(xhci_interval, 3, 10); ++ ep_info_tmp = le32_to_cpu(ep_ctx_out->ep_info); ++ ep_info_tmp &= ~EP_INTERVAL(255); ++ ep_info_tmp |= EP_INTERVAL(xhci_interval); ++ ++ /* Keep the endpoint context up-to-date while issuing the command. */ ++ xhci_endpoint_copy(xhci, vdev->in_ctx, ++ vdev->out_ctx, ep_index); ++ ep_ctx_in->ep_info = cpu_to_le32(ep_info_tmp); ++ ++ /* ++ * We need to drop the lock, so take an explicit copy ++ * of the ep context. ++ */ ++ xhci_endpoint_copy(xhci, command->in_ctx, vdev->in_ctx, ep_index); ++ ++ ctrl_ctx = xhci_get_input_control_ctx(command->in_ctx); ++ if (!ctrl_ctx) { ++ xhci_warn(xhci, ++ "%s: Could not get input context, bad type.\n", ++ __func__); ++ spin_unlock_irqrestore(&xhci->lock, flags); ++ xhci_free_command(xhci, command); ++ mutex_unlock(&xhci->mutex); ++ return; ++ } ++ ctrl_ctx->add_flags = xhci_get_endpoint_flag_from_index(ep_index); ++ ctrl_ctx->drop_flags = 0; ++ ++ spin_unlock_irqrestore(&xhci->lock, flags); ++ ++ ret = xhci_configure_endpoint(xhci, udev, command, ++ false, false); ++ if (ret) ++ xhci_warn(xhci, "%s: Configure endpoint failed: %d\n", ++ __func__, ret); ++ xhci_free_command(xhci, command); ++ mutex_unlock(&xhci->mutex); ++} ++ ++/* + * non-error returns are a promise to giveback() the urb later + * we drop ownership so next owner (or urb unlink) can get it + */ +@@ -5361,6 +5458,7 @@ static const struct hc_driver xhci_hc_dr + .endpoint_reset = xhci_endpoint_reset, + .check_bandwidth = xhci_check_bandwidth, + .reset_bandwidth = xhci_reset_bandwidth, ++ .fixup_endpoint = xhci_fixup_endpoint, + .address_device = xhci_address_device, + .enable_device = xhci_enable_device, + .update_hub_device = xhci_update_hub_device, diff --git a/target/linux/bcm27xx/patches-5.10/950-0140-usbhid-call-usb_fixup_endpoint-after-mangling-interv.patch b/target/linux/bcm27xx/patches-5.10/950-0140-usbhid-call-usb_fixup_endpoint-after-mangling-interv.patch new file mode 100644 index 0000000000..332139dadb --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0140-usbhid-call-usb_fixup_endpoint-after-mangling-interv.patch @@ -0,0 +1,23 @@ +From 39deae2e4d179df6532687902948a84c39bb2f34 Mon Sep 17 00:00:00 2001 +From: Jonathan Bell +Date: Tue, 11 Jun 2019 11:42:03 +0100 +Subject: [PATCH] usbhid: call usb_fixup_endpoint after mangling + intervals + +Lets the mousepoll override mechanism work with xhci. + +Signed-off-by: Jonathan Bell +--- + drivers/hid/usbhid/hid-core.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/hid/usbhid/hid-core.c ++++ b/drivers/hid/usbhid/hid-core.c +@@ -1128,6 +1128,7 @@ static int usbhid_start(struct hid_devic + interval = hid_kbpoll_interval; + break; + } ++ usb_fixup_endpoint(dev, endpoint->bEndpointAddress, interval); + + ret = -ENOMEM; + if (usb_endpoint_dir_in(endpoint)) { diff --git a/target/linux/bcm27xx/patches-5.10/950-0141-arm-bcm2835-Add-bcm2838-compatible-string.patch b/target/linux/bcm27xx/patches-5.10/950-0141-arm-bcm2835-Add-bcm2838-compatible-string.patch new file mode 100644 index 0000000000..c83d117997 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0141-arm-bcm2835-Add-bcm2838-compatible-string.patch @@ -0,0 +1,20 @@ +From a085d0f6d2eddd876becfbc6b658fd1d6db5cd0b Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 11 Jun 2019 17:38:28 +0100 +Subject: [PATCH] arm: bcm2835: Add bcm2838 compatible string. + +Signed-off-by: Phil Elwell +--- + arch/arm/mach-bcm/board_bcm2835.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/arch/arm/mach-bcm/board_bcm2835.c ++++ b/arch/arm/mach-bcm/board_bcm2835.c +@@ -109,6 +109,7 @@ static const char * const bcm2835_compat + #ifdef CONFIG_ARCH_MULTI_V7 + "brcm,bcm2836", + "brcm,bcm2837", ++ "brcm,bcm2838", + #endif + NULL + }; diff --git a/target/linux/bcm27xx/patches-5.10/950-0142-drm-v3d-Add-support-for-2711.patch b/target/linux/bcm27xx/patches-5.10/950-0142-drm-v3d-Add-support-for-2711.patch new file mode 100644 index 0000000000..e11eee95e8 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0142-drm-v3d-Add-support-for-2711.patch @@ -0,0 +1,20 @@ +From c124b2797bc42c9363345581e233a53d811d72af Mon Sep 17 00:00:00 2001 +From: Eric Anholt +Date: Thu, 4 Oct 2018 17:22:43 -0700 +Subject: [PATCH] drm/v3d: Add support for 2711. + +Signed-off-by: Eric Anholt +--- + drivers/gpu/drm/v3d/v3d_drv.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/gpu/drm/v3d/v3d_drv.c ++++ b/drivers/gpu/drm/v3d/v3d_drv.c +@@ -227,6 +227,7 @@ static struct drm_driver v3d_drm_driver + static const struct of_device_id v3d_of_match[] = { + { .compatible = "brcm,7268-v3d" }, + { .compatible = "brcm,7278-v3d" }, ++ { .compatible = "brcm,2711-v3d" }, + {}, + }; + MODULE_DEVICE_TABLE(of, v3d_of_match); diff --git a/target/linux/bcm27xx/patches-5.10/950-0143-drm-v3d-Skip-MMU-flush-if-the-device-is-currently-of.patch b/target/linux/bcm27xx/patches-5.10/950-0143-drm-v3d-Skip-MMU-flush-if-the-device-is-currently-of.patch new file mode 100644 index 0000000000..1276cf5b52 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0143-drm-v3d-Skip-MMU-flush-if-the-device-is-currently-of.patch @@ -0,0 +1,52 @@ +From ca945515e1a3be554e654823d6a27403d43318c2 Mon Sep 17 00:00:00 2001 +From: Eric Anholt +Date: Mon, 14 Jan 2019 12:35:43 -0800 +Subject: [PATCH] drm/v3d: Skip MMU flush if the device is currently + off. + +If it's off, we know it will be reset on poweron, so the MMU won't +have any TLB cached from before this point. Avoids failed waits for +MMU flush to reply. + +Signed-off-by: Eric Anholt +(cherry picked from commit 3ee4e2e0a9e9587eacbb69b067bbc72ab2cdc47b) +--- + drivers/gpu/drm/v3d/v3d_mmu.c | 13 +++++++++++++ + 1 file changed, 13 insertions(+) + +--- a/drivers/gpu/drm/v3d/v3d_mmu.c ++++ b/drivers/gpu/drm/v3d/v3d_mmu.c +@@ -18,6 +18,8 @@ + * each client. This is not yet implemented. + */ + ++#include ++ + #include "v3d_drv.h" + #include "v3d_regs.h" + +@@ -34,6 +36,14 @@ static int v3d_mmu_flush_all(struct v3d_ + { + int ret; + ++ /* Keep power on the device on until we're done with this ++ * call, but skip the flush if the device is off and will be ++ * reset when powered back on. ++ */ ++ ret = pm_runtime_get_if_in_use(v3d->dev); ++ if (ret == 0) ++ return 0; ++ + /* Make sure that another flush isn't already running when we + * start this one. + */ +@@ -61,6 +71,9 @@ static int v3d_mmu_flush_all(struct v3d_ + if (ret) + dev_err(v3d->drm.dev, "MMUC flush wait idle failed\n"); + ++ pm_runtime_mark_last_busy(v3d->dev); ++ pm_runtime_put_autosuspend(v3d->dev); ++ + return ret; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0144-drm-v3d-Hook-up-the-runtime-PM-ops.patch b/target/linux/bcm27xx/patches-5.10/950-0144-drm-v3d-Hook-up-the-runtime-PM-ops.patch new file mode 100644 index 0000000000..9fcffec0b0 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0144-drm-v3d-Hook-up-the-runtime-PM-ops.patch @@ -0,0 +1,34 @@ +From e7398ddc64a8540bb016d653ff0bddfc0660f606 Mon Sep 17 00:00:00 2001 +From: Eric Anholt +Date: Mon, 14 Jan 2019 14:47:57 -0800 +Subject: [PATCH] drm/v3d: Hook up the runtime PM ops. + +In translating the runtime PM code from vc4, I missed the ".pm" +assignment to actually connect them up. Fixes missing MMU setup if +runtime PM resets V3D. + +Signed-off-by: Eric Anholt +(cherry picked from commit ca197699af29baa8236c74c53d4904ca8957ee06) +--- + drivers/gpu/drm/v3d/v3d_drv.c | 3 ++- + 1 file changed, 2 insertions(+), 1 deletion(-) + +--- a/drivers/gpu/drm/v3d/v3d_drv.c ++++ b/drivers/gpu/drm/v3d/v3d_drv.c +@@ -70,7 +70,7 @@ static int v3d_runtime_resume(struct dev + } + #endif + +-static const struct dev_pm_ops v3d_v3d_pm_ops = { ++static const struct dev_pm_ops v3d_pm_ops = { + SET_RUNTIME_PM_OPS(v3d_runtime_suspend, v3d_runtime_resume, NULL) + }; + +@@ -356,6 +356,7 @@ static struct platform_driver v3d_platfo + .driver = { + .name = "v3d", + .of_match_table = v3d_of_match, ++ .pm = &v3d_pm_ops, + }, + }; + diff --git a/target/linux/bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch b/target/linux/bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch new file mode 100644 index 0000000000..59a1cf11bd --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch @@ -0,0 +1,90 @@ +From e47ad4978bde4920c1e1eb381531a6904025c852 Mon Sep 17 00:00:00 2001 +From: Jonathan Bell +Date: Thu, 11 Jul 2019 17:55:43 +0100 +Subject: [PATCH] xhci: add quirk for host controllers that don't + update endpoint DCS + +Seen on a VLI VL805 PCIe to USB controller. For non-stream endpoints +at least, if the xHC halts on a particular TRB due to an error then +the DCS field in the Out Endpoint Context maintained by the hardware +is not updated with the current cycle state. + +Using the quirk XHCI_EP_CTX_BROKEN_DCS and instead fetch the DCS bit +from the TRB that the xHC stopped on. + +See: https://github.com/raspberrypi/linux/issues/3060 + +Signed-off-by: Jonathan Bell +--- + drivers/usb/host/xhci-pci.c | 4 +++- + drivers/usb/host/xhci-ring.c | 26 +++++++++++++++++++++++++- + drivers/usb/host/xhci.h | 1 + + 3 files changed, 29 insertions(+), 2 deletions(-) + +--- a/drivers/usb/host/xhci-pci.c ++++ b/drivers/usb/host/xhci-pci.c +@@ -274,8 +274,10 @@ static void xhci_pci_quirks(struct devic + pdev->device == 0x3432) + xhci->quirks |= XHCI_BROKEN_STREAMS; + +- if (pdev->vendor == PCI_VENDOR_ID_VIA && pdev->device == 0x3483) ++ if (pdev->vendor == PCI_VENDOR_ID_VIA && pdev->device == 0x3483) { + xhci->quirks |= XHCI_LPM_SUPPORT; ++ xhci->quirks |= XHCI_EP_CTX_BROKEN_DCS; ++ } + + if (pdev->vendor == PCI_VENDOR_ID_ASMEDIA && + pdev->device == PCI_DEVICE_ID_ASMEDIA_1042_XHCI) +--- a/drivers/usb/host/xhci-ring.c ++++ b/drivers/usb/host/xhci-ring.c +@@ -556,7 +556,10 @@ void xhci_find_new_dequeue_state(struct + struct xhci_virt_ep *ep = &dev->eps[ep_index]; + struct xhci_ring *ep_ring; + struct xhci_segment *new_seg; ++ struct xhci_segment *halted_seg = NULL; + union xhci_trb *new_deq; ++ union xhci_trb *halted_trb; ++ int index = 0; + dma_addr_t addr; + u64 hw_dequeue; + bool cycle_found = false; +@@ -594,7 +597,28 @@ void xhci_find_new_dequeue_state(struct + hw_dequeue = xhci_get_hw_deq(xhci, dev, ep_index, stream_id); + new_seg = ep_ring->deq_seg; + new_deq = ep_ring->dequeue; +- state->new_cycle_state = hw_dequeue & 0x1; ++ ++ /* ++ * Quirk: xHC write-back of the DCS field in the hardware dequeue ++ * pointer is wrong - use the cycle state of the TRB pointed to by ++ * the dequeue pointer. ++ */ ++ if (xhci->quirks & XHCI_EP_CTX_BROKEN_DCS && ++ !(ep->ep_state & EP_HAS_STREAMS)) ++ halted_seg = trb_in_td(xhci, cur_td->start_seg, ++ cur_td->first_trb, cur_td->last_trb, ++ hw_dequeue & ~0xf, false); ++ if (halted_seg) { ++ index = ((dma_addr_t)(hw_dequeue & ~0xf) - halted_seg->dma) / ++ sizeof(*halted_trb); ++ halted_trb = &halted_seg->trbs[index]; ++ state->new_cycle_state = halted_trb->generic.field[3] & 0x1; ++ xhci_dbg(xhci, "Endpoint DCS = %d TRB index = %d cycle = %d\n", ++ (u8)(hw_dequeue & 0x1), index, ++ state->new_cycle_state); ++ } else { ++ state->new_cycle_state = hw_dequeue & 0x1; ++ } + state->stream_id = stream_id; + + /* +--- a/drivers/usb/host/xhci.h ++++ b/drivers/usb/host/xhci.h +@@ -1881,6 +1881,7 @@ struct xhci_hcd { + #define XHCI_DISABLE_SPARSE BIT_ULL(38) + #define XHCI_SG_TRB_CACHE_SIZE_QUIRK BIT_ULL(39) + #define XHCI_NO_SOFT_RETRY BIT_ULL(40) ++#define XHCI_EP_CTX_BROKEN_DCS BIT_ULL(41) + + unsigned int num_active_eps; + unsigned int limit_active_eps; diff --git a/target/linux/bcm27xx/patches-5.10/950-0146-i2c-bcm2835-Set-clock-stretch-timeout-to-35ms.patch b/target/linux/bcm27xx/patches-5.10/950-0146-i2c-bcm2835-Set-clock-stretch-timeout-to-35ms.patch new file mode 100644 index 0000000000..9cb93621bb --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0146-i2c-bcm2835-Set-clock-stretch-timeout-to-35ms.patch @@ -0,0 +1,47 @@ +From 930c69b932959ad237347ca02b31bf1e9ebf227a Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 12 Jul 2019 15:38:35 +0100 +Subject: [PATCH] i2c: bcm2835: Set clock-stretch timeout to 35ms + +The BCM2835 I2C blocks have a register to set the clock-stretch +timeout - how long the device is allowed to hold SCL low - in bus +cycles. The current driver doesn't write to the register, therefore +the default value of 64 cycles is being used for all devices. + +Set the timeout to the value recommended for SMBus - 35ms. + +See: https://github.com/raspberrypi/linux/issues/3064 + +Signed-off-by: Phil Elwell +--- + drivers/i2c/busses/i2c-bcm2835.c | 12 ++++++++++++ + 1 file changed, 12 insertions(+) + +--- a/drivers/i2c/busses/i2c-bcm2835.c ++++ b/drivers/i2c/busses/i2c-bcm2835.c +@@ -188,6 +188,7 @@ static int clk_bcm2835_i2c_set_rate(stru + { + struct clk_bcm2835_i2c *div = to_clk_bcm2835_i2c(hw); + u32 redl, fedl; ++ u32 clk_tout; + u32 divider = clk_bcm2835_i2c_calc_divider(rate, parent_rate); + + if (divider == -EINVAL) +@@ -211,6 +212,17 @@ static int clk_bcm2835_i2c_set_rate(stru + bcm2835_i2c_writel(div->i2c_dev, BCM2835_I2C_DEL, + (fedl << BCM2835_I2C_FEDL_SHIFT) | + (redl << BCM2835_I2C_REDL_SHIFT)); ++ ++ /* ++ * Set the clock stretch timeout to the SMBUs-recommended 35ms. ++ */ ++ if (rate > 0xffff*1000/35) ++ clk_tout = 0xffff; ++ else ++ clk_tout = 35*rate/1000; ++ ++ bcm2835_i2c_writel(div->i2c_dev, BCM2835_I2C_CLKT, clk_tout); ++ + return 0; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0147-clk-bcm2835-Avoid-null-pointer-exception.patch b/target/linux/bcm27xx/patches-5.10/950-0147-clk-bcm2835-Avoid-null-pointer-exception.patch new file mode 100644 index 0000000000..29613d1a40 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0147-clk-bcm2835-Avoid-null-pointer-exception.patch @@ -0,0 +1,29 @@ +From 17e36f484c42177981279d791cbc55a43c5d5a12 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Tue, 6 Aug 2019 15:23:14 +0100 +Subject: [PATCH] clk-bcm2835: Avoid null pointer exception + +clk_desc_array[BCM2835_PLLB] doesn't exist so we dereference null when iterating + +Signed-off-by: popcornmix +--- + drivers/clk/bcm/clk-bcm2835.c | 8 +++++--- + 1 file changed, 5 insertions(+), 3 deletions(-) + +--- a/drivers/clk/bcm/clk-bcm2835.c ++++ b/drivers/clk/bcm/clk-bcm2835.c +@@ -2310,9 +2310,11 @@ static bool bcm2835_clk_is_claimed(const + int i; + + for (i = 0; i < ARRAY_SIZE(clk_desc_array); i++) { +- const char *clk_name = *(const char **)(clk_desc_array[i].data); +- if (!strcmp(name, clk_name)) +- return bcm2835_clk_claimed[i]; ++ if (clk_desc_array[i].data) { ++ const char *clk_name = *(const char **)(clk_desc_array[i].data); ++ if (!strcmp(name, clk_name)) ++ return bcm2835_clk_claimed[i]; ++ } + } + + return false; diff --git a/target/linux/bcm27xx/patches-5.10/950-0148-drm-v3d-HACK-gut-runtime-pm-for-now.patch b/target/linux/bcm27xx/patches-5.10/950-0148-drm-v3d-HACK-gut-runtime-pm-for-now.patch new file mode 100644 index 0000000000..d986de4dd3 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0148-drm-v3d-HACK-gut-runtime-pm-for-now.patch @@ -0,0 +1,109 @@ +From 1480a99bfef66b0c0f07c90436a873937b656ce7 Mon Sep 17 00:00:00 2001 +From: Eric Anholt +Date: Mon, 14 Jan 2019 15:13:17 -0800 +Subject: [PATCH] drm/v3d: HACK: gut runtime pm for now. + +Something is still unstable -- on starting a new glxgears from an idle +X11, I get an MMU violation in high addresses. The CTS also failed +quite quickly. With this, CTS progresses for an hour before OOMing +(allocating some big buffers when my board only has 600MB available to +Linux) + +Signed-off-by: Eric Anholt +--- + drivers/gpu/drm/v3d/v3d_debugfs.c | 16 +--------------- + drivers/gpu/drm/v3d/v3d_drv.c | 9 --------- + 2 files changed, 1 insertion(+), 24 deletions(-) + +--- a/drivers/gpu/drm/v3d/v3d_debugfs.c ++++ b/drivers/gpu/drm/v3d/v3d_debugfs.c +@@ -4,7 +4,6 @@ + #include + #include + #include +-#include + #include + + #include +@@ -130,11 +129,8 @@ static int v3d_v3d_debugfs_ident(struct + struct drm_device *dev = node->minor->dev; + struct v3d_dev *v3d = to_v3d_dev(dev); + u32 ident0, ident1, ident2, ident3, cores; +- int ret, core; ++ int core; + +- ret = pm_runtime_get_sync(v3d->drm.dev); +- if (ret < 0) +- return ret; + + ident0 = V3D_READ(V3D_HUB_IDENT0); + ident1 = V3D_READ(V3D_HUB_IDENT1); +@@ -187,9 +183,6 @@ static int v3d_v3d_debugfs_ident(struct + (misccfg & V3D_MISCCFG_OVRTMUOUT) != 0); + } + +- pm_runtime_mark_last_busy(v3d->drm.dev); +- pm_runtime_put_autosuspend(v3d->drm.dev); +- + return 0; + } + +@@ -217,11 +210,6 @@ static int v3d_measure_clock(struct seq_ + uint32_t cycles; + int core = 0; + int measure_ms = 1000; +- int ret; +- +- ret = pm_runtime_get_sync(v3d->drm.dev); +- if (ret < 0) +- return ret; + + if (v3d->ver >= 40) { + V3D_CORE_WRITE(core, V3D_V4_PCTR_0_SRC_0_3, +@@ -245,8 +233,6 @@ static int v3d_measure_clock(struct seq_ + cycles / (measure_ms * 1000), + (cycles / (measure_ms * 100)) % 10); + +- pm_runtime_mark_last_busy(v3d->drm.dev); +- pm_runtime_put_autosuspend(v3d->drm.dev); + + return 0; + } +--- a/drivers/gpu/drm/v3d/v3d_drv.c ++++ b/drivers/gpu/drm/v3d/v3d_drv.c +@@ -79,7 +79,6 @@ static int v3d_get_param_ioctl(struct dr + { + struct v3d_dev *v3d = to_v3d_dev(dev); + struct drm_v3d_get_param *args = data; +- int ret; + static const u32 reg_map[] = { + [DRM_V3D_PARAM_V3D_UIFCFG] = V3D_HUB_UIFCFG, + [DRM_V3D_PARAM_V3D_HUB_IDENT1] = V3D_HUB_IDENT1, +@@ -105,17 +104,12 @@ static int v3d_get_param_ioctl(struct dr + if (args->value != 0) + return -EINVAL; + +- ret = pm_runtime_get_sync(v3d->drm.dev); +- if (ret < 0) +- return ret; + if (args->param >= DRM_V3D_PARAM_V3D_CORE0_IDENT0 && + args->param <= DRM_V3D_PARAM_V3D_CORE0_IDENT2) { + args->value = V3D_CORE_READ(0, offset); + } else { + args->value = V3D_READ(offset); + } +- pm_runtime_mark_last_busy(v3d->drm.dev); +- pm_runtime_put_autosuspend(v3d->drm.dev); + return 0; + } + +@@ -308,9 +302,6 @@ static int v3d_platform_drm_probe(struct + return -ENOMEM; + } + +- pm_runtime_use_autosuspend(dev); +- pm_runtime_set_autosuspend_delay(dev, 50); +- pm_runtime_enable(dev); + + ret = v3d_gem_init(drm); + if (ret) diff --git a/target/linux/bcm27xx/patches-5.10/950-0149-drm-v3d-Clock-V3D-down-when-not-in-use.patch b/target/linux/bcm27xx/patches-5.10/950-0149-drm-v3d-Clock-V3D-down-when-not-in-use.patch new file mode 100644 index 0000000000..652207e5e1 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0149-drm-v3d-Clock-V3D-down-when-not-in-use.patch @@ -0,0 +1,161 @@ +From 6a9c9cba52a98a3ca380d43c5a12ef4fc190276d Mon Sep 17 00:00:00 2001 +From: Eric Anholt +Date: Thu, 2 May 2019 13:22:53 -0700 +Subject: [PATCH] drm/v3d: Clock V3D down when not in use. + +My various attempts at re-enabling runtime PM have failed, so just +crank the clock down when V3D is idle to reduce power consumption. + +Signed-off-by: Eric Anholt +--- + drivers/gpu/drm/v3d/v3d_drv.c | 18 ++++++++++++ + drivers/gpu/drm/v3d/v3d_drv.h | 6 ++++ + drivers/gpu/drm/v3d/v3d_gem.c | 53 +++++++++++++++++++++++++++++++---- + 3 files changed, 72 insertions(+), 5 deletions(-) + +--- a/drivers/gpu/drm/v3d/v3d_drv.c ++++ b/drivers/gpu/drm/v3d/v3d_drv.c +@@ -289,6 +289,21 @@ static int v3d_platform_drm_probe(struct + } + } + ++ v3d->clk = devm_clk_get(dev, NULL); ++ if (IS_ERR(v3d->clk)) { ++ if (ret != -EPROBE_DEFER) ++ dev_err(dev, "Failed to get clock\n"); ++ goto dev_free; ++ } ++ v3d->clk_up_rate = clk_get_rate(v3d->clk); ++ /* For downclocking, drop it to the minimum frequency we can get from ++ * the CPRMAN clock generator dividing off our parent. The divider is ++ * 4 bits, but ask for just higher than that so that rounding doesn't ++ * make cprman reject our rate. ++ */ ++ v3d->clk_down_rate = ++ (clk_get_rate(clk_get_parent(v3d->clk)) / (1 << 4)) + 10000; ++ + if (v3d->ver < 41) { + ret = map_regs(v3d, &v3d->gca_regs, "gca"); + if (ret) +@@ -315,6 +330,9 @@ static int v3d_platform_drm_probe(struct + if (ret) + goto irq_disable; + ++ ret = clk_set_rate(v3d->clk, v3d->clk_down_rate); ++ WARN_ON_ONCE(ret != 0); ++ + return 0; + + irq_disable: +--- a/drivers/gpu/drm/v3d/v3d_drv.h ++++ b/drivers/gpu/drm/v3d/v3d_drv.h +@@ -51,6 +51,12 @@ struct v3d_dev { + void __iomem *bridge_regs; + void __iomem *gca_regs; + struct clk *clk; ++ struct delayed_work clk_down_work; ++ unsigned long clk_up_rate, clk_down_rate; ++ struct mutex clk_lock; ++ u32 clk_refcount; ++ bool clk_up; ++ + struct reset_control *reset; + + /* Virtual and DMA addresses of the single shared page table. */ +--- a/drivers/gpu/drm/v3d/v3d_gem.c ++++ b/drivers/gpu/drm/v3d/v3d_gem.c +@@ -4,6 +4,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -19,6 +20,47 @@ + #include "v3d_trace.h" + + static void ++v3d_clock_down_work(struct work_struct *work) ++{ ++ struct v3d_dev *v3d = ++ container_of(work, struct v3d_dev, clk_down_work.work); ++ int ret; ++ ++ ret = clk_set_rate(v3d->clk, v3d->clk_down_rate); ++ v3d->clk_up = false; ++ WARN_ON_ONCE(ret != 0); ++} ++ ++static void ++v3d_clock_up_get(struct v3d_dev *v3d) ++{ ++ mutex_lock(&v3d->clk_lock); ++ if (v3d->clk_refcount++ == 0) { ++ cancel_delayed_work_sync(&v3d->clk_down_work); ++ if (!v3d->clk_up) { ++ int ret; ++ ++ ret = clk_set_rate(v3d->clk, v3d->clk_up_rate); ++ WARN_ON_ONCE(ret != 0); ++ v3d->clk_up = true; ++ } ++ } ++ mutex_unlock(&v3d->clk_lock); ++} ++ ++static void ++v3d_clock_up_put(struct v3d_dev *v3d) ++{ ++ mutex_lock(&v3d->clk_lock); ++ if (--v3d->clk_refcount == 0) { ++ schedule_delayed_work(&v3d->clk_down_work, ++ msecs_to_jiffies(100)); ++ } ++ mutex_unlock(&v3d->clk_lock); ++} ++ ++ ++static void + v3d_init_core(struct v3d_dev *v3d, int core) + { + /* Set OVRTMUOUT, which means that the texture sampler uniform +@@ -354,6 +396,7 @@ v3d_job_free(struct kref *ref) + struct v3d_job *job = container_of(ref, struct v3d_job, refcount); + unsigned long index; + struct dma_fence *fence; ++ struct v3d_dev *v3d = job->v3d; + int i; + + for (i = 0; i < job->bo_count; i++) { +@@ -367,11 +410,7 @@ v3d_job_free(struct kref *ref) + } + xa_destroy(&job->deps); + +- dma_fence_put(job->irq_fence); +- dma_fence_put(job->done_fence); +- +- pm_runtime_mark_last_busy(job->v3d->drm.dev); +- pm_runtime_put_autosuspend(job->v3d->drm.dev); ++ v3d_clock_up_put(v3d); + + kfree(job); + } +@@ -453,6 +492,7 @@ v3d_job_init(struct v3d_dev *v3d, struct + if (ret) + goto fail; + ++ v3d_clock_up_get(v3d); + kref_init(&job->refcount); + + return 0; +@@ -879,6 +919,9 @@ v3d_gem_init(struct drm_device *dev) + mutex_init(&v3d->sched_lock); + mutex_init(&v3d->cache_clean_lock); + ++ mutex_init(&v3d->clk_lock); ++ INIT_DELAYED_WORK(&v3d->clk_down_work, v3d_clock_down_work); ++ + /* Note: We don't allocate address 0. Various bits of HW + * treat 0 as special, such as the occlusion query counters + * where 0 means "disabled". diff --git a/target/linux/bcm27xx/patches-5.10/950-0150-drivers-char-add-chardev-for-mmap-ing-the-RPiVid-con.patch b/target/linux/bcm27xx/patches-5.10/950-0150-drivers-char-add-chardev-for-mmap-ing-the-RPiVid-con.patch new file mode 100644 index 0000000000..0b9a1356d6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0150-drivers-char-add-chardev-for-mmap-ing-the-RPiVid-con.patch @@ -0,0 +1,441 @@ +From e264c7d05860aa12664fa3db8bcf8c4cbc20a62e Mon Sep 17 00:00:00 2001 +From: Jonathan Bell +Date: Thu, 9 May 2019 14:30:37 +0100 +Subject: [PATCH] drivers: char: add chardev for mmap'ing the RPiVid + control registers + +Based on the gpiomem driver, allow mapping of the decoder register +spaces such that userspace can access control/status registers. +This driver is intended for use with a custom ffmpeg backend accelerator +prior to a v4l2 driver being written. + +Signed-off-by: Jonathan Bell + +driver: char: rpivid: Destroy the legacy device on remove + +The legacy name support created a new device that was never destroyed. +If the driver was unloaded and reloaded, it failed due to the +device already existing. + +Fixes: "75f1d14 driver: char: rpivid - also support legacy name" +Signed-off-by: Dave Stevenson + +driver: char: rpivid: Clean up error handling use of ERR_PTR/IS_ERR + +The driver used an unnecessary intermediate void* variable so it +only called ERR_PTR once to convert to the error value. + +Switch to converting as the error arises to remove these intermediate +variables. + +Signed-off-by: Dave Stevenson + +driver: char: rpivid: Add error handling to the legacy device load + +The return value from device_create for the legacy device was never +checked or handled. Add the required error handling. + +Signed-off-by: Dave Stevenson + +driver: char: rpivid: Fix coding style whitespace issues. + +Makes checkpatch happier. + +Signed-off-by: Dave Stevenson + +driver: char: rpimem: Add SPDX licence header. + +Stops checkpatch complaining. + +Signed-off-by: Dave Stevenson + +driver: char: rpivid: Fix access to freed memory + +The error path during probe frees the private memory block, and +then promptly dereferences it to log an error message. + +Use the base device instead of the pointer to it in the private +structure. + +Signed-off-by: Dave Stevenson +--- + drivers/char/broadcom/Kconfig | 8 + + drivers/char/broadcom/Makefile | 1 + + drivers/char/broadcom/rpivid-mem.c | 292 +++++++++++++++++++++++++++++ + drivers/mfd/bcm2835-pm.c | 12 +- + drivers/soc/bcm/bcm2835-power.c | 6 +- + include/linux/mfd/bcm2835-pm.h | 2 +- + 6 files changed, 311 insertions(+), 10 deletions(-) + create mode 100644 drivers/char/broadcom/rpivid-mem.c + +--- a/drivers/char/broadcom/Kconfig ++++ b/drivers/char/broadcom/Kconfig +@@ -39,3 +39,11 @@ config BCM2835_SMI_DEV + This driver provides a character device interface (ioctl + read/write) to + Broadcom's Secondary Memory interface. The low-level functionality is provided + by the SMI driver itself. ++ ++config RPIVID_MEM ++ tristate "Character device driver for the Raspberry Pi RPIVid video decoder hardware" ++ default n ++ help ++ This driver provides a character device interface for memory-map operations ++ so userspace tools can access the control and status registers of the ++ Raspberry Pi RPiVid video decoder hardware. +--- a/drivers/char/broadcom/Makefile ++++ b/drivers/char/broadcom/Makefile +@@ -2,3 +2,4 @@ obj-$(CONFIG_BCM2708_VCMEM) += vc_mem.o + obj-$(CONFIG_BCM_VCIO) += vcio.o + obj-$(CONFIG_BCM2835_DEVGPIOMEM)+= bcm2835-gpiomem.o + obj-$(CONFIG_BCM2835_SMI_DEV) += bcm2835_smi_dev.o ++obj-$(CONFIG_RPIVID_MEM) += rpivid-mem.o +--- /dev/null ++++ b/drivers/char/broadcom/rpivid-mem.c +@@ -0,0 +1,292 @@ ++// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause ++/** ++ * rpivid-mem.c - character device access to the RPiVid decoder registers ++ * ++ * Based on bcm2835-gpiomem.c. Provides IO memory access to the decoder ++ * register blocks such that ffmpeg plugins can access the hardware. ++ * ++ * Jonathan Bell ++ * Copyright (c) 2019, Raspberry Pi (Trading) Ltd. ++ * ++ * Redistribution and use in source and binary forms, with or without ++ * modification, are permitted provided that the following conditions ++ * are met: ++ * 1. Redistributions of source code must retain the above copyright ++ * notice, this list of conditions, and the following disclaimer, ++ * without modification. ++ * 2. Redistributions in binary form must reproduce the above copyright ++ * notice, this list of conditions and the following disclaimer in the ++ * documentation and/or other materials provided with the distribution. ++ * 3. The names of the above-listed copyright holders may not be used ++ * to endorse or promote products derived from this software without ++ * specific prior written permission. ++ * ++ * ALTERNATIVELY, this software may be distributed under the terms of the ++ * GNU General Public License ("GPL") version 2, as published by the Free ++ * Software Foundation. ++ * ++ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS ++ * IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ++ * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR ++ * PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR ++ * CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, ++ * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, ++ * PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR ++ * PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF ++ * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING ++ * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS ++ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define DRIVER_NAME "rpivid-mem" ++#define DEVICE_MINOR 0 ++ ++struct rpivid_mem_priv { ++ dev_t devid; ++ struct class *class; ++ struct cdev rpivid_mem_cdev; ++ unsigned long regs_phys; ++ unsigned long mem_window_len; ++ struct device *dev; ++ const char *name; ++}; ++ ++static int rpivid_mem_open(struct inode *inode, struct file *file) ++{ ++ int dev = iminor(inode); ++ int ret = 0; ++ struct rpivid_mem_priv *priv; ++ ++ if (dev != DEVICE_MINOR && dev != DEVICE_MINOR + 1) ++ ret = -ENXIO; ++ ++ priv = container_of(inode->i_cdev, struct rpivid_mem_priv, ++ rpivid_mem_cdev); ++ if (!priv) ++ return -EINVAL; ++ file->private_data = priv; ++ return ret; ++} ++ ++static int rpivid_mem_release(struct inode *inode, struct file *file) ++{ ++ int dev = iminor(inode); ++ int ret = 0; ++ ++ if (dev != DEVICE_MINOR && dev != DEVICE_MINOR + 1) ++ ret = -ENXIO; ++ ++ return ret; ++} ++ ++static const struct vm_operations_struct rpivid_mem_vm_ops = { ++#ifdef CONFIG_HAVE_IOREMAP_PROT ++ .access = generic_access_phys ++#endif ++}; ++ ++static int rpivid_mem_mmap(struct file *file, struct vm_area_struct *vma) ++{ ++ struct rpivid_mem_priv *priv; ++ unsigned long pages; ++ ++ priv = file->private_data; ++ pages = priv->regs_phys >> PAGE_SHIFT; ++ /* ++ * The address decode is far larger than the actual number of registers. ++ * Just map the whole lot in. ++ */ ++ vma->vm_page_prot = phys_mem_access_prot(file, pages, ++ priv->mem_window_len, ++ vma->vm_page_prot); ++ vma->vm_ops = &rpivid_mem_vm_ops; ++ if (remap_pfn_range(vma, vma->vm_start, ++ pages, ++ priv->mem_window_len, ++ vma->vm_page_prot)) { ++ return -EAGAIN; ++ } ++ return 0; ++} ++ ++static const struct file_operations ++rpivid_mem_fops = { ++ .owner = THIS_MODULE, ++ .open = rpivid_mem_open, ++ .release = rpivid_mem_release, ++ .mmap = rpivid_mem_mmap, ++}; ++ ++static const struct of_device_id rpivid_mem_of_match[]; ++static int rpivid_mem_probe(struct platform_device *pdev) ++{ ++ int err; ++ const struct of_device_id *id; ++ struct device *dev = &pdev->dev; ++ struct resource *ioresource; ++ struct rpivid_mem_priv *priv; ++ ++ /* Allocate buffers and instance data */ ++ ++ priv = kzalloc(sizeof(struct rpivid_mem_priv), GFP_KERNEL); ++ ++ if (!priv) { ++ err = -ENOMEM; ++ goto failed_inst_alloc; ++ } ++ platform_set_drvdata(pdev, priv); ++ ++ priv->dev = dev; ++ id = of_match_device(rpivid_mem_of_match, dev); ++ if (!id) ++ return -EINVAL; ++ priv->name = id->data; ++ ++ ioresource = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ if (ioresource) { ++ priv->regs_phys = ioresource->start; ++ priv->mem_window_len = ioresource->end - ioresource->start; ++ } else { ++ dev_err(priv->dev, "failed to get IO resource"); ++ err = -ENOENT; ++ goto failed_get_resource; ++ } ++ ++ /* Create character device entries */ ++ ++ err = alloc_chrdev_region(&priv->devid, ++ DEVICE_MINOR, 2, priv->name); ++ if (err != 0) { ++ dev_err(priv->dev, "unable to allocate device number"); ++ goto failed_alloc_chrdev; ++ } ++ cdev_init(&priv->rpivid_mem_cdev, &rpivid_mem_fops); ++ priv->rpivid_mem_cdev.owner = THIS_MODULE; ++ err = cdev_add(&priv->rpivid_mem_cdev, priv->devid, 2); ++ if (err != 0) { ++ dev_err(priv->dev, "unable to register device"); ++ goto failed_cdev_add; ++ } ++ ++ /* Create sysfs entries */ ++ ++ priv->class = class_create(THIS_MODULE, priv->name); ++ if (IS_ERR(priv->class)) { ++ err = PTR_ERR(priv->class); ++ goto failed_class_create; ++ } ++ ++ dev = device_create(priv->class, NULL, priv->devid, NULL, priv->name); ++ if (IS_ERR(dev)) { ++ err = PTR_ERR(dev); ++ goto failed_device_create; ++ } ++ ++ /* Legacy alias */ ++ { ++ char *oldname = kstrdup(priv->name, GFP_KERNEL); ++ ++ oldname[1] = 'a'; ++ oldname[2] = 'r'; ++ oldname[3] = 'g'; ++ oldname[4] = 'o'; ++ oldname[5] = 'n'; ++ dev = device_create(priv->class, NULL, priv->devid + 1, NULL, ++ oldname + 1); ++ kfree(oldname); ++ ++ if (IS_ERR(dev)) { ++ err = PTR_ERR(dev); ++ goto failed_legacy_device_create; ++ } ++ } ++ ++ dev_info(priv->dev, "%s initialised: Registers at 0x%08lx length 0x%08lx", ++ priv->name, priv->regs_phys, priv->mem_window_len); ++ ++ return 0; ++ ++failed_legacy_device_create: ++ device_destroy(priv->class, priv->devid); ++failed_device_create: ++ class_destroy(priv->class); ++failed_class_create: ++ cdev_del(&priv->rpivid_mem_cdev); ++failed_cdev_add: ++ unregister_chrdev_region(priv->devid, 1); ++failed_alloc_chrdev: ++failed_get_resource: ++ kfree(priv); ++failed_inst_alloc: ++ dev_err(&pdev->dev, "could not load rpivid_mem"); ++ return err; ++} ++ ++static int rpivid_mem_remove(struct platform_device *pdev) ++{ ++ struct device *dev = &pdev->dev; ++ struct rpivid_mem_priv *priv = platform_get_drvdata(pdev); ++ ++ device_destroy(priv->class, priv->devid + 1); ++ device_destroy(priv->class, priv->devid); ++ class_destroy(priv->class); ++ cdev_del(&priv->rpivid_mem_cdev); ++ unregister_chrdev_region(priv->devid, 1); ++ kfree(priv); ++ ++ dev_info(dev, "%s driver removed - OK", priv->name); ++ return 0; ++} ++ ++static const struct of_device_id rpivid_mem_of_match[] = { ++ { ++ .compatible = "raspberrypi,rpivid-hevc-decoder", ++ .data = "rpivid-hevcmem", ++ }, ++ { ++ .compatible = "raspberrypi,rpivid-h264-decoder", ++ .data = "rpivid-h264mem", ++ }, ++ { ++ .compatible = "raspberrypi,rpivid-vp9-decoder", ++ .data = "rpivid-vp9mem", ++ }, ++ /* The "intc" is included as this block of hardware contains the ++ * "frame done" status flags. ++ */ ++ { ++ .compatible = "raspberrypi,rpivid-local-intc", ++ .data = "rpivid-intcmem", ++ }, ++ { /* sentinel */ }, ++}; ++ ++MODULE_DEVICE_TABLE(of, rpivid_mem_of_match); ++ ++static struct platform_driver rpivid_mem_driver = { ++ .probe = rpivid_mem_probe, ++ .remove = rpivid_mem_remove, ++ .driver = { ++ .name = DRIVER_NAME, ++ .owner = THIS_MODULE, ++ .of_match_table = rpivid_mem_of_match, ++ }, ++}; ++ ++module_platform_driver(rpivid_mem_driver); ++ ++MODULE_ALIAS("platform:rpivid-mem"); ++MODULE_LICENSE("GPL"); ++MODULE_DESCRIPTION("Driver for accessing RPiVid decoder registers from userspace"); ++MODULE_AUTHOR("Jonathan Bell "); +--- a/drivers/mfd/bcm2835-pm.c ++++ b/drivers/mfd/bcm2835-pm.c +@@ -50,14 +50,14 @@ static int bcm2835_pm_probe(struct platf + if (ret) + return ret; + +- /* Map the ARGON ASB regs if present. */ ++ /* Map the RPiVid ASB regs if present. */ + res = platform_get_resource(pdev, IORESOURCE_MEM, 2); + if (res) { +- pm->arg_asb = devm_ioremap_resource(dev, res); +- if (IS_ERR(pm->arg_asb)) { +- dev_err(dev, "Failed to map ARGON ASB: %ld\n", +- PTR_ERR(pm->arg_asb)); +- return PTR_ERR(pm->arg_asb); ++ pm->rpivid_asb = devm_ioremap_resource(dev, res); ++ if (IS_ERR(pm->rpivid_asb)) { ++ dev_err(dev, "Failed to map RPiVid ASB: %ld\n", ++ PTR_ERR(pm->rpivid_asb)); ++ return PTR_ERR(pm->rpivid_asb); + } + } + +--- a/drivers/soc/bcm/bcm2835-power.c ++++ b/drivers/soc/bcm/bcm2835-power.c +@@ -637,15 +637,15 @@ static int bcm2835_power_probe(struct pl + power->base = pm->base; + power->asb = pm->asb; + +- /* 2711 hack: the new ARGON ASB took over V3D, which is our ++ /* 2711 hack: the new RPiVid ASB took over V3D, which is our + * only consumer of this driver so far. The old ASB seems to + * still be present with ISP and H264 bits but no V3D, but I + * don't know if that's real or not. The V3D is in the same + * place in the new ASB as the old one, so just poke the new + * one for now. + */ +- if (pm->arg_asb) { +- power->asb = pm->arg_asb; ++ if (pm->rpivid_asb) { ++ power->asb = pm->rpivid_asb; + power->is_2711 = true; + } + +--- a/include/linux/mfd/bcm2835-pm.h ++++ b/include/linux/mfd/bcm2835-pm.h +@@ -9,7 +9,7 @@ struct bcm2835_pm { + struct device *dev; + void __iomem *base; + void __iomem *asb; +- void __iomem *arg_asb; ++ void __iomem *rpivid_asb; + }; + + #endif /* BCM2835_MFD_PM_H */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0151-hid-usb-Add-device-quirks-for-Freeway-Airmouse-T3-an.patch b/target/linux/bcm27xx/patches-5.10/950-0151-hid-usb-Add-device-quirks-for-Freeway-Airmouse-T3-an.patch new file mode 100644 index 0000000000..217b2117d4 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0151-hid-usb-Add-device-quirks-for-Freeway-Airmouse-T3-an.patch @@ -0,0 +1,63 @@ +From 25805001705a4b01edec63c6ec63482d16dce8d1 Mon Sep 17 00:00:00 2001 +From: Jonathan Bell +Date: Thu, 1 Aug 2019 16:41:20 +0100 +Subject: [PATCH] hid: usb: Add device quirks for Freeway Airmouse T3 + and MX3 + +These wireless mouse/keyboard combo remote control devices specify +multiple "wheel" events in their report descriptors. The wheel events +are incorrectly defined and apparently map to accelerometer data, leading +to spurious mouse scroll events being generated at an extreme rate when +the device is moved. + +As a workaround, use HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE to mask +feeding the extra wheel events to the input subsystem. + +See: https://github.com/raspberrypi/firmware/issues/1189 + +Signed-off-by: Jonathan Bell +--- + drivers/hid/hid-ids.h | 6 ++++++ + drivers/hid/hid-quirks.c | 2 ++ + 2 files changed, 8 insertions(+) + +--- a/drivers/hid/hid-ids.h ++++ b/drivers/hid/hid-ids.h +@@ -221,6 +221,9 @@ + #define USB_VENDOR_ID_BAANTO 0x2453 + #define USB_DEVICE_ID_BAANTO_MT_190W2 0x0100 + ++#define USB_VENDOR_ID_BEKEN 0x25a7 ++#define USB_DEVICE_ID_AIRMOUSE_T3 0x2402 ++ + #define USB_VENDOR_ID_BELKIN 0x050d + #define USB_DEVICE_ID_FLIP_KVM 0x3201 + +@@ -1268,6 +1271,9 @@ + #define USB_VENDOR_ID_XAT 0x2505 + #define USB_DEVICE_ID_XAT_CSR 0x0220 + ++#define USB_VENDOR_ID_XENTA 0x1d57 ++#define USB_DEVICE_ID_AIRMOUSE_MX3 0xad03 ++ + #define USB_VENDOR_ID_XIN_MO 0x16c0 + #define USB_DEVICE_ID_XIN_MO_DUAL_ARCADE 0x05e1 + #define USB_DEVICE_ID_THT_2P_ARCADE 0x75e1 +--- a/drivers/hid/hid-quirks.c ++++ b/drivers/hid/hid-quirks.c +@@ -41,6 +41,7 @@ static const struct hid_device_id hid_qu + { HID_USB_DEVICE(USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_CS682), HID_QUIRK_NOGET }, + { HID_USB_DEVICE(USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_CS692), HID_QUIRK_NOGET }, + { HID_USB_DEVICE(USB_VENDOR_ID_ATEN, USB_DEVICE_ID_ATEN_UC100KM), HID_QUIRK_NOGET }, ++ { HID_USB_DEVICE(USB_VENDOR_ID_BEKEN, USB_DEVICE_ID_AIRMOUSE_T3), HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE }, + { HID_USB_DEVICE(USB_VENDOR_ID_CHICONY, USB_DEVICE_ID_CHICONY_MULTI_TOUCH), HID_QUIRK_MULTI_INPUT }, + { HID_USB_DEVICE(USB_VENDOR_ID_CHICONY, USB_DEVICE_ID_CHICONY_PIXART_USB_OPTICAL_MOUSE), HID_QUIRK_ALWAYS_POLL }, + { HID_USB_DEVICE(USB_VENDOR_ID_CHICONY, USB_DEVICE_ID_CHICONY_PIXART_USB_OPTICAL_MOUSE2), HID_QUIRK_ALWAYS_POLL }, +@@ -193,6 +194,7 @@ static const struct hid_device_id hid_qu + { HID_USB_DEVICE(USB_VENDOR_ID_WISEGROUP, USB_DEVICE_ID_QUAD_USB_JOYPAD), HID_QUIRK_NOGET | HID_QUIRK_MULTI_INPUT }, + { HID_USB_DEVICE(USB_VENDOR_ID_XIN_MO, USB_DEVICE_ID_XIN_MO_DUAL_ARCADE), HID_QUIRK_MULTI_INPUT }, + { HID_USB_DEVICE(USB_VENDOR_ID_LOGITECH, USB_DEVICE_ID_LOGITECH_GROUP_AUDIO), HID_QUIRK_NOGET }, ++ { HID_USB_DEVICE(USB_VENDOR_ID_XENTA, USB_DEVICE_ID_AIRMOUSE_MX3), HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE }, + + { 0 } + }; diff --git a/target/linux/bcm27xx/patches-5.10/950-0152-Add-HDMI1-facility-to-the-driver.patch b/target/linux/bcm27xx/patches-5.10/950-0152-Add-HDMI1-facility-to-the-driver.patch new file mode 100644 index 0000000000..7a4a48aaed --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0152-Add-HDMI1-facility-to-the-driver.patch @@ -0,0 +1,85 @@ +From 3dbfcfbd3f9a0cae3bb426954ad5fd7d193507cc Mon Sep 17 00:00:00 2001 +From: James Hughes +Date: Tue, 16 Jul 2019 12:18:21 +0100 +Subject: [PATCH] Add HDMI1 facility to the driver. + +For generic ALSA, all you need is the bcm2835.h change, but +have also added structures for IEC958 HDMI. Not sure how to +test those. +--- + .../vc04_services/bcm2835-audio/bcm2835.c | 29 ++++++++++++++++--- + .../vc04_services/bcm2835-audio/bcm2835.h | 4 ++- + 2 files changed, 28 insertions(+), 5 deletions(-) + +--- a/drivers/staging/vc04_services/bcm2835-audio/bcm2835.c ++++ b/drivers/staging/vc04_services/bcm2835-audio/bcm2835.c +@@ -79,7 +79,11 @@ static int bcm2835_audio_alsa_newpcm(str + if (err) + return err; + +- err = snd_bcm2835_new_pcm(chip, "bcm2835 IEC958/HDMI", 1, 0, 1, true); ++ err = snd_bcm2835_new_pcm(chip, "bcm2835 IEC958/HDMI", 1, AUDIO_DEST_HDMI0, 1, true); ++ if (err) ++ return err; ++ ++ err = snd_bcm2835_new_pcm(chip, "bcm2835 IEC958/HDMI1", 2, AUDIO_DEST_HDMI1, 1, true); + if (err) + return err; + +@@ -106,7 +110,7 @@ static struct bcm2835_audio_driver bcm28 + .newctl = snd_bcm2835_new_ctl, + }; + +-static struct bcm2835_audio_driver bcm2835_audio_hdmi = { ++static struct bcm2835_audio_driver bcm2835_audio_hdmi0 = { + .driver = { + .name = "bcm2835_hdmi", + .owner = THIS_MODULE, +@@ -116,7 +120,20 @@ static struct bcm2835_audio_driver bcm28 + .minchannels = 1, + .newpcm = bcm2835_audio_simple_newpcm, + .newctl = snd_bcm2835_new_hdmi_ctl, +- .route = AUDIO_DEST_HDMI ++ .route = AUDIO_DEST_HDMI0 ++}; ++ ++static struct bcm2835_audio_driver bcm2835_audio_hdmi1 = { ++ .driver = { ++ .name = "bcm2835_hdmi", ++ .owner = THIS_MODULE, ++ }, ++ .shortname = "bcm2835 HDMI 1", ++ .longname = "bcm2835 HDMI 1", ++ .minchannels = 1, ++ .newpcm = bcm2835_audio_simple_newpcm, ++ .newctl = snd_bcm2835_new_hdmi_ctl, ++ .route = AUDIO_DEST_HDMI1 + }; + + static struct bcm2835_audio_driver bcm2835_audio_headphones = { +@@ -143,7 +160,11 @@ static struct bcm2835_audio_drivers chil + .is_enabled = &enable_compat_alsa, + }, + { +- .audio_driver = &bcm2835_audio_hdmi, ++ .audio_driver = &bcm2835_audio_hdmi0, ++ .is_enabled = &enable_hdmi, ++ }, ++ { ++ .audio_driver = &bcm2835_audio_hdmi1, + .is_enabled = &enable_hdmi, + }, + { +--- a/drivers/staging/vc04_services/bcm2835-audio/bcm2835.h ++++ b/drivers/staging/vc04_services/bcm2835-audio/bcm2835.h +@@ -33,7 +33,9 @@ enum { + enum snd_bcm2835_route { + AUDIO_DEST_AUTO = 0, + AUDIO_DEST_HEADPHONES = 1, +- AUDIO_DEST_HDMI = 2, ++ AUDIO_DEST_HDMI = 2, // for backwards compatibility. ++ AUDIO_DEST_HDMI0 = 2, ++ AUDIO_DEST_HDMI1 = 3, + AUDIO_DEST_MAX, + }; + diff --git a/target/linux/bcm27xx/patches-5.10/950-0153-net-bcmgenet-Workaround-2-for-Pi4-Ethernet-fail.patch b/target/linux/bcm27xx/patches-5.10/950-0153-net-bcmgenet-Workaround-2-for-Pi4-Ethernet-fail.patch new file mode 100644 index 0000000000..5f446dcc2f --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0153-net-bcmgenet-Workaround-2-for-Pi4-Ethernet-fail.patch @@ -0,0 +1,51 @@ +From 5d5a886b8ae7d18e6aeb44acd37fc4bd23ca1952 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 9 Aug 2019 08:51:43 +0100 +Subject: [PATCH] net: bcmgenet: Workaround #2 for Pi4 Ethernet fail + +Some combinations of Pi 4Bs and Ethernet switches don't reliably get a +DCHP-assigned IP address, leaving the unit with a self=assigned 169.254 +address. In the failure case, the Pi is left able to receive packets +but not send them, suggesting that the MAC<->PHY link is getting into +a bad state. + +It has been found empirically that skipping a reset step by the genet +driver prevents the failures. No downsides have been discovered yet, +and unlike the forced renegotiation it doesn't increase the time to +get an IP address, so the workaround is enabled by default; add + + genet.skip_umac_reset=n + +to the command line to disable it. + +See: https://github.com/raspberrypi/linux/issues/3108 + +Signed-off-by: Phil Elwell +--- + drivers/net/ethernet/broadcom/genet/bcmgenet.c | 8 ++++++++ + 1 file changed, 8 insertions(+) + +--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c ++++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c +@@ -67,6 +67,9 @@ + + /* Forward declarations */ + static void bcmgenet_set_rx_mode(struct net_device *dev); ++static bool skip_umac_reset = true; ++module_param(skip_umac_reset, bool, 0444); ++MODULE_PARM_DESC(skip_umac_reset, "Skip UMAC reset step"); + + static inline void bcmgenet_writel(u32 value, void __iomem *offset) + { +@@ -2426,6 +2429,11 @@ static void reset_umac(struct bcmgenet_p + bcmgenet_rbuf_ctrl_set(priv, 0); + udelay(10); + ++ if (skip_umac_reset) { ++ pr_warn("Skipping UMAC reset\n"); ++ return; ++ } ++ + /* issue soft reset and disable MAC while updating its registers */ + bcmgenet_umac_writel(priv, CMD_SW_RESET, UMAC_CMD); + udelay(2); diff --git a/target/linux/bcm27xx/patches-5.10/950-0154-xhci-Use-more-event-ring-segment-table-entries.patch b/target/linux/bcm27xx/patches-5.10/950-0154-xhci-Use-more-event-ring-segment-table-entries.patch new file mode 100644 index 0000000000..b80544a16b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0154-xhci-Use-more-event-ring-segment-table-entries.patch @@ -0,0 +1,60 @@ +From 56212428792d53e5d2c741733d5f284331e84c97 Mon Sep 17 00:00:00 2001 +From: Jonathan Bell +Date: Tue, 13 Aug 2019 15:53:29 +0100 +Subject: [PATCH] xhci: Use more event ring segment table entries + +Users have reported log spam created by "Event Ring Full" xHC event +TRBs. These are caused by interrupt latency in conjunction with a very +busy set of devices on the bus. The errors are benign, but throughput +will suffer as the xHC will pause processing of transfers until the +event ring is drained by the kernel. Expand the number of event TRB slots +available by increasing the number of event ring segments in the ERST. + +Controllers have a hardware-defined limit as to the number of ERST +entries they can process, so make the actual number in use +min(ERST_MAX_SEGS, hw_max). + +Signed-off-by: Jonathan Bell +--- + drivers/usb/host/xhci-mem.c | 8 +++++--- + drivers/usb/host/xhci.h | 4 ++-- + 2 files changed, 7 insertions(+), 5 deletions(-) + +--- a/drivers/usb/host/xhci-mem.c ++++ b/drivers/usb/host/xhci-mem.c +@@ -2525,9 +2525,11 @@ int xhci_mem_init(struct xhci_hcd *xhci, + * Event ring setup: Allocate a normal ring, but also setup + * the event ring segment table (ERST). Section 4.9.3. + */ ++ val2 = 1 << HCS_ERST_MAX(xhci->hcs_params2); ++ val2 = min_t(unsigned int, ERST_MAX_SEGS, val2); + xhci_dbg_trace(xhci, trace_xhci_dbg_init, "// Allocating event ring"); +- xhci->event_ring = xhci_ring_alloc(xhci, ERST_NUM_SEGS, 1, TYPE_EVENT, +- 0, flags); ++ xhci->event_ring = xhci_ring_alloc(xhci, val2, 1, TYPE_EVENT, ++ 0, flags); + if (!xhci->event_ring) + goto fail; + if (xhci_check_trb_in_td_math(xhci) < 0) +@@ -2540,7 +2542,7 @@ int xhci_mem_init(struct xhci_hcd *xhci, + /* set ERST count with the number of entries in the segment table */ + val = readl(&xhci->ir_set->erst_size); + val &= ERST_SIZE_MASK; +- val |= ERST_NUM_SEGS; ++ val |= val2; + xhci_dbg_trace(xhci, trace_xhci_dbg_init, + "// Write ERST size = %i to ir_set 0 (some bits preserved)", + val); +--- a/drivers/usb/host/xhci.h ++++ b/drivers/usb/host/xhci.h +@@ -1650,8 +1650,8 @@ struct urb_priv { + * Each segment table entry is 4*32bits long. 1K seems like an ok size: + * (1K bytes * 8bytes/bit) / (4*32 bits) = 64 segment entries in the table, + * meaning 64 ring segments. +- * Initial allocated size of the ERST, in number of entries */ +-#define ERST_NUM_SEGS 1 ++ * Maximum number of segments in the ERST */ ++#define ERST_MAX_SEGS 8 + /* Initial allocated size of the ERST, in number of entries */ + #define ERST_SIZE 64 + /* Initial number of event segment rings allocated */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0155-configs-arm64-bcm2711-Enable-V3D.patch b/target/linux/bcm27xx/patches-5.10/950-0155-configs-arm64-bcm2711-Enable-V3D.patch new file mode 100644 index 0000000000..002602b8c1 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0155-configs-arm64-bcm2711-Enable-V3D.patch @@ -0,0 +1,28 @@ +From d724240a2db99f47c3eb8330960b14a2719ed7cd Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 15 Aug 2019 12:02:34 +0100 +Subject: [PATCH] configs: arm64/bcm2711: Enable V3D + +Enable the V3D driver, which depends on BCM2835_POWER. + +Originally submitted by GitHub user 'phire' in a slightly different +form. + +See: https://github.com/raspberrypi/linux/pull/3063 + +Signed-off-by: Phil Elwell +--- + drivers/gpu/drm/v3d/Kconfig | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/gpu/drm/v3d/Kconfig ++++ b/drivers/gpu/drm/v3d/Kconfig +@@ -1,7 +1,7 @@ + # SPDX-License-Identifier: GPL-2.0-only + config DRM_V3D + tristate "Broadcom V3D 3.x and newer" +- depends on ARCH_BCM || ARCH_BCMSTB || COMPILE_TEST ++ depends on ARCH_BCM || ARCH_BCMSTB || ARCH_BCM2835 || COMPILE_TEST + depends on DRM + depends on COMMON_CLK + depends on MMU diff --git a/target/linux/bcm27xx/patches-5.10/950-0156-arch-arm-Add-model-string-to-cpuinfo.patch b/target/linux/bcm27xx/patches-5.10/950-0156-arch-arm-Add-model-string-to-cpuinfo.patch new file mode 100644 index 0000000000..8624ad929c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0156-arch-arm-Add-model-string-to-cpuinfo.patch @@ -0,0 +1,36 @@ +From 5f7b32d4608113927128391620cd80048db52a2e Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 3 Sep 2019 18:16:56 +0100 +Subject: [PATCH] arch/arm: Add model string to cpuinfo + +Signed-off-by: Phil Elwell +--- + arch/arm/kernel/setup.c | 10 ++++++++++ + 1 file changed, 10 insertions(+) + +--- a/arch/arm/kernel/setup.c ++++ b/arch/arm/kernel/setup.c +@@ -1255,6 +1255,8 @@ static int c_show(struct seq_file *m, vo + { + int i, j; + u32 cpuid; ++ struct device_node *np; ++ const char *model; + + for_each_online_cpu(i) { + /* +@@ -1314,6 +1316,14 @@ static int c_show(struct seq_file *m, vo + seq_printf(m, "Revision\t: %04x\n", system_rev); + seq_printf(m, "Serial\t\t: %s\n", system_serial); + ++ np = of_find_node_by_path("/"); ++ if (np) { ++ if (!of_property_read_string(np, "model", ++ &model)) ++ seq_printf(m, "Model\t\t: %s\n", model); ++ of_node_put(np); ++ } ++ + return 0; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0157-arch-arm64-Add-Revision-Serial-Model-to-cpuinfo.patch b/target/linux/bcm27xx/patches-5.10/950-0157-arch-arm64-Add-Revision-Serial-Model-to-cpuinfo.patch new file mode 100644 index 0000000000..5d2cd9691a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0157-arch-arm64-Add-Revision-Serial-Model-to-cpuinfo.patch @@ -0,0 +1,58 @@ +From 24f0d858fbabe69c32829edc0e2765b1fa5cc8ec Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 3 Sep 2019 18:17:25 +0100 +Subject: [PATCH] arch/arm64: Add Revision, Serial, Model to cpuinfo + +Signed-off-by: Phil Elwell +--- + arch/arm64/kernel/cpuinfo.c | 25 +++++++++++++++++++++++++ + 1 file changed, 25 insertions(+) + +--- a/arch/arm64/kernel/cpuinfo.c ++++ b/arch/arm64/kernel/cpuinfo.c +@@ -17,6 +17,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -137,6 +138,10 @@ static int c_show(struct seq_file *m, vo + { + int i, j; + bool compat = personality(current->personality) == PER_LINUX32; ++ struct device_node *np; ++ const char *model; ++ const char *serial; ++ u32 revision; + + for_each_online_cpu(i) { + struct cpuinfo_arm64 *cpuinfo = &per_cpu(cpu_data, i); +@@ -197,6 +202,26 @@ static int c_show(struct seq_file *m, vo + seq_printf(m, "CPU revision\t: %d\n\n", MIDR_REVISION(midr)); + } + ++ seq_printf(m, "Hardware\t: BCM2835\n"); ++ ++ np = of_find_node_by_path("/system"); ++ if (np) { ++ if (!of_property_read_u32(np, "linux,revision", &revision)) ++ seq_printf(m, "Revision\t: %04x\n", revision); ++ of_node_put(np); ++ } ++ ++ np = of_find_node_by_path("/"); ++ if (np) { ++ if (!of_property_read_string(np, "serial-number", ++ &serial)) ++ seq_printf(m, "Serial\t\t: %s\n", serial); ++ if (!of_property_read_string(np, "model", ++ &model)) ++ seq_printf(m, "Model\t\t: %s\n", model); ++ of_node_put(np); ++ } ++ + return 0; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0158-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch b/target/linux/bcm27xx/patches-5.10/950-0158-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch new file mode 100644 index 0000000000..b957f8f3f9 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0158-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch @@ -0,0 +1,77 @@ +From 4e4be52826939d4baa054e0c859fffd5c9ee7cd6 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 28 Aug 2019 13:34:30 +0100 +Subject: [PATCH] media: dt-bindings: Add binding for the Sony IMX219 + sensor + +The IMX219 is an 8MPix CSI2 sensor, supporting 2 or 4 data lanes. +Document the binding for this device. + +Signed-off-by: Dave Stevenson +--- + .../devicetree/bindings/media/i2c/imx219.txt | 59 +++++++++++++++++++ + 1 file changed, 59 insertions(+) + create mode 100644 Documentation/devicetree/bindings/media/i2c/imx219.txt + +--- /dev/null ++++ b/Documentation/devicetree/bindings/media/i2c/imx219.txt +@@ -0,0 +1,59 @@ ++* Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor ++ ++The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor with ++an active array size of 3280H x 2464V. It is programmable through I2C ++interface. The I2C address is fixed to 0x10 as per sensor data sheet. ++Image data is sent through MIPI CSI-2, which is configured as either 2 or 4 ++data lanes. ++ ++Required Properties: ++- compatible: value should be "sony,imx219" for imx219 sensor ++- reg: I2C bus address of the device ++- clocks: reference to the xclk input clock. ++- clock-names: should be "xclk". ++- DOVDD-supply: Digital I/O voltage supply, 1.8 volts ++- AVDD-supply: Analog voltage supply, 2.8 volts ++- DVDD-supply: Digital core voltage supply, 1.2 volts ++ ++Optional Properties: ++- xclr-gpios: reference to the GPIO connected to the xclr pin, if any. Must be ++ released after all supplies are applied. ++ This is an active high signal to the imx219. ++ ++The imx219 device node should contain one 'port' child node with ++an 'endpoint' subnode. For further reading on port node refer to ++Documentation/devicetree/bindings/media/video-interfaces.txt. ++ ++Endpoint node required properties for CSI-2 connection are: ++- remote-endpoint: a phandle to the bus receiver's endpoint node. ++- clock-lanes: should be set to <0> (clock lane on hardware lane 0) ++- data-lanes: should be set to <1 2>, or <1 2 3 4> (two or four lane CSI-2 ++ supported) ++ ++Example: ++ sensor@10 { ++ compatible = "sony,imx219"; ++ reg = <0x10>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ clocks = <&imx219_clk>; ++ clock-names = "xclk"; ++ xclr-gpios = <&gpio_sensor 0 0>; ++ DOVDD-supply = <&vgen4_reg>; /* 1.8v */ ++ AVDD-supply = <&vgen3_reg>; /* 2.8v */ ++ DVDD-supply = <&vgen2_reg>; /* 1.2v */ ++ ++ imx219_clk: camera-clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <24000000>; ++ }; ++ ++ port { ++ sensor_out: endpoint { ++ remote-endpoint = <&csiss_in>; ++ clock-lanes = <0>; ++ data-lanes = <1 2>; ++ }; ++ }; ++ }; diff --git a/target/linux/bcm27xx/patches-5.10/950-0159-v4l2-Add-a-Greyworld-AWB-mode.patch b/target/linux/bcm27xx/patches-5.10/950-0159-v4l2-Add-a-Greyworld-AWB-mode.patch new file mode 100644 index 0000000000..5755cde42c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0159-v4l2-Add-a-Greyworld-AWB-mode.patch @@ -0,0 +1,34 @@ +From 1c6c1ab42e61cdca555c85bdde5677b13b5cd5f3 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Fri, 6 Sep 2019 15:04:51 +0100 +Subject: [PATCH] v4l2: Add a Greyworld AWB mode. + +Adds a simple greyworld white balance preset, mainly for use +with cameras without an IR filter (eg Raspberry Pi NoIR) + +Signed-off-by: Dave Stevenson +--- + drivers/media/v4l2-core/v4l2-ctrls.c | 1 + + include/uapi/linux/v4l2-controls.h | 1 + + 2 files changed, 2 insertions(+) + +--- a/drivers/media/v4l2-core/v4l2-ctrls.c ++++ b/drivers/media/v4l2-core/v4l2-ctrls.c +@@ -275,6 +275,7 @@ const char * const *v4l2_ctrl_get_menu(u + "Flash", + "Cloudy", + "Shade", ++ "Greyworld", + NULL, + }; + static const char * const camera_iso_sensitivity_auto[] = { +--- a/include/uapi/linux/v4l2-controls.h ++++ b/include/uapi/linux/v4l2-controls.h +@@ -886,6 +886,7 @@ enum v4l2_auto_n_preset_white_balance { + V4L2_WHITE_BALANCE_FLASH = 7, + V4L2_WHITE_BALANCE_CLOUDY = 8, + V4L2_WHITE_BALANCE_SHADE = 9, ++ V4L2_WHITE_BALANCE_GREYWORLD = 10, + }; + + #define V4L2_CID_WIDE_DYNAMIC_RANGE (V4L2_CID_CAMERA_CLASS_BASE+21) diff --git a/target/linux/bcm27xx/patches-5.10/950-0160-staging-bcm2835-camera-Add-greyworld-AWB-mode.patch b/target/linux/bcm27xx/patches-5.10/950-0160-staging-bcm2835-camera-Add-greyworld-AWB-mode.patch new file mode 100644 index 0000000000..cbbe6727cd --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0160-staging-bcm2835-camera-Add-greyworld-AWB-mode.patch @@ -0,0 +1,37 @@ +From 827f9e8f76bd2674835026e37aba31b3c3a784e4 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Fri, 6 Sep 2019 15:13:06 +0100 +Subject: [PATCH] staging: bcm2835-camera: Add greyworld AWB mode + +This is mainly used for the NoIR camera which has no IR +filter and can completely confuse normal AWB presets. + +Signed-off-by: Dave Stevenson +--- + drivers/staging/vc04_services/bcm2835-camera/controls.c | 4 ++++ + drivers/staging/vc04_services/vchiq-mmal/mmal-parameters.h | 1 + + 2 files changed, 5 insertions(+) + +--- a/drivers/staging/vc04_services/bcm2835-camera/controls.c ++++ b/drivers/staging/vc04_services/bcm2835-camera/controls.c +@@ -474,6 +474,10 @@ static int ctrl_set_awb_mode(struct bm28 + case V4L2_WHITE_BALANCE_SHADE: + u32_value = MMAL_PARAM_AWBMODE_SHADE; + break; ++ ++ case V4L2_WHITE_BALANCE_GREYWORLD: ++ u32_value = MMAL_PARAM_AWBMODE_GREYWORLD; ++ break; + } + + return vchiq_mmal_port_parameter_set(dev->instance, control, +--- a/drivers/staging/vc04_services/vchiq-mmal/mmal-parameters.h ++++ b/drivers/staging/vc04_services/vchiq-mmal/mmal-parameters.h +@@ -313,6 +313,7 @@ enum mmal_parameter_awbmode { + MMAL_PARAM_AWBMODE_INCANDESCENT, + MMAL_PARAM_AWBMODE_FLASH, + MMAL_PARAM_AWBMODE_HORIZON, ++ MMAL_PARAM_AWBMODE_GREYWORLD, + }; + + enum mmal_parameter_imagefx { diff --git a/target/linux/bcm27xx/patches-5.10/950-0161-drm-v3d-Delete-pm_runtime-support.patch b/target/linux/bcm27xx/patches-5.10/950-0161-drm-v3d-Delete-pm_runtime-support.patch new file mode 100644 index 0000000000..f6fdee0f48 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0161-drm-v3d-Delete-pm_runtime-support.patch @@ -0,0 +1,62 @@ +From 194db68e9c6c18c536714859e788de36a146dabb Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 18 Sep 2019 17:22:36 +0100 +Subject: [PATCH] drm/v3d: Delete pm_runtime support + +The pm_runtime was blocking changelist submission, so delete it as a +temporary workaround. + +Signed-off-by: Phil Elwell +--- + drivers/gpu/drm/v3d/v3d_gem.c | 5 ----- + drivers/gpu/drm/v3d/v3d_mmu.c | 11 ----------- + 2 files changed, 16 deletions(-) + +--- a/drivers/gpu/drm/v3d/v3d_gem.c ++++ b/drivers/gpu/drm/v3d/v3d_gem.c +@@ -478,10 +478,6 @@ v3d_job_init(struct v3d_dev *v3d, struct + job->v3d = v3d; + job->free = free; + +- ret = pm_runtime_get_sync(v3d->drm.dev); +- if (ret < 0) +- return ret; +- + xa_init_flags(&job->deps, XA_FLAGS_ALLOC); + + ret = drm_syncobj_find_fence(file_priv, in_sync, 0, 0, &in_fence); +@@ -498,7 +494,6 @@ v3d_job_init(struct v3d_dev *v3d, struct + return 0; + fail: + xa_destroy(&job->deps); +- pm_runtime_put_autosuspend(v3d->drm.dev); + return ret; + } + +--- a/drivers/gpu/drm/v3d/v3d_mmu.c ++++ b/drivers/gpu/drm/v3d/v3d_mmu.c +@@ -36,14 +36,6 @@ static int v3d_mmu_flush_all(struct v3d_ + { + int ret; + +- /* Keep power on the device on until we're done with this +- * call, but skip the flush if the device is off and will be +- * reset when powered back on. +- */ +- ret = pm_runtime_get_if_in_use(v3d->dev); +- if (ret == 0) +- return 0; +- + /* Make sure that another flush isn't already running when we + * start this one. + */ +@@ -71,9 +63,6 @@ static int v3d_mmu_flush_all(struct v3d_ + if (ret) + dev_err(v3d->drm.dev, "MMUC flush wait idle failed\n"); + +- pm_runtime_mark_last_busy(v3d->dev); +- pm_runtime_put_autosuspend(v3d->dev); +- + return ret; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0162-kbuild-Allow-.dtbo-overlays-to-be-built-piecemeal.patch b/target/linux/bcm27xx/patches-5.10/950-0162-kbuild-Allow-.dtbo-overlays-to-be-built-piecemeal.patch new file mode 100644 index 0000000000..c3be3d58e6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0162-kbuild-Allow-.dtbo-overlays-to-be-built-piecemeal.patch @@ -0,0 +1,36 @@ +From 39e3ab3e857a617b982dbeee2037f13edc46f799 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 23 Sep 2019 09:26:41 +0100 +Subject: [PATCH] kbuild: Allow .dtbo overlays to be built piecemeal + +Before 4.20, it was possible to build an arbitrary overlay by copying +it to arm/boot/dts/overlays/mytest-overlay.dts and running: + + make ARCH=arm overlays/mytest.dtbo + +In 4.20 the .dtb build rules were centralised, requiring the dowstream +.dtbo build rules to be changed. They were, enough to support "make ... +dtbs", but not sufficiently to allow this ad-hoc, one-off building of +individual files. + +Add the missing makefile rule to support this way of building. + +See: https://github.com/raspberrypi/linux/issues/3250 + +Signed-off-by: Phil Elwell +--- + Makefile | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/Makefile ++++ b/Makefile +@@ -1354,6 +1354,9 @@ ifneq ($(dtstree),) + %.dtb: include/config/kernel.release scripts_dtc + $(Q)$(MAKE) $(build)=$(dtstree) $(dtstree)/$@ + ++%.dtbo: prepare3 scripts_dtc ++ $(Q)$(MAKE) $(build)=$(dtstree) $(dtstree)/$@ ++ + PHONY += dtbs dtbs_install dtbs_check + dtbs: include/config/kernel.release scripts_dtc + $(Q)$(MAKE) $(build)=$(dtstree) diff --git a/target/linux/bcm27xx/patches-5.10/950-0163-ARM-bcm-Switch-board-clk-and-pinctrl-to-bcm2711-comp.patch b/target/linux/bcm27xx/patches-5.10/950-0163-ARM-bcm-Switch-board-clk-and-pinctrl-to-bcm2711-comp.patch new file mode 100644 index 0000000000..30f0455942 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0163-ARM-bcm-Switch-board-clk-and-pinctrl-to-bcm2711-comp.patch @@ -0,0 +1,26 @@ +From 676c69523fd366c0dfac97d2c343f565b563f62d Mon Sep 17 00:00:00 2001 +From: Stefan Wahren +Date: Thu, 19 Sep 2019 20:45:30 +0200 +Subject: [PATCH] ARM: bcm: Switch board, clk and pinctrl to bcm2711 + compatible + +After the decision to use bcm2711 compatible for upstream, we should +switch all accepted compatibles to bcm2711. So we can boot with +one DTB the down- and the upstream kernel. + +Signed-off-by: Stefan Wahren +--- + arch/arm/mach-bcm/board_bcm2835.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/arch/arm/mach-bcm/board_bcm2835.c ++++ b/arch/arm/mach-bcm/board_bcm2835.c +@@ -109,7 +109,7 @@ static const char * const bcm2835_compat + #ifdef CONFIG_ARCH_MULTI_V7 + "brcm,bcm2836", + "brcm,bcm2837", +- "brcm,bcm2838", ++ "brcm,bcm2711", + #endif + NULL + }; diff --git a/target/linux/bcm27xx/patches-5.10/950-0164-Rename-HDMI-ALSA-device-names-check-for-enable-state.patch b/target/linux/bcm27xx/patches-5.10/950-0164-Rename-HDMI-ALSA-device-names-check-for-enable-state.patch new file mode 100644 index 0000000000..3feaba9482 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0164-Rename-HDMI-ALSA-device-names-check-for-enable-state.patch @@ -0,0 +1,139 @@ +From 8f1af3614dd55e3c725b7f28f68ee6404e5f2e1a Mon Sep 17 00:00:00 2001 +From: James Hughes +Date: Tue, 24 Sep 2019 18:26:55 +0100 +Subject: [PATCH] Rename HDMI ALSA device names, check for enable state + +HDMI Alsa devices renamed to match names used by DRM, to +HDMI 1 and HDMI 2 + +Check for which HDMI devices are connected and only create +devices for those that are present. + +The rename of the devices might cause some backwards compatibility +issues, but since this particular part of the driver needs to be +specifically enabled, I suspect the number of people who will see +the problem will be very small. + +Signed-off-by: James Hughes +--- + .../vc04_services/bcm2835-audio/bcm2835.c | 70 +++++++++++++++++-- + 1 file changed, 63 insertions(+), 7 deletions(-) + +--- a/drivers/staging/vc04_services/bcm2835-audio/bcm2835.c ++++ b/drivers/staging/vc04_services/bcm2835-audio/bcm2835.c +@@ -9,8 +9,9 @@ + #include + + #include "bcm2835.h" ++#include + +-static bool enable_hdmi; ++static bool enable_hdmi, enable_hdmi0, enable_hdmi1; + static bool enable_headphones; + static bool enable_compat_alsa = true; + +@@ -115,8 +116,8 @@ static struct bcm2835_audio_driver bcm28 + .name = "bcm2835_hdmi", + .owner = THIS_MODULE, + }, +- .shortname = "bcm2835 HDMI", +- .longname = "bcm2835 HDMI", ++ .shortname = "bcm2835 HDMI 1", ++ .longname = "bcm2835 HDMI 1", + .minchannels = 1, + .newpcm = bcm2835_audio_simple_newpcm, + .newctl = snd_bcm2835_new_hdmi_ctl, +@@ -128,8 +129,8 @@ static struct bcm2835_audio_driver bcm28 + .name = "bcm2835_hdmi", + .owner = THIS_MODULE, + }, +- .shortname = "bcm2835 HDMI 1", +- .longname = "bcm2835 HDMI 1", ++ .shortname = "bcm2835 HDMI 2", ++ .longname = "bcm2835 HDMI 2", + .minchannels = 1, + .newpcm = bcm2835_audio_simple_newpcm, + .newctl = snd_bcm2835_new_hdmi_ctl, +@@ -161,11 +162,11 @@ static struct bcm2835_audio_drivers chil + }, + { + .audio_driver = &bcm2835_audio_hdmi0, +- .is_enabled = &enable_hdmi, ++ .is_enabled = &enable_hdmi0, + }, + { + .audio_driver = &bcm2835_audio_hdmi1, +- .is_enabled = &enable_hdmi, ++ .is_enabled = &enable_hdmi1, + }, + { + .audio_driver = &bcm2835_audio_headphones, +@@ -312,6 +313,53 @@ static int snd_add_child_devices(struct + return 0; + } + ++static void set_hdmi_enables(struct device *dev) ++{ ++ struct device_node *firmware_node; ++ struct rpi_firmware *firmware; ++ u32 num_displays, i, display_id; ++ int ret; ++ ++ firmware_node = of_parse_phandle(dev->of_node, "brcm,firmware", 0); ++ firmware = rpi_firmware_get(firmware_node); ++ ++ if (!firmware) ++ return; ++ ++ of_node_put(firmware_node); ++ ++ ret = rpi_firmware_property(firmware, ++ RPI_FIRMWARE_FRAMEBUFFER_GET_NUM_DISPLAYS, ++ &num_displays, sizeof(u32)); ++ ++ if (ret) ++ return; ++ ++ for (i = 0; i < num_displays; i++) { ++ display_id = i; ++ ret = rpi_firmware_property(firmware, ++ RPI_FIRMWARE_FRAMEBUFFER_GET_DISPLAY_ID, ++ &display_id, sizeof(display_id)); ++ if (!ret) { ++ if (display_id == 2) ++ enable_hdmi0 = true; ++ if (display_id == 7) ++ enable_hdmi1 = true; ++ } ++ } ++ ++ if (!enable_hdmi0 && enable_hdmi1) { ++ /* Swap them over and reassign route. This means ++ * that if we only have one connected, it is always named ++ * HDMI1, irrespective of if its on port HDMI0 or HDMI1. ++ * This should match with the naming of HDMI ports in DRM ++ */ ++ enable_hdmi0 = true; ++ enable_hdmi1 = false; ++ bcm2835_audio_hdmi0.route = AUDIO_DEST_HDMI1; ++ } ++} ++ + static int snd_bcm2835_alsa_probe(struct platform_device *pdev) + { + struct device *dev = &pdev->dev; +@@ -332,6 +380,14 @@ static int snd_bcm2835_alsa_probe(struct + numchans); + } + ++ if (!enable_compat_alsa) { ++ set_hdmi_enables(dev); ++ // In this mode, always enable analog output ++ enable_headphones = true; ++ } else { ++ enable_hdmi0 = enable_hdmi; ++ } ++ + err = bcm2835_devm_add_vchi_ctx(dev); + if (err) + return err; diff --git a/target/linux/bcm27xx/patches-5.10/950-0165-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch b/target/linux/bcm27xx/patches-5.10/950-0165-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch new file mode 100644 index 0000000000..ae1a0e256c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0165-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch @@ -0,0 +1,66 @@ +From effbf244f11642594a739755285cd16591831b13 Mon Sep 17 00:00:00 2001 +From: Markus Proeller +Date: Thu, 10 Oct 2019 19:12:08 +0200 +Subject: [PATCH] dt-bindings: Add binding for the Infineon IRS1125 + sensor + +Adds a binding for the Infineon IRS1125 time-of-flight depth +sensor. + +Signed-off-by: Markus Proeller +--- + .../devicetree/bindings/media/i2c/irs1125.txt | 48 +++++++++++++++++++ + 1 file changed, 48 insertions(+) + create mode 100644 Documentation/devicetree/bindings/media/i2c/irs1125.txt + +--- /dev/null ++++ b/Documentation/devicetree/bindings/media/i2c/irs1125.txt +@@ -0,0 +1,48 @@ ++* Infineon irs1125 time of flight sensor ++ ++The Infineon irs1125 is a time of flight digital image sensor with ++an active array size of 352H x 286V. It is programmable through I2C ++interface. The I2C address defaults to 0x3D, but can be reconfigured ++to address 0x3C or 0x41 via I2C commands. Image data is sent through ++MIPI CSI-2, which is configured as either 1 or 2 data lanes. ++ ++Required Properties: ++- compatible: value should be "infineon,irs1125" for irs1125 sensor ++- reg: I2C bus address of the device ++- clocks: reference to the xclk input clock. ++- pwdn-gpios: reference to the GPIO connected to the reset pin. ++ This is an active low signal to the iirs1125. ++ ++The irs1125 device node should contain one 'port' child node with ++an 'endpoint' subnode. For further reading on port node refer to ++Documentation/devicetree/bindings/media/video-interfaces.txt. ++ ++Endpoint node required properties for CSI-2 connection are: ++- remote-endpoint: a phandle to the bus receiver's endpoint node. ++- clock-lanes: should be set to <0> (clock lane on hardware lane 0) ++- data-lanes: should be set to <1> or <1 2> (one or two lane CSI-2 ++ supported) ++ ++Example: ++ sensor@10 { ++ compatible = "infineon,irs1125"; ++ reg = <0x3D>; ++ #address-cells = <1>; ++ #size-cells = <0>; ++ clocks = <&irs1125_clk>; ++ pwdn-gpios = <&gpio 5 0>; ++ ++ irs1125_clk: camera-clk { ++ compatible = "fixed-clock"; ++ #clock-cells = <0>; ++ clock-frequency = <26000000>; ++ }; ++ ++ port { ++ sensor_out: endpoint { ++ remote-endpoint = <&csiss_in>; ++ clock-lanes = <0>; ++ data-lanes = <1 2>; ++ }; ++ }; ++ }; diff --git a/target/linux/bcm27xx/patches-5.10/950-0166-media-i2c-Add-a-driver-for-the-Infineon-IRS1125-dept.patch b/target/linux/bcm27xx/patches-5.10/950-0166-media-i2c-Add-a-driver-for-the-Infineon-IRS1125-dept.patch new file mode 100644 index 0000000000..27507ff879 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0166-media-i2c-Add-a-driver-for-the-Infineon-IRS1125-dept.patch @@ -0,0 +1,1231 @@ +From 21da9db2602925f6584936c167c8ce9b81ab2e0a Mon Sep 17 00:00:00 2001 +From: Markus Proeller +Date: Thu, 10 Oct 2019 19:12:36 +0200 +Subject: [PATCH] media: i2c: Add a driver for the Infineon IRS1125 + depth sensor + +The Infineon IRS1125 is a time of flight depth sensor that +has a CSI-2 interface. + +Add a V4L2 subdevice driver for this device. + +Signed-off-by: Markus Proeller +--- + drivers/media/i2c/Kconfig | 12 + + drivers/media/i2c/Makefile | 1 + + drivers/media/i2c/irs1125.c | 1112 +++++++++++++++++++++++++++++++++++ + drivers/media/i2c/irs1125.h | 61 ++ + 4 files changed, 1186 insertions(+) + create mode 100644 drivers/media/i2c/irs1125.c + create mode 100644 drivers/media/i2c/irs1125.h + +--- a/drivers/media/i2c/Kconfig ++++ b/drivers/media/i2c/Kconfig +@@ -1060,6 +1060,18 @@ config VIDEO_OV13858 + This is a Video4Linux2 sensor driver for the OmniVision + OV13858 camera. + ++config VIDEO_IRS1125 ++ tristate "Infineon IRS1125 sensor support" ++ depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API ++ depends on MEDIA_CAMERA_SUPPORT ++ select V4L2_FWNODE ++ help ++ This is a Video4Linux2 sensor-level driver for the Infineon ++ IRS1125 camera. ++ ++ To compile this driver as a module, choose M here: the ++ module will be called irs1125. ++ + config VIDEO_VS6624 + tristate "ST VS6624 sensor support" + depends on VIDEO_V4L2 && I2C +--- a/drivers/media/i2c/Makefile ++++ b/drivers/media/i2c/Makefile +@@ -84,6 +84,7 @@ obj-$(CONFIG_VIDEO_OV8856) += ov8856.o + obj-$(CONFIG_VIDEO_OV9640) += ov9640.o + obj-$(CONFIG_VIDEO_OV9650) += ov9650.o + obj-$(CONFIG_VIDEO_OV13858) += ov13858.o ++obj-$(CONFIG_VIDEO_IRS1125) += irs1125.o + obj-$(CONFIG_VIDEO_MT9M001) += mt9m001.o + obj-$(CONFIG_VIDEO_MT9M032) += mt9m032.o + obj-$(CONFIG_VIDEO_MT9M111) += mt9m111.o +--- /dev/null ++++ b/drivers/media/i2c/irs1125.c +@@ -0,0 +1,1112 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * A V4L2 driver for Infineon IRS1125 TOF cameras. ++ * Copyright (C) 2018, pieye GmbH ++ * ++ * Based on V4L2 OmniVision OV5647 Image Sensor driver ++ * Copyright (C) 2016 Ramiro Oliveira ++ * ++ * DT / fwnode changes, and GPIO control taken from ov5640.c ++ * Copyright (C) 2011-2013 Freescale Semiconductor, Inc. All Rights Reserved. ++ * Copyright (C) 2014-2017 Mentor Graphics Inc. ++ * ++ */ ++ ++#include "irs1125.h" ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define CHECK_BIT(val, pos) ((val) & BIT(pos)) ++ ++#define SENSOR_NAME "irs1125" ++ ++#define RESET_ACTIVE_DELAY_MS 20 ++ ++#define IRS1125_ALTERNATE_FW "irs1125_af.bin" ++ ++#define IRS1125_REG_CSICFG 0xA882 ++#define IRS1125_REG_DESIGN_STEP 0xB0AD ++#define IRS1125_REG_EFUSEVAL2 0xB09F ++#define IRS1125_REG_EFUSEVAL3 0xB0A0 ++#define IRS1125_REG_EFUSEVAL4 0xB0A1 ++#define IRS1125_REG_DMEM_SHADOW 0xC320 ++ ++#define IRS1125_DESIGN_STEP_EXPECTED 0x0a12 ++ ++#define IRS1125_ROW_START_DEF 0 ++#define IRS1125_COLUMN_START_DEF 0 ++#define IRS1125_WINDOW_HEIGHT_DEF 288 ++#define IRS1125_WINDOW_WIDTH_DEF 352 ++ ++struct regval_list { ++ u16 addr; ++ u16 data; ++}; ++ ++struct irs1125 { ++ struct v4l2_subdev sd; ++ struct media_pad pad; ++ /* the parsed DT endpoint info */ ++ struct v4l2_fwnode_endpoint ep; ++ ++ struct clk *xclk; ++ struct v4l2_ctrl_handler ctrl_handler; ++ ++ /* To serialize asynchronus callbacks */ ++ struct mutex lock; ++ ++ /* image data layout */ ++ unsigned int num_seq; ++ ++ /* reset pin */ ++ struct gpio_desc *reset; ++ ++ /* V4l2 Controls to grab */ ++ struct v4l2_ctrl *ctrl_modplls; ++ struct v4l2_ctrl *ctrl_numseq; ++ ++ int power_count; ++}; ++ ++static inline struct irs1125 *to_state(struct v4l2_subdev *sd) ++{ ++ return container_of(sd, struct irs1125, sd); ++} ++ ++static struct regval_list irs1125_26MHz[] = { ++ {0xB017, 0x0413}, ++ {0xB086, 0x3535}, ++ {0xB0AE, 0xEF02}, ++ {0xA000, 0x0004}, ++ {0xFFFF, 100}, ++ ++ {0xB062, 0x6383}, ++ {0xB063, 0x55A8}, ++ {0xB068, 0x7628}, ++ {0xB069, 0x03E2}, ++ ++ {0xFFFF, 100}, ++ {0xB05A, 0x01C5}, ++ {0xB05C, 0x0206}, ++ {0xB05D, 0x01C5}, ++ {0xB05F, 0x0206}, ++ {0xB016, 0x1335}, ++ {0xFFFF, 100}, ++ {0xA893, 0x8261}, ++ {0xA894, 0x89d8}, ++ {0xA895, 0x131d}, ++ {0xA896, 0x4251}, ++ {0xA897, 0x9D8A}, ++ {0xA898, 0x0BD8}, ++ {0xA899, 0x2245}, ++ {0xA89A, 0xAB9B}, ++ {0xA89B, 0x03B9}, ++ {0xA89C, 0x8041}, ++ {0xA89D, 0xE07E}, ++ {0xA89E, 0x0307}, ++ {0xFFFF, 100}, ++ {0xA88D, 0x0004}, ++ {0xA800, 0x0E68}, ++ {0xA801, 0x0000}, ++ {0xA802, 0x000C}, ++ {0xA803, 0x0000}, ++ {0xA804, 0x0E68}, ++ {0xA805, 0x0000}, ++ {0xA806, 0x0440}, ++ {0xA807, 0x0000}, ++ {0xA808, 0x0E68}, ++ {0xA809, 0x0000}, ++ {0xA80A, 0x0884}, ++ {0xA80B, 0x0000}, ++ {0xA80C, 0x0E68}, ++ {0xA80D, 0x0000}, ++ {0xA80E, 0x0CC8}, ++ {0xA80F, 0x0000}, ++ {0xA810, 0x0E68}, ++ {0xA811, 0x0000}, ++ {0xA812, 0x2000}, ++ {0xA813, 0x0000}, ++ {0xA882, 0x0081}, ++ {0xA88C, 0x403A}, ++ {0xA88F, 0x031E}, ++ {0xA892, 0x0351}, ++ {0x9813, 0x13FF}, ++ {0x981B, 0x7608}, ++ ++ {0xB008, 0x0000}, ++ {0xB015, 0x1513}, ++ ++ {0xFFFF, 100} ++}; ++ ++static struct regval_list irs1125_seq_cfg[] = { ++ {0xC3A0, 0x823D}, ++ {0xC3A1, 0xB13B}, ++ {0xC3A2, 0x0313}, ++ {0xC3A3, 0x4659}, ++ {0xC3A4, 0xC4EC}, ++ {0xC3A5, 0x03CE}, ++ {0xC3A6, 0x4259}, ++ {0xC3A7, 0xC4EC}, ++ {0xC3A8, 0x03CE}, ++ {0xC3A9, 0x8839}, ++ {0xC3AA, 0x89D8}, ++ {0xC3AB, 0x031D}, ++ ++ {0xC24C, 0x5529}, ++ {0xC24D, 0x0000}, ++ {0xC24E, 0x1200}, ++ {0xC24F, 0x6CB2}, ++ {0xC250, 0x0000}, ++ {0xC251, 0x5529}, ++ {0xC252, 0x42F4}, ++ {0xC253, 0xD1AF}, ++ {0xC254, 0x8A18}, ++ {0xC255, 0x0002}, ++ {0xC256, 0x5529}, ++ {0xC257, 0x6276}, ++ {0xC258, 0x11A7}, ++ {0xC259, 0xD907}, ++ {0xC25A, 0x0000}, ++ {0xC25B, 0x5529}, ++ {0xC25C, 0x07E0}, ++ {0xC25D, 0x7BFE}, ++ {0xC25E, 0x6402}, ++ {0xC25F, 0x0019}, ++ ++ {0xC3AC, 0x0007}, ++ {0xC3AD, 0xED88}, ++ {0xC320, 0x003E}, ++ {0xC321, 0x0000}, ++ {0xC322, 0x2000}, ++ {0xC323, 0x0000}, ++ {0xC324, 0x0271}, ++ {0xC325, 0x0000}, ++ {0xC326, 0x000C}, ++ {0xC327, 0x0000}, ++ {0xC328, 0x0271}, ++ {0xC329, 0x0000}, ++ {0xC32A, 0x0440}, ++ {0xC32B, 0x0000}, ++ {0xC32C, 0x0271}, ++ {0xC32D, 0x0000}, ++ {0xC32E, 0x0884}, ++ {0xC32F, 0x0000}, ++ {0xC330, 0x0271}, ++ {0xC331, 0x0000}, ++ {0xC332, 0x0CC8}, ++ {0xC333, 0x0000}, ++ {0xA88D, 0x0004}, ++ ++ {0xA890, 0x0000}, ++ {0xC219, 0x0002}, ++ {0xC21A, 0x0000}, ++ {0xC21B, 0x0000}, ++ {0xC21C, 0x00CD}, ++ {0xC21D, 0x0009}, ++ {0xC21E, 0x00CD}, ++ {0xC21F, 0x0009}, ++ ++ {0xA87C, 0x0000}, ++ {0xC032, 0x0001}, ++ {0xC034, 0x0000}, ++ {0xC035, 0x0001}, ++ {0xC039, 0x0000}, ++ {0xC401, 0x0002}, ++ ++ {0xFFFF, 1}, ++ {0xA87C, 0x0001} ++}; ++ ++static int irs1125_write(struct v4l2_subdev *sd, u16 reg, u16 val) ++{ ++ int ret; ++ unsigned char data[4] = { reg >> 8, reg & 0xff, val >> 8, val & 0xff}; ++ struct i2c_client *client = v4l2_get_subdevdata(sd); ++ ++ ret = i2c_master_send(client, data, 4); ++ if (ret < 0) ++ dev_err(&client->dev, "%s: i2c write error, reg: %x\n", ++ __func__, reg); ++ ++ return ret; ++} ++ ++static int irs1125_read(struct v4l2_subdev *sd, u16 reg, u16 *val) ++{ ++ int ret; ++ unsigned char data_w[2] = { reg >> 8, reg & 0xff }; ++ char rdval[2]; ++ ++ struct i2c_client *client = v4l2_get_subdevdata(sd); ++ ++ ret = i2c_master_send(client, data_w, 2); ++ if (ret < 0) { ++ dev_dbg(&client->dev, "%s: i2c write error, reg: %x\n", ++ __func__, reg); ++ return ret; ++ } ++ ++ ret = i2c_master_recv(client, rdval, 2); ++ if (ret < 0) ++ dev_err(&client->dev, "%s: i2c read error, reg: %x\n", ++ __func__, reg); ++ ++ *val = rdval[1] | (rdval[0] << 8); ++ ++ return ret; ++} ++ ++static int irs1125_write_array(struct v4l2_subdev *sd, ++ struct regval_list *regs, int array_size) ++{ ++ int i, ret; ++ ++ for (i = 0; i < array_size; i++) { ++ if (regs[i].addr == 0xFFFF) { ++ msleep(regs[i].data); ++ } else { ++ ret = irs1125_write(sd, regs[i].addr, regs[i].data); ++ if (ret < 0) ++ return ret; ++ } ++ } ++ ++ return 0; ++} ++ ++static int irs1125_stream_on(struct v4l2_subdev *sd) ++{ ++ int ret; ++ struct irs1125 *irs1125 = to_state(sd); ++ struct i2c_client *client = v4l2_get_subdevdata(sd); ++ ++ v4l2_ctrl_grab(irs1125->ctrl_numseq, 1); ++ v4l2_ctrl_grab(irs1125->ctrl_modplls, 1); ++ ++ ret = irs1125_write(sd, 0xC400, 0x0001); ++ if (ret < 0) { ++ dev_err(&client->dev, "error enabling firmware: %d", ret); ++ return ret; ++ } ++ ++ msleep(100); ++ ++ return irs1125_write(sd, 0xA87C, 0x0001); ++} ++ ++static int irs1125_stream_off(struct v4l2_subdev *sd) ++{ ++ int ret; ++ struct irs1125 *irs1125 = to_state(sd); ++ struct i2c_client *client = v4l2_get_subdevdata(sd); ++ ++ v4l2_ctrl_grab(irs1125->ctrl_numseq, 0); ++ v4l2_ctrl_grab(irs1125->ctrl_modplls, 0); ++ ++ ret = irs1125_write(sd, 0xA87C, 0x0000); ++ if (ret < 0) { ++ dev_err(&client->dev, "error disabling trigger: %d", ret); ++ return ret; ++ } ++ ++ msleep(100); ++ ++ return irs1125_write(sd, 0xC400, 0x0002); ++} ++ ++static int __sensor_init(struct v4l2_subdev *sd) ++{ ++ unsigned int cnt, idx; ++ int ret; ++ u16 val; ++ struct i2c_client *client = v4l2_get_subdevdata(sd); ++ struct irs1125 *irs1125 = to_state(sd); ++ const struct firmware *fw; ++ struct regval_list *reg_data; ++ ++ cnt = 0; ++ while (1) { ++ ret = irs1125_read(sd, 0xC40F, &val); ++ if (ret < 0) { ++ dev_err(&client->dev, "read register 0xC40F failed\n"); ++ return ret; ++ } ++ if (CHECK_BIT(val, 14) == 0) ++ break; ++ ++ if (cnt >= 5) { ++ dev_err(&client->dev, "timeout waiting for 0xC40F\n"); ++ return -EAGAIN; ++ } ++ ++ cnt++; ++ } ++ ++ ret = irs1125_write_array(sd, irs1125_26MHz, ++ ARRAY_SIZE(irs1125_26MHz)); ++ if (ret < 0) { ++ dev_err(&client->dev, "write sensor default regs error\n"); ++ return ret; ++ } ++ ++ /* set CSI-2 number of data lanes */ ++ if (irs1125->ep.bus.mipi_csi2.num_data_lanes == 1) { ++ val = 0x0001; ++ } else if (irs1125->ep.bus.mipi_csi2.num_data_lanes == 2) { ++ val = 0x0081; ++ } else { ++ dev_err(&client->dev, "invalid number of data lanes %d\n", ++ irs1125->ep.bus.mipi_csi2.num_data_lanes); ++ return -EINVAL; ++ } ++ ++ ret = irs1125_write(sd, IRS1125_REG_CSICFG, val); ++ if (ret < 0) { ++ dev_err(&client->dev, "write sensor csi2 config error\n"); ++ return ret; ++ } ++ ++ /* request the firmware, this will block and timeout */ ++ ret = request_firmware(&fw, IRS1125_ALTERNATE_FW, &client->dev); ++ if (ret) { ++ dev_err(&client->dev, ++ "did not find the firmware file '%s' (status %d)\n", ++ IRS1125_ALTERNATE_FW, ret); ++ return ret; ++ } ++ ++ if (fw->size % 4) { ++ dev_err(&client->dev, "firmware file '%s' invalid\n", ++ IRS1125_ALTERNATE_FW); ++ release_firmware(fw); ++ return -EINVAL; ++ } ++ ++ for (idx = 0; idx < fw->size; idx += 4) { ++ reg_data = (struct regval_list *)&fw->data[idx]; ++ ret = irs1125_write(sd, reg_data->addr, reg_data->data); ++ if (ret < 0) { ++ dev_err(&client->dev, "firmware write error\n"); ++ release_firmware(fw); ++ return ret; ++ } ++ } ++ release_firmware(fw); ++ ++ ret = irs1125_write_array(sd, irs1125_seq_cfg, ++ ARRAY_SIZE(irs1125_seq_cfg)); ++ if (ret < 0) { ++ dev_err(&client->dev, "write default sequence failed\n"); ++ return ret; ++ } ++ ++ return 0; ++} ++ ++static int irs1125_sensor_power(struct v4l2_subdev *sd, int on) ++{ ++ int ret = 0; ++ struct irs1125 *irs1125 = to_state(sd); ++ struct i2c_client *client = v4l2_get_subdevdata(sd); ++ ++ mutex_lock(&irs1125->lock); ++ ++ if (on && !irs1125->power_count) { ++ gpiod_set_value_cansleep(irs1125->reset, 1); ++ msleep(RESET_ACTIVE_DELAY_MS); ++ ++ ret = clk_prepare_enable(irs1125->xclk); ++ if (ret < 0) { ++ dev_err(&client->dev, "clk prepare enable failed\n"); ++ goto out; ++ } ++ ++ ret = __sensor_init(sd); ++ if (ret < 0) { ++ clk_disable_unprepare(irs1125->xclk); ++ dev_err(&client->dev, ++ "Camera not available, check Power\n"); ++ goto out; ++ } ++ } else if (!on && irs1125->power_count == 1) { ++ gpiod_set_value_cansleep(irs1125->reset, 0); ++ } ++ ++ /* Update the power count. */ ++ irs1125->power_count += on ? 1 : -1; ++ WARN_ON(irs1125->power_count < 0); ++ ++out: ++ mutex_unlock(&irs1125->lock); ++ ++ return ret; ++} ++ ++#ifdef CONFIG_VIDEO_ADV_DEBUG ++static int irs1125_sensor_get_register(struct v4l2_subdev *sd, ++ struct v4l2_dbg_register *reg) ++{ ++ u16 val; ++ int ret; ++ ++ ret = irs1125_read(sd, reg->reg & 0xffff, &val); ++ if (ret < 0) ++ return ret; ++ ++ reg->val = val; ++ reg->size = 1; ++ ++ return 0; ++} ++ ++static int irs1125_sensor_set_register(struct v4l2_subdev *sd, ++ const struct v4l2_dbg_register *reg) ++{ ++ return irs1125_write(sd, reg->reg & 0xffff, reg->val & 0xffff); ++} ++#endif ++ ++static const struct v4l2_subdev_core_ops irs1125_subdev_core_ops = { ++ .s_power = irs1125_sensor_power, ++#ifdef CONFIG_VIDEO_ADV_DEBUG ++ .g_register = irs1125_sensor_get_register, ++ .s_register = irs1125_sensor_set_register, ++#endif ++}; ++ ++static int irs1125_s_stream(struct v4l2_subdev *sd, int enable) ++{ ++ if (enable) ++ return irs1125_stream_on(sd); ++ else ++ return irs1125_stream_off(sd); ++} ++ ++static const struct v4l2_subdev_video_ops irs1125_subdev_video_ops = { ++ .s_stream = irs1125_s_stream, ++}; ++ ++static int irs1125_enum_mbus_code(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_mbus_code_enum *code) ++{ ++ if (code->index > 0) ++ return -EINVAL; ++ ++ code->code = MEDIA_BUS_FMT_Y12_1X12; ++ ++ return 0; ++} ++ ++static int irs1125_set_get_fmt(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_format *format) ++{ ++ struct v4l2_mbus_framefmt *fmt = &format->format; ++ struct irs1125 *irs1125 = to_state(sd); ++ ++ if (format->pad != 0) ++ return -EINVAL; ++ ++ /* Only one format is supported, so return that */ ++ memset(fmt, 0, sizeof(*fmt)); ++ fmt->code = MEDIA_BUS_FMT_Y12_1X12; ++ fmt->colorspace = V4L2_COLORSPACE_RAW; ++ fmt->field = V4L2_FIELD_NONE; ++ fmt->width = IRS1125_WINDOW_WIDTH_DEF; ++ fmt->height = IRS1125_WINDOW_HEIGHT_DEF * irs1125->num_seq; ++ ++ return 0; ++} ++ ++static const struct v4l2_subdev_pad_ops irs1125_subdev_pad_ops = { ++ .enum_mbus_code = irs1125_enum_mbus_code, ++ .set_fmt = irs1125_set_get_fmt, ++ .get_fmt = irs1125_set_get_fmt, ++}; ++ ++static const struct v4l2_subdev_ops irs1125_subdev_ops = { ++ .core = &irs1125_subdev_core_ops, ++ .video = &irs1125_subdev_video_ops, ++ .pad = &irs1125_subdev_pad_ops, ++}; ++ ++static int irs1125_s_ctrl(struct v4l2_ctrl *ctrl) ++{ ++ struct irs1125 *dev = container_of(ctrl->handler, ++ struct irs1125, ctrl_handler); ++ struct i2c_client *client = v4l2_get_subdevdata(&dev->sd); ++ int err, i; ++ struct irs1125_mod_pll *mod_cur, *mod_new; ++ struct irs1125_seq_cfg *cfg_cur, *cfg_new; ++ u16 addr, val; ++ ++ err = 0; ++ ++ switch (ctrl->id) { ++ case IRS1125_CID_SAFE_RECONFIG: ++ { ++ struct irs1125_illu *illu_cur, *illu_new; ++ ++ illu_new = (struct irs1125_illu *)ctrl->p_new.p; ++ illu_cur = (struct irs1125_illu *)ctrl->p_cur.p; ++ for (i = 0; i < IRS1125_NUM_SEQ_ENTRIES; i++) { ++ if (illu_cur[i].exposure != illu_new[i].exposure) { ++ addr = 0xA850 + i * 2; ++ val = illu_new[i].exposure; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ if (illu_cur[i].framerate != illu_new[i].framerate) { ++ addr = 0xA851 + i * 2; ++ val = illu_new[i].framerate; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ } ++ break; ++ } ++ case IRS1125_CID_MOD_PLL: ++ mod_new = (struct irs1125_mod_pll *)ctrl->p_new.p; ++ mod_cur = (struct irs1125_mod_pll *)ctrl->p_cur.p; ++ for (i = 0; i < IRS1125_NUM_MOD_PLLS; i++) { ++ if (mod_cur[i].pllcfg1 != mod_new[i].pllcfg1) { ++ addr = 0xC3A0 + i * 3; ++ val = mod_new[i].pllcfg1; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ if (mod_cur[i].pllcfg2 != mod_new[i].pllcfg2) { ++ addr = 0xC3A1 + i * 3; ++ val = mod_new[i].pllcfg2; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ if (mod_cur[i].pllcfg3 != mod_new[i].pllcfg3) { ++ addr = 0xC3A2 + i * 3; ++ val = mod_new[i].pllcfg3; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ if (mod_cur[i].pllcfg4 != mod_new[i].pllcfg4) { ++ addr = 0xC24C + i * 5; ++ val = mod_new[i].pllcfg4; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ if (mod_cur[i].pllcfg5 != mod_new[i].pllcfg5) { ++ addr = 0xC24D + i * 5; ++ val = mod_new[i].pllcfg5; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ if (mod_cur[i].pllcfg6 != mod_new[i].pllcfg6) { ++ addr = 0xC24E + i * 5; ++ val = mod_new[i].pllcfg6; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ if (mod_cur[i].pllcfg7 != mod_new[i].pllcfg7) { ++ addr = 0xC24F + i * 5; ++ val = mod_new[i].pllcfg7; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ if (mod_cur[i].pllcfg8 != mod_new[i].pllcfg8) { ++ addr = 0xC250 + i * 5; ++ val = mod_new[i].pllcfg8; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ } ++ break; ++ case IRS1125_CID_SEQ_CONFIG: ++ cfg_new = (struct irs1125_seq_cfg *)ctrl->p_new.p; ++ cfg_cur = (struct irs1125_seq_cfg *)ctrl->p_cur.p; ++ for (i = 0; i < IRS1125_NUM_SEQ_ENTRIES; i++) { ++ if (cfg_cur[i].exposure != cfg_new[i].exposure) { ++ addr = IRS1125_REG_DMEM_SHADOW + i * 4; ++ val = cfg_new[i].exposure; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ if (cfg_cur[i].framerate != cfg_new[i].framerate) { ++ addr = IRS1125_REG_DMEM_SHADOW + 1 + i * 4; ++ val = cfg_new[i].framerate; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ if (cfg_cur[i].ps != cfg_new[i].ps) { ++ addr = IRS1125_REG_DMEM_SHADOW + 2 + i * 4; ++ val = cfg_new[i].ps; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ if (cfg_cur[i].pll != cfg_new[i].pll) { ++ addr = IRS1125_REG_DMEM_SHADOW + 3 + i * 4; ++ val = cfg_new[i].pll; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ } ++ } ++ break; ++ case IRS1125_CID_NUM_SEQS: ++ err = irs1125_write(&dev->sd, 0xA88D, ctrl->val - 1); ++ if (err >= 0) ++ dev->num_seq = ctrl->val; ++ break; ++ case IRS1125_CID_CONTINUOUS_TRIG: ++ if (ctrl->val == 0) ++ err = irs1125_write(&dev->sd, 0xA87C, 0); ++ else ++ err = irs1125_write(&dev->sd, 0xA87C, 1); ++ break; ++ case IRS1125_CID_TRIGGER: ++ if (ctrl->val != 0) { ++ err = irs1125_write(&dev->sd, 0xA87C, 1); ++ if (err >= 0) ++ err = irs1125_write(&dev->sd, 0xA87C, 0); ++ } ++ break; ++ case IRS1125_CID_RECONFIG: ++ if (ctrl->val != 0) ++ err = irs1125_write(&dev->sd, 0xA87A, 1); ++ break; ++ case IRS1125_CID_ILLU_ON: ++ if (ctrl->val == 0) ++ err = irs1125_write(&dev->sd, 0xA892, 0x377); ++ else ++ err = irs1125_write(&dev->sd, 0xA892, 0x355); ++ break; ++ default: ++ break; ++ } ++ ++ if (err < 0) ++ dev_err(&client->dev, "Error executing control ID: %d, val %d, err %d", ++ ctrl->id, ctrl->val, err); ++ else ++ err = 0; ++ ++ return err; ++} ++ ++static const struct v4l2_ctrl_ops irs1125_ctrl_ops = { ++ .s_ctrl = irs1125_s_ctrl, ++}; ++ ++static const struct v4l2_ctrl_config irs1125_custom_ctrls[] = { ++ { ++ .ops = &irs1125_ctrl_ops, ++ .id = IRS1125_CID_NUM_SEQS, ++ .name = "Change number of sequences", ++ .type = V4L2_CTRL_TYPE_INTEGER, ++ .flags = V4L2_CTRL_FLAG_MODIFY_LAYOUT, ++ .min = 1, ++ .max = 20, ++ .step = 1, ++ .def = 5, ++ }, { ++ .ops = &irs1125_ctrl_ops, ++ .id = IRS1125_CID_MOD_PLL, ++ .name = "Reconfigure modulation PLLs", ++ .type = V4L2_CTRL_TYPE_U16, ++ .flags = V4L2_CTRL_FLAG_HAS_PAYLOAD, ++ .min = 0, ++ .max = U16_MAX, ++ .step = 1, ++ .def = 0, ++ .elem_size = sizeof(u16), ++ .dims = {sizeof(struct irs1125_mod_pll) / sizeof(u16), ++ IRS1125_NUM_MOD_PLLS} ++ }, { ++ .ops = &irs1125_ctrl_ops, ++ .id = IRS1125_CID_SAFE_RECONFIG, ++ .name = "Change exposure and pause of single seq", ++ .type = V4L2_CTRL_TYPE_U16, ++ .flags = V4L2_CTRL_FLAG_HAS_PAYLOAD, ++ .min = 0, ++ .max = U16_MAX, ++ .step = 1, ++ .def = 0, ++ .elem_size = sizeof(u16), ++ .dims = {sizeof(struct irs1125_illu) / sizeof(u16), ++ IRS1125_NUM_SEQ_ENTRIES} ++ }, { ++ .ops = &irs1125_ctrl_ops, ++ .id = IRS1125_CID_SEQ_CONFIG, ++ .name = "Change sequence settings", ++ .type = V4L2_CTRL_TYPE_U16, ++ .flags = V4L2_CTRL_FLAG_HAS_PAYLOAD, ++ .min = 0, ++ .max = U16_MAX, ++ .step = 1, ++ .def = 0, ++ .elem_size = sizeof(u16), ++ .dims = {sizeof(struct irs1125_seq_cfg) / sizeof(u16), ++ IRS1125_NUM_SEQ_ENTRIES} ++ }, { ++ .ops = &irs1125_ctrl_ops, ++ .id = IRS1125_CID_CONTINUOUS_TRIG, ++ .name = "Enable/disable continuous trigger", ++ .type = V4L2_CTRL_TYPE_BOOLEAN, ++ .flags = V4L2_CTRL_FLAG_EXECUTE_ON_WRITE, ++ .min = 0, ++ .max = 1, ++ .step = 1, ++ .def = 0 ++ }, { ++ .ops = &irs1125_ctrl_ops, ++ .id = IRS1125_CID_TRIGGER, ++ .name = "Capture a single sequence", ++ .type = V4L2_CTRL_TYPE_BOOLEAN, ++ .flags = V4L2_CTRL_FLAG_EXECUTE_ON_WRITE, ++ .min = 0, ++ .max = 1, ++ .step = 1, ++ .def = 0 ++ }, { ++ .ops = &irs1125_ctrl_ops, ++ .id = IRS1125_CID_RECONFIG, ++ .name = "Trigger imager reconfiguration", ++ .type = V4L2_CTRL_TYPE_BOOLEAN, ++ .flags = V4L2_CTRL_FLAG_EXECUTE_ON_WRITE, ++ .min = 0, ++ .max = 1, ++ .step = 1, ++ .def = 0 ++ }, { ++ .ops = &irs1125_ctrl_ops, ++ .id = IRS1125_CID_ILLU_ON, ++ .name = "Turn illu on or off", ++ .type = V4L2_CTRL_TYPE_BOOLEAN, ++ .flags = V4L2_CTRL_FLAG_EXECUTE_ON_WRITE, ++ .min = 0, ++ .max = 1, ++ .step = 1, ++ .def = 1 ++ }, { ++ .ops = &irs1125_ctrl_ops, ++ .id = IRS1125_CID_IDENT0, ++ .name = "Get ident 0 information", ++ .type = V4L2_CTRL_TYPE_INTEGER, ++ .flags = V4L2_CTRL_FLAG_READ_ONLY, ++ .min = S32_MIN, ++ .max = S32_MAX, ++ .step = 1, ++ .def = 0 ++ }, { ++ .ops = &irs1125_ctrl_ops, ++ .id = IRS1125_CID_IDENT1, ++ .name = "Get ident 1 information", ++ .type = V4L2_CTRL_TYPE_INTEGER, ++ .flags = V4L2_CTRL_FLAG_READ_ONLY, ++ .min = S32_MIN, ++ .max = S32_MAX, ++ .step = 1, ++ .def = 0 ++ }, { ++ .ops = &irs1125_ctrl_ops, ++ .id = IRS1125_CID_IDENT2, ++ .name = "Get ident 2 information", ++ .type = V4L2_CTRL_TYPE_INTEGER, ++ .flags = V4L2_CTRL_FLAG_READ_ONLY, ++ .min = S32_MIN, ++ .max = S32_MAX, ++ .step = 1, ++ .def = 0 ++ } ++}; ++ ++static int irs1125_detect(struct v4l2_subdev *sd) ++{ ++ u16 read; ++ int ret; ++ struct i2c_client *client = v4l2_get_subdevdata(sd); ++ ++ ret = irs1125_read(sd, IRS1125_REG_DESIGN_STEP, &read); ++ if (ret < 0) { ++ dev_err(&client->dev, "error reading from i2c\n"); ++ return ret; ++ } ++ ++ if (read != IRS1125_DESIGN_STEP_EXPECTED) { ++ dev_err(&client->dev, "Design step expected 0x%x got 0x%x", ++ IRS1125_DESIGN_STEP_EXPECTED, read); ++ return -ENODEV; ++ } ++ ++ return 0; ++} ++ ++static int irs1125_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) ++{ ++ struct v4l2_mbus_framefmt *format = ++ v4l2_subdev_get_try_format(sd, fh->pad, 0); ++ ++ format->code = MEDIA_BUS_FMT_Y12_1X12; ++ format->width = IRS1125_WINDOW_WIDTH_DEF; ++ format->height = IRS1125_WINDOW_HEIGHT_DEF; ++ format->field = V4L2_FIELD_NONE; ++ format->colorspace = V4L2_COLORSPACE_RAW; ++ ++ return 0; ++} ++ ++static const struct v4l2_subdev_internal_ops irs1125_subdev_internal_ops = { ++ .open = irs1125_open, ++}; ++ ++static int irs1125_ctrls_init(struct irs1125 *sensor, struct device *dev) ++{ ++ struct v4l2_ctrl *ctrl; ++ int err, i; ++ struct v4l2_ctrl_handler *hdl; ++ ++ hdl = &sensor->ctrl_handler; ++ v4l2_ctrl_handler_init(hdl, ARRAY_SIZE(irs1125_custom_ctrls)); ++ ++ for (i = 0; i < ARRAY_SIZE(irs1125_custom_ctrls); i++) { ++ ctrl = v4l2_ctrl_new_custom(hdl, &irs1125_custom_ctrls[i], ++ NULL); ++ if (!ctrl) ++ dev_err(dev, "Failed to init custom control %s\n", ++ irs1125_custom_ctrls[i].name); ++ else if (irs1125_custom_ctrls[i].id == IRS1125_CID_NUM_SEQS) ++ sensor->ctrl_numseq = ctrl; ++ else if (irs1125_custom_ctrls[i].id == IRS1125_CID_MOD_PLL) ++ sensor->ctrl_modplls = ctrl; ++ } ++ ++ if (hdl->error) { ++ dev_err(dev, "Error %d adding controls\n", hdl->error); ++ err = hdl->error; ++ goto error_ctrls; ++ } ++ ++ sensor->sd.ctrl_handler = hdl; ++ return 0; ++ ++error_ctrls: ++ v4l2_ctrl_handler_free(&sensor->ctrl_handler); ++ return -err; ++} ++ ++static int irs1125_ident_setup(struct irs1125 *sensor, struct device *dev) ++{ ++ int ret; ++ struct v4l2_ctrl *ctrl; ++ struct v4l2_subdev *sd; ++ u16 read; ++ ++ sd = &sensor->sd; ++ ++ ctrl = v4l2_ctrl_find(&sensor->ctrl_handler, IRS1125_CID_IDENT0); ++ if (!ctrl) { ++ dev_err(dev, "could not find device ctrl.\n"); ++ return -EINVAL; ++ } ++ ++ ret = irs1125_read(sd, IRS1125_REG_EFUSEVAL2, &read); ++ if (ret < 0) { ++ dev_err(dev, "error reading from i2c\n"); ++ return -EIO; ++ } ++ ++ v4l2_ctrl_s_ctrl(ctrl, read); ++ ++ ctrl = v4l2_ctrl_find(&sensor->ctrl_handler, IRS1125_CID_IDENT1); ++ if (!ctrl) { ++ dev_err(dev, "could not find device ctrl.\n"); ++ return -EINVAL; ++ } ++ ++ ret = irs1125_read(sd, IRS1125_REG_EFUSEVAL3, &read); ++ if (ret < 0) { ++ dev_err(dev, "error reading from i2c\n"); ++ return -EIO; ++ } ++ ++ v4l2_ctrl_s_ctrl(ctrl, read); ++ ++ ctrl = v4l2_ctrl_find(&sensor->ctrl_handler, IRS1125_CID_IDENT2); ++ if (!ctrl) { ++ dev_err(dev, "could not find device ctrl.\n"); ++ return -EINVAL; ++ } ++ ++ ret = irs1125_read(sd, IRS1125_REG_EFUSEVAL4, &read); ++ if (ret < 0) { ++ dev_err(dev, "error reading from i2c\n"); ++ return -EIO; ++ } ++ v4l2_ctrl_s_ctrl(ctrl, read & 0xFFFC); ++ ++ return 0; ++} ++ ++static int irs1125_probe(struct i2c_client *client, ++ const struct i2c_device_id *id) ++{ ++ struct device *dev = &client->dev; ++ struct irs1125 *sensor; ++ int ret; ++ struct fwnode_handle *endpoint; ++ u32 xclk_freq; ++ int gpio_num; ++ ++ sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL); ++ if (!sensor) ++ return -ENOMEM; ++ ++ v4l2_i2c_subdev_init(&sensor->sd, client, &irs1125_subdev_ops); ++ ++ /* Get CSI2 bus config */ ++ endpoint = fwnode_graph_get_next_endpoint(dev_fwnode(dev), ++ NULL); ++ if (!endpoint) { ++ dev_err(dev, "endpoint node not found\n"); ++ return -EINVAL; ++ } ++ ++ ret = v4l2_fwnode_endpoint_parse(endpoint, &sensor->ep); ++ fwnode_handle_put(endpoint); ++ if (ret) { ++ dev_err(dev, "Could not parse endpoint\n"); ++ return ret; ++ } ++ ++ /* get system clock (xclk) */ ++ sensor->xclk = devm_clk_get(dev, NULL); ++ if (IS_ERR(sensor->xclk)) { ++ dev_err(dev, "could not get xclk"); ++ return PTR_ERR(sensor->xclk); ++ } ++ ++ xclk_freq = clk_get_rate(sensor->xclk); ++ if (xclk_freq != 26000000) { ++ dev_err(dev, "Unsupported clock frequency: %u\n", xclk_freq); ++ return -EINVAL; ++ } ++ ++ sensor->num_seq = 5; ++ ++ /* Request the power down GPIO */ ++ sensor->reset = devm_gpiod_get(&client->dev, "pwdn", ++ GPIOD_OUT_LOW); ++ ++ if (IS_ERR(sensor->reset)) { ++ dev_err(dev, "could not get reset"); ++ return PTR_ERR(sensor->reset); ++ } ++ ++ gpio_num = desc_to_gpio(sensor->reset); ++ ++ mutex_init(&sensor->lock); ++ ++ ret = irs1125_ctrls_init(sensor, dev); ++ if (ret < 0) ++ goto mutex_remove; ++ ++ sensor->sd.internal_ops = &irs1125_subdev_internal_ops; ++ sensor->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; ++ sensor->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR; ++ sensor->pad.flags = MEDIA_PAD_FL_SOURCE; ++ ret = media_entity_pads_init(&sensor->sd.entity, 1, &sensor->pad); ++ if (ret < 0) ++ goto mutex_remove; ++ ++ gpiod_set_value_cansleep(sensor->reset, 1); ++ msleep(RESET_ACTIVE_DELAY_MS); ++ ++ ret = irs1125_detect(&sensor->sd); ++ if (ret < 0) ++ goto error; ++ ++ ret = irs1125_ident_setup(sensor, dev); ++ if (ret < 0) ++ goto error; ++ ++ gpiod_set_value_cansleep(sensor->reset, 0); ++ ++ ret = v4l2_async_register_subdev(&sensor->sd); ++ if (ret < 0) ++ goto error; ++ ++ dev_dbg(dev, "Infineon IRS1125 camera driver probed\n"); ++ ++ return 0; ++ ++error: ++ media_entity_cleanup(&sensor->sd.entity); ++mutex_remove: ++ mutex_destroy(&sensor->lock); ++ return ret; ++} ++ ++static int irs1125_remove(struct i2c_client *client) ++{ ++ struct v4l2_subdev *sd = i2c_get_clientdata(client); ++ struct irs1125 *irs1125 = to_state(sd); ++ ++ v4l2_async_unregister_subdev(&irs1125->sd); ++ media_entity_cleanup(&irs1125->sd.entity); ++ v4l2_device_unregister_subdev(sd); ++ mutex_destroy(&irs1125->lock); ++ v4l2_ctrl_handler_free(&irs1125->ctrl_handler); ++ ++ return 0; ++} ++ ++#if IS_ENABLED(CONFIG_OF) ++static const struct of_device_id irs1125_of_match[] = { ++ { .compatible = "infineon,irs1125" }, ++ { /* sentinel */ }, ++}; ++MODULE_DEVICE_TABLE(of, irs1125_of_match); ++#endif ++ ++static struct i2c_driver irs1125_driver = { ++ .driver = { ++ .of_match_table = of_match_ptr(irs1125_of_match), ++ .name = SENSOR_NAME, ++ }, ++ .probe = irs1125_probe, ++ .remove = irs1125_remove, ++}; ++ ++module_i2c_driver(irs1125_driver); ++ ++MODULE_AUTHOR("Markus Proeller "); ++MODULE_DESCRIPTION("Infineon irs1125 sensor driver"); ++MODULE_LICENSE("GPL v2"); ++ +--- /dev/null ++++ b/drivers/media/i2c/irs1125.h +@@ -0,0 +1,61 @@ ++/* SPDX-License-Identifier: GPL-2.0 */ ++/* ++ * A V4L2 driver for Infineon IRS1125 TOF cameras. ++ * Copyright (C) 2018, pieye GmbH ++ * ++ * Based on V4L2 OmniVision OV5647 Image Sensor driver ++ * Copyright (C) 2016 Ramiro Oliveira ++ * ++ * DT / fwnode changes, and GPIO control taken from ov5640.c ++ * Copyright (C) 2011-2013 Freescale Semiconductor, Inc. All Rights Reserved. ++ * Copyright (C) 2014-2017 Mentor Graphics Inc. ++ * ++ */ ++ ++#ifndef IRS1125_H ++#define IRS1125_H ++ ++#include ++#include ++ ++#define IRS1125_NUM_SEQ_ENTRIES 20 ++#define IRS1125_NUM_MOD_PLLS 4 ++ ++#define IRS1125_CID_CUSTOM_BASE (V4L2_CID_USER_BASE | 0xf000) ++#define IRS1125_CID_SAFE_RECONFIG (IRS1125_CID_CUSTOM_BASE + 0) ++#define IRS1125_CID_CONTINUOUS_TRIG (IRS1125_CID_CUSTOM_BASE + 1) ++#define IRS1125_CID_TRIGGER (IRS1125_CID_CUSTOM_BASE + 2) ++#define IRS1125_CID_RECONFIG (IRS1125_CID_CUSTOM_BASE + 3) ++#define IRS1125_CID_ILLU_ON (IRS1125_CID_CUSTOM_BASE + 4) ++#define IRS1125_CID_NUM_SEQS (IRS1125_CID_CUSTOM_BASE + 5) ++#define IRS1125_CID_MOD_PLL (IRS1125_CID_CUSTOM_BASE + 6) ++#define IRS1125_CID_SEQ_CONFIG (IRS1125_CID_CUSTOM_BASE + 7) ++#define IRS1125_CID_IDENT0 (IRS1125_CID_CUSTOM_BASE + 8) ++#define IRS1125_CID_IDENT1 (IRS1125_CID_CUSTOM_BASE + 9) ++#define IRS1125_CID_IDENT2 (IRS1125_CID_CUSTOM_BASE + 10) ++ ++struct irs1125_seq_cfg { ++ __u16 exposure; ++ __u16 framerate; ++ __u16 ps; ++ __u16 pll; ++}; ++ ++struct irs1125_illu { ++ __u16 exposure; ++ __u16 framerate; ++}; ++ ++struct irs1125_mod_pll { ++ __u16 pllcfg1; ++ __u16 pllcfg2; ++ __u16 pllcfg3; ++ __u16 pllcfg4; ++ __u16 pllcfg5; ++ __u16 pllcfg6; ++ __u16 pllcfg7; ++ __u16 pllcfg8; ++}; ++ ++#endif /* IRS1125 */ ++ diff --git a/target/linux/bcm27xx/patches-5.10/950-0167-drm-v3d-Don-t-clear-MMU-control-bits-on-exception.patch b/target/linux/bcm27xx/patches-5.10/950-0167-drm-v3d-Don-t-clear-MMU-control-bits-on-exception.patch new file mode 100644 index 0000000000..19bb22080f --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0167-drm-v3d-Don-t-clear-MMU-control-bits-on-exception.patch @@ -0,0 +1,34 @@ +From 7372f1f8c151f752aa533eaf2b85ad9b21ec9639 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 11 Nov 2019 14:01:41 +0000 +Subject: [PATCH] drm/v3d: Don't clear MMU control bits on exception + +MMU exception conditions are reported in the V3D_MMU_CTRL register as +write-1-to-clear (W1C) bits. The MMU interrupt handling code clears any +exceptions, but does so by masking out any other bits and writing the +result back. There are some important control bits in that register, +including MMU_ENABLE, so a safer approach is to simply write back the +value just read unaltered. + +This patch doesn't remove the cause of the apparent PTE errors, but it +does reduce the impact to just an error in the kernel log. + +Signed-off-by: Phil Elwell +--- + drivers/gpu/drm/v3d/v3d_irq.c | 5 +---- + 1 file changed, 1 insertion(+), 4 deletions(-) + +--- a/drivers/gpu/drm/v3d/v3d_irq.c ++++ b/drivers/gpu/drm/v3d/v3d_irq.c +@@ -178,10 +178,7 @@ v3d_hub_irq(int irq, void *arg) + }; + const char *client = "?"; + +- V3D_WRITE(V3D_MMU_CTL, +- V3D_READ(V3D_MMU_CTL) & (V3D_MMU_CTL_CAP_EXCEEDED | +- V3D_MMU_CTL_PT_INVALID | +- V3D_MMU_CTL_WRITE_VIOLATION)); ++ V3D_WRITE(V3D_MMU_CTL, V3D_READ(V3D_MMU_CTL)); + + if (v3d->ver >= 41) { + axi_id = axi_id >> 5; diff --git a/target/linux/bcm27xx/patches-5.10/950-0168-drm-v3d-Suppress-all-but-the-first-MMU-error.patch b/target/linux/bcm27xx/patches-5.10/950-0168-drm-v3d-Suppress-all-but-the-first-MMU-error.patch new file mode 100644 index 0000000000..94647bc7da --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0168-drm-v3d-Suppress-all-but-the-first-MMU-error.patch @@ -0,0 +1,39 @@ +From e5d63db582ac8f702e6647c47e118c7e1b2412a3 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 11 Nov 2019 20:18:08 +0000 +Subject: [PATCH] drm/v3d: Suppress all but the first MMU error + +The v3d driver currently encounters a lot of MMU PTE exceptions, so +only log the first to avoid swamping the kernel log. + +Signed-off-by: Phil Elwell +--- + drivers/gpu/drm/v3d/v3d_irq.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/drivers/gpu/drm/v3d/v3d_irq.c ++++ b/drivers/gpu/drm/v3d/v3d_irq.c +@@ -177,6 +177,7 @@ v3d_hub_irq(int irq, void *arg) + "GMP", + }; + const char *client = "?"; ++ static int logged_error; + + V3D_WRITE(V3D_MMU_CTL, V3D_READ(V3D_MMU_CTL)); + +@@ -186,6 +187,7 @@ v3d_hub_irq(int irq, void *arg) + client = v3d41_axi_ids[axi_id]; + } + ++ if (!logged_error) + dev_err(v3d->drm.dev, "MMU error from client %s (%d) at 0x%llx%s%s%s\n", + client, axi_id, (long long)vio_addr, + ((intsts & V3D_HUB_INT_MMU_WRV) ? +@@ -194,6 +196,7 @@ v3d_hub_irq(int irq, void *arg) + ", pte invalid" : ""), + ((intsts & V3D_HUB_INT_MMU_CAP) ? + ", cap exceeded" : "")); ++ logged_error = 1; + status = IRQ_HANDLED; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0169-drm-v3d-Plug-dma_fence-leak.patch b/target/linux/bcm27xx/patches-5.10/950-0169-drm-v3d-Plug-dma_fence-leak.patch new file mode 100644 index 0000000000..b96ecc2238 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0169-drm-v3d-Plug-dma_fence-leak.patch @@ -0,0 +1,28 @@ +From 6ae6a3a41d658321aee47577d88cbbbef3ea6b78 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 12 Nov 2019 16:41:21 +0000 +Subject: [PATCH] drm/v3d: Plug dma_fence leak + +The irq_fence and done_fence are given a reference that is never +released. The necessary dma_fence_put()s seem to have been +deleted in error in an earlier commit. + +Fixes: 0b73676836b2 ("drm/v3d: Clock V3D down when not in use.") + +Signed-off-by: Phil Elwell +--- + drivers/gpu/drm/v3d/v3d_gem.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/drivers/gpu/drm/v3d/v3d_gem.c ++++ b/drivers/gpu/drm/v3d/v3d_gem.c +@@ -410,6 +410,9 @@ v3d_job_free(struct kref *ref) + } + xa_destroy(&job->deps); + ++ dma_fence_put(job->irq_fence); ++ dma_fence_put(job->done_fence); ++ + v3d_clock_up_put(v3d); + + kfree(job); diff --git a/target/linux/bcm27xx/patches-5.10/950-0170-staging-vchiq_arm-Register-vcsm-cma-as-a-platform-dr.patch b/target/linux/bcm27xx/patches-5.10/950-0170-staging-vchiq_arm-Register-vcsm-cma-as-a-platform-dr.patch new file mode 100644 index 0000000000..76e81fda43 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0170-staging-vchiq_arm-Register-vcsm-cma-as-a-platform-dr.patch @@ -0,0 +1,40 @@ +From 9999a14d45012bce466bd52449c3dcbeb1736367 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 6 Nov 2019 13:57:48 +0000 +Subject: [PATCH] staging: vchiq_arm: Register vcsm-cma as a platform + driver + +Following the same pattern as bcm2835-camera and bcm2835-audio, +register the vcsm-cma driver as a platform driver + +Signed-off-by: Dave Stevenson +--- + drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c ++++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c +@@ -109,6 +109,7 @@ static struct class *vchiq_class; + static DEFINE_SPINLOCK(msg_queue_spinlock); + static struct platform_device *bcm2835_camera; + static struct platform_device *bcm2835_audio; ++static struct platform_device *vcsm_cma; + + static struct vchiq_drvdata bcm2835_drvdata = { + .cache_line_size = 32, +@@ -2765,6 +2766,7 @@ static int vchiq_probe(struct platform_d + VCHIQ_VERSION, VCHIQ_VERSION_MIN, + MAJOR(vchiq_devid), MINOR(vchiq_devid)); + ++ vcsm_cma = vchiq_register_child(pdev, "vcsm-cma"); + bcm2835_camera = vchiq_register_child(pdev, "bcm2835-camera"); + bcm2835_audio = vchiq_register_child(pdev, "bcm2835_audio"); + +@@ -2781,6 +2783,7 @@ static int vchiq_remove(struct platform_ + { + platform_device_unregister(bcm2835_audio); + platform_device_unregister(bcm2835_camera); ++ platform_device_unregister(vcsm_cma); + vchiq_debugfs_deinit(); + device_destroy(vchiq_class, vchiq_devid); + cdev_del(&vchiq_cdev); diff --git a/target/linux/bcm27xx/patches-5.10/950-0171-staging-vchiq_arm-Register-bcm2835-codec-as-a-platfo.patch b/target/linux/bcm27xx/patches-5.10/950-0171-staging-vchiq_arm-Register-bcm2835-codec-as-a-platfo.patch new file mode 100644 index 0000000000..dea284e0e6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0171-staging-vchiq_arm-Register-bcm2835-codec-as-a-platfo.patch @@ -0,0 +1,40 @@ +From 49d23a9d1982010b7b677f3f5c78ffbf46e39d85 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 6 Nov 2019 13:57:58 +0000 +Subject: [PATCH] staging: vchiq_arm: Register bcm2835-codec as a + platform driver + +Following the same pattern as bcm2835-camera and bcm2835-audio, +register the V4L2 codec driver as a platform driver + +Signed-off-by: Dave Stevenson +--- + drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c ++++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c +@@ -109,6 +109,7 @@ static struct class *vchiq_class; + static DEFINE_SPINLOCK(msg_queue_spinlock); + static struct platform_device *bcm2835_camera; + static struct platform_device *bcm2835_audio; ++static struct platform_device *bcm2835_codec; + static struct platform_device *vcsm_cma; + + static struct vchiq_drvdata bcm2835_drvdata = { +@@ -2767,6 +2768,7 @@ static int vchiq_probe(struct platform_d + MAJOR(vchiq_devid), MINOR(vchiq_devid)); + + vcsm_cma = vchiq_register_child(pdev, "vcsm-cma"); ++ bcm2835_codec = vchiq_register_child(pdev, "bcm2835-codec"); + bcm2835_camera = vchiq_register_child(pdev, "bcm2835-camera"); + bcm2835_audio = vchiq_register_child(pdev, "bcm2835_audio"); + +@@ -2783,6 +2785,7 @@ static int vchiq_remove(struct platform_ + { + platform_device_unregister(bcm2835_audio); + platform_device_unregister(bcm2835_camera); ++ platform_device_unregister(bcm2835_codec); + platform_device_unregister(vcsm_cma); + vchiq_debugfs_deinit(); + device_destroy(vchiq_class, vchiq_devid); diff --git a/target/linux/bcm27xx/patches-5.10/950-0172-net-bcmgenet-The-second-IRQ-is-optional.patch b/target/linux/bcm27xx/patches-5.10/950-0172-net-bcmgenet-The-second-IRQ-is-optional.patch new file mode 100644 index 0000000000..34b3238ed6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0172-net-bcmgenet-The-second-IRQ-is-optional.patch @@ -0,0 +1,24 @@ +From 7f729e862d5d0f6605874393af075a6aa8e98bd5 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 14 Nov 2019 11:59:01 +0000 +Subject: [PATCH] net: bcmgenet: The second IRQ is optional + +As of 5.4, the kernel logs errors for absent IRQs unless requested +with platform_get_irq_optional. + +Signed-off-by: Phil Elwell +--- + drivers/gpu/drm/v3d/v3d_irq.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/gpu/drm/v3d/v3d_irq.c ++++ b/drivers/gpu/drm/v3d/v3d_irq.c +@@ -217,7 +217,7 @@ v3d_irq_init(struct v3d_dev *v3d) + V3D_CORE_WRITE(core, V3D_CTL_INT_CLR, V3D_CORE_IRQS); + V3D_WRITE(V3D_HUB_INT_CLR, V3D_HUB_IRQS); + +- irq1 = platform_get_irq(v3d_to_pdev(v3d), 1); ++ irq1 = platform_get_irq_optional(v3d_to_pdev(v3d), 1); + if (irq1 == -EPROBE_DEFER) + return irq1; + if (irq1 > 0) { diff --git a/target/linux/bcm27xx/patches-5.10/950-0173-net-phy-2711-Allow-ethernet-LED-mode-to-be-set-via-d.patch b/target/linux/bcm27xx/patches-5.10/950-0173-net-phy-2711-Allow-ethernet-LED-mode-to-be-set-via-d.patch new file mode 100644 index 0000000000..84ad9387f6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0173-net-phy-2711-Allow-ethernet-LED-mode-to-be-set-via-d.patch @@ -0,0 +1,46 @@ +From 3ab0c4b6aa76a4dedb51c4e800b5b4ba29187c46 Mon Sep 17 00:00:00 2001 +From: James Hughes +Date: Thu, 31 Oct 2019 14:39:44 +0000 +Subject: [PATCH] net:phy:2711 Allow ethernet LED mode to be set via + device tree + +Add device tree entries and code to allow the specification of +the lighting modes for the LED's on the ethernet connector. + +Signed-off-by: James Hughes +--- + drivers/net/phy/broadcom.c | 9 +++++++-- + 1 file changed, 7 insertions(+), 2 deletions(-) + +--- a/drivers/net/phy/broadcom.c ++++ b/drivers/net/phy/broadcom.c +@@ -313,6 +313,9 @@ static void bcm54xx_adjust_rxrefclk(stru + static int bcm54xx_config_init(struct phy_device *phydev) + { + int reg, err, val; ++ u32 led_modes[] = {BCM_LED_MULTICOLOR_LINK_ACT, ++ BCM_LED_MULTICOLOR_LINK_ACT}; ++ struct device_node *np = phydev->mdio.dev.of_node; + + reg = phy_read(phydev, MII_BCM54XX_ECR); + if (reg < 0) +@@ -368,6 +371,8 @@ static int bcm54xx_config_init(struct ph + + bcm54xx_phydsp_config(phydev); + ++ of_property_read_u32_array(np, "led-modes", led_modes, 2); ++ + /* Encode link speed into LED1 and LED3 pair (green/amber). + * Also flash these two LEDs on activity. This means configuring + * them for MULTICOLOR and encoding link/activity into them. +@@ -377,8 +382,8 @@ static int bcm54xx_config_init(struct ph + bcm_phy_write_shadow(phydev, BCM5482_SHD_LEDS1, val); + + val = BCM_LED_MULTICOLOR_IN_PHASE | +- BCM5482_SHD_LEDS1_LED1(BCM_LED_MULTICOLOR_LINK_ACT) | +- BCM5482_SHD_LEDS1_LED3(BCM_LED_MULTICOLOR_LINK_ACT); ++ BCM5482_SHD_LEDS1_LED1(led_modes[0]) | ++ BCM5482_SHD_LEDS1_LED3(led_modes[1]); + bcm_phy_write_exp(phydev, BCM_EXP_MULTICOLOR, val); + + return 0; diff --git a/target/linux/bcm27xx/patches-5.10/950-0174-net-phy-2711-Change-the-default-ethernet-LED-actions.patch b/target/linux/bcm27xx/patches-5.10/950-0174-net-phy-2711-Change-the-default-ethernet-LED-actions.patch new file mode 100644 index 0000000000..a6bf06b43c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0174-net-phy-2711-Change-the-default-ethernet-LED-actions.patch @@ -0,0 +1,33 @@ +From 0534ec9429d41d9a00851444498f11b222d350b8 Mon Sep 17 00:00:00 2001 +From: James Hughes +Date: Thu, 7 Nov 2019 14:59:59 +0000 +Subject: [PATCH] net:phy:2711 Change the default ethernet LED actions + +This should return default behaviour back to that of previous +releases. +--- + drivers/net/phy/broadcom.c | 6 +----- + 1 file changed, 1 insertion(+), 5 deletions(-) + +--- a/drivers/net/phy/broadcom.c ++++ b/drivers/net/phy/broadcom.c +@@ -314,7 +314,7 @@ static int bcm54xx_config_init(struct ph + { + int reg, err, val; + u32 led_modes[] = {BCM_LED_MULTICOLOR_LINK_ACT, +- BCM_LED_MULTICOLOR_LINK_ACT}; ++ BCM_LED_MULTICOLOR_LINK}; + struct device_node *np = phydev->mdio.dev.of_node; + + reg = phy_read(phydev, MII_BCM54XX_ECR); +@@ -373,10 +373,6 @@ static int bcm54xx_config_init(struct ph + + of_property_read_u32_array(np, "led-modes", led_modes, 2); + +- /* Encode link speed into LED1 and LED3 pair (green/amber). +- * Also flash these two LEDs on activity. This means configuring +- * them for MULTICOLOR and encoding link/activity into them. +- */ + val = BCM5482_SHD_LEDS1_LED1(BCM_LED_SRC_MULTICOLOR1) | + BCM5482_SHD_LEDS1_LED3(BCM_LED_SRC_MULTICOLOR1); + bcm_phy_write_shadow(phydev, BCM5482_SHD_LEDS1, val); diff --git a/target/linux/bcm27xx/patches-5.10/950-0175-v3d_drv-Handle-missing-clock-more-gracefully.patch b/target/linux/bcm27xx/patches-5.10/950-0175-v3d_drv-Handle-missing-clock-more-gracefully.patch new file mode 100644 index 0000000000..0596ba97f7 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0175-v3d_drv-Handle-missing-clock-more-gracefully.patch @@ -0,0 +1,27 @@ +From d26aa66c1e5b8c31547315d5421a83f0dd1eeef5 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Fri, 23 Aug 2019 16:34:38 +0100 +Subject: [PATCH] v3d_drv: Handle missing clock more gracefully + +Signed-off-by: popcornmix +--- + drivers/gpu/drm/v3d/v3d_drv.c | 8 ++++---- + 1 file changed, 4 insertions(+), 4 deletions(-) + +--- a/drivers/gpu/drm/v3d/v3d_drv.c ++++ b/drivers/gpu/drm/v3d/v3d_drv.c +@@ -290,10 +290,10 @@ static int v3d_platform_drm_probe(struct + } + + v3d->clk = devm_clk_get(dev, NULL); +- if (IS_ERR(v3d->clk)) { +- if (ret != -EPROBE_DEFER) +- dev_err(dev, "Failed to get clock\n"); +- goto dev_free; ++ if (IS_ERR_OR_NULL(v3d->clk)) { ++ if (PTR_ERR(v3d->clk) != -EPROBE_DEFER) ++ dev_err(dev, "Failed to get clock (%ld)\n", PTR_ERR(v3d->clk)); ++ return PTR_ERR(v3d->clk); + } + v3d->clk_up_rate = clk_get_rate(v3d->clk); + /* For downclocking, drop it to the minimum frequency we can get from diff --git a/target/linux/bcm27xx/patches-5.10/950-0176-v3d_gem-Kick-the-clock-so-firmware-knows-we-are-usin.patch b/target/linux/bcm27xx/patches-5.10/950-0176-v3d_gem-Kick-the-clock-so-firmware-knows-we-are-usin.patch new file mode 100644 index 0000000000..ac1f38f089 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0176-v3d_gem-Kick-the-clock-so-firmware-knows-we-are-usin.patch @@ -0,0 +1,27 @@ +From a29ca7c68f90f9e59e7bca36b52c738faf7851ad Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Thu, 5 Sep 2019 17:59:14 +0100 +Subject: [PATCH] v3d_gem: Kick the clock so firmware knows we are + using firmware clock interface + +Setting the v3d clock to low value allows firmware to handle dvfs in case +where v3d hardware is not being actively used (e.g. console use). + +Signed-off-by: popcornmix +--- + drivers/gpu/drm/v3d/v3d_gem.c | 4 ++++ + 1 file changed, 4 insertions(+) + +--- a/drivers/gpu/drm/v3d/v3d_gem.c ++++ b/drivers/gpu/drm/v3d/v3d_gem.c +@@ -920,6 +920,10 @@ v3d_gem_init(struct drm_device *dev) + mutex_init(&v3d->clk_lock); + INIT_DELAYED_WORK(&v3d->clk_down_work, v3d_clock_down_work); + ++ /* kick the clock so firmware knows we are using firmware clock interface */ ++ v3d_clock_up_get(v3d); ++ v3d_clock_up_put(v3d); ++ + /* Note: We don't allocate address 0. Various bits of HW + * treat 0 as special, such as the occlusion query counters + * where 0 means "disabled". diff --git a/target/linux/bcm27xx/patches-5.10/950-0177-clk-raspberrypi-Allow-cpufreq-driver-to-also-adjust-.patch b/target/linux/bcm27xx/patches-5.10/950-0177-clk-raspberrypi-Allow-cpufreq-driver-to-also-adjust-.patch new file mode 100644 index 0000000000..258f058529 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0177-clk-raspberrypi-Allow-cpufreq-driver-to-also-adjust-.patch @@ -0,0 +1,25 @@ +From 9111e23e3749f49ec35e062c3c7e9a46ebbd8642 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Mon, 9 Sep 2019 15:49:56 +0100 +Subject: [PATCH] clk-raspberrypi: Allow cpufreq driver to also adjust + gpu clocks + +For performance/power it is beneficial to adjust gpu clocks with arm clock. +This is how the downstream cpufreq driver works + +Signed-off-by: popcornmix +--- + drivers/clk/bcm/clk-raspberrypi.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/clk/bcm/clk-raspberrypi.c ++++ b/drivers/clk/bcm/clk-raspberrypi.c +@@ -97,7 +97,7 @@ static int raspberrypi_clock_property(st + struct raspberrypi_firmware_prop msg = { + .id = cpu_to_le32(data->id), + .val = cpu_to_le32(*val), +- .disable_turbo = cpu_to_le32(1), ++ .disable_turbo = cpu_to_le32(0), + }; + int ret; + diff --git a/target/linux/bcm27xx/patches-5.10/950-0178-clk-bcm2835-Disable-v3d-clock.patch b/target/linux/bcm27xx/patches-5.10/950-0178-clk-bcm2835-Disable-v3d-clock.patch new file mode 100644 index 0000000000..b1e46d95cb --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0178-clk-bcm2835-Disable-v3d-clock.patch @@ -0,0 +1,58 @@ +From dcfed6cdcd38f9b0ca706af74710969aa8082c38 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Tue, 3 Sep 2019 20:28:00 +0100 +Subject: [PATCH] clk-bcm2835: Disable v3d clock + +This is controlled by firmware, see clk-raspberrypi.c + +Signed-off-by: popcornmix +--- + drivers/clk/bcm/clk-bcm2835.c | 30 ++++++++++++------------------ + 1 file changed, 12 insertions(+), 18 deletions(-) + +--- a/drivers/clk/bcm/clk-bcm2835.c ++++ b/drivers/clk/bcm/clk-bcm2835.c +@@ -1741,16 +1741,12 @@ static const struct bcm2835_clk_desc clk + .hold_mask = CM_PLLA_HOLDCORE, + .fixed_divider = 1, + .flags = CLK_SET_RATE_PARENT), +- [BCM2835_PLLA_PER] = REGISTER_PLL_DIV( +- SOC_ALL, +- .name = "plla_per", +- .source_pll = "plla", +- .cm_reg = CM_PLLA, +- .a2w_reg = A2W_PLLA_PER, +- .load_mask = CM_PLLA_LOADPER, +- .hold_mask = CM_PLLA_HOLDPER, +- .fixed_divider = 1, +- .flags = CLK_SET_RATE_PARENT), ++ ++ /* ++ * PLLA_PER is used for gpu clocks. Controlled by firmware, see ++ * clk-raspberrypi.c. ++ */ ++ + [BCM2835_PLLA_DSI0] = REGISTER_PLL_DIV( + SOC_ALL, + .name = "plla_dsi0", +@@ -2051,14 +2047,12 @@ static const struct bcm2835_clk_desc clk + .int_bits = 6, + .frac_bits = 0, + .tcnt_mux = 3), +- [BCM2835_CLOCK_V3D] = REGISTER_VPU_CLK( +- SOC_ALL, +- .name = "v3d", +- .ctl_reg = CM_V3DCTL, +- .div_reg = CM_V3DDIV, +- .int_bits = 4, +- .frac_bits = 8, +- .tcnt_mux = 4), ++ ++ /* ++ * CLOCK_V3D is used for v3d clock. Controlled by firmware, see ++ * clk-raspberrypi.c. ++ */ ++ + /* + * VPU clock. This doesn't have an enable bit, since it drives + * the bus for everything else, and is special so it doesn't need diff --git a/target/linux/bcm27xx/patches-5.10/950-0179-drm-v3d-Set-dma_mask-as-well-as-coherent_dma_mask.patch b/target/linux/bcm27xx/patches-5.10/950-0179-drm-v3d-Set-dma_mask-as-well-as-coherent_dma_mask.patch new file mode 100644 index 0000000000..1289309a59 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0179-drm-v3d-Set-dma_mask-as-well-as-coherent_dma_mask.patch @@ -0,0 +1,27 @@ +From 0a34bafa5816dd1425550968ff7d3de2dc955e6f Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 22 Nov 2019 16:23:32 +0000 +Subject: [PATCH] drm/v3d: Set dma_mask as well as coherent_dma_mask + +Both coherent_dma_mask and dma_mask act as constraints on allocations +and bounce buffer usage, so be sure to set dma_mask to the appropriate +value otherwise the effective mask could be incorrect. + +Signed-off-by: Phil Elwell +--- + drivers/gpu/drm/v3d/v3d_drv.c | 4 ++-- + 1 file changed, 2 insertions(+), 2 deletions(-) + +--- a/drivers/gpu/drm/v3d/v3d_drv.c ++++ b/drivers/gpu/drm/v3d/v3d_drv.c +@@ -263,8 +263,8 @@ static int v3d_platform_drm_probe(struct + return ret; + + mmu_debug = V3D_READ(V3D_MMU_DEBUG_INFO); +- dev->coherent_dma_mask = +- DMA_BIT_MASK(30 + V3D_GET_FIELD(mmu_debug, V3D_MMU_PA_WIDTH)); ++ dma_set_mask_and_coherent(dev, ++ DMA_BIT_MASK(30 + V3D_GET_FIELD(mmu_debug, V3D_MMU_PA_WIDTH))); + v3d->va_width = 30 + V3D_GET_FIELD(mmu_debug, V3D_MMU_VA_WIDTH); + + ident1 = V3D_READ(V3D_HUB_IDENT1); diff --git a/target/linux/bcm27xx/patches-5.10/950-0180-staging-vchiq_arm-Set-up-dma-ranges-on-child-devices.patch b/target/linux/bcm27xx/patches-5.10/950-0180-staging-vchiq_arm-Set-up-dma-ranges-on-child-devices.patch new file mode 100644 index 0000000000..894ac6bb5d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0180-staging-vchiq_arm-Set-up-dma-ranges-on-child-devices.patch @@ -0,0 +1,33 @@ +From f18a78bd6232ebe254486740eb5f9bbdc4650879 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 29 Jan 2019 16:13:25 +0000 +Subject: [PATCH] staging: vchiq_arm: Set up dma ranges on child + devices + +The VCHIQ driver now loads the audio, camera, codec, and vc-sm +drivers as platform drivers. However they were not being given +the correct DMA configuration. + +Call of_dma_configure with the parent (VCHIQ) parameters to be +inherited by the child. + +Signed-off-by: Dave Stevenson +--- + .../staging/vc04_services/interface/vchiq_arm/vchiq_arm.c | 6 ++++++ + 1 file changed, 6 insertions(+) + +--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c ++++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c +@@ -2710,6 +2710,12 @@ vchiq_register_child(struct platform_dev + child = NULL; + } + ++ /* ++ * We want the dma-ranges etc to be copied from the parent VCHIQ device ++ * to be passed on to the children too. ++ */ ++ of_dma_configure(&new_dev->dev, pdev->dev.of_node, true); ++ + return child; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0181-staging-vchiq-Use-the-old-dma-controller-for-OF-conf.patch b/target/linux/bcm27xx/patches-5.10/950-0181-staging-vchiq-Use-the-old-dma-controller-for-OF-conf.patch new file mode 100644 index 0000000000..0f07dd8d25 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0181-staging-vchiq-Use-the-old-dma-controller-for-OF-conf.patch @@ -0,0 +1,51 @@ +From d7dbf1141d107ba6df15b04498e5fb88b6b61912 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 18 Jun 2019 12:15:50 +0100 +Subject: [PATCH] staging: vchiq: Use the old dma controller for OF + config on platform devices + +vchiq on Pi4 is no longer under the soc node, therefore it +doesn't get the dma-ranges for the VPU. + +Switch to using the configuration of the old dma controller as +that will set the dma-ranges correctly. + +Signed-off-by: Dave Stevenson +--- + .../interface/vchiq_arm/vchiq_arm.c | 17 ++++++++++++++--- + 1 file changed, 14 insertions(+), 3 deletions(-) + +--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c ++++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c +@@ -2696,6 +2696,7 @@ vchiq_register_child(struct platform_dev + { + struct platform_device_info pdevinfo; + struct platform_device *child; ++ struct device_node *np; + + memset(&pdevinfo, 0, sizeof(pdevinfo)); + +@@ -2711,10 +2712,20 @@ vchiq_register_child(struct platform_dev + } + + /* +- * We want the dma-ranges etc to be copied from the parent VCHIQ device +- * to be passed on to the children too. ++ * We want the dma-ranges etc to be copied from a device with the ++ * correct dma-ranges for the VPU. ++ * VCHIQ on Pi4 is now under scb which doesn't get those dma-ranges. ++ * Take the "dma" node as going to be suitable as it sees the world ++ * through the same eyes as the VPU. + */ +- of_dma_configure(&new_dev->dev, pdev->dev.of_node, true); ++ np = of_find_node_by_path("dma"); ++ if (!np) ++ np = pdev->dev.of_node; ++ ++ of_dma_configure(&child->dev, np, true); ++ ++ if (np != pdev->dev.of_node) ++ of_node_put(np); + + return child; + } diff --git a/target/linux/bcm27xx/patches-5.10/950-0182-ARM-bcm-Backport-BCM2711-support-from-upstream.patch b/target/linux/bcm27xx/patches-5.10/950-0182-ARM-bcm-Backport-BCM2711-support-from-upstream.patch new file mode 100644 index 0000000000..9f65d5d4fa --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0182-ARM-bcm-Backport-BCM2711-support-from-upstream.patch @@ -0,0 +1,47 @@ +From 20534fd2fedd5c3febd239475e64d3dfc7d8400b Mon Sep 17 00:00:00 2001 +From: Stefan Wahren +Date: Fri, 27 Dec 2019 11:40:56 +0100 +Subject: [PATCH] ARM: bcm: Backport BCM2711 support from upstream + +Make the BCM2711 a different machine, but keep it in board_bcm2835. + +Signed-off-by: Stefan Wahren +--- + arch/arm/mach-bcm/board_bcm2835.c | 17 +++++++++++++++-- + 1 file changed, 15 insertions(+), 2 deletions(-) + +--- a/arch/arm/mach-bcm/board_bcm2835.c ++++ b/arch/arm/mach-bcm/board_bcm2835.c +@@ -109,17 +109,30 @@ static const char * const bcm2835_compat + #ifdef CONFIG_ARCH_MULTI_V7 + "brcm,bcm2836", + "brcm,bcm2837", +- "brcm,bcm2711", + #endif + NULL + }; + + DT_MACHINE_START(BCM2835, "BCM2835") ++ .map_io = bcm2835_map_io, ++ .init_machine = bcm2835_init, ++ .dt_compat = bcm2835_compat, ++ .smp = smp_ops(bcm2836_smp_ops), ++MACHINE_END ++ ++static const char * const bcm2711_compat[] = { ++#ifdef CONFIG_ARCH_MULTI_V7 ++ "brcm,bcm2711", ++#endif ++ NULL ++}; ++ ++DT_MACHINE_START(BCM2711, "BCM2711") + #if defined(CONFIG_ZONE_DMA) && defined(CONFIG_ARM_LPAE) + .dma_zone_size = SZ_1G, + #endif + .map_io = bcm2835_map_io, + .init_machine = bcm2835_init, +- .dt_compat = bcm2835_compat, ++ .dt_compat = bcm2711_compat, + .smp = smp_ops(bcm2836_smp_ops), + MACHINE_END diff --git a/target/linux/bcm27xx/patches-5.10/950-0183-Initialise-rpi-firmware-before-clk-bcm2835.patch b/target/linux/bcm27xx/patches-5.10/950-0183-Initialise-rpi-firmware-before-clk-bcm2835.patch new file mode 100644 index 0000000000..dcd9ff4346 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0183-Initialise-rpi-firmware-before-clk-bcm2835.patch @@ -0,0 +1,47 @@ +From a4dd91006d4fdbd5c0f32e48eb7babc98ebc37f2 Mon Sep 17 00:00:00 2001 +From: Luke Hinds <7058938+lukehinds@users.noreply.github.com> +Date: Wed, 22 Jan 2020 16:03:00 +0000 +Subject: [PATCH] Initialise rpi-firmware before clk-bcm2835 + +The IMA (Integrity Measurement Architecture) looks for a TPM (Trusted +Platform Module) having been registered when it initialises; otherwise +it assumes there is no TPM. It has been observed on BCM2835 that IMA +is initialised before TPM, and that initialising the BCM2835 clock +driver before the firmware driver has the effect of reversing this +order. + +Change the firmware driver to initialise at core_initcall, delaying the +BCM2835 clock driver to postcore_initcall. + +See: https://github.com/raspberrypi/linux/issues/3291 + https://github.com/raspberrypi/linux/pull/3297 + +Signed-off-by: Luke Hinds +Co-authored-by: Phil Elwell +--- + drivers/clk/bcm/clk-bcm2835.c | 2 +- + drivers/firmware/raspberrypi.c | 2 +- + 2 files changed, 2 insertions(+), 2 deletions(-) + +--- a/drivers/clk/bcm/clk-bcm2835.c ++++ b/drivers/clk/bcm/clk-bcm2835.c +@@ -2429,7 +2429,7 @@ static int __init __bcm2835_clk_driver_i + { + return platform_driver_register(&bcm2835_clk_driver); + } +-core_initcall(__bcm2835_clk_driver_init); ++postcore_initcall(__bcm2835_clk_driver_init); + + MODULE_AUTHOR("Eric Anholt "); + MODULE_DESCRIPTION("BCM2835 clock driver"); +--- a/drivers/firmware/raspberrypi.c ++++ b/drivers/firmware/raspberrypi.c +@@ -430,7 +430,7 @@ out2: + out1: + return ret; + } +-subsys_initcall(rpi_firmware_init); ++core_initcall(rpi_firmware_init); + + static void __init rpi_firmware_exit(void) + { diff --git a/target/linux/bcm27xx/patches-5.10/950-0184-staging-vchiq_arm-Give-vchiq-children-DT-nodes.patch b/target/linux/bcm27xx/patches-5.10/950-0184-staging-vchiq_arm-Give-vchiq-children-DT-nodes.patch new file mode 100644 index 0000000000..f0457de0e8 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0184-staging-vchiq_arm-Give-vchiq-children-DT-nodes.patch @@ -0,0 +1,39 @@ +From 3e21610821310bfc015bbc8494e0e1f357e5a49e Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 3 Feb 2020 17:30:46 +0000 +Subject: [PATCH] staging: vchiq_arm: Give vchiq children DT nodes + +vchiq kernel clients are now instantiated as platform drivers rather +than using DT, but the children of the vchiq interface may still +benefit from access to DT properties. Give them the option of a +a sub-node of the vchiq parent for configuration and to allow +them to be disabled. + +Signed-off-by: Phil Elwell +--- + .../staging/vc04_services/interface/vchiq_arm/vchiq_arm.c | 8 ++++++++ + 1 file changed, 8 insertions(+) + +--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c ++++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c +@@ -2705,12 +2705,20 @@ vchiq_register_child(struct platform_dev + pdevinfo.id = PLATFORM_DEVID_NONE; + pdevinfo.dma_mask = DMA_BIT_MASK(32); + ++ np = of_get_child_by_name(pdev->dev.of_node, name); ++ ++ /* Skip the child if it is explicitly disabled */ ++ if (np && !of_device_is_available(np)) ++ return NULL; ++ + child = platform_device_register_full(&pdevinfo); + if (IS_ERR(child)) { + dev_warn(&pdev->dev, "%s not registered\n", name); + child = NULL; + } + ++ child->dev.of_node = np; ++ + /* + * We want the dma-ranges etc to be copied from a device with the + * correct dma-ranges for the VPU. diff --git a/target/linux/bcm27xx/patches-5.10/950-0185-pinctrl-bcm2835-Remove-gpiochip-on-error.patch b/target/linux/bcm27xx/patches-5.10/950-0185-pinctrl-bcm2835-Remove-gpiochip-on-error.patch new file mode 100644 index 0000000000..497c283325 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0185-pinctrl-bcm2835-Remove-gpiochip-on-error.patch @@ -0,0 +1,25 @@ +From 0da3ef334d4949431f34fea9f315d967e47a6a73 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 6 Jan 2020 16:04:30 +0000 +Subject: [PATCH] pinctrl: bcm2835: Remove gpiochip on error + +A failure in gpiochip_irqchip_add leads to a leak of a gpiochip. Fix +the leak with the use of devm_gpiochip_add_data. + +Fixes: 85ae9e512f43 ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP") +Signed-off-by: Phil Elwell +--- + drivers/pinctrl/bcm/pinctrl-bcm2835.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c ++++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c +@@ -1300,7 +1300,7 @@ static int bcm2835_pinctrl_probe(struct + girq->default_type = IRQ_TYPE_NONE; + girq->handler = handle_level_irq; + +- err = gpiochip_add_data(&pc->gpio_chip, pc); ++ err = devm_gpiochip_add_data(dev, &pc->gpio_chip, pc); + if (err) { + dev_err(dev, "could not add GPIO chip\n"); + return err; diff --git a/target/linux/bcm27xx/patches-5.10/950-0186-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch b/target/linux/bcm27xx/patches-5.10/950-0186-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch new file mode 100644 index 0000000000..2d13736fcb --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0186-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch @@ -0,0 +1,78 @@ +From 069990e0b524a7acdcfef0505913ee20401fec5a Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 6 Jan 2020 14:05:42 +0000 +Subject: [PATCH] pinctrl: bcm2835: Change init order for gpio hogs + +pinctrl-bcm2835 is a combined pinctrl/gpio driver. Currently the gpio +side is registered first, but this breaks gpio hogs (which are +configured during gpiochip_add_data). Part of the hog initialisation +is a call to pinctrl_gpio_request, and since the pinctrl driver hasn't +yet been registered this results in an -EPROBE_DEFER from which it can +never recover. + +Change the initialisation sequence to register the pinctrl driver +first. + +See: https://www.raspberrypi.org/forums/viewtopic.php?f=107&t=260600 + +Signed-off-by: Phil Elwell +--- + drivers/pinctrl/bcm/pinctrl-bcm2835.c | 29 +++++++++++++++------------ + 1 file changed, 16 insertions(+), 13 deletions(-) + +--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c ++++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c +@@ -1244,6 +1244,18 @@ static int bcm2835_pinctrl_probe(struct + raw_spin_lock_init(&pc->irq_lock[i]); + } + ++ pc->pctl_desc = *pdata->pctl_desc; ++ pc->pctl_dev = devm_pinctrl_register(dev, &pc->pctl_desc, pc); ++ if (IS_ERR(pc->pctl_dev)) { ++ gpiochip_remove(&pc->gpio_chip); ++ return PTR_ERR(pc->pctl_dev); ++ } ++ ++ pc->gpio_range = *pdata->gpio_range; ++ pc->gpio_range.base = pc->gpio_chip.base; ++ pc->gpio_range.gc = &pc->gpio_chip; ++ pinctrl_add_gpio_range(pc->pctl_dev, &pc->gpio_range); ++ + girq = &pc->gpio_chip.irq; + girq->chip = &bcm2835_gpio_irq_chip; + girq->parent_handler = bcm2835_gpio_irq_handler; +@@ -1251,8 +1263,10 @@ static int bcm2835_pinctrl_probe(struct + girq->parents = devm_kcalloc(dev, BCM2835_NUM_IRQS, + sizeof(*girq->parents), + GFP_KERNEL); +- if (!girq->parents) ++ if (!girq->parents) { ++ pinctrl_remove_gpio_range(pc->pctl_dev, &pc->gpio_range); + return -ENOMEM; ++ } + + if (is_7211) { + pc->wake_irq = devm_kcalloc(dev, BCM2835_NUM_IRQS, +@@ -1303,21 +1317,10 @@ static int bcm2835_pinctrl_probe(struct + err = devm_gpiochip_add_data(dev, &pc->gpio_chip, pc); + if (err) { + dev_err(dev, "could not add GPIO chip\n"); ++ pinctrl_remove_gpio_range(pc->pctl_dev, &pc->gpio_range); + return err; + } + +- pc->pctl_desc = *pdata->pctl_desc; +- pc->pctl_dev = devm_pinctrl_register(dev, &pc->pctl_desc, pc); +- if (IS_ERR(pc->pctl_dev)) { +- gpiochip_remove(&pc->gpio_chip); +- return PTR_ERR(pc->pctl_dev); +- } +- +- pc->gpio_range = *pdata->gpio_range; +- pc->gpio_range.base = pc->gpio_chip.base; +- pc->gpio_range.gc = &pc->gpio_chip; +- pinctrl_add_gpio_range(pc->pctl_dev, &pc->gpio_range); +- + return 0; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0187-pinctrl-bcm2835-Accept-fewer-than-expected-IRQs.patch b/target/linux/bcm27xx/patches-5.10/950-0187-pinctrl-bcm2835-Accept-fewer-than-expected-IRQs.patch new file mode 100644 index 0000000000..4456504ee8 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0187-pinctrl-bcm2835-Accept-fewer-than-expected-IRQs.patch @@ -0,0 +1,31 @@ +From 9ab71458b5475c7d8d42896721e593f6ef1a5c7a Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 25 Feb 2020 17:38:20 +0000 +Subject: [PATCH] pinctrl: bcm2835: Accept fewer than expected IRQs + +The downstream .dts files only request two GPIO IRQs. Truncate the +array of parent IRQs when irq_of_parse_and_map returns 0. + +Signed-off-by: Phil Elwell +--- + drivers/pinctrl/bcm/pinctrl-bcm2835.c | 8 ++++++-- + 1 file changed, 6 insertions(+), 2 deletions(-) + +--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c ++++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c +@@ -1288,9 +1288,13 @@ static int bcm2835_pinctrl_probe(struct + char *name; + + girq->parents[i] = irq_of_parse_and_map(np, i); +- if (!is_7211) ++ if (!is_7211) { ++ if (!girq->parents[i]) { ++ girq->num_parents = i; ++ break; ++ } + continue; +- ++ } + /* Skip over the all banks interrupts */ + pc->wake_irq[i] = irq_of_parse_and_map(np, i + + BCM2835_NUM_IRQS + 1); diff --git a/target/linux/bcm27xx/patches-5.10/950-0188-drivers-char-vcio-Use-common-compat-header.patch b/target/linux/bcm27xx/patches-5.10/950-0188-drivers-char-vcio-Use-common-compat-header.patch new file mode 100644 index 0000000000..f02e370859 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0188-drivers-char-vcio-Use-common-compat-header.patch @@ -0,0 +1,23 @@ +From b1c80253689fe3d451d08ec707907b2dca61ddc3 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 2 Mar 2020 14:40:19 +0000 +Subject: [PATCH] drivers: char: vcio: Use common compat header + +The definition of compat_ptr is now common for most platforms, but +requires the inclusion of . + +Signed-off-by: Phil Elwell +--- + drivers/char/broadcom/vcio.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/char/broadcom/vcio.c ++++ b/drivers/char/broadcom/vcio.c +@@ -18,6 +18,7 @@ + #include + #include + #include ++#include + #include + + #define MBOX_CHAN_PROPERTY 8 diff --git a/target/linux/bcm27xx/patches-5.10/950-0189-video-fbdev-bcm2708_fb-Use-common-compat-header.patch b/target/linux/bcm27xx/patches-5.10/950-0189-video-fbdev-bcm2708_fb-Use-common-compat-header.patch new file mode 100644 index 0000000000..6a4b9650c5 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0189-video-fbdev-bcm2708_fb-Use-common-compat-header.patch @@ -0,0 +1,23 @@ +From 6dd897b34471d95f9c01d19df06c339fe6fbf38c Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 2 Mar 2020 14:42:23 +0000 +Subject: [PATCH] video: fbdev: bcm2708_fb: Use common compat header + +The definition of compat_ptr is now common for most platforms, but +requires the inclusion of . + +Signed-off-by: Phil Elwell +--- + drivers/video/fbdev/bcm2708_fb.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/video/fbdev/bcm2708_fb.c ++++ b/drivers/video/fbdev/bcm2708_fb.c +@@ -38,6 +38,7 @@ + #include + #include + #include ++#include + + //#define BCM2708_FB_DEBUG + #define MODULE_NAME "bcm2708_fb" diff --git a/target/linux/bcm27xx/patches-5.10/950-0190-of-overlay-Correct-symbol-path-fixups.patch b/target/linux/bcm27xx/patches-5.10/950-0190-of-overlay-Correct-symbol-path-fixups.patch new file mode 100644 index 0000000000..cbbf4937f7 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0190-of-overlay-Correct-symbol-path-fixups.patch @@ -0,0 +1,37 @@ +From 68e9899b2c99dbe97ecf9008e7e43f5b393f26a3 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 6 Feb 2020 12:23:15 +0000 +Subject: [PATCH] of: overlay: Correct symbol path fixups + +When symbols from overlays are added to the live tree their paths must +be rebased. The translated symbol is normally the result of joining +the fragment-relative path (with a leading "/") to the target path +(either copied directly from the "target-path" property or resolved +from the phandle). This translation fails when the target is the root +node (a common case for Raspberry Pi overlays) because the resulting +path starts with a double slash. For example, if target-path is "/" and +the fragment adds a node called "newnode", the label associated with +that node will be assigned the path "//newnode", which can't be found +in the tree. + +Fix the failure case by explicitly replacing a target path of "/" with +an empty string. + +Fixes: d1651b03c2df ("of: overlay: add overlay symbols to live device tree") + +Signed-off-by: Phil Elwell +--- + drivers/of/overlay.c | 2 ++ + 1 file changed, 2 insertions(+) + +--- a/drivers/of/overlay.c ++++ b/drivers/of/overlay.c +@@ -245,6 +245,8 @@ static struct property *dup_and_fixup_sy + if (!target_path) + return NULL; + target_path_len = strlen(target_path); ++ if (!strcmp(target_path, "/")) ++ target_path_len = 0; + + new_prop = kzalloc(sizeof(*new_prop), GFP_KERNEL); + if (!new_prop) diff --git a/target/linux/bcm27xx/patches-5.10/950-0191-dt-bindings-pci-Add-DT-docs-for-Brcmstb-PCIe-device.patch b/target/linux/bcm27xx/patches-5.10/950-0191-dt-bindings-pci-Add-DT-docs-for-Brcmstb-PCIe-device.patch new file mode 100644 index 0000000000..566f08cbe3 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0191-dt-bindings-pci-Add-DT-docs-for-Brcmstb-PCIe-device.patch @@ -0,0 +1,77 @@ +From 4f65cebc14d6af8b4a9f19426b43b3ae49ee8538 Mon Sep 17 00:00:00 2001 +From: Jim Quinlan +Date: Mon, 15 Jan 2018 18:28:39 -0500 +Subject: [PATCH] dt-bindings: pci: Add DT docs for Brcmstb PCIe device + +The DT bindings description of the Brcmstb PCIe device is described. This +node can be used by almost all Broadcom settop box chips, using +ARM, ARM64, or MIPS CPU architectures. + +Signed-off-by: Jim Quinlan +--- + .../devicetree/bindings/pci/brcmstb-pcie.txt | 59 +++++++++++++++++++ + 1 file changed, 59 insertions(+) + create mode 100644 Documentation/devicetree/bindings/pci/brcmstb-pcie.txt + +--- /dev/null ++++ b/Documentation/devicetree/bindings/pci/brcmstb-pcie.txt +@@ -0,0 +1,59 @@ ++Brcmstb PCIe Host Controller Device Tree Bindings ++ ++Required Properties: ++- compatible ++ "brcm,bcm7425-pcie" -- for 7425 family MIPS-based SOCs. ++ "brcm,bcm7435-pcie" -- for 7435 family MIPS-based SOCs. ++ "brcm,bcm7445-pcie" -- for 7445 and later ARM based SOCs (not including ++ the 7278). ++ "brcm,bcm7278-pcie" -- for 7278 family ARM-based SOCs. ++ ++- reg -- the register start address and length for the PCIe reg block. ++- interrupts -- two interrupts are specified; the first interrupt is for ++ the PCI host controller and the second is for MSI if the built-in ++ MSI controller is to be used. ++- interrupt-names -- names of the interrupts (above): "pcie" and "msi". ++- #address-cells -- set to <3>. ++- #size-cells -- set to <2>. ++- #interrupt-cells: set to <1>. ++- interrupt-map-mask and interrupt-map, standard PCI properties to define the ++ mapping of the PCIe interface to interrupt numbers. ++- ranges: ranges for the PCI memory and I/O regions. ++- linux,pci-domain -- should be unique per host controller. ++ ++Optional Properties: ++- clocks -- phandle of pcie clock. ++- clock-names -- set to "sw_pcie" if clocks is used. ++- dma-ranges -- Specifies the inbound memory mapping regions when ++ an "identity map" is not possible. ++- msi-controller -- this property is typically specified to have the ++ PCIe controller use its internal MSI controller. ++- msi-parent -- set to use an external MSI interrupt controller. ++- brcm,enable-ssc -- (boolean) indicates usage of spread-spectrum clocking. ++- max-link-speed -- (integer) indicates desired generation of link: ++ 1 => 2.5 Gbps (gen1), 2 => 5.0 Gbps (gen2), 3 => 8.0 Gbps (gen3). ++ ++Example Node: ++ ++pcie0: pcie@f0460000 { ++ reg = <0x0 0xf0460000 0x0 0x9310>; ++ interrupts = <0x0 0x0 0x4>; ++ compatible = "brcm,bcm7445-pcie"; ++ #address-cells = <3>; ++ #size-cells = <2>; ++ ranges = <0x02000000 0x00000000 0x00000000 0x00000000 0xc0000000 0x00000000 0x08000000 ++ 0x02000000 0x00000000 0x08000000 0x00000000 0xc8000000 0x00000000 0x08000000>; ++ #interrupt-cells = <1>; ++ interrupt-map-mask = <0 0 0 7>; ++ interrupt-map = <0 0 0 1 &intc 0 47 3 ++ 0 0 0 2 &intc 0 48 3 ++ 0 0 0 3 &intc 0 49 3 ++ 0 0 0 4 &intc 0 50 3>; ++ clocks = <&sw_pcie0>; ++ clock-names = "sw_pcie"; ++ msi-parent = <&pcie0>; /* use PCIe's internal MSI controller */ ++ msi-controller; /* use PCIe's internal MSI controller */ ++ brcm,ssc; ++ max-link-speed = <1>; ++ linux,pci-domain = <0>; ++ }; diff --git a/target/linux/bcm27xx/patches-5.10/950-0192-Kbuild-Allow-.dtbo-overlays-to-be-built-adjust.patch b/target/linux/bcm27xx/patches-5.10/950-0192-Kbuild-Allow-.dtbo-overlays-to-be-built-adjust.patch new file mode 100644 index 0000000000..bf59fc6c8f --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0192-Kbuild-Allow-.dtbo-overlays-to-be-built-adjust.patch @@ -0,0 +1,26 @@ +From 45ae2035e05d4519d86f1073a257dea3a920f484 Mon Sep 17 00:00:00 2001 +From: Nataliya Korovkina +Date: Thu, 12 Mar 2020 17:22:53 -0400 +Subject: [PATCH] Kbuild: Allow .dtbo overlays to be built, adjust. + +This is adjustment to commit +d368ceaacdccd7732dc97d1d7987bdf7149d62e3 "kbuild: Allow .dtbo overlays to be built piecemeal" + +prepare3 target has gone from mainline tree in branch 5.4.y + +Signed-off-by: Nataliya Korovkina +--- + Makefile | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/Makefile ++++ b/Makefile +@@ -1354,7 +1354,7 @@ ifneq ($(dtstree),) + %.dtb: include/config/kernel.release scripts_dtc + $(Q)$(MAKE) $(build)=$(dtstree) $(dtstree)/$@ + +-%.dtbo: prepare3 scripts_dtc ++%.dtbo: include/config/kernel.release scripts_dtc + $(Q)$(MAKE) $(build)=$(dtstree) $(dtstree)/$@ + + PHONY += dtbs dtbs_install dtbs_check diff --git a/target/linux/bcm27xx/patches-5.10/950-0193-bcmgenet-Disable-skip_umac_reset-by-default.patch b/target/linux/bcm27xx/patches-5.10/950-0193-bcmgenet-Disable-skip_umac_reset-by-default.patch new file mode 100644 index 0000000000..9792ac8290 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0193-bcmgenet-Disable-skip_umac_reset-by-default.patch @@ -0,0 +1,23 @@ +From f290455548d9e9ea5f03464d229d08a854a9fb37 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Wed, 1 Apr 2020 11:22:44 +0100 +Subject: [PATCH] bcmgenet: Disable skip_umac_reset by default + +Possible fixed upstream by 'net: bcmgenet: keep MAC in reset until PHY is up' + +Signed-off-by: popcornmix +--- + drivers/net/ethernet/broadcom/genet/bcmgenet.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c ++++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c +@@ -67,7 +67,7 @@ + + /* Forward declarations */ + static void bcmgenet_set_rx_mode(struct net_device *dev); +-static bool skip_umac_reset = true; ++static bool skip_umac_reset = false; + module_param(skip_umac_reset, bool, 0444); + MODULE_PARM_DESC(skip_umac_reset, "Skip UMAC reset step"); + diff --git a/target/linux/bcm27xx/patches-5.10/950-0194-drm-fourcc-Add-packed-10bit-YUV-4-2-0-format.patch b/target/linux/bcm27xx/patches-5.10/950-0194-drm-fourcc-Add-packed-10bit-YUV-4-2-0-format.patch new file mode 100644 index 0000000000..c075dd1f9c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0194-drm-fourcc-Add-packed-10bit-YUV-4-2-0-format.patch @@ -0,0 +1,55 @@ +From 1a3319588434a2acfe47a38fcdf6583a3b84ecd3 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Fri, 24 Jan 2020 14:22:06 +0000 +Subject: [PATCH] drm/fourcc: Add packed 10bit YUV 4:2:0 format + +Adds a format that is 3 10bit YUV 4:2:0 samples packed into +a 32bit work (with 2 spare bits). + +Supported on Broadcom BCM2711 chips. + +Signed-off-by: Dave Stevenson +--- + drivers/gpu/drm/drm_fourcc.c | 3 +++ + include/uapi/drm/drm_fourcc.h | 11 +++++++++++ + 2 files changed, 14 insertions(+) + +--- a/drivers/gpu/drm/drm_fourcc.c ++++ b/drivers/gpu/drm/drm_fourcc.c +@@ -286,6 +286,9 @@ const struct drm_format_info *__drm_form + .num_planes = 3, .char_per_block = { 2, 2, 2 }, + .block_w = { 1, 1, 1 }, .block_h = { 1, 1, 1 }, .hsub = 0, + .vsub = 0, .is_yuv = true }, ++ { .format = DRM_FORMAT_P030, .depth = 0, .num_planes = 2, ++ .char_per_block = { 4, 4, 0 }, .block_w = { 3, 0, 0 }, .block_h = { 1, 0, 0 }, ++ .hsub = 2, .vsub = 2, .is_yuv = true}, + }; + + unsigned int i; +--- a/include/uapi/drm/drm_fourcc.h ++++ b/include/uapi/drm/drm_fourcc.h +@@ -288,6 +288,13 @@ extern "C" { + #define DRM_FORMAT_Q401 fourcc_code('Q', '4', '0', '1') + + /* ++ * 2 plane YCbCr MSB aligned, 3 pixels packed into 4 bytes. ++ * index 0 = Y plane, [31:0] x:Y2:Y1:Y0 2:10:10:10 little endian ++ * index 1 = Cr:Cb plane, [63:0] x:Cr2:Cb2:Cr1:x:Cb1:Cr0:Cb0 [2:10:10:10:2:10:10:10] little endian ++ */ ++#define DRM_FORMAT_P030 fourcc_code('P', '0', '3', '0') /* 2x2 subsampled Cr:Cb plane 10 bits per channel packed */ ++ ++/* + * 3 plane YCbCr + * index 0: Y plane, [7:0] Y + * index 1: Cb plane, [7:0] Cb +@@ -777,6 +784,10 @@ drm_fourcc_canonicalize_nvidia_format_mo + * and UV. Some SAND-using hardware stores UV in a separate tiled + * image from Y to reduce the column height, which is not supported + * with these modifiers. ++ * ++ * The DRM_FORMAT_MOD_BROADCOM_SAND128_COL_HEIGHT modifier is also ++ * supported for DRM_FORMAT_P030 where the columns remain as 128 bytes ++ * wide, but as this is a 10 bpp format that translates to 96 pixels. + */ + + #define DRM_FORMAT_MOD_BROADCOM_SAND32_COL_HEIGHT(v) \ diff --git a/target/linux/bcm27xx/patches-5.10/950-0195-media-uapi-hevc-Add-scaling-matrix-control.patch b/target/linux/bcm27xx/patches-5.10/950-0195-media-uapi-hevc-Add-scaling-matrix-control.patch new file mode 100644 index 0000000000..53e3f49914 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0195-media-uapi-hevc-Add-scaling-matrix-control.patch @@ -0,0 +1,150 @@ +From e4ae41f35d7d361759b5aa1e1a3e13bafd46f9db Mon Sep 17 00:00:00 2001 +From: Jernej Skrabec +Date: Fri, 13 Dec 2019 17:04:25 +0100 +Subject: [PATCH] media: uapi: hevc: Add scaling matrix control + +Taken from https://patchwork.linuxtv.org/patch/60728/ +Changes (mainly documentation) have been requested. + +HEVC has a scaling matrix concept. Add support for it. + +Signed-off-by: Jernej Skrabec +--- + .../media/v4l/ext-ctrls-codec.rst | 41 +++++++++++++++++++ + .../media/v4l/pixfmt-compressed.rst | 1 + + drivers/media/v4l2-core/v4l2-ctrls.c | 10 +++++ + include/media/hevc-ctrls.h | 11 +++++ + 4 files changed, 63 insertions(+) + +--- a/Documentation/userspace-api/media/v4l/ext-ctrls-codec.rst ++++ b/Documentation/userspace-api/media/v4l/ext-ctrls-codec.rst +@@ -4319,6 +4319,47 @@ enum v4l2_mpeg_video_hevc_size_of_length + - ``padding[6]`` + - Applications and drivers must set this to zero. + ++``V4L2_CID_MPEG_VIDEO_HEVC_SCALING_MATRIX (struct)`` ++ Specifies the scaling matrix (as extracted from the bitstream) for ++ the associated HEVC slice data. The bitstream parameters are ++ defined according to :ref:`hevc`, section 7.4.5 "Scaling list ++ data semantics". For further documentation, refer to the above ++ specification, unless there is an explicit comment stating ++ otherwise. ++ ++ .. note:: ++ ++ This compound control is not yet part of the public kernel API and ++ it is expected to change. ++ ++.. c:type:: v4l2_ctrl_hevc_scaling_matrix ++ ++.. cssclass:: longtable ++ ++.. flat-table:: struct v4l2_ctrl_hevc_scaling_matrix ++ :header-rows: 0 ++ :stub-columns: 0 ++ :widths: 1 1 2 ++ ++ * - __u8 ++ - ``scaling_list_4x4[6][16]`` ++ - ++ * - __u8 ++ - ``scaling_list_8x8[6][64]`` ++ - ++ * - __u8 ++ - ``scaling_list_16x16[6][64]`` ++ - ++ * - __u8 ++ - ``scaling_list_32x32[2][64]`` ++ - ++ * - __u8 ++ - ``scaling_list_dc_coef_16x16[6]`` ++ - ++ * - __u8 ++ - ``scaling_list_dc_coef_32x32[2]`` ++ - ++ + ``V4L2_CID_MPEG_VIDEO_HEVC_DECODE_MODE (enum)`` + Specifies the decoding mode to use. Currently exposes slice-based and + frame-based decoding but new modes might be added later on. +--- a/Documentation/userspace-api/media/v4l/pixfmt-compressed.rst ++++ b/Documentation/userspace-api/media/v4l/pixfmt-compressed.rst +@@ -200,6 +200,7 @@ Compressed Formats + * ``V4L2_CID_MPEG_VIDEO_HEVC_SPS`` + * ``V4L2_CID_MPEG_VIDEO_HEVC_PPS`` + * ``V4L2_CID_MPEG_VIDEO_HEVC_SLICE_PARAMS`` ++ * ``V4L2_CID_MPEG_VIDEO_HEVC_SCALING_MATRIX`` + See the :ref:`associated Codec Control IDs `. + Buffers associated with this pixel format must contain the appropriate + number of macroblocks to decode a full corresponding frame. +--- a/drivers/media/v4l2-core/v4l2-ctrls.c ++++ b/drivers/media/v4l2-core/v4l2-ctrls.c +@@ -1022,6 +1022,7 @@ const char *v4l2_ctrl_get_name(u32 id) + case V4L2_CID_MPEG_VIDEO_HEVC_SPS: return "HEVC Sequence Parameter Set"; + case V4L2_CID_MPEG_VIDEO_HEVC_PPS: return "HEVC Picture Parameter Set"; + case V4L2_CID_MPEG_VIDEO_HEVC_SLICE_PARAMS: return "HEVC Slice Parameters"; ++ case V4L2_CID_MPEG_VIDEO_HEVC_SCALING_MATRIX: return "HEVC Scaling Matrix"; + case V4L2_CID_MPEG_VIDEO_HEVC_DECODE_MODE: return "HEVC Decode Mode"; + case V4L2_CID_MPEG_VIDEO_HEVC_START_CODE: return "HEVC Start Code"; + +@@ -1462,6 +1463,9 @@ void v4l2_ctrl_fill(u32 id, const char * + case V4L2_CID_MPEG_VIDEO_HEVC_SLICE_PARAMS: + *type = V4L2_CTRL_TYPE_HEVC_SLICE_PARAMS; + break; ++ case V4L2_CID_MPEG_VIDEO_HEVC_SCALING_MATRIX: ++ *type = V4L2_CTRL_TYPE_HEVC_SCALING_MATRIX; ++ break; + case V4L2_CID_UNIT_CELL_SIZE: + *type = V4L2_CTRL_TYPE_AREA; + *flags |= V4L2_CTRL_FLAG_READ_ONLY; +@@ -1935,6 +1939,9 @@ static int std_validate_compound(const s + zero_padding(*p_hevc_slice_params); + break; + ++ case V4L2_CTRL_TYPE_HEVC_SCALING_MATRIX: ++ break; ++ + case V4L2_CTRL_TYPE_AREA: + area = p; + if (!area->width || !area->height) +@@ -2645,6 +2652,9 @@ static struct v4l2_ctrl *v4l2_ctrl_new(s + case V4L2_CTRL_TYPE_HEVC_SLICE_PARAMS: + elem_size = sizeof(struct v4l2_ctrl_hevc_slice_params); + break; ++ case V4L2_CTRL_TYPE_HEVC_SCALING_MATRIX: ++ elem_size = sizeof(struct v4l2_ctrl_hevc_scaling_matrix); ++ break; + case V4L2_CTRL_TYPE_AREA: + elem_size = sizeof(struct v4l2_area); + break; +--- a/include/media/hevc-ctrls.h ++++ b/include/media/hevc-ctrls.h +@@ -19,6 +19,7 @@ + #define V4L2_CID_MPEG_VIDEO_HEVC_SPS (V4L2_CID_MPEG_BASE + 1008) + #define V4L2_CID_MPEG_VIDEO_HEVC_PPS (V4L2_CID_MPEG_BASE + 1009) + #define V4L2_CID_MPEG_VIDEO_HEVC_SLICE_PARAMS (V4L2_CID_MPEG_BASE + 1010) ++#define V4L2_CID_MPEG_VIDEO_HEVC_SCALING_MATRIX (V4L2_CID_MPEG_BASE + 1011) + #define V4L2_CID_MPEG_VIDEO_HEVC_DECODE_MODE (V4L2_CID_MPEG_BASE + 1015) + #define V4L2_CID_MPEG_VIDEO_HEVC_START_CODE (V4L2_CID_MPEG_BASE + 1016) + +@@ -26,6 +27,7 @@ + #define V4L2_CTRL_TYPE_HEVC_SPS 0x0120 + #define V4L2_CTRL_TYPE_HEVC_PPS 0x0121 + #define V4L2_CTRL_TYPE_HEVC_SLICE_PARAMS 0x0122 ++#define V4L2_CTRL_TYPE_HEVC_SCALING_MATRIX 0x0123 + + enum v4l2_mpeg_video_hevc_decode_mode { + V4L2_MPEG_VIDEO_HEVC_DECODE_MODE_SLICE_BASED, +@@ -210,4 +212,13 @@ struct v4l2_ctrl_hevc_slice_params { + __u64 flags; + }; + ++struct v4l2_ctrl_hevc_scaling_matrix { ++ __u8 scaling_list_4x4[6][16]; ++ __u8 scaling_list_8x8[6][64]; ++ __u8 scaling_list_16x16[6][64]; ++ __u8 scaling_list_32x32[2][64]; ++ __u8 scaling_list_dc_coef_16x16[6]; ++ __u8 scaling_list_dc_coef_32x32[2]; ++}; ++ + #endif diff --git a/target/linux/bcm27xx/patches-5.10/950-0196-media-uapi-hevc-Add-segment-address-field.patch b/target/linux/bcm27xx/patches-5.10/950-0196-media-uapi-hevc-Add-segment-address-field.patch new file mode 100644 index 0000000000..b0e610bf04 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0196-media-uapi-hevc-Add-segment-address-field.patch @@ -0,0 +1,61 @@ +From 551676b89a12d9de33618c1c02b749653941fe83 Mon Sep 17 00:00:00 2001 +From: Jernej Skrabec +Date: Fri, 13 Dec 2019 17:04:27 +0100 +Subject: [PATCH] media: uapi: hevc: Add segment address field + +From https://patchwork.linuxtv.org/patch/60725/ +Changes requested, but mainly docs. + +If HEVC frame consists of multiple slices, segment address has to be +known in order to properly decode it. + +Add segment address field to slice parameters. + +Signed-off-by: Jernej Skrabec +--- + Documentation/userspace-api/media/v4l/ext-ctrls-codec.rst | 5 ++++- + include/media/hevc-ctrls.h | 5 ++++- + 2 files changed, 8 insertions(+), 2 deletions(-) + +--- a/Documentation/userspace-api/media/v4l/ext-ctrls-codec.rst ++++ b/Documentation/userspace-api/media/v4l/ext-ctrls-codec.rst +@@ -4111,6 +4111,9 @@ enum v4l2_mpeg_video_hevc_size_of_length + * - __u32 + - ``data_bit_offset`` + - Offset (in bits) to the video data in the current slice data. ++ * - __u32 ++ - ``slice_segment_addr`` ++ - + * - __u8 + - ``nal_unit_type`` + - +@@ -4188,7 +4191,7 @@ enum v4l2_mpeg_video_hevc_size_of_length + - ``num_rps_poc_lt_curr`` + - The number of reference pictures in the long-term set. + * - __u8 +- - ``padding[7]`` ++ - ``padding[5]`` + - Applications and drivers must set this to zero. + * - struct :c:type:`v4l2_hevc_dpb_entry` + - ``dpb[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]`` +--- a/include/media/hevc-ctrls.h ++++ b/include/media/hevc-ctrls.h +@@ -168,6 +168,9 @@ struct v4l2_ctrl_hevc_slice_params { + __u32 bit_size; + __u32 data_bit_offset; + ++ /* ISO/IEC 23008-2, ITU-T Rec. H.265: General slice segment header */ ++ __u32 slice_segment_addr; ++ + /* ISO/IEC 23008-2, ITU-T Rec. H.265: NAL unit header */ + __u8 nal_unit_type; + __u8 nuh_temporal_id_plus1; +@@ -201,7 +204,7 @@ struct v4l2_ctrl_hevc_slice_params { + __u8 num_rps_poc_st_curr_after; + __u8 num_rps_poc_lt_curr; + +- __u8 padding; ++ __u8 padding[5]; + + /* ISO/IEC 23008-2, ITU-T Rec. H.265: General slice segment header */ + struct v4l2_hevc_dpb_entry dpb[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]; diff --git a/target/linux/bcm27xx/patches-5.10/950-0197-media-uapi-Add-hevc-ctrls-for-WPP-decoding.patch b/target/linux/bcm27xx/patches-5.10/950-0197-media-uapi-Add-hevc-ctrls-for-WPP-decoding.patch new file mode 100644 index 0000000000..a018a1ba47 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0197-media-uapi-Add-hevc-ctrls-for-WPP-decoding.patch @@ -0,0 +1,40 @@ +From cfbd02c5469513b6d28d9012b14d70baa44869c5 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Mon, 23 Mar 2020 19:00:17 +0000 +Subject: [PATCH] media: uapi: Add hevc ctrls for WPP decoding + +WPP can allow greater parallelism within the decode, but needs +offset information to be passed in. + +Adds num_entry_point_offsets and entry_point_offset_minus1 to +v4l2_ctrl_hevc_slice_params. + +This is based on Jernej Skrabec's patches for cedrus which +implement the same feature. + +Signed-off-by: Dave Stevenson +--- + include/media/hevc-ctrls.h | 5 ++++- + 1 file changed, 4 insertions(+), 1 deletion(-) + +--- a/include/media/hevc-ctrls.h ++++ b/include/media/hevc-ctrls.h +@@ -170,6 +170,7 @@ struct v4l2_ctrl_hevc_slice_params { + + /* ISO/IEC 23008-2, ITU-T Rec. H.265: General slice segment header */ + __u32 slice_segment_addr; ++ __u32 num_entry_point_offsets; + + /* ISO/IEC 23008-2, ITU-T Rec. H.265: NAL unit header */ + __u8 nal_unit_type; +@@ -204,7 +205,9 @@ struct v4l2_ctrl_hevc_slice_params { + __u8 num_rps_poc_st_curr_after; + __u8 num_rps_poc_lt_curr; + +- __u8 padding[5]; ++ __u8 padding; ++ ++ __u32 entry_point_offset_minus1[256]; + + /* ISO/IEC 23008-2, ITU-T Rec. H.265: General slice segment header */ + struct v4l2_hevc_dpb_entry dpb[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]; diff --git a/target/linux/bcm27xx/patches-5.10/950-0198-media-videodev2.h-Add-a-format-for-column-YUV4-2-0-m.patch b/target/linux/bcm27xx/patches-5.10/950-0198-media-videodev2.h-Add-a-format-for-column-YUV4-2-0-m.patch new file mode 100644 index 0000000000..abeddf9c76 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0198-media-videodev2.h-Add-a-format-for-column-YUV4-2-0-m.patch @@ -0,0 +1,302 @@ +From 3e25101dea3ed13e98339dffbc9410459e617d9a Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Fri, 24 Jan 2020 14:28:21 +0000 +Subject: [PATCH] media: videodev2.h: Add a format for column YUV4:2:0 + modes + +Some of the Broadcom codec blocks use a column based YUV4:2:0 image +format, so add the documentation and defines for both 8 and 10 bit +versions. + +Signed-off-by: Dave Stevenson +--- + .../media/v4l/pixfmt-nv12-col128.rst | 215 ++++++++++++++++++ + .../userspace-api/media/v4l/pixfmt-nv12.rst | 14 +- + .../userspace-api/media/v4l/yuv-formats.rst | 1 + + drivers/media/v4l2-core/v4l2-ioctl.c | 2 + + include/uapi/linux/videodev2.h | 4 + + 5 files changed, 233 insertions(+), 3 deletions(-) + create mode 100644 Documentation/userspace-api/media/v4l/pixfmt-nv12-col128.rst + +--- /dev/null ++++ b/Documentation/userspace-api/media/v4l/pixfmt-nv12-col128.rst +@@ -0,0 +1,215 @@ ++.. Permission is granted to copy, distribute and/or modify this ++.. document under the terms of the GNU Free Documentation License, ++.. Version 1.1 or any later version published by the Free Software ++.. Foundation, with no Invariant Sections, no Front-Cover Texts ++.. and no Back-Cover Texts. A copy of the license is included at ++.. Documentation/media/uapi/fdl-appendix.rst. ++.. ++.. TODO: replace it to GFDL-1.1-or-later WITH no-invariant-sections ++ ++.. _V4L2_PIX_FMT_NV12_COL128: ++.. _V4L2_PIX_FMT_NV12_10_COL128: ++ ++******************************************************************************** ++V4L2_PIX_FMT_NV12_COL128, V4L2_PIX_FMT_NV12_10_COL128 ++******************************************************************************** ++ ++ ++V4L2_PIX_FMT_NV21_COL128 ++Formats with ½ horizontal and vertical chroma resolution. This format ++has two planes - one for luminance and one for chrominance. Chroma ++samples are interleaved. The difference to ``V4L2_PIX_FMT_NV12`` is the ++memory layout. The image is split into columns of 128 bytes wide rather than ++being in raster order. ++ ++V4L2_PIX_FMT_NV12_10_COL128 ++Follows the same pattern as ``V4L2_PIX_FMT_NV21_COL128`` with 128 byte, but is ++a 10bit format with 3 10-bit samples being packed into 4 bytes. Each 128 byte ++wide column therefore contains 96 samples. ++ ++ ++Description ++=========== ++ ++This is the two-plane versions of the YUV 4:2:0 format where data is ++grouped into 128 byte wide columns. The three components are separated into ++two sub-images or planes. The Y plane has one byte per pixel and pixels ++are grouped into 128 byte wide columns. The CbCr plane has the same width, ++in bytes, as the Y plane (and the image), but is half as tall in pixels. ++The chroma plane is also in 128 byte columns, reflecting 64 Cb and 64 Cr ++samples. ++ ++The chroma samples for a column follow the luma samples. If there is any ++paddding, then that will be reflected via the selection API. ++The luma height must be a multiple of 2 lines. ++ ++The normal bytesperline is effectively fixed at 128. However the format ++requires knowledge of the stride between columns, therefore the bytesperline ++value has been repurposed to denote the number of 128 byte long lines between ++the start of each column. ++ ++**Byte Order.** ++ ++ ++.. flat-table:: ++ :header-rows: 0 ++ :stub-columns: 0 ++ :widths: 12 12 12 12 12 4 12 12 12 12 ++ ++ * - start + 0: ++ - Y'\ :sub:`0,0` ++ - Y'\ :sub:`0,1` ++ - Y'\ :sub:`0,2` ++ - Y'\ :sub:`0,3` ++ - ... ++ - Y'\ :sub:`0,124` ++ - Y'\ :sub:`0,125` ++ - Y'\ :sub:`0,126` ++ - Y'\ :sub:`0,127` ++ * - start + 128: ++ - Y'\ :sub:`1,0` ++ - Y'\ :sub:`1,1` ++ - Y'\ :sub:`1,2` ++ - Y'\ :sub:`1,3` ++ - ... ++ - Y'\ :sub:`1,124` ++ - Y'\ :sub:`1,125` ++ - Y'\ :sub:`1,126` ++ - Y'\ :sub:`1,127` ++ * - start + 256: ++ - Y'\ :sub:`2,0` ++ - Y'\ :sub:`2,1` ++ - Y'\ :sub:`2,2` ++ - Y'\ :sub:`2,3` ++ - ... ++ - Y'\ :sub:`2,124` ++ - Y'\ :sub:`2,125` ++ - Y'\ :sub:`2,126` ++ - Y'\ :sub:`2,127` ++ * - ... ++ - ... ++ - ... ++ - ... ++ - ... ++ - ... ++ - ... ++ - ... ++ * - start + ((height-1) * 128): ++ - Y'\ :sub:`height-1,0` ++ - Y'\ :sub:`height-1,1` ++ - Y'\ :sub:`height-1,2` ++ - Y'\ :sub:`height-1,3` ++ - ... ++ - Y'\ :sub:`height-1,124` ++ - Y'\ :sub:`height-1,125` ++ - Y'\ :sub:`height-1,126` ++ - Y'\ :sub:`height-1,127` ++ * - start + ((height) * 128): ++ - Cb\ :sub:`0,0` ++ - Cr\ :sub:`0,0` ++ - Cb\ :sub:`0,1` ++ - Cr\ :sub:`0,1` ++ - ... ++ - Cb\ :sub:`0,62` ++ - Cr\ :sub:`0,62` ++ - Cb\ :sub:`0,63` ++ - Cr\ :sub:`0,63` ++ * - start + ((height+1) * 128): ++ - Cb\ :sub:`1,0` ++ - Cr\ :sub:`1,0` ++ - Cb\ :sub:`1,1` ++ - Cr\ :sub:`1,1` ++ - ... ++ - Cb\ :sub:`1,62` ++ - Cr\ :sub:`1,62` ++ - Cb\ :sub:`1,63` ++ - Cr\ :sub:`1,63` ++ * - ... ++ - ... ++ - ... ++ - ... ++ - ... ++ - ... ++ - ... ++ - ... ++ * - start + ((height+(height/2)-1) * 128): ++ - Cb\ :sub:`(height/2)-1,0` ++ - Cr\ :sub:`(height/2)-1,0` ++ - Cb\ :sub:`(height/2)-1,1` ++ - Cr\ :sub:`(height/2)-1,1` ++ - ... ++ - Cb\ :sub:`(height/2)-1,62` ++ - Cr\ :sub:`(height/2)-1,62` ++ - Cb\ :sub:`(height/2)-1,63` ++ - Cr\ :sub:`(height/2)-1,63` ++ * - start + (bytesperline * 128): ++ - Y'\ :sub:`0,128` ++ - Y'\ :sub:`0,129` ++ - Y'\ :sub:`0,130` ++ - Y'\ :sub:`0,131` ++ - ... ++ - Y'\ :sub:`0,252` ++ - Y'\ :sub:`0,253` ++ - Y'\ :sub:`0,254` ++ - Y'\ :sub:`0,255` ++ * - ... ++ - ... ++ - ... ++ - ... ++ - ... ++ - ... ++ - ... ++ - ... ++ ++V4L2_PIX_FMT_NV12_10_COL128 uses the same 128 byte column structure, but ++encodes 10-bit YUV. ++3 10-bit values are packed into 4 bytes as bits 9:0, 19:10, and 29:20, with ++bits 30 & 31 unused. For the luma plane, bits 9:0 are Y0, 19:10 are Y1, and ++29:20 are Y2. For the chroma plane the samples always come in pairs of Cr ++and Cb, so it needs to be considered 6 values packed in 8 bytes. ++ ++Bit-packed representation. ++ ++.. raw:: latex ++ ++ \small ++ ++.. tabularcolumns:: |p{1.2cm}||p{1.2cm}||p{1.2cm}||p{1.2cm}|p{3.2cm}|p{3.2cm}| ++ ++.. flat-table:: ++ :header-rows: 0 ++ :stub-columns: 0 ++ :widths: 8 8 8 8 ++ ++ * - Y'\ :sub:`00[7:0]` ++ - Y'\ :sub:`01[5:0] (bits 7--2)` Y'\ :sub:`00[9:8]`\ (bits 1--0) ++ - Y'\ :sub:`02[3:0] (bits 7--4)` Y'\ :sub:`01[9:6]`\ (bits 3--0) ++ - unused (bits 7--6)` Y'\ :sub:`02[9:4]`\ (bits 5--0) ++ ++.. raw:: latex ++ ++ \small ++ ++.. tabularcolumns:: |p{1.2cm}||p{1.2cm}||p{1.2cm}||p{1.2cm}|p{3.2cm}|p{3.2cm}| ++ ++.. flat-table:: ++ :header-rows: 0 ++ :stub-columns: 0 ++ :widths: 12 12 12 12 12 12 12 12 ++ ++ * - Cb\ :sub:`00[7:0]` ++ - Cr\ :sub:`00[5:0]`\ (bits 7--2) Cb\ :sub:`00[9:8]`\ (bits 1--0) ++ - Cb\ :sub:`01[3:0]`\ (bits 7--4) Cr\ :sub:`00[9:6]`\ (bits 3--0) ++ - unused (bits 7--6) Cb\ :sub:`02[9:4]`\ (bits 5--0) ++ - Cr\ :sub:`01[7:0]` ++ - Cb\ :sub:`02[5:0]`\ (bits 7--2) Cr\ :sub:`01[9:8]`\ (bits 1--0) ++ - Cr\ :sub:`02[3:0]`\ (bits 7--4) Cb\ :sub:`02[9:6]`\ (bits 3--0) ++ - unused (bits 7--6) Cr\ :sub:`02[9:4]`\ (bits 5--0) ++ ++.. raw:: latex ++ ++ \normalsize ++ ++ ++ ++ +--- a/Documentation/userspace-api/media/v4l/pixfmt-nv12.rst ++++ b/Documentation/userspace-api/media/v4l/pixfmt-nv12.rst +@@ -3,9 +3,9 @@ + .. _V4L2-PIX-FMT-NV12: + .. _V4L2-PIX-FMT-NV21: + +-****************************************************** +-V4L2_PIX_FMT_NV12 ('NV12'), V4L2_PIX_FMT_NV21 ('NV21') +-****************************************************** ++******************************************************************************** ++V4L2_PIX_FMT_NV12 ('NV12'), V4L2_PIX_FMT_NV21 ('NV21'), V4L2_PIX_FMT_NV12_COL128 ++******************************************************************************** + + + V4L2_PIX_FMT_NV21 +@@ -31,6 +31,14 @@ with a Cr byte. + If the Y plane has pad bytes after each row, then the CbCr plane has as + many pad bytes after its rows. + ++``V4L2_PIX_FMT_NV12_COL128`` is the tiled version of ++``V4L2_PIX_FMT_NV12`` with the image broken down into 128 pixel wide columns of ++Y followed by the associated combined CbCr plane. ++The normal bytesperline is effectively fixed at 128. However the format ++requires knowledge of the stride between columns, therefore the bytesperline ++value has been repurposed to denote the number of 128 byte long lines between ++the start of each column. ++ + **Byte Order.** + Each cell is one byte. + +--- a/Documentation/userspace-api/media/v4l/yuv-formats.rst ++++ b/Documentation/userspace-api/media/v4l/yuv-formats.rst +@@ -51,6 +51,7 @@ to brightness information. + pixfmt-nv12 + pixfmt-nv12m + pixfmt-nv12mt ++ pixfmt-nv12-col128 + pixfmt-nv16 + pixfmt-nv16m + pixfmt-nv24 +--- a/drivers/media/v4l2-core/v4l2-ioctl.c ++++ b/drivers/media/v4l2-core/v4l2-ioctl.c +@@ -1325,6 +1325,8 @@ static void v4l_fill_fmtdesc(struct v4l2 + case V4L2_PIX_FMT_NV61M: descr = "Y/CrCb 4:2:2 (N-C)"; break; + case V4L2_PIX_FMT_NV12MT: descr = "Y/CbCr 4:2:0 (64x32 MB, N-C)"; break; + case V4L2_PIX_FMT_NV12MT_16X16: descr = "Y/CbCr 4:2:0 (16x16 MB, N-C)"; break; ++ case V4L2_PIX_FMT_NV12_COL128: descr = "Y/CbCr 4:2:0 (128b cols)"; break; ++ case V4L2_PIX_FMT_NV12_10_COL128: descr = "10-bit Y/CbCr 4:2:0 (128b cols)"; break; + case V4L2_PIX_FMT_YUV420M: descr = "Planar YUV 4:2:0 (N-C)"; break; + case V4L2_PIX_FMT_YVU420M: descr = "Planar YVU 4:2:0 (N-C)"; break; + case V4L2_PIX_FMT_YUV422M: descr = "Planar YUV 4:2:2 (N-C)"; break; +--- a/include/uapi/linux/videodev2.h ++++ b/include/uapi/linux/videodev2.h +@@ -745,6 +745,10 @@ struct v4l2_pix_format { + #define V4L2_PIX_FMT_INZI v4l2_fourcc('I', 'N', 'Z', 'I') /* Intel Planar Greyscale 10-bit and Depth 16-bit */ + #define V4L2_PIX_FMT_SUNXI_TILED_NV12 v4l2_fourcc('S', 'T', '1', '2') /* Sunxi Tiled NV12 Format */ + #define V4L2_PIX_FMT_CNF4 v4l2_fourcc('C', 'N', 'F', '4') /* Intel 4-bit packed depth confidence information */ ++#define V4L2_PIX_FMT_NV12_COL128 v4l2_fourcc('N', 'C', '1', '2') /* 12 Y/CbCr 4:2:0 128 pixel wide column */ ++#define V4L2_PIX_FMT_NV12_10_COL128 v4l2_fourcc('N', 'C', '3', '0') ++ /* Y/CbCr 4:2:0 10bpc, 3x10 packed as 4 bytes in ++ * a 128 bytes / 96 pixel wide column */ + + /* 10bit raw bayer packed, 32 bytes for every 25 pixels, last LSB 6 bits unused */ + #define V4L2_PIX_FMT_IPU3_SBGGR10 v4l2_fourcc('i', 'p', '3', 'b') /* IPU3 packed 10-bit BGGR bayer */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0199-media-dt-bindings-media-Add-binding-for-the-Raspberr.patch b/target/linux/bcm27xx/patches-5.10/950-0199-media-dt-bindings-media-Add-binding-for-the-Raspberr.patch new file mode 100644 index 0000000000..c7bd718cfc --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0199-media-dt-bindings-media-Add-binding-for-the-Raspberr.patch @@ -0,0 +1,106 @@ +From 9b6a40e7b71b4f133e1151313b38ba187764a9e9 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 17 Mar 2020 10:53:16 +0000 +Subject: [PATCH] media: dt-bindings: media: Add binding for the + Raspberry PI HEVC decoder + +Adds a binding for the HEVC decoder found on the BCM2711 / Raspberry Pi 4. + +Signed-off-by: Dave Stevenson +--- + .../bindings/media/rpivid_hevc.yaml | 72 +++++++++++++++++++ + MAINTAINERS | 7 ++ + 2 files changed, 79 insertions(+) + create mode 100644 Documentation/devicetree/bindings/media/rpivid_hevc.yaml + +--- /dev/null ++++ b/Documentation/devicetree/bindings/media/rpivid_hevc.yaml +@@ -0,0 +1,72 @@ ++# SPDX-License-Identifier: GPL-2.0-only ++%YAML 1.2 ++--- ++$id: http://devicetree.org/schemas/media/rpivid_hevc.yaml# ++$schema: http://devicetree.org/meta-schemas/core.yaml# ++ ++title: Raspberry Pi HEVC Decoder ++ ++maintainers: ++ - Raspberry Pi ++ ++description: |- ++ The Camera Adaptation Layer (CAL) is a key component for image capture ++ applications. The capture module provides the system interface and the ++ processing capability to connect CSI2 image-sensor modules to the ++ DRA72x device. ++ ++properties: ++ compatible: ++ enum: ++ - raspberrypi,rpivid-vid-decoder ++ ++ reg: ++ minItems: 2 ++ items: ++ - description: The HEVC main register region ++ - description: The Interrupt controller register region ++ ++ reg-names: ++ minItems: 2 ++ items: ++ - const: hevc ++ - const: intc ++ ++ interrupts: ++ maxItems: 1 ++ ++ clocks: ++ items: ++ - description: The HEVC block clock ++ ++ clock-names: ++ items: ++ - const: hevc ++ ++required: ++ - compatible ++ - reg ++ - reg-names ++ - interrupts ++ - clocks ++ ++additionalProperties: false ++ ++examples: ++ - | ++ #include ++ ++ video-codec@7eb10000 { ++ compatible = "raspberrypi,rpivid-vid-decoder"; ++ reg = <0x0 0x7eb10000 0x1000>, /* INTC */ ++ <0x0 0x7eb00000 0x10000>; /* HEVC */ ++ reg-names = "intc", ++ "hevc"; ++ ++ interrupts = ; ++ ++ clocks = <&clk 0>; ++ clock-names = "hevc"; ++ }; ++ ++... +--- a/MAINTAINERS ++++ b/MAINTAINERS +@@ -3417,6 +3417,13 @@ N: bcm113* + N: bcm216* + N: kona + ++BROADCOM BCM2711 HEVC DECODER ++M: Raspberry Pi Kernel Maintenance ++L: linux-media@vger.kernel.org ++S: Maintained ++F: Documentation/devicetree/bindings/media/rpivid_hevc.jaml ++F: drivers/staging/media/rpivid ++ + BROADCOM BCM2835 CAMERA DRIVER + M: Dave Stevenson + L: linux-media@vger.kernel.org diff --git a/target/linux/bcm27xx/patches-5.10/950-0200-staging-media-Add-Raspberry-Pi-V4L2-H265-decoder.patch b/target/linux/bcm27xx/patches-5.10/950-0200-staging-media-Add-Raspberry-Pi-V4L2-H265-decoder.patch new file mode 100644 index 0000000000..491c0b8c43 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0200-staging-media-Add-Raspberry-Pi-V4L2-H265-decoder.patch @@ -0,0 +1,4341 @@ +From ea6d2c1bdad5a18f0d81ed4923a62f01180e3250 Mon Sep 17 00:00:00 2001 +From: John Cox +Date: Thu, 5 Mar 2020 18:30:41 +0000 +Subject: [PATCH] staging: media: Add Raspberry Pi V4L2 H265 decoder + +This driver is for the HEVC/H265 decoder block on the Raspberry +Pi 4, and conforms to the V4L2 stateless decoder API. + +Signed-off-by: John Cox +--- + drivers/staging/media/Kconfig | 2 + + drivers/staging/media/Makefile | 1 + + drivers/staging/media/rpivid/Kconfig | 16 + + drivers/staging/media/rpivid/Makefile | 5 + + drivers/staging/media/rpivid/rpivid.c | 432 ++++ + drivers/staging/media/rpivid/rpivid.h | 181 ++ + drivers/staging/media/rpivid/rpivid_dec.c | 79 + + drivers/staging/media/rpivid/rpivid_dec.h | 19 + + drivers/staging/media/rpivid/rpivid_h265.c | 2275 +++++++++++++++++++ + drivers/staging/media/rpivid/rpivid_hw.c | 321 +++ + drivers/staging/media/rpivid/rpivid_hw.h | 300 +++ + drivers/staging/media/rpivid/rpivid_video.c | 593 +++++ + drivers/staging/media/rpivid/rpivid_video.h | 30 + + 13 files changed, 4254 insertions(+) + create mode 100644 drivers/staging/media/rpivid/Kconfig + create mode 100644 drivers/staging/media/rpivid/Makefile + create mode 100644 drivers/staging/media/rpivid/rpivid.c + create mode 100644 drivers/staging/media/rpivid/rpivid.h + create mode 100644 drivers/staging/media/rpivid/rpivid_dec.c + create mode 100644 drivers/staging/media/rpivid/rpivid_dec.h + create mode 100644 drivers/staging/media/rpivid/rpivid_h265.c + create mode 100644 drivers/staging/media/rpivid/rpivid_hw.c + create mode 100644 drivers/staging/media/rpivid/rpivid_hw.h + create mode 100644 drivers/staging/media/rpivid/rpivid_video.c + create mode 100644 drivers/staging/media/rpivid/rpivid_video.h + +--- a/drivers/staging/media/Kconfig ++++ b/drivers/staging/media/Kconfig +@@ -34,6 +34,8 @@ source "drivers/staging/media/omap4iss/K + + source "drivers/staging/media/rkvdec/Kconfig" + ++source "drivers/staging/media/rpivid/Kconfig" ++ + source "drivers/staging/media/sunxi/Kconfig" + + source "drivers/staging/media/tegra-vde/Kconfig" +--- a/drivers/staging/media/Makefile ++++ b/drivers/staging/media/Makefile +@@ -5,6 +5,7 @@ obj-$(CONFIG_VIDEO_IMX_MEDIA) += imx/ + obj-$(CONFIG_VIDEO_MESON_VDEC) += meson/vdec/ + obj-$(CONFIG_VIDEO_OMAP4) += omap4iss/ + obj-$(CONFIG_VIDEO_ROCKCHIP_VDEC) += rkvdec/ ++obj-$(CONFIG_VIDEO_RPIVID) += rpivid/ + obj-$(CONFIG_VIDEO_SUNXI) += sunxi/ + obj-$(CONFIG_VIDEO_TEGRA) += tegra-video/ + obj-$(CONFIG_TEGRA_VDE) += tegra-vde/ +--- /dev/null ++++ b/drivers/staging/media/rpivid/Kconfig +@@ -0,0 +1,16 @@ ++# SPDX-License-Identifier: GPL-2.0 ++ ++config VIDEO_RPIVID ++ tristate "Rpi H265 driver" ++ depends on VIDEO_DEV && VIDEO_V4L2 ++ depends on MEDIA_CONTROLLER ++ depends on OF ++ depends on MEDIA_CONTROLLER_REQUEST_API ++ select VIDEOBUF2_DMA_CONTIG ++ select V4L2_MEM2MEM_DEV ++ help ++ Support for the Rpi H265 h/w decoder. ++ ++ To compile this driver as a module, choose M here: the module ++ will be called rpivid-hevc. ++ +--- /dev/null ++++ b/drivers/staging/media/rpivid/Makefile +@@ -0,0 +1,5 @@ ++# SPDX-License-Identifier: GPL-2.0 ++obj-$(CONFIG_VIDEO_RPIVID) += rpivid-hevc.o ++ ++rpivid-hevc-y = rpivid.o rpivid_video.o rpivid_dec.o \ ++ rpivid_hw.o rpivid_h265.o +--- /dev/null ++++ b/drivers/staging/media/rpivid/rpivid.c +@@ -0,0 +1,432 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * Raspberry Pi HEVC driver ++ * ++ * Copyright (C) 2020 Raspberry Pi (Trading) Ltd ++ * ++ * Based on the Cedrus VPU driver, that is: ++ * ++ * Copyright (C) 2016 Florent Revest ++ * Copyright (C) 2018 Paul Kocialkowski ++ * Copyright (C) 2018 Bootlin ++ */ ++ ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++#include "rpivid.h" ++#include "rpivid_video.h" ++#include "rpivid_hw.h" ++#include "rpivid_dec.h" ++ ++/* ++ * Default /dev/videoN node number. ++ * Deliberately avoid the very low numbers as these are often taken by webcams ++ * etc, and simple apps tend to only go for /dev/video0. ++ */ ++static int video_nr = 19; ++module_param(video_nr, int, 0644); ++MODULE_PARM_DESC(video_nr, "decoder video device number"); ++ ++static const struct rpivid_control rpivid_ctrls[] = { ++ { ++ .cfg = { ++ .id = V4L2_CID_MPEG_VIDEO_HEVC_SPS, ++ }, ++ .required = true, ++ }, ++ { ++ .cfg = { ++ .id = V4L2_CID_MPEG_VIDEO_HEVC_PPS, ++ }, ++ .required = true, ++ }, ++ { ++ .cfg = { ++ .id = V4L2_CID_MPEG_VIDEO_HEVC_SCALING_MATRIX, ++ }, ++ .required = false, ++ }, ++ { ++ .cfg = { ++ .id = V4L2_CID_MPEG_VIDEO_HEVC_SLICE_PARAMS, ++ }, ++ .required = true, ++ }, ++ { ++ .cfg = { ++ .id = V4L2_CID_MPEG_VIDEO_HEVC_DECODE_MODE, ++ .max = V4L2_MPEG_VIDEO_HEVC_DECODE_MODE_SLICE_BASED, ++ .def = V4L2_MPEG_VIDEO_HEVC_DECODE_MODE_SLICE_BASED, ++ }, ++ .required = false, ++ }, ++ { ++ .cfg = { ++ .id = V4L2_CID_MPEG_VIDEO_HEVC_START_CODE, ++ .max = V4L2_MPEG_VIDEO_HEVC_START_CODE_NONE, ++ .def = V4L2_MPEG_VIDEO_HEVC_START_CODE_NONE, ++ }, ++ .required = false, ++ }, ++}; ++ ++#define rpivid_ctrls_COUNT ARRAY_SIZE(rpivid_ctrls) ++ ++void *rpivid_find_control_data(struct rpivid_ctx *ctx, u32 id) ++{ ++ unsigned int i; ++ ++ for (i = 0; ctx->ctrls[i]; i++) ++ if (ctx->ctrls[i]->id == id) ++ return ctx->ctrls[i]->p_cur.p; ++ ++ return NULL; ++} ++ ++static int rpivid_init_ctrls(struct rpivid_dev *dev, struct rpivid_ctx *ctx) ++{ ++ struct v4l2_ctrl_handler *hdl = &ctx->hdl; ++ struct v4l2_ctrl *ctrl; ++ unsigned int ctrl_size; ++ unsigned int i; ++ ++ v4l2_ctrl_handler_init(hdl, rpivid_ctrls_COUNT); ++ if (hdl->error) { ++ v4l2_err(&dev->v4l2_dev, ++ "Failed to initialize control handler\n"); ++ return hdl->error; ++ } ++ ++ ctrl_size = sizeof(ctrl) * rpivid_ctrls_COUNT + 1; ++ ++ ctx->ctrls = kzalloc(ctrl_size, GFP_KERNEL); ++ if (!ctx->ctrls) ++ return -ENOMEM; ++ ++ for (i = 0; i < rpivid_ctrls_COUNT; i++) { ++ ctrl = v4l2_ctrl_new_custom(hdl, &rpivid_ctrls[i].cfg, ++ NULL); ++ if (hdl->error) { ++ v4l2_err(&dev->v4l2_dev, ++ "Failed to create new custom control id=%#x\n", ++ rpivid_ctrls[i].cfg.id); ++ ++ v4l2_ctrl_handler_free(hdl); ++ kfree(ctx->ctrls); ++ return hdl->error; ++ } ++ ++ ctx->ctrls[i] = ctrl; ++ } ++ ++ ctx->fh.ctrl_handler = hdl; ++ v4l2_ctrl_handler_setup(hdl); ++ ++ return 0; ++} ++ ++static int rpivid_request_validate(struct media_request *req) ++{ ++ struct media_request_object *obj; ++ struct v4l2_ctrl_handler *parent_hdl, *hdl; ++ struct rpivid_ctx *ctx = NULL; ++ struct v4l2_ctrl *ctrl_test; ++ unsigned int count; ++ unsigned int i; ++ ++ list_for_each_entry(obj, &req->objects, list) { ++ struct vb2_buffer *vb; ++ ++ if (vb2_request_object_is_buffer(obj)) { ++ vb = container_of(obj, struct vb2_buffer, req_obj); ++ ctx = vb2_get_drv_priv(vb->vb2_queue); ++ ++ break; ++ } ++ } ++ ++ if (!ctx) ++ return -ENOENT; ++ ++ count = vb2_request_buffer_cnt(req); ++ if (!count) { ++ v4l2_info(&ctx->dev->v4l2_dev, ++ "No buffer was provided with the request\n"); ++ return -ENOENT; ++ } else if (count > 1) { ++ v4l2_info(&ctx->dev->v4l2_dev, ++ "More than one buffer was provided with the request\n"); ++ return -EINVAL; ++ } ++ ++ parent_hdl = &ctx->hdl; ++ ++ hdl = v4l2_ctrl_request_hdl_find(req, parent_hdl); ++ if (!hdl) { ++ v4l2_info(&ctx->dev->v4l2_dev, "Missing codec control(s)\n"); ++ return -ENOENT; ++ } ++ ++ for (i = 0; i < rpivid_ctrls_COUNT; i++) { ++ if (!rpivid_ctrls[i].required) ++ continue; ++ ++ ctrl_test = ++ v4l2_ctrl_request_hdl_ctrl_find(hdl, ++ rpivid_ctrls[i].cfg.id); ++ if (!ctrl_test) { ++ v4l2_info(&ctx->dev->v4l2_dev, ++ "Missing required codec control\n"); ++ return -ENOENT; ++ } ++ } ++ ++ v4l2_ctrl_request_hdl_put(hdl); ++ ++ return vb2_request_validate(req); ++} ++ ++static int rpivid_open(struct file *file) ++{ ++ struct rpivid_dev *dev = video_drvdata(file); ++ struct rpivid_ctx *ctx = NULL; ++ int ret; ++ ++ if (mutex_lock_interruptible(&dev->dev_mutex)) ++ return -ERESTARTSYS; ++ ++ ctx = kzalloc(sizeof(*ctx), GFP_KERNEL); ++ if (!ctx) { ++ mutex_unlock(&dev->dev_mutex); ++ return -ENOMEM; ++ } ++ ++ v4l2_fh_init(&ctx->fh, video_devdata(file)); ++ file->private_data = &ctx->fh; ++ ctx->dev = dev; ++ ++ ret = rpivid_init_ctrls(dev, ctx); ++ if (ret) ++ goto err_free; ++ ++ ctx->fh.m2m_ctx = v4l2_m2m_ctx_init(dev->m2m_dev, ctx, ++ &rpivid_queue_init); ++ if (IS_ERR(ctx->fh.m2m_ctx)) { ++ ret = PTR_ERR(ctx->fh.m2m_ctx); ++ goto err_ctrls; ++ } ++ ++ /* The only bit of format info that we can guess now is H265 src ++ * Everything else we need more info for ++ */ ++ ctx->src_fmt.pixelformat = RPIVID_SRC_PIXELFORMAT_DEFAULT; ++ rpivid_prepare_src_format(&ctx->src_fmt); ++ ++ v4l2_fh_add(&ctx->fh); ++ ++ mutex_unlock(&dev->dev_mutex); ++ ++ return 0; ++ ++err_ctrls: ++ v4l2_ctrl_handler_free(&ctx->hdl); ++err_free: ++ kfree(ctx); ++ mutex_unlock(&dev->dev_mutex); ++ ++ return ret; ++} ++ ++static int rpivid_release(struct file *file) ++{ ++ struct rpivid_dev *dev = video_drvdata(file); ++ struct rpivid_ctx *ctx = container_of(file->private_data, ++ struct rpivid_ctx, fh); ++ ++ mutex_lock(&dev->dev_mutex); ++ ++ v4l2_fh_del(&ctx->fh); ++ v4l2_m2m_ctx_release(ctx->fh.m2m_ctx); ++ ++ v4l2_ctrl_handler_free(&ctx->hdl); ++ kfree(ctx->ctrls); ++ ++ v4l2_fh_exit(&ctx->fh); ++ ++ kfree(ctx); ++ ++ mutex_unlock(&dev->dev_mutex); ++ ++ return 0; ++} ++ ++static const struct v4l2_file_operations rpivid_fops = { ++ .owner = THIS_MODULE, ++ .open = rpivid_open, ++ .release = rpivid_release, ++ .poll = v4l2_m2m_fop_poll, ++ .unlocked_ioctl = video_ioctl2, ++ .mmap = v4l2_m2m_fop_mmap, ++}; ++ ++static const struct video_device rpivid_video_device = { ++ .name = RPIVID_NAME, ++ .vfl_dir = VFL_DIR_M2M, ++ .fops = &rpivid_fops, ++ .ioctl_ops = &rpivid_ioctl_ops, ++ .minor = -1, ++ .release = video_device_release_empty, ++ .device_caps = V4L2_CAP_VIDEO_M2M | V4L2_CAP_STREAMING, ++}; ++ ++static const struct v4l2_m2m_ops rpivid_m2m_ops = { ++ .device_run = rpivid_device_run, ++}; ++ ++static const struct media_device_ops rpivid_m2m_media_ops = { ++ .req_validate = rpivid_request_validate, ++ .req_queue = v4l2_m2m_request_queue, ++}; ++ ++static int rpivid_probe(struct platform_device *pdev) ++{ ++ struct rpivid_dev *dev; ++ struct video_device *vfd; ++ int ret; ++ ++ dev = devm_kzalloc(&pdev->dev, sizeof(*dev), GFP_KERNEL); ++ if (!dev) ++ return -ENOMEM; ++ ++ dev->vfd = rpivid_video_device; ++ dev->dev = &pdev->dev; ++ dev->pdev = pdev; ++ ++ ret = 0; ++ ret = rpivid_hw_probe(dev); ++ if (ret) { ++ dev_err(&pdev->dev, "Failed to probe hardware\n"); ++ return ret; ++ } ++ ++ dev->dec_ops = &rpivid_dec_ops_h265; ++ ++ mutex_init(&dev->dev_mutex); ++ ++ ret = v4l2_device_register(&pdev->dev, &dev->v4l2_dev); ++ if (ret) { ++ dev_err(&pdev->dev, "Failed to register V4L2 device\n"); ++ return ret; ++ } ++ ++ vfd = &dev->vfd; ++ vfd->lock = &dev->dev_mutex; ++ vfd->v4l2_dev = &dev->v4l2_dev; ++ ++ snprintf(vfd->name, sizeof(vfd->name), "%s", rpivid_video_device.name); ++ video_set_drvdata(vfd, dev); ++ ++ dev->m2m_dev = v4l2_m2m_init(&rpivid_m2m_ops); ++ if (IS_ERR(dev->m2m_dev)) { ++ v4l2_err(&dev->v4l2_dev, ++ "Failed to initialize V4L2 M2M device\n"); ++ ret = PTR_ERR(dev->m2m_dev); ++ ++ goto err_v4l2; ++ } ++ ++ dev->mdev.dev = &pdev->dev; ++ strscpy(dev->mdev.model, RPIVID_NAME, sizeof(dev->mdev.model)); ++ strscpy(dev->mdev.bus_info, "platform:" RPIVID_NAME, ++ sizeof(dev->mdev.bus_info)); ++ ++ media_device_init(&dev->mdev); ++ dev->mdev.ops = &rpivid_m2m_media_ops; ++ dev->v4l2_dev.mdev = &dev->mdev; ++ ++ ret = video_register_device(vfd, VFL_TYPE_VIDEO, video_nr); ++ if (ret) { ++ v4l2_err(&dev->v4l2_dev, "Failed to register video device\n"); ++ goto err_m2m; ++ } ++ ++ v4l2_info(&dev->v4l2_dev, ++ "Device registered as /dev/video%d\n", vfd->num); ++ ++ ret = v4l2_m2m_register_media_controller(dev->m2m_dev, vfd, ++ MEDIA_ENT_F_PROC_VIDEO_DECODER); ++ if (ret) { ++ v4l2_err(&dev->v4l2_dev, ++ "Failed to initialize V4L2 M2M media controller\n"); ++ goto err_video; ++ } ++ ++ ret = media_device_register(&dev->mdev); ++ if (ret) { ++ v4l2_err(&dev->v4l2_dev, "Failed to register media device\n"); ++ goto err_m2m_mc; ++ } ++ ++ platform_set_drvdata(pdev, dev); ++ ++ return 0; ++ ++err_m2m_mc: ++ v4l2_m2m_unregister_media_controller(dev->m2m_dev); ++err_video: ++ video_unregister_device(&dev->vfd); ++err_m2m: ++ v4l2_m2m_release(dev->m2m_dev); ++err_v4l2: ++ v4l2_device_unregister(&dev->v4l2_dev); ++ ++ return ret; ++} ++ ++static int rpivid_remove(struct platform_device *pdev) ++{ ++ struct rpivid_dev *dev = platform_get_drvdata(pdev); ++ ++ if (media_devnode_is_registered(dev->mdev.devnode)) { ++ media_device_unregister(&dev->mdev); ++ v4l2_m2m_unregister_media_controller(dev->m2m_dev); ++ media_device_cleanup(&dev->mdev); ++ } ++ ++ v4l2_m2m_release(dev->m2m_dev); ++ video_unregister_device(&dev->vfd); ++ v4l2_device_unregister(&dev->v4l2_dev); ++ ++ rpivid_hw_remove(dev); ++ ++ return 0; ++} ++ ++static const struct of_device_id rpivid_dt_match[] = { ++ { ++ .compatible = "raspberrypi,rpivid-vid-decoder", ++ }, ++ { /* sentinel */ } ++}; ++MODULE_DEVICE_TABLE(of, rpivid_dt_match); ++ ++static struct platform_driver rpivid_driver = { ++ .probe = rpivid_probe, ++ .remove = rpivid_remove, ++ .driver = { ++ .name = RPIVID_NAME, ++ .of_match_table = of_match_ptr(rpivid_dt_match), ++ }, ++}; ++module_platform_driver(rpivid_driver); ++ ++MODULE_LICENSE("GPL v2"); ++MODULE_AUTHOR("John Cox "); ++MODULE_DESCRIPTION("Raspberry Pi HEVC V4L2 driver"); +--- /dev/null ++++ b/drivers/staging/media/rpivid/rpivid.h +@@ -0,0 +1,181 @@ ++/* SPDX-License-Identifier: GPL-2.0 */ ++/* ++ * Raspberry Pi HEVC driver ++ * ++ * Copyright (C) 2020 Raspberry Pi (Trading) Ltd ++ * ++ * Based on the Cedrus VPU driver, that is: ++ * ++ * Copyright (C) 2016 Florent Revest ++ * Copyright (C) 2018 Paul Kocialkowski ++ * Copyright (C) 2018 Bootlin ++ */ ++ ++#ifndef _RPIVID_H_ ++#define _RPIVID_H_ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define OPT_DEBUG_POLL_IRQ 0 ++ ++#define RPIVID_NAME "rpivid" ++ ++#define RPIVID_CAPABILITY_UNTILED BIT(0) ++#define RPIVID_CAPABILITY_H265_DEC BIT(1) ++ ++#define RPIVID_QUIRK_NO_DMA_OFFSET BIT(0) ++ ++#define RPIVID_SRC_PIXELFORMAT_DEFAULT V4L2_PIX_FMT_HEVC_SLICE ++ ++enum rpivid_irq_status { ++ RPIVID_IRQ_NONE, ++ RPIVID_IRQ_ERROR, ++ RPIVID_IRQ_OK, ++}; ++ ++struct rpivid_control { ++ struct v4l2_ctrl_config cfg; ++ unsigned char required:1; ++}; ++ ++struct rpivid_h265_run { ++ const struct v4l2_ctrl_hevc_sps *sps; ++ const struct v4l2_ctrl_hevc_pps *pps; ++ const struct v4l2_ctrl_hevc_slice_params *slice_params; ++ const struct v4l2_ctrl_hevc_scaling_matrix *scaling_matrix; ++}; ++ ++struct rpivid_run { ++ struct vb2_v4l2_buffer *src; ++ struct vb2_v4l2_buffer *dst; ++ ++ struct rpivid_h265_run h265; ++}; ++ ++struct rpivid_buffer { ++ struct v4l2_m2m_buffer m2m_buf; ++}; ++ ++struct rpivid_dec_state; ++struct rpivid_dec_env; ++#define RPIVID_DEC_ENV_COUNT 3 ++ ++struct rpivid_gptr { ++ size_t size; ++ __u8 *ptr; ++ dma_addr_t addr; ++ unsigned long attrs; ++}; ++ ++struct rpivid_dev; ++typedef void (*rpivid_irq_callback)(struct rpivid_dev *dev, void *ctx); ++ ++struct rpivid_q_aux; ++#define RPIVID_AUX_ENT_COUNT VB2_MAX_FRAME ++ ++#define RPIVID_P2BUF_COUNT 2 ++ ++struct rpivid_ctx { ++ struct v4l2_fh fh; ++ struct rpivid_dev *dev; ++ ++ struct v4l2_pix_format src_fmt; ++ struct v4l2_pix_format dst_fmt; ++ int dst_fmt_set; ++ ++ struct v4l2_ctrl_handler hdl; ++ struct v4l2_ctrl **ctrls; ++ ++ /* Decode state - stateless decoder my *** */ ++ /* state contains stuff that is only needed in phase0 ++ * it could be held in dec_env but that would be wasteful ++ */ ++ struct rpivid_dec_state *state; ++ struct rpivid_dec_env *dec0; ++ ++ /* Spinlock protecting dec_free */ ++ spinlock_t dec_lock; ++ struct rpivid_dec_env *dec_free; ++ ++ struct rpivid_dec_env *dec_pool; ++ ++ /* Some of these should be in dev */ ++ struct rpivid_gptr bitbufs[1]; /* Will be 2 */ ++ struct rpivid_gptr cmdbufs[1]; /* Will be 2 */ ++ unsigned int p2idx; ++ atomic_t p2out; ++ struct rpivid_gptr pu_bufs[RPIVID_P2BUF_COUNT]; ++ struct rpivid_gptr coeff_bufs[RPIVID_P2BUF_COUNT]; ++ ++ /* Spinlock protecting aux_free */ ++ spinlock_t aux_lock; ++ struct rpivid_q_aux *aux_free; ++ ++ struct rpivid_q_aux *aux_ents[RPIVID_AUX_ENT_COUNT]; ++ ++ unsigned int colmv_stride; ++ unsigned int colmv_picsize; ++}; ++ ++struct rpivid_dec_ops { ++ void (*setup)(struct rpivid_ctx *ctx, struct rpivid_run *run); ++ int (*start)(struct rpivid_ctx *ctx); ++ void (*stop)(struct rpivid_ctx *ctx); ++ void (*trigger)(struct rpivid_ctx *ctx); ++}; ++ ++struct rpivid_variant { ++ unsigned int capabilities; ++ unsigned int quirks; ++ unsigned int mod_rate; ++}; ++ ++struct rpivid_hw_irq_ent; ++ ++struct rpivid_hw_irq_ctrl { ++ /* Spinlock protecting claim and tail */ ++ spinlock_t lock; ++ struct rpivid_hw_irq_ent *claim; ++ struct rpivid_hw_irq_ent *tail; ++ ++ /* Ent for pending irq - also prevents sched */ ++ struct rpivid_hw_irq_ent *irq; ++ /* Non-zero => do not start a new job - outer layer sched pending */ ++ int no_sched; ++ /* Thread CB requested */ ++ bool thread_reqed; ++}; ++ ++struct rpivid_dev { ++ struct v4l2_device v4l2_dev; ++ struct video_device vfd; ++ struct media_device mdev; ++ struct media_pad pad[2]; ++ struct platform_device *pdev; ++ struct device *dev; ++ struct v4l2_m2m_dev *m2m_dev; ++ struct rpivid_dec_ops *dec_ops; ++ ++ /* Device file mutex */ ++ struct mutex dev_mutex; ++ ++ void __iomem *base_irq; ++ void __iomem *base_h265; ++ ++ struct clk *clock; ++ ++ struct rpivid_hw_irq_ctrl ic_active1; ++ struct rpivid_hw_irq_ctrl ic_active2; ++}; ++ ++extern struct rpivid_dec_ops rpivid_dec_ops_h265; ++ ++void *rpivid_find_control_data(struct rpivid_ctx *ctx, u32 id); ++ ++#endif +--- /dev/null ++++ b/drivers/staging/media/rpivid/rpivid_dec.c +@@ -0,0 +1,79 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * Raspberry Pi HEVC driver ++ * ++ * Copyright (C) 2020 Raspberry Pi (Trading) Ltd ++ * ++ * Based on the Cedrus VPU driver, that is: ++ * ++ * Copyright (C) 2016 Florent Revest ++ * Copyright (C) 2018 Paul Kocialkowski ++ * Copyright (C) 2018 Bootlin ++ */ ++ ++#include ++#include ++#include ++#include ++ ++#include "rpivid.h" ++#include "rpivid_dec.h" ++ ++void rpivid_device_run(void *priv) ++{ ++ struct rpivid_ctx *ctx = priv; ++ struct rpivid_dev *dev = ctx->dev; ++ struct rpivid_run run = {}; ++ struct media_request *src_req; ++ ++ run.src = v4l2_m2m_next_src_buf(ctx->fh.m2m_ctx); ++ run.dst = v4l2_m2m_next_dst_buf(ctx->fh.m2m_ctx); ++ ++ if (!run.src || !run.dst) { ++ v4l2_err(&dev->v4l2_dev, "%s: Missing buffer: src=%p, dst=%p\n", ++ __func__, run.src, run.dst); ++ /* We are stuffed - this probably won't dig us out of our ++ * current situation but it is better than nothing ++ */ ++ v4l2_m2m_buf_done_and_job_finish(dev->m2m_dev, ctx->fh.m2m_ctx, ++ VB2_BUF_STATE_ERROR); ++ return; ++ } ++ ++ /* Apply request(s) controls if needed. */ ++ src_req = run.src->vb2_buf.req_obj.req; ++ ++ if (src_req) ++ v4l2_ctrl_request_setup(src_req, &ctx->hdl); ++ ++ switch (ctx->src_fmt.pixelformat) { ++ case V4L2_PIX_FMT_HEVC_SLICE: ++ run.h265.sps = ++ rpivid_find_control_data(ctx, ++ V4L2_CID_MPEG_VIDEO_HEVC_SPS); ++ run.h265.pps = ++ rpivid_find_control_data(ctx, ++ V4L2_CID_MPEG_VIDEO_HEVC_PPS); ++ run.h265.slice_params = ++ rpivid_find_control_data(ctx, ++ V4L2_CID_MPEG_VIDEO_HEVC_SLICE_PARAMS); ++ run.h265.scaling_matrix = ++ rpivid_find_control_data(ctx, ++ V4L2_CID_MPEG_VIDEO_HEVC_SCALING_MATRIX); ++ break; ++ ++ default: ++ break; ++ } ++ ++ v4l2_m2m_buf_copy_metadata(run.src, run.dst, true); ++ ++ dev->dec_ops->setup(ctx, &run); ++ ++ /* Complete request(s) controls if needed. */ ++ ++ if (src_req) ++ v4l2_ctrl_request_complete(src_req, &ctx->hdl); ++ ++ dev->dec_ops->trigger(ctx); ++} +--- /dev/null ++++ b/drivers/staging/media/rpivid/rpivid_dec.h +@@ -0,0 +1,19 @@ ++/* SPDX-License-Identifier: GPL-2.0 */ ++/* ++ * Raspberry Pi HEVC driver ++ * ++ * Copyright (C) 2020 Raspberry Pi (Trading) Ltd ++ * ++ * Based on the Cedrus VPU driver, that is: ++ * ++ * Copyright (C) 2016 Florent Revest ++ * Copyright (C) 2018 Paul Kocialkowski ++ * Copyright (C) 2018 Bootlin ++ */ ++ ++#ifndef _RPIVID_DEC_H_ ++#define _RPIVID_DEC_H_ ++ ++void rpivid_device_run(void *priv); ++ ++#endif +--- /dev/null ++++ b/drivers/staging/media/rpivid/rpivid_h265.c +@@ -0,0 +1,2275 @@ ++// SPDX-License-Identifier: GPL-2.0-or-later ++/* ++ * Raspberry Pi HEVC driver ++ * ++ * Copyright (C) 2020 Raspberry Pi (Trading) Ltd ++ * ++ * Based on the Cedrus VPU driver, that is: ++ * ++ * Copyright (C) 2016 Florent Revest ++ * Copyright (C) 2018 Paul Kocialkowski ++ * Copyright (C) 2018 Bootlin ++ */ ++ ++#include ++#include ++ ++#include ++ ++#include "rpivid.h" ++#include "rpivid_hw.h" ++ ++#define DEBUG_TRACE_P1_CMD 0 ++#define DEBUG_TRACE_EXECUTION 0 ++ ++#if DEBUG_TRACE_EXECUTION ++#define xtrace_in(dev_, de_)\ ++ v4l2_info(&(dev_)->v4l2_dev, "%s[%d]: in\n", __func__,\ ++ (de_) == NULL ? -1 : (de_)->decode_order) ++#define xtrace_ok(dev_, de_)\ ++ v4l2_info(&(dev_)->v4l2_dev, "%s[%d]: ok\n", __func__,\ ++ (de_) == NULL ? -1 : (de_)->decode_order) ++#define xtrace_fin(dev_, de_)\ ++ v4l2_info(&(dev_)->v4l2_dev, "%s[%d]: finish\n", __func__,\ ++ (de_) == NULL ? -1 : (de_)->decode_order) ++#define xtrace_fail(dev_, de_)\ ++ v4l2_info(&(dev_)->v4l2_dev, "%s[%d]: FAIL\n", __func__,\ ++ (de_) == NULL ? -1 : (de_)->decode_order) ++#else ++#define xtrace_in(dev_, de_) ++#define xtrace_ok(dev_, de_) ++#define xtrace_fin(dev_, de_) ++#define xtrace_fail(dev_, de_) ++#endif ++ ++enum hevc_slice_type { ++ HEVC_SLICE_B = 0, ++ HEVC_SLICE_P = 1, ++ HEVC_SLICE_I = 2, ++}; ++ ++enum hevc_layer { L0 = 0, L1 = 1 }; ++ ++static int gptr_alloc(struct rpivid_dev *const dev, struct rpivid_gptr *gptr, ++ size_t size, unsigned long attrs) ++{ ++ gptr->size = size; ++ gptr->attrs = attrs; ++ gptr->addr = 0; ++ gptr->ptr = dma_alloc_attrs(dev->dev, gptr->size, &gptr->addr, ++ GFP_KERNEL, gptr->attrs); ++ return !gptr->ptr ? -ENOMEM : 0; ++} ++ ++static void gptr_free(struct rpivid_dev *const dev, ++ struct rpivid_gptr *const gptr) ++{ ++ if (gptr->ptr) ++ dma_free_attrs(dev->dev, gptr->size, gptr->ptr, gptr->addr, ++ gptr->attrs); ++ gptr->size = 0; ++ gptr->ptr = NULL; ++ gptr->addr = 0; ++ gptr->attrs = 0; ++} ++ ++/* Realloc but do not copy */ ++static int gptr_realloc_new(struct rpivid_dev * const dev, ++ struct rpivid_gptr * const gptr, size_t size) ++{ ++ if (size == gptr->size) ++ return 0; ++ ++ if (gptr->ptr) ++ dma_free_attrs(dev->dev, gptr->size, gptr->ptr, ++ gptr->addr, gptr->attrs); ++ ++ gptr->addr = 0; ++ gptr->size = size; ++ gptr->ptr = dma_alloc_attrs(dev->dev, gptr->size, ++ &gptr->addr, GFP_KERNEL, gptr->attrs); ++ return gptr->ptr ? 0 : -ENOMEM; ++} ++ ++/* floor(log2(x)) */ ++static unsigned int log2_size(size_t x) ++{ ++ unsigned int n = 0; ++ ++ if (x & ~0xffff) { ++ n += 16; ++ x >>= 16; ++ } ++ if (x & ~0xff) { ++ n += 8; ++ x >>= 8; ++ } ++ if (x & ~0xf) { ++ n += 4; ++ x >>= 4; ++ } ++ if (x & ~3) { ++ n += 2; ++ x >>= 2; ++ } ++ return (x & ~1) ? n + 1 : n; ++} ++ ++static size_t round_up_size(const size_t x) ++{ ++ /* Admit no size < 256 */ ++ const unsigned int n = x < 256 ? 8 : log2_size(x) - 1; ++ ++ return x >= (3 << n) ? 4 << n : (3 << n); ++} ++ ++static size_t next_size(const size_t x) ++{ ++ return round_up_size(x + 1); ++} ++ ++#define NUM_SCALING_FACTORS 4064 /* Not a typo = 0xbe0 + 0x400 */ ++ ++#define AXI_BASE64 0 ++ ++#define PROB_BACKUP ((20 << 12) + (20 << 6) + (0 << 0)) ++#define PROB_RELOAD ((20 << 12) + (20 << 0) + (0 << 6)) ++ ++#define HEVC_MAX_REFS V4L2_HEVC_DPB_ENTRIES_NUM_MAX ++ ++////////////////////////////////////////////////////////////////////////////// ++ ++struct rpi_cmd { ++ u32 addr; ++ u32 data; ++} __packed; ++ ++struct rpivid_q_aux { ++ unsigned int refcount; ++ unsigned int q_index; ++ struct rpivid_q_aux *next; ++ struct rpivid_gptr col; ++}; ++ ++////////////////////////////////////////////////////////////////////////////// ++ ++enum rpivid_decode_state { ++ RPIVID_DECODE_SLICE_START, ++ RPIVID_DECODE_SLICE_CONTINUE, ++ RPIVID_DECODE_ERROR_CONTINUE, ++ RPIVID_DECODE_ERROR_DONE, ++ RPIVID_DECODE_PHASE1, ++ RPIVID_DECODE_END, ++}; ++ ++struct rpivid_dec_env { ++ struct rpivid_ctx *ctx; ++ struct rpivid_dec_env *next; ++ ++ enum rpivid_decode_state state; ++ unsigned int decode_order; ++ int p1_status; /* P1 status - what to realloc */ ++ ++ struct rpivid_dec_env *phase_wait_q_next; ++ ++ struct rpi_cmd *cmd_fifo; ++ unsigned int cmd_len, cmd_max; ++ unsigned int num_slice_msgs; ++ unsigned int pic_width_in_ctbs_y; ++ unsigned int pic_height_in_ctbs_y; ++ unsigned int dpbno_col; ++ u32 reg_slicestart; ++ int collocated_from_l0_flag; ++ unsigned int wpp_entry_x; ++ unsigned int wpp_entry_y; ++ ++ u32 rpi_config2; ++ u32 rpi_framesize; ++ u32 rpi_currpoc; ++ ++ struct vb2_v4l2_buffer *frame_buf; // Detached dest buffer ++ unsigned int frame_c_offset; ++ unsigned int frame_stride; ++ dma_addr_t frame_addr; ++ dma_addr_t ref_addrs[16]; ++ struct rpivid_q_aux *frame_aux; ++ struct rpivid_q_aux *col_aux; ++ ++ dma_addr_t pu_base_vc; ++ dma_addr_t coeff_base_vc; ++ u32 pu_stride; ++ u32 coeff_stride; ++ ++ struct rpivid_gptr *bit_copy_gptr; ++ size_t bit_copy_len; ++ struct rpivid_gptr *cmd_copy_gptr; ++ ++ u16 slice_msgs[2 * HEVC_MAX_REFS * 8 + 3]; ++ u8 scaling_factors[NUM_SCALING_FACTORS]; ++ ++ struct rpivid_hw_irq_ent irq_ent; ++}; ++ ++#define member_size(type, member) sizeof(((type *)0)->member) ++ ++struct rpivid_dec_state { ++ struct v4l2_ctrl_hevc_sps sps; ++ struct v4l2_ctrl_hevc_pps pps; ++ ++ // Helper vars & tables derived from sps/pps ++ unsigned int log2_ctb_size; /* log2 width of a CTB */ ++ unsigned int ctb_width; /* Width in CTBs */ ++ unsigned int ctb_height; /* Height in CTBs */ ++ unsigned int ctb_size; /* Pic area in CTBs */ ++ unsigned int num_tile_columns; ++ unsigned int num_tile_rows; ++ u8 column_width[member_size(struct v4l2_ctrl_hevc_pps, ++ column_width_minus1)]; ++ u8 row_height[member_size(struct v4l2_ctrl_hevc_pps, ++ row_height_minus1)]; ++ ++ int *col_bd; ++ int *row_bd; ++ int *ctb_addr_rs_to_ts; ++ int *ctb_addr_ts_to_rs; ++ int *tile_id; ++ ++ // Aux starage for DPB ++ // Hold refs ++ struct rpivid_q_aux *ref_aux[HEVC_MAX_REFS]; ++ struct rpivid_q_aux *frame_aux; ++ ++ // Slice vars ++ unsigned int slice_idx; ++ bool frame_end; ++ bool slice_temporal_mvp; /* Slice flag but constant for frame */ ++ ++ // Temp vars per run - don't actually need to persist ++ u8 *src_buf; ++ dma_addr_t src_addr; ++ const struct v4l2_ctrl_hevc_slice_params *sh; ++ unsigned int nb_refs[2]; ++ unsigned int slice_qp; ++ unsigned int max_num_merge_cand; // 0 if I-slice ++ bool dependent_slice_segment_flag; ++}; ++ ++static inline int clip_int(const int x, const int lo, const int hi) ++{ ++ return x < lo ? lo : x > hi ? hi : x; ++} ++ ++////////////////////////////////////////////////////////////////////////////// ++// Phase 1 command and bit FIFOs ++ ++#if DEBUG_TRACE_P1_CMD ++static int p1_z; ++#endif ++ ++// ???? u16 addr - put in u32 ++static int p1_apb_write(struct rpivid_dec_env *const de, const u16 addr, ++ const u32 data) ++{ ++ if (de->cmd_len == de->cmd_max) ++ de->cmd_fifo = ++ krealloc(de->cmd_fifo, ++ (de->cmd_max *= 2) * sizeof(struct rpi_cmd), ++ GFP_KERNEL); ++ de->cmd_fifo[de->cmd_len].addr = addr; ++ de->cmd_fifo[de->cmd_len].data = data; ++ ++#if DEBUG_TRACE_P1_CMD ++ if (++p1_z < 256) { ++ v4l2_info(&de->ctx->dev->v4l2_dev, "[%02x] %x %x\n", ++ de->cmd_len, addr, data); ++ } ++#endif ++ ++ return de->cmd_len++; ++} ++ ++static int ctb_to_tile(unsigned int ctb, unsigned int *bd, int num) ++{ ++ int i; ++ ++ for (i = 1; ctb >= bd[i]; i++) ++ ; // bd[] has num+1 elements; bd[0]=0; ++ return i - 1; ++} ++ ++static int ctb_to_slice_w_h(unsigned int ctb, int ctb_size, int width, ++ unsigned int *bd, int num) ++{ ++ if (ctb < bd[num - 1]) ++ return ctb_size; ++ else if (width % ctb_size) ++ return width % ctb_size; ++ else ++ return ctb_size; ++} ++ ++static void aux_q_free(struct rpivid_ctx *const ctx, ++ struct rpivid_q_aux *const aq) ++{ ++ struct rpivid_dev *const dev = ctx->dev; ++ ++ gptr_free(dev, &aq->col); ++ kfree(aq); ++} ++ ++static struct rpivid_q_aux *aux_q_alloc(struct rpivid_ctx *const ctx) ++{ ++ struct rpivid_dev *const dev = ctx->dev; ++ struct rpivid_q_aux *const aq = kzalloc(sizeof(*aq), GFP_KERNEL); ++ ++ if (!aq) ++ return NULL; ++ ++ aq->refcount = 1; ++ if (gptr_alloc(dev, &aq->col, ctx->colmv_picsize, ++ DMA_ATTR_FORCE_CONTIGUOUS | DMA_ATTR_NO_KERNEL_MAPPING)) ++ goto fail; ++ ++ return aq; ++ ++fail: ++ kfree(aq); ++ return NULL; ++} ++ ++static struct rpivid_q_aux *aux_q_new(struct rpivid_ctx *const ctx, ++ const unsigned int q_index) ++{ ++ struct rpivid_q_aux *aq; ++ unsigned long lockflags; ++ ++ spin_lock_irqsave(&ctx->aux_lock, lockflags); ++ aq = ctx->aux_free; ++ if (aq) { ++ ctx->aux_free = aq->next; ++ aq->next = NULL; ++ aq->refcount = 1; ++ } ++ spin_unlock_irqrestore(&ctx->aux_lock, lockflags); ++ ++ if (!aq) { ++ aq = aux_q_alloc(ctx); ++ if (!aq) ++ return NULL; ++ } ++ ++ aq->q_index = q_index; ++ ctx->aux_ents[q_index] = aq; ++ return aq; ++} ++ ++static struct rpivid_q_aux *aux_q_ref(struct rpivid_ctx *const ctx, ++ struct rpivid_q_aux *const aq) ++{ ++ if (aq) { ++ unsigned long lockflags; ++ ++ spin_lock_irqsave(&ctx->aux_lock, lockflags); ++ ++ ++aq->refcount; ++ ++ spin_unlock_irqrestore(&ctx->aux_lock, lockflags); ++ } ++ return aq; ++} ++ ++static void aux_q_release(struct rpivid_ctx *const ctx, ++ struct rpivid_q_aux **const paq) ++{ ++ struct rpivid_q_aux *const aq = *paq; ++ *paq = NULL; ++ ++ if (aq) { ++ unsigned long lockflags; ++ ++ spin_lock_irqsave(&ctx->aux_lock, lockflags); ++ ++ if (--aq->refcount == 0) { ++ aq->next = ctx->aux_free; ++ ctx->aux_free = aq; ++ ctx->aux_ents[aq->q_index] = NULL; ++ } ++ ++ spin_unlock_irqrestore(&ctx->aux_lock, lockflags); ++ } ++} ++ ++static void aux_q_init(struct rpivid_ctx *const ctx) ++{ ++ spin_lock_init(&ctx->aux_lock); ++ ctx->aux_free = NULL; ++} ++ ++static void aux_q_uninit(struct rpivid_ctx *const ctx) ++{ ++ struct rpivid_q_aux *aq; ++ ++ ctx->colmv_picsize = 0; ++ ctx->colmv_stride = 0; ++ while ((aq = ctx->aux_free) != NULL) { ++ ctx->aux_free = aq->next; ++ aux_q_free(ctx, aq); ++ } ++} ++ ++////////////////////////////////////////////////////////////////////////////// ++ ++/* ++ * Initialisation process for context variables (CABAC init) ++ * see H.265 9.3.2.2 ++ * ++ * N.B. If comparing with FFmpeg note that this h/w uses slightly different ++ * offsets to FFmpegs array ++ */ ++ ++/* Actual number of values */ ++#define RPI_PROB_VALS 154U ++/* Rounded up as we copy words */ ++#define RPI_PROB_ARRAY_SIZE ((154 + 3) & ~3) ++ ++/* Initialiser values - see tables H.265 9-4 through 9-42 */ ++static const u8 prob_init[3][156] = { ++ { ++ 153, 200, 139, 141, 157, 154, 154, 154, 154, 154, 184, 154, 154, ++ 154, 184, 63, 154, 154, 154, 154, 154, 154, 154, 154, 154, 154, ++ 154, 154, 154, 153, 138, 138, 111, 141, 94, 138, 182, 154, 154, ++ 154, 140, 92, 137, 138, 140, 152, 138, 139, 153, 74, 149, 92, ++ 139, 107, 122, 152, 140, 179, 166, 182, 140, 227, 122, 197, 110, ++ 110, 124, 125, 140, 153, 125, 127, 140, 109, 111, 143, 127, 111, ++ 79, 108, 123, 63, 110, 110, 124, 125, 140, 153, 125, 127, 140, ++ 109, 111, 143, 127, 111, 79, 108, 123, 63, 91, 171, 134, 141, ++ 138, 153, 136, 167, 152, 152, 139, 139, 111, 111, 125, 110, 110, ++ 94, 124, 108, 124, 107, 125, 141, 179, 153, 125, 107, 125, 141, ++ 179, 153, 125, 107, 125, 141, 179, 153, 125, 140, 139, 182, 182, ++ 152, 136, 152, 136, 153, 136, 139, 111, 136, 139, 111, 0, 0, ++ }, ++ { ++ 153, 185, 107, 139, 126, 197, 185, 201, 154, 149, 154, 139, 154, ++ 154, 154, 152, 110, 122, 95, 79, 63, 31, 31, 153, 153, 168, ++ 140, 198, 79, 124, 138, 94, 153, 111, 149, 107, 167, 154, 154, ++ 154, 154, 196, 196, 167, 154, 152, 167, 182, 182, 134, 149, 136, ++ 153, 121, 136, 137, 169, 194, 166, 167, 154, 167, 137, 182, 125, ++ 110, 94, 110, 95, 79, 125, 111, 110, 78, 110, 111, 111, 95, ++ 94, 108, 123, 108, 125, 110, 94, 110, 95, 79, 125, 111, 110, ++ 78, 110, 111, 111, 95, 94, 108, 123, 108, 121, 140, 61, 154, ++ 107, 167, 91, 122, 107, 167, 139, 139, 155, 154, 139, 153, 139, ++ 123, 123, 63, 153, 166, 183, 140, 136, 153, 154, 166, 183, 140, ++ 136, 153, 154, 166, 183, 140, 136, 153, 154, 170, 153, 123, 123, ++ 107, 121, 107, 121, 167, 151, 183, 140, 151, 183, 140, 0, 0, ++ }, ++ { ++ 153, 160, 107, 139, 126, 197, 185, 201, 154, 134, 154, 139, 154, ++ 154, 183, 152, 154, 137, 95, 79, 63, 31, 31, 153, 153, 168, ++ 169, 198, 79, 224, 167, 122, 153, 111, 149, 92, 167, 154, 154, ++ 154, 154, 196, 167, 167, 154, 152, 167, 182, 182, 134, 149, 136, ++ 153, 121, 136, 122, 169, 208, 166, 167, 154, 152, 167, 182, 125, ++ 110, 124, 110, 95, 94, 125, 111, 111, 79, 125, 126, 111, 111, ++ 79, 108, 123, 93, 125, 110, 124, 110, 95, 94, 125, 111, 111, ++ 79, 125, 126, 111, 111, 79, 108, 123, 93, 121, 140, 61, 154, ++ 107, 167, 91, 107, 107, 167, 139, 139, 170, 154, 139, 153, 139, ++ 123, 123, 63, 124, 166, 183, 140, 136, 153, 154, 166, 183, 140, ++ 136, 153, 154, 166, 183, 140, 136, 153, 154, 170, 153, 138, 138, ++ 122, 121, 122, 121, 167, 151, 183, 140, 151, 183, 140, 0, 0, ++ }, ++}; ++ ++static void write_prob(struct rpivid_dec_env *const de, ++ const struct rpivid_dec_state *const s) ++{ ++ u8 dst[RPI_PROB_ARRAY_SIZE]; ++ ++ const unsigned int init_type = ++ ((s->sh->flags & V4L2_HEVC_SLICE_PARAMS_FLAG_CABAC_INIT) != 0 && ++ s->sh->slice_type != HEVC_SLICE_I) ? ++ s->sh->slice_type + 1 : ++ 2 - s->sh->slice_type; ++ const u8 *p = prob_init[init_type]; ++ const int q = clip_int(s->slice_qp, 0, 51); ++ unsigned int i; ++ ++ for (i = 0; i < RPI_PROB_VALS; i++) { ++ int init_value = p[i]; ++ int m = (init_value >> 4) * 5 - 45; ++ int n = ((init_value & 15) << 3) - 16; ++ int pre = 2 * (((m * q) >> 4) + n) - 127; ++ ++ pre ^= pre >> 31; ++ if (pre > 124) ++ pre = 124 + (pre & 1); ++ dst[i] = pre; ++ } ++ for (i = RPI_PROB_VALS; i != RPI_PROB_ARRAY_SIZE; ++i) ++ dst[i] = 0; ++ ++ for (i = 0; i < RPI_PROB_ARRAY_SIZE; i += 4) ++ p1_apb_write(de, 0x1000 + i, ++ dst[i] + (dst[i + 1] << 8) + (dst[i + 2] << 16) + ++ (dst[i + 3] << 24)); ++} ++ ++static void write_scaling_factors(struct rpivid_dec_env *const de) ++{ ++ int i; ++ const u8 *p = (u8 *)de->scaling_factors; ++ ++ for (i = 0; i < NUM_SCALING_FACTORS; i += 4, p += 4) ++ p1_apb_write(de, 0x2000 + i, ++ p[0] + (p[1] << 8) + (p[2] << 16) + (p[3] << 24)); ++} ++ ++static inline __u32 dma_to_axi_addr(dma_addr_t a) ++{ ++ return (__u32)(a >> 6); ++} ++ ++static void write_bitstream(struct rpivid_dec_env *const de, ++ const struct rpivid_dec_state *const s) ++{ ++ // Note that FFmpeg removes emulation prevention bytes, so this is ++ // matched in the configuration here. ++ // Whether that is the correct behaviour or not is not clear in the ++ // spec. ++ const int rpi_use_emu = 1; ++ unsigned int offset = s->sh->data_bit_offset / 8 + 1; ++ const unsigned int len = (s->sh->bit_size + 7) / 8 - offset; ++ dma_addr_t addr; ++ ++ if (s->src_addr != 0) { ++ addr = s->src_addr + offset; ++ } else { ++ memcpy(de->bit_copy_gptr->ptr + de->bit_copy_len, ++ s->src_buf + offset, len); ++ addr = de->bit_copy_gptr->addr + de->bit_copy_len; ++ de->bit_copy_len += (len + 63) & ~63; ++ } ++ offset = addr & 63; ++ ++ p1_apb_write(de, RPI_BFBASE, dma_to_axi_addr(addr)); ++ p1_apb_write(de, RPI_BFNUM, len); ++ p1_apb_write(de, RPI_BFCONTROL, offset + (1 << 7)); // Stop ++ p1_apb_write(de, RPI_BFCONTROL, offset + (rpi_use_emu << 6)); ++} ++ ++////////////////////////////////////////////////////////////////////////////// ++ ++static void write_slice(struct rpivid_dec_env *const de, ++ const struct rpivid_dec_state *const s, ++ const unsigned int slice_w, ++ const unsigned int slice_h) ++{ ++ u32 u32 = (s->sh->slice_type << 12) + ++ (((s->sh->flags & ++ V4L2_HEVC_SLICE_PARAMS_FLAG_SLICE_SAO_LUMA) != 0) ++ << 14) + ++ (((s->sh->flags & ++ V4L2_HEVC_SLICE_PARAMS_FLAG_SLICE_SAO_CHROMA) != 0) ++ << 15) + ++ (slice_w << 17) + (slice_h << 24); ++ ++ u32 |= (s->max_num_merge_cand << 0) + (s->nb_refs[L0] << 4) + ++ (s->nb_refs[L1] << 8); ++ ++ if (s->sh->slice_type == HEVC_SLICE_B) ++ u32 |= ((s->sh->flags & ++ V4L2_HEVC_SLICE_PARAMS_FLAG_MVD_L1_ZERO) != 0) ++ << 16; ++ p1_apb_write(de, RPI_SLICE, u32); ++} ++ ++////////////////////////////////////////////////////////////////////////////// ++// Tiles mode ++ ++static void new_entry_point(struct rpivid_dec_env *const de, ++ const struct rpivid_dec_state *const s, ++ const int do_bte, ++ const int reset_qp_y, const int ctb_addr_ts) ++{ ++ int ctb_col = s->ctb_addr_ts_to_rs[ctb_addr_ts] % ++ de->pic_width_in_ctbs_y; ++ int ctb_row = s->ctb_addr_ts_to_rs[ctb_addr_ts] / ++ de->pic_width_in_ctbs_y; ++ ++ int tile_x = ctb_to_tile(ctb_col, s->col_bd, s->num_tile_columns); ++ int tile_y = ctb_to_tile(ctb_row, s->row_bd, s->num_tile_rows); ++ ++ int endx = s->col_bd[tile_x + 1] - 1; ++ int endy = s->row_bd[tile_y + 1] - 1; ++ ++ u8 slice_w = ctb_to_slice_w_h(ctb_col, 1 << s->log2_ctb_size, ++ s->sps.pic_width_in_luma_samples, ++ s->col_bd, s->num_tile_columns); ++ u8 slice_h = ctb_to_slice_w_h(ctb_row, 1 << s->log2_ctb_size, ++ s->sps.pic_height_in_luma_samples, ++ s->row_bd, s->num_tile_rows); ++ ++ p1_apb_write(de, RPI_TILESTART, ++ s->col_bd[tile_x] + (s->row_bd[tile_y] << 16)); ++ p1_apb_write(de, RPI_TILEEND, endx + (endy << 16)); ++ ++ if (do_bte) ++ p1_apb_write(de, RPI_BEGINTILEEND, endx + (endy << 16)); ++ ++ write_slice(de, s, slice_w, slice_h); ++ ++ if (reset_qp_y) { ++ unsigned int sps_qp_bd_offset = ++ 6 * s->sps.bit_depth_luma_minus8; ++ ++ p1_apb_write(de, RPI_QP, sps_qp_bd_offset + s->slice_qp); ++ } ++ ++ p1_apb_write(de, RPI_MODE, ++ (0xFFFF << 0) + (0x0 << 16) + ++ ((tile_x == s->num_tile_columns - 1) << 17) + ++ ((tile_y == s->num_tile_rows - 1) << 18)); ++ ++ p1_apb_write(de, RPI_CONTROL, (ctb_col << 0) + (ctb_row << 16)); ++} ++ ++////////////////////////////////////////////////////////////////////////////// ++ ++static void new_slice_segment(struct rpivid_dec_env *const de, ++ const struct rpivid_dec_state *const s) ++{ ++ const struct v4l2_ctrl_hevc_sps *const sps = &s->sps; ++ const struct v4l2_ctrl_hevc_pps *const pps = &s->pps; ++ ++ p1_apb_write(de, ++ RPI_SPS0, ++ ((sps->log2_min_luma_coding_block_size_minus3 + 3) << 0) | ++ (s->log2_ctb_size << 4) | ++ ((sps->log2_min_luma_transform_block_size_minus2 + 2) ++ << 8) | ++ ((sps->log2_min_luma_transform_block_size_minus2 + 2 + ++ sps->log2_diff_max_min_luma_transform_block_size) ++ << 12) | ++ ((sps->bit_depth_luma_minus8 + 8) << 16) | ++ ((sps->bit_depth_chroma_minus8 + 8) << 20) | ++ (sps->max_transform_hierarchy_depth_intra << 24) | ++ (sps->max_transform_hierarchy_depth_inter << 28)); ++ ++ p1_apb_write(de, ++ RPI_SPS1, ++ ((sps->pcm_sample_bit_depth_luma_minus1 + 1) << 0) | ++ ((sps->pcm_sample_bit_depth_chroma_minus1 + 1) << 4) | ++ ((sps->log2_min_pcm_luma_coding_block_size_minus3 + 3) ++ << 8) | ++ ((sps->log2_min_pcm_luma_coding_block_size_minus3 + 3 + ++ sps->log2_diff_max_min_pcm_luma_coding_block_size) ++ << 12) | ++ (((sps->flags & V4L2_HEVC_SPS_FLAG_SEPARATE_COLOUR_PLANE) ? ++ 0 : sps->chroma_format_idc) << 16) | ++ ((!!(sps->flags & V4L2_HEVC_SPS_FLAG_AMP_ENABLED)) << 18) | ++ ((!!(sps->flags & V4L2_HEVC_SPS_FLAG_PCM_ENABLED)) << 19) | ++ ((!!(sps->flags & V4L2_HEVC_SPS_FLAG_SCALING_LIST_ENABLED)) ++ << 20) | ++ ((!!(sps->flags & ++ V4L2_HEVC_SPS_FLAG_STRONG_INTRA_SMOOTHING_ENABLED)) ++ << 21)); ++ ++ p1_apb_write(de, ++ RPI_PPS, ++ ((s->log2_ctb_size - pps->diff_cu_qp_delta_depth) << 0) | ++ ((!!(pps->flags & V4L2_HEVC_PPS_FLAG_CU_QP_DELTA_ENABLED)) ++ << 4) | ++ ((!!(pps->flags & ++ V4L2_HEVC_PPS_FLAG_TRANSQUANT_BYPASS_ENABLED)) ++ << 5) | ++ ((!!(pps->flags & V4L2_HEVC_PPS_FLAG_TRANSFORM_SKIP_ENABLED)) ++ << 6) | ++ ((!!(pps->flags & ++ V4L2_HEVC_PPS_FLAG_SIGN_DATA_HIDING_ENABLED)) ++ << 7) | ++ (((pps->pps_cb_qp_offset + s->sh->slice_cb_qp_offset) & 255) ++ << 8) | ++ (((pps->pps_cr_qp_offset + s->sh->slice_cr_qp_offset) & 255) ++ << 16) | ++ ((!!(pps->flags & ++ V4L2_HEVC_PPS_FLAG_CONSTRAINED_INTRA_PRED)) ++ << 24)); ++ ++ if ((sps->flags & V4L2_HEVC_SPS_FLAG_SCALING_LIST_ENABLED) != 0) ++ write_scaling_factors(de); ++ ++ if (!s->dependent_slice_segment_flag) { ++ int ctb_col = s->sh->slice_segment_addr % ++ de->pic_width_in_ctbs_y; ++ int ctb_row = s->sh->slice_segment_addr / ++ de->pic_width_in_ctbs_y; ++ ++ de->reg_slicestart = (ctb_col << 0) + (ctb_row << 16); ++ } ++ ++ p1_apb_write(de, RPI_SLICESTART, de->reg_slicestart); ++} ++ ++////////////////////////////////////////////////////////////////////////////// ++// Slice messages ++ ++static void msg_slice(struct rpivid_dec_env *const de, const u16 msg) ++{ ++ de->slice_msgs[de->num_slice_msgs++] = msg; ++} ++ ++static void program_slicecmds(struct rpivid_dec_env *const de, ++ const int sliceid) ++{ ++ int i; ++ ++ p1_apb_write(de, RPI_SLICECMDS, de->num_slice_msgs + (sliceid << 8)); ++ ++ for (i = 0; i < de->num_slice_msgs; i++) ++ p1_apb_write(de, 0x4000 + 4 * i, de->slice_msgs[i] & 0xffff); ++} ++ ++// NoBackwardPredictionFlag 8.3.5 ++// Simply checks POCs ++static int has_backward(const struct v4l2_hevc_dpb_entry *const dpb, ++ const __u8 *const idx, const unsigned int n, ++ const unsigned int cur_poc) ++{ ++ unsigned int i; ++ ++ for (i = 0; i < n; ++i) { ++ // Compare mod 2^16 ++ // We only get u16 pocs & 8.3.1 says ++ // "The bitstream shall not contain data that result in values ++ // of DiffPicOrderCnt( picA, picB ) used in the decoding ++ // process that are not in the range of −2^15 to 2^15 − 1, ++ // inclusive." ++ if (((cur_poc - dpb[idx[i]].pic_order_cnt[0]) & 0x8000) != 0) ++ return 0; ++ } ++ return 1; ++} ++ ++static void pre_slice_decode(struct rpivid_dec_env *const de, ++ const struct rpivid_dec_state *const s) ++{ ++ const struct v4l2_ctrl_hevc_slice_params *const sh = s->sh; ++ int weighted_pred_flag, idx; ++ u16 cmd_slice; ++ unsigned int collocated_from_l0_flag; ++ ++ de->num_slice_msgs = 0; ++ ++ cmd_slice = 0; ++ if (sh->slice_type == HEVC_SLICE_I) ++ cmd_slice = 1; ++ if (sh->slice_type == HEVC_SLICE_P) ++ cmd_slice = 2; ++ if (sh->slice_type == HEVC_SLICE_B) ++ cmd_slice = 3; ++ ++ cmd_slice |= (s->nb_refs[L0] << 2) | (s->nb_refs[L1] << 6) | ++ (s->max_num_merge_cand << 11); ++ ++ collocated_from_l0_flag = ++ !s->slice_temporal_mvp || ++ sh->slice_type != HEVC_SLICE_B || ++ (sh->flags & V4L2_HEVC_SLICE_PARAMS_FLAG_COLLOCATED_FROM_L0); ++ cmd_slice |= collocated_from_l0_flag << 14; ++ ++ if (sh->slice_type == HEVC_SLICE_P || sh->slice_type == HEVC_SLICE_B) { ++ // Flag to say all reference pictures are from the past ++ const int no_backward_pred_flag = ++ has_backward(sh->dpb, sh->ref_idx_l0, s->nb_refs[L0], ++ sh->slice_pic_order_cnt) && ++ has_backward(sh->dpb, sh->ref_idx_l1, s->nb_refs[L1], ++ sh->slice_pic_order_cnt); ++ cmd_slice |= no_backward_pred_flag << 10; ++ msg_slice(de, cmd_slice); ++ ++ if (s->slice_temporal_mvp) { ++ const __u8 *const rpl = collocated_from_l0_flag ? ++ sh->ref_idx_l0 : sh->ref_idx_l1; ++ de->dpbno_col = rpl[sh->collocated_ref_idx]; ++ //v4l2_info(&de->ctx->dev->v4l2_dev, ++ // "L0=%d col_ref_idx=%d, ++ // dpb_no=%d\n", collocated_from_l0_flag, ++ // sh->collocated_ref_idx, de->dpbno_col); ++ } ++ ++ // Write reference picture descriptions ++ weighted_pred_flag = ++ sh->slice_type == HEVC_SLICE_P ? ++ !!(s->pps.flags & V4L2_HEVC_PPS_FLAG_WEIGHTED_PRED) : ++ !!(s->pps.flags & V4L2_HEVC_PPS_FLAG_WEIGHTED_BIPRED); ++ ++ for (idx = 0; idx < s->nb_refs[L0]; ++idx) { ++ unsigned int dpb_no = sh->ref_idx_l0[idx]; ++ //v4l2_info(&de->ctx->dev->v4l2_dev, ++ // "L0[%d]=dpb[%d]\n", idx, dpb_no); ++ ++ msg_slice(de, ++ dpb_no | ++ (sh->dpb[dpb_no].rps == ++ V4L2_HEVC_DPB_ENTRY_RPS_LT_CURR ? ++ (1 << 4) : 0) | ++ (weighted_pred_flag ? (3 << 5) : 0)); ++ msg_slice(de, sh->dpb[dpb_no].pic_order_cnt[0]); ++ ++ if (weighted_pred_flag) { ++ const struct v4l2_hevc_pred_weight_table ++ *const w = &sh->pred_weight_table; ++ const int luma_weight_denom = ++ (1 << w->luma_log2_weight_denom); ++ const unsigned int chroma_log2_weight_denom = ++ (w->luma_log2_weight_denom + ++ w->delta_chroma_log2_weight_denom); ++ const int chroma_weight_denom = ++ (1 << chroma_log2_weight_denom); ++ ++ msg_slice(de, ++ w->luma_log2_weight_denom | ++ (((w->delta_luma_weight_l0[idx] + ++ luma_weight_denom) & 0x1ff) ++ << 3)); ++ msg_slice(de, w->luma_offset_l0[idx] & 0xff); ++ msg_slice(de, ++ chroma_log2_weight_denom | ++ (((w->delta_chroma_weight_l0[idx][0] + ++ chroma_weight_denom) & 0x1ff) ++ << 3)); ++ msg_slice(de, ++ w->chroma_offset_l0[idx][0] & 0xff); ++ msg_slice(de, ++ chroma_log2_weight_denom | ++ (((w->delta_chroma_weight_l0[idx][1] + ++ chroma_weight_denom) & 0x1ff) ++ << 3)); ++ msg_slice(de, ++ w->chroma_offset_l0[idx][1] & 0xff); ++ } ++ } ++ ++ for (idx = 0; idx < s->nb_refs[L1]; ++idx) { ++ unsigned int dpb_no = sh->ref_idx_l1[idx]; ++ //v4l2_info(&de->ctx->dev->v4l2_dev, ++ // "L1[%d]=dpb[%d]\n", idx, dpb_no); ++ msg_slice(de, ++ dpb_no | ++ (sh->dpb[dpb_no].rps == ++ V4L2_HEVC_DPB_ENTRY_RPS_LT_CURR ? ++ (1 << 4) : 0) | ++ (weighted_pred_flag ? (3 << 5) : 0)); ++ msg_slice(de, sh->dpb[dpb_no].pic_order_cnt[0]); ++ if (weighted_pred_flag) { ++ const struct v4l2_hevc_pred_weight_table ++ *const w = &sh->pred_weight_table; ++ const int luma_weight_denom = ++ (1 << w->luma_log2_weight_denom); ++ const unsigned int chroma_log2_weight_denom = ++ (w->luma_log2_weight_denom + ++ w->delta_chroma_log2_weight_denom); ++ const int chroma_weight_denom = ++ (1 << chroma_log2_weight_denom); ++ ++ msg_slice(de, ++ w->luma_log2_weight_denom | ++ (((w->delta_luma_weight_l1[idx] + ++ luma_weight_denom) & 0x1ff) << 3)); ++ msg_slice(de, w->luma_offset_l1[idx] & 0xff); ++ msg_slice(de, ++ chroma_log2_weight_denom | ++ (((w->delta_chroma_weight_l1[idx][0] + ++ chroma_weight_denom) & 0x1ff) ++ << 3)); ++ msg_slice(de, ++ w->chroma_offset_l1[idx][0] & 0xff); ++ msg_slice(de, ++ chroma_log2_weight_denom | ++ (((w->delta_chroma_weight_l1[idx][1] + ++ chroma_weight_denom) & 0x1ff) ++ << 3)); ++ msg_slice(de, ++ w->chroma_offset_l1[idx][1] & 0xff); ++ } ++ } ++ } else { ++ msg_slice(de, cmd_slice); ++ } ++ ++ msg_slice(de, ++ (sh->slice_beta_offset_div2 & 15) | ++ ((sh->slice_tc_offset_div2 & 15) << 4) | ++ ((sh->flags & ++ V4L2_HEVC_SLICE_PARAMS_FLAG_SLICE_DEBLOCKING_FILTER_DISABLED) ? ++ 1 << 8 : 0) | ++ ((sh->flags & ++ V4L2_HEVC_SLICE_PARAMS_FLAG_SLICE_LOOP_FILTER_ACROSS_SLICES_ENABLED) ? ++ 1 << 9 : 0) | ++ ((s->pps.flags & ++ V4L2_HEVC_PPS_FLAG_LOOP_FILTER_ACROSS_TILES_ENABLED) ? ++ 1 << 10 : 0)); ++ ++ msg_slice(de, ((sh->slice_cr_qp_offset & 31) << 5) + ++ (sh->slice_cb_qp_offset & 31)); // CMD_QPOFF ++} ++ ++////////////////////////////////////////////////////////////////////////////// ++// Write STATUS register with expected end CTU address of previous slice ++ ++static void end_previous_slice(struct rpivid_dec_env *const de, ++ const struct rpivid_dec_state *const s, ++ const int ctb_addr_ts) ++{ ++ int last_x = ++ s->ctb_addr_ts_to_rs[ctb_addr_ts - 1] % de->pic_width_in_ctbs_y; ++ int last_y = ++ s->ctb_addr_ts_to_rs[ctb_addr_ts - 1] / de->pic_width_in_ctbs_y; ++ ++ p1_apb_write(de, RPI_STATUS, 1 + (last_x << 5) + (last_y << 18)); ++} ++ ++static void wpp_pause(struct rpivid_dec_env *const de, int ctb_row) ++{ ++ p1_apb_write(de, RPI_STATUS, (ctb_row << 18) + 0x25); ++ p1_apb_write(de, RPI_TRANSFER, PROB_BACKUP); ++ p1_apb_write(de, RPI_MODE, ++ ctb_row == de->pic_height_in_ctbs_y - 1 ? ++ 0x70000 : 0x30000); ++ p1_apb_write(de, RPI_CONTROL, (ctb_row << 16) + 2); ++} ++ ++static void wpp_end_previous_slice(struct rpivid_dec_env *const de, ++ const struct rpivid_dec_state *const s, ++ int ctb_addr_ts) ++{ ++ int new_x = s->sh->slice_segment_addr % de->pic_width_in_ctbs_y; ++ int new_y = s->sh->slice_segment_addr / de->pic_width_in_ctbs_y; ++ int last_x = ++ s->ctb_addr_ts_to_rs[ctb_addr_ts - 1] % de->pic_width_in_ctbs_y; ++ int last_y = ++ s->ctb_addr_ts_to_rs[ctb_addr_ts - 1] / de->pic_width_in_ctbs_y; ++ ++ if (de->wpp_entry_x < 2 && (de->wpp_entry_y < new_y || new_x > 2) && ++ de->pic_width_in_ctbs_y > 2) ++ wpp_pause(de, last_y); ++ p1_apb_write(de, RPI_STATUS, 1 + (last_x << 5) + (last_y << 18)); ++ if (new_x == 2 || (de->pic_width_in_ctbs_y == 2 && ++ de->wpp_entry_y < new_y)) ++ p1_apb_write(de, RPI_TRANSFER, PROB_BACKUP); ++} ++ ++////////////////////////////////////////////////////////////////////////////// ++// Wavefront mode ++ ++static void wpp_entry_point(struct rpivid_dec_env *const de, ++ const struct rpivid_dec_state *const s, ++ const int do_bte, ++ const int reset_qp_y, const int ctb_addr_ts) ++{ ++ int ctb_size = 1 << s->log2_ctb_size; ++ int ctb_addr_rs = s->ctb_addr_ts_to_rs[ctb_addr_ts]; ++ ++ int ctb_col = de->wpp_entry_x = ctb_addr_rs % de->pic_width_in_ctbs_y; ++ int ctb_row = de->wpp_entry_y = ctb_addr_rs / de->pic_width_in_ctbs_y; ++ ++ int endx = de->pic_width_in_ctbs_y - 1; ++ int endy = ctb_row; ++ ++ u8 slice_w = ctb_to_slice_w_h(ctb_col, ctb_size, ++ s->sps.pic_width_in_luma_samples, ++ s->col_bd, s->num_tile_columns); ++ u8 slice_h = ctb_to_slice_w_h(ctb_row, ctb_size, ++ s->sps.pic_height_in_luma_samples, ++ s->row_bd, s->num_tile_rows); ++ ++ p1_apb_write(de, RPI_TILESTART, 0); ++ p1_apb_write(de, RPI_TILEEND, endx + (endy << 16)); ++ ++ if (do_bte) ++ p1_apb_write(de, RPI_BEGINTILEEND, endx + (endy << 16)); ++ ++ write_slice(de, s, slice_w, ++ ctb_row == de->pic_height_in_ctbs_y - 1 ? ++ slice_h : ctb_size); ++ ++ if (reset_qp_y) { ++ unsigned int sps_qp_bd_offset = ++ 6 * s->sps.bit_depth_luma_minus8; ++ ++ p1_apb_write(de, RPI_QP, sps_qp_bd_offset + s->slice_qp); ++ } ++ ++ p1_apb_write(de, RPI_MODE, ++ ctb_row == de->pic_height_in_ctbs_y - 1 ? ++ 0x60001 : 0x20001); ++ p1_apb_write(de, RPI_CONTROL, (ctb_col << 0) + (ctb_row << 16)); ++} ++ ++////////////////////////////////////////////////////////////////////////////// ++// Wavefront mode ++ ++static void wpp_decode_slice(struct rpivid_dec_env *const de, ++ const struct rpivid_dec_state *const s, ++ const struct v4l2_ctrl_hevc_slice_params *sh, ++ int ctb_addr_ts) ++{ ++ int i, reset_qp_y = 1; ++ int indep = !s->dependent_slice_segment_flag; ++ int ctb_col = s->sh->slice_segment_addr % de->pic_width_in_ctbs_y; ++ ++ if (ctb_addr_ts) ++ wpp_end_previous_slice(de, s, ctb_addr_ts); ++ pre_slice_decode(de, s); ++ write_bitstream(de, s); ++ if (ctb_addr_ts == 0 || indep || de->pic_width_in_ctbs_y == 1) ++ write_prob(de, s); ++ else if (ctb_col == 0) ++ p1_apb_write(de, RPI_TRANSFER, PROB_RELOAD); ++ else ++ reset_qp_y = 0; ++ program_slicecmds(de, s->slice_idx); ++ new_slice_segment(de, s); ++ wpp_entry_point(de, s, indep, reset_qp_y, ctb_addr_ts); ++ ++ for (i = 0; i < s->sh->num_entry_point_offsets; i++) { ++ int ctb_addr_rs = s->ctb_addr_ts_to_rs[ctb_addr_ts]; ++ int ctb_row = ctb_addr_rs / de->pic_width_in_ctbs_y; ++ int last_x = de->pic_width_in_ctbs_y - 1; ++ ++ if (de->pic_width_in_ctbs_y > 2) ++ wpp_pause(de, ctb_row); ++ p1_apb_write(de, RPI_STATUS, ++ (ctb_row << 18) + (last_x << 5) + 2); ++ if (de->pic_width_in_ctbs_y == 2) ++ p1_apb_write(de, RPI_TRANSFER, PROB_BACKUP); ++ if (de->pic_width_in_ctbs_y == 1) ++ write_prob(de, s); ++ else ++ p1_apb_write(de, RPI_TRANSFER, PROB_RELOAD); ++ ctb_addr_ts += s->column_width[0]; ++ wpp_entry_point(de, s, 0, 1, ctb_addr_ts); ++ } ++} ++ ++////////////////////////////////////////////////////////////////////////////// ++// Tiles mode ++ ++static void decode_slice(struct rpivid_dec_env *const de, ++ const struct rpivid_dec_state *const s, ++ const struct v4l2_ctrl_hevc_slice_params *const sh, ++ int ctb_addr_ts) ++{ ++ int i, reset_qp_y; ++ ++ if (ctb_addr_ts) ++ end_previous_slice(de, s, ctb_addr_ts); ++ ++ pre_slice_decode(de, s); ++ write_bitstream(de, s); ++ ++#if DEBUG_TRACE_P1_CMD ++ if (p1_z < 256) { ++ v4l2_info(&de->ctx->dev->v4l2_dev, ++ "TS=%d, tile=%d/%d, dss=%d, flags=%#llx\n", ++ ctb_addr_ts, s->tile_id[ctb_addr_ts], ++ s->tile_id[ctb_addr_ts - 1], ++ s->dependent_slice_segment_flag, sh->flags); ++ } ++#endif ++ ++ reset_qp_y = ctb_addr_ts == 0 || ++ s->tile_id[ctb_addr_ts] != s->tile_id[ctb_addr_ts - 1] || ++ !s->dependent_slice_segment_flag; ++ if (reset_qp_y) ++ write_prob(de, s); ++ ++ program_slicecmds(de, s->slice_idx); ++ new_slice_segment(de, s); ++ new_entry_point(de, s, !s->dependent_slice_segment_flag, reset_qp_y, ++ ctb_addr_ts); ++ ++ for (i = 0; i < s->sh->num_entry_point_offsets; i++) { ++ int ctb_addr_rs = s->ctb_addr_ts_to_rs[ctb_addr_ts]; ++ int ctb_col = ctb_addr_rs % de->pic_width_in_ctbs_y; ++ int ctb_row = ctb_addr_rs / de->pic_width_in_ctbs_y; ++ int tile_x = ctb_to_tile(ctb_col, s->col_bd, ++ s->num_tile_columns - 1); ++ int tile_y = ++ ctb_to_tile(ctb_row, s->row_bd, s->num_tile_rows - 1); ++ int last_x = s->col_bd[tile_x + 1] - 1; ++ int last_y = s->row_bd[tile_y + 1] - 1; ++ ++ p1_apb_write(de, RPI_STATUS, ++ 2 + (last_x << 5) + (last_y << 18)); ++ write_prob(de, s); ++ ctb_addr_ts += s->column_width[tile_x] * s->row_height[tile_y]; ++ new_entry_point(de, s, 0, 1, ctb_addr_ts); ++ } ++} ++ ++////////////////////////////////////////////////////////////////////////////// ++// Scaling factors ++ ++static void expand_scaling_list(const unsigned int size_id, ++ const unsigned int matrix_id, u8 *const dst0, ++ const u8 *const src0, uint8_t dc) ++{ ++ u8 *d; ++ unsigned int x, y; ++ ++ // FIXME: matrix_id is unused ? ++ switch (size_id) { ++ case 0: ++ memcpy(dst0, src0, 16); ++ break; ++ case 1: ++ memcpy(dst0, src0, 64); ++ break; ++ case 2: ++ d = dst0; ++ ++ for (y = 0; y != 16; y++) { ++ const u8 *s = src0 + (y >> 1) * 8; ++ ++ for (x = 0; x != 8; ++x) { ++ *d++ = *s; ++ *d++ = *s++; ++ } ++ } ++ dst0[0] = dc; ++ break; ++ default: ++ d = dst0; ++ ++ for (y = 0; y != 32; y++) { ++ const u8 *s = src0 + (y >> 2) * 8; ++ ++ for (x = 0; x != 8; ++x) { ++ *d++ = *s; ++ *d++ = *s; ++ *d++ = *s; ++ *d++ = *s++; ++ } ++ } ++ dst0[0] = dc; ++ break; ++ } ++} ++ ++static void populate_scaling_factors(const struct rpivid_run *const run, ++ struct rpivid_dec_env *const de, ++ const struct rpivid_dec_state *const s) ++{ ++ const struct v4l2_ctrl_hevc_scaling_matrix *const sl = ++ run->h265.scaling_matrix; ++ // Array of constants for scaling factors ++ static const u32 scaling_factor_offsets[4][6] = { ++ // MID0 MID1 MID2 MID3 MID4 MID5 ++ // SID0 (4x4) ++ { 0x0000, 0x0010, 0x0020, 0x0030, 0x0040, 0x0050 }, ++ // SID1 (8x8) ++ { 0x0060, 0x00A0, 0x00E0, 0x0120, 0x0160, 0x01A0 }, ++ // SID2 (16x16) ++ { 0x01E0, 0x02E0, 0x03E0, 0x04E0, 0x05E0, 0x06E0 }, ++ // SID3 (32x32) ++ { 0x07E0, 0x0BE0, 0x0000, 0x0000, 0x0000, 0x0000 } ++ }; ++ ++ unsigned int mid; ++ ++ for (mid = 0; mid < 6; mid++) ++ expand_scaling_list(0, mid, ++ de->scaling_factors + ++ scaling_factor_offsets[0][mid], ++ sl->scaling_list_4x4[mid], 0); ++ for (mid = 0; mid < 6; mid++) ++ expand_scaling_list(1, mid, ++ de->scaling_factors + ++ scaling_factor_offsets[1][mid], ++ sl->scaling_list_8x8[mid], 0); ++ for (mid = 0; mid < 6; mid++) ++ expand_scaling_list(2, mid, ++ de->scaling_factors + ++ scaling_factor_offsets[2][mid], ++ sl->scaling_list_16x16[mid], ++ sl->scaling_list_dc_coef_16x16[mid]); ++ for (mid = 0; mid < 2; mid += 1) ++ expand_scaling_list(3, mid, ++ de->scaling_factors + ++ scaling_factor_offsets[3][mid], ++ sl->scaling_list_32x32[mid], ++ sl->scaling_list_dc_coef_32x32[mid]); ++} ++ ++static void free_ps_info(struct rpivid_dec_state *const s) ++{ ++ kfree(s->ctb_addr_rs_to_ts); ++ s->ctb_addr_rs_to_ts = NULL; ++ kfree(s->ctb_addr_ts_to_rs); ++ s->ctb_addr_ts_to_rs = NULL; ++ kfree(s->tile_id); ++ s->tile_id = NULL; ++ ++ kfree(s->col_bd); ++ s->col_bd = NULL; ++ kfree(s->row_bd); ++ s->row_bd = NULL; ++} ++ ++static int updated_ps(struct rpivid_dec_state *const s) ++{ ++ unsigned int ctb_addr_rs; ++ int j, x, y, tile_id; ++ unsigned int i; ++ ++ free_ps_info(s); ++ ++ // Inferred parameters ++ s->log2_ctb_size = s->sps.log2_min_luma_coding_block_size_minus3 + 3 + ++ s->sps.log2_diff_max_min_luma_coding_block_size; ++ ++ s->ctb_width = (s->sps.pic_width_in_luma_samples + ++ (1 << s->log2_ctb_size) - 1) >> ++ s->log2_ctb_size; ++ s->ctb_height = (s->sps.pic_height_in_luma_samples + ++ (1 << s->log2_ctb_size) - 1) >> ++ s->log2_ctb_size; ++ s->ctb_size = s->ctb_width * s->ctb_height; ++ ++ // Inferred parameters ++ ++ if (!(s->pps.flags & V4L2_HEVC_PPS_FLAG_TILES_ENABLED)) { ++ s->num_tile_columns = 1; ++ s->num_tile_rows = 1; ++ s->column_width[0] = s->ctb_width; ++ s->row_height[0] = s->ctb_height; ++ } else { ++ s->num_tile_columns = s->pps.num_tile_columns_minus1 + 1; ++ s->num_tile_rows = s->pps.num_tile_rows_minus1 + 1; ++ for (i = 0; i < s->num_tile_columns; ++i) ++ s->column_width[i] = s->pps.column_width_minus1[i] + 1; ++ for (i = 0; i < s->num_tile_rows; ++i) ++ s->row_height[i] = s->pps.row_height_minus1[i] + 1; ++ } ++ ++ s->col_bd = kmalloc((s->num_tile_columns + 1) * sizeof(*s->col_bd), ++ GFP_KERNEL); ++ s->row_bd = kmalloc((s->num_tile_rows + 1) * sizeof(*s->row_bd), ++ GFP_KERNEL); ++ ++ s->col_bd[0] = 0; ++ for (i = 0; i < s->num_tile_columns; i++) ++ s->col_bd[i + 1] = s->col_bd[i] + s->column_width[i]; ++ ++ s->row_bd[0] = 0; ++ for (i = 0; i < s->num_tile_rows; i++) ++ s->row_bd[i + 1] = s->row_bd[i] + s->row_height[i]; ++ ++ s->ctb_addr_rs_to_ts = kmalloc_array(s->ctb_size, ++ sizeof(*s->ctb_addr_rs_to_ts), ++ GFP_KERNEL); ++ s->ctb_addr_ts_to_rs = kmalloc_array(s->ctb_size, ++ sizeof(*s->ctb_addr_ts_to_rs), ++ GFP_KERNEL); ++ s->tile_id = kmalloc_array(s->ctb_size, sizeof(*s->tile_id), ++ GFP_KERNEL); ++ ++ for (ctb_addr_rs = 0; ctb_addr_rs < s->ctb_size; ctb_addr_rs++) { ++ int tb_x = ctb_addr_rs % s->ctb_width; ++ int tb_y = ctb_addr_rs / s->ctb_width; ++ int tile_x = 0; ++ int tile_y = 0; ++ int val = 0; ++ ++ for (i = 0; i < s->num_tile_columns; i++) { ++ if (tb_x < s->col_bd[i + 1]) { ++ tile_x = i; ++ break; ++ } ++ } ++ ++ for (i = 0; i < s->num_tile_rows; i++) { ++ if (tb_y < s->row_bd[i + 1]) { ++ tile_y = i; ++ break; ++ } ++ } ++ ++ for (i = 0; i < tile_x; i++) ++ val += s->row_height[tile_y] * s->column_width[i]; ++ for (i = 0; i < tile_y; i++) ++ val += s->ctb_width * s->row_height[i]; ++ ++ val += (tb_y - s->row_bd[tile_y]) * s->column_width[tile_x] + ++ tb_x - s->col_bd[tile_x]; ++ ++ s->ctb_addr_rs_to_ts[ctb_addr_rs] = val; ++ s->ctb_addr_ts_to_rs[val] = ctb_addr_rs; ++ } ++ ++ for (j = 0, tile_id = 0; j < s->num_tile_rows; j++) ++ for (i = 0; i < s->num_tile_columns; i++, tile_id++) ++ for (y = s->row_bd[j]; y < s->row_bd[j + 1]; y++) ++ for (x = s->col_bd[i]; ++ x < s->col_bd[i + 1]; ++ x++) ++ s->tile_id[s->ctb_addr_rs_to_ts ++ [y * s->ctb_width + ++ x]] = tile_id; ++ ++ return 0; ++} ++ ++static int frame_end(struct rpivid_dev *const dev, ++ struct rpivid_dec_env *const de, ++ const struct rpivid_dec_state *const s) ++{ ++ const unsigned int last_x = s->col_bd[s->num_tile_columns] - 1; ++ const unsigned int last_y = s->row_bd[s->num_tile_rows] - 1; ++ size_t cmd_size; ++ ++ if (s->pps.flags & V4L2_HEVC_PPS_FLAG_ENTROPY_CODING_SYNC_ENABLED) { ++ if (de->wpp_entry_x < 2 && de->pic_width_in_ctbs_y > 2) ++ wpp_pause(de, last_y); ++ } ++ p1_apb_write(de, RPI_STATUS, 1 + (last_x << 5) + (last_y << 18)); ++ ++ // Copy commands out to dma buf ++ cmd_size = de->cmd_len * sizeof(de->cmd_fifo[0]); ++ ++ if (!de->cmd_copy_gptr->ptr || cmd_size > de->cmd_copy_gptr->size) { ++ size_t cmd_alloc = round_up_size(cmd_size); ++ ++ if (gptr_realloc_new(dev, de->cmd_copy_gptr, cmd_alloc)) { ++ v4l2_err(&dev->v4l2_dev, ++ "Alloc cmd buffer (%d): FAILED\n", cmd_alloc); ++ return -ENOMEM; ++ } ++ v4l2_info(&dev->v4l2_dev, "Alloc cmd buffer (%d): OK\n", ++ cmd_alloc); ++ } ++ ++ memcpy(de->cmd_copy_gptr->ptr, de->cmd_fifo, cmd_size); ++ return 0; ++} ++ ++static void setup_colmv(struct rpivid_ctx *const ctx, struct rpivid_run *run, ++ struct rpivid_dec_state *const s) ++{ ++ ctx->colmv_stride = ALIGN(s->sps.pic_width_in_luma_samples, 64); ++ ctx->colmv_picsize = ctx->colmv_stride * ++ (ALIGN(s->sps.pic_height_in_luma_samples, 64) >> 4); ++} ++ ++// Can be called from irq context ++static struct rpivid_dec_env *dec_env_new(struct rpivid_ctx *const ctx) ++{ ++ struct rpivid_dec_env *de; ++ unsigned long lock_flags; ++ ++ spin_lock_irqsave(&ctx->dec_lock, lock_flags); ++ ++ de = ctx->dec_free; ++ if (de) { ++ ctx->dec_free = de->next; ++ de->next = NULL; ++ de->state = RPIVID_DECODE_SLICE_START; ++ } ++ ++ spin_unlock_irqrestore(&ctx->dec_lock, lock_flags); ++ return de; ++} ++ ++// Can be called from irq context ++static void dec_env_delete(struct rpivid_dec_env *const de) ++{ ++ struct rpivid_ctx * const ctx = de->ctx; ++ unsigned long lock_flags; ++ ++ aux_q_release(ctx, &de->frame_aux); ++ aux_q_release(ctx, &de->col_aux); ++ ++ spin_lock_irqsave(&ctx->dec_lock, lock_flags); ++ ++ de->state = RPIVID_DECODE_END; ++ de->next = ctx->dec_free; ++ ctx->dec_free = de; ++ ++ spin_unlock_irqrestore(&ctx->dec_lock, lock_flags); ++} ++ ++static void dec_env_uninit(struct rpivid_ctx *const ctx) ++{ ++ unsigned int i; ++ ++ if (ctx->dec_pool) { ++ for (i = 0; i != RPIVID_DEC_ENV_COUNT; ++i) { ++ struct rpivid_dec_env *const de = ctx->dec_pool + i; ++ ++ kfree(de->cmd_fifo); ++ } ++ ++ kfree(ctx->dec_pool); ++ } ++ ++ ctx->dec_pool = NULL; ++ ctx->dec_free = NULL; ++} ++ ++static int dec_env_init(struct rpivid_ctx *const ctx) ++{ ++ unsigned int i; ++ ++ ctx->dec_pool = kzalloc(sizeof(*ctx->dec_pool) * RPIVID_DEC_ENV_COUNT, ++ GFP_KERNEL); ++ if (!ctx->dec_pool) ++ return -1; ++ ++ spin_lock_init(&ctx->dec_lock); ++ ++ // Build free chain ++ ctx->dec_free = ctx->dec_pool; ++ for (i = 0; i != RPIVID_DEC_ENV_COUNT - 1; ++i) ++ ctx->dec_pool[i].next = ctx->dec_pool + i + 1; ++ ++ // Fill in other bits ++ for (i = 0; i != RPIVID_DEC_ENV_COUNT; ++i) { ++ struct rpivid_dec_env *const de = ctx->dec_pool + i; ++ ++ de->ctx = ctx; ++ de->decode_order = i; ++ de->cmd_max = 1024; ++ de->cmd_fifo = kmalloc_array(de->cmd_max, ++ sizeof(struct rpi_cmd), ++ GFP_KERNEL); ++ if (!de->cmd_fifo) ++ goto fail; ++ } ++ ++ return 0; ++ ++fail: ++ dec_env_uninit(ctx); ++ return -1; ++} ++ ++// Assume that we get exactly the same DPB for every slice ++// it makes no real sense otherwise ++#if V4L2_HEVC_DPB_ENTRIES_NUM_MAX > 16 ++#error HEVC_DPB_ENTRIES > h/w slots ++#endif ++ ++static u32 mk_config2(const struct rpivid_dec_state *const s) ++{ ++ const struct v4l2_ctrl_hevc_sps *const sps = &s->sps; ++ const struct v4l2_ctrl_hevc_pps *const pps = &s->pps; ++ u32 c; ++ // BitDepthY ++ c = (sps->bit_depth_luma_minus8 + 8) << 0; ++ // BitDepthC ++ c |= (sps->bit_depth_chroma_minus8 + 8) << 4; ++ // BitDepthY ++ if (sps->bit_depth_luma_minus8) ++ c |= BIT(8); ++ // BitDepthC ++ if (sps->bit_depth_chroma_minus8) ++ c |= BIT(9); ++ c |= s->log2_ctb_size << 10; ++ if (pps->flags & V4L2_HEVC_PPS_FLAG_CONSTRAINED_INTRA_PRED) ++ c |= BIT(13); ++ if (sps->flags & V4L2_HEVC_SPS_FLAG_STRONG_INTRA_SMOOTHING_ENABLED) ++ c |= BIT(14); ++ if (sps->flags & V4L2_HEVC_SPS_FLAG_SPS_TEMPORAL_MVP_ENABLED) ++ c |= BIT(15); /* Write motion vectors to external memory */ ++ c |= (pps->log2_parallel_merge_level_minus2 + 2) << 16; ++ if (s->slice_temporal_mvp) ++ c |= BIT(19); ++ if (sps->flags & V4L2_HEVC_SPS_FLAG_PCM_LOOP_FILTER_DISABLED) ++ c |= BIT(20); ++ c |= (pps->pps_cb_qp_offset & 31) << 21; ++ c |= (pps->pps_cr_qp_offset & 31) << 26; ++ return c; ++} ++ ++static void rpivid_h265_setup(struct rpivid_ctx *ctx, struct rpivid_run *run) ++{ ++ struct rpivid_dev *const dev = ctx->dev; ++ const struct v4l2_ctrl_hevc_slice_params *const sh = ++ run->h265.slice_params; ++ const struct v4l2_hevc_pred_weight_table *pred_weight_table; ++ struct rpivid_q_aux *dpb_q_aux[V4L2_HEVC_DPB_ENTRIES_NUM_MAX]; ++ struct rpivid_dec_state *const s = ctx->state; ++ struct vb2_queue *vq; ++ struct rpivid_dec_env *de; ++ int ctb_addr_ts; ++ unsigned int i; ++ int use_aux; ++ bool slice_temporal_mvp; ++ ++ pred_weight_table = &sh->pred_weight_table; ++ ++ s->frame_end = ++ ((run->src->flags & V4L2_BUF_FLAG_M2M_HOLD_CAPTURE_BUF) == 0); ++ ++ de = ctx->dec0; ++ slice_temporal_mvp = (sh->flags & ++ V4L2_HEVC_SLICE_PARAMS_FLAG_SLICE_TEMPORAL_MVP_ENABLED); ++ ++ if (de && de->state != RPIVID_DECODE_END) { ++ ++s->slice_idx; ++ ++ switch (de->state) { ++ case RPIVID_DECODE_SLICE_CONTINUE: ++ // Expected state ++ break; ++ default: ++ v4l2_err(&dev->v4l2_dev, "%s: Unexpected state: %d\n", ++ __func__, de->state); ++ /* FALLTHRU */ ++ case RPIVID_DECODE_ERROR_CONTINUE: ++ // Uncleared error - fail now ++ goto fail; ++ } ++ ++ if (s->slice_temporal_mvp != slice_temporal_mvp) { ++ v4l2_warn(&dev->v4l2_dev, ++ "Slice Temporal MVP non-constant\n"); ++ goto fail; ++ } ++ } else { ++ /* Frame start */ ++ unsigned int ctb_size_y; ++ bool sps_changed = false; ++ ++ if (memcmp(&s->sps, run->h265.sps, sizeof(s->sps)) != 0) { ++ /* SPS changed */ ++ v4l2_info(&dev->v4l2_dev, "SPS changed\n"); ++ memcpy(&s->sps, run->h265.sps, sizeof(s->sps)); ++ sps_changed = true; ++ } ++ if (sps_changed || ++ memcmp(&s->pps, run->h265.pps, sizeof(s->pps)) != 0) { ++ /* SPS changed */ ++ v4l2_info(&dev->v4l2_dev, "PPS changed\n"); ++ memcpy(&s->pps, run->h265.pps, sizeof(s->pps)); ++ ++ /* Recalc stuff as required */ ++ updated_ps(s); ++ } ++ ++ de = dec_env_new(ctx); ++ if (!de) { ++ v4l2_err(&dev->v4l2_dev, ++ "Failed to find free decode env\n"); ++ goto fail; ++ } ++ ctx->dec0 = de; ++ ++ ctb_size_y = ++ 1U << (s->sps.log2_min_luma_coding_block_size_minus3 + ++ 3 + ++ s->sps.log2_diff_max_min_luma_coding_block_size); ++ ++ de->pic_width_in_ctbs_y = ++ (s->sps.pic_width_in_luma_samples + ctb_size_y - 1) / ++ ctb_size_y; // 7-15 ++ de->pic_height_in_ctbs_y = ++ (s->sps.pic_height_in_luma_samples + ctb_size_y - 1) / ++ ctb_size_y; // 7-17 ++ de->cmd_len = 0; ++ de->dpbno_col = ~0U; ++ ++ de->bit_copy_gptr = ctx->bitbufs + 0; ++ de->bit_copy_len = 0; ++ de->cmd_copy_gptr = ctx->cmdbufs + 0; ++ ++ de->frame_c_offset = ctx->dst_fmt.height * 128; ++ de->frame_stride = ctx->dst_fmt.bytesperline * 128; ++ de->frame_addr = ++ vb2_dma_contig_plane_dma_addr(&run->dst->vb2_buf, 0); ++ de->frame_aux = NULL; ++ ++ if (s->sps.bit_depth_luma_minus8 != ++ s->sps.bit_depth_chroma_minus8) { ++ v4l2_warn(&dev->v4l2_dev, ++ "Chroma depth (%d) != Luma depth (%d)\n", ++ s->sps.bit_depth_chroma_minus8 + 8, ++ s->sps.bit_depth_luma_minus8 + 8); ++ goto fail; ++ } ++ if (s->sps.bit_depth_luma_minus8 == 0) { ++ if (ctx->dst_fmt.pixelformat != ++ V4L2_PIX_FMT_NV12_COL128) { ++ v4l2_err(&dev->v4l2_dev, ++ "Pixel format %#x != NV12_COL128 for 8-bit output", ++ ctx->dst_fmt.pixelformat); ++ goto fail; ++ } ++ } else if (s->sps.bit_depth_luma_minus8 == 2) { ++ if (ctx->dst_fmt.pixelformat != ++ V4L2_PIX_FMT_NV12_10_COL128) { ++ v4l2_err(&dev->v4l2_dev, ++ "Pixel format %#x != NV12_10_COL128 for 10-bit output", ++ ctx->dst_fmt.pixelformat); ++ goto fail; ++ } ++ } else { ++ v4l2_warn(&dev->v4l2_dev, ++ "Luma depth (%d) unsupported\n", ++ s->sps.bit_depth_luma_minus8 + 8); ++ goto fail; ++ } ++ if (run->dst->vb2_buf.num_planes != 1) { ++ v4l2_warn(&dev->v4l2_dev, "Capture planes (%d) != 1\n", ++ run->dst->vb2_buf.num_planes); ++ goto fail; ++ } ++ if (run->dst->planes[0].length < ++ ctx->dst_fmt.sizeimage) { ++ v4l2_warn(&dev->v4l2_dev, ++ "Capture plane[0] length (%d) < sizeimage (%d)\n", ++ run->dst->planes[0].length, ++ ctx->dst_fmt.sizeimage); ++ goto fail; ++ } ++ ++ if (s->sps.pic_width_in_luma_samples > 4096 || ++ s->sps.pic_height_in_luma_samples > 4096) { ++ v4l2_warn(&dev->v4l2_dev, ++ "Pic dimension (%dx%d) exeeds 4096\n", ++ s->sps.pic_width_in_luma_samples, ++ s->sps.pic_height_in_luma_samples); ++ goto fail; ++ } ++ ++ // Fill in ref planes with our address s.t. if we mess ++ // up refs somehow then we still have a valid address ++ // entry ++ for (i = 0; i != 16; ++i) ++ de->ref_addrs[i] = de->frame_addr; ++ ++ /* ++ * Stash initial temporal_mvp flag ++ * This must be the same for all pic slices (7.4.7.1) ++ */ ++ s->slice_temporal_mvp = slice_temporal_mvp; ++ ++ // Phase 2 reg pre-calc ++ de->rpi_config2 = mk_config2(s); ++ de->rpi_framesize = (s->sps.pic_height_in_luma_samples << 16) | ++ s->sps.pic_width_in_luma_samples; ++ de->rpi_currpoc = sh->slice_pic_order_cnt; ++ ++ if (s->sps.flags & ++ V4L2_HEVC_SPS_FLAG_SPS_TEMPORAL_MVP_ENABLED) { ++ setup_colmv(ctx, run, s); ++ } ++ ++ s->slice_idx = 0; ++ ++ if (sh->slice_segment_addr != 0) { ++ v4l2_warn(&dev->v4l2_dev, ++ "New frame but segment_addr=%d\n", ++ sh->slice_segment_addr); ++ goto fail; ++ } ++ ++ /* Allocate a bitbuf if we need one - don't need one if single ++ * slice as we can use the src buf directly ++ */ ++ if (!s->frame_end && !de->bit_copy_gptr->ptr) { ++ const size_t wxh = s->sps.pic_width_in_luma_samples * ++ s->sps.pic_height_in_luma_samples; ++ size_t bits_alloc; ++ ++ /* Annex A gives a min compression of 2 @ lvl 3.1 ++ * (wxh <= 983040) and min 4 thereafter but avoid ++ * the odity of 983041 having a lower limit than ++ * 983040. ++ * Multiply by 3/2 for 4:2:0 ++ */ ++ bits_alloc = wxh < 983040 ? wxh * 3 / 4 : ++ wxh < 983040 * 2 ? 983040 * 3 / 4 : ++ wxh * 3 / 8; ++ bits_alloc = round_up_size(bits_alloc); ++ ++ if (gptr_alloc(dev, de->bit_copy_gptr, ++ bits_alloc, ++ DMA_ATTR_FORCE_CONTIGUOUS) != 0) { ++ v4l2_err(&dev->v4l2_dev, ++ "Unable to alloc buf (%d) for bit copy\n", ++ bits_alloc); ++ goto fail; ++ } ++ v4l2_info(&dev->v4l2_dev, ++ "Alloc buf (%d) for bit copy OK\n", ++ bits_alloc); ++ } ++ } ++ ++ // Pre calc a few things ++ s->src_addr = ++ !s->frame_end ? ++ 0 : ++ vb2_dma_contig_plane_dma_addr(&run->src->vb2_buf, 0); ++ s->src_buf = s->src_addr != 0 ? NULL : ++ vb2_plane_vaddr(&run->src->vb2_buf, 0); ++ if (!s->src_addr && !s->src_buf) { ++ v4l2_err(&dev->v4l2_dev, "Failed to map src buffer\n"); ++ goto fail; ++ } ++ ++ s->sh = sh; ++ s->slice_qp = 26 + s->pps.init_qp_minus26 + s->sh->slice_qp_delta; ++ s->max_num_merge_cand = sh->slice_type == HEVC_SLICE_I ? ++ 0 : ++ (5 - sh->five_minus_max_num_merge_cand); ++ // * SH DSS flag invented by me - but clearly needed ++ s->dependent_slice_segment_flag = ++ ((sh->flags & ++ V4L2_HEVC_SLICE_PARAMS_FLAG_DEPENDENT_SLICE_SEGMENT) != 0); ++ ++ s->nb_refs[0] = (sh->slice_type == HEVC_SLICE_I) ? ++ 0 : ++ sh->num_ref_idx_l0_active_minus1 + 1; ++ s->nb_refs[1] = (sh->slice_type != HEVC_SLICE_B) ? ++ 0 : ++ sh->num_ref_idx_l1_active_minus1 + 1; ++ ++ if (s->sps.flags & V4L2_HEVC_SPS_FLAG_SCALING_LIST_ENABLED) ++ populate_scaling_factors(run, de, s); ++ ++ ctb_addr_ts = s->ctb_addr_rs_to_ts[sh->slice_segment_addr]; ++ ++ if ((s->pps.flags & V4L2_HEVC_PPS_FLAG_ENTROPY_CODING_SYNC_ENABLED)) ++ wpp_decode_slice(de, s, sh, ctb_addr_ts); ++ else ++ decode_slice(de, s, sh, ctb_addr_ts); ++ ++ if (!s->frame_end) ++ return; ++ ++ // Frame end ++ memset(dpb_q_aux, 0, ++ sizeof(*dpb_q_aux) * V4L2_HEVC_DPB_ENTRIES_NUM_MAX); ++ /* ++ * Need Aux ents for all (ref) DPB ents if temporal MV could ++ * be enabled for any pic ++ * ** At the moment we have aux ents for all pics whether or not ++ * they are ref ++ */ ++ use_aux = ((s->sps.flags & ++ V4L2_HEVC_SPS_FLAG_SPS_TEMPORAL_MVP_ENABLED) != 0); ++ ++ // Locate ref frames ++ // At least in the current implementation this is constant across all ++ // slices. If this changes we will need idx mapping code. ++ // Uses sh so here rather than trigger ++ ++ vq = v4l2_m2m_get_vq(ctx->fh.m2m_ctx, V4L2_BUF_TYPE_VIDEO_CAPTURE); ++ ++ if (!vq) { ++ v4l2_err(&dev->v4l2_dev, "VQ gone!\n"); ++ goto fail; ++ } ++ ++ // v4l2_info(&dev->v4l2_dev, "rpivid_h265_end of frame\n"); ++ if (frame_end(dev, de, s)) ++ goto fail; ++ ++ for (i = 0; i < sh->num_active_dpb_entries; ++i) { ++ int buffer_index = ++ vb2_find_timestamp(vq, sh->dpb[i].timestamp, 0); ++ struct vb2_buffer *buf = buffer_index < 0 ? ++ NULL : ++ vb2_get_buffer(vq, buffer_index); ++ ++ if (!buf) { ++ v4l2_warn(&dev->v4l2_dev, ++ "Missing DPB ent %d, timestamp=%lld, index=%d\n", ++ i, (long long)sh->dpb[i].timestamp, ++ buffer_index); ++ continue; ++ } ++ ++ if (use_aux) { ++ dpb_q_aux[i] = aux_q_ref(ctx, ++ ctx->aux_ents[buffer_index]); ++ if (!dpb_q_aux[i]) ++ v4l2_warn(&dev->v4l2_dev, ++ "Missing DPB AUX ent %d index=%d\n", ++ i, buffer_index); ++ } ++ ++ de->ref_addrs[i] = ++ vb2_dma_contig_plane_dma_addr(buf, 0); ++ } ++ ++ // Move DPB from temp ++ for (i = 0; i != V4L2_HEVC_DPB_ENTRIES_NUM_MAX; ++i) { ++ aux_q_release(ctx, &s->ref_aux[i]); ++ s->ref_aux[i] = dpb_q_aux[i]; ++ } ++ // Unref the old frame aux too - it is either in the DPB or not ++ // now ++ aux_q_release(ctx, &s->frame_aux); ++ ++ if (use_aux) { ++ // New frame so new aux ent ++ // ??? Do we need this if non-ref ??? can we tell ++ s->frame_aux = aux_q_new(ctx, run->dst->vb2_buf.index); ++ ++ if (!s->frame_aux) { ++ v4l2_err(&dev->v4l2_dev, ++ "Failed to obtain aux storage for frame\n"); ++ goto fail; ++ } ++ ++ de->frame_aux = aux_q_ref(ctx, s->frame_aux); ++ } ++ ++ if (de->dpbno_col != ~0U) { ++ if (de->dpbno_col >= sh->num_active_dpb_entries) { ++ v4l2_err(&dev->v4l2_dev, ++ "Col ref index %d >= %d\n", ++ de->dpbno_col, ++ sh->num_active_dpb_entries); ++ } else { ++ // Standard requires that the col pic is ++ // constant for the duration of the pic ++ // (text of collocated_ref_idx in H265-2 2018 ++ // 7.4.7.1) ++ ++ // Spot the collocated ref in passing ++ de->col_aux = aux_q_ref(ctx, ++ dpb_q_aux[de->dpbno_col]); ++ ++ if (!de->col_aux) { ++ v4l2_warn(&dev->v4l2_dev, ++ "Missing DPB ent for col\n"); ++ // Probably need to abort if this fails ++ // as P2 may explode on bad data ++ goto fail; ++ } ++ } ++ } ++ ++ de->state = RPIVID_DECODE_PHASE1; ++ return; ++ ++fail: ++ if (de) ++ // Actual error reporting happens in Trigger ++ de->state = s->frame_end ? RPIVID_DECODE_ERROR_DONE : ++ RPIVID_DECODE_ERROR_CONTINUE; ++} ++ ++////////////////////////////////////////////////////////////////////////////// ++// Handle PU and COEFF stream overflow ++ ++// Returns: ++// -1 Phase 1 decode error ++// 0 OK ++// >0 Out of space (bitmask) ++ ++#define STATUS_COEFF_EXHAUSTED 8 ++#define STATUS_PU_EXHAUSTED 16 ++ ++static int check_status(const struct rpivid_dev *const dev) ++{ ++ const u32 cfstatus = apb_read(dev, RPI_CFSTATUS); ++ const u32 cfnum = apb_read(dev, RPI_CFNUM); ++ u32 status = apb_read(dev, RPI_STATUS); ++ ++ // Handle PU and COEFF stream overflow ++ ++ // this is the definition of successful completion of phase 1 ++ // it assures that status register is zero and all blocks in each tile ++ // have completed ++ if (cfstatus == cfnum) ++ return 0; //No error ++ ++ status &= (STATUS_PU_EXHAUSTED | STATUS_COEFF_EXHAUSTED); ++ if (status) ++ return status; ++ ++ return -1; ++} ++ ++static void cb_phase2(struct rpivid_dev *const dev, void *v) ++{ ++ struct rpivid_dec_env *const de = v; ++ struct rpivid_ctx *const ctx = de->ctx; ++ ++ xtrace_in(dev, de); ++ ++ v4l2_m2m_cap_buf_return(dev->m2m_dev, ctx->fh.m2m_ctx, de->frame_buf, ++ VB2_BUF_STATE_DONE); ++ de->frame_buf = NULL; ++ ++ /* Delete de before finish as finish might immediately trigger a reuse ++ * of de ++ */ ++ dec_env_delete(de); ++ ++ if (atomic_add_return(-1, &ctx->p2out) >= RPIVID_P2BUF_COUNT - 1) { ++ xtrace_fin(dev, de); ++ v4l2_m2m_buf_done_and_job_finish(dev->m2m_dev, ctx->fh.m2m_ctx, ++ VB2_BUF_STATE_DONE); ++ } ++ ++ xtrace_ok(dev, de); ++} ++ ++static void phase2_claimed(struct rpivid_dev *const dev, void *v) ++{ ++ struct rpivid_dec_env *const de = v; ++ unsigned int i; ++ ++ xtrace_in(dev, de); ++ ++ apb_write_vc_addr(dev, RPI_PURBASE, de->pu_base_vc); ++ apb_write_vc_len(dev, RPI_PURSTRIDE, de->pu_stride); ++ apb_write_vc_addr(dev, RPI_COEFFRBASE, de->coeff_base_vc); ++ apb_write_vc_len(dev, RPI_COEFFRSTRIDE, de->coeff_stride); ++ ++ apb_write_vc_addr(dev, RPI_OUTYBASE, de->frame_addr); ++ apb_write_vc_addr(dev, RPI_OUTCBASE, ++ de->frame_addr + de->frame_c_offset); ++ apb_write_vc_len(dev, RPI_OUTYSTRIDE, de->frame_stride); ++ apb_write_vc_len(dev, RPI_OUTCSTRIDE, de->frame_stride); ++ ++ // v4l2_info(&dev->v4l2_dev, "Frame: Y=%llx, C=%llx, Stride=%x\n", ++ // de->frame_addr, de->frame_addr + de->frame_c_offset, ++ // de->frame_stride); ++ ++ for (i = 0; i < 16; i++) { ++ // Strides are in fact unused but fill in anyway ++ apb_write_vc_addr(dev, 0x9000 + 16 * i, de->ref_addrs[i]); ++ apb_write_vc_len(dev, 0x9004 + 16 * i, de->frame_stride); ++ apb_write_vc_addr(dev, 0x9008 + 16 * i, ++ de->ref_addrs[i] + de->frame_c_offset); ++ apb_write_vc_len(dev, 0x900C + 16 * i, de->frame_stride); ++ } ++ ++ apb_write(dev, RPI_CONFIG2, de->rpi_config2); ++ apb_write(dev, RPI_FRAMESIZE, de->rpi_framesize); ++ apb_write(dev, RPI_CURRPOC, de->rpi_currpoc); ++ // v4l2_info(&dev->v4l2_dev, "Config2=%#x, FrameSize=%#x, POC=%#x\n", ++ // de->rpi_config2, de->rpi_framesize, de->rpi_currpoc); ++ ++ // collocated reads/writes ++ apb_write_vc_len(dev, RPI_COLSTRIDE, ++ de->ctx->colmv_stride); // Read vals ++ apb_write_vc_len(dev, RPI_MVSTRIDE, ++ de->ctx->colmv_stride); // Write vals ++ apb_write_vc_addr(dev, RPI_MVBASE, ++ !de->frame_aux ? 0 : de->frame_aux->col.addr); ++ apb_write_vc_addr(dev, RPI_COLBASE, ++ !de->col_aux ? 0 : de->col_aux->col.addr); ++ ++ //v4l2_info(&dev->v4l2_dev, ++ // "Mv=%llx, Col=%llx, Stride=%x, Buf=%llx->%llx\n", ++ // de->rpi_mvbase, de->rpi_colbase, de->ctx->colmv_stride, ++ // de->ctx->colmvbuf.addr, de->ctx->colmvbuf.addr + ++ // de->ctx->colmvbuf.size); ++ ++ rpivid_hw_irq_active2_irq(dev, &de->irq_ent, cb_phase2, de); ++ ++ apb_write_final(dev, RPI_NUMROWS, de->pic_height_in_ctbs_y); ++ ++ xtrace_ok(dev, de); ++} ++ ++static void phase1_claimed(struct rpivid_dev *const dev, void *v); ++ ++static void phase1_thread(struct rpivid_dev *const dev, void *v) ++{ ++ struct rpivid_dec_env *const de = v; ++ struct rpivid_ctx *const ctx = de->ctx; ++ ++ struct rpivid_gptr *const pu_gptr = ctx->pu_bufs + ctx->p2idx; ++ struct rpivid_gptr *const coeff_gptr = ctx->coeff_bufs + ctx->p2idx; ++ ++ xtrace_in(dev, de); ++ ++ if (de->p1_status & STATUS_PU_EXHAUSTED) { ++ if (gptr_realloc_new(dev, pu_gptr, next_size(pu_gptr->size))) { ++ v4l2_err(&dev->v4l2_dev, ++ "%s: PU realloc (%#x) failed\n", ++ __func__, pu_gptr->size); ++ goto fail; ++ } ++ v4l2_info(&dev->v4l2_dev, "%s: PU realloc (%#x) OK\n", ++ __func__, pu_gptr->size); ++ } ++ ++ if (de->p1_status & STATUS_COEFF_EXHAUSTED) { ++ if (gptr_realloc_new(dev, coeff_gptr, ++ next_size(coeff_gptr->size))) { ++ v4l2_err(&dev->v4l2_dev, ++ "%s: Coeff realloc (%#x) failed\n", ++ __func__, coeff_gptr->size); ++ goto fail; ++ } ++ v4l2_info(&dev->v4l2_dev, "%s: Coeff realloc (%#x) OK\n", ++ __func__, coeff_gptr->size); ++ } ++ ++ phase1_claimed(dev, de); ++ xtrace_ok(dev, de); ++ return; ++ ++fail: ++ dec_env_delete(de); ++ xtrace_fin(dev, de); ++ v4l2_m2m_buf_done_and_job_finish(dev->m2m_dev, ctx->fh.m2m_ctx, ++ VB2_BUF_STATE_ERROR); ++ xtrace_fail(dev, de); ++} ++ ++/* Always called in irq context (this is good) */ ++static void cb_phase1(struct rpivid_dev *const dev, void *v) ++{ ++ struct rpivid_dec_env *const de = v; ++ struct rpivid_ctx *const ctx = de->ctx; ++ ++ xtrace_in(dev, de); ++ ++ de->p1_status = check_status(dev); ++ if (de->p1_status != 0) { ++ v4l2_info(&dev->v4l2_dev, "%s: Post wait: %#x\n", ++ __func__, de->p1_status); ++ ++ if (de->p1_status < 0) ++ goto fail; ++ ++ /* Need to realloc - push onto a thread rather than IRQ */ ++ rpivid_hw_irq_active1_thread(dev, &de->irq_ent, ++ phase1_thread, de); ++ return; ++ } ++ ++ /* After the frame-buf is detached it must be returned but from ++ * this point onward (phase2_claimed, cb_phase2) there are no error ++ * paths so the return at the end of cb_phase2 is all that is needed ++ */ ++ de->frame_buf = v4l2_m2m_cap_buf_detach(dev->m2m_dev, ctx->fh.m2m_ctx); ++ if (!de->frame_buf) { ++ v4l2_err(&dev->v4l2_dev, "%s: No detached buffer\n", __func__); ++ goto fail; ++ } ++ ++ ctx->p2idx = ++ (ctx->p2idx + 1 >= RPIVID_P2BUF_COUNT) ? 0 : ctx->p2idx + 1; ++ ++ // Enable the next setup if our Q isn't too big ++ if (atomic_add_return(1, &ctx->p2out) < RPIVID_P2BUF_COUNT) { ++ xtrace_fin(dev, de); ++ v4l2_m2m_buf_done_and_job_finish(dev->m2m_dev, ctx->fh.m2m_ctx, ++ VB2_BUF_STATE_DONE); ++ } ++ ++ rpivid_hw_irq_active2_claim(dev, &de->irq_ent, phase2_claimed, de); ++ ++ xtrace_ok(dev, de); ++ return; ++ ++fail: ++ dec_env_delete(de); ++ xtrace_fin(dev, de); ++ v4l2_m2m_buf_done_and_job_finish(dev->m2m_dev, ctx->fh.m2m_ctx, ++ VB2_BUF_STATE_ERROR); ++ xtrace_fail(dev, de); ++} ++ ++static void phase1_claimed(struct rpivid_dev *const dev, void *v) ++{ ++ struct rpivid_dec_env *const de = v; ++ struct rpivid_ctx *const ctx = de->ctx; ++ ++ const struct rpivid_gptr * const pu_gptr = ctx->pu_bufs + ctx->p2idx; ++ const struct rpivid_gptr * const coeff_gptr = ctx->coeff_bufs + ++ ctx->p2idx; ++ ++ xtrace_in(dev, de); ++ ++ de->pu_base_vc = pu_gptr->addr; ++ de->pu_stride = ++ ALIGN_DOWN(pu_gptr->size / de->pic_height_in_ctbs_y, 64); ++ ++ de->coeff_base_vc = coeff_gptr->addr; ++ de->coeff_stride = ++ ALIGN_DOWN(coeff_gptr->size / de->pic_height_in_ctbs_y, 64); ++ ++ apb_write_vc_addr(dev, RPI_PUWBASE, de->pu_base_vc); ++ apb_write_vc_len(dev, RPI_PUWSTRIDE, de->pu_stride); ++ apb_write_vc_addr(dev, RPI_COEFFWBASE, de->coeff_base_vc); ++ apb_write_vc_len(dev, RPI_COEFFWSTRIDE, de->coeff_stride); ++ ++ // Trigger command FIFO ++ apb_write(dev, RPI_CFNUM, de->cmd_len); ++ ++ // Claim irq ++ rpivid_hw_irq_active1_irq(dev, &de->irq_ent, cb_phase1, de); ++ ++ // And start the h/w ++ apb_write_vc_addr_final(dev, RPI_CFBASE, de->cmd_copy_gptr->addr); ++ ++ xtrace_ok(dev, de); ++} ++ ++static void dec_state_delete(struct rpivid_ctx *const ctx) ++{ ++ unsigned int i; ++ struct rpivid_dec_state *const s = ctx->state; ++ ++ if (!s) ++ return; ++ ctx->state = NULL; ++ ++ free_ps_info(s); ++ ++ for (i = 0; i != HEVC_MAX_REFS; ++i) ++ aux_q_release(ctx, &s->ref_aux[i]); ++ aux_q_release(ctx, &s->frame_aux); ++ ++ kfree(s); ++} ++ ++static void rpivid_h265_stop(struct rpivid_ctx *ctx) ++{ ++ struct rpivid_dev *const dev = ctx->dev; ++ unsigned int i; ++ ++ v4l2_info(&dev->v4l2_dev, "%s\n", __func__); ++ ++ dec_env_uninit(ctx); ++ dec_state_delete(ctx); ++ ++ // dec_env & state must be killed before this to release the buffer to ++ // the free pool ++ aux_q_uninit(ctx); ++ ++ for (i = 0; i != ARRAY_SIZE(ctx->bitbufs); ++i) ++ gptr_free(dev, ctx->bitbufs + i); ++ for (i = 0; i != ARRAY_SIZE(ctx->cmdbufs); ++i) ++ gptr_free(dev, ctx->cmdbufs + i); ++ for (i = 0; i != ARRAY_SIZE(ctx->pu_bufs); ++i) ++ gptr_free(dev, ctx->pu_bufs + i); ++ for (i = 0; i != ARRAY_SIZE(ctx->coeff_bufs); ++i) ++ gptr_free(dev, ctx->coeff_bufs + i); ++} ++ ++static int rpivid_h265_start(struct rpivid_ctx *ctx) ++{ ++ struct rpivid_dev *const dev = ctx->dev; ++ unsigned int i; ++ ++ unsigned int w = ctx->dst_fmt.width; ++ unsigned int h = ctx->dst_fmt.height; ++ unsigned int wxh; ++ size_t pu_alloc; ++ size_t coeff_alloc; ++ ++ // Generate a sanitised WxH for memory alloc ++ // Assume HD if unset ++ if (w == 0) ++ w = 1920; ++ if (w > 4096) ++ w = 4096; ++ if (h == 0) ++ w = 1088; ++ if (h > 4096) ++ h = 4096; ++ wxh = w * h; ++ ++ v4l2_info(&dev->v4l2_dev, "%s: (%dx%d)\n", __func__, ++ ctx->dst_fmt.width, ctx->dst_fmt.height); ++ ++ ctx->dec0 = NULL; ++ ctx->state = kzalloc(sizeof(*ctx->state), GFP_KERNEL); ++ if (!ctx->state) { ++ v4l2_err(&dev->v4l2_dev, "Failed to allocate decode state\n"); ++ goto fail; ++ } ++ ++ if (dec_env_init(ctx) != 0) { ++ v4l2_err(&dev->v4l2_dev, "Failed to allocate decode envs\n"); ++ goto fail; ++ } ++ ++ // 16k is plenty for most purposes but we will realloc if needed ++ for (i = 0; i != ARRAY_SIZE(ctx->cmdbufs); ++i) { ++ if (gptr_alloc(dev, ctx->cmdbufs + i, 0x4000, ++ DMA_ATTR_FORCE_CONTIGUOUS)) ++ goto fail; ++ } ++ ++ // Finger in the air PU & Coeff alloc ++ // Will be realloced if too small ++ coeff_alloc = round_up_size(wxh); ++ pu_alloc = round_up_size(wxh / 4); ++ for (i = 0; i != ARRAY_SIZE(ctx->pu_bufs); ++i) { ++ // Don't actually need a kernel mapping here ++ if (gptr_alloc(dev, ctx->pu_bufs + i, pu_alloc, ++ DMA_ATTR_FORCE_CONTIGUOUS | ++ DMA_ATTR_NO_KERNEL_MAPPING)) ++ goto fail; ++ if (gptr_alloc(dev, ctx->coeff_bufs + i, coeff_alloc, ++ DMA_ATTR_FORCE_CONTIGUOUS | ++ DMA_ATTR_NO_KERNEL_MAPPING)) ++ goto fail; ++ } ++ aux_q_init(ctx); ++ ++ return 0; ++ ++fail: ++ rpivid_h265_stop(ctx); ++ return -ENOMEM; ++} ++ ++static void rpivid_h265_trigger(struct rpivid_ctx *ctx) ++{ ++ struct rpivid_dev *const dev = ctx->dev; ++ struct rpivid_dec_env *const de = ctx->dec0; ++ ++ xtrace_in(dev, de); ++ ++ switch (!de ? RPIVID_DECODE_ERROR_CONTINUE : de->state) { ++ case RPIVID_DECODE_SLICE_START: ++ de->state = RPIVID_DECODE_SLICE_CONTINUE; ++ /* FALLTHRU */ ++ case RPIVID_DECODE_SLICE_CONTINUE: ++ v4l2_m2m_buf_done_and_job_finish(dev->m2m_dev, ctx->fh.m2m_ctx, ++ VB2_BUF_STATE_DONE); ++ break; ++ default: ++ v4l2_err(&dev->v4l2_dev, "%s: Unexpected state: %d\n", __func__, ++ de->state); ++ /* FALLTHRU */ ++ case RPIVID_DECODE_ERROR_DONE: ++ ctx->dec0 = NULL; ++ dec_env_delete(de); ++ /* FALLTHRU */ ++ case RPIVID_DECODE_ERROR_CONTINUE: ++ xtrace_fin(dev, de); ++ v4l2_m2m_buf_done_and_job_finish(dev->m2m_dev, ctx->fh.m2m_ctx, ++ VB2_BUF_STATE_ERROR); ++ break; ++ case RPIVID_DECODE_PHASE1: ++ ctx->dec0 = NULL; ++ rpivid_hw_irq_active1_claim(dev, &de->irq_ent, phase1_claimed, ++ de); ++ break; ++ } ++ ++ xtrace_ok(dev, de); ++} ++ ++struct rpivid_dec_ops rpivid_dec_ops_h265 = { ++ .setup = rpivid_h265_setup, ++ .start = rpivid_h265_start, ++ .stop = rpivid_h265_stop, ++ .trigger = rpivid_h265_trigger, ++}; +--- /dev/null ++++ b/drivers/staging/media/rpivid/rpivid_hw.c +@@ -0,0 +1,321 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * Raspberry Pi HEVC driver ++ * ++ * Copyright (C) 2020 Raspberry Pi (Trading) Ltd ++ * ++ * Based on the Cedrus VPU driver, that is: ++ * ++ * Copyright (C) 2016 Florent Revest ++ * Copyright (C) 2018 Paul Kocialkowski ++ * Copyright (C) 2018 Bootlin ++ */ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++ ++#include "rpivid.h" ++#include "rpivid_hw.h" ++ ++static void pre_irq(struct rpivid_dev *dev, struct rpivid_hw_irq_ent *ient, ++ rpivid_irq_callback cb, void *v, ++ struct rpivid_hw_irq_ctrl *ictl) ++{ ++ unsigned long flags; ++ ++ if (ictl->irq) { ++ v4l2_err(&dev->v4l2_dev, "Attempt to claim IRQ when already claimed\n"); ++ return; ++ } ++ ++ ient->cb = cb; ++ ient->v = v; ++ ++ // Not sure this lock is actually required ++ spin_lock_irqsave(&ictl->lock, flags); ++ ictl->irq = ient; ++ spin_unlock_irqrestore(&ictl->lock, flags); ++} ++ ++static void sched_claim(struct rpivid_dev * const dev, ++ struct rpivid_hw_irq_ctrl * const ictl) ++{ ++ for (;;) { ++ struct rpivid_hw_irq_ent *ient = NULL; ++ unsigned long flags; ++ ++ spin_lock_irqsave(&ictl->lock, flags); ++ ++ if (--ictl->no_sched <= 0) { ++ ient = ictl->claim; ++ if (!ictl->irq && ient) { ++ ictl->claim = ient->next; ++ ictl->no_sched = 1; ++ } ++ } ++ ++ spin_unlock_irqrestore(&ictl->lock, flags); ++ ++ if (!ient) ++ break; ++ ++ ient->cb(dev, ient->v); ++ } ++} ++ ++/* Should only ever be called from its own IRQ cb so no lock required */ ++static void pre_thread(struct rpivid_dev *dev, ++ struct rpivid_hw_irq_ent *ient, ++ rpivid_irq_callback cb, void *v, ++ struct rpivid_hw_irq_ctrl *ictl) ++{ ++ ient->cb = cb; ++ ient->v = v; ++ ictl->irq = ient; ++ ictl->thread_reqed = true; ++ ictl->no_sched++; ++} ++ ++// Called in irq context ++static void do_irq(struct rpivid_dev * const dev, ++ struct rpivid_hw_irq_ctrl * const ictl) ++{ ++ struct rpivid_hw_irq_ent *ient; ++ unsigned long flags; ++ ++ spin_lock_irqsave(&ictl->lock, flags); ++ ient = ictl->irq; ++ if (ient) { ++ ictl->no_sched++; ++ ictl->irq = NULL; ++ } ++ spin_unlock_irqrestore(&ictl->lock, flags); ++ ++ if (ient) { ++ ient->cb(dev, ient->v); ++ ++ sched_claim(dev, ictl); ++ } ++} ++ ++static void do_claim(struct rpivid_dev * const dev, ++ struct rpivid_hw_irq_ent *ient, ++ const rpivid_irq_callback cb, void * const v, ++ struct rpivid_hw_irq_ctrl * const ictl) ++{ ++ unsigned long flags; ++ ++ ient->next = NULL; ++ ient->cb = cb; ++ ient->v = v; ++ ++ spin_lock_irqsave(&ictl->lock, flags); ++ ++ if (ictl->claim) { ++ // If we have a Q then add to end ++ ictl->tail->next = ient; ++ ictl->tail = ient; ++ ient = NULL; ++ } else if (ictl->no_sched || ictl->irq) { ++ // Empty Q but other activity in progress so Q ++ ictl->claim = ient; ++ ictl->tail = ient; ++ ient = NULL; ++ } else { ++ // Nothing else going on - schedule immediately and ++ // prevent anything else scheduling claims ++ ictl->no_sched = 1; ++ } ++ ++ spin_unlock_irqrestore(&ictl->lock, flags); ++ ++ if (ient) { ++ ient->cb(dev, ient->v); ++ ++ sched_claim(dev, ictl); ++ } ++} ++ ++static void ictl_init(struct rpivid_hw_irq_ctrl * const ictl) ++{ ++ spin_lock_init(&ictl->lock); ++ ictl->claim = NULL; ++ ictl->tail = NULL; ++ ictl->irq = NULL; ++ ictl->no_sched = 0; ++} ++ ++static void ictl_uninit(struct rpivid_hw_irq_ctrl * const ictl) ++{ ++ // Nothing to do ++} ++ ++#if !OPT_DEBUG_POLL_IRQ ++static irqreturn_t rpivid_irq_irq(int irq, void *data) ++{ ++ struct rpivid_dev * const dev = data; ++ __u32 ictrl; ++ ++ ictrl = irq_read(dev, ARG_IC_ICTRL); ++ if (!(ictrl & ARG_IC_ICTRL_ALL_IRQ_MASK)) { ++ v4l2_warn(&dev->v4l2_dev, "IRQ but no IRQ bits set\n"); ++ return IRQ_NONE; ++ } ++ ++ // Cancel any/all irqs ++ irq_write(dev, ARG_IC_ICTRL, ictrl & ~ARG_IC_ICTRL_SET_ZERO_MASK); ++ ++ // Service Active2 before Active1 so Phase 1 can transition to Phase 2 ++ // without delay ++ if (ictrl & ARG_IC_ICTRL_ACTIVE2_INT_SET) ++ do_irq(dev, &dev->ic_active2); ++ if (ictrl & ARG_IC_ICTRL_ACTIVE1_INT_SET) ++ do_irq(dev, &dev->ic_active1); ++ ++ return dev->ic_active1.thread_reqed || dev->ic_active2.thread_reqed ? ++ IRQ_WAKE_THREAD : IRQ_HANDLED; ++} ++ ++static void do_thread(struct rpivid_dev * const dev, ++ struct rpivid_hw_irq_ctrl *const ictl) ++{ ++ unsigned long flags; ++ struct rpivid_hw_irq_ent *ient = NULL; ++ ++ spin_lock_irqsave(&ictl->lock, flags); ++ ++ if (ictl->thread_reqed) { ++ ient = ictl->irq; ++ ictl->thread_reqed = false; ++ ictl->irq = NULL; ++ } ++ ++ spin_unlock_irqrestore(&ictl->lock, flags); ++ ++ if (ient) { ++ ient->cb(dev, ient->v); ++ ++ sched_claim(dev, ictl); ++ } ++} ++ ++static irqreturn_t rpivid_irq_thread(int irq, void *data) ++{ ++ struct rpivid_dev * const dev = data; ++ ++ do_thread(dev, &dev->ic_active1); ++ do_thread(dev, &dev->ic_active2); ++ ++ return IRQ_HANDLED; ++} ++#endif ++ ++/* May only be called from Active1 CB ++ * IRQs should not be expected until execution continues in the cb ++ */ ++void rpivid_hw_irq_active1_thread(struct rpivid_dev *dev, ++ struct rpivid_hw_irq_ent *ient, ++ rpivid_irq_callback thread_cb, void *ctx) ++{ ++ pre_thread(dev, ient, thread_cb, ctx, &dev->ic_active1); ++} ++ ++void rpivid_hw_irq_active1_claim(struct rpivid_dev *dev, ++ struct rpivid_hw_irq_ent *ient, ++ rpivid_irq_callback ready_cb, void *ctx) ++{ ++ do_claim(dev, ient, ready_cb, ctx, &dev->ic_active1); ++} ++ ++void rpivid_hw_irq_active1_irq(struct rpivid_dev *dev, ++ struct rpivid_hw_irq_ent *ient, ++ rpivid_irq_callback irq_cb, void *ctx) ++{ ++ pre_irq(dev, ient, irq_cb, ctx, &dev->ic_active1); ++} ++ ++void rpivid_hw_irq_active2_claim(struct rpivid_dev *dev, ++ struct rpivid_hw_irq_ent *ient, ++ rpivid_irq_callback ready_cb, void *ctx) ++{ ++ do_claim(dev, ient, ready_cb, ctx, &dev->ic_active2); ++} ++ ++void rpivid_hw_irq_active2_irq(struct rpivid_dev *dev, ++ struct rpivid_hw_irq_ent *ient, ++ rpivid_irq_callback irq_cb, void *ctx) ++{ ++ pre_irq(dev, ient, irq_cb, ctx, &dev->ic_active2); ++} ++ ++int rpivid_hw_probe(struct rpivid_dev *dev) ++{ ++ struct resource *res; ++ __u32 irq_stat; ++ int irq_dec; ++ int ret = 0; ++ ++ ictl_init(&dev->ic_active1); ++ ictl_init(&dev->ic_active2); ++ ++ res = platform_get_resource_byname(dev->pdev, IORESOURCE_MEM, "intc"); ++ if (!res) ++ return -ENODEV; ++ ++ dev->base_irq = devm_ioremap(dev->dev, res->start, resource_size(res)); ++ if (IS_ERR(dev->base_irq)) ++ return PTR_ERR(dev->base_irq); ++ ++ res = platform_get_resource_byname(dev->pdev, IORESOURCE_MEM, "hevc"); ++ if (!res) ++ return -ENODEV; ++ ++ dev->base_h265 = devm_ioremap(dev->dev, res->start, resource_size(res)); ++ if (IS_ERR(dev->base_h265)) ++ return PTR_ERR(dev->base_h265); ++ ++ dev->clock = devm_clk_get(&dev->pdev->dev, "hevc"); ++ if (IS_ERR(dev->clock)) ++ return PTR_ERR(dev->clock); ++ ++ // Disable IRQs & reset anything pending ++ irq_write(dev, 0, ++ ARG_IC_ICTRL_ACTIVE1_EN_SET | ARG_IC_ICTRL_ACTIVE2_EN_SET); ++ irq_stat = irq_read(dev, 0); ++ irq_write(dev, 0, irq_stat); ++ ++#if !OPT_DEBUG_POLL_IRQ ++ irq_dec = platform_get_irq(dev->pdev, 0); ++ if (irq_dec <= 0) ++ return irq_dec; ++ ret = devm_request_threaded_irq(dev->dev, irq_dec, ++ rpivid_irq_irq, ++ rpivid_irq_thread, ++ 0, dev_name(dev->dev), dev); ++ if (ret) { ++ dev_err(dev->dev, "Failed to request IRQ - %d\n", ret); ++ ++ return ret; ++ } ++#endif ++ return ret; ++} ++ ++void rpivid_hw_remove(struct rpivid_dev *dev) ++{ ++ // IRQ auto freed on unload so no need to do it here ++ ictl_uninit(&dev->ic_active1); ++ ictl_uninit(&dev->ic_active2); ++} ++ +--- /dev/null ++++ b/drivers/staging/media/rpivid/rpivid_hw.h +@@ -0,0 +1,300 @@ ++/* SPDX-License-Identifier: GPL-2.0 */ ++/* ++ * Raspberry Pi HEVC driver ++ * ++ * Copyright (C) 2020 Raspberry Pi (Trading) Ltd ++ * ++ * Based on the Cedrus VPU driver, that is: ++ * ++ * Copyright (C) 2016 Florent Revest ++ * Copyright (C) 2018 Paul Kocialkowski ++ * Copyright (C) 2018 Bootlin ++ */ ++ ++#ifndef _RPIVID_HW_H_ ++#define _RPIVID_HW_H_ ++ ++struct rpivid_hw_irq_ent { ++ struct rpivid_hw_irq_ent *next; ++ rpivid_irq_callback cb; ++ void *v; ++}; ++ ++/* Phase 1 Register offsets */ ++ ++#define RPI_SPS0 0 ++#define RPI_SPS1 4 ++#define RPI_PPS 8 ++#define RPI_SLICE 12 ++#define RPI_TILESTART 16 ++#define RPI_TILEEND 20 ++#define RPI_SLICESTART 24 ++#define RPI_MODE 28 ++#define RPI_LEFT0 32 ++#define RPI_LEFT1 36 ++#define RPI_LEFT2 40 ++#define RPI_LEFT3 44 ++#define RPI_QP 48 ++#define RPI_CONTROL 52 ++#define RPI_STATUS 56 ++#define RPI_VERSION 60 ++#define RPI_BFBASE 64 ++#define RPI_BFNUM 68 ++#define RPI_BFCONTROL 72 ++#define RPI_BFSTATUS 76 ++#define RPI_PUWBASE 80 ++#define RPI_PUWSTRIDE 84 ++#define RPI_COEFFWBASE 88 ++#define RPI_COEFFWSTRIDE 92 ++#define RPI_SLICECMDS 96 ++#define RPI_BEGINTILEEND 100 ++#define RPI_TRANSFER 104 ++#define RPI_CFBASE 108 ++#define RPI_CFNUM 112 ++#define RPI_CFSTATUS 116 ++ ++/* Phase 2 Register offsets */ ++ ++#define RPI_PURBASE 0x8000 ++#define RPI_PURSTRIDE 0x8004 ++#define RPI_COEFFRBASE 0x8008 ++#define RPI_COEFFRSTRIDE 0x800C ++#define RPI_NUMROWS 0x8010 ++#define RPI_CONFIG2 0x8014 ++#define RPI_OUTYBASE 0x8018 ++#define RPI_OUTYSTRIDE 0x801C ++#define RPI_OUTCBASE 0x8020 ++#define RPI_OUTCSTRIDE 0x8024 ++#define RPI_STATUS2 0x8028 ++#define RPI_FRAMESIZE 0x802C ++#define RPI_MVBASE 0x8030 ++#define RPI_MVSTRIDE 0x8034 ++#define RPI_COLBASE 0x8038 ++#define RPI_COLSTRIDE 0x803C ++#define RPI_CURRPOC 0x8040 ++ ++/* ++ * Write a general register value ++ * Order is unimportant ++ */ ++static inline void apb_write(const struct rpivid_dev * const dev, ++ const unsigned int offset, const u32 val) ++{ ++ writel_relaxed(val, dev->base_h265 + offset); ++} ++ ++/* Write the final register value that actually starts the phase */ ++static inline void apb_write_final(const struct rpivid_dev * const dev, ++ const unsigned int offset, const u32 val) ++{ ++ writel(val, dev->base_h265 + offset); ++} ++ ++static inline u32 apb_read(const struct rpivid_dev * const dev, ++ const unsigned int offset) ++{ ++ return readl(dev->base_h265 + offset); ++} ++ ++static inline void irq_write(const struct rpivid_dev * const dev, ++ const unsigned int offset, const u32 val) ++{ ++ writel(val, dev->base_irq + offset); ++} ++ ++static inline u32 irq_read(const struct rpivid_dev * const dev, ++ const unsigned int offset) ++{ ++ return readl(dev->base_irq + offset); ++} ++ ++static inline void apb_write_vc_addr(const struct rpivid_dev * const dev, ++ const unsigned int offset, ++ const dma_addr_t a) ++{ ++ apb_write(dev, offset, (u32)(a >> 6)); ++} ++ ++static inline void apb_write_vc_addr_final(const struct rpivid_dev * const dev, ++ const unsigned int offset, ++ const dma_addr_t a) ++{ ++ apb_write_final(dev, offset, (u32)(a >> 6)); ++} ++ ++static inline void apb_write_vc_len(const struct rpivid_dev * const dev, ++ const unsigned int offset, ++ const unsigned int x) ++{ ++ apb_write(dev, offset, (x + 63) >> 6); ++} ++ ++/* *ARG_IC_ICTRL - Interrupt control for ARGON Core* ++ * Offset (byte space) = 40'h2b10000 ++ * Physical Address (byte space) = 40'h7eb10000 ++ * Verilog Macro Address = `ARG_IC_REG_START + `ARGON_INTCTRL_ICTRL ++ * Reset Value = 32'b100x100x_100xxxxx_xxxxxxx0_x100x100 ++ * Access = RW (32-bit only) ++ * Interrupt control logic for ARGON Core. ++ */ ++#define ARG_IC_ICTRL 0 ++ ++/* acc=LWC ACTIVE1_INT FIELD ACCESS: LWC ++ * ++ * Interrupt 1 ++ * This is set and held when an hevc_active1 interrupt edge is detected ++ * The polarity of the edge is set by the ACTIVE1_EDGE field ++ * Write a 1 to this bit to clear down the latched interrupt ++ * The latched interrupt is only enabled out onto the interrupt line if ++ * ACTIVE1_EN is set ++ * Reset value is *0* decimal. ++ */ ++#define ARG_IC_ICTRL_ACTIVE1_INT_SET BIT(0) ++ ++/* ACTIVE1_EDGE Sets the polarity of the interrupt edge detection logic ++ * This logic detects edges of the hevc_active1 line from the argon core ++ * 0 = negedge, 1 = posedge ++ * Reset value is *0* decimal. ++ */ ++#define ARG_IC_ICTRL_ACTIVE1_EDGE_SET BIT(1) ++ ++/* ACTIVE1_EN Enables ACTIVE1_INT out onto the argon interrupt line. ++ * If this isn't set, the interrupt logic will work but no interrupt will be ++ * set to the interrupt controller ++ * Reset value is *1* decimal. ++ * ++ * [JC] The above appears to be a lie - if unset then b0 is never set ++ */ ++#define ARG_IC_ICTRL_ACTIVE1_EN_SET BIT(2) ++ ++/* acc=RO ACTIVE1_STATUS FIELD ACCESS: RO ++ * ++ * The current status of the hevc_active1 signal ++ */ ++#define ARG_IC_ICTRL_ACTIVE1_STATUS_SET BIT(3) ++ ++/* acc=LWC ACTIVE2_INT FIELD ACCESS: LWC ++ * ++ * Interrupt 2 ++ * This is set and held when an hevc_active2 interrupt edge is detected ++ * The polarity of the edge is set by the ACTIVE2_EDGE field ++ * Write a 1 to this bit to clear down the latched interrupt ++ * The latched interrupt is only enabled out onto the interrupt line if ++ * ACTIVE2_EN is set ++ * Reset value is *0* decimal. ++ */ ++#define ARG_IC_ICTRL_ACTIVE2_INT_SET BIT(4) ++ ++/* ACTIVE2_EDGE Sets the polarity of the interrupt edge detection logic ++ * This logic detects edges of the hevc_active2 line from the argon core ++ * 0 = negedge, 1 = posedge ++ * Reset value is *0* decimal. ++ */ ++#define ARG_IC_ICTRL_ACTIVE2_EDGE_SET BIT(5) ++ ++/* ACTIVE2_EN Enables ACTIVE2_INT out onto the argon interrupt line. ++ * If this isn't set, the interrupt logic will work but no interrupt will be ++ * set to the interrupt controller ++ * Reset value is *1* decimal. ++ */ ++#define ARG_IC_ICTRL_ACTIVE2_EN_SET BIT(6) ++ ++/* acc=RO ACTIVE2_STATUS FIELD ACCESS: RO ++ * ++ * The current status of the hevc_active2 signal ++ */ ++#define ARG_IC_ICTRL_ACTIVE2_STATUS_SET BIT(7) ++ ++/* TEST_INT Forces the argon int high for test purposes. ++ * Reset value is *0* decimal. ++ */ ++#define ARG_IC_ICTRL_TEST_INT BIT(8) ++#define ARG_IC_ICTRL_SPARE BIT(9) ++ ++/* acc=RO VP9_INTERRUPT_STATUS FIELD ACCESS: RO ++ * ++ * The current status of the vp9_interrupt signal ++ */ ++#define ARG_IC_ICTRL_VP9_INTERRUPT_STATUS BIT(10) ++ ++/* AIO_INT_ENABLE 1 = Or the AIO int in with the Argon int so the VPU can see ++ * it ++ * 0 = the AIO int is masked. (It should still be connected to the GIC though). ++ */ ++#define ARG_IC_ICTRL_AIO_INT_ENABLE BIT(20) ++#define ARG_IC_ICTRL_H264_ACTIVE_INT BIT(21) ++#define ARG_IC_ICTRL_H264_ACTIVE_EDGE BIT(22) ++#define ARG_IC_ICTRL_H264_ACTIVE_EN BIT(23) ++#define ARG_IC_ICTRL_H264_ACTIVE_STATUS BIT(24) ++#define ARG_IC_ICTRL_H264_INTERRUPT_INT BIT(25) ++#define ARG_IC_ICTRL_H264_INTERRUPT_EDGE BIT(26) ++#define ARG_IC_ICTRL_H264_INTERRUPT_EN BIT(27) ++ ++/* acc=RO H264_INTERRUPT_STATUS FIELD ACCESS: RO ++ * ++ * The current status of the h264_interrupt signal ++ */ ++#define ARG_IC_ICTRL_H264_INTERRUPT_STATUS BIT(28) ++ ++/* acc=LWC VP9_INTERRUPT_INT FIELD ACCESS: LWC ++ * ++ * Interrupt 1 ++ * This is set and held when an vp9_interrupt interrupt edge is detected ++ * The polarity of the edge is set by the VP9_INTERRUPT_EDGE field ++ * Write a 1 to this bit to clear down the latched interrupt ++ * The latched interrupt is only enabled out onto the interrupt line if ++ * VP9_INTERRUPT_EN is set ++ * Reset value is *0* decimal. ++ */ ++#define ARG_IC_ICTRL_VP9_INTERRUPT_INT BIT(29) ++ ++/* VP9_INTERRUPT_EDGE Sets the polarity of the interrupt edge detection logic ++ * This logic detects edges of the vp9_interrupt line from the argon h264 core ++ * 0 = negedge, 1 = posedge ++ * Reset value is *0* decimal. ++ */ ++#define ARG_IC_ICTRL_VP9_INTERRUPT_EDGE BIT(30) ++ ++/* VP9_INTERRUPT_EN Enables VP9_INTERRUPT_INT out onto the argon interrupt line. ++ * If this isn't set, the interrupt logic will work but no interrupt will be ++ * set to the interrupt controller ++ * Reset value is *1* decimal. ++ */ ++#define ARG_IC_ICTRL_VP9_INTERRUPT_EN BIT(31) ++ ++/* Bits 19:12, 11 reserved - read ?, write 0 */ ++#define ARG_IC_ICTRL_SET_ZERO_MASK ((0xff << 12) | BIT(11)) ++ ++/* All IRQ bits */ ++#define ARG_IC_ICTRL_ALL_IRQ_MASK (\ ++ ARG_IC_ICTRL_VP9_INTERRUPT_INT |\ ++ ARG_IC_ICTRL_H264_INTERRUPT_INT |\ ++ ARG_IC_ICTRL_ACTIVE1_INT_SET |\ ++ ARG_IC_ICTRL_ACTIVE2_INT_SET) ++ ++/* Auto release once all CBs called */ ++void rpivid_hw_irq_active1_claim(struct rpivid_dev *dev, ++ struct rpivid_hw_irq_ent *ient, ++ rpivid_irq_callback ready_cb, void *ctx); ++/* May only be called in claim cb */ ++void rpivid_hw_irq_active1_irq(struct rpivid_dev *dev, ++ struct rpivid_hw_irq_ent *ient, ++ rpivid_irq_callback irq_cb, void *ctx); ++/* May only be called in irq cb */ ++void rpivid_hw_irq_active1_thread(struct rpivid_dev *dev, ++ struct rpivid_hw_irq_ent *ient, ++ rpivid_irq_callback thread_cb, void *ctx); ++ ++/* Auto release once all CBs called */ ++void rpivid_hw_irq_active2_claim(struct rpivid_dev *dev, ++ struct rpivid_hw_irq_ent *ient, ++ rpivid_irq_callback ready_cb, void *ctx); ++/* May only be called in claim cb */ ++void rpivid_hw_irq_active2_irq(struct rpivid_dev *dev, ++ struct rpivid_hw_irq_ent *ient, ++ rpivid_irq_callback irq_cb, void *ctx); ++ ++int rpivid_hw_probe(struct rpivid_dev *dev); ++void rpivid_hw_remove(struct rpivid_dev *dev); ++ ++#endif +--- /dev/null ++++ b/drivers/staging/media/rpivid/rpivid_video.c +@@ -0,0 +1,593 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * Raspberry Pi HEVC driver ++ * ++ * Copyright (C) 2020 Raspberry Pi (Trading) Ltd ++ * ++ * Based on the Cedrus VPU driver, that is: ++ * ++ * Copyright (C) 2016 Florent Revest ++ * Copyright (C) 2018 Paul Kocialkowski ++ * Copyright (C) 2018 Bootlin ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++ ++#include "rpivid.h" ++#include "rpivid_video.h" ++#include "rpivid_dec.h" ++ ++#define RPIVID_DECODE_SRC BIT(0) ++#define RPIVID_DECODE_DST BIT(1) ++ ++#define RPIVID_MIN_WIDTH 16U ++#define RPIVID_MIN_HEIGHT 16U ++#define RPIVID_MAX_WIDTH 4096U ++#define RPIVID_MAX_HEIGHT 4096U ++ ++static inline struct rpivid_ctx *rpivid_file2ctx(struct file *file) ++{ ++ return container_of(file->private_data, struct rpivid_ctx, fh); ++} ++ ++/* constrain x to y,y*2 */ ++static inline unsigned int constrain2x(unsigned int x, unsigned int y) ++{ ++ return (x < y) ? ++ y : ++ (x > y * 2) ? y : x; ++} ++ ++int rpivid_prepare_src_format(struct v4l2_pix_format *pix_fmt) ++{ ++ if (pix_fmt->pixelformat != V4L2_PIX_FMT_HEVC_SLICE) ++ return -EINVAL; ++ ++ /* Zero bytes per line for encoded source. */ ++ pix_fmt->bytesperline = 0; ++ /* Choose some minimum size since this can't be 0 */ ++ pix_fmt->sizeimage = max_t(u32, SZ_1K, pix_fmt->sizeimage); ++ pix_fmt->field = V4L2_FIELD_NONE; ++ return 0; ++} ++ ++int rpivid_prepare_dst_format(struct v4l2_pix_format *pix_fmt) ++{ ++ unsigned int width = pix_fmt->width; ++ unsigned int height = pix_fmt->height; ++ unsigned int sizeimage = pix_fmt->sizeimage; ++ unsigned int bytesperline = pix_fmt->bytesperline; ++ ++ switch (pix_fmt->pixelformat) { ++ /* For column formats set bytesperline to column height (stride2) */ ++ case V4L2_PIX_FMT_NV12_COL128: ++ /* Width rounds up to columns */ ++ width = ALIGN(min(width, RPIVID_MAX_WIDTH), 128); ++ ++ /* 16 aligned height - not sure we even need that */ ++ height = ALIGN(height, 16); ++ /* column height ++ * Accept suggested shape if at least min & < 2 * min ++ */ ++ bytesperline = constrain2x(bytesperline, height * 3 / 2); ++ ++ /* image size ++ * Again allow plausible variation in case added padding is ++ * required ++ */ ++ sizeimage = constrain2x(sizeimage, bytesperline * width); ++ break; ++ ++ case V4L2_PIX_FMT_NV12_10_COL128: ++ /* width in pixels (3 pels = 4 bytes) rounded to 128 byte ++ * columns ++ */ ++ width = ALIGN(((min(width, RPIVID_MAX_WIDTH) + 2) / 3), 32) * 3; ++ ++ /* 16-aligned height. */ ++ height = ALIGN(height, 16); ++ ++ /* column height ++ * Accept suggested shape if at least min & < 2 * min ++ */ ++ bytesperline = constrain2x(bytesperline, height * 3 / 2); ++ ++ /* image size ++ * Again allow plausible variation in case added padding is ++ * required ++ */ ++ sizeimage = constrain2x(sizeimage, ++ bytesperline * width * 4 / 3); ++ break; ++ ++ default: ++ return -EINVAL; ++ } ++ ++ pix_fmt->width = width; ++ pix_fmt->height = height; ++ ++ pix_fmt->field = V4L2_FIELD_NONE; ++ pix_fmt->bytesperline = bytesperline; ++ pix_fmt->sizeimage = sizeimage; ++ return 0; ++} ++ ++static int rpivid_querycap(struct file *file, void *priv, ++ struct v4l2_capability *cap) ++{ ++ strscpy(cap->driver, RPIVID_NAME, sizeof(cap->driver)); ++ strscpy(cap->card, RPIVID_NAME, sizeof(cap->card)); ++ snprintf(cap->bus_info, sizeof(cap->bus_info), ++ "platform:%s", RPIVID_NAME); ++ ++ return 0; ++} ++ ++static int rpivid_enum_fmt_vid_out(struct file *file, void *priv, ++ struct v4l2_fmtdesc *f) ++{ ++ // Input formats ++ ++ // H.265 Slice only currently ++ if (f->index == 0) { ++ f->pixelformat = V4L2_PIX_FMT_HEVC_SLICE; ++ return 0; ++ } ++ ++ return -EINVAL; ++} ++ ++static int rpivid_hevc_validate_sps(const struct v4l2_ctrl_hevc_sps * const sps) ++{ ++ const unsigned int ctb_log2_size_y = ++ sps->log2_min_luma_coding_block_size_minus3 + 3 + ++ sps->log2_diff_max_min_luma_coding_block_size; ++ const unsigned int min_tb_log2_size_y = ++ sps->log2_min_luma_transform_block_size_minus2 + 2; ++ const unsigned int max_tb_log2_size_y = min_tb_log2_size_y + ++ sps->log2_diff_max_min_luma_transform_block_size; ++ ++ /* Local limitations */ ++ if (sps->pic_width_in_luma_samples < 32 || ++ sps->pic_width_in_luma_samples > 4096) ++ return 0; ++ if (sps->pic_height_in_luma_samples < 32 || ++ sps->pic_height_in_luma_samples > 4096) ++ return 0; ++ if (!(sps->bit_depth_luma_minus8 == 0 || ++ sps->bit_depth_luma_minus8 == 2)) ++ return 0; ++ if (sps->bit_depth_luma_minus8 != sps->bit_depth_chroma_minus8) ++ return 0; ++ if (sps->chroma_format_idc != 1) ++ return 0; ++ ++ /* Limits from H.265 7.4.3.2.1 */ ++ if (sps->log2_max_pic_order_cnt_lsb_minus4 > 12) ++ return 0; ++ if (sps->sps_max_dec_pic_buffering_minus1 > 15) ++ return 0; ++ if (sps->sps_max_num_reorder_pics > ++ sps->sps_max_dec_pic_buffering_minus1) ++ return 0; ++ if (ctb_log2_size_y > 6) ++ return 0; ++ if (max_tb_log2_size_y > 5) ++ return 0; ++ if (max_tb_log2_size_y > ctb_log2_size_y) ++ return 0; ++ if (sps->max_transform_hierarchy_depth_inter > ++ (ctb_log2_size_y - min_tb_log2_size_y)) ++ return 0; ++ if (sps->max_transform_hierarchy_depth_intra > ++ (ctb_log2_size_y - min_tb_log2_size_y)) ++ return 0; ++ /* Check pcm stuff */ ++ if (sps->num_short_term_ref_pic_sets > 64) ++ return 0; ++ if (sps->num_long_term_ref_pics_sps > 32) ++ return 0; ++ return 1; ++} ++ ++static inline int is_sps_set(const struct v4l2_ctrl_hevc_sps * const sps) ++{ ++ return sps && sps->pic_width_in_luma_samples != 0; ++} ++ ++static u32 pixelformat_from_sps(const struct v4l2_ctrl_hevc_sps * const sps, ++ const int index) ++{ ++ u32 pf = 0; ++ ++ // Use width 0 as a signifier of unsetness ++ if (!is_sps_set(sps)) { ++ /* Treat this as an error? For now return both */ ++ if (index == 0) ++ pf = V4L2_PIX_FMT_NV12_COL128; ++ else if (index == 1) ++ pf = V4L2_PIX_FMT_NV12_10_COL128; ++ } else if (index == 0 && rpivid_hevc_validate_sps(sps)) { ++ if (sps->bit_depth_luma_minus8 == 0) ++ pf = V4L2_PIX_FMT_NV12_COL128; ++ else if (sps->bit_depth_luma_minus8 == 2) ++ pf = V4L2_PIX_FMT_NV12_10_COL128; ++ } ++ ++ return pf; ++} ++ ++static struct v4l2_pix_format ++rpivid_hevc_default_dst_fmt(struct rpivid_ctx * const ctx) ++{ ++ const struct v4l2_ctrl_hevc_sps * const sps = ++ rpivid_find_control_data(ctx, V4L2_CID_MPEG_VIDEO_HEVC_SPS); ++ struct v4l2_pix_format pix_fmt = { ++ .width = sps->pic_width_in_luma_samples, ++ .height = sps->pic_height_in_luma_samples, ++ .pixelformat = pixelformat_from_sps(sps, 0) ++ }; ++ ++ rpivid_prepare_dst_format(&pix_fmt); ++ return pix_fmt; ++} ++ ++static u32 rpivid_hevc_get_dst_pixelformat(struct rpivid_ctx * const ctx, ++ const int index) ++{ ++ const struct v4l2_ctrl_hevc_sps * const sps = ++ rpivid_find_control_data(ctx, V4L2_CID_MPEG_VIDEO_HEVC_SPS); ++ ++ return pixelformat_from_sps(sps, index); ++} ++ ++static int rpivid_enum_fmt_vid_cap(struct file *file, void *priv, ++ struct v4l2_fmtdesc *f) ++{ ++ struct rpivid_ctx * const ctx = rpivid_file2ctx(file); ++ ++ const u32 pf = rpivid_hevc_get_dst_pixelformat(ctx, f->index); ++ ++ if (pf == 0) ++ return -EINVAL; ++ ++ f->pixelformat = pf; ++ return 0; ++} ++ ++static int rpivid_g_fmt_vid_cap(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct rpivid_ctx *ctx = rpivid_file2ctx(file); ++ ++ if (!ctx->dst_fmt_set) ++ ctx->dst_fmt = rpivid_hevc_default_dst_fmt(ctx); ++ f->fmt.pix = ctx->dst_fmt; ++ return 0; ++} ++ ++static int rpivid_g_fmt_vid_out(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct rpivid_ctx *ctx = rpivid_file2ctx(file); ++ ++ f->fmt.pix = ctx->src_fmt; ++ return 0; ++} ++ ++static inline void copy_color(struct v4l2_pix_format *d, ++ const struct v4l2_pix_format *s) ++{ ++ d->colorspace = s->colorspace; ++ d->xfer_func = s->xfer_func; ++ d->ycbcr_enc = s->ycbcr_enc; ++ d->quantization = s->quantization; ++} ++ ++static int rpivid_try_fmt_vid_cap(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct rpivid_ctx *ctx = rpivid_file2ctx(file); ++ const struct v4l2_ctrl_hevc_sps * const sps = ++ rpivid_find_control_data(ctx, V4L2_CID_MPEG_VIDEO_HEVC_SPS); ++ u32 pixelformat; ++ int i; ++ ++ /* Reject format types we don't support */ ++ if (f->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) ++ return -EINVAL; ++ ++ for (i = 0; (pixelformat = pixelformat_from_sps(sps, i)) != 0; i++) { ++ if (f->fmt.pix.pixelformat == pixelformat) ++ break; ++ } ++ ++ // If we can't use requested fmt then set to default ++ if (pixelformat == 0) { ++ pixelformat = pixelformat_from_sps(sps, 0); ++ // If we don't have a default then give up ++ if (pixelformat == 0) ++ return -EINVAL; ++ } ++ ++ // We don't have any way of finding out colourspace so believe ++ // anything we are told - take anything set in src as a default ++ if (f->fmt.pix.colorspace == V4L2_COLORSPACE_DEFAULT) ++ copy_color(&f->fmt.pix, &ctx->src_fmt); ++ ++ f->fmt.pix.pixelformat = pixelformat; ++ return rpivid_prepare_dst_format(&f->fmt.pix); ++} ++ ++static int rpivid_try_fmt_vid_out(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ if (f->type != V4L2_BUF_TYPE_VIDEO_OUTPUT) ++ return -EINVAL; ++ ++ if (rpivid_prepare_src_format(&f->fmt.pix)) { ++ // Set default src format ++ f->fmt.pix.pixelformat = RPIVID_SRC_PIXELFORMAT_DEFAULT; ++ rpivid_prepare_src_format(&f->fmt.pix); ++ } ++ return 0; ++} ++ ++static int rpivid_s_fmt_vid_cap(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct rpivid_ctx *ctx = rpivid_file2ctx(file); ++ struct vb2_queue *vq; ++ int ret; ++ ++ vq = v4l2_m2m_get_vq(ctx->fh.m2m_ctx, f->type); ++ if (vb2_is_busy(vq)) ++ return -EBUSY; ++ ++ ret = rpivid_try_fmt_vid_cap(file, priv, f); ++ if (ret) ++ return ret; ++ ++ ctx->dst_fmt = f->fmt.pix; ++ ctx->dst_fmt_set = 1; ++ ++ return 0; ++} ++ ++static int rpivid_s_fmt_vid_out(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct rpivid_ctx *ctx = rpivid_file2ctx(file); ++ struct vb2_queue *vq; ++ int ret; ++ ++ vq = v4l2_m2m_get_vq(ctx->fh.m2m_ctx, f->type); ++ if (vb2_is_busy(vq)) ++ return -EBUSY; ++ ++ ret = rpivid_try_fmt_vid_out(file, priv, f); ++ if (ret) ++ return ret; ++ ++ ctx->src_fmt = f->fmt.pix; ++ ctx->dst_fmt_set = 0; // Setting src invalidates dst ++ ++ vq->subsystem_flags |= ++ VB2_V4L2_FL_SUPPORTS_M2M_HOLD_CAPTURE_BUF; ++ ++ /* Propagate colorspace information to capture. */ ++ copy_color(&ctx->dst_fmt, &f->fmt.pix); ++ return 0; ++} ++ ++const struct v4l2_ioctl_ops rpivid_ioctl_ops = { ++ .vidioc_querycap = rpivid_querycap, ++ ++ .vidioc_enum_fmt_vid_cap = rpivid_enum_fmt_vid_cap, ++ .vidioc_g_fmt_vid_cap = rpivid_g_fmt_vid_cap, ++ .vidioc_try_fmt_vid_cap = rpivid_try_fmt_vid_cap, ++ .vidioc_s_fmt_vid_cap = rpivid_s_fmt_vid_cap, ++ ++ .vidioc_enum_fmt_vid_out = rpivid_enum_fmt_vid_out, ++ .vidioc_g_fmt_vid_out = rpivid_g_fmt_vid_out, ++ .vidioc_try_fmt_vid_out = rpivid_try_fmt_vid_out, ++ .vidioc_s_fmt_vid_out = rpivid_s_fmt_vid_out, ++ ++ .vidioc_reqbufs = v4l2_m2m_ioctl_reqbufs, ++ .vidioc_querybuf = v4l2_m2m_ioctl_querybuf, ++ .vidioc_qbuf = v4l2_m2m_ioctl_qbuf, ++ .vidioc_dqbuf = v4l2_m2m_ioctl_dqbuf, ++ .vidioc_prepare_buf = v4l2_m2m_ioctl_prepare_buf, ++ .vidioc_create_bufs = v4l2_m2m_ioctl_create_bufs, ++ .vidioc_expbuf = v4l2_m2m_ioctl_expbuf, ++ ++ .vidioc_streamon = v4l2_m2m_ioctl_streamon, ++ .vidioc_streamoff = v4l2_m2m_ioctl_streamoff, ++ ++ .vidioc_try_decoder_cmd = v4l2_m2m_ioctl_stateless_try_decoder_cmd, ++ .vidioc_decoder_cmd = v4l2_m2m_ioctl_stateless_decoder_cmd, ++ ++ .vidioc_subscribe_event = v4l2_ctrl_subscribe_event, ++ .vidioc_unsubscribe_event = v4l2_event_unsubscribe, ++}; ++ ++static int rpivid_queue_setup(struct vb2_queue *vq, unsigned int *nbufs, ++ unsigned int *nplanes, unsigned int sizes[], ++ struct device *alloc_devs[]) ++{ ++ struct rpivid_ctx *ctx = vb2_get_drv_priv(vq); ++ struct v4l2_pix_format *pix_fmt; ++ ++ if (V4L2_TYPE_IS_OUTPUT(vq->type)) ++ pix_fmt = &ctx->src_fmt; ++ else ++ pix_fmt = &ctx->dst_fmt; ++ ++ if (*nplanes) { ++ if (sizes[0] < pix_fmt->sizeimage) ++ return -EINVAL; ++ } else { ++ sizes[0] = pix_fmt->sizeimage; ++ *nplanes = 1; ++ } ++ ++ return 0; ++} ++ ++static void rpivid_queue_cleanup(struct vb2_queue *vq, u32 state) ++{ ++ struct rpivid_ctx *ctx = vb2_get_drv_priv(vq); ++ struct vb2_v4l2_buffer *vbuf; ++ ++ for (;;) { ++ if (V4L2_TYPE_IS_OUTPUT(vq->type)) ++ vbuf = v4l2_m2m_src_buf_remove(ctx->fh.m2m_ctx); ++ else ++ vbuf = v4l2_m2m_dst_buf_remove(ctx->fh.m2m_ctx); ++ ++ if (!vbuf) ++ return; ++ ++ v4l2_ctrl_request_complete(vbuf->vb2_buf.req_obj.req, ++ &ctx->hdl); ++ v4l2_m2m_buf_done(vbuf, state); ++ } ++} ++ ++static int rpivid_buf_out_validate(struct vb2_buffer *vb) ++{ ++ struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb); ++ ++ vbuf->field = V4L2_FIELD_NONE; ++ return 0; ++} ++ ++static int rpivid_buf_prepare(struct vb2_buffer *vb) ++{ ++ struct vb2_queue *vq = vb->vb2_queue; ++ struct rpivid_ctx *ctx = vb2_get_drv_priv(vq); ++ struct v4l2_pix_format *pix_fmt; ++ ++ if (V4L2_TYPE_IS_OUTPUT(vq->type)) ++ pix_fmt = &ctx->src_fmt; ++ else ++ pix_fmt = &ctx->dst_fmt; ++ ++ if (vb2_plane_size(vb, 0) < pix_fmt->sizeimage) ++ return -EINVAL; ++ ++ vb2_set_plane_payload(vb, 0, pix_fmt->sizeimage); ++ ++ return 0; ++} ++ ++static int rpivid_start_streaming(struct vb2_queue *vq, unsigned int count) ++{ ++ struct rpivid_ctx *ctx = vb2_get_drv_priv(vq); ++ struct rpivid_dev *dev = ctx->dev; ++ int ret = 0; ++ ++ if (ctx->src_fmt.pixelformat != V4L2_PIX_FMT_HEVC_SLICE) ++ return -EINVAL; ++ ++ if (V4L2_TYPE_IS_OUTPUT(vq->type) && dev->dec_ops->start) ++ ret = dev->dec_ops->start(ctx); ++ ++ ret = clk_set_rate(dev->clock, 500 * 1000 * 1000); ++ if (ret) { ++ dev_err(dev->dev, "Failed to set clock rate\n"); ++ goto out; ++ } ++ ++ ret = clk_prepare_enable(dev->clock); ++ if (ret) ++ dev_err(dev->dev, "Failed to enable clock\n"); ++ ++out: ++ if (ret) ++ rpivid_queue_cleanup(vq, VB2_BUF_STATE_QUEUED); ++ ++ return ret; ++} ++ ++static void rpivid_stop_streaming(struct vb2_queue *vq) ++{ ++ struct rpivid_ctx *ctx = vb2_get_drv_priv(vq); ++ struct rpivid_dev *dev = ctx->dev; ++ ++ if (V4L2_TYPE_IS_OUTPUT(vq->type) && dev->dec_ops->stop) ++ dev->dec_ops->stop(ctx); ++ ++ rpivid_queue_cleanup(vq, VB2_BUF_STATE_ERROR); ++ ++ clk_disable_unprepare(dev->clock); ++} ++ ++static void rpivid_buf_queue(struct vb2_buffer *vb) ++{ ++ struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb); ++ struct rpivid_ctx *ctx = vb2_get_drv_priv(vb->vb2_queue); ++ ++ v4l2_m2m_buf_queue(ctx->fh.m2m_ctx, vbuf); ++} ++ ++static void rpivid_buf_request_complete(struct vb2_buffer *vb) ++{ ++ struct rpivid_ctx *ctx = vb2_get_drv_priv(vb->vb2_queue); ++ ++ v4l2_ctrl_request_complete(vb->req_obj.req, &ctx->hdl); ++} ++ ++static struct vb2_ops rpivid_qops = { ++ .queue_setup = rpivid_queue_setup, ++ .buf_prepare = rpivid_buf_prepare, ++ .buf_queue = rpivid_buf_queue, ++ .buf_out_validate = rpivid_buf_out_validate, ++ .buf_request_complete = rpivid_buf_request_complete, ++ .start_streaming = rpivid_start_streaming, ++ .stop_streaming = rpivid_stop_streaming, ++ .wait_prepare = vb2_ops_wait_prepare, ++ .wait_finish = vb2_ops_wait_finish, ++}; ++ ++int rpivid_queue_init(void *priv, struct vb2_queue *src_vq, ++ struct vb2_queue *dst_vq) ++{ ++ struct rpivid_ctx *ctx = priv; ++ int ret; ++ ++ src_vq->type = V4L2_BUF_TYPE_VIDEO_OUTPUT; ++ src_vq->io_modes = VB2_MMAP | VB2_DMABUF; ++ src_vq->drv_priv = ctx; ++ src_vq->buf_struct_size = sizeof(struct rpivid_buffer); ++ src_vq->min_buffers_needed = 1; ++ src_vq->ops = &rpivid_qops; ++ src_vq->mem_ops = &vb2_dma_contig_memops; ++ src_vq->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_COPY; ++ src_vq->lock = &ctx->dev->dev_mutex; ++ src_vq->dev = ctx->dev->dev; ++ src_vq->supports_requests = true; ++ src_vq->requires_requests = true; ++ ++ ret = vb2_queue_init(src_vq); ++ if (ret) ++ return ret; ++ ++ dst_vq->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; ++ dst_vq->io_modes = VB2_MMAP | VB2_DMABUF; ++ dst_vq->drv_priv = ctx; ++ dst_vq->buf_struct_size = sizeof(struct rpivid_buffer); ++ dst_vq->min_buffers_needed = 1; ++ dst_vq->ops = &rpivid_qops; ++ dst_vq->mem_ops = &vb2_dma_contig_memops; ++ dst_vq->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_COPY; ++ dst_vq->lock = &ctx->dev->dev_mutex; ++ dst_vq->dev = ctx->dev->dev; ++ ++ return vb2_queue_init(dst_vq); ++} +--- /dev/null ++++ b/drivers/staging/media/rpivid/rpivid_video.h +@@ -0,0 +1,30 @@ ++/* SPDX-License-Identifier: GPL-2.0 */ ++/* ++ * Raspberry Pi HEVC driver ++ * ++ * Copyright (C) 2020 Raspberry Pi (Trading) Ltd ++ * ++ * Based on the Cedrus VPU driver, that is: ++ * ++ * Copyright (C) 2016 Florent Revest ++ * Copyright (C) 2018 Paul Kocialkowski ++ * Copyright (C) 2018 Bootlin ++ */ ++ ++#ifndef _RPIVID_VIDEO_H_ ++#define _RPIVID_VIDEO_H_ ++ ++struct rpivid_format { ++ u32 pixelformat; ++ u32 directions; ++ unsigned int capabilities; ++}; ++ ++extern const struct v4l2_ioctl_ops rpivid_ioctl_ops; ++ ++int rpivid_queue_init(void *priv, struct vb2_queue *src_vq, ++ struct vb2_queue *dst_vq); ++int rpivid_prepare_src_format(struct v4l2_pix_format *pix_fmt); ++int rpivid_prepare_dst_format(struct v4l2_pix_format *pix_fmt); ++ ++#endif diff --git a/target/linux/bcm27xx/patches-5.10/950-0201-mmc-sdhci-Silence-MMC-warnings.patch b/target/linux/bcm27xx/patches-5.10/950-0201-mmc-sdhci-Silence-MMC-warnings.patch new file mode 100644 index 0000000000..071aa0287c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0201-mmc-sdhci-Silence-MMC-warnings.patch @@ -0,0 +1,42 @@ +From 966a8df34ba0d98908dd381f27f6cfd615b3cb74 Mon Sep 17 00:00:00 2001 +From: Maxime Ripard +Date: Fri, 6 Dec 2019 13:05:27 +0100 +Subject: [PATCH] mmc: sdhci: Silence MMC warnings + +When the MMC isn't plugged in, the driver will spam the console which is +pretty annoying when using NFS. + +Signed-off-by: Maxime Ripard +--- + drivers/mmc/host/sdhci.c | 6 +++--- + 1 file changed, 3 insertions(+), 3 deletions(-) + +--- a/drivers/mmc/host/sdhci.c ++++ b/drivers/mmc/host/sdhci.c +@@ -41,7 +41,7 @@ + pr_debug("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x) + + #define SDHCI_DUMP(f, x...) \ +- pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x) ++ pr_debug("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x) + + #define MAX_TUNING_LOOP 40 + +@@ -3126,7 +3126,7 @@ static void sdhci_timeout_timer(struct t + spin_lock_irqsave(&host->lock, flags); + + if (host->cmd && !sdhci_data_line_cmd(host->cmd)) { +- pr_err("%s: Timeout waiting for hardware cmd interrupt.\n", ++ pr_debug("%s: Timeout waiting for hardware cmd interrupt.\n", + mmc_hostname(host->mmc)); + sdhci_dumpregs(host); + +@@ -3148,7 +3148,7 @@ static void sdhci_timeout_data_timer(str + + if (host->data || host->data_cmd || + (host->cmd && sdhci_data_line_cmd(host->cmd))) { +- pr_err("%s: Timeout waiting for hardware interrupt.\n", ++ pr_debug("%s: Timeout waiting for hardware interrupt.\n", + mmc_hostname(host->mmc)); + sdhci_dumpregs(host); + diff --git a/target/linux/bcm27xx/patches-5.10/950-0202-dt-bindings-clock-Add-a-binding-for-the-RPi-Firmware.patch b/target/linux/bcm27xx/patches-5.10/950-0202-dt-bindings-clock-Add-a-binding-for-the-RPi-Firmware.patch new file mode 100644 index 0000000000..3cca6de751 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0202-dt-bindings-clock-Add-a-binding-for-the-RPi-Firmware.patch @@ -0,0 +1,63 @@ +From 5567ea58dd5814de7dd1c9756ab985fd0f753bce Mon Sep 17 00:00:00 2001 +From: Maxime Ripard +Date: Thu, 13 Feb 2020 17:51:09 +0100 +Subject: [PATCH] dt-bindings: clock: Add a binding for the RPi + Firmware clocks + +The firmare running on the RPi VideoCore can be used to discover and +change the various clocks running in the BCM2711. Since devices will +need to use them through the DT, let's add a pretty simple binding. + +Cc: Michael Turquette +Cc: Stephen Boyd +Cc: Rob Herring +Cc: linux-clk@vger.kernel.org +Cc: devicetree@vger.kernel.org +Signed-off-by: Maxime Ripard +--- + .../clock/raspberrypi,firmware-clocks.yaml | 39 +++++++++++++++++++ + 1 file changed, 39 insertions(+) + create mode 100644 Documentation/devicetree/bindings/clock/raspberrypi,firmware-clocks.yaml + +--- /dev/null ++++ b/Documentation/devicetree/bindings/clock/raspberrypi,firmware-clocks.yaml +@@ -0,0 +1,39 @@ ++# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) ++%YAML 1.2 ++--- ++$id: http://devicetree.org/schemas/clock/raspberrypi,firmware-clocks.yaml# ++$schema: http://devicetree.org/meta-schemas/core.yaml# ++ ++title: RaspberryPi Firmware Clocks Device Tree Bindings ++ ++maintainers: ++ - Maxime Ripard ++ ++properties: ++ "#clock-cells": ++ const: 1 ++ ++ compatible: ++ const: raspberrypi,firmware-clocks ++ ++ raspberrypi,firmware: ++ $ref: /schemas/types.yaml#/definitions/phandle ++ description: > ++ Phandle to the mailbox node to communicate with the firmware. ++ ++required: ++ - "#clock-cells" ++ - compatible ++ - raspberrypi,firmware ++ ++additionalProperties: false ++ ++examples: ++ - | ++ firmware_clocks: firmware-clocks { ++ compatible = "raspberrypi,firmware-clocks"; ++ raspberrypi,firmware = <&firmware>; ++ #clock-cells = <1>; ++ }; ++ ++... diff --git a/target/linux/bcm27xx/patches-5.10/950-0203-dt-bindings-display-vc4-hdmi-Add-BCM2711-HDMI-contro.patch b/target/linux/bcm27xx/patches-5.10/950-0203-dt-bindings-display-vc4-hdmi-Add-BCM2711-HDMI-contro.patch new file mode 100644 index 0000000000..13d9012610 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0203-dt-bindings-display-vc4-hdmi-Add-BCM2711-HDMI-contro.patch @@ -0,0 +1,174 @@ +From 2cbd6432676b68e210f9ff4a1c1dd5d5463a6d6b Mon Sep 17 00:00:00 2001 +From: Maxime Ripard +Date: Thu, 13 Feb 2020 16:45:24 +0100 +Subject: [PATCH] dt-bindings: display: vc4: hdmi: Add BCM2711 HDMI + controllers bindings + +The HDMI controllers found in the BCM2711 SoC need some adjustments to the +bindings, especially since the registers have been shuffled around in more +register ranges. + +Cc: Rob Herring +Cc: devicetree@vger.kernel.org +Signed-off-by: Maxime Ripard +--- + .../bindings/display/brcm,bcm2835-hdmi.yaml | 118 ++++++++++++++++-- + 1 file changed, 109 insertions(+), 9 deletions(-) + +--- a/Documentation/devicetree/bindings/display/brcm,bcm2835-hdmi.yaml ++++ b/Documentation/devicetree/bindings/display/brcm,bcm2835-hdmi.yaml +@@ -11,24 +11,58 @@ maintainers: + + properties: + compatible: +- const: brcm,bcm2835-hdmi ++ enum: ++ - brcm,bcm2835-hdmi ++ - brcm,bcm2711-hdmi0 ++ - brcm,bcm2711-hdmi1 + + reg: ++ oneOf: ++ - items: ++ - description: HDMI register range ++ - description: HD register range ++ ++ - items: ++ - description: HDMI controller register range ++ - description: DVP register range ++ - description: HDMI PHY register range ++ - description: Rate Manager register range ++ - description: Packet RAM register range ++ - description: Metadata RAM register range ++ - description: CSC register range ++ - description: CEC register range ++ - description: HD register range ++ ++ reg-names: + items: +- - description: HDMI register range +- - description: HD register range ++ - const: hdmi ++ - const: dvp ++ - const: phy ++ - const: rm ++ - const: packet ++ - const: metadata ++ - const: csc ++ - const: cec ++ - const: hd + + interrupts: + minItems: 2 + + clocks: +- items: +- - description: The pixel clock +- - description: The HDMI state machine clock ++ oneOf: ++ - items: ++ - description: The pixel clock ++ - description: The HDMI state machine clock ++ ++ - items: ++ - description: The HDMI state machine clock + + clock-names: +- items: +- - const: pixel ++ oneOf: ++ - items: ++ - const: pixel ++ - const: hdmi ++ + - const: hdmi + + ddc: +@@ -50,15 +84,54 @@ properties: + dma-names: + const: audio-rx + ++ resets: ++ maxItems: 1 ++ + required: + - compatible + - reg +- - interrupts + - clocks + - ddc + + additionalProperties: false + ++if: ++ properties: ++ compatible: ++ contains: ++ enum: ++ - brcm,bcm2711-hdmi0 ++ - brcm,bcm2711-hdmi1 ++ ++then: ++ properties: ++ reg: ++ minItems: 9 ++ ++ clocks: ++ maxItems: 1 ++ ++ clock-names: ++ maxItems: 1 ++ ++ required: ++ - reg-names ++ - resets ++ ++else: ++ properties: ++ reg: ++ maxItems: 2 ++ ++ clocks: ++ minItems: 2 ++ ++ clock-names: ++ minItems: 2 ++ ++ required: ++ - interrupts ++ + examples: + - | + #include +@@ -76,4 +149,31 @@ examples: + clock-names = "pixel", "hdmi"; + }; + ++ - | ++ hdmi0: hdmi@7ef00700 { ++ compatible = "brcm,bcm2711-hdmi0"; ++ reg = <0x7ef00700 0x300>, ++ <0x7ef00300 0x200>, ++ <0x7ef00f00 0x80>, ++ <0x7ef00f80 0x80>, ++ <0x7ef01b00 0x200>, ++ <0x7ef01f00 0x400>, ++ <0x7ef00200 0x80>, ++ <0x7ef04300 0x100>, ++ <0x7ef20000 0x100>; ++ reg-names = "hdmi", ++ "dvp", ++ "phy", ++ "rm", ++ "packet", ++ "metadata", ++ "csc", ++ "cec", ++ "hd"; ++ clocks = <&firmware_clocks 13>; ++ clock-names = "hdmi"; ++ resets = <&dvp 0>; ++ ddc = <&ddc0>; ++ }; ++ + ... diff --git a/target/linux/bcm27xx/patches-5.10/950-0204-drm-Checking-of-the-pitch-is-only-valid-for-linear-f.patch b/target/linux/bcm27xx/patches-5.10/950-0204-drm-Checking-of-the-pitch-is-only-valid-for-linear-f.patch new file mode 100644 index 0000000000..44e0648700 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0204-drm-Checking-of-the-pitch-is-only-valid-for-linear-f.patch @@ -0,0 +1,39 @@ +From c24a6aef5b7ef24fb5c6f83ada015b06bcc3c665 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Mon, 27 Jan 2020 10:22:44 +0000 +Subject: [PATCH] drm: Checking of the pitch is only valid for linear + formats + +framebuffer_check was computing a minimum pitch value and ensuring +that the provided value was greater than this. +That check is only valid if the format is linear. + +Signed-off-by: Dave Stevenson +--- + drivers/gpu/drm/drm_framebuffer.c | 16 ++++++++++------ + 1 file changed, 10 insertions(+), 6 deletions(-) + +--- a/drivers/gpu/drm/drm_framebuffer.c ++++ b/drivers/gpu/drm/drm_framebuffer.c +@@ -217,12 +217,16 @@ static int framebuffer_check(struct drm_ + if (min_pitch > UINT_MAX) + return -ERANGE; + +- if ((uint64_t) height * r->pitches[i] + r->offsets[i] > UINT_MAX) +- return -ERANGE; ++ if (r->modifier[i] == DRM_FORMAT_MOD_LINEAR) { ++ if ((uint64_t)height * r->pitches[i] + r->offsets[i] > ++ UINT_MAX) ++ return -ERANGE; + +- if (block_size && r->pitches[i] < min_pitch) { +- DRM_DEBUG_KMS("bad pitch %u for plane %d\n", r->pitches[i], i); +- return -EINVAL; ++ if (block_size && r->pitches[i] < min_pitch) { ++ DRM_DEBUG_KMS("bad pitch %u for plane %d\n", ++ r->pitches[i], i); ++ return -EINVAL; ++ } + } + + if (r->modifier[i] && !(r->flags & DRM_MODE_FB_MODIFIERS)) { diff --git a/target/linux/bcm27xx/patches-5.10/950-0205-overlays-Fix-dtc-warnings-in-i2c-gpio.patch b/target/linux/bcm27xx/patches-5.10/950-0205-overlays-Fix-dtc-warnings-in-i2c-gpio.patch new file mode 100644 index 0000000000..43db2828bb --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0205-overlays-Fix-dtc-warnings-in-i2c-gpio.patch @@ -0,0 +1,24 @@ +From 987af76904b945d39b90e6a5294f8f2f691fb8fb Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 8 Apr 2020 11:59:39 +0100 +Subject: [PATCH] overlays: Fix dtc warnings in i2c-gpio + +Better late than never. + +Signed-off-by: Phil Elwell +--- + arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts ++++ b/arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts +@@ -11,6 +11,9 @@ + target-path = "/"; + + __overlay__ { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ + i2c_gpio: i2c@0 { + reg = <0xffffffff>; + compatible = "i2c-gpio"; diff --git a/target/linux/bcm27xx/patches-5.10/950-0206-driver-char-rpivid-Remove-legacy-name-support.patch b/target/linux/bcm27xx/patches-5.10/950-0206-driver-char-rpivid-Remove-legacy-name-support.patch new file mode 100644 index 0000000000..1e21fb17b0 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0206-driver-char-rpivid-Remove-legacy-name-support.patch @@ -0,0 +1,53 @@ +From 8967fee444367746114e366fd48331e56f0d36d6 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 20 Apr 2020 22:18:52 +0100 +Subject: [PATCH] driver: char: rpivid: Remove legacy name support + +Signed-off-by: Phil Elwell +--- + drivers/char/broadcom/rpivid-mem.c | 22 ---------------------- + 1 file changed, 22 deletions(-) + +--- a/drivers/char/broadcom/rpivid-mem.c ++++ b/drivers/char/broadcom/rpivid-mem.c +@@ -193,32 +193,11 @@ static int rpivid_mem_probe(struct platf + goto failed_device_create; + } + +- /* Legacy alias */ +- { +- char *oldname = kstrdup(priv->name, GFP_KERNEL); +- +- oldname[1] = 'a'; +- oldname[2] = 'r'; +- oldname[3] = 'g'; +- oldname[4] = 'o'; +- oldname[5] = 'n'; +- dev = device_create(priv->class, NULL, priv->devid + 1, NULL, +- oldname + 1); +- kfree(oldname); +- +- if (IS_ERR(dev)) { +- err = PTR_ERR(dev); +- goto failed_legacy_device_create; +- } +- } +- + dev_info(priv->dev, "%s initialised: Registers at 0x%08lx length 0x%08lx", + priv->name, priv->regs_phys, priv->mem_window_len); + + return 0; + +-failed_legacy_device_create: +- device_destroy(priv->class, priv->devid); + failed_device_create: + class_destroy(priv->class); + failed_class_create: +@@ -238,7 +217,6 @@ static int rpivid_mem_remove(struct plat + struct device *dev = &pdev->dev; + struct rpivid_mem_priv *priv = platform_get_drvdata(pdev); + +- device_destroy(priv->class, priv->devid + 1); + device_destroy(priv->class, priv->devid); + class_destroy(priv->class); + cdev_del(&priv->rpivid_mem_cdev); diff --git a/target/linux/bcm27xx/patches-5.10/950-0207-spi-Force-CS_HIGH-if-GPIO-descriptors-are-used.patch b/target/linux/bcm27xx/patches-5.10/950-0207-spi-Force-CS_HIGH-if-GPIO-descriptors-are-used.patch new file mode 100644 index 0000000000..64572594a5 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0207-spi-Force-CS_HIGH-if-GPIO-descriptors-are-used.patch @@ -0,0 +1,57 @@ +From 4b6c8cda93174f36754f549498c133ccaeaa2218 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 17 Apr 2020 10:46:19 +0100 +Subject: [PATCH] spi: Force CS_HIGH if GPIO descriptors are used + +Commit f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs") +amended of_spi_parse_dt() to always set SPI_CS_HIGH for SPI slaves whose +Chip Select is defined by a "cs-gpios" devicetree property. + +This change breaks drivers whose probe functions set the mode field of +the spi_device because in doing so they clear the SPI_CS_HIGH flag. + +Fix by setting SPI_CS_HIGH in spi_setup (under the same conditions as +in of_spi_parse_dt()). + +See also: 83b2a8fe43bd ("spi: spidev: Fix CS polarity if GPIO descriptors are used") + +Fixes: f3186dd87669 ("spi: Optionally use GPIO descriptors for CS GPIOs") +Signed-off-by: Phil Elwell + +SQUASH: spi: Demote SPI_CS_HIGH warning to KERN_DEBUG + +This warning is unavoidable from a client's perspective and +doesn't indicate anything wrong (just surprising). + +SQUASH with "spi: use_gpio_descriptor fixup moved to spi_setup" + +Signed-off-by: Phil Elwell +--- + drivers/spi/spi.c | 9 +++++++++ + 1 file changed, 9 insertions(+) + +--- a/drivers/spi/spi.c ++++ b/drivers/spi/spi.c +@@ -3338,6 +3338,7 @@ static int __spi_validate_bits_per_word( + */ + int spi_setup(struct spi_device *spi) + { ++ struct spi_controller *ctlr = spi->controller; + unsigned bad_bits, ugly_bits; + int status; + +@@ -3355,6 +3356,14 @@ int spi_setup(struct spi_device *spi) + (SPI_TX_DUAL | SPI_TX_QUAD | SPI_TX_OCTAL | + SPI_RX_DUAL | SPI_RX_QUAD | SPI_RX_OCTAL))) + return -EINVAL; ++ ++ if (ctlr->use_gpio_descriptors && ctlr->cs_gpiods && ++ ctlr->cs_gpiods[spi->chip_select] && !(spi->mode & SPI_CS_HIGH)) { ++ dev_dbg(&spi->dev, ++ "setup: forcing CS_HIGH (use_gpio_descriptors)\n"); ++ spi->mode |= SPI_CS_HIGH; ++ } ++ + /* help drivers fail *cleanly* when they need options + * that aren't supported with their current controller + * SPI_CS_WORD has a fallback software implementation, diff --git a/target/linux/bcm27xx/patches-5.10/950-0208-driver-char-rpivid-Don-t-map-more-than-wanted.patch b/target/linux/bcm27xx/patches-5.10/950-0208-driver-char-rpivid-Don-t-map-more-than-wanted.patch new file mode 100644 index 0000000000..849c44197f --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0208-driver-char-rpivid-Don-t-map-more-than-wanted.patch @@ -0,0 +1,51 @@ +From 7b7873548f21f42e6d3032d038d3e8b2c2b22939 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 21 Apr 2020 11:30:23 +0100 +Subject: [PATCH] driver: char: rpivid: Don't map more than wanted + +Limit mappings to the permitted range, but don't map more than asked +for otherwise we walk off the end of the allocated VMA. + +Signed-off-by: Phil Elwell +--- + drivers/char/broadcom/rpivid-mem.c | 12 ++++++------ + 1 file changed, 6 insertions(+), 6 deletions(-) + +--- a/drivers/char/broadcom/rpivid-mem.c ++++ b/drivers/char/broadcom/rpivid-mem.c +@@ -100,6 +100,7 @@ static int rpivid_mem_mmap(struct file * + { + struct rpivid_mem_priv *priv; + unsigned long pages; ++ unsigned long len; + + priv = file->private_data; + pages = priv->regs_phys >> PAGE_SHIFT; +@@ -107,14 +108,13 @@ static int rpivid_mem_mmap(struct file * + * The address decode is far larger than the actual number of registers. + * Just map the whole lot in. + */ +- vma->vm_page_prot = phys_mem_access_prot(file, pages, +- priv->mem_window_len, ++ len = min(vma->vm_end - vma->vm_start, priv->mem_window_len); ++ vma->vm_page_prot = phys_mem_access_prot(file, pages, len, + vma->vm_page_prot); + vma->vm_ops = &rpivid_mem_vm_ops; + if (remap_pfn_range(vma, vma->vm_start, +- pages, +- priv->mem_window_len, +- vma->vm_page_prot)) { ++ pages, len, ++ vma->vm_page_prot)) { + return -EAGAIN; + } + return 0; +@@ -156,7 +156,7 @@ static int rpivid_mem_probe(struct platf + ioresource = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (ioresource) { + priv->regs_phys = ioresource->start; +- priv->mem_window_len = ioresource->end - ioresource->start; ++ priv->mem_window_len = (ioresource->end + 1) - ioresource->start; + } else { + dev_err(priv->dev, "failed to get IO resource"); + err = -ENOENT; diff --git a/target/linux/bcm27xx/patches-5.10/950-0209-media-bcm2835-unicam-Driver-for-CCP2-CSI2-camera-int.patch b/target/linux/bcm27xx/patches-5.10/950-0209-media-bcm2835-unicam-Driver-for-CCP2-CSI2-camera-int.patch new file mode 100644 index 0000000000..8e573e6e84 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0209-media-bcm2835-unicam-Driver-for-CCP2-CSI2-camera-int.patch @@ -0,0 +1,2709 @@ +From cbbd6cbf9376ae582e1141f41a0011341cac0fc5 Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Wed, 1 Apr 2020 08:39:49 +0100 +Subject: [PATCH] media: bcm2835-unicam: Driver for CCP2/CSI2 camera + interface + +Add driver for the Unicam camera receiver block on +BCM283x processors. + +This commit is made up of a series of changes cherry-picked from the +rpi-4.19.y branch. + +Signed-off-by: Dave Stevenson +Signed-off-by: Naushir Patuck +--- + MAINTAINERS | 2 +- + drivers/media/platform/Kconfig | 1 + + drivers/media/platform/Makefile | 2 + + drivers/media/platform/bcm2835/Kconfig | 14 + + drivers/media/platform/bcm2835/Makefile | 3 + + .../media/platform/bcm2835/bcm2835-unicam.c | 2369 +++++++++++++++++ + .../media/platform/bcm2835/vc4-regs-unicam.h | 253 ++ + 7 files changed, 2643 insertions(+), 1 deletion(-) + create mode 100644 drivers/media/platform/bcm2835/Kconfig + create mode 100644 drivers/media/platform/bcm2835/Makefile + create mode 100644 drivers/media/platform/bcm2835/bcm2835-unicam.c + create mode 100644 drivers/media/platform/bcm2835/vc4-regs-unicam.h + +--- a/MAINTAINERS ++++ b/MAINTAINERS +@@ -3425,7 +3425,7 @@ F: Documentation/devicetree/bindings/med + F: drivers/staging/media/rpivid + + BROADCOM BCM2835 CAMERA DRIVER +-M: Dave Stevenson ++M: Raspberry Pi Kernel Maintenance + L: linux-media@vger.kernel.org + S: Maintained + F: drivers/media/platform/bcm2835/ +--- a/drivers/media/platform/Kconfig ++++ b/drivers/media/platform/Kconfig +@@ -152,6 +152,7 @@ source "drivers/media/platform/am437x/Kc + source "drivers/media/platform/xilinx/Kconfig" + source "drivers/media/platform/rcar-vin/Kconfig" + source "drivers/media/platform/atmel/Kconfig" ++source "drivers/media/platform/bcm2835/Kconfig" + source "drivers/media/platform/sunxi/Kconfig" + + config VIDEO_TI_CAL +--- a/drivers/media/platform/Makefile ++++ b/drivers/media/platform/Makefile +@@ -79,4 +79,6 @@ obj-$(CONFIG_VIDEO_QCOM_CAMSS) += qcom/ + + obj-$(CONFIG_VIDEO_QCOM_VENUS) += qcom/venus/ + ++obj-y += bcm2835/ ++ + obj-y += sunxi/ +--- /dev/null ++++ b/drivers/media/platform/bcm2835/Kconfig +@@ -0,0 +1,14 @@ ++# Broadcom VideoCore4 V4L2 camera support ++ ++config VIDEO_BCM2835_UNICAM ++ tristate "Broadcom BCM2835 Unicam video capture driver" ++ depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && MEDIA_CONTROLLER ++ depends on ARCH_BCM2835 || COMPILE_TEST ++ select VIDEOBUF2_DMA_CONTIG ++ select V4L2_FWNODE ++ help ++ Say Y here to enable V4L2 subdevice for CSI2 receiver. ++ This is a V4L2 subdevice that interfaces directly to the VC4 peripheral. ++ ++ To compile this driver as a module, choose M here. The module ++ will be called bcm2835-unicam. +--- /dev/null ++++ b/drivers/media/platform/bcm2835/Makefile +@@ -0,0 +1,3 @@ ++# Makefile for BCM2835 Unicam driver ++ ++obj-$(CONFIG_VIDEO_BCM2835_UNICAM) += bcm2835-unicam.o +--- /dev/null ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -0,0 +1,2369 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++/* ++ * BCM2835 Unicam Capture Driver ++ * ++ * Copyright (C) 2017-2020 - Raspberry Pi (Trading) Ltd. ++ * ++ * Dave Stevenson ++ * ++ * Based on TI am437x driver by ++ * Benoit Parrot ++ * Lad, Prabhakar ++ * ++ * and TI CAL camera interface driver by ++ * Benoit Parrot ++ * ++ * ++ * There are two camera drivers in the kernel for BCM283x - this one ++ * and bcm2835-camera (currently in staging). ++ * ++ * This driver directly controls the Unicam peripheral - there is no ++ * involvement with the VideoCore firmware. Unicam receives CSI-2 or ++ * CCP2 data and writes it into SDRAM. ++ * The only potential processing options are to repack Bayer data into an ++ * alternate format, and applying windowing. ++ * The repacking does not shift the data, so can repack V4L2_PIX_FMT_Sxxxx10P ++ * to V4L2_PIX_FMT_Sxxxx10, or V4L2_PIX_FMT_Sxxxx12P to V4L2_PIX_FMT_Sxxxx12, ++ * but not generically up to V4L2_PIX_FMT_Sxxxx16. The driver will add both ++ * formats where the relevant formats are defined, and will automatically ++ * configure the repacking as required. ++ * Support for windowing may be added later. ++ * ++ * It should be possible to connect this driver to any sensor with a ++ * suitable output interface and V4L2 subdevice driver. ++ * ++ * bcm2835-camera uses the VideoCore firmware to control the sensor, ++ * Unicam, ISP, and all tuner control loops. Fully processed frames are ++ * delivered to the driver by the firmware. It only has sensor drivers ++ * for Omnivision OV5647, and Sony IMX219 sensors. ++ * ++ * The two drivers are mutually exclusive for the same Unicam instance. ++ * The VideoCore firmware checks the device tree configuration during boot. ++ * If it finds device tree nodes called csi0 or csi1 it will block the ++ * firmware from accessing the peripheral, and bcm2835-camera will ++ * not be able to stream data. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "vc4-regs-unicam.h" ++ ++#define UNICAM_MODULE_NAME "unicam" ++#define UNICAM_VERSION "0.1.0" ++ ++static int debug; ++module_param(debug, int, 0644); ++MODULE_PARM_DESC(debug, "Debug level 0-3"); ++ ++#define unicam_dbg(level, dev, fmt, arg...) \ ++ v4l2_dbg(level, debug, &(dev)->v4l2_dev, fmt, ##arg) ++#define unicam_info(dev, fmt, arg...) \ ++ v4l2_info(&(dev)->v4l2_dev, fmt, ##arg) ++#define unicam_err(dev, fmt, arg...) \ ++ v4l2_err(&(dev)->v4l2_dev, fmt, ##arg) ++ ++/* To protect against a dodgy sensor driver never returning an error from ++ * enum_mbus_code, set a maximum index value to be used. ++ */ ++#define MAX_ENUM_MBUS_CODE 128 ++ ++/* ++ * Stride is a 16 bit register, but also has to be a multiple of 32. ++ */ ++#define BPL_ALIGNMENT 32 ++#define MAX_BYTESPERLINE ((1 << 16) - BPL_ALIGNMENT) ++/* ++ * Max width is therefore determined by the max stride divided by ++ * the number of bits per pixel. Take 32bpp as a ++ * worst case. ++ * No imposed limit on the height, so adopt a square image for want ++ * of anything better. ++ */ ++#define MAX_WIDTH (MAX_BYTESPERLINE / 4) ++#define MAX_HEIGHT MAX_WIDTH ++/* Define a nominal minimum image size */ ++#define MIN_WIDTH 16 ++#define MIN_HEIGHT 16 ++ ++/* ++ * struct unicam_fmt - Unicam media bus format information ++ * @pixelformat: V4L2 pixel format FCC identifier. 0 if n/a. ++ * @repacked_fourcc: V4L2 pixel format FCC identifier if the data is expanded ++ * out to 16bpp. 0 if n/a. ++ * @code: V4L2 media bus format code. ++ * @depth: Bits per pixel as delivered from the source. ++ * @csi_dt: CSI data type. ++ * @check_variants: Flag to denote that there are multiple mediabus formats ++ * still in the list that could match this V4L2 format. ++ */ ++struct unicam_fmt { ++ u32 fourcc; ++ u32 repacked_fourcc; ++ u32 code; ++ u8 depth; ++ u8 csi_dt; ++ u8 check_variants; ++}; ++ ++static const struct unicam_fmt formats[] = { ++ /* YUV Formats */ ++ { ++ .fourcc = V4L2_PIX_FMT_YUYV, ++ .code = MEDIA_BUS_FMT_YUYV8_2X8, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ .check_variants = 1, ++ }, { ++ .fourcc = V4L2_PIX_FMT_UYVY, ++ .code = MEDIA_BUS_FMT_UYVY8_2X8, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ .check_variants = 1, ++ }, { ++ .fourcc = V4L2_PIX_FMT_YVYU, ++ .code = MEDIA_BUS_FMT_YVYU8_2X8, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ .check_variants = 1, ++ }, { ++ .fourcc = V4L2_PIX_FMT_VYUY, ++ .code = MEDIA_BUS_FMT_VYUY8_2X8, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ .check_variants = 1, ++ }, { ++ .fourcc = V4L2_PIX_FMT_YUYV, ++ .code = MEDIA_BUS_FMT_YUYV8_1X16, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ }, { ++ .fourcc = V4L2_PIX_FMT_UYVY, ++ .code = MEDIA_BUS_FMT_UYVY8_1X16, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ }, { ++ .fourcc = V4L2_PIX_FMT_YVYU, ++ .code = MEDIA_BUS_FMT_YVYU8_1X16, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ }, { ++ .fourcc = V4L2_PIX_FMT_VYUY, ++ .code = MEDIA_BUS_FMT_VYUY8_1X16, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ }, { ++ /* RGB Formats */ ++ .fourcc = V4L2_PIX_FMT_RGB565, /* gggbbbbb rrrrrggg */ ++ .code = MEDIA_BUS_FMT_RGB565_2X8_LE, ++ .depth = 16, ++ .csi_dt = 0x22, ++ }, { ++ .fourcc = V4L2_PIX_FMT_RGB565X, /* rrrrrggg gggbbbbb */ ++ .code = MEDIA_BUS_FMT_RGB565_2X8_BE, ++ .depth = 16, ++ .csi_dt = 0x22 ++ }, { ++ .fourcc = V4L2_PIX_FMT_RGB555, /* gggbbbbb arrrrrgg */ ++ .code = MEDIA_BUS_FMT_RGB555_2X8_PADHI_LE, ++ .depth = 16, ++ .csi_dt = 0x21, ++ }, { ++ .fourcc = V4L2_PIX_FMT_RGB555X, /* arrrrrgg gggbbbbb */ ++ .code = MEDIA_BUS_FMT_RGB555_2X8_PADHI_BE, ++ .depth = 16, ++ .csi_dt = 0x21, ++ }, { ++ .fourcc = V4L2_PIX_FMT_RGB24, /* rgb */ ++ .code = MEDIA_BUS_FMT_RGB888_1X24, ++ .depth = 24, ++ .csi_dt = 0x24, ++ }, { ++ .fourcc = V4L2_PIX_FMT_BGR24, /* bgr */ ++ .code = MEDIA_BUS_FMT_BGR888_1X24, ++ .depth = 24, ++ .csi_dt = 0x24, ++ }, { ++ .fourcc = V4L2_PIX_FMT_RGB32, /* argb */ ++ .code = MEDIA_BUS_FMT_ARGB8888_1X32, ++ .depth = 32, ++ .csi_dt = 0x0, ++ }, { ++ /* Bayer Formats */ ++ .fourcc = V4L2_PIX_FMT_SBGGR8, ++ .code = MEDIA_BUS_FMT_SBGGR8_1X8, ++ .depth = 8, ++ .csi_dt = 0x2a, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGBRG8, ++ .code = MEDIA_BUS_FMT_SGBRG8_1X8, ++ .depth = 8, ++ .csi_dt = 0x2a, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGRBG8, ++ .code = MEDIA_BUS_FMT_SGRBG8_1X8, ++ .depth = 8, ++ .csi_dt = 0x2a, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SRGGB8, ++ .code = MEDIA_BUS_FMT_SRGGB8_1X8, ++ .depth = 8, ++ .csi_dt = 0x2a, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SBGGR10P, ++ .repacked_fourcc = V4L2_PIX_FMT_SBGGR10, ++ .code = MEDIA_BUS_FMT_SBGGR10_1X10, ++ .depth = 10, ++ .csi_dt = 0x2b, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGBRG10P, ++ .repacked_fourcc = V4L2_PIX_FMT_SGBRG10, ++ .code = MEDIA_BUS_FMT_SGBRG10_1X10, ++ .depth = 10, ++ .csi_dt = 0x2b, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGRBG10P, ++ .repacked_fourcc = V4L2_PIX_FMT_SGRBG10, ++ .code = MEDIA_BUS_FMT_SGRBG10_1X10, ++ .depth = 10, ++ .csi_dt = 0x2b, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SRGGB10P, ++ .repacked_fourcc = V4L2_PIX_FMT_SRGGB10, ++ .code = MEDIA_BUS_FMT_SRGGB10_1X10, ++ .depth = 10, ++ .csi_dt = 0x2b, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SBGGR12P, ++ .repacked_fourcc = V4L2_PIX_FMT_SBGGR12, ++ .code = MEDIA_BUS_FMT_SBGGR12_1X12, ++ .depth = 12, ++ .csi_dt = 0x2c, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGBRG12P, ++ .repacked_fourcc = V4L2_PIX_FMT_SGBRG12, ++ .code = MEDIA_BUS_FMT_SGBRG12_1X12, ++ .depth = 12, ++ .csi_dt = 0x2c, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGRBG12P, ++ .repacked_fourcc = V4L2_PIX_FMT_SGRBG12, ++ .code = MEDIA_BUS_FMT_SGRBG12_1X12, ++ .depth = 12, ++ .csi_dt = 0x2c, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SRGGB12P, ++ .repacked_fourcc = V4L2_PIX_FMT_SRGGB12, ++ .code = MEDIA_BUS_FMT_SRGGB12_1X12, ++ .depth = 12, ++ .csi_dt = 0x2c, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SBGGR14P, ++ .code = MEDIA_BUS_FMT_SBGGR14_1X14, ++ .depth = 14, ++ .csi_dt = 0x2d, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGBRG14P, ++ .code = MEDIA_BUS_FMT_SGBRG14_1X14, ++ .depth = 14, ++ .csi_dt = 0x2d, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGRBG14P, ++ .code = MEDIA_BUS_FMT_SGRBG14_1X14, ++ .depth = 14, ++ .csi_dt = 0x2d, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SRGGB14P, ++ .code = MEDIA_BUS_FMT_SRGGB14_1X14, ++ .depth = 14, ++ .csi_dt = 0x2d, ++ }, { ++ /* ++ * 16 bit Bayer formats could be supported, but there is no CSI2 ++ * data_type defined for raw 16, and no sensors that produce it at ++ * present. ++ */ ++ ++ /* Greyscale formats */ ++ .fourcc = V4L2_PIX_FMT_GREY, ++ .code = MEDIA_BUS_FMT_Y8_1X8, ++ .depth = 8, ++ .csi_dt = 0x2a, ++ }, { ++ .fourcc = V4L2_PIX_FMT_Y10P, ++ .repacked_fourcc = V4L2_PIX_FMT_Y10, ++ .code = MEDIA_BUS_FMT_Y10_1X10, ++ .depth = 10, ++ .csi_dt = 0x2b, ++ }, { ++ /* NB There is no packed V4L2 fourcc for this format. */ ++ .repacked_fourcc = V4L2_PIX_FMT_Y12, ++ .code = MEDIA_BUS_FMT_Y12_1X12, ++ .depth = 12, ++ .csi_dt = 0x2c, ++ }, ++}; ++ ++struct unicam_dmaqueue { ++ struct list_head active; ++}; ++ ++struct unicam_buffer { ++ struct vb2_v4l2_buffer vb; ++ struct list_head list; ++}; ++ ++struct unicam_cfg { ++ /* peripheral base address */ ++ void __iomem *base; ++ /* clock gating base address */ ++ void __iomem *clk_gate_base; ++}; ++ ++#define MAX_POSSIBLE_PIX_FMTS (ARRAY_SIZE(formats)) ++ ++struct unicam_device { ++ /* V4l2 specific parameters */ ++ /* Identifies video device for this channel */ ++ struct video_device video_dev; ++ struct v4l2_ctrl_handler ctrl_handler; ++ ++ struct v4l2_fwnode_endpoint endpoint; ++ ++ struct v4l2_async_subdev asd; ++ ++ /* unicam cfg */ ++ struct unicam_cfg cfg; ++ /* clock handle */ ++ struct clk *clock; ++ /* V4l2 device */ ++ struct v4l2_device v4l2_dev; ++ struct media_device mdev; ++ struct media_pad pad; ++ ++ /* parent device */ ++ struct platform_device *pdev; ++ /* subdevice async Notifier */ ++ struct v4l2_async_notifier notifier; ++ unsigned int sequence; ++ ++ /* ptr to sub device */ ++ struct v4l2_subdev *sensor; ++ /* Pad config for the sensor */ ++ struct v4l2_subdev_pad_config *sensor_config; ++ /* current input at the sub device */ ++ int current_input; ++ ++ /* Pointer pointing to current v4l2_buffer */ ++ struct unicam_buffer *cur_frm; ++ /* Pointer pointing to next v4l2_buffer */ ++ struct unicam_buffer *next_frm; ++ ++ /* video capture */ ++ const struct unicam_fmt *fmt; ++ /* Used to store current pixel format */ ++ struct v4l2_format v_fmt; ++ /* Used to store current mbus frame format */ ++ struct v4l2_mbus_framefmt m_fmt; ++ ++ unsigned int virtual_channel; ++ enum v4l2_mbus_type bus_type; ++ /* ++ * Stores bus.mipi_csi2.flags for CSI2 sensors, or ++ * bus.mipi_csi1.strobe for CCP2. ++ */ ++ unsigned int bus_flags; ++ unsigned int max_data_lanes; ++ unsigned int active_data_lanes; ++ ++ struct v4l2_rect crop; ++ ++ /* Currently selected input on subdev */ ++ int input; ++ ++ /* Buffer queue used in video-buf */ ++ struct vb2_queue buffer_queue; ++ /* Queue of filled frames */ ++ struct unicam_dmaqueue dma_queue; ++ /* IRQ lock for DMA queue */ ++ spinlock_t dma_queue_lock; ++ /* lock used to access this structure */ ++ struct mutex lock; ++ /* Flag to denote that we are processing buffers */ ++ int streaming; ++}; ++ ++/* Hardware access */ ++#define clk_write(dev, val) writel((val) | 0x5a000000, (dev)->clk_gate_base) ++#define clk_read(dev) readl((dev)->clk_gate_base) ++ ++#define reg_read(dev, offset) readl((dev)->base + (offset)) ++#define reg_write(dev, offset, val) writel(val, (dev)->base + (offset)) ++ ++#define reg_read_field(dev, offset, mask) get_field(reg_read((dev), (offset), \ ++ mask)) ++ ++static inline int get_field(u32 value, u32 mask) ++{ ++ return (value & mask) >> __ffs(mask); ++} ++ ++static inline void set_field(u32 *valp, u32 field, u32 mask) ++{ ++ u32 val = *valp; ++ ++ val &= ~mask; ++ val |= (field << __ffs(mask)) & mask; ++ *valp = val; ++} ++ ++static inline void reg_write_field(struct unicam_cfg *dev, u32 offset, ++ u32 field, u32 mask) ++{ ++ u32 val = reg_read((dev), (offset)); ++ ++ set_field(&val, field, mask); ++ reg_write((dev), (offset), val); ++} ++ ++/* Power management functions */ ++static inline int unicam_runtime_get(struct unicam_device *dev) ++{ ++ return pm_runtime_get_sync(&dev->pdev->dev); ++} ++ ++static inline void unicam_runtime_put(struct unicam_device *dev) ++{ ++ pm_runtime_put_sync(&dev->pdev->dev); ++} ++ ++/* Format setup functions */ ++static const struct unicam_fmt *find_format_by_code(u32 code) ++{ ++ unsigned int i; ++ ++ for (i = 0; i < ARRAY_SIZE(formats); i++) { ++ if (formats[i].code == code) ++ return &formats[i]; ++ } ++ ++ return NULL; ++} ++ ++static int check_mbus_format(struct unicam_device *dev, ++ const struct unicam_fmt *format) ++{ ++ struct v4l2_subdev_mbus_code_enum mbus_code; ++ int ret = 0; ++ int i; ++ ++ for (i = 0; !ret && i < MAX_ENUM_MBUS_CODE; i++) { ++ memset(&mbus_code, 0, sizeof(mbus_code)); ++ mbus_code.index = i; ++ mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, ++ NULL, &mbus_code); ++ ++ if (!ret && mbus_code.code == format->code) ++ return 1; ++ } ++ ++ return 0; ++} ++ ++static const struct unicam_fmt *find_format_by_pix(struct unicam_device *dev, ++ u32 pixelformat) ++{ ++ unsigned int i; ++ ++ for (i = 0; i < ARRAY_SIZE(formats); i++) { ++ if (formats[i].fourcc == pixelformat || ++ formats[i].repacked_fourcc == pixelformat) { ++ if (formats[i].check_variants && ++ !check_mbus_format(dev, &formats[i])) ++ continue; ++ return &formats[i]; ++ } ++ } ++ ++ return NULL; ++} ++ ++static inline unsigned int bytes_per_line(u32 width, ++ const struct unicam_fmt *fmt, ++ u32 v4l2_fourcc) ++{ ++ if (v4l2_fourcc == fmt->repacked_fourcc) ++ /* Repacking always goes to 16bpp */ ++ return ALIGN(width << 1, BPL_ALIGNMENT); ++ else ++ return ALIGN((width * fmt->depth) >> 3, BPL_ALIGNMENT); ++} ++ ++static int __subdev_get_format(struct unicam_device *dev, ++ struct v4l2_mbus_framefmt *fmt) ++{ ++ struct v4l2_subdev_format sd_fmt = { ++ .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ }; ++ int ret; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, get_fmt, dev->sensor_config, ++ &sd_fmt); ++ if (ret < 0) ++ return ret; ++ ++ *fmt = sd_fmt.format; ++ ++ unicam_dbg(1, dev, "%s %dx%d code:%04x\n", __func__, ++ fmt->width, fmt->height, fmt->code); ++ ++ return 0; ++} ++ ++static int __subdev_set_format(struct unicam_device *dev, ++ struct v4l2_mbus_framefmt *fmt) ++{ ++ struct v4l2_subdev_format sd_fmt = { ++ .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ }; ++ int ret; ++ ++ sd_fmt.format = *fmt; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, set_fmt, dev->sensor_config, ++ &sd_fmt); ++ if (ret < 0) ++ return ret; ++ ++ unicam_dbg(1, dev, "%s %dx%d code:%04x\n", __func__, ++ fmt->width, fmt->height, fmt->code); ++ ++ return 0; ++} ++ ++static int unicam_calc_format_size_bpl(struct unicam_device *dev, ++ const struct unicam_fmt *fmt, ++ struct v4l2_format *f) ++{ ++ unsigned int min_bytesperline; ++ ++ v4l_bound_align_image(&f->fmt.pix.width, MIN_WIDTH, MAX_WIDTH, 2, ++ &f->fmt.pix.height, MIN_HEIGHT, MAX_HEIGHT, 0, ++ 0); ++ ++ min_bytesperline = bytes_per_line(f->fmt.pix.width, fmt, ++ f->fmt.pix.pixelformat); ++ ++ if (f->fmt.pix.bytesperline > min_bytesperline && ++ f->fmt.pix.bytesperline <= MAX_BYTESPERLINE) ++ f->fmt.pix.bytesperline = ALIGN(f->fmt.pix.bytesperline, ++ BPL_ALIGNMENT); ++ else ++ f->fmt.pix.bytesperline = min_bytesperline; ++ ++ f->fmt.pix.sizeimage = f->fmt.pix.height * f->fmt.pix.bytesperline; ++ ++ unicam_dbg(3, dev, "%s: fourcc: %08X size: %dx%d bpl:%d img_size:%d\n", ++ __func__, ++ f->fmt.pix.pixelformat, ++ f->fmt.pix.width, f->fmt.pix.height, ++ f->fmt.pix.bytesperline, f->fmt.pix.sizeimage); ++ ++ return 0; ++} ++ ++static int unicam_reset_format(struct unicam_device *dev) ++{ ++ struct v4l2_mbus_framefmt mbus_fmt; ++ int ret; ++ ++ ret = __subdev_get_format(dev, &mbus_fmt); ++ if (ret) { ++ unicam_err(dev, "Failed to get_format - ret %d\n", ret); ++ return ret; ++ } ++ ++ if (mbus_fmt.code != dev->fmt->code) { ++ unicam_err(dev, "code mismatch - fmt->code %08x, mbus_fmt.code %08x\n", ++ dev->fmt->code, mbus_fmt.code); ++ return ret; ++ } ++ ++ v4l2_fill_pix_format(&dev->v_fmt.fmt.pix, &mbus_fmt); ++ dev->v_fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE; ++ ++ unicam_calc_format_size_bpl(dev, dev->fmt, &dev->v_fmt); ++ ++ dev->m_fmt = mbus_fmt; ++ ++ return 0; ++} ++ ++static void unicam_wr_dma_addr(struct unicam_device *dev, dma_addr_t dmaaddr) ++{ ++ /* ++ * dmaaddr should be a 32-bit address with the top two bits set to 0x3 ++ * to signify uncached access through the Videocore memory controller. ++ */ ++ BUG_ON((dmaaddr >> 30) != 0x3); ++ ++ reg_write(&dev->cfg, UNICAM_IBSA0, dmaaddr); ++ reg_write(&dev->cfg, UNICAM_IBEA0, ++ dmaaddr + dev->v_fmt.fmt.pix.sizeimage); ++} ++ ++static inline unsigned int unicam_get_lines_done(struct unicam_device *dev) ++{ ++ dma_addr_t start_addr, cur_addr; ++ unsigned int stride = dev->v_fmt.fmt.pix.bytesperline; ++ struct unicam_buffer *frm = dev->cur_frm; ++ ++ if (!frm) ++ return 0; ++ ++ start_addr = vb2_dma_contig_plane_dma_addr(&frm->vb.vb2_buf, 0); ++ cur_addr = reg_read(&dev->cfg, UNICAM_IBWP); ++ return (unsigned int)(cur_addr - start_addr) / stride; ++} ++ ++static inline void unicam_schedule_next_buffer(struct unicam_device *dev) ++{ ++ struct unicam_dmaqueue *dma_q = &dev->dma_queue; ++ struct unicam_buffer *buf; ++ dma_addr_t addr; ++ ++ buf = list_entry(dma_q->active.next, struct unicam_buffer, list); ++ dev->next_frm = buf; ++ list_del(&buf->list); ++ ++ addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0); ++ unicam_wr_dma_addr(dev, addr); ++} ++ ++static inline void unicam_process_buffer_complete(struct unicam_device *dev) ++{ ++ dev->cur_frm->vb.field = dev->m_fmt.field; ++ dev->cur_frm->vb.sequence = dev->sequence++; ++ ++ vb2_buffer_done(&dev->cur_frm->vb.vb2_buf, VB2_BUF_STATE_DONE); ++ dev->cur_frm = dev->next_frm; ++} ++ ++/* ++ * unicam_isr : ISR handler for unicam capture ++ * @irq: irq number ++ * @dev_id: dev_id ptr ++ * ++ * It changes status of the captured buffer, takes next buffer from the queue ++ * and sets its address in unicam registers ++ */ ++static irqreturn_t unicam_isr(int irq, void *dev) ++{ ++ struct unicam_device *unicam = (struct unicam_device *)dev; ++ struct unicam_cfg *cfg = &unicam->cfg; ++ struct unicam_dmaqueue *dma_q = &unicam->dma_queue; ++ unsigned int lines_done = unicam_get_lines_done(dev); ++ unsigned int sequence = unicam->sequence; ++ int ista, sta; ++ ++ /* ++ * Don't service interrupts if not streaming. ++ * Avoids issues if the VPU should enable the ++ * peripheral without the kernel knowing (that ++ * shouldn't happen, but causes issues if it does). ++ */ ++ if (!unicam->streaming) ++ return IRQ_HANDLED; ++ ++ sta = reg_read(cfg, UNICAM_STA); ++ /* Write value back to clear the interrupts */ ++ reg_write(cfg, UNICAM_STA, sta); ++ ++ ista = reg_read(cfg, UNICAM_ISTA); ++ /* Write value back to clear the interrupts */ ++ reg_write(cfg, UNICAM_ISTA, ista); ++ ++ unicam_dbg(3, unicam, "ISR: ISTA: 0x%X, STA: 0x%X, sequence %d, lines done %d", ++ ista, sta, sequence, lines_done); ++ ++ if (!(sta && (UNICAM_IS | UNICAM_PI0))) ++ return IRQ_HANDLED; ++ ++ if (ista & UNICAM_FSI) { ++ /* ++ * Timestamp is to be when the first data byte was captured, ++ * aka frame start. ++ */ ++ if (unicam->cur_frm) ++ unicam->cur_frm->vb.vb2_buf.timestamp = ktime_get_ns(); ++ } ++ if (ista & UNICAM_FEI || sta & UNICAM_PI0) { ++ /* ++ * Ensure we have swapped buffers already as we can't ++ * stop the peripheral. Overwrite the frame we've just ++ * captured instead. ++ */ ++ if (unicam->cur_frm && unicam->cur_frm != unicam->next_frm) ++ unicam_process_buffer_complete(unicam); ++ } ++ ++ /* Cannot swap buffer at frame end, there may be a race condition ++ * where the HW does not actually swap it if the new frame has ++ * already started. ++ */ ++ if (ista & (UNICAM_FSI | UNICAM_LCI) && !(ista & UNICAM_FEI)) { ++ spin_lock(&unicam->dma_queue_lock); ++ if (!list_empty(&dma_q->active) && ++ unicam->cur_frm == unicam->next_frm) ++ unicam_schedule_next_buffer(unicam); ++ spin_unlock(&unicam->dma_queue_lock); ++ } ++ ++ if (reg_read(&unicam->cfg, UNICAM_ICTL) & UNICAM_FCM) { ++ /* Switch out of trigger mode if selected */ ++ reg_write_field(&unicam->cfg, UNICAM_ICTL, 1, UNICAM_TFC); ++ reg_write_field(&unicam->cfg, UNICAM_ICTL, 0, UNICAM_FCM); ++ } ++ return IRQ_HANDLED; ++} ++ ++static int unicam_querycap(struct file *file, void *priv, ++ struct v4l2_capability *cap) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ ++ strlcpy(cap->driver, UNICAM_MODULE_NAME, sizeof(cap->driver)); ++ strlcpy(cap->card, UNICAM_MODULE_NAME, sizeof(cap->card)); ++ ++ snprintf(cap->bus_info, sizeof(cap->bus_info), ++ "platform:%s", dev->v4l2_dev.name); ++ ++ return 0; ++} ++ ++static int unicam_enum_fmt_vid_cap(struct file *file, void *priv, ++ struct v4l2_fmtdesc *f) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ struct v4l2_subdev_mbus_code_enum mbus_code; ++ const struct unicam_fmt *fmt = NULL; ++ int index = 0; ++ int ret = 0; ++ int i; ++ ++ for (i = 0; !ret && i < MAX_ENUM_MBUS_CODE; i++) { ++ memset(&mbus_code, 0, sizeof(mbus_code)); ++ mbus_code.index = i; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, ++ NULL, &mbus_code); ++ if (ret < 0) { ++ unicam_dbg(2, dev, ++ "subdev->enum_mbus_code idx %d returned %d - index invalid\n", ++ i, ret); ++ return -EINVAL; ++ } ++ ++ fmt = find_format_by_code(mbus_code.code); ++ if (fmt) { ++ if (fmt->fourcc) { ++ if (index == f->index) { ++ f->pixelformat = fmt->fourcc; ++ break; ++ } ++ index++; ++ } ++ if (fmt->repacked_fourcc) { ++ if (index == f->index) { ++ f->pixelformat = fmt->repacked_fourcc; ++ break; ++ } ++ index++; ++ } ++ } ++ } ++ ++ return 0; ++} ++ ++static int unicam_g_fmt_vid_cap(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ ++ *f = dev->v_fmt; ++ ++ return 0; ++} ++ ++static ++const struct unicam_fmt *get_first_supported_format(struct unicam_device *dev) ++{ ++ struct v4l2_subdev_mbus_code_enum mbus_code; ++ const struct unicam_fmt *fmt = NULL; ++ int ret; ++ int j; ++ ++ for (j = 0; ret != -EINVAL && ret != -ENOIOCTLCMD; ++j) { ++ memset(&mbus_code, 0, sizeof(mbus_code)); ++ mbus_code.index = j; ++ ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, NULL, ++ &mbus_code); ++ if (ret < 0) { ++ unicam_dbg(2, dev, ++ "subdev->enum_mbus_code idx %d returned %d - continue\n", ++ j, ret); ++ continue; ++ } ++ ++ unicam_dbg(2, dev, "subdev %s: code: 0x%08x idx: %d\n", ++ dev->sensor->name, mbus_code.code, j); ++ ++ fmt = find_format_by_code(mbus_code.code); ++ unicam_dbg(2, dev, "fmt 0x%08x returned as %p, V4L2 FOURCC 0x%08x, csi_dt 0x%02x\n", ++ mbus_code.code, fmt, fmt ? fmt->fourcc : 0, ++ fmt ? fmt->csi_dt : 0); ++ if (fmt) ++ return fmt; ++ } ++ ++ return NULL; ++} ++ ++static int unicam_try_fmt_vid_cap(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ struct v4l2_subdev_format sd_fmt = { ++ .which = V4L2_SUBDEV_FORMAT_TRY, ++ }; ++ struct v4l2_mbus_framefmt *mbus_fmt = &sd_fmt.format; ++ const struct unicam_fmt *fmt; ++ int ret; ++ ++ fmt = find_format_by_pix(dev, f->fmt.pix.pixelformat); ++ if (!fmt) { ++ /* Pixel format not supported by unicam. Choose the first ++ * supported format, and let the sensor choose something else. ++ */ ++ unicam_dbg(3, dev, "Fourcc format (0x%08x) not found. Use first format.\n", ++ f->fmt.pix.pixelformat); ++ ++ fmt = &formats[0]; ++ f->fmt.pix.pixelformat = fmt->fourcc; ++ } ++ ++ v4l2_fill_mbus_format(mbus_fmt, &f->fmt.pix, fmt->code); ++ /* ++ * No support for receiving interlaced video, so never ++ * request it from the sensor subdev. ++ */ ++ mbus_fmt->field = V4L2_FIELD_NONE; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, set_fmt, dev->sensor_config, ++ &sd_fmt); ++ if (ret && ret != -ENOIOCTLCMD && ret != -ENODEV) ++ return ret; ++ ++ if (mbus_fmt->field != V4L2_FIELD_NONE) ++ unicam_info(dev, "Sensor trying to send interlaced video - results may be unpredictable\n"); ++ ++ v4l2_fill_pix_format(&f->fmt.pix, &sd_fmt.format); ++ if (mbus_fmt->code != fmt->code) { ++ /* Sensor has returned an alternate format */ ++ fmt = find_format_by_code(mbus_fmt->code); ++ if (!fmt) { ++ /* The alternate format is one unicam can't support. ++ * Find the first format that is supported by both, and ++ * then set that. ++ */ ++ fmt = get_first_supported_format(dev); ++ mbus_fmt->code = fmt->code; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, set_fmt, ++ dev->sensor_config, &sd_fmt); ++ if (ret && ret != -ENOIOCTLCMD && ret != -ENODEV) ++ return ret; ++ ++ if (mbus_fmt->field != V4L2_FIELD_NONE) ++ unicam_info(dev, "Sensor trying to send interlaced video - results may be unpredictable\n"); ++ ++ v4l2_fill_pix_format(&f->fmt.pix, &sd_fmt.format); ++ ++ if (mbus_fmt->code != fmt->code) { ++ /* We've set a format that the sensor reports ++ * as being supported, but it refuses to set it. ++ * Not much else we can do. ++ * Assume that the sensor driver may accept the ++ * format when it is set (rather than tried). ++ */ ++ unicam_err(dev, "Sensor won't accept default format, and Unicam can't support sensor default\n"); ++ } ++ } ++ ++ if (fmt->fourcc) ++ f->fmt.pix.pixelformat = fmt->fourcc; ++ else ++ f->fmt.pix.pixelformat = fmt->repacked_fourcc; ++ } ++ ++ return unicam_calc_format_size_bpl(dev, fmt, f); ++} ++ ++static int unicam_s_fmt_vid_cap(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ struct vb2_queue *q = &dev->buffer_queue; ++ struct v4l2_mbus_framefmt mbus_fmt = {0}; ++ const struct unicam_fmt *fmt; ++ int ret; ++ ++ if (vb2_is_busy(q)) ++ return -EBUSY; ++ ++ ret = unicam_try_fmt_vid_cap(file, priv, f); ++ if (ret < 0) ++ return ret; ++ ++ fmt = find_format_by_pix(dev, f->fmt.pix.pixelformat); ++ if (!fmt) { ++ /* Unknown pixel format - adopt a default. ++ * This shouldn't happen as try_fmt should have resolved any ++ * issues first. ++ */ ++ fmt = get_first_supported_format(dev); ++ if (!fmt) ++ /* It shouldn't be possible to get here with no ++ * supported formats ++ */ ++ return -EINVAL; ++ f->fmt.pix.pixelformat = fmt->fourcc; ++ return -EINVAL; ++ } ++ ++ v4l2_fill_mbus_format(&mbus_fmt, &f->fmt.pix, fmt->code); ++ ++ ret = __subdev_set_format(dev, &mbus_fmt); ++ if (ret) { ++ unicam_dbg(3, dev, "%s __subdev_set_format failed %d\n", ++ __func__, ret); ++ return ret; ++ } ++ ++ /* Just double check nothing has gone wrong */ ++ if (mbus_fmt.code != fmt->code) { ++ unicam_dbg(3, dev, ++ "%s subdev changed format on us, this should not happen\n", ++ __func__); ++ return -EINVAL; ++ } ++ ++ dev->fmt = fmt; ++ dev->v_fmt.fmt.pix.pixelformat = f->fmt.pix.pixelformat; ++ dev->v_fmt.fmt.pix.bytesperline = f->fmt.pix.bytesperline; ++ unicam_reset_format(dev); ++ ++ unicam_dbg(3, dev, "%s %dx%d, mbus_fmt 0x%08X, V4L2 pix 0x%08X.\n", ++ __func__, dev->v_fmt.fmt.pix.width, ++ dev->v_fmt.fmt.pix.height, mbus_fmt.code, ++ dev->v_fmt.fmt.pix.pixelformat); ++ ++ *f = dev->v_fmt; ++ ++ return 0; ++} ++ ++static int unicam_queue_setup(struct vb2_queue *vq, ++ unsigned int *nbuffers, ++ unsigned int *nplanes, ++ unsigned int sizes[], ++ struct device *alloc_devs[]) ++{ ++ struct unicam_device *dev = vb2_get_drv_priv(vq); ++ unsigned int size = dev->v_fmt.fmt.pix.sizeimage; ++ ++ if (vq->num_buffers + *nbuffers < 3) ++ *nbuffers = 3 - vq->num_buffers; ++ ++ if (*nplanes) { ++ if (sizes[0] < size) { ++ unicam_err(dev, "sizes[0] %i < size %u\n", sizes[0], ++ size); ++ return -EINVAL; ++ } ++ size = sizes[0]; ++ } ++ ++ *nplanes = 1; ++ sizes[0] = size; ++ ++ return 0; ++} ++ ++static int unicam_buffer_prepare(struct vb2_buffer *vb) ++{ ++ struct unicam_device *dev = vb2_get_drv_priv(vb->vb2_queue); ++ struct unicam_buffer *buf = container_of(vb, struct unicam_buffer, ++ vb.vb2_buf); ++ unsigned long size; ++ ++ if (WARN_ON(!dev->fmt)) ++ return -EINVAL; ++ ++ size = dev->v_fmt.fmt.pix.sizeimage; ++ if (vb2_plane_size(vb, 0) < size) { ++ unicam_err(dev, "data will not fit into plane (%lu < %lu)\n", ++ vb2_plane_size(vb, 0), size); ++ return -EINVAL; ++ } ++ ++ vb2_set_plane_payload(&buf->vb.vb2_buf, 0, size); ++ return 0; ++} ++ ++static void unicam_buffer_queue(struct vb2_buffer *vb) ++{ ++ struct unicam_device *dev = vb2_get_drv_priv(vb->vb2_queue); ++ struct unicam_buffer *buf = container_of(vb, struct unicam_buffer, ++ vb.vb2_buf); ++ struct unicam_dmaqueue *dma_queue = &dev->dma_queue; ++ unsigned long flags = 0; ++ ++ spin_lock_irqsave(&dev->dma_queue_lock, flags); ++ list_add_tail(&buf->list, &dma_queue->active); ++ spin_unlock_irqrestore(&dev->dma_queue_lock, flags); ++} ++ ++static void unicam_set_packing_config(struct unicam_device *dev) ++{ ++ int pack, unpack; ++ u32 val; ++ ++ if (dev->v_fmt.fmt.pix.pixelformat == dev->fmt->fourcc) { ++ unpack = UNICAM_PUM_NONE; ++ pack = UNICAM_PPM_NONE; ++ } else { ++ switch (dev->fmt->depth) { ++ case 8: ++ unpack = UNICAM_PUM_UNPACK8; ++ break; ++ case 10: ++ unpack = UNICAM_PUM_UNPACK10; ++ break; ++ case 12: ++ unpack = UNICAM_PUM_UNPACK12; ++ break; ++ case 14: ++ unpack = UNICAM_PUM_UNPACK14; ++ break; ++ case 16: ++ unpack = UNICAM_PUM_UNPACK16; ++ break; ++ default: ++ unpack = UNICAM_PUM_NONE; ++ break; ++ } ++ ++ /* Repacking is always to 16bpp */ ++ pack = UNICAM_PPM_PACK16; ++ } ++ ++ val = 0; ++ set_field(&val, unpack, UNICAM_PUM_MASK); ++ set_field(&val, pack, UNICAM_PPM_MASK); ++ reg_write(&dev->cfg, UNICAM_IPIPE, val); ++} ++ ++static void unicam_cfg_image_id(struct unicam_device *dev) ++{ ++ struct unicam_cfg *cfg = &dev->cfg; ++ ++ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { ++ /* CSI2 mode */ ++ reg_write(cfg, UNICAM_IDI0, ++ (dev->virtual_channel << 6) | dev->fmt->csi_dt); ++ } else { ++ /* CCP2 mode */ ++ reg_write(cfg, UNICAM_IDI0, (0x80 | dev->fmt->csi_dt)); ++ } ++} ++ ++static void unicam_start_rx(struct unicam_device *dev, unsigned long addr) ++{ ++ struct unicam_cfg *cfg = &dev->cfg; ++ int line_int_freq = dev->v_fmt.fmt.pix.height >> 2; ++ unsigned int i; ++ u32 val; ++ ++ if (line_int_freq < 128) ++ line_int_freq = 128; ++ ++ /* Enable lane clocks */ ++ val = 1; ++ for (i = 0; i < dev->active_data_lanes; i++) ++ val = val << 2 | 1; ++ clk_write(cfg, val); ++ ++ /* Basic init */ ++ reg_write(cfg, UNICAM_CTRL, UNICAM_MEM); ++ ++ /* Enable analogue control, and leave in reset. */ ++ val = UNICAM_AR; ++ set_field(&val, 7, UNICAM_CTATADJ_MASK); ++ set_field(&val, 7, UNICAM_PTATADJ_MASK); ++ reg_write(cfg, UNICAM_ANA, val); ++ usleep_range(1000, 2000); ++ ++ /* Come out of reset */ ++ reg_write_field(cfg, UNICAM_ANA, 0, UNICAM_AR); ++ ++ /* Peripheral reset */ ++ reg_write_field(cfg, UNICAM_CTRL, 1, UNICAM_CPR); ++ reg_write_field(cfg, UNICAM_CTRL, 0, UNICAM_CPR); ++ ++ reg_write_field(cfg, UNICAM_CTRL, 0, UNICAM_CPE); ++ ++ /* Enable Rx control. */ ++ val = reg_read(cfg, UNICAM_CTRL); ++ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { ++ set_field(&val, UNICAM_CPM_CSI2, UNICAM_CPM_MASK); ++ set_field(&val, UNICAM_DCM_STROBE, UNICAM_DCM_MASK); ++ } else { ++ set_field(&val, UNICAM_CPM_CCP2, UNICAM_CPM_MASK); ++ set_field(&val, dev->bus_flags, UNICAM_DCM_MASK); ++ } ++ /* Packet framer timeout */ ++ set_field(&val, 0xf, UNICAM_PFT_MASK); ++ set_field(&val, 128, UNICAM_OET_MASK); ++ reg_write(cfg, UNICAM_CTRL, val); ++ ++ reg_write(cfg, UNICAM_IHWIN, 0); ++ reg_write(cfg, UNICAM_IVWIN, 0); ++ ++ /* AXI bus access QoS setup */ ++ val = reg_read(&dev->cfg, UNICAM_PRI); ++ set_field(&val, 0, UNICAM_BL_MASK); ++ set_field(&val, 0, UNICAM_BS_MASK); ++ set_field(&val, 0xe, UNICAM_PP_MASK); ++ set_field(&val, 8, UNICAM_NP_MASK); ++ set_field(&val, 2, UNICAM_PT_MASK); ++ set_field(&val, 1, UNICAM_PE); ++ reg_write(cfg, UNICAM_PRI, val); ++ ++ reg_write_field(cfg, UNICAM_ANA, 0, UNICAM_DDL); ++ ++ /* Always start in trigger frame capture mode (UNICAM_FCM set) */ ++ val = UNICAM_FSIE | UNICAM_FEIE | UNICAM_FCM; ++ set_field(&val, line_int_freq, UNICAM_LCIE_MASK); ++ reg_write(cfg, UNICAM_ICTL, val); ++ reg_write(cfg, UNICAM_STA, UNICAM_STA_MASK_ALL); ++ reg_write(cfg, UNICAM_ISTA, UNICAM_ISTA_MASK_ALL); ++ ++ /* tclk_term_en */ ++ reg_write_field(cfg, UNICAM_CLT, 2, UNICAM_CLT1_MASK); ++ /* tclk_settle */ ++ reg_write_field(cfg, UNICAM_CLT, 6, UNICAM_CLT2_MASK); ++ /* td_term_en */ ++ reg_write_field(cfg, UNICAM_DLT, 2, UNICAM_DLT1_MASK); ++ /* ths_settle */ ++ reg_write_field(cfg, UNICAM_DLT, 6, UNICAM_DLT2_MASK); ++ /* trx_enable */ ++ reg_write_field(cfg, UNICAM_DLT, 0, UNICAM_DLT3_MASK); ++ ++ reg_write_field(cfg, UNICAM_CTRL, 0, UNICAM_SOE); ++ ++ /* Packet compare setup - required to avoid missing frame ends */ ++ val = 0; ++ set_field(&val, 1, UNICAM_PCE); ++ set_field(&val, 1, UNICAM_GI); ++ set_field(&val, 1, UNICAM_CPH); ++ set_field(&val, 0, UNICAM_PCVC_MASK); ++ set_field(&val, 1, UNICAM_PCDT_MASK); ++ reg_write(cfg, UNICAM_CMP0, val); ++ ++ /* Enable clock lane and set up terminations */ ++ val = 0; ++ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { ++ /* CSI2 */ ++ set_field(&val, 1, UNICAM_CLE); ++ set_field(&val, 1, UNICAM_CLLPE); ++ if (dev->bus_flags & V4L2_MBUS_CSI2_CONTINUOUS_CLOCK) { ++ set_field(&val, 1, UNICAM_CLTRE); ++ set_field(&val, 1, UNICAM_CLHSE); ++ } ++ } else { ++ /* CCP2 */ ++ set_field(&val, 1, UNICAM_CLE); ++ set_field(&val, 1, UNICAM_CLHSE); ++ set_field(&val, 1, UNICAM_CLTRE); ++ } ++ reg_write(cfg, UNICAM_CLK, val); ++ ++ /* ++ * Enable required data lanes with appropriate terminations. ++ * The same value needs to be written to UNICAM_DATn registers for ++ * the active lanes, and 0 for inactive ones. ++ */ ++ val = 0; ++ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { ++ /* CSI2 */ ++ set_field(&val, 1, UNICAM_DLE); ++ set_field(&val, 1, UNICAM_DLLPE); ++ if (dev->bus_flags & V4L2_MBUS_CSI2_CONTINUOUS_CLOCK) { ++ set_field(&val, 1, UNICAM_DLTRE); ++ set_field(&val, 1, UNICAM_DLHSE); ++ } ++ } else { ++ /* CCP2 */ ++ set_field(&val, 1, UNICAM_DLE); ++ set_field(&val, 1, UNICAM_DLHSE); ++ set_field(&val, 1, UNICAM_DLTRE); ++ } ++ reg_write(cfg, UNICAM_DAT0, val); ++ ++ if (dev->active_data_lanes == 1) ++ val = 0; ++ reg_write(cfg, UNICAM_DAT1, val); ++ ++ if (dev->max_data_lanes > 2) { ++ /* ++ * Registers UNICAM_DAT2 and UNICAM_DAT3 only valid if the ++ * instance supports more than 2 data lanes. ++ */ ++ if (dev->active_data_lanes == 2) ++ val = 0; ++ reg_write(cfg, UNICAM_DAT2, val); ++ ++ if (dev->active_data_lanes == 3) ++ val = 0; ++ reg_write(cfg, UNICAM_DAT3, val); ++ } ++ ++ reg_write(&dev->cfg, UNICAM_IBLS, dev->v_fmt.fmt.pix.bytesperline); ++ unicam_wr_dma_addr(dev, addr); ++ unicam_set_packing_config(dev); ++ unicam_cfg_image_id(dev); ++ ++ /* Disabled embedded data */ ++ val = 0; ++ set_field(&val, 0, UNICAM_EDL_MASK); ++ reg_write(cfg, UNICAM_DCS, val); ++ ++ val = reg_read(cfg, UNICAM_MISC); ++ set_field(&val, 1, UNICAM_FL0); ++ set_field(&val, 1, UNICAM_FL1); ++ reg_write(cfg, UNICAM_MISC, val); ++ ++ /* Enable peripheral */ ++ reg_write_field(cfg, UNICAM_CTRL, 1, UNICAM_CPE); ++ ++ /* Load image pointers */ ++ reg_write_field(cfg, UNICAM_ICTL, 1, UNICAM_LIP_MASK); ++ ++ /* ++ * Enable trigger only for the first frame to ++ * sync correctly to the FS from the source. ++ */ ++ reg_write_field(cfg, UNICAM_ICTL, 1, UNICAM_TFC); ++} ++ ++static void unicam_disable(struct unicam_device *dev) ++{ ++ struct unicam_cfg *cfg = &dev->cfg; ++ ++ /* Analogue lane control disable */ ++ reg_write_field(cfg, UNICAM_ANA, 1, UNICAM_DDL); ++ ++ /* Stop the output engine */ ++ reg_write_field(cfg, UNICAM_CTRL, 1, UNICAM_SOE); ++ ++ /* Disable the data lanes. */ ++ reg_write(cfg, UNICAM_DAT0, 0); ++ reg_write(cfg, UNICAM_DAT1, 0); ++ ++ if (dev->max_data_lanes > 2) { ++ reg_write(cfg, UNICAM_DAT2, 0); ++ reg_write(cfg, UNICAM_DAT3, 0); ++ } ++ ++ /* Peripheral reset */ ++ reg_write_field(cfg, UNICAM_CTRL, 1, UNICAM_CPR); ++ usleep_range(50, 100); ++ reg_write_field(cfg, UNICAM_CTRL, 0, UNICAM_CPR); ++ ++ /* Disable peripheral */ ++ reg_write_field(cfg, UNICAM_CTRL, 0, UNICAM_CPE); ++ ++ /* Disable all lane clocks */ ++ clk_write(cfg, 0); ++} ++ ++static int unicam_start_streaming(struct vb2_queue *vq, unsigned int count) ++{ ++ struct unicam_device *dev = vb2_get_drv_priv(vq); ++ struct unicam_dmaqueue *dma_q = &dev->dma_queue; ++ struct unicam_buffer *buf, *tmp; ++ unsigned long addr = 0; ++ unsigned long flags; ++ int ret; ++ ++ spin_lock_irqsave(&dev->dma_queue_lock, flags); ++ buf = list_entry(dma_q->active.next, struct unicam_buffer, list); ++ dev->cur_frm = buf; ++ dev->next_frm = buf; ++ list_del(&buf->list); ++ spin_unlock_irqrestore(&dev->dma_queue_lock, flags); ++ ++ addr = vb2_dma_contig_plane_dma_addr(&dev->cur_frm->vb.vb2_buf, 0); ++ dev->sequence = 0; ++ ++ ret = unicam_runtime_get(dev); ++ if (ret < 0) { ++ unicam_dbg(3, dev, "unicam_runtime_get failed\n"); ++ goto err_release_buffers; ++ } ++ ++ dev->active_data_lanes = dev->max_data_lanes; ++ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY && ++ v4l2_subdev_has_op(dev->sensor, video, g_mbus_config)) { ++ struct v4l2_mbus_config mbus_config; ++ ++ ret = v4l2_subdev_call(dev->sensor, video, g_mbus_config, ++ &mbus_config); ++ if (ret < 0) { ++ unicam_dbg(3, dev, "g_mbus_config failed\n"); ++ goto err_pm_put; ++ } ++ ++ dev->active_data_lanes = ++ (mbus_config.flags & V4L2_MBUS_CSI2_LANE_MASK) >> ++ __ffs(V4L2_MBUS_CSI2_LANE_MASK); ++ if (!dev->active_data_lanes) ++ dev->active_data_lanes = dev->max_data_lanes; ++ } ++ if (dev->active_data_lanes > dev->max_data_lanes) { ++ unicam_err(dev, "Device has requested %u data lanes, which is >%u configured in DT\n", ++ dev->active_data_lanes, dev->max_data_lanes); ++ ret = -EINVAL; ++ goto err_pm_put; ++ } ++ ++ unicam_dbg(1, dev, "Running with %u data lanes\n", ++ dev->active_data_lanes); ++ ++ ret = clk_set_rate(dev->clock, 100 * 1000 * 1000); ++ if (ret) { ++ unicam_err(dev, "failed to set up clock\n"); ++ goto err_pm_put; ++ } ++ ++ ret = clk_prepare_enable(dev->clock); ++ if (ret) { ++ unicam_err(dev, "Failed to enable CSI clock: %d\n", ret); ++ goto err_pm_put; ++ } ++ dev->streaming = 1; ++ ++ unicam_start_rx(dev, addr); ++ ++ ret = v4l2_subdev_call(dev->sensor, video, s_stream, 1); ++ if (ret < 0) { ++ unicam_err(dev, "stream on failed in subdev\n"); ++ goto err_disable_unicam; ++ } ++ ++ return 0; ++ ++err_disable_unicam: ++ unicam_disable(dev); ++ clk_disable_unprepare(dev->clock); ++err_pm_put: ++ unicam_runtime_put(dev); ++err_release_buffers: ++ list_for_each_entry_safe(buf, tmp, &dma_q->active, list) { ++ list_del(&buf->list); ++ vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); ++ } ++ if (dev->cur_frm != dev->next_frm) ++ vb2_buffer_done(&dev->next_frm->vb.vb2_buf, ++ VB2_BUF_STATE_QUEUED); ++ vb2_buffer_done(&dev->cur_frm->vb.vb2_buf, VB2_BUF_STATE_QUEUED); ++ dev->next_frm = NULL; ++ dev->cur_frm = NULL; ++ ++ return ret; ++} ++ ++static void unicam_stop_streaming(struct vb2_queue *vq) ++{ ++ struct unicam_device *dev = vb2_get_drv_priv(vq); ++ struct unicam_dmaqueue *dma_q = &dev->dma_queue; ++ struct unicam_buffer *buf, *tmp; ++ unsigned long flags; ++ ++ if (v4l2_subdev_call(dev->sensor, video, s_stream, 0) < 0) ++ unicam_err(dev, "stream off failed in subdev\n"); ++ ++ unicam_disable(dev); ++ ++ /* Release all active buffers */ ++ spin_lock_irqsave(&dev->dma_queue_lock, flags); ++ list_for_each_entry_safe(buf, tmp, &dma_q->active, list) { ++ list_del(&buf->list); ++ vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); ++ } ++ ++ if (dev->cur_frm == dev->next_frm) { ++ vb2_buffer_done(&dev->cur_frm->vb.vb2_buf, VB2_BUF_STATE_ERROR); ++ } else { ++ vb2_buffer_done(&dev->cur_frm->vb.vb2_buf, VB2_BUF_STATE_ERROR); ++ vb2_buffer_done(&dev->next_frm->vb.vb2_buf, ++ VB2_BUF_STATE_ERROR); ++ } ++ dev->cur_frm = NULL; ++ dev->next_frm = NULL; ++ spin_unlock_irqrestore(&dev->dma_queue_lock, flags); ++ ++ clk_disable_unprepare(dev->clock); ++ unicam_runtime_put(dev); ++} ++ ++static int unicam_enum_input(struct file *file, void *priv, ++ struct v4l2_input *inp) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ ++ if (inp->index != 0) ++ return -EINVAL; ++ ++ inp->type = V4L2_INPUT_TYPE_CAMERA; ++ if (v4l2_subdev_has_op(dev->sensor, video, s_dv_timings)) { ++ inp->capabilities = V4L2_IN_CAP_DV_TIMINGS; ++ inp->std = 0; ++ } else if (v4l2_subdev_has_op(dev->sensor, video, s_std)) { ++ inp->capabilities = V4L2_IN_CAP_STD; ++ if (v4l2_subdev_call(dev->sensor, video, g_tvnorms, &inp->std) ++ < 0) ++ inp->std = V4L2_STD_ALL; ++ } else { ++ inp->capabilities = 0; ++ inp->std = 0; ++ } ++ sprintf(inp->name, "Camera 0"); ++ return 0; ++} ++ ++static int unicam_g_input(struct file *file, void *priv, unsigned int *i) ++{ ++ *i = 0; ++ ++ return 0; ++} ++ ++static int unicam_s_input(struct file *file, void *priv, unsigned int i) ++{ ++ /* ++ * FIXME: Ideally we would like to be able to query the source ++ * subdevice for information over the input connectors it supports, ++ * and map that through in to a call to video_ops->s_routing. ++ * There is no infrastructure support for defining that within ++ * devicetree at present. Until that is implemented we can't ++ * map a user physical connector number to s_routing input number. ++ */ ++ if (i > 0) ++ return -EINVAL; ++ ++ return 0; ++} ++ ++static int unicam_querystd(struct file *file, void *priv, ++ v4l2_std_id *std) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ ++ return v4l2_subdev_call(dev->sensor, video, querystd, std); ++} ++ ++static int unicam_g_std(struct file *file, void *priv, v4l2_std_id *std) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ ++ return v4l2_subdev_call(dev->sensor, video, g_std, std); ++} ++ ++static int unicam_s_std(struct file *file, void *priv, v4l2_std_id std) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ int ret; ++ v4l2_std_id current_std; ++ ++ ret = v4l2_subdev_call(dev->sensor, video, g_std, ¤t_std); ++ if (ret) ++ return ret; ++ ++ if (std == current_std) ++ return 0; ++ ++ if (vb2_is_busy(&dev->buffer_queue)) ++ return -EBUSY; ++ ++ ret = v4l2_subdev_call(dev->sensor, video, s_std, std); ++ ++ /* Force recomputation of bytesperline */ ++ dev->v_fmt.fmt.pix.bytesperline = 0; ++ ++ unicam_reset_format(dev); ++ ++ return ret; ++} ++ ++static int unicam_s_edid(struct file *file, void *priv, struct v4l2_edid *edid) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ ++ return v4l2_subdev_call(dev->sensor, pad, set_edid, edid); ++} ++ ++static int unicam_g_edid(struct file *file, void *priv, struct v4l2_edid *edid) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ ++ return v4l2_subdev_call(dev->sensor, pad, get_edid, edid); ++} ++ ++static int unicam_enum_framesizes(struct file *file, void *priv, ++ struct v4l2_frmsizeenum *fsize) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ const struct unicam_fmt *fmt; ++ struct v4l2_subdev_frame_size_enum fse; ++ int ret; ++ ++ /* check for valid format */ ++ fmt = find_format_by_pix(dev, fsize->pixel_format); ++ if (!fmt) { ++ unicam_dbg(3, dev, "Invalid pixel code: %x\n", ++ fsize->pixel_format); ++ return -EINVAL; ++ } ++ ++ fse.index = fsize->index; ++ fse.pad = 0; ++ fse.code = fmt->code; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, enum_frame_size, NULL, &fse); ++ if (ret) ++ return ret; ++ ++ unicam_dbg(1, dev, "%s: index: %d code: %x W:[%d,%d] H:[%d,%d]\n", ++ __func__, fse.index, fse.code, fse.min_width, fse.max_width, ++ fse.min_height, fse.max_height); ++ ++ fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE; ++ fsize->discrete.width = fse.max_width; ++ fsize->discrete.height = fse.max_height; ++ ++ return 0; ++} ++ ++static int unicam_enum_frameintervals(struct file *file, void *priv, ++ struct v4l2_frmivalenum *fival) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ const struct unicam_fmt *fmt; ++ struct v4l2_subdev_frame_interval_enum fie = { ++ .index = fival->index, ++ .width = fival->width, ++ .height = fival->height, ++ .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ }; ++ int ret; ++ ++ fmt = find_format_by_pix(dev, fival->pixel_format); ++ if (!fmt) ++ return -EINVAL; ++ ++ fie.code = fmt->code; ++ ret = v4l2_subdev_call(dev->sensor, pad, enum_frame_interval, ++ NULL, &fie); ++ if (ret) ++ return ret; ++ ++ fival->type = V4L2_FRMIVAL_TYPE_DISCRETE; ++ fival->discrete = fie.interval; ++ ++ return 0; ++} ++ ++static int unicam_g_parm(struct file *file, void *fh, struct v4l2_streamparm *a) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ ++ return v4l2_g_parm_cap(video_devdata(file), dev->sensor, a); ++} ++ ++static int unicam_s_parm(struct file *file, void *fh, struct v4l2_streamparm *a) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ ++ return v4l2_s_parm_cap(video_devdata(file), dev->sensor, a); ++} ++ ++static int unicam_g_dv_timings(struct file *file, void *priv, ++ struct v4l2_dv_timings *timings) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ ++ return v4l2_subdev_call(dev->sensor, video, g_dv_timings, timings); ++} ++ ++static int unicam_s_dv_timings(struct file *file, void *priv, ++ struct v4l2_dv_timings *timings) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ struct v4l2_dv_timings current_timings; ++ int ret; ++ ++ ret = v4l2_subdev_call(dev->sensor, video, g_dv_timings, ++ ¤t_timings); ++ ++ if (v4l2_match_dv_timings(timings, ¤t_timings, 0, false)) ++ return 0; ++ ++ if (vb2_is_busy(&dev->buffer_queue)) ++ return -EBUSY; ++ ++ ret = v4l2_subdev_call(dev->sensor, video, s_dv_timings, timings); ++ ++ /* Force recomputation of bytesperline */ ++ dev->v_fmt.fmt.pix.bytesperline = 0; ++ ++ unicam_reset_format(dev); ++ ++ return ret; ++} ++ ++static int unicam_query_dv_timings(struct file *file, void *priv, ++ struct v4l2_dv_timings *timings) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ ++ return v4l2_subdev_call(dev->sensor, video, query_dv_timings, timings); ++} ++ ++static int unicam_enum_dv_timings(struct file *file, void *priv, ++ struct v4l2_enum_dv_timings *timings) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ ++ return v4l2_subdev_call(dev->sensor, pad, enum_dv_timings, timings); ++} ++ ++static int unicam_dv_timings_cap(struct file *file, void *priv, ++ struct v4l2_dv_timings_cap *cap) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ ++ return v4l2_subdev_call(dev->sensor, pad, dv_timings_cap, cap); ++} ++ ++static int unicam_subscribe_event(struct v4l2_fh *fh, ++ const struct v4l2_event_subscription *sub) ++{ ++ switch (sub->type) { ++ case V4L2_EVENT_SOURCE_CHANGE: ++ return v4l2_event_subscribe(fh, sub, 4, NULL); ++ } ++ ++ return v4l2_ctrl_subscribe_event(fh, sub); ++} ++ ++static int unicam_log_status(struct file *file, void *fh) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ struct unicam_cfg *cfg = &dev->cfg; ++ u32 reg; ++ ++ /* status for sub devices */ ++ v4l2_device_call_all(&dev->v4l2_dev, 0, core, log_status); ++ ++ unicam_info(dev, "-----Receiver status-----\n"); ++ unicam_info(dev, "V4L2 width/height: %ux%u\n", ++ dev->v_fmt.fmt.pix.width, dev->v_fmt.fmt.pix.height); ++ unicam_info(dev, "Mediabus format: %08x\n", dev->fmt->code); ++ unicam_info(dev, "V4L2 format: %08x\n", ++ dev->v_fmt.fmt.pix.pixelformat); ++ reg = reg_read(&dev->cfg, UNICAM_IPIPE); ++ unicam_info(dev, "Unpacking/packing: %u / %u\n", ++ get_field(reg, UNICAM_PUM_MASK), ++ get_field(reg, UNICAM_PPM_MASK)); ++ unicam_info(dev, "----Live data----\n"); ++ unicam_info(dev, "Programmed stride: %4u\n", ++ reg_read(cfg, UNICAM_IBLS)); ++ unicam_info(dev, "Detected resolution: %ux%u\n", ++ reg_read(cfg, UNICAM_IHSTA), ++ reg_read(cfg, UNICAM_IVSTA)); ++ unicam_info(dev, "Write pointer: %08x\n", ++ reg_read(cfg, UNICAM_IBWP)); ++ ++ return 0; ++} ++ ++static void unicam_notify(struct v4l2_subdev *sd, ++ unsigned int notification, void *arg) ++{ ++ struct unicam_device *dev = ++ container_of(sd->v4l2_dev, struct unicam_device, v4l2_dev); ++ ++ switch (notification) { ++ case V4L2_DEVICE_NOTIFY_EVENT: ++ v4l2_event_queue(&dev->video_dev, arg); ++ break; ++ default: ++ break; ++ } ++} ++ ++static const struct vb2_ops unicam_video_qops = { ++ .wait_prepare = vb2_ops_wait_prepare, ++ .wait_finish = vb2_ops_wait_finish, ++ .queue_setup = unicam_queue_setup, ++ .buf_prepare = unicam_buffer_prepare, ++ .buf_queue = unicam_buffer_queue, ++ .start_streaming = unicam_start_streaming, ++ .stop_streaming = unicam_stop_streaming, ++}; ++ ++/* ++ * unicam_open : This function is based on the v4l2_fh_open helper function. ++ * It has been augmented to handle sensor subdevice power management, ++ */ ++static int unicam_open(struct file *file) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ int ret; ++ ++ mutex_lock(&dev->lock); ++ ++ ret = v4l2_fh_open(file); ++ if (ret) { ++ unicam_err(dev, "v4l2_fh_open failed\n"); ++ goto unlock; ++ } ++ ++ if (!v4l2_fh_is_singular_file(file)) ++ goto unlock; ++ ++ ret = v4l2_subdev_call(dev->sensor, core, s_power, 1); ++ if (ret < 0 && ret != -ENOIOCTLCMD) { ++ v4l2_fh_release(file); ++ goto unlock; ++ } ++ ++ ret = 0; ++ ++unlock: ++ mutex_unlock(&dev->lock); ++ return ret; ++} ++ ++static int unicam_release(struct file *file) ++{ ++ struct unicam_device *dev = video_drvdata(file); ++ struct v4l2_subdev *sd = dev->sensor; ++ bool fh_singular; ++ int ret; ++ ++ mutex_lock(&dev->lock); ++ ++ fh_singular = v4l2_fh_is_singular_file(file); ++ ++ ret = _vb2_fop_release(file, NULL); ++ ++ if (fh_singular) ++ v4l2_subdev_call(sd, core, s_power, 0); ++ ++ mutex_unlock(&dev->lock); ++ ++ return ret; ++} ++ ++/* unicam capture driver file operations */ ++static const struct v4l2_file_operations unicam_fops = { ++ .owner = THIS_MODULE, ++ .open = unicam_open, ++ .release = unicam_release, ++ .read = vb2_fop_read, ++ .poll = vb2_fop_poll, ++ .unlocked_ioctl = video_ioctl2, ++ .mmap = vb2_fop_mmap, ++}; ++ ++/* unicam capture ioctl operations */ ++static const struct v4l2_ioctl_ops unicam_ioctl_ops = { ++ .vidioc_querycap = unicam_querycap, ++ .vidioc_enum_fmt_vid_cap = unicam_enum_fmt_vid_cap, ++ .vidioc_g_fmt_vid_cap = unicam_g_fmt_vid_cap, ++ .vidioc_s_fmt_vid_cap = unicam_s_fmt_vid_cap, ++ .vidioc_try_fmt_vid_cap = unicam_try_fmt_vid_cap, ++ ++ .vidioc_enum_input = unicam_enum_input, ++ .vidioc_g_input = unicam_g_input, ++ .vidioc_s_input = unicam_s_input, ++ ++ .vidioc_querystd = unicam_querystd, ++ .vidioc_s_std = unicam_s_std, ++ .vidioc_g_std = unicam_g_std, ++ ++ .vidioc_g_edid = unicam_g_edid, ++ .vidioc_s_edid = unicam_s_edid, ++ ++ .vidioc_enum_framesizes = unicam_enum_framesizes, ++ .vidioc_enum_frameintervals = unicam_enum_frameintervals, ++ ++ .vidioc_g_parm = unicam_g_parm, ++ .vidioc_s_parm = unicam_s_parm, ++ ++ .vidioc_s_dv_timings = unicam_s_dv_timings, ++ .vidioc_g_dv_timings = unicam_g_dv_timings, ++ .vidioc_query_dv_timings = unicam_query_dv_timings, ++ .vidioc_enum_dv_timings = unicam_enum_dv_timings, ++ .vidioc_dv_timings_cap = unicam_dv_timings_cap, ++ ++ .vidioc_reqbufs = vb2_ioctl_reqbufs, ++ .vidioc_create_bufs = vb2_ioctl_create_bufs, ++ .vidioc_prepare_buf = vb2_ioctl_prepare_buf, ++ .vidioc_querybuf = vb2_ioctl_querybuf, ++ .vidioc_qbuf = vb2_ioctl_qbuf, ++ .vidioc_dqbuf = vb2_ioctl_dqbuf, ++ .vidioc_expbuf = vb2_ioctl_expbuf, ++ .vidioc_streamon = vb2_ioctl_streamon, ++ .vidioc_streamoff = vb2_ioctl_streamoff, ++ ++ .vidioc_log_status = unicam_log_status, ++ .vidioc_subscribe_event = unicam_subscribe_event, ++ .vidioc_unsubscribe_event = v4l2_event_unsubscribe, ++}; ++ ++static int ++unicam_async_bound(struct v4l2_async_notifier *notifier, ++ struct v4l2_subdev *subdev, ++ struct v4l2_async_subdev *asd) ++{ ++ struct unicam_device *unicam = container_of(notifier->v4l2_dev, ++ struct unicam_device, v4l2_dev); ++ ++ if (unicam->sensor) { ++ unicam_info(unicam, "Rejecting subdev %s (Already set!!)", ++ subdev->name); ++ return 0; ++ } ++ ++ unicam->sensor = subdev; ++ unicam_dbg(1, unicam, "Using sensor %s for capture\n", subdev->name); ++ ++ return 0; ++} ++ ++static int unicam_probe_complete(struct unicam_device *unicam) ++{ ++ struct video_device *vdev; ++ struct vb2_queue *q; ++ struct v4l2_mbus_framefmt mbus_fmt = {0}; ++ const struct unicam_fmt *fmt; ++ int ret; ++ ++ v4l2_set_subdev_hostdata(unicam->sensor, unicam); ++ ++ unicam->v4l2_dev.notify = unicam_notify; ++ ++ unicam->sensor_config = v4l2_subdev_alloc_pad_config(unicam->sensor); ++ if (!unicam->sensor_config) ++ return -ENOMEM; ++ ++ ret = __subdev_get_format(unicam, &mbus_fmt); ++ if (ret) { ++ unicam_err(unicam, "Failed to get_format - ret %d\n", ret); ++ return ret; ++ } ++ ++ fmt = find_format_by_code(mbus_fmt.code); ++ if (!fmt) { ++ /* Find the first format that the sensor and unicam both ++ * support ++ */ ++ fmt = get_first_supported_format(unicam); ++ ++ if (!fmt) ++ /* No compatible formats */ ++ return -EINVAL; ++ ++ mbus_fmt.code = fmt->code; ++ ret = __subdev_set_format(unicam, &mbus_fmt); ++ if (ret) ++ return -EINVAL; ++ } ++ if (mbus_fmt.field != V4L2_FIELD_NONE) { ++ /* Interlaced not supported - disable it now. */ ++ mbus_fmt.field = V4L2_FIELD_NONE; ++ ret = __subdev_set_format(unicam, &mbus_fmt); ++ if (ret) ++ return -EINVAL; ++ } ++ ++ unicam->fmt = fmt; ++ if (fmt->fourcc) ++ unicam->v_fmt.fmt.pix.pixelformat = fmt->fourcc; ++ else ++ unicam->v_fmt.fmt.pix.pixelformat = fmt->repacked_fourcc; ++ ++ /* Read current subdev format */ ++ unicam_reset_format(unicam); ++ ++ if (v4l2_subdev_has_op(unicam->sensor, video, s_std)) { ++ v4l2_std_id tvnorms; ++ ++ if (WARN_ON(!v4l2_subdev_has_op(unicam->sensor, video, ++ g_tvnorms))) ++ /* ++ * Subdevice should not advertise s_std but not ++ * g_tvnorms ++ */ ++ return -EINVAL; ++ ++ ret = v4l2_subdev_call(unicam->sensor, video, ++ g_tvnorms, &tvnorms); ++ if (WARN_ON(ret)) ++ return -EINVAL; ++ unicam->video_dev.tvnorms |= tvnorms; ++ } ++ ++ spin_lock_init(&unicam->dma_queue_lock); ++ mutex_init(&unicam->lock); ++ ++ /* Add controls from the subdevice */ ++ ret = v4l2_ctrl_add_handler(&unicam->ctrl_handler, ++ unicam->sensor->ctrl_handler, NULL, true); ++ if (ret < 0) ++ return ret; ++ ++ q = &unicam->buffer_queue; ++ q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; ++ q->io_modes = VB2_MMAP | VB2_DMABUF | VB2_READ; ++ q->drv_priv = unicam; ++ q->ops = &unicam_video_qops; ++ q->mem_ops = &vb2_dma_contig_memops; ++ q->buf_struct_size = sizeof(struct unicam_buffer); ++ q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC; ++ q->lock = &unicam->lock; ++ q->min_buffers_needed = 2; ++ q->dev = &unicam->pdev->dev; ++ ++ ret = vb2_queue_init(q); ++ if (ret) { ++ unicam_err(unicam, "vb2_queue_init() failed\n"); ++ return ret; ++ } ++ ++ INIT_LIST_HEAD(&unicam->dma_queue.active); ++ ++ vdev = &unicam->video_dev; ++ strlcpy(vdev->name, UNICAM_MODULE_NAME, sizeof(vdev->name)); ++ vdev->release = video_device_release_empty; ++ vdev->fops = &unicam_fops; ++ vdev->ioctl_ops = &unicam_ioctl_ops; ++ vdev->v4l2_dev = &unicam->v4l2_dev; ++ vdev->vfl_dir = VFL_DIR_RX; ++ vdev->queue = q; ++ vdev->lock = &unicam->lock; ++ vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING | ++ V4L2_CAP_READWRITE; ++ ++ /* If the source has no controls then remove our ctrl handler. */ ++ if (list_empty(&unicam->ctrl_handler.ctrls)) ++ unicam->v4l2_dev.ctrl_handler = NULL; ++ ++ video_set_drvdata(vdev, unicam); ++ vdev->entity.flags |= MEDIA_ENT_FL_DEFAULT; ++ ++ if (!v4l2_subdev_has_op(unicam->sensor, video, s_std)) { ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_S_STD); ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_G_STD); ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_ENUMSTD); ++ } ++ if (!v4l2_subdev_has_op(unicam->sensor, video, querystd)) ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_QUERYSTD); ++ if (!v4l2_subdev_has_op(unicam->sensor, video, s_dv_timings)) { ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_S_EDID); ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_G_EDID); ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_DV_TIMINGS_CAP); ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_G_DV_TIMINGS); ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_S_DV_TIMINGS); ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_ENUM_DV_TIMINGS); ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_QUERY_DV_TIMINGS); ++ } ++ if (!v4l2_subdev_has_op(unicam->sensor, pad, enum_frame_interval)) ++ v4l2_disable_ioctl(&unicam->video_dev, ++ VIDIOC_ENUM_FRAMEINTERVALS); ++ if (!v4l2_subdev_has_op(unicam->sensor, video, g_frame_interval)) ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_G_PARM); ++ if (!v4l2_subdev_has_op(unicam->sensor, video, s_frame_interval)) ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_S_PARM); ++ ++ if (!v4l2_subdev_has_op(unicam->sensor, pad, enum_frame_size)) ++ v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_ENUM_FRAMESIZES); ++ ++ ret = video_register_device(vdev, VFL_TYPE_VIDEO, -1); ++ if (ret) { ++ unicam_err(unicam, "Unable to register video device.\n"); ++ return ret; ++ } ++ ++ ret = v4l2_device_register_ro_subdev_nodes(&unicam->v4l2_dev); ++ if (ret) { ++ unicam_err(unicam, ++ "Unable to register subdev nodes.\n"); ++ video_unregister_device(&unicam->video_dev); ++ return ret; ++ } ++ ++ ret = media_create_pad_link(&unicam->sensor->entity, 0, ++ &unicam->video_dev.entity, 0, ++ MEDIA_LNK_FL_ENABLED | ++ MEDIA_LNK_FL_IMMUTABLE); ++ if (ret) { ++ unicam_err(unicam, "Unable to create pad links.\n"); ++ video_unregister_device(&unicam->video_dev); ++ return ret; ++ } ++ ++ return 0; ++} ++ ++static int unicam_async_complete(struct v4l2_async_notifier *notifier) ++{ ++ struct unicam_device *unicam = container_of(notifier->v4l2_dev, ++ struct unicam_device, v4l2_dev); ++ ++ return unicam_probe_complete(unicam); ++} ++ ++static const struct v4l2_async_notifier_operations unicam_async_ops = { ++ .bound = unicam_async_bound, ++ .complete = unicam_async_complete, ++}; ++ ++static int of_unicam_connect_subdevs(struct unicam_device *dev) ++{ ++ struct platform_device *pdev = dev->pdev; ++ struct device_node *parent, *ep_node = NULL, *remote_ep = NULL, ++ *sensor_node = NULL; ++ struct v4l2_fwnode_endpoint *ep; ++ struct v4l2_async_subdev *asd; ++ unsigned int peripheral_data_lanes; ++ int ret = -EINVAL; ++ unsigned int lane; ++ ++ parent = pdev->dev.of_node; ++ ++ asd = &dev->asd; ++ ep = &dev->endpoint; ++ ++ ep_node = of_graph_get_next_endpoint(parent, NULL); ++ if (!ep_node) { ++ unicam_dbg(3, dev, "can't get next endpoint\n"); ++ goto cleanup_exit; ++ } ++ ++ unicam_dbg(3, dev, "ep_node is %s\n", ep_node->name); ++ ++ v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep_node), ep); ++ ++ for (lane = 0; lane < ep->bus.mipi_csi2.num_data_lanes; lane++) { ++ if (ep->bus.mipi_csi2.data_lanes[lane] != lane + 1) { ++ unicam_err(dev, "Local endpoint - data lane reordering not supported\n"); ++ goto cleanup_exit; ++ } ++ } ++ ++ peripheral_data_lanes = ep->bus.mipi_csi2.num_data_lanes; ++ ++ sensor_node = of_graph_get_remote_port_parent(ep_node); ++ if (!sensor_node) { ++ unicam_dbg(3, dev, "can't get remote parent\n"); ++ goto cleanup_exit; ++ } ++ unicam_dbg(3, dev, "sensor_node is %s\n", sensor_node->name); ++ asd->match_type = V4L2_ASYNC_MATCH_FWNODE; ++ asd->match.fwnode = of_fwnode_handle(sensor_node); ++ ++ remote_ep = of_graph_get_remote_endpoint(ep_node); ++ if (!remote_ep) { ++ unicam_dbg(3, dev, "can't get remote-endpoint\n"); ++ goto cleanup_exit; ++ } ++ unicam_dbg(3, dev, "remote_ep is %s\n", remote_ep->name); ++ v4l2_fwnode_endpoint_parse(of_fwnode_handle(remote_ep), ep); ++ unicam_dbg(3, dev, "parsed remote_ep to endpoint. nr_of_link_frequencies %u, bus_type %u\n", ++ ep->nr_of_link_frequencies, ep->bus_type); ++ ++ switch (ep->bus_type) { ++ case V4L2_MBUS_CSI2_DPHY: ++ if (ep->bus.mipi_csi2.num_data_lanes > ++ peripheral_data_lanes) { ++ unicam_err(dev, "Subdevice %s wants too many data lanes (%u > %u)\n", ++ sensor_node->name, ++ ep->bus.mipi_csi2.num_data_lanes, ++ peripheral_data_lanes); ++ goto cleanup_exit; ++ } ++ for (lane = 0; ++ lane < ep->bus.mipi_csi2.num_data_lanes; ++ lane++) { ++ if (ep->bus.mipi_csi2.data_lanes[lane] != lane + 1) { ++ unicam_err(dev, "Subdevice %s - incompatible data lane config\n", ++ sensor_node->name); ++ goto cleanup_exit; ++ } ++ } ++ dev->max_data_lanes = ep->bus.mipi_csi2.num_data_lanes; ++ dev->bus_flags = ep->bus.mipi_csi2.flags; ++ break; ++ case V4L2_MBUS_CCP2: ++ if (ep->bus.mipi_csi1.clock_lane != 0 || ++ ep->bus.mipi_csi1.data_lane != 1) { ++ unicam_err(dev, "Subdevice %s incompatible lane config\n", ++ sensor_node->name); ++ goto cleanup_exit; ++ } ++ dev->max_data_lanes = 1; ++ dev->bus_flags = ep->bus.mipi_csi1.strobe; ++ break; ++ default: ++ /* Unsupported bus type */ ++ unicam_err(dev, "sub-device %s is not a CSI2 or CCP2 device %d\n", ++ sensor_node->name, ep->bus_type); ++ goto cleanup_exit; ++ } ++ ++ /* Store bus type - CSI2 or CCP2 */ ++ dev->bus_type = ep->bus_type; ++ unicam_dbg(3, dev, "bus_type is %d\n", dev->bus_type); ++ ++ /* Store Virtual Channel number */ ++ dev->virtual_channel = ep->base.id; ++ ++ unicam_dbg(3, dev, "v4l2-endpoint: %s\n", ++ dev->bus_type == V4L2_MBUS_CSI2_DPHY ? "CSI2" : "CCP2"); ++ unicam_dbg(3, dev, "Virtual Channel=%d\n", dev->virtual_channel); ++ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) ++ unicam_dbg(3, dev, "flags=0x%08x\n", ep->bus.mipi_csi2.flags); ++ unicam_dbg(3, dev, "num_data_lanes=%d\n", dev->max_data_lanes); ++ ++ unicam_dbg(1, dev, "found sub-device %s\n", sensor_node->name); ++ ++ v4l2_async_notifier_init(&dev->notifier); ++ ++ ret = v4l2_async_notifier_add_subdev(&dev->notifier, asd); ++ if (ret) { ++ unicam_err(dev, "Error adding subdevice - ret %d\n", ret); ++ goto cleanup_exit; ++ } ++ ++ dev->notifier.ops = &unicam_async_ops; ++ ret = v4l2_async_notifier_register(&dev->v4l2_dev, ++ &dev->notifier); ++ if (ret) { ++ unicam_err(dev, "Error registering async notifier - ret %d\n", ++ ret); ++ ret = -EINVAL; ++ } ++ ++cleanup_exit: ++ if (remote_ep) ++ of_node_put(remote_ep); ++ if (sensor_node) ++ of_node_put(sensor_node); ++ if (ep_node) ++ of_node_put(ep_node); ++ ++ return ret; ++} ++ ++static int unicam_probe(struct platform_device *pdev) ++{ ++ struct unicam_cfg *unicam_cfg; ++ struct unicam_device *unicam; ++ struct v4l2_ctrl_handler *hdl; ++ struct resource *res; ++ int ret; ++ ++ unicam = devm_kzalloc(&pdev->dev, sizeof(*unicam), GFP_KERNEL); ++ if (!unicam) ++ return -ENOMEM; ++ ++ unicam->pdev = pdev; ++ unicam_cfg = &unicam->cfg; ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 0); ++ unicam_cfg->base = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(unicam_cfg->base)) { ++ unicam_err(unicam, "Failed to get main io block\n"); ++ return PTR_ERR(unicam_cfg->base); ++ } ++ ++ res = platform_get_resource(pdev, IORESOURCE_MEM, 1); ++ unicam_cfg->clk_gate_base = devm_ioremap_resource(&pdev->dev, res); ++ if (IS_ERR(unicam_cfg->clk_gate_base)) { ++ unicam_err(unicam, "Failed to get 2nd io block\n"); ++ return PTR_ERR(unicam_cfg->clk_gate_base); ++ } ++ ++ unicam->clock = devm_clk_get(&pdev->dev, "lp"); ++ if (IS_ERR(unicam->clock)) { ++ unicam_err(unicam, "Failed to get clock\n"); ++ return PTR_ERR(unicam->clock); ++ } ++ ++ ret = platform_get_irq(pdev, 0); ++ if (ret <= 0) { ++ dev_err(&pdev->dev, "No IRQ resource\n"); ++ return -ENODEV; ++ } ++ ++ ret = devm_request_irq(&pdev->dev, ret, unicam_isr, 0, ++ "unicam_capture0", unicam); ++ if (ret) { ++ dev_err(&pdev->dev, "Unable to request interrupt\n"); ++ return -EINVAL; ++ } ++ ++ unicam->mdev.dev = &pdev->dev; ++ strscpy(unicam->mdev.model, UNICAM_MODULE_NAME, ++ sizeof(unicam->mdev.model)); ++ strscpy(unicam->mdev.serial, "", sizeof(unicam->mdev.serial)); ++ snprintf(unicam->mdev.bus_info, sizeof(unicam->mdev.bus_info), ++ "platform:%s %s", ++ pdev->dev.driver->name, dev_name(&pdev->dev)); ++ unicam->mdev.hw_revision = 1; ++ ++ media_entity_pads_init(&unicam->video_dev.entity, 1, &unicam->pad); ++ media_device_init(&unicam->mdev); ++ ++ unicam->v4l2_dev.mdev = &unicam->mdev; ++ ++ ret = v4l2_device_register(&pdev->dev, &unicam->v4l2_dev); ++ if (ret) { ++ unicam_err(unicam, ++ "Unable to register v4l2 device.\n"); ++ goto media_cleanup; ++ } ++ ++ ret = media_device_register(&unicam->mdev); ++ if (ret < 0) { ++ unicam_err(unicam, ++ "Unable to register media-controller device.\n"); ++ goto probe_out_v4l2_unregister; ++ } ++ ++ /* Reserve space for the controls */ ++ hdl = &unicam->ctrl_handler; ++ ret = v4l2_ctrl_handler_init(hdl, 16); ++ if (ret < 0) ++ goto media_unregister; ++ unicam->v4l2_dev.ctrl_handler = hdl; ++ ++ /* set the driver data in platform device */ ++ platform_set_drvdata(pdev, unicam); ++ ++ ret = of_unicam_connect_subdevs(unicam); ++ if (ret) { ++ dev_err(&pdev->dev, "Failed to connect subdevs\n"); ++ goto free_hdl; ++ } ++ ++ /* Enable the block power domain */ ++ pm_runtime_enable(&pdev->dev); ++ ++ return 0; ++ ++free_hdl: ++ v4l2_ctrl_handler_free(hdl); ++media_unregister: ++ media_device_unregister(&unicam->mdev); ++probe_out_v4l2_unregister: ++ v4l2_device_unregister(&unicam->v4l2_dev); ++media_cleanup: ++ media_device_cleanup(&unicam->mdev); ++ ++ return ret; ++} ++ ++static int unicam_remove(struct platform_device *pdev) ++{ ++ struct unicam_device *unicam = platform_get_drvdata(pdev); ++ ++ unicam_dbg(2, unicam, "%s\n", __func__); ++ ++ pm_runtime_disable(&pdev->dev); ++ ++ v4l2_async_notifier_unregister(&unicam->notifier); ++ v4l2_ctrl_handler_free(&unicam->ctrl_handler); ++ v4l2_device_unregister(&unicam->v4l2_dev); ++ video_unregister_device(&unicam->video_dev); ++ if (unicam->sensor_config) ++ v4l2_subdev_free_pad_config(unicam->sensor_config); ++ media_device_unregister(&unicam->mdev); ++ media_device_cleanup(&unicam->mdev); ++ ++ return 0; ++} ++ ++static const struct of_device_id unicam_of_match[] = { ++ { .compatible = "brcm,bcm2835-unicam", }, ++ { /* sentinel */ }, ++}; ++MODULE_DEVICE_TABLE(of, unicam_of_match); ++ ++static struct platform_driver unicam_driver = { ++ .probe = unicam_probe, ++ .remove = unicam_remove, ++ .driver = { ++ .name = UNICAM_MODULE_NAME, ++ .of_match_table = of_match_ptr(unicam_of_match), ++ }, ++}; ++ ++module_platform_driver(unicam_driver); ++ ++MODULE_AUTHOR("Dave Stevenson "); ++MODULE_DESCRIPTION("BCM2835 Unicam driver"); ++MODULE_LICENSE("GPL"); ++MODULE_VERSION(UNICAM_VERSION); +--- /dev/null ++++ b/drivers/media/platform/bcm2835/vc4-regs-unicam.h +@@ -0,0 +1,253 @@ ++/* SPDX-License-Identifier: GPL-2.0-only */ ++ ++/* ++ * Copyright (C) 2017-2020 Raspberry Pi Trading. ++ * Dave Stevenson ++ */ ++ ++#ifndef VC4_REGS_UNICAM_H ++#define VC4_REGS_UNICAM_H ++ ++/* ++ * The following values are taken from files found within the code drop ++ * made by Broadcom for the BCM21553 Graphics Driver, predominantly in ++ * brcm_usrlib/dag/vmcsx/vcinclude/hardware_vc4.h. ++ * They have been modified to be only the register offset. ++ */ ++#define UNICAM_CTRL 0x000 ++#define UNICAM_STA 0x004 ++#define UNICAM_ANA 0x008 ++#define UNICAM_PRI 0x00c ++#define UNICAM_CLK 0x010 ++#define UNICAM_CLT 0x014 ++#define UNICAM_DAT0 0x018 ++#define UNICAM_DAT1 0x01c ++#define UNICAM_DAT2 0x020 ++#define UNICAM_DAT3 0x024 ++#define UNICAM_DLT 0x028 ++#define UNICAM_CMP0 0x02c ++#define UNICAM_CMP1 0x030 ++#define UNICAM_CAP0 0x034 ++#define UNICAM_CAP1 0x038 ++#define UNICAM_ICTL 0x100 ++#define UNICAM_ISTA 0x104 ++#define UNICAM_IDI0 0x108 ++#define UNICAM_IPIPE 0x10c ++#define UNICAM_IBSA0 0x110 ++#define UNICAM_IBEA0 0x114 ++#define UNICAM_IBLS 0x118 ++#define UNICAM_IBWP 0x11c ++#define UNICAM_IHWIN 0x120 ++#define UNICAM_IHSTA 0x124 ++#define UNICAM_IVWIN 0x128 ++#define UNICAM_IVSTA 0x12c ++#define UNICAM_ICC 0x130 ++#define UNICAM_ICS 0x134 ++#define UNICAM_IDC 0x138 ++#define UNICAM_IDPO 0x13c ++#define UNICAM_IDCA 0x140 ++#define UNICAM_IDCD 0x144 ++#define UNICAM_IDS 0x148 ++#define UNICAM_DCS 0x200 ++#define UNICAM_DBSA0 0x204 ++#define UNICAM_DBEA0 0x208 ++#define UNICAM_DBWP 0x20c ++#define UNICAM_DBCTL 0x300 ++#define UNICAM_IBSA1 0x304 ++#define UNICAM_IBEA1 0x308 ++#define UNICAM_IDI1 0x30c ++#define UNICAM_DBSA1 0x310 ++#define UNICAM_DBEA1 0x314 ++#define UNICAM_MISC 0x400 ++ ++/* ++ * The following bitmasks are from the kernel released by Broadcom ++ * for Android - https://android.googlesource.com/kernel/bcm/ ++ * The Rhea, Hawaii, and Java chips all contain the same VideoCore4 ++ * Unicam block as BCM2835, as defined in eg ++ * arch/arm/mach-rhea/include/mach/rdb_A0/brcm_rdb_cam.h and similar. ++ * Values reworked to use the kernel BIT and GENMASK macros. ++ * ++ * Some of the bit mnenomics have been amended to match the datasheet. ++ */ ++/* UNICAM_CTRL Register */ ++#define UNICAM_CPE BIT(0) ++#define UNICAM_MEM BIT(1) ++#define UNICAM_CPR BIT(2) ++#define UNICAM_CPM_MASK GENMASK(3, 3) ++#define UNICAM_CPM_CSI2 0 ++#define UNICAM_CPM_CCP2 1 ++#define UNICAM_SOE BIT(4) ++#define UNICAM_DCM_MASK GENMASK(5, 5) ++#define UNICAM_DCM_STROBE 0 ++#define UNICAM_DCM_DATA 1 ++#define UNICAM_SLS BIT(6) ++#define UNICAM_PFT_MASK GENMASK(11, 8) ++#define UNICAM_OET_MASK GENMASK(20, 12) ++ ++/* UNICAM_STA Register */ ++#define UNICAM_SYN BIT(0) ++#define UNICAM_CS BIT(1) ++#define UNICAM_SBE BIT(2) ++#define UNICAM_PBE BIT(3) ++#define UNICAM_HOE BIT(4) ++#define UNICAM_PLE BIT(5) ++#define UNICAM_SSC BIT(6) ++#define UNICAM_CRCE BIT(7) ++#define UNICAM_OES BIT(8) ++#define UNICAM_IFO BIT(9) ++#define UNICAM_OFO BIT(10) ++#define UNICAM_BFO BIT(11) ++#define UNICAM_DL BIT(12) ++#define UNICAM_PS BIT(13) ++#define UNICAM_IS BIT(14) ++#define UNICAM_PI0 BIT(15) ++#define UNICAM_PI1 BIT(16) ++#define UNICAM_FSI_S BIT(17) ++#define UNICAM_FEI_S BIT(18) ++#define UNICAM_LCI_S BIT(19) ++#define UNICAM_BUF0_RDY BIT(20) ++#define UNICAM_BUF0_NO BIT(21) ++#define UNICAM_BUF1_RDY BIT(22) ++#define UNICAM_BUF1_NO BIT(23) ++#define UNICAM_DI BIT(24) ++ ++#define UNICAM_STA_MASK_ALL \ ++ (UNICAM_DL + \ ++ UNICAM_SBE + \ ++ UNICAM_PBE + \ ++ UNICAM_HOE + \ ++ UNICAM_PLE + \ ++ UNICAM_SSC + \ ++ UNICAM_CRCE + \ ++ UNICAM_IFO + \ ++ UNICAM_OFO + \ ++ UNICAM_PS + \ ++ UNICAM_PI0 + \ ++ UNICAM_PI1) ++ ++/* UNICAM_ANA Register */ ++#define UNICAM_APD BIT(0) ++#define UNICAM_BPD BIT(1) ++#define UNICAM_AR BIT(2) ++#define UNICAM_DDL BIT(3) ++#define UNICAM_CTATADJ_MASK GENMASK(7, 4) ++#define UNICAM_PTATADJ_MASK GENMASK(11, 8) ++ ++/* UNICAM_PRI Register */ ++#define UNICAM_PE BIT(0) ++#define UNICAM_PT_MASK GENMASK(2, 1) ++#define UNICAM_NP_MASK GENMASK(7, 4) ++#define UNICAM_PP_MASK GENMASK(11, 8) ++#define UNICAM_BS_MASK GENMASK(15, 12) ++#define UNICAM_BL_MASK GENMASK(17, 16) ++ ++/* UNICAM_CLK Register */ ++#define UNICAM_CLE BIT(0) ++#define UNICAM_CLPD BIT(1) ++#define UNICAM_CLLPE BIT(2) ++#define UNICAM_CLHSE BIT(3) ++#define UNICAM_CLTRE BIT(4) ++#define UNICAM_CLAC_MASK GENMASK(8, 5) ++#define UNICAM_CLSTE BIT(29) ++ ++/* UNICAM_CLT Register */ ++#define UNICAM_CLT1_MASK GENMASK(7, 0) ++#define UNICAM_CLT2_MASK GENMASK(15, 8) ++ ++/* UNICAM_DATn Registers */ ++#define UNICAM_DLE BIT(0) ++#define UNICAM_DLPD BIT(1) ++#define UNICAM_DLLPE BIT(2) ++#define UNICAM_DLHSE BIT(3) ++#define UNICAM_DLTRE BIT(4) ++#define UNICAM_DLSM BIT(5) ++#define UNICAM_DLFO BIT(28) ++#define UNICAM_DLSTE BIT(29) ++ ++#define UNICAM_DAT_MASK_ALL (UNICAM_DLSTE + UNICAM_DLFO) ++ ++/* UNICAM_DLT Register */ ++#define UNICAM_DLT1_MASK GENMASK(7, 0) ++#define UNICAM_DLT2_MASK GENMASK(15, 8) ++#define UNICAM_DLT3_MASK GENMASK(23, 16) ++ ++/* UNICAM_ICTL Register */ ++#define UNICAM_FSIE BIT(0) ++#define UNICAM_FEIE BIT(1) ++#define UNICAM_IBOB BIT(2) ++#define UNICAM_FCM BIT(3) ++#define UNICAM_TFC BIT(4) ++#define UNICAM_LIP_MASK GENMASK(6, 5) ++#define UNICAM_LCIE_MASK GENMASK(28, 16) ++ ++/* UNICAM_IDI0/1 Register */ ++#define UNICAM_ID0_MASK GENMASK(7, 0) ++#define UNICAM_ID1_MASK GENMASK(15, 8) ++#define UNICAM_ID2_MASK GENMASK(23, 16) ++#define UNICAM_ID3_MASK GENMASK(31, 24) ++ ++/* UNICAM_ISTA Register */ ++#define UNICAM_FSI BIT(0) ++#define UNICAM_FEI BIT(1) ++#define UNICAM_LCI BIT(2) ++ ++#define UNICAM_ISTA_MASK_ALL (UNICAM_FSI + UNICAM_FEI + UNICAM_LCI) ++ ++/* UNICAM_IPIPE Register */ ++#define UNICAM_PUM_MASK GENMASK(2, 0) ++ /* Unpacking modes */ ++ #define UNICAM_PUM_NONE 0 ++ #define UNICAM_PUM_UNPACK6 1 ++ #define UNICAM_PUM_UNPACK7 2 ++ #define UNICAM_PUM_UNPACK8 3 ++ #define UNICAM_PUM_UNPACK10 4 ++ #define UNICAM_PUM_UNPACK12 5 ++ #define UNICAM_PUM_UNPACK14 6 ++ #define UNICAM_PUM_UNPACK16 7 ++#define UNICAM_DDM_MASK GENMASK(6, 3) ++#define UNICAM_PPM_MASK GENMASK(9, 7) ++ /* Packing modes */ ++ #define UNICAM_PPM_NONE 0 ++ #define UNICAM_PPM_PACK8 1 ++ #define UNICAM_PPM_PACK10 2 ++ #define UNICAM_PPM_PACK12 3 ++ #define UNICAM_PPM_PACK14 4 ++ #define UNICAM_PPM_PACK16 5 ++#define UNICAM_DEM_MASK GENMASK(11, 10) ++#define UNICAM_DEBL_MASK GENMASK(14, 12) ++#define UNICAM_ICM_MASK GENMASK(16, 15) ++#define UNICAM_IDM_MASK GENMASK(17, 17) ++ ++/* UNICAM_ICC Register */ ++#define UNICAM_ICFL_MASK GENMASK(4, 0) ++#define UNICAM_ICFH_MASK GENMASK(9, 5) ++#define UNICAM_ICST_MASK GENMASK(12, 10) ++#define UNICAM_ICLT_MASK GENMASK(15, 13) ++#define UNICAM_ICLL_MASK GENMASK(31, 16) ++ ++/* UNICAM_DCS Register */ ++#define UNICAM_DIE BIT(0) ++#define UNICAM_DIM BIT(1) ++#define UNICAM_DBOB BIT(3) ++#define UNICAM_FDE BIT(4) ++#define UNICAM_LDP BIT(5) ++#define UNICAM_EDL_MASK GENMASK(15, 8) ++ ++/* UNICAM_DBCTL Register */ ++#define UNICAM_DBEN BIT(0) ++#define UNICAM_BUF0_IE BIT(1) ++#define UNICAM_BUF1_IE BIT(2) ++ ++/* UNICAM_CMP[0,1] register */ ++#define UNICAM_PCE BIT(31) ++#define UNICAM_GI BIT(9) ++#define UNICAM_CPH BIT(8) ++#define UNICAM_PCVC_MASK GENMASK(7, 6) ++#define UNICAM_PCDT_MASK GENMASK(5, 0) ++ ++/* UNICAM_MISC register */ ++#define UNICAM_FL0 BIT(6) ++#define UNICAM_FL1 BIT(9) ++ ++#endif diff --git a/target/linux/bcm27xx/patches-5.10/950-0210-media-uapi-v4l2-core-Add-sensor-ancillary-data-V4L2-.patch b/target/linux/bcm27xx/patches-5.10/950-0210-media-uapi-v4l2-core-Add-sensor-ancillary-data-V4L2-.patch new file mode 100644 index 0000000000..a89ce1a8d6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0210-media-uapi-v4l2-core-Add-sensor-ancillary-data-V4L2-.patch @@ -0,0 +1,85 @@ +From 2f43e72bd136b5e69dbc6453555d8c5fecbb9d3a Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Wed, 1 Apr 2020 08:46:29 +0100 +Subject: [PATCH] media: uapi: v4l2-core: Add sensor ancillary data + V4L2 foucc type. + +Add V4L2_META_FMT_SENSOR_DATA format 4CC. + +This new format will be used by the BCM2835 Unicam device to return +out camera sensor embedded data. + +Signed-off-by: Naushir Patuck +--- + .../userspace-api/media/v4l/meta-formats.rst | 1 + + .../media/v4l/pixfmt-meta-sensor-data.rst | 32 +++++++++++++++++++ + drivers/media/v4l2-core/v4l2-ioctl.c | 1 + + include/uapi/linux/videodev2.h | 1 + + 4 files changed, 35 insertions(+) + create mode 100644 Documentation/userspace-api/media/v4l/pixfmt-meta-sensor-data.rst + +--- a/Documentation/userspace-api/media/v4l/meta-formats.rst ++++ b/Documentation/userspace-api/media/v4l/meta-formats.rst +@@ -15,6 +15,7 @@ These formats are used for the :ref:`met + pixfmt-meta-d4xx + pixfmt-meta-intel-ipu3 + pixfmt-meta-rkisp1 ++ pixfmt-meta-sensor-data + pixfmt-meta-uvc + pixfmt-meta-vsp1-hgo + pixfmt-meta-vsp1-hgt +--- /dev/null ++++ b/Documentation/userspace-api/media/v4l/pixfmt-meta-sensor-data.rst +@@ -0,0 +1,32 @@ ++.. Permission is granted to copy, distribute and/or modify this ++.. document under the terms of the GNU Free Documentation License, ++.. Version 1.1 or any later version published by the Free Software ++.. Foundation, with no Invariant Sections, no Front-Cover Texts ++.. and no Back-Cover Texts. A copy of the license is included at ++.. Documentation/media/uapi/fdl-appendix.rst. ++.. ++.. TODO: replace it to GFDL-1.1-or-later WITH no-invariant-sections ++ ++.. _v4l2-meta-fmt-sensor-data: ++ ++*********************************** ++V4L2_META_FMT_SENSOR_DATA ('SENS') ++*********************************** ++ ++Sensor Ancillary Metadata ++ ++Description ++=========== ++ ++This format describes ancillary data generated by a camera sensor and ++transmitted over a stream on the camera bus. Sensor vendors generally have their ++own custom format for this ancillary data. Some vendors follow a generic ++CSI-2/SMIA embedded data format as described in the `CSI-2 specification. ++`_ ++ ++The size of the embedded buffer is defined as a single line with a pixel width ++width specified in bytes. This is obtained by a call to the ++:c:type:`VIDIOC_SUBDEV_G_FMT` ioctl on the sensor subdevice where the ``pad`` ++field in :c:type:`v4l2_subdev_format` is set to 1. Note that this size is fixed ++and cannot be modified with a call to :c:type:`VIDIOC_SUBDEV_S_FMT`. ++ +--- a/drivers/media/v4l2-core/v4l2-ioctl.c ++++ b/drivers/media/v4l2-core/v4l2-ioctl.c +@@ -1404,6 +1404,7 @@ static void v4l_fill_fmtdesc(struct v4l2 + case V4L2_META_FMT_UVC: descr = "UVC Payload Header Metadata"; break; + case V4L2_META_FMT_D4XX: descr = "Intel D4xx UVC Metadata"; break; + case V4L2_META_FMT_VIVID: descr = "Vivid Metadata"; break; ++ case V4L2_META_FMT_SENSOR_DATA: descr = "Sensor Ancillary Metadata"; break; + + default: + /* Compressed formats */ +--- a/include/uapi/linux/videodev2.h ++++ b/include/uapi/linux/videodev2.h +@@ -778,6 +778,7 @@ struct v4l2_pix_format { + #define V4L2_META_FMT_UVC v4l2_fourcc('U', 'V', 'C', 'H') /* UVC Payload Header metadata */ + #define V4L2_META_FMT_D4XX v4l2_fourcc('D', '4', 'X', 'X') /* D4XX Payload Header metadata */ + #define V4L2_META_FMT_VIVID v4l2_fourcc('V', 'I', 'V', 'D') /* Vivid Metadata */ ++#define V4L2_META_FMT_SENSOR_DATA v4l2_fourcc('S', 'E', 'N', 'S') /* Sensor Ancillary metadata */ + + /* priv field value to indicates that subsequent fields are valid. */ + #define V4L2_PIX_FMT_PRIV_MAGIC 0xfeedcafe diff --git a/target/linux/bcm27xx/patches-5.10/950-0211-media-uapi-Add-MEDIA_BUS_FMT_SENSOR_DATA-media-bus-f.patch b/target/linux/bcm27xx/patches-5.10/950-0211-media-uapi-Add-MEDIA_BUS_FMT_SENSOR_DATA-media-bus-f.patch new file mode 100644 index 0000000000..cc55451353 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0211-media-uapi-Add-MEDIA_BUS_FMT_SENSOR_DATA-media-bus-f.patch @@ -0,0 +1,64 @@ +From 6c8bd941bfcbb6fc4f6b4f8261aa03f280e80f20 Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Tue, 21 Jan 2020 14:06:47 +0000 +Subject: [PATCH] media: uapi: Add MEDIA_BUS_FMT_SENSOR_DATA media bus + format + +This patch adds MEDIA_BUS_FMT_SENSOR_DATA used by the bcm2835-unicam +driver to support CSI-2 embedded data streams from camera sensors. + +Signed-off-by: Naushir Patuck +--- + .../media/v4l/subdev-formats.rst | 33 +++++++++++++++++++ + include/uapi/linux/media-bus-format.h | 3 ++ + 2 files changed, 36 insertions(+) + +--- a/Documentation/userspace-api/media/v4l/subdev-formats.rst ++++ b/Documentation/userspace-api/media/v4l/subdev-formats.rst +@@ -7899,3 +7899,36 @@ formats. + - 0x5001 + - Interleaved raw UYVY and JPEG image format with embedded meta-data + used by Samsung S3C73MX camera sensors. ++ ++ ++ ++.. _v4l2-mbus-sensor-data: ++ ++Sensor Ancillary Metadata Formats ++^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ ++ ++This section lists ancillary data generated by a camera sensor and ++transmitted over a stream on the camera bus. ++ ++The following table lists the existing sensor ancillary metadata formats: ++ ++ ++.. _v4l2-mbus-pixelcode-sensor-metadata: ++ ++.. tabularcolumns:: |p{8.0cm}|p{1.4cm}|p{7.7cm}| ++ ++.. flat-table:: Sensor ancillary metadata formats ++ :header-rows: 1 ++ :stub-columns: 0 ++ ++ * - Identifier ++ - Code ++ - Comments ++ * .. _MEDIA_BUS_FMT_SENSOR_DATA: ++ ++ - MEDIA_BUS_FMT_SENSOR_DATA ++ - 0x7001 ++ - Sensor vendor specific ancillary metadata. Some vendors follow a generic ++ CSI-2/SMIA embedded data format as described in the `CSI-2 specification. ++ `_ ++ +--- a/include/uapi/linux/media-bus-format.h ++++ b/include/uapi/linux/media-bus-format.h +@@ -156,4 +156,7 @@ + /* HSV - next is 0x6002 */ + #define MEDIA_BUS_FMT_AHSV8888_1X32 0x6001 + ++/* Sensor ancillary metadata formats - next is 0x7002 */ ++#define MEDIA_BUS_FMT_SENSOR_DATA 0x7001 ++ + #endif /* __LINUX_MEDIA_BUS_FORMAT_H */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0212-media-bcm2835-unicam-Add-support-for-mulitple-device.patch b/target/linux/bcm27xx/patches-5.10/950-0212-media-bcm2835-unicam-Add-support-for-mulitple-device.patch new file mode 100644 index 0000000000..3c21c3b523 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0212-media-bcm2835-unicam-Add-support-for-mulitple-device.patch @@ -0,0 +1,1084 @@ +From bc7cac66c7c590d64fb4d4597f3bb661f7a0893f Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Tue, 7 Apr 2020 10:42:14 +0100 +Subject: [PATCH] media: bcm2835-unicam: Add support for mulitple + device nodes. + +Move device node specific state out of the device state structure and +into a new node structure. This separation will be needed for future +changes where we will add an embedded data node to the driver to work +alongside the existing image data node. + +Currently only use a single image node, so this commit does not add +any functional changes. + +Signed-off-by: Naushir Patuck +--- + .../media/platform/bcm2835/bcm2835-unicam.c | 484 ++++++++++-------- + 1 file changed, 283 insertions(+), 201 deletions(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -109,7 +109,8 @@ MODULE_PARM_DESC(debug, "Debug level 0-3 + /* Define a nominal minimum image size */ + #define MIN_WIDTH 16 + #define MIN_HEIGHT 16 +- ++/* Maximum number of simulataneous streams Uncaim can handle. */ ++#define MAX_NODES 2 + /* + * struct unicam_fmt - Unicam media bus format information + * @pixelformat: V4L2 pixel format FCC identifier. 0 if n/a. +@@ -346,11 +347,37 @@ struct unicam_cfg { + + #define MAX_POSSIBLE_PIX_FMTS (ARRAY_SIZE(formats)) + +-struct unicam_device { +- /* V4l2 specific parameters */ ++struct unicam_node { ++ bool registered; ++ unsigned int pad_id; ++ /* Pointer pointing to current v4l2_buffer */ ++ struct unicam_buffer *cur_frm; ++ /* Pointer pointing to next v4l2_buffer */ ++ struct unicam_buffer *next_frm; ++ /* video capture */ ++ const struct unicam_fmt *fmt; ++ /* Used to store current pixel format */ ++ struct v4l2_format v_fmt; ++ /* Used to store current mbus frame format */ ++ struct v4l2_mbus_framefmt m_fmt; ++ /* Buffer queue used in video-buf */ ++ struct vb2_queue buffer_queue; ++ /* Queue of filled frames */ ++ struct unicam_dmaqueue dma_queue; ++ /* IRQ lock for DMA queue */ ++ spinlock_t dma_queue_lock; ++ /* lock used to access this structure */ ++ struct mutex lock; + /* Identifies video device for this channel */ + struct video_device video_dev; ++ /* Pointer to the parent handle */ ++ struct unicam_device *dev; ++ struct media_pad pad; + struct v4l2_ctrl_handler ctrl_handler; ++}; ++ ++struct unicam_device { ++ /* V4l2 specific parameters */ + + struct v4l2_fwnode_endpoint endpoint; + +@@ -363,7 +390,6 @@ struct unicam_device { + /* V4l2 device */ + struct v4l2_device v4l2_dev; + struct media_device mdev; +- struct media_pad pad; + + /* parent device */ + struct platform_device *pdev; +@@ -378,18 +404,6 @@ struct unicam_device { + /* current input at the sub device */ + int current_input; + +- /* Pointer pointing to current v4l2_buffer */ +- struct unicam_buffer *cur_frm; +- /* Pointer pointing to next v4l2_buffer */ +- struct unicam_buffer *next_frm; +- +- /* video capture */ +- const struct unicam_fmt *fmt; +- /* Used to store current pixel format */ +- struct v4l2_format v_fmt; +- /* Used to store current mbus frame format */ +- struct v4l2_mbus_framefmt m_fmt; +- + unsigned int virtual_channel; + enum v4l2_mbus_type bus_type; + /* +@@ -401,20 +415,10 @@ struct unicam_device { + unsigned int active_data_lanes; + + struct v4l2_rect crop; +- +- /* Currently selected input on subdev */ +- int input; +- +- /* Buffer queue used in video-buf */ +- struct vb2_queue buffer_queue; +- /* Queue of filled frames */ +- struct unicam_dmaqueue dma_queue; +- /* IRQ lock for DMA queue */ +- spinlock_t dma_queue_lock; +- /* lock used to access this structure */ +- struct mutex lock; + /* Flag to denote that we are processing buffers */ + int streaming; ++ ++ struct unicam_node node[MAX_NODES]; + }; + + /* Hardware access */ +@@ -526,10 +530,11 @@ static inline unsigned int bytes_per_lin + } + + static int __subdev_get_format(struct unicam_device *dev, +- struct v4l2_mbus_framefmt *fmt) ++ struct v4l2_mbus_framefmt *fmt, int pad_id) + { + struct v4l2_subdev_format sd_fmt = { + .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ .pad = pad_id + }; + int ret; + +@@ -598,29 +603,30 @@ static int unicam_calc_format_size_bpl(s + return 0; + } + +-static int unicam_reset_format(struct unicam_device *dev) ++static int unicam_reset_format(struct unicam_node *node) + { ++ struct unicam_device *dev = node->dev; + struct v4l2_mbus_framefmt mbus_fmt; + int ret; + +- ret = __subdev_get_format(dev, &mbus_fmt); ++ ret = __subdev_get_format(dev, &mbus_fmt, node->pad_id); + if (ret) { + unicam_err(dev, "Failed to get_format - ret %d\n", ret); + return ret; + } + +- if (mbus_fmt.code != dev->fmt->code) { ++ if (mbus_fmt.code != dev->node[0].fmt->code) { + unicam_err(dev, "code mismatch - fmt->code %08x, mbus_fmt.code %08x\n", +- dev->fmt->code, mbus_fmt.code); ++ dev->node[0].fmt->code, mbus_fmt.code); + return ret; + } + +- v4l2_fill_pix_format(&dev->v_fmt.fmt.pix, &mbus_fmt); +- dev->v_fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE; ++ v4l2_fill_pix_format(&dev->node[0].v_fmt.fmt.pix, &mbus_fmt); ++ dev->node[0].v_fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE; + +- unicam_calc_format_size_bpl(dev, dev->fmt, &dev->v_fmt); ++ unicam_calc_format_size_bpl(dev, dev->node[0].fmt, &dev->node[0].v_fmt); + +- dev->m_fmt = mbus_fmt; ++ dev->node[0].m_fmt = mbus_fmt; + + return 0; + } +@@ -635,14 +641,14 @@ static void unicam_wr_dma_addr(struct un + + reg_write(&dev->cfg, UNICAM_IBSA0, dmaaddr); + reg_write(&dev->cfg, UNICAM_IBEA0, +- dmaaddr + dev->v_fmt.fmt.pix.sizeimage); ++ dmaaddr + dev->node[0].v_fmt.fmt.pix.sizeimage); + } + + static inline unsigned int unicam_get_lines_done(struct unicam_device *dev) + { + dma_addr_t start_addr, cur_addr; +- unsigned int stride = dev->v_fmt.fmt.pix.bytesperline; +- struct unicam_buffer *frm = dev->cur_frm; ++ unsigned int stride = dev->node[0].v_fmt.fmt.pix.bytesperline; ++ struct unicam_buffer *frm = dev->node[0].cur_frm; + + if (!frm) + return 0; +@@ -654,12 +660,12 @@ static inline unsigned int unicam_get_li + + static inline void unicam_schedule_next_buffer(struct unicam_device *dev) + { +- struct unicam_dmaqueue *dma_q = &dev->dma_queue; ++ struct unicam_dmaqueue *dma_q = &dev->node[0].dma_queue; + struct unicam_buffer *buf; + dma_addr_t addr; + + buf = list_entry(dma_q->active.next, struct unicam_buffer, list); +- dev->next_frm = buf; ++ dev->node[0].next_frm = buf; + list_del(&buf->list); + + addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0); +@@ -668,11 +674,11 @@ static inline void unicam_schedule_next_ + + static inline void unicam_process_buffer_complete(struct unicam_device *dev) + { +- dev->cur_frm->vb.field = dev->m_fmt.field; +- dev->cur_frm->vb.sequence = dev->sequence++; ++ dev->node[0].cur_frm->vb.field = dev->node[0].m_fmt.field; ++ dev->node[0].cur_frm->vb.sequence = dev->sequence++; + +- vb2_buffer_done(&dev->cur_frm->vb.vb2_buf, VB2_BUF_STATE_DONE); +- dev->cur_frm = dev->next_frm; ++ vb2_buffer_done(&dev->node[0].cur_frm->vb.vb2_buf, VB2_BUF_STATE_DONE); ++ dev->node[0].cur_frm = dev->node[0].next_frm; + } + + /* +@@ -687,7 +693,7 @@ static irqreturn_t unicam_isr(int irq, v + { + struct unicam_device *unicam = (struct unicam_device *)dev; + struct unicam_cfg *cfg = &unicam->cfg; +- struct unicam_dmaqueue *dma_q = &unicam->dma_queue; ++ struct unicam_dmaqueue *dma_q = &unicam->node[0].dma_queue; + unsigned int lines_done = unicam_get_lines_done(dev); + unsigned int sequence = unicam->sequence; + int ista, sta; +@@ -720,8 +726,9 @@ static irqreturn_t unicam_isr(int irq, v + * Timestamp is to be when the first data byte was captured, + * aka frame start. + */ +- if (unicam->cur_frm) +- unicam->cur_frm->vb.vb2_buf.timestamp = ktime_get_ns(); ++ if (unicam->node[0].cur_frm) ++ unicam->node[0].cur_frm->vb.vb2_buf.timestamp = ++ ktime_get_ns(); + } + if (ista & UNICAM_FEI || sta & UNICAM_PI0) { + /* +@@ -729,7 +736,8 @@ static irqreturn_t unicam_isr(int irq, v + * stop the peripheral. Overwrite the frame we've just + * captured instead. + */ +- if (unicam->cur_frm && unicam->cur_frm != unicam->next_frm) ++ if (unicam->node[0].cur_frm && ++ unicam->node[0].cur_frm != unicam->node[0].next_frm) + unicam_process_buffer_complete(unicam); + } + +@@ -738,11 +746,11 @@ static irqreturn_t unicam_isr(int irq, v + * already started. + */ + if (ista & (UNICAM_FSI | UNICAM_LCI) && !(ista & UNICAM_FEI)) { +- spin_lock(&unicam->dma_queue_lock); ++ spin_lock(&unicam->node[0].dma_queue_lock); + if (!list_empty(&dma_q->active) && +- unicam->cur_frm == unicam->next_frm) ++ unicam->node[0].cur_frm == unicam->node[0].next_frm) + unicam_schedule_next_buffer(unicam); +- spin_unlock(&unicam->dma_queue_lock); ++ spin_unlock(&unicam->node[0].dma_queue_lock); + } + + if (reg_read(&unicam->cfg, UNICAM_ICTL) & UNICAM_FCM) { +@@ -756,7 +764,8 @@ static irqreturn_t unicam_isr(int irq, v + static int unicam_querycap(struct file *file, void *priv, + struct v4l2_capability *cap) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + + strlcpy(cap->driver, UNICAM_MODULE_NAME, sizeof(cap->driver)); + strlcpy(cap->card, UNICAM_MODULE_NAME, sizeof(cap->card)); +@@ -770,7 +779,8 @@ static int unicam_querycap(struct file * + static int unicam_enum_fmt_vid_cap(struct file *file, void *priv, + struct v4l2_fmtdesc *f) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + struct v4l2_subdev_mbus_code_enum mbus_code; + const struct unicam_fmt *fmt = NULL; + int index = 0; +@@ -815,9 +825,9 @@ static int unicam_enum_fmt_vid_cap(struc + static int unicam_g_fmt_vid_cap(struct file *file, void *priv, + struct v4l2_format *f) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); + +- *f = dev->v_fmt; ++ *f = node->v_fmt; + + return 0; + } +@@ -859,9 +869,11 @@ const struct unicam_fmt *get_first_suppo + static int unicam_try_fmt_vid_cap(struct file *file, void *priv, + struct v4l2_format *f) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + struct v4l2_subdev_format sd_fmt = { + .which = V4L2_SUBDEV_FORMAT_TRY, ++ .pad = 0 + }; + struct v4l2_mbus_framefmt *mbus_fmt = &sd_fmt.format; + const struct unicam_fmt *fmt; +@@ -939,8 +951,9 @@ static int unicam_try_fmt_vid_cap(struct + static int unicam_s_fmt_vid_cap(struct file *file, void *priv, + struct v4l2_format *f) + { +- struct unicam_device *dev = video_drvdata(file); +- struct vb2_queue *q = &dev->buffer_queue; ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ struct vb2_queue *q = &node->buffer_queue; + struct v4l2_mbus_framefmt mbus_fmt = {0}; + const struct unicam_fmt *fmt; + int ret; +@@ -985,17 +998,18 @@ static int unicam_s_fmt_vid_cap(struct f + return -EINVAL; + } + +- dev->fmt = fmt; +- dev->v_fmt.fmt.pix.pixelformat = f->fmt.pix.pixelformat; +- dev->v_fmt.fmt.pix.bytesperline = f->fmt.pix.bytesperline; +- unicam_reset_format(dev); +- +- unicam_dbg(3, dev, "%s %dx%d, mbus_fmt 0x%08X, V4L2 pix 0x%08X.\n", +- __func__, dev->v_fmt.fmt.pix.width, +- dev->v_fmt.fmt.pix.height, mbus_fmt.code, +- dev->v_fmt.fmt.pix.pixelformat); ++ node->fmt = fmt; ++ node->v_fmt.fmt.pix.pixelformat = f->fmt.pix.pixelformat; ++ node->v_fmt.fmt.pix.bytesperline = f->fmt.pix.bytesperline; ++ unicam_reset_format(node); ++ ++ unicam_dbg(3, dev, ++ "%s %dx%d, mbus_fmt 0x%08X, V4L2 pix 0x%08X.\n", ++ __func__, node->v_fmt.fmt.pix.width, ++ node->v_fmt.fmt.pix.height, mbus_fmt.code, ++ node->v_fmt.fmt.pix.pixelformat); + +- *f = dev->v_fmt; ++ *f = node->v_fmt; + + return 0; + } +@@ -1006,8 +1020,9 @@ static int unicam_queue_setup(struct vb2 + unsigned int sizes[], + struct device *alloc_devs[]) + { +- struct unicam_device *dev = vb2_get_drv_priv(vq); +- unsigned int size = dev->v_fmt.fmt.pix.sizeimage; ++ struct unicam_node *node = vb2_get_drv_priv(vq); ++ struct unicam_device *dev = node->dev; ++ unsigned int size = node->v_fmt.fmt.pix.sizeimage; + + if (vq->num_buffers + *nbuffers < 3) + *nbuffers = 3 - vq->num_buffers; +@@ -1029,15 +1044,16 @@ static int unicam_queue_setup(struct vb2 + + static int unicam_buffer_prepare(struct vb2_buffer *vb) + { +- struct unicam_device *dev = vb2_get_drv_priv(vb->vb2_queue); ++ struct unicam_node *node = vb2_get_drv_priv(vb->vb2_queue); ++ struct unicam_device *dev = node->dev; + struct unicam_buffer *buf = container_of(vb, struct unicam_buffer, + vb.vb2_buf); + unsigned long size; + +- if (WARN_ON(!dev->fmt)) ++ if (WARN_ON(!node->fmt)) + return -EINVAL; + +- size = dev->v_fmt.fmt.pix.sizeimage; ++ size = node->v_fmt.fmt.pix.sizeimage; + if (vb2_plane_size(vb, 0) < size) { + unicam_err(dev, "data will not fit into plane (%lu < %lu)\n", + vb2_plane_size(vb, 0), size); +@@ -1050,15 +1066,15 @@ static int unicam_buffer_prepare(struct + + static void unicam_buffer_queue(struct vb2_buffer *vb) + { +- struct unicam_device *dev = vb2_get_drv_priv(vb->vb2_queue); ++ struct unicam_node *node = vb2_get_drv_priv(vb->vb2_queue); + struct unicam_buffer *buf = container_of(vb, struct unicam_buffer, + vb.vb2_buf); +- struct unicam_dmaqueue *dma_queue = &dev->dma_queue; ++ struct unicam_dmaqueue *dma_queue = &node->dma_queue; + unsigned long flags = 0; + +- spin_lock_irqsave(&dev->dma_queue_lock, flags); ++ spin_lock_irqsave(&node->dma_queue_lock, flags); + list_add_tail(&buf->list, &dma_queue->active); +- spin_unlock_irqrestore(&dev->dma_queue_lock, flags); ++ spin_unlock_irqrestore(&node->dma_queue_lock, flags); + } + + static void unicam_set_packing_config(struct unicam_device *dev) +@@ -1066,11 +1082,12 @@ static void unicam_set_packing_config(st + int pack, unpack; + u32 val; + +- if (dev->v_fmt.fmt.pix.pixelformat == dev->fmt->fourcc) { ++ if (dev->node[0].v_fmt.fmt.pix.pixelformat == ++ dev->node[0].fmt->fourcc) { + unpack = UNICAM_PUM_NONE; + pack = UNICAM_PPM_NONE; + } else { +- switch (dev->fmt->depth) { ++ switch (dev->node[0].fmt->depth) { + case 8: + unpack = UNICAM_PUM_UNPACK8; + break; +@@ -1108,17 +1125,17 @@ static void unicam_cfg_image_id(struct u + if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { + /* CSI2 mode */ + reg_write(cfg, UNICAM_IDI0, +- (dev->virtual_channel << 6) | dev->fmt->csi_dt); ++ (dev->virtual_channel << 6) | dev->node[0].fmt->csi_dt); + } else { + /* CCP2 mode */ +- reg_write(cfg, UNICAM_IDI0, (0x80 | dev->fmt->csi_dt)); ++ reg_write(cfg, UNICAM_IDI0, (0x80 | dev->node[0].fmt->csi_dt)); + } + } + + static void unicam_start_rx(struct unicam_device *dev, unsigned long addr) + { + struct unicam_cfg *cfg = &dev->cfg; +- int line_int_freq = dev->v_fmt.fmt.pix.height >> 2; ++ int line_int_freq = dev->node[0].v_fmt.fmt.pix.height >> 2; + unsigned int i; + u32 val; + +@@ -1266,7 +1283,8 @@ static void unicam_start_rx(struct unica + reg_write(cfg, UNICAM_DAT3, val); + } + +- reg_write(&dev->cfg, UNICAM_IBLS, dev->v_fmt.fmt.pix.bytesperline); ++ reg_write(&dev->cfg, UNICAM_IBLS, ++ dev->node[0].v_fmt.fmt.pix.bytesperline); + unicam_wr_dma_addr(dev, addr); + unicam_set_packing_config(dev); + unicam_cfg_image_id(dev); +@@ -1327,21 +1345,22 @@ static void unicam_disable(struct unicam + + static int unicam_start_streaming(struct vb2_queue *vq, unsigned int count) + { +- struct unicam_device *dev = vb2_get_drv_priv(vq); +- struct unicam_dmaqueue *dma_q = &dev->dma_queue; ++ struct unicam_node *node = vb2_get_drv_priv(vq); ++ struct unicam_device *dev = node->dev; ++ struct unicam_dmaqueue *dma_q = &node->dma_queue; + struct unicam_buffer *buf, *tmp; + unsigned long addr = 0; + unsigned long flags; + int ret; + +- spin_lock_irqsave(&dev->dma_queue_lock, flags); ++ spin_lock_irqsave(&node->dma_queue_lock, flags); + buf = list_entry(dma_q->active.next, struct unicam_buffer, list); +- dev->cur_frm = buf; +- dev->next_frm = buf; ++ node->cur_frm = buf; ++ node->next_frm = buf; + list_del(&buf->list); +- spin_unlock_irqrestore(&dev->dma_queue_lock, flags); ++ spin_unlock_irqrestore(&node->dma_queue_lock, flags); + +- addr = vb2_dma_contig_plane_dma_addr(&dev->cur_frm->vb.vb2_buf, 0); ++ addr = vb2_dma_contig_plane_dma_addr(&node->cur_frm->vb.vb2_buf, 0); + dev->sequence = 0; + + ret = unicam_runtime_get(dev); +@@ -1411,20 +1430,21 @@ err_release_buffers: + list_del(&buf->list); + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); + } +- if (dev->cur_frm != dev->next_frm) +- vb2_buffer_done(&dev->next_frm->vb.vb2_buf, ++ if (node->cur_frm != node->next_frm) ++ vb2_buffer_done(&node->next_frm->vb.vb2_buf, + VB2_BUF_STATE_QUEUED); +- vb2_buffer_done(&dev->cur_frm->vb.vb2_buf, VB2_BUF_STATE_QUEUED); +- dev->next_frm = NULL; +- dev->cur_frm = NULL; ++ vb2_buffer_done(&node->cur_frm->vb.vb2_buf, VB2_BUF_STATE_QUEUED); ++ node->next_frm = NULL; ++ node->cur_frm = NULL; + + return ret; + } + + static void unicam_stop_streaming(struct vb2_queue *vq) + { +- struct unicam_device *dev = vb2_get_drv_priv(vq); +- struct unicam_dmaqueue *dma_q = &dev->dma_queue; ++ struct unicam_node *node = vb2_get_drv_priv(vq); ++ struct unicam_device *dev = node->dev; ++ struct unicam_dmaqueue *dma_q = &node->dma_queue; + struct unicam_buffer *buf, *tmp; + unsigned long flags; + +@@ -1434,22 +1454,24 @@ static void unicam_stop_streaming(struct + unicam_disable(dev); + + /* Release all active buffers */ +- spin_lock_irqsave(&dev->dma_queue_lock, flags); ++ spin_lock_irqsave(&node->dma_queue_lock, flags); + list_for_each_entry_safe(buf, tmp, &dma_q->active, list) { + list_del(&buf->list); + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); + } + +- if (dev->cur_frm == dev->next_frm) { +- vb2_buffer_done(&dev->cur_frm->vb.vb2_buf, VB2_BUF_STATE_ERROR); ++ if (node->cur_frm == node->next_frm) { ++ vb2_buffer_done(&node->cur_frm->vb.vb2_buf, ++ VB2_BUF_STATE_ERROR); + } else { +- vb2_buffer_done(&dev->cur_frm->vb.vb2_buf, VB2_BUF_STATE_ERROR); +- vb2_buffer_done(&dev->next_frm->vb.vb2_buf, ++ vb2_buffer_done(&node->cur_frm->vb.vb2_buf, ++ VB2_BUF_STATE_ERROR); ++ vb2_buffer_done(&node->next_frm->vb.vb2_buf, + VB2_BUF_STATE_ERROR); + } +- dev->cur_frm = NULL; +- dev->next_frm = NULL; +- spin_unlock_irqrestore(&dev->dma_queue_lock, flags); ++ node->cur_frm = NULL; ++ node->next_frm = NULL; ++ spin_unlock_irqrestore(&node->dma_queue_lock, flags); + + clk_disable_unprepare(dev->clock); + unicam_runtime_put(dev); +@@ -1458,7 +1480,8 @@ static void unicam_stop_streaming(struct + static int unicam_enum_input(struct file *file, void *priv, + struct v4l2_input *inp) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + + if (inp->index != 0) + return -EINVAL; +@@ -1506,21 +1529,24 @@ static int unicam_s_input(struct file *f + static int unicam_querystd(struct file *file, void *priv, + v4l2_std_id *std) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + + return v4l2_subdev_call(dev->sensor, video, querystd, std); + } + + static int unicam_g_std(struct file *file, void *priv, v4l2_std_id *std) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + + return v4l2_subdev_call(dev->sensor, video, g_std, std); + } + + static int unicam_s_std(struct file *file, void *priv, v4l2_std_id std) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + int ret; + v4l2_std_id current_std; + +@@ -1531,29 +1557,31 @@ static int unicam_s_std(struct file *fil + if (std == current_std) + return 0; + +- if (vb2_is_busy(&dev->buffer_queue)) ++ if (vb2_is_busy(&node->buffer_queue)) + return -EBUSY; + + ret = v4l2_subdev_call(dev->sensor, video, s_std, std); + + /* Force recomputation of bytesperline */ +- dev->v_fmt.fmt.pix.bytesperline = 0; ++ node->v_fmt.fmt.pix.bytesperline = 0; + +- unicam_reset_format(dev); ++ unicam_reset_format(node); + + return ret; + } + + static int unicam_s_edid(struct file *file, void *priv, struct v4l2_edid *edid) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + + return v4l2_subdev_call(dev->sensor, pad, set_edid, edid); + } + + static int unicam_g_edid(struct file *file, void *priv, struct v4l2_edid *edid) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + + return v4l2_subdev_call(dev->sensor, pad, get_edid, edid); + } +@@ -1561,7 +1589,8 @@ static int unicam_g_edid(struct file *fi + static int unicam_enum_framesizes(struct file *file, void *priv, + struct v4l2_frmsizeenum *fsize) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + const struct unicam_fmt *fmt; + struct v4l2_subdev_frame_size_enum fse; + int ret; +@@ -1596,7 +1625,8 @@ static int unicam_enum_framesizes(struct + static int unicam_enum_frameintervals(struct file *file, void *priv, + struct v4l2_frmivalenum *fival) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + const struct unicam_fmt *fmt; + struct v4l2_subdev_frame_interval_enum fie = { + .index = fival->index, +@@ -1624,14 +1654,16 @@ static int unicam_enum_frameintervals(st + + static int unicam_g_parm(struct file *file, void *fh, struct v4l2_streamparm *a) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + + return v4l2_g_parm_cap(video_devdata(file), dev->sensor, a); + } + + static int unicam_s_parm(struct file *file, void *fh, struct v4l2_streamparm *a) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + + return v4l2_s_parm_cap(video_devdata(file), dev->sensor, a); + } +@@ -1639,7 +1671,8 @@ static int unicam_s_parm(struct file *fi + static int unicam_g_dv_timings(struct file *file, void *priv, + struct v4l2_dv_timings *timings) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + + return v4l2_subdev_call(dev->sensor, video, g_dv_timings, timings); + } +@@ -1647,7 +1680,8 @@ static int unicam_g_dv_timings(struct fi + static int unicam_s_dv_timings(struct file *file, void *priv, + struct v4l2_dv_timings *timings) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + struct v4l2_dv_timings current_timings; + int ret; + +@@ -1657,15 +1691,15 @@ static int unicam_s_dv_timings(struct fi + if (v4l2_match_dv_timings(timings, ¤t_timings, 0, false)) + return 0; + +- if (vb2_is_busy(&dev->buffer_queue)) ++ if (vb2_is_busy(&node->buffer_queue)) + return -EBUSY; + + ret = v4l2_subdev_call(dev->sensor, video, s_dv_timings, timings); + + /* Force recomputation of bytesperline */ +- dev->v_fmt.fmt.pix.bytesperline = 0; ++ node->v_fmt.fmt.pix.bytesperline = 0; + +- unicam_reset_format(dev); ++ unicam_reset_format(node); + + return ret; + } +@@ -1673,7 +1707,8 @@ static int unicam_s_dv_timings(struct fi + static int unicam_query_dv_timings(struct file *file, void *priv, + struct v4l2_dv_timings *timings) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + + return v4l2_subdev_call(dev->sensor, video, query_dv_timings, timings); + } +@@ -1681,7 +1716,8 @@ static int unicam_query_dv_timings(struc + static int unicam_enum_dv_timings(struct file *file, void *priv, + struct v4l2_enum_dv_timings *timings) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + + return v4l2_subdev_call(dev->sensor, pad, enum_dv_timings, timings); + } +@@ -1689,7 +1725,8 @@ static int unicam_enum_dv_timings(struct + static int unicam_dv_timings_cap(struct file *file, void *priv, + struct v4l2_dv_timings_cap *cap) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + + return v4l2_subdev_call(dev->sensor, pad, dv_timings_cap, cap); + } +@@ -1707,7 +1744,8 @@ static int unicam_subscribe_event(struct + + static int unicam_log_status(struct file *file, void *fh) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + struct unicam_cfg *cfg = &dev->cfg; + u32 reg; + +@@ -1716,10 +1754,10 @@ static int unicam_log_status(struct file + + unicam_info(dev, "-----Receiver status-----\n"); + unicam_info(dev, "V4L2 width/height: %ux%u\n", +- dev->v_fmt.fmt.pix.width, dev->v_fmt.fmt.pix.height); +- unicam_info(dev, "Mediabus format: %08x\n", dev->fmt->code); ++ node->v_fmt.fmt.pix.width, node->v_fmt.fmt.pix.height); ++ unicam_info(dev, "Mediabus format: %08x\n", node->fmt->code); + unicam_info(dev, "V4L2 format: %08x\n", +- dev->v_fmt.fmt.pix.pixelformat); ++ node->v_fmt.fmt.pix.pixelformat); + reg = reg_read(&dev->cfg, UNICAM_IPIPE); + unicam_info(dev, "Unpacking/packing: %u / %u\n", + get_field(reg, UNICAM_PUM_MASK), +@@ -1744,7 +1782,7 @@ static void unicam_notify(struct v4l2_su + + switch (notification) { + case V4L2_DEVICE_NOTIFY_EVENT: +- v4l2_event_queue(&dev->video_dev, arg); ++ v4l2_event_queue(&dev->node[0].video_dev, arg); + break; + default: + break; +@@ -1767,10 +1805,11 @@ static const struct vb2_ops unicam_video + */ + static int unicam_open(struct file *file) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + int ret; + +- mutex_lock(&dev->lock); ++ mutex_lock(&node->lock); + + ret = v4l2_fh_open(file); + if (ret) { +@@ -1790,18 +1829,19 @@ static int unicam_open(struct file *file + ret = 0; + + unlock: +- mutex_unlock(&dev->lock); ++ mutex_unlock(&node->lock); + return ret; + } + + static int unicam_release(struct file *file) + { +- struct unicam_device *dev = video_drvdata(file); ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; + struct v4l2_subdev *sd = dev->sensor; + bool fh_singular; + int ret; + +- mutex_lock(&dev->lock); ++ mutex_lock(&node->lock); + + fh_singular = v4l2_fh_is_singular_file(file); + +@@ -1810,7 +1850,7 @@ static int unicam_release(struct file *f + if (fh_singular) + v4l2_subdev_call(sd, core, s_power, 0); + +- mutex_unlock(&dev->lock); ++ mutex_unlock(&node->lock); + + return ret; + } +@@ -1892,7 +1932,8 @@ unicam_async_bound(struct v4l2_async_not + return 0; + } + +-static int unicam_probe_complete(struct unicam_device *unicam) ++static int register_node(struct unicam_device *unicam, struct unicam_node *node, ++ enum v4l2_buf_type type, int pad_id) + { + struct video_device *vdev; + struct vb2_queue *q; +@@ -1900,15 +1941,7 @@ static int unicam_probe_complete(struct + const struct unicam_fmt *fmt; + int ret; + +- v4l2_set_subdev_hostdata(unicam->sensor, unicam); +- +- unicam->v4l2_dev.notify = unicam_notify; +- +- unicam->sensor_config = v4l2_subdev_alloc_pad_config(unicam->sensor); +- if (!unicam->sensor_config) +- return -ENOMEM; +- +- ret = __subdev_get_format(unicam, &mbus_fmt); ++ ret = __subdev_get_format(unicam, &mbus_fmt, pad_id); + if (ret) { + unicam_err(unicam, "Failed to get_format - ret %d\n", ret); + return ret; +@@ -1938,14 +1971,15 @@ static int unicam_probe_complete(struct + return -EINVAL; + } + +- unicam->fmt = fmt; ++ node->pad_id = pad_id; ++ node->fmt = fmt; + if (fmt->fourcc) +- unicam->v_fmt.fmt.pix.pixelformat = fmt->fourcc; ++ node->v_fmt.fmt.pix.pixelformat = fmt->fourcc; + else +- unicam->v_fmt.fmt.pix.pixelformat = fmt->repacked_fourcc; ++ node->v_fmt.fmt.pix.pixelformat = fmt->repacked_fourcc; + + /* Read current subdev format */ +- unicam_reset_format(unicam); ++ unicam_reset_format(node); + + if (v4l2_subdev_has_op(unicam->sensor, video, s_std)) { + v4l2_std_id tvnorms; +@@ -1962,27 +1996,30 @@ static int unicam_probe_complete(struct + g_tvnorms, &tvnorms); + if (WARN_ON(ret)) + return -EINVAL; +- unicam->video_dev.tvnorms |= tvnorms; ++ node->video_dev.tvnorms |= tvnorms; + } + +- spin_lock_init(&unicam->dma_queue_lock); +- mutex_init(&unicam->lock); ++ spin_lock_init(&node->dma_queue_lock); ++ mutex_init(&node->lock); + +- /* Add controls from the subdevice */ +- ret = v4l2_ctrl_add_handler(&unicam->ctrl_handler, +- unicam->sensor->ctrl_handler, NULL, true); +- if (ret < 0) +- return ret; ++ if (type == V4L2_BUF_TYPE_VIDEO_CAPTURE) { ++ /* Add controls from the subdevice */ ++ ret = v4l2_ctrl_add_handler(&node->ctrl_handler, ++ unicam->sensor->ctrl_handler, NULL, ++ true); ++ if (ret < 0) ++ return ret; ++ } + +- q = &unicam->buffer_queue; +- q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; ++ q = &node->buffer_queue; ++ q->type = type; + q->io_modes = VB2_MMAP | VB2_DMABUF | VB2_READ; +- q->drv_priv = unicam; ++ q->drv_priv = node; + q->ops = &unicam_video_qops; + q->mem_ops = &vb2_dma_contig_memops; + q->buf_struct_size = sizeof(struct unicam_buffer); + q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC; +- q->lock = &unicam->lock; ++ q->lock = &node->lock; + q->min_buffers_needed = 2; + q->dev = &unicam->pdev->dev; + +@@ -1992,9 +2029,9 @@ static int unicam_probe_complete(struct + return ret; + } + +- INIT_LIST_HEAD(&unicam->dma_queue.active); ++ INIT_LIST_HEAD(&node->dma_queue.active); + +- vdev = &unicam->video_dev; ++ vdev = &node->video_dev; + strlcpy(vdev->name, UNICAM_MODULE_NAME, sizeof(vdev->name)); + vdev->release = video_device_release_empty; + vdev->fops = &unicam_fops; +@@ -2002,69 +2039,113 @@ static int unicam_probe_complete(struct + vdev->v4l2_dev = &unicam->v4l2_dev; + vdev->vfl_dir = VFL_DIR_RX; + vdev->queue = q; +- vdev->lock = &unicam->lock; ++ vdev->lock = &node->lock; + vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING | + V4L2_CAP_READWRITE; +- + /* If the source has no controls then remove our ctrl handler. */ +- if (list_empty(&unicam->ctrl_handler.ctrls)) ++ if (list_empty(&node->ctrl_handler.ctrls)) + unicam->v4l2_dev.ctrl_handler = NULL; + +- video_set_drvdata(vdev, unicam); ++ node->dev = unicam; ++ video_set_drvdata(vdev, node); + vdev->entity.flags |= MEDIA_ENT_FL_DEFAULT; + + if (!v4l2_subdev_has_op(unicam->sensor, video, s_std)) { +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_S_STD); +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_G_STD); +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_ENUMSTD); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_STD); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_STD); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_ENUMSTD); + } + if (!v4l2_subdev_has_op(unicam->sensor, video, querystd)) +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_QUERYSTD); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_QUERYSTD); + if (!v4l2_subdev_has_op(unicam->sensor, video, s_dv_timings)) { +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_S_EDID); +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_G_EDID); +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_DV_TIMINGS_CAP); +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_G_DV_TIMINGS); +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_S_DV_TIMINGS); +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_ENUM_DV_TIMINGS); +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_QUERY_DV_TIMINGS); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_EDID); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_EDID); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_DV_TIMINGS_CAP); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_DV_TIMINGS); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_DV_TIMINGS); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_ENUM_DV_TIMINGS); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_QUERY_DV_TIMINGS); + } + if (!v4l2_subdev_has_op(unicam->sensor, pad, enum_frame_interval)) +- v4l2_disable_ioctl(&unicam->video_dev, ++ v4l2_disable_ioctl(&node->video_dev, + VIDIOC_ENUM_FRAMEINTERVALS); + if (!v4l2_subdev_has_op(unicam->sensor, video, g_frame_interval)) +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_G_PARM); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_PARM); + if (!v4l2_subdev_has_op(unicam->sensor, video, s_frame_interval)) +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_S_PARM); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_PARM); + + if (!v4l2_subdev_has_op(unicam->sensor, pad, enum_frame_size)) +- v4l2_disable_ioctl(&unicam->video_dev, VIDIOC_ENUM_FRAMESIZES); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_ENUM_FRAMESIZES); + + ret = video_register_device(vdev, VFL_TYPE_VIDEO, -1); + if (ret) { + unicam_err(unicam, "Unable to register video device.\n"); + return ret; + } ++ node->registered = true; + +- ret = v4l2_device_register_ro_subdev_nodes(&unicam->v4l2_dev); ++ ret = media_create_pad_link(&unicam->sensor->entity, ++ 0, &node->video_dev.entity, 0, ++ MEDIA_LNK_FL_ENABLED | ++ MEDIA_LNK_FL_IMMUTABLE); ++ if (ret) ++ unicam_err(unicam, "Unable to create pad links.\n"); ++ ++ return ret; ++} ++ ++static void unregister_nodes(struct unicam_device *unicam) ++{ ++ if (unicam->node[0].registered) { ++ video_unregister_device(&unicam->node[0].video_dev); ++ unicam->node[0].registered = false; ++ } ++ if (unicam->node[1].registered) { ++ video_unregister_device(&unicam->node[1].video_dev); ++ unicam->node[1].registered = false; ++ } ++} ++ ++static int unicam_probe_complete(struct unicam_device *unicam) ++{ ++ int ret; ++ ++ v4l2_set_subdev_hostdata(unicam->sensor, unicam); ++ ++ unicam->v4l2_dev.notify = unicam_notify; ++ ++ unicam->sensor_config = v4l2_subdev_alloc_pad_config(unicam->sensor); ++ if (!unicam->sensor_config) ++ return -ENOMEM; ++ ++ ret = register_node(unicam, &unicam->node[0], ++ V4L2_BUF_TYPE_VIDEO_CAPTURE, 0); + if (ret) { +- unicam_err(unicam, +- "Unable to register subdev nodes.\n"); +- video_unregister_device(&unicam->video_dev); +- return ret; ++ unicam_err(unicam, "Unable to register subdev node 0.\n"); ++ goto unregister; ++ } ++ if (unicam->sensor->entity.num_pads >= 2) { ++ ret = register_node(unicam, &unicam->node[1], ++ V4L2_BUF_TYPE_META_CAPTURE, 1); ++ if (ret) { ++ unicam_err(unicam, ++ "Unable to register subdev node 1.\n"); ++ goto unregister; ++ } + } + +- ret = media_create_pad_link(&unicam->sensor->entity, 0, +- &unicam->video_dev.entity, 0, +- MEDIA_LNK_FL_ENABLED | +- MEDIA_LNK_FL_IMMUTABLE); ++ ret = v4l2_device_register_ro_subdev_nodes(&unicam->v4l2_dev); + if (ret) { +- unicam_err(unicam, "Unable to create pad links.\n"); +- video_unregister_device(&unicam->video_dev); +- return ret; ++ unicam_err(unicam, "Unable to register subdev nodes.\n"); ++ goto unregister; + } + + return 0; ++ ++unregister: ++ unregister_nodes(unicam); ++ ++ return ret; + } + + static int unicam_async_complete(struct v4l2_async_notifier *notifier) +@@ -2274,7 +2355,8 @@ static int unicam_probe(struct platform_ + pdev->dev.driver->name, dev_name(&pdev->dev)); + unicam->mdev.hw_revision = 1; + +- media_entity_pads_init(&unicam->video_dev.entity, 1, &unicam->pad); ++ media_entity_pads_init(&unicam->node[0].video_dev.entity, 1, ++ &unicam->node[0].pad); + media_device_init(&unicam->mdev); + + unicam->v4l2_dev.mdev = &unicam->mdev; +@@ -2294,7 +2376,7 @@ static int unicam_probe(struct platform_ + } + + /* Reserve space for the controls */ +- hdl = &unicam->ctrl_handler; ++ hdl = &unicam->node[0].ctrl_handler; + ret = v4l2_ctrl_handler_init(hdl, 16); + if (ret < 0) + goto media_unregister; +@@ -2335,9 +2417,9 @@ static int unicam_remove(struct platform + pm_runtime_disable(&pdev->dev); + + v4l2_async_notifier_unregister(&unicam->notifier); +- v4l2_ctrl_handler_free(&unicam->ctrl_handler); ++ v4l2_ctrl_handler_free(&unicam->node[0].ctrl_handler); + v4l2_device_unregister(&unicam->v4l2_dev); +- video_unregister_device(&unicam->video_dev); ++ unregister_nodes(unicam); + if (unicam->sensor_config) + v4l2_subdev_free_pad_config(unicam->sensor_config); + media_device_unregister(&unicam->mdev); diff --git a/target/linux/bcm27xx/patches-5.10/950-0213-media-bcm2835-unicam-Add-embedded-data-node.patch b/target/linux/bcm27xx/patches-5.10/950-0213-media-bcm2835-unicam-Add-embedded-data-node.patch new file mode 100644 index 0000000000..4fc8270869 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0213-media-bcm2835-unicam-Add-embedded-data-node.patch @@ -0,0 +1,1170 @@ +From 0dae2f81f08fc6f8641e10b99c61e73314553d79 Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Thu, 16 Apr 2020 11:35:41 +0100 +Subject: [PATCH] media: bcm2835-unicam: Add embedded data node. + +This patch adds a new node in the bcm2835-unicam driver to support +CSI-2 embedded data streams. The subdevice is queried to see if +embedded data is available from the sensor. + +Signed-off-by: Naushir Patuck +--- + .../media/platform/bcm2835/bcm2835-unicam.c | 667 +++++++++++++----- + 1 file changed, 474 insertions(+), 193 deletions(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -109,8 +109,15 @@ MODULE_PARM_DESC(debug, "Debug level 0-3 + /* Define a nominal minimum image size */ + #define MIN_WIDTH 16 + #define MIN_HEIGHT 16 +-/* Maximum number of simulataneous streams Uncaim can handle. */ +-#define MAX_NODES 2 ++/* Default size of the embedded buffer */ ++#define UNICAM_EMBEDDED_SIZE 8192 ++ ++enum pad_types { ++ IMAGE_PAD, ++ METADATA_PAD, ++ MAX_NODES ++}; ++ + /* + * struct unicam_fmt - Unicam media bus format information + * @pixelformat: V4L2 pixel format FCC identifier. 0 if n/a. +@@ -327,6 +334,12 @@ static const struct unicam_fmt formats[] + .depth = 12, + .csi_dt = 0x2c, + }, ++ /* Embedded data format */ ++ { ++ .fourcc = V4L2_META_FMT_SENSOR_DATA, ++ .code = MEDIA_BUS_FMT_SENSOR_DATA, ++ .depth = 8, ++ } + }; + + struct unicam_dmaqueue { +@@ -348,7 +361,9 @@ struct unicam_cfg { + #define MAX_POSSIBLE_PIX_FMTS (ARRAY_SIZE(formats)) + + struct unicam_node { +- bool registered; ++ int registered; ++ int open; ++ int streaming; + unsigned int pad_id; + /* Pointer pointing to current v4l2_buffer */ + struct unicam_buffer *cur_frm; +@@ -374,6 +389,7 @@ struct unicam_node { + struct unicam_device *dev; + struct media_pad pad; + struct v4l2_ctrl_handler ctrl_handler; ++ unsigned int embedded_lines; + }; + + struct unicam_device { +@@ -401,8 +417,6 @@ struct unicam_device { + struct v4l2_subdev *sensor; + /* Pad config for the sensor */ + struct v4l2_subdev_pad_config *sensor_config; +- /* current input at the sub device */ +- int current_input; + + unsigned int virtual_channel; + enum v4l2_mbus_type bus_type; +@@ -413,10 +427,7 @@ struct unicam_device { + unsigned int bus_flags; + unsigned int max_data_lanes; + unsigned int active_data_lanes; +- +- struct v4l2_rect crop; +- /* Flag to denote that we are processing buffers */ +- int streaming; ++ bool sensor_embedded_data; + + struct unicam_node node[MAX_NODES]; + }; +@@ -488,6 +499,7 @@ static int check_mbus_format(struct unic + for (i = 0; !ret && i < MAX_ENUM_MBUS_CODE; i++) { + memset(&mbus_code, 0, sizeof(mbus_code)); + mbus_code.index = i; ++ mbus_code.pad = IMAGE_PAD; + mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE; + + ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, +@@ -552,10 +564,11 @@ static int __subdev_get_format(struct un + } + + static int __subdev_set_format(struct unicam_device *dev, +- struct v4l2_mbus_framefmt *fmt) ++ struct v4l2_mbus_framefmt *fmt, int pad_id) + { + struct v4l2_subdev_format sd_fmt = { + .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ .pad = pad_id + }; + int ret; + +@@ -566,8 +579,12 @@ static int __subdev_set_format(struct un + if (ret < 0) + return ret; + +- unicam_dbg(1, dev, "%s %dx%d code:%04x\n", __func__, +- fmt->width, fmt->height, fmt->code); ++ if (pad_id == IMAGE_PAD) ++ unicam_dbg(1, dev, "%s %dx%d code:%04x\n", __func__, fmt->width, ++ fmt->height, fmt->code); ++ else ++ unicam_dbg(1, dev, "%s Embedded data code:%04x\n", __func__, ++ sd_fmt.format.code); + + return 0; + } +@@ -609,46 +626,70 @@ static int unicam_reset_format(struct un + struct v4l2_mbus_framefmt mbus_fmt; + int ret; + +- ret = __subdev_get_format(dev, &mbus_fmt, node->pad_id); +- if (ret) { +- unicam_err(dev, "Failed to get_format - ret %d\n", ret); +- return ret; +- } ++ if (dev->sensor_embedded_data || node->pad_id != METADATA_PAD) { ++ ret = __subdev_get_format(dev, &mbus_fmt, node->pad_id); ++ if (ret) { ++ unicam_err(dev, "Failed to get_format - ret %d\n", ret); ++ return ret; ++ } + +- if (mbus_fmt.code != dev->node[0].fmt->code) { +- unicam_err(dev, "code mismatch - fmt->code %08x, mbus_fmt.code %08x\n", +- dev->node[0].fmt->code, mbus_fmt.code); +- return ret; ++ if (mbus_fmt.code != node->fmt->code) { ++ unicam_err(dev, "code mismatch - fmt->code %08x, mbus_fmt.code %08x\n", ++ node->fmt->code, mbus_fmt.code); ++ return ret; ++ } + } + +- v4l2_fill_pix_format(&dev->node[0].v_fmt.fmt.pix, &mbus_fmt); +- dev->node[0].v_fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE; +- +- unicam_calc_format_size_bpl(dev, dev->node[0].fmt, &dev->node[0].v_fmt); +- +- dev->node[0].m_fmt = mbus_fmt; ++ if (node->pad_id == IMAGE_PAD) { ++ v4l2_fill_pix_format(&node->v_fmt.fmt.pix, &mbus_fmt); ++ node->v_fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE; ++ unicam_calc_format_size_bpl(dev, node->fmt, &node->v_fmt); ++ } else { ++ node->v_fmt.type = V4L2_BUF_TYPE_META_CAPTURE; ++ node->v_fmt.fmt.meta.dataformat = V4L2_META_FMT_SENSOR_DATA; ++ if (dev->sensor_embedded_data) { ++ node->v_fmt.fmt.meta.buffersize = ++ mbus_fmt.width * mbus_fmt.height; ++ node->embedded_lines = mbus_fmt.height; ++ } else { ++ node->v_fmt.fmt.meta.buffersize = UNICAM_EMBEDDED_SIZE; ++ node->embedded_lines = 1; ++ } ++ } + ++ node->m_fmt = mbus_fmt; + return 0; + } + +-static void unicam_wr_dma_addr(struct unicam_device *dev, dma_addr_t dmaaddr) ++static void unicam_wr_dma_addr(struct unicam_device *dev, dma_addr_t dmaaddr, ++ int pad_id) + { ++ dma_addr_t endaddr; ++ + /* + * dmaaddr should be a 32-bit address with the top two bits set to 0x3 + * to signify uncached access through the Videocore memory controller. + */ + BUG_ON((dmaaddr >> 30) != 0x3); + +- reg_write(&dev->cfg, UNICAM_IBSA0, dmaaddr); +- reg_write(&dev->cfg, UNICAM_IBEA0, +- dmaaddr + dev->node[0].v_fmt.fmt.pix.sizeimage); ++ if (pad_id == IMAGE_PAD) { ++ endaddr = dmaaddr + ++ dev->node[IMAGE_PAD].v_fmt.fmt.pix.sizeimage; ++ reg_write(&dev->cfg, UNICAM_IBSA0, dmaaddr); ++ reg_write(&dev->cfg, UNICAM_IBEA0, endaddr); ++ } else { ++ endaddr = dmaaddr + ++ dev->node[METADATA_PAD].v_fmt.fmt.meta.buffersize; ++ reg_write(&dev->cfg, UNICAM_DBSA0, dmaaddr); ++ reg_write(&dev->cfg, UNICAM_DBEA0, endaddr); ++ } + } + + static inline unsigned int unicam_get_lines_done(struct unicam_device *dev) + { + dma_addr_t start_addr, cur_addr; +- unsigned int stride = dev->node[0].v_fmt.fmt.pix.bytesperline; +- struct unicam_buffer *frm = dev->node[0].cur_frm; ++ unsigned int stride = dev->node[IMAGE_PAD].v_fmt.fmt.pix.bytesperline; ++ struct unicam_buffer *frm = dev->node[IMAGE_PAD].cur_frm; + + if (!frm) + return 0; +@@ -658,27 +699,51 @@ static inline unsigned int unicam_get_li + return (unsigned int)(cur_addr - start_addr) / stride; + } + +-static inline void unicam_schedule_next_buffer(struct unicam_device *dev) ++static inline void unicam_schedule_next_buffer(struct unicam_node *node) + { +- struct unicam_dmaqueue *dma_q = &dev->node[0].dma_queue; ++ struct unicam_device *dev = node->dev; ++ struct unicam_dmaqueue *dma_q = &node->dma_queue; + struct unicam_buffer *buf; + dma_addr_t addr; + + buf = list_entry(dma_q->active.next, struct unicam_buffer, list); +- dev->node[0].next_frm = buf; ++ node->next_frm = buf; + list_del(&buf->list); + + addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0); +- unicam_wr_dma_addr(dev, addr); ++ unicam_wr_dma_addr(dev, addr, node->pad_id); + } + +-static inline void unicam_process_buffer_complete(struct unicam_device *dev) ++static inline void unicam_process_buffer_complete(struct unicam_node *node, ++ unsigned int sequence) + { +- dev->node[0].cur_frm->vb.field = dev->node[0].m_fmt.field; +- dev->node[0].cur_frm->vb.sequence = dev->sequence++; ++ node->cur_frm->vb.field = node->m_fmt.field; ++ node->cur_frm->vb.sequence = sequence; ++ ++ vb2_buffer_done(&node->cur_frm->vb.vb2_buf, VB2_BUF_STATE_DONE); ++ node->cur_frm = node->next_frm; ++} + +- vb2_buffer_done(&dev->node[0].cur_frm->vb.vb2_buf, VB2_BUF_STATE_DONE); +- dev->node[0].cur_frm = dev->node[0].next_frm; ++static int unicam_num_nodes_streaming(struct unicam_device *dev) ++{ ++ return dev->node[IMAGE_PAD].streaming + ++ dev->node[METADATA_PAD].streaming; ++} ++ ++static int unicam_all_nodes_streaming(struct unicam_device *dev) ++{ ++ int ret; ++ ++ ret = dev->node[IMAGE_PAD].open && dev->node[IMAGE_PAD].streaming; ++ ret &= !dev->node[METADATA_PAD].open || ++ dev->node[METADATA_PAD].streaming; ++ return ret; ++} ++ ++static int unicam_all_nodes_disabled(struct unicam_device *dev) ++{ ++ return !dev->node[IMAGE_PAD].streaming && ++ !dev->node[METADATA_PAD].streaming; + } + + /* +@@ -693,10 +758,12 @@ static irqreturn_t unicam_isr(int irq, v + { + struct unicam_device *unicam = (struct unicam_device *)dev; + struct unicam_cfg *cfg = &unicam->cfg; +- struct unicam_dmaqueue *dma_q = &unicam->node[0].dma_queue; + unsigned int lines_done = unicam_get_lines_done(dev); + unsigned int sequence = unicam->sequence; ++ int num_nodes_streaming = unicam_num_nodes_streaming(dev); + int ista, sta; ++ u64 ts; ++ int i; + + /* + * Don't service interrupts if not streaming. +@@ -704,7 +771,7 @@ static irqreturn_t unicam_isr(int irq, v + * peripheral without the kernel knowing (that + * shouldn't happen, but causes issues if it does). + */ +- if (!unicam->streaming) ++ if (unicam_all_nodes_disabled(unicam)) + return IRQ_HANDLED; + + sta = reg_read(cfg, UNICAM_STA); +@@ -726,9 +793,12 @@ static irqreturn_t unicam_isr(int irq, v + * Timestamp is to be when the first data byte was captured, + * aka frame start. + */ +- if (unicam->node[0].cur_frm) +- unicam->node[0].cur_frm->vb.vb2_buf.timestamp = +- ktime_get_ns(); ++ ts = ktime_get_ns(); ++ for (i = 0; i < num_nodes_streaming; i++) { ++ if (unicam->node[i].cur_frm) ++ unicam->node[i].cur_frm->vb.vb2_buf.timestamp = ++ ts; ++ } + } + if (ista & UNICAM_FEI || sta & UNICAM_PI0) { + /* +@@ -736,9 +806,13 @@ static irqreturn_t unicam_isr(int irq, v + * stop the peripheral. Overwrite the frame we've just + * captured instead. + */ +- if (unicam->node[0].cur_frm && +- unicam->node[0].cur_frm != unicam->node[0].next_frm) +- unicam_process_buffer_complete(unicam); ++ for (i = 0; i < num_nodes_streaming; i++) { ++ if (unicam->node[i].cur_frm && ++ unicam->node[i].cur_frm != unicam->node[i].next_frm) ++ unicam_process_buffer_complete(&unicam->node[i], ++ sequence); ++ } ++ unicam->sequence++; + } + + /* Cannot swap buffer at frame end, there may be a race condition +@@ -746,11 +820,13 @@ static irqreturn_t unicam_isr(int irq, v + * already started. + */ + if (ista & (UNICAM_FSI | UNICAM_LCI) && !(ista & UNICAM_FEI)) { +- spin_lock(&unicam->node[0].dma_queue_lock); +- if (!list_empty(&dma_q->active) && +- unicam->node[0].cur_frm == unicam->node[0].next_frm) +- unicam_schedule_next_buffer(unicam); +- spin_unlock(&unicam->node[0].dma_queue_lock); ++ for (i = 0; i < num_nodes_streaming; i++) { ++ spin_lock(&unicam->node[i].dma_queue_lock); ++ if (!list_empty(&unicam->node[i].dma_queue.active) && ++ unicam->node[i].cur_frm == unicam->node[i].next_frm) ++ unicam_schedule_next_buffer(&unicam->node[i]); ++ spin_unlock(&unicam->node[i].dma_queue_lock); ++ } + } + + if (reg_read(&unicam->cfg, UNICAM_ICTL) & UNICAM_FCM) { +@@ -773,6 +849,15 @@ static int unicam_querycap(struct file * + snprintf(cap->bus_info, sizeof(cap->bus_info), + "platform:%s", dev->v4l2_dev.name); + ++ cap->capabilities = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING | ++ V4L2_CAP_READWRITE | V4L2_CAP_DEVICE_CAPS | ++ V4L2_CAP_META_CAPTURE; ++ ++ if (node->pad_id == IMAGE_PAD) ++ cap->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING; ++ else ++ cap->device_caps = V4L2_CAP_META_CAPTURE | V4L2_CAP_STREAMING; ++ + return 0; + } + +@@ -787,9 +872,14 @@ static int unicam_enum_fmt_vid_cap(struc + int ret = 0; + int i; + ++ if (node->pad_id == METADATA_PAD) ++ return -EINVAL; ++ + for (i = 0; !ret && i < MAX_ENUM_MBUS_CODE; i++) { + memset(&mbus_code, 0, sizeof(mbus_code)); + mbus_code.index = i; ++ mbus_code.pad = IMAGE_PAD; ++ mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE; + + ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, + NULL, &mbus_code); +@@ -827,6 +917,9 @@ static int unicam_g_fmt_vid_cap(struct f + { + struct unicam_node *node = video_drvdata(file); + ++ if (node->pad_id == METADATA_PAD) ++ return -EINVAL; ++ + *f = node->v_fmt; + + return 0; +@@ -843,6 +936,9 @@ const struct unicam_fmt *get_first_suppo + for (j = 0; ret != -EINVAL && ret != -ENOIOCTLCMD; ++j) { + memset(&mbus_code, 0, sizeof(mbus_code)); + mbus_code.index = j; ++ mbus_code.pad = IMAGE_PAD; ++ mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE; ++ + ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, NULL, + &mbus_code); + if (ret < 0) { +@@ -873,12 +969,15 @@ static int unicam_try_fmt_vid_cap(struct + struct unicam_device *dev = node->dev; + struct v4l2_subdev_format sd_fmt = { + .which = V4L2_SUBDEV_FORMAT_TRY, +- .pad = 0 ++ .pad = IMAGE_PAD + }; + struct v4l2_mbus_framefmt *mbus_fmt = &sd_fmt.format; + const struct unicam_fmt *fmt; + int ret; + ++ if (node->pad_id == METADATA_PAD) ++ return -EINVAL; ++ + fmt = find_format_by_pix(dev, f->fmt.pix.pixelformat); + if (!fmt) { + /* Pixel format not supported by unicam. Choose the first +@@ -983,7 +1082,7 @@ static int unicam_s_fmt_vid_cap(struct f + + v4l2_fill_mbus_format(&mbus_fmt, &f->fmt.pix, fmt->code); + +- ret = __subdev_set_format(dev, &mbus_fmt); ++ ret = __subdev_set_format(dev, &mbus_fmt, node->pad_id); + if (ret) { + unicam_dbg(3, dev, "%s __subdev_set_format failed %d\n", + __func__, ret); +@@ -1014,6 +1113,106 @@ static int unicam_s_fmt_vid_cap(struct f + return 0; + } + ++static int unicam_enum_fmt_meta_cap(struct file *file, void *priv, ++ struct v4l2_fmtdesc *f) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ struct v4l2_subdev_mbus_code_enum mbus_code; ++ const struct unicam_fmt *fmt = NULL; ++ int ret = 0; ++ ++ if (node->pad_id != METADATA_PAD || f->index != 0) ++ return -EINVAL; ++ ++ if (dev->sensor_embedded_data) { ++ memset(&mbus_code, 0, sizeof(mbus_code)); ++ mbus_code.index = f->index; ++ mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE; ++ mbus_code.pad = METADATA_PAD; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, NULL, ++ &mbus_code); ++ if (ret < 0) { ++ unicam_dbg(2, dev, ++ "subdev->enum_mbus_code idx 0 returned %d - index invalid\n", ++ ret); ++ return -EINVAL; ++ } ++ } else { ++ mbus_code.code = MEDIA_BUS_FMT_SENSOR_DATA; ++ } ++ ++ fmt = find_format_by_code(mbus_code.code); ++ if (fmt) ++ f->pixelformat = fmt->fourcc; ++ ++ return 0; ++} ++ ++static int unicam_g_fmt_meta_cap(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ ++ if (node->pad_id != METADATA_PAD) ++ return -EINVAL; ++ ++ *f = node->v_fmt; ++ ++ return 0; ++} ++ ++static int unicam_try_fmt_meta_cap(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ ++ if (node->pad_id != METADATA_PAD) ++ return -EINVAL; ++ ++ *f = node->v_fmt; ++ ++ return 0; ++} ++ ++static int unicam_s_fmt_meta_cap(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ struct v4l2_mbus_framefmt mbus_fmt = { 0 }; ++ const struct unicam_fmt *fmt; ++ int ret; ++ ++ if (node->pad_id == IMAGE_PAD) ++ return -EINVAL; ++ ++ if (dev->sensor_embedded_data) { ++ fmt = find_format_by_pix(dev, f->fmt.meta.dataformat); ++ if (!fmt) { ++ unicam_err(dev, "unknown format: V4L2 pix 0x%08x\n", ++ f->fmt.meta.dataformat); ++ return -EINVAL; ++ } ++ mbus_fmt.code = fmt->code; ++ ret = __subdev_set_format(dev, &mbus_fmt, node->pad_id); ++ if (ret) { ++ unicam_dbg(3, dev, "%s __subdev_set_format failed %d\n", ++ __func__, ret); ++ return ret; ++ } ++ } ++ ++ *f = node->v_fmt; ++ ++ unicam_dbg(3, dev, "%s size %d, V4L2 pix 0x%08x\n", ++ __func__, node->v_fmt.fmt.meta.buffersize, ++ node->v_fmt.fmt.meta.dataformat); ++ ++ return 0; ++} ++ + static int unicam_queue_setup(struct vb2_queue *vq, + unsigned int *nbuffers, + unsigned int *nplanes, +@@ -1022,7 +1221,9 @@ static int unicam_queue_setup(struct vb2 + { + struct unicam_node *node = vb2_get_drv_priv(vq); + struct unicam_device *dev = node->dev; +- unsigned int size = node->v_fmt.fmt.pix.sizeimage; ++ unsigned int size = node->pad_id == IMAGE_PAD ? ++ node->v_fmt.fmt.pix.sizeimage : ++ node->v_fmt.fmt.meta.buffersize; + + if (vq->num_buffers + *nbuffers < 3) + *nbuffers = 3 - vq->num_buffers; +@@ -1053,7 +1254,8 @@ static int unicam_buffer_prepare(struct + if (WARN_ON(!node->fmt)) + return -EINVAL; + +- size = node->v_fmt.fmt.pix.sizeimage; ++ size = node->pad_id == IMAGE_PAD ? node->v_fmt.fmt.pix.sizeimage : ++ node->v_fmt.fmt.meta.buffersize; + if (vb2_plane_size(vb, 0) < size) { + unicam_err(dev, "data will not fit into plane (%lu < %lu)\n", + vb2_plane_size(vb, 0), size); +@@ -1082,12 +1284,12 @@ static void unicam_set_packing_config(st + int pack, unpack; + u32 val; + +- if (dev->node[0].v_fmt.fmt.pix.pixelformat == +- dev->node[0].fmt->fourcc) { ++ if (dev->node[IMAGE_PAD].v_fmt.fmt.pix.pixelformat == ++ dev->node[IMAGE_PAD].fmt->fourcc) { + unpack = UNICAM_PUM_NONE; + pack = UNICAM_PPM_NONE; + } else { +- switch (dev->node[0].fmt->depth) { ++ switch (dev->node[IMAGE_PAD].fmt->depth) { + case 8: + unpack = UNICAM_PUM_UNPACK8; + break; +@@ -1125,17 +1327,31 @@ static void unicam_cfg_image_id(struct u + if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { + /* CSI2 mode */ + reg_write(cfg, UNICAM_IDI0, +- (dev->virtual_channel << 6) | dev->node[0].fmt->csi_dt); ++ (dev->virtual_channel << 6) | ++ dev->node[IMAGE_PAD].fmt->csi_dt); + } else { + /* CCP2 mode */ +- reg_write(cfg, UNICAM_IDI0, (0x80 | dev->node[0].fmt->csi_dt)); ++ reg_write(cfg, UNICAM_IDI0, ++ 0x80 | dev->node[IMAGE_PAD].fmt->csi_dt); + } + } + +-static void unicam_start_rx(struct unicam_device *dev, unsigned long addr) ++static void unicam_enable_ed(struct unicam_device *dev) ++{ ++ struct unicam_cfg *cfg = &dev->cfg; ++ u32 val = reg_read(cfg, UNICAM_DCS); ++ ++ set_field(&val, 2, UNICAM_EDL_MASK); ++ /* Do not wrap at the end of the embedded data buffer */ ++ set_field(&val, 0, UNICAM_DBOB); ++ ++ reg_write(cfg, UNICAM_DCS, val); ++} ++ ++static void unicam_start_rx(struct unicam_device *dev, dma_addr_t *addr) + { + struct unicam_cfg *cfg = &dev->cfg; +- int line_int_freq = dev->node[0].v_fmt.fmt.pix.height >> 2; ++ int line_int_freq = dev->node[IMAGE_PAD].v_fmt.fmt.pix.height >> 2; + unsigned int i; + u32 val; + +@@ -1284,27 +1500,31 @@ static void unicam_start_rx(struct unica + } + + reg_write(&dev->cfg, UNICAM_IBLS, +- dev->node[0].v_fmt.fmt.pix.bytesperline); +- unicam_wr_dma_addr(dev, addr); ++ dev->node[IMAGE_PAD].v_fmt.fmt.pix.bytesperline); ++ unicam_wr_dma_addr(dev, addr[IMAGE_PAD], IMAGE_PAD); + unicam_set_packing_config(dev); + unicam_cfg_image_id(dev); + +- /* Disabled embedded data */ +- val = 0; +- set_field(&val, 0, UNICAM_EDL_MASK); +- reg_write(cfg, UNICAM_DCS, val); +- + val = reg_read(cfg, UNICAM_MISC); + set_field(&val, 1, UNICAM_FL0); + set_field(&val, 1, UNICAM_FL1); + reg_write(cfg, UNICAM_MISC, val); + ++ if (dev->node[METADATA_PAD].streaming && dev->sensor_embedded_data) { ++ unicam_enable_ed(dev); ++ unicam_wr_dma_addr(dev, addr[METADATA_PAD], METADATA_PAD); ++ } ++ + /* Enable peripheral */ + reg_write_field(cfg, UNICAM_CTRL, 1, UNICAM_CPE); + + /* Load image pointers */ + reg_write_field(cfg, UNICAM_ICTL, 1, UNICAM_LIP_MASK); + ++ /* Load embedded data buffer pointers if needed */ ++ if (dev->node[METADATA_PAD].streaming && dev->sensor_embedded_data) ++ reg_write_field(cfg, UNICAM_DCS, 1, UNICAM_LDP); ++ + /* + * Enable trigger only for the first frame to + * sync correctly to the FS from the source. +@@ -1339,6 +1559,9 @@ static void unicam_disable(struct unicam + /* Disable peripheral */ + reg_write_field(cfg, UNICAM_CTRL, 0, UNICAM_CPE); + ++ /* Clear ED setup */ ++ reg_write(cfg, UNICAM_DCS, 0); ++ + /* Disable all lane clocks */ + clk_write(cfg, 0); + } +@@ -1347,26 +1570,23 @@ static int unicam_start_streaming(struct + { + struct unicam_node *node = vb2_get_drv_priv(vq); + struct unicam_device *dev = node->dev; +- struct unicam_dmaqueue *dma_q = &node->dma_queue; +- struct unicam_buffer *buf, *tmp; +- unsigned long addr = 0; ++ struct unicam_buffer *buf; ++ dma_addr_t buffer_addr[MAX_NODES] = { 0 }; ++ int num_nodes_streaming; + unsigned long flags; +- int ret; ++ int ret, i; + +- spin_lock_irqsave(&node->dma_queue_lock, flags); +- buf = list_entry(dma_q->active.next, struct unicam_buffer, list); +- node->cur_frm = buf; +- node->next_frm = buf; +- list_del(&buf->list); +- spin_unlock_irqrestore(&node->dma_queue_lock, flags); ++ node->streaming = 1; ++ if (!unicam_all_nodes_streaming(dev)) { ++ unicam_dbg(3, dev, "Not all nodes are streaming yet."); ++ return 0; ++ } + +- addr = vb2_dma_contig_plane_dma_addr(&node->cur_frm->vb.vb2_buf, 0); + dev->sequence = 0; +- + ret = unicam_runtime_get(dev); + if (ret < 0) { + unicam_dbg(3, dev, "unicam_runtime_get failed\n"); +- goto err_release_buffers; ++ return ret; + } + + dev->active_data_lanes = dev->max_data_lanes; +@@ -1388,7 +1608,7 @@ static int unicam_start_streaming(struct + dev->active_data_lanes = dev->max_data_lanes; + } + if (dev->active_data_lanes > dev->max_data_lanes) { +- unicam_err(dev, "Device has requested %u data lanes, which is >%u configured in DT\n", ++ unicam_err(dev, "Device has requested %u data lanes, which is >%u configured in DT\n", + dev->active_data_lanes, dev->max_data_lanes); + ret = -EINVAL; + goto err_pm_put; +@@ -1408,9 +1628,22 @@ static int unicam_start_streaming(struct + unicam_err(dev, "Failed to enable CSI clock: %d\n", ret); + goto err_pm_put; + } +- dev->streaming = 1; + +- unicam_start_rx(dev, addr); ++ num_nodes_streaming = unicam_num_nodes_streaming(dev); ++ for (i = 0; i < num_nodes_streaming; i++) { ++ spin_lock_irqsave(&dev->node[i].dma_queue_lock, flags); ++ buf = list_entry(dev->node[i].dma_queue.active.next, ++ struct unicam_buffer, list); ++ dev->node[i].cur_frm = buf; ++ dev->node[i].next_frm = buf; ++ list_del(&buf->list); ++ spin_unlock_irqrestore(&dev->node[i].dma_queue_lock, flags); ++ buffer_addr[i] = ++ vb2_dma_contig_plane_dma_addr(&dev->node[i].cur_frm->vb.vb2_buf, ++ 0); ++ } ++ ++ unicam_start_rx(dev, buffer_addr); + + ret = v4l2_subdev_call(dev->sensor, video, s_stream, 1); + if (ret < 0) { +@@ -1421,21 +1654,11 @@ static int unicam_start_streaming(struct + return 0; + + err_disable_unicam: ++ node->streaming = 0; + unicam_disable(dev); + clk_disable_unprepare(dev->clock); + err_pm_put: + unicam_runtime_put(dev); +-err_release_buffers: +- list_for_each_entry_safe(buf, tmp, &dma_q->active, list) { +- list_del(&buf->list); +- vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); +- } +- if (node->cur_frm != node->next_frm) +- vb2_buffer_done(&node->next_frm->vb.vb2_buf, +- VB2_BUF_STATE_QUEUED); +- vb2_buffer_done(&node->cur_frm->vb.vb2_buf, VB2_BUF_STATE_QUEUED); +- node->next_frm = NULL; +- node->cur_frm = NULL; + + return ret; + } +@@ -1448,33 +1671,47 @@ static void unicam_stop_streaming(struct + struct unicam_buffer *buf, *tmp; + unsigned long flags; + +- if (v4l2_subdev_call(dev->sensor, video, s_stream, 0) < 0) +- unicam_err(dev, "stream off failed in subdev\n"); ++ node->streaming = 0; + +- unicam_disable(dev); ++ if (node->pad_id == IMAGE_PAD) { ++ /* Stop streaming the sensor and disable the peripheral. ++ * We cannot continue streaming embedded data with the ++ * image pad disabled. ++ */ ++ if (v4l2_subdev_call(dev->sensor, video, s_stream, 0) < 0) ++ unicam_err(dev, "stream off failed in subdev\n"); + +- /* Release all active buffers */ ++ unicam_disable(dev); ++ clk_disable_unprepare(dev->clock); ++ unicam_runtime_put(dev); ++ ++ } else if (node->pad_id == METADATA_PAD) { ++ /* Null out the embedded data buffer address so the HW does ++ * not use it. This is only really needed if the embedded data ++ * pad is disabled before the image pad. The 0x3 in the top two ++ * bits signifies uncached accesses through the Videocore ++ * memory controller. ++ */ ++ unicam_wr_dma_addr(dev, 0xc0000000, METADATA_PAD); ++ } ++ ++ /* Clear all queued buffers for the node */ + spin_lock_irqsave(&node->dma_queue_lock, flags); + list_for_each_entry_safe(buf, tmp, &dma_q->active, list) { + list_del(&buf->list); + vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); + } + +- if (node->cur_frm == node->next_frm) { +- vb2_buffer_done(&node->cur_frm->vb.vb2_buf, +- VB2_BUF_STATE_ERROR); +- } else { ++ if (node->cur_frm) + vb2_buffer_done(&node->cur_frm->vb.vb2_buf, + VB2_BUF_STATE_ERROR); ++ if (node->next_frm && node->cur_frm != node->next_frm) + vb2_buffer_done(&node->next_frm->vb.vb2_buf, + VB2_BUF_STATE_ERROR); +- } ++ + node->cur_frm = NULL; + node->next_frm = NULL; + spin_unlock_irqrestore(&node->dma_queue_lock, flags); +- +- clk_disable_unprepare(dev->clock); +- unicam_runtime_put(dev); + } + + static int unicam_enum_input(struct file *file, void *priv, +@@ -1595,17 +1832,23 @@ static int unicam_enum_framesizes(struct + struct v4l2_subdev_frame_size_enum fse; + int ret; + +- /* check for valid format */ +- fmt = find_format_by_pix(dev, fsize->pixel_format); +- if (!fmt) { +- unicam_dbg(3, dev, "Invalid pixel code: %x\n", +- fsize->pixel_format); +- return -EINVAL; ++ if (node->pad_id == IMAGE_PAD) { ++ /* check for valid format */ ++ fmt = find_format_by_pix(dev, fsize->pixel_format); ++ if (!fmt) { ++ unicam_dbg(3, dev, "Invalid pixel code: %x\n", ++ fsize->pixel_format); ++ return -EINVAL; ++ } ++ fse.code = fmt->code; ++ } else { ++ /* This pad is for embedded data, so just set the format */ ++ fse.code = MEDIA_BUS_FMT_SENSOR_DATA; + } + ++ fse.which = V4L2_SUBDEV_FORMAT_ACTIVE; + fse.index = fsize->index; +- fse.pad = 0; +- fse.code = fmt->code; ++ fse.pad = node->pad_id; + + ret = v4l2_subdev_call(dev->sensor, pad, enum_frame_size, NULL, &fse); + if (ret) +@@ -1782,7 +2025,7 @@ static void unicam_notify(struct v4l2_su + + switch (notification) { + case V4L2_DEVICE_NOTIFY_EVENT: +- v4l2_event_queue(&dev->node[0].video_dev, arg); ++ v4l2_event_queue(&dev->node[IMAGE_PAD].video_dev, arg); + break; + default: + break; +@@ -1826,6 +2069,7 @@ static int unicam_open(struct file *file + goto unlock; + } + ++ node->open++; + ret = 0; + + unlock: +@@ -1850,6 +2094,10 @@ static int unicam_release(struct file *f + if (fh_singular) + v4l2_subdev_call(sd, core, s_power, 0); + ++ if (node->streaming) ++ unicam_stop_streaming(&node->buffer_queue); ++ ++ node->open--; + mutex_unlock(&node->lock); + + return ret; +@@ -1874,6 +2122,11 @@ static const struct v4l2_ioctl_ops unica + .vidioc_s_fmt_vid_cap = unicam_s_fmt_vid_cap, + .vidioc_try_fmt_vid_cap = unicam_try_fmt_vid_cap, + ++ .vidioc_enum_fmt_meta_cap = unicam_enum_fmt_meta_cap, ++ .vidioc_g_fmt_meta_cap = unicam_g_fmt_meta_cap, ++ .vidioc_s_fmt_meta_cap = unicam_s_fmt_meta_cap, ++ .vidioc_try_fmt_meta_cap = unicam_try_fmt_meta_cap, ++ + .vidioc_enum_input = unicam_enum_input, + .vidioc_g_input = unicam_g_input, + .vidioc_s_input = unicam_s_input, +@@ -1941,42 +2194,53 @@ static int register_node(struct unicam_d + const struct unicam_fmt *fmt; + int ret; + +- ret = __subdev_get_format(unicam, &mbus_fmt, pad_id); +- if (ret) { +- unicam_err(unicam, "Failed to get_format - ret %d\n", ret); +- return ret; +- } +- +- fmt = find_format_by_code(mbus_fmt.code); +- if (!fmt) { +- /* Find the first format that the sensor and unicam both +- * support +- */ +- fmt = get_first_supported_format(unicam); ++ if (unicam->sensor_embedded_data || pad_id != METADATA_PAD) { ++ ret = __subdev_get_format(unicam, &mbus_fmt, pad_id); ++ if (ret) { ++ unicam_err(unicam, "Failed to get_format - ret %d\n", ++ ret); ++ return ret; ++ } + +- if (!fmt) +- /* No compatible formats */ +- return -EINVAL; ++ fmt = find_format_by_code(mbus_fmt.code); ++ if (!fmt) { ++ /* Find the first format that the sensor and unicam both ++ * support ++ */ ++ fmt = get_first_supported_format(unicam); + +- mbus_fmt.code = fmt->code; +- ret = __subdev_set_format(unicam, &mbus_fmt); +- if (ret) +- return -EINVAL; +- } +- if (mbus_fmt.field != V4L2_FIELD_NONE) { +- /* Interlaced not supported - disable it now. */ +- mbus_fmt.field = V4L2_FIELD_NONE; +- ret = __subdev_set_format(unicam, &mbus_fmt); +- if (ret) +- return -EINVAL; ++ if (!fmt) ++ /* No compatible formats */ ++ return -EINVAL; ++ ++ mbus_fmt.code = fmt->code; ++ ret = __subdev_set_format(unicam, &mbus_fmt, pad_id); ++ if (ret) ++ return -EINVAL; ++ } ++ if (mbus_fmt.field != V4L2_FIELD_NONE) { ++ /* Interlaced not supported - disable it now. */ ++ mbus_fmt.field = V4L2_FIELD_NONE; ++ ret = __subdev_set_format(unicam, &mbus_fmt, pad_id); ++ if (ret) ++ return -EINVAL; ++ } ++ } else { ++ /* Fix this node format as embedded data. */ ++ fmt = find_format_by_code(MEDIA_BUS_FMT_SENSOR_DATA); + } + ++ node->dev = unicam; + node->pad_id = pad_id; + node->fmt = fmt; +- if (fmt->fourcc) +- node->v_fmt.fmt.pix.pixelformat = fmt->fourcc; +- else ++ if (fmt->fourcc) { ++ if (fmt->fourcc != V4L2_META_FMT_SENSOR_DATA) ++ node->v_fmt.fmt.pix.pixelformat = fmt->fourcc; ++ else ++ node->v_fmt.fmt.meta.dataformat = fmt->fourcc; ++ } else { + node->v_fmt.fmt.pix.pixelformat = fmt->repacked_fourcc; ++ } + + /* Read current subdev format */ + unicam_reset_format(node); +@@ -2002,13 +2266,21 @@ static int register_node(struct unicam_d + spin_lock_init(&node->dma_queue_lock); + mutex_init(&node->lock); + +- if (type == V4L2_BUF_TYPE_VIDEO_CAPTURE) { ++ vdev = &node->video_dev; ++ if (pad_id == IMAGE_PAD) { + /* Add controls from the subdevice */ + ret = v4l2_ctrl_add_handler(&node->ctrl_handler, + unicam->sensor->ctrl_handler, NULL, + true); + if (ret < 0) + return ret; ++ ++ /* ++ * If the sensor subdevice has any controls, associate the node ++ * with the ctrl handler to allow access from userland. ++ */ ++ if (!list_empty(&node->ctrl_handler.ctrls)) ++ vdev->ctrl_handler = &node->ctrl_handler; + } + + q = &node->buffer_queue; +@@ -2031,8 +2303,6 @@ static int register_node(struct unicam_d + + INIT_LIST_HEAD(&node->dma_queue.active); + +- vdev = &node->video_dev; +- strlcpy(vdev->name, UNICAM_MODULE_NAME, sizeof(vdev->name)); + vdev->release = video_device_release_empty; + vdev->fops = &unicam_fops; + vdev->ioctl_ops = &unicam_ioctl_ops; +@@ -2040,24 +2310,28 @@ static int register_node(struct unicam_d + vdev->vfl_dir = VFL_DIR_RX; + vdev->queue = q; + vdev->lock = &node->lock; +- vdev->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING | +- V4L2_CAP_READWRITE; +- /* If the source has no controls then remove our ctrl handler. */ +- if (list_empty(&node->ctrl_handler.ctrls)) +- unicam->v4l2_dev.ctrl_handler = NULL; ++ vdev->device_caps = (pad_id == IMAGE_PAD) ? ++ (V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING) : ++ (V4L2_CAP_META_CAPTURE | V4L2_CAP_STREAMING); ++ ++ /* Define the device names */ ++ snprintf(vdev->name, sizeof(vdev->name), "%s-%s", UNICAM_MODULE_NAME, ++ node->pad_id == IMAGE_PAD ? "image" : "embedded"); + +- node->dev = unicam; + video_set_drvdata(vdev, node); + vdev->entity.flags |= MEDIA_ENT_FL_DEFAULT; + +- if (!v4l2_subdev_has_op(unicam->sensor, video, s_std)) { ++ if (node->pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, video, s_std)) { + v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_STD); + v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_STD); + v4l2_disable_ioctl(&node->video_dev, VIDIOC_ENUMSTD); + } +- if (!v4l2_subdev_has_op(unicam->sensor, video, querystd)) ++ if (node->pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, video, querystd)) + v4l2_disable_ioctl(&node->video_dev, VIDIOC_QUERYSTD); +- if (!v4l2_subdev_has_op(unicam->sensor, video, s_dv_timings)) { ++ if (node->pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, video, s_dv_timings)) { + v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_EDID); + v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_EDID); + v4l2_disable_ioctl(&node->video_dev, VIDIOC_DV_TIMINGS_CAP); +@@ -2066,15 +2340,19 @@ static int register_node(struct unicam_d + v4l2_disable_ioctl(&node->video_dev, VIDIOC_ENUM_DV_TIMINGS); + v4l2_disable_ioctl(&node->video_dev, VIDIOC_QUERY_DV_TIMINGS); + } +- if (!v4l2_subdev_has_op(unicam->sensor, pad, enum_frame_interval)) ++ if (node->pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, pad, enum_frame_interval)) + v4l2_disable_ioctl(&node->video_dev, + VIDIOC_ENUM_FRAMEINTERVALS); +- if (!v4l2_subdev_has_op(unicam->sensor, video, g_frame_interval)) ++ if (node->pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, video, g_frame_interval)) + v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_PARM); +- if (!v4l2_subdev_has_op(unicam->sensor, video, s_frame_interval)) ++ if (node->pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, video, s_frame_interval)) + v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_PARM); + +- if (!v4l2_subdev_has_op(unicam->sensor, pad, enum_frame_size)) ++ if (node->pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, pad, enum_frame_size)) + v4l2_disable_ioctl(&node->video_dev, VIDIOC_ENUM_FRAMESIZES); + + ret = video_register_device(vdev, VFL_TYPE_VIDEO, -1); +@@ -2082,27 +2360,29 @@ static int register_node(struct unicam_d + unicam_err(unicam, "Unable to register video device.\n"); + return ret; + } +- node->registered = true; ++ node->registered = 1; + +- ret = media_create_pad_link(&unicam->sensor->entity, +- 0, &node->video_dev.entity, 0, +- MEDIA_LNK_FL_ENABLED | +- MEDIA_LNK_FL_IMMUTABLE); +- if (ret) +- unicam_err(unicam, "Unable to create pad links.\n"); ++ if (unicam->sensor_embedded_data) { ++ ret = media_create_pad_link(&unicam->sensor->entity, pad_id, ++ &node->video_dev.entity, 0, ++ MEDIA_LNK_FL_ENABLED | ++ MEDIA_LNK_FL_IMMUTABLE); ++ if (ret) ++ unicam_err(unicam, "Unable to create pad links.\n"); ++ } + + return ret; + } + + static void unregister_nodes(struct unicam_device *unicam) + { +- if (unicam->node[0].registered) { +- video_unregister_device(&unicam->node[0].video_dev); +- unicam->node[0].registered = false; +- } +- if (unicam->node[1].registered) { +- video_unregister_device(&unicam->node[1].video_dev); +- unicam->node[1].registered = false; ++ if (unicam->node[IMAGE_PAD].registered) { ++ video_unregister_device(&unicam->node[IMAGE_PAD].video_dev); ++ unicam->node[IMAGE_PAD].registered = 0; ++ } ++ if (unicam->node[METADATA_PAD].registered) { ++ video_unregister_device(&unicam->node[METADATA_PAD].video_dev); ++ unicam->node[METADATA_PAD].registered = 0; + } + } + +@@ -2118,20 +2398,20 @@ static int unicam_probe_complete(struct + if (!unicam->sensor_config) + return -ENOMEM; + +- ret = register_node(unicam, &unicam->node[0], +- V4L2_BUF_TYPE_VIDEO_CAPTURE, 0); ++ unicam->sensor_embedded_data = (unicam->sensor->entity.num_pads >= 2); ++ ++ ret = register_node(unicam, &unicam->node[IMAGE_PAD], ++ V4L2_BUF_TYPE_VIDEO_CAPTURE, IMAGE_PAD); + if (ret) { + unicam_err(unicam, "Unable to register subdev node 0.\n"); + goto unregister; + } +- if (unicam->sensor->entity.num_pads >= 2) { +- ret = register_node(unicam, &unicam->node[1], +- V4L2_BUF_TYPE_META_CAPTURE, 1); +- if (ret) { +- unicam_err(unicam, +- "Unable to register subdev node 1.\n"); +- goto unregister; +- } ++ ++ ret = register_node(unicam, &unicam->node[METADATA_PAD], ++ V4L2_BUF_TYPE_META_CAPTURE, METADATA_PAD); ++ if (ret) { ++ unicam_err(unicam, "Unable to register subdev node 1.\n"); ++ goto unregister; + } + + ret = v4l2_device_register_ro_subdev_nodes(&unicam->v4l2_dev); +@@ -2355,8 +2635,10 @@ static int unicam_probe(struct platform_ + pdev->dev.driver->name, dev_name(&pdev->dev)); + unicam->mdev.hw_revision = 1; + +- media_entity_pads_init(&unicam->node[0].video_dev.entity, 1, +- &unicam->node[0].pad); ++ media_entity_pads_init(&unicam->node[IMAGE_PAD].video_dev.entity, 1, ++ &unicam->node[IMAGE_PAD].pad); ++ media_entity_pads_init(&unicam->node[METADATA_PAD].video_dev.entity, 1, ++ &unicam->node[METADATA_PAD].pad); + media_device_init(&unicam->mdev); + + unicam->v4l2_dev.mdev = &unicam->mdev; +@@ -2376,11 +2658,10 @@ static int unicam_probe(struct platform_ + } + + /* Reserve space for the controls */ +- hdl = &unicam->node[0].ctrl_handler; ++ hdl = &unicam->node[IMAGE_PAD].ctrl_handler; + ret = v4l2_ctrl_handler_init(hdl, 16); + if (ret < 0) + goto media_unregister; +- unicam->v4l2_dev.ctrl_handler = hdl; + + /* set the driver data in platform device */ + platform_set_drvdata(pdev, unicam); +@@ -2417,7 +2698,7 @@ static int unicam_remove(struct platform + pm_runtime_disable(&pdev->dev); + + v4l2_async_notifier_unregister(&unicam->notifier); +- v4l2_ctrl_handler_free(&unicam->node[0].ctrl_handler); ++ v4l2_ctrl_handler_free(&unicam->node[IMAGE_PAD].ctrl_handler); + v4l2_device_unregister(&unicam->v4l2_dev); + unregister_nodes(unicam); + if (unicam->sensor_config) diff --git a/target/linux/bcm27xx/patches-5.10/950-0214-media-bcm2835-unicam-Use-dummy-buffer-if-none-have-b.patch b/target/linux/bcm27xx/patches-5.10/950-0214-media-bcm2835-unicam-Use-dummy-buffer-if-none-have-b.patch new file mode 100644 index 0000000000..811fa9f08c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0214-media-bcm2835-unicam-Use-dummy-buffer-if-none-have-b.patch @@ -0,0 +1,308 @@ +From 43f17e232abec4960a2edd6f245d6e1e0058a858 Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Thu, 2 Apr 2020 16:08:51 +0100 +Subject: [PATCH] media: bcm2835-unicam: Use dummy buffer if none have + been queued + +If no buffer has been queued by a userland application, we use an +internal dummy buffer for the hardware to spin in. This will allow +the driver to release the existing userland buffer back to the +application for processing. + +Signed-off-by: Naushir Patuck +--- + .../media/platform/bcm2835/bcm2835-unicam.c | 160 ++++++++++++------ + 1 file changed, 110 insertions(+), 50 deletions(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -47,6 +47,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -112,6 +113,12 @@ MODULE_PARM_DESC(debug, "Debug level 0-3 + /* Default size of the embedded buffer */ + #define UNICAM_EMBEDDED_SIZE 8192 + ++/* ++ * Size of the dummy buffer. Can be any size really, but the DMA ++ * allocation works in units of page sizes. ++ */ ++#define DUMMY_BUF_SIZE (PAGE_SIZE) ++ + enum pad_types { + IMAGE_PAD, + METADATA_PAD, +@@ -390,6 +397,12 @@ struct unicam_node { + struct media_pad pad; + struct v4l2_ctrl_handler ctrl_handler; + unsigned int embedded_lines; ++ /* ++ * Dummy buffer intended to be used by unicam ++ * if we have no other queued buffers to swap to. ++ */ ++ void *dummy_buf_cpu_addr; ++ dma_addr_t dummy_buf_dma_addr; + }; + + struct unicam_device { +@@ -661,27 +674,24 @@ static int unicam_reset_format(struct un + return 0; + } + +-static void unicam_wr_dma_addr(struct unicam_device *dev, dma_addr_t dmaaddr, +- int pad_id) ++static void unicam_wr_dma_addr(struct unicam_cfg *cfg, dma_addr_t dmaaddr, ++ unsigned int buffer_size, int pad_id) + { +- dma_addr_t endaddr; ++ dma_addr_t endaddr = dmaaddr + buffer_size; + + /* +- * dmaaddr should be a 32-bit address with the top two bits set to 0x3 +- * to signify uncached access through the Videocore memory controller. ++ * dmaaddr and endaddr should be a 32-bit address with the top two bits ++ * set to 0x3 to signify uncached access through the Videocore memory ++ * controller. + */ +- BUG_ON((dmaaddr >> 30) != 0x3); ++ BUG_ON((dmaaddr >> 30) != 0x3 && (endaddr >> 30) != 0x3); + + if (pad_id == IMAGE_PAD) { +- endaddr = dmaaddr + +- dev->node[IMAGE_PAD].v_fmt.fmt.pix.sizeimage; +- reg_write(&dev->cfg, UNICAM_IBSA0, dmaaddr); +- reg_write(&dev->cfg, UNICAM_IBEA0, endaddr); ++ reg_write(cfg, UNICAM_IBSA0, dmaaddr); ++ reg_write(cfg, UNICAM_IBEA0, endaddr); + } else { +- endaddr = dmaaddr + +- dev->node[METADATA_PAD].v_fmt.fmt.meta.buffersize; +- reg_write(&dev->cfg, UNICAM_DBSA0, dmaaddr); +- reg_write(&dev->cfg, UNICAM_DBEA0, endaddr); ++ reg_write(cfg, UNICAM_DBSA0, dmaaddr); ++ reg_write(cfg, UNICAM_DBEA0, endaddr); + } + } + +@@ -704,6 +714,7 @@ static inline void unicam_schedule_next_ + struct unicam_device *dev = node->dev; + struct unicam_dmaqueue *dma_q = &node->dma_queue; + struct unicam_buffer *buf; ++ unsigned int size; + dma_addr_t addr; + + buf = list_entry(dma_q->active.next, struct unicam_buffer, list); +@@ -711,7 +722,23 @@ static inline void unicam_schedule_next_ + list_del(&buf->list); + + addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0); +- unicam_wr_dma_addr(dev, addr, node->pad_id); ++ size = (node->pad_id == IMAGE_PAD) ? ++ dev->node[IMAGE_PAD].v_fmt.fmt.pix.sizeimage : ++ dev->node[METADATA_PAD].v_fmt.fmt.meta.buffersize; ++ ++ unicam_wr_dma_addr(&dev->cfg, addr, size, node->pad_id); ++} ++ ++static inline void unicam_schedule_dummy_buffer(struct unicam_node *node) ++{ ++ struct unicam_device *dev = node->dev; ++ dma_addr_t addr = node->dummy_buf_dma_addr; ++ ++ unicam_dbg(3, dev, "Scheduling dummy buffer for node %d\n", ++ node->pad_id); ++ ++ unicam_wr_dma_addr(&dev->cfg, addr, DUMMY_BUF_SIZE, node->pad_id); ++ node->next_frm = NULL; + } + + static inline void unicam_process_buffer_complete(struct unicam_node *node, +@@ -721,7 +748,6 @@ static inline void unicam_process_buffer + node->cur_frm->vb.sequence = sequence; + + vb2_buffer_done(&node->cur_frm->vb.vb2_buf, VB2_BUF_STATE_DONE); +- node->cur_frm = node->next_frm; + } + + static int unicam_num_nodes_streaming(struct unicam_device *dev) +@@ -788,6 +814,28 @@ static irqreturn_t unicam_isr(int irq, v + if (!(sta && (UNICAM_IS | UNICAM_PI0))) + return IRQ_HANDLED; + ++ /* ++ * We must run the frame end handler first. If we have a valid next_frm ++ * and we get a simultaneout FE + FS interrupt, running the FS handler ++ * first would null out the next_frm ptr and we would have lost the ++ * buffer forever. ++ */ ++ if (ista & UNICAM_FEI || sta & UNICAM_PI0) { ++ /* ++ * Ensure we have swapped buffers already as we can't ++ * stop the peripheral. If no buffer is available, use a ++ * dummy buffer to dump out frames until we get a new buffer ++ * to use. ++ */ ++ for (i = 0; i < num_nodes_streaming; i++) { ++ if (unicam->node[i].cur_frm) ++ unicam_process_buffer_complete(&unicam->node[i], ++ sequence); ++ unicam->node[i].cur_frm = unicam->node[i].next_frm; ++ } ++ unicam->sequence++; ++ } ++ + if (ista & UNICAM_FSI) { + /* + * Timestamp is to be when the first data byte was captured, +@@ -798,24 +846,16 @@ static irqreturn_t unicam_isr(int irq, v + if (unicam->node[i].cur_frm) + unicam->node[i].cur_frm->vb.vb2_buf.timestamp = + ts; ++ /* ++ * Set the next frame output to go to a dummy frame ++ * if we have not managed to obtain another frame ++ * from the queue. ++ */ ++ unicam_schedule_dummy_buffer(&unicam->node[i]); + } + } +- if (ista & UNICAM_FEI || sta & UNICAM_PI0) { +- /* +- * Ensure we have swapped buffers already as we can't +- * stop the peripheral. Overwrite the frame we've just +- * captured instead. +- */ +- for (i = 0; i < num_nodes_streaming; i++) { +- if (unicam->node[i].cur_frm && +- unicam->node[i].cur_frm != unicam->node[i].next_frm) +- unicam_process_buffer_complete(&unicam->node[i], +- sequence); +- } +- unicam->sequence++; +- } +- +- /* Cannot swap buffer at frame end, there may be a race condition ++ /* ++ * Cannot swap buffer at frame end, there may be a race condition + * where the HW does not actually swap it if the new frame has + * already started. + */ +@@ -823,7 +863,7 @@ static irqreturn_t unicam_isr(int irq, v + for (i = 0; i < num_nodes_streaming; i++) { + spin_lock(&unicam->node[i].dma_queue_lock); + if (!list_empty(&unicam->node[i].dma_queue.active) && +- unicam->node[i].cur_frm == unicam->node[i].next_frm) ++ !unicam->node[i].next_frm) + unicam_schedule_next_buffer(&unicam->node[i]); + spin_unlock(&unicam->node[i].dma_queue_lock); + } +@@ -1352,7 +1392,7 @@ static void unicam_start_rx(struct unica + { + struct unicam_cfg *cfg = &dev->cfg; + int line_int_freq = dev->node[IMAGE_PAD].v_fmt.fmt.pix.height >> 2; +- unsigned int i; ++ unsigned int size, i; + u32 val; + + if (line_int_freq < 128) +@@ -1413,7 +1453,7 @@ static void unicam_start_rx(struct unica + reg_write_field(cfg, UNICAM_ANA, 0, UNICAM_DDL); + + /* Always start in trigger frame capture mode (UNICAM_FCM set) */ +- val = UNICAM_FSIE | UNICAM_FEIE | UNICAM_FCM; ++ val = UNICAM_FSIE | UNICAM_FEIE | UNICAM_FCM | UNICAM_IBOB; + set_field(&val, line_int_freq, UNICAM_LCIE_MASK); + reg_write(cfg, UNICAM_ICTL, val); + reg_write(cfg, UNICAM_STA, UNICAM_STA_MASK_ALL); +@@ -1501,7 +1541,8 @@ static void unicam_start_rx(struct unica + + reg_write(&dev->cfg, UNICAM_IBLS, + dev->node[IMAGE_PAD].v_fmt.fmt.pix.bytesperline); +- unicam_wr_dma_addr(dev, addr[IMAGE_PAD], IMAGE_PAD); ++ size = dev->node[IMAGE_PAD].v_fmt.fmt.pix.sizeimage; ++ unicam_wr_dma_addr(&dev->cfg, addr[IMAGE_PAD], size, IMAGE_PAD); + unicam_set_packing_config(dev); + unicam_cfg_image_id(dev); + +@@ -1511,8 +1552,10 @@ static void unicam_start_rx(struct unica + reg_write(cfg, UNICAM_MISC, val); + + if (dev->node[METADATA_PAD].streaming && dev->sensor_embedded_data) { ++ size = dev->node[METADATA_PAD].v_fmt.fmt.meta.buffersize; + unicam_enable_ed(dev); +- unicam_wr_dma_addr(dev, addr[METADATA_PAD], METADATA_PAD); ++ unicam_wr_dma_addr(&dev->cfg, addr[METADATA_PAD], size, ++ METADATA_PAD); + } + + /* Enable peripheral */ +@@ -1686,13 +1729,14 @@ static void unicam_stop_streaming(struct + unicam_runtime_put(dev); + + } else if (node->pad_id == METADATA_PAD) { +- /* Null out the embedded data buffer address so the HW does +- * not use it. This is only really needed if the embedded data +- * pad is disabled before the image pad. The 0x3 in the top two +- * bits signifies uncached accesses through the Videocore +- * memory controller. ++ /* Allow the hardware to spin in the dummy buffer. ++ * This is only really needed if the embedded data pad is ++ * disabled before the image pad. The 0x3 in the top two bits ++ * signifies uncached accesses through the Videocore memory ++ * controller. + */ +- unicam_wr_dma_addr(dev, 0xc0000000, METADATA_PAD); ++ unicam_wr_dma_addr(&dev->cfg, node->dummy_buf_dma_addr, ++ DUMMY_BUF_SIZE, METADATA_PAD); + } + + /* Clear all queued buffers for the node */ +@@ -2321,6 +2365,15 @@ static int register_node(struct unicam_d + video_set_drvdata(vdev, node); + vdev->entity.flags |= MEDIA_ENT_FL_DEFAULT; + ++ node->dummy_buf_cpu_addr = dma_alloc_coherent(&unicam->pdev->dev, ++ DUMMY_BUF_SIZE, ++ &node->dummy_buf_dma_addr, ++ GFP_ATOMIC); ++ if (!node->dummy_buf_cpu_addr) { ++ unicam_err(unicam, "Unable to allocate dummy buffer.\n"); ++ return -ENOMEM; ++ } ++ + if (node->pad_id == METADATA_PAD || + !v4l2_subdev_has_op(unicam->sensor, video, s_std)) { + v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_STD); +@@ -2376,13 +2429,20 @@ static int register_node(struct unicam_d + + static void unregister_nodes(struct unicam_device *unicam) + { +- if (unicam->node[IMAGE_PAD].registered) { +- video_unregister_device(&unicam->node[IMAGE_PAD].video_dev); +- unicam->node[IMAGE_PAD].registered = 0; +- } +- if (unicam->node[METADATA_PAD].registered) { +- video_unregister_device(&unicam->node[METADATA_PAD].video_dev); +- unicam->node[METADATA_PAD].registered = 0; ++ struct unicam_node *node; ++ int i; ++ ++ for (i = 0; i < MAX_NODES; i++) { ++ node = &unicam->node[i]; ++ if (node->dummy_buf_cpu_addr) { ++ dma_free_coherent(&unicam->pdev->dev, DUMMY_BUF_SIZE, ++ node->dummy_buf_cpu_addr, ++ node->dummy_buf_dma_addr); ++ } ++ if (node->registered) { ++ video_unregister_device(&node->video_dev); ++ node->registered = 0; ++ } + } + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0215-media-bcm2835-unicam-Disable-event-related-ioctls-on.patch b/target/linux/bcm27xx/patches-5.10/950-0215-media-bcm2835-unicam-Disable-event-related-ioctls-on.patch new file mode 100644 index 0000000000..21b1f39280 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0215-media-bcm2835-unicam-Disable-event-related-ioctls-on.patch @@ -0,0 +1,31 @@ +From 62bd5b64e0213e0b2cf0d0e65e7b0a30399b5e36 Mon Sep 17 00:00:00 2001 +From: Laurent Pinchart +Date: Tue, 24 Mar 2020 23:13:02 +0200 +Subject: [PATCH] media: bcm2835-unicam: Disable event-related ioctls + on metadata node + +The unicam driver supports both the SOURCE_CHANGE and CTRL events. Both +events are only generated on the image video node, so the event-related +ioctls are useless on the medatada node. Disable them. + +Signed-off-by: Laurent Pinchart +Reviewed-by: Jacopo Mondi +Reviewed-by: Naushir Patuck +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 5 +++++ + 1 file changed, 5 insertions(+) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -2374,6 +2374,11 @@ static int register_node(struct unicam_d + return -ENOMEM; + } + ++ if (node->pad_id == METADATA_PAD) { ++ v4l2_disable_ioctl(vdev, VIDIOC_DQEVENT); ++ v4l2_disable_ioctl(vdev, VIDIOC_SUBSCRIBE_EVENT); ++ v4l2_disable_ioctl(vdev, VIDIOC_UNSUBSCRIBE_EVENT); ++ } + if (node->pad_id == METADATA_PAD || + !v4l2_subdev_has_op(unicam->sensor, video, s_std)) { + v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_STD); diff --git a/target/linux/bcm27xx/patches-5.10/950-0216-media-bcm2835-unicam-Add-support-for-the-FRAME_SYNC-.patch b/target/linux/bcm27xx/patches-5.10/950-0216-media-bcm2835-unicam-Add-support-for-the-FRAME_SYNC-.patch new file mode 100644 index 0000000000..40fe0a9750 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0216-media-bcm2835-unicam-Add-support-for-the-FRAME_SYNC-.patch @@ -0,0 +1,55 @@ +From 6195ecf605368d29a9ef684da387a6929845f925 Mon Sep 17 00:00:00 2001 +From: Laurent Pinchart +Date: Tue, 24 Mar 2020 23:13:02 +0200 +Subject: [PATCH] media: bcm2835-unicam: Add support for the FRAME_SYNC + event + +The FRAME_SYNC event is useful for userspace image processing algorithms +to program the camera sensor as early as possible after frame start. +Support it. + +Signed-off-by: Laurent Pinchart +Reviewed-by: Kieran Bingham +Reviewed-by: Jacopo Mondi +Reviewed-by: Naushir Patuck +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 14 ++++++++++++++ + 1 file changed, 14 insertions(+) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -772,6 +772,16 @@ static int unicam_all_nodes_disabled(str + !dev->node[METADATA_PAD].streaming; + } + ++static void unicam_queue_event_sof(struct unicam_device *unicam) ++{ ++ struct v4l2_event event = { ++ .type = V4L2_EVENT_FRAME_SYNC, ++ .u.frame_sync.frame_sequence = unicam->sequence, ++ }; ++ ++ v4l2_event_queue(&unicam->node[IMAGE_PAD].video_dev, &event); ++} ++ + /* + * unicam_isr : ISR handler for unicam capture + * @irq: irq number +@@ -853,6 +863,8 @@ static irqreturn_t unicam_isr(int irq, v + */ + unicam_schedule_dummy_buffer(&unicam->node[i]); + } ++ ++ unicam_queue_event_sof(unicam); + } + /* + * Cannot swap buffer at frame end, there may be a race condition +@@ -2022,6 +2034,8 @@ static int unicam_subscribe_event(struct + const struct v4l2_event_subscription *sub) + { + switch (sub->type) { ++ case V4L2_EVENT_FRAME_SYNC: ++ return v4l2_event_subscribe(fh, sub, 2, NULL); + case V4L2_EVENT_SOURCE_CHANGE: + return v4l2_event_subscribe(fh, sub, 4, NULL); + } diff --git a/target/linux/bcm27xx/patches-5.10/950-0217-media-imx219-Advertise-embedded-data-node-on-media-p.patch b/target/linux/bcm27xx/patches-5.10/950-0217-media-imx219-Advertise-embedded-data-node-on-media-p.patch new file mode 100644 index 0000000000..d8055af5b2 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0217-media-imx219-Advertise-embedded-data-node-on-media-p.patch @@ -0,0 +1,336 @@ +From fde54dfff6652b153af9fab8114b27510b0fe8b4 Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Thu, 12 Mar 2020 14:09:38 +0000 +Subject: [PATCH] media: imx219: Advertise embedded data node on media + pad 1 + +This commit updates the imx219 driver to adverise support for embedded +data streams. This can then be used by the bcm2835-unicam driver, which +has recently been updated to expose the embedded data stream to +userland. + +The imx219 sensor subdevice overloads the media pad to differentiate +between image stream (pad 0) and embedded data stream (pad 1) when +performing the v4l2_subdev_pad_ops functions. + +Signed-off-by: Naushir Patuck +--- + drivers/media/i2c/imx219.c | 226 +++++++++++++++++++++++++------------ + 1 file changed, 155 insertions(+), 71 deletions(-) + +--- a/drivers/media/i2c/imx219.c ++++ b/drivers/media/i2c/imx219.c +@@ -118,6 +118,16 @@ + #define IMX219_PIXEL_ARRAY_WIDTH 3280U + #define IMX219_PIXEL_ARRAY_HEIGHT 2464U + ++/* Embedded metadata stream structure */ ++#define IMX219_EMBEDDED_LINE_WIDTH 16384 ++#define IMX219_NUM_EMBEDDED_LINES 1 ++ ++enum pad_types { ++ IMAGE_PAD, ++ METADATA_PAD, ++ NUM_PADS ++}; ++ + struct imx219_reg { + u16 address; + u8 val; +@@ -536,7 +546,7 @@ static const struct imx219_mode supporte + + struct imx219 { + struct v4l2_subdev sd; +- struct media_pad pad; ++ struct media_pad pad[NUM_PADS]; + + struct v4l2_mbus_framefmt fmt; + +@@ -685,18 +695,26 @@ static void imx219_set_default_format(st + static int imx219_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) + { + struct imx219 *imx219 = to_imx219(sd); +- struct v4l2_mbus_framefmt *try_fmt = +- v4l2_subdev_get_try_format(sd, fh->pad, 0); ++ struct v4l2_mbus_framefmt *try_fmt_img = ++ v4l2_subdev_get_try_format(sd, fh->pad, IMAGE_PAD); ++ struct v4l2_mbus_framefmt *try_fmt_meta = ++ v4l2_subdev_get_try_format(sd, fh->pad, METADATA_PAD); + struct v4l2_rect *try_crop; + + mutex_lock(&imx219->mutex); + +- /* Initialize try_fmt */ +- try_fmt->width = supported_modes[0].width; +- try_fmt->height = supported_modes[0].height; +- try_fmt->code = imx219_get_format_code(imx219, +- MEDIA_BUS_FMT_SRGGB10_1X10); +- try_fmt->field = V4L2_FIELD_NONE; ++ /* Initialize try_fmt for the image pad */ ++ try_fmt_img->width = supported_modes[0].width; ++ try_fmt_img->height = supported_modes[0].height; ++ try_fmt_img->code = imx219_get_format_code(imx219, ++ MEDIA_BUS_FMT_SRGGB10_1X10); ++ try_fmt_img->field = V4L2_FIELD_NONE; ++ ++ /* Initialize try_fmt for the embedded metadata pad */ ++ try_fmt_meta->width = IMX219_EMBEDDED_LINE_WIDTH; ++ try_fmt_meta->height = IMX219_NUM_EMBEDDED_LINES; ++ try_fmt_meta->code = MEDIA_BUS_FMT_SENSOR_DATA; ++ try_fmt_meta->field = V4L2_FIELD_NONE; + + /* Initialize try_crop rectangle. */ + try_crop = v4l2_subdev_get_try_crop(sd, fh->pad, 0); +@@ -805,10 +823,21 @@ static int imx219_enum_mbus_code(struct + { + struct imx219 *imx219 = to_imx219(sd); + +- if (code->index >= (ARRAY_SIZE(codes) / 4)) ++ if (code->pad >= NUM_PADS) + return -EINVAL; + +- code->code = imx219_get_format_code(imx219, codes[code->index * 4]); ++ if (code->pad == IMAGE_PAD) { ++ if (code->index >= (ARRAY_SIZE(codes) / 4)) ++ return -EINVAL; ++ ++ code->code = imx219_get_format_code(imx219, ++ codes[code->index * 4]); ++ } else { ++ if (code->index > 0) ++ return -EINVAL; ++ ++ code->code = MEDIA_BUS_FMT_SENSOR_DATA; ++ } + + return 0; + } +@@ -819,16 +848,29 @@ static int imx219_enum_frame_size(struct + { + struct imx219 *imx219 = to_imx219(sd); + +- if (fse->index >= ARRAY_SIZE(supported_modes)) ++ if (fse->pad >= NUM_PADS) + return -EINVAL; + +- if (fse->code != imx219_get_format_code(imx219, fse->code)) +- return -EINVAL; ++ if (fse->pad == IMAGE_PAD) { ++ if (fse->index >= ARRAY_SIZE(supported_modes)) ++ return -EINVAL; ++ ++ if (fse->code != imx219_get_format_code(imx219, fse->code)) ++ return -EINVAL; ++ ++ fse->min_width = supported_modes[fse->index].width; ++ fse->max_width = fse->min_width; ++ fse->min_height = supported_modes[fse->index].height; ++ fse->max_height = fse->min_height; ++ } else { ++ if (fse->code != MEDIA_BUS_FMT_SENSOR_DATA || fse->index > 0) ++ return -EINVAL; + +- fse->min_width = supported_modes[fse->index].width; +- fse->max_width = fse->min_width; +- fse->min_height = supported_modes[fse->index].height; +- fse->max_height = fse->min_height; ++ fse->min_width = IMX219_EMBEDDED_LINE_WIDTH; ++ fse->max_width = fse->min_width; ++ fse->min_height = IMX219_NUM_EMBEDDED_LINES; ++ fse->max_height = fse->min_height; ++ } + + return 0; + } +@@ -843,9 +885,9 @@ static void imx219_reset_colorspace(stru + fmt->xfer_func = V4L2_MAP_XFER_FUNC_DEFAULT(fmt->colorspace); + } + +-static void imx219_update_pad_format(struct imx219 *imx219, +- const struct imx219_mode *mode, +- struct v4l2_subdev_format *fmt) ++static void imx219_update_image_pad_format(struct imx219 *imx219, ++ const struct imx219_mode *mode, ++ struct v4l2_subdev_format *fmt) + { + fmt->format.width = mode->width; + fmt->format.height = mode->height; +@@ -853,20 +895,38 @@ static void imx219_update_pad_format(str + imx219_reset_colorspace(&fmt->format); + } + ++static void imx219_update_metadata_pad_format(struct v4l2_subdev_format *fmt) ++{ ++ fmt->format.width = IMX219_EMBEDDED_LINE_WIDTH; ++ fmt->format.height = IMX219_NUM_EMBEDDED_LINES; ++ fmt->format.code = MEDIA_BUS_FMT_SENSOR_DATA; ++ fmt->format.field = V4L2_FIELD_NONE; ++} ++ + static int __imx219_get_pad_format(struct imx219 *imx219, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_format *fmt) + { ++ if (fmt->pad >= NUM_PADS) ++ return -EINVAL; ++ + if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { + struct v4l2_mbus_framefmt *try_fmt = + v4l2_subdev_get_try_format(&imx219->sd, cfg, fmt->pad); + /* update the code which could change due to vflip or hflip: */ +- try_fmt->code = imx219_get_format_code(imx219, try_fmt->code); ++ try_fmt->code = fmt->pad == IMAGE_PAD ? ++ imx219_get_format_code(imx219, try_fmt->code) : ++ MEDIA_BUS_FMT_SENSOR_DATA; + fmt->format = *try_fmt; + } else { +- imx219_update_pad_format(imx219, imx219->mode, fmt); +- fmt->format.code = imx219_get_format_code(imx219, +- imx219->fmt.code); ++ if (fmt->pad == IMAGE_PAD) { ++ imx219_update_image_pad_format(imx219, imx219->mode, ++ fmt); ++ fmt->format.code = imx219_get_format_code(imx219, ++ imx219->fmt.code); ++ } else { ++ imx219_update_metadata_pad_format(fmt); ++ } + } + + return 0; +@@ -896,51 +956,74 @@ static int imx219_set_pad_format(struct + int exposure_max, exposure_def, hblank; + unsigned int i; + +- mutex_lock(&imx219->mutex); +- +- for (i = 0; i < ARRAY_SIZE(codes); i++) +- if (codes[i] == fmt->format.code) +- break; +- if (i >= ARRAY_SIZE(codes)) +- i = 0; ++ if (fmt->pad >= NUM_PADS) ++ return -EINVAL; + +- /* Bayer order varies with flips */ +- fmt->format.code = imx219_get_format_code(imx219, codes[i]); ++ mutex_lock(&imx219->mutex); + +- mode = v4l2_find_nearest_size(supported_modes, +- ARRAY_SIZE(supported_modes), +- width, height, +- fmt->format.width, fmt->format.height); +- imx219_update_pad_format(imx219, mode, fmt); +- if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { +- framefmt = v4l2_subdev_get_try_format(sd, cfg, fmt->pad); +- *framefmt = fmt->format; +- } else if (imx219->mode != mode || +- imx219->fmt.code != fmt->format.code) { +- imx219->fmt = fmt->format; +- imx219->mode = mode; +- /* Update limits and set FPS to default */ +- __v4l2_ctrl_modify_range(imx219->vblank, IMX219_VBLANK_MIN, +- IMX219_VTS_MAX - mode->height, 1, +- mode->vts_def - mode->height); +- __v4l2_ctrl_s_ctrl(imx219->vblank, +- mode->vts_def - mode->height); +- /* Update max exposure while meeting expected vblanking */ +- exposure_max = mode->vts_def - 4; +- exposure_def = (exposure_max < IMX219_EXPOSURE_DEFAULT) ? +- exposure_max : IMX219_EXPOSURE_DEFAULT; +- __v4l2_ctrl_modify_range(imx219->exposure, +- imx219->exposure->minimum, +- exposure_max, imx219->exposure->step, +- exposure_def); +- /* +- * Currently PPL is fixed to IMX219_PPL_DEFAULT, so hblank +- * depends on mode->width only, and is not changeble in any +- * way other than changing the mode. +- */ +- hblank = IMX219_PPL_DEFAULT - mode->width; +- __v4l2_ctrl_modify_range(imx219->hblank, hblank, hblank, 1, +- hblank); ++ if (fmt->pad == IMAGE_PAD) { ++ for (i = 0; i < ARRAY_SIZE(codes); i++) ++ if (codes[i] == fmt->format.code) ++ break; ++ if (i >= ARRAY_SIZE(codes)) ++ i = 0; ++ ++ /* Bayer order varies with flips */ ++ fmt->format.code = imx219_get_format_code(imx219, codes[i]); ++ ++ mode = v4l2_find_nearest_size(supported_modes, ++ ARRAY_SIZE(supported_modes), ++ width, height, ++ fmt->format.width, ++ fmt->format.height); ++ imx219_update_image_pad_format(imx219, mode, fmt); ++ if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { ++ framefmt = v4l2_subdev_get_try_format(sd, cfg, ++ fmt->pad); ++ *framefmt = fmt->format; ++ } else if (imx219->mode != mode || ++ imx219->fmt.code != fmt->format.code) { ++ imx219->fmt = fmt->format; ++ imx219->mode = mode; ++ /* Update limits and set FPS to default */ ++ __v4l2_ctrl_modify_range(imx219->vblank, ++ IMX219_VBLANK_MIN, ++ IMX219_VTS_MAX - mode->height, ++ 1, ++ mode->vts_def - mode->height); ++ __v4l2_ctrl_s_ctrl(imx219->vblank, ++ mode->vts_def - mode->height); ++ /* ++ * Update max exposure while meeting ++ * expected vblanking ++ */ ++ exposure_max = mode->vts_def - 4; ++ exposure_def = ++ (exposure_max < IMX219_EXPOSURE_DEFAULT) ? ++ exposure_max : IMX219_EXPOSURE_DEFAULT; ++ __v4l2_ctrl_modify_range(imx219->exposure, ++ imx219->exposure->minimum, ++ exposure_max, ++ imx219->exposure->step, ++ exposure_def); ++ /* ++ * Currently PPL is fixed to IMX219_PPL_DEFAULT, so ++ * hblank depends on mode->width only, and is not ++ * changeble in any way other than changing the mode. ++ */ ++ hblank = IMX219_PPL_DEFAULT - mode->width; ++ __v4l2_ctrl_modify_range(imx219->hblank, hblank, hblank, ++ 1, hblank); ++ } ++ } else { ++ if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { ++ framefmt = v4l2_subdev_get_try_format(sd, cfg, ++ fmt->pad); ++ *framefmt = fmt->format; ++ } else { ++ /* Only one embedded data mode is supported */ ++ imx219_update_metadata_pad_format(fmt); ++ } + } + + mutex_unlock(&imx219->mutex); +@@ -1511,13 +1594,14 @@ static int imx219_probe(struct i2c_clien + imx219->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; + imx219->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR; + +- /* Initialize source pad */ +- imx219->pad.flags = MEDIA_PAD_FL_SOURCE; ++ /* Initialize source pads */ ++ imx219->pad[IMAGE_PAD].flags = MEDIA_PAD_FL_SOURCE; ++ imx219->pad[METADATA_PAD].flags = MEDIA_PAD_FL_SOURCE; + + /* Initialize default format */ + imx219_set_default_format(imx219); + +- ret = media_entity_pads_init(&imx219->sd.entity, 1, &imx219->pad); ++ ret = media_entity_pads_init(&imx219->sd.entity, NUM_PADS, imx219->pad); + if (ret) { + dev_err(dev, "failed to init entity pads: %d\n", ret); + goto error_handler_free; diff --git a/target/linux/bcm27xx/patches-5.10/950-0218-media-bcm2835-unicam-Re-fetch-mbus-code-from-subdev-.patch b/target/linux/bcm27xx/patches-5.10/950-0218-media-bcm2835-unicam-Re-fetch-mbus-code-from-subdev-.patch new file mode 100644 index 0000000000..3bd8c0fc58 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0218-media-bcm2835-unicam-Re-fetch-mbus-code-from-subdev-.patch @@ -0,0 +1,49 @@ +From e2eb4940fd6b819d4db64e2822a2ffca7ee0a7f3 Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Tue, 21 Apr 2020 16:26:03 +0100 +Subject: [PATCH] media: bcm2835-unicam: Re-fetch mbus code from subdev + on a g_fmt call + +The sensor subdevice may change the Bayer order if a H/V flip is +requested after a s_fmt call. Unicam g_fmt must call the subdev get_fmt +in case this has happened and return out the correct format 4cc. + +Signed-off-by: Naushir Patuck +--- + .../media/platform/bcm2835/bcm2835-unicam.c | 21 ++++++++++++++++++- + 1 file changed, 20 insertions(+), 1 deletion(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -967,11 +967,30 @@ static int unicam_enum_fmt_vid_cap(struc + static int unicam_g_fmt_vid_cap(struct file *file, void *priv, + struct v4l2_format *f) + { ++ struct v4l2_mbus_framefmt mbus_fmt = {0}; + struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ const struct unicam_fmt *fmt = NULL; ++ int ret; + +- if (node->pad_id == METADATA_PAD) ++ if (node->pad_id != IMAGE_PAD) + return -EINVAL; + ++ /* ++ * If a flip has occurred in the sensor, the fmt code might have ++ * changed. So we will need to re-fetch the format from the subdevice. ++ */ ++ ret = __subdev_get_format(dev, &mbus_fmt, node->pad_id); ++ if (ret) ++ return -EINVAL; ++ ++ /* Find the V4L2 format from mbus code. We must match a known format. */ ++ fmt = find_format_by_code(mbus_fmt.code); ++ if (!fmt) ++ return -EINVAL; ++ ++ node->fmt = fmt; ++ node->v_fmt.fmt.pix.pixelformat = fmt->fourcc; + *f = node->v_fmt; + + return 0; diff --git a/target/linux/bcm27xx/patches-5.10/950-0219-media-uapi-v4l2-core-Add-ISP-statistics-output-V4L2-.patch b/target/linux/bcm27xx/patches-5.10/950-0219-media-uapi-v4l2-core-Add-ISP-statistics-output-V4L2-.patch new file mode 100644 index 0000000000..a2974a98b4 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0219-media-uapi-v4l2-core-Add-ISP-statistics-output-V4L2-.patch @@ -0,0 +1,94 @@ +From 4e9d4f3927e2e9b5fae5fefe4faf82d5ecfc86cd Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Thu, 23 Apr 2020 10:20:26 +0100 +Subject: [PATCH] media: uapi: v4l2-core: Add ISP statistics output + V4L2 fourcc type + +Add V4L2_META_FMT_BCM2835_ISP_STATS V4L2 format type. + +This new format will be used by the BCM2835 ISP device to return +out ISP statistics for 3A. + +Signed-off-by: Naushir Patuck +--- + .../userspace-api/media/v4l/meta-formats.rst | 1 + + .../v4l/pixfmt-meta-bcm2835-isp-stats.rst | 41 +++++++++++++++++++ + drivers/media/v4l2-core/v4l2-ioctl.c | 1 + + include/uapi/linux/videodev2.h | 1 + + 4 files changed, 44 insertions(+) + create mode 100644 Documentation/userspace-api/media/v4l/pixfmt-meta-bcm2835-isp-stats.rst + +--- a/Documentation/userspace-api/media/v4l/meta-formats.rst ++++ b/Documentation/userspace-api/media/v4l/meta-formats.rst +@@ -12,6 +12,7 @@ These formats are used for the :ref:`met + .. toctree:: + :maxdepth: 1 + ++ pixfmt-meta-bcm2835-isp-stats + pixfmt-meta-d4xx + pixfmt-meta-intel-ipu3 + pixfmt-meta-rkisp1 +--- /dev/null ++++ b/Documentation/userspace-api/media/v4l/pixfmt-meta-bcm2835-isp-stats.rst +@@ -0,0 +1,41 @@ ++.. Permission is granted to copy, distribute and/or modify this ++.. document under the terms of the GNU Free Documentation License, ++.. Version 1.1 or any later version published by the Free Software ++.. Foundation, with no Invariant Sections, no Front-Cover Texts ++.. and no Back-Cover Texts. A copy of the license is included at ++.. Documentation/media/uapi/fdl-appendix.rst. ++.. ++.. TODO: replace it to GFDL-1.1-or-later WITH no-invariant-sections ++ ++.. _v4l2-meta-fmt-bcm2835-isp-stats: ++ ++***************************************** ++V4L2_META_FMT_BCM2835_ISP_STATS ('BSTA') ++***************************************** ++ ++BCM2835 ISP Statistics ++ ++Description ++=========== ++ ++The BCM2835 ISP hardware calculate image statistics for an input Bayer frame. ++These statistics are obtained from the "bcm2835-isp0-capture3" device node ++using the :c:type:`v4l2_meta_format` interface. They are formatted as described ++by the :c:type:`bcm2835_isp_stats` structure below. ++ ++.. code-block:: c ++ ++ #define DEFAULT_AWB_REGIONS_X 16 ++ #define DEFAULT_AWB_REGIONS_Y 12 ++ ++ #define NUM_HISTOGRAMS 2 ++ #define NUM_HISTOGRAM_BINS 128 ++ #define AWB_REGIONS (DEFAULT_AWB_REGIONS_X * DEFAULT_AWB_REGIONS_Y) ++ #define FLOATING_REGIONS 16 ++ #define AGC_REGIONS 16 ++ #define FOCUS_REGIONS 12 ++ ++.. kernel-doc:: include/uapi/linux/bcm2835-isp.h ++ :functions: bcm2835_isp_stats_hist bcm2835_isp_stats_region ++ bcm2835_isp_stats_focus bcm2835_isp_stats ++ +--- a/drivers/media/v4l2-core/v4l2-ioctl.c ++++ b/drivers/media/v4l2-core/v4l2-ioctl.c +@@ -1405,6 +1405,7 @@ static void v4l_fill_fmtdesc(struct v4l2 + case V4L2_META_FMT_D4XX: descr = "Intel D4xx UVC Metadata"; break; + case V4L2_META_FMT_VIVID: descr = "Vivid Metadata"; break; + case V4L2_META_FMT_SENSOR_DATA: descr = "Sensor Ancillary Metadata"; break; ++ case V4L2_META_FMT_BCM2835_ISP_STATS: descr = "BCM2835 ISP Image Statistics"; break; + + default: + /* Compressed formats */ +--- a/include/uapi/linux/videodev2.h ++++ b/include/uapi/linux/videodev2.h +@@ -779,6 +779,7 @@ struct v4l2_pix_format { + #define V4L2_META_FMT_D4XX v4l2_fourcc('D', '4', 'X', 'X') /* D4XX Payload Header metadata */ + #define V4L2_META_FMT_VIVID v4l2_fourcc('V', 'I', 'V', 'D') /* Vivid Metadata */ + #define V4L2_META_FMT_SENSOR_DATA v4l2_fourcc('S', 'E', 'N', 'S') /* Sensor Ancillary metadata */ ++#define V4L2_META_FMT_BCM2835_ISP_STATS v4l2_fourcc('B', 'S', 'T', 'A') /* BCM2835 ISP image statistics output */ + + /* priv field value to indicates that subsequent fields are valid. */ + #define V4L2_PIX_FMT_PRIV_MAGIC 0xfeedcafe diff --git a/target/linux/bcm27xx/patches-5.10/950-0220-media-uapi-v4l-ctrls-Add-CID-base-for-the-bcm2835-is.patch b/target/linux/bcm27xx/patches-5.10/950-0220-media-uapi-v4l-ctrls-Add-CID-base-for-the-bcm2835-is.patch new file mode 100644 index 0000000000..ec838bc50b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0220-media-uapi-v4l-ctrls-Add-CID-base-for-the-bcm2835-is.patch @@ -0,0 +1,169 @@ +From 1dccb28000e0b12b5796a682f1995bdf0f38f7e5 Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Tue, 21 Apr 2020 15:06:19 +0100 +Subject: [PATCH] media: uapi: v4l-ctrls: Add CID base for the + bcm2835-isp driver + +We are reserving controls for the new bcm2835-isp driver. + +Signed-off-by: Naushir Patuck +--- + .../admin-guide/media/bcm2835-isp.rst | 127 ++++++++++++++++++ + .../userspace-api/media/drivers/index.rst | 1 + + include/uapi/linux/v4l2-controls.h | 4 + + 3 files changed, 132 insertions(+) + create mode 100644 Documentation/admin-guide/media/bcm2835-isp.rst + +--- /dev/null ++++ b/Documentation/admin-guide/media/bcm2835-isp.rst +@@ -0,0 +1,127 @@ ++.. SPDX-License-Identifier: GPL-2.0 ++ ++BCM2835 ISP Driver ++================== ++ ++Introduction ++------------ ++ ++The BCM2835 Image Sensor Pipeline (ISP) is a fixed function hardware pipeline ++for performing image processing operations. Images are fed to the input ++of the ISP through memory frame buffers. These images may be in various YUV, ++RGB, or Bayer formats. A typical use case would have Bayer images obtained from ++an image sensor by the BCM2835 Unicam peripheral, written to a memory ++frame buffer, and finally fed into the input of the ISP. Two concurrent output ++images may be generated in YUV or RGB format at different resolutions. ++Statistics output is also generated for Bayer input images. ++ ++The bcm2835-isp driver exposes the following media pads as V4L2 device nodes: ++ ++.. tabularcolumns:: |l|l|l|l| ++ ++.. cssclass: longtable ++ ++.. flat-table:: ++ ++ * - *Pad* ++ - *Direction* ++ - *Purpose* ++ - *Formats* ++ ++ * - "bcm2835-isp0-output0" ++ - sink ++ - Accepts Bayer, RGB or YUV format frame buffers as input to the ISP HW ++ pipeline. ++ - :ref:`RAW8 `, ++ :ref:`RAW10P `, ++ :ref:`RAW12P `, ++ :ref:`RAW14P `, ++ :ref:`RAW16 `, ++ :ref:`RGB24/BGR24 `, ++ :ref:`YUYV `, ++ :ref:`YVYU `, ++ :ref:`UYVY `, ++ :ref:`VYUY `, ++ :ref:`YUV420/YVU420 ` ++ ++ * - "bcm2835-isp0-capture1" ++ - source ++ - High resolution YUV or RGB processed output from the ISP. ++ - :ref:`RGB565 `, ++ :ref:`RGB24/BGR24 `, ++ :ref:`ABGR32 `, ++ :ref:`YUYV `, ++ :ref:`YVYU `, ++ :ref:`UYVY `, ++ :ref:`VYUY `. ++ :ref:`YUV420/YVU420 `, ++ :ref:`NV12/NV21 `, ++ ++ * - "bcm2835-isp0-capture2" ++ - source ++ - Low resolution YUV processed output from the ISP. The output of ++ this pad cannot have a resolution larger than the "bcm2835-isp0-capture1" pad in any dimension. ++ - :ref:`YUYV `, ++ :ref:`YVYU `, ++ :ref:`UYVY `, ++ :ref:`VYUY `. ++ :ref:`YUV420/YVU420 `, ++ :ref:`NV12/NV21 `, ++ ++ * - "bcm2835-isp0-capture1" ++ - source ++ - Image statistics calculated from the input image provided on the ++ "bcm2835-isp0-output0" pad. Statistics are only available for Bayer ++ format input images. ++ - :ref:`v4l2-meta-fmt-bcm2835-isp-stats`. ++ ++Pipeline Configuration ++---------------------- ++ ++The ISP pipeline can be configure through user-space by calling ++:ref:`VIDIOC_S_EXT_CTRLS ` on the “bcm2835-isp0-output0” ++node with the appropriate parameters as shown in the table below. ++ ++.. tabularcolumns:: |p{2cm}|p{5.0cm}| ++ ++.. cssclass: longtable ++ ++.. flat-table:: ++ ++ * - *id* ++ - *Parameter* ++ ++ * - ``V4L2_CID_USER_BCM2835_ISP_CC_MATRIX`` ++ - struct :c:type:`bcm2835_isp_custom_ccm` ++ ++ * - ``V4L2_CID_USER_BCM2835_ISP_LENS_SHADING`` ++ - struct :c:type:`bcm2835_isp_lens_shading` ++ ++ * - ``V4L2_CID_USER_BCM2835_ISP_BLACK_LEVEL`` ++ - struct :c:type:`bcm2835_isp_black_level` ++ ++ * - ``V4L2_CID_USER_BCM2835_ISP_GEQ`` ++ - struct :c:type:`bcm2835_isp_geq` ++ ++ * - ``V4L2_CID_USER_BCM2835_ISP_GAMMA`` ++ - struct :c:type:`bcm2835_isp_gamma` ++ ++ * - ``V4L2_CID_USER_BCM2835_ISP_DENOISE`` ++ - struct :c:type:`bcm2835_isp_denoise` ++ ++ * - ``V4L2_CID_USER_BCM2835_ISP_SHARPEN`` ++ - struct :c:type:`bcm2835_isp_sharpen` ++ ++ * - ``V4L2_CID_USER_BCM2835_ISP_DPC`` ++ - struct :c:type:`bcm2835_isp_dpc` ++ ++++++++++++++++++++++++++ ++Configuration Parameters ++++++++++++++++++++++++++ ++ ++.. kernel-doc:: include/uapi/linux/bcm2835-isp.h ++ :functions: bcm2835_isp_rational bcm2835_isp_ccm bcm2835_isp_custom_ccm ++ bcm2835_isp_gain_format bcm2835_isp_lens_shading ++ bcm2835_isp_black_level bcm2835_isp_geq bcm2835_isp_gamma ++ bcm2835_isp_denoise bcm2835_isp_sharpen ++ bcm2835_isp_dpc_mode bcm2835_isp_dpc +--- a/Documentation/userspace-api/media/drivers/index.rst ++++ b/Documentation/userspace-api/media/drivers/index.rst +@@ -33,6 +33,7 @@ For more details see the file COPYING in + + cx2341x-uapi + imx-uapi ++ bcm2835-isp + max2175 + meye-uapi + omap3isp-uapi +--- a/include/uapi/linux/v4l2-controls.h ++++ b/include/uapi/linux/v4l2-controls.h +@@ -198,6 +198,10 @@ enum v4l2_colorfx { + */ + #define V4L2_CID_USER_ATMEL_ISC_BASE (V4L2_CID_USER_BASE + 0x10c0) + ++/* The base for the bcm2835-isp driver controls. ++ * We reserve 16 controls for this driver. */ ++#define V4L2_CID_USER_BCM2835_ISP_BASE (V4L2_CID_USER_BASE + 0x10e0) ++ + /* MPEG-class control IDs */ + /* The MPEG controls are applicable to all codec controls + * and the 'MPEG' part of the define is historical */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0221-staging-vchiq-Load-bcm2835_isp-driver-from-vchiq.patch b/target/linux/bcm27xx/patches-5.10/950-0221-staging-vchiq-Load-bcm2835_isp-driver-from-vchiq.patch new file mode 100644 index 0000000000..e621e74073 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0221-staging-vchiq-Load-bcm2835_isp-driver-from-vchiq.patch @@ -0,0 +1,39 @@ +From c05548e7942540ef85c096853d56114816e92a39 Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Wed, 22 Apr 2020 08:32:32 +0100 +Subject: [PATCH] staging: vchiq: Load bcm2835_isp driver from vchiq + +bcmn2835_isp is a platform driver dependent on vchiq, +therefore add the load/unload functions for it to vchiq. + +Signed-off-by: Naushir Patuck +--- + drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c ++++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c +@@ -111,6 +111,7 @@ static struct platform_device *bcm2835_c + static struct platform_device *bcm2835_audio; + static struct platform_device *bcm2835_codec; + static struct platform_device *vcsm_cma; ++static struct platform_device *bcm2835_isp; + + static struct vchiq_drvdata bcm2835_drvdata = { + .cache_line_size = 32, +@@ -2796,6 +2797,7 @@ static int vchiq_probe(struct platform_d + bcm2835_codec = vchiq_register_child(pdev, "bcm2835-codec"); + bcm2835_camera = vchiq_register_child(pdev, "bcm2835-camera"); + bcm2835_audio = vchiq_register_child(pdev, "bcm2835_audio"); ++ bcm2835_isp = vchiq_register_child(pdev, "bcm2835-isp"); + + return 0; + +@@ -2808,6 +2810,7 @@ failed_platform_init: + + static int vchiq_remove(struct platform_device *pdev) + { ++ platform_device_unregister(bcm2835_isp); + platform_device_unregister(bcm2835_audio); + platform_device_unregister(bcm2835_camera); + platform_device_unregister(bcm2835_codec); diff --git a/target/linux/bcm27xx/patches-5.10/950-0222-bcm2835-dma-Add-proper-40-bit-DMA-support.patch b/target/linux/bcm27xx/patches-5.10/950-0222-bcm2835-dma-Add-proper-40-bit-DMA-support.patch new file mode 100644 index 0000000000..12291834b1 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0222-bcm2835-dma-Add-proper-40-bit-DMA-support.patch @@ -0,0 +1,801 @@ +From e53a536e7a182f97adf5394c4ef621a30adf6543 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 4 Apr 2019 13:33:47 +0100 +Subject: [PATCH] bcm2835-dma: Add proper 40-bit DMA support + +BCM2711 has 4 DMA channels with a 40-bit address range, allowing them +to access the full 4GB of memory on a Pi 4. + +Signed-off-by: Phil Elwell +--- + drivers/dma/bcm2835-dma.c | 485 ++++++++++++++++++++++++++++++++------ + 1 file changed, 412 insertions(+), 73 deletions(-) + +--- a/drivers/dma/bcm2835-dma.c ++++ b/drivers/dma/bcm2835-dma.c +@@ -38,6 +38,11 @@ + #define BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED 14 + #define BCM2835_DMA_CHAN_NAME_SIZE 8 + #define BCM2835_DMA_BULK_MASK BIT(0) ++#define BCM2711_DMA_MEMCPY_CHAN 14 ++ ++struct bcm2835_dma_cfg_data { ++ u32 chan_40bit_mask; ++}; + + /** + * struct bcm2835_dmadev - BCM2835 DMA controller +@@ -50,6 +55,7 @@ struct bcm2835_dmadev { + struct dma_device ddev; + void __iomem *base; + dma_addr_t zero_page; ++ const struct bcm2835_dma_cfg_data *cfg_data; + }; + + struct bcm2835_dma_cb { +@@ -62,6 +68,17 @@ struct bcm2835_dma_cb { + uint32_t pad[2]; + }; + ++struct bcm2711_dma40_scb { ++ uint32_t ti; ++ uint32_t src; ++ uint32_t srci; ++ uint32_t dst; ++ uint32_t dsti; ++ uint32_t len; ++ uint32_t next_cb; ++ uint32_t rsvd; ++}; ++ + struct bcm2835_cb_entry { + struct bcm2835_dma_cb *cb; + dma_addr_t paddr; +@@ -82,6 +99,7 @@ struct bcm2835_chan { + unsigned int irq_flags; + + bool is_lite_channel; ++ bool is_40bit_channel; + }; + + struct bcm2835_desc { +@@ -171,13 +189,118 @@ struct bcm2835_desc { + #define BCM2835_DMA_DATA_TYPE_S128 16 + + /* Valid only for channels 0 - 14, 15 has its own base address */ +-#define BCM2835_DMA_CHAN(n) ((n) << 8) /* Base address */ ++#define BCM2835_DMA_CHAN_SIZE 0x100 ++#define BCM2835_DMA_CHAN(n) ((n) * BCM2835_DMA_CHAN_SIZE) /* Base address */ + #define BCM2835_DMA_CHANIO(base, n) ((base) + BCM2835_DMA_CHAN(n)) + + /* the max dma length for different channels */ + #define MAX_DMA_LEN SZ_1G + #define MAX_LITE_DMA_LEN (SZ_64K - 4) + ++/* 40-bit DMA support */ ++#define BCM2711_DMA40_CS 0x00 ++#define BCM2711_DMA40_CB 0x04 ++#define BCM2711_DMA40_DEBUG 0x0c ++#define BCM2711_DMA40_TI 0x10 ++#define BCM2711_DMA40_SRC 0x14 ++#define BCM2711_DMA40_SRCI 0x18 ++#define BCM2711_DMA40_DEST 0x1c ++#define BCM2711_DMA40_DESTI 0x20 ++#define BCM2711_DMA40_LEN 0x24 ++#define BCM2711_DMA40_NEXT_CB 0x28 ++#define BCM2711_DMA40_DEBUG2 0x2c ++ ++#define BCM2711_DMA40_ACTIVE BIT(0) ++#define BCM2711_DMA40_END BIT(1) ++#define BCM2711_DMA40_INT BIT(2) ++#define BCM2711_DMA40_DREQ BIT(3) /* DREQ state */ ++#define BCM2711_DMA40_RD_PAUSED BIT(4) /* Reading is paused */ ++#define BCM2711_DMA40_WR_PAUSED BIT(5) /* Writing is paused */ ++#define BCM2711_DMA40_DREQ_PAUSED BIT(6) /* Is paused by DREQ flow control */ ++#define BCM2711_DMA40_WAITING_FOR_WRITES BIT(7) /* Waiting for last write */ ++#define BCM2711_DMA40_ERR BIT(10) ++#define BCM2711_DMA40_QOS(x) (((x) & 0x1f) << 16) ++#define BCM2711_DMA40_PANIC_QOS(x) (((x) & 0x1f) << 20) ++#define BCM2711_DMA40_WAIT_FOR_WRITES BIT(28) ++#define BCM2711_DMA40_DISDEBUG BIT(29) ++#define BCM2711_DMA40_ABORT BIT(30) ++#define BCM2711_DMA40_HALT BIT(31) ++#define BCM2711_DMA40_CS_FLAGS(x) (x & (BCM2711_DMA40_QOS(15) | \ ++ BCM2711_DMA40_PANIC_QOS(15) | \ ++ BCM2711_DMA40_WAIT_FOR_WRITES | \ ++ BCM2711_DMA40_DISDEBUG)) ++ ++/* Transfer information bits */ ++#define BCM2711_DMA40_INTEN BIT(0) ++#define BCM2711_DMA40_TDMODE BIT(1) /* 2D-Mode */ ++#define BCM2711_DMA40_WAIT_RESP BIT(2) /* wait for AXI write to be acked */ ++#define BCM2711_DMA40_WAIT_RD_RESP BIT(3) /* wait for AXI read to complete */ ++#define BCM2711_DMA40_PER_MAP(x) ((x & 31) << 9) /* REQ source */ ++#define BCM2711_DMA40_S_DREQ BIT(14) /* enable SREQ for source */ ++#define BCM2711_DMA40_D_DREQ BIT(15) /* enable DREQ for destination */ ++#define BCM2711_DMA40_S_WAIT(x) ((x & 0xff) << 16) /* add DMA read-wait cycles */ ++#define BCM2711_DMA40_D_WAIT(x) ((x & 0xff) << 24) /* add DMA write-wait cycles */ ++ ++/* debug register bits */ ++#define BCM2711_DMA40_DEBUG_WRITE_ERR BIT(0) ++#define BCM2711_DMA40_DEBUG_FIFO_ERR BIT(1) ++#define BCM2711_DMA40_DEBUG_READ_ERR BIT(2) ++#define BCM2711_DMA40_DEBUG_READ_CB_ERR BIT(3) ++#define BCM2711_DMA40_DEBUG_IN_ON_ERR BIT(8) ++#define BCM2711_DMA40_DEBUG_ABORT_ON_ERR BIT(9) ++#define BCM2711_DMA40_DEBUG_HALT_ON_ERR BIT(10) ++#define BCM2711_DMA40_DEBUG_DISABLE_CLK_GATE BIT(11) ++#define BCM2711_DMA40_DEBUG_RSTATE_SHIFT 14 ++#define BCM2711_DMA40_DEBUG_RSTATE_BITS 4 ++#define BCM2711_DMA40_DEBUG_WSTATE_SHIFT 18 ++#define BCM2711_DMA40_DEBUG_WSTATE_BITS 4 ++#define BCM2711_DMA40_DEBUG_RESET BIT(23) ++#define BCM2711_DMA40_DEBUG_ID_SHIFT 24 ++#define BCM2711_DMA40_DEBUG_ID_BITS 4 ++#define BCM2711_DMA40_DEBUG_VERSION_SHIFT 28 ++#define BCM2711_DMA40_DEBUG_VERSION_BITS 4 ++ ++/* Valid only for channels 0 - 3 (11 - 14) */ ++#define BCM2711_DMA40_CHAN(n) (((n) + 11) << 8) /* Base address */ ++#define BCM2711_DMA40_CHANIO(base, n) ((base) + BCM2711_DMA_CHAN(n)) ++ ++/* the max dma length for different channels */ ++#define MAX_DMA40_LEN SZ_1G ++ ++#define BCM2711_DMA40_BURST_LEN(x) ((min(x,16) - 1) << 8) ++#define BCM2711_DMA40_INC BIT(12) ++#define BCM2711_DMA40_SIZE_32 (0 << 13) ++#define BCM2711_DMA40_SIZE_64 (1 << 13) ++#define BCM2711_DMA40_SIZE_128 (2 << 13) ++#define BCM2711_DMA40_SIZE_256 (3 << 13) ++#define BCM2711_DMA40_IGNORE BIT(15) ++#define BCM2711_DMA40_STRIDE(x) ((x) << 16) /* For 2D mode */ ++ ++#define BCM2711_DMA40_MEMCPY_FLAGS \ ++ (BCM2711_DMA40_QOS(0) | \ ++ BCM2711_DMA40_PANIC_QOS(0) | \ ++ BCM2711_DMA40_WAIT_FOR_WRITES | \ ++ BCM2711_DMA40_DISDEBUG) ++ ++#define BCM2711_DMA40_MEMCPY_XFER_INFO \ ++ (BCM2711_DMA40_SIZE_128 | \ ++ BCM2711_DMA40_INC | \ ++ BCM2711_DMA40_BURST_LEN(16)) ++ ++struct bcm2835_dmadev *memcpy_parent; ++static void __iomem *memcpy_chan; ++static struct bcm2711_dma40_scb *memcpy_scb; ++static dma_addr_t memcpy_scb_dma; ++DEFINE_SPINLOCK(memcpy_lock); ++ ++static const struct bcm2835_dma_cfg_data bcm2835_dma_cfg = { ++ .chan_40bit_mask = 0, ++}; ++ ++static const struct bcm2835_dma_cfg_data bcm2711_dma_cfg = { ++ .chan_40bit_mask = BIT(11) | BIT(12) | BIT(13) | BIT(14), ++}; ++ + static inline size_t bcm2835_dma_max_frame_length(struct bcm2835_chan *c) + { + /* lite and normal channels have different max frame length */ +@@ -207,6 +330,32 @@ static inline struct bcm2835_desc *to_bc + return container_of(t, struct bcm2835_desc, vd.tx); + } + ++static inline uint32_t to_bcm2711_ti(uint32_t info) ++{ ++ return ((info & BCM2835_DMA_INT_EN) ? BCM2711_DMA40_INTEN : 0) | ++ ((info & BCM2835_DMA_WAIT_RESP) ? BCM2711_DMA40_WAIT_RESP : 0) | ++ ((info & BCM2835_DMA_S_DREQ) ? ++ (BCM2711_DMA40_S_DREQ | BCM2711_DMA40_WAIT_RD_RESP) : 0) | ++ ((info & BCM2835_DMA_D_DREQ) ? BCM2711_DMA40_D_DREQ : 0) | ++ BCM2711_DMA40_PER_MAP((info >> 16) & 0x1f); ++} ++ ++static inline uint32_t to_bcm2711_srci(uint32_t info) ++{ ++ return ((info & BCM2835_DMA_S_INC) ? BCM2711_DMA40_INC : 0); ++} ++ ++static inline uint32_t to_bcm2711_dsti(uint32_t info) ++{ ++ return ((info & BCM2835_DMA_D_INC) ? BCM2711_DMA40_INC : 0); ++} ++ ++static inline uint32_t to_bcm2711_cbaddr(dma_addr_t addr) ++{ ++ BUG_ON(addr & 0x1f); ++ return (addr >> 5); ++} ++ + static void bcm2835_dma_free_cb_chain(struct bcm2835_desc *desc) + { + size_t i; +@@ -225,45 +374,53 @@ static void bcm2835_dma_desc_free(struct + } + + static void bcm2835_dma_create_cb_set_length( +- struct bcm2835_chan *chan, ++ struct bcm2835_chan *c, + struct bcm2835_dma_cb *control_block, + size_t len, + size_t period_len, + size_t *total_len, + u32 finalextrainfo) + { +- size_t max_len = bcm2835_dma_max_frame_length(chan); ++ size_t max_len = bcm2835_dma_max_frame_length(c); ++ uint32_t cb_len; + + /* set the length taking lite-channel limitations into account */ +- control_block->length = min_t(u32, len, max_len); ++ cb_len = min_t(u32, len, max_len); + +- /* finished if we have no period_length */ +- if (!period_len) +- return; ++ if (period_len) { ++ /* ++ * period_len means: that we need to generate ++ * transfers that are terminating at every ++ * multiple of period_len - this is typically ++ * used to set the interrupt flag in info ++ * which is required during cyclic transfers ++ */ + +- /* +- * period_len means: that we need to generate +- * transfers that are terminating at every +- * multiple of period_len - this is typically +- * used to set the interrupt flag in info +- * which is required during cyclic transfers +- */ ++ /* have we filled in period_length yet? */ ++ if (*total_len + cb_len < period_len) { ++ /* update number of bytes in this period so far */ ++ *total_len += cb_len; ++ } else { ++ /* calculate the length that remains to reach period_len */ ++ cb_len = period_len - *total_len; + +- /* have we filled in period_length yet? */ +- if (*total_len + control_block->length < period_len) { +- /* update number of bytes in this period so far */ +- *total_len += control_block->length; +- return; ++ /* reset total_length for next period */ ++ *total_len = 0; ++ } + } + +- /* calculate the length that remains to reach period_length */ +- control_block->length = period_len - *total_len; +- +- /* reset total_length for next period */ +- *total_len = 0; +- +- /* add extrainfo bits in info */ +- control_block->info |= finalextrainfo; ++ if (c->is_40bit_channel) { ++ struct bcm2711_dma40_scb *scb = ++ (struct bcm2711_dma40_scb *)control_block; ++ ++ scb->len = cb_len; ++ /* add extrainfo bits to ti */ ++ scb->ti |= to_bcm2711_ti(finalextrainfo); ++ } else { ++ control_block->length = cb_len; ++ /* add extrainfo bits to info */ ++ control_block->info |= finalextrainfo; ++ } + } + + static inline size_t bcm2835_dma_count_frames_for_sg( +@@ -286,7 +443,7 @@ static inline size_t bcm2835_dma_count_f + /** + * bcm2835_dma_create_cb_chain - create a control block and fills data in + * +- * @chan: the @dma_chan for which we run this ++ * @c: the @bcm2835_chan for which we run this + * @direction: the direction in which we transfer + * @cyclic: it is a cyclic transfer + * @info: the default info bits to apply per controlblock +@@ -304,12 +461,11 @@ static inline size_t bcm2835_dma_count_f + * @gfp: the GFP flag to use for allocation + */ + static struct bcm2835_desc *bcm2835_dma_create_cb_chain( +- struct dma_chan *chan, enum dma_transfer_direction direction, ++ struct bcm2835_chan *c, enum dma_transfer_direction direction, + bool cyclic, u32 info, u32 finalextrainfo, size_t frames, + dma_addr_t src, dma_addr_t dst, size_t buf_len, + size_t period_len, gfp_t gfp) + { +- struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); + size_t len = buf_len, total_len; + size_t frame; + struct bcm2835_desc *d; +@@ -341,11 +497,23 @@ static struct bcm2835_desc *bcm2835_dma_ + + /* fill in the control block */ + control_block = cb_entry->cb; +- control_block->info = info; +- control_block->src = src; +- control_block->dst = dst; +- control_block->stride = 0; +- control_block->next = 0; ++ if (c->is_40bit_channel) { ++ struct bcm2711_dma40_scb *scb = ++ (struct bcm2711_dma40_scb *)control_block; ++ scb->ti = to_bcm2711_ti(info); ++ scb->src = lower_32_bits(src); ++ scb->srci= upper_32_bits(src) | to_bcm2711_srci(info); ++ scb->dst = lower_32_bits(dst); ++ scb->dsti = upper_32_bits(dst) | to_bcm2711_dsti(info); ++ scb->next_cb = 0; ++ } else { ++ control_block->info = info; ++ control_block->src = src; ++ control_block->dst = dst; ++ control_block->stride = 0; ++ control_block->next = 0; ++ } ++ + /* set up length in control_block if requested */ + if (buf_len) { + /* calculate length honoring period_length */ +@@ -359,7 +527,11 @@ static struct bcm2835_desc *bcm2835_dma_ + } + + /* link this the last controlblock */ +- if (frame) ++ if (frame && c->is_40bit_channel) ++ ((struct bcm2711_dma40_scb *) ++ d->cb_list[frame - 1].cb)->next_cb = ++ to_bcm2711_cbaddr(cb_entry->paddr); ++ if (frame && !c->is_40bit_channel) + d->cb_list[frame - 1].cb->next = cb_entry->paddr; + + /* update src and dst and length */ +@@ -369,11 +541,21 @@ static struct bcm2835_desc *bcm2835_dma_ + dst += control_block->length; + + /* Length of total transfer */ +- d->size += control_block->length; ++ if (c->is_40bit_channel) ++ d->size += ((struct bcm2711_dma40_scb *)control_block)->len; ++ else ++ d->size += control_block->length; + } + + /* the last frame requires extra flags */ +- d->cb_list[d->frames - 1].cb->info |= finalextrainfo; ++ if (c->is_40bit_channel) { ++ struct bcm2711_dma40_scb *scb = ++ (struct bcm2711_dma40_scb *)d->cb_list[d->frames-1].cb; ++ ++ scb->ti |= to_bcm2711_ti(finalextrainfo); ++ } else { ++ d->cb_list[d->frames - 1].cb->info |= finalextrainfo; ++ } + + /* detect a size missmatch */ + if (buf_len && (d->size != buf_len)) +@@ -387,13 +569,12 @@ error_cb: + } + + static void bcm2835_dma_fill_cb_chain_with_sg( +- struct dma_chan *chan, ++ struct bcm2835_chan *c, + enum dma_transfer_direction direction, + struct bcm2835_cb_entry *cb, + struct scatterlist *sgl, + unsigned int sg_len) + { +- struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); + size_t len, max_len; + unsigned int i; + dma_addr_t addr; +@@ -401,14 +582,35 @@ static void bcm2835_dma_fill_cb_chain_wi + + max_len = bcm2835_dma_max_frame_length(c); + for_each_sg(sgl, sgent, sg_len, i) { +- for (addr = sg_dma_address(sgent), len = sg_dma_len(sgent); +- len > 0; +- addr += cb->cb->length, len -= cb->cb->length, cb++) { +- if (direction == DMA_DEV_TO_MEM) +- cb->cb->dst = addr; +- else +- cb->cb->src = addr; +- cb->cb->length = min(len, max_len); ++ if (c->is_40bit_channel) { ++ struct bcm2711_dma40_scb *scb; ++ ++ for (addr = sg_dma_address(sgent), ++ len = sg_dma_len(sgent); ++ len > 0; ++ addr += scb->len, len -= scb->len, cb++) { ++ scb = (struct bcm2711_dma40_scb *)cb->cb; ++ if (direction == DMA_DEV_TO_MEM) { ++ scb->dst = lower_32_bits(addr); ++ scb->dsti = upper_32_bits(addr) | BCM2711_DMA40_INC; ++ } else { ++ scb->src = lower_32_bits(addr); ++ scb->srci = upper_32_bits(addr) | BCM2711_DMA40_INC; ++ } ++ scb->len = min(len, max_len); ++ } ++ } else { ++ for (addr = sg_dma_address(sgent), ++ len = sg_dma_len(sgent); ++ len > 0; ++ addr += cb->cb->length, len -= cb->cb->length, ++ cb++) { ++ if (direction == DMA_DEV_TO_MEM) ++ cb->cb->dst = addr; ++ else ++ cb->cb->src = addr; ++ cb->cb->length = min(len, max_len); ++ } + } + } + } +@@ -417,6 +619,10 @@ static void bcm2835_dma_abort(struct bcm + { + void __iomem *chan_base = c->chan_base; + long int timeout = 10000; ++ u32 wait_mask = BCM2835_DMA_WAITING_FOR_WRITES; ++ ++ if (c->is_40bit_channel) ++ wait_mask = BCM2711_DMA40_WAITING_FOR_WRITES; + + /* + * A zero control block address means the channel is idle. +@@ -429,8 +635,7 @@ static void bcm2835_dma_abort(struct bcm + writel(0, chan_base + BCM2835_DMA_CS); + + /* Wait for any current AXI transfer to complete */ +- while ((readl(chan_base + BCM2835_DMA_CS) & +- BCM2835_DMA_WAITING_FOR_WRITES) && --timeout) ++ while ((readl(chan_base + BCM2835_DMA_CS) & wait_mask) && --timeout) + cpu_relax(); + + /* Peripheral might be stuck and fail to signal AXI write responses */ +@@ -455,9 +660,16 @@ static void bcm2835_dma_start_desc(struc + + c->desc = d = to_bcm2835_dma_desc(&vd->tx); + +- writel(d->cb_list[0].paddr, c->chan_base + BCM2835_DMA_ADDR); +- writel(BCM2835_DMA_ACTIVE | BCM2835_DMA_CS_FLAGS(c->dreq), +- c->chan_base + BCM2835_DMA_CS); ++ if (c->is_40bit_channel) { ++ writel(to_bcm2711_cbaddr(d->cb_list[0].paddr), ++ c->chan_base + BCM2711_DMA40_CB); ++ writel(BCM2711_DMA40_ACTIVE | BCM2711_DMA40_CS_FLAGS(c->dreq), ++ c->chan_base + BCM2711_DMA40_CS); ++ } else { ++ writel(d->cb_list[0].paddr, c->chan_base + BCM2835_DMA_ADDR); ++ writel(BCM2835_DMA_ACTIVE | BCM2835_DMA_CS_FLAGS(c->dreq), ++ c->chan_base + BCM2835_DMA_CS); ++ } + } + + static irqreturn_t bcm2835_dma_callback(int irq, void *data) +@@ -484,8 +696,7 @@ static irqreturn_t bcm2835_dma_callback( + * if this IRQ handler is threaded.) If the channel is finished, it + * will remain idle despite the ACTIVE flag being set. + */ +- writel(BCM2835_DMA_INT | BCM2835_DMA_ACTIVE | +- BCM2835_DMA_CS_FLAGS(c->dreq), ++ writel(BCM2835_DMA_INT | BCM2835_DMA_ACTIVE, + c->chan_base + BCM2835_DMA_CS); + + d = c->desc; +@@ -588,9 +799,17 @@ static enum dma_status bcm2835_dma_tx_st + struct bcm2835_desc *d = c->desc; + dma_addr_t pos; + +- if (d->dir == DMA_MEM_TO_DEV) ++ if (d->dir == DMA_MEM_TO_DEV && c->is_40bit_channel) ++ pos = readl(c->chan_base + BCM2711_DMA40_SRC) + ++ ((readl(c->chan_base + BCM2711_DMA40_SRCI) & ++ 0xff) << 8); ++ else if (d->dir == DMA_MEM_TO_DEV && !c->is_40bit_channel) + pos = readl(c->chan_base + BCM2835_DMA_SOURCE_AD); +- else if (d->dir == DMA_DEV_TO_MEM) ++ else if (d->dir == DMA_DEV_TO_MEM && c->is_40bit_channel) ++ pos = readl(c->chan_base + BCM2711_DMA40_DEST) + ++ ((readl(c->chan_base + BCM2711_DMA40_DESTI) & ++ 0xff) << 8); ++ else if (d->dir == DMA_DEV_TO_MEM && !c->is_40bit_channel) + pos = readl(c->chan_base + BCM2835_DMA_DEST_AD); + else + pos = 0; +@@ -636,7 +855,7 @@ static struct dma_async_tx_descriptor *b + frames = bcm2835_dma_frames_for_length(len, max_len); + + /* allocate the CB chain - this also fills in the pointers */ +- d = bcm2835_dma_create_cb_chain(chan, DMA_MEM_TO_MEM, false, ++ d = bcm2835_dma_create_cb_chain(c, DMA_MEM_TO_MEM, false, + info, extra, frames, + src, dst, len, 0, GFP_KERNEL); + if (!d) +@@ -671,11 +890,21 @@ static struct dma_async_tx_descriptor *b + if (c->cfg.src_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES) + return NULL; + src = c->cfg.src_addr; ++ /* ++ * One would think it ought to be possible to get the physical ++ * to dma address mapping information from the dma-ranges DT ++ * property, but I've not found a way yet that doesn't involve ++ * open-coding the whole thing. ++ */ ++ if (c->is_40bit_channel) ++ src |= 0x400000000ull; + info |= BCM2835_DMA_S_DREQ | BCM2835_DMA_D_INC; + } else { + if (c->cfg.dst_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES) + return NULL; + dst = c->cfg.dst_addr; ++ if (c->is_40bit_channel) ++ dst |= 0x400000000ull; + info |= BCM2835_DMA_D_DREQ | BCM2835_DMA_S_INC; + } + +@@ -683,7 +912,7 @@ static struct dma_async_tx_descriptor *b + frames = bcm2835_dma_count_frames_for_sg(c, sgl, sg_len); + + /* allocate the CB chain */ +- d = bcm2835_dma_create_cb_chain(chan, direction, false, ++ d = bcm2835_dma_create_cb_chain(c, direction, false, + info, extra, + frames, src, dst, 0, 0, + GFP_NOWAIT); +@@ -691,7 +920,7 @@ static struct dma_async_tx_descriptor *b + return NULL; + + /* fill in frames with scatterlist pointers */ +- bcm2835_dma_fill_cb_chain_with_sg(chan, direction, d->cb_list, ++ bcm2835_dma_fill_cb_chain_with_sg(c, direction, d->cb_list, + sgl, sg_len); + + return vchan_tx_prep(&c->vc, &d->vd, flags); +@@ -745,12 +974,16 @@ static struct dma_async_tx_descriptor *b + if (c->cfg.src_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES) + return NULL; + src = c->cfg.src_addr; ++ if (c->is_40bit_channel) ++ src |= 0x400000000ull; + dst = buf_addr; + info |= BCM2835_DMA_S_DREQ | BCM2835_DMA_D_INC; + } else { + if (c->cfg.dst_addr_width != DMA_SLAVE_BUSWIDTH_4_BYTES) + return NULL; + dst = c->cfg.dst_addr; ++ if (c->is_40bit_channel) ++ dst |= 0x400000000ull; + src = buf_addr; + info |= BCM2835_DMA_D_DREQ | BCM2835_DMA_S_INC; + +@@ -770,7 +1003,7 @@ static struct dma_async_tx_descriptor *b + * note that we need to use GFP_NOWAIT, as the ALSA i2s dmaengine + * implementation calls prep_dma_cyclic with interrupts disabled. + */ +- d = bcm2835_dma_create_cb_chain(chan, direction, true, ++ d = bcm2835_dma_create_cb_chain(c, direction, true, + info, extra, + frames, src, dst, buf_len, + period_len, GFP_NOWAIT); +@@ -778,7 +1011,12 @@ static struct dma_async_tx_descriptor *b + return NULL; + + /* wrap around into a loop */ +- d->cb_list[d->frames - 1].cb->next = d->cb_list[0].paddr; ++ if (c->is_40bit_channel) ++ ((struct bcm2711_dma40_scb *) ++ d->cb_list[frames - 1].cb)->next_cb = ++ to_bcm2711_cbaddr(d->cb_list[0].paddr); ++ else ++ d->cb_list[d->frames - 1].cb->next = d->cb_list[0].paddr; + + return vchan_tx_prep(&c->vc, &d->vd, flags); + } +@@ -839,9 +1077,11 @@ static int bcm2835_dma_chan_init(struct + c->irq_number = irq; + c->irq_flags = irq_flags; + +- /* check in DEBUG register if this is a LITE channel */ +- if (readl(c->chan_base + BCM2835_DMA_DEBUG) & +- BCM2835_DMA_DEBUG_LITE) ++ /* check for 40bit and lite channels */ ++ if (d->cfg_data->chan_40bit_mask & BIT(chan_id)) ++ c->is_40bit_channel = true; ++ else if (readl(c->chan_base + BCM2835_DMA_DEBUG) & ++ BCM2835_DMA_DEBUG_LITE) + c->is_lite_channel = true; + + return 0; +@@ -861,8 +1101,58 @@ static void bcm2835_dma_free(struct bcm2 + DMA_TO_DEVICE, DMA_ATTR_SKIP_CPU_SYNC); + } + ++int bcm2711_dma40_memcpy_init(void) ++{ ++ if (!memcpy_parent) ++ return -EPROBE_DEFER; ++ ++ if (!memcpy_chan) ++ return -EINVAL; ++ ++ if (!memcpy_scb) ++ return -ENOMEM; ++ ++ return 0; ++} ++EXPORT_SYMBOL(bcm2711_dma40_memcpy_init); ++ ++void bcm2711_dma40_memcpy(dma_addr_t dst, dma_addr_t src, size_t size) ++{ ++ struct bcm2711_dma40_scb *scb = memcpy_scb; ++ unsigned long flags; ++ ++ if (!scb) { ++ pr_err("bcm2711_dma40_memcpy not initialised!\n"); ++ return; ++ } ++ ++ spin_lock_irqsave(&memcpy_lock, flags); ++ ++ scb->ti = 0; ++ scb->src = lower_32_bits(src); ++ scb->srci = upper_32_bits(src) | BCM2711_DMA40_MEMCPY_XFER_INFO; ++ scb->dst = lower_32_bits(dst); ++ scb->dsti = upper_32_bits(dst) | BCM2711_DMA40_MEMCPY_XFER_INFO; ++ scb->len = size; ++ scb->next_cb = 0; ++ ++ writel((u32)(memcpy_scb_dma >> 5), memcpy_chan + BCM2711_DMA40_CB); ++ writel(BCM2711_DMA40_MEMCPY_FLAGS + BCM2711_DMA40_ACTIVE, ++ memcpy_chan + BCM2711_DMA40_CS); ++ ++ /* Poll for completion */ ++ while (!(readl(memcpy_chan + BCM2711_DMA40_CS) & BCM2711_DMA40_END)) ++ cpu_relax(); ++ ++ writel(BCM2711_DMA40_END, memcpy_chan + BCM2711_DMA40_CS); ++ ++ spin_unlock_irqrestore(&memcpy_lock, flags); ++} ++EXPORT_SYMBOL(bcm2711_dma40_memcpy); ++ + static const struct of_device_id bcm2835_dma_of_match[] = { +- { .compatible = "brcm,bcm2835-dma", }, ++ { .compatible = "brcm,bcm2835-dma", .data = &bcm2835_dma_cfg }, ++ { .compatible = "brcm,bcm2711-dma", .data = &bcm2711_dma_cfg }, + {}, + }; + MODULE_DEVICE_TABLE(of, bcm2835_dma_of_match); +@@ -894,6 +1184,8 @@ static int bcm2835_dma_probe(struct plat + int irq_flags; + uint32_t chans_available; + char chan_name[BCM2835_DMA_CHAN_NAME_SIZE]; ++ const struct of_device_id *of_id; ++ int chan_count, chan_start, chan_end; + + if (!pdev->dev.dma_mask) + pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask; +@@ -914,9 +1206,13 @@ static int bcm2835_dma_probe(struct plat + base = devm_ioremap_resource(&pdev->dev, res); + if (IS_ERR(base)) + return PTR_ERR(base); +- rc = bcm_dmaman_probe(pdev, base, BCM2835_DMA_BULK_MASK); +- if (rc) +- dev_err(&pdev->dev, "Failed to initialize the legacy API\n"); ++ ++ /* The set of channels can be split across multiple instances. */ ++ chan_start = ((u32)(uintptr_t)base / BCM2835_DMA_CHAN_SIZE) & 0xf; ++ base -= BCM2835_DMA_CHAN(chan_start); ++ chan_count = resource_size(res) / BCM2835_DMA_CHAN_SIZE; ++ chan_end = min(chan_start + chan_count, ++ BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED + 1); + + od->base = base; + +@@ -953,6 +1249,14 @@ static int bcm2835_dma_probe(struct plat + return -ENOMEM; + } + ++ of_id = of_match_node(bcm2835_dma_of_match, pdev->dev.of_node); ++ if (!of_id) { ++ dev_err(&pdev->dev, "Failed to match compatible string\n"); ++ return -EINVAL; ++ } ++ ++ od->cfg_data = of_id->data; ++ + /* Request DMA channel mask from device tree */ + if (of_property_read_u32(pdev->dev.of_node, + "brcm,dma-channel-mask", +@@ -962,11 +1266,34 @@ static int bcm2835_dma_probe(struct plat + goto err_no_dma; + } + +- /* Channel 0 is used by the legacy API */ +- chans_available &= ~BCM2835_DMA_BULK_MASK; ++ /* One channel is reserved for the legacy API */ ++ if (chans_available & BCM2835_DMA_BULK_MASK) { ++ rc = bcm_dmaman_probe(pdev, base, ++ chans_available & BCM2835_DMA_BULK_MASK); ++ if (rc) ++ dev_err(&pdev->dev, ++ "Failed to initialize the legacy API\n"); ++ ++ chans_available &= ~BCM2835_DMA_BULK_MASK; ++ } ++ ++ /* And possibly one for the 40-bit DMA memcpy API */ ++ if (chans_available & od->cfg_data->chan_40bit_mask & ++ BIT(BCM2711_DMA_MEMCPY_CHAN)) { ++ memcpy_parent = od; ++ memcpy_chan = BCM2835_DMA_CHANIO(base, BCM2711_DMA_MEMCPY_CHAN); ++ memcpy_scb = dma_alloc_coherent(memcpy_parent->ddev.dev, ++ sizeof(*memcpy_scb), ++ &memcpy_scb_dma, GFP_KERNEL); ++ if (!memcpy_scb) ++ dev_warn(&pdev->dev, ++ "Failed to allocated memcpy scb\n"); ++ ++ chans_available &= ~BIT(BCM2711_DMA_MEMCPY_CHAN); ++ } + + /* get irqs for each channel that we support */ +- for (i = 0; i <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; i++) { ++ for (i = chan_start; i < chan_end; i++) { + /* skip masked out channels */ + if (!(chans_available & (1 << i))) { + irq[i] = -1; +@@ -989,13 +1316,17 @@ static int bcm2835_dma_probe(struct plat + irq[i] = platform_get_irq(pdev, i < 11 ? i : 11); + } + ++ chan_count = 0; ++ + /* get irqs for each channel */ +- for (i = 0; i <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; i++) { ++ for (i = chan_start; i < chan_end; i++) { + /* skip channels without irq */ + if (irq[i] < 0) + continue; + + /* check if there are other channels that also use this irq */ ++ /* FIXME: This will fail if interrupts are shared across ++ instances */ + irq_flags = 0; + for (j = 0; j <= BCM2835_DMA_MAX_DMA_CHAN_SUPPORTED; j++) + if ((i != j) && (irq[j] == irq[i])) { +@@ -1007,9 +1338,10 @@ static int bcm2835_dma_probe(struct plat + rc = bcm2835_dma_chan_init(od, i, irq[i], irq_flags); + if (rc) + goto err_no_dma; ++ chan_count++; + } + +- dev_dbg(&pdev->dev, "Initialized %i DMA channels\n", i); ++ dev_dbg(&pdev->dev, "Initialized %i DMA channels\n", chan_count); + + /* Device-tree DMA controller registration */ + rc = of_dma_controller_register(pdev->dev.of_node, +@@ -1041,6 +1373,13 @@ static int bcm2835_dma_remove(struct pla + + bcm_dmaman_remove(pdev); + dma_async_device_unregister(&od->ddev); ++ if (memcpy_parent == od) { ++ dma_free_coherent(&pdev->dev, sizeof(*memcpy_scb), memcpy_scb, ++ memcpy_scb_dma); ++ memcpy_parent = NULL; ++ memcpy_scb = NULL; ++ memcpy_chan = NULL; ++ } + bcm2835_dma_free(od); + + return 0; diff --git a/target/linux/bcm27xx/patches-5.10/950-0223-overlays-Make-the-i2c-gpio-overlay-safe-again.patch b/target/linux/bcm27xx/patches-5.10/950-0223-overlays-Make-the-i2c-gpio-overlay-safe-again.patch new file mode 100644 index 0000000000..589b583158 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0223-overlays-Make-the-i2c-gpio-overlay-safe-again.patch @@ -0,0 +1,32 @@ +From 4721459bb386bf32b2295b947f38b91cdd97929b Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 1 May 2020 17:56:13 +0100 +Subject: [PATCH] overlays: Make the i2c-gpio overlay safe again + +Like many overlays, the i2c-gpio overlay goes to efforts to avoid +generating warnings about #address-cells and #size-cells not +being defined, which it does by defining them. Unfortunately this +is fatal if they don't match what the system requires, and the +recent switch to #size-cells = 2 on 2711 made i2c-gpio very +dangerous. + +In the absence of the knowledge of a clean way to fix this, just delete +the declarations and suffer the warnings. + +Signed-off-by: Phil Elwell +--- + arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts | 3 --- + 1 file changed, 3 deletions(-) + +--- a/arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts ++++ b/arch/arm/boot/dts/overlays/i2c-gpio-overlay.dts +@@ -11,9 +11,6 @@ + target-path = "/"; + + __overlay__ { +- #address-cells = <1>; +- #size-cells = <0>; +- + i2c_gpio: i2c@0 { + reg = <0xffffffff>; + compatible = "i2c-gpio"; diff --git a/target/linux/bcm27xx/patches-5.10/950-0224-media-i2c-imx219-Declare-that-the-driver-can-create-.patch b/target/linux/bcm27xx/patches-5.10/950-0224-media-i2c-imx219-Declare-that-the-driver-can-create-.patch new file mode 100644 index 0000000000..87e1000617 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0224-media-i2c-imx219-Declare-that-the-driver-can-create-.patch @@ -0,0 +1,27 @@ +From 8a251d243fa3931f3b03677f4f58ceb728f42e99 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Mon, 20 Apr 2020 11:01:21 +0100 +Subject: [PATCH] media: i2c: imx219: Declare that the driver can + create events + +The flag V4L2_SUBDEV_FL_HAS_EVENTS is required if the subdev can +generate events. It can create events from the ctrl handler, therefore +this is required. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/imx219.c | 3 ++- + 1 file changed, 2 insertions(+), 1 deletion(-) + +--- a/drivers/media/i2c/imx219.c ++++ b/drivers/media/i2c/imx219.c +@@ -1591,7 +1591,8 @@ static int imx219_probe(struct i2c_clien + + /* Initialize subdev */ + imx219->sd.internal_ops = &imx219_internal_ops; +- imx219->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; ++ imx219->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | ++ V4L2_SUBDEV_FL_HAS_EVENTS; + imx219->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR; + + /* Initialize source pads */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0225-media-ov5647-Fix-return-codes-from-ov5647_write-ov56.patch b/target/linux/bcm27xx/patches-5.10/950-0225-media-ov5647-Fix-return-codes-from-ov5647_write-ov56.patch new file mode 100644 index 0000000000..19f24a33a6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0225-media-ov5647-Fix-return-codes-from-ov5647_write-ov56.patch @@ -0,0 +1,74 @@ +From 0a17f217911f989cd58df868f902b488088a1398 Mon Sep 17 00:00:00 2001 +From: David Plowman +Date: Wed, 15 Jan 2020 13:40:38 +0000 +Subject: [PATCH] media: ov5647: Fix return codes from + ov5647_write/ov5647_read functions. + +Previously they were returning positive non-zero codes for success, +which were getting passed up the call stack. Since release 4.19, +do_dentry_open (fs/open.c) has been catching these and flagging an +error. (So this driver has been broken since that date.) + +Fixes: 3c2472a [media] media: i2c: Add support for OV5647 sensor +Signed-off-by: David Plowman +Signed-off-by: Naushir Patuck +--- + drivers/media/i2c/ov5647.c | 30 +++++++++++++++++++++++++++--- + 1 file changed, 27 insertions(+), 3 deletions(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -214,9 +214,18 @@ static int ov5647_write(struct v4l2_subd + struct i2c_client *client = v4l2_get_subdevdata(sd); + + ret = i2c_master_send(client, data, 3); +- if (ret < 0) ++ /* ++ * Writing the wrong number of bytes also needs to be flagged as an ++ * error. Success needs to produce a 0 return code. ++ */ ++ if (ret == 3) { ++ ret = 0; ++ } else { + dev_dbg(&client->dev, "%s: i2c write error, reg: %x\n", + __func__, reg); ++ if (ret >= 0) ++ ret = -EINVAL; ++ } + + return ret; + } +@@ -228,16 +237,31 @@ static int ov5647_read(struct v4l2_subde + struct i2c_client *client = v4l2_get_subdevdata(sd); + + ret = i2c_master_send(client, data_w, 2); +- if (ret < 0) { ++ /* ++ * A negative return code, or sending the wrong number of bytes, both ++ * count as an error. ++ */ ++ if (ret != 2) { + dev_dbg(&client->dev, "%s: i2c write error, reg: %x\n", + __func__, reg); ++ if (ret >= 0) ++ ret = -EINVAL; + return ret; + } + + ret = i2c_master_recv(client, val, 1); +- if (ret < 0) ++ /* ++ * The only return value indicating success is 1. Anything else, even ++ * a non-negative value, indicates something went wrong. ++ */ ++ if (ret == 1) { ++ ret = 0; ++ } else { + dev_dbg(&client->dev, "%s: i2c read error, reg: %x\n", + __func__, reg); ++ if (ret >= 0) ++ ret = -EINVAL; ++ } + + return ret; + } diff --git a/target/linux/bcm27xx/patches-5.10/950-0226-media-ov5647-Add-basic-support-for-multiple-sensor-m.patch b/target/linux/bcm27xx/patches-5.10/950-0226-media-ov5647-Add-basic-support-for-multiple-sensor-m.patch new file mode 100644 index 0000000000..be41bb4a26 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0226-media-ov5647-Add-basic-support-for-multiple-sensor-m.patch @@ -0,0 +1,407 @@ +From c3535af52b9f641565db400aab050298b786fcf3 Mon Sep 17 00:00:00 2001 +From: David Plowman +Date: Wed, 29 Jan 2020 15:30:53 +0000 +Subject: [PATCH] media: ov5647: Add basic support for multiple sensor + modes. + +Specifically: + +Added a structure ov5647_mode and a list of supported_modes (though no +actual new modes as yet). The state object points to the "current mode". + +ov5647_enum_mbus_code, ov5647_enum_frame_size, ov5647_set_fmt and +ov5647_get_fmt all needed upgrading to cope with multiple modes. + +__sensor_init (which writes all the registers) is now called by +ov5647_stream_on (once the mode is known) rather than by +ov5647_sensor_power. + +Signed-off-by: David Plowman +Signed-off-by: Naushir Patuck +--- + drivers/media/i2c/ov5647.c | 268 ++++++++++++++++++++++++++++--------- + 1 file changed, 202 insertions(+), 66 deletions(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -86,13 +86,17 @@ struct regval_list { + u8 data; + }; + ++struct ov5647_mode { ++ struct v4l2_mbus_framefmt format; ++ struct regval_list *reg_list; ++ unsigned int num_regs; ++}; ++ + struct ov5647 { + struct v4l2_subdev sd; + struct media_pad pad; + struct mutex lock; +- struct v4l2_mbus_framefmt format; +- unsigned int width; +- unsigned int height; ++ const struct ov5647_mode *mode; + int power_count; + struct clk *xclk; + struct gpio_desc *pwdn; +@@ -207,6 +211,32 @@ static struct regval_list ov5647_640x480 + {0x0100, 0x01}, + }; + ++static struct ov5647_mode supported_modes_8bit[] = { ++ /* ++ * Original 8-bit VGA mode ++ * Uncentred crop (top left quarter) from 2x2 binned 1296x972 image. ++ */ ++ { ++ { ++ .code = MEDIA_BUS_FMT_SBGGR8_1X8, ++ .colorspace = V4L2_COLORSPACE_SRGB, ++ .field = V4L2_FIELD_NONE, ++ .width = 640, ++ .height = 480 ++ }, ++ ov5647_640x480, ++ ARRAY_SIZE(ov5647_640x480) ++ }, ++ /* more modes below here... */ ++}; ++ ++static struct ov5647_mode supported_modes_10bit[] = { ++ /* no 10-bit modes yet */ ++}; ++ ++/* Use original 8-bit VGA mode as default. */ ++#define OV5647_DEFAULT_MODE (&supported_modes_8bit[0]) ++ + static int ov5647_write(struct v4l2_subdev *sd, u16 reg, u8 val) + { + int ret; +@@ -293,12 +323,55 @@ static int ov5647_set_virtual_channel(st + return ov5647_write(sd, OV5647_REG_MIPI_CTRL14, channel_id | (channel << 6)); + } + ++static int __sensor_init(struct v4l2_subdev *sd) ++{ ++ int ret; ++ u8 resetval, rdval; ++ struct i2c_client *client = v4l2_get_subdevdata(sd); ++ struct ov5647 *state = to_state(sd); ++ ++ ret = ov5647_read(sd, OV5647_SW_STANDBY, &rdval); ++ if (ret < 0) ++ return ret; ++ ++ ret = ov5647_write_array(sd, state->mode->reg_list, ++ state->mode->num_regs); ++ if (ret < 0) { ++ dev_err(&client->dev, "write sensor default regs error\n"); ++ return ret; ++ } ++ ++ ret = ov5647_set_virtual_channel(sd, 0); ++ if (ret < 0) ++ return ret; ++ ++ ret = ov5647_read(sd, OV5647_SW_STANDBY, &resetval); ++ if (ret < 0) ++ return ret; ++ ++ if (!(resetval & 0x01)) { ++ dev_err(&client->dev, "Device was in SW standby"); ++ ret = ov5647_write(sd, OV5647_SW_STANDBY, 0x01); ++ if (ret < 0) ++ return ret; ++ } ++ ++ return 0; ++} ++ + static int ov5647_stream_on(struct v4l2_subdev *sd) + { ++ struct i2c_client *client = v4l2_get_subdevdata(sd); + struct ov5647 *ov5647 = to_state(sd); + u8 val = MIPI_CTRL00_BUS_IDLE; + int ret; + ++ ret = __sensor_init(sd); ++ if (ret < 0) { ++ dev_err(&client->dev, "sensor_init failed\n"); ++ return ret; ++ } ++ + if (ov5647->flags & V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK) + val |= MIPI_CTRL00_CLOCK_LANE_GATE | + MIPI_CTRL00_LINE_SYNC_ENABLE; +@@ -347,44 +420,6 @@ static int set_sw_standby(struct v4l2_su + return ov5647_write(sd, OV5647_SW_STANDBY, rdval); + } + +-static int __sensor_init(struct v4l2_subdev *sd) +-{ +- int ret; +- u8 resetval, rdval; +- struct i2c_client *client = v4l2_get_subdevdata(sd); +- +- ret = ov5647_read(sd, OV5647_SW_STANDBY, &rdval); +- if (ret < 0) +- return ret; +- +- ret = ov5647_write_array(sd, ov5647_640x480, +- ARRAY_SIZE(ov5647_640x480)); +- if (ret < 0) { +- dev_err(&client->dev, "write sensor default regs error\n"); +- return ret; +- } +- +- ret = ov5647_set_virtual_channel(sd, 0); +- if (ret < 0) +- return ret; +- +- ret = ov5647_read(sd, OV5647_SW_STANDBY, &resetval); +- if (ret < 0) +- return ret; +- +- if (!(resetval & 0x01)) { +- dev_err(&client->dev, "Device was in SW standby"); +- ret = ov5647_write(sd, OV5647_SW_STANDBY, 0x01); +- if (ret < 0) +- return ret; +- } +- +- /* +- * stream off to make the clock lane into LP-11 state. +- */ +- return ov5647_stream_off(sd); +-} +- + static int ov5647_sensor_power(struct v4l2_subdev *sd, int on) + { + int ret = 0; +@@ -408,7 +443,7 @@ static int ov5647_sensor_power(struct v4 + } + + ret = ov5647_write_array(sd, sensor_oe_enable_regs, +- ARRAY_SIZE(sensor_oe_enable_regs)); ++ ARRAY_SIZE(sensor_oe_enable_regs)); + if (ret < 0) { + clk_disable_unprepare(ov5647->xclk); + dev_err(&client->dev, +@@ -416,7 +451,10 @@ static int ov5647_sensor_power(struct v4 + goto out; + } + +- ret = __sensor_init(sd); ++ /* ++ * Ensure streaming off to make clock lane go into LP-11 state. ++ */ ++ ret = ov5647_stream_off(sd); + if (ret < 0) { + clk_disable_unprepare(ov5647->xclk); + dev_err(&client->dev, +@@ -427,7 +465,7 @@ static int ov5647_sensor_power(struct v4 + dev_dbg(&client->dev, "OV5647 power off\n"); + + ret = ov5647_write_array(sd, sensor_oe_disable_regs, +- ARRAY_SIZE(sensor_oe_disable_regs)); ++ ARRAY_SIZE(sensor_oe_disable_regs)); + + if (ret < 0) + dev_dbg(&client->dev, "disable oe failed\n"); +@@ -489,10 +527,19 @@ static const struct v4l2_subdev_core_ops + + static int ov5647_s_stream(struct v4l2_subdev *sd, int enable) + { ++ struct ov5647 *state = to_state(sd); ++ int ret = 0; ++ ++ mutex_lock(&state->lock); ++ + if (enable) +- return ov5647_stream_on(sd); ++ ret = ov5647_stream_on(sd); + else +- return ov5647_stream_off(sd); ++ ret = ov5647_stream_off(sd); ++ ++ mutex_unlock(&state->lock); ++ ++ return ret; + } + + static const struct v4l2_subdev_video_ops ov5647_subdev_video_ops = { +@@ -503,38 +550,127 @@ static int ov5647_enum_mbus_code(struct + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_mbus_code_enum *code) + { +- if (code->index > 0) ++ if (code->index == 0 && ARRAY_SIZE(supported_modes_8bit)) ++ code->code = MEDIA_BUS_FMT_SBGGR8_1X8; ++ else if (code->index == 0 && ARRAY_SIZE(supported_modes_8bit) == 0 && ++ ARRAY_SIZE(supported_modes_10bit)) ++ code->code = MEDIA_BUS_FMT_SBGGR10_1X10; ++ else if (code->index == 1 && ARRAY_SIZE(supported_modes_8bit) && ++ ARRAY_SIZE(supported_modes_10bit)) ++ code->code = MEDIA_BUS_FMT_SBGGR10_1X10; ++ else + return -EINVAL; + +- code->code = MEDIA_BUS_FMT_SBGGR8_1X8; ++ return 0; ++} ++ ++static int ov5647_enum_frame_size(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_frame_size_enum *fse) ++{ ++ struct ov5647_mode *mode = NULL; ++ ++ if (fse->code == MEDIA_BUS_FMT_SBGGR8_1X8) { ++ if (fse->index >= ARRAY_SIZE(supported_modes_8bit)) ++ return -EINVAL; ++ mode = &supported_modes_8bit[fse->index]; ++ } else if (fse->code == MEDIA_BUS_FMT_SBGGR10_1X10) { ++ if (fse->index >= ARRAY_SIZE(supported_modes_10bit)) ++ return -EINVAL; ++ mode = &supported_modes_10bit[fse->index]; ++ } else { ++ return -EINVAL; ++ } ++ ++ fse->min_width = mode->format.width; ++ fse->max_width = fse->min_width; ++ fse->min_height = mode->format.height; ++ fse->max_height = fse->min_height; ++ ++ return 0; ++} ++ ++static int ov5647_set_fmt(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_format *format) ++{ ++ struct v4l2_mbus_framefmt *fmt = &format->format; ++ struct ov5647 *state = to_state(sd); ++ struct v4l2_mbus_framefmt *framefmt; ++ const struct ov5647_mode *mode_8bit, *mode_10bit, *mode = NULL; ++ ++ if (format->pad != 0) ++ return -EINVAL; ++ ++ mutex_lock(&state->lock); ++ ++ /* ++ * Try to respect any given pixel format, otherwise try for a 10-bit ++ * mode. ++ */ ++ mode_8bit = v4l2_find_nearest_size(supported_modes_8bit, ++ ARRAY_SIZE(supported_modes_8bit), ++ format.width, format.height, ++ format->format.width, ++ format->format.height); ++ mode_10bit = v4l2_find_nearest_size(supported_modes_10bit, ++ ARRAY_SIZE(supported_modes_10bit), ++ format.width, format.height, ++ format->format.width, ++ format->format.height); ++ if (format->format.code == MEDIA_BUS_FMT_SBGGR8_1X8 && mode_8bit) ++ mode = mode_8bit; ++ else if (format->format.code == MEDIA_BUS_FMT_SBGGR10_1X10 && ++ mode_10bit) ++ mode = mode_10bit; ++ else if (mode_10bit) ++ mode = mode_10bit; ++ else ++ mode = mode_8bit; ++ ++ if (!mode) ++ return -EINVAL; ++ ++ *fmt = mode->format; ++ if (format->which == V4L2_SUBDEV_FORMAT_TRY) { ++ framefmt = v4l2_subdev_get_try_format(sd, cfg, format->pad); ++ *framefmt = format->format; ++ } else { ++ state->mode = mode; ++ } ++ ++ mutex_unlock(&state->lock); + + return 0; + } + +-static int ov5647_set_get_fmt(struct v4l2_subdev *sd, +- struct v4l2_subdev_pad_config *cfg, +- struct v4l2_subdev_format *format) ++static int ov5647_get_fmt(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_format *format) + { + struct v4l2_mbus_framefmt *fmt = &format->format; ++ struct ov5647 *state = to_state(sd); + + if (format->pad != 0) + return -EINVAL; + +- /* Only one format is supported, so return that */ +- memset(fmt, 0, sizeof(*fmt)); +- fmt->code = MEDIA_BUS_FMT_SBGGR8_1X8; +- fmt->colorspace = V4L2_COLORSPACE_SRGB; +- fmt->field = V4L2_FIELD_NONE; +- fmt->width = 640; +- fmt->height = 480; ++ mutex_lock(&state->lock); ++ ++ if (format->which == V4L2_SUBDEV_FORMAT_TRY) ++ *fmt = *v4l2_subdev_get_try_format(sd, cfg, format->pad); ++ else ++ *fmt = state->mode->format; ++ ++ mutex_unlock(&state->lock); + + return 0; + } + + static const struct v4l2_subdev_pad_ops ov5647_subdev_pad_ops = { + .enum_mbus_code = ov5647_enum_mbus_code, +- .set_fmt = ov5647_set_get_fmt, +- .get_fmt = ov5647_set_get_fmt, ++ .set_fmt = ov5647_set_fmt, ++ .get_fmt = ov5647_get_fmt, ++ .enum_frame_size = ov5647_enum_frame_size, + }; + + static const struct v4l2_subdev_ops ov5647_subdev_ops = { +@@ -580,18 +716,15 @@ static int ov5647_open(struct v4l2_subde + v4l2_subdev_get_try_format(sd, fh->pad, 0); + struct v4l2_rect *crop = + v4l2_subdev_get_try_crop(sd, fh->pad, 0); ++ struct ov5647 *state = to_state(sd); + + crop->left = OV5647_COLUMN_START_DEF; + crop->top = OV5647_ROW_START_DEF; + crop->width = OV5647_WINDOW_WIDTH_DEF; + crop->height = OV5647_WINDOW_HEIGHT_DEF; + +- format->code = MEDIA_BUS_FMT_SBGGR8_1X8; +- +- format->width = OV5647_WINDOW_WIDTH_DEF; +- format->height = OV5647_WINDOW_HEIGHT_DEF; +- format->field = V4L2_FIELD_NONE; +- format->colorspace = V4L2_COLORSPACE_SRGB; ++ /* Set the default format to the same as the sensor. */ ++ *format = state->mode->format; + + return 0; + } +@@ -660,6 +793,9 @@ static int ov5647_probe(struct i2c_clien + + mutex_init(&sensor->lock); + ++ /* Set the default mode before we init the subdev */ ++ sensor->mode = OV5647_DEFAULT_MODE; ++ + sd = &sensor->sd; + v4l2_i2c_subdev_init(sd, client, &ov5647_subdev_ops); + sensor->sd.internal_ops = &ov5647_subdev_internal_ops; diff --git a/target/linux/bcm27xx/patches-5.10/950-0227-media-ov5647-Add-V4L2-controls-for-analogue-gain-exp.patch b/target/linux/bcm27xx/patches-5.10/950-0227-media-ov5647-Add-V4L2-controls-for-analogue-gain-exp.patch new file mode 100644 index 0000000000..583edace3a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0227-media-ov5647-Add-V4L2-controls-for-analogue-gain-exp.patch @@ -0,0 +1,277 @@ +From 0c212ccaa2e790de8eb43b2766767f2713f93915 Mon Sep 17 00:00:00 2001 +From: David Plowman +Date: Wed, 29 Jan 2020 15:31:23 +0000 +Subject: [PATCH] media: ov5647: Add V4L2 controls for analogue gain, + exposure and AWB + +Added basic v4l2_ctrl_handler infrastructure (there was none +previously). + +Added controls to let AWB/AEC/AGC run in the sensor's auto mode or +manually. Also controls to set exposure (in lines) and analogue gain +(as a register code) from user code. + +Also delete registers (just the one) from the VGA mode register set +that are now controlled by the new V4L2 controls. + +Signed-off-by: David Plowman +Signed-off-by: Naushir Patuck +--- + drivers/media/i2c/ov5647.c | 175 ++++++++++++++++++++++++++++++++++++- + 1 file changed, 174 insertions(+), 1 deletion(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -29,11 +29,13 @@ + #include + #include + #include ++#include + #include + #include + #include + #include + ++ + #define SENSOR_NAME "ov5647" + + /* +@@ -53,9 +55,16 @@ + #define OV5647_REG_CHIPID_H 0x300A + #define OV5647_REG_CHIPID_L 0x300B + #define OV5640_REG_PAD_OUT 0x300D ++#define OV5647_REG_EXP_HI 0x3500 ++#define OV5647_REG_EXP_MID 0x3501 ++#define OV5647_REG_EXP_LO 0x3502 ++#define OV5647_REG_AEC_AGC 0x3503 ++#define OV5647_REG_GAIN_HI 0x350A ++#define OV5647_REG_GAIN_LO 0x350B + #define OV5647_REG_FRAME_OFF_NUMBER 0x4202 + #define OV5647_REG_MIPI_CTRL00 0x4800 + #define OV5647_REG_MIPI_CTRL14 0x4814 ++#define OV5647_REG_AWB 0x5001 + + #define REG_TERM 0xfffe + #define VAL_TERM 0xfe +@@ -101,6 +110,7 @@ struct ov5647 { + struct clk *xclk; + struct gpio_desc *pwdn; + unsigned int flags; ++ struct v4l2_ctrl_handler ctrls; + }; + + static inline struct ov5647 *to_state(struct v4l2_subdev *sd) +@@ -135,7 +145,6 @@ static struct regval_list ov5647_640x480 + {0x3612, 0x59}, + {0x3618, 0x00}, + {0x5000, 0x06}, +- {0x5001, 0x01}, + {0x5002, 0x41}, + {0x5003, 0x08}, + {0x5a00, 0x08}, +@@ -372,6 +381,11 @@ static int ov5647_stream_on(struct v4l2_ + return ret; + } + ++ /* Apply customized values from user when stream starts */ ++ ret = __v4l2_ctrl_handler_setup(sd->ctrl_handler); ++ if (ret) ++ return ret; ++ + if (ov5647->flags & V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK) + val |= MIPI_CTRL00_CLOCK_LANE_GATE | + MIPI_CTRL00_LINE_SYNC_ENABLE; +@@ -753,6 +767,120 @@ static int ov5647_parse_dt(struct device + return ret; + } + ++static int ov5647_s_auto_white_balance(struct v4l2_subdev *sd, u32 val) ++{ ++ /* non-zero turns on AWB */ ++ return ov5647_write(sd, OV5647_REG_AWB, val ? 1 : 0); ++} ++ ++static int ov5647_s_autogain(struct v4l2_subdev *sd, u32 val) ++{ ++ int ret; ++ u8 reg; ++ ++ /* non-zero turns on AGC by clearing bit 1 */ ++ ret = ov5647_read(sd, OV5647_REG_AEC_AGC, ®); ++ if (ret == 0) ++ ret = ov5647_write(sd, OV5647_REG_AEC_AGC, ++ val ? reg & ~2 : reg | 2); ++ ++ return ret; ++} ++ ++static int ov5647_s_exposure_auto(struct v4l2_subdev *sd, u32 val) ++{ ++ int ret; ++ u8 reg; ++ ++ /* Everything except V4L2_EXPOSURE_MANUAL turns on AEC by ++ * clearing bit 0 ++ */ ++ ret = ov5647_read(sd, OV5647_REG_AEC_AGC, ®); ++ if (ret == 0) ++ ret = ov5647_write(sd, OV5647_REG_AEC_AGC, ++ val == V4L2_EXPOSURE_MANUAL ? ++ reg | 1 : reg & ~1); ++ ++ return ret; ++} ++ ++static int ov5647_s_analogue_gain(struct v4l2_subdev *sd, u32 val) ++{ ++ int ret; ++ ++ /* 10 bits of gain, 2 in the high register */ ++ ret = ov5647_write(sd, OV5647_REG_GAIN_HI, (val >> 8) & 3); ++ if (ret == 0) ++ ret = ov5647_write(sd, OV5647_REG_GAIN_LO, val & 0xff); ++ ++ return ret; ++} ++ ++static int ov5647_s_exposure(struct v4l2_subdev *sd, u32 val) ++{ ++ int ret; ++ ++ /* Sensor has 20 bits, but the bottom 4 bits are fractions of a line ++ * which we leave as zero (and don't receive in "val"). ++ */ ++ ret = ov5647_write(sd, OV5647_REG_EXP_HI, (val >> 12) & 0xf); ++ if (ret == 0) ++ ov5647_write(sd, OV5647_REG_EXP_MID, (val >> 4) & 0xff); ++ if (ret == 0) ++ ov5647_write(sd, OV5647_REG_EXP_LO, (val & 0xf) << 4); ++ ++ return ret; ++} ++ ++static int ov5647_s_ctrl(struct v4l2_ctrl *ctrl) ++{ ++ struct ov5647 *state = container_of(ctrl->handler, ++ struct ov5647, ctrls); ++ struct v4l2_subdev *sd = &state->sd; ++ struct i2c_client *client = v4l2_get_subdevdata(sd); ++ int ret = 0; ++ ++ /* v4l2_ctrl_lock() locks our own mutex */ ++ ++ /* ++ * If the device is not powered up by the host driver do ++ * not apply any controls to H/W at this time. Instead ++ * the controls will be restored right after power-up. ++ */ ++ if (state->power_count == 0) ++ return 0; ++ ++ switch (ctrl->id) { ++ case V4L2_CID_AUTO_WHITE_BALANCE: ++ ret = ov5647_s_auto_white_balance(sd, ctrl->val); ++ break; ++ case V4L2_CID_AUTOGAIN: ++ ret = ov5647_s_autogain(sd, ctrl->val); ++ break; ++ case V4L2_CID_EXPOSURE_AUTO: ++ ret = ov5647_s_exposure_auto(sd, ctrl->val); ++ break; ++ case V4L2_CID_ANALOGUE_GAIN: ++ ret = ov5647_s_analogue_gain(sd, ctrl->val); ++ break; ++ case V4L2_CID_EXPOSURE: ++ ret = ov5647_s_exposure(sd, ctrl->val); ++ break; ++ default: ++ dev_info(&client->dev, ++ "ctrl(id:0x%x,val:0x%x) is not handled\n", ++ ctrl->id, ctrl->val); ++ ret = -EINVAL; ++ break; ++ } ++ ++ return ret; ++} ++ ++static const struct v4l2_ctrl_ops ov5647_ctrl_ops = { ++ .s_ctrl = ov5647_s_ctrl, ++}; ++ + static int ov5647_probe(struct i2c_client *client) + { + struct device *dev = &client->dev; +@@ -761,6 +889,7 @@ static int ov5647_probe(struct i2c_clien + struct v4l2_subdev *sd; + struct device_node *np = client->dev.of_node; + u32 xclk_freq; ++ struct v4l2_ctrl *ctrl; + + sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL); + if (!sensor) +@@ -793,6 +922,48 @@ static int ov5647_probe(struct i2c_clien + + mutex_init(&sensor->lock); + ++ /* Initialise controls. */ ++ v4l2_ctrl_handler_init(&sensor->ctrls, 3); ++ v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, ++ V4L2_CID_AUTOGAIN, ++ 0, /* min */ ++ 1, /* max */ ++ 1, /* step */ ++ 1); /* default */ ++ v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, ++ V4L2_CID_AUTO_WHITE_BALANCE, ++ 0, /* min */ ++ 1, /* max */ ++ 1, /* step */ ++ 1); /* default */ ++ v4l2_ctrl_new_std_menu(&sensor->ctrls, &ov5647_ctrl_ops, ++ V4L2_CID_EXPOSURE_AUTO, ++ V4L2_EXPOSURE_MANUAL, /* max */ ++ 0, /* skip_mask */ ++ V4L2_EXPOSURE_AUTO); /* default */ ++ ctrl = v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, ++ V4L2_CID_EXPOSURE, ++ 4, /* min lines */ ++ 65535, /* max lines (4+8+4 bits)*/ ++ 1, /* step */ ++ 1000); /* default number of lines */ ++ ctrl->flags |= V4L2_CTRL_FLAG_EXECUTE_ON_WRITE; ++ ctrl = v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, ++ V4L2_CID_ANALOGUE_GAIN, ++ 16, /* min, 16 = 1.0x */ ++ 1023, /* max (10 bits) */ ++ 1, /* step */ ++ 32); /* default, 32 = 2.0x */ ++ ctrl->flags |= V4L2_CTRL_FLAG_EXECUTE_ON_WRITE; ++ ++ if (sensor->ctrls.error) { ++ ret = sensor->ctrls.error; ++ dev_err(&client->dev, "%s control init failed (%d)\n", ++ __func__, ret); ++ goto error; ++ } ++ sensor->sd.ctrl_handler = &sensor->ctrls; ++ + /* Set the default mode before we init the subdev */ + sensor->mode = OV5647_DEFAULT_MODE; + +@@ -828,6 +999,7 @@ static int ov5647_probe(struct i2c_clien + error: + media_entity_cleanup(&sd->entity); + mutex_remove: ++ v4l2_ctrl_handler_free(&sensor->ctrls); + mutex_destroy(&sensor->lock); + return ret; + } +@@ -839,6 +1011,7 @@ static int ov5647_remove(struct i2c_clie + + v4l2_async_unregister_subdev(&ov5647->sd); + media_entity_cleanup(&ov5647->sd.entity); ++ v4l2_ctrl_handler_free(&ov5647->ctrls); + v4l2_device_unregister_subdev(sd); + mutex_destroy(&ov5647->lock); + diff --git a/target/linux/bcm27xx/patches-5.10/950-0228-media-ov5647-Add-extra-10-bit-sensor-modes.patch b/target/linux/bcm27xx/patches-5.10/950-0228-media-ov5647-Add-extra-10-bit-sensor-modes.patch new file mode 100644 index 0000000000..32b2375a48 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0228-media-ov5647-Add-extra-10-bit-sensor-modes.patch @@ -0,0 +1,549 @@ +From 004f4065edbb817a54121937514eb94159ecce69 Mon Sep 17 00:00:00 2001 +From: David Plowman +Date: Wed, 29 Jan 2020 15:31:28 +0000 +Subject: [PATCH] media: ov5647: Add extra 10-bit sensor modes. + +The 8-bit VGA mode remains, we add the following 10-bit modes: + +Mode 0: 2592x1944 full resolution. + +Mode 1: 1920x1080 full resolution, but centre-cropped. +(This mode achieves 30fps, mode 0 does not.) + +Mode 2: 1296x972 full field-of-view 2x2 binned mode. + +Mode 3: VGA full field of view mode. + +Signed-off-by: David Plowman +Signed-off-by: Naushir Patuck +--- + drivers/media/i2c/ov5647.c | 463 ++++++++++++++++++++++++++++++++++++- + 1 file changed, 452 insertions(+), 11 deletions(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -111,6 +111,7 @@ struct ov5647 { + struct gpio_desc *pwdn; + unsigned int flags; + struct v4l2_ctrl_handler ctrls; ++ bool write_mode_regs; + }; + + static inline struct ov5647 *to_state(struct v4l2_subdev *sd) +@@ -130,7 +131,7 @@ static struct regval_list sensor_oe_enab + {0x3002, 0xe4}, + }; + +-static struct regval_list ov5647_640x480[] = { ++static struct regval_list ov5647_640x480_8bit[] = { + {0x0100, 0x00}, + {0x0103, 0x01}, + {0x3034, 0x08}, +@@ -220,9 +221,378 @@ static struct regval_list ov5647_640x480 + {0x0100, 0x01}, + }; + ++static struct regval_list ov5647_2592x1944_10bit[] = { ++ {0x0100, 0x00}, ++ {0x0103, 0x01}, ++ {0x3034, 0x1a}, ++ {0x3035, 0x21}, ++ {0x3036, 0x69}, ++ {0x303c, 0x11}, ++ {0x3106, 0xf5}, ++ {0x3821, 0x06}, ++ {0x3820, 0x00}, ++ {0x3827, 0xec}, ++ {0x370c, 0x03}, ++ {0x3612, 0x5b}, ++ {0x3618, 0x04}, ++ {0x5000, 0x06}, ++ {0x5002, 0x41}, ++ {0x5003, 0x08}, ++ {0x5a00, 0x08}, ++ {0x3000, 0x00}, ++ {0x3001, 0x00}, ++ {0x3002, 0x00}, ++ {0x3016, 0x08}, ++ {0x3017, 0xe0}, ++ {0x3018, 0x44}, ++ {0x301c, 0xf8}, ++ {0x301d, 0xf0}, ++ {0x3a18, 0x00}, ++ {0x3a19, 0xf8}, ++ {0x3c01, 0x80}, ++ {0x3b07, 0x0c}, ++ {0x380c, 0x0b}, ++ {0x380d, 0x1c}, ++ {0x380e, 0x07}, ++ {0x380f, 0xb0}, ++ {0x3814, 0x11}, ++ {0x3815, 0x11}, ++ {0x3708, 0x64}, ++ {0x3709, 0x12}, ++ {0x3808, 0x0a}, ++ {0x3809, 0x20}, ++ {0x380a, 0x07}, ++ {0x380b, 0x98}, ++ {0x3800, 0x00}, ++ {0x3801, 0x00}, ++ {0x3802, 0x00}, ++ {0x3803, 0x00}, ++ {0x3804, 0x0a}, ++ {0x3805, 0x3f}, ++ {0x3806, 0x07}, ++ {0x3807, 0xa3}, ++ {0x3811, 0x10}, ++ {0x3813, 0x06}, ++ {0x3630, 0x2e}, ++ {0x3632, 0xe2}, ++ {0x3633, 0x23}, ++ {0x3634, 0x44}, ++ {0x3636, 0x06}, ++ {0x3620, 0x64}, ++ {0x3621, 0xe0}, ++ {0x3600, 0x37}, ++ {0x3704, 0xa0}, ++ {0x3703, 0x5a}, ++ {0x3715, 0x78}, ++ {0x3717, 0x01}, ++ {0x3731, 0x02}, ++ {0x370b, 0x60}, ++ {0x3705, 0x1a}, ++ {0x3f05, 0x02}, ++ {0x3f06, 0x10}, ++ {0x3f01, 0x0a}, ++ {0x3a08, 0x01}, ++ {0x3a09, 0x28}, ++ {0x3a0a, 0x00}, ++ {0x3a0b, 0xf6}, ++ {0x3a0d, 0x08}, ++ {0x3a0e, 0x06}, ++ {0x3a0f, 0x58}, ++ {0x3a10, 0x50}, ++ {0x3a1b, 0x58}, ++ {0x3a1e, 0x50}, ++ {0x3a11, 0x60}, ++ {0x3a1f, 0x28}, ++ {0x4001, 0x02}, ++ {0x4004, 0x04}, ++ {0x4000, 0x09}, ++ {0x4837, 0x19}, ++ {0x4800, 0x24}, ++ {0x3503, 0x03}, ++ {0x0100, 0x01}, ++}; ++ ++static struct regval_list ov5647_1080p30_10bit[] = { ++ {0x0100, 0x00}, ++ {0x0103, 0x01}, ++ {0x3034, 0x1a}, ++ {0x3035, 0x21}, ++ {0x3036, 0x62}, ++ {0x303c, 0x11}, ++ {0x3106, 0xf5}, ++ {0x3821, 0x06}, ++ {0x3820, 0x00}, ++ {0x3827, 0xec}, ++ {0x370c, 0x03}, ++ {0x3612, 0x5b}, ++ {0x3618, 0x04}, ++ {0x5000, 0x06}, ++ {0x5002, 0x41}, ++ {0x5003, 0x08}, ++ {0x5a00, 0x08}, ++ {0x3000, 0x00}, ++ {0x3001, 0x00}, ++ {0x3002, 0x00}, ++ {0x3016, 0x08}, ++ {0x3017, 0xe0}, ++ {0x3018, 0x44}, ++ {0x301c, 0xf8}, ++ {0x301d, 0xf0}, ++ {0x3a18, 0x00}, ++ {0x3a19, 0xf8}, ++ {0x3c01, 0x80}, ++ {0x3b07, 0x0c}, ++ {0x380c, 0x09}, ++ {0x380d, 0x70}, ++ {0x380e, 0x04}, ++ {0x380f, 0x50}, ++ {0x3814, 0x11}, ++ {0x3815, 0x11}, ++ {0x3708, 0x64}, ++ {0x3709, 0x12}, ++ {0x3808, 0x07}, ++ {0x3809, 0x80}, ++ {0x380a, 0x04}, ++ {0x380b, 0x38}, ++ {0x3800, 0x01}, ++ {0x3801, 0x5c}, ++ {0x3802, 0x01}, ++ {0x3803, 0xb2}, ++ {0x3804, 0x08}, ++ {0x3805, 0xe3}, ++ {0x3806, 0x05}, ++ {0x3807, 0xf1}, ++ {0x3811, 0x04}, ++ {0x3813, 0x02}, ++ {0x3630, 0x2e}, ++ {0x3632, 0xe2}, ++ {0x3633, 0x23}, ++ {0x3634, 0x44}, ++ {0x3636, 0x06}, ++ {0x3620, 0x64}, ++ {0x3621, 0xe0}, ++ {0x3600, 0x37}, ++ {0x3704, 0xa0}, ++ {0x3703, 0x5a}, ++ {0x3715, 0x78}, ++ {0x3717, 0x01}, ++ {0x3731, 0x02}, ++ {0x370b, 0x60}, ++ {0x3705, 0x1a}, ++ {0x3f05, 0x02}, ++ {0x3f06, 0x10}, ++ {0x3f01, 0x0a}, ++ {0x3a08, 0x01}, ++ {0x3a09, 0x4b}, ++ {0x3a0a, 0x01}, ++ {0x3a0b, 0x13}, ++ {0x3a0d, 0x04}, ++ {0x3a0e, 0x03}, ++ {0x3a0f, 0x58}, ++ {0x3a10, 0x50}, ++ {0x3a1b, 0x58}, ++ {0x3a1e, 0x50}, ++ {0x3a11, 0x60}, ++ {0x3a1f, 0x28}, ++ {0x4001, 0x02}, ++ {0x4004, 0x04}, ++ {0x4000, 0x09}, ++ {0x4837, 0x19}, ++ {0x4800, 0x34}, ++ {0x3503, 0x03}, ++ {0x0100, 0x01}, ++}; ++ ++static struct regval_list ov5647_2x2binned_10bit[] = { ++ {0x0100, 0x00}, ++ {0x0103, 0x01}, ++ {0x3034, 0x1A}, ++ {0x3035, 0x21}, ++ {0x3036, 0x62}, ++ {0x303C, 0x11}, ++ {0x3106, 0xF5}, ++ {0x3827, 0xEC}, ++ {0x370C, 0x03}, ++ {0x3612, 0x59}, ++ {0x3618, 0x00}, ++ {0x5000, 0x06}, ++ {0x5002, 0x41}, ++ {0x5003, 0x08}, ++ {0x5A00, 0x08}, ++ {0x3000, 0x00}, ++ {0x3001, 0x00}, ++ {0x3002, 0x00}, ++ {0x3016, 0x08}, ++ {0x3017, 0xE0}, ++ {0x3018, 0x44}, ++ {0x301C, 0xF8}, ++ {0x301D, 0xF0}, ++ {0x3A18, 0x00}, ++ {0x3A19, 0xF8}, ++ {0x3C01, 0x80}, ++ {0x3B07, 0x0C}, ++ {0x3800, 0x00}, ++ {0x3801, 0x00}, ++ {0x3802, 0x00}, ++ {0x3803, 0x00}, ++ {0x3804, 0x0A}, ++ {0x3805, 0x3F}, ++ {0x3806, 0x07}, ++ {0x3807, 0xA3}, ++ {0x3808, 0x05}, ++ {0x3809, 0x10}, ++ {0x380A, 0x03}, ++ {0x380B, 0xCC}, ++ {0x380C, 0x07}, ++ {0x380D, 0x68}, ++ {0x3811, 0x0c}, ++ {0x3813, 0x06}, ++ {0x3814, 0x31}, ++ {0x3815, 0x31}, ++ {0x3630, 0x2E}, ++ {0x3632, 0xE2}, ++ {0x3633, 0x23}, ++ {0x3634, 0x44}, ++ {0x3636, 0x06}, ++ {0x3620, 0x64}, ++ {0x3621, 0xE0}, ++ {0x3600, 0x37}, ++ {0x3704, 0xA0}, ++ {0x3703, 0x5A}, ++ {0x3715, 0x78}, ++ {0x3717, 0x01}, ++ {0x3731, 0x02}, ++ {0x370B, 0x60}, ++ {0x3705, 0x1A}, ++ {0x3F05, 0x02}, ++ {0x3F06, 0x10}, ++ {0x3F01, 0x0A}, ++ {0x3A08, 0x01}, ++ {0x3A09, 0x28}, ++ {0x3A0A, 0x00}, ++ {0x3A0B, 0xF6}, ++ {0x3A0D, 0x08}, ++ {0x3A0E, 0x06}, ++ {0x3A0F, 0x58}, ++ {0x3A10, 0x50}, ++ {0x3A1B, 0x58}, ++ {0x3A1E, 0x50}, ++ {0x3A11, 0x60}, ++ {0x3A1F, 0x28}, ++ {0x4001, 0x02}, ++ {0x4004, 0x04}, ++ {0x4000, 0x09}, ++ {0x4837, 0x16}, ++ {0x4800, 0x24}, ++ {0x3503, 0x03}, ++ {0x3820, 0x41}, ++ {0x3821, 0x07}, ++ {0x380E, 0x05}, ++ {0x380F, 0x9B}, ++ {0x350A, 0x00}, ++ {0x350B, 0x10}, ++ {0x3500, 0x00}, ++ {0x3501, 0x1A}, ++ {0x3502, 0xF0}, ++ {0x3212, 0xA0}, ++ {0x0100, 0x01}, ++}; ++ ++static struct regval_list ov5647_640x480_10bit[] = { ++ {0x0100, 0x00}, ++ {0x0103, 0x01}, ++ {0x3035, 0x11}, ++ {0x3036, 0x46}, ++ {0x303c, 0x11}, ++ {0x3821, 0x07}, ++ {0x3820, 0x41}, ++ {0x370c, 0x03}, ++ {0x3612, 0x59}, ++ {0x3618, 0x00}, ++ {0x5000, 0x06}, ++ {0x5003, 0x08}, ++ {0x5a00, 0x08}, ++ {0x3000, 0xff}, ++ {0x3001, 0xff}, ++ {0x3002, 0xff}, ++ {0x301d, 0xf0}, ++ {0x3a18, 0x00}, ++ {0x3a19, 0xf8}, ++ {0x3c01, 0x80}, ++ {0x3b07, 0x0c}, ++ {0x380c, 0x07}, ++ {0x380d, 0x3c}, ++ {0x380e, 0x01}, ++ {0x380f, 0xf8}, ++ {0x3814, 0x35}, ++ {0x3815, 0x35}, ++ {0x3708, 0x64}, ++ {0x3709, 0x52}, ++ {0x3808, 0x02}, ++ {0x3809, 0x80}, ++ {0x380a, 0x01}, ++ {0x380b, 0xe0}, ++ {0x3800, 0x00}, ++ {0x3801, 0x10}, ++ {0x3802, 0x00}, ++ {0x3803, 0x00}, ++ {0x3804, 0x0a}, ++ {0x3805, 0x2f}, ++ {0x3806, 0x07}, ++ {0x3807, 0x9f}, ++ {0x3630, 0x2e}, ++ {0x3632, 0xe2}, ++ {0x3633, 0x23}, ++ {0x3634, 0x44}, ++ {0x3620, 0x64}, ++ {0x3621, 0xe0}, ++ {0x3600, 0x37}, ++ {0x3704, 0xa0}, ++ {0x3703, 0x5a}, ++ {0x3715, 0x78}, ++ {0x3717, 0x01}, ++ {0x3731, 0x02}, ++ {0x370b, 0x60}, ++ {0x3705, 0x1a}, ++ {0x3f05, 0x02}, ++ {0x3f06, 0x10}, ++ {0x3f01, 0x0a}, ++ {0x3a08, 0x01}, ++ {0x3a09, 0x2e}, ++ {0x3a0a, 0x00}, ++ {0x3a0b, 0xfb}, ++ {0x3a0d, 0x02}, ++ {0x3a0e, 0x01}, ++ {0x3a0f, 0x58}, ++ {0x3a10, 0x50}, ++ {0x3a1b, 0x58}, ++ {0x3a1e, 0x50}, ++ {0x3a11, 0x60}, ++ {0x3a1f, 0x28}, ++ {0x4001, 0x02}, ++ {0x4004, 0x02}, ++ {0x4000, 0x09}, ++ {0x3000, 0x00}, ++ {0x3001, 0x00}, ++ {0x3002, 0x00}, ++ {0x3017, 0xe0}, ++ {0x301c, 0xfc}, ++ {0x3636, 0x06}, ++ {0x3016, 0x08}, ++ {0x3827, 0xec}, ++ {0x3018, 0x44}, ++ {0x3035, 0x21}, ++ {0x3106, 0xf5}, ++ {0x3034, 0x1a}, ++ {0x301c, 0xf8}, ++ {0x4800, 0x34}, ++ {0x3503, 0x03}, ++ {0x0100, 0x01}, ++}; ++ + static struct ov5647_mode supported_modes_8bit[] = { + /* +- * Original 8-bit VGA mode ++ * MODE 0: Original 8-bit VGA mode. + * Uncentred crop (top left quarter) from 2x2 binned 1296x972 image. + */ + { +@@ -233,14 +603,70 @@ static struct ov5647_mode supported_mode + .width = 640, + .height = 480 + }, +- ov5647_640x480, +- ARRAY_SIZE(ov5647_640x480) ++ ov5647_640x480_8bit, ++ ARRAY_SIZE(ov5647_640x480_8bit) + }, +- /* more modes below here... */ + }; + + static struct ov5647_mode supported_modes_10bit[] = { +- /* no 10-bit modes yet */ ++ /* ++ * MODE 0: 2592x1944 full resolution full FOV 10-bit mode. ++ */ ++ { ++ { ++ .code = MEDIA_BUS_FMT_SBGGR10_1X10, ++ .colorspace = V4L2_COLORSPACE_SRGB, ++ .field = V4L2_FIELD_NONE, ++ .width = 2592, ++ .height = 1944 ++ }, ++ ov5647_2592x1944_10bit, ++ ARRAY_SIZE(ov5647_2592x1944_10bit) ++ }, ++ /* ++ * MODE 1: 1080p30 10-bit mode. ++ * Full resolution centre-cropped down to 1080p. ++ */ ++ { ++ { ++ .code = MEDIA_BUS_FMT_SBGGR10_1X10, ++ .colorspace = V4L2_COLORSPACE_SRGB, ++ .field = V4L2_FIELD_NONE, ++ .width = 1920, ++ .height = 1080 ++ }, ++ ov5647_1080p30_10bit, ++ ARRAY_SIZE(ov5647_1080p30_10bit) ++ }, ++ /* ++ * MODE 2: 2x2 binned full FOV 10-bit mode. ++ */ ++ { ++ { ++ .code = MEDIA_BUS_FMT_SBGGR10_1X10, ++ .colorspace = V4L2_COLORSPACE_SRGB, ++ .field = V4L2_FIELD_NONE, ++ .width = 1296, ++ .height = 972 ++ }, ++ ov5647_2x2binned_10bit, ++ ARRAY_SIZE(ov5647_2x2binned_10bit) ++ }, ++ /* ++ * MODE 3: 10-bit VGA full FOV mode 60fps. ++ * 2x2 binned and subsampled down to VGA. ++ */ ++ { ++ { ++ .code = MEDIA_BUS_FMT_SBGGR10_1X10, ++ .colorspace = V4L2_COLORSPACE_SRGB, ++ .field = V4L2_FIELD_NONE, ++ .width = 640, ++ .height = 480 ++ }, ++ ov5647_640x480_10bit, ++ ARRAY_SIZE(ov5647_640x480_10bit) ++ }, + }; + + /* Use original 8-bit VGA mode as default. */ +@@ -343,11 +769,14 @@ static int __sensor_init(struct v4l2_sub + if (ret < 0) + return ret; + +- ret = ov5647_write_array(sd, state->mode->reg_list, +- state->mode->num_regs); +- if (ret < 0) { +- dev_err(&client->dev, "write sensor default regs error\n"); +- return ret; ++ if (state->write_mode_regs) { ++ ret = ov5647_write_array(sd, state->mode->reg_list, ++ state->mode->num_regs); ++ if (ret < 0) { ++ dev_err(&client->dev, "write sensor default regs error\n"); ++ return ret; ++ } ++ state->write_mode_regs = false; + } + + ret = ov5647_set_virtual_channel(sd, 0); +@@ -475,6 +904,9 @@ static int ov5647_sensor_power(struct v4 + "Camera not available, check Power\n"); + goto out; + } ++ ++ /* Write out the register set over I2C on stream-on. */ ++ ov5647->write_mode_regs = true; + } else if (!on && ov5647->power_count == 1) { + dev_dbg(&client->dev, "OV5647 power off\n"); + +@@ -650,6 +1082,12 @@ static int ov5647_set_fmt(struct v4l2_su + framefmt = v4l2_subdev_get_try_format(sd, cfg, format->pad); + *framefmt = format->format; + } else { ++ /* ++ * If we have changed modes, write the I2C register list on ++ * a stream_on(). ++ */ ++ if (state->mode != mode) ++ state->write_mode_regs = true; + state->mode = mode; + } + +@@ -967,6 +1405,9 @@ static int ov5647_probe(struct i2c_clien + /* Set the default mode before we init the subdev */ + sensor->mode = OV5647_DEFAULT_MODE; + ++ /* Write out the register set over I2C on stream-on. */ ++ sensor->write_mode_regs = true; ++ + sd = &sensor->sd; + v4l2_i2c_subdev_init(sd, client, &ov5647_subdev_ops); + sensor->sd.internal_ops = &ov5647_subdev_internal_ops; diff --git a/target/linux/bcm27xx/patches-5.10/950-0229-media-ov5647-change-defaults-to-better-match-raw-cam.patch b/target/linux/bcm27xx/patches-5.10/950-0229-media-ov5647-change-defaults-to-better-match-raw-cam.patch new file mode 100644 index 0000000000..43053890d3 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0229-media-ov5647-change-defaults-to-better-match-raw-cam.patch @@ -0,0 +1,59 @@ +From aab5d5842d718544ef906dc8cc5c221e6121160f Mon Sep 17 00:00:00 2001 +From: David Plowman +Date: Wed, 29 Jan 2020 15:31:32 +0000 +Subject: [PATCH] media: ov5647: change defaults to better match raw + camera applications. + +Specifically: + +* AWB is now off by default. + +* AEC/AGC is also off by default. + +* The default mode is changed to the 10-bit 2x2 binned mode. + +AWB and AEC/AGC can be re-enabled using the usual V4L2 controls. The +original 8-bit mode will be respected if an application requests the +8-bit format. + +Signed-off-by: David Plowman +Signed-off-by: Naushir Patuck +--- + drivers/media/i2c/ov5647.c | 10 +++++----- + 1 file changed, 5 insertions(+), 5 deletions(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -669,8 +669,8 @@ static struct ov5647_mode supported_mode + }, + }; + +-/* Use original 8-bit VGA mode as default. */ +-#define OV5647_DEFAULT_MODE (&supported_modes_8bit[0]) ++/* Use 2x2 binned 10-bit mode as default. */ ++#define OV5647_DEFAULT_MODE (&supported_modes_10bit[2]) + + static int ov5647_write(struct v4l2_subdev *sd, u16 reg, u8 val) + { +@@ -1367,18 +1367,18 @@ static int ov5647_probe(struct i2c_clien + 0, /* min */ + 1, /* max */ + 1, /* step */ +- 1); /* default */ ++ 0); /* default */ + v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, + V4L2_CID_AUTO_WHITE_BALANCE, + 0, /* min */ + 1, /* max */ + 1, /* step */ +- 1); /* default */ ++ 0); /* default */ + v4l2_ctrl_new_std_menu(&sensor->ctrls, &ov5647_ctrl_ops, + V4L2_CID_EXPOSURE_AUTO, + V4L2_EXPOSURE_MANUAL, /* max */ + 0, /* skip_mask */ +- V4L2_EXPOSURE_AUTO); /* default */ ++ V4L2_EXPOSURE_MANUAL); /* default */ + ctrl = v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, + V4L2_CID_EXPOSURE, + 4, /* min lines */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0230-media-i2c-ov5647-Add-support-for-g_selection-to-refl.patch b/target/linux/bcm27xx/patches-5.10/950-0230-media-i2c-ov5647-Add-support-for-g_selection-to-refl.patch new file mode 100644 index 0000000000..3b3bba282c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0230-media-i2c-ov5647-Add-support-for-g_selection-to-refl.patch @@ -0,0 +1,206 @@ +From 450dc10dd858314fcb5e18942b6e5260e3478f10 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 29 Apr 2020 11:46:07 +0100 +Subject: [PATCH] media: i2c: ov5647: Add support for g_selection to + reflect cropping/binning + +In order to apply lens shading correctly the client needs to know how +each mode crops or scales the image compared to the full sensor array. +Implement this (based on the imx219 equivalent). + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov5647.c | 119 ++++++++++++++++++++++++++++++------- + 1 file changed, 96 insertions(+), 23 deletions(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -70,25 +70,14 @@ + #define VAL_TERM 0xfe + #define REG_DLY 0xffff + +-#define OV5647_ROW_START 0x01 +-#define OV5647_ROW_START_MIN 0 +-#define OV5647_ROW_START_MAX 2004 +-#define OV5647_ROW_START_DEF 54 +- +-#define OV5647_COLUMN_START 0x02 +-#define OV5647_COLUMN_START_MIN 0 +-#define OV5647_COLUMN_START_MAX 2750 +-#define OV5647_COLUMN_START_DEF 16 +- +-#define OV5647_WINDOW_HEIGHT 0x03 +-#define OV5647_WINDOW_HEIGHT_MIN 2 +-#define OV5647_WINDOW_HEIGHT_MAX 2006 +-#define OV5647_WINDOW_HEIGHT_DEF 1944 +- +-#define OV5647_WINDOW_WIDTH 0x04 +-#define OV5647_WINDOW_WIDTH_MIN 2 +-#define OV5647_WINDOW_WIDTH_MAX 2752 +-#define OV5647_WINDOW_WIDTH_DEF 2592 ++/* OV5647 native and active pixel array size */ ++#define OV5647_NATIVE_WIDTH 2624U ++#define OV5647_NATIVE_HEIGHT 1956U ++ ++#define OV5647_PIXEL_ARRAY_LEFT 16U ++#define OV5647_PIXEL_ARRAY_TOP 16U ++#define OV5647_PIXEL_ARRAY_WIDTH 2592U ++#define OV5647_PIXEL_ARRAY_HEIGHT 1944U + + struct regval_list { + u16 addr; +@@ -97,6 +86,9 @@ struct regval_list { + + struct ov5647_mode { + struct v4l2_mbus_framefmt format; ++ /* Analog crop rectangle. */ ++ struct v4l2_rect crop; ++ + struct regval_list *reg_list; + unsigned int num_regs; + }; +@@ -603,6 +595,12 @@ static struct ov5647_mode supported_mode + .width = 640, + .height = 480 + }, ++ .crop = { ++ .left = 0, ++ .top = 0, ++ .width = 1280, ++ .height = 960, ++ }, + ov5647_640x480_8bit, + ARRAY_SIZE(ov5647_640x480_8bit) + }, +@@ -620,6 +618,12 @@ static struct ov5647_mode supported_mode + .width = 2592, + .height = 1944 + }, ++ .crop = { ++ .left = 0, ++ .top = 0, ++ .width = 2592, ++ .height = 1944 ++ }, + ov5647_2592x1944_10bit, + ARRAY_SIZE(ov5647_2592x1944_10bit) + }, +@@ -635,6 +639,12 @@ static struct ov5647_mode supported_mode + .width = 1920, + .height = 1080 + }, ++ .crop = { ++ .left = 348, ++ .top = 434, ++ .width = 1928, ++ .height = 1080, ++ }, + ov5647_1080p30_10bit, + ARRAY_SIZE(ov5647_1080p30_10bit) + }, +@@ -649,6 +659,12 @@ static struct ov5647_mode supported_mode + .width = 1296, + .height = 972 + }, ++ .crop = { ++ .left = 0, ++ .top = 0, ++ .width = 2592, ++ .height = 1944, ++ }, + ov5647_2x2binned_10bit, + ARRAY_SIZE(ov5647_2x2binned_10bit) + }, +@@ -664,6 +680,12 @@ static struct ov5647_mode supported_mode + .width = 640, + .height = 480 + }, ++ .crop = { ++ .left = 16, ++ .top = 0, ++ .width = 2560, ++ .height = 1920, ++ }, + ov5647_640x480_10bit, + ARRAY_SIZE(ov5647_640x480_10bit) + }, +@@ -971,6 +993,56 @@ static const struct v4l2_subdev_core_ops + #endif + }; + ++static const struct v4l2_rect * ++__ov5647_get_pad_crop(struct ov5647 *ov5647, struct v4l2_subdev_pad_config *cfg, ++ unsigned int pad, enum v4l2_subdev_format_whence which) ++{ ++ switch (which) { ++ case V4L2_SUBDEV_FORMAT_TRY: ++ return v4l2_subdev_get_try_crop(&ov5647->sd, cfg, pad); ++ case V4L2_SUBDEV_FORMAT_ACTIVE: ++ return &ov5647->mode->crop; ++ } ++ ++ return NULL; ++} ++ ++static int ov5647_get_selection(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_selection *sel) ++{ ++ switch (sel->target) { ++ case V4L2_SEL_TGT_CROP: { ++ struct ov5647 *state = to_state(sd); ++ ++ mutex_lock(&state->lock); ++ sel->r = *__ov5647_get_pad_crop(state, cfg, sel->pad, ++ sel->which); ++ mutex_unlock(&state->lock); ++ ++ return 0; ++ } ++ ++ case V4L2_SEL_TGT_NATIVE_SIZE: ++ sel->r.top = 0; ++ sel->r.left = 0; ++ sel->r.width = OV5647_NATIVE_WIDTH; ++ sel->r.height = OV5647_NATIVE_HEIGHT; ++ ++ return 0; ++ ++ case V4L2_SEL_TGT_CROP_DEFAULT: ++ sel->r.top = OV5647_PIXEL_ARRAY_TOP; ++ sel->r.left = OV5647_PIXEL_ARRAY_LEFT; ++ sel->r.width = OV5647_PIXEL_ARRAY_WIDTH; ++ sel->r.height = OV5647_PIXEL_ARRAY_HEIGHT; ++ ++ return 0; ++ } ++ ++ return -EINVAL; ++} ++ + static int ov5647_s_stream(struct v4l2_subdev *sd, int enable) + { + struct ov5647 *state = to_state(sd); +@@ -1122,6 +1194,7 @@ static const struct v4l2_subdev_pad_ops + .enum_mbus_code = ov5647_enum_mbus_code, + .set_fmt = ov5647_set_fmt, + .get_fmt = ov5647_get_fmt, ++ .get_selection = ov5647_get_selection, + .enum_frame_size = ov5647_enum_frame_size, + }; + +@@ -1170,10 +1243,10 @@ static int ov5647_open(struct v4l2_subde + v4l2_subdev_get_try_crop(sd, fh->pad, 0); + struct ov5647 *state = to_state(sd); + +- crop->left = OV5647_COLUMN_START_DEF; +- crop->top = OV5647_ROW_START_DEF; +- crop->width = OV5647_WINDOW_WIDTH_DEF; +- crop->height = OV5647_WINDOW_HEIGHT_DEF; ++ crop->left = OV5647_PIXEL_ARRAY_LEFT; ++ crop->top = OV5647_PIXEL_ARRAY_TOP; ++ crop->width = OV5647_PIXEL_ARRAY_WIDTH; ++ crop->height = OV5647_PIXEL_ARRAY_HEIGHT; + + /* Set the default format to the same as the sensor. */ + *format = state->mode->format; diff --git a/target/linux/bcm27xx/patches-5.10/950-0231-media-i2c-ov5467-Fixup-error-path-to-release-mutex.patch b/target/linux/bcm27xx/patches-5.10/950-0231-media-i2c-ov5467-Fixup-error-path-to-release-mutex.patch new file mode 100644 index 0000000000..2547aac869 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0231-media-i2c-ov5467-Fixup-error-path-to-release-mutex.patch @@ -0,0 +1,29 @@ +From 5c462e56efdb4de0e3b785082d8adae675ccaefd Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 29 Apr 2020 11:50:52 +0100 +Subject: [PATCH] media: i2c: ov5467: Fixup error path to release mutex + +"87f3ab9 media: ov5647: Add basic support for multiple sensor modes." +added a return path ov5647_set_fmt that didn't release the device +mutex that it had claimed. +Release the mutex. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov5647.c | 4 +++- + 1 file changed, 3 insertions(+), 1 deletion(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -1146,8 +1146,10 @@ static int ov5647_set_fmt(struct v4l2_su + else + mode = mode_8bit; + +- if (!mode) ++ if (!mode) { ++ mutex_unlock(&state->lock); + return -EINVAL; ++ } + + *fmt = mode->format; + if (format->which == V4L2_SUBDEV_FORMAT_TRY) { diff --git a/target/linux/bcm27xx/patches-5.10/950-0232-media-i2c-ov5647-Support-V4L2_CID_PIXEL_RATE.patch b/target/linux/bcm27xx/patches-5.10/950-0232-media-i2c-ov5647-Support-V4L2_CID_PIXEL_RATE.patch new file mode 100644 index 0000000000..78054d937f --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0232-media-i2c-ov5647-Support-V4L2_CID_PIXEL_RATE.patch @@ -0,0 +1,131 @@ +From 5cb8892104a869adaf76d40629b5a0230d32edd0 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 29 Apr 2020 12:25:13 +0100 +Subject: [PATCH] media: i2c: ov5647: Support V4L2_CID_PIXEL_RATE + +Clients need to know the pixel rate in order to compute exposure +and frame rate values. +Advertise it. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov5647.c | 31 +++++++++++++++++++++++++++---- + 1 file changed, 27 insertions(+), 4 deletions(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -89,6 +89,8 @@ struct ov5647_mode { + /* Analog crop rectangle. */ + struct v4l2_rect crop; + ++ u64 pixel_rate; ++ + struct regval_list *reg_list; + unsigned int num_regs; + }; +@@ -103,6 +105,7 @@ struct ov5647 { + struct gpio_desc *pwdn; + unsigned int flags; + struct v4l2_ctrl_handler ctrls; ++ struct v4l2_ctrl *pixel_rate; + bool write_mode_regs; + }; + +@@ -601,6 +604,7 @@ static struct ov5647_mode supported_mode + .width = 1280, + .height = 960, + }, ++ .pixel_rate = 77291670, + ov5647_640x480_8bit, + ARRAY_SIZE(ov5647_640x480_8bit) + }, +@@ -624,6 +628,7 @@ static struct ov5647_mode supported_mode + .width = 2592, + .height = 1944 + }, ++ .pixel_rate = 87500000, + ov5647_2592x1944_10bit, + ARRAY_SIZE(ov5647_2592x1944_10bit) + }, +@@ -645,6 +650,7 @@ static struct ov5647_mode supported_mode + .width = 1928, + .height = 1080, + }, ++ .pixel_rate = 81666700, + ov5647_1080p30_10bit, + ARRAY_SIZE(ov5647_1080p30_10bit) + }, +@@ -665,6 +671,7 @@ static struct ov5647_mode supported_mode + .width = 2592, + .height = 1944, + }, ++ .pixel_rate = 81666700, + ov5647_2x2binned_10bit, + ARRAY_SIZE(ov5647_2x2binned_10bit) + }, +@@ -686,6 +693,7 @@ static struct ov5647_mode supported_mode + .width = 2560, + .height = 1920, + }, ++ .pixel_rate = 55000000, + ov5647_640x480_10bit, + ARRAY_SIZE(ov5647_640x480_10bit) + }, +@@ -1163,6 +1171,11 @@ static int ov5647_set_fmt(struct v4l2_su + if (state->mode != mode) + state->write_mode_regs = true; + state->mode = mode; ++ ++ __v4l2_ctrl_modify_range(state->pixel_rate, ++ mode->pixel_rate, ++ mode->pixel_rate, 1, ++ mode->pixel_rate); + } + + mutex_unlock(&state->lock); +@@ -1379,6 +1392,9 @@ static int ov5647_s_ctrl(struct v4l2_ctr + case V4L2_CID_EXPOSURE: + ret = ov5647_s_exposure(sd, ctrl->val); + break; ++ case V4L2_CID_PIXEL_RATE: ++ /* Read-only, but we adjust it based on mode. */ ++ break; + default: + dev_info(&client->dev, + "ctrl(id:0x%x,val:0x%x) is not handled\n", +@@ -1436,7 +1452,7 @@ static int ov5647_probe(struct i2c_clien + mutex_init(&sensor->lock); + + /* Initialise controls. */ +- v4l2_ctrl_handler_init(&sensor->ctrls, 3); ++ v4l2_ctrl_handler_init(&sensor->ctrls, 6); + v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, + V4L2_CID_AUTOGAIN, + 0, /* min */ +@@ -1469,6 +1485,16 @@ static int ov5647_probe(struct i2c_clien + 32); /* default, 32 = 2.0x */ + ctrl->flags |= V4L2_CTRL_FLAG_EXECUTE_ON_WRITE; + ++ /* Set the default mode before we init the subdev */ ++ sensor->mode = OV5647_DEFAULT_MODE; ++ ++ /* By default, PIXEL_RATE is read only, but it does change per mode */ ++ sensor->pixel_rate = v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, ++ V4L2_CID_PIXEL_RATE, ++ sensor->mode->pixel_rate, ++ sensor->mode->pixel_rate, 1, ++ sensor->mode->pixel_rate); ++ + if (sensor->ctrls.error) { + ret = sensor->ctrls.error; + dev_err(&client->dev, "%s control init failed (%d)\n", +@@ -1477,9 +1503,6 @@ static int ov5647_probe(struct i2c_clien + } + sensor->sd.ctrl_handler = &sensor->ctrls; + +- /* Set the default mode before we init the subdev */ +- sensor->mode = OV5647_DEFAULT_MODE; +- + /* Write out the register set over I2C on stream-on. */ + sensor->write_mode_regs = true; + diff --git a/target/linux/bcm27xx/patches-5.10/950-0233-media-i2c-ov5647-Set-V4L2_SUBDEV_FL_HAS_EVENTS-flag.patch b/target/linux/bcm27xx/patches-5.10/950-0233-media-i2c-ov5647-Set-V4L2_SUBDEV_FL_HAS_EVENTS-flag.patch new file mode 100644 index 0000000000..1f7710e382 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0233-media-i2c-ov5647-Set-V4L2_SUBDEV_FL_HAS_EVENTS-flag.patch @@ -0,0 +1,143 @@ +From 29e3826878f43cd88414824be055cf5fcd57ab23 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 29 Apr 2020 17:25:56 +0100 +Subject: [PATCH] media: i2c: ov5647: Set V4L2_SUBDEV_FL_HAS_EVENTS + flag + +The ov5647 subdev can generate control events, therefore set +the V4L2_SUBDEV_FL_HAS_EVENTS flag. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov5647.c | 29 +++++++++++++++++++++++++++-- + 1 file changed, 27 insertions(+), 2 deletions(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -90,6 +90,8 @@ struct ov5647_mode { + struct v4l2_rect crop; + + u64 pixel_rate; ++ /* HTS as defined in the register set (0x380C/0x380D) */ ++ int hts; + + struct regval_list *reg_list; + unsigned int num_regs; +@@ -106,6 +108,7 @@ struct ov5647 { + unsigned int flags; + struct v4l2_ctrl_handler ctrls; + struct v4l2_ctrl *pixel_rate; ++ struct v4l2_ctrl *hblank; + bool write_mode_regs; + }; + +@@ -605,6 +608,7 @@ static struct ov5647_mode supported_mode + .height = 960, + }, + .pixel_rate = 77291670, ++ .hts = 1896, + ov5647_640x480_8bit, + ARRAY_SIZE(ov5647_640x480_8bit) + }, +@@ -629,6 +633,7 @@ static struct ov5647_mode supported_mode + .height = 1944 + }, + .pixel_rate = 87500000, ++ .hts = 2844, + ov5647_2592x1944_10bit, + ARRAY_SIZE(ov5647_2592x1944_10bit) + }, +@@ -651,6 +656,7 @@ static struct ov5647_mode supported_mode + .height = 1080, + }, + .pixel_rate = 81666700, ++ .hts = 2416, + ov5647_1080p30_10bit, + ARRAY_SIZE(ov5647_1080p30_10bit) + }, +@@ -672,6 +678,7 @@ static struct ov5647_mode supported_mode + .height = 1944, + }, + .pixel_rate = 81666700, ++ .hts = 1896, + ov5647_2x2binned_10bit, + ARRAY_SIZE(ov5647_2x2binned_10bit) + }, +@@ -694,6 +701,7 @@ static struct ov5647_mode supported_mode + .height = 1920, + }, + .pixel_rate = 55000000, ++ .hts = 1852, + ov5647_640x480_10bit, + ARRAY_SIZE(ov5647_640x480_10bit) + }, +@@ -1168,6 +1176,8 @@ static int ov5647_set_fmt(struct v4l2_su + * If we have changed modes, write the I2C register list on + * a stream_on(). + */ ++ int hblank; ++ + if (state->mode != mode) + state->write_mode_regs = true; + state->mode = mode; +@@ -1176,6 +1186,9 @@ static int ov5647_set_fmt(struct v4l2_su + mode->pixel_rate, + mode->pixel_rate, 1, + mode->pixel_rate); ++ hblank = mode->hts - mode->format.width; ++ __v4l2_ctrl_modify_range(state->hblank, hblank, hblank, 1, ++ hblank); + } + + mutex_unlock(&state->lock); +@@ -1395,6 +1408,9 @@ static int ov5647_s_ctrl(struct v4l2_ctr + case V4L2_CID_PIXEL_RATE: + /* Read-only, but we adjust it based on mode. */ + break; ++ case V4L2_CID_HBLANK: ++ /* Read-only, but we adjust it based on mode. */ ++ break; + default: + dev_info(&client->dev, + "ctrl(id:0x%x,val:0x%x) is not handled\n", +@@ -1419,6 +1435,7 @@ static int ov5647_probe(struct i2c_clien + struct device_node *np = client->dev.of_node; + u32 xclk_freq; + struct v4l2_ctrl *ctrl; ++ int hblank; + + sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL); + if (!sensor) +@@ -1452,7 +1469,7 @@ static int ov5647_probe(struct i2c_clien + mutex_init(&sensor->lock); + + /* Initialise controls. */ +- v4l2_ctrl_handler_init(&sensor->ctrls, 6); ++ v4l2_ctrl_handler_init(&sensor->ctrls, 7); + v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, + V4L2_CID_AUTOGAIN, + 0, /* min */ +@@ -1495,6 +1512,13 @@ static int ov5647_probe(struct i2c_clien + sensor->mode->pixel_rate, 1, + sensor->mode->pixel_rate); + ++ /* By default, HBLANK is read only, but it does change per mode */ ++ hblank = sensor->mode->hts - sensor->mode->format.width; ++ sensor->hblank = v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, ++ V4L2_CID_HBLANK, hblank, hblank, 1, ++ hblank); ++ sensor->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY; ++ + if (sensor->ctrls.error) { + ret = sensor->ctrls.error; + dev_err(&client->dev, "%s control init failed (%d)\n", +@@ -1509,7 +1533,8 @@ static int ov5647_probe(struct i2c_clien + sd = &sensor->sd; + v4l2_i2c_subdev_init(sd, client, &ov5647_subdev_ops); + sensor->sd.internal_ops = &ov5647_subdev_internal_ops; +- sensor->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; ++ sensor->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | ++ V4L2_SUBDEV_FL_HAS_EVENTS; + + sensor->pad.flags = MEDIA_PAD_FL_SOURCE; + sd->entity.function = MEDIA_ENT_F_CAM_SENSOR; diff --git a/target/linux/bcm27xx/patches-5.10/950-0234-media-i2c-ov5647-Add-support-for-V4L2_CID_VBLANK.patch b/target/linux/bcm27xx/patches-5.10/950-0234-media-i2c-ov5647-Add-support-for-V4L2_CID_VBLANK.patch new file mode 100644 index 0000000000..53a6dad006 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0234-media-i2c-ov5647-Add-support-for-V4L2_CID_VBLANK.patch @@ -0,0 +1,205 @@ +From 95a10a4709eea202f3ce833fdeb9b30c17d80148 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 29 Apr 2020 21:39:58 +0100 +Subject: [PATCH] media: i2c: ov5647: Add support for V4L2_CID_VBLANK + +Adds vblank control to allow for frame rate control. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov5647.c | 65 ++++++++++++++++++++++++++++++++------ + 1 file changed, 55 insertions(+), 10 deletions(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -61,6 +61,8 @@ + #define OV5647_REG_AEC_AGC 0x3503 + #define OV5647_REG_GAIN_HI 0x350A + #define OV5647_REG_GAIN_LO 0x350B ++#define OV5647_REG_VTS_HI 0x380e ++#define OV5647_REG_VTS_LO 0x380f + #define OV5647_REG_FRAME_OFF_NUMBER 0x4202 + #define OV5647_REG_MIPI_CTRL00 0x4800 + #define OV5647_REG_MIPI_CTRL14 0x4814 +@@ -79,6 +81,9 @@ + #define OV5647_PIXEL_ARRAY_WIDTH 2592U + #define OV5647_PIXEL_ARRAY_HEIGHT 1944U + ++#define OV5647_VBLANK_MIN 4 ++#define OV5647_VTS_MAX 32767 ++ + struct regval_list { + u16 addr; + u8 data; +@@ -92,6 +97,8 @@ struct ov5647_mode { + u64 pixel_rate; + /* HTS as defined in the register set (0x380C/0x380D) */ + int hts; ++ /* Default VTS value for this mode */ ++ int vts_def; + + struct regval_list *reg_list; + unsigned int num_regs; +@@ -109,6 +116,7 @@ struct ov5647 { + struct v4l2_ctrl_handler ctrls; + struct v4l2_ctrl *pixel_rate; + struct v4l2_ctrl *hblank; ++ struct v4l2_ctrl *vblank; + bool write_mode_regs; + }; + +@@ -161,8 +169,6 @@ static struct regval_list ov5647_640x480 + {0x3b07, 0x0c}, + {0x380c, 0x07}, + {0x380d, 0x68}, +- {0x380e, 0x03}, +- {0x380f, 0xd8}, + {0x3814, 0x31}, + {0x3815, 0x31}, + {0x3708, 0x64}, +@@ -251,8 +257,6 @@ static struct regval_list ov5647_2592x19 + {0x3b07, 0x0c}, + {0x380c, 0x0b}, + {0x380d, 0x1c}, +- {0x380e, 0x07}, +- {0x380f, 0xb0}, + {0x3814, 0x11}, + {0x3815, 0x11}, + {0x3708, 0x64}, +@@ -342,8 +346,6 @@ static struct regval_list ov5647_1080p30 + {0x3b07, 0x0c}, + {0x380c, 0x09}, + {0x380d, 0x70}, +- {0x380e, 0x04}, +- {0x380f, 0x50}, + {0x3814, 0x11}, + {0x3815, 0x11}, + {0x3708, 0x64}, +@@ -485,8 +487,6 @@ static struct regval_list ov5647_2x2binn + {0x3503, 0x03}, + {0x3820, 0x41}, + {0x3821, 0x07}, +- {0x380E, 0x05}, +- {0x380F, 0x9B}, + {0x350A, 0x00}, + {0x350B, 0x10}, + {0x3500, 0x00}, +@@ -520,8 +520,6 @@ static struct regval_list ov5647_640x480 + {0x3b07, 0x0c}, + {0x380c, 0x07}, + {0x380d, 0x3c}, +- {0x380e, 0x01}, +- {0x380f, 0xf8}, + {0x3814, 0x35}, + {0x3815, 0x35}, + {0x3708, 0x64}, +@@ -609,6 +607,7 @@ static struct ov5647_mode supported_mode + }, + .pixel_rate = 77291670, + .hts = 1896, ++ .vts_def = 0x3d8, + ov5647_640x480_8bit, + ARRAY_SIZE(ov5647_640x480_8bit) + }, +@@ -634,6 +633,7 @@ static struct ov5647_mode supported_mode + }, + .pixel_rate = 87500000, + .hts = 2844, ++ .vts_def = 0x7b0, + ov5647_2592x1944_10bit, + ARRAY_SIZE(ov5647_2592x1944_10bit) + }, +@@ -657,6 +657,7 @@ static struct ov5647_mode supported_mode + }, + .pixel_rate = 81666700, + .hts = 2416, ++ .vts_def = 0x450, + ov5647_1080p30_10bit, + ARRAY_SIZE(ov5647_1080p30_10bit) + }, +@@ -679,6 +680,7 @@ static struct ov5647_mode supported_mode + }, + .pixel_rate = 81666700, + .hts = 1896, ++ .vts_def = 0x59b, + ov5647_2x2binned_10bit, + ARRAY_SIZE(ov5647_2x2binned_10bit) + }, +@@ -702,6 +704,7 @@ static struct ov5647_mode supported_mode + }, + .pixel_rate = 55000000, + .hts = 1852, ++ .vts_def = 0x1f8, + ov5647_640x480_10bit, + ARRAY_SIZE(ov5647_640x480_10bit) + }, +@@ -710,6 +713,29 @@ static struct ov5647_mode supported_mode + /* Use 2x2 binned 10-bit mode as default. */ + #define OV5647_DEFAULT_MODE (&supported_modes_10bit[2]) + ++static int ov5647_write16(struct v4l2_subdev *sd, u16 reg, u16 val) ++{ ++ int ret; ++ unsigned char data[4] = { reg >> 8, reg & 0xff, val >> 8, val & 0xff}; ++ struct i2c_client *client = v4l2_get_subdevdata(sd); ++ ++ ret = i2c_master_send(client, data, 4); ++ /* ++ * Writing the wrong number of bytes also needs to be flagged as an ++ * error. Success needs to produce a 0 return code. ++ */ ++ if (ret == 4) { ++ ret = 0; ++ } else { ++ dev_dbg(&client->dev, "%s: i2c write error, reg: %x\n", ++ __func__, reg); ++ if (ret >= 0) ++ ret = -EINVAL; ++ } ++ ++ return ret; ++} ++ + static int ov5647_write(struct v4l2_subdev *sd, u16 reg, u8 val) + { + int ret; +@@ -1189,6 +1215,14 @@ static int ov5647_set_fmt(struct v4l2_su + hblank = mode->hts - mode->format.width; + __v4l2_ctrl_modify_range(state->hblank, hblank, hblank, 1, + hblank); ++ ++ __v4l2_ctrl_modify_range(state->vblank, ++ OV5647_VBLANK_MIN, ++ OV5647_VTS_MAX - mode->format.height, ++ 1, ++ mode->vts_def - mode->format.height); ++ __v4l2_ctrl_s_ctrl(state->vblank, ++ mode->vts_def - mode->format.height); + } + + mutex_unlock(&state->lock); +@@ -1411,6 +1445,10 @@ static int ov5647_s_ctrl(struct v4l2_ctr + case V4L2_CID_HBLANK: + /* Read-only, but we adjust it based on mode. */ + break; ++ case V4L2_CID_VBLANK: ++ ret = ov5647_write16(sd, OV5647_REG_VTS_HI, ++ state->mode->format.height + ctrl->val); ++ break; + default: + dev_info(&client->dev, + "ctrl(id:0x%x,val:0x%x) is not handled\n", +@@ -1519,6 +1557,13 @@ static int ov5647_probe(struct i2c_clien + hblank); + sensor->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY; + ++ sensor->vblank = v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, ++ V4L2_CID_VBLANK, OV5647_VBLANK_MIN, ++ OV5647_VTS_MAX - ++ sensor->mode->format.height, 1, ++ sensor->mode->vts_def - ++ sensor->mode->format.height); ++ + if (sensor->ctrls.error) { + ret = sensor->ctrls.error; + dev_err(&client->dev, "%s control init failed (%d)\n", diff --git a/target/linux/bcm27xx/patches-5.10/950-0235-media-i2c-ov5647-Neither-analogue-gain-nor-exposure-.patch b/target/linux/bcm27xx/patches-5.10/950-0235-media-i2c-ov5647-Neither-analogue-gain-nor-exposure-.patch new file mode 100644 index 0000000000..b1505e7d06 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0235-media-i2c-ov5647-Neither-analogue-gain-nor-exposure-.patch @@ -0,0 +1,58 @@ +From 05a1c88d9b8dd344edfce3eaa00a3cac866cf3ad Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 29 Apr 2020 21:47:25 +0100 +Subject: [PATCH] media: i2c: ov5647: Neither analogue gain nor + exposure need EXECUTE_ON_WRITE + +The controls for analogue gain and exposure were defined with +V4L2_CTRL_FLAG_EXECUTE_ON_WRITE. This is not required as we only need +to send changes to the sensor. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov5647.c | 27 ++++++++++++--------------- + 1 file changed, 12 insertions(+), 15 deletions(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -1472,7 +1472,6 @@ static int ov5647_probe(struct i2c_clien + struct v4l2_subdev *sd; + struct device_node *np = client->dev.of_node; + u32 xclk_freq; +- struct v4l2_ctrl *ctrl; + int hblank; + + sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL); +@@ -1525,20 +1524,18 @@ static int ov5647_probe(struct i2c_clien + V4L2_EXPOSURE_MANUAL, /* max */ + 0, /* skip_mask */ + V4L2_EXPOSURE_MANUAL); /* default */ +- ctrl = v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, +- V4L2_CID_EXPOSURE, +- 4, /* min lines */ +- 65535, /* max lines (4+8+4 bits)*/ +- 1, /* step */ +- 1000); /* default number of lines */ +- ctrl->flags |= V4L2_CTRL_FLAG_EXECUTE_ON_WRITE; +- ctrl = v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, +- V4L2_CID_ANALOGUE_GAIN, +- 16, /* min, 16 = 1.0x */ +- 1023, /* max (10 bits) */ +- 1, /* step */ +- 32); /* default, 32 = 2.0x */ +- ctrl->flags |= V4L2_CTRL_FLAG_EXECUTE_ON_WRITE; ++ v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, ++ V4L2_CID_EXPOSURE, ++ 4, /* min lines */ ++ 65535, /* max lines (4+8+4 bits)*/ ++ 1, /* step */ ++ 1000); /* default number of lines */ ++ v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, ++ V4L2_CID_ANALOGUE_GAIN, ++ 16, /* min, 16 = 1.0x */ ++ 1023, /* max (10 bits) */ ++ 1, /* step */ ++ 32); /* default, 32 = 2.0x */ + + /* Set the default mode before we init the subdev */ + sensor->mode = OV5647_DEFAULT_MODE; diff --git a/target/linux/bcm27xx/patches-5.10/950-0236-media-i2c-ov5647-Use-member-names-in-mode-tables.patch b/target/linux/bcm27xx/patches-5.10/950-0236-media-i2c-ov5647-Use-member-names-in-mode-tables.patch new file mode 100644 index 0000000000..e96e6a40b1 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0236-media-i2c-ov5647-Use-member-names-in-mode-tables.patch @@ -0,0 +1,111 @@ +From 1073eef3ada930c9c35b2b0da30828cfe1ea4024 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 29 Apr 2020 22:11:01 +0100 +Subject: [PATCH] media: i2c: ov5647: Use member names in mode tables + +To make adding new members to the mode structures easier, use +the member names in the initialisers. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov5647.c | 30 +++++++++++++++--------------- + 1 file changed, 15 insertions(+), 15 deletions(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -592,7 +592,7 @@ static struct ov5647_mode supported_mode + * Uncentred crop (top left quarter) from 2x2 binned 1296x972 image. + */ + { +- { ++ .format = { + .code = MEDIA_BUS_FMT_SBGGR8_1X8, + .colorspace = V4L2_COLORSPACE_SRGB, + .field = V4L2_FIELD_NONE, +@@ -608,8 +608,8 @@ static struct ov5647_mode supported_mode + .pixel_rate = 77291670, + .hts = 1896, + .vts_def = 0x3d8, +- ov5647_640x480_8bit, +- ARRAY_SIZE(ov5647_640x480_8bit) ++ .reg_list = ov5647_640x480_8bit, ++ .num_regs = ARRAY_SIZE(ov5647_640x480_8bit) + }, + }; + +@@ -618,7 +618,7 @@ static struct ov5647_mode supported_mode + * MODE 0: 2592x1944 full resolution full FOV 10-bit mode. + */ + { +- { ++ .format = { + .code = MEDIA_BUS_FMT_SBGGR10_1X10, + .colorspace = V4L2_COLORSPACE_SRGB, + .field = V4L2_FIELD_NONE, +@@ -634,15 +634,15 @@ static struct ov5647_mode supported_mode + .pixel_rate = 87500000, + .hts = 2844, + .vts_def = 0x7b0, +- ov5647_2592x1944_10bit, +- ARRAY_SIZE(ov5647_2592x1944_10bit) ++ .reg_list = ov5647_2592x1944_10bit, ++ .num_regs = ARRAY_SIZE(ov5647_2592x1944_10bit) + }, + /* + * MODE 1: 1080p30 10-bit mode. + * Full resolution centre-cropped down to 1080p. + */ + { +- { ++ .format = { + .code = MEDIA_BUS_FMT_SBGGR10_1X10, + .colorspace = V4L2_COLORSPACE_SRGB, + .field = V4L2_FIELD_NONE, +@@ -658,14 +658,14 @@ static struct ov5647_mode supported_mode + .pixel_rate = 81666700, + .hts = 2416, + .vts_def = 0x450, +- ov5647_1080p30_10bit, +- ARRAY_SIZE(ov5647_1080p30_10bit) ++ .reg_list = ov5647_1080p30_10bit, ++ .num_regs = ARRAY_SIZE(ov5647_1080p30_10bit) + }, + /* + * MODE 2: 2x2 binned full FOV 10-bit mode. + */ + { +- { ++ .format = { + .code = MEDIA_BUS_FMT_SBGGR10_1X10, + .colorspace = V4L2_COLORSPACE_SRGB, + .field = V4L2_FIELD_NONE, +@@ -681,15 +681,15 @@ static struct ov5647_mode supported_mode + .pixel_rate = 81666700, + .hts = 1896, + .vts_def = 0x59b, +- ov5647_2x2binned_10bit, +- ARRAY_SIZE(ov5647_2x2binned_10bit) ++ .reg_list = ov5647_2x2binned_10bit, ++ .num_regs = ARRAY_SIZE(ov5647_2x2binned_10bit) + }, + /* + * MODE 3: 10-bit VGA full FOV mode 60fps. + * 2x2 binned and subsampled down to VGA. + */ + { +- { ++ .format = { + .code = MEDIA_BUS_FMT_SBGGR10_1X10, + .colorspace = V4L2_COLORSPACE_SRGB, + .field = V4L2_FIELD_NONE, +@@ -705,8 +705,8 @@ static struct ov5647_mode supported_mode + .pixel_rate = 55000000, + .hts = 1852, + .vts_def = 0x1f8, +- ov5647_640x480_10bit, +- ARRAY_SIZE(ov5647_640x480_10bit) ++ .reg_list = ov5647_640x480_10bit, ++ .num_regs = ARRAY_SIZE(ov5647_640x480_10bit) + }, + }; + diff --git a/target/linux/bcm27xx/patches-5.10/950-0237-media-i2c-ov5647-Advertise-the-correct-exposure-rang.patch b/target/linux/bcm27xx/patches-5.10/950-0237-media-i2c-ov5647-Advertise-the-correct-exposure-rang.patch new file mode 100644 index 0000000000..6bdde3a7ab --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0237-media-i2c-ov5647-Advertise-the-correct-exposure-rang.patch @@ -0,0 +1,119 @@ +From 7048b8678ac96eb512adfb18990eff0c9b8109f5 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 30 Apr 2020 11:03:00 +0100 +Subject: [PATCH] media: i2c: ov5647: Advertise the correct exposure + range + +Exposure is clipped by the VTS of the mode, so needs to be updated as +and when this is changed. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov5647.c | 47 +++++++++++++++++++++++++++++++------- + 1 file changed, 39 insertions(+), 8 deletions(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -84,6 +84,11 @@ + #define OV5647_VBLANK_MIN 4 + #define OV5647_VTS_MAX 32767 + ++#define OV5647_EXPOSURE_MIN 4 ++#define OV5647_EXPOSURE_STEP 1 ++#define OV5647_EXPOSURE_DEFAULT 1000 ++#define OV5647_EXPOSURE_MAX 65535 ++ + struct regval_list { + u16 addr; + u8 data; +@@ -117,6 +122,7 @@ struct ov5647 { + struct v4l2_ctrl *pixel_rate; + struct v4l2_ctrl *hblank; + struct v4l2_ctrl *vblank; ++ struct v4l2_ctrl *exposure; + bool write_mode_regs; + }; + +@@ -1202,7 +1208,7 @@ static int ov5647_set_fmt(struct v4l2_su + * If we have changed modes, write the I2C register list on + * a stream_on(). + */ +- int hblank; ++ int exposure_max, exposure_def, hblank; + + if (state->mode != mode) + state->write_mode_regs = true; +@@ -1223,6 +1229,15 @@ static int ov5647_set_fmt(struct v4l2_su + mode->vts_def - mode->format.height); + __v4l2_ctrl_s_ctrl(state->vblank, + mode->vts_def - mode->format.height); ++ ++ exposure_max = mode->vts_def - 4; ++ exposure_def = (exposure_max < OV5647_EXPOSURE_DEFAULT) ? ++ exposure_max : OV5647_EXPOSURE_DEFAULT; ++ __v4l2_ctrl_modify_range(state->exposure, ++ state->exposure->minimum, ++ exposure_max, ++ state->exposure->step, ++ exposure_def); + } + + mutex_unlock(&state->lock); +@@ -1415,6 +1430,19 @@ static int ov5647_s_ctrl(struct v4l2_ctr + + /* v4l2_ctrl_lock() locks our own mutex */ + ++ if (ctrl->id == V4L2_CID_VBLANK) { ++ int exposure_max, exposure_def; ++ ++ /* Update max exposure while meeting expected vblanking */ ++ exposure_max = state->mode->format.height + ctrl->val - 4; ++ exposure_def = (exposure_max < OV5647_EXPOSURE_DEFAULT) ? ++ exposure_max : OV5647_EXPOSURE_DEFAULT; ++ __v4l2_ctrl_modify_range(state->exposure, ++ state->exposure->minimum, ++ exposure_max, state->exposure->step, ++ exposure_def); ++ } ++ + /* + * If the device is not powered up by the host driver do + * not apply any controls to H/W at this time. Instead +@@ -1472,7 +1500,7 @@ static int ov5647_probe(struct i2c_clien + struct v4l2_subdev *sd; + struct device_node *np = client->dev.of_node; + u32 xclk_freq; +- int hblank; ++ int hblank, exposure_max, exposure_def; + + sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL); + if (!sensor) +@@ -1525,12 +1553,6 @@ static int ov5647_probe(struct i2c_clien + 0, /* skip_mask */ + V4L2_EXPOSURE_MANUAL); /* default */ + v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, +- V4L2_CID_EXPOSURE, +- 4, /* min lines */ +- 65535, /* max lines (4+8+4 bits)*/ +- 1, /* step */ +- 1000); /* default number of lines */ +- v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, + V4L2_CID_ANALOGUE_GAIN, + 16, /* min, 16 = 1.0x */ + 1023, /* max (10 bits) */ +@@ -1540,6 +1562,15 @@ static int ov5647_probe(struct i2c_clien + /* Set the default mode before we init the subdev */ + sensor->mode = OV5647_DEFAULT_MODE; + ++ exposure_max = sensor->mode->vts_def - 4; ++ exposure_def = (exposure_max < OV5647_EXPOSURE_DEFAULT) ? ++ exposure_max : OV5647_EXPOSURE_DEFAULT; ++ sensor->exposure = v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, ++ V4L2_CID_EXPOSURE, ++ OV5647_EXPOSURE_MIN, exposure_max, ++ OV5647_EXPOSURE_STEP, ++ exposure_def); ++ + /* By default, PIXEL_RATE is read only, but it does change per mode */ + sensor->pixel_rate = v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, + V4L2_CID_PIXEL_RATE, diff --git a/target/linux/bcm27xx/patches-5.10/950-0238-media-bcm2835-unicam-Add-support-for-VIDIOC_-S-G-_SE.patch b/target/linux/bcm27xx/patches-5.10/950-0238-media-bcm2835-unicam-Add-support-for-VIDIOC_-S-G-_SE.patch new file mode 100644 index 0000000000..e875f6c77b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0238-media-bcm2835-unicam-Add-support-for-VIDIOC_-S-G-_SE.patch @@ -0,0 +1,82 @@ +From c4b4c783173ae54db7f9f656b25b45f7719f068d Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 29 Apr 2020 16:45:02 +0100 +Subject: [PATCH] media: bcm2835-unicam: Add support for + VIDIOC_[S|G]_SELECTION + +Sensors are now reflecting cropping and scaling parameters through +the selection API, therefore Unicam needs to forward the requests +through to the subdev. + +Signed-off-by: Dave Stevenson +--- + .../media/platform/bcm2835/bcm2835-unicam.c | 44 +++++++++++++++++++ + 1 file changed, 44 insertions(+) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -1898,6 +1898,39 @@ static int unicam_g_edid(struct file *fi + return v4l2_subdev_call(dev->sensor, pad, get_edid, edid); + } + ++static int unicam_s_selection(struct file *file, void *priv, ++ struct v4l2_selection *sel) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ struct v4l2_subdev_selection sdsel = { ++ .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ .target = sel->target, ++ .flags = sel->flags, ++ .r = sel->r, ++ }; ++ ++ return v4l2_subdev_call(dev->sensor, pad, set_selection, NULL, &sdsel); ++} ++ ++static int unicam_g_selection(struct file *file, void *priv, ++ struct v4l2_selection *sel) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ struct v4l2_subdev_selection sdsel = { ++ .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ .target = sel->target, ++ }; ++ int ret; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, get_selection, NULL, &sdsel); ++ if (!ret) ++ sel->r = sdsel.r; ++ ++ return ret; ++} ++ + static int unicam_enum_framesizes(struct file *file, void *priv, + struct v4l2_frmsizeenum *fsize) + { +@@ -2218,6 +2251,9 @@ static const struct v4l2_ioctl_ops unica + .vidioc_enum_framesizes = unicam_enum_framesizes, + .vidioc_enum_frameintervals = unicam_enum_frameintervals, + ++ .vidioc_g_selection = unicam_g_selection, ++ .vidioc_s_selection = unicam_s_selection, ++ + .vidioc_g_parm = unicam_g_parm, + .vidioc_s_parm = unicam_s_parm, + +@@ -2446,6 +2482,14 @@ static int register_node(struct unicam_d + !v4l2_subdev_has_op(unicam->sensor, pad, enum_frame_size)) + v4l2_disable_ioctl(&node->video_dev, VIDIOC_ENUM_FRAMESIZES); + ++ if (node->pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, pad, set_selection)) ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_SELECTION); ++ ++ if (node->pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, pad, get_selection)) ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_SELECTION); ++ + ret = video_register_device(vdev, VFL_TYPE_VIDEO, -1); + if (ret) { + unicam_err(unicam, "Unable to register video device.\n"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0239-media-bcm2835-unicam-Do-not-stop-streaming-in-unicam.patch b/target/linux/bcm27xx/patches-5.10/950-0239-media-bcm2835-unicam-Do-not-stop-streaming-in-unicam.patch new file mode 100644 index 0000000000..54b78d639a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0239-media-bcm2835-unicam-Do-not-stop-streaming-in-unicam.patch @@ -0,0 +1,28 @@ +From 533e6df1f7cc3aa022319f4419b3a38e7b76ce16 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 29 Apr 2020 22:05:09 +0100 +Subject: [PATCH] media: bcm2835-unicam: Do not stop streaming in + unicam_release + +unicam_release calls _vb2_fop_release, which will call stop_streaming +if that particular node was streaming. Calling it unconditionally (as +the code was) means that if a second handle was opened eg to alter +a setting, on closing that connection it also stopped Unicam. + +Signed-off-by: Dave Stevenson +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 3 --- + 1 file changed, 3 deletions(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -2204,9 +2204,6 @@ static int unicam_release(struct file *f + if (fh_singular) + v4l2_subdev_call(sd, core, s_power, 0); + +- if (node->streaming) +- unicam_stop_streaming(&node->buffer_queue); +- + node->open--; + mutex_unlock(&node->lock); + diff --git a/target/linux/bcm27xx/patches-5.10/950-0240-media-bcm2835-unicam-Fix-reference-counting-in-unica.patch b/target/linux/bcm27xx/patches-5.10/950-0240-media-bcm2835-unicam-Fix-reference-counting-in-unica.patch new file mode 100644 index 0000000000..5b1ef1b468 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0240-media-bcm2835-unicam-Fix-reference-counting-in-unica.patch @@ -0,0 +1,38 @@ +From 0d2110a5d2764c80179590e707929d0e6dda0c6d Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 30 Apr 2020 09:52:50 +0100 +Subject: [PATCH] media: bcm2835-unicam: Fix reference counting in + unicam_open + +The reference counting of node->open was only incremented after +a check that the node was v4l2_fh_is_singular_file, which resulted +in the counting going wrong and s_power not being called at an +appropriate time. + +Signed-off-by: Dave Stevenson +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 4 +++- + 1 file changed, 3 insertions(+), 1 deletion(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -2170,16 +2170,18 @@ static int unicam_open(struct file *file + goto unlock; + } + ++ node->open++; ++ + if (!v4l2_fh_is_singular_file(file)) + goto unlock; + + ret = v4l2_subdev_call(dev->sensor, core, s_power, 1); + if (ret < 0 && ret != -ENOIOCTLCMD) { + v4l2_fh_release(file); ++ node->open--; + goto unlock; + } + +- node->open++; + ret = 0; + + unlock: diff --git a/target/linux/bcm27xx/patches-5.10/950-0241-media-i2c-tc358743-Fix-fallthrough-warning.patch b/target/linux/bcm27xx/patches-5.10/950-0241-media-i2c-tc358743-Fix-fallthrough-warning.patch new file mode 100644 index 0000000000..819ab16f37 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0241-media-i2c-tc358743-Fix-fallthrough-warning.patch @@ -0,0 +1,20 @@ +From 973e92cd9ff33dcf24492457e5bae6554f938e23 Mon Sep 17 00:00:00 2001 +From: Jacko Dirks +Date: Tue, 5 May 2020 14:28:14 +0200 +Subject: [PATCH] media: i2c: tc358743: Fix fallthrough warning + +Signed-off-by: Jacko Dirks +--- + drivers/media/i2c/tc358743.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/media/i2c/tc358743.c ++++ b/drivers/media/i2c/tc358743.c +@@ -2006,6 +2006,7 @@ static int tc358743_probe_of(struct tc35 + switch (bps_pr_lane) { + default: + dev_warn(dev, "untested bps per lane: %u bps\n", bps_pr_lane); ++ /* fall through */ + case 594000000U: + state->pdata.lineinitcnt = 0xe80; + state->pdata.lptxtimecnt = 0x003; diff --git a/target/linux/bcm27xx/patches-5.10/950-0242-media-bcm2835-unicam-Fix-uninitialized-warning.patch b/target/linux/bcm27xx/patches-5.10/950-0242-media-bcm2835-unicam-Fix-uninitialized-warning.patch new file mode 100644 index 0000000000..83cc78f84e --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0242-media-bcm2835-unicam-Fix-uninitialized-warning.patch @@ -0,0 +1,21 @@ +From 3f024ccec9f9b661a5a7e37760fbc2558095a0a8 Mon Sep 17 00:00:00 2001 +From: Jacko Dirks +Date: Tue, 5 May 2020 14:33:31 +0200 +Subject: [PATCH] media: bcm2835: unicam: Fix uninitialized warning + +Signed-off-by: Jacko Dirks +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -1001,7 +1001,7 @@ const struct unicam_fmt *get_first_suppo + { + struct v4l2_subdev_mbus_code_enum mbus_code; + const struct unicam_fmt *fmt = NULL; +- int ret; ++ int ret = 0; + int j; + + for (j = 0; ret != -EINVAL && ret != -ENOIOCTLCMD; ++j) { diff --git a/target/linux/bcm27xx/patches-5.10/950-0243-video-bcm2708_fb-Disable-FB-if-no-displays-found.patch b/target/linux/bcm27xx/patches-5.10/950-0243-video-bcm2708_fb-Disable-FB-if-no-displays-found.patch new file mode 100644 index 0000000000..a6fc3f1360 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0243-video-bcm2708_fb-Disable-FB-if-no-displays-found.patch @@ -0,0 +1,34 @@ +From 927defe02be209d870171b385673c58b6dfa6964 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 5 May 2020 19:45:41 +0100 +Subject: [PATCH] video: bcm2708_fb: Disable FB if no displays found + +If the firmware hasn't detected a display, the driver would assume +one display was available, but because it had failed to retrieve the +display size it would try to allocate a zero-sized buffer. + +Avoid the allocation failure by bailing out early if no display is +found. + +See: https://github.com/raspberrypi/linux/issues/3598 + +Signed-off-by: Phil Elwell +--- + drivers/video/fbdev/bcm2708_fb.c | 5 ++--- + 1 file changed, 2 insertions(+), 3 deletions(-) + +--- a/drivers/video/fbdev/bcm2708_fb.c ++++ b/drivers/video/fbdev/bcm2708_fb.c +@@ -1092,10 +1092,9 @@ static int bcm2708_fb_probe(struct platf + * set one display + */ + if (ret || num_displays == 0) { +- num_displays = 1; + dev_err(&dev->dev, +- "Unable to determine number of FB's. Assuming 1\n"); +- ret = 0; ++ "Unable to determine number of FBs. Disabling driver.\n"); ++ return -ENOENT; + } else { + fbdev->firmware_supports_multifb = 1; + } diff --git a/target/linux/bcm27xx/patches-5.10/950-0244-dt-bindings-media-i2c-Add-IMX477-CMOS-sensor-binding.patch b/target/linux/bcm27xx/patches-5.10/950-0244-dt-bindings-media-i2c-Add-IMX477-CMOS-sensor-binding.patch new file mode 100644 index 0000000000..0326c85515 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0244-dt-bindings-media-i2c-Add-IMX477-CMOS-sensor-binding.patch @@ -0,0 +1,130 @@ +From f312f497a22b3a69640d628277f5c56238860bc3 Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Thu, 7 May 2020 15:50:54 +0100 +Subject: [PATCH] dt-bindings: media: i2c: Add IMX477 CMOS sensor + binding + +Add YAML device tree binding for IMX477 CMOS image sensor. + +Signed-off-by: Naushir Patuck +--- + .../devicetree/bindings/media/i2c/imx477.yaml | 113 ++++++++++++++++++ + 1 file changed, 113 insertions(+) + create mode 100644 Documentation/devicetree/bindings/media/i2c/imx477.yaml + +--- /dev/null ++++ b/Documentation/devicetree/bindings/media/i2c/imx477.yaml +@@ -0,0 +1,113 @@ ++# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) ++%YAML 1.2 ++--- ++$id: http://devicetree.org/schemas/media/i2c/imx477.yaml# ++$schema: http://devicetree.org/meta-schemas/core.yaml# ++ ++title: Sony 1/2.3-Inch 12Mpixel CMOS Digital Image Sensor ++ ++maintainers: ++ - Naushir Patuck ++ ++description: |- ++ The Sony IMX477 is a 1/2.3-inch CMOS active pixel digital image sensor ++ with an active array size of 4056H x 3040V. It is programmable through ++ I2C interface. The I2C address is fixed to 0x1A as per sensor data sheet. ++ Image data is sent through MIPI CSI-2, which is configured as either 2 or ++ 4 data lanes. ++ ++properties: ++ compatible: ++ const: sony,imx477 ++ ++ reg: ++ description: I2C device address ++ maxItems: 1 ++ ++ clocks: ++ maxItems: 1 ++ ++ VDIG-supply: ++ description: ++ Digital I/O voltage supply, 1.05 volts ++ ++ VANA-supply: ++ description: ++ Analog voltage supply, 2.8 volts ++ ++ VDDL-supply: ++ description: ++ Digital core voltage supply, 1.8 volts ++ ++ reset-gpios: ++ description: |- ++ Reference to the GPIO connected to the xclr pin, if any. ++ Must be released (set high) after all all supplies and INCK are applied. ++ ++ # See ../video-interfaces.txt for more details ++ port: ++ type: object ++ properties: ++ endpoint: ++ type: object ++ properties: ++ data-lanes: ++ description: |- ++ The sensor supports either two-lane, or four-lane operation. ++ For two-lane operation the property must be set to <1 2>. ++ items: ++ - const: 1 ++ - const: 2 ++ ++ clock-noncontinuous: ++ type: boolean ++ description: |- ++ MIPI CSI-2 clock is non-continuous if this property is present, ++ otherwise it's continuous. ++ ++ link-frequencies: ++ allOf: ++ - $ref: /schemas/types.yaml#/definitions/uint64-array ++ description: ++ Allowed data bus frequencies. ++ ++ required: ++ - link-frequencies ++ ++required: ++ - compatible ++ - reg ++ - clocks ++ - VANA-supply ++ - VDIG-supply ++ - VDDL-supply ++ - port ++ ++additionalProperties: false ++ ++examples: ++ - | ++ i2c0 { ++ #address-cells = <1>; ++ #size-cells = <0>; ++ ++ imx477: sensor@10 { ++ compatible = "sony,imx477"; ++ reg = <0x1a>; ++ clocks = <&imx477_clk>; ++ VANA-supply = <&imx477_vana>; /* 2.8v */ ++ VDIG-supply = <&imx477_vdig>; /* 1.05v */ ++ VDDL-supply = <&imx477_vddl>; /* 1.8v */ ++ ++ port { ++ imx477_0: endpoint { ++ remote-endpoint = <&csi1_ep>; ++ data-lanes = <1 2>; ++ clock-noncontinuous; ++ link-frequencies = /bits/ 64 <450000000>; ++ }; ++ }; ++ }; ++ }; ++ ++... diff --git a/target/linux/bcm27xx/patches-5.10/950-0245-media-bcm2835-unicam-Always-service-interrupts.patch b/target/linux/bcm27xx/patches-5.10/950-0245-media-bcm2835-unicam-Always-service-interrupts.patch new file mode 100644 index 0000000000..f863e4694f --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0245-media-bcm2835-unicam-Always-service-interrupts.patch @@ -0,0 +1,51 @@ +From 320838e297c604a51ae37e6e55983c880ced9f42 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 13 May 2020 18:28:27 +0100 +Subject: [PATCH] media: bcm2835-unicam: Always service interrupts + +From when bringing up the driver, there was a check in the isr +to ignore interrupts (claiming them handled) should the driver +not be streaming. + +The VPU now will not register a camera driver if it finds a +CSI2 node enabled in device tree, therefore this flawed check is +redundant. + +https://github.com/raspberrypi/linux/issues/3602 + +Signed-off-by: Dave Stevenson +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 15 --------------- + 1 file changed, 15 deletions(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -766,12 +766,6 @@ static int unicam_all_nodes_streaming(st + return ret; + } + +-static int unicam_all_nodes_disabled(struct unicam_device *dev) +-{ +- return !dev->node[IMAGE_PAD].streaming && +- !dev->node[METADATA_PAD].streaming; +-} +- + static void unicam_queue_event_sof(struct unicam_device *unicam) + { + struct v4l2_event event = { +@@ -801,15 +795,6 @@ static irqreturn_t unicam_isr(int irq, v + u64 ts; + int i; + +- /* +- * Don't service interrupts if not streaming. +- * Avoids issues if the VPU should enable the +- * peripheral without the kernel knowing (that +- * shouldn't happen, but causes issues if it does). +- */ +- if (unicam_all_nodes_disabled(unicam)) +- return IRQ_HANDLED; +- + sta = reg_read(cfg, UNICAM_STA); + /* Write value back to clear the interrupts */ + reg_write(cfg, UNICAM_STA, sta); diff --git a/target/linux/bcm27xx/patches-5.10/950-0246-sc16is7xx-Fix-for-hardware-flow-control.patch b/target/linux/bcm27xx/patches-5.10/950-0246-sc16is7xx-Fix-for-hardware-flow-control.patch new file mode 100644 index 0000000000..aeabd97257 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0246-sc16is7xx-Fix-for-hardware-flow-control.patch @@ -0,0 +1,70 @@ +From 287fbc1b38d530aef3bc66420db7591808ff9969 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 13 May 2020 20:10:15 +0100 +Subject: [PATCH] sc16is7xx: Fix for hardware flow control + +The SC16IS7XX hardware flow control is mishandled by the driver in +a number of ways: + + 1. The set_baud method accidentally clears it when setting EFR bit. + 2. Even though hardware flow control is enabled, it isn't indicated + back to the serial framework. + 3. Applying the flow control clears the EFR bit. + 4. The CTS support is not indicated in the return from + sc16is7xx_get_mctrl. + +Address all of those issues using a mixture of patches found on the +linked pages. + +See: https://github.com/raspberrypi/linux/issues/2542 +See: https://www.spinics.net/lists/linux-serial/msg21794.html + +Signed-off-by: Phil Elwell +--- + drivers/tty/serial/sc16is7xx.c | 14 ++++++++++---- + 1 file changed, 10 insertions(+), 4 deletions(-) + +--- a/drivers/tty/serial/sc16is7xx.c ++++ b/drivers/tty/serial/sc16is7xx.c +@@ -523,8 +523,9 @@ static int sc16is7xx_set_baud(struct uar + + /* Enable enhanced features */ + regcache_cache_bypass(s->regmap, true); +- sc16is7xx_port_write(port, SC16IS7XX_EFR_REG, +- SC16IS7XX_EFR_ENABLE_BIT); ++ sc16is7xx_port_update(port, SC16IS7XX_EFR_REG, ++ SC16IS7XX_EFR_ENABLE_BIT, ++ SC16IS7XX_EFR_ENABLE_BIT); + regcache_cache_bypass(s->regmap, false); + + /* Put LCR back to the normal mode */ +@@ -839,7 +840,7 @@ static unsigned int sc16is7xx_get_mctrl( + /* DCD and DSR are not wired and CTS/RTS is handled automatically + * so just indicate DSR and CAR asserted + */ +- return TIOCM_DSR | TIOCM_CAR; ++ return TIOCM_DSR | TIOCM_CAR | TIOCM_RI | TIOCM_CTS; + } + + static void sc16is7xx_set_mctrl(struct uart_port *port, unsigned int mctrl) +@@ -926,14 +927,19 @@ static void sc16is7xx_set_termios(struct + regcache_cache_bypass(s->regmap, true); + sc16is7xx_port_write(port, SC16IS7XX_XON1_REG, termios->c_cc[VSTART]); + sc16is7xx_port_write(port, SC16IS7XX_XOFF1_REG, termios->c_cc[VSTOP]); +- if (termios->c_cflag & CRTSCTS) ++ if (termios->c_cflag & CRTSCTS) { + flow |= SC16IS7XX_EFR_AUTOCTS_BIT | + SC16IS7XX_EFR_AUTORTS_BIT; ++ port->status |= UPSTAT_AUTOCTS; ++ }; + if (termios->c_iflag & IXON) + flow |= SC16IS7XX_EFR_SWFLOW3_BIT; + if (termios->c_iflag & IXOFF) + flow |= SC16IS7XX_EFR_SWFLOW1_BIT; + ++ /* Always set enable enhanced */ ++ flow |= SC16IS7XX_EFR_ENABLE_BIT; ++ + sc16is7xx_port_write(port, SC16IS7XX_EFR_REG, flow); + regcache_cache_bypass(s->regmap, false); + diff --git a/target/linux/bcm27xx/patches-5.10/950-0247-staging-vc04_services-mmal-vchiq-Update-parameters-l.patch b/target/linux/bcm27xx/patches-5.10/950-0247-staging-vc04_services-mmal-vchiq-Update-parameters-l.patch new file mode 100644 index 0000000000..3a113a1d3f --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0247-staging-vc04_services-mmal-vchiq-Update-parameters-l.patch @@ -0,0 +1,28 @@ +From c50cbae8ecdd826ce9b710ce405ff8b459b0b781 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Fri, 15 May 2020 13:42:10 +0100 +Subject: [PATCH] staging: vc04_services: mmal-vchiq: Update parameters + list + +Adds in a couple of new MMAL parameter defines. + +Signed-off-by: Dave Stevenson +--- + drivers/staging/vc04_services/vchiq-mmal/mmal-parameters.h | 6 ++++++ + 1 file changed, 6 insertions(+) + +--- a/drivers/staging/vc04_services/vchiq-mmal/mmal-parameters.h ++++ b/drivers/staging/vc04_services/vchiq-mmal/mmal-parameters.h +@@ -612,6 +612,12 @@ enum mmal_parameter_video_type { + + /**< Takes a @ref MMAL_PARAMETER_UINT32_T */ + MMAL_PARAMETER_VIDEO_DROPPABLE_PFRAME_LENGTH, ++ ++ /**< Take a @ref MMAL_PARAMETER_VIDEO_STALL_T */ ++ MMAL_PARAMETER_VIDEO_STALL_THRESHOLD, ++ ++ /**< Take a @ref MMAL_PARAMETER_BOOLEAN_T */ ++ MMAL_PARAMETER_VIDEO_ENCODE_HEADERS_WITH_FRAME, + }; + + /** Valid mirror modes */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0248-staging-vc04_services-bcm2835-camera-Request-headers.patch b/target/linux/bcm27xx/patches-5.10/950-0248-staging-vc04_services-bcm2835-camera-Request-headers.patch new file mode 100644 index 0000000000..a2efc1d214 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0248-staging-vc04_services-bcm2835-camera-Request-headers.patch @@ -0,0 +1,30 @@ +From 1f0594a0dedb69f45c414fb05683921ef79b65b9 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Fri, 15 May 2020 13:48:59 +0100 +Subject: [PATCH] staging:vc04_services: bcm2835-camera: Request + headers with I-frame + +V4L2 wishes to have the codec header bytes in the same buffer as the +first encoded frame, so it does become 1-in 1-out for encoding. +The firmware now has an option to do this, so enable it. + +Signed-off-by: Dave Stevenson +--- + .../staging/vc04_services/bcm2835-camera/bcm2835-camera.c | 6 ++++++ + 1 file changed, 6 insertions(+) + +--- a/drivers/staging/vc04_services/bcm2835-camera/bcm2835-camera.c ++++ b/drivers/staging/vc04_services/bcm2835-camera/bcm2835-camera.c +@@ -1734,6 +1734,12 @@ static int mmal_init(struct bm2835_mmal_ + MMAL_PARAMETER_MINIMISE_FRAGMENTATION, + &enable, + sizeof(enable)); ++ ++ /* Enable inserting headers into the first frame */ ++ vchiq_mmal_port_parameter_set(dev->instance, ++ &dev->component[COMP_VIDEO_ENCODE]->control, ++ MMAL_PARAMETER_VIDEO_ENCODE_HEADERS_WITH_FRAME, ++ &enable, sizeof(enable)); + } + ret = bm2835_mmal_set_all_camera_controls(dev); + if (ret < 0) { diff --git a/target/linux/bcm27xx/patches-5.10/950-0249-kbuild-Disable-gcc-plugins.patch b/target/linux/bcm27xx/patches-5.10/950-0249-kbuild-Disable-gcc-plugins.patch new file mode 100644 index 0000000000..f3a0b33a92 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0249-kbuild-Disable-gcc-plugins.patch @@ -0,0 +1,28 @@ +From 4c6ffdf90a3a982fa11676faf658eebfd000867b Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 8 Apr 2020 15:23:56 +0100 +Subject: [PATCH] kbuild: Disable gcc plugins + +The GCC plugin feature leads to different kernel configurations on what +ought to be equivalent build systems because they depend on the build +hosts native compilers rather than the cross compilers needed for the +target. This causes problems with module symbol version mismatches. + +Disable GCC plugins for all build hosts. + +Advanced build script hackery borrowed from a patch by milhouse. + +Signed-off-by: Phil Elwell +--- + scripts/gcc-plugin.sh | 1 + + 1 file changed, 1 insertion(+) + +--- a/scripts/gcc-plugin.sh ++++ b/scripts/gcc-plugin.sh +@@ -1,5 +1,6 @@ + #!/bin/sh + # SPDX-License-Identifier: GPL-2.0 ++exit 1 # Disable plugins + + set -e + diff --git a/target/linux/bcm27xx/patches-5.10/950-0250-media-bcm2835-unicam-Retain-packing-information-on-G.patch b/target/linux/bcm27xx/patches-5.10/950-0250-media-bcm2835-unicam-Retain-packing-information-on-G.patch new file mode 100644 index 0000000000..0c94a803ff --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0250-media-bcm2835-unicam-Retain-packing-information-on-G.patch @@ -0,0 +1,48 @@ +From 9e8d2ff820bdc215ea0d06feb3fd95960cbeda6f Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 19 May 2020 11:46:47 +0100 +Subject: [PATCH] media: bcm2835-unicam: Retain packing information on + G_FMT + +The change to retrieve the pixel format always on g_fmt didn't +check whether the native or unpacked version of the format +had been requested, and always returned the packed one. +Correct this so that the packing setting is retained whereever +possible. + +Fixes "9d59e89 media: bcm2835-unicam: Re-fetch mbus code from subdev +on a g_fmt call" + +Signed-off-by: Dave Stevenson +--- + .../media/platform/bcm2835/bcm2835-unicam.c | 19 +++++++++++++++++-- + 1 file changed, 17 insertions(+), 2 deletions(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -974,8 +974,23 @@ static int unicam_g_fmt_vid_cap(struct f + if (!fmt) + return -EINVAL; + +- node->fmt = fmt; +- node->v_fmt.fmt.pix.pixelformat = fmt->fourcc; ++ if (node->fmt != fmt) { ++ /* ++ * The sensor format has changed so the pixelformat needs to ++ * be updated. Try and retain the packed/unpacked choice if ++ * at all possible. ++ */ ++ if (node->fmt->repacked_fourcc == ++ node->v_fmt.fmt.pix.pixelformat) ++ /* Using the repacked format */ ++ node->v_fmt.fmt.pix.pixelformat = fmt->repacked_fourcc; ++ else ++ /* Using the native format */ ++ node->v_fmt.fmt.pix.pixelformat = fmt->fourcc; ++ ++ node->fmt = fmt; ++ } ++ + *f = node->v_fmt; + + return 0; diff --git a/target/linux/bcm27xx/patches-5.10/950-0251-zswap-Defer-zswap-initialisation.patch b/target/linux/bcm27xx/patches-5.10/950-0251-zswap-Defer-zswap-initialisation.patch new file mode 100644 index 0000000000..111d7dcfc3 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0251-zswap-Defer-zswap-initialisation.patch @@ -0,0 +1,125 @@ +From 164ec4ae01c28cd627d085c19f5e1c631b4cccff Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 5 May 2020 15:23:32 +0100 +Subject: [PATCH] zswap: Defer zswap initialisation + +Enabling zswap support in the kernel configuration costs about 1.5MB +of RAM, even when zswap is not enabled at runtime. This cost can be +reduced significantly by deferring initialisation (including pool +creation) until the "enabled" parameter is set to true. There is a +small cost to this in that some initialisation code has to remain in +memory after the init phase, just in case they are needed later, +but the total size increase is negligible. + +See: https://github.com/raspberrypi/linux/pull/3432 + +Signed-off-by: Phil Elwell +--- + mm/zswap.c | 53 +++++++++++++++++++++++++++++------------------------ + 1 file changed, 29 insertions(+), 24 deletions(-) + +--- a/mm/zswap.c ++++ b/mm/zswap.c +@@ -592,8 +592,9 @@ error: + return NULL; + } + +-static __init struct zswap_pool *__zswap_pool_create_fallback(void) ++static bool zswap_try_pool_create(void) + { ++ struct zswap_pool *pool; + bool has_comp, has_zpool; + + has_comp = crypto_has_comp(zswap_compressor, 0, 0); +@@ -629,9 +630,21 @@ static __init struct zswap_pool *__zswap + } + + if (!has_comp || !has_zpool) +- return NULL; ++ return false; ++ ++ pool = zswap_pool_create(zswap_zpool_type, zswap_compressor); + +- return zswap_pool_create(zswap_zpool_type, zswap_compressor); ++ if (pool) { ++ pr_info("loaded using pool %s/%s\n", pool->tfm_name, ++ zpool_get_type(pool->zpool)); ++ list_add(&pool->list, &zswap_pools); ++ zswap_has_pool = true; ++ } else { ++ pr_err("pool creation failed\n"); ++ zswap_enabled = false; ++ } ++ ++ return zswap_enabled; + } + + static void zswap_pool_destroy(struct zswap_pool *pool) +@@ -804,16 +817,19 @@ static int zswap_zpool_param_set(const c + static int zswap_enabled_param_set(const char *val, + const struct kernel_param *kp) + { ++ int ret; ++ + if (zswap_init_failed) { + pr_err("can't enable, initialization failed\n"); + return -ENODEV; + } +- if (!zswap_has_pool && zswap_init_started) { +- pr_err("can't enable, no pool configured\n"); +- return -ENODEV; +- } + +- return param_set_bool(val, kp); ++ ret = param_set_bool(val, kp); ++ if (!ret && zswap_enabled && zswap_init_started && !zswap_has_pool) ++ if (!zswap_try_pool_create()) ++ ret = -ENODEV; ++ ++ return ret; + } + + /********************************* +@@ -1314,7 +1330,6 @@ static void __exit zswap_debugfs_exit(vo + **********************************/ + static int __init init_zswap(void) + { +- struct zswap_pool *pool; + int ret; + + zswap_init_started = true; +@@ -1338,29 +1353,19 @@ static int __init init_zswap(void) + if (ret) + goto hp_fail; + +- pool = __zswap_pool_create_fallback(); +- if (pool) { +- pr_info("loaded using pool %s/%s\n", pool->tfm_name, +- zpool_get_type(pool->zpool)); +- list_add(&pool->list, &zswap_pools); +- zswap_has_pool = true; +- } else { +- pr_err("pool creation failed\n"); +- zswap_enabled = false; +- } +- + shrink_wq = create_workqueue("zswap-shrink"); + if (!shrink_wq) +- goto fallback_fail; ++ goto hp_fail; + + frontswap_register_ops(&zswap_frontswap_ops); + if (zswap_debugfs_init()) + pr_warn("debugfs initialization failed\n"); ++ ++ if (zswap_enabled) ++ zswap_try_pool_create(); ++ + return 0; + +-fallback_fail: +- if (pool) +- zswap_pool_destroy(pool); + hp_fail: + cpuhp_remove_state(CPUHP_MM_ZSWP_MEM_PREPARE); + dstmem_fail: diff --git a/target/linux/bcm27xx/patches-5.10/950-0252-SQUASH-pinctrl-bcm2835-Set-base-for-bcm2711-GPIO-to-.patch b/target/linux/bcm27xx/patches-5.10/950-0252-SQUASH-pinctrl-bcm2835-Set-base-for-bcm2711-GPIO-to-.patch new file mode 100644 index 0000000000..95ced63872 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0252-SQUASH-pinctrl-bcm2835-Set-base-for-bcm2711-GPIO-to-.patch @@ -0,0 +1,27 @@ +From abc82e964df6c13999cff7b148b12efb255f19aa Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Fri, 22 May 2020 11:35:33 +0100 +Subject: [PATCH] SQUASH: pinctrl: bcm2835: Set base for bcm2711 GPIO + to 0 + +Without this patch GPIOs don't seem to work properly, primarily +noticeable as broken LEDs. + +Squash with "pinctrl-bcm2835: Set base to 0 give expected gpio numbering" + +Signed-off-by: Phil Elwell +--- + drivers/pinctrl/bcm/pinctrl-bcm2835.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/pinctrl/bcm/pinctrl-bcm2835.c ++++ b/drivers/pinctrl/bcm/pinctrl-bcm2835.c +@@ -378,7 +378,7 @@ static const struct gpio_chip bcm2711_gp + .get = bcm2835_gpio_get, + .set = bcm2835_gpio_set, + .set_config = gpiochip_generic_config, +- .base = -1, ++ .base = 0, + .ngpio = BCM2711_NUM_GPIOS, + .can_sleep = false, + }; diff --git a/target/linux/bcm27xx/patches-5.10/950-0253-staging-vchiq_arm-Clean-up-40-bit-DMA-support.patch b/target/linux/bcm27xx/patches-5.10/950-0253-staging-vchiq_arm-Clean-up-40-bit-DMA-support.patch new file mode 100644 index 0000000000..b9d4c1701b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0253-staging-vchiq_arm-Clean-up-40-bit-DMA-support.patch @@ -0,0 +1,174 @@ +From 461092c036303037c0efe37002079ce6e9ed8ba5 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 20 May 2020 16:36:33 +0100 +Subject: [PATCH] staging: vchiq_arm: Clean up 40-bit DMA support + +Manage the split between addresses for the VPU and addresses for the +40-bit DMA controller with a dedicated DMA device pointer that on non- +BCM2711 platforms is the same as the main VCHIQ device. This allows +the VCHIQ node to stay in the usual place in the DT, and removes the +ugly VC_SAFE macros. + +Signed-off-by: Phil Elwell + +staging: vchiq_arm: Use g_dma_dev for dma_unmap_sg + +Commit "staging: vchiq_arm: Clean up 40-bit DMA support" failed to +change one of the calls to dma_unmap_sg to pass in g_dma_dev (rather +than g_dev). Correct that oversight. + +See: https://github.com/raspberrypi/linux/issues/3647 + +Signed-off-by: Phil Elwell +--- + .../interface/vchiq_arm/vchiq_2835_arm.c | 42 ++++++++++++------- + .../interface/vchiq_arm/vchiq_arm.c | 14 ------- + 2 files changed, 27 insertions(+), 29 deletions(-) + +--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_2835_arm.c ++++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_2835_arm.c +@@ -16,8 +16,6 @@ + #include + + #define TOTAL_SLOTS (VCHIQ_SLOT_ZERO_SLOTS + 2 * 32) +-#define VC_SAFE(x) (g_use_36bit_addrs ? ((u32)(x) | 0xc0000000) : (u32)(x)) +-#define IS_VC_SAFE(x) (g_use_36bit_addrs ? !((x) & ~0x3fffffffull) : 1) + + #include "vchiq_arm.h" + #include "vchiq_connected.h" +@@ -66,6 +64,7 @@ static char *g_fragments_base; + static char *g_free_fragments; + static struct semaphore g_free_fragments_sema; + static struct device *g_dev; ++static struct device *g_dma_dev; + + static DEFINE_SEMAPHORE(g_free_fragments_mutex); + +@@ -82,6 +81,7 @@ free_pagelist(struct vchiq_pagelist_info + int vchiq_platform_init(struct platform_device *pdev, struct vchiq_state *state) + { + struct device *dev = &pdev->dev; ++ struct device *dma_dev = NULL; + struct vchiq_drvdata *drvdata = platform_get_drvdata(pdev); + struct rpi_firmware *fw = drvdata->fw; + struct vchiq_slot_zero *vchiq_slot_zero; +@@ -103,7 +103,23 @@ int vchiq_platform_init(struct platform_ + g_cache_line_size = drvdata->cache_line_size; + g_fragments_size = 2 * g_cache_line_size; + +- g_use_36bit_addrs = (dev->dma_pfn_offset == 0); ++ if (drvdata->use_36bit_addrs) { ++ struct device_node *dma_node = ++ of_find_compatible_node(NULL, NULL, "brcm,bcm2711-dma"); ++ ++ if (dma_node) { ++ struct platform_device *pdev; ++ ++ pdev = of_find_device_by_node(dma_node); ++ if (pdev) ++ dma_dev = &pdev->dev; ++ of_node_put(dma_node); ++ g_use_36bit_addrs = true; ++ } else { ++ dev_err(dev, "40-bit DMA controller not found\n"); ++ return -EINVAL; ++ } ++ } + + /* Allocate space for the channels in coherent memory */ + slot_mem_size = PAGE_ALIGN(TOTAL_SLOTS * VCHIQ_SLOT_SIZE); +@@ -116,14 +132,8 @@ int vchiq_platform_init(struct platform_ + return -ENOMEM; + } + +- if (!IS_VC_SAFE(slot_phys)) { +- dev_err(dev, "allocated DMA memory %pad is not VC-safe\n", +- &slot_phys); +- return -ENOMEM; +- } +- + WARN_ON(((unsigned long)slot_mem & (PAGE_SIZE - 1)) != 0); +- channelbase = VC_SAFE(slot_phys); ++ channelbase = slot_phys; + + vchiq_slot_zero = vchiq_init_slots(slot_mem, slot_mem_size); + if (!vchiq_slot_zero) +@@ -171,6 +181,8 @@ int vchiq_platform_init(struct platform_ + } + + g_dev = dev; ++ g_dma_dev = dma_dev ?: dev; ++ + vchiq_log_info(vchiq_arm_log_level, + "vchiq_init - done (slots %pK, phys %pad)", + vchiq_slot_zero, &slot_phys); +@@ -240,7 +252,7 @@ vchiq_prepare_bulk_data(struct vchiq_bul + if (!pagelistinfo) + return VCHIQ_ERROR; + +- bulk->data = (void *)VC_SAFE(pagelistinfo->dma_addr); ++ bulk->data = pagelistinfo->dma_addr; + + /* + * Store the pagelistinfo address in remote_data, +@@ -295,7 +307,7 @@ static void + cleanup_pagelistinfo(struct vchiq_pagelist_info *pagelistinfo) + { + if (pagelistinfo->scatterlist_mapped) { +- dma_unmap_sg(g_dev, pagelistinfo->scatterlist, ++ dma_unmap_sg(g_dma_dev, pagelistinfo->scatterlist, + pagelistinfo->num_pages, pagelistinfo->dma_dir); + } + +@@ -444,7 +456,7 @@ create_pagelist(char *buf, char __user * + count -= len; + } + +- dma_buffers = dma_map_sg(g_dev, ++ dma_buffers = dma_map_sg(g_dma_dev, + scatterlist, + num_pages, + pagelistinfo->dma_dir); +@@ -494,7 +506,7 @@ create_pagelist(char *buf, char __user * + } else { + for_each_sg(scatterlist, sg, dma_buffers, i) { + u32 len = sg_dma_len(sg); +- u32 addr = VC_SAFE(sg_dma_address(sg)); ++ u32 addr = sg_dma_address(sg); + u32 new_pages = (len + PAGE_SIZE - 1) >> PAGE_SHIFT; + + /* Note: addrs is the address + page_count - 1 +@@ -555,7 +567,7 @@ free_pagelist(struct vchiq_pagelist_info + * NOTE: dma_unmap_sg must be called before the + * cpu can touch any of the data/pages. + */ +- dma_unmap_sg(g_dev, pagelistinfo->scatterlist, ++ dma_unmap_sg(g_dma_dev, pagelistinfo->scatterlist, + pagelistinfo->num_pages, pagelistinfo->dma_dir); + pagelistinfo->scatterlist_mapped = 0; + +--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c ++++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c +@@ -2720,22 +2720,8 @@ vchiq_register_child(struct platform_dev + + child->dev.of_node = np; + +- /* +- * We want the dma-ranges etc to be copied from a device with the +- * correct dma-ranges for the VPU. +- * VCHIQ on Pi4 is now under scb which doesn't get those dma-ranges. +- * Take the "dma" node as going to be suitable as it sees the world +- * through the same eyes as the VPU. +- */ +- np = of_find_node_by_path("dma"); +- if (!np) +- np = pdev->dev.of_node; +- + of_dma_configure(&child->dev, np, true); + +- if (np != pdev->dev.of_node) +- of_node_put(np); +- + return child; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0254-media-bcm2835-unicam-change-minimum-number-of-vb2_qu.patch b/target/linux/bcm27xx/patches-5.10/950-0254-media-bcm2835-unicam-change-minimum-number-of-vb2_qu.patch new file mode 100644 index 0000000000..6421bcfc76 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0254-media-bcm2835-unicam-change-minimum-number-of-vb2_qu.patch @@ -0,0 +1,28 @@ +From f858ff156427e99d5abeebc80c666caab33b3637 Mon Sep 17 00:00:00 2001 +From: David Plowman +Date: Thu, 28 May 2020 11:09:48 +0100 +Subject: [PATCH] media: bcm2835-unicam: change minimum number of + vb2_queue buffers to 1 + +Since the unicam driver was modified to write to a dummy buffer when no +user-supplied buffer is available, it can now write to and return a +buffer even when there's only a single one. Enable this by changing the +min_buffers_needed in the vb2_queue; it will be useful for enabling +still captures without allocating more memory than absolutely necessary. + +Signed-off-by: David Plowman +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -2404,7 +2404,7 @@ static int register_node(struct unicam_d + q->buf_struct_size = sizeof(struct unicam_buffer); + q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC; + q->lock = &node->lock; +- q->min_buffers_needed = 2; ++ q->min_buffers_needed = 1; + q->dev = &unicam->pdev->dev; + + ret = vb2_queue_init(q); diff --git a/target/linux/bcm27xx/patches-5.10/950-0255-snd_bcm2835-disable-HDMI-audio-when-vc4-is-used-3640.patch b/target/linux/bcm27xx/patches-5.10/950-0255-snd_bcm2835-disable-HDMI-audio-when-vc4-is-used-3640.patch new file mode 100644 index 0000000000..50eccbfbd9 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0255-snd_bcm2835-disable-HDMI-audio-when-vc4-is-used-3640.patch @@ -0,0 +1,33 @@ +From d9d1244f8aa9d776073e2a12e0cb9542d89bd3cb Mon Sep 17 00:00:00 2001 +From: Hristo Venev +Date: Fri, 5 Jun 2020 09:22:49 +0000 +Subject: [PATCH] snd_bcm2835: disable HDMI audio when vc4 is used + (#3640) + +Things don't work too well when both the vc4 driver and the firmware +driver are trying to control the same audio output: + +[ 763.569406] bcm2835_audio bcm2835_audio: vchi message timeout, msg=5 + +Hence, when the vc4 HDMI driver is used, let it control audio. This is done +by introducing a new device tree property to the audio node, and +extending the vc4-kms-v3d overlays to set it appropriately. + +Signed-off-by: Hristo Venev +--- + drivers/staging/vc04_services/bcm2835-audio/bcm2835.c | 4 +++- + 1 file changed, 3 insertions(+), 1 deletion(-) + +--- a/drivers/staging/vc04_services/bcm2835-audio/bcm2835.c ++++ b/drivers/staging/vc04_services/bcm2835-audio/bcm2835.c +@@ -381,7 +381,9 @@ static int snd_bcm2835_alsa_probe(struct + } + + if (!enable_compat_alsa) { +- set_hdmi_enables(dev); ++ if (!of_property_read_bool(dev->of_node, "brcm,disable-hdmi")) ++ set_hdmi_enables(dev); ++ + // In this mode, always enable analog output + enable_headphones = true; + } else { diff --git a/target/linux/bcm27xx/patches-5.10/950-0256-gpiolib-Don-t-prevent-IRQ-usage-of-output-GPIOs.patch b/target/linux/bcm27xx/patches-5.10/950-0256-gpiolib-Don-t-prevent-IRQ-usage-of-output-GPIOs.patch new file mode 100644 index 0000000000..4defea7e16 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0256-gpiolib-Don-t-prevent-IRQ-usage-of-output-GPIOs.patch @@ -0,0 +1,50 @@ +From 205dc5dbd2b1978f5c75daa0afabf0cf15c8e1fe Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 24 Apr 2018 14:42:27 +0100 +Subject: [PATCH] gpiolib: Don't prevent IRQ usage of output GPIOs + +Upstream Linux deems using output GPIOs to generate IRQs as a bogus +use case, even though the BCM2835 GPIO controller is capable of doing +so. A number of users would like to make use of this facility, so +disable the checks. + +See: https://github.com/raspberrypi/linux/issues/2527 + +Signed-off-by: Phil Elwell +--- + drivers/gpio/gpiolib.c | 10 ++++++---- + 1 file changed, 6 insertions(+), 4 deletions(-) + +--- a/drivers/gpio/gpiolib.c ++++ b/drivers/gpio/gpiolib.c +@@ -51,6 +51,8 @@ + #define extra_checks 0 + #endif + ++#define dont_test_bit(b,d) (0) ++ + /* Device and char device-related information */ + static DEFINE_IDA(gpio_ida); + static dev_t gpio_devt; +@@ -2444,8 +2446,8 @@ int gpiod_direction_output(struct gpio_d + value = !!value; + + /* GPIOs used for enabled IRQs shall not be set as output */ +- if (test_bit(FLAG_USED_AS_IRQ, &desc->flags) && +- test_bit(FLAG_IRQ_IS_ENABLED, &desc->flags)) { ++ if (dont_test_bit(FLAG_USED_AS_IRQ, &desc->flags) && ++ dont_test_bit(FLAG_IRQ_IS_ENABLED, &desc->flags)) { + gpiod_err(desc, + "%s: tried to set a GPIO tied to an IRQ as output\n", + __func__); +@@ -3250,8 +3252,8 @@ int gpiochip_lock_as_irq(struct gpio_chi + } + + /* To be valid for IRQ the line needs to be input or open drain */ +- if (test_bit(FLAG_IS_OUT, &desc->flags) && +- !test_bit(FLAG_OPEN_DRAIN, &desc->flags)) { ++ if (dont_test_bit(FLAG_IS_OUT, &desc->flags) && ++ !dont_test_bit(FLAG_OPEN_DRAIN, &desc->flags)) { + chip_err(gc, + "%s: tried to flag a GPIO set as output for IRQ\n", + __func__); diff --git a/target/linux/bcm27xx/patches-5.10/950-0257-PCI-brcmstb-Add-DT-property-to-control-L1SS.patch b/target/linux/bcm27xx/patches-5.10/950-0257-PCI-brcmstb-Add-DT-property-to-control-L1SS.patch new file mode 100644 index 0000000000..77c2239a5d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0257-PCI-brcmstb-Add-DT-property-to-control-L1SS.patch @@ -0,0 +1,79 @@ +From 9bb199ebcdb864f9ec5df0e168df4a25820482ea Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 11 Jun 2020 09:57:03 +0100 +Subject: [PATCH] PCI: brcmstb: Add DT property to control L1SS + +The BRCM PCIe block has controls to enable control of the CLKREQ# +signal by the L1SS, and to gate the refclk with the CLKREQ# input. +These controls are mutually exclusive - the upstream code sets the +latter, but some use cases require the former. + +Add a Device Tree property - brcm,enable-l1ss - to switch to the +L1SS configuration. + +Signed-off-by: Phil Elwell +--- + drivers/pci/controller/pcie-brcmstb.c | 30 ++++++++++++++++++++------- + 1 file changed, 23 insertions(+), 7 deletions(-) + +--- a/drivers/pci/controller/pcie-brcmstb.c ++++ b/drivers/pci/controller/pcie-brcmstb.c +@@ -114,8 +114,9 @@ + PCIE_MISC_CPU_2_PCIE_MEM_WIN0_LIMIT_HI + ((win) * 8) + + #define PCIE_MISC_HARD_PCIE_HARD_DEBUG 0x4204 +-#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK 0x2 +-#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK 0x08000000 ++#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK BIT(1) ++#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_L1SS_ENABLE_MASK BIT(21) ++#define PCIE_MISC_HARD_PCIE_HARD_DEBUG_SERDES_IDDQ_MASK BIT(27) + + + #define PCIE_INTR2_CPU_BASE 0x4300 +@@ -276,6 +277,7 @@ struct brcm_pcie { + struct clk *clk; + struct device_node *np; + bool ssc; ++ bool l1ss; + int gen; + u64 msi_target_addr; + struct brcm_msi *msi; +@@ -1025,12 +1027,25 @@ static int brcm_pcie_setup(struct brcm_p + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1_ENDIAN_MODE_BAR2_MASK); + writel(tmp, base + PCIE_RC_CFG_VENDOR_VENDOR_SPECIFIC_REG1); + +- /* +- * Refclk from RC should be gated with CLKREQ# input when ASPM L0s,L1 +- * is enabled => setting the CLKREQ_DEBUG_ENABLE field to 1. +- */ + tmp = readl(base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); +- tmp |= PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK; ++ if (pcie->l1ss) { ++ /* ++ * Enable CLKREQ# signalling include L1 Substate control of ++ * the CLKREQ# signal and the external reference clock buffer. ++ * meet requirement for Endpoints that require CLKREQ# ++ * assertion to clock active within 400ns. ++ */ ++ tmp &= ~PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK; ++ tmp |= PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_L1SS_ENABLE_MASK; ++ } else { ++ /* ++ * Refclk from RC should be gated with CLKREQ# input when ++ * ASPM L0s,L1 is enabled => setting the CLKREQ_DEBUG_ENABLE ++ * field to 1. ++ */ ++ tmp &= ~PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_L1SS_ENABLE_MASK; ++ tmp |= PCIE_MISC_HARD_PCIE_HARD_DEBUG_CLKREQ_DEBUG_ENABLE_MASK; ++ } + writel(tmp, base + PCIE_MISC_HARD_PCIE_HARD_DEBUG); + + return 0; +@@ -1251,6 +1266,7 @@ static int brcm_pcie_probe(struct platfo + pcie->gen = (ret < 0) ? 0 : ret; + + pcie->ssc = of_property_read_bool(np, "brcm,enable-ssc"); ++ pcie->l1ss = of_property_read_bool(np, "brcm,enable-l1ss"); + + ret = clk_prepare_enable(pcie->clk); + if (ret) { diff --git a/target/linux/bcm27xx/patches-5.10/950-0258-media-irs1125-Using-i2c_transfer-for-ic2-reads.patch b/target/linux/bcm27xx/patches-5.10/950-0258-media-irs1125-Using-i2c_transfer-for-ic2-reads.patch new file mode 100644 index 0000000000..a9d47a6ef4 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0258-media-irs1125-Using-i2c_transfer-for-ic2-reads.patch @@ -0,0 +1,65 @@ +From 1123bcc35585a13cc25c6802f8d3968d185d7f9a Mon Sep 17 00:00:00 2001 +From: Markus Proeller +Date: Tue, 16 Jun 2020 13:24:31 +0200 +Subject: [PATCH] media: irs1125: Using i2c_transfer for ic2 reads + +Reading data over i2c is done by using i2c_transfer to ensure that this +operation can't be interrupted. + +Signed-off-by: Markus Proeller +--- + drivers/media/i2c/irs1125.c | 37 ++++++++++++++++++++++--------------- + 1 file changed, 22 insertions(+), 15 deletions(-) + +--- a/drivers/media/i2c/irs1125.c ++++ b/drivers/media/i2c/irs1125.c +@@ -248,27 +248,34 @@ static int irs1125_write(struct v4l2_sub + + static int irs1125_read(struct v4l2_subdev *sd, u16 reg, u16 *val) + { +- int ret; +- unsigned char data_w[2] = { reg >> 8, reg & 0xff }; +- char rdval[2]; +- + struct i2c_client *client = v4l2_get_subdevdata(sd); ++ struct i2c_msg msgs[2]; ++ u8 addr_buf[2] = { reg >> 8, reg & 0xff }; ++ u8 data_buf[2] = { 0, }; ++ int ret; + +- ret = i2c_master_send(client, data_w, 2); +- if (ret < 0) { +- dev_dbg(&client->dev, "%s: i2c write error, reg: %x\n", +- __func__, reg); ++ /* Write register address */ ++ msgs[0].addr = client->addr; ++ msgs[0].flags = 0; ++ msgs[0].len = ARRAY_SIZE(addr_buf); ++ msgs[0].buf = addr_buf; ++ ++ /* Read data from register */ ++ msgs[1].addr = client->addr; ++ msgs[1].flags = I2C_M_RD; ++ msgs[1].len = 2; ++ msgs[1].buf = data_buf; ++ ++ ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs)); ++ if (ret != ARRAY_SIZE(msgs)) { ++ if (ret >= 0) ++ ret = -EIO; + return ret; + } + +- ret = i2c_master_recv(client, rdval, 2); +- if (ret < 0) +- dev_err(&client->dev, "%s: i2c read error, reg: %x\n", +- __func__, reg); +- +- *val = rdval[1] | (rdval[0] << 8); ++ *val = data_buf[1] | (data_buf[0] << 8); + +- return ret; ++ return 0; + } + + static int irs1125_write_array(struct v4l2_subdev *sd, diff --git a/target/linux/bcm27xx/patches-5.10/950-0259-media-irs1125-Refactoring-and-debug-messages.patch b/target/linux/bcm27xx/patches-5.10/950-0259-media-irs1125-Refactoring-and-debug-messages.patch new file mode 100644 index 0000000000..b9aedb6546 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0259-media-irs1125-Refactoring-and-debug-messages.patch @@ -0,0 +1,123 @@ +From 77ec8aff3939654e3c5fadff77252f0c0c4cb685 Mon Sep 17 00:00:00 2001 +From: Markus Proeller +Date: Tue, 16 Jun 2020 13:27:42 +0200 +Subject: [PATCH] media: irs1125: Refactoring and debug messages + +Changed some variable names to comply with checkpatch --strict mode. +Debug messages added. + +Signed-off-by: Markus Proeller +--- + drivers/media/i2c/irs1125.c | 36 ++++++++++++++++++++---------------- + 1 file changed, 20 insertions(+), 16 deletions(-) + +--- a/drivers/media/i2c/irs1125.c ++++ b/drivers/media/i2c/irs1125.c +@@ -15,6 +15,7 @@ + #include "irs1125.h" + #include + #include ++#include + #include + #include + #include +@@ -22,13 +23,13 @@ + #include + #include + #include ++#include + #include +-#include ++#include + #include + #include + #include + #include +-#include + + #define CHECK_BIT(val, pos) ((val) & BIT(pos)) + +@@ -38,18 +39,19 @@ + + #define IRS1125_ALTERNATE_FW "irs1125_af.bin" + +-#define IRS1125_REG_CSICFG 0xA882 +-#define IRS1125_REG_DESIGN_STEP 0xB0AD +-#define IRS1125_REG_EFUSEVAL2 0xB09F +-#define IRS1125_REG_EFUSEVAL3 0xB0A0 +-#define IRS1125_REG_EFUSEVAL4 0xB0A1 +-#define IRS1125_REG_DMEM_SHADOW 0xC320 ++#define IRS1125_REG_SAFE_RECONFIG 0xA850 ++#define IRS1125_REG_CSICFG 0xA882 ++#define IRS1125_REG_DESIGN_STEP 0xB0AD ++#define IRS1125_REG_EFUSEVAL2 0xB09F ++#define IRS1125_REG_EFUSEVAL3 0xB0A0 ++#define IRS1125_REG_EFUSEVAL4 0xB0A1 ++#define IRS1125_REG_DMEM_SHADOW 0xC320 + +-#define IRS1125_DESIGN_STEP_EXPECTED 0x0a12 ++#define IRS1125_DESIGN_STEP_EXPECTED 0x0a12 + + #define IRS1125_ROW_START_DEF 0 + #define IRS1125_COLUMN_START_DEF 0 +-#define IRS1125_WINDOW_HEIGHT_DEF 288 ++#define IRS1125_WINDOW_HEIGHT_DEF 288 + #define IRS1125_WINDOW_WIDTH_DEF 352 + + struct regval_list { +@@ -87,7 +89,7 @@ static inline struct irs1125 *to_state(s + return container_of(sd, struct irs1125, sd); + } + +-static struct regval_list irs1125_26MHz[] = { ++static struct regval_list irs1125_26mhz[] = { + {0xB017, 0x0413}, + {0xB086, 0x3535}, + {0xB0AE, 0xEF02}, +@@ -153,7 +155,7 @@ static struct regval_list irs1125_26MHz[ + {0xFFFF, 100} + }; + +-static struct regval_list irs1125_seq_cfg[] = { ++static struct regval_list irs1125_seq_cfg_init[] = { + {0xC3A0, 0x823D}, + {0xC3A1, 0xB13B}, + {0xC3A2, 0x0313}, +@@ -243,6 +245,7 @@ static int irs1125_write(struct v4l2_sub + dev_err(&client->dev, "%s: i2c write error, reg: %x\n", + __func__, reg); + ++ dev_dbg(&client->dev, "write addr 0x%04x, val 0x%04x\n", reg, val); + return ret; + } + +@@ -364,8 +367,8 @@ static int __sensor_init(struct v4l2_sub + cnt++; + } + +- ret = irs1125_write_array(sd, irs1125_26MHz, +- ARRAY_SIZE(irs1125_26MHz)); ++ ret = irs1125_write_array(sd, irs1125_26mhz, ++ ARRAY_SIZE(irs1125_26mhz)); + if (ret < 0) { + dev_err(&client->dev, "write sensor default regs error\n"); + return ret; +@@ -415,8 +418,8 @@ static int __sensor_init(struct v4l2_sub + } + release_firmware(fw); + +- ret = irs1125_write_array(sd, irs1125_seq_cfg, +- ARRAY_SIZE(irs1125_seq_cfg)); ++ ret = irs1125_write_array(sd, irs1125_seq_cfg_init, ++ ARRAY_SIZE(irs1125_seq_cfg_init)); + if (ret < 0) { + dev_err(&client->dev, "write default sequence failed\n"); + return ret; +@@ -1037,6 +1040,7 @@ static int irs1125_probe(struct i2c_clie + } + + gpio_num = desc_to_gpio(sensor->reset); ++ dev_dbg(&client->dev, "reset on GPIO num %d\n", gpio_num); + + mutex_init(&sensor->lock); + diff --git a/target/linux/bcm27xx/patches-5.10/950-0260-media-irs1125-Atomic-access-to-imager-reconfiguratio.patch b/target/linux/bcm27xx/patches-5.10/950-0260-media-irs1125-Atomic-access-to-imager-reconfiguratio.patch new file mode 100644 index 0000000000..5c33c023f2 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0260-media-irs1125-Atomic-access-to-imager-reconfiguratio.patch @@ -0,0 +1,381 @@ +From aa2af4f9994e6209e4b01d259ae67afb5c87e459 Mon Sep 17 00:00:00 2001 +From: Markus Proeller +Date: Tue, 16 Jun 2020 13:31:36 +0200 +Subject: [PATCH] media: irs1125: Atomic access to imager + reconfiguration + +Instead of changing the exposure and framerate settings for all sequences, +they can be changed for every sequence individually now. Therefore the +IRS1125_CID_SAFE_RECONFIG ctrl has been removed and replaced by +IRS1125_CID_SAFE_RECONFIG_S_EXPO and *_FRAME ctrls. + +The consistency check in the sequence ctrl IRS1125_CID_SEQ_CONFIG +is removed. + +Signed-off-by: Markus Proeller +--- + drivers/media/i2c/irs1125.c | 224 ++++++++++++++++++++++++------------ + drivers/media/i2c/irs1125.h | 68 ++++++++--- + 2 files changed, 204 insertions(+), 88 deletions(-) + +--- a/drivers/media/i2c/irs1125.c ++++ b/drivers/media/i2c/irs1125.c +@@ -89,6 +89,52 @@ static inline struct irs1125 *to_state(s + return container_of(sd, struct irs1125, sd); + } + ++static const char *expo_ctrl_names[IRS1125_NUM_SEQ_ENTRIES] = { ++ "safe reconfiguration of exposure of sequence 0", ++ "safe reconfiguration of exposure of sequence 1", ++ "safe reconfiguration of exposure of sequence 2", ++ "safe reconfiguration of exposure of sequence 3", ++ "safe reconfiguration of exposure of sequence 4", ++ "safe reconfiguration of exposure of sequence 5", ++ "safe reconfiguration of exposure of sequence 6", ++ "safe reconfiguration of exposure of sequence 7", ++ "safe reconfiguration of exposure of sequence 8", ++ "safe reconfiguration of exposure of sequence 9", ++ "safe reconfiguration of exposure of sequence 10", ++ "safe reconfiguration of exposure of sequence 11", ++ "safe reconfiguration of exposure of sequence 12", ++ "safe reconfiguration of exposure of sequence 13", ++ "safe reconfiguration of exposure of sequence 14", ++ "safe reconfiguration of exposure of sequence 15", ++ "safe reconfiguration of exposure of sequence 16", ++ "safe reconfiguration of exposure of sequence 17", ++ "safe reconfiguration of exposure of sequence 18", ++ "safe reconfiguration of exposure of sequence 19", ++}; ++ ++static const char *frame_ctrl_names[IRS1125_NUM_SEQ_ENTRIES] = { ++ "safe reconfiguration of framerate of sequence 0", ++ "safe reconfiguration of framerate of sequence 1", ++ "safe reconfiguration of framerate of sequence 2", ++ "safe reconfiguration of framerate of sequence 3", ++ "safe reconfiguration of framerate of sequence 4", ++ "safe reconfiguration of framerate of sequence 5", ++ "safe reconfiguration of framerate of sequence 6", ++ "safe reconfiguration of framerate of sequence 7", ++ "safe reconfiguration of framerate of sequence 8", ++ "safe reconfiguration of framerate of sequence 9", ++ "safe reconfiguration of framerate of sequence 10", ++ "safe reconfiguration of framerate of sequence 11", ++ "safe reconfiguration of framerate of sequence 12", ++ "safe reconfiguration of framerate of sequence 13", ++ "safe reconfiguration of framerate of sequence 14", ++ "safe reconfiguration of framerate of sequence 15", ++ "safe reconfiguration of framerate of sequence 16", ++ "safe reconfiguration of framerate of sequence 17", ++ "safe reconfiguration of framerate of sequence 18", ++ "safe reconfiguration of framerate of sequence 19", ++}; ++ + static struct regval_list irs1125_26mhz[] = { + {0xB017, 0x0413}, + {0xB086, 0x3535}, +@@ -561,36 +607,57 @@ static int irs1125_s_ctrl(struct v4l2_ct + struct irs1125 *dev = container_of(ctrl->handler, + struct irs1125, ctrl_handler); + struct i2c_client *client = v4l2_get_subdevdata(&dev->sd); +- int err, i; + struct irs1125_mod_pll *mod_cur, *mod_new; +- struct irs1125_seq_cfg *cfg_cur, *cfg_new; + u16 addr, val; +- +- err = 0; ++ int err = 0, i; + + switch (ctrl->id) { +- case IRS1125_CID_SAFE_RECONFIG: +- { +- struct irs1125_illu *illu_cur, *illu_new; +- +- illu_new = (struct irs1125_illu *)ctrl->p_new.p; +- illu_cur = (struct irs1125_illu *)ctrl->p_cur.p; +- for (i = 0; i < IRS1125_NUM_SEQ_ENTRIES; i++) { +- if (illu_cur[i].exposure != illu_new[i].exposure) { +- addr = 0xA850 + i * 2; +- val = illu_new[i].exposure; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } +- if (illu_cur[i].framerate != illu_new[i].framerate) { +- addr = 0xA851 + i * 2; +- val = illu_new[i].framerate; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } +- } ++ case IRS1125_CID_SAFE_RECONFIG_S0_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S0_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S1_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S1_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S2_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S2_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S3_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S3_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S4_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S4_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S5_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S5_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S6_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S6_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S7_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S7_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S8_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S8_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S9_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S9_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S10_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S10_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S11_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S11_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S12_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S12_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S13_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S13_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S14_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S14_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S15_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S15_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S16_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S16_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S17_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S17_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S18_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S18_FRAME: ++ case IRS1125_CID_SAFE_RECONFIG_S19_EXPO: ++ case IRS1125_CID_SAFE_RECONFIG_S19_FRAME: { ++ unsigned int offset = ctrl->id - ++ IRS1125_CID_SAFE_RECONFIG_S0_EXPO; ++ ++ err = irs1125_write(&dev->sd, ++ IRS1125_REG_SAFE_RECONFIG + offset, ++ ctrl->val); + break; + } + case IRS1125_CID_MOD_PLL: +@@ -655,40 +722,40 @@ static int irs1125_s_ctrl(struct v4l2_ct + } + } + break; +- case IRS1125_CID_SEQ_CONFIG: ++ case IRS1125_CID_SEQ_CONFIG: { ++ struct irs1125_seq_cfg *cfg_new; ++ + cfg_new = (struct irs1125_seq_cfg *)ctrl->p_new.p; +- cfg_cur = (struct irs1125_seq_cfg *)ctrl->p_cur.p; + for (i = 0; i < IRS1125_NUM_SEQ_ENTRIES; i++) { +- if (cfg_cur[i].exposure != cfg_new[i].exposure) { +- addr = IRS1125_REG_DMEM_SHADOW + i * 4; +- val = cfg_new[i].exposure; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } +- if (cfg_cur[i].framerate != cfg_new[i].framerate) { +- addr = IRS1125_REG_DMEM_SHADOW + 1 + i * 4; +- val = cfg_new[i].framerate; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } +- if (cfg_cur[i].ps != cfg_new[i].ps) { +- addr = IRS1125_REG_DMEM_SHADOW + 2 + i * 4; +- val = cfg_new[i].ps; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } +- if (cfg_cur[i].pll != cfg_new[i].pll) { +- addr = IRS1125_REG_DMEM_SHADOW + 3 + i * 4; +- val = cfg_new[i].pll; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } ++ unsigned int seq_offset = i * 4; ++ u16 addr, val; ++ ++ addr = IRS1125_REG_DMEM_SHADOW + seq_offset; ++ val = cfg_new[i].exposure; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ ++ addr = IRS1125_REG_DMEM_SHADOW + 1 + seq_offset; ++ val = cfg_new[i].framerate; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ ++ addr = IRS1125_REG_DMEM_SHADOW + 2 + seq_offset; ++ val = cfg_new[i].ps; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; ++ ++ addr = IRS1125_REG_DMEM_SHADOW + 3 + seq_offset; ++ val = cfg_new[i].pll; ++ err = irs1125_write(&dev->sd, addr, val); ++ if (err < 0) ++ break; + } + break; ++ } + case IRS1125_CID_NUM_SEQS: + err = irs1125_write(&dev->sd, 0xA88D, ctrl->val - 1); + if (err >= 0) +@@ -760,19 +827,6 @@ static const struct v4l2_ctrl_config irs + IRS1125_NUM_MOD_PLLS} + }, { + .ops = &irs1125_ctrl_ops, +- .id = IRS1125_CID_SAFE_RECONFIG, +- .name = "Change exposure and pause of single seq", +- .type = V4L2_CTRL_TYPE_U16, +- .flags = V4L2_CTRL_FLAG_HAS_PAYLOAD, +- .min = 0, +- .max = U16_MAX, +- .step = 1, +- .def = 0, +- .elem_size = sizeof(u16), +- .dims = {sizeof(struct irs1125_illu) / sizeof(u16), +- IRS1125_NUM_SEQ_ENTRIES} +- }, { +- .ops = &irs1125_ctrl_ops, + .id = IRS1125_CID_SEQ_CONFIG, + .name = "Change sequence settings", + .type = V4L2_CTRL_TYPE_U16, +@@ -900,9 +954,16 @@ static int irs1125_ctrls_init(struct irs + { + struct v4l2_ctrl *ctrl; + int err, i; +- struct v4l2_ctrl_handler *hdl; ++ struct v4l2_ctrl_handler *hdl = &sensor->ctrl_handler; ++ struct v4l2_ctrl_config ctrl_cfg = { ++ .ops = &irs1125_ctrl_ops, ++ .type = V4L2_CTRL_TYPE_INTEGER, ++ .min = 0, ++ .max = U16_MAX, ++ .step = 1, ++ .def = 0x1000 ++ }; + +- hdl = &sensor->ctrl_handler; + v4l2_ctrl_handler_init(hdl, ARRAY_SIZE(irs1125_custom_ctrls)); + + for (i = 0; i < ARRAY_SIZE(irs1125_custom_ctrls); i++) { +@@ -923,6 +984,27 @@ static int irs1125_ctrls_init(struct irs + goto error_ctrls; + } + ++ for (i = 0; i < IRS1125_NUM_SEQ_ENTRIES; i++) { ++ ctrl_cfg.name = expo_ctrl_names[i]; ++ ctrl_cfg.id = IRS1125_CID_SAFE_RECONFIG_S0_EXPO + i * 2; ++ ctrl = v4l2_ctrl_new_custom(hdl, &ctrl_cfg, ++ NULL); ++ if (!ctrl) ++ dev_err(dev, "Failed to init exposure control %s\n", ++ ctrl_cfg.name); ++ } ++ ++ ctrl_cfg.def = 0; ++ for (i = 0; i < IRS1125_NUM_SEQ_ENTRIES; i++) { ++ ctrl_cfg.name = frame_ctrl_names[i]; ++ ctrl_cfg.id = IRS1125_CID_SAFE_RECONFIG_S0_FRAME + i * 2; ++ ctrl = v4l2_ctrl_new_custom(hdl, &ctrl_cfg, ++ NULL); ++ if (!ctrl) ++ dev_err(dev, "Failed to init framerate control %s\n", ++ ctrl_cfg.name); ++ } ++ + sensor->sd.ctrl_handler = hdl; + return 0; + +--- a/drivers/media/i2c/irs1125.h ++++ b/drivers/media/i2c/irs1125.h +@@ -21,18 +21,57 @@ + #define IRS1125_NUM_SEQ_ENTRIES 20 + #define IRS1125_NUM_MOD_PLLS 4 + +-#define IRS1125_CID_CUSTOM_BASE (V4L2_CID_USER_BASE | 0xf000) +-#define IRS1125_CID_SAFE_RECONFIG (IRS1125_CID_CUSTOM_BASE + 0) +-#define IRS1125_CID_CONTINUOUS_TRIG (IRS1125_CID_CUSTOM_BASE + 1) +-#define IRS1125_CID_TRIGGER (IRS1125_CID_CUSTOM_BASE + 2) +-#define IRS1125_CID_RECONFIG (IRS1125_CID_CUSTOM_BASE + 3) +-#define IRS1125_CID_ILLU_ON (IRS1125_CID_CUSTOM_BASE + 4) +-#define IRS1125_CID_NUM_SEQS (IRS1125_CID_CUSTOM_BASE + 5) +-#define IRS1125_CID_MOD_PLL (IRS1125_CID_CUSTOM_BASE + 6) +-#define IRS1125_CID_SEQ_CONFIG (IRS1125_CID_CUSTOM_BASE + 7) +-#define IRS1125_CID_IDENT0 (IRS1125_CID_CUSTOM_BASE + 8) +-#define IRS1125_CID_IDENT1 (IRS1125_CID_CUSTOM_BASE + 9) +-#define IRS1125_CID_IDENT2 (IRS1125_CID_CUSTOM_BASE + 10) ++#define IRS1125_CID_CUSTOM_BASE (V4L2_CID_USER_BASE | 0xf000) ++#define IRS1125_CID_CONTINUOUS_TRIG (IRS1125_CID_CUSTOM_BASE + 1) ++#define IRS1125_CID_TRIGGER (IRS1125_CID_CUSTOM_BASE + 2) ++#define IRS1125_CID_RECONFIG (IRS1125_CID_CUSTOM_BASE + 3) ++#define IRS1125_CID_ILLU_ON (IRS1125_CID_CUSTOM_BASE + 4) ++#define IRS1125_CID_NUM_SEQS (IRS1125_CID_CUSTOM_BASE + 5) ++#define IRS1125_CID_MOD_PLL (IRS1125_CID_CUSTOM_BASE + 6) ++#define IRS1125_CID_SEQ_CONFIG (IRS1125_CID_CUSTOM_BASE + 7) ++#define IRS1125_CID_IDENT0 (IRS1125_CID_CUSTOM_BASE + 8) ++#define IRS1125_CID_IDENT1 (IRS1125_CID_CUSTOM_BASE + 9) ++#define IRS1125_CID_IDENT2 (IRS1125_CID_CUSTOM_BASE + 10) ++#define IRS1125_CID_SAFE_RECONFIG_S0_EXPO (IRS1125_CID_CUSTOM_BASE + 11) ++#define IRS1125_CID_SAFE_RECONFIG_S0_FRAME (IRS1125_CID_CUSTOM_BASE + 12) ++#define IRS1125_CID_SAFE_RECONFIG_S1_EXPO (IRS1125_CID_CUSTOM_BASE + 13) ++#define IRS1125_CID_SAFE_RECONFIG_S1_FRAME (IRS1125_CID_CUSTOM_BASE + 14) ++#define IRS1125_CID_SAFE_RECONFIG_S2_EXPO (IRS1125_CID_CUSTOM_BASE + 15) ++#define IRS1125_CID_SAFE_RECONFIG_S2_FRAME (IRS1125_CID_CUSTOM_BASE + 16) ++#define IRS1125_CID_SAFE_RECONFIG_S3_EXPO (IRS1125_CID_CUSTOM_BASE + 17) ++#define IRS1125_CID_SAFE_RECONFIG_S3_FRAME (IRS1125_CID_CUSTOM_BASE + 18) ++#define IRS1125_CID_SAFE_RECONFIG_S4_EXPO (IRS1125_CID_CUSTOM_BASE + 19) ++#define IRS1125_CID_SAFE_RECONFIG_S4_FRAME (IRS1125_CID_CUSTOM_BASE + 20) ++#define IRS1125_CID_SAFE_RECONFIG_S5_EXPO (IRS1125_CID_CUSTOM_BASE + 21) ++#define IRS1125_CID_SAFE_RECONFIG_S5_FRAME (IRS1125_CID_CUSTOM_BASE + 22) ++#define IRS1125_CID_SAFE_RECONFIG_S6_EXPO (IRS1125_CID_CUSTOM_BASE + 23) ++#define IRS1125_CID_SAFE_RECONFIG_S6_FRAME (IRS1125_CID_CUSTOM_BASE + 24) ++#define IRS1125_CID_SAFE_RECONFIG_S7_EXPO (IRS1125_CID_CUSTOM_BASE + 25) ++#define IRS1125_CID_SAFE_RECONFIG_S7_FRAME (IRS1125_CID_CUSTOM_BASE + 26) ++#define IRS1125_CID_SAFE_RECONFIG_S8_EXPO (IRS1125_CID_CUSTOM_BASE + 27) ++#define IRS1125_CID_SAFE_RECONFIG_S8_FRAME (IRS1125_CID_CUSTOM_BASE + 28) ++#define IRS1125_CID_SAFE_RECONFIG_S9_EXPO (IRS1125_CID_CUSTOM_BASE + 29) ++#define IRS1125_CID_SAFE_RECONFIG_S9_FRAME (IRS1125_CID_CUSTOM_BASE + 30) ++#define IRS1125_CID_SAFE_RECONFIG_S10_EXPO (IRS1125_CID_CUSTOM_BASE + 31) ++#define IRS1125_CID_SAFE_RECONFIG_S10_FRAME (IRS1125_CID_CUSTOM_BASE + 32) ++#define IRS1125_CID_SAFE_RECONFIG_S11_EXPO (IRS1125_CID_CUSTOM_BASE + 33) ++#define IRS1125_CID_SAFE_RECONFIG_S11_FRAME (IRS1125_CID_CUSTOM_BASE + 34) ++#define IRS1125_CID_SAFE_RECONFIG_S12_EXPO (IRS1125_CID_CUSTOM_BASE + 35) ++#define IRS1125_CID_SAFE_RECONFIG_S12_FRAME (IRS1125_CID_CUSTOM_BASE + 36) ++#define IRS1125_CID_SAFE_RECONFIG_S13_EXPO (IRS1125_CID_CUSTOM_BASE + 37) ++#define IRS1125_CID_SAFE_RECONFIG_S13_FRAME (IRS1125_CID_CUSTOM_BASE + 38) ++#define IRS1125_CID_SAFE_RECONFIG_S14_EXPO (IRS1125_CID_CUSTOM_BASE + 39) ++#define IRS1125_CID_SAFE_RECONFIG_S14_FRAME (IRS1125_CID_CUSTOM_BASE + 40) ++#define IRS1125_CID_SAFE_RECONFIG_S15_EXPO (IRS1125_CID_CUSTOM_BASE + 41) ++#define IRS1125_CID_SAFE_RECONFIG_S15_FRAME (IRS1125_CID_CUSTOM_BASE + 42) ++#define IRS1125_CID_SAFE_RECONFIG_S16_EXPO (IRS1125_CID_CUSTOM_BASE + 43) ++#define IRS1125_CID_SAFE_RECONFIG_S16_FRAME (IRS1125_CID_CUSTOM_BASE + 44) ++#define IRS1125_CID_SAFE_RECONFIG_S17_EXPO (IRS1125_CID_CUSTOM_BASE + 45) ++#define IRS1125_CID_SAFE_RECONFIG_S17_FRAME (IRS1125_CID_CUSTOM_BASE + 46) ++#define IRS1125_CID_SAFE_RECONFIG_S18_EXPO (IRS1125_CID_CUSTOM_BASE + 47) ++#define IRS1125_CID_SAFE_RECONFIG_S18_FRAME (IRS1125_CID_CUSTOM_BASE + 48) ++#define IRS1125_CID_SAFE_RECONFIG_S19_EXPO (IRS1125_CID_CUSTOM_BASE + 49) ++#define IRS1125_CID_SAFE_RECONFIG_S19_FRAME (IRS1125_CID_CUSTOM_BASE + 50) + + struct irs1125_seq_cfg { + __u16 exposure; +@@ -41,11 +80,6 @@ struct irs1125_seq_cfg { + __u16 pll; + }; + +-struct irs1125_illu { +- __u16 exposure; +- __u16 framerate; +-}; +- + struct irs1125_mod_pll { + __u16 pllcfg1; + __u16 pllcfg2; diff --git a/target/linux/bcm27xx/patches-5.10/950-0261-media-irs1125-Keep-HW-in-sync-after-imager-reset.patch b/target/linux/bcm27xx/patches-5.10/950-0261-media-irs1125-Keep-HW-in-sync-after-imager-reset.patch new file mode 100644 index 0000000000..1bacd924e2 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0261-media-irs1125-Keep-HW-in-sync-after-imager-reset.patch @@ -0,0 +1,181 @@ +From 60794484c063805631e50b5a4fbc81538d51944e Mon Sep 17 00:00:00 2001 +From: Markus Proeller +Date: Tue, 16 Jun 2020 13:33:56 +0200 +Subject: [PATCH] media: irs1125: Keep HW in sync after imager reset + +When closing the video device, the irs1125 is put in power down state. +To keep V4L2 ctrls and the HW in sync, v4l2_ctrl_handler_setup is +called after power up. + +The compound ctrl IRS1125_CID_MOD_PLL however has a default value +of all zeros, which puts the imager into a non responding state. +Thus, this ctrl is not written by the driver into HW after power up. +The userspace has to take care to write senseful data. + +Signed-off-by: Markus Proeller +--- + drivers/media/i2c/irs1125.c | 121 +++++++++++++++++------------------- + 1 file changed, 58 insertions(+), 63 deletions(-) + +--- a/drivers/media/i2c/irs1125.c ++++ b/drivers/media/i2c/irs1125.c +@@ -82,6 +82,7 @@ struct irs1125 { + struct v4l2_ctrl *ctrl_numseq; + + int power_count; ++ bool mod_pll_init; + }; + + static inline struct irs1125 *to_state(struct v4l2_subdev *sd) +@@ -276,8 +277,7 @@ static struct regval_list irs1125_seq_cf + {0xC039, 0x0000}, + {0xC401, 0x0002}, + +- {0xFFFF, 1}, +- {0xA87C, 0x0001} ++ {0xFFFF, 1} + }; + + static int irs1125_write(struct v4l2_subdev *sd, u16 reg, u16 val) +@@ -471,7 +471,11 @@ static int __sensor_init(struct v4l2_sub + return ret; + } + +- return 0; ++ irs1125->mod_pll_init = true; ++ v4l2_ctrl_handler_setup(&irs1125->ctrl_handler); ++ irs1125->mod_pll_init = false; ++ ++ return irs1125_write(sd, 0xA87C, 0x0001); + } + + static int irs1125_sensor_power(struct v4l2_subdev *sd, int on) +@@ -607,8 +611,6 @@ static int irs1125_s_ctrl(struct v4l2_ct + struct irs1125 *dev = container_of(ctrl->handler, + struct irs1125, ctrl_handler); + struct i2c_client *client = v4l2_get_subdevdata(&dev->sd); +- struct irs1125_mod_pll *mod_cur, *mod_new; +- u16 addr, val; + int err = 0, i; + + switch (ctrl->id) { +@@ -660,68 +662,61 @@ static int irs1125_s_ctrl(struct v4l2_ct + ctrl->val); + break; + } +- case IRS1125_CID_MOD_PLL: ++ case IRS1125_CID_MOD_PLL: { ++ struct irs1125_mod_pll *mod_new; ++ ++ if (dev->mod_pll_init) ++ break; ++ + mod_new = (struct irs1125_mod_pll *)ctrl->p_new.p; +- mod_cur = (struct irs1125_mod_pll *)ctrl->p_cur.p; + for (i = 0; i < IRS1125_NUM_MOD_PLLS; i++) { +- if (mod_cur[i].pllcfg1 != mod_new[i].pllcfg1) { +- addr = 0xC3A0 + i * 3; +- val = mod_new[i].pllcfg1; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } +- if (mod_cur[i].pllcfg2 != mod_new[i].pllcfg2) { +- addr = 0xC3A1 + i * 3; +- val = mod_new[i].pllcfg2; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } +- if (mod_cur[i].pllcfg3 != mod_new[i].pllcfg3) { +- addr = 0xC3A2 + i * 3; +- val = mod_new[i].pllcfg3; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } +- if (mod_cur[i].pllcfg4 != mod_new[i].pllcfg4) { +- addr = 0xC24C + i * 5; +- val = mod_new[i].pllcfg4; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } +- if (mod_cur[i].pllcfg5 != mod_new[i].pllcfg5) { +- addr = 0xC24D + i * 5; +- val = mod_new[i].pllcfg5; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } +- if (mod_cur[i].pllcfg6 != mod_new[i].pllcfg6) { +- addr = 0xC24E + i * 5; +- val = mod_new[i].pllcfg6; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } +- if (mod_cur[i].pllcfg7 != mod_new[i].pllcfg7) { +- addr = 0xC24F + i * 5; +- val = mod_new[i].pllcfg7; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } +- if (mod_cur[i].pllcfg8 != mod_new[i].pllcfg8) { +- addr = 0xC250 + i * 5; +- val = mod_new[i].pllcfg8; +- err = irs1125_write(&dev->sd, addr, val); +- if (err < 0) +- break; +- } ++ unsigned int pll_offset, ssc_offset; ++ ++ pll_offset = i * 3; ++ ssc_offset = i * 5; ++ ++ err = irs1125_write(&dev->sd, 0xC3A0 + pll_offset, ++ mod_new[i].pllcfg1); ++ if (err < 0) ++ break; ++ ++ err = irs1125_write(&dev->sd, 0xC3A1 + pll_offset, ++ mod_new[i].pllcfg2); ++ if (err < 0) ++ break; ++ ++ err = irs1125_write(&dev->sd, 0xC3A2 + pll_offset, ++ mod_new[i].pllcfg3); ++ if (err < 0) ++ break; ++ ++ err = irs1125_write(&dev->sd, 0xC24C + ssc_offset, ++ mod_new[i].pllcfg4); ++ if (err < 0) ++ break; ++ ++ err = irs1125_write(&dev->sd, 0xC24D + ssc_offset, ++ mod_new[i].pllcfg5); ++ if (err < 0) ++ break; ++ ++ err = irs1125_write(&dev->sd, 0xC24E + ssc_offset, ++ mod_new[i].pllcfg6); ++ if (err < 0) ++ break; ++ ++ err = irs1125_write(&dev->sd, 0xC24F + ssc_offset, ++ mod_new[i].pllcfg7); ++ if (err < 0) ++ break; ++ ++ err = irs1125_write(&dev->sd, 0xC250 + ssc_offset, ++ mod_new[i].pllcfg8); ++ if (err < 0) ++ break; + } + break; ++ } + case IRS1125_CID_SEQ_CONFIG: { + struct irs1125_seq_cfg *cfg_new; + diff --git a/target/linux/bcm27xx/patches-5.10/950-0262-staging-bcm2835-audio-Add-missing-MODULE_ALIAS.patch b/target/linux/bcm27xx/patches-5.10/950-0262-staging-bcm2835-audio-Add-missing-MODULE_ALIAS.patch new file mode 100644 index 0000000000..8f3efed07a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0262-staging-bcm2835-audio-Add-missing-MODULE_ALIAS.patch @@ -0,0 +1,30 @@ +From 0465c9ffbf41667c8553d18ace95d2be2f2f4b00 Mon Sep 17 00:00:00 2001 +From: Maxim Mikityanskiy +Date: Sat, 20 Jun 2020 15:40:00 +0300 +Subject: [PATCH] staging: bcm2835-audio: Add missing MODULE_ALIAS + +Commit 8353fe6f1e0f ("Revert "staging: bcm2835-audio: Drop DT +dependency"") reverts the upstream change and makes bcm2835-audio use +device tree again, however, it also removes the MODULE_ALIAS for the +platform device. This MODULE_ALIAS is needed, because VCHIQ registers +bcm2835-audio as a child platform device since commit 25c7597af20d +("staging: vchiq_arm: Register a platform device for audio"), and this +mechanism is adopted also in the downstream kernel. + +This commit puts back that MODULE_ALIAS to make bcm2835-audio +autoprobing work again. The rest of VCHIQ children have their +MODULE_ALIASes in place. + +Fixes: 8353fe6f1e0f ("Revert "staging: bcm2835-audio: Drop DT dependency"") +Signed-off-by: Maxim Mikityanskiy +--- + drivers/staging/vc04_services/bcm2835-audio/bcm2835.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/staging/vc04_services/bcm2835-audio/bcm2835.c ++++ b/drivers/staging/vc04_services/bcm2835-audio/bcm2835.c +@@ -438,3 +438,4 @@ module_platform_driver(bcm2835_alsa_driv + MODULE_AUTHOR("Dom Cobley"); + MODULE_DESCRIPTION("Alsa driver for BCM2835 chip"); + MODULE_LICENSE("GPL"); ++MODULE_ALIAS("platform:bcm2835_audio"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0263-drivers-media-Remove-the-downstream-version-of-bcm28.patch b/target/linux/bcm27xx/patches-5.10/950-0263-drivers-media-Remove-the-downstream-version-of-bcm28.patch new file mode 100644 index 0000000000..381b2a5bd2 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0263-drivers-media-Remove-the-downstream-version-of-bcm28.patch @@ -0,0 +1,3175 @@ +From e1690f8e0f8ac07021dd5e6b53bf6df2c9cf0ae2 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 23 Jun 2020 10:05:57 +0100 +Subject: [PATCH] drivers: media: Remove the downstream version of + bcm2835-unicam + +About to be replaced by the upstream version. + +Signed-off-by: Dave Stevenson +--- + drivers/media/platform/bcm2835/Kconfig | 14 - + drivers/media/platform/bcm2835/Makefile | 3 - + .../media/platform/bcm2835/bcm2835-unicam.c | 2873 ----------------- + .../media/platform/bcm2835/vc4-regs-unicam.h | 253 -- + 4 files changed, 3143 deletions(-) + delete mode 100644 drivers/media/platform/bcm2835/Kconfig + delete mode 100644 drivers/media/platform/bcm2835/Makefile + delete mode 100644 drivers/media/platform/bcm2835/bcm2835-unicam.c + delete mode 100644 drivers/media/platform/bcm2835/vc4-regs-unicam.h + +--- a/drivers/media/platform/bcm2835/Kconfig ++++ /dev/null +@@ -1,14 +0,0 @@ +-# Broadcom VideoCore4 V4L2 camera support +- +-config VIDEO_BCM2835_UNICAM +- tristate "Broadcom BCM2835 Unicam video capture driver" +- depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && MEDIA_CONTROLLER +- depends on ARCH_BCM2835 || COMPILE_TEST +- select VIDEOBUF2_DMA_CONTIG +- select V4L2_FWNODE +- help +- Say Y here to enable V4L2 subdevice for CSI2 receiver. +- This is a V4L2 subdevice that interfaces directly to the VC4 peripheral. +- +- To compile this driver as a module, choose M here. The module +- will be called bcm2835-unicam. +--- a/drivers/media/platform/bcm2835/Makefile ++++ /dev/null +@@ -1,3 +0,0 @@ +-# Makefile for BCM2835 Unicam driver +- +-obj-$(CONFIG_VIDEO_BCM2835_UNICAM) += bcm2835-unicam.o +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ /dev/null +@@ -1,2873 +0,0 @@ +-// SPDX-License-Identifier: GPL-2.0-only +-/* +- * BCM2835 Unicam Capture Driver +- * +- * Copyright (C) 2017-2020 - Raspberry Pi (Trading) Ltd. +- * +- * Dave Stevenson +- * +- * Based on TI am437x driver by +- * Benoit Parrot +- * Lad, Prabhakar +- * +- * and TI CAL camera interface driver by +- * Benoit Parrot +- * +- * +- * There are two camera drivers in the kernel for BCM283x - this one +- * and bcm2835-camera (currently in staging). +- * +- * This driver directly controls the Unicam peripheral - there is no +- * involvement with the VideoCore firmware. Unicam receives CSI-2 or +- * CCP2 data and writes it into SDRAM. +- * The only potential processing options are to repack Bayer data into an +- * alternate format, and applying windowing. +- * The repacking does not shift the data, so can repack V4L2_PIX_FMT_Sxxxx10P +- * to V4L2_PIX_FMT_Sxxxx10, or V4L2_PIX_FMT_Sxxxx12P to V4L2_PIX_FMT_Sxxxx12, +- * but not generically up to V4L2_PIX_FMT_Sxxxx16. The driver will add both +- * formats where the relevant formats are defined, and will automatically +- * configure the repacking as required. +- * Support for windowing may be added later. +- * +- * It should be possible to connect this driver to any sensor with a +- * suitable output interface and V4L2 subdevice driver. +- * +- * bcm2835-camera uses the VideoCore firmware to control the sensor, +- * Unicam, ISP, and all tuner control loops. Fully processed frames are +- * delivered to the driver by the firmware. It only has sensor drivers +- * for Omnivision OV5647, and Sony IMX219 sensors. +- * +- * The two drivers are mutually exclusive for the same Unicam instance. +- * The VideoCore firmware checks the device tree configuration during boot. +- * If it finds device tree nodes called csi0 or csi1 it will block the +- * firmware from accessing the peripheral, and bcm2835-camera will +- * not be able to stream data. +- */ +- +-#include +-#include +-#include +-#include +-#include +-#include +-#include +-#include +-#include +-#include +-#include +-#include +-#include +-#include +-#include +-#include +-#include +- +-#include +-#include +-#include +-#include +-#include +-#include +-#include +-#include +-#include +- +-#include "vc4-regs-unicam.h" +- +-#define UNICAM_MODULE_NAME "unicam" +-#define UNICAM_VERSION "0.1.0" +- +-static int debug; +-module_param(debug, int, 0644); +-MODULE_PARM_DESC(debug, "Debug level 0-3"); +- +-#define unicam_dbg(level, dev, fmt, arg...) \ +- v4l2_dbg(level, debug, &(dev)->v4l2_dev, fmt, ##arg) +-#define unicam_info(dev, fmt, arg...) \ +- v4l2_info(&(dev)->v4l2_dev, fmt, ##arg) +-#define unicam_err(dev, fmt, arg...) \ +- v4l2_err(&(dev)->v4l2_dev, fmt, ##arg) +- +-/* To protect against a dodgy sensor driver never returning an error from +- * enum_mbus_code, set a maximum index value to be used. +- */ +-#define MAX_ENUM_MBUS_CODE 128 +- +-/* +- * Stride is a 16 bit register, but also has to be a multiple of 32. +- */ +-#define BPL_ALIGNMENT 32 +-#define MAX_BYTESPERLINE ((1 << 16) - BPL_ALIGNMENT) +-/* +- * Max width is therefore determined by the max stride divided by +- * the number of bits per pixel. Take 32bpp as a +- * worst case. +- * No imposed limit on the height, so adopt a square image for want +- * of anything better. +- */ +-#define MAX_WIDTH (MAX_BYTESPERLINE / 4) +-#define MAX_HEIGHT MAX_WIDTH +-/* Define a nominal minimum image size */ +-#define MIN_WIDTH 16 +-#define MIN_HEIGHT 16 +-/* Default size of the embedded buffer */ +-#define UNICAM_EMBEDDED_SIZE 8192 +- +-/* +- * Size of the dummy buffer. Can be any size really, but the DMA +- * allocation works in units of page sizes. +- */ +-#define DUMMY_BUF_SIZE (PAGE_SIZE) +- +-enum pad_types { +- IMAGE_PAD, +- METADATA_PAD, +- MAX_NODES +-}; +- +-/* +- * struct unicam_fmt - Unicam media bus format information +- * @pixelformat: V4L2 pixel format FCC identifier. 0 if n/a. +- * @repacked_fourcc: V4L2 pixel format FCC identifier if the data is expanded +- * out to 16bpp. 0 if n/a. +- * @code: V4L2 media bus format code. +- * @depth: Bits per pixel as delivered from the source. +- * @csi_dt: CSI data type. +- * @check_variants: Flag to denote that there are multiple mediabus formats +- * still in the list that could match this V4L2 format. +- */ +-struct unicam_fmt { +- u32 fourcc; +- u32 repacked_fourcc; +- u32 code; +- u8 depth; +- u8 csi_dt; +- u8 check_variants; +-}; +- +-static const struct unicam_fmt formats[] = { +- /* YUV Formats */ +- { +- .fourcc = V4L2_PIX_FMT_YUYV, +- .code = MEDIA_BUS_FMT_YUYV8_2X8, +- .depth = 16, +- .csi_dt = 0x1e, +- .check_variants = 1, +- }, { +- .fourcc = V4L2_PIX_FMT_UYVY, +- .code = MEDIA_BUS_FMT_UYVY8_2X8, +- .depth = 16, +- .csi_dt = 0x1e, +- .check_variants = 1, +- }, { +- .fourcc = V4L2_PIX_FMT_YVYU, +- .code = MEDIA_BUS_FMT_YVYU8_2X8, +- .depth = 16, +- .csi_dt = 0x1e, +- .check_variants = 1, +- }, { +- .fourcc = V4L2_PIX_FMT_VYUY, +- .code = MEDIA_BUS_FMT_VYUY8_2X8, +- .depth = 16, +- .csi_dt = 0x1e, +- .check_variants = 1, +- }, { +- .fourcc = V4L2_PIX_FMT_YUYV, +- .code = MEDIA_BUS_FMT_YUYV8_1X16, +- .depth = 16, +- .csi_dt = 0x1e, +- }, { +- .fourcc = V4L2_PIX_FMT_UYVY, +- .code = MEDIA_BUS_FMT_UYVY8_1X16, +- .depth = 16, +- .csi_dt = 0x1e, +- }, { +- .fourcc = V4L2_PIX_FMT_YVYU, +- .code = MEDIA_BUS_FMT_YVYU8_1X16, +- .depth = 16, +- .csi_dt = 0x1e, +- }, { +- .fourcc = V4L2_PIX_FMT_VYUY, +- .code = MEDIA_BUS_FMT_VYUY8_1X16, +- .depth = 16, +- .csi_dt = 0x1e, +- }, { +- /* RGB Formats */ +- .fourcc = V4L2_PIX_FMT_RGB565, /* gggbbbbb rrrrrggg */ +- .code = MEDIA_BUS_FMT_RGB565_2X8_LE, +- .depth = 16, +- .csi_dt = 0x22, +- }, { +- .fourcc = V4L2_PIX_FMT_RGB565X, /* rrrrrggg gggbbbbb */ +- .code = MEDIA_BUS_FMT_RGB565_2X8_BE, +- .depth = 16, +- .csi_dt = 0x22 +- }, { +- .fourcc = V4L2_PIX_FMT_RGB555, /* gggbbbbb arrrrrgg */ +- .code = MEDIA_BUS_FMT_RGB555_2X8_PADHI_LE, +- .depth = 16, +- .csi_dt = 0x21, +- }, { +- .fourcc = V4L2_PIX_FMT_RGB555X, /* arrrrrgg gggbbbbb */ +- .code = MEDIA_BUS_FMT_RGB555_2X8_PADHI_BE, +- .depth = 16, +- .csi_dt = 0x21, +- }, { +- .fourcc = V4L2_PIX_FMT_RGB24, /* rgb */ +- .code = MEDIA_BUS_FMT_RGB888_1X24, +- .depth = 24, +- .csi_dt = 0x24, +- }, { +- .fourcc = V4L2_PIX_FMT_BGR24, /* bgr */ +- .code = MEDIA_BUS_FMT_BGR888_1X24, +- .depth = 24, +- .csi_dt = 0x24, +- }, { +- .fourcc = V4L2_PIX_FMT_RGB32, /* argb */ +- .code = MEDIA_BUS_FMT_ARGB8888_1X32, +- .depth = 32, +- .csi_dt = 0x0, +- }, { +- /* Bayer Formats */ +- .fourcc = V4L2_PIX_FMT_SBGGR8, +- .code = MEDIA_BUS_FMT_SBGGR8_1X8, +- .depth = 8, +- .csi_dt = 0x2a, +- }, { +- .fourcc = V4L2_PIX_FMT_SGBRG8, +- .code = MEDIA_BUS_FMT_SGBRG8_1X8, +- .depth = 8, +- .csi_dt = 0x2a, +- }, { +- .fourcc = V4L2_PIX_FMT_SGRBG8, +- .code = MEDIA_BUS_FMT_SGRBG8_1X8, +- .depth = 8, +- .csi_dt = 0x2a, +- }, { +- .fourcc = V4L2_PIX_FMT_SRGGB8, +- .code = MEDIA_BUS_FMT_SRGGB8_1X8, +- .depth = 8, +- .csi_dt = 0x2a, +- }, { +- .fourcc = V4L2_PIX_FMT_SBGGR10P, +- .repacked_fourcc = V4L2_PIX_FMT_SBGGR10, +- .code = MEDIA_BUS_FMT_SBGGR10_1X10, +- .depth = 10, +- .csi_dt = 0x2b, +- }, { +- .fourcc = V4L2_PIX_FMT_SGBRG10P, +- .repacked_fourcc = V4L2_PIX_FMT_SGBRG10, +- .code = MEDIA_BUS_FMT_SGBRG10_1X10, +- .depth = 10, +- .csi_dt = 0x2b, +- }, { +- .fourcc = V4L2_PIX_FMT_SGRBG10P, +- .repacked_fourcc = V4L2_PIX_FMT_SGRBG10, +- .code = MEDIA_BUS_FMT_SGRBG10_1X10, +- .depth = 10, +- .csi_dt = 0x2b, +- }, { +- .fourcc = V4L2_PIX_FMT_SRGGB10P, +- .repacked_fourcc = V4L2_PIX_FMT_SRGGB10, +- .code = MEDIA_BUS_FMT_SRGGB10_1X10, +- .depth = 10, +- .csi_dt = 0x2b, +- }, { +- .fourcc = V4L2_PIX_FMT_SBGGR12P, +- .repacked_fourcc = V4L2_PIX_FMT_SBGGR12, +- .code = MEDIA_BUS_FMT_SBGGR12_1X12, +- .depth = 12, +- .csi_dt = 0x2c, +- }, { +- .fourcc = V4L2_PIX_FMT_SGBRG12P, +- .repacked_fourcc = V4L2_PIX_FMT_SGBRG12, +- .code = MEDIA_BUS_FMT_SGBRG12_1X12, +- .depth = 12, +- .csi_dt = 0x2c, +- }, { +- .fourcc = V4L2_PIX_FMT_SGRBG12P, +- .repacked_fourcc = V4L2_PIX_FMT_SGRBG12, +- .code = MEDIA_BUS_FMT_SGRBG12_1X12, +- .depth = 12, +- .csi_dt = 0x2c, +- }, { +- .fourcc = V4L2_PIX_FMT_SRGGB12P, +- .repacked_fourcc = V4L2_PIX_FMT_SRGGB12, +- .code = MEDIA_BUS_FMT_SRGGB12_1X12, +- .depth = 12, +- .csi_dt = 0x2c, +- }, { +- .fourcc = V4L2_PIX_FMT_SBGGR14P, +- .code = MEDIA_BUS_FMT_SBGGR14_1X14, +- .depth = 14, +- .csi_dt = 0x2d, +- }, { +- .fourcc = V4L2_PIX_FMT_SGBRG14P, +- .code = MEDIA_BUS_FMT_SGBRG14_1X14, +- .depth = 14, +- .csi_dt = 0x2d, +- }, { +- .fourcc = V4L2_PIX_FMT_SGRBG14P, +- .code = MEDIA_BUS_FMT_SGRBG14_1X14, +- .depth = 14, +- .csi_dt = 0x2d, +- }, { +- .fourcc = V4L2_PIX_FMT_SRGGB14P, +- .code = MEDIA_BUS_FMT_SRGGB14_1X14, +- .depth = 14, +- .csi_dt = 0x2d, +- }, { +- /* +- * 16 bit Bayer formats could be supported, but there is no CSI2 +- * data_type defined for raw 16, and no sensors that produce it at +- * present. +- */ +- +- /* Greyscale formats */ +- .fourcc = V4L2_PIX_FMT_GREY, +- .code = MEDIA_BUS_FMT_Y8_1X8, +- .depth = 8, +- .csi_dt = 0x2a, +- }, { +- .fourcc = V4L2_PIX_FMT_Y10P, +- .repacked_fourcc = V4L2_PIX_FMT_Y10, +- .code = MEDIA_BUS_FMT_Y10_1X10, +- .depth = 10, +- .csi_dt = 0x2b, +- }, { +- /* NB There is no packed V4L2 fourcc for this format. */ +- .repacked_fourcc = V4L2_PIX_FMT_Y12, +- .code = MEDIA_BUS_FMT_Y12_1X12, +- .depth = 12, +- .csi_dt = 0x2c, +- }, +- /* Embedded data format */ +- { +- .fourcc = V4L2_META_FMT_SENSOR_DATA, +- .code = MEDIA_BUS_FMT_SENSOR_DATA, +- .depth = 8, +- } +-}; +- +-struct unicam_dmaqueue { +- struct list_head active; +-}; +- +-struct unicam_buffer { +- struct vb2_v4l2_buffer vb; +- struct list_head list; +-}; +- +-struct unicam_cfg { +- /* peripheral base address */ +- void __iomem *base; +- /* clock gating base address */ +- void __iomem *clk_gate_base; +-}; +- +-#define MAX_POSSIBLE_PIX_FMTS (ARRAY_SIZE(formats)) +- +-struct unicam_node { +- int registered; +- int open; +- int streaming; +- unsigned int pad_id; +- /* Pointer pointing to current v4l2_buffer */ +- struct unicam_buffer *cur_frm; +- /* Pointer pointing to next v4l2_buffer */ +- struct unicam_buffer *next_frm; +- /* video capture */ +- const struct unicam_fmt *fmt; +- /* Used to store current pixel format */ +- struct v4l2_format v_fmt; +- /* Used to store current mbus frame format */ +- struct v4l2_mbus_framefmt m_fmt; +- /* Buffer queue used in video-buf */ +- struct vb2_queue buffer_queue; +- /* Queue of filled frames */ +- struct unicam_dmaqueue dma_queue; +- /* IRQ lock for DMA queue */ +- spinlock_t dma_queue_lock; +- /* lock used to access this structure */ +- struct mutex lock; +- /* Identifies video device for this channel */ +- struct video_device video_dev; +- /* Pointer to the parent handle */ +- struct unicam_device *dev; +- struct media_pad pad; +- struct v4l2_ctrl_handler ctrl_handler; +- unsigned int embedded_lines; +- /* +- * Dummy buffer intended to be used by unicam +- * if we have no other queued buffers to swap to. +- */ +- void *dummy_buf_cpu_addr; +- dma_addr_t dummy_buf_dma_addr; +-}; +- +-struct unicam_device { +- /* V4l2 specific parameters */ +- +- struct v4l2_fwnode_endpoint endpoint; +- +- struct v4l2_async_subdev asd; +- +- /* unicam cfg */ +- struct unicam_cfg cfg; +- /* clock handle */ +- struct clk *clock; +- /* V4l2 device */ +- struct v4l2_device v4l2_dev; +- struct media_device mdev; +- +- /* parent device */ +- struct platform_device *pdev; +- /* subdevice async Notifier */ +- struct v4l2_async_notifier notifier; +- unsigned int sequence; +- +- /* ptr to sub device */ +- struct v4l2_subdev *sensor; +- /* Pad config for the sensor */ +- struct v4l2_subdev_pad_config *sensor_config; +- +- unsigned int virtual_channel; +- enum v4l2_mbus_type bus_type; +- /* +- * Stores bus.mipi_csi2.flags for CSI2 sensors, or +- * bus.mipi_csi1.strobe for CCP2. +- */ +- unsigned int bus_flags; +- unsigned int max_data_lanes; +- unsigned int active_data_lanes; +- bool sensor_embedded_data; +- +- struct unicam_node node[MAX_NODES]; +-}; +- +-/* Hardware access */ +-#define clk_write(dev, val) writel((val) | 0x5a000000, (dev)->clk_gate_base) +-#define clk_read(dev) readl((dev)->clk_gate_base) +- +-#define reg_read(dev, offset) readl((dev)->base + (offset)) +-#define reg_write(dev, offset, val) writel(val, (dev)->base + (offset)) +- +-#define reg_read_field(dev, offset, mask) get_field(reg_read((dev), (offset), \ +- mask)) +- +-static inline int get_field(u32 value, u32 mask) +-{ +- return (value & mask) >> __ffs(mask); +-} +- +-static inline void set_field(u32 *valp, u32 field, u32 mask) +-{ +- u32 val = *valp; +- +- val &= ~mask; +- val |= (field << __ffs(mask)) & mask; +- *valp = val; +-} +- +-static inline void reg_write_field(struct unicam_cfg *dev, u32 offset, +- u32 field, u32 mask) +-{ +- u32 val = reg_read((dev), (offset)); +- +- set_field(&val, field, mask); +- reg_write((dev), (offset), val); +-} +- +-/* Power management functions */ +-static inline int unicam_runtime_get(struct unicam_device *dev) +-{ +- return pm_runtime_get_sync(&dev->pdev->dev); +-} +- +-static inline void unicam_runtime_put(struct unicam_device *dev) +-{ +- pm_runtime_put_sync(&dev->pdev->dev); +-} +- +-/* Format setup functions */ +-static const struct unicam_fmt *find_format_by_code(u32 code) +-{ +- unsigned int i; +- +- for (i = 0; i < ARRAY_SIZE(formats); i++) { +- if (formats[i].code == code) +- return &formats[i]; +- } +- +- return NULL; +-} +- +-static int check_mbus_format(struct unicam_device *dev, +- const struct unicam_fmt *format) +-{ +- struct v4l2_subdev_mbus_code_enum mbus_code; +- int ret = 0; +- int i; +- +- for (i = 0; !ret && i < MAX_ENUM_MBUS_CODE; i++) { +- memset(&mbus_code, 0, sizeof(mbus_code)); +- mbus_code.index = i; +- mbus_code.pad = IMAGE_PAD; +- mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE; +- +- ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, +- NULL, &mbus_code); +- +- if (!ret && mbus_code.code == format->code) +- return 1; +- } +- +- return 0; +-} +- +-static const struct unicam_fmt *find_format_by_pix(struct unicam_device *dev, +- u32 pixelformat) +-{ +- unsigned int i; +- +- for (i = 0; i < ARRAY_SIZE(formats); i++) { +- if (formats[i].fourcc == pixelformat || +- formats[i].repacked_fourcc == pixelformat) { +- if (formats[i].check_variants && +- !check_mbus_format(dev, &formats[i])) +- continue; +- return &formats[i]; +- } +- } +- +- return NULL; +-} +- +-static inline unsigned int bytes_per_line(u32 width, +- const struct unicam_fmt *fmt, +- u32 v4l2_fourcc) +-{ +- if (v4l2_fourcc == fmt->repacked_fourcc) +- /* Repacking always goes to 16bpp */ +- return ALIGN(width << 1, BPL_ALIGNMENT); +- else +- return ALIGN((width * fmt->depth) >> 3, BPL_ALIGNMENT); +-} +- +-static int __subdev_get_format(struct unicam_device *dev, +- struct v4l2_mbus_framefmt *fmt, int pad_id) +-{ +- struct v4l2_subdev_format sd_fmt = { +- .which = V4L2_SUBDEV_FORMAT_ACTIVE, +- .pad = pad_id +- }; +- int ret; +- +- ret = v4l2_subdev_call(dev->sensor, pad, get_fmt, dev->sensor_config, +- &sd_fmt); +- if (ret < 0) +- return ret; +- +- *fmt = sd_fmt.format; +- +- unicam_dbg(1, dev, "%s %dx%d code:%04x\n", __func__, +- fmt->width, fmt->height, fmt->code); +- +- return 0; +-} +- +-static int __subdev_set_format(struct unicam_device *dev, +- struct v4l2_mbus_framefmt *fmt, int pad_id) +-{ +- struct v4l2_subdev_format sd_fmt = { +- .which = V4L2_SUBDEV_FORMAT_ACTIVE, +- .pad = pad_id +- }; +- int ret; +- +- sd_fmt.format = *fmt; +- +- ret = v4l2_subdev_call(dev->sensor, pad, set_fmt, dev->sensor_config, +- &sd_fmt); +- if (ret < 0) +- return ret; +- +- if (pad_id == IMAGE_PAD) +- unicam_dbg(1, dev, "%s %dx%d code:%04x\n", __func__, fmt->width, +- fmt->height, fmt->code); +- else +- unicam_dbg(1, dev, "%s Embedded data code:%04x\n", __func__, +- sd_fmt.format.code); +- +- return 0; +-} +- +-static int unicam_calc_format_size_bpl(struct unicam_device *dev, +- const struct unicam_fmt *fmt, +- struct v4l2_format *f) +-{ +- unsigned int min_bytesperline; +- +- v4l_bound_align_image(&f->fmt.pix.width, MIN_WIDTH, MAX_WIDTH, 2, +- &f->fmt.pix.height, MIN_HEIGHT, MAX_HEIGHT, 0, +- 0); +- +- min_bytesperline = bytes_per_line(f->fmt.pix.width, fmt, +- f->fmt.pix.pixelformat); +- +- if (f->fmt.pix.bytesperline > min_bytesperline && +- f->fmt.pix.bytesperline <= MAX_BYTESPERLINE) +- f->fmt.pix.bytesperline = ALIGN(f->fmt.pix.bytesperline, +- BPL_ALIGNMENT); +- else +- f->fmt.pix.bytesperline = min_bytesperline; +- +- f->fmt.pix.sizeimage = f->fmt.pix.height * f->fmt.pix.bytesperline; +- +- unicam_dbg(3, dev, "%s: fourcc: %08X size: %dx%d bpl:%d img_size:%d\n", +- __func__, +- f->fmt.pix.pixelformat, +- f->fmt.pix.width, f->fmt.pix.height, +- f->fmt.pix.bytesperline, f->fmt.pix.sizeimage); +- +- return 0; +-} +- +-static int unicam_reset_format(struct unicam_node *node) +-{ +- struct unicam_device *dev = node->dev; +- struct v4l2_mbus_framefmt mbus_fmt; +- int ret; +- +- if (dev->sensor_embedded_data || node->pad_id != METADATA_PAD) { +- ret = __subdev_get_format(dev, &mbus_fmt, node->pad_id); +- if (ret) { +- unicam_err(dev, "Failed to get_format - ret %d\n", ret); +- return ret; +- } +- +- if (mbus_fmt.code != node->fmt->code) { +- unicam_err(dev, "code mismatch - fmt->code %08x, mbus_fmt.code %08x\n", +- node->fmt->code, mbus_fmt.code); +- return ret; +- } +- } +- +- if (node->pad_id == IMAGE_PAD) { +- v4l2_fill_pix_format(&node->v_fmt.fmt.pix, &mbus_fmt); +- node->v_fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE; +- unicam_calc_format_size_bpl(dev, node->fmt, &node->v_fmt); +- } else { +- node->v_fmt.type = V4L2_BUF_TYPE_META_CAPTURE; +- node->v_fmt.fmt.meta.dataformat = V4L2_META_FMT_SENSOR_DATA; +- if (dev->sensor_embedded_data) { +- node->v_fmt.fmt.meta.buffersize = +- mbus_fmt.width * mbus_fmt.height; +- node->embedded_lines = mbus_fmt.height; +- } else { +- node->v_fmt.fmt.meta.buffersize = UNICAM_EMBEDDED_SIZE; +- node->embedded_lines = 1; +- } +- } +- +- node->m_fmt = mbus_fmt; +- return 0; +-} +- +-static void unicam_wr_dma_addr(struct unicam_cfg *cfg, dma_addr_t dmaaddr, +- unsigned int buffer_size, int pad_id) +-{ +- dma_addr_t endaddr = dmaaddr + buffer_size; +- +- /* +- * dmaaddr and endaddr should be a 32-bit address with the top two bits +- * set to 0x3 to signify uncached access through the Videocore memory +- * controller. +- */ +- BUG_ON((dmaaddr >> 30) != 0x3 && (endaddr >> 30) != 0x3); +- +- if (pad_id == IMAGE_PAD) { +- reg_write(cfg, UNICAM_IBSA0, dmaaddr); +- reg_write(cfg, UNICAM_IBEA0, endaddr); +- } else { +- reg_write(cfg, UNICAM_DBSA0, dmaaddr); +- reg_write(cfg, UNICAM_DBEA0, endaddr); +- } +-} +- +-static inline unsigned int unicam_get_lines_done(struct unicam_device *dev) +-{ +- dma_addr_t start_addr, cur_addr; +- unsigned int stride = dev->node[IMAGE_PAD].v_fmt.fmt.pix.bytesperline; +- struct unicam_buffer *frm = dev->node[IMAGE_PAD].cur_frm; +- +- if (!frm) +- return 0; +- +- start_addr = vb2_dma_contig_plane_dma_addr(&frm->vb.vb2_buf, 0); +- cur_addr = reg_read(&dev->cfg, UNICAM_IBWP); +- return (unsigned int)(cur_addr - start_addr) / stride; +-} +- +-static inline void unicam_schedule_next_buffer(struct unicam_node *node) +-{ +- struct unicam_device *dev = node->dev; +- struct unicam_dmaqueue *dma_q = &node->dma_queue; +- struct unicam_buffer *buf; +- unsigned int size; +- dma_addr_t addr; +- +- buf = list_entry(dma_q->active.next, struct unicam_buffer, list); +- node->next_frm = buf; +- list_del(&buf->list); +- +- addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0); +- size = (node->pad_id == IMAGE_PAD) ? +- dev->node[IMAGE_PAD].v_fmt.fmt.pix.sizeimage : +- dev->node[METADATA_PAD].v_fmt.fmt.meta.buffersize; +- +- unicam_wr_dma_addr(&dev->cfg, addr, size, node->pad_id); +-} +- +-static inline void unicam_schedule_dummy_buffer(struct unicam_node *node) +-{ +- struct unicam_device *dev = node->dev; +- dma_addr_t addr = node->dummy_buf_dma_addr; +- +- unicam_dbg(3, dev, "Scheduling dummy buffer for node %d\n", +- node->pad_id); +- +- unicam_wr_dma_addr(&dev->cfg, addr, DUMMY_BUF_SIZE, node->pad_id); +- node->next_frm = NULL; +-} +- +-static inline void unicam_process_buffer_complete(struct unicam_node *node, +- unsigned int sequence) +-{ +- node->cur_frm->vb.field = node->m_fmt.field; +- node->cur_frm->vb.sequence = sequence; +- +- vb2_buffer_done(&node->cur_frm->vb.vb2_buf, VB2_BUF_STATE_DONE); +-} +- +-static int unicam_num_nodes_streaming(struct unicam_device *dev) +-{ +- return dev->node[IMAGE_PAD].streaming + +- dev->node[METADATA_PAD].streaming; +-} +- +-static int unicam_all_nodes_streaming(struct unicam_device *dev) +-{ +- int ret; +- +- ret = dev->node[IMAGE_PAD].open && dev->node[IMAGE_PAD].streaming; +- ret &= !dev->node[METADATA_PAD].open || +- dev->node[METADATA_PAD].streaming; +- return ret; +-} +- +-static void unicam_queue_event_sof(struct unicam_device *unicam) +-{ +- struct v4l2_event event = { +- .type = V4L2_EVENT_FRAME_SYNC, +- .u.frame_sync.frame_sequence = unicam->sequence, +- }; +- +- v4l2_event_queue(&unicam->node[IMAGE_PAD].video_dev, &event); +-} +- +-/* +- * unicam_isr : ISR handler for unicam capture +- * @irq: irq number +- * @dev_id: dev_id ptr +- * +- * It changes status of the captured buffer, takes next buffer from the queue +- * and sets its address in unicam registers +- */ +-static irqreturn_t unicam_isr(int irq, void *dev) +-{ +- struct unicam_device *unicam = (struct unicam_device *)dev; +- struct unicam_cfg *cfg = &unicam->cfg; +- unsigned int lines_done = unicam_get_lines_done(dev); +- unsigned int sequence = unicam->sequence; +- int num_nodes_streaming = unicam_num_nodes_streaming(dev); +- int ista, sta; +- u64 ts; +- int i; +- +- sta = reg_read(cfg, UNICAM_STA); +- /* Write value back to clear the interrupts */ +- reg_write(cfg, UNICAM_STA, sta); +- +- ista = reg_read(cfg, UNICAM_ISTA); +- /* Write value back to clear the interrupts */ +- reg_write(cfg, UNICAM_ISTA, ista); +- +- unicam_dbg(3, unicam, "ISR: ISTA: 0x%X, STA: 0x%X, sequence %d, lines done %d", +- ista, sta, sequence, lines_done); +- +- if (!(sta && (UNICAM_IS | UNICAM_PI0))) +- return IRQ_HANDLED; +- +- /* +- * We must run the frame end handler first. If we have a valid next_frm +- * and we get a simultaneout FE + FS interrupt, running the FS handler +- * first would null out the next_frm ptr and we would have lost the +- * buffer forever. +- */ +- if (ista & UNICAM_FEI || sta & UNICAM_PI0) { +- /* +- * Ensure we have swapped buffers already as we can't +- * stop the peripheral. If no buffer is available, use a +- * dummy buffer to dump out frames until we get a new buffer +- * to use. +- */ +- for (i = 0; i < num_nodes_streaming; i++) { +- if (unicam->node[i].cur_frm) +- unicam_process_buffer_complete(&unicam->node[i], +- sequence); +- unicam->node[i].cur_frm = unicam->node[i].next_frm; +- } +- unicam->sequence++; +- } +- +- if (ista & UNICAM_FSI) { +- /* +- * Timestamp is to be when the first data byte was captured, +- * aka frame start. +- */ +- ts = ktime_get_ns(); +- for (i = 0; i < num_nodes_streaming; i++) { +- if (unicam->node[i].cur_frm) +- unicam->node[i].cur_frm->vb.vb2_buf.timestamp = +- ts; +- /* +- * Set the next frame output to go to a dummy frame +- * if we have not managed to obtain another frame +- * from the queue. +- */ +- unicam_schedule_dummy_buffer(&unicam->node[i]); +- } +- +- unicam_queue_event_sof(unicam); +- } +- /* +- * Cannot swap buffer at frame end, there may be a race condition +- * where the HW does not actually swap it if the new frame has +- * already started. +- */ +- if (ista & (UNICAM_FSI | UNICAM_LCI) && !(ista & UNICAM_FEI)) { +- for (i = 0; i < num_nodes_streaming; i++) { +- spin_lock(&unicam->node[i].dma_queue_lock); +- if (!list_empty(&unicam->node[i].dma_queue.active) && +- !unicam->node[i].next_frm) +- unicam_schedule_next_buffer(&unicam->node[i]); +- spin_unlock(&unicam->node[i].dma_queue_lock); +- } +- } +- +- if (reg_read(&unicam->cfg, UNICAM_ICTL) & UNICAM_FCM) { +- /* Switch out of trigger mode if selected */ +- reg_write_field(&unicam->cfg, UNICAM_ICTL, 1, UNICAM_TFC); +- reg_write_field(&unicam->cfg, UNICAM_ICTL, 0, UNICAM_FCM); +- } +- return IRQ_HANDLED; +-} +- +-static int unicam_querycap(struct file *file, void *priv, +- struct v4l2_capability *cap) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- +- strlcpy(cap->driver, UNICAM_MODULE_NAME, sizeof(cap->driver)); +- strlcpy(cap->card, UNICAM_MODULE_NAME, sizeof(cap->card)); +- +- snprintf(cap->bus_info, sizeof(cap->bus_info), +- "platform:%s", dev->v4l2_dev.name); +- +- cap->capabilities = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING | +- V4L2_CAP_READWRITE | V4L2_CAP_DEVICE_CAPS | +- V4L2_CAP_META_CAPTURE; +- +- if (node->pad_id == IMAGE_PAD) +- cap->device_caps = V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING; +- else +- cap->device_caps = V4L2_CAP_META_CAPTURE | V4L2_CAP_STREAMING; +- +- return 0; +-} +- +-static int unicam_enum_fmt_vid_cap(struct file *file, void *priv, +- struct v4l2_fmtdesc *f) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- struct v4l2_subdev_mbus_code_enum mbus_code; +- const struct unicam_fmt *fmt = NULL; +- int index = 0; +- int ret = 0; +- int i; +- +- if (node->pad_id == METADATA_PAD) +- return -EINVAL; +- +- for (i = 0; !ret && i < MAX_ENUM_MBUS_CODE; i++) { +- memset(&mbus_code, 0, sizeof(mbus_code)); +- mbus_code.index = i; +- mbus_code.pad = IMAGE_PAD; +- mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE; +- +- ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, +- NULL, &mbus_code); +- if (ret < 0) { +- unicam_dbg(2, dev, +- "subdev->enum_mbus_code idx %d returned %d - index invalid\n", +- i, ret); +- return -EINVAL; +- } +- +- fmt = find_format_by_code(mbus_code.code); +- if (fmt) { +- if (fmt->fourcc) { +- if (index == f->index) { +- f->pixelformat = fmt->fourcc; +- break; +- } +- index++; +- } +- if (fmt->repacked_fourcc) { +- if (index == f->index) { +- f->pixelformat = fmt->repacked_fourcc; +- break; +- } +- index++; +- } +- } +- } +- +- return 0; +-} +- +-static int unicam_g_fmt_vid_cap(struct file *file, void *priv, +- struct v4l2_format *f) +-{ +- struct v4l2_mbus_framefmt mbus_fmt = {0}; +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- const struct unicam_fmt *fmt = NULL; +- int ret; +- +- if (node->pad_id != IMAGE_PAD) +- return -EINVAL; +- +- /* +- * If a flip has occurred in the sensor, the fmt code might have +- * changed. So we will need to re-fetch the format from the subdevice. +- */ +- ret = __subdev_get_format(dev, &mbus_fmt, node->pad_id); +- if (ret) +- return -EINVAL; +- +- /* Find the V4L2 format from mbus code. We must match a known format. */ +- fmt = find_format_by_code(mbus_fmt.code); +- if (!fmt) +- return -EINVAL; +- +- if (node->fmt != fmt) { +- /* +- * The sensor format has changed so the pixelformat needs to +- * be updated. Try and retain the packed/unpacked choice if +- * at all possible. +- */ +- if (node->fmt->repacked_fourcc == +- node->v_fmt.fmt.pix.pixelformat) +- /* Using the repacked format */ +- node->v_fmt.fmt.pix.pixelformat = fmt->repacked_fourcc; +- else +- /* Using the native format */ +- node->v_fmt.fmt.pix.pixelformat = fmt->fourcc; +- +- node->fmt = fmt; +- } +- +- *f = node->v_fmt; +- +- return 0; +-} +- +-static +-const struct unicam_fmt *get_first_supported_format(struct unicam_device *dev) +-{ +- struct v4l2_subdev_mbus_code_enum mbus_code; +- const struct unicam_fmt *fmt = NULL; +- int ret = 0; +- int j; +- +- for (j = 0; ret != -EINVAL && ret != -ENOIOCTLCMD; ++j) { +- memset(&mbus_code, 0, sizeof(mbus_code)); +- mbus_code.index = j; +- mbus_code.pad = IMAGE_PAD; +- mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE; +- +- ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, NULL, +- &mbus_code); +- if (ret < 0) { +- unicam_dbg(2, dev, +- "subdev->enum_mbus_code idx %d returned %d - continue\n", +- j, ret); +- continue; +- } +- +- unicam_dbg(2, dev, "subdev %s: code: 0x%08x idx: %d\n", +- dev->sensor->name, mbus_code.code, j); +- +- fmt = find_format_by_code(mbus_code.code); +- unicam_dbg(2, dev, "fmt 0x%08x returned as %p, V4L2 FOURCC 0x%08x, csi_dt 0x%02x\n", +- mbus_code.code, fmt, fmt ? fmt->fourcc : 0, +- fmt ? fmt->csi_dt : 0); +- if (fmt) +- return fmt; +- } +- +- return NULL; +-} +- +-static int unicam_try_fmt_vid_cap(struct file *file, void *priv, +- struct v4l2_format *f) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- struct v4l2_subdev_format sd_fmt = { +- .which = V4L2_SUBDEV_FORMAT_TRY, +- .pad = IMAGE_PAD +- }; +- struct v4l2_mbus_framefmt *mbus_fmt = &sd_fmt.format; +- const struct unicam_fmt *fmt; +- int ret; +- +- if (node->pad_id == METADATA_PAD) +- return -EINVAL; +- +- fmt = find_format_by_pix(dev, f->fmt.pix.pixelformat); +- if (!fmt) { +- /* Pixel format not supported by unicam. Choose the first +- * supported format, and let the sensor choose something else. +- */ +- unicam_dbg(3, dev, "Fourcc format (0x%08x) not found. Use first format.\n", +- f->fmt.pix.pixelformat); +- +- fmt = &formats[0]; +- f->fmt.pix.pixelformat = fmt->fourcc; +- } +- +- v4l2_fill_mbus_format(mbus_fmt, &f->fmt.pix, fmt->code); +- /* +- * No support for receiving interlaced video, so never +- * request it from the sensor subdev. +- */ +- mbus_fmt->field = V4L2_FIELD_NONE; +- +- ret = v4l2_subdev_call(dev->sensor, pad, set_fmt, dev->sensor_config, +- &sd_fmt); +- if (ret && ret != -ENOIOCTLCMD && ret != -ENODEV) +- return ret; +- +- if (mbus_fmt->field != V4L2_FIELD_NONE) +- unicam_info(dev, "Sensor trying to send interlaced video - results may be unpredictable\n"); +- +- v4l2_fill_pix_format(&f->fmt.pix, &sd_fmt.format); +- if (mbus_fmt->code != fmt->code) { +- /* Sensor has returned an alternate format */ +- fmt = find_format_by_code(mbus_fmt->code); +- if (!fmt) { +- /* The alternate format is one unicam can't support. +- * Find the first format that is supported by both, and +- * then set that. +- */ +- fmt = get_first_supported_format(dev); +- mbus_fmt->code = fmt->code; +- +- ret = v4l2_subdev_call(dev->sensor, pad, set_fmt, +- dev->sensor_config, &sd_fmt); +- if (ret && ret != -ENOIOCTLCMD && ret != -ENODEV) +- return ret; +- +- if (mbus_fmt->field != V4L2_FIELD_NONE) +- unicam_info(dev, "Sensor trying to send interlaced video - results may be unpredictable\n"); +- +- v4l2_fill_pix_format(&f->fmt.pix, &sd_fmt.format); +- +- if (mbus_fmt->code != fmt->code) { +- /* We've set a format that the sensor reports +- * as being supported, but it refuses to set it. +- * Not much else we can do. +- * Assume that the sensor driver may accept the +- * format when it is set (rather than tried). +- */ +- unicam_err(dev, "Sensor won't accept default format, and Unicam can't support sensor default\n"); +- } +- } +- +- if (fmt->fourcc) +- f->fmt.pix.pixelformat = fmt->fourcc; +- else +- f->fmt.pix.pixelformat = fmt->repacked_fourcc; +- } +- +- return unicam_calc_format_size_bpl(dev, fmt, f); +-} +- +-static int unicam_s_fmt_vid_cap(struct file *file, void *priv, +- struct v4l2_format *f) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- struct vb2_queue *q = &node->buffer_queue; +- struct v4l2_mbus_framefmt mbus_fmt = {0}; +- const struct unicam_fmt *fmt; +- int ret; +- +- if (vb2_is_busy(q)) +- return -EBUSY; +- +- ret = unicam_try_fmt_vid_cap(file, priv, f); +- if (ret < 0) +- return ret; +- +- fmt = find_format_by_pix(dev, f->fmt.pix.pixelformat); +- if (!fmt) { +- /* Unknown pixel format - adopt a default. +- * This shouldn't happen as try_fmt should have resolved any +- * issues first. +- */ +- fmt = get_first_supported_format(dev); +- if (!fmt) +- /* It shouldn't be possible to get here with no +- * supported formats +- */ +- return -EINVAL; +- f->fmt.pix.pixelformat = fmt->fourcc; +- return -EINVAL; +- } +- +- v4l2_fill_mbus_format(&mbus_fmt, &f->fmt.pix, fmt->code); +- +- ret = __subdev_set_format(dev, &mbus_fmt, node->pad_id); +- if (ret) { +- unicam_dbg(3, dev, "%s __subdev_set_format failed %d\n", +- __func__, ret); +- return ret; +- } +- +- /* Just double check nothing has gone wrong */ +- if (mbus_fmt.code != fmt->code) { +- unicam_dbg(3, dev, +- "%s subdev changed format on us, this should not happen\n", +- __func__); +- return -EINVAL; +- } +- +- node->fmt = fmt; +- node->v_fmt.fmt.pix.pixelformat = f->fmt.pix.pixelformat; +- node->v_fmt.fmt.pix.bytesperline = f->fmt.pix.bytesperline; +- unicam_reset_format(node); +- +- unicam_dbg(3, dev, +- "%s %dx%d, mbus_fmt 0x%08X, V4L2 pix 0x%08X.\n", +- __func__, node->v_fmt.fmt.pix.width, +- node->v_fmt.fmt.pix.height, mbus_fmt.code, +- node->v_fmt.fmt.pix.pixelformat); +- +- *f = node->v_fmt; +- +- return 0; +-} +- +-static int unicam_enum_fmt_meta_cap(struct file *file, void *priv, +- struct v4l2_fmtdesc *f) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- struct v4l2_subdev_mbus_code_enum mbus_code; +- const struct unicam_fmt *fmt = NULL; +- int ret = 0; +- +- if (node->pad_id != METADATA_PAD || f->index != 0) +- return -EINVAL; +- +- if (dev->sensor_embedded_data) { +- memset(&mbus_code, 0, sizeof(mbus_code)); +- mbus_code.index = f->index; +- mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE; +- mbus_code.pad = METADATA_PAD; +- +- ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, NULL, +- &mbus_code); +- if (ret < 0) { +- unicam_dbg(2, dev, +- "subdev->enum_mbus_code idx 0 returned %d - index invalid\n", +- ret); +- return -EINVAL; +- } +- } else { +- mbus_code.code = MEDIA_BUS_FMT_SENSOR_DATA; +- } +- +- fmt = find_format_by_code(mbus_code.code); +- if (fmt) +- f->pixelformat = fmt->fourcc; +- +- return 0; +-} +- +-static int unicam_g_fmt_meta_cap(struct file *file, void *priv, +- struct v4l2_format *f) +-{ +- struct unicam_node *node = video_drvdata(file); +- +- if (node->pad_id != METADATA_PAD) +- return -EINVAL; +- +- *f = node->v_fmt; +- +- return 0; +-} +- +-static int unicam_try_fmt_meta_cap(struct file *file, void *priv, +- struct v4l2_format *f) +-{ +- struct unicam_node *node = video_drvdata(file); +- +- if (node->pad_id != METADATA_PAD) +- return -EINVAL; +- +- *f = node->v_fmt; +- +- return 0; +-} +- +-static int unicam_s_fmt_meta_cap(struct file *file, void *priv, +- struct v4l2_format *f) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- struct v4l2_mbus_framefmt mbus_fmt = { 0 }; +- const struct unicam_fmt *fmt; +- int ret; +- +- if (node->pad_id == IMAGE_PAD) +- return -EINVAL; +- +- if (dev->sensor_embedded_data) { +- fmt = find_format_by_pix(dev, f->fmt.meta.dataformat); +- if (!fmt) { +- unicam_err(dev, "unknown format: V4L2 pix 0x%08x\n", +- f->fmt.meta.dataformat); +- return -EINVAL; +- } +- mbus_fmt.code = fmt->code; +- ret = __subdev_set_format(dev, &mbus_fmt, node->pad_id); +- if (ret) { +- unicam_dbg(3, dev, "%s __subdev_set_format failed %d\n", +- __func__, ret); +- return ret; +- } +- } +- +- *f = node->v_fmt; +- +- unicam_dbg(3, dev, "%s size %d, V4L2 pix 0x%08x\n", +- __func__, node->v_fmt.fmt.meta.buffersize, +- node->v_fmt.fmt.meta.dataformat); +- +- return 0; +-} +- +-static int unicam_queue_setup(struct vb2_queue *vq, +- unsigned int *nbuffers, +- unsigned int *nplanes, +- unsigned int sizes[], +- struct device *alloc_devs[]) +-{ +- struct unicam_node *node = vb2_get_drv_priv(vq); +- struct unicam_device *dev = node->dev; +- unsigned int size = node->pad_id == IMAGE_PAD ? +- node->v_fmt.fmt.pix.sizeimage : +- node->v_fmt.fmt.meta.buffersize; +- +- if (vq->num_buffers + *nbuffers < 3) +- *nbuffers = 3 - vq->num_buffers; +- +- if (*nplanes) { +- if (sizes[0] < size) { +- unicam_err(dev, "sizes[0] %i < size %u\n", sizes[0], +- size); +- return -EINVAL; +- } +- size = sizes[0]; +- } +- +- *nplanes = 1; +- sizes[0] = size; +- +- return 0; +-} +- +-static int unicam_buffer_prepare(struct vb2_buffer *vb) +-{ +- struct unicam_node *node = vb2_get_drv_priv(vb->vb2_queue); +- struct unicam_device *dev = node->dev; +- struct unicam_buffer *buf = container_of(vb, struct unicam_buffer, +- vb.vb2_buf); +- unsigned long size; +- +- if (WARN_ON(!node->fmt)) +- return -EINVAL; +- +- size = node->pad_id == IMAGE_PAD ? node->v_fmt.fmt.pix.sizeimage : +- node->v_fmt.fmt.meta.buffersize; +- if (vb2_plane_size(vb, 0) < size) { +- unicam_err(dev, "data will not fit into plane (%lu < %lu)\n", +- vb2_plane_size(vb, 0), size); +- return -EINVAL; +- } +- +- vb2_set_plane_payload(&buf->vb.vb2_buf, 0, size); +- return 0; +-} +- +-static void unicam_buffer_queue(struct vb2_buffer *vb) +-{ +- struct unicam_node *node = vb2_get_drv_priv(vb->vb2_queue); +- struct unicam_buffer *buf = container_of(vb, struct unicam_buffer, +- vb.vb2_buf); +- struct unicam_dmaqueue *dma_queue = &node->dma_queue; +- unsigned long flags = 0; +- +- spin_lock_irqsave(&node->dma_queue_lock, flags); +- list_add_tail(&buf->list, &dma_queue->active); +- spin_unlock_irqrestore(&node->dma_queue_lock, flags); +-} +- +-static void unicam_set_packing_config(struct unicam_device *dev) +-{ +- int pack, unpack; +- u32 val; +- +- if (dev->node[IMAGE_PAD].v_fmt.fmt.pix.pixelformat == +- dev->node[IMAGE_PAD].fmt->fourcc) { +- unpack = UNICAM_PUM_NONE; +- pack = UNICAM_PPM_NONE; +- } else { +- switch (dev->node[IMAGE_PAD].fmt->depth) { +- case 8: +- unpack = UNICAM_PUM_UNPACK8; +- break; +- case 10: +- unpack = UNICAM_PUM_UNPACK10; +- break; +- case 12: +- unpack = UNICAM_PUM_UNPACK12; +- break; +- case 14: +- unpack = UNICAM_PUM_UNPACK14; +- break; +- case 16: +- unpack = UNICAM_PUM_UNPACK16; +- break; +- default: +- unpack = UNICAM_PUM_NONE; +- break; +- } +- +- /* Repacking is always to 16bpp */ +- pack = UNICAM_PPM_PACK16; +- } +- +- val = 0; +- set_field(&val, unpack, UNICAM_PUM_MASK); +- set_field(&val, pack, UNICAM_PPM_MASK); +- reg_write(&dev->cfg, UNICAM_IPIPE, val); +-} +- +-static void unicam_cfg_image_id(struct unicam_device *dev) +-{ +- struct unicam_cfg *cfg = &dev->cfg; +- +- if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { +- /* CSI2 mode */ +- reg_write(cfg, UNICAM_IDI0, +- (dev->virtual_channel << 6) | +- dev->node[IMAGE_PAD].fmt->csi_dt); +- } else { +- /* CCP2 mode */ +- reg_write(cfg, UNICAM_IDI0, +- 0x80 | dev->node[IMAGE_PAD].fmt->csi_dt); +- } +-} +- +-static void unicam_enable_ed(struct unicam_device *dev) +-{ +- struct unicam_cfg *cfg = &dev->cfg; +- u32 val = reg_read(cfg, UNICAM_DCS); +- +- set_field(&val, 2, UNICAM_EDL_MASK); +- /* Do not wrap at the end of the embedded data buffer */ +- set_field(&val, 0, UNICAM_DBOB); +- +- reg_write(cfg, UNICAM_DCS, val); +-} +- +-static void unicam_start_rx(struct unicam_device *dev, dma_addr_t *addr) +-{ +- struct unicam_cfg *cfg = &dev->cfg; +- int line_int_freq = dev->node[IMAGE_PAD].v_fmt.fmt.pix.height >> 2; +- unsigned int size, i; +- u32 val; +- +- if (line_int_freq < 128) +- line_int_freq = 128; +- +- /* Enable lane clocks */ +- val = 1; +- for (i = 0; i < dev->active_data_lanes; i++) +- val = val << 2 | 1; +- clk_write(cfg, val); +- +- /* Basic init */ +- reg_write(cfg, UNICAM_CTRL, UNICAM_MEM); +- +- /* Enable analogue control, and leave in reset. */ +- val = UNICAM_AR; +- set_field(&val, 7, UNICAM_CTATADJ_MASK); +- set_field(&val, 7, UNICAM_PTATADJ_MASK); +- reg_write(cfg, UNICAM_ANA, val); +- usleep_range(1000, 2000); +- +- /* Come out of reset */ +- reg_write_field(cfg, UNICAM_ANA, 0, UNICAM_AR); +- +- /* Peripheral reset */ +- reg_write_field(cfg, UNICAM_CTRL, 1, UNICAM_CPR); +- reg_write_field(cfg, UNICAM_CTRL, 0, UNICAM_CPR); +- +- reg_write_field(cfg, UNICAM_CTRL, 0, UNICAM_CPE); +- +- /* Enable Rx control. */ +- val = reg_read(cfg, UNICAM_CTRL); +- if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { +- set_field(&val, UNICAM_CPM_CSI2, UNICAM_CPM_MASK); +- set_field(&val, UNICAM_DCM_STROBE, UNICAM_DCM_MASK); +- } else { +- set_field(&val, UNICAM_CPM_CCP2, UNICAM_CPM_MASK); +- set_field(&val, dev->bus_flags, UNICAM_DCM_MASK); +- } +- /* Packet framer timeout */ +- set_field(&val, 0xf, UNICAM_PFT_MASK); +- set_field(&val, 128, UNICAM_OET_MASK); +- reg_write(cfg, UNICAM_CTRL, val); +- +- reg_write(cfg, UNICAM_IHWIN, 0); +- reg_write(cfg, UNICAM_IVWIN, 0); +- +- /* AXI bus access QoS setup */ +- val = reg_read(&dev->cfg, UNICAM_PRI); +- set_field(&val, 0, UNICAM_BL_MASK); +- set_field(&val, 0, UNICAM_BS_MASK); +- set_field(&val, 0xe, UNICAM_PP_MASK); +- set_field(&val, 8, UNICAM_NP_MASK); +- set_field(&val, 2, UNICAM_PT_MASK); +- set_field(&val, 1, UNICAM_PE); +- reg_write(cfg, UNICAM_PRI, val); +- +- reg_write_field(cfg, UNICAM_ANA, 0, UNICAM_DDL); +- +- /* Always start in trigger frame capture mode (UNICAM_FCM set) */ +- val = UNICAM_FSIE | UNICAM_FEIE | UNICAM_FCM | UNICAM_IBOB; +- set_field(&val, line_int_freq, UNICAM_LCIE_MASK); +- reg_write(cfg, UNICAM_ICTL, val); +- reg_write(cfg, UNICAM_STA, UNICAM_STA_MASK_ALL); +- reg_write(cfg, UNICAM_ISTA, UNICAM_ISTA_MASK_ALL); +- +- /* tclk_term_en */ +- reg_write_field(cfg, UNICAM_CLT, 2, UNICAM_CLT1_MASK); +- /* tclk_settle */ +- reg_write_field(cfg, UNICAM_CLT, 6, UNICAM_CLT2_MASK); +- /* td_term_en */ +- reg_write_field(cfg, UNICAM_DLT, 2, UNICAM_DLT1_MASK); +- /* ths_settle */ +- reg_write_field(cfg, UNICAM_DLT, 6, UNICAM_DLT2_MASK); +- /* trx_enable */ +- reg_write_field(cfg, UNICAM_DLT, 0, UNICAM_DLT3_MASK); +- +- reg_write_field(cfg, UNICAM_CTRL, 0, UNICAM_SOE); +- +- /* Packet compare setup - required to avoid missing frame ends */ +- val = 0; +- set_field(&val, 1, UNICAM_PCE); +- set_field(&val, 1, UNICAM_GI); +- set_field(&val, 1, UNICAM_CPH); +- set_field(&val, 0, UNICAM_PCVC_MASK); +- set_field(&val, 1, UNICAM_PCDT_MASK); +- reg_write(cfg, UNICAM_CMP0, val); +- +- /* Enable clock lane and set up terminations */ +- val = 0; +- if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { +- /* CSI2 */ +- set_field(&val, 1, UNICAM_CLE); +- set_field(&val, 1, UNICAM_CLLPE); +- if (dev->bus_flags & V4L2_MBUS_CSI2_CONTINUOUS_CLOCK) { +- set_field(&val, 1, UNICAM_CLTRE); +- set_field(&val, 1, UNICAM_CLHSE); +- } +- } else { +- /* CCP2 */ +- set_field(&val, 1, UNICAM_CLE); +- set_field(&val, 1, UNICAM_CLHSE); +- set_field(&val, 1, UNICAM_CLTRE); +- } +- reg_write(cfg, UNICAM_CLK, val); +- +- /* +- * Enable required data lanes with appropriate terminations. +- * The same value needs to be written to UNICAM_DATn registers for +- * the active lanes, and 0 for inactive ones. +- */ +- val = 0; +- if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { +- /* CSI2 */ +- set_field(&val, 1, UNICAM_DLE); +- set_field(&val, 1, UNICAM_DLLPE); +- if (dev->bus_flags & V4L2_MBUS_CSI2_CONTINUOUS_CLOCK) { +- set_field(&val, 1, UNICAM_DLTRE); +- set_field(&val, 1, UNICAM_DLHSE); +- } +- } else { +- /* CCP2 */ +- set_field(&val, 1, UNICAM_DLE); +- set_field(&val, 1, UNICAM_DLHSE); +- set_field(&val, 1, UNICAM_DLTRE); +- } +- reg_write(cfg, UNICAM_DAT0, val); +- +- if (dev->active_data_lanes == 1) +- val = 0; +- reg_write(cfg, UNICAM_DAT1, val); +- +- if (dev->max_data_lanes > 2) { +- /* +- * Registers UNICAM_DAT2 and UNICAM_DAT3 only valid if the +- * instance supports more than 2 data lanes. +- */ +- if (dev->active_data_lanes == 2) +- val = 0; +- reg_write(cfg, UNICAM_DAT2, val); +- +- if (dev->active_data_lanes == 3) +- val = 0; +- reg_write(cfg, UNICAM_DAT3, val); +- } +- +- reg_write(&dev->cfg, UNICAM_IBLS, +- dev->node[IMAGE_PAD].v_fmt.fmt.pix.bytesperline); +- size = dev->node[IMAGE_PAD].v_fmt.fmt.pix.sizeimage; +- unicam_wr_dma_addr(&dev->cfg, addr[IMAGE_PAD], size, IMAGE_PAD); +- unicam_set_packing_config(dev); +- unicam_cfg_image_id(dev); +- +- val = reg_read(cfg, UNICAM_MISC); +- set_field(&val, 1, UNICAM_FL0); +- set_field(&val, 1, UNICAM_FL1); +- reg_write(cfg, UNICAM_MISC, val); +- +- if (dev->node[METADATA_PAD].streaming && dev->sensor_embedded_data) { +- size = dev->node[METADATA_PAD].v_fmt.fmt.meta.buffersize; +- unicam_enable_ed(dev); +- unicam_wr_dma_addr(&dev->cfg, addr[METADATA_PAD], size, +- METADATA_PAD); +- } +- +- /* Enable peripheral */ +- reg_write_field(cfg, UNICAM_CTRL, 1, UNICAM_CPE); +- +- /* Load image pointers */ +- reg_write_field(cfg, UNICAM_ICTL, 1, UNICAM_LIP_MASK); +- +- /* Load embedded data buffer pointers if needed */ +- if (dev->node[METADATA_PAD].streaming && dev->sensor_embedded_data) +- reg_write_field(cfg, UNICAM_DCS, 1, UNICAM_LDP); +- +- /* +- * Enable trigger only for the first frame to +- * sync correctly to the FS from the source. +- */ +- reg_write_field(cfg, UNICAM_ICTL, 1, UNICAM_TFC); +-} +- +-static void unicam_disable(struct unicam_device *dev) +-{ +- struct unicam_cfg *cfg = &dev->cfg; +- +- /* Analogue lane control disable */ +- reg_write_field(cfg, UNICAM_ANA, 1, UNICAM_DDL); +- +- /* Stop the output engine */ +- reg_write_field(cfg, UNICAM_CTRL, 1, UNICAM_SOE); +- +- /* Disable the data lanes. */ +- reg_write(cfg, UNICAM_DAT0, 0); +- reg_write(cfg, UNICAM_DAT1, 0); +- +- if (dev->max_data_lanes > 2) { +- reg_write(cfg, UNICAM_DAT2, 0); +- reg_write(cfg, UNICAM_DAT3, 0); +- } +- +- /* Peripheral reset */ +- reg_write_field(cfg, UNICAM_CTRL, 1, UNICAM_CPR); +- usleep_range(50, 100); +- reg_write_field(cfg, UNICAM_CTRL, 0, UNICAM_CPR); +- +- /* Disable peripheral */ +- reg_write_field(cfg, UNICAM_CTRL, 0, UNICAM_CPE); +- +- /* Clear ED setup */ +- reg_write(cfg, UNICAM_DCS, 0); +- +- /* Disable all lane clocks */ +- clk_write(cfg, 0); +-} +- +-static int unicam_start_streaming(struct vb2_queue *vq, unsigned int count) +-{ +- struct unicam_node *node = vb2_get_drv_priv(vq); +- struct unicam_device *dev = node->dev; +- struct unicam_buffer *buf; +- dma_addr_t buffer_addr[MAX_NODES] = { 0 }; +- int num_nodes_streaming; +- unsigned long flags; +- int ret, i; +- +- node->streaming = 1; +- if (!unicam_all_nodes_streaming(dev)) { +- unicam_dbg(3, dev, "Not all nodes are streaming yet."); +- return 0; +- } +- +- dev->sequence = 0; +- ret = unicam_runtime_get(dev); +- if (ret < 0) { +- unicam_dbg(3, dev, "unicam_runtime_get failed\n"); +- return ret; +- } +- +- dev->active_data_lanes = dev->max_data_lanes; +- if (dev->bus_type == V4L2_MBUS_CSI2_DPHY && +- v4l2_subdev_has_op(dev->sensor, video, g_mbus_config)) { +- struct v4l2_mbus_config mbus_config; +- +- ret = v4l2_subdev_call(dev->sensor, video, g_mbus_config, +- &mbus_config); +- if (ret < 0) { +- unicam_dbg(3, dev, "g_mbus_config failed\n"); +- goto err_pm_put; +- } +- +- dev->active_data_lanes = +- (mbus_config.flags & V4L2_MBUS_CSI2_LANE_MASK) >> +- __ffs(V4L2_MBUS_CSI2_LANE_MASK); +- if (!dev->active_data_lanes) +- dev->active_data_lanes = dev->max_data_lanes; +- } +- if (dev->active_data_lanes > dev->max_data_lanes) { +- unicam_err(dev, "Device has requested %u data lanes, which is >%u configured in DT\n", +- dev->active_data_lanes, dev->max_data_lanes); +- ret = -EINVAL; +- goto err_pm_put; +- } +- +- unicam_dbg(1, dev, "Running with %u data lanes\n", +- dev->active_data_lanes); +- +- ret = clk_set_rate(dev->clock, 100 * 1000 * 1000); +- if (ret) { +- unicam_err(dev, "failed to set up clock\n"); +- goto err_pm_put; +- } +- +- ret = clk_prepare_enable(dev->clock); +- if (ret) { +- unicam_err(dev, "Failed to enable CSI clock: %d\n", ret); +- goto err_pm_put; +- } +- +- num_nodes_streaming = unicam_num_nodes_streaming(dev); +- for (i = 0; i < num_nodes_streaming; i++) { +- spin_lock_irqsave(&dev->node[i].dma_queue_lock, flags); +- buf = list_entry(dev->node[i].dma_queue.active.next, +- struct unicam_buffer, list); +- dev->node[i].cur_frm = buf; +- dev->node[i].next_frm = buf; +- list_del(&buf->list); +- spin_unlock_irqrestore(&dev->node[i].dma_queue_lock, flags); +- buffer_addr[i] = +- vb2_dma_contig_plane_dma_addr(&dev->node[i].cur_frm->vb.vb2_buf, +- 0); +- } +- +- unicam_start_rx(dev, buffer_addr); +- +- ret = v4l2_subdev_call(dev->sensor, video, s_stream, 1); +- if (ret < 0) { +- unicam_err(dev, "stream on failed in subdev\n"); +- goto err_disable_unicam; +- } +- +- return 0; +- +-err_disable_unicam: +- node->streaming = 0; +- unicam_disable(dev); +- clk_disable_unprepare(dev->clock); +-err_pm_put: +- unicam_runtime_put(dev); +- +- return ret; +-} +- +-static void unicam_stop_streaming(struct vb2_queue *vq) +-{ +- struct unicam_node *node = vb2_get_drv_priv(vq); +- struct unicam_device *dev = node->dev; +- struct unicam_dmaqueue *dma_q = &node->dma_queue; +- struct unicam_buffer *buf, *tmp; +- unsigned long flags; +- +- node->streaming = 0; +- +- if (node->pad_id == IMAGE_PAD) { +- /* Stop streaming the sensor and disable the peripheral. +- * We cannot continue streaming embedded data with the +- * image pad disabled. +- */ +- if (v4l2_subdev_call(dev->sensor, video, s_stream, 0) < 0) +- unicam_err(dev, "stream off failed in subdev\n"); +- +- unicam_disable(dev); +- clk_disable_unprepare(dev->clock); +- unicam_runtime_put(dev); +- +- } else if (node->pad_id == METADATA_PAD) { +- /* Allow the hardware to spin in the dummy buffer. +- * This is only really needed if the embedded data pad is +- * disabled before the image pad. The 0x3 in the top two bits +- * signifies uncached accesses through the Videocore memory +- * controller. +- */ +- unicam_wr_dma_addr(&dev->cfg, node->dummy_buf_dma_addr, +- DUMMY_BUF_SIZE, METADATA_PAD); +- } +- +- /* Clear all queued buffers for the node */ +- spin_lock_irqsave(&node->dma_queue_lock, flags); +- list_for_each_entry_safe(buf, tmp, &dma_q->active, list) { +- list_del(&buf->list); +- vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); +- } +- +- if (node->cur_frm) +- vb2_buffer_done(&node->cur_frm->vb.vb2_buf, +- VB2_BUF_STATE_ERROR); +- if (node->next_frm && node->cur_frm != node->next_frm) +- vb2_buffer_done(&node->next_frm->vb.vb2_buf, +- VB2_BUF_STATE_ERROR); +- +- node->cur_frm = NULL; +- node->next_frm = NULL; +- spin_unlock_irqrestore(&node->dma_queue_lock, flags); +-} +- +-static int unicam_enum_input(struct file *file, void *priv, +- struct v4l2_input *inp) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- +- if (inp->index != 0) +- return -EINVAL; +- +- inp->type = V4L2_INPUT_TYPE_CAMERA; +- if (v4l2_subdev_has_op(dev->sensor, video, s_dv_timings)) { +- inp->capabilities = V4L2_IN_CAP_DV_TIMINGS; +- inp->std = 0; +- } else if (v4l2_subdev_has_op(dev->sensor, video, s_std)) { +- inp->capabilities = V4L2_IN_CAP_STD; +- if (v4l2_subdev_call(dev->sensor, video, g_tvnorms, &inp->std) +- < 0) +- inp->std = V4L2_STD_ALL; +- } else { +- inp->capabilities = 0; +- inp->std = 0; +- } +- sprintf(inp->name, "Camera 0"); +- return 0; +-} +- +-static int unicam_g_input(struct file *file, void *priv, unsigned int *i) +-{ +- *i = 0; +- +- return 0; +-} +- +-static int unicam_s_input(struct file *file, void *priv, unsigned int i) +-{ +- /* +- * FIXME: Ideally we would like to be able to query the source +- * subdevice for information over the input connectors it supports, +- * and map that through in to a call to video_ops->s_routing. +- * There is no infrastructure support for defining that within +- * devicetree at present. Until that is implemented we can't +- * map a user physical connector number to s_routing input number. +- */ +- if (i > 0) +- return -EINVAL; +- +- return 0; +-} +- +-static int unicam_querystd(struct file *file, void *priv, +- v4l2_std_id *std) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- +- return v4l2_subdev_call(dev->sensor, video, querystd, std); +-} +- +-static int unicam_g_std(struct file *file, void *priv, v4l2_std_id *std) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- +- return v4l2_subdev_call(dev->sensor, video, g_std, std); +-} +- +-static int unicam_s_std(struct file *file, void *priv, v4l2_std_id std) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- int ret; +- v4l2_std_id current_std; +- +- ret = v4l2_subdev_call(dev->sensor, video, g_std, ¤t_std); +- if (ret) +- return ret; +- +- if (std == current_std) +- return 0; +- +- if (vb2_is_busy(&node->buffer_queue)) +- return -EBUSY; +- +- ret = v4l2_subdev_call(dev->sensor, video, s_std, std); +- +- /* Force recomputation of bytesperline */ +- node->v_fmt.fmt.pix.bytesperline = 0; +- +- unicam_reset_format(node); +- +- return ret; +-} +- +-static int unicam_s_edid(struct file *file, void *priv, struct v4l2_edid *edid) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- +- return v4l2_subdev_call(dev->sensor, pad, set_edid, edid); +-} +- +-static int unicam_g_edid(struct file *file, void *priv, struct v4l2_edid *edid) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- +- return v4l2_subdev_call(dev->sensor, pad, get_edid, edid); +-} +- +-static int unicam_s_selection(struct file *file, void *priv, +- struct v4l2_selection *sel) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- struct v4l2_subdev_selection sdsel = { +- .which = V4L2_SUBDEV_FORMAT_ACTIVE, +- .target = sel->target, +- .flags = sel->flags, +- .r = sel->r, +- }; +- +- return v4l2_subdev_call(dev->sensor, pad, set_selection, NULL, &sdsel); +-} +- +-static int unicam_g_selection(struct file *file, void *priv, +- struct v4l2_selection *sel) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- struct v4l2_subdev_selection sdsel = { +- .which = V4L2_SUBDEV_FORMAT_ACTIVE, +- .target = sel->target, +- }; +- int ret; +- +- ret = v4l2_subdev_call(dev->sensor, pad, get_selection, NULL, &sdsel); +- if (!ret) +- sel->r = sdsel.r; +- +- return ret; +-} +- +-static int unicam_enum_framesizes(struct file *file, void *priv, +- struct v4l2_frmsizeenum *fsize) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- const struct unicam_fmt *fmt; +- struct v4l2_subdev_frame_size_enum fse; +- int ret; +- +- if (node->pad_id == IMAGE_PAD) { +- /* check for valid format */ +- fmt = find_format_by_pix(dev, fsize->pixel_format); +- if (!fmt) { +- unicam_dbg(3, dev, "Invalid pixel code: %x\n", +- fsize->pixel_format); +- return -EINVAL; +- } +- fse.code = fmt->code; +- } else { +- /* This pad is for embedded data, so just set the format */ +- fse.code = MEDIA_BUS_FMT_SENSOR_DATA; +- } +- +- fse.which = V4L2_SUBDEV_FORMAT_ACTIVE; +- fse.index = fsize->index; +- fse.pad = node->pad_id; +- +- ret = v4l2_subdev_call(dev->sensor, pad, enum_frame_size, NULL, &fse); +- if (ret) +- return ret; +- +- unicam_dbg(1, dev, "%s: index: %d code: %x W:[%d,%d] H:[%d,%d]\n", +- __func__, fse.index, fse.code, fse.min_width, fse.max_width, +- fse.min_height, fse.max_height); +- +- fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE; +- fsize->discrete.width = fse.max_width; +- fsize->discrete.height = fse.max_height; +- +- return 0; +-} +- +-static int unicam_enum_frameintervals(struct file *file, void *priv, +- struct v4l2_frmivalenum *fival) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- const struct unicam_fmt *fmt; +- struct v4l2_subdev_frame_interval_enum fie = { +- .index = fival->index, +- .width = fival->width, +- .height = fival->height, +- .which = V4L2_SUBDEV_FORMAT_ACTIVE, +- }; +- int ret; +- +- fmt = find_format_by_pix(dev, fival->pixel_format); +- if (!fmt) +- return -EINVAL; +- +- fie.code = fmt->code; +- ret = v4l2_subdev_call(dev->sensor, pad, enum_frame_interval, +- NULL, &fie); +- if (ret) +- return ret; +- +- fival->type = V4L2_FRMIVAL_TYPE_DISCRETE; +- fival->discrete = fie.interval; +- +- return 0; +-} +- +-static int unicam_g_parm(struct file *file, void *fh, struct v4l2_streamparm *a) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- +- return v4l2_g_parm_cap(video_devdata(file), dev->sensor, a); +-} +- +-static int unicam_s_parm(struct file *file, void *fh, struct v4l2_streamparm *a) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- +- return v4l2_s_parm_cap(video_devdata(file), dev->sensor, a); +-} +- +-static int unicam_g_dv_timings(struct file *file, void *priv, +- struct v4l2_dv_timings *timings) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- +- return v4l2_subdev_call(dev->sensor, video, g_dv_timings, timings); +-} +- +-static int unicam_s_dv_timings(struct file *file, void *priv, +- struct v4l2_dv_timings *timings) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- struct v4l2_dv_timings current_timings; +- int ret; +- +- ret = v4l2_subdev_call(dev->sensor, video, g_dv_timings, +- ¤t_timings); +- +- if (v4l2_match_dv_timings(timings, ¤t_timings, 0, false)) +- return 0; +- +- if (vb2_is_busy(&node->buffer_queue)) +- return -EBUSY; +- +- ret = v4l2_subdev_call(dev->sensor, video, s_dv_timings, timings); +- +- /* Force recomputation of bytesperline */ +- node->v_fmt.fmt.pix.bytesperline = 0; +- +- unicam_reset_format(node); +- +- return ret; +-} +- +-static int unicam_query_dv_timings(struct file *file, void *priv, +- struct v4l2_dv_timings *timings) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- +- return v4l2_subdev_call(dev->sensor, video, query_dv_timings, timings); +-} +- +-static int unicam_enum_dv_timings(struct file *file, void *priv, +- struct v4l2_enum_dv_timings *timings) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- +- return v4l2_subdev_call(dev->sensor, pad, enum_dv_timings, timings); +-} +- +-static int unicam_dv_timings_cap(struct file *file, void *priv, +- struct v4l2_dv_timings_cap *cap) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- +- return v4l2_subdev_call(dev->sensor, pad, dv_timings_cap, cap); +-} +- +-static int unicam_subscribe_event(struct v4l2_fh *fh, +- const struct v4l2_event_subscription *sub) +-{ +- switch (sub->type) { +- case V4L2_EVENT_FRAME_SYNC: +- return v4l2_event_subscribe(fh, sub, 2, NULL); +- case V4L2_EVENT_SOURCE_CHANGE: +- return v4l2_event_subscribe(fh, sub, 4, NULL); +- } +- +- return v4l2_ctrl_subscribe_event(fh, sub); +-} +- +-static int unicam_log_status(struct file *file, void *fh) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- struct unicam_cfg *cfg = &dev->cfg; +- u32 reg; +- +- /* status for sub devices */ +- v4l2_device_call_all(&dev->v4l2_dev, 0, core, log_status); +- +- unicam_info(dev, "-----Receiver status-----\n"); +- unicam_info(dev, "V4L2 width/height: %ux%u\n", +- node->v_fmt.fmt.pix.width, node->v_fmt.fmt.pix.height); +- unicam_info(dev, "Mediabus format: %08x\n", node->fmt->code); +- unicam_info(dev, "V4L2 format: %08x\n", +- node->v_fmt.fmt.pix.pixelformat); +- reg = reg_read(&dev->cfg, UNICAM_IPIPE); +- unicam_info(dev, "Unpacking/packing: %u / %u\n", +- get_field(reg, UNICAM_PUM_MASK), +- get_field(reg, UNICAM_PPM_MASK)); +- unicam_info(dev, "----Live data----\n"); +- unicam_info(dev, "Programmed stride: %4u\n", +- reg_read(cfg, UNICAM_IBLS)); +- unicam_info(dev, "Detected resolution: %ux%u\n", +- reg_read(cfg, UNICAM_IHSTA), +- reg_read(cfg, UNICAM_IVSTA)); +- unicam_info(dev, "Write pointer: %08x\n", +- reg_read(cfg, UNICAM_IBWP)); +- +- return 0; +-} +- +-static void unicam_notify(struct v4l2_subdev *sd, +- unsigned int notification, void *arg) +-{ +- struct unicam_device *dev = +- container_of(sd->v4l2_dev, struct unicam_device, v4l2_dev); +- +- switch (notification) { +- case V4L2_DEVICE_NOTIFY_EVENT: +- v4l2_event_queue(&dev->node[IMAGE_PAD].video_dev, arg); +- break; +- default: +- break; +- } +-} +- +-static const struct vb2_ops unicam_video_qops = { +- .wait_prepare = vb2_ops_wait_prepare, +- .wait_finish = vb2_ops_wait_finish, +- .queue_setup = unicam_queue_setup, +- .buf_prepare = unicam_buffer_prepare, +- .buf_queue = unicam_buffer_queue, +- .start_streaming = unicam_start_streaming, +- .stop_streaming = unicam_stop_streaming, +-}; +- +-/* +- * unicam_open : This function is based on the v4l2_fh_open helper function. +- * It has been augmented to handle sensor subdevice power management, +- */ +-static int unicam_open(struct file *file) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- int ret; +- +- mutex_lock(&node->lock); +- +- ret = v4l2_fh_open(file); +- if (ret) { +- unicam_err(dev, "v4l2_fh_open failed\n"); +- goto unlock; +- } +- +- node->open++; +- +- if (!v4l2_fh_is_singular_file(file)) +- goto unlock; +- +- ret = v4l2_subdev_call(dev->sensor, core, s_power, 1); +- if (ret < 0 && ret != -ENOIOCTLCMD) { +- v4l2_fh_release(file); +- node->open--; +- goto unlock; +- } +- +- ret = 0; +- +-unlock: +- mutex_unlock(&node->lock); +- return ret; +-} +- +-static int unicam_release(struct file *file) +-{ +- struct unicam_node *node = video_drvdata(file); +- struct unicam_device *dev = node->dev; +- struct v4l2_subdev *sd = dev->sensor; +- bool fh_singular; +- int ret; +- +- mutex_lock(&node->lock); +- +- fh_singular = v4l2_fh_is_singular_file(file); +- +- ret = _vb2_fop_release(file, NULL); +- +- if (fh_singular) +- v4l2_subdev_call(sd, core, s_power, 0); +- +- node->open--; +- mutex_unlock(&node->lock); +- +- return ret; +-} +- +-/* unicam capture driver file operations */ +-static const struct v4l2_file_operations unicam_fops = { +- .owner = THIS_MODULE, +- .open = unicam_open, +- .release = unicam_release, +- .read = vb2_fop_read, +- .poll = vb2_fop_poll, +- .unlocked_ioctl = video_ioctl2, +- .mmap = vb2_fop_mmap, +-}; +- +-/* unicam capture ioctl operations */ +-static const struct v4l2_ioctl_ops unicam_ioctl_ops = { +- .vidioc_querycap = unicam_querycap, +- .vidioc_enum_fmt_vid_cap = unicam_enum_fmt_vid_cap, +- .vidioc_g_fmt_vid_cap = unicam_g_fmt_vid_cap, +- .vidioc_s_fmt_vid_cap = unicam_s_fmt_vid_cap, +- .vidioc_try_fmt_vid_cap = unicam_try_fmt_vid_cap, +- +- .vidioc_enum_fmt_meta_cap = unicam_enum_fmt_meta_cap, +- .vidioc_g_fmt_meta_cap = unicam_g_fmt_meta_cap, +- .vidioc_s_fmt_meta_cap = unicam_s_fmt_meta_cap, +- .vidioc_try_fmt_meta_cap = unicam_try_fmt_meta_cap, +- +- .vidioc_enum_input = unicam_enum_input, +- .vidioc_g_input = unicam_g_input, +- .vidioc_s_input = unicam_s_input, +- +- .vidioc_querystd = unicam_querystd, +- .vidioc_s_std = unicam_s_std, +- .vidioc_g_std = unicam_g_std, +- +- .vidioc_g_edid = unicam_g_edid, +- .vidioc_s_edid = unicam_s_edid, +- +- .vidioc_enum_framesizes = unicam_enum_framesizes, +- .vidioc_enum_frameintervals = unicam_enum_frameintervals, +- +- .vidioc_g_selection = unicam_g_selection, +- .vidioc_s_selection = unicam_s_selection, +- +- .vidioc_g_parm = unicam_g_parm, +- .vidioc_s_parm = unicam_s_parm, +- +- .vidioc_s_dv_timings = unicam_s_dv_timings, +- .vidioc_g_dv_timings = unicam_g_dv_timings, +- .vidioc_query_dv_timings = unicam_query_dv_timings, +- .vidioc_enum_dv_timings = unicam_enum_dv_timings, +- .vidioc_dv_timings_cap = unicam_dv_timings_cap, +- +- .vidioc_reqbufs = vb2_ioctl_reqbufs, +- .vidioc_create_bufs = vb2_ioctl_create_bufs, +- .vidioc_prepare_buf = vb2_ioctl_prepare_buf, +- .vidioc_querybuf = vb2_ioctl_querybuf, +- .vidioc_qbuf = vb2_ioctl_qbuf, +- .vidioc_dqbuf = vb2_ioctl_dqbuf, +- .vidioc_expbuf = vb2_ioctl_expbuf, +- .vidioc_streamon = vb2_ioctl_streamon, +- .vidioc_streamoff = vb2_ioctl_streamoff, +- +- .vidioc_log_status = unicam_log_status, +- .vidioc_subscribe_event = unicam_subscribe_event, +- .vidioc_unsubscribe_event = v4l2_event_unsubscribe, +-}; +- +-static int +-unicam_async_bound(struct v4l2_async_notifier *notifier, +- struct v4l2_subdev *subdev, +- struct v4l2_async_subdev *asd) +-{ +- struct unicam_device *unicam = container_of(notifier->v4l2_dev, +- struct unicam_device, v4l2_dev); +- +- if (unicam->sensor) { +- unicam_info(unicam, "Rejecting subdev %s (Already set!!)", +- subdev->name); +- return 0; +- } +- +- unicam->sensor = subdev; +- unicam_dbg(1, unicam, "Using sensor %s for capture\n", subdev->name); +- +- return 0; +-} +- +-static int register_node(struct unicam_device *unicam, struct unicam_node *node, +- enum v4l2_buf_type type, int pad_id) +-{ +- struct video_device *vdev; +- struct vb2_queue *q; +- struct v4l2_mbus_framefmt mbus_fmt = {0}; +- const struct unicam_fmt *fmt; +- int ret; +- +- if (unicam->sensor_embedded_data || pad_id != METADATA_PAD) { +- ret = __subdev_get_format(unicam, &mbus_fmt, pad_id); +- if (ret) { +- unicam_err(unicam, "Failed to get_format - ret %d\n", +- ret); +- return ret; +- } +- +- fmt = find_format_by_code(mbus_fmt.code); +- if (!fmt) { +- /* Find the first format that the sensor and unicam both +- * support +- */ +- fmt = get_first_supported_format(unicam); +- +- if (!fmt) +- /* No compatible formats */ +- return -EINVAL; +- +- mbus_fmt.code = fmt->code; +- ret = __subdev_set_format(unicam, &mbus_fmt, pad_id); +- if (ret) +- return -EINVAL; +- } +- if (mbus_fmt.field != V4L2_FIELD_NONE) { +- /* Interlaced not supported - disable it now. */ +- mbus_fmt.field = V4L2_FIELD_NONE; +- ret = __subdev_set_format(unicam, &mbus_fmt, pad_id); +- if (ret) +- return -EINVAL; +- } +- } else { +- /* Fix this node format as embedded data. */ +- fmt = find_format_by_code(MEDIA_BUS_FMT_SENSOR_DATA); +- } +- +- node->dev = unicam; +- node->pad_id = pad_id; +- node->fmt = fmt; +- if (fmt->fourcc) { +- if (fmt->fourcc != V4L2_META_FMT_SENSOR_DATA) +- node->v_fmt.fmt.pix.pixelformat = fmt->fourcc; +- else +- node->v_fmt.fmt.meta.dataformat = fmt->fourcc; +- } else { +- node->v_fmt.fmt.pix.pixelformat = fmt->repacked_fourcc; +- } +- +- /* Read current subdev format */ +- unicam_reset_format(node); +- +- if (v4l2_subdev_has_op(unicam->sensor, video, s_std)) { +- v4l2_std_id tvnorms; +- +- if (WARN_ON(!v4l2_subdev_has_op(unicam->sensor, video, +- g_tvnorms))) +- /* +- * Subdevice should not advertise s_std but not +- * g_tvnorms +- */ +- return -EINVAL; +- +- ret = v4l2_subdev_call(unicam->sensor, video, +- g_tvnorms, &tvnorms); +- if (WARN_ON(ret)) +- return -EINVAL; +- node->video_dev.tvnorms |= tvnorms; +- } +- +- spin_lock_init(&node->dma_queue_lock); +- mutex_init(&node->lock); +- +- vdev = &node->video_dev; +- if (pad_id == IMAGE_PAD) { +- /* Add controls from the subdevice */ +- ret = v4l2_ctrl_add_handler(&node->ctrl_handler, +- unicam->sensor->ctrl_handler, NULL, +- true); +- if (ret < 0) +- return ret; +- +- /* +- * If the sensor subdevice has any controls, associate the node +- * with the ctrl handler to allow access from userland. +- */ +- if (!list_empty(&node->ctrl_handler.ctrls)) +- vdev->ctrl_handler = &node->ctrl_handler; +- } +- +- q = &node->buffer_queue; +- q->type = type; +- q->io_modes = VB2_MMAP | VB2_DMABUF | VB2_READ; +- q->drv_priv = node; +- q->ops = &unicam_video_qops; +- q->mem_ops = &vb2_dma_contig_memops; +- q->buf_struct_size = sizeof(struct unicam_buffer); +- q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC; +- q->lock = &node->lock; +- q->min_buffers_needed = 1; +- q->dev = &unicam->pdev->dev; +- +- ret = vb2_queue_init(q); +- if (ret) { +- unicam_err(unicam, "vb2_queue_init() failed\n"); +- return ret; +- } +- +- INIT_LIST_HEAD(&node->dma_queue.active); +- +- vdev->release = video_device_release_empty; +- vdev->fops = &unicam_fops; +- vdev->ioctl_ops = &unicam_ioctl_ops; +- vdev->v4l2_dev = &unicam->v4l2_dev; +- vdev->vfl_dir = VFL_DIR_RX; +- vdev->queue = q; +- vdev->lock = &node->lock; +- vdev->device_caps = (pad_id == IMAGE_PAD) ? +- (V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING) : +- (V4L2_CAP_META_CAPTURE | V4L2_CAP_STREAMING); +- +- /* Define the device names */ +- snprintf(vdev->name, sizeof(vdev->name), "%s-%s", UNICAM_MODULE_NAME, +- node->pad_id == IMAGE_PAD ? "image" : "embedded"); +- +- video_set_drvdata(vdev, node); +- vdev->entity.flags |= MEDIA_ENT_FL_DEFAULT; +- +- node->dummy_buf_cpu_addr = dma_alloc_coherent(&unicam->pdev->dev, +- DUMMY_BUF_SIZE, +- &node->dummy_buf_dma_addr, +- GFP_ATOMIC); +- if (!node->dummy_buf_cpu_addr) { +- unicam_err(unicam, "Unable to allocate dummy buffer.\n"); +- return -ENOMEM; +- } +- +- if (node->pad_id == METADATA_PAD) { +- v4l2_disable_ioctl(vdev, VIDIOC_DQEVENT); +- v4l2_disable_ioctl(vdev, VIDIOC_SUBSCRIBE_EVENT); +- v4l2_disable_ioctl(vdev, VIDIOC_UNSUBSCRIBE_EVENT); +- } +- if (node->pad_id == METADATA_PAD || +- !v4l2_subdev_has_op(unicam->sensor, video, s_std)) { +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_STD); +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_STD); +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_ENUMSTD); +- } +- if (node->pad_id == METADATA_PAD || +- !v4l2_subdev_has_op(unicam->sensor, video, querystd)) +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_QUERYSTD); +- if (node->pad_id == METADATA_PAD || +- !v4l2_subdev_has_op(unicam->sensor, video, s_dv_timings)) { +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_EDID); +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_EDID); +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_DV_TIMINGS_CAP); +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_DV_TIMINGS); +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_DV_TIMINGS); +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_ENUM_DV_TIMINGS); +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_QUERY_DV_TIMINGS); +- } +- if (node->pad_id == METADATA_PAD || +- !v4l2_subdev_has_op(unicam->sensor, pad, enum_frame_interval)) +- v4l2_disable_ioctl(&node->video_dev, +- VIDIOC_ENUM_FRAMEINTERVALS); +- if (node->pad_id == METADATA_PAD || +- !v4l2_subdev_has_op(unicam->sensor, video, g_frame_interval)) +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_PARM); +- if (node->pad_id == METADATA_PAD || +- !v4l2_subdev_has_op(unicam->sensor, video, s_frame_interval)) +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_PARM); +- +- if (node->pad_id == METADATA_PAD || +- !v4l2_subdev_has_op(unicam->sensor, pad, enum_frame_size)) +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_ENUM_FRAMESIZES); +- +- if (node->pad_id == METADATA_PAD || +- !v4l2_subdev_has_op(unicam->sensor, pad, set_selection)) +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_SELECTION); +- +- if (node->pad_id == METADATA_PAD || +- !v4l2_subdev_has_op(unicam->sensor, pad, get_selection)) +- v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_SELECTION); +- +- ret = video_register_device(vdev, VFL_TYPE_VIDEO, -1); +- if (ret) { +- unicam_err(unicam, "Unable to register video device.\n"); +- return ret; +- } +- node->registered = 1; +- +- if (unicam->sensor_embedded_data) { +- ret = media_create_pad_link(&unicam->sensor->entity, pad_id, +- &node->video_dev.entity, 0, +- MEDIA_LNK_FL_ENABLED | +- MEDIA_LNK_FL_IMMUTABLE); +- if (ret) +- unicam_err(unicam, "Unable to create pad links.\n"); +- } +- +- return ret; +-} +- +-static void unregister_nodes(struct unicam_device *unicam) +-{ +- struct unicam_node *node; +- int i; +- +- for (i = 0; i < MAX_NODES; i++) { +- node = &unicam->node[i]; +- if (node->dummy_buf_cpu_addr) { +- dma_free_coherent(&unicam->pdev->dev, DUMMY_BUF_SIZE, +- node->dummy_buf_cpu_addr, +- node->dummy_buf_dma_addr); +- } +- if (node->registered) { +- video_unregister_device(&node->video_dev); +- node->registered = 0; +- } +- } +-} +- +-static int unicam_probe_complete(struct unicam_device *unicam) +-{ +- int ret; +- +- v4l2_set_subdev_hostdata(unicam->sensor, unicam); +- +- unicam->v4l2_dev.notify = unicam_notify; +- +- unicam->sensor_config = v4l2_subdev_alloc_pad_config(unicam->sensor); +- if (!unicam->sensor_config) +- return -ENOMEM; +- +- unicam->sensor_embedded_data = (unicam->sensor->entity.num_pads >= 2); +- +- ret = register_node(unicam, &unicam->node[IMAGE_PAD], +- V4L2_BUF_TYPE_VIDEO_CAPTURE, IMAGE_PAD); +- if (ret) { +- unicam_err(unicam, "Unable to register subdev node 0.\n"); +- goto unregister; +- } +- +- ret = register_node(unicam, &unicam->node[METADATA_PAD], +- V4L2_BUF_TYPE_META_CAPTURE, METADATA_PAD); +- if (ret) { +- unicam_err(unicam, "Unable to register subdev node 1.\n"); +- goto unregister; +- } +- +- ret = v4l2_device_register_ro_subdev_nodes(&unicam->v4l2_dev); +- if (ret) { +- unicam_err(unicam, "Unable to register subdev nodes.\n"); +- goto unregister; +- } +- +- return 0; +- +-unregister: +- unregister_nodes(unicam); +- +- return ret; +-} +- +-static int unicam_async_complete(struct v4l2_async_notifier *notifier) +-{ +- struct unicam_device *unicam = container_of(notifier->v4l2_dev, +- struct unicam_device, v4l2_dev); +- +- return unicam_probe_complete(unicam); +-} +- +-static const struct v4l2_async_notifier_operations unicam_async_ops = { +- .bound = unicam_async_bound, +- .complete = unicam_async_complete, +-}; +- +-static int of_unicam_connect_subdevs(struct unicam_device *dev) +-{ +- struct platform_device *pdev = dev->pdev; +- struct device_node *parent, *ep_node = NULL, *remote_ep = NULL, +- *sensor_node = NULL; +- struct v4l2_fwnode_endpoint *ep; +- struct v4l2_async_subdev *asd; +- unsigned int peripheral_data_lanes; +- int ret = -EINVAL; +- unsigned int lane; +- +- parent = pdev->dev.of_node; +- +- asd = &dev->asd; +- ep = &dev->endpoint; +- +- ep_node = of_graph_get_next_endpoint(parent, NULL); +- if (!ep_node) { +- unicam_dbg(3, dev, "can't get next endpoint\n"); +- goto cleanup_exit; +- } +- +- unicam_dbg(3, dev, "ep_node is %s\n", ep_node->name); +- +- v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep_node), ep); +- +- for (lane = 0; lane < ep->bus.mipi_csi2.num_data_lanes; lane++) { +- if (ep->bus.mipi_csi2.data_lanes[lane] != lane + 1) { +- unicam_err(dev, "Local endpoint - data lane reordering not supported\n"); +- goto cleanup_exit; +- } +- } +- +- peripheral_data_lanes = ep->bus.mipi_csi2.num_data_lanes; +- +- sensor_node = of_graph_get_remote_port_parent(ep_node); +- if (!sensor_node) { +- unicam_dbg(3, dev, "can't get remote parent\n"); +- goto cleanup_exit; +- } +- unicam_dbg(3, dev, "sensor_node is %s\n", sensor_node->name); +- asd->match_type = V4L2_ASYNC_MATCH_FWNODE; +- asd->match.fwnode = of_fwnode_handle(sensor_node); +- +- remote_ep = of_graph_get_remote_endpoint(ep_node); +- if (!remote_ep) { +- unicam_dbg(3, dev, "can't get remote-endpoint\n"); +- goto cleanup_exit; +- } +- unicam_dbg(3, dev, "remote_ep is %s\n", remote_ep->name); +- v4l2_fwnode_endpoint_parse(of_fwnode_handle(remote_ep), ep); +- unicam_dbg(3, dev, "parsed remote_ep to endpoint. nr_of_link_frequencies %u, bus_type %u\n", +- ep->nr_of_link_frequencies, ep->bus_type); +- +- switch (ep->bus_type) { +- case V4L2_MBUS_CSI2_DPHY: +- if (ep->bus.mipi_csi2.num_data_lanes > +- peripheral_data_lanes) { +- unicam_err(dev, "Subdevice %s wants too many data lanes (%u > %u)\n", +- sensor_node->name, +- ep->bus.mipi_csi2.num_data_lanes, +- peripheral_data_lanes); +- goto cleanup_exit; +- } +- for (lane = 0; +- lane < ep->bus.mipi_csi2.num_data_lanes; +- lane++) { +- if (ep->bus.mipi_csi2.data_lanes[lane] != lane + 1) { +- unicam_err(dev, "Subdevice %s - incompatible data lane config\n", +- sensor_node->name); +- goto cleanup_exit; +- } +- } +- dev->max_data_lanes = ep->bus.mipi_csi2.num_data_lanes; +- dev->bus_flags = ep->bus.mipi_csi2.flags; +- break; +- case V4L2_MBUS_CCP2: +- if (ep->bus.mipi_csi1.clock_lane != 0 || +- ep->bus.mipi_csi1.data_lane != 1) { +- unicam_err(dev, "Subdevice %s incompatible lane config\n", +- sensor_node->name); +- goto cleanup_exit; +- } +- dev->max_data_lanes = 1; +- dev->bus_flags = ep->bus.mipi_csi1.strobe; +- break; +- default: +- /* Unsupported bus type */ +- unicam_err(dev, "sub-device %s is not a CSI2 or CCP2 device %d\n", +- sensor_node->name, ep->bus_type); +- goto cleanup_exit; +- } +- +- /* Store bus type - CSI2 or CCP2 */ +- dev->bus_type = ep->bus_type; +- unicam_dbg(3, dev, "bus_type is %d\n", dev->bus_type); +- +- /* Store Virtual Channel number */ +- dev->virtual_channel = ep->base.id; +- +- unicam_dbg(3, dev, "v4l2-endpoint: %s\n", +- dev->bus_type == V4L2_MBUS_CSI2_DPHY ? "CSI2" : "CCP2"); +- unicam_dbg(3, dev, "Virtual Channel=%d\n", dev->virtual_channel); +- if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) +- unicam_dbg(3, dev, "flags=0x%08x\n", ep->bus.mipi_csi2.flags); +- unicam_dbg(3, dev, "num_data_lanes=%d\n", dev->max_data_lanes); +- +- unicam_dbg(1, dev, "found sub-device %s\n", sensor_node->name); +- +- v4l2_async_notifier_init(&dev->notifier); +- +- ret = v4l2_async_notifier_add_subdev(&dev->notifier, asd); +- if (ret) { +- unicam_err(dev, "Error adding subdevice - ret %d\n", ret); +- goto cleanup_exit; +- } +- +- dev->notifier.ops = &unicam_async_ops; +- ret = v4l2_async_notifier_register(&dev->v4l2_dev, +- &dev->notifier); +- if (ret) { +- unicam_err(dev, "Error registering async notifier - ret %d\n", +- ret); +- ret = -EINVAL; +- } +- +-cleanup_exit: +- if (remote_ep) +- of_node_put(remote_ep); +- if (sensor_node) +- of_node_put(sensor_node); +- if (ep_node) +- of_node_put(ep_node); +- +- return ret; +-} +- +-static int unicam_probe(struct platform_device *pdev) +-{ +- struct unicam_cfg *unicam_cfg; +- struct unicam_device *unicam; +- struct v4l2_ctrl_handler *hdl; +- struct resource *res; +- int ret; +- +- unicam = devm_kzalloc(&pdev->dev, sizeof(*unicam), GFP_KERNEL); +- if (!unicam) +- return -ENOMEM; +- +- unicam->pdev = pdev; +- unicam_cfg = &unicam->cfg; +- +- res = platform_get_resource(pdev, IORESOURCE_MEM, 0); +- unicam_cfg->base = devm_ioremap_resource(&pdev->dev, res); +- if (IS_ERR(unicam_cfg->base)) { +- unicam_err(unicam, "Failed to get main io block\n"); +- return PTR_ERR(unicam_cfg->base); +- } +- +- res = platform_get_resource(pdev, IORESOURCE_MEM, 1); +- unicam_cfg->clk_gate_base = devm_ioremap_resource(&pdev->dev, res); +- if (IS_ERR(unicam_cfg->clk_gate_base)) { +- unicam_err(unicam, "Failed to get 2nd io block\n"); +- return PTR_ERR(unicam_cfg->clk_gate_base); +- } +- +- unicam->clock = devm_clk_get(&pdev->dev, "lp"); +- if (IS_ERR(unicam->clock)) { +- unicam_err(unicam, "Failed to get clock\n"); +- return PTR_ERR(unicam->clock); +- } +- +- ret = platform_get_irq(pdev, 0); +- if (ret <= 0) { +- dev_err(&pdev->dev, "No IRQ resource\n"); +- return -ENODEV; +- } +- +- ret = devm_request_irq(&pdev->dev, ret, unicam_isr, 0, +- "unicam_capture0", unicam); +- if (ret) { +- dev_err(&pdev->dev, "Unable to request interrupt\n"); +- return -EINVAL; +- } +- +- unicam->mdev.dev = &pdev->dev; +- strscpy(unicam->mdev.model, UNICAM_MODULE_NAME, +- sizeof(unicam->mdev.model)); +- strscpy(unicam->mdev.serial, "", sizeof(unicam->mdev.serial)); +- snprintf(unicam->mdev.bus_info, sizeof(unicam->mdev.bus_info), +- "platform:%s %s", +- pdev->dev.driver->name, dev_name(&pdev->dev)); +- unicam->mdev.hw_revision = 1; +- +- media_entity_pads_init(&unicam->node[IMAGE_PAD].video_dev.entity, 1, +- &unicam->node[IMAGE_PAD].pad); +- media_entity_pads_init(&unicam->node[METADATA_PAD].video_dev.entity, 1, +- &unicam->node[METADATA_PAD].pad); +- media_device_init(&unicam->mdev); +- +- unicam->v4l2_dev.mdev = &unicam->mdev; +- +- ret = v4l2_device_register(&pdev->dev, &unicam->v4l2_dev); +- if (ret) { +- unicam_err(unicam, +- "Unable to register v4l2 device.\n"); +- goto media_cleanup; +- } +- +- ret = media_device_register(&unicam->mdev); +- if (ret < 0) { +- unicam_err(unicam, +- "Unable to register media-controller device.\n"); +- goto probe_out_v4l2_unregister; +- } +- +- /* Reserve space for the controls */ +- hdl = &unicam->node[IMAGE_PAD].ctrl_handler; +- ret = v4l2_ctrl_handler_init(hdl, 16); +- if (ret < 0) +- goto media_unregister; +- +- /* set the driver data in platform device */ +- platform_set_drvdata(pdev, unicam); +- +- ret = of_unicam_connect_subdevs(unicam); +- if (ret) { +- dev_err(&pdev->dev, "Failed to connect subdevs\n"); +- goto free_hdl; +- } +- +- /* Enable the block power domain */ +- pm_runtime_enable(&pdev->dev); +- +- return 0; +- +-free_hdl: +- v4l2_ctrl_handler_free(hdl); +-media_unregister: +- media_device_unregister(&unicam->mdev); +-probe_out_v4l2_unregister: +- v4l2_device_unregister(&unicam->v4l2_dev); +-media_cleanup: +- media_device_cleanup(&unicam->mdev); +- +- return ret; +-} +- +-static int unicam_remove(struct platform_device *pdev) +-{ +- struct unicam_device *unicam = platform_get_drvdata(pdev); +- +- unicam_dbg(2, unicam, "%s\n", __func__); +- +- pm_runtime_disable(&pdev->dev); +- +- v4l2_async_notifier_unregister(&unicam->notifier); +- v4l2_ctrl_handler_free(&unicam->node[IMAGE_PAD].ctrl_handler); +- v4l2_device_unregister(&unicam->v4l2_dev); +- unregister_nodes(unicam); +- if (unicam->sensor_config) +- v4l2_subdev_free_pad_config(unicam->sensor_config); +- media_device_unregister(&unicam->mdev); +- media_device_cleanup(&unicam->mdev); +- +- return 0; +-} +- +-static const struct of_device_id unicam_of_match[] = { +- { .compatible = "brcm,bcm2835-unicam", }, +- { /* sentinel */ }, +-}; +-MODULE_DEVICE_TABLE(of, unicam_of_match); +- +-static struct platform_driver unicam_driver = { +- .probe = unicam_probe, +- .remove = unicam_remove, +- .driver = { +- .name = UNICAM_MODULE_NAME, +- .of_match_table = of_match_ptr(unicam_of_match), +- }, +-}; +- +-module_platform_driver(unicam_driver); +- +-MODULE_AUTHOR("Dave Stevenson "); +-MODULE_DESCRIPTION("BCM2835 Unicam driver"); +-MODULE_LICENSE("GPL"); +-MODULE_VERSION(UNICAM_VERSION); +--- a/drivers/media/platform/bcm2835/vc4-regs-unicam.h ++++ /dev/null +@@ -1,253 +0,0 @@ +-/* SPDX-License-Identifier: GPL-2.0-only */ +- +-/* +- * Copyright (C) 2017-2020 Raspberry Pi Trading. +- * Dave Stevenson +- */ +- +-#ifndef VC4_REGS_UNICAM_H +-#define VC4_REGS_UNICAM_H +- +-/* +- * The following values are taken from files found within the code drop +- * made by Broadcom for the BCM21553 Graphics Driver, predominantly in +- * brcm_usrlib/dag/vmcsx/vcinclude/hardware_vc4.h. +- * They have been modified to be only the register offset. +- */ +-#define UNICAM_CTRL 0x000 +-#define UNICAM_STA 0x004 +-#define UNICAM_ANA 0x008 +-#define UNICAM_PRI 0x00c +-#define UNICAM_CLK 0x010 +-#define UNICAM_CLT 0x014 +-#define UNICAM_DAT0 0x018 +-#define UNICAM_DAT1 0x01c +-#define UNICAM_DAT2 0x020 +-#define UNICAM_DAT3 0x024 +-#define UNICAM_DLT 0x028 +-#define UNICAM_CMP0 0x02c +-#define UNICAM_CMP1 0x030 +-#define UNICAM_CAP0 0x034 +-#define UNICAM_CAP1 0x038 +-#define UNICAM_ICTL 0x100 +-#define UNICAM_ISTA 0x104 +-#define UNICAM_IDI0 0x108 +-#define UNICAM_IPIPE 0x10c +-#define UNICAM_IBSA0 0x110 +-#define UNICAM_IBEA0 0x114 +-#define UNICAM_IBLS 0x118 +-#define UNICAM_IBWP 0x11c +-#define UNICAM_IHWIN 0x120 +-#define UNICAM_IHSTA 0x124 +-#define UNICAM_IVWIN 0x128 +-#define UNICAM_IVSTA 0x12c +-#define UNICAM_ICC 0x130 +-#define UNICAM_ICS 0x134 +-#define UNICAM_IDC 0x138 +-#define UNICAM_IDPO 0x13c +-#define UNICAM_IDCA 0x140 +-#define UNICAM_IDCD 0x144 +-#define UNICAM_IDS 0x148 +-#define UNICAM_DCS 0x200 +-#define UNICAM_DBSA0 0x204 +-#define UNICAM_DBEA0 0x208 +-#define UNICAM_DBWP 0x20c +-#define UNICAM_DBCTL 0x300 +-#define UNICAM_IBSA1 0x304 +-#define UNICAM_IBEA1 0x308 +-#define UNICAM_IDI1 0x30c +-#define UNICAM_DBSA1 0x310 +-#define UNICAM_DBEA1 0x314 +-#define UNICAM_MISC 0x400 +- +-/* +- * The following bitmasks are from the kernel released by Broadcom +- * for Android - https://android.googlesource.com/kernel/bcm/ +- * The Rhea, Hawaii, and Java chips all contain the same VideoCore4 +- * Unicam block as BCM2835, as defined in eg +- * arch/arm/mach-rhea/include/mach/rdb_A0/brcm_rdb_cam.h and similar. +- * Values reworked to use the kernel BIT and GENMASK macros. +- * +- * Some of the bit mnenomics have been amended to match the datasheet. +- */ +-/* UNICAM_CTRL Register */ +-#define UNICAM_CPE BIT(0) +-#define UNICAM_MEM BIT(1) +-#define UNICAM_CPR BIT(2) +-#define UNICAM_CPM_MASK GENMASK(3, 3) +-#define UNICAM_CPM_CSI2 0 +-#define UNICAM_CPM_CCP2 1 +-#define UNICAM_SOE BIT(4) +-#define UNICAM_DCM_MASK GENMASK(5, 5) +-#define UNICAM_DCM_STROBE 0 +-#define UNICAM_DCM_DATA 1 +-#define UNICAM_SLS BIT(6) +-#define UNICAM_PFT_MASK GENMASK(11, 8) +-#define UNICAM_OET_MASK GENMASK(20, 12) +- +-/* UNICAM_STA Register */ +-#define UNICAM_SYN BIT(0) +-#define UNICAM_CS BIT(1) +-#define UNICAM_SBE BIT(2) +-#define UNICAM_PBE BIT(3) +-#define UNICAM_HOE BIT(4) +-#define UNICAM_PLE BIT(5) +-#define UNICAM_SSC BIT(6) +-#define UNICAM_CRCE BIT(7) +-#define UNICAM_OES BIT(8) +-#define UNICAM_IFO BIT(9) +-#define UNICAM_OFO BIT(10) +-#define UNICAM_BFO BIT(11) +-#define UNICAM_DL BIT(12) +-#define UNICAM_PS BIT(13) +-#define UNICAM_IS BIT(14) +-#define UNICAM_PI0 BIT(15) +-#define UNICAM_PI1 BIT(16) +-#define UNICAM_FSI_S BIT(17) +-#define UNICAM_FEI_S BIT(18) +-#define UNICAM_LCI_S BIT(19) +-#define UNICAM_BUF0_RDY BIT(20) +-#define UNICAM_BUF0_NO BIT(21) +-#define UNICAM_BUF1_RDY BIT(22) +-#define UNICAM_BUF1_NO BIT(23) +-#define UNICAM_DI BIT(24) +- +-#define UNICAM_STA_MASK_ALL \ +- (UNICAM_DL + \ +- UNICAM_SBE + \ +- UNICAM_PBE + \ +- UNICAM_HOE + \ +- UNICAM_PLE + \ +- UNICAM_SSC + \ +- UNICAM_CRCE + \ +- UNICAM_IFO + \ +- UNICAM_OFO + \ +- UNICAM_PS + \ +- UNICAM_PI0 + \ +- UNICAM_PI1) +- +-/* UNICAM_ANA Register */ +-#define UNICAM_APD BIT(0) +-#define UNICAM_BPD BIT(1) +-#define UNICAM_AR BIT(2) +-#define UNICAM_DDL BIT(3) +-#define UNICAM_CTATADJ_MASK GENMASK(7, 4) +-#define UNICAM_PTATADJ_MASK GENMASK(11, 8) +- +-/* UNICAM_PRI Register */ +-#define UNICAM_PE BIT(0) +-#define UNICAM_PT_MASK GENMASK(2, 1) +-#define UNICAM_NP_MASK GENMASK(7, 4) +-#define UNICAM_PP_MASK GENMASK(11, 8) +-#define UNICAM_BS_MASK GENMASK(15, 12) +-#define UNICAM_BL_MASK GENMASK(17, 16) +- +-/* UNICAM_CLK Register */ +-#define UNICAM_CLE BIT(0) +-#define UNICAM_CLPD BIT(1) +-#define UNICAM_CLLPE BIT(2) +-#define UNICAM_CLHSE BIT(3) +-#define UNICAM_CLTRE BIT(4) +-#define UNICAM_CLAC_MASK GENMASK(8, 5) +-#define UNICAM_CLSTE BIT(29) +- +-/* UNICAM_CLT Register */ +-#define UNICAM_CLT1_MASK GENMASK(7, 0) +-#define UNICAM_CLT2_MASK GENMASK(15, 8) +- +-/* UNICAM_DATn Registers */ +-#define UNICAM_DLE BIT(0) +-#define UNICAM_DLPD BIT(1) +-#define UNICAM_DLLPE BIT(2) +-#define UNICAM_DLHSE BIT(3) +-#define UNICAM_DLTRE BIT(4) +-#define UNICAM_DLSM BIT(5) +-#define UNICAM_DLFO BIT(28) +-#define UNICAM_DLSTE BIT(29) +- +-#define UNICAM_DAT_MASK_ALL (UNICAM_DLSTE + UNICAM_DLFO) +- +-/* UNICAM_DLT Register */ +-#define UNICAM_DLT1_MASK GENMASK(7, 0) +-#define UNICAM_DLT2_MASK GENMASK(15, 8) +-#define UNICAM_DLT3_MASK GENMASK(23, 16) +- +-/* UNICAM_ICTL Register */ +-#define UNICAM_FSIE BIT(0) +-#define UNICAM_FEIE BIT(1) +-#define UNICAM_IBOB BIT(2) +-#define UNICAM_FCM BIT(3) +-#define UNICAM_TFC BIT(4) +-#define UNICAM_LIP_MASK GENMASK(6, 5) +-#define UNICAM_LCIE_MASK GENMASK(28, 16) +- +-/* UNICAM_IDI0/1 Register */ +-#define UNICAM_ID0_MASK GENMASK(7, 0) +-#define UNICAM_ID1_MASK GENMASK(15, 8) +-#define UNICAM_ID2_MASK GENMASK(23, 16) +-#define UNICAM_ID3_MASK GENMASK(31, 24) +- +-/* UNICAM_ISTA Register */ +-#define UNICAM_FSI BIT(0) +-#define UNICAM_FEI BIT(1) +-#define UNICAM_LCI BIT(2) +- +-#define UNICAM_ISTA_MASK_ALL (UNICAM_FSI + UNICAM_FEI + UNICAM_LCI) +- +-/* UNICAM_IPIPE Register */ +-#define UNICAM_PUM_MASK GENMASK(2, 0) +- /* Unpacking modes */ +- #define UNICAM_PUM_NONE 0 +- #define UNICAM_PUM_UNPACK6 1 +- #define UNICAM_PUM_UNPACK7 2 +- #define UNICAM_PUM_UNPACK8 3 +- #define UNICAM_PUM_UNPACK10 4 +- #define UNICAM_PUM_UNPACK12 5 +- #define UNICAM_PUM_UNPACK14 6 +- #define UNICAM_PUM_UNPACK16 7 +-#define UNICAM_DDM_MASK GENMASK(6, 3) +-#define UNICAM_PPM_MASK GENMASK(9, 7) +- /* Packing modes */ +- #define UNICAM_PPM_NONE 0 +- #define UNICAM_PPM_PACK8 1 +- #define UNICAM_PPM_PACK10 2 +- #define UNICAM_PPM_PACK12 3 +- #define UNICAM_PPM_PACK14 4 +- #define UNICAM_PPM_PACK16 5 +-#define UNICAM_DEM_MASK GENMASK(11, 10) +-#define UNICAM_DEBL_MASK GENMASK(14, 12) +-#define UNICAM_ICM_MASK GENMASK(16, 15) +-#define UNICAM_IDM_MASK GENMASK(17, 17) +- +-/* UNICAM_ICC Register */ +-#define UNICAM_ICFL_MASK GENMASK(4, 0) +-#define UNICAM_ICFH_MASK GENMASK(9, 5) +-#define UNICAM_ICST_MASK GENMASK(12, 10) +-#define UNICAM_ICLT_MASK GENMASK(15, 13) +-#define UNICAM_ICLL_MASK GENMASK(31, 16) +- +-/* UNICAM_DCS Register */ +-#define UNICAM_DIE BIT(0) +-#define UNICAM_DIM BIT(1) +-#define UNICAM_DBOB BIT(3) +-#define UNICAM_FDE BIT(4) +-#define UNICAM_LDP BIT(5) +-#define UNICAM_EDL_MASK GENMASK(15, 8) +- +-/* UNICAM_DBCTL Register */ +-#define UNICAM_DBEN BIT(0) +-#define UNICAM_BUF0_IE BIT(1) +-#define UNICAM_BUF1_IE BIT(2) +- +-/* UNICAM_CMP[0,1] register */ +-#define UNICAM_PCE BIT(31) +-#define UNICAM_GI BIT(9) +-#define UNICAM_CPH BIT(8) +-#define UNICAM_PCVC_MASK GENMASK(7, 6) +-#define UNICAM_PCDT_MASK GENMASK(5, 0) +- +-/* UNICAM_MISC register */ +-#define UNICAM_FL0 BIT(6) +-#define UNICAM_FL1 BIT(9) +- +-#endif diff --git a/target/linux/bcm27xx/patches-5.10/950-0264-media-bcm2835-unicam-Driver-for-CCP2-CSI2-camera-int.patch b/target/linux/bcm27xx/patches-5.10/950-0264-media-bcm2835-unicam-Driver-for-CCP2-CSI2-camera-int.patch new file mode 100644 index 0000000000..67e4cdadae --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0264-media-bcm2835-unicam-Driver-for-CCP2-CSI2-camera-int.patch @@ -0,0 +1,3150 @@ +From ad386ab52fe80a35042a1a0d0eef0c87d2419dfc Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Mon, 4 May 2020 12:25:41 +0300 +Subject: [PATCH] media: bcm2835-unicam: Driver for CCP2/CSI2 camera + interface + +Add a driver for the Unicam camera receiver block on BCM283x processors. +Compared to the bcm2835-camera driver present in staging, this driver +handles the Unicam block only (CSI-2 receiver), and doesn't depend on +the VC4 firmware running on the VPU. + +The commit is made up of a series of changes cherry-picked from the +rpi-5.4.y branch of https://github.com/raspberrypi/linux/ with +additional enhancements, forward-ported to the mainline kernel. + +Signed-off-by: Dave Stevenson +Signed-off-by: Naushir Patuck +Signed-off-by: Laurent Pinchart +Reported-by: kbuild test robot +--- + MAINTAINERS | 2 +- + drivers/media/platform/bcm2835/Kconfig | 15 + + drivers/media/platform/bcm2835/Makefile | 3 + + .../media/platform/bcm2835/bcm2835-unicam.c | 2825 +++++++++++++++++ + .../media/platform/bcm2835/vc4-regs-unicam.h | 253 ++ + 5 files changed, 3097 insertions(+), 1 deletion(-) + create mode 100644 drivers/media/platform/bcm2835/Kconfig + create mode 100644 drivers/media/platform/bcm2835/Makefile + create mode 100644 drivers/media/platform/bcm2835/bcm2835-unicam.c + create mode 100644 drivers/media/platform/bcm2835/vc4-regs-unicam.h + +--- a/MAINTAINERS ++++ b/MAINTAINERS +@@ -3429,7 +3429,7 @@ M: Raspberry Pi Kernel Maintenance +--- /dev/null ++++ b/drivers/media/platform/bcm2835/Kconfig +@@ -0,0 +1,15 @@ ++# Broadcom VideoCore4 V4L2 camera support ++ ++config VIDEO_BCM2835_UNICAM ++ tristate "Broadcom BCM2835 Unicam video capture driver" ++ depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && MEDIA_CONTROLLER ++ depends on ARCH_BCM2835 || COMPILE_TEST ++ select VIDEOBUF2_DMA_CONTIG ++ select V4L2_FWNODE ++ help ++ Say Y here to enable support for the BCM2835 CSI-2 receiver. This is a ++ V4L2 driver that controls the CSI-2 receiver directly, independently ++ from the VC4 firmware. ++ ++ To compile this driver as a module, choose M here. The module will be ++ called bcm2835-unicam. +--- /dev/null ++++ b/drivers/media/platform/bcm2835/Makefile +@@ -0,0 +1,3 @@ ++# Makefile for BCM2835 Unicam driver ++ ++obj-$(CONFIG_VIDEO_BCM2835_UNICAM) += bcm2835-unicam.o +--- /dev/null ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -0,0 +1,2825 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++/* ++ * BCM2835 Unicam Capture Driver ++ * ++ * Copyright (C) 2017-2020 - Raspberry Pi (Trading) Ltd. ++ * ++ * Dave Stevenson ++ * ++ * Based on TI am437x driver by ++ * Benoit Parrot ++ * Lad, Prabhakar ++ * ++ * and TI CAL camera interface driver by ++ * Benoit Parrot ++ * ++ * ++ * There are two camera drivers in the kernel for BCM283x - this one ++ * and bcm2835-camera (currently in staging). ++ * ++ * This driver directly controls the Unicam peripheral - there is no ++ * involvement with the VideoCore firmware. Unicam receives CSI-2 or ++ * CCP2 data and writes it into SDRAM. ++ * The only potential processing options are to repack Bayer data into an ++ * alternate format, and applying windowing. ++ * The repacking does not shift the data, so can repack V4L2_PIX_FMT_Sxxxx10P ++ * to V4L2_PIX_FMT_Sxxxx10, or V4L2_PIX_FMT_Sxxxx12P to V4L2_PIX_FMT_Sxxxx12, ++ * but not generically up to V4L2_PIX_FMT_Sxxxx16. The driver will add both ++ * formats where the relevant formats are defined, and will automatically ++ * configure the repacking as required. ++ * Support for windowing may be added later. ++ * ++ * It should be possible to connect this driver to any sensor with a ++ * suitable output interface and V4L2 subdevice driver. ++ * ++ * bcm2835-camera uses the VideoCore firmware to control the sensor, ++ * Unicam, ISP, and all tuner control loops. Fully processed frames are ++ * delivered to the driver by the firmware. It only has sensor drivers ++ * for Omnivision OV5647, and Sony IMX219 sensors. ++ * ++ * The two drivers are mutually exclusive for the same Unicam instance. ++ * The VideoCore firmware checks the device tree configuration during boot. ++ * If it finds device tree nodes called csi0 or csi1 it will block the ++ * firmware from accessing the peripheral, and bcm2835-camera will ++ * not be able to stream data. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include "vc4-regs-unicam.h" ++ ++#define UNICAM_MODULE_NAME "unicam" ++#define UNICAM_VERSION "0.1.0" ++ ++static int debug; ++module_param(debug, int, 0644); ++MODULE_PARM_DESC(debug, "Debug level 0-3"); ++ ++#define unicam_dbg(level, dev, fmt, arg...) \ ++ v4l2_dbg(level, debug, &(dev)->v4l2_dev, fmt, ##arg) ++#define unicam_info(dev, fmt, arg...) \ ++ v4l2_info(&(dev)->v4l2_dev, fmt, ##arg) ++#define unicam_err(dev, fmt, arg...) \ ++ v4l2_err(&(dev)->v4l2_dev, fmt, ##arg) ++ ++/* ++ * To protect against a dodgy sensor driver never returning an error from ++ * enum_mbus_code, set a maximum index value to be used. ++ */ ++#define MAX_ENUM_MBUS_CODE 128 ++ ++/* ++ * Stride is a 16 bit register, but also has to be a multiple of 32. ++ */ ++#define BPL_ALIGNMENT 32 ++#define MAX_BYTESPERLINE ((1 << 16) - BPL_ALIGNMENT) ++/* ++ * Max width is therefore determined by the max stride divided by ++ * the number of bits per pixel. Take 32bpp as a ++ * worst case. ++ * No imposed limit on the height, so adopt a square image for want ++ * of anything better. ++ */ ++#define MAX_WIDTH (MAX_BYTESPERLINE / 4) ++#define MAX_HEIGHT MAX_WIDTH ++/* Define a nominal minimum image size */ ++#define MIN_WIDTH 16 ++#define MIN_HEIGHT 16 ++/* Default size of the embedded buffer */ ++#define UNICAM_EMBEDDED_SIZE 8192 ++ ++/* ++ * Size of the dummy buffer. Can be any size really, but the DMA ++ * allocation works in units of page sizes. ++ */ ++#define DUMMY_BUF_SIZE (PAGE_SIZE) ++ ++enum pad_types { ++ IMAGE_PAD, ++ METADATA_PAD, ++ MAX_NODES ++}; ++ ++/* ++ * struct unicam_fmt - Unicam media bus format information ++ * @pixelformat: V4L2 pixel format FCC identifier. 0 if n/a. ++ * @repacked_fourcc: V4L2 pixel format FCC identifier if the data is expanded ++ * out to 16bpp. 0 if n/a. ++ * @code: V4L2 media bus format code. ++ * @depth: Bits per pixel as delivered from the source. ++ * @csi_dt: CSI data type. ++ * @check_variants: Flag to denote that there are multiple mediabus formats ++ * still in the list that could match this V4L2 format. ++ */ ++struct unicam_fmt { ++ u32 fourcc; ++ u32 repacked_fourcc; ++ u32 code; ++ u8 depth; ++ u8 csi_dt; ++ u8 check_variants; ++}; ++ ++static const struct unicam_fmt formats[] = { ++ /* YUV Formats */ ++ { ++ .fourcc = V4L2_PIX_FMT_YUYV, ++ .code = MEDIA_BUS_FMT_YUYV8_2X8, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ .check_variants = 1, ++ }, { ++ .fourcc = V4L2_PIX_FMT_UYVY, ++ .code = MEDIA_BUS_FMT_UYVY8_2X8, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ .check_variants = 1, ++ }, { ++ .fourcc = V4L2_PIX_FMT_YVYU, ++ .code = MEDIA_BUS_FMT_YVYU8_2X8, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ .check_variants = 1, ++ }, { ++ .fourcc = V4L2_PIX_FMT_VYUY, ++ .code = MEDIA_BUS_FMT_VYUY8_2X8, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ .check_variants = 1, ++ }, { ++ .fourcc = V4L2_PIX_FMT_YUYV, ++ .code = MEDIA_BUS_FMT_YUYV8_1X16, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ }, { ++ .fourcc = V4L2_PIX_FMT_UYVY, ++ .code = MEDIA_BUS_FMT_UYVY8_1X16, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ }, { ++ .fourcc = V4L2_PIX_FMT_YVYU, ++ .code = MEDIA_BUS_FMT_YVYU8_1X16, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ }, { ++ .fourcc = V4L2_PIX_FMT_VYUY, ++ .code = MEDIA_BUS_FMT_VYUY8_1X16, ++ .depth = 16, ++ .csi_dt = 0x1e, ++ }, { ++ /* RGB Formats */ ++ .fourcc = V4L2_PIX_FMT_RGB565, /* gggbbbbb rrrrrggg */ ++ .code = MEDIA_BUS_FMT_RGB565_2X8_LE, ++ .depth = 16, ++ .csi_dt = 0x22, ++ }, { ++ .fourcc = V4L2_PIX_FMT_RGB565X, /* rrrrrggg gggbbbbb */ ++ .code = MEDIA_BUS_FMT_RGB565_2X8_BE, ++ .depth = 16, ++ .csi_dt = 0x22 ++ }, { ++ .fourcc = V4L2_PIX_FMT_RGB555, /* gggbbbbb arrrrrgg */ ++ .code = MEDIA_BUS_FMT_RGB555_2X8_PADHI_LE, ++ .depth = 16, ++ .csi_dt = 0x21, ++ }, { ++ .fourcc = V4L2_PIX_FMT_RGB555X, /* arrrrrgg gggbbbbb */ ++ .code = MEDIA_BUS_FMT_RGB555_2X8_PADHI_BE, ++ .depth = 16, ++ .csi_dt = 0x21, ++ }, { ++ .fourcc = V4L2_PIX_FMT_RGB24, /* rgb */ ++ .code = MEDIA_BUS_FMT_RGB888_1X24, ++ .depth = 24, ++ .csi_dt = 0x24, ++ }, { ++ .fourcc = V4L2_PIX_FMT_BGR24, /* bgr */ ++ .code = MEDIA_BUS_FMT_BGR888_1X24, ++ .depth = 24, ++ .csi_dt = 0x24, ++ }, { ++ .fourcc = V4L2_PIX_FMT_RGB32, /* argb */ ++ .code = MEDIA_BUS_FMT_ARGB8888_1X32, ++ .depth = 32, ++ .csi_dt = 0x0, ++ }, { ++ /* Bayer Formats */ ++ .fourcc = V4L2_PIX_FMT_SBGGR8, ++ .code = MEDIA_BUS_FMT_SBGGR8_1X8, ++ .depth = 8, ++ .csi_dt = 0x2a, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGBRG8, ++ .code = MEDIA_BUS_FMT_SGBRG8_1X8, ++ .depth = 8, ++ .csi_dt = 0x2a, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGRBG8, ++ .code = MEDIA_BUS_FMT_SGRBG8_1X8, ++ .depth = 8, ++ .csi_dt = 0x2a, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SRGGB8, ++ .code = MEDIA_BUS_FMT_SRGGB8_1X8, ++ .depth = 8, ++ .csi_dt = 0x2a, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SBGGR10P, ++ .repacked_fourcc = V4L2_PIX_FMT_SBGGR10, ++ .code = MEDIA_BUS_FMT_SBGGR10_1X10, ++ .depth = 10, ++ .csi_dt = 0x2b, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGBRG10P, ++ .repacked_fourcc = V4L2_PIX_FMT_SGBRG10, ++ .code = MEDIA_BUS_FMT_SGBRG10_1X10, ++ .depth = 10, ++ .csi_dt = 0x2b, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGRBG10P, ++ .repacked_fourcc = V4L2_PIX_FMT_SGRBG10, ++ .code = MEDIA_BUS_FMT_SGRBG10_1X10, ++ .depth = 10, ++ .csi_dt = 0x2b, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SRGGB10P, ++ .repacked_fourcc = V4L2_PIX_FMT_SRGGB10, ++ .code = MEDIA_BUS_FMT_SRGGB10_1X10, ++ .depth = 10, ++ .csi_dt = 0x2b, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SBGGR12P, ++ .repacked_fourcc = V4L2_PIX_FMT_SBGGR12, ++ .code = MEDIA_BUS_FMT_SBGGR12_1X12, ++ .depth = 12, ++ .csi_dt = 0x2c, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGBRG12P, ++ .repacked_fourcc = V4L2_PIX_FMT_SGBRG12, ++ .code = MEDIA_BUS_FMT_SGBRG12_1X12, ++ .depth = 12, ++ .csi_dt = 0x2c, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGRBG12P, ++ .repacked_fourcc = V4L2_PIX_FMT_SGRBG12, ++ .code = MEDIA_BUS_FMT_SGRBG12_1X12, ++ .depth = 12, ++ .csi_dt = 0x2c, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SRGGB12P, ++ .repacked_fourcc = V4L2_PIX_FMT_SRGGB12, ++ .code = MEDIA_BUS_FMT_SRGGB12_1X12, ++ .depth = 12, ++ .csi_dt = 0x2c, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SBGGR14P, ++ .code = MEDIA_BUS_FMT_SBGGR14_1X14, ++ .depth = 14, ++ .csi_dt = 0x2d, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGBRG14P, ++ .code = MEDIA_BUS_FMT_SGBRG14_1X14, ++ .depth = 14, ++ .csi_dt = 0x2d, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SGRBG14P, ++ .code = MEDIA_BUS_FMT_SGRBG14_1X14, ++ .depth = 14, ++ .csi_dt = 0x2d, ++ }, { ++ .fourcc = V4L2_PIX_FMT_SRGGB14P, ++ .code = MEDIA_BUS_FMT_SRGGB14_1X14, ++ .depth = 14, ++ .csi_dt = 0x2d, ++ }, { ++ /* ++ * 16 bit Bayer formats could be supported, but there is no CSI2 ++ * data_type defined for raw 16, and no sensors that produce it at ++ * present. ++ */ ++ ++ /* Greyscale formats */ ++ .fourcc = V4L2_PIX_FMT_GREY, ++ .code = MEDIA_BUS_FMT_Y8_1X8, ++ .depth = 8, ++ .csi_dt = 0x2a, ++ }, { ++ .fourcc = V4L2_PIX_FMT_Y10P, ++ .repacked_fourcc = V4L2_PIX_FMT_Y10, ++ .code = MEDIA_BUS_FMT_Y10_1X10, ++ .depth = 10, ++ .csi_dt = 0x2b, ++ }, { ++ /* NB There is no packed V4L2 fourcc for this format. */ ++ .repacked_fourcc = V4L2_PIX_FMT_Y12, ++ .code = MEDIA_BUS_FMT_Y12_1X12, ++ .depth = 12, ++ .csi_dt = 0x2c, ++ }, ++ /* Embedded data format */ ++ { ++ .fourcc = V4L2_META_FMT_SENSOR_DATA, ++ .code = MEDIA_BUS_FMT_SENSOR_DATA, ++ .depth = 8, ++ } ++}; ++ ++struct unicam_buffer { ++ struct vb2_v4l2_buffer vb; ++ struct list_head list; ++}; ++ ++static inline struct unicam_buffer *to_unicam_buffer(struct vb2_buffer *vb) ++{ ++ return container_of(vb, struct unicam_buffer, vb.vb2_buf); ++} ++ ++struct unicam_node { ++ bool registered; ++ int open; ++ bool streaming; ++ unsigned int pad_id; ++ /* Pointer pointing to current v4l2_buffer */ ++ struct unicam_buffer *cur_frm; ++ /* Pointer pointing to next v4l2_buffer */ ++ struct unicam_buffer *next_frm; ++ /* video capture */ ++ const struct unicam_fmt *fmt; ++ /* Used to store current pixel format */ ++ struct v4l2_format v_fmt; ++ /* Used to store current mbus frame format */ ++ struct v4l2_mbus_framefmt m_fmt; ++ /* Buffer queue used in video-buf */ ++ struct vb2_queue buffer_queue; ++ /* Queue of filled frames */ ++ struct list_head dma_queue; ++ /* IRQ lock for DMA queue */ ++ spinlock_t dma_queue_lock; ++ /* lock used to access this structure */ ++ struct mutex lock; ++ /* Identifies video device for this channel */ ++ struct video_device video_dev; ++ /* Pointer to the parent handle */ ++ struct unicam_device *dev; ++ struct media_pad pad; ++ unsigned int embedded_lines; ++ /* ++ * Dummy buffer intended to be used by unicam ++ * if we have no other queued buffers to swap to. ++ */ ++ void *dummy_buf_cpu_addr; ++ dma_addr_t dummy_buf_dma_addr; ++}; ++ ++struct unicam_device { ++ struct kref kref; ++ ++ /* V4l2 specific parameters */ ++ struct v4l2_async_subdev asd; ++ ++ /* peripheral base address */ ++ void __iomem *base; ++ /* clock gating base address */ ++ void __iomem *clk_gate_base; ++ /* clock handle */ ++ struct clk *clock; ++ /* V4l2 device */ ++ struct v4l2_device v4l2_dev; ++ struct media_device mdev; ++ ++ /* parent device */ ++ struct platform_device *pdev; ++ /* subdevice async Notifier */ ++ struct v4l2_async_notifier notifier; ++ unsigned int sequence; ++ ++ /* ptr to sub device */ ++ struct v4l2_subdev *sensor; ++ /* Pad config for the sensor */ ++ struct v4l2_subdev_pad_config *sensor_config; ++ ++ enum v4l2_mbus_type bus_type; ++ /* ++ * Stores bus.mipi_csi2.flags for CSI2 sensors, or ++ * bus.mipi_csi1.strobe for CCP2. ++ */ ++ unsigned int bus_flags; ++ unsigned int max_data_lanes; ++ unsigned int active_data_lanes; ++ bool sensor_embedded_data; ++ ++ struct unicam_node node[MAX_NODES]; ++ struct v4l2_ctrl_handler ctrl_handler; ++}; ++ ++static inline struct unicam_device * ++to_unicam_device(struct v4l2_device *v4l2_dev) ++{ ++ return container_of(v4l2_dev, struct unicam_device, v4l2_dev); ++} ++ ++/* Hardware access */ ++static inline void clk_write(struct unicam_device *dev, u32 val) ++{ ++ writel(val | 0x5a000000, dev->clk_gate_base); ++} ++ ++static inline u32 reg_read(struct unicam_device *dev, u32 offset) ++{ ++ return readl(dev->base + offset); ++} ++ ++static inline void reg_write(struct unicam_device *dev, u32 offset, u32 val) ++{ ++ writel(val, dev->base + offset); ++} ++ ++static inline int get_field(u32 value, u32 mask) ++{ ++ return (value & mask) >> __ffs(mask); ++} ++ ++static inline void set_field(u32 *valp, u32 field, u32 mask) ++{ ++ u32 val = *valp; ++ ++ val &= ~mask; ++ val |= (field << __ffs(mask)) & mask; ++ *valp = val; ++} ++ ++static inline u32 reg_read_field(struct unicam_device *dev, u32 offset, ++ u32 mask) ++{ ++ return get_field(reg_read(dev, offset), mask); ++} ++ ++static inline void reg_write_field(struct unicam_device *dev, u32 offset, ++ u32 field, u32 mask) ++{ ++ u32 val = reg_read(dev, offset); ++ ++ set_field(&val, field, mask); ++ reg_write(dev, offset, val); ++} ++ ++/* Power management functions */ ++static inline int unicam_runtime_get(struct unicam_device *dev) ++{ ++ return pm_runtime_get_sync(&dev->pdev->dev); ++} ++ ++static inline void unicam_runtime_put(struct unicam_device *dev) ++{ ++ pm_runtime_put_sync(&dev->pdev->dev); ++} ++ ++/* Format setup functions */ ++static const struct unicam_fmt *find_format_by_code(u32 code) ++{ ++ unsigned int i; ++ ++ for (i = 0; i < ARRAY_SIZE(formats); i++) { ++ if (formats[i].code == code) ++ return &formats[i]; ++ } ++ ++ return NULL; ++} ++ ++static int check_mbus_format(struct unicam_device *dev, ++ const struct unicam_fmt *format) ++{ ++ unsigned int i; ++ int ret = 0; ++ ++ for (i = 0; !ret && i < MAX_ENUM_MBUS_CODE; i++) { ++ struct v4l2_subdev_mbus_code_enum mbus_code = { ++ .index = i, ++ .pad = IMAGE_PAD, ++ .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ }; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, ++ NULL, &mbus_code); ++ ++ if (!ret && mbus_code.code == format->code) ++ return 1; ++ } ++ ++ return 0; ++} ++ ++static const struct unicam_fmt *find_format_by_pix(struct unicam_device *dev, ++ u32 pixelformat) ++{ ++ unsigned int i; ++ ++ for (i = 0; i < ARRAY_SIZE(formats); i++) { ++ if (formats[i].fourcc == pixelformat || ++ formats[i].repacked_fourcc == pixelformat) { ++ if (formats[i].check_variants && ++ !check_mbus_format(dev, &formats[i])) ++ continue; ++ return &formats[i]; ++ } ++ } ++ ++ return NULL; ++} ++ ++static inline unsigned int bytes_per_line(u32 width, ++ const struct unicam_fmt *fmt, ++ u32 v4l2_fourcc) ++{ ++ if (v4l2_fourcc == fmt->repacked_fourcc) ++ /* Repacking always goes to 16bpp */ ++ return ALIGN(width << 1, BPL_ALIGNMENT); ++ else ++ return ALIGN((width * fmt->depth) >> 3, BPL_ALIGNMENT); ++} ++ ++static int __subdev_get_format(struct unicam_device *dev, ++ struct v4l2_mbus_framefmt *fmt, int pad_id) ++{ ++ struct v4l2_subdev_format sd_fmt = { ++ .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ .pad = pad_id ++ }; ++ int ret; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, get_fmt, dev->sensor_config, ++ &sd_fmt); ++ if (ret < 0) ++ return ret; ++ ++ *fmt = sd_fmt.format; ++ ++ unicam_dbg(1, dev, "%s %dx%d code:%04x\n", __func__, ++ fmt->width, fmt->height, fmt->code); ++ ++ return 0; ++} ++ ++static int __subdev_set_format(struct unicam_device *dev, ++ struct v4l2_mbus_framefmt *fmt, int pad_id) ++{ ++ struct v4l2_subdev_format sd_fmt = { ++ .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ .pad = pad_id ++ }; ++ int ret; ++ ++ sd_fmt.format = *fmt; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, set_fmt, dev->sensor_config, ++ &sd_fmt); ++ if (ret < 0) ++ return ret; ++ ++ *fmt = sd_fmt.format; ++ ++ if (pad_id == IMAGE_PAD) ++ unicam_dbg(1, dev, "%s %dx%d code:%04x\n", __func__, fmt->width, ++ fmt->height, fmt->code); ++ else ++ unicam_dbg(1, dev, "%s Embedded data code:%04x\n", __func__, ++ sd_fmt.format.code); ++ ++ return 0; ++} ++ ++static int unicam_calc_format_size_bpl(struct unicam_device *dev, ++ const struct unicam_fmt *fmt, ++ struct v4l2_format *f) ++{ ++ unsigned int min_bytesperline; ++ ++ v4l_bound_align_image(&f->fmt.pix.width, MIN_WIDTH, MAX_WIDTH, 2, ++ &f->fmt.pix.height, MIN_HEIGHT, MAX_HEIGHT, 0, ++ 0); ++ ++ min_bytesperline = bytes_per_line(f->fmt.pix.width, fmt, ++ f->fmt.pix.pixelformat); ++ ++ if (f->fmt.pix.bytesperline > min_bytesperline && ++ f->fmt.pix.bytesperline <= MAX_BYTESPERLINE) ++ f->fmt.pix.bytesperline = ALIGN(f->fmt.pix.bytesperline, ++ BPL_ALIGNMENT); ++ else ++ f->fmt.pix.bytesperline = min_bytesperline; ++ ++ f->fmt.pix.sizeimage = f->fmt.pix.height * f->fmt.pix.bytesperline; ++ ++ unicam_dbg(3, dev, "%s: fourcc: %08X size: %dx%d bpl:%d img_size:%d\n", ++ __func__, ++ f->fmt.pix.pixelformat, ++ f->fmt.pix.width, f->fmt.pix.height, ++ f->fmt.pix.bytesperline, f->fmt.pix.sizeimage); ++ ++ return 0; ++} ++ ++static int unicam_reset_format(struct unicam_node *node) ++{ ++ struct unicam_device *dev = node->dev; ++ struct v4l2_mbus_framefmt mbus_fmt; ++ int ret; ++ ++ if (dev->sensor_embedded_data || node->pad_id != METADATA_PAD) { ++ ret = __subdev_get_format(dev, &mbus_fmt, node->pad_id); ++ if (ret) { ++ unicam_err(dev, "Failed to get_format - ret %d\n", ret); ++ return ret; ++ } ++ ++ if (mbus_fmt.code != node->fmt->code) { ++ unicam_err(dev, "code mismatch - fmt->code %08x, mbus_fmt.code %08x\n", ++ node->fmt->code, mbus_fmt.code); ++ return ret; ++ } ++ } ++ ++ if (node->pad_id == IMAGE_PAD) { ++ v4l2_fill_pix_format(&node->v_fmt.fmt.pix, &mbus_fmt); ++ node->v_fmt.type = V4L2_BUF_TYPE_VIDEO_CAPTURE; ++ unicam_calc_format_size_bpl(dev, node->fmt, &node->v_fmt); ++ } else { ++ node->v_fmt.type = V4L2_BUF_TYPE_META_CAPTURE; ++ node->v_fmt.fmt.meta.dataformat = V4L2_META_FMT_SENSOR_DATA; ++ if (dev->sensor_embedded_data) { ++ node->v_fmt.fmt.meta.buffersize = ++ mbus_fmt.width * mbus_fmt.height; ++ node->embedded_lines = mbus_fmt.height; ++ } else { ++ node->v_fmt.fmt.meta.buffersize = UNICAM_EMBEDDED_SIZE; ++ node->embedded_lines = 1; ++ } ++ } ++ ++ node->m_fmt = mbus_fmt; ++ return 0; ++} ++ ++static void unicam_wr_dma_addr(struct unicam_device *dev, dma_addr_t dmaaddr, ++ unsigned int buffer_size, int pad_id) ++{ ++ dma_addr_t endaddr = dmaaddr + buffer_size; ++ ++ /* ++ * dmaaddr and endaddr should be a 32-bit address with the top two bits ++ * set to 0x3 to signify uncached access through the Videocore memory ++ * controller. ++ */ ++ WARN_ON((dmaaddr >> 30) != 0x3 || (endaddr >> 30) != 0x3); ++ ++ if (pad_id == IMAGE_PAD) { ++ reg_write(dev, UNICAM_IBSA0, dmaaddr); ++ reg_write(dev, UNICAM_IBEA0, endaddr); ++ } else { ++ reg_write(dev, UNICAM_DBSA0, dmaaddr); ++ reg_write(dev, UNICAM_DBEA0, endaddr); ++ } ++} ++ ++static inline unsigned int unicam_get_lines_done(struct unicam_device *dev) ++{ ++ dma_addr_t start_addr, cur_addr; ++ unsigned int stride = dev->node[IMAGE_PAD].v_fmt.fmt.pix.bytesperline; ++ struct unicam_buffer *frm = dev->node[IMAGE_PAD].cur_frm; ++ ++ if (!frm) ++ return 0; ++ ++ start_addr = vb2_dma_contig_plane_dma_addr(&frm->vb.vb2_buf, 0); ++ cur_addr = reg_read(dev, UNICAM_IBWP); ++ return (unsigned int)(cur_addr - start_addr) / stride; ++} ++ ++static inline void unicam_schedule_next_buffer(struct unicam_node *node) ++{ ++ struct unicam_device *dev = node->dev; ++ struct unicam_buffer *buf; ++ unsigned int size; ++ dma_addr_t addr; ++ ++ buf = list_first_entry(&node->dma_queue, struct unicam_buffer, list); ++ node->next_frm = buf; ++ list_del(&buf->list); ++ ++ addr = vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0); ++ size = (node->pad_id == IMAGE_PAD) ? ++ node->v_fmt.fmt.pix.sizeimage : ++ node->v_fmt.fmt.meta.buffersize; ++ ++ unicam_wr_dma_addr(dev, addr, size, node->pad_id); ++} ++ ++static inline void unicam_schedule_dummy_buffer(struct unicam_node *node) ++{ ++ struct unicam_device *dev = node->dev; ++ ++ unicam_dbg(3, dev, "Scheduling dummy buffer for node %d\n", ++ node->pad_id); ++ ++ unicam_wr_dma_addr(dev, node->dummy_buf_dma_addr, DUMMY_BUF_SIZE, ++ node->pad_id); ++ node->next_frm = NULL; ++} ++ ++static inline void unicam_process_buffer_complete(struct unicam_node *node, ++ unsigned int sequence) ++{ ++ node->cur_frm->vb.field = node->m_fmt.field; ++ node->cur_frm->vb.sequence = sequence; ++ ++ vb2_buffer_done(&node->cur_frm->vb.vb2_buf, VB2_BUF_STATE_DONE); ++} ++ ++static bool unicam_all_nodes_streaming(struct unicam_device *dev) ++{ ++ bool ret; ++ ++ ret = dev->node[IMAGE_PAD].open && dev->node[IMAGE_PAD].streaming; ++ ret &= !dev->node[METADATA_PAD].open || ++ dev->node[METADATA_PAD].streaming; ++ return ret; ++} ++ ++static bool unicam_all_nodes_disabled(struct unicam_device *dev) ++{ ++ return !dev->node[IMAGE_PAD].streaming && ++ !dev->node[METADATA_PAD].streaming; ++} ++ ++static void unicam_queue_event_sof(struct unicam_device *unicam) ++{ ++ struct v4l2_event event = { ++ .type = V4L2_EVENT_FRAME_SYNC, ++ .u.frame_sync.frame_sequence = unicam->sequence, ++ }; ++ ++ v4l2_event_queue(&unicam->node[IMAGE_PAD].video_dev, &event); ++} ++ ++/* ++ * unicam_isr : ISR handler for unicam capture ++ * @irq: irq number ++ * @dev_id: dev_id ptr ++ * ++ * It changes status of the captured buffer, takes next buffer from the queue ++ * and sets its address in unicam registers ++ */ ++static irqreturn_t unicam_isr(int irq, void *dev) ++{ ++ struct unicam_device *unicam = dev; ++ unsigned int lines_done = unicam_get_lines_done(dev); ++ unsigned int sequence = unicam->sequence; ++ unsigned int i; ++ u32 ista, sta; ++ u64 ts; ++ ++ /* ++ * Don't service interrupts if not streaming. ++ * Avoids issues if the VPU should enable the ++ * peripheral without the kernel knowing (that ++ * shouldn't happen, but causes issues if it does). ++ */ ++ if (unicam_all_nodes_disabled(unicam)) ++ return IRQ_NONE; ++ ++ sta = reg_read(unicam, UNICAM_STA); ++ /* Write value back to clear the interrupts */ ++ reg_write(unicam, UNICAM_STA, sta); ++ ++ ista = reg_read(unicam, UNICAM_ISTA); ++ /* Write value back to clear the interrupts */ ++ reg_write(unicam, UNICAM_ISTA, ista); ++ ++ unicam_dbg(3, unicam, "ISR: ISTA: 0x%X, STA: 0x%X, sequence %d, lines done %d", ++ ista, sta, sequence, lines_done); ++ ++ if (!(sta & (UNICAM_IS | UNICAM_PI0))) ++ return IRQ_HANDLED; ++ ++ /* ++ * We must run the frame end handler first. If we have a valid next_frm ++ * and we get a simultaneout FE + FS interrupt, running the FS handler ++ * first would null out the next_frm ptr and we would have lost the ++ * buffer forever. ++ */ ++ if (ista & UNICAM_FEI || sta & UNICAM_PI0) { ++ /* ++ * Ensure we have swapped buffers already as we can't ++ * stop the peripheral. If no buffer is available, use a ++ * dummy buffer to dump out frames until we get a new buffer ++ * to use. ++ */ ++ for (i = 0; i < ARRAY_SIZE(unicam->node); i++) { ++ if (!unicam->node[i].streaming) ++ continue; ++ ++ if (unicam->node[i].cur_frm) ++ unicam_process_buffer_complete(&unicam->node[i], ++ sequence); ++ unicam->node[i].cur_frm = unicam->node[i].next_frm; ++ } ++ unicam->sequence++; ++ } ++ ++ if (ista & UNICAM_FSI) { ++ /* ++ * Timestamp is to be when the first data byte was captured, ++ * aka frame start. ++ */ ++ ts = ktime_get_ns(); ++ for (i = 0; i < ARRAY_SIZE(unicam->node); i++) { ++ if (!unicam->node[i].streaming) ++ continue; ++ ++ if (unicam->node[i].cur_frm) ++ unicam->node[i].cur_frm->vb.vb2_buf.timestamp = ++ ts; ++ /* ++ * Set the next frame output to go to a dummy frame ++ * if we have not managed to obtain another frame ++ * from the queue. ++ */ ++ unicam_schedule_dummy_buffer(&unicam->node[i]); ++ } ++ ++ unicam_queue_event_sof(unicam); ++ } ++ ++ /* ++ * Cannot swap buffer at frame end, there may be a race condition ++ * where the HW does not actually swap it if the new frame has ++ * already started. ++ */ ++ if (ista & (UNICAM_FSI | UNICAM_LCI) && !(ista & UNICAM_FEI)) { ++ for (i = 0; i < ARRAY_SIZE(unicam->node); i++) { ++ if (!unicam->node[i].streaming) ++ continue; ++ ++ spin_lock(&unicam->node[i].dma_queue_lock); ++ if (!list_empty(&unicam->node[i].dma_queue) && ++ !unicam->node[i].next_frm) ++ unicam_schedule_next_buffer(&unicam->node[i]); ++ spin_unlock(&unicam->node[i].dma_queue_lock); ++ } ++ } ++ ++ if (reg_read(unicam, UNICAM_ICTL) & UNICAM_FCM) { ++ /* Switch out of trigger mode if selected */ ++ reg_write_field(unicam, UNICAM_ICTL, 1, UNICAM_TFC); ++ reg_write_field(unicam, UNICAM_ICTL, 0, UNICAM_FCM); ++ } ++ return IRQ_HANDLED; ++} ++ ++static int unicam_querycap(struct file *file, void *priv, ++ struct v4l2_capability *cap) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ ++ strlcpy(cap->driver, UNICAM_MODULE_NAME, sizeof(cap->driver)); ++ strlcpy(cap->card, UNICAM_MODULE_NAME, sizeof(cap->card)); ++ ++ snprintf(cap->bus_info, sizeof(cap->bus_info), ++ "platform:%s", dev_name(&dev->pdev->dev)); ++ ++ cap->capabilities |= V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_META_CAPTURE; ++ ++ return 0; ++} ++ ++static int unicam_enum_fmt_vid_cap(struct file *file, void *priv, ++ struct v4l2_fmtdesc *f) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ unsigned int index = 0; ++ unsigned int i; ++ int ret = 0; ++ ++ if (node->pad_id != IMAGE_PAD) ++ return -EINVAL; ++ ++ for (i = 0; !ret && i < MAX_ENUM_MBUS_CODE; i++) { ++ struct v4l2_subdev_mbus_code_enum mbus_code = { ++ .index = i, ++ .pad = IMAGE_PAD, ++ .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ }; ++ const struct unicam_fmt *fmt; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, ++ NULL, &mbus_code); ++ if (ret < 0) { ++ unicam_dbg(2, dev, ++ "subdev->enum_mbus_code idx %d returned %d - index invalid\n", ++ i, ret); ++ return -EINVAL; ++ } ++ ++ fmt = find_format_by_code(mbus_code.code); ++ if (fmt) { ++ if (fmt->fourcc) { ++ if (index == f->index) { ++ f->pixelformat = fmt->fourcc; ++ break; ++ } ++ index++; ++ } ++ if (fmt->repacked_fourcc) { ++ if (index == f->index) { ++ f->pixelformat = fmt->repacked_fourcc; ++ break; ++ } ++ index++; ++ } ++ } ++ } ++ ++ return 0; ++} ++ ++static int unicam_g_fmt_vid_cap(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct v4l2_mbus_framefmt mbus_fmt = {0}; ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ const struct unicam_fmt *fmt = NULL; ++ int ret; ++ ++ if (node->pad_id != IMAGE_PAD) ++ return -EINVAL; ++ ++ /* ++ * If a flip has occurred in the sensor, the fmt code might have ++ * changed. So we will need to re-fetch the format from the subdevice. ++ */ ++ ret = __subdev_get_format(dev, &mbus_fmt, node->pad_id); ++ if (ret) ++ return -EINVAL; ++ ++ /* Find the V4L2 format from mbus code. We must match a known format. */ ++ fmt = find_format_by_code(mbus_fmt.code); ++ if (!fmt) ++ return -EINVAL; ++ ++ node->fmt = fmt; ++ node->v_fmt.fmt.pix.pixelformat = fmt->fourcc; ++ *f = node->v_fmt; ++ ++ return 0; ++} ++ ++static ++const struct unicam_fmt *get_first_supported_format(struct unicam_device *dev) ++{ ++ struct v4l2_subdev_mbus_code_enum mbus_code; ++ const struct unicam_fmt *fmt = NULL; ++ unsigned int i; ++ int ret; ++ ++ for (i = 0; ret != -EINVAL && ret != -ENOIOCTLCMD; ++i) { ++ memset(&mbus_code, 0, sizeof(mbus_code)); ++ mbus_code.index = i; ++ mbus_code.pad = IMAGE_PAD; ++ mbus_code.which = V4L2_SUBDEV_FORMAT_ACTIVE; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, NULL, ++ &mbus_code); ++ if (ret < 0) { ++ unicam_dbg(2, dev, ++ "subdev->enum_mbus_code idx %u returned %d - continue\n", ++ i, ret); ++ continue; ++ } ++ ++ unicam_dbg(2, dev, "subdev %s: code: 0x%08x idx: %u\n", ++ dev->sensor->name, mbus_code.code, i); ++ ++ fmt = find_format_by_code(mbus_code.code); ++ unicam_dbg(2, dev, "fmt 0x%08x returned as %p, V4L2 FOURCC 0x%08x, csi_dt 0x%02x\n", ++ mbus_code.code, fmt, fmt ? fmt->fourcc : 0, ++ fmt ? fmt->csi_dt : 0); ++ if (fmt) ++ return fmt; ++ } ++ ++ return NULL; ++} ++ ++static int unicam_try_fmt_vid_cap(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ struct v4l2_subdev_format sd_fmt = { ++ .which = V4L2_SUBDEV_FORMAT_TRY, ++ .pad = IMAGE_PAD ++ }; ++ struct v4l2_mbus_framefmt *mbus_fmt = &sd_fmt.format; ++ const struct unicam_fmt *fmt; ++ int ret; ++ ++ if (node->pad_id != IMAGE_PAD) ++ return -EINVAL; ++ ++ fmt = find_format_by_pix(dev, f->fmt.pix.pixelformat); ++ if (!fmt) { ++ /* ++ * Pixel format not supported by unicam. Choose the first ++ * supported format, and let the sensor choose something else. ++ */ ++ unicam_dbg(3, dev, "Fourcc format (0x%08x) not found. Use first format.\n", ++ f->fmt.pix.pixelformat); ++ ++ fmt = &formats[0]; ++ f->fmt.pix.pixelformat = fmt->fourcc; ++ } ++ ++ v4l2_fill_mbus_format(mbus_fmt, &f->fmt.pix, fmt->code); ++ /* ++ * No support for receiving interlaced video, so never ++ * request it from the sensor subdev. ++ */ ++ mbus_fmt->field = V4L2_FIELD_NONE; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, set_fmt, dev->sensor_config, ++ &sd_fmt); ++ if (ret && ret != -ENOIOCTLCMD && ret != -ENODEV) ++ return ret; ++ ++ if (mbus_fmt->field != V4L2_FIELD_NONE) ++ unicam_info(dev, "Sensor trying to send interlaced video - results may be unpredictable\n"); ++ ++ v4l2_fill_pix_format(&f->fmt.pix, &sd_fmt.format); ++ if (mbus_fmt->code != fmt->code) { ++ /* Sensor has returned an alternate format */ ++ fmt = find_format_by_code(mbus_fmt->code); ++ if (!fmt) { ++ /* ++ * The alternate format is one unicam can't support. ++ * Find the first format that is supported by both, and ++ * then set that. ++ */ ++ fmt = get_first_supported_format(dev); ++ mbus_fmt->code = fmt->code; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, set_fmt, ++ dev->sensor_config, &sd_fmt); ++ if (ret && ret != -ENOIOCTLCMD && ret != -ENODEV) ++ return ret; ++ ++ if (mbus_fmt->field != V4L2_FIELD_NONE) ++ unicam_info(dev, "Sensor trying to send interlaced video - results may be unpredictable\n"); ++ ++ v4l2_fill_pix_format(&f->fmt.pix, &sd_fmt.format); ++ ++ if (mbus_fmt->code != fmt->code) { ++ /* ++ * We've set a format that the sensor reports ++ * as being supported, but it refuses to set it. ++ * Not much else we can do. ++ * Assume that the sensor driver may accept the ++ * format when it is set (rather than tried). ++ */ ++ unicam_err(dev, "Sensor won't accept default format, and Unicam can't support sensor default\n"); ++ } ++ } ++ ++ if (fmt->fourcc) ++ f->fmt.pix.pixelformat = fmt->fourcc; ++ else ++ f->fmt.pix.pixelformat = fmt->repacked_fourcc; ++ } ++ ++ return unicam_calc_format_size_bpl(dev, fmt, f); ++} ++ ++static int unicam_s_fmt_vid_cap(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ struct vb2_queue *q = &node->buffer_queue; ++ struct v4l2_mbus_framefmt mbus_fmt = {0}; ++ const struct unicam_fmt *fmt; ++ int ret; ++ ++ if (vb2_is_busy(q)) ++ return -EBUSY; ++ ++ ret = unicam_try_fmt_vid_cap(file, priv, f); ++ if (ret < 0) ++ return ret; ++ ++ fmt = find_format_by_pix(dev, f->fmt.pix.pixelformat); ++ if (!fmt) { ++ /* ++ * Unknown pixel format - adopt a default. ++ * This shouldn't happen as try_fmt should have resolved any ++ * issues first. ++ */ ++ fmt = get_first_supported_format(dev); ++ if (!fmt) ++ /* ++ * It shouldn't be possible to get here with no ++ * supported formats ++ */ ++ return -EINVAL; ++ f->fmt.pix.pixelformat = fmt->fourcc; ++ return -EINVAL; ++ } ++ ++ v4l2_fill_mbus_format(&mbus_fmt, &f->fmt.pix, fmt->code); ++ ++ ret = __subdev_set_format(dev, &mbus_fmt, node->pad_id); ++ if (ret) { ++ unicam_dbg(3, dev, "%s __subdev_set_format failed %d\n", ++ __func__, ret); ++ return ret; ++ } ++ ++ /* Just double check nothing has gone wrong */ ++ if (mbus_fmt.code != fmt->code) { ++ unicam_dbg(3, dev, ++ "%s subdev changed format on us, this should not happen\n", ++ __func__); ++ return -EINVAL; ++ } ++ ++ node->fmt = fmt; ++ node->v_fmt.fmt.pix.pixelformat = f->fmt.pix.pixelformat; ++ node->v_fmt.fmt.pix.bytesperline = f->fmt.pix.bytesperline; ++ unicam_reset_format(node); ++ ++ unicam_dbg(3, dev, ++ "%s %dx%d, mbus_fmt 0x%08X, V4L2 pix 0x%08X.\n", ++ __func__, node->v_fmt.fmt.pix.width, ++ node->v_fmt.fmt.pix.height, mbus_fmt.code, ++ node->v_fmt.fmt.pix.pixelformat); ++ ++ *f = node->v_fmt; ++ ++ return 0; ++} ++ ++static int unicam_enum_fmt_meta_cap(struct file *file, void *priv, ++ struct v4l2_fmtdesc *f) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ const struct unicam_fmt *fmt; ++ u32 code; ++ int ret = 0; ++ ++ if (node->pad_id != METADATA_PAD || f->index != 0) ++ return -EINVAL; ++ ++ if (dev->sensor_embedded_data) { ++ struct v4l2_subdev_mbus_code_enum mbus_code = { ++ .index = f->index, ++ .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ .pad = METADATA_PAD, ++ }; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, enum_mbus_code, NULL, ++ &mbus_code); ++ if (ret < 0) { ++ unicam_dbg(2, dev, ++ "subdev->enum_mbus_code idx 0 returned %d - index invalid\n", ++ ret); ++ return -EINVAL; ++ } ++ ++ code = mbus_code.code; ++ } else { ++ code = MEDIA_BUS_FMT_SENSOR_DATA; ++ } ++ ++ fmt = find_format_by_code(code); ++ if (fmt) ++ f->pixelformat = fmt->fourcc; ++ ++ return 0; ++} ++ ++static int unicam_g_fmt_meta_cap(struct file *file, void *priv, ++ struct v4l2_format *f) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ ++ if (node->pad_id != METADATA_PAD) ++ return -EINVAL; ++ ++ *f = node->v_fmt; ++ ++ return 0; ++} ++ ++static int unicam_queue_setup(struct vb2_queue *vq, ++ unsigned int *nbuffers, ++ unsigned int *nplanes, ++ unsigned int sizes[], ++ struct device *alloc_devs[]) ++{ ++ struct unicam_node *node = vb2_get_drv_priv(vq); ++ struct unicam_device *dev = node->dev; ++ unsigned int size = node->pad_id == IMAGE_PAD ? ++ node->v_fmt.fmt.pix.sizeimage : ++ node->v_fmt.fmt.meta.buffersize; ++ ++ if (vq->num_buffers + *nbuffers < 3) ++ *nbuffers = 3 - vq->num_buffers; ++ ++ if (*nplanes) { ++ if (sizes[0] < size) { ++ unicam_err(dev, "sizes[0] %i < size %u\n", sizes[0], ++ size); ++ return -EINVAL; ++ } ++ size = sizes[0]; ++ } ++ ++ *nplanes = 1; ++ sizes[0] = size; ++ ++ return 0; ++} ++ ++static int unicam_buffer_prepare(struct vb2_buffer *vb) ++{ ++ struct unicam_node *node = vb2_get_drv_priv(vb->vb2_queue); ++ struct unicam_device *dev = node->dev; ++ struct unicam_buffer *buf = to_unicam_buffer(vb); ++ unsigned long size; ++ ++ if (WARN_ON(!node->fmt)) ++ return -EINVAL; ++ ++ size = node->pad_id == IMAGE_PAD ? node->v_fmt.fmt.pix.sizeimage : ++ node->v_fmt.fmt.meta.buffersize; ++ if (vb2_plane_size(vb, 0) < size) { ++ unicam_err(dev, "data will not fit into plane (%lu < %lu)\n", ++ vb2_plane_size(vb, 0), size); ++ return -EINVAL; ++ } ++ ++ vb2_set_plane_payload(&buf->vb.vb2_buf, 0, size); ++ return 0; ++} ++ ++static void unicam_buffer_queue(struct vb2_buffer *vb) ++{ ++ struct unicam_node *node = vb2_get_drv_priv(vb->vb2_queue); ++ struct unicam_buffer *buf = to_unicam_buffer(vb); ++ unsigned long flags; ++ ++ spin_lock_irqsave(&node->dma_queue_lock, flags); ++ list_add_tail(&buf->list, &node->dma_queue); ++ spin_unlock_irqrestore(&node->dma_queue_lock, flags); ++} ++ ++static void unicam_set_packing_config(struct unicam_device *dev) ++{ ++ u32 pack, unpack; ++ u32 val; ++ ++ if (dev->node[IMAGE_PAD].v_fmt.fmt.pix.pixelformat == ++ dev->node[IMAGE_PAD].fmt->fourcc) { ++ unpack = UNICAM_PUM_NONE; ++ pack = UNICAM_PPM_NONE; ++ } else { ++ switch (dev->node[IMAGE_PAD].fmt->depth) { ++ case 8: ++ unpack = UNICAM_PUM_UNPACK8; ++ break; ++ case 10: ++ unpack = UNICAM_PUM_UNPACK10; ++ break; ++ case 12: ++ unpack = UNICAM_PUM_UNPACK12; ++ break; ++ case 14: ++ unpack = UNICAM_PUM_UNPACK14; ++ break; ++ case 16: ++ unpack = UNICAM_PUM_UNPACK16; ++ break; ++ default: ++ unpack = UNICAM_PUM_NONE; ++ break; ++ } ++ ++ /* Repacking is always to 16bpp */ ++ pack = UNICAM_PPM_PACK16; ++ } ++ ++ val = 0; ++ set_field(&val, unpack, UNICAM_PUM_MASK); ++ set_field(&val, pack, UNICAM_PPM_MASK); ++ reg_write(dev, UNICAM_IPIPE, val); ++} ++ ++static void unicam_cfg_image_id(struct unicam_device *dev) ++{ ++ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { ++ /* CSI2 mode, hardcode VC 0 for now. */ ++ reg_write(dev, UNICAM_IDI0, ++ (0 << 6) | dev->node[IMAGE_PAD].fmt->csi_dt); ++ } else { ++ /* CCP2 mode */ ++ reg_write(dev, UNICAM_IDI0, ++ 0x80 | dev->node[IMAGE_PAD].fmt->csi_dt); ++ } ++} ++ ++static void unicam_enable_ed(struct unicam_device *dev) ++{ ++ u32 val = reg_read(dev, UNICAM_DCS); ++ ++ set_field(&val, 2, UNICAM_EDL_MASK); ++ /* Do not wrap at the end of the embedded data buffer */ ++ set_field(&val, 0, UNICAM_DBOB); ++ ++ reg_write(dev, UNICAM_DCS, val); ++} ++ ++static void unicam_start_rx(struct unicam_device *dev, dma_addr_t *addr) ++{ ++ int line_int_freq = dev->node[IMAGE_PAD].v_fmt.fmt.pix.height >> 2; ++ unsigned int size, i; ++ u32 val; ++ ++ if (line_int_freq < 128) ++ line_int_freq = 128; ++ ++ /* Enable lane clocks */ ++ val = 1; ++ for (i = 0; i < dev->active_data_lanes; i++) ++ val = val << 2 | 1; ++ clk_write(dev, val); ++ ++ /* Basic init */ ++ reg_write(dev, UNICAM_CTRL, UNICAM_MEM); ++ ++ /* Enable analogue control, and leave in reset. */ ++ val = UNICAM_AR; ++ set_field(&val, 7, UNICAM_CTATADJ_MASK); ++ set_field(&val, 7, UNICAM_PTATADJ_MASK); ++ reg_write(dev, UNICAM_ANA, val); ++ usleep_range(1000, 2000); ++ ++ /* Come out of reset */ ++ reg_write_field(dev, UNICAM_ANA, 0, UNICAM_AR); ++ ++ /* Peripheral reset */ ++ reg_write_field(dev, UNICAM_CTRL, 1, UNICAM_CPR); ++ reg_write_field(dev, UNICAM_CTRL, 0, UNICAM_CPR); ++ ++ reg_write_field(dev, UNICAM_CTRL, 0, UNICAM_CPE); ++ ++ /* Enable Rx control. */ ++ val = reg_read(dev, UNICAM_CTRL); ++ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { ++ set_field(&val, UNICAM_CPM_CSI2, UNICAM_CPM_MASK); ++ set_field(&val, UNICAM_DCM_STROBE, UNICAM_DCM_MASK); ++ } else { ++ set_field(&val, UNICAM_CPM_CCP2, UNICAM_CPM_MASK); ++ set_field(&val, dev->bus_flags, UNICAM_DCM_MASK); ++ } ++ /* Packet framer timeout */ ++ set_field(&val, 0xf, UNICAM_PFT_MASK); ++ set_field(&val, 128, UNICAM_OET_MASK); ++ reg_write(dev, UNICAM_CTRL, val); ++ ++ reg_write(dev, UNICAM_IHWIN, 0); ++ reg_write(dev, UNICAM_IVWIN, 0); ++ ++ /* AXI bus access QoS setup */ ++ val = reg_read(dev, UNICAM_PRI); ++ set_field(&val, 0, UNICAM_BL_MASK); ++ set_field(&val, 0, UNICAM_BS_MASK); ++ set_field(&val, 0xe, UNICAM_PP_MASK); ++ set_field(&val, 8, UNICAM_NP_MASK); ++ set_field(&val, 2, UNICAM_PT_MASK); ++ set_field(&val, 1, UNICAM_PE); ++ reg_write(dev, UNICAM_PRI, val); ++ ++ reg_write_field(dev, UNICAM_ANA, 0, UNICAM_DDL); ++ ++ /* Always start in trigger frame capture mode (UNICAM_FCM set) */ ++ val = UNICAM_FSIE | UNICAM_FEIE | UNICAM_FCM | UNICAM_IBOB; ++ set_field(&val, line_int_freq, UNICAM_LCIE_MASK); ++ reg_write(dev, UNICAM_ICTL, val); ++ reg_write(dev, UNICAM_STA, UNICAM_STA_MASK_ALL); ++ reg_write(dev, UNICAM_ISTA, UNICAM_ISTA_MASK_ALL); ++ ++ /* tclk_term_en */ ++ reg_write_field(dev, UNICAM_CLT, 2, UNICAM_CLT1_MASK); ++ /* tclk_settle */ ++ reg_write_field(dev, UNICAM_CLT, 6, UNICAM_CLT2_MASK); ++ /* td_term_en */ ++ reg_write_field(dev, UNICAM_DLT, 2, UNICAM_DLT1_MASK); ++ /* ths_settle */ ++ reg_write_field(dev, UNICAM_DLT, 6, UNICAM_DLT2_MASK); ++ /* trx_enable */ ++ reg_write_field(dev, UNICAM_DLT, 0, UNICAM_DLT3_MASK); ++ ++ reg_write_field(dev, UNICAM_CTRL, 0, UNICAM_SOE); ++ ++ /* Packet compare setup - required to avoid missing frame ends */ ++ val = 0; ++ set_field(&val, 1, UNICAM_PCE); ++ set_field(&val, 1, UNICAM_GI); ++ set_field(&val, 1, UNICAM_CPH); ++ set_field(&val, 0, UNICAM_PCVC_MASK); ++ set_field(&val, 1, UNICAM_PCDT_MASK); ++ reg_write(dev, UNICAM_CMP0, val); ++ ++ /* Enable clock lane and set up terminations */ ++ val = 0; ++ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { ++ /* CSI2 */ ++ set_field(&val, 1, UNICAM_CLE); ++ set_field(&val, 1, UNICAM_CLLPE); ++ if (dev->bus_flags & V4L2_MBUS_CSI2_CONTINUOUS_CLOCK) { ++ set_field(&val, 1, UNICAM_CLTRE); ++ set_field(&val, 1, UNICAM_CLHSE); ++ } ++ } else { ++ /* CCP2 */ ++ set_field(&val, 1, UNICAM_CLE); ++ set_field(&val, 1, UNICAM_CLHSE); ++ set_field(&val, 1, UNICAM_CLTRE); ++ } ++ reg_write(dev, UNICAM_CLK, val); ++ ++ /* ++ * Enable required data lanes with appropriate terminations. ++ * The same value needs to be written to UNICAM_DATn registers for ++ * the active lanes, and 0 for inactive ones. ++ */ ++ val = 0; ++ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { ++ /* CSI2 */ ++ set_field(&val, 1, UNICAM_DLE); ++ set_field(&val, 1, UNICAM_DLLPE); ++ if (dev->bus_flags & V4L2_MBUS_CSI2_CONTINUOUS_CLOCK) { ++ set_field(&val, 1, UNICAM_DLTRE); ++ set_field(&val, 1, UNICAM_DLHSE); ++ } ++ } else { ++ /* CCP2 */ ++ set_field(&val, 1, UNICAM_DLE); ++ set_field(&val, 1, UNICAM_DLHSE); ++ set_field(&val, 1, UNICAM_DLTRE); ++ } ++ reg_write(dev, UNICAM_DAT0, val); ++ ++ if (dev->active_data_lanes == 1) ++ val = 0; ++ reg_write(dev, UNICAM_DAT1, val); ++ ++ if (dev->max_data_lanes > 2) { ++ /* ++ * Registers UNICAM_DAT2 and UNICAM_DAT3 only valid if the ++ * instance supports more than 2 data lanes. ++ */ ++ if (dev->active_data_lanes == 2) ++ val = 0; ++ reg_write(dev, UNICAM_DAT2, val); ++ ++ if (dev->active_data_lanes == 3) ++ val = 0; ++ reg_write(dev, UNICAM_DAT3, val); ++ } ++ ++ reg_write(dev, UNICAM_IBLS, ++ dev->node[IMAGE_PAD].v_fmt.fmt.pix.bytesperline); ++ size = dev->node[IMAGE_PAD].v_fmt.fmt.pix.sizeimage; ++ unicam_wr_dma_addr(dev, addr[IMAGE_PAD], size, IMAGE_PAD); ++ unicam_set_packing_config(dev); ++ unicam_cfg_image_id(dev); ++ ++ val = reg_read(dev, UNICAM_MISC); ++ set_field(&val, 1, UNICAM_FL0); ++ set_field(&val, 1, UNICAM_FL1); ++ reg_write(dev, UNICAM_MISC, val); ++ ++ if (dev->node[METADATA_PAD].streaming && dev->sensor_embedded_data) { ++ size = dev->node[METADATA_PAD].v_fmt.fmt.meta.buffersize; ++ unicam_enable_ed(dev); ++ unicam_wr_dma_addr(dev, addr[METADATA_PAD], size, METADATA_PAD); ++ } ++ ++ /* Enable peripheral */ ++ reg_write_field(dev, UNICAM_CTRL, 1, UNICAM_CPE); ++ ++ /* Load image pointers */ ++ reg_write_field(dev, UNICAM_ICTL, 1, UNICAM_LIP_MASK); ++ ++ /* Load embedded data buffer pointers if needed */ ++ if (dev->node[METADATA_PAD].streaming && dev->sensor_embedded_data) ++ reg_write_field(dev, UNICAM_DCS, 1, UNICAM_LDP); ++ ++ /* ++ * Enable trigger only for the first frame to ++ * sync correctly to the FS from the source. ++ */ ++ reg_write_field(dev, UNICAM_ICTL, 1, UNICAM_TFC); ++} ++ ++static void unicam_disable(struct unicam_device *dev) ++{ ++ /* Analogue lane control disable */ ++ reg_write_field(dev, UNICAM_ANA, 1, UNICAM_DDL); ++ ++ /* Stop the output engine */ ++ reg_write_field(dev, UNICAM_CTRL, 1, UNICAM_SOE); ++ ++ /* Disable the data lanes. */ ++ reg_write(dev, UNICAM_DAT0, 0); ++ reg_write(dev, UNICAM_DAT1, 0); ++ ++ if (dev->max_data_lanes > 2) { ++ reg_write(dev, UNICAM_DAT2, 0); ++ reg_write(dev, UNICAM_DAT3, 0); ++ } ++ ++ /* Peripheral reset */ ++ reg_write_field(dev, UNICAM_CTRL, 1, UNICAM_CPR); ++ usleep_range(50, 100); ++ reg_write_field(dev, UNICAM_CTRL, 0, UNICAM_CPR); ++ ++ /* Disable peripheral */ ++ reg_write_field(dev, UNICAM_CTRL, 0, UNICAM_CPE); ++ ++ /* Clear ED setup */ ++ reg_write(dev, UNICAM_DCS, 0); ++ ++ /* Disable all lane clocks */ ++ clk_write(dev, 0); ++} ++ ++static void unicam_return_buffers(struct unicam_node *node) ++{ ++ struct unicam_buffer *buf, *tmp; ++ unsigned long flags; ++ ++ spin_lock_irqsave(&node->dma_queue_lock, flags); ++ list_for_each_entry_safe(buf, tmp, &node->dma_queue, list) { ++ list_del(&buf->list); ++ vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); ++ } ++ ++ if (node->cur_frm) ++ vb2_buffer_done(&node->cur_frm->vb.vb2_buf, ++ VB2_BUF_STATE_ERROR); ++ if (node->next_frm && node->cur_frm != node->next_frm) ++ vb2_buffer_done(&node->next_frm->vb.vb2_buf, ++ VB2_BUF_STATE_ERROR); ++ ++ node->cur_frm = NULL; ++ node->next_frm = NULL; ++ spin_unlock_irqrestore(&node->dma_queue_lock, flags); ++} ++ ++static int unicam_start_streaming(struct vb2_queue *vq, unsigned int count) ++{ ++ struct unicam_node *node = vb2_get_drv_priv(vq); ++ struct unicam_device *dev = node->dev; ++ dma_addr_t buffer_addr[MAX_NODES] = { 0 }; ++ unsigned long flags; ++ unsigned int i; ++ int ret; ++ ++ node->streaming = true; ++ if (!unicam_all_nodes_streaming(dev)) { ++ unicam_dbg(3, dev, "Not all nodes are streaming yet."); ++ return 0; ++ } ++ ++ dev->sequence = 0; ++ ret = unicam_runtime_get(dev); ++ if (ret < 0) { ++ unicam_dbg(3, dev, "unicam_runtime_get failed\n"); ++ goto err_streaming; ++ } ++ ++ /* ++ * TODO: Retrieve the number of active data lanes from the connected ++ * subdevice. ++ */ ++ dev->active_data_lanes = dev->max_data_lanes; ++ ++ ret = clk_set_rate(dev->clock, 100 * 1000 * 1000); ++ if (ret) { ++ unicam_err(dev, "failed to set up clock\n"); ++ goto err_pm_put; ++ } ++ ++ ret = clk_prepare_enable(dev->clock); ++ if (ret) { ++ unicam_err(dev, "Failed to enable CSI clock: %d\n", ret); ++ goto err_pm_put; ++ } ++ ++ for (i = 0; i < ARRAY_SIZE(dev->node); i++) { ++ struct unicam_buffer *buf; ++ ++ if (!dev->node[i].streaming) ++ continue; ++ ++ spin_lock_irqsave(&dev->node[i].dma_queue_lock, flags); ++ buf = list_first_entry(&dev->node[i].dma_queue, ++ struct unicam_buffer, list); ++ dev->node[i].cur_frm = buf; ++ dev->node[i].next_frm = buf; ++ list_del(&buf->list); ++ spin_unlock_irqrestore(&dev->node[i].dma_queue_lock, flags); ++ ++ buffer_addr[i] = ++ vb2_dma_contig_plane_dma_addr(&buf->vb.vb2_buf, 0); ++ } ++ ++ unicam_start_rx(dev, buffer_addr); ++ ++ ret = v4l2_subdev_call(dev->sensor, video, s_stream, 1); ++ if (ret < 0) { ++ unicam_err(dev, "stream on failed in subdev\n"); ++ goto err_disable_unicam; ++ } ++ ++ return 0; ++ ++err_disable_unicam: ++ unicam_disable(dev); ++ clk_disable_unprepare(dev->clock); ++err_pm_put: ++ unicam_runtime_put(dev); ++err_streaming: ++ unicam_return_buffers(node); ++ node->streaming = false; ++ ++ return ret; ++} ++ ++static void unicam_stop_streaming(struct vb2_queue *vq) ++{ ++ struct unicam_node *node = vb2_get_drv_priv(vq); ++ struct unicam_device *dev = node->dev; ++ ++ node->streaming = false; ++ ++ if (node->pad_id == IMAGE_PAD) { ++ /* ++ * Stop streaming the sensor and disable the peripheral. ++ * We cannot continue streaming embedded data with the ++ * image pad disabled. ++ */ ++ if (v4l2_subdev_call(dev->sensor, video, s_stream, 0) < 0) ++ unicam_err(dev, "stream off failed in subdev\n"); ++ ++ unicam_disable(dev); ++ clk_disable_unprepare(dev->clock); ++ unicam_runtime_put(dev); ++ ++ } else if (node->pad_id == METADATA_PAD) { ++ /* ++ * Allow the hardware to spin in the dummy buffer. ++ * This is only really needed if the embedded data pad is ++ * disabled before the image pad. ++ */ ++ unicam_wr_dma_addr(dev, node->dummy_buf_dma_addr, ++ DUMMY_BUF_SIZE, METADATA_PAD); ++ } ++ ++ /* Clear all queued buffers for the node */ ++ unicam_return_buffers(node); ++} ++ ++static int unicam_enum_input(struct file *file, void *priv, ++ struct v4l2_input *inp) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ ++ if (inp->index != 0) ++ return -EINVAL; ++ ++ inp->type = V4L2_INPUT_TYPE_CAMERA; ++ if (v4l2_subdev_has_op(dev->sensor, video, s_dv_timings)) { ++ inp->capabilities = V4L2_IN_CAP_DV_TIMINGS; ++ inp->std = 0; ++ } else if (v4l2_subdev_has_op(dev->sensor, video, s_std)) { ++ inp->capabilities = V4L2_IN_CAP_STD; ++ if (v4l2_subdev_call(dev->sensor, video, g_tvnorms, &inp->std) ++ < 0) ++ inp->std = V4L2_STD_ALL; ++ } else { ++ inp->capabilities = 0; ++ inp->std = 0; ++ } ++ sprintf(inp->name, "Camera 0"); ++ return 0; ++} ++ ++static int unicam_g_input(struct file *file, void *priv, unsigned int *i) ++{ ++ *i = 0; ++ ++ return 0; ++} ++ ++static int unicam_s_input(struct file *file, void *priv, unsigned int i) ++{ ++ /* ++ * FIXME: Ideally we would like to be able to query the source ++ * subdevice for information over the input connectors it supports, ++ * and map that through in to a call to video_ops->s_routing. ++ * There is no infrastructure support for defining that within ++ * devicetree at present. Until that is implemented we can't ++ * map a user physical connector number to s_routing input number. ++ */ ++ if (i > 0) ++ return -EINVAL; ++ ++ return 0; ++} ++ ++static int unicam_querystd(struct file *file, void *priv, ++ v4l2_std_id *std) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ ++ return v4l2_subdev_call(dev->sensor, video, querystd, std); ++} ++ ++static int unicam_g_std(struct file *file, void *priv, v4l2_std_id *std) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ ++ return v4l2_subdev_call(dev->sensor, video, g_std, std); ++} ++ ++static int unicam_s_std(struct file *file, void *priv, v4l2_std_id std) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ int ret; ++ v4l2_std_id current_std; ++ ++ ret = v4l2_subdev_call(dev->sensor, video, g_std, ¤t_std); ++ if (ret) ++ return ret; ++ ++ if (std == current_std) ++ return 0; ++ ++ if (vb2_is_busy(&node->buffer_queue)) ++ return -EBUSY; ++ ++ ret = v4l2_subdev_call(dev->sensor, video, s_std, std); ++ ++ /* Force recomputation of bytesperline */ ++ node->v_fmt.fmt.pix.bytesperline = 0; ++ ++ unicam_reset_format(node); ++ ++ return ret; ++} ++ ++static int unicam_s_edid(struct file *file, void *priv, struct v4l2_edid *edid) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ ++ return v4l2_subdev_call(dev->sensor, pad, set_edid, edid); ++} ++ ++static int unicam_g_edid(struct file *file, void *priv, struct v4l2_edid *edid) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ ++ return v4l2_subdev_call(dev->sensor, pad, get_edid, edid); ++} ++ ++static int unicam_s_selection(struct file *file, void *priv, ++ struct v4l2_selection *sel) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ struct v4l2_subdev_selection sdsel = { ++ .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ .target = sel->target, ++ .flags = sel->flags, ++ .r = sel->r, ++ }; ++ ++ return v4l2_subdev_call(dev->sensor, pad, set_selection, NULL, &sdsel); ++} ++ ++static int unicam_g_selection(struct file *file, void *priv, ++ struct v4l2_selection *sel) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ struct v4l2_subdev_selection sdsel = { ++ .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ .target = sel->target, ++ }; ++ int ret; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, get_selection, NULL, &sdsel); ++ if (!ret) ++ sel->r = sdsel.r; ++ ++ return ret; ++} ++ ++static int unicam_enum_framesizes(struct file *file, void *priv, ++ struct v4l2_frmsizeenum *fsize) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ const struct unicam_fmt *fmt; ++ struct v4l2_subdev_frame_size_enum fse; ++ int ret; ++ ++ /* check for valid format */ ++ fmt = find_format_by_pix(dev, fsize->pixel_format); ++ if (!fmt) { ++ unicam_dbg(3, dev, "Invalid pixel code: %x\n", ++ fsize->pixel_format); ++ return -EINVAL; ++ } ++ fse.code = fmt->code; ++ ++ fse.which = V4L2_SUBDEV_FORMAT_ACTIVE; ++ fse.index = fsize->index; ++ fse.pad = node->pad_id; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, enum_frame_size, NULL, &fse); ++ if (ret) ++ return ret; ++ ++ unicam_dbg(1, dev, "%s: index: %d code: %x W:[%d,%d] H:[%d,%d]\n", ++ __func__, fse.index, fse.code, fse.min_width, fse.max_width, ++ fse.min_height, fse.max_height); ++ ++ fsize->type = V4L2_FRMSIZE_TYPE_DISCRETE; ++ fsize->discrete.width = fse.max_width; ++ fsize->discrete.height = fse.max_height; ++ ++ return 0; ++} ++ ++static int unicam_enum_frameintervals(struct file *file, void *priv, ++ struct v4l2_frmivalenum *fival) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ const struct unicam_fmt *fmt; ++ struct v4l2_subdev_frame_interval_enum fie = { ++ .index = fival->index, ++ .width = fival->width, ++ .height = fival->height, ++ .which = V4L2_SUBDEV_FORMAT_ACTIVE, ++ }; ++ int ret; ++ ++ fmt = find_format_by_pix(dev, fival->pixel_format); ++ if (!fmt) ++ return -EINVAL; ++ ++ fie.code = fmt->code; ++ ret = v4l2_subdev_call(dev->sensor, pad, enum_frame_interval, ++ NULL, &fie); ++ if (ret) ++ return ret; ++ ++ fival->type = V4L2_FRMIVAL_TYPE_DISCRETE; ++ fival->discrete = fie.interval; ++ ++ return 0; ++} ++ ++static int unicam_g_parm(struct file *file, void *fh, struct v4l2_streamparm *a) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ ++ return v4l2_g_parm_cap(video_devdata(file), dev->sensor, a); ++} ++ ++static int unicam_s_parm(struct file *file, void *fh, struct v4l2_streamparm *a) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ ++ return v4l2_s_parm_cap(video_devdata(file), dev->sensor, a); ++} ++ ++static int unicam_g_dv_timings(struct file *file, void *priv, ++ struct v4l2_dv_timings *timings) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ ++ return v4l2_subdev_call(dev->sensor, video, g_dv_timings, timings); ++} ++ ++static int unicam_s_dv_timings(struct file *file, void *priv, ++ struct v4l2_dv_timings *timings) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ struct v4l2_dv_timings current_timings; ++ int ret; ++ ++ ret = v4l2_subdev_call(dev->sensor, video, g_dv_timings, ++ ¤t_timings); ++ ++ if (v4l2_match_dv_timings(timings, ¤t_timings, 0, false)) ++ return 0; ++ ++ if (vb2_is_busy(&node->buffer_queue)) ++ return -EBUSY; ++ ++ ret = v4l2_subdev_call(dev->sensor, video, s_dv_timings, timings); ++ ++ /* Force recomputation of bytesperline */ ++ node->v_fmt.fmt.pix.bytesperline = 0; ++ ++ unicam_reset_format(node); ++ ++ return ret; ++} ++ ++static int unicam_query_dv_timings(struct file *file, void *priv, ++ struct v4l2_dv_timings *timings) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ ++ return v4l2_subdev_call(dev->sensor, video, query_dv_timings, timings); ++} ++ ++static int unicam_enum_dv_timings(struct file *file, void *priv, ++ struct v4l2_enum_dv_timings *timings) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ ++ return v4l2_subdev_call(dev->sensor, pad, enum_dv_timings, timings); ++} ++ ++static int unicam_dv_timings_cap(struct file *file, void *priv, ++ struct v4l2_dv_timings_cap *cap) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ ++ return v4l2_subdev_call(dev->sensor, pad, dv_timings_cap, cap); ++} ++ ++static int unicam_subscribe_event(struct v4l2_fh *fh, ++ const struct v4l2_event_subscription *sub) ++{ ++ switch (sub->type) { ++ case V4L2_EVENT_FRAME_SYNC: ++ return v4l2_event_subscribe(fh, sub, 2, NULL); ++ case V4L2_EVENT_SOURCE_CHANGE: ++ return v4l2_event_subscribe(fh, sub, 4, NULL); ++ } ++ ++ return v4l2_ctrl_subscribe_event(fh, sub); ++} ++ ++static int unicam_log_status(struct file *file, void *fh) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ u32 reg; ++ ++ /* status for sub devices */ ++ v4l2_device_call_all(&dev->v4l2_dev, 0, core, log_status); ++ ++ unicam_info(dev, "-----Receiver status-----\n"); ++ unicam_info(dev, "V4L2 width/height: %ux%u\n", ++ node->v_fmt.fmt.pix.width, node->v_fmt.fmt.pix.height); ++ unicam_info(dev, "Mediabus format: %08x\n", node->fmt->code); ++ unicam_info(dev, "V4L2 format: %08x\n", ++ node->v_fmt.fmt.pix.pixelformat); ++ reg = reg_read(dev, UNICAM_IPIPE); ++ unicam_info(dev, "Unpacking/packing: %u / %u\n", ++ get_field(reg, UNICAM_PUM_MASK), ++ get_field(reg, UNICAM_PPM_MASK)); ++ unicam_info(dev, "----Live data----\n"); ++ unicam_info(dev, "Programmed stride: %4u\n", ++ reg_read(dev, UNICAM_IBLS)); ++ unicam_info(dev, "Detected resolution: %ux%u\n", ++ reg_read(dev, UNICAM_IHSTA), ++ reg_read(dev, UNICAM_IVSTA)); ++ unicam_info(dev, "Write pointer: %08x\n", ++ reg_read(dev, UNICAM_IBWP)); ++ ++ return 0; ++} ++ ++static void unicam_notify(struct v4l2_subdev *sd, ++ unsigned int notification, void *arg) ++{ ++ struct unicam_device *dev = to_unicam_device(sd->v4l2_dev); ++ ++ switch (notification) { ++ case V4L2_DEVICE_NOTIFY_EVENT: ++ v4l2_event_queue(&dev->node[IMAGE_PAD].video_dev, arg); ++ break; ++ default: ++ break; ++ } ++} ++ ++static const struct vb2_ops unicam_video_qops = { ++ .wait_prepare = vb2_ops_wait_prepare, ++ .wait_finish = vb2_ops_wait_finish, ++ .queue_setup = unicam_queue_setup, ++ .buf_prepare = unicam_buffer_prepare, ++ .buf_queue = unicam_buffer_queue, ++ .start_streaming = unicam_start_streaming, ++ .stop_streaming = unicam_stop_streaming, ++}; ++ ++/* ++ * unicam_v4l2_open : This function is based on the v4l2_fh_open helper ++ * function. It has been augmented to handle sensor subdevice power management, ++ */ ++static int unicam_v4l2_open(struct file *file) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ int ret; ++ ++ mutex_lock(&node->lock); ++ ++ ret = v4l2_fh_open(file); ++ if (ret) { ++ unicam_err(dev, "v4l2_fh_open failed\n"); ++ goto unlock; ++ } ++ ++ node->open++; ++ ++ if (!v4l2_fh_is_singular_file(file)) ++ goto unlock; ++ ++ ret = v4l2_subdev_call(dev->sensor, core, s_power, 1); ++ if (ret < 0 && ret != -ENOIOCTLCMD) { ++ v4l2_fh_release(file); ++ node->open--; ++ goto unlock; ++ } ++ ++ ret = 0; ++ ++unlock: ++ mutex_unlock(&node->lock); ++ return ret; ++} ++ ++static int unicam_v4l2_release(struct file *file) ++{ ++ struct unicam_node *node = video_drvdata(file); ++ struct unicam_device *dev = node->dev; ++ struct v4l2_subdev *sd = dev->sensor; ++ bool fh_singular; ++ int ret; ++ ++ mutex_lock(&node->lock); ++ ++ fh_singular = v4l2_fh_is_singular_file(file); ++ ++ ret = _vb2_fop_release(file, NULL); ++ ++ if (fh_singular) ++ v4l2_subdev_call(sd, core, s_power, 0); ++ ++ node->open--; ++ mutex_unlock(&node->lock); ++ ++ return ret; ++} ++ ++/* unicam capture driver file operations */ ++static const struct v4l2_file_operations unicam_fops = { ++ .owner = THIS_MODULE, ++ .open = unicam_v4l2_open, ++ .release = unicam_v4l2_release, ++ .read = vb2_fop_read, ++ .poll = vb2_fop_poll, ++ .unlocked_ioctl = video_ioctl2, ++ .mmap = vb2_fop_mmap, ++}; ++ ++/* unicam capture ioctl operations */ ++static const struct v4l2_ioctl_ops unicam_ioctl_ops = { ++ .vidioc_querycap = unicam_querycap, ++ .vidioc_enum_fmt_vid_cap = unicam_enum_fmt_vid_cap, ++ .vidioc_g_fmt_vid_cap = unicam_g_fmt_vid_cap, ++ .vidioc_s_fmt_vid_cap = unicam_s_fmt_vid_cap, ++ .vidioc_try_fmt_vid_cap = unicam_try_fmt_vid_cap, ++ ++ .vidioc_enum_fmt_meta_cap = unicam_enum_fmt_meta_cap, ++ .vidioc_g_fmt_meta_cap = unicam_g_fmt_meta_cap, ++ .vidioc_s_fmt_meta_cap = unicam_g_fmt_meta_cap, ++ .vidioc_try_fmt_meta_cap = unicam_g_fmt_meta_cap, ++ ++ .vidioc_enum_input = unicam_enum_input, ++ .vidioc_g_input = unicam_g_input, ++ .vidioc_s_input = unicam_s_input, ++ ++ .vidioc_querystd = unicam_querystd, ++ .vidioc_s_std = unicam_s_std, ++ .vidioc_g_std = unicam_g_std, ++ ++ .vidioc_g_edid = unicam_g_edid, ++ .vidioc_s_edid = unicam_s_edid, ++ ++ .vidioc_enum_framesizes = unicam_enum_framesizes, ++ .vidioc_enum_frameintervals = unicam_enum_frameintervals, ++ ++ .vidioc_g_selection = unicam_g_selection, ++ .vidioc_s_selection = unicam_s_selection, ++ ++ .vidioc_g_parm = unicam_g_parm, ++ .vidioc_s_parm = unicam_s_parm, ++ ++ .vidioc_s_dv_timings = unicam_s_dv_timings, ++ .vidioc_g_dv_timings = unicam_g_dv_timings, ++ .vidioc_query_dv_timings = unicam_query_dv_timings, ++ .vidioc_enum_dv_timings = unicam_enum_dv_timings, ++ .vidioc_dv_timings_cap = unicam_dv_timings_cap, ++ ++ .vidioc_reqbufs = vb2_ioctl_reqbufs, ++ .vidioc_create_bufs = vb2_ioctl_create_bufs, ++ .vidioc_prepare_buf = vb2_ioctl_prepare_buf, ++ .vidioc_querybuf = vb2_ioctl_querybuf, ++ .vidioc_qbuf = vb2_ioctl_qbuf, ++ .vidioc_dqbuf = vb2_ioctl_dqbuf, ++ .vidioc_expbuf = vb2_ioctl_expbuf, ++ .vidioc_streamon = vb2_ioctl_streamon, ++ .vidioc_streamoff = vb2_ioctl_streamoff, ++ ++ .vidioc_log_status = unicam_log_status, ++ .vidioc_subscribe_event = unicam_subscribe_event, ++ .vidioc_unsubscribe_event = v4l2_event_unsubscribe, ++}; ++ ++static int ++unicam_async_bound(struct v4l2_async_notifier *notifier, ++ struct v4l2_subdev *subdev, ++ struct v4l2_async_subdev *asd) ++{ ++ struct unicam_device *unicam = to_unicam_device(notifier->v4l2_dev); ++ ++ if (unicam->sensor) { ++ unicam_info(unicam, "Rejecting subdev %s (Already set!!)", ++ subdev->name); ++ return 0; ++ } ++ ++ unicam->sensor = subdev; ++ unicam_dbg(1, unicam, "Using sensor %s for capture\n", subdev->name); ++ ++ return 0; ++} ++ ++static void unicam_release(struct kref *kref) ++{ ++ struct unicam_device *unicam = ++ container_of(kref, struct unicam_device, kref); ++ ++ v4l2_ctrl_handler_free(&unicam->ctrl_handler); ++ media_device_cleanup(&unicam->mdev); ++ ++ if (unicam->sensor_config) ++ v4l2_subdev_free_pad_config(unicam->sensor_config); ++ ++ kfree(unicam); ++} ++ ++static void unicam_put(struct unicam_device *unicam) ++{ ++ kref_put(&unicam->kref, unicam_release); ++} ++ ++static void unicam_get(struct unicam_device *unicam) ++{ ++ kref_get(&unicam->kref); ++} ++ ++static void unicam_node_release(struct video_device *vdev) ++{ ++ struct unicam_node *node = video_get_drvdata(vdev); ++ ++ unicam_put(node->dev); ++} ++ ++static int register_node(struct unicam_device *unicam, struct unicam_node *node, ++ enum v4l2_buf_type type, int pad_id) ++{ ++ struct video_device *vdev; ++ struct vb2_queue *q; ++ struct v4l2_mbus_framefmt mbus_fmt = {0}; ++ const struct unicam_fmt *fmt; ++ int ret; ++ ++ if (pad_id == IMAGE_PAD) { ++ ret = __subdev_get_format(unicam, &mbus_fmt, pad_id); ++ if (ret) { ++ unicam_err(unicam, "Failed to get_format - ret %d\n", ++ ret); ++ return ret; ++ } ++ ++ fmt = find_format_by_code(mbus_fmt.code); ++ if (!fmt) { ++ /* ++ * Find the first format that the sensor and unicam both ++ * support ++ */ ++ fmt = get_first_supported_format(unicam); ++ ++ if (!fmt) ++ /* No compatible formats */ ++ return -EINVAL; ++ ++ mbus_fmt.code = fmt->code; ++ ret = __subdev_set_format(unicam, &mbus_fmt, pad_id); ++ if (ret) ++ return -EINVAL; ++ } ++ if (mbus_fmt.field != V4L2_FIELD_NONE) { ++ /* Interlaced not supported - disable it now. */ ++ mbus_fmt.field = V4L2_FIELD_NONE; ++ ret = __subdev_set_format(unicam, &mbus_fmt, pad_id); ++ if (ret) ++ return -EINVAL; ++ } ++ ++ node->v_fmt.fmt.pix.pixelformat = fmt->fourcc ? fmt->fourcc ++ : fmt->repacked_fourcc; ++ } else { ++ /* Fix this node format as embedded data. */ ++ fmt = find_format_by_code(MEDIA_BUS_FMT_SENSOR_DATA); ++ node->v_fmt.fmt.meta.dataformat = fmt->fourcc; ++ } ++ ++ node->dev = unicam; ++ node->pad_id = pad_id; ++ node->fmt = fmt; ++ ++ /* Read current subdev format */ ++ unicam_reset_format(node); ++ ++ if (v4l2_subdev_has_op(unicam->sensor, video, s_std)) { ++ v4l2_std_id tvnorms; ++ ++ if (WARN_ON(!v4l2_subdev_has_op(unicam->sensor, video, ++ g_tvnorms))) ++ /* ++ * Subdevice should not advertise s_std but not ++ * g_tvnorms ++ */ ++ return -EINVAL; ++ ++ ret = v4l2_subdev_call(unicam->sensor, video, ++ g_tvnorms, &tvnorms); ++ if (WARN_ON(ret)) ++ return -EINVAL; ++ node->video_dev.tvnorms |= tvnorms; ++ } ++ ++ spin_lock_init(&node->dma_queue_lock); ++ mutex_init(&node->lock); ++ ++ vdev = &node->video_dev; ++ if (pad_id == IMAGE_PAD) { ++ /* Add controls from the subdevice */ ++ ret = v4l2_ctrl_add_handler(&unicam->ctrl_handler, ++ unicam->sensor->ctrl_handler, NULL, ++ true); ++ if (ret < 0) ++ return ret; ++ ++ /* ++ * If the sensor subdevice has any controls, associate the node ++ * with the ctrl handler to allow access from userland. ++ */ ++ if (!list_empty(&unicam->ctrl_handler.ctrls)) ++ vdev->ctrl_handler = &unicam->ctrl_handler; ++ } ++ ++ q = &node->buffer_queue; ++ q->type = type; ++ q->io_modes = VB2_MMAP | VB2_DMABUF | VB2_READ; ++ q->drv_priv = node; ++ q->ops = &unicam_video_qops; ++ q->mem_ops = &vb2_dma_contig_memops; ++ q->buf_struct_size = sizeof(struct unicam_buffer); ++ q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC; ++ q->lock = &node->lock; ++ q->min_buffers_needed = 2; ++ q->dev = &unicam->pdev->dev; ++ ++ ret = vb2_queue_init(q); ++ if (ret) { ++ unicam_err(unicam, "vb2_queue_init() failed\n"); ++ return ret; ++ } ++ ++ INIT_LIST_HEAD(&node->dma_queue); ++ ++ vdev->release = unicam_node_release; ++ vdev->fops = &unicam_fops; ++ vdev->ioctl_ops = &unicam_ioctl_ops; ++ vdev->v4l2_dev = &unicam->v4l2_dev; ++ vdev->vfl_dir = VFL_DIR_RX; ++ vdev->queue = q; ++ vdev->lock = &node->lock; ++ vdev->device_caps = (pad_id == IMAGE_PAD) ? ++ (V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING) : ++ (V4L2_CAP_META_CAPTURE | V4L2_CAP_STREAMING); ++ ++ /* Define the device names */ ++ snprintf(vdev->name, sizeof(vdev->name), "%s-%s", UNICAM_MODULE_NAME, ++ pad_id == IMAGE_PAD ? "image" : "embedded"); ++ ++ video_set_drvdata(vdev, node); ++ if (pad_id == IMAGE_PAD) ++ vdev->entity.flags |= MEDIA_ENT_FL_DEFAULT; ++ node->pad.flags = MEDIA_PAD_FL_SINK; ++ media_entity_pads_init(&vdev->entity, 1, &node->pad); ++ ++ node->dummy_buf_cpu_addr = dma_alloc_coherent(&unicam->pdev->dev, ++ DUMMY_BUF_SIZE, ++ &node->dummy_buf_dma_addr, ++ GFP_KERNEL); ++ if (!node->dummy_buf_cpu_addr) { ++ unicam_err(unicam, "Unable to allocate dummy buffer.\n"); ++ return -ENOMEM; ++ } ++ ++ if (pad_id == METADATA_PAD) { ++ v4l2_disable_ioctl(vdev, VIDIOC_DQEVENT); ++ v4l2_disable_ioctl(vdev, VIDIOC_SUBSCRIBE_EVENT); ++ v4l2_disable_ioctl(vdev, VIDIOC_UNSUBSCRIBE_EVENT); ++ } ++ if (pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, video, s_std)) { ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_STD); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_STD); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_ENUMSTD); ++ } ++ if (pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, video, querystd)) ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_QUERYSTD); ++ if (pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, video, s_dv_timings)) { ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_EDID); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_EDID); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_DV_TIMINGS_CAP); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_DV_TIMINGS); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_DV_TIMINGS); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_ENUM_DV_TIMINGS); ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_QUERY_DV_TIMINGS); ++ } ++ if (pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, pad, enum_frame_interval)) ++ v4l2_disable_ioctl(&node->video_dev, ++ VIDIOC_ENUM_FRAMEINTERVALS); ++ if (pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, video, g_frame_interval)) ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_PARM); ++ if (pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, video, s_frame_interval)) ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_PARM); ++ ++ if (pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, pad, enum_frame_size)) ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_ENUM_FRAMESIZES); ++ ++ if (node->pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, pad, set_selection)) ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_SELECTION); ++ ++ if (node->pad_id == METADATA_PAD || ++ !v4l2_subdev_has_op(unicam->sensor, pad, get_selection)) ++ v4l2_disable_ioctl(&node->video_dev, VIDIOC_G_SELECTION); ++ ++ ret = video_register_device(vdev, VFL_TYPE_VIDEO, -1); ++ if (ret) { ++ unicam_err(unicam, "Unable to register video device %s\n", ++ vdev->name); ++ return ret; ++ } ++ ++ /* ++ * Acquire a reference to unicam, which will be released when the video ++ * device will be unregistered and userspace will have closed all open ++ * file handles. ++ */ ++ unicam_get(unicam); ++ node->registered = true; ++ ++ if (pad_id != METADATA_PAD || unicam->sensor_embedded_data) { ++ ret = media_create_pad_link(&unicam->sensor->entity, pad_id, ++ &node->video_dev.entity, 0, ++ MEDIA_LNK_FL_ENABLED | ++ MEDIA_LNK_FL_IMMUTABLE); ++ if (ret) ++ unicam_err(unicam, "Unable to create pad link for %s\n", ++ vdev->name); ++ } ++ ++ return ret; ++} ++ ++static void unregister_nodes(struct unicam_device *unicam) ++{ ++ unsigned int i; ++ ++ for (i = 0; i < ARRAY_SIZE(unicam->node); i++) { ++ struct unicam_node *node = &unicam->node[i]; ++ ++ if (node->dummy_buf_cpu_addr) { ++ dma_free_coherent(&unicam->pdev->dev, DUMMY_BUF_SIZE, ++ node->dummy_buf_cpu_addr, ++ node->dummy_buf_dma_addr); ++ } ++ ++ if (node->registered) { ++ node->registered = false; ++ video_unregister_device(&node->video_dev); ++ } ++ } ++} ++ ++static int unicam_probe_complete(struct unicam_device *unicam) ++{ ++ int ret; ++ ++ unicam->v4l2_dev.notify = unicam_notify; ++ ++ unicam->sensor_config = v4l2_subdev_alloc_pad_config(unicam->sensor); ++ if (!unicam->sensor_config) ++ return -ENOMEM; ++ ++ unicam->sensor_embedded_data = (unicam->sensor->entity.num_pads >= 2); ++ ++ ret = register_node(unicam, &unicam->node[IMAGE_PAD], ++ V4L2_BUF_TYPE_VIDEO_CAPTURE, IMAGE_PAD); ++ if (ret) { ++ unicam_err(unicam, "Unable to register image video device.\n"); ++ goto unregister; ++ } ++ ++ ret = register_node(unicam, &unicam->node[METADATA_PAD], ++ V4L2_BUF_TYPE_META_CAPTURE, METADATA_PAD); ++ if (ret) { ++ unicam_err(unicam, "Unable to register metadata video device.\n"); ++ goto unregister; ++ } ++ ++ ret = v4l2_device_register_ro_subdev_nodes(&unicam->v4l2_dev); ++ if (ret) { ++ unicam_err(unicam, "Unable to register subdev nodes.\n"); ++ goto unregister; ++ } ++ ++ /* ++ * Release the initial reference, all references are now owned by the ++ * video devices. ++ */ ++ unicam_put(unicam); ++ return 0; ++ ++unregister: ++ unregister_nodes(unicam); ++ unicam_put(unicam); ++ ++ return ret; ++} ++ ++static int unicam_async_complete(struct v4l2_async_notifier *notifier) ++{ ++ struct unicam_device *unicam = to_unicam_device(notifier->v4l2_dev); ++ ++ return unicam_probe_complete(unicam); ++} ++ ++static const struct v4l2_async_notifier_operations unicam_async_ops = { ++ .bound = unicam_async_bound, ++ .complete = unicam_async_complete, ++}; ++ ++static int of_unicam_connect_subdevs(struct unicam_device *dev) ++{ ++ struct platform_device *pdev = dev->pdev; ++ struct v4l2_fwnode_endpoint ep = { 0 }; ++ struct device_node *ep_node; ++ struct device_node *sensor_node; ++ unsigned int lane; ++ int ret = -EINVAL; ++ ++ if (of_property_read_u32(pdev->dev.of_node, "brcm,num-data-lanes", ++ &dev->max_data_lanes) < 0) { ++ unicam_err(dev, "number of data lanes not set\n"); ++ return -EINVAL; ++ } ++ ++ /* Get the local endpoint and remote device. */ ++ ep_node = of_graph_get_next_endpoint(pdev->dev.of_node, NULL); ++ if (!ep_node) { ++ unicam_dbg(3, dev, "can't get next endpoint\n"); ++ return -EINVAL; ++ } ++ ++ unicam_dbg(3, dev, "ep_node is %pOF\n", ep_node); ++ ++ sensor_node = of_graph_get_remote_port_parent(ep_node); ++ if (!sensor_node) { ++ unicam_dbg(3, dev, "can't get remote parent\n"); ++ goto cleanup_exit; ++ } ++ ++ unicam_dbg(1, dev, "found subdevice %pOF\n", sensor_node); ++ ++ /* Parse the local endpoint and validate its configuration. */ ++ v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep_node), &ep); ++ ++ unicam_dbg(3, dev, "parsed local endpoint, bus_type %u\n", ++ ep.bus_type); ++ ++ dev->bus_type = ep.bus_type; ++ ++ switch (ep.bus_type) { ++ case V4L2_MBUS_CSI2_DPHY: ++ switch (ep.bus.mipi_csi2.num_data_lanes) { ++ case 1: ++ case 2: ++ case 4: ++ break; ++ ++ default: ++ unicam_err(dev, "subdevice %pOF: %u data lanes not supported\n", ++ sensor_node, ++ ep.bus.mipi_csi2.num_data_lanes); ++ goto cleanup_exit; ++ } ++ ++ for (lane = 0; lane < ep.bus.mipi_csi2.num_data_lanes; lane++) { ++ if (ep.bus.mipi_csi2.data_lanes[lane] != lane + 1) { ++ unicam_err(dev, "subdevice %pOF: data lanes reordering not supported\n", ++ sensor_node); ++ goto cleanup_exit; ++ } ++ } ++ ++ if (ep.bus.mipi_csi2.num_data_lanes > dev->max_data_lanes) { ++ unicam_err(dev, "subdevice requires %u data lanes when %u are supported\n", ++ ep.bus.mipi_csi2.num_data_lanes, ++ dev->max_data_lanes); ++ } ++ ++ dev->max_data_lanes = ep.bus.mipi_csi2.num_data_lanes; ++ dev->bus_flags = ep.bus.mipi_csi2.flags; ++ ++ break; ++ ++ case V4L2_MBUS_CCP2: ++ if (ep.bus.mipi_csi1.clock_lane != 0 || ++ ep.bus.mipi_csi1.data_lane != 1) { ++ unicam_err(dev, "subdevice %pOF: unsupported lanes configuration\n", ++ sensor_node); ++ goto cleanup_exit; ++ } ++ ++ dev->max_data_lanes = 1; ++ dev->bus_flags = ep.bus.mipi_csi1.strobe; ++ break; ++ ++ default: ++ /* Unsupported bus type */ ++ unicam_err(dev, "subdevice %pOF: unsupported bus type %u\n", ++ sensor_node, ep.bus_type); ++ goto cleanup_exit; ++ } ++ ++ unicam_dbg(3, dev, "subdevice %pOF: %s bus, %u data lanes, flags=0x%08x\n", ++ sensor_node, ++ dev->bus_type == V4L2_MBUS_CSI2_DPHY ? "CSI-2" : "CCP2", ++ dev->max_data_lanes, dev->bus_flags); ++ ++ /* Initialize and register the async notifier. */ ++ v4l2_async_notifier_init(&dev->notifier); ++ dev->notifier.ops = &unicam_async_ops; ++ ++ dev->asd.match_type = V4L2_ASYNC_MATCH_FWNODE; ++ dev->asd.match.fwnode = of_fwnode_handle(sensor_node); ++ ret = v4l2_async_notifier_add_subdev(&dev->notifier, &dev->asd); ++ if (ret) { ++ unicam_err(dev, "Error adding subdevice: %d\n", ret); ++ goto cleanup_exit; ++ } ++ ++ ret = v4l2_async_notifier_register(&dev->v4l2_dev, &dev->notifier); ++ if (ret) { ++ unicam_err(dev, "Error registering async notifier: %d\n", ret); ++ ret = -EINVAL; ++ } ++ ++cleanup_exit: ++ of_node_put(sensor_node); ++ of_node_put(ep_node); ++ ++ return ret; ++} ++ ++static int unicam_probe(struct platform_device *pdev) ++{ ++ struct unicam_device *unicam; ++ int ret; ++ ++ unicam = kzalloc(sizeof(*unicam), GFP_KERNEL); ++ if (!unicam) ++ return -ENOMEM; ++ ++ kref_init(&unicam->kref); ++ unicam->pdev = pdev; ++ ++ unicam->base = devm_platform_ioremap_resource(pdev, 0); ++ if (IS_ERR(unicam->base)) { ++ unicam_err(unicam, "Failed to get main io block\n"); ++ ret = PTR_ERR(unicam->base); ++ goto err_unicam_put; ++ } ++ ++ unicam->clk_gate_base = devm_platform_ioremap_resource(pdev, 1); ++ if (IS_ERR(unicam->clk_gate_base)) { ++ unicam_err(unicam, "Failed to get 2nd io block\n"); ++ ret = PTR_ERR(unicam->clk_gate_base); ++ goto err_unicam_put; ++ } ++ ++ unicam->clock = devm_clk_get(&pdev->dev, "lp"); ++ if (IS_ERR(unicam->clock)) { ++ unicam_err(unicam, "Failed to get clock\n"); ++ ret = PTR_ERR(unicam->clock); ++ goto err_unicam_put; ++ } ++ ++ ret = platform_get_irq(pdev, 0); ++ if (ret <= 0) { ++ dev_err(&pdev->dev, "No IRQ resource\n"); ++ ret = -EINVAL; ++ goto err_unicam_put; ++ } ++ ++ ret = devm_request_irq(&pdev->dev, ret, unicam_isr, 0, ++ "unicam_capture0", unicam); ++ if (ret) { ++ dev_err(&pdev->dev, "Unable to request interrupt\n"); ++ ret = -EINVAL; ++ goto err_unicam_put; ++ } ++ ++ unicam->mdev.dev = &pdev->dev; ++ strscpy(unicam->mdev.model, UNICAM_MODULE_NAME, ++ sizeof(unicam->mdev.model)); ++ strscpy(unicam->mdev.serial, "", sizeof(unicam->mdev.serial)); ++ snprintf(unicam->mdev.bus_info, sizeof(unicam->mdev.bus_info), ++ "platform:%s", dev_name(&pdev->dev)); ++ unicam->mdev.hw_revision = 0; ++ ++ media_device_init(&unicam->mdev); ++ ++ unicam->v4l2_dev.mdev = &unicam->mdev; ++ ++ ret = v4l2_device_register(&pdev->dev, &unicam->v4l2_dev); ++ if (ret) { ++ unicam_err(unicam, ++ "Unable to register v4l2 device.\n"); ++ goto err_unicam_put; ++ } ++ ++ ret = media_device_register(&unicam->mdev); ++ if (ret < 0) { ++ unicam_err(unicam, ++ "Unable to register media-controller device.\n"); ++ goto err_v4l2_unregister; ++ } ++ ++ /* Reserve space for the controls */ ++ ret = v4l2_ctrl_handler_init(&unicam->ctrl_handler, 16); ++ if (ret < 0) ++ goto err_media_unregister; ++ ++ /* set the driver data in platform device */ ++ platform_set_drvdata(pdev, unicam); ++ ++ ret = of_unicam_connect_subdevs(unicam); ++ if (ret) { ++ dev_err(&pdev->dev, "Failed to connect subdevs\n"); ++ goto err_media_unregister; ++ } ++ ++ /* Enable the block power domain */ ++ pm_runtime_enable(&pdev->dev); ++ ++ return 0; ++ ++err_media_unregister: ++ media_device_unregister(&unicam->mdev); ++err_v4l2_unregister: ++ v4l2_device_unregister(&unicam->v4l2_dev); ++err_unicam_put: ++ unicam_put(unicam); ++ ++ return ret; ++} ++ ++static int unicam_remove(struct platform_device *pdev) ++{ ++ struct unicam_device *unicam = platform_get_drvdata(pdev); ++ ++ unicam_dbg(2, unicam, "%s\n", __func__); ++ ++ v4l2_async_notifier_unregister(&unicam->notifier); ++ v4l2_device_unregister(&unicam->v4l2_dev); ++ media_device_unregister(&unicam->mdev); ++ unregister_nodes(unicam); ++ ++ pm_runtime_disable(&pdev->dev); ++ ++ return 0; ++} ++ ++static const struct of_device_id unicam_of_match[] = { ++ { .compatible = "brcm,bcm2835-unicam", }, ++ { /* sentinel */ }, ++}; ++MODULE_DEVICE_TABLE(of, unicam_of_match); ++ ++static struct platform_driver unicam_driver = { ++ .probe = unicam_probe, ++ .remove = unicam_remove, ++ .driver = { ++ .name = UNICAM_MODULE_NAME, ++ .of_match_table = of_match_ptr(unicam_of_match), ++ }, ++}; ++ ++module_platform_driver(unicam_driver); ++ ++MODULE_AUTHOR("Dave Stevenson "); ++MODULE_DESCRIPTION("BCM2835 Unicam driver"); ++MODULE_LICENSE("GPL"); ++MODULE_VERSION(UNICAM_VERSION); +--- /dev/null ++++ b/drivers/media/platform/bcm2835/vc4-regs-unicam.h +@@ -0,0 +1,253 @@ ++/* SPDX-License-Identifier: GPL-2.0-only */ ++ ++/* ++ * Copyright (C) 2017-2020 Raspberry Pi Trading. ++ * Dave Stevenson ++ */ ++ ++#ifndef VC4_REGS_UNICAM_H ++#define VC4_REGS_UNICAM_H ++ ++/* ++ * The following values are taken from files found within the code drop ++ * made by Broadcom for the BCM21553 Graphics Driver, predominantly in ++ * brcm_usrlib/dag/vmcsx/vcinclude/hardware_vc4.h. ++ * They have been modified to be only the register offset. ++ */ ++#define UNICAM_CTRL 0x000 ++#define UNICAM_STA 0x004 ++#define UNICAM_ANA 0x008 ++#define UNICAM_PRI 0x00c ++#define UNICAM_CLK 0x010 ++#define UNICAM_CLT 0x014 ++#define UNICAM_DAT0 0x018 ++#define UNICAM_DAT1 0x01c ++#define UNICAM_DAT2 0x020 ++#define UNICAM_DAT3 0x024 ++#define UNICAM_DLT 0x028 ++#define UNICAM_CMP0 0x02c ++#define UNICAM_CMP1 0x030 ++#define UNICAM_CAP0 0x034 ++#define UNICAM_CAP1 0x038 ++#define UNICAM_ICTL 0x100 ++#define UNICAM_ISTA 0x104 ++#define UNICAM_IDI0 0x108 ++#define UNICAM_IPIPE 0x10c ++#define UNICAM_IBSA0 0x110 ++#define UNICAM_IBEA0 0x114 ++#define UNICAM_IBLS 0x118 ++#define UNICAM_IBWP 0x11c ++#define UNICAM_IHWIN 0x120 ++#define UNICAM_IHSTA 0x124 ++#define UNICAM_IVWIN 0x128 ++#define UNICAM_IVSTA 0x12c ++#define UNICAM_ICC 0x130 ++#define UNICAM_ICS 0x134 ++#define UNICAM_IDC 0x138 ++#define UNICAM_IDPO 0x13c ++#define UNICAM_IDCA 0x140 ++#define UNICAM_IDCD 0x144 ++#define UNICAM_IDS 0x148 ++#define UNICAM_DCS 0x200 ++#define UNICAM_DBSA0 0x204 ++#define UNICAM_DBEA0 0x208 ++#define UNICAM_DBWP 0x20c ++#define UNICAM_DBCTL 0x300 ++#define UNICAM_IBSA1 0x304 ++#define UNICAM_IBEA1 0x308 ++#define UNICAM_IDI1 0x30c ++#define UNICAM_DBSA1 0x310 ++#define UNICAM_DBEA1 0x314 ++#define UNICAM_MISC 0x400 ++ ++/* ++ * The following bitmasks are from the kernel released by Broadcom ++ * for Android - https://android.googlesource.com/kernel/bcm/ ++ * The Rhea, Hawaii, and Java chips all contain the same VideoCore4 ++ * Unicam block as BCM2835, as defined in eg ++ * arch/arm/mach-rhea/include/mach/rdb_A0/brcm_rdb_cam.h and similar. ++ * Values reworked to use the kernel BIT and GENMASK macros. ++ * ++ * Some of the bit mnenomics have been amended to match the datasheet. ++ */ ++/* UNICAM_CTRL Register */ ++#define UNICAM_CPE BIT(0) ++#define UNICAM_MEM BIT(1) ++#define UNICAM_CPR BIT(2) ++#define UNICAM_CPM_MASK GENMASK(3, 3) ++#define UNICAM_CPM_CSI2 0 ++#define UNICAM_CPM_CCP2 1 ++#define UNICAM_SOE BIT(4) ++#define UNICAM_DCM_MASK GENMASK(5, 5) ++#define UNICAM_DCM_STROBE 0 ++#define UNICAM_DCM_DATA 1 ++#define UNICAM_SLS BIT(6) ++#define UNICAM_PFT_MASK GENMASK(11, 8) ++#define UNICAM_OET_MASK GENMASK(20, 12) ++ ++/* UNICAM_STA Register */ ++#define UNICAM_SYN BIT(0) ++#define UNICAM_CS BIT(1) ++#define UNICAM_SBE BIT(2) ++#define UNICAM_PBE BIT(3) ++#define UNICAM_HOE BIT(4) ++#define UNICAM_PLE BIT(5) ++#define UNICAM_SSC BIT(6) ++#define UNICAM_CRCE BIT(7) ++#define UNICAM_OES BIT(8) ++#define UNICAM_IFO BIT(9) ++#define UNICAM_OFO BIT(10) ++#define UNICAM_BFO BIT(11) ++#define UNICAM_DL BIT(12) ++#define UNICAM_PS BIT(13) ++#define UNICAM_IS BIT(14) ++#define UNICAM_PI0 BIT(15) ++#define UNICAM_PI1 BIT(16) ++#define UNICAM_FSI_S BIT(17) ++#define UNICAM_FEI_S BIT(18) ++#define UNICAM_LCI_S BIT(19) ++#define UNICAM_BUF0_RDY BIT(20) ++#define UNICAM_BUF0_NO BIT(21) ++#define UNICAM_BUF1_RDY BIT(22) ++#define UNICAM_BUF1_NO BIT(23) ++#define UNICAM_DI BIT(24) ++ ++#define UNICAM_STA_MASK_ALL \ ++ (UNICAM_DL + \ ++ UNICAM_SBE + \ ++ UNICAM_PBE + \ ++ UNICAM_HOE + \ ++ UNICAM_PLE + \ ++ UNICAM_SSC + \ ++ UNICAM_CRCE + \ ++ UNICAM_IFO + \ ++ UNICAM_OFO + \ ++ UNICAM_PS + \ ++ UNICAM_PI0 + \ ++ UNICAM_PI1) ++ ++/* UNICAM_ANA Register */ ++#define UNICAM_APD BIT(0) ++#define UNICAM_BPD BIT(1) ++#define UNICAM_AR BIT(2) ++#define UNICAM_DDL BIT(3) ++#define UNICAM_CTATADJ_MASK GENMASK(7, 4) ++#define UNICAM_PTATADJ_MASK GENMASK(11, 8) ++ ++/* UNICAM_PRI Register */ ++#define UNICAM_PE BIT(0) ++#define UNICAM_PT_MASK GENMASK(2, 1) ++#define UNICAM_NP_MASK GENMASK(7, 4) ++#define UNICAM_PP_MASK GENMASK(11, 8) ++#define UNICAM_BS_MASK GENMASK(15, 12) ++#define UNICAM_BL_MASK GENMASK(17, 16) ++ ++/* UNICAM_CLK Register */ ++#define UNICAM_CLE BIT(0) ++#define UNICAM_CLPD BIT(1) ++#define UNICAM_CLLPE BIT(2) ++#define UNICAM_CLHSE BIT(3) ++#define UNICAM_CLTRE BIT(4) ++#define UNICAM_CLAC_MASK GENMASK(8, 5) ++#define UNICAM_CLSTE BIT(29) ++ ++/* UNICAM_CLT Register */ ++#define UNICAM_CLT1_MASK GENMASK(7, 0) ++#define UNICAM_CLT2_MASK GENMASK(15, 8) ++ ++/* UNICAM_DATn Registers */ ++#define UNICAM_DLE BIT(0) ++#define UNICAM_DLPD BIT(1) ++#define UNICAM_DLLPE BIT(2) ++#define UNICAM_DLHSE BIT(3) ++#define UNICAM_DLTRE BIT(4) ++#define UNICAM_DLSM BIT(5) ++#define UNICAM_DLFO BIT(28) ++#define UNICAM_DLSTE BIT(29) ++ ++#define UNICAM_DAT_MASK_ALL (UNICAM_DLSTE + UNICAM_DLFO) ++ ++/* UNICAM_DLT Register */ ++#define UNICAM_DLT1_MASK GENMASK(7, 0) ++#define UNICAM_DLT2_MASK GENMASK(15, 8) ++#define UNICAM_DLT3_MASK GENMASK(23, 16) ++ ++/* UNICAM_ICTL Register */ ++#define UNICAM_FSIE BIT(0) ++#define UNICAM_FEIE BIT(1) ++#define UNICAM_IBOB BIT(2) ++#define UNICAM_FCM BIT(3) ++#define UNICAM_TFC BIT(4) ++#define UNICAM_LIP_MASK GENMASK(6, 5) ++#define UNICAM_LCIE_MASK GENMASK(28, 16) ++ ++/* UNICAM_IDI0/1 Register */ ++#define UNICAM_ID0_MASK GENMASK(7, 0) ++#define UNICAM_ID1_MASK GENMASK(15, 8) ++#define UNICAM_ID2_MASK GENMASK(23, 16) ++#define UNICAM_ID3_MASK GENMASK(31, 24) ++ ++/* UNICAM_ISTA Register */ ++#define UNICAM_FSI BIT(0) ++#define UNICAM_FEI BIT(1) ++#define UNICAM_LCI BIT(2) ++ ++#define UNICAM_ISTA_MASK_ALL (UNICAM_FSI + UNICAM_FEI + UNICAM_LCI) ++ ++/* UNICAM_IPIPE Register */ ++#define UNICAM_PUM_MASK GENMASK(2, 0) ++ /* Unpacking modes */ ++ #define UNICAM_PUM_NONE 0 ++ #define UNICAM_PUM_UNPACK6 1 ++ #define UNICAM_PUM_UNPACK7 2 ++ #define UNICAM_PUM_UNPACK8 3 ++ #define UNICAM_PUM_UNPACK10 4 ++ #define UNICAM_PUM_UNPACK12 5 ++ #define UNICAM_PUM_UNPACK14 6 ++ #define UNICAM_PUM_UNPACK16 7 ++#define UNICAM_DDM_MASK GENMASK(6, 3) ++#define UNICAM_PPM_MASK GENMASK(9, 7) ++ /* Packing modes */ ++ #define UNICAM_PPM_NONE 0 ++ #define UNICAM_PPM_PACK8 1 ++ #define UNICAM_PPM_PACK10 2 ++ #define UNICAM_PPM_PACK12 3 ++ #define UNICAM_PPM_PACK14 4 ++ #define UNICAM_PPM_PACK16 5 ++#define UNICAM_DEM_MASK GENMASK(11, 10) ++#define UNICAM_DEBL_MASK GENMASK(14, 12) ++#define UNICAM_ICM_MASK GENMASK(16, 15) ++#define UNICAM_IDM_MASK GENMASK(17, 17) ++ ++/* UNICAM_ICC Register */ ++#define UNICAM_ICFL_MASK GENMASK(4, 0) ++#define UNICAM_ICFH_MASK GENMASK(9, 5) ++#define UNICAM_ICST_MASK GENMASK(12, 10) ++#define UNICAM_ICLT_MASK GENMASK(15, 13) ++#define UNICAM_ICLL_MASK GENMASK(31, 16) ++ ++/* UNICAM_DCS Register */ ++#define UNICAM_DIE BIT(0) ++#define UNICAM_DIM BIT(1) ++#define UNICAM_DBOB BIT(3) ++#define UNICAM_FDE BIT(4) ++#define UNICAM_LDP BIT(5) ++#define UNICAM_EDL_MASK GENMASK(15, 8) ++ ++/* UNICAM_DBCTL Register */ ++#define UNICAM_DBEN BIT(0) ++#define UNICAM_BUF0_IE BIT(1) ++#define UNICAM_BUF1_IE BIT(2) ++ ++/* UNICAM_CMP[0,1] register */ ++#define UNICAM_PCE BIT(31) ++#define UNICAM_GI BIT(9) ++#define UNICAM_CPH BIT(8) ++#define UNICAM_PCVC_MASK GENMASK(7, 6) ++#define UNICAM_PCDT_MASK GENMASK(5, 0) ++ ++/* UNICAM_MISC register */ ++#define UNICAM_FL0 BIT(6) ++#define UNICAM_FL1 BIT(9) ++ ++#endif diff --git a/target/linux/bcm27xx/patches-5.10/950-0265-media-bcm2835-unicam-Add-support-for-get_mbus_config.patch b/target/linux/bcm27xx/patches-5.10/950-0265-media-bcm2835-unicam-Add-support-for-get_mbus_config.patch new file mode 100644 index 0000000000..7d871240a2 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0265-media-bcm2835-unicam-Add-support-for-get_mbus_config.patch @@ -0,0 +1,56 @@ +From 80a9aa25edc6144c3d6d3aaf9f731240d8868714 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 23 Jun 2020 14:32:51 +0100 +Subject: [PATCH] media: bcm2835-unicam: Add support for + get_mbus_config to set num lanes + +Use the get_mbus_config pad subdev call to allow a source to use +fewer than the number of CSI2 lanes defined in device tree. + +Signed-off-by: Dave Stevenson +--- + .../media/platform/bcm2835/bcm2835-unicam.c | 31 ++++++++++++++++--- + 1 file changed, 27 insertions(+), 4 deletions(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -1639,12 +1639,35 @@ static int unicam_start_streaming(struct + goto err_streaming; + } + +- /* +- * TODO: Retrieve the number of active data lanes from the connected +- * subdevice. +- */ + dev->active_data_lanes = dev->max_data_lanes; + ++ if (dev->bus_type == V4L2_MBUS_CSI2_DPHY) { ++ struct v4l2_mbus_config mbus_config = { 0 }; ++ ++ ret = v4l2_subdev_call(dev->sensor, pad, get_mbus_config, ++ 0, &mbus_config); ++ if (ret < 0 && ret != -ENOIOCTLCMD) { ++ unicam_dbg(3, dev, "g_mbus_config failed\n"); ++ goto err_pm_put; ++ } ++ ++ dev->active_data_lanes = ++ (mbus_config.flags & V4L2_MBUS_CSI2_LANE_MASK) >> ++ __ffs(V4L2_MBUS_CSI2_LANE_MASK); ++ if (!dev->active_data_lanes) ++ dev->active_data_lanes = dev->max_data_lanes; ++ if (dev->active_data_lanes > dev->max_data_lanes) { ++ unicam_err(dev, "Device has requested %u data lanes, which is >%u configured in DT\n", ++ dev->active_data_lanes, ++ dev->max_data_lanes); ++ ret = -EINVAL; ++ goto err_pm_put; ++ } ++ } ++ ++ unicam_dbg(1, dev, "Running with %u data lanes\n", ++ dev->active_data_lanes); ++ + ret = clk_set_rate(dev->clock, 100 * 1000 * 1000); + if (ret) { + unicam_err(dev, "failed to set up clock\n"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0266-media-bcm2835-unicam-Avoid-gcc-warning-over-0-on-end.patch b/target/linux/bcm27xx/patches-5.10/950-0266-media-bcm2835-unicam-Avoid-gcc-warning-over-0-on-end.patch new file mode 100644 index 0000000000..1980fda68d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0266-media-bcm2835-unicam-Avoid-gcc-warning-over-0-on-end.patch @@ -0,0 +1,27 @@ +From 03a0144820fa1e5b832b8086a82d99b37b7152a1 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Fri, 26 Jun 2020 15:53:44 +0100 +Subject: [PATCH] media: bcm2835-unicam: Avoid gcc warning over {0} on + endpoint + +Older gcc versions object to = { 0 } initialisation if the first +elemtn in the structure is a substructure. + +Use = { } to avoid this compiler warning. + +Signed-off-by: Dave Stevenson +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -2586,7 +2586,7 @@ static const struct v4l2_async_notifier_ + static int of_unicam_connect_subdevs(struct unicam_device *dev) + { + struct platform_device *pdev = dev->pdev; +- struct v4l2_fwnode_endpoint ep = { 0 }; ++ struct v4l2_fwnode_endpoint ep = { }; + struct device_node *ep_node; + struct device_node *sensor_node; + unsigned int lane; diff --git a/target/linux/bcm27xx/patches-5.10/950-0267-media-i2c-imx290-set-the-format-before-VIDIOC_SUBDEV.patch b/target/linux/bcm27xx/patches-5.10/950-0267-media-i2c-imx290-set-the-format-before-VIDIOC_SUBDEV.patch new file mode 100644 index 0000000000..741d9be947 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0267-media-i2c-imx290-set-the-format-before-VIDIOC_SUBDEV.patch @@ -0,0 +1,40 @@ +From 79d340a54b121610b1d2c5061e8fd1991c6bb1ab Mon Sep 17 00:00:00 2001 +From: Andrey Konovalov +Date: Fri, 12 Jun 2020 15:53:46 +0200 +Subject: [PATCH] media: i2c: imx290: set the format before + VIDIOC_SUBDEV_G_FMT is called + +Commit d46cfdc86c30d5ec768924f0b1e2683c8d20b671 upstream. + +With the current driver 'media-ctl -p' issued right after the imx290 driver +is loaded prints: +pad0: Source + [fmt:unknown/0x0] + +The format value of zero is due to the current_format field of the imx290 +struct not being initialized yet. + +As imx290_entity_init_cfg() calls imx290_set_fmt(), the current_mode field +is also initialized, so the line which set current_mode to a default value +in driver's probe() function is no longer needed. + +Signed-off-by: Andrey Konovalov +Reviewed-by: Manivannan Sadhasivam +Signed-off-by: Sakari Ailus +Signed-off-by: Mauro Carvalho Chehab +--- + drivers/media/i2c/imx290.c | 3 +++ + 1 file changed, 3 insertions(+) + +--- a/drivers/media/i2c/imx290.c ++++ b/drivers/media/i2c/imx290.c +@@ -1091,6 +1091,9 @@ static int imx290_probe(struct i2c_clien + goto free_ctrl; + } + ++ /* Initialize the frame format (this also sets imx290->current_mode) */ ++ imx290_entity_init_cfg(&imx290->sd, NULL); ++ + ret = v4l2_async_register_subdev(&imx290->sd); + if (ret < 0) { + dev_err(dev, "Could not register v4l2 device\n"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0268-media-i2c-imx290-Add-support-for-74.25MHz-clock.patch b/target/linux/bcm27xx/patches-5.10/950-0268-media-i2c-imx290-Add-support-for-74.25MHz-clock.patch new file mode 100644 index 0000000000..04fd46ccee --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0268-media-i2c-imx290-Add-support-for-74.25MHz-clock.patch @@ -0,0 +1,264 @@ +From 4af1d6fb5bdf21e25a0e3819eb1184d33c4b192e Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 25 Jun 2020 08:28:51 +0100 +Subject: [PATCH] media: i2c: imx290: Add support for 74.25MHz clock + +The existing driver only supported a clock of 37.125MHz, but the +sensor also supports 74.25MHz. + +Add the relevant register modifications to support this alternate +clock frequency. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/imx290.c | 119 ++++++++++++++++++++++++++++++------- + 1 file changed, 97 insertions(+), 22 deletions(-) + +--- a/drivers/media/i2c/imx290.c ++++ b/drivers/media/i2c/imx290.c +@@ -1,6 +1,10 @@ + // SPDX-License-Identifier: GPL-2.0 + /* +- * Sony IMX290 CMOS Image Sensor Driver ++ * Sony IMX290/327 CMOS Image Sensor Driver ++ * ++ * The IMX290 and IMX327 are very similar 1920x1080 1/2.8 CMOS image sensors. ++ * IMX327 can support up to 60fps, whilst IMX290 support up to 120fps (only ++ * 10bit and when connected over 4 CSI-2 lanes). + * + * Copyright (C) 2019 FRAMOS GmbH. + * +@@ -22,6 +26,11 @@ + #include + #include + ++enum imx290_clk_index { ++ CLK_37_125, ++ CLK_74_25, ++}; ++ + #define IMX290_STANDBY 0x3000 + #define IMX290_REGHOLD 0x3001 + #define IMX290_XMSTA 0x3002 +@@ -60,11 +69,16 @@ struct imx290_mode { + + const struct imx290_regval *data; + u32 data_size; ++ ++ /* Clock setup can vary. Index as enum imx290_clk_index */ ++ const struct imx290_regval *clk_data[2]; ++ u32 clk_size; + }; + + struct imx290 { + struct device *dev; + struct clk *xclk; ++ u32 xclk_freq; + struct regmap *regmap; + u8 nlanes; + u8 bpp; +@@ -116,8 +130,6 @@ static const struct imx290_regval imx290 + { 0x3018, 0x65 }, + { 0x3019, 0x04 }, + { 0x301a, 0x00 }, +- { 0x3444, 0x20 }, +- { 0x3445, 0x25 }, + { 0x303a, 0x0c }, + { 0x3040, 0x00 }, + { 0x3041, 0x00 }, +@@ -171,6 +183,30 @@ static const struct imx290_regval imx290 + { 0x33b3, 0x04 }, + }; + ++static const struct imx290_regval imx290_37_125mhz_clock_1080p[] = { ++ { 0x305c, 0x18 }, ++ { 0x305d, 0x03 }, ++ { 0x305e, 0x20 }, ++ { 0x305f, 0x01 }, ++ { 0x315e, 0x1a }, ++ { 0x3164, 0x1a }, ++ { 0x3444, 0x20 }, ++ { 0x3445, 0x25 }, ++ { 0x3480, 0x49 }, ++}; ++ ++static const struct imx290_regval imx290_74_250mhz_clock_1080p[] = { ++ { 0x305c, 0x0c }, ++ { 0x305d, 0x03 }, ++ { 0x305e, 0x10 }, ++ { 0x305f, 0x01 }, ++ { 0x315e, 0x1b }, ++ { 0x3164, 0x1b }, ++ { 0x3444, 0x40 }, ++ { 0x3445, 0x4a }, ++ { 0x3480, 0x92 }, ++}; ++ + static const struct imx290_regval imx290_1080p_settings[] = { + /* mode settings */ + { 0x3007, 0x00 }, +@@ -182,13 +218,6 @@ static const struct imx290_regval imx290 + { 0x3419, 0x04 }, + { 0x3012, 0x64 }, + { 0x3013, 0x00 }, +- { 0x305c, 0x18 }, +- { 0x305d, 0x03 }, +- { 0x305e, 0x20 }, +- { 0x305f, 0x01 }, +- { 0x315e, 0x1a }, +- { 0x3164, 0x1a }, +- { 0x3480, 0x49 }, + /* data rate settings */ + { 0x3405, 0x10 }, + { 0x3446, 0x57 }, +@@ -209,6 +238,30 @@ static const struct imx290_regval imx290 + { 0x3455, 0x00 }, + }; + ++static const struct imx290_regval imx290_37_125mhz_clock_720p[] = { ++ { 0x305c, 0x20 }, ++ { 0x305d, 0x00 }, ++ { 0x305e, 0x20 }, ++ { 0x305f, 0x01 }, ++ { 0x315e, 0x1a }, ++ { 0x3164, 0x1a }, ++ { 0x3444, 0x20 }, ++ { 0x3445, 0x25 }, ++ { 0x3480, 0x49 }, ++}; ++ ++static const struct imx290_regval imx290_74_250mhz_clock_720p[] = { ++ { 0x305c, 0x10 }, ++ { 0x305d, 0x00 }, ++ { 0x305e, 0x10 }, ++ { 0x305f, 0x01 }, ++ { 0x315e, 0x1b }, ++ { 0x3164, 0x1b }, ++ { 0x3444, 0x40 }, ++ { 0x3445, 0x4a }, ++ { 0x3480, 0x92 }, ++}; ++ + static const struct imx290_regval imx290_720p_settings[] = { + /* mode settings */ + { 0x3007, 0x10 }, +@@ -220,13 +273,6 @@ static const struct imx290_regval imx290 + { 0x3419, 0x02 }, + { 0x3012, 0x64 }, + { 0x3013, 0x00 }, +- { 0x305c, 0x20 }, +- { 0x305d, 0x00 }, +- { 0x305e, 0x20 }, +- { 0x305f, 0x01 }, +- { 0x315e, 0x1a }, +- { 0x3164, 0x1a }, +- { 0x3480, 0x49 }, + /* data rate settings */ + { 0x3405, 0x10 }, + { 0x3446, 0x4f }, +@@ -312,6 +358,11 @@ static const struct imx290_mode imx290_m + .link_freq_index = FREQ_INDEX_1080P, + .data = imx290_1080p_settings, + .data_size = ARRAY_SIZE(imx290_1080p_settings), ++ .clk_data = { ++ [CLK_37_125] = imx290_37_125mhz_clock_1080p, ++ [CLK_74_25] = imx290_74_250mhz_clock_1080p, ++ }, ++ .clk_size = ARRAY_SIZE(imx290_37_125mhz_clock_1080p), + }, + { + .width = 1280, +@@ -320,6 +371,11 @@ static const struct imx290_mode imx290_m + .link_freq_index = FREQ_INDEX_720P, + .data = imx290_720p_settings, + .data_size = ARRAY_SIZE(imx290_720p_settings), ++ .clk_data = { ++ [CLK_37_125] = imx290_37_125mhz_clock_1080p, ++ [CLK_74_25] = imx290_74_250mhz_clock_1080p, ++ }, ++ .clk_size = ARRAY_SIZE(imx290_37_125mhz_clock_1080p), + }, + }; + +@@ -331,6 +387,11 @@ static const struct imx290_mode imx290_m + .link_freq_index = FREQ_INDEX_1080P, + .data = imx290_1080p_settings, + .data_size = ARRAY_SIZE(imx290_1080p_settings), ++ .clk_data = { ++ [CLK_37_125] = imx290_37_125mhz_clock_720p, ++ [CLK_74_25] = imx290_74_250mhz_clock_720p, ++ }, ++ .clk_size = ARRAY_SIZE(imx290_37_125mhz_clock_720p), + }, + { + .width = 1280, +@@ -339,6 +400,11 @@ static const struct imx290_mode imx290_m + .link_freq_index = FREQ_INDEX_720P, + .data = imx290_720p_settings, + .data_size = ARRAY_SIZE(imx290_720p_settings), ++ .clk_data = { ++ [CLK_37_125] = imx290_37_125mhz_clock_720p, ++ [CLK_74_25] = imx290_74_250mhz_clock_720p, ++ }, ++ .clk_size = ARRAY_SIZE(imx290_37_125mhz_clock_720p), + }, + }; + +@@ -712,6 +778,8 @@ static int imx290_set_hmax(struct imx290 + /* Start streaming */ + static int imx290_start_streaming(struct imx290 *imx290) + { ++ enum imx290_clk_index clk_idx = imx290->xclk_freq == 37125000 ? ++ CLK_37_125 : CLK_74_25; + int ret; + + /* Set init register settings */ +@@ -723,6 +791,14 @@ static int imx290_start_streaming(struct + return ret; + } + ++ ret = imx290_set_register_array(imx290, ++ imx290->current_mode->clk_data[clk_idx], ++ imx290->current_mode->clk_size); ++ if (ret < 0) { ++ dev_err(imx290->dev, "Could not set clock registers\n"); ++ return ret; ++ } ++ + /* Apply the register values related to current frame format */ + ret = imx290_write_current_format(imx290); + if (ret < 0) { +@@ -939,7 +1015,6 @@ static int imx290_probe(struct i2c_clien + .bus_type = V4L2_MBUS_CSI2_DPHY + }; + struct imx290 *imx290; +- u32 xclk_freq; + s64 fq; + int ret; + +@@ -1003,21 +1078,21 @@ static int imx290_probe(struct i2c_clien + } + + ret = fwnode_property_read_u32(dev_fwnode(dev), "clock-frequency", +- &xclk_freq); ++ &imx290->xclk_freq); + if (ret) { + dev_err(dev, "Could not get xclk frequency\n"); + goto free_err; + } + + /* external clock must be 37.125 MHz */ +- if (xclk_freq != 37125000) { ++ if (imx290->xclk_freq != 37125000 && imx290->xclk_freq != 74250000) { + dev_err(dev, "External clock frequency %u is not supported\n", +- xclk_freq); ++ imx290->xclk_freq); + ret = -EINVAL; + goto free_err; + } + +- ret = clk_set_rate(imx290->xclk, xclk_freq); ++ ret = clk_set_rate(imx290->xclk, imx290->xclk_freq); + if (ret) { + dev_err(dev, "Could not set xclk frequency\n"); + goto free_err; diff --git a/target/linux/bcm27xx/patches-5.10/950-0269-media-i2c-imx290-Correct-range-for-V4L2_CID_GAIN-to-.patch b/target/linux/bcm27xx/patches-5.10/950-0269-media-i2c-imx290-Correct-range-for-V4L2_CID_GAIN-to-.patch new file mode 100644 index 0000000000..3674f1ecde --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0269-media-i2c-imx290-Correct-range-for-V4L2_CID_GAIN-to-.patch @@ -0,0 +1,26 @@ +From 5b95bb7b2d6b1a866c3ddd752bdbcfa09b0657b0 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 11 Jun 2020 13:41:43 +0100 +Subject: [PATCH] media: i2c: imx290: Correct range for V4L2_CID_GAIN + to 0-238 + +The datasheet lists the gain as being 0.0 to 72.0dB in 0.3dB steps, which +makes 238 steps total. +Correct the 0-72 range defined in the driver. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/imx290.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/media/i2c/imx290.c ++++ b/drivers/media/i2c/imx290.c +@@ -1124,7 +1124,7 @@ static int imx290_probe(struct i2c_clien + v4l2_ctrl_handler_init(&imx290->ctrls, 4); + + v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops, +- V4L2_CID_GAIN, 0, 72, 1, 0); ++ V4L2_CID_GAIN, 0, 238, 1, 0); + + imx290->link_freq = + v4l2_ctrl_new_int_menu(&imx290->ctrls, &imx290_ctrl_ops, diff --git a/target/linux/bcm27xx/patches-5.10/950-0270-media-i2c-imx290-Convert-HMAX-setting-into-V4L2_CID_.patch b/target/linux/bcm27xx/patches-5.10/950-0270-media-i2c-imx290-Convert-HMAX-setting-into-V4L2_CID_.patch new file mode 100644 index 0000000000..609ca7fe31 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0270-media-i2c-imx290-Convert-HMAX-setting-into-V4L2_CID_.patch @@ -0,0 +1,159 @@ +From a3359aca41e5942a74f803ce8837ef24456db2d5 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 11 Jun 2020 14:36:40 +0100 +Subject: [PATCH] media: i2c: imx290: Convert HMAX setting into + V4L2_CID_HBLANK + +Userspace needs to know HBLANK if it is to work out exposure times +and frame rates, therefore convert it to map onto V4L2_CID_HBLANK + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/imx290.c | 66 +++++++++++++++++++++++++------------- + 1 file changed, 44 insertions(+), 22 deletions(-) + +--- a/drivers/media/i2c/imx290.c ++++ b/drivers/media/i2c/imx290.c +@@ -40,6 +40,9 @@ enum imx290_clk_index { + #define IMX290_GAIN 0x3014 + #define IMX290_HMAX_LOW 0x301c + #define IMX290_HMAX_HIGH 0x301d ++#define IMX290_HMAX_MIN_2LANE 4400 /* Min of 4400 pixels = 30fps */ ++#define IMX290_HMAX_MIN_4LANE 2200 /* Min of 2200 pixels = 60fps */ ++#define IMX290_HMAX_MAX 0xffff + #define IMX290_PGCTRL 0x308c + #define IMX290_PHY_LANE_NUM 0x3407 + #define IMX290_CSI_LANE_MODE 0x3443 +@@ -82,6 +85,7 @@ struct imx290 { + struct regmap *regmap; + u8 nlanes; + u8 bpp; ++ u16 hmax_min; + + struct v4l2_subdev sd; + struct media_pad pad; +@@ -94,6 +98,7 @@ struct imx290 { + struct v4l2_ctrl_handler ctrls; + struct v4l2_ctrl *link_freq; + struct v4l2_ctrl *pixel_rate; ++ struct v4l2_ctrl *hblank; + + struct mutex lock; + }; +@@ -518,6 +523,26 @@ static int imx290_set_gain(struct imx290 + return ret; + } + ++static int imx290_set_hmax(struct imx290 *imx290, u32 val) ++{ ++ u32 hmax = val + imx290->current_mode->width; ++ int ret; ++ ++ ret = imx290_write_reg(imx290, IMX290_HMAX_LOW, (hmax & 0xff)); ++ if (ret) { ++ dev_err(imx290->dev, "Error setting HMAX register\n"); ++ return ret; ++ } ++ ++ ret = imx290_write_reg(imx290, IMX290_HMAX_HIGH, ((hmax >> 8) & 0xff)); ++ if (ret) { ++ dev_err(imx290->dev, "Error setting HMAX register\n"); ++ return ret; ++ } ++ ++ return 0; ++} ++ + /* Stop streaming */ + static int imx290_stop_streaming(struct imx290 *imx290) + { +@@ -546,6 +571,9 @@ static int imx290_set_ctrl(struct v4l2_c + case V4L2_CID_GAIN: + ret = imx290_set_gain(imx290, ctrl->val); + break; ++ case V4L2_CID_HBLANK: ++ ret = imx290_set_hmax(imx290, ctrl->val); ++ break; + case V4L2_CID_TEST_PATTERN: + if (ctrl->val) { + imx290_write_reg(imx290, IMX290_BLKLEVEL_LOW, 0x00); +@@ -702,6 +730,12 @@ static int imx290_set_fmt(struct v4l2_su + if (imx290->pixel_rate) + __v4l2_ctrl_s_ctrl_int64(imx290->pixel_rate, + imx290_calc_pixel_rate(imx290)); ++ ++ if (imx290->hblank) ++ __v4l2_ctrl_modify_range(imx290->hblank, ++ imx290->hmax_min - mode->width, ++ IMX290_HMAX_MAX - mode->width, ++ 1, mode->hmax - mode->width); + } + + *format = fmt->format; +@@ -756,25 +790,6 @@ static int imx290_write_current_format(s + return 0; + } + +-static int imx290_set_hmax(struct imx290 *imx290, u32 val) +-{ +- int ret; +- +- ret = imx290_write_reg(imx290, IMX290_HMAX_LOW, (val & 0xff)); +- if (ret) { +- dev_err(imx290->dev, "Error setting HMAX register\n"); +- return ret; +- } +- +- ret = imx290_write_reg(imx290, IMX290_HMAX_HIGH, ((val >> 8) & 0xff)); +- if (ret) { +- dev_err(imx290->dev, "Error setting HMAX register\n"); +- return ret; +- } +- +- return 0; +-} +- + /* Start streaming */ + static int imx290_start_streaming(struct imx290 *imx290) + { +@@ -813,9 +828,6 @@ static int imx290_start_streaming(struct + dev_err(imx290->dev, "Could not set current mode\n"); + return ret; + } +- ret = imx290_set_hmax(imx290, imx290->current_mode->hmax); +- if (ret < 0) +- return ret; + + /* Apply customized values from user */ + ret = v4l2_ctrl_handler_setup(imx290->sd.ctrl_handler); +@@ -1014,6 +1026,7 @@ static int imx290_probe(struct i2c_clien + struct v4l2_fwnode_endpoint ep = { + .bus_type = V4L2_MBUS_CSI2_DPHY + }; ++ const struct imx290_mode *mode; + struct imx290 *imx290; + s64 fq; + int ret; +@@ -1052,6 +1065,8 @@ static int imx290_probe(struct i2c_clien + ret = -EINVAL; + goto free_err; + } ++ imx290->hmax_min = (imx290->nlanes == 2) ? IMX290_HMAX_MIN_2LANE : ++ IMX290_HMAX_MIN_4LANE; + + dev_dbg(dev, "Using %u data lanes\n", imx290->nlanes); + +@@ -1126,6 +1141,13 @@ static int imx290_probe(struct i2c_clien + v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops, + V4L2_CID_GAIN, 0, 238, 1, 0); + ++ mode = imx290->current_mode; ++ imx290->hblank = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops, ++ V4L2_CID_HBLANK, ++ imx290->hmax_min - mode->width, ++ IMX290_HMAX_MAX - mode->width, 1, ++ mode->hmax - mode->width); ++ + imx290->link_freq = + v4l2_ctrl_new_int_menu(&imx290->ctrls, &imx290_ctrl_ops, + V4L2_CID_LINK_FREQ, diff --git a/target/linux/bcm27xx/patches-5.10/950-0271-media-i2c-imx290-Add-support-for-V4L2_CID_VBLANK.patch b/target/linux/bcm27xx/patches-5.10/950-0271-media-i2c-imx290-Add-support-for-V4L2_CID_VBLANK.patch new file mode 100644 index 0000000000..fe9f9808e2 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0271-media-i2c-imx290-Add-support-for-V4L2_CID_VBLANK.patch @@ -0,0 +1,141 @@ +From e8ad74c090f54cf8ce845b627e4312b6166059fd Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 11 Jun 2020 18:09:12 +0100 +Subject: [PATCH] media: i2c: imx290: Add support for V4L2_CID_VBLANK + +In order to calculate framerate and durations userspace needs +the vertical blanking information. This can be configurable, +and indeed the datasheet lists different values for VBLANK for +the 1080p and 720p modes. + +Add the new control, and adopt the datasheet values for each mode. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/imx290.c | 38 ++++++++++++++++++++++++++++++++++++-- + 1 file changed, 36 insertions(+), 2 deletions(-) + +--- a/drivers/media/i2c/imx290.c ++++ b/drivers/media/i2c/imx290.c +@@ -38,6 +38,8 @@ enum imx290_clk_index { + #define IMX290_BLKLEVEL_LOW 0x300a + #define IMX290_BLKLEVEL_HIGH 0x300b + #define IMX290_GAIN 0x3014 ++#define IMX290_VMAX_LOW 0x3018 ++#define IMX290_VMAX_MAX 0x3fff + #define IMX290_HMAX_LOW 0x301c + #define IMX290_HMAX_HIGH 0x301d + #define IMX290_HMAX_MIN_2LANE 4400 /* Min of 4400 pixels = 30fps */ +@@ -68,6 +70,7 @@ struct imx290_mode { + u32 width; + u32 height; + u32 hmax; ++ u32 vmax; + u8 link_freq_index; + + const struct imx290_regval *data; +@@ -99,6 +102,7 @@ struct imx290 { + struct v4l2_ctrl *link_freq; + struct v4l2_ctrl *pixel_rate; + struct v4l2_ctrl *hblank; ++ struct v4l2_ctrl *vblank; + + struct mutex lock; + }; +@@ -132,8 +136,6 @@ static const char * const imx290_test_pa + + static const struct imx290_regval imx290_global_init_settings[] = { + { 0x3007, 0x00 }, +- { 0x3018, 0x65 }, +- { 0x3019, 0x04 }, + { 0x301a, 0x00 }, + { 0x303a, 0x0c }, + { 0x3040, 0x00 }, +@@ -360,6 +362,7 @@ static const struct imx290_mode imx290_m + .width = 1920, + .height = 1080, + .hmax = 0x1130, ++ .vmax = 0x0465, + .link_freq_index = FREQ_INDEX_1080P, + .data = imx290_1080p_settings, + .data_size = ARRAY_SIZE(imx290_1080p_settings), +@@ -373,6 +376,7 @@ static const struct imx290_mode imx290_m + .width = 1280, + .height = 720, + .hmax = 0x19c8, ++ .vmax = 0x02ee, + .link_freq_index = FREQ_INDEX_720P, + .data = imx290_720p_settings, + .data_size = ARRAY_SIZE(imx290_720p_settings), +@@ -389,6 +393,7 @@ static const struct imx290_mode imx290_m + .width = 1920, + .height = 1080, + .hmax = 0x0898, ++ .vmax = 0x0465, + .link_freq_index = FREQ_INDEX_1080P, + .data = imx290_1080p_settings, + .data_size = ARRAY_SIZE(imx290_1080p_settings), +@@ -402,6 +407,7 @@ static const struct imx290_mode imx290_m + .width = 1280, + .height = 720, + .hmax = 0x0ce4, ++ .vmax = 0x02ee, + .link_freq_index = FREQ_INDEX_720P, + .data = imx290_720p_settings, + .data_size = ARRAY_SIZE(imx290_720p_settings), +@@ -543,6 +549,19 @@ static int imx290_set_hmax(struct imx290 + return 0; + } + ++static int imx290_set_vmax(struct imx290 *imx290, u32 val) ++{ ++ u32 vmax = val + imx290->current_mode->height; ++ int ret; ++ ++ ret = imx290_write_buffered_reg(imx290, IMX290_VMAX_LOW, 3, ++ vmax); ++ if (ret) ++ dev_err(imx290->dev, "Unable to write vmax\n"); ++ ++ return ret; ++} ++ + /* Stop streaming */ + static int imx290_stop_streaming(struct imx290 *imx290) + { +@@ -574,6 +593,9 @@ static int imx290_set_ctrl(struct v4l2_c + case V4L2_CID_HBLANK: + ret = imx290_set_hmax(imx290, ctrl->val); + break; ++ case V4L2_CID_VBLANK: ++ ret = imx290_set_vmax(imx290, ctrl->val); ++ break; + case V4L2_CID_TEST_PATTERN: + if (ctrl->val) { + imx290_write_reg(imx290, IMX290_BLKLEVEL_LOW, 0x00); +@@ -736,6 +758,12 @@ static int imx290_set_fmt(struct v4l2_su + imx290->hmax_min - mode->width, + IMX290_HMAX_MAX - mode->width, + 1, mode->hmax - mode->width); ++ if (imx290->vblank) ++ __v4l2_ctrl_modify_range(imx290->vblank, ++ mode->vmax - mode->height, ++ IMX290_VMAX_MAX - mode->height, ++ 1, ++ mode->vmax - mode->height); + } + + *format = fmt->format; +@@ -1148,6 +1176,12 @@ static int imx290_probe(struct i2c_clien + IMX290_HMAX_MAX - mode->width, 1, + mode->hmax - mode->width); + ++ imx290->vblank = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops, ++ V4L2_CID_VBLANK, ++ mode->vmax - mode->height, ++ IMX290_VMAX_MAX - mode->height, 1, ++ mode->vmax - mode->height); ++ + imx290->link_freq = + v4l2_ctrl_new_int_menu(&imx290->ctrls, &imx290_ctrl_ops, + V4L2_CID_LINK_FREQ, diff --git a/target/linux/bcm27xx/patches-5.10/950-0272-media-i2c-imx290-Add-exposure-control-to-the-driver.patch b/target/linux/bcm27xx/patches-5.10/950-0272-media-i2c-imx290-Add-exposure-control-to-the-driver.patch new file mode 100644 index 0000000000..0865830752 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0272-media-i2c-imx290-Add-exposure-control-to-the-driver.patch @@ -0,0 +1,93 @@ +From 3802436037a2df9a85eee1e2917521c02e2263b7 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 11 Jun 2020 18:19:13 +0100 +Subject: [PATCH] media: i2c: imx290: Add exposure control to the + driver. + +Adds support for V4L2_CID_EXPOSURE so that userspace can control +the sensor exposure time. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/imx290.c | 35 +++++++++++++++++++++++++++++++++++ + 1 file changed, 35 insertions(+) + +--- a/drivers/media/i2c/imx290.c ++++ b/drivers/media/i2c/imx290.c +@@ -45,6 +45,10 @@ enum imx290_clk_index { + #define IMX290_HMAX_MIN_2LANE 4400 /* Min of 4400 pixels = 30fps */ + #define IMX290_HMAX_MIN_4LANE 2200 /* Min of 2200 pixels = 60fps */ + #define IMX290_HMAX_MAX 0xffff ++ ++#define IMX290_EXPOSURE_MIN 2 ++#define IMX290_EXPOSURE_STEP 1 ++#define IMX290_EXPOSURE_LOW 0x3020 + #define IMX290_PGCTRL 0x308c + #define IMX290_PHY_LANE_NUM 0x3407 + #define IMX290_CSI_LANE_MODE 0x3443 +@@ -103,6 +107,7 @@ struct imx290 { + struct v4l2_ctrl *pixel_rate; + struct v4l2_ctrl *hblank; + struct v4l2_ctrl *vblank; ++ struct v4l2_ctrl *exposure; + + struct mutex lock; + }; +@@ -529,6 +534,20 @@ static int imx290_set_gain(struct imx290 + return ret; + } + ++static int imx290_set_exposure(struct imx290 *imx290, u32 value) ++{ ++ u32 exposure = (imx290->current_mode->height + imx290->vblank->val) - ++ value; ++ int ret; ++ ++ ret = imx290_write_buffered_reg(imx290, IMX290_EXPOSURE_LOW, 3, ++ exposure); ++ if (ret) ++ dev_err(imx290->dev, "Unable to write exposure\n"); ++ ++ return ret; ++} ++ + static int imx290_set_hmax(struct imx290 *imx290, u32 val) + { + u32 hmax = val + imx290->current_mode->width; +@@ -590,6 +609,9 @@ static int imx290_set_ctrl(struct v4l2_c + case V4L2_CID_GAIN: + ret = imx290_set_gain(imx290, ctrl->val); + break; ++ case V4L2_CID_EXPOSURE: ++ ret = imx290_set_exposure(imx290, ctrl->val); ++ break; + case V4L2_CID_HBLANK: + ret = imx290_set_hmax(imx290, ctrl->val); + break; +@@ -764,6 +786,12 @@ static int imx290_set_fmt(struct v4l2_su + IMX290_VMAX_MAX - mode->height, + 1, + mode->vmax - mode->height); ++ if (imx290->exposure) ++ __v4l2_ctrl_modify_range(imx290->exposure, ++ mode->vmax - mode->height, ++ mode->vmax - 4, ++ IMX290_EXPOSURE_STEP, ++ mode->vmax - 4); + } + + *format = fmt->format; +@@ -1182,6 +1210,13 @@ static int imx290_probe(struct i2c_clien + IMX290_VMAX_MAX - mode->height, 1, + mode->vmax - mode->height); + ++ imx290->exposure = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops, ++ V4L2_CID_EXPOSURE, ++ IMX290_EXPOSURE_MIN, ++ mode->vmax - 4, ++ IMX290_EXPOSURE_STEP, ++ mode->vmax - 4); ++ + imx290->link_freq = + v4l2_ctrl_new_int_menu(&imx290->ctrls, &imx290_ctrl_ops, + V4L2_CID_LINK_FREQ, diff --git a/target/linux/bcm27xx/patches-5.10/950-0273-media-i2c-imx290-Add-H-and-V-flip-controls.patch b/target/linux/bcm27xx/patches-5.10/950-0273-media-i2c-imx290-Add-H-and-V-flip-controls.patch new file mode 100644 index 0000000000..0ad9193d6d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0273-media-i2c-imx290-Add-H-and-V-flip-controls.patch @@ -0,0 +1,83 @@ +From ab78051da1ad984c5b424c1e75f487d2a2f2c026 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 11 Jun 2020 18:34:16 +0100 +Subject: [PATCH] media: i2c: imx290: Add H and V flip controls + +The sensor supports horizontal and vertical flips, so support them +through V4L2_CID_HFLIP and V4L2_CID_VFLIP. + +This sensor does NOT change the Bayer order when changing the +direction of readout, therefore no special handling is required for +that. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/imx290.c | 22 ++++++++++++++++++++++ + 1 file changed, 22 insertions(+) + +--- a/drivers/media/i2c/imx290.c ++++ b/drivers/media/i2c/imx290.c +@@ -34,6 +34,7 @@ enum imx290_clk_index { + #define IMX290_STANDBY 0x3000 + #define IMX290_REGHOLD 0x3001 + #define IMX290_XMSTA 0x3002 ++#define IMX290_FLIP_WINMODE 0x3007 + #define IMX290_FR_FDG_SEL 0x3009 + #define IMX290_BLKLEVEL_LOW 0x300a + #define IMX290_BLKLEVEL_HIGH 0x300b +@@ -107,6 +108,8 @@ struct imx290 { + struct v4l2_ctrl *pixel_rate; + struct v4l2_ctrl *hblank; + struct v4l2_ctrl *vblank; ++ struct v4l2_ctrl *hflip; ++ struct v4l2_ctrl *vflip; + struct v4l2_ctrl *exposure; + + struct mutex lock; +@@ -600,6 +603,7 @@ static int imx290_set_ctrl(struct v4l2_c + struct imx290 *imx290 = container_of(ctrl->handler, + struct imx290, ctrls); + int ret = 0; ++ u8 val; + + /* V4L2 controls values will be applied only when power is already up */ + if (!pm_runtime_get_if_in_use(imx290->dev)) +@@ -618,6 +622,16 @@ static int imx290_set_ctrl(struct v4l2_c + case V4L2_CID_VBLANK: + ret = imx290_set_vmax(imx290, ctrl->val); + break; ++ case V4L2_CID_HFLIP: ++ case V4L2_CID_VFLIP: ++ /* WINMODE is in bits [6:4], so need to read-modify-write */ ++ ret = imx290_read_reg(imx290, IMX290_FLIP_WINMODE, &val); ++ if (ret) ++ break; ++ val &= ~0x03; ++ val |= imx290->vflip->val | (imx290->hflip->val << 1); ++ ret = imx290_write_reg(imx290, IMX290_FLIP_WINMODE, val); ++ break; + case V4L2_CID_TEST_PATTERN: + if (ctrl->val) { + imx290_write_reg(imx290, IMX290_BLKLEVEL_LOW, 0x00); +@@ -924,6 +938,9 @@ static int imx290_set_stream(struct v4l2 + imx290_stop_streaming(imx290); + pm_runtime_put(imx290->dev); + } ++ /* vflip and hflip cannot change during streaming */ ++ __v4l2_ctrl_grab(imx290->vflip, enable); ++ __v4l2_ctrl_grab(imx290->hflip, enable); + + unlock_and_return: + +@@ -1217,6 +1234,11 @@ static int imx290_probe(struct i2c_clien + IMX290_EXPOSURE_STEP, + mode->vmax - 4); + ++ imx290->hflip = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops, ++ V4L2_CID_HFLIP, 0, 1, 1, 0); ++ imx290->vflip = v4l2_ctrl_new_std(&imx290->ctrls, &imx290_ctrl_ops, ++ V4L2_CID_VFLIP, 0, 1, 1, 0); ++ + imx290->link_freq = + v4l2_ctrl_new_int_menu(&imx290->ctrls, &imx290_ctrl_ops, + V4L2_CID_LINK_FREQ, diff --git a/target/linux/bcm27xx/patches-5.10/950-0274-media-dt-bindings-media-i2c-Add-mono-version-to-IMX2.patch b/target/linux/bcm27xx/patches-5.10/950-0274-media-dt-bindings-media-i2c-Add-mono-version-to-IMX2.patch new file mode 100644 index 0000000000..bc195d9cb3 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0274-media-dt-bindings-media-i2c-Add-mono-version-to-IMX2.patch @@ -0,0 +1,36 @@ +From 5e67752c725fa06d0e2455dac19fbef93e313eb7 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 25 Jun 2020 16:52:14 +0100 +Subject: [PATCH] media: dt-bindings: media: i2c: Add mono version to + IMX290 bindings + +The IMX290 module is available as either monochrome or colour and +the variant is not detectable at runtime. + +Add a new compatible string for the monochrome version. + +Signed-off-by: Dave Stevenson +--- + Documentation/devicetree/bindings/media/i2c/imx290.txt | 7 ++++--- + 1 file changed, 4 insertions(+), 3 deletions(-) + +--- a/Documentation/devicetree/bindings/media/i2c/imx290.txt ++++ b/Documentation/devicetree/bindings/media/i2c/imx290.txt +@@ -1,13 +1,14 @@ + * Sony IMX290 1/2.8-Inch CMOS Image Sensor + + The Sony IMX290 is a 1/2.8-Inch CMOS Solid-state image sensor with +-Square Pixel for Color Cameras. It is programmable through I2C and 4-wire +-interfaces. The sensor output is available via CMOS logic parallel SDR output, ++Square Pixel for Color or Monochrome Cameras. It is programmable through I2C ++and 4-wire interfaces. ++The sensor output is available via CMOS logic parallel SDR output, + Low voltage LVDS DDR output and CSI-2 serial data output. The CSI-2 bus is the + default. No bindings have been defined for the other busses. + + Required Properties: +-- compatible: Should be "sony,imx290" ++- compatible: Should be "sony,imx290", or "sony,imx290-mono" + - reg: I2C bus address of the device + - clocks: Reference to the xclk clock. + - clock-names: Should be "xclk". diff --git a/target/linux/bcm27xx/patches-5.10/950-0275-media-i2c-imx290-Add-support-for-the-mono-sensor-var.patch b/target/linux/bcm27xx/patches-5.10/950-0275-media-i2c-imx290-Add-support-for-the-mono-sensor-var.patch new file mode 100644 index 0000000000..a0f79ef9d1 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0275-media-i2c-imx290-Add-support-for-the-mono-sensor-var.patch @@ -0,0 +1,185 @@ +From 550fc1298f6a4726e3944944561a047b3e04b134 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 25 Jun 2020 17:03:11 +0100 +Subject: [PATCH] media : i2c: imx290: Add support for the mono sensor + variant. + +The IMX290 module is available as either mono or colour (Bayer). + +Update the driver so that it can advertise the correct mono +formats instead of the colour ones. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/imx290.c | 58 +++++++++++++++++++++++++++----------- + 1 file changed, 41 insertions(+), 17 deletions(-) + +--- a/drivers/media/i2c/imx290.c ++++ b/drivers/media/i2c/imx290.c +@@ -1,10 +1,12 @@ + // SPDX-License-Identifier: GPL-2.0 + /* +- * Sony IMX290/327 CMOS Image Sensor Driver ++ * Sony IMX290 & IMX327 CMOS Image Sensor Driver + * + * The IMX290 and IMX327 are very similar 1920x1080 1/2.8 CMOS image sensors. +- * IMX327 can support up to 60fps, whilst IMX290 support up to 120fps (only +- * 10bit and when connected over 4 CSI-2 lanes). ++ * IMX327 can support up to 60fps, whilst IMX290 can support up to 120fps, but ++ * only 10bit and when connected over 4 CSI-2 lanes. ++ * The modules don't appear to have a mechanism to identify whether the mono or ++ * colour variant is connected, therefore it is done via compatible string. + * + * Copyright (C) 2019 FRAMOS GmbH. + * +@@ -17,6 +19,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -95,6 +98,8 @@ struct imx290 { + u8 bpp; + u16 hmax_min; + ++ const struct imx290_pixfmt *formats; ++ + struct v4l2_subdev sd; + struct media_pad pad; + struct v4l2_mbus_framefmt current_format; +@@ -120,11 +125,18 @@ struct imx290_pixfmt { + u8 bpp; + }; + +-static const struct imx290_pixfmt imx290_formats[] = { ++#define IMX290_NUM_FORMATS 2 ++ ++static const struct imx290_pixfmt imx290_colour_formats[IMX290_NUM_FORMATS] = { + { MEDIA_BUS_FMT_SRGGB10_1X10, 10 }, + { MEDIA_BUS_FMT_SRGGB12_1X12, 12 }, + }; + ++static const struct imx290_pixfmt imx290_mono_formats[IMX290_NUM_FORMATS] = { ++ { MEDIA_BUS_FMT_Y10_1X10, 10 }, ++ { MEDIA_BUS_FMT_Y12_1X12, 12 }, ++}; ++ + static const struct regmap_config imx290_regmap_config = { + .reg_bits = 16, + .val_bits = 8, +@@ -671,10 +683,12 @@ static int imx290_enum_mbus_code(struct + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_mbus_code_enum *code) + { +- if (code->index >= ARRAY_SIZE(imx290_formats)) ++ const struct imx290 *imx290 = to_imx290(sd); ++ ++ if (code->index >= IMX290_NUM_FORMATS) + return -EINVAL; + +- code->code = imx290_formats[code->index].code; ++ code->code = imx290->formats[code->index].code; + + return 0; + } +@@ -686,8 +700,8 @@ static int imx290_enum_frame_size(struct + const struct imx290 *imx290 = to_imx290(sd); + const struct imx290_mode *imx290_modes = imx290_modes_ptr(imx290); + +- if ((fse->code != imx290_formats[0].code) && +- (fse->code != imx290_formats[1].code)) ++ if (fse->code != imx290->formats[0].code && ++ fse->code != imx290->formats[1].code) + return -EINVAL; + + if (fse->index >= imx290_modes_num(imx290)) +@@ -765,14 +779,14 @@ static int imx290_set_fmt(struct v4l2_su + fmt->format.width = mode->width; + fmt->format.height = mode->height; + +- for (i = 0; i < ARRAY_SIZE(imx290_formats); i++) +- if (imx290_formats[i].code == fmt->format.code) ++ for (i = 0; i < IMX290_NUM_FORMATS; i++) ++ if (imx290->formats[i].code == fmt->format.code) + break; + +- if (i >= ARRAY_SIZE(imx290_formats)) ++ if (i >= IMX290_NUM_FORMATS) + i = 0; + +- fmt->format.code = imx290_formats[i].code; ++ fmt->format.code = imx290->formats[i].code; + fmt->format.field = V4L2_FIELD_NONE; + + if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { +@@ -780,7 +794,7 @@ static int imx290_set_fmt(struct v4l2_su + } else { + format = &imx290->current_format; + imx290->current_mode = mode; +- imx290->bpp = imx290_formats[i].bpp; ++ imx290->bpp = imx290->formats[i].bpp; + + if (imx290->link_freq) + __v4l2_ctrl_s_ctrl(imx290->link_freq, +@@ -835,6 +849,7 @@ static int imx290_write_current_format(s + + switch (imx290->current_format.code) { + case MEDIA_BUS_FMT_SRGGB10_1X10: ++ case MEDIA_BUS_FMT_Y10_1X10: + ret = imx290_set_register_array(imx290, imx290_10bit_settings, + ARRAY_SIZE( + imx290_10bit_settings)); +@@ -844,6 +859,7 @@ static int imx290_write_current_format(s + } + break; + case MEDIA_BUS_FMT_SRGGB12_1X12: ++ case MEDIA_BUS_FMT_Y12_1X12: + ret = imx290_set_register_array(imx290, imx290_12bit_settings, + ARRAY_SIZE( + imx290_12bit_settings)); +@@ -1091,6 +1107,12 @@ static s64 imx290_check_link_freqs(const + return 0; + } + ++static const struct of_device_id imx290_of_match[] = { ++ { .compatible = "sony,imx290", .data = imx290_colour_formats }, ++ { .compatible = "sony,imx290-mono", .data = imx290_mono_formats }, ++ { /* sentinel */ } ++}; ++ + static int imx290_probe(struct i2c_client *client) + { + struct device *dev = &client->dev; +@@ -1099,6 +1121,7 @@ static int imx290_probe(struct i2c_clien + struct v4l2_fwnode_endpoint ep = { + .bus_type = V4L2_MBUS_CSI2_DPHY + }; ++ const struct of_device_id *match; + const struct imx290_mode *mode; + struct imx290 *imx290; + s64 fq; +@@ -1115,6 +1138,11 @@ static int imx290_probe(struct i2c_clien + return -ENODEV; + } + ++ match = of_match_device(imx290_of_match, dev); ++ if (!match) ++ return -ENODEV; ++ imx290->formats = (const struct imx290_pixfmt *)match->data; ++ + endpoint = fwnode_graph_get_next_endpoint(dev_fwnode(dev), NULL); + if (!endpoint) { + dev_err(dev, "Endpoint node not found\n"); +@@ -1333,10 +1361,6 @@ static int imx290_remove(struct i2c_clie + return 0; + } + +-static const struct of_device_id imx290_of_match[] = { +- { .compatible = "sony,imx290" }, +- { /* sentinel */ } +-}; + MODULE_DEVICE_TABLE(of, imx290_of_match); + + static struct i2c_driver imx290_i2c_driver = { diff --git a/target/linux/bcm27xx/patches-5.10/950-0276-media-i2c-imx290-Switch-set_hmax-to-use-imx290_write.patch b/target/linux/bcm27xx/patches-5.10/950-0276-media-i2c-imx290-Switch-set_hmax-to-use-imx290_write.patch new file mode 100644 index 0000000000..1e6b140802 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0276-media-i2c-imx290-Switch-set_hmax-to-use-imx290_write.patch @@ -0,0 +1,43 @@ +From 4e0e8f87b81ed1dfa9876e0ce4492cc8f64c935a Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Fri, 26 Jun 2020 18:11:49 +0100 +Subject: [PATCH] media: i2c: imx290: Switch set_hmax to use + imx290_write_buffered_reg + +imx290_set_hmax was using two independent writes to set up hmax, +when all other multi-register writes were using imx290_write_buffered_reg +which claims the group hold first. + +Switch imx290_set_hmax to using imx290_write_buffered_reg too. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/imx290.c | 15 ++++----------- + 1 file changed, 4 insertions(+), 11 deletions(-) + +--- a/drivers/media/i2c/imx290.c ++++ b/drivers/media/i2c/imx290.c +@@ -568,19 +568,12 @@ static int imx290_set_hmax(struct imx290 + u32 hmax = val + imx290->current_mode->width; + int ret; + +- ret = imx290_write_reg(imx290, IMX290_HMAX_LOW, (hmax & 0xff)); +- if (ret) { ++ ret = imx290_write_buffered_reg(imx290, IMX290_HMAX_LOW, 2, ++ hmax); ++ if (ret) + dev_err(imx290->dev, "Error setting HMAX register\n"); +- return ret; +- } + +- ret = imx290_write_reg(imx290, IMX290_HMAX_HIGH, ((hmax >> 8) & 0xff)); +- if (ret) { +- dev_err(imx290->dev, "Error setting HMAX register\n"); +- return ret; +- } +- +- return 0; ++ return ret; + } + + static int imx290_set_vmax(struct imx290 *imx290, u32 val) diff --git a/target/linux/bcm27xx/patches-5.10/950-0277-serial-8250-bcm2835aux-defer-if-clock-is-zero.patch b/target/linux/bcm27xx/patches-5.10/950-0277-serial-8250-bcm2835aux-defer-if-clock-is-zero.patch new file mode 100644 index 0000000000..304552f790 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0277-serial-8250-bcm2835aux-defer-if-clock-is-zero.patch @@ -0,0 +1,28 @@ +From e3af8dd4ba4fc1ae6260823dfb3a82236471c353 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Thu, 2 Jul 2020 13:53:20 +0100 +Subject: [PATCH] serial: 8250: bcm2835aux - defer if clock is zero + +See: https://github.com/raspberrypi/linux/issues/3700 + +Signed-off-by: Phil Elwell +--- + drivers/tty/serial/8250/8250_bcm2835aux.c | 7 +++++++ + 1 file changed, 7 insertions(+) + +--- a/drivers/tty/serial/8250/8250_bcm2835aux.c ++++ b/drivers/tty/serial/8250/8250_bcm2835aux.c +@@ -148,6 +148,13 @@ static int bcm2835aux_serial_probe(struc + */ + up.port.uartclk = clk_get_rate(data->clk) * 2; + ++ /* The clock is only queried at probe time, which means we get one shot ++ * at this. A zero clock is never going to work and is almost certainly ++ * due to a parent not being ready, so prefer to defer. ++ */ ++ if (!up.port.uartclk) ++ return -EPROBE_DEFER; ++ + /* register the port */ + ret = serial8250_register_8250_port(&up); + if (ret < 0) { diff --git a/target/linux/bcm27xx/patches-5.10/950-0278-media-Add-a-pixel-format-for-MIPI-packed-12bit-luma-.patch b/target/linux/bcm27xx/patches-5.10/950-0278-media-Add-a-pixel-format-for-MIPI-packed-12bit-luma-.patch new file mode 100644 index 0000000000..fb27792ca3 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0278-media-Add-a-pixel-format-for-MIPI-packed-12bit-luma-.patch @@ -0,0 +1,95 @@ +From 85e4a24a7f8fd96cc765c038bbae601ca69daa39 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 7 May 2020 16:59:03 +0100 +Subject: [PATCH] media: Add a pixel format for MIPI packed 12bit luma + only. + +This is the format used by monochrome 12bit image sensors. + +Signed-off-by: Dave Stevenson +--- + .../userspace-api/media/v4l/pixfmt-y12p.rst | 45 +++++++++++++++++++ + .../userspace-api/media/v4l/yuv-formats.rst | 1 + + drivers/media/v4l2-core/v4l2-ioctl.c | 1 + + include/uapi/linux/videodev2.h | 1 + + 4 files changed, 48 insertions(+) + create mode 100644 Documentation/userspace-api/media/v4l/pixfmt-y12p.rst + +--- /dev/null ++++ b/Documentation/userspace-api/media/v4l/pixfmt-y12p.rst +@@ -0,0 +1,45 @@ ++.. Permission is granted to copy, distribute and/or modify this ++.. document under the terms of the GNU Free Documentation License, ++.. Version 1.1 or any later version published by the Free Software ++.. Foundation, with no Invariant Sections, no Front-Cover Texts ++.. and no Back-Cover Texts. A copy of the license is included at ++.. Documentation/media/uapi/fdl-appendix.rst. ++.. ++.. TODO: replace it to GFDL-1.1-or-later WITH no-invariant-sections ++ ++.. _V4L2-PIX-FMT-Y12P: ++ ++****************************** ++V4L2_PIX_FMT_Y12P ('Y12P') ++****************************** ++ ++Grey-scale image as a MIPI RAW12 packed array ++ ++ ++Description ++=========== ++ ++This is a packed grey-scale image format with a depth of 12 bits per ++pixel. Two consecutive pixels are packed into 3 bytes. The first 2 bytes ++contain the 8 high order bits of the pixels, and the 3rd byte contains the 4 ++least significants bits of each pixel, in the same order. ++ ++**Byte Order.** ++Each cell is one byte. ++ ++.. tabularcolumns:: |p{2.2cm}|p{1.2cm}|p{1.2cm}|p{3.1cm}| ++ ++ ++.. flat-table:: ++ :header-rows: 0 ++ :stub-columns: 0 ++ :widths: 2 1 1 1 ++ ++ ++ - - start + 0: ++ - Y'\ :sub:`00high` ++ - Y'\ :sub:`01high` ++ - Y'\ :sub:`01low`\ (bits 7--4) ++ ++ Y'\ :sub:`00low`\ (bits 3--0) ++ +--- a/Documentation/userspace-api/media/v4l/yuv-formats.rst ++++ b/Documentation/userspace-api/media/v4l/yuv-formats.rst +@@ -28,6 +28,7 @@ to brightness information. + pixfmt-grey + pixfmt-y10 + pixfmt-y12 ++ pixfmt-y12p + pixfmt-y14 + pixfmt-y10b + pixfmt-y10p +--- a/drivers/media/v4l2-core/v4l2-ioctl.c ++++ b/drivers/media/v4l2-core/v4l2-ioctl.c +@@ -1283,6 +1283,7 @@ static void v4l_fill_fmtdesc(struct v4l2 + case V4L2_PIX_FMT_Y16_BE: descr = "16-bit Greyscale BE"; break; + case V4L2_PIX_FMT_Y10BPACK: descr = "10-bit Greyscale (Packed)"; break; + case V4L2_PIX_FMT_Y10P: descr = "10-bit Greyscale (MIPI Packed)"; break; ++ case V4L2_PIX_FMT_Y12P: descr = "12-bit Greyscale (MIPI Packed)"; break; + case V4L2_PIX_FMT_Y8I: descr = "Interleaved 8-bit Greyscale"; break; + case V4L2_PIX_FMT_Y12I: descr = "Interleaved 12-bit Greyscale"; break; + case V4L2_PIX_FMT_Z16: descr = "16-bit Depth"; break; +--- a/include/uapi/linux/videodev2.h ++++ b/include/uapi/linux/videodev2.h +@@ -580,6 +580,7 @@ struct v4l2_pix_format { + /* Grey bit-packed formats */ + #define V4L2_PIX_FMT_Y10BPACK v4l2_fourcc('Y', '1', '0', 'B') /* 10 Greyscale bit-packed */ + #define V4L2_PIX_FMT_Y10P v4l2_fourcc('Y', '1', '0', 'P') /* 10 Greyscale, MIPI RAW10 packed */ ++#define V4L2_PIX_FMT_Y12P v4l2_fourcc('Y', '1', '2', 'P') /* 12 Greyscale, MIPI RAW12 packed */ + + /* Palette formats */ + #define V4L2_PIX_FMT_PAL8 v4l2_fourcc('P', 'A', 'L', '8') /* 8 8-bit palette */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0279-media-Add-a-pixel-format-for-MIPI-packed-14bit-luma-.patch b/target/linux/bcm27xx/patches-5.10/950-0279-media-Add-a-pixel-format-for-MIPI-packed-14bit-luma-.patch new file mode 100644 index 0000000000..e6b27905cb --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0279-media-Add-a-pixel-format-for-MIPI-packed-14bit-luma-.patch @@ -0,0 +1,104 @@ +From e3da593c79ce8e7ab7072fe1551fc1e8b5494eab Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 25 Jun 2020 17:51:03 +0100 +Subject: [PATCH] media: Add a pixel format for MIPI packed 14bit luma + only. + +This is the format used by monochrome 14bit image sensors. + +Signed-off-by: Dave Stevenson +--- + .../userspace-api/media/v4l/pixfmt-y14p.rst | 54 +++++++++++++++++++ + .../userspace-api/media/v4l/yuv-formats.rst | 1 + + drivers/media/v4l2-core/v4l2-ioctl.c | 1 + + include/uapi/linux/videodev2.h | 1 + + 4 files changed, 57 insertions(+) + create mode 100644 Documentation/userspace-api/media/v4l/pixfmt-y14p.rst + +--- /dev/null ++++ b/Documentation/userspace-api/media/v4l/pixfmt-y14p.rst +@@ -0,0 +1,54 @@ ++.. Permission is granted to copy, distribute and/or modify this ++.. document under the terms of the GNU Free Documentation License, ++.. Version 1.1 or any later version published by the Free Software ++.. Foundation, with no Invariant Sections, no Front-Cover Texts ++.. and no Back-Cover Texts. A copy of the license is included at ++.. Documentation/media/uapi/fdl-appendix.rst. ++.. ++.. TODO: replace it to GFDL-1.1-or-later WITH no-invariant-sections ++ ++.. _V4L2-PIX-FMT-Y14P: ++ ++************************** ++V4L2_PIX_FMT_Y14P ('Y14P') ++************************** ++ ++Grey-scale image as a MIPI RAW14 packed array ++ ++ ++Description ++=========== ++ ++This is a packed grey-scale image format with a depth of 14 bits per ++pixel. Every four consecutive samples are packed into seven bytes. Each ++of the first four bytes contain the eight high order bits of the pixels, ++and the three following bytes contains the six least significants bits of ++each pixel, in the same order. ++ ++**Byte Order.** ++Each cell is one byte. ++ ++.. tabularcolumns:: |p{1.8cm}|p{1.0cm}|p{1.0cm}|p{1.0cm}|p{1.1cm}|p{3.3cm}|p{3.3cm}|p{3.3cm}| ++ ++.. flat-table:: ++ :header-rows: 0 ++ :stub-columns: 0 ++ :widths: 2 1 1 1 1 3 3 3 ++ ++ ++ - - start + 0: ++ - Y'\ :sub:`00high` ++ - Y'\ :sub:`01high` ++ - Y'\ :sub:`02high` ++ - Y'\ :sub:`03high` ++ - Y'\ :sub:`01low bits 1--0`\ (bits 7--6) ++ ++ Y'\ :sub:`00low bits 5--0`\ (bits 5--0) ++ ++ - Y'\ :sub:`02low bits 3--0`\ (bits 7--4) ++ ++ Y'\ :sub:`01low bits 5--2`\ (bits 3--0) ++ ++ - Y'\ :sub:`03low bits 5--0`\ (bits 7--2) ++ ++ Y'\ :sub:`02low bits 5--4`\ (bits 1--0) +--- a/Documentation/userspace-api/media/v4l/yuv-formats.rst ++++ b/Documentation/userspace-api/media/v4l/yuv-formats.rst +@@ -30,6 +30,7 @@ to brightness information. + pixfmt-y12 + pixfmt-y12p + pixfmt-y14 ++ pixfmt-y14p + pixfmt-y10b + pixfmt-y10p + pixfmt-y16 +--- a/drivers/media/v4l2-core/v4l2-ioctl.c ++++ b/drivers/media/v4l2-core/v4l2-ioctl.c +@@ -1284,6 +1284,7 @@ static void v4l_fill_fmtdesc(struct v4l2 + case V4L2_PIX_FMT_Y10BPACK: descr = "10-bit Greyscale (Packed)"; break; + case V4L2_PIX_FMT_Y10P: descr = "10-bit Greyscale (MIPI Packed)"; break; + case V4L2_PIX_FMT_Y12P: descr = "12-bit Greyscale (MIPI Packed)"; break; ++ case V4L2_PIX_FMT_Y14P: descr = "14-bit Greyscale (MIPI Packed)"; break; + case V4L2_PIX_FMT_Y8I: descr = "Interleaved 8-bit Greyscale"; break; + case V4L2_PIX_FMT_Y12I: descr = "Interleaved 12-bit Greyscale"; break; + case V4L2_PIX_FMT_Z16: descr = "16-bit Depth"; break; +--- a/include/uapi/linux/videodev2.h ++++ b/include/uapi/linux/videodev2.h +@@ -581,6 +581,7 @@ struct v4l2_pix_format { + #define V4L2_PIX_FMT_Y10BPACK v4l2_fourcc('Y', '1', '0', 'B') /* 10 Greyscale bit-packed */ + #define V4L2_PIX_FMT_Y10P v4l2_fourcc('Y', '1', '0', 'P') /* 10 Greyscale, MIPI RAW10 packed */ + #define V4L2_PIX_FMT_Y12P v4l2_fourcc('Y', '1', '2', 'P') /* 12 Greyscale, MIPI RAW12 packed */ ++#define V4L2_PIX_FMT_Y14P v4l2_fourcc('Y', '1', '4', 'P') /* 14 Greyscale, MIPI RAW12 packed */ + + /* Palette formats */ + #define V4L2_PIX_FMT_PAL8 v4l2_fourcc('P', 'A', 'L', '8') /* 8 8-bit palette */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0280-media-bcm2835-unicam-Add-support-for-12bit-mono-pack.patch b/target/linux/bcm27xx/patches-5.10/950-0280-media-bcm2835-unicam-Add-support-for-12bit-mono-pack.patch new file mode 100644 index 0000000000..02cbe77f7f --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0280-media-bcm2835-unicam-Add-support-for-12bit-mono-pack.patch @@ -0,0 +1,25 @@ +From 8fc548dd572d72cda45ffc52f12f42c93049029e Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 25 Jun 2020 17:53:32 +0100 +Subject: [PATCH] media: bcm2835-unicam: Add support for 12bit mono + packed format + +Now that V4L2_PIX_FMT_Y12P is defined, allow passing raw 12bit +mono packed data through the peripheral. + +Signed-off-by: Dave Stevenson +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -336,7 +336,7 @@ static const struct unicam_fmt formats[] + .depth = 10, + .csi_dt = 0x2b, + }, { +- /* NB There is no packed V4L2 fourcc for this format. */ ++ .fourcc = V4L2_PIX_FMT_Y12P, + .repacked_fourcc = V4L2_PIX_FMT_Y12, + .code = MEDIA_BUS_FMT_Y12_1X12, + .depth = 12, diff --git a/target/linux/bcm27xx/patches-5.10/950-0281-media-bcm2835-unicam-Add-support-for-14bit-mono-sour.patch b/target/linux/bcm27xx/patches-5.10/950-0281-media-bcm2835-unicam-Add-support-for-14bit-mono-sour.patch new file mode 100644 index 0000000000..8b50dceafe --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0281-media-bcm2835-unicam-Add-support-for-14bit-mono-sour.patch @@ -0,0 +1,29 @@ +From dd3b1e96b9d27f26a0aedc2eb5eae08ba1a4ef48 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 25 Jun 2020 18:03:47 +0100 +Subject: [PATCH] media: bcm2835-unicam: Add support for 14bit mono + sources + +Now that V4L2_PIX_FMT_Y14 and V4L2_PIX_FMT_Y14P are defined, +allow passing 14bit mono data through the peripheral. + +Signed-off-by: Dave Stevenson +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 6 ++++++ + 1 file changed, 6 insertions(+) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -341,6 +341,12 @@ static const struct unicam_fmt formats[] + .code = MEDIA_BUS_FMT_Y12_1X12, + .depth = 12, + .csi_dt = 0x2c, ++ }, { ++ .fourcc = V4L2_PIX_FMT_Y14P, ++ .repacked_fourcc = V4L2_PIX_FMT_Y14, ++ .code = MEDIA_BUS_FMT_Y14_1X14, ++ .depth = 14, ++ .csi_dt = 0x2d, + }, + /* Embedded data format */ + { diff --git a/target/linux/bcm27xx/patches-5.10/950-0282-media-bcm2835-unicam-Add-support-for-unpacked-14bit-.patch b/target/linux/bcm27xx/patches-5.10/950-0282-media-bcm2835-unicam-Add-support-for-unpacked-14bit-.patch new file mode 100644 index 0000000000..f6035e1139 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0282-media-bcm2835-unicam-Add-support-for-unpacked-14bit-.patch @@ -0,0 +1,42 @@ +From bdc34f2e9bd66e717888a1867e540a6b4f85b55d Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 1 Jul 2020 10:57:57 +0100 +Subject: [PATCH] media: bcm2835-unicam: Add support for unpacked 14bit + Bayer formats + +Now that the 14bit non-packed Bayer formats are defined, add them +into the supported formats lookup table. + +Signed-off-by: Dave Stevenson +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 4 ++++ + 1 file changed, 4 insertions(+) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -299,21 +299,25 @@ static const struct unicam_fmt formats[] + .csi_dt = 0x2c, + }, { + .fourcc = V4L2_PIX_FMT_SBGGR14P, ++ .repacked_fourcc = V4L2_PIX_FMT_SBGGR14, + .code = MEDIA_BUS_FMT_SBGGR14_1X14, + .depth = 14, + .csi_dt = 0x2d, + }, { + .fourcc = V4L2_PIX_FMT_SGBRG14P, ++ .repacked_fourcc = V4L2_PIX_FMT_SGBRG14, + .code = MEDIA_BUS_FMT_SGBRG14_1X14, + .depth = 14, + .csi_dt = 0x2d, + }, { + .fourcc = V4L2_PIX_FMT_SGRBG14P, ++ .repacked_fourcc = V4L2_PIX_FMT_SGRBG14, + .code = MEDIA_BUS_FMT_SGRBG14_1X14, + .depth = 14, + .csi_dt = 0x2d, + }, { + .fourcc = V4L2_PIX_FMT_SRGGB14P, ++ .repacked_fourcc = V4L2_PIX_FMT_SRGGB14, + .code = MEDIA_BUS_FMT_SRGGB14_1X14, + .depth = 14, + .csi_dt = 0x2d, diff --git a/target/linux/bcm27xx/patches-5.10/950-0283-bcm2835-dma-Add-NO_WAIT_RESP-flag.patch b/target/linux/bcm27xx/patches-5.10/950-0283-bcm2835-dma-Add-NO_WAIT_RESP-flag.patch new file mode 100644 index 0000000000..43a7bd90c8 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0283-bcm2835-dma-Add-NO_WAIT_RESP-flag.patch @@ -0,0 +1,54 @@ +From 33528413733fa956913cfe139dcd3ddd550839e4 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 1 Jul 2020 20:28:27 +0100 +Subject: [PATCH] bcm2835-dma: Add NO_WAIT_RESP flag + +Use bit 27 of the dreq value (the second cell of the DT DMA descriptor) +to request that the WAIT_RESP bit is not set. + +Signed-off-by: Phil Elwell +--- + drivers/dma/bcm2835-dma.c | 11 ++++++++--- + 1 file changed, 8 insertions(+), 3 deletions(-) + +--- a/drivers/dma/bcm2835-dma.c ++++ b/drivers/dma/bcm2835-dma.c +@@ -165,6 +165,11 @@ struct bcm2835_desc { + #define BCM2835_DMA_WAIT(x) ((x & 31) << 21) /* add DMA-wait cycles */ + #define BCM2835_DMA_NO_WIDE_BURSTS BIT(26) /* no 2 beat write bursts */ + ++/* A fake bit to request that the driver doesn't set the WAIT_RESP bit. */ ++#define BCM2835_DMA_NO_WAIT_RESP BIT(27) ++#define WAIT_RESP(x) ((x & BCM2835_DMA_NO_WAIT_RESP) ? \ ++ 0 : BCM2835_DMA_WAIT_RESP) ++ + /* debug register bits */ + #define BCM2835_DMA_DEBUG_LAST_NOT_SET_ERR BIT(0) + #define BCM2835_DMA_DEBUG_FIFO_ERR BIT(1) +@@ -843,7 +848,7 @@ static struct dma_async_tx_descriptor *b + struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); + struct bcm2835_desc *d; + u32 info = BCM2835_DMA_D_INC | BCM2835_DMA_S_INC; +- u32 extra = BCM2835_DMA_INT_EN | BCM2835_DMA_WAIT_RESP; ++ u32 extra = BCM2835_DMA_INT_EN | WAIT_RESP(c->dreq); + size_t max_len = bcm2835_dma_max_frame_length(c); + size_t frames; + +@@ -873,7 +878,7 @@ static struct dma_async_tx_descriptor *b + struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); + struct bcm2835_desc *d; + dma_addr_t src = 0, dst = 0; +- u32 info = BCM2835_DMA_WAIT_RESP; ++ u32 info = WAIT_RESP(c->dreq); + u32 extra = BCM2835_DMA_INT_EN; + size_t frames; + +@@ -935,7 +940,7 @@ static struct dma_async_tx_descriptor *b + struct bcm2835_chan *c = to_bcm2835_dma_chan(chan); + struct bcm2835_desc *d; + dma_addr_t src, dst; +- u32 info = BCM2835_DMA_WAIT_RESP; ++ u32 info = WAIT_RESP(c->dreq); + u32 extra = 0; + size_t max_len = bcm2835_dma_max_frame_length(c); + size_t frames; diff --git a/target/linux/bcm27xx/patches-5.10/950-0284-media-i2c-add-ov9281-driver.patch b/target/linux/bcm27xx/patches-5.10/950-0284-media-i2c-add-ov9281-driver.patch new file mode 100644 index 0000000000..b807db513e --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0284-media-i2c-add-ov9281-driver.patch @@ -0,0 +1,1218 @@ +From 63ef88ff48e864eed44d25e6edd61c743e6efd30 Mon Sep 17 00:00:00 2001 +From: Zefa Chen +Date: Fri, 17 May 2019 18:23:03 +0800 +Subject: [PATCH] media: i2c: add ov9281 driver. + +Change-Id: I7b77250bbc56d2f861450cf77271ad15f9b88ab1 +Signed-off-by: Zefa Chen +--- + drivers/media/i2c/Kconfig | 11 + + drivers/media/i2c/Makefile | 1 + + drivers/media/i2c/ov9281.c | 1171 ++++++++++++++++++++++++++++++++++++ + 3 files changed, 1183 insertions(+) + create mode 100644 drivers/media/i2c/ov9281.c + +--- a/drivers/media/i2c/Kconfig ++++ b/drivers/media/i2c/Kconfig +@@ -1040,6 +1040,17 @@ config VIDEO_OV9640 + This is a Video4Linux2 sensor driver for the OmniVision + OV9640 camera sensor. + ++config VIDEO_OV9281 ++ tristate "OmniVision OV9281 sensor support" ++ depends on I2C && VIDEO_V4L2 ++ depends on MEDIA_CAMERA_SUPPORT ++ help ++ This is a Video4Linux2 sensor-level driver for the OmniVision ++ OV9281 camera. ++ ++ To compile this driver as a module, choose M here: the ++ module will be called ov9281. ++ + config VIDEO_OV9650 + tristate "OmniVision OV9650/OV9652 sensor support" + depends on I2C && VIDEO_V4L2 +--- a/drivers/media/i2c/Makefile ++++ b/drivers/media/i2c/Makefile +@@ -81,6 +81,7 @@ obj-$(CONFIG_VIDEO_OV7670) += ov7670.o + obj-$(CONFIG_VIDEO_OV772X) += ov772x.o + obj-$(CONFIG_VIDEO_OV7740) += ov7740.o + obj-$(CONFIG_VIDEO_OV8856) += ov8856.o ++obj-$(CONFIG_VIDEO_OV9281) += ov9281.o + obj-$(CONFIG_VIDEO_OV9640) += ov9640.o + obj-$(CONFIG_VIDEO_OV9650) += ov9650.o + obj-$(CONFIG_VIDEO_OV13858) += ov13858.o +--- /dev/null ++++ b/drivers/media/i2c/ov9281.c +@@ -0,0 +1,1171 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * ov9281 driver ++ * ++ * Copyright (C) 2017 Fuzhou Rockchip Electronics Co., Ltd. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define DRIVER_VERSION KERNEL_VERSION(0, 0x01, 0x0) ++ ++#ifndef V4L2_CID_DIGITAL_GAIN ++#define V4L2_CID_DIGITAL_GAIN V4L2_CID_GAIN ++#endif ++ ++#define OV9281_LINK_FREQ_400MHZ 400000000 ++/* pixel rate = link frequency * 2 * lanes / BITS_PER_SAMPLE */ ++#define OV9281_PIXEL_RATE (OV9281_LINK_FREQ_400MHZ * 2 * 2 / 10) ++#define OV9281_XVCLK_FREQ 24000000 ++ ++#define CHIP_ID 0x9281 ++#define OV9281_REG_CHIP_ID 0x300a ++ ++#define OV9281_REG_CTRL_MODE 0x0100 ++#define OV9281_MODE_SW_STANDBY 0x0 ++#define OV9281_MODE_STREAMING BIT(0) ++ ++#define OV9281_REG_EXPOSURE 0x3500 ++#define OV9281_EXPOSURE_MIN 4 ++#define OV9281_EXPOSURE_STEP 1 ++#define OV9281_VTS_MAX 0x7fff ++ ++#define OV9281_REG_GAIN_H 0x3508 ++#define OV9281_REG_GAIN_L 0x3509 ++#define OV9281_GAIN_H_MASK 0x07 ++#define OV9281_GAIN_H_SHIFT 8 ++#define OV9281_GAIN_L_MASK 0xff ++#define OV9281_GAIN_MIN 0x10 ++#define OV9281_GAIN_MAX 0xf8 ++#define OV9281_GAIN_STEP 1 ++#define OV9281_GAIN_DEFAULT 0x10 ++ ++#define OV9281_REG_TEST_PATTERN 0x5e00 ++#define OV9281_TEST_PATTERN_ENABLE 0x80 ++#define OV9281_TEST_PATTERN_DISABLE 0x0 ++ ++#define OV9281_REG_VTS 0x380e ++ ++#define REG_NULL 0xFFFF ++ ++#define OV9281_REG_VALUE_08BIT 1 ++#define OV9281_REG_VALUE_16BIT 2 ++#define OV9281_REG_VALUE_24BIT 3 ++ ++#define OV9281_LANES 2 ++#define OV9281_BITS_PER_SAMPLE 10 ++ ++#define OF_CAMERA_PINCTRL_STATE_DEFAULT "rockchip,camera_default" ++#define OF_CAMERA_PINCTRL_STATE_SLEEP "rockchip,camera_sleep" ++ ++#define OV9281_NAME "ov9281" ++ ++static const char * const ov9281_supply_names[] = { ++ "avdd", /* Analog power */ ++ "dovdd", /* Digital I/O power */ ++ "dvdd", /* Digital core power */ ++}; ++ ++#define OV9281_NUM_SUPPLIES ARRAY_SIZE(ov9281_supply_names) ++ ++struct regval { ++ u16 addr; ++ u8 val; ++}; ++ ++struct ov9281_mode { ++ u32 width; ++ u32 height; ++ u32 max_fps; ++ u32 hts_def; ++ u32 vts_def; ++ u32 exp_def; ++ const struct regval *reg_list; ++}; ++ ++struct ov9281 { ++ struct i2c_client *client; ++ struct clk *xvclk; ++ struct gpio_desc *reset_gpio; ++ struct gpio_desc *pwdn_gpio; ++ struct regulator_bulk_data supplies[OV9281_NUM_SUPPLIES]; ++ ++ struct pinctrl *pinctrl; ++ struct pinctrl_state *pins_default; ++ struct pinctrl_state *pins_sleep; ++ ++ struct v4l2_subdev subdev; ++ struct media_pad pad; ++ struct v4l2_ctrl_handler ctrl_handler; ++ struct v4l2_ctrl *exposure; ++ struct v4l2_ctrl *anal_gain; ++ struct v4l2_ctrl *digi_gain; ++ struct v4l2_ctrl *hblank; ++ struct v4l2_ctrl *vblank; ++ struct v4l2_ctrl *test_pattern; ++ struct mutex mutex; ++ bool streaming; ++ bool power_on; ++ const struct ov9281_mode *cur_mode; ++ u32 module_index; ++ const char *module_facing; ++ const char *module_name; ++ const char *len_name; ++}; ++ ++#define to_ov9281(sd) container_of(sd, struct ov9281, subdev) ++ ++/* ++ * Xclk 24Mhz ++ */ ++static const struct regval ov9281_global_regs[] = { ++ {REG_NULL, 0x00}, ++}; ++ ++/* ++ * Xclk 24Mhz ++ * max_framerate 120fps ++ * mipi_datarate per lane 800Mbps ++ */ ++static const struct regval ov9281_1280x800_regs[] = { ++ {0x0103, 0x01}, ++ {0x0302, 0x32}, ++ {0x030d, 0x50}, ++ {0x030e, 0x02}, ++ {0x3001, 0x00}, ++ {0x3004, 0x00}, ++ {0x3005, 0x00}, ++ {0x3006, 0x04}, ++ {0x3011, 0x0a}, ++ {0x3013, 0x18}, ++ {0x3022, 0x01}, ++ {0x3023, 0x00}, ++ {0x302c, 0x00}, ++ {0x302f, 0x00}, ++ {0x3030, 0x04}, ++ {0x3039, 0x32}, ++ {0x303a, 0x00}, ++ {0x303f, 0x01}, ++ {0x3500, 0x00}, ++ {0x3501, 0x2a}, ++ {0x3502, 0x90}, ++ {0x3503, 0x08}, ++ {0x3505, 0x8c}, ++ {0x3507, 0x03}, ++ {0x3508, 0x00}, ++ {0x3509, 0x10}, ++ {0x3610, 0x80}, ++ {0x3611, 0xa0}, ++ {0x3620, 0x6f}, ++ {0x3632, 0x56}, ++ {0x3633, 0x78}, ++ {0x3662, 0x05}, ++ {0x3666, 0x00}, ++ {0x366f, 0x5a}, ++ {0x3680, 0x84}, ++ {0x3712, 0x80}, ++ {0x372d, 0x22}, ++ {0x3731, 0x80}, ++ {0x3732, 0x30}, ++ {0x3778, 0x00}, ++ {0x377d, 0x22}, ++ {0x3788, 0x02}, ++ {0x3789, 0xa4}, ++ {0x378a, 0x00}, ++ {0x378b, 0x4a}, ++ {0x3799, 0x20}, ++ {0x3800, 0x00}, ++ {0x3801, 0x00}, ++ {0x3802, 0x00}, ++ {0x3803, 0x00}, ++ {0x3804, 0x05}, ++ {0x3805, 0x0f}, ++ {0x3806, 0x03}, ++ {0x3807, 0x2f}, ++ {0x3808, 0x05}, ++ {0x3809, 0x00}, ++ {0x380a, 0x03}, ++ {0x380b, 0x20}, ++ {0x380c, 0x02}, ++ {0x380d, 0xd8}, ++ {0x380e, 0x03}, ++ {0x380f, 0x8e}, ++ {0x3810, 0x00}, ++ {0x3811, 0x08}, ++ {0x3812, 0x00}, ++ {0x3813, 0x08}, ++ {0x3814, 0x11}, ++ {0x3815, 0x11}, ++ {0x3820, 0x40}, ++ {0x3821, 0x00}, ++ {0x3881, 0x42}, ++ {0x38b1, 0x00}, ++ {0x3920, 0xff}, ++ {0x4003, 0x40}, ++ {0x4008, 0x04}, ++ {0x4009, 0x0b}, ++ {0x400c, 0x00}, ++ {0x400d, 0x07}, ++ {0x4010, 0x40}, ++ {0x4043, 0x40}, ++ {0x4307, 0x30}, ++ {0x4317, 0x00}, ++ {0x4501, 0x00}, ++ {0x4507, 0x00}, ++ {0x4509, 0x00}, ++ {0x450a, 0x08}, ++ {0x4601, 0x04}, ++ {0x470f, 0x00}, ++ {0x4f07, 0x00}, ++ {0x4800, 0x00}, ++ {0x5000, 0x9f}, ++ {0x5001, 0x00}, ++ {0x5e00, 0x00}, ++ {0x5d00, 0x07}, ++ {0x5d01, 0x00}, ++ {REG_NULL, 0x00}, ++}; ++ ++static const struct ov9281_mode supported_modes[] = { ++ { ++ .width = 1280, ++ .height = 800, ++ .max_fps = 120, ++ .exp_def = 0x0320, ++ .hts_def = 0x0b60,//0x2d8*4 ++ .vts_def = 0x038e, ++ .reg_list = ov9281_1280x800_regs, ++ }, ++}; ++ ++static const s64 link_freq_menu_items[] = { ++ OV9281_LINK_FREQ_400MHZ ++}; ++ ++static const char * const ov9281_test_pattern_menu[] = { ++ "Disabled", ++ "Vertical Color Bar Type 1", ++ "Vertical Color Bar Type 2", ++ "Vertical Color Bar Type 3", ++ "Vertical Color Bar Type 4" ++}; ++ ++/* Write registers up to 4 at a time */ ++static int ov9281_write_reg(struct i2c_client *client, u16 reg, ++ u32 len, u32 val) ++{ ++ u32 buf_i, val_i; ++ u8 buf[6]; ++ u8 *val_p; ++ __be32 val_be; ++ ++ if (len > 4) ++ return -EINVAL; ++ ++ buf[0] = reg >> 8; ++ buf[1] = reg & 0xff; ++ ++ val_be = cpu_to_be32(val); ++ val_p = (u8 *)&val_be; ++ buf_i = 2; ++ val_i = 4 - len; ++ ++ while (val_i < 4) ++ buf[buf_i++] = val_p[val_i++]; ++ ++ if (i2c_master_send(client, buf, len + 2) != len + 2) ++ return -EIO; ++ ++ return 0; ++} ++ ++static int ov9281_write_array(struct i2c_client *client, ++ const struct regval *regs) ++{ ++ u32 i; ++ int ret = 0; ++ ++ for (i = 0; ret == 0 && regs[i].addr != REG_NULL; i++) ++ ret = ov9281_write_reg(client, regs[i].addr, ++ OV9281_REG_VALUE_08BIT, regs[i].val); ++ ++ return ret; ++} ++ ++/* Read registers up to 4 at a time */ ++static int ov9281_read_reg(struct i2c_client *client, u16 reg, unsigned int len, ++ u32 *val) ++{ ++ struct i2c_msg msgs[2]; ++ u8 *data_be_p; ++ __be32 data_be = 0; ++ __be16 reg_addr_be = cpu_to_be16(reg); ++ int ret; ++ ++ if (len > 4 || !len) ++ return -EINVAL; ++ ++ data_be_p = (u8 *)&data_be; ++ /* Write register address */ ++ msgs[0].addr = client->addr; ++ msgs[0].flags = 0; ++ msgs[0].len = 2; ++ msgs[0].buf = (u8 *)®_addr_be; ++ ++ /* Read data from register */ ++ msgs[1].addr = client->addr; ++ msgs[1].flags = I2C_M_RD; ++ msgs[1].len = len; ++ msgs[1].buf = &data_be_p[4 - len]; ++ ++ ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs)); ++ if (ret != ARRAY_SIZE(msgs)) ++ return -EIO; ++ ++ *val = be32_to_cpu(data_be); ++ ++ return 0; ++} ++ ++static int ov9281_get_reso_dist(const struct ov9281_mode *mode, ++ struct v4l2_mbus_framefmt *framefmt) ++{ ++ return abs(mode->width - framefmt->width) + ++ abs(mode->height - framefmt->height); ++} ++ ++static const struct ov9281_mode * ++ov9281_find_best_fit(struct v4l2_subdev_format *fmt) ++{ ++ struct v4l2_mbus_framefmt *framefmt = &fmt->format; ++ int dist; ++ int cur_best_fit = 0; ++ int cur_best_fit_dist = -1; ++ unsigned int i; ++ ++ for (i = 0; i < ARRAY_SIZE(supported_modes); i++) { ++ dist = ov9281_get_reso_dist(&supported_modes[i], framefmt); ++ if (cur_best_fit_dist == -1 || dist < cur_best_fit_dist) { ++ cur_best_fit_dist = dist; ++ cur_best_fit = i; ++ } ++ } ++ ++ return &supported_modes[cur_best_fit]; ++} ++ ++static int ov9281_set_fmt(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_format *fmt) ++{ ++ struct ov9281 *ov9281 = to_ov9281(sd); ++ const struct ov9281_mode *mode; ++ s64 h_blank, vblank_def; ++ ++ mutex_lock(&ov9281->mutex); ++ ++ mode = ov9281_find_best_fit(fmt); ++ fmt->format.code = MEDIA_BUS_FMT_Y10_1X10; ++ fmt->format.width = mode->width; ++ fmt->format.height = mode->height; ++ fmt->format.field = V4L2_FIELD_NONE; ++ if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { ++#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API ++ *v4l2_subdev_get_try_format(sd, cfg, fmt->pad) = fmt->format; ++#else ++ mutex_unlock(&ov9281->mutex); ++ return -ENOTTY; ++#endif ++ } else { ++ ov9281->cur_mode = mode; ++ h_blank = mode->hts_def - mode->width; ++ __v4l2_ctrl_modify_range(ov9281->hblank, h_blank, ++ h_blank, 1, h_blank); ++ vblank_def = mode->vts_def - mode->height; ++ __v4l2_ctrl_modify_range(ov9281->vblank, vblank_def, ++ OV9281_VTS_MAX - mode->height, ++ 1, vblank_def); ++ } ++ ++ mutex_unlock(&ov9281->mutex); ++ ++ return 0; ++} ++ ++static int ov9281_get_fmt(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_format *fmt) ++{ ++ struct ov9281 *ov9281 = to_ov9281(sd); ++ const struct ov9281_mode *mode = ov9281->cur_mode; ++ ++ mutex_lock(&ov9281->mutex); ++ if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { ++#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API ++ fmt->format = *v4l2_subdev_get_try_format(sd, cfg, fmt->pad); ++#else ++ mutex_unlock(&ov9281->mutex); ++ return -ENOTTY; ++#endif ++ } else { ++ fmt->format.width = mode->width; ++ fmt->format.height = mode->height; ++ fmt->format.code = MEDIA_BUS_FMT_Y10_1X10; ++ fmt->format.field = V4L2_FIELD_NONE; ++ } ++ mutex_unlock(&ov9281->mutex); ++ ++ return 0; ++} ++ ++static int ov9281_enum_mbus_code(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_mbus_code_enum *code) ++{ ++ if (code->index != 0) ++ return -EINVAL; ++ code->code = MEDIA_BUS_FMT_Y10_1X10; ++ ++ return 0; ++} ++ ++static int ov9281_enum_frame_sizes(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_frame_size_enum *fse) ++{ ++ if (fse->index >= ARRAY_SIZE(supported_modes)) ++ return -EINVAL; ++ ++ if (fse->code != MEDIA_BUS_FMT_Y10_1X10) ++ return -EINVAL; ++ ++ fse->min_width = supported_modes[fse->index].width; ++ fse->max_width = supported_modes[fse->index].width; ++ fse->max_height = supported_modes[fse->index].height; ++ fse->min_height = supported_modes[fse->index].height; ++ ++ return 0; ++} ++ ++static int ov9281_enable_test_pattern(struct ov9281 *ov9281, u32 pattern) ++{ ++ u32 val; ++ ++ if (pattern) ++ val = (pattern - 1) | OV9281_TEST_PATTERN_ENABLE; ++ else ++ val = OV9281_TEST_PATTERN_DISABLE; ++ ++ return ov9281_write_reg(ov9281->client, OV9281_REG_TEST_PATTERN, ++ OV9281_REG_VALUE_08BIT, val); ++} ++ ++static int OV9281_g_frame_interval(struct v4l2_subdev *sd, ++ struct v4l2_subdev_frame_interval *fi) ++{ ++ struct ov9281 *ov9281 = to_ov9281(sd); ++ const struct ov9281_mode *mode = ov9281->cur_mode; ++ ++ mutex_lock(&ov9281->mutex); ++ fi->interval.numerator = 10000; ++ fi->interval.denominator = mode->max_fps * 10000; ++ mutex_unlock(&ov9281->mutex); ++ ++ return 0; ++} ++ ++static void ov9281_get_module_inf(struct ov9281 *ov9281, ++ struct rkmodule_inf *inf) ++{ ++ memset(inf, 0, sizeof(*inf)); ++ strlcpy(inf->base.sensor, OV9281_NAME, sizeof(inf->base.sensor)); ++ strlcpy(inf->base.module, ov9281->module_name, ++ sizeof(inf->base.module)); ++ strlcpy(inf->base.lens, ov9281->len_name, sizeof(inf->base.lens)); ++} ++ ++static long ov9281_ioctl(struct v4l2_subdev *sd, unsigned int cmd, void *arg) ++{ ++ struct ov9281 *ov9281 = to_ov9281(sd); ++ long ret = 0; ++ ++ switch (cmd) { ++ case RKMODULE_GET_MODULE_INFO: ++ ov9281_get_module_inf(ov9281, (struct rkmodule_inf *)arg); ++ break; ++ default: ++ ret = -ENOIOCTLCMD; ++ break; ++ } ++ ++ return ret; ++} ++ ++#ifdef CONFIG_COMPAT ++static long ov9281_compat_ioctl32(struct v4l2_subdev *sd, ++ unsigned int cmd, unsigned long arg) ++{ ++ void __user *up = compat_ptr(arg); ++ struct rkmodule_inf *inf; ++ struct rkmodule_awb_cfg *cfg; ++ long ret; ++ ++ switch (cmd) { ++ case RKMODULE_GET_MODULE_INFO: ++ inf = kzalloc(sizeof(*inf), GFP_KERNEL); ++ if (!inf) { ++ ret = -ENOMEM; ++ return ret; ++ } ++ ++ ret = ov9281_ioctl(sd, cmd, inf); ++ if (!ret) ++ ret = copy_to_user(up, inf, sizeof(*inf)); ++ kfree(inf); ++ break; ++ case RKMODULE_AWB_CFG: ++ cfg = kzalloc(sizeof(*cfg), GFP_KERNEL); ++ if (!cfg) { ++ ret = -ENOMEM; ++ return ret; ++ } ++ ++ ret = copy_from_user(cfg, up, sizeof(*cfg)); ++ if (!ret) ++ ret = ov9281_ioctl(sd, cmd, cfg); ++ kfree(cfg); ++ break; ++ default: ++ ret = -ENOIOCTLCMD; ++ break; ++ } ++ ++ return ret; ++} ++#endif ++ ++static int __ov9281_start_stream(struct ov9281 *ov9281) ++{ ++ int ret; ++ ++ ret = ov9281_write_array(ov9281->client, ov9281->cur_mode->reg_list); ++ if (ret) ++ return ret; ++ ++ /* In case these controls are set before streaming */ ++ mutex_unlock(&ov9281->mutex); ++ ret = v4l2_ctrl_handler_setup(&ov9281->ctrl_handler); ++ mutex_lock(&ov9281->mutex); ++ if (ret) ++ return ret; ++ ++ return ov9281_write_reg(ov9281->client, OV9281_REG_CTRL_MODE, ++ OV9281_REG_VALUE_08BIT, OV9281_MODE_STREAMING); ++} ++ ++static int __ov9281_stop_stream(struct ov9281 *ov9281) ++{ ++ return ov9281_write_reg(ov9281->client, OV9281_REG_CTRL_MODE, ++ OV9281_REG_VALUE_08BIT, OV9281_MODE_SW_STANDBY); ++} ++ ++static int ov9281_s_stream(struct v4l2_subdev *sd, int on) ++{ ++ struct ov9281 *ov9281 = to_ov9281(sd); ++ struct i2c_client *client = ov9281->client; ++ int ret = 0; ++ ++ mutex_lock(&ov9281->mutex); ++ on = !!on; ++ if (on == ov9281->streaming) ++ goto unlock_and_return; ++ ++ if (on) { ++ ret = pm_runtime_get_sync(&client->dev); ++ if (ret < 0) { ++ pm_runtime_put_noidle(&client->dev); ++ goto unlock_and_return; ++ } ++ ++ ret = __ov9281_start_stream(ov9281); ++ if (ret) { ++ v4l2_err(sd, "start stream failed while write regs\n"); ++ pm_runtime_put(&client->dev); ++ goto unlock_and_return; ++ } ++ } else { ++ __ov9281_stop_stream(ov9281); ++ pm_runtime_put(&client->dev); ++ } ++ ++ ov9281->streaming = on; ++ ++unlock_and_return: ++ mutex_unlock(&ov9281->mutex); ++ ++ return ret; ++} ++ ++static int ov9281_s_power(struct v4l2_subdev *sd, int on) ++{ ++ struct ov9281 *ov9281 = to_ov9281(sd); ++ struct i2c_client *client = ov9281->client; ++ int ret = 0; ++ ++ mutex_lock(&ov9281->mutex); ++ ++ /* If the power state is not modified - no work to do. */ ++ if (ov9281->power_on == !!on) ++ goto unlock_and_return; ++ ++ if (on) { ++ ret = pm_runtime_get_sync(&client->dev); ++ if (ret < 0) { ++ pm_runtime_put_noidle(&client->dev); ++ goto unlock_and_return; ++ } ++ ret = ov9281_write_array(ov9281->client, ov9281_global_regs); ++ if (ret) { ++ v4l2_err(sd, "could not set init registers\n"); ++ pm_runtime_put_noidle(&client->dev); ++ goto unlock_and_return; ++ } ++ ov9281->power_on = true; ++ } else { ++ pm_runtime_put(&client->dev); ++ ov9281->power_on = false; ++ } ++ ++unlock_and_return: ++ mutex_unlock(&ov9281->mutex); ++ ++ return ret; ++} ++ ++/* Calculate the delay in us by clock rate and clock cycles */ ++static inline u32 ov9281_cal_delay(u32 cycles) ++{ ++ return DIV_ROUND_UP(cycles, OV9281_XVCLK_FREQ / 1000 / 1000); ++} ++ ++static int __ov9281_power_on(struct ov9281 *ov9281) ++{ ++ int ret; ++ u32 delay_us; ++ struct device *dev = &ov9281->client->dev; ++ ++ if (!IS_ERR_OR_NULL(ov9281->pins_default)) { ++ ret = pinctrl_select_state(ov9281->pinctrl, ++ ov9281->pins_default); ++ if (ret < 0) ++ dev_err(dev, "could not set pins\n"); ++ } ++ ++ ret = clk_prepare_enable(ov9281->xvclk); ++ if (ret < 0) { ++ dev_err(dev, "Failed to enable xvclk\n"); ++ return ret; ++ } ++ ++ if (!IS_ERR(ov9281->reset_gpio)) ++ gpiod_set_value_cansleep(ov9281->reset_gpio, 0); ++ ++ ret = regulator_bulk_enable(OV9281_NUM_SUPPLIES, ov9281->supplies); ++ if (ret < 0) { ++ dev_err(dev, "Failed to enable regulators\n"); ++ goto disable_clk; ++ } ++ ++ if (!IS_ERR(ov9281->reset_gpio)) ++ gpiod_set_value_cansleep(ov9281->reset_gpio, 1); ++ ++ usleep_range(500, 1000); ++ if (!IS_ERR(ov9281->pwdn_gpio)) ++ gpiod_set_value_cansleep(ov9281->pwdn_gpio, 1); ++ ++ /* 8192 cycles prior to first SCCB transaction */ ++ delay_us = ov9281_cal_delay(8192); ++ usleep_range(delay_us, delay_us * 2); ++ ++ return 0; ++ ++disable_clk: ++ clk_disable_unprepare(ov9281->xvclk); ++ ++ return ret; ++} ++ ++static void __ov9281_power_off(struct ov9281 *ov9281) ++{ ++ int ret; ++ struct device *dev = &ov9281->client->dev; ++ ++ if (!IS_ERR(ov9281->pwdn_gpio)) ++ gpiod_set_value_cansleep(ov9281->pwdn_gpio, 0); ++ clk_disable_unprepare(ov9281->xvclk); ++ if (!IS_ERR(ov9281->reset_gpio)) ++ gpiod_set_value_cansleep(ov9281->reset_gpio, 0); ++ if (!IS_ERR_OR_NULL(ov9281->pins_sleep)) { ++ ret = pinctrl_select_state(ov9281->pinctrl, ++ ov9281->pins_sleep); ++ if (ret < 0) ++ dev_dbg(dev, "could not set pins\n"); ++ } ++ regulator_bulk_disable(OV9281_NUM_SUPPLIES, ov9281->supplies); ++} ++ ++static int ov9281_runtime_resume(struct device *dev) ++{ ++ struct i2c_client *client = to_i2c_client(dev); ++ struct v4l2_subdev *sd = i2c_get_clientdata(client); ++ struct ov9281 *ov9281 = to_ov9281(sd); ++ ++ return __ov9281_power_on(ov9281); ++} ++ ++static int ov9281_runtime_suspend(struct device *dev) ++{ ++ struct i2c_client *client = to_i2c_client(dev); ++ struct v4l2_subdev *sd = i2c_get_clientdata(client); ++ struct ov9281 *ov9281 = to_ov9281(sd); ++ ++ __ov9281_power_off(ov9281); ++ ++ return 0; ++} ++ ++#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API ++static int ov9281_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) ++{ ++ struct ov9281 *ov9281 = to_ov9281(sd); ++ struct v4l2_mbus_framefmt *try_fmt = ++ v4l2_subdev_get_try_format(sd, fh->pad, 0); ++ const struct ov9281_mode *def_mode = &supported_modes[0]; ++ ++ mutex_lock(&ov9281->mutex); ++ /* Initialize try_fmt */ ++ try_fmt->width = def_mode->width; ++ try_fmt->height = def_mode->height; ++ try_fmt->code = MEDIA_BUS_FMT_Y10_1X10; ++ try_fmt->field = V4L2_FIELD_NONE; ++ ++ mutex_unlock(&ov9281->mutex); ++ /* No crop or compose */ ++ ++ return 0; ++} ++#endif ++ ++static const struct dev_pm_ops ov9281_pm_ops = { ++ SET_RUNTIME_PM_OPS(ov9281_runtime_suspend, ++ ov9281_runtime_resume, NULL) ++}; ++ ++#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API ++static const struct v4l2_subdev_internal_ops ov9281_internal_ops = { ++ .open = ov9281_open, ++}; ++#endif ++ ++static const struct v4l2_subdev_core_ops ov9281_core_ops = { ++ .s_power = ov9281_s_power, ++ .ioctl = ov9281_ioctl, ++#ifdef CONFIG_COMPAT ++ .compat_ioctl32 = ov9281_compat_ioctl32, ++#endif ++}; ++ ++static const struct v4l2_subdev_video_ops ov9281_video_ops = { ++ .s_stream = ov9281_s_stream, ++ .g_frame_interval = OV9281_g_frame_interval, ++}; ++ ++static const struct v4l2_subdev_pad_ops ov9281_pad_ops = { ++ .enum_mbus_code = ov9281_enum_mbus_code, ++ .enum_frame_size = ov9281_enum_frame_sizes, ++ .get_fmt = ov9281_get_fmt, ++ .set_fmt = ov9281_set_fmt, ++}; ++ ++static const struct v4l2_subdev_ops ov9281_subdev_ops = { ++ .core = &ov9281_core_ops, ++ .video = &ov9281_video_ops, ++ .pad = &ov9281_pad_ops, ++}; ++ ++static int ov9281_set_ctrl(struct v4l2_ctrl *ctrl) ++{ ++ struct ov9281 *ov9281 = container_of(ctrl->handler, ++ struct ov9281, ctrl_handler); ++ struct i2c_client *client = ov9281->client; ++ s64 max; ++ int ret = 0; ++ ++ /* Propagate change of current control to all related controls */ ++ switch (ctrl->id) { ++ case V4L2_CID_VBLANK: ++ /* Update max exposure while meeting expected vblanking */ ++ max = ov9281->cur_mode->height + ctrl->val - 4; ++ __v4l2_ctrl_modify_range(ov9281->exposure, ++ ov9281->exposure->minimum, max, ++ ov9281->exposure->step, ++ ov9281->exposure->default_value); ++ break; ++ } ++ ++ if (pm_runtime_get(&client->dev) <= 0) ++ return 0; ++ ++ switch (ctrl->id) { ++ case V4L2_CID_EXPOSURE: ++ /* 4 least significant bits of expsoure are fractional part */ ++ ret = ov9281_write_reg(ov9281->client, OV9281_REG_EXPOSURE, ++ OV9281_REG_VALUE_24BIT, ctrl->val << 4); ++ break; ++ case V4L2_CID_ANALOGUE_GAIN: ++ ret = ov9281_write_reg(ov9281->client, OV9281_REG_GAIN_H, ++ OV9281_REG_VALUE_08BIT, ++ (ctrl->val >> OV9281_GAIN_H_SHIFT) & OV9281_GAIN_H_MASK); ++ ret |= ov9281_write_reg(ov9281->client, OV9281_REG_GAIN_L, ++ OV9281_REG_VALUE_08BIT, ++ ctrl->val & OV9281_GAIN_L_MASK); ++ break; ++ case V4L2_CID_VBLANK: ++ ret = ov9281_write_reg(ov9281->client, OV9281_REG_VTS, ++ OV9281_REG_VALUE_16BIT, ++ ctrl->val + ov9281->cur_mode->height); ++ break; ++ case V4L2_CID_TEST_PATTERN: ++ ret = ov9281_enable_test_pattern(ov9281, ctrl->val); ++ break; ++ default: ++ dev_warn(&client->dev, "%s Unhandled id:0x%x, val:0x%x\n", ++ __func__, ctrl->id, ctrl->val); ++ break; ++ } ++ ++ pm_runtime_put(&client->dev); ++ ++ return ret; ++} ++ ++static const struct v4l2_ctrl_ops ov9281_ctrl_ops = { ++ .s_ctrl = ov9281_set_ctrl, ++}; ++ ++static int ov9281_initialize_controls(struct ov9281 *ov9281) ++{ ++ const struct ov9281_mode *mode; ++ struct v4l2_ctrl_handler *handler; ++ struct v4l2_ctrl *ctrl; ++ s64 exposure_max, vblank_def; ++ u32 h_blank; ++ int ret; ++ ++ handler = &ov9281->ctrl_handler; ++ mode = ov9281->cur_mode; ++ ret = v4l2_ctrl_handler_init(handler, 8); ++ if (ret) ++ return ret; ++ handler->lock = &ov9281->mutex; ++ ++ ctrl = v4l2_ctrl_new_int_menu(handler, NULL, V4L2_CID_LINK_FREQ, ++ 0, 0, link_freq_menu_items); ++ if (ctrl) ++ ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY; ++ ++ v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE, ++ 0, OV9281_PIXEL_RATE, 1, OV9281_PIXEL_RATE); ++ ++ h_blank = mode->hts_def - mode->width; ++ ov9281->hblank = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK, ++ h_blank, h_blank, 1, h_blank); ++ if (ov9281->hblank) ++ ov9281->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY; ++ ++ vblank_def = mode->vts_def - mode->height; ++ ov9281->vblank = v4l2_ctrl_new_std(handler, &ov9281_ctrl_ops, ++ V4L2_CID_VBLANK, vblank_def, ++ OV9281_VTS_MAX - mode->height, ++ 1, vblank_def); ++ ++ exposure_max = mode->vts_def - 4; ++ ov9281->exposure = v4l2_ctrl_new_std(handler, &ov9281_ctrl_ops, ++ V4L2_CID_EXPOSURE, OV9281_EXPOSURE_MIN, ++ exposure_max, OV9281_EXPOSURE_STEP, ++ mode->exp_def); ++ ++ ov9281->anal_gain = v4l2_ctrl_new_std(handler, &ov9281_ctrl_ops, ++ V4L2_CID_ANALOGUE_GAIN, OV9281_GAIN_MIN, ++ OV9281_GAIN_MAX, OV9281_GAIN_STEP, ++ OV9281_GAIN_DEFAULT); ++ ++ ov9281->test_pattern = v4l2_ctrl_new_std_menu_items(handler, ++ &ov9281_ctrl_ops, V4L2_CID_TEST_PATTERN, ++ ARRAY_SIZE(ov9281_test_pattern_menu) - 1, ++ 0, 0, ov9281_test_pattern_menu); ++ ++ if (handler->error) { ++ ret = handler->error; ++ dev_err(&ov9281->client->dev, ++ "Failed to init controls(%d)\n", ret); ++ goto err_free_handler; ++ } ++ ++ ov9281->subdev.ctrl_handler = handler; ++ ++ return 0; ++ ++err_free_handler: ++ v4l2_ctrl_handler_free(handler); ++ ++ return ret; ++} ++ ++static int ov9281_check_sensor_id(struct ov9281 *ov9281, ++ struct i2c_client *client) ++{ ++ struct device *dev = &ov9281->client->dev; ++ u32 id = 0; ++ int ret; ++ ++ ret = ov9281_read_reg(client, OV9281_REG_CHIP_ID, ++ OV9281_REG_VALUE_16BIT, &id); ++ if (id != CHIP_ID) { ++ dev_err(dev, "Unexpected sensor id(%06x), ret(%d)\n", id, ret); ++ return -ENODEV; ++ } ++ ++ dev_info(dev, "Detected OV%06x sensor\n", CHIP_ID); ++ ++ return 0; ++} ++ ++static int ov9281_configure_regulators(struct ov9281 *ov9281) ++{ ++ unsigned int i; ++ ++ for (i = 0; i < OV9281_NUM_SUPPLIES; i++) ++ ov9281->supplies[i].supply = ov9281_supply_names[i]; ++ ++ return devm_regulator_bulk_get(&ov9281->client->dev, ++ OV9281_NUM_SUPPLIES, ++ ov9281->supplies); ++} ++ ++static int ov9281_probe(struct i2c_client *client, ++ const struct i2c_device_id *id) ++{ ++ struct device *dev = &client->dev; ++ struct device_node *node = dev->of_node; ++ struct ov9281 *ov9281; ++ struct v4l2_subdev *sd; ++ char facing[2]; ++ int ret; ++ ++ dev_info(dev, "driver version: %02x.%02x.%02x", ++ DRIVER_VERSION >> 16, ++ (DRIVER_VERSION & 0xff00) >> 8, ++ DRIVER_VERSION & 0x00ff); ++ ++ ov9281 = devm_kzalloc(dev, sizeof(*ov9281), GFP_KERNEL); ++ if (!ov9281) ++ return -ENOMEM; ++ ++ ret = of_property_read_u32(node, RKMODULE_CAMERA_MODULE_INDEX, ++ &ov9281->module_index); ++ ret |= of_property_read_string(node, RKMODULE_CAMERA_MODULE_FACING, ++ &ov9281->module_facing); ++ ret |= of_property_read_string(node, RKMODULE_CAMERA_MODULE_NAME, ++ &ov9281->module_name); ++ ret |= of_property_read_string(node, RKMODULE_CAMERA_LENS_NAME, ++ &ov9281->len_name); ++ if (ret) { ++ dev_err(dev, "could not get module information!\n"); ++ return -EINVAL; ++ } ++ ++ ov9281->client = client; ++ ov9281->cur_mode = &supported_modes[0]; ++ ++ ov9281->xvclk = devm_clk_get(dev, "xvclk"); ++ if (IS_ERR(ov9281->xvclk)) { ++ dev_err(dev, "Failed to get xvclk\n"); ++ return -EINVAL; ++ } ++ ret = clk_set_rate(ov9281->xvclk, OV9281_XVCLK_FREQ); ++ if (ret < 0) { ++ dev_err(dev, "Failed to set xvclk rate (24MHz)\n"); ++ return ret; ++ } ++ if (clk_get_rate(ov9281->xvclk) != OV9281_XVCLK_FREQ) ++ dev_warn(dev, "xvclk mismatched, modes are based on 24MHz\n"); ++ ++ ov9281->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); ++ if (IS_ERR(ov9281->reset_gpio)) ++ dev_warn(dev, "Failed to get reset-gpios\n"); ++ ++ ov9281->pwdn_gpio = devm_gpiod_get(dev, "pwdn", GPIOD_OUT_LOW); ++ if (IS_ERR(ov9281->pwdn_gpio)) ++ dev_warn(dev, "Failed to get pwdn-gpios\n"); ++ ++ ov9281->pinctrl = devm_pinctrl_get(dev); ++ if (!IS_ERR(ov9281->pinctrl)) { ++ ov9281->pins_default = ++ pinctrl_lookup_state(ov9281->pinctrl, ++ OF_CAMERA_PINCTRL_STATE_DEFAULT); ++ if (IS_ERR(ov9281->pins_default)) ++ dev_err(dev, "could not get default pinstate\n"); ++ ++ ov9281->pins_sleep = ++ pinctrl_lookup_state(ov9281->pinctrl, ++ OF_CAMERA_PINCTRL_STATE_SLEEP); ++ if (IS_ERR(ov9281->pins_sleep)) ++ dev_err(dev, "could not get sleep pinstate\n"); ++ } else { ++ dev_err(dev, "no pinctrl\n"); ++ } ++ ++ ret = ov9281_configure_regulators(ov9281); ++ if (ret) { ++ dev_err(dev, "Failed to get power regulators\n"); ++ return ret; ++ } ++ ++ mutex_init(&ov9281->mutex); ++ ++ sd = &ov9281->subdev; ++ v4l2_i2c_subdev_init(sd, client, &ov9281_subdev_ops); ++ ret = ov9281_initialize_controls(ov9281); ++ if (ret) ++ goto err_destroy_mutex; ++ ++ ret = __ov9281_power_on(ov9281); ++ if (ret) ++ goto err_free_handler; ++ ++ ret = ov9281_check_sensor_id(ov9281, client); ++ if (ret) ++ goto err_power_off; ++ ++#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API ++ sd->internal_ops = &ov9281_internal_ops; ++ sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; ++#endif ++#if defined(CONFIG_MEDIA_CONTROLLER) ++ ov9281->pad.flags = MEDIA_PAD_FL_SOURCE; ++ sd->entity.type = MEDIA_ENT_T_V4L2_SUBDEV_SENSOR; ++ ret = media_entity_init(&sd->entity, 1, &ov9281->pad, 0); ++ if (ret < 0) ++ goto err_power_off; ++#endif ++ ++ memset(facing, 0, sizeof(facing)); ++ if (strcmp(ov9281->module_facing, "back") == 0) ++ facing[0] = 'b'; ++ else ++ facing[0] = 'f'; ++ ++ snprintf(sd->name, sizeof(sd->name), "m%02d_%s_%s %s", ++ ov9281->module_index, facing, ++ OV9281_NAME, dev_name(sd->dev)); ++ ret = v4l2_async_register_subdev_sensor_common(sd); ++ if (ret) { ++ dev_err(dev, "v4l2 async register subdev failed\n"); ++ goto err_clean_entity; ++ } ++ ++ pm_runtime_set_active(dev); ++ pm_runtime_enable(dev); ++ pm_runtime_idle(dev); ++ ++ return 0; ++ ++err_clean_entity: ++#if defined(CONFIG_MEDIA_CONTROLLER) ++ media_entity_cleanup(&sd->entity); ++#endif ++err_power_off: ++ __ov9281_power_off(ov9281); ++err_free_handler: ++ v4l2_ctrl_handler_free(&ov9281->ctrl_handler); ++err_destroy_mutex: ++ mutex_destroy(&ov9281->mutex); ++ ++ return ret; ++} ++ ++static int ov9281_remove(struct i2c_client *client) ++{ ++ struct v4l2_subdev *sd = i2c_get_clientdata(client); ++ struct ov9281 *ov9281 = to_ov9281(sd); ++ ++ v4l2_async_unregister_subdev(sd); ++#if defined(CONFIG_MEDIA_CONTROLLER) ++ media_entity_cleanup(&sd->entity); ++#endif ++ v4l2_ctrl_handler_free(&ov9281->ctrl_handler); ++ mutex_destroy(&ov9281->mutex); ++ ++ pm_runtime_disable(&client->dev); ++ if (!pm_runtime_status_suspended(&client->dev)) ++ __ov9281_power_off(ov9281); ++ pm_runtime_set_suspended(&client->dev); ++ ++ return 0; ++} ++ ++#if IS_ENABLED(CONFIG_OF) ++static const struct of_device_id ov9281_of_match[] = { ++ { .compatible = "ovti,ov9281" }, ++ {}, ++}; ++MODULE_DEVICE_TABLE(of, ov9281_of_match); ++#endif ++ ++static const struct i2c_device_id ov9281_match_id[] = { ++ { "ovti,ov9281", 0 }, ++ { }, ++}; ++ ++static struct i2c_driver ov9281_i2c_driver = { ++ .driver = { ++ .name = OV9281_NAME, ++ .pm = &ov9281_pm_ops, ++ .of_match_table = of_match_ptr(ov9281_of_match), ++ }, ++ .probe = &ov9281_probe, ++ .remove = &ov9281_remove, ++ .id_table = ov9281_match_id, ++}; ++ ++static int __init sensor_mod_init(void) ++{ ++ return i2c_add_driver(&ov9281_i2c_driver); ++} ++ ++static void __exit sensor_mod_exit(void) ++{ ++ i2c_del_driver(&ov9281_i2c_driver); ++} ++ ++device_initcall_sync(sensor_mod_init); ++module_exit(sensor_mod_exit); ++ ++MODULE_DESCRIPTION("OmniVision ov9281 sensor driver"); ++MODULE_LICENSE("GPL v2"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0285-media-i2c-ov9281-fix-mclk-issue-when-probe-multiple-.patch b/target/linux/bcm27xx/patches-5.10/950-0285-media-i2c-ov9281-fix-mclk-issue-when-probe-multiple-.patch new file mode 100644 index 0000000000..b444221198 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0285-media-i2c-ov9281-fix-mclk-issue-when-probe-multiple-.patch @@ -0,0 +1,60 @@ +From ecaf713a6535e49f1eb4374f6241421e8e61d407 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 14 Apr 2020 15:47:09 +0100 +Subject: [PATCH] media: i2c: ov9281: fix mclk issue when probe + multiple camera. + +Takes the ov9281 part only from the Rockchip's patch. + +Change-Id: I30e833baf2c1bb07d6d87ddb3b00759ab45a90e4 +Signed-off-by: Zefa Chen +--- + drivers/media/i2c/ov9281.c | 16 ++++++++-------- + 1 file changed, 8 insertions(+), 8 deletions(-) + +--- a/drivers/media/i2c/ov9281.c ++++ b/drivers/media/i2c/ov9281.c +@@ -3,6 +3,7 @@ + * ov9281 driver + * + * Copyright (C) 2017 Fuzhou Rockchip Electronics Co., Ltd. ++ * V0.0X01.0X02 fix mclk issue when probe multiple camera. + */ + + #include +@@ -22,7 +23,7 @@ + #include + #include + +-#define DRIVER_VERSION KERNEL_VERSION(0, 0x01, 0x0) ++#define DRIVER_VERSION KERNEL_VERSION(0, 0x01, 0x2) + + #ifndef V4L2_CID_DIGITAL_GAIN + #define V4L2_CID_DIGITAL_GAIN V4L2_CID_GAIN +@@ -676,6 +677,12 @@ static int __ov9281_power_on(struct ov92 + dev_err(dev, "could not set pins\n"); + } + ++ ret = clk_set_rate(ov9281->xvclk, OV9281_XVCLK_FREQ); ++ if (ret < 0) ++ dev_warn(dev, "Failed to set xvclk rate (24MHz)\n"); ++ if (clk_get_rate(ov9281->xvclk) != OV9281_XVCLK_FREQ) ++ dev_warn(dev, "xvclk mismatched, modes are based on 24MHz\n"); ++ + ret = clk_prepare_enable(ov9281->xvclk); + if (ret < 0) { + dev_err(dev, "Failed to enable xvclk\n"); +@@ -1008,13 +1015,6 @@ static int ov9281_probe(struct i2c_clien + dev_err(dev, "Failed to get xvclk\n"); + return -EINVAL; + } +- ret = clk_set_rate(ov9281->xvclk, OV9281_XVCLK_FREQ); +- if (ret < 0) { +- dev_err(dev, "Failed to set xvclk rate (24MHz)\n"); +- return ret; +- } +- if (clk_get_rate(ov9281->xvclk) != OV9281_XVCLK_FREQ) +- dev_warn(dev, "xvclk mismatched, modes are based on 24MHz\n"); + + ov9281->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); + if (IS_ERR(ov9281->reset_gpio)) diff --git a/target/linux/bcm27xx/patches-5.10/950-0286-media-i2c-ov9281-add-enum_frame_interval-function-fo.patch b/target/linux/bcm27xx/patches-5.10/950-0286-media-i2c-ov9281-add-enum_frame_interval-function-fo.patch new file mode 100644 index 0000000000..aab12fe4b1 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0286-media-i2c-ov9281-add-enum_frame_interval-function-fo.patch @@ -0,0 +1,97 @@ +From ffb4500f4c368183fb71ce20698eb4bd25bc0ed7 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 14 Apr 2020 15:51:50 +0100 +Subject: [PATCH] media: i2c: ov9281: add enum_frame_interval function + for iq tool 2.2 and hal3 + +Adds the ov9281 parts of the Rockchip patch adding enum_frame_interval to +a large number of drivers. + +Change-Id: I03344cd6cf278dd7c18fce8e97479089ef185a5c +Signed-off-by: Zefa Chen +--- + drivers/media/i2c/ov9281.c | 31 ++++++++++++++++++++++++++----- + 1 file changed, 26 insertions(+), 5 deletions(-) + +--- a/drivers/media/i2c/ov9281.c ++++ b/drivers/media/i2c/ov9281.c +@@ -4,6 +4,7 @@ + * + * Copyright (C) 2017 Fuzhou Rockchip Electronics Co., Ltd. + * V0.0X01.0X02 fix mclk issue when probe multiple camera. ++ * V0.0X01.0X03 add enum_frame_interval function. + */ + + #include +@@ -23,7 +24,7 @@ + #include + #include + +-#define DRIVER_VERSION KERNEL_VERSION(0, 0x01, 0x2) ++#define DRIVER_VERSION KERNEL_VERSION(0, 0x01, 0x3) + + #ifndef V4L2_CID_DIGITAL_GAIN + #define V4L2_CID_DIGITAL_GAIN V4L2_CID_GAIN +@@ -92,7 +93,7 @@ struct regval { + struct ov9281_mode { + u32 width; + u32 height; +- u32 max_fps; ++ struct v4l2_fract max_fps; + u32 hts_def; + u32 vts_def; + u32 exp_def; +@@ -246,7 +247,10 @@ static const struct ov9281_mode supporte + { + .width = 1280, + .height = 800, +- .max_fps = 120, ++ .max_fps = { ++ .numerator = 10000, ++ .denominator = 1200000, ++ }, + .exp_def = 0x0320, + .hts_def = 0x0b60,//0x2d8*4 + .vts_def = 0x038e, +@@ -483,8 +487,7 @@ static int OV9281_g_frame_interval(struc + const struct ov9281_mode *mode = ov9281->cur_mode; + + mutex_lock(&ov9281->mutex); +- fi->interval.numerator = 10000; +- fi->interval.denominator = mode->max_fps * 10000; ++ fi->interval = mode->max_fps; + mutex_unlock(&ov9281->mutex); + + return 0; +@@ -778,6 +781,23 @@ static int ov9281_open(struct v4l2_subde + } + #endif + ++static int ++ov9281_enum_frame_interval(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_frame_interval_enum *fie) ++{ ++ if (fie->index >= ARRAY_SIZE(supported_modes)) ++ return -EINVAL; ++ ++ if (fie->code != MEDIA_BUS_FMT_Y10_1X10) ++ return -EINVAL; ++ ++ fie->width = supported_modes[fie->index].width; ++ fie->height = supported_modes[fie->index].height; ++ fie->interval = supported_modes[fie->index].max_fps; ++ return 0; ++} ++ + static const struct dev_pm_ops ov9281_pm_ops = { + SET_RUNTIME_PM_OPS(ov9281_runtime_suspend, + ov9281_runtime_resume, NULL) +@@ -805,6 +825,7 @@ static const struct v4l2_subdev_video_op + static const struct v4l2_subdev_pad_ops ov9281_pad_ops = { + .enum_mbus_code = ov9281_enum_mbus_code, + .enum_frame_size = ov9281_enum_frame_sizes, ++ .enum_frame_interval = ov9281_enum_frame_interval, + .get_fmt = ov9281_get_fmt, + .set_fmt = ov9281_set_fmt, + }; diff --git a/target/linux/bcm27xx/patches-5.10/950-0287-media-i2c-ov9281-Fixup-for-recent-kernel-releases-an.patch b/target/linux/bcm27xx/patches-5.10/950-0287-media-i2c-ov9281-Fixup-for-recent-kernel-releases-an.patch new file mode 100644 index 0000000000..5e09d99ff9 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0287-media-i2c-ov9281-Fixup-for-recent-kernel-releases-an.patch @@ -0,0 +1,681 @@ +From a73ced40f7ca1b0735e5d0d1c45087e02023a618 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 14 Apr 2020 16:12:33 +0100 +Subject: [PATCH] media: i2c: ov9281: Fixup for recent kernel releases, + and remove custom code + +The Rockchip driver was based on a 4.4 kernel, and had several custom +Rockchip parts. + +Update to 5.4 kernel APIs, with the relevant controls required by +libcamera, and remove custom Rockchip parts. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov9281.c | 361 +++++++++++++------------------------ + 1 file changed, 122 insertions(+), 239 deletions(-) + +--- a/drivers/media/i2c/ov9281.c ++++ b/drivers/media/i2c/ov9281.c +@@ -1,6 +1,11 @@ + // SPDX-License-Identifier: GPL-2.0 + /* +- * ov9281 driver ++ * Omnivision OV9281 1280x800 global shutter image sensor driver ++ * ++ * This driver has been taken from ++ * https://github.com/rockchip-linux/kernel/blob/develop-4.4/drivers/media/i2c/ov9281.c ++ * cleaned up, made to compile against mainline kernels instead of the Rockchip ++ * vendor kernel, and the relevant controls added to work with libcamera. + * + * Copyright (C) 2017 Fuzhou Rockchip Electronics Co., Ltd. + * V0.0X01.0X02 fix mclk issue when probe multiple camera. +@@ -17,22 +22,18 @@ + #include + #include + #include +-#include + #include + #include + #include + #include +-#include +- +-#define DRIVER_VERSION KERNEL_VERSION(0, 0x01, 0x3) +- +-#ifndef V4L2_CID_DIGITAL_GAIN +-#define V4L2_CID_DIGITAL_GAIN V4L2_CID_GAIN +-#endif + + #define OV9281_LINK_FREQ_400MHZ 400000000 ++#define OV9281_LANES 2 ++#define OV9281_BITS_PER_SAMPLE 10 ++ + /* pixel rate = link frequency * 2 * lanes / BITS_PER_SAMPLE */ +-#define OV9281_PIXEL_RATE (OV9281_LINK_FREQ_400MHZ * 2 * 2 / 10) ++#define OV9281_PIXEL_RATE (OV9281_LINK_FREQ_400MHZ * 2 * \ ++ OV9281_LANES / OV9281_BITS_PER_SAMPLE) + #define OV9281_XVCLK_FREQ 24000000 + + #define CHIP_ID 0x9281 +@@ -63,18 +64,24 @@ + + #define OV9281_REG_VTS 0x380e + ++/* ++ * OV9281 native and active pixel array size. ++ * Datasheet not available to confirm these values, so assume there are no ++ * border pixels. ++ */ ++#define OV9281_NATIVE_WIDTH 1280U ++#define OV9281_NATIVE_HEIGHT 800U ++#define OV9281_PIXEL_ARRAY_LEFT 0U ++#define OV9281_PIXEL_ARRAY_TOP 0U ++#define OV9281_PIXEL_ARRAY_WIDTH 1280U ++#define OV9281_PIXEL_ARRAY_HEIGHT 800U ++ + #define REG_NULL 0xFFFF + + #define OV9281_REG_VALUE_08BIT 1 + #define OV9281_REG_VALUE_16BIT 2 + #define OV9281_REG_VALUE_24BIT 3 + +-#define OV9281_LANES 2 +-#define OV9281_BITS_PER_SAMPLE 10 +- +-#define OF_CAMERA_PINCTRL_STATE_DEFAULT "rockchip,camera_default" +-#define OF_CAMERA_PINCTRL_STATE_SLEEP "rockchip,camera_sleep" +- + #define OV9281_NAME "ov9281" + + static const char * const ov9281_supply_names[] = { +@@ -93,10 +100,10 @@ struct regval { + struct ov9281_mode { + u32 width; + u32 height; +- struct v4l2_fract max_fps; + u32 hts_def; + u32 vts_def; + u32 exp_def; ++ struct v4l2_rect crop; + const struct regval *reg_list; + }; + +@@ -107,10 +114,6 @@ struct ov9281 { + struct gpio_desc *pwdn_gpio; + struct regulator_bulk_data supplies[OV9281_NUM_SUPPLIES]; + +- struct pinctrl *pinctrl; +- struct pinctrl_state *pins_default; +- struct pinctrl_state *pins_sleep; +- + struct v4l2_subdev subdev; + struct media_pad pad; + struct v4l2_ctrl_handler ctrl_handler; +@@ -124,23 +127,12 @@ struct ov9281 { + bool streaming; + bool power_on; + const struct ov9281_mode *cur_mode; +- u32 module_index; +- const char *module_facing; +- const char *module_name; +- const char *len_name; + }; + + #define to_ov9281(sd) container_of(sd, struct ov9281, subdev) + + /* + * Xclk 24Mhz +- */ +-static const struct regval ov9281_global_regs[] = { +- {REG_NULL, 0x00}, +-}; +- +-/* +- * Xclk 24Mhz + * max_framerate 120fps + * mipi_datarate per lane 800Mbps + */ +@@ -247,13 +239,15 @@ static const struct ov9281_mode supporte + { + .width = 1280, + .height = 800, +- .max_fps = { +- .numerator = 10000, +- .denominator = 1200000, +- }, + .exp_def = 0x0320, +- .hts_def = 0x0b60,//0x2d8*4 ++ .hts_def = 0x05b0, /* 0x2d8*2 */ + .vts_def = 0x038e, ++ .crop = { ++ .left = 0, ++ .top = 0, ++ .width = 1280, ++ .height = 800 ++ }, + .reg_list = ov9281_1280x800_regs, + }, + }; +@@ -389,22 +383,28 @@ static int ov9281_set_fmt(struct v4l2_su + fmt->format.width = mode->width; + fmt->format.height = mode->height; + fmt->format.field = V4L2_FIELD_NONE; ++ fmt->format.colorspace = V4L2_COLORSPACE_SRGB; ++ fmt->format.ycbcr_enc = ++ V4L2_MAP_YCBCR_ENC_DEFAULT(fmt->format.colorspace); ++ fmt->format.quantization = ++ V4L2_MAP_QUANTIZATION_DEFAULT(true, fmt->format.colorspace, ++ fmt->format.ycbcr_enc); ++ fmt->format.xfer_func = ++ V4L2_MAP_XFER_FUNC_DEFAULT(fmt->format.colorspace); ++ + if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { +-#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API + *v4l2_subdev_get_try_format(sd, cfg, fmt->pad) = fmt->format; +-#else +- mutex_unlock(&ov9281->mutex); +- return -ENOTTY; +-#endif + } else { + ov9281->cur_mode = mode; + h_blank = mode->hts_def - mode->width; + __v4l2_ctrl_modify_range(ov9281->hblank, h_blank, + h_blank, 1, h_blank); ++ __v4l2_ctrl_s_ctrl(ov9281->hblank, h_blank); + vblank_def = mode->vts_def - mode->height; + __v4l2_ctrl_modify_range(ov9281->vblank, vblank_def, + OV9281_VTS_MAX - mode->height, + 1, vblank_def); ++ __v4l2_ctrl_s_ctrl(ov9281->vblank, vblank_def); + } + + mutex_unlock(&ov9281->mutex); +@@ -421,17 +421,21 @@ static int ov9281_get_fmt(struct v4l2_su + + mutex_lock(&ov9281->mutex); + if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { +-#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API + fmt->format = *v4l2_subdev_get_try_format(sd, cfg, fmt->pad); +-#else +- mutex_unlock(&ov9281->mutex); +- return -ENOTTY; +-#endif + } else { + fmt->format.width = mode->width; + fmt->format.height = mode->height; + fmt->format.code = MEDIA_BUS_FMT_Y10_1X10; + fmt->format.field = V4L2_FIELD_NONE; ++ fmt->format.colorspace = V4L2_COLORSPACE_SRGB; ++ fmt->format.ycbcr_enc = ++ V4L2_MAP_YCBCR_ENC_DEFAULT(fmt->format.colorspace); ++ fmt->format.quantization = ++ V4L2_MAP_QUANTIZATION_DEFAULT(true, ++ fmt->format.colorspace, ++ fmt->format.ycbcr_enc); ++ fmt->format.xfer_func = ++ V4L2_MAP_XFER_FUNC_DEFAULT(fmt->format.colorspace); + } + mutex_unlock(&ov9281->mutex); + +@@ -442,7 +446,7 @@ static int ov9281_enum_mbus_code(struct + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_mbus_code_enum *code) + { +- if (code->index != 0) ++ if (code->index) + return -EINVAL; + code->code = MEDIA_BUS_FMT_Y10_1X10; + +@@ -480,88 +484,56 @@ static int ov9281_enable_test_pattern(st + OV9281_REG_VALUE_08BIT, val); + } + +-static int OV9281_g_frame_interval(struct v4l2_subdev *sd, +- struct v4l2_subdev_frame_interval *fi) +-{ +- struct ov9281 *ov9281 = to_ov9281(sd); +- const struct ov9281_mode *mode = ov9281->cur_mode; +- +- mutex_lock(&ov9281->mutex); +- fi->interval = mode->max_fps; +- mutex_unlock(&ov9281->mutex); ++static const struct v4l2_rect * ++__ov9281_get_pad_crop(struct ov9281 *ov9281, struct v4l2_subdev_pad_config *cfg, ++ unsigned int pad, enum v4l2_subdev_format_whence which) ++{ ++ switch (which) { ++ case V4L2_SUBDEV_FORMAT_TRY: ++ return v4l2_subdev_get_try_crop(&ov9281->subdev, cfg, pad); ++ case V4L2_SUBDEV_FORMAT_ACTIVE: ++ return &ov9281->cur_mode->crop; ++ } + +- return 0; ++ return NULL; + } + +-static void ov9281_get_module_inf(struct ov9281 *ov9281, +- struct rkmodule_inf *inf) ++static int ov9281_get_selection(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_selection *sel) + { +- memset(inf, 0, sizeof(*inf)); +- strlcpy(inf->base.sensor, OV9281_NAME, sizeof(inf->base.sensor)); +- strlcpy(inf->base.module, ov9281->module_name, +- sizeof(inf->base.module)); +- strlcpy(inf->base.lens, ov9281->len_name, sizeof(inf->base.lens)); +-} ++ switch (sel->target) { ++ case V4L2_SEL_TGT_CROP: { ++ struct ov9281 *ov9281 = to_ov9281(sd); + +-static long ov9281_ioctl(struct v4l2_subdev *sd, unsigned int cmd, void *arg) +-{ +- struct ov9281 *ov9281 = to_ov9281(sd); +- long ret = 0; ++ mutex_lock(&ov9281->mutex); ++ sel->r = *__ov9281_get_pad_crop(ov9281, cfg, sel->pad, ++ sel->which); ++ mutex_unlock(&ov9281->mutex); + +- switch (cmd) { +- case RKMODULE_GET_MODULE_INFO: +- ov9281_get_module_inf(ov9281, (struct rkmodule_inf *)arg); +- break; +- default: +- ret = -ENOIOCTLCMD; +- break; ++ return 0; + } + +- return ret; +-} ++ case V4L2_SEL_TGT_NATIVE_SIZE: ++ sel->r.top = 0; ++ sel->r.left = 0; ++ sel->r.width = OV9281_NATIVE_WIDTH; ++ sel->r.height = OV9281_NATIVE_HEIGHT; + +-#ifdef CONFIG_COMPAT +-static long ov9281_compat_ioctl32(struct v4l2_subdev *sd, +- unsigned int cmd, unsigned long arg) +-{ +- void __user *up = compat_ptr(arg); +- struct rkmodule_inf *inf; +- struct rkmodule_awb_cfg *cfg; +- long ret; +- +- switch (cmd) { +- case RKMODULE_GET_MODULE_INFO: +- inf = kzalloc(sizeof(*inf), GFP_KERNEL); +- if (!inf) { +- ret = -ENOMEM; +- return ret; +- } ++ return 0; + +- ret = ov9281_ioctl(sd, cmd, inf); +- if (!ret) +- ret = copy_to_user(up, inf, sizeof(*inf)); +- kfree(inf); +- break; +- case RKMODULE_AWB_CFG: +- cfg = kzalloc(sizeof(*cfg), GFP_KERNEL); +- if (!cfg) { +- ret = -ENOMEM; +- return ret; +- } ++ case V4L2_SEL_TGT_CROP_DEFAULT: ++ case V4L2_SEL_TGT_CROP_BOUNDS: ++ sel->r.top = OV9281_PIXEL_ARRAY_TOP; ++ sel->r.left = OV9281_PIXEL_ARRAY_LEFT; ++ sel->r.width = OV9281_PIXEL_ARRAY_WIDTH; ++ sel->r.height = OV9281_PIXEL_ARRAY_HEIGHT; + +- ret = copy_from_user(cfg, up, sizeof(*cfg)); +- if (!ret) +- ret = ov9281_ioctl(sd, cmd, cfg); +- kfree(cfg); +- break; +- default: +- ret = -ENOIOCTLCMD; +- break; ++ return 0; + } + +- return ret; ++ return -EINVAL; + } +-#endif + + static int __ov9281_start_stream(struct ov9281 *ov9281) + { +@@ -643,12 +615,6 @@ static int ov9281_s_power(struct v4l2_su + pm_runtime_put_noidle(&client->dev); + goto unlock_and_return; + } +- ret = ov9281_write_array(ov9281->client, ov9281_global_regs); +- if (ret) { +- v4l2_err(sd, "could not set init registers\n"); +- pm_runtime_put_noidle(&client->dev); +- goto unlock_and_return; +- } + ov9281->power_on = true; + } else { + pm_runtime_put(&client->dev); +@@ -673,18 +639,12 @@ static int __ov9281_power_on(struct ov92 + u32 delay_us; + struct device *dev = &ov9281->client->dev; + +- if (!IS_ERR_OR_NULL(ov9281->pins_default)) { +- ret = pinctrl_select_state(ov9281->pinctrl, +- ov9281->pins_default); +- if (ret < 0) +- dev_err(dev, "could not set pins\n"); +- } +- + ret = clk_set_rate(ov9281->xvclk, OV9281_XVCLK_FREQ); + if (ret < 0) + dev_warn(dev, "Failed to set xvclk rate (24MHz)\n"); + if (clk_get_rate(ov9281->xvclk) != OV9281_XVCLK_FREQ) +- dev_warn(dev, "xvclk mismatched, modes are based on 24MHz\n"); ++ dev_warn(dev, "xvclk mismatched, modes are based on 24MHz - rate is %lu\n", ++ clk_get_rate(ov9281->xvclk)); + + ret = clk_prepare_enable(ov9281->xvclk); + if (ret < 0) { +@@ -722,20 +682,11 @@ disable_clk: + + static void __ov9281_power_off(struct ov9281 *ov9281) + { +- int ret; +- struct device *dev = &ov9281->client->dev; +- + if (!IS_ERR(ov9281->pwdn_gpio)) + gpiod_set_value_cansleep(ov9281->pwdn_gpio, 0); + clk_disable_unprepare(ov9281->xvclk); + if (!IS_ERR(ov9281->reset_gpio)) + gpiod_set_value_cansleep(ov9281->reset_gpio, 0); +- if (!IS_ERR_OR_NULL(ov9281->pins_sleep)) { +- ret = pinctrl_select_state(ov9281->pinctrl, +- ov9281->pins_sleep); +- if (ret < 0) +- dev_dbg(dev, "could not set pins\n"); +- } + regulator_bulk_disable(OV9281_NUM_SUPPLIES, ov9281->supplies); + } + +@@ -759,7 +710,6 @@ static int ov9281_runtime_suspend(struct + return 0; + } + +-#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API + static int ov9281_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) + { + struct ov9281 *ov9281 = to_ov9281(sd); +@@ -773,61 +723,42 @@ static int ov9281_open(struct v4l2_subde + try_fmt->height = def_mode->height; + try_fmt->code = MEDIA_BUS_FMT_Y10_1X10; + try_fmt->field = V4L2_FIELD_NONE; ++ try_fmt->colorspace = V4L2_COLORSPACE_SRGB; ++ try_fmt->ycbcr_enc = V4L2_MAP_YCBCR_ENC_DEFAULT(try_fmt->colorspace); ++ try_fmt->quantization = ++ V4L2_MAP_QUANTIZATION_DEFAULT(true, try_fmt->colorspace, ++ try_fmt->ycbcr_enc); ++ try_fmt->xfer_func = V4L2_MAP_XFER_FUNC_DEFAULT(try_fmt->colorspace); + + mutex_unlock(&ov9281->mutex); + /* No crop or compose */ + + return 0; + } +-#endif +- +-static int +-ov9281_enum_frame_interval(struct v4l2_subdev *sd, +- struct v4l2_subdev_pad_config *cfg, +- struct v4l2_subdev_frame_interval_enum *fie) +-{ +- if (fie->index >= ARRAY_SIZE(supported_modes)) +- return -EINVAL; +- +- if (fie->code != MEDIA_BUS_FMT_Y10_1X10) +- return -EINVAL; +- +- fie->width = supported_modes[fie->index].width; +- fie->height = supported_modes[fie->index].height; +- fie->interval = supported_modes[fie->index].max_fps; +- return 0; +-} + + static const struct dev_pm_ops ov9281_pm_ops = { + SET_RUNTIME_PM_OPS(ov9281_runtime_suspend, + ov9281_runtime_resume, NULL) + }; + +-#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API + static const struct v4l2_subdev_internal_ops ov9281_internal_ops = { + .open = ov9281_open, + }; +-#endif + + static const struct v4l2_subdev_core_ops ov9281_core_ops = { + .s_power = ov9281_s_power, +- .ioctl = ov9281_ioctl, +-#ifdef CONFIG_COMPAT +- .compat_ioctl32 = ov9281_compat_ioctl32, +-#endif + }; + + static const struct v4l2_subdev_video_ops ov9281_video_ops = { + .s_stream = ov9281_s_stream, +- .g_frame_interval = OV9281_g_frame_interval, + }; + + static const struct v4l2_subdev_pad_ops ov9281_pad_ops = { + .enum_mbus_code = ov9281_enum_mbus_code, + .enum_frame_size = ov9281_enum_frame_sizes, +- .enum_frame_interval = ov9281_enum_frame_interval, + .get_fmt = ov9281_get_fmt, + .set_fmt = ov9281_set_fmt, ++ .get_selection = ov9281_get_selection, + }; + + static const struct v4l2_subdev_ops ov9281_subdev_ops = { +@@ -868,7 +799,8 @@ static int ov9281_set_ctrl(struct v4l2_c + case V4L2_CID_ANALOGUE_GAIN: + ret = ov9281_write_reg(ov9281->client, OV9281_REG_GAIN_H, + OV9281_REG_VALUE_08BIT, +- (ctrl->val >> OV9281_GAIN_H_SHIFT) & OV9281_GAIN_H_MASK); ++ (ctrl->val >> OV9281_GAIN_H_SHIFT) & ++ OV9281_GAIN_H_MASK); + ret |= ov9281_write_reg(ov9281->client, OV9281_REG_GAIN_L, + OV9281_REG_VALUE_08BIT, + ctrl->val & OV9281_GAIN_L_MASK); +@@ -922,31 +854,34 @@ static int ov9281_initialize_controls(st + + h_blank = mode->hts_def - mode->width; + ov9281->hblank = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK, +- h_blank, h_blank, 1, h_blank); ++ h_blank, h_blank, 1, h_blank); + if (ov9281->hblank) + ov9281->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY; + + vblank_def = mode->vts_def - mode->height; + ov9281->vblank = v4l2_ctrl_new_std(handler, &ov9281_ctrl_ops, +- V4L2_CID_VBLANK, vblank_def, +- OV9281_VTS_MAX - mode->height, +- 1, vblank_def); ++ V4L2_CID_VBLANK, vblank_def, ++ OV9281_VTS_MAX - mode->height, 1, ++ vblank_def); + + exposure_max = mode->vts_def - 4; + ov9281->exposure = v4l2_ctrl_new_std(handler, &ov9281_ctrl_ops, +- V4L2_CID_EXPOSURE, OV9281_EXPOSURE_MIN, +- exposure_max, OV9281_EXPOSURE_STEP, +- mode->exp_def); ++ V4L2_CID_EXPOSURE, ++ OV9281_EXPOSURE_MIN, exposure_max, ++ OV9281_EXPOSURE_STEP, ++ mode->exp_def); + + ov9281->anal_gain = v4l2_ctrl_new_std(handler, &ov9281_ctrl_ops, +- V4L2_CID_ANALOGUE_GAIN, OV9281_GAIN_MIN, +- OV9281_GAIN_MAX, OV9281_GAIN_STEP, +- OV9281_GAIN_DEFAULT); +- +- ov9281->test_pattern = v4l2_ctrl_new_std_menu_items(handler, +- &ov9281_ctrl_ops, V4L2_CID_TEST_PATTERN, +- ARRAY_SIZE(ov9281_test_pattern_menu) - 1, +- 0, 0, ov9281_test_pattern_menu); ++ V4L2_CID_ANALOGUE_GAIN, ++ OV9281_GAIN_MIN, OV9281_GAIN_MAX, ++ OV9281_GAIN_STEP, ++ OV9281_GAIN_DEFAULT); ++ ++ ov9281->test_pattern = ++ v4l2_ctrl_new_std_menu_items(handler, &ov9281_ctrl_ops, ++ V4L2_CID_TEST_PATTERN, ++ ARRAY_SIZE(ov9281_test_pattern_menu) - 1, ++ 0, 0, ov9281_test_pattern_menu); + + if (handler->error) { + ret = handler->error; +@@ -1000,34 +935,14 @@ static int ov9281_probe(struct i2c_clien + const struct i2c_device_id *id) + { + struct device *dev = &client->dev; +- struct device_node *node = dev->of_node; + struct ov9281 *ov9281; + struct v4l2_subdev *sd; +- char facing[2]; + int ret; + +- dev_info(dev, "driver version: %02x.%02x.%02x", +- DRIVER_VERSION >> 16, +- (DRIVER_VERSION & 0xff00) >> 8, +- DRIVER_VERSION & 0x00ff); +- + ov9281 = devm_kzalloc(dev, sizeof(*ov9281), GFP_KERNEL); + if (!ov9281) + return -ENOMEM; + +- ret = of_property_read_u32(node, RKMODULE_CAMERA_MODULE_INDEX, +- &ov9281->module_index); +- ret |= of_property_read_string(node, RKMODULE_CAMERA_MODULE_FACING, +- &ov9281->module_facing); +- ret |= of_property_read_string(node, RKMODULE_CAMERA_MODULE_NAME, +- &ov9281->module_name); +- ret |= of_property_read_string(node, RKMODULE_CAMERA_LENS_NAME, +- &ov9281->len_name); +- if (ret) { +- dev_err(dev, "could not get module information!\n"); +- return -EINVAL; +- } +- + ov9281->client = client; + ov9281->cur_mode = &supported_modes[0]; + +@@ -1037,31 +952,15 @@ static int ov9281_probe(struct i2c_clien + return -EINVAL; + } + +- ov9281->reset_gpio = devm_gpiod_get(dev, "reset", GPIOD_OUT_LOW); ++ ov9281->reset_gpio = devm_gpiod_get_optional(dev, "reset", ++ GPIOD_OUT_LOW); + if (IS_ERR(ov9281->reset_gpio)) + dev_warn(dev, "Failed to get reset-gpios\n"); + +- ov9281->pwdn_gpio = devm_gpiod_get(dev, "pwdn", GPIOD_OUT_LOW); ++ ov9281->pwdn_gpio = devm_gpiod_get_optional(dev, "pwdn", GPIOD_OUT_LOW); + if (IS_ERR(ov9281->pwdn_gpio)) + dev_warn(dev, "Failed to get pwdn-gpios\n"); + +- ov9281->pinctrl = devm_pinctrl_get(dev); +- if (!IS_ERR(ov9281->pinctrl)) { +- ov9281->pins_default = +- pinctrl_lookup_state(ov9281->pinctrl, +- OF_CAMERA_PINCTRL_STATE_DEFAULT); +- if (IS_ERR(ov9281->pins_default)) +- dev_err(dev, "could not get default pinstate\n"); +- +- ov9281->pins_sleep = +- pinctrl_lookup_state(ov9281->pinctrl, +- OF_CAMERA_PINCTRL_STATE_SLEEP); +- if (IS_ERR(ov9281->pins_sleep)) +- dev_err(dev, "could not get sleep pinstate\n"); +- } else { +- dev_err(dev, "no pinctrl\n"); +- } +- + ret = ov9281_configure_regulators(ov9281); + if (ret) { + dev_err(dev, "Failed to get power regulators\n"); +@@ -1084,26 +983,16 @@ static int ov9281_probe(struct i2c_clien + if (ret) + goto err_power_off; + +-#ifdef CONFIG_VIDEO_V4L2_SUBDEV_API + sd->internal_ops = &ov9281_internal_ops; + sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; +-#endif +-#if defined(CONFIG_MEDIA_CONTROLLER) ++ + ov9281->pad.flags = MEDIA_PAD_FL_SOURCE; +- sd->entity.type = MEDIA_ENT_T_V4L2_SUBDEV_SENSOR; +- ret = media_entity_init(&sd->entity, 1, &ov9281->pad, 0); ++ sd->entity.function = MEDIA_ENT_F_CAM_SENSOR; ++ ret = media_entity_pads_init(&sd->entity, 1, &ov9281->pad); + if (ret < 0) + goto err_power_off; +-#endif +- +- memset(facing, 0, sizeof(facing)); +- if (strcmp(ov9281->module_facing, "back") == 0) +- facing[0] = 'b'; +- else +- facing[0] = 'f'; + +- snprintf(sd->name, sizeof(sd->name), "m%02d_%s_%s %s", +- ov9281->module_index, facing, ++ snprintf(sd->name, sizeof(sd->name), "m%s %s", + OV9281_NAME, dev_name(sd->dev)); + ret = v4l2_async_register_subdev_sensor_common(sd); + if (ret) { +@@ -1118,9 +1007,7 @@ static int ov9281_probe(struct i2c_clien + return 0; + + err_clean_entity: +-#if defined(CONFIG_MEDIA_CONTROLLER) + media_entity_cleanup(&sd->entity); +-#endif + err_power_off: + __ov9281_power_off(ov9281); + err_free_handler: +@@ -1137,9 +1024,7 @@ static int ov9281_remove(struct i2c_clie + struct ov9281 *ov9281 = to_ov9281(sd); + + v4l2_async_unregister_subdev(sd); +-#if defined(CONFIG_MEDIA_CONTROLLER) + media_entity_cleanup(&sd->entity); +-#endif + v4l2_ctrl_handler_free(&ov9281->ctrl_handler); + mutex_destroy(&ov9281->mutex); + +@@ -1151,13 +1036,11 @@ static int ov9281_remove(struct i2c_clie + return 0; + } + +-#if IS_ENABLED(CONFIG_OF) + static const struct of_device_id ov9281_of_match[] = { + { .compatible = "ovti,ov9281" }, + {}, + }; + MODULE_DEVICE_TABLE(of, ov9281_of_match); +-#endif + + static const struct i2c_device_id ov9281_match_id[] = { + { "ovti,ov9281", 0 }, diff --git a/target/linux/bcm27xx/patches-5.10/950-0288-media-i2c-ov9281-Read-chip-ID-via-2-reads.patch b/target/linux/bcm27xx/patches-5.10/950-0288-media-i2c-ov9281-Read-chip-ID-via-2-reads.patch new file mode 100644 index 0000000000..185fb77f5c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0288-media-i2c-ov9281-Read-chip-ID-via-2-reads.patch @@ -0,0 +1,42 @@ +From e5bf123ed1069795286e5caa8f2a67bb5977691c Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Mon, 6 Jul 2020 17:51:32 +0100 +Subject: [PATCH] media: i2c: ov9281: Read chip ID via 2 reads + +Vision Components have made an OV9281 module which blocks reading +back the majority of registers to comply with NDAs, and in doing +so doesn't allow auto-increment register reading as used when +reading the chip ID. + +Use two reads and manually combine the results. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov9281.c | 14 +++++++++----- + 1 file changed, 9 insertions(+), 5 deletions(-) + +--- a/drivers/media/i2c/ov9281.c ++++ b/drivers/media/i2c/ov9281.c +@@ -904,13 +904,17 @@ static int ov9281_check_sensor_id(struct + struct i2c_client *client) + { + struct device *dev = &ov9281->client->dev; +- u32 id = 0; ++ u32 id = 0, id_msb; + int ret; + +- ret = ov9281_read_reg(client, OV9281_REG_CHIP_ID, +- OV9281_REG_VALUE_16BIT, &id); +- if (id != CHIP_ID) { +- dev_err(dev, "Unexpected sensor id(%06x), ret(%d)\n", id, ret); ++ ret = ov9281_read_reg(client, OV9281_REG_CHIP_ID + 1, ++ OV9281_REG_VALUE_08BIT, &id); ++ if (!ret) ++ ret = ov9281_read_reg(client, OV9281_REG_CHIP_ID, ++ OV9281_REG_VALUE_08BIT, &id_msb); ++ id |= (id_msb << 8); ++ if (ret || id != CHIP_ID) { ++ dev_err(dev, "Unexpected sensor id(%04x), ret(%d)\n", id, ret); + return -ENODEV; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0289-media-i2c-imx290-Explicitly-set-v-h-blank-on-mode-ch.patch b/target/linux/bcm27xx/patches-5.10/950-0289-media-i2c-imx290-Explicitly-set-v-h-blank-on-mode-ch.patch new file mode 100644 index 0000000000..bdcf9005b5 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0289-media-i2c-imx290-Explicitly-set-v-h-blank-on-mode-ch.patch @@ -0,0 +1,46 @@ +From f7ff6542ad9cdee4a1e67a0243f7dcc93cceb08a Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 7 Jul 2020 10:31:53 +0100 +Subject: [PATCH] media: i2c: imx290: Explicitly set v&h blank on mode + change + +__v4l2_ctrl_modify_range only updates the current value should +it be invalid within the new range. That can leave modes producing +odd frame rates. + +Explicitly update the HBLANK and VBLANK values so that on mode +change we revert to the default frame rate for the mode. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/imx290.c | 10 ++++++++-- + 1 file changed, 8 insertions(+), 2 deletions(-) + +--- a/drivers/media/i2c/imx290.c ++++ b/drivers/media/i2c/imx290.c +@@ -796,17 +796,23 @@ static int imx290_set_fmt(struct v4l2_su + __v4l2_ctrl_s_ctrl_int64(imx290->pixel_rate, + imx290_calc_pixel_rate(imx290)); + +- if (imx290->hblank) ++ if (imx290->hblank) { + __v4l2_ctrl_modify_range(imx290->hblank, + imx290->hmax_min - mode->width, + IMX290_HMAX_MAX - mode->width, + 1, mode->hmax - mode->width); +- if (imx290->vblank) ++ __v4l2_ctrl_s_ctrl(imx290->hblank, ++ mode->hmax - mode->width); ++ } ++ if (imx290->vblank) { + __v4l2_ctrl_modify_range(imx290->vblank, + mode->vmax - mode->height, + IMX290_VMAX_MAX - mode->height, + 1, + mode->vmax - mode->height); ++ __v4l2_ctrl_s_ctrl(imx290->vblank, ++ mode->vmax - mode->height); ++ } + if (imx290->exposure) + __v4l2_ctrl_modify_range(imx290->exposure, + mode->vmax - mode->height, diff --git a/target/linux/bcm27xx/patches-5.10/950-0290-media-i2c-imx290-Add-support-for-g_selection-to-repo.patch b/target/linux/bcm27xx/patches-5.10/950-0290-media-i2c-imx290-Add-support-for-g_selection-to-repo.patch new file mode 100644 index 0000000000..17798e50b7 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0290-media-i2c-imx290-Add-support-for-g_selection-to-repo.patch @@ -0,0 +1,156 @@ +From ee95eb32c4202a2d290af6c754806ef3bdfb3fda Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 7 Jul 2020 11:23:48 +0100 +Subject: [PATCH] media: i2c: imx290: Add support for g_selection to + report cropping + +Userspace needs to know the cropping arrangements for each mode, +so expose this through g_selection. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/imx290.c | 84 ++++++++++++++++++++++++++++++++++++++ + 1 file changed, 84 insertions(+) + +--- a/drivers/media/i2c/imx290.c ++++ b/drivers/media/i2c/imx290.c +@@ -61,6 +61,13 @@ enum imx290_clk_index { + #define IMX290_PGCTRL_THRU BIT(1) + #define IMX290_PGCTRL_MODE(n) ((n) << 4) + ++#define IMX290_NATIVE_WIDTH 1945U ++#define IMX290_NATIVE_HEIGHT 1109U ++#define IMX290_PIXEL_ARRAY_LEFT 4U ++#define IMX290_PIXEL_ARRAY_TOP 12U ++#define IMX290_PIXEL_ARRAY_WIDTH 1937U ++#define IMX290_PIXEL_ARRAY_HEIGHT 1097U ++ + static const char * const imx290_supply_name[] = { + "vdda", + "vddd", +@@ -80,6 +87,7 @@ struct imx290_mode { + u32 hmax; + u32 vmax; + u8 link_freq_index; ++ struct v4l2_rect crop; + + const struct imx290_regval *data; + u32 data_size; +@@ -384,6 +392,12 @@ static const struct imx290_mode imx290_m + .hmax = 0x1130, + .vmax = 0x0465, + .link_freq_index = FREQ_INDEX_1080P, ++ .crop = { ++ .left = 4 + 8, ++ .top = 12 + 8, ++ .width = 1920, ++ .height = 1080, ++ }, + .data = imx290_1080p_settings, + .data_size = ARRAY_SIZE(imx290_1080p_settings), + .clk_data = { +@@ -398,6 +412,12 @@ static const struct imx290_mode imx290_m + .hmax = 0x19c8, + .vmax = 0x02ee, + .link_freq_index = FREQ_INDEX_720P, ++ .crop = { ++ .left = 4 + 8 + 320, ++ .top = 12 + 8 + 180, ++ .width = 1280, ++ .height = 720, ++ }, + .data = imx290_720p_settings, + .data_size = ARRAY_SIZE(imx290_720p_settings), + .clk_data = { +@@ -415,6 +435,12 @@ static const struct imx290_mode imx290_m + .hmax = 0x0898, + .vmax = 0x0465, + .link_freq_index = FREQ_INDEX_1080P, ++ .crop = { ++ .left = 4 + 8, ++ .top = 12 + 8, ++ .width = 1920, ++ .height = 1080, ++ }, + .data = imx290_1080p_settings, + .data_size = ARRAY_SIZE(imx290_1080p_settings), + .clk_data = { +@@ -429,6 +455,12 @@ static const struct imx290_mode imx290_m + .hmax = 0x0ce4, + .vmax = 0x02ee, + .link_freq_index = FREQ_INDEX_720P, ++ .crop = { ++ .left = 4 + 8 + 320, ++ .top = 12 + 8 + 180, ++ .width = 1280, ++ .height = 720, ++ }, + .data = imx290_720p_settings, + .data_size = ARRAY_SIZE(imx290_720p_settings), + .clk_data = { +@@ -875,6 +907,57 @@ static int imx290_write_current_format(s + return 0; + } + ++static const struct v4l2_rect * ++__imx290_get_pad_crop(struct imx290 *imx290, struct v4l2_subdev_pad_config *cfg, ++ unsigned int pad, enum v4l2_subdev_format_whence which) ++{ ++ switch (which) { ++ case V4L2_SUBDEV_FORMAT_TRY: ++ return v4l2_subdev_get_try_crop(&imx290->sd, cfg, pad); ++ case V4L2_SUBDEV_FORMAT_ACTIVE: ++ return &imx290->current_mode->crop; ++ } ++ ++ return NULL; ++} ++ ++static int imx290_get_selection(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_selection *sel) ++{ ++ switch (sel->target) { ++ case V4L2_SEL_TGT_CROP: { ++ struct imx290 *imx290 = to_imx290(sd); ++ ++ mutex_lock(&imx290->lock); ++ sel->r = *__imx290_get_pad_crop(imx290, cfg, sel->pad, ++ sel->which); ++ mutex_unlock(&imx290->lock); ++ ++ return 0; ++ } ++ ++ case V4L2_SEL_TGT_NATIVE_SIZE: ++ sel->r.top = 0; ++ sel->r.left = 0; ++ sel->r.width = IMX290_NATIVE_WIDTH; ++ sel->r.height = IMX290_NATIVE_HEIGHT; ++ ++ return 0; ++ ++ case V4L2_SEL_TGT_CROP_DEFAULT: ++ case V4L2_SEL_TGT_CROP_BOUNDS: ++ sel->r.top = IMX290_PIXEL_ARRAY_TOP; ++ sel->r.left = IMX290_PIXEL_ARRAY_LEFT; ++ sel->r.width = IMX290_PIXEL_ARRAY_WIDTH; ++ sel->r.height = IMX290_PIXEL_ARRAY_HEIGHT; ++ ++ return 0; ++ } ++ ++ return -EINVAL; ++} ++ + /* Start streaming */ + static int imx290_start_streaming(struct imx290 *imx290) + { +@@ -1073,6 +1156,7 @@ static const struct v4l2_subdev_pad_ops + .enum_frame_size = imx290_enum_frame_size, + .get_fmt = imx290_get_fmt, + .set_fmt = imx290_set_fmt, ++ .get_selection = imx290_get_selection, + }; + + static const struct v4l2_subdev_ops imx290_subdev_ops = { diff --git a/target/linux/bcm27xx/patches-5.10/950-0291-media-i2c-imx290-Set-the-colorspace-fields-in-the-fo.patch b/target/linux/bcm27xx/patches-5.10/950-0291-media-i2c-imx290-Set-the-colorspace-fields-in-the-fo.patch new file mode 100644 index 0000000000..6cca04ae4d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0291-media-i2c-imx290-Set-the-colorspace-fields-in-the-fo.patch @@ -0,0 +1,31 @@ +From b6eaf8158d0e2053680dc72e45d2a4e7d0617312 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 7 Jul 2020 11:51:26 +0100 +Subject: [PATCH] media: i2c: imx290: Set the colorspace fields in the + format + +The colorspace fields were left untouched in imx290_set_fmt +which lead to a v4l2-compliance failure. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/imx290.c | 8 ++++++++ + 1 file changed, 8 insertions(+) + +--- a/drivers/media/i2c/imx290.c ++++ b/drivers/media/i2c/imx290.c +@@ -813,6 +813,14 @@ static int imx290_set_fmt(struct v4l2_su + + fmt->format.code = imx290->formats[i].code; + fmt->format.field = V4L2_FIELD_NONE; ++ fmt->format.colorspace = V4L2_COLORSPACE_SRGB; ++ fmt->format.ycbcr_enc = ++ V4L2_MAP_YCBCR_ENC_DEFAULT(fmt->format.colorspace); ++ fmt->format.quantization = ++ V4L2_MAP_QUANTIZATION_DEFAULT(true, fmt->format.colorspace, ++ fmt->format.ycbcr_enc); ++ fmt->format.xfer_func = ++ V4L2_MAP_XFER_FUNC_DEFAULT(fmt->format.colorspace); + + if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { + format = v4l2_subdev_get_try_format(sd, cfg, fmt->pad); diff --git a/target/linux/bcm27xx/patches-5.10/950-0292-media-bcm2835-unicam-Reinstate-V4L2_CAP_READWRITE-in.patch b/target/linux/bcm27xx/patches-5.10/950-0292-media-bcm2835-unicam-Reinstate-V4L2_CAP_READWRITE-in.patch new file mode 100644 index 0000000000..abc33dcd32 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0292-media-bcm2835-unicam-Reinstate-V4L2_CAP_READWRITE-in.patch @@ -0,0 +1,28 @@ +From 615ab5f76328d089d64d46ea0676efe407e6b9c5 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 7 Jul 2020 14:23:40 +0100 +Subject: [PATCH] media: bcm2835-unicam: Reinstate V4L2_CAP_READWRITE + in the caps + +v4l2-compliance throws a failure if the device doesn't advertise +V4L2_CAP_READWRITE but allows read or write operations. +We do support read, so reinstate the flag. + +Signed-off-by: Dave Stevenson +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 4 ++-- + 1 file changed, 2 insertions(+), 2 deletions(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -2418,8 +2418,8 @@ static int register_node(struct unicam_d + vdev->queue = q; + vdev->lock = &node->lock; + vdev->device_caps = (pad_id == IMAGE_PAD) ? +- (V4L2_CAP_VIDEO_CAPTURE | V4L2_CAP_STREAMING) : +- (V4L2_CAP_META_CAPTURE | V4L2_CAP_STREAMING); ++ V4L2_CAP_VIDEO_CAPTURE : V4L2_CAP_META_CAPTURE; ++ vdev->device_caps |= V4L2_CAP_READWRITE | V4L2_CAP_STREAMING; + + /* Define the device names */ + snprintf(vdev->name, sizeof(vdev->name), "%s-%s", UNICAM_MODULE_NAME, diff --git a/target/linux/bcm27xx/patches-5.10/950-0293-media-bcm2835-unicam-Ensure-type-is-VIDEO_CAPTURE-in.patch b/target/linux/bcm27xx/patches-5.10/950-0293-media-bcm2835-unicam-Ensure-type-is-VIDEO_CAPTURE-in.patch new file mode 100644 index 0000000000..0645035f52 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0293-media-bcm2835-unicam-Ensure-type-is-VIDEO_CAPTURE-in.patch @@ -0,0 +1,36 @@ +From c1dc0c0bcda6de7374a46d99a73f855603d366a5 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 7 Jul 2020 14:52:43 +0100 +Subject: [PATCH] media: bcm2835-unicam: Ensure type is VIDEO_CAPTURE + in [g|s]_selection + +[g|s]_selection pass in a buffer type that needs to be validated +before passing on to the sensor subdev. + +Signed-off-by: Dave Stevenson +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 6 ++++++ + 1 file changed, 6 insertions(+) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -1885,6 +1885,9 @@ static int unicam_s_selection(struct fil + .r = sel->r, + }; + ++ if (sel->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) ++ return -EINVAL; ++ + return v4l2_subdev_call(dev->sensor, pad, set_selection, NULL, &sdsel); + } + +@@ -1899,6 +1902,9 @@ static int unicam_g_selection(struct fil + }; + int ret; + ++ if (sel->type != V4L2_BUF_TYPE_VIDEO_CAPTURE) ++ return -EINVAL; ++ + ret = v4l2_subdev_call(dev->sensor, pad, get_selection, NULL, &sdsel); + if (!ret) + sel->r = sdsel.r; diff --git a/target/linux/bcm27xx/patches-5.10/950-0294-media-bcm2835-unicam-Set-VPU-min-clock-freq-to-250Mh.patch b/target/linux/bcm27xx/patches-5.10/950-0294-media-bcm2835-unicam-Set-VPU-min-clock-freq-to-250Mh.patch new file mode 100644 index 0000000000..7fd337edb8 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0294-media-bcm2835-unicam-Set-VPU-min-clock-freq-to-250Mh.patch @@ -0,0 +1,127 @@ +From d839c8936020f393c5536d83b783198217243e8d Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Mon, 11 May 2020 13:02:22 +0100 +Subject: [PATCH] media: bcm2835: unicam: Set VPU min clock freq to + 250Mhz. + +When streaming with Unicam, the VPU must have a clock frequency of at +least 250Mhz. Otherwise, the input fifos could overrun, causing +image corruption. + +Signed-off-by: Naushir Patuck +--- + .../media/platform/bcm2835/bcm2835-unicam.c | 49 +++++++++++++++++-- + 1 file changed, 44 insertions(+), 5 deletions(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -89,6 +89,11 @@ MODULE_PARM_DESC(debug, "Debug level 0-3 + v4l2_err(&(dev)->v4l2_dev, fmt, ##arg) + + /* ++ * Unicam must request a minimum of 250Mhz from the VPU clock. ++ * Otherwise the input FIFOs overrun and cause image corruption. ++ */ ++#define MIN_VPU_CLOCK_RATE (250 * 1000 * 1000) ++/* + * To protect against a dodgy sensor driver never returning an error from + * enum_mbus_code, set a maximum index value to be used. + */ +@@ -417,8 +422,10 @@ struct unicam_device { + void __iomem *base; + /* clock gating base address */ + void __iomem *clk_gate_base; +- /* clock handle */ ++ /* lp clock handle */ + struct clk *clock; ++ /* vpu clock handle */ ++ struct clk *vpu_clock; + /* V4l2 device */ + struct v4l2_device v4l2_dev; + struct media_device mdev; +@@ -1678,16 +1685,28 @@ static int unicam_start_streaming(struct + unicam_dbg(1, dev, "Running with %u data lanes\n", + dev->active_data_lanes); + +- ret = clk_set_rate(dev->clock, 100 * 1000 * 1000); ++ ret = clk_set_min_rate(dev->vpu_clock, MIN_VPU_CLOCK_RATE); ++ if (ret) { ++ unicam_err(dev, "failed to set up VPU clock\n"); ++ goto err_pm_put; ++ } ++ ++ ret = clk_prepare_enable(dev->vpu_clock); + if (ret) { +- unicam_err(dev, "failed to set up clock\n"); ++ unicam_err(dev, "Failed to enable VPU clock: %d\n", ret); + goto err_pm_put; + } + ++ ret = clk_set_rate(dev->clock, 100 * 1000 * 1000); ++ if (ret) { ++ unicam_err(dev, "failed to set up CSI clock\n"); ++ goto err_vpu_clock; ++ } ++ + ret = clk_prepare_enable(dev->clock); + if (ret) { + unicam_err(dev, "Failed to enable CSI clock: %d\n", ret); +- goto err_pm_put; ++ goto err_vpu_clock; + } + + for (i = 0; i < ARRAY_SIZE(dev->node); i++) { +@@ -1721,6 +1740,11 @@ static int unicam_start_streaming(struct + err_disable_unicam: + unicam_disable(dev); + clk_disable_unprepare(dev->clock); ++err_vpu_clock: ++ ret = clk_set_min_rate(dev->vpu_clock, 0); ++ if (ret) ++ unicam_err(dev, "failed to reset the VPU clock\n"); ++ clk_disable_unprepare(dev->vpu_clock); + err_pm_put: + unicam_runtime_put(dev); + err_streaming: +@@ -1738,6 +1762,8 @@ static void unicam_stop_streaming(struct + node->streaming = false; + + if (node->pad_id == IMAGE_PAD) { ++ int ret; ++ + /* + * Stop streaming the sensor and disable the peripheral. + * We cannot continue streaming embedded data with the +@@ -1747,6 +1773,12 @@ static void unicam_stop_streaming(struct + unicam_err(dev, "stream off failed in subdev\n"); + + unicam_disable(dev); ++ ++ ret = clk_set_min_rate(dev->vpu_clock, 0); ++ if (ret) ++ unicam_err(dev, "failed to reset the min VPU clock\n"); ++ ++ clk_disable_unprepare(dev->vpu_clock); + clk_disable_unprepare(dev->clock); + unicam_runtime_put(dev); + +@@ -2750,11 +2782,18 @@ static int unicam_probe(struct platform_ + + unicam->clock = devm_clk_get(&pdev->dev, "lp"); + if (IS_ERR(unicam->clock)) { +- unicam_err(unicam, "Failed to get clock\n"); ++ unicam_err(unicam, "Failed to get lp clock\n"); + ret = PTR_ERR(unicam->clock); + goto err_unicam_put; + } + ++ unicam->vpu_clock = devm_clk_get(&pdev->dev, "vpu"); ++ if (IS_ERR(unicam->vpu_clock)) { ++ unicam_err(unicam, "Failed to get vpu clock\n"); ++ ret = PTR_ERR(unicam->vpu_clock); ++ goto err_unicam_put; ++ } ++ + ret = platform_get_irq(pdev, 0); + if (ret <= 0) { + dev_err(&pdev->dev, "No IRQ resource\n"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0295-dt-bindings-bcm2835-unicam-Update-documentation-with.patch b/target/linux/bcm27xx/patches-5.10/950-0295-dt-bindings-bcm2835-unicam-Update-documentation-with.patch new file mode 100644 index 0000000000..a2e8401a05 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0295-dt-bindings-bcm2835-unicam-Update-documentation-with.patch @@ -0,0 +1,38 @@ +From 45ae6757ee8379bc04e718591b23e45fae4c968c Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Mon, 11 May 2020 13:06:27 +0100 +Subject: [PATCH] dt-bindings: bcm2835-unicam: Update documentation + with new clock params + +Update the documentation to reflect the new "VPU" clock needed +by the bcm2835-unicam driver. + +Signed-off-by: Naushir Patuck +--- + .../devicetree/bindings/media/bcm2835-unicam.txt | 8 ++++---- + 1 file changed, 4 insertions(+), 4 deletions(-) + +--- a/Documentation/devicetree/bindings/media/bcm2835-unicam.txt ++++ b/Documentation/devicetree/bindings/media/bcm2835-unicam.txt +@@ -20,7 +20,7 @@ Required properties: + - interrupts : should contain the IRQ line for this Unicam instance. + - clocks : list of clock specifiers, corresponding to entries in + clock-names property. +-- clock-names : must contain an "lp" entry, matching entries in the ++- clock-names : must contain "lp" and "vpu" entries, matching entries in the + clocks property. + + Unicam supports a single port node. It should contain one 'port' child node +@@ -46,9 +46,9 @@ Example: + reg = <0x7e801000 0x800>, + <0x7e802004 0x4>; + interrupts = <2 7>; +- clocks = <&clocks BCM2835_CLOCK_CAM1>; +- clock-names = "lp"; +- ++ clocks = <&clocks BCM2835_CLOCK_CAM1>, ++ <&firmware_clocks 4>; ++ clock-names = "lp", "vpu"; + port { + csi1_ep: endpoint { + remote-endpoint = <&tc358743_0>; diff --git a/target/linux/bcm27xx/patches-5.10/950-0296-media-i2c-ov5647-Parse-and-register-properties.patch b/target/linux/bcm27xx/patches-5.10/950-0296-media-i2c-ov5647-Parse-and-register-properties.patch new file mode 100644 index 0000000000..10f5512b6a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0296-media-i2c-ov5647-Parse-and-register-properties.patch @@ -0,0 +1,49 @@ +From 0f0998ed9620f676ee78eb6f606b0b2fa118bf68 Mon Sep 17 00:00:00 2001 +From: Laurent Pinchart +Date: Sat, 4 Jul 2020 01:45:08 +0300 +Subject: [PATCH] media: i2c: ov5647: Parse and register properties + +Parse device properties and register controls for them using the V4L2 +fwnode properties helpers. + +Signed-off-by: Laurent Pinchart +--- + drivers/media/i2c/ov5647.c | 13 ++++++++++++- + 1 file changed, 12 insertions(+), 1 deletion(-) + +--- a/drivers/media/i2c/ov5647.c ++++ b/drivers/media/i2c/ov5647.c +@@ -1501,6 +1501,7 @@ static int ov5647_probe(struct i2c_clien + struct device_node *np = client->dev.of_node; + u32 xclk_freq; + int hblank, exposure_max, exposure_def; ++ struct v4l2_fwnode_device_properties props; + + sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL); + if (!sensor) +@@ -1534,7 +1535,7 @@ static int ov5647_probe(struct i2c_clien + mutex_init(&sensor->lock); + + /* Initialise controls. */ +- v4l2_ctrl_handler_init(&sensor->ctrls, 7); ++ v4l2_ctrl_handler_init(&sensor->ctrls, 9); + v4l2_ctrl_new_std(&sensor->ctrls, &ov5647_ctrl_ops, + V4L2_CID_AUTOGAIN, + 0, /* min */ +@@ -1598,6 +1599,16 @@ static int ov5647_probe(struct i2c_clien + __func__, ret); + goto error; + } ++ ++ ret = v4l2_fwnode_device_parse(&client->dev, &props); ++ if (ret) ++ goto error; ++ ++ ret = v4l2_ctrl_new_fwnode_properties(&sensor->ctrls, &ov5647_ctrl_ops, ++ &props); ++ if (ret) ++ goto error; ++ + sensor->sd.ctrl_handler = &sensor->ctrls; + + /* Write out the register set over I2C on stream-on. */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0297-leds-Add-the-actpwr-trigger.patch b/target/linux/bcm27xx/patches-5.10/950-0297-leds-Add-the-actpwr-trigger.patch new file mode 100644 index 0000000000..2b1257526f --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0297-leds-Add-the-actpwr-trigger.patch @@ -0,0 +1,235 @@ +From 136ae921cea7e7a189ee99d126253631f880ded0 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Mon, 13 Jul 2020 10:33:19 +0100 +Subject: [PATCH] leds: Add the actpwr trigger + +The actpwr trigger is a meta trigger that cycles between an inverted +mmc0 and default-on. It is written in a way that could fairly easily +be generalised to support alternative sets of source triggers. + +Signed-off-by: Phil Elwell +--- + drivers/leds/trigger/Kconfig | 11 ++ + drivers/leds/trigger/Makefile | 1 + + drivers/leds/trigger/ledtrig-actpwr.c | 190 ++++++++++++++++++++++++++ + 3 files changed, 202 insertions(+) + create mode 100644 drivers/leds/trigger/ledtrig-actpwr.c + +--- a/drivers/leds/trigger/Kconfig ++++ b/drivers/leds/trigger/Kconfig +@@ -151,4 +151,15 @@ config LEDS_TRIGGER_AUDIO + the audio mute and mic-mute changes. + If unsure, say N + ++config LEDS_TRIGGER_ACTPWR ++ tristate "ACT/PWR Input Trigger" ++ depends on LEDS_TRIGGERS ++ help ++ This trigger is intended for platforms that have one software- ++ controllable LED and no dedicated activity or power LEDs, hence the ++ need to make the one LED perform both functions. It cycles between ++ default-on and an inverted mmc0 every 500ms, guaranteeing that it is ++ on for at least half of the time. ++ If unsure, say N. ++ + endif # LEDS_TRIGGERS +--- a/drivers/leds/trigger/Makefile ++++ b/drivers/leds/trigger/Makefile +@@ -16,3 +16,4 @@ obj-$(CONFIG_LEDS_TRIGGER_PANIC) += ledt + obj-$(CONFIG_LEDS_TRIGGER_NETDEV) += ledtrig-netdev.o + obj-$(CONFIG_LEDS_TRIGGER_PATTERN) += ledtrig-pattern.o + obj-$(CONFIG_LEDS_TRIGGER_AUDIO) += ledtrig-audio.o ++obj-$(CONFIG_LEDS_TRIGGER_ACTPWR) += ledtrig-actpwr.o +--- /dev/null ++++ b/drivers/leds/trigger/ledtrig-actpwr.c +@@ -0,0 +1,190 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * Activity/power trigger ++ * ++ * Copyright (C) 2020 Raspberry Pi (Trading) Ltd. ++ * ++ * Based on Atsushi Nemoto's ledtrig-heartbeat.c, although there may be ++ * nothing left of the original now. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include "../leds.h" ++ ++enum { ++ TRIG_ACT, ++ TRIG_PWR, ++ ++ TRIG_COUNT ++}; ++ ++struct actpwr_trig_src { ++ const char *name; ++ int interval; ++ bool invert; ++}; ++ ++struct actpwr_vled { ++ struct led_classdev cdev; ++ struct actpwr_trig_data *parent; ++ enum led_brightness value; ++ unsigned int interval; ++ bool invert; ++}; ++ ++struct actpwr_trig_data { ++ struct led_trigger trig; ++ struct actpwr_vled virt_leds[TRIG_COUNT]; ++ struct actpwr_vled *active; ++ struct timer_list timer; ++ int next_active; ++}; ++ ++static int actpwr_trig_activate(struct led_classdev *led_cdev); ++static void actpwr_trig_deactivate(struct led_classdev *led_cdev); ++ ++static const struct actpwr_trig_src actpwr_trig_sources[TRIG_COUNT] = { ++ [TRIG_ACT] = { "mmc0", 500, true }, ++ [TRIG_PWR] = { "default-on", 500, false }, ++}; ++ ++static struct actpwr_trig_data actpwr_data = { ++ { ++ .name = "actpwr", ++ .activate = actpwr_trig_activate, ++ .deactivate = actpwr_trig_deactivate, ++ } ++}; ++ ++static void actpwr_brightness_set(struct led_classdev *led_cdev, ++ enum led_brightness value) ++{ ++ struct actpwr_vled *vled = container_of(led_cdev, struct actpwr_vled, ++ cdev); ++ struct actpwr_trig_data *trig = vled->parent; ++ ++ if (vled->invert) ++ value = !value; ++ vled->value = value; ++ ++ if (vled == trig->active) ++ led_trigger_event(&trig->trig, value); ++} ++ ++static int actpwr_brightness_set_blocking(struct led_classdev *led_cdev, ++ enum led_brightness value) ++{ ++ actpwr_brightness_set(led_cdev, value); ++ return 0; ++} ++ ++static enum led_brightness actpwr_brightness_get(struct led_classdev *led_cdev) ++{ ++ struct actpwr_vled *vled = container_of(led_cdev, struct actpwr_vled, ++ cdev); ++ ++ return vled->value; ++} ++ ++static void actpwr_trig_cycle(struct timer_list *t) ++{ ++ struct actpwr_trig_data *trig = &actpwr_data; ++ struct actpwr_vled *active; ++ ++ active = &trig->virt_leds[trig->next_active]; ++ trig->active = active; ++ trig->next_active = (trig->next_active + 1) % TRIG_COUNT; ++ ++ led_trigger_event(&trig->trig, active->value); ++ ++ mod_timer(&trig->timer, jiffies + msecs_to_jiffies(active->interval)); ++} ++ ++static int actpwr_trig_activate(struct led_classdev *led_cdev) ++{ ++ struct actpwr_trig_data *trig = &actpwr_data; ++ ++ /* Start the timer if this is the first LED */ ++ if (!trig->active) ++ actpwr_trig_cycle(&trig->timer); ++ else ++ led_set_brightness_nosleep(led_cdev, trig->active->value); ++ ++ return 0; ++} ++ ++static void actpwr_trig_deactivate(struct led_classdev *led_cdev) ++{ ++ struct actpwr_trig_data *trig = &actpwr_data; ++ ++ if (list_empty(&trig->trig.led_cdevs)) { ++ del_timer_sync(&trig->timer); ++ trig->active = NULL; ++ } ++} ++ ++static int __init actpwr_trig_init(void) ++{ ++ struct actpwr_trig_data *trig = &actpwr_data; ++ int ret = 0; ++ int i; ++ ++ timer_setup(&trig->timer, actpwr_trig_cycle, 0); ++ ++ /* Register one "LED" for each source trigger */ ++ for (i = 0; i < TRIG_COUNT; i++) ++ { ++ struct actpwr_vled *vled = &trig->virt_leds[i]; ++ struct led_classdev *cdev = &vled->cdev; ++ const struct actpwr_trig_src *src = &actpwr_trig_sources[i]; ++ ++ vled->parent = trig; ++ vled->interval = src->interval; ++ vled->invert = src->invert; ++ cdev->name = src->name; ++ cdev->brightness_set = actpwr_brightness_set; ++ cdev->brightness_set_blocking = actpwr_brightness_set_blocking; ++ cdev->brightness_get = actpwr_brightness_get; ++ cdev->default_trigger = src->name; ++ ret = led_classdev_register(NULL, cdev); ++ if (ret) ++ goto error_classdev; ++ } ++ ++ ret = led_trigger_register(&trig->trig); ++ if (ret) ++ goto error_classdev; ++ ++ return 0; ++ ++error_classdev: ++ while (i > 0) ++ { ++ i--; ++ led_classdev_unregister(&trig->virt_leds[i].cdev); ++ } ++ ++ return ret; ++} ++ ++static void __exit actpwr_trig_exit(void) ++{ ++ int i; ++ ++ led_trigger_unregister(&actpwr_data.trig); ++ for (i = 0; i < TRIG_COUNT; i++) ++ { ++ led_classdev_unregister(&actpwr_data.virt_leds[i].cdev); ++ } ++} ++ ++module_init(actpwr_trig_init); ++module_exit(actpwr_trig_exit); ++ ++MODULE_AUTHOR("Phil Elwell "); ++MODULE_DESCRIPTION("ACT/PWR LED trigger"); ++MODULE_LICENSE("GPL v2"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0298-staging-vchiq_arm-children-inherit-DMA-config.patch b/target/linux/bcm27xx/patches-5.10/950-0298-staging-vchiq_arm-children-inherit-DMA-config.patch new file mode 100644 index 0000000000..b9e548c7ff --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0298-staging-vchiq_arm-children-inherit-DMA-config.patch @@ -0,0 +1,36 @@ +From e2e8b2dfdfda27958a276c719fda8b162f229bc8 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 21 Jul 2020 17:34:09 +0100 +Subject: [PATCH] staging: vchiq_arm: children inherit DMA config + +Although it is no longer necessary for vchiq's children to have a +different DMA configuration to the parent, they do still need to +explicitly to have their DMA configuration set - to be that of the +parent. + +Signed-off-by: Phil Elwell +--- + .../vc04_services/interface/vchiq_arm/vchiq_arm.c | 10 ++++++++++ + 1 file changed, 10 insertions(+) + +--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c ++++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_arm.c +@@ -2720,8 +2720,18 @@ vchiq_register_child(struct platform_dev + + child->dev.of_node = np; + ++ /* ++ * We want the dma-ranges etc to be copied from the parent VCHIQ device ++ * to be passed on to the children without a node of their own. ++ */ ++ if (!np) ++ np = pdev->dev.of_node; ++ + of_dma_configure(&child->dev, np, true); + ++ if (np != pdev->dev.of_node) ++ of_node_put(np); ++ + return child; + } + diff --git a/target/linux/bcm27xx/patches-5.10/950-0299-bcm2835-dma-Advertise-the-full-DMA-range.patch b/target/linux/bcm27xx/patches-5.10/950-0299-bcm2835-dma-Advertise-the-full-DMA-range.patch new file mode 100644 index 0000000000..be31b6984a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0299-bcm2835-dma-Advertise-the-full-DMA-range.patch @@ -0,0 +1,77 @@ +From 0aa2706c9c452213c352400a41e4878c09995153 Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 22 Jul 2020 17:59:31 +0100 +Subject: [PATCH] bcm2835-dma: Advertise the full DMA range + +Unless the DMA mask is set wider than 32 bits, DMA mapping will use a +bounce buffer. + +Signed-off-by: Phil Elwell +--- + drivers/dma/bcm2835-dma.c | 18 +++++++++++++++--- + 1 file changed, 15 insertions(+), 3 deletions(-) + +--- a/drivers/dma/bcm2835-dma.c ++++ b/drivers/dma/bcm2835-dma.c +@@ -41,6 +41,7 @@ + #define BCM2711_DMA_MEMCPY_CHAN 14 + + struct bcm2835_dma_cfg_data { ++ u64 dma_mask; + u32 chan_40bit_mask; + }; + +@@ -300,10 +301,12 @@ DEFINE_SPINLOCK(memcpy_lock); + + static const struct bcm2835_dma_cfg_data bcm2835_dma_cfg = { + .chan_40bit_mask = 0, ++ .dma_mask = DMA_BIT_MASK(32), + }; + + static const struct bcm2835_dma_cfg_data bcm2711_dma_cfg = { + .chan_40bit_mask = BIT(11) | BIT(12) | BIT(13) | BIT(14), ++ .dma_mask = DMA_BIT_MASK(36), + }; + + static inline size_t bcm2835_dma_max_frame_length(struct bcm2835_chan *c) +@@ -1180,6 +1183,8 @@ static struct dma_chan *bcm2835_dma_xlat + + static int bcm2835_dma_probe(struct platform_device *pdev) + { ++ const struct bcm2835_dma_cfg_data *cfg_data; ++ const struct of_device_id *of_id; + struct bcm2835_dmadev *od; + struct resource *res; + void __iomem *base; +@@ -1189,13 +1194,20 @@ static int bcm2835_dma_probe(struct plat + int irq_flags; + uint32_t chans_available; + char chan_name[BCM2835_DMA_CHAN_NAME_SIZE]; +- const struct of_device_id *of_id; + int chan_count, chan_start, chan_end; + ++ of_id = of_match_node(bcm2835_dma_of_match, pdev->dev.of_node); ++ if (!of_id) { ++ dev_err(&pdev->dev, "Failed to match compatible string\n"); ++ return -EINVAL; ++ } ++ ++ cfg_data = of_id->data; ++ + if (!pdev->dev.dma_mask) + pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask; + +- rc = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32)); ++ rc = dma_set_mask_and_coherent(&pdev->dev, cfg_data->dma_mask); + if (rc) { + dev_err(&pdev->dev, "Unable to set DMA mask\n"); + return rc; +@@ -1260,7 +1272,7 @@ static int bcm2835_dma_probe(struct plat + return -EINVAL; + } + +- od->cfg_data = of_id->data; ++ od->cfg_data = cfg_data; + + /* Request DMA channel mask from device tree */ + if (of_property_read_u32(pdev->dev.of_node, diff --git a/target/linux/bcm27xx/patches-5.10/950-0300-ARM-proc-v7-Force-misalignment-of-early-stmia.patch b/target/linux/bcm27xx/patches-5.10/950-0300-ARM-proc-v7-Force-misalignment-of-early-stmia.patch new file mode 100644 index 0000000000..3910f77230 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0300-ARM-proc-v7-Force-misalignment-of-early-stmia.patch @@ -0,0 +1,60 @@ +From 9e5b2debe12d4e840a7d3ec0cf22b215396ed46e Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Wed, 29 Jul 2020 13:47:55 +0100 +Subject: [PATCH] ARM: proc-v7: Force misalignment of early stmia + +In an attempt to prevent the problem of CPUn not starting, explicitly +misalign the scratch space used to save registers acros the cache +invalidation. + +Notes: +At this stage in the boot process the core is running with its cache +disabled. Before enabling the cache its contents must be explicitly +invalidated, a process that requires quite a few registers that the +caller must preserve. Evidence suggests that something is writing a +block of zeroes over that space at a time when all other cores should +be idle, possibly some kind of write-combiner, and the misalignment is +designed to disrupt any write-coalescing. + +In truth, I don't understand why this patch works, and when the failure +is so random it is hard to be certain that this isn't just rolling the +dice again. One interesting test would be to change the "addeq r12, #4"s +to "addeq r12, #0"s determine see if the offset itself is significant or +just the additional code. + +See: https://github.com/Hexxeh/rpi-firmware/issues/232 + +Signed-off-by: Phil Elwell +--- + arch/arm/mm/proc-v7.S | 6 +++++- + 1 file changed, 5 insertions(+), 1 deletion(-) + +--- a/arch/arm/mm/proc-v7.S ++++ b/arch/arm/mm/proc-v7.S +@@ -287,6 +287,8 @@ __v7_ca17mp_setup: + mov r10, #0 + 1: adr r0, __v7_setup_stack_ptr + ldr r12, [r0] ++ tst r12, #0x1f ++ addeq r12, r12, #4 + add r12, r12, r0 @ the local stack + stmia r12, {r1-r6, lr} @ v7_invalidate_l1 touches r0-r6 + bl v7_invalidate_l1 +@@ -474,6 +476,8 @@ __v7_setup: + adr r0, __v7_setup_stack_ptr + ldr r12, [r0] + add r12, r12, r0 @ the local stack ++ tst r12, #0x1f ++ addeq r12, r12, #4 + stmia r12, {r1-r6, lr} @ v7_invalidate_l1 touches r0-r6 + bl v7_invalidate_l1 + ldmia r12, {r1-r6, lr} +@@ -557,7 +561,7 @@ ENDPROC(__v7_setup) + .bss + .align 2 + __v7_setup_stack: +- .space 4 * 7 @ 7 registers ++ .space 4 * 8 @ 7 registers + 1 spare + + __INITDATA + diff --git a/target/linux/bcm27xx/patches-5.10/950-0301-media-bcm2835-unicam-Select-MEDIA_CONTROLLER-and-VID.patch b/target/linux/bcm27xx/patches-5.10/950-0301-media-bcm2835-unicam-Select-MEDIA_CONTROLLER-and-VID.patch new file mode 100644 index 0000000000..b85588cc28 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0301-media-bcm2835-unicam-Select-MEDIA_CONTROLLER-and-VID.patch @@ -0,0 +1,27 @@ +From 37e99c4779131e96caf9083b68dad151ef8a9219 Mon Sep 17 00:00:00 2001 +From: Hristo Venev +Date: Wed, 19 Aug 2020 17:02:22 +0300 +Subject: [PATCH] media: bcm2835: unicam: Select MEDIA_CONTROLLER and + VIDEO_V4L2_SUBDEV_API + +That is what almost all other drivers appear to be doing. + +Signed-off-by: Hristo Venev +--- + drivers/media/platform/bcm2835/Kconfig | 4 +++- + 1 file changed, 3 insertions(+), 1 deletion(-) + +--- a/drivers/media/platform/bcm2835/Kconfig ++++ b/drivers/media/platform/bcm2835/Kconfig +@@ -2,8 +2,10 @@ + + config VIDEO_BCM2835_UNICAM + tristate "Broadcom BCM2835 Unicam video capture driver" +- depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && MEDIA_CONTROLLER ++ depends on VIDEO_V4L2 + depends on ARCH_BCM2835 || COMPILE_TEST ++ select VIDEO_V4L2_SUBDEV_API ++ select MEDIA_CONTROLLER + select VIDEOBUF2_DMA_CONTIG + select V4L2_FWNODE + help diff --git a/target/linux/bcm27xx/patches-5.10/950-0302-staging-media-rpivid-Select-MEDIA_CONTROLLER-and-MED.patch b/target/linux/bcm27xx/patches-5.10/950-0302-staging-media-rpivid-Select-MEDIA_CONTROLLER-and-MED.patch new file mode 100644 index 0000000000..9e28c0bba2 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0302-staging-media-rpivid-Select-MEDIA_CONTROLLER-and-MED.patch @@ -0,0 +1,32 @@ +From 09cc3528a822ee9d1f7be9e19af760b5e60f1c8f Mon Sep 17 00:00:00 2001 +From: Hristo Venev +Date: Wed, 19 Aug 2020 17:05:53 +0300 +Subject: [PATCH] staging: media: rpivid: Select MEDIA_CONTROLLER and + MEDIA_CONTROLLER_REQUEST_API + +MEDIA_CONTROLLER_REQUEST_API is a hidden option. If rpivid depends on it, +the user would need to first enable another driver that selects +MEDIA_CONTROLLER_REQUEST_API, and only then rpivid would become available. + +By selecting it instead of depending on it, it becomes possible to enable +rpivid without having to enable other potentially unnecessary drivers. + +Signed-off-by: Hristo Venev +--- + drivers/staging/media/rpivid/Kconfig | 4 ++-- + 1 file changed, 2 insertions(+), 2 deletions(-) + +--- a/drivers/staging/media/rpivid/Kconfig ++++ b/drivers/staging/media/rpivid/Kconfig +@@ -3,9 +3,9 @@ + config VIDEO_RPIVID + tristate "Rpi H265 driver" + depends on VIDEO_DEV && VIDEO_V4L2 +- depends on MEDIA_CONTROLLER + depends on OF +- depends on MEDIA_CONTROLLER_REQUEST_API ++ select MEDIA_CONTROLLER ++ select MEDIA_CONTROLLER_REQUEST_API + select VIDEOBUF2_DMA_CONTIG + select V4L2_MEM2MEM_DEV + help diff --git a/target/linux/bcm27xx/patches-5.10/950-0303-media-bcm2835-unicam-Drop-WARN-on-uing-direct-cache-.patch b/target/linux/bcm27xx/patches-5.10/950-0303-media-bcm2835-unicam-Drop-WARN-on-uing-direct-cache-.patch new file mode 100644 index 0000000000..7526aa2d4c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0303-media-bcm2835-unicam-Drop-WARN-on-uing-direct-cache-.patch @@ -0,0 +1,34 @@ +From b8f093d573b6de5ca22642c60abfe3f49fdfed6b Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 27 Aug 2020 16:30:26 +0100 +Subject: [PATCH] media: bcm2835-unicam: Drop WARN on uing direct cache + alias + +Pi 0&1 pass all ARM accesses through the VPU L2 cache, therefore +the dma-ranges property sets the cache alias bits to other +than the direct alias, hence this WARN was firing. + +It was overprotective coding, so assume that everything is OK +with the dma-ranges, and remove the WARN. + +Signed-off-by: Dave Stevenson +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 7 ------- + 1 file changed, 7 deletions(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -709,13 +709,6 @@ static void unicam_wr_dma_addr(struct un + { + dma_addr_t endaddr = dmaaddr + buffer_size; + +- /* +- * dmaaddr and endaddr should be a 32-bit address with the top two bits +- * set to 0x3 to signify uncached access through the Videocore memory +- * controller. +- */ +- WARN_ON((dmaaddr >> 30) != 0x3 || (endaddr >> 30) != 0x3); +- + if (pad_id == IMAGE_PAD) { + reg_write(dev, UNICAM_IBSA0, dmaaddr); + reg_write(dev, UNICAM_IBEA0, endaddr); diff --git a/target/linux/bcm27xx/patches-5.10/950-0304-media-i2c-tc358743-Only-allow-supported-pixel-fmts-i.patch b/target/linux/bcm27xx/patches-5.10/950-0304-media-i2c-tc358743-Only-allow-supported-pixel-fmts-i.patch new file mode 100644 index 0000000000..ca2c70cc3b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0304-media-i2c-tc358743-Only-allow-supported-pixel-fmts-i.patch @@ -0,0 +1,30 @@ +From d542ce00f99420cce4ccaa9cb79e3a216c5ae583 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Fri, 10 Jul 2020 12:40:50 +0100 +Subject: [PATCH] media: i2c: tc358743: Only allow supported pixel fmts + in set_fmt + +Fix commit "media: tc358743: Return an appropriate colorspace from +tc358743_set_fmt" to ensure that the format passed in to set_fmt +is checked to be valid, and reset to the current format if not. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/tc358743.c | 6 ++++-- + 1 file changed, 4 insertions(+), 2 deletions(-) + +--- a/drivers/media/i2c/tc358743.c ++++ b/drivers/media/i2c/tc358743.c +@@ -1731,8 +1731,10 @@ static int tc358743_set_fmt(struct v4l2_ + u32 code = format->format.code; /* is overwritten by get_fmt */ + int ret = tc358743_get_fmt(sd, cfg, format); + +- format->format.code = code; +- format->format.colorspace = tc358743_g_colorspace(code); ++ if (code == MEDIA_BUS_FMT_RGB888_1X24 || ++ code == MEDIA_BUS_FMT_UYVY8_1X16) ++ format->format.code = code; ++ format->format.colorspace = tc358743_g_colorspace(format->format.code); + + if (ret) + return ret; diff --git a/target/linux/bcm27xx/patches-5.10/950-0305-media-i2c-ov9281-Add-support-for-8-bit-readout.patch b/target/linux/bcm27xx/patches-5.10/950-0305-media-i2c-ov9281-Add-support-for-8-bit-readout.patch new file mode 100644 index 0000000000..145402e213 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0305-media-i2c-ov9281-Add-support-for-8-bit-readout.patch @@ -0,0 +1,188 @@ +From 071d66e19764cb2019e95cb44d08a1848e688f12 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 7 Jul 2020 18:29:10 +0100 +Subject: [PATCH] media: i2c: ov9281: Add support for 8 bit readout + +The sensor supports 8 bit mode as well as 10bit, so add the +relevant code to allow selection of this. + +Signed-off-by: Dave Stevenson +--- + drivers/media/i2c/ov9281.c | 66 ++++++++++++++++++++++++++++++-------- + 1 file changed, 52 insertions(+), 14 deletions(-) + +--- a/drivers/media/i2c/ov9281.c ++++ b/drivers/media/i2c/ov9281.c +@@ -29,11 +29,12 @@ + + #define OV9281_LINK_FREQ_400MHZ 400000000 + #define OV9281_LANES 2 +-#define OV9281_BITS_PER_SAMPLE 10 + + /* pixel rate = link frequency * 2 * lanes / BITS_PER_SAMPLE */ +-#define OV9281_PIXEL_RATE (OV9281_LINK_FREQ_400MHZ * 2 * \ +- OV9281_LANES / OV9281_BITS_PER_SAMPLE) ++#define OV9281_PIXEL_RATE_10BIT (OV9281_LINK_FREQ_400MHZ * 2 * \ ++ OV9281_LANES / 10) ++#define OV9281_PIXEL_RATE_8BIT (OV9281_LINK_FREQ_400MHZ * 2 * \ ++ OV9281_LANES / 8) + #define OV9281_XVCLK_FREQ 24000000 + + #define CHIP_ID 0x9281 +@@ -122,24 +123,25 @@ struct ov9281 { + struct v4l2_ctrl *digi_gain; + struct v4l2_ctrl *hblank; + struct v4l2_ctrl *vblank; ++ struct v4l2_ctrl *pixel_rate; + struct v4l2_ctrl *test_pattern; + struct mutex mutex; + bool streaming; + bool power_on; + const struct ov9281_mode *cur_mode; ++ u32 code; + }; + + #define to_ov9281(sd) container_of(sd, struct ov9281, subdev) + + /* + * Xclk 24Mhz +- * max_framerate 120fps ++ * max_framerate 120fps for 10 bit, 144fps for 8 bit. + * mipi_datarate per lane 800Mbps + */ + static const struct regval ov9281_1280x800_regs[] = { + {0x0103, 0x01}, + {0x0302, 0x32}, +- {0x030d, 0x50}, + {0x030e, 0x02}, + {0x3001, 0x00}, + {0x3004, 0x00}, +@@ -168,7 +170,6 @@ static const struct regval ov9281_1280x8 + {0x3620, 0x6f}, + {0x3632, 0x56}, + {0x3633, 0x78}, +- {0x3662, 0x05}, + {0x3666, 0x00}, + {0x366f, 0x5a}, + {0x3680, 0x84}, +@@ -235,6 +236,18 @@ static const struct regval ov9281_1280x8 + {REG_NULL, 0x00}, + }; + ++static const struct regval op_10bit[] = { ++ {0x030d, 0x50}, ++ {0x3662, 0x05}, ++ {REG_NULL, 0x00}, ++}; ++ ++static const struct regval op_8bit[] = { ++ {0x030d, 0x60}, ++ {0x3662, 0x07}, ++ {REG_NULL, 0x00}, ++}; ++ + static const struct ov9281_mode supported_modes[] = { + { + .width = 1280, +@@ -374,12 +387,13 @@ static int ov9281_set_fmt(struct v4l2_su + { + struct ov9281 *ov9281 = to_ov9281(sd); + const struct ov9281_mode *mode; +- s64 h_blank, vblank_def; ++ s64 h_blank, vblank_def, pixel_rate; + + mutex_lock(&ov9281->mutex); + + mode = ov9281_find_best_fit(fmt); +- fmt->format.code = MEDIA_BUS_FMT_Y10_1X10; ++ if (fmt->format.code != MEDIA_BUS_FMT_Y8_1X8) ++ fmt->format.code = MEDIA_BUS_FMT_Y10_1X10; + fmt->format.width = mode->width; + fmt->format.height = mode->height; + fmt->format.field = V4L2_FIELD_NONE; +@@ -396,6 +410,7 @@ static int ov9281_set_fmt(struct v4l2_su + *v4l2_subdev_get_try_format(sd, cfg, fmt->pad) = fmt->format; + } else { + ov9281->cur_mode = mode; ++ ov9281->code = fmt->format.code; + h_blank = mode->hts_def - mode->width; + __v4l2_ctrl_modify_range(ov9281->hblank, h_blank, + h_blank, 1, h_blank); +@@ -405,6 +420,11 @@ static int ov9281_set_fmt(struct v4l2_su + OV9281_VTS_MAX - mode->height, + 1, vblank_def); + __v4l2_ctrl_s_ctrl(ov9281->vblank, vblank_def); ++ ++ pixel_rate = (fmt->format.code == MEDIA_BUS_FMT_Y10_1X10) ? ++ OV9281_PIXEL_RATE_10BIT : OV9281_PIXEL_RATE_8BIT; ++ __v4l2_ctrl_modify_range(ov9281->pixel_rate, pixel_rate, ++ pixel_rate, 1, pixel_rate); + } + + mutex_unlock(&ov9281->mutex); +@@ -425,7 +445,7 @@ static int ov9281_get_fmt(struct v4l2_su + } else { + fmt->format.width = mode->width; + fmt->format.height = mode->height; +- fmt->format.code = MEDIA_BUS_FMT_Y10_1X10; ++ fmt->format.code = ov9281->code; + fmt->format.field = V4L2_FIELD_NONE; + fmt->format.colorspace = V4L2_COLORSPACE_SRGB; + fmt->format.ycbcr_enc = +@@ -446,9 +466,16 @@ static int ov9281_enum_mbus_code(struct + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_mbus_code_enum *code) + { +- if (code->index) ++ switch (code->index) { ++ default: + return -EINVAL; +- code->code = MEDIA_BUS_FMT_Y10_1X10; ++ case 0: ++ code->code = MEDIA_BUS_FMT_Y10_1X10; ++ break; ++ case 1: ++ code->code = MEDIA_BUS_FMT_Y8_1X8; ++ break; ++ } + + return 0; + } +@@ -460,7 +487,8 @@ static int ov9281_enum_frame_sizes(struc + if (fse->index >= ARRAY_SIZE(supported_modes)) + return -EINVAL; + +- if (fse->code != MEDIA_BUS_FMT_Y10_1X10) ++ if (fse->code != MEDIA_BUS_FMT_Y10_1X10 && ++ fse->code != MEDIA_BUS_FMT_Y8_1X8) + return -EINVAL; + + fse->min_width = supported_modes[fse->index].width; +@@ -543,6 +571,13 @@ static int __ov9281_start_stream(struct + if (ret) + return ret; + ++ if (ov9281->code == MEDIA_BUS_FMT_Y10_1X10) ++ ret = ov9281_write_array(ov9281->client, op_10bit); ++ else ++ ret = ov9281_write_array(ov9281->client, op_8bit); ++ if (ret) ++ return ret; ++ + /* In case these controls are set before streaming */ + mutex_unlock(&ov9281->mutex); + ret = v4l2_ctrl_handler_setup(&ov9281->ctrl_handler); +@@ -849,8 +884,11 @@ static int ov9281_initialize_controls(st + if (ctrl) + ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY; + +- v4l2_ctrl_new_std(handler, NULL, V4L2_CID_PIXEL_RATE, +- 0, OV9281_PIXEL_RATE, 1, OV9281_PIXEL_RATE); ++ ov9281->pixel_rate = v4l2_ctrl_new_std(handler, NULL, ++ V4L2_CID_PIXEL_RATE, ++ OV9281_PIXEL_RATE_10BIT, ++ OV9281_PIXEL_RATE_10BIT, 1, ++ OV9281_PIXEL_RATE_10BIT); + + h_blank = mode->hts_def - mode->width; + ov9281->hblank = v4l2_ctrl_new_std(handler, NULL, V4L2_CID_HBLANK, diff --git a/target/linux/bcm27xx/patches-5.10/950-0306-bcm2835-mmc-uninitialized_var-is-no-more.patch b/target/linux/bcm27xx/patches-5.10/950-0306-bcm2835-mmc-uninitialized_var-is-no-more.patch new file mode 100644 index 0000000000..a89e4ab112 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0306-bcm2835-mmc-uninitialized_var-is-no-more.patch @@ -0,0 +1,20 @@ +From 99c87c4c80fb0dd24f6849d0846c0c4a418903a9 Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Thu, 3 Sep 2020 14:02:21 +0100 +Subject: [PATCH] bcm2835-mmc: uninitialized_var is no more + +--- + drivers/mmc/host/bcm2835-mmc.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/mmc/host/bcm2835-mmc.c ++++ b/drivers/mmc/host/bcm2835-mmc.c +@@ -367,7 +367,7 @@ static void bcm2835_bcm2835_mmc_read_blo + unsigned long flags; + size_t blksize, len, chunk; + +- u32 uninitialized_var(scratch); ++ u32 scratch = 0; + u8 *buf; + + blksize = host->data->blksz; diff --git a/target/linux/bcm27xx/patches-5.10/950-0307-dwc_otg-whitelist_table-is-now-productlist_table.patch b/target/linux/bcm27xx/patches-5.10/950-0307-dwc_otg-whitelist_table-is-now-productlist_table.patch new file mode 100644 index 0000000000..6841a2df4a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0307-dwc_otg-whitelist_table-is-now-productlist_table.patch @@ -0,0 +1,20 @@ +From 1ecaa185ff343a783c147b17dd85482c507d2d9e Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Thu, 3 Sep 2020 14:02:41 +0100 +Subject: [PATCH] dwc_otg: whitelist_table is now productlist_table + +--- + drivers/usb/core/otg_productlist.h | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/usb/core/otg_productlist.h ++++ b/drivers/usb/core/otg_productlist.h +@@ -139,7 +139,7 @@ static int is_targeted(struct usb_device + /* NOTE: can't use usb_match_id() since interface caches + * aren't set up yet. this is cut/paste from that code. + */ +- for (id = whitelist_table; id->match_flags; id++) { ++ for (id = productlist_table; id->match_flags; id++) { + #ifdef DEBUG + dev_dbg(&dev->dev, + "ID: V:%04x P:%04x DC:%04x SC:%04x PR:%04x \n", diff --git a/target/linux/bcm27xx/patches-5.10/950-0308-vchiq_2835_arm-Implement-a-DMA-pool-for-small-bulk-t.patch b/target/linux/bcm27xx/patches-5.10/950-0308-vchiq_2835_arm-Implement-a-DMA-pool-for-small-bulk-t.patch new file mode 100644 index 0000000000..991c962ac6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0308-vchiq_2835_arm-Implement-a-DMA-pool-for-small-bulk-t.patch @@ -0,0 +1,122 @@ +From afbc6c9f890bd3d877451138b2ffd5bd19bfdf61 Mon Sep 17 00:00:00 2001 +From: detule +Date: Tue, 2 Oct 2018 04:10:08 -0400 +Subject: [PATCH] vchiq_2835_arm: Implement a DMA pool for small bulk + transfers (#2699) + +During a bulk transfer we request a DMA allocation to hold the +scatter-gather list. Most of the time, this allocation is small +(<< PAGE_SIZE), however it can be requested at a high enough frequency +to cause fragmentation and/or stress the CMA allocator (think time +spent in compaction here, or during allocations elsewhere). + +Implement a pool to serve up small DMA allocations, falling back +to a coherent allocation if the request is greater than +VCHIQ_DMA_POOL_SIZE. + +Signed-off-by: Oliver Gjoneski +--- + .../interface/vchiq_arm/vchiq_2835_arm.c | 36 ++++++++++++++++--- + 1 file changed, 32 insertions(+), 4 deletions(-) + +--- a/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_2835_arm.c ++++ b/drivers/staging/vc04_services/interface/vchiq_arm/vchiq_2835_arm.c +@@ -7,6 +7,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -29,6 +30,8 @@ + #define BELL0 0x00 + #define BELL2 0x08 + ++#define VCHIQ_DMA_POOL_SIZE PAGE_SIZE ++ + struct vchiq_2835_state { + int inited; + struct vchiq_arm_state arm_state; +@@ -38,6 +41,7 @@ struct vchiq_pagelist_info { + struct pagelist *pagelist; + size_t pagelist_buffer_size; + dma_addr_t dma_addr; ++ bool is_from_pool; + enum dma_data_direction dma_dir; + unsigned int num_pages; + unsigned int pages_need_release; +@@ -58,6 +62,7 @@ static void __iomem *g_regs; + * of 32. + */ + static unsigned int g_cache_line_size = 32; ++static struct dma_pool *g_dma_pool; + static unsigned int g_use_36bit_addrs = 0; + static unsigned int g_fragments_size; + static char *g_fragments_base; +@@ -182,6 +187,13 @@ int vchiq_platform_init(struct platform_ + + g_dev = dev; + g_dma_dev = dma_dev ?: dev; ++ g_dma_pool = dmam_pool_create("vchiq_scatter_pool", dev, ++ VCHIQ_DMA_POOL_SIZE, g_cache_line_size, ++ 0); ++ if (!g_dma_pool) { ++ dev_err(dev, "failed to create dma pool"); ++ return -ENOMEM; ++ } + + vchiq_log_info(vchiq_arm_log_level, + "vchiq_init - done (slots %pK, phys %pad)", +@@ -314,8 +326,14 @@ cleanup_pagelistinfo(struct vchiq_pageli + if (pagelistinfo->pages_need_release) + unpin_user_pages(pagelistinfo->pages, pagelistinfo->num_pages); + +- dma_free_coherent(g_dev, pagelistinfo->pagelist_buffer_size, +- pagelistinfo->pagelist, pagelistinfo->dma_addr); ++ if (pagelistinfo->is_from_pool) { ++ dma_pool_free(g_dma_pool, pagelistinfo->pagelist, ++ pagelistinfo->dma_addr); ++ } else { ++ dma_free_coherent(g_dev, pagelistinfo->pagelist_buffer_size, ++ pagelistinfo->pagelist, ++ pagelistinfo->dma_addr); ++ } + } + + /* There is a potential problem with partial cache lines (pages?) +@@ -336,6 +354,7 @@ create_pagelist(char *buf, char __user * + u32 *addrs; + unsigned int num_pages, offset, i, k; + int actual_pages; ++ bool is_from_pool; + size_t pagelist_size; + struct scatterlist *scatterlist, *sg; + int dma_buffers; +@@ -365,8 +384,16 @@ create_pagelist(char *buf, char __user * + /* Allocate enough storage to hold the page pointers and the page + * list + */ +- pagelist = dma_alloc_coherent(g_dev, pagelist_size, &dma_addr, +- GFP_KERNEL); ++ if (pagelist_size > VCHIQ_DMA_POOL_SIZE) { ++ pagelist = dma_alloc_coherent(g_dev, ++ pagelist_size, ++ &dma_addr, ++ GFP_KERNEL); ++ is_from_pool = false; ++ } else { ++ pagelist = dma_pool_alloc(g_dma_pool, GFP_KERNEL, &dma_addr); ++ is_from_pool = true; ++ } + + vchiq_log_trace(vchiq_arm_log_level, "%s - %pK", __func__, pagelist); + +@@ -387,6 +414,7 @@ create_pagelist(char *buf, char __user * + pagelistinfo->pagelist = pagelist; + pagelistinfo->pagelist_buffer_size = pagelist_size; + pagelistinfo->dma_addr = dma_addr; ++ pagelistinfo->is_from_pool = is_from_pool; + pagelistinfo->dma_dir = (type == PAGELIST_WRITE) ? + DMA_TO_DEVICE : DMA_FROM_DEVICE; + pagelistinfo->num_pages = num_pages; diff --git a/target/linux/bcm27xx/patches-5.10/950-0309-include-firmware-Add-enum-for-RPI_FIRMWARE_FRAMEBUFF.patch b/target/linux/bcm27xx/patches-5.10/950-0309-include-firmware-Add-enum-for-RPI_FIRMWARE_FRAMEBUFF.patch new file mode 100644 index 0000000000..fda153f06c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0309-include-firmware-Add-enum-for-RPI_FIRMWARE_FRAMEBUFF.patch @@ -0,0 +1,23 @@ +From 80025c80d57bdd265e47d1bfe62e68f54ca672d5 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Thu, 3 Sep 2020 17:09:07 +0100 +Subject: [PATCH] include/firmware: Add enum for + RPI_FIRMWARE_FRAMEBUFFER_GET_DISPLAY_ID + +Used by audio and FKMS. + +Signed-off-by: Dave Stevenson +--- + include/soc/bcm2835/raspberrypi-firmware.h | 1 + + 1 file changed, 1 insertion(+) + +--- a/include/soc/bcm2835/raspberrypi-firmware.h ++++ b/include/soc/bcm2835/raspberrypi-firmware.h +@@ -114,6 +114,7 @@ enum rpi_firmware_property_tag { + RPI_FIRMWARE_FRAMEBUFFER_GET_TOUCHBUF = 0x0004000f, + RPI_FIRMWARE_FRAMEBUFFER_GET_GPIOVIRTBUF = 0x00040010, + RPI_FIRMWARE_FRAMEBUFFER_RELEASE = 0x00048001, ++ RPI_FIRMWARE_FRAMEBUFFER_GET_DISPLAY_ID = 0x00040016, + RPI_FIRMWARE_FRAMEBUFFER_SET_DISPLAY_NUM = 0x00048013, + RPI_FIRMWARE_FRAMEBUFFER_GET_NUM_DISPLAYS = 0x00040013, + RPI_FIRMWARE_FRAMEBUFFER_GET_DISPLAY_SETTINGS = 0x00040014, diff --git a/target/linux/bcm27xx/patches-5.10/950-0310-vc4_hdmi-Remove-cec_available-flag-as-always-support.patch b/target/linux/bcm27xx/patches-5.10/950-0310-vc4_hdmi-Remove-cec_available-flag-as-always-support.patch new file mode 100644 index 0000000000..a11a43f80c --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0310-vc4_hdmi-Remove-cec_available-flag-as-always-support.patch @@ -0,0 +1,44 @@ +From 8dda85398458dc330758ef5e1408d66995ffa068 Mon Sep 17 00:00:00 2001 +From: Dom Cobley +Date: Thu, 7 May 2020 18:16:09 +0100 +Subject: [PATCH] vc4_hdmi: Remove cec_available flag as always + supported + +Signed-off-by: Dom Cobley +--- + drivers/gpu/drm/vc4/vc4_hdmi.c | 4 ---- + drivers/gpu/drm/vc4/vc4_hdmi.h | 3 --- + 2 files changed, 7 deletions(-) + +--- a/drivers/gpu/drm/vc4/vc4_hdmi.c ++++ b/drivers/gpu/drm/vc4/vc4_hdmi.c +@@ -1488,9 +1488,6 @@ static int vc4_hdmi_cec_init(struct vc4_ + u32 value; + int ret; + +- if (!vc4_hdmi->variant->cec_available) +- return 0; +- + vc4_hdmi->cec_adap = cec_allocate_adapter(&vc4_hdmi_cec_adap_ops, + vc4_hdmi, "vc4", + CEC_CAP_DEFAULTS | +@@ -1910,7 +1907,6 @@ static const struct vc4_hdmi_variant bcm + .debugfs_name = "hdmi_regs", + .card_name = "vc4-hdmi", + .max_pixel_clock = 162000000, +- .cec_available = true, + .registers = vc4_hdmi_fields, + .num_registers = ARRAY_SIZE(vc4_hdmi_fields), + +--- a/drivers/gpu/drm/vc4/vc4_hdmi.h ++++ b/drivers/gpu/drm/vc4/vc4_hdmi.h +@@ -43,9 +43,6 @@ struct vc4_hdmi_variant { + /* Filename to expose the registers in debugfs */ + const char *debugfs_name; + +- /* Set to true when the CEC support is available */ +- bool cec_available; +- + /* Maximum pixel clock supported by the controller (in Hz) */ + unsigned long long max_pixel_clock; + diff --git a/target/linux/bcm27xx/patches-5.10/950-0311-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch b/target/linux/bcm27xx/patches-5.10/950-0311-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch new file mode 100644 index 0000000000..b99102f6d2 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0311-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch @@ -0,0 +1,54 @@ +From d57ee5afedf0b1b9a9afb29357c484acda5a40af Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 19 May 2020 14:54:28 +0100 +Subject: [PATCH] drm/vc4: Adopt the dma configuration from the HVS or + V3D component + +vc4_drv isn't necessarily under the /soc node in DT as it is a +virtual device, but it is the one that does the allocations. +The DMA addresses are consumed by primarily the HVS or V3D, and +those require VideoCore cache alias address mapping, and so will be +under /soc. + +During probe find the a suitable device node for HVS or V3D, +and adopt the DMA configuration of that node. + +Signed-off-by: Dave Stevenson +--- + drivers/gpu/drm/vc4/vc4_drv.c | 18 ++++++++++++++++++ + 1 file changed, 18 insertions(+) + +--- a/drivers/gpu/drm/vc4/vc4_drv.c ++++ b/drivers/gpu/drm/vc4/vc4_drv.c +@@ -246,6 +246,14 @@ static void vc4_match_add_drivers(struct + } + } + ++const struct of_device_id vc4_dma_range_matches[] = { ++ { .compatible = "brcm,bcm2835-hvs" }, ++ { .compatible = "brcm,bcm2835-v3d" }, ++ { .compatible = "brcm,cygnus-v3d" }, ++ { .compatible = "brcm,vc4-v3d" }, ++ {} ++}; ++ + static int vc4_drm_bind(struct device *dev) + { + struct platform_device *pdev = to_platform_device(dev); +@@ -263,6 +271,16 @@ static int vc4_drm_bind(struct device *d + vc4_drm_driver.driver_features &= ~DRIVER_RENDER; + of_node_put(node); + ++ node = of_find_matching_node_and_match(NULL, vc4_dma_range_matches, ++ NULL); ++ if (node) { ++ ret = of_dma_configure(dev, node, true); ++ of_node_put(node); ++ ++ if (ret) ++ return ret; ++ } ++ + vc4 = devm_drm_dev_alloc(dev, &vc4_drm_driver, struct vc4_dev, base); + if (IS_ERR(vc4)) + return PTR_ERR(vc4); diff --git a/target/linux/bcm27xx/patches-5.10/950-0312-vc4_hdmi-Set-HD_CTL_WHOLSMP-and-HD_CTL_CHALIGN_SET.patch b/target/linux/bcm27xx/patches-5.10/950-0312-vc4_hdmi-Set-HD_CTL_WHOLSMP-and-HD_CTL_CHALIGN_SET.patch new file mode 100644 index 0000000000..3ab091ba33 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0312-vc4_hdmi-Set-HD_CTL_WHOLSMP-and-HD_CTL_CHALIGN_SET.patch @@ -0,0 +1,42 @@ +From 1a0b802bb6bca3b42034245d35b56309749a362c Mon Sep 17 00:00:00 2001 +From: Dom Cobley +Date: Tue, 23 Jun 2020 18:37:01 +0100 +Subject: [PATCH] vc4_hdmi: Set HD_CTL_WHOLSMP and HD_CTL_CHALIGN_SET + +Symptom is random switching of speakers when using multichannel. + +Repeatedly running speakertest -c8 occasionally starts with +channels jumbled. This is fixed with HD_CTL_WHOLSMP. + +The other bit looks beneficial and apears harmless in testing so +I'd suggest adding it too. + +Documentation says: HD_CTL_WHILSMP_SET +Wait for whole sample. When this bit is set MAI transmit will start +only when there is at least one whole sample available in the fifo. + +Documentation says: HD_CTL_CHALIGN_SET +Channel Align When Overflow. This bit is used to realign the audio +channels in case of an overflow. +If this bit is set, after the detection of an overflow, equal +amount of dummy words to the missing words will be written to fifo, +filling up the broken sample and maintaining alignment. + +Signed-off-by: Dom Cobley +--- + drivers/gpu/drm/vc4/vc4_hdmi.c | 4 +++- + 1 file changed, 3 insertions(+), 1 deletion(-) + +--- a/drivers/gpu/drm/vc4/vc4_hdmi.c ++++ b/drivers/gpu/drm/vc4/vc4_hdmi.c +@@ -1074,7 +1074,9 @@ static int vc4_hdmi_audio_trigger(struct + HDMI_WRITE(HDMI_MAI_CTL, + VC4_SET_FIELD(vc4_hdmi->audio.channels, + VC4_HD_MAI_CTL_CHNUM) | +- VC4_HD_MAI_CTL_ENABLE); ++ VC4_HD_MAI_CTL_WHOLSMP | ++ VC4_HD_MAI_CTL_CHALIGN | ++ VC4_HD_MAI_CTL_ENABLE); + break; + case SNDRV_PCM_TRIGGER_STOP: + HDMI_WRITE(HDMI_MAI_CTL, diff --git a/target/linux/bcm27xx/patches-5.10/950-0313-vc4_hdmi-Set-HDMI_MAI_FMT.patch b/target/linux/bcm27xx/patches-5.10/950-0313-vc4_hdmi-Set-HDMI_MAI_FMT.patch new file mode 100644 index 0000000000..a1f423cefb --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0313-vc4_hdmi-Set-HDMI_MAI_FMT.patch @@ -0,0 +1,124 @@ +From 80ba4d12d096a8f7855835ee54dc17d1e3a0d31a Mon Sep 17 00:00:00 2001 +From: popcornmix +Date: Tue, 10 Mar 2020 22:21:15 +0000 +Subject: [PATCH] vc4_hdmi: Set HDMI_MAI_FMT + +The hardware uses this for generating the right audio +data island packets when using formats other than PCM + +Signed-off-by: Dom Cobley +--- + drivers/gpu/drm/vc4/vc4_hdmi.c | 48 ++++++++++++++++++++++++++++++++++ + drivers/gpu/drm/vc4/vc4_regs.h | 30 +++++++++++++++++++++ + 2 files changed, 78 insertions(+) + +--- a/drivers/gpu/drm/vc4/vc4_hdmi.c ++++ b/drivers/gpu/drm/vc4/vc4_hdmi.c +@@ -988,6 +988,44 @@ static void vc4_hdmi_audio_shutdown(stru + vc4_hdmi->audio.substream = NULL; + } + ++static int sample_rate_to_mai_fmt(int samplerate) ++{ ++ switch (samplerate) { ++ case 8000: ++ return VC4_HDMI_MAI_SAMPLE_RATE_8000; ++ case 11025: ++ return VC4_HDMI_MAI_SAMPLE_RATE_11025; ++ case 12000: ++ return VC4_HDMI_MAI_SAMPLE_RATE_12000; ++ case 16000: ++ return VC4_HDMI_MAI_SAMPLE_RATE_16000; ++ case 22050: ++ return VC4_HDMI_MAI_SAMPLE_RATE_22050; ++ case 24000: ++ return VC4_HDMI_MAI_SAMPLE_RATE_24000; ++ case 32000: ++ return VC4_HDMI_MAI_SAMPLE_RATE_32000; ++ case 44100: ++ return VC4_HDMI_MAI_SAMPLE_RATE_44100; ++ case 48000: ++ return VC4_HDMI_MAI_SAMPLE_RATE_48000; ++ case 64000: ++ return VC4_HDMI_MAI_SAMPLE_RATE_64000; ++ case 88200: ++ return VC4_HDMI_MAI_SAMPLE_RATE_88200; ++ case 96000: ++ return VC4_HDMI_MAI_SAMPLE_RATE_96000; ++ case 128000: ++ return VC4_HDMI_MAI_SAMPLE_RATE_128000; ++ case 176400: ++ return VC4_HDMI_MAI_SAMPLE_RATE_176400; ++ case 192000: ++ return VC4_HDMI_MAI_SAMPLE_RATE_192000; ++ default: ++ return VC4_HDMI_MAI_SAMPLE_RATE_NOT_INDICATED; ++ } ++} ++ + /* HDMI audio codec callbacks */ + static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream, + struct snd_pcm_hw_params *params, +@@ -998,6 +1036,8 @@ static int vc4_hdmi_audio_hw_params(stru + struct device *dev = &vc4_hdmi->pdev->dev; + u32 audio_packet_config, channel_mask; + u32 channel_map; ++ u32 mai_audio_format; ++ u32 mai_sample_rate; + + if (substream != vc4_hdmi->audio.substream) + return -EINVAL; +@@ -1018,6 +1058,14 @@ static int vc4_hdmi_audio_hw_params(stru + + vc4_hdmi_audio_set_mai_clock(vc4_hdmi); + ++ mai_sample_rate = sample_rate_to_mai_fmt(vc4_hdmi->audio.samplerate); ++ mai_audio_format = VC4_HDMI_MAI_FORMAT_PCM; ++ HDMI_WRITE(HDMI_MAI_FMT, ++ VC4_SET_FIELD(mai_sample_rate, ++ VC4_HDMI_MAI_FORMAT_SAMPLE_RATE) | ++ VC4_SET_FIELD(mai_audio_format, ++ VC4_HDMI_MAI_FORMAT_AUDIO_FORMAT)); ++ + /* The B frame identifier should match the value used by alsa-lib (8) */ + audio_packet_config = + VC4_HDMI_AUDIO_PACKET_ZERO_DATA_ON_SAMPLE_FLAT | +--- a/drivers/gpu/drm/vc4/vc4_regs.h ++++ b/drivers/gpu/drm/vc4/vc4_regs.h +@@ -516,6 +516,36 @@ + # define VC4_HDMI_AUDIO_PACKET_CEA_MASK_MASK VC4_MASK(7, 0) + # define VC4_HDMI_AUDIO_PACKET_CEA_MASK_SHIFT 0 + ++# define VC4_HDMI_MAI_FORMAT_AUDIO_FORMAT_MASK VC4_MASK(23, 16) ++# define VC4_HDMI_MAI_FORMAT_AUDIO_FORMAT_SHIFT 16 ++ ++enum { ++ VC4_HDMI_MAI_FORMAT_PCM = 2, ++ VC4_HDMI_MAI_FORMAT_HBR = 200, ++}; ++ ++# define VC4_HDMI_MAI_FORMAT_SAMPLE_RATE_MASK VC4_MASK(15, 8) ++# define VC4_HDMI_MAI_FORMAT_SAMPLE_RATE_SHIFT 8 ++ ++enum { ++ VC4_HDMI_MAI_SAMPLE_RATE_NOT_INDICATED = 0, ++ VC4_HDMI_MAI_SAMPLE_RATE_8000 = 1, ++ VC4_HDMI_MAI_SAMPLE_RATE_11025 = 2, ++ VC4_HDMI_MAI_SAMPLE_RATE_12000 = 3, ++ VC4_HDMI_MAI_SAMPLE_RATE_16000 = 4, ++ VC4_HDMI_MAI_SAMPLE_RATE_22050 = 5, ++ VC4_HDMI_MAI_SAMPLE_RATE_24000 = 6, ++ VC4_HDMI_MAI_SAMPLE_RATE_32000 = 7, ++ VC4_HDMI_MAI_SAMPLE_RATE_44100 = 8, ++ VC4_HDMI_MAI_SAMPLE_RATE_48000 = 9, ++ VC4_HDMI_MAI_SAMPLE_RATE_64000 = 10, ++ VC4_HDMI_MAI_SAMPLE_RATE_88200 = 11, ++ VC4_HDMI_MAI_SAMPLE_RATE_96000 = 12, ++ VC4_HDMI_MAI_SAMPLE_RATE_128000 = 13, ++ VC4_HDMI_MAI_SAMPLE_RATE_176400 = 14, ++ VC4_HDMI_MAI_SAMPLE_RATE_192000 = 15, ++}; ++ + # define VC4_HDMI_RAM_PACKET_ENABLE BIT(16) + + /* When set, the CTS_PERIOD counts based on MAI bus sync pulse instead diff --git a/target/linux/bcm27xx/patches-5.10/950-0314-drm-vc4-add-iec958-controls-to-vc4_hdmi.patch b/target/linux/bcm27xx/patches-5.10/950-0314-drm-vc4-add-iec958-controls-to-vc4_hdmi.patch new file mode 100644 index 0000000000..9369658500 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0314-drm-vc4-add-iec958-controls-to-vc4_hdmi.patch @@ -0,0 +1,119 @@ +From 29e5bf9305e98a57a895d6806fafa6e67f257fd8 Mon Sep 17 00:00:00 2001 +From: Matthias Reichl +Date: Tue, 17 Mar 2020 12:12:22 +0100 +Subject: [PATCH] drm/vc4: add iec958 controls to vc4_hdmi + +Although vc4 get an IEC958 formatted stream passed in from userspace +the driver needs the info from the channel status bits to properly +set up the hardware, eg for HBR passthrough. + +Add iec958 controls so the channel status bits can be passed in +from userspace. + +Signed-off-by: Matthias Reichl +--- + drivers/gpu/drm/vc4/vc4_hdmi.c | 60 ++++++++++++++++++++++++++++++++++ + drivers/gpu/drm/vc4/vc4_hdmi.h | 2 ++ + 2 files changed, 62 insertions(+) + +--- a/drivers/gpu/drm/vc4/vc4_hdmi.c ++++ b/drivers/gpu/drm/vc4/vc4_hdmi.c +@@ -44,6 +44,7 @@ + #include + #include + #include ++#include + #include + #include + #include +@@ -1179,6 +1180,47 @@ static int vc4_hdmi_audio_eld_ctl_get(st + return 0; + } + ++static int vc4_spdif_info(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_info *uinfo) ++{ ++ uinfo->type = SNDRV_CTL_ELEM_TYPE_IEC958; ++ uinfo->count = 1; ++ return 0; ++} ++ ++static int vc4_spdif_playback_get(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); ++ struct vc4_hdmi *vc4_hdmi = snd_component_to_hdmi(component); ++ ++ memcpy(ucontrol->value.iec958.status, vc4_hdmi->audio.iec_status, ++ sizeof(vc4_hdmi->audio.iec_status)); ++ ++ return 0; ++} ++ ++static int vc4_spdif_playback_put(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ struct snd_soc_component *component = snd_kcontrol_chip(kcontrol); ++ struct vc4_hdmi *vc4_hdmi = snd_component_to_hdmi(component); ++ ++ memcpy(vc4_hdmi->audio.iec_status, ucontrol->value.iec958.status, ++ sizeof(vc4_hdmi->audio.iec_status)); ++ ++ return 0; ++} ++ ++static int vc4_spdif_mask_get(struct snd_kcontrol *kcontrol, ++ struct snd_ctl_elem_value *ucontrol) ++{ ++ memset(ucontrol->value.iec958.status, 0xff, ++ sizeof_field(struct vc4_hdmi_audio, iec_status)); ++ ++ return 0; ++} ++ + static const struct snd_kcontrol_new vc4_hdmi_audio_controls[] = { + { + .access = SNDRV_CTL_ELEM_ACCESS_READ | +@@ -1188,6 +1230,19 @@ static const struct snd_kcontrol_new vc4 + .info = vc4_hdmi_audio_eld_ctl_info, + .get = vc4_hdmi_audio_eld_ctl_get, + }, ++ { ++ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, ++ .name = SNDRV_CTL_NAME_IEC958("", PLAYBACK, DEFAULT), ++ .info = vc4_spdif_info, ++ .get = vc4_spdif_playback_get, ++ .put = vc4_spdif_playback_put, ++ }, ++ { ++ .iface = SNDRV_CTL_ELEM_IFACE_MIXER, ++ .name = SNDRV_CTL_NAME_IEC958("", PLAYBACK, MASK), ++ .info = vc4_spdif_info, ++ .get = vc4_spdif_mask_get, ++ }, + }; + + static const struct snd_soc_dapm_widget vc4_hdmi_audio_widgets[] = { +@@ -1308,6 +1363,11 @@ static int vc4_hdmi_audio_init(struct vc + vc4_hdmi->audio.dma_data.addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + vc4_hdmi->audio.dma_data.maxburst = 2; + ++ vc4_hdmi->audio.iec_status[0] = IEC958_AES0_CON_NOT_COPYRIGHT; ++ vc4_hdmi->audio.iec_status[1] = ++ IEC958_AES1_CON_ORIGINAL | IEC958_AES1_CON_PCM_CODER; ++ vc4_hdmi->audio.iec_status[3] = IEC958_AES3_CON_FS_48000; ++ + ret = devm_snd_dmaengine_pcm_register(dev, &pcm_conf, 0); + if (ret) { + dev_err(dev, "Could not register PCM component: %d\n", ret); +--- a/drivers/gpu/drm/vc4/vc4_hdmi.h ++++ b/drivers/gpu/drm/vc4/vc4_hdmi.h +@@ -107,6 +107,8 @@ struct vc4_hdmi_audio { + struct snd_pcm_substream *substream; + + bool streaming; ++ ++ unsigned char iec_status[4]; + }; + + /* General HDMI hardware state. */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0315-drm-vc4-move-setup-from-hw_params-to-prepare.patch b/target/linux/bcm27xx/patches-5.10/950-0315-drm-vc4-move-setup-from-hw_params-to-prepare.patch new file mode 100644 index 0000000000..cfe27b866a --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0315-drm-vc4-move-setup-from-hw_params-to-prepare.patch @@ -0,0 +1,58 @@ +From 7b6cfdfc74c7e9c00060a0c4146a6358b261f7db Mon Sep 17 00:00:00 2001 +From: Matthias Reichl +Date: Thu, 19 Mar 2020 20:00:35 +0100 +Subject: [PATCH] drm/vc4: move setup from hw_params to prepare + +Configuring HDMI audio registers in prepare allows us to take +IEC958 bits into account which are set by the alsa hook after +the hw_params call. + +Signed-off-by: Matthias Reichl +--- + drivers/gpu/drm/vc4/vc4_hdmi.c | 20 +++++++++++--------- + 1 file changed, 11 insertions(+), 9 deletions(-) + +--- a/drivers/gpu/drm/vc4/vc4_hdmi.c ++++ b/drivers/gpu/drm/vc4/vc4_hdmi.c +@@ -1028,9 +1028,8 @@ static int sample_rate_to_mai_fmt(int sa + } + + /* HDMI audio codec callbacks */ +-static int vc4_hdmi_audio_hw_params(struct snd_pcm_substream *substream, +- struct snd_pcm_hw_params *params, +- struct snd_soc_dai *dai) ++static int vc4_hdmi_audio_prepare(struct snd_pcm_substream *substream, ++ struct snd_soc_dai *dai) + { + struct vc4_hdmi *vc4_hdmi = dai_to_hdmi(dai); + struct drm_encoder *encoder = &vc4_hdmi->encoder.base.base; +@@ -1043,12 +1042,15 @@ static int vc4_hdmi_audio_hw_params(stru + if (substream != vc4_hdmi->audio.substream) + return -EINVAL; + +- dev_dbg(dev, "%s: %u Hz, %d bit, %d channels\n", __func__, +- params_rate(params), params_width(params), +- params_channels(params)); ++ dev_dbg(dev, "%s: %u Hz, %d bit, %d channels AES0=%02x\n", ++ __func__, ++ substream->runtime->rate, ++ snd_pcm_format_width(substream->runtime->format), ++ substream->runtime->channels, ++ vc4_hdmi->audio.iec_status[0]); + +- vc4_hdmi->audio.channels = params_channels(params); +- vc4_hdmi->audio.samplerate = params_rate(params); ++ vc4_hdmi->audio.channels = substream->runtime->channels; ++ vc4_hdmi->audio.samplerate = substream->runtime->rate; + + HDMI_WRITE(HDMI_MAI_CTL, + VC4_HD_MAI_CTL_RESET | +@@ -1270,7 +1272,7 @@ static const struct snd_soc_component_dr + static const struct snd_soc_dai_ops vc4_hdmi_audio_dai_ops = { + .startup = vc4_hdmi_audio_startup, + .shutdown = vc4_hdmi_audio_shutdown, +- .hw_params = vc4_hdmi_audio_hw_params, ++ .prepare = vc4_hdmi_audio_prepare, + .set_fmt = vc4_hdmi_audio_set_fmt, + .trigger = vc4_hdmi_audio_trigger, + }; diff --git a/target/linux/bcm27xx/patches-5.10/950-0316-drm-vc4-enable-HBR-MAI-format-on-HBR-streams.patch b/target/linux/bcm27xx/patches-5.10/950-0316-drm-vc4-enable-HBR-MAI-format-on-HBR-streams.patch new file mode 100644 index 0000000000..f48a12bd6e --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0316-drm-vc4-enable-HBR-MAI-format-on-HBR-streams.patch @@ -0,0 +1,25 @@ +From 465b5e6889b1af1c9c061751a0ee234a27644030 Mon Sep 17 00:00:00 2001 +From: Dom Cobley +Date: Fri, 10 Jul 2020 11:51:16 +0100 +Subject: [PATCH] drm/vc4: enable HBR MAI format on HBR streams + +Signed-off-by: Matthias Reichl +--- + drivers/gpu/drm/vc4/vc4_hdmi.c | 6 +++++- + 1 file changed, 5 insertions(+), 1 deletion(-) + +--- a/drivers/gpu/drm/vc4/vc4_hdmi.c ++++ b/drivers/gpu/drm/vc4/vc4_hdmi.c +@@ -1062,7 +1062,11 @@ static int vc4_hdmi_audio_prepare(struct + vc4_hdmi_audio_set_mai_clock(vc4_hdmi); + + mai_sample_rate = sample_rate_to_mai_fmt(vc4_hdmi->audio.samplerate); +- mai_audio_format = VC4_HDMI_MAI_FORMAT_PCM; ++ if (vc4_hdmi->audio.iec_status[0] & IEC958_AES0_NONAUDIO && ++ vc4_hdmi->audio.channels == 8) ++ mai_audio_format = VC4_HDMI_MAI_FORMAT_HBR; ++ else ++ mai_audio_format = VC4_HDMI_MAI_FORMAT_PCM; + HDMI_WRITE(HDMI_MAI_FMT, + VC4_SET_FIELD(mai_sample_rate, + VC4_HDMI_MAI_FORMAT_SAMPLE_RATE) | diff --git a/target/linux/bcm27xx/patches-5.10/950-0317-vc4_hdmi-Remove-firmware-logic-for-MAI-threshold-set.patch b/target/linux/bcm27xx/patches-5.10/950-0317-vc4_hdmi-Remove-firmware-logic-for-MAI-threshold-set.patch new file mode 100644 index 0000000000..96b5456d4b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0317-vc4_hdmi-Remove-firmware-logic-for-MAI-threshold-set.patch @@ -0,0 +1,47 @@ +From 3c398513990aa0edc5b9ebfbdd2395623562c6e4 Mon Sep 17 00:00:00 2001 +From: Dom Cobley +Date: Thu, 25 Jun 2020 18:48:40 +0100 +Subject: [PATCH] vc4_hdmi: Remove firmware logic for MAI threshold + setting + +This was a workaround for bugs in hardware on earlier Pi models +and wasn't totally successful. + +It makes audio quality worse on a Pi4 at the higher sample rates + +Signed-off-by: Dom Cobley +--- + drivers/gpu/drm/vc4/vc4_hdmi.c | 22 ++++++---------------- + 1 file changed, 6 insertions(+), 16 deletions(-) + +--- a/drivers/gpu/drm/vc4/vc4_hdmi.c ++++ b/drivers/gpu/drm/vc4/vc4_hdmi.c +@@ -1083,22 +1083,12 @@ static int vc4_hdmi_audio_prepare(struct + audio_packet_config |= VC4_SET_FIELD(channel_mask, + VC4_HDMI_AUDIO_PACKET_CEA_MASK); + +- /* Set the MAI threshold. This logic mimics the firmware's. */ +- if (vc4_hdmi->audio.samplerate > 96000) { +- HDMI_WRITE(HDMI_MAI_THR, +- VC4_SET_FIELD(0x12, VC4_HD_MAI_THR_DREQHIGH) | +- VC4_SET_FIELD(0x12, VC4_HD_MAI_THR_DREQLOW)); +- } else if (vc4_hdmi->audio.samplerate > 48000) { +- HDMI_WRITE(HDMI_MAI_THR, +- VC4_SET_FIELD(0x14, VC4_HD_MAI_THR_DREQHIGH) | +- VC4_SET_FIELD(0x12, VC4_HD_MAI_THR_DREQLOW)); +- } else { +- HDMI_WRITE(HDMI_MAI_THR, +- VC4_SET_FIELD(0x10, VC4_HD_MAI_THR_PANICHIGH) | +- VC4_SET_FIELD(0x10, VC4_HD_MAI_THR_PANICLOW) | +- VC4_SET_FIELD(0x10, VC4_HD_MAI_THR_DREQHIGH) | +- VC4_SET_FIELD(0x10, VC4_HD_MAI_THR_DREQLOW)); +- } ++ /* Set the MAI threshold */ ++ HDMI_WRITE(HDMI_MAI_THR, ++ VC4_SET_FIELD(0x10, VC4_HD_MAI_THR_PANICHIGH) | ++ VC4_SET_FIELD(0x10, VC4_HD_MAI_THR_PANICLOW) | ++ VC4_SET_FIELD(0x10, VC4_HD_MAI_THR_DREQHIGH) | ++ VC4_SET_FIELD(0x10, VC4_HD_MAI_THR_DREQLOW)); + + HDMI_WRITE(HDMI_MAI_CONFIG, + VC4_HDMI_MAI_CONFIG_BIT_REVERSE | diff --git a/target/linux/bcm27xx/patches-5.10/950-0318-vc_hdmi-Set-VC4_HDMI_MAI_CONFIG_FORMAT_REVERSE.patch b/target/linux/bcm27xx/patches-5.10/950-0318-vc_hdmi-Set-VC4_HDMI_MAI_CONFIG_FORMAT_REVERSE.patch new file mode 100644 index 0000000000..c5e1baa02b --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0318-vc_hdmi-Set-VC4_HDMI_MAI_CONFIG_FORMAT_REVERSE.patch @@ -0,0 +1,24 @@ +From f4a590c59a65381a0b9aa045e5fc493b3dbb5945 Mon Sep 17 00:00:00 2001 +From: Dom Cobley +Date: Tue, 30 Jun 2020 11:23:49 +0100 +Subject: [PATCH] vc_hdmi: Set VC4_HDMI_MAI_CONFIG_FORMAT_REVERSE + +Without this bit set, HDMI_MAI_FORMAT doesn't pick up +the format and samplerate from DVP_CFG_MAI0_FMT and you +can't get HDMI_HDMI_13_AUDIO_STATUS_1 to indicate HBR mode + +Signed-off-by: Dom Cobley +--- + drivers/gpu/drm/vc4/vc4_hdmi.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/gpu/drm/vc4/vc4_hdmi.c ++++ b/drivers/gpu/drm/vc4/vc4_hdmi.c +@@ -1092,6 +1092,7 @@ static int vc4_hdmi_audio_prepare(struct + + HDMI_WRITE(HDMI_MAI_CONFIG, + VC4_HDMI_MAI_CONFIG_BIT_REVERSE | ++ VC4_HDMI_MAI_CONFIG_FORMAT_REVERSE | + VC4_SET_FIELD(channel_mask, VC4_HDMI_MAI_CHANNEL_MASK)); + + channel_map = vc4_hdmi->variant->channel_map(vc4_hdmi, channel_mask); diff --git a/target/linux/bcm27xx/patches-5.10/950-0319-drm-vc4-Add-support-for-DRM_FORMAT_P030-to-vc4-plane.patch b/target/linux/bcm27xx/patches-5.10/950-0319-drm-vc4-Add-support-for-DRM_FORMAT_P030-to-vc4-plane.patch new file mode 100644 index 0000000000..c3db8c7319 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0319-drm-vc4-Add-support-for-DRM_FORMAT_P030-to-vc4-plane.patch @@ -0,0 +1,163 @@ +From 286cf26ca3f6628a82c8c37e7059585c8389b82a Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Fri, 24 Jan 2020 14:25:41 +0000 +Subject: [PATCH] drm/vc4: Add support for DRM_FORMAT_P030 to vc4 + planes + +This currently doesn't handle non-zero source rectangles correctly, +but add support for DRM_FORMAT_P030 with DRM_FORMAT_MOD_BROADCOM_SAND128 +modifier to planes when running on HVS5. + +WIP still for source cropping SAND/P030 formats + +Signed-off-by: Dave Stevenson +--- + drivers/gpu/drm/vc4/vc4_plane.c | 79 ++++++++++++++++++++++++--------- + 1 file changed, 57 insertions(+), 22 deletions(-) + +--- a/drivers/gpu/drm/vc4/vc4_plane.c ++++ b/drivers/gpu/drm/vc4/vc4_plane.c +@@ -33,6 +33,7 @@ static const struct hvs_format { + u32 hvs; /* HVS_FORMAT_* */ + u32 pixel_order; + u32 pixel_order_hvs5; ++ bool hvs5_only; + } hvs_formats[] = { + { + .drm = DRM_FORMAT_XRGB8888, +@@ -128,6 +129,12 @@ static const struct hvs_format { + .hvs = HVS_PIXEL_FORMAT_YCBCR_YUV422_2PLANE, + .pixel_order = HVS_PIXEL_ORDER_XYCRCB, + }, ++ { ++ .drm = DRM_FORMAT_P030, ++ .hvs = HVS_PIXEL_FORMAT_YCBCR_10BIT, ++ .pixel_order = HVS_PIXEL_ORDER_XYCBCR, ++ .hvs5_only = true, ++ }, + }; + + static const struct hvs_format *vc4_get_hvs_format(u32 drm_format) +@@ -769,27 +776,33 @@ static int vc4_plane_mode_set(struct drm + uint32_t param = fourcc_mod_broadcom_param(fb->modifier); + u32 tile_w, tile, x_off, pix_per_tile; + +- hvs_format = HVS_PIXEL_FORMAT_H264; +- +- switch (base_format_mod) { +- case DRM_FORMAT_MOD_BROADCOM_SAND64: +- tiling = SCALER_CTL0_TILING_64B; +- tile_w = 64; +- break; +- case DRM_FORMAT_MOD_BROADCOM_SAND128: ++ if (fb->format->format == DRM_FORMAT_P030) { ++ hvs_format = HVS_PIXEL_FORMAT_YCBCR_10BIT; + tiling = SCALER_CTL0_TILING_128B; +- tile_w = 128; +- break; +- case DRM_FORMAT_MOD_BROADCOM_SAND256: +- tiling = SCALER_CTL0_TILING_256B_OR_T; +- tile_w = 256; +- break; +- default: +- break; +- } ++ tile_w = 96; ++ } else { ++ hvs_format = HVS_PIXEL_FORMAT_H264; + ++ switch (base_format_mod) { ++ case DRM_FORMAT_MOD_BROADCOM_SAND64: ++ tiling = SCALER_CTL0_TILING_64B; ++ tile_w = 64; ++ break; ++ case DRM_FORMAT_MOD_BROADCOM_SAND128: ++ tiling = SCALER_CTL0_TILING_128B; ++ tile_w = 128; ++ break; ++ case DRM_FORMAT_MOD_BROADCOM_SAND256: ++ tiling = SCALER_CTL0_TILING_256B_OR_T; ++ tile_w = 256; ++ break; ++ default: ++ break; ++ } ++ } + if (param > SCALER_TILE_HEIGHT_MASK) { +- DRM_DEBUG_KMS("SAND height too large (%d)\n", param); ++ DRM_DEBUG_KMS("SAND height too large (%d)\n", ++ param); + return -EINVAL; + } + +@@ -799,6 +812,13 @@ static int vc4_plane_mode_set(struct drm + + /* Adjust the base pointer to the first pixel to be scanned + * out. ++ * ++ * For P030, y_ptr [31:4] is the 128bit word for the start pixel ++ * y_ptr [3:0] is the pixel (0-11) contained within that 128bit ++ * word that should be taken as the first pixel. ++ * Ditto uv_ptr [31:4] vs [3:0], however [3:0] contains the ++ * element within the 128bit word, eg for pixel 3 the value ++ * should be 6. + */ + for (i = 0; i < num_planes; i++) { + vc4_state->offsets[i] += param * tile_w * tile; +@@ -960,7 +980,8 @@ static int vc4_plane_mode_set(struct drm + + /* Pitch word 1/2 */ + for (i = 1; i < num_planes; i++) { +- if (hvs_format != HVS_PIXEL_FORMAT_H264) { ++ if (hvs_format != HVS_PIXEL_FORMAT_H264 && ++ hvs_format != HVS_PIXEL_FORMAT_YCBCR_10BIT) { + vc4_dlist_write(vc4_state, + VC4_SET_FIELD(fb->pitches[i], + SCALER_SRC_PITCH)); +@@ -1320,6 +1341,13 @@ static bool vc4_format_mod_supported(str + default: + return false; + } ++ case DRM_FORMAT_P030: ++ switch (fourcc_mod_broadcom_mod(modifier)) { ++ case DRM_FORMAT_MOD_BROADCOM_SAND128: ++ return true; ++ default: ++ return false; ++ } + case DRM_FORMAT_RGBX1010102: + case DRM_FORMAT_BGRX1010102: + case DRM_FORMAT_RGBA1010102: +@@ -1352,8 +1380,11 @@ struct drm_plane *vc4_plane_init(struct + struct drm_plane *plane = NULL; + struct vc4_plane *vc4_plane; + u32 formats[ARRAY_SIZE(hvs_formats)]; ++ int num_formats = 0; + int ret = 0; + unsigned i; ++ bool hvs5 = of_device_is_compatible(dev->dev->of_node, ++ "brcm,bcm2711-vc5"); + static const uint64_t modifiers[] = { + DRM_FORMAT_MOD_BROADCOM_VC4_T_TILED, + DRM_FORMAT_MOD_BROADCOM_SAND128, +@@ -1368,13 +1399,17 @@ struct drm_plane *vc4_plane_init(struct + if (!vc4_plane) + return ERR_PTR(-ENOMEM); + +- for (i = 0; i < ARRAY_SIZE(hvs_formats); i++) +- formats[i] = hvs_formats[i].drm; ++ for (i = 0; i < ARRAY_SIZE(hvs_formats); i++) { ++ if (!hvs_formats[i].hvs5_only || hvs5) { ++ formats[num_formats] = hvs_formats[i].drm; ++ num_formats++; ++ } ++ } + + plane = &vc4_plane->base; + ret = drm_universal_plane_init(dev, plane, 0, + &vc4_plane_funcs, +- formats, ARRAY_SIZE(formats), ++ formats, num_formats, + modifiers, type, NULL); + if (ret) + return ERR_PTR(ret); diff --git a/target/linux/bcm27xx/patches-5.10/950-0320-drm-vc4-Add-support-for-YUV-color-encodings-and-rang.patch b/target/linux/bcm27xx/patches-5.10/950-0320-drm-vc4-Add-support-for-YUV-color-encodings-and-rang.patch new file mode 100644 index 0000000000..23f0533472 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0320-drm-vc4-Add-support-for-YUV-color-encodings-and-rang.patch @@ -0,0 +1,139 @@ +From 9582109f14a5e357c6287b5ab658293e8359fa47 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 17 Sep 2019 18:28:17 +0100 +Subject: [PATCH] drm/vc4: Add support for YUV color encodings and + ranges + +The BT601/BT709 color encoding and limited vs full +range properties were not being exposed, defaulting +always to BT601 limited range. + +Expose the parameters and set the registers appropriately. + +Signed-off-by: Dave Stevenson +--- + drivers/gpu/drm/vc4/vc4_plane.c | 72 +++++++++++++++++++++++++++++++-- + drivers/gpu/drm/vc4/vc4_regs.h | 3 ++ + 2 files changed, 72 insertions(+), 3 deletions(-) + +--- a/drivers/gpu/drm/vc4/vc4_plane.c ++++ b/drivers/gpu/drm/vc4/vc4_plane.c +@@ -628,6 +628,53 @@ static int vc4_plane_allocate_lbm(struct + return 0; + } + ++/* The colorspace conversion matrices are held in 3 entries in the dlist. ++ * Create an array of them, with entries for each full and limited mode, and ++ * each supported colorspace. ++ */ ++#define VC4_LIMITED_RANGE 0 ++#define VC4_FULL_RANGE 1 ++ ++static const u32 colorspace_coeffs[2][DRM_COLOR_ENCODING_MAX][3] = { ++ { ++ /* Limited range */ ++ { ++ /* BT601 */ ++ SCALER_CSC0_ITR_R_601_5, ++ SCALER_CSC1_ITR_R_601_5, ++ SCALER_CSC2_ITR_R_601_5, ++ }, { ++ /* BT709 */ ++ SCALER_CSC0_ITR_R_709_3, ++ SCALER_CSC1_ITR_R_709_3, ++ SCALER_CSC2_ITR_R_709_3, ++ }, { ++ /* BT2020. Not supported yet - copy 601 */ ++ SCALER_CSC0_ITR_R_601_5, ++ SCALER_CSC1_ITR_R_601_5, ++ SCALER_CSC2_ITR_R_601_5, ++ } ++ }, { ++ /* Full range */ ++ { ++ /* JFIF */ ++ SCALER_CSC0_JPEG_JFIF, ++ SCALER_CSC1_JPEG_JFIF, ++ SCALER_CSC2_JPEG_JFIF, ++ }, { ++ /* BT709 */ ++ SCALER_CSC0_ITR_R_709_3_FR, ++ SCALER_CSC1_ITR_R_709_3_FR, ++ SCALER_CSC2_ITR_R_709_3_FR, ++ }, { ++ /* BT2020. Not supported yet - copy JFIF */ ++ SCALER_CSC0_JPEG_JFIF, ++ SCALER_CSC1_JPEG_JFIF, ++ SCALER_CSC2_JPEG_JFIF, ++ } ++ } ++}; ++ + /* Writes out a full display list for an active plane to the plane's + * private dlist state. + */ +@@ -992,9 +1039,20 @@ static int vc4_plane_mode_set(struct drm + + /* Colorspace conversion words */ + if (vc4_state->is_yuv) { +- vc4_dlist_write(vc4_state, SCALER_CSC0_ITR_R_601_5); +- vc4_dlist_write(vc4_state, SCALER_CSC1_ITR_R_601_5); +- vc4_dlist_write(vc4_state, SCALER_CSC2_ITR_R_601_5); ++ enum drm_color_encoding color_encoding = state->color_encoding; ++ enum drm_color_range color_range = state->color_range; ++ const u32 *ccm; ++ ++ if (color_encoding >= DRM_COLOR_ENCODING_MAX) ++ color_encoding = DRM_COLOR_YCBCR_BT601; ++ if (color_range >= DRM_COLOR_RANGE_MAX) ++ color_range = DRM_COLOR_YCBCR_LIMITED_RANGE; ++ ++ ccm = colorspace_coeffs[color_range][color_encoding]; ++ ++ vc4_dlist_write(vc4_state, ccm[0]); ++ vc4_dlist_write(vc4_state, ccm[1]); ++ vc4_dlist_write(vc4_state, ccm[2]); + } + + vc4_state->lbm_offset = 0; +@@ -1423,6 +1481,14 @@ struct drm_plane *vc4_plane_init(struct + DRM_MODE_REFLECT_X | + DRM_MODE_REFLECT_Y); + ++ drm_plane_create_color_properties(plane, ++ BIT(DRM_COLOR_YCBCR_BT601) | ++ BIT(DRM_COLOR_YCBCR_BT709), ++ BIT(DRM_COLOR_YCBCR_LIMITED_RANGE) | ++ BIT(DRM_COLOR_YCBCR_FULL_RANGE), ++ DRM_COLOR_YCBCR_BT709, ++ DRM_COLOR_YCBCR_LIMITED_RANGE); ++ + return plane; + } + +--- a/drivers/gpu/drm/vc4/vc4_regs.h ++++ b/drivers/gpu/drm/vc4/vc4_regs.h +@@ -976,6 +976,7 @@ enum hvs_pixel_format { + #define SCALER_CSC0_ITR_R_601_5 0x00f00000 + #define SCALER_CSC0_ITR_R_709_3 0x00f00000 + #define SCALER_CSC0_JPEG_JFIF 0x00000000 ++#define SCALER_CSC0_ITR_R_709_3_FR 0x00000000 + + /* S2.8 contribution of Cb to Green */ + #define SCALER_CSC1_COEF_CB_GRN_MASK VC4_MASK(31, 22) +@@ -992,6 +993,7 @@ enum hvs_pixel_format { + #define SCALER_CSC1_ITR_R_601_5 0xe73304a8 + #define SCALER_CSC1_ITR_R_709_3 0xf2b784a8 + #define SCALER_CSC1_JPEG_JFIF 0xea34a400 ++#define SCALER_CSC1_ITR_R_709_3_FR 0xe23d0400 + + /* S2.8 contribution of Cb to Red */ + #define SCALER_CSC2_COEF_CB_RED_MASK VC4_MASK(29, 20) +@@ -1005,6 +1007,7 @@ enum hvs_pixel_format { + #define SCALER_CSC2_ITR_R_601_5 0x00066204 + #define SCALER_CSC2_ITR_R_709_3 0x00072a1c + #define SCALER_CSC2_JPEG_JFIF 0x000599c5 ++#define SCALER_CSC2_ITR_R_709_3_FR 0x00064ddb + + #define SCALER_TPZ0_VERT_RECALC BIT(31) + #define SCALER_TPZ0_SCALE_MASK VC4_MASK(28, 8) diff --git a/target/linux/bcm27xx/patches-5.10/950-0321-drm-vc4-Add-firmware-kms-mode.patch b/target/linux/bcm27xx/patches-5.10/950-0321-drm-vc4-Add-firmware-kms-mode.patch new file mode 100644 index 0000000000..751c75fc32 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0321-drm-vc4-Add-firmware-kms-mode.patch @@ -0,0 +1,2364 @@ +From 0f304a905699ed05a418ac1cd98bcec6f2220a89 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Mon, 7 Sep 2020 17:32:27 +0100 +Subject: [PATCH] drm/vc4: Add firmware-kms mode + +This is a squash of all firmware-kms related patches from previous +branches, up to and including +"drm/vc4: Set the possible crtcs mask correctly for planes with FKMS" +plus a couple of minor fixups for the 5.9 branch. +Please refer to earlier branches for full history. + +This patch includes work by Eric Anholt, James Hughes, Phil Elwell, +Dave Stevenson, Dom Cobley, and Jonathon Bell. + +Signed-off-by: Dave Stevenson + +drm/vc4: Fixup firmware-kms after "drm/atomic: Pass the full state to CRTC atomic enable/disable" + +Prototype for those calls changed, so amend fkms (which isn't +upstream) to match. + +Signed-off-by: Dave Stevenson +--- + drivers/gpu/drm/vc4/Makefile | 1 + + drivers/gpu/drm/vc4/vc4_drv.c | 15 +- + drivers/gpu/drm/vc4/vc4_drv.h | 8 + + drivers/gpu/drm/vc4/vc4_firmware_kms.c | 1958 ++++++++++++++++++++ + drivers/gpu/drm/vc4/vc4_kms.c | 27 +- + drivers/gpu/drm/vc4/vc_image_types.h | 175 ++ + include/soc/bcm2835/raspberrypi-firmware.h | 6 + + 7 files changed, 2177 insertions(+), 13 deletions(-) + create mode 100644 drivers/gpu/drm/vc4/vc4_firmware_kms.c + create mode 100644 drivers/gpu/drm/vc4/vc_image_types.h + +--- a/drivers/gpu/drm/vc4/Makefile ++++ b/drivers/gpu/drm/vc4/Makefile +@@ -9,6 +9,7 @@ vc4-y := \ + vc4_dpi.o \ + vc4_dsi.o \ + vc4_fence.o \ ++ vc4_firmware_kms.o \ + vc4_kms.o \ + vc4_gem.o \ + vc4_hdmi.o \ +--- a/drivers/gpu/drm/vc4/vc4_drv.c ++++ b/drivers/gpu/drm/vc4/vc4_drv.c +@@ -307,9 +307,11 @@ static int vc4_drm_bind(struct device *d + if (ret) + return ret; + +- ret = vc4_plane_create_additional_planes(drm); +- if (ret) +- goto unbind_all; ++ if (!vc4->firmware_kms) { ++ ret = vc4_plane_create_additional_planes(drm); ++ if (ret) ++ goto unbind_all; ++ } + + drm_fb_helper_remove_conflicting_framebuffers(NULL, "vc4drmfb", false); + +@@ -317,8 +319,10 @@ static int vc4_drm_bind(struct device *d + if (ret < 0) + goto unbind_all; + +- drm_for_each_crtc(crtc, drm) +- vc4_crtc_disable_at_boot(crtc); ++ if (!vc4->firmware_kms) { ++ drm_for_each_crtc(crtc, drm) ++ vc4_crtc_disable_at_boot(crtc); ++ } + + ret = drm_dev_register(drm, 0); + if (ret < 0) +@@ -356,6 +360,7 @@ static struct platform_driver *const com + &vc4_hvs_driver, + &vc4_txp_driver, + &vc4_crtc_driver, ++ &vc4_firmware_kms_driver, + &vc4_v3d_driver, + }; + +--- a/drivers/gpu/drm/vc4/vc4_drv.h ++++ b/drivers/gpu/drm/vc4/vc4_drv.h +@@ -74,12 +74,17 @@ struct vc4_perfmon { + struct vc4_dev { + struct drm_device base; + ++ bool firmware_kms; ++ struct rpi_firmware *firmware; ++ ++ struct vc4_hdmi *hdmi; + struct vc4_hvs *hvs; + struct vc4_v3d *v3d; + struct vc4_dpi *dpi; + struct vc4_dsi *dsi1; + struct vc4_vec *vec; + struct vc4_txp *txp; ++ struct vc4_fkms *fkms; + + struct vc4_hang_state *hang_state; + +@@ -877,6 +882,9 @@ extern struct platform_driver vc4_dsi_dr + /* vc4_fence.c */ + extern const struct dma_fence_ops vc4_fence_ops; + ++/* vc4_firmware_kms.c */ ++extern struct platform_driver vc4_firmware_kms_driver; ++ + /* vc4_gem.c */ + int vc4_gem_init(struct drm_device *dev); + int vc4_submit_cl_ioctl(struct drm_device *dev, void *data, +--- /dev/null ++++ b/drivers/gpu/drm/vc4/vc4_firmware_kms.c +@@ -0,0 +1,1958 @@ ++// SPDX-License-Identifier: GPL-2.0-only ++/* ++ * Copyright (C) 2016 Broadcom ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++ ++/** ++ * DOC: VC4 firmware KMS module. ++ * ++ * As a hack to get us from the current closed source driver world ++ * toward a totally open stack, implement KMS on top of the Raspberry ++ * Pi's firmware display stack. ++ */ ++ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#include ++#include ++#include ++#include ++ ++#include ++ ++#include "vc4_drv.h" ++#include "vc4_regs.h" ++#include "vc_image_types.h" ++ ++int fkms_max_refresh_rate = 85; ++module_param(fkms_max_refresh_rate, int, 0644); ++MODULE_PARM_DESC(fkms_max_refresh_rate, "Max supported refresh rate"); ++ ++struct get_display_cfg { ++ u32 max_pixel_clock[2]; //Max pixel clock for each display ++}; ++ ++struct vc4_fkms { ++ struct get_display_cfg cfg; ++ bool bcm2711; ++}; ++ ++#define PLANES_PER_CRTC 8 ++ ++struct set_plane { ++ u8 display; ++ u8 plane_id; ++ u8 vc_image_type; ++ s8 layer; ++ ++ u16 width; ++ u16 height; ++ ++ u16 pitch; ++ u16 vpitch; ++ ++ u32 src_x; /* 16p16 */ ++ u32 src_y; /* 16p16 */ ++ ++ u32 src_w; /* 16p16 */ ++ u32 src_h; /* 16p16 */ ++ ++ s16 dst_x; ++ s16 dst_y; ++ ++ u16 dst_w; ++ u16 dst_h; ++ ++ u8 alpha; ++ u8 num_planes; ++ u8 is_vu; ++ u8 color_encoding; ++ ++ u32 planes[4]; /* DMA address of each plane */ ++ ++ u32 transform; ++}; ++ ++/* Values for the transform field */ ++#define TRANSFORM_NO_ROTATE 0 ++#define TRANSFORM_ROTATE_180 BIT(1) ++#define TRANSFORM_FLIP_HRIZ BIT(16) ++#define TRANSFORM_FLIP_VERT BIT(17) ++ ++struct mailbox_set_plane { ++ struct rpi_firmware_property_tag_header tag; ++ struct set_plane plane; ++}; ++ ++struct mailbox_blank_display { ++ struct rpi_firmware_property_tag_header tag1; ++ u32 display; ++ struct rpi_firmware_property_tag_header tag2; ++ u32 blank; ++}; ++ ++struct mailbox_display_pwr { ++ struct rpi_firmware_property_tag_header tag1; ++ u32 display; ++ u32 state; ++}; ++ ++struct mailbox_get_edid { ++ struct rpi_firmware_property_tag_header tag1; ++ u32 block; ++ u32 display_number; ++ u8 edid[128]; ++}; ++ ++struct set_timings { ++ u8 display; ++ u8 padding; ++ u16 video_id_code; ++ ++ u32 clock; /* in kHz */ ++ ++ u16 hdisplay; ++ u16 hsync_start; ++ ++ u16 hsync_end; ++ u16 htotal; ++ ++ u16 hskew; ++ u16 vdisplay; ++ ++ u16 vsync_start; ++ u16 vsync_end; ++ ++ u16 vtotal; ++ u16 vscan; ++ ++ u16 vrefresh; ++ u16 padding2; ++ ++ u32 flags; ++#define TIMINGS_FLAGS_H_SYNC_POS BIT(0) ++#define TIMINGS_FLAGS_H_SYNC_NEG 0 ++#define TIMINGS_FLAGS_V_SYNC_POS BIT(1) ++#define TIMINGS_FLAGS_V_SYNC_NEG 0 ++#define TIMINGS_FLAGS_INTERLACE BIT(2) ++ ++#define TIMINGS_FLAGS_ASPECT_MASK GENMASK(7, 4) ++#define TIMINGS_FLAGS_ASPECT_NONE (0 << 4) ++#define TIMINGS_FLAGS_ASPECT_4_3 (1 << 4) ++#define TIMINGS_FLAGS_ASPECT_16_9 (2 << 4) ++#define TIMINGS_FLAGS_ASPECT_64_27 (3 << 4) ++#define TIMINGS_FLAGS_ASPECT_256_135 (4 << 4) ++ ++/* Limited range RGB flag. Not set corresponds to full range. */ ++#define TIMINGS_FLAGS_RGB_LIMITED BIT(8) ++/* DVI monitor, therefore disable infoframes. Not set corresponds to HDMI. */ ++#define TIMINGS_FLAGS_DVI BIT(9) ++/* Double clock */ ++#define TIMINGS_FLAGS_DBL_CLK BIT(10) ++}; ++ ++struct mailbox_set_mode { ++ struct rpi_firmware_property_tag_header tag1; ++ struct set_timings timings; ++}; ++ ++static const struct vc_image_format { ++ u32 drm; /* DRM_FORMAT_* */ ++ u32 vc_image; /* VC_IMAGE_* */ ++ u32 is_vu; ++} vc_image_formats[] = { ++ { ++ .drm = DRM_FORMAT_XRGB8888, ++ .vc_image = VC_IMAGE_XRGB8888, ++ }, ++ { ++ .drm = DRM_FORMAT_ARGB8888, ++ .vc_image = VC_IMAGE_ARGB8888, ++ }, ++/* ++ * FIXME: Need to resolve which DRM format goes to which vc_image format ++ * for the remaining RGBA and RGBX formats. ++ * { ++ * .drm = DRM_FORMAT_ABGR8888, ++ * .vc_image = VC_IMAGE_RGBA8888, ++ * }, ++ * { ++ * .drm = DRM_FORMAT_XBGR8888, ++ * .vc_image = VC_IMAGE_RGBA8888, ++ * }, ++ */ ++ { ++ .drm = DRM_FORMAT_RGB565, ++ .vc_image = VC_IMAGE_RGB565, ++ }, ++ { ++ .drm = DRM_FORMAT_RGB888, ++ .vc_image = VC_IMAGE_BGR888, ++ }, ++ { ++ .drm = DRM_FORMAT_BGR888, ++ .vc_image = VC_IMAGE_RGB888, ++ }, ++ { ++ .drm = DRM_FORMAT_YUV422, ++ .vc_image = VC_IMAGE_YUV422PLANAR, ++ }, ++ { ++ .drm = DRM_FORMAT_YUV420, ++ .vc_image = VC_IMAGE_YUV420, ++ }, ++ { ++ .drm = DRM_FORMAT_YVU420, ++ .vc_image = VC_IMAGE_YUV420, ++ .is_vu = 1, ++ }, ++ { ++ .drm = DRM_FORMAT_NV12, ++ .vc_image = VC_IMAGE_YUV420SP, ++ }, ++ { ++ .drm = DRM_FORMAT_NV21, ++ .vc_image = VC_IMAGE_YUV420SP, ++ .is_vu = 1, ++ }, ++ { ++ .drm = DRM_FORMAT_P030, ++ .vc_image = VC_IMAGE_YUV10COL, ++ }, ++}; ++ ++static const struct vc_image_format *vc4_get_vc_image_fmt(u32 drm_format) ++{ ++ unsigned int i; ++ ++ for (i = 0; i < ARRAY_SIZE(vc_image_formats); i++) { ++ if (vc_image_formats[i].drm == drm_format) ++ return &vc_image_formats[i]; ++ } ++ ++ return NULL; ++} ++ ++/* The firmware delivers a vblank interrupt to us through the SMI ++ * hardware, which has only this one register. ++ */ ++#define SMICS 0x0 ++#define SMIDSW0 0x14 ++#define SMIDSW1 0x1C ++#define SMICS_INTERRUPTS (BIT(9) | BIT(10) | BIT(11)) ++ ++/* Flag to denote that the firmware is giving multiple display callbacks */ ++#define SMI_NEW 0xabcd0000 ++ ++#define vc4_crtc vc4_kms_crtc ++#define to_vc4_crtc to_vc4_kms_crtc ++struct vc4_crtc { ++ struct drm_crtc base; ++ struct drm_encoder *encoder; ++ struct drm_connector *connector; ++ void __iomem *regs; ++ ++ struct drm_pending_vblank_event *event; ++ bool vblank_enabled; ++ u32 display_number; ++ u32 display_type; ++}; ++ ++static inline struct vc4_crtc *to_vc4_crtc(struct drm_crtc *crtc) ++{ ++ return container_of(crtc, struct vc4_crtc, base); ++} ++ ++struct vc4_fkms_encoder { ++ struct drm_encoder base; ++ bool hdmi_monitor; ++ bool rgb_range_selectable; ++ int display_num; ++}; ++ ++static inline struct vc4_fkms_encoder * ++to_vc4_fkms_encoder(struct drm_encoder *encoder) ++{ ++ return container_of(encoder, struct vc4_fkms_encoder, base); ++} ++ ++/* "Broadcast RGB" property. ++ * Allows overriding of HDMI full or limited range RGB ++ */ ++#define VC4_BROADCAST_RGB_AUTO 0 ++#define VC4_BROADCAST_RGB_FULL 1 ++#define VC4_BROADCAST_RGB_LIMITED 2 ++ ++/* VC4 FKMS connector KMS struct */ ++struct vc4_fkms_connector { ++ struct drm_connector base; ++ ++ /* Since the connector is attached to just the one encoder, ++ * this is the reference to it so we can do the best_encoder() ++ * hook. ++ */ ++ struct drm_encoder *encoder; ++ struct vc4_dev *vc4_dev; ++ u32 display_number; ++ u32 display_type; ++ ++ struct drm_property *broadcast_rgb_property; ++}; ++ ++static inline struct vc4_fkms_connector * ++to_vc4_fkms_connector(struct drm_connector *connector) ++{ ++ return container_of(connector, struct vc4_fkms_connector, base); ++} ++ ++/* VC4 FKMS connector state */ ++struct vc4_fkms_connector_state { ++ struct drm_connector_state base; ++ ++ int broadcast_rgb; ++}; ++ ++#define to_vc4_fkms_connector_state(x) \ ++ container_of(x, struct vc4_fkms_connector_state, base) ++ ++static u32 vc4_get_display_type(u32 display_number) ++{ ++ const u32 display_types[] = { ++ /* The firmware display (DispmanX) IDs map to specific types in ++ * a fixed manner. ++ */ ++ DRM_MODE_ENCODER_DSI, /* MAIN_LCD - DSI or DPI */ ++ DRM_MODE_ENCODER_DSI, /* AUX_LCD */ ++ DRM_MODE_ENCODER_TMDS, /* HDMI0 */ ++ DRM_MODE_ENCODER_TVDAC, /* VEC */ ++ DRM_MODE_ENCODER_NONE, /* FORCE_LCD */ ++ DRM_MODE_ENCODER_NONE, /* FORCE_TV */ ++ DRM_MODE_ENCODER_NONE, /* FORCE_OTHER */ ++ DRM_MODE_ENCODER_TMDS, /* HDMI1 */ ++ DRM_MODE_ENCODER_NONE, /* FORCE_TV2 */ ++ }; ++ return display_number > ARRAY_SIZE(display_types) - 1 ? ++ DRM_MODE_ENCODER_NONE : display_types[display_number]; ++} ++ ++/* Firmware's structure for making an FB mbox call. */ ++struct fbinfo_s { ++ u32 xres, yres, xres_virtual, yres_virtual; ++ u32 pitch, bpp; ++ u32 xoffset, yoffset; ++ u32 base; ++ u32 screen_size; ++ u16 cmap[256]; ++}; ++ ++struct vc4_fkms_plane { ++ struct drm_plane base; ++ struct fbinfo_s *fbinfo; ++ dma_addr_t fbinfo_bus_addr; ++ u32 pitch; ++ struct mailbox_set_plane mb; ++}; ++ ++static inline struct vc4_fkms_plane *to_vc4_fkms_plane(struct drm_plane *plane) ++{ ++ return (struct vc4_fkms_plane *)plane; ++} ++ ++static int vc4_plane_set_blank(struct drm_plane *plane, bool blank) ++{ ++ struct vc4_dev *vc4 = to_vc4_dev(plane->dev); ++ struct vc4_fkms_plane *vc4_plane = to_vc4_fkms_plane(plane); ++ struct mailbox_set_plane blank_mb = { ++ .tag = { RPI_FIRMWARE_SET_PLANE, sizeof(struct set_plane), 0 }, ++ .plane = { ++ .display = vc4_plane->mb.plane.display, ++ .plane_id = vc4_plane->mb.plane.plane_id, ++ } ++ }; ++ static const char * const plane_types[] = { ++ "overlay", ++ "primary", ++ "cursor" ++ }; ++ int ret; ++ ++ DRM_DEBUG_ATOMIC("[PLANE:%d:%s] %s plane %s", ++ plane->base.id, plane->name, plane_types[plane->type], ++ blank ? "blank" : "unblank"); ++ ++ if (blank) ++ ret = rpi_firmware_property_list(vc4->firmware, &blank_mb, ++ sizeof(blank_mb)); ++ else ++ ret = rpi_firmware_property_list(vc4->firmware, &vc4_plane->mb, ++ sizeof(vc4_plane->mb)); ++ ++ WARN_ONCE(ret, "%s: firmware call failed. Please update your firmware", ++ __func__); ++ return ret; ++} ++ ++static void vc4_fkms_crtc_get_margins(struct drm_crtc_state *state, ++ unsigned int *left, unsigned int *right, ++ unsigned int *top, unsigned int *bottom) ++{ ++ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(state); ++ struct drm_connector_state *conn_state; ++ struct drm_connector *conn; ++ int i; ++ ++ *left = vc4_state->margins.left; ++ *right = vc4_state->margins.right; ++ *top = vc4_state->margins.top; ++ *bottom = vc4_state->margins.bottom; ++ ++ /* We have to interate over all new connector states because ++ * vc4_fkms_crtc_get_margins() might be called before ++ * vc4_fkms_crtc_atomic_check() which means margins info in ++ * vc4_crtc_state might be outdated. ++ */ ++ for_each_new_connector_in_state(state->state, conn, conn_state, i) { ++ if (conn_state->crtc != state->crtc) ++ continue; ++ ++ *left = conn_state->tv.margins.left; ++ *right = conn_state->tv.margins.right; ++ *top = conn_state->tv.margins.top; ++ *bottom = conn_state->tv.margins.bottom; ++ break; ++ } ++} ++ ++static int vc4_fkms_margins_adj(struct drm_plane_state *pstate, ++ struct set_plane *plane) ++{ ++ unsigned int left, right, top, bottom; ++ int adjhdisplay, adjvdisplay; ++ struct drm_crtc_state *crtc_state; ++ ++ crtc_state = drm_atomic_get_new_crtc_state(pstate->state, ++ pstate->crtc); ++ ++ vc4_fkms_crtc_get_margins(crtc_state, &left, &right, &top, &bottom); ++ ++ if (!left && !right && !top && !bottom) ++ return 0; ++ ++ if (left + right >= crtc_state->mode.hdisplay || ++ top + bottom >= crtc_state->mode.vdisplay) ++ return -EINVAL; ++ ++ adjhdisplay = crtc_state->mode.hdisplay - (left + right); ++ plane->dst_x = DIV_ROUND_CLOSEST(plane->dst_x * adjhdisplay, ++ (int)crtc_state->mode.hdisplay); ++ plane->dst_x += left; ++ if (plane->dst_x > (int)(crtc_state->mode.hdisplay - left)) ++ plane->dst_x = crtc_state->mode.hdisplay - left; ++ ++ adjvdisplay = crtc_state->mode.vdisplay - (top + bottom); ++ plane->dst_y = DIV_ROUND_CLOSEST(plane->dst_y * adjvdisplay, ++ (int)crtc_state->mode.vdisplay); ++ plane->dst_y += top; ++ if (plane->dst_y > (int)(crtc_state->mode.vdisplay - top)) ++ plane->dst_y = crtc_state->mode.vdisplay - top; ++ ++ plane->dst_w = DIV_ROUND_CLOSEST(plane->dst_w * adjhdisplay, ++ crtc_state->mode.hdisplay); ++ plane->dst_h = DIV_ROUND_CLOSEST(plane->dst_h * adjvdisplay, ++ crtc_state->mode.vdisplay); ++ ++ if (!plane->dst_w || !plane->dst_h) ++ return -EINVAL; ++ ++ return 0; ++} ++ ++static void vc4_plane_atomic_update(struct drm_plane *plane, ++ struct drm_plane_state *old_state) ++{ ++ struct drm_plane_state *state = plane->state; ++ ++ /* ++ * Do NOT set now, as we haven't checked if the crtc is active or not. ++ * Set from vc4_plane_set_blank instead. ++ * ++ * If the CRTC is on (or going to be on) and we're enabled, ++ * then unblank. Otherwise, stay blank until CRTC enable. ++ */ ++ if (state->crtc->state->active) ++ vc4_plane_set_blank(plane, false); ++} ++ ++static void vc4_plane_atomic_disable(struct drm_plane *plane, ++ struct drm_plane_state *old_state) ++{ ++ struct drm_plane_state *state = plane->state; ++ struct vc4_fkms_plane *vc4_plane = to_vc4_fkms_plane(plane); ++ ++ DRM_DEBUG_ATOMIC("[PLANE:%d:%s] plane disable %dx%d@%d +%d,%d\n", ++ plane->base.id, plane->name, ++ state->crtc_w, ++ state->crtc_h, ++ vc4_plane->mb.plane.vc_image_type, ++ state->crtc_x, ++ state->crtc_y); ++ vc4_plane_set_blank(plane, true); ++} ++ ++static bool plane_enabled(struct drm_plane_state *state) ++{ ++ return state->fb && state->crtc; ++} ++ ++static int vc4_plane_to_mb(struct drm_plane *plane, ++ struct mailbox_set_plane *mb, ++ struct drm_plane_state *state) ++{ ++ struct drm_framebuffer *fb = state->fb; ++ struct drm_gem_cma_object *bo = drm_fb_cma_get_gem_obj(fb, 0); ++ const struct drm_format_info *drm_fmt = fb->format; ++ const struct vc_image_format *vc_fmt = ++ vc4_get_vc_image_fmt(drm_fmt->format); ++ int num_planes = fb->format->num_planes; ++ unsigned int rotation; ++ ++ mb->plane.vc_image_type = vc_fmt->vc_image; ++ mb->plane.width = fb->width; ++ mb->plane.height = fb->height; ++ mb->plane.pitch = fb->pitches[0]; ++ mb->plane.src_w = state->src_w; ++ mb->plane.src_h = state->src_h; ++ mb->plane.src_x = state->src_x; ++ mb->plane.src_y = state->src_y; ++ mb->plane.dst_w = state->crtc_w; ++ mb->plane.dst_h = state->crtc_h; ++ mb->plane.dst_x = state->crtc_x; ++ mb->plane.dst_y = state->crtc_y; ++ mb->plane.alpha = state->alpha >> 8; ++ mb->plane.layer = state->normalized_zpos ? ++ state->normalized_zpos : -127; ++ mb->plane.num_planes = num_planes; ++ mb->plane.is_vu = vc_fmt->is_vu; ++ mb->plane.planes[0] = bo->paddr + fb->offsets[0]; ++ ++ rotation = drm_rotation_simplify(state->rotation, ++ DRM_MODE_ROTATE_0 | ++ DRM_MODE_REFLECT_X | ++ DRM_MODE_REFLECT_Y); ++ ++ mb->plane.transform = TRANSFORM_NO_ROTATE; ++ if (rotation & DRM_MODE_REFLECT_X) ++ mb->plane.transform |= TRANSFORM_FLIP_HRIZ; ++ if (rotation & DRM_MODE_REFLECT_Y) ++ mb->plane.transform |= TRANSFORM_FLIP_VERT; ++ ++ vc4_fkms_margins_adj(state, &mb->plane); ++ ++ if (num_planes > 1) { ++ /* Assume this must be YUV */ ++ /* Makes assumptions on the stride for the chroma planes as we ++ * can't easily plumb in non-standard pitches. ++ */ ++ mb->plane.planes[1] = bo->paddr + fb->offsets[1]; ++ if (num_planes > 2) ++ mb->plane.planes[2] = bo->paddr + fb->offsets[2]; ++ else ++ mb->plane.planes[2] = 0; ++ ++ /* Special case the YUV420 with U and V as line interleaved ++ * planes as we have special handling for that case. ++ */ ++ if (num_planes == 3 && ++ (fb->offsets[2] - fb->offsets[1]) == fb->pitches[1]) ++ mb->plane.vc_image_type = VC_IMAGE_YUV420_S; ++ ++ switch (state->color_encoding) { ++ default: ++ case DRM_COLOR_YCBCR_BT601: ++ if (state->color_range == DRM_COLOR_YCBCR_LIMITED_RANGE) ++ mb->plane.color_encoding = ++ VC_IMAGE_YUVINFO_CSC_ITUR_BT601; ++ else ++ mb->plane.color_encoding = ++ VC_IMAGE_YUVINFO_CSC_JPEG_JFIF; ++ break; ++ case DRM_COLOR_YCBCR_BT709: ++ /* Currently no support for a full range BT709 */ ++ mb->plane.color_encoding = ++ VC_IMAGE_YUVINFO_CSC_ITUR_BT709; ++ break; ++ case DRM_COLOR_YCBCR_BT2020: ++ /* Currently no support for a full range BT2020 */ ++ mb->plane.color_encoding = ++ VC_IMAGE_YUVINFO_CSC_REC_2020; ++ break; ++ } ++ } else { ++ mb->plane.planes[1] = 0; ++ mb->plane.planes[2] = 0; ++ } ++ mb->plane.planes[3] = 0; ++ ++ switch (fourcc_mod_broadcom_mod(fb->modifier)) { ++ case DRM_FORMAT_MOD_BROADCOM_VC4_T_TILED: ++ switch (mb->plane.vc_image_type) { ++ case VC_IMAGE_XRGB8888: ++ mb->plane.vc_image_type = VC_IMAGE_TF_RGBX32; ++ break; ++ case VC_IMAGE_ARGB8888: ++ mb->plane.vc_image_type = VC_IMAGE_TF_RGBA32; ++ break; ++ case VC_IMAGE_RGB565: ++ mb->plane.vc_image_type = VC_IMAGE_TF_RGB565; ++ break; ++ } ++ break; ++ case DRM_FORMAT_MOD_BROADCOM_SAND128: ++ switch (mb->plane.vc_image_type) { ++ case VC_IMAGE_YUV420SP: ++ mb->plane.vc_image_type = VC_IMAGE_YUV_UV; ++ break; ++ /* VC_IMAGE_YUV10COL could be included in here, but it is only ++ * valid as a SAND128 format, so the table at the top will have ++ * already set the correct format. ++ */ ++ } ++ /* Note that the column pitch is passed across in lines, not ++ * bytes. ++ */ ++ mb->plane.pitch = fourcc_mod_broadcom_param(fb->modifier); ++ break; ++ } ++ ++ DRM_DEBUG_ATOMIC("[PLANE:%d:%s] plane update %dx%d@%d +dst(%d,%d, %d,%d) +src(%d,%d, %d,%d) 0x%08x/%08x/%08x/%d, alpha %u zpos %u\n", ++ plane->base.id, plane->name, ++ mb->plane.width, ++ mb->plane.height, ++ mb->plane.vc_image_type, ++ state->crtc_x, ++ state->crtc_y, ++ state->crtc_w, ++ state->crtc_h, ++ mb->plane.src_x, ++ mb->plane.src_y, ++ mb->plane.src_w, ++ mb->plane.src_h, ++ mb->plane.planes[0], ++ mb->plane.planes[1], ++ mb->plane.planes[2], ++ fb->pitches[0], ++ state->alpha, ++ state->normalized_zpos); ++ ++ return 0; ++} ++ ++static int vc4_plane_atomic_check(struct drm_plane *plane, ++ struct drm_plane_state *state) ++{ ++ struct vc4_fkms_plane *vc4_plane = to_vc4_fkms_plane(plane); ++ ++ if (!plane_enabled(state)) ++ return 0; ++ ++ return vc4_plane_to_mb(plane, &vc4_plane->mb, state); ++} ++ ++/* Called during init to allocate the plane's atomic state. */ ++static void vc4_plane_reset(struct drm_plane *plane) ++{ ++ struct vc4_plane_state *vc4_state; ++ ++ WARN_ON(plane->state); ++ ++ vc4_state = kzalloc(sizeof(*vc4_state), GFP_KERNEL); ++ if (!vc4_state) ++ return; ++ ++ __drm_atomic_helper_plane_reset(plane, &vc4_state->base); ++} ++ ++static void vc4_plane_destroy(struct drm_plane *plane) ++{ ++ drm_plane_cleanup(plane); ++} ++ ++static bool vc4_fkms_format_mod_supported(struct drm_plane *plane, ++ uint32_t format, ++ uint64_t modifier) ++{ ++ /* Support T_TILING for RGB formats only. */ ++ switch (format) { ++ case DRM_FORMAT_XRGB8888: ++ case DRM_FORMAT_ARGB8888: ++ case DRM_FORMAT_RGB565: ++ switch (modifier) { ++ case DRM_FORMAT_MOD_BROADCOM_VC4_T_TILED: ++ case DRM_FORMAT_MOD_LINEAR: ++ return true; ++ default: ++ return false; ++ } ++ case DRM_FORMAT_NV12: ++ switch (fourcc_mod_broadcom_mod(modifier)) { ++ case DRM_FORMAT_MOD_LINEAR: ++ case DRM_FORMAT_MOD_BROADCOM_SAND128: ++ return true; ++ default: ++ return false; ++ } ++ case DRM_FORMAT_P030: ++ switch (fourcc_mod_broadcom_mod(modifier)) { ++ case DRM_FORMAT_MOD_BROADCOM_SAND128: ++ return true; ++ default: ++ return false; ++ } ++ case DRM_FORMAT_NV21: ++ case DRM_FORMAT_RGB888: ++ case DRM_FORMAT_BGR888: ++ case DRM_FORMAT_YUV422: ++ case DRM_FORMAT_YUV420: ++ case DRM_FORMAT_YVU420: ++ default: ++ return (modifier == DRM_FORMAT_MOD_LINEAR); ++ } ++} ++ ++static struct drm_plane_state *vc4_plane_duplicate_state(struct drm_plane *plane) ++{ ++ struct vc4_plane_state *vc4_state; ++ ++ if (WARN_ON(!plane->state)) ++ return NULL; ++ ++ vc4_state = kzalloc(sizeof(*vc4_state), GFP_KERNEL); ++ if (!vc4_state) ++ return NULL; ++ ++ __drm_atomic_helper_plane_duplicate_state(plane, &vc4_state->base); ++ ++ return &vc4_state->base; ++} ++ ++static const struct drm_plane_funcs vc4_plane_funcs = { ++ .update_plane = drm_atomic_helper_update_plane, ++ .disable_plane = drm_atomic_helper_disable_plane, ++ .destroy = vc4_plane_destroy, ++ .set_property = NULL, ++ .reset = vc4_plane_reset, ++ .atomic_duplicate_state = vc4_plane_duplicate_state, ++ .atomic_destroy_state = drm_atomic_helper_plane_destroy_state, ++ .format_mod_supported = vc4_fkms_format_mod_supported, ++}; ++ ++static const struct drm_plane_helper_funcs vc4_plane_helper_funcs = { ++ .prepare_fb = drm_gem_fb_prepare_fb, ++ .cleanup_fb = NULL, ++ .atomic_check = vc4_plane_atomic_check, ++ .atomic_update = vc4_plane_atomic_update, ++ .atomic_disable = vc4_plane_atomic_disable, ++}; ++ ++static struct drm_plane *vc4_fkms_plane_init(struct drm_device *dev, ++ enum drm_plane_type type, ++ u8 display_num, ++ u8 plane_id) ++{ ++ struct drm_plane *plane = NULL; ++ struct vc4_fkms_plane *vc4_plane; ++ u32 formats[ARRAY_SIZE(vc_image_formats)]; ++ unsigned int default_zpos = 0; ++ u32 num_formats = 0; ++ int ret = 0; ++ static const uint64_t modifiers[] = { ++ DRM_FORMAT_MOD_LINEAR, ++ /* VC4_T_TILED should come after linear, because we ++ * would prefer to scan out linear (less bus traffic). ++ */ ++ DRM_FORMAT_MOD_BROADCOM_VC4_T_TILED, ++ DRM_FORMAT_MOD_BROADCOM_SAND128, ++ DRM_FORMAT_MOD_INVALID, ++ }; ++ int i; ++ ++ vc4_plane = devm_kzalloc(dev->dev, sizeof(*vc4_plane), ++ GFP_KERNEL); ++ if (!vc4_plane) { ++ ret = -ENOMEM; ++ goto fail; ++ } ++ ++ for (i = 0; i < ARRAY_SIZE(vc_image_formats); i++) ++ formats[num_formats++] = vc_image_formats[i].drm; ++ ++ plane = &vc4_plane->base; ++ ret = drm_universal_plane_init(dev, plane, 0, ++ &vc4_plane_funcs, ++ formats, num_formats, modifiers, ++ type, NULL); ++ ++ /* FIXME: Do we need to be checking return values from all these calls? ++ */ ++ drm_plane_helper_add(plane, &vc4_plane_helper_funcs); ++ ++ drm_plane_create_alpha_property(plane); ++ drm_plane_create_rotation_property(plane, DRM_MODE_ROTATE_0, ++ DRM_MODE_ROTATE_0 | ++ DRM_MODE_ROTATE_180 | ++ DRM_MODE_REFLECT_X | ++ DRM_MODE_REFLECT_Y); ++ drm_plane_create_color_properties(plane, ++ BIT(DRM_COLOR_YCBCR_BT601) | ++ BIT(DRM_COLOR_YCBCR_BT709) | ++ BIT(DRM_COLOR_YCBCR_BT2020), ++ BIT(DRM_COLOR_YCBCR_LIMITED_RANGE) | ++ BIT(DRM_COLOR_YCBCR_FULL_RANGE), ++ DRM_COLOR_YCBCR_BT709, ++ DRM_COLOR_YCBCR_LIMITED_RANGE); ++ ++ /* ++ * Default frame buffer setup is with FB on -127, and raspistill etc ++ * tend to drop overlays on layer 2. Cursor plane was on layer +127. ++ * ++ * For F-KMS the mailbox call allows for a s8. ++ * Remap zpos 0 to -127 for the background layer, but leave all the ++ * other layers as requested by KMS. ++ */ ++ switch (type) { ++ default: ++ case DRM_PLANE_TYPE_PRIMARY: ++ default_zpos = 0; ++ break; ++ case DRM_PLANE_TYPE_OVERLAY: ++ default_zpos = 1; ++ break; ++ case DRM_PLANE_TYPE_CURSOR: ++ default_zpos = 2; ++ break; ++ } ++ drm_plane_create_zpos_property(plane, default_zpos, 0, 127); ++ ++ /* Prepare the static elements of the mailbox structure */ ++ vc4_plane->mb.tag.tag = RPI_FIRMWARE_SET_PLANE; ++ vc4_plane->mb.tag.buf_size = sizeof(struct set_plane); ++ vc4_plane->mb.tag.req_resp_size = 0; ++ vc4_plane->mb.plane.display = display_num; ++ vc4_plane->mb.plane.plane_id = plane_id; ++ vc4_plane->mb.plane.layer = default_zpos ? default_zpos : -127; ++ ++ return plane; ++fail: ++ if (plane) ++ vc4_plane_destroy(plane); ++ ++ return ERR_PTR(ret); ++} ++ ++static void vc4_crtc_mode_set_nofb(struct drm_crtc *crtc) ++{ ++ struct drm_device *dev = crtc->dev; ++ struct vc4_dev *vc4 = to_vc4_dev(dev); ++ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); ++ struct drm_display_mode *mode = &crtc->state->adjusted_mode; ++ struct vc4_fkms_encoder *vc4_encoder = ++ to_vc4_fkms_encoder(vc4_crtc->encoder); ++ struct mailbox_set_mode mb = { ++ .tag1 = { RPI_FIRMWARE_SET_TIMING, ++ sizeof(struct set_timings), 0}, ++ }; ++ union hdmi_infoframe frame; ++ int ret; ++ ++ ret = drm_hdmi_avi_infoframe_from_display_mode(&frame.avi, vc4_crtc->connector, mode); ++ if (ret < 0) { ++ DRM_ERROR("couldn't fill AVI infoframe\n"); ++ return; ++ } ++ ++ DRM_DEBUG_KMS("Setting mode for display num %u mode name %s, clk %d, h(disp %d, start %d, end %d, total %d, skew %d) v(disp %d, start %d, end %d, total %d, scan %d), vrefresh %d, par %u, flags 0x%04x\n", ++ vc4_crtc->display_number, mode->name, mode->clock, ++ mode->hdisplay, mode->hsync_start, mode->hsync_end, ++ mode->htotal, mode->hskew, mode->vdisplay, ++ mode->vsync_start, mode->vsync_end, mode->vtotal, ++ mode->vscan, drm_mode_vrefresh(mode), ++ mode->picture_aspect_ratio, mode->flags); ++ mb.timings.display = vc4_crtc->display_number; ++ ++ mb.timings.clock = mode->clock; ++ mb.timings.hdisplay = mode->hdisplay; ++ mb.timings.hsync_start = mode->hsync_start; ++ mb.timings.hsync_end = mode->hsync_end; ++ mb.timings.htotal = mode->htotal; ++ mb.timings.hskew = mode->hskew; ++ mb.timings.vdisplay = mode->vdisplay; ++ mb.timings.vsync_start = mode->vsync_start; ++ mb.timings.vsync_end = mode->vsync_end; ++ mb.timings.vtotal = mode->vtotal; ++ mb.timings.vscan = mode->vscan; ++ mb.timings.vrefresh = drm_mode_vrefresh(mode); ++ mb.timings.flags = 0; ++ if (mode->flags & DRM_MODE_FLAG_PHSYNC) ++ mb.timings.flags |= TIMINGS_FLAGS_H_SYNC_POS; ++ if (mode->flags & DRM_MODE_FLAG_PVSYNC) ++ mb.timings.flags |= TIMINGS_FLAGS_V_SYNC_POS; ++ ++ switch (frame.avi.picture_aspect) { ++ default: ++ case HDMI_PICTURE_ASPECT_NONE: ++ mb.timings.flags |= TIMINGS_FLAGS_ASPECT_NONE; ++ break; ++ case HDMI_PICTURE_ASPECT_4_3: ++ mb.timings.flags |= TIMINGS_FLAGS_ASPECT_4_3; ++ break; ++ case HDMI_PICTURE_ASPECT_16_9: ++ mb.timings.flags |= TIMINGS_FLAGS_ASPECT_16_9; ++ break; ++ case HDMI_PICTURE_ASPECT_64_27: ++ mb.timings.flags |= TIMINGS_FLAGS_ASPECT_64_27; ++ break; ++ case HDMI_PICTURE_ASPECT_256_135: ++ mb.timings.flags |= TIMINGS_FLAGS_ASPECT_256_135; ++ break; ++ } ++ ++ if (mode->flags & DRM_MODE_FLAG_INTERLACE) ++ mb.timings.flags |= TIMINGS_FLAGS_INTERLACE; ++ if (mode->flags & DRM_MODE_FLAG_DBLCLK) ++ mb.timings.flags |= TIMINGS_FLAGS_DBL_CLK; ++ ++ mb.timings.video_id_code = frame.avi.video_code; ++ ++ if (!vc4_encoder->hdmi_monitor) { ++ mb.timings.flags |= TIMINGS_FLAGS_DVI; ++ } else { ++ struct vc4_fkms_connector_state *conn_state = ++ to_vc4_fkms_connector_state(vc4_crtc->connector->state); ++ ++ if (conn_state->broadcast_rgb == VC4_BROADCAST_RGB_AUTO) { ++ /* See CEA-861-E - 5.1 Default Encoding Parameters */ ++ if (drm_default_rgb_quant_range(mode) == ++ HDMI_QUANTIZATION_RANGE_LIMITED) ++ mb.timings.flags |= TIMINGS_FLAGS_RGB_LIMITED; ++ } else { ++ if (conn_state->broadcast_rgb == ++ VC4_BROADCAST_RGB_LIMITED) ++ mb.timings.flags |= TIMINGS_FLAGS_RGB_LIMITED; ++ ++ /* If not using the default range, then do not provide ++ * a VIC as the HDMI spec requires that we do not ++ * signal the opposite of the defined range in the AVI ++ * infoframe. ++ */ ++ if (!!(mb.timings.flags & TIMINGS_FLAGS_RGB_LIMITED) != ++ (drm_default_rgb_quant_range(mode) == ++ HDMI_QUANTIZATION_RANGE_LIMITED)) ++ mb.timings.video_id_code = 0; ++ } ++ } ++ ++ /* ++ * FIXME: To implement ++ * switch(mode->flag & DRM_MODE_FLAG_3D_MASK) { ++ * case DRM_MODE_FLAG_3D_NONE: ++ * case DRM_MODE_FLAG_3D_FRAME_PACKING: ++ * case DRM_MODE_FLAG_3D_FIELD_ALTERNATIVE: ++ * case DRM_MODE_FLAG_3D_LINE_ALTERNATIVE: ++ * case DRM_MODE_FLAG_3D_SIDE_BY_SIDE_FULL: ++ * case DRM_MODE_FLAG_3D_L_DEPTH: ++ * case DRM_MODE_FLAG_3D_L_DEPTH_GFX_GFX_DEPTH: ++ * case DRM_MODE_FLAG_3D_TOP_AND_BOTTOM: ++ * case DRM_MODE_FLAG_3D_SIDE_BY_SIDE_HALF: ++ * } ++ */ ++ ++ ret = rpi_firmware_property_list(vc4->firmware, &mb, sizeof(mb)); ++} ++ ++static void vc4_crtc_disable(struct drm_crtc *crtc, ++ struct drm_atomic_state *state) ++{ ++ struct drm_device *dev = crtc->dev; ++ struct drm_plane *plane; ++ ++ DRM_DEBUG_KMS("[CRTC:%d] vblanks off.\n", ++ crtc->base.id); ++ drm_crtc_vblank_off(crtc); ++ ++ /* Always turn the planes off on CRTC disable. In DRM, planes ++ * are enabled/disabled through the update/disable hooks ++ * above, and the CRTC enable/disable independently controls ++ * whether anything scans out at all, but the firmware doesn't ++ * give us a CRTC-level control for that. ++ */ ++ ++ drm_atomic_crtc_for_each_plane(plane, crtc) ++ vc4_plane_atomic_disable(plane, plane->state); ++ ++ /* ++ * Make sure we issue a vblank event after disabling the CRTC if ++ * someone was waiting it. ++ */ ++ if (crtc->state->event) { ++ unsigned long flags; ++ ++ spin_lock_irqsave(&dev->event_lock, flags); ++ drm_crtc_send_vblank_event(crtc, crtc->state->event); ++ crtc->state->event = NULL; ++ spin_unlock_irqrestore(&dev->event_lock, flags); ++ } ++} ++ ++static void vc4_crtc_consume_event(struct drm_crtc *crtc) ++{ ++ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); ++ struct drm_device *dev = crtc->dev; ++ unsigned long flags; ++ ++ if (!crtc->state->event) ++ return; ++ ++ crtc->state->event->pipe = drm_crtc_index(crtc); ++ ++ WARN_ON(drm_crtc_vblank_get(crtc) != 0); ++ ++ spin_lock_irqsave(&dev->event_lock, flags); ++ vc4_crtc->event = crtc->state->event; ++ crtc->state->event = NULL; ++ spin_unlock_irqrestore(&dev->event_lock, flags); ++} ++ ++static void vc4_crtc_enable(struct drm_crtc *crtc, ++ struct drm_atomic_state *state) ++{ ++ struct drm_plane *plane; ++ ++ DRM_DEBUG_KMS("[CRTC:%d] vblanks on.\n", ++ crtc->base.id); ++ drm_crtc_vblank_on(crtc); ++ vc4_crtc_consume_event(crtc); ++ ++ /* Unblank the planes (if they're supposed to be displayed). */ ++ drm_atomic_crtc_for_each_plane(plane, crtc) ++ if (plane->state->fb) ++ vc4_plane_set_blank(plane, plane->state->visible); ++} ++ ++static enum drm_mode_status ++vc4_crtc_mode_valid(struct drm_crtc *crtc, const struct drm_display_mode *mode) ++{ ++ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); ++ struct drm_device *dev = crtc->dev; ++ struct vc4_dev *vc4 = to_vc4_dev(dev); ++ struct vc4_fkms *fkms = vc4->fkms; ++ ++ /* Do not allow doublescan modes from user space */ ++ if (mode->flags & DRM_MODE_FLAG_DBLSCAN) { ++ DRM_DEBUG_KMS("[CRTC:%d] Doublescan mode rejected.\n", ++ crtc->base.id); ++ return MODE_NO_DBLESCAN; ++ } ++ ++ /* Disable refresh rates > defined threshold (default 85Hz) as limited ++ * gain from them ++ */ ++ if (drm_mode_vrefresh(mode) > fkms_max_refresh_rate) ++ return MODE_BAD_VVALUE; ++ ++ /* Limit the pixel clock based on the HDMI clock limits from the ++ * firmware ++ */ ++ switch (vc4_crtc->display_number) { ++ case 2: /* HDMI0 */ ++ if (fkms->cfg.max_pixel_clock[0] && ++ mode->clock > fkms->cfg.max_pixel_clock[0]) ++ return MODE_CLOCK_HIGH; ++ break; ++ case 7: /* HDMI1 */ ++ if (fkms->cfg.max_pixel_clock[1] && ++ mode->clock > fkms->cfg.max_pixel_clock[1]) ++ return MODE_CLOCK_HIGH; ++ break; ++ } ++ ++ /* Pi4 can't generate odd horizontal timings on HDMI, so reject modes ++ * that would set them. ++ */ ++ if (fkms->bcm2711 && ++ (vc4_crtc->display_number == 2 || vc4_crtc->display_number == 7) && ++ !(mode->flags & DRM_MODE_FLAG_DBLCLK) && ++ ((mode->hdisplay | /* active */ ++ (mode->hsync_start - mode->hdisplay) | /* front porch */ ++ (mode->hsync_end - mode->hsync_start) | /* sync pulse */ ++ (mode->htotal - mode->hsync_end)) & 1)) /* back porch */ { ++ DRM_DEBUG_KMS("[CRTC:%d] Odd timing rejected %u %u %u %u.\n", ++ crtc->base.id, mode->hdisplay, mode->hsync_start, ++ mode->hsync_end, mode->htotal); ++ return MODE_H_ILLEGAL; ++ } ++ ++ return MODE_OK; ++} ++ ++static int vc4_crtc_atomic_check(struct drm_crtc *crtc, ++ struct drm_crtc_state *state) ++{ ++ struct vc4_crtc_state *vc4_state = to_vc4_crtc_state(state); ++ struct drm_connector *conn; ++ struct drm_connector_state *conn_state; ++ int i; ++ ++ DRM_DEBUG_KMS("[CRTC:%d] crtc_atomic_check.\n", crtc->base.id); ++ ++ for_each_new_connector_in_state(state->state, conn, conn_state, i) { ++ if (conn_state->crtc != crtc) ++ continue; ++ ++ vc4_state->margins.left = conn_state->tv.margins.left; ++ vc4_state->margins.right = conn_state->tv.margins.right; ++ vc4_state->margins.top = conn_state->tv.margins.top; ++ vc4_state->margins.bottom = conn_state->tv.margins.bottom; ++ break; ++ } ++ return 0; ++} ++ ++static void vc4_crtc_atomic_flush(struct drm_crtc *crtc, ++ struct drm_crtc_state *old_state) ++{ ++ DRM_DEBUG_KMS("[CRTC:%d] crtc_atomic_flush.\n", ++ crtc->base.id); ++ if (crtc->state->active && old_state->active && crtc->state->event) ++ vc4_crtc_consume_event(crtc); ++} ++ ++static void vc4_crtc_handle_page_flip(struct vc4_crtc *vc4_crtc) ++{ ++ struct drm_crtc *crtc = &vc4_crtc->base; ++ struct drm_device *dev = crtc->dev; ++ unsigned long flags; ++ ++ spin_lock_irqsave(&dev->event_lock, flags); ++ if (vc4_crtc->event) { ++ drm_crtc_send_vblank_event(crtc, vc4_crtc->event); ++ vc4_crtc->event = NULL; ++ drm_crtc_vblank_put(crtc); ++ } ++ spin_unlock_irqrestore(&dev->event_lock, flags); ++} ++ ++static irqreturn_t vc4_crtc_irq_handler(int irq, void *data) ++{ ++ struct vc4_crtc **crtc_list = data; ++ int i; ++ u32 stat = readl(crtc_list[0]->regs + SMICS); ++ irqreturn_t ret = IRQ_NONE; ++ u32 chan; ++ ++ if (stat & SMICS_INTERRUPTS) { ++ writel(0, crtc_list[0]->regs + SMICS); ++ ++ chan = readl(crtc_list[0]->regs + SMIDSW0); ++ ++ if ((chan & 0xFFFF0000) != SMI_NEW) { ++ /* Older firmware. Treat the one interrupt as vblank/ ++ * complete for all crtcs. ++ */ ++ for (i = 0; crtc_list[i]; i++) { ++ if (crtc_list[i]->vblank_enabled) ++ drm_crtc_handle_vblank(&crtc_list[i]->base); ++ vc4_crtc_handle_page_flip(crtc_list[i]); ++ } ++ } else { ++ if (chan & 1) { ++ writel(SMI_NEW, crtc_list[0]->regs + SMIDSW0); ++ if (crtc_list[0]->vblank_enabled) ++ drm_crtc_handle_vblank(&crtc_list[0]->base); ++ vc4_crtc_handle_page_flip(crtc_list[0]); ++ } ++ ++ if (crtc_list[1]) { ++ /* Check for the secondary display too */ ++ chan = readl(crtc_list[0]->regs + SMIDSW1); ++ ++ if (chan & 1) { ++ writel(SMI_NEW, crtc_list[0]->regs + SMIDSW1); ++ ++ if (crtc_list[1]->vblank_enabled) ++ drm_crtc_handle_vblank(&crtc_list[1]->base); ++ vc4_crtc_handle_page_flip(crtc_list[1]); ++ } ++ } ++ } ++ ++ ret = IRQ_HANDLED; ++ } ++ ++ return ret; ++} ++ ++static int vc4_fkms_page_flip(struct drm_crtc *crtc, ++ struct drm_framebuffer *fb, ++ struct drm_pending_vblank_event *event, ++ uint32_t flags, ++ struct drm_modeset_acquire_ctx *ctx) ++{ ++ if (flags & DRM_MODE_PAGE_FLIP_ASYNC) { ++ DRM_ERROR("Async flips aren't allowed\n"); ++ return -EINVAL; ++ } ++ ++ return drm_atomic_helper_page_flip(crtc, fb, event, flags, ctx); ++} ++ ++static struct drm_crtc_state * ++vc4_fkms_crtc_duplicate_state(struct drm_crtc *crtc) ++{ ++ struct vc4_crtc_state *vc4_state, *old_vc4_state; ++ ++ vc4_state = kzalloc(sizeof(*vc4_state), GFP_KERNEL); ++ if (!vc4_state) ++ return NULL; ++ ++ old_vc4_state = to_vc4_crtc_state(crtc->state); ++ vc4_state->margins = old_vc4_state->margins; ++ ++ __drm_atomic_helper_crtc_duplicate_state(crtc, &vc4_state->base); ++ return &vc4_state->base; ++} ++ ++static void ++vc4_fkms_crtc_reset(struct drm_crtc *crtc) ++{ ++ if (crtc->state) ++ __drm_atomic_helper_crtc_destroy_state(crtc->state); ++ ++ crtc->state = kzalloc(sizeof(*crtc->state), GFP_KERNEL); ++ if (crtc->state) ++ crtc->state->crtc = crtc; ++} ++ ++static int vc4_fkms_enable_vblank(struct drm_crtc *crtc) ++{ ++ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); ++ ++ DRM_DEBUG_KMS("[CRTC:%d] enable_vblank.\n", ++ crtc->base.id); ++ vc4_crtc->vblank_enabled = true; ++ ++ return 0; ++} ++ ++static void vc4_fkms_disable_vblank(struct drm_crtc *crtc) ++{ ++ struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); ++ ++ DRM_DEBUG_KMS("[CRTC:%d] disable_vblank.\n", ++ crtc->base.id); ++ vc4_crtc->vblank_enabled = false; ++} ++ ++static const struct drm_crtc_funcs vc4_crtc_funcs = { ++ .set_config = drm_atomic_helper_set_config, ++ .destroy = drm_crtc_cleanup, ++ .page_flip = vc4_fkms_page_flip, ++ .set_property = NULL, ++ .cursor_set = NULL, /* handled by drm_mode_cursor_universal */ ++ .cursor_move = NULL, /* handled by drm_mode_cursor_universal */ ++ .reset = vc4_fkms_crtc_reset, ++ .atomic_duplicate_state = vc4_fkms_crtc_duplicate_state, ++ .atomic_destroy_state = drm_atomic_helper_crtc_destroy_state, ++ .enable_vblank = vc4_fkms_enable_vblank, ++ .disable_vblank = vc4_fkms_disable_vblank, ++}; ++ ++static const struct drm_crtc_helper_funcs vc4_crtc_helper_funcs = { ++ .mode_set_nofb = vc4_crtc_mode_set_nofb, ++ .mode_valid = vc4_crtc_mode_valid, ++ .atomic_check = vc4_crtc_atomic_check, ++ .atomic_flush = vc4_crtc_atomic_flush, ++ .atomic_enable = vc4_crtc_enable, ++ .atomic_disable = vc4_crtc_disable, ++}; ++ ++static const struct of_device_id vc4_firmware_kms_dt_match[] = { ++ { .compatible = "raspberrypi,rpi-firmware-kms" }, ++ { .compatible = "raspberrypi,rpi-firmware-kms-2711", ++ .data = (void *)1 }, ++ {} ++}; ++ ++static enum drm_connector_status ++vc4_fkms_connector_detect(struct drm_connector *connector, bool force) ++{ ++ DRM_DEBUG_KMS("connector detect.\n"); ++ return connector_status_connected; ++} ++ ++/* Queries the firmware to populate a drm_mode structure for this display */ ++static int vc4_fkms_get_fw_mode(struct vc4_fkms_connector *fkms_connector, ++ struct drm_display_mode *mode) ++{ ++ struct vc4_dev *vc4 = fkms_connector->vc4_dev; ++ struct set_timings timings = { 0 }; ++ int ret; ++ ++ timings.display = fkms_connector->display_number; ++ ++ ret = rpi_firmware_property(vc4->firmware, ++ RPI_FIRMWARE_GET_DISPLAY_TIMING, &timings, ++ sizeof(timings)); ++ if (ret || !timings.clock) ++ /* No mode returned - abort */ ++ return -1; ++ ++ /* Equivalent to DRM_MODE macro. */ ++ memset(mode, 0, sizeof(*mode)); ++ strncpy(mode->name, "FIXED_MODE", sizeof(mode->name)); ++ mode->status = 0; ++ mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; ++ mode->clock = timings.clock; ++ mode->hdisplay = timings.hdisplay; ++ mode->hsync_start = timings.hsync_start; ++ mode->hsync_end = timings.hsync_end; ++ mode->htotal = timings.htotal; ++ mode->hskew = 0; ++ mode->vdisplay = timings.vdisplay; ++ mode->vsync_start = timings.vsync_start; ++ mode->vsync_end = timings.vsync_end; ++ mode->vtotal = timings.vtotal; ++ mode->vscan = timings.vscan; ++ ++ if (timings.flags & TIMINGS_FLAGS_H_SYNC_POS) ++ mode->flags |= DRM_MODE_FLAG_PHSYNC; ++ else ++ mode->flags |= DRM_MODE_FLAG_NHSYNC; ++ ++ if (timings.flags & TIMINGS_FLAGS_V_SYNC_POS) ++ mode->flags |= DRM_MODE_FLAG_PVSYNC; ++ else ++ mode->flags |= DRM_MODE_FLAG_NVSYNC; ++ ++ if (timings.flags & TIMINGS_FLAGS_INTERLACE) ++ mode->flags |= DRM_MODE_FLAG_INTERLACE; ++ ++ return 0; ++} ++ ++static int vc4_fkms_get_edid_block(void *data, u8 *buf, unsigned int block, ++ size_t len) ++{ ++ struct vc4_fkms_connector *fkms_connector = ++ (struct vc4_fkms_connector *)data; ++ struct vc4_dev *vc4 = fkms_connector->vc4_dev; ++ struct mailbox_get_edid mb = { ++ .tag1 = { RPI_FIRMWARE_GET_EDID_BLOCK_DISPLAY, ++ 128 + 8, 0 }, ++ .block = block, ++ .display_number = fkms_connector->display_number, ++ }; ++ int ret = 0; ++ ++ ret = rpi_firmware_property_list(vc4->firmware, &mb, sizeof(mb)); ++ ++ if (!ret) ++ memcpy(buf, mb.edid, len); ++ ++ return ret; ++} ++ ++static int vc4_fkms_connector_get_modes(struct drm_connector *connector) ++{ ++ struct vc4_fkms_connector *fkms_connector = ++ to_vc4_fkms_connector(connector); ++ struct drm_encoder *encoder = fkms_connector->encoder; ++ struct vc4_fkms_encoder *vc4_encoder = to_vc4_fkms_encoder(encoder); ++ struct drm_display_mode fw_mode; ++ struct drm_display_mode *mode; ++ struct edid *edid; ++ int num_modes; ++ ++ if (!vc4_fkms_get_fw_mode(fkms_connector, &fw_mode)) { ++ drm_mode_debug_printmodeline(&fw_mode); ++ mode = drm_mode_duplicate(connector->dev, ++ &fw_mode); ++ drm_mode_probed_add(connector, mode); ++ num_modes = 1; /* 1 mode */ ++ } else { ++ edid = drm_do_get_edid(connector, vc4_fkms_get_edid_block, ++ fkms_connector); ++ ++ /* FIXME: Can we do CEC? ++ * cec_s_phys_addr_from_edid(vc4->hdmi->cec_adap, edid); ++ * if (!edid) ++ * return -ENODEV; ++ */ ++ ++ vc4_encoder->hdmi_monitor = drm_detect_hdmi_monitor(edid); ++ ++ drm_connector_update_edid_property(connector, edid); ++ num_modes = drm_add_edid_modes(connector, edid); ++ kfree(edid); ++ } ++ ++ return num_modes; ++} ++ ++/* This is the DSI panel resolution. Use this as a default should the firmware ++ * not respond to our request for the timings. ++ */ ++static const struct drm_display_mode lcd_mode = { ++ DRM_MODE("800x480", DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED, ++ 25979400 / 1000, ++ 800, 800 + 1, 800 + 1 + 2, 800 + 1 + 2 + 46, 0, ++ 480, 480 + 7, 480 + 7 + 2, 480 + 7 + 2 + 21, 0, ++ 0) ++}; ++ ++static int vc4_fkms_lcd_connector_get_modes(struct drm_connector *connector) ++{ ++ struct vc4_fkms_connector *fkms_connector = ++ to_vc4_fkms_connector(connector); ++ struct drm_display_mode *mode; ++ struct drm_display_mode fw_mode; ++ ++ if (!vc4_fkms_get_fw_mode(fkms_connector, &fw_mode) && fw_mode.clock) ++ mode = drm_mode_duplicate(connector->dev, ++ &fw_mode); ++ else ++ mode = drm_mode_duplicate(connector->dev, ++ &lcd_mode); ++ ++ if (!mode) { ++ DRM_ERROR("Failed to create a new display mode\n"); ++ return -ENOMEM; ++ } ++ ++ drm_mode_probed_add(connector, mode); ++ ++ /* We have one mode */ ++ return 1; ++} ++ ++static struct drm_encoder * ++vc4_fkms_connector_best_encoder(struct drm_connector *connector) ++{ ++ struct vc4_fkms_connector *fkms_connector = ++ to_vc4_fkms_connector(connector); ++ DRM_DEBUG_KMS("best_connector.\n"); ++ return fkms_connector->encoder; ++} ++ ++static void vc4_fkms_connector_destroy(struct drm_connector *connector) ++{ ++ DRM_DEBUG_KMS("[CONNECTOR:%d] destroy.\n", ++ connector->base.id); ++ drm_connector_unregister(connector); ++ drm_connector_cleanup(connector); ++} ++ ++/** ++ * vc4_connector_duplicate_state - duplicate connector state ++ * @connector: digital connector ++ * ++ * Allocates and returns a copy of the connector state (both common and ++ * digital connector specific) for the specified connector. ++ * ++ * Returns: The newly allocated connector state, or NULL on failure. ++ */ ++struct drm_connector_state * ++vc4_connector_duplicate_state(struct drm_connector *connector) ++{ ++ struct vc4_fkms_connector_state *state; ++ ++ state = kmemdup(connector->state, sizeof(*state), GFP_KERNEL); ++ if (!state) ++ return NULL; ++ ++ __drm_atomic_helper_connector_duplicate_state(connector, &state->base); ++ return &state->base; ++} ++ ++/** ++ * vc4_connector_atomic_get_property - hook for connector->atomic_get_property. ++ * @connector: Connector to get the property for. ++ * @state: Connector state to retrieve the property from. ++ * @property: Property to retrieve. ++ * @val: Return value for the property. ++ * ++ * Returns the atomic property value for a digital connector. ++ */ ++int vc4_connector_atomic_get_property(struct drm_connector *connector, ++ const struct drm_connector_state *state, ++ struct drm_property *property, ++ uint64_t *val) ++{ ++ struct vc4_fkms_connector *fkms_connector = ++ to_vc4_fkms_connector(connector); ++ struct vc4_fkms_connector_state *vc4_conn_state = ++ to_vc4_fkms_connector_state(state); ++ ++ if (property == fkms_connector->broadcast_rgb_property) { ++ *val = vc4_conn_state->broadcast_rgb; ++ } else { ++ DRM_DEBUG_ATOMIC("Unknown property [PROP:%d:%s]\n", ++ property->base.id, property->name); ++ return -EINVAL; ++ } ++ ++ return 0; ++} ++ ++/** ++ * vc4_connector_atomic_set_property - hook for connector->atomic_set_property. ++ * @connector: Connector to set the property for. ++ * @state: Connector state to set the property on. ++ * @property: Property to set. ++ * @val: New value for the property. ++ * ++ * Sets the atomic property value for a digital connector. ++ */ ++int vc4_connector_atomic_set_property(struct drm_connector *connector, ++ struct drm_connector_state *state, ++ struct drm_property *property, ++ uint64_t val) ++{ ++ struct vc4_fkms_connector *fkms_connector = ++ to_vc4_fkms_connector(connector); ++ struct vc4_fkms_connector_state *vc4_conn_state = ++ to_vc4_fkms_connector_state(state); ++ ++ if (property == fkms_connector->broadcast_rgb_property) { ++ vc4_conn_state->broadcast_rgb = val; ++ return 0; ++ } ++ ++ DRM_DEBUG_ATOMIC("Unknown property [PROP:%d:%s]\n", ++ property->base.id, property->name); ++ return -EINVAL; ++} ++ ++static void vc4_hdmi_connector_reset(struct drm_connector *connector) ++{ ++ drm_atomic_helper_connector_reset(connector); ++ drm_atomic_helper_connector_tv_reset(connector); ++} ++ ++static const struct drm_connector_funcs vc4_fkms_connector_funcs = { ++ .detect = vc4_fkms_connector_detect, ++ .fill_modes = drm_helper_probe_single_connector_modes, ++ .destroy = vc4_fkms_connector_destroy, ++ .reset = vc4_hdmi_connector_reset, ++ .atomic_duplicate_state = vc4_connector_duplicate_state, ++ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, ++ .atomic_get_property = vc4_connector_atomic_get_property, ++ .atomic_set_property = vc4_connector_atomic_set_property, ++}; ++ ++static const struct drm_connector_helper_funcs vc4_fkms_connector_helper_funcs = { ++ .get_modes = vc4_fkms_connector_get_modes, ++ .best_encoder = vc4_fkms_connector_best_encoder, ++}; ++ ++static const struct drm_connector_helper_funcs vc4_fkms_lcd_conn_helper_funcs = { ++ .get_modes = vc4_fkms_lcd_connector_get_modes, ++ .best_encoder = vc4_fkms_connector_best_encoder, ++}; ++ ++static const struct drm_prop_enum_list broadcast_rgb_names[] = { ++ { VC4_BROADCAST_RGB_AUTO, "Automatic" }, ++ { VC4_BROADCAST_RGB_FULL, "Full" }, ++ { VC4_BROADCAST_RGB_LIMITED, "Limited 16:235" }, ++}; ++ ++static void ++vc4_attach_broadcast_rgb_property(struct vc4_fkms_connector *fkms_connector) ++{ ++ struct drm_device *dev = fkms_connector->base.dev; ++ struct drm_property *prop; ++ ++ prop = fkms_connector->broadcast_rgb_property; ++ if (!prop) { ++ prop = drm_property_create_enum(dev, DRM_MODE_PROP_ENUM, ++ "Broadcast RGB", ++ broadcast_rgb_names, ++ ARRAY_SIZE(broadcast_rgb_names)); ++ if (!prop) ++ return; ++ ++ fkms_connector->broadcast_rgb_property = prop; ++ } ++ ++ drm_object_attach_property(&fkms_connector->base.base, prop, 0); ++} ++ ++static struct drm_connector * ++vc4_fkms_connector_init(struct drm_device *dev, struct drm_encoder *encoder, ++ u32 display_num) ++{ ++ struct drm_connector *connector = NULL; ++ struct vc4_fkms_connector *fkms_connector; ++ struct vc4_fkms_connector_state *conn_state = NULL; ++ struct vc4_dev *vc4_dev = to_vc4_dev(dev); ++ int ret = 0; ++ ++ DRM_DEBUG_KMS("connector_init, display_num %u\n", display_num); ++ ++ fkms_connector = devm_kzalloc(dev->dev, sizeof(*fkms_connector), ++ GFP_KERNEL); ++ if (!fkms_connector) ++ return ERR_PTR(-ENOMEM); ++ ++ /* ++ * Allocate enough memory to hold vc4_fkms_connector_state, ++ */ ++ conn_state = kzalloc(sizeof(*conn_state), GFP_KERNEL); ++ if (!conn_state) { ++ kfree(fkms_connector); ++ return ERR_PTR(-ENOMEM); ++ } ++ ++ connector = &fkms_connector->base; ++ ++ fkms_connector->encoder = encoder; ++ fkms_connector->display_number = display_num; ++ fkms_connector->display_type = vc4_get_display_type(display_num); ++ fkms_connector->vc4_dev = vc4_dev; ++ ++ __drm_atomic_helper_connector_reset(connector, ++ &conn_state->base); ++ ++ if (fkms_connector->display_type == DRM_MODE_ENCODER_DSI) { ++ drm_connector_init(dev, connector, &vc4_fkms_connector_funcs, ++ DRM_MODE_CONNECTOR_DSI); ++ drm_connector_helper_add(connector, ++ &vc4_fkms_lcd_conn_helper_funcs); ++ connector->interlace_allowed = 0; ++ } else if (fkms_connector->display_type == DRM_MODE_ENCODER_TVDAC) { ++ drm_connector_init(dev, connector, &vc4_fkms_connector_funcs, ++ DRM_MODE_CONNECTOR_Composite); ++ drm_connector_helper_add(connector, ++ &vc4_fkms_lcd_conn_helper_funcs); ++ connector->interlace_allowed = 1; ++ } else { ++ drm_connector_init(dev, connector, &vc4_fkms_connector_funcs, ++ DRM_MODE_CONNECTOR_HDMIA); ++ drm_connector_helper_add(connector, ++ &vc4_fkms_connector_helper_funcs); ++ connector->interlace_allowed = 1; ++ } ++ ++ ret = drm_mode_create_tv_margin_properties(dev); ++ if (ret) ++ goto fail; ++ ++ drm_connector_attach_tv_margin_properties(connector); ++ ++ connector->polled = (DRM_CONNECTOR_POLL_CONNECT | ++ DRM_CONNECTOR_POLL_DISCONNECT); ++ ++ connector->doublescan_allowed = 0; ++ ++ vc4_attach_broadcast_rgb_property(fkms_connector); ++ ++ drm_connector_attach_encoder(connector, encoder); ++ ++ return connector; ++ ++ fail: ++ if (connector) ++ vc4_fkms_connector_destroy(connector); ++ ++ return ERR_PTR(ret); ++} ++ ++static void vc4_fkms_encoder_destroy(struct drm_encoder *encoder) ++{ ++ DRM_DEBUG_KMS("Encoder_destroy\n"); ++ drm_encoder_cleanup(encoder); ++} ++ ++static const struct drm_encoder_funcs vc4_fkms_encoder_funcs = { ++ .destroy = vc4_fkms_encoder_destroy, ++}; ++ ++static void vc4_fkms_display_power(struct drm_encoder *encoder, bool power) ++{ ++ struct vc4_fkms_encoder *vc4_encoder = to_vc4_fkms_encoder(encoder); ++ struct vc4_dev *vc4 = to_vc4_dev(encoder->dev); ++ ++ struct mailbox_display_pwr pwr = { ++ .tag1 = {RPI_FIRMWARE_SET_DISPLAY_POWER, 8, 0, }, ++ .display = vc4_encoder->display_num, ++ .state = power ? 1 : 0, ++ }; ++ ++ rpi_firmware_property_list(vc4->firmware, &pwr, sizeof(pwr)); ++} ++ ++static void vc4_fkms_encoder_enable(struct drm_encoder *encoder) ++{ ++ vc4_fkms_display_power(encoder, true); ++ DRM_DEBUG_KMS("Encoder_enable\n"); ++} ++ ++static void vc4_fkms_encoder_disable(struct drm_encoder *encoder) ++{ ++ vc4_fkms_display_power(encoder, false); ++ DRM_DEBUG_KMS("Encoder_disable\n"); ++} ++ ++static const struct drm_encoder_helper_funcs vc4_fkms_encoder_helper_funcs = { ++ .enable = vc4_fkms_encoder_enable, ++ .disable = vc4_fkms_encoder_disable, ++}; ++ ++static int vc4_fkms_create_screen(struct device *dev, struct drm_device *drm, ++ int display_idx, int display_ref, ++ struct vc4_crtc **ret_crtc) ++{ ++ struct vc4_dev *vc4 = to_vc4_dev(drm); ++ struct vc4_crtc *vc4_crtc; ++ struct vc4_fkms_encoder *vc4_encoder; ++ struct drm_crtc *crtc; ++ struct drm_plane *destroy_plane, *temp; ++ struct mailbox_blank_display blank = { ++ .tag1 = {RPI_FIRMWARE_FRAMEBUFFER_SET_DISPLAY_NUM, 4, 0, }, ++ .display = display_idx, ++ .tag2 = { RPI_FIRMWARE_FRAMEBUFFER_BLANK, 4, 0, }, ++ .blank = 1, ++ }; ++ struct drm_plane *planes[PLANES_PER_CRTC]; ++ int ret, i; ++ ++ vc4_crtc = devm_kzalloc(dev, sizeof(*vc4_crtc), GFP_KERNEL); ++ if (!vc4_crtc) ++ return -ENOMEM; ++ crtc = &vc4_crtc->base; ++ ++ vc4_crtc->display_number = display_ref; ++ vc4_crtc->display_type = vc4_get_display_type(display_ref); ++ ++ /* Blank the firmware provided framebuffer */ ++ rpi_firmware_property_list(vc4->firmware, &blank, sizeof(blank)); ++ ++ for (i = 0; i < PLANES_PER_CRTC; i++) { ++ planes[i] = vc4_fkms_plane_init(drm, ++ (i == 0) ? ++ DRM_PLANE_TYPE_PRIMARY : ++ (i == PLANES_PER_CRTC - 1) ? ++ DRM_PLANE_TYPE_CURSOR : ++ DRM_PLANE_TYPE_OVERLAY, ++ display_ref, ++ i + (display_idx * PLANES_PER_CRTC) ++ ); ++ if (IS_ERR(planes[i])) { ++ dev_err(dev, "failed to construct plane %u\n", i); ++ ret = PTR_ERR(planes[i]); ++ goto err; ++ } ++ } ++ ++ drm_crtc_init_with_planes(drm, crtc, planes[0], ++ planes[PLANES_PER_CRTC - 1], &vc4_crtc_funcs, ++ NULL); ++ drm_crtc_helper_add(crtc, &vc4_crtc_helper_funcs); ++ ++ /* Update the possible_crtcs mask for the overlay plane(s) */ ++ for (i = 1; i < (PLANES_PER_CRTC - 1); i++) ++ planes[i]->possible_crtcs = drm_crtc_mask(crtc); ++ ++ vc4_encoder = devm_kzalloc(dev, sizeof(*vc4_encoder), GFP_KERNEL); ++ if (!vc4_encoder) ++ return -ENOMEM; ++ vc4_crtc->encoder = &vc4_encoder->base; ++ ++ vc4_encoder->display_num = display_ref; ++ vc4_encoder->base.possible_crtcs |= drm_crtc_mask(crtc); ++ ++ drm_encoder_init(drm, &vc4_encoder->base, &vc4_fkms_encoder_funcs, ++ vc4_crtc->display_type, NULL); ++ drm_encoder_helper_add(&vc4_encoder->base, ++ &vc4_fkms_encoder_helper_funcs); ++ ++ vc4_crtc->connector = vc4_fkms_connector_init(drm, &vc4_encoder->base, ++ display_ref); ++ if (IS_ERR(vc4_crtc->connector)) { ++ ret = PTR_ERR(vc4_crtc->connector); ++ goto err_destroy_encoder; ++ } ++ ++ *ret_crtc = vc4_crtc; ++ ++ return 0; ++ ++err_destroy_encoder: ++ vc4_fkms_encoder_destroy(vc4_crtc->encoder); ++ list_for_each_entry_safe(destroy_plane, temp, ++ &drm->mode_config.plane_list, head) { ++ if (destroy_plane->possible_crtcs == 1 << drm_crtc_index(crtc)) ++ destroy_plane->funcs->destroy(destroy_plane); ++ } ++err: ++ return ret; ++} ++ ++static int vc4_fkms_bind(struct device *dev, struct device *master, void *data) ++{ ++ struct platform_device *pdev = to_platform_device(dev); ++ struct drm_device *drm = dev_get_drvdata(master); ++ struct vc4_dev *vc4 = to_vc4_dev(drm); ++ struct device_node *firmware_node; ++ const struct of_device_id *match; ++ struct vc4_crtc **crtc_list; ++ u32 num_displays, display_num; ++ struct vc4_fkms *fkms; ++ int ret; ++ u32 display_id; ++ ++ vc4->firmware_kms = true; ++ ++ fkms = devm_kzalloc(dev, sizeof(*fkms), GFP_KERNEL); ++ if (!fkms) ++ return -ENOMEM; ++ ++ match = of_match_device(vc4_firmware_kms_dt_match, dev); ++ if (!match) ++ return -ENODEV; ++ if (match->data) ++ fkms->bcm2711 = true; ++ ++ firmware_node = of_parse_phandle(dev->of_node, "brcm,firmware", 0); ++ vc4->firmware = rpi_firmware_get(firmware_node); ++ if (!vc4->firmware) { ++ DRM_DEBUG("Failed to get Raspberry Pi firmware reference.\n"); ++ return -EPROBE_DEFER; ++ } ++ of_node_put(firmware_node); ++ ++ ret = rpi_firmware_property(vc4->firmware, ++ RPI_FIRMWARE_FRAMEBUFFER_GET_NUM_DISPLAYS, ++ &num_displays, sizeof(u32)); ++ ++ /* If we fail to get the number of displays, then ++ * assume old firmware that doesn't have the mailbox call, so just ++ * set one display ++ */ ++ if (ret) { ++ num_displays = 1; ++ DRM_WARN("Unable to determine number of displays - assuming 1\n"); ++ ret = 0; ++ } ++ ++ ret = rpi_firmware_property(vc4->firmware, ++ RPI_FIRMWARE_GET_DISPLAY_CFG, ++ &fkms->cfg, sizeof(fkms->cfg)); ++ ++ if (ret) ++ return -EINVAL; ++ /* The firmware works in Hz. This will be compared against kHz, so div ++ * 1000 now rather than multiple times later. ++ */ ++ fkms->cfg.max_pixel_clock[0] /= 1000; ++ fkms->cfg.max_pixel_clock[1] /= 1000; ++ ++ /* Allocate a list, with space for a NULL on the end */ ++ crtc_list = devm_kzalloc(dev, sizeof(crtc_list) * (num_displays + 1), ++ GFP_KERNEL); ++ if (!crtc_list) ++ return -ENOMEM; ++ ++ for (display_num = 0; display_num < num_displays; display_num++) { ++ display_id = display_num; ++ ret = rpi_firmware_property(vc4->firmware, ++ RPI_FIRMWARE_FRAMEBUFFER_GET_DISPLAY_ID, ++ &display_id, sizeof(display_id)); ++ /* FIXME: Determine the correct error handling here. ++ * Should we fail to create the one "screen" but keep the ++ * others, or fail the whole thing? ++ */ ++ if (ret) ++ DRM_ERROR("Failed to get display id %u\n", display_num); ++ ++ ret = vc4_fkms_create_screen(dev, drm, display_num, display_id, ++ &crtc_list[display_num]); ++ if (ret) ++ DRM_ERROR("Oh dear, failed to create display %u\n", ++ display_num); ++ } ++ ++ if (num_displays > 0) { ++ /* Map the SMI interrupt reg */ ++ crtc_list[0]->regs = vc4_ioremap_regs(pdev, 0); ++ if (IS_ERR(crtc_list[0]->regs)) ++ DRM_ERROR("Oh dear, failed to map registers\n"); ++ ++ writel(0, crtc_list[0]->regs + SMICS); ++ ret = devm_request_irq(dev, platform_get_irq(pdev, 0), ++ vc4_crtc_irq_handler, 0, ++ "vc4 firmware kms", crtc_list); ++ if (ret) ++ DRM_ERROR("Oh dear, failed to register IRQ\n"); ++ } else { ++ DRM_WARN("No displays found. Consider forcing hotplug if HDMI is attached\n"); ++ } ++ ++ vc4->fkms = fkms; ++ ++ platform_set_drvdata(pdev, crtc_list); ++ ++ return 0; ++} ++ ++static void vc4_fkms_unbind(struct device *dev, struct device *master, ++ void *data) ++{ ++ struct platform_device *pdev = to_platform_device(dev); ++ struct vc4_crtc **crtc_list = dev_get_drvdata(dev); ++ int i; ++ ++ for (i = 0; crtc_list[i]; i++) { ++ vc4_fkms_connector_destroy(crtc_list[i]->connector); ++ vc4_fkms_encoder_destroy(crtc_list[i]->encoder); ++ drm_crtc_cleanup(&crtc_list[i]->base); ++ } ++ ++ platform_set_drvdata(pdev, NULL); ++} ++ ++static const struct component_ops vc4_fkms_ops = { ++ .bind = vc4_fkms_bind, ++ .unbind = vc4_fkms_unbind, ++}; ++ ++static int vc4_fkms_probe(struct platform_device *pdev) ++{ ++ return component_add(&pdev->dev, &vc4_fkms_ops); ++} ++ ++static int vc4_fkms_remove(struct platform_device *pdev) ++{ ++ component_del(&pdev->dev, &vc4_fkms_ops); ++ return 0; ++} ++ ++struct platform_driver vc4_firmware_kms_driver = { ++ .probe = vc4_fkms_probe, ++ .remove = vc4_fkms_remove, ++ .driver = { ++ .name = "vc4_firmware_kms", ++ .of_match_table = vc4_firmware_kms_dt_match, ++ }, ++}; +--- a/drivers/gpu/drm/vc4/vc4_kms.c ++++ b/drivers/gpu/drm/vc4/vc4_kms.c +@@ -154,6 +154,9 @@ vc4_ctm_commit(struct vc4_dev *vc4, stru + struct vc4_ctm_state *ctm_state = to_vc4_ctm_state(vc4->ctm_manager.state); + struct drm_color_ctm *ctm = ctm_state->ctm; + ++ if (vc4->firmware_kms) ++ return; ++ + if (ctm_state->fifo) { + HVS_WRITE(SCALER_OLEDCOEF2, + VC4_SET_FIELD(vc4_ctm_s31_32_to_s0_9(ctm->matrix[0]), +@@ -315,14 +318,14 @@ vc4_atomic_complete_commit(struct drm_at + for_each_new_crtc_in_state(state, crtc, new_crtc_state, i) { + struct vc4_crtc_state *vc4_crtc_state; + +- if (!new_crtc_state->commit) ++ if (!new_crtc_state->commit || vc4->firmware_kms) + continue; + + vc4_crtc_state = to_vc4_crtc_state(new_crtc_state); + vc4_hvs_mask_underrun(dev, vc4_crtc_state->assigned_channel); + } + +- if (vc4->hvs->hvs5) ++ if (vc4->hvs && vc4->hvs->hvs5) + clk_set_min_rate(hvs->core_clk, 500000000); + + drm_atomic_helper_wait_for_fences(dev, state, false); +@@ -333,10 +336,12 @@ vc4_atomic_complete_commit(struct drm_at + + vc4_ctm_commit(vc4, state); + +- if (vc4->hvs->hvs5) +- vc5_hvs_pv_muxing_commit(vc4, state); +- else +- vc4_hvs_pv_muxing_commit(vc4, state); ++ if (!vc4->firmware_kms) { ++ if (vc4->hvs->hvs5) ++ vc5_hvs_pv_muxing_commit(vc4, state); ++ else ++ vc4_hvs_pv_muxing_commit(vc4, state); ++ } + + drm_atomic_helper_commit_planes(dev, state, 0); + +@@ -352,7 +357,7 @@ vc4_atomic_complete_commit(struct drm_at + + drm_atomic_helper_commit_cleanup_done(state); + +- if (vc4->hvs->hvs5) ++ if (vc4->hvs && vc4->hvs->hvs5) + clk_set_min_rate(hvs->core_clk, 0); + + drm_atomic_state_put(state); +@@ -413,7 +418,8 @@ static int vc4_atomic_commit(struct drm_ + * drm_atomic_helper_setup_commit() from auto-completing + * commit->flip_done. + */ +- state->legacy_cursor_update = false; ++ if (!vc4->firmware_kms) ++ state->legacy_cursor_update = false; + ret = drm_atomic_helper_setup_commit(state, nonblock); + if (ret) + return ret; +@@ -778,6 +784,7 @@ static int vc4_hvs_channels_obj_init(str + static int vc4_pv_muxing_atomic_check(struct drm_device *dev, + struct drm_atomic_state *state) + { ++ struct vc4_dev *vc4 = to_vc4_dev(state->dev); + struct vc4_hvs_state *hvs_new_state; + struct drm_crtc_state *old_crtc_state, *new_crtc_state; + struct drm_crtc *crtc; +@@ -795,6 +802,9 @@ static int vc4_pv_muxing_atomic_check(st + struct vc4_crtc *vc4_crtc = to_vc4_crtc(crtc); + unsigned int matching_channels; + ++ if (vc4->firmware_kms) ++ continue; ++ + /* Nothing to do here, let's skip it */ + if (old_crtc_state->enable == new_crtc_state->enable) + continue; +@@ -913,6 +923,7 @@ int vc4_kms_load(struct drm_device *dev) + dev->mode_config.preferred_depth = 24; + dev->mode_config.async_page_flip = true; + dev->mode_config.allow_fb_modifiers = true; ++ dev->mode_config.normalize_zpos = true; + + ret = vc4_ctm_obj_init(vc4); + if (ret) +--- /dev/null ++++ b/drivers/gpu/drm/vc4/vc_image_types.h +@@ -0,0 +1,175 @@ ++ ++/* ++ * Copyright (c) 2012, Broadcom Europe Ltd ++ * ++ * Values taken from vc_image_types.h released by Broadcom at ++ * https://github.com/raspberrypi/userland/blob/master/interface/vctypes/vc_image_types.h ++ * and vc_image_structs.h at ++ * https://github.com/raspberrypi/userland/blob/master/interface/vctypes/vc_image_structs.h ++ * ++ * This program is free software; you can redistribute it and/or modify ++ * it under the terms of the GNU General Public License version 2 as ++ * published by the Free Software Foundation. ++ */ ++ ++enum { ++ VC_IMAGE_MIN = 0, //bounds for error checking ++ ++ VC_IMAGE_RGB565 = 1, ++ VC_IMAGE_1BPP, ++ VC_IMAGE_YUV420, ++ VC_IMAGE_48BPP, ++ VC_IMAGE_RGB888, ++ VC_IMAGE_8BPP, ++ /* 4bpp palettised image */ ++ VC_IMAGE_4BPP, ++ /* A separated format of 16 colour/light shorts followed by 16 z ++ * values ++ */ ++ VC_IMAGE_3D32, ++ /* 16 colours followed by 16 z values */ ++ VC_IMAGE_3D32B, ++ /* A separated format of 16 material/colour/light shorts followed by ++ * 16 z values ++ */ ++ VC_IMAGE_3D32MAT, ++ /* 32 bit format containing 18 bits of 6.6.6 RGB, 9 bits per short */ ++ VC_IMAGE_RGB2X9, ++ /* 32-bit format holding 18 bits of 6.6.6 RGB */ ++ VC_IMAGE_RGB666, ++ /* 4bpp palettised image with embedded palette */ ++ VC_IMAGE_PAL4_OBSOLETE, ++ /* 8bpp palettised image with embedded palette */ ++ VC_IMAGE_PAL8_OBSOLETE, ++ /* RGB888 with an alpha byte after each pixel */ ++ VC_IMAGE_RGBA32, ++ /* a line of Y (32-byte padded), a line of U (16-byte padded), and a ++ * line of V (16-byte padded) ++ */ ++ VC_IMAGE_YUV422, ++ /* RGB565 with a transparent patch */ ++ VC_IMAGE_RGBA565, ++ /* Compressed (4444) version of RGBA32 */ ++ VC_IMAGE_RGBA16, ++ /* VCIII codec format */ ++ VC_IMAGE_YUV_UV, ++ /* VCIII T-format RGBA8888 */ ++ VC_IMAGE_TF_RGBA32, ++ /* VCIII T-format RGBx8888 */ ++ VC_IMAGE_TF_RGBX32, ++ /* VCIII T-format float */ ++ VC_IMAGE_TF_FLOAT, ++ /* VCIII T-format RGBA4444 */ ++ VC_IMAGE_TF_RGBA16, ++ /* VCIII T-format RGB5551 */ ++ VC_IMAGE_TF_RGBA5551, ++ /* VCIII T-format RGB565 */ ++ VC_IMAGE_TF_RGB565, ++ /* VCIII T-format 8-bit luma and 8-bit alpha */ ++ VC_IMAGE_TF_YA88, ++ /* VCIII T-format 8 bit generic sample */ ++ VC_IMAGE_TF_BYTE, ++ /* VCIII T-format 8-bit palette */ ++ VC_IMAGE_TF_PAL8, ++ /* VCIII T-format 4-bit palette */ ++ VC_IMAGE_TF_PAL4, ++ /* VCIII T-format Ericsson Texture Compressed */ ++ VC_IMAGE_TF_ETC1, ++ /* RGB888 with R & B swapped */ ++ VC_IMAGE_BGR888, ++ /* RGB888 with R & B swapped, but with no pitch, i.e. no padding after ++ * each row of pixels ++ */ ++ VC_IMAGE_BGR888_NP, ++ /* Bayer image, extra defines which variant is being used */ ++ VC_IMAGE_BAYER, ++ /* General wrapper for codec images e.g. JPEG from camera */ ++ VC_IMAGE_CODEC, ++ /* VCIII codec format */ ++ VC_IMAGE_YUV_UV32, ++ /* VCIII T-format 8-bit luma */ ++ VC_IMAGE_TF_Y8, ++ /* VCIII T-format 8-bit alpha */ ++ VC_IMAGE_TF_A8, ++ /* VCIII T-format 16-bit generic sample */ ++ VC_IMAGE_TF_SHORT, ++ /* VCIII T-format 1bpp black/white */ ++ VC_IMAGE_TF_1BPP, ++ VC_IMAGE_OPENGL, ++ /* VCIII-B0 HVS YUV 4:4:4 interleaved samples */ ++ VC_IMAGE_YUV444I, ++ /* Y, U, & V planes separately (VC_IMAGE_YUV422 has them interleaved on ++ * a per line basis) ++ */ ++ VC_IMAGE_YUV422PLANAR, ++ /* 32bpp with 8bit alpha at MS byte, with R, G, B (LS byte) */ ++ VC_IMAGE_ARGB8888, ++ /* 32bpp with 8bit unused at MS byte, with R, G, B (LS byte) */ ++ VC_IMAGE_XRGB8888, ++ ++ /* interleaved 8 bit samples of Y, U, Y, V (4 flavours) */ ++ VC_IMAGE_YUV422YUYV, ++ VC_IMAGE_YUV422YVYU, ++ VC_IMAGE_YUV422UYVY, ++ VC_IMAGE_YUV422VYUY, ++ ++ /* 32bpp like RGBA32 but with unused alpha */ ++ VC_IMAGE_RGBX32, ++ /* 32bpp, corresponding to RGBA with unused alpha */ ++ VC_IMAGE_RGBX8888, ++ /* 32bpp, corresponding to BGRA with unused alpha */ ++ VC_IMAGE_BGRX8888, ++ ++ /* Y as a plane, then UV byte interleaved in plane with same pitch, ++ * half height ++ */ ++ VC_IMAGE_YUV420SP, ++ ++ /* Y, U, & V planes separately 4:4:4 */ ++ VC_IMAGE_YUV444PLANAR, ++ ++ /* T-format 8-bit U - same as TF_Y8 buf from U plane */ ++ VC_IMAGE_TF_U8, ++ /* T-format 8-bit U - same as TF_Y8 buf from V plane */ ++ VC_IMAGE_TF_V8, ++ ++ /* YUV4:2:0 planar, 16bit values */ ++ VC_IMAGE_YUV420_16, ++ /* YUV4:2:0 codec format, 16bit values */ ++ VC_IMAGE_YUV_UV_16, ++ /* YUV4:2:0 with U,V in side-by-side format */ ++ VC_IMAGE_YUV420_S, ++ /* 10-bit YUV 420 column image format */ ++ VC_IMAGE_YUV10COL, ++ /* 32-bpp, 10-bit R/G/B, 2-bit Alpha */ ++ VC_IMAGE_RGBA1010102, ++ ++ VC_IMAGE_MAX, /* bounds for error checking */ ++ VC_IMAGE_FORCE_ENUM_16BIT = 0xffff, ++}; ++ ++enum { ++ /* Unknown or unset - defaults to BT601 interstitial */ ++ VC_IMAGE_YUVINFO_UNSPECIFIED = 0, ++ ++ /* colour-space conversions data [4 bits] */ ++ ++ /* ITU-R BT.601-5 [SDTV] (compatible with VideoCore-II) */ ++ VC_IMAGE_YUVINFO_CSC_ITUR_BT601 = 1, ++ /* ITU-R BT.709-3 [HDTV] */ ++ VC_IMAGE_YUVINFO_CSC_ITUR_BT709 = 2, ++ /* JPEG JFIF */ ++ VC_IMAGE_YUVINFO_CSC_JPEG_JFIF = 3, ++ /* Title 47 Code of Federal Regulations (2003) 73.682 (a) (20) */ ++ VC_IMAGE_YUVINFO_CSC_FCC = 4, ++ /* Society of Motion Picture and Television Engineers 240M (1999) */ ++ VC_IMAGE_YUVINFO_CSC_SMPTE_240M = 5, ++ /* ITU-R BT.470-2 System M */ ++ VC_IMAGE_YUVINFO_CSC_ITUR_BT470_2_M = 6, ++ /* ITU-R BT.470-2 System B,G */ ++ VC_IMAGE_YUVINFO_CSC_ITUR_BT470_2_BG = 7, ++ /* JPEG JFIF, but with 16..255 luma */ ++ VC_IMAGE_YUVINFO_CSC_JPEG_JFIF_Y16_255 = 8, ++ /* Rec 2020 */ ++ VC_IMAGE_YUVINFO_CSC_REC_2020 = 9, ++}; +--- a/include/soc/bcm2835/raspberrypi-firmware.h ++++ b/include/soc/bcm2835/raspberrypi-firmware.h +@@ -75,6 +75,7 @@ enum rpi_firmware_property_tag { + RPI_FIRMWARE_GET_DISPMANX_RESOURCE_MEM_HANDLE = 0x00030014, + RPI_FIRMWARE_GET_EDID_BLOCK = 0x00030020, + RPI_FIRMWARE_GET_CUSTOMER_OTP = 0x00030021, ++ RPI_FIRMWARE_GET_EDID_BLOCK_DISPLAY = 0x00030023, + RPI_FIRMWARE_GET_DOMAIN_STATE = 0x00030030, + RPI_FIRMWARE_GET_THROTTLED = 0x00030046, + RPI_FIRMWARE_GET_CLOCK_MEASURED = 0x00030047, +@@ -148,6 +149,11 @@ enum rpi_firmware_property_tag { + + RPI_FIRMWARE_VCHIQ_INIT = 0x00048010, + ++ RPI_FIRMWARE_SET_PLANE = 0x00048015, ++ RPI_FIRMWARE_GET_DISPLAY_TIMING = 0x00040017, ++ RPI_FIRMWARE_SET_TIMING = 0x00048017, ++ RPI_FIRMWARE_GET_DISPLAY_CFG = 0x00040018, ++ RPI_FIRMWARE_SET_DISPLAY_POWER = 0x00048019, + RPI_FIRMWARE_GET_COMMAND_LINE = 0x00050001, + RPI_FIRMWARE_GET_DMA_CHANNELS = 0x00060001, + }; diff --git a/target/linux/bcm27xx/patches-5.10/950-0322-drm-vc4-Add-FKMS-as-an-acceptable-node-for-dma-range.patch b/target/linux/bcm27xx/patches-5.10/950-0322-drm-vc4-Add-FKMS-as-an-acceptable-node-for-dma-range.patch new file mode 100644 index 0000000000..d3f5582732 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0322-drm-vc4-Add-FKMS-as-an-acceptable-node-for-dma-range.patch @@ -0,0 +1,27 @@ +From 169f0a14f21a95194c5de355ce9a95d36aa97bef Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 19 May 2020 16:20:30 +0100 +Subject: [PATCH] drm/vc4: Add FKMS as an acceptable node for dma + ranges. + +Under FKMS, the firmware (via FKMS) also requires the VideoCore cache +aliases for image planes, as defined by the dma-ranges under /soc. + +Add rpi-firmware-kms to the list of acceptable nodes to look for +to copy dma config from. + +Signed-off-by: Dave Stevenson +--- + drivers/gpu/drm/vc4/vc4_drv.c | 1 + + 1 file changed, 1 insertion(+) + +--- a/drivers/gpu/drm/vc4/vc4_drv.c ++++ b/drivers/gpu/drm/vc4/vc4_drv.c +@@ -248,6 +248,7 @@ static void vc4_match_add_drivers(struct + + const struct of_device_id vc4_dma_range_matches[] = { + { .compatible = "brcm,bcm2835-hvs" }, ++ { .compatible = "raspberrypi,rpi-firmware-kms" }, + { .compatible = "brcm,bcm2835-v3d" }, + { .compatible = "brcm,cygnus-v3d" }, + { .compatible = "brcm,vc4-v3d" }, diff --git a/target/linux/bcm27xx/patches-5.10/950-0323-media-i2c-Add-driver-for-Sony-IMX477-sensor.patch b/target/linux/bcm27xx/patches-5.10/950-0323-media-i2c-Add-driver-for-Sony-IMX477-sensor.patch new file mode 100644 index 0000000000..bbfecb7ad6 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0323-media-i2c-Add-driver-for-Sony-IMX477-sensor.patch @@ -0,0 +1,2266 @@ +From 93582ca03e35b453e6da5c50a80339f5d00c3f05 Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Fri, 8 May 2020 10:00:12 +0100 +Subject: [PATCH] media: i2c: Add driver for Sony IMX477 sensor + +Adds a driver for the 12MPix Sony IMX477 CSI2 sensor. +Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver +currently only supports 2 lanes. + +The following Bayer modes are currently available: + +4056x3040 12-bit @ 10fps +2028x1520 12-bit (binned) @ 40fps +2028x1050 12-bit (cropped/binned) @ 50fps +1012x760 10-bit (scaled) @ 120 fps + +Signed-off-by: Naushir Patuck +--- + MAINTAINERS | 8 + + drivers/media/i2c/Kconfig | 11 + + drivers/media/i2c/Makefile | 1 + + drivers/media/i2c/imx477.c | 2191 ++++++++++++++++++++++++++++++++++++ + 4 files changed, 2211 insertions(+) + create mode 100644 drivers/media/i2c/imx477.c + +--- a/MAINTAINERS ++++ b/MAINTAINERS +@@ -16346,6 +16346,14 @@ S: Maintained + T: git git://linuxtv.org/media_tree.git + F: drivers/media/i2c/imx355.c + ++SONY IMX477 SENSOR DRIVER ++M: Raspberry Pi Kernel Maintenance ++L: linux-media@vger.kernel.org ++S: Maintained ++T: git git://linuxtv.org/media_tree.git ++F: Documentation/devicetree/bindings/media/i2c/imx477.yaml ++F: drivers/media/i2c/imx477.c ++ + SONY MEMORYSTICK SUBSYSTEM + M: Maxim Levitsky + M: Alex Dubov +--- a/drivers/media/i2c/Kconfig ++++ b/drivers/media/i2c/Kconfig +@@ -801,6 +801,17 @@ config VIDEO_IMX290 + To compile this driver as a module, choose M here: the + module will be called imx290. + ++config VIDEO_IMX477 ++ tristate "Sony IMX477 sensor support" ++ depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API ++ depends on MEDIA_CAMERA_SUPPORT ++ help ++ This is a Video4Linux2 sensor driver for the Sony ++ IMX477 camera. ++ ++ To compile this driver as a module, choose M here: the ++ module will be called imx477. ++ + config VIDEO_IMX319 + tristate "Sony IMX319 sensor support" + depends on I2C && VIDEO_V4L2 +--- a/drivers/media/i2c/Makefile ++++ b/drivers/media/i2c/Makefile +@@ -119,6 +119,7 @@ obj-$(CONFIG_VIDEO_IMX219) += imx219.o + obj-$(CONFIG_VIDEO_IMX258) += imx258.o + obj-$(CONFIG_VIDEO_IMX274) += imx274.o + obj-$(CONFIG_VIDEO_IMX290) += imx290.o ++obj-$(CONFIG_VIDEO_IMX477) += imx477.o + obj-$(CONFIG_VIDEO_IMX319) += imx319.o + obj-$(CONFIG_VIDEO_IMX355) += imx355.o + obj-$(CONFIG_VIDEO_MAX9286) += max9286.o +--- /dev/null ++++ b/drivers/media/i2c/imx477.c +@@ -0,0 +1,2191 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * A V4L2 driver for Sony IMX477 cameras. ++ * Copyright (C) 2020, Raspberry Pi (Trading) Ltd ++ * ++ * Based on Sony imx219 camera driver ++ * Copyright (C) 2019-2020 Raspberry Pi (Trading) Ltd ++ */ ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++#include ++ ++#define IMX477_REG_VALUE_08BIT 1 ++#define IMX477_REG_VALUE_16BIT 2 ++ ++/* Chip ID */ ++#define IMX477_REG_CHIP_ID 0x0016 ++#define IMX477_CHIP_ID 0x0477 ++ ++#define IMX477_REG_MODE_SELECT 0x0100 ++#define IMX477_MODE_STANDBY 0x00 ++#define IMX477_MODE_STREAMING 0x01 ++ ++#define IMX477_REG_ORIENTATION 0x101 ++ ++#define IMX477_XCLK_FREQ 24000000 ++ ++#define IMX477_DEFAULT_LINK_FREQ 450000000 ++ ++/* Pixel rate is fixed at 840MHz for all the modes */ ++#define IMX477_PIXEL_RATE 840000000 ++ ++/* V_TIMING internal */ ++#define IMX477_REG_FRAME_LENGTH 0x0340 ++#define IMX477_FRAME_LENGTH_MAX 0xffdc ++ ++/* Exposure control */ ++#define IMX477_REG_EXPOSURE 0x0202 ++#define IMX477_EXPOSURE_OFFSET 22 ++#define IMX477_EXPOSURE_MIN 20 ++#define IMX477_EXPOSURE_STEP 1 ++#define IMX477_EXPOSURE_DEFAULT 0x640 ++#define IMX477_EXPOSURE_MAX (IMX477_FRAME_LENGTH_MAX - \ ++ IMX477_EXPOSURE_OFFSET) ++ ++/* Analog gain control */ ++#define IMX477_REG_ANALOG_GAIN 0x0204 ++#define IMX477_ANA_GAIN_MIN 0 ++#define IMX477_ANA_GAIN_MAX 978 ++#define IMX477_ANA_GAIN_STEP 1 ++#define IMX477_ANA_GAIN_DEFAULT 0x0 ++ ++/* Digital gain control */ ++#define IMX477_REG_DIGITAL_GAIN 0x020e ++#define IMX477_DGTL_GAIN_MIN 0x0100 ++#define IMX477_DGTL_GAIN_MAX 0xffff ++#define IMX477_DGTL_GAIN_DEFAULT 0x0100 ++#define IMX477_DGTL_GAIN_STEP 1 ++ ++/* Test Pattern Control */ ++#define IMX477_REG_TEST_PATTERN 0x0600 ++#define IMX477_TEST_PATTERN_DISABLE 0 ++#define IMX477_TEST_PATTERN_SOLID_COLOR 1 ++#define IMX477_TEST_PATTERN_COLOR_BARS 2 ++#define IMX477_TEST_PATTERN_GREY_COLOR 3 ++#define IMX477_TEST_PATTERN_PN9 4 ++ ++/* Test pattern colour components */ ++#define IMX477_REG_TEST_PATTERN_R 0x0602 ++#define IMX477_REG_TEST_PATTERN_GR 0x0604 ++#define IMX477_REG_TEST_PATTERN_B 0x0606 ++#define IMX477_REG_TEST_PATTERN_GB 0x0608 ++#define IMX477_TEST_PATTERN_COLOUR_MIN 0 ++#define IMX477_TEST_PATTERN_COLOUR_MAX 0x0fff ++#define IMX477_TEST_PATTERN_COLOUR_STEP 1 ++#define IMX477_TEST_PATTERN_R_DEFAULT IMX477_TEST_PATTERN_COLOUR_MAX ++#define IMX477_TEST_PATTERN_GR_DEFAULT 0 ++#define IMX477_TEST_PATTERN_B_DEFAULT 0 ++#define IMX477_TEST_PATTERN_GB_DEFAULT 0 ++ ++/* Embedded metadata stream structure */ ++#define IMX477_EMBEDDED_LINE_WIDTH 16384 ++#define IMX477_NUM_EMBEDDED_LINES 1 ++ ++enum pad_types { ++ IMAGE_PAD, ++ METADATA_PAD, ++ NUM_PADS ++}; ++ ++/* IMX477 native and active pixel array size. */ ++#define IMX477_NATIVE_WIDTH 4072U ++#define IMX477_NATIVE_HEIGHT 3176U ++#define IMX477_PIXEL_ARRAY_LEFT 8U ++#define IMX477_PIXEL_ARRAY_TOP 16U ++#define IMX477_PIXEL_ARRAY_WIDTH 4056U ++#define IMX477_PIXEL_ARRAY_HEIGHT 3040U ++ ++struct imx477_reg { ++ u16 address; ++ u8 val; ++}; ++ ++struct imx477_reg_list { ++ unsigned int num_of_regs; ++ const struct imx477_reg *regs; ++}; ++ ++/* Mode : resolution and related config&values */ ++struct imx477_mode { ++ /* Frame width */ ++ unsigned int width; ++ ++ /* Frame height */ ++ unsigned int height; ++ ++ /* H-timing in pixels */ ++ unsigned int line_length_pix; ++ ++ /* Analog crop rectangle. */ ++ struct v4l2_rect crop; ++ ++ /* Highest possible framerate. */ ++ struct v4l2_fract timeperframe_min; ++ ++ /* Default framerate. */ ++ struct v4l2_fract timeperframe_default; ++ ++ /* Default register values */ ++ struct imx477_reg_list reg_list; ++}; ++ ++static const struct imx477_reg mode_common_regs[] = { ++ {0x0136, 0x18}, ++ {0x0137, 0x00}, ++ {0xe000, 0x00}, ++ {0xe07a, 0x01}, ++ {0x0808, 0x02}, ++ {0x4ae9, 0x18}, ++ {0x4aea, 0x08}, ++ {0xf61c, 0x04}, ++ {0xf61e, 0x04}, ++ {0x4ae9, 0x21}, ++ {0x4aea, 0x80}, ++ {0x38a8, 0x1f}, ++ {0x38a9, 0xff}, ++ {0x38aa, 0x1f}, ++ {0x38ab, 0xff}, ++ {0x55d4, 0x00}, ++ {0x55d5, 0x00}, ++ {0x55d6, 0x07}, ++ {0x55d7, 0xff}, ++ {0x55e8, 0x07}, ++ {0x55e9, 0xff}, ++ {0x55ea, 0x00}, ++ {0x55eb, 0x00}, ++ {0x574c, 0x07}, ++ {0x574d, 0xff}, ++ {0x574e, 0x00}, ++ {0x574f, 0x00}, ++ {0x5754, 0x00}, ++ {0x5755, 0x00}, ++ {0x5756, 0x07}, ++ {0x5757, 0xff}, ++ {0x5973, 0x04}, ++ {0x5974, 0x01}, ++ {0x5d13, 0xc3}, ++ {0x5d14, 0x58}, ++ {0x5d15, 0xa3}, ++ {0x5d16, 0x1d}, ++ {0x5d17, 0x65}, ++ {0x5d18, 0x8c}, ++ {0x5d1a, 0x06}, ++ {0x5d1b, 0xa9}, ++ {0x5d1c, 0x45}, ++ {0x5d1d, 0x3a}, ++ {0x5d1e, 0xab}, ++ {0x5d1f, 0x15}, ++ {0x5d21, 0x0e}, ++ {0x5d22, 0x52}, ++ {0x5d23, 0xaa}, ++ {0x5d24, 0x7d}, ++ {0x5d25, 0x57}, ++ {0x5d26, 0xa8}, ++ {0x5d37, 0x5a}, ++ {0x5d38, 0x5a}, ++ {0x5d77, 0x7f}, ++ {0x7b75, 0x0e}, ++ {0x7b76, 0x0b}, ++ {0x7b77, 0x08}, ++ {0x7b78, 0x0a}, ++ {0x7b79, 0x47}, ++ {0x7b7c, 0x00}, ++ {0x7b7d, 0x00}, ++ {0x8d1f, 0x00}, ++ {0x8d27, 0x00}, ++ {0x9004, 0x03}, ++ {0x9200, 0x50}, ++ {0x9201, 0x6c}, ++ {0x9202, 0x71}, ++ {0x9203, 0x00}, ++ {0x9204, 0x71}, ++ {0x9205, 0x01}, ++ {0x9371, 0x6a}, ++ {0x9373, 0x6a}, ++ {0x9375, 0x64}, ++ {0x991a, 0x00}, ++ {0x996b, 0x8c}, ++ {0x996c, 0x64}, ++ {0x996d, 0x50}, ++ {0x9a4c, 0x0d}, ++ {0x9a4d, 0x0d}, ++ {0xa001, 0x0a}, ++ {0xa003, 0x0a}, ++ {0xa005, 0x0a}, ++ {0xa006, 0x01}, ++ {0xa007, 0xc0}, ++ {0xa009, 0xc0}, ++ {0x3d8a, 0x01}, ++ {0x4421, 0x04}, ++ {0x7b3b, 0x01}, ++ {0x7b4c, 0x00}, ++ {0x9905, 0x00}, ++ {0x9907, 0x00}, ++ {0x9909, 0x00}, ++ {0x990b, 0x00}, ++ {0x9944, 0x3c}, ++ {0x9947, 0x3c}, ++ {0x994a, 0x8c}, ++ {0x994b, 0x50}, ++ {0x994c, 0x1b}, ++ {0x994d, 0x8c}, ++ {0x994e, 0x50}, ++ {0x994f, 0x1b}, ++ {0x9950, 0x8c}, ++ {0x9951, 0x1b}, ++ {0x9952, 0x0a}, ++ {0x9953, 0x8c}, ++ {0x9954, 0x1b}, ++ {0x9955, 0x0a}, ++ {0x9a13, 0x04}, ++ {0x9a14, 0x04}, ++ {0x9a19, 0x00}, ++ {0x9a1c, 0x04}, ++ {0x9a1d, 0x04}, ++ {0x9a26, 0x05}, ++ {0x9a27, 0x05}, ++ {0x9a2c, 0x01}, ++ {0x9a2d, 0x03}, ++ {0x9a2f, 0x05}, ++ {0x9a30, 0x05}, ++ {0x9a41, 0x00}, ++ {0x9a46, 0x00}, ++ {0x9a47, 0x00}, ++ {0x9c17, 0x35}, ++ {0x9c1d, 0x31}, ++ {0x9c29, 0x50}, ++ {0x9c3b, 0x2f}, ++ {0x9c41, 0x6b}, ++ {0x9c47, 0x2d}, ++ {0x9c4d, 0x40}, ++ {0x9c6b, 0x00}, ++ {0x9c71, 0xc8}, ++ {0x9c73, 0x32}, ++ {0x9c75, 0x04}, ++ {0x9c7d, 0x2d}, ++ {0x9c83, 0x40}, ++ {0x9c94, 0x3f}, ++ {0x9c95, 0x3f}, ++ {0x9c96, 0x3f}, ++ {0x9c97, 0x00}, ++ {0x9c98, 0x00}, ++ {0x9c99, 0x00}, ++ {0x9c9a, 0x3f}, ++ {0x9c9b, 0x3f}, ++ {0x9c9c, 0x3f}, ++ {0x9ca0, 0x0f}, ++ {0x9ca1, 0x0f}, ++ {0x9ca2, 0x0f}, ++ {0x9ca3, 0x00}, ++ {0x9ca4, 0x00}, ++ {0x9ca5, 0x00}, ++ {0x9ca6, 0x1e}, ++ {0x9ca7, 0x1e}, ++ {0x9ca8, 0x1e}, ++ {0x9ca9, 0x00}, ++ {0x9caa, 0x00}, ++ {0x9cab, 0x00}, ++ {0x9cac, 0x09}, ++ {0x9cad, 0x09}, ++ {0x9cae, 0x09}, ++ {0x9cbd, 0x50}, ++ {0x9cbf, 0x50}, ++ {0x9cc1, 0x50}, ++ {0x9cc3, 0x40}, ++ {0x9cc5, 0x40}, ++ {0x9cc7, 0x40}, ++ {0x9cc9, 0x0a}, ++ {0x9ccb, 0x0a}, ++ {0x9ccd, 0x0a}, ++ {0x9d17, 0x35}, ++ {0x9d1d, 0x31}, ++ {0x9d29, 0x50}, ++ {0x9d3b, 0x2f}, ++ {0x9d41, 0x6b}, ++ {0x9d47, 0x42}, ++ {0x9d4d, 0x5a}, ++ {0x9d6b, 0x00}, ++ {0x9d71, 0xc8}, ++ {0x9d73, 0x32}, ++ {0x9d75, 0x04}, ++ {0x9d7d, 0x42}, ++ {0x9d83, 0x5a}, ++ {0x9d94, 0x3f}, ++ {0x9d95, 0x3f}, ++ {0x9d96, 0x3f}, ++ {0x9d97, 0x00}, ++ {0x9d98, 0x00}, ++ {0x9d99, 0x00}, ++ {0x9d9a, 0x3f}, ++ {0x9d9b, 0x3f}, ++ {0x9d9c, 0x3f}, ++ {0x9d9d, 0x1f}, ++ {0x9d9e, 0x1f}, ++ {0x9d9f, 0x1f}, ++ {0x9da0, 0x0f}, ++ {0x9da1, 0x0f}, ++ {0x9da2, 0x0f}, ++ {0x9da3, 0x00}, ++ {0x9da4, 0x00}, ++ {0x9da5, 0x00}, ++ {0x9da6, 0x1e}, ++ {0x9da7, 0x1e}, ++ {0x9da8, 0x1e}, ++ {0x9da9, 0x00}, ++ {0x9daa, 0x00}, ++ {0x9dab, 0x00}, ++ {0x9dac, 0x09}, ++ {0x9dad, 0x09}, ++ {0x9dae, 0x09}, ++ {0x9dc9, 0x0a}, ++ {0x9dcb, 0x0a}, ++ {0x9dcd, 0x0a}, ++ {0x9e17, 0x35}, ++ {0x9e1d, 0x31}, ++ {0x9e29, 0x50}, ++ {0x9e3b, 0x2f}, ++ {0x9e41, 0x6b}, ++ {0x9e47, 0x2d}, ++ {0x9e4d, 0x40}, ++ {0x9e6b, 0x00}, ++ {0x9e71, 0xc8}, ++ {0x9e73, 0x32}, ++ {0x9e75, 0x04}, ++ {0x9e94, 0x0f}, ++ {0x9e95, 0x0f}, ++ {0x9e96, 0x0f}, ++ {0x9e97, 0x00}, ++ {0x9e98, 0x00}, ++ {0x9e99, 0x00}, ++ {0x9ea0, 0x0f}, ++ {0x9ea1, 0x0f}, ++ {0x9ea2, 0x0f}, ++ {0x9ea3, 0x00}, ++ {0x9ea4, 0x00}, ++ {0x9ea5, 0x00}, ++ {0x9ea6, 0x3f}, ++ {0x9ea7, 0x3f}, ++ {0x9ea8, 0x3f}, ++ {0x9ea9, 0x00}, ++ {0x9eaa, 0x00}, ++ {0x9eab, 0x00}, ++ {0x9eac, 0x09}, ++ {0x9ead, 0x09}, ++ {0x9eae, 0x09}, ++ {0x9ec9, 0x0a}, ++ {0x9ecb, 0x0a}, ++ {0x9ecd, 0x0a}, ++ {0x9f17, 0x35}, ++ {0x9f1d, 0x31}, ++ {0x9f29, 0x50}, ++ {0x9f3b, 0x2f}, ++ {0x9f41, 0x6b}, ++ {0x9f47, 0x42}, ++ {0x9f4d, 0x5a}, ++ {0x9f6b, 0x00}, ++ {0x9f71, 0xc8}, ++ {0x9f73, 0x32}, ++ {0x9f75, 0x04}, ++ {0x9f94, 0x0f}, ++ {0x9f95, 0x0f}, ++ {0x9f96, 0x0f}, ++ {0x9f97, 0x00}, ++ {0x9f98, 0x00}, ++ {0x9f99, 0x00}, ++ {0x9f9a, 0x2f}, ++ {0x9f9b, 0x2f}, ++ {0x9f9c, 0x2f}, ++ {0x9f9d, 0x00}, ++ {0x9f9e, 0x00}, ++ {0x9f9f, 0x00}, ++ {0x9fa0, 0x0f}, ++ {0x9fa1, 0x0f}, ++ {0x9fa2, 0x0f}, ++ {0x9fa3, 0x00}, ++ {0x9fa4, 0x00}, ++ {0x9fa5, 0x00}, ++ {0x9fa6, 0x1e}, ++ {0x9fa7, 0x1e}, ++ {0x9fa8, 0x1e}, ++ {0x9fa9, 0x00}, ++ {0x9faa, 0x00}, ++ {0x9fab, 0x00}, ++ {0x9fac, 0x09}, ++ {0x9fad, 0x09}, ++ {0x9fae, 0x09}, ++ {0x9fc9, 0x0a}, ++ {0x9fcb, 0x0a}, ++ {0x9fcd, 0x0a}, ++ {0xa14b, 0xff}, ++ {0xa151, 0x0c}, ++ {0xa153, 0x50}, ++ {0xa155, 0x02}, ++ {0xa157, 0x00}, ++ {0xa1ad, 0xff}, ++ {0xa1b3, 0x0c}, ++ {0xa1b5, 0x50}, ++ {0xa1b9, 0x00}, ++ {0xa24b, 0xff}, ++ {0xa257, 0x00}, ++ {0xa2ad, 0xff}, ++ {0xa2b9, 0x00}, ++ {0xb21f, 0x04}, ++ {0xb35c, 0x00}, ++ {0xb35e, 0x08}, ++ {0x0112, 0x0c}, ++ {0x0113, 0x0c}, ++ {0x0114, 0x01}, ++ {0x0350, 0x00}, ++ {0xbcf1, 0x02}, ++ {0x3ff9, 0x01}, ++}; ++ ++/* 12 mpix 10fps */ ++static const struct imx477_reg mode_4056x3040_regs[] = { ++ {0x0342, 0x5d}, ++ {0x0343, 0xc0}, ++ {0x0344, 0x00}, ++ {0x0345, 0x00}, ++ {0x0346, 0x00}, ++ {0x0347, 0x00}, ++ {0x0348, 0x0f}, ++ {0x0349, 0xd7}, ++ {0x034a, 0x0b}, ++ {0x034b, 0xdf}, ++ {0x00e3, 0x00}, ++ {0x00e4, 0x00}, ++ {0x00fc, 0x0a}, ++ {0x00fd, 0x0a}, ++ {0x00fe, 0x0a}, ++ {0x00ff, 0x0a}, ++ {0x0220, 0x00}, ++ {0x0221, 0x11}, ++ {0x0381, 0x01}, ++ {0x0383, 0x01}, ++ {0x0385, 0x01}, ++ {0x0387, 0x01}, ++ {0x0900, 0x00}, ++ {0x0901, 0x11}, ++ {0x0902, 0x02}, ++ {0x3140, 0x02}, ++ {0x3c00, 0x00}, ++ {0x3c01, 0x03}, ++ {0x3c02, 0xa2}, ++ {0x3f0d, 0x01}, ++ {0x5748, 0x07}, ++ {0x5749, 0xff}, ++ {0x574a, 0x00}, ++ {0x574b, 0x00}, ++ {0x7b75, 0x0a}, ++ {0x7b76, 0x0c}, ++ {0x7b77, 0x07}, ++ {0x7b78, 0x06}, ++ {0x7b79, 0x3c}, ++ {0x7b53, 0x01}, ++ {0x9369, 0x5a}, ++ {0x936b, 0x55}, ++ {0x936d, 0x28}, ++ {0x9304, 0x00}, ++ {0x9305, 0x00}, ++ {0x9e9a, 0x2f}, ++ {0x9e9b, 0x2f}, ++ {0x9e9c, 0x2f}, ++ {0x9e9d, 0x00}, ++ {0x9e9e, 0x00}, ++ {0x9e9f, 0x00}, ++ {0xa2a9, 0x60}, ++ {0xa2b7, 0x00}, ++ {0x0401, 0x00}, ++ {0x0404, 0x00}, ++ {0x0405, 0x10}, ++ {0x0408, 0x00}, ++ {0x0409, 0x00}, ++ {0x040a, 0x00}, ++ {0x040b, 0x00}, ++ {0x040c, 0x0f}, ++ {0x040d, 0xd8}, ++ {0x040e, 0x0b}, ++ {0x040f, 0xe0}, ++ {0x034c, 0x0f}, ++ {0x034d, 0xd8}, ++ {0x034e, 0x0b}, ++ {0x034f, 0xe0}, ++ {0x0301, 0x05}, ++ {0x0303, 0x02}, ++ {0x0305, 0x04}, ++ {0x0306, 0x01}, ++ {0x0307, 0x5e}, ++ {0x0309, 0x0c}, ++ {0x030b, 0x02}, ++ {0x030d, 0x02}, ++ {0x030e, 0x00}, ++ {0x030f, 0x96}, ++ {0x0310, 0x01}, ++ {0x0820, 0x07}, ++ {0x0821, 0x08}, ++ {0x0822, 0x00}, ++ {0x0823, 0x00}, ++ {0x080a, 0x00}, ++ {0x080b, 0x7f}, ++ {0x080c, 0x00}, ++ {0x080d, 0x4f}, ++ {0x080e, 0x00}, ++ {0x080f, 0x77}, ++ {0x0810, 0x00}, ++ {0x0811, 0x5f}, ++ {0x0812, 0x00}, ++ {0x0813, 0x57}, ++ {0x0814, 0x00}, ++ {0x0815, 0x4f}, ++ {0x0816, 0x01}, ++ {0x0817, 0x27}, ++ {0x0818, 0x00}, ++ {0x0819, 0x3f}, ++ {0xe04c, 0x00}, ++ {0xe04d, 0x7f}, ++ {0xe04e, 0x00}, ++ {0xe04f, 0x1f}, ++ {0x3e20, 0x01}, ++ {0x3e37, 0x00}, ++ {0x3f50, 0x00}, ++ {0x3f56, 0x02}, ++ {0x3f57, 0xae}, ++}; ++ ++/* 2x2 binned. 40fps */ ++static const struct imx477_reg mode_2028x1520_regs[] = { ++ {0x0342, 0x31}, ++ {0x0343, 0xc4}, ++ {0x0344, 0x00}, ++ {0x0345, 0x00}, ++ {0x0346, 0x00}, ++ {0x0347, 0x00}, ++ {0x0348, 0x0f}, ++ {0x0349, 0xd7}, ++ {0x034a, 0x0b}, ++ {0x034b, 0xdf}, ++ {0x0220, 0x00}, ++ {0x0221, 0x11}, ++ {0x0381, 0x01}, ++ {0x0383, 0x01}, ++ {0x0385, 0x01}, ++ {0x0387, 0x01}, ++ {0x0900, 0x01}, ++ {0x0901, 0x12}, ++ {0x0902, 0x02}, ++ {0x3140, 0x02}, ++ {0x3c00, 0x00}, ++ {0x3c01, 0x03}, ++ {0x3c02, 0xa2}, ++ {0x3f0d, 0x01}, ++ {0x5748, 0x07}, ++ {0x5749, 0xff}, ++ {0x574a, 0x00}, ++ {0x574b, 0x00}, ++ {0x7b53, 0x01}, ++ {0x9369, 0x73}, ++ {0x936b, 0x64}, ++ {0x936d, 0x5f}, ++ {0x9304, 0x00}, ++ {0x9305, 0x00}, ++ {0x9e9a, 0x2f}, ++ {0x9e9b, 0x2f}, ++ {0x9e9c, 0x2f}, ++ {0x9e9d, 0x00}, ++ {0x9e9e, 0x00}, ++ {0x9e9f, 0x00}, ++ {0xa2a9, 0x60}, ++ {0xa2b7, 0x00}, ++ {0x0401, 0x01}, ++ {0x0404, 0x00}, ++ {0x0405, 0x20}, ++ {0x0408, 0x00}, ++ {0x0409, 0x00}, ++ {0x040a, 0x00}, ++ {0x040b, 0x00}, ++ {0x040c, 0x0f}, ++ {0x040d, 0xd8}, ++ {0x040e, 0x0b}, ++ {0x040f, 0xe0}, ++ {0x034c, 0x07}, ++ {0x034d, 0xec}, ++ {0x034e, 0x05}, ++ {0x034f, 0xf0}, ++ {0x0301, 0x05}, ++ {0x0303, 0x02}, ++ {0x0305, 0x04}, ++ {0x0306, 0x01}, ++ {0x0307, 0x5e}, ++ {0x0309, 0x0c}, ++ {0x030b, 0x02}, ++ {0x030d, 0x02}, ++ {0x030e, 0x00}, ++ {0x030f, 0x96}, ++ {0x0310, 0x01}, ++ {0x0820, 0x07}, ++ {0x0821, 0x08}, ++ {0x0822, 0x00}, ++ {0x0823, 0x00}, ++ {0x080a, 0x00}, ++ {0x080b, 0x7f}, ++ {0x080c, 0x00}, ++ {0x080d, 0x4f}, ++ {0x080e, 0x00}, ++ {0x080f, 0x77}, ++ {0x0810, 0x00}, ++ {0x0811, 0x5f}, ++ {0x0812, 0x00}, ++ {0x0813, 0x57}, ++ {0x0814, 0x00}, ++ {0x0815, 0x4f}, ++ {0x0816, 0x01}, ++ {0x0817, 0x27}, ++ {0x0818, 0x00}, ++ {0x0819, 0x3f}, ++ {0xe04c, 0x00}, ++ {0xe04d, 0x7f}, ++ {0xe04e, 0x00}, ++ {0xe04f, 0x1f}, ++ {0x3e20, 0x01}, ++ {0x3e37, 0x00}, ++ {0x3f50, 0x00}, ++ {0x3f56, 0x01}, ++ {0x3f57, 0x6c}, ++}; ++ ++/* 1080p cropped mode */ ++static const struct imx477_reg mode_2028x1080_regs[] = { ++ {0x0342, 0x31}, ++ {0x0343, 0xc4}, ++ {0x0344, 0x00}, ++ {0x0345, 0x00}, ++ {0x0346, 0x01}, ++ {0x0347, 0xb8}, ++ {0x0348, 0x0f}, ++ {0x0349, 0xd7}, ++ {0x034a, 0x0a}, ++ {0x034b, 0x27}, ++ {0x0220, 0x00}, ++ {0x0221, 0x11}, ++ {0x0381, 0x01}, ++ {0x0383, 0x01}, ++ {0x0385, 0x01}, ++ {0x0387, 0x01}, ++ {0x0900, 0x01}, ++ {0x0901, 0x12}, ++ {0x0902, 0x02}, ++ {0x3140, 0x02}, ++ {0x3c00, 0x00}, ++ {0x3c01, 0x03}, ++ {0x3c02, 0xa2}, ++ {0x3f0d, 0x01}, ++ {0x5748, 0x07}, ++ {0x5749, 0xff}, ++ {0x574a, 0x00}, ++ {0x574b, 0x00}, ++ {0x7b53, 0x01}, ++ {0x9369, 0x73}, ++ {0x936b, 0x64}, ++ {0x936d, 0x5f}, ++ {0x9304, 0x00}, ++ {0x9305, 0x00}, ++ {0x9e9a, 0x2f}, ++ {0x9e9b, 0x2f}, ++ {0x9e9c, 0x2f}, ++ {0x9e9d, 0x00}, ++ {0x9e9e, 0x00}, ++ {0x9e9f, 0x00}, ++ {0xa2a9, 0x60}, ++ {0xa2b7, 0x00}, ++ {0x0401, 0x01}, ++ {0x0404, 0x00}, ++ {0x0405, 0x20}, ++ {0x0408, 0x00}, ++ {0x0409, 0x00}, ++ {0x040a, 0x00}, ++ {0x040b, 0x00}, ++ {0x040c, 0x0f}, ++ {0x040d, 0xd8}, ++ {0x040e, 0x04}, ++ {0x040f, 0x38}, ++ {0x034c, 0x07}, ++ {0x034d, 0xec}, ++ {0x034e, 0x04}, ++ {0x034f, 0x38}, ++ {0x0301, 0x05}, ++ {0x0303, 0x02}, ++ {0x0305, 0x04}, ++ {0x0306, 0x01}, ++ {0x0307, 0x5e}, ++ {0x0309, 0x0c}, ++ {0x030b, 0x02}, ++ {0x030d, 0x02}, ++ {0x030e, 0x00}, ++ {0x030f, 0x96}, ++ {0x0310, 0x01}, ++ {0x0820, 0x07}, ++ {0x0821, 0x08}, ++ {0x0822, 0x00}, ++ {0x0823, 0x00}, ++ {0x080a, 0x00}, ++ {0x080b, 0x7f}, ++ {0x080c, 0x00}, ++ {0x080d, 0x4f}, ++ {0x080e, 0x00}, ++ {0x080f, 0x77}, ++ {0x0810, 0x00}, ++ {0x0811, 0x5f}, ++ {0x0812, 0x00}, ++ {0x0813, 0x57}, ++ {0x0814, 0x00}, ++ {0x0815, 0x4f}, ++ {0x0816, 0x01}, ++ {0x0817, 0x27}, ++ {0x0818, 0x00}, ++ {0x0819, 0x3f}, ++ {0xe04c, 0x00}, ++ {0xe04d, 0x7f}, ++ {0xe04e, 0x00}, ++ {0xe04f, 0x1f}, ++ {0x3e20, 0x01}, ++ {0x3e37, 0x00}, ++ {0x3f50, 0x00}, ++ {0x3f56, 0x01}, ++ {0x3f57, 0x6c}, ++}; ++ ++/* 4x4 binned. 120fps */ ++static const struct imx477_reg mode_1012x760_regs[] = { ++ {0x420b, 0x01}, ++ {0x990c, 0x00}, ++ {0x990d, 0x08}, ++ {0x9956, 0x8c}, ++ {0x9957, 0x64}, ++ {0x9958, 0x50}, ++ {0x9a48, 0x06}, ++ {0x9a49, 0x06}, ++ {0x9a4a, 0x06}, ++ {0x9a4b, 0x06}, ++ {0x9a4c, 0x06}, ++ {0x9a4d, 0x06}, ++ {0x0112, 0x0a}, ++ {0x0113, 0x0a}, ++ {0x0114, 0x01}, ++ {0x0342, 0x14}, ++ {0x0343, 0x60}, ++ {0x0344, 0x00}, ++ {0x0345, 0x00}, ++ {0x0346, 0x00}, ++ {0x0347, 0x00}, ++ {0x0348, 0x0f}, ++ {0x0349, 0xd3}, ++ {0x034a, 0x0b}, ++ {0x034b, 0xdf}, ++ {0x00e3, 0x00}, ++ {0x00e4, 0x00}, ++ {0x00fc, 0x0a}, ++ {0x00fd, 0x0a}, ++ {0x00fe, 0x0a}, ++ {0x00ff, 0x0a}, ++ {0x0220, 0x00}, ++ {0x0221, 0x11}, ++ {0x0381, 0x01}, ++ {0x0383, 0x01}, ++ {0x0385, 0x01}, ++ {0x0387, 0x03}, ++ {0x0900, 0x01}, ++ {0x0901, 0x22}, ++ {0x0902, 0x02}, ++ {0x3140, 0x02}, ++ {0x3c00, 0x00}, ++ {0x3c01, 0x01}, ++ {0x3c02, 0x9c}, ++ {0x3f0d, 0x00}, ++ {0x5748, 0x00}, ++ {0x5749, 0x00}, ++ {0x574a, 0x00}, ++ {0x574b, 0xa4}, ++ {0x7b75, 0x0e}, ++ {0x7b76, 0x09}, ++ {0x7b77, 0x08}, ++ {0x7b78, 0x06}, ++ {0x7b79, 0x34}, ++ {0x7b53, 0x00}, ++ {0x9369, 0x73}, ++ {0x936b, 0x64}, ++ {0x936d, 0x5f}, ++ {0x9304, 0x03}, ++ {0x9305, 0x80}, ++ {0x9e9a, 0x3f}, ++ {0x9e9b, 0x3f}, ++ {0x9e9c, 0x3f}, ++ {0x9e9d, 0x27}, ++ {0x9e9e, 0x27}, ++ {0x9e9f, 0x27}, ++ {0xa2a9, 0x27}, ++ {0xa2b7, 0x03}, ++ {0x0401, 0x01}, ++ {0x0404, 0x00}, ++ {0x0405, 0x20}, ++ {0x0408, 0x00}, ++ {0x0409, 0x00}, ++ {0x040a, 0x00}, ++ {0x040b, 0x00}, ++ {0x040c, 0x07}, ++ {0x040d, 0xea}, ++ {0x040e, 0x02}, ++ {0x040f, 0xf8}, ++ {0x034c, 0x03}, ++ {0x034d, 0xf4}, ++ {0x034e, 0x02}, ++ {0x034f, 0xf8}, ++ {0x0301, 0x05}, ++ {0x0303, 0x02}, ++ {0x0305, 0x02}, ++ {0x0306, 0x00}, ++ {0x0307, 0xaf}, ++ {0x0309, 0x0a}, ++ {0x030b, 0x02}, ++ {0x030d, 0x02}, ++ {0x030e, 0x00}, ++ {0x030f, 0x96}, ++ {0x0310, 0x01}, ++ {0x0820, 0x07}, ++ {0x0821, 0x08}, ++ {0x0822, 0x00}, ++ {0x0823, 0x00}, ++ {0x080a, 0x00}, ++ {0x080b, 0x6f}, ++ {0x080c, 0x00}, ++ {0x080d, 0x3f}, ++ {0x080e, 0x00}, ++ {0x080f, 0xff}, ++ {0x0810, 0x00}, ++ {0x0811, 0x4f}, ++ {0x0812, 0x00}, ++ {0x0813, 0x47}, ++ {0x0814, 0x00}, ++ {0x0815, 0x37}, ++ {0x0816, 0x00}, ++ {0x0817, 0xe7}, ++ {0x0818, 0x00}, ++ {0x0819, 0x2f}, ++ {0xe04c, 0x00}, ++ {0xe04d, 0x5f}, ++ {0xe04e, 0x00}, ++ {0xe04f, 0x1f}, ++ {0x3e20, 0x01}, ++ {0x3e37, 0x00}, ++ {0x3f50, 0x00}, ++ {0x3f56, 0x00}, ++ {0x3f57, 0x96}, ++}; ++ ++/* Mode configs */ ++static const struct imx477_mode supported_modes_12bit[] = { ++ { ++ /* 12MPix 10fps mode */ ++ .width = 4056, ++ .height = 3040, ++ .line_length_pix = 0x5dc0, ++ .crop = { ++ .left = 0, ++ .top = 0, ++ .width = 4056, ++ .height = 3040, ++ }, ++ .timeperframe_min = { ++ .numerator = 100, ++ .denominator = 1000 ++ }, ++ .timeperframe_default = { ++ .numerator = 100, ++ .denominator = 1000 ++ }, ++ .reg_list = { ++ .num_of_regs = ARRAY_SIZE(mode_4056x3040_regs), ++ .regs = mode_4056x3040_regs, ++ }, ++ }, ++ { ++ /* 2x2 binned 40fps mode */ ++ .width = 2028, ++ .height = 1520, ++ .line_length_pix = 0x31c4, ++ .crop = { ++ .left = 0, ++ .top = 0, ++ .width = 4056, ++ .height = 3040, ++ }, ++ .timeperframe_min = { ++ .numerator = 100, ++ .denominator = 4000 ++ }, ++ .timeperframe_default = { ++ .numerator = 100, ++ .denominator = 3000 ++ }, ++ .reg_list = { ++ .num_of_regs = ARRAY_SIZE(mode_2028x1520_regs), ++ .regs = mode_2028x1520_regs, ++ }, ++ }, ++ { ++ /* 1080p 50fps cropped mode */ ++ .width = 2028, ++ .height = 1080, ++ .line_length_pix = 0x31c4, ++ .crop = { ++ .left = 0, ++ .top = 440, ++ .width = 4056, ++ .height = 2600, ++ }, ++ .timeperframe_min = { ++ .numerator = 100, ++ .denominator = 5000 ++ }, ++ .timeperframe_default = { ++ .numerator = 100, ++ .denominator = 3000 ++ }, ++ .reg_list = { ++ .num_of_regs = ARRAY_SIZE(mode_2028x1080_regs), ++ .regs = mode_2028x1080_regs, ++ }, ++ } ++}; ++ ++static const struct imx477_mode supported_modes_10bit[] = { ++ { ++ /* 720P 120fps. 4x4 binned */ ++ .width = 1012, ++ .height = 760, ++ .line_length_pix = 0x1460, ++ .crop = { ++ /* ++ * FIXME: the analog crop rectangle is actually ++ * programmed with a horizontal displacement of 0 ++ * pixels, not 4. It gets shrunk after going through ++ * the scaler. Move this information to the compose ++ * rectangle once the driver is expanded to represent ++ * its processing blocks with multiple subdevs. ++ */ ++ .left = 4, ++ .top = 0, ++ .width = 4052, ++ .height = 3040, ++ }, ++ .timeperframe_min = { ++ .numerator = 100, ++ .denominator = 12000 ++ }, ++ .timeperframe_default = { ++ .numerator = 100, ++ .denominator = 60000 ++ }, ++ .reg_list = { ++ .num_of_regs = ARRAY_SIZE(mode_1012x760_regs), ++ .regs = mode_1012x760_regs, ++ } ++ } ++}; ++ ++/* ++ * The supported formats. ++ * This table MUST contain 4 entries per format, to cover the various flip ++ * combinations in the order ++ * - no flip ++ * - h flip ++ * - v flip ++ * - h&v flips ++ */ ++static const u32 codes[] = { ++ /* 12-bit modes. */ ++ MEDIA_BUS_FMT_SRGGB12_1X12, ++ MEDIA_BUS_FMT_SGRBG12_1X12, ++ MEDIA_BUS_FMT_SGBRG12_1X12, ++ MEDIA_BUS_FMT_SBGGR12_1X12, ++ /* 10-bit modes. */ ++ MEDIA_BUS_FMT_SRGGB10_1X10, ++ MEDIA_BUS_FMT_SGRBG10_1X10, ++ MEDIA_BUS_FMT_SGBRG10_1X10, ++ MEDIA_BUS_FMT_SBGGR10_1X10, ++}; ++ ++static const char * const imx477_test_pattern_menu[] = { ++ "Disabled", ++ "Color Bars", ++ "Solid Color", ++ "Grey Color Bars", ++ "PN9" ++}; ++ ++static const int imx477_test_pattern_val[] = { ++ IMX477_TEST_PATTERN_DISABLE, ++ IMX477_TEST_PATTERN_COLOR_BARS, ++ IMX477_TEST_PATTERN_SOLID_COLOR, ++ IMX477_TEST_PATTERN_GREY_COLOR, ++ IMX477_TEST_PATTERN_PN9, ++}; ++ ++/* regulator supplies */ ++static const char * const imx477_supply_name[] = { ++ /* Supplies can be enabled in any order */ ++ "VANA", /* Analog (2.8V) supply */ ++ "VDIG", /* Digital Core (1.05V) supply */ ++ "VDDL", /* IF (1.8V) supply */ ++}; ++ ++#define IMX477_NUM_SUPPLIES ARRAY_SIZE(imx477_supply_name) ++ ++/* ++ * Initialisation delay between XCLR low->high and the moment when the sensor ++ * can start capture (i.e. can leave software standby), given by T7 in the ++ * datasheet is 8ms. This does include I2C setup time as well. ++ * ++ * Note, that delay between XCLR low->high and reading the CCI ID register (T6 ++ * in the datasheet) is much smaller - 600us. ++ */ ++#define IMX477_XCLR_MIN_DELAY_US 8000 ++#define IMX477_XCLR_DELAY_RANGE_US 1000 ++ ++struct imx477 { ++ struct v4l2_subdev sd; ++ struct media_pad pad[NUM_PADS]; ++ ++ struct v4l2_mbus_framefmt fmt; ++ ++ struct clk *xclk; ++ u32 xclk_freq; ++ ++ struct gpio_desc *reset_gpio; ++ struct regulator_bulk_data supplies[IMX477_NUM_SUPPLIES]; ++ ++ struct v4l2_ctrl_handler ctrl_handler; ++ /* V4L2 Controls */ ++ struct v4l2_ctrl *pixel_rate; ++ struct v4l2_ctrl *exposure; ++ struct v4l2_ctrl *vflip; ++ struct v4l2_ctrl *hflip; ++ struct v4l2_ctrl *vblank; ++ struct v4l2_ctrl *hblank; ++ ++ /* Current mode */ ++ const struct imx477_mode *mode; ++ ++ /* ++ * Mutex for serialized access: ++ * Protect sensor module set pad format and start/stop streaming safely. ++ */ ++ struct mutex mutex; ++ ++ /* Streaming on/off */ ++ bool streaming; ++ ++ /* Rewrite common registers on stream on? */ ++ bool common_regs_written; ++}; ++ ++static inline struct imx477 *to_imx477(struct v4l2_subdev *_sd) ++{ ++ return container_of(_sd, struct imx477, sd); ++} ++ ++static inline void get_mode_table(unsigned int code, ++ const struct imx477_mode **mode_list, ++ unsigned int *num_modes) ++{ ++ switch (code) { ++ /* 12-bit */ ++ case MEDIA_BUS_FMT_SRGGB12_1X12: ++ case MEDIA_BUS_FMT_SGRBG12_1X12: ++ case MEDIA_BUS_FMT_SGBRG12_1X12: ++ case MEDIA_BUS_FMT_SBGGR12_1X12: ++ *mode_list = supported_modes_12bit; ++ *num_modes = ARRAY_SIZE(supported_modes_12bit); ++ break; ++ /* 10-bit */ ++ case MEDIA_BUS_FMT_SRGGB10_1X10: ++ case MEDIA_BUS_FMT_SGRBG10_1X10: ++ case MEDIA_BUS_FMT_SGBRG10_1X10: ++ case MEDIA_BUS_FMT_SBGGR10_1X10: ++ *mode_list = supported_modes_10bit; ++ *num_modes = ARRAY_SIZE(supported_modes_10bit); ++ break; ++ default: ++ *mode_list = NULL; ++ *num_modes = 0; ++ } ++} ++ ++/* Read registers up to 2 at a time */ ++static int imx477_read_reg(struct imx477 *imx477, u16 reg, u32 len, u32 *val) ++{ ++ struct i2c_client *client = v4l2_get_subdevdata(&imx477->sd); ++ struct i2c_msg msgs[2]; ++ u8 addr_buf[2] = { reg >> 8, reg & 0xff }; ++ u8 data_buf[4] = { 0, }; ++ int ret; ++ ++ if (len > 4) ++ return -EINVAL; ++ ++ /* Write register address */ ++ msgs[0].addr = client->addr; ++ msgs[0].flags = 0; ++ msgs[0].len = ARRAY_SIZE(addr_buf); ++ msgs[0].buf = addr_buf; ++ ++ /* Read data from register */ ++ msgs[1].addr = client->addr; ++ msgs[1].flags = I2C_M_RD; ++ msgs[1].len = len; ++ msgs[1].buf = &data_buf[4 - len]; ++ ++ ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs)); ++ if (ret != ARRAY_SIZE(msgs)) ++ return -EIO; ++ ++ *val = get_unaligned_be32(data_buf); ++ ++ return 0; ++} ++ ++/* Write registers up to 2 at a time */ ++static int imx477_write_reg(struct imx477 *imx477, u16 reg, u32 len, u32 val) ++{ ++ struct i2c_client *client = v4l2_get_subdevdata(&imx477->sd); ++ u8 buf[6]; ++ ++ if (len > 4) ++ return -EINVAL; ++ ++ put_unaligned_be16(reg, buf); ++ put_unaligned_be32(val << (8 * (4 - len)), buf + 2); ++ if (i2c_master_send(client, buf, len + 2) != len + 2) ++ return -EIO; ++ ++ return 0; ++} ++ ++/* Write a list of registers */ ++static int imx477_write_regs(struct imx477 *imx477, ++ const struct imx477_reg *regs, u32 len) ++{ ++ struct i2c_client *client = v4l2_get_subdevdata(&imx477->sd); ++ unsigned int i; ++ int ret; ++ ++ for (i = 0; i < len; i++) { ++ ret = imx477_write_reg(imx477, regs[i].address, 1, regs[i].val); ++ if (ret) { ++ dev_err_ratelimited(&client->dev, ++ "Failed to write reg 0x%4.4x. error = %d\n", ++ regs[i].address, ret); ++ ++ return ret; ++ } ++ } ++ ++ return 0; ++} ++ ++/* Get bayer order based on flip setting. */ ++static u32 imx477_get_format_code(struct imx477 *imx477, u32 code) ++{ ++ unsigned int i; ++ ++ lockdep_assert_held(&imx477->mutex); ++ ++ for (i = 0; i < ARRAY_SIZE(codes); i++) ++ if (codes[i] == code) ++ break; ++ ++ if (i >= ARRAY_SIZE(codes)) ++ i = 0; ++ ++ i = (i & ~3) | (imx477->vflip->val ? 2 : 0) | ++ (imx477->hflip->val ? 1 : 0); ++ ++ return codes[i]; ++} ++ ++static void imx477_set_default_format(struct imx477 *imx477) ++{ ++ struct v4l2_mbus_framefmt *fmt = &imx477->fmt; ++ ++ /* Set default mode to max resolution */ ++ imx477->mode = &supported_modes_12bit[0]; ++ ++ fmt->code = MEDIA_BUS_FMT_SRGGB12_1X12; ++ fmt->colorspace = V4L2_COLORSPACE_SRGB; ++ fmt->ycbcr_enc = V4L2_MAP_YCBCR_ENC_DEFAULT(fmt->colorspace); ++ fmt->quantization = V4L2_MAP_QUANTIZATION_DEFAULT(true, ++ fmt->colorspace, ++ fmt->ycbcr_enc); ++ fmt->xfer_func = V4L2_MAP_XFER_FUNC_DEFAULT(fmt->colorspace); ++ fmt->width = imx477->mode->width; ++ fmt->height = imx477->mode->height; ++ fmt->field = V4L2_FIELD_NONE; ++} ++ ++static int imx477_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) ++{ ++ struct imx477 *imx477 = to_imx477(sd); ++ struct v4l2_mbus_framefmt *try_fmt_img = ++ v4l2_subdev_get_try_format(sd, fh->pad, IMAGE_PAD); ++ struct v4l2_mbus_framefmt *try_fmt_meta = ++ v4l2_subdev_get_try_format(sd, fh->pad, METADATA_PAD); ++ struct v4l2_rect *try_crop; ++ ++ mutex_lock(&imx477->mutex); ++ ++ /* Initialize try_fmt for the image pad */ ++ try_fmt_img->width = supported_modes_12bit[0].width; ++ try_fmt_img->height = supported_modes_12bit[0].height; ++ try_fmt_img->code = imx477_get_format_code(imx477, ++ MEDIA_BUS_FMT_SRGGB12_1X12); ++ try_fmt_img->field = V4L2_FIELD_NONE; ++ ++ /* Initialize try_fmt for the embedded metadata pad */ ++ try_fmt_meta->width = IMX477_EMBEDDED_LINE_WIDTH; ++ try_fmt_meta->height = IMX477_NUM_EMBEDDED_LINES; ++ try_fmt_meta->code = MEDIA_BUS_FMT_SENSOR_DATA; ++ try_fmt_meta->field = V4L2_FIELD_NONE; ++ ++ /* Initialize try_crop */ ++ try_crop = v4l2_subdev_get_try_crop(sd, fh->pad, IMAGE_PAD); ++ try_crop->left = IMX477_PIXEL_ARRAY_LEFT; ++ try_crop->top = IMX477_PIXEL_ARRAY_TOP; ++ try_crop->width = IMX477_PIXEL_ARRAY_WIDTH; ++ try_crop->height = IMX477_PIXEL_ARRAY_HEIGHT; ++ ++ mutex_unlock(&imx477->mutex); ++ ++ return 0; ++} ++ ++static int imx477_set_ctrl(struct v4l2_ctrl *ctrl) ++{ ++ struct imx477 *imx477 = ++ container_of(ctrl->handler, struct imx477, ctrl_handler); ++ struct i2c_client *client = v4l2_get_subdevdata(&imx477->sd); ++ int ret = 0; ++ ++ if (ctrl->id == V4L2_CID_VBLANK) { ++ int exposure_max, exposure_def; ++ ++ /* Update max exposure while meeting expected vblanking */ ++ exposure_max = imx477->mode->height + ctrl->val - ++ IMX477_EXPOSURE_OFFSET; ++ exposure_def = min(exposure_max, imx477->exposure->val); ++ __v4l2_ctrl_modify_range(imx477->exposure, ++ imx477->exposure->minimum, ++ exposure_max, imx477->exposure->step, ++ exposure_def); ++ } ++ ++ /* ++ * Applying V4L2 control value only happens ++ * when power is up for streaming ++ */ ++ if (pm_runtime_get_if_in_use(&client->dev) == 0) ++ return 0; ++ ++ switch (ctrl->id) { ++ case V4L2_CID_ANALOGUE_GAIN: ++ ret = imx477_write_reg(imx477, IMX477_REG_ANALOG_GAIN, ++ IMX477_REG_VALUE_16BIT, ctrl->val); ++ break; ++ case V4L2_CID_EXPOSURE: ++ ret = imx477_write_reg(imx477, IMX477_REG_EXPOSURE, ++ IMX477_REG_VALUE_16BIT, ctrl->val); ++ break; ++ case V4L2_CID_DIGITAL_GAIN: ++ ret = imx477_write_reg(imx477, IMX477_REG_DIGITAL_GAIN, ++ IMX477_REG_VALUE_16BIT, ctrl->val); ++ break; ++ case V4L2_CID_TEST_PATTERN: ++ ret = imx477_write_reg(imx477, IMX477_REG_TEST_PATTERN, ++ IMX477_REG_VALUE_16BIT, ++ imx477_test_pattern_val[ctrl->val]); ++ break; ++ case V4L2_CID_TEST_PATTERN_RED: ++ ret = imx477_write_reg(imx477, IMX477_REG_TEST_PATTERN_R, ++ IMX477_REG_VALUE_16BIT, ctrl->val); ++ break; ++ case V4L2_CID_TEST_PATTERN_GREENR: ++ ret = imx477_write_reg(imx477, IMX477_REG_TEST_PATTERN_GR, ++ IMX477_REG_VALUE_16BIT, ctrl->val); ++ break; ++ case V4L2_CID_TEST_PATTERN_BLUE: ++ ret = imx477_write_reg(imx477, IMX477_REG_TEST_PATTERN_B, ++ IMX477_REG_VALUE_16BIT, ctrl->val); ++ break; ++ case V4L2_CID_TEST_PATTERN_GREENB: ++ ret = imx477_write_reg(imx477, IMX477_REG_TEST_PATTERN_GB, ++ IMX477_REG_VALUE_16BIT, ctrl->val); ++ break; ++ case V4L2_CID_HFLIP: ++ case V4L2_CID_VFLIP: ++ ret = imx477_write_reg(imx477, IMX477_REG_ORIENTATION, 1, ++ imx477->hflip->val | ++ imx477->vflip->val << 1); ++ break; ++ case V4L2_CID_VBLANK: ++ ret = imx477_write_reg(imx477, IMX477_REG_FRAME_LENGTH, ++ IMX477_REG_VALUE_16BIT, ++ imx477->mode->height + ctrl->val); ++ break; ++ default: ++ dev_info(&client->dev, ++ "ctrl(id:0x%x,val:0x%x) is not handled\n", ++ ctrl->id, ctrl->val); ++ ret = -EINVAL; ++ break; ++ } ++ ++ pm_runtime_put(&client->dev); ++ ++ return ret; ++} ++ ++static const struct v4l2_ctrl_ops imx477_ctrl_ops = { ++ .s_ctrl = imx477_set_ctrl, ++}; ++ ++static int imx477_enum_mbus_code(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_mbus_code_enum *code) ++{ ++ struct imx477 *imx477 = to_imx477(sd); ++ ++ if (code->pad >= NUM_PADS) ++ return -EINVAL; ++ ++ if (code->pad == IMAGE_PAD) { ++ if (code->index >= (ARRAY_SIZE(codes) / 4)) ++ return -EINVAL; ++ ++ code->code = imx477_get_format_code(imx477, ++ codes[code->index * 4]); ++ } else { ++ if (code->index > 0) ++ return -EINVAL; ++ ++ code->code = MEDIA_BUS_FMT_SENSOR_DATA; ++ } ++ ++ return 0; ++} ++ ++static int imx477_enum_frame_size(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_frame_size_enum *fse) ++{ ++ struct imx477 *imx477 = to_imx477(sd); ++ ++ if (fse->pad >= NUM_PADS) ++ return -EINVAL; ++ ++ if (fse->pad == IMAGE_PAD) { ++ const struct imx477_mode *mode_list; ++ unsigned int num_modes; ++ ++ get_mode_table(fse->code, &mode_list, &num_modes); ++ ++ if (fse->index >= num_modes) ++ return -EINVAL; ++ ++ if (fse->code != imx477_get_format_code(imx477, fse->code)) ++ return -EINVAL; ++ ++ fse->min_width = mode_list[fse->index].width; ++ fse->max_width = fse->min_width; ++ fse->min_height = mode_list[fse->index].height; ++ fse->max_height = fse->min_height; ++ } else { ++ if (fse->code != MEDIA_BUS_FMT_SENSOR_DATA || fse->index > 0) ++ return -EINVAL; ++ ++ fse->min_width = IMX477_EMBEDDED_LINE_WIDTH; ++ fse->max_width = fse->min_width; ++ fse->min_height = IMX477_NUM_EMBEDDED_LINES; ++ fse->max_height = fse->min_height; ++ } ++ ++ return 0; ++} ++ ++static void imx477_reset_colorspace(struct v4l2_mbus_framefmt *fmt) ++{ ++ fmt->colorspace = V4L2_COLORSPACE_SRGB; ++ fmt->ycbcr_enc = V4L2_MAP_YCBCR_ENC_DEFAULT(fmt->colorspace); ++ fmt->quantization = V4L2_MAP_QUANTIZATION_DEFAULT(true, ++ fmt->colorspace, ++ fmt->ycbcr_enc); ++ fmt->xfer_func = V4L2_MAP_XFER_FUNC_DEFAULT(fmt->colorspace); ++} ++ ++static void imx477_update_image_pad_format(struct imx477 *imx477, ++ const struct imx477_mode *mode, ++ struct v4l2_subdev_format *fmt) ++{ ++ fmt->format.width = mode->width; ++ fmt->format.height = mode->height; ++ fmt->format.field = V4L2_FIELD_NONE; ++ imx477_reset_colorspace(&fmt->format); ++} ++ ++static void imx477_update_metadata_pad_format(struct v4l2_subdev_format *fmt) ++{ ++ fmt->format.width = IMX477_EMBEDDED_LINE_WIDTH; ++ fmt->format.height = IMX477_NUM_EMBEDDED_LINES; ++ fmt->format.code = MEDIA_BUS_FMT_SENSOR_DATA; ++ fmt->format.field = V4L2_FIELD_NONE; ++} ++ ++static int imx477_get_pad_format(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_format *fmt) ++{ ++ struct imx477 *imx477 = to_imx477(sd); ++ ++ if (fmt->pad >= NUM_PADS) ++ return -EINVAL; ++ ++ mutex_lock(&imx477->mutex); ++ ++ if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { ++ struct v4l2_mbus_framefmt *try_fmt = ++ v4l2_subdev_get_try_format(&imx477->sd, cfg, fmt->pad); ++ /* update the code which could change due to vflip or hflip: */ ++ try_fmt->code = fmt->pad == IMAGE_PAD ? ++ imx477_get_format_code(imx477, try_fmt->code) : ++ MEDIA_BUS_FMT_SENSOR_DATA; ++ fmt->format = *try_fmt; ++ } else { ++ if (fmt->pad == IMAGE_PAD) { ++ imx477_update_image_pad_format(imx477, imx477->mode, ++ fmt); ++ fmt->format.code = ++ imx477_get_format_code(imx477, imx477->fmt.code); ++ } else { ++ imx477_update_metadata_pad_format(fmt); ++ } ++ } ++ ++ mutex_unlock(&imx477->mutex); ++ return 0; ++} ++ ++static ++unsigned int imx477_get_frame_length(const struct imx477_mode *mode, ++ const struct v4l2_fract *timeperframe) ++{ ++ u64 frame_length; ++ ++ frame_length = (u64)timeperframe->numerator * IMX477_PIXEL_RATE; ++ do_div(frame_length, ++ (u64)timeperframe->denominator * mode->line_length_pix); ++ ++ if (WARN_ON(frame_length > IMX477_FRAME_LENGTH_MAX)) ++ frame_length = IMX477_FRAME_LENGTH_MAX; ++ ++ return max_t(unsigned int, frame_length, mode->height); ++} ++ ++static void imx477_set_framing_limits(struct imx477 *imx477) ++{ ++ const struct imx477_mode *mode = imx477->mode; ++ unsigned int frm_length_min, frm_length_default; ++ unsigned int exposure_max, exposure_def, hblank; ++ ++ frm_length_min = imx477_get_frame_length(mode, &mode->timeperframe_min); ++ frm_length_default = ++ imx477_get_frame_length(mode, &mode->timeperframe_default); ++ ++ /* Update limits and set FPS to default */ ++ __v4l2_ctrl_modify_range(imx477->vblank, frm_length_min - mode->height, ++ IMX477_FRAME_LENGTH_MAX - mode->height, ++ 1, frm_length_default - mode->height); ++ __v4l2_ctrl_s_ctrl(imx477->vblank, frm_length_default - mode->height); ++ ++ /* Update max exposure while meeting expected vblanking */ ++ exposure_max = IMX477_FRAME_LENGTH_MAX - IMX477_EXPOSURE_OFFSET; ++ exposure_def = frm_length_default - mode->height - ++ IMX477_EXPOSURE_OFFSET; ++ __v4l2_ctrl_modify_range(imx477->exposure, imx477->exposure->minimum, ++ exposure_max, imx477->exposure->step, ++ exposure_def); ++ /* ++ * Currently PPL is fixed to the mode specified value, so hblank ++ * depends on mode->width only, and is not changeable in any ++ * way other than changing the mode. ++ */ ++ hblank = mode->line_length_pix - mode->width; ++ __v4l2_ctrl_modify_range(imx477->hblank, hblank, hblank, 1, hblank); ++} ++ ++static int imx477_set_pad_format(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_format *fmt) ++{ ++ struct v4l2_mbus_framefmt *framefmt; ++ const struct imx477_mode *mode; ++ struct imx477 *imx477 = to_imx477(sd); ++ ++ if (fmt->pad >= NUM_PADS) ++ return -EINVAL; ++ ++ mutex_lock(&imx477->mutex); ++ ++ if (fmt->pad == IMAGE_PAD) { ++ const struct imx477_mode *mode_list; ++ unsigned int num_modes; ++ ++ /* Bayer order varies with flips */ ++ fmt->format.code = imx477_get_format_code(imx477, ++ fmt->format.code); ++ ++ get_mode_table(fmt->format.code, &mode_list, &num_modes); ++ ++ mode = v4l2_find_nearest_size(mode_list, ++ num_modes, ++ width, height, ++ fmt->format.width, ++ fmt->format.height); ++ imx477_update_image_pad_format(imx477, mode, fmt); ++ if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { ++ framefmt = v4l2_subdev_get_try_format(sd, cfg, ++ fmt->pad); ++ *framefmt = fmt->format; ++ } else { ++ imx477->mode = mode; ++ imx477_set_framing_limits(imx477); ++ } ++ } else { ++ if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { ++ framefmt = v4l2_subdev_get_try_format(sd, cfg, ++ fmt->pad); ++ *framefmt = fmt->format; ++ } else { ++ /* Only one embedded data mode is supported */ ++ imx477_update_metadata_pad_format(fmt); ++ } ++ } ++ ++ mutex_unlock(&imx477->mutex); ++ ++ return 0; ++} ++ ++static const struct v4l2_rect * ++__imx477_get_pad_crop(struct imx477 *imx477, struct v4l2_subdev_pad_config *cfg, ++ unsigned int pad, enum v4l2_subdev_format_whence which) ++{ ++ switch (which) { ++ case V4L2_SUBDEV_FORMAT_TRY: ++ return v4l2_subdev_get_try_crop(&imx477->sd, cfg, pad); ++ case V4L2_SUBDEV_FORMAT_ACTIVE: ++ return &imx477->mode->crop; ++ } ++ ++ return NULL; ++} ++ ++static int imx477_get_selection(struct v4l2_subdev *sd, ++ struct v4l2_subdev_pad_config *cfg, ++ struct v4l2_subdev_selection *sel) ++{ ++ switch (sel->target) { ++ case V4L2_SEL_TGT_CROP: { ++ struct imx477 *imx477 = to_imx477(sd); ++ ++ mutex_lock(&imx477->mutex); ++ sel->r = *__imx477_get_pad_crop(imx477, cfg, sel->pad, ++ sel->which); ++ mutex_unlock(&imx477->mutex); ++ ++ return 0; ++ } ++ ++ case V4L2_SEL_TGT_NATIVE_SIZE: ++ sel->r.left = 0; ++ sel->r.top = 0; ++ sel->r.width = IMX477_NATIVE_WIDTH; ++ sel->r.height = IMX477_NATIVE_HEIGHT; ++ ++ return 0; ++ ++ case V4L2_SEL_TGT_CROP_DEFAULT: ++ sel->r.left = IMX477_PIXEL_ARRAY_LEFT; ++ sel->r.top = IMX477_PIXEL_ARRAY_TOP; ++ sel->r.width = IMX477_PIXEL_ARRAY_WIDTH; ++ sel->r.height = IMX477_PIXEL_ARRAY_HEIGHT; ++ ++ return 0; ++ } ++ ++ return -EINVAL; ++} ++ ++/* Start streaming */ ++static int imx477_start_streaming(struct imx477 *imx477) ++{ ++ struct i2c_client *client = v4l2_get_subdevdata(&imx477->sd); ++ const struct imx477_reg_list *reg_list; ++ int ret; ++ ++ if (!imx477->common_regs_written) { ++ ret = imx477_write_regs(imx477, mode_common_regs, ++ ARRAY_SIZE(mode_common_regs)); ++ if (ret) { ++ dev_err(&client->dev, "%s failed to set common settings\n", ++ __func__); ++ return ret; ++ } ++ imx477->common_regs_written = true; ++ } ++ ++ /* Apply default values of current mode */ ++ reg_list = &imx477->mode->reg_list; ++ ret = imx477_write_regs(imx477, reg_list->regs, reg_list->num_of_regs); ++ if (ret) { ++ dev_err(&client->dev, "%s failed to set mode\n", __func__); ++ return ret; ++ } ++ ++ /* Apply customized values from user */ ++ ret = __v4l2_ctrl_handler_setup(imx477->sd.ctrl_handler); ++ if (ret) ++ return ret; ++ ++ /* set stream on register */ ++ return imx477_write_reg(imx477, IMX477_REG_MODE_SELECT, ++ IMX477_REG_VALUE_08BIT, IMX477_MODE_STREAMING); ++} ++ ++/* Stop streaming */ ++static void imx477_stop_streaming(struct imx477 *imx477) ++{ ++ struct i2c_client *client = v4l2_get_subdevdata(&imx477->sd); ++ int ret; ++ ++ /* set stream off register */ ++ ret = imx477_write_reg(imx477, IMX477_REG_MODE_SELECT, ++ IMX477_REG_VALUE_08BIT, IMX477_MODE_STANDBY); ++ if (ret) ++ dev_err(&client->dev, "%s failed to set stream\n", __func__); ++} ++ ++static int imx477_set_stream(struct v4l2_subdev *sd, int enable) ++{ ++ struct imx477 *imx477 = to_imx477(sd); ++ struct i2c_client *client = v4l2_get_subdevdata(sd); ++ int ret = 0; ++ ++ mutex_lock(&imx477->mutex); ++ if (imx477->streaming == enable) { ++ mutex_unlock(&imx477->mutex); ++ return 0; ++ } ++ ++ if (enable) { ++ ret = pm_runtime_get_sync(&client->dev); ++ if (ret < 0) { ++ pm_runtime_put_noidle(&client->dev); ++ goto err_unlock; ++ } ++ ++ /* ++ * Apply default & customized values ++ * and then start streaming. ++ */ ++ ret = imx477_start_streaming(imx477); ++ if (ret) ++ goto err_rpm_put; ++ } else { ++ imx477_stop_streaming(imx477); ++ pm_runtime_put(&client->dev); ++ } ++ ++ imx477->streaming = enable; ++ ++ /* vflip and hflip cannot change during streaming */ ++ __v4l2_ctrl_grab(imx477->vflip, enable); ++ __v4l2_ctrl_grab(imx477->hflip, enable); ++ ++ mutex_unlock(&imx477->mutex); ++ ++ return ret; ++ ++err_rpm_put: ++ pm_runtime_put(&client->dev); ++err_unlock: ++ mutex_unlock(&imx477->mutex); ++ ++ return ret; ++} ++ ++/* Power/clock management functions */ ++static int imx477_power_on(struct device *dev) ++{ ++ struct i2c_client *client = to_i2c_client(dev); ++ struct v4l2_subdev *sd = i2c_get_clientdata(client); ++ struct imx477 *imx477 = to_imx477(sd); ++ int ret; ++ ++ ret = regulator_bulk_enable(IMX477_NUM_SUPPLIES, ++ imx477->supplies); ++ if (ret) { ++ dev_err(&client->dev, "%s: failed to enable regulators\n", ++ __func__); ++ return ret; ++ } ++ ++ ret = clk_prepare_enable(imx477->xclk); ++ if (ret) { ++ dev_err(&client->dev, "%s: failed to enable clock\n", ++ __func__); ++ goto reg_off; ++ } ++ ++ gpiod_set_value_cansleep(imx477->reset_gpio, 1); ++ usleep_range(IMX477_XCLR_MIN_DELAY_US, ++ IMX477_XCLR_MIN_DELAY_US + IMX477_XCLR_DELAY_RANGE_US); ++ ++ return 0; ++ ++reg_off: ++ regulator_bulk_disable(IMX477_NUM_SUPPLIES, imx477->supplies); ++ return ret; ++} ++ ++static int imx477_power_off(struct device *dev) ++{ ++ struct i2c_client *client = to_i2c_client(dev); ++ struct v4l2_subdev *sd = i2c_get_clientdata(client); ++ struct imx477 *imx477 = to_imx477(sd); ++ ++ gpiod_set_value_cansleep(imx477->reset_gpio, 0); ++ regulator_bulk_disable(IMX477_NUM_SUPPLIES, imx477->supplies); ++ clk_disable_unprepare(imx477->xclk); ++ ++ /* Force reprogramming of the common registers when powered up again. */ ++ imx477->common_regs_written = false; ++ ++ return 0; ++} ++ ++static int __maybe_unused imx477_suspend(struct device *dev) ++{ ++ struct i2c_client *client = to_i2c_client(dev); ++ struct v4l2_subdev *sd = i2c_get_clientdata(client); ++ struct imx477 *imx477 = to_imx477(sd); ++ ++ if (imx477->streaming) ++ imx477_stop_streaming(imx477); ++ ++ return 0; ++} ++ ++static int __maybe_unused imx477_resume(struct device *dev) ++{ ++ struct i2c_client *client = to_i2c_client(dev); ++ struct v4l2_subdev *sd = i2c_get_clientdata(client); ++ struct imx477 *imx477 = to_imx477(sd); ++ int ret; ++ ++ if (imx477->streaming) { ++ ret = imx477_start_streaming(imx477); ++ if (ret) ++ goto error; ++ } ++ ++ return 0; ++ ++error: ++ imx477_stop_streaming(imx477); ++ imx477->streaming = 0; ++ return ret; ++} ++ ++static int imx477_get_regulators(struct imx477 *imx477) ++{ ++ struct i2c_client *client = v4l2_get_subdevdata(&imx477->sd); ++ unsigned int i; ++ ++ for (i = 0; i < IMX477_NUM_SUPPLIES; i++) ++ imx477->supplies[i].supply = imx477_supply_name[i]; ++ ++ return devm_regulator_bulk_get(&client->dev, ++ IMX477_NUM_SUPPLIES, ++ imx477->supplies); ++} ++ ++/* Verify chip ID */ ++static int imx477_identify_module(struct imx477 *imx477) ++{ ++ struct i2c_client *client = v4l2_get_subdevdata(&imx477->sd); ++ int ret; ++ u32 val; ++ ++ ret = imx477_read_reg(imx477, IMX477_REG_CHIP_ID, ++ IMX477_REG_VALUE_16BIT, &val); ++ if (ret) { ++ dev_err(&client->dev, "failed to read chip id %x, with error %d\n", ++ IMX477_CHIP_ID, ret); ++ return ret; ++ } ++ ++ if (val != IMX477_CHIP_ID) { ++ dev_err(&client->dev, "chip id mismatch: %x!=%x\n", ++ IMX477_CHIP_ID, val); ++ ret = -EINVAL; ++ } ++ ++ return 0; ++} ++ ++static const struct v4l2_subdev_core_ops imx477_core_ops = { ++ .subscribe_event = v4l2_ctrl_subdev_subscribe_event, ++ .unsubscribe_event = v4l2_event_subdev_unsubscribe, ++}; ++ ++static const struct v4l2_subdev_video_ops imx477_video_ops = { ++ .s_stream = imx477_set_stream, ++}; ++ ++static const struct v4l2_subdev_pad_ops imx477_pad_ops = { ++ .enum_mbus_code = imx477_enum_mbus_code, ++ .get_fmt = imx477_get_pad_format, ++ .set_fmt = imx477_set_pad_format, ++ .get_selection = imx477_get_selection, ++ .enum_frame_size = imx477_enum_frame_size, ++}; ++ ++static const struct v4l2_subdev_ops imx477_subdev_ops = { ++ .core = &imx477_core_ops, ++ .video = &imx477_video_ops, ++ .pad = &imx477_pad_ops, ++}; ++ ++static const struct v4l2_subdev_internal_ops imx477_internal_ops = { ++ .open = imx477_open, ++}; ++ ++/* Initialize control handlers */ ++static int imx477_init_controls(struct imx477 *imx477) ++{ ++ struct v4l2_ctrl_handler *ctrl_hdlr; ++ struct i2c_client *client = v4l2_get_subdevdata(&imx477->sd); ++ unsigned int i; ++ int ret; ++ ++ ctrl_hdlr = &imx477->ctrl_handler; ++ ret = v4l2_ctrl_handler_init(ctrl_hdlr, 14); ++ if (ret) ++ return ret; ++ ++ mutex_init(&imx477->mutex); ++ ctrl_hdlr->lock = &imx477->mutex; ++ ++ /* By default, PIXEL_RATE is read only */ ++ imx477->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &imx477_ctrl_ops, ++ V4L2_CID_PIXEL_RATE, ++ IMX477_PIXEL_RATE, ++ IMX477_PIXEL_RATE, 1, ++ IMX477_PIXEL_RATE); ++ ++ /* ++ * Create the controls here, but mode specific limits are setup ++ * in the imx477_set_framing_limits() call below. ++ */ ++ imx477->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &imx477_ctrl_ops, ++ V4L2_CID_VBLANK, 0, 0xffff, 1, 0); ++ imx477->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &imx477_ctrl_ops, ++ V4L2_CID_HBLANK, 0, 0xffff, 1, 0); ++ ++ /* HBLANK is read-only for now, but does change with mode. */ ++ if (imx477->hblank) ++ imx477->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY; ++ ++ imx477->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &imx477_ctrl_ops, ++ V4L2_CID_EXPOSURE, ++ IMX477_EXPOSURE_MIN, ++ IMX477_EXPOSURE_MAX, ++ IMX477_EXPOSURE_STEP, ++ IMX477_EXPOSURE_DEFAULT); ++ ++ v4l2_ctrl_new_std(ctrl_hdlr, &imx477_ctrl_ops, V4L2_CID_ANALOGUE_GAIN, ++ IMX477_ANA_GAIN_MIN, IMX477_ANA_GAIN_MAX, ++ IMX477_ANA_GAIN_STEP, IMX477_ANA_GAIN_DEFAULT); ++ ++ v4l2_ctrl_new_std(ctrl_hdlr, &imx477_ctrl_ops, V4L2_CID_DIGITAL_GAIN, ++ IMX477_DGTL_GAIN_MIN, IMX477_DGTL_GAIN_MAX, ++ IMX477_DGTL_GAIN_STEP, IMX477_DGTL_GAIN_DEFAULT); ++ ++ imx477->hflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx477_ctrl_ops, ++ V4L2_CID_HFLIP, 0, 1, 1, 0); ++ if (imx477->hflip) ++ imx477->hflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT; ++ ++ imx477->vflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx477_ctrl_ops, ++ V4L2_CID_VFLIP, 0, 1, 1, 0); ++ if (imx477->vflip) ++ imx477->vflip->flags |= V4L2_CTRL_FLAG_MODIFY_LAYOUT; ++ ++ v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &imx477_ctrl_ops, ++ V4L2_CID_TEST_PATTERN, ++ ARRAY_SIZE(imx477_test_pattern_menu) - 1, ++ 0, 0, imx477_test_pattern_menu); ++ for (i = 0; i < 4; i++) { ++ /* ++ * The assumption is that ++ * V4L2_CID_TEST_PATTERN_GREENR == V4L2_CID_TEST_PATTERN_RED + 1 ++ * V4L2_CID_TEST_PATTERN_BLUE == V4L2_CID_TEST_PATTERN_RED + 2 ++ * V4L2_CID_TEST_PATTERN_GREENB == V4L2_CID_TEST_PATTERN_RED + 3 ++ */ ++ v4l2_ctrl_new_std(ctrl_hdlr, &imx477_ctrl_ops, ++ V4L2_CID_TEST_PATTERN_RED + i, ++ IMX477_TEST_PATTERN_COLOUR_MIN, ++ IMX477_TEST_PATTERN_COLOUR_MAX, ++ IMX477_TEST_PATTERN_COLOUR_STEP, ++ IMX477_TEST_PATTERN_COLOUR_MAX); ++ /* The "Solid color" pattern is white by default */ ++ } ++ ++ if (ctrl_hdlr->error) { ++ ret = ctrl_hdlr->error; ++ dev_err(&client->dev, "%s control init failed (%d)\n", ++ __func__, ret); ++ goto error; ++ } ++ ++ imx477->sd.ctrl_handler = ctrl_hdlr; ++ ++ /* Setup exposure and frame/line length limits. */ ++ imx477_set_framing_limits(imx477); ++ ++ return 0; ++ ++error: ++ v4l2_ctrl_handler_free(ctrl_hdlr); ++ mutex_destroy(&imx477->mutex); ++ ++ return ret; ++} ++ ++static void imx477_free_controls(struct imx477 *imx477) ++{ ++ v4l2_ctrl_handler_free(imx477->sd.ctrl_handler); ++ mutex_destroy(&imx477->mutex); ++} ++ ++static int imx477_check_hwcfg(struct device *dev) ++{ ++ struct fwnode_handle *endpoint; ++ struct v4l2_fwnode_endpoint ep_cfg = { ++ .bus_type = V4L2_MBUS_CSI2_DPHY ++ }; ++ int ret = -EINVAL; ++ ++ endpoint = fwnode_graph_get_next_endpoint(dev_fwnode(dev), NULL); ++ if (!endpoint) { ++ dev_err(dev, "endpoint node not found\n"); ++ return -EINVAL; ++ } ++ ++ if (v4l2_fwnode_endpoint_alloc_parse(endpoint, &ep_cfg)) { ++ dev_err(dev, "could not parse endpoint\n"); ++ goto error_out; ++ } ++ ++ /* Check the number of MIPI CSI2 data lanes */ ++ if (ep_cfg.bus.mipi_csi2.num_data_lanes != 2) { ++ dev_err(dev, "only 2 data lanes are currently supported\n"); ++ goto error_out; ++ } ++ ++ /* Check the link frequency set in device tree */ ++ if (!ep_cfg.nr_of_link_frequencies) { ++ dev_err(dev, "link-frequency property not found in DT\n"); ++ goto error_out; ++ } ++ ++ if (ep_cfg.nr_of_link_frequencies != 1 || ++ ep_cfg.link_frequencies[0] != IMX477_DEFAULT_LINK_FREQ) { ++ dev_err(dev, "Link frequency not supported: %lld\n", ++ ep_cfg.link_frequencies[0]); ++ goto error_out; ++ } ++ ++ ret = 0; ++ ++error_out: ++ v4l2_fwnode_endpoint_free(&ep_cfg); ++ fwnode_handle_put(endpoint); ++ ++ return ret; ++} ++ ++static int imx477_probe(struct i2c_client *client) ++{ ++ struct device *dev = &client->dev; ++ struct imx477 *imx477; ++ int ret; ++ ++ imx477 = devm_kzalloc(&client->dev, sizeof(*imx477), GFP_KERNEL); ++ if (!imx477) ++ return -ENOMEM; ++ ++ v4l2_i2c_subdev_init(&imx477->sd, client, &imx477_subdev_ops); ++ ++ /* Check the hardware configuration in device tree */ ++ if (imx477_check_hwcfg(dev)) ++ return -EINVAL; ++ ++ /* Get system clock (xclk) */ ++ imx477->xclk = devm_clk_get(dev, NULL); ++ if (IS_ERR(imx477->xclk)) { ++ dev_err(dev, "failed to get xclk\n"); ++ return PTR_ERR(imx477->xclk); ++ } ++ ++ imx477->xclk_freq = clk_get_rate(imx477->xclk); ++ if (imx477->xclk_freq != IMX477_XCLK_FREQ) { ++ dev_err(dev, "xclk frequency not supported: %d Hz\n", ++ imx477->xclk_freq); ++ return -EINVAL; ++ } ++ ++ ret = imx477_get_regulators(imx477); ++ if (ret) { ++ dev_err(dev, "failed to get regulators\n"); ++ return ret; ++ } ++ ++ /* Request optional enable pin */ ++ imx477->reset_gpio = devm_gpiod_get_optional(dev, "reset", ++ GPIOD_OUT_HIGH); ++ ++ /* ++ * The sensor must be powered for imx477_identify_module() ++ * to be able to read the CHIP_ID register ++ */ ++ ret = imx477_power_on(dev); ++ if (ret) ++ return ret; ++ ++ ret = imx477_identify_module(imx477); ++ if (ret) ++ goto error_power_off; ++ ++ /* Initialize default format */ ++ imx477_set_default_format(imx477); ++ ++ /* Enable runtime PM and turn off the device */ ++ pm_runtime_set_active(dev); ++ pm_runtime_enable(dev); ++ pm_runtime_idle(dev); ++ ++ /* This needs the pm runtime to be registered. */ ++ ret = imx477_init_controls(imx477); ++ if (ret) ++ goto error_power_off; ++ ++ /* Initialize subdev */ ++ imx477->sd.internal_ops = &imx477_internal_ops; ++ imx477->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE | ++ V4L2_SUBDEV_FL_HAS_EVENTS; ++ imx477->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR; ++ ++ /* Initialize source pads */ ++ imx477->pad[IMAGE_PAD].flags = MEDIA_PAD_FL_SOURCE; ++ imx477->pad[METADATA_PAD].flags = MEDIA_PAD_FL_SOURCE; ++ ++ ret = media_entity_pads_init(&imx477->sd.entity, NUM_PADS, imx477->pad); ++ if (ret) { ++ dev_err(dev, "failed to init entity pads: %d\n", ret); ++ goto error_handler_free; ++ } ++ ++ ret = v4l2_async_register_subdev_sensor_common(&imx477->sd); ++ if (ret < 0) { ++ dev_err(dev, "failed to register sensor sub-device: %d\n", ret); ++ goto error_media_entity; ++ } ++ ++ return 0; ++ ++error_media_entity: ++ media_entity_cleanup(&imx477->sd.entity); ++ ++error_handler_free: ++ imx477_free_controls(imx477); ++ ++error_power_off: ++ pm_runtime_disable(&client->dev); ++ pm_runtime_set_suspended(&client->dev); ++ imx477_power_off(&client->dev); ++ ++ return ret; ++} ++ ++static int imx477_remove(struct i2c_client *client) ++{ ++ struct v4l2_subdev *sd = i2c_get_clientdata(client); ++ struct imx477 *imx477 = to_imx477(sd); ++ ++ v4l2_async_unregister_subdev(sd); ++ media_entity_cleanup(&sd->entity); ++ imx477_free_controls(imx477); ++ ++ pm_runtime_disable(&client->dev); ++ if (!pm_runtime_status_suspended(&client->dev)) ++ imx477_power_off(&client->dev); ++ pm_runtime_set_suspended(&client->dev); ++ ++ return 0; ++} ++ ++static const struct of_device_id imx477_dt_ids[] = { ++ { .compatible = "sony,imx477" }, ++ { /* sentinel */ } ++}; ++MODULE_DEVICE_TABLE(of, imx477_dt_ids); ++ ++static const struct dev_pm_ops imx477_pm_ops = { ++ SET_SYSTEM_SLEEP_PM_OPS(imx477_suspend, imx477_resume) ++ SET_RUNTIME_PM_OPS(imx477_power_off, imx477_power_on, NULL) ++}; ++ ++static struct i2c_driver imx477_i2c_driver = { ++ .driver = { ++ .name = "imx477", ++ .of_match_table = imx477_dt_ids, ++ .pm = &imx477_pm_ops, ++ }, ++ .probe_new = imx477_probe, ++ .remove = imx477_remove, ++}; ++ ++module_i2c_driver(imx477_i2c_driver); ++ ++MODULE_AUTHOR("Naushir Patuck "); ++MODULE_DESCRIPTION("Sony IMX477 sensor driver"); ++MODULE_LICENSE("GPL v2"); diff --git a/target/linux/bcm27xx/patches-5.10/950-0324-media-i2c-imx477-Add-support-for-adaptive-frame-cont.patch b/target/linux/bcm27xx/patches-5.10/950-0324-media-i2c-imx477-Add-support-for-adaptive-frame-cont.patch new file mode 100644 index 0000000000..530ce647b4 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0324-media-i2c-imx477-Add-support-for-adaptive-frame-cont.patch @@ -0,0 +1,182 @@ +From bb77f5ad580f08b0b60579370ad176a23960364a Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Fri, 8 May 2020 09:41:17 +0100 +Subject: [PATCH] media: i2c: imx477: Add support for adaptive frame + control + +Use V4L2_CID_EXPOSURE_AUTO_PRIORITY to control if the driver should +automatically adjust the sensor frame length based on exposure time, +allowing variable frame rates and longer exposures. + +Signed-off-by: Naushir Patuck +--- + drivers/media/i2c/imx477.c | 113 +++++++++++++++++++++++++++++-------- + 1 file changed, 91 insertions(+), 22 deletions(-) + +--- a/drivers/media/i2c/imx477.c ++++ b/drivers/media/i2c/imx477.c +@@ -1082,6 +1082,8 @@ struct imx477 { + struct v4l2_ctrl *hflip; + struct v4l2_ctrl *vblank; + struct v4l2_ctrl *hblank; ++ /* This ctrl allows automatic variable framerate */ ++ struct v4l2_ctrl *exposure_auto; + + /* Current mode */ + const struct imx477_mode *mode; +@@ -1278,6 +1280,72 @@ static int imx477_open(struct v4l2_subde + return 0; + } + ++static int imx477_set_exposure(struct imx477 *imx477, unsigned int val) ++{ ++ int ret; ++ ++ ret = imx477_write_reg(imx477, IMX477_REG_EXPOSURE, ++ IMX477_REG_VALUE_16BIT, val); ++ ++ /* Setup the frame length in the case of auto framerate mode. */ ++ if (imx477->exposure_auto->val) { ++ unsigned int frame_length, frame_length_max, frame_length_min; ++ ++ frame_length_min = imx477->vblank->minimum + ++ imx477->mode->height; ++ frame_length_max = imx477->vblank->maximum + ++ imx477->mode->height; ++ frame_length = max(frame_length_min, ++ val + IMX477_EXPOSURE_OFFSET); ++ frame_length = min(frame_length_max, frame_length); ++ ret += imx477_write_reg(imx477, IMX477_REG_FRAME_LENGTH, ++ IMX477_REG_VALUE_16BIT, frame_length); ++ } ++ ++ return ret; ++} ++ ++static void imx477_adjust_exposure_range(struct imx477 *imx477, ++ struct v4l2_ctrl *ctrl) ++{ ++ int exposure_max, exposure_def; ++ ++ if (ctrl->id == V4L2_CID_VBLANK || !ctrl->val) { ++ /* ++ * Either VBLANK has been changed or auto framerate ++ * adjusting has been disabled. Honour the VBLANK limits ++ * when setting exposure. ++ */ ++ exposure_max = imx477->mode->height + imx477->vblank->val - ++ IMX477_EXPOSURE_OFFSET; ++ ++ if (ctrl->id == V4L2_CID_EXPOSURE_AUTO_PRIORITY) { ++ /* ++ * Allow VBLANK adjustments since the driver is not ++ * handling frame length control automatically. ++ */ ++ __v4l2_ctrl_grab(imx477->vblank, false); ++ } ++ } else { ++ /* ++ * Auto framerate adjusting has been enabled. VBLANK ++ * ctrl has been disabled and exposure can ramp up ++ * to the maximum allowable value. ++ */ ++ exposure_max = IMX477_EXPOSURE_MAX; ++ /* ++ * Do not allow VBLANK adjustments if the driver is ++ * handling it frame length control automatically. ++ */ ++ __v4l2_ctrl_grab(imx477->vblank, true); ++ } ++ ++ exposure_def = min(exposure_max, imx477->exposure->val); ++ __v4l2_ctrl_modify_range(imx477->exposure, imx477->exposure->minimum, ++ exposure_max, imx477->exposure->step, ++ exposure_def); ++} ++ + static int imx477_set_ctrl(struct v4l2_ctrl *ctrl) + { + struct imx477 *imx477 = +@@ -1285,17 +1353,13 @@ static int imx477_set_ctrl(struct v4l2_c + struct i2c_client *client = v4l2_get_subdevdata(&imx477->sd); + int ret = 0; + +- if (ctrl->id == V4L2_CID_VBLANK) { +- int exposure_max, exposure_def; +- +- /* Update max exposure while meeting expected vblanking */ +- exposure_max = imx477->mode->height + ctrl->val - +- IMX477_EXPOSURE_OFFSET; +- exposure_def = min(exposure_max, imx477->exposure->val); +- __v4l2_ctrl_modify_range(imx477->exposure, +- imx477->exposure->minimum, +- exposure_max, imx477->exposure->step, +- exposure_def); ++ if (ctrl->id == V4L2_CID_VBLANK || ++ ctrl->id == V4L2_CID_EXPOSURE_AUTO_PRIORITY) { ++ /* ++ * These controls may change the limits of usable exposure, ++ * so check and adjust if necessary. ++ */ ++ imx477_adjust_exposure_range(imx477, ctrl); + } + + /* +@@ -1311,8 +1375,14 @@ static int imx477_set_ctrl(struct v4l2_c + IMX477_REG_VALUE_16BIT, ctrl->val); + break; + case V4L2_CID_EXPOSURE: +- ret = imx477_write_reg(imx477, IMX477_REG_EXPOSURE, +- IMX477_REG_VALUE_16BIT, ctrl->val); ++ ret = imx477_set_exposure(imx477, ctrl->val); ++ break; ++ case V4L2_CID_EXPOSURE_AUTO_PRIORITY: ++ /* ++ * imx477_set_exposure() will recalculate the frame length ++ * to adjust the framerate to match the exposure. ++ */ ++ ret = imx477_set_exposure(imx477, imx477->exposure->val); + break; + case V4L2_CID_DIGITAL_GAIN: + ret = imx477_write_reg(imx477, IMX477_REG_DIGITAL_GAIN, +@@ -1510,9 +1580,8 @@ unsigned int imx477_get_frame_length(con + + static void imx477_set_framing_limits(struct imx477 *imx477) + { ++ unsigned int frm_length_min, frm_length_default, hblank; + const struct imx477_mode *mode = imx477->mode; +- unsigned int frm_length_min, frm_length_default; +- unsigned int exposure_max, exposure_def, hblank; + + frm_length_min = imx477_get_frame_length(mode, &mode->timeperframe_min); + frm_length_default = +@@ -1522,15 +1591,10 @@ static void imx477_set_framing_limits(st + __v4l2_ctrl_modify_range(imx477->vblank, frm_length_min - mode->height, + IMX477_FRAME_LENGTH_MAX - mode->height, + 1, frm_length_default - mode->height); ++ ++ /* Setting this will adjust the exposure limits as well. */ + __v4l2_ctrl_s_ctrl(imx477->vblank, frm_length_default - mode->height); + +- /* Update max exposure while meeting expected vblanking */ +- exposure_max = IMX477_FRAME_LENGTH_MAX - IMX477_EXPOSURE_OFFSET; +- exposure_def = frm_length_default - mode->height - +- IMX477_EXPOSURE_OFFSET; +- __v4l2_ctrl_modify_range(imx477->exposure, imx477->exposure->minimum, +- exposure_max, imx477->exposure->step, +- exposure_def); + /* + * Currently PPL is fixed to the mode specified value, so hblank + * depends on mode->width only, and is not changeable in any +@@ -1939,6 +2003,11 @@ static int imx477_init_controls(struct i + IMX477_DGTL_GAIN_MIN, IMX477_DGTL_GAIN_MAX, + IMX477_DGTL_GAIN_STEP, IMX477_DGTL_GAIN_DEFAULT); + ++ imx477->exposure_auto = ++ v4l2_ctrl_new_std(ctrl_hdlr, &imx477_ctrl_ops, ++ V4L2_CID_EXPOSURE_AUTO_PRIORITY, ++ 0, 1, 1, 0); ++ + imx477->hflip = v4l2_ctrl_new_std(ctrl_hdlr, &imx477_ctrl_ops, + V4L2_CID_HFLIP, 0, 1, 1, 0); + if (imx477->hflip) diff --git a/target/linux/bcm27xx/patches-5.10/950-0325-media-i2c-imx477-Return-correct-result-on-sensor-id-.patch b/target/linux/bcm27xx/patches-5.10/950-0325-media-i2c-imx477-Return-correct-result-on-sensor-id-.patch new file mode 100644 index 0000000000..5d2cd9bdb7 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0325-media-i2c-imx477-Return-correct-result-on-sensor-id-.patch @@ -0,0 +1,25 @@ +From 15f2ddb7175008d14b25b7ab2eb71b487a497327 Mon Sep 17 00:00:00 2001 +From: Naushir Patuck +Date: Tue, 19 May 2020 16:56:33 +0100 +Subject: [PATCH] media: i2c: imx477: Return correct result on sensor + id verification + +The test should return -EIO if the register read id does not match +the expected sensor id. + +Signed-off-by: Naushir Patuck +--- + drivers/media/i2c/imx477.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/media/i2c/imx477.c ++++ b/drivers/media/i2c/imx477.c +@@ -1919,7 +1919,7 @@ static int imx477_identify_module(struct + if (val != IMX477_CHIP_ID) { + dev_err(&client->dev, "chip id mismatch: %x!=%x\n", + IMX477_CHIP_ID, val); +- ret = -EINVAL; ++ return -EIO; + } + + return 0; diff --git a/target/linux/bcm27xx/patches-5.10/950-0326-media-i2c-imx477-Parse-and-register-properties.patch b/target/linux/bcm27xx/patches-5.10/950-0326-media-i2c-imx477-Parse-and-register-properties.patch new file mode 100644 index 0000000000..902c839a7d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0326-media-i2c-imx477-Parse-and-register-properties.patch @@ -0,0 +1,45 @@ +From 2a968d0a82efc2018f1831adbcbfa093f8032c87 Mon Sep 17 00:00:00 2001 +From: Laurent Pinchart +Date: Sat, 4 Jul 2020 01:45:08 +0300 +Subject: [PATCH] media: i2c: imx477: Parse and register properties + +Parse device properties and register controls for them using the V4L2 +fwnode properties helpers. + +Signed-off-by: Laurent Pinchart +--- + drivers/media/i2c/imx477.c | 12 +++++++++++- + 1 file changed, 11 insertions(+), 1 deletion(-) + +--- a/drivers/media/i2c/imx477.c ++++ b/drivers/media/i2c/imx477.c +@@ -1957,11 +1957,12 @@ static int imx477_init_controls(struct i + { + struct v4l2_ctrl_handler *ctrl_hdlr; + struct i2c_client *client = v4l2_get_subdevdata(&imx477->sd); ++ struct v4l2_fwnode_device_properties props; + unsigned int i; + int ret; + + ctrl_hdlr = &imx477->ctrl_handler; +- ret = v4l2_ctrl_handler_init(ctrl_hdlr, 14); ++ ret = v4l2_ctrl_handler_init(ctrl_hdlr, 16); + if (ret) + return ret; + +@@ -2045,6 +2046,15 @@ static int imx477_init_controls(struct i + goto error; + } + ++ ret = v4l2_fwnode_device_parse(&client->dev, &props); ++ if (ret) ++ goto error; ++ ++ ret = v4l2_ctrl_new_fwnode_properties(ctrl_hdlr, &imx477_ctrl_ops, ++ &props); ++ if (ret) ++ goto error; ++ + imx477->sd.ctrl_handler = ctrl_hdlr; + + /* Setup exposure and frame/line length limits. */ diff --git a/target/linux/bcm27xx/patches-5.10/950-0327-media-bcm2835-unicam-Always-service-interrupts.patch b/target/linux/bcm27xx/patches-5.10/950-0327-media-bcm2835-unicam-Always-service-interrupts.patch new file mode 100644 index 0000000000..24c4b556f8 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0327-media-bcm2835-unicam-Always-service-interrupts.patch @@ -0,0 +1,51 @@ +From 3b1b2e000ea9430f6ccf588cb920bd8615701e1d Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Wed, 13 May 2020 18:28:27 +0100 +Subject: [PATCH] media: bcm2835-unicam: Always service interrupts + +From when bringing up the driver, there was a check in the isr +to ignore interrupts (claiming them handled) should the driver +not be streaming. + +The VPU now will not register a camera driver if it finds a +CSI2 node enabled in device tree, therefore this flawed check is +redundant. + +https://github.com/raspberrypi/linux/issues/3602 + +Signed-off-by: Dave Stevenson +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 15 --------------- + 1 file changed, 15 deletions(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -782,12 +782,6 @@ static bool unicam_all_nodes_streaming(s + return ret; + } + +-static bool unicam_all_nodes_disabled(struct unicam_device *dev) +-{ +- return !dev->node[IMAGE_PAD].streaming && +- !dev->node[METADATA_PAD].streaming; +-} +- + static void unicam_queue_event_sof(struct unicam_device *unicam) + { + struct v4l2_event event = { +@@ -815,15 +809,6 @@ static irqreturn_t unicam_isr(int irq, v + u32 ista, sta; + u64 ts; + +- /* +- * Don't service interrupts if not streaming. +- * Avoids issues if the VPU should enable the +- * peripheral without the kernel knowing (that +- * shouldn't happen, but causes issues if it does). +- */ +- if (unicam_all_nodes_disabled(unicam)) +- return IRQ_NONE; +- + sta = reg_read(unicam, UNICAM_STA); + /* Write value back to clear the interrupts */ + reg_write(unicam, UNICAM_STA, sta); diff --git a/target/linux/bcm27xx/patches-5.10/950-0328-media-bcm2835-unicam-Fix-uninitialized-warning.patch b/target/linux/bcm27xx/patches-5.10/950-0328-media-bcm2835-unicam-Fix-uninitialized-warning.patch new file mode 100644 index 0000000000..5f8d013d5d --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0328-media-bcm2835-unicam-Fix-uninitialized-warning.patch @@ -0,0 +1,21 @@ +From 0524a77793eceb9d7c34d2833bdeec9f9cdb3825 Mon Sep 17 00:00:00 2001 +From: Jacko Dirks +Date: Tue, 5 May 2020 14:33:31 +0200 +Subject: [PATCH] media: bcm2835: unicam: Fix uninitialized warning + +Signed-off-by: Jacko Dirks +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -1004,7 +1004,7 @@ const struct unicam_fmt *get_first_suppo + struct v4l2_subdev_mbus_code_enum mbus_code; + const struct unicam_fmt *fmt = NULL; + unsigned int i; +- int ret; ++ int ret = 0; + + for (i = 0; ret != -EINVAL && ret != -ENOIOCTLCMD; ++i) { + memset(&mbus_code, 0, sizeof(mbus_code)); diff --git a/target/linux/bcm27xx/patches-5.10/950-0329-media-bcm2835-unicam-Fixup-review-comments-from-Hans.patch b/target/linux/bcm27xx/patches-5.10/950-0329-media-bcm2835-unicam-Fixup-review-comments-from-Hans.patch new file mode 100644 index 0000000000..54fb9019e5 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0329-media-bcm2835-unicam-Fixup-review-comments-from-Hans.patch @@ -0,0 +1,244 @@ +From a658f8a9151c5852d590c998c2b806581509afbb Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 23 Jun 2020 15:14:05 +0100 +Subject: [PATCH] media: bcm2835-unicam: Fixup review comments from + Hans. + +Updates the driver based on the upstream review comments from +Hans Verkuil at https://patchwork.linuxtv.org/patch/63531/ + +Signed-off-by: Dave Stevenson +--- + drivers/media/platform/bcm2835/Kconfig | 12 ++-- + .../media/platform/bcm2835/bcm2835-unicam.c | 70 ++++++++----------- + 2 files changed, 39 insertions(+), 43 deletions(-) + +--- a/drivers/media/platform/bcm2835/Kconfig ++++ b/drivers/media/platform/bcm2835/Kconfig +@@ -1,7 +1,7 @@ + # Broadcom VideoCore4 V4L2 camera support + + config VIDEO_BCM2835_UNICAM +- tristate "Broadcom BCM2835 Unicam video capture driver" ++ tristate "Broadcom BCM283x/BCM271x Unicam video capture driver" + depends on VIDEO_V4L2 + depends on ARCH_BCM2835 || COMPILE_TEST + select VIDEO_V4L2_SUBDEV_API +@@ -9,9 +9,13 @@ config VIDEO_BCM2835_UNICAM + select VIDEOBUF2_DMA_CONTIG + select V4L2_FWNODE + help +- Say Y here to enable support for the BCM2835 CSI-2 receiver. This is a +- V4L2 driver that controls the CSI-2 receiver directly, independently +- from the VC4 firmware. ++ Say Y here to enable support for the BCM283x/BCM271x CSI-2 receiver. ++ This is a V4L2 driver that controls the CSI-2 receiver directly, ++ independently from the VC4 firmware. ++ This driver is mutually exclusive with the use of bcm2835-camera. The ++ firmware will disable all access to the peripheral from within the ++ firmware if it finds a DT node using it, and bcm2835-camera will ++ therefore fail to probe. + + To compile this driver as a module, choose M here. The module will be + called bcm2835-unicam. +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -1,6 +1,6 @@ + // SPDX-License-Identifier: GPL-2.0-only + /* +- * BCM2835 Unicam Capture Driver ++ * BCM283x / BCM271x Unicam Capture Driver + * + * Copyright (C) 2017-2020 - Raspberry Pi (Trading) Ltd. + * +@@ -571,9 +571,8 @@ static const struct unicam_fmt *find_for + return NULL; + } + +-static inline unsigned int bytes_per_line(u32 width, +- const struct unicam_fmt *fmt, +- u32 v4l2_fourcc) ++static unsigned int bytes_per_line(u32 width, const struct unicam_fmt *fmt, ++ u32 v4l2_fourcc) + { + if (v4l2_fourcc == fmt->repacked_fourcc) + /* Repacking always goes to 16bpp */ +@@ -718,7 +717,7 @@ static void unicam_wr_dma_addr(struct un + } + } + +-static inline unsigned int unicam_get_lines_done(struct unicam_device *dev) ++static unsigned int unicam_get_lines_done(struct unicam_device *dev) + { + dma_addr_t start_addr, cur_addr; + unsigned int stride = dev->node[IMAGE_PAD].v_fmt.fmt.pix.bytesperline; +@@ -732,7 +731,7 @@ static inline unsigned int unicam_get_li + return (unsigned int)(cur_addr - start_addr) / stride; + } + +-static inline void unicam_schedule_next_buffer(struct unicam_node *node) ++static void unicam_schedule_next_buffer(struct unicam_node *node) + { + struct unicam_device *dev = node->dev; + struct unicam_buffer *buf; +@@ -751,7 +750,7 @@ static inline void unicam_schedule_next_ + unicam_wr_dma_addr(dev, addr, size, node->pad_id); + } + +-static inline void unicam_schedule_dummy_buffer(struct unicam_node *node) ++static void unicam_schedule_dummy_buffer(struct unicam_node *node) + { + struct unicam_device *dev = node->dev; + +@@ -763,8 +762,8 @@ static inline void unicam_schedule_dummy + node->next_frm = NULL; + } + +-static inline void unicam_process_buffer_complete(struct unicam_node *node, +- unsigned int sequence) ++static void unicam_process_buffer_complete(struct unicam_node *node, ++ unsigned int sequence) + { + node->cur_frm->vb.field = node->m_fmt.field; + node->cur_frm->vb.sequence = sequence; +@@ -772,16 +771,6 @@ static inline void unicam_process_buffer + vb2_buffer_done(&node->cur_frm->vb.vb2_buf, VB2_BUF_STATE_DONE); + } + +-static bool unicam_all_nodes_streaming(struct unicam_device *dev) +-{ +- bool ret; +- +- ret = dev->node[IMAGE_PAD].open && dev->node[IMAGE_PAD].streaming; +- ret &= !dev->node[METADATA_PAD].open || +- dev->node[METADATA_PAD].streaming; +- return ret; +-} +- + static void unicam_queue_event_sof(struct unicam_device *unicam) + { + struct v4l2_event event = { +@@ -904,8 +893,8 @@ static int unicam_querycap(struct file * + struct unicam_node *node = video_drvdata(file); + struct unicam_device *dev = node->dev; + +- strlcpy(cap->driver, UNICAM_MODULE_NAME, sizeof(cap->driver)); +- strlcpy(cap->card, UNICAM_MODULE_NAME, sizeof(cap->card)); ++ strscpy(cap->driver, UNICAM_MODULE_NAME, sizeof(cap->driver)); ++ strscpy(cap->card, UNICAM_MODULE_NAME, sizeof(cap->card)); + + snprintf(cap->bus_info, sizeof(cap->bus_info), + "platform:%s", dev_name(&dev->pdev->dev)); +@@ -998,8 +987,8 @@ static int unicam_g_fmt_vid_cap(struct f + return 0; + } + +-static +-const struct unicam_fmt *get_first_supported_format(struct unicam_device *dev) ++static const struct unicam_fmt * ++get_first_supported_format(struct unicam_device *dev) + { + struct v4l2_subdev_mbus_code_enum mbus_code; + const struct unicam_fmt *fmt = NULL; +@@ -1589,7 +1578,8 @@ static void unicam_disable(struct unicam + clk_write(dev, 0); + } + +-static void unicam_return_buffers(struct unicam_node *node) ++static void unicam_return_buffers(struct unicam_node *node, ++ enum vb2_buffer_state state) + { + struct unicam_buffer *buf, *tmp; + unsigned long flags; +@@ -1597,15 +1587,15 @@ static void unicam_return_buffers(struct + spin_lock_irqsave(&node->dma_queue_lock, flags); + list_for_each_entry_safe(buf, tmp, &node->dma_queue, list) { + list_del(&buf->list); +- vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); ++ vb2_buffer_done(&buf->vb.vb2_buf, state); + } + + if (node->cur_frm) + vb2_buffer_done(&node->cur_frm->vb.vb2_buf, +- VB2_BUF_STATE_ERROR); ++ state); + if (node->next_frm && node->cur_frm != node->next_frm) + vb2_buffer_done(&node->next_frm->vb.vb2_buf, +- VB2_BUF_STATE_ERROR); ++ state); + + node->cur_frm = NULL; + node->next_frm = NULL; +@@ -1622,7 +1612,13 @@ static int unicam_start_streaming(struct + int ret; + + node->streaming = true; +- if (!unicam_all_nodes_streaming(dev)) { ++ if (!(dev->node[IMAGE_PAD].open && dev->node[IMAGE_PAD].streaming && ++ (!dev->node[METADATA_PAD].open || ++ dev->node[METADATA_PAD].streaming))) { ++ /* ++ * Metadata pad must be enabled before image pad if it is ++ * wanted. ++ */ + unicam_dbg(3, dev, "Not all nodes are streaming yet."); + return 0; + } +@@ -1726,7 +1722,7 @@ err_vpu_clock: + err_pm_put: + unicam_runtime_put(dev); + err_streaming: +- unicam_return_buffers(node); ++ unicam_return_buffers(node, VB2_BUF_STATE_QUEUED); + node->streaming = false; + + return ret; +@@ -1771,7 +1767,7 @@ static void unicam_stop_streaming(struct + } + + /* Clear all queued buffers for the node */ +- unicam_return_buffers(node); ++ unicam_return_buffers(node, VB2_BUF_STATE_ERROR); + } + + static int unicam_enum_input(struct file *file, void *priv, +@@ -1789,14 +1785,13 @@ static int unicam_enum_input(struct file + inp->std = 0; + } else if (v4l2_subdev_has_op(dev->sensor, video, s_std)) { + inp->capabilities = V4L2_IN_CAP_STD; +- if (v4l2_subdev_call(dev->sensor, video, g_tvnorms, &inp->std) +- < 0) ++ if (v4l2_subdev_call(dev->sensor, video, g_tvnorms, &inp->std) < 0) + inp->std = V4L2_STD_ALL; + } else { + inp->capabilities = 0; + inp->std = 0; + } +- sprintf(inp->name, "Camera 0"); ++ snprintf(inp->name, sizeof(inp->name), "Camera 0"); + return 0; + } + +@@ -2025,6 +2020,9 @@ static int unicam_s_dv_timings(struct fi + ret = v4l2_subdev_call(dev->sensor, video, g_dv_timings, + ¤t_timings); + ++ if (ret < 0) ++ return ret; ++ + if (v4l2_match_dv_timings(timings, ¤t_timings, 0, false)) + return 0; + +@@ -2455,12 +2453,6 @@ static int register_node(struct unicam_d + unicam_err(unicam, "Unable to allocate dummy buffer.\n"); + return -ENOMEM; + } +- +- if (pad_id == METADATA_PAD) { +- v4l2_disable_ioctl(vdev, VIDIOC_DQEVENT); +- v4l2_disable_ioctl(vdev, VIDIOC_SUBSCRIBE_EVENT); +- v4l2_disable_ioctl(vdev, VIDIOC_UNSUBSCRIBE_EVENT); +- } + if (pad_id == METADATA_PAD || + !v4l2_subdev_has_op(unicam->sensor, video, s_std)) { + v4l2_disable_ioctl(&node->video_dev, VIDIOC_S_STD); diff --git a/target/linux/bcm27xx/patches-5.10/950-0330-media-bcm2835-unicam-Retain-packing-information-on-G.patch b/target/linux/bcm27xx/patches-5.10/950-0330-media-bcm2835-unicam-Retain-packing-information-on-G.patch new file mode 100644 index 0000000000..eebc893f90 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0330-media-bcm2835-unicam-Retain-packing-information-on-G.patch @@ -0,0 +1,48 @@ +From bbdb89fbe61de5bacbb44ab919548fb84f1426d2 Mon Sep 17 00:00:00 2001 +From: Dave Stevenson +Date: Tue, 19 May 2020 11:46:47 +0100 +Subject: [PATCH] media: bcm2835-unicam: Retain packing information on + G_FMT + +The change to retrieve the pixel format always on g_fmt didn't +check whether the native or unpacked version of the format +had been requested, and always returned the packed one. +Correct this so that the packing setting is retained whereever +possible. + +Fixes "9d59e89 media: bcm2835-unicam: Re-fetch mbus code from subdev +on a g_fmt call" + +Signed-off-by: Dave Stevenson +--- + .../media/platform/bcm2835/bcm2835-unicam.c | 19 +++++++++++++++++-- + 1 file changed, 17 insertions(+), 2 deletions(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -980,8 +980,23 @@ static int unicam_g_fmt_vid_cap(struct f + if (!fmt) + return -EINVAL; + +- node->fmt = fmt; +- node->v_fmt.fmt.pix.pixelformat = fmt->fourcc; ++ if (node->fmt != fmt) { ++ /* ++ * The sensor format has changed so the pixelformat needs to ++ * be updated. Try and retain the packed/unpacked choice if ++ * at all possible. ++ */ ++ if (node->fmt->repacked_fourcc == ++ node->v_fmt.fmt.pix.pixelformat) ++ /* Using the repacked format */ ++ node->v_fmt.fmt.pix.pixelformat = fmt->repacked_fourcc; ++ else ++ /* Using the native format */ ++ node->v_fmt.fmt.pix.pixelformat = fmt->fourcc; ++ ++ node->fmt = fmt; ++ } ++ + *f = node->v_fmt; + + return 0; diff --git a/target/linux/bcm27xx/patches-5.10/950-0331-media-bcm2835-unicam-change-minimum-number-of-vb2_qu.patch b/target/linux/bcm27xx/patches-5.10/950-0331-media-bcm2835-unicam-change-minimum-number-of-vb2_qu.patch new file mode 100644 index 0000000000..052545e47e --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0331-media-bcm2835-unicam-change-minimum-number-of-vb2_qu.patch @@ -0,0 +1,28 @@ +From a450dcfff0fb6882228bef9242a0c1afcef6337a Mon Sep 17 00:00:00 2001 +From: David Plowman +Date: Thu, 28 May 2020 11:09:48 +0100 +Subject: [PATCH] media: bcm2835-unicam: change minimum number of + vb2_queue buffers to 1 + +Since the unicam driver was modified to write to a dummy buffer when no +user-supplied buffer is available, it can now write to and return a +buffer even when there's only a single one. Enable this by changing the +min_buffers_needed in the vb2_queue; it will be useful for enabling +still captures without allocating more memory than absolutely necessary. + +Signed-off-by: David Plowman +--- + drivers/media/platform/bcm2835/bcm2835-unicam.c | 2 +- + 1 file changed, 1 insertion(+), 1 deletion(-) + +--- a/drivers/media/platform/bcm2835/bcm2835-unicam.c ++++ b/drivers/media/platform/bcm2835/bcm2835-unicam.c +@@ -2428,7 +2428,7 @@ static int register_node(struct unicam_d + q->buf_struct_size = sizeof(struct unicam_buffer); + q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC; + q->lock = &node->lock; +- q->min_buffers_needed = 2; ++ q->min_buffers_needed = 1; + q->dev = &unicam->pdev->dev; + + ret = vb2_queue_init(q); diff --git a/target/linux/bcm27xx/patches-5.10/950-0332-staging-fbtft-Add-support-for-display-variants.patch b/target/linux/bcm27xx/patches-5.10/950-0332-staging-fbtft-Add-support-for-display-variants.patch new file mode 100644 index 0000000000..72f741fa89 --- /dev/null +++ b/target/linux/bcm27xx/patches-5.10/950-0332-staging-fbtft-Add-support-for-display-variants.patch @@ -0,0 +1,205 @@ +From 809abb2cd0f810ee0a94add2e5a038c78825915d Mon Sep 17 00:00:00 2001 +From: Phil Elwell +Date: Tue, 1 Sep 2020 18:15:27 +0100 +Subject: [PATCH] staging/fbtft: Add support for display variants + +Display variants are intended as a replacement for the now-deleted +fbtft_device drivers. Drivers can register additional compatible +strings with a custom callback that can make the required changes +to the fbtft_display structure. + +Start the ball rolling by adding adafruit18, adafruit18_green and +sainsmart18 displays. + +Signed-off-by: Phil Elwell +--- + drivers/staging/fbtft/fb_st7735r.c | 38 +++++++++++++++++++++++++++++- + drivers/staging/fbtft/fbtft-core.c | 16 ++++++++++++- + drivers/staging/fbtft/fbtft.h | 28 +++++++++++++++++----- + 3 files changed, 74 insertions(+), 8 deletions(-) + +--- a/drivers/staging/fbtft/fb_st7735r.c ++++ b/drivers/staging/fbtft/fb_st7735r.c +@@ -16,6 +16,10 @@ + #define DEFAULT_GAMMA "0F 1A 0F 18 2F 28 20 22 1F 1B 23 37 00 07 02 10\n" \ + "0F 1B 0F 17 33 2C 29 2E 30 30 39 3F 00 07 03 10" + ++#define ADAFRUIT18_GAMMA \ ++ "02 1c 07 12 37 32 29 2d 29 25 2B 39 00 01 03 10\n" \ ++ "03 1d 07 06 2E 2C 29 2D 2E 2E 37 3F 00 00 02 10" ++ + static const s16 default_init_sequence[] = { + -1, MIPI_DCS_SOFT_RESET, + -2, 150, /* delay */ +@@ -94,6 +98,14 @@ static void set_addr_win(struct fbtft_pa + write_reg(par, MIPI_DCS_WRITE_MEMORY_START); + } + ++static void adafruit18_green_tab_set_addr_win(struct fbtft_par *par, ++ int xs, int ys, int xe, int ye) ++{ ++ write_reg(par, 0x2A, 0, xs + 2, 0, xe + 2); ++ write_reg(par, 0x2B, 0, ys + 1, 0, ye + 1); ++ write_reg(par, 0x2C); ++} ++ + #define MY BIT(7) + #define MX BIT(6) + #define MV BIT(5) +@@ -174,12 +186,36 @@ static struct fbtft_display display = { + }, + }; + +-FBTFT_REGISTER_DRIVER(DRVNAME, "sitronix,st7735r", &display); ++int variant_adafruit18(struct fbtft_display *display) ++{ ++ display->gamma = ADAFRUIT18_GAMMA; ++ return 0; ++} ++ ++int variant_adafruit18_green(struct fbtft_display *display) ++{ ++ display->gamma = ADAFRUIT18_GAMMA; ++ display->fbtftops.set_addr_win = adafruit18_green_tab_set_addr_win; ++ return 0; ++} ++ ++FBTFT_REGISTER_DRIVER_START(&display) ++FBTFT_COMPATIBLE("sitronix,st7735r") ++FBTFT_COMPATIBLE("fbtft,sainsmart18") ++FBTFT_VARIANT_COMPATIBLE("fbtft,adafruit18", variant_adafruit18) ++FBTFT_VARIANT_COMPATIBLE("fbtft,adafruit18_green", variant_adafruit18_green) ++FBTFT_REGISTER_DRIVER_END(DRVNAME, &display); + + MODULE_ALIAS("spi:" DRVNAME); + MODULE_ALIAS("platform:" DRVNAME); + MODULE_ALIAS("spi:st7735r"); + MODULE_ALIAS("platform:st7735r"); ++MODULE_ALIAS("spi:sainsmart18"); ++MODULE_ALIAS("platform:sainsmart"); ++MODULE_ALIAS("spi:adafruit18"); ++MODULE_ALIAS("platform:adafruit18"); ++MODULE_ALIAS("spi:adafruit18_green"); ++MODULE_ALIAS("platform:adafruit18_green"); + + MODULE_DESCRIPTION("FB driver for the ST7735R LCD Controller"); + MODULE_AUTHOR("Noralf Tronnes"); +--- a/drivers/staging/fbtft/fbtft-core.c ++++ b/drivers/staging/fbtft/fbtft-core.c +@@ -24,6 +24,8 @@ + #include + #include + #include ++#include ++#include + + #include