move old kamikaze out of trunk - will put buildroot-ng in there as soon as all the...

[openwrt/staging/dedeckeh.git] / openwrt / target / linux / au1000-2.6 / patches / 008-isdel_cardbus.patch

diff --git a/openwrt/target/linux/au1000-2.6/patches/008-isdel_cardbus.patch b/openwrt/target/linux/au1000-2.6/patches/008-isdel_cardbus.patch
deleted file mode 100644 (file)
index 9e54ac1..0000000
--- a/openwrt/target/linux/au1000-2.6/patches/008-isdel_cardbus.patch
+++ /dev/null
@@ -1,63 +0,0 @@
-diff -urN linux-2.6.16.7/arch/mips/au1000/mtx-1/board_setup.c linux-2.6.16.7.new/arch/mips/au1000/mtx-1/board_setup.c
---- linux-2.6.16.7/arch/mips/au1000/mtx-1/board_setup.c        2006-04-23 14:39:21.000000000 +0200
-+++ linux-2.6.16.7.new/arch/mips/au1000/mtx-1/board_setup.c    2006-04-23 14:39:03.000000000 +0200
-@@ -44,6 +44,9 @@
- #include <asm/pgtable.h>
- #include <asm/mach-au1x00/au1000.h>
- 
-+extern int (*board_pci_idsel)(unsigned int devsel, int assert);
-+int    mtx1_pci_idsel(unsigned int devsel, int assert);
-+
- void board_reset (void)
- {
-       /* Hit BCSR.SYSTEM_CONTROL[SW_RST] */
-@@ -77,11 +80,37 @@
-       au_writel( 0xFFFFFFFF, SYS_TRIOUTCLR );
-       au_writel( 0x00000001, SYS_OUTPUTCLR ); // set M66EN (PCI 66MHz) to OFF
-       au_writel( 0x00000008, SYS_OUTPUTSET ); // set PCI CLKRUN# to OFF
-+      au_writel( 0x00000002, SYS_OUTPUTSET ); // set EXT_IO3 ON
-       au_writel( 0x00000020, SYS_OUTPUTCLR ); // set eth PHY TX_ER to OFF
- 
-       // enable LED and set it to green
-       au_writel( au_readl(GPIO2_DIR) | 0x1800, GPIO2_DIR );
-       au_writel( 0x18000800, GPIO2_OUTPUT );
- 
-+      board_pci_idsel = mtx1_pci_idsel;
-+
-       printk("4G Systems MTX-1 Board\n");
- }
-+
-+int
-+mtx1_pci_idsel(unsigned int devsel, int assert)
-+{
-+#define MTX_IDSEL_ONLY_0_AND_3 0
-+#if MTX_IDSEL_ONLY_0_AND_3
-+       if (devsel != 0 && devsel != 3) {
-+               printk("*** not 0 or 3\n");
-+               return 0;
-+       }
-+#endif
-+
-+       if (assert && devsel != 0) {
-+               // supress signal to cardbus
-+               au_writel( 0x00000002, SYS_OUTPUTCLR ); // set EXT_IO3 OFF
-+       }
-+       else {
-+               au_writel( 0x00000002, SYS_OUTPUTSET ); // set EXT_IO3 ON
-+       }
-+       au_sync_udelay(1);
-+       return 1;
-+}
-+
-diff -urN linux-2.6.16.7/arch/mips/au1000/mtx-1/irqmap.c linux-2.6.16.7.new/arch/mips/au1000/mtx-1/irqmap.c
---- linux-2.6.16.7/arch/mips/au1000/mtx-1/irqmap.c     2006-04-23 14:40:54.000000000 +0200
-+++ linux-2.6.16.7.new/arch/mips/au1000/mtx-1/irqmap.c 2006-04-23 14:40:12.000000000 +0200
-@@ -48,7 +48,7 @@
- #include <asm/mach-au1x00/au1000.h>
- 
- char irq_tab_alchemy[][5] __initdata = {
-- [0] = { -1, INTA, INTB, INTX, INTX},   /* IDSEL 00 - AdapterA-Slot0 (top)    */
-+ [0] = { -1, INTA, INTA, INTX, INTX},   /* IDSEL 00 - AdapterA-Slot0 (top)    */
-  [1] = { -1, INTB, INTA, INTX, INTX},   /* IDSEL 01 - AdapterA-Slot1 (bottom) */
-  [2] = { -1, INTC, INTD, INTX, INTX},   /* IDSEL 02 - AdapterB-Slot0 (top)    */
-  [3] = { -1, INTD, INTC, INTX, INTX},   /* IDSEL 03 - AdapterB-Slot1 (bottom) */