brcm2708: organize kernel patches

[openwrt/staging/dedeckeh.git] / target / linux / brcm2708 / patches-4.19 / 950-0707-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch

diff --git a/target/linux/brcm2708/patches-4.19/950-0707-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch b/target/linux/brcm2708/patches-4.19/950-0707-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch
new file mode 100644 (file)
index 0000000..30fa9b3
--- /dev/null
+++ b/target/linux/brcm2708/patches-4.19/950-0707-media-dt-bindings-Add-binding-for-the-Sony-IMX219-se.patch
@@ -0,0 +1,77 @@
+From 2d8a780a994098f7c532b712abd7298e0bca5a12 Mon Sep 17 00:00:00 2001
+From: Dave Stevenson <dave.stevenson@raspberrypi.org>
+Date: Wed, 28 Aug 2019 13:34:30 +0100
+Subject: [PATCH] media: dt-bindings: Add binding for the Sony IMX219
+ sensor
+
+The IMX219 is an 8MPix CSI2 sensor, supporting 2 or 4 data lanes.
+Document the binding for this device.
+
+Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
+---
+ .../devicetree/bindings/media/i2c/imx219.txt  | 59 +++++++++++++++++++
+ 1 file changed, 59 insertions(+)
+ create mode 100644 Documentation/devicetree/bindings/media/i2c/imx219.txt
+
+--- /dev/null
++++ b/Documentation/devicetree/bindings/media/i2c/imx219.txt
+@@ -0,0 +1,59 @@
++* Sony 1/4.0-Inch 8Mpixel CMOS Digital Image Sensor
++
++The Sony imx219 is a 1/4.0-inch CMOS active pixel digital image sensor with
++an active array size of 3280H x 2464V. It is programmable through I2C
++interface. The I2C address is fixed to 0x10 as per sensor data sheet.
++Image data is sent through MIPI CSI-2, which is configured as either 2 or 4
++data lanes.
++
++Required Properties:
++- compatible: value should be "sony,imx219" for imx219 sensor
++- reg: I2C bus address of the device
++- clocks: reference to the xclk input clock.
++- clock-names: should be "xclk".
++- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
++- AVDD-supply: Analog voltage supply, 2.8 volts
++- DVDD-supply: Digital core voltage supply, 1.2 volts
++
++Optional Properties:
++- xclr-gpios: reference to the GPIO connected to the xclr pin, if any. Must be
++            released after all supplies are applied.
++            This is an active high signal to the imx219.
++
++The imx219 device node should contain one 'port' child node with
++an 'endpoint' subnode. For further reading on port node refer to
++Documentation/devicetree/bindings/media/video-interfaces.txt.
++
++Endpoint node required properties for CSI-2 connection are:
++- remote-endpoint: a phandle to the bus receiver's endpoint node.
++- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
++- data-lanes: should be set to <1 2>, or  <1 2 3 4> (two or four lane CSI-2
++  supported)
++
++Example:
++      sensor@10 {
++              compatible = "sony,imx219";
++              reg = <0x10>;
++              #address-cells = <1>;
++              #size-cells = <0>;
++              clocks = <&imx219_clk>;
++              clock-names = "xclk";
++              xclr-gpios = <&gpio_sensor 0 0>;
++              DOVDD-supply = <&vgen4_reg>; /* 1.8v */
++              AVDD-supply = <&vgen3_reg>;  /* 2.8v */
++              DVDD-supply = <&vgen2_reg>;  /* 1.2v */
++
++              imx219_clk: camera-clk {
++                      compatible = "fixed-clock";
++                      #clock-cells = <0>;
++                      clock-frequency = <24000000>;
++              };
++
++              port {
++                      sensor_out: endpoint {
++                              remote-endpoint = <&csiss_in>;
++                              clock-lanes = <0>;
++                              data-lanes = <1 2>;
++                      };
++              };
++      };