brcm2708: update to latest patches from RPi foundation

[openwrt/staging/dedeckeh.git] / target / linux / brcm2708 / patches-4.19 / 950-0739-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch

diff --git a/target/linux/brcm2708/patches-4.19/950-0739-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch b/target/linux/brcm2708/patches-4.19/950-0739-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch
deleted file mode 100644 (file)
index 4291f9f..0000000
--- a/target/linux/brcm2708/patches-4.19/950-0739-dt-bindings-Add-binding-for-the-Infineon-IRS1125-sen.patch
+++ /dev/null
@@ -1,66 +0,0 @@
-From b4f8b92cdfd8ad2e04cdd3f0a73aa4e95d172fb1 Mon Sep 17 00:00:00 2001
-From: Markus Proeller <markus.proeller@pieye.org>
-Date: Thu, 10 Oct 2019 19:12:08 +0200
-Subject: [PATCH] dt-bindings: Add binding for the Infineon IRS1125
- sensor
-
-Adds a binding for the Infineon IRS1125 time-of-flight depth
-sensor.
-
-Signed-off-by: Markus Proeller <markus.proeller@pieye.org>
----
- .../devicetree/bindings/media/i2c/irs1125.txt | 48 +++++++++++++++++++
- 1 file changed, 48 insertions(+)
- create mode 100644 Documentation/devicetree/bindings/media/i2c/irs1125.txt
-
---- /dev/null
-+++ b/Documentation/devicetree/bindings/media/i2c/irs1125.txt
-@@ -0,0 +1,48 @@
-+* Infineon irs1125 time of flight sensor
-+
-+The Infineon irs1125 is a time of flight digital image sensor with
-+an active array size of 352H x 286V. It is programmable through I2C
-+interface. The I2C address defaults to 0x3D, but can be reconfigured
-+to address 0x3C or 0x41 via I2C commands. Image data is sent through
-+MIPI CSI-2, which is configured as either 1 or 2 data lanes.
-+
-+Required Properties:
-+- compatible: value should be "infineon,irs1125" for irs1125 sensor
-+- reg: I2C bus address of the device
-+- clocks: reference to the xclk input clock.
-+- pwdn-gpios: reference to the GPIO connected to the reset pin.
-+            This is an active low signal to the iirs1125.
-+
-+The irs1125 device node should contain one 'port' child node with
-+an 'endpoint' subnode. For further reading on port node refer to
-+Documentation/devicetree/bindings/media/video-interfaces.txt.
-+
-+Endpoint node required properties for CSI-2 connection are:
-+- remote-endpoint: a phandle to the bus receiver's endpoint node.
-+- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
-+- data-lanes: should be set to <1> or <1 2> (one or two lane CSI-2
-+  supported)
-+
-+Example:
-+      sensor@10 {
-+              compatible = "infineon,irs1125";
-+              reg = <0x3D>;
-+              #address-cells = <1>;
-+              #size-cells = <0>;
-+              clocks = <&irs1125_clk>;
-+              pwdn-gpios = <&gpio 5 0>;
-+
-+              irs1125_clk: camera-clk {
-+                      compatible = "fixed-clock";
-+                      #clock-cells = <0>;
-+                      clock-frequency = <26000000>;
-+              };
-+
-+              port {
-+                      sensor_out: endpoint {
-+                              remote-endpoint = <&csiss_in>;
-+                              clock-lanes = <0>;
-+                              data-lanes = <1 2>;
-+                      };
-+              };
-+      };