From e586de8dbf00fac72a37177ba08f74bb1091dd86 Mon Sep 17 00:00:00 2001 From: Daniel Golle Date: Thu, 10 Nov 2022 14:16:32 +0000 Subject: [PATCH] ath79: add support for Teltonika RUT300 Add support for the Teltonika RUT300 rugged industrial Ethernet router Hardware -------- SoC: Qualcomm Atheros QCA9531 RAM: 64M DDR2 (EtronTech EM68B16CWQK-25IH) FLASH: 16M SPI-NOR (Winbond W25Q128) ETH: 4x 100M LAN (QCA9533 internal AR8229 switch, eth0) 1x 100M WAN (QCA9533 internal PHY, eth1) UART: 115200 8n1, same debug port as other Teltonika devices USB: 1 single USB 2.0 host port BUTTON: Reset LED: 1x green power LED (always on) 5x yellow Ethernet port LED (controlled by Linux) WAN port LED is used as boot status and upgrade indicator as the power LED cannot be controlled in software. Use the *-factory.bin file to intially flash the device using the vendor firmware's Web-UI. Signed-off-by: Daniel Golle --- .../ath79/dts/qca9531_teltonika_rut300.dts | 164 ++++++++++++++++++ .../generic/base-files/etc/board.d/01_leds | 7 + .../generic/base-files/etc/board.d/02_network | 5 + target/linux/ath79/image/generic.mk | 47 +++++ 4 files changed, 223 insertions(+) create mode 100644 target/linux/ath79/dts/qca9531_teltonika_rut300.dts diff --git a/target/linux/ath79/dts/qca9531_teltonika_rut300.dts b/target/linux/ath79/dts/qca9531_teltonika_rut300.dts new file mode 100644 index 0000000000..a4f5fb543b --- /dev/null +++ b/target/linux/ath79/dts/qca9531_teltonika_rut300.dts @@ -0,0 +1,164 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include +#include "qca953x.dtsi" + +/ { + compatible = "teltonika,rut300", "teltonika,rut30x", "qca,qca9531"; + model = "TELTONIKA RUT300"; + + aliases { + label-mac-device = ð1; + led-boot = &led_wan; + led-failsafe = &led_wan; + led-running = &led_wan; + led-upgrade = &led_wan; + serial0 = &uart; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pmx_leds_switch>, <&jtag_disable_pins>; + + led_wan: wan { + label = "yellow:wan"; + gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + }; + + lan1 { + label = "yellow:lan1"; + gpios = <&gpio 4 GPIO_ACTIVE_HIGH>; + }; + + lan2 { + label = "yellow:lan2"; + gpios = <&gpio 3 GPIO_ACTIVE_HIGH>; + }; + + lan3 { + label = "yellow:lan3"; + gpios = <&gpio 2 GPIO_ACTIVE_HIGH>; + }; + + lan4 { + label = "yellow:lan4"; + gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&spi { + status = "okay"; + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x020000>; + read-only; + }; + + config: partition@20000 { + label = "config"; + reg = <0x020000 0x010000>; + read-only; + }; + + partition@30000 { + label = "art"; + reg = <0x030000 0x010000>; + read-only; + }; + + partition@40000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x040000 0xf30000>; + }; + + partition@f70000 { + label = "event-log"; + reg = <0xf70000 0x090000>; + }; + }; + }; +}; + +&usb0 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + hub_port0: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&uart { + status = "okay"; +}; + +&config { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_config_0: macaddr@0 { + reg = <0x0 0x6>; + }; +}; + +ð0 { + status = "okay"; + phy-handle = <&swphy0>; + + nvmem-cells = <&macaddr_config_0>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <1>; +}; + +ð1 { + phy-handle = <&swphy4>; + nvmem-cells = <&macaddr_config_0>; + nvmem-cell-names = "mac-address"; + + gmac-config { + device = <&gmac>; + switch-phy-swap = <1>; + }; +}; + +&pinmux { + pmx_leds_switch: leds_switch { + // switch port LEDs on GPIO 0~4 + pinctrl-single,bits = <0x0 0x00000000 0xffffffff>, + <0x4 0x00000000 0x000000ff>; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 606a194f7e..7fe9343876 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -337,6 +337,13 @@ teltonika,rut230-v1) ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth1" ucidef_set_led_switch "lan" "LAN" "green:lan" "switch0" "0x04" ;; +teltonika,rut300) + ucidef_set_led_netdev "wan" "WAN" "yellow:wan" "eth1" + ucidef_set_led_switch "lan1" "LAN1" "yellow:lan1" "switch0" "0x02" + ucidef_set_led_switch "lan2" "LAN2" "yellow:lan2" "switch0" "0x10" + ucidef_set_led_switch "lan3" "LAN3" "yellow:lan3" "switch0" "0x08" + ucidef_set_led_switch "lan4" "LAN4" "yellow:lan4" "switch0" "0x04" + ;; tplink,archer-a7-v5|\ tplink,archer-c7-v4|\ tplink,archer-c7-v5) diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index e47f66c2f2..339005f051 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -193,6 +193,11 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" ;; + teltonika,rut300) + ucidef_set_interface_wan "eth1" + ucidef_add_switch "switch0" \ + "0@eth0" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2" + ;; buffalo,wzr-hp-g300nh-rb|\ buffalo,wzr-hp-g300nh-s|\ dlink,dir-825-b1|\ diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 11c5669fe4..e5bc73e5a6 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -10,6 +10,7 @@ DEVICE_VARS += SEAMA_SIGNATURE SEAMA_MTDBLOCK DEVICE_VARS += KERNEL_INITRAMFS_PREFIX DAP_SIGNATURE DEVICE_VARS += EDIMAX_HEADER_MAGIC EDIMAX_HEADER_MODEL DEVICE_VARS += OPENMESH_CE_TYPE ZYXEL_MODEL_STRING +DEVICE_VARS += SUPPORTED_TELTONIKA_DEVICES define Build/addpattern -$(STAGING_DIR_HOST)/bin/addpattern -B $(ADDPATTERN_ID) \ @@ -139,6 +140,35 @@ define Build/teltonika-v1-header @mv $@.new $@ endef +metadata_json_teltonika = \ + '{ $(if $(IMAGE_METADATA),$(IMAGE_METADATA)$(comma)) \ + "metadata_version": "1.1", \ + "compat_version": "$(call json_quote,$(compat_version))", \ + "version":"$(call json_quote,$(VERSION_DIST))-$(call json_quote,$(VERSION_NUMBER))-$(call json_quote,$(REVISION))", \ + "device_code": [".*"], \ + "hwver": [".*"], \ + "batch": [".*"], \ + "serial": [".*"], \ + $(if $(DEVICE_COMPAT_MESSAGE),"compat_message": "$(call json_quote,$(DEVICE_COMPAT_MESSAGE))"$(comma)) \ + $(if $(filter-out 1.0,$(compat_version)),"new_supported_devices": \ + [$(call metadata_devices,$(SUPPORTED_TELTONIKA_DEVICES))]$(comma) \ + "supported_devices": ["$(call json_quote,$(legacy_supported_message))"]$(comma)) \ + $(if $(filter 1.0,$(compat_version)),"supported_devices":[$(call metadata_devices,$(SUPPORTED_TELTONIKA_DEVICES))]$(comma)) \ + "version_wrt": { \ + "dist": "$(call json_quote,$(VERSION_DIST))", \ + "version": "$(call json_quote,$(VERSION_NUMBER))", \ + "revision": "$(call json_quote,$(REVISION))", \ + "target": "$(call json_quote,$(TARGETID))", \ + "board": "$(call json_quote,$(if $(BOARD_NAME),$(BOARD_NAME),$(DEVICE_NAME)))" \ + }, \ + "hw_support": {}, \ + "hw_mods": {} \ + }' + +define Build/append-metadata-teltonika + echo $(call metadata_json_teltonika) | fwtool -I - $@ +endef + define Build/wrgg-pad-rootfs $(STAGING_DIR_HOST)/bin/padjffs2 $(IMAGE_ROOTFS) -c 64 >>$@ endef @@ -2527,6 +2557,23 @@ define Device/teltonika_rut230-v1 endef TARGET_DEVICES += teltonika_rut230-v1 +define Device/teltonika_rut300 + SOC := qca9531 + DEVICE_VENDOR := Teltonika + DEVICE_MODEL := RUT300 + SUPPORTED_TELTONIKA_DEVICES := teltonika,rut30x + DEVICE_PACKAGES := -kmod-ath9k -uboot-envtools -wpad-basic-wolfssl kmod-usb2 + IMAGE_SIZE := 15552k + IMAGES += factory.bin + IMAGE/factory.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | \ + append-rootfs | pad-rootfs | append-metadata-teltonika | \ + check-size $$$$(IMAGE_SIZE) + IMAGE/sysupgrade.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | \ + append-rootfs | pad-rootfs | append-metadata | \ + check-size $$$$(IMAGE_SIZE) +endef +TARGET_DEVICES += teltonika_rut300 + define Device/teltonika_rut955 SOC := ar9344 DEVICE_VENDOR := Teltonika -- 2.30.2