--- /dev/null
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/* High Level Configuration Options */
+#define CONFIG_ARM1136
+#define CONFIG_OX820
+
+#include <asm/arch/cpu.h> /* get chip and board defs */
+
+/* make cmd_ide.c quiet when compile */
+#define __io
+
+/*#define CONFIG_ARCH_CPU_INIT*/
+/*#define CONFIG_DISPLAY_CPUINFO*/
+/*#define CONFIG_DISPLAY_BOARDINFO*/
+/*#define CONFIG_BOARD_EARLY_INIT_F*/
+/*#define CONFIG_SKIP_LOWLEVEL_INIT*/
+
+/* mem */
+#define CONFIG_SYS_SDRAM_BASE 0x60000000
+#define CONFIG_NR_DRAM_BANKS 1
+#define CONFIG_MIN_SDRAM_SIZE (128 * 1024 * 1024) /* 128 MB */
+#define CONFIG_MAX_SDRAM_SIZE (512 * 1024 * 1024) /* 512 MB */
+#define CONFIG_SRAM_BASE 0x50000000
+#define CONFIG_SRAM_SIZE (64 * 1024)
+
+/* need do dma so better keep dcache off */
+#define CONFIG_SYS_DCACHE_OFF
+
+/* clock */
+#define CONFIG_PLLA_FREQ_MHZ 800
+#define CONFIG_RPSCLK 6250000
+#define CONFIG_SYS_HZ 1000
+#define CONFIG_SYS_CLK_FREQ CONFIG_RPSCLK
+#define CONFIG_SYS_TIMERBASE TIMER1_BASE
+#define CONFIG_TIMER_PRESCALE TIMER_PRESCALE_16
+
+/* serial */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_CLK CONFIG_RPSCLK
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_NS16550_COM1 UART_1_BASE
+#define CONFIG_CONS_INDEX 1
+
+/* ide */
+#define CONFIG_SYS_ATA_BASE_ADDR 0
+#define CONFIG_SYS_ATA_DATA_OFFSET 0
+#define CONFIG_SYS_ATA_REG_OFFSET 0
+#define CONFIG_SYS_ATA_ALT_OFFSET 0
+#define CONFIG_IDE_PLX
+#define CONFIG_SYS_IDE_MAXDEVICE 1
+#define CONFIG_SYS_IDE_MAXBUS 1
+#define CONFIG_IDE_PREINIT
+#define CONFIG_LBA48
+
+/* nand */
+#define CONFIG_NAND
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_NAND_BASE STATIC_CS0_BASE
+#define NAND_CLE_ADDR_PIN 19
+#define NAND_ALE_ADDR_PIN 18
+#define MTDPARTS_DEFAULT "mtdparts=41000000.nand:" \
+ "14m(boot)," \
+ "-(ubi)"
+#define MTDIDS_DEFAULT "nand0=41000000.nand"
+#define UBIPART_DEFAULT "ubi"
+
+/* net */
+#define CONFIG_DESIGNWARE_ETH
+#define CONFIG_DW_ALTDESCRIPTOR
+#define CONFIG_MII
+#define CONFIG_CMD_MII
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_REALTEK
+
+/* spl */
+#ifdef CONFIG_SPL_BUILD
+#define USE_DL_PREFIX /* rename malloc free etc, so we can override them */
+#endif
+
+#if defined(CONFIG_BOOT_FROM_NAND) || defined(CONFIG_BOOT_FROM_SATA)
+#define CONFIG_SPL
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_TEXT_BASE 0x50000000
+#define CONFIG_SPL_STACK (CONFIG_SRAM_BASE + (48 * 1024))
+#define CONFIG_SPL_DISPLAY_PRINT
+#define CONFIG_SPL_BSS_DRAM_START 0x65000000
+#define CONFIG_SPL_BSS_DRAM_SIZE 0x01000000
+#define CONFIG_SPL_MALLOC_START 0x66000000
+#endif
+
+#if defined(CONFIG_BOOT_FROM_NAND)
+#define CONFIG_SPL_NAND_SUPPORT
+#define BOOT_DEVICE_TYPE "NAND"
+#define BOOT_DEVICE_NAND 0xfeedbacc
+#define CONFIG_SPL_BOOT_DEVICE BOOT_DEVICE_NAND
+#define CONFIG_SPL_NAND_SIMPLE
+#define CONFIG_SPL_NAND_ECC
+#define CONFIG_SPL_NAND_SOFTECC
+#define CONFIG_SYS_NAND_ECCSIZE 512
+#define CONFIG_SYS_NAND_ECCBYTES 6
+#define CONFIG_SYS_NAND_ECCPOS {40, 41, 42, 43, 44, 45, 46, 47, \
+ 48, 49, 50, 51, 52, 53, 54, 55, \
+ 56, 57, 58, 59, 60, 61, 62, 63}
+#define CONFIG_SYS_NAND_PAGE_SIZE 2048
+#define CONFIG_SYS_NAND_OOBSIZE 64
+#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
+#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
+/* pages per erase block */
+#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE)
+/* nand spl use 1 erase block, and use bit to byte encode for reliability */
+#define CONFIG_SPL_MAX_SIZE (128 * 1024 / 8)
+#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x00040000
+/* spl kernel load is not enabled */
+#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x00200000
+#define CONFIG_CMD_SPL_NAND_OFS 0
+#define CONFIG_CMD_SPL_WRITE_SIZE 1024
+#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100)
+/* CONFIG_BOOT_FROM_NAND end */
+
+#elif defined(CONFIG_BOOT_FROM_SATA)
+#define CONFIG_SPL_BLOCK_SUPPORT
+#define BOOT_DEVICE_TYPE "SATA"
+#define BOOT_DEVICE_BLOCK 860202
+#define CONFIG_SPL_BOOT_DEVICE BOOT_DEVICE_BLOCK
+#define CONFIG_SPL_MAX_SIZE (36 * 1024)
+#define CONFIG_SPL_LIBDISK_SUPPORT
+#define CONFIG_SPL_BLOCKDEV_INTERFACE "ide"
+#define CONFIG_SPL_BLOCKDEV_ID 0
+
+#ifdef CONFIG_BOOT_FROM_FAT /* u-boot in fat partition */
+
+#define CONFIG_SPL_FAT_SUPPORT
+
+#define CONFIG_BLOCKDEV_FAT_BOOT_PARTITION 1 /* first partition */
+#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img" /* u-boot file name */
+/* enable U-Boot Falcon Mode */
+#define CONFIG_CMD_SPL
+#define CONFIG_SPL_OS_BOOT
+#define CONFIG_SPL_FAT_LOAD_ARGS_NAME "bootargs.bin" /* boot parameters */
+#define CONFIG_SPL_FAT_LOAD_KERNEL_NAME "falcon.img" /* kernel */
+#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100)
+
+#elif CONFIG_BOOT_FROM_EXT4
+
+#define CONFIG_SPL_EXT4_SUPPORT
+#define CONFIG_BLOCKDEV_EXT4_BOOT_PARTITION 1 /* first partition */
+#define CONFIG_SPL_EXT4_LOAD_PAYLOAD_NAME "/boot/u-boot.img" /* u-boot file name */
+/* enable U-Boot Falcon Mode */
+#define CONFIG_CMD_SPL
+#define CONFIG_SPL_OS_BOOT
+#define CONFIG_SPL_EXT4_LOAD_ARGS_NAME "/boot/bootargs.bin" /* boot parameters */
+#define CONFIG_SPL_EXT4_LOAD_KERNEL_NAME "/boot/falcon.img" /* kernel */
+#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100)
+
+#else /* u-boot in raw sectors */
+
+#define CONFIG_SYS_BLOCK_RAW_MODE_U_BOOT_SECTOR 1024
+/* spl kernel load is not enabled */
+#define CONFIG_SYS_BLOCK_RAW_MODE_KERNEL_SECTOR 4096
+#define CONFIG_SYS_BLOCK_RAW_MODE_ARGS_SECTOR 0
+#define CONFIG_SYS_BLOCK_RAW_MODE_ARGS_SECTORS (1024 / 512)
+#define CONFIG_SYS_SPL_ARGS_ADDR (CONFIG_SYS_SDRAM_BASE + 0x100)
+
+#endif /* CONFIG_BOOT_FROM_FAT */
+/* CONFIG_BOOT_FROM_SATA end */
+
+#else
+/* generic, no spl support */
+#endif
+
+/* boot */
+#define CONFIG_IDENT_STRING " for OXNAS"
+#define CONFIG_MACH_TYPE MACH_TYPE_OXNAS
+#ifndef CONFIG_SPL_BUILD
+/* Enable devicetree support */
+#define CONFIG_OF_LIBFDT
+#endif
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_INITRD_TAG
+#define CONFIG_BOOTDELAY 1
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+#define CONFIG_DEFAULT_CONSOLE_PARM "console=ttyS0,115200n8 earlyprintk=serial"
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+/* memtest works on */
+#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE)
+#define CONFIG_SYS_AUTOLOAD "no"
+
+#define CONFIG_DEFAULT_CONSOLE CONFIG_DEFAULT_CONSOLE_PARM "\0"
+#define CONFIG_BOOTARGS CONFIG_DEFAULT_CONSOLE_PARM
+#define CONFIG_BOOTCOMMAND "run nandboot"
+#define CONFIG_BOOT_RETRY_TIME -1
+#define CONFIG_RESET_TO_RETRY 60
+
+#define CONFIG_NETCONSOLE
+#define CONFIG_IPADDR 192.168.50.100
+#define CONFIG_SERVERIP 192.168.50.59
+
+/* A sane default configuration...
+ * When booting without a valid environment in ubi, first to loading and booting
+ * the kernel image directly above U-Boot, maybe both were loaded there by
+ * another bootloader.
+ * Also use that same offset (0x90000) to load the rescue image later on (by
+ * adding it onto the flash address where U-Boot is supposed to be stored by
+ * the legacy loader, 0x440000, resulting in offset 0x4d0000 on the flash).
+ * When coming up with a valid environment in ubi, first try to load the
+ * kernel from a ubi volume kernel, if that fails, fallback to the rescue
+ * image stored in boot partition. As a last resort try booting via
+ * DHCP/TFTP.
+ * In case there is no valid environment, first probe for a uimage in ram left
+ * behind by the first bootloader on a tftp boot.
+ * If that fails, switch to normal boot order and save environment.
+ * The loader is supposed to be written to flash at offset 0x440000 and loaded to
+ * RAM at 0x64000000
+ */
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "load_kernel_ubi=ubi readvol 0x62000000 kernel;\0" \
+ "load_kernel_rescue=nand read 0x62000000 0x4e0000 0x400000;\0" \
+ "load_kernel_dhcp=dhcp 0x62000000 oxnas-rescue.bin;\0" \
+ "boot_kernel=bootm 0x62000000;\0" \
+ "boot_ubi=run load_kernel_ubi && run boot_kernel;\0" \
+ "boot_rescue=run load_kernel_rescue && run boot_kernel;\0" \
+ "boot_dhcp=run load_kernel_dhcp && run boot_kernel;\0" \
+ "normalboot=run boot_ubi; run boot_rescue; run boot_dhcp;\0" \
+ "firstboot=bootm 0x640a0000; setenv bootcmd run normalboot; " \
+ "setenv firstboot; saveenv; run bootcmd; \0" \
+ "bootcmd=run firstboot; \0" \
+ "console=" CONFIG_DEFAULT_CONSOLE \
+ "bootargs=" CONFIG_BOOTARGS "\0" \
+ "mtdids=" MTDIDS_DEFAULT "\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
+
+/* env */
+#if defined(CONFIG_BOOT_FROM_NAND)
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET 0x000C0000
+#define CONFIG_ENV_SIZE 0x00020000
+#define CONFIG_ENV_OFFSET_REDUND 0x00100000
+#define CONFIG_ENV_SIZE_REDUND 0x00020000
+#define CONFIG_ENV_RANGE (CONFIG_ENV_SIZE * 2)
+/* CONFIG_BOOT_FROM_NAND end */
+
+#elif defined(CONFIG_BOOT_FROM_SATA)
+#ifdef CONFIG_BOOT_FROM_EXT4
+#define CONFIG_ENV_IS_IN_EXT4
+#define CONFIG_START_IDE
+#define EXT4_ENV_INTERFACE "ide"
+#define EXT4_ENV_DEVICE 0
+#define EXT4_ENV_PART 1
+#define EXT4_ENV_FILE "/boot/u-boot.env"
+#define CONFIG_ENV_SIZE (16 * 1024)
+#else
+#define CONFIG_ENV_IS_IN_FAT
+#define CONFIG_START_IDE
+#define FAT_ENV_INTERFACE "ide"
+#define FAT_ENV_DEVICE 0
+#define FAT_ENV_PART 1
+#define FAT_ENV_FILE "u-boot.env"
+#define CONFIG_ENV_SIZE (16 * 1024)
+#endif
+/* CONFIG_BOOT_FROM_SATA end */
+#elif defined(CONFIG_BOOT_FROM_SATA)
+
+#else
+/* generic */
+#define CONFIG_ENV_IS_IN_UBI 1
+#define CONFIG_ENV_UBI_PART UBIPART_DEFAULT
+#define CONFIG_ENV_UBI_VOLUME "ubootenv"
+#define CONFIG_ENV_UBI_VOLUME_REDUND "ubootenv2"
+#define CONFIG_ENV_SIZE (16 * 1024)
+#endif
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
+#define CONFIG_SYS_TEXT_BASE 0x64000000
+#define CONFIG_SYS_INIT_SP_ADDR 0x65000000
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (1 * 1024 * 1024)
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#define CONFIG_SYS_PROMPT "OX820 # "
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size*/
+#define CONFIG_SYS_PBSIZE 1024 /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_AUTO_COMPLETE
+
+/* usb */
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
+#define CONFIG_USB_EHCI
+#define CONFIG_EHCI_IS_TDI
+/* #define CONFIG_USB_EHCI_TXFIFO_THRESH 0x3F */
+#define CONFIG_USB_PLLB_CLK
+#define CONFIG_USB_EHCI_OXNAS
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_USB_STORAGE
+#endif
+#define CONFIG_CMD_USB
+
+/* cmds */
+#define CONFIG_SYS_NO_FLASH
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_ENV_FLAGS
+
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_PXE
+
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_FAT
+#define CONFIG_FAT_WRITE
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_EXT4
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_CMD_EXT4_WRITE
+#endif
+
+#define CONFIG_CMD_ZIP
+#define CONFIG_CMD_UNZIP
+#define CONFIG_CMD_TIME
+#define CONFIG_CMD_TERMINAL
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_MD5SUM
+#define CONFIG_CMD_HASH
+#define CONFIG_CMD_INI
+#define CONFIG_CMD_GETTIME
+#define CONFIG_CMD_BOOTMENU
+#define CONFIG_CMD_ELF
+
+#define CONFIG_DOS_PARTITION
+#define CONFIG_EFI_PARTITION
+
+/* for CONFIG_CMD_MTDPARTS */
+#define CONFIG_MTD_DEVICE
+/* for CONFIG_CMD_UBI */
+#define CONFIG_MTD_PARTITIONS
+/* for CONFIG_CMD_UBI */
+#define CONFIG_RBTREE
+
+/* optional, for CONFIG_CMD_BOOTM & required by CONFIG_CMD_UBIFS */
+#define CONFIG_LZO
+#define CONFIG_LZMA
+#define CONFIG_BZIP2
+
+/* for CONFIG_CMD_ZIP */
+#define CONFIG_GZIP_COMPRESSED
+/* for CONFIG_CMD_MD5SUM */
+#define CONFIG_MD5
+#define CONFIG_MD5SUM_VERIFY
+/* enable CONFIG_CMD_HASH's verification feature */
+#define CONFIG_HASH_VERIFY
+#define CONFIG_REGEX
+/* for CONFIG_CMD_BOOTMENU & CONFIG_CMD_PXE */
+#define CONFIG_MENU
+
+/* for new FIT uImage format generated in OpenWrt */
+#define CONFIG_FIT
+
+#endif /* __CONFIG_H */
projects / openwrt / staging / yousong.git / blobdiff