brcm2708: remove linux 4.4 support

[openwrt/staging/yousong.git] / target / linux / brcm2708 / patches-4.4 / 0203-pi3-miniuart-bt-overlay-Correct-and-clarify-info.patch

diff --git a/target/linux/brcm2708/patches-4.4/0203-pi3-miniuart-bt-overlay-Correct-and-clarify-info.patch b/target/linux/brcm2708/patches-4.4/0203-pi3-miniuart-bt-overlay-Correct-and-clarify-info.patch
deleted file mode 100644 (file)
index 70fada1..0000000
--- a/target/linux/brcm2708/patches-4.4/0203-pi3-miniuart-bt-overlay-Correct-and-clarify-info.patch
+++ /dev/null
@@ -1,41 +0,0 @@
-From 49da60a482e61465bb7a6148232bb5a2dd48919f Mon Sep 17 00:00:00 2001
-From: Phil Elwell <phil@raspberrypi.org>
-Date: Thu, 17 Mar 2016 10:16:16 +0000
-Subject: [PATCH] pi3-miniuart-bt-overlay: Correct and clarify info
-
-Signed-off-by: Phil Elwell <phil@raspberrypi.org>
----
- arch/arm/boot/dts/overlays/README                      | 6 ++++--
- arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts | 6 ++++--
- 2 files changed, 8 insertions(+), 4 deletions(-)
-
---- a/arch/arm/boot/dts/overlays/README
-+++ b/arch/arm/boot/dts/overlays/README
-@@ -511,8 +511,10 @@ Name:   pi3-miniuart-bt
- Info:   Switch Pi3 Bluetooth function to use the mini-UART (ttyS0) and restore
-         UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum
-         usable baudrate.
--        N.B. It is also necessary to edit /lib/systemd/system/hciuart.server
--        and replace ttyAMA0 with ttyS0.
-+        N.B. It is also necessary to edit /lib/systemd/system/hciuart.service
-+        and replace ttyAMA0 with ttyS0, unless you have a system with udev rules
-+        that create /dev/serial0 and /dev/serial1, in which case use
-+        /dev/serial1 instead because it will always be correct.
- Load:   dtoverlay=pi3-miniuart-bt
- Params: <None>
- 
---- a/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts
-+++ b/arch/arm/boot/dts/overlays/pi3-miniuart-bt-overlay.dts
-@@ -5,8 +5,10 @@
-    UART0/ttyAMA0 over GPIOs 14 & 15. Note that this may reduce the maximum
-    usable baudrate.
- 
--   It is also necessary to edit /lib/systemd/system/hciuart.server and
--   replace ttyAMA0 with ttyS0.
-+   It is also necessary to edit /lib/systemd/system/hciuart.service and
-+   replace ttyAMA0 with ttyS0, unless you have a system with udev rules
-+   that create /dev/serial0 and /dev/serial1, in which case use /dev/serial1
-+   instead because it will always be correct.
- 
-    If cmdline.txt uses the alias serial0 to refer to the user-accessable port
-    then the firmware will replace with the appropriate port whether or not