-diff -urN compat-wireless-2008-08-06/config.mk compat-wireless-2008-08-06.new/config.mk
---- compat-wireless-2008-08-06/config.mk 2008-07-18 06:11:03.000000000 +0200
-+++ compat-wireless-2008-08-06.new/config.mk 2008-08-20 17:30:13.000000000 +0200
-@@ -72,70 +72,6 @@
- CONFIG_ATH5K=m
- CONFIG_ATH5K_DEBUG=n
-
--# Required for older kernels which still use this flag.
--CONFIG_IWLWIFI=m
--
--CONFIG_IWLCORE=m
--CONFIG_IWL3945=m
--CONFIG_IWL4965=m
--CONFIG_IWL4965_HT=y
--CONFIG_B43=m
--# B43 uses PCMCIA only for Compact Flash. The Cardbus cards uses PCI
--# Example, bcm4318:
--# http://www.multicap.biz/wireless-lan/indoor-wlan-hardware/sdc-cf10g-80211g-compact-flash-module
--CONFIG_B43_PCMCIA=y
--CONFIG_B43_DMA=y
--CONFIG_B43_PIO=y
--# B43_PIO selects SSB_BLOCKIO
--CONFIG_SSB_BLOCKIO=y
--CONFIG_B43_DMA_AND_PIO_MODE=y
--CONFIG_B43_PCI_AUTOSELECT=y
--CONFIG_B43_PCICORE_AUTOSELECT=y
--#CONFIG_B43_RFKILL=n
--CONFIG_B43_LEDS=y
--# CONFIG_B43_DEBUG is not set
--
--CONFIG_B43LEGACY=m
--CONFIG_B43LEGACY_PCI_AUTOSELECT=y
--CONFIG_B43LEGACY_PCICORE_AUTOSELECT=y
--CONFIG_B43LEGACY_DMA=y
--CONFIG_B43LEGACY_PIO=y
--CONFIG_B43LEGACY_DMA_AND_PIO_MODE=y
--
--# The Intel ipws
--CONFIG_IPW2100=m
--CONFIG_IPW2100_MONITOR=y
--CONFIG_IPW2200=m
--CONFIG_IPW2200_MONITOR=y
--CONFIG_IPW2200_RADIOTAP=y
--CONFIG_IPW2200_PROMISCUOUS=y
--# The above enables use a second interface prefixed 'rtap'.
--# Example usage:
--#
--# % modprobe ipw2200 rtap_iface=1
--# % ifconfig rtap0 up
--# % tethereal -i rtap0
--#
--# If you do not specify 'rtap_iface=1' as a module parameter then
--# the rtap interface will not be created and you will need to turn
--# it on via sysfs:
--#
--# % echo 1 > /sys/bus/pci/drivers/ipw2200/*/rtap_iface
--CONFIG_IPW2200_QOS=y
--
--NEED_IEEE80211=y
--
--CONFIG_P54_PCI=m
--
--CONFIG_SSB_PCIHOST_POSSIBLE=y
--CONFIG_SSB_PCIHOST=y
--CONFIG_SSB_DRIVER_PCICORE_POSSIBLE=y
--CONFIG_SSB_DRIVER_PCICORE=y
--CONFIG_SSB_B43_PCI_BRIDGE=y
--
--CONFIG_RTL8180=m
--CONFIG_ADM8211=m
--
- CONFIG_RT2X00_LIB_PCI=m
- CONFIG_RT2400PCI=m
- CONFIG_RT2500PCI=m
-@@ -159,32 +95,6 @@
- ifneq ($(CONFIG_USB),)
- CONFIG_ZD1211RW=m
-
--# support for USB Wireless devices using Atmel at76c503,
--# at76c505 or at76c505a chips.
--CONFIG_USB_ATMEL=m
--
--# Stuff here things which depend on kernel versions for USB
--ifeq ($(shell test -e $(KLIB_BUILD)/Makefile && echo yes),yes)
--KERNEL_SUBLEVEL = $(shell $(MAKE) -C $(KLIB_BUILD) kernelversion | sed -n 's/^2\.6\.\([0-9]\+\).*/\1/p')
--ifeq ($(shell test $(KERNEL_SUBLEVEL) -gt 21 && echo yes),yes)
--
--# Sorry, rndis_wlan uses cancel_work_sync which is new and can't be done in compat...
--
--# Wireless RNDIS USB support (RTL8185 802.11g) A-Link WL54PC
--# All of these devices are based on Broadcom 4320 chip which
--# is only wireless RNDIS chip known to date.
--# Note: this depends on CONFIG_USB_NET_RNDIS_HOST and CONFIG_USB_NET_CDCETHER
--# it also requires new RNDIS_HOST and CDC_ETHER modules which we add
--CONFIG_USB_NET_RNDIS_HOST=m
--CONFIG_USB_NET_RNDIS_WLAN=m
--CONFIG_USB_NET_CDCETHER=m
--
--endif
--endif
--
--CONFIG_P54_USB=m
--CONFIG_RTL8187=m
--
- # RT2500USB does not require firmware
- CONFIG_RT2500USB=m
- CONFIG_RT2X00_LIB_USB=m
-@@ -209,39 +119,6 @@
- CONFIG_RT2X00_LIB_FIRMWARE=y
- endif
-
--# p54
--CONFIG_P54_COMMON=m
--
--# Sonics Silicon Backplane
--CONFIG_SSB_POSSIBLE=y
--CONFIG_SSB=m
--CONFIG_SSB_SPROM=y
--
--ifneq ($(CONFIG_PCMCIA),)
--CONFIG_SSB_PCMCIAHOST=y
--endif
--
--# These two are for mips
--CONFIG_SSB_DRIVER_MIPS=n
--CONFIG_SSB_PCICORE_HOSTMODE=n
--# CONFIG_SSB_DEBUG is not set
--# CONFIG_SSB_DRIVER_EXTIF=y
--
--ifneq ($(CONFIG_USB),)
--CONFIG_LIBERTAS_USB=m
--NEED_LIBERTAS=y
--endif
--ifneq ($(CONFIG_PCMCIA),)
--CONFIG_LIBERTAS_CS=m
--NEED_LIBERTAS=y
--endif
--ifeq ($(NEED_LIBERTAS),y)
--CONFIG_LIBERTAS=m
--# Libertas uses the old stack but not fully, it will soon
--# be cleaned.
--NEED_IEEE80211=y
--endif
--
- ifeq ($(NEED_IEEE80211),y)
- # Old ieee80211 "stack"
- # Note: old softmac is scheduled for removal so we
projects / openwrt / svn-archive / archive.git / blobdiff