disable image generation for boards which we still have problems with (at least if...

[openwrt/svn-archive/archive.git] / target / linux / adm5120-2.6 / image / lzma-loader / src / board.c

diff --git a/target/linux/adm5120-2.6/image/lzma-loader/src/board.c b/target/linux/adm5120-2.6/image/lzma-loader/src/board.c
index 616e7562a88b1f0b3f8a76a5ea6a88ecb84f3050..baffe04ef1b0ca514a4aa9476d66df866dd50d54 100644 (file)
--- a/target/linux/adm5120-2.6/image/lzma-loader/src/board.c
+++ b/target/linux/adm5120-2.6/image/lzma-loader/src/board.c
@@ -1,5 +1,5 @@
 /*
- * ADM5120 specific board support for LZMA decompressor 
+ * ADM5120 specific board support for LZMA decompressor
  *
  * Copyright (C) 2007 OpenWrt.org
  * Copyright (C) 2007 Gabor Juhos <juhosg@freemail.hu>
@@ -24,7 +24,7 @@
 #define READREG(r)     *(volatile unsigned int *)(r)
 #define WRITEREG(r,v)  *(volatile unsigned int *)(r) = v
 
-/* 
+/*
  * INTC definitions
  */
 #define INTC_BASE      0xB2200000
@@ -32,7 +32,7 @@
 /* INTC registers */
 #define INTC_REG_IRQ_DISABLE   0x0C
 
-/* 
+/*
  * UART definitions
  */
 #define UART_BASE      0xB2600000
@@ -61,7 +61,7 @@
 #define UART_FLAG_RXFF ( 1 << 6 )      /* RX FIFO full */
 #define UART_FLAG_TXFE ( 1 << 7 )      /* TX FIFO empty */
 
-/* 
+/*
  * SWITCH definitions
  */
 #define SWITCH_BASE    0xB2000000
@@ -96,8 +96,9 @@
 
 static void uart_init(void)
 {
+#if 0
        unsigned int t;
-       
+
        /* disable uart */
        UART_WRITE(UART_REG_CTRL, 0);
 
@@ -106,7 +107,7 @@ static void uart_init(void)
        UART_WRITE(UART_REG_LCRM, t);
        t = UART_READ(UART_REG_LCRL);
        UART_WRITE(UART_REG_LCRL, t);
-       
+
        /* keep data, stop, and parity bits, but disable FIFO */
        t = UART_READ(UART_REG_LCRH);
        t &= ~(UART_LCRH_FEN);
@@ -117,6 +118,7 @@ static void uart_init(void)
 
        /* enable uart, and disable interrupts */
        UART_WRITE(UART_REG_CTRL, UART_CTRL_EN);
+#endif
 }
 
 static void uart_putc(int ch)
@@ -125,7 +127,7 @@ static void uart_putc(int ch)
 
        UART_WRITE(UART_REG_DATA, ch);
 
-       while ((UART_READ(UART_REG_FLAG) & UART_FLAG_TXFF) != 0);
+       while ((UART_READ(UART_REG_FLAG) & UART_FLAG_TXFE) == 0);
 }
 
 /*
@@ -150,7 +152,7 @@ static void intc_init(void)
 static void switch_init(void)
 {
        /* disable PHYS ports */
-       SWITCH_WRITE(SWITCH_REG_PORT_CONF0, 
+       SWITCH_WRITE(SWITCH_REG_PORT_CONF0,
            (SWITCH_PORTS_HW << PORT_CONF0_DP_SHIFT));
 
        /* disable CPU port */
@@ -159,7 +161,7 @@ static void switch_init(void)
        /* disable GPIO lines */
        SWITCH_WRITE(SWITCH_REG_GPIO_CONF0, 0);
        SWITCH_WRITE(SWITCH_REG_GPIO_CONF2, 0);
-       
+
        /* disable LED lines */
        SWITCH_WRITE(SWITCH_REG_PORT0_LED, 0);
        SWITCH_WRITE(SWITCH_REG_PORT1_LED, 0);