--- /dev/null
+--- a/drivers/net/Kconfig
++++ b/drivers/net/Kconfig
+@@ -251,6 +251,12 @@ config AX88796_93CX6
+ help
+ Select this if your platform comes with an external 93CX6 eeprom.
+
++config AR231X_ETHERNET
++ tristate "AR231x Ethernet support"
++ depends on ATHEROS_AR231X
++ help
++ Support for the AR231x/531x ethernet controller
++
+ config MACE
+ tristate "MACE (Power Mac ethernet) support"
+ depends on PPC_PMAC && PPC32
+--- a/drivers/net/Makefile
++++ b/drivers/net/Makefile
+@@ -224,6 +224,7 @@ obj-$(CONFIG_EQUALIZER) += eql.o
+ obj-$(CONFIG_KORINA) += korina.o
+ obj-$(CONFIG_MIPS_JAZZ_SONIC) += jazzsonic.o
+ obj-$(CONFIG_MIPS_AU1X00_ENET) += au1000_eth.o
++obj-$(CONFIG_AR231X_ETHERNET) += ar231x.o
+ obj-$(CONFIG_MIPS_SIM_NET) += mipsnet.o
+ obj-$(CONFIG_SGI_IOC3_ETH) += ioc3-eth.o
+ obj-$(CONFIG_DECLANCE) += declance.o
+--- /dev/null
++++ b/drivers/net/ar231x.c
+@@ -0,0 +1,1278 @@
++/*
++ * ar231x.c: Linux driver for the Atheros AR231x Ethernet device.
++ *
++ * Copyright (C) 2004 by Sameer Dekate <sdekate@arubanetworks.com>
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
++ *
++ * Thanks to Atheros for providing hardware and documentation
++ * enabling me to write this driver.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * Additional credits:
++ * This code is taken from John Taylor's Sibyte driver and then
++ * modified for the AR2313.
++ */
++
++#include <linux/module.h>
++#include <linux/version.h>
++#include <linux/types.h>
++#include <linux/errno.h>
++#include <linux/ioport.h>
++#include <linux/pci.h>
++#include <linux/netdevice.h>
++#include <linux/etherdevice.h>
++#include <linux/skbuff.h>
++#include <linux/init.h>
++#include <linux/delay.h>
++#include <linux/mm.h>
++#include <linux/highmem.h>
++#include <linux/sockios.h>
++#include <linux/pkt_sched.h>
++#include <linux/mii.h>
++#include <linux/phy.h>
++#include <linux/ethtool.h>
++#include <linux/ctype.h>
++#include <linux/platform_device.h>
++
++#include <net/sock.h>
++#include <net/ip.h>
++
++#include <asm/system.h>
++#include <asm/io.h>
++#include <asm/irq.h>
++#include <asm/byteorder.h>
++#include <asm/uaccess.h>
++#include <asm/bootinfo.h>
++
++#define AR2313_MTU 1692
++#define AR2313_PRIOS 1
++#define AR2313_QUEUES (2*AR2313_PRIOS)
++#define AR2313_DESCR_ENTRIES 64
++
++
++#ifndef min
++#define min(a,b) (((a)<(b))?(a):(b))
++#endif
++
++#ifndef SMP_CACHE_BYTES
++#define SMP_CACHE_BYTES L1_CACHE_BYTES
++#endif
++
++#define AR2313_MBOX_SET_BIT 0x8
++
++#include "ar231x.h"
++
++/*
++ * New interrupt handler strategy:
++ *
++ * An old interrupt handler worked using the traditional method of
++ * replacing an skbuff with a new one when a packet arrives. However
++ * the rx rings do not need to contain a static number of buffer
++ * descriptors, thus it makes sense to move the memory allocation out
++ * of the main interrupt handler and do it in a bottom half handler
++ * and only allocate new buffers when the number of buffers in the
++ * ring is below a certain threshold. In order to avoid starving the
++ * NIC under heavy load it is however necessary to force allocation
++ * when hitting a minimum threshold. The strategy for alloction is as
++ * follows:
++ *
++ * RX_LOW_BUF_THRES - allocate buffers in the bottom half
++ * RX_PANIC_LOW_THRES - we are very low on buffers, allocate
++ * the buffers in the interrupt handler
++ * RX_RING_THRES - maximum number of buffers in the rx ring
++ *
++ * One advantagous side effect of this allocation approach is that the
++ * entire rx processing can be done without holding any spin lock
++ * since the rx rings and registers are totally independent of the tx
++ * ring and its registers. This of course includes the kmalloc's of
++ * new skb's. Thus start_xmit can run in parallel with rx processing
++ * and the memory allocation on SMP systems.
++ *
++ * Note that running the skb reallocation in a bottom half opens up
++ * another can of races which needs to be handled properly. In
++ * particular it can happen that the interrupt handler tries to run
++ * the reallocation while the bottom half is either running on another
++ * CPU or was interrupted on the same CPU. To get around this the
++ * driver uses bitops to prevent the reallocation routines from being
++ * reentered.
++ *
++ * TX handling can also be done without holding any spin lock, wheee
++ * this is fun! since tx_csm is only written to by the interrupt
++ * handler.
++ */
++
++/*
++ * Threshold values for RX buffer allocation - the low water marks for
++ * when to start refilling the rings are set to 75% of the ring
++ * sizes. It seems to make sense to refill the rings entirely from the
++ * intrrupt handler once it gets below the panic threshold, that way
++ * we don't risk that the refilling is moved to another CPU when the
++ * one running the interrupt handler just got the slab code hot in its
++ * cache.
++ */
++#define RX_RING_SIZE AR2313_DESCR_ENTRIES
++#define RX_PANIC_THRES (RX_RING_SIZE/4)
++#define RX_LOW_THRES ((3*RX_RING_SIZE)/4)
++#define CRC_LEN 4
++#define RX_OFFSET 2
++
++#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE)
++#define VLAN_HDR 4
++#else
++#define VLAN_HDR 0
++#endif
++
++#define AR2313_BUFSIZE (AR2313_MTU + VLAN_HDR + ETH_HLEN + CRC_LEN + RX_OFFSET)
++
++#ifdef MODULE
++MODULE_LICENSE("GPL");
++MODULE_AUTHOR("Sameer Dekate <sdekate@arubanetworks.com>, Imre Kaloz <kaloz@openwrt.org>, Felix Fietkau <nbd@openwrt.org>");
++MODULE_DESCRIPTION("AR231x Ethernet driver");
++#endif
++
++#define virt_to_phys(x) ((u32)(x) & 0x1fffffff)
++
++// prototypes
++static void ar231x_halt(struct net_device *dev);
++static void rx_tasklet_func(unsigned long data);
++static void rx_tasklet_cleanup(struct net_device *dev);
++static void ar231x_multicast_list(struct net_device *dev);
++static void ar231x_tx_timeout(struct net_device *dev);
++
++static int ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum);
++static int ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, u16 value);
++static int ar231x_mdiobus_reset(struct mii_bus *bus);
++static int ar231x_mdiobus_probe (struct net_device *dev);
++static void ar231x_adjust_link(struct net_device *dev);
++
++#ifndef ERR
++#define ERR(fmt, args...) printk("%s: " fmt, __func__, ##args)
++#endif
++
++static const struct net_device_ops ar231x_ops = {
++ .ndo_open = ar231x_open,
++ .ndo_stop = ar231x_close,
++ .ndo_start_xmit = ar231x_start_xmit,
++ .ndo_set_multicast_list = ar231x_multicast_list,
++ .ndo_do_ioctl = ar231x_ioctl,
++ .ndo_change_mtu = eth_change_mtu,
++ .ndo_validate_addr = eth_validate_addr,
++ .ndo_set_mac_address = eth_mac_addr,
++ .ndo_tx_timeout = ar231x_tx_timeout,
++};
++
++int __init ar231x_probe(struct platform_device *pdev)
++{
++ struct net_device *dev;
++ struct ar231x_private *sp;
++ struct resource *res;
++ unsigned long ar_eth_base;
++ char buf[64];
++
++ dev = alloc_etherdev(sizeof(struct ar231x_private));
++
++ if (dev == NULL) {
++ printk(KERN_ERR
++ "ar231x: Unable to allocate net_device structure!\n");
++ return -ENOMEM;
++ }
++
++ platform_set_drvdata(pdev, dev);
++
++ sp = netdev_priv(dev);
++ sp->dev = dev;
++ sp->cfg = pdev->dev.platform_data;
++
++ sprintf(buf, "eth%d_membase", pdev->id);
++ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, buf);
++ if (!res)
++ return -ENODEV;
++
++ sp->link = 0;
++ ar_eth_base = res->start;
++
++ sprintf(buf, "eth%d_irq", pdev->id);
++ dev->irq = platform_get_irq_byname(pdev, buf);
++
++ spin_lock_init(&sp->lock);
++
++ dev->features |= NETIF_F_HIGHDMA;
++ dev->netdev_ops = &ar231x_ops;
++
++ tasklet_init(&sp->rx_tasklet, rx_tasklet_func, (unsigned long) dev);
++ tasklet_disable(&sp->rx_tasklet);
++
++ sp->eth_regs =
++ ioremap_nocache(virt_to_phys(ar_eth_base), sizeof(*sp->eth_regs));
++ if (!sp->eth_regs) {
++ printk("Can't remap eth registers\n");
++ return (-ENXIO);
++ }
++
++ /*
++ * When there's only one MAC, PHY regs are typically on ENET0,
++ * even though the MAC might be on ENET1.
++ * Needto remap PHY regs separately in this case
++ */
++ if (virt_to_phys(ar_eth_base) == virt_to_phys(sp->phy_regs))
++ sp->phy_regs = sp->eth_regs;
++ else {
++ sp->phy_regs =
++ ioremap_nocache(virt_to_phys(sp->cfg->phy_base),
++ sizeof(*sp->phy_regs));
++ if (!sp->phy_regs) {
++ printk("Can't remap phy registers\n");
++ return (-ENXIO);
++ }
++ }
++
++ sp->dma_regs =
++ ioremap_nocache(virt_to_phys(ar_eth_base + 0x1000),
++ sizeof(*sp->dma_regs));
++ dev->base_addr = (unsigned int) sp->dma_regs;
++ if (!sp->dma_regs) {
++ printk("Can't remap DMA registers\n");
++ return (-ENXIO);
++ }
++
++ sp->int_regs = ioremap_nocache(virt_to_phys(sp->cfg->reset_base), 4);
++ if (!sp->int_regs) {
++ printk("Can't remap INTERRUPT registers\n");
++ return (-ENXIO);
++ }
++
++ strncpy(sp->name, "Atheros AR231x", sizeof(sp->name) - 1);
++ sp->name[sizeof(sp->name) - 1] = '\0';
++ memcpy(dev->dev_addr, sp->cfg->macaddr, 6);
++
++ if (ar231x_init(dev)) {
++ /*
++ * ar231x_init() calls ar231x_init_cleanup() on error.
++ */
++ kfree(dev);
++ return -ENODEV;
++ }
++
++ if (register_netdev(dev)) {
++ printk("%s: register_netdev failed\n", __func__);
++ return -1;
++ }
++
++ printk("%s: %s: %02x:%02x:%02x:%02x:%02x:%02x, irq %d\n",
++ dev->name, sp->name,
++ dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
++ dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5], dev->irq);
++
++ sp->mii_bus = mdiobus_alloc();
++ if (sp->mii_bus == NULL)
++ return -1;
++
++ sp->mii_bus->priv = dev;
++ sp->mii_bus->read = ar231x_mdiobus_read;
++ sp->mii_bus->write = ar231x_mdiobus_write;
++ sp->mii_bus->reset = ar231x_mdiobus_reset;
++ sp->mii_bus->name = "ar231x_eth_mii";
++ snprintf(sp->mii_bus->id, MII_BUS_ID_SIZE, "%d", pdev->id);
++ sp->mii_bus->irq = kmalloc(sizeof(int), GFP_KERNEL);
++ *sp->mii_bus->irq = PHY_POLL;
++
++ mdiobus_register(sp->mii_bus);
++
++ if (ar231x_mdiobus_probe(dev) != 0) {
++ printk(KERN_ERR "%s: mdiobus_probe failed\n", dev->name);
++ rx_tasklet_cleanup(dev);
++ ar231x_init_cleanup(dev);
++ unregister_netdev(dev);
++ kfree(dev);
++ return -ENODEV;
++ }
++
++ /* start link poll timer */
++ ar231x_setup_timer(dev);
++
++ return 0;
++}
++
++
++static void ar231x_multicast_list(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ unsigned int filter;
++
++ filter = sp->eth_regs->mac_control;
++
++ if (dev->flags & IFF_PROMISC)
++ filter |= MAC_CONTROL_PR;
++ else
++ filter &= ~MAC_CONTROL_PR;
++ if ((dev->flags & IFF_ALLMULTI) || (netdev_mc_count(dev) > 0))
++ filter |= MAC_CONTROL_PM;
++ else
++ filter &= ~MAC_CONTROL_PM;
++
++ sp->eth_regs->mac_control = filter;
++}
++
++static void rx_tasklet_cleanup(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++
++ /*
++ * Tasklet may be scheduled. Need to get it removed from the list
++ * since we're about to free the struct.
++ */
++
++ sp->unloading = 1;
++ tasklet_enable(&sp->rx_tasklet);
++ tasklet_kill(&sp->rx_tasklet);
++}
++
++static int __devexit ar231x_remove(struct platform_device *pdev)
++{
++ struct net_device *dev = platform_get_drvdata(pdev);
++ struct ar231x_private *sp = netdev_priv(dev);
++ rx_tasklet_cleanup(dev);
++ ar231x_init_cleanup(dev);
++ unregister_netdev(dev);
++ mdiobus_unregister(sp->mii_bus);
++ mdiobus_free(sp->mii_bus);
++ kfree(dev);
++ return 0;
++}
++
++
++/*
++ * Restart the AR2313 ethernet controller.
++ */
++static int ar231x_restart(struct net_device *dev)
++{
++ /* disable interrupts */
++ disable_irq(dev->irq);
++
++ /* stop mac */
++ ar231x_halt(dev);
++
++ /* initialize */
++ ar231x_init(dev);
++
++ /* enable interrupts */
++ enable_irq(dev->irq);
++
++ return 0;
++}
++
++static struct platform_driver ar231x_driver = {
++ .driver.name = "ar231x-eth",
++ .probe = ar231x_probe,
++ .remove = __devexit_p(ar231x_remove),
++};
++
++int __init ar231x_module_init(void)
++{
++ return platform_driver_register(&ar231x_driver);
++}
++
++void __exit ar231x_module_cleanup(void)
++{
++ platform_driver_unregister(&ar231x_driver);
++}
++
++module_init(ar231x_module_init);
++module_exit(ar231x_module_cleanup);
++
++
++static void ar231x_free_descriptors(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ if (sp->rx_ring != NULL) {
++ kfree((void *) KSEG0ADDR(sp->rx_ring));
++ sp->rx_ring = NULL;
++ sp->tx_ring = NULL;
++ }
++}
++
++
++static int ar231x_allocate_descriptors(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ int size;
++ int j;
++ ar231x_descr_t *space;
++
++ if (sp->rx_ring != NULL) {
++ printk("%s: already done.\n", __FUNCTION__);
++ return 0;
++ }
++
++ size =
++ (sizeof(ar231x_descr_t) * (AR2313_DESCR_ENTRIES * AR2313_QUEUES));
++ space = kmalloc(size, GFP_KERNEL);
++ if (space == NULL)
++ return 1;
++
++ /* invalidate caches */
++ dma_cache_inv((unsigned int) space, size);
++
++ /* now convert pointer to KSEG1 */
++ space = (ar231x_descr_t *) KSEG1ADDR(space);
++
++ memset((void *) space, 0, size);
++
++ sp->rx_ring = space;
++ space += AR2313_DESCR_ENTRIES;
++
++ sp->tx_ring = space;
++ space += AR2313_DESCR_ENTRIES;
++
++ /* Initialize the transmit Descriptors */
++ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
++ ar231x_descr_t *td = &sp->tx_ring[j];
++ td->status = 0;
++ td->devcs = DMA_TX1_CHAINED;
++ td->addr = 0;
++ td->descr =
++ virt_to_phys(&sp->
++ tx_ring[(j + 1) & (AR2313_DESCR_ENTRIES - 1)]);
++ }
++
++ return 0;
++}
++
++
++/*
++ * Generic cleanup handling data allocated during init. Used when the
++ * module is unloaded or if an error occurs during initialization
++ */
++static void ar231x_init_cleanup(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ struct sk_buff *skb;
++ int j;
++
++ ar231x_free_descriptors(dev);
++
++ if (sp->eth_regs)
++ iounmap((void *) sp->eth_regs);
++ if (sp->dma_regs)
++ iounmap((void *) sp->dma_regs);
++
++ if (sp->rx_skb) {
++ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
++ skb = sp->rx_skb[j];
++ if (skb) {
++ sp->rx_skb[j] = NULL;
++ dev_kfree_skb(skb);
++ }
++ }
++ kfree(sp->rx_skb);
++ sp->rx_skb = NULL;
++ }
++
++ if (sp->tx_skb) {
++ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
++ skb = sp->tx_skb[j];
++ if (skb) {
++ sp->tx_skb[j] = NULL;
++ dev_kfree_skb(skb);
++ }
++ }
++ kfree(sp->tx_skb);
++ sp->tx_skb = NULL;
++ }
++}
++
++static int ar231x_setup_timer(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++
++ init_timer(&sp->link_timer);
++
++ sp->link_timer.function = ar231x_link_timer_fn;
++ sp->link_timer.data = (int) dev;
++ sp->link_timer.expires = jiffies + HZ;
++
++ add_timer(&sp->link_timer);
++ return 0;
++
++}
++
++static void ar231x_link_timer_fn(unsigned long data)
++{
++ struct net_device *dev = (struct net_device *) data;
++ struct ar231x_private *sp = netdev_priv(dev);
++
++ // see if the link status changed
++ // This was needed to make sure we set the PHY to the
++ // autonegotiated value of half or full duplex.
++ ar231x_check_link(dev);
++
++ // Loop faster when we don't have link.
++ // This was needed to speed up the AP bootstrap time.
++ if (sp->link == 0) {
++ mod_timer(&sp->link_timer, jiffies + HZ / 2);
++ } else {
++ mod_timer(&sp->link_timer, jiffies + LINK_TIMER);
++ }
++}
++
++static void ar231x_check_link(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ u16 phyData;
++
++ phyData = ar231x_mdiobus_read(sp->mii_bus, sp->phy, MII_BMSR);
++ if (sp->phyData != phyData) {
++ if (phyData & BMSR_LSTATUS) {
++ /* link is present, ready link partner ability to deterine
++ duplexity */
++ int duplex = 0;
++ u16 reg;
++
++ sp->link = 1;
++ reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy, MII_BMCR);
++ if (reg & BMCR_ANENABLE) {
++ /* auto neg enabled */
++ reg = ar231x_mdiobus_read(sp->mii_bus, sp->phy, MII_LPA);
++ duplex = (reg & (LPA_100FULL | LPA_10FULL)) ? 1 : 0;
++ } else {
++ /* no auto neg, just read duplex config */
++ duplex = (reg & BMCR_FULLDPLX) ? 1 : 0;
++ }
++
++ printk(KERN_INFO "%s: Configuring MAC for %s duplex\n",
++ dev->name, (duplex) ? "full" : "half");
++
++ if (duplex) {
++ /* full duplex */
++ sp->eth_regs->mac_control =
++ ((sp->eth_regs->
++ mac_control | MAC_CONTROL_F) & ~MAC_CONTROL_DRO);
++ } else {
++ /* half duplex */
++ sp->eth_regs->mac_control =
++ ((sp->eth_regs->
++ mac_control | MAC_CONTROL_DRO) & ~MAC_CONTROL_F);
++ }
++ } else {
++ /* no link */
++ sp->link = 0;
++ }
++ sp->phyData = phyData;
++ }
++}
++
++static int ar231x_reset_reg(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ unsigned int ethsal, ethsah;
++ unsigned int flags;
++
++ *sp->int_regs |= sp->cfg->reset_mac;
++ mdelay(10);
++ *sp->int_regs &= ~sp->cfg->reset_mac;
++ mdelay(10);
++ *sp->int_regs |= sp->cfg->reset_phy;
++ mdelay(10);
++ *sp->int_regs &= ~sp->cfg->reset_phy;
++ mdelay(10);
++
++ sp->dma_regs->bus_mode = (DMA_BUS_MODE_SWR);
++ mdelay(10);
++ sp->dma_regs->bus_mode =
++ ((32 << DMA_BUS_MODE_PBL_SHIFT) | DMA_BUS_MODE_BLE);
++
++ /* enable interrupts */
++ sp->dma_regs->intr_ena = (DMA_STATUS_AIS |
++ DMA_STATUS_NIS |
++ DMA_STATUS_RI |
++ DMA_STATUS_TI | DMA_STATUS_FBE);
++ sp->dma_regs->xmt_base = virt_to_phys(sp->tx_ring);
++ sp->dma_regs->rcv_base = virt_to_phys(sp->rx_ring);
++ sp->dma_regs->control =
++ (DMA_CONTROL_SR | DMA_CONTROL_ST | DMA_CONTROL_SF);
++
++ sp->eth_regs->flow_control = (FLOW_CONTROL_FCE);
++ sp->eth_regs->vlan_tag = (0x8100);
++
++ /* Enable Ethernet Interface */
++ flags = (MAC_CONTROL_TE | /* transmit enable */
++ MAC_CONTROL_PM | /* pass mcast */
++ MAC_CONTROL_F | /* full duplex */
++ MAC_CONTROL_HBD); /* heart beat disabled */
++
++ if (dev->flags & IFF_PROMISC) { /* set promiscuous mode */
++ flags |= MAC_CONTROL_PR;
++ }
++ sp->eth_regs->mac_control = flags;
++
++ /* Set all Ethernet station address registers to their initial values */
++ ethsah = ((((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
++ (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF));
++
++ ethsal = ((((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
++ (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
++ (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
++ (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF));
++
++ sp->eth_regs->mac_addr[0] = ethsah;
++ sp->eth_regs->mac_addr[1] = ethsal;
++
++ mdelay(10);
++
++ return (0);
++}
++
++
++static int ar231x_init(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ int ecode = 0;
++
++ /*
++ * Allocate descriptors
++ */
++ if (ar231x_allocate_descriptors(dev)) {
++ printk("%s: %s: ar231x_allocate_descriptors failed\n",
++ dev->name, __FUNCTION__);
++ ecode = -EAGAIN;
++ goto init_error;
++ }
++
++ /*
++ * Get the memory for the skb rings.
++ */
++ if (sp->rx_skb == NULL) {
++ sp->rx_skb =
++ kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
++ GFP_KERNEL);
++ if (!(sp->rx_skb)) {
++ printk("%s: %s: rx_skb kmalloc failed\n",
++ dev->name, __FUNCTION__);
++ ecode = -EAGAIN;
++ goto init_error;
++ }
++ }
++ memset(sp->rx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
++
++ if (sp->tx_skb == NULL) {
++ sp->tx_skb =
++ kmalloc(sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES,
++ GFP_KERNEL);
++ if (!(sp->tx_skb)) {
++ printk("%s: %s: tx_skb kmalloc failed\n",
++ dev->name, __FUNCTION__);
++ ecode = -EAGAIN;
++ goto init_error;
++ }
++ }
++ memset(sp->tx_skb, 0, sizeof(struct sk_buff *) * AR2313_DESCR_ENTRIES);
++
++ /*
++ * Set tx_csm before we start receiving interrupts, otherwise
++ * the interrupt handler might think it is supposed to process
++ * tx ints before we are up and running, which may cause a null
++ * pointer access in the int handler.
++ */
++ sp->rx_skbprd = 0;
++ sp->cur_rx = 0;
++ sp->tx_prd = 0;
++ sp->tx_csm = 0;
++
++ /*
++ * Zero the stats before starting the interface
++ */
++ memset(&dev->stats, 0, sizeof(dev->stats));
++
++ /*
++ * We load the ring here as there seem to be no way to tell the
++ * firmware to wipe the ring without re-initializing it.
++ */
++ ar231x_load_rx_ring(dev, RX_RING_SIZE);
++
++ /*
++ * Init hardware
++ */
++ ar231x_reset_reg(dev);
++
++ /*
++ * Get the IRQ
++ */
++ ecode =
++ request_irq(dev->irq, &ar231x_interrupt,
++ IRQF_DISABLED | IRQF_SAMPLE_RANDOM,
++ dev->name, dev);
++ if (ecode) {
++ printk(KERN_WARNING "%s: %s: Requested IRQ %d is busy\n",
++ dev->name, __FUNCTION__, dev->irq);
++ goto init_error;
++ }
++
++
++ tasklet_enable(&sp->rx_tasklet);
++
++ return 0;
++
++ init_error:
++ ar231x_init_cleanup(dev);
++ return ecode;
++}
++
++/*
++ * Load the rx ring.
++ *
++ * Loading rings is safe without holding the spin lock since this is
++ * done only before the device is enabled, thus no interrupts are
++ * generated and by the interrupt handler/tasklet handler.
++ */
++static void ar231x_load_rx_ring(struct net_device *dev, int nr_bufs)
++{
++
++ struct ar231x_private *sp = netdev_priv(dev);
++ short i, idx;
++
++ idx = sp->rx_skbprd;
++
++ for (i = 0; i < nr_bufs; i++) {
++ struct sk_buff *skb;
++ ar231x_descr_t *rd;
++
++ if (sp->rx_skb[idx])
++ break;
++
++ skb = netdev_alloc_skb(dev, AR2313_BUFSIZE);
++ if (!skb) {
++ printk("\n\n\n\n %s: No memory in system\n\n\n\n",
++ __FUNCTION__);
++ break;
++ }
++
++ /*
++ * Make sure IP header starts on a fresh cache line.
++ */
++ skb->dev = dev;
++ skb_reserve(skb, RX_OFFSET);
++ sp->rx_skb[idx] = skb;
++
++ rd = (ar231x_descr_t *) & sp->rx_ring[idx];
++
++ /* initialize dma descriptor */
++ rd->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
++ DMA_RX1_CHAINED);
++ rd->addr = virt_to_phys(skb->data);
++ rd->descr =
++ virt_to_phys(&sp->
++ rx_ring[(idx + 1) & (AR2313_DESCR_ENTRIES - 1)]);
++ rd->status = DMA_RX_OWN;
++
++ idx = DSC_NEXT(idx);
++ }
++
++ if (i)
++ sp->rx_skbprd = idx;
++
++ return;
++}
++
++#define AR2313_MAX_PKTS_PER_CALL 64
++
++static int ar231x_rx_int(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ struct sk_buff *skb, *skb_new;
++ ar231x_descr_t *rxdesc;
++ unsigned int status;
++ u32 idx;
++ int pkts = 0;
++ int rval;
++
++ idx = sp->cur_rx;
++
++ /* process at most the entire ring and then wait for another interrupt
++ */
++ while (1) {
++
++ rxdesc = &sp->rx_ring[idx];
++ status = rxdesc->status;
++ if (status & DMA_RX_OWN) {
++ /* SiByte owns descriptor or descr not yet filled in */
++ rval = 0;
++ break;
++ }
++
++ if (++pkts > AR2313_MAX_PKTS_PER_CALL) {
++ rval = 1;
++ break;
++ }
++
++ if ((status & DMA_RX_ERROR) && !(status & DMA_RX_LONG)) {
++ dev->stats.rx_errors++;
++ dev->stats.rx_dropped++;
++
++ /* add statistics counters */
++ if (status & DMA_RX_ERR_CRC)
++ dev->stats.rx_crc_errors++;
++ if (status & DMA_RX_ERR_COL)
++ dev->stats.rx_over_errors++;
++ if (status & DMA_RX_ERR_LENGTH)
++ dev->stats.rx_length_errors++;
++ if (status & DMA_RX_ERR_RUNT)
++ dev->stats.rx_over_errors++;
++ if (status & DMA_RX_ERR_DESC)
++ dev->stats.rx_over_errors++;
++
++ } else {
++ /* alloc new buffer. */
++ skb_new = netdev_alloc_skb(dev, AR2313_BUFSIZE + RX_OFFSET);
++ if (skb_new != NULL) {
++
++ skb = sp->rx_skb[idx];
++ /* set skb */
++ skb_put(skb,
++ ((status >> DMA_RX_LEN_SHIFT) & 0x3fff) - CRC_LEN);
++
++ dev->stats.rx_bytes += skb->len;
++ skb->protocol = eth_type_trans(skb, dev);
++ /* pass the packet to upper layers */
++ netif_rx(skb);
++
++ skb_new->dev = dev;
++ /* 16 bit align */
++ skb_reserve(skb_new, RX_OFFSET);
++ /* reset descriptor's curr_addr */
++ rxdesc->addr = virt_to_phys(skb_new->data);
++
++ dev->stats.rx_packets++;
++ sp->rx_skb[idx] = skb_new;
++ } else {
++ dev->stats.rx_dropped++;
++ }
++ }
++
++ rxdesc->devcs = ((AR2313_BUFSIZE << DMA_RX1_BSIZE_SHIFT) |
++ DMA_RX1_CHAINED);
++ rxdesc->status = DMA_RX_OWN;
++
++ idx = DSC_NEXT(idx);
++ }
++
++ sp->cur_rx = idx;
++
++ return rval;
++}
++
++
++static void ar231x_tx_int(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ u32 idx;
++ struct sk_buff *skb;
++ ar231x_descr_t *txdesc;
++ unsigned int status = 0;
++
++ idx = sp->tx_csm;
++
++ while (idx != sp->tx_prd) {
++ txdesc = &sp->tx_ring[idx];
++
++ if ((status = txdesc->status) & DMA_TX_OWN) {
++ /* ar231x dma still owns descr */
++ break;
++ }
++ /* done with this descriptor */
++ dma_unmap_single(NULL, txdesc->addr,
++ txdesc->devcs & DMA_TX1_BSIZE_MASK,
++ DMA_TO_DEVICE);
++ txdesc->status = 0;
++
++ if (status & DMA_TX_ERROR) {
++ dev->stats.tx_errors++;
++ dev->stats.tx_dropped++;
++ if (status & DMA_TX_ERR_UNDER)
++ dev->stats.tx_fifo_errors++;
++ if (status & DMA_TX_ERR_HB)
++ dev->stats.tx_heartbeat_errors++;
++ if (status & (DMA_TX_ERR_LOSS | DMA_TX_ERR_LINK))
++ dev->stats.tx_carrier_errors++;
++ if (status & (DMA_TX_ERR_LATE |
++ DMA_TX_ERR_COL |
++ DMA_TX_ERR_JABBER | DMA_TX_ERR_DEFER))
++ dev->stats.tx_aborted_errors++;
++ } else {
++ /* transmit OK */
++ dev->stats.tx_packets++;
++ }
++
++ skb = sp->tx_skb[idx];
++ sp->tx_skb[idx] = NULL;
++ idx = DSC_NEXT(idx);
++ dev->stats.tx_bytes += skb->len;
++ dev_kfree_skb_irq(skb);
++ }
++
++ sp->tx_csm = idx;
++
++ return;
++}
++
++
++static void rx_tasklet_func(unsigned long data)
++{
++ struct net_device *dev = (struct net_device *) data;
++ struct ar231x_private *sp = netdev_priv(dev);
++
++ if (sp->unloading) {
++ return;
++ }
++
++ if (ar231x_rx_int(dev)) {
++ tasklet_hi_schedule(&sp->rx_tasklet);
++ } else {
++ unsigned long flags;
++ spin_lock_irqsave(&sp->lock, flags);
++ sp->dma_regs->intr_ena |= DMA_STATUS_RI;
++ spin_unlock_irqrestore(&sp->lock, flags);
++ }
++}
++
++static void rx_schedule(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++
++ sp->dma_regs->intr_ena &= ~DMA_STATUS_RI;
++
++ tasklet_hi_schedule(&sp->rx_tasklet);
++}
++
++static irqreturn_t ar231x_interrupt(int irq, void *dev_id)
++{
++ struct net_device *dev = (struct net_device *) dev_id;
++ struct ar231x_private *sp = netdev_priv(dev);
++ unsigned int status, enabled;
++
++ /* clear interrupt */
++ /*
++ * Don't clear RI bit if currently disabled.
++ */
++ status = sp->dma_regs->status;
++ enabled = sp->dma_regs->intr_ena;
++ sp->dma_regs->status = status & enabled;
++
++ if (status & DMA_STATUS_NIS) {
++ /* normal status */
++ /*
++ * Don't schedule rx processing if interrupt
++ * is already disabled.
++ */
++ if (status & enabled & DMA_STATUS_RI) {
++ /* receive interrupt */
++ rx_schedule(dev);
++ }
++ if (status & DMA_STATUS_TI) {
++ /* transmit interrupt */
++ ar231x_tx_int(dev);
++ }
++ }
++
++ /* abnormal status */
++ if (status & (DMA_STATUS_FBE | DMA_STATUS_TPS)) {
++ ar231x_restart(dev);
++ }
++ return IRQ_HANDLED;
++}
++
++
++static int ar231x_open(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ unsigned int ethsal, ethsah;
++
++ /* reset the hardware, in case the MAC address changed */
++ ethsah = ((((u_int) (dev->dev_addr[5]) << 8) & (u_int) 0x0000FF00) |
++ (((u_int) (dev->dev_addr[4]) << 0) & (u_int) 0x000000FF));
++
++ ethsal = ((((u_int) (dev->dev_addr[3]) << 24) & (u_int) 0xFF000000) |
++ (((u_int) (dev->dev_addr[2]) << 16) & (u_int) 0x00FF0000) |
++ (((u_int) (dev->dev_addr[1]) << 8) & (u_int) 0x0000FF00) |
++ (((u_int) (dev->dev_addr[0]) << 0) & (u_int) 0x000000FF));
++
++ sp->eth_regs->mac_addr[0] = ethsah;
++ sp->eth_regs->mac_addr[1] = ethsal;
++
++ mdelay(10);
++
++ dev->mtu = 1500;
++ netif_start_queue(dev);
++
++ sp->eth_regs->mac_control |= MAC_CONTROL_RE;
++
++ return 0;
++}
++
++static void ar231x_tx_timeout(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ unsigned long flags;
++
++ spin_lock_irqsave(&sp->lock, flags);
++ ar231x_restart(dev);
++ spin_unlock_irqrestore(&sp->lock, flags);
++}
++
++static void ar231x_halt(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ int j;
++
++ tasklet_disable(&sp->rx_tasklet);
++
++ /* kill the MAC */
++ sp->eth_regs->mac_control &= ~(MAC_CONTROL_RE | /* disable Receives */
++ MAC_CONTROL_TE); /* disable Transmits */
++ /* stop dma */
++ sp->dma_regs->control = 0;
++ sp->dma_regs->bus_mode = DMA_BUS_MODE_SWR;
++
++ /* place phy and MAC in reset */
++ *sp->int_regs |= (sp->cfg->reset_mac | sp->cfg->reset_phy);
++
++ /* free buffers on tx ring */
++ for (j = 0; j < AR2313_DESCR_ENTRIES; j++) {
++ struct sk_buff *skb;
++ ar231x_descr_t *txdesc;
++
++ txdesc = &sp->tx_ring[j];
++ txdesc->descr = 0;
++
++ skb = sp->tx_skb[j];
++ if (skb) {
++ dev_kfree_skb(skb);
++ sp->tx_skb[j] = NULL;
++ }
++ }
++}
++
++/*
++ * close should do nothing. Here's why. It's called when
++ * 'ifconfig bond0 down' is run. If it calls free_irq then
++ * the irq is gone forever ! When bond0 is made 'up' again,
++ * the ar231x_open () does not call request_irq (). Worse,
++ * the call to ar231x_halt() generates a WDOG reset due to
++ * the write to 'sp->int_regs' and the box reboots.
++ * Commenting this out is good since it allows the
++ * system to resume when bond0 is made up again.
++ */
++static int ar231x_close(struct net_device *dev)
++{
++#if 0
++ /*
++ * Disable interrupts
++ */
++ disable_irq(dev->irq);
++
++ /*
++ * Without (or before) releasing irq and stopping hardware, this
++ * is an absolute non-sense, by the way. It will be reset instantly
++ * by the first irq.
++ */
++ netif_stop_queue(dev);
++
++ /* stop the MAC and DMA engines */
++ ar231x_halt(dev);
++
++ /* release the interrupt */
++ free_irq(dev->irq, dev);
++
++#endif
++ return 0;
++}
++
++static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ ar231x_descr_t *td;
++ u32 idx;
++
++ idx = sp->tx_prd;
++ td = &sp->tx_ring[idx];
++
++ if (td->status & DMA_TX_OWN) {
++ /* free skbuf and lie to the caller that we sent it out */
++ dev->stats.tx_dropped++;
++ dev_kfree_skb(skb);
++
++ /* restart transmitter in case locked */
++ sp->dma_regs->xmt_poll = 0;
++ return 0;
++ }
++
++ /* Setup the transmit descriptor. */
++ td->devcs = ((skb->len << DMA_TX1_BSIZE_SHIFT) |
++ (DMA_TX1_LS | DMA_TX1_IC | DMA_TX1_CHAINED));
++ td->addr = dma_map_single(NULL, skb->data, skb->len, DMA_TO_DEVICE);
++ td->status = DMA_TX_OWN;
++
++ /* kick transmitter last */
++ sp->dma_regs->xmt_poll = 0;
++
++ sp->tx_skb[idx] = skb;
++ idx = DSC_NEXT(idx);
++ sp->tx_prd = idx;
++
++ return 0;
++}
++
++static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
++{
++ struct mii_ioctl_data *data = (struct mii_ioctl_data *) &ifr->ifr_data;
++ struct ar231x_private *sp = netdev_priv(dev);
++ int ret;
++
++ switch (cmd) {
++
++ case SIOCETHTOOL:
++ spin_lock_irq(&sp->lock);
++ ret = phy_ethtool_ioctl(sp->phy_dev, (void *) ifr->ifr_data);
++ spin_unlock_irq(&sp->lock);
++ return ret;
++
++ case SIOCSIFHWADDR:
++ if (copy_from_user
++ (dev->dev_addr, ifr->ifr_data, sizeof(dev->dev_addr)))
++ return -EFAULT;
++ return 0;
++
++ case SIOCGIFHWADDR:
++ if (copy_to_user
++ (ifr->ifr_data, dev->dev_addr, sizeof(dev->dev_addr)))
++ return -EFAULT;
++ return 0;
++
++ case SIOCGMIIPHY:
++ case SIOCGMIIREG:
++ case SIOCSMIIREG:
++ return phy_mii_ioctl(sp->phy_dev, data, cmd);
++
++ default:
++ break;
++ }
++
++ return -EOPNOTSUPP;
++}
++
++static void ar231x_adjust_link(struct net_device *dev)
++{
++ struct ar231x_private *sp = netdev_priv(dev);
++ unsigned int mc;
++
++ if (!sp->phy_dev->link)
++ return;
++
++ if (sp->phy_dev->duplex != sp->oldduplex) {
++ mc = readl(&sp->eth_regs->mac_control);
++ mc &= ~(MAC_CONTROL_F | MAC_CONTROL_DRO);
++ if (sp->phy_dev->duplex)
++ mc |= MAC_CONTROL_F;
++ else
++ mc |= MAC_CONTROL_DRO;
++ writel(mc, &sp->eth_regs->mac_control);
++ sp->oldduplex = sp->phy_dev->duplex;
++ }
++}
++
++#define MII_ADDR(phy, reg) \
++ ((reg << MII_ADDR_REG_SHIFT) | (phy << MII_ADDR_PHY_SHIFT))
++
++static int
++ar231x_mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum)
++{
++ struct net_device *const dev = bus->priv;
++ struct ar231x_private *sp = netdev_priv(dev);
++ volatile ETHERNET_STRUCT *ethernet = sp->phy_regs;
++
++ ethernet->mii_addr = MII_ADDR(phy_addr, regnum);
++ while (ethernet->mii_addr & MII_ADDR_BUSY);
++ return (ethernet->mii_data >> MII_DATA_SHIFT);
++}
++
++static int
++ar231x_mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum,
++ u16 value)
++{
++ struct net_device *const dev = bus->priv;
++ struct ar231x_private *sp = netdev_priv(dev);
++ volatile ETHERNET_STRUCT *ethernet = sp->phy_regs;
++
++ while (ethernet->mii_addr & MII_ADDR_BUSY);
++ ethernet->mii_data = value << MII_DATA_SHIFT;
++ ethernet->mii_addr = MII_ADDR(phy_addr, regnum) | MII_ADDR_WRITE;
++
++ return 0;
++}
++
++static int ar231x_mdiobus_reset(struct mii_bus *bus)
++{
++ struct net_device *const dev = bus->priv;
++
++ ar231x_reset_reg(dev);
++
++ return 0;
++}
++
++static int ar231x_mdiobus_probe (struct net_device *dev)
++{
++ struct ar231x_private *const sp = netdev_priv(dev);
++ struct phy_device *phydev = NULL;
++ int phy_addr;
++
++ /* find the first (lowest address) PHY on the current MAC's MII bus */
++ for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++)
++ if (sp->mii_bus->phy_map[phy_addr]) {
++ phydev = sp->mii_bus->phy_map[phy_addr];
++ sp->phy = phy_addr;
++ break; /* break out with first one found */
++ }
++
++ if (!phydev) {
++ printk (KERN_ERR "ar231x: %s: no PHY found\n", dev->name);
++ return -1;
++ }
++
++ /* now we are supposed to have a proper phydev, to attach to... */
++ BUG_ON(!phydev);
++ BUG_ON(phydev->attached_dev);
++
++ phydev = phy_connect(dev, dev_name(&phydev->dev), &ar231x_adjust_link, 0,
++ PHY_INTERFACE_MODE_MII);
++
++ if (IS_ERR(phydev)) {
++ printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name);
++ return PTR_ERR(phydev);
++ }
++
++ /* mask with MAC supported features */
++ phydev->supported &= (SUPPORTED_10baseT_Half
++ | SUPPORTED_10baseT_Full
++ | SUPPORTED_100baseT_Half
++ | SUPPORTED_100baseT_Full
++ | SUPPORTED_Autoneg
++ /* | SUPPORTED_Pause | SUPPORTED_Asym_Pause */
++ | SUPPORTED_MII
++ | SUPPORTED_TP);
++
++ phydev->advertising = phydev->supported;
++
++ sp->oldduplex = -1;
++ sp->phy_dev = phydev;
++
++ printk(KERN_INFO "%s: attached PHY driver [%s] "
++ "(mii_bus:phy_addr=%s)\n",
++ dev->name, phydev->drv->name, dev_name(&phydev->dev));
++
++ return 0;
++}
++
+--- /dev/null
++++ b/drivers/net/ar231x.h
+@@ -0,0 +1,302 @@
++/*
++ * ar231x.h: Linux driver for the Atheros AR231x Ethernet device.
++ *
++ * Copyright (C) 2004 by Sameer Dekate <sdekate@arubanetworks.com>
++ * Copyright (C) 2006 Imre Kaloz <kaloz@openwrt.org>
++ * Copyright (C) 2006-2009 Felix Fietkau <nbd@openwrt.org>
++ *
++ * Thanks to Atheros for providing hardware and documentation
++ * enabling me to write this driver.
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ */
++
++#ifndef _AR2313_H_
++#define _AR2313_H_
++
++#include <generated/autoconf.h>
++#include <linux/bitops.h>
++#include <asm/bootinfo.h>
++#include <ar231x_platform.h>
++
++/*
++ * probe link timer - 5 secs
++ */
++#define LINK_TIMER (5*HZ)
++
++#define IS_DMA_TX_INT(X) (((X) & (DMA_STATUS_TI)) != 0)
++#define IS_DMA_RX_INT(X) (((X) & (DMA_STATUS_RI)) != 0)
++#define IS_DRIVER_OWNED(X) (((X) & (DMA_TX_OWN)) == 0)
++
++#define AR2313_TX_TIMEOUT (HZ/4)
++
++/*
++ * Rings
++ */
++#define DSC_RING_ENTRIES_SIZE (AR2313_DESCR_ENTRIES * sizeof(struct desc))
++#define DSC_NEXT(idx) ((idx + 1) & (AR2313_DESCR_ENTRIES - 1))
++
++#define AR2313_MBGET 2
++#define AR2313_MBSET 3
++#define AR2313_PCI_RECONFIG 4
++#define AR2313_PCI_DUMP 5
++#define AR2313_TEST_PANIC 6
++#define AR2313_TEST_NULLPTR 7
++#define AR2313_READ_DATA 8
++#define AR2313_WRITE_DATA 9
++#define AR2313_GET_VERSION 10
++#define AR2313_TEST_HANG 11
++#define AR2313_SYNC 12
++
++#define DMA_RX_ERR_CRC BIT(1)
++#define DMA_RX_ERR_DRIB BIT(2)
++#define DMA_RX_ERR_MII BIT(3)
++#define DMA_RX_EV2 BIT(5)
++#define DMA_RX_ERR_COL BIT(6)
++#define DMA_RX_LONG BIT(7)
++#define DMA_RX_LS BIT(8) /* last descriptor */
++#define DMA_RX_FS BIT(9) /* first descriptor */
++#define DMA_RX_MF BIT(10) /* multicast frame */
++#define DMA_RX_ERR_RUNT BIT(11) /* runt frame */
++#define DMA_RX_ERR_LENGTH BIT(12) /* length error */
++#define DMA_RX_ERR_DESC BIT(14) /* descriptor error */
++#define DMA_RX_ERROR BIT(15) /* error summary */
++#define DMA_RX_LEN_MASK 0x3fff0000
++#define DMA_RX_LEN_SHIFT 16
++#define DMA_RX_FILT BIT(30)
++#define DMA_RX_OWN BIT(31) /* desc owned by DMA controller */
++
++#define DMA_RX1_BSIZE_MASK 0x000007ff
++#define DMA_RX1_BSIZE_SHIFT 0
++#define DMA_RX1_CHAINED BIT(24)
++#define DMA_RX1_RER BIT(25)
++
++#define DMA_TX_ERR_UNDER BIT(1) /* underflow error */
++#define DMA_TX_ERR_DEFER BIT(2) /* excessive deferral */
++#define DMA_TX_COL_MASK 0x78
++#define DMA_TX_COL_SHIFT 3
++#define DMA_TX_ERR_HB BIT(7) /* hearbeat failure */
++#define DMA_TX_ERR_COL BIT(8) /* excessive collisions */
++#define DMA_TX_ERR_LATE BIT(9) /* late collision */
++#define DMA_TX_ERR_LINK BIT(10) /* no carrier */
++#define DMA_TX_ERR_LOSS BIT(11) /* loss of carrier */
++#define DMA_TX_ERR_JABBER BIT(14) /* transmit jabber timeout */
++#define DMA_TX_ERROR BIT(15) /* frame aborted */
++#define DMA_TX_OWN BIT(31) /* descr owned by DMA controller */
++
++#define DMA_TX1_BSIZE_MASK 0x000007ff
++#define DMA_TX1_BSIZE_SHIFT 0
++#define DMA_TX1_CHAINED BIT(24) /* chained descriptors */
++#define DMA_TX1_TER BIT(25) /* transmit end of ring */
++#define DMA_TX1_FS BIT(29) /* first segment */
++#define DMA_TX1_LS BIT(30) /* last segment */
++#define DMA_TX1_IC BIT(31) /* interrupt on completion */
++
++#define RCVPKT_LENGTH(X) (X >> 16) /* Received pkt Length */
++
++#define MAC_CONTROL_RE BIT(2) /* receive enable */
++#define MAC_CONTROL_TE BIT(3) /* transmit enable */
++#define MAC_CONTROL_DC BIT(5) /* Deferral check */
++#define MAC_CONTROL_ASTP BIT(8) /* Auto pad strip */
++#define MAC_CONTROL_DRTY BIT(10) /* Disable retry */
++#define MAC_CONTROL_DBF BIT(11) /* Disable bcast frames */
++#define MAC_CONTROL_LCC BIT(12) /* late collision ctrl */
++#define MAC_CONTROL_HP BIT(13) /* Hash Perfect filtering */
++#define MAC_CONTROL_HASH BIT(14) /* Unicast hash filtering */
++#define MAC_CONTROL_HO BIT(15) /* Hash only filtering */
++#define MAC_CONTROL_PB BIT(16) /* Pass Bad frames */
++#define MAC_CONTROL_IF BIT(17) /* Inverse filtering */
++#define MAC_CONTROL_PR BIT(18) /* promiscuous mode (valid frames only) */
++#define MAC_CONTROL_PM BIT(19) /* pass multicast */
++#define MAC_CONTROL_F BIT(20) /* full-duplex */
++#define MAC_CONTROL_DRO BIT(23) /* Disable Receive Own */
++#define MAC_CONTROL_HBD BIT(28) /* heart-beat disabled (MUST BE SET) */
++#define MAC_CONTROL_BLE BIT(30) /* big endian mode */
++#define MAC_CONTROL_RA BIT(31) /* receive all (valid and invalid frames) */
++
++#define MII_ADDR_BUSY BIT(0)
++#define MII_ADDR_WRITE BIT(1)
++#define MII_ADDR_REG_SHIFT 6
++#define MII_ADDR_PHY_SHIFT 11
++#define MII_DATA_SHIFT 0
++
++#define FLOW_CONTROL_FCE BIT(1)
++
++#define DMA_BUS_MODE_SWR BIT(0) /* software reset */
++#define DMA_BUS_MODE_BLE BIT(7) /* big endian mode */
++#define DMA_BUS_MODE_PBL_SHIFT 8 /* programmable burst length 32 */
++#define DMA_BUS_MODE_DBO BIT(20) /* big-endian descriptors */
++
++#define DMA_STATUS_TI BIT(0) /* transmit interrupt */
++#define DMA_STATUS_TPS BIT(1) /* transmit process stopped */
++#define DMA_STATUS_TU BIT(2) /* transmit buffer unavailable */
++#define DMA_STATUS_TJT BIT(3) /* transmit buffer timeout */
++#define DMA_STATUS_UNF BIT(5) /* transmit underflow */
++#define DMA_STATUS_RI BIT(6) /* receive interrupt */
++#define DMA_STATUS_RU BIT(7) /* receive buffer unavailable */
++#define DMA_STATUS_RPS BIT(8) /* receive process stopped */
++#define DMA_STATUS_ETI BIT(10) /* early transmit interrupt */
++#define DMA_STATUS_FBE BIT(13) /* fatal bus interrupt */
++#define DMA_STATUS_ERI BIT(14) /* early receive interrupt */
++#define DMA_STATUS_AIS BIT(15) /* abnormal interrupt summary */
++#define DMA_STATUS_NIS BIT(16) /* normal interrupt summary */
++#define DMA_STATUS_RS_SHIFT 17 /* receive process state */
++#define DMA_STATUS_TS_SHIFT 20 /* transmit process state */
++#define DMA_STATUS_EB_SHIFT 23 /* error bits */
++
++#define DMA_CONTROL_SR BIT(1) /* start receive */
++#define DMA_CONTROL_ST BIT(13) /* start transmit */
++#define DMA_CONTROL_SF BIT(21) /* store and forward */
++
++
++typedef struct {
++ volatile unsigned int status; // OWN, Device control and status.
++ volatile unsigned int devcs; // pkt Control bits + Length
++ volatile unsigned int addr; // Current Address.
++ volatile unsigned int descr; // Next descriptor in chain.
++} ar231x_descr_t;
++
++
++
++//
++// New Combo structure for Both Eth0 AND eth1
++//
++typedef struct {
++ volatile unsigned int mac_control; /* 0x00 */
++ volatile unsigned int mac_addr[2]; /* 0x04 - 0x08 */
++ volatile unsigned int mcast_table[2]; /* 0x0c - 0x10 */
++ volatile unsigned int mii_addr; /* 0x14 */
++ volatile unsigned int mii_data; /* 0x18 */
++ volatile unsigned int flow_control; /* 0x1c */
++ volatile unsigned int vlan_tag; /* 0x20 */
++ volatile unsigned int pad[7]; /* 0x24 - 0x3c */
++ volatile unsigned int ucast_table[8]; /* 0x40-0x5c */
++
++} ETHERNET_STRUCT;
++
++/********************************************************************
++ * Interrupt controller
++ ********************************************************************/
++
++typedef struct {
++ volatile unsigned int wdog_control; /* 0x08 */
++ volatile unsigned int wdog_timer; /* 0x0c */
++ volatile unsigned int misc_status; /* 0x10 */
++ volatile unsigned int misc_mask; /* 0x14 */
++ volatile unsigned int global_status; /* 0x18 */
++ volatile unsigned int reserved; /* 0x1c */
++ volatile unsigned int reset_control; /* 0x20 */
++} INTERRUPT;
++
++/********************************************************************
++ * DMA controller
++ ********************************************************************/
++typedef struct {
++ volatile unsigned int bus_mode; /* 0x00 (CSR0) */
++ volatile unsigned int xmt_poll; /* 0x04 (CSR1) */
++ volatile unsigned int rcv_poll; /* 0x08 (CSR2) */
++ volatile unsigned int rcv_base; /* 0x0c (CSR3) */
++ volatile unsigned int xmt_base; /* 0x10 (CSR4) */
++ volatile unsigned int status; /* 0x14 (CSR5) */
++ volatile unsigned int control; /* 0x18 (CSR6) */
++ volatile unsigned int intr_ena; /* 0x1c (CSR7) */
++ volatile unsigned int rcv_missed; /* 0x20 (CSR8) */
++ volatile unsigned int reserved[11]; /* 0x24-0x4c (CSR9-19) */
++ volatile unsigned int cur_tx_buf_addr; /* 0x50 (CSR20) */
++ volatile unsigned int cur_rx_buf_addr; /* 0x50 (CSR21) */
++} DMA;
++
++/*
++ * Struct private for the Sibyte.
++ *
++ * Elements are grouped so variables used by the tx handling goes
++ * together, and will go into the same cache lines etc. in order to
++ * avoid cache line contention between the rx and tx handling on SMP.
++ *
++ * Frequently accessed variables are put at the beginning of the
++ * struct to help the compiler generate better/shorter code.
++ */
++struct ar231x_private {
++ struct net_device *dev;
++ int version;
++ u32 mb[2];
++
++ volatile ETHERNET_STRUCT *phy_regs;
++ volatile ETHERNET_STRUCT *eth_regs;
++ volatile DMA *dma_regs;
++ volatile u32 *int_regs;
++ struct ar231x_eth *cfg;
++
++ spinlock_t lock; /* Serialise access to device */
++
++ /*
++ * RX and TX descriptors, must be adjacent
++ */
++ ar231x_descr_t *rx_ring;
++ ar231x_descr_t *tx_ring;
++
++
++ struct sk_buff **rx_skb;
++ struct sk_buff **tx_skb;
++
++ /*
++ * RX elements
++ */
++ u32 rx_skbprd;
++ u32 cur_rx;
++
++ /*
++ * TX elements
++ */
++ u32 tx_prd;
++ u32 tx_csm;
++
++ /*
++ * Misc elements
++ */
++ char name[48];
++ struct {
++ u32 address;
++ u32 length;
++ char *mapping;
++ } desc;
++
++
++ struct timer_list link_timer;
++ unsigned short phy; /* merlot phy = 1, samsung phy = 0x1f */
++ unsigned short mac;
++ unsigned short link; /* 0 - link down, 1 - link up */
++ u16 phyData;
++
++ struct tasklet_struct rx_tasklet;
++ int unloading;
++
++ struct phy_device *phy_dev;
++ struct mii_bus *mii_bus;
++ int oldduplex;
++};
++
++
++/*
++ * Prototypes
++ */
++static int ar231x_init(struct net_device *dev);
++#ifdef TX_TIMEOUT
++static void ar231x_tx_timeout(struct net_device *dev);
++#endif
++static int ar231x_restart(struct net_device *dev);
++static void ar231x_load_rx_ring(struct net_device *dev, int bufs);
++static irqreturn_t ar231x_interrupt(int irq, void *dev_id);
++static int ar231x_open(struct net_device *dev);
++static int ar231x_start_xmit(struct sk_buff *skb, struct net_device *dev);
++static int ar231x_close(struct net_device *dev);
++static int ar231x_ioctl(struct net_device *dev, struct ifreq *ifr,
++ int cmd);
++static void ar231x_init_cleanup(struct net_device *dev);
++static int ar231x_setup_timer(struct net_device *dev);
++static void ar231x_link_timer_fn(unsigned long data);
++static void ar231x_check_link(struct net_device *dev);
++#endif /* _AR2313_H_ */
projects / openwrt / svn-archive / archive.git / blobdiff